WorldWideScience

Sample records for plants vaegledning foer

  1. Guidance for emergency planning in nuclear power plants; Vaegledning foer insatsplanering i kaerntekniska anlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Magnusson, Tommy; Ekdahl, Maria (Ringhals AB, Vaeroebacka (Sweden))

    2008-06-15

    Ringhals has been a model for this study, but the purpose has been to make the report applicable at all nuclear power plants in Sweden. The work has been done in close co-operation with the Swedish nuclear power plants and Rescue Services in the nuclear power municipalities Oesthammar, Oskarshamn, and Varberg. The internal fire brigade at the nuclear power plants has also been involved. A document will also be published as a further guidance at efforts of the type fires, which are mentioned in the enclosed document. After a fire in a switchgear room in 2005 the need of making the existing effort planning more effective at nuclear power plants was observed. The idea with the planning is to plan the effort in order to give the operational and emergency staff a good and actual support to come to a decision and to start the mission without delay. The risk information is showed by planning layouts, symbols and drawings as basis, give risk information and effort information. The effort information shows outer arrangements, manual action points, fire installations, passive fire safety etc. The risk information is shown by risk symbols. Their purpose is to give a fast overview of the existing risks. Reactor safety effects is the ruling influence if an effort has to be done in order to secure safety for a third person. In order to make an effort in an area personal risks for rescue staff, such as electricity risks, radiological risks, chemicals and gas bottles with compressed gases, has to be eliminated. For complicated missions detailed instructions are needed in order to handle specific risks. In a group discussion different people with pertinent knowledge has to value which problematic efforts need detailed instruction. Missions that have to be analyzed in a work group as above are: fire may affect the reactor safety, fire that may threaten the structural integrity, chemical discharge with big consequence on environment/third person and handling of gas system (compressed

  2. Microbiologic handbook for biogas plants; Mikrobiologisk handbok foer biogasanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Jarvis, Aasa; Schnuerer, Anna

    2009-05-15

    There is today great interest in the biogas process. The reason for interest is that this process offers an opportunity to stabilize and reduce various types of organic waste, while also generating clean renewable energy in the form of biogas. Purified biogas is a good alternative to gasoline and diesel as motor fuel and can also be used for heating and electricity production. Behind efficient biogas production lies a complex microbiological process. For biogas to be formed many different species of microorganisms have to be active. A disturbance of this teamwork leads to a reduction in biogas production or in the worst case that the process stops. In order to operate a biogas process in an efficient manner, it is necessary to have knowledge of the underlying microbiology and how microorganisms function. Today Swedish biogas plants have personnel with great technical knowledge, while the biological knowledge often is more limited. It has been difficult to find appropriate Swedish language literature in the field. This handbook aims to increase the microbiological expertise of staff at the biogas plants and thus to facilitate the stable operation and optimization of gas production

  3. Investigation of the responsibility for decommissioning of the Ranstad plant; Utredning av ansvaret foer Ranstadsverkets avveckling

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Haakan; Grundfelt, Bertil [Kemakta Konsult AB, Stockholm (Sweden); Froeberg, Magnus [Froeberg och Lundholm Advokatbyraa AB, Stockholm (Sweden)

    2010-11-15

    The issue of decommissioning, including demolition, of the nuclear facility at the Ranstad plant was raised gradually during 2006-2008. It was then found that it was unclear which company or companies that could be responsible for this decommissioning, economically as well as for the implementation. During this time and until the end of 2009, the concerned authorities, notably Swedish Nuclear Power Inspectorate and SSM, collected a large amount of facts as a basis for assessing liability. This material now needed to be systematized and compiled in order to effectively be utilized in such an assessment. SSM also thought that it would be helpful if an independent party with experience in similar issues could contribute to the interpretation of the legal situation. These were the given conditions of the mission which Kemakta Konsult AB, with the assistance of lawyer Magnus Froeberg, were given by SSM in the autumn of 2009. The results are presented in this final report.

  4. Guidance to regulations on trade with emission permits for carbon dioxide; Vaegledning till lagstiftning om handel med utslaeppsraetter foer koldioxid

    Energy Technology Data Exchange (ETDEWEB)

    2008-07-15

    This guidance is intended to facilitate application of the rules on emissions trading. The guidance is principally concerned with issues relating to permit appraisal and monitoring, but also discusses some terms common to permits and allocations, such as installation and operator. The guidance follows the same structure as the Swedish Environmental Protection Agency regulations (NFS 2007:5) in order to provide direct support for the rules. The focus is on providing a general description of the responsibilities of the operator and application of the rules. In addition, some difficult terms and relationships are explained. However, no exhaustive description of the operator's responsibilities is given, nor are the rules on verification described. We therefore recommend that the guidance should be read in conjunction with the Trading Act, the Trading Ordinance and the Swedish Environmental Protection Agency regulations. The first chapter presents a brief description of the purpose of the trading scheme, and is followed by a chapter in which the rules on applying for permits and the application procedure are reviewed. The next chapter gives a description of how the operator should monitor emissions and how the rules for the monitoring plan work, as well as the options that exist for simplified monitoring. The next chapter looks at notifications the operator might have to make and what they should contain. Guidance is also provided on how the county administrative board should process these notifications. The conditions of the permit decision are also briefly described. This is followed by a short chapter on the emissions report and the materiality threshold. The final chapter comments on certain parts of the annexes to the regulations. The EU Emissions Trading Directive has been implemented in Sweden through the Emissions Trading Act (2004:1199) (the Trading Act), the Emissions Trading Ordinance (2004:1205), the Swedish Environmental Protection Agency regulations (NFS 2007:5) and general recommendations on carbon dioxide emission allowances and the Swedish Energy Agency regulations (STEMFS 2004:8) on an emission allowance registry. All these documents can be found at www.utslappshandel.se

  5. Study of flue gas condensing for biofuel fired heat and power plants; Studie av roekgaskondensering foer biobraensleeldade kraftvaermeanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Axby, Fredrik; Gustafsson, J O; Nystroem, Johan; Johansson, Kent

    2000-11-01

    This report considers questions regarding flue gas condensing plants connected to bio-fuelled heat and power plants. The report consists of two parts, one where nine existing plants are described regarding technical issues and regarding the experience from the different plants. Part two is a theoretical study where heat balance calculations are made to show the technical and economical performance in different plant configurations and operating conditions. Initially the different parts in the flue gas condensing plant are described. Tube, plate and scrubber condensers are described briefly. The different types of humidifiers are also described, rotor, cross-stream plate heat exchanger and scrubber. Nine flue gas-condensing plants have been visited. The plants where chosen considering it should be bio-fuel fired plant primarily heat and power plants. Furthermore we tried to get a good dissemination considering plant configuration, supplier, geographical position, operating situation and plant size. The description of the different plants focuses on the flue gas condenser and the belonging components. The fuel, flue gas and condensate composition is described as well as which materials are used in the different parts of the plant. The experience from operating the plants and the reasons of why they decided to chose the actual condenser supplier are reported.

  6. Predictive emission monitoring system (PEMS) for emission control in biomass fired plants; Predikterande emissionsmaetsystem (PEMS) foer emissionskontroll i biobraensleeldade foerbraenningsanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Harnevie, H; Sarkoezi, L; Trenkle, S

    1996-08-01

    An alternative method for estimation of NO{sub x}-emissions from biomass fired plants has been investigated. The method, `Predictive emission monitoring` (PEMS), implicates the creation of a mathematical formula. The formula expresses the relations between NO{sub x}-emissions and various operating and external parameters, such as flue gas temperature, excess combustion air and heat load. In this study the applicability of PEMS has been tested for two plants both of type travelling stokers. The most important results of the study are: PEMS is suitable for emission monitoring for some types of biomass fired plants (for example travelling stokers) even if the plant is fired with fuel with varying water content. In most cases it should be sufficient if the relation is based on oxygen level in the flue gas and plant load, with the possible addition of flue gas temperature and/or furnace temperature rate. These parameters are usually measured in any case, which means that no additional investment in instrumentation is necessary. In this study many measured parameters (for example the throttle levels) did not affect the NO{sub x}-emissions. A PEMS relation is only applicable for a specific plant and for a fixed validity range. Thus the function should be performed in such a way that it covers the limits of the operating parameters of the plant. Usage of different fuels or drift optimization can only be done within the validity range. Good combustion conditions could be necessary to receive a usable PEMS-function. Before creating the PEMS-function the combustion and the emission levels must be optimized. In plants with very fluctuating combustion, for example fixed stokers, it is possible that PEMS leads to not satisfying results. The total cost for a PEM-function can be calculated to be about 50-70% compared to a CEM during a period of a decade. 8 refs, 13 figs, 15 tabs, 8 appendices

  7. Combustion plants and the Water Framework Directive. Methodology for consequence assessment; Vaermeanlaeggningar och Vattendirektivet. Metodik foer konsekvensbedoemning

    Energy Technology Data Exchange (ETDEWEB)

    Rossander, Annelie; Andersson, Jonas; Axby, Fredrik; Schultz, Emma; Persson, Maarten; Svaerd, Sara [Carl Bro AB, Kristianstad (Sweden)

    2007-04-15

    The project can be regarded as a natural continuation to the Vaermeforsk project M4-324 by Axby and Hansson: 'Practical consequences of the Water Framework Directive implementation for combustion plants - New water cleaning technologies and methods for improvement of effluent discharges'. The six different combustion plants studied in this project have been chosen mainly on the basis of their varying size, fuel, cleaning equipment and recipient. The significance of water as a finite resource in the global ecosystems has been more pronounced recently. In the light of the growing stresses on the water resources the European Parliament accepted the Water Framework Directive in year 2000. The main purpose with the directive is to achieve and preserve a 'good water status', among other things through a long term protection of available water resources. Enclosure X of the Framework Directive contains a list of chemical substances where 33 'prioritized substances' and 'prioritized, dangerous substances' are specified. The objective of the list is to reduce the discharges of prioritized substances, and to fully eliminate the prioritized, dangerous substances both from industry and other contexts. Twelve of the substances mentioned on the prioritized list can or could be found in the water coming out from combustion plants. A predominant part of these substances are to be totally phased out in the foreseeable future according to the Water Directive. This can result in restrictions in the permissions to let out water from combustion plants to the surroundings. The substances concerned are the heavy metals lead, cadmium, mercury and nickel, both as pure substances and included in compounds, as well as a number of different polyaromatic hydrocarbons (PAH). The intent of the project has been to use an accepted computational model to create an analytic method (an ecotoxicological risk assessment), with the aim to meet the new requirements

  8. NDT methods for life-time assessment of high temperature plant; Ofoerstoerande provning foer livslaengdsbedoemning av hoegtemperaturanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Storesund, J [Swedish Inst. for Metals Research, Stockholm (Sweden)

    1996-10-01

    A comprehensive literature study of NDT and analysis methods for residual life-time assessment of high temperature plant has been made. The study has been concentrated on components in boilers, steam piping and turbines in fossil fired power plant. Most types of components are exposed to creep which is also the life-time limiting mechanism in many cases. In addition to creep, other stresses and damages which appear in plant are described for each type of component. Thermal fatigue, corrosion and embrittlement as well as combined damage mechanisms are also life-time limiting in many cases. The literature shows a large number of NDT methods developed and under development in purpose to identify and measure the size and extent of damage in the components. The methods and their limitations are described in relation to the experience and understanding of character, distribution and development of damage in different situations. 83 refs, 12 figs, 1 tab

  9. Gasification for fuel production in large and small scale polygeneration plants; Foergasning foer braensleproduktion i stor- och smaaskaliga energikombinat

    Energy Technology Data Exchange (ETDEWEB)

    Rodin, Jennie; Wennberg, Olle

    2010-09-15

    This report investigates the possibility of integrating biofuel production through gasification with an existing energy production system. Previous work within Vaermeforsk (report 904, 1012) has concluded that gasification for motor fuel production as a part of a polygeneration plant seems promising when looking at the energy efficiency. However, comparable data between different types of integration, energy plants and fuels was found to be needed in order to get a better understanding of how a gasifier would affect an energy system. The systems studied are the heat- and power production of a bigger city (Goeteborg) and a medium sized city (Eskilstuna), and a pulp mill (Soedra Cell Vaeroe). The latter already runs a commercial gasifier for burner gas production, where the gas is used in the lime kiln. The different types of polygeneration plants have been studied by setting up and evaluating mass- and energy balances for each system. The fuel products that are looked upon in this project are DME, methane, methanol and burner gas. The burner gas is used on site. The case studies have been evaluated based on energy efficiency for fuel production, electricity and district heating. The efficiency is foremost calculated for the higher heating value. In the case of the boiler integrated gasifier in Eskilstuna, the efficiencies have been calculated on the marginal fuel. We have also let the district heating remain unchanged

  10. Handbook for replacement of process control systems in thermal power plants; Handbok - Utbytesbehov i kontrollsystem foer vaermekraftverk

    Energy Technology Data Exchange (ETDEWEB)

    Tuszynski, J. [Sydkraft Konsult AB, Malmoe (Sweden); Eriksson, Tage [Vattenfall Energisystem AB, Stockholm (Sweden)

    1996-12-01

    Modernization of control equipment in more complex power plants, such as thermal power plants, requires special attention due to the almost complete change-over to new computerised technology. The introduction of new technology gives rise to great changes in both the process control systems and in operation and maintenance routines. The change-over to computerised technology also causes lack of spare parts and service for older equipment. The older technology becomes obsolete due to the great advantages that comes with new technology. Therefore, the lifetime of control equipment is not only coupled to traditional ageing and wear, such as oxidation and fatigue of material, but also to the fact that the old equipment is getting out of date. It becomes more and more common that this out-of-date factor, rather than ageing, sets the limit for the useful life of the equipment. The Handbook for replacement of process control systems in thermal power plants is thought to be a first help for engineers and managers who has the responsibility for process control modernization. The Handbook points out the factors that determines the service life of the control equipment. It also suggests what information is required in order to take a decision on modernization. The Handbook at its present form constitutes a first approach that leaves room for an extension later on. Any request to expand the Handbook should be put forward to Vaermeforsk or its partners

  11. Repository for spent nuclear fuel. Plant description layout D - Forsmark; Slutfoervarsanlaeggning foer anvaent kaernbraensle. Anlaeggningsbeskrivning layout D - Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    2010-07-15

    This document describes the final repository for spent nuclear fuel, SFK, which is located at Forsmark, in Oesthammar. The bedrock at the site is part of a so-called tectonic lens, in which the rock composition is relatively homogeneous and less deformed than outside the lens. The bedrock consists mainly of granite with high quartz content and good thermal conductivity. The central parts above ground are grouped in an operations area, located at the Soederviken on the south side of the intake duct for cooling water for nuclear power plant. Operating area is divided into an internal, secured portion, where the canisters of fuel are handled and there are links to the underground part, and a outer part, where the buffer, backfill and sealing used in the repository's barriers are produced. The above-ground part of the plant and also include storage of excavated rock, ventilation stations, and supplies of bentonite. The underground portion consists of a central area and a storage area. Caverns of the central area contain features for the underground operation. It communicates with the internal operating range above ground via a spiral ramp and several shafts. The ramp used to transport capsules of spent fuel and other heavy or bulky transport. The shafts are used to transport rock, buffer, backfill and staff, as well as for ventilation. The largest part of the space below ground is the repository where the canisters with the spent fuel are disposed. The capsules are deposited in vertical holes in the tunnels. When the deposit in a tunnel is complete, the tunnel is re-filled. The two main activities underground is rock work and disposal work, which are conducted separately from each other. Rock works covers all steps required to excavate tunnels and drill deposition holes, as well as to make temporary installations in the tunnels. To the landfill works count, besides the deposit of the capsule, the placement of the bentonite buffer in the deposition hole and

  12. Analysis of environmental risks with an encapsulation plant and a final disposal repository; Miljoeriskanalys foer inkapslingsanlaeggning och slutfoervar

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Johan; Herly, Lucien; Pettersson, Lars [SwedPower AB, Stockholm (Sweden)

    2006-05-15

    This report covers non-radiological environmental risks related to an encapsulation plant and a final repository for spent nuclear fuel. All stages of the above are covered. This means construction, operation, demolition and sealing. A risk, in this report, is defined as a combination of probability and consequence of an undesired event. An extensive and systematic effort has been made in order to identify all risks. If risks remain undetected it should be low probability events. The risks are also evaluated to see which risks are the more serious ones. A large part of the existing risks are oil or diesel on the ground. In general the main risks occur during the construction phase and they are similar to normal risks at every large construction project. Most of the above are discharges of oil products on the ground within the construction area. With a good organisation and a high environmental profile these discharges can be minimized and when needed cleaned. For some of the other risks the same is valid - with a good preventive work they can be reduced considerably. One event which has a relatively high probability for occurrence and which may not easily be cleaned is a damaged lorry leaking oil. The resulting damage depends on where it occurs and maybe also when. Neither in Forsmark nor in Oskarshamn there are common sources of water supply in direct connection to where lorries pass and the probability for a lorry accident to cause damage to the environment is limited. After the assessment and evaluation of risk reducing measures there is one risk that appears serious even though the probability is low. This risk is the possible influence of the final repository on the subsoil water. It is most important that a large effort is put on reducing this risk. The probability of traffic accidents with injuries or fatalities will increase slightly, especially during the second phase of the construction period, since the amount of traffic is expected to increase then. Of

  13. Simulation and cost analysis of systems for handling of fuel straw - applied to a heating plant in Skaane; Simulering och kostnadsanalys av hanteringssystem foer braenslehalm - tillaempning foer en vaermeanlaeggning i Skaane

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Daniel

    2010-05-15

    The following conclusions were drawn from this study: - The total costs for delivery of fuel straw to heating plants ranged from about 130 SEK/MWh to 180 SEK/MWh (1 SEK approx 0.14 USD), depending on the payment to farmers for the straw, the storage method used, the profit margins of the contractors, etc. - The area investigated, which covered parts of the municipalities of Svaloev, Esloev and Kaevlinge, has very good conditions for harvest of straw compared with other parts of Sweden. The yield of winter wheat (and straw) is high, the road network is well developed, the fields are concentrated and large, the straw crops ripen early, and security of supply between years is high. - For a harvest and handling system with an average capacity of about 8 000 tonnes of straw per year, the simulations showed that a machine system with six balers, two loaders in the field, four transporters (tractor), one loader at the stores and lorry transport to the heating plant was cost-effective with regard to system performance (for example, expressed as the average amount of straw baled per year with a moisture content below 18%, the average quantity of straw per year put into storage prior to 1 October, the average lying time for the straw between threshing and baling, etc.). - Harvesting straw from various crops (in this case winter rape, rye and winter wheat) instead of only winter wheat had no major impact on costs, but increased the chance to harvest 'greyer' straw with lower contents of alkali metals, chlorine, etc. Only including fields of at least 5 ha had a minor impact on costs. Noticeable cost savings occurred when the field size limit was set to 10 ha or more. Increasing the moisture content limit at baling to 20% made it possible to harvest more straw, especially in years with difficult weather conditions. - The storage method used had a decisive impact on costs. Outdoor storage decreased the total costs to 133 SEK/MWh (7% storage losses), compared with 154

  14. Guidance for classification of residues from combustion and incineration in accordance with the Swedish ordinance for waste; Vaegledning foer klassificering av foerbraenningsrester enligt Avfallsfoerordningen

    Energy Technology Data Exchange (ETDEWEB)

    Adler, Peter [AaF Energi och Miljoe AB, Stockholm (Sweden); Haglund, Jan-Erik [Soederenergi AB, Stockholm (Sweden); Sjoeblom, Rolf [Tekedo AB, Nykoeping (Sweden)

    2004-05-01

    A new ordinance for waste came into force in Sweden on the first of January 2002, replacing some previous ordinances. The new ordinance is based on certain EU directives and contains amongst other things new rules regarding how certain streams of waste are to be classified into hazardous waste and non-hazardous waste. In a number of cases, the classification is to be made according to whether or not the waste possesses one or more of a number o properties H1 - H14, i e if the waste contains hazardous substances. The new rules are based on the regulation that exists for chemical substances and preparations. When attempts have been made to use these new rules in practice - e g for residues from incineration and combustion - it has become apparent that they are very difficult or even impossible to apply. The primary reason for this is that the residues contain a very large number (thousands) of substances which would have to be analysed and for which the hazard would have to be assessed correctly in accordance with the criteria for the properties (H4 - H8 and H10 - H11). Furthermore, some of the properties listed in the ordinance for waste lack criteria for assessment of hazard. These are H13 (can give rise to another substance which may be hazardous, e g leachate) and H14 (hazardous to the environment). Moreover, there are significant differences between the Ordinance of waste and the regulation of the National Chemicals Inspectorate. It is on the latter that the rules in the Ordinance of waste are based, and this is also the cause of many of the questions and of the uncertainties in the classification. In the present report, a method is developed and described for classification of residues from combustion and incineration. The method is to be applicable in practice without compromising environmental and health aspects. As a part of the present work, a compilation of content and alteration of chemical substances in is carried out. In another chapter, the experience from implementation of European Union directives in other countries is described. The proposed simplified method proposed in Chapter 7 implies the following: Reference substances are selected for different inorganic and organic chemical substances in the residues. These reference substances are utilised as a basis for the classification against the properties H4 - H8 and H10 - H11. This leads to a very substantially reduced need for analyses. The reference substances have been chosen in a conservative way so that the hazard for health and environment will not be underestimated. The main principles of the regulation on chemical products are applied, e g regarding weighting of the properties. The property H13 is assessed based on the properties H4 - H8 and H10 - H11. The property H14 is assessed based on the rules for environmental hazard in the regulations of the National Chemicals Inspectorate. In practice the simplified methodology in a normal practical case amounts to an assessment with respect to 15 metallic elements and four groups of organic substances. The degree of hazardousness is then figured based on certain schedules together with levels provided in available chemical data bases. One prerequisite for the application of the simplified methodology is that the residues at some point are contacted with water. In the end of the report (Chapter 8), the procedure for classification according to the simplified method is described and an example is given of a classification on a specific residue from combustion.

  15. Guidelines for calculating impacts on the Swedish environmental objectives from altered energy use; Vaegledning foer att beraekna paaverkan fraan foeraendrad energianvaendning paa de svenska miljoemaalen

    Energy Technology Data Exchange (ETDEWEB)

    Engstroem, Rebecka; Gode, Jenny; Axelsson, Ulrik

    2009-01-15

    The guidelines in this report have been developed by IVL Swedish Environmental Research Institute, within a project financed by the Environmental Objectives Council, the Swedish Energy Agency and the Swedish Environmental Protection Agency. The idea originated from an earlier project for the Swedish Energy Agency and the Swedish Environmental Protection Agency, where the potential of a business model for energy efficiency (Energy Performance Contracting, EPC) to contribute to fulfil the national environmental objectives was studied. When environmental impacts from the studied EPC projects was to be calculated, it was evident how many difficult methodological choices one is faced with when trying to follow up the environmental impacts from projects changing the energy use. A second project was then performed to further analyse the issues involved. The result is this guideline report. The guidelines are on the first hand directed at companies and municipalities performing projects with effects on the energy use, that want to calculate impacts from these on the Swedish environmental objectives. The guidelines can also be useful for county administrations, central authorities and other actors with interest in the issues. A starting point for the recommendations is the Swedish environmental objectives, with focus on those of special interest in relation to energy use and airborne emissions. These are Reduced climate impact, Clean air, Natural acidification only, Zero eutrophication and A good built environment. The environmental objectives are mainly concentrated on what affects the Swedish environment. However, not only emissions in Sweden cause such effects, but also emissions in other countries can be transported by air and fall down and cause impacts in Sweden. Thus, the guidelines focus on Sweden, but include to a certain extent also emissions in other countries. Another starting point is that the guidelines are developed to follow up effects from individual projects or measures. This differs in fundamental aspects from follow up of effects within a geographic unit (for example a municipality) or of environmental impacts from an organisation on a yearly basis. When following up environmental impacts from something other than a project perspective, the recommendations given are not doubtlessly applicable, since what are the most correct methodological choices differ depending on the starting point. The report is called guidelines, and not handbook or manual. This is because of the fact that there are many aspects to consider in the topical methodological choices, and the recommendations are to be considered as approximations. The aim of the report is therefore also to function as a knowledge survey in the area of environmental assessment of energy use, with in-depth background information of the recommendations and references to supplementary literature. The guidelines cover stationary energy use (hence, transport is not covered), with primary energy and life cycle perspectives to embrace total environmental impacts and facilitate comparisons between energy carriers. However, comparisons should always be made with caution, since there are several aspects to consider in conversions between energy carriers. Such aspects are how impacts are transferred between local, national and international levels, between Sweden and other countries, or between different environmental objectives. Weighting between such aspects are very difficult, and measures that reduce impacts in general are therefore preferable, when this is possible

  16. Environmental evaluation of electric power from a systems perspective. Guidance for sustainable development; Miljoevaerdering av el ur systemperspektiv. En vaegledning foer haallbar utveckling

    Energy Technology Data Exchange (ETDEWEB)

    Gode, Jenny; Byman, Karin; Persson, Agneta; Trygg, Louise

    2009-12-15

    The electricity market is deregulated. This means that all electricity customers are free to choose their electricity supplier. Many utilities market renewable electricity products such as wind power or hydroelectric power, saying that the customer makes a contribution to the environment by choosing these products. But is that really true? In this report, four researchers and consultants give an account of their views on how environmental valuation of electricity should be made. Specifically they discusses the driving forces for the development of the electricity system and the purchase of environmentally certified electricity and the link to environmental benefits. An important objective is to provide guidance as to how individuals and businesses through their actions can contribute to sustainable development

  17. Pre-study - mobile briquetting plant for reed canary grass in inland Northern Sweden; Foerstudie - mobil briketteringsanlaeggning foer roerflen i norrlands inland

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne; Lundmark, Bo

    2009-07-01

    The aim of this preliminary study was to summarize existing information and to develop an outline plan for a mobile briquette plant based on the conditions and requirements of reed canary grass production on forestry land. The results of the study show that there is potential to build up small-scale briquette production from reed canary grass in the areas around Arvidsjaur, Lycksele and Malaa. Important conclusions from the study are that there are potential users for reed canary grass briquettes in all three areas studied, but that profitability for mobile briquette plants is dependent on the willingness of the users to pay well for the briquettes. These briquette plants would need a relatively high degree of automation for commercial operation to be profitable. The first plant should therefore be collocated with another business so that staff, machinery (e.g. loader) and storage space can be shared with other operations. One appropriate location would be to build up activities for a mobile reed canary grass briquette plant around Glommers Miljoeenergi's pellet plant in Glommerstraesk. Thus, the plant could be used as a demonstration mobile unit, with a stationary 'home production base'CO{sub 2} Glommerstraesk

  18. Better and more efficient collaboration for increased use of field fuel in heating plants; Baettre och effektivare samverkan foer oekad anvaendning av aakerbraenslen i vaermeverken

    Energy Technology Data Exchange (ETDEWEB)

    Arkeloev, Olof (Agrovaest, Skara (Sweden)); Hellstroem, Chris; Hollsten, Ronnie (KanEnergi Sweden AB, Skara (Sweden)); Lindh, Carina (LRF Konsult, Skara (Sweden))

    2010-05-15

    Despite that the potential for field fuels in SW Sweden is great and that the combustion characteristics of fuels are known, the interest for field fuels has been low from farmers and heating plants. The purpose of the project is to identify why the introduction of field fuel into heating plants is going so slow and to suggest possible solutions. Field fuel is missing the general structure and tradition that is found in forest fuels in terms of harvesting, processing, logistics and business models. The overall long-term objective is a better and more effective cooperation between heating plants, farmers and logistic companies for the increased use of field fuels in heating plants. The potential for field fuel in the area is great but won't be sufficient to cover the need. The raw materials that exist today and are deemed will be relevant in the future are willow, straw and grain kernel. We have divided the heating plants into two groups; Small plants with a furnace less than 35 MW, and large plants with an effect over 35 MW. Common to both small and large heating plants is that there must be a willingness to receive and combust field fuels for the share of field fuels to increase. For the small heating plants to be able to receive and combust field fuels the knowledge of the combustion properties of these fuels must increase. Larger heating plants have better opportunities to use field fuels in their boilers when it comes to the technology and the know how. They have a more controlled handling and receiving of fuels. It is not uncommon that storing and blending of fuels will take place at their own facility. They also have more experience of handling a larger number of suppliers at the same time. The heating plants would like to see standardization in terms of fuel characteristics, and they prefer to obtain approximately the same burning performance regardless of delivery date. Today, the small heating plants do not have the routines to manage multiple small

  19. Ice Forces on Offshore Wind Power Plants. Descriptions of mechanisms and recommendations for dimensioning; Islaster paa vindkraftverk till havs. Beskrivning av mekanismer och rekommendationer foer dimensionering

    Energy Technology Data Exchange (ETDEWEB)

    Bergdahl, Lars [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept of Water Environment Transport

    2002-02-01

    Mechanisms for ice-loads on off-shore wind power plants are described, The ice-loads are due to thermal expansion, water level variations, drifting ice and ice-reefing. Ice accretion is briefly treated. Ice instance, ice thickness, ice retention time, water level variations and stream velocities in Swedish waters are compiled. The main text deals with recommendations for dimensioning wind power plants at sea. In the appendices, a thorough review of the physical and mechanical properties of ice is presented.

  20. Model based monitoring functions for safer and more efficient operation of remotely operated plants; Modellbaserade oevervakningsfunktioner foer saekrare och effektivare drift av fjaerrstyrda anlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Bjoerklund, Thomas; Raaberg, Martin [Carl Bro Energikonsult AB, Malmoe (Sweden)

    2004-12-01

    The increasing demands on profitability lead to an increase in the demands on production units. These demands include an increase in production capacity, in efficiency and a decrease in production costs. To accommodate these demands the tendency is to connect several production units to control and monitor them in one central control room. This generates a huge demand on the operators. They should understand a large amount of different plants. They should understand how the plants act in several operation points and in addition understand how they operate together. This results in the fact that the monitoring and maintenance personnel are not able to have full knowledge about the processes in all these plants. The implementation of a simple device oriented, model based monitoring function will help the personnel in the decision making in process related issues. This report describes methods to easily include process knowledge in the I-C-system. Emanating from known physical facts about the functionality of the devices and use them to combine process values into functions that will describe the status of the device alarms can be created. These alarms are activated if the functionality deviates from the normal operating procedure in specific ways. The primary target group is the plant owners of district heating plants, but the process industry in general is faced with the same problems. The work includes three parts; an investigative part, a compiling part and a describing part. The investigative part involves investigating theories, the normal level of instrumentation and discussions with operators to confirm the alarms and the appropriate actions. The compiling part involves to in the best way mace use of the normal level of instrumentation to achieve the operator's goals with respect to valid alarms. These goals are attained through adapting the existing theory in the area. The describing part includes the presentation of the equations and relations involved

  1. Evaluation of regulations and norms for concrete constructions in Swedish nuclear power plants; Utvaerdering av regler och normer foer betongkonstruktioner i svenska kaernkraftsanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Jovall, Ola (Scanscot Technology AB, Lund (Sweden))

    2010-12-15

    In the SSM's regulations and recommendations, there are at present no specific requirements and adequate guidance on how concrete structures should be designed in case of new buildings or verification analyses of existing buildings. The result of the work presented in this report constitute the basis for SSM's ongoing regulatory project Investigation regarding requirements for construction, design, analysis and review of reactor containments and other safety-related building structures. The project includes the following: 1. Summary of the regulations and requirements that have been applied at the initial design and new construction of concrete structures at the Swedish nuclear power plants. 2. Comparison and evaluation of relevant regulations published by the European and North American authorities. 3. Comparison and evaluation of relevant codes, standards, guidelines etc. for load-bearing concrete structures in different countries. 4. Conclusions and recommendations to the regulatory framework for the design of load-bearing concrete structures at the Swedish nuclear power plants. Based on a comparison and evaluation of regulations from the U.S., Canada, France, the UK, Finland and Sweden, as well as guidelines established by the international organizations IAEA and EUR, the following general recommendations are provided as a regulatory framework for the design of load-bearing concrete structures at the Swedish nuclear power plants: 1. The Eurocodes will replace the BKR design rules of Swedish National Board of Housing, Building and Planning as the conventional building regulations on the construction of nuclear power plants. 2. A general review and updating of the existing industry standard Design rules for buildings at nuclear facilities DRB:2001 is implemented. Reference is made to the Eurocodes with regard to conditions of conventional design rules

  2. Status for cast stainless steel in older Swedish nuclear power plants, March 1996; Status foer gjutet rostfritt staal i aeldre svenska kaernkraftverk, mars 1996

    Energy Technology Data Exchange (ETDEWEB)

    Trolle, M.

    1996-04-01

    The purpose of this study is to compile what is known about larger cast components primarly in older BWR nuclear power plants with external circulation pumps. The work includes metallurgical data and a compilation on the material that the owner of Oskarshamn 1, OKG AB, has delivered to The Swedish Nuclear Power Inspectorate as a result of the investigation of these components. An overview of the investigations performed on the other Swedish plants of similar design during the annual outage 1995 is also described in this report. International experinece is also reported. The results from OKG AB show that there has been extensive cracking in both valves and pump casings and that they are probably resulting defects from the manufacturing process, but an environmental factor cannot be excluded. In order to get a complete picture of the situation in Swedish nuclear power plants a more extensive survey needs to be performed. Internationally the phenomenon of hot cracking in cast stainless steel is well known, but not as severe as in Oskarshamn 1. One question however that is discussed is the recommended amount of ferrite in these steels in order to avoid hot cracking without risking embrittlement of the ferrite phase. The Swedish utilities specify 3%, some European countries recommend 8%. Japan suggests ferrite contents up to 30%. 25 refs.

  3. Evaluation and development of methods for determining methane emissions from biogas plants - Literature Study; Vaerdering och utveckling av maetmetoder foer bestaemning av metanemissioner fraan biogasanlaeggningar - Litteraturstudie

    Energy Technology Data Exchange (ETDEWEB)

    Holmgren, Magnus Andreas (SP, Boraas (Sweden)); Willen, Agnes; Rodhe, Lena (JTI, Uppsala (Sweden))

    2011-11-15

    Previous work in areas such as framework of voluntary commitment shows that there is a need for techniques for measurement of methane and other greenhouse gases from various sources in the handling of organic residuals. There are no established methods for determining for instance emissions of methane from open or partially open tanks and cisterns, typically residue storage and the like. This report gives results from Phase 1 of this project, in which literary studies, market research studies, interviews and site visits have been made to identify a number of methods applied for the determination of emissions from open areas, such as liquid surfaces, but also land. Focus is on methods that can be applied to plants for biological treatment, which also includes the water treatment process at the treatment plants, but also the procedures used in measurements on land, landfills and processing plants are studied. First, the report gives a brief overview of a large number of measurement methods, where more detailed descriptions of four methods are given. The four methods are considered to be the most promising to pursue in the following phases of the project: - chamber technology; - sampling hood; - plume measurement with DIAL (Differential Absorption Lidar); - air input in a covered storage.

