Microsecond plasma opening switch experiments on GIT-4

International Nuclear Information System (INIS)

Bystritskij, V.M.; Lisitsyn, I.V.; Sinebryukhov, A.A.; Sinebryukhov, V.A.; Kim, A.A.; Kokshenev, V.A.; Koval'chuk, B.M.

1996-01-01

The plasma opening switch (POS) operation at the current level up to 2 MA was studied at the terawatt power GIT-4 generator. The experiments are described in which the electrode diameter and the strength of the applied magnetic field were varied, and different plasma sources were used. It is shown that the high voltage / low impedance switch operation can be achieved if the linear current density at the POS cathode does not exceed 20 kA/cm. This value limits the maximum cathode diameter of the magnetically insulated transmission line. The anode diameter is limited by the requirement of no gap closure with a dense electrode plasma. The application of external magnetic field decreases the plasma density necessary for achieving a long POS conduction time operation regime. (J.U.). 1 tab., 4 refs

High explosive driven plasma opening switches

International Nuclear Information System (INIS)

Greene, A.E.; Bowers, R.L.; Brownell, J.H.; Goforth, J.H.; Oliphant, T.A.; Weiss, D.L.

1983-01-01

A joint theoretical and experimental effort is underway to understand and improve upon the performance of high explosive driven plasma opening switches such as those first described by Pavlovskii et al. We have modeled these switches in both planar and cylindrical geometry using a one dimensional Lagrangian MHD code. This one-dimensional analysis is now essentially complete. It has shown that simple, one-dimensional, compression of the current-carrying channel can explain the observed resistance increases during the time of flight of the HE detonation products. Our calculations imply that ionization plays an important role as an energy sink and the performance of these switches might be improved by a judicious choice of gases. We also predict improved performance by lowering the pressure in the plasma channel. The bulk of our experimental effort to date has been with planar switches. We have worked with current densities of 0.25 to 0.4 MA/cm and have observed resistance increases of 40 to 60 mΩ. Significant resistance increases are observed later than the time of flight of the HE detonation products. We suggest that these resistance increases are due to mixing between the hot plasma and the relatively cooler detonation products. Such mixing is not included in the 1-D, Lagrangian code. We are presently beginning a computational effort with a 2-D Eulerian code. The status of this effort is discussed. Experimentally we have designed an apparatus that will permit us to test the role of different gases and pressures. This system is also in a planar geometry, but the plasma channel is doughnut shaped, permitting us to avoid edge effects associated with the planar rectangular geometry. The first experiments with this design are quite encouraging and the status of this effort is also discussed

Long conduction time plasma opening switch experiments at Sandia National Laboratories

International Nuclear Information System (INIS)

Savage, M.E.; Simpson, W.W.; Cooper, G.W.; Usher, M.A.

1993-01-01

Sandia National Laboratories has undertaken an ambitious program to reduce the size and cost of large pulsed power drivers. The program basis is inductive energy storage and Plasma Opening Switches (POS). Inductive energy storage has well known advantages, including increased efficiency and reduced stress on the vacuum interface. The Sandia approach is to retain the reliable and efficient Marx generator and the temporal pulse compression of the water dielectric capacitor. A triggered closing switch, developed at Sandia, transfers the capacitor charge into the energy storage inductor. This approach has several advantages, including relaxed requirements on Marx jitter and inductance, and much faster current risetime in the energy storage inductor. The POS itself is the key to the Sandia program. The switch design uses an auxiliary magnetic field to inject the plasma and hold it in place during conduction. After opening begins, the self magnetic field of the power pulse pushes on the plasma to increase the opened gap. The authors use magnetic pressure because they desire POS gaps of several cm. Typical plasma opening switches do not achieve large gaps. Improved opening allows more efficient transfer to loads. They present results from recent experiments at Sandia. Their driver presently supplies 650 kA with a 240 ns risetime to the input of the POS. The storage inductor is a 17 Ohm magnetically insulated transmission line (MITL) that is five meters long. They discuss the ways in which magnetic field influences the POS, and the ways in which they control the magnetic fields

Experiments on microsecond conduction time plasma opening switch mechanisms

International Nuclear Information System (INIS)

Rix, W.; Coleman, M.; Miller, A.R.; Parks, D.; Robertson, K.; Thompson, J.; Waisman, E.; Wilson, A.

1993-01-01

The authors describe a series of experiments carried out on ACE 2 and ACE 4 to elucidate the mechanisms controlling the conduction and opening phases on plasma opening switches in a radial geometry with conduction times on the order of a microsecond. The results indicate both conduction and opening physics are similar to that observed on lower current systems in a coaxial geometry

A novel carbon gun for use with plasma opening switches

International Nuclear Information System (INIS)

Stevenson, P.; Gregory, K.; Cliffe, R.J.; Smith, I.R.

2001-01-01

The carbon gun is probably the most common plasma source used in plasma opening switches. Nevertheless, it either produces a contaminated plasma, as the flashover surface erodes, or requires regular treatment with graphite paint. The novel form of the plasma gun described in this paper overcomes the disadvantages of existing designs and produces a cleaner plasma. Experimental results illustrate the performance of a prototype system. (author)

Performance of magnetically-injected-plasma opening switches on the particle beam fusion accelerator 2

International Nuclear Information System (INIS)

Rochau, G.E.; McDaniel, D.H.; Mendel, C.W.; Sweeney, M.A.; Moore, W.B.S.; Mowrer, G.R.; Zagar, D.M.

1990-01-01

Plasma opening switch (POS) experiments have been performed on the PBFA II ion beam accelerator to develop a switch which will provide voltage and power gain to an applied-B lithium ion diode. These experiments have successfully coupled power to electron and ion beam diodes using a Magnetically-Injected-Plasma (MIP) POS. Carbon plasma with electron densities of 1 x 10 12 to 2 x 10 13 /cm 3 have been injected from the anode into the 8 cm gap of the 20-ohm Magnetically-Insulated-Transmission Line (MITL) of PBFA II along a B r,z magnetic field. The MIP switch uses the inertia of the plasma to keep the switch closed and the magnetic pressure of B θ from the conduction current to open the switch. The configuration of the injecting magnetic field and the plasma source has a significant effect on the efficiency of coupling power to high impedance loads. Plasma near the center of the injecting magnetic field limits the opening impedance of the switch and subsequently the power delivered to the load. The axial location of the switch with respect to the load has also been identified as a critical parameter in increasing the coupling efficiency. A length of 10 to 20 cm of MITL between the POS and the load has increased the power delivered to the load. Data on switch performance with high impedance loads and factors which improved performance are discussed

GIT 16: megajoule pulsed generator with plasma opening switch for Z-pinch loads

International Nuclear Information System (INIS)

Bugaev, S.P.; Volkov, A.M.; Kim, A.A.

1997-01-01

Megajoule complex GIT 16 reserved for perfecting technology of forming powerful impulse with the help of intermediate inductive storage and break contact in the form of plasma opening switches and for investigating of irradiating loading of Z-pinch type is presented. The characteristics of isolated complex elements are given and basic results characterizing microsecond plasma opening switches at the current level of same M A are described

Electron and ion magnetohydrodynamic effects in plasma opening switches

International Nuclear Information System (INIS)

Grossmann, J.M.; DeVore, C.R.; Ottinger, P.F.

1993-01-01

Preliminary results are presented of a numerical code designed to investigate electron and ion magnetohydrodynamic effects in plasma erosion opening switches. The present model is one-dimensional and resolves effects such as the JxB deformation of the plasma, and the penetration of magnetic field either by anomalous resistivity or electron magnetohydrodynamics (Hall effect). Comparisons with exact analytic results and experiment are made

A self-similar model for conduction in the plasma erosion opening switch

International Nuclear Information System (INIS)

Mosher, D.; Grossmann, J.M.; Ottinger, P.F.; Colombant, D.G.

1987-01-01

The conduction phase of the plasma erosion opening switch (PEOS) is characterized by combining a 1-D fluid model for plasma hydrodynamics, Maxwell's equations, and a 2-D electron-orbit analysis. A self-similar approximation for the plasma and field variables permits analytic expressions for their space and time variations to be derived. It is shown that a combination of axial MHD compression and magnetic insulation of high-energy electrons emitted from the switch cathode can control the character of switch conduction. The analysis highlights the need to include additional phenomena for accurate fluid modeling of PEOS conduction

Plasma opening switch for long-pulse intense ion beam

International Nuclear Information System (INIS)

Davis, H.A.; Mason, R.J.; Bartsch, R.R.; Greenly, J.B.; Rej, D.J.

1992-01-01

A Plasma Opening Switch (POS) is being developed at Los Alamos, as part of an intense ion beam experiment with special application to materials processing. The switch must conduct up to 100 kA for 600 ns, and open quickly to avoid premature gap closure in the ion beam diode load. Power multiplication is not a necessity, but prepulse suppression is. A positive central polarity is desirable, since with it an ion beam can be conveniently launched beyond the switch from the central anode toward a negatively charged target. Thus, otherwise by virtue of traditional scaling rules, a POS was designed with a 1.25 cm radius inner anode, and a 4.75 cm radius outer cathode. This has been constructed, and subjected to circuit, and simulational analysis. The computations are being performed with the 2D ANTHEM implicit code. Preliminary results show a marked difference in switching dynamics, when the central positive polarity is used in place of the more conventional opposite choice. Opening goes by the fast development of a central anode magnetic layer, rather than by the more conventional slow evolution of a cathode gap. With the central anode, higher fill densities are needed to achieve desired conduction times. This has suggested switch design improvements, which are discussed

Plasma opening switch for long-pulse intense ion beam

International Nuclear Information System (INIS)

Davis, H.A.; Mason, R.J.; Bartsch, R.R.; Greenly, J.B.; Rej, D.J.

1993-01-01

A Plasma Opening Switch (POS) is being developed at Los Alamos, as part of an intense ion beam experiment with special application to materials processing. The switch must conduct up to 100 kA for 400 ns, and open quicky to avoid premature gap closure in the ion beam diode load. Power multiplication is not a necessity, but prepulse suppression is. A positive central polarity is desirable, since with it an ion beam can be conveniently launched beyond the switch from the central anode toward a negatively charged target. Using traditional scaling rules, a POS was designed with a 1.25 cm radius inner anode, and a 5.0 cm radius outer cathode. This has been constructed, and subjected to circuit, and simulational analysis. The computations are being performed with the 2D ANTHEM implicit code. Preliminary results show a marked difference in switching dynamics, when the central positive polarity is used in place of the more conventional opposite choice. Opening is achieved by the fast development of a central anode magnetic layer, rather than by the more conventional slow evolution of a cathode gap. With the central anode, higher fill densities are needed to achieve desired conduction times. This has suggested switch design improvements, which are discussed

Time resolved plasma characterization in a long conduction time planar plasma opening switch

International Nuclear Information System (INIS)

Adler, L.K.; Greenly, J.B.; Qi, N.; Hammer, D.A.

1989-01-01

The authors discuss additional experiments in which the plasma dynamics and properties will be monitored in detail before and during opening. Space and time resolved density, temperature and motion information about the plasma and neutrals is given by emission spectroscopy and streak photography and correlated to the current and voltage traces. Specifically, we will look for the effects of neutrals evolving off of surfaces, stagnation of the switch plasma, and rvec J x rvec B motion of the plasma downstream of the switch. Diagnostics include current and voltage monitors, a multi-aperture biased Faraday cup, emission spectroscopy and streak photography. Pairs of B dot loops are positioned in the stripline just upstream and downstream of the POS. Also, two single B loops were placed further downstream to look for bulk plasma motion. An inductive monitor gives the voltage at the upstream side of the POS and the Faraday cup monitors the gun plasma consistency from shot to shot

Observation of plasma motion in a coaxial plasma opening switch with a chordal laser interferometer

International Nuclear Information System (INIS)

Teramoto, Y.; Urakami, H.; Akiyama, H.; Kohno, S.; Katsuki, S.

2002-01-01

Electron densities in a coaxial plasma opening switch were measured at many lines-of-slight. In the present experiment, electron density was measured by a He-Ne laser interferometer with chordal lines-of sight. In order to observe the motion of the POS plasma, the electron density contours during the conduction, opening and post-opening phases were drawn by combining the results of interferometer experiments. The radial and axial motion of POS plasma was investigated from the density contours. As conduction time progressed, the POS plasma moved toward downstream. At 800 ns, which corresponds to the time of opening in the current waveform, low-density region less than 10 15 cm -2 is seen at 10 mm from the cathode. After the opening was completed, the low-density gap disappeared and the shape of the corn-shape-like plasma was distorted. (author)

Plasma erosion opening switch in the double-pulse operation mode of a high-current electron accelerator

International Nuclear Information System (INIS)

Isakov, I.F.; Lopatin, V.S.; Remnev, G.E.

1987-01-01

This paper reports the results of investigations of the operation of a fast current opening switch, with a 10/sup 13/-10/sup 16/ plasma density produced either by dielectric surface flashover or by explosive emission of graphite. A series of two pulses was applied to two diodes in parallel. The first pulse produced plasma in the first diode which closed that diode gap by the arrival time of the second pulse. The first, shorted, diode then acted as an erosion switch for the second pulse. A factor of 2.5-3 power multiplication was obtained under optimum conditions. The opening-switch resistance during the magnetic insulation phase, neglecting the electron losses between the switch and the generating diode, exceeded 100 Ω. The duration of the rapid opening phase was less than 5 ns under optimum conditions. This method of plasma production does not require external plasma sources, and permits a wide variation of plasma density, which in turn allows high inductor currents and stored energies

Observation of plasma motion in a coaxial plasma opening switch with a chordal laser interferometer

Energy Technology Data Exchange (ETDEWEB)

Teramoto, Y.; Urakami, H.; Akiyama, H. [Kumamoto Univ., Graduate School of Science and Technology, Kumamoto (Japan); Kohno, S. [Ariake National College of Technology, Dept. of Electrical Engineering, Fukuoka (Japan); Katsuki, S. [Kumamoto Univ., Dept. of Electrical and Computer Engineering, Kumamoto (Japan)

2002-06-01

Electron densities in a coaxial plasma opening switch were measured at many lines-of-slight. In the present experiment, electron density was measured by a He-Ne laser interferometer with chordal lines-of sight. In order to observe the motion of the POS plasma, the electron density contours during the conduction, opening and post-opening phases were drawn by combining the results of interferometer experiments. The radial and axial motion of POS plasma was investigated from the density contours. As conduction time progressed, the POS plasma moved toward downstream. At 800 ns, which corresponds to the time of opening in the current waveform, low-density region less than 10{sup 15} cm{sup -2} is seen at 10 mm from the cathode. After the opening was completed, the low-density gap disappeared and the shape of the corn-shape-like plasma was distorted. (author)

Plasma opening switch studies of the applied Bz diode on the LION accelerator

International Nuclear Information System (INIS)

Struckman, C.K.; Kusse, B.R.; Meyerhofer, D.D.; Rondeau, G.

1988-01-01

The LION accelerator, 1.5 MV, 4Ω, at Cornell University is being used to study the characteristics of an applied B z , or, barrel diode. A plasma opening switch (POS) has been used to shape the voltage pulse seen by the diode. The results of a series of experiments utilizing a POS are presented. The plasma switch geometry is unique, with the plasma source located inside the center conductor of a coaxial transmission line. The switch region is located between the 17 cm radius anode and the 23 cm radius cathode. The switch is constructed of a flashboard plasma source bent into an azimuthally symmetric ring. The axial length of the plasma is only about 2 cm; which is much smaller than the switch radius. The plasma diffuses into the anode-cathode space through axially oriented slots in the anode. The plasma in the switch region has been characterized during static testing (no generator pulse) using Faraday cups. By using time of flight calculations, the Faraday cups give rough estimates of both the plasma density and velocity. Since the generator pulse is so short (100 ns) these static characterizations are indicative of the plasma when the voltage pulse is present. This low density, fast plasma produced the best results for the diode voltage pulse. Results from recently constructed Langmuir probes are also presented

High voltage, high power operation of the plasma erosion opening switch

International Nuclear Information System (INIS)

Neri, J.M.; Boller, J.R.; Ottinger, P.F.; Weber, B.V.; Young, F.C.

1987-01-01

A Plasma Erosion Opening Switch (PEOS) is used as the opening switch for a vacuum inductive storage system driven by a 1.8-MV, 1.6-TW pulsed power generator. A 135-nH vacuum inductor is current charged to ∼750 kA in 50 ns through the closed PEOS which then opens in <10 ns into an inverse ion diode load. Electrical diagnostics and nuclear activations from ions accelerated in the diode yield a peak load voltage (4.25 MV) and peak load power (2.8 TW) that are 2.4 and 1.8 times greater than ideal matched load values for the same generator pulse

Fast-opening vacuum switches for high-power inductive energy storage

International Nuclear Information System (INIS)

Cooperstein, G.

1988-01-01

The subject of fast-opening vacuum switches for high-power inductive energy storage is emerging as an exciting new area of plasma science research. This opening switch technology, which generally involves the use of plasmas as the switching medium, is key to the development of inductive energy storage techniques for pulsed power which have a number of advantages over conventional capacitive techniques with regard to cost and size. This paper reviews the state of the art in this area with emphasis on applications to inductive storage pulsed power generators. Discussion focuses on fast-opening vacuum switches capable of operating at high power (≥10 12 W). These include plasma erosion opening switches, ion beam opening switches, plasma filled diodes, reflex diodes, plasma flow switches, and other novel vacuum opening switches

Energetic ion emission in a positive polarity nanosecond plasma opening switch

Energy Technology Data Exchange (ETDEWEB)

Sarfaty, M [Univ. of Wisconsin, Madison, WI (United States); Krasik, Ya E; Weingarten, A; Fruchtman, A; Maron, Y [Weizmann Institute of Science, Rehovot (Israel). Department of Physics

1997-12-31

The emission was studied of energetic ions from the plasma in a coaxial Plasma Opening Switch (POS) powered by a 300 kV, 15 kA, 90 ns positive polarity pulse. Fluxes lasting 2 - 3 ns of ions flowing radially onto the cathode were observed at all axial locations of the switch plasma within 5 ns of the beginning of the upstream POS current. It is suggested that the termination of this ion flux is due to the formation of a cathode plasma, which is consistent with our spectroscopic measurements. Later in the pulse, longer duration (100 ns) ion fluxes were observed radially, first appearing in the generator side of the switch plasma. Fluxes 30 - 40 ns long of ions flowing axially towards the POS load at velocities (2{+-}1) x 10{sup 8} cm/s were also observed. The dependences of the start time of the axial ion flow, of the ion velocities, and of the ion flux on the POS operation parameters were studied. (author). 6 figs., 5 refs.

Energetic ion emission in a positive polarity nanosecond plasma opening switch

International Nuclear Information System (INIS)

Sarfaty, M.; Krasik, Ya.E.; Weingarten, A.; Fruchtman, A.; Maron, Y.

1996-01-01

The emission was studied of energetic ions from the plasma in a coaxial Plasma Opening Switch (POS) powered by a 300 kV, 15 kA, 90 ns positive polarity pulse. Fluxes lasting 2 - 3 ns of ions flowing radially onto the cathode were observed at all axial locations of the switch plasma within 5 ns of the beginning of the upstream POS current. It is suggested that the termination of this ion flux is due to the formation of a cathode plasma, which is consistent with our spectroscopic measurements. Later in the pulse, longer duration (100 ns) ion fluxes were observed radially, first appearing in the generator side of the switch plasma. Fluxes 30 - 40 ns long of ions flowing axially towards the POS load at velocities (2±1) x 10 8 cm/s were also observed. The dependences of the start time of the axial ion flow, of the ion velocities, and of the ion flux on the POS operation parameters were studied. (author). 6 figs., 5 refs

Anomalous resistivity in the plasma opening switch

Energy Technology Data Exchange (ETDEWEB)

Dolgachev, G I; Zakatov, L P; Kalinin, Yu G; Kingsep, A S; Nitishinskij, M S; Ushakov, A G [Kurchatov Institute, Moscow (Russian Federation). Applied Physics Division

1997-12-31

Experimental studies and modelling together with analytical considerations of anomalous resistivity in the plasma opening switch (POS) are being pursued to improve the understanding of the physical mechanism of the POS conduction phase. Experiments have been undertaken for a `microsecond` POS of coaxial geometry. Measurements of Stark broadening of the H{sub {alpha}} line allowed turbulent oscillations in plasma to be found at the conductivity stage. A comparison with the modelling including low-frequency (ion-acoustic) turbulence and Doppler broadening (neutral gas temperature 1-3 eV) the electric field value to be estimated to 10-30 kV/cm. The turbulent field increased toward the cathode up to 50 kV/cm in the near-cathode layer. (author). 3 figs., 14 refs.

Application of plasma erosion opening switches to high power accelerators for pulse compression and power multiplication

International Nuclear Information System (INIS)

Meyer, R.A.; Boller, J.R.; Commisso, R.J.

1983-01-01

A new vacuum opening switch called a plasma erosion opening switch is described. A model of its operation is presented and the energy efficiency of such a switch is discussed. Recent high power experiments on the Gamble II accelerator are described and compared to previous experiments

Two-dimensional single fluid MHD simulations of plasma opening switches

International Nuclear Information System (INIS)

Roderick, N.F.; Payne, S.S.; Peterkin, R.E. Jr.; Frese, M.H.; Hussey, T.W.

1989-01-01

Simulations of plasma opening switch have been made using two-dimensional, single fluid, magnetohydrodynamic codes HAM and MACH2. A variety of mechanisms for magnetic field penetration have been investigated. These include plasma convection, classical and microturbulent resistive diffusion, and Hall effect transport. We find that plasma microturbulent models are necessary to explain the broad current channels observed in experiments. Both heuristic and consistent microturbulent models are able to explain observed channel widths and penetration features. The best results are obtained for a consistent model that includes the Buneman, ion acoustic, and lower hybrid microturbulent collision frequencies and threshold conditions. Maximum microturbulent collision frequencies of 5 ω p , are typical. Field transport and current channel profiles are in excellent agreement with experimental observations for GAMBLE I, GAMBLE II, and SUPERMITE experiments. Dominant field penetration mechanisms and center of mass plasma motion are current and density dependent. Including the Hall effect enhanced field penetration. Center of mass motion is negligible for the GAMBLE I experiments but significant for the GAMBLE II conditions. Scaling of plasma opening time with switch length and density can be fit by linear representations for lengths from 0.03 m to 0.24 m and ion densities from 10 18 m -3 to 1.5 times 10 19 m -3 . 15 refs., 7 figs., 1 tab

Experimental investigation of the ion current distribution in microsecond plasma opening switch

Energy Technology Data Exchange (ETDEWEB)

Bystritskij, V; Grigor` ev, S; Kharlov, A; Sinebryukhov, A [Russian Academy of Sciences, Tomsk (Russian Federation). Institute of Electrophysics

1997-12-31

This paper is devoted to the investigations of properties of the microsecond plasma opening switch (MPOS) as an ion beam source for surface modification. Two plasma sources were investigated: flash-board and cable guns. The detailed measurements of axial and azimuthal distributions of ion current density in the switch were performed. It was found that the azimuthal inhomogeneity of the ion beam increases from the beginning to the end of MPOS. The advantages and problems of this approach are discussed. (author). 5 figs., 2 refs.

Two dimensional Hall MHD modeling of a plasma opening switch with density inhomogeneities

Energy Technology Data Exchange (ETDEWEB)

Zabaidullin, O [Kurchatov Institute, Moscow (Russian Federation); Chuvatin, A; Etlicher, B [Ecole Polytechnique, Palaiseau (France). Laboratoire de Physique des Milieux Ionises

1997-12-31

The results of two-dimensional numerical modeling of the Plasma Opening Switch in the MHD framework with Hall effect are presented. An enhanced Hall diffusion coefficient was used in the simulations. Recent experiments justify the application of this approach. The result of the modeling also correlates better with the experiment than in the case of the classical diffusion coefficient. Numerically generated pictures propose a switching scenario in which the translation between the conduction and opening phases can be explained by an abrupt `switching on` and further domination of the Hall effect at the end of the conduction phase. (author). 3 figs., 6 refs.

Plasma opening switch development for the Particle Beam Fusion Accelerator II (PBFA II)

International Nuclear Information System (INIS)

Stinnett, R.W.; McDaniel, D.H.; Rochau, G.E.

1987-01-01

The authors conducted plasma opening switch (POS) experiments on Sandia National Laboratories' new Particle Beam Fusin Accelerator II (PBFA II) (12 MV, 100 TW, 50 ns), on the Supermite accelerator (2 MV, 2 TW, 50 ns) and on the Naval Research Laboratory's Gamble II accelerator (1.8 MV, 1.6 TW, 70 ns). The POS systems on the PBFA II and Supermite accelerators use a newly developed flashboard plasma source to provide the plasma necessary to conduct the large (> 1 MA) currents produced byu these accelerators. In the Supermite experiments, the plasma opening switch conducted currents up to 1 MA before opening in less than 10 ns into an electron beam load. These experiments achieved significant voltage gain relative to the voltage across a matched load. In experiments on Gamble II, power gains of up to 1.7 were achieved using a POS in a strongly coaxial geometry (r/sub outer//r/sub inner/ = 2) with a large magnetic field at the cathode. The POS system on PBFA II is unique because of its size and voltage. This POS system is designed to conduct over 6 MA before opening. In present experiments it has conducted currents of 4-5 MA for over 50 ns

Plasma density evolution in plasma opening switch obtained by a time-resolved sensitive He-Ne interferometer

Science.gov (United States)

Chen, Lin; Ren, Jing; Guo, Fan; Zhou, LiangJi; Li, Ye; He, An; Jiang, Wei

2014-03-01

To understand the formation process of vacuum gap in coaxial microsecond conduction time plasma opening switch (POS), we have made measurements of the line-integrated plasma density during switch operation using a time-resolved sensitive He-Ne interferometer. The conduction current and conduction time in experiments are about 120 kA and 1 μs, respectively. As a result, more than 85% of conduction current has been transferred to an inductive load with rise time of 130 ns. The radial dependence of the density is measured by changing the radial location of the line-of-sight for shots with the same nominal POS parameters. During the conduction phase, the line-integrated plasma density in POS increases at all radial locations over the gun-only case by further ionization of material injected from the guns. The current conduction is observed to cause a radial redistribution of the switch plasma. A vacuum gap forms rapidly in the plasma at 5.5 mm from the center conductor, which is consistent with the location where magnetic pressure is the largest, allowing current to be transferred from the POS to the load.

Measurement of performance parameters of plasma source for plasma opening switch on Qiangguang-Ⅰ generator

International Nuclear Information System (INIS)

Luo Weixi; Zeng Zhengzhong; Lei Tianshi; Wang Liangping; Hu Yixiang; Sun Tieping; Huang Tao

2012-01-01

The plasma source (cable guns) of the plasma opening switch (POS) on Qiangguang Ⅰ generator was chosen as the study object. The plasma source performance was investigated by using charge collectors. Experimental results show that the plasma ejection density is positively correlated with the structural parameter, the distance between gun core tip and muzzle plane, and the plasma ejection velocity is negatively correlated with the parameter. The increasing rate of plasma ejection density is less than that of drive current. As far as a plasma source with tens of cable plasma guns is concerned, the influence of single cable gun's discharge dispersancy on plasma uniformity is little. Analysis of uncertainty shows that the uncertainty of measurement can be reduced by increasing the number of experiments and averaging the results. The combined standard uncertainty of plasma ejection density is less than 10%. (authors)

Preliminary studies of the plasma focus as an opening switch

International Nuclear Information System (INIS)

Venneri, F.; Gerdin, G.

1983-01-01

Sharp current interruption at pinch time suggests the possible application of the plasma focus as an opening switch. Switch impedances on the order of 0.5 ohms or greater would be of interest to pulsed power applications if the rise time for the impedance is sufficiently short. The experimental determination of the magnitude of the plasma focus impedance at pinch time and its nature (R or L) are obviously important in assessing the feasibility of this application. An experimental estimate of the Spitzer resistance of the plasma focus based on soft-X-ray measurements indicates a Spitzer resistance of 9 mΩ. Estimates of resistance based on the maximum particle energy observed 4 (V about E /sub MAX/ /e) and the current at pinch time (R about E /sub MAX/ /eI /sub p/ ) would indicate an effective resistance of about one ohm. Estimates of resistance based on circuit parameters (L, I, q/C) yield about one third of an ohm. To resolve these discrepancies a exclamationBexclamation probe 5 is being developed to get a better estimate of L(t), L(t) and I(t) through spatially resolved measurements. Preliminary results are reported

Comparison of Ion Beam opening switch and plasma opening switch performance

International Nuclear Information System (INIS)

Greenly, J.R.; Rondeau, G.D.; Sheldon, H.T.; Dreike, P.L.

1986-01-01

The Ion Beam opening switch (IBOS) experiment has shown that an intense charge-neutralized ion beam can carry current across a vacuum magnetically-insulated transmission line and then transfer that current to a downstream load quickly. In the IBOS experiment, a 10 cm wide parallel plate transmission line was fed up to 100 kA peak current by a 4Ω, 100 ns pulser. An ion beam of up to 100 A/cm/sup 2/, 100-300 keV protons or carbon was injected through the anode of the line in a 10 cm x 10 cm region. The line terminated in either a 15 nH short circuit or an electron diode with variable gap. The ion beam switch was able to carry up to 70 kA of line current before load current began to flow. This model is also quantitatively consistent with the observation that switch conduction current is not linear with either injected ion beam current or switch area

Particle-in-cell simulations of plasma opening switch with external magnetic field

International Nuclear Information System (INIS)

Chen Yulan; Zeng Zhengzhong; Sun Fengju

2003-01-01

Fully electromagnetic particle-in-cell simulations are performed to study the effects of an external magnetic field on coaxial plasma opening switch (POS). The simulation results show that POS opening performance can be significantly improved only when external longitudinal magnetic field coils are placed at the cathode side, and an additional azimuthal magnetic field is effective whether the central electrode is of positive or negative polarity. Voltage multiplication coefficient K rises with the additional magnetic field increasing till the electron current is completely magnetically insulated during the opening of POS

Magnetic field propagation in a two ion species planar plasma opening switch

International Nuclear Information System (INIS)

Strauss, H. R.; Doron, R.; Arad, R.; Rubinstein, B.; Maron, Y.; Fruchtman, A.

2007-01-01

Three fluid plasma evolution equations are applied to the problem of magnetic field propagation in a planar plasma opening switch. For certain initial conditions in which Hall parameter H∼1, magnetic field penetration due to the Hall field, initially, as expected, either opposes or adds to the hydromagnetic pushing, depending on the polarity of the magnetic field relative to the density gradient. Later, however, the plasma pushing by the magnetic field is found in the case studied here to modify the plasma density in a way that the density gradient tends to align with the magnetic field gradient, effectively turning off the Hall effect. The penetration of the magnetic field then ceases and plasma pushing becomes the dominant process

Dynamics of the plasma injected into the gap of a plasma opening switch across a strong magnetic field

International Nuclear Information System (INIS)

Dolgachev, G. I.; Maslennikov, D. D.; Ushakov, A. G.; Fedotkin, A. S.; Khodeev, I. A.; Shvedov, A. A.

2011-01-01

A method is proposed to increase the linear charge density transferred through a plasma opening switch (POS) and, accordingly, reduce the POS diameter by enhancing the external magnetic field in the POS gap. Results are presented from experimental studies of the dynamics of the plasma injected into the POS gap across a strong magnetic field. The possibility of closing the POS gap by the plasma injected across an external magnetic field of up to 60 kG is demonstrated.

The Energy Balance of Plasma in a Coaxial Plasma Opening Switch

International Nuclear Information System (INIS)

Xu Xiang; Wang Younian

2006-01-01

The two-dimensional energy balance in a coaxial plasma opening switch (POS) is studied based on the single-fluid magnetohydrodynamic (MHD) equations coupled with the generalized Ohm's law. The energy transfers between the plasma and the magnetic field are considered during the penetration of the magnetic field as the Ohmic heating is included in the energy-balance equation. The focus is on the energy partition between the magnetic-field energy and the dissipated magnetic-field energy in a high-density POS with different rise-in-time electric currents at the generator boundary. The simulation code is tested in two cases: the constant-in-time current case and the linear rise-in-time current case. For the sinusoidally rise-in-time current similar to that of the experiments, it is shown that at the end of the conduction phase the dissipated magnetic-field energy is 36.5% of the input electromagnetic energy, which is consistent with the experimental results

Limiting parameters of the plasma opening switch

International Nuclear Information System (INIS)

Dolgachev, G.I.; Ushakov, A.G.

2001-01-01

Implementing programs for nuclear fusion research and X-ray generation requires the creation of superpower generators based on plasma opening switches (POSs) capable of commutating currents as high as several tens of megaamperes at output voltages of up to 5 MV and higher. The physical mechanisms limiting the POS voltage are investigated. It is shown that, as the generator voltage U g increases, the voltage multiplication factor k U POS /U g (where U POS is the POS voltage) decreases. An explanation for such a dependence is proposed, and the maximum value of the POS voltage is estimated. A POS design that enables operating in the above current and voltage ranges is considered. The design is based on applying an external magnetic field to the POS interelectrode gap, increasing the initial generator voltage, and decreasing the linear (along the perimeter of the outer electrode) density of the charge passing through the POS during the conduction phase

Investigation of electron and ion flows in the microsecond plasma opening switch on the terawatt power level

International Nuclear Information System (INIS)

Bastrikov, A.N.; Bugaev, S.P.; Volkov, A.M.; Kim, A.A.; Kovalchuk, B.M.; Kokshener, V.M.; Yakovlev, V.A.; Bystritskii, V.M.; Grigoriev, S.V.; Krasik, Ya.E.

1989-01-01

The results of an investigation of ion and electron flows in the coaxial microsecond plasma opening switch (POS) at generator GIT-4 are given. The 1 mks front duration POS with outer and inner electrodes of 210 mm and 75 mm diameters respectively switched 1 MA pulse during 0.1 mks to the short circuited coaxial line with the same diameters and 120 cm of length. The polarity of the inner electrode was negative. The plasma of the POS was injected from outer electrode by 32 plasma guns of capillary type. The typical POS voltage was 0.9-1.2 MV. The calculated energy losses in the POS during the switching phase reached (0.1-0.15) MJ. The calorimetric measurements of the energy dissipated on both electrodes gave the same value. The location and distribution of the head absorbed along the POS electrodes were determined

Gap formation processes in a high-density plasma opening switch

International Nuclear Information System (INIS)

Grossmann, J.M.; Swanekamp, S.B.; Ottinger, P.F.; Commisso, R.J.; Hinshelwood, D.D.; Weber, B.V.

1995-01-01

A gap opening process in plasma opening switches (POS) is examined with the aid of numerical simulations. In these simulations, a high density (n e =10 14 --5x10 15 cm -3 ) uniform plasma initially bridges a small section of the coaxial transmission line of an inductive energy storage generator. A short section of vacuum transmission line connects the POS to a short circuit load. The results presented here extend previous simulations in the n e =10 12 --10 13 cm -3 density regime. The simulations show that a two-dimensional (2-D) sheath forms in the plasma near a cathode. This sheath is positively charged, and electrostatic sheath potentials that are large compared to the anode--cathode voltage develop. Initially, the 2-D sheath is located at the generator edge of the plasma. As ions are accelerated out of the sheath, it retains its original 2-D structure, but migrates axially toward the load creating a magnetically insulated gap in its wake. When the sheath reaches the load edge of the POS, the POS stops conducting current and the load current increases rapidly. At the end of the conduction phase a gap exists in the POS whose size is determined by the radial dimensions of the 2-D sheath. Simulations at various plasma densities and current levels show that the radial size of the gap scales roughly as B/n e , where B is the magnetic field. The results of this work are discussed in the context of long-conduction-time POS physics, but exhibit the same physical gap formation mechanisms as earlier lower density simulations more relevant to short-conduction-time POS. copyright 1995 American Institute of Physics

Experimental investigation of the material surface modification in microsecond plasma opening switch

Energy Technology Data Exchange (ETDEWEB)

Bystritskij, V; Grigor` ev, S; Kharlov, A; Sinebryukhov, A [Russian Academy of Sciences, Tomsk (Russian Federation). Institute of Electrophysics; Burkov, P [Russian Academy of Scinces, Tomsk (Russian Federation). Institute of Strength Physics and Materials Control; Grigorev, V; Koval, T [Institute of Nuclear Physics, Tomsk (Russian Federation)

1997-12-31

The paper is devoted to the investigations of the material surface modification by high power ion beam generated in microsecond plasma opening switch (MPOS). Various types of steels were investigated: stainless steel 17-4PH, carbon steel C1020, pure iron. For all these materials, the optimal regimes for irradiation were defined. A significant increase in microhardness (1.5 to 2-fold) was obtained for these materials. Numerical calculations and theoretical estimations of the ion beam-matter interaction were also performed. The advantages and problems of this approach are discussed. (author). 8 figs., 3 refs.

Enhancing the x-ray output of a single-wire explosion with a gas-puff based plasma opening switch

Science.gov (United States)

Engelbrecht, Joseph T.; Ouart, Nicholas D.; Qi, Niansheng; de Grouchy, Philip W.; Shelkovenko, Tatiana A.; Pikuz, Sergey A.; Banasek, Jacob T.; Potter, William M.; Rocco, Sophia V.; Hammer, David A.; Kusse, Bruce R.; Giuliani, John L.

2018-02-01

We present experiments performed on the 1 MA COBRA generator using a low density, annular, gas-puff z-pinch implosion as an opening switch to rapidly transfer a current pulse into a single metal wire on axis. This gas-puff on axial wire configuration was studied for its promise as an opening switch and as a means of enhancing the x-ray output of the wire. We demonstrate that current can be switched from the gas-puff plasma into the wire, and that the timing of the switch can be controlled by the gas-puff plenum backing pressure. X-ray detector measurements indicate that for low plenum pressure Kr or Xe shots with a copper wire, this configuration can offer a significant enhancement in the peak intensity and temporal distribution of radiation in the 1-10 keV range.

Pulsed power opening switch research at the University of New Mexico

International Nuclear Information System (INIS)

Humphries, S. Jr.

1987-01-01

Opening switch research at the University of New Mexico (UNM) is directed toward moderate-current (--10 kA) devices with potential applications to high-power charged particle accelerators. Two devices with the capacity for controlling gigawatt high-voltage circuits, the grid-controlled plasma flow switch and the scanned-beam switch, are under investigation. Both switches are conceptually simple; they involve little collective physics and are within the capabilities of current technology. In the plasma flow switch, the flux of electrons into a high-voltage power gap is controlled by a low-voltage control grid. Plasma generation is external to, and independent of, the power circuit. In the closed phase, plasma fills the gap so that the switch has a low on-state impedance. Pulse repetition rates in the megahertz range should be feasible. In single-shot proof-of-principle experiments, a small area switch modulated a 3-MW circuit; a 20-ns opening time was observed. The scanned-beam switch will utilize electric field deflection to direct the power of a sheet electron beam. The beam is to be alternately scanned to two inverse diodes connected to output transmission lines. The switch is expected to generate continuous-wave pulse trains for applications such as high-frequency induction linacs. Theoretical studies indicate that 10-GW devices in the 100-MHz range with 70-percent efficiency should be technologically feasible

Modeling of plasma flow switches at low, intermediate and high energies

International Nuclear Information System (INIS)

Bowers, R.L.; Brownell, J.H.; Greene, A.E.; Peterson, D.L.; Roderick, N.; Turchi, P.

1992-01-01

Inductively stored pulsed power technology has been used over the past thirty years to produce multi-megaamp currents to implode low inductance loads and produce x-radiation. Because of the large difference in timescales for the delivery of magnetic energy to the load and the desire for high power x-radiation output (short timescale for the implosion), most inductively stored systems require at least one opening switch. The design and understanding of fast, efficient opening switches for multi-megaamp systems represents a long standing problem in pulsed power research. The Los Alamos Foil Implosion Project uses inductively stored magnetic energy to implode thin metallic liners. A plasma flow switch (PFS) has been investigated as the final pulse shaping step for this systems. The PFS consists of a wire array and a barrier foil located upstream from the load region. Several stages can be identified in the performance of the plasma flow switch. These are: (1) the vaporization of the wire array; (2) the assembly of the initiated plasma on tie barrier foil to form the switch plasma; (3) the motion of the switch plasma down the coaxial barrel; and (4) current switching to the load (the actual switching stage). The fourth stage affects the switch's efficiency, as well as the quality of the load implosion. Instabilities may develop during any of these four stages, and their presence may seriously degrade the structure of the switch plasma. Two primary criteria may be used to characterize good switching. The first is switching efficiency. A second criterion is transferred to the load during or after switching. This paper summarizes the computational design of the PFS experiments carried out on Pegasus 1. We conclude by considering the implications of these results for the design of a PFS for the higher energy regime (Procyon) regime

Helical EMG module with explosive current opening switches

International Nuclear Information System (INIS)

Chernyshev, V.K.; Vakhrushev, V.V.; Volkov, G.I.; Ivanov, V.A.; Fetisov, I.K.

1990-01-01

To carry out the experimental work to study plasma properties, electromagnetic sources with 10 6 to 10 8 J of stored energy delivered to the load in microsecond time, are required. Among the current electromagnetic storage devices, the explosive magnetic generators (EMG) are of the largest energy capacity. The disadvantages of this type of generators is relatively long time (ten of microseconds) of electromagnetic energy cumulation in the deformable circuit. To reduce the time of energy transfer to the load to a microsecond range the switching scheme is generally used, where the cumulation circuit and that of the load are separated and connected in parallel via a switching element (opening switch) providing generation of desired power. In this paper, some ways and means of designing opening switches to generate high current pulses have been investigated. The opening switches to generate high current pulses have been investigated. The opening switches which operation is based on mechanic destruction of the conductor using high explosive, have the highest and most reliable performance. The authors have explored the mechanic disruption of a thin conductor (foil), the technique based on throwing the foil at the ribbed barrier of electric insulator material. The report presents the data obtained in studying the operation of this type of opening switch having cylindrical shape, 200 mm in diameter and 200 mm long, designed for generation of 5.5 MA current pulse in the load

Dynamics of the Energy Transfer to the Load During the Operation of a Plasma Opening Switch

International Nuclear Information System (INIS)

Dolinsky, Yu.; Krasik, Ya.E.; Felsteiner, J.

1999-01-01

The main efforts of the theoretical and experimental studies related to the Plasma Opening Switch (POS) have been devoted to the understanding of an anomalous fast magnetic field penetration through the plasma. At present this phenomenon can be explained based on the electron magnetohydrodynamic theory.l The second important phenomenon is related with POS opening. Existing models explain POS opening as a result of cut-off of the electron current component in the double layer2 by self-magnetic field of the POS current or by the increase of the Hall potential in the current layer due to ion erosion.3 Nevertheless both models consider POS opening in the region which was preliminary occupied by the plasma. In a recent experiment4 it was shown that the POS opening is related with a fast charged particle flow in the downstream region, namely at the load. In this work we present results of theoretical studies of the phase of the POS operation when the self-magnetic field of the POS current appears at the downstream side of the plasma. Our study has been done within the framework of two-fluid magnetohydrodynamic theory. Taking into account the Hall electric field which is responsible for a strong ion acceleration in the axial direction, we found the velocity of the ions. In addition we show, that due to the inductive electric field caused by the motion of the axial current carrying plasma, the velocity of the magnetic field penetration is equal to the Alfven velocity

Fluid simulation of the conduction phase of the plasma erosion opening switch

International Nuclear Information System (INIS)

Grossmann, J.M.; Mosher, D.; Ottinger, P.F.

1987-01-01

The conduction phase of the plasma erosion openings switch (PEOS) is studied using a 1 1/2-D electromagnetic two-fluid code. The focus of this work is on understanding how two effects, a current-limiting model of electron emission, and the magnetic insulation of electrons at the cathode, determine current conduction in the plasma. Simulations are performed in the parameter regimes of the Gamble I, POP, and PBFA II pulsed power generators, and previous low-density, short-rise time simulations of the PEOS. Fluid code results are compared to a 1-D analytic theory and to the Gamble I and POP experiments. Good agreement between theory and simulation, but mixed agreement between simulation and experiment is found. Experimental Β-field measurements on POP show weaker j x Β compression than the simulation. Current penetration and plasma current channels qualitatively similar to experimental observation are found in the Gamble I regime. However, magnetic insulation of electrons emitted from the cathode bunches the electron flow into narrower current channels than observed experimentally. In several cases, the presence of an electron-scattering or energy-loss mechanism near the cathode must be invoked to overcome magnetic insulation and widen the current channels

Study of electron and ion fluxes in a microsecond plasma switch during current switch phase at power level of 0,2TW

International Nuclear Information System (INIS)

Anan'in, P.S.; Bystritskij, V.M.; Karpov, V.B.; Krasik, Ya.E.; Lisitsin, I.V.; Sinebryukhov, A.A.

1991-01-01

Results of experimental study of dynamics of electron and ion losses in a microsecond plasma switch (PS), carring the short-circuited inductance load and operating with open potential electrode, are presented. Investigations were carried out at 'DUBL' microsecond generator with stored energy of 56 kJ and 300 kA current amplitude in inductive storage. The investigations showed that primary channel of energy losses, limiting microsecond plasma switch impedance, are energy losses: they constitute 70% of all losses under inductive load and 30% during operation with an open cathode. It was shown that ion current in PS attains its peak value by the end of conductivity phase and it does not increase in switch phase. With an open cathode, PS impedance is defined by an electron beam, forming during current switch phase and propagating towards external electrode end. In this high-current electron beam H + ions, accelerated up to 3.5-4.2 MeV energy, and outcoming from PS plasma boundary, were detected

Simulation of the Plasma Afterglow in the Discharge Gap of a Subnanosecond Switch Based on an Open Discharge in Helium

Science.gov (United States)

Alexandrov, A. L.; Schweigert, I. V.

2018-05-01

The phenomenon of subnanosecond electrical breakdown in a strong electric field observed in an open discharge in helium at pressures of 6-20 Torr can be used to create ultrafast plasma switches triggering into a conducting state for a time shorter than 1 ns. To evaluate the possible repetition rate of such a subnanosecond switch, it is interesting to study the decay dynamics of the plasma remaining in the discharge gap after ultrafast breakdown. In this paper, a kinetic model based on the particle-in-cell Monte Carlo collision method is used to study the dynamics of the plasma afterglow in the discharge gap of a subnanosecond switch operating with helium at a pressure of 6 Torr. The simulation results show that the radiative, collisional-radiative, and three-body collision recombination mechanisms significantly contribute to the afterglow decay only while the plasma density remains higher than 1012 cm-3; the main mechanism of the further plasma decay is diffusion of plasma particles onto the wall. Therefore, the effect of recombination in the plasma bulk is observed only during the first 10-20 μs of the afterglow. Over nearly the same time, plasma electrons become thermalized. The afterglow time can be substantially reduced by applying a positive voltage U c to the cathode. Since diffusive losses are limited by the ion mobility, the additional ion drift toward the wall significantly accelerates plasma decay. As U c increases from 0 to +500 V, the characteristic time of plasma decay is reduced from 35 to 10 μs.

Electron beam potential measurements on an inductive-store, opening-switch accelerator

International Nuclear Information System (INIS)

Riordan, J.C.; Goyer, J.R.; Kortbawi, D.; Meachum, J.S.; Mendenhall, R.S.; Roth, I.S.

1993-01-01

Direct measurement of the accelerating potential in a relativistic electron beam accelerator is difficult, particularly when the diode is downstream from a plasma opening switch. An indirect potential measurement can be obtained from the high energy tail of the bremsstrahlung spectrum generated as the electron beam strikes the anode. The authors' time-resolved spectrometer contains 7 silicon pin diode detectors filtered with 2 to 15 mm of lead to span an electron energy range of 0.5 to 2 MeV. A Monte-Carlo transport code was used to provide calibration curves, and the resulting potential measurements have been confirmed in experiments on the PITHON accelerator. The spectrometer has recently been deployed on PM1, an inductive-store, opening-switch testbed. The diode voltage measurements from the spectrometer are in good agreement with the diode voltage measured upstream and corrected using transmission line relations. The x-ray signal and spectral voltage rise 10 ns later than the corrected electrical voltage, however, indicating plasma motion between the opening switch and the diode

RS-20 type repetitive generator with planar configuration of plasma opening switch

Energy Technology Data Exchange (ETDEWEB)

Agalakov, V P; Barinov, N U; Belenki, G S [Kurchatov Inst., Moscow (Russian Federation); and others

1997-12-31

The existing experience with the production of repetitive rate accelerators with a high peak power (in excess of 10{sup 10} W) and an average power above 50 kW makes it possible to resolve a number of physics and technology tasks which are connected with the reliability and life of the accelerator. The design and results on optimization of a simple plasma opening switch (POS) are discussed. The final design of the POS provided voltages of up to 2 MV and had a life of more than 105 pulses including 4 hours of continuous operation under 4 Hz repetition rate and wall plug power 65 kW. This unit was tested at the RS-20 type accelerator both at the Kurchatov Institute and at the Northwest Institute of Nuclear Technology in China. (author). 5 figs., 1 ref.

Very high plasma switches. Basic plasma physics and switch technology

International Nuclear Information System (INIS)

Doucet, H.J.; Roche, M.; Buzzi, J.M.

1988-01-01

A review of some high power switches recently developed for very high power technology is made with a special attention to the aspects of plasma physics involved in the mechanisms, which determine the limits of the possible switching parameters

Two-dimensional electron flow in pulsed power transmission lines and plasma opening switches

International Nuclear Information System (INIS)

Church, B.W.; Longcope, D.W.; Ng, C.K.; Sudan, R.N.

