WorldWideScience

Sample records for plasma transferred arc

  1. Plasma transferred arc deposition of beryllium

    Science.gov (United States)

    Hollis, K.; Bartram, B.; Withers, J.; Storm, R.; Massarello, J.

    2006-12-01

    The exceptional properties of beryllium (Be), including low density and high elastic modulus, make it the material of choice in many defense and aerospace applications. However, health hazards associated with Be material handling limit the applications that are suited for its use. Innovative solutions that enable continued use of Be in critical applications while addressing worker health concerns are highly desirable. Plasma transferred arc solid free-form fabrication is being evaluated as a Be fabrication technique for civilian and military space-based components. Initial experiments producing Be deposits are reported here. Deposit shape, microstructure, and mechanical properties are reported.

  2. Characterization of Mullite-Zirconia Composite Processed by Non-Transferred and Transferred Arc Plasma

    Institute of Scientific and Technical Information of China (English)

    S. YUGESWARAN; V. SELVARAJAN; L. LUSVARGHI; A. I. Y. TOK; D. SIVA RAMA KRISHNA

    2009-01-01

    The arc plasma melting technique is a simple method to synthesize high temperature reaction composites. In this study, mullite-zirconia composite was synthesized by transferred and non-transferred arc plasma melting, and the results were compared. A mixture of alumina and zircon powders with a mole ratio of 3 : 2 were ball milled for four hours and melted for two minutes in the transferred and non-transferred mode of plasma arcs. Argon and air were used as plasma forming gases. The phase and microstructural formation of melted samples were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). The microstructure of the com-posites was found to be affected by the mode of melting. In transferred arc melting, zirconia flowers with uniform lines along with mullite whiskers were obtained. In the case of non-transferred arc plasma melting, mullite whiskers along with star shape zirconia were formed. Differential thermal analysis (DTA) of the synthesized mullite-zirconia composites provided a deeper understanding of the mechanisms of mullite formation during the two different processes.

  3. Ni/Al Intermetallics Plasma Transferred Arc Processing

    Institute of Scientific and Technical Information of China (English)

    VeronicaA.B.Almeida; AnaSofiaC.M.D'Oliveira

    2004-01-01

    In-situ alloy development during surface processing allows for a limitless materials selection to protect components exposed to severe service conditions. In fact surface alloying offers the possibility to strengthen surface components with alloys that would not be possible to process otherwise. This work used Plasma transferred arc (PTA) hardfacing for surface alloying. Different amounts of aluminium powder, 5-25%, were added to a Ni based superalloy, from Hastealloy C family, in the atomized form. The mixture was homogeneized in a ball mill and PTA deposited on carbon steel substrate. The influence of different processing parameters on the final surface alloy was evaluated as current intensity and depositing velocity were varied. Coatings were characterized by optical and scanning electronic microscopy, X-ray diffraction and Vickers microhardness profiles, under a 500g load. Results showed that PTA hardfacing is an adequate surface alloying. For the conditions tested increasing hardness was obtained by solid solution for the lower amounts of Al added and due to the new intermetallic phases for the richer Al mixture.

  4. Ni/Al Intermetallics Plasma Transferred Arc Processing

    Institute of Scientific and Technical Information of China (English)

    Ver(o)nica A. B. Almeida; Ana Sofia C. M. D'Oliveira

    2004-01-01

    In-situ alloy development during surface processing allows for a limitless materials selection to protect components exposed to severe service conditions. In fact surface alloying offers the possibility to strengthen surface components with alloys that would not be possible to process otherwise. This work used Plasma transferred arc (PTA) hardfacing for surface alloying. Different amounts of aluminium powder, 5-25%, were added to a Ni based superalloy, from Hastealloy C family, in the atomized form. The mixture was homogeneized in a ball mill and PTA deposited on carbon steel substrate. The influence of different processing parameters on the final surface alloy was evaluated as current intensity and depositing velocity were varied. Coatings were characterized by optical and scanning electronic microscopy, X-ray diffraction and Vickers microhardness profiles, under a 500g load. Results showed that PTA hardfacing is an adequate surface alloying. For the conditions tested increasing hardness was obtained by solid solution for the lower amounts of Al added and due to the new intermetallic phases for the richer Al mixture.

  5. Multigroup Approximation of Radiation Transfer in SF6 Arc Plasmas

    Directory of Open Access Journals (Sweden)

    Milada Bartlova

    2013-01-01

    Full Text Available The first order of the method of spherical harmonics (P1-approximation has been used to evaluate the radiation properties of arc plasmas of various mixtures of SF6 and PTFE ((C2F4n, polytetrafluoroethylene in the temperature range (1000 ÷ 35 000 K and pressures from 0.5 to 5 MPa. Calculations have been performed for isothermal cylindrical plasma of various radii (0.01 ÷ 10 cm. The frequency dependence of the absorption coefficients has been handled using the Planck and Rosseland averaging methods for several frequency intervals. Results obtained using various means calculated for different choices of frequency intervals are discussed.

  6. Heat Transfer Affected by Transverse Magnetic Field using 3D Modeling of Arc Plasma

    Science.gov (United States)

    Maeda, Yoshifumi; Tanaka, Tatsuro; Yamamoto, Shinji; Iwao, Toru

    2016-10-01

    Gas shielded metal arc welding is used to join the various metal because this is the high quality joining technology. Thus, this welding is used for a welding of large buildings such as bridges and LNG tanks. However, the welding defect caused by the heat transfer decrement may occur with increasing the wind velocity. This is because that the convection loss increases because the arc deflects to leeward side with increasing the wind velocity. In order to prevent from the arc deflection, it is used that the transverse magnetic field is applied to the arc. However, the arc deflection occurs with increasing the transverse magnetic field excessively. The energy balance of the arc is changed with increasing the convection loss caused by the arc deflection, and the heat transfer to the anode decreases. Therefore, the analysis including the arc and anode is necessary to elucidate the heat transfer to the anode. In this paper, the heat transfer affected by the transverse magnetic field using 3D modeling of the arc plasma is elucidated. The heat transfer to the anode is calculated by using the EMTF(electromagnetic thermal fluid) simulation with increasing the transverse magnetic field. As a result, the heat transfer decreased with increasing the transverse magnetic field.

  7. Pulsed plasma arc cladding

    Institute of Scientific and Technical Information of China (English)

    龙; 白钢; 李振民; 张赋升; 杨思乾

    2004-01-01

    A prototype of Pulsed Plasma Arc Cladding system was developed, in which single power source supplies both transferred plasma arc (TPA) and non-transferred plasma arc (N-TPA). Both plasmas work in turn in a high frequency controlled by an IGBT connecting nozzle and workpiece. The working frequency of IGBT ranges from 50 ~ 7000Hz, in which the plasmas can work in turn smoothly. Higher than 500 Hz of working frequency is suggested for promotion of cladding quality and protection of IGBT. Drag phenomenon of TPA intensifies as the frequency goes up, which tends to increase the current proportion of TPA and suppress N-TPA. The occupation ratio of IGBT can be regulated from 5% ~ 95%, which balances the power supplies of both plasmas. An occupation ratio higher than 50% gives adequate proportion of arc current for N-TPA to preheat powder.

  8. Deposição por plasma com arco transferido Hardfacing by plasma transfer arc process

    Directory of Open Access Journals (Sweden)

    Víctor Vergara Díaz

    2010-03-01

    Full Text Available Em virtude do Processo de Soldagem Plasma com Alimentação de Pó ter similaridades com o Processo de Soldagem Plasma com Alimentação de Arame, foi realizado um estudo comparativo entre ambos os processos utilizando-se a liga a base de cobalto comercialmente conhecida como Stellite 6, como material de adição na forma de pó e arame. A pesquisa foi realizada com a expectativa de ser aplicada nas operações de revestimentos de superfícies, em especial em pás de turbinas hidráulicas desgastadas por cavitação. A seleção do material de adição a ser empregado depende da natureza do mecanismo de desgaste encontrado. No Labsolda, a liga Stellite 6 vem sendo uma das mais utilizadas, por apresentar uma excelente resistência ao desgaste erosivo por cavitação. Foi avaliada a influência da vazão de gás de plasma a partir dos valores de diluição, dimensões do cordão, dureza e microestrutura. O Processo de Soldagem Plasma com Alimentação de Pó foi o que produziu o melhor acabamento superficial, menor diluição, melhor molhamento e maior largura. Com isto abre-se uma nova perspectiva para revestimentos metálicos e neste contexto se insere a recuperação por soldagem de partes erodidas de turbinas hidráulicas.The Plasma powder transferred arc welding process, which uses feed stock in the powder form, has similarities with Plasma wire transferred arc welding. This work describes a comparative study of the two processes using a Cobalt-based alloy commercially known as Stellite 6. This Co-based alloy is recognized for its superior cavitation erosion resistance. The aim of this work is to investigate the potential of PTA coatings for the protection and refurbishiment hydraulic turbine blades. Coatings were evaluated for the influence of Plasma gas flow rate on coating dilution, geometry, hardness and microstructure. Coatings processed with the atomized Stellite 6 powder feestock showed a superior surface quality, lower dilution

  9. Synthesis of few layer graphene by non-transferred arc plasma system.

    Science.gov (United States)

    Baek, Jong-Jun; Kim, Tae-Hee; Park, Dong-Wha

    2013-11-01

    Graphene has recently been the focus of a great deal of attention owing to its outstanding properties, which include high mobility, high thermal conductivity and high structural stability. In this study, a few layer graphene was successfully synthesized from methane gas using a non-transferred direct current arc plasma system. Non-transferred thermal plasma offers high temperature, steep temperature gradient and high enthalpy to enhance the reaction kinetics of graphene synthesis. In order to prepare high quality few layer graphene, graphene products synthesized under several conditions was analyzed comparatively. Effects of gap distance between the plasma torch and graphite substrate, the flow rate of additional reactant gas, and different types of plasma forming gas on the synthesis of few layer graphene were investigated. Methane gas was injected into the plasma jet as a carbon source for the synthesis of graphene and a thermal plasma jet was generated by pure argon or a mixture of argon-hydrogen. The results revealed that hydrogen gas improved the quality of few layer graphene by inducing surface etching and increasing plasma power.

  10. Finite Element Simulation of Plasma Transferred ARC Welding [PTAW] of Structural Steel

    Directory of Open Access Journals (Sweden)

    PV Senthiil

    2014-10-01

    Full Text Available Plasma transferred Arc welding is one of the most widely used welding process, in which the metals are fused just above the melting point, and makes the metal to fuse. It is employed in many applications like tool die and metal casting, strip metal welding etc. This investigation is to analyze temperature distribution residual stress and distortion by varying the heat source parameter in SYSWELD, and compared the results with ANSYS. The simulation of Plasma Transferred Arc welding was of structural steel plate performed using a non-linear transient heat transfer analysis. Heat losses due to convection and variation of material properties with temperature were considered in this analysis. To incorporate the heat developed the Gaussian distribution was considered. Finite element simulations were performed using ANSYS Parametric Design Language (APDL code and using SYSWELD. The temperatures obtained were compared with experimental results for validation. It was found that the predicted values of temperature agree very well with the experimental values. Residual Stress and Distortion were also predicted for various heat Input. The effect of heat input on residual stress and distortion was investigated.

  11. Plasma Transferred ARC (PTA Hardfacing of Recycled Hardmetal Reinforced Nickel-matrix Surface Composites

    Directory of Open Access Journals (Sweden)

    Arkadi ZIKIN

    2012-03-01

    Full Text Available The aim of this work was to apply coarse recycled hardmetal particles in combination with Ni-based matrix to produce wear resistant metal matrix composite (MMC thick coatings using plasma transferred arc hardfacing (PTA technology. Assignment of hardmetal waste as initial material can significantly decrease the production costs and improve the mechanical properties of coatings and, consequently, increase their wear resistance. The microstructure of MMC fabricated from a recycled powder was examined by optical and SEM/EDS microscopes, whereas quantitative analyses were performed by image analysis method. Micro-mechanical properties, including hardness and elastic modulus of features, were measured by nanoindentation. Furthermore, behaviour of materials subjected to abrasive and impact conditions was studied. Results show the recycled powder provides hardfacings of high quality which can be successfully used in the fabrication of wear resistant MMC coatings by PTA-technology.DOI: http://dx.doi.org/10.5755/j01.ms.18.1.1334

  12. NiCrSiB Coatings Deposited by Plasma Transferred Arc on Different Steel Substrates

    Science.gov (United States)

    Reinaldo, P. R.; D'Oliveira, A. S. C. M.

    2013-02-01

    Colmonoy 6 (NiCrSiB) is a Ni-based alloy recognized for its superior mechanical properties, attributed to the presence of a dispersion of hard carbides and borides, which is strongly dependent on processing technique. This work gathered microstructure data from the literature and analyzed Colmonoy 6 coatings deposited by plasma transferred arc hardfacing. The aim of the study was to determine the influence of PTA deposition parameters and substrate chemical composition on NiCrSiB coating characteristics. Coatings were characterized in terms of their hardness, dilution, and microstructure, as well as mass loss during abrasive sliding wear tests. The results showed that coating performance is strongly dependent on the chemical composition of the substrate. Carbon steel substrate yielded coatings with greater wear resistance. Processing parameters also alter the performance of coatings, and the lower current and lower travel speed result in reduced mass loss.

  13. Micro-Plasma Transferred Arc Additive Manufacturing for Die and Mold Surface Remanufacturing

    Science.gov (United States)

    Jhavar, Suyog; Paul, Christ Prakash; Jain, Neelesh Kumar

    2016-07-01

    Micro-plasma transferred arc ( µPTA) additive manufacturing is one of the newest options for remanufacturing of dies and molds surfaces in the near-millimeter range leading to extended usage of the same. We deployed an automatic micro-plasma deposition setup to deposit a wire of 300 µm of AISI P20 tool steel on the substrate of same material for the potential application in remanufacturing of the die and mold surface. Our present research effort is to establish µPTA additive manufacturing as a viable economical and cleaner methodology for potential industrial applications. We undertook the optimization of single weld bead geometry as the first step in our present study. Bead-on-plate trials were conducted to deposit single bead geometry at various processing parameters. The bead geometry (shape and size) and dilution were measured and the parametric dependence was derived. A set of parameters leading to reproducible regular and smooth single bead geometry were identified and used to prepare a thin wall for mechanical testing. The deposits were subjected to material characterization such as microscopic studies, micro-hardness measurements and tensile testing. The process was compared qualitatively with other deposition processes involving high-energy density beams and was found to be advantageous in terms of low initial and running costs with comparable properties. The outcome of the study confirmed the process capability of µPTA deposition leading to deployment of cost-effective and environmentally friendlier technology for die and mold remanufacturing.

  14. Arc Plasma Torch Modeling

    CERN Document Server

    Trelles, J P; Vardelle, A; Heberlein, J V R

    2013-01-01

    Arc plasma torches are the primary components of various industrial thermal plasma processes involving plasma spraying, metal cutting and welding, thermal plasma CVD, metal melting and remelting, waste treatment and gas production. They are relatively simple devices whose operation implies intricate thermal, chemical, electrical, and fluid dynamics phenomena. Modeling may be used as a means to better understand the physical processes involved in their operation. This paper presents an overview of the main aspects involved in the modeling of DC arc plasma torches: the mathematical models including thermodynamic and chemical non-equilibrium models, turbulent and radiative transport, thermodynamic and transport property calculation, boundary conditions and arc reattachment models. It focuses on the conventional plasma torches used for plasma spraying that include a hot-cathode and a nozzle anode.

  15. Effect of current and atomized grain size distribution on the solidification of Plasma Transferred Arc coatings

    Directory of Open Access Journals (Sweden)

    Danielle Bond

    2012-10-01

    Full Text Available Plasma Transferred Arc (PTA is the only thermal spray process that results in a metallurgical bond, being frequently described as a hardfacing process. The superior properties of coatings have been related to the fine microstructures obtained, which are finer than those processed under similar heat input with welding techniques using wire feedstock. This observation suggests that the atomized feedstock plays a role on the solidification of coatings. In this study a model for the role of the powders grains in the solidification of PTA coatings is put forward and discussed. An experiment was setup to discuss the model which involved the deposition of an atomized Co-based alloy with different grain size distributions and deposition currents. X ray diffraction showed that there were no phase changes due to the processing parameters. Microstructure analysis by Laser Confocal Microscopy, dilution with the substrate steel and Vickers microhardness were used the characterized coatings and enriched the discussion confirming the role of the powdered feedstock on the solidification of coatings.

  16. Deign of Experiment and Optimization of Plasma Transferred Arc Hardfacing on Structural Steel with Titanium Carbide

    Directory of Open Access Journals (Sweden)

    S. Balamurugan

    2014-03-01

    Full Text Available The aim of the Plasma Transferred Arc (PTA hardfacing process is improving a technical surface locally with a dedicated material; Hardfacing became an issue of intense development related to wear resistant application. The hardfacing procedures can be differentiated by the intensity of mixture with the base body, which is usually increasing along with an increasing fusion efficiency rate. Nearly all kinds of weldable materials can be hardfaced and mostly all types of known wear resistant metals in combination can be used as hardfacing materials. The PTA hardfacing process has been widely employed due to several advantages such as higher volume of metal deposition rates and achieving very low dilution level. Heat input which influences dilution can be controlled by proper selection of PTA process parameters. In this study, an attempt has been made to analyze PTA hardfacing of IS: 2062 structural steel with Titanium Carbide (TiC. Experiments were conducted based on a fully replicable five-factor, five-level central composite rotatable design. Mathematical models were developed using response surface methodology to study the effects of PTA hardfacing process parameters such as welding current, welding speed ,powder feed rate, oscillation width and pre heat temperature on bead geometry parameters like penetration, reinforcement, bead width and dilution. Direct and interaction effects of PTA process parameters on bead geometry were analyzed. From mathematical model, the process parameters were optimized.

  17. Modeling of Arc Force in Plasma Arc Welding

    Institute of Scientific and Technical Information of China (English)

    GAO Zhonglin; HU Shengsun; YIN Fengliang; WANG Rui

    2008-01-01

    A three. dimensional mathematical model for the transferred-type argon arc was developed to describe arc force on the anode surface. The software ANSYS was employed to solve the model. The model includes a part of torch and tungsten electrode to achieve m ore reasonable results. The arc temperature and flow fields were derived. And the influences of welding parameters on arc force were also studied. The simulated results show that arc pressure at the anode are dependent on the welding current, plasma gas flow rate and electrode neck-in, while not sensitive to arc length.

  18. Welding arc plasma physics

    Science.gov (United States)

    Cain, Bruce L.

    1990-01-01

    The problems of weld quality control and weld process dependability continue to be relevant issues in modern metal welding technology. These become especially important for NASA missions which may require the assembly or repair of larger orbiting platforms using automatic welding techniques. To extend present welding technologies for such applications, NASA/MSFC's Materials and Processes Lab is developing physical models of the arc welding process with the goal of providing both a basis for improved design of weld control systems, and a better understanding of how arc welding variables influence final weld properties. The physics of the plasma arc discharge is reasonably well established in terms of transport processes occurring in the arc column itself, although recourse to sophisticated numerical treatments is normally required to obtain quantitative results. Unfortunately the rigor of these numerical computations often obscures the physics of the underlying model due to its inherent complexity. In contrast, this work has focused on a relatively simple physical model of the arc discharge to describe the gross features observed in welding arcs. Emphasis was placed of deriving analytic expressions for the voltage along the arc axis as a function of known or measurable arc parameters. The model retains the essential physics for a straight polarity, diffusion dominated free burning arc in argon, with major simplifications of collisionless sheaths and simple energy balances at the electrodes.

  19. Application of Response Surface Methodolody to Prediction of Dilution in Plasma Transferred Arc Hardfacing of Stainless Steel on Carbon Steel

    Institute of Scientific and Technical Information of China (English)

    V Balasubramanian; A K Lakshminarayanan; R Varahamoorthy; S Babu

    2009-01-01

    The application of.response surface methodology was highlighted to predict and optimize the percentage of dilution of iron-based hardfaced surface produced by the PTA (plasma transferred arc welding) process.The experiments were conducted based on five-factor five-level central composite rotatable design with full replication technique and a mathematical model was developed using response surface methodology.Furthermore,the response surface methodology was also used to optimize the process parameters that yielded the lowest percentage of dilution.

  20. Study on Ceramic Cutting by Plasma Arc

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Engineering ceramics are typical difficult-to-machine materials because of high hardness and brittleness. PAC (Plasma Arc Cutting) is a very important thermal cutting process and has been successfully used in cutting stainless steel and other difficult-to-machine alloys. PAC's application in cutting ceramics, however, is still limited because the most ceramics are not good electronic conducts, and transferred plasma arc cannot be produced between cathode and work-piece. So we presented a method of plasma ...

  1. Gas arc constriction for plasma arc welding

    Science.gov (United States)

    McGee, William F. (Inventor); Rybicki, Daniel J. (Inventor)

    1994-01-01

    A welding torch for plasma arc welding apparatus has an inert gas applied circumferentially about the arc column externally of the constricting nozzle so as to apply a constricting force on the arc after it has exited the nozzle orifice and downstream of the auxiliary shielding gas. The constricting inert gas is supplied to a plenum chamber about the body of the torch and exits through a series of circumferentially disposed orifices in an annular wall forming a closure at the forward end of the constricting gas plenum chamber. The constricting force of the circumferential gas flow about the arc concentrates and focuses the arc column into a more narrow and dense column of energy after exiting the nozzle orifice so that the arc better retains its energy density prior to contacting the workpiece.

  2. Comparisons of particles thermal behavior between Fe-base alloy and boron carbide during plasma transferred-arc powder surfacing

    Institute of Scientific and Technical Information of China (English)

    王惜宝

    2003-01-01

    Comparisons of particle's thermal behavior between Fe-base alloy and boron carbide in plasma transferred-arc (PTA) space was made based on theoretical evaluation results in this article. It was found that most of the Fe base particles would be fully melted while they transporting through the central plasma field with 200 A surfacing currents. And the particles with a diameter less than 0.5×10-4 m might be fully evaporated. However, for the boron carbide (B4C) particles, only the one with a diameter less than 0.5×10-4 m could be melted in the same PTA space. Most of B4C particles are only preheated at its solid state when they were fed through the central field of PTA plasma when the surfacing current is equal to or less than 200 A. When the arc current was smaller than100 A, only the particles smaller than 0.5×10-4 m could be melted in the PTA space for the Fe-base alloy. Almost none of the discussed B4C particles could be melted in the 100 A PTA space.

  3. NUMERICAL MODELING OF HEAT TRANSFER AND FLUID FLOW IN KEYHOLE PLASMA ARC WELDING OF DISSIMILAR STEEL JOINTS

    Directory of Open Access Journals (Sweden)

    M. A. Daha

    2012-02-01

    Full Text Available The evolution of temperature profiles and weld pool geometry during dissimilar welding between 2205 duplex stainless steel and A36 low carbon steel using keyhole plasma arc welding has been simulated using a three dimensional numerical heat transfer and fluid flow model. An adaptive heat source is proposed as a heat source model for performing a non-linear transient thermal analysis, based on the configuration feature of keyhole plasma arc welds. Temperature profiles and solidified weld pool geometry are presented for three different welding heat input. The reversed bugle shape parameters (width of fusion zone at both top and bottom surfaces of the weld pool geometry features for a dissimilar 2205–A36 weld joint are summarized to successfully explain the observations. The model was also applied to keyhole plasma welding of 6.8 mm thick similar 2205 duplex stainless steel joint for validation. The simulation results were compared with independently obtained experimental data and good agreements have been obtained.

  4. Metrology in arc plasmas - A new cathode

    Science.gov (United States)

    Croche, R.

    1980-02-01

    A new radiating source consisting of an electric arc under argon pressure is described, with power varying between about 0.2 and 1.5 kW, and with the plasma furnishing a continuous spectrum between 115 and 350 nm. The arc functions from 5 to 50 A, with a voltage varying between 30 and 35 V. The cathode of the transfer arc is described in detail, including such advantages as easy igniting of the arc and the possibility of re-sharpening the tip of the cathode. Most important, the new 'knife-shaped' form of the tungsten cathode has improved the stability and reproducibility of the ultraviolet continuum emitted by the plasma of the arc, which is used at the French National Institute of Metrology as a transfer standard of spectral radiance in the vacuum ultraviolet.

  5. Influences of the microstructure on the wear resistance of cobalt-based ahoy coatings obtained by plasma transferred arc process

    Institute of Scientific and Technical Information of China (English)

    HOU Qingyu; GAO Jiasheng

    2005-01-01

    The microstructure, substructure, and wear characteristic of cobalt-based alloy coatings obtained by plasma transferred arc (PTA) process were investigated using optical metallurgical microscope, X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and dry sand abrasion tester (DSAT). The aging effect on the structure and wear resistance of the cobalt-based PTA coating was also studied. The results show that the as-welded coating consists of cobalt-based solid solution with face-centered cubic structure and hexagonal (Cr, Fe)7C3. There are a lot of stacking faults existing in the cobalt-based solid solution. After aging at 600℃ for 60 h, the microstructure becomes coarse, and another carbide (Cr, Fe)23C6 precipitates. As a result, the wear mass loss of the aged sample is higher than that of the as-welded sample.

  6. Plasma arc cutting technology: simulation and experiments

    Energy Technology Data Exchange (ETDEWEB)

    Cantoro, G; Colombo, V; Concetti, A; Ghedini, E; Sanibondi, P; Zinzani, F; Rotundo, F [Department of Mechanical Engineering (D.I.E.M.) and Research Center for Applied Mathematics (C.I.R.A.M.), Alma Mater Studiorum-Universita di Bologna, Via Saragozza 8, 40123 Bologna (Italy); Dallavalle, S; Vancini, M, E-mail: emanuele.ghedini@unibo.it [Cebora S.p.A., Via Andrea Costa 24, 40057 Cadriano di Granarolo (Italy)

    2011-01-01

    Transferred arc plasma torches are widely used in industrial processes for cutting of metallic materials because of their ability to cut a wide range of metals with very high productivity. The process is characterized by a transferred electric arc established between an electrode inside the torch (the cathode) and another electrode, the metallic workpiece to be cut (the anode). In order to obtain a high quality cut and a high productivity, the plasma jet must be as collimated as possible and must have the higher achievable power density. Plasma modelling and numerical simulation can be very useful tools for the designing and optimizing these devices, but research is still in the making for finding a link between simulation of the plasma arc and a consistent prevision of cut quality. Numerical modelling of the behaviour of different types of transferred arc dual gas plasma torches can give an insight on the physical reasons for the industrial success of various design and process solutions that have appeared over the last years. Diagnostics based on high speed imaging and Schlieren photography can play an important role for investigating piercing, dross generation, pilot arcing and anode attachment location. Also, the behaviour of hafnium cathodes at high current levels at the beginning of their service life can been experimentally investigated, with the final aim of understanding the phenomena that take place during those initial piercing and cutting phases and optimizing the initial shape of the surface of the emissive insert exposed to plasma atmosphere.

  7. Arc Root Attachment on the Anode Surface of Arc Plasma Torch Observed with a Novel Method

    Institute of Scientific and Technical Information of China (English)

    PAN Wen-Xia; LI Teng; MENG Xian; CHEN Xi; WU Cheng-Kang

    2005-01-01

    @@ The arc-root attachment on the anode surface of a dc non-transferred arc plasma torch has been successfullyobserved using a novel approach. A specially designed copper mirror with a boron nitride film coated on itssurface central-region is employed to avoid the effect of intensive light emitted from the arc column upon theobservation of weakly luminous arc root. It is found that the arc-root attachment is diffusive on the anode surfaceof the argon plasma torch, while constricted arc roots often occur when hydrogen or nitrogen is added into argonas the plasma-forming gas.

  8. Order Reduction of the Radiative Heat Transfer Model for the Simulation of Plasma Arcs

    CERN Document Server

    Fagiano, Lorenzo

    2015-01-01

    An approach to derive low-complexity models describing thermal radiation for the sake of simulating the behavior of electric arcs in switchgear systems is presented. The idea is to approximate the (high dimensional) full-order equations, modeling the propagation of the radiated intensity in space, with a model of much lower dimension, whose parameters are identified by means of nonlinear system identification techniques. The low-order model preserves the main structural aspects of the full-order one, and its parameters can be straightforwardly used in arc simulation tools based on computational fluid dynamics. In particular, the model parameters can be used together with the common approaches to resolve radiation in magnetohydrodynamic simulations, including the discrete-ordinate method, the P-N methods and photohydrodynamics. The proposed order reduction approach is able to systematically compute the partitioning of the electromagnetic spectrum in frequency bands, and the related absorption coefficients, tha...

  9. STUDY ON THE PRESSURE IN PLASMA ARC

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The axial pressure in plasma arc is measured under different conditions. The effects of the parameters, such as welding current, plasma gas flow rate, electrode setback and arc length, on the pressure in plasma arc are investigated and quantitative analyzed to explain the relationship between the quality of weld and the matching of parameters in plasma arc welding process.

  10. Energy Balance in DC Arc Plasma Melting Furnace

    Institute of Scientific and Technical Information of China (English)

    ZHAO Peng; MENG Yuedong; YU Xinyao; CHEN Longwei; JIANG Yiman; NI Guohua; CHEN Mingzhou

    2009-01-01

    In order to treat hazardous municipal solid waste incinerator's (MSWI) fly ash, a new DC arc plasma furnace was developed. Taking an arc of 100 V/1000 A DC as an example,the heat transfer characteristics of the DC arc plasma, ablation of electrodes, heat properties of the fly ash during melting, heat transfer characteristics of the flue gas, and heat loss of the furnace were analyzed based on the energy conservation law, so as to achieve the total heat information and energy balance during plasma processing, and to provide a theoretical basis for an optimized design of the structure and to improve energy efficiency.

  11. Modelling the Plasma Jet in Multi-Arc Plasma Spraying

    Science.gov (United States)

    Bobzin, K.; Öte, M.; Schein, J.; Zimmermann, S.; Möhwald, K.; Lummer, C.

    2016-08-01

    Particle in-flight characteristics in atmospheric plasma spraying process are determined by impulse and heat energy transferred between the plasma jet and injected powder particles. One of the important factors for the quality of the plasma-sprayed coatings is thus the distribution of plasma gas temperatures and velocities in plasma jet. Plasma jets generated by conventional single-arc plasma spraying systems and their interaction with powder particles were subject matter of intensive research. However, this does not apply to plasma jets generated by means of multi-arc plasma spraying systems yet. In this study, a numerical model has been developed which is designated to dealing with the flow characteristics of the plasma jet generated by means of a three-cathode spraying system. The upstream flow conditions, which were calculated using a priori conducted plasma generator simulations, have been coupled to the plasma jet simulations. The significances of the relevant numerical assumptions and aspects of the models are analyzed. The focus is placed on to the turbulence and diffusion/demixing modelling. A critical evaluation of the prediction power of the models is conducted by comparing the numerical results to the experimental results determined by means of emission spectroscopic computed tomography. It is evident that the numerical models exhibit a good accuracy for their intended use.

  12. Miniaturized cathodic arc plasma source

    Science.gov (United States)

    Anders, Andre; MacGill, Robert A.

    2003-04-15

    A cathodic arc plasma source has an anode formed of a plurality of spaced baffles which extend beyond the active cathode surface of the cathode. With the open baffle structure of the anode, most macroparticles pass through the gaps between the baffles and reflect off the baffles out of the plasma stream that enters a filter. Thus the anode not only has an electrical function but serves as a prefilter. The cathode has a small diameter, e.g. a rod of about 1/4 inch (6.25 mm) diameter. Thus the plasma source output is well localized, even with cathode spot movement which is limited in area, so that it effectively couples into a miniaturized filter. With a small area cathode, the material eroded from the cathode needs to be replaced to maintain plasma production. Therefore, the source includes a cathode advancement or feed mechanism coupled to cathode rod. The cathode also requires a cooling mechanism. The movable cathode rod is housed in a cooled metal shield or tube which serves as both a current conductor, thus reducing ohmic heat produced in the cathode, and as the heat sink for heat generated at or near the cathode. Cooling of the cathode housing tube is done by contact with coolant at a place remote from the active cathode surface. The source is operated in pulsed mode at relatively high currents, about 1 kA. The high arc current can also be used to operate the magnetic filter. A cathodic arc plasma deposition system using this source can be used for the deposition of ultrathin amorphous hard carbon (a-C) films for the magnetic storage industry.

  13. Influence of Plasma Transferred Arc Process Parameters on Structure and Mechanical Properties of Wear Resistive NiCrBSi-WC/Co Coatings

    Directory of Open Access Journals (Sweden)

    Eitvydas GRUZDYS

    2011-07-01

    Full Text Available Self-fluxing NiCrBSi and related coatings received considerable interest due to their good wear as well as corrosion resistance at moderate and elevated temperatures. Hard tungsten carbide (WC particles can be included in NiCrBSi for further increase of the coating hardness and abrasive wear resistance. Flame spray technique is widely used for fabrication of NiCrBSi films. However, in such a case, subsequent remelting of the deposited coatings by flame, arc discharge or high power laser beam is necessary. In present study NiCrBSi-WC/Co coatings were formed using plasma transferred arc process. By adjusting plasma parameters, such as current, plasma gas flow, shielding gas flow, a number of coatings were formed on steel substrates. Structure of the coatings was investigated using X-ray diffractometry. Microstructure of cross-sectioned coatings was examined using scanning electron microscopy. Hardness of the coating was evaluated by means of the Vickers hardness tests. Wear tests were also performed on specimens to determine resistance to abrasive wear. Acquired results allowed estimating the influence of the deposition process parameters on structure and mechanical properties of the coatings.http://dx.doi.org/10.5755/j01.ms.17.2.482

  14. THE INVESTIGATION ON PLASMA ARC TREATMENT OF CHROMIUM PLATED ALLOY STRUCTURE STEEL

    Institute of Scientific and Technical Information of China (English)

    X.M. Fan; J.W. Huang; K.H. Wang; Q. Liu

    2005-01-01

    The technology of plasma arc was used to modify the interface adhesion between chromium coating and steel substrate. The interface microstructure was studied as a function of plasma arc processing parameters. Microstructure analysis was performed by optical microscopy,scanning electron microscopy and electron probe. The microhardness distribution along the depth of a cross-section of the chromium coating and the substrate was measured. The results show the energy density of transferred plasma arc is obviously higher than plasma non-transferred arc. The molten interface was obtained by plasma transferred arc. Interfaces between chromium coating and steel substrate can be divided by plasma non-transferred arc into three classes: non-molten, a little molten and molten. Good interface bonding was obtained by proper process parameters. The microhardness of chromium coating decreases with increasing energy density of plasma arc.

  15. NTWV-based sensing keyhole dimension in plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    Jia Chuanbao; Wu Chuansong; Zhang Yuming

    2008-01-01

    During stable keyhole plasma arc welding, the pilot arc and the transferred arc exist at the meantime, and the arcs can be considered as a composition of two parts inside and outside the nozzle, respectively. Under the mechanical constriction and thermal contraction effects, the inside arc has certain arc length, electron density and arc profile etc. Inducing constant tungsten-to-nozzle voltage. However, the arc outside the nozzle diverges at about 5 degrees and has certain characteristics similar to the free arcs. The nozzle-to-workpiece voltage (NTWV) depends mainly on the length of the arc, which gets bigger as increasing of the weld penetration and keyhole size. The NTWV sensor is developed for monitoring NTWV in real time. The welding experiments are designed to get different penetrations and keyhole sizes. It is found that as the weld penetration and the keyhole size increase, NTWV also increases linearly. The NTWV signals can be used as the feedback variable in automatic control of keyhole plasma arc welding.

  16. Characteristics of Single-Track and Multi-track Depositions of Stellite by Micro-plasma Transferred Arc Powder Deposition Process

    Science.gov (United States)

    Sawant, Mayur S.; Jain, N. K.

    2017-08-01

    This paper describes the characteristics study of single-track and multi-track deposition of Stellite 6 on AISI 4130 steel substrate by indigenously developed micro-plasma transferred arc powder deposition (μ-PTAPD) process. Deposition height and width, dilution and microstructure have been used to characterize the single-track depositions by studying effects of micro-plasma power, travel speed of worktable and powder mass flow rate on energy consumption per unit traverse length and power consumption per unit powder mass flow rate. Micro-plasma power was found to be the most influential parameter that affects energy and deposition material consumption. Consequently, its influence on micro-hardness and abrasion resistance of multi-track deposition was studied. Results showed that increase in micro-plasma power decreases micro-hardness and scratch hardness number and increases mean value of friction coefficient. Comparison of microstructure and chemical composition of single-track and multi-track depositions revealed that single-track has finer dendritic microstructure than the multi-track deposition. The black colored matrix and white colored dendrites present in the multi-track deposition have higher wt.% of cobalt and less wt.% of chromium than the single-track deposition. Comparison of µ-PTAPD process capabilities with the existing processes for Stellite deposition establishes that it is an energy-efficient, cost-effective and good quality deposition yielding process.

  17. Application of Steenbeck's minimum principle for three-dimensional modelling of DC arc plasma torches

    CERN Document Server

    Li He Ping; Chen, X

    2003-01-01

    In this paper, physical/mathematical models for the three-dimensional, quasi-steady modelling of the plasma flow and heat transfer inside a non-transferred DC arc plasma torch are described in detail. The Steenbeck's minimum principle (Finkelnburg W and Maecker H 1956 Electric arcs and thermal plasmas Encyclopedia of Physics vol XXII (Berlin: Springer)) is employed to determine the axial position of the anode arc-root at the anode surface. This principle postulates a minimum arc voltage for a given arc current, working gas flow rate, and torch configuration. The modelling results show that the temperature and flow fields inside the DC non-transferred arc plasma torch show significant three-dimensional features. The predicted anode arc-root attachment position and the arc shape by employing Steenbeck's minimum principle are reasonably consistent with experimental observations. The thermal efficiency and the torch power distribution are also calculated in this paper. The results show that the thermal efficiency...

  18. Numerical and experimental study of transferred arcs in argon

    Energy Technology Data Exchange (ETDEWEB)

    Bini, R [Department of Mechanical Engineering, Politecnico di Milano, Via Bonardi 9, 20133 Milan (Italy); Monno, M [Department of Mechanical Engineering, Politecnico di Milano, Via Bonardi 9, 20133 Milan (Italy); Boulos, M I [Centre de Recherche en Energie, Plasma et Electrochimie (CREPE), Department de Genie Chimique Universite de Sherbrooke, 2500 Boul. Universite, Sherbrooke, J1K1R2 (Canada)

    2006-08-07

    The bidimensional model of the electric arc is enhanced with the plasma-electrodes interaction to predict the properties and the energy distribution of an argon arc operating with current intensities between 100 and 200 A and electrode gaps of 10 and 20 mm. An adaptive numerical insulation is applied to the cathode, to properly simulate its thermionic emission mechanism and overcome the dependence on empirical distributions of the current density at its tip. The numerical results are quantitatively compared with the data obtained from calorimetric and spectroscopical measurements, performed on a device which generates a transferred arc between a water cooled copper anode and a thoriated tungsten cathode enclosed in a stainless steel chamber. The calculation of the heat fluxes towards the electrodes permits to determine the amount of power delivered to each component of the arc system (the anode, the cathode assembly and the chamber) and to evaluate the overall efficiency of the process for different configurations. The agreement between theory and data, over the range of parameters investigated, is sensible both in the temperature profiles and in the energy distributions. In such configurations, the conduction from the hot gas is the most relevant term in the overall heat transferred to the anode, but it is the electron transfer which rules the heat transfer in the arc attachment zone. The arc attachment radius is also dependent on the process parameters and increases with the arc current (from approximately 5 mm at 100 A to 7 mm at 200 A) and the arc length. However the maximum heat flux reached on the axis decreases increasing the gap between the electrodes, although more power is delivered to the anode due to the radial spreading of the plasma. A 10 mm 200 A argon arc releases to the anode about 2.6 kW, which corresponds to 75% of the total arc power available. If the arc is extended to 20 mm the power transferred rises by nearly 350 W, but the overall

  19. Heat transfer modeling of double-side arc welding

    CERN Document Server

    Sun Jun Sheng; Zhang Yan Ming

    2002-01-01

    If a plasma arc and a TIG arc are connected in serial and with the plasma arc placed on the obverse side and the TIG arc on the opposite side of the workpiece, a special double-side arc welding (DSAW) system will be formed, in which the PAW current is forced to flow through the keyhole along the thickness direction so as to compensate the energy consumed for melting the workpiece and improve the penetration capacity of the PAW arc. By considering the mechanics factors which influence the DSAW pool geometric shape, the control equations of the pool surface deformation are derived, and the mathematics mode for DSAW heat transfer is established by using boundary-fitted non-orthogonal coordinate systems. With this model, the difference between DSAW and PAW heat transfer is analyzed and the reason for the increase of DSAW penetration is explained from the point of heat transfer. The welding process experiments show that calculated results are in good agreement with measured ones

  20. Three Filtered Vacuum Arc Plasma Sources Deposition & Implantation System

    Institute of Scientific and Technical Information of China (English)

    WU Xian-ying; ZHANG Hui-xing; LI Qiang

    2004-01-01

    A deposition & implantation system, which includes three filtered vacuum arc plasma sources, has been built. Vacuum arc discharge is used to produce high-density metal plasma; Curved magnetic filtering technique is used to transfer the plasma into out-of-sight vacuum chamber and reduce macro-particles from the vacuum arc plasma in order to drastically reduce the macro-particles contamination of the films. The up to 30 kV negative bias applied to the target can be used for ion implantation in order to improve the film adhesion; or for ion sputtering to clear the substrate surface. The 0 to 300 V negative bias can be used to adjust the ion energy which forming films. The system is designed for various thin films synthesizing, such as single-layer, compound layer, multi-layer films. It's principle, components and applications are described in the literature.

  1. Gas Tungsten Arc Welding and Plasma Arc Cutting. Teacher Edition.

    Science.gov (United States)

    Fortney, Clarence; And Others

    This welding curriculum guide treats two topics in detail: the care of tungsten electrodes and the entire concept of contamination control and the hafnium electrode and its importance in dual-air cutting systems that use compressed shop air for plasma arc cutting activities. The guide contains three units of instruction that cover the following…

  2. Fluid Flow Modeling of Arc Plasma and Bath Circulation in DC Electric Arc Furnace

    Institute of Scientific and Technical Information of China (English)

    WANG Feng-hua; JIN Zhi-jian; ZHU Zi-shu

    2006-01-01

    A mathematical model describing the flow field, heat transfer and the electromagnetic phenomenon in a DC electric arc furnace has been developed. First the governing equations in the arc plasma region are solved and the calculated results of heat transfer, current density and shear stresses on the anode surface are used as boundary conditions in a model of molten bath. Then a two-dimensional time-dependent model is used to describe the flow field and electromagnetic phenomenon in the molten bath. Moreover, the effect of bottom electrode diameter on the circulation of molten bath is studied.

  3. Plasma distribution of cathodic ARC deposition system

    Energy Technology Data Exchange (ETDEWEB)

    Anders, S.; Raoux, S.; Krishnan, K.; MacGill, R.A.; Brown, I.G. [Lawrence Berkeley National Lab., CA (United States)

    1996-08-01

    The plasma distribution using a cathodic arc plasma source with and without magnetic macroparticle filter has been determined by depositing on a transparent plastic substrate and measuring the film absorption. It was found that the width of the distribution depends on the arc current, and it also depends on the cathode material which leads to a spatial separation of the elements when an alloy cathode is used. By applying a magnetic multicusp field near the exit of the magnetic filter, it was possible to modify the plasma distribution and obtain a flat plasma profile with a constant and homogeneous elemental distribution.

  4. Cathodic Vacuum Arc Plasma of Thallium

    OpenAIRE

    Yushkov, Georgy Yu.; Anders, Andre

    2006-01-01

    Thallium arc plasma was investigated in a vacuum arc ion source. As expected from previous consideration of cathode materials in the Periodic Table of the Elements, thallium plasma shows lead-like behavior. Its mean ion charge state exceeds 2.0 immediately after arc triggering, reaches the predicted 1.60 and 1.45 after about 100 microsec and 150 microsec, respectively. The most likely ion velocity is initially 8000 m/s and decays to 6500 m/s and 6200 m/s after 100 microsec and 150 micros...

  5. Electric-Arc Plasma Installation for Preparing Nanodispersed Carbon Structures

    Institute of Scientific and Technical Information of China (English)

    P. STEFANOV; D. GARLANOV; G. VISSOKOV

    2008-01-01

    An electric-arc plasma installation operated in the hidden anode arrangement is constructed and used for the preparation of carbon nanostructures. A contracted plasma arc gen-erated by a plasma torch using an inert gas is used as heat source. The average mass temperature of arc is higher than 104 K, while its power density, which is directly transferred onto the electrode (anode), is ~ 2 kW/mm2. The anode contact area formed on the electrode moves against the arc by way of shifting the electrode and is hidden completely in the interior of plasma gas stream moving towards it. As a result of both the direct plasma attack and the opposite movement of streams in the hidden anode contact area, a temperature higher than 6000 K is reached. Thus, intensive vaporization takes place, which forms a saturated plasma-gas-aerosol phase of the initial material of electrode (anode). This gas phase is mixed in and carried by the plasma stream. Over that mixed plasma stream, a controlled process of quenching (fixation) is carried out by twisted turbulent fluid streams. After the fixation, the resultant carbon nano-structures are caught by a filter and collected in a bunker.

  6. Effects of Y2O3 on the microstructure and wear resistance of cobalt-based alloy coatings deposited by plasma transferred arc process

    Institute of Scientific and Technical Information of China (English)

    HOU Qingyu; HUANG Zhenyi; GAO Jiasheng

    2007-01-01

    Cobalt-based alloys with different Y2O3 contents were deposited on Q235A-carbon steel using plasma transferred arc (PTA) welding machine. The effect of Y2O3 on the microstructure and wear resistance properties of the cobalt-based alloys were investigated using an optical microscope, a scanning electron microscope (SEM), X-ray diffraction (XRD), and transmission electron microscopy (TEM). It was found that a cobalt-based solid solution with a face-centered cubic crystal structure was presented accompanied by the secondary phase M7C3 with a hexagonal crystal structure in the Y2O3-free cobalt-based alloy coating. Several stacking faults exist in the cobalt-based solid solution. The addition of Y2O3leads to the existence of the Y2O3 phase in the Y2O3-modified coatings. Though stacking fault exists in the Y2O3-modified coatings, its density increases. The addition of Y2O3 can refine the microstructure and can increase the wear resistance properties when its contents are less than or equal to 0.8 wt.%. However, further increase of its contents will lead to the agglomeration of undissolved Y2O3 particles at the γ-Co grain boundary, and will lead to a coarse microstructure and lower wear resistance properties.

  7. Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

    Institute of Scientific and Technical Information of China (English)

    Da-wen Zeng

    2015-01-01

    In this work, an in situ synthesized TiC-reinforced metal matrix composite (MMC) coating of approximately 350–400μm thick-ness was fabricated on a gray cast iron (GCI) substrate by plasma transferred arc (PTA) surface alloying of Ti–Fe alloy powder. Microhard-ness tests showed that the surface hardness increased approximately four-fold after the alloying treatment. The microstructure of the MMC coating was mainly composed of residual austenite, acicular martensite, and eutectic ledeburite. Scanning electron microscopy (SEM) and X-ray diffraction analyzes revealed that the in situ TiC particles, which were formed by direct reaction of Ti with carbon originally contained in the GCI, was uniformly distributed at the boundary of residual austenite in the alloying zone. Pin-on-disc high-temperature wear tests were performed on samples both with and without the MMC coating at room temperature and at elevated temperatures (473 K and 623 K), and the wear behavior and mechanism were investigated. The results showed that, after the PTA alloying treatment, the wear resistance of the sam-ples improved significantly. On the basis of our analysis of the composite coatings by optical microscopy, SEM with energy-dispersive X-ray spectroscopy, and microhardness measurements, we attributed this improvement of wear resistance to the transformation of the microstruc-ture and to the presence of TiC particles.

  8. Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

    Science.gov (United States)

    Zhao, Hang; Li, Jian-jun; Zheng, Zhi-zhen; Wang, Ai-hua; Huang, Qi-wen; Zeng, Da-wen

    2015-12-01

    In this work, an in situ synthesized TiC-reinforced metal matrix composite (MMC) coating of approximately 350-400 µm thickness was fabricated on a gray cast iron (GCI) substrate by plasma transferred arc (PTA) surface alloying of Ti-Fe alloy powder. Microhardness tests showed that the surface hardness increased approximately four-fold after the alloying treatment. The microstructure of the MMC coating was mainly composed of residual austenite, acicular martensite, and eutectic ledeburite. Scanning electron microscopy (SEM) and X-ray diffraction analyzes revealed that the in situ TiC particles, which were formed by direct reaction of Ti with carbon originally contained in the GCI, was uniformly distributed at the boundary of residual austenite in the alloying zone. Pin-on-disc high-temperature wear tests were performed on samples both with and without the MMC coating at room temperature and at elevated temperatures (473 K and 623 K), and the wear behavior and mechanism were investigated. The results showed that, after the PTA alloying treatment, the wear resistance of the samples improved significantly. On the basis of our analysis of the composite coatings by optical microscopy, SEM with energy-dispersive X-ray spectroscopy, and microhardness measurements, we attributed this improvement of wear resistance to the transformation of the microstructure and to the presence of TiC particles.

  9. Microstructure and microhardness characterization of Cr{sub 3}C{sub 2}-SiC coatings produced by the plasma transferred arc method

    Energy Technology Data Exchange (ETDEWEB)

    Islak, Serkan [Kastamonu Univ. (Turkey). Cide Rifat Ilgaz Vocational High School; Eski, Oezkan [Kastamonu Univ. (Turkey). Kastamonu Vocational High School; Buytoz, Soner [Firat Univ., Elazig (Turkey). Dept. of Metallurgy and Materials Engineering; Karagoez, Muzaffer [Bartin Univ. (Turkey). Dept. of Metallurgical and Materials Engineering; Stokes, Joseph [Dublin City Univ. (Ireland). School of Mechanical and Manufacturing Engineering

    2012-07-01

    The purpose of this work was to investigate the coatings made of Cr{sub 3}C{sub 2} and SiC powder manufactured on AISI 304 stainless steel applied by the plasma transferred arc (PTA) welding process. SiC content in the produced coated layer was varied between 0-100 wt. % and the effect of SiC concentration on the microstructure and hardness of the coating was measured experimentally. SEM analyses revealed that the composite coatings had a homogeneous, nonporous, and crack-free microstructure. Dendrites and interdendrite eutectics formed on the coating layer, subject to the temperature gradient and the solidification ratio. There was a significant increase in the hardness of coating layers with the effect of the {gamma}-(Fe,Ni), Cr{sub 7}C{sub 3}, Cr{sub 23}C{sub 6}, Fe{sub 5}C{sub 2}, Cr{sub 3}Si, CrSi{sub 2}, Fe{sub 0.64}Ni{sub 0.36}, CFe{sub 15.1}, C-(Fe,Cr)-Si phases formed in the microstructure. In comparison to the substrate, the microhardness of the coatings produced by PTA were 2.5-3.5 times harder. (orig.)

  10. Using arc voltage to locate the anode attachment in plasma arc cutting

    Science.gov (United States)

    Osterhouse, D. J.; Lindsay, J. W.; Heberlein, J. V. R.

    2013-06-01

    Plasma arc cutting is a widely used industrial process in which an electric arc in the form of a high velocity plasma jet is used to melt and blow away metal. The arc attaches inside the resulting cut slot, or kerf, where it both provides a large heat flux and determines the flow dynamics of the plasma. Knowledge of the position of the arc attachment is essential for understanding the phenomena present at the work piece. This work presents a new method of measuring the location of the arc attachment in which the arc voltage is measured during the cutting of a range of work piece thicknesses. The attachment location is then interpreted from the voltages. To support the validity of this method, the kerf shape, dross particle size and dross adhesion to the work piece are also observed. While these do not conclusively give an attachment location, they show patterns which are consistent with the attachment location found from the voltage measurements. The method is demonstrated on the cutting of mild steel, where the arc attachment is found to be stationary in the upper portion of the cut slot and in reasonable agreement with existing published findings. For a process optimized for the cutting of 12.7 mm mild steel, the attachment is found at a depth of 1.5-3.4 mm. For a slower process optimized for the cutting of 25.4 mm mild steel, the attachment is found at a depth of 3.4-4.8 mm, which enhances heat transfer further down in the kerf, allowing cutting of the thicker work piece. The use of arc voltage to locate the position of the arc attachment is unique when compared with existing methods because it is entirely independent of the heat distribution and visualization techniques.

  11. Hypergravity effects on glide arc plasma

    NARCIS (Netherlands)

    Šperka, J.; Souček, P.; van Loon, J.J.W.A.; Dowson, A.; Schwarz, C.; Krause, J.; Kroesen, G.; Kudrle, V.

    2013-01-01

    The behaviour of a special type of electric discharge - the gliding arc plasma - has been investigated in hypergravity (1g-18g) using the Large Diameter Centrifuge (LDC) at ESA/ESTEC. The discharge voltage and current together with the videosignal from a fast camera have been recorded during the exp

  12. Plasma Arc Augmented CO2 laser welding

    DEFF Research Database (Denmark)

    Bagger, Claus; Andersen, Mikkel; Frederiksen, Niels

    2001-01-01

    In order to reduce the hardness of laser beam welded 2.13 mm medium strength steel CMn 250, a plasma arc has been used simultaneously with a 2.6 kW CO2 laser source. In a number of systematic laboratory tests, the plasma arc current, plasma gas flow and distance to the laser source were varied...... with all laser parameters fixed. The welds were quality assessed and hardness measured transversely to the welding direction in the top, middle and root of the seam. In the seams welded by laser alone, hardness values between 275 and 304 HV1 were measured, about the double of the base material, 150 HV1...

  13. Gliding arc triggered microwave plasma arc at atmospheric pressure for coal gasification application

    Science.gov (United States)

    Jain, Vishal; Visani, A.; Patil, C.; Patel, B. K.; Sharma, P. K.; John, P. I.; Nema, S. K.

    2014-08-01

    Plasma torch is device that efficiently converts electrical energy in to thermal energy for various high temperature applications. The conventional plasma torch comprises of consumable electrodes namely anode and cathode electrodes. The replacement of these electrodes is a complex process owing to its cooling and process shut down requirements. However, microwave plasma arc is electrode-less plasma arc system that is an alternative method to conventional arc technology for generating plasma arc. In this technique, microwave power is efficiently coupled to generate plasma arc by using the property of polar molecule to absorb microwave power. The absorption of microwave power is in form of losses due to intermolecular friction and high collisions between the molecules. This is an efficient method because all microwave power can be absorbed by plasma arc. The main feature of microwave plasma arc is its large uniform high temperature column which is not possible with conventional arc discharge methods. Such type of plasma discharge is very useful in applications where sufficient residence time for treat materials is required. Microwave arc does not require any consumable electrodes and hence, it can be operated continuously that makes it very useful for hazardous effluent treatment applications. Further, microwave cannot ionize neutral particles at atmospheric pressure and hence, a gliding arc is initiated between two thin electrodes in the cavity by applying very low power high voltage (3kV) AC source. In this report, the method for generating microwave arc of 1kW power using commercial microwave oven is elaborated.

  14. The variable polarity plasma arc welding process: Characteristics and performance

    Science.gov (United States)

    Hung, R. J.; Zhu, G. J.

    1991-01-01

    Significant advantages of the Variable Polarity Plasma Arc (VPPA) Welding Process include faster welding, fewer repairs, less joint preparation, reduced weldment distortion, and absence of porosity. The power distribution was analyzed for an argon plasma gas flow constituting the fluid in the VPPA Welding Process. The major heat loss at the torch nozzle is convective heat transfer; in the space between the outlet of the nozzle and the workpiece; radiative heat transfer; and in the keyhole in the workpiece, convective heat transfer. The power absorbed at the workpiece produces the molten puddle that solidifies into the weld bead. Crown and root widths, and crown and root heights of the weld bead are predicted. The basis is provided for an algorithm for automatic control of VPPA welding machine parameters to obtain desired weld bead dimensions.

  15. Process characteristics of fibre-laser-assisted plasma arc welding

    OpenAIRE

    Mahrle, A; SCHNICK, M; Rose, S; Demuth, C; Beyer, E.; Füssel, U

    2011-01-01

    Abstract Experimental and theoretical investigations on fibre-laser assisted plasma arc welding (LAPW) have been performed. Welding experiments were carried out on aluminium and steel sheets. In case of a highly focused laser beam and a separate arrangement of plasma torch and laser beam, high-speed video recordings of the plasma arc and corresponding measurements of the time-dependent arc voltage revealed differences in the process behaviour for both materials. In case of aluminium weldin...

  16. Process characteristics of fibre-laser-assisted plasma arc welding

    Energy Technology Data Exchange (ETDEWEB)

    Mahrle, A; Schnick, M; Rose, S; Demuth, C; Beyer, E; Fuessel, U, E-mail: achim.mahrle@iws.fraunhofer.de [Dresden University of Technology, Institute of Surface and Manufacturing Technology, PO Box, D-01062 Dresden (Germany)

    2011-08-31

    Experimental and theoretical investigations on fibre-laser-assisted plasma arc welding (LAPW) were performed. Welding experiments were carried out on aluminium and steel sheets. In the case of a highly focused laser beam and a separate arrangement of plasma torch and laser beam, high-speed video recordings of the plasma arc and corresponding measurements of the time-dependent arc voltage revealed differences in the process behaviour for both materials. In the case of aluminium welding, a sharp decline in arc voltage and stabilization and guiding of the anodic arc root was observed whereas in steel welding the arc voltage was slightly increased after the laser beam was switched on. However, significant improvement of the melting efficiency with the combined action of plasma arc and laser beam was achieved for both types of material. Theoretical results of additional numerical simulations of the arc behaviour suggest that the properties of the arc plasma are mainly influenced not by a direct interaction with the laser radiation but by the laser-induced evaporation of metal. Arc stabilization with increased current densities is predicted for moderate rates of evaporated metal only whereas metal vapour rates above a certain threshold causes a destabilization of the arc and reduced current densities along the arc axis.

  17. Plasma Arc Surface Hardening Robot Technology

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In national economy and national defense, a lot of ma chine components become worthless early because of wear and tear and corrode. It leads to huge loss of resource and material. Surface hardening of the steel cou ld form a hard, wearable, corrode-resisting layer on the surface to enhance the mechanical property of the machine component. From 1980s, there is a new method of surface hardening that is heating with plasma arc. It overcomes the shortage of old methods and is adopted in automotive product ...

  18. Plasma ARC keyhole welding of aluminum

    Science.gov (United States)

    Fostervoll, H.

    1993-02-01

    An increasing and more advanced use of aluminum as a construction material make higher demands to the effectiveness and quality in aluminum joining. Furthermore, if the advantages of aluminum shall be exploited in the best possible way, it is necessary to use the best processes available for the certain application. Today, the most widely used processes of aluminum welding are gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW). Plasma arc welding (PAW) is another interesting process, which is rather newly adopted for aluminum welding. However, up to now the use is limited and most of the users are within the space industry in USA (NASA); also the new space industry in Europe has adopted the process. The reason for the great interest for PAW in the space industry is, according to NASA, higher weld quality and less repair costs, less heat distortion, and less groove preparations costs. Of these reasons, PAW should also be of interest for the aluminum industry in Scandinavia. The aim of the project is to focus on the possibilities and to some extent testing the PAW process.

  19. Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hao; ZHU Fengsen; TU Xin; BO Zheng; CEN Kefa; LI Xiaodong

    2016-01-01

    In this work,a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions.The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals,high speed photography,and optical emission spectroscopic diagnostics.Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g.,10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone,in this RGA system,a lower gas flow rate (e.g.,2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions.Two different motion patterns can be clearly observed in the N2 and air RGA plasmas.The time-resolved arc voltage signals show that three different arc dynamic modes,the arc restrike mode,takeover mode,and combined modes,can be clearly identified in the RGA plasmas.The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.

  20. Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

    Science.gov (United States)

    Zhang, Hao; Zhu, Fengsen; Tu, Xin; Bo, Zheng; Cen, Kefa; Li, Xiaodong

    2016-05-01

    In this work, a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions. The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals, high speed photography, and optical emission spectroscopic diagnostics. Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g., 10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone, in this RGA system, a lower gas flow rate (e.g., 2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions. Two different motion patterns can be clearly observed in the N2 and air RGA plasmas. The time-resolved arc voltage signals show that three different arc dynamic modes, the arc restrike mode, takeover mode, and combined modes, can be clearly identified in the RGA plasmas. The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate. supported by National Natural Science Foundation of China (No. 51576174), the Specialized Research Fund for the Doctoral Program of Higher Education of China (No. 20120101110099) and the Fundamental Research Funds for the Central Universities (No. 2015FZA4011)

  1. Modeling Plasma-Particle Interaction in Multi-Arc Plasma Spraying

    Science.gov (United States)

    Bobzin, K.; Öte, M.

    2017-01-01

    The properties of plasma-sprayed coatings are controlled by the heat, momentum, and mass transfer between individual particles and the plasma jet. The particle behavior in conventional single-arc plasma spraying has been the subject of intensive numerical research, whereas multi-arc plasma spraying has not yet received the same attention. We propose herein a numerical model to serve as a scientific tool to investigate particle behavior in multi-arc plasma spraying. In the Lagrangian description of particles in the model, the mathematical formulations describing the heat, momentum, and mass transfer are of great importance for good predictive power, so such formulations proposed by different authors were compared critically, revealing that different mathematical formulations lead to significantly different results. The accuracy of the different formulations was evaluated based on theoretical considerations, and those found to be more accurate were implemented in the final model. Furthermore, a mathematical formulation is proposed to enable simplified calculation of partial particle melting and resolidification.

  2. A novel 300 kW arc plasma inverter system based on hierarchical controlled building block structure

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    To date, the high power arc plasma technology is widely used. A next generation high power arc plasma system based on building block structure is presented. The whole arc plasma inverter system is composed of 12 paralleled units to increase the system output capability. The hierarchical control system is adopted to improve the reliability and flexibility of the high power arc plasma inverter. To ensure the reliable turn on and off of the IGBT module in each building block unit, a special pulse drive circuit is designed by using pulse transformer. The experimental result indicates that the high power arc plasma inverter system can transfer 300 kW arc plasma energy reliably with high efficiency.

  3. Numerical Study on Arc Plasma Behavior During Arc Commutation Process in Direct Current Circuit Breaker

    Institute of Scientific and Technical Information of China (English)

    杨飞; 马瑞光; 吴翊; 孙昊; 纽春萍; 荣命哲

    2012-01-01

    This paper focuses on the numerical investigation of arc plasma behavior during arc commutation process in a medium-voltage direct current circuit breaker (DCCB) contact system. A three-dimensional magneto-hydrodynamic (MHD) model of air arc plasma in the contact system of a DCCB is developed, based on commercial software FLUENT. Coupled electromagnetic and gas dynamic interactions are considered as usual, and a thin layer of nonlinear electrical resistance elements is used to represent the voltage drop of plasma sheath and the formation of new arc root. The distributions of pressure, temperature, gas flow and current density of arc plasma in arc region are calculated. The simulation results indicate that the pressure distribution related to the contact system has a strong effect on the arc commutation process, arising from the change of electrical conductivity in the arc root region. In DCCB contact system, the pressure of arc root region will be concentrated and higher if the space above the moving contact is enclosed, which is not good for arc root commutation. However, when the region is opened, the pressure distribution would be lower and more evenly, which is favorable for the arc root commutation.

  4. Discharge Characteristics of DC Arc Water Plasma for Environmental Applications

    Institute of Scientific and Technical Information of China (English)

    LI Tianming; Sooseok CHOI; Takayuki WATANABE

    2012-01-01

    A water plasma was generated by DC arc discharge with a hafnium embedded rodtype cathode and a nozzle-type anode. The discharge characteristics were examined by changing the operation parameter of the arc current. The dynamic behavior of the arc discharge led to significant fluctuations in the arc voltage and its frequency. Analyses of the high speed image and the arc voltage waveform showed that the arc discharge was in the restrike mode and its frequency varied within several tens of kilohertz according to the operating conditions. The larger thermal plasma volume was generated by the higher flow from the forming steam with a higher restrike frequency in the higher arc current conditions. In addition, the characteristics of the water plasma jet were investigated by means of optical emission spectroscopy to identify the abundant radicals required in an efficient waste treatment process.

  5. Dependence of Arc Plasma Dispersion Capability on its Temperature

    Institute of Scientific and Technical Information of China (English)

    CHEN Yun-Yun; SONG Yang; HE An-Zhi; LI Zhen-Hua

    2008-01-01

    @@ The relationship between the dispersion capability and the temperature of argon arc plasma at Iatm is deduced in view of the plasma's refractive index equation.The results indicate that argon arc plasma has a normal dispersion and its dispersion capability is nonlinear to the plasma's temperature in a wide range of temperature and wavelength region.According to the results of numerical calculation, the preferred optical methods are believed to be suitable for the diagnosis of argon arc plasma in different temperature regions.