  4. Energy savings in dust collector plants of bag house filter type. Phase 1 - Literature study; Energieffektivisering av anlaeggningar foer stoftrening med slangfilter. Etapp 1-Litteraturstudie

    Energy Technology Data Exchange (ETDEWEB)

    Eriksson, Lars; Wikman, Karin; Berg, Magnus [AaF-Energi and Miljoe AB, Stockholm (Sweden)

    2004-01-01

    The largest energy demands in connection with the operation of bag house filters are the electric energy consumption for the fans, securing the flow of flue gas through the filter, and the electric energy consumption when producing the pressurized air (compressors or high pressure fans). Considering the significantly increased fan work when having a non-optimised cleaning of the filters, it seems justified to investigate the possibilities to minimise the unnecessary pressure drop. There is also a saving potential in the filter cleaning process, which otherwise may cost an unacceptable amount of pressurized air or other energy. The main purpose of this work is to develop methods to optimize the operation of bag house filters, which is started up with this report containing a follow-up of what has been done in Denmark and a confirmation of the technology status. In the next step, a case study where two-three plants are examined more in detail is suggested followed by a potential study to estimate the total energy saving potential in Sweden. Dust precipitation with bag house filters is basically a rather simple technique, which has existed in flue gas cleaning for about 50 years. From the literature study it can be established that there has been no revolutionary development in the field, but there are some work being done mainly to introduce new filter material but also to optimise the use of bag house filters with new computer based control systems. The largest potential of energy saving prevails if the filter from the beginning is overloaded, which usually is the case. The reason for overload may be a too large volume flow in relation to the filter area, that the dust has penetrated and blocked the filter, a defective filter cleaning process or that wrong filter material has been chosen. In Denmark a study has been made with the purpose to investigate the possibilities to optimise the energy consumption for bag house filters. For the three plants studied, an

  5. Biological recipient control at the Ringhals nuclear power plant. Annual report for 2011; Biologisk recipientkontroll vid Ringhals kaernkraftverk. Aarsrapport foer 2011

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, Maria; Gustavsson, Frida; Fagerholm, Bjoern

    2012-07-01

    The cooling system of the Ringhals nuclear power plant affects the fish community in two steps. In the first step, seawater is used to cool the system in the nuclear power plant. Fish eggs, larvae and small juveniles are carried by the incoming water and are exposed to risk of damage or mortality. In the second step the heated water is released back into the sea, where the fish is affected by the increase in temperature. Reactor 1 and reactor 3 at Ringhals nuclear power plant produced electricity during the major part of the year 2011, with exceptions for the annual audits, and shorter stops in production. Reactor 2 only operated between January and April, due to a fire which led to a shutdown and a thorough remediation work during the rest of the year. Reactor 4 was producing electricity from January to June, but was later shutdown due to a prolonged annual audit until November. Fish eggs and fish larvae are sampled in the incoming cooling water using a modified Bongo net to monitor losses of eggs and larvae in the nuclear power plant. The abundance of shorthorn sculpin larvae (Myoxocephalus scorpius) has decreased since the sampling period started, although it is still the most abundant larvae. Also the abundance of rock gunnel larvae (Pholis gunnellus) has decreased over the years. To sample juvenile fish a modified Isaacs-Kidd midwater-trawl is used. This sampling is mainly focused on glass eels (Anguilla anguilla). The abundance of glass eels have declined strongly since the beginning of the 1980's, but a minor increase was observed in 2011. The decline of the glass eel abundance is most probably due to a general decrease in recruitment and not to a local effect caused by the nuclear power plant. The effects of the heated water released into the sea are monitored by fykenet surveys in the recipient as well as in a reference area. These two areas are monitored in two seasons to compare differences between the two areas in naturally cold and warm water of

  6. Biological recipient control at the Oskarshamn nuclear power plant. Annual report for 2011; Biologisk recipientkontroll vid Oskarshamns kaernkraftverk. Aarsrapport foer 2011

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Jan; Franzen, Fredrik; Lingman, Anna

    2012-07-01

    Potential ecosystem effects caused by the effluent cooling water from the Simpevarp nuclear power plant, close to Oskarshamn on the Swedish coast of the Baltic Proper, are monitored in yearly surveys using gillnets and fyke nets. Fishing is undertaken at several sites in a coastal gradient starting at the location of the emitted cooling water, and in a reference area 100 km north of the recipient. Soft bottom macro fauna and macro vegetation are monitored both in the gradient and in the reference area. Fish mortality due to entrapment in the cooling water system and commercial landings are monitored to assess the effects on the local fishery. The water used for cooling is normally heated by 10-12 deg C when passing through the power plant. In sheltered parts of the recipient bay of Hamnefjaerden, the surface water was 4-6 deg C warmer in April-November 2011 than in the reference area comparable reference areas and the emitted water occasionally exceeded 30 deg C in the summer. Fish losses in the cooling water rinsing system were dominated by Baltic herring. Effects on abundances at the population level are estimated to be small, but local effects cannot be ruled out. Perch (Perca fluviatilis), roach (Rutilus rutilus) and silver bream (Blicca bjoerkna) dominated the catches in the surveys with gillnets in Hamnefjaerden, as well as in the archipelago surrounding the power plant. Perch abundances increased in these areas. Catches of roach decreased close to the power plant, but also in the reference area. Perch in the gillnet catches were younger and grew faster close to the power plant than in the reference area. Abnormal gonads, previously observed at high frequencies in perch and roach in Hamnefjaerden, were rare in the 2011 sampling. The abundance of young of the year perch in the recipient did not change over time. The size of the perch fry however, increased in Hamnefjaerden, as well as in the local reference area. The catch and size structure of yellow eel

  7. Digestion with initial thermophilic hydrolysis step for sanitation and enhanced methane extraction in wastewater treatment plants; Roetning med inledande termofilt hydrolyssteg foer hygienisering och utoekad metanutvinning paa avloppsreningsverk

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Emelie; Ossiansson, Elin [BioMil AB, Lund (Sweden); Carlsson, My; Uldal, Martina; Johannesson, Sofia [AnoxKaldnes AB, Lund (Sweden)

    2012-02-15

    Thermophilic (55 deg) pre-hydrolysis has been shown to improve methane yield, organics reduction and/or treatment capacity when applied to anaerobic digestion (Persson m. fl. 2010). The method has also proven to kill off pathogens, making it an interesting hygienisation alternative to pasteurisation. The Swedish Environmental Protection Agency has opened up for the possibility to validate new methods for hygienisation, if the pathogen reduction can be proven to be efficient enough. Thermophilic pre-hydrolysis has several possible advantages to pasteurization; e. g. district heating of lower temperature can be used, the stability of the process may increase, as well as the efficiency and extent of the digestion process. The objective of this study is to evaluate the effect of thermophilic pre-hydrolysis on anaerobic digestion (AD) of sewage sludge with respect to: 1. Biogas/methane production and solids reduction. 2. Correlations between substrate properties, process conditions and effect on the AD process. 3. Pathogen reduction efficiency. 4. Operational consequences. Laboratory trials in continuous and batch mode were conducted on sewage sludge from four Swedish wastewater treatment plants. In the trials thermophilic pre-hydrolysis with consecutive mesophilic AD was compared to conventional one-step mesophilic AD, as well as pre-pasteurisation with consecutive AD. For all the tested sludge samples the reduction of TS and VS increased as a result of thermophilic pre-hydrolysis prior to mesophilic AD. The results with respect to methane yield were not as straightforward. Increased production of biogas was achieved in pilot scale, but the methane production did not improve. In the laboratory trials the effect on methane production varied from -8 % till +18 % for the sludge samples tested. The most positive results were achieved in the test that had the highest organic load and that was fed with a sludge that was low in fat and high in carbohydrates, compared to the

  8. Modelling of a hybrid plant and development of a control system for the Vaesthamn plant based on artificial neural networks; Modellering av hybridanlaeggning samt utveckling av oevervakningssystem foer Vaesthamnsverket baserat paa Artificiella Neurala Naetverk

    Energy Technology Data Exchange (ETDEWEB)

    Assadi, Mohsen; Fast, Magnus [Lund Inst. of Technology (Sweden). Dept. of Energy Sciences

    2006-12-15

    The project aim is to model the hybrid plant at Vaesthamnsverket in Helsingborg using artificial neural networks (ANN). The definition of a hybrid plant is that it uses more than one fuel, in this case a natural gas fuelled gas turbine with heat recovery steam generator (HRSG) and a biomass fuelled steam boiler with steam turbine. The models in the present project are based on operational data from the plant in contrary to previous projects where synthetic (simulated) data has been used in a large extent. The gas turbine represents the subsystem that has received most attention in previous projects, which will also be the case for the present project although models of the HRSG, steam boiler and steam turbine are created since the whole plant is of interest. The completed ANN sub modules are connected in a network, which can be used for e.g. offline simulation and real-time condition monitoring of the plant. A product, including all sub modules, is created in shape of a user-friendly interface in an MS Excel environment. This user interface can be used for continuous monitoring, training personnel and in planning of the operation. The target group is the plant owners and the original equipment manufacturers (OEM). The plant owners interest lies in receiving a product that can assist them when operating the plant, for instance supply them with information about the grade of degradation. The OEMs main interest lies in investigating the possibilities of delivering ANNs, based on synthetic data, along with their new gas turbines. Vaesthamnsverket have contributed with operational data from the plant as well as support in plant related questions. Siemens have contributed with expert knowledge about their gas turbine, the SGT800. The received data has been examined and filtered before used for training ANN models. The models have been evaluated with independent data. The results are very promising with ANN models showing high prediction accuracy. All subsystems can be

  9. Prestudy: Anaerobic digestion with primary hydrolysis from increased methane production in waste water treatment plants band biogas plants; Foerstudie: Roetning med inledande hydrolyssteg foer utoekad metanutvinning paa avloppsreningsverk och biogasanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Emelie; Ossiansson, Elin (BioMil AB, Lund (Sweden)); Carlsson, My; Uldal, Martina; Olsson, Lars-Erik (AnoxKaldnes AB, Lund (Sweden))

    2010-04-15

    Anaerobic degradation of organic matter is a multi-step process through the action of various groups of microorganisms whose optimum conditions can differ considerably regarding e.g. nutrient and pH demand, sensitivity for changes and patterns for growth and nutrient uptake. One way of optimizing the anaerobic digestion process, and thereby increase the biogas production and the reduction of organic matter, can be to physically divide the anaerobic digestion process in two steps consisting of an initial hydrolysis and acid production step followed by a methane production step in an anaerobic digester. One problem with the biogas processes of today is that not all organic matter that is added to the process becomes available for conversion into biogas. This is particularly evident in digestion of waste water treatment sludge where almost half of the organic matter added remains after anaerobic digestion. More efficient utilization of substrate in biogas plants is an important element to increase the profitability of biogas production. The possibility to use different pre-treatment methods is being discussed to increase the degree of conversion of organic matter into biogas in the digester. Pre-treatment methods are often energy as well as cost demanding and can require the addition of chemicals. To use the microbiological steps in the biogas process more efficiently by adding an initial hydrolysis step is a method that does not require the usage of chemicals or increased energy consumption. This pre-study is based on literature studies related to anaerobic digestion with initial biological hydrolysis and collected knowledge from full-scale plants, universities and suppliers of equipment. Nearly 70 published scientific articles relevant to the subject have been found in the performed literature searches. The articles have been subdivided according to the purpose of each article. A large part of the articles have concerned modelling of anaerobic digestion why a

  10. Alternatives to Conventional Construction Materials on Landfills. A Guide; Alternativa konstruktionsmaterial paa deponier. Vaegledning

    Energy Technology Data Exchange (ETDEWEB)

    Rihm, Thomas; Rogbeck, Yvonne; Svedberg, Bo; Eriksson, Maria

    2009-03-15

    Before a landfill can be sited, an application for a permit from the authorities is required. Already in the application process the consequences concerning impact on human health and on the environment must be described, including descriptions of e.g. bottom liners and capping constructions. Since there is a long period of time between when the permit is given and when the capping will be carried out, it is common practice, either to postpone decisions concerning capping details, or to delegate the decisions to the supervisory authorities to be made at a later stage. All constructions must however be approved by the authorities before they can be carried out. A construction must fulfil the demands for its function. For the capping this means that the percolation through it must be low, even in a long time perspective. A construction may not in itself cause adverse environmental effects, e.g. leaching of hazardous substances from the construction material. Thus, there are functional as well as environmental demands. Beside the functional demands given in the Swedish legislation, notably in the ordinance on landfilling, the construction must be physically stable, also in a long time perspective. The materials in the construction must have sufficient strength, and may not change over time, e.g. due to degradation, which could lead to malfunction. Demands on environmental behaviour can be divided into two parts. Humans and animals must be kept from direct contact with dangerous substances including dermal contact, inhalation of dust or gases and oral intake of soil, plants or berries. Secondly, dangerous substances may not be spread with surface or ground water to an extent that could lead to adverse effects on human health or on the environment. The impact on the environment is not only depending of the materials being used, but also on the construction design, where in the landfill the construction is situated and, not least, how the landfill is located. It is

  11. Guidance to the regulations on sustainability criteria for biofuels and bioliquids Version 3.0; Vaegledning till regelverket om haallbarhetskriterier foer biodrivmedel och flytande biobraenslen Version 3.0

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Swedish Energy Agency is the regulatory authority for enforcement of the Act (2010:598) concerning sustainability criteria for biofuels and bioliquids. The Act implements into Swedish law provisions on sustainability criteria in the so-called renewable-directive. Authority is based on the authorization issued regulations, but there are many details that are not regulated by statute. Many of the interested companies contacts the authority and want to know more about what will apply in various respects. The Agency has therefore chosen, in this guide, to introduce more detailed explanations of the rules that exist in law and regulation. It is thus not a question of legally binding rules. This third version of the guidance has been supplemented with sections on reporting. The Agency will gradually expand the guide to include more parts of the acquis. The guidance has been produced by the unit for sustainable fuels. Before the content was fixed definitively the guidance has been circulated to NGOs and government.

  12. Guidance to the regulations on sustainability criteria for biofuels and liquid biofuels. Version 2.0; Vaegledning till regelverket om haallbarhetskriterier foer biodrivmedel och flytande biobraenslen. Version 2.0

    Energy Technology Data Exchange (ETDEWEB)

    Engstroem, Lina; Jozsa, Emmi; Hagberg, Linus; Wollin, Per; Petren Axner, Margareta

    2012-11-01

    For biofuels and liquid biofuels: Swedish Energy Agency's guidance on the regulatory framework on sustainability criteria have been updated and expanded with new sections on control systems, independent auditing, sustainability statements and verification of land criteria in Sweden.

  13. Power plants structures offshore - a method for locally increasing the biologic diversity in the Baltic Sea?; Kraftverkskonstruktioner i havet - en metod foer att lokalt oeka den biologiska maangfalden i Oestersjoen?

    Energy Technology Data Exchange (ETDEWEB)

    Malm, Torleif

    2005-02-01

    Preliminary research results from Kalmar Sound (Baltic Sea) reviewed in this report indicate the the submarine constructions of an offshore wind power plant can have positive effects on stationary fish as well as benthic animals and algae. This happens even though the total surface of the wind power plants is but a minor part of the surface of the wind power park. It is reef effect, bringing in foreign substrates and structures in the marine environment that causes this effect.

  14. Materials for higher steam temperatures (up to 600 deg C) in biomass and waste fired plant. A review of present knowledge; Material foer hoegre aangtemperaturer (upp till 600 grader C) i bio- och avfallseldade anlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Staalenheim, Annika; Henderson, Pamela

    2011-02-15

    A goal for the Swedish power industry is to build a demonstration biomass-fired plant with 600 deg C steam data in 2015. Vaermeforsk also has a goal to identify materials that can be used in such a plant. This project involves a survey of present knowledge and published articles concerning materials that are suitable for use in biomass and wastefired plants with steam data up to 600 deg C. The information has been gathered from plants presently in operation, and from field tests previously performed with probes. Plants firing only household waste are excluded. The components considered are waterwalls/furnace walls (affected because of higher steam pressures) and superheaters. Fireside corrosion and steam-side oxidation are dealt with. Candidate materials (or coatings) are suggested and areas for further research have been identified. The purpose of this project is to give state-of-the-art information on what materials could be used in biomass and waste-fired plant to reach a maximum steam temperature of 600 deg C. This report is aimed at suppliers of boilers and materials, energy utility companies and others involved in building new plant with higher steam data. In accordance with the goals of this project: - Materials suitable for use at higher steam temperatures (up to 600 deg C steam) in wood-based biomass and waste-fired plant have been identified. Austenitic stainless steels HR3C, TP 347 HFG and AC66 all have adequate strength, steam-side oxidation and fireside corrosion resistance for use as superheaters. AC66 and HR3C have better steam-side oxidation resistance than TP 347 HFG , but TP 347 HFG has better fireside corrosion resistance. It is recommended that TP 347 HFG be shot-peened on the inside to improve the oxidation resistance if in service with steam temperatures above 580 deg C. - Furnace walls coated with Ni-based alloys or a mixture of Ni- alloy and ceramic show good corrosion resistance at lower temperatures and should be evaluated at higher

  15. Devices for separation of particle emissions from biofuel plants smaller than 10 MW - Today's technology and potential for development; Stoftreningsteknik foer biobraensleanlaeggningar mindre aen 10 MW - tekniklaege och utvecklingspotential

    Energy Technology Data Exchange (ETDEWEB)

    Roennbaeck, Marie; Gustavsson, Lennart; Martinsson, Lars; Tullin, Claes; Johansson, Linda

    2002-09-01

    The objective of this report is to compile a survey of available technologies for separation of particles and to present research and development in the area of particle separation for biofuel plants smaller than 10 MW. Technical and economical opportunities to transfer the technologies used today in larger plants to smaller ones are discussed. As the health effects of aerosols are under investigation, the issue of separation of particle less than 1 {mu}m is especially scrutinised. Current research concerning the particle size distribution at different load is presented. The project has been realised partly as a literature survey, partly through contacts with scientists in the area and manufacturers of devices for flue gas cleaning and particle separation. The target group is owners of plants, manufacturers of devices and authorities with responsibility for air quality and energy planning. Fabric filters is an established technology that can perform low particle emissions (less than a few mg/m{sup 3}) at a low cost also at smaller plants. Also electrostatic precipitators can perform the same low emissions, but the cost for installation at smaller plants has to be reduced. Both these technologies can, properly designed, separate submicron particles. Cyclones can today as its best perform a little less than 100 mg/m{sup 3} at 13 % CO{sub 2}. Cyclones are used together with other technologies to achieve high separation at a low cost. Cyclones are attractive because of their simplicity and low price, but because they use inertia forces as separation mechanism, they can never separate submicron particles. Conventional scrubbers and flue gas condensers are capable of separation of submicron particles but the efficiency is lower compared with fabric filters and electrostatic precipitators. The emission level after a scrubber/flue gas condenser is about 70 - 80 mg/m{sup 3} at 13 % CO{sub 2}. New technologies for separation of particles oriented towards smaller plants and

  16. Practical consequences of the Water Framework Directive implementation for combustion plants. New water cleaning technologies and methods for improvement of effluent discharges; Praktiska konsekvenser foer foerbraenningsanlaeggningar vid infoerandet av Vattendirektivet. Nya reningstekniker och foerbaettringsaatgaerder vid utslaepp till vatten

    Energy Technology Data Exchange (ETDEWEB)

    Axby, Fredrik; Hansson, Christina [Carl Bro Energikonsult AB, Malmoe (Sweden)

    2004-11-01

    As a consequence of the growing impact on water resources the Water Framework Directive was legislated in 2000. The directive should ensure that a 'good water status' and entail a coordinated legislation striving for a long-term protection of all water resources. Stakeholders should be able to participate in the preparations of river basin management plans and programs of measures. District based water authorities will administrate the implementation and are mandated to decide upon regional environmental quality standards and promulgate fees for water use and discharges. The Directive contains a list of 33 prioritized substances that should be reduced or phased out. Discharges from combustion plants contain twelve, polyaromatic hydrocarbons (PAH) and heavy metals. PAH and heavy metals impacts growth and vital functions as respiration and photosynthesis of water living organisms and induces cancer in humans. NOEC-values (NO Effect Concentration) state manageable substance concentrations for an organism. Flue gas condensate contains concentrations of some of the substances which impact exceeds the critical state level. Extended sewage treatment could thus be needed. Sludge, wash and soot water contains elevated levels of heavy metals. This water is normally treated by municipal sewage treatment. Further treatment at plant site could be relevant. Presence of PAH and heavy metals in leach water depends on the precipitation. Additional flowing-independent water treatment could be relevant. It is very uncertain how plant owners will be affected. Licenses could be reviewed and standards could be raised for sensitive recipients; new limits for prioritized substances and standards for other types of discharges and water fees could be added. Respites could be given if costs exceed the benefits. Location, ecotoxicological risk assessments and precautionary measures could become more relevant in an EIA. Pricing of water could take place by using a system of emissions

  17. Digestion with initial biological hydrolysis step for enhanced methane production in sewage and biogas plants. Exploratory; Roetning med inledande biologiskt hydrolyssteg foer utoekad metanutvinning paa avloppsreningsverk och biogasanlaeggningar. Foerstudie

    Energy Technology Data Exchange (ETDEWEB)

    2010-03-15

    Anaerobic degradation of organic matter is a multi-step process through the action of various groups of microorganisms whose optimum conditions can differ considerably regarding e.g. nutrients, pH demand, sensitivity for changes and patterns for growth and nutrient uptake. One way of optimizing the anaerobic digestion process, and thereby increase the biogas production and the reduction of organic matter, can be to physically divide the anaerobic digestion process in two steps consisting of an initial hydrolysis and acid production step followed by a methane production step in an anaerobic digester. One problem with the biogas processes of today is that not all organic matter that is added to the process becomes available for conversion into biogas. This is particularly evident in digestion of waste water treatment sludge where almost half of the organic matter added remains after anaerobic digestion. More efficient utilization of substrate in biogas plants is an important element to increase the profitability of biogas production. The possibility to use different pre-treatment methods is being discussed to increase the degree of conversion of organic matter into biogas in the digester. Pre-treatment methods are often energy as well as cost demanding and can require the addition of chemicals. To use the microbiological steps in the biogas process more efficiently by adding an initial hydrolysis step is a method that does not require the usage of chemicals or increased energy consumption. This pre-study is based on literature studies related to anaerobic digestion with initial biological hydrolysis and collected knowledge from full-scale plants, universities and suppliers of equipment. Nearly 70 published scientific articles relevant to the subject have been found in the performed literature searches. The articles have been subdivided according to the purpose of each article. A large part of the articles have concerned modelling of anaerobic digestion why a separate

  18. The conditions for use of reed canary grass briquettes and chopped reed canary grass in small heating plants; Foerutsaettningar foer anvaendning av roerflensbriketter och hackad roerflen i mindre vaermecentraler

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne; Davidsson, Kent; Holmgren, Magnus A. (Swedish National Testing and Research Inst., Boraas (Sweden)); Hedman, Henry; Oehman, Rikard; Leffler, Joel (ETC, Piteaa (Sweden))

    2010-09-15

    The aim of this study was to test fuel blends of briquettes and chopped reed canary grass in three existing heating plants (50 kW - 500 kW) and elucidate the requirements for good performance and low emissions. In addition, the study investigated production of reed canary grass briquettes using a Polish screw press developed for straw. Some tests with a bale shredder were also undertaken. The screw press technique is of interest for reed canary grass because it is a simple technique, easy to handle, developed for small scale production, and for straw. The test with reed canary grass in this study showed that the technique worked well but that further adjustments and a longer test period are needed in order to achieve higher bulk density and mechanical strength. The test with chopped reed canary grass shows that a system with a forage harvester is slightly more effective than baling and cutting in a bale shredder. The study concluded that few existing heating plants of size 50 kW-1 MW that currently use wood fuels will be able to use reed canary grass without adjustment, conversion or replacement of the combustion equipment. Reed canary grass has 15-20 times higher ash content than wood briquettes and 2-3 times higher ash content than forest residue; the combustion equipment must be able to handle these properties. The boiler must be equipped with a continuously operating ashing system and it must be possible to move the ash bed mechanically. There is a risk of high content of unburned matter if the residence time in the boiler is too short, due to the structure and low bulk density of the reed canary grass ash. Using a blend of wood briquettes and reed canary briquettes results in lower ash content, but also affects the ash chemistry and tends to lower the initial ash fusion temperature compared to using 100 % reed canary grass. Blending chopped reed canary grass and wood chips in an existing small scale heating plant also requires measures to achieve an even fuel

  19. Optimized raw material usage and utilization degree in a polygeneration plant for heat, electricity, biofuel and market fuel; Optimal raavaruinsats och utnyttjandegrad i energikombinat foer vaerme, el, biodrivmedel och avsalubraensle

    Energy Technology Data Exchange (ETDEWEB)

    Jennie Rodin; Olle Wennberg; Mikael Berntsson; Rolf Njurell; Ola Thorson

    2012-01-15

    Energy and economic efficiency for six different types of energy combines which include heat, electricity, pellets and fuel production have been studied. The basic case is a conventional power plant, which subsequently is expanded with various additional facilities (dryer, pellets and/or fuel). Maximum exploitation of the product against inserted biofuel was obtained in case 6, pulp mills that use waste heat for district heating supply and drying of bark. Case 6 had also the lowest payoff period; two years. Of the CHP [combined heat and power] based energy combines 'the big combine' with four different products generally showed best marginal efficiency and economy. The results indicate that drying may be an economical way to extend the operating season and increase the production of electricity in a CHP based energy combine.

  20. Noise and noise disturbances from wind power plants - Tests with interactive control of sound parameters for more comfortable and less perceptible sounds; Buller och bullerstoerningar fraan vindkraftverk - Foersoek med interaktiv styrning av ljudparametrar foer behagligare och mindre maerkbara ljud

    Energy Technology Data Exchange (ETDEWEB)

    Persson-Waye, K.; Oehrstroem, E.; Bjoerkman, M.; Agge, A. [Goeteborg Univ. (Sweden). Dept. of Environmental Medicine

    2001-12-01

    In experimental pilot studies, a methodology has been worked out for interactively varying sound parameters in wind power plants. In the tests, 24 persons varied the center frequency of different band-widths, the frequency of a sinus-tone and the amplitude-modulation of a sinus-tone in order to create as comfortable a sound as possible. The variations build on the noise from the two wind turbines Bonus and Wind World. The variations were performed with a constant dba level. The results showed that the majority preferred a low-frequency tone (94 Hz and 115 Hz for Wind World and Bonus, respectively). The mean of the most comfortable amplitude-modulation varied between 18 and 22 Hz, depending on the ground frequency. The mean of the center-frequency for the different band-widths varied from 785 to 1104 Hz. In order to study the influence of the wind velocity on the acoustic character of the noise, a long-time measurement program has been performed. A remotely controlled system has been developed, where wind velocity, wind direction, temperature and humidity are registered simultaneously with the noise. Long-time registrations have been performed for four different wing turbines.

  1. Calculation of additional costs in 2010 - for the demolition of the Swedish nuclear power plants and disposal of residues; Beraekning av merkostnader 2010 - foer rivning av de svenska kaernkraftsverken och omhaendertagande av restprodukter

    Energy Technology Data Exchange (ETDEWEB)

    Brewitz, Erica; Schoultz, Christian; Wetzel, Carina

    2010-09-15

    This report describes the SSM's calculation of additional costs for fee proposal for 2012-2014. The calculation is made pursuant to the Financing Act and includes all additional costs until the residue from the Swedish nuclear power plants is disposed of. According to current calculations, this should be done in 2069. Estimates of such a long time means a great deal of uncertainty and SSM uses, like SKB, the successive calculation method to estimate an expected value and tax association uncertainty. As a starting point for analysis, the SSM has made estimates of the future costs broken down into paragraphs in paragraph 2 Financing Act. The estimates were made after discussions within the organization and representatives of relevant external organizations. Assuming a total annual cost per worker of 1.24 million gave these estimates a total cost of over three billion. It should be emphasized that this sum is only a starting point for analysis and applies in particular circumstances. These circumstances critically reviewed the analysis and the reasonableness of assessments made by a analysis group. The analysis took place for 2.5 days in spring 2010. The analysis group consisted of 17 people including nine from the SSM. Lores Borg and Steen Lichtenberg were moderators. Via a brainstorming process, the analysis group presented a number of uncertainties and made a three-part assessment of their impact on the overall results (minimum, most likely and maximum). The result of the analysis: average in the 2010 monetary value was assessed to 4.24 billion Swedish crowns with a standard deviation of 920 million Swedish crowns. These values are undiscounted

  2. Small scale pelletizing equipment for agriculture; Smaaskalig pelleteringsanlaeggning foer lantbruket

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne (The Swedish Environmental Research Inst. Ltd., Stockholm (Sweden)); Wallin, Mikael (Sweden Powers Chippers AB, Boraas (Sweden))

    2009-06-15

    Refining agricultural raw materials is one way for farmers to increase the value of their products. For example, briquettes or pellets made from straw, reed canary grass or hemp can sell for a higher price than in loose or baled forms. The aim of this project was to develop and build a plant for small-scale production of pellets on the farm. Working together with the farmer, the plant would then be tested and adapted for small-scale production of pellets from straw, reed canary grass and hemp. The project also aimed to investigate and summarise suitable systems and solutions for breaking up bales in preparation for use in the pellets module. A pelleting system has been developed and built as a container module (measuring 6 x 2.80 x 2.50 m) by Sweden Power Chippers (SPC). The container system includes a fuel store with push floor, a grinder, an SPC pellet press (pp150, capacity 150 kg/hour for woodbased material), a conveyor belt and a cooling system. The practical operation of the plant was tested on two Swedish farms: Laattra gaard in Vingaaker and Ek gaard in Vara. The bales were broken up in preparation for pelleting using a straw mill of model Tomahawk 505M. The project has demonstrated that the SPC plant has the capacity to be used for agricultural pelleting of fuels from straw, canary reed grass and hemp. Some modification and continued adjustment of the feed system for the fuel remains to be done in order to optimise and ensure the reliability of the pelleting process. A certain amount of modifications to the plant is required to enable cost-effective transportation between different locations. Tests showed that each batch of fuel was unique, even from the same raw material, and that optimisation of the dies is necessary for each specific case. Training is required to run the plant. The farmers have been able to run the plant themselves, for example, starting up the plant, changing the sieve on the grinder, changing dies etc. In order for such small

  3. Inventory of future power and heat production technologies. Partial report Gasification with gas turbine/engine for power plants; Incl. English lang. appendix of 24 p. titled 'Status of large-scale biomass gasification for power production'; Inventering av framtidens el och vaermeproduktionstekniker. Delrapport Foergasning med gasturbin/motor foer kraftvaerk

    Energy Technology Data Exchange (ETDEWEB)

    Waldheim, Lars; Larsson, Eva K [TPS Termiska Processer, Nykoeping (Sweden)

    2008-12-15

    This subproject is limited to applications with gas turbines or engines from approximately 1 MWe and firing of gas in a boiler either as indirect cofiring or as separate firing of gas from waste gasification. Gasification with gas engine, BIG-ICE (Biomass Integrated Gasification Internal-Combustion Engine) is realized in approximately 10 plants in Europe between 1 and 7 MWe. The gas needs to be cleaned from particles and tar before it is fed to the engine. A number of different gasifiers and gas cleaning technologies are applied in these prototypes, and in certain cases a second generation is being built. Gas engines from GE Jenbacher are most common, but there are also other producers with engines for low-calorific-value gas. The exhausts from engines must, unlike gas turbines, be cleaned catalytically, but emissions of hydrocarbons in particular are still higher than from gas turbines. It is possible to increase the electricity generation by applying a 'bottoming cycle' in the form of a steam or an ORC cycle. Such a plant with ORC has been started in Austria this year. During the 1990's expectations were high concerning the development of biomass gasification with gas turbine in a combined cycle BIG-CC (Biomass Integrated Gasification Combined Cycle) towards commercialisation. Two demonstration plants were built for the same gas turbine model, Siemens SGT 100 (earlier Typhoon); Vaernamo with pressurised gasification and ARBRE in Eggborough, England, with atmospheric gasification. The atmospheric technology has basically the same demands on gas cleaning as in the engine application, but downstream the gas is compressed to the pressure required by the gas turbine. In pressurised gasification, the gasifier pressure is set by the gas turbine. The gas is not cooled below 350-400 deg C and is cleaned in a high-temperature filter. Despite successful demonstration in Vaernamo, no more plants have been built. The ARBRE plant was never put into regular operation because of

  4. Inventory of future power and heat production technologies. Partial report Gasification with gas turbine/engine for power plants; Incl. English lang. appendix of 24 p. titled 'Status of large-scale biomass gasification for power production'; Inventering av framtidens el och vaermeproduktionstekniker. Delrapport Foergasning med gasturbin/motor foer kraftvaerk

    Energy Technology Data Exchange (ETDEWEB)

    Waldheim, Lars; Larsson, Eva K. (TPS Termiska Processer, Nykoeping (Sweden))

    2008-12-15

    This subproject is limited to applications with gas turbines or engines from approximately 1 MWe and firing of gas in a boiler either as indirect cofiring or as separate firing of gas from waste gasification. Gasification with gas engine, BIG-ICE (Biomass Integrated Gasification Internal-Combustion Engine) is realized in approximately 10 plants in Europe between 1 and 7 MWe. The gas needs to be cleaned from particles and tar before it is fed to the engine. A number of different gasifiers and gas cleaning technologies are applied in these prototypes, and in certain cases a second generation is being built. Gas engines from GE Jenbacher are most common, but there are also other producers with engines for low-calorific-value gas. The exhausts from engines must, unlike gas turbines, be cleaned catalytically, but emissions of hydrocarbons in particular are still higher than from gas turbines. It is possible to increase the electricity generation by applying a 'bottoming cycle' in the form of a steam or an ORC cycle. Such a plant with ORC has been started in Austria this year. During the 1990's expectations were high concerning the development of biomass gasification with gas turbine in a combined cycle BIG-CC (Biomass Integrated Gasification Combined Cycle) towards commercialisation. Two demonstration plants were built for the same gas turbine model, Siemens SGT 100 (earlier Typhoon); Vaernamo with pressurised gasification and ARBRE in Eggborough, England, with atmospheric gasification. The atmospheric technology has basically the same demands on gas cleaning as in the engine application, but downstream the gas is compressed to the pressure required by the gas turbine. In pressurised gasification, the gasifier pressure is set by the gas turbine. The gas is not cooled below 350-400 deg C and is cleaned in a high-temperature filter. Despite successful demonstration in Vaernamo, no more plants have been built. The ARBRE plant was never put into regular

  5. Substrate Handbook for Biogas Production; Substrathandbok foer biogasproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Carlsson, My; Uldal, Martina (AnoxKaldnes AB, Lund (Sweden))

    2009-02-15

    Today, co-digestion plants in Sweden treat a broad range of different substrates, of which some have not previously been used for anaerobic digestion. The major part of this organic waste derives from households, restaurants, food industries and farms. When evaluating a new substrate as feed for anaerobic digestion, several different aspects need to be taken into consideration, such as anaerobic degradability, TS/VS content, nutrient composition and risk for mechanical problems. Consequently, there is a need for practical guidelines on how to evaluate new substrates as raw materials for biogas production, including not only gas yield but also what practical and microbiological problems that may arise when the specific substrate is treated together with other substrates in the plant. The aim with this handbook is to provide a basis on how to evaluate new substrates as feed for anaerobic digestion. The intention is that this material will save time and effort for the personnel at the plant when they come in contact with new types of waste. Also, the aim is to facilitate the process of identifying new substrates within the ABP-regulation (1774/2002) and what requirements are then demanded on handling. The work with the handbook has been divided in three different parts; (1) an extensive literature study and a compilation of the achieved results, (2) interviews with personnel at most of the Swedish co-digestion plants to identify substrates and problems of interest, and (3) lab tests of selected substrates. The lab tests included Bio Methane Potential (BMP) tests as well as a simple characterization of each substrate based on fat/protein/carbohydrate content. All data origins from anaerobic digestion within the mesophilic temperature range, but the results and discussion are applicable also for thermophilic anaerobic digestion. The result of this work is a written report together with an Excel file which are to be directly used by the biogas plants as a basis in the

  6. What became of the spruce planted on farmland? Survival, damage, quality, yield and economy in commercial plantations established in six counties in the south and middle of Sweden during 1968-73; Hur har det gaatt foer aakermarksgranen? Oeverlevnad, skador, kvalitet, tillvaext och ekonomi i praktiska planteringar anlagda under aaren 1968-73 i sex laen i soedra och mellersta Sverige

    Energy Technology Data Exchange (ETDEWEB)

    Malmqvist, Cecilia

    1997-12-31

    Different types of damage, branch quality, survival and yield were studied in 74 randomly chosen commercial plantations of Norway spruce on abandoned farmland. Economic calculations were made to supplement the results of the inventory. The stands, situated in south and middle of Sweden, were planted between 1968 and 1973. Survival in the stands had a wide range as well as yield. Frequency of damage was generally high, the most common types being spike knots and concentration of branches, but frost injuries, stem cracks, damage on the crown and stem, etc. were noted as well. The yield in economic terms is uncertain, except for the stands that grew fastest With 5 page summary in English. 59 refs, 28 figs, 18 tabs