1991-01-01

The operation of magnetically insulated transmission lines (MITL) and the interruption of current in a plasma opening switch (POS) are determined by the physics of the electrons emitted by the cathode surface. A mathematical model describes the self-consistent two-dimensional flow of an electron fluid. A finite element code, FERUS, has been developed to solve the two equations which describe Poisson's and Ampere's law in two dimensions. The solutions from this code are obtained for parameters where the electron orbits are considerably modified by the self-magnetic field of the current. Next, the self-insulated electron flow in a MITL with a step change in cross-section is studied using a conventional two-dimensional fully electromagnetic particle-in-cell code, MASK. The equations governing two-dimensional quasi-static electron flow are solved numerically by a third technique which is suitable for predicting current interruption in a POS. The object of the study is to determine the critical load impedance, Z CL , required for current interruption for a given applied voltage, cathode voltage and plasma length. (author). 9 refs, 5 figs

The influence of electrical resistivity, magnetic field strength, boundary conditions, and injection conditions on the behavior of the magnetically injected plasma in the PBFA-II opening switch

International Nuclear Information System (INIS)

Watrous, J.J.; Frese, M.H.

1993-01-01

The Plasma Opening Switch used on PBFA-II uses a source plasma which is injected into the inter-electrode gap along the field lines of a modest-strength applied poloidal magnetic field. The distribution of this plasma within the gap plays an important role in the behavior of the switch. Knowledge of this distribution is critical for performing relevant switch calculations and for interpreting experimental data. In the work reported here, the influence on that distribution of the plasma electrical resistivity, the applied magnetic field strength, and the boundary and injection conditions have been investigated with the 2 1/2-dimensional magnetohydrodynamics simulation code, MACH2. The injected plasma has density in the 10 14 cm -3 range and temperature in the several eV range. In this parameter regime, the classical collision time scale is on the order of 10 ns, which, when compared to the 100 ns time scale of the inflowing plasma, means that the plasma is classically collisionless. However, mechanisms other than classical collisions are likely to contribute to electrical resistivity. The authors have investigated the effect of an anomalous resistivity which scales with the plasma frequency, varying the scaling from the electron plasma frequency to the ion plasma frequency. They will compare these results with results based on the assumption of an ideal plasma, and discuss other anomalous resistivity models

Plasma flow switch characterization for the Los Alamos Foil Implosion Project

International Nuclear Information System (INIS)

Bowers, R.L.; Brownell, J.H.; Greene, A.E.; Peterson, D.L.

1990-01-01

The next system design under consideration for the Los Alamos Foil Implosion Project is projected to deliver tens of mega-amperes of electrical current produced by high-explosive driven flux compression generators on a time scale of about one microsecond to a load foil. The use of such generators, with time scales of order several tenths of a millisecond, leads to considerable pulse shaping problems. Previously it was noted that a commutating switch might serve as an efficient alternative to a closing switch in transferring current from a coaxial transmission line to a cylindrically imploding load. Research at the Air Force Weapons Laboratory (AFWL) has met with considerable success in efficiently transferring currents of order 10 MA to an imploding liner using the plasma flow switch concept (PFS). Besides efficiently transferring current, the plasma flow switch protects the load region from high voltages generated by an opening switch until the current is present to provide magnetic insulation. For these reasons, a PFS is being investigated as the final pulse shaping step in the design. A series of capacitor bank experiments is also being fielded to help investigate physics issues and to benchmark the codes

Outlook for the use of microsecond plasma opening switches to generate high-power nanosecond current pulses

International Nuclear Information System (INIS)

Dolgachev, G.I.; Maslennikov, D.D.; Ushakov, A.G.

2006-01-01

Paper deals with a phenomenon of current breaking in a conducting plasma volume of plasma opening switchers with a nanosecond time of energy initiation and their application in high-power generators. One determined the conditions to ensure megavolt voltages under the erosion mode making use of external applied magnetic field to ensure magnetic insulation of gap of plasma opening switchers. One studied the peculiar features of application of plasma opening switchers under 5-6 MV voltages to ensure X-ray and gamma-radiation pulses [ru

Heavy-duty explosively operated pulsed opening and closing switches

International Nuclear Information System (INIS)

Peterson, D.R.; Price, J.H.; Upshaw, J.L.; Weldon, W.F.; Zowarka, R.C.; Gully, J.H.; Spann, M.L.

1991-01-01

This paper discusses improvements to heavy duty, explosively operated, opening and closing switches to reduce component cost, installation cost, and turnaround time without sacrificing reliability. Heavy duty opening and closing switches operated by small explosive charges (50 g or less) are essential to operation of the 60 MJ Balcones power supply. The six independent modules - a 10 MJ homopolar generator (HPG) and a 6 μH storage inductor - can be discharged sequentially, a valuable feature for shaping the current pulse delivered to loads such as high-energy railguns. Each delayed inductor must be isolated from the railgun circuit with a heavy duty closing switch capable of carrying megampere currents to millisecond duration. Similar closing switches are used to crowbar the railgun as the projectile approaches the muzzle: noise reduction, reduction of muzzle arc damage, and reduction of post-launch perturbation of projectile flight. The switches - both opening and closing - are characterized by microhm resistance in the closed state. Current is carried in metallic conductors. Metal-to-metal seams which carry current are maintained in uniform high pressure contact. Efficient switching is crucial to efficient conversion: rotor kinetic energy to stored inductive energy with ∼50% efficiency, stored inductive energy to projectile kinetic energy with ∼30% efficiency. The switches must operate with a precision and repeatability of 10 -5 s, readily achievable with explosives. The opening switches must be structurally and thermally capable of carrying megampere currents for more than 100 ms (∼10 5 C) and develop 10 kV upon opening, stay open for 10 - 2 s, and safely and reliably dissipate megajoules of inductive energy in the event of a fault, a failure of the switch to operate or an attempt to commutate into an open circuit

Preliminary experiment research of explosively driven opening switch

International Nuclear Information System (INIS)

Li Xiaolin; Chen Dongqun; Li Da; Cao Shengguang; Chen Yingcong

2010-01-01

In pulse power technology field, many loads require high current pulse with fast risetime, but sometimes, the common high current pulse powers don't satisfy request, thus there need pulse erection switches of sorts to shorten pulse risetime. Explosively driven opening switch (EDOS) is a good choice, it has simple structure and excellent performance, the primary parameters of EDOS are opening time, opening resistance, opening current and dissipation energy, which determine its performance and range for applications. For this, two kinds of EDOS are designed and manufactured, in the later experiments, the power supply is a 200 μF capacitor and the conductor is 0.03 mm copper foil, the results indicate that the two kinds of EDOS have good performance, the opening time is about 1-3 μs, the opening resistance is about 1-2 Ω, the opening current is about 24-31 kA and the average dissipation energy is about 0.125-0.34 kJ per groove, the capability of conduction current is adjusted by the thickness of conductor along with different opening current. (authors)

Electronic logic to enhance switch reliability in detecting openings and closures of redundant switches

Science.gov (United States)

Cooper, James A.

1986-01-01

A logic circuit is used to enhance redundant switch reliability. Two or more switches are monitored for logical high or low output. The output for the logic circuit produces a redundant and failsafe representation of the switch outputs. When both switch outputs are high, the output is high. Similarly, when both switch outputs are low, the logic circuit's output is low. When the output states of the two switches do not agree, the circuit resolves the conflict by memorizing the last output state which both switches were simultaneously in and produces the logical complement of this output state. Thus, the logic circuit of the present invention allows the redundant switches to be treated as if they were in parallel when the switches are open and as if they were in series when the switches are closed. A failsafe system having maximum reliability is thereby produced.

Microwave plasma source having improved switching operation from plasma ignition phase to normal ion extraction phase

International Nuclear Information System (INIS)

Sakudo, N.; Abe, K.; Koike, H.; Okada, O.; Tokiguchi, K.

1985-01-01

In a microwave plasma source, a discharge space supplied with a microwave electric field is supplied with a DC magnetic field. A material to be ionized is introduced into the discharge space to produce plasma, whereby ions are extracted through an ion extracting system. A switch is provided for effecting through switching operation the change-over of the magnetic field applied to the discharge space from the intensity for the ignition of plasma to the intensity for ion extraction in succession to completion of the plasma ignition

New solid state opening switches for repetitive pulsed power technology

Energy Technology Data Exchange (ETDEWEB)

Lyubutin, S K; Mesyats, G A; Rukin, S N; Slovikovskii, B G; Turov, A M [Russian Academy of Sciences, Ekaterinburg (Russian Federation). Inst. of Electrophysics

1997-12-31

In 1991 the authors discovered a semiconductor opening switch (SOS) effect that occurs in p{sup +}-p-n-n{sup +} silicon structures at a current density of up to 60 kA/cm{sup 2}. This effect was used to develop high-power semiconductor opening switches in intermediate inductive storage circuits. The breaking power of the opening switches was as high as 5 GW, the interrupted current being up to 45 kA, reverse voltage up to 1 MV and the current interruption time between 10 and 60 ns. The opening switches were assembled from quantity-produced Russian-made rectifying diodes type SDL with hard recovery characteristic. On the basis of experimental and theoretical investigations of the SOS effect, new SOS diodes were designed and manufactured by the Electrophysical Institute. The paper gives basic parameters of the SOS diodes. The new diodes offer higher values of interrupted current and shorter times of current interruption together with a considerable increase in the energy switching efficiency. The new SOS diodes were used to develop repetitive all-solid-state pulsed generators with an output voltage of up to 250 kV, pulse repetition rate up to 5 kHz, and pulse duration between 10 and 30 ns. (author). 2 tabs., 3 figs., 4 refs.

Continuing studies of plasma erosion switches for power conditioning on multiterawatt pulsed power accelerators

International Nuclear Information System (INIS)

Stringfield, R.; Gilman, C.; James, G.; Peters, T.; Sincerny, P.; Wong, S.

1983-01-01

Recent PITHON experiments with plasma erosion switches (PES) have extended the range of operation of the switches by about 50 percent, in terms of closed time and charge passing through the switch. The quantity of charge passed through the switch has been increased to as much as 35 mC. Currents as large as 1 MA and voltages as great as 1.8 MV have been switched off to be diverted to a downstream load. The impedance of the erosion switch can be described as having three stages: 1) essentially zero impedance, 2) a transitional opening phase, and 3) an impedance which is very large (greater than 5 Ω) in comparison with the subohm downstream load. Current diagnostics, consisting of Rogowski coils and segmented shunts, have been successfully developed to monitor the current which propagates to the load region. These monitors have measured rise times as short as 38 ns and slew rates as great as 10 14 A/s at the load. With wire array loads, the pulse conditioning of the switch has been observed to reduce the magnitude of the current losses in the feed which are present when no switch is used. Correlations have been made between the switch closed time, voltage, current, and power with the feed inductance and the generator power injected into the magnetic insulated transmission line (MITL)

Density measurements of microsecond-conduction-time POS plasmas

International Nuclear Information System (INIS)

Hinshelwood, D.; Goodrich, P.J.; Weber, B.V.; Commisso, R.J.; Grossmann, J.M.; Kellogg, J.C.

1993-01-01

Measurements of the electron density in a coaxial microsecond conduction time plasma opening switch during switch operation are described. Current conduction is observed to cause a radial redistribution of the switch plasma. A local reduction in axial line density of more than an order of magnitude occurs by the time opening begins. This reduction, and the scaling of conduction current with plasma density, indicate that current conduction in this experiment is limited by hydrodynamic effects. It is hypothesized that the density reduction allows the switch to open by an erosion mechanism. Initial numerical modeling efforts have reproduced the principal observed results. A model that predicts accurately the conduction current is presented

Plasma flow switch and foil implosion experiments on Pegasus II

International Nuclear Information System (INIS)

Cochrane, J.C.; Bartsch, R.R.; Benage, J.R.; Forman, P.R.; Gribble, R.F.; Ladish, J.S.; Oona, H.; Parker, J.V.; Scudder, D.W.; Shlachter, J.S.; Wysocki, F.J.

1993-01-01

Pegasus II is the upgraded version of Pegasus, a pulsed power machine used in the Los Alamos AGEX (Above Ground EXperiments) program. A goal of the program is to produce an intense (> 100 TW) source of soft x-rays from the thermalization of the kinetic energy of a 1 to 10 MJ plasma implosion. The radiation pulse should have a maximum duration of several 10's of nanoseconds and will be used in the study of fusion conditions and material properties. The radiating plasma source will be generated by the thermalization of the kinetic energy of an imploding cylindrical, thin, metallic foil. This paper addresses experiments done on a capacitor bank to develop a switch (plasma flow switch) to switch the bank current into the load at peak current. This allows efficient coupling of bank energy into foil kinetic energy

Using Alloy to Formally Model and Reason About an OpenFlow Network Switch

OpenAIRE

Mirzaei, Saber; Bahargam, Sanaz; Skowyra, Richard; Kfoury, Assaf; Bestavros, Azer

2016-01-01

Openflow provides a standard interface for separating a network into a data plane and a programmatic control plane. This enables easy network reconfiguration, but introduces the potential for programming bugs to cause network effects. To study OpenFlow switch behavior, we used Alloy to create a software abstraction describing the internal state of a network and its OpenFlow switches. This work is an attempt to model the static and dynamic behaviour a network built using OpenFlow switches.

Experimental study on the characteristics of semiconductor opening switch

CERN Document Server

Su Jian Cang; Ding Yong Zhong; Song Zhi Min; Ding Zhen Jie; Liu Guo Zhi

2002-01-01

An experimental set-up is developed to measure the characteristics of semiconductor opening switch (SOS). The parameters, such as interruption impedance, current int eruption time, voltage gain, pulse duration and energy transfer efficiency, are studied experimentally. The experimental results show that forward pumping time and reverse pumping time are important parameters for semiconductor opening switches. The influences of forward pumping time and reverse pumping time on interruption time, voltage gain, and energy transfer efficiency are obtained. In the interruption process, the impedance variation is divided into three phases: that is rapid increasing phase, slow change phase and completely interruption phase

Computational modeling of plasma-flow switched foil implosions

International Nuclear Information System (INIS)

Lindemuth, I.R.

1985-01-01

A ''plasma-flow'', or ''commutator'', switch has been proposed as a means of achieving high dI/dt in a radially imploding metallic foil plasma. In this concept, an axially moving foil provides the initial coaxial gun discharge path for the prime power source and provides and ''integral'' inductive storage of magnetic energy. As the axially moving foil reaches the end of the coaxial gun, a radially imploding load foil is switched into the circuit. The authors have begun two-dimensional computer modeling of the two-foil implosion system. They use a magnetohydrodynamic (MHD) model which includes tabulated state and transport properties of the metallic foil material. Moving numerical grids are used to achieve adequate resolution of the moving foils. A variety of radiation models are used to compute the radiation generated when the imploding load foil converges on axis. These computations are attempting to examine the interaction of the switching foil with the load foil. In particular, they examine the relationship between foil placement and implosion quality

Wavelet Entropy-Based Traction Inverter Open Switch Fault Diagnosis in High-Speed Railways

Directory of Open Access Journals (Sweden)

Keting Hu

2016-03-01

Full Text Available In this paper, a diagnosis plan is proposed to settle the detection and isolation problem of open switch faults in high-speed railway traction system traction inverters. Five entropy forms are discussed and compared with the traditional fault detection methods, namely, discrete wavelet transform and discrete wavelet packet transform. The traditional fault detection methods cannot efficiently detect the open switch faults in traction inverters because of the low resolution or the sudden change of the current. The performances of Wavelet Packet Energy Shannon Entropy (WPESE, Wavelet Packet Energy Tsallis Entropy (WPETE with different non-extensive parameters, Wavelet Packet Energy Shannon Entropy with a specific sub-band (WPESE3,6, Empirical Mode Decomposition Shannon Entropy (EMDESE, and Empirical Mode Decomposition Tsallis Entropy (EMDETE with non-extensive parameters in detecting the open switch fault are evaluated by the evaluation parameter. Comparison experiments are carried out to select the best entropy form for the traction inverter open switch fault detection. In addition, the DC component is adopted to isolate the failure Isolated Gate Bipolar Transistor (IGBT. The simulation experiments show that the proposed plan can diagnose single and simultaneous open switch faults correctly and timely.

Magnetoresistive waves in plasmas

International Nuclear Information System (INIS)

Felber, F.S.; Hunter, R.O. Jr.; Pereira, N.R.; Tajima, T.

1982-01-01

The self-generated magnetic field of a current diffusing into a plasma between conductors can magnetically insulate the plasma. Propagation of magnetoresistive waves in plasmas is analyzed. Applications to plasma opening switches are discussed

Pulse power requirements for large aperture optical switches based on plasma electrode Pockels cells

International Nuclear Information System (INIS)

Rhodes, M.A.; Taylor, J.

1992-06-01

We discuss very large-aperture optical switches (greater than 30 x 30 cm) as an enabling technology for inertial confinement fusion drivers based on multipass laser amplifiers. Large-scale laser fusion drivers such as the Nova laser have been based on single-pass amplifier designs in part because of the unavailability of a suitable large-aperture switch. We are developing an optical switch based on a Pockels cell employing plasma-electrodes. A plasma-electrode Pockels cell (PEPC) is a longitudinal-mode Pockels cell in which a plasma discharge is formed on each side of an electro-optic crystal (typically KDP or deuterated KDP, often designated KD*P). The plasmas formed on either side of the crystal act as transparent electrodes for a switching-pulse and are intended to allow uniform charging of the entire crystal. The switching-pulse is a nominally rectangular high-voltage pulse equal to the half-wave voltage V x ( 8 kV for KD*P or 17 kV for KDP) and is applied across the crystal via the plasma-electrodes. When the crystal is charged to V x , the polarization of an incoming, linearly polarized, laser beam is rotated by 90 degree. When used in conjunction with an appropriate, passive polarizer, an optical switch is thus realized. A switch with a clear aperture of 37 x 37 cm is now in construction for the Beamlet laser which will serve as a test bed for this switch as well as other technologies required for an advanced NOVA laser design. In this paper, we discuss the unique power electronics requirements of PEPC optical switches

Operation of a semiconductor opening switch at ultrahigh current densities

International Nuclear Information System (INIS)

Lyubutin, S. K.; Rukin, S. N.; Slovikovsky, B. G.; Tsyranov, S. N.

2012-01-01

The operation of a semiconductor opening switch (SOS diode) at cutoff current densities of tens of kA/cm 2 is studied. In experiments, the maximum reverse current density reached 43 kA/cm 2 for ∼40 ns. Experimental data on SOS diodes with a p + -p-n-n + structure and a p-n junction depth from 145 to 180 μm are presented. The dynamics of electron-hole plasma in the diode at pumping and current cutoff stages is studied by numerical simulation methods. It is shown that current cutoff is associated with the formation of an electric field region in a thin (∼45 μm) layer of the structure’s heavily doped p-region, in which the acceptor concentration exceeds 10 16 cm −3 , and the current cutoff process depends weakly on the p-n junction depth.

Laser-produced dense plasma in extremely high pressure gas and its application to a plasma-bridged gap switch

International Nuclear Information System (INIS)

Yamada, J.; Okuda, A.

1989-01-01

When an extremely high pressure gas is irradiated by an intense laser light, a dense plasma produced at the focal spot moves towards the focusing lens with a high velocity. Making use of this phenomenon, a new plasma-bridged gap switch is proposed and its switching characteristics is experimentally examined. From the experiments, it is confirmed that the switching time is almost constant with the applied voltage only when the focal spot is just on the positive electrode, indicating that the bridging of gap is caused by the laser light. (author)

Characterization of the plasma-switch interaction in the LBL HIF ion source

International Nuclear Information System (INIS)

Hewett, D.W.; Rutkowski, H.L.

1990-01-01

A new way to characterize the performance of the LBL HIF ion source has been found. In the LBL source, ions are drawn from an arc-generated plasma reservoir in which the electrons are confined by a negative-biased ''switch'' mesh. Stagnation of the plasma is prevented by absorption of the excess ion flow on this mesh. The ion beam is generated by an external negative voltage that provides Child-Langmuir extraction of the ions through the switch mesh. We elucidate the physics requirements of the source and deduce switch mesh parameters needed for successful operation. 2 refs., 2 figs

The experimental investigation of explosive opening switch

Energy Technology Data Exchange (ETDEWEB)

Jiande, Zhang; Huihuang, Zhong; Chuanlu, Li; Yonggui, Liu; Dongqun, Cheng; Xianyang, Peng [National Univ. of Defense Technology, Changsha (China). Dept. of Applied Physics

1997-12-31

The explosive opening switch (EOS) used in explosive-driven magnetic-flux compression generator (EMCG) circuits was investigated. It is shown that (1) under certain conditions, the EOS voltage is hardly dependent on the size of the explosive and aluminium foil used in EOS; (2) with the explosive coated by an insulator pipe, the opening effect of EOS is better; (3) by use of EOS, a pulse with 5 kA current, 100 kV voltage and 250 ns risetime has been transferred into a resistance load. (author). 12 figs., 5 refs.

The experimental investigation of explosive opening switch

International Nuclear Information System (INIS)

Zhang Jiande; Zhong Huihuang; Li Chuanlu; Liu Yonggui; Cheng Dongqun; Peng Xianyang

1996-01-01

The explosive opening switch (EOS) used in explosive-driven magnetic-flux compression generator (EMCG) circuits was investigated. It is shown that (1) under certain conditions, the EOS voltage is hardly dependent on the size of the explosive and aluminium foil used in EOS; (2) with the explosive coated by an insulator pipe, the opening effect of EOS is better; (3) by use of EOS, a pulse with 5 kA current, 100 kV voltage and 250 ns risetime has been transferred into a resistance load. (author). 12 figs., 5 refs

Switching antipsychotics to aripiprazole or blonanserin and plasma monoamine metabolites levels in patients with schizophrenia.

Science.gov (United States)

Miura, Itaru; Shiga, Tetsuya; Katsumi, Akihiko; Kanno-Nozaki, Keiko; Mashiko, Hirobumi; Niwa, Shin-Ichi; Yabe, Hirooki

2014-03-01

Blonanserin is a novel atypical antipsychotic drug that has efficacy equal to risperidone. We investigated the effects of aripiprazole and blonanserin on clinical symptoms and plasma levels of homovanillic acid (pHVA) and 3-methoxy-4hydroxyphenylglycol in the switching strategy of schizophrenia. Twenty two Japanese patients with schizophrenia were enrolled into this open study. The antipsychotics of all patients were switched to aripiprazole or blonanserin for the improvement of clinical symptoms or side effects. Plasma monoamine metabolites levels were analyzed with high-performance liquid chromatography. There were no significant effects for time (p = 0.346) or time × group interaction (p = 0.27) on the changes of positive and negative syndrome scale (PANSS) total score, although blonanserin decreased PANSS scores. We observed negative correlation between pHVA at baseline and the change in PANSS total score (rs = -0.450, p = 0.046). We also found positive correlation between the changes in pHVA and the changes in PANSS total (rs = 0.536, p = 0.015) and positive (rs = 0.572, p = 0.008) scores. There were no differences between blonanserin and aripiprazole in the improvement of clinical symptoms. Our results suggest that pHVA may be useful indicator for the switching strategy to aripiprazole or blonanserin in schizophrenia. Copyright © 2014 John Wiley & Sons, Ltd.

Methodology, Measurement and Analysis of Flow Table Update Characteristics in Hardware OpenFlow Switches

KAUST Repository

Kuźniar, Maciej

2018-02-15

Software-Defined Networking (SDN) and OpenFlow are actively being standardized and deployed. These deployments rely on switches that come from various vendors and differ in terms of performance and available features. Understanding these differences and performance characteristics is essential for ensuring successful and safe deployments.We propose a systematic methodology for SDN switch performance analysis and devise a series of experiments based on this methodology. The methodology relies on sending a stream of rule updates, while relying on both observing the control plane view as reported by the switch and probing the data plane state to determine switch characteristics by comparing these views. We measure, report and explain the performance characteristics of flow table updates in six hardware OpenFlow switches. Our results describing rule update rates can help SDN designers make their controllers efficient. Further, we also highlight differences between the OpenFlow specification and its implementations, that if ignored, pose a serious threat to network security and correctness.

Open-switch fault detection method of an NPC converter for wind turbine systems

DEFF Research Database (Denmark)

Lee, June-Seok; Lee, Kyo-Beum; Blaabjerg, Frede

2013-01-01

In wind turbine generation (WTG) systems, the neutral-point-clamped (NPC) topology is widely used as the part of a back-to-back converter since the three-level NPC topology has more advantages than the conventional two-level inverter especially for high power. There are twelve switches in the NPC......-switch detection method of the NPC converter is different from that of the NPC inverter due to the different current paths of the NPC converter. This paper proposes the open-switch fault detection method of the NPC converter connected the permanent-magnet synchronous generator (PMSG). Moreover, the open...

Metal impurity injection into DIVA plasmas with a Q-switched laser beam

International Nuclear Information System (INIS)

Yamauchi, Toshihiko; Nagami, Masayuki; Sengoku, Seio; Kumagai, Katsuaki

1978-08-01

Metal impurity injection into DIVA plasmas with a Q-switched ruby laser beam is described. Metal materials used are aluminium and gold. The Q-switched laser beam is incident onto a thin metal film thickness about 0.2 μm coated on pyrex glass plate surface. The metal film is vaporized by the laser beam and injected into DIVA plasma. The laser-beam injection method has advantages of sharp profile of vaporized metal, easy control of vaporized metal quantity and injection rate control of metal vapor. (author)

Open data for water-related operational services, the SWITCH-ON approach

Science.gov (United States)

Mazzoli, Paolo; Bagli, Stefano; Valerio, Luzzi; Broccoli, Davide; Piccinini, Francesca

2017-04-01

Recently, a collaborative project started called SWITCH-ON (EU FP7 project No 603587) coordinated by SMHI (http://water-switch-on.eu/) as part of the contemporary European movement imposed by the INSPIRE directive and the Open Data Strategy. Among It's R&D activities GECOsistema develops and expands inside SWITCH-ON a set of online services to tackle major water related issues, from reservoir and irrigation supply, to hydrological change adaptation and hydropower potential mapping. Here we present major releases of APRIL, HyCAW and High-resolution European HydroPower Atlas; all of which make intense use of open data. APRIL is a tool for seasonal run-off forecasts, that takes advantage of open datasets or low-cost data and performs forecasts through calibrated machine learning algorithms. HyCAW is a wizard that supports the assessment of adaptation options to cope with change in the temporal distribution of water availability as well as in the total water quantity. EU HPA provides all relevant information necessary to appraise the feasibility of a micro-hydropower plant at a specific site, taking into account hydrological as well as technical and economic factors. All the tools share a common vision of the project to address water concerns and currently untapped potential of open data for improved water management across the EU. Users are guided through a Web GIS interface, created using open source Web Mapping Applications, Open-Layers and Map Server, to explore available hydrological information in the area of interest, plot available data, perform analysis, and get reports and statistics.

Spectroscopic studies of pulsed-power plasmas

International Nuclear Information System (INIS)

Maron, Y.; Arad, R.; Dadusc, G.; Davara, G.; Duvall, R.E.; Fisher, V.; Foord, M.E.; Fruchtman, A.; Gregorian, L.; Krasik, Ya.

1993-01-01

Recently developed spectroscopic diagnostic techniques are used to investigate the plasma behavior in a Magnetically Insulated Ion Diode, a Plasma Opening Switch, and a gas-puffed Z-pinch. Measurements with relatively high spectral, temporal, and spatial resolutions are performed. The particle velocity and density distributions within a few tens of microns from the dielectric-anode surface are observed using laser spectroscopy. Collective fluctuating electric fields in the plasma are inferred from anisotropic Stark broadening. For the Plasma Opening Switch experiment, a novel gaseous plasma source was developed which is mounted inside the high-voltage inner conductor. The properties of this source, together with spectroscopic observations of the electron density and particle velocities of the injected plasma, are described. Emission line intensities and spectral profiles give the electron kinetic energies during the switch operation and the ion velocity distributions. Secondary plasma ejection from the electrodes is also studied. In the Z-pinch experiment, spectral emission-line profiles are studied during the implosion phase. Doppler line shifts and widths yield the radial velocity distributions for various charge states in various regions of the plasma. Effects of plasma ejection from the cathode are also studied

High Voltage, Fast-Switching Module for Active Control of Magnetic Fields and Edge Plasma Currents

Science.gov (United States)

Ziemba, Timothy; Miller, Kenneth; Prager, James; Slobodov, Ilia

2016-10-01

Fast, reliable, real-time control of plasma is critical to the success of magnetic fusion science. High voltage and current supplies are needed to mitigate instabilities in all experiments as well as disruption events in large scale tokamaks for steady-state operation. Silicon carbide (SiC) MOSFETs offer many advantages over IGBTs including lower drive energy requirements, lower conduction and switching losses, and higher switching frequency capabilities; however, these devices are limited to 1.2-1.7 kV devices. As fusion enters the long-pulse and burning plasma eras, efficiency of power switching will be important. Eagle Harbor Technologies (EHT), Inc. developing a high voltage SiC MOSFET module that operates at 10 kV. This switch module utilizes EHT gate drive technology, which has demonstrated the ability to increase SiC MOSFET switching efficiency. The module will allow more rapid development of high voltage switching power supplies at lower cost necessary for the next generation of fast plasma feedback and control. EHT is partnering with the High Beta Tokamak group at Columbia to develop detailed high voltage module specifications, to ensure that the final product meets the needs of the fusion science community.

Open-Switch Fault Diagnosis and Fault Tolerant for Matrix Converter with Finite Control Set-Model Predictive Control

DEFF Research Database (Denmark)

Peng, Tao; Dan, Hanbing; Yang, Jian

2016-01-01

To improve the reliability of the matrix converter (MC), a fault diagnosis method to identify single open-switch fault is proposed in this paper. The introduced fault diagnosis method is based on finite control set-model predictive control (FCS-MPC), which employs a time-discrete model of the MC...... topology and a cost function to select the best switching state for the next sampling period. The proposed fault diagnosis method is realized by monitoring the load currents and judging the switching state to locate the faulty switch. Compared to the conventional modulation strategies such as carrier......-based modulation method, indirect space vector modulation and optimum Alesina-Venturini, the FCS-MPC has known and unchanged switching state in a sampling period. It is simpler to diagnose the exact location of the open switch in MC with FCS-MPC. To achieve better quality of the output current under single open...

Open-Switch Fault Detection Method of a Back-to-Back Converter Using NPC Topology for Wind Turbine Systems

DEFF Research Database (Denmark)

Lee, June-Seok; Lee, Kyo_Beum; Blaabjerg, Frede

2015-01-01

system can break down in the worst case scenario. To improve the reliability of WTG systems, an open-switch fault detection method for back-to-back converters using the NPC topology is required. This study analyzes effects of inner and outer open-switch faults of the NPC rectifier and inverter......In wind turbine generation (WTG) systems, a back-to-back converter with a neutral-point-clamped (NPC) topology is widely used because this topology has more advantages than a conventional two-level topology, particularly when operating at high power. There are 12 switches in the NPC topology....... An open-switch fault in the NPC rectifier of the back-to-back converter leads to the distortion of the input current and torque vibration in the system. Additionally, an open-switch fault in the NPC inverter of the back-to-back converter causes the distortion of the output current. Furthermore, the WTG...

Dynamic behavior of HTSC opening switch models controlled by short over-critical current pulses

International Nuclear Information System (INIS)

Agafonov, A.V.; Krastelev, E.G.; Voronin, V.S.

1999-01-01

We present results of experimental research of dynamical properties of thin films of YBa 2 Cu 3 O 7 HTSC-switch models under action of short overcritical current pulses to test this method of control of fast high-power opening switches for accelerator applications

Controlled lid-opening in Thermomyces lanuginosus lipase- An engineered switch for studying lipase function

DEFF Research Database (Denmark)

Skjold-Jørgensen, Jakob; Vind, Jesper; Moroz, Olga V.

2017-01-01

Here, we present a lipase mutant containing a biochemical switch allowing a controlled opening and closing of the lid independent of the environment. The closed form of the TlL mutant shows low binding to hydrophobic surfaces compared to the binding observed after activating the controlled switch...... inducing lid-opening. We directly show that lipid binding of this mutant is connected to an open lid conformation demonstrating the impact of the exposed amino acid residues and their participation in binding at the water-lipid interface. The switch was created by introducing two cysteine residues......-D measurements revealed a seven-fold increase in binding rate for the unlocked lipase. The TlL_locked mutant shows structural changes across the protein important for understanding the mechanism of lid-opening and closing. Our experimental results reveal sites of interest for future mutagenesis studies aimed...

Investigation of thick grid plasma switches for thermionic system output voltage

International Nuclear Information System (INIS)

Alekseev, N.I.; Kaplan, V.B.; Martsinovski, A.M.

1992-01-01

Plasma switches (Cs and Cs-Ba tacitrons PS) with thick grid have grid with thickness more than mesh aperture size. These grids have some advantages as compared with small-scale/1.2/ones. For instance, much more electrical strength. This paper contains the thick-grid investigation results: the grid controls efficiency, the plasma parameters, probe researches of these parameters at conductive state and their variety during the process of quenching. The results showed the thick-grid PS plasma differed from the thin-grid PS significantly at the stationary state as well as by quenching dynamic features

Numerical resolution of a bi-temperature MHD model with a general Ohm's law: Roe solver - Front-tracking - Nonlinear transport equations with discontinuous coefficients. Simulation of a Plasma Opening Switch

International Nuclear Information System (INIS)

Brassier, Stephane

1998-01-01

The Magnetohydrodynamic (MHD) equations represent the coupling between fluid dynamics equations and Maxwell's equations. We consider here a new MHD model with two temperatures. A Roe scheme is first constructed in the one dimensional case, for a multi-species model and a general equation of state. The multidimensional case is treated thanks to the Powell approach. The notion of Roe-Powell matrix, generalization of the notion of Roe matrix for multidimensional MHD, allows us to develop an original scheme on a curvilinear grid. We focus on a second part on the modelling of a Plasma Opening Switch (POS). A front-tracking method is first set up, in order to correctly handle the deformation of the front between the vacuum and the plasma. Besides, by taking into account a general Ohm's law, we have to deal with the Hall effect, which leads to nonlinear transport equations with discontinuous coefficients. Several numerical schemes are proposed and tested on a variety of test cases. This work has allowed us to construct an industrial MHD code, intended to handle complex flows and in particular to correctly simulate the behaviour of the POS. (author) [fr

Explosively formed fuse opening switches for use in flux-compression generator circuits

International Nuclear Information System (INIS)

Goforth, J.H.; Marsh, S.P.

1990-01-01

Explosive-driven magnetic flux compression generators (explosive generators) provide for the generation of large amounts of energy compactly stored in a magnetic field. Opening switches for use in explosive generator circuits allow the energy to be used for applications requiring higher power than can be developed by the generators themselves. The authors have developed a type of opening switch that they describe as an explosively formed fuse (EEF). These switches are well suited to explosive generator circuits and provide a considerable enhancement of explosive pulsed-power capability. The authors first experiments with explosively formed fuses occurred while attempting to utilize the enhanced pressure developed in the high-pressure interaction between two detonation fronts. In these tests they attempted to use the interaction to sever conducting plates along lines perpendicular to current flow. The technique worked to some extent, and to ascertain how much advantage was gained from the high-pressure interaction, they substituted an areal detonation in place of the discrete lines required to produce lines of interaction. This paper describes the authors development effort, the state of the art, and the different manifestations of their technique

A technique to reduce plasma armature formation voltage

International Nuclear Information System (INIS)

Jamison, K.A.; Littrell, D.M.

1991-01-01

The initiation of a plasma armature by foil vaporization in a railgun is often accompanied by a large, fast, voltage transient appearing on both the breech and muzzle of the gun. For a railgun driven by an inductor/opening switch power supply, this voltage transient becomes a concern during current commutation from the switch to the railgun. To lessen the requirements on the opening switch, techniques must be found to reduce the armature formation voltage. This paper presents the experimental results from railgun firings at AFATL's Electromagnetic Launcher Basic Research Facility (Site A-15, Eglin Air Force Base, Florida) using different shapes of initiation foils. These foils have been designed to vaporize into a plasma armature with reduced transient voltages. A design criteria was developed to ensure that all portions of the foil vaporize at slightly different times

Dependence of polar effect on parameters of coaxial plasma-erosive switches

International Nuclear Information System (INIS)

Bystritskij, V.M.; Ivanov, I.B.; Krasik, Ya.E.; Ryzhakin, N.N.; Sinebryukhov, A.A.; Tolmacheva, V.G.

1988-01-01

The results of experimental investigations and numerical simulation of the polar effect in a coaxial plasma-erosive switch (PES) established in a circuit of a strong-current nanosecond accelerator are presented. PES characteristics (energy losses, impedance, rate of its increase, etc.) are investigated depending on mutual direction of accelerator current and plasma flow as well as on the cathode radius in the PES region. It is experimentally shown that the magnetic fields near the cathode determined by this electrode radius influences mainly on PES characteristics. Mutual direction of accelerator current and plasma flow is the second significance factor influencing on PES characteristics. The optimal mode of PES operation is realized when providing the less with respect to the positive electrode, cathode radius and coinciding in direction accelerator current and plasma flow. Numerical simulation of dynamic processes in coaxial PES for different ratios of cathode and anode radii and mutual directions of accelerator current and plasma flow gives qualitative agreement with the experimental results

Multichannel microwave interferometer with an antenna switching system for electron density measurement in a laboratory plasma experiment

Energy Technology Data Exchange (ETDEWEB)

Kawamori, Eiichirou; Lin, Yu-Hsiang [Institute of Space and Plasma Sciences, National Cheng Kung University, Tainan 70101, Taiwan (China); Mase, Atsushi [Art, Science and Technology Center for Cooperative Research, Kyushu University, Kasuga 816-8580 (Japan); Nishida, Yasushi; Cheng, C. Z. [Institute of Space and Plasma Sciences, National Cheng Kung University, Tainan 70101, Taiwan (China); Plasma and Space Science Center, National Cheng Kung University, Tainan 70101, Taiwan (China)

2014-02-15

This study presents a simple and powerful technique for multichannel measurements of the density profile in laboratory plasmas by microwave interferometry. This technique uses electromechanical microwave switches to temporally switch the connection between multiple receiver antennas and one phase-detection circuit. Using this method, the phase information detected at different positions is rearranged into a time series that can be acquired from a minimum number of data acquisition channels (e.g., two channels in the case of quadrature detection). Our successfully developed multichannel microwave interferometer that uses the antenna switching method was applied to measure the radial electron density profiles in a magnetized plasma experiment. The advantage of the proposed method is its compactness and scalability to multidimensional measurement systems at low cost.

IEEE conference record -- Abstracts: 1996 IEEE international conference on plasma science

International Nuclear Information System (INIS)

Anon.

1996-01-01

This meeting covered the following topics: space plasmas; non-equilibrium plasma processing; computer simulation of vacuum power tubes; vacuum microelectronics; microwave systems; basic phenomena in partially ionized gases -- gaseous electronics, electrical discharges; ball lightning/spherical plasma configuration; plasma diagnostics; plasmas for lighting; dense plasma focus; intense ion and electron beams; plasma, ion, and electron sources; flat panel displays; fast z-pinches and x-ray lasers; environmental/energy issues in plasma science; thermal plasma processing; computational plasma physics; magnetic confinement fusion; microwave-plasma interactions; space plasma engineering; EM and ETH launchers; fast wave devices; intense beam microwaves; slow wave devices; space plasma measurements; basic phenomena in fully ionized plasma -- waves, instabilities, plasma theory, etc; plasma closing switches; fast opening switches; and laser-produced plasma. Separate abstracts were prepared for most papers in this conference

Computer simulation of plasma turbulence in open systems

International Nuclear Information System (INIS)

Sigov, Yu.S.

1982-01-01

A short review of the results of kinetic simulation of collective phenomena in open plasma systems with the variable total energy and number of particles, i.e., the particle and energy fluxes on boundary surfaces and/or their internal sources and channels is given. Three specific problems are considered in different detail for such systems in one-dimensional geometry: the generation and evolution of double layers in a currently unstable plasma; the collisionless relaxation of strongly non-equilibrium electron distributions; the Langmuir collapse and strong electrostatic turbulence in systems with parametric excitation of a plasma by an external pumping wave and with cooling the fast non-Maxwell electrons. In all these cases the non-linearity and a collective character of processes give examples of new dissipative plasma structures that essentially widen our idea about the nature of the plasma turbulence in non-homogeneous open systems. (Auth.)

Diagnosis and Tolerant Strategy of an Open-Switch Fault for T-type Three-Level Inverter Systems

DEFF Research Database (Denmark)

Choi, Uimin; Lee, Kyo Beum; Blaabjerg, Frede

2014-01-01

This paper proposes a new diagnosis method of an open-switch fault and fault-tolerant control strategy for T-type three-level inverter systems. The location of faulty switch can be identified by the average of normalized phase current and the change of the neutral-point voltage. The proposed fault......-tolerant strategy is explained by dividing into two cases: the faulty condition of half-bridge switches and the neutral-point switches. The performance of the T-type inverter system improves considerably by the proposed fault tolerant algorithm when a switch fails. The roposed method does not require additional...... components and complex calculations. Simulation and experimental results verify the feasibility of the proposed fault diagnosis and fault-tolerant control strategy....

Rilpivirine exposure in plasma and sanctuary site compartments after switching from nevirapine-containing combined antiretroviral therapy.

Science.gov (United States)

Mora-Peris, Borja; Watson, Victoria; Vera, Jaime H; Weston, Rosy; Waldman, Adam D; Kaye, Steve; Khoo, Saye; Mackie, Nicola E; Back, David; Winston, Alan

2014-06-01

Pharmacokinetic parameters following modifications to antiretroviral therapy and sanctuary site exposure are often unknown for recently licensed antiretrovirals. We assessed plasma, CSF and seminal plasma (SP) exposure of rilpivirine after switching from nevirapine. HIV-infected male subjects receiving tenofovir/emtricitabine/nevirapine (245/200/400 mg) once daily switched to tenofovir/emtricitabine/rilpivirine (245/200/25 mg) once daily for 60 days when CSF and semen samples were collected. Mean and individual plasma concentrations of nevirapine and rilpivirine were compared with the proposed plasma target concentration for nevirapine (3000 ng/mL) and the protein binding-adjusted EC90 for rilpivirine (12.1 ng/mL). Mean rilpivirine CSF and SP concentrations were calculated and individual values compared with the EC50 and EC90 for wild-type virus (0.27 and 0.66 ng/mL, respectively). Of 13 subjects completing study procedures including CSF examination, 8 provided seminal samples. By day 3, the mean plasma rilpivirine trough concentration was 29.7 ng/mL (95% CI: 23.8-37). No patient presented rilpivirine plasma concentrations under the proposed threshold. The mean rilpivirine concentration in CSF was 0.8 ng/mL (95% CI: 0.7-1.0), representing a CSF : plasma ratio of 1.4%, with concentrations above the EC90 in 85% (11/13) of patients. In SP, the mean rilpivirine concentration was 4.9 ng/mL (95% CI: 3.3-7.2), representing an SP : plasma ratio of 9.5%, with all concentrations above the EC90. Switching from nevirapine- to rilpivirine-containing antiretroviral therapy was safe and well tolerated, with plasma rilpivirine concentrations above the protein binding-adjusted EC90 in all subjects. Rilpivirine concentrations were always above the EC50 in the CSF and the EC90 in SP. © The Author 2014. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Diagnosis method of an open-switch fault for a grid-connected T-type three-level inverter system

DEFF Research Database (Denmark)

Choi, U. M.; Lee, K. B.; Blaabjerg, Frede

2012-01-01

-tolerant control algorithm can be used when the open switch fault occurs in the middle switches. It is achieved by simply modifying the conventional SVM method. The proposed methods are advantageous as they do not require additional sensors and they do not involve complex calculations. Therefore, this method...

Gaseous material capacity of open plasma jet in plasma spray-physical vapor deposition process

Science.gov (United States)

Liu, Mei-Jun; Zhang, Meng; Zhang, Qiang; Yang, Guan-Jun; Li, Cheng-Xin; Li, Chang-Jiu

2018-01-01

Plasma spray-physical vapor deposition (PS-PVD) process, emerging as a highly efficient hybrid approach, is based on two powerful technologies of both plasma spray and physical vapor deposition. The maximum production rate is affected by the material feed rate apparently, but it is determined by the material vapor capacity of transporting plasma actually and essentially. In order to realize high production rate, the gaseous material capacity of plasma jet must be fundamentally understood. In this study, the thermal characteristics of plasma were measured by optical emission spectrometry. The results show that the open plasma jet is in the local thermal equilibrium due to a typical electron number density from 2.1 × 1015 to 3.1 × 1015 cm-3. In this condition, the temperature of gaseous zirconia can be equal to the plasma temperature. A model was developed to obtain the vapor pressure of gaseous ZrO2 molecules as a two dimensional map of jet axis and radial position corresponding to different average plasma temperatures. The overall gaseous material capacity of open plasma jet, take zirconia for example, was further established. This approach on evaluating material capacity in plasma jet would shed light on the process optimization towards both depositing columnar coating and a high production rate of PS-PVD.

Energy storage, compression, and switching. Vol. 2

International Nuclear Information System (INIS)

Nardi, V.; Bostick, W.H.; Sahlin, H.

1983-01-01

This book is a compilation of papers presented at the Second International Conference on Energy Storage, Compression, and Switching, which was held in order to assemble active researchers with a major interest in plasma physics, electron beams, electric and magnetic energy storage systems, high voltage and high current switches, free-electron lasers, and pellet implosion plasma focus. Topics covered include: Slow systems: 50-60 Hz machinery, homopolar generators, slow capacitors, inductors, and solid state switches; Intermediate systems: fast capacitor banks; superconducting storage and switching; gas, vacuum, and dielectric switching; nonlinear (magnetic) switching; imploding liners capacitors; explosive generators; and fuses; and Fast systems: Marx, Blumlein, oil, water, and pressurized water dielectrics; switches; magnetic insulation; electron beams; and plasmas

An Open Source Computational Framework for Uncertainty Quantification of Plasma Chemistry Models

OpenAIRE

Zaheri Sarabi, Shadi

2017-01-01

The current thesis deals with the development of a computational framework for performing plasma chemistry simulations and their uncertainty quantification analysis by suitably combining and extending existing open source computational tools. A plasma chemistry solver is implemented in the OpenFOAM C++ solver suite. The OpenFOAM plasma chemistry application solves the species conservation equations and the electron energy equation by accounting suitably for various production and loss terms b...

Plasma filled diodes and application to a PEOS

International Nuclear Information System (INIS)

Grossmann, J.M.; Ottinger, P.F.; Drobot, A.T.; Seftor, L.

1985-01-01

Pinched beam diodes generally begin operation at large impedances until the diode has had time to turn on (at which point strong electric fields turn on electric emission at the cathode). Current turn-on is accompanied by a sharp drop in impedance and is accomplished initially through space charge limited flow. As the current increases, the diode impedance will be determined by critical current flow when the electron beam pinches. Eventually the diode shorts out by gap closure as the high density electrode plasmas expand cross the AK gap. After turn-on, then, the diode acts as a low impedance load which is favorable for coupling to a PEOS by allowing for strong insulation of the electron flow from the PEOS to the load. It would be advantageous when using a PEOS to have the impedance of the diode low even at early times. This can be accomplished by introducing a low density plasma in the region between the cathode and the anode. The plasma initially presents the PEOS with a low impedance current path at the load as the switch opens - thereby reducing current losses upstream of the load. As the switch opens, the impedance of the diode can increase as the diode plasma erodes away, and the diode gap opens

Analysis on discharge process of a plasma-jet triggered gas spark switch

Science.gov (United States)

Weihao, TIE; Cui, MENG; Yuting, ZHANG; Zirang, YAN; Qiaogen, ZHANG

2018-01-01

The plasma-jet triggered gas switch (PJTGS) could operate at a low working coefficient with a low jitter. We observed and analyzed the discharge process of the PJTGS at the lowest working coefficient of 47% with the trigger voltage of 40 kV and the pulse energy of 2 J to evaluate the effect of the plasma jet. The temporal and spatial evolution and the optical emission spectrum of the plasma jet were captured. And the spraying delay time and outlet velocity under different gas pressures were investigated. In addition, the particle in cell with Monte Carlo collision was employed to obtain the particle distribution of the plasma jet varying with time. The results show that, the plasma jet generated by spark discharge is sprayed into a spark gap within tens of nanoseconds, and its outlet velocity could reach 104 m s-1. The plasma jet plays a non-penetrating inducing role in the triggered discharge process of the PJTGS. On the one hand, the plasma jet provides the initial electrons needed by the discharge; on the other hand, a large number of electrons focusing on the head of the plasma jet distort the electric field between the head of the plasma jet and the opposite electrode. Therefore, a fast discharge originated from the plasma jet is induced and quickly bridges two electrodes.

Radiation yield from SHIVA Star plasma flow switch driven fast liner implosions

International Nuclear Information System (INIS)

Degnan, J.H.; Baker, W.L.; Beason, J.D.

1987-01-01

A 2.5 Terawatt 0.5 MJ isotropic equivalent radiation yield was obtained in a SHIVA Star plasma flow switch driven fast liner implosion. The 1313 μF 80 kV discharge delivered 13 MA to a coaxial vacuum inductive store with a plasma armature. Over 9.4 MA current was plasma flow switched to the implosion load (>90% of the gun muzzle current at that time). The load wa a 5 cm radius, 2 cm tall, 200 μg/cm/sup 2/ aluminum plated Formvar cylindrical foil. The radiation pulse was measured with an array of seven X-ray diodes (XRDs). The XRDs all had aluminum photocathodes, a variety of filters and nickel mesh to reduce the incident X-ray photon flux to avoid Child-Langmuir saturation. The filters were chosen so that the authors had seven different diode response functions covering the energy range from 15 eV to about 3 keV. The filters were mounted remote (about 30 cm) from the XRDs. The anode mesh served as part of the mesh array. The distance between meshes was greater than 10 cm. Each XRD had a 5 cm diameter cathode with an aperture limited to a 2 cm diameter. The XRD anode-cathode gap was 1 cm and the bias was 5 kV. The theoretical Child-Langmuir saturation signal was 125 V with 50 Ω termination. The maximum observed signal was 75 V

Note: Design and investigation of a multichannel plasma-jet triggered gas switch.

