WorldWideScience

Sample records for plasma processing discharges

  1. Plasma Discharge Process in a Pulsed Diaphragm Discharge System

    Science.gov (United States)

    Duan, Jianjin; Hu, Jue; Zhang, Chao; Wen, Yuanbin; Meng, Yuedong; Zhang, Chengxu

    2014-12-01

    As one of the most important steps in wastewater treatment, limited study on plasma discharge process is a key challenge in the development of plasma applications. In this study, we focus on the plasma discharge process of a pulsed diaphragm discharge system. According to the analysis, the pulsed diaphragm discharge proceeds in seven stages: (1) Joule heating and heat exchange stage; (2) nucleated site formation; (3) plasma generation (initiation of the breakdown stage); (4) avalanche growth and plasma expansion; (5) plasma contraction; (6) termination of the plasma discharge; and (7) heat exchange stage. From this analysis, a critical voltage criterion for breakdown is obtained. We anticipate this finding will provide guidance for a better application of plasma discharges, especially diaphragm plasma discharges.

  2. Review of relaxation oscillations in plasma processing discharges

    Institute of Scientific and Technical Information of China (English)

    Zhou Zhu-Wen; M.A.Lieberman; Sungjin Kim

    2007-01-01

    Relaxation oscillations due to plasma instabilities at frequencies ranging from a few Hz to tens of kHz have been observed in various types of plasma processing discharges.Relaxation oscillations have been observed in electropositive capacitive discharges between a powered anode and a metallic chamber whose periphery iS grounded through a slot with dielectric spacers.The oscillations of time-varying optical emission from the main discharge chamber show,for example,a high-frequency (~40 kHz) relaxation oscillation at 13.33Pa,with an absorbed power being nearly the peripheral breakdown power,and a low-frequency (~3 Hz) oscillation,with an even higher absorbed power.The high-frequency oscillation is found to ignite plasma in the slot,but usually not in the peripheral chamber.The kilohertz oscillations are modelled using an electromagnetic model of the slot impedance,coupled to a circuit analysis of the system including the matching network.The model results are in general agreement with the experimental observations,and indicate a variety of behaviours dependent on the matching conditions.In low-pressure inductive discharges,oscillations appear in the transition between low-density capacitively driven and high-density inductively driven discharges when attaching gases such as SF6 and Ar/SF6 mixtures are used.Oscillations of charged particles,plasma potential,and light,at frequencies ranging from a few Hz to tens of kHz,are seen for gas pressures between 0.133 Pa and 13.33 Pa and discharge powers in a range of 75-1200 W.The region of instability increases as the plasma becomes more electronegative,and the frequency of plasma oscillation increases as the power,pressure,and gas flow rate increase.A volume-averaged (global) model of the kilohertz instability has been developed;the results obtained from the model agree well with the experimental observations.

  3. The Main Plasma Chemical Process of Nitric Oxide Production by Arc Discharge%The Main Plasma Chemical Process of Nitric Oxide Production by Arc Discharge

    Institute of Scientific and Technical Information of China (English)

    杨旗; 胡辉; 陈卫鹏; 许杰; 张锦丽; 吴双

    2011-01-01

    By adopting the optical multi-channel analyzer combined with fourier transform infrared (FTIR) spectrometer, the dominant free radicals and products generated by arc discharge were measured and studied, and the main plasma chemical reaction process in the nitric oxide production by arc discharge was identified. Plasma chemical kinetic curves of O, O2, N2, N and NO were simulated by using CHEMKIN and MATLAB. The results show that the main plasma chemical reaction process of nitric oxide production by arc discharge is a replacement reaction between O and N2, where NO can be generated instantaneously when discharging reaches stable.

  4. Time dependent atomic processes in discharge produced low Z plasma

    Science.gov (United States)

    Yuyama, M.; Sasaki, T.; Horioka, K.; Kawamura, T.

    2008-05-01

    The z-pinch simulation have been performed with magneto-hydro dynamics and atomic population kinetics codes. A factor associated with transient atomic processes was proposed. The atomic transient degrees of dopant lithium in hydrogen plasma were calculated with initial plasma densities of 1.0 × 1016 ~ 5.0 × 1017cm-3. The higher initial plasma density is, the lower is the transient degree generally. It is also found that the transient properties of the atomic processes are sensitive to ionization energy and electron temperature.

  5. Theory of gas discharge plasma

    CERN Document Server

    Smirnov, Boris M

    2015-01-01

    This book presents the theory of gas discharge plasmas in a didactical way. It explains the processes in gas discharge plasmas. A gas discharge plasma is an ionized gas which is supported by an external electric field. Therefore its parameters are determined by processes in it. The properties of a gas discharge plasma depend on its gas component, types of external fields, their geometry and regimes of gas discharge. Fundamentals of a gas discharge plasma include elementary, radiative and transport processes which are included in its kinetics influence. They are represented in this book together with the analysis of simple gas discharges. These general principles are applied to stationary gas discharge plasmas of helium and argon. The analysis of such plasmas under certain conditions is theoretically determined by numerical plasma parameters for given regimes and conditions.

  6. Analysis of Physics Processes in the AC Plasma Torch Discharge under High Pressure

    Science.gov (United States)

    Safronov, A. A.; Vasilieva, O. B.; Dudnik, J. D.; E Kuznetsov, V.; Kuchina, J. A.; Shiryaev, V. N.; Pavlov, A. V.

    2017-04-01

    The paper is devoted to investigation of electrophysical processes in the electric discharge generated by a three-phase AC plasma torch when using a high pressure inert working gas. AC plasma torch design with end electrodes intended for work on inert gases at pressures up to 81 bar is studied. Current-voltage characteristics for different gas flow rates and pressures are presented. Physical processes characteristics of the arising voltage ripples which depend on various working parameters of the plasma torch have been investigated. Arc burning processes in the electric discharge chamber of the three-phase AC plasma torch at various working parameters were photographed.

  7. Discharge processes and an electrical model of atmospheric pressure plasma jets in argon

    Science.gov (United States)

    Fang, Zhi; Shao, Tao; Yang, Jing; Zhang, Cheng

    2016-01-01

    In this paper, an atmospheric pressure plasma discharge in argon was generated using a needle-to-ring electrode configuration driven by a sinusoidal excitation voltage. The electric discharge processes and discharge characteristics were investigated by inspecting the voltage-current waveforms, Lissajous curves and lighting emission images. The change in discharge mode with applied voltage amplitude was studied and characterised, and three modes of corona discharge, dielectric barrier discharge (DBD) and jet discharge were identified, which appeared in turn with increasing applied voltage and can be distinguished clearly from the measured voltage-current waveforms, light-emission images and the changing gradient of discharge power with applied voltage. Based on the experimental results and discharge mechanism analysis, an equivalent electrical model and the corresponding equivalent circuit for characterising the whole discharge processes accurately was proposed, and the three discharge stages were characterised separately. A voltage-controlled current source (VCCS) associated with a resistance and a capacitance were used to represent the DBD stage, and the plasma plume and corona discharge were modelled by a variable capacitor in series with a variable resistor. Other factors that can influence the discharge, such as lead and stray capacitance values of the circuit, were also considered in the proposed model. Contribution to the Topical Issue "Recent Breakthroughs in Microplasma Science and Technology", edited by Kurt Becker, Jose Lopez, David Staack, Klaus-Dieter Weltmann and Wei Dong Zhu.

  8. Simulation of polyatomic discharges for thin film deposition processes in low-pressure plasma reactors

    Science.gov (United States)

    Bera, Kallol

    conditions of experimental reactors. The discharge models were used to investigate the effects of operating and design parameters of the reactors on plasma process characteristics to obtain better process characteristics on the wafer. These parameters can be used to design new reactors for the deposition/etching process. The models can be modified for different feed gases for other applications like plasma etching or sputtering.

  9. Transferred plasma jet from a dielectric barrier discharge for processing of poly(dimethylsiloxane) surfaces

    CERN Document Server

    Nascimento, Fellype do; Canesqui, Mara A; Moshkalev, Stanislav

    2016-01-01

    In this work we studied processing of poly(dimethylsiloxane) (PDMS) surfaces using dielectric barrier discharge (DBD) plasma in two different assemblies, one using the primary plasma jet obtained from a conventional DBD and the other using a DBD plasma jet transfer. The evolution of water contact angle (WCA) in function of plasma processing time and in function of aging time as well as the changes in the surface roughness of PDMS samples for both plasma treatments have been studied. We also compared vibrational and rotational temperatures for both plasmas and for the first time the vibrational temperature (T_vib) for the transferred plasma jet has been shown to be higher as compared with the primary jet. The increment in the T_vib value seems to be the main reason for the improvements in adhesion properties and surface wettability for the transferred plasma jet. Possible explanations for the increase in the vibrational temperature are presented.

  10. Plasma processes in water under effect of short duration pulse discharges

    Science.gov (United States)

    Gurbanov, Elchin

    2013-09-01

    It is very important to get a clear water without any impurities and bacteria by methods, that don't change the physical and chemical indicators of water now. In this article the plasma processes during the water treatment by strong electric fields and short duration pulse discharges are considered. The crown discharge around an electrode with a small radius of curvature consists of plasma leader channels with a high conductivity, where the thermo ionization processes and UV-radiation are taken place. Simultaneously the partial discharges around potential electrode lead to formation of atomic oxygen and ozone. The spark discharge arises, when plasma leader channels cross the all interelectrode gap, where the temperature and pressure are strongly grown. As a result the shock waves and dispersing liquid streams in all discharge gap are formed. The plasma channels extend, pressure inside it becomes less than hydrostatic one and the collapse and UV-radiation processes are started. The considered physical processes can be successfully used as a basis for development of pilot-industrial installations for conditioning of drinking water and to disinfecting of sewage.

  11. Quantitative Analysis on Carbon Migration in Double-Glow Discharge Plasma Surface Alloying Process

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhen-xia; WANG Cong-zeng; ZHANG Wen-quan; SU Xue-kuan

    2004-01-01

    Carbon migration is of great significance in double-glow discharge plasma surface alloying process, but literature of quantitative analysis about carbon migration is relatively scarce. In this paper differential equations of the carbon and metal concentration distribution were established. By means of differential equations carbon migration was described and a numerical solution was acquired. The computational results fit the experiment results quite well.

  12. Process of commutation of a vacuum electric-discharge gap by laser plasma

    Energy Technology Data Exchange (ETDEWEB)

    Davydov, S. G., E-mail: asvi@mail.ru; Dolgov, A. N.; Kozlovskaya, T. I.; Revazov, V. O.; Seleznev, V. P.; Yakubov, R. Kh. [Dukhov All-Russian Research Institute of Automatics (Russian Federation)

    2016-01-15

    The temporal parameters of a process of vacuum gap commutation under exposure to a nanosecond pulse of laser radiation incident on the cathode has been studied depending on the radiation energy. Based on the experiment data, it is suggested that a glow discharge is initially ignited in electrode erosion products under exposure to the laser pulse, which due to development of the ionization-overheating instability undergoes the contraction of current channel and transits to an arc discharge. With the radiation energy exceeding a threshold value, the radiation (incident on the cathode) accelerates directly the instability development and the glow discharge transition to the arc discharge due to the radiation absorption in the discharge plasma.

  13. Modeling electronegative plasma discharge

    Energy Technology Data Exchange (ETDEWEB)

    Lichtenberg, A.J.; Lieberman, M.A. [Univ. of California, Berkley, CA (United States)

    1995-12-31

    Macroscopic analytic models for a three-component electronegative gas discharge are developed. Assuming the negative ions to be in Boltzmann equilibrium, a positive ion ambipolar diffusion equation is derived. The discharge consists of an electronegative core and electropositive edges. The electron density in the core is nearly uniform, allowing a parabolic approximation to the plasma profile to be employed. The resulting equilibrium equations are solved analytically and matched to a constant mobility transport model of an electropositive edge plasma. The solutions are compared to a simulation of a parallel-plane r.f. driven oxygen plasma for p = 50 mTorr and n{sub eo}= 2.4 x 10{sup 15} m{sup -3}. The ratio {alpha}{sub o} of central negative ion density to electron density, and the electron temperature T{sub e}, found in the simulation, are in reasonable agreement with the values calculated from the model. The model is extended to: (1) low pressures, where a variable mobility model is used in the electropositive edge region; and (2) high {alpha}{sub o} in which the edge region disappears. The inclusion of a second positive ion species, which can be very important in describing electronegative discharges used for materials processing, is a possible extension of the model.

  14. Inactivation of Bacteria in Oil Field Injected Water by a Pulsed Plasma Discharge Process

    Science.gov (United States)

    Xin, Qing; Li, Zhongjian; Lei, Lecheng; Yang, Bin

    2016-09-01

    Pulsed plasma discharge was employed to inactivate bacteria in the injection water for an oil field. The effects of water conductivity and initial concentration of bacteria on elimination efficiency were investigated in the batch and continuous flow modes. It was demonstrated that Fe2+ contained in injection water could enhance the elimination efficiency greatly. The addition of reducing agent glutathione (GSH) indicated that active radicals generated by pulsed plasma discharges played an important role in the inactivation of bacteria. Moreover, it was found that the microbial inactivation process for both batch and continuous flow mode well fitted the model based on the Weibull's survival function. supported by Zhejiang Province Welfare Technology Applied Research Project of China (No. 2014C31137), National Natural Science Foundation of China (Nos. 21436007 and U1462201), and the Fundamental Research Funds for the Central Universities of China (No. 2015QNA4032)

  15. The evidence of cathodic micro-discharges during plasma electrolytic oxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Nominé, A., E-mail: alexandre.nomine@univ-lorraine.fr [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine, Parc de Saurupt, 54011 Nancy (France); National Institute of Science and Technology “MISiS,” 4, Leninskij Prospekt, Moscow 119049 (Russian Federation); Martin, J.; Noël, C.; Henrion, G.; Belmonte, T. [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine, Parc de Saurupt, 54011 Nancy (France); Bardin, I. V.; Kovalev, V. L.; Rakoch, A. G. [National Institute of Science and Technology “MISiS,” 4, Leninskij Prospekt, Moscow 119049 (Russian Federation)

    2014-02-24

    Plasma electrolytic oxidation (PEO) processing of EV31 magnesium alloy has been carried out in fluoride containing electrolyte under bipolar pulse current regime. Unusual PEO cathodic micro-discharges have been observed and investigated. It is shown that the cathodic micro-discharges exhibit a collective intermittent behavior, which is discussed in terms of charge accumulations at the layer/electrolyte and layer/metal interfaces. Optical emission spectroscopy is used to determine the electron density (typ. 10{sup 15} cm{sup −3}) and the electron temperature (typ. 7500 K) while the role of F{sup −} anions on the appearance of cathodic micro-discharges is pointed out.

  16. Plasma diagnostics discharge parameters and chemistry

    CERN Document Server

    Auciello, Orlando

    1989-01-01

    Plasma Diagnostics, Volume 1: Discharge Parameters and Chemistry covers seven chapters on the important diagnostic techniques for plasmas and details their use in particular applications. The book discusses optical diagnostic techniques for low pressure plasmas and plasma processing; plasma diagnostics for electrical discharge light sources; as well as Langmuir probes. The text also describes the mass spectroscopy of plasmas, microwave diagnostics, paramagnetic resonance diagnostics, and diagnostics in thermal plasma processing. Electrical engineers, nuclear engineers, microwave engineers, che

  17. NITROGEN POTENTIAL DURING ION NITRIDING PROCESS IN GLOW-DISCHARGE PLASMA

    Directory of Open Access Journals (Sweden)

    A. A. Kozlov

    2015-01-01

    Full Text Available The paper considers problems on regulation of phase composition of a nitrided layer during gas and ion nitriding process in a glow-discharge. It has been established that  available models for control of nitrided layer structure with the help of nitriding index (nitrogen potential can not be applied for nitriding process in the glow-discharge. Principal difference of the ion nitriding from the gas one is in the fact that chemically active nitrogen is formed in the discharge zone (cathode layer and its mass-transfer is carried out in the form of an active particle flow (ions, atoms, molecules which directed to the metal surface.Interrelation of chemical discharge activity with such characteristics of nitriding steel as nitrogen solubility in  α-solid solution and  coefficient diffusion during ion nitriding in low-discharge plasma. It has been shown that regulation of the nitride layer structure during ion nitriding is reached due to changes in nitrogen flow density in plasma. While supporting the flow at the level of nitrogen solubility in  one phase or another (α, γ′  it is possible to obtain the nitrided layer consisting only of α-solid solution or γ′-nitride layer and diffusion sub-layer. Moreover a specific range of nitrogen flow density values exists for every steel grade where it is possible to ensure a limiting nitrogen concentration in α-solid solution and the γ′-layer characterized by low diffusion  mobility is not formed on the surface.

  18. Electrosurgical Plasma Discharges

    Science.gov (United States)

    Stalder, K. R.; Woloszko, J.

    2002-10-01

    Electrosurgical instruments employing plasmas to volumetrically ablate tissue are now enjoying widespread use in medical applications. We have studied several commercially available instruments in which luminous plasma discharges are formed near electrodes immersed in saline solutions when sufficiently large amplitude bipolar voltage waveforms are applied. Different aqueous salt solutions have been investigated, including isotonic NaCl solution as well as solutions of KCl, and BaCl_2. With strong driving voltage applied, a vapor layer is formed as well as visible and UV optical emissions. Spectroscopic measurements reveal the predominant emissions are from the low ionization potential salt species, but significant emissions from electron impact dissociated water fragments such as OH and H-atoms also are observed. The emissions also coincide with negative bias on the active electrode. These optical emissions are consistent with an electron density of about 10^12cm-3 and an electron temperature of about 4 eV. Experimental results and model calculations of the vapor layer formation process and plasma formation in the high-field region will be discussed.

  19. Synthesis and characteristics of Ag/Pt bimetallic nanocomposites by arc-discharge solution plasma processing.

    Science.gov (United States)

    Pootawang, Panuphong; Saito, Nagahiro; Takai, Osamu; Lee, Sang-Yul

    2012-10-05

    Arc discharge in solution, generated by applying a high voltage of unipolar pulsed dc to electrodes of Ag and Pt, was used as a method to form Ag/Pt bimetallic nanocomposites via electrode erosion by the effects of the electric arc at the cathode (Ag rod) and the sputtering at the anode (Pt rod). Ag/Pt bimetallic nanocomposites were formed as colloidal particles dispersed in solution via the reduction of hydrogen radicals generated during discharge without the addition of chemical precursor or reducing agent. At a discharge time of 30 s, the fine bimetallic nanoparticles with a mean particle size of approximately 5 nm were observed by transmission electron microscopy (TEM). With increasing discharge time, the bimetallic nanoparticle size tended to increase by forming an agglomeration. The presence of the relatively small amount of Pt dispersed in the Ag matrix could be observed by the analytical mapping mode of energy-dispersive x-ray spectroscopy and high-resolution TEM. This demonstrated that the synthesized particle was in the form of a nanocomposite. No contamination of other chemical substances was detected by x-ray photoelectron spectroscopy. Hence, solution plasma could be a clean and simple process to effectively synthesize Ag/Pt bimetallic nanocomposites and it is expected to be widely applicable in the preparation of several types of nanoparticle.

  20. Plasma polymers deposited in atmospheric pressure dielectric barrier discharges: Influence of process parameters on film properties

    Energy Technology Data Exchange (ETDEWEB)

    Fricke, Katja, E-mail: k.fricke@inp-greifswald.de [Leibniz Institute for Plasma Science and Technology e.V. (INP Greifswald), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Girard-Lauriault, Pierre-Luc [Plasma Processing Laboratory, Department of Chemical Engineering, McGill University, 3610 rue University, Montreal, QC H3A 0C5 (Canada); Weltmann, Klaus-Dieter [Leibniz Institute for Plasma Science and Technology e.V. (INP Greifswald), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Wertheimer, Michael R. [Department of Engineering Physics, École Polytechnique de Montréal, Box 6079, Station Centre-Ville, Montreal, QC H3C 3A7 (Canada)

    2016-03-31

    We present results on the deposition of plasma polymer (PP) films in a dielectric barrier discharge system fed with mixtures of argon or nitrogen carrier gas plus different hydrocarbon precursors, where the latter possess different carbon-to-hydrogen ratios: CH{sub 4} < C{sub 2}H{sub 6} < C{sub 2}H{sub 4} = C{sub 3}H{sub 6} < C{sub 2}H{sub 2}. The influence of precursor gas mixture and flow rate, excitation frequency, and absorbed power on PP film compositions and properties has been investigated. The discharge was characterized by electrical measurements, while the chemical compositions and structures of coatings were analysed by X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, total combustion, and elastic recoil detection analyses, the latter two for determining carbon-to-hydrogen ratios. Scanning electron microscopy was used to study the coatings' morphology, and profilometry for evaluating deposition rates. - Highlights: • Atmospheric pressure DBD is used to deposit organic hydrocarbon films. • High deposition rates can be achieved by varying the power and/or gas mixture ratio. • Process parameters affect the films' surface chemical composition and morphology. • Deposited films are not soluble in aqueous environment. • No delamination of coatings produced from argon plasma.

  1. Separation Process of Polydisperse Particles in the Plasma of Radio-frequency Discharge

    Directory of Open Access Journals (Sweden)

    D.G. Batryshev

    2014-07-01

    Full Text Available Method of separation of polydisperse particles in the plasma of radio-frequency (RF discharge is considered. Investigation of plasma equipotential field gave conditions for separation. The purpose of this work was an obtaining of monodisperse particles in the plasma of RF discharge. Samples of monodisperse microparticles of silica and alumina were obtained. The size and chemical composition of samples were studied on a scanning electron microscope Quanta 3D 200i (SEM, USA FEI company. Average size of separated silica nanoparticles is 600 nm, silica and alumina microparticles is 5 mkm.

  2. Plasma Characteristics of Electrosurgical Discharges*

    Science.gov (United States)

    Stalder, Kenneth R.

    2003-10-01

    Surgical devices utilizing electrical discharges of ever increasing sophistication have been used for decades for numerous procedures. Cushing and Bovie in 1928, for example, developed high-frequency spark generators to cauterize blood vessels and remove unwanted tissue by a thermal ablation processes. Modern Bovies (named after their inventor) use a high-frequency discharge from an electrode to nearby tissue to thermally ablate tissue. Spectroscopic analysis shows that these discharges are hot and are well represented by a thermal equilibrium model, and temperatures near 2000 K are easily achieved. New electrosurgical devices utilizing repetitive electrical discharges in a conducting saline environment have recently been developed. Electron emission from an active electrode during certain portions of the voltage waveform causes the formation of a vapor layer surrounding the electrode and the subsequent ionization and dissociation of species in this region. Electron temperatures of approximately 4 eV are achieved during the plasma phase. Water molecules are dissociated into reactive fragments, and the salt species are also excited and ionized in this nonequilibrium plasma. It is thought that the reactive species interact with nearby tissue, causing localized tissue removal (ablation) which surgeons can exploit during surgical procedures. Flowing saline surrounding the plasma region cools untargeted tissue and removes the reaction products. This presentation will focus on experimental results of the plasma conditions and discuss our current efforts to understand the complex reactions of the various plasma species with tissue structures such as collagen. A short clip showing tissue removal will also be shown.

  3. Characterization of Ni ferrites powders prepared by plasma arc discharge process

    Science.gov (United States)

    Safari, A.; Gheisari, Kh.; Farbod, M.

    2017-01-01

    The aim of this work was to synthesize a single-phase spinel structure from a mixture of zinc, iron and nickel powders by plasma arc discharge method. A mixture of zinc, iron and nickel powders with the appropriate molar ratio was prepared and formed into a cylindrical shape. The synthesis process was performed in air, oxygen and argon atmospheres with the applied arc current of 400 A and pressure of 1 atm. After establishing an arc between the electrodes, the produced powders were collected and their structure and magnetic properties were examined by XRD and VSM, respectively. ZnO as an impurity was appeared in the as-produced powders owing to the high reactivity of zinc atoms, preventing the formation of Ni-Zn ferrite. A pure spinel structure with the highest saturation magnetization (43.8 emu/g) was observed as zinc powders removed completely from the initial mixture. Morphological evaluations using field emission scanning electron microscopy showed that the mean size of fabricated nanoparticles was in the range 100-200 nm and was dependent on the production conditions.

  4. Absolute Intensities of the Vacuum Ultraviolet Spectra in a Metal-Etch Plasma Processing Discharge

    Energy Technology Data Exchange (ETDEWEB)

    Aragon, B.P.; Blain, M.G.; Hamilton, T.W.; Jarecki, R.L.; Woodworth, J.R.

    1998-12-09

    In this paper we report absolute intensities of vacuum ultraviolet and near ultraviolet emission lines (4.8 eV to 18 eV ) for aluminum etching discharges in an inductively coupled plasma reactor. We report line intensities as a function of wafer type, pressure, gas mixture and rf excitation level. IrI a standard aluminum etching mixture containing C12 and BC13 almost all the light emitted at energies exceeding 8.8 eV was due to neutral atomic chlorine. Optical trapping of the WV radiation in the discharge complicates calculations of VUV fluxes to the wafer. However, we see total photon fluxes to the wailer at energies above 8.8 eV on the order of 4 x 1014 photons/cm2sec with anon- reactive wafer and 0.7 x 10 `4 photons/cm2sec with a reactive wtier. The maj ority of the radiation observed was between 8.9 and 9.3 eV. At these energies, the photons have enough energy to create electron-hole pairs in Si02, but may penetrate up to a micron into the Si02 before being absorbed. Relevance of these measurements to vacuum-W photon-induced darnage of Si02 during etching is discussed.

  5. Plasma Processes : CAMAC based continuous/transient digitizer for long duration discharge

    Indian Academy of Sciences (India)

    Amit Kumar Srivastava; Rachana Rajpal; H D Pujara

    2000-11-01

    With the development of fusion research, in the next generation tokamak like SST1 and ITER the tokamak discharge duration time of the order of 1000 sec is planned. At the same time acquisition of rapid changes of plasma parameters during discharge is required and this demands for higher sampling rate to acquire the data. Hence a large size of RAM (memory) is required to fulfill the above requirements but normally CAMAC based digitizer has limited on-board RAM which can be emptied only after the buffer is completely filled. Therefore, acquisition period is dependent on sampling frequency of the signal as well as on existing size of RAM. This drawback of above is overcome in this design of CAMAC based digitizer where we are using combination of FIFO memory and RAM to get continuous lossless acquisition as well as transient acquisition. This paper includes design of 4-channel CAMAC digitizer with 32 K samples RAM per channel for on-board storage and 8 K samples FIFO per channel for continuous acquisition. The module can be operated in different modes like monitoring, transient acquisition and continuous lossless acquisition with selectable sampling rate

  6. Kinetic analysis of soil contained pyrene oxidation by a pulsed discharge plasma process

    Science.gov (United States)

    Huijuan, Wang; Guangshun, Zhou; He, Guo; Cong, Geng

    2017-01-01

    A pulsed discharge plasma (PDP) reactor with net anode and net cathode was established for investigating the pyrene degradation in soil under different pulse peak voltage, air flow rate, pyrene content in soil, initial pH value and initial water content of the soil. Pyrene oxidation within the 60 min discharge time was fitting according to the pseudo-first order equation and the corresponding reaction kinetics constants (k values) were calculated. The obtained results show that pyrene oxidation under all the different reaction conditions obeyed the pseudo-first order equation well. Higher pulsed peak voltage and appropriate air flow rate were in favor of the increase of reaction rate of pyrene oxidation. A higher k value could be achieved in the lower initial pyrene content (the value was 100 mg kg-1). The k value of pyrene oxidation in the case of pH = 4 was 11.2 times higher than the value obtained under the condition of pH = 9, while the initial water content of the soil also has a large effect on the oxidation rate of pyrene due to the effect of PDP. Supported by National Natural Science Foundation of China (No. 21207052).

  7. Helicon plasma thruster discharge model

    Energy Technology Data Exchange (ETDEWEB)

    Lafleur, T., E-mail: trevor.lafleur@lpp.polytechnique.fr [Laboratoire de Physique des Plasmas, CNRS, Sorbonne Universités, UPMC Univ Paris 06, Univ Paris-Sud, Ecole Polytechnique, 91128 Palaiseau, France and ONERA - The French Aerospace Lab, 91120 Palaiseau (France)

    2014-04-15

    By considering particle, momentum, and energy balance equations, we develop a semi-empirical quasi one-dimensional analytical discharge model of radio-frequency and helicon plasma thrusters. The model, which includes both the upstream plasma source region as well as the downstream diverging magnetic nozzle region, is compared with experimental measurements and confirms current performance levels. Analysis of the discharge model identifies plasma power losses on the radial and back wall of the thruster as the major performance reduction factors. These losses serve as sinks for the input power which do not contribute to the thrust, and which reduce the maximum plasma density and hence propellant utilization. With significant radial plasma losses eliminated, the discharge model (with argon) predicts specific impulses in excess of 3000 s, propellant utilizations above 90%, and thruster efficiencies of about 30%.

  8. Analysis of radiofrequency discharges in plasma

    Science.gov (United States)

    Kumar, Devendra; McGlynn, Sean P.

    1992-01-01

    Separation of laser optogalvanic signals in plasma into two components: (1) an ionization rate change component, and (2) a photoacoustic mediated component. This separation of components may be performed even when the two components overlap in time, by measuring time-resolved laser optogalvanic signals in an rf discharge plasma as the rf frequency is varied near the electrical resonance peak of the plasma and associated driving/detecting circuits. A novel spectrometer may be constructed to make these measurements. Such a spectrometer would be useful in better understanding and controlling such processes as plasma etching and plasma deposition.

  9. Treatment of gaseous effluents by using surface discharge plasma in continuous reactors: Process modelling and simulation

    OpenAIRE

    Assadi, Aymen,; Bouzaza, Abdelkrim; Wolbert, Dominique

    2015-01-01

    International audience; In the present work, the oxidation of isovaleraldehyde, a typical pollutant of indoor air, is investigated by using two different plasma DBD reactors: cylindrical and planar reactor. The study of the influence of the specific energy shows that its increment is accompanied by an increase of the removal efficiency. In fact, when specific energy extends three times, the removal efficiency is increased from 5 to 40%. Moreover an increase of the specific energy induces a hi...

  10. Treatment of gaseous effluents by using surface discharge plasma in continuous reactors: Process modelling and simulation

    OpenAIRE

    Assadi, Aymen; Bouzaza, Abdelkrim; Wolbert, Dominique

    2015-01-01

    International audience; In the present work, the oxidation of isovaleraldehyde, a typical pollutant of indoor air, is investigated by using two different plasma DBD reactors: cylindrical and planar reactor. The study of the influence of the specific energy shows that its increment is accompanied by an increase of the removal efficiency. In fact, when specific energy extends three times, the removal efficiency is increased from 5 to 40%. Moreover an increase of the specific energy induces a hi...

  11. Fluorine and boron co-doped diamond-like carbon films deposited by pulsed glow discharge plasma immersion ion processing

    CERN Document Server

    He, X M; Peters, A M; Taylor, B; Nastasi, M

    2002-01-01

    Fluorine (F) and boron (B) co-doped diamond-like carbon (FB-DLC) films were prepared on different substrates by the plasma immersion ion processing (PIIP) technique. A pulse glow discharge plasma was used for the PIIP deposition and was produced at a pressure of 1.33 Pa from acetylene (C sub 2 H sub 2), diborane (B sub 2 H sub 6), and hexafluoroethane (C sub 2 F sub 6) gas. Films of FB-DLC were deposited with different chemical compositions by varying the flow ratios of the C sub 2 H sub 2 , B sub 2 H sub 6 , and C sub 2 F sub 6 source gases. The incorporation of B sub 2 H sub 6 and C sub 2 F sub 6 into PIIP deposited DLC resulted in the formation of F-C and B-C hybridized bonding structures. The levels of the F and B concentrations effected the chemical bonding and the physical properties as was evident from the changes observed in density, hardness, stress, friction coefficient, and contact angle of water on films. Compared to B-doped or F-doped DLC films, the F and B co-doping of DLC during PIIP deposition...

  12. Efficient new process for the desulfurization of mixtures of air and hydrogen sulfide via a dielectric barrier discharge plasma

    Directory of Open Access Journals (Sweden)

    S. Dahle

    2015-10-01

    Full Text Available The efficient removal of hydrogen sulfide, H2S, from streams of H2S in air via a dielectric barrier discharge (DBD plasma has been investigated using a quadrupole mass spectrometer. A suitable plasma device with a reservoir for storing sorbent powder of various kinds within the plasma region was constructed. Plasma treatments of gas streams with high concentrations of hydrogen sulfide in air yielded a removal of more than 98% of the initial hydrogen sulfide and a deposition of sulfur at the surface of the dielectric, while small amounts of sulfur dioxide were generated. The presence of calcium carbonate within the plasma region of the DBD device resulted in the removal of over 99% of the initial hydrogen sulfide content and the removal of 98% of the initial sulfur dioxide impurities from the gas mixture.

  13. Electrochemical Discharge Machining Process

    Directory of Open Access Journals (Sweden)

    Anjali V. Kulkarni

    2007-09-01

    Full Text Available Electrochemical discharge machining process is evolving as a promising micromachiningprocess. The experimental investigations in the present work substantiate this trend. In the presentwork, in situ, synchronised, transient temperature and current measurements have been carriedout. The need for the transient measurements arose due to the time-varying nature of the dischargeformation and time varying circuit current. Synchronised and transient measurements revealedthe discrete nature of the process. It also helped in formulating the basic mechanism for thedischarge formation and the material removal in the process. Temperature profile on workpieceand in electrochemical discharge machining cell is experimentally measured using pyrometer,and two varieties of K-type thermocouples. Surface topography of the discharge-affected zoneson the workpiece has been carried out using scanning electron microscope. Measurements andsurface topographical studies reveal the potential use of this process for machining in micronregime. With careful experimental set-up design, suitable supply voltage and its polarity, theprocess can be applied for both micromachining and micro-deposition. It can be extended formachining and or deposition of wide range of materials.

  14. Plasma spark discharge reactor and durable electrode

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Young I.; Cho, Daniel J.; Fridman, Alexander; Kim, Hyoungsup

    2017-01-10

    A plasma spark discharge reactor for treating water. The plasma spark discharge reactor comprises a HV electrode with a head and ground electrode that surrounds at least a portion of the HV electrode. A passage for gas may pass through the reactor to a location proximate to the head to provide controlled formation of gas bubbles in order to facilitate the plasma spark discharge in a liquid environment.

  15. Generation of Volatile Cadmium and Zinc Species Based on Solution Anode Glow Discharge Induced Plasma Electrochemical Processes.

    Science.gov (United States)

    Liu, Xing; Liu, Zhifu; Zhu, Zhenli; He, Dong; Yao, Siqi; Zheng, Hongtao; Hu, Shenghong

    2017-03-21

    In this study, a novel high efficiency vapor generation strategy was proposed on the basis of solution anode glow discharge for the determination of Cd and Zn by atomic fluorescence spectrometry. In this approach, a glow discharge microplasma was acted as a gaseous cathode to initiate the plasma electrochemical vapor generation of Cd and Zn. Cadmium/zinc ions could be converted into molecular species efficiently at the plasma-liquid interface from a supporting electrolyte (HCl, pH = 3.2). It was found that the overall efficiency of the plasma electrochemical vapor generation (PEVG) system was much higher than the conventional electrochemical hydride generation (EcHG) and HCl-KBH4 system. With no requirement for other reducing reagents, this new approach enabled us to detect Cd and Zn with detection limits as low as 0.003 μg L(-1) for Cd and 0.3 μg L(-1) for Zn. Good repeatability (relative standard deviation (RSD), n = 5) was 2.4% for Cd (0.1 μg L(-1)) and 1.7% for Zn (10 μg L(-1)) standard. The accuracy of the proposed method was successfully validated through analysis of cadmium in reference material of stream sediment (GBW07311), soil (GBW07401), rice (GBW10045), and zinc in a simulated water sample (GSB 07-1184-2000). Replacing a metal electrode with a plasma offers the advantage of eliminating potential interactions between the species in liquid and the electrode, which solves the issues associated with electrode encountered in conventional EcHG. The ability to initiate electrochemical vapor generation reactions at the plasma-liquid interface opens a new approach for chemical vapor generation based on interactions between plasma gas-phase electrons and solutions.

  16. Combustion Enhancement with a Silent Discharge Plasma

    Science.gov (United States)

    Rosocha, Louis

    2003-10-01

    It is well known that the application of an external electric field to a flame can affect its propagation speed, stability, and combustion chemistry (Lawton & Weinberg 1969). External electrodes, arc discharges, and plasma jets have been employed to allow combustible gas mixtures to operate outside their flammability limits by gas heating, injection of free radicals, and field-promoted flame stabilization (Yagodnikov & Voronetskii 1994). Other investigators have carried out experiments with silent electrical discharges applied to propagating flames (Inomata et al 1983, Kim et al 2003). These have demonstrated that the flame propagation velocity is actually decreased (combustion retarded) when a silent discharge is applied directly to the flame region, but that the flame propagation velocity is increased (combustion promoted) when a silent discharge is applied to the unburned gas mixture upstream of a flame. Two other recent works have considered the possibility of combustion enhancement in aircraft gas turbine engine combustor mixers by using a plasma-generating fuel nozzle, that employs an electric-arc or microwave plasma generator, to produce dissociated fuel or ionized fuel (Johnson et al 2001); and pulsed corona-enhanced detonation of fuel-air mixtures in jet engines (Wang et al 2003). In contrast to these prior works, we have employed a silent discharge plasma (SDP) reactor to break up large fuel molecules into smaller molecules and create free radicals or other active species in a gas stream before the fuel is mixed with an oxidizer and combusted. In experiments reported here, a cylindrical SDP reactor was used to 'activate' propane before mixing it with air and igniting the combustible gas mixture. With the plasma, the physical appearance of the flame changes and substantial changes in mass spectrometer fragmentation peaks are observed (e.g., propane fragments decrease and water and carbon dioxide increase). This indicates that the combustion process is

  17. Plasma discharge self-cleaning filtration system

    Science.gov (United States)

    Cho, Young I.; Fridman, Alexander; Gutsol, Alexander F.; Yang, Yong

    2014-07-22

    The present invention is directed to a novel method for cleaning a filter surface using a plasma discharge self-cleaning filtration system. The method involves utilizing plasma discharges to induce short electric pulses of nanoseconds duration at high voltages. These electrical pulses generate strong Shockwaves that disintegrate and dislodge particulate matter located on the surface of the filter.

  18. Influence of the Discharge Voltage during Pulse-Plasma Process on the Durability of Edges coated with Superhard Coatings

    Institute of Scientific and Technical Information of China (English)

    Maciej Kupczyk

    2004-01-01

    In the paper the experimental results concerning the functional quality of thin, superhard coatings produced on cutting edges is described. Boron nitride coatings were deposited on insert cutting edges made cemented carbides by the pulse-plasma method. The comparative investigations of mentioned coatings have been concerned of tool life of edges during steel machining. In these investigations for the purpose of additional increase of coated edge durability an interfacial layers were applied. Presented investigations particularly pointed out to essential influence of the values of discharge voltage on the coating structure and durability of edges coated with boron nitride.

  19. Influence of the Discharge Voltage during Pulse-Plasma Process on the Durability of Edges coated with Superhard Coatings

    Institute of Scientific and Technical Information of China (English)

    MaciejKupczyk

    2004-01-01

    In the paper the experimental results concerning the functional quality of thin, superhard coatings produced on cutting edges is described. Boron nitride coatings were deposited on insert cutting edges made cemented carbides by the pulse-plasma method. The comparative investigations of mentioned coatings have been concerned of tool life of edges during steel machining. In these investigations for the purpose of additional increase of coated edge durability an interfacial layers were applied. Presented investigations particularly pointed out to essential influence of the values of discharge voltage on the coating structure and durability of edges coated with boron nitfide.

  20. Pulsed discharge plasmas in supercritical carbon dioxide

    OpenAIRE

    Kiyan, Tsuyoshi; Uemura, A.; Tanaka, K.; Zhang, C. H.; Namihira, Takao; Sakugawa, Takashi; Katsuki, Sunao; Akiyama, Hidenori; Roy, B.C.; Sasaki, M.; Goto, M.; キヤン, ツヨシ; ナミヒラ, タカオ; サクガワ, タカシ; カツキ, スナオ

    2005-01-01

    In recent years, several studies about electrical discharge plasma in supercritical carbon dioxide (CO2) have been carried out. One of the unique characteristics of supercritical fluid is a large density fluctuation near the critical point that can result in marked dramatic changes of thermal conductivity. Therefore, the electrical discharge plasma produced in supercritical fluid has unique features and reactions unlike those of normal plasma produced in gas phase. In our experiments, two typ...

  1. Stabilizing effect of plasma discharge on bubbling fluidized granular bed

    Science.gov (United States)

    Hu, Mao-Bin; Dang, Sai-Chao; Ma, Qiang; Xia, Wei-Dong

    2015-07-01

    Fluidized beds have been widely used for processing granular materials. In this paper, we study the effect of plasma on the fluidization behavior of a bubbling fluidized bed with an atmospheric pressure plasma discharger. Experiment results show that the bubbling fluidized bed is stabilized with the discharge of plasma. When the discharge current reaches a minimum stabilization current Cms, air bubbles in the bed will disappear and the surface fluctuation is completely suppressed. A simplified model is proposed to consider the effect of electric Coulomb force generated by the plasma. It is found that the Coulomb force will propel the particles to move towards the void area, so that the bubbling fluidized bed is stabilized with a high enough plasma discharge. Project supported by the National Natural Science Foundation of China (Grant Nos. 11035005 and 11034010).

  2. [Redesigning the hospital discharge process].

    Science.gov (United States)

    Martínez-Ramos, M; Flores-Pardo, E; Uris-Sellés, J

    2016-01-01

    The aim of this article is to show that the redesign and planning process of hospital discharge advances the departure time of the patient from a hospital environment. Quasi-experimental study conducted from January 2011 to April 2013, in a local hospital. The cases analysed were from medical and surgical nursing units. The process was redesigned to coordinate all the professionals involved in the process. The hospital discharge improvement process improvement was carried out by forming a working group, the analysis of retrospective data, identifying areas for improvement, and its redesign. The dependent variable was the time of patient administrative discharge. The sample was classified as pre-intervention, inter-intervention, and post-intervention, depending on the time point of the study. The final sample included 14,788 patients after applying the inclusion and exclusion criteria. The mean discharge release time decreased significantly by 50 min between pre-intervention and post-intervention periods. The release time in patients with planned discharge was one hour and 25 min less than in patients with unplanned discharge. Process redesign is a useful strategy to improve the process of hospital discharge. Besides planning the discharge, it is shown that the patient leaving the hospital before 12 midday is a key factor. Copyright © 2015 SECA. Published by Elsevier Espana. All rights reserved.

  3. Biological and Agricultural Studies on Application of Discharge Plasma and Electromagnetic Fields 2.Sterilization by Electrical Discharges and Plasmas

    Science.gov (United States)

    Watanabe, Takayuki

    The use of electrical discharges and plasmas for sterilization is reviewed. Plasmas generated by a silent discharge, a pulse discharge, and a radio frequency discharge under atmospheric pressure have been used for sterilization. Furthermore, a microwave plasma, a radio frequency plasma, and a low temperature plasma with hydrogen peroxide under low pressure conditions have been also used for sterilization. Sterilization results from injury caused by the discharge current, and from the reaction of species affected by the discharge. A silent discharge with air or oxygen is most effective for the sterilization. Nitrogen discharge also has a significant effect, however, argon discharge does not have a significant effect.

  4. Sheet Plasma Produced by Hollow Cathode Discharge

    Institute of Scientific and Technical Information of China (English)

    张龙; 张厚先; 杨宣宗; 冯春华; 乔宾; 王龙

    2003-01-01

    A sheet plasma is produced by a hollow cathode discharge under an axial magnetic field.The plasma is about 40cm in length,4 cm in width and 1cm in thickness.The electron density is about 108cm-3.The hollow cathode is made to be shallow with a large opening,which is different from the ordinary deep hollow cathode.A Langmuir probe is used to detect the plasma.The electron density and the spatial distribution of the plasma change when voltage,pressure and the magnetic field vary.A peak and a data fluctuation at about 200 G-300 G are observed in the variation of electron density(or thickness of the sheet plasma)with the magnetic field.Our work will be helpful in characterizing the sheet plasma and will make the production of dense sheet plasma more controllable.

  5. Discharge Characteristics of DC Arc Water Plasma for Environmental Applications

    Institute of Scientific and Technical Information of China (English)

    LI Tianming; Sooseok CHOI; Takayuki WATANABE

    2012-01-01

    A water plasma was generated by DC arc discharge with a hafnium embedded rodtype cathode and a nozzle-type anode. The discharge characteristics were examined by changing the operation parameter of the arc current. The dynamic behavior of the arc discharge led to significant fluctuations in the arc voltage and its frequency. Analyses of the high speed image and the arc voltage waveform showed that the arc discharge was in the restrike mode and its frequency varied within several tens of kilohertz according to the operating conditions. The larger thermal plasma volume was generated by the higher flow from the forming steam with a higher restrike frequency in the higher arc current conditions. In addition, the characteristics of the water plasma jet were investigated by means of optical emission spectroscopy to identify the abundant radicals required in an efficient waste treatment process.

  6. Underwater plasma discharge and its water treatment applications

    Science.gov (United States)

    Ma, Sukhwal; Huh, Jin Young; Kim, Kangil; Hong, Yong Cheol; National Fusion Research Institute Team; Chonbuk National University Team; Kwangwoon University Team; NPAC Team

    2016-09-01

    In recent, the quality of water has been exacerbated by the influx of wastewater and water pollutants. There have been frequent occurrences of water blooms due to the eutrophication of river. Therefore, the needs for water treatment are increased through effective and environment-friendly method. In this work, we propose the plasma system to overcome the problems mentioned above using underwater discharge plasma. The underwater discharges are generated by capillary electrode, and have the advantages of low cost, high efficiency and eco-friendly processing. The proposed technologies can be suitable for eliminating cyanobacteria, decreasing the concentration of oil dissolved in water, and purifying wastewater. Cyanobacteria is killed directly by the underwater discharge and water-dissolved oil and heavy-metal wastewater are purified by coagulation effect, which may result from the chemical reactions of underwater plasma. Consequently, these technologies using underwater discharge can be alternative methods to replace the existing technologies.

  7. Analytical calculations of anode plasma position in high-voltage discharge range in case of auxiliary discharge firing

    OpenAIRE

    Melnyk, Igor V.; Tugay, S. B.

    2012-01-01

    We consider the mathematical model of triode high-voltage glow discharge range in case of auxiliary discharge firing. On a basis of analysis of elementary processes of charged particles interaction in a discharge range we obtain analytical relation, which allows to obtain the anode plasma position with regard to the cathode. Obtained results can be used for analysis of analysis of energy balance in a discharge range and self-maintained electron-ion optics of high voltage glow discharge electr...

  8. Discharge-produced plasma extreme ultraviolet (EUV) source and ultra high vacuum chamber for studying EUV-induced processes

    CERN Document Server

    Dolgov, A; Abrikosov, A; Snegirev, E; Krivtsun, V M; Lee, C J; Bijkerk, F

    2014-01-01

    An experimental setup that directly reproduces Extreme UV-lithography relevant conditions for detailed component exposure tests is described. The EUV setup includes a pulsed plasma radiation source, operating at 13.5 nm; a debris mitigation system; collection and filtering optics; and an UHV experimental chamber, equipped with optical and plasma diagnostics. The first results, identifying the physical parameters and evolution of EUV-induced plasmas are presented. Finally, the applicability and accuracy of the in situ diagnostics is briefly discussed.

  9. Recent progress in the application of glow-discharge electrolysis plasma

    National Research Council Canada - National Science Library

    Jie Ren; Mengqi Yao; Wu Yang; Yan Li; Jinzhang Gao

    2014-01-01

    ... produced during the glow-discharge electrolysis (GDE) process. A brief review is already available regarding applications of glow-discharge electrolysis plasma technique in chemistry and environmental science during the past decade...

  10. High-frequency underwater plasma discharge application in antibacterial activity

    Science.gov (United States)

    Ahmed, M. W.; Choi, S.; Lyakhov, K.; Shaislamov, U.; Mongre, R. K.; Jeong, D. K.; Suresh, R.; Lee, H. J.

    2017-03-01

    Plasma discharge is a novel disinfection and effectual inactivation approach to treat microorganisms in aqueous systems. Inactivation of Gram-negative Escherichia coli ( E. coli) by generating high-frequency, high-voltage, oxygen (O2) injected and hydrogen peroxide (H2O2) added discharge in water was achieved. The effect of H2O2 dose and oxygen injection rate on electrical characteristics of discharge and E. coli disinfection has been reported. Microbial log reduction dependent on H2O2 addition with O2 injection was observed. The time variation of the inactivation efficiency quantified by the log reduction of the initial E. coli population on the basis of optical density measurement was reported. The analysis of emission spectrum recorded after discharge occurrence illustrated the formation of oxidant species (OH•, H, and O). Interestingly, the results demonstrated that O2 injected and H2O2 added, underwater plasma discharge had fabulous impact on the E. coli sterilization. The oxygen injection notably reduced the voltage needed for generating breakdown in flowing water and escalated the power of discharge pulses. No impact of hydrogen peroxide addition on breakdown voltage was observed. A significant role of oxidant species in bacterial inactivation also has been identified. Furthermore the E. coli survivability in plasma treated water with oxygen injection and hydrogen peroxide addition drastically reduced to zero. The time course study also showed that the retardant effect on E. coli colony multiplication in plasma treated water was favorable, observed after long time. High-frequency underwater plasma discharge based biological applications is technically relevant and would act as baseline data for the development of novel antibacterial processing strategies.

  11. High-frequency underwater plasma discharge application in antibacterial activity

    Science.gov (United States)

    Ahmed, M. W.; Choi, S.; Lyakhov, K.; Shaislamov, U.; Mongre, R. K.; Jeong, D. K.; Suresh, R.; Lee, H. J.

    2017-03-01

    Plasma discharge is a novel disinfection and effectual inactivation approach to treat microorganisms in aqueous systems. Inactivation of Gram-negative Escherichia coli (E. coli) by generating high-frequency, high-voltage, oxygen (O2) injected and hydrogen peroxide (H2O2) added discharge in water was achieved. The effect of H2O2 dose and oxygen injection rate on electrical characteristics of discharge and E. coli disinfection has been reported. Microbial log reduction dependent on H2O2 addition with O2 injection was observed. The time variation of the inactivation efficiency quantified by the log reduction of the initial E. coli population on the basis of optical density measurement was reported. The analysis of emission spectrum recorded after discharge occurrence illustrated the formation of oxidant species (OH•, H, and O). Interestingly, the results demonstrated that O2 injected and H2O2 added, underwater plasma discharge had fabulous impact on the E. coli sterilization. The oxygen injection notably reduced the voltage needed for generating breakdown in flowing water and escalated the power of discharge pulses. No impact of hydrogen peroxide addition on breakdown voltage was observed. A significant role of oxidant species in bacterial inactivation also has been identified. Furthermore the E. coli survivability in plasma treated water with oxygen injection and hydrogen peroxide addition drastically reduced to zero. The time course study also showed that the retardant effect on E. coli colony multiplication in plasma treated water was favorable, observed after long time. High-frequency underwater plasma discharge based biological applications is technically relevant and would act as baseline data for the development of novel antibacterial processing strategies.

  12. High-frequency underwater plasma discharge application in antibacterial activity

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, M. W.; Choi, S.; Lyakhov, K.; Shaislamov, U. [Jeju National University, Department of Nuclear and Energy Engineering (Korea, Republic of); Mongre, R. K.; Jeong, D. K. [Jeju National University, Faculty of Biotechnology (Korea, Republic of); Suresh, R.; Lee, H. J., E-mail: hjlee@jejunu.ac.kr [Jeju National University, Department of Nuclear and Energy Engineering (Korea, Republic of)

    2017-03-15

    Plasma discharge is a novel disinfection and effectual inactivation approach to treat microorganisms in aqueous systems. Inactivation of Gram-negative Escherichia coli (E. coli) by generating high-frequency, high-voltage, oxygen (O{sub 2}) injected and hydrogen peroxide (H{sub 2}O{sub 2}) added discharge in water was achieved. The effect of H{sub 2}O{sub 2} dose and oxygen injection rate on electrical characteristics of discharge and E. coli disinfection has been reported. Microbial log reduction dependent on H{sub 2}O{sub 2} addition with O{sub 2} injection was observed. The time variation of the inactivation efficiency quantified by the log reduction of the initial E. coli population on the basis of optical density measurement was reported. The analysis of emission spectrum recorded after discharge occurrence illustrated the formation of oxidant species (OH{sup •}, H, and O). Interestingly, the results demonstrated that O{sub 2} injected and H{sub 2}O{sub 2} added, underwater plasma discharge had fabulous impact on the E. coli sterilization. The oxygen injection notably reduced the voltage needed for generating breakdown in flowing water and escalated the power of discharge pulses. No impact of hydrogen peroxide addition on breakdown voltage was observed. A significant role of oxidant species in bacterial inactivation also has been identified. Furthermore the E. coli survivability in plasma treated water with oxygen injection and hydrogen peroxide addition drastically reduced to zero. The time course study also showed that the retardant effect on E. coli colony multiplication in plasma treated water was favorable, observed after long time. High-frequency underwater plasma discharge based biological applications is technically relevant and would act as baseline data for the development of novel antibacterial processing strategies.

  13. Temporal modulation of plasma species in atmospheric dielectric barrier discharges

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Aijun; Wang, Xiaohua, E-mail: xhw@mail.xjtu.edu.cn, E-mail: mzrong@mail.xjtu.edu.cn; Liu, Dingxin; Rong, Mingzhe, E-mail: xhw@mail.xjtu.edu.cn, E-mail: mzrong@mail.xjtu.edu.cn [Centre for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Kong, Michael G. [Centre for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Frank Reidy Research Center for Bioelectrics, Department of Electrical and Computer Engineering, Old Dominion University, Virginia 23508 (United States); Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, Virginia 23529 (United States)

    2014-07-15

    The atmospheric pressure dielectric barrier discharge in helium is a pulsed discharge in nature and the moment of maximum species densities is almost consistent with peak discharge current density. In this paper, a one-dimensional fluid model is used to investigate the temporal structure of plasma species in an atmospheric He-N{sub 2} dielectric barrier discharge (DBD). It is demonstrated that there exist microsecond delays of the moments of the maximum electron and ion densities from the peak of discharge current density. These time delays are caused by a competition between the electron impact and Penning ionizations, modulated by the N{sub 2} level in the plasma-forming gas. Besides, significant electron wall losses lead to the DBD being more positively charged and, with a distinct temporal separation in the peak electron and cation densities, the plasma is characterized with repetitive bursts of net positive charges. The temporal details of ionic and reactive plasma species may provide a new idea for some biological processes.

  14. Elementary processes in gas discharges

    CERN Document Server

    Bronold, Franz X

    2008-01-01

    This chapter presents, from a quantum-mechanical point of view, a tutorial discussion of elementary collision processes in the bulk of a gas discharge. Instead of merely listing kitchen-made cross section formulae and unrelated cross section data, emphasis has been given on an unified description of elementary processes based on general principles of quantum-mechanical multi-channel scattering theory. By necessity, the presentation is rather dense. Technical details left out, as well as cross section data, can be found, respectively, in the quoted original papers and the review articles, monographs, and web-sites mentioned in the introductory remarks to this chapter.

  15. Characterization of a Dielectric Barrier Plasma Gun Discharging at Atmospheric Pressure

    Institute of Scientific and Technical Information of China (English)

    ZHANG Guang-Qiu; GE Yuan-Jing; ZHANG Yue-Fei; CHEN Guang-Liang

    2004-01-01

    @@ We develop a plasma gun based on dielectric barrier discharge and working at atmospheric pressure. A theoretical model to predict the gun discharge voltage is built, which is in agreement with the experimental results. After investigating the characterization of discharging gun and utilizing it for polymerization, we find that the gun can be used as a source to generate a stable uniform plasma for different plasma-processing technologies.

  16. Plasma environment during hot cathode direct current discharge plasma chemical vapor deposition of diamond films

    Institute of Scientific and Technical Information of China (English)

    朱晓东; 詹如娟; 周海洋; 胡敏; 温晓辉; 周贵恩; 李凡庆

    1999-01-01

    The plasma characteristics have been investigated in situ by using optical emission spectroscopy (OES) and the Langmuir probe during hot cathode direct current discharge plasma chemical vapor deposition of diamond films. The changes of atomic H and CH radical in the ground state have been calculated quantitatively according to the results of OES and the Langmuir probe measurement as discharge current density varied. It is shown that atomic H and CH radicals both in the ground state and in the excited state increase with the enhancement of the discharge current density in the plasma. The electron density and CH emission intensity increase linearly with the enhancement of discharge current densities. The generation of different carbon-containing radicals is related to the elevation of electron temperature. Combining the growth process of diamond films and the diagnostic results, it is shown that atomic H in the excited state may improve the diamond growth efficiently, and the increase of electron temperat

  17. Plasma Catalysis of Methane Decomposition in Pulse Microwave Discharge

    Science.gov (United States)

    Potapkin, B.; Rusanov, V.; Jivotov, V.; Babaritski, A.; Potechin, S.; Etievant, C.

    1997-10-01

    Investigation of plasma catalysis effects in various chemical reactions, such as SO2 and hydrocarbons oxidation, ammonia and nitrogen oxides synthesis, has been of interest for many decades. Present work describes the first experimental observation and theoretical analysis of plasma catalysis effects in the case of endothermic methane decomposition into molecular hydrogen and carbon black. Process energy requirements are coverd mainly by low potential gas thermal energy while plasma is used for acceleration of chemical reactions via active species generation. The experiments were done as follows: (i) methane was preheated in a conventional heat exchanger up to about 40-65 ^oC where thermal methane decomposition is limited by process kinetics, (ii) methane was passed through a non-equilibrium pulse microwave discharge (9.04 GHz, pulse duration 1 μs). Experiments have shown a strong catalytic effect of plasma on methane decomposition. The degree of conversion after discharge increased drastically, despite gas cooling, because of heat absorption in the methane decomposition reaction. Theoretical analysis of process kinetics and energy balance gave clear evidence of the catalytic effect of plasma under experimental conditions. The estimated chain length was about 300. The possible mechanism of plasma catalysis, the ion-molecular chain Winchester mechanism, is proposed and described.

  18. Study on electrolytic plasma discharging behavior and its influence on the plasma electrolytic oxidation coatings

    Science.gov (United States)

    Hussein, Riyad Omran

    In this study, aluminum oxide was deposited on a pure aluminum substrate to produce hard ceramic coatings using a Plasma Electrolytic Oxidation (PEO) process. The process utilized DC, unipolar pulsed DC in the frequency range (0.2 KHz -- 20 KHz) and bipolar pulsed DC current modes. The effects of process parameters (i.e., electrolyte concentration, current density and treatment time) on the plasma discharge behavior during the PEO treatment were investigated using optical emission spectroscopy (OES) in the visible and near ultraviolet (NUV) band (285 nm -- 900 nm). The emission spectra were recorded and plasma temperature profile versus processing time was constructed using the line intensity ratios method. Scanning Electron Microscopy (SEM) with energy dispersive x-ray analysis (EDS) was used to study the coating microstructure. It was found that the plasma discharge behavior significantly influenced the microstructure and the morphology of the oxide coatings. The main effect came from the strongest discharges which were initiated at the interface between the substrate and the coating. Through manipulation of process parameters to control or reduce the strongest discharge, the density and quality of the coating layers could be modified. This work demonstrated that by adjusting the ratio of the positive to negative pulse currents as well as their timing in order to eliminate the strongest discharges, the quality of the coatings was considerably improved.

  19. ORAL ISSUE OF THE JOURNAL "USPEKHI FIZICHESKIKH NAUK": Modeling of gas discharge plasma

    Science.gov (United States)

    Smirnov, Boris M.

    2009-06-01

    The condition for the self-maintenance of a gas discharge plasma (GDP) is derived from its ionization balance expressed in the Townsend form and may be used as a definition of a gas discharge plasma in its simplest form. The simple example of a gas discharge plasma in the positive column of a cylindrical discharge tube allows demonstrating a wide variety of possible GDP regimes, revealing a contradiction between simple models used to explain gas discharge regimes and the large number of real processes responsible for the self-maintenance of GDP. The variety of GDP processes also results in a stepwise change of plasma parameters and developing some instabilities as the voltage or discharge current is varied. As a consequence, new forms and new applications of gas discharge arise as technology progresses.

  20. Glow Discharge Plasma Nitriding of AISI 304 Stainless Steel

    Institute of Scientific and Technical Information of China (English)

    A.QAYYUM; M.A.NAVEED; S.ZEB; G.MURTAZA; M.ZAKAULLAH

    2007-01-01

    Glow discharge plasma nitriding of AISI 304 austenitic stainless steel has been carried out for different processing time under optimum discharge conditions established by spectroscopic analysis.The treated samples were analysed by X-ray diffraction(XRD)to explore the changes induced in the crystallographic structure.The XRD pattern confirmed the formation of an expanded austenite phase(γN)owing to incorporation of nitrogen as an interstitial solid solution in the iron lattice.A Vickers microhardness tester was used to evaluate the surface hardness as a function of indentation depth(μm).The results showed clear evidence of surface changes with substantial increase in surface hardness.

  1. Electrical and spectroscopic characterization of a surgical argon plasma discharge

    Science.gov (United States)

    Keller, Sandra; Bibinov, Nikita; Neugebauer, Alexander; Awakowicz, Peter

    2013-01-01

    For electrosurgical procedures, the argon plasma coagulation (APC) discharge is a well-established atmospheric-pressure plasma tool for thermal haemostasis and devitalization of biological tissue. To characterize this plasma source, voltage-current measurements, microphotography, optical emission spectroscopy and numerical simulation are applied. Two discharge modes are established during the operation of the APC plasma source. A short transient spark discharge is ignited within the positive half period of the applied high voltage after a streamer channel connects the APC probe and the counter-electrode. During the second phase, which continues under negative high voltage, a glow discharge is stabilized in the plasma channel.

  2. Scaling and laws of DC discharges as pointers for HiPIMS plasmas

    CERN Document Server

    Maszl, Christian; von Keudell, Achim; Störi, Herbert

    2015-01-01

    Scaling or smiliarity laws of plasmas are of interest if lab size plasma sources are to be scaled for industrial processes. Ideally, the discharge parameters of the scaled plasmas are predictable and the fundamental physical processes are unaltered. Naturally, there are limitations and ranges of validity. Scaling laws for direct current glow discharges are well known. If a well diagnosed discharge is scaled, the field strength in the positive column, the gas amplification and the normal current density can easily be estimated. For non-stationary high power discharges like high power impulse magnetron sputtering (HiPIMS) plasmas, scaling is not as straight forward. Here, one deals with a non-stationary complex system with strong changes in plasma chemistry and symmetry breaks during the pulses. Because of the huge parameter space no good parameters are available to define these kind of discharges unambiguous at the moment. In this contribution we will discuss the scaling laws for DC glow discharges briefly and...

  3. Plasma nitriding process by direct current glow discharge at low temperature increasing the thermal diffusivity of AISI 304 stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Prandel, L. V.; Somer, A.; Assmann, A.; Camelotti, F.; Costa, G.; Bonardi, C.; Jurelo, A. R.; Rodrigues, J. B.; Cruz, G. K. [Universidade Estadual de Ponta Grossa, Grupo de Espectroscopia Optica e Fotoacustica de Materiais, Departamento de Fisica, Av. Carlos Cavalcanti, 4748, CEP 84030-900, Ponta Grossa, PR (Brazil)

    2013-02-14

    This work reports for the first time on the use of the open photoacoustic cell technique operating at very low frequencies and at room temperature to experimentally determine the thermal diffusivity parameter of commercial AISI304 stainless steel and AISI304 stainless steel nitrided samples. Complementary measurements of X-ray diffraction and scanning electron microscopy were also performed. The results show that in standard AISI 304 stainless steel samples the thermal diffusivity is (4.0 {+-} 0.3) Multiplication-Sign 10{sup -6} m{sup 2}/s. After the nitriding process, the thermal diffusivity increases to the value (7.1 {+-} 0.5) Multiplication-Sign 10{sup -6} m{sup 2}/s. The results are being associated to the diffusion process of nitrogen into the surface of the sample. Carrying out subsequent thermal treatment at 500 Degree-Sign C, the thermal diffusivity increases up to (12.0 {+-} 2) Multiplication-Sign 10{sup -6} m{sup 2}/s. Now the observed growing in the thermal diffusivity must be related to the change in the phases contained in the nitrided layer.

  4. Ethanol reforming in non-equilibrium plasma of glow discharge

    CERN Document Server

    Levko, D

    2012-01-01

    The results of a detailed kinetic study of the main plasma chemical processes in non-equilibrium ethanol/argon plasma are presented. It is shown that at the beginning of the discharge the molecular hydrogen is mainly generated in the reaction of ethanol H-abstraction. Later hydrogen is formed from active H, CH2OH and CH3CHOH and formaldehyde. Comparison with experimental data has shown that the used kinetic mechanism predicts well the concentrations of main species at the reactor outlet.

  5. Plasma chemistry in electron-beam sustained discharges

    Science.gov (United States)

    Turner, Miles

    2016-09-01

    There are many emerging applications that exploit the exotic chemical characteristics of plasmas. Some of these applications, if deployed on an industrial scale, involve processing much larger volumes of gas than seems reasonable using any atmospheric pressure plasma source in wide use today. We note that an electron-beam sustained discharge permits the creation of a atmospheric pressure plasma with reasonable uniformity, large volme, and widely controllable electron temperature. Robust and durable electron beam sources now exist that would facilitate such applications. In this paper we discuss the general advantages of this approach, and we present a modelling study concerned with the production of NO in mixtures of N2 and O2, looking towards plasma aided manufacturing of fertilizers.

  6. Dielectric barrier discharge plasma treatment of cellulose nanofibre surfaces

    DEFF Research Database (Denmark)

    Kusano, Yukihiro; Madsen, Bo; Berglund, Linn

    2017-01-01

    on the nanofibre surface. Ultrasonic irradiation further enhanced the wetting and oxidation of the nanofibre coating. Scanning electron microscopic observations showed skeleton-like features on the plasma-treated surface, indicating preferential etching of weaker domains, such as low-molecular weight domains......Dielectric barrier discharge plasma treatment was applied to modify cellulose nanofibre (CNF) surfaces with and without ultrasonic irradiation. The plasma treatment improved the wetting by deionised water and glycerol, and increased the contents of oxygen, carbonyl group, and carboxyl group...... and amorphous phases. Ultrasonic irradiation also improved the uniformity of the treatment. Altogether, it is demonstrated that atmospheric pressure plasma treatment is a promising technique to modify the CNF surface before composite processing....

  7. Manufacturing of Dielectric Barrier Discharge Plasma Actuator for Degradation Resistance

    Science.gov (United States)

    Houser, Nicole M.

    The performance and broader application of dielectric barrier discharge (DBD) plasma actuators are restricted by the manufacturing methods currently employed. In the current work, two methodologies are proposed to build robust plasma actuators for active flow control; a protective silicone oil (PDMS) treatment for hand-cut and laid tape-based actuators and a microfabrication technique for glass-based devices. The microfabrication process, through which thin film electrodes are precisely deposited onto plasma-resistant glass substrates, is presented in detail. The resulting glass-based devices are characterized with respect to electrical properties and output for various operating conditions. The longevity of microfabricated devices is compared against silicone-treated and untreated hand-made devices of comparable geometries over 60 hours of continuous operation. Both tungsten and copper electrodes are considered for microfabricated devices. Human health effects are also considered in an electromagnetic field study of the area surrounding a live plasma actuator for various operating conditions.

  8. Autonomous Method and System for Minimizing the Magnitude of Plasma Discharge Current Oscillations in a Hall Effect Plasma Device

    Science.gov (United States)

    Hruby, Vladimir (Inventor); Demmons, Nathaniel (Inventor); Ehrbar, Eric (Inventor); Pote, Bruce (Inventor); Rosenblad, Nathan (Inventor)

    2014-01-01

    An autonomous method for minimizing the magnitude of plasma discharge current oscillations in a Hall effect plasma device includes iteratively measuring plasma discharge current oscillations of the plasma device and iteratively adjusting the magnet current delivered to the plasma device in response to measured plasma discharge current oscillations to reduce the magnitude of the plasma discharge current oscillations.