  7. Water and steam sampling systems; Provtagningssystem foer vatten och aanga

    Energy Technology Data Exchange (ETDEWEB)

    Hellman, Mats

    2009-10-15

    The supervision of cycle chemistry can be divided into two parts, the sampling system and the chemical analysis. In modern steam generating plants most of the chemical analyses are carried out on-line. The detection limits of these analyzers are pushed downward to the ppt-range (parts per trillion), however the analyses are not more correct than the accuracy of the sampling system. A lot of attention has been put to the analyzers and the statistics to interpret the results but the sampling procedures has gained much less attention. This report aims to give guidance of the considerations to be made regarding sampling systems. Sampling is necessary since most analysis of interesting parameters cannot be carried out in- situ on-line in the steam cycle. Today's on-line instruments for pH, conductivity, silica etc. are designed to meet a water sample at a temperature of 10-30 deg C. This means that the sampling system has to extract a representative sample from the process, transport and cool it down to room temperature without changing the characteristics of the fluid. In the literature research work, standards and other reports can be found. Although giving similar recommendations in most aspects there are some discrepancies that may be confusing. This report covers all parts in the sampling system: Sample points and nozzles; Sample lines; Valves, regulating and on-off; Sample coolers; Temperature, pressure and flow rate control; Cooling water; and Water recovery. On-line analyzers connecting to the sampling system are not covered. This report aims to clarify what guidelines are most appropriate amongst the existing ones. The report should also give guidance to the design of the sampling system in order to achieve representative samples. In addition to this the report gives an overview of the fluid mechanics involved in sampling. The target group of this report is owners and operators of steam generators, vendors of power plant equipment, consultants working in

  8. Optimizing reed canary grass cropping to increase profitability. Field studies of plant varieties, intercropping with legumes and barley, fertilization and soil compaction; Optimering av odlingsaatgaerder i roerflen foer oekad loensamhet. Faeltstudier av sorter, samodling med baljvaexter och korn, goedsling samt markpackning

    Energy Technology Data Exchange (ETDEWEB)

    Palmborg, Cecilia; Lindvall, Eva (Swedish Univ. of Agricultural Sciences, Umeaa (Sweden). Agricultural Research for Northern Sweden)

    2010-05-15

    Reed Canary Grass is a promising crop for biofuel production. For reed canary grass the first year is an establishment year when the small biomass is not harvested. The second year the biomass is usually cut in late autumn but the harvest (removal of the biomass from the field) is delayed until spring. This technique has resulted in lower costs and increases in fuel quality through lower ash contents, including lower contents of chlorine, sodium and potassium. However costs for production are still high, especially establishment costs, fertilization costs and harvesting costs. The aim of this project was to test ways to cut costs per MWh by increased yields, and decreased establishment costs. The methods used have been variety trials to develop more productive plant material, intercropping with nitrogen fixing legumes to reduce the nitrogen demand of the crop, fertilization with waste material (sewage sludge, reed canary grass ash or poultry manure) and harvest at frozen ground as a strategy to reduce soil compaction and harvest damages on the crop. Reed canary grass grown as a fuel has so far been grown as a mono culture. However, when it is been grown for forage, or as a biogas crop, intercropping with legumes has been successful in some studies. In addition to NPK-fertilizers sewage sludge, ash from combustion of reed canary grass and poultry manure was used. An economic calculation showed that the establishment costs (the first two growing seasons) can be lowered by intercropping with red clover. However it is also involves more risks, related to weeds, and cannot be recommended on fallow soil with a large seed bank of weeds. A ten year old reed canary grass ley was used for the experiment. Two 25 m wide strips were harvested with a mower on November 19 2008 when the top soil was frozen. The harvested material was chopped and removed from the field the following day. The following spring, May 19 2009, the remaining reed canary grass on the field was cut with a

  9. Preliminary plan for decommissioning - repository for spent nuclear fuel; Preliminaer plan foer avveckling - slutfoervar foer anvaent kaernbraensle

    Energy Technology Data Exchange (ETDEWEB)

    Hallberg, Bengt; Tiberg, Liselotte (Studsvik Nuclear AB, Nykoeping (Sweden))

    2010-06-15

    The final disposal facility for spent nuclear fuel is part of the KBS-3 system, which also consists of a central facility for interim storage and encapsulation of the spent nuclear fuel and a transport system. The nuclear fuel repository will be a nuclear facility. Regulation SSMFS 2008:1 (Swedish Radiation Safety Authority's regulations on safety of nuclear facilities) requires that the licensee must have a current decommissioning plan throughout the facility lifecycle. Before the facility is constructed, a preliminary decommissioning plan should be reported to the Swedish Radiation Safety Authority. This document is a preliminary decommissioning plan, and submitted as an attachment to SKB's application for a license under the Nuclear Activities Act to construct, own and operate the facility. The final disposal facility for spent nuclear fuel consists of an above ground part and a below ground part and will be built near Forsmark and the final repository for radioactive operational waste, SFR. The parts above and below ground are connected by a ramp and several shafts, e.g. for ventilation. The below ground part consists of a central area, and several landfill sites. The latter form the repository area. The sealed below ground part constitutes the final repository. The decommissioning is taking place after the main operation has ended, that is, when all spent nuclear fuel has been deposited and the deposition tunnels have been backfilled and plugged. The decommissioning involves sealing of the remaining parts of the below ground part and demolition of above ground part. When decommissioning begins, there will be no contamination in the facility. The demolition is therefore performed as for a conventional plant. Demolition waste is sorted and recycled whenever possible or placed in landfill. Hazardous waste is managed in accordance with current regulations. A ground investigation is performed and is the basis for after-treatment of the site. The timetable

  10. Human Factors methods concerning integrated validation of nuclear power plant control rooms; Metodutveckling foer integrerad validering

    Energy Technology Data Exchange (ETDEWEB)

    Oskarsson, Per-Anders; Johansson, Bjoern J.E.; Gonzalez, Natalia (Swedish Defence Research Agency, Information Systems, Linkoeping (Sweden))

    2010-02-15

    The frame of reference for this work was existing recommendations and instructions from the NPP area, experiences from the review of the Turbic Validation and experiences from system validations performed at the Swedish Armed Forces, e.g. concerning military control rooms and fighter pilots. These enterprises are characterized by complex systems in extreme environments, often with high risks, where human error can lead to serious consequences. A focus group has been performed with representatives responsible for Human Factors issues from all Swedish NPP:s. The questions that were discussed were, among other things, for whom an integrated validation (IV) is performed and its purpose, what should be included in an IV, the comparison with baseline measures, the design process, the role of SSM, which methods of measurement should be used, and how the methods are affected of changes in the control room. The report brings different questions to discussion concerning the validation process. Supplementary methods of measurement for integrated validation are discussed, e.g. dynamic, psychophysiological, and qualitative methods for identification of problems. Supplementary methods for statistical analysis are presented. The study points out a number of deficiencies in the validation process, e.g. the need of common guidelines for validation and design, criteria for different types of measurements, clarification of the role of SSM, and recommendations for the responsibility of external participants in the validation process. The authors propose 12 measures for taking care of the identified problems

  11. Model for economic optimization of solar power plants; Beraekningsmodell foer ekonomisk optimering av solelanlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Widen, Joakim

    2011-01-15

    This is the final report from a project in which an early-design-phase tool for photovoltaic (PV) systems has been developed. The aim of the tool is to provide a quick and easy way to estimate the electricity production and the economy of a PV system. Although it is effective and easy to use, the model takes into account all the important factors that affect the design, performance and economy of a system, and makes it possible with more in-depth analyses as well. The intended users of the tool are both electricity end-users thinking on investing in a small-scale system and large investors planning in an early project phase for large-scale PV systems. The developed tool is a simulation tool rather than an optimization tool. However, as the model is efficient and simple to use, it is easy to vary parameters and input data in different scenarios to arrive at an optimal solution. In order for the tool to realistically estimate the load matching of a PV system, which depends on seasonal and diurnal variations in both load and production profiles, the computations are made on an hourly basis. An hourly resolution is the most common one in meteorological data and to increase the resolution further is neither practically possible nor required for accuracy. The hourly irradiation data used in the model were collected from the publicly available STRAaNG database, which is maintained by the Swedish Meteorological and Hydrological Institute (SMHI). Idealized hourly load profiles for typical Swedish end-user categories are also included in the tool. A general computational model was implemented in Matlab, which provided easy testing, visualization and validation of the model. The computations involved can be summarized in four main steps: 1 Radiation computations. This involves a transposition of radiation components to the tilted plane of the PV array. The model takes the orientation of the system into account and uses assumed albedo values of the surroundings to add ground-reflected radiation. 2 PV system simulations. A simplified model of the PV system, including different loss mechanisms, is used to convert incident radiation to a power output from the system inverter. 3 Electricity use and load matching analyses. The interaction with the electricity distribution grid is determined from the power production and load profiles. 4 Economical analysis. The economy of the system is determined from the load matching analysis and depends on system costs, subsidies and different debiting and net metering alternatives. The exact model computations are summarized in Appendix A-D. The model has been compared to both the commercial tool PVSYST 4.1 and to empirical measurements on PV systems in the Swedish climate. The conclusion is that the performance of the developed model is similar to that of the commercial tool, although more in-depth analyses and extensive fine tuning of parameters can be done in PVSYST. The annual production and performance ratio of a typical system in the model is close to the production and average performance of a set of measured Swedish PV test systems. The model structure was implemented in the object-oriented programming language Java SE 6 with Java Web Start, which enables the creation of a platform-independent application with a graphical user interface that can be started from a web site without any requirements on local Java installations. The implemented model is with few exceptions identical to the one that was tested in Matlab. This application will be publicly available on the Elforsk website. In the report, the application is used to show how one small-scale and one large-scale system can be modeled and analysed

  12. Methodology - evaluation of strategies -and the system for taking care of spent nuclear fuel; Metodval - utvaerdering av strategier och system foer att ta hand om anvaent kaernbraensle

    Energy Technology Data Exchange (ETDEWEB)

    2010-10-15

    This report deals with the question of how the Swedish spent nuclear fuel is to be disposed of. What are the requirements? What are the alternatives? In the main chapter of the report, an evaluation is made of the KBS-3 method compared with other strategies and systems for final disposal of spent nuclear fuel. An appendix to the report presents in general terms how the KBS-3 method has developed from the end of the 1970s up to today. The report is one of a number of supporting documents for SKB's applications for construction and operation of the final repository for spent nuclear fuel. In parallel with and as a basis for the present report, SKB has prepared the reports 'Principer, strategier och system foer slutligt omhaendertagande av anvaent kaernbraensle' ('Principles, strategies and systems for final disposal of spent nuclear fuel') /Grundfelt 2010a/, 'Jaemfoerelse mellan KBS-3-metoden och deponering i djupa borrhaal foer slutlig foervaring av anvaent kaernbraensle' ('Comparison between the KBS-3 method and deposition in deep boreholes for final disposal of spent nuclear fuel') /Grundfelt 2010b/ and 'Utvecklingen av KBS-3-metoden. Genomgaang av forskningsprogram, saekerhetsanalyser, myndighetsgranskningar samt SKB:s internationella forskningssamarbete' ('Development of the KBS-3 method. Review of research programmes, safety assessments, regulatory reviews and SKB's international research cooperation') /SKB 2010a/. The reports are in Swedish, but contain summaries in English. The first report is an update of the comprehensive account of alternative methods presented by SKB in 2000. The second report presents a comparison between the KBS-3 method and the Deep Boreholes concept, plus a status report on research and development in the area of Deep Boreholes. The last report describes how the KBS-3 method has been developed from the end of the 1970s up to today. It further describes how the

  13. Long-time effects of run-off water from ash recycling to a planted forest. Final report for a partial study in the project 'Forestry measures - effects on carbon-, nutrients and heavy metal flows' financed by the Swedish Energy Agency; Laangtidsverkan paa avrinnande vatten av askaaterfoering till plantskog. Slutrapport foer en delstudie inom det av Energimyndigheten finansierade projektet 'Skogliga aatgaerder - effekter paa kol-, naering och tungmetalIfloeden'

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Torbjoern; Eriksson, Hillevi

    2001-06-01

    The chemical composition of runoff from a wood ash fertilized catchment in central Sweden has been studied during eight years after the treatment. The effects of the ash treatment was compared with a 12 year long reference period and a reference catchment close to the ash treated area was earlier (winter 1980/81) whole-tree-harvested to 90 %. At the same time the reference area was stemwood harvested on 60 % of the area. Both areas were planted with spruce and pine. Granulated ash was spread on the whole-tree-harvested area, by helicopter, on two occasions (1 ton per hectare in May 1989 and 2 tonnes per hectare in October 1991). During the first ash application a marked peak in K concentration was observed. The second ash application caused a high peak in K concentration. Short-lived peaks was also observed for pH, electric conductivity, ANC, Mg, Na and Cl. Significant increases of pH, electric conductivity, Ca, K and Cl was observed in runoff water from the ash treated area during the 8-year-period after the last ash spreading. However, during the same period concentrations of NH{sub 4}-N, NO{sub 3}-N and total N have shown a relative decrease in runoff water from the ash treated area, compared to the reference area.

  14. Conditions for new biofuel raw materials. Systems for small scale briquetting and pelletizing; Foerutsaettningar foer nya biobraensleraavaror. System foer smaaskalig brikettering och pelletering

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne; Holmgren, Kristina (The Swedish Environmental Research Institute Ltd., Stockholm (Sweden)); Rosenqvist, Haakan; Boerjesson, Paal (Environmental and Energy Systems Studies, Lund Inst. of Technology, Lund (Sweden))

    2009-01-15

    The increasing demand for biomass has driven exploitation of the most easily available and cheapest biomass resources such as sawmill waste and logging residues. More knowledge is needed about exploitation and production of potential new biomass resources, currently not used for energy production (or only to a very small extent), in order to meet the future demands from various biomass users. The project aimed to examine the conditions for use of 'new' biomass materials for heat production from technical, economic and other perspectives (price trends, attitudes etc.). More specifically, the study looked at which biomass raw materials have the best characteristics for processing into briquettes and pellets in small-scale production plants (1 000 - 10 000 tonnes fuel produced per year) situated close to the source of the raw material. The study includes a comprehensive analysis of the appropriateness of the different raw materials and a case study including cost estimates for the entire production chain for production of briquettes from reed canary grass on a chosen farm (Laattra gaard). The raw materials judged to have potential to supplement the current biomass range for heat production are willow (and to a certain extent other fast-growing hardwoods), straw and reed canary grass. In the future, other perennial grasses may be of interest. Other forestry products that may help to meet in creasing demand include logging residues, stumps and wood from thinning and precommercial thinning. The study shows that the prerequisites for processing these raw materials into briquettes and pellets in small-scale production plants are relatively good from several aspects (technology, economics, market) but are limited by the types of end user that can use that form of biomass. The study concluded that straw has a low production cost and good prerequisites as a raw material for production of fuel briquettes, fuel pellets and horse bedding pellets. However, use is

  15. Nordel - Availability statistics for thermal power plants 1995. (Denmark, Finland, Sweden)

    International Nuclear Information System (INIS)

    1996-01-01

    The power companies of Denmark, Finland and Sweden have agreed on almost identical procedures for the recording and analysing of data describing the availability of power producing units over a certain capacity. Since 1975 the data for all three countries have been summarized and published in a joint report. The purpose of this report is to present some basic information about the operation of power producing units in the three countries. Referring to the report, companies or bodies will be able to exchange more detailed information with other companies or bodies in any of the countries. The report includes power producing units using fossil fuels, nuclear power plants and gas turbines. The information is presented separately for each country with a joint NORDEL statistics for units using fossil fuels, arranged in separate groups according to the type of fossil fuel which is used. The grouping of power producing units into classes of capacity has been made in accordance with the classification adopted by UNIPEDE/WEC. The definitions in NORDEL's 'Tillgaenglighetsbegrepp foer vaermekraft' ('The Concept of Availability for Thermal Power'), September 1977, are used in this report. The basic data for the availability are in accordance with the recommendations of UNIPEDE/WEC. (author)

  16. Pilot study of Bio-jet A-1 fuel production for Stockholm-Arlanda Airport; Foerstudie foer biobaserat flygbraensle foer Stockholm-Arlanda Flygplats

    Energy Technology Data Exchange (ETDEWEB)

    Ekbom, Tomas; Hjerpe, Carl; Hagstroem, Martin; Hermann, Fredrik

    2009-11-15

    The air traffic industry faces big changes in the near future, one being how to reduce their share of the CO{sub 2}-emissions. Therefore LFV set the framework to investigate the pre-conditions for a biorefinery plant in conjunction with Arlanda Airport. The biorefinery is based on advanced gasification technology and Fischer-Tropsch synthesis to a bio-jet fuel product. Locations at Brista and Igelsta were studied for two different process plant configurations, with each 50 kton bio-jet fuel annual capacity, or 290 and 610 MW{sub th} biomass input, respectively. The biomass-to-fuels efficiency was 46 % and total net efficiency was 79 %. The capital investment was calculated as 5.1 and 7.4 billion SEK, and production costs of 8300 SEK (812 EUR/1183 USD) and 5000 SEK (490 EUR/714 USD) per cubic meter bio-jet, respectively, whereas the Jet A-1 fuel today costs some 6000 SEK, at crude oil price of USD 67 per barrel

  17. Demonstration program for small-scale straw fuel systems. Pre-study for the Swedish Energy Agency; Demonstrationsprogram foer smaaskaliga straabraenslesystem. Foerstudie foer Energimyndigheten

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne (Swedish Environmental Research Institute Ltd., Stockholm (Sweden)); Wahlberg, Cecilia (Hushaallningssaellskapet, Stockholm (Sweden)); Arkeloev, Olof (LRF Konsult, Stockholm (Sweden))

    2008-02-15

    Energy crops from arable land is still an almost entirely untapped potential as a fuel for heating. Canary grass, straw and hemp could eventually form an important part of the raw-material from agriculture. For this production to increase and become a viable alternative to conventional farming it is required, however, that the whole production chain from cultivation to end-use is developed. The aim of this pilot study has been to make suggestions for the design of a Demonstration project of small-scale fuel straw-crops. The programme's vision is to within 6 years build up a number of demonstration plants for small-scale briquetting/pelletizing of straw fuels in different parts of the country. In addition, potential producers of raw materials and other actors in the programme will be made aware what opportunities and conditions there are to process the agro-fuels in small-scale production facilities. The overall objective of the programme is to increase knowledge about how straw fuels and/or residues can be used as raw material in small-scale production of briquettes/pellets, and enhance the understanding of how producers take part in different business models. In the short term, the objective of the programme to build up a network of pellets and briquettes producing demonstration. Within the activities of the programme it is proposed that demonstration is built up of at least 7 different places in the country. This is in order to be able to gain experience on the basis of local and regional conditions. Demonstration refers both to demonstrate the entire chain with existing proven technology, and to improve technologies, reduce costs and make the production and user experience. On the other hand, the intention may be to test the new technology. Demonstration refers to smaller installations and with a production capacity of plants should vary from about 100 to 500 kg/h produced fuel. Operations are limited to the supply of raw material, cultivation and harvest

  18. Genetic variation for characters of importance for growth in Salix viminalis L. Final report; Genetisk variation foer karaktaerer av betydelse foer tillvaext hos Salix viminalis L. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Roennberg-Waestljung, Ann Christin; Gullberg, Urban [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Plant Biology

    2000-04-01

    The overall goal for this project was to study the genetic variation and the genetic relationships for different growth characters and for water use efficiency (WUE) in Salix viminalis and also to use this knowledge to formulate breeding goals for Salix. Two factorial crossings with Swedish and Polish origin, each with 320 families have been used. Part of the Polish material was used to study the genetic variation for carbon isotope quota. Carbon isotope quota gives a measure of the WUE for the plant. Crossings have been made to change and improve the WUE in Salix viminalis. Construction of a genetic linkage map has started and the map can be used to identify genetic markers for WUE. The results show that most of the growth characters have both additive genetic variation and also a high degree of dominance genetic variation. A strategy in the breeding where both additive and dominance variation can be utilized should be adopted. WUE show mainly additive genetic variation but also a high heritability. This gives great opportunities to improve Salix material for WUE through recurrent selection.

  19. Guidelines for water and steam adapted to Swedish energy plants; Riktvaerden foer vatten och aanga anpassade till svenska energianlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Hellman, Mats [Hellman Vatten AB, Haegersten (Sweden)

    2006-02-15

    The project summons a revision of the Swedish Cycle Chemistry Guidelines with the purpose to create guidelines that are more explicit and thereby easier to adapt to in daily operations. The objective in general has not been to tighten the limiting values; some are stricter but some others are less strict. The boilers of today are usually fed with demineralised water as make-up water which has been reflected in the guidelines. In this project consideration has been taken upon the fact that many boilers, mostly industrial, have been in operation for many years according to old guidelines, without problems. In these cases the boilers may very well continue to operate without any costly reinvestments due to the new guidelines. The most important revisions in the guidelines are: Action levels have been introduced for the core parameters in the water-steam cycle. With action levels the operators will have some guidance to correct deviations in the cycle chemistry. The action levels are progressive in the sense that the more serious deviation from the guidelines, the shorter time to correct the problem. Guidelines for boilers up to 6.0 MPa operating on softened make-up water have been adjusted slightly and introduced with action levels. New guidelines for boilers with demineralised make-up water have been compiled. Within the project group there is a consensus that demineralised make-up water is preferable even for low pressure boilers. Varying chemistry regimes are used in the industry today. This report gives guidelines for the three dominating in Sweden; All Volatile Treatment (AVT), Caustic Treatment and Phosphate Treatment. Cation conductivity is a core parameter for supervision of steam quality for turbine operation, and in all international guidelines cation conductivity is included. However, the cation conductivity can rise above limits if organic dosing agents are used. This may be accepted as long as the pH-value is within the specifications and it can be shown that the high cation conductivity is not caused by excessive levels of aggressive salts.

  20. Technology and costs for decommissioning Swedish nuclear power plants; Teknik och kostnader foer rivning av svenska kaernkraftverk

    Energy Technology Data Exchange (ETDEWEB)

    Hedin, Gunnar; Gustavsson, Boerje [Westinghouse Electric Sweden AB, Vaesteraas (Sweden); Carlsson, Jan [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

    2004-06-01

    SKB has already performed three studies on available technology and approximate costs for decommissioning Swedish NPPs (years 1986, 1994 and 2000). The present report is an update of the year 2000 report with emphasis on areas that have been studied since the publication of that report. The report also gives a review of the technologies that have been chosen for decommissioning the Swedish reactors. The cost-estimation has also been updated and indexed to the present monetary situation. Areas in need for further studies are pointed in the report.

  1. Preconditions for the development of land-based infrastructure for liquefied natural gas (LNG / LBG); Foerutsaettningar foer utbyggnad av landbaserad infrastruktur foer flytande gas (LNG/LBG)

    Energy Technology Data Exchange (ETDEWEB)

    Stenkvist, Maria; Paradis, Hanna; Haraldsson, Kristina; Beijer, Ronja; Stensson, Peter (AaF Industry AB(Sweden))

    2011-06-15

    The conversion potential to replace oil in the energy intensive industries and diesel in heavy transport is estimated in the study to 6.8 TWh and 10 TWh per year, respectively. Several alternative fuels compete for this conversion potential. What fuels will take market share depends on several factors such as price, availability of fuel, availability of process technology and vehicles, technology development and possible future technological advances. For liquid methane to compete a new infrastructure is required that in a cost effective manner makes it possible to distribute the liquid methane to the regions where the need is the greatest. With today's distribution system, including truck delivery from import terminals in Nynaeshamn and Fredrikstad, virtually the entire southern Sweden is within reach of LNG deliveries. The study points out three nodes, Gaevle, Sundsvall and Luleaa, which is suitable for distribution of liquid methane to the central and northern Sweden. The three hubs are suitable for freight transfer to trucks as well as rail and shipping. A strategic nationwide network of refueling stations is also proposed, with a total of 18 new stations, in addition to the filling stations in southern and central Sweden that are already planned or in operation. Both the availability and use of liquid methane in Sweden today is limited. Liquid natural gas, LNG (liquefied natural gas), is primarily used as a backup to biogas plants, in a few industries and as supply for a few filling stations for compressed gas. The availability of LNG and also liquid biogas (LBG liquefied biogas), will increase in coming years. In 2011, two new LNG import terminals are put into operation in Nynaeshamn and Fredrikstad in Norway and two additional import terminals are planned in Gothenburg and Lysekil. Furthermore, two production plants for liquid biogas production have started, and four additional plants are planned, which together will produce around 0.5 TWh LBG annually

  2. Survey of biological processes for odor reduction; Kartlaeggning och studie av biologiska processer foer luktreduktion

    Energy Technology Data Exchange (ETDEWEB)

    Arrhenius, Karine; Rosell, Lars [SP Technical Research Inst. of Sweden, Boraas (Sweden); Hall, Gunnar [SIK Swedish Inst. for Food and Biotechnology, Gothenburg (Sweden)

    2009-09-15

    This project aims to characterize chemical and subsequently odor emissions from a digester plant located closed to Boraas in Sweden (Boraas Energi och Miljoe AB). The digestion produces mainly 2 by-products, biogas and high quality organic biofertilizer. Biogas is a renewable source of electrical and heat energy and subsequently digester have a promising future. Unfortunately, release of unpleasant odours is one of the problems that may limit development of the technique as odours strongly influence the level of acceptance of the neighbours. The number of complaints due to odours depends mostly, upon the degree of odour release, the weather condition and plant environment (which influence the risks for spreading out), and the tolerance of the neighbours. These parameters are strongly variable. Many processes inside the plant distributed on a large surface may contribute to odour release. Chemical emissions were studied, in this project, by extensive sampling inside the plant. Results were then evaluated regarding risk for odour releases. The goal was to suggest controls and routines to limit releases. The conditions leading to the higher risks for odour emissions were studied by performing sampling at different periods of the year and subsequently different weather conditions. At first, places for measurement were chosen together with personal of the plant. Three zones are considered to mainly contribute to the odour emissions: the landfill region, the cisterns region and the leaching lake region. Totally 13 places were studied with regard to odour and chemical emissions under 2008-2009 at different weather conditions. Some results from a previous project (2007) are also presented here. Results show that the spreading out of can be maintained to an acceptable level as long as the plant is functioning without disturbances. The early stages of the treatment of waste should be confined in locals with closed doors to avoid spreading out of odours. Through controlled

  3. Laws for local energy systems. A review; Lagar foer lokala energisystem. En oeversikt

    Energy Technology Data Exchange (ETDEWEB)

    Bylund, S I [Bygginfo AB, Stockholm (Sweden); Moe, N; Bjoerk, J [Swedish National Board for Industrial and Technical Development (NUTEK), Stockholm (Sweden); Goethe, S; Froste, H [Swedish Environmental Protection Agency, Solna (Sweden); Larsen, B; Gyberg, A [Boverket, Karlskrona (Sweden)

    1996-10-01

    This report gives a popular descriptive orientation of existing laws regarding the establishment of small-scale energy technology, like wind power plants, heat pumps, solar heating and others, and also of more efficient power generation. In the first part of the report 11 different local energy systems are described, together with their environmental impact. The second part gives a review of more than 20 laws. The central content of the laws are described, not the complete text

  4. Optimized district heating supply temperature for large networks; Optimerad framledningstemperatur foer stora fjaerrvaermenaet

    Energy Technology Data Exchange (ETDEWEB)

    Saarinen, Lisa; Boman, Katarina

    2012-02-15

    The supply temperature of the Uppsala district heating network was optimized using a model-based control strategy. Simulation of the network showed that the supply temperature could be decreased by in average 8 deg and the electricity production of the plants supplying the network could be increased with 2.5 % during the period January- April, giving an extra income of 1.2 MSEK due to increased income from electricity sales

  5. Model for safety reports including descriptive examples; Mall foer saekerhetsrapporter med beskrivande exempel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    Several safety reports will be produced in the process of planning and constructing the system for disposal of high-level radioactive waste in Sweden. The present report gives a model, with detailed examples, of how these reports should be organized and what steps they should include. In the near future safety reports will deal with the encapsulation plant and the repository. Later reports will treat operation of the handling systems and the repository.

  6. IR sensor for monitoring of burner flame; IR sensor foer oevervakning av braennarflamma

    Energy Technology Data Exchange (ETDEWEB)

    Svanberg, Marcus; Funkquist, Jonas; Clausen, Soennik; Wetterstroem, Jonas

    2007-12-15

    To obtain a smooth operation of the coal-fired power plants many power plant managers have installed online mass flow measurement of coal to all burners. This signal is used to monitor the coal mass flow to the individual burner and match it with appropriate amount of air and also to monitor the distribution of coal between the burners. The online mass flow measurement system is very expensive (approximately 150 kEUR for ten burners) and is not beneficial for smaller plants. The accuracy of the measurement and the sample frequency are also questionable. The idea in this project has been to evaluate a cheaper system that can present the same information and may also provide better accuracy and faster sample frequency. The infrared sensor is a cheap narrow banded light emission sensor that can be placed in a water cooed probe. The sensor was directed at the burner flame and the emitted light was monitored. Through calibration the mass flow of coal can be presented. Two measurement campaigns were performed. Both campaigns were carried out in Nordjyllandsverket in Denmark even though the second campaign was planned to be in Uppsala. Due to severe problems in the Uppsala plant the campaign was moved to Nordjyllandsverket. The pre-requisites for the test plant were that online measurement of coal flow was installed. In Nordjyllandsverket 4 out of 16 burners have the mass flow measurement installed. Risoe Laboratories has vast experiences in the IR technology and they provided the IR sensing equipment. One IR sensor was placed in the flame guard position just behind the flame directed towards the ignition zone. A second sensor was placed at the boiler wall directed towards the flame. The boiler wall position did not give any results and the location was not used during the second campaign. The flame-guard-positioned-sensor- signal was thoroughly evaluated and the results show that there is a clear correlation between the coal mass flow and the IR sensor signal. Tests were

  7. Conditions for lowering the flue gas temperature; Foerutsaettning foer saenkning av roekgastemperatur

    Energy Technology Data Exchange (ETDEWEB)

    Nordling, Magnus

    2012-02-15

    In heat and power production, the efficiency of the power plant increases the larger share of heat from the flue gas that is converted to power. However, this also implies that the temperature of the heat exchanging surfaces is lowered. If the temperature is lowered to a temperature below the dew point of the flue gas, this would result in condensation of the gas, which in turn elevates the risk of serious corrosion attack on the surfaces where condensation occurs. Thus, it is important to determine the dew point temperature. One way of determining the dew point temperature is to use data on composition of the fuel together with operation parameters of the plant, thus calculating the dew point temperature. However, this calculation of the dew point is not so reliable, especially if hygroscopic salts are present. Therefore, for safety reasons, the temperature of the flue gas is kept well above the dew point temperature. This results in lowered over-all efficiency of the plant. It could also be expected that for a certain plant, some construction materials under certain operation conditions would have corrosion characteristics that may allow condensation on the surface without severe and unpredictable corrosion attack. However, by only using operation parameters and fuel composition, it is even harder to predict the composition of the condensate at different operation temperatures than to calculate the dew point temperature. If the dew point temperature was known with a greater certainty, the temperature of the flue gas could be kept lower, just above the estimated value of the dew point, without any increased risk for condensation. If, in addition, also the resulting composition of the condensate at different temperatures below the dew point is known, it can be predicted if the construction materials of the flue gas channel were compatible with the formed condensate. If they are compatible, the flue gas temperature can be further lowered from the dew point

  8. Legionella bacteria in combustion air humidifiers; Legionella i luftuppfuktare foer foerbraenningsluft

    Energy Technology Data Exchange (ETDEWEB)

    Jeppesen, Jessica; Hansson, Helen; Cederfeldt, Ola; Axby, Fredrik

    2007-10-15

    Over the last couple of years several outbreaks of Legionnaires' disease has occurred around the world. The source of infection varies, but in many cases the bacteria has been traced back to cooling towers. The common denominator for most of the sources of infection has been water systems with high oxygen levels and a system temperature ranging from 20 to 40 deg C. If a water system furthermore has high levels of other bacteria/microorganisms, then it is also probable that favorable conditions for legionella bacteria exist within the system. These conditions consist well with conditions in combustion air humidifiers in district heating plants and therefore it can be suspected that legionella may thrive also in these types of air humidifiers. In order to examine if legionella bacteria exists in combustion air humidifiers, and in what quantity, ten different district heating plants where selected for a survey. The goal of the survey is to get a general picture of the extent of the occurrence of legionella bacteria in different types of air humidifiers. This was done by taking legionella tests in three different types of air humidifiers in district heating plants. The first step of the testing was conducted by measuring the level of legionella bacteria in water samples from the air humidifiers in the different plants. The water samples were taken from water that circulates in the air humidifiers. A few months later another water sample was taken from the same location. Two district heating plants, where legionella bacteria had been detected, were selected for further testing after compiling the results from the first two tests. The further testing involved fuel gas analysis to see if any of the plants fuel gas contained legionella bacteria. The test results show that a major part of the district heating plants in the survey have heterotrophic bacteria in their water systems, which implies the possibility of growth of legionella bacteria. About half of the plants

  9. Robust on-line monitoring of biogas processes; Robusta maettekniker on-line foer optimerad biogasproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Nordberg, Aake; Hansson, Mikael; Kanerot, Mija; Krozer, Anatol; Loefving, Bjoern; Sahlin, Eskil

    2010-03-15

    Although demand for biomethane in Sweden is higher than ever, many Swedish codigestion plants are presently operated below their designed capacity. Efforts must be taken to increase the loading rate and guarantee stable operation and high availability of the plants. There are currently no commercial systems for on-line monitoring, and due to the characteristics of the material, including corrosion and tearing, robust applications have to be developed. The objective of this project was to identify and study different monitoring technologies with potential for on-line monitoring of both substrate mixtures and anaerobic digester content. Based on the prerequisites and demands at Boraas Energi och Miljoe AB's (BEMAB, the municipal energy and waste utility in the city of Boraas, Sweden) biogas plant, the extent of the problems, measurement variables and possible ways of managing these issues have been identified and prioritized. The substrate mixtures in question have a high viscosity and are inhomogeneous with variation in composition, which calls for further homogenization, dilution and filtration to achieve high precision in the necessary analyses. Studies of using different mixers and mills showed that the particle size (800 mum) needed for on-line COD measurement could not be achieved. The problem of homogenization can be avoided if indirect measurement methods are used. Laboratory tests with NIR (near-infra red spectroscopy) showed that VS can be predicted (R2=0,78) in the interval of 2-9% VS. Furthermore, impedance can give a measurement of soluble components. However, impedance is not sensitive enough to give a good measurement of total TS. Microwave technology was installed at the production plant and showed a faster response to changes in TS than the existing TS-sensor. However, due to technical problems, the evaluation only could be done during a limited period of ten days. BEMAB will continue the measurements and evaluation of the instrument. The

  10. Artificial neural networks for monitoring the gas turbine; Artificiella neuronnaet foer gasturbinoevervakning

    Energy Technology Data Exchange (ETDEWEB)

    Fast, Magnus; Thern, Marcus [Inst. foer Energivetenskaper, Lunds Univ. (Sweden)

    2011-10-15

    Through available historical operational data from gas turbines, fast, accurate, easy to use and reliable models can be developed. These models can be used for monitoring of gas turbines and assist in the transition from today's time-based maintenance to condition based maintenance. For the end user this means that, because only operational data is needed, they can easily develop their own tools independent of the manufacturer. Traditionally these types of models are constructed with physical relations for e.g., mass, energy and momentum. To develop a model with physical relations is often laborious and requires classified information which the end user does not have access to. Research has shown that by producing models using operational data a very high model precision can be achieved. When implementing these models in a power plant computer system the gas turbine's performance can be monitored in real time. This can facilitate fault detection at an early stage, and if necessary, stop the gas turbine before major damage occurs. For the power plant owner, this means that the gas turbine reliability is increased since the need for maintenance is minimized and the downtime is reduced. It also means that a measure of the gas turbine's overall status is continuously available, with respect to e.g. degradation, which helps in the planning of service intervals. The tool used is called artificial neural networks (ANN), a collective name for a number of algorithms for information processing that attempts to mimic the nerve cell function. Just like real networks of neurons in a brain, these artificial neural networks have the ability to learn. In this case, neural networks are trained to mimic the behavior of gas turbines by introducing them to data from real gas turbines. After a neural network is trained it represents a very accurate model of the gas turbine that it is trained to emulate.