  6. Computational study of flow dynamics from a dc arc plasma jet

    CERN Document Server

    Trelles, Juan Pablo

    2013-01-01

    Plasma jets produced by direct-current (DC) non-transferred arc plasma torches, at the core of technologies ranging from spray coating to pyrolysis, present intricate dynamics due to the coupled interaction of fluid flow, thermal, and electromagnetic phenomena. The flow dynamics from an arc discharge plasma jet are investigated using time-dependent three-dimensional simulations encompassing the dynamics of the arc inside the torch, the evolution of the jet through the discharge environment, and the subsequent impingement of the jet over a flat substrate. The plasma is described by a chemical equilibrium and thermodynamic nonequilibrium (two-temperature) model. The numerical formulation of the physical model is based on a monolithic and fully-coupled treatment of the fluid and electromagnetic equations using a Variational Multiscale Finite Element Method. Simulation results uncover distinct aspects of the flow dynamics, including the jet forcing due to the movement of the electric arc, the prevalence of deviat...

  7. Numerical modeling of transferred arc melting bath heating; Modelisation numerique du chauffage de bains par arc transfere

    Energy Technology Data Exchange (ETDEWEB)

    Bouvier, A. [Electricite de France, 77 - Moret sur Loing (France). Direction des Etudes et Recherches; Trenty, L.; Guillot, J.B. [Ecole Centrale de Paris, Laboratoire EM2C. CNRS, 92 - Chatenay-Malabry (France); Delalondre, C. [Electricite de France (EDF), 78 - Chatou (France). Direction des Etudes et Recherches

    1997-12-31

    This paper presents the modeling of a transferred electric arc inside a bath of melted metal. After a recall of the context of the study, the problem of the modeling, which involves magnetohydrodynamic coupling inside the arc and the bath, is described. The equations that govern the phenomena inside the arc and the bath are recalled and the approach used for the modeling of the anode region of the arc is explained using a 1-D sub-model. The conditions of connection between arc and bath calculations are explained and calculation results obtained with a 200 kW laboratory furnace geometry are presented. (J.S.) 8 refs.

  8. Robotic Variable Polarity Plasma Arc (VPPA) Welding

    Science.gov (United States)

    Jaffery, Waris S.

    1993-01-01

    The need for automated plasma welding was identified in the early stages of the Space Station Freedom Program (SSFP) because it requires approximately 1.3 miles of welding for assembly. As a result of the Variable Polarity Plasma Arc Welding (VPPAW) process's ability to make virtually defect-free welds in aluminum, it was chosen to fulfill the welding needs. Space Station Freedom will be constructed of 2219 aluminum utilizing the computer controlled VPPAW process. The 'Node Radial Docking Port', with it's saddle shaped weld path, has a constantly changing surface angle over 360 deg of the 282 inch weld. The automated robotic VPPAW process requires eight-axes of motion (six-axes of robot and two-axes of positioner movement). The robot control system is programmed to maintain Torch Center Point (TCP) orientation perpendicular to the part while the part positioner is tilted and rotated to maintain the vertical up orientation as required by the VPPAW process. The combined speed of the robot and the positioner are integrated to maintain a constant speed between the part and the torch. A laser-based vision sensor system has also been integrated to track the seam and map the surface of the profile during welding.

  9. Anode heat transfer in a constricted tube arc.

    Science.gov (United States)

    Lukens, L. A.; Incropera, F. P.

    1971-01-01

    The complex energy exchange mechanisms occurring on the most severely heated component of an arc constrictor, the anode, have been investigated. Measurements performed to determine the anode heat flux for a cascade, atmospheric argon arc of the Maecker type are described. The results are used to check the validity of an existing anode heat transfer model.

  10. Radioactive waste combustion / vitrification under arc plasma: thermal and dynamic modelling; Combustion - vitrification de dechets radioactifs par plasma d'arc: modelisation de la thermique et de la dynamique

    Energy Technology Data Exchange (ETDEWEB)

    Barthelemy, B

    2003-07-01

    This thesis concerns the thermal and dynamic modelling for a combustion/vitrification process of surrogate radioactive waste under transferred arc plasma. The writer presents the confinement processes for radioactive waste using arc plasma and the different software used to model theses processes. This is followed by a description of our experimental equipment including a plasma arc reactor and an inductive system allowing the homogenization of glass temperature. A combustion/vitrification test is described. Thermal and material balances were discussed. The temperature fields of plasma arc and the glass frit conductivity are measured. Finally, the writer describes and clarifies the equations solved for the simulations of the electrically plasma arc and the glass melting including the thin layer of glass frit coating the crucible cold walls. The modelling results are presented in the form of spatial distribution of temperature, velocity and volume power... (author)

  11. Radioactive waste combustion-vitrification under arc plasma: thermal and dynamic modelling; Combustion - vitrification de dechets radioactifs par plasma d'arc: modelisation de la thermique et de la dynamique

    Energy Technology Data Exchange (ETDEWEB)

    Barthelemy, B

    2003-06-01

    This thesis concerns the thermal and dynamic modelling for a combustion/vitrification process of surrogate radioactive waste under transferred arc plasma. The writer presents the confinement processes for radioactive waste using arc plasma and the different software used to model theses processes. This is followed by a description of our experimental equipment including a plasma arc reactor and an inductive system allowing the homogenization of glass temperature. A combustion/vitrification test is described. Thermal and material balances were discussed. The temperature fields of plasma arc and the glass frit conductivity are measured. Finally, the writer describes and clarifies the equations solved for the simulations of the electrically plasma arc and the glass melting including the thin layer of glass frit coating the crucible cold walls. The modelling results are presented in the form of spatial distribution of temperature, velocity and voluminal power... (author)

  12. Fluctuation Phenomenon Analysis of an Arc Plasma Spraying Jet

    Institute of Scientific and Technical Information of China (English)

    赵文华; 田阔; 刘笛; 张冠忠

    2001-01-01

    The effects of three factors, including the power supply, the arc behaviour in the arc channel and the fluid dynamic process of the jet, on a plasma spraying jet have been experimentally detected by means of spectroscopic diagnostic techniques. The fast Fourier transform method has been applied to the analysis of the arc voltage and spectral line intensity of the jet. The three factors have been studied and distinguished from each other.

  13. Improvement on Diamond Nucleation Treated by Pulsed Arc Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    马志斌; 万军; 汪建华; 张文文

    2004-01-01

    A technique of improvement on diamond nucleation based on pulsed arc discharge plasma at atmospheric pressure was developed. The pulsed arc discharge was induced respectively by nitrogen, argon and methanol gas. After the arc plasma pretreatment, a nucleation density higher than 1010 cm-2 may be obtained subsequently in chemical vapor deposition (CVD) on a mirror-polished silicon substrate without any other mechanical treatment. The effects of the arc discharge plasma on the diamond nucleation were investigated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), infrared spectroscopy (IR) and Raman spectroscopy. The enhancement of nucleation is postulated to be a result of the formation of carbonlike phase materials or nitrogenation on the substrate surface without surface defect produced by arc discharge.

  14. Plasma diagnostics in gas metal arc welding by optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Valensi, F; Pellerin, S; Zielinska, S [GREMI, Universite d' Orleans (Site de Bourges)/CNRS, BP 4043, 18028 Bourges cedex (France); Boutaghane, A [Universite des Sciences et de la Technologie Houari Boumediene, Alger (Algeria); Dzierzega, K [Marian Smoluchowski Institute of Physics, Jagellonian University, Krakow (Poland); Pellerin, N [CNRS, UPR3079 CEMHTI, 1D av. de la Recherche Scientifique, 45071 Orleans cedex 2 (France); Briand, F, E-mail: flavien.valensi@laplace.univ-tsle.f, E-mail: stephane.pellerin@univ-orleans.f, E-mail: aboutaghane@yahoo.f, E-mail: krzycho@netmail.if.uj.edu.p, E-mail: sylwia.zielinska@airliquide.co, E-mail: nadia.pellerin@univ-orleans.f, E-mail: francis.briand@airliquide.co [CTAS-Air Liquide Welding, Saint Ouen l' Aumone, 95315 Cergy-Pontoise cedex (France)

    2010-11-03

    The plasma column in a metal inert gas welding process is investigated by optical emission spectroscopy and high-speed imaging. The concentration and repartition of iron vapours are measured and correlated with the plasma and electrode geometric configuration. Plasma temperatures and electron densities are also measured for each studied position in the plasma. The temperatures are calculated using two different methods, allowing validation of the local thermodynamic equilibrium state of the plasma. The results show a maximum temperature of 12 500 K in the upper part of the arc, away from the arc axis. The iron concentration reaches a maximum of 0.3% close to the anode and strongly decreases along both the vertical and radial directions. The plasma thermophysical properties, calculated from this plasma composition, are then discussed regarding the metal transfer mode.

  15. Arc Behavior and Droplet Transfer of CWW CO2 Welding

    Institute of Scientific and Technical Information of China (English)

    Zhi-dong YANG; Chen-fu FANG; Yong CHEN; Guo-xiang XU; Qing-xian HU; Xiao-yan GU

    2016-01-01

    Cable-type welding wire (CWW)CO2 welding is an innovative process arc welding with high quality,high efficiency and energy saving,in which CWW is used as consumable electrode.The CWW is composed of seven wires with a diameter of 1.2 mm.One is in the center,while others uniformly distribute around it.The diameter of twisted wire is up to 3.6 mm,which can increase the deposition rate significantly.With continual wire-feeding and melting of CWW,the formed rotating arc improved welding quality obviously.The arc behavior and droplet transfer were ob-served by the electrical signal waveforms and corresponding synchronous images,based on the high speed digital camera and electrical signal system.The results showed that the shape of welding arc changed from bell arc to beam arc with the increase of welding parameter.The droplet transfer mode changed from repelled transfer,globular transfer to projected transfer in turn.Droplet transfer frequency increased from 18.17 Hz to 119.05 Hz,while the droplet diameter decreased from 1.5 times to 0.3 times of the CWW diameter.

  16. Variable-Polarity Plasma Arc Welding Of Alloy 2219

    Science.gov (United States)

    Walsh, Daniel W.; Nunes, Arthur C., Jr.

    1989-01-01

    Report presents results of study of variable-polarity plasma arc (VPPA) welding of aluminum alloy 2219. Consists of two parts: Examination of effects of microsegregation and transient weld stress on macrosegregation in weld pool and, electrical characterization of straight- and reverse-polarity portions of arc cycle.

  17. A plasma-arc pyrolysis system for hazardous waste treatment

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ A laboratory system for the treatment of medical and hazardous wastes via AC plasma-arc pyrolysis was recently built up by a research team led by Prof. SHENG Hongzhi at the CAS Institute of Mechanics (IMECH) in Beijing.

  18. Assistant Anode in a Cathodic Arc Plasma Source

    Institute of Scientific and Technical Information of China (English)

    张涛; Paul K. Chu; 张荟星; Ian G. Brown

    2001-01-01

    The performance and characteristics of a cathodic arc plasma source, consisting of a titanium cathode, an anode with and without a tungsten mesh, and a coil producing a focusing magnetic field between the anode and cathode,are investigated. The high transparency and large area of the mesh allow a high plasma flux to penetrate the anode from the cathodic arc. The mesh helps to decrease the arc resistance and the ignition voltage of the cathodic arc in the focusing magnetic field, and to increase the life of the source, which means that the source makes the cathodic arc easily and greatly stabilized during the operation when a focusing magnetic field exists in the source.

  19. Plasma backflow phenomenon in high-current vacuum arc

    Energy Technology Data Exchange (ETDEWEB)

    Wang Lijun [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Jia Shenli [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Zhang Ling [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Shi Zongqian [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Yang Dingge [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Gentils, Francois [Schneider Electric SAS, 37 quai Paul-Louis Merlin, 38050 Grenoble Cedex 9 (France); Jusselin, BenoIt [Schneider Electric SAS, 37 quai Paul-Louis Merlin, 38050 Grenoble Cedex 9 (France)

    2007-10-07

    Based on the two-temperature magnetohydrodynamic model, a high-current vacuum arc (HCVA) in vacuum interrupters is simulated and analysed. The phenomenon of plasma backflow in arc column is found, which is ultimately ascribed to the strong magnetic pinch effect of HCVA. Due to plasma backflow, the maximal value of ion density at the cathode side is not located at the centre of the cathode side, but at the paraxial region of the cathode side, that is to say, ion density appears to sag at the centre of the cathode side (arc column seems to be divided into two parts). The sag of light intensity is also found by experiments.

  20. Kinetic Modeling of Plasma Methane Conversion Using Gliding Arc

    Institute of Scientific and Technical Information of China (English)

    Antonius Indarto; Jae-Wook Choi; Hwaung Lee; Hyung Keun Song

    2005-01-01

    Plasma methane (CH4) conversion in gliding arc discharge was examined. The result data of experiments regarding the performance of gliding arc discharge were presented in this paper. A simulation which is consisted some chemical kinetic mechanisms has been provided to analyze and describe the plasma process. The effect of total gas flow rate and input frequency refers to power consumption have been studied to evaluate the performance of gliding arc plasma system and the reaction mechanism of decomposition.Experiment results indicated that the maximum conversion of CH4 reached 50% at the total gas flow rate of 1 L/min. The plasma reaction was occurred at the atmospheric pressure and the main products were C (solid), hydrogen, and acetylene (C2H2). The plasma reaction of methane conversion was exothermic reaction which increased the product stream temperature around 30-50 ℃.

  1. Water treatment by the AC gliding arc air plasma

    Science.gov (United States)

    Gharagozalian, Mehrnaz; Dorranian, Davoud; Ghoranneviss, Mahmood

    2017-06-01

    In this study, the effects of gliding arc (G Arc) plasma system on the treatment of water have been investigated experimentally. An AC power supply of 15 kV potential difference at 50 Hz frequency was employed to generate plasma. Plasma density and temperature were measured using spectroscopic method. The water was contaminated with staphylococcus aureus (Gram-positive) and salmonella bacteria (Gram-negative), and Penicillium (mold fungus) individually. pH, hydrogen peroxide, and nitride contents of treated water were measured after plasma treatment. Decontamination of treated water was determined using colony counting method. Results indicate that G Arc plasma is a powerful and green tool to decontaminate water without producing any byproducts.

  2. Modelling of the arc reattachment process in plasma torches

    Energy Technology Data Exchange (ETDEWEB)

    Trelles, J P; Pfender, E; Heberlein, J V R [Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455 (United States)

    2007-09-21

    The need to improve plasma spraying processes has motivated the development of computational models capable of describing the arc dynamics inside plasma torches. Although progress has been made in the development of such models, the realistic simulation of the arc reattachment process, a central part of the arc dynamics inside plasma torches, is still an unsolved problem. This study presents a reattachment model capable of mimicking the physical reattachment process as part of a local thermodynamic equilibrium description of the plasma flow. The fluid and electromagnetic equations describing the plasma flow are solved in a fully-coupled approach by a variational multi-scale finite element method, which implicitly accounts for the multi-scale nature of the flow. The effectiveness of our modelling approach is demonstrated by simulations of a commercial plasma spraying torch operating with Ar-He under different operating conditions. The model is able to match the experimentally measured peak frequencies of the voltage signal, arc lengths and anode spot sizes, but produces voltage drops exceeding those measured. This finding, added to the apparent lack of a well-defined cold boundary layer all around the arc, points towards the importance of non-equilibrium effects inside the torch, especially in the anode attachment region.

  3. Investigation of Transferred-Arc Cleaning for Thin Film Removal

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, K.; Castro, R.G.; Bartram, B.

    1998-03-17

    Transferred-arc cleaning is being investigated as a precision cleaning method for thin films on electrically conducting substrates as well as the traditional cleaning and roughening pretreatment for LPPS. Transferred-arc cleaning of copper substrates has been studied to identify the effect of processing conditions on cleaning and roughening characteristics. A Box-Behnken response surface design experiment varying the chamber pressure, substrate standoff distance, and torch current while observing the transferred arc voltage, voltage fluctuation, current, emitted light, and surface cleanliness was performed. The result of the analysis show the effect of the various independent variables on the measured responses. Distinct stages in the cleaning process are identified by their sample cleanliness, voltage level, voltage fluctuation, emitted light, and erosion rate.

  4. A highly reliable trigger for vacuum ARC plasma source

    Energy Technology Data Exchange (ETDEWEB)

    Bernardet, H.; Godechot, X.; Jarjat, F. [SODERN, Limeil-Brevannes (France)

    1996-08-01

    The authors have developed a reliable electrical trigger and its associated circuitry to fire vacuum arc plasma or ion source. They tested different embodiments of the trigger device in order to get a highly reliable one, which is able to perform more than 1.2 x 10{sup 6} shots at 60 A and 6.5 ps pulse length. The evolution of the ion current emitted has been recorded as a function of the number of shots. They have also investigated in which direction the plasma jet is emitted : axially or radially. This device can be used to fire a vacuum arc plasma or ion source by plasma injection. It has obvious advantage to be placed outside the cathode and therefore would ease maintenance of vacuum arc devices.

  5. Arc Plasma Gun With Coaxial Powder Feed

    Science.gov (United States)

    Zaplatynsky, Isidor

    1988-01-01

    Redesigned plasma gun provides improved metallic and ceramic coatings. Particles injected directly through coaxial bore in cathode into central region of plasma jet. Introduced into hotter and faster region of plasma jet.

  6. Simple filtered repetitively pulsed vacuum arc plasma source

    Science.gov (United States)

    Chekh, Yu.; Zhirkov, I. S.; Delplancke-Ogletree, M. P.

    2010-02-01

    A very simple design of cathodic filtered vacuum arc plasma source is proposed. The source without filter has only four components and none of them require precise machining. The source operates in a repetitively pulsed regime, and for laboratory experiments it can be used without water cooling. Despite the simple construction, the source provides high ion current at the filter outlet reaching 2.5% of 400 A arc current, revealing stable operation in a wide pressure range from high vacuum to oxygen pressure up to more than 10-2 mbar. There is no need in complicated power supply system for this plasma source, only one power supply can be used to ignite the arc, to provide the current for the arc itself, to generate the magnetic field in the filter, and provide its positive electric biasing without any additional high power resistance.

  7. Arc generation from sputtering plasma-dielectric inclusion interactions

    CERN Document Server

    Wickersham, C E J; Fan, J S

    2002-01-01

    Arcing during sputter deposition and etching is a significant cause of particle defect generation during device fabrication. In this article we report on the effect of aluminum oxide inclusion size, shape, and orientation on the propensity for arcing during sputtering of aluminum targets. The size, shape, and orientation of a dielectric inclusion plays a major role in determining the propensity for arcing and macroparticle emission. In previous studies we found that there is a critical inclusion size required for arcing to occur. In this article we used high-speed videos, electric arc detection, and measurements of particle defect density on wafers to study the effect of Al sub 2 O sub 3 inclusion size, shape, and orientation on arc rate, intensity, and silicon wafer particle defect density. We found that the cross-sectional area of the inclusion exposed to the sputtering plasma is the critical parameter that determines the arc rate and rate of macroparticle emission. Analysis of the arc rate, particle defect...

  8. Effects of electrode properties on transition limit to big-arcs in combustion gas plasma boundary layer. Nensho gas plasma kyokaisonai deno daidenryu kyodai arc hassei genkai ni oyobosu denkyoku bussei no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Okazaki, K.; Okumura, Y. (Tokyo Institute of Technology, Tokyo (Japan)); Kokumai, M.; Yoshikawa, N. (Toyohashi University of Technology, Aichi (Japan))

    1994-05-25

    The effect of physical properties of electrode on the transition from micro-arc to big-arc in the boundary layer of combustion gas plasma such as MHD power generation, the method for preventing the occurrence of big-arc at the electrode surface side, and the possibility of small dispersion of micro-arc are experimentally investigated. The critical current for transition from micro-arc to big-arc is mainly determined by the main part temperature. It is also affected by the electrode properties. This is due to the change in arc shape caused by the heat transfer to the electrode surface and the melting and evaporation of the electrode. In the case of electrode which is likely to give rise to the abrupt gushing of metal vapor, the transition from micro-arc to big-arc is likely to occur because the boundary layer is easily broken as the momentum of the gushing vapor directed rectangularly to the electrode surface which is generating the micro-arc is large. For the prevention of transition from micro-arc to big-arc even at a large current density, it is important to select the electrode material which is characterized by high thermal conductivity, high boiling point, and high latent heat of evaporation. 17 refs., 15 figs., 1 tab.

  9. Shunting arc plasma source for pure carbon ion beam.

    Science.gov (United States)

    Koguchi, H; Sakakita, H; Kiyama, S; Shimada, T; Sato, Y; Hirano, Y

    2012-02-01

    A plasma source is developed using a coaxial shunting arc plasma gun to extract a pure carbon ion beam. The pure carbon ion beam is a new type of deposition system for diamond and other carbon materials. Our plasma device generates pure carbon plasma from solid-state carbon material without using a hydrocarbon gas such as methane gas, and the plasma does not contain any hydrogen. The ion saturation current of the discharge measured by a double probe is about 0.2 mA∕mm(2) at the peak of the pulse.

  10. Shunting arc plasma source for pure carbon ion beama)

    Science.gov (United States)

    Koguchi, H.; Sakakita, H.; Kiyama, S.; Shimada, T.; Sato, Y.; Hirano, Y.

    2012-02-01

    A plasma source is developed using a coaxial shunting arc plasma gun to extract a pure carbon ion beam. The pure carbon ion beam is a new type of deposition system for diamond and other carbon materials. Our plasma device generates pure carbon plasma from solid-state carbon material without using a hydrocarbon gas such as methane gas, and the plasma does not contain any hydrogen. The ion saturation current of the discharge measured by a double probe is about 0.2 mA/mm2 at the peak of the pulse.

  11. Heat Transfer Analysis for Industrial AC Electric Arc Furnace

    Institute of Scientific and Technical Information of China (English)

    (U)nal (C)amdali; Murat Tun(c)

    2005-01-01

    The heat transfer analysis was performed for an AC electric arc furnace (EAF). Heat losses by conduction, convection and radiation from outer surface, roof, bottom and electrodes of EAF were determined in detail. Some suggestions about decreasing heat losses were presented.

  12. Control of arc plasma torches: compensation of operational enthalpy drifts

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, D H; Alexieva, J; Djakov, B E; Enikov, R [Institute of Electronics, Bulgarian Academy of Sciences, 72 Tzarigradsko Chaussee, 1784 Sofia (Bulgaria); Dimitrov, D [Centre of Biomedical Engineering, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl. 105, 1113 Sofia (Bulgaria)], E-mail: dick.oliver@gmail.com

    2008-05-01

    In arc plasma torches electrode wear is the main reason for slow changes in the electrical and thermal torch characteristics. Such effects hinder technological applications of this type of plasma torches whenever the enthalpy must be maintained at a fixed level, or varied as needed. To solve this problem, a new method and algorithm for torch control are proposed. The time evolution of the arc current, voltage and thermal power loss of the torch are recorded. The values measured are used to find the required value of the enthalpy.

  13. Unique variable polarity plasma arc welding for space shuttle

    Science.gov (United States)

    Schwinghamer, R. J.

    1985-01-01

    Since the introduction of the Plasma Arc Torch in 1955 and subsequent to the work at Boeing in the 1960's, significant improvements crucial to success have been made in the Variable Polarity Plasma Arc (VPPA) Process at the Marshall Space Flight Center. Several very important advantages to this process are given, and the genesis of PA welding, the genesis of VPPA welding, special equiment requirements, weld property development, results with other aluminum alloys, and the eventual successful VPPA transition to production operations are discussed.

  14. Plasma Processes : Arc root dynamics in high power plasma torches – Evidence of chaotic behavior

    Indian Academy of Sciences (India)

    A K Das

    2000-11-01

    Although plasma torches have been commercially available for about 50 years, areas such as plasma gun design, process efficiency, reproducibility, plasma stability, torch lives etc. have remained mostly unattended. Recent torch developments have been focusing on the basic understanding of the plasma column and its dynamics inside the plasma torch, the interaction of plasma jet and the powders, the interaction of the plasma jet with surroundings and the impingement of the jet on the substrate. Two of the major causes of erratic and poor performance of a variety of thermal plasma processes are currently identified as the fluctuations arising out of the arc root movement on the electrodes inside the plasma torch and the fluid dynamic instabilities arising out of entrainment of the air into the plasma jet. This paper reviews the current state of understanding of these fluctuations as well as the dynamics of arc root movement in plasma torches. The work done at the author’s laboratory on studying the fluctuations in arc voltage, arc current, acoustic emissions and optical emissions are also presented. These fluctuations are observed to be chaotic and interrelated. Real time monitoring and controlling the arc instabilities through chaos characterization parameters can greatly contribute to the understanding of electrode erosion as well as improvement of plasma torch lifetime.

  15. Arc plasma devices: Evolving mechanical design from numerical simulation

    Indian Academy of Sciences (India)

    S Ghorui; A K Das

    2013-04-01

    Wide ranges of technological applications involve arc plasma devices as the primary plasma source for processing work. Recent findings exhibit the existence of appreciable thermal non-equilibrium in these so-called thermal plasma devices. Commercially available magnetohydrodynamic codes are not capable of handling such systems due to unavailability of non-equilibrium thermodynamic and transport property data and self-consistent models. A recipe for obtaining mechanical design of arc plasma devices from numerical simulation incorporating two-temperature thermal non-equilibrium model is presented in this article with reference to the plasma of the mixture of molecular gases like nitrogen and oxygen. Such systems are technologically important as they correspond to the plasma devices operating with air, oxygen plasma torches in cutting industries and plasma devices using nitrogen as shielding gas. Temperature field, associated fluid dynamics and electrical characteristics of a plasma torch are computed in a systematic manner to evaluate the performance of a conceived design using a two-fluid CFD model coupled with a two-temperature thermodynamic and transport property code. Important effects of different nozzle designs and plasma gases obtained from the formalism are discussed. Non-equilibrium thermo-dynamic properties are computed using modified two-temperature Saha equations and transport properties are computed using standard Chapman–Enskog approach.

  16. Electromagnetic radiation generated by arcing in low density plasma

    Science.gov (United States)

    Vayner, Boris V.; Ferguson, Dale C.; Snyder, David B.; Doreswamy, C. V.

    1996-01-01

    An unavoidable step in the process of space exploration is to use high-power, very large spacecraft launched into Earth orbit. Obviously, the spacecraft will need powerful energy sources. Previous experience has shown that electrical discharges occur on the surfaces of a high-voltage array, and these discharges (arcs) are undesirable in many respects. Moreover, any high voltage conductor will interact with the surrounding plasma, and that interaction may result in electrical discharges between the conductor and plasma (or between two conductors with different potentials, for example, during docking and extravehicular activity). One very important aspect is the generation of electromagnetic radiation by arcing. To prevent the negative influence of electromagnetic noise on the operation of spacecraft systems, it seems necessary to determine the spectra and absolute levels of the radiation, and to determine limitations on the solar array bias voltage that depend on the parameters of LEO plasma and the technical requirements of the spacecraft equipment. This report describes the results of an experimental study and computer simulation of the electromagnetic radiation generated by arcing on spacecraft surfaces. A large set of high quality data was obtained during the Solar Array Module Plasma Interaction Experiment (SAMPIE, flight STS-62) and ground test. These data include the amplitudes of current, pulse forms, duration of each arc, and spectra of plasma waves. A theoretical explanation of the observed features is presented in this report too. The elaborated model allows us to determine the parameters of the electromagnetic noise for different frequency ranges, distances from the arcing site, and distinct kinds of plasma waves.

  17. DC Arc Plasma Disposal of Printed Circuit Board

    Institute of Scientific and Technical Information of China (English)

    黄建军; 施嘉标; 孟月东; 刘正之

    2004-01-01

    A new solid waste disposal technology setup with DC arc plasma is presented. Being different from conventional combustion or burning such as incineration, it is based on a process called controlled high-temperature pyrolysis, the thermal destruction and recovery process. The results of vitrification of the circuit board is presented. The properties of vitrified product including hardness and leaching test results are presented. The final product (vitrified material) and air emission from the plasma treatment is environmentally acceptable.

  18. Hypergravity synthesis of graphitic carbon nanomaterial in glide arc plasma

    NARCIS (Netherlands)

    Šperka, J.; Soucek, P.; van Loon, J.J.W.A.; Dowson, A.; Schwarz, C.; Krause, J.; Butenko, Y.; Kroesen, G.; Kudrle, V.

    2014-01-01

    A nanostructured carbon material was synthesized using a methane/helium glide arc plasma under standard and increased gravity. Material analysis performed on samples collected from an effluent gas filter showed that the deposited material was present in the form of carbon nanoparticles. They

  19. A New Waste Disposal Technology-plasma arc Pyrolysis System

    Institute of Scientific and Technical Information of China (English)

    黄建军; 施嘉标; 梁荣庆; 刘正之

    2003-01-01

    This paper introduces a new waste disposal technology with plasma arc. Being different from conventional combustion or burning such as incineration, it is based on a process called controlled pyrolysis-thermal destruction and recovery process. It has four advantages, they are completely safe, clean, high-energy synthesis gas, non-toxic vitrified slag and metal.

  20. Characterization of Plasma Polymerized Hexamethyldisiloxane Films Prepared by Arc Discharge

    NARCIS (Netherlands)

    Lazauskas, A.; Baltrusaitis, Jonas; Grigaliunas, V.; Jucius, D; Guobiene, A.; Prosycevas, I.; Narmontas, P.

    2014-01-01

    Herein, we present a simple method for fabricating plasma polymerized hexamethyldisiloxane films (pp-HMDSO) possessing superhydrophobic characteristics via arc discharge. The pp-HMDSO films were deposited on a soda–lime–silica float glass using HMDSO monomer vapor as a precursor. A detailed surface

  1. Hypergravity synthesis of graphitic carbon nanomaterial in glide arc plasma

    NARCIS (Netherlands)

    J. Šperka; P. Soucek; J.J.W.A. van Loon; A. Dowson; C. Schwarz; J. Krause; Y. Butenko; G. Kroesen; V. Kudrle

    2014-01-01

    A nanostructured carbon material was synthesized using a methane/helium glide arc plasma under standard and increased gravity. Material analysis performed on samples collected from an effluent gas filter showed that the deposited material was present in the form of carbon nanoparticles. They exhibit

  2. Arc-Plasma Wire Spraying: An Optical Study of Process Phenomenology

    Science.gov (United States)

    Gulyaev, I. P.; Dolmatov, A. V.; Kharlamov, M. Yu.; Gulyaev, P. Yu.; Jordan, V. I.; Krivtsun, I. V.; Korzhyk, V. M.; Demyanov, O. I.

    2015-12-01

    In the present paper, we report on the results of an experimental study of heat- and mass-transfer processes in a Plazer 30-PL-W plasma-jet facility used for arc-plasma wire spraying. Using an original optical diagnostic system, we have studied melting behavior of the metal wire, break up and atomization of liquid metal. For the first time, experimental data on the in-flight velocity and temperature of spray particles in arc-plasma wire spraying were obtained. In spite of moderate particle velocities (about 50 m/s), the obtained steel coatings proved to have a low porosity of 1.5%. While studying the spraying process of tungsten wire, we observed the occurrence of anomalous high-velocity (over 4000 m/s) outbursts ejected from the surface of liquid metal droplets. The nature of such outbursts calls for further study.

  3. Non-Equilibrium Modeling of Arc Plasma Torches

    CERN Document Server

    Trelles, J P; Heberlein, J V R

    2013-01-01

    A two-temperature thermal non-equilibrium model is developed and applied to the three-dimensional and time-dependent simulation of the flow inside a DC arc plasma torch. A detailed comparison of the results of the non-equilibrium model with those of an equilibrium model is presented. The fluid and electromagnetic equations in both models are approximated numerically in a fully-coupled approach by a variational multi-scale finite element method. In contrast to the equilibrium model, the non-equilibrium model did not need a separate reattachment model to produce an arc reattachment process and to limit the magnitude of the total voltage drop and arc length. The non-equilibrium results show large non-equilibrium regions in the plasma - cold-flow interaction region and close to the anode surface. Marked differences in the arc dynamics, especially in the arc reattachment process, and in the magnitudes of the total voltage drop and outlet temperatures and velocities between the models are observed. The non-equilibr...

  4. Non-equilibrium modelling of arc plasma torches

    Energy Technology Data Exchange (ETDEWEB)

    Trelles, J P; Heberlein, J V R; Pfender, E [Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455 (United States)

    2007-10-07

    A two-temperature thermal non-equilibrium model is developed and applied to the three-dimensional and time-dependent simulation of the flow inside a dc arc plasma torch. A detailed comparison of the results of the non-equilibrium model with those of an equilibrium model is presented. The fluid and electromagnetic equations in both models are approximated numerically in a fully-coupled approach by a variational multi-scale finite element method. In contrast to the equilibrium model, the non-equilibrium model did not need a separate reattachment model to produce an arc reattachment process and to limit the magnitude of the total voltage drop and arc length. The non-equilibrium results show large non-equilibrium regions in the plasma-cold-flow interaction region and close to the anode surface. Marked differences in the arc dynamics, especially in the arc reattachment process, and in the magnitudes of the total voltage drop and outlet temperatures and velocities between the models are observed. The non-equilibrium results show improved agreement with experimental observations.

  5. Optimization of a transferred arc reactor for metal nanoparticle synthesis

    Science.gov (United States)

    Stein, Matthias; Kruis, Frank Einar

    2016-09-01

    The demand for metal nanoparticles is increasing strongly. Transferred arc synthesis is a promising process in this respect, as it shows high production rates, good quality particles and the ability of up-scaling. The influence of several process parameters on the performance of the process in terms of production rate and particle size is investigated. These parameters are the electrode design and adjustment, the gas flow rate and power input. A novel feeding mechanism allows process operation over an extended time period. It is shown that the process is capable of producing pure metal nanoparticles with variable primary particle sizes and comparatively high production rates. Optimal process conditions for a single transferred arc electrode pair are found, which allow further scale-up by numbering up.

  6. Note: Triggering behavior of a vacuum arc plasma source.

    Science.gov (United States)

    Lan, C H; Long, J D; Zheng, L; Dong, P; Yang, Z; Li, J; Wang, T; He, J L

    2016-08-01

    Axial symmetry of discharge is very important for application of vacuum arc plasma. It is discovered that the triggering method is a significant factor that would influence the symmetry of arc discharge at the final stable stage. Using high-speed multiframe photography, the transition processes from cathode-trigger discharge to cathode-anode discharge were observed. It is shown that the performances of the two triggering methods investigated are quite different. Arc discharge triggered by independent electric source can be stabilized at the center of anode grid, but it is difficult to achieve such good symmetry through resistance triggering. It is also found that the triggering process is highly correlated to the behavior of emitted electrons.

  7. Note: Triggering behavior of a vacuum arc plasma source

    Energy Technology Data Exchange (ETDEWEB)

    Lan, C. H., E-mail: lanchaohui@163.com; Long, J. D.; Zheng, L.; Dong, P.; Yang, Z.; Li, J.; Wang, T.; He, J. L. [Institute of Fluid Physics, China Academy of Engineering Physics, Mianyang 621900 (China)

    2016-08-15

    Axial symmetry of discharge is very important for application of vacuum arc plasma. It is discovered that the triggering method is a significant factor that would influence the symmetry of arc discharge at the final stable stage. Using high-speed multiframe photography, the transition processes from cathode-trigger discharge to cathode-anode discharge were observed. It is shown that the performances of the two triggering methods investigated are quite different. Arc discharge triggered by independent electric source can be stabilized at the center of anode grid, but it is difficult to achieve such good symmetry through resistance triggering. It is also found that the triggering process is highly correlated to the behavior of emitted electrons.

  8. Generation of low-temperature plasma by low-pressure arcs for synthesis of nitride coatings

    Science.gov (United States)

    Krysina, O. V.; Koval, N. N.; Lopatin, I. V.; Shugurov, V. V.; Kovalsky, S. S.

    2016-01-01

    Experiments were performed to study gas, metal, and mixed metal-gas plasmas. The plasmas were generated with the use of an arc evaporator and a gas-plasma source with a hot filament and hollow cathode that were operated independently or simultaneously. It has been revealed that the arc current of gas-plasma source affects the parameters of the metal-gas plasma and the element concentrations in the coatings. It has been demonstrated that the characteristics of the nitride coatings produced by plasma-assisted vacuum-arc deposition can be controlled by varying the parameters of the arc in the gas-plasma source.

  9. Experimental determination of the weld penetration evolution in keyhole plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    Hu Qingxian; Wu Chuansong; Zhang Yuming

    2007-01-01

    Keyhole plasma arc welding experiments are conducted to measure the weld geometry and penetration at different moments during the initial phase from igniting arc to quasi-steady state. Indirect information on keyhole formation and evolution in plasma arc welding can be extracted based on the weld macrophotograph at cross section. It has laid foundation to verify the mathematical models of keyhole plasma arc welding.

  10. INFLUENCE OF VACUUM ARC PLASMA EVAPORATOR CATHODE GEOMETRY OF ON VALUE OF ADMISSIBLE ARC DISCHARGE CURRENT

    Directory of Open Access Journals (Sweden)

    I. A. Ivanou

    2015-01-01

    Full Text Available An analysis of main design parameters that determine a level of droplet formation intensity at the generating stage of plasma flow has been given in the paper. The paper considers the most widely used designs of water cooled consumable cathodes. Ti or Ti–Si and Fe–Cr alloys have been taken as a material for cathodes. The following calculated data: average ionic charge Zi for titanium plasma +1.6; for «titanium–silicon plasma» +1.2, an electronic discharge 1.6022 ⋅ 10–19 C, an ion velocity vi = 2 ⋅ 104 m/s, an effective volt energy equivalent of heat flow diverted in the cathode Uк = 12 V, temperature of erosion cathode surface Тп = 550 К; temperature of the cooled cathode surface То = 350 К have been accepted in order to determine dependence of a maximum admissible arc discharge current on cathode height. The calculations have been carried out for various values of the cathode heights hк (from 0.02 to 0.05 m. Diameter of a target cathode is equal to 0.08 m for a majority of technological plasma devices, therefore, the area of the erosion surface is S = 0.005 m2.A thickness selection for a consumable target cathode part in the vacuum arc plasma source has been justified in the paper. The thickness ensures formation of minimum drop phase in the plasma flow during arc cathode material evaporation. It has been shown that a maximum admissible current of an arc discharge is practically equal to the minimum current of stable arcing when thickness of the consumable cathode part is equal to 0.05 m. The admissible discharge current can be rather significant and ensure high productivity during coating process with formation of relatively low amount of droplet phase in the coating at small values of hк.

  11. Simulation of the Effects of Several Factors on Arc Plasma Behavior in Low Voltage Circuit Breaker

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Taking into account the properties of the arc plasma and the electromagnetic, heat and radiative phenomena, commercial computational fluid dynamics software PHOENICS has been adapted and modified to develop the three-dimensional magneto-hydrodynamic (MHD)model of arc in a low voltage circuit breaker. The effects of the arc ignition location, venting size and gassing material on arc behavior have been investigated. The analysis of the results show that the arc velocity accelerates with the increase in the distance between arc ignition location and of the venting size, and the existence of the gassing material is beneficial to improving the arc voltage and reducing the arc temperature.

  12. Plasma ARC Welding of High-Performance-Ship Materials

    Science.gov (United States)

    1979-05-01

    the work piece dur- ing welding. During the course of development by industry of the plasma arc process as a welding tool, v&rious orifice...point for the intended keyhole weld although, of course , minor modification to the travel speed may have to be made. The curves may be used to estimate...8217 : ... .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. TABLE 2 - TENSILE TEST RESULTS SpOC imun Ytlld Strounth T’n mil• StrIe lngth I|loniinttirol Lwait IL’ ,i ifr pin

  13. Plasma Spraying of Copper by Hybrid Water-Gas DC Arc Plasma Torch

    Science.gov (United States)

    Kavka, T.; Matějíček, J.; Ctibor, P.; Mašláni, A.; Hrabovský, M.

    2011-06-01

    Water-stabilized DC arc plasma torches offer a good alternative to common plasma sources used for plasma spraying applications. Unique properties of the generated plasma are determined by a specific plasma torch construction. This article is focused on a study of the plasma spraying process performed by a hybrid torch WSP500®-H, which combines two principles of arc stabilization—water vortex and gas flow. Spraying tests with copper powder have been carried out in a wide range of plasma torch parameters. First, analyses of particle in-flight behavior for various spraying conditions were done. After, particles were collected in liquid nitrogen, which enabled analyses of the particle in-flight oxidation. A series of spraying tests were carried out and coatings were analyzed for their microstructure, porosity, oxide content, mechanical, and thermal properties.

  14. Study of coal conversion in an arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Xie, K.C.; Lu, Y.K.; Tian, Y.J.; Wang, D.Z. [Taiyuan University of Technology, Taiyuan (China)

    2002-12-01

    Coal conversion in arc plasma with an initial temperature of 3700 K is complex; a new conversion mechanism is put forward in this article. The functions of pyrolysis and the interaction of active species containing plasma jets are the main factors for coal conversion under these conditions. This study indicates that when the coal feed rate is lower than 2.0 g/s, both pyrolysis and active species have evident contribution to coal conversion; the pyrolysis controls the coal conversion and the function of active species is very weak. It is also found that the coal feed rate has a large influence on coal conversion and the production of gas components.

  15. Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

    Science.gov (United States)

    Zhai, Guofu; Bo, Kai; Chen, Mo; Zhou, Xue; Qiao, Xinlei

    2016-05-01

    Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit. We characterized the arc plasma jet flow appearance at different currents by using high-speed photography, and two polished contacts were used to search for the relationship between roughness and plasma jet flow. Then, to make the nature of arc plasma jet flow phenomena clear, a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated. The simulated DC arc plasma was presented with the temperature distribution and the current density distribution. Furthermore, the calculated arc flow velocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress. The combined action of volume force and contact surface was the main reason of the arc jet flow. supported by National Natural Science Foundation of China (Nos. 51307030, 51277038)

  16. Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

    Institute of Scientific and Technical Information of China (English)

    ZHAI Guofu; BO Kai; CHEN Mo; ZHOU Xue; QIAO Xinlei

    2016-01-01

    Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit.We characterized the arc plasma jet flow appearance at different currents by using high-speed photography,and two polished contacts were used to search for the relationship between roughness and plasma jet flow.Then,to make the nature of arc plasma jet flow phenomena clear,a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated.The simulated DC arc plasma was presented with the temperature distribution and the current density distribution.Furthermore,the calculated arc flow vclocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress.The combined action of volume force and contact surface was the main reason of the arc jet flow.

  17. Gas Tungsten Arc Welding and Plasma Arc Cutting. Teacher Edition [and] Student Edition [and] Student Workbook. Second Edition.

    Science.gov (United States)

    Harper, Eddie; Knapp, John

    This packet of instructional materials for a gas tungsten arc welding (GTAW) and plasma arc cutting course is comprised of a teacher edition, student edition, and student workbook. The teacher edition consists of introductory pages and teacher pages. Introductory pages include training and competency profile, state duty/task crosswalk,…

  18. Characteristics of Single Cathode Cascaded Bias Voltage Arc Plasma

    Science.gov (United States)

    Ou, Wei; Deng, Baiquan; Zeng, Xianjun; Gou, Fujun; Xue, Xiaoyan; Zhang, Weiwei; Cao, Xiaogang; Yang, Dangxiao; Cao, Zhi

    2016-06-01

    A single cathode with a cascaded bias voltage arc plasma source has been developed with a new quartz cathode chamber, instead of the previous copper chambers, to provide better diagnostic observation and access to the plasma optical emission. The cathode chamber cooling scheme is also modified to be naturally cooled only by light emission without cooling water to improve the optical thin performance in the optical path. A single-parameter physical model has been developed to describe the power dissipated in the cascaded bias voltage arc discharge argon plasmas, which have been investigated by utilizing optical emission spectroscopy (OES) and Langmuir probe. In the experiments, discharge currents from 50 A to 100 A, argon flow rates from 800 sccm to 2000 sccm and magnetic fields of 0.1 T and 0.2 T were chosen. The results show: (a) the relationship between the averaged resistivity and the averaged current density exhibits an empirical scaling law as \\barη \\propto \\bar {j}-0.63369 and the power dissipated in the arc has a strong relation with the filling factor; (b) through the quartz, the argon ions optical emission lines have been easily observed and are dominating with wavelengths between 340 nm and 520 nm, which are the emissions of Ar+-434.81 nm and Ar+-442.60 nm line, and the intensities are increasing with the arc current and decreasing with the inlet argon flow rate; and (c) the electron density and temperature can reach 2.0 × 1019 m-3 and 0.48 eV, respectively, under the conditions of an arc current of 90 A and a magnetic field of 0.2 T. The half-width of the ne radial profile is approximatively equal to a few Larmor radii of electrons and can be regarded as the diameter of the plasma jet in the experiments. supported by the International Thermonuclear Experimental Reactor (ITER) Program Special of Ministry of Science and Technology (No. 2013GB114003), and National Natural Science Foundation of China (Nos. 11275135, 11475122)

  19. Analysis of keyhole geometry in plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    Hu Qingxian; Wu Chuansong

    2006-01-01

    The key problem for numerical simulation of plasma arc welding (PAW) process is to develop a suitable and adaptive volumetric heat source mode which reflects the physical characteristics of keyhole PAW. To this end, the keyhole geometry under different PAW process conditions must be predicted. In this paper, a mathematical model for determining the keyhole shape is developed with considering the mass and momentum conservation of the in-keyhole plasma jet as well as the pressure equilibrium at the plasma jet/liquid metal boundary. A suitable heat source model related to the keyhole shape is applied to the calculation of PAW weld dimensions. The predicted results are in good agreement with the experimental ones.

  20. Estimation of dynamic properties of attractors observed in hollow copper electrode atmospheric pressure arc plasma system

    Indian Academy of Sciences (India)

    S Ghorul; S N Sahasrabudhe; P S S Murthy; A K Das; N Venkatramani

    2002-07-01

    Understanding of the basic nature of arc root fluctuation is still one of the unsolved problems in thermal arc plasma physics. It has direct impact on myriads of thermal plasma applications being implemented at present. Recently, chaotic nature of arc root behavior has been reported through the analysis of voltages, acoustic and optical signals which are generated from a hollow copper electrode arc plasma torch. In this paper we present details of computations involved in the estimation process of various dynamic properties and show how they reflect chaotic behavior of arc root in the system.

  1. Formation of carbon deposits from coal in an arc plasma

    Energy Technology Data Exchange (ETDEWEB)

    Wang, B.; Tian, Y.; Zhang, Y.; Zhu, S.; Lu, Y.; Zhang, Y.; Xie, K. [Taiyuan University of Technology, Taiyuan (China)

    2007-07-01

    The issue of deposited carbon (DC) on a reactor wall during the production of acetylene by the coal/arc plasma process is a potential obstacle for the industrialization process. The formation mechanism of DC is very difficult to reveal because the high complexity of coal and the volatile matter. Combining with quenching technique, the methane, liquid petroleum gas and benzene were employed as the model materials to roughly act as the light gas, chain and aromatic subcomponents of volatile matter, and then the reasonable formation mechanism of DC was subtly speculated accordingly.

  2. SENSORING DROPLET SPRAY TRANSFER IN MIG WELDING BASED ON ARC SPECTRUM SIGNAL

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The method to detect droplet transfer by means of arc spectrum, while the experiment sets, testing principle and data processing procedure, are presented. The experiment and analysis results show that arc spectrum signal can be utilized to detect and measure the transfer procedure, the transfer modes and the transfer parameters. The arc spectrum signal enjoys excellent quality with high signal amplitude. Each transfer mode has its specific typical signal mode, and the pulse outline corresponds to an integrated transferring procedure of one droplet. All these features of arc spectrum signal can be easily applied in the control of transfer procedure,the identification and stabilization of transfer mode and the measurement of transfer parameters.

  3. The Main Plasma Chemical Process of Nitric Oxide Production by Arc Discharge%The Main Plasma Chemical Process of Nitric Oxide Production by Arc Discharge

    Institute of Scientific and Technical Information of China (English)

    杨旗; 胡辉; 陈卫鹏; 许杰; 张锦丽; 吴双

    2011-01-01

    By adopting the optical multi-channel analyzer combined with fourier transform infrared (FTIR) spectrometer, the dominant free radicals and products generated by arc discharge were measured and studied, and the main plasma chemical reaction process in the nitric oxide production by arc discharge was identified. Plasma chemical kinetic curves of O, O2, N2, N and NO were simulated by using CHEMKIN and MATLAB. The results show that the main plasma chemical reaction process of nitric oxide production by arc discharge is a replacement reaction between O and N2, where NO can be generated instantaneously when discharging reaches stable.

  4. DC Arc Plasma Furnace Melting of Waste Incinerator Fly Ash

    Institute of Scientific and Technical Information of China (English)

    CHEN Mingzhou; MENG Yuedong; SHI Jiabiao; KUANG Jingan; NI Guohua; LIU Wei; JIANG Yiman

    2009-01-01

    Municipal solid waste incinerator (MSWI) fly ash was melted using a set of direct current (DC) arc plasma furnace system for the first time in China.At a feed-rate of flying ash of 80 kg/h,the temperature at the gas outlet was above 1300℃.Dioxins in the off-gas were recorded as 0.029 ng I-TEQ/Nm3 (international toxic equivalent,I-TEQ),well below 0.5 ng TEQ/Nm3 (toxic equivalent,TEQ),while those in the melted product(slag)were 0.00035 ng/g I-TEQ.Molten slag from the furnace showed excellent resistance against the leaching of heavy metals.These results prove that the plasma furnace is effective for the detoxification and stabilization of MSWI fly ash.

  5. Arc Root Motions in an Argon-Hydrogen Direct-Current Plasma Torch at Reduced Pressure

    Institute of Scientific and Technical Information of China (English)

    HUANG He-Ji; PAN Wen-Xia; WU Cheng-Kang

    2008-01-01

    Arc root motions in generating dc argon hydrogen plasma at reduced pressure are optically observed using a high-speed video camera. The time resolved angular position of the arc root attachment point is measured and analysed. The arc root movement is characterized as a chaotic and jumping motion along the circular direction on the anode surface.

  6. Computer-based sensing and visualizing of metal transfer mode in gas metal arc welding

    Institute of Scientific and Technical Information of China (English)

    Chen Maoai; Wu Chuansong; Lü Yunfei

    2008-01-01

    Using Xenon lamp lights to overcome the strong interference from the welding arc, a computer-based system is developed to sense and visualize the metal transfer in GMAW. This system combines through-the-arc sensing of the welding current and arc voltage with high speed imaging of the metal transfer. It can simultaneously display the metal transfer processes and waveforms of electrical welding parameters in real-time The metal transfer videos and waveforms of electrical welding parameters can be recorded. Metal transfers under various welding conditions have been investigated with the system developed.

  7. The characteristics of arc beam shaping in hybrid plasma and laser deposition manufacturing

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Hai'ou; QIAN; Yingping; WANG; Guilan; ZHENG; Qiguang

    2006-01-01

    As a new direct metal prototyping technology,the hybrid plasma and laser deposition manufacturing (PLDM) is proposed in this paper. In order to figure out the characteristics of plasma arc beam and mould in the PLDM process of high temperature alloy, the high speed CCD camera is used to obtain the picture around the plasma arc. Afterwards the sketch of picture is clearly obtained. And the effect of laser parameter, such as average power, pulse width, pulse repetition frequency and the angle between laser beam and plasma arc beam on the plasma arc appearance, is studied experimentally. The results show that the modality of plasma arc beam is markedly influenced by laser beam. And the improvements of shape precision and surface state of the layer deposited by PLDM are confirmed.

  8. Probe characterization of high-current driven metal plasma in a vacuum-arc rail gun

    Science.gov (United States)

    Vijayan, T.; Roychowdhury, P.; Venkatramani, N.

    2004-10-01

    The characteristics of metal plasma launched by high-current electric arc in a vacuum-arc rail gun are determined by employing electrical and magnetic probes. These measurements are validated by results from theoretical simulations. The arc coupled nonlinear circuit equations are solved simultaneously with the Newtonian arc motion and revealed the undercritically damped behavior of the arc current identical to the arc-current signal recorded by the Rogowski magnetic probe. Similarly the arc velocity and displacement derived from the signatures of B-dot probes are shown to concur closely with the results of J ×B propulsion from simulation. The heating of plasma is formulated in a three-electron population regime with direct arc energy coupling through magnetohydrodynamic, ion-acoustic, Coulomb, and neutral interactions. This results in high temperature (Te) of hundreds of eV in the arc as revealed by the simulation. Hence Te of the rapidly cooling and equilibrating plasma that emerged from the muzzle is high around 80-90eV, which is confirmed by Langmuir electric probe measurements. Density ne of this metal plasma is shown to be in the range 4×1021-6×1021m-3 and includes multiple ion charge states. The exit velocity of the plasma measured by a pair of Langmuir probes is close to 2.2×106cm/s and matched well with the arc velocity determined by the B-dot probes and the results from simulation.

  9. Influence and Analysis of Concentrate Degree of Plasma Arc for Heat Process of Hardening Treatment

    Institute of Scientific and Technical Information of China (English)

    WANG Shuo-gui; YAN Hong-ri

    2004-01-01

    According to the practicable model of the plasma arc surface quench, the influence law of the heat process、cooling course、 temperature field about surface quench treatment by plasma arc due to the concentrate degree of plasma arc heat source are discussed in this paper. It shows that the concentrate degree of plasma arc heat source can change the width of the hardening zone and can not change the maximum harden depth. With the increase of the concentrate degree, the area of the heat influence zone is decreased and its shape is narrowed after the heat source. Relative to cooling rate, the influence of the heat source concentrate degree for heat absorption is bigger. The correctness of the practical model are proved with experimental results for quench hardening of 45# steel by plasma arc.

  10. Influence and Analysis of Concentrate Degree of Plasma Arc for Heat Process of Hardening Treatment

    Institute of Scientific and Technical Information of China (English)

    WANGShuo-gui; YANHong-ri

    2004-01-01

    According to the practicable model of the plasma arc surtace quench, the influence law ot me heat process, cooling course, temperature field about surface quench treatment by plasma arc due to the concentrate degree of plasma arc heat source are discussed in this paper. It shows that the concentrate degree of plasma arc heat source can change the width of the hardening zone and can not change the maximum harden depth. With the increase of the concentrate degree, the area of the heat influence zone is decreased and its shape is narrowed after the heat source. Relative to cooling rate, the influence of the heat source concentrate degree for heat absorption is bigger. The correctness of the practical model are proved with experimental results for quench hardening of 45# steel by plasma arc.

  11. Analysis of plasma characteristics and conductive mechanism of laser assisted pulsed arc welding

    Science.gov (United States)

    Liu, Shuangyu; Chen, Shixian; Wang, Qinghua; Li, Yanqing; Zhang, Hong; Ding, Hongtao

    2017-05-01

    This study aims to investigate the arc plasma shape and the spectral characteristics during the laser assisted pulsed arc welding process. The arc plasma shape was synchronously observed using a high speed camera, and the emission spectrum of plasma was obtained by spectrometer. The well-known Boltzmann plot method and Stark broadening were used to calculate the electron temperature and density respectively. The conductive mechanism of arc ignition in laser assisted arc hybrid welding was investigated, and it was found that the plasma current moved to the arc anode under the action of electric field. Thus, a significant parabolic channel was formed between the keyhole and the wire tip. This channel became the main method of energy transformation between the arc and the molten pool. The calculation results of plasma resistivity show that the laser plasma has low resistivity as the starting point of conductive channel formation. When the laser pulse duration increases, the intensity of the plasma radiation spectrum and the plasma electron density will increase, and the electron temperature will decrease.

  12. Characterization of an atmospheric double arc argon-nitrogen plasma source

    Science.gov (United States)

    Tu, X.; Chéron, B. G.; Yan, J. H.; Yu, L.; Cen, K. F.

    2008-05-01

    In the framework of studies devoted to hazardous waste destruction, an original dc double anode plasma torch has been designed and tested, which produces an elongated, weak fluctuation and reproducible plasma jet at atmospheric pressure. The arc instabilities and dynamic behavior of the double arc argon-nitrogen plasma jet are investigated through the oscillations of electrical signals by combined means of fast Fourier transform and Wigner distribution. In our experiment, the restrike mode is identified as the typical fluctuation behavior in an argon-nitrogen plasma jet. The Fourier spectra and Wigner distributions exhibit two characteristic frequencies of 150 Hz and 4.1 kHz, which reveals that the nature of fluctuations in the double arc argon-nitrogen plasma can be ascribed to the undulation of the power supply and both arc roots motion on the anode channels. In addition, the microscopic properties of the plasma jet inside and outside the arc chamber are investigated by means of optical emission spectroscopy, which yields excitation, electronic, rotational, and vibrational temperatures, as well as the electron number density. The results allow us to examine the validity criteria of a local thermodynamic equilibrium (LTE) state in the plasma arc. The measured electron densities are in good agreement with those calculated from the LTE model, which indicates that the atmospheric double arc argon-nitrogen plasma in the core region is close to the LTE state under our experimental conditions.

  13. Simplification of the Plasma Load of Negative-Pulse-Bias Source Used in Arc Ion Plating

    Institute of Scientific and Technical Information of China (English)

    Dong QI; Ninghui WANG; Guoqiang LIN; Zhenfeng DING

    2003-01-01

    Based on the voltage and current fluctuating phenomenon in the arc plasma load under the negative-pulse-bias, usingthe plasma physics theory and analysis of computer simulation expatiates that the nature of plasma load in vacuumarc plasma is a capacitance

  14. Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis

    Directory of Open Access Journals (Sweden)

    Grzegorz Raniszewski

    2017-02-01

    Full Text Available One of the most common methods of carbon nanotubes (CNTs synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon–plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs. It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented.

  15. The evolution of ion charge states in cathodic vacuum arc plasmas: a review

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre

    2011-12-18

    Cathodic vacuum arc plasmas are known to contain multiply charged ions. 20 years after “Pressure Ionization: its role in metal vapour vacuum arc plasmas and ion sources” appeared in vol. 1 of Plasma Sources Science and Technology, it is a great opportunity to re-visit the issue of pressure ionization, a non-ideal plasma effect, and put it in perspective to the many other factors that influence observable charge state distributions, such as the role of the cathode material, the path in the density-temperature phase diagram, the “noise” in vacuum arc plasma as described by a fractal model approach, the effects of external magnetic fields and charge exchange collisions with neutrals. A much more complex image of the vacuum arc plasma emerges putting decades of experimentation and modeling in perspective.

  16. Generation of intense plasma jets and microparticle beams by an arc in a supersonic vortex

    Science.gov (United States)

    Winterberg, F.

    1990-04-01

    Temperatures up to 50000 have been reached in water vortex stabilized Gerdien arcs. In arcs confined within the cores of supersonic hydrogen vortices much higher temperatures should be possible. Furthermore if these arcs are thermally insulated by a strong magnetic field temperatures up to a 106 K may be attainable. At these temperatures and in passing through a Laval nozzle the arc plasma can reach jet velocities of 100km/sec. If small quantities of heavy elements are entrained by this high velocity plasma jet these heavy elements are carried along reaching the same speed and upon condensation can form beams of clusters and microparticles.

  17. Decomposition of toluene in a gliding arc discharge plasma reactor

    Energy Technology Data Exchange (ETDEWEB)

    Du Changming [School of Environmental Science and Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Yan Jianhua [Institute for Thermal Power Engineering, Zhejiang University, Hangzhou 310027 (China); Cheron, Bruno [UMR 6614 (CORIA), University of Rouen, 76821 Mont Saint Aignan (France)

    2007-11-15

    The decomposition of toluene in a gliding arc discharge (glidarc) was performed and studied. Experimental results indicate that the glidarc technology can effectively decompose toluene molecules and has bright prospects of being applied as an alternative tool to decompose volatile organic compounds. It is found that a change in the electrode material had an insignificant effect on the toluene removal efficiency. The toluene removal efficiency increases with increasing inlet gas temperature. The water vapor present in the gas mixture has a favorable effect on the toluene decomposition in the plasma. The energy efficiency is 29.46 g (kWh{sup -1}) at a relative humidity of 50% and a specific energy input of 0.26 kWh m{sup -3}, which is higher than other types of non-thermal plasmas. Too much or too little oxygen content does not favor toluene decomposition. The major gas phase products detected by FT-IR from the decomposition of toluene with air participation were CO, CO{sub 2}, H{sub 2}O and NO{sub 2}. Some brown depositions were found on the surface of the electrodes, which were polar oxygenous and nitrogenous compounds determined by the GC-MS analysis, such as benzaldehyde, benzoic acid, quinine and nitrophenol from the reaction of toluene with radicals. A possible mechanism for toluene destruction via glidarc technology is proposed and summarized.

  18. Comparative study on interactions between laser and arc plasma during laser-GTA welding and laser-GMA welding

    Science.gov (United States)

    Chen, Minghua; Xu, Jiannan; Xin, Lijun; Zhao, Zuofu; Wu, Fufa

    2016-10-01

    This paper describes an investigation on differences in interactions between laser and arc plasma during laser-gas tungsten arc (LT) welding and laser-gas metal arc (LM) welding. The characteristics of LT heat source and LM heat source, such as plasma behavior, heat penetration ability and spectral information were comparably studied. Based on the plasma discharge theory, the interactions during plasma discharge were modeled and analyzed. Results show that in both LT and LM welding, coupling discharge between the laser keyhole plasma and arc happens, which strongly enhance the arc. But, the enhancing effect in LT welding is much more sensitive than that in LM welding when parameters are adjusted.

  19. Expanding sheath in a bounded plasma in the context of the post-arc phase of a vacuum arc

    Energy Technology Data Exchange (ETDEWEB)

    Sarrailh, P [LAboratoire PLAsma et Conversion de l' Energie (LAPLACE), UMR5213, Universite Paul Sabatier, bat. 3R2, 118 route de Narbonne, 31062 Toulouse cedex 4 (France); Garrigues, L [LAboratoire PLAsma et Conversion de l' Energie (LAPLACE), UMR5213, Universite Paul Sabatier, bat. 3R2, 118 route de Narbonne, 31062 Toulouse cedex 4 (France); Hagelaar, G J M [LAboratoire PLAsma et Conversion de l' Energie (LAPLACE), UMR5213, Universite Paul Sabatier, bat. 3R2, 118 route de Narbonne, 31062 Toulouse cedex 4 (France); Sandolache, G [Schneider Electric Centre de Recherche, 38 TEC, 38050 Grenoble Cedex 09 (France); Rowe, S [Schneider Electric Centre de Recherche, 38 TEC, 38050 Grenoble Cedex 09 (France); Jusselin, B [Schneider Electric Centre de Recherche, 38 TEC, 38050 Grenoble Cedex 09 (France); Boeuf, J P [LAboratoire PLAsma et Conversion de l' Energie (LAPLACE), UMR5213, Universite Paul Sabatier, bat. 3R2, 118 route de Narbonne, 31062 Toulouse cedex 4 (France)

    2008-01-07

    A numerical model of sheath expansion and plasma decay in a bounded plasma subjected to a linearly increasing voltage has been developed. Numerical results obtained with a hybrid-MB model (Maxwell-Boltzmann electrons, particle ions and Poisson's equations) are compared with analytical theory and results from particle-in-cell (PIC) simulations. The hybrid-MB model is similar to models used for plasma immersion ion implantation except that plasma decay due to particle losses to the electrodes is taken into account. The comparisons with more accurate and much more time consuming PIC models show that the hybrid-MB model provides a very satisfactory description of the sheath expansion and plasma decay even for conditions where the grid spacing is much larger than the Debye length. The model is used for high plasma density conditions, corresponding to the post-arc phase of a vacuum arc circuit breaker where a vacuum gap is subject to a transient recovery voltage (TRV) after it has ceased to sustain a vacuum arc. The results show that the plasma sheath expansion is subsonic under these conditions, and that the plasma starts to decay exponentially after two rarefaction waves from the cathode and anode merge in the centre of the gap. A parametric study also shows the strong influence of the TRV rise rate and initial plasma density on the plasma decay time and on the ion current collected by each electrode. The effect of collisions between charged particles and metal atoms resulting for the electrode evaporation is also discussed.

  20. Reforming of biogas to synthesis gas by a rotating arc plasma at atmospheric pressure

    Science.gov (United States)

    Chung, Woo-Jae; Park, Hyun-Woo; Liu, Jing-Lin; Park, Dong-Wha

    2015-09-01

    In order to produce synthesis gas, reforming of biogas composed with 60 percent for CH4 and 40 percent for CO2 was performed by a novel rotating arc plasma process. The effect of O2/CH4 ratio on the conversion, syngas composition and energy cost was investigated to evaluate the performance of proposed system compared with conventional gliding arc plasma process. When the O2/CH4 ratio was increased from 0.4 to 0.9, the conversions of CH4 and O2 increased up to 97.5 percent and 98.8 percent, respectively, while CO2 conversion was almost constant to be 38.6 percent. This is due to more enhance the partial oxidation of CH4 to CO and H2 than that of dry reforming by increasing the O2/CH4 ratio. In this work, energy cost of 32 kJ/mol was achieved with high syngas composition of 71 percent using pure O2 as oxidant reactant. These are lower than those of different arc plasma processes (energy cost of 122 - 1870 kJ/mol) such as spark, spark-shade and gliding arc plasma. Because, this rotating arc plasma can remain in a long arc length and a large volume of plasma with constant arc length mode.