  9. An investigation of an underwater steam plasma discharge as alternative to air plasmas for water purification

    Science.gov (United States)

    Gucker, Sarah N.; Foster, John E.; Garcia, Maria C.

    2015-10-01

    An underwater steam plasma discharge, in which water itself is the ionizing media, is investigated as a means to introduce advanced oxidation species into contaminated water for the purpose of water purification. The steam discharge avoids the acidification observed with air discharges and also avoids the need for a feed gas, simplifying the system. Steam discharge operation did not result in a pH changes in the processing of water or simulated wastewater, with the actual pH remaining roughly constant during processing. Simulated wastewater has been shown to continue to decompose significantly after steam treatment, suggesting the presence of long-lived plasma produced radicals. During steam discharge operation, nitrate production is limited, and nitrite production was found to be below the detection threshold of (roughly 0.2 mg L-1). The discharge was operated over a broad range of deposited power levels, ranging from approximately 30 W to 300 W. Hydrogen peroxide production was found to scale with increasing power. Additionally, the hydrogen peroxide production efficiency of the discharge was found to be higher than many of the rates reported in the literature to date.

  10. Particle based plasma simulation for an ion engine discharge chamber

    Science.gov (United States)

    Mahalingam, Sudhakar

    Design of the next generation of ion engines can benefit from detailed computer simulations of the plasma in the discharge chamber. In this work a complete particle based approach has been taken to model the discharge chamber plasma. This is the first time that simplifying continuum assumptions on the particle motion have not been made in a discharge chamber model. Because of the long mean free paths of the particles in the discharge chamber continuum models are questionable. The PIC-MCC model developed in this work tracks following particles: neutrals, singly charged ions, doubly charged ions, secondary electrons, and primary electrons. The trajectories of these particles are determined using the Newton-Lorentz's equation of motion including the effects of magnetic and electric fields. Particle collisions are determined using an MCC statistical technique. A large number of collision processes and particle wall interactions are included in the model. The magnetic fields produced by the permanent magnets are determined using Maxwell's equations. The electric fields are determined using an approximate input electric field coupled with a dynamic determination of the electric fields caused by the charged particles. In this work inclusion of the dynamic electric field calculation is made possible by using an inflated plasma permittivity value in the Poisson solver. This allows dynamic electric field calculation with minimal computational requirements in terms of both computer memory and run time. In addition, a number of other numerical procedures such as parallel processing have been implemented to shorten the computational time. The primary results are those modeling the discharge chamber of NASA's NSTAR ion engine at its full operating power. Convergence of numerical results such as total number of particles inside the discharge chamber, average energy of the plasma particles, discharge current, beam current and beam efficiency are obtained. Steady state results for

  11. Studying surface glow discharge for application in plasma aerodynamics

    Science.gov (United States)

    Tereshonok, D. V.

    2014-02-01

    Surface glow discharge in nitrogen between two infinite planar electrodes occurring on the same plane has been studied in the framework of a diffusion-drift model. Based on the results of numerical simulations, the plasma structure of this discharge is analyzed and the possibility of using it in plasma aerodynamics is considered.

  12. "Super-acceleration" of ions in a stationary plasma discharge

    Science.gov (United States)

    Bardakov, Vladimir; Ivanov, Sergey; Kazantsev, Alexander; Strokin, Nikolay; Stupin, Aleksey

    2016-10-01

    We report on the detection of the acceleration effect of the bulk of ions in a stationary plasma E × B discharge to energies exceeding considerably the value equivalent to the discharge voltage. We determined the conditions necessary for the generation of high-energy ions, and ascertained the influence exerted on the value of the ion energies by pressure (flow rate) and the kind of plasma-producing gas, and by the value of discharge current. The possible acceleration mechanism is suggested.

  13. Physics and Chemistry of MW Laser-induced Discharge in Gas Flows and Plasma Jets

    Science.gov (United States)

    2007-12-01

    can be quasi-stationary coaxial plasma accelerators (MPC). This type of accelerators generates plasma jets of different gases (H2, He, N2, Ar) with...gas is ionizing and accelerating in discharge processing. For this regime the plasma gun generates the plasma jets of different gases3 (H2, He, N2...spectrometers. Spectrometers 1 and 2 are used for measuring of time behavior of single spectral lines, emitting in the focus area of plasma gun . Usually

  14. Parameters influencing plasma column potential in a reflex discharge

    Science.gov (United States)

    Liziakin, G. D.; Gavrikov, A. V.; Murzaev, Y. A.; Usmanov, R. A.; Smirnov, V. P.

    2016-12-01

    Distribution of electrostatic potential in direct current reflex discharge plasma has been studied experimentally. Measurements have been conducted by the single floating probe method. The influence of 0-0.2 T magnetic field, 1-200 mTorr pressure, 0-2 kV discharge voltage, and electrodes geometry on plasma column electrostatic potential was investigated. The possibility for the formation of a preset potential profile required for the realization of plasma separation of spent nuclear fuel was demonstrated.

  15. Morphological processing of ultraviolet emissions of electrical corona discharge for analysis and diagnostic use.

    Science.gov (United States)

    Schubert, Matthew; Moore, Andrew J

    2016-03-01

    Electron cascades from electrical discharge produce secondary emissions from atmospheric plasma in the ultraviolet band. For a single point of discharge, these emissions exhibit a stereotypical discharge morphology, with latent information about the discharge location. Morphological processing can uncover the location and therefore have diagnostic utility.

  16. Morphological Processing of Ultraviolet Emissions of Electrical Corona Discharge for Analysis and Diagnostic Use

    Science.gov (United States)

    Schubert, Matthew R.; Moore, Andrew J.

    2015-01-01

    Electron cascades from electrical discharge produce secondary emissions from atmospheric plasma in the ultraviolet band. For a single point of discharge, these emissions exhibit a stereotypical discharge morphology, with latent information about the discharge location. Morphological processing can uncover the location and therefore can have diagnostic utility.

  17. Dielectric barrier discharge plasma induced degradation of aqueous atrazine.

    Science.gov (United States)

    Feng, Jingwei; Jiang, Lin; Zhu, Dan; Su, Kuizu; Zhao, Dayong; Zhang, Jibiao; Zheng, Zheng

    2016-05-01

    Degradation of herbicide atrazine in aqueous solution was investigated using a plate type dielectric barrier discharge (DBD) plasma reactor. DBD plasma was generated at the gas-liquid interface of the formed water film. At discharge time of 14 min, atrazine was degradated effectively with a degradation rate of 99 % at the discharge power of 200 W. The experimental data fitted well with first-order kinetics and the energy efficiency for 90 % degradation of atrazine (G value) was calculated, obtaining a rate constant of 0.35 min(-1) and a G value of 1.27 × 10(-10) mol J(-1) (98.76 mg kW(-1) h(-1)) at a discharge power of 200 W, respectively. The addition of Fe(2+) increased the rate constant and G value dramatically, and a significant decrease of the rate constant and G value was observed with the addition of radical scavengers (tert-butyl alcohol, isopropyl alcohol, or Na2CO3). The generated aqueous O3 and H2O2 were determined, which promoted the degradation of herbicide atrazine. Dechlorination was observed and the experimentally detected Cl(-) was 1.52 mg L(-1) at a discharge time of 14 min. The degradation intermediates of atrazine were detected by means of liquid chromatography-mass spectrometry; dechlorination, hydroxylation, dealkylation, and alkyl oxidation processes were involved in the degradation pathways of atrazine.

  18. Discharge effects on gas flow dynamics in a plasma jet

    Science.gov (United States)

    Xian, Yu Bin; Hasnain Qaisrani, M.; Yue, Yuan Fu; Lu, Xin Pei

    2016-10-01

    Plasma is used as a flow visualization method to display the gas flow of a plasma jet. Using this method, it is found that a discharge in a plasma jet promotes the transition of the gas flow to turbulence. A discharge at intermediate frequency (˜6 kHz in this paper) has a stronger influence on the gas flow than that at lower or higher frequencies. Also, a higher discharge voltage enhances the transition of the gas flow to turbulence. Analysis reveals that pressure modulation induced both by the periodically directed movement of ionized helium and Ohmic heating on the gas flow plays an important role in inducing the transition of the helium flow regime. In addition, since the modulations induced by the high- and low-frequency discharges are determined by the frequency-selective effect, only intermediate-frequency (˜6 kHz) discharges effectively cause the helium flow transition from the laminar to the turbulent flow. Moreover, a discharge with a higher applied voltage makes a stronger impact on the helium flow because it generates stronger modulations. These conclusions are useful in designing cold plasma jets and plasma torches. Moreover, the relationship between the discharge parameters and the gas flow dynamics is a useful reference on active flow control with plasma actuators.

  19. Plasma processing for VLSI

    CERN Document Server

    Einspruch, Norman G

    1984-01-01

    VLSI Electronics: Microstructure Science, Volume 8: Plasma Processing for VLSI (Very Large Scale Integration) discusses the utilization of plasmas for general semiconductor processing. It also includes expositions on advanced deposition of materials for metallization, lithographic methods that use plasmas as exposure sources and for multiple resist patterning, and device structures made possible by anisotropic etching.This volume is divided into four sections. It begins with the history of plasma processing, a discussion of some of the early developments and trends for VLSI. The second section

  20. Electric plasma discharge combustion synthesis of chlorine dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Dotson, R. L.; Geren, G. W.

    1984-09-18

    A process for the production of chlorine dioxide comprises feeding an inert gas to a reaction zone and applying an electrical discharge to the inert gas to produce a high temperature plasma. Chlorine gas and oxygen gas are supplied simultaneously to the reaction zone and reacted in the plasma to produce a gaseous mixture comprised of chlorine dioxide, chlorine, oxygen and inert gas, the molar ratio of oxygen to chlorine in the reaction zone being at least about 2.5;1. The gaseous mixture is recovered from the reaction zone. Chlorine dioxide, which may be recovered as a gas or reacted to produce an alkali metal chlorite, is employed as a bleaching agent and a water treatment agent.

  1. Direct current dielectric barrier assistant discharge to get homogeneous plasma in capacitive coupled discharge

    Energy Technology Data Exchange (ETDEWEB)

    Du, Yinchang, E-mail: ycdu@mail.ustc.edu.cn [Modern Physics Department, University of Science and Technology of China, Hefei, Anhui 230026 (China); Max-Planck Institute for Extraterrestrial Physics, D-85748 Garching (Germany); Li, Yangfang [Max-Planck Institute for Extraterrestrial Physics, D-85748 Garching (Germany); Cao, Jinxiang; Liu, Yu; Wang, Jian; Zheng, Zhe [Modern Physics Department, University of Science and Technology of China, Hefei, Anhui 230026 (China)

    2014-06-15

    In this paper, we propose a method to get more homogeneous plasma in the geometrically asymmetric capacitive coupled plasma (CCP) discharge. The dielectric barrier discharge (DBD) is used for the auxiliary discharge system to improve the homogeneity of the geometrically asymmetric CCP discharge. The single Langmuir probe measurement shows that the DBD can increase the electron density in the low density volume, where the DBD electrodes are mounted, when the pressure is higher than 5 Pa. By this manner, we are able to improve the homogeneity of the plasma production and increase the overall density in the target volume. At last, the finite element simulation results show that the DC bias, applied to the DBD electrodes, can increase the homogeneity of the electron density in the CCP discharge. The simulation results show a good agreement with the experiment results.

  2. Multifunctional bulk plasma source based on discharge with electron injection

    Energy Technology Data Exchange (ETDEWEB)

    Klimov, A. S.; Medovnik, A. V. [Tomsk State University of Control Systems and Radioelectronics, Tomsk 634050 (Russian Federation); Tyunkov, A. V. [Tomsk State University of Control Systems and Radioelectronics, Tomsk 634050 (Russian Federation); Institute of High Current Electronics, Tomsk 634055 (Russian Federation); Savkin, K. P.; Shandrikov, M. V.; Vizir, A. V. [Institute of High Current Electronics, Tomsk 634055 (Russian Federation)

    2013-01-15

    A bulk plasma source, based on a high-current dc glow discharge with electron injection, is described. Electron injection and some special design features of the plasma arc emitter provide a plasma source with very long periods between maintenance down-times and a long overall lifetime. The source uses a sectioned sputter-electrode array with six individual sputter targets, each of which can be independently biased. This discharge assembly configuration provides multifunctional operation, including plasma generation from different gases (argon, nitrogen, oxygen, acetylene) and deposition of composite metal nitride and oxide coatings.

  3. Effect of Electric Discharge on Properties of Nano-Particulate Catalyst for Plasma-Catalysis.

    Science.gov (United States)

    Lee, Chung Jun; Kim, Jip; Kim, Taegyu

    2016-02-01

    Heterogeneous catalytic processes have been used to produce hydrogen from hydrocarbons. However, high reforming temperature caused serious catalyst deteriorations and low energy efficiency. Recently, a plasma-catalyst hybrid process was used to reduce the reforming temperature and to improve the stability and durability of reforming catalysts. Effect of electric discharges on properties of nanoparticulate catalysts for plasma-catalysis was investigated in the present study. Catalyst-bed porosity was varied by packing catalyst beads with the different size in a reactor. Discharge power and onset voltage of the plasma were measured as the catalyst-bed porosity was varied. The effect of discharge voltage, frequency and voltage waveforms such as the sine, pulse and square was investigated. We found that the optimal porosity of the catalyst-bed exists to maximize the electric discharge. At a low porosity, the electric discharge was unstable to be sustained because the space between catalysts got narrow nearly close to the sheath region. On the other hand, at a high porosity, the electric discharge became weak because the plasma was not sufficient to interact with the surface of catalysts. The discharge power increased as the discharge voltage and frequency increased. The square waveform was more efficient than the sine and pulse one. At a high porosity, however, the effect of the voltage waveform was not considerable because the space between catalysts was too large for plasma to interact with the surface of catalysts.

  4. Benzene conversion by manganese dioxide assisted silent discharge plasma

    Institute of Scientific and Technical Information of China (English)

    LU Bin; JI Min; YU Xin; FENG Tao; YAO Shuiliang

    2007-01-01

    Non-thermal plasma technologies have shown their promising potential specially for the low concentration of volatile organic compound control in indoor air in recent years.But it is also high energy consuming.So,to improve the energy efficiency,adding catalysts which enhance the plasma chemical reactions to plasma reactors may be a good selection.Therefore,in this study the manganese dioxide assisted silent discharge plasma was developed for benzene conversion at a relatively high energy efficiency.The results show that MnO2 could promote complete oxidation of benzene with O2 and O3 produced in the plasma discharge zone.The energy efficiency of benzene conversion with MnO2 was two folds as much as that without catalysts.It was also found that the site of MnO2 in the reactor and the energy density had effects on benzene conversion.While the energy density was lower than 48 J/L,benzene conversion decreased with the increase in the distance between MnO2 bed and the plasma discharge zone.Whereas when the energy density was higher than 104 J/L,benzene conversion had an optimal value that was governed by the distance between MnO2 bed and the plasma discharge zone.The mechanism of benzene oxidation in plasma discharges and over MnO2 is discussed in detail.

  5. Plasma Physics Issues in Gas Discharge Laser Development

    Science.gov (United States)

    1991-12-01

    WL-TR-92-2087 PLASMA PHYSICS ISSUES IN GAS DISCHARGE LASER DEVELOPMENT AD-A257 735 ALAN GARSCADDEN MARK J. KUSNER J. GARY EDEN WL/POOC-3 WRIGHT...LASERS INFRARED MOLECULAR jAS LASERS UNCLASSIFIED UNCLASSIFIED UNCLASSIFIED UL Plasma Physics Issues in Gas Discharge Laser Development Alan Garscadden...the close coupling between body of work was not generally useful in laser development . vibrationally excited nitrogen and CO or CO2 . In fact. the First

  6. Plasmas in Multiphase Media: Bubble Enhanced Discharges in Liquids and Plasma/Liquid Phase Boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Kushner, Mark Jay [University of Michigan

    2014-07-10

    In this research project, the interaction of atmospheric pressure plasmas with multi-phase media was computationally investigated. Multi-phase media includes liquids, particles, complex materials and porous surfaces. Although this investigation addressed fundamental plasma transport and chemical processes, the outcomes directly and beneficially affected applications including biotechnology, medicine and environmental remediation (e.g., water purification). During this project, we made advances in our understanding of the interaction of atmospheric pressure plasmas in the form of dielectric barrier discharges and plasma jets with organic materials and liquids. We also made advances in our ability to use computer modeling to represent these complex processes. We determined the method that atmospheric pressure plasmas flow along solid and liquid surfaces, and through endoscopic like tubes, deliver optical and high energy ion activation energy to organic and liquid surfaces, and produce reactivity in thin liquid layers, as might cover a wound. We determined the mechanisms whereby plasmas can deliver activation energy to the inside of liquids by sustaining plasmas in bubbles. These findings are important to the advancement of new technology areas such as plasma medicine

  7. Focused beams of fast neutral atoms in glow discharge plasma

    Science.gov (United States)

    Grigoriev, S. N.; Melnik, Yu. A.; Metel, A. S.; Volosova, M. A.

    2017-06-01

    Glow discharge with electrostatic confinement of electrons in a vacuum chamber allows plasma processing of conductive products in a wide pressure range of p = 0.01 - 5 Pa. To assist processing of a small dielectric product with a concentrated on its surface beam of fast neutral atoms, which do not cause charge effects, ions from the discharge plasma are accelerated towards the product and transformed into fast atoms. The beam is produced using a negatively biased cylindrical or a spherical grid immersed in the plasma. Ions accelerated by the grid turn into fast neutral atoms at p > 0.1 Pa due to charge exchange collisions with gas atoms in the space charge sheaths adjoining the grid. The atoms form a diverging neutral beam and a converging beam propagating from the grid in opposite directions. The beam propagating from the concave surface of a 0.24-m-wide cylindrical grid is focused on a target within a 10-mm-wide stripe, and the beam from the 0.24-m-diameter spherical grid is focused within a 10-mm-diameter circle. At the bias voltage U = 5 kV and p ˜ 0.1 Pa, the energy of fast argon atoms is distributed continuously from zero to eU ˜ 5 keV. The pressure increase to 1 Pa results in the tenfold growth of their equivalent current and a decrease in the mean energy by an order of magnitude, which substantially raises the efficiency of material etching. Sharpening by the beam of ceramic knife-blades proved that the new method for the generation of concentrated fast atom beams can be effectively used for the processing of dielectric materials in vacuum.

  8. Breakdown transient study of plasma distributions in a 2.45 GHz hydrogen discharge

    Energy Technology Data Exchange (ETDEWEB)

    Cortázar, O.D., E-mail: daniel.cortazar@uclm.es [Universidad de Castilla-La Mancha, ETSII-INEI, Applied Mechanics and Projects Department, C.J. Cela s/n, 13170 Ciudad Real (Spain); Megía-Macías, A. [ESS Bilbao Consortium, Polígono Ugaldeguren-III Pol. A 7B, 48170-Zamudio, Vizcaya (Spain); Tarvainen, O.; Koivisto, H. [University of Jyväskylä, Department of Physics, PO Box 35 (YFL), 40500 Jyväskylä (Finland)

    2015-05-01

    Plasma distribution transients associated with the breakdown of a 2.45 GHz hydrogen discharge similar to high current microwave ion sources are studied by means of an ultra-fast frame image acquisition system in visible light range. Eight different plasma distributions have been studied by photographing the 2D projections of the discharge through a transparent plasma electrode. The temporal evolution of images in Balmer-alpha and Fulcher band wavelengths have been recorded associated to atomic and molecular excitation and ionization processes. Some unexpected plasma distributions transient behaviors during breakdown are reported.

  9. Plasma Acceleration from RF Discharge in Dielectric Capillary

    Energy Technology Data Exchange (ETDEWEB)

    A. Dunaevsky; Y. Raitses; N. J. Fisch

    2005-08-09

    Plasma acceleration from rf discharge in dielectric capillary was demonstrated. Observed plasma flow had ion energies of approximately 100 eV and electron energies of approximately 20 eV. The discharge was powered by a MHz-range rf generator and fed by Ar. Experimental results indicate possible validity of assumptions about formation of a potential difference at the open end of the capillary and presence of hot electron fraction in the capillary discharge. Simplicity and small dimensions of the source are attractive for micro-propulsion applications.

  10. Conversion of Methane by Dielectric-barrier Discharge Plasma Method-Comparison with Microwave Plasma Method

    National Research Council Canada - National Science Library

    Konno, Katsuya; Kobayashi, Motoki; Onoe, Kaoru; Yamaguchi, Tatsuaki

    2010-01-01

      Methane conversion by the dielectric-barrier discharge plasma method (DBD) was compared with our previous findings for the microwave plasma method (MW). The power (Pw), initial pressure (P0) and flow rate (F0...

  11. The energy distribution structure and dynamic characteristics of energy release in electrostatic discharge process

    CERN Document Server

    Liu, Qingming; Zhang, Yunming

    2015-01-01

    The detail structure of energy output and the dynamic characteristics of electric spark discharge process have been studied to calculate the energy of electric spark induced plasma under different discharge condition accurately. A series of electric spark discharge experiments were conducted with the capacitor stored energy in the range of 10J 100J and 1000J respectively. And the resistance of wire, switch and plasma between electrodes were evaluated by different methods. An optimized method for electric resistance evaluation of the full discharge circuit, three poles switch and electric spark induced plasma during the discharge process was put forward. The electric energy consumed by wire, electric switch and electric spark induced plasma between electrodes were obtained by Joules law. The structure of energy distribution and the dynamic process of energy release during the capacitor discharge process have been studied. Experiments results showed that, with the increase of capacitor released energy, the dura...

  12. Pathway Study on Dielectric Barrier Discharge Plasma Conversion of Hexane

    NARCIS (Netherlands)

    Agiral, Anil; Boyadjian, Cassia; Seshan, K.; Lefferts, Leon; Gardeniers, J.G.E. (Han)

    2010-01-01

    A plasma reactor based on dielectric barrier discharge has been developed for oxidative cracking of hexane to yield olefins at atmospheric pressure. Dissociation of hexane in the presence of oxygen with nonequilibrium plasma state represents complex chemistry, and both conversion and product selecti

  13. Improvement on Diamond Nucleation Treated by Pulsed Arc Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    马志斌; 万军; 汪建华; 张文文

    2004-01-01

    A technique of improvement on diamond nucleation based on pulsed arc discharge plasma at atmospheric pressure was developed. The pulsed arc discharge was induced respectively by nitrogen, argon and methanol gas. After the arc plasma pretreatment, a nucleation density higher than 1010 cm-2 may be obtained subsequently in chemical vapor deposition (CVD) on a mirror-polished silicon substrate without any other mechanical treatment. The effects of the arc discharge plasma on the diamond nucleation were investigated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), infrared spectroscopy (IR) and Raman spectroscopy. The enhancement of nucleation is postulated to be a result of the formation of carbonlike phase materials or nitrogenation on the substrate surface without surface defect produced by arc discharge.

  14. Current evolution and plasma density space distribution in the reflex discharge with ring cathodes

    Science.gov (United States)

    Samokhin, A. A.; Liziakin, G. D.; Gavrikov, A. V.; Usmanov, R. A.; Smirnov, V. P.

    2016-11-01

    In this paper the numerical model of direct current gas discharge in drift-diffusion approximation is considered. For two-component plasma the processes of the gas discharge development in the reflex geometry with ring cathodes at a helium pressure of 35 mTorr are studied. We investigate the influence of: (a) the boundary conditions on the dielectric, (b) the electron temperature and (c) the coefficient of the secondary ion-electron emission on the I-U curve of the discharge. In a magnetic field of 50 Gauss the impact of the discharge voltage U = 300-700 V on the evolutionary process of the discharge is examined. The effect of diffusion on maintaining steady state discharge is researched. The parameters of the existence of a high-current (tens of μA) and low voltage (tens of mA) discharge modes are defined.

  15. Interplay of discharge and gas flow in atmospheric pressure plasma jets

    Science.gov (United States)

    Jiang, Nan; Yang, JingLong; He, Feng; Cao, Zexian

    2011-05-01

    Interplay of discharge and gas flow in the atmospheric pressure plasma jets generated with three different discharge modes [N. Jiang, A. L. Ji, and Z. X. Cao, J. Appl. Phys. 106, 013308 (2009); N. Jiang, A. L. Ji, and Z. X. Cao, J. Appl. Phys. 108, 033302 (2010)] has been investigated by simultaneous photographing of both plasma plumes and gas flows in the ambient, with the former being visualized by using an optical schlieren system. Gas flow gains a forward momentum from discharge except for the case of overflow jets at smaller applied voltages. Larger applied voltage implies an elongated plasma jet only for single-electrode mode; for dielectric barrier discharge jet the plume length maximizes at a properly applied voltage. These findings can help understand the underlying processes, and are useful particularly for the economic operation of tiny helium plasma jets and jet arrays.

  16. Flush-mounted probe diagnostics for argon glow discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Liang, E-mail: xld02345@mail.ustc.edu.cn; Cao, Jinxiang; Liu, Yu; Wang, Jian; Du, Yinchang; Zheng, Zhe; Zhang, Xiao; Wang, Pi [Department of Modern Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Zhang, Jin; Li, Xiao; Qin, Yongqiang; Zhao, Liang [Science and Technology on Space Physics Laboratory, Beijing 100076 (China)

    2014-09-15

    A comparison is made between plasma parameters measured by a flush-mounted probe (FP) and a cylindrical probe (CP) in argon glow discharge plasma. Parameters compared include the space potential, the plasma density, and the effective electron temperature. It is found that the ion density determined by the FP agrees well with the electron density determined by the CP in the quasi-neutral plasma to better than 10%. Moreover, the space potential and effective electron temperature calculated from electron energy distribution function measured by the FP is consistent with that measured by the CP over the operated discharge current and pressure ranges. These results present the FP can be used as a reliable diagnostic tool in the stable laboratory plasma and also be anticipated to be applied in other complicated plasmas, such as tokamaks, the region of boundary-layer, and so on.

  17. Unfiltered Diesel Engine Exhaust Treatment by Discharge Plasma:Effect of Soot Oxidation

    Institute of Scientific and Technical Information of China (English)

    B. S. Rajanikanth; Subhankar Das; A. D. Srinivasan

    2004-01-01

    A cascaded system of electrical discharges (Non-thermal plasma), catalyst and adsorption process was investigated for the removal of oxides of nitrogen (NO x) and carbon monoxide (CO) from a Diesel engine raw exhaust. The three processes were separately studied first, and then the cascaded processes, namely plasma-catalyst and plasma-adsorbent, were investigated. In this paper main emphasis was laid on the effect of carbonaceous soot oxidation on the plasma treatment process. While the cascaded plasma-catalyst process exhibits a higher CO removal, the cascaded plasma-adsorbent process exhibits a higher NO x removal. The experiments were conducted under no-load. The plasma and adsorbent reactors were kept at room temperature throughout the experiment while the catalyst reactor was kept at 200oC / 300oC.

  18. Heterogeneous sono-Fenton-like process using nanostructured pyrite prepared by Ar glow discharge plasma for treatment of a textile dye.

    Science.gov (United States)

    Khataee, Alireza; Gholami, Peyman; Vahid, Behrouz

    2016-03-01

    The plasma-treated pyrite (PTP) nanostructures were prepared from natural pyrite (NP) utilizing argon plasma due to its sputtering and cleaning effects resulting in more active surface area. The NP and PTP were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Brunauer-Emmett-Teller (BET) and scanning electron microscopy (SEM) methods. The performance of the PTP was greater than NP for treatment of Reactive Red 84 (RR84) by the heterogeneous sono-Fenton process. The optimum amounts of main operational parameters were obtained as PTP of 4 g/L, initial dye concentration of 10 mg/L, pH of 5, and ultrasonic power of 300 W after 120 min of reaction time. Also, the effects of enhancers, and inorganic salts and t-butanol as hydroxyl radical scavengers on the degradation efficiency were investigated. Gas chromatography-mass spectroscopy analysis (GC-MS) was applied for detection of some degradation intermediates. Environmentally friendly plasma modification of the NP, in situ production of H2O2 and OH radicals, low leached iron concentration and repeated reusability at the milder pH are the significant benefits of the PTP utilization.

  19. Experiments of discharge guiding using strongly and weakly ionized plasma channels for laser-triggered lightning

    Science.gov (United States)

    Shimada, Yoshinori; Uchida, Shigeaki; Yamanaka, Chiyoe; Ogata, Akihisa; Yamanaka, Tatsuhiko; Kawasaki, Zen-ichiro; Fujiwara, Etsuo; Ishikubo, Yuji; Kawabata, Kinya

    2000-01-01

    Generation of a long laser-plasma channel capable of triggering and guiding an electrical discharge is a crucial issue for laser-triggering protection system. We make a long plasma channel to increase the probability of triggered lightning by laser. To produce a long laser plasma channel, we propose da new technique called hybrid plasma channel method which combines weakly and strongly ionized plasma channels to maximize laser-energy efficiency of discharge guiding. We investigate the characteristics of the hybrid plasma channels to maximize laser-energy efficiency of discharge guiding. We investigate the characteristics of the hybrid plasma channel method through several laboratory experiments. The weakly ionized channel was generated by UV laser pulses in air. As the number density of electrons in weakly ionized channel is proportional to 1.1 power of laser intensity, nitrogen and oxygen molecules can not attributed to the source of ionized plasma. It is suggested that dissociation process of impurities in air whose density is 1011 - 1012 cm-3 plays an important role in plasma formation and leader triggering effect. The 50 percent flashover voltage using the hybrid plasma channel method is lower than that without the weakly ionized plasma channel. It was also found that higher repetition rate of the plasma generation on lowers the V50 furthermore.

  20. MERCURY OXIDIZATION IN NON-THERMAL PLASMA BARRIER DISCHARGE SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    V.K. Mathur

    2003-02-01

    In the past decade, the emission of toxic elements from human activities has become a matter of great public concern. Hg, As, Se and Cd typically volatilize during a combustion process and are not easily caught with conventional air pollution control techniques. In addition, there is no pollution prevention technique available now or likely be available in the foreseeable future that can prevent the emission of these trace elements. These trace elements pose additional scientific challenge as they are present at only ppb levels in large gas streams. Mercury, in particular, has attracted significant attention due to its high volatility, toxicity and potential threat to human health. In the present research work, a non-thermal plasma dielectric barrier discharge technique has been used to oxidize Hg{sup 0}(g) to HgO. The basic premise of this approach is that Hg{sup 0} in vapor form cannot be easily removed in an absorption tower whereas HgO as a particulate is amiable to water scrubbing. The work presented in this report consists of three steps: (1) setting-up of an experimental apparatus to generate mercury vapors at a constant rate and modifying the existing non-thermal plasma reactor system, (2) solving the analytical challenge for measuring mercury vapor concentration at ppb level, and (3) conducting experiments on mercury oxidation under plasma conditions to establish proof of concept.

  1. Pattern phenomena in an rf discharge dusty plasma system

    Institute of Scientific and Technical Information of China (English)

    HUANG Feng; YE Maofu; WANG Long

    2006-01-01

    Various dust patterns are observed in an rf discharge dusty plasma system.According to the dust growth process from small to large in size, the formation of different dust patterns can be divided into two stages: the small-particle stage (or dust cloud stage),and the large-particle stage (or dust crystal stage). The evolution relations between different dust patterns with gas pressure changing are investigated. Dust voids, dust acoustic waves and strong turbulence modes are presented at the small-particle stage. The self-organized dust lattices and dust clusters are investigated at the large-particle stage.The static structure of a dust lattice is characterized by means of the pair correlation function. Dust clusters formed by particles with different numbers and the regular evolution of the clusters with gas pressure are also investigated. The packing sequences of dust clusters are verified through two-dimensional confined molecular dynamics simulations.

  2. Plasma chemistry in an atmospheric pressure Ar/NH3 dielectric barrier discharge

    DEFF Research Database (Denmark)

    Fateev, A.; Leipold, F.; Kusano, Y.

    2005-01-01

    An atmospheric pressure dielectric barrier discharge (DBD) in Ar/NH3 (0.1 - 10%) mixtures with a parallel plate electrode geometry was studied. The plasma was investigated by emission and absorption spectroscopy in the UV spectral range. Discharge current and voltage were measured as well. UV...... absorption spectroscopy was also employed for the detection of stable products in the exhaust gas. To clarify the different processes for ammonia decomposition, N-2(2 - 10%) was added to the plasma. Modeling of the chemical kinetics in an Ar/NH3 plasma was performed as well. The dominant stable products...... of an atmospheric pressure Ar/NH3 DBD are H-2, N-2 and N2H4. The hydrazine (N2H4) concentration in the plasma and in the exhaust gases at various ammonia concentrations and different discharge powers was measured. Thermal N2H4 decomposition into NH2 radicals may be used for NOx reduction processes....

  3. Large Scale Modelling of Glow Discharges or Non - Plasmas

    Science.gov (United States)

    Shankar, Sadasivan

    The Electron Velocity Distribution Function (EVDF) in the cathode fall of a DC helium glow discharge was evaluated from a numerical solution of the Boltzmann Transport Equation(BTE). The numerical technique was based on a Petrov-Galerkin technique and a unique combination of streamline upwinding with self -consistent feedback-based shock-capturing. EVDF for the cathode fall was solved at 1 Torr, as a function of position x, axial velocity v_{rm x}, radial velocity v_{rm r}, and time t. The electron-neutral collisions consisted of elastic, excitation, and ionization processes. The algorithm was optimized and vectorized to speed execution by more than a factor of 10 on CRAY-XMP. Efficient storage schemes were used to save the memory allocation required by the algorithm. The analysis of the solution of BTE was done in terms of the 8-moments that were evaluated. Higher moments were found necessary to study the momentum and energy fluxes. The time and length scales were estimated and used as a basis for the characterization of DC glow discharges. Based on an exhaustive study of Knudsen numbers, it was observed that the electrons in the cathode fall were in the transition or Boltzmann regime. The shortest relaxation time was the momentum relaxation and the longest times were the ionization and energy relaxation times. The other times in the processes were that for plasma reaction, diffusion, convection, transit, entropy relaxation, and that for mean free flight between the collisions. Different models were classified based on the moments, time scales, and length scales in their applicability to glow discharges. These consisted of BTE with different number af phase and configuration dimensions, Bhatnagar-Gross-Krook equation, moment equations (e.g. Drift-Diffusion, Drift-Diffusion-Inertia), and spherical harmonic expansions.

  4. Ignition Features of Plasma-Beam Discharge in Gas-Discharge Electron Gun Operation

    Directory of Open Access Journals (Sweden)

    Valery A. Tutyk

    2013-01-01

    Full Text Available The current paper presents the results of experimental researches to determine the mode features of plasma-beam discharge (PBD generation by an electron beam injected by a low-vacuum gasdischarge electron gun (LGEG with the cold cathode and hollow anode on the basis of the high-voltage glow discharge and in the range of helium pressure of P ? 10 ÷ 130 Pa. The PBD boundaries and their dependences on parameters of an electron beam are found. The influence of PBD on parameters of low-vacuum gas-discharge electron gun is revealed. It causes an avalanche increase of electron beam current and burning of plasma-beam discharge in the whole space of the vacuum chamber volume and generation of electromagnetic radiation is revealed. Achieved results will be used for implementation of various vacuum technologies in the medium of reaction gas and generated electromagnetic radiation.

  5. Evaluation of the potentials of humic acid removal in water by gas phase surface discharge plasma.

    Science.gov (United States)

    Wang, Tiecheng; Qu, Guangzhou; Ren, Jingyu; Yan, Qiuhe; Sun, Qiuhong; Liang, Dongli; Hu, Shibin

    2016-02-01

    Degradation of humic acid (HA), a predominant type of natural organic matter in ground water and surface waters, was conducted using a gas phase surface discharge plasma system. HA standard and two surface waters (Wetland, and Weihe River) were selected as the targets. The experimental results showed that about 90.9% of standard HA was smoothly removed within 40 min's discharge plasma treatment at discharge voltage 23.0 kV, and the removal process fitted the first-order kinetic model. Roles of some active species in HA removal were studied by evaluating the effects of solution pH and OH radical scavenger; and the results presented that O3 and OH radical played significant roles in HA removal. Scanning electron microscope (SEM) and FTIR analysis showed that HA surface topography and molecular structure were changed during discharge plasma process. The mineralization of HA was analyzed by UV-Vis spectrum, dissolved organic carbon (DOC), specific UV absorbance (SUVA), UV absorption ratios, and excitation-emission matrix (EEM) fluorescence. The formation of disinfection by-products during HA sample chlorination was also identified, and CHCl3 was detected as the main disinfection by-product, but discharge plasma treatment could suppress its formation to a certain extent. In addition, approximately 82.3% and 67.9% of UV254 were removed for the Weihe River water and the Wetland water after 40 min of discharge plasma treatment.

  6. Thermal behavior of bovine serum albumin after exposure to barrier discharge helium plasma jet

    Science.gov (United States)

    Jijie, R.; Pohoata, V.; Topala, I.

    2012-10-01

    Non-thermal plasma jets at atmospheric pressure are useful tools nowadays in plasma medicine. Various applications are tested such as cauterization, coagulation, wound healing, natural and artificial surfaces decontamination, and sterilization. In order to know more about the effects of gas plasma on biological supramolecules, we exposed protein powders to a barrier discharge helium plasma jet. Then, spectroscopic investigations were carried out in order to obtain information on protein secondary, tertiary, and quaternary structures. We obtained a reduction of the protein alpha-helix content after the plasma exposure and a different behavior, for both thermal denaturation/renaturation kinetics and thermal aggregation process.

  7. Atmospheric Pressure Plasma Process And Applications

    Energy Technology Data Exchange (ETDEWEB)

    Peter C. Kong; Myrtle

    2006-09-01

    This paper provides a general discussion of atmospheric-pressure plasma generation, processes, and applications. There are two distinct categories of atmospheric-pressure plasmas: thermal and nonthermal. Thermal atmospheric-pressure plasmas include those produced in high intensity arcs, plasma torches, or in high intensity, high frequency discharges. Although nonthermal plasmas are at room temperatures, they are extremely effective in producing activated species, e.g., free radicals and excited state atoms. Thus, both thermal and nonthermal atmosphericpressure plasmas are finding applications in a wide variety of industrial processes, e.g. waste destruction, material recovery, extractive metallurgy, powder synthesis, and energy conversion. A brief discussion of recent plasma technology research and development activities at the Idaho National Laboratory is included.

  8. Plasma-density evolution in compact polyacetal capillary discharges

    Energy Technology Data Exchange (ETDEWEB)

    Tomasel, F.G.; Rocca, J.J.; Cortazar, O.D.; Szapiro, B.T. (Electrical Engineering Department, Colorado State University, Fort Collins, Colorado 80523 (United States)); Lee, R.W. (Lawrence Livermore National Laboratory, Livermore, California 94550 (United States))

    1993-05-01

    We have measured the temporal evolution of the electron density of plasmas produced in polyacetal capillaries with diameters between 0.5 and 1.5 mm excited by 110-ns full-width-at-half-maximum discharge pulses with currents between 13 and 42 kA. The electron density was determined from Stark-broadened line profiles of the 4[ital f]-3[ital d] O VI transition taking into account opacity effects. The electron density was found to increase continuously during the rise of the current pulse, and to decrease near the end of the current pulse, when a drop in plasma temperature causes the degree of ionization of the plasma to decrease. The peak plasma density in a 1-mm capillary excited by a 24-kA pulse was measured to be 5[times]10[sup 19] cm[sup [minus]3]. The plasma density was observed to increase linearly with discharge energy from 7.5[times]10[sup 18] cm[sup [minus]3] for a 5-J discharge to 5[times]10[sup 19] cm[sup [minus]3] for a 30-J discharge in a 1.5-mm-diam. capillary.

  9. Carbon dust particles in a beam-plasma discharge

    Science.gov (United States)

    Koval, O. A.; Vizgalov, V.; Shalpegin, A. V.

    2016-09-01

    This paper focuses on dynamics of micro-sized carbon dust grains in beam-plasma discharge (BPD) plasmas. It was demonstrated that injected dust particles can be captured and transported along the discharge. Longitudinal average velocity of the particles in the central area of the plasma column was 17 m/sec, and 2 m/sec in the periphery. Dust injection caused a decrease of emission intensity of metastable nitrogen molecular ion. This effect is suggested for a spectroscopy method for particles’ potential measurements. Five-micron radius carbon dust grains obtained potential above 500 V in the experiments on PR-2 installation, proving the feasibility of BPDs for the charging of fine dust particles up to high potential values, unattainable in similar plasma conditions.

  10. Formation of positive ions in hydrocarbon containing dielectric barrier discharge plasmas

    Science.gov (United States)

    Mihaila, Ilarion; Pohoata, Valentin; Jijie, Roxana; Nastuta, Andrei Vasile; Rusu, Ioana Alexandra; Topala, Ionut

    2016-12-01

    Low temperature atmospheric pressure plasma devices are suitable experimental solutions to generate transitory molecular environments with various applications. In this study we present experimental results regarding the plasma chemistry of dielectric barrier discharges (DBD) in helium - hydrogen (0.1%) - hydrocarbons (1.2%) mixtures. Four types of hydrocarbon gases were studied: methane (CH4), ethane (C2H6), propane (C3H8), and butane (C4H10). Discharge diagnosis and monitoring was assured by electrical measurements and optical emission spectroscopy. Molecular beam mass spectrometry is engaged to sample positive ions populations from two different plasma sources. Dissociation and generation of higher-chain and cyclic (aromatic) hydrocarbons were discussed as a function of feed gas and discharge geometry. We found a strong influence of these parameters on both molecular mass distribution and recombination processes in the plasma volume.

  11. Sterilization of Turmeric by Atmospheric Pressure Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Setareh, Salarieh; Davoud, Dorranian

    2013-11-01

    In this study atmospheric pressure dielectric barrier discharge (DBD) plasma has been employed for sterilizing dry turmeric powders. A 6 kV, 6 kHz frequency generator was used to generate plasma with Ar, Ar/O2, He, and He/O2 gases between the 5 mm gap of two quartz covered electrodes. The complete sterilization time of samples due to plasma treatment was measured. The most important contaminant of turmeric is bacillus subtilis. The results show that the shortest sterilization time of 15 min is achieved by exposing the samples to Ar/O2 plasma. Survival curves of samples are exponential functions of time and the addition of oxygen to plasma leads to a significant increase of the absolute value of time constant of the curves. Magnitudes of protein and DNA in treated samples were increased to a similar value for all samples. Taste, color, and solubility of samples were not changed after the plasma treatment.

  12. Destruction of Bacterial Biofilms Using Gas Discharge Plasma

    Science.gov (United States)

    Abramzon, Nina

    2005-03-01

    Biofilms are bacterial communities embedded in an exopolysaccharidic matrix with a complex architectural structure. Bacteria in biofilms show different properties from those in free life thus, conventional methods of killing bacteria are often ineffective with biofilms. The use of plasmas potentially offers an alternative to conventional sterilization methods since plasmas contain a mixture of charged particles, chemically reactive species, and UV radiation. 4 and 7 day-old biofilms were produced using two bacterial species: Rhizobium gallicum and Chromobacterium violaceum. Gas discharge plasma was produced by using an AtomfloTM reactor (Surfx Technologies) and bacterial biofilms were exposed to it for different periods of time. Our results show that a 10-minute plasma treatment was able to kill 100% of the cells in most cases. Optical emission spectroscopy was used to study plasma composition which is then correlated with the effectiveness of killing. These results indicate the potentiality of plasma as an alternative sterilization method. Supported by CSuperb.

  13. Low pressure arc discharges with hollow cathodes and their using in plasma generators and charged particle sources

    CERN Document Server

    Vintizenko, L G; Koval, N N; Tolkachev, V S; Lopatin, I V; Shchanin, P M

    2001-01-01

    Paper presents the results of investigation into arc discharges with a hollow cathode generating 10 sup 1 sup 0 -10 sup 1 sup 2 concentration gas-discharge plasma in essential (approx 1 m sup 3) volumes at low (10 sup - sup 2 -1 Pa) pressures and up to 200 A discharge currents. One studied design of discharge systems with heated and cold cathodes their peculiar features, presented the parameters of plasma generators and of charged particle sources based on arc discharges and discussed, as well, the problems of more rational application of those systems in the processes for surface modification of solids

  14. Dynamics of the plasma current sheath in plasma focus discharges in different gases

    Energy Technology Data Exchange (ETDEWEB)

    Vinogradov, V. P.; Krauz, V. I., E-mail: krauz-vi@nrcki.ru [National Research Center Kurchatov Institute (Russian Federation); Mokeev, A. N. [Project Center ITER (Russian Federation); Myalton, V. V.; Kharrasov, A. M. [National Research Center Kurchatov Institute (Russian Federation)

    2016-12-15

    The shape of the plasma current sheath (PCS) in the final stage of its radial compression, the dynamics of pinching, and the subsequent pinch decay in plasma focus (PF) discharges in different gases are studied using an improved multichannel system of electron-optical plasma photography and a newly elaborated synchronization system. The PCS structure in discharges in heavy gases (Ne, Ar) is found to differ significantly from that in discharges in hydrogen and deuterium. The influence of a heavy gas (Xe) additive to hydrogen and deuterium on the structure and compression dynamics of the PCS is investigated.

  15. Dielectric barrier discharge processing of aerospace materials

    Science.gov (United States)

    Scott, S. J.; Figgures, C. C.; Dixon, D. G.

    2004-08-01

    We report the use of atmospheric pressure, air based, dielectric barrier discharges (DBD) to treat materials commonly used in the aerospace industries. The material samples were processed using a test-bed of a conventional DBD configuration in which the sample formed one of the electrodes and was placed in close proximity to a ceramic electrode. The discharges generated a powerful, cold oxidizing environment which was able to remove organic contaminants, etch primer and paint layers, oxidize aluminium and roughen carbon fibre composites by the selective removal of resin.

  16. Dielectric barrier Discharge Plasma Actuator Characterization and Application

    NARCIS (Netherlands)

    Correale, G.

    2016-01-01

    An experimental investigation about nanosecond Dielectric Barrier Discharge (ns-DBD) plasma actuator is presented in this thesis. This work aimed to answer fundamental questions on the actuation mechanism of this device. In order to do so, parametric studies in a quiescent air as well as laminar

  17. Dielectric barrier Discharge Plasma Actuator Characterization and Application

    NARCIS (Netherlands)

    Correale, G.

    2016-01-01

    An experimental investigation about nanosecond Dielectric Barrier Discharge (ns-DBD) plasma actuator is presented in this thesis. This work aimed to answer fundamental questions on the actuation mechanism of this device. In order to do so, parametric studies in a quiescent air as well as laminar bou

  18. Plasma production by means of discharge in a spherical cavity

    NARCIS (Netherlands)

    Antsiferov, P. S.; Dorokhin, L. A.; Koshelev, K. N.

    2010-01-01

    The work is devoted to the study of plasma, appearing as a result of cumulation of shock wave with form close to spherical. The shock wave was obtained by triggering of fast discharge (dI/dt about 10(12) A/s) on inner surface of cavity, made from insulator. Spherical cavity with radius 4.5 mm was fi

  19. Characterization of Plasma Polymerized Hexamethyldisiloxane Films Prepared by Arc Discharge

    NARCIS (Netherlands)

    Lazauskas, A.; Baltrusaitis, Jonas; Grigaliunas, V.; Jucius, D; Guobiene, A.; Prosycevas, I.; Narmontas, P.

    2014-01-01

    Herein, we present a simple method for fabricating plasma polymerized hexamethyldisiloxane films (pp-HMDSO) possessing superhydrophobic characteristics via arc discharge. The pp-HMDSO films were deposited on a soda–lime–silica float glass using HMDSO monomer vapor as a precursor. A detailed surface

  20. Research on the Plasma Anemometer Based on AC Glow Discharge

    Directory of Open Access Journals (Sweden)

    Bing Yu

    2017-01-01

    Full Text Available A new plasma anemometer based on AC glow discharge is designed in this article. Firstly, theoretical analysis of plasma anemometer working principle is introduced to prove the feasibility of the experimental measurement method. Then the experiments are carried out to study the effects of different parameters on the static discharge characteristics of the plasma anemometer system, by which the system optimization methods are obtained. Finally, several groups of appropriate parameters are selected to build the plasma anemometer system based on resistance capacitance coupling negative feedback AC glow discharge, and different airflow speeds are applied to obtain the achievable velocity measurement range. The results show that there is a linear relationship between airflow velocity and discharge current in an allowable error range, which can be applied for airflow velocity measurement. Negative feedback coupling module, which is composed of the coupling resistance and the coupling capacitance, has good effects on improving the system stability. The measurement range of the airflow velocity is significantly increased when the electrode gap is 3 mm, coupling resistance is 470 Ω, and coupling capacitance is 220 pF.

  1. Electrohydrodynamic force in dielectric barrier discharge plasma actuators

    Energy Technology Data Exchange (ETDEWEB)

    Boeuf, J P; Lagmich, Y; Unfer, Th; Callegari, Th; Pitchford, L C [CPAT-CNRS, Universite Paul Sabatier, 118 Route de Narbonne, Toulouse 31062 (France)

    2007-02-07

    Surface dielectric barrier discharges (DBDs) have been proposed as actuators for flow control. In this paper we discuss the basic mechanisms responsible for the electrohydrodynamic (EHD) force exerted by the discharge on the gas molecules. A two-dimensional fluid model of the DBD is used to describe the plasma dynamics, to understand the basic physics associated with the EHD force and to give some quantitative estimation of the force under simplified conditions. The results show that for ramp or sinusoidal voltage waveforms, the discharge consists of large amplitude short current pulses during which a filamentary plasma spreads along the surface, separated in time by long duration, low current discharge phases of a Townsend or corona type. The contribution of the low current phases to the total force exerted by the discharge on the gas is dominant because their duration is much longer than that of the current pulses and because the force takes place in a much larger volume. A description of the different discharge regimes and a parametric study of the EHD force as a function of voltage rise time and dielectric thickness is presented.

  2. Atmospheric plasma processes for environmental applications

    OpenAIRE

    Shapoval, Volodymyr

    2012-01-01

    Plasma chemistry is a rapidly growing field which covers applications ranging from technological processing of materials, including biological tissues, to environmental remediation and energy production. The so called atmospheric plasma, produced by electric corona or dielectric barrier discharges in a gas at atmospheric pressure, is particularly attractive for the low costs and ease of operation and maintenance involved. The high concentrations of energetic and chemically active species (e.g...

  3. Atmospheric plasma processes for environmental applications

    OpenAIRE

    Shapoval, Volodymyr

    2012-01-01

    Plasma chemistry is a rapidly growing field which covers applications ranging from technological processing of materials, including biological tissues, to environmental remediation and energy production. The so called atmospheric plasma, produced by electric corona or dielectric barrier discharges in a gas at atmospheric pressure, is particularly attractive for the low costs and ease of operation and maintenance involved. The high concentrations of energetic and chemically active species (e.g...

  4. Effect of Electron Energy Distribution on the Hysteresis of Plasma Discharge: Theory, Experiment, and Modeling

    Science.gov (United States)

    Lee, Hyo-Chang; Chung, Chin-Wook

    2016-09-01

    Hysteresis, which is the history dependence of physical systems, indicates that there are more-than-two stable points in a given condition, and it has been considered to one of the most important topics in fundamental physics. Recently, the hysteresis of plasma has become a focus of research because stable plasma operation is very important for fusion reactors, bio-medical plasmas, and industrial plasmas for nano-device fabrication process. Interestingly, the bi-stability characteristics of plasma with a huge hysteresis loop have been observed in inductive discharge plasmas Because hysteresis study in such plasmas can provide a universal understanding of plasma physics, many researchers have attempted experimental and theoretical studies. Despite long plasma research, how this plasma hysteresis occurs remains an unresolved question in plasma physics. Here, we report theory, experiment, and modeling of the hysteresis. It was found experimentally and theoretically that evolution of the electron energy distribution (EED) makes a strong plasma hysteresis. In Ramsauer and non-Ramsauer gas experiments, it was revealed that the plasma hysteresis is observed only at high pressure Ramsauer gas where the EED deviates considerably from a Maxwellian shape. This hysteresis was presented in the plasma balance model where the EED is considered. Because electrons in plasmas are usually not in a thermal equilibrium, this EED-effect can be regarded as a universal phenomenon in plasma physics. This research was partially supported by Korea Research Institute of Standard and Science.

  5. Characteristics of an Atmospheric Discharge Plasma as an RF Antenna

    Science.gov (United States)

    1982-05-27

    continuing PLASMA AS AN RF ANTENNA problem 6. PERFORMIN4G ORO . REPORT NUM99fR 7. AUTNOR(j .C ONTRACT OR GRANT MUMDERp(s) T. Dwyer, J1. R. Greig. D. P. Murphy...path) of the plasma antenna and energy to create and sustain the plasma were supplied directly in the form of an electric discharge a totally new balance...the ground plane, G. The lead was terminated in a corona ball with a small protrusion sticking out towards the laser-designated path. The end of the

  6. Main reaction process simulation of hydrogen gas discharge in a cold cathode electric vacuum device

    Indian Academy of Sciences (India)

    Jing-Ye Liu; Yuan Gao; Gang Wang

    2012-07-01

    Based on the related theory of plasma discharge process and the COMSOL multiphysics software, and considering the corresponding boundary conditions, the related recation types in the hydrogen plasma discharge were simulated and analysed, and the main reactions of hydrogen discharge in small electric vacuum components at low pressure and weak ionization were confirmed. Among the 21 types of reactions in hydrogen discharge process, 11 of them play importnat roles under low pressure and weak ionization in cold cathode electric vacuum device. The simulated results are consistent with the test result.

  7. Combustion Enhancement Using a Silent Discharge Plasma Reactor

    Science.gov (United States)

    Rosocha, Louis; Platts, David; Coates, Don; Stange, Sy

    2003-10-01

    Electric fields affect flame propagation speed, stability, and combustion chemistry. External electrodes, arc discharges, and plasma jets have been used to combust gas mixtures outside their flammability limits. Experiments with silent electrical discharges (SEDs) and propagating flames have shown that flame propagation velocity is actually decreased (combustion retarded) when an SED is applied directly to the flame region, but velocity is increased (combustion promoted) when applied to the unburned gas mixture upstream of a flame. More recent work has proposed electric arc/microwave-driven plasma-generating fuel nozzles to produce dissociated fuel or ionized fuel for aircraft gas turbine engine combustor mixers. In contrast to prior works, we have used a silent discharge plasma (SDP) reactor to break up large fuel molecules into smaller molecules and create free radicals/active species in a gas stream before the fuel is mixed with an oxidizer and combusted. A cylindrical SDP reactor was used to 'activate' propane before mixing it with air and igniting the combustible gas mixture. With the plasma, the physical appearance of the flame changes and substantial changes in mass spectrometer fragmentation peaks for fuel and combustion products are observed (i.e., combustion is enhanced). Results of changes in the degree of combustion will be discussed in terms of variations in the plasma specific energy.

  8. Coal Liquefaction by Using Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Wang, Qiuying; Wu, Peng; Gu, Fan

    2013-07-01

    An innovative method for coal liquefaction by using dielectric barrier discharge (DBD) plasma in a short reaction time was developed. Using tetralin as the reaction medium, DBD plasma as the energy source, and a reaction time of 10 min at 140°C, up to 10% of coal was converted to liquid material. The results showed the feasibility of coal's liquefaction by DBD plasma under relatively moderate conditions. Simultaneously, it was clarified that the effect of DBD plasma treatment was opposed to the thermal effect of heating. An acid plasma sheath could be formed on the coal powder surface in DBD conditions, liquefied reactions could be carried out in the absence of inorganic acid, and the products were nearly neutral and with low causticity.

  9. Effects of Gas Flow Rate on the Discharge Characteristics of a DC Excited Plasma Jet

    Science.gov (United States)

    Li, Xuechen; Jia, Pengying; Di, Cong; Bao, Wenting; Zhang, Chunyan

    2015-09-01

    A direct current (DC) source excited plasma jet consisting of a hollow needle anode and a plate cathode has been developed to form a diffuse discharge plume in ambient air with flowing argon as the working gas. Using optical and electrical methods, the discharge characteristics are investigated for the diffuse plasma plume. Results indicate that the discharge has a pulse characteristic, under the excitation of a DC voltage. The discharge pulse corresponds to the propagation process of a plasma bullet travelling from the anode to the cathode. It is found that, with an increment of the gas flow rate, both the discharge plume length and the current peak value of the pulsed discharge decrease in the laminar flow mode, reach their minima at about 1.5 L/min, and then slightly increase in the turbulent mode. However, the frequency of the pulsed discharge increases in the laminar mode with increasing the argon flow rate until the argon flow rate equals to about 1.5 L/min, and then slightly decreases in the turbulent mode. supported by National Natural Science Foundation of China (Nos. 10805013, 11375051), Funds for Distinguished Young Scientists of Hebei Province, China (No. A2012201045), Department of Education for Outstanding Youth Project of China (No. Y2011120), and Youth Project of Hebei University of China (No. 2011Q14)

  10. A Cascaded Discharge Plasma-Adsorbent Technique for Engine Exhaust Treatment

    Science.gov (United States)

    Rajanikanth, B. S.; Srinivasan, A. D.; Arya, Nandiny B.

    2003-06-01

    A cascaded system of electrical discharges (non-thermal plasma) and adsorption process was investigated for the removal of oxides of Nitrogen (NOx) and total hydrocarbons (THC) from an actual diesel engine exhaust. The non-thermal plasma and adsorption processes were separately studied first and then the cascaded process was studied. In this study, different types of adsorbents were used. The NOx removal efficiency was higher with plasma-associated adsorption (cascaded) process compared to the individual processes and the removal efficiency was found almost invariant in time. When associated by plasma, among the adsorbents studied, activated charcoal and MS-13X were more effective for NOx and THC removal respectively. The experiments were conducted at no load and at 50% load conditions. The plasma reactor was kept at room temperature throughout the experiment, while the temperature of the adsorbent reactor was varied. A relative comparison of adsorbents was discussed at the end.

  11. Structural properties of complex plasmas in a homogeneous dc discharge.

    Science.gov (United States)

    Mitic, S; Klumov, B A; Konopka, U; Thoma, M H; Morfill, G E

    2008-09-19

    We report on the first three-dimensional (3D) complex plasma structure analysis for an experiment that was performed in an elongated discharge tube in the absence of striations. The low frequency discharge was established with 1 kHz alternating dc current through a cylindrical glass tube filled with neon at 30 Pa. The injected particle cloud consisted of monodisperse microparticles. A scanning laser sheet and a camera were used to determine the particle position in 3D. The observed cylindrical-shaped particle cloud showed an ordered structure with a distinct outer particle shell. The observations are in agreement with performed molecular dynamics simulations.

  12. Properties Influencing Plasma Discharges in Packed Bed Reactors

    Science.gov (United States)

    Kruszelnicki, Juliusz; Engeling, Kenneth W.; Foster, John E.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure dielectric barrier discharges (DBDs) sustained in packed bed reactors (PBRs) are being investigated for CO2 removal and conversion of waste gases into higher value compounds. We report on results of a computational investigation of PBR-DBD properties using the plasma hydrodynamics simulator nonPDPSIM with a comparison to experiments. Dielectric beads (rods in 2D) were inserted between two coplanar electrodes, 1 cm apart filled by humid air. A step-pulse of -30 kV was applied to the top electrode. Material properties of the beads (dielectric constant, secondary emission coefficient) and gas properties (photoionization and photo-absorption cross-sections, temperature) were varied. We found that photoionization plays a critical role in the propagation of the discharge through the PBR, as it serves to seed charges in regions of high electric field. Increasing rates of photo-ionization enable increases in the discharge propagation velocity, ionization rates and production of radicals. A transition between DBD-like and arc-like discharges occurs as the radiation mean free path decreases. Increasing the dielectric constant of the beads increased electric fields in the gas, which translated to increased discharge propagation velocity and charge density until ɛ/ɛ0 100. Secondary electron emission coefficient and gas temperature have minimal impacts on the discharge propagation though the latter did affect the production of reactive species. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  13. Gas-discharge sources with charged particle emission from the plasma of glow discharge with a hollow cathode

    CERN Document Server

    Semenov, A P

    2001-01-01

    One studied properties of a magnetron discharge with a cold hollow and uncooled rod cathodes. One demonstrated the dominant effect of thermoelectron emission of a rod cathode heated in a discharge on characteristics of discharge and on emission properties of a gas-discharge plasma and the possibility pf a smooth transition of glow discharge to diffusion mode of arc discharge combustion. Paper describes sources of ions and electrons with improved physical and generalized design and engineering parameters. One shows the promise of the electrode structure of a hollow cathode magnetron discharge to be used as a source, in particular, of the atomic hydrogen and of atom flow of a working rod cathode

  14. Plasma Discharges in Gas Bubbles in Liquid Water: Breakdown Mechanisms and Resultant Chemistry

    Science.gov (United States)

    Gucker, Sarah M. N.

    is created either through flowing gas around the high voltage electrode in the discharge tube or self-generated by the plasma as in the steam discharge. This second method allows for large scale processing of contaminated water and for bulk chemical and optical analysis. Breakdown mechanisms of attached and unattached gas bubbles in liquid water were investigated using the first device. The breakdown scaling relation between breakdown voltage, pressure and dimensions of the discharge was studied. A Paschen-like voltage dependence for air bubbles in liquid water was discovered. The results of high-speed photography suggest the physical charging of the bubble due to a high voltage pulse; this charging can be significant enough to produce rapid kinetic motion of the bubble about the electrode region as the applied electric field changes over a voltage pulse. Physical deformation of the bubble is observed. This charging can also prevent breakdown from occurring, necessitating higher applied voltages to overcome the phenomenon. This dissertation also examines the resulting chemistry from plasma interacting with the bubble-liquid system. Through the use of optical emission spectroscopy, plasma parameters such as electron density, gas temperature, and molecular species production and intensity are found to have a time-dependence over the ac voltage cycle. This dependence is also source gas type dependent. These dependencies afford effective control over plasma-driven decomposition. The effect of plasma-produced radicals on various wastewater simulants is studied. Various organic dyes, halogenated compounds, and algae water are decomposed and assessed. Toxicology studies with melanoma cells exposed to plasma-treated dye solutions are completed, demonstrating the non-cytotoxic quality of the decomposition process. Thirdly, this dissertation examines the steam plasma system, developed through this research to circumvent the acidification associated with gas-feed discharges

  15. Dielectric barrier discharge plasma pretreatment on hydrolysis of microcrystalline cellulose

    Science.gov (United States)

    Fangmin, HUANG; Zhouyang, LONG; Sa, LIU; Zhenglong, Qin

    2017-04-01

    Dielectric barrier discharge (DBD) plasma was used as a pretreatment method for downstream hydrolysis of microcrystalline cellulose (MCC). The degree of polymerization (DP) of MCC decreased after it was pretreated by DBD plasma under a carrier gas of air/argon. The effectiveness of depolymerization was found to be influenced by the crystallinity of MCC when under the pretreatment of DBD plasma. With the addition of tert-butyl alcohol in the treated MCC water suspension solution, depolymerization effectiveness of MCC was inhibited. When MCC was pretreated by DBD plasma for 30 min, the total reducing sugar concentration (TRSC) and liquefaction yield (LY) of pretreated-MCC (PMCC) increased by 82.98% and 34.18% respectively compared with those for raw MCC.

  16. Simulation Tool for Dielectric Barrier Discharge Plasma Actuators

    Science.gov (United States)

    Likhanskii, Alexander

    2014-01-01

    Traditional approaches for active flow separation control using dielectric barrier discharge (DBD) plasma actuators are limited to relatively low speed flows and atmospheric conditions. This results in low feasibility of the DBDs for aerospace applications. For active flow control at turbine blades, fixed wings, and rotary wings and on hypersonic vehicles, DBD plasma actuators must perform at a wide range of conditions, including rarified flows and combustion mixtures. An efficient, comprehensive, physically based DBD simulation tool can optimize DBD plasma actuators for different operation conditions. Researchers are developing a DBD plasma actuator simulation tool for a wide range of ambient gas pressures. The tool will treat DBD using either kinetic, fluid, or hybrid models, depending on the DBD operational condition.

  17. Dielectric barrier discharge plasma pretreatment on hydrolysis of microcrystalline cellulose

    Science.gov (United States)

    Huang, Fangmin; Long, Zhouyang; Liu, Sa; Qin, Zhenglong

    2017-04-01

    Dielectric barrier discharge (DBD) plasma was used as a pretreatment method for downstream hydrolysis of microcrystalline cellulose (MCC). The degree of polymerization (DP) of MCC decreased after it was pretreated by DBD plasma under a carrier gas of air/argon. The effectiveness of depolymerization was found to be influenced by the crystallinity of MCC when under the pretreatment of DBD plasma. With the addition of tert-butyl alcohol in the treated MCC water suspension solution, depolymerization effectiveness of MCC was inhibited. When MCC was pretreated by DBD plasma for 30 min, the total reducing sugar concentration (TRSC) and liquefaction yield (LY) of pretreated-MCC (PMCC) increased by 82.98% and 34.18% respectively compared with those for raw MCC.

  18. Advanced plasma diagnostics for plasma processing

    Science.gov (United States)

    Malyshev, Mikhail Victorovich

    1999-10-01

    A new, non-intrusive, non-perturbing diagnostic method was developed that can be broadly applied to low pressure, weakly ionized plasmas and glow discharges-trace rare gases optical emission spectroscopy (TRG-OES). The method is based on a comparison of intensities of atomic emission from trace amounts of inert gases (He, Ne, Ar, Kr, and Xe) that are added to the discharge to intensities calculated from the theoretical model. The model assumes a Maxwellian electron energy distribution function (EEDF), computes the population of emitting levels both from the ground state and the metastable states of rare gases, and from the best fit between theory and experiment determines electron temperature (Te). Subject to conditions, TRG-OES can also yield electron density or its upper or lower limit. From the comparison of the emission from levels excited predominantly by high energy electrons to that excited by low energy electrons, information about the EEDF can be obtained. The use of TRG-OES also allows a traditionally qualitative actinometry technique (determination of concentration of radical species in plasma through optical emission) to become a precise quantitative method by including Te and rare gases metastables effects. A combination of TRG-OES, advanced actinometry, and Langmuir probe measurements was applied to several different plasma reactors and regimes of operation. Te measurements and experiments to correct excitation cross section were conducted in a laboratory helical resonator. Two chamber configuration of a commercial (Lam Research) metal etcher were studied to determine the effects of plasma parameters on plasma-induced damage. Two different methods (RF inductive coupling and ultra-high frequency coupling) for generating a plasma in a prototype reactor were also studied. Pulsed plasmas, a potential candidate to eliminate the plasma-induced damage to microelectronics devices that occurs in manufacturing due to differential charging of the wafer, have

  19. Delay time for the onset of beam plasma discharge

    Science.gov (United States)

    Parish, J. L.; Denig, W. F.; Raitt, W. J.

    1987-01-01

    The interaction of a nonrelativistic electron beam with a neutral gas in a large chamber is considered, and the time interval before ignition of beam plasma discharge (BPD) is studied. A new theoretical expression for the time delay before BPD ignition is found as a function of the critical current necessary for BPD to be established. There are two parameters in the theoretical expression, and both are derived from two different experiments. These parameters are used to write the time evolution equation for plasma density as a function of time.

  20. Discharge processes of UV pre-ionized electric-discharge pulsed DF laser

    Science.gov (United States)

    Pan, Qikun; Xie, Jijiang; Shao, Chunlei; Wang, Chunrui; Shao, Mingzhen; Guo, Jin

    2016-03-01

    The discharge processes of ultraviolet (UV) pre-ionized electric-discharge pulsed DF laser operating with a SF6-D2 gas mixture are studied. A mathematical model based on continuity equation of electrons and Kirchhoff equations for discharge circuit is established to describe the discharge processes. Voltage and current waveforms of main discharge and voltage waveforms of pre-ionization are solved numerically utilizing the model. The calculations correctly display some physical processes, such as the delay time between pre-ionization and main discharge, breakdown of the main electrode and self-sustained volume discharge (SSVD). The results of theory are consistent with the experiments, which are performed in our non-chain pulsed DF laser. Then the delay inductance and peak capacitance are researched to analyze their influences on discharge processes, and the circuit parameters of DF laser are given which is useful to improve the discharge stability.