  11. Place of the final disposal of short lived dismantling waste; Plats foer slutfoervaring av kortlivat rivningsavfall

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-01-15

    This report deals with the short-lived low and intermediate level radioactive waste, which will mainly arise from the dismantling of the Swedish nuclear power plants, but also the dismantling of other nuclear facilities. For these installations to be dismantled, there must be the capacity to receive and dispose of dismantling waste. SKB plans to expand the existing final repository for short-lived radioactive waste (SFR) in Forsmark for this purpose. The legislation requires alternatives to the chosen location. The alternate location for the disposal of decommissioning waste SKB has chosen to compare with is a location in the Simpevarp area outside Oskarshamn. There are currently Oskarshamn nuclear power plant and SKB between stock 'CLAB'. The choice of Simpevarp as alternative location is based on that it's one of the places in the country where data on the bedrock is available to an extent that allows an assessment of the prospects for long-term security, such an assessment is actually showing good potential, and that the location provide realistic opportunities to put into practice the disposal of decommissioning waste. At a comparison between the disposal of short-lived decommissioning waste in an extension of SFR with the option to build a separate repository for short-lived decommissioning waste in Simpevarp, the conclusion is that both options offer potentially good prospects for long-term security. The differences still indicated speaks to the Forsmark advantage. Similar conclusions were obtained when comparing the factors of environment, health and social aspects.

  12. Forecasts and restrictions on vibrations from rock excavation and transportation. Encapsulation Plant and Repository for spent nuclear fuel, Laxemar; Prognoser och restriktioner foer vibrationer fraan bergschaktning och transporter. Inkapslingsanlaeggning och slutfoervar foer anvaent kaernbraensle, Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Lind, Carl; Johansson, Sven-Erik (Nitro Consult AB (Sweden))

    2010-12-15

    This study describes the impact on the surroundings that may occur during rock excavation activities for the final repository for spent nuclear fuel in Laxemar and the encapsulation facility in Simpevarp. The study also includes vibrations created by heavy shipments related to activities at the final repository. The study will provide input to the environmental impact assessment and future design work. The survey area for buildings and facilities covered by the study extends approximately 1,000 metres from the proposed location of the final repository. For the encapsulation facility the survey area has been limited to residential buildings and summer houses within 1,000 metres of the proposed location. In addition, residential buildings along road 743 have been surveyed with regard to the impact of heavy shipments between Laxemar and Faarbo. The results of the surveys and information on planned rock excavation activities have been used to formulate preliminary restrictions and predictions of vibrations and air shock waves from blasting, as well as noise from rock drilling. Predictions have also been made of vibrations from heavy shipments, and a reference survey has been carried out in a residential building near road 743. The predictions of vibrations from blasting rounds reveal low or very low levels. No risk of damage to buildings or equipment is expected. Vibrations from blasting may, however, be perceptible within large parts of the study area, since the human perception threshold for vibration is very low. They will hardly be regarded as disturbing, however. When the accesses to the final repository have been built and rock excavation continues at repository level, the impact on the surroundings is expected to be minimal. The main reason for this is that the blasting will then occur at a depth of about 500 metres, at an ample distance to buildings at surface level. Predictions of air shock waves from blasting rounds indicate low levels. There is no risk of damage but air shocks may be audible at great distances during the first few years when surface facilities are being built and blasting is being done for the ramp and sunk shafts. They are not expected to be perceived as disturbing, since the blasting will be limited to a few times per day during the most intensive period. Structure-borne noise from rock drilling for the repository will not be audible due to large distances to buildings. Noise from above-ground drilling may be audible, but below guideline values. Also, the drilling is limited to a relatively short period of time. In Clab, indoor guideline values may be exceeded during drilling for the encapsulation facility. There is no risk of flyrock from blasting that could cause damage to the surroundings. The scope and nature of flyrock protection will be determined at a later stage, but as a general rule the initial blasting rounds, when the risk of flyrock is the greatest, will be carried out as controlled blasting. Vibrations in surrounding buildings caused by heavy shipments to and from the final repository are not expected to cause any damage, mainly due to the fact that the supporting ground along the transport routes is dominated by rock or till. The reference survey carried out in Oevrahammar verifies this and shows low vibration levels. If the future status of the concerned parts of road 743 is the same as today, disturbing vibrations are unlikely to occur, even if the heavy shipments increase in number. In summary, it is concluded that the guideline values and limit values stipulated in applicable standards, recommendations and guidelines for vibrations, air shock waves and noise from blasting activities, as well as noise from drilling and boring will be met by ample margin. The impact on the surroundings from blasting activities during the construction of the final repository and the encapsulation facility is therefore expected to be very limited

  13. Grate monitoring systems, state of the art; Metoder foer rosteroevervakning, dagslaegesbestaemning

    Energy Technology Data Exchange (ETDEWEB)

    Blom, Elisabet [Aaf Processdesign AB, Linkoeping (Sweden)

    2001-01-01

    During a number of years research and development projects have been made to present methods of monitoring the grate in a grate fired boiler. The monitoring is interesting in order to be able to increase efficiency, increase burn-out of ash, improve the status of emissions, improve transportation of ash and fuel through the furnace, reduce costs for operation and maintenance, handle greater loads etc. Improvement of the combustion has been concentrated to the development of the gas phase combustion. In the past few years the computer development has progressed rapidly and the use of optical monitoring methods have been made possible for monitoring grates. To analyse state of the art of optical grate monitoring systems three different methods have been used, literature search, inquiry where plant owners were asked if they have used grate monitoring systems and if so what experiences they have, and interviews with scientists and users. The inquiry investigation was made during spring 2000 and supplemented with a few known users of grate monitoring systems in august 2000. The interviews were made during august 2000. The methods which have been examined are: Video monitoring; Computer vision; IR-pyrometry; IR-camera technology; Laser measuring methods; Acoustic pyrometry. The survey showed that video monitoring is useful to monitor the fuel bed and an aid to the operators. A good cooling and cleansing system is essential to make the system reliable. If the system is aided with computer vision the computer will show numbers which can be used in the control system. These have been tried at a couple of sites but the system is still being developed and no sites uses this function fully automated. Infrared measurements have been tried in number of research projects. The IR-pyrometer technique is good for measuring temperature but the reliability is too low for some of the users. IR-cameras are used in several waste incineration plants to control the combustion. The systems

  14. Natural refrigerants. Future heat pumps for district heating; Naturliga koeldmedier. Framtida vaermepumpar foer fjaerrvaerme

    Energy Technology Data Exchange (ETDEWEB)

    Ingvarsson, Paul; Steen Ronnermark, Ingela [Fortum Teknik och Miljoe AB, Stockholm (Sweden); Eriksson, Marcus [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Chemical Engineering and Environmental Science

    2004-01-01

    International work on refrigerants is aiming at phasing out HFC. The solution might be natural refrigerants. Within 15-20 years, when present heat pumps for district heating in Sweden are likely not in service any longer, it might still be good economy to install new heat pumps since only the machines need to be replaced. This report describes the possibilities to use natural refrigerants. A first screening resulted in further study on some hydrocarbons, ammonia and carbon dioxide. Water was considered to require too large volumes. In present plants it is practically not possible to use any natural refrigerants, partly because the compressors are not adapted. In new plants the situation is different. Today it is technically possible to install new heat pumps in the studied size, 15 MW{sub th}, using ammonia or hydrocarbons as refrigerant. But likely it is very difficult to get permits from authorities since the refrigerants are toxic or highly flammable. There is substantial international research on using carbon dioxide, and this refrigerant is also used in some applications. Carbon dioxide is used at high pressure and in a trans-critical process. Surprisingly, it turned out that one compressor manufacturer considers it possible to supply a heat pump for district heating within 5 years. This development has taken place in Russia, mainly for domestic use. Thus, within 15 to 20 years there will probably exist a technique where carbon dioxide is used. However, more development is needed. Additionally, low district heating return temperatures are also needed to get an acceptable COP. The investment cost for a heat pump installation is considered to be approx. 30 % higher when using ammonia or propane compared to using R134a. When using carbon dioxide there is in the longer run potential to get lower cost than for R134a. The COPs are almost identical if the systems are properly designed. In the carbon dioxide case the COP is somewhat lower, but has a potential for

  15. Description of Euro codes for concrete constructions; Beskrivning av Eurokoder foer betongkonstruktioner

    Energy Technology Data Exchange (ETDEWEB)

    Westerberg, Bo (Bo Westerberg Konsult AB, Stockholm (Sweden))

    2010-12-15

    Eurocodes, which are common European standards for design of structures for buildings and facilities, prepared by the European Standardisation Committee (CEN) and is published in Sweden by the Swedish Institute for Standards (SIS). Sweden, like the other CEN-member countries, is in the process of replacing their national dimensioning rules with Eurocodes. In an ongoing investigative work on requirements for design, analysis and control of concrete structures with a focus on reactor containment SSM wants to clarify what is needed to ensure mechanical integrity of these structures. The study will form the basis for the development of draft rules for concrete structures. The project aimed to provide SSM factual basis for his valuation of the Eurocode applicability of the Swedish nuclear power plants. The report describes the Eurocodes relating to design of concrete structures. These are: EN 1990: Basis of structural design; EN 1991: Actions on structures; EN 1992: Design of concrete structures; EN 1993: Design of steel structures; EN 1994: Design of composite steel and concrete structures; and, EN 1998: Design of structures for earthquake resistance

  16. Pretreatment of different waste streams for improvement in biogas production; Foerbehandlingsteknikers betydelse foer oekat biogasutbyte

    Energy Technology Data Exchange (ETDEWEB)

    Sarvari Horvath, Ilona (Hoegskolan i Boraas (Sweden)); del Pilar Castillo, Maria (JTI (Sweden)); Loren, Anders; Brive, Lena; Ekendahl, Susanne; Nordman, Roger (SP, Boraas (Sweden)); Kanerot, Mija (Boraas Energi och Miljoe AB (Sweden))

    2010-07-01

    plant was calculated. We have calculated the changes that occur if a pretreatment step was included in the process. For the calculations data obtained during anaerobic digestion of paper waste treated by steam explosion were used. The results showed that while the methane production is increasing by 7,5 % the energy need of the process is decreasing by 21% when a pretreatment step by steam explosion is used instead of a hygienisation step. Batch anaerobic digestion gives methane yields and breakdown rates on pretreated and untreated material, which then can be compared, while continuous anaerobic digestion experiments enable evaluation of the long-term effects of the pretreatment. During the continuous anaerobic digestion experiments untreated or pretreated paper waste was tested in a co-digestion process with an existing waste mixture from Sobacken's biogas plant. However, it was hard to discern the effects of the treatment because the composition and characteristics of the waste mixture had larger impact on the co-digestion process than the pretreatment of the paper fraction part by itself. Nevertheless, our results of the continuous digestion most interestingly showed that a change in substrate composition can stabilize the digestion process with the effect of a 30 % increase in methane production compared to that of the existing original waste mixture. This raises new specific questions on how the composition of mixed-flows influences the biogas production and on how the structural and chemical characteristics of substrate resources, pretreated or untreated, affect the anaerobic digestion. These questions can be central points in future strategic research within the biological waste management area

  17. Energy Choices. Choices for future technology development; Vaegval Energi. Vaegval foer framtidens teknikutveckling

    Energy Technology Data Exchange (ETDEWEB)

    Billfalk, Lennart; Haegermark, Harald (eds.)

    2009-03-15

    investments will present Swedish industry with a good opportunity to develop new technology and new system solutions. Speed up the permitting processes for plants and energy production and electricity networks. Prepare a long-term plan regarding decisions on strengthening the electricity networks, as well as a time schedule for associated decisions and processes. Furthermore, a joint plan regarding foreign connections should be developed for the Nordic region. Lobby for an EU-wide certificate system for renewable energy. The EU target on renewable energy will result in improved opportunities for Sweden to export electricity, but the certificate system currently in force in Sweden will result in the future surplus in electricity production being paid for by Swedish electricity customers. Carry out an immediate change in legislation to facilitate planning for new nuclear power. This is necessary if Sweden wants to replace electricity production from the two oldest nuclear power plants, which may have to close around 2020- 2025 for financial reasons. Power companies need to plan their investments and the safety authorities need to make their preparations. Since other existing nuclear power plants will be decommissioned on a relatively frequent basis in the period 2035-2045, there are even more reasons to keep open the option of new nuclear power. Invest heavily in Sweden in research, development, demonstration and implementation of new technology and systems in several areas. Swedish companies and universities should continue their investments in the area of CCS (capture and storage of carbon dioxide). This is necessary in order for it to be possible to evaluate the consequences of the technology for Sweden and its usefulness and safety in the longer term. A breakthrough is envisaged after 2020 and will in the first instance concern CCS at power stations, but CCS may also be applied to large point sources of carbon dioxide emissions from energy intensive industry. Formulate a

  18. Policy Instruments for an Increased Supply of Energy Crops; Styrmedel foer ett utoekat utbud av biobraensle

    Energy Technology Data Exchange (ETDEWEB)

    Stenkvist, Maria; Widmark, Annika; Wiklund, Sven-Erik; Liljeblad, Anna

    2009-05-15

    crops within the power and heat sector 1. Financing of practical research and development of the logistics chain including harvesting, bundling, compression, preparation, feeding in (to the power plant), storage and transportation of energy crops 2. Investment support to farmers cultivating energy crops with high investment costs 3. Introduction of a national program for development of regional projects supporting cooperation between actors on the energy crop bio fuel market. 1. Financing of Practical Research and Development of the Logistics Chain To reduce the production costs in order to increase the profitability, support for practical research and development of the logistics chain, which includes harvesting, bundling, compression, preparation, feeding in (to the power plant), storage and transportation of energy crops, is suggested. For the success of practical research, it is important that the research is performed in close cooperation between farmers, entrepreneurs within the logistics chain dealing with harvesting, storage and transport of energy crops and energy companies. One way to achieve such cooperation is that the energy companies take the initiative for common research efforts, since neither the farmers nor the contractors on the market for energy crops normally take part in research projects. Neither do they normally have experience of applying for research funds. Common research efforts are also important to find cost-effective solutions for the entire logistics chain. This means that the financing for the research could be a combination of public support and support from the heat and power sector. 2. Investment Support to Farmers Cultivating Energy Crops with High Investment Costs In order to initially increase the interest in energy crops, contribute to establish a market for production of energy crops and manage high initial investment costs, problem that farmers face at the transition from traditional production of grain to energy crops, a

  19. Operation experiences of landfill gas engines; Motorer foer deponigas - Tillgaenglighet och drifterfarenheter

    Energy Technology Data Exchange (ETDEWEB)

    Dejfors, Charlotte; Grimberger, Goeran [AaF-Energikonsult Stockholm AB (Sweden)

    2000-06-01

    The gas that is obtained from landfilled waste is produced by bacteria that digest organic material in an anaerobic environment. Landfill gas consists mainly of methane, carbon dioxide and water vapour. It may be used either as auxiliary fuel in boilers close to the landfill or to generate electricity by means of a gas engine. Several plants where landfill gas is used in gas engines have had serious problems, a. o. with burned exhaust valves. These problems may occur already after a short period of operation, which influences the profitability. The purposes of the project reported were to collect operational experience in Sweden with engines using landfill gas as fuel, to identify which problems there are and which actions or improvements have been implemented in order to correct for these problems. Today, there are 9 facilities where landfill gas is used to fuel a total of 13 gas engines. In addition, there is an engine in Goeteborg which has scarcely been in operation after its installation because there is not enough gas. Contact has been taken with all these facilities. Many have pointed out that the gas engines are sensitive in the vicinity of maximum load, where the control system requires an even gas flow and a stable composition of the gas. A counter-measure in the facilities is to avoid running the engine at full load. All engines are equipped with a lean-NO{sub x} system in order to minimise NO{sub x} emissions. Many have remarked that the lean-NO{sub x} system shuts the engine off when emissions exceed the allowed limits. There is a consensus that spark plugs and ignition cables have created operational problems. These have been changed more frequently than originally expected. Another problem, which has caused operational problems and a need for maintenance, is deposits mainly in the combustion chamber, in valves and cylinder heads. Deposits and high exhaust gas temperature have led to burnt exhaust gas valves and cylinder heads on half of the engines

  20. Legislation of combustion of recovered bio fuels; Regelverk foer eldning av returtraeflis

    Energy Technology Data Exchange (ETDEWEB)

    Harnevie, Henrik; Olvstam, Marie Louise [SwedPower AB, Stockholm (Sweden)

    2001-03-01

    compared to the present levels for these plants. Both the environmental problems (air emissions and quality of ash) as well as the operational problems are, as mentioned above, caused by the fuel contamination. Inadequately sorted wood waste can contain metal objects, which among other problems can lead to blocking of grates or nozzles of fluid bed boilers. Even well classified wood waste contains contaminants such as wood preservatives (mainly As, Cr, Cu), paint (Pb, Zn, Cu, Ti and other metals) and adhesives (mainly nitrogen). However, classification can only be used to remove these contaminants to some extent. The quality can be improved by removal of the fine fraction containing a higher amount of metals than the larger fuel particles. Also crushed gypsum, sand etc are discharged with this fine fraction decreasing the levels of sulphur and silicon. However, contaminants derived from wood preservatives are not enriched in the fine fraction and are therefore difficult to remove by pre-treatments such as classification. Those remaining contaminants have to be handled within the furnace. This project indicates for example that the ratio between zinc, lead, sulphur, chloride and alkali influences corrosion and fouling. The restrictions on air emissions have to be solved with cleaning equipment. The result of this study also indicates that the recirculation of ash to the forest does not seem to be possible without a large amount of efforts and measures. The conclusions from this first step of the research programme are that further knowledge is needed concerning the following items; * Which quality restrictions have to be set on different fuels in order to meet present and future emission limits as well as standards for reprocessing and quality assurance. * The mechanisms for the formation of ash deposits. * The chemical processes of the combustion that occurs in the furnace as well as the significance of the interactions between the contents of zinc, lead, chloride, sulphur

  1. Impurities in biogas - validation of analytical methods for siloxanes; Foeroreningar i biogas - validering av analysmetodik foer siloxaner

    Energy Technology Data Exchange (ETDEWEB)

    Arrhenius, Karine; Magnusson, Bertil; Sahlin, Eskil [SP Technical Research Institute of Sweden, Boraas (Sweden)

    2011-11-15

    Biogas produced from digester or landfill contains impurities which can be harmful for component that will be in contact with the biogas during its utilization. Among these, the siloxanes are often mentioned. During combustion, siloxanes are converted to silicon dioxide which accumulates on the heated surfaces in combustion equipment. Silicon dioxide is a solid compound and will remain in the engine and cause damages. Consequently, it is necessary to develop methods for the accurate determination of these compounds in biogases. In the first part of this report, a method for analysis of siloxanes in biogases was validated. The sampling was performed directly at the plant by drawing a small volume of biogas onto an adsorbent tube under a short period of time. These tubes were subsequently sent to the laboratory for analysis. The purpose of method validation is to demonstrate that the established method is fit for the purpose. This means that the method, as used by the laboratory generating the data, will provide data that meets a set of criteria concerning precision and accuracy. At the end, the uncertainty of the method was calculated. In the second part of this report, the validated method was applied to real samples collected in waste water treatment plants, co-digestion plants and plants digesting other wastes (agriculture waste). Results are presented at the end of this report. As expected, the biogases from waste water treatment plants contained largely higher concentrations of siloxanes than biogases from co-digestion plants and plants digesting agriculture wastes. The concentration of siloxanes in upgraded biogas regardless of which feedstock was digested and which upgrading technique was used was low.

  2. Recommendations for conversions of grate fired boilers to fluidising beds; Anvisningar foer konvertering av rosterpannor till fluidiserad baeddteknik

    Energy Technology Data Exchange (ETDEWEB)

    Eriksson, Lars; Ingman, Rolf [AaF Energikonsult AB, Stockholm (Sweden)

    2001-03-01

    This report gives advice and recommendations for retrofitting of grate fired boilers to fluidising beds. Nine plants have been visited and experiences from these conversion projects have been gathered and analysed. Among the important points planning, fuel specification, heat balance calculations and clarifying of delivery limits can be mentioned. It is also important not to underestimate the need for education of the operational staff.

  3. Evaluation of pine bark for treatment of water from biomass fueled plants; Utvaerdering av bark foer rening av vatten vid biobraensleeldade anlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Hansson, Christina; Hansson, Helen; Hansson, Soeren [Carl Bro Energikonsult AB, Malmoe (Sweden)

    2004-01-01

    In Sweden, large amounts of pine bark are produced as a by-product from the pulp and forest industry. This makes pine bark available in large volumes to a relative low price. Pine bark has shown good absorption effect for organics pollutants, such as oil, in water and pine bark is used commercially as an oil absorbent. In a study the pine bark has also shown to have good absorption effects on heavy metals in water, in laboratory conditions. This indicates that pine bark also could be used as a natural absorbent for heavy metals in flue gas condensate and for leachate from biomass fuel storage. For the latter purpose the bark could be used as a combined heavy metal and oil absorber. In this project the pine barks ability to absorb heavy metals from flue gas condensate has been studied. The tests were performed using an untreated flue gas condensate, which was purified by using a basket filter with commercially available pine bark (trademark EcoBark) as absorbent. The bark filter has the same function as a tube reactor, which would imply that the absorption of heavy metals should be better than the laboratory tests. However, the results from the flue gas condensate tests showed much lower absorption of heavy metals than the laboratory tests. The only significant absorption levels were found for iron and mercury, which showed a reduction ratio of about 25 %. Other metals, such as lead, cadmium, copper, nickel, vanadium and zinc had a reduction ratio of about 10 %, which is quite low compared to the 98 % reduction for lead and about 80 % for copper and zinc that was achieved in the former laboratory tests. The most probable reason that the pine bark had a very low absorbent effect in the flue gas condensate is that the concentration of potassium and calcium restrains the ion exchange capacity of the pine bark. It is also likely that iron mainly is absorbed by the bark, while other metals only are separated as particles. Another possible reason for the rather poor absorption results in the flue gas condensate tests could be that iron affects the absorption of other metals. The water temperature could also have some influence on the results while the laboratory tests were performed at a considerably lower water temperature, 22 C. The flue gas condensate tests also included measurements of COD upstream and downstream the bark filter. The analyses shows that the COD concentration in the condensate upstream the filter is very low, 20-25 mg/litre, while the COD concentration downstream the filter is considerably higher, in the range 40 - 220 mg/litre. The COD before the filter probably originates from the small amount of char particles in the flue gas condensate and the increase of COD after the bark filter comes from humus that has been dissolved from the bark. The heavy metal absorption that has been analysed in the test with flue gas condensate should be comparable with heavy metal absorption from leachate from bio fuel storage, even if the water temperature in the latter case is lower.

  4. Evaluation of electrochemical techniques for measurement of fireside corrosion in thermal power plants; Utvaerdering av elektrokemiska tekniker foer maetning av roekgassidig hoegtemperaturkorrosion i pannor

    Energy Technology Data Exchange (ETDEWEB)

    Hjorrnhede, Anders

    2007-12-15

    The possibility to measure the corrosion rate on-line, in situ, is getting more and more interesting due to increased corrosion. The worsening may be a result of lower fuel quality or increased steam data due to raised efficiency demands. Also the use of inhibitors can be improved and the lifetime of important components can be increased. Today, virtually all corrosion measurements of materials used for waterwalls, superheaters, economisers and other heat-transferring surfaces are based on in-situ probe tests of coupons or rings. The aim of the project is to evaluate the practicability of commercial or semicommercial on-line in-situ corrosion probes for use in waste fired boilers. The target groups are owners of boilers, operators, service personnel but also boiler manufacturer and material producers. Since the use of on-line, in situ, corrosion probes is substantial, some of the most promising corrosion probes have been tested in a waste fired boiler in Hamburg, Germany. Tests in waste fired boiler have never before been performed. The MECO CB, a Linear Polarisation Resistance (LPR) corrosion probe from Coresto Oy, Finland was tested and from Lehrstuhl fuer Umweltverfahrenstechnik und Anlagentechnik (LUAT) der Universitaet Duisburg-Essen, Germany an Electrochemical Noise (EN) - probe was tested. From Pepperl + Fuchs both EN- and LPR-CorrTran corrosion sensors were tested. The test periods were lasting from 1050h to 3750h. The test materials were the low alloyed steel 15Mo3, the Ni-based super alloys Sanicro 63 and Haynes Hastelloy C-2000. The fluegas temperatures were 635 deg C or 520 deg C. The material temperatures were 440 deg C, 420 deg, 350 deg C and was swept from 400 deg C to 300 deg C. All probes are measuring a signal which has a correlation to the corrosion process, but the quantification procedure is not working well. The results achieved from the corrosion probes must be calibrated against corrosion rates measured by means of conventional corrosion probes in order to determine the exact corrosion rate. However, a correlation between the temperature and the corrosion rate exists. The practical use of the on-line corrosion probes is in use together with conventional corrosion probes. Either should the quality of the measured corrosion rates given from the corrosion probes increase or the post treatment of the data must be standardised in order to avoid different kind of influences on the results

  5. The effect of cleaning on materials wastage in biomass and waste fired power plants; Sotningens inverkan paa materialfoerluster foer bio- och avfallseldade pannor

    Energy Technology Data Exchange (ETDEWEB)

    Hjoernhede, Anders; Henderson, Pamela

    2006-03-15

    The reason for this study is the relatively large material loss caused by soot blowing of heat exchange surface in waste- and biomass fired boilers. The material losses depend on the method of cleaning: Normally soot blowing with a relatively high pressure is used in order to remove deposits on super heater tubes. However, this also damages the tube material. Earlier theories state that the material losses are caused by erosion or rather erosion-corrosion of the tube surface. There is a clear evidence for the existence for this type of damage, but it is often caused by badly adjusted soot blowing equipment. However, even well adjusted equipment causes accelerated metal loss, albeit lower than with badly adjusted soot blowers. This type of material loss is caused by the removal of the outer molten deposit layer. This outer layer of deposit actually acts as a barrier to corrosive species diffusing inwards towards the oxide and uncorroded metal. There is a lamellar oxide under this deposit, which is especially protective if it contains Cr{sub 2}O{sub 3}, MoO{sub 3} or Nb{sub 2}O{sub 5}. The lamellar oxide is damaged by the defects produced by the soot blowing and the diffusion of corrosive species into the metal tube. Since molybdenum probably through molybdenum oxide seems to reduce metal losses due to soot blowing, alloys containing molybdenum should be used. The addition of sulphur, or sulphur compounds like ammonium sulphate reduces the deposit growth rate by about 50%. This means that the soot blowing frequency and therefore metal losses are reduced. There is also an indication that certain metals or alloys reduce the tendency for deposits to stick to tubes. Coating with pure nickel is one example of this, but as nickel is sensitive to soot blowing it is not possible to use nickel in areas affected by soot blowing. A common way of reducing metal losses is to mount tube shields on the most affected tubes. These shields are changed regularly. Normally expensive austenitic stainless steels have been used. Cheaper materials like SiCromAl could be used instead. Research indicates that it is beneficial to leave some deposits on the tube, i.e. not to clean completely. A reduction in the soot blowing pressure or frequency also reduces metal losses.

  6. Process for increased biogas production and energy efficient hygienisation of sludge; Process foer oekad biogasproduktion och energieffektiv hygienisering av slam

    Energy Technology Data Exchange (ETDEWEB)

    Rogstrand, Gustav; Olsson, Henrik; Andersson Chan, Anneli; Johansson, Niklas; Edstroem, Mats

    2012-07-01

    In Sweden there is a need to increase biogas production to meet the rising demand for biomethane as vehicle fuel but the amount of domestically available biomass to digest is limited. One way to help meet current and future demand for methane is to enhance the digestion of the substrates that are currently utilized. Vaexjoe municipality in southern Sweden is in the process of upgrading their facilities for biogas production at the Sundet waste water treatment plant. Their aim is to produce more biogas in order to meet the demand from an increasing methane-based local transit fleet. This is the backdrop to a joint project between JTI and Vaexjoe municipality where JTI's mobile pilot plant was used to study the possibility of extracting more biogas from the existing sewage sludge. In the future, Vaexjoe municipality also plans to co-digest source separated municipal organics with the sewage sludge, which will likely result in stricter demands in terms of hygienization of all utilized substrates. The goal of the project at hand was to demonstrate the possibility to produce more than enough additional biogas from existing sewage sludge to yield a net energy profit even with the added energy demand of ensuring the hygienic quality of the digestate through conventional pasteurization. Although the project was focused on the conditions at Sundet waste water treatment plant, the issues dealt with are general and the results are relevant to many waste water treatment plants in Sweden. The research, conducted between June 2011 and January 2012 were divided into two trials. The two trials, described schematically in Figure 1, represented two possible process configurations designed to reach the goal stated above. The key component of both process configurations is the addition of a post-digestion step to the existing single-step digestion process. In trial 1 the additional feature of dewatering between the two digestion steps served to reduce energy demand for pasteurization

  7. The pulverization and handling of soft plastics for energy recovery; Soenderdelning och hantering av mjuka plaster foer energiutvinning

    Energy Technology Data Exchange (ETDEWEB)

    Wiklund, Sven-Erik

    2000-10-01

    The purpose of the project has primarily been to investigate suitable equipment (mills, crushers, shredders) for the pulverization of different types of soft plastics from the agricultural sector (large sacks and silage plastic) and the peat extraction industry (plastic covers) with the aim of being able to use the plastic material as fuel in conventional solid waste-fired plants. Many of the mills that are used for pulverizing different types of biofuel have proved not to be particularly suitable for soft plastics. The project has comprised the following: * Contact with a number of plant owners with different types of plants (grate, CFB and BFB boilers) for a review of existing fuel handling and fuel feed equipment as well as the demands they make on the fuel that is to be fired. * Contact with Trio Plast concerning previous tests carried out in connection with the collection, baling, handling, pulverization and combustion of plastics from the agricultural sector. * Contact with mill suppliers for participation in the tests and for feedback on experience gained in connection with the pulverization of soft plastics. * Choice of a suitable plant for practical trials based on contact with the above plant owners as a reference group. * Practical trials in 5 mills with the pulverization of soft plastics from agriculture (silage plastic and large sacks) as well as plastic from peat extraction (plastic covers) and * Evaluation of technical, economic, energy-related and environmental preconditions. Following contact with several owners of solid waste-fired combustion plants, and after hearing their opinions, it became clear that many of them were doubtful about the combustion of plastic. They are primarily afraid of tripping superheaters, etc. Consequently, two plants without superheaters, one in Oestersund and the other in Malmoe, were chosen for the tests. The mills that were tested were: * A SIM mill from WahIkvist, Oedeshoeg Plant - a mobile slow-action pulverizer for

  8. District heating for increased biogas production. Technical and economical evaluation of district heating as heating source in biogas processes; Fjaerrvaerme foer utoekad biogasproduktion. Teknisk och ekonomisk utvaerdering av fjaerrvaerme foer uppvaermning av biogasprocesser

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Per (AaF-Consult AB, Stockholm (Sweden))

    2009-11-15

    This report presents a technical evaluation, the potential and an economical evaluation of the increased net biogas production by using district heating as energy supply for different types of biogas production units. The study presents generalized results for different plant sizes. The district heating is considered as replacement of the heat produced by burning biogas in a hot-water boiler. Hence more biogas could be available for upgrading to fuel-gas quality to be used in vehicles as a renewable fuel. The study is aimed at biogas producers, district heating and combined heat and power (CHP) companies. Biogas has a composition of mostly methane (about 65 %) and carbon dioxide (about 35 %) and small amounts of other gases e.g. sulphur dioxide (H{sub 2}S). Biogas up-grading is a process where the methane content is increased to about 97 % by removing most of the other gases in e.g. an absorption unit. The Swedish biogas is mainly produced in several sewage treatment plants and some co-digestion units but is also collected from dumps. Biogas is produced by anaerobic microorganisms at temperatures of about 36 and 55 deg C which correspond to the thermal optimum for mesophile and thermophile bacteria respectively. Co-digestion of animal material which e.g. is contained in collected organic household waste has to be pasteurized at 70 deg C for 1h according to EU-regulations. Such regulations may also be introduced to the sludge from municipal sewage treatment plants. Due to the fact that the process temperature is higher than the temperature of the substrate (sludge or organic waste material) as well as the outdoor temperature, both heating of the incoming substrate and compensation of heat losses are required. Traditionally most of the biogas has been burnt to generate the necessary heat for the process and premises at the plant. The excess gas has been burnt in a torch. In recent years the biogas produced in Sweden has found increased use as a renewable vehicle fuel

  9. Critical factors for profitable combined production of heat, power and biofuels; Kritiska faktorer foer loensam produktion i bioenergikombinat

    Energy Technology Data Exchange (ETDEWEB)

    Nohlgren, Ingrid; Gunnarsson, Emma; Lundqvist, Per; Stigander, Haakan; Widmark, Annika (AaF, Stockholm (Sweden))

    2012-02-15

    During the last 5-10 years, research and development efforts have been made in the field of polygeneration of heat and power with production of 'other green' products such as transport fuels or wood pellets. The driving force for heat and power producers is the potential of increased profitability through additional sales of heat. The driving force for wood pellet and some transport fuel producers is the potential of low cost process steam or heat. However, in the case of gasification based transport fuel production processes the situation is different. The process generates a surplus of heat, which can benefit from the proximity of a district heating net. In addition, some polygeneration combinations could provide other advantages such as more efficient raw material handling. Together with these driving forces, the EU renewable energy directive (which targets 10 % renewable energy use in the transport sector by 2020), shows that the market for production of renewable transport fuel is expanding. To refine Swedish biomass resources to more highly valuable products such as wood pellets or renewable transport fuels would maintain industry and employment opportunities within Sweden and at the same time fulfils the international and national climate targets. The overall aim with this project is to describe the factors which are crucial for the opportunity for profitable polygeneration of heat, power and wood pellets or renewable transport fuels and how these factors influence the location of such a plant within Sweden. The important factors can be categorized as: (1) Supply of raw material, (2) distribution of raw material and products, (3) Demand of products and (4) Integration between the different plants. In this project, only general aspects are described and should be seen as guidance for the industry (both energy and forest industry) which has an interest in polygeneration. The project gives an overview of different possibilities, opportunities and

  10. Site selection - location of the repository for spent nuclear fuel; Platsval - lokalisering av slutfoervaret foer anvaent kaernbraensle

    Energy Technology Data Exchange (ETDEWEB)

    2010-12-15

    This document describes the localization work and SKB's choice of site for the repository. Furthermore, SKB's basis and rationale for the decisions taken during the work are reported. The document is Appendix PV of applications under the Nuclear Activities Act and the Environmental Code to both build and operate an encapsulation plant adjacent to the central interim storage facility for spent nuclear fuel in Oskarshamn, and to construct and operate a disposal facility for spent nuclear fuel at Forsmark in Oesthammar municipality

  11. Process for increased biogas production and energy efficient hygienisation of sludge; Process foer oekad biogasproduktion och energieffektiv hygienisering av slam

    Energy Technology Data Exchange (ETDEWEB)

    Rogstrand, Gustav; Olsson, Henrik; Andersson Chan, Anneli; Johansson, Niklas; Edstroem, Mats

    2012-07-01

    In Sweden there is a need to increase biogas production to meet the rising demand for biomethane as vehicle fuel but the amount of domestically available biomass to digest is limited. One way to help meet current and future demand for methane is to enhance the digestion of the substrates that are currently utilized. Vaexjoe municipality in southern Sweden is in the process of upgrading their facilities for biogas production at the Sundet waste water treatment plant. Their aim is to produce more biogas in order to meet the demand from an increasing methane-based local transit fleet. This is the backdrop to a joint project between JTI and Vaexjoe municipality where JTI's mobile pilot plant was used to study the possibility of extracting more biogas from the existing sewage sludge. In the future, Vaexjoe municipality also plans to co-digest source separated municipal organics with the sewage sludge, which will likely result in stricter demands in terms of hygienization of all utilized substrates. The goal of the project at hand was to demonstrate the possibility to produce more than enough additional biogas from existing sewage sludge to yield a net energy profit even with the added energy demand of ensuring the hygienic quality of the digestate through conventional pasteurization. Although the project was focused on the conditions at Sundet waste water treatment plant, the issues dealt with are general and the results are relevant to many waste water treatment plants in Sweden. The research, conducted between June 2011 and January 2012 were divided into two trials. The two trials, described schematically in Figure 1, represented two possible process configurations designed to reach the goal stated above. The key component of both process configurations is the addition of a post-digestion step to the existing single-step digestion process. In trial 1 the additional feature of dewatering between the two digestion steps served to reduce energy demand for

  12. Additive for reducing operational problems in waste fired grate boilers; Additiv foer att minska driftproblem vid rostfoerbraenning av avfall

    Energy Technology Data Exchange (ETDEWEB)

    Gyllenhammar, Marianne; Herstad Svaerd, Solvie; Davidsson, Kent; Hermansson, Sven; Liske, Jesper; Larsson, Erik; Jonsson, Torbjoern; Zhao, Dongmei

    2013-09-01

    The combustion of waste implies a risk for deposits and corrosion in different parts of the combustion facility. In recent years, research and tests have been performed in order to find ways to mitigate these problems in waste-fired plants. Most waste-fired plants in Sweden are grates whereas most of the research has been carried out in fluidized bed plants. The purpose of this project is to examine whether co-firing of sewage sludge and waste can reduce deposition and corrosion also in grate-fired boilers as has been shown in fludised beds. The objective is to determine the deposit growth and its composition as well as describing the initial corrosion attack. Representing sulphur-rich waste, elementary sulphur is also added to the waste and thereby compared with sludge as an additive. The target groups for this project are plant owners, researchers, consultants and authorities. Tests were performed in a 15 MWth waste-fired boiler with moving grate at Gaerstadverket, Tekniska Verken (Linkoeping). The boiler produces saturated steam of 17 bars and 207 deg C, and the normal fuel mixture contains of household and industry waste. The results show that co-firing with as heigh as 20 weight-% SLF (25 energy-%) was possible from an operational point of view, but the deposit rate increased especially at the two warmest positions. Generally the deposit rate was highest in the position closest to the boiler and decreased further downstream. During the tests a lot higher amount of SLF than normal was used (recommended mix is 5-10 % of SLF) this to be able to see effects of the different measures. Up to 23 weight-% of the rather moist sewage sludge was possible to fire when co-firing waste and SLF, without addition of oil. By adding sludge the deposit rate decreased but the increase upon adding SLF to ordinary waste was not totally eliminated. In the tests 'Avfall and SLF' the deposits were rich in chlorine. High concentrations of metal chlorides were found in the

  13. Dose conversion factors for radiation doses at normal operation discharges. F. Methods report; Dosomraekningsfaktorer foer normaldriftutslaepp. F. Metodrapport

    Energy Technology Data Exchange (ETDEWEB)

    Bergstroem, Ulla; Hallberg, Bengt; Karlsson, Sara

    2001-10-01

    A study has been performed in order to develop and extend existing models for dose estimations at emissions of radioactive substances from nuclear facilities in Sweden. This report gives a review of the different exposure pathways that have been considered in the study. Radioecological data that should be used in calculations of radiation doses are based on the actual situation at the nuclear sites. Dose factors for children have been split in different age groups. The exposure pathways have been carefully re-examined, like the radioecological data; leading to some new pathways (e.g. doses from consumption of forest berries, mushrooms and game) for cesium and strontium. Carbon 14 was given a special treatment by using a model for uptake of carbon by growing plants. For exposure from aquatic emissions, a simplification was done by focussing on the territory for fish species, since consumption of fish is the most important pathway.