Science.gov (United States)

Tie, Weihao; Liu, Xuandong; Zhang, Qiaogen; Liu, Shanhong

2014-07-01

We described the fabrication and testing of a multichannel plasma-jet triggered gas switch (MPJTGS). A novel six-channel annular micro-plasma-gun was embedded in the trigger electrode to generate multichannel plasma jets as a nanosecond trigger pulse arrived. The gas breakdown in multiple sites of the spark gap was induced and fixed around jet orifices by the plasma jets. We tested the multichannel discharge characteristics of the MPJTGS in two working modes with charge voltage of 50 kV, trigger voltage of +40 kV (25 ns rise time), and trigger energy of 240 J, 32 J, and 2 J, respectively, at different working coefficients. Results show that the average number of discharge channels increased as the trigger energy increased, and decreased as the working coefficient decreased. At a working coefficient of 87.1% and trigger energy of 240 J, the average number of discharge channels in Mode II could reach 4.1.

plasmaFoam: An OpenFOAM framework for computational plasma physics and chemistry

Science.gov (United States)

Venkattraman, Ayyaswamy; Verma, Abhishek Kumar

2016-09-01

As emphasized in the 2012 Roadmap for low temperature plasmas (LTP), scientific computing has emerged as an essential tool for the investigation and prediction of the fundamental physical and chemical processes associated with these systems. While several in-house and commercial codes exist, with each having its own advantages and disadvantages, a common framework that can be developed by researchers from all over the world will likely accelerate the impact of computational studies on advances in low-temperature plasma physics and chemistry. In this regard, we present a finite volume computational toolbox to perform high-fidelity simulations of LTP systems. This framework, primarily based on the OpenFOAM solver suite, allows us to enhance our understanding of multiscale plasma phenomenon by performing massively parallel, three-dimensional simulations on unstructured meshes using well-established high performance computing tools that are widely used in the computational fluid dynamics community. In this talk, we will present preliminary results obtained using the OpenFOAM-based solver suite with benchmark three-dimensional simulations of microplasma devices including both dielectric and plasma regions. We will also discuss the future outlook for the solver suite.

Bone Marrow Mesenchymal Stem Cells Enhance the Differentiation of Human Switched Memory B Lymphocytes into Plasma Cells in Serum-Free Medium

Directory of Open Access Journals (Sweden)

Guillaume Bonnaure

2016-01-01

Full Text Available The differentiation of human B lymphocytes into plasma cells is one of the most stirring questions with regard to adaptive immunity. However, the terminal differentiation and survival of plasma cells are still topics with much to be discovered, especially when targeting switched memory B lymphocytes. Plasma cells can migrate to the bone marrow in response to a CXCL12 gradient and survive for several years while secreting antibodies. In this study, we aimed to get closer to niches favoring plasma cell survival. We tested low oxygen concentrations and coculture with mesenchymal stem cells (MSC from human bone marrow. Besides, all cultures were performed using an animal protein-free medium. Overall, our model enables the generation of high proportions of CD38+CD138+CD31+ plasma cells (≥50% when CD40-activated switched memory B lymphocytes were cultured in direct contact with mesenchymal stem cells. In these cultures, the secretion of CXCL12 and TGF-β, usually found in the bone marrow, was linked to the presence of MSC. The level of oxygen appeared less impactful than the contact with MSC. This study shows for the first time that expanded switched memory B lymphocytes can be differentiated into plasma cells using exclusively a serum-free medium.

Analytical Performance Evaluation of Different Switch Solutions

Directory of Open Access Journals (Sweden)

Francisco Sans

2013-01-01

Full Text Available The virtualization of the network access layer has opened new doors in how we perceive networks. With this virtualization of the network, it is possible to transform a regular PC with several network interface cards into a switch. PC-based switches are becoming an alternative to off-the-shelf switches, since they are cheaper. For this reason, it is important to evaluate the performance of PC-based switches. In this paper, we present a performance evaluation of two PC-based switches, using Open vSwitch and LiSA, and compare their performance with an off-the-shelf Cisco switch. The RTT, throughput, and fairness for UDP are measured for both Ethernet and Fast Ethernet technologies. From this research, we can conclude that the Cisco switch presents the best performance, and both PC-based switches have similar performance. Between Open vSwitch and LiSA, Open vSwitch represents a better choice since it has more features and is currently actively developed.

Effects of plasma treatment time on surface characteristics of indium-tin-oxide film for resistive switching storage applications

International Nuclear Information System (INIS)

Chen, Po-Hsun; Chang, Ting-Chang; Chang, Kuan-Chang; Tsai, Tsung-Ming; Pan, Chih-Hung; Shih, Chih-Cheng; Wu, Cheng-Hsien; Yang, Chih-Cheng; Chen, Wen-Chung; Lin, Jiun-Chiu; Wang, Ming-Hui; Zheng, Hao-Xuan; Chen, Min-Chen; Sze, Simon M.

2017-01-01

In this paper, we implement a post-oxidation method to modify surface characteristics of indium tin oxide (ITO) films by using an O_2 inductively coupled plasma (ICP) treatment. Based on field emission-scanning electron microscope (FE-SEM) and atomic force microscope (AFM) analysis, we found that the surface morphologies of the ITO films become slightly flatter after the O_2 plasma treatment. The optical characteristics and X-ray diffraction (XRD) experiments of either pure ITO or O_2 plasma treated ITO films were also verified. Even though the XRD results showed no difference from bulk crystallizations, the oxygen concentrations increased at the film surface after O_2 plasma treatment, according to the XPS inspection results. Moreover, this study investigated the effects of two different plasma treatment times on oxygen concentration in the ITO films. The surface sheet resistance of the plasma treated ITO films became nearly non-conductive when measured with a 4-point probe. Finally, we applied the O_2 plasma treated ITO films as the insulator in resistive random access memory (RRAM) to examine their potential for use in resistive switching storage applications. Stable resistance switching characteristics were obtained by applying the O_2 plasma treatment to the ITO-based RRAM. We also confirmed the relationship between plasma treatment time and RRAM performance. These material analyses and electrical measurements suggest possible advantages in using this plasma treatment technique in device fabrication processes for RRAM applications.

Effects of plasma treatment time on surface characteristics of indium-tin-oxide film for resistive switching storage applications

Energy Technology Data Exchange (ETDEWEB)

Chen, Po-Hsun [Department of Physics, National Sun Yat-Sen University, Kaohsiung 804, Taiwan, ROC (China); Chang, Ting-Chang, E-mail: tcchang3708@gmail.com [Department of Physics, National Sun Yat-Sen University, Kaohsiung 804, Taiwan, ROC (China); Advanced Optoelectronics Technology Center, National Cheng Kung University, Tainan 701, Taiwan, ROC (China); Chang, Kuan-Chang, E-mail: kcchang@pkusz.edu.cn [Department of Materials and Optoelectronic Science, National Sun Yat-Sen University, Kaohsiung 804, Taiwan, ROC (China); School of Electronic and Computer Engineering, Peking University, Shenzhen 518055 (China); Tsai, Tsung-Ming; Pan, Chih-Hung; Shih, Chih-Cheng; Wu, Cheng-Hsien; Yang, Chih-Cheng; Chen, Wen-Chung; Lin, Jiun-Chiu; Wang, Ming-Hui [Department of Materials and Optoelectronic Science, National Sun Yat-Sen University, Kaohsiung 804, Taiwan, ROC (China); Zheng, Hao-Xuan; Chen, Min-Chen [Department of Physics, National Sun Yat-Sen University, Kaohsiung 804, Taiwan, ROC (China); Sze, Simon M. [Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, Hsinchu 300, Taiwan, ROC (China)

2017-08-31

In this paper, we implement a post-oxidation method to modify surface characteristics of indium tin oxide (ITO) films by using an O{sub 2} inductively coupled plasma (ICP) treatment. Based on field emission-scanning electron microscope (FE-SEM) and atomic force microscope (AFM) analysis, we found that the surface morphologies of the ITO films become slightly flatter after the O{sub 2} plasma treatment. The optical characteristics and X-ray diffraction (XRD) experiments of either pure ITO or O{sub 2} plasma treated ITO films were also verified. Even though the XRD results showed no difference from bulk crystallizations, the oxygen concentrations increased at the film surface after O{sub 2} plasma treatment, according to the XPS inspection results. Moreover, this study investigated the effects of two different plasma treatment times on oxygen concentration in the ITO films. The surface sheet resistance of the plasma treated ITO films became nearly non-conductive when measured with a 4-point probe. Finally, we applied the O{sub 2} plasma treated ITO films as the insulator in resistive random access memory (RRAM) to examine their potential for use in resistive switching storage applications. Stable resistance switching characteristics were obtained by applying the O{sub 2} plasma treatment to the ITO-based RRAM. We also confirmed the relationship between plasma treatment time and RRAM performance. These material analyses and electrical measurements suggest possible advantages in using this plasma treatment technique in device fabrication processes for RRAM applications.

Pseudospark switches

International Nuclear Information System (INIS)

Billault, P.; Riege, H.; Gulik, M. van; Boggasch, E.; Frank, K.

1987-01-01

The pseudospark discharge is bound to a geometrical structure which is particularly well suited for switching high currents and voltages at high power levels. This type of discharge offers the potential for improvement in essentially all areas of switching operation: peak current and current density, current rise, stand-off voltage, reverse current capability, cathode life, and forward drop. The first pseudospark switch was built at CERN at 1981. Since then, the basic switching characteristics of pseudospark chambers have been studied in detail. The main feature of a pseudospark switch is the confinement of the discharge plasma to the device axis. The current transition to the hollow electrodes is spread over a rather large surface area. Another essential feature is the easy and precise triggering of the pseudospark switch from the interior of the hollow electrodes, relatively far from the main discharge gap. Nanosecond delay and jitter values can be achieved with trigger energies of less than 0.1 mJ, although cathode heating is not required. Pseudospark gaps may cover a wide range of high-voltage, high-current, and high-pulse-power switching at repetition rates of many kilohertz. This report reviews the basic researh on pseudospark switches which has been going on at CERN. So far, applications have been developed in the range of thyratron-like medium-power switches at typically 20 to 40 kV and 0.5 to 10 kA. High-current pseudospark switches have been built for a high-power 20 kJ pulse generator which is being used for long-term tests of plasma lenses developed for the future CERN Antiproton Collector (ACOL). The high-current switches have operated for several hundred thousand shots, with 20 to 50 ns jitter at 16 kV charging voltage and more than 100 kA peak current amplitude. (orig.)

Numerical Simulation of Plasma Actuator Using OpenFOAM

OpenAIRE

H. Yazdani; K. Ghorbanian

2016-01-01

This paper deals with modeling and simulation of the plasma actuator with OpenFOAM. Plasma actuator is one of the newest devices in flow control techniques which can delay separation by inducing external momentum to the boundary layer of the flow. The effects of the plasma actuators on the external flow are incorporated into Navier-Stokes computations as a body force vector which is obtained as a product of the net charge density and the electric field. In order to compute this body force vec...

A 3-MA compact-toroid-plasma-flow-switched plasma focus demonstration experiment on Shiva Star

Energy Technology Data Exchange (ETDEWEB)

Kiuttu, G F; Degnan, J H [Phillips Lab., Kirtland AFB, NM (United States). High Energy Sources Div.; Graham, J D [Maxwell Labs., Albuquerque, NM (United States); and others

1997-12-31

A novel dense plasma focus experiment using the Shiva Star capacitor bank is described. The experiment uses a compact toroid (CT) magnetized plasma flow switch (PFS) to initiate the focus implosion. The CT armature stably and reproducibly translates up to 3 MA from the vacuum feed region through coaxial electrodes to the gas puff central load. The inertia of the 1 mg CT and the work that must be done in compressing the internal magnetic fields during the translation provide a delay in current delivery to the pinch of 5 - 10 {mu}s, which matches the bank quarter cycle time relatively well. Effectiveness of the current delivery was monitored primarily by inductive probes in the PFS region, fast photography of the focus, and x-ray and neutron measurements of the pinch. K shell x-ray yields using neon gas were as high as 1 kJ, and 10{sup 8} neutrons were produced in a deuterium gas focus. (author). 4 figs., 10 refs.

A 3-MA compact-toroid-plasma-flow-switched plasma focus demonstration experiment on Shiva Star

International Nuclear Information System (INIS)

Kiuttu, G.F.; Degnan, J.H.

1996-01-01

A novel dense plasma focus experiment using the Shiva Star capacitor bank is described. The experiment uses a compact toroid (CT) magnetized plasma flow switch (PFS) to initiate the focus implosion. The CT armature stably and reproducibly translates up to 3 MA from the vacuum feed region through coaxial electrodes to the gas puff central load. The inertia of the 1 mg CT and the work that must be done in compressing the internal magnetic fields during the translation provide a delay in current delivery to the pinch of 5 - 10 μs, which matches the bank quarter cycle time relatively well. Effectiveness of the current delivery was monitored primarily by inductive probes in the PFS region, fast photography of the focus, and x-ray and neutron measurements of the pinch. K shell x-ray yields using neon gas were as high as 1 kJ, and 10 8 neutrons were produced in a deuterium gas focus. (author). 4 figs., 10 refs

Plasma x-ray radiation source.

Science.gov (United States)

Popkov, N F; Kargin, V I; Ryaslov, E A; Pikar', A S

1995-01-01

This paper gives the results of studies on a plasma x-ray source, which enables one to obtain a 2.5-krad radiation dose per pulse over an area of 100 cm2 in the quantum energy range from 20 to 500 keV. Pulse duration is 100 ns. Spectral radiation distributions from a diode under various operation conditions of a plasma are obtained. A Marx generator served as an initial energy source of 120 kJ with a discharge time of T/4 = 10-6 s. A short electromagnetic pulse (10-7 s) was shaped using plasma erosion opening switches.

Progress in switching technology for METS systems

International Nuclear Information System (INIS)

Honig, E.M.; Swannack, C.E.; Warren, R.W.; Whitaker, D.H.

1977-01-01

Three distinct sets of switching requirements have emerged from design optimization studies of large superconducting magnetic energy storage systems, such as the METS system to power the adiabatic plasma compression field in the proposed theta-pinch SFTR. Extremely low joule loss cryogenic disconnects are required between storage coils in the liquid helium environment to allow charging the coils in series over a prolonged time, then to isolate the coils for parallel fast discharging into the load. Another switch must break the current in the series charging loop and absorb the energy from the stray inductance. This action will allow the subsequent opening of the cryogenic disconnects under near zero current condition. The current now has been transferred to the many paralleled circuits, each containing a high current, high voltage interrupter. The opening and arc commutation of the interrupter starts the energy transfer into the load. The primary activities associated with cryogenic disconnect have been testing and development of contact materials, configurations, and closing forces for carrying 26 kA with a resistance less than 40 nΩ, and development of an actuating system that is both reliable and fast acting in a liquid helium environment. The charging loop switch will include a continuous duty switch and a vacuum interrupter. The continuous duty switch resistance can be an order of magnitude larger than that of the cryogenic disconnect because it does not present a refrigeration load. The HVDC interrupter must break 26 kA and withstand 60 kV during the energy transfer time of 700 μs. Testing in progress already has shown successful interruption using single vacuum interrupters up to 31 kA and 66 kV

6-7 Mev Characteristic Gamma-Ray Source Using A Plasma Opening Switch And A Marx Bank

Science.gov (United States)

2011-06-01

of Hawk, including the POS, is shown in Fig. 2a. The POS consists of 12 plasma guns made from coaxial cables that inject ionized plasma radially...inward between two coaxial conductors prior to firing the generator. The POS plasma conducts the generator current as a short circuit for about 700...vacuum gap in the plasma . High-energy electron- and ion-beams form in the plasma -filled coaxial region, with ions from the plasma and the polyethylene

Plasma-pulse formation and acceleration for fast high-power technology and switching applications

International Nuclear Information System (INIS)

Doucet, H.J.; Jones, W.D.; Moustaizis, S.; Lamain, H.; Rouille, C.

1985-01-01

A carbon plasma gun powered by a low-inductance capacitor bank and transmission line is used to produce μsec-length pulses of protons having densities of 10/sup 12/-10/sup 14/ cm/sup -3/ at distances of 0.3-1.5 m from the gun and velocities of 10-20 cm/μs. Essential features are a low-inductance surface switch and a nonlinear transmission grid

Plasma-filled diode experiments on PBFA-II

International Nuclear Information System (INIS)

Renk, T.J.; Rochau, G.E.; McDaniel, D.H.; Moore, W.B.; Zuchowski, N.; Padilla, R.

1987-01-01

The PBFA-II accelerator is designed to use a Plasma Opening Switch (POS) for pulse shaping and voltage multiplication using inductive storage. The vacuum section of the machine consists of a set of short magnetically insulated transmission lines (MITLs) that both act as a voltage adder for series stacking of the pulses out of the 72 parallel plate water lines, and as a 100 nH (total) storage inductor upstream of a biconically shaped POS region. There are two POS plasma injection areas, located above and below an equatorial load, which has consisted of either a short circuit, a blade (electron beam) diode, or an Applied B magnetically insulated ion diode. The POS is designed to conduct up to 6 MA, and open into a 5 ohm diode load in 10 ns or less. Under these conditions, the voltage at the load is predicted to exceed 24 MV. Initial POS experiments using these loads have produced 1) opening times of typically 20 ns or longer, 2) poor current transfer efficiency (less than 50%) when load impedances averaged 2 ohms or more, and 3) differential switch opening in azimuthal segments of the power feed, thought to be caused by poor plasma uniformity across the flashboard plasma source. One possible explanation for 2) is that efficient transfer out of the POS requires that the current carried to the load be magnetically insulated, or else considerable energy will be deposited in the feed region between the POS and load. This had indeed been observed. The problem is further exacerbated by the longer current turn-on times that occur when an ion diode is used as the load

Laboratory of plasma studies. Papers on high power particle beams

International Nuclear Information System (INIS)

Anon.

1990-01-01

This book contains paper on Exploding metal film active anode sources experiments on the Lion extractor Ion Diode; Long conductor time plasma opening switch experiments; and Focusing studies of an applied B r extraction diode on the Lion accelerator

Recent progress in Open Data production and consumption - examples from a Governmental institute (SMHI) and a collaborative EU research project (SWITCH-ON)

Science.gov (United States)

Arheimer, Berit; Falkenroth, Esa

2014-05-01

The Swedish Meteorological and Hydrological Institute (SMHI) has a long tradition both in producing and consuming open data on a national, European and global scale. It is also promoting community building among water scientists in Europe by participating in and initiating collaborative projects. This presentation will exemplify the contemporary European movement imposed by the INSPIRE directive and the Open Data Strategy, by showing the progress in openness and shift in attitudes during the last decade when handling Research Data and Public Sector Information at a national European institute. Moreover, the presentation will inform about a recently started collaborative project (EU FP7 project No 603587) coordinated by SMHI and called SWITCH-ON http://water-switch-on.eu/. The project addresses water concerns and currently untapped potential of open data for improved water management across the EU. The overall goal of the project is to make use of open data, and add value to society by repurposing and refining data from various sources. SWITCH-ON will establish new forms of water research and facilitate the development of new products and services based on principles of sharing and community building in the water society. The SWITCH-ON objectives are to use open data for implementing: 1) an innovative spatial information platform with open data tailored for direct water assessments, 2) an entirely new form of collaborative research for water-related sciences, 3) fourteen new operational products and services dedicated to appointed end-users, 4) new business and knowledge to inform individual and collective decisions in line with the Europe's smart growth and environmental objectives. The presentation will discuss challenges, progress and opportunities with the open data strategy, based on the experiences from working both at a Governmental institute and being part of the global research community.

Open-loop correction for an eddy current dominated beam-switching magnet.

Science.gov (United States)

Koseki, K; Nakayama, H; Tawada, M

2014-04-01

A beam-switching magnet and the pulsed power supply it requires have been developed for the Japan Proton Accelerator Research Complex. To switch bunched proton beams, the dipole magnetic field must reach its maximum value within 40 ms. In addition, the field flatness should be less than 5 × 10(-4) to guide each bunched beam to the designed orbit. From a magnetic field measurement by using a long search coil, it was found that an eddy current in the thick endplates and laminated core disturbs the rise of the magnetic field. The eddy current also deteriorates the field flatness over the required flat-top period. The measured field flatness was 5 × 10(-3). By using a double-exponential equation to approximate the measured magnetic field, a compensation pattern for the eddy current was calculated. The integrated magnetic field was measured while using the newly developed open-loop compensation system. A field flatness of less than 5 × 10(-4), which is an acceptable value, was achieved.

On the evolution of jet energy and opening angle in strongly coupled plasma

International Nuclear Information System (INIS)

Chesler, Paul M.; Rajagopal, Krishna

2016-01-01

We calculate how the energy and the opening angle of jets in N=4 SYM theory evolve as they propagate through the strongly coupled plasma of that theory. We define the rate of energy loss dE_j_e_t/dx and the jet opening angle in a straightforward fashion directly in the gauge theory before calculating both holographically, in the dual gravitational description. In this way, we rederive the previously known result for dE_j_e_t/dx without the need to introduce a finite slab of plasma. We obtain a striking relationship between the initial opening angle of the jet, which is to say the opening angle that it would have had if it had found itself in vacuum instead of in plasma, and the thermalization distance of the jet. Via this relationship, we show that N=4 SYM jets with any initial energy that have the same initial opening angle and the same trajectory through the plasma experience the same fractional energy loss. We also provide an expansion that describes how the opening angle of the N=4 SYM jets increases slowly as they lose energy, over the fraction of their lifetime when their fractional energy loss is not yet large. We close by looking ahead toward potential qualitative lessons from our results for QCD jets produced in heavy collisions and propagating through quark-gluon plasma.

The 26th IEEE international conference on plasma science

International Nuclear Information System (INIS)

1999-01-01

Some of the sessions covered by this conference are: Basic Processes in Fully and Partially Ionized Plasmas; Slow Wave Devices; Laser-Produced Plasma; Non-Equilibrium Plasma Processing; Space Plasmas and Partially Ionized Gases; Microwave Plasmas; Inertial Confinement Fusion; Plasma Diagnostics; Computational Plasma Physics; Microwave Systems; Laser Produced Plasmas and Dense Plasma Focus; Intense Electron and Ion Beams; Fast Wave Devices; Spherical Configurations and Ball Lightning; Thermal Plasma Chemistry and Processing and Environmental Issues in Plasma Science; Plasma, Ion, and Electron Sources; Fast Wave Devices and Intense Beams; Fast Z-pinches and X-ray Lasers; Plasma Opening Switches; Plasma for Lighting; Intense Beams; Vacuum Microwaves; Magnetic Fusion Energy; and Plasma Thrusters and Arcs. Separate abstracts were prepared for some of the papers in this volume

Plasma X-ray sources powered by megajoule magnetocumulative generators

Energy Technology Data Exchange (ETDEWEB)

Popkov, N F; Averchenkov, V Ya; Pikar` , A S; Ryaslov, E A; Kargin, V I; Lazarev, S A; Borodkov, V V; Nazarenko, S T; Makartsev, G F [All-Russian Research Inst. of Experimental Physics, Sarov (Russian Federation). Russian Federal Nuclear Center

1997-12-31

Experiments using magnetocumulative generators (MCGs) were performed to power three different types of high-energy-density plasma discharges suitable for intense x-ray generation. These included the H-pressed discharge, the capillary z-pinch, and the {theta}-pinch. The MCGs were operated both with and without plasma opening switches. The characteristic currents were approximately 10 MA and characteristic time scales approximately 1 {mu}s. (author). 7 figs., 3 refs.

Plasma behaviors in the open field region of reversed-field theta-pinch

International Nuclear Information System (INIS)

Aso, Yoshiyuki; Hirano, Keiichi.

1983-03-01

A characteristic behavior of the plasma in an open field region of reversed field theta pinch has been studied with the guide field (GF) which extends the field line along the axial direction. The experimental result suggests that the rotaional instability may be induced in FRC after the plasma touches the wall at the ends of the open field. (author)

An open-closed-loop iterative learning control approach for nonlinear switched systems with application to freeway traffic control

Science.gov (United States)

Sun, Shu-Ting; Li, Xiao-Dong; Zhong, Ren-Xin

2017-10-01

For nonlinear switched discrete-time systems with input constraints, this paper presents an open-closed-loop iterative learning control (ILC) approach, which includes a feedforward ILC part and a feedback control part. Under a given switching rule, the mathematical induction is used to prove the convergence of ILC tracking error in each subsystem. It is demonstrated that the convergence of ILC tracking error is dependent on the feedforward control gain, but the feedback control can speed up the convergence process of ILC by a suitable selection of feedback control gain. A switched freeway traffic system is used to illustrate the effectiveness of the proposed ILC law.

OpenFlow Switching Performance using Network Simulator - 3

OpenAIRE

Sriram Prashanth, Naguru

2016-01-01

Context. In the present network inventive world, there is a quick expansion of switches and protocols, which are used to cope up with the increase in customer requirement in the networking. With increasing demand for higher bandwidths and lower latency and to meet these requirements new network paths are introduced. To reduce network load in present switching network, development of new innovative switching is required. These required results can be achieved by Software Define Network or Trad...

Transient-Switch-Signal Suppressor

Science.gov (United States)

Bozeman, Richard J., Jr.

1995-01-01

Circuit delays transmission of switch-opening or switch-closing signal until after preset suppression time. Used to prevent transmission of undesired momentary switch signal. Basic mode of operation simple. Beginning of switch signal initiates timing sequence. If switch signal persists after preset suppression time, circuit transmits switch signal to external circuitry. If switch signal no longer present after suppression time, switch signal deemed transient, and circuit does not pass signal on to external circuitry, as though no transient switch signal. Suppression time preset at value large enough to allow for damping of underlying pressure wave or other mechanical transient.

Confinement of plasma along shaped open magnetic fields from the centrifugal force of supersonic plasma rotation.

Science.gov (United States)

Teodorescu, C; Young, W C; Swan, G W S; Ellis, R F; Hassam, A B; Romero-Talamas, C A

2010-08-20

Interferometric density measurements in plasmas rotating in shaped, open magnetic fields demonstrate strong confinement of plasma parallel to the magnetic field, with density drops of more than a factor of 10. Taken together with spectroscopic measurements of supersonic E × B rotation of sonic Mach 2, these measurements are in agreement with ideal MHD theory which predicts large parallel pressure drops balanced by centrifugal forces in supersonically rotating plasmas.

Study of the switching rate of gas-discharge devices based on the open discharge with counter-propagating electron beams

International Nuclear Information System (INIS)

Bokhan, P. A.; Gugin, P. P.; Lavrukhin, M. A.; Zakrevsky, Dm. E.

2015-01-01

The switching rate of gas-discharge devices “kivotrons” based on the open discharge with counter-propagating electron beams has been experimentally studied. Structures with 2-cm 2 overall cathode area were examined. The switching time was found to show a monotonic decrease with increasing the working-gas helium pressure and with increasing the voltage across the discharge gap at breakdown. The minimum switching time was found to be ∼240 ps at 17 kV voltage, and the maximum rate of electric-current rise limited by the discharge-circuit inductance was 3 × 10 12  A/s

A column switching ultrahigh-performance liquid chromatography-tandem mass spectrometry method to determine anandamide and 2-arachidonoylglycerol in plasma samples.

Science.gov (United States)

Marchioni, Camila; de Souza, Israel Donizeti; Grecco, Caroline Fernandes; Crippa, José Alexandre; Tumas, Vitor; Queiroz, Maria Eugênia Costa

2017-05-01

This study reports a fast, sensitive, and selective column switching ultrahigh-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) method to determine the endocannabinoids (eCBs), anandamide (AEA), and 2-arachidonoylglycerol (2-AG) in plasma samples. This bidimensional system used a restricted access media column (RP-8 ADS, 25 mm × 4 mm × 25 μM) in the first dimension and a core-shell Kinetex C18 (100 mm × 2, 1.7 mm × 1 μM) column in the second dimension, followed by detection in a mass spectrometer triple quadrupole (multiple reactions monitoring mode) operating in the positive mode. RP-8 ADS was used for trace enrichment of eCBs (reverse phase partitioning) and macromolecular matrix size exclusion; the core-shell column was used for the chromatographic separation. The column switching UHPLC-MS/MS method presented a linear range spanning from 0.1 ng mL -1 (LOQ) to 6 ng mL -1 for AEA and from 0.04 ng mL -1 (LOQ) to 10 ng mL -1 for 2-AG. Excluding the LLOQ values, the precision assays provided coefficients of variation lower than 8% and accuracy with relative standard error values lower than 14%. Neither carryover nor matrix effects were detected. This high-throughput column switching method compared to conventional methods is time saving as it involves fewer steps, consumes less solvent, and presents lower LLOQ. The column switching UHPLC-MS/MS method was successfully applied to determine AEA and 2-AG in plasma samples obtained from Alzheimer's disease patients. Graphical abstract A column switching ultra high-performance liquid chromatography-tandem mass spectrometry method using RP-8 ADS column and core shell column to determine endocannabinoids in plasma samples.

Open-Circuit End Effect of Microstrip Line Configuration in Plasma Medium

Directory of Open Access Journals (Sweden)

Prem Bhushan Mital

1996-01-01

Full Text Available The extension in length for open microstrip configuration in plasma media is determined using spectral domain technique under quasi static approach [1, 2]. The results were verified by modifying Hammerstad equation for plasma media. Good agreement is found between the two results.

Two-dimensional modeling of x-ray output from switched foil implosions on Procyon

Science.gov (United States)

Bowers, R. L.; Nakafuji, G.; Greene, A. E.; McLenithan, K. D.; Peterson, D. L.; Roderick, N. F.

1996-09-01

A series of two-dimensional radiation magnetohydrodynamic calculations are presented of a Z-pinch implosion using a plasma flow switch. Results from a recent experiment using the high explosive driven generator Procyon, which delivered 16.5 MA to a plasma flow switch and switched about 15 MA into a static load, are used to study the implosion of a 29 mg load foil [J. H. Goforth et al., ``Review of the Procyon Explosive Pulsed Power System,'' in Ninth IEEE Pulsed Power Conference, June 1993, Albuquerque, edited by K. R. Prestwich and W. L. Baker (Institute of Electrical and Electronics Engineers, Piscataway, NJ, 1993), p. 36]. The interaction of the switch with the load plasma and the effects of background plasma on the total radiation output is examined. Models which assume ideal switching are also included. Also included are the effects of perturbations in the load plasma which may be associated with initial vaporization of the load foil. If the background plasma density in the switch region and in the load region does not affect the dynamics, the pinch is predicted to produce a total radiation output of about 4 MJ. Including perturbations of the load plasma associated with switching and assuming a background plasma density after switching in excess of 10-7 g/cm3 results in a total output from the pinch of about 0.6 MJ.

Beam-plasma interaction in case of injection of the electron beam to the symmetrically open plasma system

International Nuclear Information System (INIS)

Opanasenko, A.V.; Romanyuk, L.I.

1992-01-01

A beam-plasma interaction at the entrance of the symmetrically open plasma system with an electron beam injected through it is investigated. An ignition of the plasma-beam discharge on waves of upper hybrid dispersion branch of a magnetoactive plasma is found in the plasma penetrating into the vacuum contrary to the beam. It is shown that the beam-plasma discharge is localized in the inhomogeneous penetrating plasma in the zone where only these waves exist. Regularities of the beam-plasma discharge ignition and manifestation are described. It is determined that the electron beam crossing the discharge zone leads to the strong energy relaxation of the beam. It is shown possible to control the beam-plasma discharge ignition by changing the potential of the electron beam collector. (author)

Current delivery and radiation yield in plasma flow switch-driven implosions

International Nuclear Information System (INIS)

Baker, W.L.; Degnan, J.H.; Beason, J.D.

1995-01-01

Vacuum inductive-store, plasma flow switch-driven implosion experiments have been performed using the Shiva Star capacitor bank (1300 μf, 3 nH, 120 kV, 9.4 MJ). A coaxial plasma gun arrangement is employed to store magnetic energy in the vacuum volume upstream of a dynamic discharge during the 3- to 4-μs rise of current from the capacitor bank. Motion of the discharge off the end of the inner conductor of the gun releases this energy to implode a coaxial cylindrical foil. The implosion loads are 5-cm-radius, 2-cm-long, 200 to 400 μg/cm 2 cylinders of aluminum or aluminized Formvar. With 5 MJ stored initially in the capacitor bank, more than 9 MA are delivered to the implosion load with a rise time of nearly 200 ns. The subsequent implosion results in a radiation output of 0.95 MJ at a power exceeding 5 TW (assuming isotropic emission). Experimental results and related two-dimensional magnetohydrodynamic simulations are discussed. 10 refs., 12 figs

Phosphorylation of plasma membrane aquaporin regulates temperature-dependent opening of tulip petals.

Science.gov (United States)

Azad, Abul Kalam; Sawa, Yoshihiro; Ishikawa, Takahiro; Shibata, Hitoshi

2004-05-01

The opening and closing of tulip petals was reproduced in the dark by changing the temperature from 5 degrees C to 20 degrees C for opening and 20 degrees C to 5 degrees C for closing. The opening process was accompanied by (3)H(2)O transport through the stem from the incubation medium to the petals. A Ca(2+)-channel blocker and a Ca(2+)-chelator inhibited petal opening and (3)H(2)O transport. Several proteins in the isolated plasma membrane fraction were phosphorylated in the presence of 25 micro M Ca(2+) at 20 degrees C. The 31-kDa protein that was phosphorylated, was suggested immunologically as the putative plasma membrane aquaporin (PM-AQP). This phosphorylated PM-AQP clearly reacted with the anti-phospho-Ser. In-gel assay revealed the presence of a 45-kDa Ca(2+)-dependent protein kinase in the isolated plasma membrane. Phosphorylation of the putative PM-AQP was thought to activate the water channel composed of PM-AQP. Dephosphorylation of the phosphorylated PM-AQP was also observed during petal closing at 5 degrees C, suggesting the inactivation of the water channel.

Characterization of cable gun plasma with a charge collector array

International Nuclear Information System (INIS)

Chen Yulan; Zeng Zhengzhong; Sun Fengju; Kuai Bin; Qiu Aici; Yin Jiahui; Cong Peitian; Liang Tianxue

2003-01-01

The density, drift velocity and reproducibility of the plasma produced by a cable plasma gun array have been measured with a charge collector array. The plasma is used to prefill a coaxial plasma-opening switch with a conducting time approaching 0.4 μs. The reproducibility of the plasma source in subsequent shots is better than 5%. Near the gun nozzle and the opposite electrode, the plasma density amounts to 10 15 cm -3 , which is 2 times to 3 times that in the gap between the two coaxial electrodes. A plasma drift velocity of about 2.4 cm/μs is observed from the time of flight of the charged particles. Both plasma density and drift velocity increase almost linearly with the rise in charge voltage

Mega-Amp Opening Switch with Nested Electrodes/Pulsed Generator of Ion and Ion Cluster Beams.

Science.gov (United States)

1985-07-01

i.e., noncollisiona].) resistivity which controls the "~switch opening" function (specifically, the rate of disintergration of the PF pinch where...unaffected the pinch field Be and then disassemble in a light (D) component and other heavy components. Production and propagation of-neutrals (from...emission, production and - evaporation would imply a distorsion of the pinholeimage-because of B -which is not p.-.. observed (our pinhole resolution is 150

Diagnostics for Pioneer I imploding plasma experiments

International Nuclear Information System (INIS)

Lee, P.H.Y.; Benjamin, R.F.; Brownell, J.H.

1985-01-01

The Pioneer I series of imploding plasma experiments are aimed at collapsing a thin aluminum foil with a multimegampere, submicrosecond electrical pulse produced by an explosive flux compression generator and fast plasma compression opening switch. Anticipated experimental conditions are bounded by implosion velocities of 2 x 10 7 cm/s and maximum plasma temperatures of 100 eV. A comprehensive array of diagnostics have been deployed to measure implosion symmetry (gated microchannel plate array and other time-resolved imaging), temperature of the imploding plasma (visible/uv spectroscopy), stagnation geometry (x-ray pinhole imaging), radiation emission characteristics at pinch (XRD's, fast bolometry), and electrical drive history (Rogowski loops, Faraday rotation current detectors, and capacitive voltage probes). Diagnostic performance is discussed and preliminary results are presented

Coupling between feedback loops in autoregulatory networks affects bistability range, open-loop gain and switching times

International Nuclear Information System (INIS)

Tiwari, Abhinav; Igoshin, Oleg A

2012-01-01

Biochemical regulatory networks governing diverse cellular processes such as stress-response, differentiation and cell cycle often contain coupled feedback loops. We aim at understanding how features of feedback architecture, such as the number of loops, the sign of the loops and the type of their coupling, affect network dynamical performance. Specifically, we investigate how bistability range, maximum open-loop gain and switching times of a network with transcriptional positive feedback are affected by additive or multiplicative coupling with another positive- or negative-feedback loop. We show that a network's bistability range is positively correlated with its maximum open-loop gain and that both quantities depend on the sign of the feedback loops and the type of feedback coupling. Moreover, we find that the addition of positive feedback could decrease the bistability range if we control the basal level in the signal-response curves of the two systems. Furthermore, the addition of negative feedback has the capacity to increase the bistability range if its dissociation constant is much lower than that of the positive feedback. We also find that the addition of a positive feedback to a bistable network increases the robustness of its bistability range, whereas the addition of a negative feedback decreases it. Finally, we show that the switching time for a transition from a high to a low steady state increases with the effective fold change in gene regulation. In summary, we show that the effect of coupled feedback loops on the bistability range and switching times depends on the underlying mechanistic details. (paper)

High-Power Plasma Switch for 11.4 GHz Microwave Pulse Compressor

International Nuclear Information System (INIS)

Hirshfield, Jay L.

2010-01-01

Results obtained in several experiments on active RF pulse compression at X-band using a magnicon as the high-power RF source are presented. In these experiments, microwave energy was stored in high-Q TE01 and TE02 modes of two parallel-fed resonators, and then discharged using switches activated with rapidly fired plasma discharge tubes. Designs and high-power tests of several versions of the compressor are described. In these experiments, coherent pulse superposition was demonstrated at a 5-9 MW level of incident power. The compressed pulses observed had powers of 50-70 MW and durations of 40-70 ns. Peak power gains were measured to be in the range of 7:1-11:1 with efficiency in the range of 50-63%.

Large aperture optical switching devices

International Nuclear Information System (INIS)

Goldhar, J.; Henesian, M.A.

1983-01-01

We have developed a new approach to constructing large aperture optical switches for next generation inertial confinement fusion lasers. A transparent plasma electrode formed in low pressure ionized gas acts as a conductive coating to allow the uniform charging of the optical faces of an electro-optic material. In this manner large electric fields can be applied longitudinally to large aperture, high aspect ratio Pockels cells. We propose a four-electrode geometry to create the necessary high conductivity plasma sheets, and have demonstrated fast (less than 10 nsec) switching in a 5x5 cm aperture KD*P Pockels cell with such a design. Detaid modelling of Pockels cell performance with plasma electrodes has been carried out for 15 and 30 cm aperture designs

Switched-based interference reduction scheme for open-access overlaid cellular networks

KAUST Repository

Radaydeh, Redha Mahmoud Mesleh

2012-06-01

Femtocells have been proposed to enhance the spatial coverage and system capacity of existing cellular networks. However, this technology may result in significant performance loss due to the increase in co-channel interference, particularly when coordination between access points is infeasible. This paper targets interference management in such overlaid networks. It is assumed that the femtocells employ the open-access strategy to reduce cross-tier interference, and can share resources concurrently. It is also assumed that each end user (EU) can access one channel at a time, and transfer limited feedback. To reduce the effect of co-tier interference in the absence of the desired EU channel state information (CSI) at the serving access point as well as coordination between active access points, a switched scheme based on the interference levels associated with available channels is proposed. Through the analysis, the scheme modes of operation in under-loaded and over-loaded channels are studied, from which the statistics of the resulting interference power are quantified. The impact of the proposed scheme on the received desired power is thoroughly discussed. In addition, the effect of the switching threshold on the achieved performance of the desired EU is investigated. The results clarify that the proposed scheme can improve the performance while reducing the number of examined channels and feedback load. © 2012 IEEE.

Uji Performa Software-based Openflow Switch Berbasis Openwrt

OpenAIRE

Kartadie, Rikie; Suryanto, Tommy

2015-01-01

Perkembangan pesat Software-Defined Network telah dirasakan oleh vendor vendor besar. HP, Google dan IBM, mulai merubah pola routing-switching pada network mereka dari pola routingswitching tradisional ke pola infrastruktur routing-switching Software-defined Network. Untuk melakukan eksperimen tentang OpenFlow, para peneliti sering kali harus menggunakan perangkat hardware/dedicated switch OpenFlow yang dikeluarkan oleh beberapa vendor dengan harga yang tinggi. Kenyataannya, software-based sw...

Green's function for a switched plasma medium and a perturbation technique for the study of wave propagation in a transient plasma with a small rise time

International Nuclear Information System (INIS)

Kalluri, D.K.

1996-01-01

The main effect of switching a medium (creating a temporal discontinuity in the properties of a medium) is the splitting of the source (incident) wave into new waves whose frequencies are different. Lightning induced effects in the ionosphere cause a temporary enhancement of ionization. Such transient plasmas have a time-varying plasma frequency ω p (t) with a rise time T r . If the period t 0 of a source wave existing before the transient effect begins is much larger than the rise time, the ionization change may be idealized as a sudden switching of the medium. The solution to this initial value problem with a step-change in the electron density profile is known and this profile will be considered as a reference profile. The topic of this paper is the solution of the initial value problem when t 0 is comparable to the rise time T r . The initial motivation for investigating the problem is given below. There is considerable interest in the ionospheric physics community to investigate the recently discovered Sprites phenomenon which are red emissions in the lower D region induced by the lightning discharges from a cloud to the ground. The preliminary indications are that the Sprite is a plasma with electron density enhanced by about 10 1 to 10 3 /cc in a rise time of about 100 micros

Building SDN-Based Agricultural Vehicular Sensor Networks Based on Extended Open vSwitch.

Science.gov (United States)

Huang, Tao; Yan, Siyu; Yang, Fan; Pan, Tian; Liu, Jiang

2016-01-19

Software-defined vehicular sensor networks in agriculture, such as autonomous vehicle navigation based on wireless multi-sensor networks, can lead to more efficient precision agriculture. In SDN-based vehicle sensor networks, the data plane is simplified and becomes more efficient by introducing a centralized controller. However, in a wireless environment, the main controller node may leave the sensor network due to the dynamic topology change or the unstable wireless signal, leaving the rest of network devices without control, e.g., a sensor node as a switch may forward packets according to stale rules until the controller updates the flow table entries. To solve this problem, this paper proposes a novel SDN-based vehicular sensor networks architecture which can minimize the performance penalty of controller connection loss. We achieve this by designing a connection state detection and self-learning mechanism. We build prototypes based on extended Open vSwitch and Ryu. The experimental results show that the recovery time from controller connection loss is under 100 ms and it keeps rule updating in real time with a stable throughput. This architecture enhances the survivability and stability of SDN-based vehicular sensor networks in precision agriculture.

Building SDN-Based Agricultural Vehicular Sensor Networks Based on Extended Open vSwitch

Directory of Open Access Journals (Sweden)

Tao Huang

2016-01-01

Full Text Available Software-defined vehicular sensor networks in agriculture, such as autonomous vehicle navigation based on wireless multi-sensor networks, can lead to more efficient precision agriculture. In SDN-based vehicle sensor networks, the data plane is simplified and becomes more efficient by introducing a centralized controller. However, in a wireless environment, the main controller node may leave the sensor network due to the dynamic topology change or the unstable wireless signal, leaving the rest of network devices without control, e.g., a sensor node as a switch may forward packets according to stale rules until the controller updates the flow table entries. To solve this problem, this paper proposes a novel SDN-based vehicular sensor networks architecture which can minimize the performance penalty of controller connection loss. We achieve this by designing a connection state detection and self-learning mechanism. We build prototypes based on extended Open vSwitch and Ryu. The experimental results show that the recovery time from controller connection loss is under 100 ms and it keeps rule updating in real time with a stable throughput. This architecture enhances the survivability and stability of SDN-based vehicular sensor networks in precision agriculture.

Building SDN-Based Agricultural Vehicular Sensor Networks Based on Extended Open vSwitch

Science.gov (United States)

Huang, Tao; Yan, Siyu; Yang, Fan; Pan, Tian; Liu, Jiang

2016-01-01

Software-defined vehicular sensor networks in agriculture, such as autonomous vehicle navigation based on wireless multi-sensor networks, can lead to more efficient precision agriculture. In SDN-based vehicle sensor networks, the data plane is simplified and becomes more efficient by introducing a centralized controller. However, in a wireless environment, the main controller node may leave the sensor network due to the dynamic topology change or the unstable wireless signal, leaving the rest of network devices without control, e.g., a sensor node as a switch may forward packets according to stale rules until the controller updates the flow table entries. To solve this problem, this paper proposes a novel SDN-based vehicular sensor networks architecture which can minimize the performance penalty of controller connection loss. We achieve this by designing a connection state detection and self-learning mechanism. We build prototypes based on extended Open vSwitch and Ryu. The experimental results show that the recovery time from controller connection loss is under 100 ms and it keeps rule updating in real time with a stable throughput. This architecture enhances the survivability and stability of SDN-based vehicular sensor networks in precision agriculture. PMID:26797616

Software Switching for Data Acquisition

CERN Multimedia

CERN. Geneva; Malone, David

2016-01-01

In this talk we discuss the feasibility of replacing telecom-class routers with a topology of commodity servers acting as software switches in data acquisition. We extend the popular software switch, Open vSwitch, with a dedicated, throughput-oriented buffering mechanism. We compare the performance under heavy many-to-one congestion to typical Ethernet switches and evaluate the scalability when building larger topologies, exploiting the integration with software-defined networking technologies. Please note that David Malone will speak on behalf of Grzegorz Jereczek.

Bipolar resistive switching characteristics of low temperature grown ZnO thin films by plasma-enhanced atomic layer deposition

International Nuclear Information System (INIS)

Zhang Jian; Yang Hui; Zhang Qilong; Dong Shurong; Luo, J. K.

2013-01-01

ZnO films deposited by plasma-enhanced atomic layer deposition (PEALD) have been used to investigate resistive memory behavior. The bipolar resistance switching properties were observed in the Al/PEALD-ZnO/Pt devices. The resistance ratio for the high and low resistance states (HRS/LRS) is more than 10 3 , better than ZnO devices deposited by other methods. The dominant conduction mechanisms of HRS and LRS are trap-controlled space charge limited current and Ohmic behavior, respectively. The resistive switching behavior is induced upon the formation/disruption of conducting filaments. This study demonstrated that the PEALD-ZnO films have better properties for the application in 3D resistance random access memory.

Performance Test of Openflow Agent on Openflow Software-Based Mikrotik RB750 Switch

Directory of Open Access Journals (Sweden)

Rikie Kartadie

2016-11-01

Full Text Available A network is usually developed by several devices such as router, switch etc. Every device forwards data package manipulation with complicated protocol planted in its hardware. An operator is responsible for running configuration either to manage rules or application applied in the network. Human error may occur when device configuration run manually by operator. Some famous vendors, one of them is MikroTik, has also been implementing this OpenFlow on its operation. It provides the implementation of SDN/OpenFlow architecture with affordable cost. The second phase research result showed that switch OF software-based MikroTik resulted higher latency value than both mininet and switch OF software-based OpenWRT. The average gap value of switch OF software-based MikroTik is 2012 kbps lower than the value of switch OF software-based OpenWRT. The average gap value of throughput bandwidth protocol UDP switch OF software-based MikroTik is 3.6176 kBps lower than switch OF software-based OpenWRT and it is 8.68 kBps lower than mininet. The average gap throughput jitter protokol UDP of switch OF software-based MiktoTik is 0.0103ms lower than switch OF software-based OpenWRT and 0.0093ms lower than mininet. 

First results on dense plasma confinement at the multimirror open trap GOL-3-II

International Nuclear Information System (INIS)

Koidan, V.S.; Arzhannikov, A.V.; Astrelin, V.T.

2001-01-01

First results of experiments on plasma confinement in multimirror open trap GOL-3-II are presented. This facility is an open trap with total length of 17 m intended for confinement of a relatively dense (10 15 -10 17 cm -3 ) plasma in axially-symmetrical magnetic system. The plasma heating is provided by a high-power electron beam (1 MeV, 30 kA, 8 ms, 200 kJ). New phase of the experiments is aimed to confinement of high-β thermalized plasma. Two essential modifications of the facility have been done. First, plasma column was separated by vacuum sections from the beam accelerator and exit beam receiver. Second, the magnetic field on part of the solenoid was reconfigured into multimirror system with H max /H min ∼1.5 and 22 cm cell length. Results of the experiments at modified configuration of the device indicate that the confinement time of the plasma with n e ∼(0, 5/5)·10 15 cm -3 and T e ∼1 keV increases more than order of magnitude. (author)

X-ray radiation source based on a plasma filled diode

Energy Technology Data Exchange (ETDEWEB)

Popkov, N F; Kargin, V I; Ryaslov, E A; Pikar, A S [All-Russian Research Inst. of Experimental Physics, Sarov (Russian Federation). Russian Federal Nuclear Center

1997-12-31

The results are given of studies on a plasma X-ray source providing 2.5 krad of radiation dose per pulse over an area of 100 cm{sup 2} in the quantum energy range between 20 and 500 keV. The pulse duration was 100 ns. The spectral radiation distribution was obtained under various operating conditions of plasma and diode. A Marx generator served as the starting power source of 120 kJ with a discharge time of T/4=10{sup -6} s. A short electromagnetic pulse (10{sup -7} s) was shaped using plasma erosion opening switches. (author). 5 figs., 4 refs.