  1. Evaluation and Optimization of Electrode Configuration of Multi-Channel Corona Discharge Plasma for Dye-Containing Wastewater Treatment

    Science.gov (United States)

    Ren, Jingyu; Wang, Tiecheng; Qu, Guangzhou; Liang, Dongli; Hu, Shibin

    2015-12-01

    A discharge plasma reactor with a point-to-plane structure was widely studied experimentally in wastewater treatment. In order to improve the utilization efficiency of active species and the energy efficiency of this kind of discharge plasma reactor during wastewater treatment, the electrode configuration of the point-to-plane corona discharge reactor was studied by evaluating the effects of discharge spacing and adjacent point distance on discharge power and discharge energy density, and then dye-containing wastewater decoloration experiments were conducted on the basis of the optimum electrode configuration. The experimental results of the discharge characteristics showed that high discharge power and discharge energy density were achieved when the ratio of discharge spacing to adjacent point distance (d/s) was 0.5. Reactive Brilliant Blue (RBB) wastewater treatment experiments presented that the highest RBB decoloration efficiency was observed at d/s of 0.5, which was consistent with the result obtained in the discharge characteristics experiments. In addition, the biodegradability of RBB wastewater was enhanced greatly after discharge plasma treatment under the optimum electrode configuration. RBB degradation processes were analyzed by GC-MS and IC, and the possible mechanism for RBB decoloration was also discussed. supported by China's Postdoctoral Science Foundation (No. 2014M562460), the Initiative Funding Programs for Doctoral Research of Northwest A&F University (No. 2013BSJJ121), and National Natural Science Foundation of China (No. 21107085)

  2. Cold-cathode, pulsed-power plasma discharge switch

    Science.gov (United States)

    Goebel, Dan M.

    1996-09-01

    CROSSATRONTMmodulator switches are cold-cathode, grid-controlled, plasma-discharge devices that are used for thyratron and hard-tube replacement in high-voltage, pulsed-power applications. CROSSATRON modulator switches have been used to produce square pulses of up to 100 kV and 1000 A, and CROSSATRON laser-discharge switches have switched peak discharge currents of up to 10 kA at 40 kV. The major advantage that CROSSATRON switches offer over other plasma switches is a rapid deionization time that permits high pulse-repetition frequencies (103 to 106 pulses per second depending on the application), and a long life associated with the cold-cathode plasma production mechanism. Compared to hard tubes, CROSSATRON switches have a relatively low forward voltage drop (500 V), the ability to close and open up to 1 kA of peak current, and lower grid-drive power requirements. In this article, we describe the physical mechanisms for how the switch works based on simple models and experimental data. The design of CROSSATRON switches is explained, and characteristic performance in closing and opening applications is described and explained.

  3. Design of a Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley K.; Polzin, Kurt A.

    2010-01-01

    The design and construction of a thruster that employs electrodeless plasma preionization and pulsed inductive acceleration is described. Preionization is achieved through an electron cyclotron resonance discharge that produces a weakly-ionized plasma at the face of a conical theta pinch-shaped inductive coil. The presence of the preionized plasma allows for current sheet formation at lower discharge voltages than those employed in other pulsed inductive accelerators that do not employ preionization. The location of the electron cyclotron resonance discharge is controlled through the design of the applied magnetic field in the thruster. Finite element analysis shows that there is an arrangement of permanent magnets that yields a small volume of resonant magnetic field at the coil face. Preionization in the resonant zone leads to current sheet formation at the coil face, which minimizes the initial inductance of the pulse circuit and maximizes the potential electrical efficiency of the accelerator. A magnet assembly was constructed around an inductive coil to provide structural support to the selected arrangement of neodymium magnets. Measured values of the resulting magnetic field compare favorably with the finite element model.

  4. Carbon dioxide splitting in a dielectric barrier discharge plasma: a combined experimental and computational study.

    Science.gov (United States)

    Aerts, Robby; Somers, Wesley; Bogaerts, Annemie

    2015-02-01

    Plasma technology is gaining increasing interest for the splitting of CO2 into CO and O2 . We have performed experiments to study this process in a dielectric barrier discharge (DBD) plasma with a wide range of parameters. The frequency and dielectric material did not affect the CO2 conversion and energy efficiency, but the discharge gap can have a considerable effect. The specific energy input has the most important effect on the CO2 conversion and energy efficiency. We have also presented a plasma chemistry model for CO2 splitting, which shows reasonable agreement with the experimental conversion and energy efficiency. This model is used to elucidate the critical reactions that are mostly responsible for the CO2 conversion. Finally, we have compared our results with other CO2 splitting techniques and we identified the limitations as well as the benefits and future possibilities in terms of modifications of DBD plasmas for greenhouse gas conversion in general.

  5. A Cascaded Discharge Plasma-Adsorbent Technique for Engine Exhaust Treatment

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A cascaded system of electrical discharges (non-thermal plasma) and adsorptionprocess was investigated for the removal of oxides of Nitrogen (NOx) and total hydrocarbons(THC) from an actual diesel engine exhaust. The non-thermal plasma and adsorption processeswere separately studied first and then the cascaded process was studied. In this study, differenttypes of adsorbents were used. The NOx removal efficiency was higher with plasma-associatedadsorption (cascaded) process compared to the individual processes and the removal efficiencywas found almost invariant in time. When associated by plasma, among the adsorbents studied,activated charcoal and MS-13X were more effective for NOx and THC removal respectively. Theexperiments were conducted at no load and at 50 % load conditions. The plasma reactor was keptat room temperature throughout the experiment, while the temperature of the adsorbent reactorwas varied. A relative comparison of adsorbents was discussed at the end.

  6. Formation and Dynamics of Vortex Structures in Pure and Gas-Discharge Nonneutral Collisionless Electron Plasmas

    CERN Document Server

    Kervalishvili, N A

    2013-01-01

    The comparative analysis of the results of experimental investigations of the processes of formation, interaction and dynamics of vortex structures in pure electron and gas-discharge electron nonneutral plasmas taking place for the period of time much less than the electron-neutral collision time has been given. The general processes of formation and behavior of vortex structures in these two plasmas were considered. The phenomena, taking place only in one of these plasmas were also considered. It is shown that the existing difference in behavior of vortex structures is caused by different initial states of nonneutral electron plasmas. The role of vortex structures in the processes taking place in nonneutral electron plasma is discussed.

  7. STUDY OF DESTRUCTION PROCESSES OF SYNTHETIC SURFACE-ACTIVE SUBSTENCES (SURFFACTANTS IN BARRIER DISCHARGE

    Directory of Open Access Journals (Sweden)

    V.I. Grinevich

    2012-06-01

    Full Text Available Kinetic data of degradation on aqueous solutions of surfactants in the plasma of barrier discharge are presented. The possible mechanism of proceeding processes is offered and considered. It is shown that the treatment in a barrier discharge results in decomposition efficiency of 95%. It is established that the main product of degradation are carboxylic acids.

  8. Dielectric barrier discharge plasma actuator for flow control

    Science.gov (United States)

    Opaits, Dmitry Florievich

    Electrohydrodynamic (EHD) and magnetohydrodynamic phenomena are being widely studied for aerodynamic applications. The major effects of these phenomena are heating of the gas, body force generation, and enthalpy addition or extraction, [1, 2, 3]. In particular, asymmetric dielectric barrier discharge (DBD) plasma actuators are known to be effective EHD device in aerodynamic control, [4, 5]. Experiments have demonstrated their effectiveness in separation control, acoustic noise reduction, and other aeronautic applications. In contrast to conventional DBD actuators driven by sinusoidal voltages, we proposed and used a voltage profile consisting of nanosecond pulses superimposed on dc bias voltage. This produces what is essentially a non-self-sustained discharge: the plasma is generated by repetitive short pulses, and the pushing of the gas occurs primarily due to the bias voltage. The advantage of this non-self-sustained discharge is that the parameters of ionizing pulses and the driving bias voltage can be varied independently, which adds flexibility to control and optimization of the actuators performance. Experimental studies were conducted of a flow induced in a quiescent room air by a single DBD actuator. A new approach for non-intrusive diagnostics of plasma actuator induced flows in quiescent gas was proposed, consisting of three elements coupled together: the Schlieren technique, burst mode of plasma actuator operation, and 2-D numerical fluid modeling. During the experiments, it was found that DBD performance is severely limited by surface charge accumulation on the dielectric. Several ways to mitigate the surface charge were found: using a reversing DC bias potential, three-electrode configuration, slightly conductive dielectrics, and semi conductive coatings. Force balance measurements proved the effectiveness of the suggested configurations and advantages of the new voltage profile (pulses+bias) over the traditional sinusoidal one at relatively low

  9. Self-consistent evolution of plasma discharge and electromagnetic fields in a microwave pulse compressor

    Energy Technology Data Exchange (ETDEWEB)

    Shlapakovski, A. S.; Beilin, L.; Krasik, Ya. E. [Physics Department, Technion 32000 Haifa (Israel); Hadas, Y. [Department of Applied Physics, Rafael, POBox 2250, Haifa 31021 (Israel); Schamiloglu, E. [Department of Electrical and Computer Engineering, University of New Mexico, Albuquerque, New Mexico 87131 (United States)

    2015-07-15

    Nanosecond-scale evolution of plasma and RF electromagnetic fields during the release of energy from a microwave pulse compressor with a plasma interference switch was investigated numerically using the code MAGIC. The plasma was simulated in the scope of the gas conductivity model in MAGIC. The compressor embodied an S-band cavity and H-plane waveguide tee with a shorted side arm filled with pressurized gas. In a simplified approach, the gas discharge was initiated by setting an external ionization rate in a layer crossing the side arm waveguide in the location of the electric field antinode. It was found that with increasing ionization rate, the microwave energy absorbed by the plasma in the first few nanoseconds increases, but the absorption for the whole duration of energy release, on the contrary, decreases. In a hybrid approach modeling laser ignition of the discharge, seed electrons were set around the electric field antinode. In this case, the plasma extends along the field forming a filament and the plasma density increases up to the level at which the electric field within the plasma decreases due to the skin effect. Then, the avalanche rate decreases but the density still rises until the microwave energy release begins and the electric field becomes insufficient to support the avalanche process. The extraction of the microwave pulse limits its own power by terminating the rise of the plasma density and filament length. For efficient extraction, a sufficiently long filament of dense plasma must have sufficient time to be formed.

  10. Self-consistent evolution of plasma discharge and electromagnetic fields in a microwave pulse compressor

    Science.gov (United States)

    Shlapakovski, A. S.; Beilin, L.; Hadas, Y.; Schamiloglu, E.; Krasik, Ya. E.

    2015-07-01

    Nanosecond-scale evolution of plasma and RF electromagnetic fields during the release of energy from a microwave pulse compressor with a plasma interference switch was investigated numerically using the code MAGIC. The plasma was simulated in the scope of the gas conductivity model in MAGIC. The compressor embodied an S-band cavity and H-plane waveguide tee with a shorted side arm filled with pressurized gas. In a simplified approach, the gas discharge was initiated by setting an external ionization rate in a layer crossing the side arm waveguide in the location of the electric field antinode. It was found that with increasing ionization rate, the microwave energy absorbed by the plasma in the first few nanoseconds increases, but the absorption for the whole duration of energy release, on the contrary, decreases. In a hybrid approach modeling laser ignition of the discharge, seed electrons were set around the electric field antinode. In this case, the plasma extends along the field forming a filament and the plasma density increases up to the level at which the electric field within the plasma decreases due to the skin effect. Then, the avalanche rate decreases but the density still rises until the microwave energy release begins and the electric field becomes insufficient to support the avalanche process. The extraction of the microwave pulse limits its own power by terminating the rise of the plasma density and filament length. For efficient extraction, a sufficiently long filament of dense plasma must have sufficient time to be formed.

  11. INTRODUCTION: Nonequilibrium Processes in Plasmas

    Science.gov (United States)

    Petrović, Zoran; Marić, Dragana; Malović, Gordana

    2009-07-01

    This book aims to give a cross section from a wide range of phenomena that, to different degrees, fall under the heading of non-equilibrium phenomenology. The selection is, of course, biased by the interests of the members of the scientific committee and of the FP6 Project 026328 IPB-CNP Reinforcing Experimental Centre for Non-equilibrium Studies with Application in Nano-technologies, Etching of Integrated Circuits and Environmental Research. Some of the papers included here are texts based on selected lectures presented at the Second International Workshop on Non-equilibrium Processes in Plasmas and Environmental Science. However, this volume is not just the proceedings of that conference as it contains a number of papers from authors that did not attend the conference. The goal was to put together a volume that would cover the interests of the project and support further work. It is published in the Institute of Physics journal Journal of Physics: Conference Series to ensure a wide accessibility of the articles. The texts presented here range from in-depth reviews of the current status and past achievements to progress reports of currently developed experimental devices and recently obtained still unpublished results. All papers have been refereed twice, first when speakers were selected based on their reputation and recently published results, and second after the paper was submitted both by the editorial board and individual assigned referees according to the standards of the conference and of the journal. Nevertheless, we still leave the responsibility (and honours) for the contents of the papers to the authors. The papers in this book are review articles that give a summary of the already published work or present the work in progress that will be published in full at a later date (or both). In the introduction to the first volume, in order to show how far reaching, ubiquitous and important non-equilibrium phenomena are, we claimed that ever since the early

  12. Volume Diffuse Dielectric Barrier Discharge Plasma Produced by Nanosecond High Voltage Pulse in Airflow

    Institute of Scientific and Technical Information of China (English)

    QI Haicheng; GAO Wei; FAN Zhihui; LIU Yidi; REN Chunsheng

    2016-01-01

    Volume diffuse dielectric barrier discharge (DBD) plasma is produced in subsonic airflow by nanosecond high-voltage pulse power supply with a plate-to-plate discharge cell at 6 mm air gap length.The discharge images,optical emission spectra (OES),the applied voltage and current waveforms of the discharge at the changed airflow rates are obtained.When airflow rate is increased,the transition of the discharge mode and the variations of discharge intensity,breakdown characteristics and the temperature of the discharge plasma are investigated.The results show that the discharge becomes more diffuse,discharge intensity is decreased accompanied by the increased breakdown voltage and time lag,and the temperature of the discharge plasma reduces when airflow of small vclocity is introduced into the discharge gap.These phenomena are because that the airflow changes the spatial distribution of the heat and the space charge in the discharge gap.

  13. Volume Diffuse Dielectric Barrier Discharge Plasma Produced by Nanosecond High Voltage Pulse in Airflow

    Science.gov (United States)

    Qi, Haicheng; Gao, Wei; Fan, Zhihui; Liu, Yidi; Ren, Chunsheng

    2016-05-01

    Volume diffuse dielectric barrier discharge (DBD) plasma is produced in subsonic airflow by nanosecond high-voltage pulse power supply with a plate-to-plate discharge cell at 6 mm air gap length. The discharge images, optical emission spectra (OES), the applied voltage and current waveforms of the discharge at the changed airflow rates are obtained. When airflow rate is increased, the transition of the discharge mode and the variations of discharge intensity, breakdown characteristics and the temperature of the discharge plasma are investigated. The results show that the discharge becomes more diffuse, discharge intensity is decreased accompanied by the increased breakdown voltage and time lag, and the temperature of the discharge plasma reduces when airflow of small velocity is introduced into the discharge gap. These phenomena are because that the airflow changes the spatial distribution of the heat and the space charge in the discharge gap. supported by National Natural Science Foundation of China (No. 51437002)

  14. Focusing of plasma flow in an E cross B discharge

    Science.gov (United States)

    Griswold, Martin; Raitses, Yevgeny; Fisch, Nathaniel J.

    2010-11-01

    ExB discharges can be used to accelerate ions in a quasi-neutral plasma. Large ion fluxes can be produced in this way because there is no space charge limitation, however difficulty in specifying the electric field distribution results in large flow divergence [1]. Recent work has identified new methods to control the flow divergence [2,3]. We present the results of new techniques that are designed to further reduce the divergence. [4pt] [1] A.I. Morozov and V.V. Savelyev, Reviews of Plasma Physics vol. 21, B. B. Kadomtsev and V. D. Shafranov, Eds. New York: Consultants Bureau, 2000. [2] Y. Raitses, L.A. Dorf, A.A. Litvak, and N.J. Fisch, Journal of Applied Physics 88 (2000) 1263. [3] A. Smirnov, Y. Raitses, and N.J. Fisch, IEEE Transactions on Plasma Science 36 (2008) 1998.

  15. Three-dimensional discharge simulation of inductively coupled plasma (ICP) etching reactor

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    More and more importance has been attached to inductively coupled plasma (ICP) in semiconductor manufacture. For a deep understanding of the plasma discharge process in the etching reactor, this study made a three-dimensional simulation on the Ar plasma discharge process with the commercial software CFD-ACE, which is according to the real experiment conditions and data supplied by North Microelec-tronic Corporation. The error of the simulation results is in the range of ±20% with credibility. The numerical results show that the three-dimentional spatial distribu-tion of electron density is reduced from the chamber center to the wall. The distri-bution of electron density, electron temperature and power deposition is related to the shape and placement of the coil.

  16. Genetic effects of an air discharge plasma on Staphylococcus aureus at the gene transcription level

    Science.gov (United States)

    Xu, Zimu; Wei, Jun; Shen, Jie; Liu, Yuan; Ma, Ronghua; Zhang, Zelong; Qian, Shulou; Ma, Jie; Lan, Yan; Zhang, Hao; Zhao, Ying; Xia, Weidong; Sun, Qiang; Cheng, Cheng; Chu, Paul K.

    2015-05-01

    The dynamics of gene expression regulation (at transcription level) in Staphylococcus aureus after different doses of atmospheric-pressure room-temperature air plasma treatments are investigated by monitoring the quantitative real-time polymerase chain reaction. The plasma treatment influences the transcription of genes which are associated with several important bio-molecular processes related to the environmental stress resistance of the bacteria, including oxidative stress response, biofilm formation, antibiotics resistance, and DNA damage protection/repair. The reactive species generated by the plasma discharge in the gas phase and/or induced in the liquid phase may account for these gene expression changes.

  17. ROS/RNS Production in Water Using Various Discharge Plasma

    Science.gov (United States)

    Takahashi, Kazuhiro; Satoh, Kohki; Itoh, Hidenori; Kawaguchi, Hideki; Timoshkin, Igor; Given, Martin; MacGregor, Scott

    2015-09-01

    A pulsed discharge, a DC corona discharge and an atmospheric pressure plasma jet are generated above water, the off-gas of a packed-bed dielectric barrier discharge (PB-DBD) is sparged into water, and then reactive oxygen species and reactive nitrogen species in the water are investigated. H2O2, NO3- and a trace of NO2- are produced in the water after the plasma exposure. H2O2 concentration decreases when NO3- concentration increases, so that this is likely that OH radical to produce H2O2 by OH + OH -->H2O2 is consumed in the NO3- production by NO2 + OH --> HNO3 --> NO3-+ H+ (in water). Since no species is detected in water by the sparging of the PB-DBD off-gas containing more than 1000 ppm of O3, O3 does not contribute to produce H2O2 in water. Further, only NO3- is produced by the sparging of the off-gas containing N2O5 and HNO3. This leads that H2O2 and NO2- can be produced by short-lifetime species in plasma. In this work, the highest generation efficiency of H2O2 and NO2- are respectively 3,820 μg/Wh and 830 μg/Wh by the pulsed-plasma exposure, and that of NO3- is 2,530 μg/Wh by the off-gas sparging of the PB-DBD.

  18. Simulation of plasma discharge in liquids: A detailed two-phase fluid approach

    Science.gov (United States)

    Charchi Aghdam, Ali; Farouk, Tanvir; Reacting Systems; Advanced Energy Research Laboratory Team

    2015-09-01

    Plasma discharge in liquids has gained great attention recently due to its applications in biomedical engineering, fuel processing, and water treatment and so on. Despite the tremendous interest, a comprehensive understanding of the underlying physics still remains limited. In the current work, an attempt is made to present a mathematical multi-physics model to describe the discharge of plasma in liquids. An in-house modeling platform is developed for simulating plasma formation in multiphase fluids. The model resolves a detailed two-phase fluid including viscous effects, surface tension, gravitational forces and electrical body force. All the governing equations are solved for gas and liquid phases. Electric field and charged species equations along with the plasma reaction kinetics are solved to get the charge distribution in the different phases as well as at the gas-liquid interface to obtain the electric body force acting at the interface. By coupling the above sub-models, a comprehensive multi-physics model for plasma discharge in liquids is constructed which is able to capture several physical aspects of the phenomena especially the role of the bubble, its motion and distortion on plasma characteristics.

  19. Potential Industrial Applications of the One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) Operating in Ambient Air

    Science.gov (United States)

    Reece Roth, J.

    2004-11-01

    The majority of industrial plasma processing with glow discharges has been conducted at pressures below 10 torr. This tends to limit applications to high value workpieces as a result of the high capital cost of vacuum systems and the production constraints of batch processing. It has long been recognized that glow discharge plasmas would play a much larger industrial role if they could be generated at one atmosphere. The One Atmosphere Uniform Glow Discharge Plasma (OAUGDP), developed at the University of Tennessee's Plasma Sciences Laboratory, is a non-thermal RF plasma operating on displacement currents with the time-resolved characteristics of a classical low pressure DC normal glow discharge. As a glow discharge, the OAUGDP operates with maximum electrical efficiency at the Stoletow point, where the energy input per ion-electron pair is a minimum [1, 2]. Several interdisciplinary teams have investigated potential applications of the OAUGDP. These teams included collaborators from the UTK Textiles and Nonwovens Development Center (TANDEC), and the Departments of Electrical and Computer Engineering, Microbiology, and Food Science and Technology, as well as the NASA Langley Research Center. The potential applications of the OAUGDP have all been at one atmosphere and room temperature, using air as the working gas. These applications include sterilizing medical and dental equipment; sterilizable air filters to deal with the "sick building syndrome"; removal of soot from Diesel engine exhaust; subsonic plasma aerodynamic effects, including flow re-attachment to airfoils and boundary layer modification; electrohydrodynamic (EDH) flow control of working gases; increasing the surface energy of materials; improving the adhesion of paints and electroplated layers: improving the wettability and wickability of fabrics; stripping of photoresist; and plasma deposition and directional etching of potential microelectronic relevance. [1] J. R. Roth, Industrial Plasma Engineering

  20. Atmospheric pressure plasmas for aerosols processes in materials and environment

    Science.gov (United States)

    Borra, J. P.; Jidenko, N.; Bourgeois, E.

    2009-08-01

    The paper highlights applications of some atmospheric pressure plasmas (dc-corona, streamer and spark and ac-Dielectric Barrier Discharges) to aerosol processes for Materials and Environment (filtration, diagnostics). The production of vapor i.e. condensable gaseous species, leads to nano-sized particles by physical and chemical routes of nucleation in these AP plasmas: (i) when dc streamer and spark filamentary discharges as well as ac filamentary dielectric barrier discharges interact with metal or dielectric surfaces, and (ii) when discharges induce reactions with gaseous precursors in volume. It is shown how composition, size and structure of primary nano-particles are related to plasma parameters (energy, number per unit surface and time and thermal gradients). Then the growth by coagulation controls the final size of agglomerates versus plasma parameters and transit time in and after the plasma. Charging and electro-thermal collection are depicted to account for the related potential applications of controlled kinematics of charged aerosol.

  1. PREFACE: 12th International Conference on Gas Discharge Plasmas and Their Applications

    Science.gov (United States)

    Koval, N.; Landl, N.; Bogdan, A.; Yudin, A.

    2015-11-01

    The 12th International Conference ''Gas Discharge Plasmas and Their Applications'' (GDP 2015) was held in Tomsk, Russia, on September 6-11, 2015. GDP 2015 represents a continuation of the conferences on physics of gas discharge held in Russia since 1984 and seminars and conferences on the technological applications of low temperature plasmas traditionally organized in Tomsk. The six-day Conference brought together the specialists from different countries and organizations and provided an excellent opportunity to exchange knowledge, make oral contributions and poster presentations, and initiate discussions on the topics that are of interest to the Conference participants. The selected papers of the Conference cover a wide range of technical areas and modern aspects of the physical processes in the generators of low-temperature plasma, the low and high-pressure discharges, the pulsed plasma sources, the surface modification, and other gas-discharge technologies. The Conference was hosted by Institute of High Current Electronics SB RAS, Tomsk Polytechnic University, Tomsk Scientific Center, and Tomsk State University of Architecture and Building.

  2. Thrust Stand Measurements of the Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley K.; Polzin, Kurt A.; Emsellem, Gregory D.

    2011-01-01

    Pulsed inductive plasma thrusters [1-3] are spacecraft propulsion devices in which electrical energy is capacitively stored and then discharged through an inductive coil. This type of pulsed thruster is electrodeless, with a time-varying current in the coil interacting with a plasma covering the face of the coil to induce a plasma current. Propellant is accelerated and expelled at a high exhaust velocity (O(10-100 km/s)) by the Lorentz body force arising from the interaction of the magnetic field and the induced plasma current. While this class of thruster mitigates the life-limiting issues associated with electrode erosion, pulsed inductive plasma thrusters require high pulse energies to inductively ionize propellant. The Microwave Assisted Dis- charge Inductive Plasma Accelerator (MAD-IPA), shown in Fig. 1, is a pulsed inductive plasma thruster that addressees this issue by partially ionizing propellant inside a conical inductive coil before the main current pulse via an electron cyclotron resonance (ECR) discharge. The ECR plasma is produced using microwaves and a static magnetic field from a set of permanent magnets arranged to create a thin resonance region along the inner surface of the coil, restricting plasma formation, and in turn current sheet formation, to a region where the magnetic coupling between the plasma and the theta-pinch coil is high. The use of a conical theta-pinch coil also serves to provide neutral propellant containment and plasma plume focusing that is improved relative to the more common planar geometry of the Pulsed Inductive Thruster (PIT) [1, 2]. In this paper, we describe thrust stand measurements performed to characterize the performance (specific impulse, thrust efficiency) of the MAD-IPA thruster. Impulse data are obtained at various pulse energies, mass flow rates and inductive coil geometries. Dependencies on these experimental parameters are discussed in the context of the current sheet formation and electromagnetic plasma

  3. Electrical discharges of plasma ozonizer and its application

    Directory of Open Access Journals (Sweden)

    Tirawanichakul, S.

    2007-05-01

    Full Text Available Ozone synthesis is one of the applications of near atmospheric plasma processing. An ozone generator in this research comprised two annular cylindrical-shaped electrodes. The inner electrode was made ofstainless steel covered with the dielectric glass and the outer electrode was also made of stainless steel. The electric spacing gap was 0.0075 m and length of ozonizer was 0.21 m. Oxygen gas passing through thedischarge gap between two electrodes supplied by an alternating current (AC high voltage power supply, frequency 50 Hz, ranging of 6-10 kVAC was used for producing ozone. The amount of ozone was determinedby the KI standard method. The result showed that the concentration of ozone is proportional to the AC applied voltage. For determining effect of purified oxygen feed rate of 6-10 L/min on quantity of ozone, theresults indicated that at the volumetric flow rate of 8 L/min produced the largest amount of ozone. In addition, ozone concentration at a flow rate of 8 L/min and an electrical discharge time of 3 minutes wasapproximately determined as 41, 60, 80 and 135 mg/L at 8, 9, 10 and 11 kVAC, respectively. Moreover, study of dye wastewater of Krajud mat was proposed and treated by three different methods. Firstly, dye wastewater was solely treated by a plasma ozonation. Secondly, a combination ofozonation and alum coagulation was used for dye wastewater treatment. Finally, the combined ozonation and activated carbon adsorption were used for dye wastewater treatment. The experimental results showedthat the percentage of light absorbance reduction of pink dyed wastewater for these three different methods was about 56%, 35% and 10%, respectively compared to the reference sample. In addition, For thesemethods, the percentage of BOD of treated dye wastewater could be reduced to 64%, 54% and 46% respectively, the percentage of COD could be reduced to approximately 78%, 62% and 27%, respectively, comparedto the reference sample. In conclusion, the

  4. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Jiajian; Gao, Jinlong; Ehn, Andreas; Aldén, Marcus; Li, Zhongshan, E-mail: zhongshan.li@forbrf.lth.se, E-mail: alpers@ma.tum.de [Division of Combustion Physics, Lund University, P.O. Box 118, S-221 00 Lund (Sweden); Moseev, Dmitry [Max-Planck-Institut für Plasmaphysik, D-85748 Garching bei München (Germany); FOM Institute DIFFER, 3430 BE Nieuwegein (Netherlands); Kusano, Yukihiro [Department of Wind Energy, Section for Composites and Materials Mechanics, Technical University of Denmark, Risø Campus, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Salewski, Mirko [Department of Physics, Section for Plasma Physics and Fusion Energy, Technical University of Denmark, DK-2800 Kongens Lyngby (Denmark); Alpers, Andreas, E-mail: zhongshan.li@forbrf.lth.se, E-mail: alpers@ma.tum.de; Gritzmann, Peter; Schwenk, Martin [Zentrum Mathematik, Technische Universität München, D-85747 Garching bei München (Germany)

    2015-01-26

    A non-thermal gliding arc discharge was generated at atmospheric pressure in an air flow. The dynamics of the plasma column and tracer particles were recorded using two synchronized high-speed cameras. Whereas the data analysis for such systems has previously been performed in 2D (analyzing the single camera image), we provide here a 3D data analysis that includes 3D reconstructions of the plasma column and 3D particle tracking velocimetry based on discrete tomography methods. The 3D analysis, in particular, the determination of the 3D slip velocity between the plasma column and the gas flow, gives more realistic insight into the convection cooling process. Additionally, with the determination of the 3D slip velocity and the 3D length of the plasma column, we give more accurate estimates for the drag force, the electric field strength, the power per unit length, and the radius of the conducting zone of the plasma column.

  5. Dielectric Barrier Discharge Plasma Actuator for Flow Control

    Science.gov (United States)

    Opaits, Dmitry, F.

    2012-01-01

    This report is Part II of the final report of NASA Cooperative Agreement contract no. NNX07AC02A. It includes a Ph.D. dissertation. The period of performance was January 1, 2007 to December 31, 2010. Part I of the final report is the overview published as NASA/CR-2012- 217654. Asymmetric dielectric barrier discharge (DBD) plasma actuators driven by nanosecond pulses superimposed on dc bias voltage are studied experimentally. This produces non-self-sustained discharge: the plasma is generated by repetitive short pulses, and the pushing of the gas occurs primarily due to the bias voltage. The parameters of ionizing pulses and the driving bias voltage can be varied independently, which adds flexibility to control and optimization of the actuators performance. The approach consisted of three elements coupled together: the Schlieren technique, burst mode of plasma actuator operation, and 2-D numerical fluid modeling. During the experiments, it was found that DBD performance is severely limited by surface charge accumulation on the dielectric. Several ways to mitigate the surface charge were found: using a reversing DC bias potential, three-electrode configuration, slightly conductive dielectrics, and semi conductive coatings. Force balance measurements proved the effectiveness of the suggested configurations and advantages of the new voltage profile (pulses+bias) over the traditional sinusoidal one at relatively low voltages. In view of practical applications certain questions have been also addressed, such as electrodynamic effects which accompany scaling of the actuators to real size models, and environmental effects of ozone production by the plasma actuators.

  6. Influence of plasma discharge on the structure of polytetrafluoroethylene film and step coverage on polymer substrate

    Energy Technology Data Exchange (ETDEWEB)

    Grytsenko, K.P. [Institute of Semiconductor Physics, 45 Nauki pr., Kyiv, 03028 (Ukraine); Institute of Photonics, Laser and Plasma Technology, University of Applied Sciences Wildau, F.-Engels-Str. 63, 15745, Wildau (Germany)], E-mail: d_gryts@isp.kiev.ua; Lytvyn, P.M. [Institute of Semiconductor Physics, 45 Nauki pr., Kyiv, 03028 (Ukraine); Friedrich, J.; Schulze, R.D. [Federal Institute for Materials Research and Testing (BAM), Unter den Eichen 87, 12205 Berlin (Germany); Schrader, S. [Institute of Photonics, Laser and Plasma Technology, University of Applied Sciences Wildau, F.-Engels-Str. 63, 15745, Wildau (Germany)

    2007-09-15

    Polytetrafluoroethylene (PTFE) films have been deposited onto polycarbonate (PC) substrates from the products of PTFE evaporation, activated by a cloud of accelerated electrons. A 40.68 MHz glow discharge was used during the deposition process. The polymer films have been characterised by XPS, FTIR and AFM. The use of the low power plasma during film growth led to the formation of PTFE films with modified structure. Films are amorphous and contain more cross-links, but in general, the structure of their macromolecules is still linear. An increase of RF-power leads to the formation of films with large amount of double bonds and enhanced internal stresses. Deposition of PTFE on PC without plasma treatment led to the formation of PTFE clusters up to 50 nm in diameter. The RMS roughness of the films, deposited without plasma, was about 4 nm, while the films deposited with plasma treatment had a roughness of 1.5 nm. The use of plasma has an additional effect if a PTFE coating is deposited on the PC substrate with submicrometer-sized steps. Without plasma the steps retain a rectangular shape. Deposited with the RF-discharge the PTFE layers resemble plasma-polymerised films. Under certain conditions the deposited films can fill trenches in the substrate like a wetting liquid, while under other conditions they avoid trenches and grow in between them.

  7. Preparation of carbon nanoparticles by plasma arc discharge under fluidized dynamic equilibrium

    Science.gov (United States)

    Wang, F.; Sun, D. L.; Hong, R. Y.; Kumar, M. R.

    2016-06-01

    Continuous preparation of carbon nanoparticles by dielectric barrier discharge (DBD)-induced non-thermal plasma arc discharge with large spacing in a modified fluidized bed is presented. Discharge arc is generated via the inducement of DBD which provides conductive media in order to realize a large spacing arc discharge. Three kinds of flow conditions defined as full circulation, fluidized dynamic equilibrium, and full collection are determined by the relationship of critical fluidized velocity and the real gas velocity after some modification of the fluidized bed. Movement model of carbon nanoparticles has been proposed to illustrate the flow conditions. A visualized and comprehensive refinement of aggregating processes has been exhibited and proved by high-resolution transmission electron microscopy. Simplified equivalent electrical conductive model of the arc discharge system is successful to generally and perspicuously figure out the discharge process which is impeded by the generated carbon nanoparticles. Effects of flow conditions and flow ratio of carrier gas/carbon source on morphology and yield of nanoparticles have been analyzed by morphology observation and yield calculation along with modeling the process.

  8. IR-LAS Measurements of a Pulsed Xenon Discharge Plasma

    Science.gov (United States)

    Jinno, Masafumi; Wada, Ryota; Motomura, Hideki; Aono, Masaharu

    As a first step to understand the processes taking place in a pulsed xenon discharge, the temporal behavior of the radial metastable atom distribution in a xenon lamp was measured by IR laser absorption spectroscopy. During the first 10μs after starting the discharge, high electron density and the depletion of the ground state atoms at the center of the discharge brought about an almost flat distribution of the metastable atoms within the half-radius area. Following that, the metastable atom density became higher at the center than outside because of recombination between electrons and ions. After the metastable density increase and following voltage cut off, the metastable density decreases again. Considering the diffusion equation alongside these results, it becomes clear that the decrease of the metastable density is caused by quenching to the resonace level from the metastable level or three-body collisions forming excimers.

  9. Magnetohydrodynamic simulation of the inverse-pinch plasma discharge

    Science.gov (United States)

    Esaulov, A.; Bauer, B. S.; Lindemuth, I. R.; Makhin, V.; Presura, R.; Ryutov, D. D.; Sheehey, P. T.; Siemon, R. E.; Sotnikov, V. I.

    2004-04-01

    A wall confined plasma in an inverse-pinch configuration holds potential as a plasma target for Magnetized Target Fusion (MTF) as well as a simple geometry to study wall-confined plasma. An experiment is planned to study the inverse-pinch configuration using the Zebra Z pinch [B. S. Bauer et al., AIP Conference Proceedings Vol. 409 (American Institute of Physics, Melville, 1997), p. 153] of the Nevada Terawatt Facility at the University of Nevada, Reno (UNR). The dynamics of the discharge formation have been analyzed using analytic models and numerical methods. Strong heating occurs by thermalization of directed energy when an outward moving current sheet (the inverse pinch effect) collides with the outer wall of the experimental chamber. Two-dimensional magnetohydrodynamic simulations show Rayleigh-Taylor and Richtmyer-Meshkov like modes of instability, as expected because of the shock acceleration during plasma formation phase. The instabilities are not disruptive, but give rise to a mild level of turbulence. The conclusion from this work is that an interesting experiment relevant to wall confinement for MTF could be done using existing equipment at UNR.

  10. Improvement of water quality using dielectric barrier discharge plasma

    Science.gov (United States)

    Quyen, N. T.; Traikool, T.; Nitisoravut, R.; Onjun, T.

    2017-06-01

    The improvement of water quality using by atmospheric plasma produced from a dielectric barrier discharge (DBD) was studied. An experiment was set-up with a 4 mm diameter pipe, which contains 2 electrodes and has an air flow with the rate of 15 liters per minute. Surface water, domestic wastewater and DI water were treated with the DBD plasma for some period of time. Electricity was supplied at 3.5 kV with the frequency of 5.5 kHz. Some key parameters of water quality includes the level of chemical oxygen demand (COD), total suspended solid (TSS), color, and odor are measured before and after. The result showed that strong acid with pH below 2 was observed after 60 minutes plasma treatment for the DI water, while the surface water and wastewater needs about 120 minutes to pH below 2 even though the pH value are about the same at the beginning. Moreover, It was formed that the COD, TSS microorganism was noticeably decreased, therefore the increasing of transparency level. This result confirms that atmospheric DBD plasma generated acidity in water as reduce amount of organic and suspended solid in water.

  11. Electrostatic modelling of dual frequency rf plasma discharges

    Energy Technology Data Exchange (ETDEWEB)

    Boyle, P C; Ellingboe, A R; Turner, M M [Plasma Research Laboratory, National Centre for Plasma Science and Technology and School of Physical Sciences, Dublin City University, Dublin 9 (Ireland)

    2004-08-01

    Particle-in-cell simulations have been used to study the nature of dual frequency plasma discharges. It is observed that both the ion flux on to the electrodes and the ion bombardment energy on to the electrodes can be controlled independently. There are two separate regimes in which this occurs. At large electrode separation, the ion current is controlled by varying the total discharge current, J{sub lf} + J{sub hf}. At small electrode separations, the ion flux can be controlled by varying the high frequency power source. In both regimes, the energy of the ions bombarding the electrodes is then determined by the low frequency voltage. A consequence of using dual frequencies to power the device is that the sheath width increases linearly as the low frequency power source is increased. This results in the dimensions of the bulk plasma decreasing, causing the electron temperature to increase for devices with electrode separations that are of comparable size to the electrode separation. In order to better understand the underlying physics involved within these devices an analytical global model has been developed which can explain many of the characteristics observed in the simulations.

  12. Hydrogen production from dimethyl ether using corona discharge plasma

    Science.gov (United States)

    Zou, Ji-Jun; Zhang, Yue-Ping; Liu, Chang-Jun

    Dimethyl ether (DME), with its non-toxic character, high H/C ratio and high-energy volumetric density, is an ideal resource for hydrogen production. In this work, hydrogen production from the decomposition of DME using corona discharge has been studied. The corona discharge plasma decomposition was conducted at ambient conditions. The effects of dilution gas (argon), flow rate, frequency and waveforms on the DME decomposition were investigated. The addition of dilution gas can significantly increase the hydrogen production rate. The highest hydrogen production rate with the lowest energy consumption presents at the flow rate of 27.5 Nml min -1. AC voltage is more favored than DC voltage for the production of hydrogen with less energy input. The optimal frequency is 2.0 kHz. The hydrogen production rate is also affected by the input waveform and decreases as following: sinusoid triangular > sinusoid > ramp > square, whereas the sinusoid waveform shows the highest energy efficiency. The corona discharge decomposition of DME is leading to a simple, easy and convenient hydrogen production with no needs of catalyst and external heating.

  13. Endotoxin removal by radio frequency gas plasma (glow discharge)

    Science.gov (United States)

    Poon, Angela

    2011-12-01

    Contaminants remaining on implantable medical devices, even following sterilization, include dangerous fever-causing residues of the outer lipopolysaccharide-rich membranes of Gram-negative bacteria such as the common gut microorganism E. coli. The conventional method for endotoxin removal is by Food & Drug Administration (FDA)-recommended dry-heat depyrogenation at 250°C for at least 45 minutes, an excessively time-consuming high-temperature technique not suitable for low-melting or heat-distortable biomaterials. This investigation evaluated the mechanism by which E. coli endotoxin contamination can be eliminated from surfaces during ambient temperature single 3-minute to cumulative 15-minute exposures to radio-frequency glow discharge (RFGD)-generated residual room air plasmas activated at 0.1-0.2 torr in a 35MHz electrodeless chamber. The main analytical technique for retained pyrogenic bio-activity was the Kinetic Chromogenic Limulus Amebocyte Lysate (LAL) Assay, sufficiently sensitive to document compliance with FDA-required Endotoxin Unit (EU) titers less than 20 EU per medical device by optical detection of enzymatic color development corresponding to water extracts of each device. The main analytical technique for identification of chemical compositions, amounts, and changes during sequential reference Endotoxin additions and subsequent RFGD-treatment removals from infrared (IR)-transparent germanium (Ge) prisms was Multiple Attenuated Internal Reflection (MAIR) infrared spectroscopy sensitive to even monolayer amounts of retained bio-contaminant. KimaxRTM 60 mm x 15 mm and 50mm x 15mm laboratory glass dishes and germanium internal reflection prisms were inoculated with E. coli bacterial endotoxin water suspensions at increments of 0.005, 0.05, 0.5, and 5 EU, and characterized by MAIR-IR spectroscopy of the dried residues on the Ge prisms and LAL Assay of sterile water extracts from both glass and Ge specimens. The Ge prism MAIR-IR measurements were

  14. Online diagnosis of electron excitation temperature in CH4+H2 discharge plasma at atmospheric pressure by optical emission spectra

    Institute of Scientific and Technical Information of China (English)

    CUI JinHua; XU ZhenFeng; ZHANG JiaLiang; NIE QiuYue; XU GenHui; REN LongLiang

    2008-01-01

    Methane coupling under low temperature plasmas at atmospheric pressure is a green process by use of renewable sources of energy.In this study,CH4+H2 dis-charge plasma was on-line diagnosed by optical emission spectra so as to char-acterize the discharge system and to do spade work for the optimization of the technical parameters for future commercial production of methane coupling under plasmas.The study was focused on a calculation method for the online diagnosis of the electron excitation temperature in CH4+H2 discharge plasma at atmospheric pressure.The diagnostic method is easy,efficient and fairly precise.A serious er-ror in a literature was corrected during the reasoning of its series of equations formerly used to calculate electron temperatures in plasmas.

  15. The α and γ plasma modes in plasma-enhanced atomic layer deposition with O2–N2 capacitive discharges

    Science.gov (United States)

    Napari, M.; Tarvainen, O.; Kinnunen, S.; Arstila, K.; Julin, J.; Fjellvåg, Ø. S.; Weibye, K.; Nilsen, O.; Sajavaara, T.

    2017-03-01

    Two distinguishable plasma modes in the O2–N2 radio frequency capacitively coupled plasma (CCP) used in remote plasma-enhanced atomic layer deposition (PEALD) were observed. Optical emission spectroscopy and spectra interpretation with rate coefficient analysis of the relevant processes were used to connect the detected modes to the α and γ modes of the CCP discharge. To investigate the effect of the plasma modes on the PEALD film growth, ZnO and TiO2 films were deposited using both modes and compared to the films deposited using direct plasma. The growth rate, thickness uniformity, elemental composition, and crystallinity of the films were found to correlate with the deposition mode. In remote CCP operations the transition to the γ mode can result in a parasitic discharge leading to uncontrollable film growth and thus limit the operation parameters of the capacitive discharge in the PEALD applications.

  16. Numerical study of capacitive coupled HBr/Cl2 plasma discharge for dry etch applications

    Science.gov (United States)

    Gul, Banat; Ahmad, Iftikhar; Zia, Gulfam; Aman-ur-Rehman

    2016-09-01

    HBr/Cl2 plasma discharge is investigated to study the etchant chemistry of this discharge by using the self-consistent fluid model. A comprehensive set of gas phase reactions (83 reactions) including primary processes such as excitation, dissociation, and ionization are considered in the model along with 24 species. Our findings illustrate that the densities of neutral species (i.e., Br, HCl, Cl, H, and H2) produced in the reactor are higher than charged species (i.e., Cl2+, Cl-, HBr+, and Cl+). Density profile of neutral and charged species followed bell shaped and double humped distributions, respectively. Increasing Cl2 fraction in the feedback gases (HBr/Cl2 from 90/10 to 10/90) promoted the production of Cl, Cl+, and Cl2+ in the plasma, indicating that chemical etching pathway may be preferred at high Cl-environment. These findings pave the way towards controlling/optimizing the Si-etching process.

  17. Extended dielectric relaxation scheme for fluid transport simulations of high density plasma discharges

    Science.gov (United States)

    Kwon, Deuk-Chul; Song, Mi-Young; Yoon, Jung-Sik

    2014-10-01

    It is well known that the dielectric relaxation scheme (DRS) can efficiently overcome the limitation on the simulation time step for fluid transport simulations of high density plasma discharges. By imitating a realistic and physical shielding process of electric field perturbation, the DRS overcomes the dielectric limitation on time step. However, the electric field was obtained with assuming the drift-diffusion approximation. Although the drift-diffusion expressions are good approximations for both the electrons and ions at high pressure, the inertial term cannot be neglected in the ion momentum equation for low pressure. Therefore, in this work, we developed the extended DRS by introducing an effective electric field. To compare the extended DRS with the previous method, two-dimensional fluid simulations for inductively coupled plasma discharges were performed. This work was supported by the Industrial Strategic Technology Development Program (10041637, Development of Dry Etch System for 10 nm class SADP Process) funded by the Ministry of Knowledge Economy (MKE, Korea).

  18. Correlation between discharging property and coatings microstructure during plasma electrolytic oxidation

    Institute of Scientific and Technical Information of China (English)

    GUAN Yong-jun; XIA Yuan

    2006-01-01

    The voltage-current properties during plasma electrolytic discharge were determined by measuring the current density and cell voltage as functions of processing time and then by mathematical transformation. Correlation between discharge I-V property and the coatings microstructure on aluminum alloy during plasma electrolytic oxidation was determined by comparing the voltage-current properties at different process stages with SEM results of the corresponding coatings. The results show that the uniform passive film corresponds to a I-V property with one critical voltage, and a compound of porous layer and sintered ceramic particles corresponds to a I-V property with two critical voltages. The growth regularity of PEO cermet coatings was also studied.

  19. Action of plasma jets of a low-current spark discharge on microorganisms ( Escherichia coli)

    Science.gov (United States)

    Baldanov, B. B.; Semenov, A. P.; Ranzhurov, Ts. V.; Nikolaev, E. O.; Gomboeva, S. V.

    2015-11-01

    High efficiency of bactericide action of cold argon plasma generated by plasma jets of a weak-current spark discharge under atmospheric pressure is demonstrated. It is found that an increase in the time of treatment with plasma jets from a low-current spark discharge makes it possible to effectively inactivate microorganisms over a much larger area.

  20. Generation of low-temperature air plasma for food processing

    Science.gov (United States)

    Stepanova, Olga; Demidova, Maria; Astafiev, Alexander; Pinchuk, Mikhail; Balkir, Pinar; Turantas, Fulya

    2015-11-01

    The project is aimed at developing a physical and technical foundation of generating plasma with low gas temperature at atmospheric pressure for food industry needs. As known, plasma has an antimicrobial effect on the numerous types of microorganisms, including those that cause food spoilage. In this work an original experimental setup has been developed for the treatment of different foods. It is based on initiating corona or dielectric-barrier discharge in a chamber filled with ambient air in combination with a certain helium admixture. The experimental setup provides various conditions of discharge generation (including discharge gap geometry, supply voltage, velocity of gas flow, content of helium admixture in air and working pressure) and allows for the measurement of the electrical discharge parameters. Some recommendations on choosing optimal conditions of discharge generation for experiments on plasma food processing are developed.

  1. Thrust Stand Measurements Using Alternative Propellants in the Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley K.; Polzin, Kurt A.

    2011-01-01

    Storable propellants (for example water, ammonia, and hydrazine) are attractive for deep space propulsion due to their naturally high density at ambient interplanetary conditions, which obviates the need for a cryogenic/venting system. Water in particular is attractive due to its ease of handling and availability both terrestrially and extra-terrestrially. While many storable propellants are reactive and corrosive, a propulsion scheme where the propellant is insulated from vulnerable (e.g. metallic) sections of the assembly would be well-suited to process these otherwise incompatible propellants. Pulsed inductive plasma thrusters meet this criterion because they can be operated without direct propellant-electrode interaction. During operation of these devices, electrical energy is capacitively stored and then discharged through an inductive coil creating a time-varying current in the coil that interacts with a plasma covering the face of the coil to induce a plasma current. Propellant is accelerated and expelled at a high exhaust velocity (O(10-100 km/s)) by the Lorentz body force arising from the interaction of the magnetic field and the induced plasma current. While this class of thruster mitigates the life-limiting issues associated with electrode erosion, many pulsed inductive plasma thrusters require high pulse energies to inductively ionize propellant. The Microwave Assisted Discharge Inductive Plasma Accelerator (MAD-IPA) is a pulsed inductive plasma thruster that addressees this issue by partially ionizing propellant inside a conical inductive coil before the main current pulse via an electron cyclotron resonance (ECR) discharge. The ECR plasma is produced using microwaves and a static magnetic field from a set of permanent magnets arranged to create a thin resonance region along the inner surface of the coil, restricting plasma formation, and in turn current sheet formation, to a region where the magnetic coupling between the plasma and the theta

  2. Rapid Formation of Distributed Plasma Discharges using X-Band Microwaves

    Science.gov (United States)

    Xiang, Xun

    Observations of rapidly formed (plasma discharges using high power X-band microwaves are presented. A cylindrical stainless steel chamber (15.2 cm long, 14.6 cm diameter) enclosed with polycarbonate windows (0.953 cm) was used to observe microwave breakdown in argon and neon gas mixtures from 50 to 250 torr. The chamber was illuminated by the output of a 16.2 kW, 800 ns pulse-width, 9.382 GHz magnetron with a 43 repetitive rate through an X-band waveguide pressed against the first polycarbonate window. Fast (50 ns) time-scale optical images of the plasma revealed the plasma formation and decay processes, as well as the plasma patterns for different plasma formation conditions. CST simulations were conducted to compare the electric field distribution inside the discharge chamber with the plasma patterns in the images. VUV (Vacuum Ultra-Violet) radiation was supported as the mechanism to enhance the plasma expansion and assist the formation of the plasma side lobes. Reflection Measurements showed 63% reflected power once plasma was formed, and a small amount of argon in neon shortened the breakdown time, verifying that the Penning effect lowers the breakdown threshold. Mixer measurements were taken, combined with a 1-D 6-region microwave plasma model to estimate the maximum effective plasma density as 2.2x1012 cm-3 with a corresponding maximum effective electron temperature of 2.5 eV in pure neon plasma at 100 torr under a Maxwellian distribution assumption. Optical emission spectroscopy (OES) assisted by the SPECAIR model determined the gas temperature in the microwave plasma as 350 +/- 50 K. OES line ratio measurements provided plasma parameters including time-evolved metastable and resonance densities, effective electron temperatures, electron densities for plasmas formed at 100 torr in pure neon and Ne/Ar (99:1) mixture gases. The comparison of time-evolved neon metastable and resonance densities in pure neon and Ne/Ar (99:1) mixture plasmas verified the Penning

  3. Simulation of Dual-Electrode Capacitively Coupled Plasma Discharges

    Science.gov (United States)

    Lu, Yijia; Ji, Linhong; Cheng, Jia

    2016-12-01

    Dual-electrode capacitively coupled plasma discharges are investigated here to lower the non-uniformity of plasma density. The dual-electrode structure proposed by Jung splits the electrode region and increases the flexibility of fine tuning non-uniformity. Different RF voltages, frequencies, phase-shifts and electrode areas are simulated and the influences are discussed. RF voltage and electrode area have a non-monotonic effect on non-uniformity, while frequency has a monotonic effect. Phase-shift has a cyclical influence on non-uniformity. A special combination of 224 V voltage and 11% area ratio with 10 MHz lowers the non-uniformity of the original set (200 V voltage and 0% area ratio with 10 MHz) by 46.5%. The position of the plasma density peak at the probe line has been tracked and properly tuning the phase-shift can obtain the same trace as tuning frequency or voltage. supported by National Natural Science Foundation of China (No. 51405261)

  4. Modification of Composite Material Fillers by Atmospheric Plasma Discharge

    Directory of Open Access Journals (Sweden)

    David Tichy

    2013-01-01

    Full Text Available This work is focused on the observation of the influence of cold atmospheric dielectric barrier discharge (DBD on a modification of textile samples. The main objective of the experiment is to research wettability change of textiles modified by different exposure times and also the observation of the influence of a modification ageing effect. An ambient air was used as a working gas for DBD plasma. The wettability evaluation was carried out by a drop method, in which an imprint of the dropwas observed on the textile surface during various time intervals. An ageing effect of the modification was monitored within an interval of 28 days. Considerable increase of wettability of all modified samples has been proved. A fibre surface analysis was carried out by means of SEM.

  5. Ionic Wind Phenomenon and Charge Carrier Mobility in Very High Density Argon Corona Discharge Plasma

    Science.gov (United States)

    Nur, M.; Bonifaci, N.; Denat, A.

    2014-04-01

    Wind ions phenomenon has been observed in the high density argon corona discharge plasma. Corona discharge plasma was produced by point to plane electrodes and high voltage DC. Light emission from the recombination process was observed visually. The light emission proper follow the electric field lines that occur between point and plane electrodes. By using saturation current, the mobilities of non-thermal electrons and ions have been obtained in argon gas and liquid with variation of density from 2,5 1021 to 2 1022 cm-3. In the case of ions, we found that the behaviour of the apparent mobility inversely proportional to the density or follow the Langevin variation law. For non-thermal electron, mobility decreases and approximately follows a variation of Langevin type until the density <= 0,25 the critical density of argon.

  6. Methane Incorporation into Liquid Fuel by Non-Equilibrium Plasma Discharges

    CERN Document Server

    Liu, Chong; Ji, Hai-Feng; Smith, Joshua; Rabinovich, Alexander; Dobrynin, Danil; Fridman, Alexander

    2016-01-01

    The conventional ways of processing natural gas into more efficient and economical fuels usually either have low conversion rate or low energy efficiency. In this work, a new approach of methane liquefaction is proposed. Instead of direct treatment of only natural gas, plasma activated methane is reacting with liquid fuel. In this way, methane molecules are directly incorporated onto liquid fuel to achieve liquefaction. Nanosecond-pulsed dielectric barrier discharge and atmospheric pressure glow discharge are used here to ensure no local heating in gas bubbles. Effects of both discharges on methane reaction with liquid fuel are investigated, mass and chemical changes in liquid are observed. Preliminary results show fixation of methane in liquid fuel.

  7. Dielectric barrier discharges: progress on plasma sources and on the understanding of regimes and single filaments

    Science.gov (United States)

    Brandenburg, Ronny

    2017-05-01

    Dielectric barrier discharges (DBDs) are plasmas generated in configurations with an insulating (dielectric) material between the electrodes which is responsible for a self-pulsing operation. DBDs are a typical example of nonthermal atmospheric or normal pressure gas discharges. Initially used for the generation of ozone, they have opened up many other fields of application. Therefore DBDs are a relevant tool in current plasma technology as well as an object for fundamental studies. Another motivation for further research is the fact that so-called partial discharges in insulated high voltage systems are special types of DBDs. The breakdown processes, the formation of structures, and the role of surface processes are currently under investigation. This review is intended to give an update to the already existing literature on DBDs considering the research and development within the last two decades. The main principles and different modes of discharge generation are summarized. A collection of known as well as special electrode configurations and reactor designs will be presented. This shall demonstrate the different and broad possibilities, but also the similarities and common aspects of devices for different fields of applications explored within the last years. The main part is devoted to the progress on the investigation of different aspects of breakdown and plasma formation with the focus on single filaments or microdischarges. This includes a summary of the current knowledge on the electrical characterization of filamentary DBDs. In particular, the recent new insights on the elementary volume and surface memory mechanisms in these discharges will be discussed. An outlook for the forthcoming challenges on research and development will be given.

  8. Conversion of methane through dielectric-barrier discharge plasma

    Institute of Scientific and Technical Information of China (English)

    Baowei WANG; Xiaolei CAO; Kuanhui YANG; Genhui XU

    2008-01-01

    Methane coupling to produce C2 hydrocar-bons through a dielectric-barrier discharge (DBD) plasma reaction was studied in four DBD reactors. The effects of high voltage electrode position, different discharge gap, types of inner electrode, volume ratio of hydrogen to methane and air cooling method on the conversion of methane and distribution of products were investigated. Conversion of methane is obviously lower when a high voltage electrode acts as an outer electrode than when it acts as an inner electrode. The lifting of reaction temper-ature becomes slow due to cooling of outer electrode and the temperature can be controlled in the expected range of 60℃-150℃ for ensuring better methane conversion and safe operation. The parameters of reactors have obvious effects on methane conversion, but it only slightly affects distribution of the products. The main products are ethyl-ene, ethane and propane. The selectivity of C2 hydrocar-bons can reach 74.50% when volume ratio of hydrogen to methane is 1.50.

  9. Stimulated Electromagnetic Emission Indicator of Glow Plasma Discharges from Ionospheric HF Wave Transmissions with HAARP

    Science.gov (United States)

    Bernhardt, P. A.; Scales, W.; Briczinski, S. J.; Fu, H.; Mahmoudian, A.; Samimi, A.

    2012-12-01

    High power radio waves resonantly interact with to accelerate electrons for production of artificial aurora and plasma clouds. These plasma clouds are formed when the HF frequency is tuned near a harmonic of the electron cyclotron frequency. At a narrow band resonance, large electrostatic fields are produced below the F-layer and the neutral atmosphere breaks down with a glow plasma discharge. The conditions for this resonance are given by matching the pump wave frequency and wave-number with the sum of daughter frequencies and wave-numbers for several plasma modes. The most likely plasma mode that accelerates the electrons is the electron Bernstein wave in conjunction with an ion acoustic wave. Both upper hybrid and whistler mode waves are also possible sources of electron acceleration. To determine the plasma process for electron acceleration, stimulated electromagnetic emissions are measured using ground receivers in a north-south chain from the HAARP site. Recent observations have shown that broad band spectral lines downshifted from the HF pump frequency are observed when artificial plasma clouds are formed. For HF transmissions are the 2nd, 3rd, and 4th gyro harmonic, the downshifted indicators are found 500 Hz, 20 kHz, and 140 kHz, respectively, from the pump frequency. This Indicator Mode (IM) anticipates that a plasma layer will be formed before it is recorded with an ionosonde or optical imager.

  10. Treatment of Wastewater with High Conductivity by Pulsed Discharge Plasma

    Science.gov (United States)

    Wang, Zhaojun; Jiang, Song; Liu, Kefu

    2014-07-01

    A wastewater treatment system was established by means of pulsed dielectric barrier discharge (DBD). The main advantage of this system is that the wastewater is employed as one of the electrodes for the degradation of rhodamine B, which makes use of the high conductivity and lessenes its negative influence on the discharge process. At the same time, the reactive species like ozone and ultraviolet (UV) light generated by the DBD can be utilized for the treatment of wastewater. The effects of some factors like conductivity, peak pulse voltage, discharge frequency and pH values were investigated. The results show that the combination of these reactive species could enhance the degradation of the dye while the ozone played the most important role in the process. The degradation efficiency was enhanced with the increase of energy supplied. The reduction in the concentration of rhodamine B was much more effective with high solution conductivity; under the highest conductivity condition, the degradation rate could rise to 99%.

  11. Polarity functions' characterization and the mechanism of starch modification by DC glow discharge plasma.

    Science.gov (United States)

    Khorram, S; Zakerhamidi, M S; Karimzadeh, Z

    2015-01-01

    The wheat starch was investigated, before and after exposure to the argon and oxygen glow discharge plasma, without any added chemical reagents, using a novel media polarity functions method. The mechanisms of modification of starch in plasma discharge irradiation were explained using some methods such as; NMR, IR spectroscopy, Kamlet-Abboud-Taft polarity functions (specific and nonspecific interaction) of modified starch. The starch modification, by plasma treatment, shows valuable changes with plasma gas and relative ionized or active species. Characterizations indicate that argon glow discharge plasma increases crosslink in C-2 site of starch. Also, oxygen plasma discharge irradiation tends to oxidize the OH group in C-6 site of carbonyl group. Furthermore, the reported mechanisms show the highest efficiency, because of the stereo-chemical orientation of active sites of starch and plasma potential of wall in plasma media. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Effects of design and operating variables on process characteristics in a methane discharge: a numerical study

    Science.gov (United States)

    Bera, K.; Farouk, B.; Lee, Y. H.

    2001-05-01

    A self-consistent two-dimensional radio frequency capacitively coupled glow discharge model has been developed in cylindrical coordinates for a methane discharge using a fluid model. The objective of the study is to identify the effects of design and operating variables of the reactor on the process characteristics such as the deposition rate, uniformity and the quality of the diamond-like-carbon film. The simulations provide insights to charged species dynamics and investigate their effects on the plasma process for a depositing methane discharge. The model includes continuity equations for electrons and positive and negative ions, and energy equation for electrons. Swarm data as a function of electron energy are provided as input to the model. The model predicts the electron density, ion density, and their fluxes and energies to the cathode. The roles of electrons, dominating ions and radicals in a capacitively coupled discharge are investigated. The radical and neutral densities in the discharge are calculated using a gas phase chemistry model. The diamond-like-carbon thin-film deposition rate is predicted using surface chemistry model. The gas phase chemistry model considers diffusion of radicals and neutrals along with creation and loss terms. The surface deposition/etching process involves adsorption-desorption, adsorption layer reaction, ion stitching, direct ion incorporation, etching and carbon sputtering. A systematic parametric study of plasma processing has been performed to identify process parameters to obtain better film deposition/etching on a wafer. The present work shows how plasma equipment simulation can be used for the practical investigation and optimization of a plasma-assisted chemical vapour deposition process. The simultaneous treatment of plasma dynamics and surface processes enables a very precise prediction of the process characteristics in terms of the film deposition rate, uniformity and the quality as functions of discharge control

  13. Influence of Plasma Temperature on the Concentration of NO Produced by Pulsed Arc Discharge

    Institute of Scientific and Technical Information of China (English)

    胡辉; 陈卫鹏; 张锦丽; 陆僖; 何俊佳

    2012-01-01

    This study conducted experiments on producing inhaled medical nitric oxide (iNO) by pulsed arc discharge in dry and clean air under different discharge current. The concentration of NO and NO2 produced by air discharge, as well as the change of the ratio of NO2/NO under different discharge current were investigated. Through the analysis of plasma emission spectrum, the relationship between discharge current and arc plasma temperature was studied. The results indicate that, as discharge current increases, the arc plasma temperature increases, which then leads to the increase of NO concentration, the decrease of NO2 concentration, and the rapid decrease of the ratio of NO2/NO. When the plasma temperature is 9000 K, the ratio of NO2/NO is approximately 60%, while when the plasma temperature varies between 10550 K and 11300 K, the NO2/NO ratio is within the range of 4.2% to 4.6%.

  14. Gene Transfection Method Using Atmospheric Pressure Dielectric-Barrier Discharge Plasmas

    Science.gov (United States)

    Sasaki, Shota; Kanzaki, Makoto; Kaneko, Toshiro

    2013-09-01

    Gene transfection which is the process of deliberately introducing nucleic acids into cells is expected to play an important role in medical treatment because the process is necessary for gene therapy and creation of induced pluripotent stem (iPS) cells. However, the conventional transfection methods have some problems, so we focus attention on promising transfection methods by atmospheric pressure dielectric-barrier discharge (AP-DBD) plasmas. AP-DBD He plasmas are irradiated to the living cell covered with genes. Preliminarily, we use fluorescent dye YOYO-1 instead of the genes and use LIVE/DEAD Stain for cell viability test, and we analyze the transfection efficiency and cell viability under the various conditions. It is clarified that the transfection efficiency is strongly dependence on the plasma irradiation time and cell viability rates is high rates (>90%) regardless of long plasma irradiation time. These results suggest that ROS (Reactive Oxygen Species) and electric field generated by the plasma affect the gene transfection. In addition to this (the plasma irradiation time) dependency, we now investigate the effect of the plasma irradiation under the various conditions.

  15. Physical and plasmachemical aspects of diffuse coplanar barrier discharge as a novel atmospheric-pressure plasma source

    Science.gov (United States)

    Cernak, M.; Kovacik, D.; Zahoranova, A.; Rahel, J.

    2008-07-01

    Collaborating Czech and Slovakian university teams have recently developed an innovative plasma source, the so-called Diffuse Coplanar Surface Barrier Discharge (DCSBD), which has the potential to move a step closer to the industry requirement for in-line treatment of low-added-value materials using a highly-nonequlibrium ambient air plasma (Simor et al. 2002, The idea is to generate a thin (on the order of 0.1 mm) layer of highly-nonequlibrium plasma with a high power density (up to 100 W/cm^3) in the immediate vicinity of the treated surface and bring it into a close contact with the treated surface. Comparing to atmospheric-pressure glow discharge, volume dielectric barrier discharge, and plasma jet plasmas, such a diffuse plasma layer is believed to provide substantial advantages in energy consumption, exposure time, and technical simplicity. A brief outline of physical mechanism and basic properties of DCSBD will given using the results of emission spectroscopy, high-speed camera, and spatially resolved cross-correlation spectroscopy studies. The presentation will review also a current state of the art in in-line plasma treatment of low-cost materials and opportunities for the use of the so-called Diffuse Coplanar Surface Dielectric Barrier Discharge (DCSBD). The results obtained on the ambient air plasma treatments of textile, paper, wood, and glass illustrate that DCSBD offers outstanding performance with extremely low energy consumption for large area, uniform surface modifications of materials under continuous process conditions.

  16. Plasma decay in high-voltage nanosecond discharges in oxygen-containing mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Anokhin, E. M.; Popov, M. A. [Moscow Institute of Physics and Technology (Russian Federation); Kochetov, I. V. [Troitsk Institute for Innovation and Fusion Research (Russian Federation); Aleksandrov, N. L., E-mail: nick-aleksandrov@mail.ru [Moscow Institute of Physics and Technology (Russian Federation); Starikovskii, A. Yu. [Princeton University (United States)

    2016-01-15

    Plasma decay in high-voltage nanosecond discharges in CO{sub 2}: O{sub 2} and Ar: O{sub 2} mixtures at room gas temperature and a pressure of 10 Torr is studied experimentally and theoretically. The time dependence of the electron density during plasma decay is measured using microwave interferometry. The time evolution of the charged particle density, ion composition, and electron temperature is simulated numerically. It is shown that, under the given conditions, the discharge plasma is dominated for the most time by O{sub 2}{sup +} ions and plasma decay is determined by dissociative and three-body electron−ion recombination. As in the previous studies performed for air and oxygen plasmas, agreement between measurements and calculations is achieved only under the assumption that the rate of three-body recombination of molecular ions is much greater than that for atomic ions. The values of the rate constant of three-body recombination of electrons with O{sub 2}{sup +} ions in a wide range of electron temperatures (500–5500 K), as well as for thermal (300 K) electrons, are obtained by processing the experimental results.