  14. Process and sensor diagnostic: Data reconciliation for a flue gas channel; Process- och sensordiagnostik: Dataaaterfoerening foer ett roekgastaag

    Energy Technology Data Exchange (ETDEWEB)

    Karlsson, Christer; Dahlquist, Erik [Maelardalen Univ., Vaesteraas (Sweden). Dept. of Public Technology

    2003-10-01

    The project has shown that model-based data reconciliation can be used in heat and power plants, but it needs support of soft sensors. Generally power plants are not equipped with more sensors than required by control systems, environment and financial reports. Soft sensors are needed to compensate for lack of redundancy in mass-flow sensors. Redundancy makes it possible to isolate gross errors. The smallest error needed to be determined sets the requirement on the process model accuracy. Tools available today from this project are; classification of different process sections with redundancy analysis and gross error detection. Quantification of the errors with the mass balance model has not been successful and this part needs further development. Theoretical comparison of the three different methods presented resulted in favour of data reconciliation based on a mass balance model. The mass balance model has a structure based on physical reality. The searches for gross errors are transparent to the user. It can handle sensor failure. The statistical linear model is preferred for smaller process sections when transparency is not needed and focus is on fast, simple and cheap implementation. Data reconciliation based on steady-state energy balance has the same origin as the mass balance model. Data reconciliation based on energy balance is harder to compute and its sensors difficult to classify. The drawback is complexity, but the strength is that the large number of temperature sensors can be used in the data reconciliation. Large gross errors are detected and quantified for most process mass flows with acceptable accuracy. Performances for small errors are not as good. Performance of the data reconciliation is strongly dependent on precision in the process models. This conclusion is drawn from comparison with other studies that show good performance for laboratory simulations. There are still many parts to develop further as: Soft sensors, tests for identification

  15. Silicon carbide based sensor system for minimized emissions in flue gases; Kiselkarbidbaserat sensorsystem foer minimering av emissioner i roekgaser

    Energy Technology Data Exchange (ETDEWEB)

    Lloyd Spetz, Anita; Bjorklund, Robert

    2012-02-15

    Control of the combustion process is necessary in order to operate boilers in an economic and environmentally acceptable manner. Large power plants can afford expensive measurement instruments to continuously monitor the composition of flue gas. Smaller facilities often lack complete gas analysis systems and it would be to their advantage to have access to inexpensive measurement equipment which could be installed at several points in the flue gas channel. Since oxygen concentration is such an important parameter for describing the combustion process the lambdasond is currently being used as an oxygen sensor in flue gas. It has the advantage of usage for more than 30 years in the automobile industry. Experience from that application has aided its introduction in the power industry. Conditions are not the same in the two branches but the lambdasond is an established technology, produced in large volume, widely available and inexpensive. Vehicle manufacturers continue to develop sensor technology and monitoring capabilities have been extended to CO, NOx and NH3. The latter is the result of SCR (selective catalytic reduction) of NOx by addition of NH3 (from urea), which has been introduced as an exhaust gas aftertreatment technology in diesel powered vehicles. The power industry can be expected to follow this trend by incorporating sensors for monitoring and control of SCR and SNCR (non-catalytic selective reduction) in flue gas applications. This report describes evaluation of silicon carbide based transistors, which have previously been studied in diesel exhaust gas and small boiler flue gas, for applications in larger power plants

  16. Feasibility study - Lowered bed temperature in Fluidised Bed boilers for waste; Foerstudie - Saenkt baeddtemperatur i FB-pannor foer avfallsfoerbraenning

    Energy Technology Data Exchange (ETDEWEB)

    Niklasson, Fredrik

    2009-01-15

    Waste incineration generally serves two purposes; 1) dispose of waste and 2) generation of heat and power. In the process of power production from waste fuels, the steam temperatures in super heaters are generally limited by the severe fouling and corrosion that occurs at elevated material temperatures, caused by high concentrations of alkali metals and chloride in the flue gas and fly ash. The overall aim of a continuation of present project is to determine if a reduced temperature of the bed zone in a fluidized bed waste incinerator reduces the amount of alkali chlorides in the flue gas. If so, a reduced bed temperature might enable increased steam temperature in super heaters, or, at unchanged steam temperature, improve the lifespan of the super heaters. The results from the project are of interest for plant owners wishing to improve performance of existing plants. The results may also be used to modify the design of future plants by boiler manufacturers. The aim of present pre-study was to determine how far the bed temperature can be reduced in a waste fired fluidized bed boiler in Boraas while maintaining a stable operation with sufficient combustion temperature in the freeboard to fulfil the directives of waste incineration. A continuation of the project will be based on the results from present study. The work is based on experiments at the test boiler. During the present study, no other measurements were performed apart from some sampling of bed material and ashes at different modes of operation. The experiments show that it is possible to alter the air and recycled flue gas in such a manner that the bed temperature is reduced from about 870 deg C to 700 deg C at 100% load and normal fuel mixture, while fulfilling the directive of 850 deg C at 2 seconds. Within normal variations of the fuel properties, however, the bed temperature increases to somewhat above 700 deg C if the fuel turns dry, while it falls below 650 deg C when the fuel turns wet. With

  17. Function of all-metal separators for waste fuels. Phase 1; Funktion av allmetallseparatorer foer avfallsbraenslen. Etapp 1

    Energy Technology Data Exchange (ETDEWEB)

    Jacoby, Juergen; Wrangensten, Lars

    2004-08-01

    Various waste incineration facilities, which use different types of waste fuels, have difficulties with a high content of non-magnetic metal, especially aluminum in their fuels. Aluminum may melt on the grate and can lead to corrosion or fouling in the furnace. Additionally, a high content of aluminum in the flyash may cause difficulties in terms of storage or further use of the ash as e.g. construction material. The industrial demand for efficient separators for non-magnetic metals from a fuel stream is rather large. There is however some uncertainty in the performance and efficiency of metal separators. Two types of separators can be found, the first type is called eddy current separator, the other type is based upon a metal detector with a sorting unit in the form of a chute or similar afterwards. An eddy current separator consists of a fast rotating drum containing several permanent magnets with alternating polarity. Due to the rotation, the change in the magnetic field induces eddy currents in conducting materials. The eddy currents cause a force in non-magnetic metal, the Lorentz force, which repels the material away from the rotating drum while all other material follows the systems flow direction. Systems equipped with a metal detector activate a mechanical sorting device, separate chute or air nozzles, when a metal particle is detected. In contrast to eddy current separators all types of metals can be detected and sorted out by systems based on metal detector. Several technical solutions for metal separation supplied by various manufacturers are described in the report. The companies have been asked to supply product information on the working principle, technical data, efficiency and limits for different types of metals. Two reference power plants have been visited and their experiences with all-metal separators are described. Haendeloeverket in Norrkoeping uses eddy current separators for separation of non-magnetic metals from household waste

  18. Treatment of biofuel ashes for forest recycling; Behandling av aska fraan biobraenslen foer spridning paa skogsmark - etapp 1

    Energy Technology Data Exchange (ETDEWEB)

    Bjurstroem, H.; Sjoeblom, R. [AaF-Energikonsult, Stockholm (Sweden)

    1997-03-01

    Logging residues are the easiest available fuel for an increased production of energy in Sweden from renewable sources. A consequence of their removal from the forest is that the cycle of mineral nutrients is broken. The purpose of recycling the ash after this fuel to forest land is to compensate for the removal and close again the nutrient cycle. Recycling nutrients and returning the inorganic components of the biomass removed from the forest should be performed in accordance with general principles of environmental protection, health considerations and the good house-keeping of natural resources. The activities should also be carried out in accordance with the needs of the forest and energy plant owners regarding good technology and economy. This implies that functional requirements originating from these principles and needs should be clearly structured and formulated and that such requirements should provide a basis for the continued development work as well as for the implementation of suitable, economical and efficient systems. Returning inorganic constituents implies that the principle of recirculation is followed as well as that nutrients are brought back which improves accretion in the forest. At the same time, the risk of damage to the forest can be assessed as insignificant. Furthermore the risks to human health are also assessed to be insignificant provided that pertinent precautions are taken to avoid dusting. In the present report, technical and economical aspects of importance for the selection of method as well as for the establishment of a system are described and discussed. The need for further development work is identified in the following areas: functional requirements - operational requirements, sampling, testing and quality assurance, granulation, curing processes and drying/sintering. 102 refs, 1 fig, 2 tabs

  19. Bio-oils and other bio fuels used in heat- and power generation; Flytande biobraenslen foer el- och vaermeproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Sandgren, Annamaria; Ekdahl, Emma; Sernhed, Kerstin; Lindstroem, Erica

    2010-05-15

    The purpose of this study was to assemble and disseminate knowledge about bio-oils and other bio fuels which are used for heat- and power generation or liquid bio fuels/oils that may become interesting in the future. One aim of this study was to give an updated picture of the Swedish market for bio-oils and to provide an overview of practical experience on the usage of bio-oils in the Swedish heat and power industry. In order to show a green profile, bio-oils can be used in the heat and power generation. However, not all bio-oils can be viewed as climate friendly. Some production of bio-oils may actually - if a lifecycle perspective is considered - lead to increased emissions of greenhouse gases, and there are also ethical issues that need to be considered. The data collection was carried out in three different fields. The objective of the first part was to create an overview of the Swedish market for liquid bio fuels/oils for heat and power production. The second part of the study aimed to clarify the issues surrounding environmental and ethical issues associated with the use of different bio-oils. A selection of oil crops for a closer study was made based on production volume (soybean, palm oil and rapeseed) and expected future potential (jatropha). This part of the study was based on a literature review. In the third part of the study technical and practical experiences from using bio-oils in heat and power production were studied. The interviews made with purchasing managers in the second part gave valuable information on which utilities would be the most interesting to interview for the study of technical and practical experiences, where interviews were carried out with persons familiar with the daily operation of the plant. The use of liquid bio fuels was about 4.3 % of total fuel use in Swedish district heating production in 2007 (1.2 % pine oil and 3.0 % other bio-oil). In other words, it is mainly bio-oils that have been used and not other types of liquid

  20. Bio-oils and other bio fuels used in heat- and power generation; Flytande biobraenslen foer el- och vaermeproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Sandgren, Annamaria; Ekdahl, Emma; Sernhed, Kerstin; Lindstroem, Erica

    2010-05-15

    The purpose of this study was to assemble and disseminate knowledge about bio-oils and other bio fuels which are used for heat- and power generation or liquid bio fuels/oils that may become interesting in the future. One aim of this study was to give an updated picture of the Swedish market for bio-oils and to provide an overview of practical experience on the usage of bio-oils in the Swedish heat and power industry. In order to show a green profile, bio-oils can be used in the heat and power generation. However, not all bio-oils can be viewed as climate friendly. Some production of bio-oils may actually - if a lifecycle perspective is considered - lead to increased emissions of greenhouse gases, and there are also ethical issues that need to be considered. The data collection was carried out in three different fields. The objective of the first part was to create an overview of the Swedish market for liquid bio fuels/oils for heat and power production. The second part of the study aimed to clarify the issues surrounding environmental and ethical issues associated with the use of different bio-oils. A selection of oil crops for a closer study was made based on production volume (soybean, palm oil and rapeseed) and expected future potential (jatropha). This part of the study was based on a literature review. In the third part of the study technical and practical experiences from using bio-oils in heat and power production were studied. The interviews made with purchasing managers in the second part gave valuable information on which utilities would be the most interesting to interview for the study of technical and practical experiences, where interviews were carried out with persons familiar with the daily operation of the plant. The use of liquid bio fuels was about 4.3 % of total fuel use in Swedish district heating production in 2007 (1.2 % pine oil and 3.0 % other bio-oil). In other words, it is mainly bio-oils that have been used and not other types of liquid

  1. National responsibility in an enlarged European Union?; Nationellt ansvar foer anvaent kaernbraensle i en utvidgad Europeisk Union?

    Energy Technology Data Exchange (ETDEWEB)

    Cramer, Per; Stendahl, Sara; Erhag, Thomas [Dept. of Law, School of Business, Economics and Law, Goeteborg Univ. (Sweden)

    2007-04-15

    The principle of national responsibility has two sides: One about how Sweden takes responsibility for the wastes that arise in the country from nuclear power generation. The other side about the rights Sweden considers itself to have to prevent that spent nuclear fuel from other countries are disposed or stored in Sweden. The last aspect of the principle has been regulated in an explicit law against final waste disposal and intermediate storage of foreign spent nuclear fuel in Sweden. The question about how Sweden will take responsibility for the spent nuclear fuel that arises within the country is not regulated in law in a corresponding way. It can be argued that such a discrepancy in interpretation of the principle does not favour its legal strength. On the multilateral level, the question is regulated through the Non-proliferation treaty from 1970 and the convention about the safety in handling spent nuclear fuel and radioactive wastes that were added within the framework of IAEA 1997. Non-proliferation confirms the right of all States to develop a national civilian nuclear power industry and within the framework of this right lies also the competence to decide about the policy for the back end of the nuclear fuel cycle. That is to say, the States have, according to the agreement, the freedom to apply a principle about exclusive national responsibility for managing the spent nuclear fuel and the radioactive wastes, as is clearly confirmed in the IAEA-convention. It should however be noted that the IAEA, since the beginning of the 1990s, has initiated several studies concerning the legal, political and the physical conditions for establishing multinational plants for intermediate storage or final waste disposal of spent nuclear fuel or high-level nuclear wastes. In reports a series arguments been presented which speaks for such a development. At the core of these arguments is the interest of winning economic and technological scale advantages, and the non

  2. System and market study of bio-methane (SNG) from bio fuels; System- och marknadsstudie foer biometan (SNG) fraan biobraenslen

    Energy Technology Data Exchange (ETDEWEB)

    Valleskog, Martin (CMV Konsult (Sweden)); Marbe, Aasa; Colmsjoe, Linda (Grontmij AB (Sweden))

    2008-07-01

    current Swedish tax system. From a production standpoint, the industrial and automotive markets are best suited as recipients of SNG because demand is evenly distributed throughout the year, CHP and heat market at least favorable as it is heavily dependent on the variation of the heat demand during the year. By contrast, the biggest economic advantage is achieved when SNG is replacing natural gas and oil for heating. Secondly, in the sectors of power generation and vehicle fuel SNG is favored by subsidies. High electricity certificate prices and high power generation efficiency benefit SNG for cogeneration. The analysis of the current competitive situation leads to SNG require some form of financial support to become a commercially available energy resource. The fastest establishment of SNG facilities will be realized in which the natural gas network already established, as it gives access to the entire natural gas market. Industrial and automotive market has been steady demand over the year and can therefore form the basis for the draft instruments. Politically speaking, there is great interest to find renewable alternatives in the automotive market. If we are to invest in a new cogeneration installation is the most economical to gasify biofuel combustion the gas in a gas turbine with subsequent steam cycle (BIGCC). This is far more economical than to first convert the gas to SNG and then burn it in a combined natural gas plant. It requires, however, that the values on electricity certificate is relatively high, or that prices are high

  3. Environmental guidelines for reuse of ash in civil engineering applications - phase 2; Miljoeriktlinjer foer askanvaendning i anlaeggningsbyggande - etapp 2

    Energy Technology Data Exchange (ETDEWEB)

    Bendz, David; Wik, Ola; Elert, Mark; Haakansson, Karsten

    2006-07-15

    difficult to determine. The health risk associated with intake of vegetables and accidentally oral intake are crucial. In both cases arsenic sets the limits. Model calculations indicate that fluoride constitute only an insignificant risk.. Chloride and sulfate in ashes may, depending on the construction, constitute a certain risk with respect to the drinking water quality in a local well. The comparison between the calculated guideline values and the ash data that was available showed that the majority of the ashes could be used in a road construction without implying a significant risk to health or environment. In the available set of ash data, each combination of incineration plant and fuel is only represented by few data. This makes it difficult to draw specific conclusions for a certain type of ash.. The model or framework for developing the general guidelines, presented herein, may also be used for site specific environmental risk assessments. If so, the model should be further developed to better describe the risk for exposure by dust.

  4. Evaluation of the Swedish biogas standard - basis for a future audit; Utvaerdering av svensk biogasstandard - underlag foer en framtida revision

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Mattias

    2011-04-15

    This report is intended to constitute a basis for a future revision of the SS 15 54 38, 'Motor fuels - Biogas as fuel for high-speed otto engines.' When it was published in 1999, it was not deemed appropriate to source compressed biomethane from landfill gas, because of its wider range of trace elements, often in relatively high concentrations, such as siloxanes and halogenated hydrocarbons. Siloxanes are also present in the gas from waste water treatment plants, but the assessment was made that upgrading methods available at the time reduced these levels sufficiently. By putting a maximum limit on the nitrogen content, landfill gas was effectively shut out. Technical Development (cryogenic upgrading making it possible to clean landfill gas to biomethane quality; stricter emissions standards for vehicles that has led to a higher level of sophistication in engine and aftertreatment technologies) has now made it necessary to better control the levels of all trace elements. The state of standardization is not satisfactory for CNG in general and renewable CNG (biomethane) in particular. Standardization at the international level is mostly qualitative. Most standards are at the national level and with the exception of Sweden biomethane is only standardized for injection on the natural gas network. A mandate (M/475, 2010) from the European Commission to develop the CEN standards for biomethane fed into the grid, or used directly as renewable CNG, may change this, and the issue will be addressed in a new committee (CEN/TC408 'Project Committee - Biogas for use in transportation and injection into natural gas pipelines'). A variety of trace elements has been discussed for inclusion in the new standards, where countries such as Holland and France stand out as supporters of more stringent and comprehensive regulations. This report's working group considers it like the regulation of substances such as siloxanes and halogenated hydrocarbons will lead

  5. The EU system for emissions trading after year 2012; EU:s system foer handel med utslaeppsraetter efter 2012

    Energy Technology Data Exchange (ETDEWEB)

    Normand, Mathias; Mjureke, David (eds.)

    2007-01-15

    biofuel streams in combustion installations that partly use biofuels should be abolished. Sweden should press for a broad and harmonised definition of the term 'combustion installation', bearing in mind the possible consequences for small installations. Efforts should be made to encourage auction procedures as the basis of allowance allocation for all sectors within the Scheme. However, until competitors outside the EU encounter some form of cost in connection with their carbon dioxide emissions, industry covered by the Scheme can continue to be allocated free allowances, preferably according to benchmarks common to the entire EU. The electricity and district heating sectors within the EU should not be allocated free allowances. These sectors' allowances should be distributed to the market by means of auctions that are open to all parties within the EU ETS. New entrants of the electricity and district heating sectors should be required to purchase their allowances on the market. Until auction procedures are introduced for existing industrial participants in the scheme, new entrants in the industrial sector should be allocated free allowances in accordance with common EU benchmarks where possible. Any surpluses from reserves kept for new entrants should be cancelled. If reserves are maintained for free allocation to new entrants, allocation of allowances to plants that have closed should cease.

  6. Instruction manual: Fly ash stabilised sludge (FSS) as liner material; Vaegledning: Flygaskastabiliserat avloppsslam (FSA) som taetskikt

    Energy Technology Data Exchange (ETDEWEB)

    Carling, Maria; Haakansson, Karsten; Macsik, Josef; Mossakowska, Agnes; Rogbeck, Yvonne

    2007-06-15

    Several old waste sites are on the verge to be closed up during the next ten years. The function of a liner is to limit the amount of water that is infiltrated to the waste. This leads to high demand on a liner's permeability, shear strength and durability. Several pilot studies have been followed up where fly ash stabilised sewage sludge (FSS) was used as liner. The results show that FSS has low hydraulic conductivity (low permeability) and that it meets the demands put on a liner for non-hazardous wastes. Closure with FSS as liner puts special demands on the materials, the mixing action and during installation. The aim of this instruction manual is that it will work as an aid to manufacture and install liner, based on fly ash and sewage sludge, which fulfils functional demands. The manual contains a description of geotechnical and environmental demands to accomplish. This includes the following; manufacturing, storing, installation and follow up/control. This instruction manual is aimed for those who are planning closures of a landfill with FSS and need guidance to plan, carry out and control the liner construction. The manual can also be used by environmental agencies in order to control that the closure is done appropriately. Sewage sludge and fly ash from different producers can have varying properties. The quality of the used materials can change the FSS mixture's material properties and thereby also its permeability and durability. Both raw materials and mixtures should thereby be investigated according to material parameters. The mixtures dry solid content is a critical parameter as both shear strength and handling properties will be effected. In order to acquire sufficient amount of raw material storing is often required. Several aspects must then be counted on, as the properties of the raw materials can be altered. Manufacturing FSS must be done with the same material properties that have been investigated and evaluated in laboratory. Different mixing methods can installation strategies perform well. The weather is an important factor during mixing and installation. It is also of importance due to work environment (ammoniac release to the air and dusting conditions). Beside quality control of the raw materials and the mixture it is also recommended to verify permeability during field conditions. The knowledge and engagement of the staff is of great importance in order to fulfil requirements.

  7. High-temperature pretreatment of biogas substrate by using district heating to increase the biogas production; Hoegtemperaturfoerbehandling av biogassubstrat med fjaerrvaerme foer oekad biogasproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Del Pilar Castillo, Maria; Ascue, Johnny [JTI, Uppsala (Sweden); Olsson, Marcus; Henriksson, Gunilla; Nordman, Roger [SP, Boraas (Sweden)

    2011-12-15

    In this study, we have shown that pre-heating sludge from a waste water treatment plant can give a higher biogas production rate. However, pretreatment showed no effect on substrate from a biogas plant at the conditions tested in this study. The study has also shown that there is potential of using district heating in the biogas industry for thermal pretreatment of sludge.

  8. Repository for spent nuclear fuel. Preliminary construction description - layout D Oskarshamn the Simpevarp area; Slutfoervar foer anvaent kaernbraensle. Preliminaer anlaeggningsbeskrivning - layout D. Oskarshamn, delomraade Simpevarp

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-02-15

    This report presents the preliminary design of a repository located in the Simpevarp area. The description has been disposed so as to deal primarily with the site dependent layouts for the above- and underground constructions. The report is disposed as follows: c1 gives the background and some basic information. Chapter 2 presents the demands and necessary conditions that take precedence when adapting the plant to the local conditions, construction, operation and closure. Chapter 3 is a general description of the area, its infrastructure and the specific sites that have been studied. Chapter 4-5 describe the design of the plant for the two chosen sites. Chapter 6 gives a review of data for the plant, and Chapter 7 'References' is the last part of the main document. The appendices A-I give brief information on the general, non-site specific, parts of the plant, e.g. buildings, life cycle, system, operation and organization.

  9. Dose conversion factors of radiation doses at normal operation discharges. E. Description of geographical surroundings and critical group; Dosomraekningsfaktorer foer normaldriftutslaepp. E. Omraadesbeskrivningar och kritisk grupp

    Energy Technology Data Exchange (ETDEWEB)

    Hallberg, Bengt

    2001-10-01

    A study was performed in order to develop and supplement existing models for calculating radiation doses from discharges of radionuclides under normal operating conditions at the Swedish NPPs at Barsebaeck, Forsmark, Oskarshamn and Ringhals, and at the nuclear plants at Studsvik and the Westinghouse Atom fuel plant. A general description of the surroundings of each plant is given in this report, together with an inventory of agricultural activities, forestry, areas for leisure activities etc. The conditions of the critical group has been selected based on the description of the surroundings and the modeling of dispersion in the atmosphere and fallout on the ground. In contrast to earlier models where fictive critical groups were used, the present model is based on factual circumstances.

  10. Analysis of algorithms for detection of resonance frequencies in vibration measurements on super heater tubes; Analys av algoritmer foer detektering av resonansfrekvenser i vibrationsmaetningar paa oeverhettartuber

    Energy Technology Data Exchange (ETDEWEB)

    Eriksson, Daniel

    2010-07-01

    Combustion of fuel in thermal power plants emits particles which creates coatings on the super heater tubes. The coatings isolate the tubes and impairs the efficiency of the heat transfer. Cleaning the tubes occurs while the power plant is running but without any knowledge of the actual coating. A change in frequency corresponds to a change in mass of the coatings. This thesis has been focusing in estimating resonance frequencies in vibration measurements made by strain gauges on the tubes. To improve the estimations a target tracking algorithm had been added. The results indicates that it is possible to estimate the resonance frequencies but the algorithms need to be verified on more signals.

  11. Stable control in FB-boilers. Guidelines for improved control of head fans; Stabilare drift hos FB-pannor. Riktlinjer foer foerbaettrad reglering av huvudflaektar

    Energy Technology Data Exchange (ETDEWEB)

    Boman, Katarina; Hedlund, Johan

    2007-12-15

    The general aim is to present research that allows more stable performance in FB-boilers that cause decreased emissions of CO and NO{sub x}, less alarms caused of transient course of events. The primary goal for the project was to clarify how the control of air and flue-gas fans influence on operation stability and how control parameters shall be adjusted for optimized operation. Furthermore it should be clarified whether it is recommended to recirculate flue gas from pressure- or suction side of the flue gas fan. The target group is plant owners with plants that show periodic oscillations that cannot be related to fuel variations. The report can also be used as a support for new and rebuilding. Three plants has been visited and studied considering physical construction of recirculation of flue gas and also for control of air supply. One of the plants was studied more in detail and tests were performed to find the dynamics in components such as fans, dampers and control system. A computerized control model was build for this plant and verified the operation. Then the model was optimized to improve the operation of the plant. The results from the simulations shows that it is possible to build simulation models that correspond well with the real plant operation. Simulations also show that it is possible to optimize the operation of the plant by optimization tests in the simulation model. It is also shown that the constructions of recirculate flue gas from the suction side of the flue gas fan introduce disturbance in the primary air flow which give large consequences in the O2 control which introduce other control oscillations. The simulations also show that more even flow of primary gas flow, evens out the combustion and less oscillations is raised. One recommendation is therefore at new or rebuilding that the recirculation of flue gas is taken at the pressure side of the flue gas fan and that the control of the flow will be subordinated the primary airflow. If the

  12. Load Prediction in District Heating Systems with Regard to Scenarios and Uncertainties in Weather; Lastprognoser foer fjaerrvaerme med haensyn till scenarier och osaekerheter i vaedret

    Energy Technology Data Exchange (ETDEWEB)

    Hedberg, Martin; Koppers, Gijs [Meteopolaris AB, Nacka (Sweden)

    2011-11-15

    The report shows, by means of load calculations on ensemble weather forecasts and subsequent production planning, that by a better optimization of the operation of district heating plants the costs of production of heat and electricity can be reduced. During a fifth of the time the saving potential is 5% or more.

  13. Abatement Technologies for Volatile Organic Compounds in Emissions from Biofuel Driers; Reningsteknik foer organiska aemnen i utslaepp till luft vid biobraensletorkning

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, Karin; Ehrstedt, Thomas [Sycon Energikonsult AB, Malmoe (Sweden)

    2000-06-01

    This report is a part of a program at Vaermeforsk called Drying of Biofuels and deals with abatement technologies for volatile organic compounds (VOC) in biofuel drier emissions. The report gives an account of the amount of organic matter in wood and in drying gases and also of different abatement technologies for VOC. Processes from about 20 contractors are briefly described. The conclusions from this work are that thermal or catalytic oxidizing technologies in connection with regenerative heat recovery seems to be the most suitable technique for this application. Both technologies should give a degree of purification above 95 %. The purification cost for a typical case has been estimated to about 22 SEK per kg removed organic matter in both cases. The investment cost is higher for the catalytic oxidizer (6-20 MSEK for a 60.000 Nm{sup 3} /h catalytic plant compared to 4-6,5 MSEK for a thermal plant) but the fuel cost is lower. Condensation is a usable technique but it suffers from bad degree of purification. By using a wet electrostatic precipitator (WESP) the degree of purification can be enhanced but it will still be lower than for the oxidizers. Adsorption and absorption are not suitable for gases at high temperatures containing several different organic compounds at low concentrations, which is the case in biofuel drying. This means high purification costs and low degree of purification. Other technologies that have been found less suitable are biological purification and membrane technology. World-wide there are a few reference plants based on thermal oxidizing in connection with biofuel drying. Otherwise the experiences are very limited. According to this, tests in pilot plant scale are recommended before investment in a full-scale plant for biofuel driers.

  14. Tools for system validation. Dynamic modelling of the direct condenser at Sandvik II in Vaexjoe; Hjaelpmedel foer systemvalidering. Dynamisk modellering av direktkondensorn paa Sandvik II i Vaexjoe

    Energy Technology Data Exchange (ETDEWEB)

    Raaberg, Martin [Dynasim AB, Lund (Sweden); Tuszynski, Jan [Sycon Energikonsult AB, Malmoe (Sweden)

    2002-04-01

    The project reported here aimed to test the suitability of existing computer tools for modelling of energy processes. The suggested use for the models are at the early tests and validations of new, refurbished or modernised thermal plants. The technique presented in this report should be applicable for clarification of the scope of delivery and testing for both the process and tile control system. The validation process can thus be simplified, allowing risk reduction and predictability of the commissioning. The main delays and economical misfortune often occurs during commissioning. This report should prove the feasibility of the purchase routines where purchaser, vendor and quality inspection will use a common model of the process to validate system requirements and specifications. Later on it is used to validate structure and predefine testing. Thanks to agreement on the common model, early tests can be conducted on complex systems, minimizing the investment risks. The modelling reported here concerns the direct condenser at Sandvik 11, power and heating plant owned by Vaexjoe Energi AB in Sweden. We have chosen the direct condenser because it is an existing, well-documented and well-defined subsystem of high complexity in both structure and operation. Heavy transients made commissioning and test runs of similar condensers throughout Sweden costly and troublesome. The work resulted in an open, general, and physically correct model. The model can easily be re-dimensioned through physical parameters of common use. The control system modelled corresponds to the actual control system at the Sandvik II plant. Any improvement or deep validation of the controllers was not included in this work. The suitability is shown through four simulation cases. Three cases are based on a registered plant operation during a turbine trip. The first test case uses present plant data, the second an old steam valve actuator and the third uses the old actuator and an error in level

  15. After Chernobyl. Consequences for energy policy, nuclear safety, radiation protection and environment protection. Efter Tjernobyl. Konsekvenser foer energipolitik, kaernsaekerhet, straalskydd och miljoeskydd

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    The basic problems of the safety of nuclear power have been elucidated. The cause of the Chernobyl accident and its effects are discussed. The impact of this accident on the evaluation of Swedish nuclear safety is dealt with, and recommendations concerning increased safety when nuclear power accidents take place in other countries are presented. The environmental and economic consequences of early decommissioning of the Barsebaeck power plant are discussed as well as the general aspects of nuclear power phaseout in Sweden.