  1. Exfoliation of the tungsten fibreform nanostructure by unipolar arcing in the LHD divertor plasma

    Science.gov (United States)

    Tokitani, M.; Kajita, S.; Masuzaki, S.; Hirahata, Y.; Ohno, N.; Tanabe, T.; LHD Experiment Group

    2011-10-01

    The tungsten nanostructure (W-fuzz) created in the linear divertor simulator (NAGDIS) was exposed to the Large Helical Device (LHD) divertor plasma for only 2 s (1 shot) to study exfoliation/erosion and microscopic modifications due to the high heat/particle loading under high magnetic field conditions. Very fine and randomly moved unipolar arc trails were clearly observed on about half of the W-fuzz area (6 × 10 mm2). The fuzzy surface was exfoliated by continuously moving arc spots even for the very short exposure time. This is the first observation of unipolar arcing and exfoliation of some areas of the W-fuzz structure itself in a large plasma confinement device with a high magnetic field. The typical width and depth of each arc trail were about 8 µm and 1 µm, respectively, and the arc spots moved randomly on the micrometre scale. The fractality of the arc trails was analysed using a box-counting method, and the fractal dimension (D) of the arc trails was estimated to be D ≈ 1.922. This value indicated that the arc spots moved in Brownian motion, and were scarcely influenced by the magnetic field. One should note that such a large scale exfoliation due to unipolar arcing may enhance the surface erosion of the tungsten armour and act as a serious impurity source for fusion plasmas.

  2. CO2 conversion in a gliding arc plasma: 1D cylindrical discharge model

    Science.gov (United States)

    Wang, Weizong; Berthelot, Antonin; Kolev, Stanimir; Tu, Xin; Bogaerts, Annemie

    2016-12-01

    CO2 conversion by a gliding arc plasma is gaining increasing interest, but the underlying mechanisms for an energy-efficient process are still far from understood. Indeed, the chemical complexity of the non-equilibrium plasma poses a challenge for plasma modeling due to the huge computational load. In this paper, a one-dimensional (1D) gliding arc model is developed in a cylindrical frame, with a detailed non-equilibrium CO2 plasma chemistry set, including the CO2 vibrational kinetics up to the dissociation limit. The model solves a set of time-dependent continuity equations based on the chemical reactions, as well as the electron energy balance equation, and it assumes quasi-neutrality in the plasma. The loss of plasma species and heat due to convection by the transverse gas flow is accounted for by using a characteristic frequency of convective cooling, which depends on the gliding arc radius, the relative velocity of the gas flow with respect to the arc and on the arc elongation rate. The calculated values for plasma density and plasma temperature within this work are comparable with experimental data on gliding arc plasma reactors in the literature. Our calculation results indicate that excitation to the vibrational levels promotes efficient dissociation in the gliding arc, and this is consistent with experimental investigations of the gliding arc based CO2 conversion in the literature. Additionally, the dissociation of CO2 through collisions with O atoms has the largest contribution to CO2 splitting under the conditions studied. In addition to the above results, we also demonstrate that lumping the CO2 vibrational states can bring a significant reduction of the computational load. The latter opens up the way for 2D or 3D models with an accurate description of the CO2 vibrational kinetics.

  3. Life cycle cost analysis for the Plasma Arc Furnace

    Energy Technology Data Exchange (ETDEWEB)

    Barnes-Smith, P.

    1994-03-01

    This document is a draft version. The Mixed Waste Integrated Program requested that the Systems Analysis Group investigate the cost effectiveness of using the Plasma Arc Furnace (PAF) module in place of specified thermal and final forms treatment equipment in the baseline Mixed Waste Treatment Project (MWTP) study as performed by Bechtel Corporation, September 1992. The attached estimates are based on the process equipment and facilities cost data contained in the Bechtel study. The PAF process equipment and facilities cost data were developed using independent cost estimates for the equipment list provided by SAIC, Waste Management and Technology Division, in cooperation with the Pollution Prevention and Systems Analysis Group of the Oak Ridge National Laboratory, Chemical Technology Division. In order to develop the total life cycle cost estimate comparison for this study, it was necessary to use a common base for comparison. Although it was felt that the Bechtel MWTP study did not fully reflect the optimum size for the thermal and final forms treatment equipment, it was the best available data at the time.

  4. Experiments in chondrule formation: simulations of gas-grain collisions using plasma arcs

    OpenAIRE

    Morlock, Andreas; Sutton, Yvonne; Braithwaite, Nicholas St.J.; Grady, M.M.

    2010-01-01

    To investigate the formation of chondrules in gas-grain collisions, we conducted experiments where mineral mixtures were melted in plasma arcs. First results already show silicate-rich spheres quite similar to chondrules.

  5. Closed-loop control of weld penetration in keyhole plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    陈强; 孙振国; 孙久文; 王耀文

    2004-01-01

    To improve the penetrating ability and the welding quality of keyhole plasma arc welding, a novel penetration closed-loop control system was established. In the system, welding current and plasma gas flow rate were selected as adjusting variables. The wavelet method was used to detect penetration status from welding arc voltage in real-time. The control strategy of one-keyhole-per-pulse was adapted to fulfill stable and high quality welding process. Experimental results show that the developed system can apparently increase the penetrating force of plasma arc and keyhole plasma arc welding is realized successfully in stainless steel with 10 mm in thickness. Moreover,the disturbances of gradual change and break change from 3 mm to 6 mm in thickness are come over due to the good response property of the developed system.

  6. Formation of Multicharged Metal Ions in Vacuum Arc Plasma Heated by Gyrotron Radiation%Formation of Multicharged Metal Ions in Vacuum Arc Plasma Heated by Gyrotron Radiation

    Institute of Scientific and Technical Information of China (English)

    G. Yu. YUSHKOV; K. P. SAVKIN; A. G. NIKOLAEV; E. M. OKS; A.V. VODOPYANOV; I. V. IZOTOV; D. A. MANSFELD

    2011-01-01

    A new method for the generation of high charged state metal ion beams is developed. This method is based on microwave heating of vacuum arc plasma in a magnetic trap under electron cyclotron resonance (ECR) conditions. Two gyrotrons for plasma heating were used, which were with the following parameters. The first is with a wave frequency of 37.5 GHz, a pulse duration of 1 ms and power of 100 kW, another is with 75 GHz, 0.15 ms and 400 kW. Two different magnetic traps were considered for vacuum arc plasma confinement. The first one is a simple mirror trap. Such system was already investigated and could provide high charge state ions. The second trap was with a cusp magnetic field configuration with native "minimum-B" field structure. Two different ways of metal plasma injection into the magnetic trap were used. The first one is an axial injection from an arc source located out of the trap, and the second is a radial injection from four arc sources mounted at the center of the trap. Both traps provide up to 200 eMA of ion beam current for platinum ions with highest charge state 10+. Ion beams were successfully extracted from the plasma and accelerated by a voltage of up to 20 kV.

  7. CO2 laser-micro plasma arc hybrid welding for galvanized steel sheets

    Institute of Scientific and Technical Information of China (English)

    C. H. KIM; Y. N. AHN; J. H. KIM

    2011-01-01

    A laser lap welding process for zinc-coated steel has a well-known unsolved problem-porosity formation. The boiling temperature of coated zinc is lower than the melting temperature of the base metal. which is steel. In the autogenous laser welding,the zinc vapor generates from the lapped surfaces expels the molten pool and the expulsion causes numerous weld defects, such as spatters and blow holes on the weld surface and porosity inside the welds. The laser-arc hybrid welding was suggested as an alternative method for the laser lap welding because the arc can preheat or post-heat the weldment according to the arrangement of the laser beam and the arc. CO2 laser-micro plasma hybrid welding was applied to the lap welding of zinc-coated steel with zero-gap.The relationships among the weld quality and process parameters of the laser-arc arrangement, and the laser-arc interspacing distance and arc current were investigated using a full-factorial experimental design. The effect of laser-arc arrangement is dominant because the leading plasma arc partially melts the upper steel sheets and vaporizes or oxidizes the coated zinc on the lapped surfaces.Compared with the result from the laser-TIG hybrid welding, the heat input from arc can be reduced by 40%.

  8. Spatial and temporal characteristics of a vacuum-arc rail-gun plasma

    Science.gov (United States)

    Roychowdhury, P.; Vijayan, T.; Iyengar, S. T.

    1997-08-01

    The dynamics of a vacuum-arc operated rail-gun plasma were numerically simulated for the undercritically damped regime and confirmed in experiments. Analytical solutions of arc current, its velocity, and position also showed good agreement with the results. The spatial development of the arc is shown here to follow a linear behavior, even though the propulsion velocity followed an exponential-step function due to the sinusoidal nature of the arc current. Peak arc current ˜100 kA, 15 μs period was propelled to ˜106 cm/s as indicated in time-of-flight measurements and simulations. The voltage signal induced on a B-dot probe by the dynamic sinusoidal arc was simulated, which compared well with the measured probe signal. A Gaussian current distribution inside the measured arc length ˜1-2 cm, was established by unfolding the B-dot probe signal. A peak magnetic field of the order 1-5 kG was also interpreted inside the arc. The emerging plasma contained ion current over tens of amperes in the pulse duration encompassing the arc envelope.

  9. Plasma Arc Cutting Dimensional Accuracy Optimization employing the Parameter Design approach

    Directory of Open Access Journals (Sweden)

    Kechagias John

    2017-01-01

    Full Text Available Plasma Arc Cutting (PAC is a thermal manufacturing process used for metal plates cutting. This work experimentally investigates the influence of process parameters onto the dimensional accuracy performance of the plasma arc cutting process. The cutting parameters studied were cutting speed (mm/min, torch standoff distance (mm, and arc voltage (volts. Linear dimensions of a rectangular workpiece were measured after PAC cutting following the full factorial design experimental approach. For each one of the three process parameters, three parameter levels were used. Analysis of means (ANOM and analysis of variances (ANOVA were performed in order for the effect of each parameter on the leaner dimensional accuracy to be assessed.

  10. Understanding plasma spraying process and characteristics of DC-arc plasma gun (PJ-100

    Directory of Open Access Journals (Sweden)

    Jovana Ružić

    2012-12-01

    Full Text Available The thermal spray processes are a group of coating processes used to apply metallic or non-metallic coatings. In these processes energy sources are used to heat the coating material (in the form of powder, wire, or rod form to a molten or semi-molten state and accelerated towards a prepared surface by either carrier gases or atomization jets. In plasma spraying process, the spraying material is generally in the form of powder and requires a carrier gas to feed the powder into the plasma jet, which is passing between the hot cathode and the cylindrical nozzle-shaped anode. The design of DC plasma gun (PJ - 100 is designed and manufactured in Serbia. Plasma spaying process, the powder injection with the heat, momentum and mass transfers between particles and plasma jet, and the latest developments related to the production of DC plasma gun are described in this article.

  11. Mixed Wastes Vitrification by Transferred Plasma

    Institute of Scientific and Technical Information of China (English)

    J.TAPIA-FABELA; G.ZlSSIS; M.PACHECO-PACHECO; J.PACHECO-SOTELO; C.TORRES-REYES; R.VALDIVIA-BARRIENTOS; J.BENITEZ-READ; R.LOPEZ-CALLEJAS; F.RAMOS-FLORES; S.BOSHLE

    2007-01-01

    Thermal plasma technology provides a stable and long term treatment of mixed wastes through vitrification processes.In this work,a transferred plasma system was realized to vitrify mixed wastes,taking advantage of its high power density,enthalpy and chemical reactivity as well as its rapid quenching and high operation temperatures.To characterize the plasma discharge,a temperature diagnostic is realized by means of optical emission spectroscopy (OES).To typify the morphological structure of the wastes samples,scanning electron microscopy (SEM),and X-ray diffraction (XRD) techniques were applied before and after the plasma treatment.

  12. Contribution to the 3D time-dependent modeling of the arc dynamic behavior in a DC plasma spray torch; Contribution a la modelisation instationnaire et tridimensionnelle du comportement dynamique de l'arc dans une torche de projection plasma

    Energy Technology Data Exchange (ETDEWEB)

    Baudry, C

    2003-11-15

    This work is devoted to the tri-dimensional time-dependent modeling of the arc behavior in a plasma spray torch. It has been carried out in the fame of a collaboration with the Thermal Spray Laboratory of CEA-DAM, Le Ripault and the laboratory of Fluid Mechanics and Heat Transfers of EDF. After a summary of the operation modes of a DC plasma torch and the effect of anode erosion on the torch working, the structure of an electric arc is depicted as well as the main models of non-transferred electric arcs proposed in the literature. This review allows the determination of the main assumption and boundary conditions for a 'realistic' model of the electric arc. Then, the equations, assumptions and boundary conditions of the model we have developed are presented and, the CFD code ESTET 3.4 used to solve the model equations. The model is based on a specific value of the local electric field to predict the breakdown of the arc while its re-striking is favored by a hot gas column at the spot where the highest value of the electric field is calculated. This model gives a realistic prediction of the time-dependent arc behavior according to the plasma-forming gas nature and of the temperature and velocity of the gas flow at the nozzle exit. However, it overestimates the torch voltage and dimensions of the anode arc root attachment spot. (author)

  13. Boosting persistence time of laser-induced plasma by electric arc discharge for optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Eschlböck-Fuchs, S., E-mail: simon.eschlboeck-fuchs@jku.at [Christian Doppler Laboratory for Laser-Assisted Diagnostics, Institute of Applied Physics, Johannes Kepler University Linz, A-4040 Linz (Austria); Kolmhofer, P.J.; Bodea, M.A.; Hechenberger, J.G.; Huber, N. [Christian Doppler Laboratory for Laser-Assisted Diagnostics, Institute of Applied Physics, Johannes Kepler University Linz, A-4040 Linz (Austria); Rössler, R. [voestalpine Stahl GmbH, A-4031 Linz (Austria); Pedarnig, J.D., E-mail: johannes.pedarnig@jku.at [Christian Doppler Laboratory for Laser-Assisted Diagnostics, Institute of Applied Physics, Johannes Kepler University Linz, A-4040 Linz (Austria)

    2015-07-01

    Plasma induced by nanosecond laser ablation is re-excited by a pulsed electric discharge and the parameters and optical emission of the plasma are measured. The discharge is a low-voltage and high-current electric arc that is triggered by the laser-induced plasma and slowly decaying with time. The optical emission of such combined plasma lasts up to several milliseconds which is much longer than without re-excitation (μs range). The emission spectra of re-excited plasma measured on different sample materials show higher line intensities than spectra measured by conventional laser-induced breakdown spectroscopy (LIBS). Moreover, emission lines of fluorine (spectral range 683–691 nm) and sulfur (range 520–550 nm) not detected by conventional LIBS become easily detectable with the combined plasma. The concentration of major components in metallurgical slags, as determined by calibration-free LIBS, agrees very well to the reference data evaluating the spectra taken from re-excited plasma. - Highlights: • Persistence time of laser-induced plasma in air is increased from ~ 10 μs to ~ 1 ms. • Laser-induced plasma triggers an electric arc discharge that boosts the plasma. • The combined laser-arc plasma is in LTE state over very long time (ms range). • CF-LIBS method delivers accurate results evaluating spectra of combined plasma. • Emission from S and F, not detected by LIBS, is detected with combined plasma.

  14. Influence of Plasma Temperature on the Concentration of NO Produced by Pulsed Arc Discharge

    Institute of Scientific and Technical Information of China (English)

    胡辉; 陈卫鹏; 张锦丽; 陆僖; 何俊佳

    2012-01-01

    This study conducted experiments on producing inhaled medical nitric oxide (iNO) by pulsed arc discharge in dry and clean air under different discharge current. The concentration of NO and NO2 produced by air discharge, as well as the change of the ratio of NO2/NO under different discharge current were investigated. Through the analysis of plasma emission spectrum, the relationship between discharge current and arc plasma temperature was studied. The results indicate that, as discharge current increases, the arc plasma temperature increases, which then leads to the increase of NO concentration, the decrease of NO2 concentration, and the rapid decrease of the ratio of NO2/NO. When the plasma temperature is 9000 K, the ratio of NO2/NO is approximately 60%, while when the plasma temperature varies between 10550 K and 11300 K, the NO2/NO ratio is within the range of 4.2% to 4.6%.

  15. Prediction of the cathodic arc root behaviour in a hollow cathode thermal plasma torch

    Energy Technology Data Exchange (ETDEWEB)

    Freton, Pierre; Gonzalez, Jean-Jacques; Escalier, Gaelle, E-mail: pierre.freton@laplace.univ-tlse.f [Universite de Toulouse, UPS, INPT, LAPLACE (Laboratoire Plasma et Conversion d' Energie), 118 route de Narbonne, F-31062 Toulouse cedex 9 (France)

    2009-10-07

    The upper part of a well type cathode (WTC) plasma torch is modelled for several conditions in an air medium in the presence of an electric arc. The plasma flow created by the electric arc is described and the results compared with the data from the literature. Special attention is paid to the description of arc root attachment and to its movement due to the balance of forces. A fine description of the magnetic field produced by the external solenoid is reported. The model is based on the Fluent software implemented with specific developments to be adapted to the thermal plasma domain. The paper shows the necessity to provide an accurate description of the external magnetic field due to the strong influence of the radial magnetic field component. Overall, we propose an original approach for arc root movement description which contributes to the understanding of the flow behaviour in the WTC torch.

  16. Influence of longitudinal magnetic field on metal transfer in MIG arc welding

    Institute of Scientific and Technical Information of China (English)

    Chang Yunlong; Che Xiaoping; He Youyou; Hu Guangxu

    2008-01-01

    Metal transfer is an important phenomenon in metal inert gas (MIG) arc welding with longitudinal alternating magnetic field. It is of great significance to observe the metal transfer modes under different excitatory currents and frequencies. However, it is very difficult to view the metal transfer process directly during welding, due to the strong interference from the arc light. To obtain the relationship between the metal transfer modes and the different magnetic fields, a high-speed video camera was used to acquire the images of globules. Different metal transfer modes under the conditions of different magnetic fields and welding parameters were studied. The experiment shows clear images of droplet transfer as well as influence of longitudinal magnetic field on both metal transfer and globule shape.

  17. Plasma effects in high frequency radiative transfer

    Science.gov (United States)

    Alonso, C. T.

    1981-02-01

    A survey of collective plasma processes which can affect the transfer of high frequency radiation in a hot dense plasma is given. For pedagogical reasons plasma processes are examined by relating them to a particular reference plasma which consists of fully ionized carbon at a temperature kT = 1 KeV (ten million degrees Kelvin) and an electron density N = 3 x 10 to the 23rd power/cu cm, (which corresponds to a mass density rho = 1 gm/cu cm) and an ion density N sub i = 5 x 10 to the 22nd power/cu cm. The transport of photons, ranging from 1 eV to 1 KeV in energy, in such plasmas is considered. Such photons are to be used as diagnostic probes of hot dense laboratory plasmas.

  18. Dusty plasma liquid: structure and transfer phenomena

    Energy Technology Data Exchange (ETDEWEB)

    Fortov, Vladimir E; Vaulina, Olga S; Petrov, Oleg F [Institute for High Energy Densities, Russian Academy of Sciences, Izhorskaya 13/19, Moscow (Russian Federation)

    2005-12-15

    Results are given of the experimental investigation of three-particle correlation for liquid plasma-dust structures formed in the electrode layer of a capacitive rf discharge. The obtained three-particle correlation functions for experimental and numerical data are analysed and compared with the superposition approximation. The forming of clusters of macroparticles in plasma-dust systems being analysed is revealed. The experiments in heat transfer were performed in plasma of a capacitive radio-frequency (rf) discharge in argon (P {approx} 20 Pa) with particles 4 {mu}m in mean diameter. The results are given of an experimental investigation of processes of heat transfer for fluid dust structures in rf-discharge. The analysis of steady-state, and unsteady-state heat transfer are used to obtain the thermal conductivity and diffusivity constants.

  19. Controlling synthesis of carbon nanostructures by plasma means in arc discharge

    Science.gov (United States)

    Volotskova, Olga; Shashurin, Alexey; Torrey, Jon; Raitses, Yevgeny; Keidar, Michael

    2009-11-01

    Thermal stability of SWNTs at conditions of atmospheric arc is crucial for determination of region of their synthesis in arc and in general for clarification of the thermal regime of SWNT in arc plasmas. We investigated electrical resistance dependence on temperature of mats of SWNTs under variable pressures in helium atmosphere, in the air and in vacuum in high temperature ranges (300-1200K) which closely mimic conditions during the synthesis in arc discharge. Dependence of SWNT resistance on temperature exhibits similar ``V-shape'' behavior for all applied conditions which characterized by two temperatures: Tmin (temperature of the minimum of resistance) and Tcr (temperature of destruction of SWNT bundles). It is found that Tmin and Tcr increased with helium pressure, so that at 500 Torr Tcr was 1100K, while Tmin -900K. This is the temperature that corresponds to buffer region between the arc plasma and helium background in arc discharge. Based on that it can be suggested that region of formation of SWNTs in arc should be close to arc periphery. Our study also demonstrates a strong effect of electric and magnetic fields on properties and growth conditions of SWNTs and other carbon nanostructures such as graphene. These effects are quantified by variety of diagnostics tools: SEM, TEM, AFM - microcopies, TGA, RAMAN and UV-vis-NIR.

  20. New perspectives on the dynamics of AC and DC plasma arcs exposed to cross-fields

    Science.gov (United States)

    Abdo, Youssef; Rohani, Vandad; Cauneau, François; Fulcheri, Laurent

    2017-02-01

    Interactions between an arc and external fields are crucially important for the design and the optimization of modern plasma torches. Multiple studies have been conducted to help better understand the behavior of DC and AC current arcs exposed to external and ‘self-induced’ magnetic fields, but the theoretical foundations remain very poorly explored. An analytical investigation has therefore been carried out in order to study the general behavior of DC and AC arcs under the effect of random cross-fields. A simple differential equation describing the general behavior of a planar DC or AC arc has been obtained. Several dimensionless numbers that depend primarily on arc and field parameters and the main arc characteristics (temperature, electric field strength) have also been determined. Their magnitude indicates the general tendency pattern of the arc evolution. The analytical results for many case studies have been validated using an MHD numerical model. The main purpose of this investigation was deriving a practical analytical model for the electric arc, rendering possible its stabilization and control, and the enhancement of the plasma torch power.

  1. Novel plasma arc reactor with molted metal electrodes for coal gasification technology

    Energy Technology Data Exchange (ETDEWEB)

    Predtechensky, M.R.; Kuropyatnik, I.N.; Tukhto, O.M. [International Scientific Center on Thermophysics and Energetics, Novosibirsk, Russia Institute of Thermophysics SB RAS, Novosibirsk (Russian Federation)

    2001-07-01

    The process of steam gasification of coal has been studied using the new type of plasma chemical reactor with molten metal electrodes. Using of molten metal electrodes allows to increase significantly the continuous operation of the plasma arc reactor and to realize some additional advantages. (authors)

  2. Vacuum arc plasma thrusters with inductive energy storage driver

    Science.gov (United States)

    Krishnan, Mahadevan (Inventor)

    2009-01-01

    A plasma thruster with a cylindrical inner and cylindrical outer electrode generates plasma particles from the application of energy stored in an inductor to a surface suitable for the formation of a plasma and expansion of plasma particles. The plasma production results in the generation of charged particles suitable for generating a reaction force, and the charged particles are guided by a magnetic field produced by the same inductor used to store the energy used to form the plasma.

  3. High Current, High Density Arc Plasma as a New Source for WiPAL

    Science.gov (United States)

    Waleffe, Roger; Endrizzi, Doug; Myers, Rachel; Wallace, John; Clark, Mike; Forest, Cary; WiPAL Team

    2016-10-01

    The Wisconsin Plasma Astrophysics Lab (WiPAL) has installed a new array of nineteen plasma sources (plasma guns) on its 3 m diameter, spherical vacuum vessel. Each gun is a cylindrical, molybdenum, washer-stabilized, arc plasma source. During discharge, the guns are maintained at 1.2 kA across 100 V for 10 ms by the gun power supply establishing a high density plasma. Each plasma source is fired independently allowing for adjustable plasma parameters, with densities varying between 1018 -1019 m-3 and electron temperatures of 5-15 eV. Measurements were characterized using a 16 tip Langmuir probe. The plasma source will be used as a background plasma for the magnetized coaxial plasma gun (MCPG), the Terrestrial Reconnection Experiment (TREX), and as the plasma source for a magnetic mirror experiment. Temperature, density, and confinement results will be presented. This work is supported by the DoE and the NSF.

  4. Differential Inactivation of Fungal Spores in Water and on Seeds by Ozone and Arc Discharge Plasma.

    Directory of Open Access Journals (Sweden)

    Min Ho Kang

    Full Text Available Seed sterilization is essential for preventing seed borne fungal diseases. Sterilization tools based on physical technologies have recently received much attention. However, available information is very limited in terms of efficiency, safety, and mode of action. In this study, we have examined antifungal activity of ozone and arc discharge plasma, potential tools for seed sterilization. In our results, ozone and arc discharge plasma have shown differential antifungal effects, depending on the environment associated with fungal spores (freely submerged in water or infected seeds. Ozone inactivates Fusarium fujikuroi (fungus causing rice bakanae disease spores submerged in water more efficiently than arc discharge plasma. However, fungal spores associated with or infecting rice seeds are more effectively deactivated by arc discharge plasma. ROS generated in water by ozone may function as a powerful fungicidal factor. On the other hand, shockwave generated from arc discharge plasma may have greatly contributed to antifungal effects on fungus associated with rice seeds. In support of this notion, addition of ultrasonic wave in ozone generating water has greatly increased the efficiency of seed disinfection.

  5. Differential Inactivation of Fungal Spores in Water and on Seeds by Ozone and Arc Discharge Plasma

    Science.gov (United States)

    Kang, Min Ho; Pengkit, Anchalee; Choi, Kihong; Jeon, Seong Sil; Choi, Hyo Won; Shin, Dong Bum; Choi, Eun Ha; Uhm, Han Sup; Park, Gyungsoon

    2015-01-01

    Seed sterilization is essential for preventing seed borne fungal diseases. Sterilization tools based on physical technologies have recently received much attention. However, available information is very limited in terms of efficiency, safety, and mode of action. In this study, we have examined antifungal activity of ozone and arc discharge plasma, potential tools for seed sterilization. In our results, ozone and arc discharge plasma have shown differential antifungal effects, depending on the environment associated with fungal spores (freely submerged in water or infected seeds). Ozone inactivates Fusarium fujikuroi (fungus causing rice bakanae disease) spores submerged in water more efficiently than arc discharge plasma. However, fungal spores associated with or infecting rice seeds are more effectively deactivated by arc discharge plasma. ROS generated in water by ozone may function as a powerful fungicidal factor. On the other hand, shockwave generated from arc discharge plasma may have greatly contributed to antifungal effects on fungus associated with rice seeds. In support of this notion, addition of ultrasonic wave in ozone generating water has greatly increased the efficiency of seed disinfection. PMID:26406468

  6. Synthesis method for ultrananocrystalline diamond in powder employing a coaxial arc plasma gun

    Science.gov (United States)

    Naragino, Hiroshi; Tominaga, Aki; Hanada, Kenji; Yoshitake, Tsuyoshi

    2015-07-01

    A new method that enables us to synthesize ultrananocrystalline diamond (UNCD) in powder is proposed. Highly energetic carbon species ejected from a graphite cathode of a coaxial arc plasma gun were provided on a quartz plate at a high density by repeated arc discharge in a compact vacuum chamber, and resultant films automatically peeled from the plate were aggregated and powdered. The grain size was easily controlled from 2.4 to 15.0 nm by changing the arc discharge energy. It was experimentally demonstrated that the proposed method is a new and promising method that enables us to synthesize UNCD in powder easily and controllably.

  7. Simulation of droplet transfer process and current waveform control of CO2 arc welding

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A simulation system used in the arc welding short-circuit transfer process and current waveform control process was developed in this paper. The simulation results are basically consistent with welding technical experiments. The simulation system can be used to simulate and test the current waveform control parameters with welding variables. By this simulation system, the influence regularities of the current waveform control parameters in the CO2 arc welding droplet short-circuit transfer process can be got. Moreover, the basic mode of real-time current waveform control can be also established by the simulation testing.

  8. Characterization of duplex stainless steel weld metals obtained by hybrid plasma-gas metal arc welding

    Directory of Open Access Journals (Sweden)

    Koray Yurtisik

    2013-09-01

    Full Text Available Despite its high efficiency, autogenous keyhole welding is not well-accepted for duplex stainless steels because it causes excessive ferrite in as-welded duplex microstructure, which leads to a degradation in toughness and corrosion properties of the material. Combining the deep penetration characteristics of plasma arc welding in keyhole mode and metal deposition capability of gas metal arc welding, hybrid plasma - gas metal arc welding process has considered for providing a proper duplex microstructure without compromising the welding efficiency. 11.1 mm-thick standard duplex stainless steel plates were joined in a single-pass using this novel technique. Same plates were also subjected to conventional gas metal arc and plasma arc welding processes, providing benchmarks for the investigation of the weldability of the material. In the first place, the hybrid welding process enabled us to achieve less heat input compared to gas metal arc welding. Consequently, the precipitation of secondary phases, which are known to be detrimental to the toughness and corrosion resistance of duplex stainless steels, was significantly suppressed in both fusion and heat affected zones. Secondly, contrary to other keyhole techniques, proper cooling time and weld metal chemistry were achieved during the process, facilitating sufficient reconstructive transformation of austenite in the ferrite phase.

  9. Synthesis of Single Wall Carbon Nanotubes by Plasma Arc: Role of Plasma Parameters

    Science.gov (United States)

    Farhart, Samir; Scott, Carl D.

    2000-01-01

    Single wall carbon nanotubes (SWNT) are porous objects on the molecular scale and have a low density, which gives them potential applications as adsorbent for molecular hydrogen. Their H2 absorption capacity published in the literature varies from 4 to 10% by mass according to the purity of the materials and storage conditions. Optimization of production methods of SWNTs should permit improving these new materials for storage of hydrogen. In this article, we show the potential of using SWNTs in hydrogen storage. In particular, we pose problems associated with synthesis, purification, and opening up of the nanotubes. We present an electric arc process currently used at laboratory scale to produce single wall carbon nanotubes. We discuss, in particular, operating conditions that permit growth of nanotubes and some plasma parameters that assure control of the material. Analysis of the process is carried out with the aid of local measurements of temperature and scanning and transmission electron microscopy of the materials.

  10. Relationship between sound signal and weld pool status in plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The sound features of the weld pool status in plasma arc welding were systematically investigated after the sound signal was collected with a microphone. The results show that it is difficult to extract information about the weld pool status directly in time domain although the sound signal varies with the weld pool behaviors to some extent. The frequency spectra of the sound signal contain plenty of information about the weld pool behaviors. It is shown from the analysis of the sound generation mechanism that the sound signal of plasma arc welding is mainly caused by the weld pool oscillation, the power source fluctuation and so on. RS algorithm is designed to determine the weld pool status, and it is able to offer the feedback information for the closed-loop control of the penetration quality of plasma arc welding.

  11. Variation of plasma parameters of vacuum arc column with gap distance

    Science.gov (United States)

    Han, Wen; Yuan, Zhao; He, Junjia

    2016-07-01

    On the basis of a two-dimensional (2D) magneto-hydrodynamic model, we studied long-gap-distance vacuum arcs in a uniform axial magnetic field and determined the effect of gap distance varying in a large range on plasma parameters. Simulation results showed that with increasing gap distance, the parameters of the plasma near the cathode are almost invariant, except for ion number density, but the parameters of the plasma in front of the anode clearly vary; meanwhile, joule heat gradually becomes the main source of energy for the arc column. In a short gap, a clear current constriction can be found in the entire arc column. Whereas when the gap distance exceeds a certain value, a sharp contraction of the current only arises in front of the anode.

  12. High current multicharged metal ion source using high power gyrotron heating of vacuum arc plasma.

    Science.gov (United States)

    Vodopyanov, A V; Golubev, S V; Khizhnyak, V I; Mansfeld, D A; Nikolaev, A G; Oks, E M; Savkin, K P; Vizir, A V; Yushkov, G Yu

    2008-02-01

    A high current, multi charged, metal ion source using electron heating of vacuum arc plasma by high power gyrotron radiation has been developed. The plasma is confined in a simple mirror trap with peak magnetic field in the plug up to 2.5 T, mirror ratio of 3-5, and length variable from 15 to 20 cm. Plasma formed by a cathodic vacuum arc is injected into the trap either (i) axially using a compact vacuum arc plasma gun located on axis outside the mirror trap region or (ii) radially using four plasma guns surrounding the trap at midplane. Microwave heating of the mirror-confined, vacuum arc plasma is accomplished by gyrotron microwave radiation of frequency 75 GHz, power up to 200 kW, and pulse duration up to 150 micros, leading to additional stripping of metal ions by electron impact. Pulsed beams of platinum ions with charge state up to 10+, a mean charge state over 6+, and total (all charge states) beam current of a few hundred milliamperes have been formed.

  13. Numerical analysis of transient keyhole shape in pulsed current plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    孙俊华; 武传松

    2014-01-01

    Based on the characteristics of“one keyhole in a pulse”in pulsed current plasma arc welding (PAW),the transient variation process ofweld pool in a pulse cycle is simulated through the establishment ofcorresponding heat source model.And considering the effects ofgravitational force,plasma arc pressure and surface tension on the weld pool surface,the dynamic change features of the keyhole shape in a pulse cycle are calculated by using surface deformation equation. Experiments are conducted and validate that the calculated weld fusion line is in good agreement with the experimental results.

  14. A computer-based control system for keyhole plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    Jia Chuanbao; Wu Chuansong; Zhang Yuming

    2007-01-01

    A new kind of control system for keyhole plasma arc welding (K-PAW) was developed based on the computer and the Graphics Language-LabVIEW. It can set and output the required current waveforms with desired decreasing slopes so that the corresponding "opening and closing" of keyhole can occur periodically. With this control strategy of welding current waveforms, the workpiece is fully penetrated while no burn-through occurs. Keyhole plasma arc welding experiments were conducted to verify the stability and reliability of the developed system.

  15. Application of orthogonal design in the experiment of plasma arc powder surfacing technology

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In this paper, the influence of plasma arc powder surfacing technical parameters on the property of layer is defined using the orthogonal design. By the orthogonal polynomial regression, when plasma arc powder surfacing is used on the surface of the X65 steel plate with the Fe-07 alloy powder, the optimum technical parameters are the following: I=180190 A, G=41.5 g/min, v=102 mm/min, T0=350℃, Ql=280 L/h, Qs=400 L/h. Further, analysis of the cracking test data showed that the cracking preheat temperature is 350℃.

  16. Coupled gas flow-plasma model for a gliding arc: investigations of the back-breakdown phenomenon and its effect on the gliding arc characteristics

    Science.gov (United States)

    Sun, S. R.; Kolev, St.; Wang, H. X.; Bogaerts, A.

    2017-01-01

    We present a 3D and 2D Cartesian quasi-neutral plasma model for a low current argon gliding arc discharge, including strong interactions between the gas flow and arc plasma column. The 3D model is applied only for a short time of 0.2 ms due to its huge computational cost. It mainly serves to verify the reliability of the 2D model. As the results in 2D compare well with those in 3D, they can be used for a better understanding of the gliding arc basic characteristics. More specifically, we investigate the back-breakdown phenomenon induced by an artificially controlled plasma channel, and we discuss its effect on the gliding arc characteristics. The back-breakdown phenomenon, or backward-jump motion of the arc, as observed in the experiments, results in a drop of the gas temperature, as well as in a delay of the arc velocity with respect to the gas flow velocity, allowing more gas to pass through the arc, and thus increasing the efficiency of the gliding arc for gas treatment applications.

  17. ARC Code TI: Self-Healing Independent File Transfer (Shift)

    Data.gov (United States)

    National Aeronautics and Space Administration — Shift is a lightweight framework for high performance local and remote file transfers that provides resiliency across a wide variety of failure scenarios through...

  18. Magnetic Dipole Inflation with Cascaded ARC and Applications to Mini-Magnetospheric Plasma Propulsion

    Science.gov (United States)

    Giersch, L.; Winglee, R.; Slough, J.; Ziemba, T.; Euripides, P.

    2003-01-01

    Mini-Magnetospheric Plasma Propulsion (M2P2) seeks to create a plasma-inflated magnetic bubble capable of intercepting significant thrust from the solar wind for the purposes of high speed, high efficiency spacecraft propulsion. Previous laboratory experiments into the M2P2 concept have primarily used helicon plasma sources to inflate the dipole magnetic field. The work presented here uses an alternative plasma source, the cascaded arc, in a geometry similar to that used in previous helicon experiments. Time resolved measurements of the equatorial plasma density have been conducted and the results are discussed. The equatorial plasma density transitions from an initially asymmetric configuration early in the shot to a quasisymmetric configuration during plasma production, and then returns to an asymmetric configuration when the source is shut off. The exact reasons for these changes in configuration are unknown, but convection of the loaded flux tube is suspected. The diffusion time was found to be an order of magnitude longer than the Bohm diffusion time for the period of time after the plasma source was shut off. The data collected indicate the plasma has an electron temperature of approximately 11 eV, an order of magnitude hotter than plasmas generated by cascaded arcs operating under different conditions. In addition, indirect evidence suggests that the plasma has a beta of order unity in the source region.

  19. Dimensionless factors for an alternating-current non-thermal arc plasma

    Science.gov (United States)

    Zhang, Si-Yuan; Li, Xiao-Song; Liu, Jin-Bao; Liu, Jing-Lin; Li, He-Ping; Zhu, Ai-Min

    2016-12-01

    A gliding arc discharge, as a source of warm plasma combining advantages of both thermal and cold plasmas, would have promising application prospects in the fields of fuel conversion, combustion enhancement, material synthesis, surface modifications, pollution control, etc. In order to gain insight into the features of an alternating-current gliding arc discharge plasma, three dimensionless factors, i.e., the extinction span (ψ), current lag (δ), and heating lag (χ) factors are proposed in this letter based on the measured waveforms of the discharge voltage and current in an AC gliding arc discharge plasma. The influences of the driving frequency of the power supply (f) on these three dimensionless parameters are investigated experimentally with the explanations on the physical meanings of these factors. The experimental results show that a higher value of f would lead to the lower values of ψ and δ, as well as a higher value of χ. These experimental phenomena indicate a lower threshold ignition voltage of the discharges, a lower current-growth inertia of the gliding arcs and a larger relative thermal inertia of the plasmas with increase the driving frequency of the power supply in the operating parameter range studied in this letter.

  20. Plasma-chemical reactor based on a low-pressure pulsed arc discharge for synthesis of nanopowders

    Science.gov (United States)

    Karpov, I. V.; Ushakov, A. V.; Lepeshev, A. A.; Fedorov, L. Yu.

    2017-01-01

    A reactor for producing nanopowders in the plasma of a low-pressure arc discharge has been developed. As a plasma source, a pulsed cold-cathode arc evaporator has been applied. The design and operating principle of the reactor have been described. Experimental data on how the movement of a gaseous mixture in the reactor influences the properties of nanopowders have been presented.

  1. Ionospheric Plasma Circulation Associated with Polar Cap Arcs Detached from the Auroral Oval

    Science.gov (United States)

    Yakymenko, K.; Koustov, A. V.; Hosokawa, K.; Shiokawa, K.

    2015-12-01

    Joint observations of the OMTI all-sky camera at Resolute Bay, NWT (Canada), the SuperDARN radars and Swarm satellites are considered to investigate horizontal plasma flows and vertical field-aligned currents (FACs) associated with polar cap arcs "detached" from the auroral oval but not penetrated deep into the polar cap. All cases are for the near winter solstice, positive IMF Bz and mostly dominating IMF By. We show that the arcs are usually co-exist with strong flow shears driven by electric fields of the converging type. The shears, being added to the background flow, produce unusual convection patterns, for example reverse (sunward) flows on the nightside, several MLT hours away from the noon-midnight line. We also investigate the distribution of FACs in the arcs' vicinity, both duskward and dawnward, for several Swarm passes. Electron density data onboard Swarm satellites are used to identify the arc and auroral oval boundaries, along with the ground-based optics. The data suggest that the arcs correspond to a separate current system excited in addition to the background plasma circulation governed by the reconnection processes.Joint observations of the OMTI all-sky camera at Resolute Bay, NWT (Canada), the SuperDARN radars and Swarm satellites are considered to investigate horizontal plasma flows and vertical field-aligned currents (FACs) associated with polar cap arcs "detached" from the auroral oval but not penetrated deep into the polar cap. All cases are for the near winter solstice, positive IMF Bz and mostly dominating IMF By. We show that the arcs are usually co-exist with strong flow shears driven by electric fields of the converging type. The shears, being added to the background flow, produce unusual convection patterns, for example reverse (sunward) flows on the nightside, several MLT hours away from the noon-midnight line. We also investigate the distribution of FACs in the arcs' vicinity, both duskward and dawnward, for several Swarm passes

  2. Dynamics of cathode spots in low-pressure arc plasma removing oxide layer on steel surfaces

    Science.gov (United States)

    Tang, Z. L.; Yang, K.; Liu, H. X.; Zhang, Y. C.; Li, H.; Zhu, X. D.

    2016-03-01

    The dynamics of cathode spots has been investigated in low-pressure arc plasma for removing oxide layer on low carbon steel surfaces. The motion of cathode spots was observed with a high speed camera, and the arc voltage was analyzed by fast Fourier transform. The spots move on clean steel surface as a random walk, and the low-frequency components dominated the voltage waveform. However, the spots on steel surfaces with oxide layer tend to burn on the rim of the eroded area formed in the previous arcing, and the low-frequency components decrease correspondingly. The "color" of the colored random noise for arc voltage varies from the approximate brown noise for clean steel surface to pink noise for thick oxide layer, where the edge effect of boundary is considered to play a significant role.

  3. Correlation methods in cutting arcs

    Energy Technology Data Exchange (ETDEWEB)

    Prevosto, L; Kelly, H, E-mail: prevosto@waycom.com.ar [Grupo de Descargas Electricas, Departamento Ing. Electromecanica, Universidad Tecnologica Nacional, Regional Venado Tuerto, Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina)

    2011-05-01

    The present work applies similarity theory to the plasma emanating from transferred arc, gas-vortex stabilized plasma cutting torches, to analyze the existing correlation between the arc temperature and the physical parameters of such torches. It has been found that the enthalpy number significantly influence the temperature of the electric arc. The obtained correlation shows an average deviation of 3% from the temperature data points. Such correlation can be used, for instance, to predict changes in the peak value of the arc temperature at the nozzle exit of a geometrically similar cutting torch due to changes in its operation parameters.

  4. Sensing controlled pulse key-holing condition in plasma arc welding

    Institute of Scientific and Technical Information of China (English)

    JIA Chuan-bao; WU Chuan-song; ZHANG Yu-ming

    2009-01-01

    According to the strategy of controlled pulse key-holing, a new sensing and control system was developed for monitoring and controlling the keyhole condition during plasma arc welding (PAW). Through sensing and processing the efflux plasma voltage signals, the quantitative relationship among the welding current, efflux plasma voltage and backside weld width of the weld was established. PAW experiments show that the efflux plasma voltage can reflect the state of keyhole and backside weld width accurately. The closed-loop control tests validate the stability and reliability of the developed keyhole PAW system.

  5. Volt-ampere characteristics of a nitrogen DC plasma arc with anode melting

    Institute of Scientific and Technical Information of China (English)

    Zhao Peng; Ni Guo-Hua; Meng Yue-Dong; Nagatsu Masaaki

    2013-01-01

    The characteristics of a nitrogen arc using a graphite cathode and a melting anode in a pilot-scale plasma furnace are investigated.The voltage is examined as a function of current and apparent plasma length.The voltage increases non-linearly with the increase of apparent plasma length,with the current fixed.The experimental data so obtained are compared with the predictions of the Bowman model for the electric arc,and with numerical simulations as well.The level of agreement between the experimental data at the melting anode and the numerical predictions confirms the suitability of the proposed the Bowman model.These characteristics are relevant to the engineering design and evaluation of a DC plasma furnace and reactor for the treatment of hazardous fly ash waste.

  6. Effect of Feed Forms on the Results of Melting of Fly Ash by a DC Plasma Arc Furnace

    Institute of Scientific and Technical Information of China (English)

    CHEN Mingzhou; MENG Yuedong; SHI Jiabiao; NI Guohua; JIANG Yiman; YU Xinyao; ZHAO Peng

    2009-01-01

    Fly ash from a municipal solid waste incinerator (MSWI) without preprocessing (original fly ash,OFA) was melted by a direct current (DC) plasma arc furnace to investigate how the feed forms governed the results.Dioxins in flue gas from stack and bag-filter ash (BFA) were detected.The distribution of heavy metals of Pb,Cd,As,and Cr along the flue gas process system was analyzed.Through a comparison of the results for dioxins and heavy metals in this study and previous work,carrying-over of fly ash particles with the flue gas stream can be deduced.Based on the magnetic induction equation and Navier-Stokes equations,a magnetohydrodynamic (MHD) model for the plasma arc was developed to describe the particle-carrying effect.The results indicate that,a.when melted,the feed forms of MSWI fly ash affect the results significantly;b.it is not preferable to melt MSWI fly ash directly,and efforts should be made to limit the mass transfer of OFA from the plasma furnace.

  7. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    NARCIS (Netherlands)

    Zhu, J.; Gao, J.; Ehn, A.; Alden, M.; Li, Z.; Moseev, D.; Kusano, Y.; Salewski, M.; Alpers, A.; Gritzmann, P.; Schwenk, M.

    2015-01-01

    A non-thermal gliding arc discharge was generated at atmospheric pressure in an air flow. The dynamics of the plasma column and tracer particles were recorded using two synchronized highspeed cameras. Whereas the data analysis for such systems has previously been performed in 2D (analyzing the singl

  8. Finite element analysis of keyhole plasma arc welding based on an adaptive heat source mode

    Institute of Scientific and Technical Information of China (English)

    Hu Qingxian; Wu Chuansong; Zhang Yuming

    2007-01-01

    An adaptive heat source mode is proposed to account for the keyhole effect and the characteristics of volumetric distribution along the direction of the workpiece thickness. Finite element analysis of the temperature field in keyhole plasma arc welding is conducted and the weld geometry is obtained. The predicted results are in agreement with the measured ones.

  9. Micro-scale Plasma Arc Gasification for Waste Treatment and Energy Production Project

    Science.gov (United States)

    Caraccio, Anne

    2015-01-01

    As NASA continues to develop technology for spaceflight beyond low earth orbit, we must develop the right systems for sustaining human life on a long duration or planetary mission. Plasma arc gasification (PAG) is an energy efficient mechanism of waste management for power generation and synthetic gas(syngas) production.

  10. Preparation and characterization of carbon nanofluid by a plasma arc nanoparticles synthesis system

    Directory of Open Access Journals (Sweden)

    Pai Feng-Yi

    2011-01-01

    Full Text Available Abstract Heat dissipation from electrical appliances is a significant issue with contemporary electrical devices. One factor in the improvement of heat dissipation is the heat transfer performance of the working fluid. In this study, we used plasma arc technology to produce a nanofluid of carbon nanoparticles dispersed in distilled water. In a one-step synthesis, carbon was simultaneously heated and vaporized in the chamber, the carbon vapor and particles were then carried to a collector, where cooling furnished the desired carbon/water nanofluid. The particle size and shape were determined using the light-scattering size analyzer, SEM, and TEM. Crystal morphology was examined by XRD. Finally, the characterization include thermal conductivity, viscosity, density and electric conductivity were evaluated by suitable instruments under different temperatures. The thermal conductivity of carbon/water nanofluid increased by about 25% at 50°C compared to distilled water. The experimental results demonstrated excellent thermal conductivity and feasibility for manufacturing of carbon/water nanofluids.

  11. Surface Plasma Arc by Radio-Frequency Control Study (SPARCS)

    Energy Technology Data Exchange (ETDEWEB)

    Ruzic, David N. [University of Illinois at Urbana-Champaign, IL (United States)

    2013-04-29

    This paper is to summarize the work carried out between April 2012 and April 2013 for development of an experimental device to simulate interactions of o -normal detrimental events in a tokamak and ICRF antenna. The work was mainly focused on development of a pulsed plasma source using theta pinch and coaxial plasma gun. This device, once completed, will have a possible application as a test stand for high voltage breakdown of an ICRF antenna in extreme events in a tokamak such as edge-localized modes or disruption. Currently, DEVeX does not produce plasma with high temperature enough to requirement for an ELM simulator. However, theta pinch is a good way to produce high temperature ions. The unique characteristic of plasma heating by a theta pinch is advantageous for an ELM simulator due to its effective ion heating. The objective of the proposed work, therefore, is to build a test facility using the existing theta pinch facility in addition to a coaxial plasma gun. It is expected to produce a similar pulsed-plasma heat load to the extreme events in tokamaks and to be applied for studying interactions of hot plasma and ICRF antennas.

  12. Vacuum arc with a distributed cathode spot as a plasma source for plasma separation of spent nuclear fuel and radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Amirov, R. Kh., E-mail: ravus46@yandex.ru; Vorona, N. A.; Gavrikov, A. V.; Lizyakin, G. D.; Polishchuk, V. P.; Samoilov, I. S.; Smirnov, V. P.; Usmanov, R. A.; Yartsev, I. M. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation)

    2015-10-15

    Results from experimental studies of a vacuum arc with a distributed cathode spot on the heated cathode are presented. Such an arc can be used as a plasma source for plasma separation of spent nuclear fuel and radioactive waste. The experiments were performed with a gadolinium cathode, the properties of which are similar to those of an uranium arc cathode. The heat flux from the plasma to the cathode (and its volt equivalent) at discharge voltages of 4-15 V and discharge currents of 44-81 A, the radial distribution of the emission intensity of gadolinium atoms and singly charged ions in the arc channel at a voltage of 4.3 V, and the plasma electron temperature behind the anode were measured. The average charge of plasma ions at arc voltages of 3.5-8 V and a discharge current of 52 A and the average rate of gadolinium evaporation in the discharge were also determined.

  13. Titanium nitride plasma-chemical synthesis with titanium tetrachloride raw material in the DC plasma-arc reactor

    Science.gov (United States)

    Kirpichev, D. E.; Sinaiskiy, M. A.; Samokhin, A. V.; Alexeev, N. V.

    2017-04-01

    The possibility of plasmochemical synthesis of titanium nitride is demonstrated in the paper. Results of the thermodynamic analysis of TiCl4 - H2 - N2 system are presented; key parameters of TiN synthesis process are calculated. The influence of parameters of plasma-chemical titanium nitride synthesis process in the reactor with an arc plasmatron on characteristics on the produced powders is experimentally investigated. Structure, chemical composition and morphology dependencies on plasma jet enthalpy, stoichiometric excess of hydrogen and nitrogen in a plasma jet are determined.

  14. Mechanism of surface modification in the plasma-surface interaction in electrical arcs

    CERN Document Server

    Timko, H; Nordlund, K; Costelle, L; Matyash, K; Schneider, R; Toerklep, A; Arnau-Izquierdo, G; Descoeudres, A; Calatroni, S; Taborelli, M; Wuensch, W

    2010-01-01

    Electrical sparks and arcs are plasma discharges that carry large currents and can strongly modify surfaces. This damage usually comes in the form of micrometer-sized craters and frozen-in liquid on the surface. Using a combination of experiments, plasma and atomistic simulation tools, we now show that the observed formation of deep craters and liquidlike features during sparking in vacuum is explained by the impacts of energetic ions, accelerated under the given conditions in the plasma sheath to kiloelectron volt energies, on surfaces. The flux in arcs is so high that in combination with kiloelectron volt energies it produces multiple overlapping heat spikes, which can lead to cratering even in materials such as Cu, where a single heat spike normally does not.

  15. Mechanism of surface modification in the plasma surface interaction in electrical arcs

    CERN Document Server

    Timko, Helga; Djurabekova, Flyura; Nordlund, Kai; Matyash, Konstantin; Schneider, Ralf; Toerklep, Anders; Arnau-Izquierdo, Gonzalo; Descoeudres, Antoine; Calatroni, Sergio; Taborelli, Mauro; Wuensch, Walter

    2010-01-01

    Electrical sparks and arcs are plasma discharges that carry large currents and can strongly modify surfaces. This damage usually comes in the form of micrometer-sized craters and frozen-in liquid on the surface. Using a combination of experiments, plasma and atomistic simulation tools, we now show that the observed formation of deep craters and liquidlike features during sparking in vacuum is explained by the impacts of energetic ions, accelerated under the given conditions in the plasma sheath to kiloelectron volt energies, on surfaces. The flux in arcs is so high that in combination with kiloelectron volt energies it produces multiple overlapping heat spikes, which can lead to cratering even in materials such as Cu, where a single heat spike normally does not.

  16. Spectroscopic studies of plasma in a carbon arc discharge for synthesis of nanomaterials

    Science.gov (United States)

    Vekselman, Vladislav; Feurer, Matthew; Yeh, Yao-Wen; Stratton, Brentley; Raitses, Yevgeny; LaboratoryPlasma Nanosynthesis Team

    2016-09-01

    An atmospheric pressure arc discharge with graphite electrodes is commonly used for synthesis of carbon nanomaterials such as buckyballs, nanotubes and graphene. In operation, the graphite anode ablates providing a feedstock material for synthesis these carbon nanostructures. Existing models predict that nucleation and growth of these nanomaterials in an arc discharge are governed by spatial distributions of density and temperature of plasma species. Control of these distributions can potentially enable optimization of nanosynthesis processes, to achieve the best combination of synthesis selectivity at the synthesis yield. In this work, we report first detail measurements of spatial distribution of arc plasma parameters obtained with a set of in-situ diagnostics, including optical emission spectroscopy and fast framing imaging. These parameters were measured in low- and high- anode ablation modes. Results of these measurements demonstrate a strong correlation between arc plasma and synthesis processes. This work was supported by U.S. Department of Energy, Office of Science, Basic Sciences, Materials Sciences and Engineering Division.

  17. Nitrogen Fixation by Gliding Arc Plasma: Better Insight by Chemical Kinetics Modelling.

    Science.gov (United States)

    Wang, Weizong; Patil, Bhaskar; Heijkers, Stjin; Hessel, Volker; Bogaerts, Annemie

    2017-05-22

    The conversion of atmospheric nitrogen into valuable compounds, that is, so-called nitrogen fixation, is gaining increased interest, owing to the essential role in the nitrogen cycle of the biosphere. Plasma technology, and more specifically gliding arc plasma, has great potential in this area, but little is known about the underlying mechanisms. Therefore, we developed a detailed chemical kinetics model for a pulsed-power gliding-arc reactor operating at atmospheric pressure for nitrogen oxide synthesis. Experiments are performed to validate the model and reasonable agreement is reached between the calculated and measured NO and NO2 yields and the corresponding energy efficiency for NOx formation for different N2 /O2 ratios, indicating that the model can provide a realistic picture of the plasma chemistry. Therefore, we can use the model to investigate the reaction pathways for the formation and loss of NOx . The results indicate that vibrational excitation of N2 in the gliding arc contributes significantly to activating the N2 molecules, and leads to an energy efficient way of NOx production, compared to the thermal process. Based on the underlying chemistry, the model allows us to propose solutions on how to further improve the NOx formation by gliding arc technology. Although the energy efficiency of the gliding-arc-based nitrogen fixation process at the present stage is not comparable to the world-scale Haber-Bosch process, we believe our study helps us to come up with more realistic scenarios of entering a cutting-edge innovation in new business cases for the decentralised production of fertilisers for agriculture, in which low-temperature plasma technology might play an important role. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Trans-lithospheric scheme of arc magma transfer and evolution (Invited)

    Science.gov (United States)

    Bouilhol, P.; Schmidt, M. W.; Connolly, J. A.; Burg, J.

    2013-12-01

    Understanding the formation of magmatic arcs requires not only conceiving the formation of primitive arc melts, but also their evolution during migration from the mantle source to the arc. Indeed, the chemical characteristics of arc-melts are acquired during a complex process involving the slab input, the mantle wedge, and transfer of the melt at the base of and in the crust. Because the retrograde thermal regime in the upper portion of the mantle wedge is hostile to melt transport, the dominant mechanism by which melts ascend from their source through the mantle remains uncertain and mainly based on theoretical and exported models from MOR settings because of the scarcity of observations available. Within the lower crust, melts must be efficiently transferred toward higher structural levels to feed plutons and volcanoes but such melt highways are elusive and not always recognized as such. Petro-geochemical and structural analyses conducted on a mantle and lower crust section of the Kohistan Paleo-Island Arc (The Sapat Complex, Pakistan) unravel some aspects of the transfer and evolution of arc-magmas. The dominantly harzburgitic mantle shows a continuum of transport mechanisms ranging from pervasive to fully segregated melt flow, related to the formation of dunitic conduits associated with clinopyroxene-rich zones. Structural observations, linked to rock chemistry and numerical simulations show that primitive melts where transferred via porosity waves within the mantle. This efficient way of forming mantle conduit will drain the primitive mantle source region until melting cease. During this transfer, a competitive series of reaction-crystallization marks the staggering of melt evolution. The crustal section, fed with the same primitive melt, is predominantly composed of meta-plutonics that host kilometer-scale pyroxenite bodies. Within the bodies, sub-vertical magmatic and reactional structures indicate vertical magma percolation accompanied by massive cumulate

  19. On Vitrifying Wastes Using a Plasma Arc Torch

    Science.gov (United States)

    2002-08-01

    environmental research and waste management policy. She labored in a milieu of resource shortage , severe time constraints and borrowed facilities...municipal solid waste) a syngas may also be collected during vitrification and either sold or used on site to power the torch itself. Finally, plasma

  20. Disposal of spent tributylphosphate by gliding arc plasma.

    Science.gov (United States)

    Moussa, David; Brisset, Jean Louis

    2003-08-29

    The gliding arc in humid air is a relevant source of free radicals and strongly oxidising species such as HO* (shown by emission spectroscopy), which are able to degrade organic wastes. This feature was used in a new process for mineralising spent tributylphosphate (TBP) which is an important waste from nuclear industry. The degradation kinetics is examined by monitoring the conversion of TBP into phosphoric acid in a batch reactor. The kinetics exhibits three steps and especially an overall zero-order linear step with a rate of 10 mmol h(-1) at the beginning of the treatment. This zero-order step agrees with a surface oxidation process. After a 13.7h treatment, about 45% of the TBP is converted into inorganic phosphorus compounds, with phosphoric acid as the major product (63% of inorganic phosphorus compounds), and at least 19.5% is not degraded. Dibutylphosphoric acid (HDBP) was identified as the main by-product by a nuclear magnetic resonance technique, infrared spectroscopy and gas chromatography.

  1. Temperature and Nitric Oxide Generation in a Pulsed Arc Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    T.NAMIHIRA; S.SAKAI; M.MATSUDA; D.WANG; T.KIYAN; H.AKIYAMA; K.OKAMOTO; K.TODA

    2007-01-01

    Nitric oxide (NO) is increasingly being used in medical treatments of high blood pressure,acute respiratory distress syndrome and other illnesses related to the lungs.Currently a NO inhalation system consists of a gas cylinder of N2 mixed with a high concentration of NO.This arrangement is potentially risky due to the possibility of an accidental leak of NO from the cylinder.The presence of NO in the air leads to the formation of nitric dioxide (NO2),which is toxic to the lungs.Therefore,an on-site generator of NO would be highly desirable for medical doctors to use with patients with lung disease.To develop the NO inhalation system without a gas cylinder,which would include a high concentration of NO,NAMIHIRA et al have recently reported on the production of NO from room air using a pulsed arc discharge.In the present work,the temperature of the pulsed arc discharge plasma used to generate NO was measured to optimize the discharge condition.The results of the temperature measurements showed the temperature of the pulsed arc discharge plasma reached about 10,000 K immediately after discharge initiation and gradually decreased over tens of microseconds.In addition,it was found that NO was formed in a discharge plasma having temperatures higher than 9,000 K and a smaller input energy into the discharge plasma generates NO more efficiently than a larger one.

  2. Free fall plasma-arc reactor for synthesis of carbon nanotubes in microgravity

    Science.gov (United States)

    Alford, J. M.; Mason, G. R.; Feikema, D. A.

    2006-07-01

    High temperatures inside the plasma of a carbon arc generate strong buoyancy driven convection which has an effect on the growth and morphology of the single-walled carbon nanotubes (SWNTs). To study the effect of buoyancy on the arc process, a miniature carbon arc apparatus was designed and developed to synthesize SWNTs in a microgravity environment substantially free from buoyant convective flows. An arc reactor was operated in the 2.2 and 5.18s drop towers at the NASA Glenn Research Center. The apparatus employed a 4mm diameter anode and was powered by a portable battery pack capable of providing in excess of 300A at 30V to the arc for the duration of a 5s drop. However, the principal result is that no dramatic difference in sample yield or composition was noted between normal gravity and 2.2 and 5s long microgravity runs. Much longer duration microgravity time is required for SWNT's growth such as the zero-G aircraft, but more likely will need to be performed on the international space station or an orbiting spacecraft.

  3. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Jiajian; Gao, Jinlong; Ehn, Andreas; Aldén, Marcus; Li, Zhongshan, E-mail: zhongshan.li@forbrf.lth.se, E-mail: alpers@ma.tum.de [Division of Combustion Physics, Lund University, P.O. Box 118, S-221 00 Lund (Sweden); Moseev, Dmitry [Max-Planck-Institut für Plasmaphysik, D-85748 Garching bei München (Germany); FOM Institute DIFFER, 3430 BE Nieuwegein (Netherlands); Kusano, Yukihiro [Department of Wind Energy, Section for Composites and Materials Mechanics, Technical University of Denmark, Risø Campus, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Salewski, Mirko [Department of Physics, Section for Plasma Physics and Fusion Energy, Technical University of Denmark, DK-2800 Kongens Lyngby (Denmark); Alpers, Andreas, E-mail: zhongshan.li@forbrf.lth.se, E-mail: alpers@ma.tum.de; Gritzmann, Peter; Schwenk, Martin [Zentrum Mathematik, Technische Universität München, D-85747 Garching bei München (Germany)

    2015-01-26

    A non-thermal gliding arc discharge was generated at atmospheric pressure in an air flow. The dynamics of the plasma column and tracer particles were recorded using two synchronized high-speed cameras. Whereas the data analysis for such systems has previously been performed in 2D (analyzing the single camera image), we provide here a 3D data analysis that includes 3D reconstructions of the plasma column and 3D particle tracking velocimetry based on discrete tomography methods. The 3D analysis, in particular, the determination of the 3D slip velocity between the plasma column and the gas flow, gives more realistic insight into the convection cooling process. Additionally, with the determination of the 3D slip velocity and the 3D length of the plasma column, we give more accurate estimates for the drag force, the electric field strength, the power per unit length, and the radius of the conducting zone of the plasma column.

  4. Sheared magnetospheric plasma flows and discrete auroral arcs: a quasi-static coupling model

    Directory of Open Access Journals (Sweden)

    M. M. Echim

    2007-02-01

    Full Text Available We consider sheared flows in magnetospheric boundary layers of tangential discontinuity type, forming a structure that is embedded in a large-scale convergent perpendicular electric field. We construct a kinetic model that couples the magnetospheric structure with the topside ionosphere. The contribution of magnetospheric electrons and ionospheric electrons and ions is taken into account into the current-voltage relationship derived for an electric potential monotonically decreasing with the altitude. The solution of the current continuity equation gives the distribution of the ionospheric potential consistent with the given magnetospheric electric potential. The model shows that a sheared magnetospheric flow generates current sheets corresponding to upward field-aligned currents, field-aligned potential drops and narrow bands of precipitating energy, as in discrete auroral arcs. Higher velocity magnetospheric sheared flows have the tendency to produce brighter and slightly broader arcs. An increase in arc luminosity is also associated with enhancements of magnetospheric plasma density, in which case the structures are narrower. Finally, the model predicts that an increase of the electron temperature of the magnetospheric flowing plasma corresponds to slightly wider arcs but does not modify their luminosity.

  5. Experimental and theoretical determination of the efficiency of a sub-atmospheric flowing high power cascaded arc hydrogen plasma source

    NARCIS (Netherlands)

    Vijvers, W. A. J.; D.C. Schram,; Shumack, A. E.; Cardozo, N. J. L.; Rapp, J.; van Rooij, G. J.