  17. Plasma Processing of Materials

    Science.gov (United States)

    1985-02-22

    used in France. In this case, three ’ movable electrodes arranged about the central axis with a coaxial sheath gas are employed. Initially the...Demiocratic Republic plasma furnace. chrome -magnesite; the bottom section is lined with rammed chrome -magnesite refractory. Due to the high heat loads... sheath injector design, cathode tip shape, and degree of water cooling are important parameters in providing a stable, uncontaminating, long-lifetime

  18. Decomposition of toluene in a gliding arc discharge plasma reactor

    Energy Technology Data Exchange (ETDEWEB)

    Du Changming [School of Environmental Science and Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Yan Jianhua [Institute for Thermal Power Engineering, Zhejiang University, Hangzhou 310027 (China); Cheron, Bruno [UMR 6614 (CORIA), University of Rouen, 76821 Mont Saint Aignan (France)

    2007-11-15

    The decomposition of toluene in a gliding arc discharge (glidarc) was performed and studied. Experimental results indicate that the glidarc technology can effectively decompose toluene molecules and has bright prospects of being applied as an alternative tool to decompose volatile organic compounds. It is found that a change in the electrode material had an insignificant effect on the toluene removal efficiency. The toluene removal efficiency increases with increasing inlet gas temperature. The water vapor present in the gas mixture has a favorable effect on the toluene decomposition in the plasma. The energy efficiency is 29.46 g (kWh{sup -1}) at a relative humidity of 50% and a specific energy input of 0.26 kWh m{sup -3}, which is higher than other types of non-thermal plasmas. Too much or too little oxygen content does not favor toluene decomposition. The major gas phase products detected by FT-IR from the decomposition of toluene with air participation were CO, CO{sub 2}, H{sub 2}O and NO{sub 2}. Some brown depositions were found on the surface of the electrodes, which were polar oxygenous and nitrogenous compounds determined by the GC-MS analysis, such as benzaldehyde, benzoic acid, quinine and nitrophenol from the reaction of toluene with radicals. A possible mechanism for toluene destruction via glidarc technology is proposed and summarized.

  19. Comparison of atmospheric air plasmas excited by high-voltage nanosecond pulsed discharge and sinusoidal alternating current discharge

    Science.gov (United States)

    Zhang, Shuai; Wang, Wen-chun; Jiang, Peng-chao; Yang, De-zheng; Jia, Li; Wang, Sen

    2013-10-01

    In this paper, atmospheric pressure air discharge plasma in quartz tube is excited by 15 ns high-voltage nanosecond pulsed discharge (HVNPD) and sinusoidal alternating current discharge (SACD), respectively, and a comparison study of these two kinds of discharges is made through visual imaging, electrical characterization, optical detection of active species, and plasma gas temperature. The peak voltage of the power supplies is kept at 16 kV while the pulse repetition rate of nanosecond pulse power supply is 100 Hz, and the frequency of sinusoidal power supply is 10 kHz. Results show that the HVNPD is uniform while the SACD presents filamentary mode. For exciting the same cycles of discharge, the average energy consumption in HVNPD is about 1/13 of the SACD. However, the chemical active species generated by the HVNPD is about 2-9 times than that excited by the SACD. Meanwhile, the rotational and vibrational temperatures have been obtained via fitting the simulated spectrum of N2 (C3Πu → B3Πg, 0-2) with the measured one, and the results show that the plasma gas temperature in the HVNPD remains close to room temperature whereas the plasma gas temperature in the SACD is about 200 K higher than that in HVNPD in the initial phase and continually increases as discharge exposure time goes on.

  20. Degradation of Microcystin-LR by Gas-Liquid Interfacial Discharge Plasma

    Science.gov (United States)

    Xin, Qing; Zhang, Yi; Wu, Kaibin

    2013-12-01

    In this study, we report on the degradation of microcystin-LR (MC-LR) by gas-liquid interfacial discharge plasma. The influences of operation parameters such as average input voltage, electrode distance and gas flow rate are investigated. Experimental results indicate that the input voltage and gas flow rate have positive influences on MC-LR degradation, while the electrode distance has a negative one. After 6 min discharge with 25 kV average input voltage and 60 L/h air aeration, the degradation rate of MC-LR achieves 75.3%. H2O2 and O3 generated by discharge both in distilled water and MC-LR solution are measured. Moreover, an emission spectroscopy is used as an indicator of the processes that take place on the gas-liquid boundary and inside plasma. Varied types of radicals (O, ·OH, CO, O3, etc.) are proved to be present in the gas phase during gas-liquid interfacial discharge.

  1. Conversion of natural gas to C2 hydrocarbons through dielectric-barrier discharge plasma catalysis

    Institute of Scientific and Technical Information of China (English)

    王保伟; 许根慧

    2002-01-01

    The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C2 hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H2/CH4, flow rate and catalyst on conversion of methane and selectivity of C2 hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C2 hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20-40 kV (8.4-40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20-60 ml · min-1. The conversion of methane can reach 45%, the selectivity of C2 hydrocarbons i

  2. Analysis of the growth of concomitant nitride layers produced by a post-discharge assisted process

    Energy Technology Data Exchange (ETDEWEB)

    Oseguera, J. [ITESM-CEM, Carretera al Lago de Guadalupe km. 3.5 Atizapan, 52926 (Mexico)]. E-mail: joseguer@itesm.mx; Castillo, F. [ITESM-CEM, Carretera al Lago de Guadalupe km. 3.5 Atizapan, 52926 (Mexico); Gomez, A. [UFRO, Av. Francisco Salazar 01145, Temuco, Casilla 54-d (Chile); Fraguela, A. [BUAP, Rio Verde y Ave. San Claudio, San Manuel, Puebla, 72570 (Mexico)

    2006-11-23

    In the present work, the growth of concomitant nitride layers during a post-discharge process is studied. The analysis takes into account the similarities and differences between nitriding post-discharge processes and other nitriding processes, employing a mathematical simulation of nitrogen diffusion. The considered differences are related to the thermodynamic standard states, the nitrogen concentration on the surface and the sputtering of the surface (this one for plasma processes). Nitrogen diffusion and layer formation are described from the beginning of the process by means of a mathematical model.

  3. Comparative study of NO removal in surface-plasma and volume-plasma reactors based on pulsed corona discharges.

    Science.gov (United States)

    Malik, Muhammad Arif; Kolb, Juergen F; Sun, Yaohong; Schoenbach, Karl H

    2011-12-15

    Nitric oxide (NO) conversion has been studied for two different types of atmospheric-pressure pulsed-corona discharges, one generates a surface-plasma and the other provides a volume-plasma. For both types of discharges the energy cost for NO removal increases with decreasing oxygen concentration and initial concentration of NO. However, the energy cost for volume plasmas for 50% NO removal, EC(50), from air was found to be 120 eV/molecule, whereas for the surface plasma, it was only 70 eV/molecule. A smaller difference in energy cost, but a higher efficiency for removal of NO was obtained in a pure nitrogen atmosphere, where NO formation is restricted due to the lack of oxygen. For the volume plasma, EC(50) in this case was measured at 50 eV/molecule, and for the surface plasma it was 40 eV/molecule. Besides the higher NO removal efficiency of surface plasmas compared to volume plasmas, the energy efficiency of surface-plasmas was found to be almost independent of the amount of electrical energy deposited in the discharge, whereas the efficiency for volume plasmas decreases considerably with increasing energy. This indicates the possibility of operating surface plasma discharges at high energy densities and in more compact reactors than conventional volume discharges.

  4. Comparative study of NO removal in surface-plasma and volume-plasma reactors based on pulsed corona discharges

    Energy Technology Data Exchange (ETDEWEB)

    Malik, Muhammad Arif, E-mail: MArifMalik@gmail.com [Frank Reidy Research Center for Bioelectrics, Old Dominion University, 4211 Monarch Way, Suite 300, Norfolk, VA 23508 (United States); Kolb, Juergen F.; Sun, Yaohong; Schoenbach, Karl H. [Frank Reidy Research Center for Bioelectrics, Old Dominion University, 4211 Monarch Way, Suite 300, Norfolk, VA 23508 (United States)

    2011-12-15

    Nitric oxide (NO) conversion has been studied for two different types of atmospheric-pressure pulsed-corona discharges, one generates a surface-plasma and the other provides a volume-plasma. For both types of discharges the energy cost for NO removal increases with decreasing oxygen concentration and initial concentration of NO. However, the energy cost for volume plasmas for 50% NO removal, EC{sub 50}, from air was found to be 120 eV/molecule, whereas for the surface plasma, it was only 70 eV/molecule. A smaller difference in energy cost, but a higher efficiency for removal of NO was obtained in a pure nitrogen atmosphere, where NO formation is restricted due to the lack of oxygen. For the volume plasma, EC{sub 50} in this case was measured at 50 eV/molecule, and for the surface plasma it was 40 eV/molecule. Besides the higher NO removal efficiency of surface plasmas compared to volume plasmas, the energy efficiency of surface-plasmas was found to be almost independent of the amount of electrical energy deposited in the discharge, whereas the efficiency for volume plasmas decreases considerably with increasing energy. This indicates the possibility of operating surface plasma discharges at high energy densities and in more compact reactors than conventional volume discharges.

  5. Degradation of triclosan in aqueous solution by dielectric barrier discharge plasma combined with activated carbon fibers.

    Science.gov (United States)

    Xin, Lu; Sun, Yabing; Feng, Jingwei; Wang, Jian; He, Dong

    2016-02-01

    The degradation of triclosan (TCS) in aqueous solution by dielectric barrier discharge (DBD) plasma with activated carbon fibers (ACFs) was investigated. In this study, ACFs and DBD plasma coexisted in a planar DBD plasma reactor, which could synchronously achieve degradation of TCS, modification and in situ regeneration of ACFs, enhancing the effect of recycling of ACFs. The properties of ACFs before and after modification by DBD plasma were characterized by BET and XPS. Various processing parameters affecting the synergetic degradation of TCS were also investigated. The results exhibited excellent synergetic effects in DBD plasma-ACFs system on TCS degradation. The degradation efficiency of 120 mL TCS with initial concentration of 10 mg L(-1) could reach 93% with 1 mm thick ACFs in 18 min at input power of 80 W, compared with 85% by single DBD plasma. Meanwhile, the removal rate of total organic carbon increased from 12% at pH 6.26-24% at pH 3.50. ACFs could ameliorate the degradation efficiency for planar DBD plasma when treating TCS solution at high flow rates or at low initial concentrations. A possible degradation pathway of TCS was investigated according to the detected intermediates, which were identified by liquid chromatography-hybrid quadrupole time-of-flight mass spectrometry (LC-QTOF-MS) combined with theoretical calculation of Gaussian 09 program.

  6. Comparison Between Dielectric Barrier Discharge Plasma and Ozone Regenerations of Activated Carbon Exhausted with Pentachlorophenol

    Science.gov (United States)

    Qu, Guangzhou; Liang, Dongli; Qu, Dong; Huang, Yimei; Li, Jie

    2014-06-01

    In this study, two regeneration methods (dielectric barrier discharge (DBD) plasma and ozone (O3) regeneration) of saturated granular activated carbon (GAC) with pentachlorophenol (PCP) were compared. The results show that the two regeneration methods can eliminate contaminants from GAC and recover its adsorption properties to some extent. Comparing the DBD plasma with O3 regeneration, the adsorption rate and the capacity of the GAC samples after DBD plasma regeneration are greater than those after O3 regeneration. O3 regeneration decreases the specific surface area of GAC and increases the acidic surface oxygen groups on the surface of GAC, which causes a decrease in PCP on GAC uptake. With increasing regeneration cycles, the regeneration efficiencies of the two methods decrease, but the decrease in the regeneration efficiencies of GAC after O3 regeneration is very obvious compared with that after DBD plasma regeneration. Furthermore, the equilibrium data were fitted by the Freundlich and Langmuir models using the non-linear regression technique, and all the adsorption equilibrium isotherms fit the Langmuir model fairly well, which demonstrates that the DBD plasma and ozone regeneration processes do not appear to modify the adsorption process, but to shift the equilibrium towards lower adsorption concentrations. Analyses of the weight loss of GAC show that O3 regeneration has a lower weight loss than DBD plasma regeneration.

  7. Relationship between the discharge mode and the spatial oxygen plasma distribution in a large size ferrite inductively coupled plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyun Jun [Department of Electrical Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); R and D Center for PSK-INC Corporation, Hwaseong-si 445-170 (Korea, Republic of); Hwang, Hye Ju; Cho, Jeong Hee; Chae, Hee Sun [R and D Center for PSK-INC Corporation, Hwaseong-si 445-170 (Korea, Republic of); Kim, Dong Hwan [Department of Nanoscale Semiconductor Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Chung, Chin-Wook, E-mail: joykang@hanyang.ac.kr [Department of Electrical Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of)

    2015-04-15

    The electrical characteristics and the spatial distribution of oxygen plasma according to the number of turns in ferrite inductively coupled plasmas (ferrite ICPs) are investigated. Through a new ICP model, which includes the capacitive coupling and the power loss of the ferrite material with the conventional ICP model, the variation of the oxygen discharge characteristics depending on the number of turns is simply understood by the electrical measurement, such as the antenna voltages and the currents. As the number of the turns increases, the capacitive coupling dominantly affects the spatial plasma distribution. This capacitive coupling results in a center focused density profile along the radial direction. In spite of the same discharge conditions (discharge chamber, neutral gas, and pressure), the spatial plasma distribution over 450 mm has drastic changes by increasing number of the turns. In addition, the effect of the negative species to the density profile is compared with the argon discharge characteristics at the same discharge configuration.

  8. Modeling a short cold cathode DC discharge device with controllable plasma parameters

    Science.gov (United States)

    Kudryavtsev, Anatoly; Adams, Steven; Demidov, Vladimir; Bogdanov, Yevgeny

    2009-11-01

    A short (without positive column) DC gas-discharge device with a cold cathode has been modeled. The device consists of the plane disk-shaped cathode and anode while the inter-electrode gap is bounded by a cylindrical wall. The cathode and anode are each 2.5 cm in diameter, and the inter-electrode gap is 12 mm. The wall is made of conducting parts divided by an insulator. The modeling has been performed for argon plasma at 1 Torr pressure. It is demonstrated in the model that spatial distributions of electron density and temperature and argon metastable atom density depend on the DC voltage applied to different conducting parts of the wall. Applied voltage can trap within the device volume energetic electrons arising from atomic and molecular processes in the plasma. This leads to a modification in the heating of slow electrons by energetic electrons and as a result modifies the controlling plasma parameters.

  9. Feasibility of arc-discharge and plasma-sputtering methods in cleaning plasma-facing and diagnostics components of fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hakola, Antti, E-mail: antti.hakola@vtt.fi [VTT Technical Research Centre of Finland, VTT (Finland); Likonen, Jari [VTT Technical Research Centre of Finland, VTT (Finland); Karhunen, Juuso; Korhonen, Juuso T. [Department of Applied Physics, Aalto University (Finland); Aints, Märt; Laan, Matti; Paris, Peeter [Department of Physics, University of Tartu (Estonia); Kolehmainen, Jukka; Koskinen, Mika; Tervakangas, Sanna [DIARC-Technology Oy, Espoo (Finland)

    2015-10-15

    Highlights: • Feasibility of the arc-discharge and plasma-sputtering techniques in removing deposited layers from ITER-relevant samples demonstrated. • Samples with the size of an A4 paper can be cleaned from 1-μm thick deposited layers in 10–20 minutes by the arc-discharge method. • The plasma-sputtering method is 5–10 times slower but the resulting surfaces are very smooth. • Arc-discharge method could be used for rapid cleaning of plasma-facing components during maintenance shutdowns of ITER, plasma sputtering is preferred for diagnostics mirrors. - Abstract: We have studied the feasibility of arc-discharge and plasma-sputtering methods in removing deposited layers from ITER-relevant test samples. Prototype devices have been designed and constructed for the experiments and the cleaning process is monitored by a spectral detection system. The present version of the arc-discharge device is capable of removing 1-μm thick layers from 350-mm{sup 2} areas in 4–8 s, but due to the increased roughness of the cleaned surfaces and signs of local melting, mirror-like surfaces cannot be treated by this technique. The plasma-sputtering approach, for its part, is some 5–10 times slower in removing the deposited layers but no changes in surface roughness or morphology of the samples could be observed after the cleaning phase. The arc-discharge technique could therefore be used for rapid cleaning of plasma-facing components during maintenance shutdowns of ITER while in the case of diagnostics mirrors plasma sputtering is preferred.

  10. Online diagnosis of electron excitation temperature in CH4+H2 discharge plasma at atmospheric pressure by optical emission spectra

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Methane coupling under low temperature plasmas at atmospheric pressure is a green process by use of renewable sources of energy. In this study, CH4+H2 dis- charge plasma was on-line diagnosed by optical emission spectra so as to char- acterize the discharge system and to do spade work for the optimization of the technical parameters for future commercial production of methane coupling under plasmas. The study was focused on a calculation method for the online diagnosis of the electron excitation temperature in CH4+H2 discharge plasma at atmospheric pressure. The diagnostic method is easy, efficient and fairly precise. A serious er- ror in a literature was corrected during the reasoning of its series of equations formerly used to calculate electron temperatures in plasmas.

  11. Effect of dielectric and liquid on plasma sterilization using dielectric barrier discharge plasma.

    Directory of Open Access Journals (Sweden)

    Navya Mastanaiah

    Full Text Available Plasma sterilization offers a faster, less toxic and versatile alternative to conventional sterilization methods. Using a relatively small, low temperature, atmospheric, dielectric barrier discharge surface plasma generator, we achieved ≥ 6 log reduction in concentration of vegetative bacterial and yeast cells within 4 minutes and ≥ 6 log reduction of Geobacillus stearothermophilus spores within 20 minutes. Plasma sterilization is influenced by a wide variety of factors. Two factors studied in this particular paper are the effect of using different dielectric substrates and the significance of the amount of liquid on the dielectric surface. Of the two dielectric substrates tested (FR4 and semi-ceramic (SC, it is noted that the FR4 is more efficient in terms of time taken for complete inactivation. FR4 is more efficient at generating plasma as shown by the intensity of spectral peaks, amount of ozone generated, the power used and the speed of killing vegetative cells. The surface temperature during plasma generation is also higher in the case of FR4. An inoculated FR4 or SC device produces less ozone than the respective clean devices. Temperature studies show that the surface temperatures reached during plasma generation are in the range of 30°C-66 °C (for FR4 and 20 °C-49 °C (for SC. Surface temperatures during plasma generation of inoculated devices are lower than the corresponding temperatures of clean devices. pH studies indicate a slight reduction in pH value due to plasma generation, which implies that while temperature and acidification may play a minor role in DBD plasma sterilization, the presence of the liquid on the dielectric surface hampers sterilization and as the liquid evaporates, sterilization improves.

  12. Characterization of stationary and pulsed inductively coupled RF discharges for plasma sterilization

    Science.gov (United States)

    Gans, T.; Osiac, M.; O'Connell, D.; Kadetov, V. A.; Czarnetzki, U.; Schwarz-Selinger, T.; Halfmann, H.; Awakowicz, P.

    2005-05-01

    Sterilization of bio-medical materials using radio frequency (RF) excited inductively coupled plasmas (ICPs) has been investigated. A double ICP has been developed and studied for homogenous treatment of three-dimensional objects. Sterilization is achieved through a combination of ultraviolet light, ion bombardment and radical treatment. For temperature sensitive materials, the process temperature is a crucial parameter. Pulsing of the plasma reduces the time average heat strain and also provides additional control of the various sterilization mechanisms. Certain aspects of pulsed plasmas are, however, not yet fully understood. Phase resolved optical emission spectroscopy and time resolved ion energy analysis illustrate that a pulsed ICP ignites capacitively before reaching a stable inductive mode. Time resolved investigations of the post-discharge, after switching off the RF power, show that the plasma boundary sheath in front of a substrate does not fully collapse for the case of hydrogen discharges. This is explained by electron heating through super-elastic collisions with vibrationally excited hydrogen molecules.

  13. A low power miniaturized dielectric barrier discharge based atmospheric pressure plasma jet

    Science.gov (United States)

    Divya Deepak, G.; Joshi, N. K.; Pal, Dharmendra Kumar; Prakash, Ram

    2017-01-01

    In this paper, a dielectric barrier discharge plasma based atmospheric pressure plasma jet has been generated in a floating helix and floating end ring electrode configuration using argon and helium gases. This configuration is subjected to a range of supply frequencies (10-25 kHz) and supply voltages (2-6 kV) at a fixed rate of gas flow rate (i.e., 1 l/min). The electrical characterization of the plasma jet has been carried out using a high voltage probe and current transformer. The current-voltage characteristics have been analyzed, and the consumed power has been estimated at different applied combinations for optimum power consumption at maximum jet length. The obtained optimum power and jet length for argon and helium gases are 12 mW and 32 mm, and 7.7 mW and 42 mm, respectively. It is inferred that besides the electrode configurations, the discharge gas is also playing a significant role in the low power operation of the cold plasma jet at maximum jet length. The obtained results are interpreted on the basis of penning processes.

  14. Spectroscopic study of plasma evolution in runaway nanosecond atmospheric-pressure He discharges.

    Science.gov (United States)

    Yatom, S; Stambulchik, E; Vekselman, V; Krasik, Ya E

    2013-07-01

    Time- and space-resolved visible-emission spectroscopy measurements are applied to study plasma parameters in nanosecond electrical discharges in He gas at pressure of 10(5) Pa, using a 150 kV, 5 ns duration high-voltage pulse. The plasma evolution during the discharge is investigated by applying line-shape analysis of several He I spectral transitions, with the Stark and opacity effects accounted for. The analysis shows that the discharge plasma is not in equilibrium and that significant electric fields of several kV/cm are present in the plasma during the discharge. Regions of plasma with significantly different electron densities are identified and a qualitative model of the plasma formation and evolution is proposed.

  15. Assessment of cytotoxic effect mechanisms of gas-discharge plasma radiation

    OpenAIRE

    Ivanova I.P.; Trofimova S.V.; Vedunova М.V.; Zhabereva А.S.; Bugrova M.L.; Piskaryov I.M.; Karpel Vel Leitner N.

    2014-01-01

    The aim of the investigation was to assess the mechanisms of cytotoxic effect of gas-discharge plasma radiation on lymphosarcoma and breast cancer cells. Materials and Methods. The experiment was carried out on the strains of rat lymphosarcoma (LSR) and breast cancer (RMK1) cells. 4 ml of cell suspension at (4–6)·106/ml concentration was exposed to gas-discharge plasma radiation in various time modes. Plasma radiation was generated by impulse device with the following set characteristics:...

  16. Long-Lived Vortex Structures in Collisional Pure and Gas-Discharge Nonneutral Electron Plasmas

    OpenAIRE

    Kervalishvili, N. A.

    2013-01-01

    The analysis of experimental investigations of equilibrium, interaction and dynamics of vortex structures in pure electron and gas-discharge electron nonneutral plasmas during the time much more than the electron-neutral collision time has been carried out. The problem of long confinement of the column of pure electron plasma in Penning-Malmberg trap is considered. The mechanism of stability of long-lived vortex structure in gas-discharge nonneutral electron plasma is investigated. The collap...

  17. Conditions for uniform impact of the plasma of a runaway-electron-induced pulsed diffuse discharge on an anode

    Science.gov (United States)

    Erofeev, M. V.; Baksht, E. Kh.; Burachenko, A. G.; Tarasenko, V. F.

    2015-09-01

    The subject matters in this work are (i) the spatial structure of a volume (diffuse) discharge initiated in atmospheric-pressure air in a heavily nonuniform electric field by nanosecond voltage pulses and (ii) the influence of its plasma on the surface of a plane aluminum anode. It is shown that a diffuse discharge initiated by nanosecond voltage pulses makes it possible to uniformly process the anode's surface in atmospheric-pressure air in contrast to a spark discharge, which results in microcracking, locally changes the surface properties, and thereby degrades the surface.

  18. Gas discharge plasmas are effective in inactivating Bacillus and Clostridium spores.

    Science.gov (United States)

    Tseng, Shawn; Abramzon, Nina; Jackson, James O; Lin, Wei-Jen

    2012-03-01

    Bacterial spores are the most resistant form of life and have been a major threat to public health and food safety. Nonthermal atmospheric gas discharge plasma is a novel sterilization method that leaves no chemical residue. In our study, a helium radio-frequency cold plasma jet was used to examine its sporicidal effect on selected strains of Bacillus and Clostridium. The species tested included Bacillus subtilis, Bacillus stearothermophilus, Clostridium sporogenes, Clostridium perfringens, Clostridium difficile, and Clostridium botulinum type A and type E. The plasmas were effective in inactivating selected Bacillus and Clostridia spores with D values (decimal reduction time) ranging from 2 to 8 min. Among all spores tested, C. botulinum type A and C. sporogenes were significantly more resistant to plasma inactivation than other species. Observations by phase contrast microscopy showed that B. subtilis spores were severely damaged by plasmas and the majority of the treated spores were unable to initiate the germination process. There was no detectable fragmentation of the DNA when the spores were treated for up to 20 min. The release of dipicolinic acid was observed almost immediately after the plasma treatment, indicating the spore envelope damage could occur quickly resulting in dipicolinic acid release and the reduction of spore resistance.

  19. Shock Formation by Plasma Filaments of Microwave Discharge under Atmospheric Pressure

    Science.gov (United States)

    Takahashi, Masayuki; Ohnishi, Naofumi

    2016-03-01

    A one-dimensional compressible fluid calculation was coupled with a finite- difference time-domain code and a particle-in-cell code with collision to reproduce propagation of electromagnetic wave, ionization process of plasma, and shock wave formation in atmospheric microwave discharge. Plasma filaments are driven toward the microwave source at 1 atm, and the distance between each filament is one-fifth of the wavelength of the incident microwave. The strong shock wave is generated due to the high plasma density at the atmospheric pressure. A simple analysis of the microwave propagation into the plasma shows that cut-off density of the microwave becomes smaller with the pressure decrease in a collisional plasma. At the lower pressure, the smaller density plasma is obtained with a diffusive pattern because of the smaller cut-off density and the larger diffusion effect. In contrast with the 1-atm case, the weak shock wave is generated at a rarefied condition, which lowers performance of microwave thruster.

  20. Conversion of natural gas to C2 hydrocarbons through dielectric-barrier discharge plasma catalysis

    Institute of Scientific and Technical Information of China (English)

    王保伟; 许根慧

    2002-01-01

    The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C2 hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H2/CH4, flow rate and catalyst on conversion of methane and selectivity of C2 hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C2 hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20-40 kV (8.4-40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20-60 mL@min?1. The conversion of methane can reach 45%, the selectivity of C2 hydrocarbons is 76%, and the total selectivity of C2 hydrocarbons and C3 hydrocarbons is nearly 100%. The conversion of methane increases with the increase of voltage and decreases with the flow of methane increase; the selectivity of C2 hydrocarbons decreases with the increase of voltage and increases with the flow of methane increase. The selectivity of C2 hydrocarbons is improved with catalyst for conversion of natural gas to C2 hydrocarbons in plasma field. Methane molecule collision with radicals is mainly responsible for product formation.

  1. Field demonstration and commercialization of silent discharge plasma hazardous air pollutant control technology

    Energy Technology Data Exchange (ETDEWEB)

    Rosocha, L.A.; Coogan, J.J.; Korzekwa, R.A.; Secker, D.A. [Los Alamos National Lab., NM (United States); Reimers, R.F.; Herrmann, P.G.; Chase, P.J.; Gross, M.P. [High Mesa Technologies LLC, Santa Fe, NM (United States)]|[High Mesa Technologies LLC, Irvine, CA (United States); Jones, M.R. [Electric Power Research Inst., Palo Alto, CA (United States)

    1996-07-01

    Silent electrical discharge plasma (dielectric barrier) reactors can decompose gas-phase pollutants by free-radical attack or electron-induced fragmentation. The radicals or electrons are produced by the large average volume nonthermal plasmas generated in the reactor. In the past decade, the barrier configuration has attracted attention for destroying toxic chemical agents for the military, removing harmful greenhouse gases, and treating other environmentally- hazardous chemical compounds. At the Los Alamos National Laboratory, we have been studying the silent discharge plasma (SDP) for processing gaseous-based hazardous chemicals for approximately five years. The key objective is to convert hazardous or toxic chemicals into non-hazardous compounds or into materials which are more easily managed. The main applications have been for treating off-gases from thermal treatment units, and for abating hazardous air-pollutant emissions (e.g., industrial air emissions, vapors extracted from contaminated soil or groundwater). In this paper, we will summarize the basic principles of SDP processing, discuss illustrative applications of the technology, and present results from small-scale field tests that are relevant to our commercialization effort.

  2. Spectroscopic studies of plasma in a carbon arc discharge for synthesis of nanomaterials

    Science.gov (United States)

    Vekselman, Vladislav; Feurer, Matthew; Yeh, Yao-Wen; Stratton, Brentley; Raitses, Yevgeny; LaboratoryPlasma Nanosynthesis Team

    2016-09-01

    An atmospheric pressure arc discharge with graphite electrodes is commonly used for synthesis of carbon nanomaterials such as buckyballs, nanotubes and graphene. In operation, the graphite anode ablates providing a feedstock material for synthesis these carbon nanostructures. Existing models predict that nucleation and growth of these nanomaterials in an arc discharge are governed by spatial distributions of density and temperature of plasma species. Control of these distributions can potentially enable optimization of nanosynthesis processes, to achieve the best combination of synthesis selectivity at the synthesis yield. In this work, we report first detail measurements of spatial distribution of arc plasma parameters obtained with a set of in-situ diagnostics, including optical emission spectroscopy and fast framing imaging. These parameters were measured in low- and high- anode ablation modes. Results of these measurements demonstrate a strong correlation between arc plasma and synthesis processes. This work was supported by U.S. Department of Energy, Office of Science, Basic Sciences, Materials Sciences and Engineering Division.

  3. Cylindrical dielectric barrier discharge plasma catalytic effect on chemical methods of silver nano-particle production

    Science.gov (United States)

    Bahrami, Zahra; Khani, Mohammad Reza; Shokri, Babak

    2016-11-01

    In this study, cylindrical dielectric barrier discharge plasma was used to study the catalytic effect on chemical methods of silver nano-particles for the first time. In this method, the processing time is short and the temperature of reaction is low. Also, the reactor is very simple, inexpensive, and accessible. In this work, pure AgNO3 as the precursor agent and poly vinyl pyrrolidone as the macromolecular surfactant were dissolved in ethanol as the solvent. UV-Vis and XRD were used to identify the colloidal and powder nano-particles, respectively. Optical emission spectroscopy was also used to identify the active species in plasma. Effects of gas flow rate, voltage, volume of solution, and processing time were also studied. Moreover, TEM and SEM images presented the mean diameter of nano-particle size around 10 to 20 nm. The results have been very promising.

  4. A secondary fuel removal process: plasma processing

    Energy Technology Data Exchange (ETDEWEB)

    Min, J. Y.; Kim, Y. S. [Hanyang Univ., Seoul (Korea, Republic of); Bae, K. K.; Yang, M. S. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-07-01

    Plasma etching process of UO{sub 2} by using fluorine containing gas plasma is studied as a secondary fuel removal process for DUPIC (Direct Use of PWR spent fuel Into Candu) process which is taken into consideration for potential future fuel cycle in Korea. CF{sub 4}/O{sub 2} gas mixture is chosen for reactant gas and the etching rates of UO{sub 2} by the gas plasma are investigated as functions of CF{sub 4}/O{sub 2} ratio, plasma power, substrate temperature, and plasma gas pressure. It is found that the optimum CF{sub 4}/O{sub 2} ratio is around 4:1 at all temperatures up to 400 deg C and the etching rate increases with increasing r.f. power and substrate temperature. Under 150W r.f. power the etching rate reaches 1100 monolayers/min at 400 deg C, which is equivalent to about 0.5mm/min. (author).

  5. INFLUENCE OF VACUUM ARC PLASMA EVAPORATOR CATHODE GEOMETRY OF ON VALUE OF ADMISSIBLE ARC DISCHARGE CURRENT

    Directory of Open Access Journals (Sweden)

    I. A. Ivanou

    2015-01-01

    Full Text Available An analysis of main design parameters that determine a level of droplet formation intensity at the generating stage of plasma flow has been given in the paper. The paper considers the most widely used designs of water cooled consumable cathodes. Ti or Ti–Si and Fe–Cr alloys have been taken as a material for cathodes. The following calculated data: average ionic charge Zi for titanium plasma +1.6; for «titanium–silicon plasma» +1.2, an electronic discharge 1.6022 ⋅ 10–19 C, an ion velocity vi = 2 ⋅ 104 m/s, an effective volt energy equivalent of heat flow diverted in the cathode Uк = 12 V, temperature of erosion cathode surface Тп = 550 К; temperature of the cooled cathode surface То = 350 К have been accepted in order to determine dependence of a maximum admissible arc discharge current on cathode height. The calculations have been carried out for various values of the cathode heights hк (from 0.02 to 0.05 m. Diameter of a target cathode is equal to 0.08 m for a majority of technological plasma devices, therefore, the area of the erosion surface is S = 0.005 m2.A thickness selection for a consumable target cathode part in the vacuum arc plasma source has been justified in the paper. The thickness ensures formation of minimum drop phase in the plasma flow during arc cathode material evaporation. It has been shown that a maximum admissible current of an arc discharge is practically equal to the minimum current of stable arcing when thickness of the consumable cathode part is equal to 0.05 m. The admissible discharge current can be rather significant and ensure high productivity during coating process with formation of relatively low amount of droplet phase in the coating at small values of hк.

  6. Measurement of Plasma Density Produced in Dielectric Barrier Discharge for Active Aerodynamic Control with Interferometer

    Institute of Scientific and Technical Information of China (English)

    LI Gang; ZHANG Yi; XU Yan-Ji; LIN Bin; LI Yu-Tong; ZHU Jun-Qiang

    2009-01-01

    We utilize an interferometer to investigate the changes of the refractive index caused by dielectric barrier discharge plasma.The electronic density of the plasma produced is measured and analyzed tentatively.The results show that density of the plasma increases linearly with exciting voltages.

  7. Investigation of Vortex Structures in Gas-Discharge Nonneutral Electron Plasma: I. Experimental Technique

    CERN Document Server

    Kervalishvili, N A

    2015-01-01

    The nonperturbing experimental methods have been described, by means of which the solitary vortex structures in gas-discharge nonneutral electron plasma were detected and investigated. The comparison with the experimental methods used in devices with pure electron plasma was made. The problems of shielding the electrostatic perturbations in nonneutral plasmas were considered.

  8. Reactivity of water vapor in an atmospheric argon flowing post-discharge plasma torch

    CERN Document Server

    Collette, S; Reniers, F

    2016-01-01

    The reactivity of water vapor introduced in the flowing post-discharge of an RF atmospheric plasma torch is investigated through electrical characterization, optical emission spectroscopy and mass spectrometry measurements. Due to the technical features of the plasma torch, the post-discharge can be considered as divided into two regions: an inner region (inside the plasma torch device) where the water vapor is injected and an outer region which directly interacts with the ambient air. The main reactions induced by the injection of water vapor are identified as well as those indicative of the influence of the ambient air. Plausible pathways allowing the production of H, OH, O radicals and H2O2 are discussed as well as reactions potentially responsible for inhomogeneities and for a low DC current measured in the flowing post-discharge. Keywords: atmospheric post-discharge, H2O plasma reactivity, RF plasma torch

  9. Numerical simulation of discharge plasma generation and nitriding the metals and alloys

    Science.gov (United States)

    Koval, T. V.; Manakov, R. A.; Nguyen Bao, Hung; Tran My, Kim An

    2017-01-01

    This research provides the numerical simulation of the plasma generation in a hollow cathode as well as the diffusion of nitrogen atoms into the metal in the low-pressure glow discharge plasma. The characteristics of the gas discharge were obtained and the relation of the basic technological parameters and the structural and phase state of the nitrided material were defined. Authors provided the comparison of calculations with the experimental results of titanium nitriding by low-pressure glow discharge plasma in a hollow cathode.

  10. Baking and helium glow discharge cleaning of SST-1 Tokamak with graphite plasma facing components

    Science.gov (United States)

    Semwal, P.; Khan, Z.; Raval, D. C.; Dhanani, K. R.; George, S.; Paravastu, Y.; Prakash, A.; Thankey, P.; Ramesh, G.; Khan, M. S.; Saikia, P.; Pradhan, S.

    2017-04-01

    Graphite plasma facing components (PFCs) were installed inside the SST-1 vacuum vessel. Prior to installation, all the graphite tiles were baked at 1000 °C in a vacuum furnace operated below 1.0 × 10-5 mbar. However due to the porous structure of graphite, they absorb a significant amount of water vapour from air during the installation process. Rapid desorption of this water vapour requires high temperature bake-out of the PFCs at ≥ 250 °C. In SST-1 the PFCs were baked at 250 °C using hot nitrogen gas facility to remove the absorbed water vapour. Also device with large graphite surface area has the disadvantage that a large quantity of hydrogen gets trapped inside it during plasma discharges which makes density control difficult. Helium glow discharge cleaning (He-GDC) effectively removes this stored hydrogen as well as other impurities like oxygen and hydrocarbon within few nano-meters from the surface by particle induced desorption. Before plasma operation in SST-1 tokamak, both baking of PFCs and He-GDC were carried out so that these impurities were removed effectively. The mean desorption yield of hydrogen was found to be 0.24. In this paper the results of baking and He-GDC experiments of SST-1 will be presented in detail.

  11. Evaluation of pulsed corona discharge plasma for the treatment of petroleum-contaminated soil.

    Science.gov (United States)

    Li, Rui; Liu, Yanan; Mu, Ruiwen; Cheng, Wenyan; Ognier, Stéphanie

    2017-01-01

    Petroleum hydrocarbons released to the environment caused by leakage or illegal dumping pose a threat to human health and the natural environment. In this study, the potential of a pulsed corona discharge plasma system for treating petroleum-polluted soils was evaluated. This system removed 76.93 % of the petroleum from the soil in 60 min with an energy efficiency of 0.20 mg/kJ. Furthermore, the energy and degradation efficiencies for the remediation of soil contaminated by single polyaromatic hydrocarbons, such as phenanthrene and pyrene, were also compared, and the results showed that this technology had potential in organic-polluted soil remediation. In addition, the role of water molecules was investigated for their direct involvement in the formation and transportation of active species. The increase of soil moisture to a certain extent clearly benefitted degradation efficiency. Then, treated soils were analyzed by FTIR and GC-MS for proposing the degradation mechanism of petroleum. During the plasma discharging processes, the change of functional group and the detection of small aromatic hydrocarbons indicated that the plasma active species attached petroleum hydrocarbons and degradation occurred. This technique reported herein demonstrated significant potential for the remediation of heavily petroleum-polluted soil, as well as for the treatment of organic-polluted soils.

  12. ULTRAVIOLET INDUCED MOTION OF A FLUORESCENT DUST CLOUD IN AN ARGON DIRECT CURRENT GLOW DISCHARGE PLASMA

    Energy Technology Data Exchange (ETDEWEB)

    Hvasta, M.G.; and Zwicker, A.

    2008-01-01

    Dusty plasmas consist of electrons, ions, neutrals and nm-μm sized particles commonly referred to as dust. In man-made plasmas this dust may represent impurities in a tokamak or plasma etching processing. In astrophysical plasmas this dust forms structures such as planetary rings and comet tails. To study dusty plasma dynamics an experiment was designed in which a 3:1 silica (<5 μm diameter) and fl uorescent dust mixture was added to an argon DC glow discharge plasma and exposed to UV radiation. This fl uorescent lighting technique offers an advantage over laser scattering (which only allows two-dimensional slices of the cloud to be observed) and is simpler than scanning mirror techniques or particle image velocimetry. Under typical parameters (P=150 mTorr, V anode= 100 V, Vcathode= -400 V, Itotal < 2mA) when the cloud is exposed to the UV light (100W, λ = 365 nm) the mixture fl uoresces, moves ~2mm towards the light source and begins rotating in a clockwise manner (as seen from the cathode). By calibrating a UV lamp and adjusting the relative intensity of the UV with a variable transformer it was found that both translational and rotational velocities are a function of UV intensity. Additionally, it was determined that bulk cloud rotation is not seen when the dust tray is not grounded while bulk translation is. This ongoing experiment represents a novel way to control contamination in man-made plasmas and a path to a better understanding of UV-bathed plasma systems in space..

  13. Wall ablation of heated compound-materials into non-equilibrium discharge plasmas

    Science.gov (United States)

    Wang, Weizong; Kong, Linghan; Geng, Jinyue; Wei, Fuzhi; Xia, Guangqing

    2017-02-01

    The discharge properties of the plasma bulk flow near the surface of heated compound-materials strongly affects the kinetic layer parameters modeled and manifested in the Knudsen layer. This paper extends the widely used two-layer kinetic ablation model to the ablation controlled non-equilibrium discharge due to the fact that the local thermodynamic equilibrium (LTE) approximation is often violated as a result of the interaction between the plasma and solid walls. Modifications to the governing set of equations, to account for this effect, are derived and presented by assuming that the temperature of the electrons deviates from that of the heavy particles. The ablation characteristics of one typical material, polytetrafluoroethylene (PTFE) are calculated with this improved model. The internal degrees of freedom as well as the average particle mass and specific heat ratio of the polyatomic vapor, which strongly depends on the temperature, pressure and plasma non-equilibrium degree and plays a crucial role in the accurate determination of the ablation behavior by this model, are also taken into account. Our assessment showed the significance of including such modifications related to the non-equilibrium effect in the study of vaporization of heated compound materials in ablation controlled arcs. Additionally, a two-temperature magneto-hydrodynamic (MHD) model accounting for the thermal non-equilibrium occurring near the wall surface is developed and applied into an ablation-dominated discharge for an electro-thermal chemical launch device. Special attention is paid to the interaction between the non-equilibrium plasma and the solid propellant surface. Both the mass exchange process caused by the wall ablation and plasma species deposition as well as the associated momentum and energy exchange processes are taken into account. A detailed comparison of the results of the non-equilibrium model with those of an equilibrium model is presented. The non-equilibrium results

  14. An advanced time-dependent collisional-radiative model of helium plasma discharges

    Science.gov (United States)

    Claustre, J.; Boukandou-Mombo, C.; Margot, J.; Matte, J.-P.; Vidal, F.

    2017-10-01

    A new spatially averaged time-dependent collisional-radiative model for helium plasmas, coupled to the electron Boltzmann equation (EBE), has been developed. Its main novelties are: (1) full time dependence for both the multi-species kinetics and the EBE. It is shown that this is necessary to correctly simulate discharges where the parameters vary on nanoseconds-microsecond timescales. (2) All electron processes are accounted for accurately. In particular, for the various ionization and recombination processes, free electrons are added or removed at the appropriate energy, with the appropriate interpolation on the energy grid. (3) The energy dependence of the electron loss by ambipolar diffusion is taken into account approximately. (4) All of the processes which are known to be important in helium discharges for pressure P≤slant 760 Torr are included, and 42 energy levels up to n = 6, where n is the main quantum number, are taken into account. Atomic and molecular ions, as well as excimers, are also included. (5) The gas temperature is calculated self-consistently. The model is validated through comparisons with known numerical steady-state results of Santos et al (2014 J. Phys. D. 47 265201) which they compared to their experimental results, and good agreement is obtained for their measured quantities. It is then applied to post-discharge decay cases with very short power decay times. The time evolution of the population densities and reaction rates are analyzed in detail with emphasis on the observed large increase of the metastable density.

  15. Ionized sputter deposition using an extremely high plasma density pulsed magnetron discharge

    Energy Technology Data Exchange (ETDEWEB)

    Macak, Karol [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Kouznetsov, Vladimir [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Schneider, Jochen [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Helmersson, Ulf [Department of Physics, Linkoeping University, SE-581 83 Linkoeping, (Sweden); Petrov, Ivan [Materials Science Department and Materials Research Laboratory, University of Illinois, Urbana, Illinois 61801 (United States)

    2000-07-01

    Time resolved plasma probe measurements of a novel high power density pulsed plasma discharge are presented. Extreme peak power densities in the pulse (on the order of several kW cm{sup -2}) result in a very dense plasma with substrate ionic flux densities of up to 1 A cm{sup -2} at source-to-substrate distances of several cm and at a pressure of 0.13 Pa (1 mTorr). The pulse duration was {approx}100 {mu}s with a pulse repetition frequency of 50 Hz. The plasma consists of metallic and inert gas ions, as determined from time resolved Langmuir probe measurements and in situ optical emission spectroscopy data. It was found that the plasma composition at the beginning of the pulse was dominated by Ar ions. As time elapsed metal ions were detected and finally dominated the ion composition. The effect of the process parameters on the temporal development of the ionic fluxes is discussed. The ionized portion of the sputtered metal flux was found to have an average velocity of 2500 m s{sup -1} at 6 cm distance from the source, which conforms to the collisional cascade sputtering theory. The degree of ionization of the sputtered metal flux at a pressure of 0.13 Pa was found to be 40%{+-}20% by comparing the total flux of deposited atoms with the charge measured for the metal ions in the pulse. (c) 2000 American Vacuum Society.

  16. Plasma detachment with molecular processes in divertor plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Ohno, N.; Ezumi, N.; Nishijima, D.; Takamura, S. [Dept. of Energy Engineering and Science, Graduate School of Engineering, Nagoya Univ., Nagoya, Aichi (Japan); Krasheninnikov, S.I.; Pigarov, A.Yu. [MIT Plasma Science and Fusion Center, Cambridge, MA (United States)

    2000-01-01

    Molecular processes in detached recombining plasmas are briefly reviewed. Several reactions with vibrationally excited hydrogen molecule related to recombination processes are described. Experimental evidence of molecular activated recombination observed in a linear divertor plasma simulator is also shown. (author)

  17. Catalytic-Dielectric Barrier Discharge Plasma Reactor For Methane and Carbon Dioxide Conversion

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2007-10-01

    Full Text Available A catalytic - DBD plasma reactor was designed and developed for co-generation of synthesis gas and C2+ hydrocarbons from methane. A hybrid Artificial Neural Network - Genetic Algorithm (ANN-GA was developed to model, simulate and optimize the reactor. Effects of CH4/CO2 feed ratio, total feed flow rate, discharge voltage and reactor wall temperature on the performance of catalytic DBD plasma reactor was explored. The Pareto optimal solutions and corresponding optimal operating parameters ranges based on multi-objectives can be suggested for catalytic DBD plasma reactor owing to two cases, i.e. simultaneous maximization of CH4 conversion and C2+ selectivity, and H2 selectivity and H2/CO ratio. It can be concluded that the hybrid catalytic DBD plasma reactor is potential for co-generation of synthesis gas and higher hydrocarbons from methane and carbon dioxide and showed better than the conventional fixed bed reactor with respect to CH4 conversion, C2+ yield and H2 selectivity for CO2 OCM process. © 2007 BCREC UNDIP. All rights reserved.[Presented at Symposium and Congress of MKICS 2007, 18-19 April 2007, Semarang, Indonesia][How to Cite: I. Istadi, N.A.S. Amin. (2007. Catalytic-Dielectric Barrier Discharge Plasma Reactor For Methane and Carbon Dioxide Conversion. Bulletin of Chemical Reaction Engineering and Catalysis, 2 (2-3: 37-44.  doi:10.9767/bcrec.2.2-3.8.37-44][How to Link/DOI: http://dx.doi.org/10.9767/bcrec.2.2-3.8.37-44 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/8][Cited by: Scopus 1 |

  18. Boosting persistence time of laser-induced plasma by electric arc discharge for optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Eschlböck-Fuchs, S., E-mail: simon.eschlboeck-fuchs@jku.at [Christian Doppler Laboratory for Laser-Assisted Diagnostics, Institute of Applied Physics, Johannes Kepler University Linz, A-4040 Linz (Austria); Kolmhofer, P.J.; Bodea, M.A.; Hechenberger, J.G.; Huber, N. [Christian Doppler Laboratory for Laser-Assisted Diagnostics, Institute of Applied Physics, Johannes Kepler University Linz, A-4040 Linz (Austria); Rössler, R. [voestalpine Stahl GmbH, A-4031 Linz (Austria); Pedarnig, J.D., E-mail: johannes.pedarnig@jku.at [Christian Doppler Laboratory for Laser-Assisted Diagnostics, Institute of Applied Physics, Johannes Kepler University Linz, A-4040 Linz (Austria)

    2015-07-01

    Plasma induced by nanosecond laser ablation is re-excited by a pulsed electric discharge and the parameters and optical emission of the plasma are measured. The discharge is a low-voltage and high-current electric arc that is triggered by the laser-induced plasma and slowly decaying with time. The optical emission of such combined plasma lasts up to several milliseconds which is much longer than without re-excitation (μs range). The emission spectra of re-excited plasma measured on different sample materials show higher line intensities than spectra measured by conventional laser-induced breakdown spectroscopy (LIBS). Moreover, emission lines of fluorine (spectral range 683–691 nm) and sulfur (range 520–550 nm) not detected by conventional LIBS become easily detectable with the combined plasma. The concentration of major components in metallurgical slags, as determined by calibration-free LIBS, agrees very well to the reference data evaluating the spectra taken from re-excited plasma. - Highlights: • Persistence time of laser-induced plasma in air is increased from ~ 10 μs to ~ 1 ms. • Laser-induced plasma triggers an electric arc discharge that boosts the plasma. • The combined laser-arc plasma is in LTE state over very long time (ms range). • CF-LIBS method delivers accurate results evaluating spectra of combined plasma. • Emission from S and F, not detected by LIBS, is detected with combined plasma.

  19. How does a probe inserted into the discharge influence the plasma structure?

    Science.gov (United States)

    Yordanov, D.; Lishev, St.; Shivarova, A.

    2016-05-01

    Shielding the bias applied to the probe by the sheath formed around it and determination of parameters of unperturbed plasmas are in the basis of the probe diagnostics. The results from a two-dimensional model of a discharge with a probe inserted in it show that the probe influences the spatial distribution of the plasma parameters in the entire discharge. The increase (although slight) in the electron temperature, due to the increased losses of charged particles on the additional wall in the discharge (mainly the probe holder), leads to redistribution of the plasma density and plasma potential, as shown by the results obtained at the floating potential of the probe. The deviations due to the bias applied to the probe tip are stronger in the ion saturation region of the probe characteristics. The pattern of the spatial redistribution of the plasma parameters advances together with the movement of the probe deeper in the discharge. Although probe sheaths and probe characteristics resulting from the model are shown, the study does not aim at discussions on the theories for determination of the plasma density from the ion saturation current. Regardless of the modifications in the plasma behavior in the entire discharge, the deviations of the plasma parameters at the position of the probe tip and, respectively, the uncertainty which should be added as an error when the accuracy of the probe diagnostics is estimated do not exceed 10%. Consequently, the electron density and temperature obtained, respectively, at the position of the plasma potential on the probe characteristics and from its transition region are in reasonable agreement with the results from the model of the discharge without a probe. Being in the scope of research on a source of negative hydrogen ions with the design of a matrix of small radius inductive discharges, the model is specified for a low-pressure hydrogen discharge sustained in a small-radius tube.

  20. Developing Process of Negative Creeping Discharge along Aerial Insulated Wire

    Science.gov (United States)

    Nishi, Toshiyuki; Hanaoka, Ryoichi; Takata, Shinzo

    When a lightning occurs at the neighborhood of high voltage aerial distribution lines, the overvoltage due to the inductive lightning surge invades to the central line of the insulated wire. Because of the insulated wire is supported by the insulator and the binding wire at the electric light pole, the creeping discharges develop along the wire surface from the free end of the binding wire, just after a flashover of the insulator at the wire supporting point. These creeping discharges give rise to the disaster near the wire supporting point including the punch-through breakdown of wire when the weak points such as pin-holes exist in the wire insulator. To prevent these accidents, it is important to understand the behavior of creeping discharges at the insulated wire surface originating in the lightning strike. Positive and negative creeping discharges reveal the distinctive aspect by the polarities of the inductive lightning surges. In the previous paper, we have clarified the developing process of positive creeping discharge based on the data obtained from an image converter camera. In this paper, we report the developing process of negative creeping discharge. Complicated behavior of negative creeping discharge is clarified using an image converter camera and its process is discussed.

  1. Dusty plasma in a glow discharge in helium in temperature range of 5–300 K

    Energy Technology Data Exchange (ETDEWEB)

    Samoilov, I. S.; Baev, V. P.; Timofeev, A. V., E-mail: timofeevalvl@gmail.com; Amirov, R. Kh.; Kirillin, A. V.; Nikolaev, V. S.; Bedran, Z. V. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation)

    2017-03-15

    Dusty plasma structures in glow discharge in helium in the temperature range of 5–300 K are investigated experimentally. We have described the experimental setup that makes it possible to continuously vary the temperature regime. The method for experimental data processing has been described. We have measured interparticle distances in the temperature range of 9–295 K and compared them with the Debye radius. We indicate the ranges of variations in experimental parameters in which plasma–dust structures are formed and various types of their behavior are manifested (rotation, vibrations of structures, formation of vertical linear chains, etc.). The applicability of the Yukawa potential to the description of the structural properties of a dusty plasma in the experimental conditions is discussed.

  2. Degradation of Anionic Dye Eosin by Glow Discharge Electrolysis Plasma

    Institute of Scientific and Technical Information of China (English)

    GAO Jinzhang; MA Dongping; GUO Xiao; WANG Aixiang; FU Yan; WU Jianlin; YANG Wu

    2008-01-01

    This paper describes a novel method for the degradation of eosin by using glow discharge electrolysis (GDE). The effects of various parameters on the removal efficiency were studied. It was found that the eosin degradation could be raised considerably by increasing the applied voltage and the initial concentration, or by decreasing pH of the aqueous solution. Fe2+ ion had an evident accelerating effect on the eosin degradation. The degradation process of eosin obeyed a pseudo-first-order reaction. The relationship between the degradation rate constant κ and the reaction temperature T could be expressed by Arrhenius equation with which the apparent activation energy Ea of 14.110 kJ. Mol-1 and the pre-exponential factor k0 of 2.065×10-1 min-1 were obtained, too. The determination of hydroxyl radical was carried out by using N, N-dimethyl -p-nitrosoaniline (RNO) as a scavenger. The results showed that the hydroxyl radical plays an important role in the degradation process.

  3. Electron density measurement in gas discharge plasmas by optical and acoustic methods

    Science.gov (United States)

    Biagioni, A.; Anania, M. P.; Bellaveglia, M.; Chiadroni, E.; Cianchi, A.; Di Giovenale, D.; Di Pirro, G.; Ferrario, M.; Filippi, F.; Mostacci, A.; Pompili, R.; Shpakov, V.; Vaccarezza, C.; Villa, F.; Zigler, A.

    2016-08-01

    Plasma density represents a very important parameter for both laser wakefield and plasma wakefield acceleration, which use a gas-filled capillary plasma source. Several techniques can be used to measure the plasma density within a capillary discharge, which are mainly based on optical diagnostic methods, as for example the well-known spectroscopic method using the Stark broadening effect. In this work, we introduce a preliminary study on an alternative way to detect the plasma density, based on the shock waves produced by gas discharge in a capillary. Firstly, the measurements of the acoustic spectral content relative to the laser-induced plasmas by a solid target allowed us to understand the main properties of the acoustic waves produced during this kind of plasma generation; afterwards, we have extended such acoustic technique to the capillary plasma source in order to calibrate it by comparison with the stark broadening method.

  4. Real time control of long duration plasma discharges in Tore Supra

    Energy Technology Data Exchange (ETDEWEB)

    Saint-Laurent, F.; Bucalossi, J.; Buravand, Y.; Chatelier, E.; Guillerminet, B.; Leroux, F.; Martin, G.; Moulin, D.; Spuig, P.; Van Houtte, D

    2003-07-01

    The in-vessel components and water cooling loops were fully renewed in order to permit Tore-Supra to explore the route of long duration plasma discharges. This renovation has implied important upgrades of both the data acquisition system (DAS) and the plasma control system. This paper is dedicated to these 2 upgrades. The new DAS design allows: -) a continuous data acquisition, -) high data flow rate management (the flow rate can reach 18 MB/s per front-end unit), -) continuous data access and processing, and -) real-time data processing. The upgrade of the plasma control system implies to share information at a real time level. This system is supported by the SCRAMNet network that has proved its flexibility (continuous addition of nodes), and its robustness (no network failure during 7 years of operation). The possibility to share VME units as well as PC units enable us to strongly increase the available real-time CPU power. The development of advanced real-time plasma control algorithms becomes thus accessible. The real-time equilibrium reconstruction is a first example of such a generation of algorithms. (A.C.)

  5. Dielectric material degradation monitoring of dielectric barrier discharge plasma actuators

    Science.gov (United States)

    Hanson, Ronald E.; Houser, Nicole M.; Lavoie, Philippe

    2014-01-01

    It is a known phenomenon that some dielectric materials used to construct plasma actuators degrade during operation. However, the rate at which this process occurs, to what extent, as well as a method to monitor is yet to be established. In this experimental study, it is shown that electrical measurements can be used to monitor changes in the material of the plasma actuators. The procedure we introduce for monitoring the actuators follows from the work of Kriegseis, Grundmann, and Tropea [Kriegseis et al., J. Appl. Phys. 110, 013305 (2011)], who used Lissajous figures to measure actuator power consumption and capacitance. In the present study, we quantify changes in both the power consumption and capacitance of the actuators over long operating durations. It is shown that the increase in the effective capacitance of the actuator is related to degradation (thinning) of the dielectric layer, which is accompanied by an increase in actuator power consumption. For actuators constructed from layers of Kapton® polyimide tape, these changes are self-limiting. Although the polyimide film degrades relatively quickly, the underlying adhesive layer appears to remain intact. Over time, the effective capacitance was found to increase by up to 36%, 25%, and 11% for actuators constructed with 2, 3, and 4 layers of Kapton tape, respectively. A method is presented to prevent erosion of the Kapton dielectric layer using a coating of Polydimethylsiloxane oil. It is shown the application of this treatment can delay the onset of degradation of the Kapton dielectric material.

  6. Micronucleus formation induced by dielectric barrier discharge plasma exposure in brain cancer cells

    Science.gov (United States)

    Kaushik, Nagendra K.; Uhm, Hansup; Ha Choi, Eun

    2012-02-01

    Induction of micronucleus formation (cytogenetic damage) in brain cancer cells upon exposure of dielectric barrier discharge plasma has been investigated. We have investigated the influence of exposure and incubation times on T98G brain cancer cells by using growth kinetic, clonogenic, and micronucleus formation assay. We found that micronucleus formation rate directly depends on the plasma exposure time. It is also shown that colony formation capacity of cells has been inhibited by the treatment of plasma at all doses. Cell death and micronucleus formation are shown to be significantly elevated by 120 and 240 s exposure of dielectric barrier discharge plasma.

  7. Characterization of a copper spark discharge plasma in argon atmosphere used for nanoparticle generation

    Science.gov (United States)

    Kohut, Attila; Galbács, Gábor; Márton, Zsuzsanna; Geretovszky, Zsolt

    2017-04-01

    Spark discharge nanoparticle generation is a dynamically developing application of discharge plasmas. In the present study a spark plasma used for nanoparticle generation is characterized by means of spatially and temporally resolved optical emission spectroscopy (OES) supplemented by fast imaging. The data acquired during the generation of copper nanoparticles in argon ambient is used to describe the spatial and temporal evolution of the species in the spark gap and to derive plasma parameters such as excitation temperature and electron concentration on one hand, and the concentration of the Cu species eroded by a single spark on the other. It is shown that temporally and spatially resolved OES together with a simple equilibrium model are efficient tools to estimate the characteristics of the spark discharge plasma that typically exists in spark discharge nanoparticle generators.

  8. Simulation Tool for Dielectric Barrier Discharge Plasma Actuators at Atmospheric and Sub-Atmospheric Pressures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Traditional approaches for active flow separation control using dielectric barrier discharge (DBD) plasma actuators are limited to relatively low-speed flows and...

  9. Simulation Tool for Dielectric Barrier Discharge Plasma Actuators at Atmospheric and Sub-Atmospheric Pressures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Traditional approaches for active flow separation control using dielectric barrier discharge (DBD) plasma actuators are limited to relatively low-speed flows and...

  10. Versatile particle collection concept for correlation of particle growth and discharge parameters in dusty plasmas

    Science.gov (United States)

    Hinz, A. M.; von Wahl, E.; Faupel, F.; Strunskus, T.; Kersten, H.

    2015-02-01

    The feasibility of collecting nanoparticles from a dusty plasma by means of the neutral drag force is investigated. The nanoparticles are formed in a capacitively coupled asymmetric discharge running in an Ar/C2H2—mixture at a frequency of 13.56 MHz and an RF-power of 9 W. By opening a gate valve between the plasma reactor and a vacuum chamber at a lower pressure at any desired point of the growth cycle of the dust particles a neutral gas flux is induced that drags the particles out of the plasma onto a substrate. By changing the parameters of the collection process, e.g. the substrate positioning or the substrate temperature, the efficiency of the collection process can be adjusted. Information about the particle size distributions is obtained by performing ex situ SEM measurements. As the collection process creates a time stamp in the in situ recorded control parameters, e.g. the self-bias voltage or the process gas pressure, a direct and precise correlation between the control parameters and the particle size distribution is obtained.

  11. Characteristics of cold atmospheric plasma source based on low-current pulsed discharge with coaxial electrodes

    Science.gov (United States)

    Bureyev, O. A.; Surkov, Yu S.; Spirina, A. V.

    2017-05-01

    This work investigates the characteristics of the gas discharge system used to create an atmospheric pressure plasma flow. The plasma jet design with a cylindrical graphite cathode and an anode rod located on the axis of the system allows to realize regularly reproducible spark breakdowns mode with a frequency ∼ 5 kHz and a duration ∼ 40 μs. The device generates a cold atmospheric plasma flame with 1 cm in diameter in the flow of various plasma forming gases including nitrogen and air at about 100 mA average discharge current. In the described construction the cathode spots of individual spark channels randomly move along the inner surface of the graphite electrode creating the secondary plasma stream time-average distributed throughout the whole exit aperture area after the decay of numerous filamentary discharge channels. The results of the spectral diagnostics of plasma in the discharge gap and in the stream coming out of the source are presented. Despite the low temperature of atoms and molecules in plasma stream the cathode spots operation with temperature of ∼ 4000 °C at a graphite electrode inside a discharge system enables to saturate the plasma by CN-radicals and atomic carbon in the case of using nitrogen as the working gas.

  12. Effect of Discharge Voltage on an Ion Sheath Formed at a Grid in a Multi-Dipole Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    M.K.Mishra; A.Phukan

    2008-01-01

    @@ It is experimentally demonstrated that a relatively strong ion-rich sheath formed at a fixed negative bias of the grid can be changed to arather weak ion sheath(sheath potential weakly retards dectrons)only by increasing the discharge voltage in the system.At sufficiently high negative grid bias,an increase of discharge voltage enhances the ion collection current at the grid.An explanation is put forward in support of this experimental observation.A slight density enhancement with a fall in plasma electron temperature is also observed with the increasing negative grid bias.

  13. Characteristics and plasma parameters of a short-wavelength low-pressure discharge lamp

    Science.gov (United States)

    Shuaibov, A. K.; Shevera, I. V.; Malinina, A. A.

    2008-10-01

    We have studied the working optical characteristics and electron kinetic coefficients of a short-wavelength, electric discharge exciplex-halogen UV-VUV lamp employing a mixture of argon and chlorine with a total pressure of P = 0.5 10 kPa. The lamp operates on a system of broadened electron-vibrational bands of ArCl (175 nm) and chlorine (200, 258 nm) molecules, which overlap to form a continuum in the spectral range of 160 260 nm. It is established that the optimum mixtures are those with p(Ar) - p(Cl2) = (2 4)-(0.15 0.30) kPa. The average output power of the short-wavelength radiation is 1 2 W at an efficiency of ˜5%. The electron energy distribution functions (EDFs) and the discharge plasma parameters have been calculated by solving the Boltzmann equation for a gas mixture with the experimentally determined optimum composition in the range of E/ P values from 1 to 200 V/(cm Torr), where E is the electric field strength and P is the total gas pressure. Using the obtained EDFs, the electron transport characteristics, specific discharge power losses for the main elementary processes, and rate constants of electron processes are determined.

  14. [Investigation on the Spectral Characteristics of a Plasma Jet in Atmospheric Argon Glow Discharge].

    Science.gov (United States)

    Li, Xue-chen; Zhang, Chun-yan; Li, Ji-yuan; Bao, Wen-ting

    2015-12-01

    Plasma jet is a kind of important plasma source at atmospheric pressure. In recent years, it becomes an important hot topic in the field of low temperature plasma. In this paper, using a tungsten needle and a tungsten wire mesh, a direct-current excited jet is developed to operate in argon at atmospheric pressure. In the atmospheric pressure argon, the plasma jet can produce a stable plasma plume. By using the method of emission spectroscopy, the parameters of the plasma plume are investigated. The discharge emits dazzling white light from the area between the tungsten needle electrode and the wire mesh electrode. A plasma plume with a flame shape appears outside the tungsten wire mesh electrode. For a constant value of voltage (U = 13.5 kV), the length of the plasma plume increases with the gas flow rate. For a constant value of the gas flow rate(10 L · min⁻¹), the length of the plasma plume increases with the voltage. The voltage is inversely proportional to the current under the constant gas flow rate. In other words, the voltage decreases with the discharge current, which indicates that a glow discharge is formed in the plasma jet. Optical emission spectrum in 300 to 800 nm is collected from the direct-current excited plasma jet. By Boltzmann plot method, the excited electron temperature of the plasma plume is investigated as a function of the applied voltage or the gas flow rate. Results show that the excited electron temperature increases with decreasing applied voltage under the constant gas flow. Moreover, it increases with decreasing the gas flow under the constant voltage. Based on the discharge theory, these experimental phenomena are explained qualitatively. These results are of great importance to the development of atmospheric pressure uniform discharge plasma source and its application in industrial field.

  15. Observation of Quartz Cathode-Luminescence in a Low Pressure Plasma Discharge

    Science.gov (United States)

    Foster, John E.

    2004-01-01

    Intense, steady-state cathode-luminescence has been observed from exposure of quartz powder to a low pressure rf-excited argon plasma discharge. The emission spectra (400 to 850 nm) associated with the powder luminescence were documented as a function of bias voltage using a spectrometer. The emission was broad-band, essentially washing out the line spectra features of the argon plasma discharge.

  16. Parameters of the plasma of a dc pulsating discharge in a supersonic air flow

    Energy Technology Data Exchange (ETDEWEB)

    Shibkov, V. M., E-mail: shibkov@phys.msu.ru; Shibkova, L. V.; Logunov, A. A. [Moscow State University, Faculty of Physics (Russian Federation)

    2017-03-15

    A dc discharge in a cold (T = 200 K) supersonic air flow at a static pressure of 200–400 Torr was studied experimentally. The excited unsteady pulsating discharge has the form of a thin plasma channel with a diameter of ≤1 mm, stretched downstream the flow. Depending on the discharge current, the pulsation frequency varies from 800 to 1600 Hz and the electron temperature varies from 8000 to 15000 K.

  17. A Review on Chemical Effects in Aqueous Solution induced by Plasma with Glow Discharge

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Chemical effects in different aqueous solutions induced by plasma with glow dis charge electrolysis (GDE) and contact glow discharge electrolysis (CGDE) are described in this paper. The experimental and discharge characteristics are also reviewed. These are followed by a discussion of their mechanisms of both anodic and cathodic CGDE..

  18. Kinetic temperature of dust particle motion in gas-discharge plasma

    NARCIS (Netherlands)

    Norman, G. E.; Timofeev, A. V.

    2011-01-01

    A system of equations describing motion of dust particles in gas discharge plasma is formulated. This system is developed for a monolayer of dust particles with an account of dust particle charge fluctuations and features of the discharge near-electrode layer. Molecular dynamics simulation of the du

  19. Role of on-board discharge in shock wave drag reduction and plasma cloaking

    Institute of Scientific and Technical Information of China (English)

    Qiu Xiao-Ming; Tang De-Li; Sun Ai-Ping; Liu Wan-Dong; Zeng Xue-Jun

    2007-01-01

    In the present paper, a physical model is proposed for reducing the problem of the drag reduction of an attached bow shock around the nose of a high-speed vehicle with on-board discharge, to the problem of a balance between the magnetic pressure and gas pressure of plane shock of a partially ionized gas consisting of the environmental gas around the nose of the vehicle and the on-board discharge-produced plasma. The relation between the shock strength and the discharge-induced magnetic pressure is studied by means of a set of one-fluid, hydromagnetic equations reformed for the present purpose, where the discharge-induced magnetic field consists of the electron current (produced by the discharge)-induced magnetic field and the partially ionized gas flow-induced one. A formula for the relation between the above parameters is derived. It shows that the discharge-induced magnetic pressure can minimize the shock strength,successfully explaining the two recent experimental observations on attached bow shock mitigation and elimination in a supersonic flow during on-board discharge [Phys. Plasmas 9 (2002) 721 and Phys. Plasmas 7 (2000) 1345]. In addition,the formula implies that the shock elimination leaves room for a layer of higher-density plasma rampart moving around the nose of the vehicle, being favourable to the plasma radar cloaking of the vehicle. The reason for it is expounded.