  16. Evaluation of Co-Digestion of Biosludge from Pulp and Paper Mills; Utvaerdering av samroetningspotential foer bioslam fraan massa-/pappersbruk

    Energy Technology Data Exchange (ETDEWEB)

    Berg, Andreas; Karlsson, Anna; Ejlertsson, Joergen; Nilsson, Fredrik

    2011-02-15

    The biogas potentials from 2 biosludges from the pulp- and paper industry and 10 possible co-digestion substrates have been evaluated. 6 combinations, each including two co-digestion substrates and one biosludge, were evaluated in lab scale biogas reactors. Stable biogas processes were obtained with all combinations and the rawgas potential was higher in the co-digestion processes then for the biosludges alone (0.31- 0.43 compared to 0.21- 0.22 NL/g VS) The investment costs for two production plants were calculated. For a plant using 7 ton biosludge TS/d (total solids per day), co-digested with evaporation condensate (3 m3/d) and fibre sludge (3 ton/d) and thereby producing 850 000 Nm3 CH{sub 4}/yr the investment cost was estimated to 43 MSEK excluding ground works. For a larger plant using 20 ton biosludge TS/d, co-digested with food waste (8 ton/d) and cereal residues (12 ton/d) and producing 2 500 000 Nm3 CH{sub 4}/yr, the investment cost was estimated to 51 MSEK excluding ground works

  17. Pre-treatment of waste fuel with low-speed shredding and screening for fluidized bed incineration; Foerbehandling av avfallsbraensle foer fluidbaeddpannor med laangsamtgaaende valskross och saekerhetssiktning

    Energy Technology Data Exchange (ETDEWEB)

    Hermansson, Sven; Victoren, Anders; Niklasson, Fredrik; Jones, Frida

    2013-09-01

    In FB combustion of waste, an important cost factor is the pre-treatment of the waste fuel. The most common method of final levigation of the waste fuel is using hammer mills, which crushes the fuel with high force and high rotational speed. The advantage of the powerful hammer mill is, however, also a disadvantage. The fraction of fines becomes large, and the method is experienced to cause high maintenance costs and problems with accidental fires. A plausible alternative to the hammer mill is the shredder. The rotational speed of the shreeder is lower, while it cutting and slicing the waste fuel instead of grinding it. The shredder is, therefore, expected to yield less wear and tear, lower electricity consumption and less accidental fires. On the other hand, the shreeder may yield a higher fraction of oversized fuel particles, which could cause problems in the combustion, especially in smaller FB-plants with one single fuel supply conveyor. In this project, the framing of question has been if low-speed shredding in combination with screening of over sizes fuel particles, may function for smaller FB plants with one single fuel supplying conveyor. The aim of the project has been to support FB plant owners and manufacturers for independent comparision of the different fuel pre-treatment methods, via pre-treatment and combustions trials and economical comparisons. The concept of lowspeed shreddning and screening has been compared economically with a traditional hammer mill system and a shredding system designed for a larger FB plant. Moreover, combustion trials have been carried out with shredded and screened fuel, and hammer milled fuel, in two smaller parallel FB furnaces with one single fuel supplying conveyor per furnace. The fuels were analysed for particle size distribution and composition, and the operation during the combustion trial was evaluated. The economical evaluation of the new pre-treatment concept, with lowspeed shredding and screening, yielded an

  18. Survey of development work and problems with different collection techniques of food waste; Kartlaeggning av utvecklingsarbete samt problem vid olika insamlingstekniker foer matavfall

    Energy Technology Data Exchange (ETDEWEB)

    Henriksson, Gunilla

    2010-07-01

    In accordance with Sweden's environmental objectives it has been decided that, by 2010, 35 per cent of all food waste shall be recovered through biological treatment. In order to get there, the problems regarding collection methods needs to be solved. There are several different collection systems to choose between, but at the present time there is no complete list of the methods and techniques available on the market. Lists of advantages and disadvantages with each system, of potential improvements, and of completed or ongoing development projects are also missing, and creating difficulties for municipalities and businesses which are planning on introducing a system. The goal with this study is to provide a survey of technical problems with different systems and to identify previous studies as well as new innovations within collection techniques. The expectation is that this work eventually will lead to improved collection systems. The study will cover existing collection techniques in households, large-scale kitchens, restaurants and grocery stores in Sweden. The study will only cover the so called hard parameters, i.e. primarily technical issues. The target group is on the one hand municipalities planning on starting collection of food waste and on the other hand all actors in the area, such as innovators, producers and suppliers as well as Waste Refinery's organizations. Soft issues such as issues regarding information and quality are not included. The system limits of this project span between the recycling equipment of homes and businesses to the food waste's treatment at the biological treatment plant. The methods that have been used in this project are: questionnaire survey to 133 municipalities that today are recycling food waste, telephone interviews with a number of biological treatment plants and innovators in the business, and Internet searching for relevant reports and studies in the field. The results show that the paper bag and the

  19. Harvest and logistics for better profitability from small cultivations of Short Rotation Willow Coppice; Skoerdeteknik och logistik foer baettre loensamhet fraan smaa odlingar av Salix

    Energy Technology Data Exchange (ETDEWEB)

    Baky, Andras; Forsberg, Maya; Rosenqvist, Haakan; Jonsson, Nils; Sundberg, Martin

    2010-06-15

    In Sweden, the political desire to increase the amount of short rotation willow coppice (Salix) plantations has been expressed. However, for various reasons interest from farmers has been low. The hypothesis of this study is that the total area of Salix cultivation can be increased by also cultivating fields smaller than those generally considered economic today. In order to lower production costs, machine systems adapted for harvest of smaller fields are required. The possibility of using farmers' existing tractors and more convenient machines, as well as achieving lower machine costs for smaller fields, may increase farmers' interest. The long-term objective is to achieve large-scale deliveries of willow with small-scale solutions at farm level, as an option and complement to today's more large-scale systems for harvesting willow. Costs, energy use and climatic impact (CO{sub 2} emissions) for two harvest and logistical chains suitable for small fields have been calculated from field to energy plant, and methods for minimizing these costs have been analyzed. Comparison is made with the direct chipping system, the most commonly used in Sweden today. The systems studied comprised: 1. Direct bundling harvest system with a tractor-towed harvester, collection of bundles in the field with a trailer-mounted crane, and storage in a pile before delivery. Chipping is performed at the energy plant. 2. Direct billeting with a tractor-towed harvester accompanied simultaneously by a tractor and trailer for collection, and storage in a pile before delivery. 3. Direct chipping with a self-propelled modified forage harvester accompanied simultaneously by a tractor and container for collection, and direct delivery to plant. Both the billet and bundle systems show higher costs than the direct chipping system, irrespective of field size. The analysis of different scenarios and conditions shows possibilities of lowering the costs through certain measures. Furthermore

  20. High temperature corrosion in biomass- and waste fired boilers. A status report; Kunskapslaeget betraeffande hoegtemperaturkorrosion i aangpannor foer biobraensle och avfall

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, P; Ifwer, K; Staalenheim, A; Montgomery, M; Hoegberg, J; Hjoernhede, A

    2006-12-15

    Many biomass- or waste-fired plants have problems with high temperature corrosion on the furnace walls or at the superheaters, especially if the steam temperature is greater than 500 deg C. An increase in the combustion of waste fuels means that an increasing number of boilers have had problems. Therefore, there is great interest from plant owners to reduce the costs associated with high temperature corrosion. At the same time there exists a considerable driving force towards improving the electrical efficiency of a plant by the use of more advanced steam data. The purpose of the work presented here was to answer three main questions: What can be done to reduce high temperature corrosion with current fuel blends and steam temperatures? How can more waste fuels be burnt without an increased risk for corrosion? What needs to be done to reach higher steam temperatures in the future? The level of knowledge of high temperature corrosion in biomass- and waste-fired boilers has been described and summarised. The following measures are recommended to reduce corrosion in existing plant: Make sure that the fuel is well mixed and improve fuel feeding to obtain a more even spread of the fuel over the cross-section of the boiler. Use combustion technology methods to stabilize the oxygen content of the flue gases near the membrane walls and other heat transfer surfaces. Experiment with additives and/or supplementary fuels which contain sulphur in some form, for example peat. Reduce the flue gas temperature at the superheaters. Review soot-blowing procedures or protect heat transfer surfaces from soot blowers. Evaluate coated membrane wall panels in parts of the furnace that experience the worst corrosion. Test more highly alloyed steels suitable for superheaters and when replacing a superheater change to a more highly alloyed steel. For the future, the following should be considered: The role of sulphur needs to be investigated more and other additives should be investigated

  1. Characterization of solid heterogeneous waste fuel - the effect of sampling and preparation method; Karaktaerisering av fasta inhomogena avfallsbraenslen - inverkan av metoder foer provtagning och provberedning

    Energy Technology Data Exchange (ETDEWEB)

    Wikstroem-Blomqvist, Evalena; Franke, Jolanta; Johansson, Ingvar

    2007-12-15

    The aim of the project is to evaluate the possibilities to simplify the methods used during sampling and laboratory preparation of heterogeneous waste materials. Existing methods for solid fuel material is summarized and evaluated in the project. As a result of the project two new simplified methods, one for field sampling and one for laboratory preparation work has been suggested. One large challenge regarding waste sampling is to achieve a representative sample due to the considerable heterogeneity of the material. How do you perform a sampling campaign that will give rise to representative results without too large costs? The single largest important source of error is the sampling procedure, equivalent to about 80% of the total error. Meanwhile the sample reduction and laboratory work only represents 15 % and 5 % respectively. Thus, to minimize the total error it is very important that the sampling is well planned in a testing program. In the end a very small analytical sample (1 gram) should reflected a large heterogeneous sample population of 1000 of tons. In this project two sampling campaigns, the fall of 2006 and early winter 2007, were conducted at the waste power plant Renova in Gothenburg, Sweden. The first campaign consisted of three different sample sizes with different number of sub-samples. One reference sample (50 tons and 48 sub-samples), two samples consisting of 16 tons and 8 sub-samples and finally two 4 tons consisting of 2 sub-samples each. During the second sampling campaign, four additional 4 ton samples were taken to repeat and thus evaluate the simplified sampling method. This project concludes that the simplified sampling methods only consisting of two sub-samples and a total sample volume of 4 tons give rise to results with as good quality and precision is the more complicated methods tested. Moreover the results from the two sampling campaigns generated equivalent results. The preparation methods used in the laboratory can as well be

  2. Oxidation catalysts for cleaning of CO and TOC in flue gases - step 1; Oxidationskatalysatorer foer rening av ofoerbraenda roekgaser - etapp 1

    Energy Technology Data Exchange (ETDEWEB)

    Berg, Magnus [TPS Termiska Processer AB, Nykoeping (Sweden); Harnevie, H. [SwedPower AB (Sweden)

    2001-01-01

    Environmental demands on the firing of solid fuels are gradually being sharpened and will in the future be regulated by different EG directives. Of particular importance is an EG directive on the incineration and co-incineration of waste. Most fractions of recycled wood fuel will be included in this directive. In the directive, high demands are placed above all on the restriction of the release of unburned compounds such as CO, TOC and dioxins. In many cases, it will be very difficult to optimise combustion in order to reduce releases of these compounds in question to the level regulated by legislation. This has therefore led to the initiation of this project on oxidation catalysts as a tool in the reduction of such emission components. In this preliminary study, 11 suppliers of oxidation catalysts have been contacted on this issue. An investigation has been carried out into their principles and costs and also interest in the application of these. Of the suppliers interviewed, 7 were seriously interested in the current application and at least 5 can be considered interesting for further discussion at later stages. Based on the information received, it could also be noted that costs for monolithium catalysts which can clean 12.000 m{sup 3}{sub n} flue gas/hour varied between approximately 60.000 and 240.000 SEK. This flow of flue gas corresponds to the amount generated by a 5 MW plant fired with normal forest chips (50% TS). Within the scope of this stage, an application study of two boilers has also been carried out (Vattenfall's boiler at Swedish Match and Marbodal). In both cases, the catalysts are considered to be able to be assembled without much reconstruction. However, it remains uncertain whether the catalysts can endure the current concentration of particles in the flue gas duct or for Swedish Match also the concentration of HCl and SO{sub 2} respectively. Finally is a proposal of how continued work in this area should be carried out described. This

  3. 2D or 3D? New user interfaces for control rooms in process industries. A feasibility study; 2D eller 3D? Nya graenssnitt foer processindustrins kontrollrum

    Energy Technology Data Exchange (ETDEWEB)

    Karlsson, MariAnne

    2008-01-15

    Three dimensional user interfaces and techniques for visualisation have been discussed as possible ways to improve the work situation for control room operators in process industries. The aims of the project, which is a pilot project, has been: (i) to compile existing knowledge on the pro's and con's of 2D versus 3D user interfaces in order to assess and conclude if, and how, 3-dimensional visualisations could be applied when designing new user interfaces for modern process control rooms and (ii) to investigate operators' attitudes towards and acceptance of 3-dimensional user interfaces for visualisation of information. The project has included the following activities: a literature review has been completed in order to collect information on different projects and tests in which 3-dimensional user interfaces have been evaluated for different tasks; an identification of feasible use cases has been made, partly on basis of a workshop in which participated researchers from the field and partly on basis of study visits to different process plants on the west coast of Sweden; an interview study has been carried with control room operators at four different power plants in order to find out the operators' assessments of and attitudes towards 3-dimensional information visualisation; and interviews with representatives of system developers have been completed in order to elicit information on ongoing development work and experiences of developing and implementing 3-dimensional user interfaces in control rooms. On basis of the literature review as well as the interview studies cannot be concluded that 3-dimensional user interfaces and 3-dimensional visualisation of information hold any general advantages compared to 2-dimensional solutions. Pro's and con's are, instead, highly contextual and dependant upon (i) the characteristics of user (in terms e.g. of computer skills); (ii) the (work) task; and (iii) the specific design of the user

  4. Investigation and mapping of the requirements for lifting devices in a nuclear facility; Utredning och kartlaeggning av krav foer lyftanordningar inom kaernteknisk anlaeggning

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Kjell (Inspecta Sweden AB, Vaexjoe (Sweden))

    2010-03-15

    This technical report covers the investigation and identification of requirements for lifting devices in nuclear facilities. The report is divided into the following Section: 1. A mapping of the regulatory framework for nuclear hoists in Finland, Germany and USA. 2. A description of how the international legal framework is applied in for replacement or modernization of lifts in the Swedish nuclear power plants. 3. In Europe, the new harmonized standard has been developed for conventional hoists. The rules appear in the 'EN-13 001'. The study will illustrate these rules, and how they currently apply in the nuclear industry in Sweden. 4. A comparison between the IKH's lifting standards and EN13001 which differences are highlighted and explained

  5. Biodiversity on mire ecosystems and drained peatlands - a basis for environmental peat harvesting; Biologisk maangfald paa myrar och dikad torvmark - underlag foer ett miljoemaessigt torvbruk

    Energy Technology Data Exchange (ETDEWEB)

    Stedingk, Henrik von (Swedish Biodiversity Centre, Uppsala (Sweden))

    2009-07-01

    The interest of peat harvesting has increased, due to the political ambition to reduce greenhouse gas emissions and to increase the use of local energy sources. Peatlands drained for forestry, a common resource in Sweden, can be a good energy source in terms of greenhouse gas emissions, under certain conditions. The question is what consequences increased peat harvesting would have on biodiversity in the forest landscape. To answer this question this literature study was performed to summarize what is known about the life of a natural and drained mire, and to discuss what conservation values could be found on a drained peatland. The definition of mire is a wetland with active peat accumulation, even if mires also are distinguished based on specific plant communities. A mire often contains several mire types. Some mire taxa are specialized for living on mires, other organisms have other main habitats but utilize the mire for fulfilling their life cycle. The level of knowledge varies for different organisms. The best known groups are vascular plants and bryophytes. They are also used for classifying mires since their abundance is related to gradients of pH, fertility and water level. Arthropods is a diverse group on mires favored by open moist forests and water pools. Poor mires with restricted flora may be good insect habitats. Birds are found in habitats rich in insects. Large mires are richer in wader species thanks to higher heterogeneity and a variety of insect habitats. The microscopic life in peat is rich and the species composition differs from the forest soil, even if the level of knowledge is limited. Drainage leads to species turn over for many groups of organisms and drainage often leads to a decrease in diversity. However, drained peatlands is a collective concept including different peatland types in different succession phases and different intensity of drainage. Therefore in general, drained peatlands cannot be treated as less important for

  6. Combustion tests in a solid fuel boiler to clarify the emissions when co-firing refuse; Proveldning i fastbraenslepanna foer att kartlaegga emissioner vid inblandning av olika avfallsfraktioner

    Energy Technology Data Exchange (ETDEWEB)

    Blom, Elisabet; Lundborg, Rickard; Wrangensten, Lars

    2002-04-01

    In this Vaermeforsk-project tests have been performed in a 60 MW moving grate steam boiler at Tekniska Verken in Linkoeping. The boiler plant has an electrostatic filter for dust reduction and also a flue gas condensing plant with heat recovery. Vaermeforsk has financed the project. During the tests the following fuel fractions have been injected into the reference fuel, a mix of recovered wood chips (70 %) and bark (30 %): Paper/plastic/wood fuel (10 % and 25 % injection on an energy basis); Meat powder (10 % and 25 % injection on an energy basis); Napkin waste (10 % injection on an energy basis); Leather waste (10 % injection on an energy basis). The highest lower heating value was noted for meat powder, approx. 24 MJ/kg with a moisture content of 3,4 %. The heating values for the other fuel fractions were on the same level or just beneath the corresponding heating value for the reference fuel. The highest chlorine content was found in the paper/plastic/wood fraction respectively the leather waste fraction with 1,2 and 1,4 % (weight) of chlorine. The meat powder had the highest nitrogen content but all the fuel mixes had a quite high content of nitrogen with values over 1 % (weight). Analyses of sulphur in the fuels showed that leather waste had the lowest content just over 0, 1 %, considered as a low sulphur level for fuels in general. However, there are problems to get balance between in- and output for sulphur and chlorine based on fuel analysis. Difficulties to take representative fuel samples, especially when it comes to chlorine, can be an explanation. Video camera recordings and flue gas analysis in the furnace showed that the injection of refuse fractions seems to improve the combustion conditions with better local combustion of CO and hydrocarbons. The results from the emission measurements in the chimney can be summarised as follows (emission values at 11 % O{sub 2}): the lowest CO emission was noted with 25 % meat powder injection (<50 mg/nm{sup 3

  7. Measurements of emissions during waste wood combustion to identify refurbishment needs; Maetning av emissioner vid foerbraenning av RT-flis foer att identifiera eventuella ombyggnadsaatgaerder

    Energy Technology Data Exchange (ETDEWEB)

    Lindau, Leif

    2003-01-01

    The background to this project is the new EU directive 2000/76/EG regarding incineration of waste. This directive may have an effect on emission limits for Swedish plants firing waste wood. It may lead to needs of refurbishment in e.g. the area of flue gas cleaning equipment. In order to produce a basis to evaluate the need for such upgrading, measurement of metals, HCI, SO{sub 2} , CO, TOC and dioxin have been carried out on three plants firing wood waste: a grate boiler (Handeloeverket P11), one circulating fluid bed boiler (Aaterbruket in Lomma), and a bubbling fluidised bed boiler (Johannes in Gaevle, firing 50% waste wood). The measurements have mainly been carried out after boiler, equivalent to upstream flue gas cleaning. The results are that the demands of the EU directive on most points can be managed with existing equipment if this consists of electrostatic precipitator or bag filter with good performance and flue gas condensor. Without flue gas condensor, there is a need for other measures for 1-10 and for grate boilers, SO{sub 2} as well. The requirements in the directive for TOC is weaker than the demand on CO, and correspondingly, the demand on CO is driving. The level of dioxin from the boiler (upstream filter) exceeds allowed emission, and is in the range of 0,1-2 ng TE/Nm{sup 3} tg, 6 % O{sub 2} . Existing equipment will meet the emission limit for the lower levels (0,1-0,3) , but not safely for the higher levels (1,5-2). Correspondingly, there may be a need for equipment upgrading, e.g. in the form of activated carbon injection upstream flue gas filter.

  8. Wind power on Gabriel mountain - Follow-up of the consequences for reindeer herding, third year results; Vindkraft paa Gabrielsberget - Uppfoeljning av konsekvenserna foer rennaeringen, tredje aarets resultat

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-05-15

    According to the Environmental Court's decision Gabriel Mountain the wind plant's impact on reindeer husbandry followed up by a control program. According to the Environmental Court's decision Gabrielsberget the wind plant's impact on reindeer husbandry followed up by a control program. The control program was initiated in autumn 2008. Reporting to the County Board will be made annually until the trial period ends. The construction of roads on Gabriel Mountains began in November / December 2008. No construction work was carried out, however, during the period that the reindeer were in the area (January-March 2009). The construction work started again in the summer / fall of 2009. The first 20 wind turbines began operating in January 2011. During these periods, the continuous interviews were held with reindeer herders from grazing district Byrkije. Reindeer herding utilization of the area before the wind farm been built and under construction has thus been mapped. Despite good grazing conditions Byrkije experienced difficulty in reindeer herding in and around wind power construction at Gabriel Mountain, especially during the second winter season (2010/11), when construction has been more extensive. Byrkije had to support feeding and use helicopter, something that previous seasons only was done in poor grazing conditions. The herders were also more people who worked actively with the reindeer and the working day has been longer and more strenuous compared to the seasons before the wind farm was built. The reindeer has moved more and were more spread out. The herders have also been forced to retrieve outside reindeer winter Loegdeaa land, something that has rarely happened in previous seasons. The reindeer's movement patterns and utilization of pastures have been different during the construction of the wind farm than in previous years. This report will be based on the new data over the years monitoring program runs.

  9. Biofuels from the forest. A study of environmental impacts and economy of different uses; Biobraensle fraan skogen. En studie av miljoekonsekvenser och ekonomi foer olika anvaendningar

    Energy Technology Data Exchange (ETDEWEB)

    Ekstroem, Clas; Amnell, Goesta; Anheden, Marie; Eidensten, Lars; Kirkegaard, Gunilla [Vattenfall Utveckling AB (Sweden)

    2002-04-01

    in neighbouring countries. In some of these cases, bioenergy would not imply any additional cost in comparison with the use of electricity produced by coal condensing plants. In most other cases the estimated additional costs will not be higher than about 60 SEK/tonne reduced CO{sub 2} emissions (up to 90 SEK/MWh electricity). If bioenergy in cases with additional costs is to replace electricity from coal condensing plants it is necessary to place a price on the CO{sub 2} emissions by coal power stations and/or submit them to carbon dioxide taxation. This is not the case today. Pellet boilers in multi-family houses can utilise considerable amounts of forest biofuel and provide heating at lower costs than electric boilers. District heating and cogeneration of power and district heating can also utilise large volumes of forest biofuel (up to 20 TWh resulting in more than 12 Mtonnes/year reduced CO{sub 2} emissions) at low added costs (about 60 SEK/tonne reduced CO{sub 2} emissions corresponding to 20-40 SEK/MWh district heating) in comparison with fossil alternatives. Emissions of other air pollutants can then more easily be minimised and will occur further from built-up areas. The amount of electricity that can be produced from forest biofuel at these low added costs in comparison with fossil alternatives is restricted by the level of district-heating production. Today the power transmission systems permit only limited exports of electrical power, and consequently important reductions in CO{sub 2} emissions can be achieved at low cost if electricity from biofuel-fired cogeneration plants, that cannot be exported, is used by new heat pumps in villas. This would also give lower emissions of other air pollutants in urban areas than if pellets or oil were used to fire the villa boilers. Heat pumps and pellet boilers will be the most favourable forest biofuel based heating alternative for villas heated by water radiators. Heat pumps give greater reductions in CO{sub 2

  10. Cost studies concerning decontamination and dismantling. The interim store for spent fuel at Studsvik; Kaerntekniska kostnadsstudier avseende dekontaminering och nedlaeggning. Mellanfoervaret foer anvaent kaernbraensle i Studsvik

    Energy Technology Data Exchange (ETDEWEB)

    Sjoeblom, Rolf; Sjoeoe, Cecilia [Tekedo AB, Nykoeping (Sweden); Lindskog, Staffan; Cato, Anna [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)

    2006-04-15

    The interim store for spent fuel at Studsvik was designed and constructed in 1962-64. It has been used for wet storage of fuel from the Aagesta Nuclear Power Plant as well as the R2 reactor at Studsvik. The interim store comprises three cylindrical pools for fuel storage as well as equipment for handling and decontamination. The purpose of the present work is to develop methodology for calculation of future costs for decontamination and dismantling of nuclear research facilities. The analysis is based on information from Studsvik as well as results from information searches. The requirements on precision of cost calculations is high, also at early stages. The reason for this is that the funds are to be collected now but are to be used some time in the future. At the same time they should neither be insufficient nor superfluous. It is apparent from the compilation and analysis that when methodology that has been developed for the purpose of cost calculations for power reactors is applied to research facilities certain drawbacks become apparent, e.g. difficulties to carry out variation analyses. Generally, feedback of data on incurred costs for the purpose of cost calculations can be achieved by using one or more scaling factors together with weighing factors which are established based on e.g. expert judgement. For development and utilisation of such tools it is necessary to have access to estimated costs together with incurred ones. In the report, the following combination of aspects is identified as being of primary significance for achieving a high precision: Calculations with the possibility to calibrate against incurred costs; Radiological surveying tailored to the needs for calculations; Technical planning including selection of techniques to be used; Identification of potential sources for systematic deviations. In the case of the interim store, some of the sources of uncertainty are as follows: Damaged surface layers in the pools; Maintenance status for the

  11. Nuclear cost studies for decontamination and dismantling. The interim storage for spent fuels at Studsvik.; Kaerntekniska kostnadsstudier avseende dekontaminering och nedlaeggning. Mellanfoervaret foer anvaent kaernbraensle (FA) i Studsvik.

    Energy Technology Data Exchange (ETDEWEB)

    Sjoeblom, Rolf; Sjoeoe, Cecilia [Tekedo AB, Nykoeping (Sweden); Lindskog, Staffan; Cato, Anna [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)

    2005-05-01

    The interim store for spent fuel (FA) at Studsvik was designed and constructed in 1962-64. It has been used for wet storage of fuel from the Aagesta Nuclear Power Plant as well as the R2 reactor at Studsvik. FA comprises three cylindrical pools for fuel storage as well as equipment for handling and decontamination. The purpose of the present work is to develop methodology for calculation of future costs for decontamination and dismantling of nuclear research facilities. The analysis is based on information from Studsvik as well as results from information searches. The requirements on precision of cost calculations is high, also at early stages. The reason for this is that the funds are to be collected now but are to be used some time in the future. At the same time they should neither be insufficient nor superfluous. It is apparent from the compilation and analysis that when methodology that has been developed for the purpose of cost calculations for power reactors is applied to research facilities certain drawbacks become apparent, e.g. difficulties to carry out variation analyses. Generally, feedback of data on incurred costs for the purpose of cost calculations can be achieved by using one or more scaling factors together with weighing factors which are established based on e g expert judgement. For development and utilisation of such tools it is necessary to have access to estimated costs together with incurred ones. In the report, the following combination of aspects is identified as being of primary significance for achieving a high precision: Calculations with the possibility to 'calibrate' against incurred costs; Radiological surveying tailored to the needs for calculations; Technical planning including selection of techniques to be used; Identification of potential sources for systematic deviations. In the case of FA, some of the sources of uncertainty are as follows: Damaged surface layers in the pools; Maintenance status for the drains

  12. Retrofitting oil fired boilers for pellets based pulverised wood firing at peak load; Konvertering av befintliga oljepannor till pulvereldning foer spetslast

    Energy Technology Data Exchange (ETDEWEB)

    Malmgren, A.; Tao, L.; Wennstroem, M. [TPS Termiska Processer AB, Nykoeping (Sweden)

    2000-03-01

    The types of equipment for grinding of pellets used by commercial heat producers today are discussed. Powder from a representative number of plants has been collected and classified using a traditional vibrating sieve and an aerodynamic method 'Aeroklass'. The results show clearly that the difference in 'fluffyness' between a powder produced from pellets, briquettes or directly from wood can be identified by the aerodynamic method. The shapes of different particles are shown in microscope pictures. The requirements of burners and combustion chambers for good burnout of fuel particles are discussed theoretically. Burnout time for wood particles of different size at different temperatures are calculated and the result is presented in diagrams. It is difficult to calculate the residence time for fuel particles in a flame in a generally useful way with any precision. Some diagrams that can be used to approximate the residence time of an aerodynamically small particle, in different parts of a flame, as a function of fuel load and burner diameter are presented. The results of CFD-simulations (with Fluent) of the trajectories of different sized fuel particles in a 20 and a 10 MW flame are shown in 20 pictures. Colour coding is used to show the particle temperature, residence time and combustion stage along the trajectories. The final discussion is based on the analysis of 3 real installations of burners in the size 9 - 20 MW.

  13. Treatment and disposal of radioactive wastes from nuclear power plants. Program for encapsulation, deep geologic deposition and research, development and demonstration; Kaernkraftavfallets behandling och slutfoervaring. Program foer inkapsling, geologisk djupfoervaring samt forskning, utveckling och demonstration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    Programs for RD and D concerning disposal of radioactive waste are presented. Main topics include: Design, testing and manufacture of canisters for the spent fuels; Design of equipment for deposition of waste canisters; Material and process for backfilling rock caverns; Evaluation of accuracy and validation of methods for safety analyses; Development of methods for defining scenarios for the safety analyses. 471 refs, 67 figs, 21 tabs.

  14. Effects of Non Process Elements in the chemical recovery system of paper mills; Effekter av PFG foer integrerade pappersbruk vid indunstning och foerbraenning av bioslam i sodapannan

    Energy Technology Data Exchange (ETDEWEB)

    Dahlbom, Johan [AaF Process AB, Stockholm (Sweden); Wadsborn, Rickard [STFI-Packforsk AB, Stockholm (Sweden)

    2005-09-01

    Effluent treatment of pulp and paper mills generates a biological sludge that according to Swedish implementation of EU-directives from 2005 has to be taken care of by incineration or by production of soil for agriculture or ground cover. An alternative way to take care of the sludge is incineration in the recovery boiler. This method is used in two Finish and two Swedish pulp mills with good results. The purpose of this project is to investigate the consequences for integrated pulp and paper mills when the biological sludge is incinerated in the recovery boiler. The biological sludge contents Non Process Elements, NPE, which increase the risks of incrustations in the system and increase the need of make up lime. This study comprises the following NPE: aluminum, silicon, phosphorus, chloride, potassium, manganese, magnesium, iron, copper, barium and calcium. The simulation program WinGEMS 5.0 (Pacific Simulation) was used in the study to predict the levels of NPE in the recovery system of the Kraft mills. Three different pulp and paper mills were selected for the study, Billerud Skaerblacka, ASSI Domaen Froevi and SCA Obbola. The mills are different concerning raw materials, process, degree of own produced pulp and paper products. All three the mills have effluent treatment and use the method of activated sludge that generates a surplus of biological sludge. The results of the study proved that for Skaerblacka mill the method is applicable. For Obbola the prerequisites are somewhat more complicated, the effluent treatment generates considerably higher amount of sludge per ton pulp produced due to the treatment technique and use of waste paper (40 %) for the paper machine. The high input of aluminum with the sludge will give troublesome incrustations of sodium-aluminum-silicate on the heat surfaces in the evaporation plant. To eliminate the aluminum from the system magnesium can be added to the black liquor which will precipitate as the double salt hydrotalcite in

  15. The use of indentor testing in determining the creep properties locally - a review; Nyttjande av indentorteknik foer bestaemning av krypegenskaper lokalt - litteraturstudie

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Peder [Det Norske Veritas AB, Stockholm (Sweden)

    2000-07-01

    A review has been performed with the purpose of examining what has been published regarding the creep indentation technique. In the reference list a selected choice of published papers is presented. Furthermore, the use of the technique is explained, a presentation is made of the parameters that are possible to determine and, finally, the limitations of the technique are discussed. In the investigated publications, the theoretical aspects of the indentation technique are discussed, as well as the possibilities of applying the technique in practice. From the published material, it is obvious that creep indentation testing is a technique suitable when the creep deformation properties of a material are to be determined. It seems though, that the technique so far mostly has been used in academically designed experiments and not in a larger industrial scale. The creep indentation testing technique seems to be a good complement to conventional uniaxial creep testing in determining the creep deformation properties of a material. Especially in testing of the creep deformation properties of weldments and parts of weldments, such as HAZ, the indentation testing technique can prove to be advantageous, as only a small amount of material is needed. In the line of business of plants operating in the high temperature range, where materials experience creep, there should be an interest in seeing a development of a testing standard for the creep indentation technique. This could be performed by doing a more comprehensive analysis of a selected choice of published papers, putting together their differences and similarities after which verifying experiments are pursued. In the end, it should be possible to come up with a draft standard for creep indentation testing.