    2010-01-01

    Cascaded arc plasma sources with channel diameters between 4 and 8mm were experimentally investigated at discharge currents up to 900A and hydrogen (H-2) flow rates up to 10 slm. Pressure measurements at the arc exit showed that the heavy particle temperature in the discharge channel was about 0.8 e

  6. Study of the Material Transfer Characteristics and Surface Morphology Due to Arc Erosion of PtIr Contact Materials

    Institute of Scientific and Technical Information of China (English)

    WANG Saibei; XIE Ming; YANG Youcai; ZHANG Jiming; CHEN Yongtai; LIU Manmen; YANG Yunfeng; HU Jieqiong; CUI Hao

    2012-01-01

    By means of breaking tests on PtIr contact materials via a JF04C contact material testing machine,it was attempted to elucidate the characterstics of the various surface morphology and material transfer after the arc erosion process caused by break arc.The material transfer characteristics appeared in the experiments were concluded and analyzed.Meanwhile,the morphology of the anode and cathode surface were observed and analyzed by SEM.

  7. Experimental Study and Optimisation of Mrr In CNC Plasma ARC Cutting

    Directory of Open Access Journals (Sweden)

    Gurwinder Singh

    2015-06-01

    Full Text Available The research and development in the precise and accurate machining technology of hard metals (Ferrous, nonferrous and glass etc is gaining much importance in the industry since last many years. Due to the tremendous competition and cost factor, the non-conventional machining technology is becoming the first choice of the engineers and technicians. In this era of advanced technological processes the CNC plasma arc machining is gaining tremendous ground in the industry. It is much more capable of producing best finished, high accurate machining of very complicated non-symmetrical profile in no time. The main objective and targets of this practical experiment is based to achieve the best possible setting and parameters of operation on a CNC plasma arc machine to achieving speedy work i.e. Maximum material removal rate.

  8. Plasma centrifuge with vacuum arc discharge applied to the separation of stable isotopes

    Science.gov (United States)

    Delbosco, Edson

    1989-09-01

    The results of a vacuum-arc plasma centrifuge experiment are described. A plasma centrifuge is an apparatus where a plasma column is produced due to the interaction of an electric current with an externally applied magnetic field, vector J x vector B. Among the applications of a rotating plasma, this work deals particularly with its utilization in an isotope enrichment device. The main characteristics of the plasma produced in this experiment are presented, with special attention to the plasma column rotation and the isotope enrichment. The analysis of the results is performed using a fluid model for a completely ionized rigid body rotating plasma column in steady state equilibrium. The main results are: (1) rotation frequency of the plasma column in the range 2 x (exp 4) to 3 x 10 (exp 5) rad/s; (2) enrichment of 10 to 30 pct for the magnesium isotopes, and 290 to 490 pct for the carbon-13 isotope; (3) rigid body rotation of the plasma column only for radii smaller than the characteristic radius of the plasma column, r(sub e); (4) linear dependence of the rotation frequency upon the magnetic field strength only for r is less than r(sub e); (5) existence of an optimum value of the magnetic field for maximum enrichment; and (6) dependence of the rotation frequency upon the inverse of the atomic mass.

  9. Multi-Group Reductions of LTE Air Plasma Radiative Transfer in Cylindrical Geometries

    Science.gov (United States)

    Scoggins, James; Magin, Thierry Edouard Bertran; Wray, Alan; Mansour, Nagi N.

    2013-01-01

    Air plasma radiation in Local Thermodynamic Equilibrium (LTE) within cylindrical geometries is studied with an application towards modeling the radiative transfer inside arc-constrictors, a central component of constricted-arc arc jets. A detailed database of spectral absorption coefficients for LTE air is formulated using the NEQAIR code developed at NASA Ames Research Center. The database stores calculated absorption coefficients for 1,051,755 wavelengths between 0.04 µm and 200 µm over a wide temperature (500K to 15 000K) and pressure (0.1 atm to 10.0 atm) range. The multi-group method for spectral reduction is studied by generating a range of reductions including pure binning and banding reductions from the detailed absorption coefficient database. The accuracy of each reduction is compared to line-by-line calculations for cylindrical temperature profiles resembling typical profiles found in arc-constrictors. It is found that a reduction of only 1000 groups is sufficient to accurately model the LTE air radiation over a large temperature and pressure range. In addition to the reduction comparison, the cylindrical-slab formulation is compared with the finite-volume method for the numerical integration of the radiative flux inside cylinders with varying length. It is determined that cylindrical-slabs can be used to accurately model most arc-constrictors due to their high length to radius ratios.

  10. Modeling of the Flow, Temperature and Concentration Fields in an Arc Plasma Reactor with Argon-Nitrogen Atmosphere

    National Research Council Canada - National Science Library

    Fudolig, Agustin M; Nogami, Hiroshi; Yagi, Jun-ichiro

    1996-01-01

    A mathematical formulation was developed for describing the flow behavior, temperature profile and concentration fields in pure or mixed argon and nitrogen arc plasmas impinging on a metal target inside a reactor...

  11. Numerical Analysis of the Arc Plasma in a Simplified Low-voltage Circuit Breaker Chamber with Ferromagnetic Materials

    Institute of Scientific and Technical Information of China (English)

    Wu Yi; Rong Mingzhe; Yang Qian; Hu Guangxia

    2005-01-01

    This paper is devoted to the simulation of the arc plasma in a simplified low-voltage circuit breaker chamber. Based on a group of coupled governing equations, a three-dimensional (3-D) arc plasma model is built and solved by a modified commercial code. Firstly, this paper presents a solution of the stationary state of the arc plasma and discusses the distribution of some parameters throughout the chamber. Secondly, with the ferromagnetic materials included,the balance of the stationary state is broken and a transient course is calculated. In light of the simulation results, the temperature distribution sequence, the arc motion and the plasma jet are then described and analyzed in detail.

  12. Monitoring Temperature in High Enthalpy Arc-heated Plasma Flows using Tunable Diode Laser Absorption Spectroscopy

    Science.gov (United States)

    Martin, Marcel Nations; Chang, Leyen S.; Jeffries, Jay B.; Hanson, Ronald K.; Nawaz, Anuscheh; Taunk, Jaswinder S.; Driver, David M.; Raiche, George

    2013-01-01

    A tunable diode laser sensor was designed for in situ monitoring of temperature in the arc heater of the NASA Ames IHF arcjet facility (60 MW). An external cavity diode laser was used to generate light at 777.2 nm and laser absorption used to monitor the population of electronically excited oxygen atoms in an air plasma flow. Under the assumption of thermochemical equilibrium, time-resolved temperature measurements were obtained on four lines-of-sight, which enabled evaluation of the temperature uniformity in the plasma column for different arcjet operating conditions.

  13. Contamination due to memory effects in filtered vacuum arc plasma deposition systems

    CERN Document Server

    Martins, D R; Verdonck, P; Brown, I G

    2002-01-01

    Thin film synthesis by filtered vacuum arc plasma deposition is a widely used technique with a number of important emerging technological applications. A characteristic feature of the method is that during the deposition process not only is the substrate coated by the plasma, but the plasma gun itself and the magnetic field coil and/or vacuum vessel section constituting the macroparticle filter are also coated to some extent. If then the plasma gun cathode is changed to a new element, there can be a contamination of the subsequent film deposition by sputtering from various parts of the system of the previous coating species. We have experimentally explored this effect and compared our results with theoretical estimates of sputtering from the SRIM (Stopping and Range of Ions in Matter) code. We find film contamination of order 10-4 - 10-3, and the memory of the prior history of the deposition hardware can be relatively long-lasting.

  14. Closed-loop spontaneous baroreflex transfer function is inappropriate for system identification of neural arc but partly accurate for peripheral arc: predictability analysis.

    Science.gov (United States)

    Kamiya, Atsunori; Kawada, Toru; Shimizu, Shuji; Sugimachi, Masaru

    2011-04-01

    Although the dynamic characteristics of the baroreflex system have been described by baroreflex transfer functions obtained from open-loop analysis, the predictability of time-series output dynamics from input signals, which should confirm the accuracy of system identification, remains to be elucidated. Moreover, despite theoretical concerns over closed-loop system identification, the accuracy and the predictability of the closed-loop spontaneous baroreflex transfer function have not been evaluated compared with the open-loop transfer function. Using urethane and α-chloralose anaesthetized, vagotomized and aortic-denervated rabbits (n = 10), we identified open-loop baroreflex transfer functions by recording renal sympathetic nerve activity (SNA) while varying the vascularly isolated intracarotid sinus pressure (CSP) according to a binary random (white-noise) sequence (operating pressure ± 20 mmHg), and using a simplified equation to calculate closed-loop-spontaneous baroreflex transfer function while matching CSP with systemic arterial pressure (AP). Our results showed that the open-loop baroreflex transfer functions for the neural and peripheral arcs predicted the time-series SNA and AP outputs from measured CSP and SNA inputs, with r2 of 0.8 ± 0.1 and 0.8 ± 0.1, respectively. In contrast, the closed-loop-spontaneous baroreflex transfer function for the neural arc was markedly different from the open-loop transfer function (enhanced gain increase and a phase lead), and did not predict the time-series SNA dynamics (r2; 0.1 ± 0.1). However, the closed-loop-spontaneous baroreflex transfer function of the peripheral arc partially matched the open-loop transfer function in gain and phase functions, and had limited but reasonable predictability of the time-series AP dynamics (r2, 0.7 ± 0.1). A numerical simulation suggested that a noise predominantly in the neural arc under resting conditions might be a possible mechanism responsible for our findings. Furthermore

  15. Development of Energy Efficient, Multi-Channel, Pulsed Plasma Generator for High-Speed Flow Control by Localized Arc Filament Plasma Actuators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The research team at The Ohio State University has been developing technologies to suppress jet noise using localized arc filament plasma actuators and are in the...

  16. Characterization of plasma chemistry and ion energy in cathodic arc plasma from Ti-Si cathodes of different compositions

    Energy Technology Data Exchange (ETDEWEB)

    Eriksson, A. O.; Zhirkov, I.; Dahlqvist, M.; Jensen, J.; Hultman, L.; Rosen, J. [Thin Film Physics Division, Department of Physics, Chemistry and Biology (IFM), Linkoeping University, SE-581 83 Linkoeping (Sweden)

    2013-04-28

    Arc plasma from Ti-Si compound cathodes with up to 25 at. % Si was characterized in a DC arc system with respect to chemistry and charge-state-resolved ion energy. The plasma ion composition showed a lower Si content, diverging up to 12 at. % compared to the cathode composition, yet concurrently deposited films were in accordance with the cathode stoichiometry. Significant contribution to film growth from neutrals is inferred besides ions, since the contribution from macroparticles, estimated by scanning electron microscopy, cannot alone account for the compositional difference between cathode, plasma, and film. The average ion charge states for Ti and Si were higher than reference data for elemental cathodes. This result is likely related to TiSi{sub x} phases of higher cohesive energies in the compound cathodes and higher effective electron temperature in plasma formation. The ion energy distributions extended up to {approx}200 and {approx}130 eV for Ti and Si, respectively, with corresponding average energies of {approx}60 and {approx}30 eV. These averages were, however, not dependent on Si content in the cathode, except for 25 at. % Si where the average energies were increased up to 72 eV for Ti and 47 eV for Si.

  17. Formation of NOx precursors during Chinese pulverized coal pyrolysis in an arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Wei-ren Bao; Jin-cao Zhang; Fan Li; Li-ping Chang [Taiyuan University of Technology, Taiyuan (China). Key Laboratory of Coal Science and Technology

    2007-08-15

    The formation of NOx precursors (HCN and NH{sub 3}) from the pyrolysis of several Chinese pulverized coals in an arc plasma jet was investigated through both thermodynamic analysis of the C-H-O-N system and experiments. Results of thermodynamic analysis show that the dominant N-containing gaseous species is HCN together with a small amount of ammonia above the temperature of 2000 K. The increase of H content advances the formation of HCN and NH{sub 3}, but the yields of HCN and NH{sub 3} are decreased with a high concentration of O in the system. These results are accordant with the experimental data. The increasing of input power promotes the formation of HCN and NH{sub 3} from coal pyrolysis in an arc plasma jet. Tar-N is not formed during the process. The yield of HCN changes insignificantly with the changing of the residence time of coal particles in the reactor, but that of NH{sub 3} decreases as residence times increase because of the relative instability at high temperature. Adsorption and gasification of CO{sub 2} on the coal surface also can restrain the formation of HCN and NH{sub 3} compare to the results in an Ar plasma jet. Yields of HCN and NH{sub 3} are sensitive to the coal feeding rate, indicating that NOx precursors could interact with the nascent char to form other N-containing species. The formation of HCN and NH{sub 3} during coal pyrolysis in a H{sub 2}/Ar plasma jet are not dependent on coal rank. The N-containing gaseous species is released faster than others in the volatiles during coal pyrolysis in an arc plasma jet, and the final nitrogen content in the char is lower than that in the parent coal, which it is independent of coal type. 16 refs., 9 figs., 1 tab.

  18. Preparation of carbon nanoparticles by plasma arc discharge under fluidized dynamic equilibrium

    Science.gov (United States)

    Wang, F.; Sun, D. L.; Hong, R. Y.; Kumar, M. R.

    2016-06-01

    Continuous preparation of carbon nanoparticles by dielectric barrier discharge (DBD)-induced non-thermal plasma arc discharge with large spacing in a modified fluidized bed is presented. Discharge arc is generated via the inducement of DBD which provides conductive media in order to realize a large spacing arc discharge. Three kinds of flow conditions defined as full circulation, fluidized dynamic equilibrium, and full collection are determined by the relationship of critical fluidized velocity and the real gas velocity after some modification of the fluidized bed. Movement model of carbon nanoparticles has been proposed to illustrate the flow conditions. A visualized and comprehensive refinement of aggregating processes has been exhibited and proved by high-resolution transmission electron microscopy. Simplified equivalent electrical conductive model of the arc discharge system is successful to generally and perspicuously figure out the discharge process which is impeded by the generated carbon nanoparticles. Effects of flow conditions and flow ratio of carrier gas/carbon source on morphology and yield of nanoparticles have been analyzed by morphology observation and yield calculation along with modeling the process.

  19. The influence of the arc plasma treatment on the structure and microhardness C120U carbon tool steel

    Directory of Open Access Journals (Sweden)

    W. Bochnowski

    2010-01-01

    Full Text Available paper. They are compared with the properties obtained after conventional hardening. The GTAW (Gas Tungsten Arc Welding method was used. The remelted zone consists of dendritic cells and columnar crystals. Inside the columnar crystals dependent to current arc plasma intensity the martensite or lower bainite was observed. The cooling rate of the remelted zone is similar to the cooling rate obtained in the classical heat treatment. The maximum hardness 650 HV0,1 was measured in material after treatment with a smaller current intensity of arc plasma – 60A. Increases of the current intensity of arc plasma from 60 A to 110 A (for fixed speed rate of source lead to increases the depth of the remelted zone from 1,2 to 3,1 mm. Thickness of the heat affected zone in the all specimens was similar (1,9 to 2,1 mm.

  20. Plasma arc cutting optimization parameters for aluminum alloy with two thickness by using Taguchi method

    Science.gov (United States)

    Abdulnasser, B.; Bhuvenesh, R.

    2016-07-01

    Manufacturing companies define the qualities of thermal removing process based on the dimension and physical appearance of the cutting material surface. The surface roughness of the cutting area for the material and the material removal rate being removed during the manual plasma arc cutting process were importantly considered. Plasma arc cutter machine model PS-100 was used to cut the specimens made from aluminium alloy 1100 manually based on the selected parameters setting. Two different thicknesses of specimens, 3mm and 6mm were used. The material removal rate (MRR) was measured by determining the difference between the weight of specimens before and after the cutting process. The surface roughness (Ra) was measured by using MITUTOYO CS-3100 machine and analysis was conducted to determine the average roughness (Ra) value, Taguchi method was utilized as an experimental layout to obtain MRR and Ra values. The results indicate that the current and cutting speed is the most significant parameters, followed by the arc gap for both rate of material removal and surface roughness.

  1. Fatigue cracking of hybrid plasma gas metal arc welded 2205 duplex stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Yurtisik, Koray; Tirkes, Suha [Middle East Technical Univ., Ankara (Turkey). Welding Technology and Nondestructive Testing Research/Application Center

    2014-10-01

    Contrary to other keyhole welding applications on duplex stainless steels, a proper cooling time and a dilution were achieved during hybrid plasma gas metal arc welding that provided sufficient reconstructive transformation of austenite without sacrificing its high efficiency and productivity. Simultaneous utilization of keyhole and metal deposition in the hybrid welding procedure enabled us to get an as-welded 11 mm-thick standard duplex stainless steel plate in a single pass. Metallographic examination on hybrid plasma-gas metal arc weldments revealed only primary austenite in ferrite matrix, whereas in addition to reconstructive transformation of primary austenite during solidification, secondary austenite was also transformed in a displacive manner due to successive thermal cycles during multi-pass gas metal arc welding. On the one hand, secondary austenite provided barriers and retarded the crack propagation during the tests in laboratory air. On the other hand, chromium and molybdenum depletion in the neighborhood of secondary austenite precipitates yielded relatively high crack propagation rates in multi-pass weldments under chloride attack.

  2. The determination of micro-arc plasma composition and properties of nanoparticles formed during cathodic plasma electrolysis of 304 stainless steel

    Science.gov (United States)

    Jovović, Jovica; Stojadinović, Stevan; Vasilić, Rastko; Tadić, Nenad; Šišović, Nikola M.

    2017-05-01

    This paper presents the research focused on the determination of micro-arc plasma composition during cathodic plasma electrolysis of AISI304 stainless steel in water solution of sodium hydroxide. The complex line shape of several Fe I spectral lines was observed and, by means of a dedicated fitting procedure based on the spectral line broadening theory and H2O thermal decomposition data, the mole fraction of micro-arc plasma constituents (H2, Fe, O, H, H2O, and OH) was determined. Subsequent characterization of the cathodic plasma electrolysis product formed during the process revealed that it consists of Fe-nanoparticles with median diameter of approximately 60 nm.

  3. Rocket measurements within a polar cap arc - Plasma, particle, and electric circuit parameters

    Science.gov (United States)

    Weber, E. J.; Ballenthin, J. O.; Basu, S.; Carlson, H. C.; Hardy, D. A.; Maynard, N. C.; Kelley, M. C.; Fleischman, J. R.; Pfaff, R. F.

    1989-01-01

    Results are presented from the Polar Ionospheric Irregularities Experiment (PIIE), conducted from Sondrestrom, Greenland, on March 15, 1985, designed for an investigation of processes which lead to the generation of small-scale (less than 1 km) ionospheric irregularities within polar-cap F-layer auroras. An instrumented rocket was launched into a polar cap F layer aurora to measure energetic electron flux, plasma, and electric circuit parameters of a sun-aligned arc, coordinated with simultaneous measurements from the Sondrestrom incoherent scatter radar and the AFGL Airborne Ionospheric Observatory. Results indicated the existence of two different generation mechanisms on the dawnside and duskside of the arc. On the duskside, parameters are suggestive of an interchange process, while on the dawnside, fluctuation parameters are consistent with a velocity shear instability.

  4. Cathodic arcs

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre

    2003-10-29

    Cathodic arc plasma deposition has become the technology of choice for hard, wear and corrosion resistant coatings for a variety of applications. The history, basic physics of cathodic arc operation, the infamous macroparticle problem and common filter solutions, and emerging high-tech applications are briefly reviewed. Cathodic arc plasmas standout due to their high degree of ionization, with important consequences for film nucleation, growth, and efficient utilization of substrate bias. Industrial processes often use cathodic arc plasma in reactive mode. In contrast, the science of arcs has focused on the case of vacuum arcs. Future research directions include closing the knowledge gap for reactive mode, large area coating, linear sources and filters, metal plasma immersion process, with application in high-tech and biomedical fields.

  5. Silica nanoparticles produced by DC arc plasma from a solid raw materials

    Science.gov (United States)

    Kosmachev, P. V.; Vlasov, V. A.; Skripnikova, N. K.

    2017-05-01

    Plasma synthesis of SiO2 nanoparticles in experimental atmospheric pressure plasma reactor on the basis of DC arc plasma generator was presented in this paper. Solid high-silica raw materials such as diatomite from Kamyshlovskoye deposit in Russia, quartzite from Chupinskoye deposit in Russia and milled window glass were used. The obtained nanoparticles were characterized based on their morphology, chemical composition and size distribution. Scanning electron microscopy, laser diffractometry, nitrogen absorption (Brunauer-Emmett-Teller method), X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy were used to characterize the synthesized products. The obtained silica nanoparticles are agglomerated, have spherical shape and primary diameters between 10-300 nm. All samples of synthesized nanopowders were compared with commercial nanopowders.

  6. Rotational and Vibrational Temperatures of Atmospheric Double Arc Argon-Nitrogen Plasma

    Institute of Scientific and Technical Information of China (English)

    YAN Jian-Hua; TU Xin; MA Zeng-Yi; CEN Ke-Fa; B.G.Chéron

    2007-01-01

    The spectroscopic technique is employed to study the emission of atmospheric argon-nitrogen plasma jet generated by an original dc double anode plasma torch. The molecular bands of the N(+2) first negative system are observed at the torch exit and chosen to evaluate the rotational and vibrational temperatures in comparison with the simulated spectra. The excitation temperature (Texc≈9600 K) is determined from the Boltzmann plot method. The results show that the rotational, vibrational, electron and kinetic temperatures are in good agreement with one another, which indicates that the core region of atmospheric double arc argon-nitrogen plasma jet at the torch exit is close to the local thermodynamic equilibrium state under our experimental conditions.

  7. Performance of water and hybrid stabilized electric arcs: the impact of dependence of radiation losses and plasma density on pressure

    Science.gov (United States)

    Jeništa, J.; Bartlová, M.; Aubrecht, V.

    2006-10-01

    Processes in the worldwide unique type of thermal plasma generator with water vortex stabilization and combined stabilization of arc by argon flow and water vortex have been numerically studied. Two-dimensional axisymmetric numerical model assumes laminar and compressible plasma flow in the state of local thermodynamic equilibrium. The calculation domain includes the arc discharge area between the near-cathode region and the outlet nozzle of the plasma torch. Radiation losses from the arc are calculated by the partial characteristics method for atmospheric pressure water and argon-water discharges. Thermal, electrical and fluid-dynamic characteristics of such arcs have been studied for the range of currents 150÷600 A under the assumption that radiation losses and plasma density depend linearly on pressure. It was proved that, taking this dependence into account, plasma velocity decrease while power losses from the arc by radiation and radial conduction increase with current. Outlet plasma temperature as well as electric potential drop remain practically unchanged.

  8. Cathodic arcs

    OpenAIRE

    Anders, Andre

    2003-01-01

    Cathodic arc plasma deposition has become the technology of choice for hard, wear and corrosion resistant coatings for a variety of applications. The history, basic physics of cathodic arc operation, the infamous macroparticle problem and common filter solutions, and emerging high-tech applications are briefly reviewed. Cathodic arc plasmas stand out due to their high degree of ionization, with important consequences for film nucleation, growth, and efficient utilization of substrate bia...

  9. Influence of residual plasma drift velocity on the post-arc sheath expansion of vacuum circuit breakers

    Energy Technology Data Exchange (ETDEWEB)

    Mo, Yongpeng; Shi, Zongqian; Jia, Shenli; Wang, Lijun [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an, Shaanxi 710049 (China); Bai, Zhibin [State Grid Yulin Electric Power Supply Company, Shaanxi 719000 (China)

    2016-05-15

    The residual plasma in the inter-contact region of a vacuum circuit breaker moves towards the post-arc cathode at current zero, because the residual plasma mainly comes from the cathode spots during the arc burning process. In the most previous theoretical researches on the post-arc sheath expansion process of vacuum circuit breakers, only the thermal motion of residual plasma was taken into consideration. Alternately, the residual plasma was even assumed to be static at the moment of current zero in some simplified models. However, the influence of residual plasma drift velocity at current zero on the post-arc sheath expansion process was rarely investigated. In this paper, this effect is investigated by a one-dimensional particle-in-cell model. Simulation results indicate that the sheath expands slower with higher residual plasma drift velocity in the initial sheath expansion stage. However, with the increase of residual plasma drift velocity, the overall plasma density in the inter-contact region decreases faster, and the sheath expansion velocity increases earlier. Consequently, as a whole, it needs shorter time to expel the residual plasma from the inter-contact region. Furthermore, if the residual plasma drift velocity is high enough, the sheath expansion process ceases before it develops to the post-arc anode. Besides, the influence of the collisions between charges and neutrals is investigated as well in terms of the density of metal vapor. It shows that the residual plasma drift velocity takes remarkable effect only if the density of the metal vapor is relatively low, which corresponds to the circumstance of low-current interruptions.

  10. Influence of residual plasma drift velocity on the post-arc sheath expansion of vacuum circuit breakers

    Science.gov (United States)

    Mo, Yongpeng; Shi, Zongqian; Bai, Zhibin; Jia, Shenli; Wang, Lijun

    2016-05-01

    The residual plasma in the inter-contact region of a vacuum circuit breaker moves towards the post-arc cathode at current zero, because the residual plasma mainly comes from the cathode spots during the arc burning process. In the most previous theoretical researches on the post-arc sheath expansion process of vacuum circuit breakers, only the thermal motion of residual plasma was taken into consideration. Alternately, the residual plasma was even assumed to be static at the moment of current zero in some simplified models. However, the influence of residual plasma drift velocity at current zero on the post-arc sheath expansion process was rarely investigated. In this paper, this effect is investigated by a one-dimensional particle-in-cell model. Simulation results indicate that the sheath expands slower with higher residual plasma drift velocity in the initial sheath expansion stage. However, with the increase of residual plasma drift velocity, the overall plasma density in the inter-contact region decreases faster, and the sheath expansion velocity increases earlier. Consequently, as a whole, it needs shorter time to expel the residual plasma from the inter-contact region. Furthermore, if the residual plasma drift velocity is high enough, the sheath expansion process ceases before it develops to the post-arc anode. Besides, the influence of the collisions between charges and neutrals is investigated as well in terms of the density of metal vapor. It shows that the residual plasma drift velocity takes remarkable effect only if the density of the metal vapor is relatively low, which corresponds to the circumstance of low-current interruptions.

  11. Advanced plasma flow simulations of cathodic-arc and ferroelectric plasma sources for neutralized drift compression experiments

    Directory of Open Access Journals (Sweden)

    Adam B. Sefkow

    2008-07-01

    Full Text Available Large-space-scale and long-time-scale plasma flow simulations are executed in order to study the spatial and temporal evolution of plasma parameters for two types of plasma sources used in the neutralized drift compression experiment (NDCX. The results help assess the charge neutralization conditions for ion beam compression experiments and can be employed in more sophisticated simulations, which previously neglected the dynamical evolution of the plasma. Three-dimensional simulations of a filtered cathodic-arc plasma source show the coupling efficiency of the plasma flow from the source to the drift region depends on geometrical factors. The nonuniform magnetic topology complicates the well-known general analytical considerations for evaluating guiding-center drifts, and particle-in-cell simulations provide a self-consistent evaluation of the physics in an otherwise challenging scenario. Plasma flow profiles of a ferroelectric plasma source demonstrate that the densities required for longitudinal compression experiments involving ion beams are provided over the drift length, and are in good agreement with measurements. Simulations involving azimuthally asymmetric plasma creation conditions show that symmetric profiles are nevertheless achieved at the time of peak on-axis plasma density. Also, the ferroelectric plasma expands upstream on the thermal expansion time scale, and therefore avoids the possibility of penetration into the acceleration gap and transport sections, where partial neutralization would increase the beam emittance. Future experiments on NDCX will investigate the transverse focusing of an axially compressing intense charge bunch to a sub-mm spot size with coincident focal planes using a strong final-focus solenoid. In order to fill a multi-tesla solenoid with the necessary high-density plasma for beam charge neutralization, the simulations predict that supersonically injected plasma from the low-field region will penetrate and

  12. Investigation of firing properties of a vacuum arcs triggered by plasma injection

    Energy Technology Data Exchange (ETDEWEB)

    Bernardet, H.; Godechot, X.; Riviere, C. [SODERN, Limeil-Brevannes (France)

    1996-08-01

    The firing characteristic of a vacuum arc, by means of plasma injection, is described. In this method, a plasma, created from a trigger device, plumes away to the space between the cathode and anode. As the plasma is quasi-neutral, the electrostatic field is concentrated across the sheath at the surface of the cathode, thus, creating a high electrical field. As a result, a vacuum arc fires between the cathode and anode. The authors have investigated the firing rate as a function of the trigger cathode distance, trigger current, the anode-cathode distance and voltage. They found a firing rate between 90 to 100% for a trigger current in the range of 400-1200 A, the trigger pulse length was 4 ps, and the trigger-cathode distance was 1.6 to 3.6 cm. The anode cathode gap length changes the firing rate to a low extent for values between 2 to 5 cm. The anode cathode voltage do not change the firing rate. The effect of a magnetic field applied axially over the trigger have also been investigated. Using a version of a highly reliable trigger, the authors were able to deposit stainless steel, copper, carbon and molybdenum, thin films.

  13. Ultra-small platinum and gold nanoparticles by arc plasma deposition

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sang Hoon, E-mail: kim_sh@kist.re.kr [Center for Materials Architecturing, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Jeong, Young Eun; Ha, Heonphil; Byun, Ji Young [Center for Materials Architecturing, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Kim, Young Dok [Department of Chemistry, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2014-04-01

    Highlights: • Ultra-small (<2 nm) and bigger platinum and gold nanoparticles were produced by arc plasma deposition (APD). • Size and coverage of deposited nanoparticles were easily controlled with APD parameters. • Crystalline structures of deposited nanoparticles emerged only when the particle size was bigger than ∼2 nm. - Abstract: Ultra-small (<2 nm) nanoparticles of platinum and gold were produced by arc plasma deposition (APD) in a systematic way and the deposition behavior was studied. Nanoparticles were deposited on two dimensional amorphous carbon and amorphous titania thin films and characterized by transmission electron microscopy (TEM). Deposition behavior of nanoparticles by APD was studied with discharge voltage (V), discharge condenser capacitance (C), and the number of plasma pulse shots (n) as controllable parameters. The average size of intrinsic nanoparticles generated by APD process was as small as 0.9 nm and deposited nanoparticles began to have crystal structures from the particle size of about 2 nm. V was the most sensitive parameter to control the size and coverage of generated nanoparticles compared to C and n. Size of APD deposited nanoparticles was also influenced by the nature of evaporating materials and substrates.

  14. Pyrolysis of Polyolefins Using Rotating Arc Plasma Technology for Production of Acetylene

    Directory of Open Access Journals (Sweden)

    Ming Zhang

    2017-04-01

    Full Text Available Polyolefin, as one of the most widely used macromolecule materials, has been one of the most serious threats to the environment. Current treatment methods of waste polyolefin including landfill, incineration, and thermal degradation have suffered from severe problems such as secondary pollution and the generation of other toxic substances. In this article, we report for the first time a high-efficiency method to produce high-value C2H2 from polyolefins using a rotating direct current arc plasma reactor, using polyethylene and polypropylene as feedstocks. The essence of this method is that a reductive atmosphere of pyrolysis enables a thermodynamic preference to C2H2 over other carbon-containing gas and the rotating direct current arc plasma reactor allows for a uniform distribution of high temperature to ensure high conversion of polymers. Thermodynamic simulation of product composition was performed, and the effect of plasma input power, polyolefin feed rate, and working gas flow rate on the pyrolysis results was experimentally investigated. It was found that, with proper parameter control, approximately complete conversion of carbon in polyolefin could be obtained, with a C2H2 selectivity higher than 80% and a C2H2 yield higher than 70%. These results not only create new opportunities for the reuse of polymer waste, but are also instructive for the green production of C2H2.

  15. Wear Resistance of In-situ Fe-Cr-V-C Hardfacing Alloys Fabricated by Plasma Transferred Arc Weld-surfacing Process%等离子原位合成Fe-Cr-V-C堆焊合金的耐磨性

    Institute of Scientific and Technical Information of China (English)

    宗琳; 刘政军; 李乐成

    2012-01-01

    采用等离子堆焊技术制备了不同Cr含量的Fe-Cr-V-C堆焊合金,借助扫描电镜和X射线衍射等分析手段研究了碳化物形貌及合金物相组成.同时研究了Cr含量对合金硬度和耐磨性的影响,并探讨了磨损机理.结果表明:堆焊合金组织由马氏体、铁素体、奥氏体、M7C3及VC组成.合金中随着Cr含量的提高,由于硬质相M7C3和VC的数量及形态变化不大,而具有高硬度的针状马氏体基体组织的减少使得合金的耐磨性先降低,当达到一定值后继续增加Cr含量,M7C3的数量逐渐增多,因而耐磨性随后增大;当Cr含量达到27.2%(质量分数)时,大量高硬度六边形M7C3复合物(约HV1200)结合一定量VC(约HV1600)颗粒构成坚实的耐磨骨架,使得合金具有最佳的耐磨性.%Fe-Cr-V-C hardfacing alloys with different Cr contents were prepared under plasma transferred arc (PTA). The phases constitution, carbide morphology were investigated by means of scanning electron microscopy(SEM) and X-ray diffraction (XRD). The effect of Cr contents on the wear resistance of hardfacing alloys was detected by using Rockwell hardometer and wear testing machine. In addition, the abrasion wear mechanism was discussed. The results show that the microstructure consists of martensite, ferrite and austenite, carbides such as primary M7C3, VC. As the Cr contents increase, the wear resistance first decreases because of the little changes of content and morphology for M7C3 and VC hard phases and the decrease of acicular martensite with high hardness, afterwards, the wear resistance increases when Cr content reaches a particular value as a result of the increase of M7C3 contents. When Cr mass fraction is 27. 2%, a high volume fraction of hexagonal (Fe,Cr,V)rC3 complex carbides and a small amount globular VC particles in the microstructure form a substantial wear resistant structure, which leads to an excellent wear resistance.

  16. Arc-plasma spraying and suctioncasting methods in magnetic materials manufacturing

    Directory of Open Access Journals (Sweden)

    J.J. Wysłocki

    2010-11-01

    Full Text Available Purpose: The paper discusses two new technologies for producing magnetic materials which have been successfully developed in recent years at the Institute of Physics of the Czestochowa University of Technology and discusses properties of the materials obtained with the use of these methods.Design/methodology/approach: In this research the arc-plasma deposition of Nd2Fe14B powders onto a substrate either cooled with water or heated up to a temperature in the range from 773 to1023 K was applied. In the second method the suction of an arc-melted alloy to a water-cooled copper mould (the suction-casting method was introduced. Moreover, microstructure, magnetic properties and domain structure of the produced samples were determined.Findings: It has been found that thin Nd2Fe14B strips obtained by the plasma method possess magnetic properties. It has also been demonstrated that the suction-casting method makes it possible to obtain both amorphous magnetically soft materials (e.g. Fe-Co-W-Zr-B, as well as magnetically hard nanocomposites (e.g. (Fe-Co-(Pr-Dy-B-Zr.Research limitations/implications: The main problem in the suction-casting method is to reduce the critical cooling rate required for the production of amorphous alloys and to increase the geometrical dimensions of amorphous specimens.Practical implications: Thin-layered Nd-Fe-B magnets produced by means of arc-plasma deposition can be applied directly onto the surface of electromagnetic equipment parts. Magnets with isotropic magnetic properties were obtained by applying layers onto the water-cooled copper substrate. Whereas, anisotropic magnets were obtained as a result of the arc-plasma deposition of powders onto the copper substrate heated up to 873 K. The most advantageous properties were achieved for the microcrystalline structure of a grain size close to the single-domain particle size (approx. 0.3 μm. Moreover, it has been demonstrated that the suction-casting method makes it possible

  17. Fabrication and characterization of TiN nanocomposite powders fabricated by DC arc-plasma method

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, K., E-mail: kaneko@zaiko.kyushu-u.ac.j [Department of Materials Science and Engineering, Graduate School of Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); JST-CREST (Japan); Kitawaki, K. [Department of Materials Science and Engineering, Graduate School of Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Sadayama, S. [FEI Company Japan Ltd., NSS-II Bldg 1F, 13-34 Kohnan 2-chome, Minato-ku, Tokyo 108-0075 (Japan); Razavi, H. [Department of Materials Science and Engineering, Graduate School of Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Hernandez-Garrido, J.C.; Midgley, P.A. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); Okuyama, H.; Uda, M. [Nano Ceramics Center, National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Sakka, Y. [Nano Ceramics Center, National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaraki 305-0047 (Japan); WPI Center for MANA, National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, Ibaraki 305-0047 (Japan)

    2010-03-04

    TiN nanocomposite powders with various morphologies were synthesized by DC arc-plasma method from Ti-Si ingot under N{sub 2}-H{sub 2}-Ar atmosphere. Microstructures of powders were characterized by powder X-ray diffraction method and transmission electron microscopy with compositional analysis, then morphologies by three-dimensional electron tomography. It was found that the powders were consisted of TiN nanoparticles covered by Ti{sub 5}Si{sub 3} nanoparticles, which possibly suppressed the growth of facets and controlled the final morphologies of TiN-Ti{sub 5}Si{sub 3} nanocomposite.

  18. Characterization and Photoluminescence Properties of Alumina Nanowires Elaborated by Arc-Plasma

    Institute of Scientific and Technical Information of China (English)

    C. Arnoult; X. Devaux; H. Rinnert; M. Vergnat

    2006-01-01

    Ultrafine powders containing alumina nanowires are synthesized by DC arc plasma from pure aluminium metal.Nanowires grow only when reactive gases are composed of nitrogen and less than ten percent of oxygen.Nanowires have the diameters ranging from 20 to 80 nm and lengths ranging from hundreds nanometers to tens of micrometers. A first assumption of the mechanism process is proposed, in which nanowires grow starting directly from the aluminium. Photoluminescence measurements show that the powders have three emission peaks around 435,530 and 750 nm resulting from different kinds of defects such as oxygen vacancies,aluminium interstitial ions and surface defects.

  19. Literature review of arc/plasma, combustion, and joule-heated melter vitrification systems

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, C.J.; Abrigo, G.P.; Shafer, P.J.; Merrill, R.A.

    1995-07-01

    This report provides reviews of papers and reports for three basic categories of melters: arc/plasma-heated melters, combustion-heated melters, and joule-heated melters. The literature reviewed here represents those publications which may lend insight to phase I testing of low-level waste vitrification being performed at the Hanford Site in FY 1995. For each melter category, information from those papers and reports containing enough information to determine steady-state mass balance data is tabulated at the end of each section. The tables show the composition of the feed processed, the off-gas measured via decontamination factors, gross energy consumptions, and processing rates, among other data.

  20. Cell adhesion property of cathodic arc plasma deposited CrN thin film

    Science.gov (United States)

    Kim, Sun Kyu; Pham, Vuong Hung

    2009-09-01

    The interaction between human osteoblast cells and CrN thin film was studied in vitro. CrN thin films were produced by cathodic arc plasma deposition. The surface was characterized by atomic force microscopy. Cell adhesion on the coatings was assessed by MTT assay and visualization. Cell cytoskeleton organization was studied by analyzing microtubule and actin cytoskeleton organization. Focal contact adhesion was monitored by analyzing vinculin density. The study found that the CrN thin film is a potential candidate as a protective coating on implantable devices that require minimal cellular adhesion.

  1. Characterization of Ni ferrites powders prepared by plasma arc discharge process

    Science.gov (United States)

    Safari, A.; Gheisari, Kh.; Farbod, M.

    2017-01-01

    The aim of this work was to synthesize a single-phase spinel structure from a mixture of zinc, iron and nickel powders by plasma arc discharge method. A mixture of zinc, iron and nickel powders with the appropriate molar ratio was prepared and formed into a cylindrical shape. The synthesis process was performed in air, oxygen and argon atmospheres with the applied arc current of 400 A and pressure of 1 atm. After establishing an arc between the electrodes, the produced powders were collected and their structure and magnetic properties were examined by XRD and VSM, respectively. ZnO as an impurity was appeared in the as-produced powders owing to the high reactivity of zinc atoms, preventing the formation of Ni-Zn ferrite. A pure spinel structure with the highest saturation magnetization (43.8 emu/g) was observed as zinc powders removed completely from the initial mixture. Morphological evaluations using field emission scanning electron microscopy showed that the mean size of fabricated nanoparticles was in the range 100-200 nm and was dependent on the production conditions.

  2. Structural evolution of Ti destroyable interlayer in large-size diamond film deposition by DC arc plasma jet

    Science.gov (United States)

    Guo, Jianchao; Li, Chengming; Liu, Jinlong; Wei, Junjun; Chen, Liangxian; Hua, Chenyi; Yan, Xiongbo

    2016-05-01

    The addition of titanium (Ti) interlayer was verified to reduce the residual stress of diamond films by self-fracturing and facilitate the harvest of a crack-free free-standing diamond film prepared by direct current (DC) arc plasma jet. In this study, the evolution of the Ti interlayer between large-area diamond film and substrate was studied and modeled in detail. The evolution of the interlayer was found to be relevant to the distribution of the DC arc plasma, which can be divided into three areas (arc center, arc main, and arc edge). The formation rate of titanium carbide (TiC) in the arc main was faster than in the other two areas and resulted in the preferred generation of crack in the diamond film in the arc main during cooling. Sandwich structures were formed along with the growth of TiC until the complete transformation of the Ti interlayer. The interlayer released stress via self-fracture. Avoiding uneven fragile regions that formed locally in the interlayer and achieving cooperatively released stress are crucial for the preparation of large crack-free diamond films.

  3. Effects of anchoring and arc structure on the control authority of a rail plasma actuator

    Science.gov (United States)

    Choi, Young-Joon; Gray, Miles; Sirohi, Jayant; Raja, Laxminarayan L.

    2017-09-01

    Experiments were conducted on a rail plasma actuator (RailPAc) with different electrode cross sections (rails or rods) to assess methods to improve the actuation authority, defined as the impulse generated for a given electrical input. The arc was characterized with electrical measurements and high-speed images, while impulse measurements quantified the actuation authority. A RailPAc power supply capable of delivering  ∼1 kA of current at  ∼100 V was connected to rod electrodes (free-floating with circular cross-section) and rail electrodes (flush-mounted in a flat plate with rectangular cross-section). High-speed images show that the rail electrodes cause the arc to anchor itself to the anode electrode and transit in discrete jumps, while rod electrodes permit the arc to transit smoothly without anchoring. The impulse measurements reveal that the anchoring reduces the actuation authority by  ∼21% compared to a smooth transit, and the effect of anchoring can be suppressed by reducing the gap between the rails to 2 mm. The study further demonstrates that if a smooth transit is achieved, the control authority can be increased with a larger gap and larger arc current. In conclusion, the actuation authority of a RailPAc can be maximized by carefully choosing a gap width that prevents anchoring. Further study is warranted to increase the RailPAc actuation authority by introducing multiple turns of wires beneath the RailPAc to augment the induced magnetic field.

  4. Feasibility of arc-discharge and plasma-sputtering methods in cleaning plasma-facing and diagnostics components of fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hakola, Antti, E-mail: antti.hakola@vtt.fi [VTT Technical Research Centre of Finland, VTT (Finland); Likonen, Jari [VTT Technical Research Centre of Finland, VTT (Finland); Karhunen, Juuso; Korhonen, Juuso T. [Department of Applied Physics, Aalto University (Finland); Aints, Märt; Laan, Matti; Paris, Peeter [Department of Physics, University of Tartu (Estonia); Kolehmainen, Jukka; Koskinen, Mika; Tervakangas, Sanna [DIARC-Technology Oy, Espoo (Finland)

    2015-10-15

    Highlights: • Feasibility of the arc-discharge and plasma-sputtering techniques in removing deposited layers from ITER-relevant samples demonstrated. • Samples with the size of an A4 paper can be cleaned from 1-μm thick deposited layers in 10–20 minutes by the arc-discharge method. • The plasma-sputtering method is 5–10 times slower but the resulting surfaces are very smooth. • Arc-discharge method could be used for rapid cleaning of plasma-facing components during maintenance shutdowns of ITER, plasma sputtering is preferred for diagnostics mirrors. - Abstract: We have studied the feasibility of arc-discharge and plasma-sputtering methods in removing deposited layers from ITER-relevant test samples. Prototype devices have been designed and constructed for the experiments and the cleaning process is monitored by a spectral detection system. The present version of the arc-discharge device is capable of removing 1-μm thick layers from 350-mm{sup 2} areas in 4–8 s, but due to the increased roughness of the cleaned surfaces and signs of local melting, mirror-like surfaces cannot be treated by this technique. The plasma-sputtering approach, for its part, is some 5–10 times slower in removing the deposited layers but no changes in surface roughness or morphology of the samples could be observed after the cleaning phase. The arc-discharge technique could therefore be used for rapid cleaning of plasma-facing components during maintenance shutdowns of ITER while in the case of diagnostics mirrors plasma sputtering is preferred.

  5. Oxygen plasma-treatment effects on Si transfer.

    Science.gov (United States)

    Langowski, Bryan A; Uhrich, Kathryn E

    2005-07-05

    Oxygen plasma-treatment is commonly used to increase the hydrophilicity of poly(dimethylsiloxane) (PDMS) stamps used for microcontact printing (muCP) aqueous-based inks. Review of the literature reveals that a wide range of plasma parameters are currently employed to modify stamp surfaces. However, little is known about the effect of these parameters (e.g., power, chamber pressure, duration) on the undesirable transfer of low-molecular-weight silicon-containing fragments from the stamps that commonly occurs during muCP. To study the effect of oxygen plasma-treatment on Si transfer, unpatterned PDMS stamps were treated with oxygen plasma under various conditions and used to stamp deionized water on plasma-activated poly(methyl methacrylate) (PMMA) substrates. Once stamped, the PMMA substrates were analyzed with X-ray photoelectron spectroscopy (XPS) to quantify and characterize silicon present on the substrate surface. In addition, used PDMS stamps were analyzed with scanning electron microscopy (SEM) to observe topographical changes that occur during oxygen plasma-treatment. XPS results show that all plasma treatments studied significantly reduced the amount of Si transfer from the treated stamps during muCP as compared to untreated PDMS stamps and that the source of transfer is residual PDMS fragments not removed by oxygen plasma. SEM results show that, although the treated stamps undergo a variety of topographical changes, no correlation exists between stamp topography and extent of Si transfer from the stamps.

  6. Demonstration of Plasma Arc Environmental Technology Applications for the Demilitarization of DOD Stockpiles

    Science.gov (United States)

    Smith, Ed; Zaghloul, Hany; Filius, Krag; Rivers, Tim

    2000-01-01

    Since 1989 the U.S. Army Construction Engineering Research Laboratories (USACERL) have been active participants in the research and development toward establishing Plasma Arc Technology (PAT) as an efficient, economical, and safe hazardous waste immobilization tool. A plasma torch capable of generating high temperatures makes this technology a viable and powerful tool for the thermal destruction of various military industrial waste streams into an innocuous ceramic material no longer requiring hazardous waste landfill (Class 1) disposal. The emerging pl asma environmental thermal treatment process, has been used to safely and efficiently meet the waste disposal needs for various demilitarized components disposal needs, such as: pyrotechnic smoke assemblies, thermal batteries, proximity fuses, cartridge actuated devices (CAD's), and propellant actuated devices (PAD's). MSE Technology Applications, Inc., (MSE) has proposed and fabricated a Mobile Plasma Treatment System to be a technology demonstrator for pilot-scale mobile plasma waste processing. The system is capable of providing small-scale waste remediation services, and conducting waste stream applicability demonstrations. The Mobile Plasma Treatment System's innovative concept provides the flexibility to treat waste streams at numerous sites and sites with only a limited quantity of waste, yet too hazardous to transport to a regional fixed facility. The system was designed to be operated as skid mounted modules; consisting of a furnace module, controls module, offgas module, and ancillary systems module. All system components have been integrated to be operated from a single control station with both semi-continuous feeding and batch slag-pouring capability.

  7. Lowering of plasma phospholipid transfer protein activity by acute hyperglycaemia-induced hyperinsulinaemia in healthy men

    NARCIS (Netherlands)

    vanTol, A; Ligtenberg, JJM; Riemens, SC; vanHaeften, TW; Dullaart, RPF

    1997-01-01

    Human plasma contains two lipid transfer proteins involved in the remodelling of plasma lipoproteins: cholesteryl ester transfer protein (CETP) and phospholipid transfer protein (PLTP). CETP mediates the transfer/exchange of cholesterylesters, triglycerides and phospholipids between high-density lip

  8. Thermodynamic study on the formation of acetylene during coal pyrolysis in the arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Bao, W.; Li, F.; Cai, G.; Lu, Y.; Chang, L. [Taiyuan University of Technology, Taiyuan (China)

    2009-07-01

    Based on the principle of minimizing the Gibbs free energy, the composition of C-H-O-N-S equilibrium system about acetylene formation during the pyrolysis in arc plasma jet for four kinds of different rank-ordered coals such as Datong, Xianfeng, Yangcheng, and Luan was analyzed and calculated. The results indicated that hydrogen, as the reactive atmosphere, was beneficial to the acetylene formation. The coal ranks and the hydrogen, oxygen, nitrogen, and sulfur in coal all could obviously affect the acetylene yield. The mole fraction of acetylene is the maximum when the ratio value of atom H/C was 2. The content of oxygen was related to the acetylene yield, but it does not compete with CO formation. These agreed with the experimental results, and they could help to select the coal type for the production of acetylene through plasma pyrolysis process.

  9. INVESTIGATION OF MACHINABILITY IN Co AND Cr CONTAINING HARD MATERIALS HEATED BY PLASMA ARC

    Directory of Open Access Journals (Sweden)

    Halis Çelik

    1996-02-01

    Full Text Available Turning soft materials is not a problem in these days. But machinability of hard materials have been necessary. A lot of research has been done on machinability of difficult-to-cut materials. The aim of the present study is toinvestigate the machinability of three of hard materials after heating and softening. In this study for machining difficult-to-cut materials, different heating processes were applied and for heating, lately developed plasma heating method was used. To cut the hard material heated by plasma arc, tungsten carbide cutting tool was used. In the study, three different hard materials have been used. These were ferritic steel with 14 % Cr, Ti added cast iron, 8.5 % Cr cast steel and Co-Cr-W alloyed steel which is called stellite 6 and used in the textile industry andat power stations. In this study cutting forces, wear of cutting tool and surface roughness were investigated.

  10. Radiative heat transfer in plasma of pulsed high pressure caesium discharge

    Science.gov (United States)

    Lapshin, V. F.

    2016-01-01

    Two-temperature many component gas dynamic model is used for the analysis of features of radiative heat transfer in pulsed high pressure caesium discharge plasma. It is shown that at a sufficiently high pressure the radial optical thickness of arc column is close to unit (τR (λ) ∼ 1) in most part of spectrum. In this case radiative heat transfer has not local character. In these conditions the photons which are emitted in any point of plasma volume are absorbed in other point remote from an emission point on considerable distance. As a result, the most part of the electric energy put in the discharge mainly near its axis is almost instantly redistributed on all volume of discharge column. In such discharge radial profiles of temperature are smooth. In case of low pressure, when discharge plasma is optically transparent for own radiation in the most part of a spectrum (τR(λ) << 1), the emission of radiation without reabsorption takes place. Radiative heat transfer in plasma has local character and profiles of temperature have considerable gradient.

  11. Modification of a metallic surface in a vacuum arc discharge plasma using thermally stimulated ion diffusion

    Science.gov (United States)

    Muboyadzhyan, S. A.

    2008-12-01

    A new process for modifying a metallic surface in a vacuum arc discharge plasma using thermally stimulated ion diffusion is considered. The effect of the bias voltage (negative substrate potential) on the processes that occur on the surface of a treated part is studied when the substrate material interacts with an accelerated metallic-ion flow. The phase and elemental compositions of the modified layer are studied for substrates made of nickel-based superalloys, austenitic and martensitic steels, and titanium-based alloys. The heat resistance, the salt corrosion resistance, and the corrosion cracking resistance of steels and titanium-based alloys are investigated after their modification in vacuum arc plasmas of pure metals (Ti, Zr, Al, Cr, Y) and related alloys. The surface modification caused by the thermally stimulated ion saturation of the surfaces of parts made from structural materials is shown to change the structural-phase states of their surfaces and, correspondingly, the properties of these materials in relation to the state of the surface.

  12. Synthesis of silicon carbide from rice husk in a dc arc plasma reactor

    Energy Technology Data Exchange (ETDEWEB)

    Nayak, B.B.; Mohanty, B.C.; Singh, S.K. [Regional Research Lab., Bhubaneswar (India)

    1996-05-01

    SiC particles have been synthesized in the {alpha}-phase from a mixture of boiler-burnt rice husk and graphite powder in a dc extended arc plasma reactor on a 200--250 g scale. A SiC yield as high as 72% was achieved at a 3.03:1 carbon-to-silica ratio. 21R polytypism, which is rare to grow, was observed in the SiC. About 90% of the SiC particles produced were found to lie under 163 {micro}m, 50% under 90 {micro}m, and 10% under 28 {micro}m size. Very fine particles under 10 {micro}m size occurred to the extent of 3%. XRD and SEM characterizations were carried out to study the phase and morphology of the particles. Heterogeneous gas-phase reactions seem to be responsible for intermediate-size SiC particle growth in the multitemperature zone dc extended arc plasma reactor.

  13. Formation of Ultrananocrystalline Diamond/Amorphous Carbon Composite Films in Vacuum Using Coaxial Arc Plasma Gun

    Science.gov (United States)

    Hanada, Kenji; Yoshida, Tomohiro; Nakagawa, You; Yoshitake, Tsuyoshi

    2010-12-01

    Ultrananocrystalline diamond (UNCD)/nonhydrogenated amorphous carbon (a-C) composite films were grown in vacuum using a coaxial arc plasma gun. From the X-ray diffraction measurement, the UNCD crystallite size was estimated to be 1.6 nm. This size is dramatically reduced from that (2.3 nm) of UNCD/hydrogenated amorphous carbon (a-C:H) composite films grown in a hydrogen atmosphere. The sp3/(sp3 + sp2) value, which was estimated from the X-ray photoemission spectrum, was also reduced to be 41%. A reason for it might be the reduction in the UNCD crystallite size. From the near-edge X-ray absorption fine-structure (NEXAFS) spectrum, it was found that the π*C=C and π*C≡C bonds are preferentially formed instead of the σ*C-H bonds in the UNCD/a-C:H films. Since the extremely small UNCD crystallites (1.6 nm) correspond to the nuclei of diamond, we consider that UNCD crystallite formation should be due predominantly to nucleation. The supersaturated condition required for nucleation is expected to be realized in the deposition using the coaxial arc plasma gun.

  14. Synthesis of Nanosized Titanium Oxide and Nitride Through Vacuum Arc Plasma Expansion Technique

    Science.gov (United States)

    Lepeshev, A. A.; Karpov, I. V.; Ushakov, A. V.; Fedorov, L. Yu.; Shaihadinov, A. A.

    2016-12-01

    Physical vapor deposition techniques such vacuum arc plasma deposition — which are very commonly used in thin film technology — appear to hold much promise for the synthesis of nanocrystalline thin films as well as nanoparticles. Monodisperse and spherical titanium oxide (TiO2) and nitride nanoparticles were produced at room temperature as a cluster beam in the gas phase using a cluster-deposition source. Using the basic principles of the gas condensation method, this study has developed vacuum arc nanoparticle synthesis system. We demonstrate that major process deposition parameter is the pressure in the plasma chamber. This is the major advantage of these techniques over thermal evaporation. Our method affords TiN powders with high specific surface areas exceeding 200m2g-1. TEM micrograph of TiO2 nanoparticles prepared at an oxygen pressure of 60Pa show an average particle size of 6nm. TiO2 nanoparticles prepared at an oxygen pressure of 70Pa were observed to not have a reduced average particle size.

  15. Experimental and theoretical investigation for the suppression of the plasma arc drop in the thermionic converter

    Science.gov (United States)

    Shaw, D. T.; Manikopoulos, C. N.; Chang, T.; Lee, C. H.; Chiu, N.

    1977-01-01

    Ion generation and recombination mechanisms in the cesium plasma as they pertain to the advanced mode thermionic energy converter were studied. The decay of highly ionized cesium plasma was studied in the near afterglow to examine the recombination processes. Very low recombination in such a plasma may prove to be of considerable importance in practical converters. The approaches of external cesium generation were vibrationally excited nitrogen as an energy source of ionization of cesium ion, and microwave power as a means of resonant sustenance of the cesium plasma. Experimental data obtained so far show that all three techniques - i.e., the non-LTE high-voltage pulsing, the energy transfer from vibrationally excited diatomic gases, and the external pumping with a microwave resonant cavity - can produce plasmas with their densities significantly higher than the Richardson density. The implication of these findings as related to Lam's theory is discussed.

  16. Effect of carrier gas composition on transferred arc metal nanoparticle synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Stein, Matthias, E-mail: matthias.stein@uni-due.de; Kiesler, Dennis; Kruis, Frank Einar [University of Duisburg-Essen, Institute for Nanostructures and Technology (NST) and Center for Nanointegration Duisburg-Essen (CENIDE) (Germany)

    2013-01-15

    Metal nanoparticles are used in a great number of applications; an effective and economical production scaling-up is hence desirable. A simple and cost-effective transferred arc process is developed, which produces pure metal (Zn, Cu, and Ag) nanoparticles with high production rates, while allowing fast optimization based on energy efficiency. Different carrier gas compositions, as well as the electrode arrangements and the power input are investigated to improve the production and its efficiency and to understand the arc production behavior. The production rates are determined by a novel process monitoring method, which combines an online microbalance method with a scanning mobility particle sizer for fast production rate and size distribution measurement. Particle characterization is performed via scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction measurements. It is found that the carrier gas composition has the largest impact on the particle production rate and can increase it with orders of magnitude. This appears to be not only a result of the increased heat flux and melt temperature but also of the formation of tiny nitrogen (hydrogen) bubbles in the molten feedstock, which impacts feedstock evaporation significantly in bi-atomic gases. A production rate of sub 200 nm particles from 20 up to 2,500 mg/h has been realized for the different metals. In this production range, specific power consumptions as low as 0.08 kWh/g have been reached.

  17. Achieving High Strength Joint of Pure Copper Via Laser-Cold Metal Transfer Arc Hybrid Welding

    Science.gov (United States)

    Chen, Yulong; Chen, Cong; Gao, Ming; Zeng, Xiaoyan

    2016-06-01

    Fiber laser-cold metal transfer arc hybrid welding of pure copper was studied. Weld porosity was tested by X-ray nondestructive testing. Microstructure and fracture features were observed by scanning electron microscopy. Mechanical properties were evaluated by cross weld tensile test. Full penetrated and continuous welds were obtained by hybrid welding once the laser power reached 2 kW, while they could not be obtained by laser welding alone, even though the laser power reached 5 kW. The ultimate tensile strength (UTS), the yield strength (YS), and the elongation of the best hybrid weld material were up to 227, 201 MPa, and 21.5 pct, respectively. The joint efficiencies in UTS and YS of hybrid weld were up to 84 and 80 pct of the BM, respectively. The fracture location changes from the fusion zone to the heat-affected zone with the increase of laser power. Besides, the mechanisms of process stability and porosity suppression were clarified by laser-arc interaction and pool behavior. The strengthening mechanism was discussed by microstructure characteristics.

  18. Low pressure arc discharges with hollow cathodes and their using in plasma generators and charged particle sources

    CERN Document Server

    Vintizenko, L G; Koval, N N; Tolkachev, V S; Lopatin, I V; Shchanin, P M

    2001-01-01

    Paper presents the results of investigation into arc discharges with a hollow cathode generating 10 sup 1 sup 0 -10 sup 1 sup 2 concentration gas-discharge plasma in essential (approx 1 m sup 3) volumes at low (10 sup - sup 2 -1 Pa) pressures and up to 200 A discharge currents. One studied design of discharge systems with heated and cold cathodes their peculiar features, presented the parameters of plasma generators and of charged particle sources based on arc discharges and discussed, as well, the problems of more rational application of those systems in the processes for surface modification of solids

  19. Experimental study of gliding arc plasma channel motion: buoyancy and gas flow phenomena under normal and hypergravity conditions

    Science.gov (United States)

    Potočňáková, Lucia; Šperka, Jiří; Zikán, Petr; van Loon, Jack J. W. A.; Beckers, Job; Kudrle, Vít

    2017-04-01

    The details of plasma channel motion are investigated by frame-by-frame image analysis of high speed recording of a gliding arc. The gliding arc is operated in several noble gases at various flow rates, voltages and artificial gravity levels. Several peculiarities in evolution of individual glides are observed, described and discussed, such as accelerating motion of plasma channel or shortcutting events of various kinds. Statistics of averaged parameters are significantly different for buoyancy and gas drag dominated regimes, which is put into relation with differing flow patterns for hypergravity and high gas flow.

  20. Study of the feasibility of distributed cathodic arc as a plasma source for development of the technology for plasma separation of SNF and radioactive wastes

    Energy Technology Data Exchange (ETDEWEB)

    Amirov, R. Kh.; Vorona, N. A.; Gavrikov, A. V.; Liziakin, G. D.; Polistchook, V. P.; Samoylov, I. S.; Smirnov, V. P.; Usmanov, R. A., E-mail: ravus46@yandex.ru; Yartsev, I. M. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation)

    2015-12-15

    One of the key problems in the development of plasma separation technology is designing a plasma source which uses condensed spent nuclear fuel (SNF) or nuclear wastes as a raw material. This paper covers the experimental study of the evaporation and ionization of model materials (gadolinium, niobium oxide, and titanium oxide). For these purposes, a vacuum arc with a heated cathode on the studied material was initiated and its parameters in different regimes were studied. During the experiment, the cathode temperature, arc current, arc voltage, and plasma radiation spectra were measured, and also probe measurements were carried out. It was found that the increase in the cathode heating power leads to the decrease in the arc voltage (to 3 V). This fact makes it possible to reduce the electron energy and achieve singly ionized plasma with a high degree of ionization to fulfill one of the requirements for plasma separation of SNF. This finding is supported by the analysis of the plasma radiation spectrum and the results of the probe diagnostics.

  1. Study on main factors influencing acetylene formation during coal pyrolysis in arc plasma

    Energy Technology Data Exchange (ETDEWEB)

    Bao, W.R.; Chang, L.P.; Lu, Y.K. [Taiyuan University of Technology, Taiyuan (China)

    2006-05-15

    Acetylene from coal pyrolysis in arc plasma jet is simple and environmentally friendly with promising applications. A set of rank-ordered coal samples were selected in this study, in order to study the effects of volatile matter yield and the content of carbon, hydrogen and oxygen in raw coal on the yield of acetylene from arc plasma pyrolysis. The influence of feeding rate on the conversion of coal and acetylene yield was also investigated. The results showed that acetylene and carbon monoxide were the main gaseous products during coal pyrolysis under plasma conditions. A higher acetylene yield of 17-22% could be obtained from coal with volatile matter yield of 25-40%. A high C/H mole ratio and low O/C mole ratio were favorable to the formation of acetylene. The percent conversion of coal, the yield of acetylene and the specific energy consumption (SEC) decreased as the feeding rate increased, but the trends in their changes were not identical. The relative volume fractions (RVF) in gaseous products of acetylene and carbon monoxide increased with increasing coal feeding rate until 5 g s{sup -1}, while the RVFs of light hydrocarbons such as CH{sub 4}, C{sub 2}H{sub 4} and C{sub 3}H{sub 6} gradually increased. The change in the selectivity for acetylene was not obvious when the feeding rate was less than 4 g s{sup -1}. However, the portion of acetylene in the total gaseous products decreased rapidly when the coal feeding rate was further increased.

  2. Generation of high charge state metal ion beams by electron cyclotron resonance heating of vacuum arc plasma in cusp trap.

    Science.gov (United States)

    Nikolaev, A G; Savkin, K P; Oks, E M; Vizir, A V; Yushkov, G Yu; Vodopyanov, A V; Izotov, I V; Mansfeld, D A

    2012-02-01

    A method for generating high charge state heavy metal ion beams based on high power microwave heating of vacuum arc plasma confined in a magnetic trap under electron cyclotron resonance conditions has been developed. A feature of the work described here is the use of a cusp magnetic field with inherent "minimum-B" structure as the confinement geometry, as opposed to a simple mirror device as we have reported on previously. The cusp configuration has been successfully used for microwave heating of gas discharge plasma and extraction from the plasma of highly charged, high current, gaseous ion beams. Now we use the trap for heavy metal ion beam generation. Two different approaches were used for injecting the vacuum arc metal plasma into the trap--axial injection from a miniature arc source located on-axis near the microwave window, and radial injection from sources mounted radially at the midplane of the trap. Here, we describe preliminary results of heating vacuum arc plasma in a cusp magnetic trap by pulsed (400 μs) high power (up to 100 kW) microwave radiation at 37.5 GHz for the generation of highly charged heavy metal ion beams.

  3. A Desorbed Gas Molecular Ionization Mechanism for Arcing Onset in Solar Arrays Immersed in a Low-Density Plasma

    Science.gov (United States)

    Galofaro, J.; Vayner, B.; Ferguson, D.; Degroot, W.