  20. Investigation of Vortex Structures in Gas-Discharge Nonneutral Electron Plasma: II. Vortex Formation, Evolution and Dynamics

    CERN Document Server

    Kervalishvili, N A

    2015-01-01

    The results of experimental investigations of inhomogeneities of gas-discharge nonneutral electron plasma obtained by using the nonperturbing experimental methods [N.A. Kervalishvili, arXiv:1502.02516 [physics.plasm-ph] (2015)] have been presented. Inhomogeneities are the dense solitary vortex structures stretched along the magnetic field, the lifetime of which is much greater than the time of electron-neutral collisions. The processes of formation, evolution and dynamics of vortex structures were studied. The periodic sequence of these processes is described for different geometries of discharge device.

  1. Plasma diagnostics in plasma processing for nanotechnology and nanolevel chemistry

    Directory of Open Access Journals (Sweden)

    Hiroshi Akatsuka

    2004-01-01

    Full Text Available The author reviews the role of various plasma diagnostics in plasma processing for nanotechnology, and points out some essential methods of spectroscopic methods to diagnose plasmas for nanoprocessing. Two experimental examples are discussed between the characteristics of nanomaterials and plasma parameters. One is measurement of rotation temperature in processing of carbon nanotube. The other is that of vibrational temperature in surface nitriding of titanium by nitrogen plasma processing. We summarize what to measure and how to measure them from the technical viewpoint of plasma diagnostics.

  2. Sporicidal properties from surface micro-discharge plasma under different plasma conditions at different humidities

    Science.gov (United States)

    Jeon, J.; Klaempfl, T. G.; Zimmermann, J. L.; Morfill, G. E.; Shimizu, T.

    2014-10-01

    In the current study, bacterial endospores of Geobacillus stearothermophilus are exposed to the surface micro-discharge plasma for 5 min and the humidity and power consumption are varied. At the low humidity of 5.5 ± 0.5 g m-3, almost no sporicidal effect (<0.5 log) is observed. At the high humidity of 17.9 ± 0.6 g m-3, the spore reduction increases monotonically up to 3.5 log with increasing power consumption. At a humidity of 10.4 ± 0.6 g m-3, the spores are inactivated in a limited range of power consumption with a maximum reduction of ˜2.5 log. The survival curves show a single-slope decrease of the spores. The contribution of heat and UV to the sporicidal effect as well as the inactivation of spores by the short-lived species from the plasma are ruled out. The concentration of ozone, one indicator for the long-lived species, is measured and no correlation with the sporicidal effect is found. In conclusion, water-related reactive species, e.g. hydrogen peroxide, appear to be responsible for the sporicidal effect under the investigated conditions. Furthermore, condensation of water at high humidity enables the plasma-activated water containing both long-lived and short-lived reactive species to contribute to the sporicidal effect.

  3. Investigation of dielectric barrier discharge plasma flow control

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Effects of plasma flow control are researched on the basis of plasma exciting flow experiments and numerical simulations. Turbulent model is more effective than laminar model in plasma numerical simulation as results showed. Both plasma exciting effects of acceleration and flow separation suppression are investigated through experiments carried on the flat plate and the compressor cascades. The results demonstrate that boundary layer characteristic is modified by plasma exciting. Distributions of total pressure and velocity in the wake are improved notably for 20 m/s coming velocity and the effect of plasma can still be observed while velocity is increased to 50 m/s. For low velocity flow, plasma exciting is effective in flow separation suppression.

  4. Effect of Electron Energy Distribution on the Hysteresis of Plasma Discharge: Theory, Experiment, and Modeling.

    Science.gov (United States)

    Lee, Hyo-Chang; Chung, Chin-Wook

    2015-10-20

    Hysteresis, which is the history dependence of physical systems, is one of the most important topics in physics. Interestingly, bi-stability of plasma with a huge hysteresis loop has been observed in inductive plasma discharges. Despite long plasma research, how this plasma hysteresis occurs remains an unresolved question in plasma physics. Here, we report theory, experiment, and modeling of the hysteresis. It was found experimentally and theoretically that evolution of the electron energy distribution (EED) makes a strong plasma hysteresis. In Ramsauer and non-Ramsauer gas experiments, it was revealed that the plasma hysteresis is observed only at high pressure Ramsauer gas where the EED deviates considerably from a Maxwellian shape. This hysteresis was presented in the plasma balance model where the EED is considered. Because electrons in plasmas are usually not in a thermal equilibrium, this EED-effect can be regarded as a universal phenomenon in plasma physics.

  5. Parallel 3-D numerical simulation of dielectric barrier discharge plasma actuators

    Science.gov (United States)

    Houba, Tomas

    Dielectric barrier discharge plasma actuators have shown promise in a range of applications including flow control, sterilization and ozone generation. Developing numerical models of plasma actuators is of great importance, because a high-fidelity parallel numerical model allows new design configurations to be tested rapidly. Additionally, it provides a better understanding of the plasma actuator physics which is useful for further innovation. The physics of plasma actuators is studied numerically. A loosely coupled approach is utilized for the coupling of the plasma to the neutral fluid. The state of the art in numerical plasma modeling is advanced by the development of a parallel, three-dimensional, first-principles model with detailed air chemistry. The model incorporates 7 charged species and 18 reactions, along with a solution of the electron energy equation. To the author's knowledge, a parallel three-dimensional model of a gas discharge with a detailed air chemistry model and the solution of electron energy is unique. Three representative geometries are studied using the gas discharge model. The discharge of gas between two parallel electrodes is used to validate the air chemistry model developed for the gas discharge code. The gas discharge model is then applied to the discharge produced by placing a dc powered wire and grounded plate electrodes in a channel. Finally, a three-dimensional simulation of gas discharge produced by electrodes placed inside a riblet is carried out. The body force calculated with the gas discharge model is loosely coupled with a fluid model to predict the induced flow inside the riblet.

  6. Simulations of low field helicon discharges using a two-dimensional hybrid plasma equipment model

    Energy Technology Data Exchange (ETDEWEB)

    Kinder, R.L.; Kushner, M.J.

    1999-07-01

    As the semiconductor industry moves towards larger wafers, a greater degree of process uniformity than is currently available with conventional inductively coupled plasma reactors will be necessary. Due to their high ionization efficiency, high flux density and their ability to deposit power within the volume of the plasma, helicon reactors are being developed for downstream etching and deposition. The power coupling of the antenna radiation to the plasma is of concern due to issues related to process uniformity. Furthermore, operation of helicon discharges at low magnetic fields (5--20 G) is not only economically attractive, but lower fields provide greater ion flux uniformity to the substrate. At low magnetic fields, it has been observed that there is a resonant peak in the power deposition and plasma density. This has been attributed to the occurrence of an electron cyclotron wave, or Trivelpiece-Gould (TG) mode, when {omega}/{omega}{sub c} is of order unity. To investigate these issues, the authors have improved the electromagnetics module of the HPEM to resolve the helicon wave structure of a m = 0 mode. The electrostatic component of the wave equation has been neglected, so this work focuses on the effects of the helicon mode. Plasma dynamics are coupled to the electromagnetic fields through a tensor form of Ohm's law and an effective collision frequency for Landau damping has been incorporated. Using a solenoidal magnetic field and an antenna operating at 13.65 MHz, studies show a shift in the power deposition towards the center of the reactor as the magnetic field is decreased below 30 G. Furthermore, peak values and wave structure is sensitive to the magnetic field configuration. Results for process relevant gas mixtures are examined and the dependence on magnetic field strength, field configuration and power are discussed.

  7. Changes in Properties of Dielectric Barrier Discharge Plasma Jets for Different Gases and for Insulating and Conducting Transfer Plates

    Science.gov (United States)

    do Nascimento, Fellype; Moshkalev, Stanislav; Machida, Munemasa

    2017-03-01

    Dielectric barrier discharge (DBD) plasma jets have been studied extensively in recent years because of its wide range of applications. DBD plasmas can be produced using many different gases and can be applied to a broad variety of surfaces and substrates. This work provides comparisons of DBD plasmas generated using argon (Ar), helium (He), and nitrogen (N2), as well as their mixtures with water vapor in order to know how some plasma properties are affected by the use of different gases. All plasmas were studied in two different conditions: using a transfer plate made of a conductive material and using a transfer plate made of an insulating one. It was observed that the process of Penning ionization of nitrogen molecules by direct collisions with metastable atoms and molecules is evident and significant only in plasmas that use He as the working gas, which means that He atoms in metastable states have greater ability to transfer energy to molecules of nitrogen in the plasma. The collisions of metastable He with N2 molecules determine the vibrational temperature (T vib) values in He plasmas, while in Ar and N2 plasmas, the T vib values are determined mainly by collisions of electrons with N2 molecules. It was noticed that the use of an insulating or a conducting transfer plate as the sample holder affects the results of adhesion between poly(dimethylsiloxane) samples, and it is mainly due to the differences in the plasma power, with a higher plasma power leading to better adhesion.

  8. Rydberg gas theory of a glow discharge plasma: I. Application to the electrical behaviour of a fast flowing glow discharge plasma.

    Science.gov (United States)

    Mason, Rod S; Mitchell, David J; Dickinson, Paul M

    2010-04-21

    Current-voltage (I-V) curves have been measured, independent of the main discharge, for electricity passing through the steady state fast flowing 'afterglow' plasma of a low power dc glow discharge in Ar. Voltage profiles along the axial line of conduction have been mapped using fixed probes and potentiometry, and the mass spectra of cations emerging from the downstream sampling Cone, also acting as a probe anode, were recorded simultaneously. Floating double probe experiments were also carried out. The electrical behavior is consistent with the well established I-V characteristics of such discharges, but does not comply with classical plasma theory predictions. The plasma decays along the line of conduction, with a lifetime of approximately 1 ms, despite carrying a steady state current, and its potential is below that of the large surface area anode voltage; a situation which cannot exist in the presence of a conventional free ion-electron plasma, unless the electron temperature is super cold. Currents, large by comparison with the main discharge current, and independent of it, are induced to flow through the downstream plasma, from the Anode (acting as a cathode) to the anodic ion exit Cone, induced by electron impact ionisation at the anode, but without necessarily increasing the plasma density. It appears to be conducted by direct charge transfer between a part of the anode surface (acting as cathode to the auxiliary circuit) and the plasma, without secondary electron emission or heating, which suggests the direct involvement of Rydberg atom intermediates. The reaction energy defect (= the work function of the electrode surface) fits with the plasma potential threshold observed for the cathodic reaction to occur. A true free ion-electron plasma is readily detected by the observation of cations at the anode surface, when induced at the downstream anode, at high bias voltages, by the electron impact ionisation in the boundary region. In contrast to the classical

  9. Physics of Collisional Plasmas Introduction to High-Frequency Discharges

    CERN Document Server

    Moisan, Michel

    2012-01-01

    The Physics of Collisional Plasmas deals with the plasma physics of interest to laboratory research and industrial applications, such as lighting, fabrication of microelectronics, destruction of greenhouse gases. Its emphasis is on explaining the physical mechanisms, rather than the detailed mathematical description and theoretical analysis. At the introductory level, it is important to convey the characteristic physical phenomena of plasmas, before addressing the ultimate formalism of kinetic theory, with its microscopic, statistical mechanics approach. To this aim, this text translates the physical phenomena into more tractable equations, using the hydrodynamic model; this considers the plasma as a fluid, in which the macroscopic physical parameters are the statistical averages of the microscopic (individual) parameters. This book is an introduction to the physics of collisional plasmas, as opposed to plasmas in space. It is intended for graduate students in physics and engineering . The first chapter intr...

  10. The effect of substrate holder size on the electric field and discharge plasma on diamond-film formation at high deposition rates during MPCVD

    Science.gov (United States)

    An, Kang; Chen, Liangxian; Liu, Jinlong; Zhao, Yun; Yan, Xiongbo; Hua, Chenyi; Guo, Jianchao; Wei, Junjun; Hei, Lifu; Li, Chengming; Lu, Fanxiu

    2017-09-01

    The effect of the substrate holder feature dimensions on plasma density (n e), power density (Q mw) and gas temperature (T) of a discharge marginal plasma (a plasma caused by marginal discharge) and homogeneous plasma were investigated for the microwave plasma chemical vapor deposition process. Our simulations show that decreasing the dimensions of the substrate holder in a radical direction and increasing its dimension in the direction of the axis helps to produce marginally inhomogeneous plasma. When the marginal discharge appears, the maximum plasma density and power density appear at the edge of the substrate. The gas temperature increases until a marginally inhomogeneous plasma develops. The marginally inhomogeneous plasma can be avoided using a movable substrate holder that can tune the plasma density, power density and gas temperature. It can also ensure that the power density and electron density are as high as possible with uniform distribution of plasma. Moreover, both inhomogeneous and homogeneous diamond films were prepared using a new substrate holder with a diameter of 30 mm. The observation of inhomogeneous diamond films indicates that the marginal discharge can limit the deposition rate in the central part of the diamond film. The successfully produced homogeneous diamond films show that by using a substrate holder it is possible to deposit diamond film at 7.2 μm h-1 at 2.5 kW microwave power.

  11. Glyphosate contaminated soil remediation by atmospheric pressure dielectric barrier discharge plasma and its residual toxicity evaluation.

    Science.gov (United States)

    Wang, Tiecheng; Ren, Jingyu; Qu, Guangzhou; Liang, Dongli; Hu, Shibin

    2016-12-15

    Glyphosate was one of the most widely used herbicides in the world. Remediation of glyphosate-contaminated soil was conducted using atmospheric pressure dielectric barrier discharge (DBD) plasma. The feasibility of glyphosate degradation in soil was explored, and the soil leachate toxicity after remediation was assessed via a seed germination test. The experimental results showed that approximately 93.9% of glyphosate was degraded within 45min of DBD plasma treatment with an energy yield of 0.47gkWh(-1), and the degradation process fitted the first-order kinetic model. Increasing the discharge voltage and decreasing the organic matter content of the soil were both found to facilitate glyphosate degradation. There existed appropriate soil moisture to realize high glyphosate degradation efficiency. Glyphosate mineralization was confirmed by changes of total organic carbon (TOC), chemical oxygen demand (COD), PO4(3-) and NO3(-). The degradation intermediates including glycine, aminomethylphosphonic acid, acetic acid, formic acid, PO4(3-) and NO3(-), CO2 and CO were observed. A possible pathway for glyphosate degradation in the soil using this system was proposed. Based on the soil leachate toxicity test using wheat seed germination, the soil did not exhibit any hazardous effects following high-efficiency glyphosate degradation.

  12. Nonintrusive microwave diagnostics of collisional plasmas in Hall thrusters and dielectric barrier discharges

    Science.gov (United States)

    Stults, Joshua

    This research presents a numerical framework for diagnosing electron properties in collisional plasmas. Microwave diagnostics achieved a significant level of development during the middle part of the last century due to work in nuclear weapons and fusion plasma research. With the growing use of plasma-based devices in fields as diverse as space propulsion, materials processing and fluid flow control, there is a need for improved, flexible diagnostic techniques suitable for use under the practical constraints imposed by plasma fields generated in a wide variety of aerospace devices. Much of the current diagnostic methodology in the engineering literature is based on analytical diagnostic, or forward, models. The Appleton-Hartree formula is an oft-used analytical relation for the refractive index of a cold, collisional plasma. Most of the assumptions underlying the model are applicable to diagnostics for plasma fields such as those found in Hall Thrusters and dielectric barrier discharge (DBD) plasma actuators. Among the assumptions is uniform material properties, this assumption is relaxed in the present research by introducing a flexible, numerical model of diagnostic wave propagation that can capture the effects of spatial gradients in the plasma state. The numerical approach is chosen for its flexibility in handling future extensions such as multiple spatial dimensions to account for scattering effects when the spatial extent of the plasma is small relative to the probing beam's width, and velocity dependent collision frequency for situations where the constant collision frequency assumption is not justified. The numerical wave propagation model (forward model) is incorporated into a general tomographic reconstruction framework that enables the combination of multiple interferometry measurements. The combined measurements provide a quantitative picture of the spatial variation in the plasma properties. The benefit of combining multiple measurements in a coherent

  13. Temperature and Nitric Oxide Generation in a Pulsed Arc Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    T.NAMIHIRA; S.SAKAI; M.MATSUDA; D.WANG; T.KIYAN; H.AKIYAMA; K.OKAMOTO; K.TODA

    2007-01-01

    Nitric oxide (NO) is increasingly being used in medical treatments of high blood pressure,acute respiratory distress syndrome and other illnesses related to the lungs.Currently a NO inhalation system consists of a gas cylinder of N2 mixed with a high concentration of NO.This arrangement is potentially risky due to the possibility of an accidental leak of NO from the cylinder.The presence of NO in the air leads to the formation of nitric dioxide (NO2),which is toxic to the lungs.Therefore,an on-site generator of NO would be highly desirable for medical doctors to use with patients with lung disease.To develop the NO inhalation system without a gas cylinder,which would include a high concentration of NO,NAMIHIRA et al have recently reported on the production of NO from room air using a pulsed arc discharge.In the present work,the temperature of the pulsed arc discharge plasma used to generate NO was measured to optimize the discharge condition.The results of the temperature measurements showed the temperature of the pulsed arc discharge plasma reached about 10,000 K immediately after discharge initiation and gradually decreased over tens of microseconds.In addition,it was found that NO was formed in a discharge plasma having temperatures higher than 9,000 K and a smaller input energy into the discharge plasma generates NO more efficiently than a larger one.

  14. High Frequency Discharge Plasma Induced Grafting of Polystyrene onto Titanium Dioxide Powder

    Institute of Scientific and Technical Information of China (English)

    ZHONG Shaofeng; OU Qiongrong; MENG Yuedong

    2007-01-01

    Grafting of polystyrene (PS) onto titanium dioxide powder was investigated. The graft polymerization reaction was induced by high frequency discharge produced N2 plasma treatment of the surfaces of titanium dioxide. IR , XPS and TGA results show that PS was grafted on the titanium dioxide powder. And the crystal structure of the titanium dioxide powder observed by XRD was unchanged after plasma treatment.

  15. Generation of intense soft X-rays from capillary discharge plasmas

    Indian Academy of Sciences (India)

    Y B S R Prasad; S Nigam; K Aneesh; S Barnwal; P K Tripathi; P A Naik; C P Navathe; P D Gupta

    2011-06-01

    X-ray lasing through high voltage, high current discharges in gas filled capillaries has been demonstrated in several laboratories. This method gives highest number of X-ray photons per pulse. The fast varying current and the j x B magnetic force compress the plasma towards the axis forming a hot, dense, line plasma, wherein under appropriate discharge conditions lasing occurs. At Laser Plasma Division, RRCAT, a program on high voltage capillary discharge had been started. The system consists of a 400 kV Marx bank, water line capacitor, spark gap and capillary chamber. The initial results of the emission of intense short soft X-ray pulses (5–10 ns) from the capillary discharge are reported.

  16. Discharge and optical characterizations of nanosecond pulse sliding dielectric barrier discharge plasma for volatile organic compound degradation

    Science.gov (United States)

    Jiang, Nan; Guo, Lianjie; Shang, Kefeng; Lu, Na; Li, Jie; Wu, Yan

    2017-04-01

    In this work, a nanosecond bipolar pulsed voltage coupled with a negative DC component is employed to generate sliding dielectric barrier discharge (DBD) plasma in a three-electrode geometry reactor and improve volatile organic compound (VOC) degradation at room temperature. The effects of the bipolar pulsed voltage (U ±pulse) and negative DC voltage (U ‑DC) on the discharge characteristic, optical characteristic, plasma gas temperature (T gas), and vibrational temperature (T vib) are discussed. The horizontal distribution characteristics of the N2(C3Πu  →  B3Πg) emission intensity, T gas, and T vib are also investigated to understand the propagation mechanism of sliding DBD along the dielectric surface. The experimental results reveal that a negative DC component applied to a third electrode can extend the plasma extension region, indicating that the gas ionization is ignited by the nanosecond high-voltage pulse, while charge drift is forced by the surface potential difference caused by the negative high-voltage DC. The T gas is measured by optical emission spectroscopy related to the rotational bands of N2(C3 Πu  →  B3Πg), and is approximately 375  ±  5 K under the condition of U ±pulse  =  20 kV and U ‑DC  =  ‑20 kV. Compared with typical surface DBD plasma, sliding DBD plasma is quasi-diffusive and distributed more uniformly within the whole discharge gap. Furthermore, both surface DBD and sliding DBD are used for removing toluene from flowing air. It is found that sliding DBD has higher toluene degradation efficiency and energy yield than surface DBD when they are excited by the positive pulsed voltage (U +pulse).

  17. Plasma characteristics of a high power helicon discharge

    Science.gov (United States)

    Ziemba, T.; Euripides, P.; Slough, J.; Winglee, R.; Giersch, L.; Carscadden, J.; Schnackenberg, T.; Isley, S.

    2006-08-01

    A new high power helicon (HPH) plasma system has been designed to provide input powers of several tens of kilowatts to produce a large area (0.5 m2) of uniform high-density, of at least 5 × 1017 m-3, plasma downstream from the helicon coil. Axial and radial plasma characteristics show that the plasma is to a lesser extent created in and near the helicon coil and then is accelerated into the axial and equatorial regions. The bulk acceleration of the plasma is believed to be due to a coupling of the bulk of the electrons to the helicon field, which in turn transfers energy to the ions via ambipolar diffusion. The plasma beta is near unity a few centimetres away from the HPH system and Bdot measurements show ΔB perturbations in the order of the vacuum magnetic field magnitude. In the equatorial region, a magnetic separatrix is seen to develop roughly at the mid-point between the helicon and chamber wall. The magnetic perturbation develops on the time scale of the plasma flow speed and upon the plasma reaching the chamber wall decays to the vacuum magnetic field configuration within 200 µs.

  18. Plasma characteristics of a high power helicon discharge

    Energy Technology Data Exchange (ETDEWEB)

    Ziemba, T; Euripides, P; Slough, J; Winglee, R; Giersch, L; Carscadden, J; Schnackenberg, T; Isley, S [Box 351310, University of Washington, Seattle WA, 98195 (United States)

    2006-08-01

    A new high power helicon (HPH) plasma system has been designed to provide input powers of several tens of kilowatts to produce a large area (0.5 m{sup 2}) of uniform high-density, of at least 5 x 10{sup 17} m{sup -3}, plasma downstream from the helicon coil. Axial and radial plasma characteristics show that the plasma is to a lesser extent created in and near the helicon coil and then is accelerated into the axial and equatorial regions. The bulk acceleration of the plasma is believed to be due to a coupling of the bulk of the electrons to the helicon field, which in turn transfers energy to the ions via ambipolar diffusion. The plasma beta is near unity a few centimetres away from the HPH system and Bdot measurements show {delta}B perturbations in the order of the vacuum magnetic field magnitude. In the equatorial region, a magnetic separatrix is seen to develop roughly at the mid-point between the helicon and chamber wall. The magnetic perturbation develops on the time scale of the plasma flow speed and upon the plasma reaching the chamber wall decays to the vacuum magnetic field configuration within 200 {mu}s.

  19. Plasma discharge in N2 + CH4 at low pressures - Experimental results and applications to Titan

    Science.gov (United States)

    Thompson, W. Reid; Henry, Todd J.; Schwartz, Joel M.; Khare, B. N.; Sagan, Carl

    1991-01-01

    Results are reported from laboratory continuous-flow plasma-discharge experiments designed to simulate the formation of hydrocarbons and nitriles from N2 and CH4 in the atmosphere of Titan. Gas-chromatography and mass-spectrometry data were obtained in experiments lasting up to 100 h at temperature 295 K and pressure 17 or 0.24 mbar, modeling (1) cosmic-ray-induced processes in the Titan troposphere and (2) processes related to stratospheric aurorae excited by energetic electrons and ions from the Saturn magnetosphere, respectively. The results are presented in extensive tables and graphs, and the 0.24-mbar yields are incorporated into an eddy-mixing model to give stratospheric column abundances and mole fractions in good agreement with Voyager IRIS observations.

  20. Study of the operational properties of the Capillary Plasma Electrode (CPE) discharges

    Science.gov (United States)

    Lopez, Jose; Jacome, David; Zhu, Wei-Dong; Figus, Margaret; Becker, Kurt H.

    2009-03-01

    Various approaches have been pursued to create stable atmospheric pressure discharges by extending the lifetime of the diffuse phase of the discharge to hundreds of microseconds. Previous research showed that the stability of the diffuse mode is dependent on the frequency (in the kHz range), gas type power, mode of the excitation, and geometrical confinement. Some of the most promising approaches are based on the recognition of the arc formation in high-pressure plasmas can be avoided and stable high-pressure plasma can be generated and maintained when the plasma are spatially constricted to the dimensions of tens to hundreds of microns. The Capillary Plasma Electrode (CPE) discharge is stable to produce stable atmospheric pressure nonequilibrium plasma. The CPE is similar in design to the Barrier Electrode Discharge, but has perforated dielectrics. The configuration, aside from exhibiting a diffuse mode of operation, also exhibits the so-called ``capillary jet'' mode, in which the capillaries “turn on” and a bright plasma jet emerges from the capillaries. The capillary jets from adjacent capillaries overlap so that the discharge appears uniform when the electrode contains an array of holes. There appears to be a threshold frequency for the capillary jet formation, which is strongly dependent on the L/D ratio of the capillaries, where D is diameter of the capillary and L its length. However, the operating principles and basic properties of this behavior are not well understood. The current work explores these modes of operations of the CPE by characterizing the electrical and optical emission properties of this discharge by examining a multi-hole discharge as well as a single capillary discharge reactor.

  1. Electron dynamics and plasma jet formation in a helium atmospheric pressure dielectric barrier discharge jet

    Energy Technology Data Exchange (ETDEWEB)

    Algwari, Q. Th. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); Electronic Department, College of Electronics Engineering, Mosul University, Mosul 41002 (Iraq); O' Connell, D. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); York Plasma Institute, Department of Physics, University of York, York YO10 5DD (United Kingdom)

    2011-09-19

    The excitation dynamics within the main plasma production region and the plasma jets of a kHz atmospheric pressure dielectric barrier discharge (DBD) jet operated in helium was investigated. Within the dielectric tube, the plasma ignites as a streamer-type discharge. Plasma jets are emitted from both the powered and grounded electrode end; their dynamics are compared and contrasted. Ignition of these jets are quite different; the jet emitted from the powered electrode is ignited with a slight time delay to plasma ignition inside the dielectric tube, while breakdown of the jet at the grounded electrode end is from charging of the dielectric and is therefore dependent on plasma production and transport within the dielectric tube. Present streamer theories can explain these dynamics.

  2. Experimental Study on Indoor Air Cleaning Technique of Nano-Titania Catalysis Under Plasma Discharge

    Institute of Scientific and Technical Information of China (English)

    GAO Deli; YANG Xuechang; ZHOU Fei; WU Yuhuang

    2008-01-01

    In this study, a new technique of air cleaning by plasma combined with catalyst was proposed, which consisted of electrostatic precipitation, volatile organic compounds (VOCs) decomposition and sterilization. A novel indoor air purifier based on this technique was adopted. The experimental results showed that formaldehyde decomposition by the plasma-catalyst hybrid system was more efficient than that by plasma only. Positive discharge was better than negative discharge in formaldehyde removal. Meanwhile, the outlet concentration of ozone byproduct was effectively reduced by the nano-titania catalyst.

  3. Study of the Effect of Decrease in the Conductivity Ahead of a Shock Wave in a Glow-Discharge Plasma

    Science.gov (United States)

    Baryshnikov, A. S.; Basargin, I. V.; Bobashev, S. V.; Monakhov, N. A.; Popov, P. A.; Sakharov, V. A.; Chistyakova, M. V.

    2016-05-01

    The electrical conductivity of a glow-discharge plasma ahead of a shock wave moving perpendicularly to the discharge axis has been investigated using a double electric probe. The obtained results have shown that the interaction of the shock wave with the glow-discharge plasma is accompanied by a change in its conductivity in the entire investigated volume simultaneously.

  4. Influence of the gap size and dielectric constant of the packing on the plasma discharge in a packed bed dielectric barrier discharge reactor: a fluid modeling study

    Science.gov (United States)

    van Laer, Koen; Bogaerts, Annemie

    2016-09-01

    Packed bed dielectric barrier discharge (DBD) reactors have proven to be very useful sources of non-thermal plasma for a wide range of applications, of which the environmental applications have received most attention in recent years. Compared to an empty DBD reactor, a packing was introduced to either enhance the energy efficiency of the process, or, if the packing is catalytically active, steer the process towards a preferred end product. A wide range of geometries, bead sizes and bead materials have been tested experimentally in the past. However, since experimental diagnostics become more difficult with a packing present, a computational study is proposed to gain more insight. Using COMSOL's built in plasma module, a 2D axisymmetric fluid model is developed to study the influence of the gap size and the dielectric constant (ɛ) of the packing. Helium is used as discharge gas, at atmospheric pressure and room temperature. By decreasing the gas gap, the electric field strength is enhanced, resulting in a higher number of current peaks per half cycle of applied rf potential. Increasing ɛ also enhances the electric field strength. However, after a certain ɛ, its influence saturates. The electric field strength will no longer increase, leaving the discharge behavior unchanged.

  5. Plasma-Surface Interactions in Hollow Cathode Discharges for Electric Propulsion

    Science.gov (United States)

    Capece, Angela Maria

    surface state cannot be obtained because of the cathode geometry and high particles fluxes, measurements of the emitter temperature using a two-color pyrometer were used to determine the oxygen surface coverage and characterize the rate processes that occur during poisoning. A model describing the material transport in the plasma discharge was developed and is used to predict the barium and oxygen fluxes to the emitter surface during cathode operation by solving the species continuity and momentum equations. The dominant ionization process for molecular oxygen in the plasma gas is resonant charge exchange with xenon ions. Barium is effectively recycled in the plasma; however, BaO and O2 are not. The model shows that the oxygen flux to the surface is not diffusion limited. Experimental results indicate that the oxygen poisoning rate is slow and that the oxygen poisoning coverage on the emitter surface is less than 3%. A time-dependent model of the reaction kinetics of oxygen and barium at the tungsten surface was developed using the experimental results. The experiments and kinetics model indicate that the dominant processes at the emitter surface are dissociative adsorption of O2, sputtering of the O2 precursor, and desorption of O. Ion sputtering of the weakly bound O2 precursor state limits the poisoning rate and yields low oxygen coverage. Removal of chemisorbed atomic oxygen is dominated by thermal processes. Based on the low oxygen coverage and long poisoning transients, plasma cathodes appear to be able to withstand higher oxygen concentrations than vacuum cathodes.

  6. Temporal evolution of electron density and temperature in capillary discharge plasmas

    Science.gov (United States)

    Oh, Seong Y.; Uhm, Han S.; Kang, Hoonsoo; Lee, In W.; Suk, Hyyong

    2010-05-01

    Time-resolved spectroscopic measurements of a capillary discharge plasma of helium gas were carried out to obtain detailed information about dynamics of the discharge plasma column, where the fast plasma dynamics is determined by the electron density and temperature. Our measurements show that the electron density of the capillary plasma column increases sharply after gas breakdown and reaches its peak of the order of 1018 cm-3 within less than 100 ns, and then it decreases as time goes by. The result indicates that a peak electron density of 2.3×1018 cm-3 occurs about 65 ns after formation of the discharge current, which is ideal for laser wakefield acceleration experiments reported by Karsch et al. [New J. Phys. 9, 415 (2007)].

  7. Long-Lived Vortex Structures in Collisional Pure and Gas-Discharge Nonneutral Electron Plasmas

    CERN Document Server

    Kervalishvili, N A

    2013-01-01

    The analysis of experimental investigations of equilibrium, interaction and dynamics of vortex structures in pure electron and gas-discharge electron nonneutral plasmas during the time much more than the electron-neutral collision time has been carried out. The problem of long confinement of the column of pure electron plasma in Penning-Malmberg trap is considered. The mechanism of stability of long-lived vortex structure in gas-discharge nonneutral electron plasma is investigated. The collapse of electron sheath in gas-discharge nonneutral electron plasma in Penning cell at high pressures of neutral gas is described. The interaction between the stable vortex structure and the annular electron sheath, and the action of vortex structures on the transport of electrons along and across the magnetic field are discussed.

  8. Growth Enhancement of Radish Sprouts Induced by Low Pressure O2 Radio Frequency Discharge Plasma Irradiation

    Science.gov (United States)

    Kitazaki, Satoshi; Koga, Kazunori; Shiratani, Masaharu; Hayashi, Nobuya

    2012-01-01

    We studied growth enhancement of radish sprouts (Raphanus sativus L.) induced by low pressure O2 radio frequency (RF) discharge plasma irradiation. The average length of radish sprouts cultivated for 7 days after O2 plasma irradiation is 30-60% greater than that without irradiation. O2 plasma irradiation does not affect seed germination. The experimental results reveal that oxygen related radicals strongly enhance growth, whereas ions and photons do not.

  9. Preliminary experiment on the negative magneto-resistance effect in a weakly ionized discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Nagata, M.

    2002-04-01

    Compared with the interest in the magneto-resistance effect in solid conductors, the effect in a gas plasma has hardly been addressed. In this work, a theoretical result that a magneto-resistance in an infinite plasma decreases is examined experimentally in an actual discharge plasma. Furthermore, a modified expression for the ambipolar diffusion coefficient in the case where electrons are scattered by heavy neutral atoms is presented. (author)

  10. Treatment Characteristics of Polysaccharides and Endotoxin Using Oxygen Plasma Produced by RF Discharge

    Science.gov (United States)

    Kitazaki, Satoshi; Hayashi, Nobuya; Goto, Masaaki

    2010-10-01

    Treatment of polysaccharides and endotoxin were attempted using oxygen plasma produced by RF discharge. Oxygen radicals observed by optical light emission spectra are factors of decomposition of polysaccharides and endotoxin. Fourier transform infrared spectra indicate that most of chemical bonds in the polysaccharides are dissociated after irradiation of the oxygen plasma. Also, the decomposition rate of endotoxin was approximately 90% after irradiation of the oxygen plasma for 180 min.

  11. Experimental study of a very high frequency, 162 MHz, segmented electrode, capacitively coupled plasma discharge

    Science.gov (United States)

    Sirse, Nishant; Harvey, Cleo; Gaman, Cezar; Ellingboe, Bert

    2016-09-01

    Radio-frequency capacitively coupled plasma (CCP) discharge operating at a very high frequency, 30-300 MHz, offers many advantages over standard 13.56 MHz CCP. However, there is a limited flexibility on the choice of driving frequency and substrate size due to plasma non-uniformity caused by the standing wave effect and edge effect. To overcome this issue segmented electrode CCP's are proposed and researched. Despite its numerous advantages the power coupling mechanism and plasma chemistry in this type of discharge are not fully understood due to lack of experimental data. In this paper, we present the experimental study of a segmented electrode, 3x4 tile array (10x10 cm square tile with 1 cm tile-to-tile separation), CCP discharge driven at 162 MHz. We measured plasma uniformity and gas temperature using hairpin probe and optical emission spectroscopy respectively. A homemade RF compensated Langmuir probe is employed to measure the Electron Energy Distribution Function (EEDF) by second harmonic technique. Energy resolved quadrupole mass spectrometer is utilized to measure the ion energy distribution. Discharge/plasma properties are investigated for several operating conditions and for power coupling mode in both washer board and checker board configuration. The experimental results show that the uniform plasma density can be maintained over a large area along with highly non-equilibrium condition to produce unique gas phase plasma chemistry.

  12. Statistical Analysis of Reducing Biochemical Oxygen Demand (BOD) on Industrial Rubber Wastewater using Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Syakur, Abdul; Zaman, Badrus; Yunita Nurmaliakasih, Dias

    2017-04-01

    Dielectric Barrier Discharge plasma (DBD) is one of type non-thermal plasma (non-equilibrium plasma) or can be referred to as cold plasma. In this research, DBD plasma be utilized to reduce organic compounds like Biochemichal oxygen demand in the wastewater rubber processing. In the environment field DBD plasma has been used as a treatment for reducing air pollutants such as gas COx, NOx and HC. In addition DBD plasma have been developed to processed wastewater as an alternative technology in wastewater treatment. DBD plasma appears when the electrode is given a high voltage so that, it will form electric field in the area of the electrodes which allows the ionization and the presence of high-energy electrons in the area. The presence of these electrons will ionize molecules of H2O into active species such as OH•, H• and H2O2. The active species that can oxidize into CO2 and H2O so, BOD that can be degraded. In this research for wastewater treatment used high voltage are 10kV, 11kV, 12kV and 13kV and variations of processing time for 5, 10, 15, 20, and 25 (minutes). By increasing the voltage and extend the contact time then the speed variation of electrons to ionize the greater and more active species to be formed to degrade the pollutants to the maximum. This research used quantitative analysis with statistical analysis using SPSS software.

  13. A diagnostic system for electrical faults in a high current discharge plasma setup.

    Science.gov (United States)

    Nigam, S; Aneesh, K; Navathe, C P; Gupta, P D

    2011-02-01

    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is ∼4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  14. A diagnostic system for electrical faults in a high current discharge plasma setup

    Science.gov (United States)

    Nigam, S.; Aneesh, K.; Navathe, C. P.; Gupta, P. D.

    2011-02-01

    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is ˜4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  15. RESEARCH OF MICRO ELECTRO DISCHARGE MACHININGEQUIPMENT AND PROCESS TECHNIQUES

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Micro electro discharge machining (micro EDM) is a feasible way to manufacture micro structures and has potential application in advanced industrial fields. For the realization of micro EDM, it is necessary to pay careful attention to its equipment design and the development of process techniques. The present status of research and development of micro EDM equipment and process techniques is overviewed. A micro electro discharge machine incorporated with an inchworm type of micro feed mechanism is introduced, and a micro electro discharge machine for drilling micro holes suitable to industrial use is also introduced. Some of the machining experiments carried out on the micro EDM prototypes are shown and the feasibility of the micro EDM technology to practical use is discussed.

  16. Design of a plasma discharge circuit for particle wakefield acceleration

    CERN Document Server

    Anania, M P; Cianchi, A; Di Giovenale, D; Ferrario, M; Flora, F; Gallerano, G P; Ghigo, A; Marocchino, A; Massimo, F; Mostacci, A; Mezi, L; Musumeci, P; Serio, M; 10.1016/j.nima.2013.10.053

    2014-01-01

    Plasma wakefield acceleration is the most promising acceleration technique known nowadays, able to provide very high accelerating fields (10-100 GV m^-1), enabling acceleration of electrons to GeV energy in few centimetres. However, the quality of the electron bunches accelerated with this technique is still not comparable with that of conventional accelerators; radiofrequency-based accelerators, in fact, are limited in the accelerating field (10-100 MV m^-1) requiring therefore kilometric distances to reach the GeV energies, but can provide very bright electron bunches. Combining high brightness electron bunches from conventional accelerators and high accelerating fields reachable with plasmas could be a good compromise accelerators and high accelerating fields reachable with plasmas could be a good compromise allowing to further accelerate high brightness electron bunches coming from LINAC while preserving electron beam quality. Following the idea of plasma wave resonant excitation driven by a train of shor...

  17. A Study of DC Surface Plasma Discharge in Absence of Free Airflow: Ionic Wind Velocity Profile

    Directory of Open Access Journals (Sweden)

    M. Rafika

    2009-01-01

    Full Text Available In our study we are interested with the DC (Direct Current electric corona discharge created between two wire electrodes. We present experimental results related to some electroaerodynamic actuators based on the DC corona discharge at the surface of a dielectric material. We used different geometrical forms of dielectric surface such as a plate, a cylinder and a wing of aircraft of type NACA 0015. We present the current density-electric filed characteristics for different cases in order to determine the discharge regimes. The corona discharge produces non-thermal plasma so that it is called plasma discharge. Plasma discharge creates a tangential ionic wind above the surface at the vicinity of the wall. We have measured the ionic wind induced by the corona discharge in absence of free external airflow, we give the ionic wind velocity profiles for different surface forms and we compare the actuators effect based on the span of the ionic wind velocity values. We notice that the maximum ionic wind velocity is obtained with the NACA profile, which shows the effectiveness of this actuator for the airflow control.

  18. Research on soft x-rays in high-current plasma-focus discharges and estimation of plasma electron temperature

    Science.gov (United States)

    Skladnik-Sadowska, E.; Zaloga, D.; Sadowski, M. J.; Kwiatkowski, R.; Malinowski, K.; Miklaszewski, R.; Paduch, M.; Surala, W.; Zielinska, E.; Tomaszewski, K.

    2016-09-01

    The paper presents results of experimental studies of dense and high-temperature plasmas, which were produced by pulsed high-current discharges within a modernised PF-1000U facility operated at different initial gas conditions, and supplied from a condenser bank which delivered energy of about 350 kJ. The investigated discharges were performed at the initial deuterium filling under pressure of 1.6-2.0 hPa, with or without an additional puffing of pure deuterium (1 cm3, under pressure 0.15 MPa, at instants 1.5-2 ms before the main discharge initiation). For a comparison discharges were also performed at the initial neon filling under pressure of 1.1-1.3 hPa, with or without the addition of deuterium puffing. The recorded discharge current waveforms, laser interferometric images, signals of hard x-rays and fusion neutrons, as well as time-integrated x-ray pinhole images and time-resolved x-ray signals were compared. From a ratio of the x-ray signals recorded behind beryllium filters of different thickness there were estimated values of a plasma electron temperature (T e) in a region at the electrode outlets. For pure deuterium discharges an averaged T e value amounted to 150-170 eV, while for neon discharges with the deuterium puffing it reached 330-880 eV (with accuracy of  ±20%).

  19. Modeling and simulation of plasma gas flow driven by a single nanosecond-pulsed dielectric barrier discharge

    Science.gov (United States)

    Xu, S. Y.; Cai, J. S.; Li, J.

    2016-10-01

    A simplified (7 species and 9 processes) plasma kinetic model is proposed to investigate the mechanism of the plasma aerodynamic actuation driven by nanosecond-pulsed dielectric barrier discharge (NS-DBD). The governing equations include conservation equations for each species, the Poisson equation for the electric potential, and Navier-Stokes equations for the gas dynamic flow. Numerical simulations of plasma discharge and flow actuation on NS-DBD plasma actuators have been carried out. Key discharge characteristics and the responses of the quiescent air were reproduced and compared to those obtained in experiments and numerical simulations. Results demonstrate that the reduced plasma kinetic model is able to capture the dominant species and reactions to predict the actuation in complicated hydrodynamics. For the one-dimensional planar and two-dimensional symmetric NS-DBD, the forming of the sheath collapse is mainly due to the charge accumulation and secondary emission from the grounded electrode. Rapid species number density rise and electric field drop occur at the edge of the plasma sheath, where the space charge density gradient peaks. For the aerodynamic actuation with typical asymmetry electrodes, discharge characteristics have a core area on the right edge of the upper electrode, where the value can be much higher. The formation and propagation of the compression waves generated through rapid heating have also been performed and compared to those measured in a recent experiment. Energy release leads to gas expansion and forms a cylindrical shock wave, centering at the upper electrode tip with low gas acceleration. For the present single pulsed 12 kV case, the mean temperature of gas heating reaches about 575 K at 1 μs and decreases to about 460 K at 10 μs.

  20. Differential Inactivation of Fungal Spores in Water and on Seeds by Ozone and Arc Discharge Plasma.

    Directory of Open Access Journals (Sweden)

    Min Ho Kang

    Full Text Available Seed sterilization is essential for preventing seed borne fungal diseases. Sterilization tools based on physical technologies have recently received much attention. However, available information is very limited in terms of efficiency, safety, and mode of action. In this study, we have examined antifungal activity of ozone and arc discharge plasma, potential tools for seed sterilization. In our results, ozone and arc discharge plasma have shown differential antifungal effects, depending on the environment associated with fungal spores (freely submerged in water or infected seeds. Ozone inactivates Fusarium fujikuroi (fungus causing rice bakanae disease spores submerged in water more efficiently than arc discharge plasma. However, fungal spores associated with or infecting rice seeds are more effectively deactivated by arc discharge plasma. ROS generated in water by ozone may function as a powerful fungicidal factor. On the other hand, shockwave generated from arc discharge plasma may have greatly contributed to antifungal effects on fungus associated with rice seeds. In support of this notion, addition of ultrasonic wave in ozone generating water has greatly increased the efficiency of seed disinfection.

  1. Differential Inactivation of Fungal Spores in Water and on Seeds by Ozone and Arc Discharge Plasma

    Science.gov (United States)

    Kang, Min Ho; Pengkit, Anchalee; Choi, Kihong; Jeon, Seong Sil; Choi, Hyo Won; Shin, Dong Bum; Choi, Eun Ha; Uhm, Han Sup; Park, Gyungsoon

    2015-01-01

    Seed sterilization is essential for preventing seed borne fungal diseases. Sterilization tools based on physical technologies have recently received much attention. However, available information is very limited in terms of efficiency, safety, and mode of action. In this study, we have examined antifungal activity of ozone and arc discharge plasma, potential tools for seed sterilization. In our results, ozone and arc discharge plasma have shown differential antifungal effects, depending on the environment associated with fungal spores (freely submerged in water or infected seeds). Ozone inactivates Fusarium fujikuroi (fungus causing rice bakanae disease) spores submerged in water more efficiently than arc discharge plasma. However, fungal spores associated with or infecting rice seeds are more effectively deactivated by arc discharge plasma. ROS generated in water by ozone may function as a powerful fungicidal factor. On the other hand, shockwave generated from arc discharge plasma may have greatly contributed to antifungal effects on fungus associated with rice seeds. In support of this notion, addition of ultrasonic wave in ozone generating water has greatly increased the efficiency of seed disinfection. PMID:26406468

  2. Vibrational excitation in O2and Cl2inductively-coupled plasmas and DC discharges

    Science.gov (United States)

    Booth, Jean-Paul; Marinov, Daniil; Foucher, Mickael; Annusova, Adriana; Guerra, Vasco

    2016-09-01

    Low-energy electrons can interact with molecules via resonances to cause vibrational excitation with large cross-sections. Such processes can absorb significant energy from the plasma electrons, affecting the electron energy distribution and potentially (via vibration-translation (VT) energy transfer) causing substantial gas heating. The presence of vibrationally excited molecules may significant increase the rates of collisional processes, including electron dissociative attachment and electron impact dissociation into neutral atoms. However, the cross-sections of these processes are often poorly known since they are extremely difficult to measure directly, and reliable theoretical calculations are only now appearing for simple diatomic molecules. We have measured the vibrational distributions in discharges in pure O2 and pure Cl2, using high-sensitivity ultra-broadband ultraviolet absorption spectroscopy. In O2 plasmas significant vibrational excitation is observed, up to v'' =18, with a tail temperature of around 8000K. In Cl2 excitation is only observed up to v'' =3, and the distribution appears to be in local equilibrium with the gas translational temperature (up to 1500K). We are developing a detailed self-consistent 0D global model of these systems including vibrational excitation. Work performed in the LABEX Plas@par project, with financial state aid (ANR-11-IDEX-0004-02 and ANR-13-BS09-0019).

  3. Generation of uniform atmospheric pressure argon glow plasma by dielectric barrier discharge

    Indian Academy of Sciences (India)

    Raju Bhai Tyata; Deepak Prasad Subedi; Rajendra Shrestha; Chiow San Wong

    2013-03-01

    In this paper, atmospheric pressure glow discharges (APGD) in argon generated in parallel plate dielectric barrier discharge system is investigated by means of electrical and optical measurements. Using a high voltage (0–20 kV) power supply operating at 10–30 kHz, homogeneous and steady APGD has been observed between the electrodes with gap spacing from 0.5 mm to 2 mm and with a dielectric barrier of thickness 2 mm while argon gas is fed at a controlled flow rate of 11/min. The electron temperature and electron density of the plasma are determined by means of optical emission spectroscopy. Our results show that the electron density of the discharge obtained is of the order of 1016 cm-3 while the electron temperature is estimated to be 0.65 eV. The important result is that electron density determined from the line intensity ratio method and stark broadening method are in very good agreement. The Lissajous figure is used to estimate the energy deposited to the glow discharge. It is found that the energy deposited to the discharge is in the range of 20 to 25 $\\$J with a discharge voltage of 1.85 kV. The energy deposited to the discharge is observed to be higher at smaller gas spacing. The glow discharge plasma is tested to be effective in reducing the hydrophobicity of polyethylene film significantly.

  4. Investigation of Plasma Polymerized Maleic Anhydride Film in a Middle Frequency Dielectric Barrier Discharge

    Institute of Scientific and Technical Information of China (English)

    TANG Wenjie; CHEN Qiang; ZHANG Yuefei; GE Yuanjing

    2008-01-01

    Plasma polymerized maleic anhydride (MA) was carried out by using maleic anhydride supersaturated ethanol solution as a precursor in a dielectric barrier discharge (DBD). The film properties were characterized by water contact angle (WCA), Fourier transfer infrared (FTIR), X-ray photoelectron spectroscopy (XPS), atomic force microscope (AFM) analysis, and a thickness profilometer. The influence of the processing parameters on the film properties such as the power frequency, and polymerization zone was investigated. The results show that anhydride group incorporated into the growing films is favorable at the frequency of 80 kHz and working pressure of 50 Pa. The poly (maleic anhydride) film is uniform and compact at an average deposition rate of 8 nm/min.

  5. Conversion of carbon dioxide to carbon monoxide by pulse dielectric barrier discharge plasma

    Science.gov (United States)

    Wang, Taobo; Liu, Hongxia; Xiong, Xiang; Feng, Xinxin

    2017-01-01

    The conversion of carbon dioxide (CO2) to carbon monoxide (CO) was investigated in a non-thermal plasma dielectric barrier discharge (DBD) reactor, and the effects of different process conditions on the CO2 conversion were investigated. The results showed that the increase of input power could optimize the conversion of CO2 to CO. The CO2 conversion and CO yield were negatively correlated with the gas flow rate, but there was an optimum gas flow rate, that made the CO selectivity best. The carrier gas (N2, Ar) was conducive to the conversion of CO2, and the effect of N2 as carrier gas was better than Ar. The conversion of CO2 to CO was enhanced by addition of the catalyst (5A molecular sieve).

  6. A hybrid model of radio frequency biased inductively coupled plasma discharges: description of model and experimental validation in argon

    Science.gov (United States)

    Wen, De-Qi; Liu, Wei; Gao, Fei; Lieberman, M. A.; Wang, You-Nian

    2016-08-01

    A hybrid model, i.e. a global model coupled bidirectionally with a parallel Monte-Carlo collision (MCC) sheath model, is developed to investigate an inductively coupled discharge with a bias source. This hybrid model can self-consistently reveal the interaction between the bulk plasma and the radio frequency (rf) bias sheath. More specifically, the plasma parameters affecting characteristics of rf bias sheath (sheath length and self-bias) are calculated by a global model and the effect of the rf bias sheath on the bulk plasma is determined by the voltage drop of the rf bias sheath. Moreover, specific numbers of ions are tracked in the rf bias sheath and ultimately the ion energy distribution function (IEDF) incident on the bias electrode is obtained. To validate this model, both bulk plasma density and IEDF on the bias electrode in an argon discharge are compared with experimental measurements, and a good agreement is obtained. The advantage of this model is that it can quickly calculate the bulk plasma density and IEDF on the bias electrode, which are of practical interest in industrial plasma processing, and the model could be easily extended to serve for industrial gases.

  7. UNJUK KERJA REAKTOR PLASMA DIELECTRIC BARRIER DISCHARGE UNTUK PRODUKSI BIODIESEL DARI MINYAK KELAPA SAWIT

    Directory of Open Access Journals (Sweden)

    Ardian Dwi Yudhistira

    2013-10-01

    Full Text Available Biodiesel is one of alternative renewable energy source to substitute diesel fuel. Various biodiesel productionprocesses through transesterification reaction with a variety of catalysts have been developed by previousresearcher. This process still has the disadvantage of a long reaction time, and high energy need. DielectricBarrier Discharge (DBD plasma electro-catalysis may become a solution to overcome the drawbacks in theconventional transesterification process. This process only needs a short time reaction and low energy process.The purpose of this study was to assess the performance of DBD plasma rector in making biodiesel such as: theeffect of high voltage electric value, electrodes gap, mole ratio of methanol / oil, and reaction time. TheResearch method was using GC-MS (Gas Cromatography-Mass Spectrofotometry and FTIR (FourierTransform Infrared Spectrofotometry and then it will be analysed the change of chemical bond betweenreactant and product. So, the reaction mechanism can be predicted. Biodiesel is produced using methanol andpalm oil as reactants and DBD plasma used as reactor in batch system. Then, reactants contacted by highvoltage electric. From the results of this research can be concluded that the reaction mechanism occurs in theprocess is the reaction mechanism of cracking, the higher of electric voltage and the longer of reaction time leadto increasing of product yield. The more of mole ratio of methanol / oil and widening the gap between theelectrodes lead to decreased product yield. From this research, product yield maksimum is 89,8% in the variableof rasio mol metanol/palm oil 3:1, voltage 10 kV, electrode gap 1,5 cm, and reaction time 30 seconds.

  8. Characterization of a dielectric barrier discharge in contact with liquid and producing a plasma activated water

    Science.gov (United States)

    Neretti, G.; Taglioli, M.; Colonna, G.; Borghi, C. A.

    2017-01-01

    In this work a low-temperature plasma source for the generation of plasma activated water (PAW) is developed and characterized. The plasma reactor was operated by means of an atmospheric-pressure air dielectric barrier discharge (DBD). The plasma generated is in contact with the water surface and is able to chemically activate the liquid medium. Electrodes were supplied by both sinusoidal and nanosecond-pulsed voltage waveforms. Treatment times were varied from 2 to 12 min to increase the energy dose released to the water by the DBD plasma. The physics of the discharge was studied by means of electrical, spectroscopic and imaging diagnostics. The interaction between the plasma and the liquid was investigated as well. Temperature and composition of the treated water were detected. Images of the discharges showed a filamentary behaviour in the sinusoidal case and a more homogeneous behaviour in the nanosecond-pulsed one. The images and the electrical measurements allowed to evaluate an average electron number density of about 4  ×  1019 and 6  ×  1017 m-3 for the sinusoidal and nanosecond-pulsed discharges respectively. Electron temperatures in the range of 2.1÷2.6 eV were measured by using spectroscopic diagnostics. Rotational temperatures in the range of 318-475 K were estimated by fitting synthetic spectra with the measured ones. Water temperature and pH level did not change significantly after the exposure to the DBD plasma. The production of ozone and hydrogen peroxide within the water was enhanced by increasing the plasma treatment time and the energy dose. Numerical simulations of the nanosecond-pulsed discharge were performed by using a self-consistent coupling of state-to-state kinetics of the air mixture with the Boltzmann equation of free electron kinetics. Temporal evolution of the electron energy distribution function shows departure from the Maxwellian distribution especially during the afterglow phase of the discharge. When

  9. Investigation of Atmospheric Plasma Discharge and Its Application to Surface Modification of Textile Materials

    Institute of Scientific and Technical Information of China (English)

    TANG Xiao-liang; QIU Gao; FENG Xian-ping; YAN Yong-hui; SHI Yun-cheng; YAN Zhi-ren; WANG Liang

    2005-01-01

    In this paper, an improved quasi-stable atmospheric pressure dielectric barrier discharge (DBD) plasma source is achieved after carefully controlled discharge voltage and current, discharge power, working gas, treatment period,and gap between the electrodes. This plasma source has been used to modify the surface of Polybutylene Terephthalate (PBT) melt-blown nonwovens and Polyester(PET) fabrics, and the various influences on surface modification and the aging effeet of treated polymeric materials have been systematically investigated. In addition, the method of spectrum analysis is also used for diagnosing plasma parameters such as electron temperature.Experimental results indicate that both the wettablity and permeation of treated PBT melt-blown nonwovens and dyeing ability of treated PET fabrics are certainly improved.

  10. Inactivation of Escherichia Coli Using Remote Low Temperature Glow Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    HU Miao; CHEN Jierong; CHEN Chua

    2008-01-01

    Low-temperature plasma is distinguished as a developing approach for sterilization which can deal with and overcome those problems such as thermal sensitivity and destruction by heat,formation of toxic by-products,higher costs and inefficiency in performances,caused by conventional methods.In this study,an experimental investigation was undertaken to characterize the effects of the operational parameters,such as treating time,discharge power and gas flow rate,of remote glow discharge air plasma.The results show that the inactivation of Escherichia coli can reach above 99.99% in less than 60 seconds and the optimal operational conditions for treating time,discharge power and gas flow rate were:40 s,80 W and 60 cm3/min,respectively.The contribution of UV radiation during plasma germ deactivation is very limited.

  11. Second-harmonic plasma response in diffusion-controlled surface-wave-sustained discharges

    Science.gov (United States)

    Stoev, L.

    2008-05-01

    The formation of nonlinear plasma response at the second harmonic frequency in diffusion controlled surface-wave-sustained discharges is studied theoretically. The study is aimed at estimating theoretically the ratio of the squared amplitudes of the wave field of fundamental frequency and of the resulting - from the nonlinear effects - electric field at the second harmonic frequency. The model presented is intended for further use in discharge diagnostics.

  12. Modification of polylactic acid surface using RF plasma discharge with sputter deposition of a hydroxyapatite target for increased biocompatibility

    Energy Technology Data Exchange (ETDEWEB)

    Tverdokhlebov, S.I., E-mail: tverd@tpu.ru [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation); Bolbasov, E.N.; Shesterikov, E.V. [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation); Antonova, L.V.; Golovkin, A.S.; Matveeva, V.G. [Federal State Budgetary Institution Research Institute for Complex Issues of Cardiovascular Disease, 6 Sosnovy Blvd, Kemerovo 650002 (Russian Federation); Petlin, D.G.; Anissimov, Y.G. [Griffith University, School of Natural Sciences, Engineering Dr., Southport, QLD 4222 (Australia)

    2015-02-28

    Highlights: • The treatment by plasma of radio-frequency magnetron discharge with hydroxyapatite target sputtering improves the biocompatibility of PLLA surface. • The treatment significantly increases the roughness of PLLA surface. • The formation of rough highly porous surface is due to the etching and crystallization processes on PLLA surface during treatment. • Maximum concentration of the ions from the sputtered target is achieved at 60 s of the plasma treatment. - Abstract: Surface modification of polylactic acid (PLLA) by plasma of radio-frequency magnetron discharge with hydroxyapatite target sputtering was investigated. Increased biocompatibility was demonstrated using studies with bone marrow multipotent mesenchymal stromal cells. Atomic force microscopy demonstrates that the plasma treatment modifies the surface morphology of PLLA to produce rougher surface. Infrared spectroscopy and X-ray diffraction revealed that changes in the surface morphology are caused by the processes of PLLA crystallization. Fluorescent X-ray spectroscopy showed that the plasma treatment also changes the chemical composition of PLLA, enriching it with ions of the sputtered target: calcium, phosphorus and oxygen. It is hypothesized that these surface modifications increase biocompatibility of PLLA without increasing toxicity.

  13. Reduction of TiO2 with hydrogen cold plasma in DC pulsed glow discharge

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yu-wen; DING Wei-zhong; LU Xiong-gang; GUO Shu-qiang; XU Kuang-di

    2005-01-01

    The reduction of TiO2 to Ti2O3 with hydrogen cold plasma generated by a DC pulsed glow discharge was realized under 2 500 Pa at 1 233 K. Only a little of Ti10O19 and Ti9O17 was detected for using molecular hydrogen.Enhancement effects of hydrogen cold plasma on the reduction were discussed in terms of thermodynamic coupling,kinetics and plasma sheath. The exited hydrogen species are considered more effective reducing agents. It is instructive to reduce refractory oxides with plasma hydrogen at the reduced temperature.

  14. Broadband and long lifetime plasma-antenna in air initiated by laser-guided discharge

    Science.gov (United States)

    Théberge, Francis; Gravel, Jean-François; Kieffer, Jean-Claude; Vidal, François; Châteauneuf, Marc

    2017-08-01

    In this work, we demonstrate the coupling and emission of radio-frequency (RF) signals from laser-guided discharge in ambient air. The produced 100-cm long plasma-antenna is broadband and can emit RF signals for more than 2 ms, which corresponds to an enhancement of the plasma-antenna lifetime of 4 orders of magnitude relative to previous demonstrations using laser-based plasma filamentation. The generation of large diameter plasma-antennas in the air allows to broadcast RF signals efficiently from ˜10 MHz to few tens of GHz.

  15. Diagnostics of Atmospheric Pressure Surface Discharge Plasmas in Argon

    Institute of Scientific and Technical Information of China (English)

    张锐; 詹如娟; 温晓辉

    2003-01-01

    Atmospheric pressure surface discharge is shown to have great prospects for a number of industrial applications.To acquire better results in application fields and considering that the study of the basic parameters including electron temperature and electron density is desirable,we develop an equivalent circuit model and the diagnostic techniques based on optical emission spectroscopy and electrical measurement in our laboratory.The electron temperature has been determined to be about 0.7eV by a Fermi-Dirac model.The electron density has been calculated to be near 1010 cm-3 from a time resolved electrical measurement(Ohmic heating method).

  16. Dyeing mechanism and optimization of polyamide 6,6 functionalized with double barrier discharge (DBD) plasma in air

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Fernando Ribeiro [Departamento de Engenharia Têxtil, Universidade Federal do Rio Grande do Norte UFRN, 59.072-970 Natal (Brazil); Zille, Andrea, E-mail: azille@2c2t.uminho.pt [2C2T – Centro de Ciência e Tecnologia Têxtil, Departamento de Engenharia Têxtil, Universidade do Minho, 4800-058 Guimarães (Portugal); Souto, Antonio Pedro [2C2T – Centro de Ciência e Tecnologia Têxtil, Departamento de Engenharia Têxtil, Universidade do Minho, 4800-058 Guimarães (Portugal)

    2014-02-28

    The physico-chemical improvements occasioned by DBD plasma discharge in dyeing process of polyamide 6,6 (PA66) fibers were investigated. The SEM, fluorescence microscopy, UV–vis spectroscopy, surface energy, FTIR, XPS and pH of aqueous extracts confirm the high polar functionalization of PA66 fibers due to plasma incorporation of oxygen atoms from atmospheric air. DBD plasma-generated reactive species preferentially break the C-N bonds, and not the aliphatic C-C chain of PA66. Formation of low-molecular weight acidic molecules that act as dye “carrier” and creation of micro-channels onto PA66 surface seems to favor dye diffusion into the fiber cores. Plasma treatment allows high level of direct dye diffusion and fixation in PA66 fibers at lower temperatures and shorter dyeing times than traditional dyeing methods.

  17. Plasma discharge and time-dependence of its effect to bacteria.

    Science.gov (United States)

    Justan, I; Cernohorska, L; Dvorak, Z; Slavicek, P

    2014-07-01

    Several types of plasma discharge have been proven to have a capacity for sterilization. Our goal is to introduce new nonthermal plasma pencil. We used it to sterilize different microbial populations with differing ages. We used a plasma discharge of the following characteristics: radio frequency barrier discharger at atmospheric pressure with a working frequency of 13.56 MHz, and the working gas used was argon. We performed 110 tests with the following microbial populations: Pseudomonas aeruginosa, Staphylococcus aureus, Proteus species, and Klebsiella pneumoniae. All populations were inoculated on the previous day and also on the day of our experiment. We made our evaluations the following day and also after 5 days, with all our microbial populations. Eradication of microbial populations is dependent on the plasma discharge exposure time in all cases. With regard to freshly inoculated microbes, we were able to sterilize agar with intensive exposure lasting for 10 s of colonies Pseudomonas, Proteus, and Klebsiella. The most resistant microbe seems to be S. aureus, which survives 5 s of coherent exposure in half of the cases. Using the lightest plasma discharge exposure, we achieved a maximum of 10(4)-10(5) CFU/mL (colony-forming unit - CFU). Regarding older microbial populations inoculated the day before the experiment, we can only decrease population growth to 10(5) CFU/mL approximately, but never completely sterilize. The plasma discharge with our characteristics could be used for the sterilization of the aforementioned superficially growing microbes, but does not sufficiently affect deeper layers and thus seems to be a limitation for eradication of the already erupted colonies.

  18. Nanosecond pulsed sliding dielectric barrier discharge plasma actuator for airflow control: Electrical, optical, and mechanical characteristics

    Science.gov (United States)

    Bayoda, K. D.; Benard, N.; Moreau, E.

    2015-08-01

    Plasma actuators used for active flow control are widely studied because they could replace mechanical actuators. Industrial applications of these plasma actuators sometimes require a large surface plasma sheet in view of increasing the interaction region between the discharge and the incoming flow. Instead of using a typical two-electrode nanosecond pulsed dielectric barrier discharge for which the interaction region is limited to about 20 mm, this study proposes to characterize a nanosecond sliding discharge based on a three-electrode geometry in order to increase the extension length up to the electrode gap. This sliding discharge is compared to the typical nanosecond dielectric barrier discharge by means of electrical, optical, and mechanical diagnostics. Electrical characterization reveals that the deposited energy can be widely increased. Time-resolved Intensified Charge Coupled Device (iCCD) images of the discharge development over the dielectric surface highlight that the intensity and the propagation velocity of streamers are strongly affected by the DC voltage applied at the third electrode. Finally, qualitative and quantitative characterizations of the pressure wave due to the surrounding gas heating are proposed by means of Schlieren visualizations and high frequency pressure measurements, respectively.

  19. Laser-induced optogalvanic signal oscillations in miniature neon glow discharge plasma.

    Science.gov (United States)

    Saini, V K

    2013-06-20

    Laser-induced optogalvanic (OG) signal oscillations detected in miniature neon glow discharge plasma are investigated using a discharge equivalent-circuit model. The damped oscillations in OG signal are generated when a pulsed dye laser is tuned to a specific neon transition (1s5→2p2) at 588.2 nm under the discharge conditions where dynamic resistance changes its sign. Penning ionization via quasi-resonant energy transfer collisions between neon gas atoms in metastable state and sputtered electrode atoms in ground state is discussed to explain the negative differential resistance properties of discharge plasma that are attributed to oscillations in the OG signal. The experimentally observed results are simulated by analyzing the behavior of an equivalent discharge-OG circuit. Good agreement between theoretically calculated and experimental results is observed. It is found that discharge plasma is more sensitive and less stable in close vicinity to dynamic resistance sign inversion, which can be useful for weak-optical-transition OG detection.

  20. Characterization of the Basic Operational Properties of the Capillary Plasma Electrode (CPE) Discharge

    Science.gov (United States)

    Lopez, Jose; Zhu, Weidong; Figus, Margaret; Becker, Kurt

    2008-10-01

    Various approaches have been pursued to create stable atmospheric pressure discharges by extending the lifetime of the diffuse phase of the discharge to hundreds of microseconds. Previous research showed that the stability of the diffuse mode is dependent on the frequency (in the kHz range), gas type, power, mode of the excitation, and geometrical confinement. The Capillary Plasma Electrode (CPE) discharge is able to produce stable atmospheric pressure nonequilibrium plasmas. The CPE is similar in design to a barrier-electrode discharge, but has perforated dielectrics. This configuration, aside from exhibiting a diffuse mode of operation, also exhibits the so-called ``capillary jet'' mode, in which the capillaries ``turn on'' and a bright plasma jet emerges from the capillaries. The capillary jets from adjacent capillaries overlap so that the discharge appears uniform when the electrode contains an array of holes. There appears to be a threshold frequency for the capillary jet formation, which is strongly dependent on the L/D ratio of the capillaries, where D is the diameter of a capillary and L its length. This current work explores these modes of operation of the CPE by characterizing the electrical and optical emission properties of this discharge.