  16. Technical development to increase the use of reed canary grass - Full scale demonstration; Teknikutveckling foer oekad etablering och nyttjande av roerflen - Demonstrationsfoersoek i fullskala

    Energy Technology Data Exchange (ETDEWEB)

    Oerberg, Haakan; Skoglund, Nils; Grimm, Alejandro; Bostroem, Dan; Oehman, Marcus

    2010-06-15

    Introducing fuels from agricultural crops into the heat and power sector in Sweden is a desired and needed development, thus it is connected to some obstacles. For the crop producers it is important to use the most efficient handling for harvest, collection, loading and transport technology in order to reach low production costs. For the fuel consumers it is of high importance that these fuels work together with other utilized fuels in mixtures without complications. This includes fuel mixing, fuel feeding, combustion behavior and ash transformation mechanisms. Specifically for the combustion process, gaseous and particle emissions, ash behavior and deposit formation on cooled surfaces should not be negatively effected by mixing in agricultural crops. In this study these aspects of the energy crop reed canary grass (RCG) have been examined. The recommended harvest period for harvesting RCG in Sweden is during springtime when the crop from the year before is collected, called delayed harvest. During this period the grass is very dry and has been harvested in this project with an average water content of 11,3 %. Two major different harvest systems have been tested. One where the energy grass is chopped directly in the field by a chopper connected to a wagon. The other system was based on baling the crop with round balers or big square balers. The chopped or baled material is transported 6 km to a farm center or terminal for unloading. Further transport to CHP (Combined Heat and Power) plant, 12 km, was done with road truck (135 m3). In the case of field chopped RCG the mixing of the other fuels has been easily done since the material was well chopped (40-50 mm). The RCG was mixed into a mixture of peat and wood to a share of 10-12% of the total energy content of the mixture. Also the baled material was transported to a farm centre or terminal for unloading the farm wagon and loading on a road truck (135 m3). In this case an additional procedure is needed for chopping

  17. Development of methods for determination of PAH based on measured CO-content; Metodutveckling foer indirekt bestaemning av PAH-halt utgaaende fraan maett momentan CO-halt

    Energy Technology Data Exchange (ETDEWEB)

    Ingman, Rolf; Schuster, Robert [AaF Energikonsult Stockholm AB, Stockholm (Sweden)

    2001-02-01

    The aim of the project 'Development of methods for determination of PAH based on measured CO-content' is to investigate the possibility to develop a method for continuous optimisation of NO{sub x}-emissions by decreased air ratio, without significant increase of polyaromatic hydrocarbons such as PAH. The general idea has been to find a indirect online method to predict the emissions of heavier hydrocarbons by: - creating a correlation between the content of CO and PAH, - controlling the air ratio by the CO-content, and - integrating the calculated PAH-content from CO-content. Today many boilers are operated with a low air ratio to minimise the NO{sub x} content and the NO{sub x}-fee. A low ratio increases the risk of high CO contents in the flue gas as well as increased contents of VOC and PAH. Other boilers are operated with high air ratios in order to minimise the CO content, which in some cases will result in unnecessary high NO{sub x} emissions. One of the main difficulties in optimising the air ratio to the most environmental friendly level is the lack of a suitable and well proven PAH instrument. There are today no available instruments for instantaneous and continuous measurement of PAH. PAH is normally measured as an average value during a period of at least one hour. It is not possible to detect short peaks. The development of the CO-method has been based on data from a CFB-boiler in Korsta in Sundsvall (Vaermeforskrapport 541). The data shows a clear correlation between THC and CO. The correlation seems to be mostly dependent of moisture content and load. The development presented in the report shows that it is possible to find a method to predict the PAH content from the CO-content in the flue gas. The next phase aims to improve and implement the method, by measurements and adaptation in a plant. The practical use of the method is as a tool to optimise the emission of CO, NO{sub x}, THC and PAH and/or to predict the PAH-emission during

  18. Technique for compressed bundles for harvest of whole straw willow. Pilot study; Teknik foer komprimerande helskottsskoerd av salix i buntform. Foerstudie

    Energy Technology Data Exchange (ETDEWEB)

    Eriksson, Hans (Vaesteraeng Lantbruk AB (Sweden))

    2008-06-15

    The pilot study was initiated by the need of a new technology that has been raised from the problem, and by the specifications of requirements, that has been described from the project 'Salix Maelardalen'. The need has been crystallized by the energy company Maelarenergi AB, Vaesteraas, in their handling of bio fuel, among many other fuels. The company Maelarenergi AB can see a potential in the use of Salix of a considerable volume. There is a special need by the means of the big volume handling of Salix, since the Salix raw material must be able to be delivered under a longer period or for intermediate storage. 8-9 months could be an adequate storage period. The possibility for intermediate storage could do the flow of fuel raw material to the combined power and heating plant is harmonized to the special requirements of fuel. The storage capability in chipped raw Salix chips is very short and that's why chipped Salix are not going to be a sustainable system combined with the handle of big volume together with portioned inflow to the plant. The production of Salix chips in a system of direct chipping is a very delicate system. The ground conditions with frozen and dry grounds are important for a system with heavy machines. The last years have not given such climate conditions. A big problem with practicability has been coming up. The number of days for contract work during the harvest period without interruption, because of hard conditions, has been decreased to the level that the capacity very considerably falls below what is economical defensible. The needs of larger areas for harvesting during fewer days under good conditions counteract each other. In the 'hot flow' during the harvest when the harvest machine will work with escort vehicles/container transports in the field can be impossible to realize because of for example the breakdown of the soil structure. The organization around 'hot flow system' is a very heavy programme

  19. Possible consequences of climate change on the Swedish energy sector - impacts, vulnerability and adaptation; Taenkbara konsekvenser foer energisektorn av klimatfoeraendringar. Effekter, saarbarhet och anpassning

    Energy Technology Data Exchange (ETDEWEB)

    Gode, Jenny; Axelsson, Johan; Eriksson, Sara; Holmgren, Kristina; Hovsenius, Gunnar; Kjellstroem, Erik; Larsson, Per; Lundstroem, Love; Persson, Gunn

    2007-06-15

    The events of recent years clearly demonstrate the far-reaching consequences of extreme weather situations on the energy system, particularly in the case of severe damage to transmission lines in connection with violent storms. Many climate researchers predict an increase in extreme weather events. Against this background, in 2005 Elforsk initiated this project where the aim has been to examine how climate change can affect plant operation, production conditions and energy usage patterns, how undesirable consequences can be predicted and what long-term measures may be necessary. Another central objective has been to bring about a dialogue between climate researchers, energy consultants/engineers and buyers for the energy industry. The inclusion of both positive and negative consequences has been an important ambition of the project. One key aspect of the project has been to develop climate scenarios for the next 20-25 years that describe possible changes in climate variables with relevance for the energy system. Based on these and literature studies, contact with experts and internal assessments, an analysis has been made of the possible impacts on hydropower, wind power, biofuel supply, natural gas supply, the power transmission network and energy usage. The project findings, which have also been discussed at a workshop with representatives from the energy industry, did not reveal any acute need for adaptation aside from those measures already being taken, for example to make the transmission system less vulnerable to weather conditions. Furthermore, the results indicate increased production potential for both hydropower and wind power. The production potential for hydropower stations from the Dalaelven River northwards would appear to increase by 2-10%. Estimates for the southern watercourses are less certain, but the production potential may decrease. Since around 80% of the country's hydropower is produced in the northern watercourses, this indicates an

  20. Assessment of two techniques for drying of easily degradable organic bio-waste; Bedoemning av tvaa tekniker foer torkning av laett nedbrytbart organiskt matavfall

    Energy Technology Data Exchange (ETDEWEB)

    Raaholt, Birgitta; Bergstroem, Birgitta; Broberg, Agneta; Holtz, Emma; Nordberg, Ulf; Del Pilar Castillo, Maria; Baky, Andras

    2011-10-15

    incoming material to treatment plants, energy consumption, cost, and climate impact. The quality of the dried material was evaluated with respect to purity degree, shelf-life stability, nutritional content, bio fuel potential and rehydration properties. In the system analysis, each drying technology, combined with a supposed subsequent digestion process, was compared to today's system for collection and digestion of food waste. An initial assessment of the potential of the microwave-vacuum drying process was made, as an alternative technique for hygienisation of food waste which contains animal by-products (ABP). The results indicate that the microwave process would be possible to adjust, in order to meet the time-temperature requirements for hygienisation. However, complementing studies are required to optimise and control the process towards the required microbiological reduction. Dried material has, as expected, advantages from both an odour and storage point of view; the lower water content corresponds to lower water activity and accordingly longer shelf-life and reduced risk for e.g. mould growth and odour. Even if energy is needed for drying the material, there are environmental advantages at collection of food waste (at transport distances less than about 50 km). Digestion experiments showed that dried food waste from households in Goeteborg did not result in any significant differences in methane exchange, with regard to organic matter (VS), expressed as m{sup 3}CH{sub 4}/tonne VS, compared with fresh food waste. Dried waste from food establishments in Boraas showed significantly lower methane exchange, with respect to organic matter (VS), than fresh food waste. The reasons for this need to be further investigated. A project delimitation was that the techniques were evaluated based upon food waste which was collected during a relatively short period of time. The target group of the project is the Swedish food industry, personnel responsible for waste

  1. The potential of utilizing wood ash and peat ash on organic soils in Sweden; Arealer foer skogsgoedsling med traeaska och torvaska paa organogena jordar i Sverige

    Energy Technology Data Exchange (ETDEWEB)

    Haanell, Bjoern [Swedish Univ. of Agricultural Sciences, Umeaa (Sweden). Dept. of Silviculture

    2004-01-01

    . Additional calculations were made concerning the area of abandoned peat fields ready for after-use by afforestation. The main part of the site selection was made in five steps. First, the non-productive sites (which produce less than 1 m{sup 3}/ha/yr) were rejected. Also sites with peat cover shallower than 30 cm were excluded. In the next step it was decided to restrict the ash fertilization to areas with drains in good condition, and to sites where the field vegetation was dominated by 'better shrubs' (Vaccinium myrtillus, V. vitis idaea, Equisetum silvaticum, and tall sedges) or 'low sedge' (Eriophorum vaginatum, Scirpus caespitosus, and other low Cyperaceae plants). Finally, open areas, seedling stands, and young forests were rejected in favour of un-thinned and thinned mid-rotation, and mature and old stands. According to these selection criteria the most suitable sites for ash fertilization are drained, productive peatlands characterized by thinning stands or older stands where the field vegetation is dominated by better shrubs or low sedge plants. The selection comprises 190,000 ha. Most of these areas are located in North Sweden (90,000 ha), whereas Central and South Sweden accounted for 30,000 ha and 70,000 ha, respectively. In addition to this, 2,000-3,000 ha of abandoned peat fields ready for afforestation should be added within a period of about 5 years. The requirement for phosphorus when peatland forests are fertilized is 40-50 kg/ha. From this, and from studies on the variation of phosphorus content and bulk density of wood ash of various origins, it can be calculated that a proper ash fertilization dose would be 3-5 t/ha. The nutrient content in the ash may however often prove lower than in the reported studies, in which case larger doses than 5 t/ha would be required. The present annual production of bio-ash in Sweden is about 250,000-300,000 tonnes. If it were desired to amend all sites (190,000 ha) identified in this study by using 5

  2. Intelligent soot blowing for boilers co-firing waste and biofuel; Behovsstyrd sotblaasning foer bio- och avfallseldade pannor - inventering och teknikval

    Energy Technology Data Exchange (ETDEWEB)

    Kjoerk, Anders [S.E.P. Scandinavian Energy Project AB, Goeteborg (Sweden)

    2003-11-01

    To achieve optimum boiler operation and performance it is necessary to control the cleanliness and limit the fouling of the heat transfer surfaces. Historically, the heating surfaces in boilers firing biomass and waste are cleaned by steamblowing soot blowers on scheduled time-based and/or parameter-based intervals or by mechanical methods. With the advent of fuel switching strategies and use of mixed-in industrial waste, the control of heating surface cleanliness has become even more crucial for these boilers. Scheduled and/or parameter based approaches do not easily address operational changes. As plant operators push to achieve greater efficiency and performance from their boilers, the ability to more effectively optimize cleaning cycles has become increasingly important. If soot blowing is done only when and where it is required rather than at set intervals, unit performance can be maintained with reduced blowing, which saves steam. Two philosophical approaches toward intelligent soot blowing are currently being applied in the industry. One incorporates heat flux monitors to gather real-time heat transfer data to determine which areas of the furnace need cleaning. The other uses indirect temperature and pressure data to infer locations where soot blowing is needed, and is mainly applied for controlling soot blowers in the superheater and economiser area. The heat flux monitors are so fare used for control of the furnace wall blowers. A system using temperature, pressure and flow data does not require much additional instrumentation as compared with what is available on a standard boiler. However the blower control system must be capable of operating blowers on an individual basis. For advanced options it should also be possible to adjust the speed of the soot blower and the steam pressure. The control program could be more or less advanced but the ability to model heating surfaces and determine real-time cleanliness is crucial for an intelligent soot blowing

  3. Summary of the program 'Environmentally correct utilization of ashes' at Vaermeforsk 2002-2005; Syntes av delprogrammet 'Miljoeriktig anvaendning av askor' foer 2002-2005

    Energy Technology Data Exchange (ETDEWEB)

    Bjurstroem, Henrik [AaF-Process AB, Stockholm (Sweden)

    2006-04-15

    The present report summarizes the results during the period 2002-2005. The report also presents an evaluation of the programme and suggests priorities for the coming period, 2006-2008. During the period 2002-2005, 61 projects have been performed. The utilizations of ashes that have been targeted are, as materials in geotechnical construction, and as nutrients in forestry. Work has been carried out in four main areas: geotechnical constructions, landfills, recycling ash to soils, environment and chemistry. Among all results obtained, the following progresses along lines of development may be shown: A proposal for environmental guidelines on the utilization of ashes in construction; A battery of tests that allow a discussion of the geotechnical properties of ashes in e.g. road construction; Continued development of the use of ashes together with wastewater sludge as a cover for landfills, the use of fly ash in gravel roads; Use of ashes from biofuels in concrete; Evidence for the positive effects of spreading ashes on forest growth; and A method to classify those by-products from combustion that have mirror entries in the EWC as hazardous or non-hazardous. Each year, about 1 million tons of by-products, or ashes, are produced at the Swedish combustion plants. The largest potential market for these materials is in construction, which consumes some 100 million tons of materials each year. The most immediate uses are in road construction, in landfills or as ballast or filler in concrete. The most important barriers for use in e.g. road construction have been the absence of methods to assess the impact on the environment, and the absence of relevant testing methods for the geotechnical properties of ashes. Both these barriers were addressed in parallel projects. Guidelines with general limit values for road construction have been proposed. This work has also yielded an unexpected result: leaching of metals from ashes to soil and water is usually not the problem that it

  4. Summary of the program 'Environmentally correct utilization of ashes' at Vaermeforsk 2002-2005; Syntes av delprogrammet 'Miljoeriktig anvaendning av askor' foer 2002-2005

    Energy Technology Data Exchange (ETDEWEB)

    Bjurstroem, Henrik [AaF-Process AB, Stockholm (Sweden)

    2006-04-15

    The present report summarizes the results form the projects that have carried out during the period 2002-2005. The report presents an evaluation of the programme and suggests priorities for the coming period, 2006-2008. The Ash Programme is a wide initiative including building up knowledge, work on guidelines, development work and communication. During the period 2002-2005, 61 projects have been performed. The utilizations of ashes that have been targeted are as secondary or recovered materials in geotechnical construction on the one hand, as nutrients in forestry on the other hand. Work has been carried out in four main areas: geotechnical constructions, landfills, recycling ash to soils, environment and chemistry. Among all results obtained, the following progresses along lines of development may be shown: A proposal for environmental guidelines on the utilization of ashes in construction; A battery of tests that allow a discussion of the geotechnical properties of ashes in e.g. road construction; Continued development of the use of ashes together with wastewater sludge as a cover for landfills, the use of fly ash in gravel roads; Use of ashes from biofuels in concrete; Evidence for the positive effects of spreading ashes on forest growth; A method to classify those by-products from combustion that have mirror entries in the EWC as hazardous or non-hazardous. Each year, ca 1 million tons of by-products, or ashes, are produced at the Swedish combustion plants. The large potential market for these materials is in construction, which consumes ca 100 million tons of materials each year. The most immediate uses are in road construction, in landfills or as ballast or filler in concrete. The most important barriers for a use in e.g. road construction have been the absence of a method to assess the impact of the use of ashes in a construction on the environment, as well as the absence of relevant testing methods for the geotechnical properties of ashes. Both these

  5. Evaluation and optimization of a method for pretreatment of sorted household wastes for biogas production; Utvaerdering och optimering av metod foer foerbehandling av kaellsorterat hushaallsavfall till biogasproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Bohn, Irene (NSR AB, Helsingborg (Sweden)); Carlsson, My (AnoxKaldnes AB, Lund (Sweden)); Eriksson, Ylva; Holmstroem, David (Lund Univ., Lund (Sweden))

    2010-04-15

    well as in the reject, visual plastic objects and large fibres were present, while no visual large particles occurred in the liquid fraction. Analyses of the methane yield in the three streams showed that the liquid fraction has the highest methane potential. However, a considerable amount of methane can be produced from the reject and thus, a large amount of potential methane is lost in the present situation. Approximately 65 % of the methane that potentially can be produced in the slurry can be produced from the liquid fraction. Methane is a gas with a high energy value and can be converted to vehicle fuel. The energy in the reject is converted into heat and electricity when combusted in a combined heat and power plant. Just over 12 GWh of methane could be produced from digestion of the slurry. The corresponding energy production from the liquid fraction is 8 GWh. From combustion of the reject, almost 2 GWh of electricity can be produced and close to 4 GWh of heat. The total amount of energy that can be produced by applying the screw press is therefore larger when the screw press is applied. However, the energy in the gas is considered as a higher form of energy and the selectivity in the screw press should therefore be increased in order to achieve a higher methane production from the liquid fraction. Though, pre-treatment in the screw press gives benefits in terms of increased operational stability and a possibility to use the digestion sludge as a bio-fertiliser. A lab scale study was carried out in order to investigate the possibilities of increasing the methane production from the liquid fraction. By increasing the temperature in the mixing tank, more fat can be dissolved in the liquid phase in the slurry and be separated to the liquid fraction. According to the results of the study, the energy production could increase with close to 40 % if the fat concentration in the liquid fraction is increased by 35 %. Experiments carried out with electroporation of the

  6. Medicinal Plants.

    Science.gov (United States)

    Phillipson, J. David

    1997-01-01

    Highlights the demand for medicinal plants as pharmaceuticals and the demand for health care treatments worldwide and the issues that arise from this. Discusses new drugs from plants, anticancer drugs, antiviral drugs, antimalarial drugs, herbal remedies, quality, safety, efficacy, and conservation of plants. Contains 30 references. (JRH)

  7. Plant walkdown

    International Nuclear Information System (INIS)

    Kostov, M.

    2000-01-01

    This report covers the following: preparatory steps for performing plant walk-down; the objective of the first plant walk-down; plant walk-down procedures; earthquake screening evaluation; walk-down documentation; second plant walk-down. The following objectives concerning the plant walk-down(s) were achieved. The plant system configuration is verified in order to proceed with event tree and fault tree analyses. Systems interactions, other types of dependencies or plant unique features are identified. he safety related components that are judged to generically possess high capacities (i.e., larger than the earthquake review level) have been verified to contain no weaknesses. Further analyses needed to establish the capacities of remaining safety-related components are identified and necessary field data are obtained. Information on components is obtained to assist in HCLPF (fragility) evaluation and peer review of the seismic margin study

  8. Aquatic plants

    DEFF Research Database (Denmark)

    Madsen, T. V.; Sand-Jensen, K.

    2006-01-01

    Aquatic fl owering plants form a relatively young plant group on an evolutionary timescale. The group has developed over the past 80 million years from terrestrial fl owering plants that re-colonised the aquatic environment after 60-100 million years on land. The exchange of species between terre...... terrestrial and aquatic environments continues today and is very intensive along stream banks. In this chapter we describe the physical and chemical barriers to the exchange of plants between land and water.......Aquatic fl owering plants form a relatively young plant group on an evolutionary timescale. The group has developed over the past 80 million years from terrestrial fl owering plants that re-colonised the aquatic environment after 60-100 million years on land. The exchange of species between...

  9. Electronic plants

    Science.gov (United States)

    Stavrinidou, Eleni; Gabrielsson, Roger; Gomez, Eliot; Crispin, Xavier; Nilsson, Ove; Simon, Daniel T.; Berggren, Magnus

    2015-01-01

    The roots, stems, leaves, and vascular circuitry of higher plants are responsible for conveying the chemical signals that regulate growth and functions. From a certain perspective, these features are analogous to the contacts, interconnections, devices, and wires of discrete and integrated electronic circuits. Although many attempts have been made to augment plant function with electroactive materials, plants’ “circuitry” has never been directly merged with electronics. We report analog and digital organic electronic circuits and devices manufactured in living plants. The four key components of a circuit have been achieved using the xylem, leaves, veins, and signals of the plant as the template and integral part of the circuit elements and functions. With integrated and distributed electronics in plants, one can envisage a range of applications including precision recording and regulation of physiology, energy harvesting from photosynthesis, and alternatives to genetic modification for plant optimization. PMID:26702448

  10. Ash and sludge covering of mine waste - Final report. Benefits and/or risks using ash and sludge for covering of weathered mine waste; Aska och roetslam som taet- och taeckskikt foer vittrat gruvavfall - Slutrapport. Foerdelar och/eller risker med att anvaenda aska och slam som taet- och taeckskikt foer vittrat gruvavfall

    Energy Technology Data Exchange (ETDEWEB)

    Baeckstroem, Mattias; Karlsson, Ulrika [Oerebro Univ. (Sweden). Man-Technology-Environment Research Centre

    2006-02-15

    One of the main sources for metal pollution in Sweden is mine waste. One way to decrease the leaching of metals from mine waste areas are covering which decreases the volume of acid drainage. There is a shortage of appropriate materials to use for covering and excavation of till and clay from the environment might cause damages on the landscape. Previous studies have demonstrated that sludge and ashes are suitable materials for covering of waste deposits. When covering mine waste with ash and sludge various positive effects would arise, since the production of drainage water decreases as well as the pH increases due to the high buffer capacity of the ash. In Ervalla outside Oerebro an area with mine waste (tailings) has been covered with ash and sludge. This area gives a unique possibility to study benefits and/or risks with the covering of mine waste with ash and sludge. Unfortunately, the covering was not, from the start, carried out in a way that made it possible to evaluate the data. For instance, data about the surface and groundwater quality prior to the covering is lacking. Sulphidic minerals are also very common in the area, giving rise to acidic groundwater from other parts of the area, which haven't been remediated. This report is a final report where all phases are presented (phase 1 and 2). Focus in phase 1 has been on characterization of the material that has been used for covering and initiation of a monitoring program. In phase 2 focus has been on evaluation of monitoring data and the pros and cons of the deposit regarding the environment. Preliminary findings indicate that that the covering increases the leaching of some metals whereas the leaching of some metals decreases. An increase was observed for pH, calcium, potassium, sodium, arsenic, barium, chromium and copper. A decrease in the concentration of iron, nickel, cobalt, lead and zinc was observed. Other benefits with the remediation is also discussed (increased plant growth and an area

  11. Plant embryogenesis

    NARCIS (Netherlands)

    Vries, de Sacco C.; Weijers, Dolf

    2017-01-01

    Land plants are called ‘embryophytes’ and thus, their collective name is defined by their ability to form embryos. Indeed, embryogenesis is a widespread phenomenon in plants, and much of our diet is composed of embryos (just think of grains, beans or nuts; Figure 1). However, in addition to embryos

  12. Plant Macrofossils

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Records of past vegetation and environmental change derived from plant remains large enough to be seen without a microscope (macrofossils), such as leaves, needles,...

  13. T Plant

    Data.gov (United States)

    Federal Laboratory Consortium — Arguably the second most historic building at Hanford is the T Plant.This facility is historic in that it's the oldest remaining nuclear facility in the country that...

  14. Lunar Plants

    Data.gov (United States)

    National Aeronautics and Space Administration — We present an open design for a first plant growth module on the Moon (LPX). The primary science goal of lunar habitat is to investigate germination and initial...

  15. Alien plants

    Science.gov (United States)

    2018-04-01

    No-one’s ever travelled to an extrasolar planet, or even observed one that we’re sure harbours life. But if plants do exist on such alien worlds, we can have fun speculating what form they might take.

  16. Plant simulator

    International Nuclear Information System (INIS)

    Fukumitsu, Hiroyuki

    1998-01-01

    A simulator of a reactor plant of the present invention comprises a plurality of distributed computers, an indication processing section and an operation section. The simulation calculation functions of various kinds of plant models in the plant are shared by the plurality of computers. The indication processing section controls collection of data of the plant simulated by the computers and instructions of an operator. The operation section is operated by the operator and the results of operation are transmitted to the indication processing section, to conduct operation trainings and display the results of the simulation. Each of the computers and the indication processing portion are connected with each other by a network having a memory for common use. Data such as the results of calculation of plant models and various kinds of parameters of the plant required commonly to the calculators and the indication processing section are stored in the common memory, and adapted to be used by way of the network. (N.H.)

  17. Plant automation

    International Nuclear Information System (INIS)

    Christensen, L.J.; Sackett, J.I.; Dayal, Y.; Wagner, W.K.

    1989-01-01

    This paper describes work at EBR-II in the development and demonstration of new control equipment and methods and associated schemes for plant prognosis, diagnosis, and automation. The development work has attracted the interest of other national laboratories, universities, and commercial companies. New initiatives include use of new control strategies, expert systems, advanced diagnostics, and operator displays. The unique opportunity offered by EBR-II is as a test bed where a total integrated approach to automatic reactor control can be directly tested under real power plant conditions

  18. Plant intelligence

    Science.gov (United States)

    Lipavská, Helena; Žárský, Viktor

    2009-01-01

    The concept of plant intelligence, as proposed by Anthony Trewavas, has raised considerable discussion. However, plant intelligence remains loosely defined; often it is either perceived as practically synonymous to Darwinian fitness, or reduced to a mere decorative metaphor. A more strict view can be taken, emphasizing necessary prerequisites such as memory and learning, which requires clarifying the definition of memory itself. To qualify as memories, traces of past events have to be not only stored, but also actively accessed. We propose a criterion for eliminating false candidates of possible plant intelligence phenomena in this stricter sense: an “intelligent” behavior must involve a component that can be approximated by a plausible algorithmic model involving recourse to stored information about past states of the individual or its environment. Re-evaluation of previously presented examples of plant intelligence shows that only some of them pass our test. “You were hurt?” Kumiko said, looking at the scar. Sally looked down. “Yeah.” “Why didn't you have it removed?” “Sometimes it's good to remember.” “Being hurt?” “Being stupid.”—(W. Gibson: Mona Lisa Overdrive) PMID:19816094

  19. PLANT DIVERSITY

    Science.gov (United States)

    Habitat change statistics and species-area curves were used to estimate the effects of alternative future scenarios for agriculture on plant diversity in Iowa farmlands. Study areas were two watersheds in central Iowa of about 50 and 90 square kilometers, respectively. Future s...

  20. Inventory of future power and heat production technologies. Partial report Boilers/Combustion/Steam cycle for district heating and cogeneration; Inventering av framtidens el- och vaermeproduktionstekniker. Delrapport Pannor/Foerbraenning/Aangcykel foer fjaerrvaerme och kraftvaerme

    Energy Technology Data Exchange (ETDEWEB)

    Schuster, Robert (AaF Process, Stockholm (Sweden))

    2008-12-15

    The energy market of today is turbulent and it is quite clear that big changes in the consumption pattern are going to occur, due to the expansion in Asia and the expected Climate Change. The EU has, as a first step, stated in a directive that the consumption of renewable energy in the heat and power sector should be increased to 20 % and in the transportation sector to 10 % by the year 2020, a target which is high above current levels in most of the EU countries. It is reasonable to believe the European demand of renewable energy will create a shortage of biomass and that the development and use of technology for energy production will therefore not only depend on what is technically possible. One scenario is that biomass is mainly used for the markets that have very few alternatives, such as the transportation sector and small scale CHP units. We have today a relatively high electrical consumption through a stable grid and district heating nets in almost all densely populated areas. Large high efficiency power plants combined with heat pump technology will probably prevent any significant expansion of the district heating nets. A third major net for gas distribution seems not to be a feasible solution. Local nets for production of biogas from wet waste for different purposes, including EvGT units with 55% efficiency may however be good solution for some areas. There are a number of cycles and technical solutions to increase the electrical efficiency which could be applied also on smaller plants. The total efficiency will however not increase, only the el/heat ratio and it is not obvious that the higher investment cost for indirect cycles, bottom cycles or extreme steam data in combination with the risk of lower availability is a feasible solution. Especially waste to energy plants, with their need of high utilisation time, are sensitive to long production interruptions. The existing heat sinks in Sweden will however be efficiently used for electrical production

  1. Flue gas wells to minimize dust and acidic components in small-scale burning of field fuel, further development; Roekgasbrunn foer minimering av stoft och sura komponenter vid smaaskalig foerbraenning av aakerbraenslen, vidareutveckling

    Energy Technology Data Exchange (ETDEWEB)

    Yngvesson, Johan; Roennbaeck, Marie; Arkeloev, Olof

    2011-01-15

    Agricultural derived solid fuels are more problematic to combust in small-scale heating plants than conventional wood fuels. Their high content of ash, chlorine and sulphur leads to increased emissions of dust, sulphur dioxide and hydrogen chloride in the flue gases. By transporting the flue gases to a flue gas well where it condenses, and separates dust and sour components, enables a cost effective flue gas purification for small-scale heating plants (50 kW - 10 MW) of agricultural derived solid fuels. This project have studied two heating plants using flue gas wells with the aim to add to the knowledge about how a flue gas wells may look like and to quantify how much emissions of dust, chlorine and sulphur in the flue gases are reduced. The project also aimed to summon regulations and laws regarding the handling of the condensate that develop in the flue gas well. In the project measures were conducted on two different heating plants with mounted flue gas wells: a 60 kW biofuels boiler combusting grains and red canary grass and a 1 MW batch fired boiler combusting wheat straw. Measurements on flue gases were conducted with and without water injection in the flue gases. The flue gas wells reduced dust emissions of up to 80 %. The best reduction was achieved at the 60 kW heating plant when firing red canary grass. Firing grains in the same plant lead to 7 % reduction of the dust emissions. In the 1 MW heating plant firing wheat straw the flue gas well accomplished 40 % reduction of dust emissions. The boiler ability to achieve complete combustion, hence minimize the content of volatile and semi-volatile components in the flue gas, is largely affecting the flue gas well ability to reduce dust emissions. This did not, however, affect the reduction of dust in the flue. Chlorine emissions was reduced by up to 88 % by a flue gas well. Water injection made a big difference on reduction of chlorine emission from grain combustion. Sulphur emissions was reduced by 50

  2. Stress tolerant plants

    OpenAIRE

    Rubio, Vicente; Iniesto Sánchez, Elisa; Irigoyen Miguel, María Luisa

    2014-01-01

    [EN] The invention relates to transgenic plants and methods for modulating abscisic acid (ABA) perception and signal transduction in plants. The plants find use in increasing yield in plants, particularly under abiotic stress.

  3. Plant Host Finding by Parasitic Plants: A New Perspective on Plant to Plant Communication

    OpenAIRE

    Mescher, Mark C; Runyon, Justin B; De Moraes, Consuelo M

    2006-01-01

    Plants release airborne chemicals that can convey ecologically relevant information to other organisms. These plant volatiles are known to mediate a large array of, often complex, interactions between plants and insects. It has been suggested that plant volatiles may have similar importance in mediating interactions among plant species, but there are few well-documented examples of plant-to-plant communication via volatiles, and the ecological significance of such interactions has been much d...

  4. Nuclear power plants

    International Nuclear Information System (INIS)

    1985-01-01

    Data concerning the existing nuclear power plants in the world are presented. The data was retrieved from the SIEN (Nuclear and Energetic Information System) data bank. The information are organized in table forms as follows: nuclear plants, its status and type; installed nuclear power plants by country; nuclear power plants under construction by country; planned nuclear power plants by country; cancelled nuclear power plants by country; shut-down nuclear power plants by country. (E.G.) [pt

  5. LNG plant combined with power plant

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, I; Kikkawa, Y [Chiyoda Chemical Engineering and Construction Co. Ltd., Tokyo (Japan)

    1997-06-01

    The LNG plant consumers a lot of power of natural gas cooling and liquefaction. In some LNG plant location, a rapid growth of electric power demand is expected due to the modernization of area and/or the country. The electric power demand will have a peak in day time and low consumption in night time, while the power demand of the LNG plant is almost constant due to its nature. Combining the LNG plant with power plant will contribute an improvement the thermal efficiency of the power plant by keeping higher average load of the power plant, which will lead to a reduction of electrical power generation cost. The sweet fuel gas to the power plant can be extracted from the LNG plant, which will be favorable from view point of clean air of the area. (Author). 5 figs.

  6. LNG plant combined with power plant

    International Nuclear Information System (INIS)

    Aoki, I.; Kikkawa, Y.

    1997-01-01

    The LNG plant consumers a lot of power of natural gas cooling and liquefaction. In some LNG plant location, a rapid growth of electric power demand is expected due to the modernization of area and/or the country. The electric power demand will have a peak in day time and low consumption in night time, while the power demand of the LNG plant is almost constant due to its nature. Combining the LNG plant with power plant will contribute an improvement the thermal efficiency of the power plant by keeping higher average load of the power plant, which will lead to a reduction of electrical power generation cost. The sweet fuel gas to the power plant can be extracted from the LNG plant, which will be favorable from view point of clean air of the area. (Author). 5 figs

  7. Problems concerning food production, supply and use caused by radioactive deposition: A study directed towards needs for early decision making after radioactive fallout; Radiakproblem inom livsmedelssektorn: En studie inriktad paa behoven foer beslutsfattande i tidigt skede efter radioaktivt nedfall

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, R

    1995-12-01

    The primary aim of this study is to analyze and describe how a radioactive deposition after nuclear weapons employment outside Sweden would affect the domestic food production in a short time perspective and in the sequence of events from primary production over processing and transport to food consumption. The study is an attempt at a comprehensive treatment of knowledge needed as a basis for decisions on operative issues, often of a time-urgent nature. Actions to alleviate the problems pertinent to the food supply in the event of radioactive fallout are also discussed, although without any claim of exhaustive coverage. Other aspects, as the economical consequences of the disturbances due to the fallout situation (or of possible counteractions) are not dealt with, however. With certain restrictions mentioned in the text the results are also applicable in connection with radioactive deposition caused by accidental release from a nuclear power plant. 60 refs, 32 figs.

  8. Program description for the program Fuel program conversion 2011-07-01 - 2015-06-30; Programbeskrivning foer programmet Braensleprogrammet omvandling 2011-07-01 - 2015-06-30

    Energy Technology Data Exchange (ETDEWEB)

    2011-04-15

    The Fuel program conversion is included as one of three programs in a cohesive commitment to increased, sustainable and efficient production and use of indigenous and renewable fuels that are implemented by the Swedish Energy Agency during the period July 1, 2011 - June 30, 2015. The program focuses on increasing knowledge and development of technologies for processing of the fuel feedstock, and conversion to primarily heat and electricity in plants up to about 10 MW. Issues of particular concern is to strengthen competitiveness, efficiency and sustainability in the chain from raw material to end use, and increasing raw material base by developing knowledge and technologies for new materials that are current. The program includes basic and applied research, development and demonstration. Within the sub-area Processing efforts are prioritized which streamline and reduce costs in different types of processing operations. Processing here means not just technology for pelleting and briquetting, but also sub-processes that prepare, dry, handle or process raw materials in other ways. Within the sub-area Conversion to heat and electricity in the range <10 MW, the focus is principally, on one hand increasing the knowledge of the interaction between fuel and combustion plant, and on the other hand to implement results of research in collaboration with users and equipment suppliers. Furthermore, great importance is given to increasing the competitiveness of local heating in the transition from oil to renewable heat supply and the use of new fuel materials and fuels. Questions about the fuel supply from forestry and agriculture, including issues of sustainability, environment and resource use are treated in the two parallel running programs, the Fuel program supply and the Fuel program sustainability

  9. Decision support system on line to minimize the NO{sub x} emission. Results from Oerebro Energi; Beslutsstoed on line foer minimering av NO{sub x}. Resultat fraan Oerebro Energi

    Energy Technology Data Exchange (ETDEWEB)

    Bergdahl, B G; Liao, B; Sieurin, J [EuroSim AB, Nykoeping (Sweden)

    1996-05-01

    A Decision Support System to reduce NO{sub x} emission from combustion processes with SNCR system have been developed and tested in full scale at Oerebro Energy. The boiler is a 165 MWh{sub th} CFB and have been fired with a mixture of biomass, peat and coal. The results proves that the EuroSim method works to calculate the derivative included in the Decision Support System. The Decision Support System is a tool for the operator of the plant, he will be informed of the advantage of making an increase or decrease of the ammonia flow or excess air. The trend curves that are presented to the operator includes information about the economic value to make an adjustment of the ammonia flow. The derivative dNO{sub x}/dO{sub 2} shows the advantage of making a reduction in the excess air level, concerning the fee for NO{sub x}. In this case it is important to take into consideration the risk for understoichiometric combustion and corrosion. The results from the full scale test in the Oerebro Plant shows that during some time periods it is economical to shut off the ammonia flow. The derivative dNO{sub x}/dAF is under the profitability limit. This indicate that the cost for the ammonia is higher than the fee for the NO{sub x} emission. If the ammonia flow is added in excess, the emission of ammonia and N{sub 2}O will increase. During other time periods the Decision Support System shows that it is profitable to increase the ammonia flow, the derivative is lower than -0,2. The derivative dNO{sub x}/dO{sub 2} is normally between 10 and 20 (ppm/%). This indicate that it is a great potential to reduce the NO{sub x} fee by decreasing the excess air level in the boiler. 3 refs, 23 figs

  10. Present status and an appreciation of the consequences for recreation and outdoor leisure activities from siting a nuclear waste repository at Forsmark; Nulaegesanalys samt bedoemning av konsekvenser foer rekreation och friluftsliv av ett slutfoervar i Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Ottosson, Pia [Atrax Energi AB, Stockholm (Sweden)

    2007-07-15

    This report describes how the area around Forsmark is used with respect to recreation and outdoor life. It also describes the impact of the final repository on recreation and outdoor life if it is located in Forsmark. The studied area is situated in the parish of Forsmark in the municipality of Oesthammar. Forsmark nuclear power plant and the final repository for radioactive operational waste, SFR, are situated within the area and there are both houses and holiday houses. The area is used for leisure pursuit by inhabitants and employees at FKA and SKB, but also by a number of different associations and by tourists. Statistical data shows that the parish of Forsmark is sparsely populated. The area was previously dominated by one big landowner and the land surrounding the nuclear power plant was inaccessible to the general public during that period. The outdoor life is therefore less widespread here than along other parts of the east coast. The value of the area does not lie in paths and trails, bike tracks and bathing places, but in the unspoiled countryside, the wildlife and the bird life. Recreation such as hunting and fishing is very popular in the area. The construction of a final repository will increase traffic and hence increase noise and motion in the area. This will mainly impact the enjoyment value for the people spending time in the area. No other significant consequences are expected as the final repository will be mainly situated within the existing industrial complex and hence the character of the area should remain unchanged.

  11. Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Roland

    2005-12-15

    Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result in lime mud difficult to dewater, has not become true. Important experiences have come out which could be used as a base in further investigations.

  12. Plant host finding by parasitic plants: a new perspective on plant to plant communication.

    Science.gov (United States)

    Mescher, Mark C; Runyon, Justin B; De Moraes, Consuelo M

    2006-11-01

    Plants release airborne chemicals that can convey ecologically relevant information to other organisms. These plant volatiles are known to mediate a large array of, often complex, interactions between plants and insects. It has been suggested that plant volatiles may have similar importance in mediating interactions among plant species, but there are few well-documented examples of plant-to-plant communication via volatiles, and the ecological significance of such interactions has been much debated. To date, nearly all studies of volatile-mediated interactions among plant species have focused on the reception of herbivore-induced volatiles by neighboring plants. We recently documented volatile effects in another system, demonstrating that the parasitic plant Cuscuta pentagona uses volatile cues to locate its hosts. This finding may broaden the discussion regarding plant-to-plant communication, and suggests that new classes of volatile-meditated interactions among plant species await discovery.