    2002-01-01

    Previous experimental studies have hypothesized that the onset of Solar Array Arc (SAA) initiation in low-density space plasmas is caused by a desorbed gas molecular ionization mechanism. Indeed past investigations performed at the NASA Glenn Plasma Interaction Facility tend to not only support the desorbed gas molecular ionization mechanism, but have gone as far as identifying the crucial molecular species that must be present for molecular ion dominated process to occur. When electrical breakdown occurs at a triple junction site on a solar array panel, a quasi-neutral plasma cloud is ejected. Assuming the main component of the expelled plasma cloud by weight is due to water vapor, the fastest process available is due to HO molecules and OH(+) ions, or more succinctly, dissociative molecular-ion dominated recombination processes: H2O(+) + e(-) yields H* + OH*. Recently published spectroscopic observations of solar array arc spectra in ground tests have revealed the well-known molecular OH band (302 to 309nm), as well as the molecular SiH band (387nm peak), and the molecular CH band (432nm peak). Note that the OH band is observed in emission arcs where water vapor is present. Strong atomic lines were also observed for H(sub beta) at 486nm and H(sub alpha) at 656.3nm in prior ground testing. Independent supporting evidence of desorbed gas molecular ionization mechanisms also come from measurements of arc current pulse widths at different capacitances. We will revisit an earlier first order approximation demonstrating the dependence of arc current pulse widths on the square root of the capacitance. The simple arc current pulse width model will be then be used to estimate the temperature of the arc plasma (currently believed to be somewhere in the range of 3 to 5 eV). The current paper then seeks to extend the outlined work by including numerous vacuum chamber measurements obtained with a quadrupole mass spectrometer. A small solar array was mounted inside the vacuum

  4. Comparison of Two Models for Radiative Heat Transfer in High Temperature Thermal Plasmas

    Directory of Open Access Journals (Sweden)

    Matthieu Melot

    2011-01-01

    Full Text Available Numerical simulation of the arc-flow interaction in high-voltage circuit breakers requires a radiation model capable of handling high-temperature participating thermal plasmas. The modeling of the radiative transfer plays a critical role in the overall accuracy of such CFD simulations. As a result of the increase of computational power, CPU intensive methods based on the radiative transfer equation, leading to more accurate results, are now becoming attractive alternatives to current approximate models. In this paper, the predictive capabilities of the finite volume method (RTE-FVM and the P1 model are investigated. A systematic comparison between these two models and analytical solutions are presented for a variety of relevant test cases. Two implementations of each approach are compared, and a critical evaluation is presented.

  5. Synthesis and characteristics of Ag/Pt bimetallic nanocomposites by arc-discharge solution plasma processing.

    Science.gov (United States)

    Pootawang, Panuphong; Saito, Nagahiro; Takai, Osamu; Lee, Sang-Yul

    2012-10-05

    Arc discharge in solution, generated by applying a high voltage of unipolar pulsed dc to electrodes of Ag and Pt, was used as a method to form Ag/Pt bimetallic nanocomposites via electrode erosion by the effects of the electric arc at the cathode (Ag rod) and the sputtering at the anode (Pt rod). Ag/Pt bimetallic nanocomposites were formed as colloidal particles dispersed in solution via the reduction of hydrogen radicals generated during discharge without the addition of chemical precursor or reducing agent. At a discharge time of 30 s, the fine bimetallic nanoparticles with a mean particle size of approximately 5 nm were observed by transmission electron microscopy (TEM). With increasing discharge time, the bimetallic nanoparticle size tended to increase by forming an agglomeration. The presence of the relatively small amount of Pt dispersed in the Ag matrix could be observed by the analytical mapping mode of energy-dispersive x-ray spectroscopy and high-resolution TEM. This demonstrated that the synthesized particle was in the form of a nanocomposite. No contamination of other chemical substances was detected by x-ray photoelectron spectroscopy. Hence, solution plasma could be a clean and simple process to effectively synthesize Ag/Pt bimetallic nanocomposites and it is expected to be widely applicable in the preparation of several types of nanoparticle.

  6. Highly zone-dependent synthesis of different carbon nanostructures using plasma-enhanced arc discharge technique

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Rajesh, E-mail: rajeshbhu1@gmail.com [Yonsei University, Department of Materials Science & Engineering (Korea, Republic of); Singh, Rajesh Kumar, E-mail: rksbhu@gmail.com [Banaras Hindu University, Department of Applied Physics, Indian Institute of Technology (India); Dubey, Pawan Kumar [University of Allahabad, Nanotechnology Application Centre (India); Yadav, Ram Manohar [Rice University, Department of Materials Science and Nano Engineering (United States); Singh, Dinesh Pratap [Universidad de Santiago de Chile, Departamento de Física (Chile); Tiwari, R. S.; Srivastava, O. N. [Banaras Hindu University, Department of Physics (India)

    2015-01-15

    Three kinds of carbon nanostructures, i.e., graphene nanoflakes (GNFs), multi walled carbon nanotubes (MWCNTs), and spherical carbon nanoparticles (SCNPs) were comparatively investigated in one run experiment. These carbon nanostructures are located at specific location inside the direct current plasma-assisted arc discharge chamber. These carbon nanomaterials have been successfully synthesized using graphite as arcing electrodes at 400 torr in helium (He) atmosphere. The SCNPs were found in the deposits formed on the cathode holder, in which highly curled graphitic structure are found in majority. The diameter varies from 20 to 60 nm and it also appears that these particles are self-assembled to each other. The MWCNTs with the diameter of 10–30 nm were obtained which were present inside the swelling portion of cathode deposited. These MWCNTs have 14–18 graphitic layers with 3.59 Å interlayer spacing. The GNFs have average lateral sizes of 1–5 μm and few of them are stacked layers and shows crumpled like structure. The GNFs are more stable at low temperature (low mass loss) but SCNPs have low mass loss at high temperature.

  7. The influence of arc plasma electric and laser treatment on the structure and properties of the high speed steel

    Directory of Open Access Journals (Sweden)

    W. Bochnowski

    2009-07-01

    Full Text Available The examination of the structure, hardness and abrasion resistance of surface layer of high speed steel: HS 2-10-1-8, HS 6-5-2 and HS 10-2-5-8 after arc plasma and laser welding are presented in the paper. They are compared with the properties obtained after conventional hardening. Diode laser of continuous operation and GTAW (Gas Tungsten Arc Welding method were used. As a result of concentrated energy beam treatment applied to a steels surface layer, the structures characteristic of rapid solidification / crystallization process were obtained. The treatment of the steel by arc plasma electric with a single remelted track about 7 mm width does not lead to growth of the mechanical and tribological properties of high speed steels. The growth of microhardness as well as low the coefficient Archard of the high speed steel after remelting on the surface single track about 6 mm width by diode laser using can be obtained.

  8. Preparation and Characterization of NiO Nanoparticles by Anodic Arc Plasma Method

    Directory of Open Access Journals (Sweden)

    Hongxia Qiao

    2009-01-01

    Full Text Available NiO nanoparticles with average particle size of 25 nm were successfully prepared by anodic arc plasma method. The composition, morphology, crystal microstructure, specific surface area, infrared spectra, and particle size distribution of product were analyzed by using X-ray diffraction (XRD, transmission electron microscopy (TEM and the corresponding selected area electron diffraction (SAED, Fourier transform infrared (FTIR spectrum, and Brunauer-Emmett-Teller (BET N2 adsorption. The experiment results show that the NiO nanoparticles are bcc structure with spherical shape and well dispersed, the particle size distribution ranging from 15 to 45 nm with the average particle size is about 25 nm, and the specific surface area is 33 m2/g. The infrared absorption band of NiO nanoparticles shows blue shifts compared with that of bulk NiO.

  9. Steam Reforming of Dimethyl Ether by Gliding Arc Gas Discharge Plasma for Hydrogen Production

    Institute of Scientific and Technical Information of China (English)

    王保伟; 孙启梅; 吕一军; 杨美琳; 闫文娟

    2014-01-01

    Gliding arc gas discharge plasma was used for the generation of hydrogen from steam reforming of di-methyl ether (DME). A systemic procedure was employed to determine the suitable experimental conditions. It was found that DME conversion first increased up to the maximum and then decreased slightly with the increase of added water and air. The increase of total feed gas flow rate resulted in the decrease of DME conversion and hy-drogen yield, but hydrogen energy consumption dropped down to the lowest as total feed gas flow rate increased to 76 ml·min-1. Larger electrode gap and higher discharge voltage were advantageous. Electrode shape had an impor-tant effect on the conversion of DME and production of H2. Among the five electrodes, electrode 2# with valid length of 55 mm and the radian of 34 degrees of the top electrode section was the best option, which enhanced ob-viously the conversion of DME.

  10. Wear Resistance of Deposited Layer Using Nickel-Based Composite Powders by Plasma-Arc Surfacing

    Institute of Scientific and Technical Information of China (English)

    DONG Li-hong; ZHU Sheng; XU Bin-shi; DU Ze-yu

    2004-01-01

    Nickel-based composite alloy powders were deposited on the surface of Q235 steel by plasma-arc surfacing in this work. Optimal proportions of elements intensifying the composite powders were ascertained by orthogonal design of three factors and three levels and orthogonal polynomial regression analysis , which Cr , Mn , W were 10% ,4% and 7 % respectively.Phase and structure of deposited materials were characterized by optical microscope and X- ray diffraction. Hardness tests and wear resistance tests were carried out to determine the performance of the deposited layers. The results show that the microstructure of deposited layers of composite powders mainly consist of γ-( Ni, Fe ) , γ- Ni, WC, W2 C, Mn31Si12, Cr23 C6,Cr7 C3, Cr, NiB, Ni2B etc. Wear resistance and hardness of the surface increased evidently.

  11. Deposition of titanium nitride layers by electric arc - Reactive plasma spraying method

    Energy Technology Data Exchange (ETDEWEB)

    Serban, Viorel-Aurel [University ' Politehnica' of Timisoara, Faculty of Mechanical Engineering, No. 1 Mihai Viteazu Boulevard, 300222 Timisoara (Romania); Rosu, Radu Alexandru, E-mail: raduniz@gmail.com [University ' Politehnica' of Timisoara, Faculty of Mechanical Engineering, No. 1 Mihai Viteazu Boulevard, 300222 Timisoara (Romania); Bucur, Alexandra Ioana [National Institute for Research and Development in Electrochemistry and Condensed Matter Timisoara, Analysis and Characterization Department, No. 1 P Andronescu Street, Timisoara 300224 (Romania); Pascu, Doru Romulus [Romania National Research and Development Institute for Welding and Material Testing Timisoara, No. 30 Mihai Viteazu Boulevard, 300222 Timisoara (Romania)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer Titanium nitride layers deposited by electric arc - reactive plasma spraying method. Black-Right-Pointing-Pointer Deposition of titanium nitride layers on C45 steel at different spraying distances. Black-Right-Pointing-Pointer Characterization of the coatings hardness as function of the spraying distances. Black-Right-Pointing-Pointer Determination of the corrosion behavior of titanium nitride layers obtained. - Abstract: Titanium nitride (TiN) is a ceramic material which possesses high mechanical properties, being often used in order to cover cutting tools, thus increasing their lifetime, and also for covering components which are working in corrosive environments. The paper presents the experimental results on deposition of titanium nitride coatings by a new combined method (reactive plasma spraying and electric arc thermal spraying). In this way the advantages of each method in part are combined, obtaining improved quality coatings in the same time achieving high productivity. Commercially pure titanium wire and C45 steel as substrate were used for experiments. X-ray diffraction analysis shows that the deposited coatings are composed of titanium nitride (TiN, Ti{sub 2}N) and small amounts of Ti{sub 3}O. The microstructure of the deposited layers, investigated both by optical and scanning electron microscopy, shows that the coatings are dense, compact, without cracks and with low porosity. Vickers microhardness of the coatings presents maximum values of 912 HV0.1. The corrosion tests in 3%NaCl solution show that the deposited layers have a high corrosion resistance compared to unalloyed steel substrate.

  12. The formation mechanism of CO2 and its conversion in the process of coal gasification under arc plasma conditions

    Science.gov (United States)

    He, Xiaojun; Zheng, Mingdong; Qiu, Jieshan; Zhao, Zongbin; Ma, Tengcai

    2006-05-01

    The carbon dioxide (CO2) formation mechanism and co-conversion of CO2 with coal was investigated in the process of coal gasification in a steam medium at atmospheric pressure under arc plasma conditions in a tube-type setup. The arc plasma was diagnosed in situ by optical emission spectroscopy and the gas products were analysed by gas chromatography. CO2 yields are correlated with the quantitative emission peak intensity of the active species in plasma when the operating parameter is changed. The results show that the greater the emission peak intensity of the CH radicals, C2 radicals, OH radicals or O atoms, the smaller the CO2 yield is, which means that the CO2 formation process is inhibited by increasing the concentration of the mentioned active species under arc plasma conditions. On the basis of the diagnosis results, co-conversion of CO2 and coal in a steam medium under plasma conditions was carried out in the same setup and the results show that CO2 conversion reaches 88.6% while the concentration of CO + H2 reaches 87.4%; at the same time, coal conversion is in the range 54.7-68.7%, which proves that co-conversion of CO2 and coal in a steam medium under plasma conditions might be a prospective way to utilize CO2 and the production of synthesis gas.

  13. New approaches for the reduction of plasma arc drop in second-generation thermionic converters

    Science.gov (United States)

    Hatziprokopiou, M. E.; Shaw, D. T.

    1981-03-01

    Investigations of ion generation and recombination mechanisms in the cesium plasma are described with respect to the advanced mode thermionic energy converter. The changes in plasma density and temperature within the converter were studied under the influence of several promising auxiliary ionization candidate sources. Three novel approaches of external cesium ion generation were studied in some detail, namely vibrationally excited N2 as an energy source of ionization of Cs ions in a dc discharge, microwave power as a means of resonant sustenance of the cesium plasma, and ion generation in a pulse N2-Cs mixture. The data obtained show that all three techniques - i.e., the non-LTE high voltage pulsing, the energy transfer from vibrationally excited diatomic gases, and the external pumping with a microwave power have considerable promise as schemes in auxiliary ion generation applicable to the advanced thermionic energy converter.

  14. Integrated parametric study of a hybrid-stabilized argon-water arc under subsonic, transonic and supersonic plasma flow regimes

    Science.gov (United States)

    Jeništa, J.; Takana, H.; Nishiyama, H.; Bartlová, M.; Aubrecht, V.; Křenek, P.; Hrabovský, M.; Kavka, T.; Sember, V.; Mašláni, A.

    2011-11-01

    This paper presents a numerical investigation of characteristics and processes in the worldwide unique type of thermal plasma generator with combined stabilization of arc by argon flow and water vortex, the so-called hybrid-stabilized arc. The arc has been used for spraying of ceramic or metallic particles and for pyrolysis of biomass. The net emission coefficients as well as the partial characteristics methods for radiation losses from the argon-water arc are employed. Calculations for 300-600 A with 22.5-40 standard litres per minute (slm) of argon reveal transition from a transonic plasma flow for 400 A to a supersonic one for 600 A with a maximum Mach number of 1.6 near the exit nozzle of the plasma torch. A comparison with available experimental data near the exit nozzle shows very good agreement for the radial temperature profiles. Radial velocity profiles calculated 2 mm downstream of the nozzle exit show good agreement with the profiles determined from the combination of calculation and experiment (the so-called integrated approach). A recent evaluation of the Mach number from the experimental data for 500 and 600 A confirmed the existence of the supersonic flow regime.

  15. The influence of the arc plasma treatment on the structure and microhardness 100Cr6 bearing steel

    Directory of Open Access Journals (Sweden)

    W. Bochnowski

    2010-04-01

    Full Text Available The effect of arc plasma treatment on structure and microhardness of 100Cr6 steel was investigated. Four different the current intensity has been used to remelting surface of the steel. SEM and LM microscopes have been used to evaluate microstructure of remelted zone (RZ. In the remelting zone (RZ were obtained characteristic for rapid crystallization process the dendritic cell structure. Inside the dendritic cells in dependency to current intensity of arc, the martensite or bainite and retained austenite was observed. On the boundaries of the dendritic cells as a result of segregation of C and Cr the alloyed cementite is formed. The cooling rate of the remelted zone is higher than the cooling rate obtained in the classical heat treatment. The maximum hardness 840 HV0,1 was measured in material after treatment with a smaller current intensity of arc plasma – 60A. Increases of the current intensity of arc plasma from 60 A to 110 A (for fixed speed rate of source lead to increases the depth of the remelted zone from 1,5 to 2,3 mm.

  16. Gliding arc plasma assisted N2O dissociation for monopropellant propulsion

    Science.gov (United States)

    Bosi, Franco J.; Dobrynin, Danil

    2017-01-01

    In this paper we address the capability of gliding arc (GA) discharges to promote plasma assisted combustion of nitrous oxide gas (N2O) for spacecraft monopropellant thruster applications. N2O is a ‘green’ propellant with interesting properties, but highly inert when used as monopropellant. Higher vibrational temperatures {{T}\\text{v}}>T , and hot spot localized dissociation, achieved within the GA reactor, are able to promote combustion of the gas. The vibrational temperature of the N2 second positive system is estimated by means of optical emission spectroscopy and reaches 5000 K, while the gas temperature reaches 1500 K the degree of N2O decomposition, estimated by FTIR measurements, ranged from 25 to 85%. A kinetic model for N2O dissociation is developed; the model shows that simply heating the gas in the same conditions is not enough to produce appreciable dissociation, providing further evidence of the catalytic action of the plasma. Results allow us to predict the propulsive efficiencies to be about 43%, with a thrust level of 37 mN; this result compares positively with the existing N2O resistojet technology.

  17. Mass transfer and trace element redistribution during hydration of granulites in the Bergen Arcs, Norway

    Science.gov (United States)

    Centrella, Stephen; Austrheim, Håkon; Putnis, Andrew

    2016-10-01

    The Bergen Arcs, located on the western coast of Norway, are characterized by Precambrian granulite facies rocks partially hydrated at amphibolite and eclogite facies conditions. At Hilland Radöy, granulite displays sharp hydration fronts across which the granulite facies assemblage composed of garnet (55%) and clinopyroxene (45%) is replaced by an amphibolite facies mineralogy defined by chlorite, epidote, and amphibole. The replacement of both phases is pseudomorphic and the overall reaction is isovolumetric. In the present study, LA ICPMS has been used to determine the trace element redistribution during the hydration. Although the bulk concentrations of the trace elements do not change, the LILE, HFSE, and REE losses and gains in replacing the garnet are qualitatively balanced by the opposite gains and losses associated with the replacement of clinopyroxene. From the REE compositions of the parent granulite and the product amphibolite, measured in μg/cm3, we conclude that the mass of rock lost to the fluid phase during the hydration is approximately 20%. This suggests a mechanism for coupling between the local stress generated by hydration reactions and mass transfer, dependent on the spatial scale over which the system is open.

  18. Mechanism of coal gasification in a steam medium under arc plasma conditions

    Science.gov (United States)

    He, Xiaojun; Ma, Tengcai; Qiu, Jieshan; Sun, Tianjun; Zhao, Zongbin; Zhou, Ying; Zhang, Jialiang

    2004-08-01

    The coal gasification mechanism in a steam medium under arc plasma conditions was investigated at atmospheric pressure in a tube-type setup. The gases obtained were analysed by gas chromatography. The active species in the plasma were monitored and analysed in situ by optical emission spectroscopy (OES). The effects of operating parameters such as the current in the electromagnetic coil and the flow rate of carrier gas (air) on the gas yields as well as on the emission intensities of the active species were studied. The quantitative emission intensities of the active species are correlated with the yields of main components in the gas products. The results show that as the current in the electromagnetic coil increases, the yields of H2, CO, CO2 and O2 as well as the peak intensities of C atom, H atom, CH radical and CO+ ion detected by OES pass through a maximum. It is also found that as the flow rate of carrier gas (air) increases, the yields of CO, CO2 and O2 increase; at the same time, the yield of H2 and the peak intensities of C atoms, H atoms, CH radicals and OH radicals decrease. The presence of C atoms or H atoms in the reaction system favours the formation of H2, which is evidenced by the fact that the yield of H2 increases as the optical emission intensity of C atom or H atom species increases. Based on the experimental results, a possible mechanism of coal gasification in steam medium under plasma conditions is proposed and discussed.

  19. Mechanism of coal gasification in a steam medium under arc plasma conditions

    Energy Technology Data Exchange (ETDEWEB)

    He, X.J.; Ma, T.C.; Qiu, J.S.; Sun, T.J.; Zhao, Z.B.; Zhou, Y.; Zhang, J.L. [Dalian University of Technology, Dalian (China). Carbon Research Laboratory, Center for Nano Materials and Science

    2004-08-01

    The coal gasification mechanism in a steam medium under arc plasma conditions was investigated at atmospheric pressure in a tube-type setup. The gases obtained were analysed by gas chromatography. The active species in the plasma were monitored and analysed in situ by optical emission spectroscopy (OES). The effects of operating parameters such as the current in the electromagnetic coil and the flow rate of carrier gas (air) on the gas yields as well as on the emission intensities of the active species were studied. The quantitative emission intensities of the active species are correlated with the yields of main components in the gas products. The results show that as the current in the electromagnetic coil increases, the yields of H{sub 2}, CO, CO{sub 2} and O{sub 2} as well as the peak intensities of C atom, H atom, CH radical and CO{sup +} ion detected by OES pass through a maximum. It is also found that as the flow rate of carrier gas (air) increases, the yields of CO, CO{sub 2} and O{sub 2} increase; at the same time, the yield of H{sub 2} and the peak intensities of C atoms, H atoms, CH radicals and OH radicals decrease. The presence of C atoms or H atoms in the reaction system favours the formation of H{sub 2}, which is evidenced by the fact that the yield of H{sub 2} increases as the optical emission intensity of C atom or H atom species increases. Based on the experimental results, a possible mechanism of coal gasification in steam medium under plasma conditions is proposed and discussed.

  20. PREFACE: 1st International Symposium on Electrical Arc and Thermal Plasmas in Africa (ISAPA)

    Science.gov (United States)

    Andre, Pascal; Koalaga, Zacharie

    2012-02-01

    Logos of the University of Ouagadougou, ISAPA and Universite Blaise Pascal Africa (especially Sub-Saharan Africa) is a continent where electrification is at a low level. However, the development of the electrical power sector is a prerequisite for the growth of other industrial activities, that is to say for the social and economic development of African countries. Consequently, a large number of electrification projects (rural electrification, interconnection of different country's grids) takes place in many countries. These projects need expertise and make Africa a continent of opportunity for companies in different domains for business and research: energy; energetic production, transmission, distribution and protection of electricity; the supply of cable; the construction, engineering and expertise in the field of solar and wind power. The first International Symposium on electrical Arc and thermal Plasma in Africa (ISAPA) was held for the first time in Ouagadougou, Burkina Faso to progress and develop the research of new physical developments, technical breakthroughs, and ideas in the fields of electrical production and electrical applications. The ISAPA aims to encourage the advancement of the science and applications of electrical power transformation in Africa by bringing together specialists from many areas in Africa and the rest of the world. Such considerations have led us to define a Scientific Committee including representatives from many countries. This first meeting was an innovative opportunity for researchers and engineers from academic and industrial sectors to exchange views and knowledge. Both fundamental aspects such as thermal plasma, electrical arc, diagnostics and applied aspects as circuit breakers, ICP analyses, photovoltaic energy conversion and alternative energies, as well as space applications were covered. The Laboratory of Material and Environment (LAME) from Ouagadougou University and the Laboratory of Electric Arc and Thermal

  1. Simulation of Low-Voltage Arc Plasma During Contact Opening Progress

    Institute of Scientific and Technical Information of China (English)

    WU Yi; RONG Ming-zhe; SUN Zhi-qiang; WANG Xiao-hua; LI Jian; WANG Jian-hua

    2007-01-01

    This paper focuses on the simulation of the low-voltage arc with an opening contact.A controllable experiment setup with a rotating contact is designed to investigate the arc behaviour.Supported by the experiment,the phenomena of arc elongation and commutation in the case of rotating contact are simulated with the dynamic grid technique introduced.Under the given condition of the external magnetic field and the contact rotating velocity,the stagnation and rapid jump of two arc roots are observed by the calculated and experimental arc root displacement.The voltage of arc column can be divided into four phases and its sharp rising progress comes from the increase of the displacement difference between two arc roots in x direction.

  2. 3-D electrical resistivity structure based on geomagnetic transfer functions exploring the features of arc magmatism beneath Kyushu, Southwest Japan Arc

    Science.gov (United States)

    Hata, Maki; Uyeshima, Makoto; Handa, Shun; Shimoizumi, Masashi; Tanaka, Yoshikazu; Hashimoto, Takeshi; Kagiyama, Tsuneomi; Utada, Hisashi; Munekane, Hiroshi; Ichiki, Masahiro; Fuji-ta, Kiyoshi

    2017-01-01

    Our 3-D electrical resistivity model clearly detects particular subsurface features for magmatism associated with subduction of the Philippine Sea Plate (PSP) in three regions: a southern and a northern volcanic region, and a nonvolcanic region on the island of Kyushu. We apply 3-D inversion analyses for geomagnetic transfer function data of a short-period band, in combination with results of a previous 3-D model that was determined by using Network-Magnetotelluric response function data of a longer-period band as an initial model in the present inversion to improve resolution at shallow depths; specifically, a two-stage inversion is used instead of a joint inversion. In contrast to the previous model, the presented model clearly reveals a conductive block on the back-arc side of Kirishima volcano at shallow depths of 50 km; the block is associated with hydrothermal fluids and hydrothermal alteration zones related to the formation of epithermal gold deposits. A second feature revealed by the model is another conductive block regarded as upwelling fluids, extending from the upper surface of the PSP in the mantle under Kirishima volcano in the southern volcanic region. Third, a resistive crustal layer, which confines the conductive block in the mantle, is distributed beneath the nonvolcanic region. Fourth, our model reveals a significant resistive block, which extends below the continental Moho at the fore-arc side of the volcanic front and extends into the nonvolcanic region in central Kyushu.

  3. Simultaneous observation of keyhole and weld pool in plasma arc welding with a single cost-effective sensor

    Institute of Scientific and Technical Information of China (English)

    张国凯; 武传松; 刘新锋; 张晨

    2014-01-01

    The dynamic behaviors ofthe keyhole and weld pool are coupled together in plasma arc welding,and the geometric variations ofboth the keyhole and the weld pool determine the weld quality.It is ofgreat significance to simultaneously sense and monitor the keyhole and the weld pool behaviors by using a single low-cost vision sensor in plasma arc welding process.In this study,the keyhole and weld pool were observed and measured under different levels ofwelding current by using the near infrared sensing technology and the charge coupled device (CCD)sensing system.The shapes and relative position ofweld pool and keyhole under different conditions were compared and analyzed.The observation results lay solid foundation for controlling weld quality and understanding the underlying process mechanisms.

  4. Modeling of an electric arc transferred on a melted glass bath; Modelisation d`un arc electrique transfere sur un bain de verre

    Energy Technology Data Exchange (ETDEWEB)

    Mehlman, G.; Langlois, A. [SGN, 78 - Saint Quentin en Yvelines (France)

    1997-12-31

    The aim of this study is to propose a methodology allowing the simulation of melting processes involving electromagnetic phenomena. This methodology is based on the use of scientific calculation tools currently used elsewhere. The case considered in this study has been defined in collaboration with Electricite de France (EdF) and concerns more particularly an electric arc vitrification process for wastes. Basic data have been determined in order to obtain results representative of the tests performed by EdF with pilot installations. (J.S.)

  5. Unified model to the Tungsten inert Gas welding process including the cathode, the plasma and the anode; Modele couple cathode-plasma-piece en vue de la simulation du procede de soudage a l'arc TIG

    Energy Technology Data Exchange (ETDEWEB)

    Brochard, M.

    2009-06-15

    During this work, a 2D axially symmetric model of a TIG arc welding process had been developed in order to predict for given welding parameters, the needed variables for a designer of welded assembly: the heat input on the work piece, the weld pool geometry,... The developed model, using the Cast3M finite elements software, deals with the physical phenomena acting in each part of the process: the cathode, the plasma, the work piece with a weld pool, and the interfaces between these parts. To solve this model, the thermohydraulics equations are coupled with the electromagnetic equations that are calculated in part using the least squares finite element method. The beginning of the model validation consisted in comparing the results obtained with the ones available in the scientific literature. Thus, this step points out the action of each force in the weld pool, the contribution of each heat flux in the energy balance. Finally, to validate the model predictiveness, experimental and numerical sensitivity analyses were conducted using a design of experiments approach. The effects of the process current, the arc gap and the electrode tip angle on the weld pool geometry and the energy transferred to the work piece and the arc efficiency were studied. The good agreement obtained by the developed model for these outputs shows the good reproduction of the process physics. (author)

  6. Enhanced human bone marrow mesenchymal stem cell functions on cathodic arc plasma-treated titanium

    Directory of Open Access Journals (Sweden)

    Zhu W

    2015-12-01

    Full Text Available Wei Zhu,1 George Teel,1 Christopher M O’Brien,1 Taisen Zhuang,1 Michael Keidar,1 Lijie Grace Zhang1–3 1Department of Mechanical and Aerospace Engineering, 2Department of Biomedical Engineering, 3Department of Medicine, The George Washington University, Washington, DC, USA Abstract: Surface modification of titanium for use in orthopedics has been explored for years; however, an ideal method of integrating titanium with native bone is still required to this day. Since human bone cells directly interact with nanostructured extracellular matrices, one of the most promising methods of improving titanium’s osseointegration involves inducing biomimetic nanotopography to enhance cell–implant interaction. In this regard, we explored an approach to functionalize the surface of titanium by depositing a thin film of textured titanium nanoparticles via a cathodic arc discharge plasma. The aim is to improve human bone marrow mesenchymal stem cell (MSC attachment and differentiation and to reduce deleterious effects of more complex surface modification methods. Surface functionalization was analyzed by scanning electron microscopy, atomic force microscopy, contact angle testing, and specific protein adsorption. Scanning electron microscopy and atomic force microscopy examination demonstrate the deposition of titanium nanoparticles and the surface roughness change after coating. The specific fibronectin adsorption was enhanced on the modified titanium surface that associates with the improved hydrophilicity. MSC adhesion and proliferation were significantly promoted on the nanocoated surface. More importantly, compared to bare titanium, greater production of total protein, deposition of calcium mineral, and synthesis of alkaline phosphatase were observed from MSCs on nanocoated titanium after 21 days. The method described herein presents a promising alternative method for inducing more cell favorable nanosurface for improved orthopedic applications

  7. Cathodoluminescence of Cr-doped diamond-like carbon film by filtered cathodic vacuum arc plasma

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Meng-Wen; Jao, Jui-Yun [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 402, Taiwan (China); Lin, Chun-Chun; Hsieh, Wei-Jen; Yang, Yu-Hsiang [Department of Materials Science and Engineering, National Tsing Hua University, 101, Sec. 2, Kuang-Fu Road, Hsinchu 300, Taiwan (China); Cheng, Li-Shin; Shieu, F.S. [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 402, Taiwan (China); Shih, Han C., E-mail: hcshih@mx.nthu.edu.tw [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 402, Taiwan (China); Department of Materials Science and Engineering, National Tsing Hua University, 101, Sec. 2, Kuang-Fu Road, Hsinchu 300, Taiwan (China); Institute of Materials Science and Nanotechnology, Chinese Culture University, 55 Hwa Kang Road, Yang Ming Shan, Taipei 111, Taiwan (China)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer The formation of the DLC:Cr films dependent on the flow rates of C{sub 2}H{sub 2}/Ar have been achieved in our FCVA plasma. Black-Right-Pointing-Pointer The amorphous DLC:Cr have high sp{sup 2} content can be completely converted to nanocrystalline Cr{sub 3}C{sub 2}. Black-Right-Pointing-Pointer The effect of doping with Cr is apparently to change the band structure of the DLC and its consequent cathodoluminescence property. - Abstract: Cr doped diamond-like carbon (DLC:Cr) film was synthesized in various flow rates of C{sub 2}H{sub 2}/Ar under a substrate voltage of -50 V at 500 Degree-Sign C by a filtered cathodic vacuum arc plasma. This work has found that the structure of the films was correlated to the flow rate of C{sub 2}H{sub 2}/Ar but the luminescence properties are similar. The cathodoluminescence spectra of DLC:Cr films obtained at 1.9-2.4 eV verifies that the luminescence from the films is in the visible region. The incorporation of Cr into the carbon network results in red emission shifted to 1.99 eV and the orange emission (2.03 eV) also appeared due to the transitions between chromium-related electron levels and {sigma}* states. The peak at 2.10 eV may result from the defects of the structures in DLC:Cr films.

  8. Microstructural Evolution and Mechanical Properties of Inconel 625 Alloy during Pulsed Plasma Arc Deposition Process

    Institute of Scientific and Technical Information of China (English)

    Fujia Xu; Yaohui Lv; Yuxin Liu; Fengyuan Shu; Peng He; Binshi Xu

    2013-01-01

    Pulsed plasma arc deposition (PPAD),which combines pulsed plasma cladding with rapid prototyping,is a promising technology for manufacturing near net shape components due to its superiority in cost and convenience of processing.In the present research,PPAD was successfully used to fabricate the Ni-based superalloy Inconel 625 components.The microstructures and mechanical properties of deposits were investigated by scanning electron microscopy (SEM),optical microscopy (OM),transmission electron microscopy (TEM) with energy dispersive spectrometer (EDS),microhardness and tensile testers.It was found that the as-deposited structure exhibited homogenous columnar dendrite structure,which grew epitaxially along the deposition direction.Moreover,some intermetallic phases such as Laves phase,minor MC (NbC,TiC) carbides and needle-like δ-Ni3Nb were observed in γ-Ni matrix.Precipitation mechanism and distribution characteristics of these intermetallic phases in the as-deposited 625 alloy sample were analyzed.In order to evaluate the mechanical properties of the deposits,microhardness was measured at various location (including transverse plane and longitudinal plane).The results revealed hardness was in the range of 260-285 HVo.2.In particular,microhardness at the interface region between two adjacent deposited layers was slightly higher than that at other regions due to highly refined structure and the disperse distribution of Laves particles.Finally,the influence of precipitation phases and fabrication strategies on the tensile properties of the as-deposited samples was investigated.The failure modes of the tensile specimens were analyzed with fractography.

  9. Deposition of titanium nitride layers by electric arc - Reactive plasma spraying method

    Science.gov (United States)

    Şerban, Viorel-Aurel; Roşu, Radu Alexandru; Bucur, Alexandra Ioana; Pascu, Doru Romulus

    2013-01-01

    Titanium nitride (TiN) is a ceramic material which possesses high mechanical properties, being often used in order to cover cutting tools, thus increasing their lifetime, and also for covering components which are working in corrosive environments. The paper presents the experimental results on deposition of titanium nitride coatings by a new combined method (reactive plasma spraying and electric arc thermal spraying). In this way the advantages of each method in part are combined, obtaining improved quality coatings in the same time achieving high productivity. Commercially pure titanium wire and C45 steel as substrate were used for experiments. X-ray diffraction analysis shows that the deposited coatings are composed of titanium nitride (TiN, Ti2N) and small amounts of Ti3O. The microstructure of the deposited layers, investigated both by optical and scanning electron microscopy, shows that the coatings are dense, compact, without cracks and with low porosity. Vickers microhardness of the coatings presents maximum values of 912 HV0.1. The corrosion tests in 3%NaCl solution show that the deposited layers have a high corrosion resistance compared to unalloyed steel substrate.

  10. KEYHOLE IMAGE PROCESSING OF VARIABLE POLARITY PLASMA ARC WELDING BASED ON WAVELET TRANSFORM

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In order to realize the feedback control for variable polarity plasma arc welding (VPPAW) formation in the welding process, the geometrical sizes of the keyhole image must be extracted. With the properties of multiscale edge through the wavelet theory, the edge points were detected by getting the maximum modules of the gradient vector in the dircetion towards which the gradient vector points in the image plane. At coarse scales, the local maxima of modules have different positions and only detected the sharp edge. At fine scale, there are many maxima created by the image noise. The best scale where the edges are well discriminated from noises is discussed by the multiscale transform. At last, a new method of peak analysis for threshold selection is provided. It is based on the wavelet transform which provides a multiscale analysis of the information of the histogram. Many experiments show these ways are effective for the keyhole image to get the geometry parameters of the keyhole in the real-time VPPAW image processing.

  11. Gas Sensors Based on Tin Oxide Nanoparticles Synthesized from a Mini-Arc Plasma Source

    Directory of Open Access Journals (Sweden)

    Ganhua Lu

    2006-01-01

    Full Text Available Miniaturized gas sensors or electronic noses to rapidly detect and differentiate trace amount of chemical agents are extremely attractive. In this paper, we report on the fabrication and characterization of a functional tin oxide nanoparticle gas sensor. Tin oxide nanoparticles are first synthesized using a convenient and low-cost mini-arc plasma source. The nanoparticle size distribution is measured online using a scanning electrical mobility spectrometer (SEMS. The product nanoparticles are analyzed ex-situ by high resolution transmission electron microscopy (HRTEM for morphology and defects, energy dispersive X-ray (EDX spectroscopy for elemental composition, electron diffraction for crystal structure, and X-ray photoelectron spectroscopy (XPS for surface composition. Nonagglomerated rutile tin oxide (SnO2 nanoparticles as small as a few nm have been produced. Larger particles bear a core-shell structure with a metallic core and an oxide shell. The nanoparticles are then assembled onto an e-beam lithographically patterned interdigitated electrode using electrostatic force to fabricate the gas sensor. The nanoparticle sensor exhibits a fast response and a good sensitivity when exposed to 100 ppm ethanol vapor in air.

  12. Determination of Nickel, Vanadium and Iron in Crude Oil by Three-Phase Plasma Arc Spectrometry

    Science.gov (United States)

    Ghatass, Zekry F.

    2002-12-01

    Three-phase plasma arc (TPPA) with ultrasonic nebulizer is developed for simultaneous determination of trace elements in crude oil samples. Ultrasonic nebulizer is used instead of pneumatic nebulizer in order to minimize the problems caused by the oil viscosity during the operation. This system was used for determination of some trace elements (V, Ni, and Fe) in a crude oil samples. Methyl isobutyl ketone (MIBK) was used to dilute the oil samples. The TPPA instrument offers several advantages including a low cost power supply with no radio frequency, linear dynamic ranges from 4 to 5 of orders of magnitude, and detection limits (0.121, 0.313 and 0.242 (μg/ml) for Ni, V and Fe respectively. The average concentrations were 31 ± 0.45 (μg/ml) for Ni, 40 ± 0.88 (μg/ml) for V and 8 ± 0.74 (μg/ml) for Fe at Balaaiem fields and 2 ± 0.05 (μg/ml) for Ni, 4.8 ± 0.25 (μg/ml) for V and 2 ± 0.10 (μg/ml) for Fe at Wastern Desert fields.

  13. Microscopy of Alloy Formation on Arc Plasma Sintered Oxide Dispersion Strengthen (ODS) Steel

    Science.gov (United States)

    Bandriyana, B.; Sujatno, A.; Salam, R.; Dimyati, A.; Untoro, P.

    2017-07-01

    The oxide dispersed strengthened (ODS) alloys steel developed as structure material for nuclear power plants (NPP) has good resistant against creep due to their unique microstructure. Microscopy investigation on the microstructure formation during alloying process especially at the early stages was carried out to study the correlation between structure and property of ODS alloys. This was possible thanks to the arc plasma sintering (APS) device which can simulate the time dependent alloying processes. The ODS sample with composition of 88 wt.% Fe and 12 wt.% Cr powder dispersed with 1 wt.% ZrO2 nano powder was mixed in a high energy milling, isostatic compressed to form sample coins and then alloyed in APS. The Scanning Electron Microscope (SEM) with X-ray Diffraction Spectroscopy (EDX) line scan and mapping was used to characterize the microstructure and elemental composition distribution of the samples. The alloying process with unification of each Fe and Cr phase continued by the alloying formation of Fe-Cr by inter-diffusion of both Fe and Cr and followed by the improvement of the mechanical properties of hardness.

  14. Enhanced human bone marrow mesenchymal stem cell functions on cathodic arc plasma-treated titanium.

    Science.gov (United States)

    Zhu, Wei; Teel, George; O'Brien, Christopher M; Zhuang, Taisen; Keidar, Michael; Zhang, Lijie Grace

    2015-01-01

    Surface modification of titanium for use in orthopedics has been explored for years; however, an ideal method of integrating titanium with native bone is still required to this day. Since human bone cells directly interact with nanostructured extracellular matrices, one of the most promising methods of improving titanium's osseointegration involves inducing bio-mimetic nanotopography to enhance cell-implant interaction. In this regard, we explored an approach to functionalize the surface of titanium by depositing a thin film of textured titanium nanoparticles via a cathodic arc discharge plasma. The aim is to improve human bone marrow mesenchymal stem cell (MSC) attachment and differentiation and to reduce deleterious effects of more complex surface modification methods. Surface functionalization was analyzed by scanning electron microscopy, atomic force microscopy, contact angle testing, and specific protein adsorption. Scanning electron microscopy and atomic force microscopy examination demonstrate the deposition of titanium nanoparticles and the surface roughness change after coating. The specific fibronectin adsorption was enhanced on the modified titanium surface that associates with the improved hydrophilicity. MSC adhesion and proliferation were significantly promoted on the nanocoated surface. More importantly, compared to bare titanium, greater production of total protein, deposition of calcium mineral, and synthesis of alkaline phosphatase were observed from MSCs on nanocoated titanium after 21 days. The method described herein presents a promising alternative method for inducing more cell favorable nanosurface for improved orthopedic applications.

  15. High temperature Oxidation of ODS alloy with zirconia dispersions synthesized using Arc Plasma Sintering

    Science.gov (United States)

    Bandriyana; Sujatno, A.; Salam, R.; Sugeng, B.; Dimyati, A.

    2017-02-01

    Microstructure formation and oxidation behaviour of the Oxide Dispersion Strengthened (ODS) steels for application as structure material in Nuclear Power Plant was investigated. A mixture composed of Fe and 12 wt. % Cr powder with addition of 0.5 and 1 wt.% ZrO2 particles was milled and isostatic pressed to form a sample coin. The coin was then consolidated in the Arc Plasma Sintering (APS) for 4 minutes. The samples were subjected to the high temperature oxidation test in the Magnetic Suspension Balance (MSB). The oxidation test was carried out at 700°C for 6 hours to evaluate the oxide growth in the early stage of it formation by extraction the mass gain curve. The Scanning Electron Microscope (SEM) imaging and X-ray Diffraction Spectroscopy (EDX) elemental mapping were performed to study the microstructure change and compositional distribution. SEM and EDX observation revealed the time dependent development of the Fe-Cr-phases during consolidation. The oxidation rate behaviour of the samples followed the parabolic rate characteristic for inward oxidation process driven by oxygen inward diffusion through the oxide scale with the maximum weight gain around of 60 g/m2. The oxidation resistance was strongly affected by the formation of the oxide protective layer on the surface. In so far, addition of zirconia particles has played no significant role to the oxidation behaviour.

  16. Development of an encapsulation method using plasma arc welding to produce iodine-125 seeds for brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Feher, Anselmo; Calvo, Wilson A.P.; Rostelato, Maria E.C.M.; Zeituni, Carlos A.; Somessari, Samir L.; Costa, Osvaldo L.; Moura, Joao A.; Moura, Eduardo S.; Souza, Carla D.; Rela, Paulo R., E-mail: afeher@ipen.b, E-mail: wapcalvo@ipen.b, E-mail: elisaros@ipen.b, E-mail: somessar@ipen.b, E-mail: olcosta@ipen.b, E-mail: esmoura@ipen.b, E-mail: cdsouza@ipen.b, E-mail: prela@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    The prostate cancer, which is the second cause of death by cancer in men, overcome only by lung cancer is public health problem in Brazil. Brachytherapy is among the possible available treatments for prostate cancer, in which small seeds containing Iodine-125 radioisotope are implanted into the prostate gland. The seed consists of a titanium sealed capsule with 0.8 mm external diameter and 4.5 mm length, containing a central silver wire with adsorbed Iodine-125. The Plasma Arc Welding (PAW) is one of the viable techniques for sealing process. The equipment used in this technique is less costly than in other processes, such as, Laser Beam Welding (LBW). The main purpose of this work was the development of an encapsulation method using PAW. The development of this work has presented the following phases: cutting and cleaning titanium tube, determination of the welding parameters, development of a titanium tube holding device for PAW, sealed sources validation according to ISO 2919 - Sealed Radioactive Sources - General Requirements and Classification, and metallographic assays. The developed procedure to seal Iodine-125 seeds using PAW has shown high efficiency, satisfying all the established requirements of ISO 2919. The results obtained in this work will give the possibility to establish a routine production process according to the orientations presented in resolution RDC 17 - Good Manufacturing Practices to Medical Products defined by the ANVISA - National Agency of Sanitary Surveillance. (author)

  17. Particle Size and Pore Structure Characterization of Silver Nanoparticles Prepared by Confined Arc Plasma

    Directory of Open Access Journals (Sweden)

    Mingru Zhou

    2009-01-01

    Full Text Available In the protecting inert gas, silver nanoparticles were successfully prepared by confined arc plasma method. The particle size, microstructure, and morphology of the particles by this process were characterized via X-ray powder diffraction (XRD, transmission electron microscopy (TEM and the corresponding selected area electron diffraction (SAED. The N2 absorption-desorption isotherms of the samples were measured by using the static volumetric absorption analyzer, the pore structure of the sample was calculated by Barrett-Joyner-Halenda (BJH academic model, and the specific surface area was calculated from Brunauer-Emmett-Teller (BET adsorption equation. The experiment results indicate that the crystal structure of the samples is face-centered cubic (FCC structure the same as the bulk materials, the particle size distribution ranging from 5 to 65 nm, with an average particle size about 26 nm obtained by TEM and confirmed by XRD and BET results. The specific surface area is 23.81 m2/g, pore volumes are 0.09 cm3/g, and average pore diameter is 18.7 nm.

  18. Study of Raw Materials Treatment by Melting and Gasification Process in Plasma Arc Reactor

    Directory of Open Access Journals (Sweden)

    Peter KURILLA

    2010-12-01

    Full Text Available The world consumption of metals and energy has increased in last few decades and it is still increasing. Total volume production results to higher waste production. Raw material basis of majority metals and fossil fuels for energy production is more complex and current waste treatment has long term tendency. Spent power cells of different types have been unneeded and usually they are classified as dangerous waste. This important issue is the main topic of the thesis, in which author describes pyrometallurgical method for storage batteries – power cells and catalysts treatment. During the process there were tested a trial of spent NiMH, Li – ion power cells and spent copper catalysts with metal content treatment by melting and gasification process in plasma arc reactor. The synthetic gas produced from gasification process has been treated by cogenerations micro turbines units for energy recovery. The metal and slag from treatment process are produced into two separately phases and they were analyzing continually.

  19. An Experimental Research to Study the Microwaves Transmission Characteristics of Ablating Material in Arc-Heated Plasma Flow

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In this paper, an experimental research the effect of ablating material on the reflection and the transmission of microwaves in arc-heated plasma flow is presented by using the C band microwave measuring system. The results show that the ablating material with accidented surface and its high temperature have remarkably affected the reflection and the transmission of microwaves. The experiment proves that the system has outstanding precision and reliability.

  20. Effect of Fast Curing Lights, Argon Laser, and Plasma Arc on Bond Strengths of Orthodontic Brackets: An In Vitro Study

    Directory of Open Access Journals (Sweden)

    M. Hashem-Hoseini

    2008-12-01

    Full Text Available Objective: Nowadays light-cured composites are used widely by orthodontists to bond brackets. As these composites require 20-40 seconds time per tooth to be light cured, more chair-time in needed compared to self-cured composites. In recent years, the argon laser and plasma arc lights have been introduced in dentistry to reduce this curing time. The purpose of this study was to compare bond strength of brackets bonded with the argon la-ser and plasma arc light with those bonded with the conventional halogen light.Materials and Methods: Fifty-one intact human premolars were randomly divided into three groups of 17 teeth each. Stainless steel twin premolar brackets (018- in Dyna lock, 3M Unitek were bonded to the teeth using one of these curing devices in each group: the halogen unit (Coltolux 75, Switzerland, the argon laser unit (Bo-5, Iran , and the plasma arc unit (Remecure 15, Belgium. The orthodontic adhesive was the same in the three groups (Transbond XT, 3M Unitek. After thermal cycling, the diametral tensilebond strength of specimens was measured using a debonding plier in a Zwick Universal Testing machine (Z/100, Germany.Results: The mean bond strengths was 17.344 MPa (SD=4.567 for halogen 19.172 MPa(SD=6.328 for laser and 19.322 MPa (SD=4.036 for plasma arc groups. No statistically significant difference existed in the mean bond strengths among three groups.Conclusion: Argon laser lights, significantly reducing the curing time of orthodonticbrackets without affecting bond strength, have the potential to be considered as advanta-geous alternatives to conventional halogen light.

  1. Negative transferred arc cleaning: a method for roughening and removing surface contamination from beryllium and other metallic surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Hollis, K.J.; Maggiore, C.J.; Ayala, A.; Bartram, B.D. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.; Doerner, R.P. [California Univ., San Diego (United States). Fusion Energy Res.

    2000-04-01

    TA cleaning has been investigated for preparing the surface of beryllium plasma facing components (PFC's) inside of the international thermonuclear experimental reactor (ITER) prior to depositing beryllium by plasma spraying. Plasma spraying of beryllium was evaluated during the ITER engineering design activity (EDA) for in-situ repair and initial fabrication of the beryllium first wall armor. Results have shown that surface roughening of beryllium, during the TA cleaning process, can result in bond strengths greater than 100 MPa between beryllium surfaces and plasma sprayed beryllium. In addition, the TA cleaning process was shown to be an effective method for removing contaminate layers of carbon and tungsten from the surface of beryllium. Investigations have been performed to characterize the different arc-types that occur during the TA cleaning process (type I, I and III arcs) and the effectiveness of the TA cleaning process for potentially removing co-deposited layers of carbon and deuterium from the surface of beryllium, stainless steel and tungsten. (orig.)

  2. Micro-leakage of a Fissure Sealant Cured Using Quartz-tungsten-halogen and Plasma Arc Light Curing Units.

    Science.gov (United States)

    Bahrololoomi, Zahra; Soleimani, Ali Asghar; Jafari, Najmeh; Varkesh, Bentolhoda

    2014-01-01

    Background and aims. Newer curing units such as plasma arc can polymerize the sealants in much shorter curing times. The aim of this study was to compare the effect of two different curing units on the micro-leakage of a fissure sealant material. Materials and methods. Sixty two extracted premolars without caries were randomly divided into two groups of 31 samples. Occlusal surfaces of all teeth were cleansed. Then, teeth surfaces were etched by 37% phosphoric acid. After rinsing and drying, occlusal surfaces of teeth were sealed by a fissure sealant. The sealant was then cured using either a halogen light curing unit or a plasma arc curing light. After sealing, the teeth were thermocycled for 500 cycles. The teeth were then sectioned and examined for micro-leakage. Statistical analyses were performed with Mann-Whitney test. Results. There was no significant difference between two groups regarding micro-leakage (P = 0.42). Conclusion. Results showed that there was no significant difference between two different curing units. Therefore, plasma arc unit might be a useful alternative for sealant polymerization.

  3. Investigation in the use of plasma arc welding and alternative feedstock delivery method in additive manufacture

    Science.gov (United States)

    Alhuzaim, Abdullah F.

    The work conducted for this thesis was to investigate the use of plasma arc welding (PAW) and steel shot as a means of additive manufacturing. A robotic PAW system and automatic shot feeder were used to manufacture linear walls approximately 100 mm long by 7 mm wide and 20 mm tall. The walls were built, layer-by-layer, on plain carbon steel substrate by adding individual 2.5 mm diameter plain carbon steel shot. Each layer was built, shot-by-shot, using a pulse of arc current to form a molten pool on the deposit into which each shot was deposited and melted. The deposition rate, a measure of productivity, was approximately 50 g/hour. Three walls were built using the same conditions except for the deposit preheat temperature prior to adding each new layer. The deposit preheat temperature was controlled by allowing the deposit to cool after each layer for an amount of time called the inter-layer wait time. The walls were sectioned and grain size and hardness distribution were measured as a function of wall height. The results indicated that, for all specimens, deposit grain size increased and hardness decreased as wall height increased. Furthermore, average grain size decreased and hardness increased as interlayer wait time increased. An analytical heat flow model was developed to study the influence of interlayer wait time on deposit temperature and therefore grain size and hardness. The results of the model indicated that as wall height increased, the rate of deposit heat removal by conduction to the substrate decreased leading to a higher preheat temperature after a fixed interlayer wait time causing grain size to increase as wall height increased. However, the model results also show that as wall height increased, the deposit surface area from which heat energy is lost via convection and radiation increased. The model also demonstrated that the use of a means of forced convection to rapidly remove heat from the deposit could be an effective way to boost

  4. Plasma-puff initiation of high Coulomb transfer switches

    Science.gov (United States)

    Han, Kwang S.; Venable, Demetrius D.; Lee, Ja H.; Choi, Eun H.; Kim, Y. K.; Kim, J. H.; Nguyen, D. X.

    1993-01-01

    The plasma-puff triggering mechanism based on a hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for an azimuthally uniform surface flashover which initiates plasma-puff under wide ranges of fill gas pressures of Ar, He and N2. The optimal fill gas pressures for the azimuthally uniform plasma-puff were about 120 mTorr less than P(sub opt) less than 450 Torr for He and N2. For Argon 20 mTorr is less than P(sub opt) is less than 5 Torr. The inverse pinch switch was triggered with the plasma-puff and the switching capability under various electrical parameters and working gas pressures of Ar, He and N2 was determined. It was also shown that the azimuthally uniform switching discharges were dependent on the type of fill gas and its fill pressure. A new concept of plasma-focus driven plasma-puff was also discussed in comparison with hypocycloidal pinch plasma-puff triggering. The main discharge of the inverse pinch switch with the plasma-focus driven plasma-puff trigger is found to be more azimuthally uniform than that with the hypocycloidal pinch plasma-puff trigger in a gas pressure region between 80 mTorr and 1 Torr. In order to assess the effects of plasma current density on material erosion of electrodes, emissions from both an inverse-pinch plasma switch (INPIStron) and from a spark gap switch under test were studied with an optical multichannel analyzer (OMA). The color temperature of the argon plasma was approximately 4,000 K which corresponded with the peak continuum emission near 750 nm. There are the strong line emissions of argon in the 650 - 800 nm range and a lack of line emissions of copper and other solid material used in the switch. This indicates that the plasma current density during closing is low and the hot spot or hot filament in the switch is negligible. This result also indicates considerable reduction of line emission with the INPIStron switch over that of a spark-gap switch. However, a strong carbon

  5. Energy transfer and dual cascade in kinetic magnetized plasma turbulence.

    Science.gov (United States)

    Plunk, G G; Tatsuno, T

    2011-04-22

    The question of how nonlinear interactions redistribute the energy of fluctuations across available degrees of freedom is of fundamental importance in the study of turbulence and transport in magnetized weakly collisional plasmas, ranging from space settings to fusion devices. In this Letter, we present a theory for the dual cascade found in such plasmas, which predicts a range of new behavior that distinguishes this cascade from that of neutral fluid turbulence. These phenomena are explained in terms of the constrained nature of spectral transfer in nonlinear gyrokinetics. Accompanying this theory are the first observations of these phenomena, obtained via direct numerical simulations using the gyrokinetic code AstroGK. The basic mechanisms that are found provide a framework for understanding the turbulent energy transfer that couples scales both locally and nonlocally.

  6. Experimental research on electrical propulsion. Note 2: Experimental research on a plasma jet with vortex type stabilization for propulsion

    Science.gov (United States)

    Robotti, A. C.; Oggero, M.

    1985-01-01

    Results of experimental electric propulsion research are presented. A plasma generator, with an arc stabilized by an air vortex is examined. The heat transfer efficiency between arc and fluid environment at a varying current and flow rate is discussed.

  7. Modeling Arcs

    CERN Document Server

    Insepov, Zeke; Veitzer, Seth; Mahalingam, Sudhakar

    2011-01-01

    Although vacuum arcs were first identified over 110 years ago, they are not yet well understood. We have since developed a model of breakdown and gradient limits that tries to explain, in a self-consistent way: arc triggering, plasma initiation, plasma evolution, surface damage and gra- dient limits. We use simple PIC codes for modeling plasmas, molecular dynamics for modeling surface breakdown, and surface damage, and mesoscale surface thermodynamics and finite element electrostatic codes for to evaluate surface properties. Since any given experiment seems to have more variables than data points, we have tried to consider a wide variety of arcing (rf structures, e beam welding, laser ablation, etc.) to help constrain the problem, and concentrate on common mechanisms. While the mechanisms can be comparatively simple, modeling can be challenging.

  8. Adding high time resolution to charge-state-specific ion energy measurements for pulsed copper vacuum arc plasmas

    CERN Document Server

    Tanaka, Koichi; Zhou, Xue; Anders, André

    2015-01-01

    Charge-state-resolved ion energy-time-distributions of pulsed Cu arc plasma were obtained by using direct (time dependent) acquisition of the ion detection signal from a commercial ion mass-per-charge and energy-per-charge analyzer. We find a shift of energies of Cu2+, Cu3+ and Cu4+ ions to lower values during the first few hundred microseconds after arc ignition, which is evidence for particle collisions in the plasma. The generation of Cu1+ ions in the later part of the pulse, measured by the increase of Cu1+ signal intensity and an associated slight reduction of the mean charge state point to charge exchange reactions between ions and neutrals. At the very beginning of the pulse, when the plasma expands into vacuum and the plasma potential strongly fluctuates, ions with much higher energy (over 200 eV) were observed. Early in the pulse, the ion energies observed are approximately proportional to the ion charge state, and we conclude that the acceleration mechanism is primarily based on acceleration in an e...

  9. Plasma synthesis of titanium nitride, carbide and carbonitride nanoparticles by means of reactive anodic arc evaporation from solid titanium

    Energy Technology Data Exchange (ETDEWEB)

    Kiesler, D., E-mail: dennis.kiesler@uni-due.de; Bastuck, T.; Theissmann, R.; Kruis, F. E. [University of Duisburg-Essen, Institute of Technology for Nanostructures (NST) and Center for Nanointegration Duisburg-Essen (CENIDE) (Germany)

    2015-03-15

    Plasma methods using the direct evaporation of a transition metal are well suited for the cost-efficient production of ceramic nanoparticles. In this paper, we report on the development of a simple setup for the production of titanium-ceramics by reactive anodic arc evaporation and the characterization of the aerosol as well as the nanopowder. It is the first report on TiC{sub X}N{sub 1 − X} synthesis in a simple anodic arc plasma. By means of extensive variations of the gas composition, it is shown that the composition of the particles can be tuned from titanium nitride over a titanium carbonitride phase (TiC{sub X}N{sub 1 − X}) to titanium carbide as proven by XRD data. The composition of the plasma gas especially a very low concentration of hydrocarbons around 0.2 % of the total plasma gas is crucial to tune the composition and to avoid the formation of free carbon. Examination of the particles by HR-TEM shows that the material consists mostly of cubic single crystalline particles with mean sizes between 8 and 27 nm.

  10. Influence of gas pressure on electron beam emission current of pulsed cathodic-arc-based forevacuum plasma electron source

    Science.gov (United States)

    Burdovitsin, Victor A.; Kazakov, Andrey V.; Medovnik, Alexander V.; Oks, Efim M.

    2017-09-01

    We describe our experimental investigation of the effect of background gas pressure on the emission parameters of a pulsed cathodic-arc-based forevacuum-pressure plasma-cathode electron source. We find that increased gas pressure over the range 4-16 Pa significantly reduces the beam current rise-time and significantly increases the emission current amplitude. For example, at a discharge current of 20 A, increasing the working gas pressure from 4 Pa to 16 Pa increases the emission current from 8 A to 18 A and shortens the beam rise-time from 50 μs to 20 μs. This influence of gas pressure on the electron beam parameters can be explained by the effect of arc discharge current switching from the anode to emission. In our case, the current switching effect is caused by increased working gas pressure. In the forevacuum pressure range, the increase of the electron emission current with the growth of gas pressure is due to a rise in the emission plasma potential which is caused by ion back-streaming from the plasma formed in the electron beam transport region. A model describing the influence of gas pressure on the electron emission from the plasma is presented.

  11. 双丝间接电弧氩气保护焊的熔滴过渡与电弧形态%Relationship between metal transfer and arc shape in twin-wire indirect arc welding

    Institute of Scientific and Technical Information of China (English)

    曹梅青; 邹增大; 曲仕尧

    2012-01-01

    用高速摄像系统及示波器对双丝间接电弧氩弧焊的熔滴过渡及电弧形态和电弧电压之间的关系进行了深入分析.结果表明,熔滴过渡和电弧电压、电弧形态的规律性变化存在密切的对应关系.熔滴形成、长大、脱离焊丝端部的规律性变化使极性斑点间距及弧柱电阻发生变化导致了电弧电压的波动,从而使电弧形态发生由暗到明、由小到大的规律性变化.随着焊接电流的增大熔滴的过渡形式发生变化,熔滴尺寸减小.不同的熔滴过渡形式其电弧电压的波动也有所不同,射流过渡电压波动较小,而短路过渡电弧电压的波动最大.%Relationship between metal transfer,arc shape and arc voltage was investigated with high speed camcorder system and digital oscillograph.Results show that metal transfer has a close relationship with arc voltage and the regular variation of arc shape.It shows that the regular changes of metal transfer make polarity spots spacing and arc beam resistance change and cause the arc voltage fluctuations,so that the arc shape changes regularly.Droplet transfer pattern changes and droplet size dereases with the increasing of welding current,different metal transfer mode has different arc voltage fluctuation,spraying transfer has lower variation of voltage but short transfer's arc voltage variation is bigger.

  12. Investigation of plasma hydrogenation and trapping mechanism for layer transfer

    Science.gov (United States)

    Chen, Peng; Chu, Paul K.; Höchbauer, T.; Lee, J.-K.; Nastasi, M.; Buca, D.; Mantl, S.; Loo, R.; Caymax, M.; Alford, T.; Mayer, J. W.; Theodore, N. David; Cai, M.; Schmidt, B.; Lau, S. S.

    2005-01-01

    Hydrogen ion implantation is conventionally used to initiate the transfer of Si thin layers onto Si wafers coated with thermal oxide. In this work, we studied the feasibility of using plasma hydrogenation to replace high dose H implantation for layer transfer. Boron ion implantation was used to introduce H-trapping centers into Si wafers to illustrate the idea. Instead of the widely recognized interactions between boron and hydrogen atoms, this study showed that lattice damage, i.e., dangling bonds, traps H atoms and can lead to surface blistering during hydrogenation or upon postannealing at higher temperature. The B implantation and subsequent processes control the uniformity of H trapping and the trap depths. While the trap centers were introduced by B implantation in this study, there are many other means to do the same without implantation. Our results suggest an innovative way to achieve high quality transfer of Si layers without H implantation at high energies and high doses.

  13. PRELIMINARY STUDY OF COMBINED PULSED VACUUM ARC SOURCE PLASMA%组合体脉冲真空电弧源的初步研究

    Institute of Scientific and Technical Information of China (English)

    李璟; 黄杰; 王锴; 张荟星; 彭建华; 邓春凤; 吴先映

    2014-01-01

    为得到高密度的等离子体,设计研制了组合体脉冲真空电弧源,它由4套脉冲真空电弧源组合而成.测量了脉冲真空电弧源弧压与弧流的关系;利用静电探针测量了组合体脉冲真空电弧源和单套脉冲真空电弧源产生的等离子体,得到了探针饱和电流(与等离子体密度成正比)与弧压的关系,以及等离子体密度的轴向分布情况;采用飞行时间方法估测了等离子体的飞行速度.组合脉冲真空电弧源最大等离子体密度达到8×1012 cm-3.%In order to get high density plasma,a combined pulsed vacuum arc source is designed and developed with four pulsed vacuum arc sources.The relationship of arc voltage and arc current is measured;The plasma in combined pulsed vacuum arc source and single pulsed vacuum arc source are measured using electrical probe.The relationship of probe saturation current (in proportion to plasma density)versus arc voltage and axial distribution of plasma are measured;The plasma velocity is estimated using time-of-flight method.The maximal plasma density in combined pulsed vacuum arc source is 8×1012 cm-3 .

  14. Ion angular distribution in plasma of vacuum arc ion source with composite cathode and elevated gas pressure.

    Science.gov (United States)

    Nikolaev, A G; Savkin, K P; Yushkov, G Yu; Oks, E M

    2014-02-01

    The Metal Vapor Vacuum Arc (MEVVA) ion sources are capable of generating ion beams of almost all metals of the periodic table. For this kind of ion source, a combination of gas feeding with magnetic field allows the simultaneous generation of both metal and gaseous ions. That makes the MEVVA ion source an excellent instrument for science and application. This work presents results of investigation for ion angular distributions in vacuum arc plasma of Mevva-V.Ru ion source for composite cathodes and for elevated gas pressure. It was shown that for all the cathode materials, singly charged ions have wider angular distribution than multiply charged ions. Increasing the working gas pressure leads to a significant change in the angular distribution of gaseous ions, while with the distribution of metal ions gas remains practically unchanged. The reasons for such different influences are discussed.