Suppression of fast electron leakage from large openings in a plasma neutralizer for N-NB systems

International Nuclear Information System (INIS)

Kashiwagi, Mieko; Hanada, Masaya; Yamana, Takashi; Inoue, Takashi; Imai, Tsuyoshi; Taniguchi, Masaki; Watanabe, Kazuhiro

2006-01-01

To produce highly ionized plasmas at low operating pressure in a plasma neutralizer of negative ion based neutral beam (N-NB) systems, it is a critical issue to suppress leakage of fast electrons through large openings as the beam entrance/exit. The authors propose to form weak transverse magnetic fields without a significant beam deflection, called the shield field, across the large openings of the neutralizer. A numerical study showed that the shield field of only few tens of Gauss is sufficient to suppress the fast electron leakage from the openings. By measuring of an electron energy distribution function (EEDF), it was confirmed that such a weak magnetic field is enough to repel the fast electrons back into the neutralizer plasma. As the result, the plasma density increased with the shield field strength and saturated at 30 G. The plasma density reached 50% higher value than that without the shield field. Thus it was found that reflected fast electrons by the shield field of only 30 G work effectively for the plasma generation. It was also estimated that such a weak magnetic field sufficiently suppresses the deflection of a 1 MeV beam. This weak magnetic field would be applicable to the plasma neutralizer for the fusion demonstration (DEMO) plant

Measurement of the open loop plasma equilibrium response in TCV

International Nuclear Information System (INIS)

Coutlis, A.; Bandyopadhyay, I.; Lister, J.B.; Vyas, P.; Albanese, R.; Limebeer, D.J.N.; Villone, F.; Wainwright, J.P.

1999-01-01

A new technique and results are presented for the estimation of the open loop frequency response of the plasma on TCV. Voltages were applied to poloidal field coils and the resulting plasma current, position and shape related parameters were measured. The results are compared with the CREATE-L model, and good agreement is confirmed. The results are a significant advance on previous comparisons with closed loop data, which were limited by the role of feedback in the system. A simpler circuit equation model has also been developed in order to understand the reasons for the good agreement and identify which plasma properties are important in determining the response. The reasons for the good agreement with this model are discussed. An alternative modelling method has been developed, combining features of both the theoretical and experimental techniques. Its advantage is that it incorporates well defined knowledge of the electromagnetic properties of the tokamak with experimental data to derive plasma related parameters. This new model provides further insight into the plasma behaviour. (author)

Characterisation of Plasma Filled Rod Pinch electron beam diode operation

Science.gov (United States)

MacDonald, James; Bland, Simon; Chittenden, Jeremy

2016-10-01

The plasma filled rod pinch diode (aka PFRP) offers a small radiographic spot size and a high brightness source. It operates in a very similar to plasma opening switches and dense plasma focus devices - with a plasma prefill, supplied via a number of simple coaxial plasma guns, being snowploughed along a thin rod cathode, before detaching at the end. The aim of this study is to model the PFRP and understand the factors that affect its performance, potentially improving future output. Given the dependence on the PFRP on the prefill, we are making detailed measurements of the density (1015-1018 cm-3), velocity, ionisation and temperature of the plasma emitted from a plasma gun/set of plasma guns. This will then be used to provide initial conditions to the Gorgon 3D MHD code, and the dynamics of the entire rod pinch process studied.

An Enhanced Three-Level Voltage Switching State Scheme for Direct Torque Controlled Open End Winding Induction Motor

Science.gov (United States)

Kunisetti, V. Praveen Kumar; Thippiripati, Vinay Kumar

2018-01-01

Open End Winding Induction Motors (OEWIM) are popular for electric vehicles, ship propulsion applications due to less DC link voltage. Electric vehicles, ship propulsions require ripple free torque. In this article, an enhanced three-level voltage switching state scheme for direct torque controlled OEWIM drive is implemented to reduce torque and flux ripples. The limitations of conventional Direct Torque Control (DTC) are: possible problems during low speeds and starting, it operates with variable switching frequency due to hysteresis controllers and produces higher torque and flux ripple. The proposed DTC scheme can abate the problems of conventional DTC with an enhanced voltage switching state scheme. The three-level inversion was obtained by operating inverters with equal DC-link voltages and it produces 18 voltage space vectors. These 18 vectors are divided into low and high frequencies of operation based on rotor speed. The hardware results prove the validity of proposed DTC scheme during steady-state and transients. From simulation and experimental results, proposed DTC scheme gives less torque and flux ripples on comparison to two-level DTC. The proposed DTC is implemented using dSPACE DS-1104 control board interface with MATLAB/SIMULINK-RTI model.

Plasma injection from the independent SHF-source in the open configuration 2. Magnetic fields of magnetic mirror configurations

International Nuclear Information System (INIS)

Beriya, Z.R.; Gogashvili, G.E.; Nanobashvili, S.I.

1992-01-01

The investigation was aimed at studying the characteristics and properties of plasma injected from independent stationary SHF source into an open magnetic trap of mirror geometry within a wide range of change in the experimental conditions. The investigations were primarily based on measurements of the distribution of charged particles in a plasma along the trap and on the dependence of the concentration on plasma production conditions in a SHF source. It is shown that the aggregate of the experimental data enables a conclusion that independent of SHF plasma can be succesfully used for filling on open magnetic trap of mirror configuration with plasma

Development of microsecond generators with plasma current interrupting switch in I.V. Kurchatov Institute of Atomic Energy. Frequency operation of generators

International Nuclear Information System (INIS)

Babykin, V.M.; Chikin, R.V.; Dolgachev, G.I.; Golovanov, Yu.P.; Kovalev, Yu.I.; Ushakov, A.G.; Zakatov, L.P.

1993-01-01

This paper is a follow up to previously published work on microsecond plasma current interrupting switches (PCIS), which has been conducted in the I.V. Kurchatov Inst. Here the authors present some information on the practical implementation of such devices, and provide an overview of new research facilities

The Aurora accelerator's triggered oil switch

International Nuclear Information System (INIS)

Weidenheimer, D.M.; Pereira, N.R.; Judy, D.C.; Stricklett, K.L.

1993-01-01

Achieving a radiation pulse with 15 ns risetime using all four of the Aurora accelerator's Blumlein pulse-forming lines demands synchronization of the Blumleins to within 10 ns (in addition to a 15 ns risetime for a single line). Timing of each Blumlein is controlled by a triggered 12 MV oil switch. A smaller-than-customary trigger electrode makes the switching time more reproducible. Time-resolved photography of the oil arcs suggests that triggering occurs simultaneously around the sharp edge of the trigger electrode, perhaps with small deviations that grow into the most prominent arcs characteristically seen in open-shutter photographs. However, many smaller arcs that are usually overlooked in open-shutter pictures may contribute to current conduction in a closed switch

Effect of switching to risperidone after unsuccessful treatment with aripiprazole on plasma monoamine metabolites level in the treatment of acute schizophrenia.

Science.gov (United States)

Miura, Itaru; Takeuchi, Satoshi; Katsumi, Akihiko; Kanno, Keiko; Watanabe, Kenya; Mashiko, Hirobumi; Niwa, Shin-Ichi

2012-09-01

In the treatment of acute schizophrenia, risperidone and aripiprazole are both placed the first line antipsychotics. These two antipsychotics have different pharmacological effects. We investigated the effects of risperidone on plasma levels of homovanillic acid (HVA) and 3-methoxy-4hydroxyphenylglycol after unsuccessful aripiprazole treatment in acute schizophrenia. Ten Japanese patients with acute schizophrenia were enrolled to this study. Plasma levels of monoamine metabolites were analyzed with high-performance liquid chromatography with electrochemical detection. Risperidone improved the symptoms and 4 of 10 patients were responders. Risperidone showed a tendency to decrease plasma HVA (pHVA) levels in responders (p = 0.068), but not in non-responders (p = 1.0). At baseline, pHVA levels of responders were significantly higher than that of non-responders (p = 0.033). A trend for negative correlation was found between pHVA at baseline and the changes in Positive and Negative Syndrome Scale-Total (p = 0.061, r = -0.61). Our results suggest that high pHVA level before switching may predict good response to the second line antipsychotics after unsuccessful first antipsychotic treatment. If aripiprazole is not effective in acute schizophrenia, switching to risperidone may be effective and reasonable strategy for improving symptoms. Copyright © 2012 John Wiley & Sons, Ltd.

R and D recommendations for future ERDA switch requirements

International Nuclear Information System (INIS)

Zucker, O.S.

1976-01-01

The following switches are briefly discussed: (1) high pressure and vacuum spark gaps, (2) liquid dielectric gaps, (3) solid dielectrics, (4) nonlinear ferromagnetic materials, (5) semiconductors, superconductors, (6) ferroelectric switches, (7) exploding wires, and (8) plasma instabilities

Creation of Principally New Generation of Switching Technique Elements (Reed Switches) with Nanostructured Contact Surfaces

Energy Technology Data Exchange (ETDEWEB)

Karabanov S M; Zeltser I A; Maizels R M; Moos E N; Arushanov K A, E-mail: zeltseria@rmcip.ru [Russia, Ryazan, 390027, Novaya Str., 51B, Ryazan Metal Ceramics Instrumentation Plant JSC (Russian Federation)

2011-04-01

The cycle of activities of the creation of principally new generation of reed switches with nanostructured contact surfaces was implemented. Experimental justification of the opportunity of reed switches creation with modified contact surface was given (instead of precious metals-based galvanic coating). Principally new technological process of modification of magnetically operated contacts contacting surfaces was developed, based on the usage of the ion-plasma methods of nanolayers and nanostructures forming having specified contact features.

IMPLEMENTATION OF A SWITCHED POWER SUPPLY FOR THE PLASMA ELECTROLYTIC OXIDATION TECHNIQUE

Directory of Open Access Journals (Sweden)

Fernando Gordillo-Delgado

2017-07-01

Full Text Available A switched-mode power supply was implemented for using in the Plasma Electrolytic Oxidation (PEO technique. The electronic devices are inexpensive and ordinarily used, which facilitates the construction of the system. A MICROCHIP microcontroller was used for generating a digital signal with frequency and duty cycle control; a capacitor bank and a diode bridge were also used for rectifying the input signal from the electrical network. The management of the output voltage was made with an arrangement of MOSFET transistors in the "low side" configuration; the measurement of the current was made with a Hall Effect sensor and using the USB communication the data was sent to a computer for visualization with a LabVIEW algorithm. The power supply was tested for creating microcavities in a titanium sheet with the aim of forming nanostructures of titanium dioxide.

Subnanosecond linear GaAs photoconductive switching, revision 1

Science.gov (United States)

Druce, R. L.; Pocha, M. D.; Griffin, K. L.; Hofer, W. W.

Research was conducted in photoconductive switching for the purpose of generating subnanosecond pulses in the 25 to 50kV range. The very fast recombination rates of Gallium Arsenide (GaAs) was exploited to explore the potential of GaAs as a closing and opening switch when operating in the linear mode (the linear mode is defined such that one carrier pair is generated for each photon absorbed). The closing time of a linear GaAs switch is theoretically limited by the characteristics of the laser pulse used to activate the switch (the carrier generation time in GaAs is (approx. 10(-14) sec) while the opening time is theoretically limited by the recombination time of the carriers. The recombination time is several ns for commercially available semi-insulating GaAs. Doping or neutron irradiation can reduce the recombination time to less than 100 ps. Switch closing times of less than 200 ps with a 100 ps duration laser pulse and opening times of less than 400 ps with neutron irradiated GaAs at fields of tens of kV/cm was observed. The illumination source was a Nd:YAG laser operating at 1.06 microns.

Electrochemical Switching of Conductance with Diarylethene-Based Redox-Active Polymers

DEFF Research Database (Denmark)

Logtenberg, Hella; van der Velde, Jasper H. M.; de Mendoza, Paula

2012-01-01

Reversible switching of conductance using redox triggered switching of a polymer-modified electrode is demonstrated. A bifunctional monomer comprising a central electroswitchable core and two bithiophene units enables formation of a film through anodic electropolymerization. The conductivity...... of the polymer can be switched electrochemically in a reversible manner by redox triggered opening and closing of the diarylethene unit. In the closed state, the conductivity of the modified electrode is higher than in the open state....

Experimental Results from a Laser-Triggered, Gas-Insulated, Spark-Gap Switch

Science.gov (United States)

Camacho, J. F.; Ruden, E. L.; Domonkos, M. T.

2017-10-01

We are performing experiments on a laser-triggered spark-gap switch with the goal of studying the transition from photoionization to current conduction. The discharge of current through the switch is triggered by a focused 532-nm wavelength beam from a Q-switched Nd:YAG laser with a pulse duration of about 10 ns. The trigger pulse is delivered along the longitudinal axis of the switch, and the focal spot can be placed anywhere along the axis of the 5-mm, gas-insulated gap between the switch electrodes. The switch test bed is designed to support a variety of working gases (e.g., Ar, N2) over a range of pressures. Electrical and optical diagnostics are used to measure switch performance as a function of parameters such as charge voltage, trigger pulse energy, insulating gas pressure, and gas species. A Mach-Zehnder imaging interferometer system operating at 532 nm is being used to obtain interferograms of the discharge plasma in the switch. We are also developing a 1064-nm interferometry diagnostic in an attempt to measure plasma free electron and neutral gas density profiles simultaneously within the switch gap. Results from our most recent experiments will be presented.

Transport simulation analysis of peripheral plasma with the open and the closed LHD divertor

International Nuclear Information System (INIS)

Kawamura, G.; Kobayashi, M.; Shoji, M.; Morisaki, T.; Masuzaki, S.; Feng, Y.

2014-10-01

Simulation modeling of the ergodic and divertor plasmas of the Large Helical Device (LHD) and its application to analysis of neutral particles, plasma, and impurity transport is presented. EMC3-EIRENE simulation with a new calculation mesh system is employed to evaluate effects of different divertor configurations: the open and the closed divertor. Qualitatively good agreement of neutral gas pressure with measurements was obtained, where the closed configuration causes roughly 20 times higher pressure under a dome structure than the open configuration. Effects of different configurations and gas pumping were investigated to understand recycling. Impurity accumulation and impurity screening in the ergodic region were investigated and differences caused by the configurations are evaluated. The closed configuration causes large impurity accumulation but the impurity screening effect suppress the accumulation at the same level of as the open configuration. (author)

Electron collisions in gas switches

International Nuclear Information System (INIS)

Christophorou, L.G.

1989-01-01

Many technologies rely on the conduction/insulation properties of gaseous matter for their successful operation. Many others (e.g., pulsed power technologies) rely on the rapid change (switching or modulation) of the properties of gaseous matter from an insulator to a conductor and vice versa. Studies of electron collision processes in gases aided the development of pulsed power gas switches, and in this paper we shall briefly illustrate the kind of knowledge on electron collision processes which is needed to optimize the performance of such switching devices. To this end, we shall refer to three types of gas switches: spark gap closing, self-sustained diffuse discharge closing, and externally-sustained diffuse discharge opening. 24 refs., 15 figs., 2 tabs

Oxygen plasma assisted end-opening and field emission enhancement in vertically aligned multiwall carbon nanotubes

International Nuclear Information System (INIS)

Mathur, A.; Roy, S.S.; Hazra, K.S.; Wadhwa, S.; Ray, S.C.; Mitra, S.K.; Misra, D.S.; McLaughlin, J.A.

2012-01-01

Highlights: ► We showed Ar/O 2 plasma can be effective for the end opening of aligned CNTs. ► The field emission property was dramatically enhanced after plasma modification. ► Microstructures were clearly understood by Raman and SEM analysis. ► Surface wet-ability at various functionalised conditions was studied. - Abstract: This paper highlights the changes in micro-structural and field emission properties of vertically aligned carbon nanotubes (VACNTs) via oxygen plasma treatment. We find that exposure of very low power oxygen plasma (6 W) at 13.56 MHz for 15–20 min, opens the tip of vertically aligned CNTs. Scanning electron microscopy and transmission electron microscopy images were used to identify the quality and micro-structural changes of the nanotube morphology and surfaces. Raman spectra showed that the numbers of defects were increased throughout the oxygen plasma treatment process. In addition, the hydrophobic nature of the VACNTs is altered significantly and the contact angle decreases drastically from 110° to 40°. It was observed that the electron field emission (EFE) characteristics are significantly enhanced. The turn-on electric field (ETOE) of CNTs decreased from ∼0.80 V μm −1 (untreated) to ∼0.60 V μm −1 (oxygen treated). We believe that the open ended VACNTs would be immensely valuable for applications such as micro/nanofluidic based filtering elements and display devices.

Oxygen plasma assisted end-opening and field emission enhancement in vertically aligned multiwall carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Mathur, A. [NIBEC, School of Engineering, University of Ulster, Jordanstown, BT37 0QB (United Kingdom); Roy, S.S., E-mail: sinharoy@ualberta.ca [Department of Mechanical Engineering, University of Alberta, Edmonton, T6T 2G8 (Canada); Hazra, K.S. [Department of Physics, IIT Bombay, Powai, Mumbai-400076 (India); Wadhwa, S. [NIBEC, School of Engineering, University of Ulster, Jordanstown, BT37 0QB (United Kingdom); Ray, S.C. [School of Physics, University of the Witwatersrand, WITS 2050, Johannesburg (South Africa); Mitra, S.K. [Department of Mechanical Engineering, University of Alberta, Edmonton, T6T 2G8 (Canada); Misra, D.S. [Department of Physics, IIT Bombay, Powai, Mumbai-400076 (India); McLaughlin, J.A. [NIBEC, School of Engineering, University of Ulster, Jordanstown, BT37 0QB (United Kingdom)

2012-05-15

Highlights: Black-Right-Pointing-Pointer We showed Ar/O{sub 2} plasma can be effective for the end opening of aligned CNTs. Black-Right-Pointing-Pointer The field emission property was dramatically enhanced after plasma modification. Black-Right-Pointing-Pointer Microstructures were clearly understood by Raman and SEM analysis. Black-Right-Pointing-Pointer Surface wet-ability at various functionalised conditions was studied. - Abstract: This paper highlights the changes in micro-structural and field emission properties of vertically aligned carbon nanotubes (VACNTs) via oxygen plasma treatment. We find that exposure of very low power oxygen plasma (6 W) at 13.56 MHz for 15-20 min, opens the tip of vertically aligned CNTs. Scanning electron microscopy and transmission electron microscopy images were used to identify the quality and micro-structural changes of the nanotube morphology and surfaces. Raman spectra showed that the numbers of defects were increased throughout the oxygen plasma treatment process. In addition, the hydrophobic nature of the VACNTs is altered significantly and the contact angle decreases drastically from 110 Degree-Sign to 40 Degree-Sign . It was observed that the electron field emission (EFE) characteristics are significantly enhanced. The turn-on electric field (ETOE) of CNTs decreased from {approx}0.80 V {mu}m{sup -1} (untreated) to {approx}0.60 V {mu}m{sup -1} (oxygen treated). We believe that the open ended VACNTs would be immensely valuable for applications such as micro/nanofluidic based filtering elements and display devices.

Beginning Microsoft Visual Studio LightSwitch Development

CERN Document Server

Novák, István

2011-01-01

Learn how LightSwitch can accelerate and simplify application development As Microsoft's newest offering for simplifying application development, LightSwitch opens the development door to creating applications without writing code. This introductory, full-color book shows you how to quickly create, modify, and distribute information for your business with LightSwitch. Packed with simple example programs, this beginner-level resource guides you through a complete small business application using LightSwitch to demonstrate the capabilities of this exciting new tool. You'll explore the most commo

Subnanosecond linear GaAs photoconductive switching: Revision 1

Energy Technology Data Exchange (ETDEWEB)

Druce, R.L.; Pocha, M.D.; Griffin, K.L.; Hofer, W.W.

1989-01-01

We are conducting research in photoconductive switching for the purpose of generating subnanosecond pulses in the 25--50kV range. We are exploiting the very fast recombination rates of Gallium Arsenide (GaAs) to explore the potential of GaAs as a closing and opening switch when operating in the linear mode (the linear mode is defined such that one carrier pair is generated for each photon absorbed). The closing time of a linear GaAs switch is theoretically limited by the characteristics of the laser pulse used to activate the switch (the carrier generation time in GaAs is /approximately/10/sup /minus/14/ sec) while the opening time is theoretically limited by the recombination time of the carriers. The recombination time is several ns for commercially available semi-insulating GaAs. Doping or neutron irradiation can reduce the recombination time to less than 100 ps. We have observed switch closing times of less than 200 ps with a 100 ps duration laser pulse and opening times of less than 400 ps with neutron irradiated GaAs at fields of tens of kV/cm. The illumination source was a Nd:YAG laser operating at 1.06 /mu/m. 4 refs., 11 figs.

High-speed 2 × 2 silicon-based electro-optic switch with nanosecond switch time

International Nuclear Information System (INIS)

Xue-Jun, Xu; Shao-Wu, Chen; Hai-Hua, Xu; Yang, Sun; Yu-De, Yu; Jin-Zhong, Yu; Qi-Ming, Wang

2009-01-01

A 2 × 2 electro-optic switch is experimentally demonstrated using the optical structure of a Mach–Zehnder interferometer (MZI) based on a submicron rib waveguide and the electrical structure of a PIN diode on silicon-on-insulator (SOI). The switch behaviour is achieved through the plasma dispersion effect of silicon. The device has a modulation arm of 1 mm in length and cross-section of 400 nm×340 nm. The measurement results show that the switch has a V π L π figure of merit of 0.145 V·cm and the extinction ratios of two output ports and cross talk are 40 dB, 28 dB and −28 dB, respectively. A 3 dB modulation bandwidth of 90 MHz and a switch time of 6.8 ns for the rise edge and 2.7 ns for the fall edge are also demonstrated

High current vacuum closing switch

International Nuclear Information System (INIS)

Dolgachev, G.I.; Maslennikov, D.D.; Romanov, A.S.; Ushakov, A.G.

2005-01-01

The paper proposes a powerful pulsed closing vacuum switch for high current commutation consisting of series of the vacuum diodes with near 1 mm gaps having closing time determined by the gaps shortening with the near-electrode plasmas [ru

Protection of active implant electronics with organosilicon open air plasma coating for plastic overmolding

Directory of Open Access Journals (Sweden)

Zeppenfeld Matthias

2016-09-01

Full Text Available To overcome challenges for manufacturing of modern smart medical plastic parts by injection molding, e.g. for active implants, the optimization of the interface between electronics and the polymer component concerning adhesion and diffusion behavior is crucial. Our results indicate that a nano-sized SiOxCyHz layer formed by plasma-enhanced chemical vapour deposition (PE-CVD via open air atmospheric pressure plasma jet (APPJ and by use of a hexamthyldisiloxane (HMDSO precursor can form a non-corrosive, anti-permeable and biocompatible coating. Due to the open air character of the APPJ process an inline coating before overmolding could be an easy applicable method and a promising advancement.

High voltage disconnect switch position monitoring

Energy Technology Data Exchange (ETDEWEB)

Crampton, S W

1983-08-01

Unreliable position indication on high-voltage (HV) disconnect switches can result in equipment damage worth many times the cost of a disconnect switch. The benefits and limitations of a number of possible methods of reliably monitoring HV disconnect switches are assessed. Several methods of powering active devices at HV are noted. It is concluded that the most reliable way of monitoring switch position at reasonable cost would use a passive hermetically-sealed blade-position sensor located at HV, with a fibre-optic link between HV and ground. Separate sensors would be used for open and closed position indication. For maximum reliability the fibre-optic link would continue into the relay building. A passive magnetically actuated fibre-optic sensor has been built which demonstrates the feasibility of the concept. The sensor monitors blade position relative to the jaws in three dimensions with high resolution. A design for an improved passive magneto-optic sensor has significantly lower optical losses, allowing a single fibre-optic loop and 3 sensors to monitor closure of all phases of a disconnect switch. A similar loop would monitor switch opening. The improved sensor has a solid copper housing to provide greater immunity to fault currents, and to protect it from the environment and from physical damage. Two methods of providing a protected path for fibre-optics passing from HV to ground are proposed, one using a hollow porcelain switch-support insulator and the other using an additional small-diameter polymer insulator with optical fibres imbedded in its fibreglass core. A number of improvements are recommended which can be made to existing switches to increase their reliability. 16 refs., 13 figs., 1 tab.

Shock wave interaction with pulsed glow discharge and afterglow plasmas

International Nuclear Information System (INIS)

Podder, N.K.; LoCascio, A.C.

2009-01-01

Acoustic shock waves are launched by the spark-discharge of a high voltage capacitor in pulsed glow discharge and afterglow plasmas. The glow discharge section of the shock tube is switched on for a period of less than one second at a time, during which a shock wave is launched starting with a large delay between the plasma switch-on and the shock-launch. In the subsequent runs this delay is decremented in equal time intervals up to the plasma switch-on time. A photo acoustic deflection method sensitive to the density gradient of the shock wave is used to study the propagating shock structure and velocity in the igniting plasma. A similar set of measurements are also performed at the plasma switch-off, in which the delay time is incremented in equal time intervals from the plasma switch-off time until the afterglow plasma fully neutralizes itself into the room-temperature gas. Thus, complete time histories of the shock wave propagation in the igniting plasma, as well as in the afterglow plasma, are produced. In the igniting plasma, the changes in the shock-front velocity and dispersion are found to be a strong non-linear function of delay until a saturation point is reached. On the other hand, in the afterglow plasma the trend has been opposite and reversing towards the room temperature values. The observed shock wave properties in both igniting and afterglow plasmas correlate well with the inferred temperature changes in the two plasmas

Pinching evidences in a miniature plasma focus with fast pseudospark switch

International Nuclear Information System (INIS)

Hassan, S M; Zhang, T; Patran, A; Rawat, R S; Springham, S V; Tan, T L; Wong, D; Wang, W; Lee, S; Gribkov, V A; Mohanty, S R; Lee, P

2006-01-01

We report the observations of pinching in a miniature plasma focus (PF) (58-160 J) operated in repetitive mode using fast pseudospark switch (PSS). The size of the device, which includes the capacitor bank, PSS and the focus chamber, is of the order of 22 cm x 22 cm x 38 cm. Several diagnostic tools, the gated imager, streak camera, current and voltage probe, are employed simultaneously to confirm the occurrence of pinching in this fast miniature PF device. The device is optimized for operation in neon and hydrogen as the working gas. The best focus formation was obtained at pressures between 0.5 to 8.0 mbar for neon and between 7.0 to 15.0 mbar for hydrogen. When the system was operated at 100 J with hydrogen as the filling gas, the typical dip in the current derivative signal and the typical peak in the voltage signal associated with pinch compression, are observed to be most intense indicating efficient pinching in the miniature PF device

Validating an infrared thermal switch as a novel access technology

Directory of Open Access Journals (Sweden)

Memarian Negar

2010-08-01

Full Text Available Abstract Background Recently, a novel single-switch access technology based on infrared thermography was proposed. The technology exploits the temperature differences between the inside and surrounding areas of the mouth as a switch trigger, thereby allowing voluntary switch activation upon mouth opening. However, for this technology to be clinically viable, it must be validated against a gold standard switch, such as a chin switch, that taps into the same voluntary motion. Methods In this study, we report an experiment designed to gauge the concurrent validity of the infrared thermal switch. Ten able-bodied adults participated in a series of 3 test sessions where they simultaneously used both an infrared thermal and conventional chin switch to perform multiple trials of a number identification task with visual, auditory and audiovisual stimuli. Participants also provided qualitative feedback about switch use. User performance with the two switches was quantified using an efficiency measure based on mutual information. Results User performance (p = 0.16 and response time (p = 0.25 with the infrared thermal switch were comparable to those of the gold standard. Users reported preference for the infrared thermal switch given its non-contact nature and robustness to changes in user posture. Conclusions Thermal infrared access technology appears to be a valid single switch alternative for individuals with disabilities who retain voluntary mouth opening and closing.

Switch from a ZDV/3TC-based regimen to a completely once daily (QD regimen of emtricitabine/tenofovir DF fixed dose combination plus a third QD agent (SONETT

Directory of Open Access Journals (Sweden)

Arasteh K

2009-05-01

Full Text Available Abstract Objectives To assess the efficacy and safety of a treatment switch from a twice-daily (BID regimen containing zidovudine (ZDV and lamivudine (3TC plus a third agent to a once daily (QD regimen containing the fixed-dose combination of tenofovir DF/emtricitabine (TDF/FTC, Truvada® plus a divergent third QD agent in HIV-1 infected patients. Methods Prospective, 48-week, non-randomised, single-group, open-label, study. Fifty-one patients on stable ZDV/3TC-containing HAART, with HIV-1 RNA 50 cells/μl, were switched to TDF/FTC plus a third agent. Plasma HIV-1 RNA, CD4+ and CD8+ T-cell counts were assessed at baseline and weeks 4, 12, 24, 36 and 48 post-switch. Results During the 48-week study, 10 patients discontinued prematurely, including three due to adverse events (AEs. At week 48, plasma HIV-1 RNA was p Conclusions Results from this study support switching from a ZDV/3TC-containing HAART regimen to a completely QD regimen of TDF/FTC plus a third agent. Virologic and immunologic control are maintained, with apparent benefits in haemoglobin.

Investigation on properties of ultrafast switching in a bulk gallium arsenide avalanche semiconductor switch

International Nuclear Information System (INIS)

Hu, Long; Su, Jiancang; Ding, Zhenjie; Hao, Qingsong; Yuan, Xuelin

2014-01-01

Properties of ultrafast switching in a bulk gallium arsenide (GaAs) avalanche semiconductor switch based on semi-insulating wafer, triggered by an optical pulse, were analyzed using physics-based numerical simulations. It has been demonstrated that when a voltage with amplitude of 5.2 kV is applied, after an exciting optical pulse with energy of 1 μJ arrival, the structure with thickness of 650 μm reaches a high conductivity state within 110 ps. Carriers are created due to photons absorption, and electrons and holes drift to anode and cathode terminals, respectively. Static ionizing domains appear both at anode and cathode terminals, and create impact-generated carriers which contribute to the formation of electron-hole plasma along entire channel. When the electric field in plasma region increases above the critical value (∼4 kV/cm) at which the electrons drift velocity peaks, a domain comes into being. An increase in carrier concentration due to avalanche multiplication in the domains reduces the domain width and results in the formation of an additional domain as soon as the field outside the domains increases above ∼4 kV/cm. The formation and evolution of multiple powerfully avalanching domains observed in the simulations are the physical reasons of ultrafast switching. The switch exhibits delayed breakdown with the characteristics affected by biased electric field, current density, and optical pulse energy. The dependence of threshold energy of the exciting optical pulse on the biased electric field is discussed

Pacemaker reed switch behavior in 0.5, 1.5, and 3.0 Tesla magnetic resonance imaging units: are reed switches always closed in strong magnetic fields?

Science.gov (United States)

Luechinger, Roger; Duru, Firat; Zeijlemaker, Volkert A; Scheidegger, Markus B; Boesiger, Peter; Candinas, Reto

2002-10-01

MRI is established as an important diagnostic tool in medicine. However, the presence of a cardiac pacemaker is usually regarded as a contraindication for MRI due to safety reasons. The aim of this study was to investigate the state of a pacemaker reed switch in different orientations and positions in the main magnetic field of 0.5-, 1.5-, and 3.0-T MRI scanners. Reed switches used in current pacemakers and ICDs were tested in 0.5-, 1.5-, and 3.0-T MRI scanners. The closure of isolated reed switches was evaluated for different orientations and positions relative to the main magnetic field. The field strengths to close and open the reed switch and the orientation dependency of the closed state inside the main magnetic field were investigated. The measurements were repeated using two intact pacemakers to evaluate the potential influence of the other magnetic components, like the battery. If the reed switches were oriented parallel to the magnetic fields, they closed at 1.0 +/- 0.2 mT and opened at 0.7 +/- 0.2 mT. Two different reed switch behaviors were observed at different magnetic field strengths. In low magnetic fields ( 200 mT), the reed switches opened in 50% of all tested orientations. No difference between the three scanners could be demonstrated. The reed switches showed the same behavior whether they were isolated or an integral part of the pacemakers. The reed switch in a pacemaker or an ICD does not necessarily remain closed in strong magnetic fields at 0.5, 1.5, or 3.0 T and the state of the reed switch may not be predictable with certainty in clinical situations.

Repetitive switching for an electromagnetic rail gun

Science.gov (United States)

Gruden, J. M.

1983-12-01

Previous testing on a repetitive opening switch for inductive energy storage has proved the feasibility of the rotary switch concept. The concept consists of a rotating copper disk (rotor) with a pie-shaped insulator section and brushes which slide along each of the rotor surfaces. While on top of the copper surface, the brushes and rotor conduct current allowing the energy storage inductor to charge. When the brushes slide onto the insulator section, the current cannot pass through the rotor and is diverted into the load. This study investigates two new brush designs and a rotor modification designed to improve the current commutating capabilities of the switch. One brush design (fringe fiber) employs carbon fibers on the leading and trailing edge of the brush to increase the resistive commutating action as the switch opens and closes. The other brush design uses fingers to conduct current to the rotor surface, effectively increasing the number of brush contact points. The rotor modification was the placement of tungsten inserts at the copper-insulator interfaces.

Switched Broadband Services For The Home

Science.gov (United States)

Sawyer, Don M.

1990-01-01

In considering the deployment of fiber optics to the residence, two critical questions arise: what are the leading services that could be offered to justify the required investment; and what is the nature of the business that would offer these services to the consumer ? This talk will address these two questions together with the related issue of how the "financial engine" of today's television distribution infrastructure - TV advertising - would be affected by an open access system based on fiber optics coupled with broadband switching. On the business side, the talk concludes that the potential for open ended capacity expansion, fair competition between service providers, and new interactive services inherent in an open access, switched broadband system are the critical items in differentiating it from existing video and TV distribution systems. On the question of broadband services, the talk will highlight several new opportunities together with some findings from recent market research conducted by BNR. The talk will show that there are variations on existing services plus many new services that could be offered and which have real consumer appeal. The postulated open access system discussed here is visualized as having ultimately 1,000 to 2,000 video channels available to the consumer. Although this may appear to hopelessly fragment the TV audience and destroy the current TV advertising infrastructure, the technology of open access, switched broadband will present many new advertising techniques, which have the potential to be far more effective than those available today. Some of these techniques will be described in this talk.

Light-Induced Switching of Tunable Single-Molecule Junctions

KAUST Repository

Sendler, Torsten; Luka-Guth, Katharina; Wieser, Matthias; Lokamani; Wolf, Jannic Sebastian; Helm, Manfred; Gemming, Sibylle; Kerbusch, Jochen; Scheer, Elke; Huhn, Thomas; Erbe, Artur

2015-01-01

A major goal of molecular electronics is the development and implementation of devices such as single-molecular switches. Here, measurements are presented that show the controlled in situ switching of diarylethene molecules from their nonconductive to conductive state in contact to gold nanoelectrodes via controlled light irradiation. Both the conductance and the quantum yield for switching of these molecules are within a range making the molecules suitable for actual devices. The conductance of the molecular junctions in the opened and closed states is characterized and the molecular level E 0, which dominates the current transport in the closed state, and its level broadening Γ are identified. The obtained results show a clear light-induced ring forming isomerization of the single-molecule junctions. Electron withdrawing side-groups lead to a reduction of conductance, but do not influence the efficiency of the switching mechanism. Quantum chemical calculations of the light-induced switching processes correlate these observations with the fundamentally different low-lying electronic states of the opened and closed forms and their comparably small modification by electron-withdrawing substituents. This full characterization of a molecular switch operated in a molecular junction is an important step toward the development of real molecular electronics devices.

Light-Induced Switching of Tunable Single-Molecule Junctions

KAUST Repository

Sendler, Torsten

2015-04-16

A major goal of molecular electronics is the development and implementation of devices such as single-molecular switches. Here, measurements are presented that show the controlled in situ switching of diarylethene molecules from their nonconductive to conductive state in contact to gold nanoelectrodes via controlled light irradiation. Both the conductance and the quantum yield for switching of these molecules are within a range making the molecules suitable for actual devices. The conductance of the molecular junctions in the opened and closed states is characterized and the molecular level E 0, which dominates the current transport in the closed state, and its level broadening Γ are identified. The obtained results show a clear light-induced ring forming isomerization of the single-molecule junctions. Electron withdrawing side-groups lead to a reduction of conductance, but do not influence the efficiency of the switching mechanism. Quantum chemical calculations of the light-induced switching processes correlate these observations with the fundamentally different low-lying electronic states of the opened and closed forms and their comparably small modification by electron-withdrawing substituents. This full characterization of a molecular switch operated in a molecular junction is an important step toward the development of real molecular electronics devices.

Energy losses in switches

International Nuclear Information System (INIS)

Martin, T.H.; Seamen, J.F.; Jobe, D.O.

1993-01-01

The authors experiments show energy losses between 2 and 10 times that of the resistive time predictions. The experiments used hydrogen, helium, air, nitrogen, SF 6 polyethylene, and water for the switching dielectric. Previously underestimated switch losses have caused over predicting the accelerator outputs. Accurate estimation of these losses is now necessary for new high-efficiency pulsed power devices where the switching losses constitute the major portion of the total energy loss. They found that the switch energy losses scale as (V peak I peak ) 1.1846 . When using this scaling, the energy losses in any of the tested dielectrics are almost the same. This relationship is valid for several orders of magnitude and suggested a theoretical basis for these results. Currents up to .65 MA, with voltages to 3 MV were applied to various gaps during these experiments. The authors data and the developed theory indicates that the switch power loss continues for a much longer time than the resistive time, with peak power loss generally occurring at peak current in a ranging discharge instead of the early current time. All of the experiments were circuit code modeled after developing a new switch loss version based on the theory. The circuit code predicts switch energy loss and peak currents as a function of time. During analysis of the data they noticed slight constant offsets between the theory and data that depended on the dielectric. They modified the plasma conductivity for each tested dielectric to lessen this offset

OpenFlow cookbook

CERN Document Server

Smiler S, Kingston

2015-01-01

This book is intended for network protocol developers, SDN controller application developers, and academics who would like to understand and develop their own OpenFlow switch or OpenFlow controller in any programming language. With basic understanding of OpenFlow and its components, you will be able to follow the recipes in this book.

Plasma pro-atrial natriuretic peptide to estimate fluid balance during open and robot-assisted esophagectomy

DEFF Research Database (Denmark)

Strandby, Rune Broni; Ambrus, Rikard; Secher, Niels H

2017-01-01

BACKGROUND: It remains debated how much fluid should be administered during surgery. The atrial natriuretic peptide precursor proANP is released by atrial distension and deviations in plasma proANP are reported associated with perioperative fluid balance. We hypothesized that plasma proANP would...... decrease when the central blood volume is compromised during the abdominal part of robot-assisted hybrid (RE) esophagectomy and that a positive fluid balance would be required to maintain plasma proANP. METHODS: Patients undergoing RE (n = 25) or open (OE; n = 25) esophagectomy for gastroesophageal cancer...

Ultralow field emission from thinned, open-ended, and defected carbon nanotubes by using microwave hydrogen plasma processing

Energy Technology Data Exchange (ETDEWEB)

Deng, Jian-Hua, E-mail: jhdeng1983@163.com [College of Physics and Materials Science, Tianjin Normal University, Tianjin 300387 (China); Cheng, Lin; Wang, Fan-Jie; Yu, Bin; Li, Guo-Zheng; Li, De-Jun [College of Physics and Materials Science, Tianjin Normal University, Tianjin 300387 (China); Cheng, Guo-An [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, Beijing Normal University, Beijing 100875 (China)

2015-01-01

Graphical abstract: Thinned, open-ended, and defected carbon nanotubes were prepared by using hydrogen plasma processing. The processed carbon nanotubes have far better field emission performance than that of the pristine ones. - Highlights: • CVD prepared CNT arrays were processed by microwave hydrogen plasma. • Thinned, open-ended, and defected CNTs were obtained. • Processed CNTs have far better field emission performance than the pristine ones. • Processed CNTs have applicable emission stability after being perfectly aged. - Abstract: Ultralow field emission is achieved from carbon nanotubes (CNTs) by using microwave hydrogen plasma processing. After the processing, typical capped CNT tips are removed, with thinned, open-ended, and defected CNTs left. Structural analyses indicate that the processed CNTs have more SP{sup 3}-hybridized defects as compared to the pristine ones. The morphology of CNTs can be readily controlled by adjusting microwave powers, which change the shape of CNTs by means of hydrogen plasma etching. Processed CNTs with optimal morphology are found to have an ultralow turn-on field of 0.566 V/μm and threshold field of 0.896 V/μm, much better than 0.948 and 1.559 V/μm of the as-grown CNTs, respectively. This improved FE performance is ascribed to the structural changes of CNTs after the processing. The thinned and open-ended shape of CNTs can facilitate electron tunneling through barriers and additionally, the increased defects at tube walls can serve as new active emission sites. Furthermore, our plasma processed CNTs exhibit excellent field emission stability at a large emission current density of 10.36 mA/cm{sup 2} after being perfectly aged, showing promising prospects in applications as high-performance vacuum electron sources.

Jet outflow and open field line measurements on the C-2U advanced beam-driven field-reversed configuration plasma experiment.

Science.gov (United States)

Sheftman, D; Gupta, D; Roche, T; Thompson, M C; Giammanco, F; Conti, F; Marsili, P; Moreno, C D

2016-11-01

Knowledge and control of the axial outflow of plasma particles and energy along open-magnetic-field lines are of crucial importance to the stability and longevity of the advanced beam-driven field-reversed configuration plasma. An overview of the diagnostic methods used to perform measurements on the open field line plasma on C-2U is presented, including passive Doppler impurity spectroscopy, microwave interferometry, and triple Langmuir probe measurements. Results of these measurements provide the jet ion temperature and axial velocity, electron density, and high frequency density fluctuations.

Investigation of stability and x-ray spectrum in gas-puff z-pinch plasmas diriven by inductive energy storage pulsed power generator with a plasma opening switch

International Nuclear Information System (INIS)

Murayama, K.; Fukudome, I.; Teramoto, Y.; Katsuki, S.; Akiyama, H.

2002-01-01

Gas-puff z-pinch plasmas are driven by an inductive voltage adder - inductive energy storage pulsed power generator ''ASO-X''. ASO-X has the performance of the maximum output voltage and current are 180 kV and 400 kA respectively and can provide a fast rise time current with operating POS. The stability of the plasma column, spectrum radiated from z-pinch plasmas and the spatial distribution of hot spots are investigated in the case with and without operating POS. By driving ASO-X with operating POS the kink instability is restrained and the stability of plasma column is improved about three times in regard to the average dispersion. Furthermore the duration of soft x-ray radiation is increased and the spatial distribution of hot spots is 50% improved with regard to kurtosis of the intensity profile of pinhole photographs compared to those without operating POS. (author)

Improved performance of a plasma filled diode when driven by a PEOS

International Nuclear Information System (INIS)

Goyer, J.R.; Barreto, G.; Sincerny, P.S.; Krishnan, M.

1988-01-01

The plasma filled diode (PFD) has been used successfully to provide pulse compression and power multiplication for the fast Marx bank EYESS at Physics International. It has been found that the addition of a plasma erosion opening switch (PEOS) between the Marx bank and PFD increases the voltage and power at the diode while reducing the FWHM of the power pulse. Typical results obtained when using the PFD alone are power pulsewidths of 150 ns (FWHM) with a peak power of 500 GW at 1.1 MV. When the PEOS is included, the power pulsewidth narrows to 90 ns (FWHM) and the peak power increases to 550 GW at 1.5 MV. A description is given of the Marx bank, diode hardware, and plasma injection technique along with a presentation of diagnostic waveforms

High-power subnanosecond operation of a bistable optically controlled semiconductor switch (BOSS)

International Nuclear Information System (INIS)

Stoudt, D.C.; Richardson, M.A.; Demske, D.L.; Roush, R.A.; Eure, K.W.

1994-01-01

Recent high-power, subnanosecond-switching results of the Bistable Optically controlled Semiconductor Switch (BOSS) are presented. The process of persistent photoconductivity followed by photo-quenching have been demonstrated at megawatt power levels in copper-compensated, silicon-doped, semi-insulating gallium arsenide. These processes allow a switch to be developed that can be closed by the application of one laser pulse and opened by the application of a second laser pulse with a wavelength equal to twice that of the first laser. Switch closure is primarily achieved by elevating electrons from a deep copper center which has been diffused into the material. The opening phase is a two-step process which relies initially on the absorption of the 2-μm laser causing electrons to be elevated from the valance band back into the copper center, and finally on the recombination of electrons in the conduction band with boles in the valance band. The second step requires a sufficient concentration of recombination centers (RC) in the material for opening to occur in the subnanosecond regime. These RC's are generated in the bulk GaAs material by fast-neutron irradiation (∼ 1 MeV) at a fluence of about 3 x 10 15 cm -2 . High-power switching results which demonstrate that the BOSS switch can be opened in the subnanosecond regime are presented for the first time. Neutron-irradiated BOSS devices have been opened against a rising electric field of about 20 kV/cm (10 kV) in a time less than one nanosecond. Kilovolt electrical pulses have been generated with a FWHM of roughly 250 picoseconds

Investigation of stability and x-ray spectrum in gas-puff z-pinch plasmas diriven by inductive energy storage pulsed power generator with a plasma opening switch

Energy Technology Data Exchange (ETDEWEB)

Murayama, K.; Fukudome, I. [Yatsushiro National College of Technology, Dept. of Mechanical and Electrical Engineering, Yatsushiro, Kumamoto (Japan); Teramoto, Y.; Katsuki, S.; Akiyama, H. [Kumamoto Univ., Dept. of Electrical and Computer Engineering, Kumamoto (Japan)

2002-06-01

Gas-puff z-pinch plasmas are driven by an inductive voltage adder - inductive energy storage pulsed power generator ''ASO-X''. ASO-X has the performance of the maximum output voltage and current are 180 kV and 400 kA respectively and can provide a fast rise time current with operating POS. The stability of the plasma column, spectrum radiated from z-pinch plasmas and the spatial distribution of hot spots are investigated in the case with and without operating POS. By driving ASO-X with operating POS the kink instability is restrained and the stability of plasma column is improved about three times in regard to the average dispersion. Furthermore the duration of soft x-ray radiation is increased and the spatial distribution of hot spots is 50% improved with regard to kurtosis of the intensity profile of pinhole photographs compared to those without operating POS. (author)

High-Voltage MOSFET Switching Circuit

Science.gov (United States)

Jensen, Kenneth A.

1995-01-01

Circuit reliably switches power at supply potential of minus 1,500 V, with controlled frequency and duty cycle. Used in argon-plasma ion-bombardment equipment for texturing copper electrodes, as described in "Texturing Copper To Reduce Secondary Emission of Electrons" (LEW-15898), also adapted to use in powering gaseous flash lamps and stroboscopes.

Transverse current at the periphery of the start plasma of the AMBAL-M open device

International Nuclear Information System (INIS)

Taskaev, S.Yu.

1999-01-01

Essential longitudinal electron current was experimentally detected earlier in a start plasma of AMBAL-M open trap and system. This paper studies the current at a plasma periphery and the process resulting in occurrence of transverse current, and determines the value of a transverse current in a transporting range. This study enables to determine that filling of a trap with a thin circular flow and formation of nonequilibrium distribution of a radial electrical field in a plasma by potentials of an electrode front gun are the indium peculiarities of the experiment ensuring essential transverse current [ru

Microwave pulse generation by photoconductive switching

Energy Technology Data Exchange (ETDEWEB)

Pocha, M.D.; Druce, R.L.

1989-03-14

Laser activated photoconductive semiconductor switching shows significant potential for application in high power microwave generation. Primary advantages of this concept are: small size, light weight, ruggedness, precise timing and phasing by optical control, and the potential for high peak power in short pulses. Several concepts have been suggested for microwave generation using this technology. They generally fall into two categories (1) the frozen wave generator or (2) tuned cavity modulation, both of which require only fast closing switches. We have been exploring a third possibility requiring fast closing and opening switches, that is the direct modulation of the switch at microwave frequencies. Switches have been fabricated at LLNL using neutron irradiated Gallium Arsenide which exhibit response times as short as 50 ps at low voltages. We are in the process of performing high voltage tests. So far, we have been able to generate 2.4 kV pulses with approximately 340 ps response time (FWHM) using approximately a 200..mu..J optical pulse. Experiments are continuing to increase the voltage and improve the switching efficiency. 3 refs., 6 figs.

Microwave pulse generation by photoconductive switching

Science.gov (United States)

Pocha, M. D.; Druce, R. L.

1989-03-01

Laser activated photoconductive semiconductor switching shows significant potential for application in high power microwave generation. Primary advantages of this concept are: small size, light weight, ruggedness, precise timing and phasing by optical control, and the potential for high peak power in short pulses. Several concepts have been suggested for microwave generation using this technology. They generally fall into two categories: (1) the frozen wave generator, or (2) tuned cavity modulation, both of which require only fast closing switches. We have been exploring a third possibility requiring fast closing and opening switches, that is the direct modulation of the switch at microwave frequencies. Switches have been fabricated at LLNL using neutron irradiated Gallium Arsenide which exhibit response times as short as 50 ps at low voltages. We are in the process of performing high voltage tests. So far, we have been able to generate 2.4 kV pulses with approximately 340 ps response time (FWHM) using approximately a 200 microJ optical pulse. Experiments are continuing to increase the voltage and improve the switching efficiency.