  1. Modification of a metallic surface in a vacuum arc discharge plasma using thermally stimulated ion diffusion

    Science.gov (United States)

    Muboyadzhyan, S. A.

    2008-12-01

    A new process for modifying a metallic surface in a vacuum arc discharge plasma using thermally stimulated ion diffusion is considered. The effect of the bias voltage (negative substrate potential) on the processes that occur on the surface of a treated part is studied when the substrate material interacts with an accelerated metallic-ion flow. The phase and elemental compositions of the modified layer are studied for substrates made of nickel-based superalloys, austenitic and martensitic steels, and titanium-based alloys. The heat resistance, the salt corrosion resistance, and the corrosion cracking resistance of steels and titanium-based alloys are investigated after their modification in vacuum arc plasmas of pure metals (Ti, Zr, Al, Cr, Y) and related alloys. The surface modification caused by the thermally stimulated ion saturation of the surfaces of parts made from structural materials is shown to change the structural-phase states of their surfaces and, correspondingly, the properties of these materials in relation to the state of the surface.

  2. Effect of plasma processing reactor circuitry on plasma characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Rauf, S.; Kushner, M.J. [Univ. of Illinois, Urbana, IL (United States). Dept. of Electrical and Computer Engineering

    1997-12-31

    It is well known that external circuitry greatly influences the performance of plasma processing reactors. Simulation of external circuits difficult since the time in which the external circuit attains the steady-state is several orders of magnitude longer than typical plasma simulation time scales. In this paper, the authors present a technique to simulate the external circuit concurrently with the plasma, and implement it into the Hybrid Plasma Equipment Model (HPEM). The resulting model is used to investigate the influence of external circuitry on plasma behavior.

  3. Laser-guided energetic discharges over large air gaps by electric-field enhanced plasma filaments

    Science.gov (United States)

    Théberge, Francis; Daigle, Jean-François; Kieffer, Jean-Claude; Vidal, François; Châteauneuf , Marc

    2017-01-01

    Recent works on plasma channels produced during the propagation of ultrashort and intense laser pulses in air demonstrated the guiding of electric discharges along the laser path. However, the short plasma lifetime limits the length of the laser-guided discharge. In this paper, the conductivity and lifetime of long plasma channels produced by ultrashort laser pulses is enhanced efficiently over many orders of magnitude by the electric field of a hybrid AC-DC high-voltage source. The AC electric pulse from a Tesla coil allowed to stimulate and maintain the highly conductive channel during few milliseconds in order to guide a subsequent 500 times more energetic discharge from a 30-kV DC source. This DC discharge was laser-guided over an air gap length of two metres, which is more than two orders of magnitude longer than the expected natural discharge length. Long plasma channel induced by laser pulses and stimulated by an external high-voltage source opens the way for wireless and efficient transportation of energetic current pulses over long air gaps and potentially for guiding lightning. PMID:28053312

  4. Laser-guided energetic discharges over large air gaps by electric-field enhanced plasma filaments

    Science.gov (United States)

    Théberge, Francis; Daigle, Jean-François; Kieffer, Jean-Claude; Vidal, François; Châteauneuf, Marc

    2017-01-01

    Recent works on plasma channels produced during the propagation of ultrashort and intense laser pulses in air demonstrated the guiding of electric discharges along the laser path. However, the short plasma lifetime limits the length of the laser-guided discharge. In this paper, the conductivity and lifetime of long plasma channels produced by ultrashort laser pulses is enhanced efficiently over many orders of magnitude by the electric field of a hybrid AC-DC high-voltage source. The AC electric pulse from a Tesla coil allowed to stimulate and maintain the highly conductive channel during few milliseconds in order to guide a subsequent 500 times more energetic discharge from a 30-kV DC source. This DC discharge was laser-guided over an air gap length of two metres, which is more than two orders of magnitude longer than the expected natural discharge length. Long plasma channel induced by laser pulses and stimulated by an external high-voltage source opens the way for wireless and efficient transportation of energetic current pulses over long air gaps and potentially for guiding lightning.

  5. Radiative heat transfer in plasma of pulsed high pressure caesium discharge

    Science.gov (United States)

    Lapshin, V. F.

    2016-01-01

    Two-temperature many component gas dynamic model is used for the analysis of features of radiative heat transfer in pulsed high pressure caesium discharge plasma. It is shown that at a sufficiently high pressure the radial optical thickness of arc column is close to unit (τR (λ) ∼ 1) in most part of spectrum. In this case radiative heat transfer has not local character. In these conditions the photons which are emitted in any point of plasma volume are absorbed in other point remote from an emission point on considerable distance. As a result, the most part of the electric energy put in the discharge mainly near its axis is almost instantly redistributed on all volume of discharge column. In such discharge radial profiles of temperature are smooth. In case of low pressure, when discharge plasma is optically transparent for own radiation in the most part of a spectrum (τR(λ) << 1), the emission of radiation without reabsorption takes place. Radiative heat transfer in plasma has local character and profiles of temperature have considerable gradient.

  6. Effect of Inductive Coil Geometry on the Thrust Efficiency of a Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley; Polzin, Kurt; Emsellem, Gregory

    2012-01-01

    Pulsed inductive plasma thrusters [1-3] are spacecraft propulsion devices in which electrical energy is capacitively stored and then discharged through an inductive coil. The thruster is electrodeless, with a time-varying current in the coil interacting with a plasma covering the face of the coil to induce a plasma current. Propellant is accelerated and expelled at a high exhaust velocity (O(10-100 km/s)) by the Lorentz body force arising from the interaction of the magnetic field and the induced plasma current. While this class of thruster mitigates the life-limiting issues associated with electrode erosion, pulsed inductive plasma thrusters require high pulse energies to inductively ionize propellant. The Microwave Assisted Discharge Inductive Plasma Accelerator (MAD-IPA) [4, 5] is a pulsed inductive plasma thruster that addressees this issue by partially ionizing propellant inside a conical inductive coil via an electron cyclotron resonance (ECR) discharge. The ECR plasma is produced using microwaves and permanent magnets that are arranged to create a thin resonance region along the inner surface of the coil, restricting plasma formation, and in turn current sheet formation, to a region where the magnetic coupling between the plasma and the inductive coil is high. The use of a conical theta-pinch coil is under investigation. The conical geometry serves to provide neutral propellant containment and plasma plume focusing that is improved relative to the more common planar geometry of the Pulsed Inductive Thruster (PIT) [2, 3], however a conical coil imparts a direct radial acceleration of the current sheet that serves to rapidly decouple the propellant from the coil, limiting the direct axial electromagnetic acceleration in favor of an indirect acceleration mechanism that requires significant heating of the propellant within the volume bounded by the current sheet. In this paper, we describe thrust stand measurements performed to characterize the performance

  7. Effects of background gas on sulfur hexafluoride removal by atmospheric dielectric barrier discharge plasma

    Science.gov (United States)

    Zhang, Xiaoxing; Xiao, Hanyan; Hu, Xiongxiong; Gui, Yingang

    2016-11-01

    The effects of background gases (He, Ar, N2 and air) on SF6 removal in a dielectric barrier reactor were investigated at atmospheric pressure. A comparison among these background gases was performed in terms of discharge voltage, discharge power, mean electron energy, electron density, removal efficiency and energy yield for the destruction of SF6. Results showed that the discharge voltage of He and Ar was lower than that of N2 and air, but the difference of their discharge power was small. Compared with three other background gases, Ar had a relatively superior destruction and removal rate and energy yield since the mean electron energy and electron density in SF6/H2O/Ar plasma were both maintained at a high level. Complete removal of 2% SF6 could be achieved at a discharge power of 48.86 W with Ar and the corresponding energy yield can reach 4.8 g/kWh.

  8. Effects of background gas on sulfur hexafluoride removal by atmospheric dielectric barrier discharge plasma

    Directory of Open Access Journals (Sweden)

    Xiaoxing Zhang

    2016-11-01

    Full Text Available The effects of background gases (He, Ar, N2 and air on SF6 removal in a dielectric barrier reactor were investigated at atmospheric pressure. A comparison among these background gases was performed in terms of discharge voltage, discharge power, mean electron energy, electron density, removal efficiency and energy yield for the destruction of SF6. Results showed that the discharge voltage of He and Ar was lower than that of N2 and air, but the difference of their discharge power was small. Compared with three other background gases, Ar had a relatively superior destruction and removal rate and energy yield since the mean electron energy and electron density in SF6/H2O/Ar plasma were both maintained at a high level. Complete removal of 2% SF6 could be achieved at a discharge power of 48.86 W with Ar and the corresponding energy yield can reach 4.8 g/kWh.

  9. Chaotic-to-ordered state transition of cathode-sheath instabilities in DC glow discharge plasmas

    Indian Academy of Sciences (India)

    Md Nurujjaman; A N Sekar Iyengar

    2006-08-01

    Transition from chaotic to ordered state has been observed during the initial stage of a discharge in a cylindrical DC glow discharge plasma. Initially it shows a chaotic behavior but increasing the discharge voltage changes the characteristics of the discharge glow and shows a period subtraction of order 7 period → 5 period → 3 period → 1 period, i.e. the system goes to single mode through odd cycle subtraction. On further increasing the discharge voltage, the system goes through period doubling, like 1 period → 2 period → 4 period. On further increasing the voltage, the system goes to stable state through two period subtraction, like 4 period → 2 period → stable.

  10. Instability Parameters of Optical Oscillation Frequency in Plasma Central Discharge and Periphery Region

    Institute of Scientific and Technical Information of China (English)

    ZHOU Zhu-Wen; M.A.LIEBERMAN; Sungjin KIM

    2006-01-01

    @@ We have observed relaxation oscillations in a capacitive discharge in Ar gas, connected to a peripheral ground chamber. The plasma oscillations observed from time-varying optical emission from the main discharge chamber show, for example, a high frequency (75.37kHz) relaxation oscillation, at 100mTorr and 8 W absorbed power,and a low frequency (2.72 Hz) relaxation oscillation, 100mTorr and 325 W absorbed power. Time-varying optical emission intensity and plasma density are also detected with a Langmuir probe. The theoretical result agrees well with experiments.

  11. Modification of the Steel Surface Treated by a Volume Discharge Plasma in Nitrogen at Atmospheric Pressure

    Science.gov (United States)

    Erofeev, M. V.; Shulepov, M. A.; Ivanov, Yu. F.; Oskomov, K. V.; Tarasenko, V. F.

    2016-03-01

    Effect of volume discharge plasma initiated by an avalanche electron beam on the composition, structure, and properties of the surface steel layer is investigated. Voltage pulses with incident wave amplitude up to 30 kV, full width at half maximum of about 4 ns, and wave front of about 2.5 ns were applied to the gap with an inhomogeneous electric field. Changes indicating the hardening effect of the volume discharge initiated by an avalanche electron beam are revealed in St3-grade steel specimens treated by the discharge of this type.

  12. Non-self-sustained discharge with hollow anode for plasma-based surface treatment

    Directory of Open Access Journals (Sweden)

    Misiruk Ivan O.

    2016-06-01

    Full Text Available The paper discusses plasma methods for surface modification using the non-self-sustained glow discharge with a hollow anode. This discharge is characterised by low voltage and high values of electron and ion currents. It can be easily excited in vacuum-arc installations that are widely used for coatings deposition. It is shown that such type of discharge may be effectively used for ion pumping, film deposition, ion etching, diffusion saturation of metallic materials, fusion and brazing of metals, and for combined application of above mentioned technologies in a single vacuum cycle.

  13. Effect of Dielectric Barrier Discharge Plasma Actuators on Non-equilibrium Hypersonic Flows

    Science.gov (United States)

    2014-10-28

    goes into the kinetic energy of the electrons rather than heating of the surrounding gas.24 The examples of these include corona discharge and micro...and S. P. Wilkinson, “Boundary layer flow control with a one atmosphere uniform glow discharge surface plasma,” AIAA Paper 98 0328, 1998. 4L. Leger, E...Moreau, G. Artana, and G. Touchard, “Influence of a DC corona discharge on the airflow along an inclined flat plate,” J. Electrostat. 51–52, 300 306

  14. Atomic and molecular processes in fusion plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Janev, R.K. [International Atomic Energy Agency, Vienna (Austria)

    1997-01-01

    The role of atomic and molecular processes in achieving and maintaining the conditions for thermonuclear burn in a magnetically confined fusion plasma is described. Emphasis is given to the energy balance and power and particle exhaust issues. The most important atomic and molecular processes which affect the radiation losses and impurity transport in the core plasma, the neutral particle transport in the plasma edge and the radiative cooling of divertor plasmas are discussed in greater detail. (author)

  15. Measurement Of Plasma Parameters In Micro-Discharge By Wall Probe

    Science.gov (United States)

    Saifutdinov, Almaz; Kudryavtsev, Anatoly; Sysoev, Sergey

    2016-09-01

    The increasing scientific and practical interest for glow discharge at high pressure is largely determined by the fact that their use does not require expensive and huge vacuum equipment. The analysis shows that, in contrast to the well-studied positive column (PC), the basic parameters of the plasma negative glow (NG) and Faraday dark space (FDS) of micro-discharges are studied insufficiently. The difficulties of the experimental diagnostics are associated with the fact that for the fixed values of pL with the increasing gas pressure the length of the micro-discharge decreases. And a small size is extremely difficult to diagnose spatial parameters distribution of micro discharges. Since at a small size introducing traditional Langmuir probe into the plasma capacity is not possible technically, it was proposed to use an additional measuring electrode (wall probe) disposed between the cathode and the anode for measurement of the fast EEDF. With its use we have registered EEDF fast electrons produced in the reaction of Penning ionization out of earlier reach range of high-pressure gas (from 20 to 200 Torr). In this paper by using wall probe we measured the basic parameters of NG plasma in micro-discharge in helium in a wide range of pressures. It is shown that the electrons temperature in the NG plasma is low and amounts to few fraction of 1 eV, which differs from the electron temperature in PC plasma. This allows the use of NG plasma for analysis by gas plasma electron spectroscopy. Authors thanks RNF (Grant 14-19-00311) for the support.

  16. Silent Discharge Plasma Technology for the Treatment of Air Toxics and Other Applications

    Energy Technology Data Exchange (ETDEWEB)

    Rosocha, Louis A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chase, Peter J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gross, Michael P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    1998-09-21

    Under this CRADA, the Los Alamos National Laboratory (LANL) and High Mesa Technologies, Inc. (HMT) carried out a joint project on the development of the silent discharge plasma (SDP) technology for the treatment of hazardous air pollutants and other hazardous or toxic chemicals. The project had two major components: a technology-demonstration part and a scale-up and commercialization part. In the first part, a small-scale, mobile SDP plasma processor, which was being developed under a CRADA with the Electric Power Research Institute (EPRI) was the mobile equipment was modified for higher capacity service and employed for an innovative remediation technologies demonstration on soil-vapor extraction off-gases at the McClellan Air Force Base near Sacramento, CA. The performance of the SDP system for the variety of volatile organic compounds (VOCs) encountered at the McClellan site was sufficiently promising to the project HMT and LANL worked together to formulate a scale-up strategy and commercialization/manufacturing plan, and to design a prototype scaled-up SDP unit. HMT and LANL are now in the final stages of completing a licensing agreement for the technology and HMT is in the process of raising funds to engineer and manufacture commercial prototype SDP equipment focused on stack-gas emissions control and environmental remediation. HMT, in collaboration with another Northern New Mexico business, Coyote Aerospace, has also been successful in receiving a Phase I Small Business Innovative Research (SBIR) award from the Army Research Office to develop, design, and construct a small non-thermal plasma reactor for laboratory studies ("Non-Thermal Plasma Reactor for Control of Fugitive Emissions of Toxic Gases")

  17. Etching of UO{sub 2} in NF{sub 3} RF Plasma Glow Discharge

    Energy Technology Data Exchange (ETDEWEB)

    John M. Veilleux

    1999-08-01

    A series of room temperature, low pressure (10.8 to 40 Pa), low power (25 to 210 W) RF plasma glow discharge experiments with UO{sub 2} were conducted to demonstrate that plasma treatment is a viable method for decontaminating UO{sub 2} from stainless steel substrates. Experiments were conducted using NF{sub 3} gas to decontaminate depleted uranium dioxide from stainless-steel substrates. Depleted UO{sub 2} samples each containing 129.4 Bq were prepared from 100 microliter solutions of uranyl nitrate hexahydrate solution. The amorphous UO{sub 2} in the samples had a relatively low density of 4.8 gm/cm{sub 3}. Counting of the depleted UO{sub 2} on the substrate following plasma immersion was performed using liquid scintillation counting with alpha/beta discrimination due to the presence of confounding beta emitting daughter products, {sup 234}Th and {sup 234}Pa. The alpha emission peak from each sample was integrated using a gaussian and first order polynomial fit to improve quantification. The uncertainties in the experimental measurement of the etched material were estimated at about {+-} 2%. Results demonstrated that UO{sub 2} can be completely removed from stainless-steel substrates after several minutes processing at under 200 W. At 180 W and 32.7 Pa gas pressure, over 99% of all UO{sub 2} in the samples was removed in just 17 minutes. The initial etch rate in the experiments ranged from 0.2 to 7.4 {micro}m/min. Etching increased with the plasma absorbed power and feed gas pressure in the range of 10.8 to 40 Pa. A different pressure effect on UO{sub 2} etching was also noted below 50 W in which etching increased up to a maximum pressure, {approximately}23 Pa, then decreased with further increases in pressure.

  18. Effects of Boundary Layer Flow Control Using Plasma Actuator Discharges

    Science.gov (United States)

    2005-09-01

    have run tests in this area to demonstrate plasma actuators as ailerons and winglets , as well as to reduce separation on low pressure turbine (LPT...ray component of the SEM computed the elemental composition percentages of the plate. For aluminum oxide, a 3-to-2 ratio of oxygen to aluminum was...desired. However, the electron microscopy revealed that manganese was present in the composition , due to impurities in the aluminum. Figure 13

  19. Numerical Modeling of the Atmospheric-Pressure Helium Plasma Formed During Spark-to-Glow Discharge Transition

    Science.gov (United States)

    Demkin, V. P.; Melnichuk, S. V.

    2017-06-01

    Results of numerical experiment on modeling of the atmospheric-pressure plasma formed during the spark-to-glow discharge transition in helium in low-current non-stationary plasmatron are presented. The numerical experiment is performed using the developed 2D physical and mathematical plasma model in the drift-diffusion approximation. Results of numerical calculation of the dynamics of discharge evolution are confirmed by the experimental data on the atmospheric-pressure plasma dynamics formed in the plasmatron during the spark-to-glow discharge transition. It is demonstrated that with preset initial conditions characteristic for spark breakdown, further discharge evolution leads to the formation of the near-cathode zone of the potential drop and the pulsed behavior of the electric current of the discharge. After the current pulse, the discharge transforms into the quasi-stationary mode with parameters characteristic for the glow discharge with monotonically increasing electric current and transverse dimensions of the plasma column.

  20. Streptococci biofilm decontamination on teeth by low-temperature air plasma of dc corona discharges

    Science.gov (United States)

    Kovalóvá, Z.; Zahoran, M.; Zahoranová, A.; Machala, Z.

    2014-06-01

    Non-thermal plasmas of atmospheric pressure air direct current corona discharges were investigated for potential applications in dental medicine. The objective of this ex vivo study was to apply cold plasmas for the decontamination of Streptococci biofilm grown on extracted human teeth, and to estimate their antimicrobial efficiency and the plasma's impact on the enamel and dentine of the treated tooth surfaces. The results show that both positive streamer and negative Trichel pulse coronas can reduce bacterial population in the biofilm by up to 3 logs in a 10 min exposure time. This bactericidal effect can be reached faster (within 5 min) by electrostatic spraying of water through the discharge onto the treated tooth surface. Examination of the tooth surface after plasma exposure by infrared spectroscopy and scanning electron microscopy did not show any significant alteration in the tooth material composition or the tooth surface structures.

  1. Plasma Kinetics in the Ethanol/Water/Air Mixture in "Tornado" Type Electrical Discharge

    CERN Document Server

    Levko, D; Chernyak, V; Olszewski, S; Nedybaliuk, O

    2011-01-01

    This paper presents the results of a theoretical and experimental study of plasma-assisted reforming of ethanol into molecular hydrogen in a new modification of the "tornado" type electrical discharge. Numerical modeling clarifies the nature of the non-thermal conversion and explains the kinetic mechanism of nonequilibrium plasma-chemical transformations in the gas-liquid system and the evolution of hydrogen during the reforming as a function of discharge parameters and ethanol-to-water ratio in the mixture. We also propose a scheme of chemical reactions for plasma kinetics description. It is shown that some characteristics of the investigated reactor are at least not inferior to characteristics of other plasma chemical reactors.

  2. Microsecond-pulsed dielectric barrier discharge plasma stimulation of tissue macrophages for treatment of peripheral vascular disease

    Science.gov (United States)

    Miller, V.; Lin, A.; Kako, F.; Gabunia, K.; Kelemen, S.; Brettschneider, J.; Fridman, G.; Fridman, A.; Autieri, M.

    2015-12-01

    Angiogenesis is the formation of new blood vessels from pre-existing vessels and normally occurs during the process of inflammatory reactions, wound healing, tissue repair, and restoration of blood flow after injury or insult. Stimulation of angiogenesis is a promising and an important step in the treatment of peripheral artery disease. Reactive oxygen species have been shown to be involved in stimulation of this process. For this reason, we have developed and validated a non-equilibrium atmospheric temperature and pressure short-pulsed dielectric barrier discharge plasma system, which can non-destructively generate reactive oxygen species and other active species at the surface of the tissue being treated. We show that this plasma treatment stimulates the production of vascular endothelial growth factor, matrix metalloproteinase-9, and CXCL 1 that in turn induces angiogenesis in mouse aortic rings in vitro. This effect may be mediated by the direct effect of plasma generated reactive oxygen species on tissue.

  3. Microsecond-pulsed dielectric barrier discharge plasma stimulation of tissue macrophages for treatment of peripheral vascular disease

    Energy Technology Data Exchange (ETDEWEB)

    Miller, V., E-mail: vmiller@coe.drexel.edu; Lin, A.; Brettschneider, J.; Fridman, G.; Fridman, A. [AJ Drexel Plasma Institute, Drexel University, Camden, New Jersey 08103 (United States); Kako, F.; Gabunia, K.; Kelemen, S.; Autieri, M. [Department of Physiology, Independence Blue Cross Cardiovascular Research Center, Temple University School of Medicine, Philadelphia, Pennsylvania 19140 (United States)

    2015-12-15

    Angiogenesis is the formation of new blood vessels from pre-existing vessels and normally occurs during the process of inflammatory reactions, wound healing, tissue repair, and restoration of blood flow after injury or insult. Stimulation of angiogenesis is a promising and an important step in the treatment of peripheral artery disease. Reactive oxygen species have been shown to be involved in stimulation of this process. For this reason, we have developed and validated a non-equilibrium atmospheric temperature and pressure short-pulsed dielectric barrier discharge plasma system, which can non-destructively generate reactive oxygen species and other active species at the surface of the tissue being treated. We show that this plasma treatment stimulates the production of vascular endothelial growth factor, matrix metalloproteinase-9, and CXCL 1 that in turn induces angiogenesis in mouse aortic rings in vitro. This effect may be mediated by the direct effect of plasma generated reactive oxygen species on tissue.

  4. Two-stage plasma gun based on a gas discharge with a self-heating hollow emitter.

    Science.gov (United States)

    Vizir, A V; Tyunkov, A V; Shandrikov, M V; Oks, E M

    2010-02-01

    The paper presents the results of tests of a new compact two-stage bulk gas plasma gun. The plasma gun is based on a nonself-sustained gas discharge with an electron emitter based on a discharge with a self-heating hollow cathode. The operating characteristics of the plasma gun are investigated. The discharge system makes it possible to produce uniform and stable gas plasma in the dc mode with a plasma density up to 3x10(9) cm(-3) at an operating gas pressure in the vacuum chamber of less than 2x10(-2) Pa. The device features high power efficiency, design simplicity, and compactness.

  5. Emission characteristics and electron kinetic coefficients of the plasma of a transverse volume discharge initiated in a mixture of heavy inert gases with chlorine molecules

    Science.gov (United States)

    Shuaibov, A. K.; Chygin, V. I.; Shimon, L. L.; Shevera, I. V.; Gorun, P. P.; Obukhovskii, R. O.

    2010-05-01

    The results of studying the radiation due to argon, krypton, and xenon monochloride bands, as well as to the bands of chlorine molecules, from the plasma of a transverse Ar-Kr-Xe-Cl2 volume discharge are reported. The working mixture of a pulse radiation source is optimized with regard to its pressure and elemental composition and parameters of an excitation system. By numerically solving the Boltzmann kinetic equation for the electron energy distribution function, the transport characteristics of plasma electrons and discharge power specific losses are found for different values of the reduced electric field strength. The plasma parameters are simulated for the quaternary mixture, which is most appropriate for a multiwave UV-VUV source. Qualitative analysis is conducted for the most important electron processes in the multicomponent plasma that govern the joint formation of argon, krypton, and xenon monochlorides in the transverse discharge.

  6. Plasma process control for improved PEO coatings on magnesium alloys

    Science.gov (United States)

    Hussein, Riyad Omran

    Plasma Electrolytic Oxidation (PEO) is a high voltage plasma-assisted oxidation process uses an environmentally-friendly aqueous electrolyte to oxidize the metal surfaces to form ceramic oxide coatings which impart a high corrosion and wear resistance. One of the main advantages of PEO process is that it can be applied to treat samples with complex shapes, and surfaces with different composition and microstructure. The PEO process of Mg alloys is strongly influenced by such parameters as electrolyte composition and concentration, current or voltage applied and substrate alloy. Generally, these parameters have a direct influence on the discharging behavior. The discharges play an essential role in the formation and resulting composition of the 3-layer oxide structure. A detailed knowledge of the coating mechanisms is extremely important in order to produce a desired coating quality to reach the best performance of the PEO coatings in terms of corrosion resistance and tribological properties (wear rate, COF). During PEO processing of magnesium, some of the metal cations are transferred outwards from the substrate and react with anions to form ceramic coatings. Also, due to the high electric field in the discharge channels, oxygen anions transfer towards the magnesium substrate and react with Mg2+ cations to form a ceramic coating. Although, in general, PEO coating of Mg alloys produces the three-layered structure, the relative proportions of the three-layers are strongly influenced by the PEO processing parameters. In PEO process, the ceramic coating grows inwards to the alloy substrate and outwards to the coating surface simultaneously. For the coating growth, there are three simultaneous processes taking place, namely the electrochemical, the plasma chemical reactions and thermal diffusion. Optical emission spectroscopy (OES) was employed for the discharge characterization by following the substrate and electrolyte element present in the plasma discharge during the

  7. Partial Oxidation of Methane with Sol-Gel Fe/Hf/YSZ Catalyst in Dielectric Barrier Discharge: Catalyst Activation by Plasma

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A 1% Fe-30% Hf over yttria-stabilized zirconia catalyst in combination with novel plasma-assisted activation techniques for a direct partial oxidation of methane to methanol was tested using dielectric barrier discharge plasma at ambient temperature and atmospheric pressure. However, instead of methanol, the reaction products were dominated by H2,CO, CO2, C2, and H2O. A catalytically activated plasma process increased the production of methanol compared with a noncatalytic plasma process. The maximum selectivity of methanol production was achieved using a catalyst that was treated at higher applied power.

  8. Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis

    Directory of Open Access Journals (Sweden)

    Grzegorz Raniszewski

    2017-02-01

    Full Text Available One of the most common methods of carbon nanotubes (CNTs synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon–plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs. It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented.

  9. Experimental investigations of the plasma radial uniformity in single and dual frequency capacitively coupled argon discharges

    Science.gov (United States)

    Zhao, Kai; Liu, Yong-Xin; Gao, Fei; Liu, Gang-Hu; Han, Dao-Man; Wang, You-Nian

    2016-12-01

    In the current work, the radial plasma density has been measured by utilizing a floating double probe in single and dual frequency capacitively coupled argon discharges operated in a cylindrical reactor, aiming at a better understanding of electromagnetic effects and exploring a method of improving the radial uniformity. The experimental results indicate that for single-frequency plasma sustained at low pressure, the plasma density radial profile exhibits a parabolic distribution at 90 MHz, whereas at 180 MHz, the profile evolves into a bimodal distribution, and both cases indicate poor uniformities. With increasing the pressure, the plasma radial uniformity becomes better for both driving frequency cases. By contrast, when discharges are excited by two frequencies (i.e., 90 + 180 MHz), the plasma radial profile is simultaneously influenced by both sources. It is found that by adjusting the low-frequency to high-frequency voltage amplitude ratio β, the radial profile of plasma density could be controlled and optimized for a wide pressure range. To gain a better plasma uniformity, it is necessary to consider the balance between the standing wave effect, which leads to a maximum plasma density at the reactor center, and the edge field effect, which is responsible for a maximum density near the radial electrode edge. This balance can be controlled either by selecting a proper gas pressure or by adjusting the ratio β.

  10. Influence of discharge and jet flow coupling on atmospheric pressure plasma homogeneity

    Science.gov (United States)

    Nizard, H.; Gaudy, T.; Toutant, A.; Iacono, J.; Descamps, P.; Leempoel, P.; Massines, F.

    2015-10-01

    The effect of flow dynamics on the discharge mode is studied in order to design a technical solution for thin film coating on large surfaces. The configuration consists in two atmospheric pressure helium plasma jets impacting a surface and confined in a tube. This system operates in open air. It has been studied by short exposure time pictures, current and voltage measurements, optical emission spectroscopy, schlieren flow visualization and computational fluid dynamics. Two discharge regimes directly connected to the gas flow dynamic have been pointed out. One is localized from the point electrodes to the surface; the other one entirely fills the confinement tube. A correlation between air intake inside the confinement tube and the discharge mode has been highlighted. Indeed, the discharge only develops in helium and the air intake confines the helium jets in volumes smaller than the confinement tube. The air intake is determined by the gas flow rate and the distance from the tube bottom to the substrate surface, parameters which have been linked to the change from laminar to turbulent flow. Finally, the understanding of flow dynamics and discharge plasma coupling allowed the design of a technical solution favoring plasma homogeneity for large surface treatment.

  11. Modeling plasma glow discharges in Air near a Mach 3 bow shock with KRONOS

    Science.gov (United States)

    Rassou, Sebastien; Labaune, Julien; Packan, Denis; Elias, Paul-Quentin

    2016-09-01

    In this work, plasma glow discharge in Air is modeled near a Mach 3 bow shock. Numerical simulations are performed using the coupling KRONOS which have been developed at ONERA. The flow field is modeled using the code CFD: CEDRE from ONERA and the electrical and plasma part by the EDF open-source code CODE_SATURNE. The plasma kinetic modeling consists on a two-term Boltzmann equation solver and a chemical reaction solver depending of the electric field. The coupling KRONOS is fully parallelized and run on ONERA supercomputers. The shock wave is formed by the propagation of a supersonic flow (M = 3) through a truncated conical model mounted with a central spike. Depending on the spike's voltage value, corona, glow or arc regime could be obtained in a steady flow. The parameters for the supersonic flow and the spike configurations are chosen to be in glow discharge regime and to reproduce the experimental setup. In our simulations, 12 species and 80 reactions (ionization, electronic or vibrational excitation, attachment etc ...) are considered to properly model the glow discharge and the afterglow. In a stationary flow, glow discharge is observed only at the upstream of the shock wave near the high voltage spike. Behind the bow shock, in the afterglow, negative ions are provided by electrons attachment with O2. The negative ions flow convection ensures the electrical conduction and the establishment of the glow discharge.

  12. Alternating current-generated plasma discharges for the controlled direct current charging of ferroelectrets

    Science.gov (United States)

    Cury Basso, Heitor; Monteiro, José Roberto B. de A.; Baladelli Mazulquim, Daniel; Teixeira de Paula, Geyverson; Gonçalves Neto, Luiz; Gerhard, Reimund

    2013-09-01

    The standard charging process for polymer ferroelectrets, e.g., from polypropylene foams or layered film systems involves the application of high DC fields either to metal electrodes or via a corona discharge. In this often-used process, the DC field triggers the internal breakdown and limits the final charge densities inside the ferroelectret cavities and, thus, the final polarization. Here, an AC + DC charging procedure is proposed and demonstrated in which a high-voltage high-frequency (HV-HF) wave train is applied together with a DC poling voltage. Thus, the internal dielectric-barrier discharges in the ferroelectret cavities are induced by the HV-HF wave train, while the final charge and polarization level is controlled separately through the applied DC voltage. In the new process, the frequency and the amplitude of the HV-HF wave train must be kept within critical boundaries that are closely related to the characteristics of the respective ferroelectrets. The charging method has been tested and investigated on a fluoropolymer-film system with a single well-defined cylindrical cavity. It is found that the internal electrical polarization of the cavity can be easily controlled and increases linearly with the applied DC voltage up to the breakdown voltage of the cavity. In the standard charging method, however, the DC voltage would have to be chosen above the respective breakdown voltage. With the new method, control of the HV-HF wave-train duration prevents a plasma-induced deterioration of the polymer surfaces inside the cavities. It is observed that the frequency of the HV-HF wave train during ferroelectret charging and the temperature applied during poling of ferroelectrics serve an analogous purpose. The analogy and the similarities between the proposed ferroelectret charging method and the poling of ferroelectric materials or dipole electrets at elevated temperatures with subsequent cooling under field are discussed.

  13. Validation of numerical codes for the analysis of plasma discharges

    Energy Technology Data Exchange (ETDEWEB)

    Albanese, R. (Univ. di Salerno, Dipt. di Ingegneria Elettronica, Fisciano (Italy)); Bottura, L. (NET Team, Garching (Germany)); Chiocchio, S. (NET Team, Garching (Germany)); Coccorese, E. (Univ. di Reggio Calabria, Ist. di Ingegneria Elettronica (Italy)); Gernhardt, J. (Max Planck IPP, Garching (Germany)); Gruber, O. (Max Planck IPP, Garching (Germany)); Fresa, R. (Univ. di Salerno, Dipt. di Ingegneria Elettronica, Fisciano (Italy)); Martone, R. (Univ. di Salerno, Dipt. di Ingegneria Elettronica, Fisciano (Italy)); Portone, A. (NET Team, Garching (Germany)); Seidel, U. (Max Planck IPP, Garching (Germany))

    1994-01-01

    Electromagnetic aspects in the design of ITER-like reactors call for an extensive use of complex and advanced numerical codes. For this reason a strong attention has been paid within the NET-Team to the code development. In particular, through a cooperation with some Italian universities, during the last years a number of numerical procedures were developed and integrated. In order to assess the code reliability and to gain confidence on their predictions for next generation ITER-like reactors, the validation of the codes against experiments has to be considered as a strict requirement. Aim of this paper is to give a comprehensive presentation of this problem in the light of the results of a campaign of validation runs. The main outcome of this work is that the computational procedures, which have been developed for the NET project and then extensively used also for ITER studies, can be considered as experimentally validated in a sufficiently wide range of cases of interest. In particular, computed values are compared with experimental measurements made during some typical ASDEX-Upgrade discharges. From the electromagnetic point of view, many features of this machine are common to the ITER concept, so that the results of the validation can reasonably be extended to the ITER case. (orig.)

  14. Energy deposition characteristics of nanosecond dielectric barrier discharge plasma actuators: Influence of dielectric material

    NARCIS (Netherlands)

    Correale, G.; Winkel, R.; Kotsonis, M.

    2015-01-01

    An experimental study aimed at the characterization of energy deposition of nanosecond Dielectric Barrier Discharge (ns-DBD) plasma actuators was carried out. Special attention was given on the effect of the thickness and material used for dielectric barrier. The selected materials for this study we

  15. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    NARCIS (Netherlands)

    Zhu, J.; Gao, J.; Ehn, A.; Alden, M.; Li, Z.; Moseev, D.; Kusano, Y.; Salewski, M.; Alpers, A.; Gritzmann, P.; Schwenk, M.

    2015-01-01

    A non-thermal gliding arc discharge was generated at atmospheric pressure in an air flow. The dynamics of the plasma column and tracer particles were recorded using two synchronized highspeed cameras. Whereas the data analysis for such systems has previously been performed in 2D (analyzing the singl

  16. Method of preparing water purification membranes. [polymerization of allyl amine as thin films in plasma discharge

    Science.gov (United States)

    Hollahan, J. R.; Wydeven, T. J., Jr. (Inventor)

    1974-01-01

    Allyl amine and chemically related compounds are polymerized as thin films in the presence of a plasma discharge. The monomer compound can be polymerized by itself or in the presence of an additive gas to promote polymerization and act as a carrier. The polymerized films thus produced show outstanding advantages when used as reverse osmosis membranes.

  17. A Study on Water Treatment Induced by Plasma with Contact Glow Discharge Electrolysis

    Institute of Scientific and Technical Information of China (English)

    胡中爱; 王晓艳; 高锦章; 邓华陵; 侯经国; 卢小泉; 康敬万

    2001-01-01

    Oxidative degradation of eight kinds of dyes induced by plasma in aqueous solution was investigated with contact glow discharge electrolysis (CGDE). It has been demonstrated that these eight dyes underwent degradation in CGDE, where Fe2+ could be utilised to raise the efficiency of degradation of dyes.

  18. Rotating plasma structures in the cross-field discharge of Hall thrusters

    Science.gov (United States)

    Mazouffre, Stephane; Grimaud, Lou; Tsikata, Sedina; Matyash, Konstantin

    2016-09-01

    Rotating plasma structures, also termed rotating spokes, are observed in various types of low-pressure discharges with crossed electric and magnetic field configurations, such as Penning sources, magnetron discharges, negative ion sources and Hall thrusters. Such structures correspond to large-scale high-density plasma blocks that rotate in the E×B drift direction with a typical frequency on the order of a few kHz. Although such structures have been extensively studied in many communities, the mechanism at their origin and their role in electron transport across the magnetic field remain unknown. Here, we will present insights into the nature of spokes, gained from a combination of experiments and advanced particle-in-cell numerical simulations that aim at better understanding the physics and the impact of rotating plasma structures in the ExB discharge of the Hall thruster. As rotating spokes appear in the ionization region of such thrusters, and are therefore difficult to probe with diagnostics, experiments have been performed with a wall-less Hall thruster. In this configuration, the entire plasma discharge is pushed outside the dielectric cavity, through which the gas is injected, using the combination of specific magnetic field topology with appropriate anode geometry.

  19. Physical and chemical properties of dust produced in a N2-CH4 RF plasma discharge

    Science.gov (United States)

    Ouni, F.; Adande, G.; Thissen, R.; Alcouffe, G.; Szopa, C.; Schmitz-Afonso, I.; Laprévote, O.; Quirico, E.; Brissaud, O.; Carrasco, N.; Cernogora, G.

    2008-09-01

    Titan's atmospheric chemistry is simulated using a Capacitively Coupled Plasma discharge produced in a N2-CH4 mixture. The produced solid particles are analysed ex-situ. Chemical properties are deduced from: elemental composition, FTIR and LTQ-Orbitrap mass spectrometer. Optical properties are deduced from reflectivity in visible and IR range.

  20. Supersonic flow of a nonequilibrium gas-discharge plasma around a body

    Science.gov (United States)

    Lapushkina, T. A.; Erofeev, A. V.; Ponyaev, S. A.; Bobashev, S. V.

    2009-06-01

    The flow of a nonequilibrium gas-discharge plasma around a semicylindrical body is studied. The aim of the study is to see how a change in the degree of nonequilibrium of the incoming plasma changes the separation distance between a shock wave and the body. Experiments are carried out with a supersonic nozzle into which a semicylindrical body is placed. The inlet of the nozzle is connected to a shock tube. In the course of the experiment, electrodes built into the wall of the nozzle initiate a gas discharge in front of the body to produce an additional nonequilibrium ionization in the stationary incoming supersonic flow. The discharge parameters are selected such that the discharge raises the electron temperature and still minimizes heating of the gas. The degree of nonequilibrium of the flow varies with gas-discharge current. Diagnostics of the flow is carried out with a schlieren system based on a semiconductor laser. The system can record flow patterns at definite time instants after discharge initiation.

  1. Charging of dust grains in a nonequilibrium plasma of a stratified glow discharge

    Science.gov (United States)

    Sukhinin, G. I.; Fedoseev, A. V.

    2007-12-01

    A theoretical model is presented that describes the charging of dust grains in the positive plasma column of a stratified glow dc discharge in argon. A one-dimensional self-consistent model is used to obtain axial profiles of the electric field, as well as the electron energy distribution function along the axis of the discharge tube. Radial profiles of the electric field are determined in the ambipolar diffusion approximation. It is assumed that, in the radial direction, the electron distribution function depends only on the total electron energy. Two-dimensional distributions of the discharge plasma parameters are calculated and used to determine the potential and charge of a test dust grain at a certain point within the discharge and the electrostatic forces acting on it. It is shown that the grain charge distribution depends strongly on the nonequilibrium electron distribution function and on the nonuniform distribution of the electric field in a stratified glow discharge. A discussion is presented on the suspension of dust grains, the separation of grains by size in the discharge striations, and a possible mechanism for the onset of vortex dust motion at the edge of a dust cloud.

  2. Investigation of complexity dynamics in a DC glow discharge magnetized plasma using recurrence quantification analysis

    Energy Technology Data Exchange (ETDEWEB)

    Mitra, Vramori; Sarma, Bornali; Sarma, Arun [VIT University, Vandalur-Kelambakkam Road, Chennai 600 127, Tamil Nadu (India); Janaki, M. S.; Sekar Iyengar, A. N. [Plasma Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700064 (India); Marwan, Norbert [Potsdam Institute for Climate Impact Research, PO Box 601203, 14412 Potsdam (Germany); Kurths, Jürgen [Potsdam Institute for Climate Impact Research, PO Box 601203, 14412 Potsdam (Germany); Institute for Complex Systems and Mathematical Biology, University of Aberdeen, Aberdeen AB24 3FX (United Kingdom)

    2016-06-15

    Recurrence is an ubiquitous feature which provides deep insights into the dynamics of real dynamical systems. A suitable tool for investigating recurrences is recurrence quantification analysis (RQA). It allows, e.g., the detection of regime transitions with respect to varying control parameters. We investigate the complexity of different coexisting nonlinear dynamical regimes of the plasma floating potential fluctuations at different magnetic fields and discharge voltages by using recurrence quantification variables, in particular, DET, L{sub max}, and Entropy. The recurrence analysis reveals that the predictability of the system strongly depends on discharge voltage. Furthermore, the persistent behaviour of the plasma time series is characterized by the Detrended fluctuation analysis technique to explore the complexity in terms of long range correlation. The enhancement of the discharge voltage at constant magnetic field increases the nonlinear correlations; hence, the complexity of the system decreases, which corroborates the RQA analysis.

  3. Radiative Characteristics of the Pulse-Periodic Discharge Plasma Initiated by Runaway Electrons

    Science.gov (United States)

    Lomaev, M. I.; Beloplotov, D. V.; Tarasenko, V. F.; Sorokin, D. A.

    2016-07-01

    Results of experimental investigations of amplitude-temporal and spectral characteristics of radiation of a pulse-periodic discharge plasma initiated in nitrogen by runaway electrons are presented. The discharge was initiated by high-voltage nanosecond voltage pulses with repetition frequency of 60 Hz in a sharply inhomogeneous electric field in a gap between the conic potential cathode and the planar grounded aluminum anode. It is established that intensive lines of Al I atoms and Al II atomic ions, lines of N I atoms and N II ions, bands of the first (1+) and second positive (2+) nitrogen systems, as well as bands of cyanogen CN are observed in the emission spectrum of the discharge plasma under the given excitation conditions.

  4. Plasma chemistry study of PLAD processes

    Energy Technology Data Exchange (ETDEWEB)

    Qin Shu; Brumfield, Kyle; Liu, Lequn Jennifer; Hu, Yongjun Jeff; McTeer, Allen; Hsu, Wei Hui; Wang Maoying [Nanya Technology Inc., Santa Clara, CA 95054 (United States); Micron Technology Inc., Boise, ID 83707 (United States)

    2012-11-06

    Plasma doping (PLAD) shows very different impurity profiles compared to the conventional beam-line-based ion implantations due to its non-mass separation property and plasma environment. There is no simulation for PLAD process so far due to a lack of a dopant profile model. Several factors determine impurity profiles of PLAD process. The most significant factors are: plasma chemistry and deposition/etching characteristics of multi-ion species plasmas. In this paper, we present plasma chemistry and deposition/etching characteristics of PLAD processes versus co-gas dilutions. Four dopant plasmas including B{sub 2}H{sub 6}, BF{sub 3}, AsH{sub 3}, and PH{sub 3}, and two non-dopant plasmas including CH{sub 4} and GeH{sub 4} are studied and demonstrated.

  5. Conversion from Dimethyl Ether to Dimethoxymethane and Dimethoxyethane Using Dielectric-Barrier Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    Wang Yu; Liu Changjun; Zhang Yueping

    2005-01-01

    Experimental investigation was conducted to convert dimethyl ether (DME) in thepresence of steam using dielectric barrier discharge (DBD) at atmospheric pressure and 373 K.The flow rate of DME was 20 ml/min. The introduction of steam resulted in an increase in theDME conversion and the selectivity of oxygenates. Plasma steam-enhanced dimethyl ether (DME)conversion led to a direct synthesis of DMMT and DMET, with a high selectivity of 5.78% and17.99%, respectively. The addition of steam promoted the formation of "plasma aerosol" that wasfavored for the formation of liquid oxygenates. The reaction pathway of plasma DME conversionwas proposed.

  6. TOPICAL REVIEW: Nucleation and aerosol processing in atmospheric pressure electrical discharges: powders production, coatings and filtration

    Science.gov (United States)

    Borra, Jean-Pascal

    2006-01-01

    This review addresses the production of nano-particles and the processing of particles injected in atmospheric pressure electrical discharges (APED). The mechanisms of formation and the evolution of particles suspended in gases are first presented, with numerical and experimental facilities. Different APED and related properties are then introduced for dc corona, streamer and spark filamentary discharges (FD), as well as for ac filamentary and homogeneous dielectric barrier discharges (DBD). Two mechanisms of particle production are depicted in APED: when FD interact with the surface of electrodes or dielectrics and when filamentary and homogeneous DBD induce reactions with gaseous precursors in volume. In both cases, condensable gaseous species are produced, leading to nano-sized particles by physical and chemical routes of nucleation. The evolution of the so-formed nano-particles, i.e. the growth by coagulation/condensation, the charging and the collection are detailed for each APED, with respect to fine powders production and thin films deposition. Finally, when particles are injected in APED, they undergo interfacial processes. Non-thermal plasmas charge particles for electro-collection and trigger heterogeneous chemical reactions for organic and inorganic films deposition. Heat exchanges in thermal plasmas enable powder purification, shaping, melting for hard coatings and fine powders production by reactive evaporation.

  7. Influence of dielectric materials on uniformity of large-area capacitively coupled plasmas for N2/Ar discharges

    Science.gov (United States)

    Liang, Ying-Shuang; Zhang, Yu-Ru; Wang, You-Nian

    2016-10-01

    The effect of the dielectric ring on the plasma radial uniformity is numerically investigated in the practical 450-mm capacitively coupled plasma reactor by a two-dimensional self-consistent fluid model. The simulations were performed for N2/Ar discharges at the pressure of 300 Pa, and the frequency of 13.56 MHz. In the practical plasma treatment process, the wafer is always surrounded by a dielectric ring, which is less studied. In this paper, the plasma characteristics are systematically investigated by changing the properties of the dielectric ring, i.e., the relative permittivity, the thickness and the length. The results indicate that the plasma parameters strongly depend on the properties of the dielectric ring. As the ratio of the thickness to the relative permittivity of the dielectric ring increases, the electric field at the wafer edge becomes weaker due to the stronger surface charging effect. This gives rise to the lower ion density, flux and N atom density at the wafer edge. Thus the homogeneous plasma density is obtained by selecting optimal dielectric ring relative permittivity and thickness. In addition, we also find that the length of the dielectric ring should be as short as possible to avoid the discontinuity of the dielectric materials, and thus obtain the large area uniform plasma. Project supported by the National Natural Science Foundation of China (Grant Nos. 11335004 and 11405019) and the Important National Science and Technology Specific Project of China (Grant No. 2011ZX02403-001).

  8. Rapid removal of bacterial endotoxin and natural organic matter in water by dielectric barrier discharge plasma: Efficiency and toxicity assessment.

    Science.gov (United States)

    Zhang, Can; Fang, Zhendong; Liu, Wenjun; Tian, Fang; Bai, Miao

    2016-11-15

    Low-temperature plasma was used to control bacteria, endotoxins and natural organic matter (NOM) in water by a dielectric barrier discharge (DBD) device. Results indicate that DBD plasma has an obvious inactivation effect on various bacteria in water. The degree of inactivation from difficult to easy is as follows: Bacillus subtilis>Escherichia coli>Staphylococcus aureus. Activated ultrapure water treated using DBD plasma exhibited a sustained sterilization effect, but this sterilization effect decreased gradually after 1h. The total-endotoxin (free-endotoxin and bound-endotoxin) released by Escherichia coli during inactivation, as well as artificially simulated endotoxin in a control solution, was significantly controlled by DBD plasma. Both the metabolites that appeared after inactivation of microorganisms by plasma treatment, and the NOM in filtration effluent of a water treatment plant were well removed by DBD plasma if the treatment duration was sufficiently long. However, the acute toxicity increased significantly, and persisted for at least 2h, indicating that some long-life active substances were generated during the DBD process. Therefore, the removal of bacteria, endotoxins or NOM does not mean a safe water is produced. It is also important to eliminate the toxicity and byproducts produced during water treatment for the continuous promotion and industrial application of DBD plasma.

  9. Effects of air transient spark discharge and helium plasma jet on water, bacteria, cells, and biomolecules.

    Science.gov (United States)

    Hensel, Karol; Kučerová, Katarína; Tarabová, Barbora; Janda, Mário; Machala, Zdenko; Sano, Kaori; Mihai, Cosmin Teodor; Ciorpac, Mitică; Gorgan, Lucian Dragos; Jijie, Roxana; Pohoata, Valentin; Topala, Ionut

    2015-06-06

    Atmospheric pressure DC-driven self-pulsing transient spark (TS) discharge operated in air and pulse-driven dielectric barrier discharge plasma jet (PJ) operated in helium in contact with water solutions were used for inducing chemical effects in water solutions, and the treatment of bacteria (Escherichia coli), mammalian cells (Vero line normal cells, HeLa line cancerous cells), deoxyribonucleic acid (dsDNA), and protein (bovine serum albumin). Two different methods of water solution supply were used in the TS: water electrode system and water spray system. The effects of both TS systems and the PJ were compared, as well as a direct exposure of the solution to the discharge with an indirect exposure to the discharge activated gas flow. The chemical analysis of water solutions was performed by using colorimetric methods of UV-VIS absorption spectrophotometry. The bactericidal effects of the discharges on bacteria were evaluated by standard microbiological plate count method. Viability, apoptosis and cell cycle were assessed in normal and cancerous cells. Viability of cells was evaluated by trypan blue exclusion test, apoptosis by Annexin V-FITC/propidium iodide assay, and cell cycle progression by propidium iodide/RNase test. The effect of the discharges on deoxyribonucleic acid and protein were evaluated by fluorescence and UV absorption spectroscopy. The results of bacterial and mammalian cell viability, apoptosis, and cell cycle clearly show that cold plasma can inactivate bacteria and selectively target cancerous cells, which is very important for possible future development of new plasma therapeutic strategies in biomedicine. The authors found that all investigated bio-effects were stronger with the air TS discharge than with the He PJ, even in indirect exposure.

  10. Microelectrical Discharge Machining: A Suitable Process for Machining Ceramics

    Directory of Open Access Journals (Sweden)

    Andreas Schubert

    2015-01-01

    Full Text Available Today ceramics are used in many industrial applications, for example, in the biomedical field, for high-temperature components or for cutting tools. This is attributed to their excellent mechanical and physical properties, as low density, high strength, and hardness or chemical resistance. However, these specific mechanical properties lead to problems regarding the postprocessing of ceramics. In particular, cutting processes require expensive tools which cause high manufacturing costs to machine ceramics. Consequently, there is a demand for alternative machining processes. Microelectrical discharge machining (micro-EDM is a thermal abrasion process which is based on electrical discharges between a tool and a workpiece. The advantages of micro-EDM are more and more in focus for ceramic machining. These advantages include the process of being a noncontact technology, an independency of material brittleness and hardness, a low impact on the material, and the achievable microstructures. This paper presents the current state of investigations regarding micro-EDM of ceramics. Beside the process principle of EDM, the used procedures for machining ceramics and insulating ceramics are described. Furthermore several machining examples are presented to demonstrate the possibilities of the micro-EDM process with regard to the machining of ceramics.

  11. Surface modification of acrylate intraocular lenses with dielectric barrier discharge plasma at atmospheric pressure

    Institute of Scientific and Technical Information of China (English)

    WANG Yao; LIU ZhenMei; XU ZhiKang; YAO Ke

    2009-01-01

    Surface modification with dielectric barrier discharge (DBD) plasma was carried out at atmospheric pressure (argon as the discharge gas) to improve the biocompatibility of hydrophobic acrylate intraocular lens (IOL). Changes of the plasma-treated IOL surface in chemical composition,morphology and hydrophilicity were comprehensively evaluated by X-ray photoelectron spectroscopy (XPS),field emission scanning electron microscopy (FESEM),atomic force microscopy (AFM) and water contact angle (WCA) measurements. The surface biocompatibility of the untreated and plasma-treated IOLs was compared with the adhesion behavior of platelets,macrophages and lens epithelial cells (LECs) in vitro. After DBD plasma treatment,the hydrophilicity of the IOL surface was obviously improved. The changes in WCA with treatment extension may be attributed to both the introduction of oxygen or/and nitrogen-containing polar groups and the increase of surface roughness induced by plasma etching effect. The existence of low molecular weight oxidized material (LMWOM) was proved on the plasma treated IOL which was caused by the chain scission effect of the plasma treatment. The plasma-treated lOLs resisted the adhesion of platelets and macrophages significantly. The LECs spreading and proliferation were postponed on the lOLs plasma-treated for more than 180 s,with a well maintained epithelial phenotype of LECs. The IOL biocompatibility was improved after the DBD plasma treatment. We speculate that slighter foreign-body reaction and later incidence of anterior capsule opacification (ACO) may be expected after implantation of the argon DBD plasma-treated IOL.

  12. Surface modification of acrylate intraocular lenses with dielectric barrier discharge plasma at atmospheric pressure

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Surface modification with dielectric barrier discharge(DBD) plasma was carried out at atmospheric pressure(argon as the discharge gas) to improve the biocompatibility of hydrophobic acrylate intraocular lens(IOL).Changes of the plasma-treated IOL surface in chemical composition,morphology and hydrophilicity were comprehensively evaluated by X-ray photoelectron spectroscopy(XPS),field emission scanning electron microscopy(FESEM),atomic force microscopy(AFM) and water contact angle(WCA) measurements.The surface biocompatibility of the untreated and plasma-treated IOLs was compared with the adhesion behavior of platelets,macrophages and lens epithelial cells(LECs) in vitro.After DBD plasma treatment,the hydrophilicity of the IOL surface was obviously improved.The changes in WCA with treatment extension may be attributed to both the introduction of oxygen or/and nitrogen-containing polar groups and the increase of surface roughness induced by plasma etching effect.The existence of low molecular weight oxidized material(LMWOM) was proved on the plasma-treated IOL which was caused by the chain scission effect of the plasma treatment.The plasma-treated IOLs resisted the adhesion of platelets and macrophages significantly.The LECs spreading and proliferation were postponed on the IOLs plasma-treated for more than 180 s,with a well maintained epithelial phenotype of LECs.The IOL biocompatibility was improved after the DBD plasma treatment.We speculate that slighter foreign-body reaction and later incidence of anterior capsule opacification(ACO) may be expected after implantation of the argon DBD plasma-treated IOL.

  13. Plasma sterilization of polyethylene terephthalate bottles by pulsed corona discharge at atmospheric pressure.

    Science.gov (United States)

    Masaoka, Satoshi

    2007-06-01

    A pulsed power supply was used to generate a corona discharge on a polyethylene terephthalate bottle, to conduct plasma sterilization at atmospheric pressure. Before generating such a discharge, minute quantities of water were attached to the inner surface of the bottle and to the surface of a high voltage (HV) electrode inserted into the bottle. Next, high-voltage pulses of electricity were discharged between electrodes for 6.0s, while rotating the bottle. The resulting spore log reduction values of Bacillus subtilis and Aspergillus niger on the inner surface of the bottle were 5.5 and 6 or higher, respectively, and those on the HV electrode surface were each 6 or higher for both strains. The presence of the by-products gaseous ozone, hydrogen peroxide, and nitric ions resulting from the electrical discharge was confirmed.

  14. Parameter optimization model in electrical discharge machining process

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and time consuming. In this paper,artificial neural network (ANN) and genetic algorithm (GA) are used together to establish the parameter optimization model. An ANN model which adapts Levenberg-Marquardt algorithm has been set up to represent the relationship between material removal rate (MRR) and input parameters, and GA is used to optimize parameters, so that optimization results are obtained. The model is shown to be effective, and MRR is improved using optimized machining parameters.

  15. Low-pressure hydrogen discharge maintenance in a large-size plasma source with localized high radio-frequency power deposition

    Energy Technology Data Exchange (ETDEWEB)

    Todorov, D.; Shivarova, A., E-mail: ashiva@phys.uni-sofia.bg; Paunska, Ts. [Faculty of Physics, Sofia University, BG-1164 Sofia (Bulgaria); Tarnev, Kh. [Department of Applied Physics, Technical University-Sofia, BG-1000 Sofia (Bulgaria)

    2015-03-15

    The development of the two-dimensional fluid-plasma model of a low-pressure hydrogen discharge, presented in the study, is regarding description of the plasma maintenance in a discharge vessel with the configuration of the SPIDER source. The SPIDER source, planned for the neutral-beam-injection plasma-heating system of ITER, is with localized high RF power deposition to its eight drivers (cylindrical-coil inductive discharges) and a large-area second chamber, common for all the drivers. The continuity equations for the charged particles (electrons and the three types of positive ions) and for the neutral species (atoms and molecules), their momentum equations, the energy balance equations for electrons, atoms and molecules and the Poisson equations are involved in the discharge description. In addition to the local processes in the plasma volume, the surface processes of particle reflection and conversion on the walls as well as for a heat exchange with the walls are included in the model. The analysis of the results stresses on the role of the fluxes (particle and energy fluxes) in the formation of the discharge structure. The conclusion is that the discharge behavior is completely obeyed to non-locality. The latter is displayed by: (i) maximum values of plasma parameters (charged particle densities and temperatures of the neutral species) outside the region of the RF power deposition, (ii) shifted maxima of the electron density and temperature, of the plasma potential and of the electron production, (iii) an electron flux, with a vortex structure, strongly exceeding the total ion flux which gives evidence of a discharge regime of non-ambipolarity and (iv) a spatial distribution of the densities of the neutral species resulting from their fluxes.

  16. Ignition and dynamics of high-voltage glow discharge plasma implantation

    Science.gov (United States)

    Fu, Ricky K. Y.; Chu, Paul K.; Tian, X. B.; Yang, S. Q.

    2006-01-01

    The self-ignition and dynamics of glow discharge plasma in the pulsed high-voltage plasma immersion ion implantation mode have been investigated. After ignition during the pulse-on period, the glow discharge continues to be sustained for a long period of time after the high-voltage pulse has been turned off as monitored by a Langmuir probe. The glow discharge and ignition lie on the left side of the Paschen curve when pd (gas pressure times electrode separation) is adjusted by using different anode to cathode distances utilizing a conducting grounded grid. The increased or constant implantation current Ia reveals that the ion sheath is stable and conforms to the cathode structure as the plasma density increases by one to two orders of magnitude towards the anode. In addition, the duration of the post-pulse-off plasma can be as long as several times of the pulse duration. The ignition time and duration of the plasma depend on the working pressure, applied voltage and pulse duration.

  17. Rice (Oryza sativa L.) Seed Sterilization and Germination Enhancement via Atmospheric Hybrid Nonthermal Discharge Plasma.

    Science.gov (United States)

    Khamsen, Natthaporn; Onwimol, Damrongvudhi; Teerakawanich, Nithiphat; Dechanupaprittha, Sanchai; Kanokbannakorn, Weerawoot; Hongesombut, Komsan; Srisonphan, Siwapon

    2016-08-01

    We designed a system to produce atmospheric hybrid cold-discharge plasma (HCP) based on microcorona discharge on a single dielectric barrier and applied it to inactivate microorganisms that commonly attach the rice seed husk. The cold-plasma treatment modified the surface of the rice seeds, resulting in accelerated germination and enhanced water imbibition. The treatment can operate under air-based ambient conditions without the need for a vacuum. The cold-plasma treatment completely inactivated pathogenic fungi and other microorganisms, enhancing the germination percentage and seedling quality. The final germination percentage of the treated rice seeds was ∼98%, whereas that of the nontreated seeds was ∼90%. Microcorona discharge on a single dielectric barrier provides a nonaggressive cold plasma that can be applied to organic materials without causing thermal and electrical damage. The hybrid nonthermal plasma is cost effective and consumes relatively little power, making it suitable for the surface sterilization and disinfection of organic and biological materials with large-scale compatibility.

  18. Non-thermal dielectric-barrier discharge plasma damages human keratinocytes by inducing oxidative stress

    Science.gov (United States)

    KIM, KI CHEON; PIAO, MEI JING; HEWAGE, SUSARA RUWAN KUMARA MADDUMA; HAN, XIA; KANG, KYOUNG AH; JO, JIN OH; MOK, YOUNG SUN; SHIN, JENNIFER H.; PARK, YEUNSOO; YOO, SUK JAE; HYUN, JIN WON

    2016-01-01

    The aim of this study was to identify the mechanisms through which dielectric-barrier discharge plasma damages human keratinocytes (HaCaT cells) through the induction of oxidative stress. For this purpose, the cells were exposed to surface dielectric-barrier discharge plasma in 70% oxygen and 30% argon. We noted that cell viability was decreased following exposure of the cells to plasma in a time-dependent manner, as shown by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay. The levels of intracellular reactive oxygen species (ROS) were determined using 2′,7′-dichlorodihydro-fluorescein diacetate and dihydroethidium was used to monitor superoxide anion production. Plasma induced the generation of ROS, including superoxide anions, hydrogen peroxide and hydroxyl radicals. N-acetyl cysteine, which is an antioxidant, prevented the decrease in cell viability caused by exposure to plasma. ROS generated by exposure to plasma resulted in damage to various cellular components, including lipid membrane peroxidation, DNA breaks and protein carbonylation, which was detected by measuring the levels of 8-isoprostane and diphenyl-1-pyrenylphosphine assay, comet assay and protein carbonyl formation. These results suggest that plasma exerts cytotoxic effects by causing oxidative stress-induced damage to cellular components. PMID:26573561

  19. Measurements of Rotational Temperatures in Atmospheric-Pressure Capillary Plasma Electrode (CPE) Discharge

    Science.gov (United States)

    Figus, Margaret; Abramzon, Nina; Becker, Kurt

    2003-10-01

    We report the results of rotational temperature measurements in atmospheric-pressure capillary plasma electrode (CPE) discharges in ambient air using the unresolved N2 second positive band. Assuming that the emitting N2 molecules can be described by a Maxwell-Boltzmann distribution characterized by a single rotational temperature, this temperature is determined from a fit of the measured emission spectrum to a calculated spectrum. If the emitting species are in equilibrium with the bulk gas in the plasma, then this temperature can be interpreted as the gas kinetic temperature in the plasma. We determined rotational temperatures for three different plasma regions: inside the capillary by analyzing radiation emitted along the axis of the capillary, between the capillaries, and perpendicular to the axis of the capillary. Each region has a different plasma density and, therefore, a different gas temperature with the plasma inside the capillary being the hottest. We also measured the rotational temperatures in each region as a function of the plasma power. As expected, the rotational temperatures increase with increasing discharge power. Work supported by the NSF and by ARO through a DURIP award.

  20. Radiofrequency antenna for suppression of parasitic discharges in a helicon plasma thruster experiment.

    Science.gov (United States)

    Takahashi, Kazunori

    2012-08-01

    A radiofrequency (rf) antenna for helicon plasma thruster experiments is developed and tested using a permanent magnets helicon plasma source immersed in a vacuum chamber. A magnetic nozzle is provided by permanent magnets arrays and an argon plasma is produced by a 13.56 MHz radiofrequency helicon-wave or inductively-coupled discharge. A parasitic discharge outside the source tube is successfully suppressed by covering the rf antenna with a ceramic ring and a grounded shield; a decrease in the ion saturation current of a Langmuir probe located outside the source tube is observed and the ion saturation current on axis increases simultaneously, compared with the case of a standard uncovered rf antenna. It is also demonstrated that the covered antenna can yield stable operation of the source.

  1. Ignition of beam plasma discharge in the electron beam experiment in space

    Science.gov (United States)

    Sasaki, S.; Kawashima, N.; Kuriki, K.; Yanagisawa, M.; Roberts, W. T.; Taylor, W. W. L.

    1985-01-01

    An ignition of beam plasma discharge (BPD) in space was observed in a neutral gas-electron beam interaction experiment by Space Shuttle/Spacelab-1 in 1983. An electron beam of 8 kV 100 mA was injected into a high dense nitrogen gas cloud of 10 to the 23rd molecules which was released during 100 msec from the Orbiter. The appearance of the beam and its surroundings observed by a low-light-level TV camera showed a local ignition of the beam plasma discharge in the gas cloud. The enhanced plasma production, generation of auroral emission, and associated wave emission were also detected by onboard diagnostic instruments.

  2. Enhancement of ZnO-Based Photocatalyst Activity by RF Discharge-Plasma Treatment*

    Science.gov (United States)

    Savastenko, N. A.; Filatov, I. I.; Lyushkevich, V. A.; Chubrik, N. I.; Gabdullin, M. T.; Ramazanov, T. S.; Abdullin, H. A.; Kalkozova, V. A.

    2016-11-01

    The structure and photocatalytic properties of polydisperse zinc oxide (ZnO) powder treated with a low-pressure radio-frequency (RF) plasma discharge were studied. The photocatalytic properties of ZnO before and after the treatment were studied with respect to photodegradation of organic impurities using decomposition of methyl orange in aqueous solution by UV light as an example. It was found that the photodegradation kinetics were described well by first-order equations. The photodegradation mechanisms of methyl orange over untreated and plasma-treated ZnO samples were different. It was shown that the effectiveness of the photodegradation expressed in terms of reaction constants increased by 20% after RF discharge-plasma treatment of the photocatalyst.

  3. An overview of CO2 conversion in a microwave discharge: the role of plasma-catalysis

    Science.gov (United States)

    Chen, Guoxing; Britun, Nikolay; Godfroid, Thomas; Georgieva, Violeta; Snyders, Rony; Delplancke-Ogletree, Marie-Paule

    2017-03-01

    An overview of the recent progress on plasma-assisted CO2 conversion in microwave discharges is given. Special attention is devoted to the results obtained using plasma catalysis, which are compared to the plasma-only CO2 decomposition cases. The effects of plasma operating conditions, catalyst preparation methods, nature of plasma activation gas, gas mixture, as well as the NiO content on the TiO2 surface on CO2 conversion and its energy efficiency are discussed. A significant improvement in CO2 conversion is obtained with a NiO/TiO2 catalyst activated in Ar plasma, when the NiO content is about 10 wt.%. The catalyst characterization data show that Ar plasma treatment results in a higher density of oxygen vacancies and a comparatively more uniform distribution of NiO on the TiO2 surface, which strongly influence CO2 conversion and its energy efficiency. The dissociative electron attachment of CO2 at the catalyst surface enhanced by the oxygen vacancies and by plasma electrons may also explain the increase in conversion and energy efficiencies. A mechanism for the plasma-catalytic CO2 conversion at the surface of an Ar plasma-threated catalyst is proposed.

  4. Modification of polylactic acid surface using RF plasma discharge with sputter deposition of a hydroxyapatite target for increased biocompatibility

    Science.gov (United States)

    Tverdokhlebov, S. I.; Bolbasov, E. N.; Shesterikov, E. V.; Antonova, L. V.; Golovkin, A. S.; Matveeva, V. G.; Petlin, D. G.; Anissimov, Y. G.