  15. Incineration/vitrification of radioactive wastes and combustion of pyrolysis gases in thermal plasmas; Incineration/vitrification de dechets radioactifs et combustion de gaz de pyrolyse en plasma d`arc

    Energy Technology Data Exchange (ETDEWEB)

    Girold, Ch. [CEA de la Vallee du Rhone, Departement de Retraitement des Dechets et du Demantelemnet, 30 - Marcoule (France)]|[Limoges Univ., 87 (France)

    1997-03-01

    Two thermal plasma processes used for incineration of radioactive technological wastes (cellulose, plastics, rubber...) have been investigated. First, the different types of radioactive wastes are presented, with a special attention to those which may benefit from a high temperature thermal treatment. The most significant thermal plasma processes, suitable for this goal, are described. Then, the author deals with the post-combustion, in an oxygen plasma jet reactor, of gases from burnable radioactive waste pyrolysis. An experimental planning method as been used to evaluate the combustion performances in the reactor, with a wide range of gas composition and running parameters such as oxygen excess and electrical power. The results of a modeling of kinetics, based on 116 chemicals reactions between 25 species, are compared with experimental values. Finally, an oxygen plasma reactor where the arc is transferred on a basalt melt is experimented. The efficiency of the combustion and the homogeneity of the glass are discussed. The volatility of some glass elements and tracers added to the wastes is also approached in two different ways: by post-trial material balance and by an optical emission spectroscopic method. The author built a diagnostic method that allows the following versus time of the metallic vapours above the melt. (author) 51 refs.

  16. Mathematical modeling of motion of interacting particles on the basis of the distribution functions in the plasma arc synthesis of ONS

    Directory of Open Access Journals (Sweden)

    G. V. Abramov

    2012-01-01

    Full Text Available The model of the motion of particles in a plasma arc discharge with binary collisions in the synthesis of carbon nanostructures such as fullerenes and nanotubes Rena. The solution of the system of dimensionless equations of the Vlasov-Poisson equations for the determination of the distribution functions of particles in the plasma.

  17. Investigations of the cathode region of an argon arc plasma by degenerate four-wave mixing laser spectroscopy and optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Dzierzega, K [Marian Smoluchowski Institute of Physics, Jagiellonian University, ul. Reymonta 4, 30-059 Cracow (Poland); Pokrzywka, B [Mt. Suhora Observatory, Cracow Pedagogical University, ul. Podchorazych 2, 30-083 Cracow (Poland); Pellerin, S [LASEP, Universite d' Orleans-Centre Universitaire de Bourges, Rue Gaston Berger BP 4043, 18028 Bourges (France)

    2004-07-07

    Degenerate four-wave mixing (DFWM) laser spectroscopy was used in local studies of atmospheric pressure argon plasma generated in a free-burning arc. The results of plasma diagnostics using the DFWM method were compared to the results obtained with optical emission measurements. In the cathode region of the arc the maxima of both the DFWM signal and the emission coefficient for the 696.5 nm Ar I line depend on the distance from the cathode tip. This effect proves the departure of the plasma state from local thermal equilibrium (LTE) as it has been reported by many authors. On the other hand the Stark shifts of the 696.5 nm Ar I line determined by the DFWM method in relation to plasma diagnostic results show no deviations from LTE on the arc axis down to 1.0 mm from the cathode tip.

  18. Ion sources with arc-discharge plasma box driven by directly heated LaB(6) electron emitter or cold cathode.

    Science.gov (United States)

    Ivanov, Alexander A; Davydenko, Vladimir I; Deichuli, Petr P; Shulzhenko, Grigori I; Stupishin, Nikolay V

    2008-02-01

    In the Budker Institute, Novosibirsk, an ion source with arc-discharge plasma box has been developed in the recent years for application in thermonuclear devices for plasma diagnostics. Several modifications of the ion source were provided with extracted current ranging from 1 to 7 A and pulse duration of up to 4 s. Initially, the arc-discharge plasma box with cold cathode was used, with which pulse duration is limited to 2 s by the cathode overheating and sputtering in local arc spots. Recently, a directly heated LaB(6) electron emitter was employed instead, which has extended lifetime compared to the cold cathode. In the paper, characteristics of the beam produced with both arrangements of the plasma box are presented.

  19. Momentum and Energy Dependent Resolution Function of the ARCS Neutron Chopper Spectrometer at High Momentum Transfer: Comparing Simulation and Experimen

    CERN Document Server

    Diallo, S O; Abernathy, D L; Azuah, R T

    2016-01-01

    Inelastic neutron scattering at high momentum transfers (i.e. $Q\\ge20$ {\\AA}) or DINS provides direct observation of the momentum distribution of light atoms, making it a powerful probe for studying single-particle motions in liquids and solids. The quantitative analysis of DINS data requires an accurate knowledge of the instrument resolution function $R_{i}({Q},E)$ at each $Q$ and energy transfer $E$, where the label $i$ indicates whether the resolution was experimentally observed $i={obs}$ or simulated $i=sim$. Here, we describe two independent methods for determining the total resolution function $R_{i}({Q},E)$ of the ARCS neutron instrument at the Spallation Neutron Source, Oak Ridge National Laboratory. The first method uses experimental data from an archetypical system (liquid $^4$He) studied with DINS, which are then numerically deconvoluted using its previously determined intrinsic scattering function to yield $R_{obs}({Q},E)$. The second approach uses accurate Monte Carlo simulations of the ARCS spec...

  20. Photoelectron Emission from Metal Surfaces Induced by VUV-emission of Filament Driven Hydrogen Arc Discharge Plasma

    CERN Document Server

    Laulainen, J; Koivisto, H; Komppula, J; Tarvainen, O

    2015-01-01

    Photoelectron emission measurements have been performed using a filament-driven multi-cusp arc discharge volume production H^- ion source (LIISA). It has been found that photoelectron currents obtained with Al, Cu, Mo, Ta and stainless steel (SAE 304) are on the same order of magnitude. The photoelectron currents depend linearly on the discharge power. It is shown experimentally that photoelectron emission is significant only in the short wavelength range of hydrogen spectrum due to the energy dependence of the quantum efficiency. It is estimated from the measured data that the maximum photoelectron flux from plasma chamber walls is on the order of 1 A per kW of discharge power.

  1. Photoelectron emission from metal surfaces induced by VUV-emission of filament driven hydrogen arc discharge plasma

    Science.gov (United States)

    Laulainen, J.; Kalvas, T.; Koivisto, H.; Komppula, J.; Tarvainen, O.

    2015-04-01

    Photoelectron emission measurements have been performed using a filament-driven multi-cusp arc discharge volume production H- ion source (LIISA). It has been found that photoelectron currents obtained with Al, Cu, Mo, Ta and stainless steel (SAE 304) are on the same order of magnitude. The photoelectron currents depend linearly on the discharge power. It is shown experimentally that photoelectron emission is significant only in the short wavelength range of hydrogen spectrum due to the energy dependence of the quantum efficiency. It is estimated from the measured data that the maximum photoelectron flux from plasma chamber walls is on the order of 1 A per kW of discharge power.

  2. ZrO2 and ZrO2-Y2O3 coatings deposited by double pulsed plasma arc

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A novel surface technique has been developed to produce ZrO2 and ZrO2-Y2O3 coatings on the surface of alloys by using double pulsed plasma arc to react with a solution film containing nano-oxide particles. These coatings exhibit smooth surface and excellent adhesion with substrate. The morphologies of the ceramic coatings and phases were analyzed. It was shown that the oxidation resistance of l8-8 stainless steel was markedly improved by applying ZrO2 and ZrO2-Y2O3 coatings.

  3. Unstable Behavior of Anodic Arc Discharge for Synthesis of Nanomaterials

    Science.gov (United States)

    Gershman, Sophia; Raitses, Yevgeny

    2016-09-01

    Fast imaging and electrical current measurements reveal unstable behavior of the carbon arc discharge for synthesis of nanomaterials. The arc column and the arc attachment region to the anode move in a somewhat sporadic way with a characteristic time in a 10-3 sec range. The arc exhibits a negative differential resistance before the arc motion occurs. A physical mechanism is proposed based on the thermal processes in the arc plasma region interacting with the ablating anode which leads to the shift of the arc to a new anode region. According to the transient heat transfer analysis, the time needed to heat a new anode region is also in a 10-3 sec range. For a 0.6 cm diameter anode used in our experiments, this time yields a frequency of about 200-300 Hz, comparable to the measured frequency of the arc motion. The voltage and current measurements show oscillations with a similar characteristic frequency. The thermal model is indirectly supported by the measured negative differential resistance of the arc discharge during arc oscillations. The observed unstable behavior of the arc may be responsible for the mixing of the flow of nanoparticles during the synthesis of nanoparticles leading to poor selectivity typical for the arc synthesis. The work was supported by US DOE under Contract No. DE-AC02-09CH11466.

  4. Effects of shielding gas composition on arc profile and molten pool dynamics in gas metal arc welding of steels

    Science.gov (United States)

    Wang, L. L.; Lu, F. G.; Wang, H. P.; Murphy, A. B.; Tang, X. H.

    2014-11-01

    In gas metal arc welding, gases of different compositions are used to produce an arc plasma, which heats and melts the workpiece. They also protect the workpiece from the influence of the air during the welding process. This paper models gas metal arc welding (GMAW) processes using an in-house simulation code. It investigates the effects of the gas composition on the temperature distribution in the arc and on the molten pool dynamics in gas metal arc welding of steels. Pure argon, pure CO2 and different mixtures of argon and CO2 are considered in the study. The model is validated by comparing the calculated weld profiles with physical weld measurements. The numerical calculations reveal that gas composition greatly affects the arc temperature profile, heat transfer to the workpiece, and consequently the weld dimension. As the CO2 content in the shielding gas increases, a more constricted arc plasma with higher energy density is generated as a result of the increased current density in the arc centre and increased Lorentz force. The calculation also shows that the heat transferred from the arc to the workpiece increases with increasing CO2 content, resulting in a wider and deeper weld pool and decreased reinforcement height.

  5. The influence of arc plasma parameters on the form of a welding pool

    Science.gov (United States)

    Frolov, V. Ya.; Toropchin, A. I.

    2015-07-01

    The influence of the Marangoni force on the form of a welding pool has been considered. Results of computer simulation of the processes of welding arc generation with a non-consumable tungsten electrode in inert gas are shown. The experimental results are reported and comparatively analyzed. The calculations were carried out in a package of applied programs at various currents.

  6. High plasma cholesteryl ester transfer but not CETP mass predicts incident cardiovascular disease : A nested case control study

    NARCIS (Netherlands)

    Kappelle, Paul J.W.H.; Perton, Frank; Hillege, Hans L.; Dallinga-Thie, Geesje M.; Dullaart, Robin P. F.

    Objective: The relationship of cardiovascular disease (CVD) with plasma cholesteryl ester transfer protein (CETP) levels is controversial. We determined whether plasma cholesteryl ester transfer (CET), reflecting CETP-mediated transfer of cholesteryl esters from endogenous HDL towards apolipoprotein

  7. Study of Nanodispersed Iron Oxides Produced in Steel Drilling by Contracted Electric-Arc Air Plasma Torch

    Institute of Scientific and Technical Information of China (English)

    P. STEFANOV; D. GALANOV; G. VISSOKOV; D. PANEVA; B. KUNEV; I. MITOV

    2008-01-01

    The optimal conditions on the plasma-forming gas flowrate, discharge current and voltage, distance between the plasma-torch nozzle and the metal plate surface for the process of penetration in and vaporization of steel plates by the contracted electric-arc air plasma torch accompanied by water quenching, were determined. The X-ray structural and phase studies as well as M6ssbauer and electron microscope studies on the samples treated were performed. It was demonstrated that the vaporized elemental iron was oxidized by the oxygen present in the air plasma jet to form iron oxides (wiistite, magnetite, hematite), which, depending on their mass ra-tios, determined the color of the iron oxide pigments, namely, beginning from light yellow, through deep yellow, light brown, deep brown, violet, red-violet, to black. A high degree of dispersity of the iron oxides is thus produced, with an averaged diameter of the particles below 500 nm, and their defective crystal structure form the basis of their potential application as components of iron-containing catalysts and pigments.

  8. Study of Nanodispersed Iron Oxides Produced in Steel Drilling by Contracted Electric-Arc Air Plasma Torch

    Science.gov (United States)

    Stefanov, P.; Galanov, D.; Vissokov, G.; Paneva, D.; Kunev, B.; Mitov, I.

    2008-06-01

    The optimal conditions on the plasma-forming gas flowrate, discharge current and voltage, distance between the plasma-torch nozzle and the metal plate surface for the process of penetration in and vaporization of steel plates by the contracted electric-arc air plasma torch accompanied by water quenching, were determined. The X-ray structural and phase studies as well as Mössbauer and electron microscope studies on the samples treated were performed. It was demonstrated that the vaporized elemental iron was oxidized by the oxygen present in the air plasma jet to form iron oxides (wüstite, magnetite, hematite), which, depending on their mass ratios, determined the color of the iron oxide pigments, namely, beginning from light yellow, through deep yellow, light brown, deep brown, violet, red-violet, to black. A high degree of dispersity of the iron oxides is thus produced, with an averaged diameter of the particles below 500 nm, and their defective crystal structure form the basis of their potential application as components of iron-containing catalysts and pigments.

  9. Arc erosion of full metal plasma facing components at the inner baffle region of ASDEX Upgrade

    Directory of Open Access Journals (Sweden)

    V. Rohde

    2016-12-01

    Full Text Available At the inner baffle of the AUG divertor massive polished inserts of tungsten and P92 steel were installed to measure the erosion by arcing. For tungsten most of the traces are less than 0.4µm deep and a similar amount of tungsten is deposited close to the traces. Few craters up to 4µm resulting in an average erosion rate of 2×1013 at cm−2s−1 are observed. The behaviour for P92 steel is quite different: most of the traces are 4µm deep, up to 80µm were observed. An average erosion rate of 400×1013 at cm−2s−1, i.e. more than a factor of hundred higher compared to tungsten, is found. Therefore, erosion by arcing has to be taken into account to determine the optimal material mix for future fusion devices.

  10. Transfer fault earthquake in compressionally reactivated back-arc failed rift: 1948 Fukui earthquake (M7.1), Japan

    Science.gov (United States)

    Ishiyama, Tatsuya; Kato, Naoko; Sato, Hiroshi; Koshiya, Shin

    2017-04-01

    Back-arc rift structures in many subduction zones are recognized as mechanically and thermally weak zones that possibly play important roles in strain accommodation at later post-rift stages within the overriding plates. In case of Miocene back-arc failed rift structures in the Sea of Japan in the Eurasian-Pacific subduction system, the mechanical contrasts between the crustal thrust wedges of the pre-rift continental crust and high velocity lower crust have fundamentally controlled the styles of post-rift, Quaternary active deformation (Ishiyama et al. 2016). In this study, we show a possibility that strike-slip M>7 devastating earthquakes in this region have been gregion enerated by reactivation of transfer faults highly oblique to the rift axes. The 1948 Fukui earthquake (M7.1), onshore shallow seismic event with a strike-slip faulting mechanism (Kanamori, 1973), resulted in more than 3,500 causalities and destructive damages on the infrastructures. While geophysical analyses on geodetic measurements based on leveling and triangulation networks clearly show coseismic left-lateral fault slip on a NNW striking vertical fault plane beneath the Fukui plain (Sagiya, 1999), no evidence for coseismic surface rupture has been identified based on both post-earthquake intensive fieldwork and recent reexamination of stereopair interpretations using 1/3,000 aerial photographs taken in 1948 (Togo et al., 2000). To find recognizable fault-related structures that deform Neogene basin fill sediments, we collected new 9.6-km-long high-resolution seismic reflection data across the geodetically estimated fault plane and adjacent subparallel active strike slip faults, using 925 offline recorders and Envirovib truck as a seismic source. A depth-converted section to 1.5 km depth contains discontinuous seismic reflectors correlated to Miocene volcaniclastic deposits and depression of the overlying Plio-Pleistocene sediments above the geodetically determined fault plane. We interpreted

  11. FORMATION OF THE INITIAL DISTRIBUTION OF PLASMA COMPONENTS ON THE PHASE PLANE OF LARGE PARTICLES METHOD IN ELECTRIC ARC SYNTHESIS CNS

    Directory of Open Access Journals (Sweden)

    G. V. Abramov

    2014-01-01

    Full Text Available The article deals with the modeling of charged particles in a multicomponent plasma of electric arc discharge with binary collisions in the synthesis of carbon nanostructures (CNS. One of the common methods of obtaining the quality of fullerenes and nanotubes is arc synthesis under inert gas (helium. The determination of the necessary conditions and the mechanism of formation of carbon clusters in the plasma forming set CNS will more effectively and efficiently manage this process. Feature of the problem is that in a plasma arc discharge is a large number of particle interactions and on the cathode surface. Due to the high temperatures and high energy concentration in plasma detailed experimental investigation difficult to carry out. With the aim of avoiding difficult and costly physical experiments developed numerical methods for the analysis of plasma processes. In this article to solve a system of equations of Maxwell - Boltzmann basis for the authors had taken the method of large particles, which reduces the amount of computation and reduce the demands on computing resources. The authors cites the general design scheme of the large particles, and the algorithm of particle distribution of a multicomponent plasma in the phase plane at the initial time. In conclusion, the author argues that the results in the future will define the zone satisfies the energy conditions, the probability of formation of a plasma cluster groups of carbon involved in the synthesis of the CNS.

  12. Transferred plasma jet from a dielectric barrier discharge for processing of poly(dimethylsiloxane) surfaces

    CERN Document Server

    Nascimento, Fellype do; Canesqui, Mara A; Moshkalev, Stanislav

    2016-01-01

    In this work we studied processing of poly(dimethylsiloxane) (PDMS) surfaces using dielectric barrier discharge (DBD) plasma in two different assemblies, one using the primary plasma jet obtained from a conventional DBD and the other using a DBD plasma jet transfer. The evolution of water contact angle (WCA) in function of plasma processing time and in function of aging time as well as the changes in the surface roughness of PDMS samples for both plasma treatments have been studied. We also compared vibrational and rotational temperatures for both plasmas and for the first time the vibrational temperature (T_vib) for the transferred plasma jet has been shown to be higher as compared with the primary jet. The increment in the T_vib value seems to be the main reason for the improvements in adhesion properties and surface wettability for the transferred plasma jet. Possible explanations for the increase in the vibrational temperature are presented.

  13. Nonlinear Electromagnetic Waves and Spherical Arc-Polarized Waves in Space Plasmas

    Science.gov (United States)

    Tsurutani, B.; Ho, Christian M.; Arballo, John K.; Lakhina, Gurbax S.; Glassmeier, Karl-Heinz; Neubauer, Fritz M.

    1997-01-01

    We review observations of nonlinear plasma waves detected by interplanetary spacecraft. For this paper we will focus primarily on the phase-steepened properties of such waves. Plasma waves at comet Giacobini-Zinner measured by the International Cometary Explorer (ICE), at comets Halley and Grigg-Skjellerup measured by Giotto, and interplanetary Alfven waves measured by Ulysses, will be discussed and intercompared.

  14. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    DEFF Research Database (Denmark)

    Zhu, Jiajian; Gao, Jinlong; Ehn, Andreas

    2015-01-01

    , gives more realistic insight into the convection cooling process. Additionally, with the determination of the 3D slip velocity and the 3D length of the plasma column, we give more accurate estimates for the drag force, the electric field strength, the power per unit length, and the radius...... of the conducting zone of the plasma column. © 2015 AIP Publishing LLC....

  15. SEM study on the deposition of coal pyrolysis in arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Y.J.; Chen, H.G.; Yan, Y.L.; Lu, Y.K.; Li, F.; Xie, K.C. [Taiyuan University of Technology, Taiyuan (China). Shanxi Key Lab of Coal Science and Technology

    1999-07-01

    During coal pyrolysis in hydrogen plasma, residue was deposited on the reactor wall. Scanning electron microscopy indicated that metaplast were formed during the process. The mechanism of formation of deposits, their morphology, porosity and mechanical properties are discussed. It was shown that particles do not blend with plasma under these operation conditions. 4 refs., 5 figs., 2 tabs.

  16. Structural and Physical Characteristics of Ultrananocrystalline Diamond/Hydrogenated Amorphous Carbon Composite Films Deposited Using a Coaxial Arc Plasma Gun

    Science.gov (United States)

    Yoshitake, Tsuyoshi; Nakagawa, You; Nagano, Akira; Ohtani, Ryota; Setoyama, Hiroyuki; Kobayashi, Eiichi; Sumitani, Kazushi; Agawa, Yoshiaki; Nagayama, Kunihito

    2010-01-01

    Ultrananocrystalline diamond (UNCD)/hydrogenated amorphous carbon (a-C:H) films were formed without initial nucleation using a coaxial arc plasma gun. The UNCD crystallite diameters estimated from the X-ray diffraction peaks were approximately 2 nm. The Fourier transform infrared absorption spectrum exhibited an intense sp3-CH peak that might originate from the grain boundaries between UNCD crystallites whose dangling bonds are terminated with hydrogen atoms. A narrow sp3 peak in the photoemission spectrum implied that the film comprises a large number of UNCD crystallites. Large optical absorption coefficients at photon energies larger than 3 eV that might be due to the grain boundaries are specific to the UNCD/a-C:H films.

  17. Erosion behaviour of composite Al-Cr cathodes in cathodic arc plasmas in inert and reactive atmospheres

    CERN Document Server

    Franz, Robert; Hawranek, Gerhard; Polcik, Peter

    2015-01-01

    Al$_{x}$Cr$_{1-x}$ composite cathodes with Al contents of x = 0.75, 0.5 and 0.25 were exposed to cathodic arc plasmas in Ar, N$_2$ and O$_2$ atmospheres and their erosion behaviour was studied. Cross-sectional analysis of the elemental distribution of the near-surface zone in the cathodes by scanning electron microscopy revealed the formation of a modified layer for all cathodes and atmospheres. Due to intermixing of Al and Cr in the heat-affected zone, intermetallic Al-Cr phases formed as evidenced by X-ray diffraction analysis. Cathode poisoning effects in the reactive N$_2$ and O$_2$ atmospheres were non-uniform as a result of the applied magnetic field configuration. With the exception of oxide islands on Al-rich cathodes, reactive layers were absent in the circular erosion zone, while nitrides and oxides formed in the less eroded centre region of the cathodes.

  18. Photoelectron emission from metal surfaces induced by VUV-emission of filament driven hydrogen arc discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Laulainen, J.; Kalvas, T.; Koivisto, H.; Komppula, J.; Tarvainen, O. [University of Jyväskylä, Department of Physics (Finland)

    2015-04-08

    Photoelectron emission measurements have been performed using a filament-driven multi-cusp arc discharge volume production H{sup −} ion source (LIISA). It has been found that photoelectron currents obtained with Al, Cu, Mo, Ta and stainless steel (SAE 304) are on the same order of magnitude. The photoelectron currents depend linearly on the discharge power. It is shown experimentally that photoelectron emission is significant only in the short wavelength range of hydrogen spectrum due to the energy dependence of the quantum efficiency. It is estimated from the measured data that the maximum photoelectron flux from plasma chamber walls is on the order of 1 A per kW of discharge power.

  19. Transfer Matrix for Obliquely Incident Electromagnetic Waves Propagating in One Dimension Plasma Photonic Crystals

    Institute of Scientific and Technical Information of China (English)

    GUO Bin

    2009-01-01

    Based on the electromagnetic theory and by using an analytical technique-the transfer matrix method,the obliquely incident electromagnetic waves propagating in one-dimension plasma photonic crystals is studied.The dispersion relations for both the P-polarization waves and S-polarization waves,depending on the plasma density,plasma thickness and period,are discussed.

  20. New approaches for the reduction of plasma arc drop in second-generation thermionic converters. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hatziprokopiou, M.E.; Shaw, D.T.

    1981-03-31

    Investigations of ion generation and recombination mechanisms in the cesium plasma as they pertain to the advanced mode thermionic energy converter are described. The changes in plasma density and temperature within the converter have been studied under the influence of several promising auxiliary ionization candidate sources. Three novel approaches of external cesium ion generation have been investigated in some detail, namely vibrationally excited N/sub 2/ as an energy source of ionization of Cs ions in a DC discharge, microwave power as a means of resonant sustenance of the cesium plasma, and ion generation in a pulse N/sub 2/-Cs mixture. The experimental data obtained and discussed show that all three techniques - i.e. the non-LTE high-voltage pulsing, the energy transfer from vibrationally excited diatomic gases, and the external pumping with a microwave power - have considerable promise as schemes in auxiliary ion generation applicable to the advanced thermionic energy converter.

  1. A path for synthesis of boron-nitride nanostructures in volume of arc plasma

    Science.gov (United States)

    Han, Longtao; Krstić, Predrag

    2017-02-01

    We find a possible channel for direct nanosynthesis of boron-nitride (BN) nanostructures, including growth of BN nanotubes from a mixture of BN diatomic molecules by quantum-classical molecular dynamics simulations. No catalyst or boron nanoparticle is needed for this synthesis, however the conditions for the synthesis of each of the nanostructures, such as temperature and flux of the BN feedstock are identified and are compatible with the conditions in an electric arc at high pressure. We also find that BN nanostructures can be synthetized by feeding a boron nanoparticle by BN diatomic molecules, however if hydrogen rich molecules like NH3 or HBNH are used as a feedstock, two-dimensional nanoflake stable structures are formed.

  2. Momentum and energy dependent resolution function of the ARCS neutron chopper spectrometer at high momentum transfer: Comparing simulation and experiment

    Science.gov (United States)

    Diallo, S. O.; Lin, J. Y. Y.; Abernathy, D. L.; Azuah, R. T.

    2016-11-01

    Inelastic neutron scattering at high momentum transfers (i.e. Q ≥ 20 A ˚), commonly known as deep inelastic neutron scattering (DINS), provides direct observation of the momentum distribution of light atoms, making it a powerful probe for studying single-particle motions in liquids and solids. The quantitative analysis of DINS data requires an accurate knowledge of the instrument resolution function Ri(Q , E) at each momentum Q and energy transfer E, where the label i indicates whether the resolution was experimentally observed i = obs or simulated i=sim. Here, we describe two independent methods for determining the total resolution function Ri(Q , E) of the ARCS neutron instrument at the Spallation Neutron Source, Oak Ridge National Laboratory. The first method uses experimental data from an archetypical system (liquid 4He) studied with DINS, which are then numerically deconvoluted using its previously determined intrinsic scattering function to yield Robs(Q , E). The second approach uses accurate Monte Carlo simulations of the ARCS spectrometer, which account for all instrument contributions, coupled to a representative scattering kernel to reproduce the experimentally observed response S(Q , E). Using a delta function as scattering kernel, the simulation yields a resolution function Rsim(Q , E) with comparable lineshape and features as Robs(Q , E), but somewhat narrower due to the ideal nature of the model. Using each of these two Ri(Q , E) separately, we extract characteristic parameters of liquid 4He such as the intrinsic linewidth α2 (which sets the atomic kinetic energy ∼α2) in the normal liquid and the Bose-Einstein condensate parameter n0 in the superfluid phase. The extracted α2 values agree well with previous measurements at saturated vapor pressure (SVP) as well as at elevated pressure (24 bars) within experimental precision, independent of which Ri(Q , y) is used to analyze the data. The actual observed n0 values at each Q vary little with the

  3. A plasma membrane-targeted cytosolic domain of STIM1 selectively activates ARC channels, an arachidonate-regulated store-independent Orai channel.

    Science.gov (United States)

    Thompson, Jill L; Shuttleworth, Trevor J

    2012-01-01

    The Orai family of calcium channels includes the store-operated CRAC channels and store-independent, arachidonic acid (AA)-regulated ARC channels. Both depend on STIM1 for their activation but, whereas CRAC channel activation involves sensing the depletion of intracellular calcium stores via a luminal N terminal EF-hand of STIM1 in the endoplasmic reticulum (ER) membrane, ARC channels are exclusively activated by the pool of STIM1 that constitutively resides in the plasma membrane (PM). Here, the EF-hand is extracellular and unlikely to ever lose its bound calcium, suggesting that STIM1-dependent activation of ARC channels is very different from that of CRAC channels. We now show that attachment of the cytosolic portion of STIM1 to the inner face of the PM via an N terminal Lck-domain sequence is sufficient to enable normal AA-dependent activation of ARC channels, while failing to allow activation of store-operated CRAC channels. Introduction of a point mutation within the Lck-domain resulted in the loss of both PM localization and ARC channel activation. Reversing the orientation of the PM-anchored STIM1 C terminus via a C-terminal CAAX-box fails to support either CRAC or ARC channel activation. Finally, the Lck-anchored STIM1 C-terminal domain also enabled the exclusive activation of the ARC channels following physiological agonist addition. These data demonstrate that simple tethering of the cytosolic C-terminal domain of STIM1 to the inner face of the PM is sufficient to allow the full, normal and exclusive activation of ARC channels, and that the N-terminal regions of STIM1 (including the EF-hand domain) play no significant role in this activation.

  4. Decomposition of CCl4 and CHCl3 on gliding arc plasma

    Institute of Scientific and Technical Information of China (English)

    Antonius Indarto; CHOI Jae-wook; LEE Hwaung; SONG Hyung-keun

    2006-01-01

    Decomposition of chlorinated hydrocarbons, CCl4 and CHCl3, in gliding plasma was examined. The effects of initial concentrations, total gas flow rates, and power consumption have been investigated. The conversion result was relatively high. It reached 80% for CCl4 and 97% for CHCl3. Using atmospheric air as the carrier gas, the plasma reaction occurred at exothermic reaction and the main products were CO2, CO, and Cl2. Transformation into CCl4 was also detected for CHCl3 decomposition reaction.The conversion of CCl4 and CHCl3 were increased with the increasing applied frequency and decreasing total gas flow rate.

  5. Investigation of micro-structure and micro-hardness properties of 304L stainless steel treated in a hot cathode arc discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Malik, Hitendra K., E-mail: hkmalik@physics.iitd.ac.in [Department of Physics, Indian Institute of Technology Delhi, New Delhi – 110016 (India); Singh, Omveer [Centre for Energy Studies, Indian Institute of Technology Delhi, New Delhi – 110016 (India); Dahiya, Raj P. [Centre for Energy Studies, Indian Institute of Technology Delhi, New Delhi – 110016 (India); Deenbandhu Chhotu Ram University of Science and Technology, Murthal–131039 (India)

    2015-08-28

    We have established a hot cathode arc discharge plasma system, where different stainless steel samples can be treated by monitoring the plasma parameters and nitriding parameters independently. In the present work, a mixture of 70% N{sub 2} and 30% H{sub 2} gases was fed into the plasma chamber and the treatment time and substrate temperature were optimized for treating 304L Stainless Steel samples. Various physical techniques such as x-ray diffraction, energy dispersive x-ray spectroscopy and micro-vickers hardness tester were employed to determine the structural, surface composition and surface hardness of the treated samples.

  6. Investigation of micro-structure and micro-hardness properties of 304L stainless steel treated in a hot cathode arc discharge plasma

    Science.gov (United States)

    Malik, Hitendra K.; Singh, Omveer; Dahiya, Raj P.

    2015-08-01

    We have established a hot cathode arc discharge plasma system, where different stainless steel samples can be treated by monitoring the plasma parameters and nitriding parameters independently. In the present work, a mixture of 70% N2 and 30% H2 gases was fed into the plasma chamber and the treatment time and substrate temperature were optimized for treating 304L Stainless Steel samples. Various physical techniques such as x-ray diffraction, energy dispersive x-ray spectroscopy and micro-vickers hardness tester were employed to determine the structural, surface composition and surface hardness of the treated samples.

  7. Transfer of microwave energy along a filament plasma column in air

    Science.gov (United States)

    Prade, B.; Houard, A.; Larour, J.; Pellet, M.; Mysyrowicz, A.

    2017-01-01

    We demonstrate the coupling of microwave radiation into a plasma channel formed by laser filamentation in air, leading to the amplification by two orders of magnitude of longitudinal oscillations of the plasma. Transfer of this longitudinal excitation toward unexcited region of the plasma column occurs over >10 cm, in good agreement with a theoretical model describing the propagation of a TM wave guided along the surface between air and plasma. We foresee that high-power low-frequency electromagnetic waves injected into a multi-filament plasma could initiate and sustain a long-lived plasma over several meters distance.

  8. Plasma-MIG hybrid arc welding with PID increment constant current or voltage control algorithm%增量型PID恒流恒压控制的Plasma-MIG复合电弧焊接

    Institute of Scientific and Technical Information of China (English)

    杨涛; 张生虎; 高洪明; 吴林; 许可望; 刘永贞

    2013-01-01

    Plasma-MIG复合电弧焊接对电源的外特性输出及焊接过程控制有着很高的要求,以VC++软件开发工具为平台,推导了适合于Plasma-MIG复合电弧焊接的增量型PID控制算法,实现了对复合电弧焊接过程控制及电源外特性的要求.结果表明,增量型PID恒流恒压控制能够满足Plasma-MIG对电源外特性的输出要求.Plasma电弧和MIG电弧并不是相互独立的,两者以共享的电磁空间、导电气氛和焊丝为媒介建立起耦合关系.Plasma-MIG复合电弧焊接过程中,增量型PID控制下的Plasma电弧能够自发的调节自身电参数,来稳定电弧空间的电流密度,使得焊接过程中无飞溅.采用控制后,Plasma-MIG复合电弧焊焊接过程焊缝铺展好,焊接过程稳定,焊缝成形好.%Output characteristics of the power supply and welding process control are important factors for plasma-MIG hybrid arc welding. PID increment control algorithm suitable for Plasma-MIG hybrid arc welding was developed based on VC + + language in this paper, which optimized the output characteristics of the power supply and welding process control. The results show that the plasma arc and MIG arc were coupled with each other by sharing the electro-magnetic space, gas and filler metal. Plasma are controlled by PID increment control algorithm was capable of stabilizing the current density through the arc due to its self-adjusting function, without sputtering in the welding process. High stability, molten metal with excellent liquidity and weld with smooth surface were realized by plasma-MIG hybrid arc welding with PID increment control algorithm.

  9. Inorganic-solid-state electrolyte layer deposited by cathodic arc plasma for rapidly switching electrochromic device

    Science.gov (United States)

    Chen, Po-Wen; Chang, Chen-Te; Wu, Jin-Yu; Jan, Der-Jun; Li, Yu-Chen; Hsieh, Cheng-Chang; Tsai, Wen-Fa

    2017-08-01

    This work focuses on fabricating a solid electrolyte Ta2O5 thin film deposited by cathodic arc plasm (CAP) deposition through three different ratio of oxygen and argon. In our experiments, refractive index of Ta2O5 films are taken as 2.25, 1.96, 1.9 with various O2/Ar= 1.5, O2/Ar= 2, O2/Ar= 2.4, respectively. Our results show that the refractive index mostly decreased as we increase the oxygen flow rate, in which the minimum is found at 240 sccm. It provides good conduction pathways for ions through smaller thin-film's refractive index that exhibits more porosity voids. This property enhances ion's mobility for electrochromic device causing rapid coloring/bleaching phenomenon. Ta2O5 thin film is suitable as a solid electrolyte layer in center of electrochromic device (ECD) using CAP deposition. As a result, rapid response times were observed in fabricated device with an area of 5 cm×5 cm, exhibiting transmittance optical modulation ΔT = 61.5% (@550 nm) with the bleaching time τ = 8 s and transmittance optical modulation ΔT = 50% (@550 nm) with the coloring time τ = 10 s.

  10. The role of cholesteryl ester transfer protein and phospholipid transfer protein in the remodeling of plasma high-density lipoproteins.

    Science.gov (United States)

    Lagrost, L

    1997-08-01

    Recent studies demonstrated that alterations in the size distribution of high-density lipoproteins (HDLs) constitute reliable markers for the risk of coronary artery disease. These observations suggested that the determination of the size distribution of HDL subpopulations by using polyacrylamide gradient gel electrophoresis might constitute an effective tool in clinical practice for the detection of patients with elevated risk. During the last decade, concordant observations revealed that all the HDL subpopulations are metabolically interrelated, and their relative abundances are dependent on the activity of several plasma factors, among them the cholesteryl ester transfer protein (CETP) and the phospholipid transfer protein (PLTP). As reviewed in the present article, although both CETP and PLTP can promote the size redistribution or conversion of HDL, the two plasma lipid transfer proteins can alter differently the plasma HDL distribution profile through distinct mechanisms. (Trends Cardiovasc Med 1997;7:218-224). © 1997, Elsevier Science Inc.

  11. Infrared fingerprints and periodic formation of nanoparticles in Ar/C2H2 plasmas

    Science.gov (United States)

    Kovačević, Eva; Stefanović, Ilija; Berndt, Johannes; Winter, Jörg

    2003-03-01

    The formation of dust particles in argon diluted C2H2 plasmas was studied by means of Fourier transform infrared absorption spectroscopy and mass spectroscopy. The detection limit for infrared absorption was significantly improved by the use of a multipass technique. Measuring the intensity of the Rayleigh/Mie scattering of the infrared signal we found a periodicity of dust formation/vanishing (period of about 35 min in our experimental conditions). The fast disappearance of the dust from the plasma region at the end of every period is the evidence of a narrow particle size distribution, as confirmed by secondary electron micrographs of the collected powder. Characteristic infrared absorption features have their origin in absorption within the dust particles. Besides the strong presence of aliphatic hydrocarbons characteristic for amorphous hydrocarbon films, a significant amount of aromatic structures was detected. Heavy positive ions measured by ion-mass spectroscopy originate from polyacetilenic (C2nH2) and aromatic compounds. Time resolved mass spectra gave insight into the plasma response to the dust formation.

  12. Destruction of inorganic municipal solid waste incinerator fly ash in a DC arc plasma furnace.

    Science.gov (United States)

    Zhao, Peng; Ni, Guohua; Jiang, Yiman; Chen, Longwei; Chen, Mingzhou; Meng, Yuedong

    2010-09-15

    Due to the toxicity of dioxins, furans and heavy metals, there is a growing environmental concern on municipal solid waste incinerator (MSWI) fly ash in China. The purpose of this study is directed towards the volume-reduction of fly ash without any additive by thermal plasma and recycling of vitrified slag. This process uses extremely high-temperature in an oxygen-starved environment to completely decompose complex waste into very simple molecules. For developing the proper plasma processes to treat MSWI fly ash, a new crucible-type plasma furnace was built. The melting process metamorphosed fly ash to granulated slag that was less than 1/3 of the volume of the fly ash, and about 64% of the weight of the fly ash. The safety of the vitrified slag was tested. The properties of the slag were affected by the differences in the cooling methods. Water-cooled and composite-cooled slag showed more excellent resistance against the leaching of heavy metals and can be utilized as building material without toxicity problems.

  13. Unification of Anion Relay Chemistry (ARC) with the Takeda and Hiyama Cross-Coupling Reactions: Identification of an Effective Silicon-Based Transfer Agent

    OpenAIRE

    Smith, Amos B.; Hoye, Adam T.; Martinez-Solorio, Dionicio; Kim, Won-Suk; Tong, Rongbiao

    2012-01-01

    The unification of Anion Relay Chemistry (ARC) with the Takeda and Hiyama palladium-mediated cross-coupling processes to provide aryl-aryl, alkenyl-aryl and alkenyl-alkenyl coupling products, exploiting a common silicon-based transfer agent, has been achieved. These results provide a practical solution to the intermolecular cross-coupling of organolithium reagents without problematic lithium-halogen exchange and/or undesired homocoupling that has kept organolithium cross-couplings from achiev...

  14. Elevation of plasma phospholipid transfer protein increases the risk of atherosclerosis despite lower apolipoprotein B-containing lipoproteins.

    NARCIS (Netherlands)

    J. Lie (Jessica); M.P.G. de Crom (Rini); T. van Gent (Teus); M.J. van Haperen (Rien); L. Scheek (Leo); F. Sadeghi-Niaraki (Farah); A. van Tol (Arie)

    2004-01-01

    textabstractPlasma phospholipid transfer protein (PLTP) transfers phospholipids between lipoproteins and mediates HDL conversion. PLTP-overexpressing mice have increased atherosclerosis. However, mice do not express cholesteryl ester transfer protein (CETP), which is involved in

  15. Type 2 diabetes mellitus is associated with differential effects on plasma cholesteryl ester transfer protein and phospholipid transfer protein activities and concentrations

    NARCIS (Netherlands)

    Dullaart, RPF; De Vries, R; Scheek, L; Borggreve, SE; Van Gent, T; Dallinga-Thie, GM; Ito, M; Nagano, M; Sluiter, WJ; Hattori, H; Van Tol, A

    2004-01-01

    Background: Human plasma contains two lipid transfer proteins, cholesteryl ester transfer protein (CETP) and phospholipid transfer protein (PLTP), which are crucial in reverse cholesterol transport. Methods: Plasma CETP and PLTP activity levels and concentrations in 16 type 2 diabetic patients and 1

  16. Effect of pulsed current micro plasma arc welding process parameters on fusion zone grain size and ultimate tensile strength of Inconel 625 sheets

    Institute of Scientific and Technical Information of China (English)

    Kondapalli Siva Prasad; Chalamalasetti Srinivasa Rao; Damera Nageswara Rao

    2012-01-01

    The paper focuses on developing mathematical models to predict grain size and ultimate tensile strength of pulsed current micro plasma arc welded Inconel 625 nickel alloy.Four factors,five levels,central composite rotatable design matrix is used to optimize the number of experiments.The mathematical models have been developed by response surface method.The adequacy of the models is checked by analysis of variance technique.By using the developed mathematical models,grain size and ultimate tensile strength of the joints can be predicted with 99%0 confidence level.Contour plots are drawn to study the interaction effect of pulsed current micro plasma arc welding parameters on fusion zone grain size and ultimate tensile strength of Inconel 625 weld ioints.

  17. Simulation of the atomic and ionic densities in the ionization layer of a plasma arc with a binary cathode

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, D; Marin, J A Sillero; Munoz-Serrano, E; Casado, E, E-mail: f92orhed@uco.e [Departamento de Fisica, Universidad de Cordoba, 14071 Cordoba (Spain)

    2009-04-21

    A physical model was developed to study the behaviour of the cathode material evaporated from a thoriated tungsten cathode of an atmospheric-pressure argon plasma arc. The densities of tungsten and thorium atoms and ions in the ionization layer were obtained, and the influence of the different physical processes on the evaporated cathode material was established. It was found that almost all of the neutral atoms evaporated from the cathode are ionized near the beginning of the ionization layer, i.e. near the boundary between the sheath and the ionization layer. Thorium ions are concentrated in a 4 {mu}m region near the beginning of this layer, while tungsten ions are found in a region of 9 {mu}m. The contribution of the electric force to the velocity of ions is the dominant contribution only near the beginning of the ionization layer. At a distance from the interface between the sheath and the ionization layer greater than 3.8 {mu}m in the case of thorium ions, and greater than 5 {mu}m in the case of tungsten ions, the contributions of the density gradient forces and the frictional forces are more important than the electric force contribution.

  18. Electron Density and Temperature Measurement by Stark Broadening in a Cold Argon Arc-Plasma Jet at Atmospheric Pressure

    Institute of Scientific and Technical Information of China (English)

    ZHOU Qiuping; CHENG Cheng; MENG Yuedong

    2009-01-01

    Determination of both the electron density and temperature simultaneously in a cold argon arc-plasma jet by analyzing the Stark broadening of two different emission lines is presented.This method is based on the fact that the Stark broadening of different lines has a different dependence on the electron density and temperature.Therefore,a comparison of two or more line broadenings allows us to diagnose the electron density and temperature simultaneously.In this study we used the first two Balmer series hydrogen lines H_α and H_β for their large broadening width.For this purpose,a small amount of hydrogen was introduced into the discharge gas.The results of the Gigosos-Cardenoso computational model,considering more relevant processes for the hydrogen Balmer lines,is used to process the experimental data.With this method,we obtained reliable electron density and temperature,1.88 ×10 ~(15) cm~(-3 )and 13000 K,respectively.Possible sources of error were also analyzed.

  19. Erosion behavior of composite Al-Cr cathodes in cathodic arc plasmas in inert and reactive atmospheres

    Energy Technology Data Exchange (ETDEWEB)

    Franz, Robert, E-mail: robert.franz@unileoben.ac.at; Mendez Martin, Francisca; Hawranek, Gerhard [Montanuniversität Leoben, Franz-Josef-Strasse 18, 8700 Leoben (Austria); Polcik, Peter [Plansee Composite Materials GmbH, Siebenbürgerstrasse 23, 86983 Lechbruck am See (Germany)

    2016-03-15

    Al{sub x}Cr{sub 1−x} composite cathodes with Al contents of x = 0.75, 0.5, and 0.25 were exposed to cathodic arc plasmas in Ar, N{sub 2}, and O{sub 2} atmospheres and their erosion behavior was studied. Cross-sectional analysis of the elemental distribution of the near-surface zone in the cathodes by scanning electron microscopy revealed the formation of a modified layer for all cathodes and atmospheres. Due to intermixing of Al and Cr in the heat-affected zone, intermetallic Al-Cr phases formed as evidenced by x-ray diffraction analysis. Cathode poisoning effects in the reactive N{sub 2} and O{sub 2} atmospheres were nonuniform as a result of the applied magnetic field configuration. With the exception of oxide islands on Al-rich cathodes, reactive layers were absent in the circular erosion zone, while nitrides and oxides formed in the less eroded center region of the cathodes.

  20. Electric-probe Diagnostics for Plasma Configuration of Large-scale Magnetically Dispersed Arc Plasma%大尺度磁分散电弧等离子体位形的静电探针诊断

    Institute of Scientific and Technical Information of China (English)

    查俊; 焦凌云; 白冰; 王城; 夏维东

    2013-01-01

    磁旋转电弧可以产生大面积均匀等离子体:磁分散电弧等离子体.利用快速移动水冷静电探针对大气压氩弧磁分散电弧等离子体进行了诊断,得到发生器弧室内的电子温度分布、电弧位形以及等离子体波动等信息.诊断结果表明:等离子体弧柱区呈圆盘状,并在轴向有较大扩张,弧柱区下游等离子体波动较大,为等离子体云与冷气团混合所致.将探针诊断结果与采用热力学平衡模型的数值计算结果比较,发现2者具有相似的等离子体位形,但实验测量得到的电子温度更高,等离子体分布范围更广.分析认为,这种差异可能是等离子体偏离局域热力学平衡和等离子体的不稳定性造成的.%Magnetically rotating arc can induce large-scale magnetically dispersed arc plasma.Using a fast-moving water-cooling electric probe,we diagnosed large-scale dispersed arc plasma in argon at atmospheric pressure,and obtained its electron temperature profile,arc plasma configuration and plasma fluctuation.It is shown that the arc column exhibits a disk configuration and expands in axial direction.In the meantime,the erratic fluctuation increases in the plasma downstream,which may be a result of the cold air entrainment in the plasma cloud.There is a good comparability in plasma configuration between the measurements and the simulations by local-thermedynamicequilibrium magneto-hydrodynamic model,while the measurements have relatively higher electron temperature and larger plasma volume phenomenon.Further analysis indicates that the difference may be caused by deviation from thermal equilibrium of plasma and instability of plasma.

  1. The formation mechanism of CO{sub 2} and its conversion in the process of coal gasification under arc plasma conditions

    Energy Technology Data Exchange (ETDEWEB)

    He, X.J.; Zheng, M.D.; Qiu, J.S.; Zhao, Z.B.; Ma, T.C. [Dalian University of Technology, Dalian (China). Carbon Research Laboratory

    2006-05-15

    The carbon dioxide (CO{sub 2}) formation mechanism and co-conversion of CO{sub 2} with coal was investigated in the process of coal gasification in a steam medium at atmospheric pressure under arc plasma conditions in a tube-type setup. The arc plasma was diagnosed in situ by optical emission spectroscopy and the gas products were analysed by gas chromatography. CO{sub 2} yields are correlated with the quantitative emission peak intensity of the active species in plasma when the operating parameter is changed. The results show that the greater the emission peak intensity of the CH radicals, C2 radicals, OH radicals or O atoms, the smaller the CO{sub 2} yield is, which means that the CO{sub 2} formation process is inhibited by increasing the concentration of the mentioned active species under arc plasma conditions. On the basis of the diagnosis results, co-conversion of CO{sub 2} and coal in a steam medium under plasma conditions was carried out in the same setup and the results show that CO{sub 2} conversion reaches 88.6% while the concentration of CO + H{sub 2} reaches 87.4%; at the same time, coal conversion is in the range 54.7 - 68.7%, which proves that co-conversion of CO{sub 2} and coal in a steam medium under plasma conditions might be a prospective way to utilize CO{sub 2} and the production of synthesis gas.

  2. The formation mechanism of CO{sub 2} and its conversion in the process of coal gasification under arc plasma conditions

    Energy Technology Data Exchange (ETDEWEB)

    He Xiaojun [School of Chemistry and Chemical Engineering, Anhui University of Technology, 59 Hudong Road, Maanshan 243002 (China); Zheng Mingdong [School of Chemistry and Chemical Engineering, Anhui University of Technology, 59 Hudong Road, Maanshan 243002 (China); Qiu Jieshan [Carbon Research Laboratory, School of Chemical Engineering, State Key Lab of Fine Chemical, Dalian University of Technology, 158 Zhongshan Road, Dalian 116012 (China); Zhao Zongbin [Carbon Research Laboratory, School of Chemical Engineering, State Key Lab of Fine Chemical, Dalian University of Technology, 158 Zhongshan Road, Dalian 116012 (China); Ma Tengcai [State Key Lab for Material Modification by Laser, Ion and Electron Beams, Dalian University of Technology, Dalian 116023 (China)

    2006-05-15

    The carbon dioxide (CO{sub 2}) formation mechanism and co-conversion of CO{sub 2} with coal was investigated in the process of coal gasification in a steam medium at atmospheric pressure under arc plasma conditions in a tube-type setup. The arc plasma was diagnosed in situ by optical emission spectroscopy and the gas products were analysed by gas chromatography. CO{sub 2} yields are correlated with the quantitative emission peak intensity of the active species in plasma when the operating parameter is changed. The results show that the greater the emission peak intensity of the CH radicals, C{sub 2} radicals, OH radicals or O atoms, the smaller the CO{sub 2} yield is, which means that the CO{sub 2} formation process is inhibited by increasing the concentration of the mentioned active species under arc plasma conditions. On the basis of the diagnosis results, co-conversion of CO{sub 2} and coal in a steam medium under plasma conditions was carried out in the same setup and the results show that CO{sub 2} conversion reaches 88.6% while the concentration of CO + H{sub 2} reaches 87.4%; at the same time, coal conversion is in the range 54.7-68.7%, which proves that co-conversion of CO{sub 2} and coal in a steam medium under plasma conditions might be a prospective way to utilize CO{sub 2} and the production of synthesis gas.

  3. Deposition of duplex Al 2O 3/aluminum coatings on steel using a combined technique of arc spraying and plasma electrolytic oxidation

    Science.gov (United States)

    Gu, Weichao; Shen, Dejiu; Wang, Yulin; Chen, Guangliang; Feng, Wenran; Zhang, Guling; Fan, Songhua; Liu, Chizi; Yang, Size

    2006-02-01

    Plasma electrolytic oxidation (PEO) is a cost-effective technique that can be used to prepare ceramic coatings on metals such as Ti, Al, Mg, Nb, etc., and their alloys, but this promising technique cannot be used to modify the surface properties of steels, which are the most widely used materials in engineering. In order to prepare metallurgically bonded ceramic coatings on steels, a combined technique of arc spraying and plasma electrolytic oxidation (PEO) was adopted. In this work, metallurgically bonded ceramic coatings on steels were obtained using this method. We firstly prepared aluminum coatings on steels by arc spraying, and then obtained the metallurgically bonded ceramic coatings on aluminum coatings by PEO. The characteristics of duplex coatings were analyzed by X-ray diffractometer (XRD) and scanning electron microscopy (SEM). The corrosion and wear resistance of the ceramic coatings were also studied. The results show that, duplex Al 2O 3/aluminum coatings have been deposited on steel substrate after the combined treatment. The ceramic coatings are mainly composed of α-Al 2O 3, γ-Al 2O 3, θ-Al 2O 3 and some amorphous phase. The duplex coatings show favorable corrosion and wear resistance properties. The investigations indicate that the combination of arc spraying and plasma electrolytic oxidation proves a promising technique for surface modification of steels for protective purposes.

  4. Computation of laminar heat transfer from gaseous plasmas in electromagnetic fields

    Science.gov (United States)

    Bose, T. K.

    1972-01-01

    Heat transfer analysis procedure is presented for two-temperature gaseous plasma. Analysis is based on laminar flow of singly-ionized, quasineutral plasma with variable properties. Sheath analysis is described for species in accelerating field, decelerating field, emitted from wall, and recombining at wall.

  5. Formation of HCN and NH{sub 3} during Datong coal pyrolysis in arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Bao Wei-ren; Zhang Jin-cao; Shen Shu-guang; Cao Qing; Lu Yong-kang [Taiyuan University of Technology, Taiyuan (China). Key Laboratory of Coal Science and Technology

    2006-07-01

    The formation of HCN and NH{sub 3} from coal-N was investigated in a plasma coal pyrolysis reactor. Based on Gibbs free energy minimization principle, Thermodynamic equilibrium fraction of C-H-O-N was calculated. The results from experiments and calculation suggest that HCN is the main product of coal-N at high temperature. Only a little coal-N convertedto NH{sub 3}. As the temperature increases, the yields of HCN and NH{sub 3} increases from the experimental results, but the theoretic calculated results show that HCN gradually increases and NH{sub 3} decreases. The possible reason is the influence of practical operating condition. The yield of HCN increases firstly and then decreases with increasing coal feeding rate, but NH{sub 3} is reverse. Enhancement of input power lease to the increase of HCN and NH{sub 3} yields. H{sub 2} acting as the reactive atmosphere benefits to the formation of HCN and NH{sub 3}, and CO{sub 2} may reduce the yields of HCN and NH{sub 3}, O{sub 2} enhance the formation of NH{sub 3}, but promotes the furthermore conversion of HCN. 12 refs., 4 figs., 1 tab.

  6. Pulsed Current Gas Metal Arc Welding under Different Shielding and Pulse Parameters; Part 2: Behaviour of Metal Transfer

    National Research Council Canada - National Science Library

    Ghosh, P. K; Dorn, Lutz; Devakumaran, K; Hofmann, F

    2009-01-01

    ...) of pulsed current gas metal arc welding (P-GMAW) using mild steel filler wire have been studied with respect to change in pulse parameters under different gas shieldings of Ar+2%CO2 and Ar+18%CO2...

  7. Influence of Mode of Metal Transfer on Microstructure and Mechanical Properties of Gas Metal Arc-Welded Modified Ferritic Stainless Steel

    Science.gov (United States)

    Mukherjee, Manidipto; Pal, Tapan Kumar

    2012-06-01

    This article describes in detail the effect of the modes of metal transfer on the microstructure and mechanical properties of gas metal arc-welded modified ferritic stainless steel (SSP 409M) sheets (as received) of 4 mm thickness. The welded joints were prepared under three modes of metal transfer, i.e., short-circuit (SC), spray (S), transfer, and mix (M) mode transfer using two different austenitic filler wires (308L and 316L) and shielding gas composition of Ar + 5 pct CO2. The welded joints were evaluated by means of microstructural, hardness, notched tensile strength, Charpy impact toughness, and high cycle fatigue. The dependence of weld metal microstructure on modes of metal transfer and filler wires has been determined by dilution calculation, WRC-1992 diagram, Creq/Nieq ratio, stacking fault energy (SFE), optical microscopy (OM), and transmission electron microscopy (TEM). It was observed that the microstructure as well as the tensile, Charpy impact, and high cycle fatigue of weld metal is significantly affected by the mode of metal transfer and filler wire used. However, the heat-affected zone (HAZ) is affected only by the modes of metal transfer. The results have been correlated with the microstructures of weld and HAZ developed under different modes of metal transfer.

  8. [Arc spectrum diagnostic and heat coupling mechanism analysis of double wire pulsed MIG welding].

    Science.gov (United States)

    Liu, Yong-qiang; Li, Huan; Yang, Li-jun; Zheng, Kai; Gao, Ying

    2015-01-01

    A double wire pulsed MIG welding test system was built in the present paper, in order to analyze the heat-coupling mechanism of double wire pulsed MIG welding, and study are temperature field. Spectroscopic technique was used in diagnostic analysis of the are, plasma radiation was collected by using hollow probe method to obtain the arc plasma optical signal The electron temperature of double wire pulsed MIG welding arc plasma was calculated by using Boltzmann diagram method, the electron temperature distribution was obtained, a comprehensive analysis of the arc was conducted combined with the high speed camera technology and acquisition means of electricity signal. The innovation of this paper is the combination of high-speed camera image information of are and optical signal of arc plasma to analyze the coupling mechanism for dual arc, and a more intuitive analysis for are temperature field was conducted. The test results showed that a push-pull output was achieved and droplet transfer mode was a drop in a pulse in the welding process; Two arcs attracted each other under the action of a magnetic field, and shifted to the center of the arc in welding process, so a new heat center was formed at the geometric center of the double arc, and flowing up phenomenon occurred on the arc; Dual arc electronic temperature showed an inverted V-shaped distribution overall, and at the geometric center of the double arc, the arc electron temperature at 3 mm off the workpiece surface was the highest, which was 16,887.66 K, about 4,900 K higher than the lowest temperature 11,963.63 K.

  9. Hydrogen storage and hydrolysis properties of core-shell structured Mg-MFx (M=V, Ni, La and Ce) nano-composites prepared by arc plasma method

    Science.gov (United States)

    Mao, Jianfeng; Zou, Jianxin; Lu, Chong; Zeng, Xiaoqin; Ding, Wenjiang

    2017-10-01

    In this work, core-shell structured Mg-MFx (M = V, Ni, La and Ce) nano-composites are prepared by using arc plasma method. The particle size distribution, phase components, microstructures, hydrogen sorption properties of these composites and hydrolysis properties of their corresponding hydrogenated powders are carefully investigated. It is shown that the addition of MFx through arc plasma method can improve both the hydrogen absorption kinetics of Mg and the hydrolysis properties of corresponding hydrogenated powders. Among them, the Mg-NiF2 composite shows the best hydrogen absorption properties at relatively low temperatures, which can absorb 3.26 wt% of H2 at 373 K in 2 h. Such rapid hydrogen absorption rate is mainly due to the formation of Mg2Ni and MgF2 on Mg particles during arc evaporation and condensation. In contrast, measurements also show that the hydrogenated Mg-VF3 composite has the lowest peak desorption temperature and the fastest hydrolysis rate among all the hydrogenated Mg-MFx composites. The less agglomeration tendency of Mg particles and VO2 covered on MgH2 particles account for the reduced hydrogen desorption temperature and enhanced hydrolysis rate.

  10. Arc Interference Behavior during Twin Wire Gas Metal Arc Welding Process

    Directory of Open Access Journals (Sweden)

    Dingjian Ye

    2013-01-01

    Full Text Available In order to study arc interference behavior during twin wire gas metal arc welding process, the synchronous acquisition system has been established to acquire instantaneous information of arc profile including dynamic arc length variation as well as relative voltage and current signals. The results show that after trailing arc (T-arc is added to the middle arc (M-arc in a stable welding process, the current of M arc remains unchanged while the agitation increases; the voltage of M arc has an obvious increase; the shape of M arc changes, with increasing width, length, and area; the transfer frequency of M arc droplet increases and the droplet itself becomes smaller. The wire extension length of twin arc turns out to be shorter than that of single arc welding.

  11. Mass transfer in the lower crust: Evidence for incipient melt assisted flow along grain boundaries in the deep arc granulites of Fiordland, New Zealand

    Science.gov (United States)

    Stuart, Catherine A.; Piazolo, Sandra; Daczko, Nathan R.

    2016-09-01

    Knowledge of mass transfer is critical in improving our understanding of crustal evolution, however mass transfer mechanisms are debated, especially in arc environments. The Pembroke Granulite is a gabbroic gneiss, passively exhumed from depths of >45 km from the arc root of Fiordland, New Zealand. Here, enstatite and diopside grains are replaced by coronas of pargasite and quartz, which may be asymmetric, recording hydration of the gabbroic gneiss. The coronas contain microstructures indicative of the former presence of melt, supported by pseudosection modeling consistent with the reaction having occurred near the solidus of the rock (630-710°C, 8.8-12.4 kbar). Homogeneous mineral chemistry in reaction products indicates an open system, despite limited metasomatism at the hand sample scale. We propose the partial replacement microstructures are a result of a reaction involving an externally derived hydrous, silicate melt and the relatively anhydrous, high-grade assemblage. Trace element mapping reveals a correlation between reaction microstructure development and bands of high-Sr plagioclase, recording pathways of the reactant melt along grain boundaries. Replacement microstructures record pathways of diffuse porous melt flow at a kilometer scale within the lower crust, which was assisted by small proportions of incipient melt providing a permeable network. This work recognizes melt flux through the lower crust in the absence of significant metasomatism, which may be more common than is currently recognized. As similar microstructures are found elsewhere within the exposed Fiordland lower crustal arc rocks, mass transfer of melt by diffuse porous flow may have fluxed an area >10,000 km2.

  12. Experimental analysis of DBD plasma jet properties using different gases and two kinds of transfer plate

    CERN Document Server

    Nascimento, Fellype do; Machida, Munemasa

    2015-01-01

    Dielectric Barrier Discharge (DBD) plasma jets has been studied extensively in recent years because of its wide range of applications. DBD plasmas can be produced using many different gases and can be applied to a broad variety of surfaces and substrates. In this work, we provide a comparison of DBD plasmas generated using argon (Ar), helium (He) and nitrogen (N2), as well as their mixtures with water vapor in order to know how some plasma properties are affected by the use of different gases. All plasmas were studied in two different conditions, using a transfer plate made of a conductive material and using a transfer plate made of an insulating one. We observed that the processes of excitation and ionization of nitrogen molecules by direct collisions with Ar or He are more evident and significant in He plasmas, which means that He atoms in metastable states have greater ability to transfer energy to molecules of nitrogen in the plasma. The collisions of He atoms in metastable states with N2 molecules determ...

  13. Optimization of magnetocaloric properties of arc-melted and spark plasma-sintered LaFe{sub 11.6}Si{sub 1.4}

    Energy Technology Data Exchange (ETDEWEB)

    Shamba, P.; Morley, N.A.; Reaney, I.M.; Rainforth, W.M. [University of Sheffield, Department of Materials Science and Engineering, Sheffield (United Kingdom); Cespedes, O. [University of Leeds, School of Physics and Astronomy, Leeds (United Kingdom)

    2016-08-15

    LaFe{sub 11.6}Si{sub 1.4} alloy has been synthesized in polycrystalline form using both arc melting and spark plasma sintering (SPS). The phase formation, hysteresis loss and magnetocaloric properties of the LaFe{sub 11.6}Si{sub 1.4} alloys synthesized using the two different techniques are compared. The annealing time required to obtain the 1:13 phase is significantly reduced from 14 days (using the arc melting technique) to 30 min (using the SPS technique). The magnetic entropy change (ΔS{sub M}) for the arc-melted LaFe{sub 11.6}Si{sub 1.4} compound, obtained for a field change of 5 - 0T (decreasing field), was estimated to be 19.6 J kg{sup -1} K{sup -1}. The effective RCP at 5T of the arc-melted LaFe{sub 11.6}Si{sub 1.4} compound was determined to be 360 J kg{sup -1} which corresponds to about 88 % of that observed in Gd. A significant reduction in the hysteretic losses in the SPS LaFe{sub 11.6}Si{sub 1.4} compound was observed. The ΔS{sub M}, obtained for a field change of 5 - 0T (decreasing field), for the SPS LaFe{sub 11.6}Si{sub 1.4} compound decreases to 7.4 J kg{sup -1} K{sup -1}. The T{sub C} also shifts from 186 (arc-melted) to 230 K (SPS) and shifts the order of phase transition from first to second order, respectively. The MCE of the SPS LaFe{sub 11.6}Si{sub 1.4} compound spreads over a larger temperature range with the RCP value at 5T reaching 288 J kg{sup -1} corresponding to about 70 % of that observed in Gd. At low fields, the effective RCP values of the arc-melted and spark plasma-sintered LaFe{sub 11.6}Si{sub 1.4} compounds are comparable, thereby clearly demonstrating the potential of SPS LaFe{sub 11.6}Si{sub 1.4} compounds in low-field magnetic refrigeration applications. (orig.)

  14. Optimization of magnetocaloric properties of arc-melted and spark plasma-sintered LaFe11.6Si1.4

    Science.gov (United States)

    Shamba, P.; Morley, N. A.; Cespedes, O.; Reaney, I. M.; Rainforth, W. M.