Changes of serum cortisol and plasma angiotensin-II (AT-II) levels in patients with open chest surgery during peri-operative stage

International Nuclear Information System (INIS)

Yu Yunyun; Tian Runhua; Zhao Huiyuan; Li Xiaoqin; Wang Ling

2005-01-01

Objective: To assess the systemic stress reaction in patients with open chest surgery through measurement of the changes of serum cortisol and plasma AT-II levels during peri-operative stage. Methods: Serum cortisol and plasma AT-II levels were measured with RIA in 35 patients underwent open chest surgery both before and after the operative procedure. Results: The serum level of cortisol and plasma levels of AT-II were significantly higher after operation than those before operation ( P < 0.05 ). Also, the systolic pressure and heart rate were increased significantly (P<0.05). The post-operative heart rate was significantly positively correlated with both cortisol and AT-II levels (P<0.05). Conclusion: Stress reaction is evident in patients after open chest surgery with increase of serum cortisol and plasma AT-II levels. The stress reaction, if excessive, should be properly dealt with. (authors)

The Robustness of Stochastic Switching Networks

OpenAIRE

Loh, Po-Ling; Zhou, Hongchao; Bruck, Jehoshua

2009-01-01

Many natural systems, including chemical and biological systems, can be modeled using stochastic switching circuits. These circuits consist of stochastic switches, called pswitches, which operate with a fixed probability of being open or closed. We study the effect caused by introducing an error of size ∈ to each pswitch in a stochastic circuit. We analyze two constructions – simple series-parallel and general series-parallel circuits – and prove that simple series-parallel circuits are robus...

Collisional and radiative processes in high-pressure discharge plasmas

Science.gov (United States)

Becker, Kurt H.; Kurunczi, Peter F.; Schoenbach, Karl H.

2002-05-01

Discharge plasmas at high pressures (up to and exceeding atmospheric pressure), where single collision conditions no longer prevail, provide a fertile environment for the experimental study of collisions and radiative processes dominated by (i) step-wise processes, i.e., the excitation of an already excited atomic/molecular state and by (ii) three-body collisions leading, for instance, to the formation of excimers. The dominance of collisional and radiative processes beyond binary collisions involving ground-state atoms and molecules in such environments allows for many interesting applications of high-pressure plasmas such as high power lasers, opening switches, novel plasma processing applications and sputtering, absorbers and reflectors for electromagnetic waves, remediation of pollutants and waste streams, and excimer lamps and other noncoherent vacuum-ultraviolet light sources. Here recent progress is summarized in the use of hollow cathode discharge devices with hole dimensions in the range 0.1-0.5 mm for the generation of vacuum-ultraviolet light.

Subnanosecond, high-voltage photoconductive switching in GaAs

Science.gov (United States)

Druce, Robert L.; Pocha, Michael D.; Griffin, Kenneth L.; O'Bannon, Jim

1991-03-01

We are conducting research on the switching properties of photoconductive materials to explore their potential for generating highpower microwaves (HPM) and for high reprate switching. We have investigated the performance of Gallium Arsenide (GaAs) in linear mode (the conductivity of the device follows the optical pulse) as well as an avalanchelike mode (the optical pulse only controls switch closing) . Operating in the unear mode we have observed switch closing times of less than 200 Ps with a 100 ps duration laser pulse and opening times of less than 400 ps at several kV/cm fields using neutron irradiated GaAs. In avalanche and lockon modes high fields are switched with lower laser pulse energies resulting in higher efficiencies but with measurable switching delay and jitter. We are currently investigating both large area (1 cm2) and small area 1 mm2) switches illuminated by AlGaAs laser diodes at 900 nm and Nd:YAG lasers at 1. 06 tim.

Advances in high voltage power switching with GTOs

International Nuclear Information System (INIS)

Podlesak, T.F.

1990-01-01

The control of high voltage at high power, particularly opening switches, has been difficult in the past. Using gate turnoff thyristors (GTOs) arranged in series enables large currents to be switched at high voltage. The authors report a high voltage opening switch has been successfully demonstrated. This switch uses GTOs in series and successfully operates at voltages higher than the rated voltage of the individual devices. It is believed that this is the first time this has been successfully demonstrated, in that GTOs have been operated in series before, but always in a manner as to not exceed the voltage capability of the individual devices. In short, the devices have not worked together, sharing the voltage, but one device has been operated using several backup devices. Of particular interest is how well the individual devices share the voltage applied to them. Equal voltage sharing between devices is absolutely essential, in order to not exceed the voltage rating of any of the devices in the series chain. This is accomplished at high (microsecond) switching speeds. Thus, the system is useful for high frequency applications as well as high power, making for a flexible circuit system element. This demonstration system is rated at 5 KV and uses 1 KV devices. A larger 24 KV system is under design and will use 4.5 KV devices. In order to design the 24 KV switch, the safe operating area of the large devices must be known thoroughly

Plasma flow discharge researches at the PIRIT-2000 facility

International Nuclear Information System (INIS)

Popkov, N.F.; Ryaslov, E.A.; Kargin, V.I.; Pikar', A.S.; Vorontsov, V.I.; Kotel'nikov, D.V.; Melkozerov, A.V.

1996-01-01

Investigation of a plasma flow switch at the PIRIT-2000 fast operating capacitor bank is reported. The maximum current of the plasma flow discharge (PFD) reaches 5 MA, the current rise time being as low as 100 ns. The magnetic field strength of the plasma flow switch (0.15 T) is about 15 times higher than that of the plasma erosion switch used earlier. Both magnetic probe and optical methods were used in the experiments. From the magnetic probes data the propagating velocity of a current carrying shell (205 cm/s) has been derived, while the optical method is used for determining the velocity of a glowing plasma layer. At varying the operation delay in the range 2-10 s the PFD load current rise time increases up to 150-200 ns, the prepulse increment reaching its maximum at the delays higher than 6 s. (J.U.). 5 figs., 5 refs

Plasma flow discharge researches at the PIRIT-2000 facility

Energy Technology Data Exchange (ETDEWEB)

Popkov, N F; Ryaslov, E A; Kargin, V I; Pikar` , A S; Vorontsov, V I; Kotel` nikov, D V; Melkozerov, A V [All-Russian Scientific Research Inst. of Experimental Physics, Sarov (Russian Federation)

1997-12-31

Investigation of a plasma flow switch at the PIRIT-2000 fast operating capacitor bank is reported. The maximum current of the plasma flow discharge (PFD) reaches 5 MA, the current rise time being as low as 100 ns. The magnetic field strength of the plasma flow switch (0.15 T) is about 15 times higher than that of the plasma erosion switch used earlier. Both magnetic probe and optical methods were used in the experiments. From the magnetic probes data the propagating velocity of a current carrying shell (205 cm/s) has been derived, while the optical method is used for determining the velocity of a glowing plasma layer. At varying the operation delay in the range 2-10 s the PFD load current rise time increases up to 150-200 ns, the prepulse increment reaching its maximum at the delays higher than 6 s. (J.U.). 5 figs., 5 refs.

State Recognition of High Voltage Isolation Switch Based on Background Difference and Iterative Search

Science.gov (United States)

Xu, Jiayuan; Yu, Chengtao; Bo, Bin; Xue, Yu; Xu, Changfu; Chaminda, P. R. Dushantha; Hu, Chengbo; Peng, Kai

2018-03-01

The automatic recognition of the high voltage isolation switch by remote video monitoring is an effective means to ensure the safety of the personnel and the equipment. The existing methods mainly include two ways: improving monitoring accuracy and adopting target detection technology through equipment transformation. Such a method is often applied to specific scenarios, with limited application scope and high cost. To solve this problem, a high voltage isolation switch state recognition method based on background difference and iterative search is proposed in this paper. The initial position of the switch is detected in real time through the background difference method. When the switch starts to open and close, the target tracking algorithm is used to track the motion trajectory of the switch. The opening and closing state of the switch is determined according to the angle variation of the switch tracking point and the center line. The effectiveness of the method is verified by experiments on different switched video frames of switching states. Compared with the traditional methods, this method is more robust and effective.

49 CFR 236.528 - Restrictive condition resulting from open hand-operated switch; requirement.

Science.gov (United States)

2010-10-01

... SYSTEMS, DEVICES, AND APPLIANCES Automatic Train Stop, Train Control and Cab Signal Systems Rules and...-operated switch three-eighths inch or more, or hand-operated switch is not locked where facing point lock with circuit controller is used, the resultant restrictive condition of an automatic train stop or...

Sequential magnetic switching in Fe/MgO(001) superlattices

Science.gov (United States)

Magnus, F.; Warnatz, T.; Palsson, G. K.; Devishvili, A.; Ukleev, V.; Palisaitis, J.; Persson, P. O. Å.; Hjörvarsson, B.

2018-05-01

Polarized neutron reflectometry is used to determine the sequence of magnetic switching in interlayer exchange coupled Fe/MgO(001) superlattices in an applied magnetic field. For 19.6 Å thick MgO layers we obtain a 90∘ periodic magnetic alignment between adjacent Fe layers at remanence. In an increasing applied field the top layer switches first followed by its second-nearest neighbor. For 16.4 Å MgO layers, a 180∘ periodic alignment is obtained at remanence and with increasing applied field the layer switching starts from the two outermost layers and proceeds inwards. This sequential tuneable switching opens up the possibility of designing three-dimensional magnetic structures with a predefined discrete switching sequence.

Explosive-Emission Plasma Dynamics in Ion Diode in Double-Pulse Mode

International Nuclear Information System (INIS)

Pushkarev, Alexander I.; Isakova, Yulia I.

2011-01-01

The results of an experimental investigation of explosive-emission plasma dynamics in an ion diode with self-magnetic insulation are presented. The investigations were accomplished at the TEMP-4M accelerator set in a mode of double pulse formation. Plasma behaviour in the anode-cathode gap was analyzed according to both the current-voltage characteristics of the diode (time resolution of 0.5 ns) and thermal imprints on a target (spatial resolution of 0.8 mm). It was shown that when plasma formation at the potential electrode was complete, and up until the second (positive) pulse, the explosive-emission plasma expanded across the anode-cathode gap with a speed of 1.3±0.2 cm/μs. After the voltage polarity at the potential electrode was reversed (second pulse), the plasma erosion in the anode-cathode gap (similar to the effect of a plasma opening switch) occurred. During the generation of an ion beam the size of the anode-cathode gap spacing was determined by the thickness of the plasma layer on the potential electrode and the layer thickness of the electrons drifting along the grounded electrode. (15th asian conference on electrical discharge)

Radiation pattern of open ended waveguide in air core surrounded by annular plasma column

International Nuclear Information System (INIS)

Sharma, D.R.; Verma, J.S.

1977-01-01

Radiation pattern of open ended waveguide excited in circular symmetric mode (TM 01 ) in an air core having central conductor and surrounded by an annular plasma column is studied. The field distribution at the open end of the waveguide is considered to be equivalent to the vector sum of magnetic current rings of various radii, ranging from the outer radius of the inner conductor to the inner radius of the outer conductor of the waveguide at the open end. The radiation field is obtained as a vector sum of field components due to individual rings of current. Such a configuration gives rise to multiple narrow radiation beams away from the critical angle. (author)

Switching robust control synthesis for teleoperation via dwell time conditions

NARCIS (Netherlands)

López Martínez, C.A.; van de Molengraft, M.J.G.; Steinbuch, M.; Auvray, M.; Duriez, C.

2014-01-01

Control design for bilateral teleoperation is still an open problem, given that it is desirable to meet a proper balance in the inherent trade-off between transparency and stability. We propose the use of switching robust control, in which smooth switching among controllers is achieved by the

Effects of switching from olanzapine to aripiprazole on the metabolic profiles of patients with schizophrenia and metabolic syndrome: a double-blind, randomized, open-label study [Corrigendum

Directory of Open Access Journals (Sweden)

Wani RA

2015-03-01

Full Text Available Wani RA, Dar MA, Chandel RK, et al Title of paper should have been “Effects of switching from olanzapine to aripiprazole on the metabolic profiles of patients with schizophrenia and metabolic syndrome: a randomized, open-label study”.  Read the original paper 

Characteristics of ion beam and anode plasma in open-quotes Point Pinch Diodeclose quotes

International Nuclear Information System (INIS)

Masugata, K.; Yatsui, K.; Tazima, T.

1993-01-01

Diagnostics and evaluation have been carried out on an ion beam and anode plasma in open-quotes Point Pinch Diode.close quotes Mass spectra of ion beam measured by Thomson-parabola spectrometer have shown that the main component are (1) proton and H 2 + , (2) highly ionized carbon and oxygen ions, and (3) singly ionized C, O and molecules such as CO 2 + , OH + , OH 2 + . X-ray and particle pinhole images have shown the size of the electron beam on the plasma to be less than ∼0.5 mm in diameter, in which fine structures are found with size less than 0.05 mm. A K α satelite line of Al V is observed with crystal spectrograph, which indicates the existence of Al 4+ in the plasma

The Atlas load protection switch

CERN Document Server

Davis, H A; Dorr, G; Martínez, M; Gribble, R F; Nielsen, K E; Pierce, D; Parsons, W M

1999-01-01

Atlas is a high-energy pulsed-power facility under development to study materials properties and hydrodynamics experiments under extreme conditions. Atlas will implode heavy liner loads (m~45 gm) with a peak current of 27-32 MA delivered in 4 mu s, and is energized by 96, 240 kV Marx generators storing a total of 23 MJ. A key design requirement for Atlas is obtaining useful data for 95601130f all loads installed on the machine. Materials response calculations show current from a prefire can damage the load requiring expensive and time consuming replacement. Therefore, we have incorporated a set of fast-acting mechanical switches in the Atlas design to reduce the probability of a prefire damaging the load. These switches, referred to as the load protection switches, short the load through a very low inductance path during system charge. Once the capacitors have reached full charge, the switches open on a time scale short compared to the bank charge time, allowing current to flow to the load when the trigger pu...

Switching from adalimumab to tofacitinib in the treatment of patients with rheumatoid arthritis.

Science.gov (United States)

Genovese, Mark C; van Vollenhoven, Ronald F; Wilkinson, Bethanie; Wang, Lisy; Zwillich, Samuel H; Gruben, David; Biswas, Pinaki; Riese, Richard; Takiya, Liza; Jones, Thomas V

2016-06-23

Tofacitinib is an oral Janus kinase inhibitor for the treatment of rheumatoid arthritis (RA). The aim of this study was to explore the safety and efficacy of open-label tofacitinib following blinded treatment with adalimumab or tofacitinib for moderate to severe RA. Analyses included patients treated with adalimumab 40 mg once every 2 weeks or tofacitinib 10 mg twice daily (BID) with background methotrexate (MTX) in a 12-month randomized study (NCT00853385), who subsequently received tofacitinib 10 mg BID (with/without background MTX) in an open-label extension (NCT00413699). Patients with treatment-related serious adverse events (AEs) and serious or recurrent infections in the index study were excluded from the extension study. Exposure-adjusted incidence rates of safety-related events were assessed in 3-month and 12-month periods in the year before and in the year after switching. Efficacy was assessed 3 months before, at the time of, and 3 months after switching. There were 233 (107 adalimumab to tofacitinib 10 mg BID, 126 blinded to open-label tofacitinib 10 mg BID) patients included in these analyses. Patients in both treatment sequences had similar incidence rates (per 100 patient-years) of discontinuation due to AEs, serious AEs, and serious infections in the year before and in the year after switching. Incidence rates of AEs were increased in the first 3 months after switching compared with the last 3 months before switching in both treatment groups. Switching from either blinded adalimumab or tofacitinib to open-label tofacitinib resulted in numerically higher incidence of responders for signs and symptoms of disease and improved physical function. Treatment can be directly switched from adalimumab to tofacitinib. A similar safety and efficacy profile was seen when patients received open-label tofacitinib after receiving either blinded adalimumab or tofacitinib. ClinicalTrials.gov Identifiers: NCT00853385 , registered 27 February 2009; NCT

Subnanosecond, high voltage photoconductive switching in GaAs

Energy Technology Data Exchange (ETDEWEB)

Druce, R.L.; Pocha, M.D.; Griffin, K.L. (Lawrence Livermore National Lab., CA (USA)); O' Bannon, B.J. (Rockwell International Corp., Anaheim, CA (USA))

1990-01-01

We are conducting research on the switching properties of photoconductive materials to explore their potential for generating high-power microwaves (HPM) and for high rep-rate switching. We have investigated the performance of Gallium Arsenide (GaAs) in linear mode (the conductivity of the device follows the optical pulse) as well as an avalanche-like mode (the optical pulse only controls switch closing). Operating in the linear mode, we have observed switch closing times of less than 200 ps with a 100 ps duration laser pulse and opening times of less than 400 ps at several kV/cm fields using neutron irradiated GaAs. In avalanche and lock-on modes, high fields are switched with lower laser pulse energies, resulting in higher efficiencies; but with measurable switching delay and jitter. We are currently investigating both large area (1 cm{sup 2}) and small area (<1 mm{sup 2}) switches illuminated by AlGaAs laser diodes at 900 nm and Nd:YAG lasers at 1.06 {mu}m.

A Multicell Converter Model of DBD Plasma Discharges

International Nuclear Information System (INIS)

Flores-Fuentes, A. A.; Piedad-Beneitez, A. de la; Pena-Eguiluz, R.; Mercado-Cabrera, A.; Valencia A, R.; Barocio, S. R.; Lopez-Callejas, R.; Godoy-Cabrera, O. G.; Benitez-Read, J. S.; Pacheco-Sotelo, J. O.

2006-01-01

A compact Matlab model of plasma discharges in a DBD reactor consisting of two parallel electrode plates with a small gap and a thin dielectric sheet between them is reported. Its DBD plasma is modelled as a voltage controlled current-source switched on when the voltage across the gap exceeds the breakdown voltage. A three cell voltage-source inverter, configured in half-bridge, has been used as a power supply. This configuration has an excellent performance when operating as an open-loop. The distribution of total energy between a large number of low power converters proofs to be advantageous, allowing an efficient high power drive. Simulation results show that the current source and its output current tend to follow an exponential behaviour. A phenomenological characteristic of the voltage-current behaviour of DBD is then described by power laws with different voltage exponent function values

IGBT: a solid state switch

International Nuclear Information System (INIS)

Chatroux, D.; Maury, J.; Hennevin, B.

1993-01-01

A Copper Vapour Laser Power Supply has been designed using a solid state switch consisting in eighteen Isolated Gate Bipolar Transistors (IGBT), -1200 volts, 400 Amps, each-in parallel. This paper presents the Isolated Gate Bipolar Transistor (IGBTs) replaced in the Power Electronic components evolution, and describes the IGBT conduction mechanism, presents the parallel association of IGBTs, and studies the application of these components to a Copper Vapour Laser Power Supply. The storage capacitor voltage is 820 volts, the peak current of the solid state switch is 17.000 Amps. The switch is connected on the primary of a step-up transformer, followed by a magnetic modulator. The reset of the magnetic modulator is provided by part of the laser reflected energy with a patented circuit. The charging circuit is a resonant circuit with a charge controlled by an IGBT switch. When the switch is open, the inductance energy is free-wheeled by an additional winding and does not extend the charging phase of the storage capacitor. The design allows the storage capacitor voltage to be very well regulated. This circuit is also patented. The electric pulse in the laser has 30.000 Volt peak voltage, 2000 Amp peak current, and is 200 nanoseconds long, for a 200 Watt optical power Copper Vapour Laser

Effects of a precursor plasma on a coaxial-to-radial transition discharge

International Nuclear Information System (INIS)

Enloe, C.L.; Reinovsky, R.E.

1985-01-01

The Quick-Fire series of experiments on the AFWL SHIVA-Star 9.6 megajoule capacitor bank utilizes a coaxial plasma gun as a power conditioning and switching element driving an imploding plasma liner in what is essentially a hollow z-pinch. Initially, the liner is a thin, cylindrical plastic-and-metal foil. Ideally, the foil remains undisturbed until switching action occurs, and steps have been taken to minimize the amount of hot material that is accelerated into the plasma region ahead of the main coaxial discharge. The condition of the foil and the surrounding region prior to switching has been studied both with nitrogen laser shadowgraphy and with a technique which measures the deflection of a helium-neon laser beam due to the presence of density gradients in the switching region. Estimates of the density of precursor plasmas and their effects on foil condition are presented

Improvement of Matrix Converter Drive Reliability by Online Fault Detection and a Fault-Tolerant Switching Strategy

DEFF Research Database (Denmark)

Nguyen-Duy, Khiem; Liu, Tian-Hua; Chen, Der-Fa

2011-01-01

The matrix converter system is becoming a very promising candidate to replace the conventional two-stage ac/dc/ac converter, but system reliability remains an open issue. The most common reliability problem is that a bidirectional switch has an open-switch fault during operation. In this paper, a...

Simultaneous determination of triple therapy for Helicobacter pylori in human plasma by reversed phase chromatography with online wavelength switching

Science.gov (United States)

Ahmed, Sameh; Atia, Noha N.

2015-02-01

The infection of gastric mucosa by Helicobacter pylori (HP) is an essential cofactor in the aetiology of gastroduodenal ulcer and gastric carcinoma. Because of the bacterial resistance, combination therapy containing omeprazole (OME), tinidazole (TNZ) and clarithromycin (CLA) is commonly used for eradication of HP. However, the simultaneous determination of the triple therapy in human plasma was not reported. A simple, reproducible, and selective HPLC method was developed for the simultaneous determination of the triple therapy mixture used for management of HP infections in human plasma. An HPLC procedure based on a liquid-liquid extraction, enrichment of the analytes and subsequent reversed-phase chromatography with UV detection was used. To enable sensitive and selective detection, the method involved the use of online wavelength switching detection, with two different detection wavelengths; 280 nm for detection of OME and TNZ and 210 nm for detection of CLA. Separations were performed on C18 analytical column with acetonitrile-10 mM phosphate buffer of pH = 3.0 at flow rate of 1.0 mL min-1. The linear ranges in human plasma were 0.05-10 μg mL-1 with correlation coefficients >0.9990. The detection limits in human plasma were 0.02-0.07 μg mL-1. Validation parameters were assessed in compliance with US-FDA guidelines. The method proved to be valuable for the therapeutic drug monitoring after oral administration of triple therapy tablets.

Optical processes in the performance and recovery of gas-phase switches

International Nuclear Information System (INIS)

Gundersen, M.

1982-01-01

In this paper several optical processes that may be used to affect gas-phase switch performance and operation are discussed, and approaches using a laser to increase recovery rates of switches are presented. In the latter the laser is used during the recovery phase rather than the conductive or closure phase. This papper suggests that it should be possible to use a low-power laser (e.g., one that is technologically feasible to use as part of a switch) to assist in opening the switch by quenching excited atomic and/or molecular species. The application of laser-induced energy extraction to gas-phase switches is also discussed

The Transistor as Low Level Switch

Energy Technology Data Exchange (ETDEWEB)

Lyden, Anders

1963-10-15

The common collector transistor switch has in the on state with open emitter a certain offset voltage U{sub EK} {approx_equal} -kT/qB{sub N}. This expression is derived in a new, more physical way. It is further shown at which emitter current the current amplification factor B{sub N} should be measured to get a correct value for the above expression. The collector current I at zero collector voltage I{sub K} = I{sub 0}(exp(qU{sub E}/kT) - 1) extremely well. Substitution of I{sub EBO} and I{sub KBO} by I{sub 0} in Eber's and Moll's relations consequently improves these equations and the characteristics of the transistor switch can be better determined. At switching on and off transients appear across the switch. The influence of the 'spike' at switching off can be described by an current I{sub SPIKE} which is easy to calculate. I{sub SPIKE} is approximately dependent only on the base - emitter depletion layer capacitance and the chopper frequency f{sub 0}. Some compensated switches have lower drift than the drift in U{sub EK}. They may, for example, have a temperature drift < 0.2 {mu}V/deg C and a long time drift < 2 {mu}V/week. Some compensated switches also have I{sub SPIKE} < 10{sup -12} f{sub 0}A. The static offset current in the off state can easily be made < 10{sup -12} A.

Improvement of lipoatrophy by switching from efavirenz to lopinavir/ritonavir.

Science.gov (United States)

Rojas, J; Lonca, M; Imaz, A; Estrada, V; Asensi, V; Miralles, C; Domingo, P; Montero, M; del Rio, L; Fontdevila, J; Perez, I; Cruceta, A; Gatell, J M; Arnedo, M; Martínez, E

2016-05-01

To assess whether changes in antiretroviral drugs other than thymidine nucleoside reverse transcriptase inhibitors (NRTI) may have a body fat impact in HIV-infected patients with lipoatrophy. Ninety-six-week phase IV, open-label, multicentre, pilot randomized trial. HIV-infected patients with moderate/severe lipoatrophy at one or more body sites despite long-term thymidine NRTI-free therapy were randomized to continue their efavirenz (EFV)-based antiretroviral regimen or to switch from EFV to lopinavir/ritonavir (LPV/r). The primary endpoint was the absolute change in limb fat mass measured by dual X-ray absorptiometry from baseline to 96 weeks. Changes in other body fat measurements, subjective perception of lipoatrophy, subcutaneous fat gene expression and plasma lipids were also assessed. Thirty-three patients (73% men, median age 52 years) were recruited. At 96 weeks, absolute limb fat mass increased in the LPV/r arm vs. the EFV arm (estimated difference +1082.1 g; 95% CI +63.7 to +2103.5; P = 0.04); this difference remained significant after adjustment by gender, age, fat mass, body mass index and CD4 cell count at baseline. Subjective lipoatrophy perception scores also improved in the LPV/r arm relative to the EFV arm. Adipogenesis, glucose and lipid metabolism, and mitochondrial gene expression increased in the LPV/r arm compared with the EFV arm at 96 weeks. HDL cholesterol decreased in the LPV/r arm relative to the EFV arm. Switching from EFV to LPV/r in HIV-infected patients with lipoatrophy may offer further limb fat gain beyond thymidine NRTI discontinuation, although this strategy decreased plasma HDL cholesterol and caused changes in subcutaneous fat gene expression that may be associated with increased insulin resistance. © 2015 British HIV Association.

Chemical switches and logic gates based on surface modified semiconductors

Energy Technology Data Exchange (ETDEWEB)

Konrad, Szacilowski; Wojciech, Macyk [Jagiellonian Univ., Dept. of Chemistry, Krakow (Poland)

2006-02-15

Photoelectrochemical properties of multicomponent photo-electrodes based on titanium dioxide and cadmium sulfide powders modified with hexacyanoferrate complexes have been examined. Photocurrent responses were recorded as functions of applied potential and photon energy. Surprisingly, the photocurrent can be switched between positive and negative values as a result of potential or photon energy changes. This new effect called Photo Electrochemical Photocurrent Switching (PEPS) opens a possibility of new chemical switches and logic gates construction. Boolean logic analysis and a tentative mechanism of the device are discussed. (authors)

Electroluminescence Spectrum Shift with Switching Behaviour of Diamond Thin Films

Institute of Scientific and Technical Information of China (English)

王小平; 王丽军; 张启仁; 姚宁; 张兵临

2003-01-01

We report a special phenomenon on switching behaviour and the electroluminescence (EL) spectrum shift of doped diamond thin films. Nitrogen and cerium doped diamond thin films were deposited on a silicon substrate by microwave plasma-assisted chemical vapour deposition system and other special techniques. An EL device with a three-layer structure of nitrogen doped diamond/cerium doped diamond/SiO2 thin films was made. The EL device was driven by a direct-current power supply. Its EL character has been investigated, and a switching behaviour was observed. The EL light emission colour of diamond films changes from yellow (590nm) to blue (454 nm) while the switching behaviour appears.

Alterations in plasma phosphorus, red cell 2,3-diphosphoglycerate and P50 following open heart surgery.

Science.gov (United States)

Hasan, R A; Sarnaik, A P; Meert, K L; Dabbagh, S; Simpson, P; Makimi, M

1994-12-01

To evaluate changes in and the correlation between plasma phosphorus, red cell 2,3-diphosphoglycerate (DPG) and adenosine triphosphate (ATP), and P50 in children following heart surgery. Prospective, observational study with factorial design. A pediatric intensive care unit in a university hospital. Twenty children undergoing open heart surgery for congenital heart defects. None. Red cell 2,3-DPG and ATP, P50, plasma phosphorus, and arterial lactate were obtained before and at 1, 8, 16, 24, 48, and 72 hours after surgery. The amount of intravenous fluid and glucose administered, and age of blood utilized were documented. Variables were analyzed by repeated measure analysis of variance followed by paired t-tests. To investigate the relationship between variables at each time point, scatterplot matrices and correlation coefficients were obtained. There was a reduction in plasma phosphorus, red cell 2,3-DPG, and P50 and an increase in arterial lactate at 1, 8, 16, 24, 48, and 72 hours after surgery. Red cell 2,3-DPG correlated with P50 at 1, 8 and 16 hours. The decrease in the plasma phosphorus correlated with the amounts of intravenous fluid and glucose administered on the day of surgery and on the first and second postoperative days. The age of the blood utilized correlated with the decrease in red cell 2,3-DPG on the day of surgery. Reduction in red cell 2,3-DPG, P50, and plasma phosphorus occurs after open heart surgery in children. These changes can potentially contribute to impaired oxygen utilization in the postoperative period, when adequacy of tissue oxygenation is critical.

Subnanosecond photoconductive switching in GaAs

Energy Technology Data Exchange (ETDEWEB)

Druce, R.L.; Pocha, M.D.; Griffin, K.L.

1991-04-01

We are conducting research in photoconductive switching for the purpose of generating microwave pulses with amplitudes up to 50 kV. This technology has direct application to impulse radar and HPM sources. We are exploiting the very fast recombination rates of Gallium Arsenide (GaAs) to explore the potential of GaAs as an on-off switch when operating in the linear mode (the linear mode is defined such that one carrier pair is generated for each photon absorbed). In addition, we are exploring the potential GaAs to act as a closing switch in ``avalanche`` mode at high fields. We have observed switch closing times of less than 200 psec with a 100 psec duration laser pulse and opening times of less than 400 psec with neutron irradiated GaAs at fields of tens of kV/cm. If the field is increased and the laser energy decreased, the laser can be used to trigger photoconductive switches into ``avalanche`` mode of operation in which carrier multiplication occurs. This mode of operation is quite promising since the switches close in less than 1 nsec while realizing significant energy gain (ratio of electrical energy in the pulse to optical trigger energy). We are currently investigating both large area (1 sq cm) and small area (< 1 sq mm) switches illuminated by GaAlAs laser diodes at 900 nm and Nd:YAG lasers at 1.06 micrometers. Preliminary results indicate that the closing time of the avalanche switches depends primarily on the material properties of the devices with closing times of 300--1300 psec at voltages of 6--35 kV. We will present experimental results for linear, lock on and avalanche mode operation of GaAs photoconductive switches and how these pulses may be applied to microwave generation. 3 refs.

Subnanosecond photoconductive switching in GaAs

Energy Technology Data Exchange (ETDEWEB)

Druce, R.L.; Pocha, M.D.; Griffin, K.L.

1991-04-01

We are conducting research in photoconductive switching for the purpose of generating microwave pulses with amplitudes up to 50 kV. This technology has direct application to impulse radar and HPM sources. We are exploiting the very fast recombination rates of Gallium Arsenide (GaAs) to explore the potential of GaAs as an on-off switch when operating in the linear mode (the linear mode is defined such that one carrier pair is generated for each photon absorbed). In addition, we are exploring the potential GaAs to act as a closing switch in avalanche'' mode at high fields. We have observed switch closing times of less than 200 psec with a 100 psec duration laser pulse and opening times of less than 400 psec with neutron irradiated GaAs at fields of tens of kV/cm. If the field is increased and the laser energy decreased, the laser can be used to trigger photoconductive switches into avalanche'' mode of operation in which carrier multiplication occurs. This mode of operation is quite promising since the switches close in less than 1 nsec while realizing significant energy gain (ratio of electrical energy in the pulse to optical trigger energy). We are currently investigating both large area (1 sq cm) and small area (< 1 sq mm) switches illuminated by GaAlAs laser diodes at 900 nm and Nd:YAG lasers at 1.06 micrometers. Preliminary results indicate that the closing time of the avalanche switches depends primarily on the material properties of the devices with closing times of 300--1300 psec at voltages of 6--35 kV. We will present experimental results for linear, lock on and avalanche mode operation of GaAs photoconductive switches and how these pulses may be applied to microwave generation. 3 refs.

Subnanosecond photoconductive switching in GaAs

Energy Technology Data Exchange (ETDEWEB)

Druce, R.L.; Pocha, M.D.; Griffin, K.L.

1990-01-01

We are conducting research in photoconductive switching for the purpose of generating microwave pulses with amplitudes up to 50 kV. This technology has direct application to impulse radar and HPM sources. We are exploiting the very fast recombination rates of Gallium Arsenide (GaAs) to explore the potential of GaAs as an on-off switch when operating in the linear mode (the linear mode is defined such that one carrier pair is generated for each photon absorbed). In addition, we are exploring the potential of GaAs to act as a closing switch in avalanche'' mode at high fields. We have observed switch closing times of less than 200 psec with 100 psec duration laser pulse and opening times of less than 400 psec with neutron irradiated GaAs at fields of tens of kV/cm. If the field is increased and the laser energy decreased, the laser can be used to trigger photoconductive switches into an avalanche'' mode of operation in which carrier multiplication occurs. This mode of operation is quite promising since the switches close in less than 1 nsec while realizing significant energy gain (ratio of electrical energy in the pulse to optical trigger energy). We are currently investigating both large are (1 sq cm) and small area (<1 sq mm) switches illuminated by GaAlAs laser diodes at 900 nm and Nd:YAG lasers at 1.06 micrometers. Preliminary results indicate that the closing time of the avalanche switches depends primarily on the material properties of the devices with closing times of 300--1300 psec at voltages of 6-35 kV. We will present experimental results for linear, lock on and avalanche mode operation of GaAs photoconductive switches and how these pulses may be applied to microwave generation. 3 refs., 11 figs.

Subnanosecond photoconductive switching in GaAs

Science.gov (United States)

Druce, R. L.; Pocha, M. D.; Griffin, K. L.

1991-04-01

We are conducting research in photoconductive switching for the purpose of generating microwave pulses with amplitudes up to 50 kV. This technology has direct application to impulse radar and HPM sources. We are exploiting the very fast recombination rates of Gallium Arsenide (GaAs) to explore the potential of GaAs as an on-off switch when operating in the linear mode (the linear mode is defined such that one carrier pair is generated for each photon absorbed). In addition, we are exploring the potential GaAs to act as a closing switch in 'avalanche' mode at high fields. We have observed switch closing times of less than 200 psec with a 100 psec duration laser pulse and opening times of less than 400 psec with neutron irradiated GaAs at fields of tens of kV/cm. If the field is increased and the laser energy decreased, the laser can be used to trigger photoconductive switches into 'avalanche' mode of operation in which carrier multiplication occurs. This mode of operation is quite promising since the switches close in less than 1 nsec while realizing significant energy gain (ratio of electrical energy in the pulse to optical trigger energy). We are currently investigating both large area (1 sq cm) and small area (less than 1 sq mm) switches illuminated by GaAlAs laser diodes at 900 nm and Nd:YAG lasers at 1.06 micrometers. Preliminary results indicate that the closing time of the avalanche switches depends primarily on the material properties of the devices with closing times of 300-1300 psec at voltages of 6-35 kV. We will present experimental results for linear, lock on, and avalanche mode operation of GaAs photoconductive switches and how these pulses may be applied to microwave generation.

Magnetic particle separation using controllable magnetic force switches

International Nuclear Information System (INIS)

Wei Zunghang; Lee, C.-P.; Lai, M.-F.

2010-01-01

Magnetic particle separation is very important in biomedical applications. In this study, a magnetic particle microseparator is proposed that uses micro magnets to produce open/closed magnetic flux for switching on/off the separation. When all magnets are magnetized in the same direction, the magnetic force switch for separation is on; almost all magnetic particles are trapped in the channel side walls and the separation rate can reach 95%. When the magnetization directions of adjacent magnets are opposite, the magnetic force switch for separation is off, and most magnetic particles pass through the microchannel without being trapped. For the separation of multi-sized magnetic particles, the proposed microseparator is numerically demonstrated to have high separation rate.

Streaming metal plasma generation by vacuum arc plasma guns

International Nuclear Information System (INIS)

MacGill, R.A.; Dickinson, M.R.; Anders, A.; Monteiro, O.R.; Brown, I.G.

1998-01-01

We have developed several different embodiments of repetitively pulsed vacuum arc metal plasma gun, including miniature versions, multicathode versions that can produce up to 18 different metal plasma species between which one can switch, and a compact high-duty cycle well-cooled version, as well as a larger dc gun. Plasma guns of this kind can be incorporated into a vacuum arc ion source for the production of high-energy metal ion beams, or used as a plasma source for thin film formation and for metal plasma immersion ion implantation and deposition. The source can also be viewed as a low-energy metal ion source with ion drift velocity in the range 20 - 200 eV depending on the metal species used. Here we describe the plasma sources that we have developed, the properties of the plasma generated, and summarize their performance and limitations. copyright 1998 American Institute of Physics

Electro- and photochemical switching of dithienylethene self-assembled monolayers on gold electrodes

DEFF Research Database (Denmark)

Browne, W.R.; Kudernac, T.; Katsonis, N.

2008-01-01

forms of the dithienylethene SAMs is examined and found to be sensitive to the molecular structure of the switch. For the three dithienylethenes, the electrochemical behavior with respect to electrochemical ring opening/closing is retained in the SAMs. In contrast, a marked dependence on the nature...... of the anchoring group is observed upon immobilization in terms of the retention of the photochemical properties observed in solution. For the meta-thiophenol anchor both photochemical ring opening and closing are observed in the SAM, while for the thienyl-thiol-anchored switches the photochemically properties...

The Maryland Centrifugal Experiment (MCX): Centrifugal Confinement and Velocity Shear Stabilization of Plasmas in Shaped Open Magnetic Systems

International Nuclear Information System (INIS)

Hassam, Adil; Ellis, Richard F.

2012-01-01

The Maryland Centrifugal Experiment (MCX) Project has investigated the concepts of centrifugal plasma confinement and stabilization of instabilities by velocity shear. The basic requirement is supersonic plasma rotation about a shaped, open magnetic field. Overall, the MCX Project attained three primary goals that were set out at the start of the project. First, supersonic rotation at Mach number up to 2.5 was obtained. Second, turbulence from flute interchange modes was found considerably reduced from conventional. Third, plasma pressure was contained along the field, as evidenced by density drops of x10 from the center to the mirror throats.

Tyr66 acts as a conformational switch in the closed-to-open transition of the SHP-2 N-SH2-domain phosphotyrosine-peptide binding cleft

Directory of Open Access Journals (Sweden)

MacKerell Alexander D

2007-03-01

Full Text Available Abstract Background The N-terminal SH2 domain (N-SH2 of the non-receptor tyrosine phosphatase SHP-2 is involved both in localization of SHP-2 by recognition of phosphotyrosine (pY peptides and self-inhibition of SHP-2 phosphatase activity through the formation of a protein – protein interface with the phosphatase domain. Mutations that disrupt this interface break the coupling between pY-peptide binding cleft conformation and self-inhibition, thereby increasing both SHP-2 phosphatase activity and pY-peptide binding affinity, and are associated with the congenital condition Noonan syndrome and various pediatric leukemias. To better characterize the molecular process involved in N-SH2 pY-dependent binding, we have applied explicit-solvent molecular dynamics simulations to study the closed-to-open transition of the N-SH2 pY-peptide binding cleft. Results The existence of stable conformations in the left-handed helical and the extended regions of Tyr66 φ/ψ space prevent rapid interconversion of the backbone and create a conformational switch such that Tyr66 in a left-handed helical backbone conformation results in an open cleft and in an extended backbone conformation results in a closed cleft. The stable conformations arise from deep, well-localized free-energy minima in the left-handed helical and extended regions of the Tyr66 φ/ψ map. Changing the Tyr66 backbone conformation from extended to left-handed helical induces a closed-to-open transition in the cleft, and the reverse change in backbone conformation induces the reverse, open-to-closed transition. In the open-cleft state, weak solvent-exposed interactions involving the sidechains of Tyr66, Asp40, Lys55, and Gln57 serve to anchor the Tyr66 sidechain to the surface of the protein and away from the binding cleft entrance, thereby facilitating pY-peptide access to the binding cleft. Conclusion The simulations point to a regulatory role for Tyr66 and surrounding residues in SHP-2 function

Interrupter and hybrid-switch testing for fusion devices

International Nuclear Information System (INIS)

Parsons, W.M.; Warren, R.W.; Honig, E.M.; Lindsay, J.D.G.; Bellamo, P.; Cassel, R.L.

1979-01-01

This paper discusses recent and ongoing switch testing for fusion devices. The first part describes testing for the TFTR ohmic-heating circuit. In this set of tests, which simulated the stresses produced during a plasma initiation pulse, circuit breakers were required to interrupt a current of 24 kA with an associated recovery voltage of 25 kV. Two interrupter systems were tested for over 1000 operations each, and both appear to satisfy TFTR requirements. The second part discusses hybrid-switch development for superconducting coil protection. These switching systems must be capable of carrying large currents on a continuous basis as well as performing interruption duties. The third part presents preliminary results on an early-counterpulse technique applied to vacuum interrupters. Implementation of this technique has resulted in large increases in interruptible current as well as a marked reduction in contact erosion

Complex (dusty) plasmas: Current status, open issues, perspectives

International Nuclear Information System (INIS)

Fortov, V.E.; Ivlev, A.V.; Khrapak, S.A.; Khrapak, A.G.; Morfill, G.E.

2005-01-01

The field of complex (dusty) plasmas-low-temperature plasmas containing charged microparticles-is reviewed: The major types of experimental complex plasmas are briefly discussed. Various elementary processes, including grain charging in different regimes, interaction between charged particles, and momentum exchange between different species are investigated. The major forces on microparticles and features of the particle dynamics in complex plasmas are highlighted. An overview of the wave properties in different phase states, as well as recent results on the phase transitions between different crystalline and liquid states are presented. Fluid behaviour of complex plasmas and the onset of cooperative phenomena are discussed. Properties of the magnetized complex plasmas and plasmas with nonspherical particles are briefly mentioned. In conclusion, possible applications of complex plasmas, interdisciplinary aspects, and perspectives are discussed

Observation of enhanced electric field in an RF-plugged sheet plasma in the RFC-XX-M open-ended machine

International Nuclear Information System (INIS)

Oda, T.; Takiyama, K.; Kadota, K.

1987-12-01

We report nonperturbing observation of the electric field in the sheet plasma for RF end-plugging on the RFC XX-M open-ended machine by using the Stark effect with a combined technique of beam-probe and laser-induced fluorescence. Under the optimum condition for the RF plugging, enhanced electric field is found in the sheet plasma by about 2.5 times with respect to the electric field when no plasma is produced. The field spatial profile is also measured, which is discussed in connection with the electrostatic eigenmode. (author)

Microwave interferometry of PEOS plasma sources

International Nuclear Information System (INIS)

Weber, B.V.; Commisso, R.J.; Goodrich, P.J.; Hinshelwood, D.D.; Neri, J.M.

1988-01-01

A 70 GHz microwave interferometer is used to measure the electron density for various configurations of sources used in plasma erosion opening switch (PEOS) experiments. The interferometer is a phase quadrature system, so the density can be measured as a function of time without ambiguity. Measurements have been made for carbon guns and flashboards driven by a .6 μF. 25 kV capacitor. The plasma density from a gun rises to its peak value in about 10 μs. Then decays in the next 40 μs. A metal screen placed between the gun and the microwave beam attenuates the plasma density by a factor greater than the geometrical transparency of the screen. Density measurements as a function of distance from the gun are analyzed to give the plasma spatial dependence, and the particle flux density and flow velocity are calculated from the continuity equation. Density values used to model previous PEOS experiments are comparable to the values measured here. The flashboard sources produce a denser, faster plasma that is more difficult to diagnose with the interferometer than the gun plasma because of refractive bending of the microwave beam. Reducing the plasma length reduces the refractive bending enough that some measurements are possible. Direct comparison with Gamble II PEOS experiments that used these flashboard sources may not be possible at this frequency because of refraction, but estimates based on measurements at larger distances give reasonable agreement with values used to model these experiments. Other measurements that will be presented include the effects of plasma flow against metal walls, effects of changing the driving current waveform, measurements made in actual experimental configurations and comparisons with Faraday cup and electric probe measurements

New fast switches for the Tore Supra ohmic heating circuit

International Nuclear Information System (INIS)

Zunino, K.; Bruneth, J.; Cara, P.; Louart, A.; Santagiustina, A.; Emelyanova, I.; Filippov, F.; Mikailov, N.

2003-01-01

The Tore-Supra ohmic heating circuit is equipped with four fast make switches and one fast opening switch. After many years of operation, it became necessary to substitute this equipment by modern components with similar ratings. An extensive research has been undertaken to find fast switches able to withstand more than 2500 operations per year without maintenance, at a make current of 54 kA, a voltage of 12 kV and with a closing time of less than 15 ms. At the end of the investigation, it was decided to replace the old components by fast mechanical switches proposed by the Efremov Institute and based on a prototype developed for ITER. This paper presents the technical requirements and the characteristics of the switches and describes the operational experience gained with these components during operating campaigns of 2002 and 2003. (authors)

High power switches for ion induction linacs

International Nuclear Information System (INIS)

Humphries, S. Jr.; Savage, M.; Saylor, W.B.

1985-01-01

The success of linear induction ion accelerators for accelerator inertial fusion (AIF) applications depends largely on innovations in pulsed power technology. There are tight constraints on the accuracy of accelerating voltage waveforms to maintain a low momentum spread. Furthermore, the non-relativistic ion beams may be subject to a klystron-like interaction with the accelerating cavities leading to enhanced momentum spread. In this paper, the author describe a novel high power switch with a demonstrated ability to interrupt 300 A at 20 kV in less than 60 ns. The switch may allow the replacement of pulse modulators in linear induction accelerators with hard tube pulsers. A power system based on a hard tube pulser could solve the longitudinal instability problem while maintaining high energy transfer efficiency. The problem of longitudinal beam control in ion induction linacs is reviewed in Section 2. Section 3 describes the principles of the plasma flow switch. Experimental results are summarized in Section 4

High power switches for ion induction linacs

International Nuclear Information System (INIS)

Humphries, S.; Savage, M.; Saylor, W.B.

1985-01-01

The success of linear induction ion accelerators for accelerator inertial fusion (AIF) applications depends largely on innovations in pulsed power technology. There are tight constraints on the accuracy of accelerating voltage waveforms to maintain a low momentum spread. Furthermore, the non-relativistic ion beams may be subject to a klystronlike interaction with the accelerating cavities, leading to enhanced momentum spread. In this paper, we describe a novel high power switch with a demonstrated ability to interrupt 300 A at 20 kV in less than 60 ns. The switch may allow the replacement of pulse modulators in linear induction accelerators with hard tube pulsers. A power system based on a hard tube pulser could solve the longitudinal instability problem while maintaining high energy transfer efficiency. The problem of longitudinal beam control in ion induction linacs is reviewed in Section 2. Section 3 describes the principles of the plasma flow switch. Experimental results are summarized in Section 4

Plasma Diagnostics by Microwave Interferometry in MHD Channels with the Aid of an Open Waveguide

Energy Technology Data Exchange (ETDEWEB)

Muenkel, J. [Rheinische-Westfalische Technische Hochschule Aachen, Federal Republic of Germany (Germany)

1966-10-15

Plasma diagnostics of a novel kind, using microwave interferometry, is described. Use is made of an open non-conventional waveguide in the test path of the microwave bridge. Guiding the microwave has several advantages over free transmission of the test h.f. beam between two horn antennas if there are small plasma streams bounded by ceramics and metals as in the case of MHD channels. There are less unknown and uncontrolled disturbances of the electromagnetic waves introduced by the boundaries. On the other hand most guiding structures disturb the homogeneity of the streaming plasma (cf. arrangements with Lecher wires, dielectric rods, etc.); the waveguide used here does not do so. This waveguide, a so-called groove guide, consists of two parallel metal plates or bands with a shallow axially-directed groove in each. The plasma stream to be tested flows between these plates in a direction perpendicular to the direction of propagation of the microwaves. The groove guide has properties similar to the ideal parallel-plate guide with infinite side wards extension, but the energy flow is concentrated in the middle region by the grooves. An approximate analysis, the transverse resonance analysis, has been used to calculate the field distribution and propagation characteristics of the guide. Because of the cross-sectional dimensions of the MHD channel in question (height 16 mm) and the wavelength (4 mm) chosen, considering the expected electron density, the groove guide had to be built for use in an oversized quasi-optical technique. The transition from rectangular (hollow pipe) guide to the open guide is done in two steps. With a good knowledge of the groove guide data and an appropriate theory of propagation of electromagnetic waves in ionized media, measuring phase shift and additional damping of the microwaves by introduction of the ionized gas allows the electron density and collision frequency, two of the most important plasma parameters, to be evaluated. The system

Protection and switching system for the RFX power supply

International Nuclear Information System (INIS)

Browning, J.L.; Gray, J.W.; Mace, T.A.; Varley, G.L.