    2015-02-01

    Surface modification of polylactic acid (PLLA) by plasma of radio-frequency magnetron discharge with hydroxyapatite target sputtering was investigated. Increased biocompatibility was demonstrated using studies with bone marrow multipotent mesenchymal stromal cells. Atomic force microscopy demonstrates that the plasma treatment modifies the surface morphology of PLLA to produce rougher surface. Infrared spectroscopy and X-ray diffraction revealed that changes in the surface morphology are caused by the processes of PLLA crystallization. Fluorescent X-ray spectroscopy showed that the plasma treatment also changes the chemical composition of PLLA, enriching it with ions of the sputtered target: calcium, phosphorus and oxygen. It is hypothesized that these surface modifications increase biocompatibility of PLLA without increasing toxicity.

  5. An expression for the h l factor in low-pressure electronegative plasma discharges

    Science.gov (United States)

    Chabert, P.

    2016-04-01

    The positive ion flux exiting a low-pressure plasma discharge is a crucial quantity in global (volume-averaged) models. In discharges containing only electrons and positive ions (electropositive discharges), it is common to write this flux {Γ\\text{wall}}={{h}\\text{l}}{{n}\\text{i0}}{{u}\\text{B}} , where {{n}\\text{i0}} is the central positive ion density, {{u}\\text{B}} is the positive ion fluid speed at the sheath edge (the Bohm speed), and {{h}\\text{l}} is the positive ion edge-to-centre density ratio. There are well established formulae for {{h}\\text{l}} in electropositive discharges, but for discharges containing negative ions (electronegative discharges), the analysis is more complicated. The purpose of this paper is to propose a formula for the {{h}\\text{l}} factor in low-pressure electronegative discharges. We use the numerical solution of fluid equations with Boltzmann negative ions, including Poisson’s equation, as a guide to derive an analytical expression that can easily be incorporated in global models. The parameter space in which the derived expression is valid is discussed at the end of the paper.

  6. Investigation of Meltblown Microfiber and Electrospun Nanofiber Fabrics Treated with a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP)

    Science.gov (United States)

    Chen, Weiwei; Reece Roth, J.; Tsai, Peter P.-Y.

    2003-10-01

    Nanofiber webs are made by the electrospinning (ES) process [1], which uses the repulsive electrostatic force to spin fibers from a polymer solution or melt at room temperature and low energy input. We have developed apparatus at the UT Textiles and Nonwovens Development Center (TANDEC) to produce fabrics with fiber diameters of tens of nanometers. This paper will report data on the distribution function of nanofiber diameters that were taken from digitized SEM images of the electrospun materials. It is also found in the tensile tests that the strength of the electrospun nanofiber fabrics is up to ten times that of the coarser meltblown material. The one atmosphere uniform glow discharge plasma (OAUGDP) developed at the UT Plasma Sciences Laboratory generates a normal glow electrical discharge at one atmosphere. This plasma has been used to treat meltblown and electrospun fabrics, with a resulting increase in surface energy [1]. We recently found that the surface energy of meltblown Nylon could be increased to 70 dynes/cm by five seconds of OAUGDP exposure, and was durable at this level for six months. Our results also show that Nylon and PU nanofiber fabrics can be exposed to the OAUGDP for treatment without significant damage for up to 10 seconds [1], a duration sufficient to produce important effects, including durable wettability. We will describe our progress in improving the properties of nanofiber fabrics using a variety of latest developments in OAUGDP reactor technology, including a new porous electrode that injects gases other than air to generate different active species for plasma treatment. [1] Tsai P. P.-Y., Chen W., Li X. and Roth J.R.: "Improving the Properties of Protective Clothing by Exposing Nanofiber Webs to a One Atmospheric Uniform Glow Discharge Plasma (OAUGDP)", National Science Foundation (NSF) Grantee¡¯s Workshop and Conference, Birmingham, Alabama, Jan. 6-9, 2003.

  7. Diagnostic of the self-healing of metallized polypropylene film by modeling of the broadening emission lines of aluminum emitted by plasma discharge

    Science.gov (United States)

    Tortai, J.-H.; Bonifaci, N.; Denat, A.; Trassy, C.

    2005-03-01

    Metallized-film capacitors have the property, even under high continuous voltage, to self-heal i.e., to clear a defect in the dielectric. The self-healing process is a consequence of a transient arc discharge. It has been previously shown that during the discharge, due to Joule effect, the metal is vaporized until the arc extinguishes. The discharge duration has been found to be inversely proportional to the mechanical pressure applied on the layers of metallized films making up a capacitor. The aim of this study is to understand the physical processes involved in this spontaneous extinction of the arc discharge. Emission spectroscopy has been used to provide information about the physical properties (temperatures, electronic and neutral particles densities, etc.) of the plasma induces by a self-healing. An analysis, based on the broadenings and shifts of Al atomic lines, of the experimental light spectra obtained has shown that the self-healing process leads to the generation, from the vaporized metal, of a high-density and relatively weakly ionized aluminum plasma. The plasma density increases with the pressure applied on the film layers and, consequently, the density power needed to extend the plasma zone increases as well and the arc discharge goes out faster as experimentally observed.

  8. Decomposition of L-valine under nonthermal dielectric barrier discharge plasma.

    Science.gov (United States)

    Li, Yingying; Kojtari, Arben; Friedman, Gary; Brooks, Ari D; Fridman, Alex; Ji, Hai-Feng

    2014-02-13

    L-Valine solutions in water and phosphate buffer were treated with nonthermal plasma generated by using a dielectric barrier discharge (DBD) device and the products generated after plasma treatments were characterized by (1)H NMR and GC-MS. Our results demonstrate that L-valine is decomposed to acetone, formic acid, acetic acid, threo-methylaspartic acid, erythro-methlyaspartic acid, and pyruvic acid after direct exposure to DBD plasma. The concentrations of these compounds are time-dependent with plasma treatment. The mechanisms of L-valine under the DBD plasma are also proposed in this study. Acetone, pyruvic acid, and organic radicals (•)CHO, CH3COCH2OO(•) (acetonylperoxy), and CH3COC(OH)2OO(•) (1,1-dihydroxypropan-2-one peroxy) may be the determining chemicals in DNA damage.

  9. Development of a long pulse plasma gun discharge for magnetic turbulence studies

    Science.gov (United States)

    Schaffner, David

    2016-10-01

    A long pulse ( 300 μs) plasma gun discharge is in development at the Bryn Mawr College Plasma Laboratory for the production of sustained magnetized plasma injection for magnetohydrodynamic (MHD) turbulence studies. An array of eight 0.5mF parallel capacitors are used to create a pulse-forming-network (PFN) with a plateaued current output of 50kA for at least 200 of the 300 μs pulse. A 24cm inner diameter plasma gun provides stuffing flux fields at the stuffing threshold in order to allow for the continuous injection of magnetic helicity. Plasma is injected into a 24cm diameter flux-conserving aluminum chamber with a high density port array for fine spatial resolution diagnostic access. Fluctuations of magnetic field and saturation current are measured using pickup probes and Langmuir probes respectively.

  10. Dynamic Properties of Helium Atmospheric Dielectric-Barrier-Discharge Plasma Jet.

    Science.gov (United States)

    Uchida, Giichiro; Takenaka, Kosuke; Miyazaki, Atsushi; Kawabata, Kazufumi; Setsuhara, Yuichi

    2015-03-01

    We present here experiments on helium atmospheric dielectric-barrier discharge jet in open air. A long stable plasma plume is realized at high applied voltage and high gas flow rate. Optical emission measurements show that the plasma plume consists of two part: a plume head with high energy electrons and a tail part with low energy electrons. The plasma plume propagates away from the quartz-tube outlet with about 30-80 km/sec along the helium gas flow channel. The propagation velocity of plasma plume is in the time scale of electron drift velocity, and the electric field plays an important role as a driving force of the plasma plume propagation.

  11. Electro-Catalysis System for Biodiesel Synthesis from Palm Oil over Dielectric-Barrier Discharge Plasma Reactor

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2014-07-01

    Full Text Available Biodiesel synthesis reaction routes from palm oil using plasma electro-catalysis process over Dielectric-Barrier Discharge (DBD plasma reactor were studied. The study was focused on finding possible reaction mechanism route during plasma electro-catalysis process. The prediction was performed based on the changes of Gas Chromatography Mass Spectrometer (GC-MS and Fourier Transform Infra Red (FT-IR analyses to the biodiesel products with respect to time length of plasma treatment. It was found that main reaction mechanism occurred in the plasma electro-catalysis system was non-thermal pyrolysis rather than transesterification. The main reactions within the plasma treatment were due to collision between high energetic electrons (supplied from high voltage power supply through high voltage electrode and the reaction mixtures. The high energetic electrons affected the electrons pair of covalent bonding to be excited or dissociated even ionized at higher energy. Therefore, this plasma electro-catalysis system was promising for biodiesel synthesis from vegetable oils due to only very short time reaction was needed, even no need a catalyst, no soap formation, and no glycerol by-product. This system could produce fatty acid methyl ester yield of 75.65% at 120 seconds and other possible chemicals, such as alkynes, alkanes, esters, carboxylic acid, and aldehydes. However, during the plasma process, the reaction mechanisms were still difficult to be controlled due the action of available high energetic electrons. The advanced studies on how to control the reaction mechanism selectively in the plasma electro-catalysis will be published elsewhere. © 2014 BCREC UNDIP. All rights reservedReceived: 23rd January 2014; Revised: 20th March 2014; Accepted: 23rd March 2014[How to Cite: Istadi, I., Yudhistira, A.D., Anggoro, D.D., Buchori, L. (2014. Electro-Catalysis System for Biodiesel Synthesis from Palm Oil over Dielectric-Barrier Discharge Plasma Reactor

  12. Potential of electric discharge plasma methods in abatement of volatile organic compounds originating from the food industry.

    Science.gov (United States)

    Preis, S; Klauson, D; Gregor, A

    2013-01-15

    Increased volatile organic compounds emissions and commensurate tightening of applicable legislation mean that the development and application of effective, cost-efficient abatement methods are areas of growing concern. This paper reviews the last two decades' publications on organic vapour emissions from food processing, their sources, impacts and treatment methods. An overview of the latest developments in conventional air treatment methods is presented, followed by the main focus of the paper, non-thermal plasma technology. The results of the review suggest that non-thermal plasma technology, in its pulsed corona discharge configuration, is an emerging treatment method with potential for low-cost, effective abatement of a wide spectrum of organic air pollutants. It is found that the combination of plasma treatment with catalysis is a development trend that demonstrates considerable potential. The as yet relatively small number of plasma treatment applications is considered to be due to the novelty of pulsed electric discharge techniques and a lack of reliable pulse generators and reactors. Other issues acting as barriers to widespread adoption of the technique include the possible formation of stable oxidation by-products, residual ozone and nitrogen oxides, and sensitivity towards air humidity.

  13. Social Work Discharge Planning in Acute Care Hospitals in Israel: Clients' Evaluation of the Discharge Planning Process and Adequacy

    Science.gov (United States)

    Soskolne, Varda; Kaplan, Giora; Ben-Shahar, Ilana; Stanger, Varda; Auslander, Gail. K.

    2010-01-01

    Objective: To examine the associations of patients' characteristics, hospitalization factors, and the patients' or family assessment of the discharge planning process, with their evaluation of adequacy of the discharge plan. Method: A prospective study. Social workers from 11 acute care hospitals in Israel provided data on 1426 discharged…

  14. Social Work Discharge Planning in Acute Care Hospitals in Israel: Clients' Evaluation of the Discharge Planning Process and Adequacy

    Science.gov (United States)

    Soskolne, Varda; Kaplan, Giora; Ben-Shahar, Ilana; Stanger, Varda; Auslander, Gail. K.

    2010-01-01

    Objective: To examine the associations of patients' characteristics, hospitalization factors, and the patients' or family assessment of the discharge planning process, with their evaluation of adequacy of the discharge plan. Method: A prospective study. Social workers from 11 acute care hospitals in Israel provided data on 1426 discharged…

  15. Charge-discharge process of MnO2 supercapacitor

    Institute of Scientific and Technical Information of China (English)

    LIU Kai-yu; ZHANG Ying; ZHANG Wei; ZHENG He; SU Geng

    2007-01-01

    Mechanochemical synthesis of α-MnO2 was carried out with KMnO4 and Mn(CH3COO)2 in 1-1 mole ratio. The electrochemical performance of MnO2 electrode was investigated by cyclic voltammograms and alternating current impedance. The charge-discharge process of MnO2 supercapacitor in 6 mol/L KOH was studied within 1.2 V at 200 mA/g, suggesting that it displays double-layer capacibility in low potential scope and pseudo-capacitance properties in high potential scope. It is found that Mn3O4, an electrochemical inert, mainly forms in the initial 40 charge-discharge cycles. During cycling, the pseudo-capacitance properties disappear and the discharge curves are close to ideal ones, indicating double-layer capability. The maximum capacitance of MnO2 electrode is as high as 416 F/g, and retains 240 F/g after 200 cycles. The equivalent series resistance increases from 17 to 41 Ω.

  16. Cold plasma processing to improve food safety

    Science.gov (United States)

    Cold plasma is an antimicrobial process being developed for application as a food processing technology. This novel intervention is the subject of an expanding research effort by groups around the world. A variety of devices can be used to generate cold plasma and apply it to the food commodity bein...

  17. Low-temperature NOx reduction processes using combined systems of pulsed corona discharge and catalysts

    Science.gov (United States)

    Kim, H. H.; Takashima, K.; Katsura, S.; Mizuno, A.

    2001-02-01

    In this paper, we will report NOx removal via reduction processes using two types of combined system of pulse corona discharge and catalysts: the single-stage plasma-driven catalyst (PDC) system, and the two-stage plasma-enhanced selective catalytic reduction (PE-SCR) system. Several catalysts, such as γ-alumina catalysts, mechanically mixed catalysts of γ-alumina with BaTiO3 or TiO2, and Co-ZSM-5 were tested. In the PDC system, which is directly activated by the discharge plasma, it was found that the use of additives was necessary to achieve NOx removal by reduction. Removal rates of NO and NOx were linearly increased as the molar ratio of additive to NOx increased. The dependence of NO and NOx removal on the gas hourly space velocity (GHSV) at a fixed specific input energy (SIE) indicates that plasma-induced surface reaction on the catalyst plays an important role in the PDC system. It was found that the optimal GHSV of the PDC system with the γ-alumina catalyst was smaller than 6000 h-1. Mechanical mixing of γ-alumina with BaTiO3 or TiO2 did not enhance NO and NOx removal and γ-alumina alone was found to be the most suitable catalyst. The dielectric constant of the catalyst only influenced the plasma intensity, not the NOx removal. In the PE-SCR system, plasma-treated NOx (mostly NO2) was reduced effectively with NH3 over the Co-ZSM-5 catalyst at a relatively low temperature of 150 °C. Under optimal conditions the energy cost and energy yield were 25 eV/molecule and 21 g-N (kWh)-1, respectively.

  18. Controlled cytotoxicity of plasma treated water formulated by open-air hybrid mode discharge

    Science.gov (United States)

    Lu, P.; Boehm, D.; Cullen, P.; Bourke, P.

    2017-06-01

    Plasma treated liquids (PTLs) provide a means to convey a broad range of effects of relevance for food, environmental, or clinical decontamination, plant growth promotion, and therapeutic applications. Devising the reactive species ingredients and controlling the biological response of PTLs are of great interest. We demonstrate an approach by using an open-air hybrid mode discharge (HMD) to control the principal reactive species composition within plasma treated water (PTW), which is then demonstrated to regulate the cytotoxicity of PTW. The cytotoxicity of HMD produced PTW demonstrates a non-monotonic change over the discharge time. Although hydrogen peroxide and nitrite are not the sole effectors for cell death caused by PTW, using them as principal reactive species indicators, cytotoxicity can be removed and/or enhanced by formulating their concentrations and composition through adjusting the discharge mode and time on-line during PTW generation without the addition of additional working gas or chemical scavengers. This work demonstrates that a hybrid mode discharge can be employed to generate a PTW formulation to control a biological response such as cytotoxicity. This provides insights into how plasma treated liquids may be harnessed for biological applications in a specific and controllable manner.

  19. Study on the Generation Characteristics of Dielectric Barrier Discharge Plasmas on Water Surface

    Science.gov (United States)

    Liu, Wenzheng; Li, Chuanhui

    2014-01-01

    A new contact glow discharge electrode on the surface of water was designed and employed in this study. Because of the strong field strength in the small air gap formed by the electrode and the water surface, glow discharge plasmas were generated and used to treat waste water. The electric field distribution of the designed electrode model was simulated by MAXWELL 3D® simulation software, and the discharge parameters were measured. Through a series of experiments, we investigated the impact of optimal designs, such as the dielectric of the electrode, immersion depths, and curvature radii of the electrode on the generation characteristics of plasmas. In addition, we designed an equipotential multi-electrode configuration to treat a Methyl Violet solution and observe the discoloration effect. The experimental and simulation results indicate that the designed electrodes can realize glow discharge with a relative low voltage, and the generated plasmas covered a large area and were in stable state. The efficiency of water treatment is improved and optimized with the designed electrodes.

  20. Formation and characteristics of patterns in atmospheric-pressure radio-frequency dielectric barrier discharge plasma

    Science.gov (United States)

    Yang, Lizhen; Liu, Zhongwei; Mao, Zhiguo; Li, Sen; Chen, Qiang

    2017-01-01

    The patterns in radio-frequency dielectric barrier discharge (RF DBD) are studied at atmospheric pressure of argon (Ar) or helium (He) mixed with nitrogen (N2) gas. When a small amount of N2 is mixed with He or Ar gas, discharge patterns are formed. In a N2/He gas mixture, besides the filament discharge that forms patterns, a glow background discharge is also observed, whereas only the filament discharge forms patterns in a N2/Ar gas mixture. The resolution of the hexagonal pattern as a function of applied power and gas flow rate is then explored. On the basis of spatial-temporal images taken using an intensified charge-coupled device (ICCD), we find that there is no interleaving of two transient hexagon sublattices in N2/Ar or N2/He plasma in RF DBD patterns, which are totally different from those in which surface charges dominated in the mid-frequency DBD plasma. This supports our hypothesis that the bulk charges dominate the pattern formation in RF DBD.

  1. Methane Conversion to C2 Hydrocarbons Using Glow Discharge Plasma

    Institute of Scientific and Technical Information of China (English)

    HU Miao; CHEN Jierong

    2007-01-01

    The infrared emission spectra of methane, H', CH and C2 hydrocarbons in natural gas were measured. The process of methane decomposition and C2 hydrocarbons formation was investigated. The experiment showed that the time and conditions of methane decomposition and C2 hydrocarbons formation were different. Methane conversion rate increased with the increase in the current and decrease in the amount of methane. Furthermore, an examination of the reaction mechanisms revealed that free radicals played an important role in the chain reaction.

  2. Influence of the energy dissipation rate in the discharge of a plasma synthetic jet actuator

    Energy Technology Data Exchange (ETDEWEB)

    Belinger, A; Cambronne, J P [Universite de Toulouse, UPS, INPT, LAPLACE - Laboratoire Plasma et Conversion d' Energie, 118 route de Narbonne, F-31062 Toulouse cedex 9 (France); Hardy, P; Barricau, P; Caruana, D, E-mail: daniel.caruana@onera.fr [ONERA Centre Midi-Pyrenees, Departement Modeles pour l' Aerodynamique et l' Energetique, BP74025, 2 avenue Edouard Belin, 31055 TOULOUSE CEDEX 4 (France)

    2011-09-14

    A promising actuator for high-speed flow control, referred to as a plasma synthetic jet (PSJ), is being studied by the DMAE department of the ONERA, and the Laplace laboratory of the CNRS, in France. This actuator was inspired by the 'sparkjet' device developed by the Johns Hopkins University Applied Physics Laboratory. The PSJ, which produces a synthetic jet with high exhaust velocities, no active mechanical components and no mass flow admission, holds the promise of enabling high-speed flows to be manipulated. With this high-velocity jet it is possible to reduce fluid phenomena such as transition and turbulence, thus making it possible to increase an aircraft's performance whilst at the same time reducing its environmental impact. A thermal plasma discharge was created in a micro-cavity, causing the gas to be expelled. It is relevant that the velocity and momentum depend on the energy dispersed by the electric discharge. To control the frequency and energy dispersed in the plasma, the Laplace laboratory has developed two high-voltage power supply systems. These allow two different types of discharge to be produced, with energy being supplied to the discharge in two different manners. In this paper, we focus on the impact of the power supply on the plasma synthetic jet, and in particular on the role of the rate of energy dissipation in the discharge. In order to estimate the influence of the power supply on the machinery of the actuator, specific experimental techniques were used to investigate the electrical (voltage, current), thermal (Infra-red camera) and aerodynamic (jet duration, isentropic pressure, jet velocity) characteristics. These data sets were used to determine which of the two power supplies was more effective, thus allowing us to reach several conclusions concerning the importance of the energy dissipation rate on the PSJ actuator.

  3. Packed-bed reactor/silent-discharge plasma design data report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    In 1992, Congress passed the Federal Facility Compliance Act requiring the U.S. Department of Energy (DOE) to treat and dispose of its mixed waste in accordance with Resource Conservation and Recovery Act (RCRA) land disposal restrictions (LDRs). The DOE Albuquerque Operations Office (AL) currently does not have adequate systems to treat the mixed wastes generated and stored at the nine DOE-AL sites. In response to the need for mixed-waste treatment capacity, DOE-AL organized a Treatment Selection Team under the Mixed-Waste Treatment Program (MWTP) to match mixed wastes with treatment options and develop a strategy for treatment of its mixed waste. The strategy developed by the Treatment Selection Team, as described in the AL Mixed-Waste Treatment Plan (DOE 1994), is to use available off-site commercial treatment facilities for all wastes that can be successfully and cost-effectively treated by such facilities. Where no appropriate commercial treatment facilities exist, mobile treatment units (MTUs) would be developed to treat wastes at the sites where the wastes are generated. Treatment processes used for mixed waste must not only address the hazardous component (i.e., meet LDRs) but also must contain the radioactive component in a form that allows final disposal while protecting workers, the public, and the environment. The packed-bed reactor/silent discharge plasma was chosen as a potential candidate for the treatment of the mixed wastes. The process is described.

  4. The Effect of Dielectric Barrier Discharge Plasma Treatment on the Microorganisms Found in Raw Cow’s Milk

    OpenAIRE

    Aslan, Yakup

    2016-01-01

    Milk is an essential source of nutrition especially for the breastfed infants. Sterilization of milk is necessary because it can be contaminated by microorganisms due to unhygienic collection and storage conditions. In this study, the sterilization of raw cow milk was performed by using dielectric barrier discharge (DBD) plasma method. Raw milk was transferred to the plasma reactor and dielectric barrier discharge cold plasma was performed by changing various parameters including voltage, exp...

  5. Note: Rapid reduction of graphene oxide paper by glow discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Bo, Zheng; Qian, Jiajing; Duan, Liangping; Qiu, Kunzan, E-mail: qiukz@zju.edu.cn; Yan, Jianhua; Cen, Kefa [State Key Laboratory of Clean Energy Utilization, College of Energy Engineering, Zhejiang University, Hangzhou, Zhejiang 310027 (China); Han, Zhao Jun [CSIRO Manufacturing Flagship, P.O. Box 218, Bradfield Road, Lindfield, New South Wales 2070 (Australia); Ostrikov, Kostya [CSIRO Manufacturing Flagship, P.O. Box 218, Bradfield Road, Lindfield, New South Wales 2070 (Australia); Institute for Future Environments and School of Chemistry, Physics and Mechanical Engineering, Queensland University of Technology, Brisbane, Queensland 4000 (Australia)

    2015-05-15

    This note reports on a novel method for the rapid reduction of graphene oxide (GO) paper using a glow discharge plasma reactor. Glow discharge is produced and sustained between two parallel-plate graphite electrodes at a pressure of 240 mTorr. By exposing GO paper at the junction of negative-glow and Faraday-dark area for 4 min, the oxygen-containing groups can be effectively removed (C/O ratio increases from 2.6 to 7.9), while the material integrality and flexibility are kept well. Electrochemical measurements demonstrate that the as-obtained reduced GO paper can be potentially used for supercapacitor application.

  6. Optical Emission Spectroscopy Investigation of a Surface Dielectric Barrier Discharge Plasma Aerodynamic Actuator

    Institute of Scientific and Technical Information of China (English)

    LI Ying-Hong; WU Yun; JIA Min; ZHOU Zhang-Wen; GUO Zhi-Gang; PU Yi-Kang

    2008-01-01

    The optical emission spectroscopy of a surface dielectric barrier discharge plasma aerodynamic actuator is investigated with different electrode configurations, applied voltages and driving frequencies. The rotational temperature of N2 (C3IIu) molecule is calculated according to its rotational emission band near 380.5 nm. The average electron energy of the discharge is evaluated by emission intensity ratio of first negative system to second positive system of N2. The rotational temperature is sensitive to the inner space of an electrode pair. The average electron energy shows insensitivity to the applied voltage, the driving frequency and the electrode configuration.

  7. Treatment of Candida albicans biofilms with low-temperature plasma induced by dielectric barrier discharge and atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Koban, Ina; Welk, Alexander; Meisel, Peter; Holtfreter, Birte; Kocher, Thomas [Unit of Periodontology, Dental School, University of Greifswald, Rotgerberstr. 8, 17475 Greifswald (Germany); Matthes, Rutger; Huebner, Nils-Olaf; Kramer, Axel [Institute for Hygiene and Environmental Medicine, University of Greifswald, Walther-Rathenau-Str. 49 a, 17487 Greifswald (Germany); Sietmann, Rabea [Institute of Microbiology, University of Greifswald, Friedrich-Ludwig-Jahn-Str. 15, 17487 Greifswald (Germany); Kindel, Eckhard; Weltmann, Klaus-Dieter, E-mail: ina.koban@uni-greifswald.d [Leibniz Institute for Plasma Science and Technology (INP), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

    2010-07-15

    Because of some disadvantages of chemical disinfection in dental practice (especially denture cleaning), we investigated the effects of physical methods on Candida albicans biofilms. For this purpose, the antifungal efficacy of three different low-temperature plasma devices (an atmospheric pressure plasma jet and two different dielectric barrier discharges (DBDs)) on Candida albicans biofilms grown on titanium discs in vitro was investigated. As positive treatment controls, we used 0.1% chlorhexidine digluconate (CHX) and 0.6% sodium hypochlorite (NaOCl). The corresponding gas streams without plasma ignition served as negative treatment controls. The efficacy of the plasma treatment was determined evaluating the number of colony-forming units (CFU) recovered from titanium discs. The plasma treatment reduced the CFU significantly compared to chemical disinfectants. While 10 min CHX or NaOCl exposure led to a CFU log{sub 10} reduction factor of 1.5, the log{sub 10} reduction factor of DBD plasma was up to 5. In conclusion, the use of low-temperature plasma is a promising physical alternative to chemical antiseptics for dental practice.

  8. Fast plasma discharge capillary design as a high power throughput soft x-ray emission source.

    Science.gov (United States)

    Wyndham, E S; Favre, M; Valdivia, M P; Valenzuela, J C; Chuaqui, H; Bhuyan, H

    2010-09-01

    We present the experimental details and results from a low energy but high repetition rate compact plasma capillary source for extreme ultraviolet and soft x-ray research and applications. Two lengths of capillary are mounted in two versions of a closely related design. The discharge operates in 1.6 and 3.2 mm inner diameter alumina capillaries of lengths 21 and 36 mm. The use of water both as dielectric and as coolant simplifies the compact low inductance design with nanosecond discharge periods. The stored electrical energy of the discharge is approximately 0.5 J and is provided by directly charging the capacitor plates from an inexpensive insulated-gate bipolar transistor in 1 μs or less. We present characteristic argon spectra from plasma between 30 and 300 Å as well as temporally resolved x-ray energy fluence in discrete bands on axis. The spectra also allow the level of ablated wall material to be gauged and associated with useful capillary lifetime according to the chosen configuration and energy storage. The connection between the electron beams associated with the transient hollow cathode mechanism, soft x-ray output, capillary geometry, and capillary lifetime is reported. The role of these e-beams and the plasma as measured on-axis is discussed. The relation of the electron temperature and the ionization stages observed is discussed in the context of some model results of ionization in a non-Maxwellian plasma.

  9. Production characteristics of reactive oxygen/nitrogen species in water using atmospheric pressure discharge plasmas

    Science.gov (United States)

    Takahashi, Kazuhiro; Satoh, Kohki; Itoh, Hidenori; Kawaguchi, Hideki; Timoshkin, Igor; Given, Martin; MacGregor, Scott

    2016-07-01

    A pulsed discharge, a DC corona discharge, and a plasma jet are separately generated above a water surface, and reactive oxygen species and reactive nitrogen species (ROS/RNS) in the water are investigated. ROS/RNS in water after the sparging of the off-gas of a packed-bed dielectric barrier discharge (PB-DBD) are also investigated. H2O2, NO2 -, and NO3 - are detected after plasma exposure and only NO3 - after off-gas sparging. Short-lifetime species in plasma are found to play an important role in H2O2 and NO2 - production and long-lifetime species in NO3 - production. NO x may inhibit H2O2 production through OH consumption to produce HNO2 and HNO3. O3 does not contribute to ROS/RNS production. The pulsed plasma exposure is found to be effective for the production of H2O2 and NO2 -, and the off-gas sparging of the PB-DBD for the production of NO3 -.

  10. Application of Non-Thermal Plasma to the Treatment of Effluent Discharged Into River Choumlou in Bafoussam, West Cameroon

    Directory of Open Access Journals (Sweden)

    Estella T. Njoyim

    2016-07-01

    Full Text Available Most rivers in urban areas of developing countries are the of effluents discharged from industries. This is the case of River Choumlou (in Bafoussam-West Region, Cameroon which receives all discharges from “Brasseries du Cameroun”, Bafoussam branch. The objective of this work was to determine the level of organic contaminants in water samples and to treat the polluted samples using the non-thermal gliding arc plasma. Nonthermal plasma consists of charged particles, radicals and excited molecules. The aim was to show the interest of such a process for cleaning up of surface waters (real effluent and to cope with the protection of our environment. Due to the fact that pollution of streams and rivers from the discharge of sewage and industrial wastes poses a major problem to the environment, the researchers were particularly interested in investigating the oxidizing and acidifying properties of non-thermal plasma on polluted surface water. Samples were collected upstream and downstream from the brewery’s effluent outlet. Samples taken at the point R1 (downstream were first analyzed by volumetric and instrumental methods in order to determine the organoleptic, physico-chemical and organic parameters. These samples were then exposed to the gliding discharge in humid air for a time period of between 3-30 minutes. After 30 minutes of exposure, a decrease in turbidity (24.09%, BOD5 (44.93% and COD (48.92% were observed resulting in transparency apparition; with a decrease in pH (7.9 to 3 due to the formation of acidifying species in solution. These results reflect a considerable reduction in the pollution load of the water collected at R1. This work shows that the effectiveness of the Gliding Arc in wastewater treatment is attributed to the oxidizing power of the hydroxyl radical and acidifying power of the nitrogen monoxide radical formed in the plasma. Despite the low rate of reduction of COD and BOD5 in 30 min, it can be said that the plasma

  11. FAST TRACK COMMUNICATION: On the application of inductively coupled plasma discharges sustained in Ar/O2/N2 ternary mixture for sterilization and decontamination of medical instruments

    Science.gov (United States)

    Stapelmann, K.; Kylián, O.; Denis, B.; Rossi, F.

    2008-10-01

    Non-equilibrium low pressure-plasma discharges are extensively studied for their high potential in the field of sterilization and decontamination of medical devices. This increased interest in plasma discharges arises from, among other reasons, their capability not only to inactivate bacterial spores but also to eliminate, destroy or remove pathogenic biomolecules and thus to provide a one-step process assuring safety of treated instruments. However, recent studies have shown that optimal conditions leading to inactivation of spores and physical removal of pathogens differ significantly—the efficiency of spores sterilization is above all dependent on the UV radiation intensity, whereas high etching rates are connected with the presence of the etching agent, typically atomic oxygen. The aim of this contribution is to discuss and demonstrate the feasibility of Ar/N2/O2 low-pressure inductively coupled plasma discharges as an option to provide intense UV radiation while maintaining the high etching rates of biomolecules.

  12. Lean methodology for performance improvement in the trauma discharge process.

    Science.gov (United States)

    O'Mara, Michael Shaymus; Ramaniuk, Aliaksandr; Graymire, Vickie; Rozzell, Monica; Martin, Stacey

    2014-07-01

    High-volume, complex services such as trauma and acute care surgery are at risk for inefficiency. Lean process improvement can reduce health care waste. Lean allows a structured look at processes not easily amenable to analysis. We applied lean methodology to the current state of communication and discharge planning on an urban trauma service, citing areas for improvement. A lean process mapping event was held. The process map was used to identify areas for immediate analysis and intervention-defining metrics for the stakeholders. After intervention, new performance was assessed by direct data evaluation. The process was completed with an analysis of effect and plans made for addressing future focus areas. The primary area of concern identified was interservice communication. Changes centering on a standardized morning report structure reduced the number of consult questions unanswered from 67% to 34% (p = 0.0021). Physical therapy rework was reduced from 35% to 19% (p = 0.016). Patients admitted to units not designated to the trauma service had 1.6 times longer stays (p lean process lasted 8 months, and three areas for new improvement were identified: (1) the off-unit patients; (2) patients with length of stay more than 15 days contribute disproportionately to length of stay; and (3) miscommunication exists around patient education at discharge. Lean process improvement is a viable means of health care analysis. When applied to a trauma service with 4,000 admissions annually, lean identifies areas ripe for improvement. Our inefficiencies surrounded communication and patient localization. Strategies arising from the input of all stakeholders led to real solutions for communication through a face-to-face morning report and identified areas for ongoing improvement. This focuses resource use and identifies areas for improvement of throughput in care delivery.

  13. Synthesis of magnetic nanoparticles by atmospheric-pressure glow discharge plasma-assisted electrolysis

    Science.gov (United States)

    Shirai, Naoki; Yoshida, Taketo; Uchida, Satoshi; Tochikubo, Fumiyoshi

    2017-07-01

    For the synthesis of magnetic nanoparticles (NPs), we used plasma-assisted electrolysis in which atmospheric-pressure DC glow discharge using a liquid electrode is combined with electrolysis. The solution surface is exposed to positive ions or electrons in plasma. To synthesize magnetic NPs, aqueous solutions of FeCl2 or an iron electrode immersed in liquid was used to supply iron ions in the liquid. Magnetic NPs were synthesized at the plasma-liquid interface upon the electron irradiation of the liquid surface. In the case of using aqueous solutions of FeCl2, the condition of magnetic NP synthesis depended on the gas species of plasma and the chemical agent in the liquid for controlling oxidization. The amount of magnetic NPs synthesized using plasma is not very large. On the other hand, in the case of using an iron electrode immersed in NaCl solution, magnetic NPs were synthesized without using FeCl2 solutions. When plasma-assisted electrolysis was operated, the iron electrode eluted Fe cations, resulting in the formation of magnetic NPs at the plasma-liquid interface. Magnetic NP synthesis depended on the concentration of NaCl solution and discharge current. The magnetic NPs were identified to be magnetite. By using this method, more magnetite NPs were synthesized than in the case of plasma-assisted electrolysis with FeCl2 aqueous solutions. The pH of the liquid used in plasma-assisted electrolysis was important for the synthesis of magnetite NPs.

  14. Laser Optogalvanic Spectroscopy pf Neon and Argon in a Discharge Plasma and its Significance for Microgravity Combustion

    Science.gov (United States)

    Misra, Prabhakar; Haridass, C.; Major, H.

    1999-01-01

    A detailed study of combustion mechanisms in flames, employing laser-based diagnostics, has provided good knowledge and understanding of the physical phenomena, and led to better characterization of the dynamical and chemical combustion processes, both under low-gravity (in space) and normal gravity (in ground based facilities, e.g. drop towers). Laser induced fluorescence (LIF), laser-induced incandescence (LII) and LIF thermometry have been widely used to perform nonintrusive measurements and to better understand combustion phenomena. Laser optogalvanic (LOG) spectroscopy has well-established applications in ion mobility measurements, atomic and molecular spectroscopy, ionization rates, recombination rates, velocity measurements and as a combustion probe for trace element detection. Absorption spectra of atomic and molecular species in flames can be obtained via LOG spectroscopy by measuring the voltage and current changes induced by laser irradiation. There are different kinds of processes that contribute to a discharge current, namely: (1) electron impact ionization, (2) collisions among the excited atoms of the discharge species and (3) Penning ionization. In general, at higher discharge currents, the mechanism of electron impact ionization dominates over Penning ionization, whereby the latter is hardly noticeable. In a plasma, whenever the wavelength of a laser coincides with the absorption of an atomic or molecular species, the rate of ionization of the species momentarily increases or decreases due to laser-assisted acceleration of collisional ionization. Such a rate of change in the ionization is monitored as a variation in the transient current by inserting a high voltage electrode into the plasma. Optogalvanic spectroscopy in discharges has been useful for characterizing laser line-widths and for providing convenient calibration lines for tunable dye lasers in the ultraviolet, visible and infrared wavelength regions. Different kinds of quantitative

  15. A tomographic visualization of electric discharge sound fields in atmospheric pressure plasma using laser diffraction

    Science.gov (United States)

    Nakamiya, Toshiyuki; Mitsugi, Fumiaki; Iwasaki, Yoichiro; Ikegami, Tomoaki; Tsuda, Ryoichi; Sonoda, Yoshito; Danuta Stryczewska, Henryka

    2013-02-01

    The phase modulation of transparent gas can be detected using Fraunhofer diffraction technique, which we call optical wave microphone (OWM). The OWM is suitable for the detection of sonic wave from audible sound to ultrasonic wave. Because this technique has no influence on sound field or electric field during the measurement, we have applied it to the sound detection for the electric discharges. There is almost no research paper that uses the discharge sound to examine the electrical discharge phenomenon. Two-dimensional visualization of the sound field using the OWM is also possible when the computerized tomography (CT) is combined. In this work, coplanar dielectric barrier discharge sin different gases of Ar, N2, He were characterized via the OWM as well as applied voltage and discharge current. This is the first report to investigate the influence of the type of the atmospheric gas on the two-dimensional sound field distribution for the coplanar dielectric barrier discharge using the OWM with CT. Contribution to the Topical Issue "13th International Symposium on High Pressure Low Temperature Plasma Chemistry (Hakone XIII)", Edited by Nicolas Gherardi, Henryca Danuta Stryczewska and Yvan Ségui.

  16. Atomic processes in optically thin plasmas

    Science.gov (United States)

    Kaastra, Jelle S.; Gu, Liyi; Mao, Junjie; Mehdipour, Missagh; Raassen, Ton; Urdampilleta, Igone

    2016-10-01

    The Universe contains a broad range of plasmas with quite different properties depending on distinct physical processes. In this contribution we give an overview of recent developments in modeling such plasmas with a focus on X-ray emission and absorption. Despite the fact that such plasmas have been investigated already for decades, and that overall there is a good understanding of the basic processes, there are still areas, where improvements have to be made that are important for the analysis of astrophysical plasmas. We present recent work on the update of atomic parameters in the codes that describe the emission from collisional plasmas, where older approximations are being replaced now by more accurate data. Further we discuss the development of models for photo-ionised plasmas in the context of outflows around supermassive black holes and models for charge transfer that are needed for analyzing the data from the upcoming ASTRO-H satellite.

  17. On the physical processes ruling an atmospheric pressure air glow discharge operating in an intermediate current regime

    Energy Technology Data Exchange (ETDEWEB)

    Prevosto, L., E-mail: prevosto@waycom.com.ar; Mancinelli, B.; Chamorro, J. C.; Cejas, E. [Grupo de Descargas Eléctricas, Departamento Ing. Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina); Kelly, H. [Grupo de Descargas Eléctricas, Departamento Ing. Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina); Instituto de Física del Plasma (CONICET), Facultad de Ciencias Exactas y Naturales (UBA) Ciudad Universitaria Pab. I, 1428, Buenos Aires (Argentina)

    2015-02-15

    Low-frequency (100 Hz), intermediate-current (50 to 200 mA) glow discharges were experimentally investigated in atmospheric pressure air between blunt copper electrodes. Voltage–current characteristics and images of the discharge for different inter-electrode distances are reported. A cathode-fall voltage close to 360 V and a current density at the cathode surface of about 11 A/cm{sup 2}, both independent of the discharge current, were found. The visible emissive structure of the discharge resembles to that of a typical low-pressure glow, thus suggesting a glow-like electric field distribution in the discharge. A kinetic model for the discharge ionization processes is also presented with the aim of identifying the main physical processes ruling the discharge behavior. The numerical results indicate the presence of a non-equilibrium plasma with rather high gas temperature (above 4000 K) leading to the production of components such as NO, O, and N which are usually absent in low-current glows. Hence, the ionization by electron-impact is replaced by associative ionization, which is independent of the reduced electric field. This leads to a negative current-voltage characteristic curve, in spite of the glow-like features of the discharge. On the other hand, several estimations show that the discharge seems to be stabilized by heat conduction; being thermally stable due to its reduced size. All the quoted results indicate that although this discharge regime might be considered to be close to an arc, it is still a glow discharge as demonstrated by its overall properties, supported also by the presence of thermal non-equilibrium.

  18. Miniature Dielectric Barrier Discharge Nonthermal Plasma Induces Apoptosis in Lung Cancer Cells and Inhibits Cell Migration

    Science.gov (United States)

    Eisenmann, Kathryn M.

    2017-01-01

    Traditional cancer treatments like radiotherapy and chemotherapy have drawbacks and are not selective for killing only cancer cells. Nonthermal atmospheric pressure plasmas with dielectric barrier discharge (DBD) can be applied to living cells and tissues and have emerged as novel tools for localized cancer therapy. The purpose of this study was to investigate the different effects caused by miniature DBD (mDBD) plasma to A549 lung cancer cells. In this study, A549 lung cancer cells cultured in 12 well plates were treated with mDBD plasma for specified treatment times to assess the changes in the size of the area of cell detachment, the viability of attached or detached cells, and cell migration. Furthermore, we investigated an innovative mDBD plasma-based therapy for localized treatment of lung cancer cells through apoptotic induction. Our results indicate that plasma treatment for 120 sec causes apoptotic cell death in 35.8% of cells, while mDBD plasma treatment for 60 sec, 30 sec, or 15 sec causes apoptotic cell death in 20.5%, 14.1%, and 6.3% of the cell population, respectively. Additionally, we observed reduced A549 cell migration in response to mDBD plasma treatment. Thus, mDBD plasma system can be a viable platform for localized lung cancer therapy. PMID:28243603

  19. Cold atmospheric plasma discharged in water and its potential use in cancer therapy

    Science.gov (United States)

    Chen, Zhitong; Cheng, Xiaoqian; Lin, Li; Keidar, Michael

    2017-01-01

    Cold atmospheric plasma (CAP) has emerged as a novel technology for cancer treatment. CAP can directly treat cells and tissue but such direct application is limited to skin or can be invoked as a supplement during open surgery. In this study we report indirect plasma treatment using CAP discharged in deionized (DI) water using three gases as carriers (argon (Ar), helium (He), and nitrogen (N2)). Plasma stimulated water was applied to the human breast cancer cell line (MDA-MB-231). MTT (3-(4, 5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay tests showed that using Ar plasma had the strongest effect on inducing apoptosis in cultured human breast cancer cells. This result is attributed to the elevated production of reactive oxygen species and reactive nitrogen species in water.

  20. Three dimensional complex plasma structures in a combined radio frequency and direct current discharge

    CERN Document Server

    Mitic, S; Khrapak, S A; Morfill, G E; 10.1063/1.4798418

    2013-01-01

    We report on the first detailed analysis of large three dimensional (3D) complex plasma structures in experiments performed in pure rf and combined rf+dc discharge modes. Inductively coupled plasma (ICP) is generated by an rf coil wrapped around the vertically positioned cylindrical glass tube at a pressure of 0.3 mbar. In addition, dc plasma can be generated by applying voltage to the electrodes at the ends of the tube far from the rf coil. The injected monodisperse particles are levitated in the plasma below the coil. A scanning laser sheet and a high resolution camera are used to determine the 3D positions of about $10^5$ particles. The observed bowl-shaped particle clouds reveal coexistence of various structures, including well-distinguished solid-like, less ordered liquid-like, and pronounced string-like phases. New criteria to identify string-like structures are proposed.

  1. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage

    Science.gov (United States)

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-01-01

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction. PMID:27759080

  2. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage

    Science.gov (United States)

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-10-01

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction.

  3. Boltzmann statistical consideration on the excitation mechanism of iron atomic lines emitted from glow discharge plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Lei; Kashiwakura, Shunsuke; Wagatsuma, Kazuaki, E-mail: wagatuma@imr.tohoku.ac.jp

    2011-11-15

    A Boltzmann plot for many iron atomic lines having excitation energies of 3.3-6.9 eV was investigated in glow discharge plasmas when argon or neon was employed as the plasma gas. The plot did not show a linear relationship over a wide range of the excitation energy, but showed that the emission lines having higher excitation energies largely deviated from a normal Boltzmann distribution whereas those having low excitation energies (3.3-4.3 eV) well followed it. This result would be derived from an overpopulation among the corresponding energy levels. A probable reason for this is that excitations for the high-lying excited levels would be caused predominantly through a Penning-type collision with the metastable atom of argon or neon, followed by recombination with an electron and then stepwise de-excitations which can populate the excited energy levels just below the ionization limit of iron atom. The non-thermal excitation occurred more actively in the argon plasma rather than the neon plasma, because of a difference in the number density between the argon and the neon metastables. The Boltzmann plots yields important information on the reason why lots of Fe I lines assigned to high-lying excited levels can be emitted from glow discharge plasmas. - Highlights: Black-Right-Pointing-Pointer This paper shows the excitation mechanism of Fe I lines from a glow discharge plasma. Black-Right-Pointing-Pointer A Boltzmann distribution is studied among iron lines of various excitation levels. Black-Right-Pointing-Pointer We find an overpopulation of the high-lying energy levels from the normal distribution. Black-Right-Pointing-Pointer It is caused through Penning-type collision of iron atom with argon metastable atom.

  4. A plasma process monitor/control system

    Energy Technology Data Exchange (ETDEWEB)

    Stevenson, J.O.; Ward, P.P.; Smith, M.L. [Sandia National Labs., Albuquerque, NM (United States); Markle, R.J. [Advanced Micro Devices, Inc., Austin, TX (United States)

    1997-08-01

    Sandia National Laboratories has developed a system to monitor plasma processes for control of industrial applications. The system is designed to act as a fully automated, sand-alone process monitor during printed wiring board and semiconductor production runs. The monitor routinely performs data collection, analysis, process identification, and error detection/correction without the need for human intervention. The monitor can also be used in research mode to allow process engineers to gather additional information about plasma processes. The plasma monitor can perform real-time control of support systems known to influence plasma behavior. The monitor can also signal personnel to modify plasma parameters when the system is operating outside of desired specifications and requires human assistance. A notification protocol can be selected for conditions detected in the plasma process. The Plasma Process Monitor/Control System consists of a computer running software developed by Sandia National Laboratories, a commercially available spectrophotometer equipped with a charge-coupled device camera, an input/output device, and a fiber optic cable.

  5. One-equation modeling and validation of dielectric barrier discharge plasma actuator thrust

    Science.gov (United States)

    Yoon, Jae-San; Han, Jae-Hung

    2014-10-01

    Dielectric barrier discharge (DBD) plasma actuators with an asymmetric electrode configuration can generate a wall-bounded jet without mechanical moving parts, which require considerable modifications of existing aeronautical objects and which incur high maintenance costs. Despite this potential, one factor preventing the wider application of such actuators is the lack of a reliable actuator model. It is difficult to develop such a model because calculating the ion-electric field and fluid interaction consume a high amount calculation effort during the numerical analysis. Thus, the authors proposed a semi-empirical model which predicted the thrust of plasma actuators with a simple equation. It gave a numeric thrust value, and we implemented the value on a computational fluid dynamics (CFD) solver to describe the two-dimensional flow field induced by the actuator. However, the model had a narrow validation range, depending on the empirical formula, and it did not fully consider environment variables. This study presents an improved model by replacing the empirical formulae in the previous model with physical equations that take into account physical phenomena and environmental variables. During this process, additional operation parameters, such as pressure, temperature and ac waveforms, are newly taken to predict the thrust performance of the actuators with a wider range of existing parameters, the thickness of the dielectric barrier, the exposed electrode, the dielectric constant, the ac frequency and the voltage amplitude. Thrust prediction curves from the model are compared to those of earlier experimental results, showing that the average error is less than 5% for more than one hundred instances of data. As in the earlier work, the predicted thrust value is implemented on a CFD solver, and two-dimensional wall-jet velocity profiles induced by the actuator are compared to the previous experimental results.

  6. Analysis of Ar plasma jets induced by single and double dielectric barrier discharges at atmospheric pressure

    Science.gov (United States)

    Judée, F.; Merbahi, N.; Wattieaux, G.; Yousfi, M.

    2016-09-01

    The aim is the comparison of different plasma parameters of single and double dielectric barrier discharge plasma jet configurations (S-DBD and D-DBD) which are potentially usable in biomedical applications. Both configurations are studied in terms of electric field distribution, electrical discharge characteristics, plasma parameters (estimated by optical emission spectroscopy analysis), and hydrodynamics of the plasma jet for electrical parameters of power supplies corresponding to an applied voltage of 10 kV, pulse duration of 1 μs, frequency of 9.69 kHz, and Ar flow of 2 l/min. We observed that the D-DBD configuration requires half the electrical power one needs to provide in the S-DBD case to generate a plasma jet with similar characteristics: excitation temperature around 4700 K, electron density around 2.5 × 1014 cm-3, gas temperature of about 320 K, a relatively high atomic oxygen concentration reaching up to 1000 ppm, the presence of reactive oxygen and nitrogen species (nitric oxide, hydroxyl radical, and atomic oxygen), and an irradiance in the UV-C range of about 20 μW cm-2. Moreover, it has been observed that D-DBD plasma jet is more sensitive to short pulse durations, probably due to the charge accumulation over the dielectric barrier around the internal electrode. This results in a significantly longer plasma length in the D-DBD configuration than in the S-DBD one up to a critical flow rate (2.25 l/min) before the occurrence of turbulence in the D-DBD case. Conversely, ionization wave velocities are significantly higher in the S-DBD setup (3.35 × 105 m/s against 1.02 × 105 m/s for D-DBD), probably due to the higher electrostatic field close to the high voltage electrode in the S-DBD plasma jet.

  7. Numerical study on the characteristics of nitrogen discharge at high pressure with induced plasma

    Institute of Scientific and Technical Information of China (English)

    Wang Yi-Nan; Liu Yue; Zheng Shu; Lin Guo-Qiang

    2012-01-01

    Based on the fluid theory of plasma,a model is built to study the characteristics of nitrogen discharge at high pressure with induced argon plasma.In the model,species such as electrons,N2+,N4+,Ar+,and two metastable states (N2(A3 ∑ u+),N2(a1 ∑ u-)) are taken into account.The model includes the particle continuity equation,the electron energy balance equation,and Poisson(柤)equation.The model is solved with a finite difference method.The numerical results are obtained and used to investigate the effect of time taken to add nitrogen gas and initially-induced argon plasma pressure.It is found that lower speeds of adding the nitrogen gas and varying the gas pressure can induce higher plasma density,and inversely lower electron temperature.At high-pressure discharge,the electron density increases when the proportion of nitrogen component is below 40%,while the electron density will keep constant as the nitrogen component further increases.It is also shown that with the increase of initially-induced argon plasma pressure,the density of charged particles increases,and the electron temperature as well as the electric field decreases.

  8. Single-Crystal MgO Hollow Nanospheres Formed in RF Impulse Discharge Plasmas

    Directory of Open Access Journals (Sweden)

    Satoru Iizuka

    2012-01-01

    Full Text Available Spherical MgO nanoparticles with a hollow inside, that is, MgO hollow nanospheres, were created in Ar/O2 plasma produced by radio frequency (RF impulse discharge using a Mg rod electrode. The hollow nanospheres were found on the SiO2 plates placed near the powered Mg electrode. The electron refraction pattern showed that each nanosphere was made of a single crystal of MgO. Since the shape was spherical, these nanoparticles seemed to be created during the levitation in the plasma without touching any walls. The formation mechanism with a quasiliquid cooling model was also discussed.

  9. Study of fast capillary discharge plasma columns for soft x-ray amplifiers

    Science.gov (United States)

    Rocca, Jorge J. G.; Cortazar, O. D.; Szapiro, Benito T.; Tomasel, Fernando G.; Hartshorn, D.

    1994-02-01

    The efficient generation, by a fast discharge, of capillary plasma channels containing Ne-like and Ni-like ions for collisionally excited soft-x-ray lasers is reported. Rapid pulse excitation of capillary channels 1.5 mm in diameter with currents of less than 70 kA produced Ca and Ti plasmas in which atoms are ionized up to the F-like state. Line emission at the wavelengths corresponding to the 3p - 3s and 3d - 3p transitions of Ne-like Ca has been observed.

  10. Plasma Treatment of Polyethylene Powder Particles in Hollow Cathode Glow Discharge

    Science.gov (United States)

    Wolter, Matthias; Quitzau, Meike; Bornholdt, Sven; Kersten, Holger

    2008-09-01

    Polyethylen (PE) is widely used in the production of foils, insulators, packaging materials, plastic bottles etc. Untreated PE is hydrophobic due to its unpolar surface. Therefore, it is hard to print or glue PE and the surface has to be modified before converting. In the present experiments a hollow cathode glow discharge is used as plasma source which is mounted in a spiral conveyor in order to ensure a combines transport of PE powder particles. With this set-up a homogeneous surface treatment of the powder is possible while passing the glow discharge. The plasma treatment causes a remarkable enhancement of the hydrophilicity of the PE powder which can be verified by contact angle measurements and X-ray photoelectron spectroscopy.

  11. Canard-induced mixed mode oscillations in an excitable glow discharge plasmas

    CERN Document Server

    Nurujjaman, M

    2014-01-01

    We demonstrated experimentally canard induced mixed mode oscillations (MMO) in an excitable glow discharge plasma, and the results are validated through numerical solution of the FitzHugh Nagumo (FHN) model. When glow discharge plasma is perturbed by applying a magnetic field, it shows mixed mode oscillatory activity, i.e., quasiperiodic small oscillations interposed with large bounded limit cycles oscillations. The initial quasiperiodic oscillations were observed to change into large amplitude limit cycle oscillations with magnetic field, and the number of these oscillation increases with increase in the magnetic field. Fourier analysis of both numerical and experimental results show that the origin of these oscillations are canard-induced phenomena, which occurs near the threshold of the control parameter. Further, the phase space plots also confirm that the oscillations are basically canard-induced MMOs.

  12. Reel-to-Reel Atmospheric Pressure Dielectric Barrier Discharge (DBD Plasma Treatment of Polypropylene Films

    Directory of Open Access Journals (Sweden)

    Lukas JW Seidelmann

    2017-03-01

    Full Text Available Atmospheric pressure plasma treatment of the surface of a polypropylene film can significantly increase its surface energy and, thereby improve the printability of the film. A laboratory-scale dielectric barrier discharge (DBD system has therefore been developed, which simulates the electrode configuration and reel-to-reel web transport mechanism used in a typical industrial-scale system. By treating the polypropylene in a nitrogen discharge, we have shown that the water contact angle could be reduced by as much as 40° compared to the untreated film, corresponding to an increase in surface energy of 14 mNm−1. Ink pull-off tests showed that the DBD plasma treatment resulted in excellent adhesion of solvent-based inks to the polypropylene film.

  13. A compact, low cost Marx bank for generating capillary discharge plasmas

    Science.gov (United States)

    Dyson, A. E.; Thornton, C.; Hooker, S. M.

    2016-09-01

    We describe in detail a low power Compact Marx Bank (CMB) circuit that can provide 20 kV, 500 A pulses of approximately 100-200 ns duration. One application is the generation of capillary discharge plasmas of density ≈1018 cm-3 used in laser plasma accelerators. The CMB is triggered with a high speed solid state switch and gives a high voltage output pulse with a ns scale rise time into a 50 Ω load (coaxial cable) with run at shot repetition rates of ≳1 Hz. This low power requirement means that the circuit can easily be powered by a small lead acid battery and, therefore, can be floated relative to laboratory earth. The CMB is readily scalable and pulses >45 kV are demonstrated in air discharges.

  14. GeV Electron Beams from a Capillary Discharge Guided Laser Plasma Accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Kei; Gonsalves, Anthony; Panasenko, Dmitriy; Lin, Chen; Toth, Csaba; Geddes, Cameron; Schroeder, Carl; Esarey, Eric; Leemans, Wim

    2010-07-08

    Laser plasma acceleration (LPA) up to 1 GeV has been realized at Lawrence Berkeley National Laboratory by using a capillary discharge waveguide. In this paper, the capillary discharge guided LPA system including a broadband single-shot electron spectrometer is described. The spectrometer was designed specifically for LPA experiments and has amomentumacceptance of 0.01 - 1.1 GeV/c with a percent level resolution. Experiments using a 33 mm long, 300 mu m diameter capillary demonstrated the generation of high energy electron beams up to 1 GeV. By de-tuning discharge delay from optimum guiding performance, selftrapping and acceleration were found to be stabilized producing 460 MeV electron beams.

  15. The role of gas composition in plasma-dust structures in RF discharge

    Energy Technology Data Exchange (ETDEWEB)

    Maiorov, S. A., E-mail: maiorov-sa@mail.ru [Prokhorov General Physics Institute, Russian Academy of Sciences, Vavilov st. 38, Moscow 119991 (Russian Federation); Joint Institute for High Temperatures, Russian Academy of Sciences, Izhorskaya st. 13/19, Moscow 127412 (Russian Federation); Kodanova, S. K.; Dosbolayev, M. K.; Ramazanov, T. S.; Bastykova, N. Kh.; Utegenov, A. U. [Institute of Experimental and Theoretical Physics, Al-Farabi Kazakh National University, Al-Farabi 71, Almaty 050040 (Kazakhstan); Golyatina, R. I. [Prokhorov General Physics Institute, Russian Academy of Sciences, Vavilov st. 38, Moscow 119991 (Russian Federation)

    2015-03-15

    The influence of a mixture of light and heavy gases, i.e., helium and argon, on plasma-dust structures in the radiofrequency discharge has been studied. The dust chains in the sheath of the radiofrequency discharge, the average distance between the dust particles and their chains, have been analyzed. A significant effect of small amounts of argon on the correlation characteristics of dust particles has been observed. The results of numerical simulation of ion and electron drift in the mixture of helium and argon are presented. It is shown that even 1% of argon admixture to helium produces such an effect that argon ions become the main components of the discharge, as they drift with lightweight helium forming a strongly anisotropic velocity distribution function.

  16. Removal of caffeine from water by combining dielectric barrier discharge (DBD plasma with goethite

    Directory of Open Access Journals (Sweden)

    Jian Wang

    2017-07-01

    Full Text Available In this research, dielectric barrier discharge plasma was developed to cooperate with goethite for removing caffeine in aqueous solution. Goethite was characterized by X-ray diffraction and scanning electron microscopy. The effects of input power, initial concentration and catalysts concentration on the removal efficiency of caffeine were evaluated. Furthermore, the degradation pathways of caffeine were also discussed preliminarily. In the case of caffeine concentration at 50 mg L−1, the degradation efficiency of caffeine was improved from 41% to 94% after 24 min on the conditions of input power of 75 W by combining goethite catalysts (2.5 g L−1, while the energy efficiency could be enhanced 1.6–2.3 times compared to the single DBD reactor. The reaction mechanism experiments demonstrated that attack by hydroxyl radical and ozone was the main degradation process of caffeine in aqueous solution. These studies also provided a theoretical and practical basis for the application of DBD-goethite in treatment of caffeine from water.

  17. Dechlorination and decomposition of chloroform induced by glow discharge plasma in an aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yongjun, E-mail: lyjglow@sohu.com [College of Environmental Science & Engineering, Dalian Maritime University, Dalian 116026 (China); Brook Byers Institute for Sustainable Systems, Georgia Institute of Technology, Atlanta 30332 (United States); Crittenden, John C. [Brook Byers Institute for Sustainable Systems, Georgia Institute of Technology, Atlanta 30332 (United States); Wang, Lei [College of Environmental Science & Engineering, Xiamen University of Technology, Xiamen 361024 (China); Liu, Panliang [Brook Byers Institute for Sustainable Systems, Georgia Institute of Technology, Atlanta 30332 (United States)

    2016-05-05

    Highlights: • Hydrated electrons played an important role for chloroform decomposition. • Oxygen enhanced hydrolyses are critical for the chloroform mineralization. • Energy efficiency of GDP is higher than those of the typical competitive processes. - Abstract: In this study, efficient dechlorination and decomposition of chloroform (CF) induced by glow discharge plasma (GDP) in contact with a sodium sulfate solution was investigated. Intermediate byproducts were determined by ionic chromatography and headspace gas chromatography, respectively. Results showed that CF can be effectively dechlorinated and decomposed under the action of GDP. Both removal and dechlorination of CF increased with increasing pH and with addition of hydroxyl radical scavengers to the solution. Addition of H{sub 2}O{sub 2} to the solution slightly decreased the CF removal. Formic acid, oxalic acid and dichloromethane were determined as the major intermediate byproducts. Final products were carbon dioxide and hydrochloric acid. Hydrated electrons were the most likely active species responsible for initiation of the dechlorination, and hydroxyl radicals may be the ones for the oxidation of the organic intermediate byproducts. Hydrolyses of the chloromethyl radicals contributed much in the mineralization of the organic chlorine. Reaction mechanism was proposed based on the dechlorination kinetics and the distribution of intermediate byproducts.

  18. STUDENT AWARD FINALIST: Oxygen Pathways in Streamer Discharge for Transient Plasma Ignition

    Science.gov (United States)

    Pendleton, S. J.; Bowman, S.; Singleton, D.; Watrous, J.; Carter, C.; Lempert, W.; Gundersen, M. A.

    2011-10-01

    The use of streamers for the ignition of fuels, also known as transient plasma ignition (TPI), has been shown in a variety of engines to improve combustion through decreased ignition delay, increased lean burn capability and increased energy release relative to conventional spark ignition. The mechanisms behind these improvements, however, remain poorly understood. Temperature measurements by optical emission spectroscopy demonstrate that ignition by TPI is a nonthermal process, and thus is almost entirely dependent on the production and presence of electron impact-created active species in the discharge afterglow. Of particular interest are active oxygen species due to their relatively long lifetimes at high pressures and the pivotal role they play in combustion reactions. In order to elucidate the oxygen pathways, here we report the investigation of the temporal evolution of the populations of atomic oxygen and ozone by use of two-photon absorption laser induced fluorescence (TALIF) and UV absorption, respectively. Experimental results are presented and compared to kinetic modeling of the streamers. Future experiments are proposed to better understand the physics behind TPI. Supported by NSF, AFOSR, NumerEx-ONR, AFRL-WPAFB.

  19. Biodiesel production using fatty acids from food industry waste using corona discharge plasma technology.

    Science.gov (United States)

    Cubas, A L V; Machado, M M; Pinto, C R S C; Moecke, E H S; Dutra, A R A

    2016-01-01

    This article aims to describe an alternative and innovative methodology to transform waste, frying oil in a potential energy source, the biodiesel. The biodiesel was produced from fatty acids, using a waste product of the food industry as the raw material. The methodology to be described is the corona discharge plasma technology, which offers advantages such as acceleration of the esterification reaction, easy separation of the biodiesel and the elimination of waste generation. The best conditions were found to be an oil/methanol molar ratio of 6:1, ambient temperature (25 °C) and reaction time of 110 min and 30 mL of sample. The acid value indicates the content of free fatty acids in the biodiesel and the value obtained in this study was 0.43 mg KOH/g. Peaks corresponding to octadecadienoic acid methyl ester, octadecanoic acid methyl ester and octadecenoic acid methyl ester, from the biodiesel composition, were identified using GC-MS. A major advantage of this process is that the methyl ester can be obtained in the absence of chemical catalysts and without the formation of the co-product (glycerin). Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Skeletal cell differentiation is enhanced by atmospheric dielectric barrier discharge plasma treatment.

    Directory of Open Access Journals (Sweden)

    Marla J Steinbeck

    Full Text Available Enhancing chondrogenic and osteogenic differentiation is of paramount importance in providing effective regenerative therapies and improving the rate of fracture healing. This study investigated the potential of non-thermal atmospheric dielectric barrier discharge plasma (NT-plasma to enhance chondrocyte and osteoblast proliferation and differentiation. Although the exact mechanism by which NT-plasma interacts with cells is undefined, it is known that during treatment the atmosphere is ionized generating extracellular reactive oxygen and nitrogen species (ROS and RNS and an electric field. Appropriate NT-plasma conditions were determined using lactate-dehydrogenase release, flow cytometric live/dead assay, flow cytometric cell cycle analysis, and Western blots to evaluate DNA damage and mitochondrial integrity. We observed that specific NT-plasma conditions were required to prevent cell death, and that loss of pre-osteoblastic cell viability was dependent on intracellular ROS and RNS production. To further investigate the involvement of intracellular ROS, fluorescent intracellular dyes Mitosox (superoxide and dihydrorhodamine (peroxide were used to assess onset and duration after NT-plasma treatment. Both intracellular superoxide and peroxide were found to increase immediately post NT-plasma treatment. These increases were sustained for one hour but returned to control levels by 24 hr. Using the same treatment conditions, osteogenic differentiation by NT-plasma was assessed and compared to peroxide or osteogenic media containing β-glycerolphosphate. Although both NT-plasma and peroxide induced differentiation-specific gene expression, neither was as effective as the osteogenic media. However, treatment of cells with NT-plasma after 24 hr in osteogenic or chondrogenic media significantly enhanced differentiation as compared to differentiation media alone. The results of this study show that NT-plasma can selectively initiate and amplify ROS

  1. Skeletal cell differentiation is enhanced by atmospheric dielectric barrier discharge plasma treatment.

    Science.gov (United States)

    Steinbeck, Marla J; Chernets, Natalie; Zhang, Jun; Kurpad, Deepa S; Fridman, Gregory; Fridman, Alexander; Freeman, Theresa A

    2013-01-01

    Enhancing chondrogenic and osteogenic differentiation is of paramount importance in providing effective regenerative therapies and improving the rate of fracture healing. This study investigated the potential of non-thermal atmospheric dielectric barrier discharge plasma (NT-plasma) to enhance chondrocyte and osteoblast proliferation and differentiation. Although the exact mechanism by which NT-plasma interacts with cells is undefined, it is known that during treatment the atmosphere is ionized generating extracellular reactive oxygen and nitrogen species (ROS and RNS) and an electric field. Appropriate NT-plasma conditions were determined using lactate-dehydrogenase release, flow cytometric live/dead assay, flow cytometric cell cycle analysis, and Western blots to evaluate DNA damage and mitochondrial integrity. We observed that specific NT-plasma conditions were required to prevent cell death, and that loss of pre-osteoblastic cell viability was dependent on intracellular ROS and RNS production. To further investigate the involvement of intracellular ROS, fluorescent intracellular dyes Mitosox (superoxide) and dihydrorhodamine (peroxide) were used to assess onset and duration after NT-plasma treatment. Both intracellular superoxide and peroxide were found to increase immediately post NT-plasma treatment. These increases were sustained for one hour but returned to control levels by 24 hr. Using the same treatment conditions, osteogenic differentiation by NT-plasma was assessed and compared to peroxide or osteogenic media containing β-glycerolphosphate. Although both NT-plasma and peroxide induced differentiation-specific gene expression, neither was as effective as the osteogenic media. However, treatment of cells with NT-plasma after 24 hr in osteogenic or chondrogenic media significantly enhanced differentiation as compared to differentiation media alone. The results of this study show that NT-plasma can selectively initiate and amplify ROS signaling to enhance

  2. Experimental investigation of surface roughness in electrical discharge turning process

    Science.gov (United States)

    Gohil, Vikas; Puri, Y. M.