    2016-08-01

    LaFe11.6Si1.4 alloy has been synthesized in polycrystalline form using both arc melting and spark plasma sintering (SPS). The phase formation, hysteresis loss and magnetocaloric properties of the LaFe11.6Si1.4 alloys synthesized using the two different techniques are compared. The annealing time required to obtain the 1:13 phase is significantly reduced from 14 days (using the arc melting technique) to 30 min (using the SPS technique). The magnetic entropy change (Δ S M) for the arc-melted LaFe11.6Si1.4 compound, obtained for a field change of 5 - 0 T (decreasing field), was estimated to be 19.6 J kg-1 K-1. The effective RCP at 5 T of the arc-melted LaFe11.6Si1.4 compound was determined to be 360 J kg-1 which corresponds to about 88 % of that observed in Gd. A significant reduction in the hysteretic losses in the SPS LaFe11.6Si1.4 compound was observed. The Δ S M, obtained for a field change of 5 - 0 T (decreasing field), for the SPS LaFe11.6Si1.4 compound decreases to 7.4 J kg-1 K-1. The T C also shifts from 186 (arc-melted) to 230 K (SPS) and shifts the order of phase transition from first to second order, respectively. The MCE of the SPS LaFe11.6Si1.4 compound spreads over a larger temperature range with the RCP value at 5 T reaching 288 J kg-1 corresponding to about 70 % of that observed in Gd. At low fields, the effective RCP values of the arc-melted and spark plasma-sintered LaFe11.6Si1.4 compounds are comparable, thereby clearly demonstrating the potential of SPS LaFe11.6Si1.4 compounds in low-field magnetic refrigeration applications.

  15. Numerical Analysis of Two-Way Interaction between Weld-Pool and Arc for GTA Welding Process

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A mathematical model to describe the heat transfer and fluid flow in the mutually coupled weld pool and arc by an interactive free surface of the pool for a stationary gas tungsten arc welding (GTAW) is developed. The two sets of governing equations and auxiliary formulas, controlling the weld pool and plasma arc systems respectively, were solved by a finite difference method. A boundary-fitted coordinate system was adopted because the free surface has a curved and unknown shape during welding. The results of this work provide a fundamental basis for predicting the behavior of an integrated weld pool and arc system from first principles.

  16. Laboratory experiments on arc deflection and instability

    Energy Technology Data Exchange (ETDEWEB)

    Zweben, S.; Karasik, M.

    2000-03-21

    This article describes experiments on arc deflection instability carried out during the past few years at the Princeton University Plasma Physics Laboratory (PPPL). The approach has been that of plasma physicists interested in arcs, but they believe these results may be useful to engineers who are responsible for controlling arc behavior in large electric steel furnaces.

  17. Surface Catalysis and Oxidation on Stagnation Point Heat Flux Measurements in High Enthalpy Arc Jets

    Science.gov (United States)

    Nawaz, Anuscheh; Driver, David M.; Terrazas-Salinas

    2013-01-01

    Heat flux sensors are routinely used in arc jet facilities to determine heat transfer rates from plasma plume. The goal of this study is to assess the impact of surface composition changes on these heat flux sensors. Surface compositions can change due to oxidation and material deposition from the arc jet. Systematic surface analyses of the sensors were conducted before and after exposure to plasma. Currently copper is commonly used as surface material. Other surface materials were studied including nickel, constantan gold, platinum and silicon dioxide. The surfaces were exposed to plasma between 0.3 seconds and 3 seconds. Surface changes due to oxidation as well as copper deposition from the arc jets were observed. Results from changes in measured heat flux as a function of surface catalycity is given, along with a first assessment of enthalpy for these measurements. The use of cupric oxide is recommended for future heat flux measurements, due to its consistent surface composition arc jets.

  18. Laboratory Studies of Thermal Energy Charge Transfer of Silicon and Iron Ions in Astrophysical Plasmas

    Science.gov (United States)

    Kwong, Victor H. S.

    1997-01-01

    The laser ablation/ion storage facility at the UNLV Physics Department is dedicated to the study of atomic processes in low temperature plasmas. Our current program is directed to the study of charge transfer of multiply charged ions and neutrals that are of importance to astrophysics at energies less than 1 eV (about 10(exp 4) K). Specifically, we measure the charge transfer rate coefficient of ions such as N(2+), Si(3+), Si(3+), with helium and Fe(2+) with molecular and atomic hydrogen. All these ions are found in a variety of astrophysical plasmas. Their electron transfer reactions with neutral atoms can affect the ionization equilibrium of the plasma.

  19. Application of a radiant heat transfer model to complex industrial reactive flows: combustion chambers, electric arcs; Application d`un modele de transfert radiatif a des ecoulements reactifs industriels complexes: chambres de combustion, arcs electriques

    Energy Technology Data Exchange (ETDEWEB)

    Mechitoua, N.; Dalsecco, S.; Delalondre, C.; Simonin, O. [Electricite de France (EDF), 78 - Chatou (France). Lab. National d`Hydraulique

    1996-12-31

    The direction of studies and researches (DER) of Electricite de France (EdF) has been involved for several years in a research program on turbulent reactive flows. The objectives of this program concern: the reduction of pollutant emissions from existing fossil-fueled power plants, the study of new production means (fluidized beds), and the promotion of electric power applications in the industry. An important part of this program is devoted to the development and validation of 3-D softwares and to the modeling of physical phenomena. This paper presents some industrial applications (furnaces, boilers, electric arcs) for which radiant heat transfers play an important role and the radiation models used. (J.S.) 8 refs.

  20. Effect of Ti-Al on microstructures and mechanical properties of plasma arc in-situ welded joint of SiCp/Al MMCs

    Institute of Scientific and Technical Information of China (English)

    LEI Yu-cheng; ZHANG Zhen; NIE Jia-jun; CHEN Xi-zhang

    2008-01-01

    The effect of Ti-Al on microstructures and mechanical properties of SiCp/Al MMC joints produced by plasma arc in-situ weld-alloying was investigated, in which argon-nitrogen mixture was used as plasma gases and Ti-Al alloy as filling composite. The results show that the formation of needle-like harmful phase Al4C3 is effectively prevented in the weld by in-situ weld-alloying/plasma arc welding with Ti-Al alloy sheet filler whose titanium content is more than 20%. The fluidity of molten pool is improved, and stable molten pool is gained for the addition of the Ti-Al alloy. The mechanical properties of welded joint are effectively enhanced by the compact-grain structure and the new reinforced composites such as Al3Ti, TiN, AlN and TiC welded joint. The test results of mechanical property show that the maximum tensile strength of welded joint gained by adding Ti-60Al alloy is up to 235 MPa. The factors influencing the tensile strength were also investigated.

  1. Heat Transfer and Reconnection Diffusion in Turbulent Magnetized Plasmas

    CERN Document Server

    Lazarian, A

    2011-01-01

    It is well known that magnetic fields constrain motions of charged particles, impeding the diffusion of charged particles perpendicular to magnetic field direction. This modification of transport processes is of vital importance for a wide variety of astrophysical processes including cosmic ray transport, transfer of heavy elements in the interstellar medium, star formation etc. Dealing with these processes one should keep in mind that in realistic astrophysical conditions magnetized fluids are turbulent. In this review we single out a single transport process, namely, heat transfer and consider how it occurs in the presence of the magnetized turbulence. We show that the ability of magnetic field lines to constantly change topology and connectivity is at the heart of the correct description of the 3D magnetic field stochasticity in turbulent fluids. This ability is ensured by fast magnetic reconnection in turbulent fluids and puts forward the concept of reconnection diffusion at the core of the physical pictu...

  2. Energy transfer between degrees of freedom of a dusty plasma system

    Science.gov (United States)

    Semyonov, V. P.; Timofeev, A. V.

    2016-11-01

    Dust particles under certain conditions can acquire kinetic energy of the order of 10 eV and higher, far above the temperature of gas and temperatures of ions and electrons in the discharge. Such heating can be explained by the energy transfer between degrees of freedom of a dusty plasma system. One of the mechanisms of such energy transfer is based on parametric resonance. A model of dust particles system in gas discharge plasma including fluctuations of dust particles charge and features of near-electrode layer is presented. Molecular dynamics simulation of the dust particles system is performed. Conditions of the resonance occurrence are obtained for a wide range of parameters.

  3. SiC Nanowires Synthesized by Rapidly Heating a Mixture of SiO and Arc-Discharge Plasma Pretreated Carbon Black

    Directory of Open Access Journals (Sweden)

    Wang Feng-Lei

    2008-01-01

    Full Text Available Abstract SiC nanowires have been synthesized at 1,600 °C by using a simple and low-cost method in a high-frequency induction furnace. The commercial SiO powder and the arc-discharge plasma pretreated carbon black were mixed and used as the source materials. The heating-up and reaction time is less than half an hour. It was found that most of the nanowires have core-shell SiC/SiO2nanostructures. The nucleation, precipitation, and growth processes were discussed in terms of the oxide-assisted cluster-solid mechanism.

  4. Influence of substrate structure on adhesion behavior of TiN and TiAl3/TiAlN coatings deposited by vacuum arc plasma

    Science.gov (United States)

    Vardanyan, E.; Ramazanov, K.; Yagafarov, I.; Budilov, V.; Agzamov, R.

    2017-05-01

    This paper presents the study of the influence of a substrate structure on the adhesion behavior of monolayer coatings TiN and multilayer coatings TiAl3 / TiAlN deposited by vacuum arc plasma. Martensitic steel with a coarse-grained (CG) and ultrafine-grained (UFG) structure was used for samples. The samples were subjected to ion nitriding in a glow discharge before coating deposition. Adhesion of the coatings was examined with CSM ScratchTEST. For samples with different structures, critical load was defined at which microcracks are formed in the coatings.

  5. MODELING PARAMETERS OF ARC OF ELECTRIC ARC FURNACE

    Directory of Open Access Journals (Sweden)

    R.N. Khrestin

    2015-08-01

    Full Text Available Purpose. The aim is to build a mathematical model of the electric arc of arc furnace (EAF. The model should clearly show the relationship between the main parameters of the arc. These parameters determine the properties of the arc and the possibility of optimization of melting mode. Methodology. We have built a fairly simple model of the arc, which satisfies the above requirements. The model is designed for the analysis of electromagnetic processes arc of varying length. We have compared the results obtained when testing the model with the results obtained on actual furnaces. Results. During melting in real chipboard under the influence of changes in temperature changes its properties arc plasma. The proposed model takes into account these changes. Adjusting the length of the arc is the main way to regulate the mode of smelting chipboard. The arc length is controlled by the movement of the drive electrode. The model reflects the dynamic changes in the parameters of the arc when changing her length. We got the dynamic current-voltage characteristics (CVC of the arc for the different stages of melting. We got the arc voltage waveform and identified criteria by which possible identified stage of smelting. Originality. In contrast to the previously known models, this model clearly shows the relationship between the main parameters of the arc EAF: arc voltage Ud, amperage arc id and length arc d. Comparison of the simulation results and experimental data obtained from real particleboard showed the adequacy of the constructed model. It was found that character of change of magnitude Md, helps determine the stage of melting. Practical value. It turned out that the model can be used to simulate smelting in EAF any capacity. Thus, when designing the system of control mechanism for moving the electrode, the model takes into account changes in the parameters of the arc and it can significantly reduce electrode material consumption and energy consumption

  6. Characteristic Study of DC Electric Arc Plasma Ignitor Jet%直流电弧等离子体点火器射流特性研究

    Institute of Scientific and Technical Information of China (English)

    兰宇丹; 何立明; 杜宏亮; 王峰; 陈鑫

    2012-01-01

    The spectrometer was adopted to measure the emission spectrum of Ar plasma jet at the ignitor exit. Boltzmann curve slope method was applied to calculate the jet electron temperature. Ionization equilibrium equation was used to calculate jet temperature and measure the laws that jet length, jet velocity, electron temperature and jet temperature of ignitor exit change with arc current and inlet Ar flow rate. Whether the electron temperature could be used to replace jet temperature in aircraft plasma arc jet was also discussed. The experiment results show that arc current reduces with the rising of inlet Ar flowrate; exit jet length and velocity increase with the rising of arc current, and increase at first and then reduce with the rising of inlet Ar flow rate; exit electron temperature, electron density and jet temperature increase with the rising of arc current and reduce with the rising of inlet Ar flow rate.%采用光谱仪测量了等离子体点火器出口射流的发射光谱,利用玻尔兹曼曲线斜率法计算了射流的电子温度,并通过电离平衡方程计算了射流气体温度,获得点火器出口射流长度、射流速度、电子温度和射流温度随弧电流及进口氩气流量的变化规律.并分析了航空等离子体电弧射流中是否可使用电子温度来代替射流气体温度.实验表明:弧电流随着进口氩气流量的增大而减小;出口射流长度和速度随弧电流的增大而增大,随进口氩气流量的增大先增大后减小;出口电子温度、电子密度和射流温度随弧电流的增大而升高,随氩气流量的增大而降低.

  7. Physics-Based Modeling of Electric Operation, Heat Transfer, and Scrap Melting in an AC Electric Arc Furnace

    Science.gov (United States)

    Opitz, Florian; Treffinger, Peter

    2016-04-01

    Electric arc furnaces (EAF) are complex industrial plants whose actual behavior depends upon numerous factors. Due to its energy intensive operation, the EAF process has always been subject to optimization efforts. For these reasons, several models have been proposed in literature to analyze and predict different modes of operation. Most of these models focused on the processes inside the vessel itself. The present paper introduces a dynamic, physics-based model of a complete EAF plant which consists of the four subsystems vessel, electric system, electrode regulation, and off-gas system. Furthermore the solid phase is not treated to be homogenous but a simple spatial discretization is employed. Hence it is possible to simulate the energy input by electric arcs and fossil fuel burners depending on the state of the melting progress. The model is implemented in object-oriented, equation-based language Modelica. The simulation results are compared to literature data.

  8. Efficiency of pulse high-current generator energy transfer into plasma liner energy

    Science.gov (United States)

    Oreshkin, V. I.

    2013-08-01

    The efficiency of capacitor-bank energy transfer from a high-current pulse generator into kinetic energy of a plasma liner has been analyzed. The analysis was performed using a model including the circuit equations and equations of the cylindrical shell motion. High efficiency of the energy transfer into kinetic energy of the liner is shown to be achieved only by a low-inductance generator. We considered an "ideal" liner load in which the load current is close to zero in the final of the shell compression. This load provides a high (up to 80%) efficiency of energy transfer and higher stability when compressing the liner.

  9. Development of innovative thermal plasma and particle diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Bachmann, Benjamin-Leon

    2013-09-24

    Three original plasma diagnostic systems have been developed to investigate transient three-dimensional plasma processes with high spatial and temporal resolution. The developed diagnostics have been analyzed and tested by increasing the complexity from a stationary free burning Argon arc to a dc pulsed process and finally to a transient gas metal arc including droplet transfer through the plasma. The transient plasma parameters that have been determined include three-dimensional axially symmetric plasma densities (n{sub e}, n{sub A}, n{sub A+}, n{sub A++}), electron temperatures (T{sub e}), electrical conductivities (σ{sub el}), magnetic flux densities (B) and current densities (j{sub el}). In the case of a droplet transfer through an arc consisting of an Iron/Argon plasma, the droplet density, surface tension, viscosity, and temperature have been determined.

  10. Diagnosis of gas phase near the substrate surface in diamond film deposition by high-power DC arc plasma jet CVD

    Institute of Scientific and Technical Information of China (English)

    Zuyuan Zhou; Guangchao Chen; Bin Li; Weizhong Tang; Fanxiu Lv

    2007-01-01

    Optical emission spectroscopy (OES) was used to study the gas phase composition near the substrate surface during diamond deposition by high-power DC arc plasma jet chemical vapor deposition (CVD). C2 radical was determined as the main carbon radical in this plasma atmosphere. The deposition parameters, such as substrate temperature, anode-substrate distance, methane concentration, and gas flow rate, were inspected to find out the influence on the gas phase. A strong dependence of the concentrations and distribution of radicals on substrate temperature was confirmed by the design of experiments (DOE). An explanation for this dependence could be that radicals near the substrate surface may have additional ionization or dissociation and also have recombination,or are consumed on the substrate surface where chemical reactions occur.

  11. Predictive value of plasma hCG measured 14 days after Day-2 single embryo transfer

    DEFF Research Database (Denmark)

    Løssl, Kristine; Oldenburg, Anna; Toftager, Mette

    2017-01-01

    INTRODUCTION: Prediction of pregnancy outcome after IVF is important for patients and clinicians. Early plasma hCG (p-hCG) levels are the best known predictor of pregnancy outcome, but no studies has been restricted to single embryo transfer (SET) of Day-2 embryos. The aim of the present study...

  12. Enhancing Micro-Cathode Arc Thruster (muCAT) Plasma Generation to Analyze Magnetic Field Angle Effects on Sheath Formation in Hall Thrusters

    Science.gov (United States)

    Lukas, Joseph Nicholas

    Using a Delta IV or Atlas V launch vehicle to send a payload into Low Earth Orbit can cost between 13,000 and 14,000 per kilogram. With payloads that utilize a propulsion system, maximizing the efficiency of that propulsion system would not only be financially beneficial, but could also increase the range of possible missions and allow for a longer mission lifetime. This dissertation looks into efficiency increases in the Micro-Cathode Arc Thruster (muCAT) and Hall Thruster. The muCAT is an electric propulsion device that ablates solid cathode material, through an electrical arc discharge, to create plasma and ultimately produce thrust. About 90% of the arc discharge current is conducted by electrons, which go toward heating the anode and contribute very little to thrust, with only the remaining 10% going toward thrust in the form of ion current. I will discuss the results of an experiment in which electron heating on a low melting point anode was shown to increase ion current, which theoretically should increase thrust levels at low frequencies. Another feature of the muCAT is the use of an external magnetic solenoid which increases thrust, ion current, and causes uniform cathode erosion. An experiment has shown that efficiency can also be increased by removing the external magnetic field power supply and, instead, utilizing the residual arc current to power the magnetic solenoid. A Hall Thruster is a type of electric propulsion device that accelerates ions across an electric potential between an anode and magnetically trapped electrons. The limiting factor in Hall Thruster operation is the lifetime of the wall material. During operation, a positively charged layer forms over the surface of the walls, known as a plasma sheath, which contributes to wall erosion. Therefore, by reducing or eliminating the sheath layer, Hall Thruster operational lifetime can increase. Computational modeling has shown that large magnetic field angles and large perpendicular electric

  13. [Study on the arc spectral information for welding quality diagnosis].

    Science.gov (United States)

    Li, Zhi-Yong; Gu, Xiao-Yan; Li, Huan; Yang, Li-Jun

    2009-03-01

    Through collecting the spectral signals of TIG and MIG welding arc with spectrometer, the arc light radiations were analyzed based on the basic theory of plasma physics. The radiation of welding arc distributes over a broad range of frequency, from infrared to ultraviolet. The arc spectrum is composed of line spectra and continuous spectra. Due to the variation of metal density in the welding arc, there is great difference between the welding arc spectra of TIG and MIG in both their intensity and distribution. The MIG welding arc provides more line spectra of metal and the intensity of radiation is greater than TIG. The arc spectrum of TIG welding is stable during the welding process, disturbance factors that cause the spectral variations can be reflected by the spectral line related to the corresponding element entering the welding arc. The arc spectrum of MIG welding will fluctuate severely due to droplet transfer, which produces "noise" in the line spectrum aggregation zone. So for MIG welding, the spectral zone lacking spectral line is suitable for welding quality diagnosis. According to the characteristic of TIG and MIG, special spectral zones were selected for welding quality diagnosis. For TIG welding, the selected zone is in ultraviolet zone (230-300 nm). For MIG welding, the selected zone is in visible zone (570-590 nm). With the basic theory provided for welding quality diagnosis, the integral intensity of spectral signal in the selected zone of welding process with disturbing factor was studied to prove the theory. The results show that the welding quality and disturbance factors can be diagnosed with good signal to noise ratio in the selected spectral zone compared with signal in other spectral zone. The spectral signal can be used for real-time diagnosis of the welding quality.

  14. 中频真空电弧的等离子体特性%Plasma Characteristics of Intermediate-frequency Vacuum Arc

    Institute of Scientific and Technical Information of China (English)

    王景; 武建文

    2011-01-01

    The vacuum switch used in intermediate frequency (360-800 Hz) power system of more/all electric aircraft is being developed, and the theoretical understanding of the arcing process at intermediate frequency is increasing. The continuum emission theory of arc plasma was analyzed, electron temperature and electron density of intermediate frequency (400-800 Hz) vacuum arc were obtained by application of a simplified optical-channel model and detection on the intensities of dual-narrowband continuum emission spectra. Then, a plasma-parameter diagnostic system was designed to implement the above measurement. This system consists of a color CCD camera with a dual-narrowband filter and arc-motion picture analysis software, and it can record the arc appearance and the data for measurement simultaneously. After calibrated by using standard source of radiance temperature, the system was applied to observe the arc mode evolution and measure the plasma parameters. The results confirmed the validity of analysis and measurement in this work. At intermediate frequency, the transition arc mode and the diffuse arc mode exist during arc evolution. The transition arc evolves rapidly, and converts into the diffuse arc at the peak current. At the current peak of 8 kA with different frequencies, the electron temperature varies from 0.5-3 eV, and the electron density ranges from 10^20-10^21 m^-3, which are in agreement with those achieved by other researchers.%目前应用于未来多电和全电飞机(电流频率360~800Hz)的中频真空开关正成为研究热点,中频真空电弧理论的研究正不断深入。分析了电弧等离子体连续光谱的辐射理论,在假定中频真空电弧处于部分局部热力学平衡态(partial local thermodynamic equilibrium,PLTE)的基础上,结合实际光学通路的简化模型,得到通过双波段窄带连续光谱测量电子温度和电子密度的方法,然后设计了中频真空电弧的参数测量

  15. Experimental study of plasma energy transfer and material erosion under ELM-like heat loads

    Energy Technology Data Exchange (ETDEWEB)

    Garkusha, I.E., E-mail: garkusha@ipp.kharkov.u [Institute of Plasma Physics of the NSC KIPT, Akademicheskaya 1, 61108 Kharkov (Ukraine); Makhlaj, V.A.; Chebotarev, V.V. [Institute of Plasma Physics of the NSC KIPT, Akademicheskaya 1, 61108 Kharkov (Ukraine); Landman, I. [Forschungszentrum Karlsruhe, IHM, 76021 Karlsruhe (Germany); Tereshin, V.I.; Aksenov, N.N.; Bandura, A.N. [Institute of Plasma Physics of the NSC KIPT, Akademicheskaya 1, 61108 Kharkov (Ukraine)

    2009-06-15

    Main features of plasma-surface interaction and energy transfer to tokamak plasma facing components are studied at different heat loads in ELM simulation experiments with the plasma gun QSPA Kh-50. Repetitive plasma exposures of tungsten, graphite and different combined W-C targets were performed at the pulse duration of 0.25 ms and the heat loads varied in the range 0.2-2.5 MJ/m{sup 2}. The onset of vapor shield in front of the surface was investigated. The evaporation is immediately followed by a saturation of surface heat load if further increasing the impact energy. The presence of graphite essentially decreases the heat flux to the nearby tungsten surface, which is due to the carbon vapor shield. Droplet splashing at the tungsten surface and formation of hot spots on the graphite surface are discussed.

  16. Preferential transfer of certain plasma membrane proteins onto T and B cells by trogocytosis.

    Directory of Open Access Journals (Sweden)

    Sandrine Daubeuf

    Full Text Available T and B cells capture antigens via membrane fragments of antigen presenting cells (APC in a process termed trogocytosis. Whether (and how a preferential transfer of some APC components occurs during trogocytosis is still largely unknown. We analyzed the transfer onto murine T and B cells of a large panel of fluorescent proteins with different intra-cellular localizations in the APC or various types of anchors in the plasma membrane (PM. Only the latter were transferred by trogocytosis, albeit with different efficiencies. Unexpectedly, proteins anchored to the PM's cytoplasmic face, or recruited to it via interaction with phosphinositides, were more efficiently transferred than those facing the outside of the cell. For proteins spanning the PM's whole width, transfer efficiency was found to vary quite substantially, with tetraspanins, CD4 and FcRgamma found among the most efficiently transferred proteins. We exploited our findings to set immunodiagnostic assays based on the capture of preferentially transferred components onto T or B cells. The preferential transfer documented here should prove useful in deciphering the cellular structures involved in trogocytosis.

  17. Low-energy plasma immersion ion implantation to induce DNA transfer into bacterial E. coli

    Energy Technology Data Exchange (ETDEWEB)

    Sangwijit, K. [Biotechnology Unit, University of Phayao, Muang, Phayao 56000 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Sarapirom, S. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Bang Khen, Chiang Mai 50290 (Thailand); Pitakrattananukool, S. [School of Science, University of Phayao, Muang, Phayao 56000 (Thailand); Anuntalabhochai, S. [Biotechnology Unit, University of Phayao, Muang, Phayao 56000 (Thailand)

    2015-12-15

    Plasma immersion ion implantation (PIII) at low energy was for the first time applied as a novel biotechnology to induce DNA transfer into bacterial cells. Argon or nitrogen PIII at low bias voltages of 2.5, 5 and 10 kV and fluences ranging from 1 × 10{sup 12} to 1 × 10{sup 17} ions/cm{sup 2} treated cells of Escherichia coli (E. coli). Subsequently, DNA transfer was operated by mixing the PIII-treated cells with DNA. Successes in PIII-induced DNA transfer were demonstrated by marker gene expressions. The induction of DNA transfer was ion-energy, fluence and DNA-size dependent. The DNA transferred in the cells was confirmed functioning. Mechanisms of the PIII-induced DNA transfer were investigated and discussed in terms of the E. coli cell envelope anatomy. Compared with conventional ion-beam-induced DNA transfer, PIII-induced DNA transfer was simpler with lower cost but higher efficiency.

  18. 用于网格状金属切割的等离子切割电源控制策略研究%Research on control strategy of plasma arc cutting power supply used for grid plates cutting

    Institute of Scientific and Technical Information of China (English)

    陈桂涛; 刘春强; 孙强; 钟彦儒

    2015-01-01

    For solving the problem that how to control arc current accurately in the process of cutting grid plates, an arc current reference feedforward composite control strategy was proposed, which was based on the analysis of arc transfer process and arc model. The external loop of control strategy is current loop, which can control arc current and achieve the precise control of arc energy. Arc current reference feedforward compensation based on load model was introduced into voltage inner loop. The voltage loop can quickly establish the arc voltage, which maintains the arc stable. Simulations and experimental results were given to verify that the proposed control method can respond quickly between non⁃transferred arc and transferred arc when cutting grid plates,and can achieve the precise control of arc current simultaneously.%为解决金属网格切割过程中精确控制弧电流的问题,在分析金属网格切割弧转移过程、建立电弧模型的基础上,提出一种基于电弧负载模型的弧电流指令前馈的复合控制策略。控制策略外环为电流环,实现等离子电弧电流及能量控制;在电压内环引入基于电弧负载模型的弧电流指令前馈控制,通过前馈控制的快速性迅速建立弧柱电压,达到维持电弧稳定的目的。仿真和实验结果表明,提出的控制策略能够快速响应网格状金属切割时引弧过程及非转移弧和转移弧之间的快速切换需求,实现弧电流的快速精确控制。

  19. Laboratory Studies of Thermal Energy Charge Transfer of Multiply Charged Ions in Astrophysical Plasmas

    Science.gov (United States)

    Kwong, Victor H. S.

    2003-01-01

    The laser ablation/ion storage facility at the UNLV Physics Department has been dedicated to the study of atomic and molecular processes in low temperature plasmas. Our program focuses on the charge transfer (electron capture) of multiply charged ions and neutrals important in astrophysics. The electron transfer reactions with atoms and molecules is crucial to the ionization condition of neutral rich photoionized plasmas. With the successful deployment of the Far Ultraviolet Spectroscopic Explorer (FUSE) and the Chandra X-ray Observatory by NASA high resolution VUV and X-ray emission spectra fiom various astrophysical objects have been collected. These spectra will be analyzed to determine the source of the emission and the chemical and physical environment of the source. The proper interpretation of these spectra will require complete knowledge of all the atomic processes in these plasmas. In a neutral rich environment, charge transfer can be the dominant process. The rate coefficients need to be known accurately. We have also extended our charge transfer measurements to KeV region with a pulsed ion beam. The inclusion of this facility into our current program provides flexibility in extending the measurement to higher energies (KeV) if needed. This flexibility enables us to address issues of immediate interest to the astrophysical community as new observations are made by high resolution space based observatories.

  20. Alternating-Polarity Arc Welding

    Science.gov (United States)

    Schwinghamer, R. J.

    1987-01-01

    Brief reversing polarity of welding current greatly improves quality of welds. NASA technical memorandum recounts progress in art of variable-polarity plasma-arc (VPPA) welding, with emphasis on welding of aluminum-alloy tanks. VPPA welders offer important advantages over conventional single-polarity gas/tungsten arc welders.

  1. Net Emission Coefficients for Copper and Iron Plasmas

    Science.gov (United States)

    Kassubek, Frank; Zilberberg, Oded; Doiron, Charles

    2016-09-01

    Radiative heat transfer is an important mechanism for heat transport in electrical arcs, e.g. in electrical switchgear. An exact description of this phenomenon is important (i) for the energy balance of the arc itself, and (ii) for the estimate of the escaping radiation that leads to evaporation of polymer nozzles; the evaporated material and its flow have a strong effect on the arcs. For low voltage arcs, the plasma composition within the arc is dominated by the contact material. In the present study, we compare copper and iron. Especially, we discuss the calculation of absorption and emission spectra and their characterisation by net emission coefficients. The latter describe well the effective power balance at the centre of the arc. We show that in addition to the net emission coefficients, it is important to characterise the radiation that is emitted from the arc core.

  2. General relativistic radiative transfer in hot astrophysical plasmas a characteristic approach

    CERN Document Server

    Zane, S; Nobili, L; Erna, M; Zane, Silvia; Turolla, Roberto; Nobili, Luciano; Erna, Myris

    1996-01-01

    In this paper we present a characteristic method for solving the transfer equation in differentially moving media in a curved spacetime. The method is completely general, but its capabilities are exploited at best in presence of symmetries, when the existence of conserved quantities allows to derive analytical expressions for the photon trajectories in phase space. In spherically--symmetric, stationary configurations the solution of the transfer problem is reduced to the integration of a single ordinary differential equation along the bi--parametric family of characteristic rays. Accurate expressions for the radiative processes relevant to continuum transfer in a hot astrophysical plasma have been used in evaluating the source term, including relativistic e--p, e--e bremsstrahlung and Compton scattering. A numerical code for the solution of the transfer problem in moving media in a Schwarzschild spacetime has been developed and tested. Some applications, concerning ``hot'' and ``cold'' accretion onto non--rot...

  3. Changes in Properties of Dielectric Barrier Discharge Plasma Jets for Different Gases and for Insulating and Conducting Transfer Plates

    Science.gov (United States)

    do Nascimento, Fellype; Moshkalev, Stanislav; Machida, Munemasa

    2017-03-01

    Dielectric barrier discharge (DBD) plasma jets have been studied extensively in recent years because of its wide range of applications. DBD plasmas can be produced using many different gases and can be applied to a broad variety of surfaces and substrates. This work provides comparisons of DBD plasmas generated using argon (Ar), helium (He), and nitrogen (N2), as well as their mixtures with water vapor in order to know how some plasma properties are affected by the use of different gases. All plasmas were studied in two different conditions: using a transfer plate made of a conductive material and using a transfer plate made of an insulating one. It was observed that the process of Penning ionization of nitrogen molecules by direct collisions with metastable atoms and molecules is evident and significant only in plasmas that use He as the working gas, which means that He atoms in metastable states have greater ability to transfer energy to molecules of nitrogen in the plasma. The collisions of metastable He with N2 molecules determine the vibrational temperature (T vib) values in He plasmas, while in Ar and N2 plasmas, the T vib values are determined mainly by collisions of electrons with N2 molecules. It was noticed that the use of an insulating or a conducting transfer plate as the sample holder affects the results of adhesion between poly(dimethylsiloxane) samples, and it is mainly due to the differences in the plasma power, with a higher plasma power leading to better adhesion.

  4. Modeling rf breakdown arcs

    CERN Document Server

    Insepov, Zeke; Huang, Dazhang; Mahalingam, Sudhakar; Veitzer, Seth

    2010-01-01

    We describe breakdown in 805 MHz rf accelerator cavities in terms of a number of mechanisms. We devide the breakdown process into three stages: (1) we model surface failure using molecular dynamics of fracture caused by electrostatic tensile stress, (2) we model the ionization of neutrals responsible for plasma initiation and plasma growth using a particle in cell code, and (3) we model surface damage by assuming a process similar to unipolar arcing. Although unipolar arcs are strictly defined with equipotential boundaries, we find that the cold, dense plasma in contact with the surface produces very small Debye lengths and very high electric fields over a large area. These high fields produce strong erosion mechanisms, primarily self sputtering, compatible with the crater formation that we see. Results from the plasma simulation are included as a guide to experimental verification of this model.

  5. The role of current characteristics of the arc evaporator in formation of the surface metal-coating composite

    Science.gov (United States)

    Plikhunov, V. V.; Petrov, L. M.; Grigorovich, K. V.

    2016-07-01

    The influence of current characteristics of the vacuum arc evaporator on the interaction process of plasma streams with the surface under treatment during generation of the physicochemical properties of the formed metal-coating composite is considered. It is shown that the interaction of plasma streams with the processed surface provides surface heating, defects elimination, change in energy properties, and mass transfer of plasma stream elements activating surface diffusion processes whose intensity is evaluated by the arc current magnitude and location of the processed surface relative to the cathode axis.

  6. 自保护药芯焊丝弧桥并存过渡试验分析%Experimental analysis of bridging transfer without arc interruption of self-shielded flux cored wire

    Institute of Scientific and Technical Information of China (English)

    王志明; 刘海云; 王勇; 张英乔

    2011-01-01

    采用高速摄影、汉诺威弧焊质量分析仪和体式显微镜对自保护药芯焊丝弧桥并存过渡特征和过渡机理进行了试验研究,结果表明:弧桥并存过渡是一种液桥持续存在的同时电弧不熄灭的熔滴过渡模式,是自保护药芯焊丝主要熔滴过渡模式之一;电弧电压和焊接电流波形没有短路过渡特征,表现为一定范围内小幅波动,与弧桥并存过渡特征相对应;电压概率密度分布曲线和电流概率密度曲线都没有短路过渡的特征;弧桥并存过渡的液桥是由熔融渣包裹液态金属混合形成的;自保护药芯焊丝孤桥并存过渡主要是在表面张力和电磁收缩力的共同作用下完成.%By using the high speed photography,Hanover analyzer and macro-microscope,the tranfer characteristic and the tranfer mechanisim of metal transfer of self-shielded flux cored wire have been studied.The results reaveal that bridging transfer without arc interruption transfer is a kind of transfer which the bridge exists lastingly while the arc isn't extinguished,and it is one of the metal transfer models of self-shielded flux cored wire.Without the characteristic of short-circuit transfer,the wave pattern of arc voltage and welding current represent the slight waving within a certain scope,corresponding to the characteristic of bridging transfer without arc interruption,the U-PDD & I-PDD doesn't show the characteristic of short circuit transfer.The bridge of bridging transfer without arc interruption is formed of mixture of the slag's covering the liquid metal.The accomplishment of bridging transfer without arc interruption is mainly conducted by joint work of surface tension and electromagnetic force.

  7. Variable polarity arc welding

    Science.gov (United States)

    Bayless, E. O., Jr.

    1991-01-01

    Technological advances generate within themselves dissatisfactions that lead to further advances in a process. A series of advances in welding technology which culminated in the Variable Polarity Plasma Arc (VPPA) Welding Process and an advance instituted to overcome the latest dissatisfactions with the process: automated VPPA welding are described briefly.

  8. Deposition of thin layers of boron nitrides and hydrogenated microcrystalline silicon assisted by high current direct current arc plasma; Deposition assistee par un plasma a arc a haut courant continu de couches minces de Nitrure de Bore et de Silicium microcristallin hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    Franz, D. [Ecole Polytechnique Federale de Lausanne, Centre de Recherches en Physique des Plasmas (CRPP), CH-1015 Lausanne (Switzerland)

    1999-09-01

    In the frame of this thesis, a high current direct current arc (HCDCA) used for the industrial deposition of diamond, has been adapted to study the deposition of two types of coatings: a) boron nitride, whose cubic phase is similar to diamond, for tribological applications, b) hydrogenated microcrystalline silicon, for applications in the semiconductor fields (flat panel displays, solar cells,...). For the deposition of these coatings, the substrates were placed in the diffusion region of the arc. The substrate heating is mainly due to atomic species recombining on its surface. The deposition temperature, varying from 300 to 900 {sup o}C according to the films deposited, is determined by the substrate position, the arc power and the injected gas fluxes, without the use of any external heating or cooling system. Measurements performed on the arc plasma show that the electronic temperature is around 2 eV (23'000 K) while the gas temperature is lower than 5500 K. Typical electronic densities are in the range of 10{sup 12}-10{sup 1'}3 cm{sup -3}. For the deposition of boron nitride films, different boron precursors were used and a wide parameter range was investigated. The extreme difficulty of synthesising cubic boron nitride films by chemical vapour deposition (CVD) did not allow to stabilize the cubic phase of boron nitride in HCDCA. Coatings resulted in hexagonal or amorphous boron nitride with a chemical composition close to stoichiometric. The presence of hydrogen leads to the deposition of rough and porous films. Negative biasing of the samples, for positive ion bombardment, is commonly used to stabilize the cubic phase. In HCDCA and in our biasing range, only a densification of the films could be observed. A boron nitride deposition plasma study by infrared absorption spectroscopy in a capacitive radio frequency reactor has demonstrated the usefulness of this diagnostic for the understanding of the various chemical reactions which occur in this kind

  9. Study On the Tribological Behavior of the Arc-added Glow Discharge Plasma Non-hydrogen Carburization On Titanium Alloy Surfaces

    Institute of Scientific and Technical Information of China (English)

    CHEN Fei; ZHAHGYue-fei; Liu Yu; TANG Bin; PAN Jun-de

    2004-01-01

    This paper introduces a new titanium alloys surface strengthening treatment by using the arc-added glow discharge plasmas non-hydrogen carburization technique. High purity and high strength graphite is selected as cooling cathode arc source for supplying carbon atoms and particle, which migrate to the titanium alloy(Ti6Al4V) surface and form modified layer. Thus, the hydrogen embrittlement is avoided while the tribological behavior of the titanium alloy surface is improved in the respects of anti-friction and anti-wear ability. The tribological behavior of the modified layer under dry sliding against SAE52100 steel was evaluated on a ball-on-disc test rig. The results showed that the modified layer obtained a thickness of 30μm at 980℃, 30minutes. The microhardness of the Ti6A14V alloy surface attained 936 HV, which was much larger than that of the Ti6A14V alloy. The Ti6A14V alloy was characterized by adhesion wear and scuffing under dry sliding against the steel, while the surface modified layer experienced much abated adhesion wear and scuffing under the same testing condition. This could be attributed to the carbon element with different modalities exists in the modified layer.The modified layer showed good friction-reducing and fair anti-wear ability in dry sliding against the steel. Using the SEM,XRD and XPS, the phase structure and morphology of the carburization modified layer was analyzed.

  10. Behaviour of the iron vapour core in the arc of a controlled short-arc GMAW process with different shielding gases

    Science.gov (United States)

    Wilhelm, G.; Kozakov, R.; Gött, G.; Schöpp, H.; Uhrlandt, D.

    2012-02-01

    The controlled metal transfer process (CMT) is a variation of the gas metal arc welding (GMAW) process which periodically varies wire feeding speed. Using a short-arc burning phase to melt the wire tip before the short circuit, heat input to the workpiece is reduced. Using a steel wire and a steel workpiece, iron vapour is produced in the arc, its maximum concentration lying centrally. The interaction of metal vapour and welding gas considerably impacts the arc profile and, consequently, the heat transfer to the weldpool. Optical emission spectroscopy has been applied to determine the radial profiles of the plasma temperature and iron vapour concentration, as well as their temporal behaviour in the arc period for different mixtures of Ar, O2 and CO2 as shielding gases. Both the absolute iron vapour density and the temporal expansion of the iron core differ considerably for the gases Ar + 8%O2, Ar + 18% CO2 and 100% CO2 respectively. Pronounced minimum in the radial temperature profile is found in the arc centre in gas mixtures with high Ar content under the presence of metal vapour. This minimum disappears in pure CO2 gas. Consequently, the temperature and electrical and thermal conductivity in the arc when CO2 is used as a shielding gas are considerably lower.

  11. Charge-state and element-resolved ion energies in the cathodic arc plasma from composite AlCr cathodes in argon, nitrogen and oxygen atmospheres

    CERN Document Server

    Franz, Robert; Anders, André

    2014-01-01

    The energy distribution functions of ions in the cathodic arc plasma using composite AlCr cathodes were measured as a function of the background gas pressure in the range 0.5 to 3.5 Pa for different cathode compositions and gas atmospheres. The most abundant aluminium ions were Al$^{+}$ regardless of the background gas species, whereas Cr$^{2+}$ ions were dominating in Ar and N$_2$ and Cr$^{+}$ in O$_2$ atmospheres. The energy distributions of the aluminium and chromium ions typically consisted of a high energy fraction due to acceleration in the expanding plasma plume from the cathode spot and thermalised ions that were subjected to collisions in the plasma cloud. The fraction of the latter increased with increasing background gas pressure. Atomic nitrogen and oxygen ions showed similar energy distributions as the aluminium and chromium ions, whereas the argon and molecular nitrogen and oxygen ions were mainly thermalised. In addition to the positively charged metal and gas ions, negatively charged oxygen an...

  12. Optimization Of Pulsed Current Parameters To Minimize Pitting Corrosion İn Pulsed Current Micro Plasma Arc Welded Aısı 304l Sheets Using Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Kondapalli Siva Prasad

    2013-06-01

    Full Text Available Austenitic stainless steel sheets have gathered wide acceptance in the fabrication of components, which require high temperature resistance and corrosion resistance, such as metal bellows used in expansion joints in aircraft, aerospace and petroleum industry. In case of single pass welding of thinner sections of this alloy, Pulsed Current Micro Plasma Arc Welding (PCMPAW was found beneficial due to its advantages over the conventional continuous current process. This paper highlights the development of empirical mathematical equations using multiple regression analysis, correlating various process parameters to pitting corrosion rates in PCMPAW of AISI 304L sheets in 1 Normal HCl. The experiments were conducted based on a five factor, five level central composite rotatable design matrix. A Genetic Algorithm (GA was developed to optimize the process parameters for minimizing the pitting corrosion rates.

  13. Residual stress distribution in thin diamond films and its effects on preparation of thick freestanding diamond films using DC arc plasma jet operated at gas recycling mode

    Institute of Scientific and Technical Information of China (English)

    LI Cheng-ming; LI Hui-qing; CHEN Guan-chao; L(U) Fan-xiu; TONG Yu-mei; TANG Wei-zhong

    2004-01-01

    Diamond films produced by chemical vapor deposition show excellent properties. The residual stress distribution of diamond thin films deposited by DC arc plasma jet at recycling mode was analyzed by line shifts of micro Raman spectroscopy. The results show that the compressive residual stress concentrates at the film's edge. The experimental observations show that cracks initiate at the edge of the diamond thick wafer and then propagate towards the center. The residual stress of diamond films increases with the increase of methane concentration and deposition temperature. The difference of adhesion in close area causes more shear stress and brings about the two sides of crack being not at same level. To suppress crack probability, it is favourable for increasing the film thickness and selecting a substrate with lower coefficient of thermal expansion and lower adhesion. The effects of the residual stress distribution on thick diamond films detachment were discussed.

  14. Time-Resolved Spectroscopic Observation of Deposition Processes of Ultrananocrystalline Diamond/Amorphous Carbon Composite Films by Using a Coaxial Arc Plasma Gun

    Science.gov (United States)

    Hanada, Kenji; Yoshitake, Tsuyoshi; Nishiyama, Takashi; Nagayama, Kunihito

    2010-08-01

    The deposition of ultrananocrystalline diamond (UNCD)/amorphous carbon composite films using a coaxial arc plasma gun in vacuum and, for comparison, in a 53.3 Pa hydrogen atmosphere was spectroscopically observed using a high-speed camera equipped with narrow-band-pass filters. UNCD crystallites with diameters of approximately 1.6 nm were formed even in vacuum. These extremely small crystallites imply that the formation is predominantly due to nucleation without the subsequent growth. Even in vacuum, emissions from C+ ions, C atoms, and C2 dimers lasted for approximately 100 µs, although the emission lifetimes of these species are generally 10 ns. We consider that the nucleation is due to the supersaturated environment containing excited carbon species with large number densities.

  15. Effects of deposition parameters on microstructure and thermal conductivity of diamond films deposited by DC arc plasma jet chemical vapor deposition

    Institute of Scientific and Technical Information of China (English)

    QU Quan-yan; QIU Wan-qi; ZENG De-chang; LIU Zhong-wu; DAI Ming-jiang; ZHOU Ke-song

    2009-01-01

    The uniform diamond films with 60 mm in diameter were deposited by improved DC arc plasma jet chemical vapor deposition technique. The structure of the film was characterized by scanning electronic microcopy(SEM) and laser Raman spectrometry. The thermal conductivity was measured by a photo thermal deflection technique. The effects of main deposition parameters on microstructure and thermal conductivity of the films were investigated. The results show that high thermal conductivity, 10.0 W/(K-cm), can be obtained at a CH4 concentration of 1.5% (volume fraction) and the substrate temperatures of 880-920 ℃ due to the high density and high purity of the film. A low pressure difference between nozzle and vacuum chamber is also beneficial to the high thermal conductivity.

  16. Chemical bonding structural analysis of nitrogen-doped ultrananocrystalline diamond/hydrogenated amorphous carbon composite films prepared by coaxial arc plasma deposition

    Science.gov (United States)

    Gima, Hiroki; Zkria, Abdelrahman; Katamune, Yūki; Ohtani, Ryota; Koizumi, Satoshi; Yoshitake, Tsuyoshi

    2017-01-01

    Nitrogen-doped ultra-nanocrystalline diamond/hydrogenated amorphous carbon composite films prepared in hydrogen and nitrogen mixed-gas atmospheres by coaxial arc plasma deposition with graphite targets were studied electrically and chemical-bonding-structurally. The electrical conductivity was increased by nitrogen doping, accompanied by the production of n-type conduction. From X-ray photoemission, near-edge X-ray absorption fine-structure, hydrogen forward-scattering, and Fourier transform infrared spectral results, it is expected that hydrogen atoms that terminate diamond grain boundaries will be partially replaced by nitrogen atoms and, consequently, π C–N and C=N bonds that easily generate free electrons will be formed at grain boundaries.

  17. Experim ental research in plasma arc cutting engineering ceramics%工程陶瓷的等离子弧切割实验研究

    Institute of Scientific and Technical Information of China (English)

    徐文骥; 蒋希时; 金洙吉

    2001-01-01

    Based on the analysis of the present situation and the characteristics of the technology of laser cutting, abrasive water-jet cutting, WEDM on engineering ceramics, a new method-additional positive pole plasma arc cutting is offered. The feasibility of the method has been proved by experiments. The method has its own advantage and good prospect.%在分析采用激光、磨料水射流、电火花线切割等方法切割工程陶瓷技术的现状与特点的基础上,提出采用附加阳极等离子弧切割工程陶瓷的基本思想,通过实验证明上述方法可行且具有独特的优点,显示出良好的应用前景。

  18. THE LIFETIME EXTENSION OF CAR AXLES TYPES OF RU1 AND RUSH WHEELSET FREIGHT CARS, RESTORED BY THE METHOD OF PLASMA-ARC METALLIZATION OF THE NECK AND UNDER PARTS MANUAL

    Directory of Open Access Journals (Sweden)

    V. I. Zelenin

    2009-03-01

    Full Text Available The restoration method for the journals and wheel seats of the freight wagon wheelsets by means of plasma-arc metallization is presented and the results of the bench fatigue tests with the advisable operation life of the axles restored are given.

  19. Heat Transfer to a Particle Exposed to a Rarefied Plasma with a Great Temperature Gradient

    Institute of Scientific and Technical Information of China (English)

    XiChen; XinTao

    1993-01-01

    A kinetic-theory analysis is presented concerning the heat transfer from a rarefiled plasma to a spherical particle for the extreme case of free-molecule regime and thin phasma sheath.A great temperature gradient is assumed to exist in the plasma,and thus a non-Maxwellian velocity distribution function is employed for each of the gas species.Analytical results show that the existence of a temperature in employed for each of the gas species,Analytical results show that the existence of a temperature gradient in the plasma causes a nonuniform distribution of the local heat flux density on the sphere surface,while the total heat flux to the whole particle is independent of the temperature gradient.The nonuniformity of the local heat flux distributioln is small even for the case with a temperature gradient as great as 106 K/m,but it may significantly enhance the thermophoretic force on an evaporating particle,Heat transfer is mainly caused by atome at low gas temperatures with negligible ionization degree,while it can be attributed to ions and electrons at high plasma temperatures.

  20. Magma transfer and degassing budget: Application to the 2009-2010 eruptive crisis of Mt Garet (Vanuatu arc)

    Science.gov (United States)

    Métrich, N.; Bertagnini, A.; Garaebiti, E.; Vergniolle, S.; Bani, P.; Beaumais, A.; Neuville, D. R.

    2016-08-01

    Mt Garet, on Gaua Island, is one of the active volcanoes of the Vanuatu arc. We report here a new dataset on lapilli and lava erupted during Mt Garet unrest in 2009-2010 and on products of the older activity of Gaua composite volcano. The present-day magma of Mt Garet is a trachy-andesite (52 wt.% SiO2) with relatively high Rb/Th (14.6) and Ba/La (41) ratios compared to the Gaua pre- and syn-caldera series, but typical of the central part of Vanuatu arc. Its mineral assemblage is mainly composed of plagioclase (An86-56) and clinopyroxene (Fs5-16) which display significant chemical variations, patchy zones, surface dissolution, and oscillatory zoning that imply episodes of high undercooling and growth rates. The paragenesis is complemented by Fe-Ti oxides and scarce olivine (Fo72-73). The melt inclusions are ubiquitous and their compositions cover a chemical spectrum from basalt to trachy-andesite. Volatile-rich basaltic inclusions (H2O: 2.7 wt.%, S: 0.15 wt.%, and Cl: 0.22 wt.%) are preserved in Mg-rich clinopyroxene whereas the majority of the melt inclusions is volatile poorer with, ≤ 1.0 wt.% of H2O, ≤ 0.05 wt.% of S, and 0.25-0.27 wt.% of Cl. At 1100 °C the measured viscosity of anhydrous magma of Mt Garet is 103.5 Pa s. Adding 0.8 to 2.5 wt.% of H2O decreases the melt viscosity by 0.5 to two orders of magnitude. Combining data on bulk rocks, minerals, and their melt inclusions together with the very first published gas fluxes acquired during the same period of activity, we propose that the high sulfur outgassing in 2009-2010 was produced by the degassing of a basaltic magma batch ( 0.027 km3) emplaced in a shallow reservoir. This scenario would require temperature and H2O-loss driven resorption/crystallization, magma mixing, and exsolution of an early gas phase rich in H2O, and S. We suggest here the 2009-2010 activity to be sustained by the existence of thermal convection driven at the bottom of the magma reservoir by cooling, and in which the bubbles

  1. Arcing phenomena in fusion devices workshop

    Energy Technology Data Exchange (ETDEWEB)

    Clausing, R.E.

    1979-01-01

    The workshop on arcing phenomena in fusion devices was organized (1) to review the pesent status of our understanding of arcing as it relates to confinement devices, (2) to determine what informaion is needed to suppress arcing and (3) to define both laboratory and in-situ experiments which can ultimately lead to reduction of impurities in the plasma caused by arcing. The workshop was attended by experts in the area of vacuum arc electrode phenomena and ion source technology, materials scientists, and both theoreticians and experimentalists engaged in assessing the importance of unipolar arcing in today's tokamaks. Abstracts for papers presented at the workshop are included.

  2. Thermal radiation effect on the extinction properties of electric arcs in HV circuit breakers

    Directory of Open Access Journals (Sweden)

    Ziani Abderrahmane

    2009-01-01

    Full Text Available During the formation of the electric arc at the opening of a high voltage circuit breaker, the generated plasma will be the seat of a very important thermal exchange. Models founded only on conduction and convection thermal transfers don't reproduce the whole thermal exchanges that are governing the extinction process. This paper is devoted to the development of a model of the electric arc extinction in a high voltage circuit breaker taking in account the thermal radiation of the plasma, in addition to the conduction and convection phenomena. The Stefan-Boltzman equation is coupled with the heat equation, and both equations are solved simultaneously in order to follow the evolution of the arc voltage and the conductance of the thermal plasma. The obtained results are found in good agreement with experimental recordings.

  3. Numerical modeling of two-dimensional heat-transfer and temperature-based calibration using simulated annealing optimization method: Application to gas metal arc welding

    Directory of Open Access Journals (Sweden)

    Bjelić Mišo B.

    2016-01-01

    Full Text Available Simulation models of welding processes allow us to predict influence of welding parameters on the temperature field during welding and by means of temperature field and the influence to the weld geometry and microstructure. This article presents a numerical, finite-difference based model of heat transfer during welding of thin sheets. Unfortunately, accuracy of the model depends on many parameters, which cannot be accurately prescribed. In order to solve this problem, we have used simulated annealing optimization method in combination with presented numerical model. This way, we were able to determine uncertain values of heat source parameters, arc efficiency, emissivity and enhanced conductivity. The calibration procedure was made using thermocouple measurements of temperatures during welding for P355GH steel. The obtained results were used as input for simulation run. The results of simulation showed that represented calibration procedure could significantly improve reliability of heat transfer model. [National CEEPUS Office of Czech Republic (project CIII-HR-0108-07-1314 and to the Ministry of Education and Science of the Republic of Serbia (project TR37020

  4. ISEE-3 observations of a viscously-driven plasma sheet: magnetosheath mass and/or momentum transfer?

    Directory of Open Access Journals (Sweden)

    R. T. Mist

    Full Text Available A statistical analysis of data from the ISEE-3 distant tail campaign is presented. We investigate the mechanism driving slow, tailward flows observed in the plasma sheet. The possibility that these slow flows are driven by mass and/or momentum transfer across the distant tail magnetopause is explored. We establish that 40% of these flows could be driven by the transfer of approximately 4% of the magnetosheath momentum flux into the magnetotail. Current understanding of the Kelvin-Helmholtz instability suggests that this figure is consistent with the amount of momentum flux transfer produced by this mechanism. We also consider the possibility that these flows are solely driven by transferring magnetosheath plasma across the magnetopause. We find that there is sufficient mass observed on these field lines for this to be the sole driving mechanism for only 27% of the observed slow flows.

    Key words. Magnetospheric physics (magnetotail boundary layers; plasma convection; plasma sheet

  5. Application of nonlinear dynamic techniques to high pressure plasma jets

    Science.gov (United States)

    Ghorui, S.; Das, A. K.

    2010-02-01

    Arcs and arc plasmas have been known and used for welding, cutting, chemical synthesis and multitude of other industrial applications for more than hundred years. Though a copious source of heat, light and active species, plasma arc is inherently unstable, turbulent and difficult to control. During recent years, primarily driven by the need of new and energy efficient materials processing, various research groups around the world have been studying new and innovative ways of looking at the issues related to arc dynamics, arc stabilization, species non equilibrium, flow and heat transfer in a stabilized arc plasma device. In this context, experimental determination of nature of arc instabilities using tools of non-linear dynamics, theoretical model formulation, prediction of instability behavior under given operating conditions and possible control methods for the observed instabilities in arcs are reviewed. Space selective probing of the zones inside arc plasma devices without disturbing the system is probably the best way to identify the originating zone of instabilities inside such devices. Existence of extremely high temperature and inaccessibility to direct experimentations due to mechanical obstructions make this task extremely difficult. Probing instabilities in otherwise inaccessible inner regions of the torches, using binary gas mixture as plasma gas is a novel technique that primarily rests on a process known as demixing in arcs. Once a binary gas mixture enters the constricted plasma column, the demixing process sets in causing spatial variations for each of the constituent gases depending on the diffusion coefficients and the gradient of the existing temperature field. By varying concentrations of the constituent gases in the feeding line, it is possible to obtain spatial variations of the plasma composition in a desired manner, enabling spatial probing of the associated zones. Detailed compositional description of different zones inside the torch may be

  6. Charge transfer reactions at interfaces between neutral gas and plasma: Dynamical effects and X-ray emission

    Science.gov (United States)

    Provornikova, E.; Izmodenov, V. V.; Lallement, R.

    2012-04-01

    Charge-transfer is the main process linking neutrals and charged particles in the interaction regions of neutral (or partly ionized) gas with a plasma. In this paper we illustrate the importance of charge-transfer with respect to the dynamics and the structure of neutral gas-plasma interfaces. We consider the following phenomena: (1) the heliospheric interface - region where the solar wind plasma interacts with the partly-ionized local interstellar medium (LISM) and (2) neutral interstellar clouds embedded in a hot, tenuous plasma such as the million degree gas that fills the so-called ``Local Bubble". In (1), we discuss several effects in the outer heliosphere caused by charge exchange of interstellar neutral atoms and plasma protons. In (2) we describe the role of charge exchange in the formation of a transition region between the cloud and the surrounding plasma based on a two-component model of the cloud-plasma interaction. In the model the cloud consists of relatively cold and dense atomic hydrogen gas, surrounded by hot, low density, fully ionized plasma. We discuss the structure of the cloud-plasma interface and the effect of charge exchange on the lifetime of interstellar clouds. Charge transfer between neutral atoms and minor ions in the plasma produces X-ray emission. Assuming standard abundances of minor ions in the hot gas surrounding the cold interstellar cloud, we estimate the X-ray emissivity consecutive to the charge transfer reactions. Our model shows that the charge-transfer X-ray emission from the neutral cloud-plasma interface may be comparable to the diffuse thermal X-ray emission from the million degree gas cavity itself.

  7. Characterization of atmospheric pressure H2O/O2 gliding arc plasma for the production of OH and O radicals

    Science.gov (United States)

    Roy, N. C.; Hafez, M. G.; Talukder, M. R.

    2016-08-01

    Atmospheric pressure H 2 O / O 2 gliding arc plasma is generated by a 88 Hz , 6 kV AC power supply. The properties of the produced plasma are investigated by optical emission spectroscopy. The relative intensity, rotational, vibrational, excitation temperatures and electron density are studied as a function of applied voltage, electrode spacing, and oxygen flow rate. The rotational and vibrational temperatures are determined simulating the OH ( A 2 Σ + ( v ″ = 0 ) → X 2 Π ( v ' = 0 ) ) bands with the aid of LIFBASE simulation software. The excitation temperature is obtained from the CuI transition taking non-thermal equilibrium condition into account employing intensity ratio method. The electron density is approximated from the H α Stark broadening using the Voigt profile fitting method. It is observed that the rotational and vibrational temperatures decrease with increasing electrode spacing and O 2 flow rate, but increase with the applied voltage. The excitation temperature is found to increase with increasing applied voltage and O 2 flow rate, but decrease with electrode spacing. The electron density increases with increasing applied voltage while it seems to be in a downward trend with increasing electrode spacing and O 2 flow rate.

  8. Statin and Fibrate Combination Does not Additionally Lower Plasma Cholesteryl Ester Transfer in Type 2 Diabetes Mellitus

    NARCIS (Netherlands)

    de Vries, Rindert; Dikkeschei, Bert D.; Sluiter, Wim J.; Dallinga-Thie, Geesje M.; van Tol, Arie; Dullaart, Robin P. F.

    2012-01-01

    Background: Plasma cholesteryl ester transfer (CET) from high density lipoproteins (HDL) to very low and low density lipoproteins (VLDL+LDL) may predict (subclinical) atherosclerosis. We tested the extent to which plasma CET and cholesterol esterification (EST) are decreased by statin and fibrate

  9. Momentum and heat transfer from lower hybrid antennas to the tokamak edge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, V.; Goniche, M.; Gunn, J.; Petrzilka, V

    2001-02-01

    The momentum and heat transfer from the Lower Hybrid (LH) grill electric field to tokamak edge plasma are derived within the framework of quasi-linear theory. Results are supported by test electron simulations. An LH power loss of the order of 1- 5% of total radiated power is found to occur in an interaction layer of the size of about 0.3 cm in the radial direction limited by electron Landau damping of the LH slow wave. The underlying electron distribution function describing fast electrons generated in both the parallel and anti-parallel (to{sup {yields}} B{sub 0}) directions is approximated by a sum of drifting Maxwellian with and <{delta}v{sup 2}{sub II} > determined here from the test particle simulations. Non-zero momentum transfer from the antenna field not only leads to fast electron beam formation discussed earlier [V. Fuchs, et al., Phys. Plasmas 3, 4023 (1996)], but also causes charge separation in front of the antenna [V. Petrzilka et al., Czech. Journ. Phys. S3, 127 (1999)]. The resulting electric field is calculated for electrons in equilibrium with the ambient plasma an terms which are likely to modify the ion dynamics are identified. (authors)

  10. Evaporation of Droplets in Plasma Spray-Physical Vapor Deposition Based on Energy Compensation Between Self-Cooling and Plasma Heat Transfer

    Science.gov (United States)

    Liu, Mei-Jun; Zhang, Meng; Zhang, Qiang; Yang, Guan-Jun; Li, Cheng-Xin; Li, Chang-Jiu

    2017-08-01

    In the plasma spray-physical vapor deposition process (PS-PVD), there is no obvious heating to the feedstock powders due to the free molecular flow condition of the open plasma jet. However, this is in contrast to recent experiments in which the molten droplets are transformed into vapor atoms in the open plasma jet. In this work, to better understand the heating process of feedstock powders in the open plasma jet of PS-PVD, an evaporation model of molten ZrO2 is established by examining the heat and mass transfer process of molten ZrO2. The results reveal that the heat flux in PS-PVD open plasma jet (about 106 W/m2) is smaller than that in the plasma torch nozzle (about 108 W/m2). However, the flying distance of molten ZrO2 in the open plasma jet is much longer than that in the plasma torch nozzle, so the heating in the open plasma jet cannot be ignored. The results of the evaporation model show that the molten ZrO2 can be partly evaporated by self-cooling, whereas the molten ZrO2 with a diameter heat transfer.

  11. Plasma arc brazing - a low energy joining technology for steel sheets; Plasmalichtbogenloeten - eine energiearme Fuegetechnik fuer Feinblechwerkstoffe

    Energy Technology Data Exchange (ETDEWEB)

    Bouaifi, B.; Draugelates, U.; Helmich, A.; Ouaissa, B. [TU Clausthal, Clausthal-Zellerfeld (Germany)

    2001-07-01

    Mild and high strength steel sheets are comparatively difficult to weld. The heat input in the case of conventional welding processes is too high, so that plasma brazing is an attractive alternative and complementary joining process. One characteristic of the process is the independent input of energy and filler material. In addition, the process is practically spatter-free. Plasma brazing reduces joint and panel distortion and is tolerant to surface contamination and metallic surface coatings. The brazed seams are aesthetic in appearance and clear good mechanical properties. (orig.)

  12. Mathematical model on heat transfer of water-cooling steel-stick bottom electrode of DC electric arc furnace

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    For predicting and controlling the melted depth of bottom electrode during the process of steelmaking, the water-cooling steel-stick electrode is taken as an example, to analyze the process of heat transfer, then 3D mathematical model by control capacity method is built. At the same time, the measurement on the melted depth of bottom electrode is conducted which verified the correctness of the built mathematical model. On the base of verification, all kinds of key parameters are calculated through the application and a series of results are simulated. Finally, the optimum parameters are found and the service lifeof bottom electrode is prolonged.

  13. Nitrogen mass transfer models for plasma-based low-energy ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Bocong; Wang, Kesheng; Zhang, Zhipeng; Che, Honglong; Lei, Mingkai, E-mail: mklei@dlut.edu.cn [Surface Engineering Laboratory, School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024 (China)

    2015-03-15

    The nitrogen mass transfer process in plasma-based low-energy ion implantation (PBLEII) is theoretically and experimentally studied in order to explore the process mechanism of PBLEII and therefore to optimize the apparatus design and the process conditions. An electron cyclotron resonance (ECR) microwave discharge generates the nitrogen plasma with a high density of 10{sup 11}–10{sup 12} ions/cm{sup 3}, which diffuses downstream to the process chamber along the divergent magnetic field. The nitrogen ions in the plasma implant into the surface and transport to the matrix of an austenitic stainless steel under the low negative pulsed bias of −2 kV at a process temperature of 400 °C. A global plasma model is used to simulate the ECR microwave plasma discharge for a range of working pressures and microwave powers. The fluid models are adopted to calculate the plasma downstream diffusion, the sheath expansion and the low-energy ion implantation on the surface. A nonlinear kinetic discrete model is established to describe the nitrogen transport in the austenitic stainless steel and the results are compared with the experimental measurements. Under an average implantation current density of 0.3–0.6 mA/cm{sup 2}, the surface nitrogen concentration in the range from 18.5 to 29 at. % is a critical factor for the nitrogen transport in the AISI 304 austenitic stainless steel by PBLEII, which accelerates the implanted nitrogen diffusion inward up to 6–12 μm during a nitriding time of 4 h.