1986-01-01

The RFX toroidal field power supply comprises a large 4.8MJ (max) modular capacitor bank and four 14MW AC/DC converter flat-top power supply modules. The high fault level associated with the capacitor banks presents a problem in the design of the switching system, since mistiming could produce large currents in the flat-top supplies. The poloidal circuit consists of four groups of magnetising windings connected in series, each with its own flat-top convertor supply and opening switch transfer system. The flat-top converter supplies are needed when the transfer voltage has fallen from approximately 40kV to 1kV. Solutions to the problem of designing a fault-tolerant system which presents no danger to the flat-top converters are described in the paper. The adopted methods make use of hybrid ignitron/mechanical switches to give the required combination of switching speed and current carrying capacity, together with careful attention to the circuit layout of different switching elements. (author)

Sharing Water-related Information to Tackle Changes in the Hydrosphere - for Operational Needs (SWITCH-ON)

Science.gov (United States)

Arheimer, Berit

2015-04-01

Recently, a collaborative EU project started called SWITCH-ON (EU FP7 project No 603587) coordinated by SMHI to support the INSPIRE directive and the Open Data Strategy. The overall goal of the project is to establish a "one-stop-shop" web portal for easy access to European water information. The project will use open data, provide infrastructure for sharing and collaboration, and add value to society and research by repurposing and refining data from various sources. The SWITCH-ON project http://www.water-switch-on.eu/ will establish new forms of water research and facilitate the development of new products and services based on principles of sharing and community building in the water society. The SWITCH-ON objectives are to use open data for implementing: 1) an innovative spatial information platform (SIP) to find, bind, transform and publish data, 2) entirely new forms of collaborative research organised in a Virtual Water-Science Laboratory, open for any research group, 3) fourteen new operational products for water management and awareness, 4) outreach facilities for new water business and knowledge in line with the Europe's smart growth and environmental objectives. This poster will describe the overall project goals and especially the recent progress on developing a Virtual Water-Science Laboratory. Contact: waterswitchon@gmail.com

Q-Switching in a Neodymium Laser

Science.gov (United States)

Holgado, Warein; Sola, Inigo J.; Jarque, Enrique Conejero; Jarabo, Sebastian; Roso, Luis

2012-01-01

We present a laboratory experiment for advanced undergraduate or graduate laser-related classes to study the performance of a neodymium laser. In the experiment, the student has to build the neodymium laser using an open cavity. After that, the cavity losses are modulated with an optical chopper located inside, so the Q-switching regime is…

Characterization and switching performance of electron-beam controlled discharges

International Nuclear Information System (INIS)

Lowry, J.F.; Kline, L.E.; Heberlein, J.V.R.

1986-01-01

The electron-beam sustained discharge switch is an attractive concept for repetitive pulsed power switching because it has a demonstrated capability to interrupt direct current and because it is inherently scalable. The authors report on experiments with this type of switch in a 4-kV dc circuit. A wire-ion-plasma (WIP) electron-beam (e-beam) gun is used to irradiate and sustain a switch discharge with a 100-cm/sup 2/ cross-sectional area in l atm of N/sub 2/ or CH/sub 4/. Interruption of 8-10-μs pulses of up to 1.9 kA, and of 100-μs pulses of 150 A has been demonstrated in methane, and interruption against higher recovery voltages (11 kV) has been performed at 1.2 kA by adding series inductance to the circuit. These values represent power supply limitations rather than limitations of the switch itself. A comparison of the measured discharge characteristics with theoretical predictions shows that the measured switch conductivities are higher than the predicted values for given e-beam current values. A qualitative explanation for this observation is offered by considering the effects of electron reflection from the discharge anode and of nonlinear paths for the beam electrons across the discharge gap. The authors conclude that the switching performance of the e-beam controlled discharge switch corresponds to its design parameters, and that for a given switch size a lower voltage drop during the on time can be expected compared with the voltage drop predicted by previously published theory

Low temperature grown GaNAsSb: A promising material for photoconductive switch application

Energy Technology Data Exchange (ETDEWEB)

Tan, K. H.; Yoon, S. F.; Wicaksono, S.; Loke, W. K.; Li, D. S. [School of Electrical and Electronic Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798 (Singapore); Saadsaoud, N.; Tripon-Canseliet, C. [Laboratoire d' Electronique et Electromagnétisme, Pierre and Marie Curie University, 4 Place Jussieu, 75005 Paris (France); Lampin, J. F.; Decoster, D. [Institute of Electronics, Microelectronics and Nanotechnology (IEMN), UMR CNRS 8520, Universite des Sciences et Technologies de Lille, BP 60069, 59652 Villeneuve d' Ascq Cedex (France); Chazelas, J. [Thales Airborne Systems, 2 Avenue Gay Lussac, 78852 Elancourt (France)

2013-09-09

We report a photoconductive switch using low temperature grown GaNAsSb as the active material. The GaNAsSb layer was grown at 200 °C by molecular beam epitaxy in conjunction with a radio frequency plasma-assisted nitrogen source and a valved antimony cracker source. The low temperature growth of the GaNAsSb layer increased the dark resistivity of the switch and shortened the carrier lifetime. The switch exhibited a dark resistivity of 10{sup 7} Ω cm, a photo-absorption of up to 2.1 μm, and a carrier lifetime of ∼1.3 ps. These results strongly support the suitability of low temperature grown GaNAsSb in the photoconductive switch application.

Assessment of strategies for switching patients from olanzapine to risperidone: A randomized, open-label, rater-blinded study

Directory of Open Access Journals (Sweden)

Berry Sally A

2008-06-01

Full Text Available Abstract Background In clinical practice, physicians often need to change the antipsychotic medications they give to patients because of an inadequate response or the presence of unacceptable or unsafe side effects. However, there is a lack of consensus in the field as to the optimal switching strategy for antipsychotics, especially with regards to the speed at which the dose of the previous antipsychotic should be reduced. This paper assesses the short-term results of strategies for the discontinuation of olanzapine when initiating risperidone. Methods In a 6-week, randomized, open-label, rater-blinded study, patients with schizophrenia or schizoaffective disorder, on a stable drug dose for more than 30 days at entry, who were intolerant of or exhibiting a suboptimal symptom response to more than 30 days of olanzapine treatment, were randomly assigned to the following switch strategies (common risperidone initiation scheme; varying olanzapine discontinuation: (i abrupt strategy, where olanzapine was discontinued at risperidone initiation; (ii gradual 1 strategy, where olanzapine was given at 50% entry dose for 1 week after risperidone initiation and then discontinued; or (iii gradual 2 strategy, where olanzapine was given at 100% entry dose for 1 week, then at 50% in the second week, and then discontinued. Results The study enrolled 123 patients on stable doses of olanzapine. Their mean age was 40.3 years and mean (± standard deviation (SD baseline Positive and Negative Syndrome Scale (PANSS total score of 75.6 ± 11.5. All-cause treatment discontinuation was lowest (12% in the group with the slowest olanzapine dose reduction (gradual 2 and occurred at half the discontinuation rate in the other two groups (25% in abrupt and 28% in gradual 1. The relative risk of early discontinuation was 0.77 (confidence interval 0.61–0.99 for the slowest dose reduction compared with the other two strategies. After the medication was changed, improvements at

A pH Switch Regulates the Inverse Relationship between Membranolytic and Chaperone-like Activities of HSP-1/2, a Major Protein of Horse Seminal Plasma.

Science.gov (United States)

Kumar, C Sudheer; Swamy, Musti J

2016-07-05

HSP-1/2, a major protein of horse seminal plasma binds to choline phospholipids present on the sperm plasma membrane and perturbs its structure by intercalating into the hydrophobic core, which results in an efflux of choline phospholipids and cholesterol, an important event in sperm capacitation. HSP-1/2 also exhibits chaperone-like activity (CLA) in vitro and protects target proteins against various kinds of stress. In the present study we show that HSP-1/2 exhibits destabilizing activity toward model supported and cell membranes. The membranolytic activity of HSP-1/2 is found to be pH dependent, with lytic activity being high at mildly acidic pH (6.0-6.5) and low at mildly basic pH (8.0-8.5). Interestingly, the CLA is also found to be pH dependent, with high activity at mildly basic pH and low activity at mildly acidic pH. Taken together the present studies demonstrate that the membranolytic and chaperone-like activities of HSP-1/2 have an inverse relationship and are regulated via a pH switch, which is reversible. The higher CLA observed at mildly basic pH could be correlated to an increase in surface hydrophobicity of the protein. To the best of our knowledge, this is the first study reporting regulation of two different activities of a chaperone protein by a pH switch.

Correlation between plasma homovanillic acid levels and the response to atypical antipsychotics in male patients with schizophrenia.

Science.gov (United States)

Kaneda, Yasuhiro; Kawamura, Ichiro; Ohmori, Tetsuro

2005-01-01

The authors investigated the effects of atypical antipsychotic drugs-olanzapine, perospirone, and quetiapine-on plasma homovanillic acid (pHVA) in male patients with chronic schizophrenia. In this prospective, open-label study, the subjects were 30 inpatients who were diagnosed according to the Diagnostic and Statistical Manual of Mental Disorders, 4th edition, criteria for schizophrenia. The authors switched patients from typical antipsychotic drugs to olanzapine, perospirone, or quetiapine. Each patient gave informed consent for the research. pHVA was assessed before and after switching medications. After the switch, the authors found a significant improvement in psychotic symptoms, nonsignificant improvement in extrapyramidal symptoms, and a nonsignificant reduction in pHVA. In addition, the baseline pHVA correlated positively with the score changes from baseline in the Brief Psychiatric Rating Scale (BPRS) total, positive, and negative symptoms in the group with a whole sample and in the olanzapine-treated group, and with the score changes in the BPRS total and positive symptoms in the quetiapine-treated group. Our findings indicated that the preswitching pHVA levels could be used to predict changes in the psychotic symptoms of male patients with chronic schizophrenia when switching to atypical antipsychotic drugs.

EXPERIMENTAL STUDY OF SHOCK WAVE DYNAMICS IN MAGNETIZED PLASMAS

International Nuclear Information System (INIS)

Podder, Nirmol K.

2009-01-01

In this four-year project (including one-year extension), the project director and his research team built a shock-wave-plasma apparatus to study shock wave dynamics in glow discharge plasmas in nitrogen and argon at medium pressure (1-20 Torr), carried out various plasma and shock diagnostics and measurements that lead to increased understanding of the shock wave acceleration phenomena in plasmas. The measurements clearly show that in the steady-state dc glow discharge plasma, at fixed gas pressure the shock wave velocity increases, its amplitude decreases, and the shock wave disperses non-linearly as a function of the plasma current. In the pulsed discharge plasma, at fixed gas pressure the shock wave dispersion width and velocity increase as a function of the delay between the switch-on of the plasma and shock-launch. In the afterglow plasma, at fixed gas pressure the shock wave dispersion width and velocity decrease as a function of the delay between the plasma switch-off and shock-launch. These changes are found to be opposite and reversing towards the room temperature value which is the initial condition for plasma ignition case. The observed shock wave properties in both igniting and afterglow plasmas correlate well with the inferred temperature changes in the two plasmas

Experimental investigation of plasma relaxation using a compact coaxial magnetized plasma gun in a background plasma

Science.gov (United States)

Zhang, Yue; Lynn, Alan; Gilmore, Mark; Hsu, Scott; University of New Mexico Collaboration; Los Alamos National Laboratory Collaboration

2013-10-01

A compact coaxial plasma gun is employed for experimental studies of plasma relaxation in a low density background plasma. Experiments are being conducted in the linear HelCat device at UNM. These studies will advance the knowledge of basic plasma physics in the areas of magnetic relaxation and space and astrophysical plasmas, including the evolution of active galactic jets/radio lobes within the intergalactic medium. The gun is powered by a 120pF ignitron-switched capacitor bank which is operated in a range of 5-10 kV and ~100 kA. Multiple diagnostics are employed to investigate plasma relaxation process. Magnetized Argon plasma bubbles with velocities ~1.2Cs and densities ~1020 m-3 have been achieved. Different distinct regimes of operation with qualitatively different dynamics are identified by fast CCD camera images, with the parameter determining the operation regime. Additionally, a B-dot probe array is employed to measure the spatial toroidal and poloidal magnetic flux evolution to identify detached plasma bubble configurations. Experimental data and analysis will be presented.

Spectrographic temperature measurement of a high power breakdown arc in a high pressure gas switch

Energy Technology Data Exchange (ETDEWEB)

Yeckel, Christopher; Curry, Randy [Department of Computer and Electrical Engineering, Center for Physical and Power Electronics, University of Missouri--Columbia, Columbia, Missouri 65211 (United States)

2011-09-15

A procedure for obtaining an approximate temperature value of conducting plasma generated during self-break closure of a RIMFIRE gas switch is described. The plasma is in the form of a breakdown arc which conducts approximately 12 kJ of energy in 1 {mu}s. A spectrographic analysis of the trigger-section of the 6-MV RIMFIRE laser triggered gas switch used in Sandia National Laboratory's ''Z-Machine'' has been made. It is assumed that the breakdown plasma has sufficiently approached local thermodynamic equilibrium allowing a black-body temperature model to be applied. This model allows the plasma temperature and radiated power to be approximated. The gas dielectric used in these tests was pressurized SF{sub 6}. The electrode gap is set at 4.59 cm for each test. The electrode material is stainless steel and insulator material is poly(methyl methacrylate). A spectrum range from 220 to 550 nanometers has been observed and calibrated using two spectral irradiance lamps and three spectrograph gratings. The approximate plasma temperature is reported.

Access control mechanism of wireless gateway based on open flow

Science.gov (United States)

Peng, Rong; Ding, Lei

2017-08-01

In order to realize the access control of wireless gateway and improve the access control of wireless gateway devices, an access control mechanism of SDN architecture which is based on Open vSwitch is proposed. The mechanism utilizes the features of the controller--centralized control and programmable. Controller send access control flow table based on the business logic. Open vSwitch helps achieve a specific access control strategy based on the flow table.

Mode switching control of dual-evaporator air-conditioning systems

International Nuclear Information System (INIS)

Lin, J.-L.; Yeh, T.-J.

2009-01-01

Modern air-conditioners incorporate variable-speed compressors and variable-opening expansion valves as the actuators for improving cooling performance and energy efficiency. These actuators have to be properly feedback-controlled; otherwise the systems may exhibit even poorer performance than the conventional machines which use fixed-speed compressors and mechanical expansion valves. Particularly for an air-conditioner with multiple evaporators, there are occasions that the machine is operated in a mode that only selected evaporator(s) is(are) turned on, and switching(s) between modes occurs(occur) during the control process. In this case, one needs to have more carefully designed control and switching strategies to ensure the system performance. In this paper, a framework for mode switching control of the dual-evaporator air-conditioning (DEAC) system is proposed. The framework is basically an integration of a controller and a dynamic compensator. The controller, which possesses the flow-distribution capability and assumes both evaporators are on throughout the control process, is intended to provide nominal performance. While mode switching is achieved by varying the reference settings in the controller, the dynamic compensator is used to improve the transient responses immediately after the switching. Experiments indicate that the proposed framework can achieve satisfactory indoor temperature regulation and provide bumpless switching between different modes of operation.

Modeling and Analysis of Modal Switching in Networked Transport Systems

International Nuclear Information System (INIS)

Hante, Falk M.; Leugering, Guenter; Seidman, Thomas I.

2009-01-01

We consider networked transport systems defined on directed graphs: the dynamics on the edges correspond to solutions of transport equations with space dimension one. In addition to the graph setting, a major consideration is the introduction and propagation of discontinuities in the solutions when the system may discontinuously switch modes, naturally or as a hybrid control. This kind of switching has been extensively studied for ordinary differential equations, but not much so far for systems governed by partial differential equations. In particular, we give well-posedness results for switching as a control, both in finite horizon open loop operation and as feedback based on sensor measurements in the system

Re-appraisal and extension of the Gratton-Vargas two-dimensional analytical snowplow model of plasma focus evolution in the context of contemporary research

International Nuclear Information System (INIS)

Auluck, S. K. H.

2013-01-01

Recent resurgence of interest in applications of dense plasma focus and doubts about the conventional view of dense plasma focus as a purely irrotational compressive flow have re-opened questions concerning device optimization. In this context, this paper re-appraises and extends the analytical snowplow model of plasma focus sheath evolution developed by F. Gratton and J. M. Vargas [Energy Storage, Compression and Switching, edited by V. Nardi, H. Sahlin, and W. H. Bostick (Plenum, New York, 1983), Vol. 2, p. 353)] and shows its relevance to contemporary research. The Gratton-Vargas (GV) model enables construction of a special orthogonal coordinate system in which the plasma flow problem can be simplified and a model of sheath structure can be formulated. The Lawrenceville Plasma Physics (LPP) plasma focus facility, which reports neutron yield better than global scaling law, is shown to be operating closer to an optimum operating point of the GV model as compared with PF-1000

Methods and Apparatus for Pulsed-DC Dielectric Barrier Discharge Plasma Actuator and Circuit

Science.gov (United States)

Corke, Thomas C. (Inventor); Kaszeta, Richard (Inventor); Gold, Calman (Inventor)

2017-01-01

A plasma generating device intended to induce a flow in a fluid via plasma generation includes a dielectric separating two electrodes and a power supply. The first electrode is exposed to a fluid flow while the second electrode is positioned under the dielectric. The power supply is electrically coupled to a switch and the first and second electrodes. When the power supply is energized by repeated action of the switch, it causes a pulsed DC current between the electrodes which causes the fluid to ionize generating a plasma. The generation of the plasma induces a force with a velocity component in the fluid.

A Randomized Controlled Trial of Vildagliptin Versus Alogliptin: Effective Switch From Sitagliptin in Patients With Type 2 Diabetes.

Science.gov (United States)

Shigematsu, Erina; Yamakawa, Tadashi; Oba, Mari S; Suzuki, Jun; Nagakura, Jo; Kadonosono, Kazuaki; Terauchi, Yasuo

2017-07-01

We investigated the effects of vildagliptin or alogliptin on blood glucose and hemoglobin A1c (HbA1c) in patients with type 2 diabetes inadequately controlled by sitagliptin. In a single-center open-label trial, 35 patients with inadequate glycemic control on sitagliptin therapy (50 mg once daily) were randomly switched to treatment with vildagliptin (50 mg twice daily) or alogliptin (25 mg once daily). After 12 weeks, patients who failed to achieve the target HbA1c level of vildagliptin or alogliptin treatment were switched to high-dose sitagliptin (100 mg once daily) and the effect on glycemic control was assessed. Vildagliptin did not significantly alter the mean plasma glucose level (175.5 ± 54.4 mg/dL vs. 179.1 ± 73.4 mg/dL) or HbA1c (8.01% vs. 8.02%) after 12 weeks. With alogliptin, mean plasma glucose increased from 175.4 ± 50.9 mg/dL to 195.3 ± 55.0 mg/dL after 12 weeks and HbA1c increased significantly from 8.0% to 8.3% (P vildagliptin to high-dose sitagliptin (100 mg daily), HbA1c was increased to 8.3%, but it was significantly (P vildagliptin group than the alogliptin group (P = 0.008), but the response rate (achieving the target HbA1c vildagliptin, alogliptin, and sitagliptin) were different, and the effects of vildagliptin and sitagliptin were stronger than that of alogliptin.

A Two-Level Task Scheduler on Multiple DSP System for OpenCL

Directory of Open Access Journals (Sweden)

Li Tian

2014-04-01

Full Text Available This paper addresses the problem that multiple DSP system does not support OpenCL programming. With the compiler, runtime, and the kernel scheduler proposed, an OpenCL application becomes portable not only between multiple CPU and GPU, but also between embedded multiple DSP systems. Firstly, the LLVM compiler was imported for source-to-source translation in which the translated source was supported by CCS. Secondly, two-level schedulers were proposed to support efficient OpenCL kernel execution. The DSP/BIOS is used to schedule system level tasks such as interrupts and drivers; however, the synchronization mechanism resulted in heavy overhead during task switching. So we designed an efficient second level scheduler especially for OpenCL kernel work-item scheduling. The context switch process utilizes the 8 functional units and cross path links which was superior to DSP/BIOS in the aspect of task switching. Finally, dynamic loading and software managed CACHE were redesigned for OpenCL running on multiple DSP system. We evaluated the performance using some common OpenCL kernels from NVIDIA, AMD, NAS, and Parboil benchmarks. Experimental results show that the DSP OpenCL can efficiently exploit the computing resource of multiple cores.

Hall MHD Stability and Turbulence in Magnetically Accelerated Plasmas

Energy Technology Data Exchange (ETDEWEB)

H. R. Strauss

2012-11-27

The object of the research was to develop theory and carry out simulations of the Z pinch and plasma opening switch (POS), and compare with experimental results. In the case of the Z pinch, there was experimental evidence of ion kinetic energy greatly in excess of the ion thermal energy. It was thought that this was perhaps due to fine scale turbulence. The simulations showed that the ion energy was predominantly laminar, not turbulent. Preliminary studies of a new Z pinch experiment with an axial magnetic field were carried out. The axial magnetic is relevant to magneto - inertial fusion. These studies indicate the axial magnetic field makes the Z pinch more turbulent. Results were also obtained on Hall magnetohydrodynamic instability of the POS.

Control of open end plasma flow utilizing orbital stochasticity

International Nuclear Information System (INIS)

Hojo, Hitoshi

1995-01-01

It has been known that the control of plasma outside the confinement region of diverter plasma and others in a magnetic field confinement device is very important for improveing the confinement of bulk plasma. The control of plasma outside a confinement region bears two roles, one is the reduction of the thermal load on a diverter plate and others due to the plasma particles lost from the confinement region, and another is the restriction of the back flow of cold plasma and impurities generated outside the confinement region to a bulk plasma region. In this study, the new method of controlling plasma outside a confinement region called magnetic diverter is considered. To the plasma particles advancing along magnetic force lines, the reflection and capture of the plasma particles occur in the region of orbital stochasticity, and the thermal load on an end plate and the reverse flow to a bulk plasma region are restricted. The numerical computation model used regarding the particle control utilizing the orbital stochasticity and the results of calculating the orbit of plasma particles in a magnetic field are reported. (K.I.)

Arc detector system for extraction switches in LHC CERN

CERN Document Server

Dahlerup-Petersen, K; Kuper, E; Ovchar, V; Zverev, S

2006-01-01

The opening switches, which will be used in case of quenches or other failures in CERN’s future LHC collider to extract the large amounts of energy stored in the magnetic field of the superconducting chains of main dipoles (8 chains with 1350 MJ each) and main quadrupoles (16 chains with about 24 MJ each) consist of an array of series/parallel connected, electro-mechanical D.C. breakers, specifically designed for this particular application. During the opening process the magnet excitation current is transferred from the cluster of breakers to extraction resistors for rapid de-excitation of the magnet chain. An arc detector has been developed in order to facilitate the determination of the need for maintenance interventions on the switches. The paper describes the arc detector and highlight results from operation of the detector with a LHC pilot extraction...

Multicusp plasma containment apparatus

International Nuclear Information System (INIS)

Limpaecher, R.

1980-01-01

It has been discovered that plasma containment by a chamber having multi-pole magnetic cusp reflecting walls in combination with electronic injection for electrostatic containment provides the means for generating magnetic field free quiescent plasmas for practical application in ion-pumps, electronic switches, and the like. 1250 ''alnico v'' magnets 1/2 '' X 1/2 '' X 1 1/2 '' provide containment in one embodiment. Electromagnets embodying toroidal funneling extend the principle to fusion apparatus

Multi-Valued Spin Switch in a Semiconductor Microcavity

Science.gov (United States)

Paraïso, T. K.; Wouters, M.; Léger, Y.; Morier-Genoud, F.; Deveaudhyphen; Plédran, B.

2011-12-01

In this work, we report on the first realization of multi-valued spin switching in the solid-state. We investigate the physics of spinor bistability with microcavity polaritons in a trap. Spinor interactions lead to special bistability regimes with decoupled thresholds for spin-up and spin-down polaritons. This allows us to establish state-of-the-art spin switching operations. We evidence polarization hysteresis and determine appropriate conditions to achieve spin multistability. For a given excitation condition, three stable spin states coexist for the system. These results open new pathways for the development of innovative spin-based logic gates and memory devices.

Multi-probe ionization chamber system for nuclear-generated plasma diagnostics

International Nuclear Information System (INIS)

Choi, W.Y.; Ellis, W.H.

1990-01-01

This paper reports on the pulsed ionization chamber (PIC) plasma diagnostic system used in studies of nuclear seeded plasma kinetics upgraded to increase the capabilities and extend the range of plasma parameter measurements to higher densities and temperatures. The PIC plasma diagnostic chamber has been provided with additional measurement features in the form of conductivity and Langmuir probes, while the overall experimental system has been fully automated, with computerized control, measurement, data acquisition and analysis by means of IEEE-488 (GPIB) bus control and data transfer protocols using a Macintosh series microcomputer. The design and use of a simple TTL switching system enables remote switching among the various GPIB instruments comprising the multi-probe plasma diagnostic system using software, without the need for a microprocessor. The new system will be used to extend the present study of nuclear generated plasma in He, Ar, Xe, fissionable UF 6 and other fluorine containing gases

Polarity-Free Resistive Switching Characteristics of CuxO Films for Non-volatile Memory Applications

International Nuclear Information System (INIS)

Hang-Bing, Lv; Peng, Zhou; Xiu-Feng, Fu; Ming, Yin; Ya-Li, Song; Li, Tang; Ting-Ao, Tang; Yin-Yin, Lin

2008-01-01

Resistive switching characteristics of Cu x O films grown by plasma oxidation process at room temperature are investigated. Both bipolar and unipolar stable resistive switching behaviours are observed and confirmed by repeated current–voltage measurements. It is found that the RESET current is dependent on SET compliance current. The mechanism behind this new phenomenon can be understood in terms of conductive filaments formation/rupture with the contribution of Joule heating

Space-charge-mediated anomalous ferroelectric switching in P(VDF-TrEE) polymer films

KAUST Repository

Hu, Weijin

2014-11-12

We report on the switching dynamics of P(VDF-TrEE) copolymer devices and the realization of additional substable ferroelectric states via modulation of the coupling between polarizations and space charges. The space-charge-limited current is revealed to be the dominant leakage mechanism in such organic ferroelectric devices, and electrostatic interactions due to space charges lead to the emergence of anomalous ferroelectric loops. The reliable control of ferroelectric switching in P(VDF-TrEE) copolymers opens doors toward engineering advanced organic memories with tailored switching characteristics.

The use of laser beams for plasma diagnostics

International Nuclear Information System (INIS)

Gex, J.P.; Jolas, A.; Launspach, J.; Schirmann, D.

1975-01-01

The optical properties of lasers allow them to be a promising source for plasma diagnosis. The Q-switched lasers provide the opportunity to make observations in a very short time interval down to a few picoseconds. The laser space and time coherence properties allow interferometric measurements of plasma electron densities. Thus in the experiments of laser-matter interactions, the radiation obtained by frequency conversion of the Nd: glass laser emission is used for density measurements (up to 10 20 cm -3 ) in small scale plasmas (approximately equal to 1mm). Owing to the monochromaticity and high intensity of the Q-switched laser radiation, density fluctuations and microscopic instabilities of the plasma can be studied by Thompson scattering measurements. Finally, some statistically isotropic media become birefringent under the action of the strong electrical field of the laser beam radiation. This effect can be used for laser pulse duration measurements in a range not exceeding a few picoseconds [fr

Widening consumer access to medicines: a comparison of prescription to non-prescription medicine switch in Australia and New Zealand.

Directory of Open Access Journals (Sweden)

Natalie J Gauld

Full Text Available Despite similarities in health systems and Trans-Tasman Harmonization of medicines scheduling, New Zealand is more active than Australia in 'switching' (reclassifying medicines from prescription to non-prescription.To identify and compare enablers and barriers to switch in New Zealand and Australia.We conducted and analyzed 27 in-depth personal interviews with key participants in NZ and Australia and international participants previously located in Australia, and analyzed records of meetings considering switches (2000-2013. Analysis of both sets of data entailed a heuristic qualitative approach that embraced the lead researcher's knowledge and experience.The key themes identified were conservatism and political influences in Australia, and an open attitude, proactivity and flexibility in NZ. Pharmacist-only medicine schedules and individuals holding a progressive attitude were proposed to facilitate switch in both countries. A pharmacy retail group drove many switches in NZ ('third-party switch', unlike Australia. Barriers to switch in both countries included small market sizes, funding of prescription medicines and cost of doctor visits, and lack of market exclusivity. In Australia, advertising limitations for pharmacist-only medicines reportedly discouraged industry from submitting switch applications. Perceptions of pharmacy performance could help or hinder switches.Committee and regulator openness to switch, and confidence in pharmacy appear to influence consumer access to medicines. The pharmacist-only medicine schedule in Australasia and the rise of third-party switch and flexibility in switch in NZ could be considered elsewhere to enable switch.

Widening consumer access to medicines: a comparison of prescription to non-prescription medicine switch in Australia and New Zealand.

Science.gov (United States)

Gauld, Natalie J; Kelly, Fiona S; Emmerton, Lynne M; Buetow, Stephen A

2015-01-01

Despite similarities in health systems and Trans-Tasman Harmonization of medicines scheduling, New Zealand is more active than Australia in 'switching' (reclassifying) medicines from prescription to non-prescription. To identify and compare enablers and barriers to switch in New Zealand and Australia. We conducted and analyzed 27 in-depth personal interviews with key participants in NZ and Australia and international participants previously located in Australia, and analyzed records of meetings considering switches (2000-2013). Analysis of both sets of data entailed a heuristic qualitative approach that embraced the lead researcher's knowledge and experience. The key themes identified were conservatism and political influences in Australia, and an open attitude, proactivity and flexibility in NZ. Pharmacist-only medicine schedules and individuals holding a progressive attitude were proposed to facilitate switch in both countries. A pharmacy retail group drove many switches in NZ ('third-party switch'), unlike Australia. Barriers to switch in both countries included small market sizes, funding of prescription medicines and cost of doctor visits, and lack of market exclusivity. In Australia, advertising limitations for pharmacist-only medicines reportedly discouraged industry from submitting switch applications. Perceptions of pharmacy performance could help or hinder switches. Committee and regulator openness to switch, and confidence in pharmacy appear to influence consumer access to medicines. The pharmacist-only medicine schedule in Australasia and the rise of third-party switch and flexibility in switch in NZ could be considered elsewhere to enable switch.

Electrochemical structure-switching sensing using nanoplasmonic devices

Energy Technology Data Exchange (ETDEWEB)

Patskovsky, Sergiy; Dallaire, Anne-Marie; Blanchard-Dionne, Andre-Pierre; Meunier, Michel [Department of Engineering Physics, Laser Processing and Plasmonics Laboratory, Polytechnique, Montreal, Station Centre-ville, QC (Canada); Vallee-Belisle, Alexis [Laboratory of Biosensors and Nanomachines, Departement de Chimie, Universite de Montreal, QC (Canada)

2015-12-15

In this article, the implementation of electrochemical plasmonic nanostructures functionalized with DNA-based structure-switching sensors is presented. eNanoSPR devices with open and microfluidic measurement cells are developed on the base of nanohole arrays in 100 nm gold film and applied for combined microscopic and electrochemical surface plasmon (eSPR) visualization. eSPR voltammograms and spectroscopy are performed using planar three electrode schematic with plasmonic nanostructure operated as working electrode. Limit of detection of eNanoSPR devices for oligonucleotide hybridization is estimated in the low nanomolar and applications for structure-switching electro-plasmonic sensing in complex liquids are discussed. (copyright 2015 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

IEEE conference record -- Abstracts

International Nuclear Information System (INIS)

Anon.

1994-01-01

This conference covers the following areas: computational plasma physics; vacuum electronic; basic phenomena in fully ionized plasmas; plasma, electron, and ion sources; environmental/energy issues in plasma science; space plasmas; plasma processing; ball lightning/spherical plasma configurations; plasma processing; fast wave devices; magnetic fusion; basic phenomena in partially ionized plasma; dense plasma focus; plasma diagnostics; basic phenomena in weakly ionized gases; fast opening switches; MHD; fast z-pinches and x-ray lasers; intense ion and electron beams; laser-produced plasmas; microwave plasma interactions; EM and ETH launchers; solid state plasmas and switches; intense beam microwaves; and plasmas for lighting. Separate abstracts were prepared for 416 papers in this conference

Capacitor Bank 'CHANDI' for Plasma Target Production for Liner Plasma Interaction

International Nuclear Information System (INIS)

Shukla, R.; Sharma, S.K.; Debnath, K.; Shyam, A.

2006-01-01

A capacitor bank is fabricated to drive (JXB) Plasma gun to generate hot plasma (target) for liner plasma investigation. The bank will also be used for driving other pintch experiments. The bank consists of 8 capacitors connected in parallel, each having capacitance of 178 μF giving a total of 1424uF. The bank is charged at 15 kV using a 28 kV power supply charging the capacitors in 65 seconds utilizing full wave charging technique. The total energy of the bank is 160kJ at 15kV. A modeling of power supply was done so that all the components involved are utilized to their operating limit safely. Moreover to give fault protection to the capacitor bank we have implemented the neutral control technique in the power supply. The capacitor bank is discharged to the inductive load through an ignitron switch of very high coulomb rating and capable of withstanding high voltages at its electrodes. The cables used for connecting capacitor bank with ignitron switch are used in parallel to give them collective capability of bearing capacitor discharge currents. These cables are capable of holding high DC voltages (40kV), which appear at the time of charging of the bank. The bank is tested and is operational

Supplementary insurance as a switching cost for basic health insurance: Empirical results from the Netherlands.

Science.gov (United States)

Willemse-Duijmelinck, Daniëlle M I D; van de Ven, Wynand P M M; Mosca, Ilaria

2017-10-01

Nearly everyone with a supplementary insurance (SI) in the Netherlands takes out the voluntary SI and the mandatory basic insurance (BI) from the same health insurer. Previous studies show that many high-risks perceive SI as a switching cost for BI. Because consumers' current insurer provides them with a guaranteed renewability, SI is a switching cost if insurers apply selective underwriting to new applicants. Several changes in the Dutch health insurance market increased insurers' incentives to counteract adverse selection for SI. Tools to do so are not only selective underwriting, but also risk rating and product differentiation. If all insurers use the latter tools without selective underwriting, SI is not a switching cost for BI. We investigated to what extent insurers used these tools in the periods 2006-2009 and 2014-2015. Only a few insurers applied selective underwriting: in 2015, 86% of insurers used open enrolment for all their SI products, and the other 14% did use open enrolment for their most common SI products. As measured by our indicators, the proportion of insurers applying risk rating or product differentiation did not increase in the periods considered. Due to the fear of reputation loss insurers may have used 'less visible' tools to counteract adverse selection that are indirect forms of risk rating and product differentiation and do not result in switching costs. So, although many high-risks perceive SI as a switching cost, most insurers apply open enrolment for SI. By providing information to high-risks about their switching opportunities, the government could increase consumer choice and thereby insurers' incentives to invest in high-quality care for high-risks. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of Cisco Open Network Environment (ONE) OpenFlow Controller Implementation

Science.gov (United States)

2014-08-01

Software - Defined Networking ( SDN ), when fully realized, offer many improvements over the current rigid and...functionalities like handshake, connection setup, switch management, and security. 15. SUBJECT TERMS OpenFlow, software - defined networking , Cisco ONE, SDN ...innovating packet-forwarding technologies. Network device roles are strictly defined with little or no flexibility. In Software - Defined Networks ( SDNs ),

Study of Pulsed vs. RF Plasma Properties for Surface Processing Applications

Science.gov (United States)

Tang, Ricky; Hopkins, Matthew; Barnat, Edward; Miller, Paul

2015-09-01

The ability to manipulate the plasma parameters (density, E/N) was previously demonstrated using a double-pulsed column discharge. Experiments extending this to large-surface plasmas of interest to the plasma processing community were conducted. Differences between an audio-frequency pulsed plasma and a radio-frequency (rf) discharge, both prevalent in plasma processing applications, were studied. Optical emission spectroscopy shows higher-intensity emission in the UV/visible range for the pulsed plasma comparing to the rf plasma at comparable powers. Data suggest that the electron energy is higher for the pulsed plasma leading to higher ionization, resulting in increased ion density and ion flux. Diode laser absorption measurements of the concentration of the 1S5 metastable and 1S4 resonance states of argon (correlated with the plasma E/N) provide comparisons between the excitation/ionization states of the two plasmas. Preliminary modeling efforts suggest that the low-frequency polarity switch causes a much more abrupt potential variation to support interesting transport phenomena, generating a ``wave'' of higher temperature electrons leading to more ionization, as well as ``sheath capture'' of a higher density bolus of ions that are then accelerated during polarity switch.

Effect of finited pressure on plasma stability and particle motion i axial-assymetrical open traps

International Nuclear Information System (INIS)

Kotel'nikov, I.A.

1984-01-01

Hydrodynamic equilibrium confiqurations of plasma are investigated as well as the processes of cross-section transfer in axial-asymmetrical open traps. It is shown that drift surfaces are essentially deformed allowing for the final β, and, as a rule, the property of local injection is disturbed. But non-injection of particle drift surfaces with different energies and a magnetic moment in a paraxial trap turns out to be small by the perimeter of paraxiallity even at βapproximately1

AC/DC/pulsed-power modulator for corona-plasma generation

NARCIS (Netherlands)

Ariaans, T.H.P.; Pemen, A.J.M.; Winands, G.J.J.; Heesch, van E.J.M.; Liu, Z.

2009-01-01

Gas-cleaning techniques using nonthermal plasma are slowly introduced into industry nowadays. In this paper, we present a novel power modulator for the efficient generation of large-volume corona plasma. No expensive high-voltage components are required. Switching is done at an intermediate voltage

Transient effects in beam-plasma interactions in a space simulation chamber stimulated by a fast pulse electron gun

Science.gov (United States)

Raitt, W. J.; Banks, P. M.; Denig, W. F.; Anderson, H. R.

1982-01-01

Interest in the interaction of electron beams with plasma generated by ionization caused by the primary electron beam was stimulated by the need to develop special vacuum tubes to operate in the kMHz frequency region. The experiments of Getty and Smullin (1963) indicated that the interaction of an energetic electron beam with its self-produced plasma resulted in the emission of wave energy over a wide range of frequencies associated with cyclotron and longitudinal plasma instabilities. This enhanced the thermal plasma density in the vicinity of the beam, and the term Beam-Plasma Discharge (BPD) was employed to described this phenomenon. The present investigation is concerned with some of the transient phenomena associated with wave emission during the beam switch-on and switch-off periods. Results are presented on the changes in electron energy spectra on a time scale of tens of milliseconds following beam switch-on. The results are discussed in terms of the beam plasma discharge phenomenon.

Transient effects in beam-plasma interactions in a space simulation chamber stimulated by a fast pulse electron gun

International Nuclear Information System (INIS)

Raitt, W.J.; Banks, P.M.

1982-01-01

Interest in the interaction of electron beams with plasma generated by ionization caused by the primary electron beam was stimulated by the need to develop special vacuum tubes to operate in the kMHz frequency region. The experiments of Getty and Smullin (1963) indicated that the interaction of an energetic electron beam with its self-produced plasma resulted in the emission of wave energy over a wide range of frequencies associated with cyclotron and longitudinal plasma instabilities. This enhanced the thermal plasma density in the vicinity of the beam, and the term Beam-Plasma Discharge (BPD) was employed to described this phenomenon. The present investigation is concerned with some of the transient phenomena associated with wave emission during the beam switch-on and switch-off periods. Results are presented on the changes in electron energy spectra on a time scale of tens of milliseconds following beam switch-on. The results are discussed in terms of the beam plasma discharge phenomenon. 5 references

Thermal Simulations, Open Boundary Conditions and Switches

Science.gov (United States)

Burnier, Yannis; Florio, Adrien; Kaczmarek, Olaf; Mazur, Lukas

2018-03-01

SU(N) gauge theories on compact spaces have a non-trivial vacuum structure characterized by a countable set of topological sectors and their topological charge. In lattice simulations, every topological sector needs to be explored a number of times which reflects its weight in the path integral. Current lattice simulations are impeded by the so-called freezing of the topological charge problem. As the continuum is approached, energy barriers between topological sectors become well defined and the simulations get trapped in a given sector. A possible way out was introduced by Lüscher and Schaefer using open boundary condition in the time extent. However, this solution cannot be used for thermal simulations, where the time direction is required to be periodic. In this proceedings, we present results obtained using open boundary conditions in space, at non-zero temperature. With these conditions, the topological charge is not quantized and the topological barriers are lifted. A downside of this method are the strong finite-size effects introduced by the boundary conditions. We also present some exploratory results which show how these conditions could be used on an algorithmic level to reshuffle the system and generate periodic configurations with non-zero topological charge.

Thermal Simulations, Open Boundary Conditions and Switches

Directory of Open Access Journals (Sweden)

Burnier Yannis

2018-01-01

Full Text Available SU(N gauge theories on compact spaces have a non-trivial vacuum structure characterized by a countable set of topological sectors and their topological charge. In lattice simulations, every topological sector needs to be explored a number of times which reflects its weight in the path integral. Current lattice simulations are impeded by the so-called freezing of the topological charge problem. As the continuum is approached, energy barriers between topological sectors become well defined and the simulations get trapped in a given sector. A possible way out was introduced by Lüscher and Schaefer using open boundary condition in the time extent. However, this solution cannot be used for thermal simulations, where the time direction is required to be periodic. In this proceedings, we present results obtained using open boundary conditions in space, at non-zero temperature. With these conditions, the topological charge is not quantized and the topological barriers are lifted. A downside of this method are the strong finite-size effects introduced by the boundary conditions. We also present some exploratory results which show how these conditions could be used on an algorithmic level to reshuffle the system and generate periodic configurations with non-zero topological charge.

Evolution of the transport coefficients for the transient processes after ECRH switch-on/off in the T-10 tokamak

International Nuclear Information System (INIS)

Andreev, V.F.; Danilov, A.V.; Dnestrovskij, Yu.N.; Ossipenko, M.V.; Razumova, K.A.; Sushkov, A.V.

2005-01-01

A study of the transient processes after ECRH switch-on/off in the T-10 tokamak shows that an electron ITB appears near the q∼3/2 resonance surface in regimes with suppressed sawtooth oscillations. When the gradient of the electron temperature in the plasma centre after additional on-axis ECRH exceeds some critical value, the electron ITB is weakened and the heat flux spreads from the heating region to the plasma periphery practically instantly. This looks like a jump of the heat flux through the entire plasma region. Therefore, to describe the electron heat transport in a tokamak plasma after the ECRH switch-on/off, three different physical processes should be taken into account: a) the transient process of plasma heating inside the region bounded by the temporal electron ITB; b) the weakening of the electron ITB accompanied by the heat efflux to the plasma periphery during hundreds of microseconds; c) the consequent diffusive evolution of the electron temperature profile with the conservation of the relative electron temperature gradient ∇T/T. (author)

Switching to sanitation: Understanding latrine adoption in a representative panel of rural Indian households.

Science.gov (United States)

Coffey, Diane; Spears, Dean; Vyas, Sangita

2017-09-01

Open defecation, which is still practiced by about a billion people worldwide, is one of the most compelling examples of how place influences health in developing countries. Efforts by governments and development organizations to address the world's remaining open defecation would be greatly supported by a better understanding of why some people adopt latrines and others do not. We analyze the 2005 and 2012 rounds of the India Human Development Survey (IHDS), a nationally representative panel of households in India, the country which is home to 60% of the people worldwide who defecate in the open. Among rural households that defecated in the open in 2005, we investigate what baseline properties and what changes over time are associated with switching to latrine use between 2005 and 2012. We find that households that are richer or better educated, that have certain demographic properties, or that improved their homes over this period were more likely to switch to using a latrine or toilet. However, each of these effect sizes is small; overall switching to latrine use from open defecation is low; and no ready household-level mechanisms are available for sanitation programs to widely influence these factors. Our research adds to a growing consensus in the literature that the social context should not be overlooked when trying to understand and bring about change in sanitation behavior. Copyright © 2017 Elsevier Ltd. All rights reserved.

A novel solid-state control system for the minimization of re-switching transient currents of induction motor

International Nuclear Information System (INIS)

Abro, M.R.; Larik, A.S.; Mahar, M.A.

2005-01-01

This work is an investigation into the minimizing re-closure transient currents of induction motors by activating NOVEL solid state control system switching at a matched condition. This emphasis is placed upon-circuit transition starting of cage motors, particularly star-delta switching. The initial study is carried out on single-phase induction motion. This system is capable of effective sensing re-closure of a switched off running single-phase induction motor. Further this scheme could be developed to give sequential delta closure of a switched off running three-phase induction motor during 1st cycles following the opening of the star mode. Consideration is also given to the possibility of using sensed re-closure to minimize transient whenever the supply to a running induction motor is briefly interrupted, irrespective of whether the interruption is by accident design. A brief study is made into the type of transient currents generated by opening the circuit of a running induction motor. The importance of the switching pattern for star-delta starting is explained and emphasized. (author)

Technology of a small plasma focus

International Nuclear Information System (INIS)

Lee, S.

1990-01-01

This paper reviews plasma focus technology, including the underlying dynamic and energy balance theory, scaling of the neutron yield, cost effectiveness of the design, as well as the main subsystems, e.g., capacitor bank, spark-gap switch and triggering electronics, the plasma focus tube, some simple diagnostics, and a high-voltage charger. It discusses the range of densities and temperatures available with a small plasma focus, and the type of experiments and applications that can be carried out with it. 61 refs, 21 figs

Proto-I switching and diode studies

International Nuclear Information System (INIS)

Prestwich, K.R.; Miller, P.A.; McDaniel, D.H.; Poukey, J.W.; Widner, M.M.; Goldstein, S.A.

1975-01-01

Proto-I is a 3 MV, 800 kA, 24 ns electron beam accelerator that is under development at Sandia Laboratories. It represents an initial effort to develop a scalable technology that is applicable to accelerators for electron beam driven, inertial confinement fusion studies. Energy is supplied to each of the two diodes from six oil-dielectric Blumlein transmission lines (PFL) operating in parallel. A Marx generator charges three intermediate storage, water-dielectric capacitors which subsequently transfer the stored energy to the PFL. The discharge of the PFL is initiated by the simultaneous closure of 12 triggered oil-dielectric rail switches. Data will be presented on the operation of these multichannel switches. The two diodes have a common anode. Cathode diameters can be varied from 10 to 60 cm. Results of initial diode experiments and comparisons with theory are discussed. Plasma filled diode experiments are also reported, indicating pinch collapse velocities in excess of 10 9 cm/s

Overexpression of plasma membrane H+-ATPase in guard cells promotes light-induced stomatal opening and enhances plant growth.

Science.gov (United States)

Wang, Yin; Noguchi, Ko; Ono, Natsuko; Inoue, Shin-ichiro; Terashima, Ichiro; Kinoshita, Toshinori

2014-01-07

Stomatal pores surrounded by a pair of guard cells in the plant epidermis control gas exchange between plants and the atmosphere in response to light, CO2, and the plant hormone abscisic acid. Light-induced stomatal opening is mediated by at least three key components: the blue light receptor phototropin (phot1 and phot2), plasma membrane H(+)-ATPase, and plasma membrane inward-rectifying K(+) channels. Very few attempts have been made to enhance stomatal opening with the goal of increasing photosynthesis and plant growth, even though stomatal resistance is thought to be the major limiting factor for CO2 uptake by plants. Here, we show that transgenic Arabidopsis plants overexpressing H(+)-ATPase using the strong guard cell promoter GC1 showed enhanced light-induced stomatal opening, photosynthesis, and plant growth. The transgenic plants produced larger and increased numbers of rosette leaves, with ∼42-63% greater fresh and dry weights than the wild type in the first 25 d of growth. The dry weights of total flowering stems of 45-d-old transgenic plants, including seeds, siliques, and flowers, were ∼36-41% greater than those of the wild type. In addition, stomata in the transgenic plants closed normally in response to darkness and abscisic acid. In contrast, the overexpression of phototropin or inward-rectifying K(+) channels in guard cells had no effect on these phenotypes. These results demonstrate that stomatal aperture is a limiting factor in photosynthesis and plant growth, and that manipulation of stomatal opening by overexpressing H(+)-ATPase in guard cells is useful for the promotion of plant growth.

Injection of a coaxial-gun-produced magnetized plasma into a background helicon plasma

Science.gov (United States)

Zhang, Yue; Lynn, Alan; Gilmore, Mark; Hsu, Scott

2014-10-01

A compact coaxial plasma gun is employed for experimental investigation of plasma bubble relaxation into a lower density background plasma. Experiments are being conducted in the linear device HelCat at UNM. The gun is powered by a 120-uF ignitron-switched capacitor bank, which is operated in a range of 5 to 10 kV and 100 kA. Multiple diagnostics are employed to investigate the plasma relaxation process. Magnetized argon plasma bubbles with velocities 1.2Cs, densities 1020 m-3 and electron temperature 13eV have been achieved. The background helicon plasma has density 1013 m-3, magnetic field from 200 to 500 Gauss and electron temperature 1eV. Several distinct operational regimes with qualitatively different dynamics are identified by fast CCD camera images. Additionally a B-dot probe array has been employed to measure the spatial toroidal and poloidal magnetic flux evolution to identify plasma bubble configurations. Experimental data and analysis will be presented.

Transient voltage sharing in series-coupled high voltage switches

Directory of Open Access Journals (Sweden)

Editorial Office

1992-07-01

Full Text Available For switching voltages in excess of the maximum blocking voltage of a switching element (for example, thyristor, MOSFET or bipolar transistor such elements are often coupled in series - and additional circuitry has to be provided to ensure equal voltage sharing. Between each such series element and system ground there is a certain parasitic capacitance that may draw a significant current during high-speed voltage transients. The "open" switch is modelled as a ladder network. Analy­sis reveals an exponential progression in the distribution of the applied voltage across the elements. Overstressing thus oc­curs in some of the elements at levels of the total voltage that are significantly below the design value. This difficulty is overcome by grading the voltage sharing circuitry, coupled in parallel with each element, in a prescribed manner, as set out here.