    2016-10-01

    In the present study the effects of machining parameters on the average surface roughness (Ra) in electrical discharge turning (EDT) is investigated. EDT is a new machining process in which a rotary spindle is added to a conventional die-sinking EDM machine in order to produce cylindrical components. In this method a new process parameter (spindle rotation) along with pulse on time and current is introduced to study its effect on Ra. This has been done by means of full factorial design (21 × 32) of experiments. A mathematical model has been developed for Ra by regression analysis and factor effects were analyzed using analysis of variance (ANOVA). Signal-to-noise ratio analysis is used to find the optimal condition.

  3. OPTIMISATION OF DIELECTRIC BARRIER DISCHARGE PLASMA ACTUATORS AND THEIR APPLICATION TO FLUID DYNAMICS

    OpenAIRE

    Erfani, Rasool

    2012-01-01

    The standard dielectric barrier discharge (DBD) plasma actuator, in which an asymmetric arrangement of electrodes leads to momentum coupling into the surrounding air, has already demonstrated its capability for flow control. The effect of some parameters such as dielectric thickness, dielectric temperature, voltage amplitude, driving frequency, different configurations and arrangements on actuator performance are examined. The new configuration of DBD which uses multiple encapsulated electrod...

  4. Surface studies of plasma processed Nb samples

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, Puneet V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Doleans, Marc [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Hannah, Brian S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Afanador, Ralph [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Stewart, Stephen [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Mammosser, John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Howell, Matthew P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Saunders, Jeffrey W [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Degraff, Brian D [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS); Kim, Sang-Ho [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Spallation Neutron Source (SNS)

    2015-01-01

    Contaminants present at top surface of superconducting radio frequency (SRF) cavities can act as field emitters and restrict the cavity accelerating gradient. A room temperature in-situ plasma processing technology for SRF cavities aiming to clean hydrocarbons from inner surface of cavities has been recently developed at the Spallation Neutron Source (SNS). Surface studies of the plasma-processed Nb samples by Secondary ion mass spectrometry (SIMS) and Scanning Kelvin Probe (SKP) showed that the NeO2 plasma processing is very effective to remove carbonaceous contaminants from top surface and improves the surface work function by 0.5 to 1.0 eV.

  5. Space plasma physics: I - Stationary processes

    Science.gov (United States)

    Hasegawa, Akira; Sato, Tetsuya

    1989-01-01

    The physics of stationary processes in space plasmas is examined theoretically in an introduction intended for graduate students. The approach involves the extensive use of numerical simulations. Chapters are devoted to fundamental principles, small-amplitude waves, and the stationary solar plasma system; typical measurement data and simulation results are presented graphically.

  6. Developments in Plasma Processes for Extractive Metallurgy

    Science.gov (United States)

    Gauvin, W. H.; Drouet, M. G.; Munz, R. J.

    1987-12-01

    With the recent availability of commercial plasma-generating devices capable of reliable performance at powers as high as 30 MW, the applications of plasma technology in high-temperature extractive metallurgy are rapidly increasing. Some of the more promising process developments are reviewed in this paper, as are newer reactor designs.

  7. Effect of a floating circular aperture on a dc glow discharge dusty plasma

    Science.gov (United States)

    Heinrich, Jonathon R.; Kim, Su-Hyun; Merlino, Robert L.

    2009-11-01

    We have investigated novel effects observed when a floating aperture, either 6 mm or 8 mm in diameter, is placed 1-2 cm in front of an anode disk (4 cm diameter) that is used to form a dc glow discharge dusty plasma. Dust is incorporated into the anode glow plasma from a tray located below the anode which contained kaolin powder. The glow discharge traps particles with an average size of 1 micron. When the aperture is placed in front of the disk, well-defined pear-shaped or spherical dust clouds are formed, depending on the diameter of the aperture and its distance from the anode. The dust interacts with the aperture through the potential structure associated with the floating (negative) plate in which the aperture is located. The dust cloud is imaged using a CCD camera and a thin sheet of 532 nm laser light. Some of the effects observed include: outwardly expanding spherical dust acoustic waves and shocks, dust rotation around a void formed at the aperture, and a dust/discharge instability in which the discharge is periodically quenched and reignited while the dust cloud expands and contracts, with the dust retaining a residual charge.

  8. Comparative study of non-thermal atmospheric pressure discharge plasmas for life science applications

    Science.gov (United States)

    Koga, Kazunori; Katayama, Ryu; Sarinont, Thapanut; Seo, Hyunwoong; Itagaki, Naho; Attri, Pankaj; Leal-Quiros, Edbertho; Tanaka, Akiyo; Shiratani, Masaharu

    2016-09-01

    We are comparing several non-thermal atmospheric pressure discharge plasmas for life science applications. Here we measured discharge period dependence of pH value and 750 nm absorbance of KI-starch solution of deionized water after plasma irradiation with two discharge devices; a dielectric barrier discharge (DBD) jet device and a scalable DBD device. The pH and the absorbance of KI-starch solution are useful indicator of their oxidizability. We have obtained a map of the absorbance and proton concentration [H+] which is deduced from pH value. For the scalable DBD, the range of the absorbance is between 0.7 and 1.3 and that of [H+] is between 10-7 and 10-5 mol/L. For the DBD jet, the range of the absorbance and [H+] are 2.0-3.2 and 10-4-10-3 mol/L, respectively. Measured data for both devices shows same tendency in the map, while the range of values for the scalable DBD is smaller than that for the DBD jet. The results indicate the oxidazability for the scalable DBD is much weaker than that for the DBD jet.

  9. Energy deposition characteristics of nanosecond dielectric barrier discharge plasma actuators: Influence of dielectric material

    Science.gov (United States)

    Correale, G.; Winkel, R.; Kotsonis, M.

    2015-08-01

    An experimental study aimed at the characterization of energy deposition of nanosecond Dielectric Barrier Discharge (ns-DBD) plasma actuators was carried out. Special attention was given on the effect of the thickness and material used for dielectric barrier. The selected materials for this study were polyimide film (Kapton), polyamide based nylon (PA2200), and silicone rubber. Schlieren measurements were carried out in quiescent air conditions in order to observe density gradients induced by energy deposited. Size of heated area was used to qualify the energy deposition coupled with electrical power measurements performed using the back-current shunt technique. Additionally, light intensity measurements showed a different nature of discharge based upon the material used for barrier, for a fixed thickness and frequency of discharge. Finally, a characterisation study was performed for the three tested materials. Dielectric constant, volume resistivity, and thermal conductivity were measured. Strong trends between the control parameters and the energy deposited into the fluid during the discharge were observed. Results indicate that efficiency of energy deposition mechanism relative to the thickness of the barrier strongly depends upon the material used for the dielectric barrier itself. In general, a high dielectric strength and a low volumetric resistivity are preferred for a barrier, together with a high heat capacitance and a low thermal conductivity coefficient in order to maximize the efficiency of the thermal energy deposition induced by an ns-DBD plasma actuator.

  10. Non-Thermal Equilibrium Atmospheric Pressure Glow-Like Discharge Plasma Jet

    Science.gov (United States)

    Chang, Zhengshi; Yao, Congwei; Zhang, Guanjun

    2016-01-01

    Non-thermal equilibrium atmospheric pressure plasma jet (APPJ) is a cold plasma source that promises various innovative applications, and the uniform APPJ is more favored. Glow discharge is one of the most effective methods to obtain the uniform discharge. Compared with the glow dielectric barrier discharge (DBD) in atmospheric pressure, pure helium APPJ shows partial characteristics of both the glow discharge and the streamer. In this paper, considering the influence of the Penning effect, the electrical and optical properties of He APPJ and Ar/NH3 APPJ were researched. A word “Glow-like APPJ” is used to characterize the uniformity of APPJ, and it was obtained that the basic characteristics of the glow-like APPJ are driven by the kHz AC high voltage. The results can provide a support for generating uniform APPJ, and lay a foundation for its applications. supported by National Natural Science Foundation of China (Nos. 51307133, 51125029, 51221005) and the Fundamental Research Funds for the Central Universities of China (Nos. xjj2012132, xkjc2013004)

  11. Comparison endpoint study of process plasma and secondary electron beam exciter optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Stephan Thamban, P. L.; Yun, Stuart; Padron-Wells, Gabriel; Hosch, Jimmy W.; Goeckner, Matthew J. [Department of Mechanical Engineering, University of Texas at Dallas, 800W Campbell Road, Richardson, Texas 75080 (United States); Department of Electrical Engineering, University of Texas at Dallas, 800W Campbell Road, Richardson, Texas 75080 (United States); Verity Instruments, Inc., 2901 Eisenhower Street, Carrollton, Texas 75007 (United States); Department of Mathematical Sciences, University of Texas at Dallas, 800 W Campbell Road, Richardson, Texas 75080 (United States)

    2012-11-15

    Traditionally process plasmas are often studied and monitored by optical emission spectroscopy. Here, the authors compare experimental measurements from a secondary electron beam excitation and direct process plasma excitation to discuss and illustrate its distinctiveness in the study of process plasmas. They present results that show excitations of etch process effluents in a SF{sub 6} discharge and endpoint detection capabilities in dark plasma process conditions. In SF{sub 6} discharges, a band around 300 nm, not visible in process emission, is observed and it can serve as a good indicator of etch product emission during polysilicon etches. Based on prior work reported in literature the authors believe this band is due to SiF{sub 4} gas phase species.

  12. The ozonizer discharge as a gas-phase advanced oxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Rosocha, L.A.

    1997-09-01

    In the past several years, there has been increased interest in gas-phase pollution control arising from a larger body of environmental regulations and a greater respect for the environment. One promising class of pollution-control technologies is that called advanced oxidation processes (AOPs). Ozonizers have been used for over a century in water treatment and for about two decades in advanced oxidation. Ozonizers are fundamentally based on non-thermal plasmas, which are useful for generating reactive species (free radicals) in gas streams. Because radical-attack reaction rate constants are very large for many chemical species, entrained pollutants are readily decomposed by these radicals. Non-thermal plasmas can generate both oxidative and reductive radicals; therefore, they show promise for treating a wide variety of pollutants. However, this application is only about a decade old, so more work is needed for optimizing and commercializing the process. This paper is intended to serve as an introduction to the subject of pollutant decomposition with the nonthermal plasmas generated by ozonizer discharges. Basic plasma and decomposition chemistry, laboratory experiments, and example applications are discussed.

  13. Three-dimensional modeling of the neutral gas depletion effect in a helicon discharge plasma

    Science.gov (United States)

    Kollasch, Jeffrey; Schmitz, Oliver; Norval, Ryan; Reiter, Detlev; Sovinec, Carl

    2016-10-01

    Helicon discharges provide an attractive radio-frequency driven regime for plasma, but neutral-particle dynamics present a challenge to extending performance. A neutral gas depletion effect occurs when neutrals in the plasma core are not replenished at a sufficient rate to sustain a higher plasma density. The Monte Carlo neutral particle tracking code EIRENE was setup for the MARIA helicon experiment at UW Madison to study its neutral particle dynamics. Prescribed plasma temperature and density profiles similar to those in the MARIA device are used in EIRENE to investigate the main causes of the neutral gas depletion effect. The most dominant plasma-neutral interactions are included so far, namely electron impact ionization of neutrals, charge exchange interactions of neutrals with plasma ions, and recycling at the wall. Parameter scans show how the neutral depletion effect depends on parameters such as Knudsen number, plasma density and temperature, and gas-surface interaction accommodation coefficients. Results are compared to similar analytic studies in the low Knudsen number limit. Plans to incorporate a similar Monte Carlo neutral model into a larger helicon modeling framework are discussed. This work is funded by the NSF CAREER Award PHY-1455210.

  14. Space charge, plasma potential and electric field distributions in HiPIMS discharges of varying configuration

    Science.gov (United States)

    Liebig, B.; Bradley, J. W.

    2013-08-01

    An electron-emitting (emissive) probe has been used to study the temporal and spatial distribution of the plasma potential during high-power impulse magnetron sputtering (HiPIMS) discharges with various substrate and magnetic field configurations. The average power was 700 W, with a repetition frequency of 100 Hz and pulse duration of 100 µs. Strongly negative plasma potentials exceeding -300 V and electric fields up to 10 kV m-1, caused by strong separation of charges with net charge carrier densities Δn of about 1014 m-3, were observed during the ignition of the discharge. The spatial distribution of the plasma potential in the stable stage of the discharge showed values consistently 5 V more negative for a floating substrate compared with a grounded one, so enhancing electron transport around the insulated substrate to grounded walls. However, this change in the electrical configuration of the plasma does not alter significantly the fraction of ionized sputtered particles (of about 30%) that can potentially reach the substrate. By changing the degree of unbalance of the sputtering source, we find a strong correlation between the electric field strength in the magnetic trap (created through charge separation) and the absolute value (and shape) of the magnetic field. For the more unbalanced magnetron, a flattening of the plasma potential structure (decrease in the axial electric field) was observed close to the target. Our findings show in principle that manipulation of the potential barrier close to the target through changing the magnetic field can regulate the proportion of sputtered and ionized species reaching the substrate.

  15. INPROVING OF THE QUALITY FOOD FOR ANIMALS BY PULSED POWER PLASMA DISCHARGE

    Directory of Open Access Journals (Sweden)

    Sebastian Gnapowski

    2015-08-01

    Full Text Available Soy beans powder mixed with water is a good food for animals. However, there are two problems with this brew. One is that soy beans powder is sunk down to fast. Parts of soy beans powder are too big and too heavy. Animals do not eat soy beans powder because after a few minutes (around 3min is sunk down and soy beans are on the bottom case. Another negative point is a quick growth of mold, especially during summer when the temperature is highest. Mold is making food unhealthy and causes unpleasant smell. After mold appears it is difficult to clean the case. One of the solutions to eliminate these problems is to use pulse power plasma discharge and the second solution is ultra sound treatment. It was observed that pulse power discharge can decrease the size of soy beans powder a few times. Another advantage of such experiments was that the pulse power discharge killed bacteria and viruses. After our experiments we did not observe mold growing. Using pulse power discharge we can decrease sinking speed by about ten times. Ultra sound generation is useful and can decrease sinking speed even more, compared with pulse power discharge.

  16. Surface modification of chitosan/PEO nanofibers by air dielectric barrier discharge plasma for acetylcholinesterase immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Dorraki, Naghme, E-mail: n.dorraki@web.sbu.ac.ir [Laser and Plasma Research Institute, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Safa, Nasrin Navab [Laser and Plasma Research Institute, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Jahanfar, Mehdi [Protein Research Center, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Ghomi, Hamid [Laser and Plasma Research Institute, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Ranaei-Siadat, Seyed-Omid [Protein Research Center, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of)

    2015-09-15

    Highlights: • We used an economical and effective method for surface modification. • Chitosan/PEO nanofibrous membranes were modified by air-DBD plasma. • The most NH{sub 3}{sup +} group was generated on the 6 min plasma modified membrane. • We immobilized acetylcholinesterase on the plasma modified and unmodified membranes. • More enzyme activity was detected on the modified membrane by plasma. - Abstract: There are different methods to modify polymer surfaces for biological applications. In this work we have introduced air-dielectric barrier discharge (DBD) plasma at atmospheric pressure as an economical and safe method for modifying the surface of electrospun chitosan/PEO (90/10) nanofibers for acetylcholinesterase (AChE) immobilization. According to the contact angle measurement results, the nanofibers become highly hydrophilic when they are exposed to the DBD plasma for 6 min in compared to unmodified membrane. Attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) results reveal hydroxyl, C=O and NH{sub 3}{sup +} polar groups increment after 6 min plasma treatment. Contact angle measurements and ATR-FTIR results are confirmed by X-ray photoelectron spectroscopy (XPS). AChE at pH 7.4 carries a negative charge and after immobilization on the surface of plasma-treated nanofibrous membrane attracts the NH{sub 3}{sup +} group and more enzyme activity is detected on the plasma-modified nanofibers for 6 min in compared to unmodified nanofibers. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) are used for the surface topography and morphology characterization. The results have proved that air-DBD plasma is a suitable method for chitosan/PEO nanofibrous membrane modification as a biodegradable and functionalized substrate for enzyme immobilization.

  17. A Method for Measurement of Dynamic Sheath Behavior in Plasma Immersion Ion Implantation and Deposition Process

    Institute of Scientific and Technical Information of China (English)

    WU Hongchen; MA Guojia; PENG Liping; FENG Jianji; ZHANG Huafang; MA Tengcai

    2008-01-01

    A method to measure temporal and spatial evolution of sheath in plasma immersion ion implantation (PⅢ) process is presented.A long Langrnuir probe (φ 5 mm×φ 78 mm) with low bias is used to detect the sheath propagation and backup with time.The aubstrate made of Al cylinder (φ20 mm×φ150 mm) is immersed in nitrogen and argon plasma induced by magnetron self-sustained discharge.The maximum sheath sizes,at different plasma densities under different discharge currents,are measured and compared.

  18. Nanosecond Pulsed Discharge in Water without Bubbles: A Fundamental Study of Initiation, Propagation and Plasma Characteristics

    Science.gov (United States)

    Seepersad, Yohan

    The state of plasma is widely known as a gas-phase phenomenon, but plasma in liquids have also received significant attention over the last century. Generating plasma in liquids however is theoretically challenging, and this problem is often overcome via liquid-gas phase transition preceding the actual plasma formation. In this sense, plasma forms in gas bubbles in the liquid. Recent work at the Drexel Plasma Institute has shown that nanosecond pulsed electric fields can initiate plasma in liquids without any initial cavitation phase, at voltages below theoretical direct-ionization thresholds. This unique regime is poorly understood and does not fit into any current descriptive mechanisms. As with all new phenomena, a complete fundamental description is paramount to understanding its usefulness to practical applications. The primary goals of this research were to qualitatively and quantitatively understand the phenomenon of nanosecond pulsed discharge in liquids as a means to characterizing properties that may open up niche application possibilities. Analysis of the plasma was based on experimental results from non-invasive, sub-nanosecond time-resolved optical diagnostics, including direct imaging, transmission imaging (Schlieren and shadow), and optical emission spectroscopy. The physical characteristics of the plasma were studied as a function of variations in the electric field amplitude and polarity, liquid permittivity, and pulse duration. It was found that the plasma size and emission intensity was dependent on the permittivity of the liquid, as well as the voltage polarity, and the structure and dynamics were explained by a 'cold-lightning' mechanism. The under-breakdown dynamics at the liquid-electrode interface were investigated by transmission imaging to provide evidence for a novel mechanism for initiation based on the electrostriction. This mechanism was proposed by collaborators on the project and developed alongside the experimental work in this

  19. Observation of plasma jets in a table top plasma focus discharge

    Energy Technology Data Exchange (ETDEWEB)

    Pavez, Cristian; Soto, Leopoldo, E-mail: lsoto@cchen.cl [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Center for Research and Applications in Plasma Physics and Pulsed Power, P4, Santiago-Talca (Chile); Departamento de Ciencias Físicas, Facultad de Ciencias Exactas, Universidad Andrés Bello, República 220, Santiago (Chile); Pedreros, José [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Departamento de Ingeniería Eléctrica, Universidad de Santiago de Chile, Santiago (Chile); Tarifeño-Saldivia, Ariel [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Center for Research and Applications in Plasma Physics and Pulsed Power, P4, Santiago-Talca (Chile)

    2015-04-15

    In the last years, medium size Z-pinch experiments operating at tens of kJ are being used to create supersonic plasma jets. Those experiments are produced with wire arrays and radial foils, and they are conducted in generators based on water-filled transmission lines. Also plasma jets have been observed in small X-pinch experiments operating at 1 kJ. In this work, observations of plasma jets produced in a table top plasma focus device by means of optical and digital interferometry are shown. The device was operated at only ∼70 J, achieving 50 kA in 150 ns. The plasma jets were observed after the pinch, in the region close and on the anode, along the axis. The electron density measured from the jets is in the range 10{sup 24}–10{sup 25 }m{sup −3}. From two consecutive plasma images separated 18 ns, the axial jet velocity was measured in the order of 4 × 10{sup 4 }m/s.

  20. Near Discharge Cathode Assembly Plasma Potential Measurements in a 30-cm NSTAR Type Ion Engine During Beam Extraction

    Science.gov (United States)

    Herman, Daniel A.; Gallimore, Alec D.

    2006-01-01

    Floating emissive probe plasma potential data are presented over a two-dimensional array of locations in the near Discharge Cathode Assembly (DCA) region of a 30-cm diameter ring-cusp ion thruster. Discharge plasma data are presented with beam extraction at throttling conditions comparable to the NASA TH Levels 8, 12, and 15. The operating conditions of the Extended Life Test (ELT) of the Deep Space One (DS1) flight spare ion engine, where anomalous discharge keeper erosion occurred, were TH 8 and TH 12 consequently they are of specific interest in investigating discharge keeper erosion phenomena. The data do not validate the presence of a potential hill plasma structure downstream of the DCA, which has been proposed as a possible erosion mechanism. The data are comparable in magnitude to data taken by other researchers in ring-cusp electron-bombardment ion thrusters. The plasma potential structures are insensitive to thruster throttling level with a minimum as low as 14 V measured at the DCA exit plane and increasing gradually in the axial direction. A sharp increase in plasma potential to the bulk discharge value of 26 to 28 volts, roughly 10 mm radially from DCA centerline, was observed. Plasma potential measurements indicate a low-potential plume structure that is roughly 20 mm in diameter emanating from the discharge cathode that may be attributed to a free-standing plasma double layer.

  1. Control of Reactive Species Generated by Low-frequency Biased Nanosecond Pulse Discharge in Atmospheric Pressure Plasma Effluent

    Science.gov (United States)

    Takashima, Keisuke; Kaneko, Toshiro

    2016-09-01

    The control of hydroxyl radical and the other gas phase species generation in the ejected gas through air plasma (air plasma effluent) has been experimentally studied, which is a key to extend the range of plasma treatment. Nanosecond pulse discharge is known to produce high reduced electric field (E/N) discharge that leads to efficient generation of the reactive species than conventional low frequency discharge, while the charge-voltage cycle in the low frequency discharge is known to be well-controlled. In this study, the nanosecond pulse discharge biased with AC low frequency high voltage is used to take advantages of these discharges, which allows us to modulate the reactive species composition in the air plasma effluent. The utilization of the gas-liquid interface and the liquid phase chemical reactions between the modulated long-lived reactive species delivered from the air plasma effluent could realize efficient liquid phase chemical reactions leading to short-lived reactive species production far from the air plasma, which is crucial for some plasma agricultural applications.

  2. Nanosecond pulsed dielectric barrier discharge plasma-catalytic removal of HCHO in humid air

    Science.gov (United States)

    Zhang, Shuai; Wang, Wenchun; Zhang, Li; Zhao, Zilu; Yang, Dezheng

    2017-05-01

    Non-thermal plasma (NTP) has been regarded as a promising method for the removal of a wide range of low concentration volatile organic compounds (VOCs). In this paper, nanosecond pulsed and alternating current dielectric barrier discharge plasmas synergistic catalyst are utilized for removal of formaldehyde (HCHO) in humid air. Working gas is 1% H2O/21% O2/78% N2 with 154 ppm HCHO over total flow rate of 50 mL/min. Specific energy density (SED) are 32.5 JL-1, 35.8 JL-1 and 1069.2 JL-1 at power consumption of 0.325 W, 0.3 W, 8.9 W for removal of 67%, 63.8% and 73.8% HCHO when using bipolar nanosecond pulsed, unipolar nanosecond pulsed and AC dielectric barrier discharge (DBD) plasma, respectively. The removal efficiencies of HCHO using nanosecond pulsed DBD plasma increase approximately 10 20% when the packed-bed Al2O3 pellets exist and can reach up to almost 100% when TiO2 nanoparticles are used while the effect of CeO2 nanoparticles is a bit poor. Analysis indicate that OH radical and O atom play main role for removal HCHO and the gas temperature is a significant factor for its influence on rate constants of HCHO with active particles.

  3. Electron beam generated plasmas for the processing of graphene

    Science.gov (United States)

    Walton, S. G.; Hernández, S. C.; Boris, D. R.; Petrova, Tz B.; Petrov, G. M.

    2017-09-01

    The Naval Research Laboratory (NRL) has developed a processing system based on an electron beam-generated plasma and applied it to the processing of graphene. Unlike conventional discharges produced by electric fields (DC, RF, microwave, etc), the plasma is driven by a high-energy (~few keV) electron beam, an approach that simplifies the relative production of species while providing comparatively high ion-to-radical production rates. The resulting plasmas are characterized by high charged particle densities (1010-1011 cm-3) and electron temperatures that are typically about 1.0 eV or lower. Accordingly, the flux to adjacent surfaces is generally dominated by ions with kinetic energies in the range of 1-5 eV, a value at or near the bond strength of most materials. This provides the potential for controllably engineering materials with monolayer precision, an attribute attractive for the processing of atomically thin material systems. This work describes the attributes of electron beam driven plasma processing system and its use in modification of graphene.

  4. Experimental research of pulsed discharge plasma and TiO2/Zeolite coupling technology for formaldehyde removal

    Science.gov (United States)

    Dong, Bingyan; Lan, Shuirong

    2013-03-01

    The pulsed discharge plasma combining with catalyst to remove formaldehyde is a novel type of advanced oxidation technology. In the present work, taking wire-tube pulsed discharge plasma and TiO2/Zeolite coupling technology for formaldehyde removal. The studies have investigated the wire-tube reactor with zeolite, TiO2, TiO2/Zeolite for formaldehyde removal respectively. Results show that in the optimal experimental conditions and the baking time is 120 min, the baking temperature is 450 °C, that TiO2/Zeolite catalyst which made by sol-gel shows higher photocatalytic activity and efficiency. The pulsed discharge with TiO2/Zeolite catalyst for formaldehyde removal has higher removal efficiency than pulsed discharge with zeolite or TiO2. Therefore, pulsed discharge plasma with TiO2/Zeolite for the removal of formaldehyde can greatly increase the removal efficiency.

  5. Plasma-photocatalyst interaction: Production of oxygen atoms in a low pressure discharge

    Science.gov (United States)

    Guaitella, O.; Gatilova, L.; Rousseau, A.

    2005-04-01

    A pulsed dc low pressure discharge in air (210 Pa) is used to study the mechanisms of activation of a photocatalytic material (TiO2) under plasma exposure. It is first shown that the presence of TiO2 inside the plasma region leads to a strong increase of the reduced electric field. Time resolved measurement of the atomic oxygen density is performed by actinometry during a 10 ms pulse at a low repetition rate (1 Hz) with and without TiO2 pellets inside the plasma region. The presence of TiO2 pellets strongly increases the O atom density during the first millisecond, but this effect saturates for longer exposure times.

  6. Fundamental Processes in Plasmas. Final report

    Energy Technology Data Exchange (ETDEWEB)

    O' Neil, Thomas M.; Driscoll, C. Fred

    2009-11-30

    This research focuses on fundamental processes in plasmas, and emphasizes problems for which precise experimental tests of theory can be obtained. Experiments are performed on non-neutral plasmas, utilizing three electron traps and one ion trap with a broad range of operating regimes and diagnostics. Theory is focused on fundamental plasma and fluid processes underlying collisional transport and fluid turbulence, using both analytic techniques and medium-scale numerical simulations. The simplicity of these systems allows a depth of understanding and a precision of comparison between theory and experiment which is rarely possible for neutral plasmas in complex geometry. The recent work has focused on three areas in basic plasma physics. First, experiments and theory have probed fundamental characteristics of plasma waves: from the low-amplitude thermal regime, to inviscid damping and fluid echoes, to cold fluid waves in cryogenic ion plasmas. Second, the wide-ranging effects of dissipative separatrices have been studied experimentally and theoretically, finding novel wave damping and coupling effects and important plasma transport effects. Finally, correlated systems have been investigated experimentally and theoretically: UCSD experients have now measured the Salpeter correlation enhancement, and theory work has characterized the 'guiding center atoms of antihydrogen created at CERN.

  7. Saturn Plasma Sources and Associated Transport Processes

    Science.gov (United States)

    Blanc, M.; Andrews, D. J.; Coates, A. J.; Hamilton, D. C.; Jackman, C. M.; Jia, X.; Kotova, A.; Morooka, M.; Smith, H. T.; Westlake, J. H.

    2015-10-01

    This article reviews the different sources of plasma for Saturn's magnetosphere, as they are known essentially from the scientific results of the Cassini-Huygens mission to Saturn and Titan. At low and medium energies, the main plasma source is the H2O cloud produced by the "geyser" activity of the small satellite Enceladus. Impact ionization of this cloud occurs to produce on the order of 100 kg/s of fresh plasma, a source which dominates all the other ones: Titan (which produces much less plasma than anticipated before the Cassini mission), the rings, the solar wind (a poorly known source due to the lack of quantitative knowledge of the degree of coupling between the solar wind and Saturn's magnetosphere), and the ionosphere. At higher energies, energetic particles are produced by energy diffusion and acceleration of lower energy plasma produced by the interchange instabilities induced by the rapid rotation of Saturn, and possibly, for the highest energy range, by contributions from the CRAND process acting inside Saturn's magnetosphere. Discussion of the transport and acceleration processes acting on these plasma sources shows the importance of rotation-induced radial transport and energization of the plasma, and also shows how much the unexpected planetary modulation of essentially all plasma parameters of Saturn's magnetosphere remains an unexplained mystery.

  8. Particle Densities of the Atmospheric-Pressure Argon Plasmas Generated by the Pulsed Dielectric Barrier Discharges

    Science.gov (United States)

    Pan, Jie; Li, Li; Wang, Yunuan; Xiu, Xianwu; Wang, Chao; Song, Yuzhi

    2016-11-01

    Atmospheric-pressure argon plasmas have received increasing attention due to their high potential in many industrial and biomedical applications. In this paper, a 1-D fluid model is used for studying the particle density characteristics of the argon plasmas generated by the pulsed dielectric barrier discharges. The temporal evolutions of the axial particle density distributions are illustrated, and the influences of changing the main discharge conditions on the averaged particle densities are researched by independently varying the various discharge conditions. The calculation results show that the electron density and the ion density reach two peaks near the momentary cathodes during the rising and the falling edges of the pulsed voltage. Compared with the charged particle densities, the densities of the resonance state atom Arr and the metastable state atom Arm have more uniform axial distributions, reach higher maximums and decay more slowly. During the platform of the pulsed voltage and the time interval between the pulses, the densities of the excited state atom Ar* are far lower than those of the Arr or the Arm. The averaged particle densities of the different considered particles increase with the increases of the amplitude and the frequency of the pulsed voltage. Narrowing the discharge gap and increasing the relative dielectric constant of the dielectric also contribute to the increase of the averaged particle densities. The effects of reducing the discharge gap distance on the neutral particle densities are more significant than the influences on the charged particle densities. supported by Natural Science Foundation of Shandong Province, China (No. ZR2015AQ008), and Project of Shandong Province Higher Educational Science and Technology Program of China (No. J15LJ04)

  9. Dusty plasma microparticle cloud control and rapid electrostatic mutual-repulsion expansion in a DC glow discharge

    Science.gov (United States)

    Gillman, Eric; Amatucci, Bill

    2016-10-01

    Microparticles in plasma discharges rapidly charge up, typically collecting a net negative charge due to the relatively high mobility of electrons compared to ions. Electrostatic forces can be utilized to control charged microparticle behavior and motion in a plasma discharge. In these experiments a metal wire loop is supplied with an electric potential that can be controlled independently from the DC plasma glow discharge electrodes. By varying the voltage on the wire loop, we can attract, trap, manipulate, suspend, and/or repel microparticles that originate from the DC glow discharge. Experiments studied the properties of electrostatic self-repulsion of a cloud of charged microparticles. By pulsing the plasma and controlling wire loop potential, a cloud of trapped microparticles is released and allowed to rapidly expand. A simple force balance simulation code is used as a model to compare and benchmark actual experimental results. This work was supported by the Naval Research Laboratory base program.

  10. Plasma inactivation of microorganisms on sprout seeds in a dielectric barrier discharge.

    Science.gov (United States)

    Butscher, Denis; Van Loon, Hanne; Waskow, Alexandra; Rudolf von Rohr, Philipp; Schuppler, Markus

    2016-12-05

    Fresh produce is frequently contaminated by microorganisms, which may lead to spoilage or even pose a threat to human health. In particular sprouts are considered to be among the most risky foods sold at retail since they are grown in an environment practically ideal for growth of bacteria and usually consumed raw. Because heat treatment has a detrimental effect on the germination abilities of sprout seeds, alternative treatment technologies need to be developed for microbial inactivation purposes. In this study, non-thermal plasma decontamination of sprout seeds is evaluated as a promising option to enhance food safety while maintaining the seed germination capabilities. In detail, investigations focus on understanding the efficiency of non-thermal plasma inactivation of microorganisms as influenced by the type of microbial contamination, substrate surface properties and moisture content, as well as variations in the power input to the plasma device. To evaluate the impact of these parameters, we studied the reduction of native microbiota or artificially applied E. coli on alfalfa, onion, radish and cress seeds exposed to non-thermal plasma in an atmospheric pressure pulsed dielectric barrier discharge streamed with argon. Plasma treatment resulted in a maximum reduction of 3.4 logarithmic units for E. coli on cress seeds. A major challenge in plasma decontamination of granular food products turned out to be the complex surface topology, where the rough surface with cracks and crevices can shield microorganisms from plasma-generated reactive species, thus reducing the treatment efficiency. However, improvement of the inactivation efficiency was possible by optimizing substrate characteristics such as the moisture level and by tuning the power supply settings (voltage, frequency) to increase the production of reactive species. While the germination ability of alfalfa seeds was considerably decreased by harsh plasma treatment, enhanced germination was observed under

  11. Laser diagnostics on atmospheric pressure discharge plasmas, including cryoplasmas, in environments around room and cryogenic temperature

    Science.gov (United States)

    Sakakibara, Noritaka; Muneoka, Hitoshi; Urabe, Keiichiro; Yasui, Ryoma; Sakai, Osamu; Terashima, Kazuo

    2017-04-01

    Cryoplasmas, the plasma gas temperature (T g) of which can be controlled continuously below room temperature, show various unique and advantageous properties depending on T g. Recently, the T g dependence of plasma chemistry related to metastable helium (Hem) has been revealed in helium cryoplasmas. However, T g was only estimated by thermal calculation from the temperature outside the plasmas. In this study, for better evaluation of T g, near-infrared laser heterodyne interferometry (NIR-LHI) measurements were conducted in atmospheric pressure helium pulsed discharge plasmas at around room and cryogenic ambient temperatures (T a). The maximum difference between T g and T a was evaluated as 47 K at T a  =  300 K with 282 mW power consumption. To further investigate the T g dependence of plasma chemical reactions related to Hem, laser absorption spectroscopy (LAS) was performed on the same discharge plasmas to measure the Hem density and lifetime. The Hem lifetime was longer at lower T g, i.e. the lifetime at T g  =  145 K (9.6 µs) was seven times longer than that at T g  =  386 K (1.4 µs). By comparing the results with the numerically simulated rates of Hem quenching reactions taking T g into account, the mechanism of the Hem quenching reaction was revealed to vary with T g even though the main quenching reaction was a three-body collision at all T g. In this manner, the combination of NIR-LHI with LAS led directly to the T g dependence of Hem quenching reactions.

  12. Simulation of electrical discharge in a 3.6 Joule miniature plasma focus device using SIMULINK

    Science.gov (United States)

    Jafari, Hossein; Habibi, Morteza

    2014-08-01

    A novel technique has been developed and studied in this paper to simulate the electrical discharge circuit of a 3.6 J miniature plasma focus device (PFD) and investigate the effect of inductance variation on voltage spike and current dip. The technique is based on a correlation between the electrical discharge circuit and plasma dynamics in a very small PFD that operates at the energy of 3.6 J. The simulation inputs include the charging voltage, capacitor bank capacitance, current limiter resistance, by-pass resistance as well as the time-dependent inductance and resistance of the plasma sheath which are calculated by assuming the plasma dynamics as transit times in going from one phase to the next. The variations of the most important elements in the circuit (i.e. the constant and breakdown inductances) and their effects on the current dip are studied in PFDs with low and high constant inductance. The model demonstrated for achieving a good pinch in the PFD, although the total inductance of the system should be low; however there is always an optimum inductance which causes an appropriate pinch. Furthermore, the electrical power produced by the pulsed power supply, the mechanical energy as well as the magnetic energy which are transferred into the plasma tube were obtained from simulation. The graph of electrical power demonstrated a high instantaneous increment in the power transferred into the plasma as one of the greatest advantages of the pulsed power supply. The simulation was performed using software tools within the MATLAB/SIMULINK simulation environment.

  13. Control of endwall secondary flow in a compressor cascade with dielectric barrier discharge plasma actuation

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Three dielectric barrier discharge plasma actuators were mounted at the positions of 20%,40%and 60%of chord length on the endwall in a compressor cascade.The downstream flow field of the cascade has been measured with a mini five-hole pressure probe with and without the plasma actuation.The measured results show that the plasma actuation most effectively reduces total pressure loss and flow blockage when the actuators are operated simultaneously.As each of the actuators is operated independently,the actuator at the position of 20%of chord length most effectively reduces flow blockage, and the actuator at the position of 60%of chord length fairly reduces total pressure loss.However, negative pressure loss reduction occurs with the plasma actuator at the position of 40%of chord length.In brief,the plasma actuation placed on the endwall in the cascade apparently influences the endwall secondary flow,and the optimal locations and strength of actuation are critical for the control of endwall secondary flow in a compressor cascade with the plasma actuators.

  14. Inactivation of soybean trypsin inhibitor by dielectric-barrier discharge (DBD) plasma.

    Science.gov (United States)

    Li, Junguang; Xiang, Qisen; Liu, Xiufang; Ding, Tian; Zhang, Xiangsheng; Zhai, Yafei; Bai, Yanhong

    2017-10-01

    Soybean trypsin inhibitor (STI) is considered as one of the most important anti-nutritional factors in soybeans. The objective of this study was to investigate the impacts and underling mechanisms of dielectric-barrier discharge (DBD) plasma on STI activities. The results shown that DBD plasma treatment significantly induced the inactivation of STI in soymilk and Kunitz-type trypsin inhibitor from soybean (SKTI) in a model system. After exposure to DBD plasma at 51.4W for 21min, the STI activities of soymilk were reduced by 86.1%. Affter being treated by DBD plasma, the intrinsic fluorescence and surface hydrophobicity of SKTI were significantly decreased, while the sulfhydryl contents were increased. It is assumed that DBD plasma-induced conformational changes and oxidative modification might contribute to the inactivation of SKTI. In summary, DBD plasma technology is a potential alternative to heat treatment for the inactivation of anti-nutritional substances in food legumes. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Surface-dependent inactivation of model microorganisms with shielded sliding plasma discharges and applied air flow.

    Science.gov (United States)

    Edelblute, Chelsea M; Malik, Muhammad A; Heller, Loree C

    2015-06-01

    Cold atmospheric plasma inactivates bacteria through reactive species produced from the applied gas. The use of cold plasma clinically has gained recent interest, as the need for alternative or supplementary strategies are necessary for preventing multi-drug resistant infections. The purpose of this study was to evaluate the antibacterial efficacy of a novel shielded sliding discharge based cold plasma reactor operated by nanosecond voltage pulses in atmospheric air on both biotic and inanimate surfaces. Bacterial inactivation was determined by direct quantification of colony forming units. The plasma activated air (afterglow) was bactericidal against Escherichia coli and Staphylococcus epidermidis seeded on culture media, laminate, and linoleum vinyl. In general, E. coli was more susceptible to plasma exposure. A bacterial reduction was observed with the application of air alone on a laminate surface. Whole-cell real-time PCR revealed a decrease in the presence of E. coli genomic DNA on exposed samples. These findings suggest that plasma-induced bacterial inactivation is surface-dependent.

  16. Development of a non-equilibrium 60 MHz plasma jet with a long discharge plume

    Science.gov (United States)

    Uchida, Giichiro; Kawabata, Kazufumi; Ito, Taiki; Takenaka, Kosuke; Setsuhara, Yuichi

    2017-07-01

    High-frequency plasma jets driven by voltages in the frequency range of 6-60 MHz are developed. A long plasma jet, 40 mm in length, is successfully produced by using a pair of ring electrodes outside a quartz tube. The electrode pair consists of a wide power electrode and a narrow ground electrode that is positioned at the head of the tube. The ratio of the length of the ground electrode to the length of the power electrode must be small in order to produce long plasma jets. The high-frequency plasma jet is operated in a non-thermal-equilibrium state at a gas temperature of around 60 °C. Operation at the very-high-frequency of 60 MHz leads to a lower discharge voltage and lower electron energy compared to lower frequencies of 6 and 13.56 MHz. The ability of the very-high-frequency (60 MHz) plasma jet to produce reactive oxygen and nitrogen species in water is also investigated. High H2O2 and NO3- concentrations of more than 1 mmol/l are realized by irradiating 3 ml of deionized water with the plasma for a short period of 2 min.

  17. Product surface hardening in non-self-sustained glow discharge plasma before synthesis of superhard coatings

    Science.gov (United States)

    Krasnov, P. S.; Metel, A. S.; Nay, H. A.

    2017-05-01

    Before the synthesis of superhard coating, the product surface is hardened by means of plasma nitriding, which prevents the surface deformations and the coating brittle rupture. The product heating by ions accelerated from plasma by applied to the product bias voltage leads to overheating and blunting of the product sharp edges. To prevent the blunting, it is proposed to heat the products with a broad beam of fast nitrogen molecules. The beam injection into a working vacuum chamber results in filling of the chamber with quite homogeneous plasma suitable for nitriding. Immersion in the plasma of the electrode and heightening of its potential up to 50-100 V initiate a non-self-sustained glow discharge between the electrode and the chamber. It enhances the plasma density by an order of magnitude and reduces its spatial nonuniformity down to 5-10%. When a cutting tool is isolated from the chamber, it is bombarded by plasma ions with an energy corresponding to its floating potential, which is lower than the sputtering threshold. Hence, the sharp edges are sputtered only by fast nitrogen molecules with the same rate as other parts of the tool surface. This leads to sharpening of the cutting tools instead of blunting.

  18. Hydrogen Plasma Processing of Iron Ore

    Science.gov (United States)

    Sabat, Kali Charan; Murphy, Anthony B.

    2017-06-01

    Iron is currently produced by carbothermic reduction of oxide ores. This is a multiple-stage process that requires large-scale equipment and high capital investment, and produces large amounts of CO2. An alternative to carbothermic reduction is reduction using a hydrogen plasma, which comprises vibrationally excited molecular, atomic, and ionic states of hydrogen, all of which can reduce iron oxides, even at low temperatures. Besides the thermodynamic and kinetic advantages of a hydrogen plasma, the byproduct of the reaction is water, which does not pose any environmental problems. A review of the theory and practice of iron ore reduction using a hydrogen plasma is presented. The thermodynamic and kinetic aspects are considered, with molecular, atomic and ionic hydrogen considered separately. The importance of vibrationally excited hydrogen molecules in overcoming the activation energy barriers, and in transferring energy to the iron oxide, is emphasized. Both thermal and nonthermal plasmas are considered. The thermophysical properties of hydrogen and argon-hydrogen plasmas are discussed, and their influence on the constriction and flow in the of arc plasmas is considered. The published R&D on hydrogen plasma reduction of iron oxide is reviewed, with both the reduction of molten iron ore and in-flight reduction of iron ore particles being considered. Finally, the technical and economic feasibility of the process are discussed. It is shown that hydrogen plasma processing requires less energy than carbothermic reduction, mainly because pelletization, sintering, and cokemaking are not required. Moreover, the formation of the greenhouse gas CO2 as a byproduct is avoided. In-flight reduction has the potential for a throughput at least equivalent to the blast furnace process. It is concluded that hydrogen plasma reduction of iron ore is a potentially attractive alternative to standard methods.

  19. Hydrogen Plasma Processing of Iron Ore

    Science.gov (United States)

    Sabat, Kali Charan; Murphy, Anthony B.

    2017-03-01

    Iron is currently produced by carbothermic reduction of oxide ores. This is a multiple-stage process that requires large-scale equipment and high capital investment, and produces large amounts of CO2. An alternative to carbothermic reduction is reduction using a hydrogen plasma, which comprises vibrationally excited molecular, atomic, and ionic states of hydrogen, all of which can reduce iron oxides, even at low temperatures. Besides the thermodynamic and kinetic advantages of a hydrogen plasma, the byproduct of the reaction is water, which does not pose any environmental problems. A review of the theory and practice of iron ore reduction using a hydrogen plasma is presented. The thermodynamic and kinetic aspects are considered, with molecular, atomic and ionic hydrogen considered separately. The importance of vibrationally excited hydrogen molecules in overcoming the activation energy barriers, and in transferring energy to the iron oxide, is emphasized. Both thermal and nonthermal plasmas are considered. The thermophysical properties of hydrogen and argon-hydrogen plasmas are discussed, and their influence on the constriction and flow in the of arc plasmas is considered. The published R&D on hydrogen plasma reduction of iron oxide is reviewed, with both the reduction of molten iron ore and in-flight reduction of iron ore particles being considered. Finally, the technical and economic feasibility of the process are discussed. It is shown that hydrogen plasma processing requires less energy than carbothermic reduction, mainly because pelletization, sintering, and cokemaking are not required. Moreover, the formation of the greenhouse gas CO2 as a byproduct is avoided. In-flight reduction has the potential for a throughput at least equivalent to the blast furnace process. It is concluded that hydrogen plasma reduction of iron ore is a potentially attractive alternative to standard methods.

  20. Investigation of Vortex Structures in Gas-Discharge Nonneutral Electron Plasma: III. Pulse Ejection of Electrons at the Formation and Radial Oscillations of Vortex Structure

    CERN Document Server

    Kervalishvili, N A

    2015-01-01

    The results of experimental investigations of electron ejection from gas-discharge nonneutral electron plasma at the formation and radial oscillations of vortex structure have been presented. The electrons are injected from the vortex structure and the adjacent region of electron sheath in the form of pulses the duration and periodicity of which are determined by the processes of evolution and dynamics of this structure. The possible mechanisms of pulse ejection of electrons are considered. The influence of electron ejection on other processes in discharge electron sheath is analyzed.

  1. Plasma decay in the afterglow of a high-voltage nanosecond discharge in air

    Science.gov (United States)

    Aleksandrov, N. L.; Anokhin, E. M.; Kindysheva, S. V.; Kirpichnikov, A. A.; Kosarev, I. N.; Nudnova, M. M.; Starikovskaya, S. M.; Starikovskii, A. Yu.

    2012-02-01

    The decay of air plasma produced by a high-voltage nanosecond discharge at room temperature and gas pressures in the range of 1-10 Torr was studied experimentally and theoretically. The time dependence of the electron density was measured with a microwave interferometer. The initial electron density was about 1012 cm-3. The discharge homogeneity was monitored using optical methods. The dynamics of the charged particle densities in the discharge afterglow was simulated by numerically solving the balance equations for electron and ions and the equation for the electron temperature. It was shown that, under these experimental conditions, plasma electrons are mainly lost due to dissociative and three-body recombination with ions. Agreement between the measured and calculated electron densities was achieved only when the rate constant of the three-body electron-ion recombination was increased by one order of magnitude and the temperature dependence of this rate constant was modified. This indicates that the mechanism for three-body recombination of molecular ions differs from that of the well-studied mechanism of atomic ion recombination.

  2. Plasma decay in the afterglow of a high-voltage nanosecond discharge in air

    Energy Technology Data Exchange (ETDEWEB)

    Aleksandrov, N. L.; Anokhin, E. M.; Kindysheva, S. V.; Kirpichnikov, A. A.; Kosarev, I. N.; Nudnova, M. M. [Moscow Institute of Physics and Technology (Russian Federation); Starikovskaya, S. M. [Ecole Polytechnique, route de Saclay (France); Starikovskii, A. Yu. [Princeton University (United States)

    2012-02-15

    The decay of air plasma produced by a high-voltage nanosecond discharge at room temperature and gas pressures in the range of 1-10 Torr was studied experimentally and theoretically. The time dependence of the electron density was measured with a microwave interferometer. The initial electron density was about 10{sup 12} cm{sup -3}. The discharge homogeneity was monitored using optical methods. The dynamics of the charged particle densities in the discharge afterglow was simulated by numerically solving the balance equations for electron and ions and the equation for the electron temperature. It was shown that, under these experimental conditions, plasma electrons are mainly lost due to dissociative and three-body recombination with ions. Agreement between the measured and calculated electron densities was achieved only when the rate constant of the three-body electron-ion recombination was increased by one order of magnitude and the temperature dependence of this rate constant was modified. This indicates that the mechanism for three-body recombination of molecular ions differs from that of the well-studied mechanism of atomic ion recombination.

  3. Plasma characteristics of argon glow discharge produced by AC power supply operating at low frequencies

    Energy Technology Data Exchange (ETDEWEB)

    Kongpiboolkid, Watcharapon; Mongkolnavin, Rattachat [Department of Physics, Facuty of Science, Chulalongkorn University, Bangkok (Thailand); Plasma Technology and Nuclear Fusion Research Unit, Chulalongkorn University, Bangkok (Thailand)

    2015-04-24

    Non-thermal properties of Argon glow discharge operating with various operating pressures were measured and presented in this work. The Argon plasma is produced by a parallel conducting electrodes coupling with a high voltage AC power supply. The power supply can generate high AC voltage at various frequencies. The frequencies for the operation are in the range of a few kHz. The system is capable of generating electric field between the two metal electrodes discharge system. The characteristics of plasma produced were measured by optical emission spectroscopy (OES) technique where electron temperature (T{sub e}) and electron number density (n{sub e}) can be determined by line intensity ratio method. The value of electron number density was then determined from the Saha-Eggert equation. Our results show that the electron number density of the discharge obtained is of the order of 10{sup −17} − 10{sup −18} m{sup −3} where the electron temperature is between 1.00−2.00 eV for various operating frequencies used which are in good agreement with similar results published earlier.

  4. Degradation of Benzene by Using a Silent-Packed Bed Hybrid Discharge Plasma Reactor

    Science.gov (United States)

    Jiang, Nan; Lu, Na; Li, Jie; Wu, Yan

    2012-02-01

    In this work, a novel gas phase silent-packed bed hybrid discharge plasma reactor has been proposed, and its ability to control a simulative gas stream containing 240 ppm benzene is experimentally investigated. In order to optimize the geometry of the reactor, the benzene conversion rate and energy yield (EY) were compared for various inner electrode diameters and quartz tube shapes and sizes. In addition, benzene removal efficiency in different discharge regions was qualitatively analyzed and the gas parameter (space velocity) was systematically studied. It has been found that silent-packed bed hybrid discharge plasma reactor can effectively decompose benzene. Benzene removal proved to achieve an optimum value of 60% with a characteristic energy density of 255 J/L in this paper with a 6 mm bolt high-voltage electrode and a 13 mm quartz tube. The optimal space velocity was 188.1 h-1, which resulted in moderate energy yield and removal efficiency. Reaction by-products such as hydroquinone, heptanoic acid, 4-nitrocatechol, phenol and 4-phenoxy-phenol were identified by mean of GC-MS. In addition, based on these organic by-products, a benzene destruction pathway was proposed.

  5. A global plasma model for reactive deposition of compound films by modulated pulsed power magnetron sputtering discharges

    Science.gov (United States)

    Zheng, B. C.; Wu, Z. L.; Wu, B.; Li, Y. G.; Lei, M. K.

    2017-05-01

    A spatially averaged, time-dependent global plasma model has been developed to describe the reactive deposition of a TiAlSiN thin film by modulated pulsed power magnetron sputtering (MPPMS) discharges in Ar/N2 mixture gas, based on the particle balance and the energy balance in the ionization region, and considering the formation and erosion of the compound at the target surface. The modeling results show that, with increasing the N2 partial pressure from 0% to 40% at a constant working pressure of 0.3 Pa, the electron temperature during the strongly ionized period increases from 4 to 7 eV and the effective power transfer coefficient, which represents the power fraction that effectively heats the electrons and maintains the discharge, increases from about 4% to 7%; with increasing the working pressure from 0.1 to 0.7 Pa at a constant N2 partial pressure of 25%, the electron temperature decreases from 10 to 4 eV and the effective power transfer coefficient decreases from 8% to 5%. Using the modeled plasma parameters to evaluate the kinetic energy of arriving ions, the ion-to-neutral flux ratio of deposited species, and the substrate heating, the variations of process parameters that increase these values lead to an enhanced adatom mobility at the target surface and an increased input energy to the substrate, corresponding to the experimental observation of surface roughness reduction, the microstructure transition from the columnar structure to the dense featureless structure, and the enhancement of phase separation. At higher N2 partial pressure or lower working pressure, the modeling results demonstrate an increase in electron temperature, which shifts the discharge balance of Ti species from Ti+ to Ti2+ and results in a higher return fraction of Ti species, corresponding to the higher Al/Ti ratio of deposited films at these conditions. The modeling results are well correlated with the experimental observation of the composition variation and the microstructure

  6. Pulsed Plasma Methods in Materials Processing

    Science.gov (United States)

    Rej, D. J.

    1996-05-01

    Plasmas are routinely used to synthesize advanced materials, because of their ability to produce reactant species that enable a wide variety of chemical reactions. For example, in microelectronics manufacturing, plasmas are used to etch, clean, ash photoresist, implant, deposit, polymerize, and metalize. The use of pulsed power may extend the utility of plasma processing. Pulsed devices such as coaxial plasma guns, cathodic arcs, pseudosparks have been employed to synthesize materials ranging from novel steel alloys and high-temperature superconductors to diamond coatings. In this talk, we will highlight plasma immersion ion implantation and deposition, methods that improve conventional steady-state chemical and physical vapor deposition techniques. Pulsed power enables energetic ion bombardment before plasma deposition to promote better film adhesion through the formation of a graded interface. Ion bombardment during deposition reduces residual stress in the deposited film, thereby enabling formation of thick layers. Also, pulsed plasma sources have advantages over steady-state devices in that they conserve electrical power and can produce high-density, fully-dissociated plasmas. As an example, we will review recent experiments on the formation of adherent diamond-like carbon films deposited onto relatively large batches of automotive components.

  7. Wettability and Aging of Polymer Substrates after Atmospheric Dielectrical Barrier Discharge Plasma on Demand Treatment

    NARCIS (Netherlands)

    R.A.F. Verkuijlen; Dr Jan Bernards; R. Aben; ir Martijn van Dongen

    2013-01-01

    Plasma treatment is a commonly used technology to modify the wetting behavior of polymer films in the production process for, e.g., printed electronics. As the effect of the plasma treatment decreases in time, the so-called "aging effect", it is important to gain knowledge on how this effect impacts

  8. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    DEFF Research Database (Denmark)

    Zhu, Jiajian; Gao, Jinlong; Ehn, Andreas

    2015-01-01

    , gives more realistic insight into the convection cooling process. Additionally, with the determination of the 3D slip velocity and the 3D length of the plasma column, we give more accurate estimates for the drag force, the electric field strength, the power per unit length, and the radius...... of the conducting zone of the plasma column. © 2015 AIP Publishing LLC....

  9. Wettability and Aging of Polymer Substrates after Atmospheric Dielectrical Barrier Discharge Plasma on Demand Treatment

    NARCIS (Netherlands)

    Dongen, M.H.A. van; Verkuijlen, R.A.F.; Aben, R.; Bernards, J.P.C.

    2013-01-01

    Plasma treatment is a commonly used technology to modify the wetting behavior of polymer films in the production process for, e.g., printed electronics. As the effect of the plasma treatment decreases in time, the so-called "aging effect", it is important to gain knowledge on how this effect impacts

  10. Polymer Surface Treatment by Atmospheric Pressure Low Temperature Surface Discharge Plasma:Its Characteristics and Comparison with Low Pressure Oxygen Plasma Treatment

    Institute of Scientific and Technical Information of China (English)

    Atsushi KUWABARA; Shin-ichi KURODA; Hitoshi KUBOTA

    2007-01-01

    The polymer treatment with a low-temperature plasma jet generated on the atmospheric pressure surface discharge (SD) plasma is performed.The change of the surface property over time,in comparison with low pressure oxygen (O2) plasma treatment,is examined.As one compares the treatment by atmospheric pressure plasma to that by the low pressure O2 plasma of PS (polystyrene) the treatment effects were almost in complete agreement.However,when the atmospheric pressure plasma was used for PP(polypropylene),it produced remarkable hydrophilic effects.

  11. Optical emission spectroscopy of deuterium and helium plasma jets emitted from plasma focus discharges at the PF-1000U facility

    Science.gov (United States)

    Skladnik-Sadowska, E.; Dan'ko, S. A.; Kwiatkowski, R.; Sadowski, M. J.; Zaloga, D. R.; Paduch, M.; Zielinska, E.; Kharrasov, A. M.; Krauz, V. I.

    2016-12-01

    Optical emission spectroscopy techniques were used to investigate the spectra of dense deuterium-plasma jets generated by high-current pulse discharges within the large PF-1000U facility and to estimate parameters of plasma inside the jets and their surroundings. Time-resolved optical spectra were recorded by means of a Mechelle®900 spectrometer. From an analysis of the deuterium line broadening, it was estimated that the electron concentration at a distance 57 cm from the electrode outlets amounted to (0.4-3.7) × 1017 cm-3 depending on the initial gas distribution and the time interval of the spectrum registration after the instant of the plasma jet generation. From the re-absorption dip in the Dβ profile, it was assessed that the electron concentration in the surrounding gas was equal to about 1.5 × 1015 cm-3. On the basis of the measured ratio of He II 468.6 nm and He I 587.6 nm line intensities, it was estimated that the electron temperature amounted to about 5.3 eV. Also estimated were some dimensionless parameters of the investigated plasma jets.

  12. Plasma characterization studies for materials processing

    Energy Technology Data Exchange (ETDEWEB)

    Pfender, E.; Heberlein, J. [Univ. of Minnesota, Minneapolis, MN (United States)

    1995-12-31

    New applications for plasma processing of materials require a more detailed understanding of the fundamental processes occurring in the processing reactors. We have developed reactors offering specific advantages for materials processing, and we are using modeling and diagnostic techniques for the characterization of these reactors. The emphasis is in part set by the interest shown by industry pursuing specific plasma processing applications. In this paper we report on the modeling of radio frequency plasma reactors for use in materials synthesis, and on the characterization of the high rate diamond deposition process using liquid precursors. In the radio frequency plasma torch model, the influence of specific design changes such as the location of the excitation coil on the enthalpy flow distribution is investigated for oxygen and air as plasma gases. The diamond deposition with liquid precursors has identified the efficient mass transport in form of liquid droplets into the boundary layer as responsible for high growth, and the chemical properties of the liquid for the film morphology.

  13. Study of a contracted glow in low-frequency plasma-jet discharges operating with argon

    Energy Technology Data Exchange (ETDEWEB)

    Minotti, F.; Giuliani, L.; Xaubet, M.; Grondona, D. [Departamento de Física, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Buenos Aires, C1428EHA, Buenos Aires, Argentina and Instituto de Física del Plasma (INFIP), Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET), Universidad de Buenos Aires - UBA, C1428EHA, Buenos Aires (Argentina)

    2015-11-15

    In this work, we present an experimental and theoretical study of a low frequency, atmospheric plasma-jet discharge in argon. The discharge has the characteristics of a contracted glow with a current channel of submillimeter diameter and a relatively high voltage cathode layer. In order to interpret the measurements, we consider the separate modeling of each region of the discharge: main channel and cathode layer, which must then be properly matched together. The main current channel was modeled, extending a previous work, as similar to an arc in which joule heating is balanced by lateral heat conduction, without thermal equilibrium between electrons and heavy species. The cathode layer model, on the other hand, includes the emission of secondary electrons by ion impact and by additional mechanisms, of which we considered emission due to collision of atoms excited at metastable levels, and field-enhanced thermionic emission (Schottky effect). The comparison of model and experiment indicates that the discharge can be effectively sustained in its contracted form by the secondary electrons emitted by collision of excited argon atoms, whereas thermionic emission is by far insufficient to provide the necessary electrons.

  14. Fluid model for a partially packed dielectric barrier discharge plasma reactor

    Science.gov (United States)

    Gadkari, Siddharth; Tu, Xin; Gu, Sai

    2017-09-01

    In this work, a two-dimensional numerical fluid model is developed for a partially packed dielectric barrier discharge (DBD) in pure helium. Influence of packing on the discharge characteristics is studied by comparing the results of DBD with partial packing with those obtained for DBD with no packing. In the axial partial packing configuration studied in this work, the electric field strength was shown to be enhanced at the top surface of the spherical packing material and at the contact points between the packing and the dielectric layer. For each value of applied potential, DBD with partial packing showed an increase in the number of pulses in the current profile in the positive half cycle of the applied voltage, as compared to DBD with no packing. Addition of partial packing to the plasma-alone DBD also led to an increase in the electron and ion number densities at the moment of breakdown. The time averaged electron energy profiles showed that a much higher range of electron energy can be achieved with the use of partial packing as compared to no packing in a DBD, at the same applied power. The spatially and time averaged values over one voltage cycle also showed an increase in power density and electron energy on inclusion of partial packing in the DBD. For the applied voltage parameters studied in this work, the discharge was found to be consistently homogeneous and showed the characteristics of atmospheric pressure glow discharge.

  15. Decontamination effects of low-temperature plasma generated by corona discharge. Part II: new insights.

    Science.gov (United States)

    Scholtz, V; Julák, J; Kríha, V; Mosinger, J; Kopecká, S

    2007-01-01

    The second part of our paper presents the results of experiments with the decontamination of surfaces by low-temperature plasma generated by corona discharge in air at atmospheric pressure. A simple device is described and the effects of the corona discharge on model microorganisms, viz. the yeast Candida albicans, Gram-negative bacteria Escherichia coli, Enterobacter aerogenes, Neisseria sicca, Stenotrophomonas maltophilia, Gram-positive bacteria Deinococcus radiodurans, Enterococcus faecium, Staphylococcus epidermidis, Streptococcus sanguinis, and vegetative and spore forms of Geobacillus stearothermophilus are discussed. A similar microbicidal effect after about one-minute exposure was observed in all vegetative forms of the microorganisms. Measurement in growth inhibition zones on a semisolid medium was used to determine the dependence of the microbicidal effect on exposure time and the distance between electrodes. Counting of colonies served to assess the microbicidal effect of the discharge on contaminated inert surfaces observable after more than 1 min exposure. Geobacillus stearothermophilus spores were found to have several times lower susceptibility to the action of the discharge and the microbicidal effect was observed only after an 8 min exposure. Reaction with the iodide reagent did not unambiguously demonstrate the difference between ozone and singlet oxygen as presumed active components of the corona. The area distribution of reactive oxygen species was determined; it was found to differ from the Wartburg law depending on exposure time. Qualitative evidence was obtained on the penetration of the reactive oxygen species into the semisolid medium.

  16. Cluster processes in gases and plasmas

    CERN Document Server

    Smirnov, Boris M

    2009-01-01

    Boris M. Smirnov received his Ph.D. in physics from Leningrad State University in 1968. After working in different research positions, he finally accepted a post as head of one of the divisions of the Institute for High Temperatures at the Russian Academy of Sciences in Moscow in 1986. Professor Smirnov is the author and co-author of approximately 50 books as well as 400 research articles in plasma physics, atomic physics, and atomic clusters. He is Vice Chairman of the National Council for Low Temperature Plasma and Chairman ofa Section on Elementary Processes in Plasma. Professor Smirnov`s r

  17. Ultrasonic Plasma Spray--A New Plasma Spray Process

    Institute of Scientific and Technical Information of China (English)

    LU Zhi-qing; ZHANG Hua-tang; WEN Xiong-wei; LI Lu-ming

    2004-01-01

    The method of arc- ultrasonic is introduced into plasma spray process. The process of spray ZrO2-NiCoCr AlY thermal barrier coatings (TBCs) using air plasma spray (APS) process is studied. A exciting source which can be adjusted from audio frequency to several hundred thousand Hertz is designed successfully. The ultrasonic exciting source is coupled with conventional DC spraying power supply. A few ultrasonic frequencies are selected in the testing. Several parts of the coatings with the coupling arc- ultrasonic are compared with the coatings without it. The results show: with 50 kHz and 80 kHz ultrasound, the coating qualities are improved, whereas 30 kHz has an opposite effect.

  18. A literature review of organisational, individual and teamwork factors contributing to the ICU discharge process.

    Science.gov (United States)

    Lin, Frances; Chaboyer, Wendy; Wallis, Marianne

    2009-02-01

    It is everyday news that we need more intensive care unit (ICU) beds, thus effective use of existing resources is imperative. The aim of this literature review was to critically analyse current literature on how organizational factors, individual factors and teamwork factors influence the ICU discharge process. A better understanding of discharge practices has the potential to ultimately influence ICU resource availability. Databases including CINAHL, MEDLINE, PROQUEST, SCIENCE DIRECT were searched using key terms such as ICU discharge, discharge process, ICU guidelines and policies, discharge decision-making, ICU organisational factors, ICU and human factors, and ICU patient transfer. Articles' reference lists were also used to locate relevant literature. A total of 21 articles were included in the review. Only a small number of ICUs used written patient discharge guidelines. Consensus, rather than empirical evidence, dictates the importance of guidelines and policies. Premature discharge, discharge after hours and discharge by triage still exist due to resources constraints, even though the literature suggests these are associated with increased mortality. Teamwork and team training appear to be effective in improving efficiency and communication between professions or between clinical areas. However, this aspect has rarely been researched in relation to ICU patient discharge. Intensive care patient discharge is influenced by organisational factors, individual factors and teamwork factors. Organisational interventions are effective in reducing ICU discharge delay and shortening patient hospital stay. More rigorous research is needed to discover how these factors influence the ICU discharge process.

  19. The Process of Plasma Chemical Photoresist Film Ashing from the Surface of Silicon Wafers

    Directory of Open Access Journals (Sweden)

    Siarhei Bordusau

    2013-01-01

    Full Text Available At present, the research for finding new technical methods of treating materials with plasma, including the development of energy and resource saving technologies for microelectronic manufacturing, is particularly actual.In order to improve the efficiency of microwave plasma chemical ashing of photoresist films from the surface of silicon wafers a two-stage process of treating was developed. The idea of the developed process is that wafers coated with photoresist are pre-heated by microwave energy. This occurs because the microwave energy initially is not spent on the excitation and maintenance of a microwave discharge but it is absorbed by silicon wafers which have a high tangent of dielectric losses. During the next step after the excitation of the microwave discharge the interaction of oxygen plasma with a pre-heated photoresist films proceeds more intensively. The delay of the start of plasma forming process in the vacuum chamber of a plasmatron with respect to the beginning of microwave energy generation by a magnetron leads to the increase of the total rate of photoresist ashing from the surface of silicon wafers approximately 1.7 times. The advantage of this method of microwave plasma chemical processing of semi-conductor wafers is the possibility of intensifying the process without changing the design of microwave discharge module and without increasing the input microwave power supplied into the discharge.

  20. Plasma processing of superconducting radio frequency cavities

    Science.gov (United States)

    Upadhyay, Janardan

    The development of plasma processing technology of superconducting radio frequency (SRF) cavities not only provides a chemical free and less expensive processing method, but also opens up the possibility for controlled modification of the inner surfaces of the cavity for better superconducting properties. The research was focused on the transition of plasma etching from two dimensional flat surfaces to inner surfaces of three dimensional (3D) structures. The results could be applicable to a variety of inner surfaces of 3D structures other than SRF cavities. Understanding the Ar/Cl2 plasma etching mechanism is crucial for achieving the desired modification of Nb SRF cavities. In the process of developing plasma etching technology, an apparatus was built and a method was developed to plasma etch a single cell Pill Box cavity. The plasma characterization was done with the help of optical emission spectroscopy. The Nb etch rate at various points of this cavity was measured before processing the SRF cavity. Cylindrical ring-type samples of Nb placed on the inner surface of the outer wall were used to measure the dependence of the process parameters on plasma etching. The measured etch rate dependence on the pressure, rf power, dc bias, temperature, Cl2 concentration and diameter of the inner electrode was determined. The etch rate mechanism was studied by varying the temperature of the outer wall, the dc bias on the inner electrode and gas conditions. In a coaxial plasma reactor, uniform plasma etching along the cylindrical structure is a challenging