  14. Beam Transfer Line Design for a Plasma Wakefield Acceleration Experiment (AWAKE) at the CERN SPS

    CERN Document Server

    Bracco, C; Brethoux, D; Clerc, V; Goddard, B; Gschwendtner, E; Jensen, L K; Kosmicki, A; Le Godec, G; Meddahi, M; Muggli, P; Mutin, C; Osborne, O; Papastergiou, K; Pardons, A; Velotti, F M; Vincke, H

    2013-01-01

    The world’s first proton driven plasma wakefield acceleration experiment (AWAKE) is presently being studied at CERN. The experimentwill use a high energy proton beam extracted from the SPS as driver. Two possible locations for installing the AWAKE facility were considered: the West Area and the CNGS beam line. The previous transfer line from the SPS to the West Area was completely dismantled in 2005 and would need to be fully re-designed and re-built. For this option, geometric constraints for radiation protection reasons would limit the maximum proton beam energy to 300 GeV. The existing CNGS line could be used by applying only minor changes to the lattice for the final focusing and the interface between the proton beam and the laser, required for plasma ionisation and bunch-modulation seeding. The beam line design studies performed for the two options are presented.

  15. Anisotropic pattern transfer in ultrananocrystalline diamond films by inductively coupled plasma etching.

    Science.gov (United States)

    Park, Jong Cheon; Kim, Seong Hak; Cha, Seung Uk; Jeong, Geun; Kim, Tae Gyu; Kim, Jin Kon; Cho, Hyun

    2014-12-01

    High density plasma etching of ultrananocrystalline diamond (UNCD) films wasperformed in O2 and O2/Ar inductively coupled plasma (ICP) discharges. The O2/Ar ICP discharges produced higher etch rates due to enhanced physical component of the etching, and a maximum etch rate of -280 nm/min was obtained in 10 sccm O2/5 sccm Ar discharges. Very high etch selectivities up to -140:1 were obtained for the UNCD over Al mask layer. Anisotropic pattern transfer with a vertical sidewall profile was achieved in the 10 sccm O2/5 sccm Ar discharges at a relatively low source power (300 W) and a moderate rf chuck power (200 W).

  16. The diffusion transfer of sputtered atoms in plasma spraying on the internal cylindrical surface

    Energy Technology Data Exchange (ETDEWEB)

    Bondarenko, G.G. [Moscow State University of Electronics and Mathematics, Moscow (Russian Federation); Bonk, O.G.; Kristya, V.I. [Kaluga Branch of N.E. Bauman Moscow University of Technology, Moscow (Russian Federation)

    2001-07-01

    The sputtering of the surface of the solid by the glow discharge plasma is used widely in the electronics for the deposition of thin films. The sputtered atoms (SA), leaving the surface, clash with the gas atoms and the granules the energy. It is interesting to examine the effect of the condensation coefficient of the SA on the concentration of the SA in the cylindrical discharge volume and the fluxes of the SA to different areas of the wall. The solution of this problem for the case of the diffusion transfer of the SA is the subject of this work.

  17. The parametric resonance features for theory of energy transfer in dusty plasma

    Science.gov (United States)

    Semyonov, V. P.; Timofeev, A. V.

    2015-11-01

    One of the mechanisms of energy transfer between degrees of freedom of dusty plasma system can be described by equations similar to Mathieu equation with account of stochastic forces. Such equation is studied by analytical approach. The solutions for higher order of accuracy are obtained. The method for numerical solution and resonance zone detection is proposed. The solution for the extended Mathieu equation is obtained for wide range of parameter values. The results of numerical solution are compared with analytical solutions of different order and known analytical results for Mathieu equation.

  18. Heat Transfer from a dc Laminar Plasma-Jet Flow to Different Solid Surfaces

    Institute of Scientific and Technical Information of China (English)

    孟显; 潘文霞; 吴承康

    2003-01-01

    The heat flux distributions were measured by using transient method for an argon dc laminar plasma-jet flow impinging normally on a plate surface embedded with copper probes. Different powders were coated on the probe surfaces and the effect of powder coatings on the heat transfer from jet flow to the probe surface was examined.Experimental results show that the maximum values of the heat flux to the probe increase with the coating of fine metal powders, while for the surfaces coated with fine ceramic powders, the maximum values of heat flux decrease, compared with that to the bare copper probe surface.

  19. Three-fluid plasmas in star formation II. Momentum transfer rate coefficients

    CERN Document Server

    Pinto, Cecilia

    2008-01-01

    The charged component of the insterstellar medium consists of atomic and molecular ions, electrons, and charged dust grains, coupled to the local Galactic magnetic field. Collisions between neutral particles (mostly atomic or molecular hydrogen) and charged species, and between the charged species themselves, affect the magnetohydrodynamical behaviour of the medium and the dissipation of electric currents. The friction force due to elastic collisions between particles of different species in the multi-component interstellar plasma is a nonlinear function of the temperature of each species and the Mach number of the relative drift velocity. The aim of this paper is to provide an accurate and, as far as possible, complete set of momentum transfer rate coefficients for magnetohydrodynamical studies of the interstellar medium. Momentum transfer rates are derived from available experimental data and theoretical calculations of cross sections within the classic approach developed by Boltzmann and Langevin for a wid...

  20. Fluctuation-induced shear flow and energy transfer in plasma interchange turbulence

    Energy Technology Data Exchange (ETDEWEB)

    Li, B. [School of Physics, State Key Laboratory of Nuclear Physics and Technology, Peking University, Beijing 100871 (China); Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Sun, C. K.; Wang, X. Y.; Zhou, A.; Wang, X. G. [School of Physics, State Key Laboratory of Nuclear Physics and Technology, Peking University, Beijing 100871 (China); Ernst, D. R. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2015-11-15

    Fluctuation-induced E × B shear flow and energy transfer for plasma interchange turbulence are examined in a flux-driven system with both closed and open magnetic field lines. The nonlinear evolution of interchange turbulence shows the presence of two confinement regimes characterized by low and high E × B flow shear. In the first regime, the large-scale turbulent convection is dominant and the mean E × B shear flow is at a relatively low level. By increasing the heat flux above a certain threshold, the increased turbulent intensity gives rise to the transfer of energy from fluctuations to mean E × B flows. As a result, a transition to the second regime occurs, in which a strong mean E × B shear flow is generated.

  1. Topology of magnetic flux ropes and formation of fossil flux transfer events and boundary layer plasmas

    Science.gov (United States)

    Lee, L. C.; Ma, Z. W.; Fu, Z. F.; Otto, A.

    1993-01-01

    A mechanism for the formation of fossil flux transfer events and the low-level boundary layer within the framework of multiple X-line reconnection is proposed. Attention is given to conditions for which the bulk of magnetic flux in a flux rope of finite extent has a simple magnetic topology, where the four possible connections of magnetic field lines are: IMF to MSP, MSP to IMF, IMF to IMF, and MSP to MSP. For a sufficient relative shift of the X lines, magnetic flux may enter a flux rope from the magnetosphere and exit into the magnetosphere. This process leads to the formation of magnetic flux ropes which contain a considerable amount of magnetosheath plasma on closed magnetospheric field lines. This process is discussed as a possible explanation for the formation of fossil flux transfer events in the magnetosphere and the formation of the low-latitude boundary layer.

  2. Mathematical Model on heat transfer of water—cooling steel—stick bottom electrode of DC electric arc furnace

    Institute of Scientific and Technical Information of China (English)

    HaiXu; XiaoLiu; 等

    2002-01-01

    For predicting and controlling the melted depth of bottom electrode during the process of steelmaking,the water-cooling steel stick electrode is taken as an example.to analyze the process of heat transfer,then 3D mathematical model by control capacity method is built.At the same time,the measurement on the melted depth of bottom electrode is conducted which verified the correctness of the built mathematical model.On the base of verification,all kinds of key parameters are calculated through the application and a series of results are simulated.Finally,the optimum parameters are found and the service life of bottom electrode is prolonged.

  3. CO2气体保护焊短路过渡过程与电参数的关系%RELATIONSHIP BETWEEN SHORT CIRCUIT TRANSFER OF CO2 ARC WELDING AND ITS ELECTRIC PARAMETERS

    Institute of Scientific and Technical Information of China (English)

    李桓; 杨立军; 李俊岳; 邓黎丽; 张宝红

    2001-01-01

    用计算机控制的高性能数据采集系统对CO2焊短路过渡过程的电参数进行了研究.分析认为可利用电弧电压来指示熔滴短路及电弧复燃,利用电弧电压的微分来指示液体小桥缩颈,为CO2焊短路过渡实时控制奠定了基础.%The electric parameters of the short-circuit transfer of CO2 arc welding are examined totally and systematically by using an advanced data-collecting system controlled by a computer.Stadies and analysis of the above data show that the arc voltage can reflect the droplet short circuit and the arc re-start,and its differential signal can indicate the pinch of the liquid bridge.This is a better foundation for developing the real-time control of short-circuit transfer of CO2 arc welding.

  4. The refinement of the surface layer of HS 7425 high speed tool steel by laser and electric arc plasma

    Directory of Open Access Journals (Sweden)

    W. Bochnowski

    2008-10-01

    Full Text Available The paper present two different techniques: laser remelting surface and plasma remelting surface of the high speed steel HS 7425. Thestructure of the remelted layers were examined by means of SEM – microscopy. Measurement of microhardness in remelting zone usingVickers method. The remelting zone consist of dendritic cells and columnar crystals. Increase of hardness was observed in remelted zonein comparison to the substrate of the steel. The hardness in the remelted zone increases with the increasing cooling rate.

  5. High-rate and low-temperature growth of ZnO:Ga thin films by steered cathodic arc plasma evaporation

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Chih-Hao [Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan (China); Wang, Wei-Lin [Nano Materials Center, ITRI South, Industrial Technology Research Institute, Tainan, Taiwan (China); Hwang, Weng-Sing, E-mail: wshwang@mail.ncku.edu.tw [Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan (China)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer ZnO:Ga (GZO) films are deposited on glass by steered cathodic arc plasma evaporation. Black-Right-Pointing-Pointer GZO films are grown at a high growth rate (220 nm/min) and low temperature (120 Degree-Sign C). Black-Right-Pointing-Pointer Films with low strain show low resistivity and high transparency. Black-Right-Pointing-Pointer Droplet size is reduced when a high-melting-point GZO ceramic target is adopted. Black-Right-Pointing-Pointer Metal-like conductivity indicates GZO films became degenerated semiconductors. - Abstract: Ga-doped ZnO (GZO) thin films with various thicknesses (120-520 nm) are deposited on the glass substrate at a high growth rate of 220 nm/min and a low temperature of 120 Degree-Sign C by a steered cathodic arc plasma evaporation (steered CAPE). The growth mechanism, microstructure, residual stress, surface morphology, electrical and optical properties, chemical states, electron transport behaviors and thickness effect of the GZO films are investigated. The film stress is gradually relaxed from -0.516 GPa to -0.090 GPa with thickness increasing. Transmission electron microscopy (TEM) images show that the GZO microstructure consists of c-axis textured columnar grains accompanied by some embedded nanodroplets. The droplet size is significantly reduced when a high-melting-point (1975 Degree-Sign C) GZO ceramic target is adopted. High-resolution TEM image shows the GZO crystallites nucleated directly onto the amorphous substrate. The electrical properties improve with increasing thickness. The lowest resistivity (4.72 Multiplication-Sign 10{sup -4} {Omega} cm) is achieved at the thickness of 520 nm, with a corresponding transmittance of 89% in the visible region. Temperature-dependent resistivity measurements show that metal-semiconductor transition temperature increases from 136 K to 225 K when decreasing the thickness, which is due to the increasing the localized states caused by the defects and

  6. Numerical simulation of an atmospheric pressure RF-driven plasma needle and heat transfer to adjacent human skin using COMSOL.

    Science.gov (United States)

    Schröder, Maximilian; Ochoa, Angel; Breitkopf, Cornelia

    2015-06-07

    Plasma medicine is an emerging field where plasma physics is used for therapeutical applications. Temperature is an important factor to take into account with respect to the applications of plasma to biological systems. During the treatment, the tissue temperature could increase to critical values. In this work, a model is presented, which is capable of predicting the skin temperature during a treatment with a radio frequency driven plasma needle. The main gas was helium. To achieve this, a discharge model was coupled to a heat transfer and fluid flow model. The results provide maximum application times for different power depositions in order to avoid reaching critical skin temperatures.

  7. Tailoring the heat transfer on the injection moulding cavity by plasma sprayed ceramic coatings

    Science.gov (United States)

    Bobzin, K.; Hopmann, Ch; Öte, M.; Knoch, M. A.; Alkhasli, I.; Dornebusch, H.; Schmitz, M.

    2017-03-01

    Inhomogeneous material shrinkage in injection moulding can cause warpage in thermoplastic components. To minimise the deformations of the injection moulding parts, the heat transfer during the cooling phase can be adjusted according to the local cooling demand on the surface of the mould cavity by means of plasma sprayed coatings with locally variable thermal resistance over the surface of the mould. Thermal resistance is a function of thermal conductivity and thickness of the coatings, where thermal conductivity of thermal barrier coatings can be adjusted by altering the chemical composition and the microstructure, which is depending on the thickness. This work evaluates the application of plasma sprayed coatings with variable thickness as thermal barrier coatings in the mould cavity. The thermal resistance of the coating and thereby the heat transfer from the melt into the mould will be influenced locally by varying the coating thickness over the cavity area according to the local cooling demand. Using the laser flash method, the thermal conduction of coatings with different thicknesses will be determined. On the basis of the experimentally determined thermal conduction, the effect of the coatings on the temperature field of the mould cavity will be numerically calculated and the required thickness distribution of the coating for an optimal temperature gradient will be determined.

  8. Transfer of deformation in back-arc basins with a laterally variable rheology: Constraints from analogue modelling of the Balkanides-Western Black sea inversion

    NARCIS (Netherlands)

    Munteanu, I.; Willingshofer, E.; Sokoutis, D.; Matenco, L.C.; Dinu, C.; Cloetingh, S.

    2013-01-01

    The balance between extension and contraction in back-arc basins is very sensitive to a number of parameters related to on-going subduction and collision processes. This leads to complex back-arc geometries, where a lateral transition between crustal blocks with contrasting rheologies is often recor

  9. Modeling Vacuum Arcs On Spacecraft Solar Panel Arrays Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Spacecraft charging and subsequent vacuum arcing poses a significant threat to satellites in LEO and GEO plasma conditions. Localized arc discharges can cause a...

  10. Microstructural evolution and mechanical property of Ti-6Al-4V wall deposited by continuous plasma arc additive manufacturing without post heat treatment.

    Science.gov (United States)

    Lin, Jianjun; Lv, Yaohui; Liu, Yuxin; Sun, Zhe; Wang, Kaibo; Li, Zhuguo; Wu, Yixiong; Xu, Binshi

    2017-05-01

    Plasma arc additive manufacturing (PAM) is a novel additive manufacturing (AM) technology due to its big potential in improving efficiency, convenience and being cost-savings compared to other AM processes of high energy bea\\m. In this research, several Ti-6Al-4V thin walls were deposited by optimized weld wire-feed continuous PAM process (CPAM), in which the heat input was gradually decreased layer by layer. The deposited thin wall consisted of various morphologies, which includes epitaxial growth of prior β grains, horizontal layer bands, martensite and basket weave microstructure, that depends on the heat input, multiple thermal cycles and gradual cooling rate in the deposition process. By gradually reducing heat input of each bead and using continuous current in the PAM process, the average yield strength (YS), ultimate tensile strength (UTS) and elongation reach about 877MPa, 968MPa and 1.5%, respectively, which exceed the standard level of forging. The mechanical property was strengthened and toughened due to weakening the aspect ratio of prior β grains and separating nano-dispersoids among α lamellar. Furthermore, this research demonstrates that the CPAM process has a potential to manufacture or remanufacture in AM components of metallic biomaterials without post-processing heat treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Prediction of Welded Joint Strength in Plasma Arc Welding: A Comparative Study Using Back-Propagation and Radial Basis Neural Networks

    Science.gov (United States)

    Srinivas, Kadivendi; Vundavilli, Pandu R.; Manzoor Hussain, M.; Saiteja, M.

    2016-09-01

    Welding input parameters such as current, gas flow rate and torch angle play a significant role in determination of qualitative mechanical properties of weld joint. Traditionally, it is necessary to determine the weld input parameters for every new welded product to obtain a quality weld joint which is time consuming. In the present work, the effect of plasma arc welding parameters on mild steel was studied using a neural network approach. To obtain a response equation that governs the input-output relationships, conventional regression analysis was also performed. The experimental data was constructed based on Taguchi design and the training data required for neural networks were randomly generated, by varying the input variables within their respective ranges. The responses were calculated for each combination of input variables by using the response equations obtained through the conventional regression analysis. The performances in Levenberg-Marquardt back propagation neural network and radial basis neural network (RBNN) were compared on various randomly generated test cases, which are different from the training cases. From the results, it is interesting to note that for the above said test cases RBNN analysis gave improved training results compared to that of feed forward back propagation neural network analysis. Also, RBNN analysis proved a pattern of increasing performance as the data points moved away from the initial input values.

  12. Magnetocaloric properties of TbN, DyN and HoN nanopowders prepared by the plasma arc discharge method.

    Science.gov (United States)

    Shinde, K P; Jang, S H; Kim, J W; Kim, D S; Ranot, M; Chung, K C

    2015-12-21

    We report for the first time the synthesis of nanopowders of TbN, DyN and HoN crystallized in a cubic structure by the plasma arc discharge (PAD) method and investigate their magnetocaloric properties for magnetic refrigeration applications. The nitridization of terbium, dysprosium and holmium was obtained using a mixture of nitrogen and argon gas inside a discharge chamber with 4 kPa pressure. The structural and microstructural properties of these rare earth nitrides were investigated by using X-ray diffraction and transmission electron microscopy. The studied nitrides undergo a second-order ferromagnetic to paramagnetic phase transition at Curie temperatures of 35.7, 19.9 and 14.2 K for TbN, DyN and HoN, respectively. The magnetocaloric effects were estimated by calculating the magnetic entropy changes from the magnetization data sets measured at the different applied magnetic fields and temperatures. The changes in entropy -ΔSM were found to be 12.0, 13.6 and 24.5 J kg(-1) K(-1) at an applied magnetic field of 5 T.

  13. The study of micro-arc discharges during cathodic plasma electrolysis of refractory metals using the spectral line shape of Na I lines

    Science.gov (United States)

    Jovović, Jovica; Stojadinović, Stevan; Tadić, Nenad; Vasilić, Rastko; Šišović, Nikola M.

    2016-03-01

    The micro-arc discharges during cathodic plasma electrolysis of refractory metals (Zr, Ti, Ta) are studied by means of optical emission spectroscopy. The fitting procedure based on three mutually shifted profiles is developed to analyze the complex line shape of Na I 568.64 nm and 615.86 nm doublets. Each profile includes effects of instrumental, Doppler, Stark, van der Waals and resonance broadening. The results show the existence of three discharge zones with electron number density values Ne1=7× 1014 \\text{cm}-3 , Ne2=(0.5\\text{--}1)× 1016 \\text{cm}-3 and Ne3= (1.5\\text{--}2.8)× 1016 \\text{cm}-3 while those of sodium ground-state atoms are Ng1=1.4×1017 \\text{cm}-3 , Ng2=3.6×1017 \\text{cm}-3 and Ng3=(1.7\\text{--}3.7)×1018 \\text{cm}-3 .

  14. Characterization and Optimization of Ni-WC Composite Weld Matrix Deposited by Plasma-Transferred Arc Process

    Science.gov (United States)

    Tahaei, Ali; Horley, Paul; Merlin, Mattia; Torres-Torres, David; Garagnani, Gian Luca; Praga, Rolando; Vázquez, Felipe J. García; Arizmendi-Morquecho, Ana

    2017-03-01

    This work is dedicated to optimization of carbide particle system in a weld bead deposited by PTAW technique over D2 tool steel with high chromium content. The paper reports partial melting of the original carbide grains of the Ni-based filling powder, and growing of the secondary carbide phase (Cr, Ni)_3W_3C in the form of dendrites with wide branches that enhanced mechanical properties of the weld. The optimization of bead parameters was made with design of experiment methodology complemented by a complex sample characterization including SEM, EDXS, XRD, and nanoindentation measurements. It was shown that the preheat of the substrate to a moderate temperature 523 K (250° C) establishes linear pattern of metal flow in the weld pool, resulting in the most homogeneous distribution of the primary carbides in the microstructure of weld bead.

  15. Characterization and Optimization of Ni-WC Composite Weld Matrix Deposited by Plasma-Transferred Arc Process

    Science.gov (United States)

    Tahaei, Ali; Horley, Paul; Merlin, Mattia; Torres-Torres, David; Garagnani, Gian Luca; Praga, Rolando; Vázquez, Felipe J. García; Arizmendi-Morquecho, Ana

    2017-01-01

    This work is dedicated to optimization of carbide particle system in a weld bead deposited by PTAW technique over D2 tool steel with high chromium content. The paper reports partial melting of the original carbide grains of the Ni-based filling powder, and growing of the secondary carbide phase (Cr, Ni)_3 W_3 C in the form of dendrites with wide branches that enhanced mechanical properties of the weld. The optimization of bead parameters was made with design of experiment methodology complemented by a complex sample characterization including SEM, EDXS, XRD, and nanoindentation measurements. It was shown that the preheat of the substrate to a moderate temperature 523 K (250° C) establishes linear pattern of metal flow in the weld pool, resulting in the most homogeneous distribution of the primary carbides in the microstructure of weld bead.

  16. Quelle place pour les arcs \\'electriques et les r\\'eacteurs plasmas dans l'" Inventaire et valorisation des collections, archives scientifiques et biens culturels " de l'universit\\'e de Limoges ?

    CERN Document Server

    Pateyron, Bernard

    2011-01-01

    The University of Limoges in the rehabilitation of the premises was confronted with scientific disposal of property irreplaceable heritage in the context of "postmodern" or "post industrial" of our industrial society. Therefore a "scientific and cultural heritage Mission" was created in 2010 to save as much as possible the memory of the past half-century. For reasons we discuss plasmas and electric arcs have been an important place at that time in Western industry and especially by chance in Limoges.

  17. Simulation of coal conversion in Ar/H{sub 2} plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Y.J.; Chen, H.G.; Bao, W.R.; Li, F.; Zhu, S.Y.; Xie, K.C. [Taiyuan University of Technology, Taiyuan (China). Shanxi Key Lab of Coal Science and Technology

    1999-07-01

    Coal conversion arc plasma was estimated by the combination of energy balance and chemical percolation devolatilization model. The velocity of particles was calculated by momentum equations and the temperature of particles and plasma jet was calculated by heat transfer equations. 11 refs., 2 figs., 4 tabs.

  18. NEW LONGITUDINAL STRENGTHENING METHOD FOR PLASMA ARC POWDER SURFACING COATING%高硬度等离子弧粉末堆焊层的纤维纵向强化

    Institute of Scientific and Technical Information of China (English)

    王惜宝; 张文钺

    2000-01-01

    研究一种用于高硬度等离子弧堆焊层纵向强化的纤维强化法.通过对纤维增强等离子弧堆焊层的制备工艺及纤维加入量对堆焊层纵向断裂韧性的影响研究,发现选择具有高熔点和高强度的W-Mo合金纤维作为堆焊层的增强纤维不仅具有较好的工艺可操作性,而且具有明显的增强作用.在成分(质量分数)为Fe-20% B4C复合粉末等离子弧堆焊层中加入体积分数为4.8%的W-Mo合金纤维,即可使堆焊层的纵向断裂韧性提高33.5%.%A new longitudinal strengthening method for powder surfacing brittle coating using high strength metal fibres has been successfully developed.The preparing process of the fibre-reinforced hardfacing alloys and the effects of fibre's volume fraction on the composite coating's fracture toughness were investigated and analyzed.The results reveal that the high strength and high melting point Mo-W alloy fibres present not only much better processing feasibility than C- and other ceramic-fibres,but also excellent strengthening effect on the brittle coatings.The addition of 4.8% Mo-W fibres (volume fraction)to a Fe-20% B4C (weight fraction)composite plasma transferred-arc powder surfaced coating may improve the coating's longitudinal fracture toughness by 33.5%.

  19. Insulin decreases plasma cholesteryl ester transfer but not cholesterol esterification in healthy subjects as well as in normotriglyceridaemic patients with type 2 diabetes

    NARCIS (Netherlands)

    Dullaart, RPF; Riemens, SC; Scheek, LM; van Tol, A

    1999-01-01

    Background Plasma cholesterol esterification (EST) and subsequent cholesteryl ester transfer (CET) from high-density lipoproteins (HDLs) towards apolipoprotein (apo) B-containing lipoproteins are key steps in HDL metabolism. Materials and methods The effects of exogenous hyperinsulinaemia on plasma

  20. Mechanical and Chemical Characterization of a TiC/C System Synthesized Using a Focus Plasma Arc.

    Directory of Open Access Journals (Sweden)

    Reza Mahmoodian

    Full Text Available Titanium carbide-graphite (TiC/C composite was successfully synthesized from Ti and C starting elemental powders using self-propagating high-temperature synthesis technique in an ultra-high plasma inert medium in a single stage. The TiC was exposed to a high-temperature inert medium to allow recrystallization. The product was then characterized using field emission scanning electron microscopy (FESEM coupled with energy dispersive X-ray analysis (EDX, X-ray diffraction (XRD, Rietveld refinement, nanoindentation, and micro-hardness to determine the product's properties. The recorded micro-hardness of the product was 3660 HV, which is a 14% enhancement and makes is comparable to TiC materials.

  1. Characterization of the behaviour of the electric arc during VAR of a Ti alloy

    Science.gov (United States)

    Chapelle, P.; Noël, C.; Risacher, A.; Jourdan, J.; Jourdan, J.; Jardy, A.

    2016-07-01

    In this paper, we report experimental results based on the direct observation of the electric arc behaviour during vacuum arc remelting of a Ti alloy. These results were obtained in a specifically instrumented industrial furnace using high speed framing camera and optical emission spectroscopy, for a current density level of the order of 10 A/cm2 and a gap length of a few centimetres. It was observed that the arc exhibits a similar operating regime to that described in the literature for the case of Inconel 718 and Zr alloy electrodes. The arc structure corresponds essentially to that of a diffuse metal vapor arc with separate and rapidly moving cathode spots. Several critical parameters of the cathode spots, including their current, size and velocity, and of the interelectrode plasma were evaluated. Also, the interactions between the arc operation and the transfer of metal drops in the interelectrode gap were investigated. Three modes of transfer of the liquid metal drops in the interelectrode gap have been identified depending on the gap length: drop falling, drip short and drop erosion induced by the cathode spots.

  2. Arc Statistics

    CERN Document Server

    Meneghetti, M; Dahle, H; Limousin, M

    2013-01-01

    The existence of an arc statistics problem was at the center of a strong debate in the last fifteen years. With the aim to clarify if the optical depth for giant gravitational arcs by galaxy clusters in the so called concordance model is compatible with observations, several studies were carried out which helped to significantly improve our knowledge of strong lensing clusters, unveiling their extremely complex internal structure. In particular, the abundance and the frequency of strong lensing events like gravitational arcs turned out to be a potentially very powerful tool to trace the structure formation. However, given the limited size of observational and theoretical data-sets, the power of arc statistics as a cosmological tool has been only minimally exploited so far. On the other hand, the last years were characterized by significant advancements in the field, and several cluster surveys that are ongoing or planned for the near future seem to have the potential to make arc statistics a competitive cosmo...

  3. Processing of ash and slag waste of heating plants by arc plasma to produce construction materials and nanomodifiers

    Science.gov (United States)

    Buyantuev, S. L.; Urkhanova, L. A.; Kondratenko, A. S.; Shishulkin, S. Yu; Lkhasaranov, S. A.; Khmelev, A. B.

    2017-01-01

    The resultsare presented of plasma processing slag and ash waste from coal combustion in heating plants. Melting mechanism of ashand slagraw material is considered by an electromagnetic technological reactor. The analysis was conducted of temperature and phase transformations of raw material when it is heated up to the melting point, and also determination of specific energy consumption by using a generalized model of the thermodynamic analysis of TERRA. The study of materials melting temperature conditions and plum of melt was carried with high-temperature thermal imaging method, followed by mapping and 3D-modeling of the temperature fields. The investigations to establish the principal possibilities of using slag waste of local coal as raw material for the production of mineral (ash and slag) fibers found that by chemical composition there are oxides in the following ranges: 45-65% SiO2; 10-25% Al2O3; 10-45% CaO; 5-10% MgO; other minerals (less than 5%). Thus, these technological wastes are principally suitable for melts to produce mineral wool by the plasma method. An analysis of the results shows the melting point of ash and slag waste - 1800-2000 °C. In this case the specific energy consumption of these processes keeps within the limits of 1.1-1.3 kW*h/kg. For comparison it should be noted that the unit cost of electricity in the known high-melting industrial installations 5-6 kW*h/kg. Upon melting ash and slag waste, which contains up to 2-5% of unburned carbon, carbon nanomaterials were discovered.in the form of ultrafine soot accumulating as a plaque on the water-cooled surfaces in the gas cleaning chamber. The process of formation of soot consists in sublimation-desublimation of part of carbon which is in ash and slag, and graphite electrode. Thus, upon melting of ash and slag in the electromagnetic reactor it is possible to obtain melt, and in the subsequent mineral high quality fiber, which satisfies the requirements of normative documents, and

  4. Study of the spray to globular transition in gas metal arc welding: a spectroscopic investigation

    Science.gov (United States)

    Valensi, F.; Pellerin, S.; Castillon, Q.; Boutaghane, A.; Dzierzega, K.; Zielinska, S.; Pellerin, N.; Briand, F.

    2013-06-01

    The gas metal arc welding (GMAW) process is strongly influenced by the composition of the shielding gas. In particular, addition of CO2 increases the threshold current for the transition from unstable globular to more stable spray transfer mode. We report on the diagnostics—using optical emission spectroscopy—of a GMAW plasma in pure argon and in mixtures of argon, CO2 and N2 while operated in spray and globular transfer modes. The spatially resolved plasma parameters are obtained by applying the Abel transformation to laterally integrated emission data. The Stark widths of some iron lines are used to determine both electron density and temperature, and line intensities yield relative contents of neutral and ionized iron to argon. Our experimental results indicate a temperature drop on the arc axis in the case of spray arc transfer. This drop reduces with addition of N2 and disappears in globular transfer mode when CO2 is added. Despite the temperature increase, the electron density decreases with CO2 concentration. The highest concentration of iron is observed in the plasma column upper part (close to the anode) and for GMAW with CO2. Our results are compared with recently published works where the effect of non-homogeneous metal vapour concentration has been taken into account.

  5. Coupled mass transfer through a fluid phase and volume preservation during the hydration of granulite: An example from the Bergen Arcs, Norway

    Science.gov (United States)

    Centrella, Stephen; Austrheim, Håkon; Putnis, Andrew

    2015-11-01

    The Precambrian granulite facies rocks of Lindås Nappe, Bergen Arcs, Caledonides of W. Norway are partially hydrated at amphibolite and eclogite facies conditions. The Lindås Nappe outcrops over an area of ca. 1000 km2 where relict granulite facies lenses make up only ca. 10%. At Hillandsvatnet, garnetite displays sharp hydration fronts across which the granulite facies assemblage composed of garnet (55%) and clinopyroxene (45%) is replaced by an amphibolite facies mineralogy defined by chlorite, epidote and amphibole. The major element bulk composition does not change significantly across the hydration front, apart from the volatile components (loss on ignition, LOI) that increases from 0.17 wt.% in the granulite to 2.43 wt.% in the amphibolite. However the replacements of garnet and of clinopyroxene are pseudomorphic so that the grain shapes of the garnet and clinopyroxene are preserved even when they are completely replaced. The textural evolution during the replacement of garnet by pargasite, epidote and chlorite and of pyroxene by hornblende and quartz in our rock sample conforms to that expected by a coupled dissolution-precipitation mechanism. SEM and electron microprobe analysis coupled with the software XMapTools V 1.06.1 were used to quantify the local mass transfer required during the replacement processes. The element losses and gains in replacing the garnet are approximately balanced by the opposite gains and losses associated with the replacement of clinopyroxene. The coupling between dissolution and precipitation on both the grain and whole rock spatial scale preserves the volume of the rock throughout the hydration process. However, the hydration involves reduction of rock density and mass balance calculations, together with volume preservation (isovolumetric reaction) require a significant loss of the mass of the rock to the fluid phase. This suggests a mechanism for coupling between the local stress generated by hydration reactions and mass

  6. Impact of ns-DBD plasma actuation on the boundary layer transition using convective heat transfer measurements

    Science.gov (United States)

    Ullmer, Dirk; Peschke, Philip; Terzis, Alexandros; Ott, Peter; Weigand, Bernhard

    2015-09-01

    This paper demonstrates that the impact of nanosecond pulsed dielectric barrier discharge (ns-DBD) actuators on the structure of the boundary layer can be investigated using quantitative convective heat transfer measurements. For the experiments, the flow over a flat plate with a C4 leading edge thickness distribution was examined at low speed incompressible flow (6.6-11.5 m s-1). An ns-DBD plasma actuator was mounted 5 mm downstream of the leading edge and several experiments were conducted giving particular emphasis on the effect of actuation frequency and the freestream velocity. Local heat transfer distributions were measured using the transient liquid crystal technique with and without plasma activated. As a result, any effect of plasma on the structure of the boundary layer is interpreted by local heat transfer coefficient distributions which are compared with laminar and turbulent boundary layer correlations. The heat transfer results, which are also confirmed by hot-wire measurements, show the considerable effect of the actuation frequency on the location of the transition point elucidating that liquid crystal thermography is a promising method for investigating plasma-flow interactions very close to the wall. Additionally, the hot-wire measurements indicate possible velocity oscillations in the near wall flow due to plasma activation.

  7. ISEE-3 observations of a viscously-driven plasma sheet: magnetosheath mass and/or momentum transfer?

    Science.gov (United States)

    Mist, R. T.; Owen, C. J.

    2002-05-01

    A statistical analysis of data from the ISEE-3 distant tail campaign is presented. We investigate the mechanism driving slow, tailward flows observed in the plasma sheet. The possibility that these slow flows are driven by mass and/or momentum transfer across the distant tail magnetopause is explored. We establish that 40% of these flows could be driven by the transfer of approximately 4% of the magnetosheath momentum flux into the magnetotail. Current understanding of the Kelvin-Helmholtz instability suggests that this figure is consistent with the amount of momentum flux transfer produced by this mechanism. We also consider the possibility that these flows are solely driven by transferring magnetosheath plasma across the magnetopause. We find that there is sufficient mass observed on these field lines for this to be the sole driving mechanism for only 27% of the observed slow flows.

  8. A new criterion to describe crossed-beam energy transfer in laser-plasma interactions

    Science.gov (United States)

    Trines, R.; Schmitz, H.; Alves, E. P.; Fiuza, F.; Vieira, J.; Silva, L. O.; Bingham, R.

    2016-10-01

    Crossed-beam energy transfer (CBET) between laser beams in underdense plasma is ubiquitous in both direct-drive and indirect-drive inertial confinement fusion. To understand the impact of this process on the final shape of the laser beams involved, as well as their imprint on either hohlraum walls or target surface, a detailed spatial and temporal description of the crossing beams is needed. We have developed an analytical model and derived new criteria describing both the spatial structure and temporal evolution of the beams after crossing. Numerical simulations have been carried out justifying the analytical model and confirming the criteria. The impact of our results on present and future multi-beam experiments in laser fusion and high-energy-density physics, in particular the ``bursty'' nature of beams predicted to occur in NIF experiments, will be discussed.

  9. ISEE-3 observations of a viscously-driven plasma sheet: magnetosheath mass and/or momentum transfer?

    OpenAIRE

    Mist, R. T.; Owen, C.J.

    2002-01-01

    A statistical analysis of data from the ISEE-3 distant tail campaign is presented. We investigate the mechanism driving slow, tailward flows observed in the plasma sheet. The possibility that these slow flows are driven by mass and/or momentum transfer across the distant tail magnetopause is explored. We establish that 40% of these flows could be driven by the transfer of approximately 4% of the magnetosheath momentum flux into the magnetotail. Current understanding of the Kelvin-Helmholtz in...

  10. ISEE-3 observations of a viscously-driven plasma sheet: magnetosheath mass and/or momentum transfer?

    OpenAIRE

    Mist, R. T.; Owen, C.J.

    2002-01-01

    A statistical analysis of data from the ISEE-3 distant tail campaign is presented. We investigate the mechanism driving slow, tailward flows observed in the plasma sheet. The possibility that these slow flows are driven by mass and/or momentum transfer across the distant tail magnetopause is explored. We establish that 40% of these flows could be driven by the transfer of approximately 4% of the magnetosheath momentum flux into the magnetotail. Current understanding of the Kelvin-Helmh...

  11. Simulating Time-Dependent Energy Transfer Between Crossed Laser Beams in an Expanding Plasma

    Energy Technology Data Exchange (ETDEWEB)

    Hittinger, J F; Dorr, M R; Berger, R L; Williams, E A

    2004-10-11

    A coupled mode system is derived to investigate a three-wave parametric instability leading to energy transfer between co-propagating laser beams crossing in a plasma flow. The model includes beams of finite width refracting in a prescribed transverse plasma flow with spatial and temporal gradients in velocity and density. The resulting paraxial light equations are discretized spatially with a Crank-Nicholson-type scheme, and these algebraic constraints are nonlinearly coupled with ordinary differential equations in time that describe the ion acoustic response. The entire nonlinear differential-algebraic system is solved using an adaptive, backward-differencing method coupled with Newton's method. A numerical study is conducted in two dimensions that compares the intensity gain of the fully time-dependent coupled mode system with the gain computed under the further assumption of a strongly-damped ion acoustic response. The results demonstrate a time-dependent gain suppression when the beam diameter is commensurate with the velocity gradient scale length. The gain suppression is shown to depend on time-dependent beam refraction and is interpreted as a time-dependent frequency shift.

  12. Surface modification of tube inner wall by transferred atmospheric pressure plasma

    Science.gov (United States)

    Chen, Faze; Liu, Shuo; Liu, Jiyu; Huang, Shuai; Xia, Guangqing; Song, Jinlong; Xu, Wenji; Sun, Jing; Liu, Xin

    2016-12-01

    Tubes are indispensable in our daily life, mechanical engineering and biomedical fields. However, the practical applications of tubes are sometimes limited by their poor wettability. Reported herein is hydrophilization of the tube inner wall by transferred atmospheric pressure plasma (TAPP). An Ar atmospheric pressure plasma jet (APPJ) is used to induce He TAPP inside polytetrafluoroethylene (PTFE) tube to perform inner wall surface modification. Optical emission spectrum (OES) is used to investigate the distribution of active species, which are known as enablers for surface modification, along the TAPP. Tubes' surface properties demonstrate that after TAPP treatment, the wettability of the tube inner wall is well improved due to the decrease of surface roughness, the removal of surface fluorine and introduction of oxygen. Notably, a deep surface modification can significantly retard the aging of the obtained hydrophilicity. The results presented here clearly demonstrate the great potential of TAPP for surface modification of the inner wall of tube or other hollow bodies, and thus a uniform, effective and long-lasting surface modification of tube with any length can be easily realized by moving the tube along its axis.

  13. Low voltage arc formation in railguns

    Science.gov (United States)

    Hawke, Ronald S.

    1987-01-01

    A low voltage plasma arc is first established across the rails behind the projectile by switching a low voltage high current source across the rails to establish a plasma arc by vaporizing a fuse mounted on the back of the projectile, maintaining the voltage across the rails below the railgun breakdown voltage to prevent arc formation ahead of the projectile. After the plasma arc has been formed behind the projectile a discriminator switches the full energy bank across the rails to accelerate the projectile. A gas gun injector may be utilized to inject a projectile into the breech of a railgun. The invention permits the use of a gas gun or gun powder injector and an evacuated barrel without the risk of spurious arc formation in front of the projectile.

  14. 大气电弧等离子体技术在熔石英表面加工中的应用%Application of Atmospheric Pressure Plasma Arc Jet in Machining of Fused Silicon Surface

    Institute of Scientific and Technical Information of China (English)

    惠迎雪; 程媛; 刘卫国; 郝飞霞

    2014-01-01

    为了快速获得无亚表面损伤光学表面,提出了一种新型的大气电弧射流等离子体加工方法,该方法的装置采用转移弧电弧放电原理产生大气射流等离子体,通过调节改变喷枪的气压及几何结构,对束斑的尺寸及能量密度进行调节,同时基于其束斑高能离子的物理效应,研究了大气条件下熔石英表面材料的加工工艺.实验结果表明:当采用等离子体喷枪嘴孔径2.5mm,作用距离为2.0mm时,对熔石英的峰值去除速率可达到82.9μm·min-1,单次抛光后,元件表面粗糙度 Ra 值由237 nm下降到103 nm .%In order to machine defect free fused silicon with high efficiency ,a novel type of atmospheric plasma arc jet was developed .The atmospheric plasma jet was produced by gliding arc discharge ,the sizes and density distributions of plasma arc jet can be adjusted by controlling gas pressure and structure of jet nozzle .A physical etching with plasma arc jet was utilized to investigate the plasma machining process of fused silicon at atmospheric pressure .The results showed :The maximum removal rate can reach 82 .9μm · min-1 using the jet nozzle of diameter 2 .5 mm when the working distance was 2 .0 mm .The roughness of the machined surface of single pass of plasma jet decreased from Ra 237 nm of the non-machined surface to 103 nm .

  15. Optical diagnostics of a gliding arc

    DEFF Research Database (Denmark)

    Sun, Z.W.; Zhu, J.J.; Li, Z.S.;

    2013-01-01

    Dynamic processes in a gliding arc plasma generated between two diverging electrodes in ambient air driven by 31.25 kHz AC voltage were investigated using spatially and temporally resolved optical techniques. The life cycles of the gliding arc were tracked in fast movies using a high-speed camera...

  16. Plasma phospholipid transfer protein activity is independently determined by obesity and insulin resistance in non-diabetic subjects

    NARCIS (Netherlands)

    de Vries, Rindert; Kappelle, Paul J.W.H.; Dallinga-Thie, Geesje M.; Dullaart, Robin P. F.

    2011-01-01

    Background: Phospholipid transfer protein (PLTP) is an emerging cardio-metabolic risk factor which is intricately involved in lipoprotein metabolism. Elevated plasma PLTP activity levels are reported in obesity and diabetes mellitus, but the relative contributions of obesity and insulin resistance t

  17. Plasma phospholipid transfer protein activity is independently determined by obesity and insulin resistance in non-diabetic subjects

    NARCIS (Netherlands)

    de Vries, Rindert; Kappelle, Paul J.W.H.; Dallinga-Thie, Geesje M.; Dullaart, Robin P. F.

    2011-01-01

    Background: Phospholipid transfer protein (PLTP) is an emerging cardio-metabolic risk factor which is intricately involved in lipoprotein metabolism. Elevated plasma PLTP activity levels are reported in obesity and diabetes mellitus, but the relative contributions of obesity and insulin resistance t

  18. Plasma phospholipid transfer protein activity is independently determined by obesity and insulin resistance in non-diabetic subjects

    NARCIS (Netherlands)

    de Vries, Rindert; Kappelle, Paul J.W.H.; Dallinga-Thie, Geesje M.; Dullaart, Robin P. F.

    Background: Phospholipid transfer protein (PLTP) is an emerging cardio-metabolic risk factor which is intricately involved in lipoprotein metabolism. Elevated plasma PLTP activity levels are reported in obesity and diabetes mellitus, but the relative contributions of obesity and insulin resistance

  19. High plasma cholesteryl ester transfer protein levels may favour reduced incidence of cardiovascular events in men with low triglycerides

    NARCIS (Netherlands)

    Borggreve, Susanna E.; Hillege, Hans L.; Dallinga-Thie, Geesje M.; de Jong, Paul E.; Wolffenbuttel, Bruce H. R.; Grobbee, Diederik E.; van Tol, Arie; Dullaart, Robin P. F.

    2007-01-01

    Aims High cholesteryl ester transfer protein (CETP) concentrations are associated with increased risk of cardiovascular disease (CVD) in subjects with high triglycerides. We determined the relationship of plasma CETP with incident CVD in a population with relatively low triglycerides. Methods and re

  20. High plasma cholesteryl ester transfer protein levels may favour reduced incidence of cardiovascular events in men with low triglycerides

    NARCIS (Netherlands)

    Borggreve, Susanna E.; Hillege, Hans L.; Dallinga-Thie, Geesje M.; de Jong, Paul E.; Wolffenbuttel, Bruce H. R.; Grobbee, Diederik E.; van Tol, Arie; Dullaart, Robin P. F.

    Aims High cholesteryl ester transfer protein (CETP) concentrations are associated with increased risk of cardiovascular disease (CVD) in subjects with high triglycerides. We determined the relationship of plasma CETP with incident CVD in a population with relatively low triglycerides. Methods and

  1. RESEARCH ON ELECTRIC ARC REDUCTION OF CARBON DIOXIDE,

    Science.gov (United States)

    CARBON DIOXIDE , REDUCTION(CHEMISTRY), ELECTRIC ARCS, CHEMICAL REACTIONS, HEAT OF REACTION, GAS FLOW, OXYGEN, CARBON COMPOUNDS, MONOXIDES, ELECTRODES, LABORATORY EQUIPMENT, HIGH TEMPERATURE, PLASMAS(PHYSICS), ENERGY.

  2. Plasma cholesteryl ester transfer is a determinant of intima-media thickness in type 2 diabetic and nondiabetic subjects : Role of CETP and triglycerides

    NARCIS (Netherlands)

    de Vries, R; Perton, FG; Dallinga-Thie, GM; van Roon, AM; Wolffenbuttel, BHR; van Tol, A; Dullaart, RPF

    2005-01-01

    We tested whether carotid artery intima-media thickness (IMT) is associated with plasma cholesteryl ester transfer (CET) and/or the plasma cholesteryl ester transfer protein (CETP) concentration in type 2 diabetic and control subjects. In 87 male and female subjects with type 2 diabetes (nonsmokers,

  3. Plasma cholesteryl ester transfer is a determinant of intima-media thickness in type 2 diabetic and nondiabetic subjects : Role of CETP and triglycerides

    NARCIS (Netherlands)

    de Vries, R; Perton, FG; Dallinga-Thie, GM; van Roon, AM; Wolffenbuttel, BHR; van Tol, A; Dullaart, RPF

    2005-01-01

    We tested whether carotid artery intima-media thickness (IMT) is associated with plasma cholesteryl ester transfer (CET) and/or the plasma cholesteryl ester transfer protein (CETP) concentration in type 2 diabetic and control subjects. In 87 male and female subjects with type 2 diabetes (nonsmokers,

  4. Plasma cholesteryl ester transfer is a determinant of intima-media thickness in type 2 diabetic and nondiabetic subjects: Role of CETP and triglycerides

    NARCIS (Netherlands)

    R. de Vries (Rindert); F.G. Perton (Frank G.); G.M. Dallinga-Thie (Geesje); A.M.M. van Roon (Arie); B.H.R. Wolffenbuttel (Bruce); A. van Tol (Arie); R.P.F. Dullaart (Robin)

    2005-01-01

    textabstractWe tested whether carotid artery intima-media thickness (IMT) is associated with plasma cholesteryl ester transfer (CET) and/or the plasma cholesteryl ester transfer protein (CETP) concentration in type 2 diabetic and control subjects. In 87 male and female subjects with type 2 diabetes

  5. Gas influence on the arc shape in MIG-MAG welding

    Science.gov (United States)

    Zielinska, S.; Pellerin, S.; Valensi, F.; Dzierzega, K.; Musiol, K.; de Izarra, Ch.; Briand, F.

    2008-07-01

    Composition of the applied shielding gas has a strong influence on physical properties of the plasma and parameters of the welding process. In particular, increase of the percentage of carbon dioxide in argon results in an increase of the transition current value while changing from the globular to spray mode of metal transfer during the welding process. In order to explain this phenomenon, the MIG/MAG welding arc plasma was investigated for different mixtures of argon and carbon dioxide in the shielding gas. Applying a fast camera, recording distribution of spectral lines of the plasma components, we noticed some phenomena not described yet in the literature. Especially, there is a limit in the percentage of relative concentration CO2/Ar beyond which the arc shape is significantly modified.

  6. Elevated plasma cholesteryl ester transfer in NIDDM : relationships with apolipoprotein B-containing lipoproteins and phospholipid transfer protein

    NARCIS (Netherlands)

    Riemens, S; van Tol, A; Sluiter, W; Dullaart, R

    1998-01-01

    Lecithin:cholesteryl acyl transferase (LCAT) and cholesteryl ester transfer protein (CETP) are key factors in the esterification of cholesterol and the subsequent transfer of cholesteryl ester from high density lipoproteins (HDL) towards very low and low density lipoproteins (VLDL + LDL). Phospholip

  7. Research on the Inverter Air-plasma Cutting Machine of LF Contact Pilot Arc%逆变式空气等离子切割机低频引弧技术的研究

    Institute of Scientific and Technical Information of China (English)

    孙强; 刘延明

    2011-01-01

    研制了一种全数字化控制的新型逆变式空气等离子切割机.该等离子机采用非高频的引弧技术,有效地解决了传统技术中存在的高电磁干扰、引弧电路复杂、引弧成功率低等问题.设计以高性能数字信号处理器DSP2812作为主控制芯片,通过理论分析、计算与仿真、控制算法的改进等措施,解决了低频引弧技术中的问题.实验结果表明,该机具有可靠性高、电磁干扰小、一次引弧成功率高等特点.%The digital control system for air-plasma cutting inverter power supply has developed.This cutting machine based on low frequency contact pilot arc and has successfully solved the plenty of short-comings in conventional contact pilot arc technique, such as high electronic magnetic interference (EMI), complex circuit and lower successful ratio of pilot arc and so on.The high performance DSP2812 is utilized as the mainly control chip.By theory analyse, calculate and simulation, the difficulty in low frequency contact pilot arc has been solved.The experimental results verify that the power supply system has higher stability, lower EMI and higher successful ratio of pilot arc.

  8. Turbulent energy transfer in electromagnetic turbulence: hints from a Reversed Field Pinch plasma

    Science.gov (United States)

    Vianello, N.; Bergsaker, H.

    2005-10-01

    The relationship between electromagnetic turbulence and sheared plasma flow in a Reversed Field Pinch is addressed. ExB sheared flows and turbulence at the edge tends to organize themeselves near marginal stability, suggesting an underlying energy exchange process between turbulence and mean flow. In MHD this process is well described through the quantity P which represents the energy transfer (per mass and time unit) from turbulence to mean fields. In the edge region of RFP configuration, where magnetic field is mainly poloidal and the mean ExB is consequently toroidal, the quantity P results: P =[ -ρμ0 + ]Vφr where Vφ is the mean ExB toroidal flow, ρ the mean mass density and b and v the fluctuations of velocity and magnetic field respectively. Both the radial profiles and the temporal evolution of P have been measured in the edge region of Extrap-T2R Reversed Field Pinch experiment. The results support the existence of oscillating energy exchange process between fluctuations and mean flow.

  9. Catalytic property of an indium-deposited powder-type material containing silicon and its dependence on the dose of indium nano-particles irradiated by a pulse arc plasma process

    Directory of Open Access Journals (Sweden)

    Satoru Yoshimura

    2017-06-01

    Full Text Available Indium nano-particle irradiations onto zeolite powders were carried out using a pulse arc plasma source system. X-ray photoelectron spectroscopic and scanning electron microscopic studies of an indium irradiated zeolite sample revealed that indium nano-particles were successfully deposited on the sample. Besides, the sample was found to be capable of catalyzing an organic chemical reaction (i.e., Friedel-Crafts alkylation. Then, we examined whether or not the catalytic ability depends on the irradiated indium dose, having established the optimal indium dose for inducing the catalytic effect.

  10. 圆弧形三角翼翅片管换热器流动与传热特性的数值模拟%Flow and Heat-transfer Characteristics of Finned Tube Heat Exchanger with Arc Delta Winglets

    Institute of Scientific and Technical Information of China (English)

    苏石川; 李光琛; 陈明华; 张旭; 王浩东

    2013-01-01

    3D numerical simulations were performed to investigate the flow and heat transfer coupling characteristics of finned tube heat exchangers with arc or straight delta-winglet vortex generators. Results show that when the Re is in 500-5 000, both the arc and straight delta winglets can enhance the heat transfer of heat exchanger. The enhancement effect of arc delta winglet is slightly weaker than the straight one, but its flow resistance is obviously smaller. In comparison with straight delta-winglet exchanger, the comprehensive performance of arc delta-winglet exchanger is 7. 3%-H. 5% and 8. 2%-9. 5% higher respectively in the case of aligned and staggered arrangement of heat-exchanger tube. The vortex generator can enable fluid to generate a velocity component perpendicular to the fin direction and improve the cooperativity between velocity filed and temperature field, and therefore the heat-transfer performance is enhanced.%采用三维数值模拟方法对加装圆弧形三角翼和直三角翼涡流发生器的翅片管换热器的流动与传热耦合特性进行了研究.结果表明:Re在500~5 000时,圆弧形三角翼和直三角翼均可以提高换热器的传热能力,圆弧形三角翼强化传热的效果略低于直三角翼,但其流动阻力明显小于直三角翼;换热管顺排布置时,圆弧形三角翼换热器的综合性能比直三角翼提高了7.3%~11.5%;换热管叉排布置时,圆弧形三角翼换热器的综合性能比直三角翼提高了8.2%~9.5%;涡流发生器可以使流体产生垂直于翅片方向的速度分量,改善流场中速度场和温度场的协同性,从而增强传热能力.

  11. Supersonic Vortex Gerdien Arc with Magnetic Thermal Insulation

    Science.gov (United States)

    Winterberg, F.

    1988-02-01

    Temperatures up to ~ 5 x 104 oK have been obtained with water vortex Gerdien arcs, and temperatures of ~ 105oK have been reached in hydrogen plasma arcs with magnetic thermal insulation through an externally applied strong magnetic field. It is suggested that a further increase in arc temperatures up to 106oK can conceivably be attained by a combination of both techniques, using a Gerdien arc with a supersonic hydrogen gas vortex.

  12. Modeling of plasma and thermo-fluid transport in hybrid welding

    Science.gov (United States)

    Ribic, Brandon D.

    Hybrid welding combines a laser beam and electrical arc in order to join metals within a single pass at welding speeds on the order of 1 m min -1. Neither autonomous laser nor arc welding can achieve the weld geometry obtained from hybrid welding for the same process parameters. Depending upon the process parameters, hybrid weld depth and width can each be on the order of 5 mm. The ability to produce a wide weld bead increases gap tolerance for square joints which can reduce machining costs and joint fitting difficulty. The weld geometry and fast welding speed of hybrid welding make it a good choice for application in ship, pipeline, and aerospace welding. Heat transfer and fluid flow influence weld metal mixing, cooling rates, and weld bead geometry. Cooling rate affects weld microstructure and subsequent weld mechanical properties. Fluid flow and heat transfer in the liquid weld pool are affected by laser and arc energy absorption. The laser and arc generate plasmas which can influence arc and laser energy absorption. Metal vapors introduced from the keyhole, a vapor filled cavity formed near the laser focal point, influence arc plasma light emission and energy absorption. However, hybrid welding plasma properties near the opening of the keyhole are not known nor is the influence of arc power and heat source separation understood. A sound understanding of these processes is important to consistently achieving sound weldments. By varying process parameters during welding, it is possible to better understand their influence on temperature profiles, weld metal mixing, cooling rates, and plasma properties. The current literature has shown that important process parameters for hybrid welding include: arc power, laser power, and heat source separation distance. However, their influence on weld temperatures, fluid flow, cooling rates, and plasma properties are not well understood. Modeling has shown to be a successful means of better understanding the influence of

  13. BASIC THEORY AND METHOD OF WELDING ARC SPECTRAL INFORMATION

    Institute of Scientific and Technical Information of China (English)

    Li Junyue; Li Zhiyong; Li Huan; Xue Haitao

    2004-01-01

    Arc spectral information is a rising information source which can solve many problems that can not be done with arc electric information and other arc information.It is of important significance to develop automatic control technique of welding process.The basic theory and methods on it play an important role in expounding and applying arc spectral information.Using concerned equation in plasma physics and spectrum theory,a system of equations including 12 equations which serve as basic theory of arc spectral information is set up.Through analyzing of the 12 equations,a basic view that arc spectral information is the reflection of arc state and state variation,and is the most abundant information resource reflecting welding arc process is drawn.Furthermore,based on the basic theory,the basic methods of test and control of arc spectral information and points out some applications of it are discussesed.

  14. Influence of metal vapour on arc temperatures in gas-metal arc welding: convection versus radiation

    Science.gov (United States)

    Murphy, Anthony B.

    2013-06-01

    The presence of metal vapour in gas-metal arc welding has been shown to have two strong effects on the arc plasma: a decrease in temperature throughout the arc, and the formation of a local temperature minimum near the arc axis. These effects have been attributed, on the basis of different computational models, to either the increased radiative emission associated with the presence of metal vapour in the arc plasma, or the influence of the metal vapour influx on convective flow in the arc. This question is investigated using a three-dimensional computational model in which the production and the transport of metal vapour are taken into account self-consistently. Parameters relevant to welding of thin sheets of aluminum are examined. For these conditions, it is found that the first effect (the decrease in temperature throughout the arc) is due to both the increased radiative emission and the influence of the metal vapour influx on flow. The second effect (the local temperature minimum, which in this case occurs just below the wire electrode) is a consequence of the influence of aluminum vapour produced from the wire electrode on flow in the arc. By examining published results and the energy balance in the plasma, it is shown that for welding of steel with higher arc currents, the increased radiative emission can lead to a local temperature minimum at a greater distance from the wire electrode.

  15. Effect of ultrasound on plasma arc and experimental research on welding%超声对等离子电弧的影响及焊接试验研究

    Institute of Scientific and Technical Information of China (English)

    范成磊; 谢伟峰; 杨春利; 林三宝; 孙清洁; 范阳阳

    2015-01-01

    With the development of modern industry, the application of ultrasound in materials processing is getting more and more widespread and important. There are many ultrasonund-welding methods, all of those have improved welding quality and production efficiency to a certain degree, and enhance the adaptability of welding. An ultrasonic-arc technique, utilizing external ultrasonic source to regulate plasma arc (welding heat source), is described in detail in this paper. The arc test shows that the shape of the arc modulated by ultrasound is conical instead of bell-shaped, and this compression effect is very obvious. While in the welding test, with ultrasound, the size of welding droplet is smaller than that without ultrasound, and the transition frequency is significantly increased. By using this method, some of the shortcomings in ordinary arc welding can be overcomed, such as arc energy divergence, the low quality of welds and low welding efficiency.%随着现代工业生产技术的发展,超声波在材料加工领域应用越来越广泛,相继出现了多种超声波与焊接相结合的方式,在一定程度上提高了焊接质量和生产效率,增强了焊接的适应性。详细介绍了一种超声电弧技术,即利用外加超声源调控等离子电弧作为相应热源进行焊接的技术。电弧试验研究显示,受超声调制的等离子电弧呈规则的圆锥形,压缩明显,电弧中心区压力增大。在焊接试验中,发现施加超声后,焊接熔滴尺寸更小,过渡频率明显增加,焊缝的熔宽和熔深都不同程度增加。利用该方法可以克服普通电弧焊接熔深浅、电弧能量不集中、焊接效率低等缺点。

  16. Investigations of GMAW plasma by optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Zielinska, S [Instytut Fizyki im. Mariana Smoluchowskiego, Uniwersytet Jagiellonski, ulica Reymonta 4, 30-059 Krakow (Poland); Musiol, K [Instytut Fizyki im. Mariana Smoluchowskiego, Uniwersytet Jagiellonski, ulica Reymonta 4, 30-059 Krakow (Poland); Dzierzega, K [Instytut Fizyki im. Mariana Smoluchowskiego, Uniwersytet Jagiellonski, ulica Reymonta 4, 30-059 Krakow (Poland); Pellerin, S [LASEP, Faculte des Sciences-Bourges, Universite d' Orleans, BP 4043, 18028 Bourges Cedex (France); Valensi, F [LASEP, Faculte des Sciences-Bourges, Universite d' Orleans, BP 4043, 18028 Bourges Cedex (France); Izarra, Ch de [LASEP, Faculte des Sciences-Bourges, Universite d' Orleans, BP 4043, 18028 Bourges Cedex (France); Briand, F [CTAS - Air Liquide Welding, Rue des Epluches, Saint Ouen l' Aumone (France)

    2007-11-15

    We report on investigations of gas metal arc welding plasma operated in pure argon and in a mixture of argon and CO{sub 2} at a dc current of 326 A. The spatially resolved electron densities and temperatures were directly obtained by measuring the Stark widths of the Ar I 695.5 nm and Fe I 538.3 nm spectral lines. Our experimental results show a reduction of the plasma conductivity and transfer from spray arc to globular arc operation with increasing CO{sub 2} concentration. Although the electron density n{sub e} increases while approaching the core of the plasma in the spray-arc mode, a drop in the electron temperature T{sub e} is observed. Moreover, the maximum T{sub e} that we measure is about 13 000 K. Our experimental results differ from the Haidar model where T{sub e} is always maximum on the arc axis and its values exceed 20 000 K. These discrepancies can be explained as a result of underestimation of the amount of metal vapours in the plasma core and of the assumption of local thermal equilibrium plasma in the model.

  17. Prebeta-migrating high density lipoprotein: quantitation in normal and hyperlipidemic plasma by solid phase radioimmunoassay following electrophoretic transfer

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, B.Y.; Frolich, J.; Fielding, C.J.

    1987-07-01

    A quantitative solid phase immunoassay has been developed for the determination of the mass of electrophoretically separated prebeta apolipoprotein A-I (apoA-I) in human plasma. Conditions have been identified for the quantitative transfer and immunoblotting of the apolipoprotein in the absence of organic solvents or detergents. In normolipidemic plasma, the prebeta-migrating fraction of apoA-I represented 4.2 +/- 1.8% of total apoA-I (61 +/- 26 micrograms of apoA-I per ml of plasma). Significantly higher levels were found in hypercholesterolemia of genetic origin, in primary and secondary hypertriglyceridemia, and in congenital lecithin:cholesterol acyltransferase deficiency. In all cases prebeta-migrating apoA-I consisted in large part of low molecular weight lipoprotein species, compared to the size of the major, alpha-migrating apoA-I fraction.

  18. Laser-energy transfer and enhancement of plasma waves and electron beams by interfering high-intensity laser pulses.

    Science.gov (United States)

    Zhang, P; Saleh, N; Chen, S; Sheng, Z M; Umstadter, D

    2003-11-28

    The effects of interference due to crossed laser beams were studied experimentally in the high-intensity regime. Two ultrashort (400 fs), high-intensity (4 x 10(17) and 1.6 x 10(18) W/cm(2)) and 1 microm wavelength laser pulses were crossed in a plasma of density 4 x 10(19) cm(3). Energy was observed to be transferred from the higher-power to the lower-power pulse, increasing the amplitude of the plasma wave propagating in the direction of the latter. This results in increased electron self-trapping and plasma-wave acceleration gradient, which led to an increased number of hot electrons (by 300%) and hot-electron temperature (by 70%) and a decreased electron-beam divergence angle (by 45%), as compared with single-pulse illumination. Simulations reveal that increased stochastic heating of electrons may have also contributed to the electron-beam enhancement.

  19. Electrothermal efficiency, temperature and thermal conductivity of plasma jet in a DC plasma spray torch

    Indian Academy of Sciences (India)

    G Shanmugavelayutham; V Selvarajan

    2003-12-01

    A study was made to evaluate the electrothermal efficiency of a DC arc plasma torch and temperature and thermal conductivity of plasma jet in the torch. The torch was operated at power levels from 4 to 20 kW in non-transferred arc mode. The effect of nitrogen in combination with argon as plasma gas on the above properties was investigated. Calculations were made from experimental data. The electrothermal efficiency increased significantly with increase in nitrogen content. The plasma jet temperature and thermal conductivity exhibited a decrease with increase in nitrogen content. The experiment was done at different total gas flow rates. The results are explained on the basis of dissociation energy of nitrogen molecules and plasma jet energy loss to the cathode, anode and the walls of the torch.

  20. Insulin decreases plasma cholesteryl ester transfer but not cholesterol esterification in healthy subjects as well as in normotriglyceridaemic patients with type 2 diabetes

    NARCIS (Netherlands)

    R.P.F. Dullaart (Robin); S.C. Riemens; L. Scheek (Leo); A. van Tol (Arie)

    1999-01-01

    textabstractBackground. Plasma cholesterol esterification (EST) and subsequent cholesteryl ester transfer (CET) from high-density lipoproteins (HDLs) towards apolipoprotein (apo) B-containing lipoproteins are key steps in HDL metabolism. Materials and methods. The effects of exogenous