Application of an impedance matching transformer to a plasma focus.

Science.gov (United States)

Bures, B L; James, C; Krishnan, M; Adler, R

2011-10-01

A plasma focus was constructed using an impedance matching transformer to improve power transfer between the pulse power and the dynamic plasma load. The system relied on two switches and twelve transformer cores to produce a 100 kA pulse in short circuit on the secondary at 27 kV on the primary with 110 J stored. With the two transformer systems in parallel, the Thevenin equivalent circuit parameters on the secondary side of the driver are: C = 10.9 μF, V(0) = 4.5 kV, L = 17 nH, and R = 5 mΩ. An equivalent direct drive circuit would require a large number of switches in parallel, to achieve the same Thevenin equivalent. The benefits of this approach are replacement of consumable switches with non-consumable transformer cores, reduction of the driver inductance and resistance as viewed by the dynamic load, and reduction of the stored energy to produce a given peak current. The system is designed to operate at 100 Hz, so minimizing the stored energy results in less load on the thermal management system. When operated at 1 Hz, the neutron yield from the transformer matched plasma focus was similar to the neutron yield from a conventional (directly driven) plasma focus at the same peak current.

Evaporation of Droplets in Plasma Spray-Physical Vapor Deposition Based on Energy Compensation Between Self-Cooling and Plasma Heat Transfer

Science.gov (United States)

Liu, Mei-Jun; Zhang, Meng; Zhang, Qiang; Yang, Guan-Jun; Li, Cheng-Xin; Li, Chang-Jiu

2017-10-01

In the plasma spray-physical vapor deposition process (PS-PVD), there is no obvious heating to the feedstock powders due to the free molecular flow condition of the open plasma jet. However, this is in contrast to recent experiments in which the molten droplets are transformed into vapor atoms in the open plasma jet. In this work, to better understand the heating process of feedstock powders in the open plasma jet of PS-PVD, an evaporation model of molten ZrO2 is established by examining the heat and mass transfer process of molten ZrO2. The results reveal that the heat flux in PS-PVD open plasma jet (about 106 W/m2) is smaller than that in the plasma torch nozzle (about 108 W/m2). However, the flying distance of molten ZrO2 in the open plasma jet is much longer than that in the plasma torch nozzle, so the heating in the open plasma jet cannot be ignored. The results of the evaporation model show that the molten ZrO2 can be partly evaporated by self-cooling, whereas the molten ZrO2 with a diameter <0.28 μm and an initial temperature of 3247 K can be completely evaporated within the axial distance of 450 mm by heat transfer.

Plasma response to electron energy filter in large volume plasma device

International Nuclear Information System (INIS)

Sanyasi, A. K.; Awasthi, L. M.; Mattoo, S. K.; Srivastava, P. K.; Singh, S. K.; Singh, R.; Kaw, P. K.

2013-01-01

An electron energy filter (EEF) is embedded in the Large Volume Plasma Device plasma for carrying out studies on excitation of plasma turbulence by a gradient in electron temperature (ETG) described in the paper of Mattoo et al. [S. K. Mattoo et al., Phys. Rev. Lett. 108, 255007 (2012)]. In this paper, we report results on the response of the plasma to the EEF. It is shown that inhomogeneity in the magnetic field of the EEF switches on several physical phenomena resulting in plasma regions with different characteristics, including a plasma region free from energetic electrons, suitable for the study of ETG turbulence. Specifically, we report that localized structures of plasma density, potential, electron temperature, and plasma turbulence are excited in the EEF plasma. It is shown that structures of electron temperature and potential are created due to energy dependence of the electron transport in the filter region. On the other hand, although structure of plasma density has origin in the particle transport but two distinct steps of the density structure emerge from dominance of collisionality in the source-EEF region and of the Bohm diffusion in the EEF-target region. It is argued and experimental evidence is provided for existence of drift like flute Rayleigh-Taylor in the EEF plasma

Active high-power RF pulse compression using optically switched resonant delay lines

International Nuclear Information System (INIS)

Tantawi, S.G.; Ruth, R.D.; Vlieks, A.E.

1996-11-01

The authors present the design and a proof of principle experimental results of an optically controlled high power rf pulse compression system. The design should, in principle, handle few hundreds of Megawatts of power at X-band. The system is based on the switched resonant delay line theory. It employs resonant delay lines as a means of storing rf energy. The coupling to the lines is optimized for maximum energy storage during the charging phase. To discharge the lines, a high power microwave switch increases the coupling to the lines just before the start of the output pulse. The high power microwave switch, required for this system, is realized using optical excitation of an electron-hole plasma layer on the surface of a pure silicon wafer. The switch is designed to operate in the TE 01 mode in a circular waveguide to avoid the edge effects present at the interface between the silicon wafer and the supporting waveguide; thus, enhancing its power handling capability

Analysis of cytokine profile and growth factors in platelet-rich plasma obtained by open systems and commercial columns.

Science.gov (United States)

Pochini, Alberto de Castro; Antonioli, Eliane; Bucci, Daniella Zanetti; Sardinha, Luiz Roberto; Andreoli, Carlos Vicente; Ferretti, Mario; Ejnisman, Benno; Goldberg, Anna Carla; Cohen, Moisés

2016-01-01

To evaluate growth factors and cytokines in samples of platelet-rich plasma obtained by three different centrifugation methods. Peripheral blood of six individuals with no hematological diseases, aged 18 to 68 years, was drawn to obtain platelet-rich plasma, using the open method and commercial columns by Medtronic and Biomet. The products obtained with the different types of centrifugation were submitted to laboratory analysis, including pro-inflammatory cytokines and chemokines by flow cytometry assays, the concentration of fibroblast growth factors-2 (FGF-2) and transforming growth factor-beta1 (TGF-β1). The diverse separation methods generated systematically different profiles regarding number of platelets and leukocytes. The Medtronic system yielded a product with the highest concentration of platelets, and the open method, with the lowest concentration of platelets. The results of cytokine analysis showed that the different types of centrifugation yielded products with high concentrations of interleukin 8, interleukin 1β. The open system resulted in a product with high levels of interleukin 6. Other cytokines and chemokines measured were similar between systems. The product obtained with the open method showed higher levels of TGF-β1 in relation to other systems and low FGF-2 levels. The formed elements, growth factors and cytokines in samples of platelet-rich plasma varied according to the centrifugation technique used. Avaliar fatores de crescimento e citocinas em amostras de plasma rico em plaquetas obtidas por três diferentes métodos de centrifugação. Foi coletado sangue periférico de seis indivíduos, sem doença hematológica, com idades entre 18 e 68 anos, para obtenção de plasma rico em plaquetas, utilizando o método aberto e sistemas comerciais das empresas Medtronic e Biomet. Os produtos obtidos com os diferentes tipos de centrifugação foram submetidos às análises laboratoriais, incluindo citocinas próinflamatórias e quimiocinas

Patterned deposition by atmospheric pressure plasma-enhanced spatial atomic layer deposition

NARCIS (Netherlands)

Poodt, P.; Kniknie, B.J.; Branca, A.; Winands, G.J.J.; Roozeboom, F.

2011-01-01

An atmospheric pressure plasma enhanced atomic layer deposition reactor has been developed, to deposit Al2O3 films from trimethyl aluminum and an He/O2 plasma. This technique can be used for 2D patterned deposition in a single in-line process by making use of switched localized plasma sources. It

Global (volume-averaged) model of inductively coupled chlorine plasma : influence of Cl wall recombination and external heating on continuous and pulse-modulated plasmas

NARCIS (Netherlands)

Kemaneci, E.H.; Carbone, E.A.D.; Booth, J.P.; Graef, W.A.A.D.; Dijk, van J.; Kroesen, G.M.W.

An inductively coupled radio-frequency plasma in chlorine is investigated via a global (volume-averaged) model, both in continuous and square wave modulated power input modes. After the power is switched off (in a pulsed mode) an ion–ion plasma appears. In order to model this phenomenon, a novel

Development of High Power Vacuum Tubes for Accelerators and Plasma Heating

International Nuclear Information System (INIS)

Srivastava, Vishnu

2012-01-01

High pulsed power magnetrons and klystrons for medical and industrial accelerators, and high CW power klystrons and gyrotrons for plasma heating in tokamak, are being developed at CEERI. S-band 2.0MW pulsed tunable magnetrons of centre frequency 2856MHz and 2998 MHz were developed, and S-band 2.6MW pulsed tunable magnetron is being developed for medical LINAC, and 3MW pulsed tunable magnetron is being developed for industrial accelerator. S-band (2856MHz), 5MW pulsed klystron was developed for particle accelerator, and S-band 6MW pulsed klystron is under development for 10MeV industrial accelerator. 350MHz, 100kW (CW) klystron is being developed for proton accelerator, and C-band 250kW (CW) klystron is being developed for plasma heating. 42GHz, 200kW (CW/Long pulse) gyrotron is under development for plasma heating. Plasma filled tubes are also being developed for switching. 25kV/1kA and 40kV/3kA thyratrons were developed for high voltage high current switching in pulse modulators for magnetrons and klystrons. 25kV/3kA Pseudospark switch of current rise time of 1kA/|a-sec and pulse repetition rate of 500Hz is being developed. Plasma assisted high power microwave device is also being investigated.

Development of High Power Vacuum Tubes for Accelerators and Plasma Heating

Science.gov (United States)

Srivastava, Vishnu

2012-11-01

High pulsed power magnetrons and klystrons for medical and industrial accelerators, and high CW power klystrons and gyrotrons for plasma heating in tokamak, are being developed at CEERI. S-band 2.0MW pulsed tunable magnetrons of centre frequency 2856MHz and 2998 MHz were developed, and S-band 2.6MW pulsed tunable magnetron is being developed for medical LINAC, and 3MW pulsed tunable magnetron is being developed for industrial accelerator. S-band (2856MHz), 5MW pulsed klystron was developed for particle accelerator, and S-band 6MW pulsed klystron is under development for 10MeV industrial accelerator. 350MHz, 100kW (CW) klystron is being developed for proton accelerator, and C-band 250kW (CW) klystron is being developed for plasma heating. 42GHz, 200kW (CW/Long pulse) gyrotron is under development for plasma heating. Plasma filled tubes are also being developed for switching. 25kV/1kA and 40kV/3kA thyratrons were developed for high voltage high current switching in pulse modulators for magnetrons and klystrons. 25kV/3kA Pseudospark switch of current rise time of 1kA/|a-sec and pulse repetition rate of 500Hz is being developed. Plasma assisted high power microwave device is also being investigated.

Particle-in-cell simulations of fast magnetic field penetration into plasmas due to the Hall electric field

International Nuclear Information System (INIS)

Swanekamp, S.B.; Grossmann, J.M.; Fruchtman, A.; Oliver, B.V.; Ottinger, P.F.

1996-01-01

Particle-in-cell (PIC) simulations are used to study the penetration of magnetic field into plasmas in the electron-magnetohydrodynamic (EMHD) regime. These simulations represent the first definitive verification of EMHD with a PIC code. When ions are immobile, the PIC results reproduce many aspects of fluid treatments of the problem. However, the PIC results show a speed of penetration that is between 10% and 50% slower than predicted by one-dimensional fluid treatments. In addition, the PIC simulations show the formation of vortices in the electron flow behind the EMHD shock front. The size of these vortices is on the order of the collisionless electron skin depth and is closely coupled to the effects of electron inertia. An energy analysis shows that one-half the energy entering the plasma is stored as magnetic field energy while the other half is shared between internal plasma energy (thermal motion and electron vortices) and electron kinetic energy loss from the volume to the boundaries. The amount of internal plasma energy saturates after an initial transient phase so that late in time the rate that magnetic energy increases in the plasma is the same as the rate at which kinetic energy flows out through the boundaries. When ions are mobile it is observed that axial magnetic field penetration is followed by localized thinning in the ion density. The density thinning is produced by the large electrostatic fields that exist inside the electron vortices which act to reduce the space-charge imbalance necessary to support the vortices. This mechanism may play a role during the opening process of a plasma opening switch. copyright 1996 American Institute of Physics

Influence of oxygen doping on resistive-switching characteristic of a-Si/c-Si device

Science.gov (United States)

Zhang, Jiahua; Chen, Da; Huang, Shihua

2017-12-01

The influence of oxygen doping on resistive-switching characteristics of Ag/a-Si/p+-c-Si device was investigated. By oxygen doping in the growth process of amorphous silicon, the device resistive-switching performances, such as the ON/OFF resistance ratios, yield and stability were improved, which may be ascribed to the significant reduction of defect density because of oxygen incorporation. The device I-V characteristics are strongly dependent on the oxygen doping concentration. As the oxygen doping concentration increases, the Si-rich device gradually transforms to an oxygen-rich device, and the device yield, switching characteristics, and stability may be improved for silver/oxygen-doped a-Si/p+-c-Si device. Finally, the device resistive-switching mechanism was analyzed. Project supported by the Zhejiang Provincial Natural Science Foundation of China (No. LY17F040001), the Open Project Program of Surface Physics Laboratory (National Key Laboratory) of Fudan University (No. KF2015_02), the Open Project Program of National Laboratory for Infrared Physics, Chinese Academy of Sciences (No. M201503), the Zhejiang Provincial Science and Technology Key Innovation Team (No. 2011R50012), and the Zhejiang Provincial Key Laboratory (No. 2013E10022).

Effect of the switching time on the performance of an adsorption chiller

International Nuclear Information System (INIS)

Hong, Sang Woo; Chung, Jae Dong; Kwon, Oh Kyung

2016-01-01

The switching time is an important operating condition that must be correctly anticipated for an effective adsorption cooling system. Before the adsorption (or desorption) process begins, time is required to cool down (or heat up) the bed temperature so that the bed pressure reaches the evaporator pressure (or condenser pressure). During the switching time, the supplied heat is reduced and pressure overload conditions can be avoided. The switching time cannot be estimated early on, and an improper switching time degrades the system performance. Thus, this study provides guideline with which to determine the required time to open this valve, i.e., the switching time, and carefully examines the thermo-physical behavior in the adsorption bed during this period. A two-dimensional numerical method with the composite sorbent of SWS-1L and a water pair is applied to a fin-tube type adsorption chiller. Three cases of no switching time, the optimal switching time and a double the optimal switching time are examined. The results show that no consideration of the switching time overestimates the performance of the adsorption cooling system in terms of the Coefficient of performance (COP) and the Specific cooling power (SCP). On the other hand, if the switching time exceeds the optimal value, the performance of the adsorption cooling system is also reduced compared to that when using the optimal switching time. The dependency of the optimal switching times on various design parameters, such as the fin pitch, fin height and heating temperature, is also examined.

Effect of the switching time on the performance of an adsorption chiller

Energy Technology Data Exchange (ETDEWEB)

Hong, Sang Woo; Chung, Jae Dong [Sejong University, Seoul (Korea, Republic of); Kwon, Oh Kyung [Korea Institute of Industrial Technology, Chonan (Korea, Republic of)

2016-05-15

The switching time is an important operating condition that must be correctly anticipated for an effective adsorption cooling system. Before the adsorption (or desorption) process begins, time is required to cool down (or heat up) the bed temperature so that the bed pressure reaches the evaporator pressure (or condenser pressure). During the switching time, the supplied heat is reduced and pressure overload conditions can be avoided. The switching time cannot be estimated early on, and an improper switching time degrades the system performance. Thus, this study provides guideline with which to determine the required time to open this valve, i.e., the switching time, and carefully examines the thermo-physical behavior in the adsorption bed during this period. A two-dimensional numerical method with the composite sorbent of SWS-1L and a water pair is applied to a fin-tube type adsorption chiller. Three cases of no switching time, the optimal switching time and a double the optimal switching time are examined. The results show that no consideration of the switching time overestimates the performance of the adsorption cooling system in terms of the Coefficient of performance (COP) and the Specific cooling power (SCP). On the other hand, if the switching time exceeds the optimal value, the performance of the adsorption cooling system is also reduced compared to that when using the optimal switching time. The dependency of the optimal switching times on various design parameters, such as the fin pitch, fin height and heating temperature, is also examined.

Energy reversible switching from amorphous metal based nanoelectromechanical switch

KAUST Repository

Mayet, Abdulilah M.; Smith, Casey; Hussain, Muhammad Mustafa

2013-01-01

We report observation of energy reversible switching from amorphous metal based nanoelectromechanical (NEM) switch. For ultra-low power electronics, NEM switches can be used as a complementary switching element in many nanoelectronic system applications. Its inherent zero power consumption because of mechanical detachment is an attractive feature. However, its operating voltage needs to be in the realm of 1 volt or lower. Appropriate design and lower Young's modulus can contribute achieving lower operating voltage. Therefore, we have developed amorphous metal with low Young's modulus and in this paper reporting the energy reversible switching from a laterally actuated double electrode NEM switch. © 2013 IEEE.

Energy reversible switching from amorphous metal based nanoelectromechanical switch

KAUST Repository

Mayet, Abdulilah M.

2013-08-01

We report observation of energy reversible switching from amorphous metal based nanoelectromechanical (NEM) switch. For ultra-low power electronics, NEM switches can be used as a complementary switching element in many nanoelectronic system applications. Its inherent zero power consumption because of mechanical detachment is an attractive feature. However, its operating voltage needs to be in the realm of 1 volt or lower. Appropriate design and lower Young\\'s modulus can contribute achieving lower operating voltage. Therefore, we have developed amorphous metal with low Young\\'s modulus and in this paper reporting the energy reversible switching from a laterally actuated double electrode NEM switch. © 2013 IEEE.

PlasmaPy: initial development of a Python package for plasma physics

Science.gov (United States)

Murphy, Nicholas; Leonard, Andrew J.; Stańczak, Dominik; Haggerty, Colby C.; Parashar, Tulasi N.; Huang, Yu-Min; PlasmaPy Community

2017-10-01

We report on initial development of PlasmaPy: an open source community-driven Python package for plasma physics. PlasmaPy seeks to provide core functionality that is needed for the formation of a fully open source Python ecosystem for plasma physics. PlasmaPy prioritizes code readability, consistency, and maintainability while using best practices for scientific computing such as version control, continuous integration testing, embedding documentation in code, and code review. We discuss our current and planned capabilities, including features presently under development. The development roadmap includes features such as fluid and particle simulation capabilities, a Grad-Shafranov solver, a dispersion relation solver, atomic data retrieval methods, and tools to analyze simulations and experiments. We describe several ways to contribute to PlasmaPy. PlasmaPy has a code of conduct and is being developed under a BSD license, with a version 0.1 release planned for 2018. The success of PlasmaPy depends on active community involvement, so anyone interested in contributing to this project should contact the authors. This work was partially supported by the U.S. Department of Energy.

Optical switching based on the manipulation of microparticles in a colloidal liquid using strong scattering force

International Nuclear Information System (INIS)

Liu Jin; Liu Zheng-Qi; Feng Tian-Hua; Dai Qiao-Feng; Wu Li-Jun; Lan Sheng

2010-01-01

This paper demonstrates the realization of an optical switch by optically manipulating a large number of polystyrene spheres contained in a capillary. The strong scattering force exerted on polystyrene spheres with a large diameter of 4.3 μm is employed to realize the switching operation. A transparent window is opened for the signal light when the polystyrene spheres originally located at the beam centre are driven out of the beam region by the strong scattering force induced by the control light. The switching dynamics under different incident powers is investigated and compared with that observed in the optical switch based on the formation of optical matter. It is found that a large extinction ratio of ∼ 30 dB and fast switching-on and switching-off times can be achieved in this type of switch. (classical areas of phenomenology)

The dynamics of gas-puff imploding plasmas on the NRL Gamble II Generator

International Nuclear Information System (INIS)

Stephanakis, S.J.; Boller, J.R.; Hinshelwood, D.D.; McDonald, S.W.; Mehlman, C.G.; Ottinger, P.F.; Young, F.C.

1985-01-01

The experimental study of imploding plasma loads on the NRL Gamble II generator was initiated more than a year ago. Preliminary results including scaling laws for K-line radiation output from neon puffs and the effect of plasma erosion opening switches (PEOS's) on the x-ray yields and the pinch quality were reported upon during the past year. In order to better understand the implosion dynamics of such plasmas, time-resolved photographs have been taken of the implosion history. In contrast with time-integrated x-ray pinhole photographs, the time-resolved visible-light pictures indicate that the implosion phase is essentially instability-free, while pinching and flaring occur at late times during the blow-up phase. Furthermore, these visible-light framing photographs clearly show that the discharge is flared out toward the anode at early times and becomes cylindrical at implosion. This so-called ''zipper-effect'' has been seen in previous argon-puff experiments and is due to the non-uniform initial distribution of gas across the anode-cathode gap. The authors present comparisons of time-resolved photographs taken both in visible and x-ray light along with x-ray spectra taken with and without PEOS's. The implications of these data are discussed in view of the present theoretical understanding of the plasma implosion dynamics

The dynamics of gas-puff imploding plasmas on the NRL Gamble II generator

International Nuclear Information System (INIS)

Stephanakis, S.J.; Boller, J.R.; Hinshelwood, D.D.; McDonald, S.W.; Mehlman, C.G.; Ottinger, P.F.; Young, F.C.

1985-01-01

The experimental study of imploding plasma loads on the NRL Gamble II generator was initiated more than a year ago. Preliminary results including scaling laws for K-line radiation output from neon puffs and the effect of plasma erosion opening switches (PEOS's) on the x-ray yields and the pinch quality were reported upon during the past year. In order to better understand the implosion dynamics of such plasmas, time-resolved photographs have been taken of the implosion history. In contrast with time-integrated x-ray pinhole photographs, the time-resolved visible-light pictures indicate that the implosion phase is essentially instability-free, while pinching and flaring occur at late times during the blow-up phase. Furthermore, these visible-light framing photographs clearly show that the discharge is flared out toward the anode at early times and becomes cylindrical at implosion. This so-called ''zipper-effect'' has been seen in previous argon-puff experiments and is due to the non-uniform initial distribution of gas across the anode-cathode gap. The authors present comparisons of time-resolved photographs taken both in visible and x-ray light along with x-ray spectra taken with and without PEOS's. The implications of these data are discussed in view of the present theoretical understanding of the plasma implosion dynamics

Long-term efficacy and tolerability of quetiapine in patients with schizophrenia who switched from other antipsychotics because of inadequate therapeutic response-a prospective open-label study.

Science.gov (United States)

Hashimoto, Naoki; Toyomaki, Atsuhito; Honda, Minoru; Miyano, Satoru; Nitta, Nobuyuki; Sawayama, Hiroyuki; Sugawara, Yasufumi; Uemura, Keiichi; Tsukamoto, Noriko; Koyama, Tsukasa; Kusumi, Ichiro

2015-01-01

While the frequency and importance of antipsychotic switching in patients with schizophrenia, there is insufficient evidence with regard to switching strategy. Quetiapine is one of the drugs of choice for switch because of its unique receptor profile. However, there were no data on the long-term clinical and neurocognitive effect of quetiapine in patients who had responded inadequately to prior antipsychotics. The purpose of this study is to examine the long-term efficacy and tolerability of quetiapine in patients with schizophrenia who switched from other antipsychotics because of inadequate therapeutic response. We hypothesized that quetiapine would show long-term effectiveness in broad symptom dimensions including negative and neurocognitive symptoms while having good tolerability. Twenty-nine subjects with schizophrenia who did not respond to their current monotherapy of antipsychotic or who could not tolerate the treatment were switched to quetiapine and assessed at baseline and at 3, 6, and 12 months. The outcome measures included the brief assessment of cognition in schizophrenia (BACS), the Positive and Negative Syndrome Scale (PANSS), the Clinical Global Impressions Scale (CGI), the Schizophrenia Quality of Life Scale Japanese version (JSQLS), the Athens Insomnia Scale (AIS), and the Drug Attitude Inventory with 30 items (DAI-30). The Drug-Induced Extrapyramidal Symptoms Scale (DIEPSS), HbA1c, prolactin (PRL), and body weight were also evaluated. Statistically significant improvements were observed in all subscores of the PANSS, the GAF, and the symptoms and side effects subscale of the JSQLS, the DIEPSS, the AIS, and the PRL level, and nearly significant improvements were observed in the DAI-30. Quetiapine monotherapy was associated with significant improvement in the verbal memory test, even after controlling for the practice effect. Although quetiapine was well tolerated, three subjects dropped out because of the worsening of the psychotic symptoms and

Reduction of Tribocorrosion Products When using the Platform-Switching Concept.

Science.gov (United States)

Alrabeah, G O; Knowles, J C; Petridis, H

2018-03-01

The reduced marginal bone loss observed when using the platform-switching concept may be the result of reduced amounts of tribocorrosion products released to the peri-implant tissues. Therefore, the purpose of this study was to compare the tribocorrosion product release from various platform-matched and platform-switched implant-abutment couplings under cyclic loading. Forty-eight titanium implants were coupled with pure titanium, gold alloy, cobalt-chrome alloy, and zirconia abutments forming either platform-switched or platform-matched groups ( n = 6). The specimens were subjected to cyclic occlusal forces in a wet acidic environment for 24 h followed by static aqueous immersion for 6 d. The amount of metal ions released was measured using inductively coupled plasma mass spectrometry. Microscopic evaluations were performed pre- and postimmersion under scanning electron microscope (SEM) equipped with energy-dispersive spectroscopy X-ray for corrosion assessment at the interface and wear particle characterization. All platform-switched groups showed less metal ion release compared with their platform-matched counterparts within each abutment material group ( P concept in the reduction of tribocorrosion products released from dental implants, which consequently may minimize the adverse tissue reactions that lead to peri-implant bone loss.

Beam steering for circular switched parasitic arrays using a combinational approach

CSIR Research Space (South Africa)

Mofolo, ROM

2011-09-01

Full Text Available In this paper, the authors present a method of electronic beam steering for circular switched parasitic array (SPA) antennas. In circular SPA antennas, one achieves azimuth beam steering by open-circuiting and short-circuiting different parasitic...

Beam-plasma interaction with an electron beam injecting into a symmetrically open plasma system; Electron beam relaxation. Puchkovo-plazmennoe vzaimodejstvie pri inzhektsii ehlektronnogo puchka v simmetrichno otkrytuyu plazmennuyu sistemu; Relaksatsiya ehlektronnogo puchka

Energy Technology Data Exchange (ETDEWEB)

Opanasenko, A V; Romanyuk, L I [AN Ukrainskoj SSR, Kiev (Ukrainian SSR). Inst. Yadernykh Issledovanij

1989-10-01

The relaxation of the electron beam with the electron density of 1-2 keV injected through the symmetrically open plasma system with the independent hot cathode Penning discharge is experimentally investigated. It is shown that the velocity distribution function of the electron beam changes after passing each wave generation zone induced by the beam. The contribution of different wave zones to the beam relaxation depends on the prehistory of the beam-plasma interaction and may be regulated by the selection of the plasma system parameters. By this way the complete relaxation of the electron beam can be achieved after the beam crossing the whole system.

A packet switched communications system for GRO

Science.gov (United States)

Husain, Shabu; Yang, Wen-Hsing; Vadlamudi, Rani; Valenti, Joseph

1993-11-01

This paper describes the packet switched Instrumenters Communication System (ICS) that was developed for the Command Management Facility at GSFC to support the Gamma Ray Observatory (GRO) spacecraft. The GRO ICS serves as a vital science data acquisition link to the GRO scientists to initiate commands for their spacecraft instruments. The system is ready to send and receive messages at any time, 24 hours a day and seven days a week. The system is based on X.25 and the International Standard Organization's (ISO) 7-layer Open Systems Interconnection (OSI) protocol model and has client and server components. The components of the GRO ICS are discussed along with how the Communications Subsystem for Interconnection (CSFI) and Network Control Program Packet Switching Interface (NPSI) software are used in the system.

Interrogating vertically oriented carbon nanofibers with nanomanipulation for nanoelectromechanical switching applications

International Nuclear Information System (INIS)

Kaul, Anupama B.; Megerian, Krikor G.; LeDuc, Henry G.; Epp, Larry; Khan, Abdur R.; Bagge, Leif

2009-01-01

We have demonstrated electrostatic switching in vertically oriented carbon nanofibers synthesized on refractory metallic nitride substrates, where pull-in voltages V pi ranged from 10 to 40 V. A nanoprobe was used as the actuating electrode inside a scanning-electron microscope and van der Waals interactions at these length scales appeared significant, suggesting such structures are promising for nonvolatile memory applications. A finite element model was also developed to determine a theoretical V pi and results were compared to experiment. Nanomanipulation tests also revealed tubes synthesized directly on Si by dc plasma-enhanced chemical-vapor deposition with ammonia and acetylene were electrically unsuitable for dc nanoelectromechanical switching applications.

Bilingual Voicing: A Study of Code-Switching in the Reported Speech of Finnish Immigrants in Estonia

Science.gov (United States)

Frick, Maria; Riionheimo, Helka

2013-01-01

Through a conversation analytic investigation of Finnish-Estonian bilingual (direct) reported speech (i.e., voicing) by Finns who live in Estonia, this study shows how code-switching is used as a double contextualization device. The code-switched voicings are shaped by the on-going interactional situation, serving its needs by opening up a context…

Synchronization Between Two Different Switched Chaotic Systems By Switching Control

Directory of Open Access Journals (Sweden)

Du Li Ming

2016-01-01

Full Text Available This paper is concerned with the synchronization problem of two different switched chaotic systems, considering the general case that the master-slave switched chaotic systems have uncertainties. Two basic problems are considered: one is projective synchronization of switched chaotic systems under arbitrary switching; the other is projective synchronization of switched chaotic systems by design of switching when synchronization cannot achieved by using any subsystems alone. For the two problems, common Lyapunov function method and multiple Lyapunov function method are used respectively, an adaptive control scheme has been presented, some sufficient synchronization conditions are attainted, and the switching signal is designed. Finally, the numerical simulation is provide to show the effectiveness of our method.

A rotating arc plasma invertor

International Nuclear Information System (INIS)

Reusch, M.F.; Jayaram, K.

1987-02-01

A device is described for the inversion of direct current to alternating current. The main feature is the use of a rotating plasma arc in crossed electric and magnetic fields as a switch. This device may provide an economic alternative to other inversion methods in some circumstances

Exciter switch

Science.gov (United States)

Mcpeak, W. L.

1975-01-01

A new exciter switch assembly has been installed at the three DSN 64-m deep space stations. This assembly provides for switching Block III and Block IV exciters to either the high-power or 20-kW transmitters in either dual-carrier or single-carrier mode. In the dual-carrier mode, it provides for balancing the two drive signals from a single control panel located in the transmitter local control and remote control consoles. In addition to the improved switching capabilities, extensive monitoring of both the exciter switch assembly and Transmitter Subsystem is provided by the exciter switch monitor and display assemblies.

Nudging Leads Consumers In Colorado To Shop But Not Switch ACA Marketplace Plans.

Science.gov (United States)

Marzilli Ericson, Keith M; Kingsdale, Jon; Layton, Tim; Sacarny, Adam

2017-02-01

The Affordable Care Act (ACA) dramatically expanded the use of regulated marketplaces in health insurance, but consumers often fail to shop for plans during open enrollment periods. Typically these consumers are automatically reenrolled in their old plans, which potentially exposes them to unexpected increases in their insurance premiums and cost sharing. We conducted a randomized intervention to encourage enrollees in an ACA Marketplace to shop for plans. We tested the effect of letters and e-mails with personalized information about the savings on insurance premiums that they could realize from switching plans and the effect of generic communications that simply emphasized the possibility of saving. The personalized and generic messages both increased shopping on the Marketplace's website by 23 percent, but neither type of message had a significant effect on plan switching. These findings show that simple "nudges" with even generic information can promote shopping in health insurance marketplaces, but whether they can lead to switching remains an open question. Project HOPE—The People-to-People Health Foundation, Inc.

A Switch Is Not a Switch: Syntactically-Driven Bilingual Language Control

Science.gov (United States)

Gollan, Tamar H.; Goldrick, Matthew

2018-01-01

The current study investigated the possibility that language switches could be relatively automatically triggered by context. "Single-word switches," in which bilinguals switched languages on a single word in midsentence and then immediately switched back, were contrasted with more complete "whole-language switches," in which…

Switching Phenomena in a System with No Switches

Science.gov (United States)

Preis, Tobias; Stanley, H. Eugene

2010-02-01

It is widely believed that switching phenomena require switches, but this is actually not true. For an intriguing variety of switching phenomena in nature, the underlying complex system abruptly changes from one state to another in a highly discontinuous fashion. For example, financial market fluctuations are characterized by many abrupt switchings creating increasing trends ("bubble formation") and decreasing trends ("financial collapse"). Such switching occurs on time scales ranging from macroscopic bubbles persisting for hundreds of days to microscopic bubbles persisting only for a few seconds. We analyze a database containing 13,991,275 German DAX Future transactions recorded with a time resolution of 10 msec. For comparison, a database providing 2,592,531 of all S&P500 daily closing prices is used. We ask whether these ubiquitous switching phenomena have quantifiable features independent of the time horizon studied. We find striking scale-free behavior of the volatility after each switching occurs. We interpret our findings as being consistent with time-dependent collective behavior of financial market participants. We test the possible universality of our result by performing a parallel analysis of fluctuations in transaction volume and time intervals between trades. We show that these financial market switching processes have properties similar to those of phase transitions. We suggest that the well-known catastrophic bubbles that occur on large time scales—such as the most recent financial crisis—are no outliers but single dramatic representatives caused by the switching between upward and downward trends on time scales varying over nine orders of magnitude from very large (≈102 days) down to very small (≈10 ms).

Augmented switching linear dynamical system model for gas concentration estimation with MOX sensors in an open sampling system.

Science.gov (United States)

Di Lello, Enrico; Trincavelli, Marco; Bruyninckx, Herman; De Laet, Tinne

2014-07-11

In this paper, we introduce a Bayesian time series model approach for gas concentration estimation using Metal Oxide (MOX) sensors in Open Sampling System (OSS). Our approach focuses on the compensation of the slow response of MOX sensors, while concurrently solving the problem of estimating the gas concentration in OSS. The proposed Augmented Switching Linear System model allows to include all the sources of uncertainty arising at each step of the problem in a single coherent probabilistic formulation. In particular, the problem of detecting on-line the current sensor dynamical regime and estimating the underlying gas concentration under environmental disturbances and noisy measurements is formulated and solved as a statistical inference problem. Our model improves, with respect to the state of the art, where system modeling approaches have been already introduced, but only provided an indirect relative measures proportional to the gas concentration and the problem of modeling uncertainty was ignored. Our approach is validated experimentally and the performances in terms of speed of and quality of the gas concentration estimation are compared with the ones obtained using a photo-ionization detector.

Methodology, Measurement and Analysis of Flow Table Update Characteristics in Hardware OpenFlow Switches

KAUST Repository

Kuźniar, Maciej; Pereší ni, Peter; Kostić, Dejan; Canini, Marco

2018-01-01

and performance characteristics is essential for ensuring successful and safe deployments.We propose a systematic methodology for SDN switch performance analysis and devise a series of experiments based on this methodology. The methodology relies on sending a

A 0.2 V Micro-Electromechanical Switch Enabled by a Phase Transition.

Science.gov (United States)

Dong, Kaichen; Choe, Hwan Sung; Wang, Xi; Liu, Huili; Saha, Bivas; Ko, Changhyun; Deng, Yang; Tom, Kyle B; Lou, Shuai; Wang, Letian; Grigoropoulos, Costas P; You, Zheng; Yao, Jie; Wu, Junqiao

2018-04-01

Micro-electromechanical (MEM) switches, with advantages such as quasi-zero leakage current, emerge as attractive candidates for overcoming the physical limits of complementary metal-oxide semiconductor (CMOS) devices. To practically integrate MEM switches into CMOS circuits, two major challenges must be addressed: sub 1 V operating voltage to match the voltage levels in current circuit systems and being able to deliver at least millions of operating cycles. However, existing sub 1 V mechanical switches are mostly subject to significant body bias and/or limited lifetimes, thus failing to meet both limitations simultaneously. Here 0.2 V MEM switching devices with ≳10 6 safe operating cycles in ambient air are reported, which achieve the lowest operating voltage in mechanical switches without body bias reported to date. The ultralow operating voltage is mainly enabled by the abrupt phase transition of nanolayered vanadium dioxide (VO 2 ) slightly above room temperature. The phase-transition MEM switches open possibilities for sub 1 V hybrid integrated devices/circuits/systems, as well as ultralow power consumption sensors for Internet of Things applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Three-dimensional plasma transport in open chaotic magnetic fields. A computational assessment for tokamak edge layers

International Nuclear Information System (INIS)

Frerichs, Heinke Gerd

2010-04-01

The development of nuclear fusion as an alternative energy source requires the research on magnetically confined, high temperature plasmas. In particular, the quantification of plasma flows in the domain near exposed material surfaces of the plasma container by computer simulations is of key importance, both for guiding interpretation of present fusion experiments and for aiding the ongoing design activities for large future devices such as ITER, W7-X or the DEMO reactor. There is a large number of computational issues related to the physics of hot, fully ionized and magnetized plasmas near surfaces of the vacuum chamber. This thesis is dedicated to one particular such challenge, namely the numerical quantification of self-consistent kinetic neutral gas and plasma fluid flows in very complex 3D (partially chaotic) magnetic fields, in the absence of any common symmetries for plasma and neutral gas dynamics. Such magnetic field configurations are e.g. generated by externally applied magnetic perturbations at the plasma edge, and are of great interest for the control of particle and energy exhausts. In the present thesis the 3D edge plasma and neutral particle transport code EMC3-EIRENE is applied to two distinct configurations of open chaotic magnetic system: at the TEXTOR and DIII-D tokamaks. Improvements of the edge transport model and extensions of the transport code are presented, which have allowed such simulations for the first time for 3D scenarios at DIII-D with ITER similar plasmas. A strong 3D effect of the chaotic magnetic field on the DIII-D edge plasma is found and analyzed in detail. It is found that a pronounced striation pattern of target particle and heat fluxes at DIII-D can only be obtained up to a certain upper limiting level of anomalous cross-field transport. Hence, in comparison to experimental data, these findings allow to narrow down the range of this model parameter. One particular interest at TEXTOR is the achievement of a regime with

Operation of a homeostatic sleep switch.

Science.gov (United States)

Pimentel, Diogo; Donlea, Jeffrey M; Talbot, Clifford B; Song, Seoho M; Thurston, Alexander J F; Miesenböck, Gero

2016-08-18

Sleep disconnects animals from the external world, at considerable risks and costs that must be offset by a vital benefit. Insight into this mysterious benefit will come from understanding sleep homeostasis: to monitor sleep need, an internal bookkeeper must track physiological changes that are linked to the core function of sleep. In Drosophila, a crucial component of the machinery for sleep homeostasis is a cluster of neurons innervating the dorsal fan-shaped body (dFB) of the central complex. Artificial activation of these cells induces sleep, whereas reductions in excitability cause insomnia. dFB neurons in sleep-deprived flies tend to be electrically active, with high input resistances and long membrane time constants, while neurons in rested flies tend to be electrically silent. Correlative evidence thus supports the simple view that homeostatic sleep control works by switching sleep-promoting neurons between active and quiescent states. Here we demonstrate state switching by dFB neurons, identify dopamine as a neuromodulator that operates the switch, and delineate the switching mechanism. Arousing dopamine caused transient hyperpolarization of dFB neurons within tens of milliseconds and lasting excitability suppression within minutes. Both effects were transduced by Dop1R2 receptors and mediated by potassium conductances. The switch to electrical silence involved the downregulation of voltage-gated A-type currents carried by Shaker and Shab, and the upregulation of voltage-independent leak currents through a two-pore-domain potassium channel that we term Sandman. Sandman is encoded by the CG8713 gene and translocates to the plasma membrane in response to dopamine. dFB-restricted interference with the expression of Shaker or Sandman decreased or increased sleep, respectively, by slowing the repetitive discharge of dFB neurons in the ON state or blocking their entry into the OFF state. Biophysical changes in a small population of neurons are thus linked to the

Simultaneous determination of asperosaponin VI and its active metabolite hederagenin in rat plasma by liquid chromatography-tandem mass spectrometry with positive/negative ion-switching electrospray ionization and its application in pharmacokinetic study.

Science.gov (United States)

Zhu, He; Ding, Li; Shakya, Shailendra; Qi, Xiemin; Hu, Linlin; Yang, Xiaolin; Yang, Zhonglin

2011-11-15

A new liquid chromatography-tandem mass spectrometry (LC-MS/MS) method operated in the positive/negative electrospray ionization (ESI) switching mode has been developed and validated for the simultaneous determination of asperosaponin VI and its active metabolite hederagenin in rat plasma. After addition of internal standards diazepam (for asperosaponin VI) and glycyrrhetic acid (for hederagenin), the plasma sample was deproteinized with acetonitrile, and separated on a reversed phase C18 column with a mobile phase of methanol (solvent A)-0.05% glacial acetic acid containing 10 mM ammonium acetate and 30 μM sodium acetate (solvent B) using gradient elution. The detection of target compounds was done in multiple reaction monitoring (MRM) mode using a tandem mass spectrometry equipped with positive/negative ion-switching ESI source. At the first segment, the MRM detection was operated in the positive ESI mode using the transitions of m/z 951.5 ([M+Na](+))→347.1 for asperosaponin VI and m/z 285.1 ([M+H](+))→193.1 for diazepam for 4 min, then switched to the negative ESI mode using the transitions of m/z 471.3 ([M-H](-))→471.3 for hederagenin and m/z 469.4 ([M-H](-))→425.4 for glycyrrhetic acid, respectively. The sodiated molecular ion [M+Na](+) at m/z 951.5 was selected as the precursor ion for asperosaponin VI, since it provided better sensitivity compared to the deprotonated and protonated molecular ions. Sodium acetate was added to the mobile phase to make sure that abundant amount of the sodiated molecular ion of asperosaponin VI could be produced, and more stable and intensive mass response of the product ion could be obtained. For the detection of hederagenin, since all of the mass responses of the fragment ions were very weak, the deprotonated molecular ion [M-H](-)m/z 471.3 was employed as both the precursor ion and the product ion. But the collision energy was still used for the MRM, in order to eliminate the influences induced by the interference

Body weight - Open TG-GATEs | LSDB Archive [Life Science Database Archive metadata

Lifescience Database Archive (English)

Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data ...le URL: ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/open_tggates_body_...atabase Description Download License Update History of This Database Site Policy | Contact Us Body weight - Open TG-GATEs | LSDB Archive ...

EDITORIAL: Molecular switches at surfaces Molecular switches at surfaces

Science.gov (United States)

Weinelt, Martin; von Oppen, Felix

2012-10-01

In nature, molecules exploit interaction with their environment to realize complex functionalities on the nanometer length scale. Physical, chemical and/or biological specificity is frequently achieved by the switching of molecules between microscopically different states. Paradigmatic examples are the energy production in proton pumps of bacteria or the signal conversion in human vision, which rely on switching molecules between different configurations or conformations by external stimuli. The remarkable reproducibility and unparalleled fatigue resistance of these natural processes makes it highly desirable to emulate nature and develop artificial systems with molecular functionalities. A promising avenue towards this goal is to anchor the molecular switches at surfaces, offering new pathways to control their functional properties, to apply electrical contacts, or to integrate switches into larger systems. Anchoring at surfaces allows one to access the full range from individual molecular switches to self-assembled monolayers of well-defined geometry and to customize the coupling between molecules and substrate or between adsorbed molecules. Progress in this field requires both synthesis and preparation of appropriate molecular systems and control over suitable external stimuli, such as light, heat, or electrical currents. To optimize switching and generate function, it is essential to unravel the geometric structure, the electronic properties and the dynamic interactions of the molecular switches on surfaces. This special section, Molecular Switches at Surfaces, collects 17 contributions describing different aspects of this research field. They analyze elementary processes, both in single molecules and in ensembles of molecules, which involve molecular switching and concomitant changes of optical, electronic, or magnetic properties. Two topical reviews summarize the current status, including both challenges and achievements in the field of molecular switches on

Temperature and density profiles of an MHD switch-on shock

International Nuclear Information System (INIS)

Watson-Munro, C.N.; Bighel, L.; Collins, A.R.; Cramer, N.F.; Cross, R.C.

1975-01-01

An experimental study of the structure of MHD switch-on shock waves propagating into partially ionized hydrogen and helium plasmas is described. The variation of electron and ion temperatures through the shock front was studied as a function of the level of pre-ionization. When the shock propagates into an almost fully ionized plasma, the electron temperature rises well above the ion temperature owing to resistive heating of the electrons. At low pre-ionization levels, however, the ion temperature rises above the electron temperature. These results indicate that ion-neutral collisions can play a dominant role in the dissipation of energy in a shock wave. (author)

A fast switch, combiner and narrow-band filter for high-power millimetre wave beams

Science.gov (United States)

Kasparek, W.; Petelin, M. I.; Shchegolkov, D. Yu; Erckmann, V.; Plaum, B.; Bruschi, A.; ECRH Groups at IPP Greifswald; Karlsruhe, FZK; Stuttgart, IPF

2008-05-01

A fast directional switch (FADIS) is described, which allows controlled switching of high-power microwaves between two outputs. A possible application could be synchronous stabilization of neoclassical tearing modes (NTMs). Generally, the device can be used to share the installed EC power between different types of launchers or different applications (e.g. in ITER, midplane/upper launcher). The switching is performed electronically without moving parts by a small frequency-shift keying of the gyrotron (some tens of megahertz), and a narrow-band diplexer. The device can be operated as a beam combiner also, which offers attractive transmission perspectives in multi-megawatt ECRH systems. In addition, these diplexers are useful for plasma diagnostic systems employing high-power sources due to their filter characteristics. The principle and the design of a four-port quasi-optical resonator diplexer is presented. Low-power measurements of switching contrast, mode purity and efficiency show good agreement with theory. Preliminary frequency modulation characteristics of gyrotrons are shown, and first results from high-power switching experiments using the ECRH system for W7-X are presented.

A fast switch, combiner and narrow-band filter for high-power millimetre wave beams

International Nuclear Information System (INIS)

Kasparek, W.; Plaum, B.; Petelin, M.I.; Shchegolkov, D.Yu; Erckmann, V.; Bruschi, A.

2008-01-01

A fast directional switch (FADIS) is described, which allows controlled switching of high-power microwaves between two outputs. A possible application could be synchronous stabilization of neoclassical tearing modes (NTMs). Generally, the device can be used to share the installed EC power between different types of launchers or different applications (e.g. in ITER, midplane/upper launcher). The switching is performed electronically without moving parts by a small frequency-shift keying of the gyrotron (some tens of megahertz), and a narrow-band diplexer. The device can be operated as a beam combiner also, which offers attractive transmission perspectives in multi-megawatt ECRH systems. In addition, these diplexers are useful for plasma diagnostic systems employing high-power sources due to their filter characteristics. The principle and the design of a four-port quasi-optical resonator diplexer is presented. Low-power measurements of switching contrast, mode purity and efficiency show good agreement with theory. Preliminary frequency modulation characteristics of gyrotrons are shown, and first results from high-power switching experiments using the ECRH system for W7-X are presented

Effect of switching-off of a plasma medium on a traveling wave

International Nuclear Information System (INIS)

Kalluri, D.K.

1989-01-01

It is known that a sudden creation of a plasma medium of plasma frequency ω ρ splits a traveling wave of frequency ω o into two new waves of frequencies. The negative value for the frequency here indicates a reflected wave. The effect of a sudden collapse of the plasma medium, on a travelling wave of frequency ω o is shown to be the creation of two new waves of frequencies. A numerical solution is obtained for the case of a gradual collapse of the plasma medium. For the case of a slow decay of the particle density an approximate WKB type solution is obtained. Several results are presented

No switch to coal-based feedstocks until 2000

Energy Technology Data Exchange (ETDEWEB)

1977-06-10

This is a resume of a paper ''Organics for the 1980s-petrochemicals or coal chemicals'' by S. P. S. Andrew. There will be no significant switch from petrochemicals to coal-based chemicals worldwide until well into the 21st century, when synthetic gasoline could be made in the U. S. from open-cast coal. Processes are being developed for converting coal to gasoline, ethylene, and ammonia.

Investigation of electrically exploded large area foil for current switching

International Nuclear Information System (INIS)

Chernyshev, V.K.; Boyko, A.M.; Kostyukov, V.N.; Kuzyaev, A.I.; Kulagin, A.A.; Mamyshev, V.I.; Mezhevov, A.B.; Nechaev, A.I.; Petrukhin, A.A.; Protasov, M.S.; Shevtsov, V.I.; Yakubov, V.B.

1990-01-01

The possibility of microsecond ∼40 MA current switching from EMG into a quasiconstant inductive load by an electrically exploded foil is investigated. The copper foil of large area, S ∼ 10 4 cm 2 , was placed between thin-walled insulators into a coaxial transmission line (TL). This paper shows a conceptual device scheme. To feed a foil opening switch (FOS), a disc explosive magnetic generator (DEMG) with 20 μs current rise time was employed. An inductive coaxial load was connected to a FOS at a moment, that was close to the foil vaporization start by means of an axisymmetric explosive current commutator (ECC)

Plasma position control device

International Nuclear Information System (INIS)

Takase, Haruhiko.

1987-01-01

Purpose: To conduct position control stably to various plasmas and reduce the burden on the control coil power source. Constitution: Among the proportional, integration and differentiation controls, a proportional-differentiation control section and an integration control section are connected in parallel. Then, a signal switching circuit is disposed to the control signal input section for the proportional-differentiation control section such that either a present position of plasmas or deviation between the present plasma position and an aimed value can be selected as a control signal depending on the control procedures or the state of the plasmas. For instance, if a rapid response is required for the control, the deviation between the present plasma position and the aimed value is selected as the input signal to conduct proportional, integration and differentiation controls. While on the other hand, if it is intended to reduce the burden on the control coil power source, it is adapted such that the control signal inputted to the proportional-differentiation control section itself can select the present plasma position. (Yoshihara, H.)

The {open_quotes}first{close_quotes} problem

Energy Technology Data Exchange (ETDEWEB)

Holsinger, R.F.

1995-02-01

This paper describes the first magnet design problem that Klaus and the author worked on together. At the time, over 30 years ago, Klaus was working as a plasma physicist in the Controlled Thermonuclear Research (CTR) Group, and the author was assigned from the Mechanical Engineering Department to help with the design of experimental equipment for various research projects. Klaus` primary research program was to develop a {open_quotes}plasma gun{close_quotes} for injecting plasma into {open_quotes}mirror machines.{close_quotes} As described, the magnet design aspect of this plasma gun was a challenging task, and led to some innovations that were quite advanced at that time.

Optimal control of switching time in switched stochastic systems with multi-switching times and different costs

Science.gov (United States)

Liu, Xiaomei; Li, Shengtao; Zhang, Kanjian

2017-08-01

In this paper, we solve an optimal control problem for a class of time-invariant switched stochastic systems with multi-switching times, where the objective is to minimise a cost functional with different costs defined on the states. In particular, we focus on problems in which a pre-specified sequence of active subsystems is given and the switching times are the only control variables. Based on the calculus of variation, we derive the gradient of the cost functional with respect to the switching times on an especially simple form, which can be directly used in gradient descent algorithms to locate the optimal switching instants. Finally, a numerical example is given, highlighting the validity of the proposed methodology.

Assumption or Fact? Line-to-Neutral Voltage Expression in an Unbalanced 3-Phase Circuit during Inverter Switching

Science.gov (United States)

Masrur, M. A.

2009-01-01

This paper discusses the situation in a 3-phase motor or any other 3-phase system operating under unbalanced operating conditions caused by an open fault in an inverter switch. A dc voltage source is assumed as the input to the inverter, and under faulty conditions of the inverter switch, the actual voltage applied between the line to neutral…

Comparative effectiveness of switching paroxetine formulation for treatment of major depressive disorder: an open-label multicenter study

Directory of Open Access Journals (Sweden)

Otsubo T

2018-04-01

Full Text Available Tempei Otsubo,1 Yoshinori Watanabe,2,3 Seiji Hongo,3 Mikichika Inoue,4 Kimiko Akimoto,4 Ken Murakami,5 Ryutaro Takahashi,6 Toshiaki Kikuchi7 1Department of Psychiatry, Tokyo Women’s Medical University Medical Center East, Tokyo, Japan; 2Himorogi Psychiatric Institute, Tokyo, Japan; 3Nanko Clinic of Psychiatry, Shirakawa, Japan; 4Ikebukuro Internal Medicine, Tokyo, Japan; 5Murakami Hospital, Tokyo, Japan; 6Takahashi Clinic, Tokyo, Japan; 7Department of Neuropsychiatry, Keio University School of Medicine, Tokyo, Japan Aim: To assess the effectiveness and safety of switching the antidepressant formulation from immediate-release (IR to controlled-release (CR paroxetine in patients with major depressive disorder (MDD. Patients and methods: A total of 113 outpatients with MDD diagnosed according to the Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition, Text Revision, and treated with a stable dose of IR paroxetine for at least 6 months were enrolled. Patients were then switched to CR paroxetine for 8 weeks. Effectiveness was evaluated by scores on the Himorogi Self-Rating Depression/Anxiety Scales (HSDS/HSAS and the Clinical Global Impression – Severity (CGI-S. Safety was evaluated based on the reported adverse drug reactions (ADRs. Medication satisfaction and preference were assessed based on questionnaire responses using Likert-type scales. Results: The overall patient HSDS/HSAS scores significantly improved after switching from IR to CR paroxetine (P<0.001. Furthermore, CR paroxetine was superior to IR paroxetine (P<0.001 according to the results of the CGI-S evaluation. ADRs were experienced by 14 (12.4% patients, including dry mouth, nausea/vomiting, somnolence/drowsiness, and wakefulness/arousal during sleep. Satisfaction and preference for paroxetine improved after switching to the CR formulation (P<0.001; chi-square test. Conclusion: These results suggest that switching the treatment from IR to CR paroxetine could

A plasma switch synchronous closing operations in high-voltage networks

International Nuclear Information System (INIS)

Mourente, P.

1984-01-01

Overvoltages and overcurrent arising in energizing or in fast reclosing operations are a concerning problem in high-voltage networks. Reduction of overvoltages and overcurrents is possible using the synchronous closing technique. Some attempts have been done to perform the synchronous closing with conventional circuit-breakers. But since the requirements to synchronous closing and to current interruption are very contradictory this technique is not yet a common practice. Three simple cases may be used as examples to show the benefits of synchronous closing; energizaton of grounded star capacitor bank; back-to-back switching of large capacitor banks; and fast reclosing on transmission lines

Differential coulometric oxidation following post column-switching high pressure liquid chromatography for fluorescence measurement of unmetabolized folic acid in human plasma.

Science.gov (United States)

Bailey, Steven W; Ayling, June E

2013-11-08

Although many countries have fortified their grain supplies with folic acid (FA) to decrease the incidence of neural tube defects, others have not due to concerns that this synthetic folate might have some adverse effects. Persistent unmetabolized FA has been found even in plasma from fasted subjects. To facilitate measurement of low levels of folic acid in human plasma, post-column coulometric oxidative cleavage was used to convert poorly fluorescent FA into a highly fluorescent compound determined to be 6-formyl-pterin. To minimize sample work-up and maximize recovery, column-switching HPLC transferred a window of eluate containing the FA from the first column (C8) onto a second column (phenyl-hexyl). The pH of two mobile phases were adjusted to be above and then below a pK of the FA α-carboxyl group, thus promoting separation from compounds coeluting from the C8-column. This permitted sample preparation using only a simple high recovery protein precipitation. Definitive identification of FA in human plasma was accomplished by duplicate injections of sample with the electrochemical voltage set above and below its half-potential. The LOD (S/N=3) was 0.10 nM. The intra- and inter-assay CV's were 2.3% and 5%, respectively. Comparison of these results with those obtained by HPLC/MS/MS with stable isotope internal standard showed a slope of 1.00 ± 0.019. This simple, sensitive, and repeatable assay facilitates a more thorough investigation of the response of various human populations to folic acid intake. Post-column differential coulometric electrochemistry can expand the variety of compounds amenable to fluorescence detection. Copyright © 2013 Elsevier B.V. All rights reserved.

Modelling of new generation plasma optical devices

Directory of Open Access Journals (Sweden)

Litovko Irina V.

2016-06-01

Full Text Available The paper presents new generation plasma optical devices based on the electrostatic plasma lens configuration that opens a novel attractive possibility for effective high-tech practical applications. Original approaches to use of plasma accelerators with closed electron drift and open walls for the creation of a cost-effective low-maintenance plasma lens with positive space charge and possible application for low-cost, low-energy rocket engine are described. The preliminary experimental, theoretical and simulation results are presented. It is noted that the presented plasma devices are attractive for many different applications in the state-of-the-art vacuum-plasma processing.

Soft controller switching technique to minimize the torque and current pulsations of a SCIM during its reswitching

International Nuclear Information System (INIS)

Larik, A.S.

2010-01-01

The direct-on-line starting of induction motor draws heavy current and to limit this Inrush current to a safe level normally a star-delta switch is used. However, the switching over from star to delta causes over current transients and this leads to torque pulsations. Therefore, in this paper the current and torque pulsations developed during the switching process are focused and a soft-switched controller is devised to minimize the re-closure transient currents and torque pulsations during star-delta switching of induction motor. The designed system can readily handles the sensing of favorable conditions of re closure of a switched-off running induction motor and it minimizes the inrush current and hence the pulsations of torque of all types of induction motors, whether, single-phase or three phase. An investigation is made into the transient currents and pulsation torques generated due to opening the circuit of a running induction motor and the switching pattern of star-delta switching. The re-switching control scheme for the induction motor is practically tested in the laboratory with and without soft controller. (author)

Long conduction time POs experiments on MITE

International Nuclear Information System (INIS)

Woodall, H.N.; McDaniel, D.H.; Mendel, C.W.; Rochau, G.E.; Zagar, D.M.; Simpson, W.W.; Zuchowski, N.P.

1990-01-01

MITE is a power flow test bed that has been modified to conduct experiments in high power plasma opening switch (POS) technology and apply this technology to Inertial Confinement Fusion. The goal of the experiment is to develop a plasma opening switch that conducts megampere currents for 300 ns, then opens in 5--10 ns. MITE/POS is an advanced power flow experiment that uses a magnetically insulated transmission line (MITL) as the inductive energy store and as a means to shape the output pulse. This experiment demonstrates that a simplified, lower-cost facility can be built by eliminating water pulse-forming lines and water-switching. Another advantage of this approach is that high energy efficiency at peak power can be achieved. The disadvantage is that a new technology, the triggered POS, must be implemented. The triggered POS is necessary for synchronization of multiple modules with a long conduction-time POS. The MITE facility has been modified to drive a 250 nH, 16.6 Ohm MITL at 0.9 MA to accommodate this power flow experiment. A MITL inductive energy storage of 101 kJ is available for POS switching to a matched load. Experiments have been conducted using segmented flashboards and magnetic-field controlled plasma sources. These experiments will lead to the development of the triggered POS. The initial experiments with plasma conduction times of 120 ns to 800 ns are discussed

Reconfigurable Plasma Antenna Array by Using Fluorescent Tube for Wi-Fi Application

Directory of Open Access Journals (Sweden)

H. Ja’afar

2016-06-01

Full Text Available This paper presents a new design of reconfigurable plasma antenna array using commercial fluorescent tube. A round shape reconfigurable plasma antenna array is proposed to collimate beam radiated by an omnidirectional antenna (monopole antenna operates at 2.4GHz in particular direction. The antenna design is consisted of monopole antenna located at the center of circular aluminum ground. The monopole antenna is surrounded by a cylindrical shell of conducting plasma. The plasma shield consists of 12 commercial fluorescent tubes aligned in series containing a mixture of Argon gas and mercury vapor which upon electrification forms plasma columns. The plasma behaves as a conductor and acts as a reflector in radiation, in the condition where plasma frequency,ωp is higher than operating frequency. From this concepts, when all plasma elements are activated or switched to ON, the radiation signal from monopole antenna will trapped inside the plasma blanket and meanwhile when one or more plasma elements is deactivated (switched OFF, the radiation from monopole antenna will escape. This antenna has the capability to change its patterns with beam direction at 0°, 30°, 60°, 90°, 120°, 150°, 180°, 210°, 240°, 270°, 300° and 330° at frequency 2.4 GHz. The proposed antenna has been successfully fabricated and measured with conclusive results.

Measurement of trigger and cascade section runtimes in 6 MV switches using fiber coupled photodetectors

Directory of Open Access Journals (Sweden)

Jens Schwarz

2012-07-01

Full Text Available Since October 2007 Sandia National Laboratories has operated the refurbished Z machine at an improved load current of 26 MA yielding 400 TW of x-ray power. The current pulse shape to the load is controlled by 36 independently timed laser triggered gas switches. As part of the refurbishment effort, a fiber coupled laser spark detector system has been installed which is able to detect the laser generated plasma in situ inside the trigger section of the high voltage switch. In this paper we describe how this detection system can be used to characterize the discharge dynamics of these 5.9 MV, 820 kA switches.

The association of the effect of lithium in the maintenance treatment of bipolar disorder with lithium plasma levels : a post hoc analysis of a double-blind study comparing switching to lithium or placebo in patients who responded to quetiapine (Trial 144)

NARCIS (Netherlands)

Nolen, Willem A.; Weisler, Richard H.

Nolen WA, Weisler RH. The association of the effect of lithium in the maintenance treatment of bipolar disorder with lithium plasma levels: a post hoc analysis of a double-blind study comparing switching to lithium or placebo in patients who responded to quetiapine (Trial 144). Bipolar Disord 2012:

Electromagnetic-wave absorption by inhomogeneous, collisional plasmas

International Nuclear Information System (INIS)

Gregoire, D.J.; Santoru, J.; Schumacher, R.W.

1990-01-01

Unmagnetized, collisional plasmas can be used as broadband EM-wave absorbers or refractors. In the absorption process, plasma electrons are first accelerated by the EM-wave fields and then collide with background-gas molecules, thereby transferring energy from the EM waves to the gas. A plasma absorber has several advantages compared to conventional materials. A plasma can be turned on and off very rapidly, thereby switching between absorbing and transparent conditions. Calculations indicate that plasma absorbers can also be tailored to provide broadband absorption (>40 dB) over multiple octaves. The authors have developed a one-dimensional model and a computer code to calculate the net power reflected from a plasma-enclosed EM-wave-reflecting target. They included three contributions to the reflected EM-wave power: reflections from the vacuum-plasma interface; reflections from the bulk plasma volume; and reflection of the attenuated EM wave that is transmitted through the plasma and reflected by the target

Traction Inverter Open Switch Fault Diagnosis Based on Choi–Williams Distribution Spectral Kurtosis and Wavelet-Packet Energy Shannon Entropy

Directory of Open Access Journals (Sweden)

Shuangshuang Lin

2017-09-01

Full Text Available In this paper, a new approach for fault detection and location of open switch faults in the closed-loop inverter fed vector controlled drives of Electric Multiple Units is proposed. Spectral kurtosis (SK based on Choi–Williams distribution (CWD as a statistical tool can effectively indicate the presence of transients and locations in the frequency domain. Wavelet-packet energy Shannon entropy (WPESE is appropriate for the transient changes detection of complex non-linear and non-stationary signals. Based on the analyses of currents in normal and fault conditions, SK based on CWD and WPESE are combined with the DC component method. SK based on CWD and WPESE are used for the fault detection, and the DC component method is used for the fault localization. This approach can diagnose the specific locations of faulty Insulated Gate Bipolar Transistors (IGBTs with high accuracy, and it requires no additional devices. Experiments on the RT-LAB platform are carried out and the experimental results verify the feasibility and effectiveness of the diagnosis method.

Digital switched hydraulics

Science.gov (United States)

Pan, Min; Plummer, Andrew

2018-06-01

This paper reviews recent developments in digital switched hydraulics particularly the switched inertance hydraulic systems (SIHSs). The performance of SIHSs is presented in brief with a discussion of several possible configurations and control strategies. The soft switching technology and high-speed switching valve design techniques are discussed. Challenges and recommendations are given based on the current research achievements.

Enhancement of resistive switching properties in Al2O3 bilayer-based atomic switches: multilevel resistive switching

Science.gov (United States)

Vishwanath, Sujaya Kumar; Woo, Hyunsuk; Jeon, Sanghun

2018-06-01

Atomic switches are considered to be building blocks for future non-volatile data storage and internet of things. However, obtaining device structures capable of ultrahigh density data storage, high endurance, and long data retention, and more importantly, understanding the switching mechanisms are still a challenge for atomic switches. Here, we achieved improved resistive switching performance in a bilayer structure containing aluminum oxide, with an oxygen-deficient oxide as the top switching layer and stoichiometric oxide as the bottom switching layer, using atomic layer deposition. This bilayer device showed a high on/off ratio (105) with better endurance (∼2000 cycles) and longer data retention (104 s) than single-oxide layers. In addition, depending on the compliance current, the bilayer device could be operated in four different resistance states. Furthermore, the depth profiles of the hourglass-shaped conductive filament of the bilayer device was observed by conductive atomic force microscopy.

Potential formation in a collisionless plasma produced in an open magnetic field in presence of volume negative ion source

International Nuclear Information System (INIS)

Phukan, Ananya; Goswami, K. S.; Bhuyan, P. J.

2014-01-01

The electric potential near a wall for a multi-species plasma with volume produced negative ions in presence of axially varying magnetic field is studied following an analytical-numerical approach. A constant negative ion source is assumed throughout the plasma volume, along with finite temperature positive ions and Boltzmann electrons. The particles are assumed to be guided by an open magnetic field that has its maximum at the centre, and field strength decreasing towards the walls. The one dimensional (1D) Poisson equation is derived using an analytical approach, and then solved numerically to study the potential profiles. Effect of (a) negative ion production rate, (b) magnetic field profile, and (c) negative ion temperature on the potential profile has been investigated. A potential peak appears near the wall when the negative ion temperature and density are sufficiently high. Also, the presence of negative ions further decreases the potential in the plasma region for a finite Debye Length (λ D )

Intentional preparation of auditory attention-switches: Explicit cueing and sequential switch-predictability.

Science.gov (United States)

Seibold, Julia C; Nolden, Sophie; Oberem, Josefa; Fels, Janina; Koch, Iring

2018-06-01

In an auditory attention-switching paradigm, participants heard two simultaneously spoken number-words, each presented to one ear, and decided whether the target number was smaller or larger than 5 by pressing a left or right key. An instructional cue in each trial indicated which feature had to be used to identify the target number (e.g., female voice). Auditory attention-switch costs were found when this feature changed compared to when it repeated in two consecutive trials. Earlier studies employing this paradigm showed mixed results when they examined whether such cued auditory attention-switches can be prepared actively during the cue-stimulus interval. This study systematically assessed which preconditions are necessary for the advance preparation of auditory attention-switches. Three experiments were conducted that controlled for cue-repetition benefits, modality switches between cue and stimuli, as well as for predictability of the switch-sequence. Only in the third experiment, in which predictability for an attention-switch was maximal due to a pre-instructed switch-sequence and predictable stimulus onsets, active switch-specific preparation was found. These results suggest that the cognitive system can prepare auditory attention-switches, and this preparation seems to be triggered primarily by the memorised switching-sequence and valid expectations about the time of target onset.

Direct Synthesis of Carbon Nanotube Field Emitters on Metal Substrate for Open-Type X-ray Source in Medical Imaging

Directory of Open Access Journals (Sweden)

Amar Prasad Gupta

2017-07-01

Full Text Available We report the design, fabrication and characterization of a carbon nanotube enabled open-type X-ray system for medical imaging. We directly grew the carbon nanotubes used as electron emitter for electron gun on a non-polished raw metallic rectangular-rounded substrate with an area of 0.1377 cm2 through a plasma enhanced chemical vapor deposition system. The stable field emission properties with triode electrodes after electrical aging treatment showed an anode emission current of 0.63 mA at a gate field of 7.51 V/μm. The 4.5-inch cubic shape open type X-ray system was developed consisting of an X-ray aperture, a vacuum part, an anode high voltage part, and a field emission electron gun including three electrodes with focusing, gate and cathode electrodes. Using this system, we obtained high-resolution X-ray images accelerated at 42–70 kV voltage by digital switching control between emitter and ground electrode.

Direct Synthesis of Carbon Nanotube Field Emitters on Metal Substrate for Open-Type X-ray Source in Medical Imaging.

Science.gov (United States)

Gupta, Amar Prasad; Park, Sangjun; Yeo, Seung Jun; Jung, Jaeik; Cho, Chonggil; Paik, Sang Hyun; Park, Hunkuk; Cho, Young Chul; Kim, Seung Hoon; Shin, Ji Hoon; Ahn, Jeung Sun; Ryu, Jehwang

2017-07-29

We report the design, fabrication and characterization of a carbon nanotube enabled open-type X-ray system for medical imaging. We directly grew the carbon nanotubes used as electron emitter for electron gun on a non-polished raw metallic rectangular-rounded substrate with an area of 0.1377 cm² through a plasma enhanced chemical vapor deposition system. The stable field emission properties with triode electrodes after electrical aging treatment showed an anode emission current of 0.63 mA at a gate field of 7.51 V/μm. The 4.5-inch cubic shape open type X-ray system was developed consisting of an X-ray aperture, a vacuum part, an anode high voltage part, and a field emission electron gun including three electrodes with focusing, gate and cathode electrodes. Using this system, we obtained high-resolution X-ray images accelerated at 42-70 kV voltage by digital switching control between emitter and ground electrode.

Cognitive processes and neural basis of language switching: proposal of a new model.

Science.gov (United States)

Moritz-Gasser, Sylvie; Duffau, Hugues

2009-12-09

Although studies on bilingualism are abundant, cognitive processes and neural foundations of language switching received less attention. The aim of our study is to provide new insights to this still open question: do dedicated region(s) for language switching exist or is this function underlain by a distributed circuit of interconnected brain areas, part of a more general cognitive system? On the basis of recent behavioral, neuroimaging, and brain stimulation studies, we propose an original 'hodological' model of language switching. This process might be subserved by a large-scale cortico-subcortical network, with an executive system (prefrontal cortex, anterior cingulum, caudate nucleus) controlling a more dedicated language subcircuit, which involves postero-temporal areas, supramarginal and angular gyri, Broca's area, and the superior longitudinal fasciculus.

Reduced Fluorescent Protein Switching Fatigue by Binding-Induced Emissive State Stabilization

Directory of Open Access Journals (Sweden)

Thijs Roebroek

2017-09-01

Full Text Available Reversibly switchable fluorescent proteins (RSFPs enable advanced fluorescence imaging, though the performance of this imaging crucially depends on the properties of the labels. We report on the use of an existing small binding peptide, named Enhancer, to modulate the spectroscopic properties of the recently developed rsGreen series of RSFPs. Fusion constructs of Enhancer with rsGreen1 and rsGreenF revealed an increased molecular brightness and pH stability, although expression in living E. coli or HeLa cells resulted in a decrease of the overall emission. Surprisingly, Enhancer binding also increased off-switching speed and resistance to switching fatigue. Further investigation suggested that the RSFPs can interconvert between fast- and slow-switching emissive states, with the overall protein population gradually converting to the slow-switching state through irradiation. The Enhancer modulates the spectroscopic properties of both states, but also preferentially stabilizes the fast-switching state, supporting the increased fatigue resistance. This work demonstrates how the photo-physical properties of RSFPs can be influenced by their binding to other small proteins, which opens up new horizons for applications that may require such modulation. Furthermore, we provide new insights into the photoswitching kinetics that should be of general consideration when developing new RSFPs with improved or different photochromic properties.

Note: Switching crosstalk on and off in Kelvin probe force microscopy

International Nuclear Information System (INIS)

Polak, Leo; Wijngaarden, Rinke J.; Man, Sven de

2014-01-01

In Kelvin Probe Force Microscopy (KPFM) electronic crosstalk can occur between the excitation signal and probe deflection signal. Here, we demonstrate how a small modification to our commercial instrument enables us to literally switch the crosstalk on and off. We study in detail the effect of crosstalk on open-loop KPFM and compare with closed-loop KPFM. We measure the pure crosstalk signal and verify that we can correct for it in the data-processing required for open-loop KPFM. We also demonstrate that open-loop KPFM results are independent of the frequency and amplitude of the excitation signal, provided that the influence of crosstalk has been eliminated

MVA amplifier used for plasma position control in the WEGA tokamak

International Nuclear Information System (INIS)

Schenk, G.

1982-02-01

A new amplifier has been developed for the control of the plasma positron in the WEGA III tokomak acting on the vertical magnetic field. In the high power domain thyristor choppers are usually applied. Unfortunately their response time is quite long and does not yet correspond to the WEGA demand. Therefore transistors have been used to build a fast switching amplifier of the H-bridge type, delivering a power of 1 MVA, by switching 2500 A at 400 V. Because of the duty cycle of the plasma (0,12 s every 240 s) the necessary average power to the amplifier supply is only 500 VA. An intermediate energy storage in an electrolytic capacitor bank is therefore used. As the switching transistors must operate under extreme conditions of voltage and current, precautions must be taken to limit the overvoltage and the overcurrent, to prevent oscillations and to assure power and control equilibrium among the transistors

Temperature dependent electron transport and rate coefficient studies for e-beam-sustained diffuse gas discharge switching

International Nuclear Information System (INIS)

Carter, J.G.; Hunter, S.R.; Christophorou, L.G.

1987-01-01

Measurements of the electron drift velocity, w, attachment coefficient, eta/N/sub a/, and ionization coefficient, α/N, have been made in C 2 F 6 /Ar and C 2 F 6 /CH 4 gas mixtures at gas temperatures, T, of 300 and 500 0 K over the concentration range of 0.1 to 100% of the C 2 F 6 . These measurements are useful for modeling the expected behavior of repetitively operated electron-beam sustained diffuse gas discharge opening switches where gas temperatures within the switch are anticipated to rise several hundred degrees during switch operation

Design of foil implosion system for Pioneer I experiments

International Nuclear Information System (INIS)

Erickson, D.J.; Caird, R.S.; Fowler, C.M.

1985-01-01

A foil implosion system is described that integrates an explosive flux-compression generator, a flat plate feed section with power conditioning switches, and a vacuum electrode region containing a cylindrical foil/plasma load. Power conditioning, obtained with an explosive-driven plasma compression opening switch and explosive-actuated closing switches, provides a submicrosecond multimegampere pulse for the implosion of an aluminum plasma. The flat plate section is configured for bidirectional feed to the coaxial vacuum electrodes. Important considerations in the design of the vacuum power flow region include gap failure, feed symmetry, and radial diagnostic access. The system presently accommodates a foil radius of 3 cm. Innovative foil insertion and clamping techniques are also described

Parallel transport of long mean-free-path plasma along open magnetic field lines: Parallel heat flux

International Nuclear Information System (INIS)

Guo Zehua; Tang Xianzhu

2012-01-01

In a long mean-free-path plasma where temperature anisotropy can be sustained, the parallel heat flux has two components with one associated with the parallel thermal energy and the other the perpendicular thermal energy. Due to the large deviation of the distribution function from local Maxwellian in an open field line plasma with low collisionality, the conventional perturbative calculation of the parallel heat flux closure in its local or non-local form is no longer applicable. Here, a non-perturbative calculation is presented for a collisionless plasma in a two-dimensional flux expander bounded by absorbing walls. Specifically, closures of previously unfamiliar form are obtained for ions and electrons, which relate two distinct components of the species parallel heat flux to the lower order fluid moments such as density, parallel flow, parallel and perpendicular temperatures, and the field quantities such as the magnetic field strength and the electrostatic potential. The plasma source and boundary condition at the absorbing wall enter explicitly in the closure calculation. Although the closure calculation does not take into account wave-particle interactions, the results based on passing orbits from steady-state collisionless drift-kinetic equation show remarkable agreement with fully kinetic-Maxwell simulations. As an example of the physical implications of the theory, the parallel heat flux closures are found to predict a surprising observation in the kinetic-Maxwell simulation of the 2D magnetic flux expander problem, where the parallel heat flux of the parallel thermal energy flows from low to high parallel temperature region.

Development of modular scalable pulsed power systems for high power magnetized plasma experiments

Science.gov (United States)

Bean, I. A.; Weber, T. E.; Adams, C. S.; Henderson, B. R.; Klim, A. J.

2017-10-01

New pulsed power switches and trigger drivers are being developed in order to explore higher energy regimes in the Magnetic Shock Experiment (MSX) at Los Alamos National Laboratory. To achieve the required plasma velocities, high-power (approx. 100 kV, 100s of kA), high charge transfer (approx. 1 C), low-jitter (few ns) gas switches are needed. A study has been conducted on the effects of various electrode geometries and materials, dielectric media, and triggering strategies; resulting in the design of a low-inductance annular field-distortion switch, optimized for use with dry air at 90 psig, and triggered by a low-jitter, rapid rise-time solid-state Linear Transformer Driver. The switch geometry and electrical characteristics are designed to be compatible with Syllac style capacitors, and are intended to be deployed in modular configurations. The scalable nature of this approach will enable the rapid design and implementation of a wide variety of high-power magnetized plasma experiments. This work is supported by the U.S. Department of Energy, National Nuclear Security Administration. Approved for unlimited release, LA-UR-17-2578.

INTERRAD - inductive terawatt X-ray generator (project)

Energy Technology Data Exchange (ETDEWEB)

Popkov, N F; Pikar` , A S; Kargin, V I; Ryaslov, E A; Lyubomirskij, A G [All-Russian Scientific Research Inst. of Experimental Physics, Sarov (Russian Federation)

1997-12-31

The results are given of the development and experimental research of explosive electron beam accelerator circuits powered by magneto-cumulative generators forming the current pulse, using explosive plasma opening switches. The conceptual lay-out of inductive terawatt X-ray generators powered by EMGs is proposed. The calculation results of the terawatt x-ray generator including the load placed in a special bunker are presented. Analyzed are the losses at the stage of the HE energy conversion into that of the magnetic fields, those occur ing in transmission along the high-voltage cable line, as well as the processes developing in the plasma opening switches. (author). 2 figs., 6 refs.

Combustion mode switching with a turbocharged/supercharged engine

Science.gov (United States)

Mond, Alan; Jiang, Li

2015-09-22

A method for switching between low- and high-dilution combustion modes in an internal combustion engine having an intake passage with an exhaust-driven turbocharger, a crankshaft-driven positive displacement supercharger downstream of the turbocharger and having variable boost controllable with a supercharger bypass valve, and a throttle valve downstream of the supercharger. The current combustion mode and mass air flow are determined. A switch to the target combustion mode is commanded when an operating condition falls within a range of predetermined operating conditions. A target mass air flow to achieve a target air-fuel ratio corresponding to the current operating condition and the target combustion mode is determined. The degree of opening of the supercharger bypass valve and the throttle valve are controlled to achieve the target mass air flow. The amount of residual exhaust gas is manipulated.

Demonstration of Ultra-Fast Switching in Nano metallic Resistive Switching Memory Devices

International Nuclear Information System (INIS)

Yang, Y.

2016-01-01

Interdependency of switching voltage and time creates a dilemma/obstacle for most resistive switching memories, which indicates low switching voltage and ultra-fast switching time cannot be simultaneously achieved. In this paper, an ultra-fast (sub-100 ns) yet low switching voltage resistive switching memory device (“nano metallic ReRAM”) was demonstrated. Experimental switching voltage is found independent of pulse width (intrinsic device property) when the pulse is long but shows abrupt time dependence (“cliff”) as pulse width approaches characteristic RC time of memory device (extrinsic device property). Both experiment and simulation show that the onset of cliff behavior is dependent on physical device size and parasitic resistance, which is expected to diminish as technology nodes shrink down. We believe this study provides solid evidence that nano metallic resistive switching memory can be reliably operated at low voltage and ultra-fast regime, thus beneficial to future memory technology.

Flipping the Metabolic Switch: Understanding and Applying Health Benefits of Fasting

Science.gov (United States)

Anton, Stephen D.; Moehl, Keelin; Donahoo, William T.; Marosi, Krisztina; Lee, Stephanie; Mainous, Arch G.; Leeuwenburgh, Christiaan; Mattson, Mark P.

2017-01-01

Intermittent fasting (IF) is a term used to describe a variety of eating patterns in which no or few calories are consumed for time periods that can range from 12 hours to several days, on a recurring basis. Here we focus on the physiological responses of major organ systems, including the musculoskeletal system, to the onset of the metabolic switch – the point of negative energy balance at which liver glycogen stores are depleted and fatty acids are mobilized (typically beyond 12 hours after cessation of food intake). Emerging findings suggest the metabolic switch from glucose to fatty acid-derived ketones represents an evolutionarily conserved trigger point that shifts metabolism from lipid/cholesterol synthesis and fat storage to mobilization of fat through fatty acid oxidation and fatty-acid derived ketones, which serve to preserve muscle mass and function. Thus, IF regimens that induce the metabolic switch have the potential to improve body composition in overweight individuals. Moreover, IF regimens also induce the coordinated activation of signaling pathways that optimize physiological function, enhance performance, and slow aging and disease processes. Future randomized controlled IF trials should use biomarkers of the metabolic switch (e.g., plasma ketone levels) as a measure of compliance and the magnitude of negative energy balance during the fasting period. PMID:29086496

Nongyrotropic particle distributions in space plasmas

Directory of Open Access Journals (Sweden)

U. Motschmann

1999-05-01

Full Text Available In nonstationary, strong inhomogeneous or open plasmas particle orbits are rather complicated. If the nonstationary time scale is smaller than the gyration period, if the inhomogeneity scale is smaller than the gyration radius, i.e. at magnetic plasma boundaries, or if the plasma has sources and sinks in phase space, then nongyrotropic distribution functions occur. The stability of such plasma configurations is studied in the framework of linear dispersion theory. In an open plasma nongyrotropy drives unstable waves parallel and perpendicular to the background magnetic field, whereas in the gyrotropic limit the plasma is stable. In nonstationary plasmas nongyrotropy drives perpendicular unstable waves only. Temporal modulation couples a seed mode with its side lobes and thus it renders unstable wave growth more difficult. As an example of an inhomogeneous plasma a magnetic halfspace is discussed. In a layer with thickness of the thermal proton gyroradius a nongyrotropic distribution is formed which may excite unstable parallel and perpendicular propagating waves.Key words. Interplanetary physics (plasma waves and turbulence · Ionosphere (plasma waves and instabilities · Magnetospheric physics (plasma waves and instabilities

Plasma igniter for internal combustion engine

Science.gov (United States)

Fitzgerald, D. J.; Breshears, R. R. (Inventor)

1978-01-01

An igniter for the air/fuel mixture used in the cylinders of an internal combustion engine is described. A conventional spark is used to initiate the discharge of a large amount of energy stored in a capacitor. A high current discharge of the energy in the capacitor switched on by a spark discharge produces a plasma and a magnetic field. The resultant combined electromagnetic current and magnetic field force accelerates the plasma deep into the combustion chamber thereby providing an improved ignition of the air/fuel mixture in the chamber.

Taming Instabilities in Plasma Discharges

International Nuclear Information System (INIS)

Klinger, T.; Krahnstover, N. O.; Mausbach, T.; Piel, A.

2000-01-01

Recent experimental work on taming instabilities in plasma discharges is discussed. Instead of suppressing instabilities, it is desired to achieve control over their dynamics, done by perturbing appropriately the current flow in the external circuit of the discharge. Different discrete and continuous feedback as well as open-loop control schemes are applied. Chaotic oscillations in plasma diodes are controlled using the OGY discrete feedback scheme. This is demonstrated both in experiment and computer simulation. Weakly developed ionization wave turbulence is tamed by continuous feedback control. Open-loop control of stochastic fluctuations - stochastic resonance - is demonstrated in a thermionic plasma diode. (author)

DESAIN DAN IMPLEMENTSI SOFT SWITCHING BOOST KONVERTER DENGAN SIMPLE AUXILLARY RESONANT SWITCH (SARC

Directory of Open Access Journals (Sweden)

Dimas Bagus Saputra

2017-01-01

Full Text Available Boost konverter merupakan penaik tegangan DC ke tegangan DC yang mempunyai tegangan output yang lebih tinggi dibanding inputnya. Penggunaan boost konverter diera modern semakin meningkat dan dibuat dengan dimensi yang lebih kecil, berat yang lebih ringan dan efisiensi yang lebih tinggi dibanding dengan boost konverter generasi terdahulu. Tetapi rugi-rugi periodik saat on/off meningkat. Untuk meraih kriteria tersebut, teknik hard switching boost konverter berevolusi menjadi teknik soft switching dengan menambah rangkaian simple auxiliary resonant circuit (SARC. Karena penambahan rangkaian SARC tersebut konverter bekerja pada kondisi zero-voltage switching switch (ZVS dan zero current switch (ZCS, sehingga saklar semikonduktor tidak bekerja secara hard switching lagi. Pada penelitian ini akan di desain dan diimplementaskan soft switching boost konverter dengan SARC. Kelebihan dari soft switching boost konverter dengan SARC adalah mempunyai efisiensi yang lebih tinggi dibanding dengan boost konverter konventional. Dari hasil implementasi menunjukkan konverter yang diajukan telah meraih zero voltage switch (ZVS. Sehingga boost konverter zero voltage switch (ZVS bisa diaplikasikan pada sistem power suplay yang membutuhkan efisiensi energi yang tinggi terutama pada daya yang tinggi.

Forget about switching keyboard layouts with the "Compose Key"

CERN Multimedia

CERN. Geneva

2018-01-01

Growing up with a Spanish keyboard was not an easy childhood (using Shift+7 (/) to search in vim, or having to type AltGr+[ to actually have an opening bracket), so at some point in my life I switched to an American keyboard. At the beginning I was happy switching layouts to either do some coding or talk to my mum (I am not a fan of the classical excuse "sorry for my typos, I don't have the 'ñ' in my keyboard"). Things got much worse when I started to need French characters (ç, è) to interact with some services at CERN, or some Slovak letters (č, đ) to talk to Robert, my Slovak colleague . Then I discovered the Compose Key and my life has been different ever since.

Development of a plasma retropulse shutter for Shiva and Nova

International Nuclear Information System (INIS)

Bradley, L.P.; Orham, E.L.; Stowers, I.F.; Koert, P.

1979-01-01

A plasma shutter is being developed for a Nd:glass laser fusion system which, at an output spatial filter pinhole, produces a plasma of 10 21 cm -3 to block target-reflected light from reentering the laser. A pulser using low-inductance capacitors and elastomer dielectric is switched with uv preilluminated railgaps to resistively heat a wire producing a plasma. The plasma generated within a nozzle and configured in a railgun geometry is projected across the optical beam path at 3.9 cm/μs. The optics are protected from the plasma. A scaled experiment is characterized, and a prototype shutter module is described

All-fiber optical mode switching based on cascaded mode selective couplers for short-reach MDM networks

Science.gov (United States)

Ren, Fang; Li, Juhao; Wu, Zhongying; Yu, Jinyi; Mo, Qi; Wang, Jianping; He, Yongqi; Chen, Zhangyuan; Li, Zhengbin

2017-04-01

We propose and experimentally demonstrate an all-fiber optical mode switching structure supporting independent switching, exchanging, adding, and dropping functionalities in which each mode can be switched individually. The mode switching structure consists of cascaded mode selective couplers (MSCs) capable of exciting and selecting specific higher order modes in few-mode fibers with high efficiency and one multiport optical switch routing the independent spatial modes to their destinations. The data carried on three different spatial modes can be switched, exchanged, added, and dropped through this all-fiber structure. For this experimental demonstration, optical on-off-keying (OOK) signals at 10-Gb/s carried on three spatial modes are successfully processed with open and clear eye diagrams. The mode switch exhibits power penalties of less than 3.1 dB after through operation, less than 2.7 dB after exchange operation, less than 2.8 dB after switching operation, and less than 1.6 dB after mode adding and dropping operations at the bit-error rate (BER) of 10-3, while all three channels carried on three spatial modes are simultaneously routed. The proposed structure, compatible with current optical switching networks based on single-mode fibers, can potentially be used to expand the switching scalability in advanced and flexible short-reach mode-division multiplexing-based networks.

Saturated Switching Systems

CERN Document Server

Benzaouia, Abdellah

2012-01-01

Saturated Switching Systems treats the problem of actuator saturation, inherent in all dynamical systems by using two approaches: positive invariance in which the controller is designed to work within a region of non-saturating linear behaviour; and saturation technique which allows saturation but guarantees asymptotic stability. The results obtained are extended from the linear systems in which they were first developed to switching systems with uncertainties, 2D switching systems, switching systems with Markovian jumping and switching systems of the Takagi-Sugeno type. The text represents a thoroughly referenced distillation of results obtained in this field during the last decade. The selected tool for analysis and design of stabilizing controllers is based on multiple Lyapunov functions and linear matrix inequalities. All the results are illustrated with numerical examples and figures many of them being modelled using MATLAB®. Saturated Switching Systems will be of interest to academic researchers in con...

100 kV solid-state switch for fusion heating systems

International Nuclear Information System (INIS)

Beaumont, B.; Bertrand, E.; Brugnetti, R.; Chatroux, D.; Kazarian, F.; Milly, R.; Prou, M.; Rigole, H.

2005-01-01

Power switching in RF heating systems is a delicate function as it is often linked to high power tube protection. In most RF systems, the end stage power tube is fed by a high voltage power supply (HVPS), which connection to the tube has to be interrupted in case of arc suspicion. The amount of energy that is allowable to be dissipated in the arc is in the range of 10-50 J, to limit the degradations observed on the tube structures. The protection function is usually performed by a crowbar. Furthermore, the HVPS is often shared by several power tubes, and the loss of all the power from the group of tubes is to be avoided to minimize the perturbation on the plasma experiment. A description of a 40 kV thyristor based crowbar and a 100 kV, 25 A MOSFET switch is given, as well as the contours of the existing components for high power switching applications. By combining small components, such as thyristors or MOSFET, in matrix, highly compact and reliable units have been built and implemented in Tore Supra RF systems

Light-activated resistance switching in SiOx RRAM devices

Science.gov (United States)

Mehonic, A.; Gerard, T.; Kenyon, A. J.

2017-12-01

We report a study of light-activated resistance switching in silicon oxide (SiOx) resistive random access memory (RRAM) devices. Our devices had an indium tin oxide/SiOx/p-Si Metal/Oxide/Semiconductor structure, with resistance switching taking place in a 35 nm thick SiOx layer. The optical activity of the devices was investigated by characterising them in a range of voltage and light conditions. Devices respond to illumination at wavelengths in the range of 410-650 nm but are unresponsive at 1152 nm, suggesting that photons are absorbed by the bottom p-type silicon electrode and that generation of free carriers underpins optical activity. Applied light causes charging of devices in the high resistance state (HRS), photocurrent in the low resistance state (LRS), and lowering of the set voltage (required to go from the HRS to LRS) and can be used in conjunction with a voltage bias to trigger switching from the HRS to the LRS. We demonstrate negative correlation between set voltage and applied laser power using a 632.8 nm laser source. We propose that, under illumination, increased electron injection and hence a higher rate of creation of Frenkel pairs in the oxide—precursors for the formation of conductive oxygen vacancy filaments—reduce switching voltages. Our results open up the possibility of light-triggered RRAM devices.

A compact plasmonic MOS-based 2×2 electro-optic switch

Directory of Open Access Journals (Sweden)

Ye Chenran

2015-01-01

Full Text Available We report on a three-waveguide electro-optic switch for compact photonic integrated circuits and data routing applications. The device features a plasmonic metal-oxide-semiconductor (MOS mode for enhanced light-matter-interactions. The switching mechanism originates from a capacitor-like design where the refractive index of the active medium, indium-tin-oxide, is altered via shifting the plasma frequency due to carrier accumulation inside the waveguide-based MOS structure. This light manipulation mechanism controls the transmission direction of transverse magnetic polarized light into either a CROSS or BAR waveguide port. The extinction ratio of 18 (7 dB for the CROSS (BAR state, respectively, is achieved via a gating voltage bias. The ultrafast broadband fJ/bit device allows for seamless integration with silicon-on-insulator platforms for low-cost manufacturing.

Bimetallic nanoparticles for surface modification and lubrication of MEMS switch contacts

International Nuclear Information System (INIS)

Patton, Steven T; Hu Jianjun; Slocik, Joseph M; Campbell, Angela; Naik, Rajesh R; Voevodin, Andrey A

2008-01-01

Reliability continues to be a critical issue in microelectromechanical systems (MEMS) switches. Failure mechanisms include high contact resistance (R), high adhesion, melting/shorting, and contact erosion. Little previous work has addressed the lubrication of MEMS switches. In this study, bimetallic nanoparticles (NPs) are synthesized using a biotemplated approach and deposited on Au MEMS switch contacts as a nanoparticle-based lubricant. Bimetallic nanoparticles are comprised of a metallic core (∼10 nm diameter gold nanoparticle) with smaller metallic nanoparticles (∼2-3 nm diameter Pd nanoparticles) populating the core surface. Adhesion and resistance (R) were measured during hot switching experiments at low (10 μA) and high (1 mA) current. The Au/Pd NP coated contacts led to reduced adhesion as compared to pure Au contacts with a compromise of slightly higher R. For switches held in the closed position at low current, R gradually decreased over tens of seconds due to increased van der Waals force and growth of the real area of contact with temporal effects being dominant over load effects. Contact behavior transitioned from 'Pd-like' to 'Au-like' during low current cycling experiments. Melting at high current resulted in rapid formation of large real contact area, low and stable R, and minimal effect of load on R. Durability at high current was excellent with no failure through 10 6 hot switching cycles. Improvement at high current is due to controlled nanoscale surface roughness that spreads current through multiple nanocontacts, which restricts the size of melting regions and causes termination of nanowire growth (prevents shorting) during contact opening. Based on these results, bimetallic NPs show excellent potential as surface modifiers/lubricants for MEMS switch contacts

Switch-shock wave structure in a magnetized partly-ionized gas

International Nuclear Information System (INIS)

Cramer, N.F.

1975-01-01

The effect of the interaction of plasma and neutral gas on the structure of switch-type shock waves propagating in a partly-ionized gas is studied. These shocks, in which the magnetic field is perpendicular to the shock front either upstream or downstream, exhibit a spiralling behaviour of the magnetic field in the shock transition region, if the Hall term is important in the Ohm's law. Observations of this behaviour for shocks propagating into a plasma with a residual neutral content of about 15% has implied an anomalously high resistivity of the plasma. We show that this can be partly explained by considering the collisions of ions with the neutral atoms in a magnetic field. We show that the extra dissipation due to the increase in resistivity goes primarily to the ions and neutrals. Thus even in the absence of viscous dissipation within each species, the heavy particles can be appreciably heated in a shock propagating into a partly-ionized gas in a magnetic field. (author)

Diagnostics of Plasma Jet Generated in Water/Argon DC Arc Torch.

Czech Academy of Sciences Publication Activity Database

Hurba, Oleksiy; Hlína, Michal; Hrabovský, Milan

2016-01-01

Roč. 3, č. 1 (2016), s. 5-8 ISSN 2336-2626. [Symposium on Physics of Switching Arc 2015, FSO 2015 /21./. Nové Město na Moravě, 07.09.2015-11.09.2015] R&D Projects: GA ČR(CZ) GA15-19444S Institutional support: RVO:61389021 Keywords : thermal plasma jet * electric probes * schlieren photography * enthalpy probe Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics)

Low risk of inhibitor formation in haemophilia A patients following en masse switch in treatment to a third generation full length plasma and albumin-free recombinant factor VIII product (ADVATE®).

LENUS (Irish Health Repository)

Bacon, C L

2011-05-01

Previous studies have suggested that development of inhibitors in previously treated patients (PTPs) may be attributable to a switch in factor VIII (FVIII) therapeutic product. Consequently, it is widely recognized that inhibitor development must be assessed in PTPs following the introduction of any new FVIII product. Following a national tender process in 2006, all patients with haemophilia A in Ireland changed their FVIII treatment product en masse to a plasma and albumin-free recombinant full-length FVIII product (ADVATE(®)). In this study, we retrospectively reviewed the case records of Irish PTPs to evaluate risk of inhibitor formation following this treatment switch. One hundred and thirteen patients participated in the study. Most patients (89%) had severe haemophilia. Only one of 96 patients with no inhibitor history developed an inhibitor. Prior to the switch in his recombinant FVIII (rFVIII) treatment of choice, this child had only experienced three exposure days (EDs). Consequently, in total he had only received 6 EDs when his inhibitor was first diagnosed. In keeping with this lack of de novo inhibitor development, we observed no evidence of any recurrent inhibitor formation in any of 16 patients with previously documented inhibitors. Similarly, following a previous en masse switch, we have previously reported that changing from a Chinese hamster ovary cell-produced to a baby hamster kidney cell-produced rFVIII was also associated with a low risk of inhibitor formation in PTPs. Our cumulative findings from these two studies clearly emphasizes that the risk of inhibitor development for PTPs following changes in commercial rFVIII product is low, at least in the Irish population.

Atmospheric plasma generation for LCD panel cleaning

Science.gov (United States)

Kim, Gyu-Sik; Won, Chung-Yuen; Choi, Ju-Yeop; Yim, C. H.

2007-12-01

UV lamp systems have been used for cleaning of display panels of TFT LCD or Plasma Display Panel (PDP). However, the needs for high efficient cleaning and low cost made high voltage plasma cleaning techniques to be developed and to be improved. Dielectric-barrier discharges (DBDs), also referred to as barrier discharges or silent discharges have for a long time been exclusively related to ozone generation. In this paper, a 6kW high voltage plasma power supply system was developed for LCD cleaning. The -phase input voltage is rectified and then inverter system is used to make a high frequency pulse train, which is rectified after passing through a high-power transformer. Finally, bi-directional high voltage pulse switching circuits are used to generate the high voltage plasma. Some experimental results showed the usefulness of atmospheric plasma for LCD panel cleaning.

Interference mitigation enhancement of switched-based scheme in over-loaded femtocells

KAUST Repository

Gaaloul, Fakhreddine

2012-06-01

This paper proposes adequate methods to improve the interference mitigation capability of a recently investigated switched-based interference reduction scheme in short-range open-access and over-loaded femtocells. It is assumed that the available orthogonal channels for the femtocell network are distributed among operating access points in close vicinity, where each of which knows its allocated channels a priori. For the case when the feedback links are capacity-limited and the available channels can be universally shared and simultaneously used, the paper presents enhanced schemes to identify a channel to serve the desired scheduled user by maintaining the interference power level within a tolerable range. They attempt to either complement the switched-based scheme by minimum interference channel selection or adopt different interference thresholds on available channels, while aiming to reduce the channels examination load. The performance of the proposed schemes is quantified and then compared with those of the single-threshold switched-based scheme via numerical and simulation results. © 2012 IEEE.

The electrical Discharge Characteristics of the 3.5 KJ Electrothermal Plasma Gun Experiment