  13. Plant host finding by parasitic plants: A new perspective on plant to plant communication

    Science.gov (United States)

    Mark C. Mescher; Justin B. Runyon; Consuelo M. De Moraes

    2006-01-01

    Plants release airborne chemicals that can convey ecologically relevant information to other organisms. These plant volatiles are known to mediate a large array of, often complex, interactions between plants and insects. It has been suggested that plant volatiles may have similar importance in mediating interactions among plant species, but there are few well-...

  14. Steam slaking of lime - kinetics and technology. New energy effective lime slaking technology in kraft pulping; Aangslaeckning av kalk - kinetik och teknik. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Roland

    2008-06-15

    Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional lime burning and slaking methods are that heat recovery is bad and heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant, and to recover heat at higher temperatures. The forecasted method means that lime is slaked with water vapour, for example combined with an indirect heated lime mud drier and a lime kiln. This project is a follow-up to pilot tests performed in a specific machine equipment at year 2006. The target group is pulp and paper industry using the kraft process. The owner of this new project is Carnot AB and the project is performed inside the Vaermeforsk Program for Pulp and Paper Industry 2006-2008. Partners and advisers in project group have been KTH Energy Processes, CTH Energy and Environment, LTH Chemical Technology, SMA Mineral AB, and reference group from STORA Enso Skoghall, Sodra Cell, M-Real Husum and SCA Packaging Piteaa. The task in this stage has included market investigations and laboratory tests. Contacts have been made with suppliers, preliminary dimensioning of process equipment and budget offers are received. Economic calculations have been made out of the offers. The laboratory tests are done as an examination paper at KTH Energiprocesser on the reactivity of burned lime from kraft lime kiln when it is slaked with water vapour instead of green liquor. The vapour intended to be used is at atmospheric pressure or even down to 0,2 atm. Complementary addition to these laboratory

  15. Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, Roland

    2003-07-15

    Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Project owner has been the Swedish company Torkapparater AB, and the project is performed inside the 'Vaermeforsk Program for Pulp and Paper Industry 2004-2005'. Other partners, besides SMA Svenska Mineral AB, has been Stora Enso Skoghalls Bruk, Carnot AB, AaF Process AB and KTH Energiprocesser. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result

  16. Kansas Power Plants

    Data.gov (United States)

    Kansas Data Access and Support Center — The Kansas Power Plants database depicts, as point features, the locations of the various types of power plant locations in Kansas. The locations of the power plants...

  17. Gender in Plants

    Indian Academy of Sciences (India)

    What is the difference between plant sex and plant gender? Why does stress .... environmental sex determination is often predictable. Sunlit patches favour .... ensures that these self-incompatible plants receive cross-pollen only. i emporal ...

  18. Engineered Plants as Biosensors

    National Research Council Canada - National Science Library

    Stewart, C

    2003-01-01

    The aim of the research was the creation of a model biosensing plant that could detect plant diseases and to characterize the utility of laser induced fluorescence imaging for detecting the inducible (LIFI) plant signal...

  19. Small-scale bio fuelled heat and power - requirements for standardized technical and fuel solutions from a systems perspective; Smaaskalig biobraenslebaserad kraftvaerme - foerutsaettningar foer standardiserade loesningar med avseende paa teknik och braenslen i ett systemperspektiv

    Energy Technology Data Exchange (ETDEWEB)

    Nystroem, Olle; Johansson, Kent; Steinwall, Pontus [Sycon Energikonsult AB, Malmoe (Sweden)

    2001-01-01

    Different techniques for small-scale heat and power generation have been investigated. The included cycles are steam turbine, diesel engine, Otto engine, Stirling engine, gas turbine and organic Rankine cycle (ORC). For steam turbines, Stirling engine, and indirectly fired gas turbines, the combustion can be placed in a relatively conventional furnace, which gives a fairly free choice of fuel. In other cycles like the traditional gas turbine cycle, diesel engine and Otto engine, the fuel should be in the gas or liquid phase. Experiments are in progress to use wood pf (pulverised fuel) as fuel. The technique for plants based on steam turbine, diesel engine, Otto engine, conventional gas turbine and ORC based on different forms of bio fuel exist already today. For Stirling engine, gas turbine with HAT cycle (Humid Air Turbine) and indirectly fired gas turbine further development is needed before the technique will be commercially available using bio fuel. An interesting process coupling is a gas engine combined with a gasifier. This coupling can be a competitive choice to the other processes if the problems with gas cleaning can be solved.

  20. Plant stress signalling: understanding and exploiting plant-plant interactions.

    Science.gov (United States)

    Pickett, J A; Rasmussen, H B; Woodcock, C M; Matthes, M; Napier, J A

    2003-02-01

    When plants are attacked by insects, volatile chemical signals can be released, not only from the damaged parts, but also systemically from other parts of the plant and this continues after cessation of feeding by the insect. These signals are perceived by olfactory sensory mechanisms in both the herbivorous insects and their parasites. Molecular structures involved can be characterized by means of electrophysiological assays, using the insect sensory system linked to chemical analysis. Evidence is mounting that such signals can also affect neighbouring intact plants, which initiate defence by the induction of further signalling systems, such as those that increase parasitoid foraging. Furthermore, insect electrophysiology can be used in the identification of plant compounds having effects on the plants themselves. It has been found recently that certain plants can release stress signals even when undamaged, and that these can cause defence responses in intact plants. These discoveries provide the basis for new crop protection strategies, that are either delivered by genetic modification of plants or by conventionally produced plants to which the signal is externally applied. Delivery can also be made by means of mixed seed strategies in which the provoking and recipient plants are grown together. Related signalling discoveries within the rhizosphere seem set to extend these approaches into new ways of controlling weeds, by exploiting the elusive potential of allelopathy, but through signalling rather than by direct physiological effects.

  1. Evaluation of MELTGUARD{sup TM} - a measuring system for control of fireside corrosion in boilers; Utvaerdering av MELTGUARD{sup TM} - ett maetsystem foer kontroll av roekgassidig korrosion i pannor

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, Pamela [Vattenfall Utveckling AB, Stockholm (Sweden)

    2001-10-01

    Studsvik AB has developed and now owns the patent for a product called MELTGUARD. According to information from Studsvik, Meltguard is a measuring probe that shows in real-time how much corrosion is occurring and that can reduce costs and increase the lifetime of power boilers burning biomass. The product consists of a tubular air-cooled probe which is exposed in the flue gas through an existing inspection port. The electrodes in the probe react with the flue gas and ash deposit and corrosion is registered as the short-circuited corrosion current (using the zero resistance method) between rings made of the investigated material. The aim of the project was to independently evaluate Meltguard, compare it with a conventional corrosion probe and to publish the results for the Swedish thermal power industry. Two steels have been compared on the probes (a Meltguard-probe can accommodate a maximum of two test pieces), with about the same temperature. Measurements have been carried out with the steels SS2218 (T22) and Esshete 1250 on a Meltguard probe in the biomass fired boiler at Naessjoe combined heat and power plant during the period November 2000 to March 2001. For a 48 hour period sulphur was added to the fuel supply to change the fuel chemistry and influence the corrosion rate. The corrosion current for SS2218 was unstable, fluctuating considerably throughout the measuring period, and was greatly affected by soot-blowing. Usually, soot-blowing resulted in a marked decrease in the corrosion current. No simple or clear relationship between the boiler load and the average corrosion current could be determined. The corrosion current for Esshete 1250 was mostly stable, about 20{mu}A. The current for SS2218 was a little higher than that for E1250, but the relationship between current and corrosion rate was unclear. It was obviously not a linear function as the corrosion measured in 2218, when the testing was completed, was approximately four times greater than that in E

  2. Follow-up for the years 2000-2002 of productivity studies for the operation of CLAB; Uppfoeljning foer aaren 2000-2002 av undersoekning av produktivitetsutvecklingen vid driften av CLAB

    Energy Technology Data Exchange (ETDEWEB)

    Lundberg, Haakan [AaF-Energi and Miljoe AB, Stockholm (Sweden)

    2003-04-01

    SKB hands every year over, on behalf of the power companies, to SKI a cost calculation for spent fuel handling and dismantling of the Swedish nuclear power plants. SKI has tried to investigate the future impact which the growth of money in the Nuclear Waste Fund might give in relation to the change of consumer price index, CPI. The long term yield of the Fund has been related to the change of CPI, as the bigger part of the fund money has been invested in real interest rate bonds, issued by the Swedish state. The cost development has been studied with an index named 'KBS-3-index', which is a basket of weighted factor price indexes based on the SKB programme. Since 1986 and up to 2002, the KBS-3-index has increased about 102%, but CPI only about 70%. If this discrepancy should continue during the whole period when Fund money should be available, the Fund would be insufficient. But the difference between KBS-3-index and CPI might be eliminated due to a future productivity development. At the moment, SKI has no knowledge about future productivity development in the SKB programme. A closer analysis of the productivity and efficiency development in the facilities operated by SKB is therefore applicable. Nearest to study is the productivity at the operation of CLAB, Central Interim Storage Facility for Spent Nuclear Fuel. The work in CLAB is receiving and storing of spent nuclear fuel and core components. The consumption of all production factors can be measured in economical means. Here the total production factors are defined as the sum of the annual operation costs and the sum of annuities for reinvestments during the year. The development of total productivity is increasing slightly, but decreasing in the end. Normal for a new business is that the productivity is rising sharply in the beginning. Here the productivity is slightly decreasing in the beginning, and then rising, decreasing, rising and finally decreasing. The project 'compact storing

  3. Present status and an appreciation of the consequences for recreation and outdoor leisure activities from siting a nuclear waste repository at Oskarshamn; Nulaegesanalys samt bedoemning av konsekvenser foer rekreation och friluftsliv av ett slutfoervar i Oskarshamn

    Energy Technology Data Exchange (ETDEWEB)

    Dahlstroem, Kristina

    2007-07-15

    This report describes recreation and outdoor life in and around Simpevarp/Laxemar area. It also describes the impact of constructing a final repository for spent nuclear fuel on the outdoor life. The study area in this report is situated in the parish of Misterhult, in the municipality of Oskarshamn. Oskarshamn nuclear power plant (OKG) and the interim storage facility for spent nuclear fuel (Clab) are situated within the area. The parish of Misterhult is sparsely populated and includes both houses and holiday cottages. The area is used for various kinds of recreation by inhabitants from surrounding villages and employees at OKG and SKB (Swedish Nuclear Fuel and Waste Management Co), and also by a number of different associations and by tourists. Misterhult archipelago has the highest values for recreation and outdoor life in the study area. Many water related activities, such as swimming, sailing, fishing, diving, kayaking and canoeing are conducted in the region Hamnefjaerden, Kraakelund and a walking track called Ostkustleden are three other places in the study area which are popular for outdoor life. SKB and OKG facilities are also visited by many tourists. Disturbances to the recreation and outdoor life during construction and operation of a final repository and a interim storage facility will occur in the form of increased noise and movement in the area, mostly from the traffic. The consequences of these disturbances are: Decreased serenity, which will probably decrease the enjoyment value for the people spending time in the area. The final repository in Laxemar will likely require road access that will cross the walking track. Various prevention and compensation measures, such as noise restrictions and a new section of the walking track at Ostkustleden, are suggested to minimise and/or mitigate the consequences. Also measures that increase the value of recreation and outdoor life are listed, for example an exhibition about the areas nature and culture

  4. Basis for applying for exemption according to species protection regulation. Final repository for spent nuclear fuel at Forsmark; Underlag till ansoekan om dispens enligt artskyddsfoerordningen. Slutfoervar foer anvaent kaernbraensle i Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    2011-02-15

    SKB will submit applications for permits and admissibility under the Environmental Act and under the Nuclear Activities Act to construct and operate a disposal facility for spent nuclear fuel at Forsmark. In the final repository the spent nuclear fuel from Swedish nuclear power plants is placed in order to protect human health and the environment against harmful effects of ionizing radiation. Construction and operation of the disposal facility in Forsmark will make an impact, give effects and consequences for the natural environment. Utilization of land for the construction of the facility and the impact on ground water as a result of groundwater drainage is expected to have negative consequences for the species included in species protection regulation. Thus, the planned activity require exemption from species protection regulation (SFS 2007:845). The purpose of this document is to provide a basis for an application for exemption under 14 paragraph species protection regulation from the prohibitions of 4, 6, 7 and 8 paragraph species protection regulation. A basis for the exemption application is that the proposed activity is considered to have an 'overriding public interest' prescribed in 14 paragraph species protection regulation. The document reports the impact, effects and consequences of the planned activities on species covered in the species protection regulation. The impact on protected species can be divided into two categories: - Direct effects on protected species and their habitats by utilization of the land. - Indirect effects on protected species and their habitats in the drainage of groundwater and the effect on groundwater levels. The document also includes a description of planned actions to prevent, restrict and compensate for the effects and consequences that the activity may cause. By applying for an exemption under 14 paragraph species protection regulation in a separate order from the application for permit according to chapters 9

  5. Basis for applying for exemption according to species protection regulation. Final repository for spent nuclear fuel at Forsmark; Underlag till ansoekan om dispens enligt artskyddsfoerordningen. Slutfoervar foer anvaent kaernbraensle i Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    2011-02-15

    SKB will submit applications for permits and admissibility under the Environmental Act and under the Nuclear Activities Act to construct and operate a disposal facility for spent nuclear fuel at Forsmark. In the final repository the spent nuclear fuel from Swedish nuclear power plants is placed in order to protect human health and the environment against harmful effects of ionizing radiation. Construction and operation of the disposal facility in Forsmark will make an impact, give effects and consequences for the natural environment. Utilization of land for the construction of the facility and the impact on ground water as a result of groundwater drainage is expected to have negative consequences for the species included in species protection regulation. Thus, the planned activity require exemption from species protection regulation (SFS 2007:845). The purpose of this document is to provide a basis for an application for exemption under 14 paragraph species protection regulation from the prohibitions of 4, 6, 7 and 8 paragraph species protection regulation. A basis for the exemption application is that the proposed activity is considered to have an 'overriding public interest' prescribed in 14 paragraph species protection regulation. The document reports the impact, effects and consequences of the planned activities on species covered in the species protection regulation. The impact on protected species can be divided into two categories: - Direct effects on protected species and their habitats by utilization of the land. - Indirect effects on protected species and their habitats in the drainage of groundwater and the effect on groundwater levels. The document also includes a description of planned actions to prevent, restrict and compensate for the effects and consequences that the activity may cause. By applying for an exemption under 14 paragraph species protection regulation in a separate order from the application for permit according to chapters 9 and 11

  6. Open absorption heat pump for waste heat utilization in the forest industry. A study of technical and economic potential; Oeppen absorptionsvaermepump foer uppgradering av spillvaerme fraan skogsindustrin. Studie av teknisk och ekonomisk potential

    Energy Technology Data Exchange (ETDEWEB)

    Westermark, Mats; Vidlund, Anna

    2006-02-15

    steam (for use in pulp and paper plants) is technically more advanced. The high temperature level demands absorption liquids with high boiling point elevation (sodium hydroxide) and driving steam at 25 bar. The example studied uses waste heat at 50 deg C for production of low pressure steam at 1.2 bar, i.e. slightly above atmospheric pressure. Such low pressure steam can be used for steam injection in paper machines or upgraded to process steam of higher pressure by steam compression.

  7. Plants get sick too!

    Science.gov (United States)

    Although many people may never have given consideration to plant health, plants can suffer from a wide range of diseases. These plant diseases are caused by micro-organisms, including bacteria, fungi, and viruses. The audience will be introduced to short case studies of several plant diseases that m...

  8. Plant extraction process

    DEFF Research Database (Denmark)

    2006-01-01

    A method for producing a plant extract comprises incubating a plant material with an enzyme composition comprising a lipolytic enzyme.......A method for producing a plant extract comprises incubating a plant material with an enzyme composition comprising a lipolytic enzyme....

  9. Radioactive uptake by plants

    Energy Technology Data Exchange (ETDEWEB)

    Horak, O

    1986-01-01

    The fundamentals of radionuclide uptake by plants, both by leaves and roots are presented. Iodine, cesium, strontium and ruthenium are considered and a table of the measured concentrations in several agricultural plants shortly after the Chernobyl accident is presented. Another table gives the Cs and Sr transfer factors soil plants for some plants. By using them estimates of future burden can be obtained.

  10. Plant Biology Science Projects.

    Science.gov (United States)

    Hershey, David R.

    This book contains science projects about seed plants that deal with plant physiology, plant ecology, and plant agriculture. Each of the projects includes a step-by-step experiment followed by suggestions for further investigations. Chapters include: (1) "Bean Seed Imbibition"; (2) "Germination Percentages of Different Types of Seeds"; (3)…

  11. Plants' essential chemical elements

    Science.gov (United States)

    Kevin T. Smith

    2007-01-01

    Every garden center and hardware store sells fertilizer guaranteed to "feed" plants. In a strict sense, we can't feed plants. Food contains an energy source. Green plants capture solar energy and make their own food through photosynthesis! Photosynthesis and other metabolic processes require chemical elements in appropriate doses for plants to survive...

  12. A method for mapping the motion and temperature history of fuel particles in grate boilers and waste incinerators - stage 1; Metod foer kartlaeggning av braenslepartiklars roerelse och temperaturhistorik i rosterpannor/avfallsugnar - etapp 1

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsson, Lennart; Blom, Elisabeth; Hald Pedersen, Niels; Moritz, Anders; Maardsjoe, Olle; Oskarsson, Jan; Petersson, Mats

    2000-04-01

    radiation hazards connected to the proposed methods. Use of the methods requires authorization by the radiation protection agency. However, this is not believed to be a problem, although the radioactive isotopes must only be handled by authorized persons. It should be emphasised that the planned use do not mean that persons are exposed to radiation of any health-related significance whatsoever. Action plans for near-accident scenarios are described, which mean that no risks for persons and/or the plant should arise. In contrast, the risks for limited access to the boiler or shutdown during 10-14 days in case of near-accident must be assessed in each case. The assessment of the proposed methods leads to the conclusion that the technical possibilities to use the methods are realistic. Validation trials are therefore proposed to be conducted on a biomass boiler and on a waste incinerator. The prerequisites for these trials, a proposed validation program as well as a preliminary time schedule, is finally given.

  13. Proposal of performance indicators/model for Operational Readiness Verification (ORV) at restart after a planned shutdown; Framtagning av bedoemningsfaktorer/modell foer utvaerdering av driftklarhetsverifiering (DKV) infoer uppstart efter revisionsavstaellning

    Energy Technology Data Exchange (ETDEWEB)

    Hollnagel, Erik; Nygren, Magnus [Linkoeping Univ. (Sweden). Dept. of Computer and Information Science

    2005-12-15

    The objectives of the study reported here were to propose a model that can be used in the analysis of possible future ORV-related events and to outline a set of performance indicators that can be used by the inspectorate to assess a utility's level of readiness if an ORV-event should take place. Together the two objectives serve to improve the inspectorate's ability to ensure that the utilities maintain an adequate capability to respond. The background for the current study is the nine ORV events that occurred in Sweden between 1995- 1998, as well as the findings of a previous study of safety during outage and restart of nuclear power plants project. This study found that the three levels or types of tests that occur in ORV were used according to need rather than according to a predefined arrangement or procedure, and that tasks were adapted relative to the different types of embedding and the degree of correspondence between nominal and actual ORV. The organisation's coping with the complexity of ORV was discussed by the relation between expectations and surprises, how planning was used as control, attention to details, and the practices of shift changes. It is a truism that accidents are analysed and interpreted relative to a commonly accepted understanding of their nature. This understanding is, however, relative rather than absolute, and has changed significantly during the last decade. In the 1990s, accidents were analysed step by step, and explanations and recommendations therefore emphasised specific rather than generic solutions. The present study illustrates this by going through the responses to the nine ORV events. Following that, the nine events are analysed anew using a contemporary understanding of accidents (a systemic model), which emphasises that incidents more often arise from context induced performance variability than from failures of people. The alternative interpretation provided by a systemic model is illustrated by a detailed

  14. Development of the SKI Handbook for reviewing PSA after the review of the of a PSA level 2 study; Utveckling av SKIs Tillsynshandbok foer PSA utifraan granskningen av en PSA Nivaa-2 studie

    Energy Technology Data Exchange (ETDEWEB)

    Lindholm, Ilona; Sairanen, Risto [VTT Processes, Helsinki (Finland)

    2003-02-01

    should have been taken to harmonise the formalism which is different in case of the HS3 event trees. There is very little discussion on utilisation of the results. Half of the core damage frequency results in the containment end state SAM, which is not very well defined. SAM states in which the core is not damaged should have been separated from the SAM states in which the core damage occurs but containment is calculated to remain intact. A discussion should be presented how the plant could be taken to a stable state from SAM conditions. The SKI handbook was utilised in the review. It was generally found suitable although the guide focuses more on conduction of PSA than review of it. Quality control, documentation of central assumptions and the goal for comprehensive assessment is emphasised. Tables showing the most important aspects of the a PSA review are useful. To reflect the usual way of conducting a Level 2 PSA, the Guide should even more emphasise the need for consistency between the specific phenomenological studies and with the source term estimates. The guide points out that a result from a PSA does not only mean the quantitative results but also the background information, uncertainty and sensitivity analysis and description of models and data. Availability of this material was found central also when conducting the review.

  15. HMI-Design of System Solutions in Control Rooms. Description of a Working Process from a Human-Machine Perspective; MMI-design av systemloesningar i kontrollrum. Arbetsprocess foer utformning utifraan ett maenniska-maskinperspektiv

    Energy Technology Data Exchange (ETDEWEB)

    Bligaard, Lars-Ola; Andersson, Jonas; Thunberg, Anna; Osvalder, Anna-Lisa

    2008-01-15

    between operators and machines. The content can be used both for new development projects and for upgrading of already existing control room designs. The main target group for the report is the development engineers at the plant, who work close to the supplier, and the people who should plan and guide the development work in the control room. The purpose of the report is to deliver knowledge about how to consider a human-machine perspective in the development process. The report presents what is important to consider, but does not in detail show design solutions. The report is also a usable tool for those people who should do the actual screen designs, but then it should be used together with hand-book data and guide-lines referred to. The report begins with a description of basic concepts and definitions within the area of HMI. This is followed by a description of the HMI development working process. The working process includes five steps; planning, requirements, conceptual design, detailed design, and commissioning. The steps also include methodology for data collection and evaluation. Finally, the handbook also contains short summaries of the different steps in the working process, where important points to consider are brought forward

  16. Status, remaining service-life and quality assurance of PP-materials in flue-gas applications; Status, kvarvarande livslaengd och kvalitetssaekring av PP-material i anlaeggningar foer rening och kondensering av roekgaser

    Energy Technology Data Exchange (ETDEWEB)

    Jacobson, Karin

    2011-10-15

    Background: The project is intended to provide a better understanding of how the service life of PP-materials is affected when used in flue-gas applications. It intends to form a basis for the development of relevant techniques and a methodology from which it is possible to give advice and guidance so that the quality of PP-materials can be ensured for a given desired service life. In addition it aims as being able to assess the status and remaining life of PP-materials in current components. Project outline - An inventory, contact and choice of facilities for closer cooperation. Plants with high proportions of PP in the equipment have been prioritised. - Visits to the chosen sites during shut-down periods for inspection and collection of samples from different PP details for further analysis in the laboratory. Collection of operating data and experiences of the use of PP (operating time/exposure conditions in different parts, component substitutions that have been made, etc.). - Systematic studies of the processes and mechanisms for stabiliser consumption over time. - Developing methods and methodology on which advice and guidance can be based so that the quality of PP-materials can be ensured for a given desired service life. The goal is to be able to assess the status and remaining service-life of the PP-materials in flue-gas applications. Results and Conclusions: It has been found that corrosion is relatively rare and that the main factors limiting the use and longevity of polypropylene are the thermal properties (thermal expansion and heat distortion). Leaching of stabilisers from the material is also commonly found but only a few cases of oxidative degradation, as a result of this, have been observed. An important part of the project has been to develop techniques and methodologies to assure the quality PP-material for a desired service life, and to assess the status and remaining life of the PP- materials in flue-gas applications. To do this, samples that

  17. Plant Research '75

    Energy Technology Data Exchange (ETDEWEB)

    1975-01-01

    Research is reported on stomatal regulation of the gas exchanges between plant and environment; inhibitory effects in flower formation; plant growth and development through hormones; hormone action; development and nitrogen fixation in algae; primary cell wall glycoprotein ectensin; enzymic mechanisms and control of polysaccharide and glycoprotein synthesis; molecular studies of membrane studies; sensory transduction in plants; regulation of formation of protein complexes and enzymes in higher plant cell and mechanism of sulfur dioxide toxicity in plants. (PCS)

  18. PLANT BIOPRINTING: NOVEL PERSPECTIVE FOR PLANT BIOTECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Adhityo WICAKSONO

    2015-12-01

    Full Text Available Bioprinting is a technical innovation that has revolutionized tissue engineering. Using conventional printer cartridges filled with cells as well as a suitable scaffold, major advances have been made in the biomedical field, and it is now possible to print skin, bones, blood vessels, and even organs. Unlike animal systems, the application of bioprinting in simple plant tissue cells is still in a nascent phase and has yet to be studied. One major advantage of plants is that all living parts are reprogrammable in the form of totipotent cells. Plant bioprinting may improve scientists’understanding of plant shape and morphogenesis, and could serve for the mass production of desired tissues or plants, or even the production of plant-based biomaterial for industrial uses. This perspectives paper explores these possibilities using knowledge on what is known about bioprinting in other biosystems.

  19. Plutonium Plant, Trombay

    International Nuclear Information System (INIS)

    Yadav, J.S.; Agarwal, K.

    2017-01-01

    The journey of Indian nuclear fuel reprocessing started with the commissioning of Plutonium Plant (PP) at Trombay on 22"n"d January, 1965 with an aim to reprocess the spent fuel from research reactor CIRUS. The basic process chosen for the plant was Plutonium Uranium Reduction EXtraction (PUREX) process. In seventies, the plant was subjected to major design modifications and replacement of hardware, which later met the additional demand from research reactor DHRUVA. The augmented plutonium plant has been operating since 1983. Experience gained from this plant was very much helpful to design future reprocessing plant in the country

  20. Better plants through mutations

    International Nuclear Information System (INIS)

    1988-01-01

    This is a public relations film describing problems associated with the genetic improvement of crop plants through induced mutations. Mutations are the ultimate source of genetic variation in plants. Mutation induction is now established as a practical tool in plant breeding. The Joint FAO/IAEA Division and the IAEA's laboratory at Seibersdorf have supported research and practical implementation of mutation breeding of both seed propagated and vegetatively propagated plants. Plant biotechnology based on in vitro culture and recombinant DNA technology will make a further significant contribution to plant breeding

  1. Plant Phenotype Characterization System

    Energy Technology Data Exchange (ETDEWEB)

    Daniel W McDonald; Ronald B Michaels

    2005-09-09

    This report is the final scientific report for the DOE Inventions and Innovations Project: Plant Phenotype Characterization System, DE-FG36-04GO14334. The period of performance was September 30, 2004 through July 15, 2005. The project objective is to demonstrate the viability of a new scientific instrument concept for the study of plant root systems. The root systems of plants are thought to be important in plant yield and thus important to DOE goals in renewable energy sources. The scientific study and understanding of plant root systems is hampered by the difficulty in observing root activity and the inadequacy of existing root study instrumentation options. We have demonstrated a high throughput, non-invasive, high resolution technique for visualizing plant root systems in-situ. Our approach is based upon low-energy x-ray radiography and the use of containers and substrates (artificial soil) which are virtually transparent to x-rays. The system allows us to germinate and grow plant specimens in our containers and substrates and to generate x-ray images of the developing root system over time. The same plant can be imaged at different times in its development. The system can be used for root studies in plant physiology, plant morphology, plant breeding, plant functional genomics and plant genotype screening.

  2. Plant tissue culture techniques

    Directory of Open Access Journals (Sweden)

    Rolf Dieter Illg

    1991-01-01

    Full Text Available Plant cell and tissue culture in a simple fashion refers to techniques which utilize either single plant cells, groups of unorganized cells (callus or organized tissues or organs put in culture, under controlled sterile conditions.

  3. Plant Tissue Culture

    Indian Academy of Sciences (India)

    Admin

    Plant tissue culture is a technique of culturing plant cells, tissues and organs on ... working methods (Box 2) and discovery of the need for B vita- mins and auxins for ... Kotte (Germany) reported some success with growing isolated root tips.

  4. Fertilization in Flowering Plants

    Indian Academy of Sciences (India)

    IAS Admin

    Ecology and the Environ- ment, Bengaluru as ... remaining plants, it is an abiotic agent (abiotic pollination), .... tion was slow until the origin of flowering plants and evolution of ..... Although pollination is generally a mutual interaction in a major-.

  5. Plant proton pumps

    DEFF Research Database (Denmark)

    Gaxiola, Roberto A.; Palmgren, Michael Gjedde; Schumacher, Karin

    2007-01-01

    Chemiosmotic circuits of plant cells are driven by proton (H+) gradients that mediate secondary active transport of compounds across plasma and endosomal membranes. Furthermore, regulation of endosomal acidification is critical for endocytic and secretory pathways. For plants to react...

  6. Terrestrial plant methane production

    DEFF Research Database (Denmark)

    Mikkelsen, Teis Nørgaard; Bruhn, Dan; Møller, Ian M.

    We evaluate all experimental work published on the phenomenon of aerobic methane (CH4) generation in terrestrial plants. We conclude that the phenomenon is true. Four stimulating factors have been observed to induce aerobic plant CH4 production, i.e. cutting injuries, increasing temperature...... the aerobic methane emission in plants. Future work is needed for establishing the relative contribution of several proven potential CH4 precursors in plant material....

  7. Plant aquaporins: roles in plant physiology.

    Science.gov (United States)

    Li, Guowei; Santoni, Véronique; Maurel, Christophe

    2014-05-01

    Aquaporins are membrane channels that facilitate the transport of water and small neutral molecules across biological membranes of most living organisms. Here, we present comprehensive insights made on plant aquaporins in recent years, pointing to their molecular and physiological specificities with respect to animal or microbial counterparts. In plants, aquaporins occur as multiple isoforms reflecting a high diversity of cellular localizations and various physiological substrates in addition to water. Of particular relevance for plants is the transport by aquaporins of dissolved gases such as carbon dioxide or metalloids such as boric or silicic acid. The mechanisms that determine the gating and subcellular localization of plant aquaporins are extensively studied. They allow aquaporin regulation in response to multiple environmental and hormonal stimuli. Thus, aquaporins play key roles in hydraulic regulation and nutrient transport in roots and leaves. They contribute to several plant growth and developmental processes such as seed germination or emergence of lateral roots. Plants with genetically altered aquaporin functions are now tested for their ability to improve plant resistance to stresses. This article is part of a Special Issue entitled Aquaporins. Copyright © 2013 Elsevier B.V. All rights reserved.

  8. Plants under dual attack

    NARCIS (Netherlands)

    Ponzio, C.A.M.

    2016-01-01

    Though immobile, plants are members of complex environments, and are under constant threat from a wide range of attackers, which includes organisms such as insect herbivores or plant pathogens. Plants have developed sophisticated defenses against these attackers, and include chemical responses

  9. Growing Plants and Minds

    Science.gov (United States)

    Presser, Ashley Lewis; Kamdar, Danae; Vidiksis, Regan; Goldstein, Marion; Dominguez, Ximena; Orr, Jillian

    2017-01-01

    Many preschool classrooms explore plant growth. However, because many plants take a long time to grow, it is often hard to facilitate engagement in some practices (i.e., since change is typically not observable from one day to another, children often forget their prior predictions or cannot recall what plants looked like days or weeks earlier).…

  10. Fundaments of plant cybernetics.

    Science.gov (United States)

    Zucconi, F

    2001-01-01

    A systemic approach is proposed for analyzing plants' physiological organization and cybernesis. To this end, the plant is inspected as a system, starting from the integration of crown and root systems, and its impact on a number of basic epigenetic events. The approach proves to be axiomatic and facilitates the definition of the principles behind the plant's autonomous control of growth and reproduction.

  11. Plant or Animal?

    Science.gov (United States)

    Bowman, Frank; Matthews, Catherine E.

    1996-01-01

    Presents activities that use marine organisms with plant-like appearances to help students build classification skills and illustrate some of the less obvious differences between plants and animals. Compares mechanisms by which sessile plants and animals deal with common problems such as obtaining energy, defending themselves, successfully…

  12. Small hydroelectric power plants

    International Nuclear Information System (INIS)

    Helgesen, Boerre

    2002-01-01

    Small hydroelectric power plants are power plants of 1 - 10 MW. For a supplier, this is an unnatural limit. A more natural limit involves compact engine design and simplified control system. The article discusses most of the engine and electrotechnical aspects in the development, construction and operation of such a plant

  13. Recognizing Plant Defense Priming.

    Science.gov (United States)

    Martinez-Medina, Ainhoa; Flors, Victor; Heil, Martin; Mauch-Mani, Brigitte; Pieterse, Corné M J; Pozo, Maria J; Ton, Jurriaan; van Dam, Nicole M; Conrath, Uwe

    2016-10-01

    Defense priming conditions diverse plant species for the superinduction of defense, often resulting in enhanced pest and disease resistance and abiotic stress tolerance. Here, we propose a guideline that might assist the plant research community in a consistent assessment of defense priming in plants. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Plant Physiology in Greenhouses

    NARCIS (Netherlands)

    Heuvelink, E.; Kierkels, T.

    2015-01-01

    Since 2004 Ep Heuvelink and Tijs Kierkels have been writing a continuing series of plant physiology articles for the Dutch horticultural journal Onder Glas and the international edition In Greenhouses. The book Plant Physiology in Greenhouses consists of 50 of their plant physiology articles. The

  15. Plants and people

    Science.gov (United States)

    Kathryn Lynch

    2012-01-01

    Salal! Salmonberries! Sword ferns! The Northwest is home to a great number of native plant species that humans have used for centuries. Sadly, many local children are unaware of the history and culture connecting people and plants. Yet, from the beginning of time, plants have provided us food, medicine, and material for clothing, shelter, transportation, decoration,...

  16. Plant Systems Biology (editorial)

    Science.gov (United States)

    In June 2003, Plant Physiology published an Arabidopsis special issue devoted to plant systems biology. The intention of Natasha Raikhel and Gloria Coruzzi, the two editors of this first-of-its-kind issue, was ‘‘to help nucleate this new effort within the plant community’’ as they considered that ‘‘...

  17. Plants of the Bayshore.

    Science.gov (United States)

    Bachle, Leo; And Others

    This field guide gives pictures and descriptions of plants that can be found along the San Francisco Bayshore, especially along the Hayward shoreline. The plants are divided into three categories, those of the mud-flat zone, the drier zone, and the levee zone. Eighteen plants are represented in all. The guide is designed to be used alone, with an…

  18. TRANSGENIC PLANT CONTAINMENT

    Science.gov (United States)

    The new technology using plant genetics to produce chemicals, pharmaceuticals, and therapeuitics in a wide array of new plant forms requires sufficient testing to ensure that these new plant introductions are benign in the environment. A recent effort to provide necessary guidan...

  19. Plant Breeding Goes Microbial

    NARCIS (Netherlands)

    Wei, Zhong; Jousset, Alexandre

    Plant breeding has traditionally improved traits encoded in the plant genome. Here we propose an alternative framework reaching novel phenotypes by modifying together genomic information and plant-associated microbiota. This concept is made possible by a novel technology that enables the

  20. Plant innate immunity

    Indian Academy of Sciences (India)

    Plants are invaded by an array of pathogens of which only a few succeed in causing disease. The attack by others is countered by a sophisticated immune system possessed by the plants. The plant immune system is broadly divided into two, viz. microbial-associated molecular-patterns-triggered immunity (MTI) and ...

  1. Diagnosing plant problems

    Science.gov (United States)

    Cheryl A. Smith

    2008-01-01

    Diagnosing Christmas tree problems can be a challenge, requiring a basic knowledge of plant culture and physiology, the effect of environmental influences on plant health, and the ability to identify the possible causes of plant problems. Developing a solution or remedy to the problem depends on a proper diagnosis, a process that requires recognition of a problem and...

  2. Hydroelectric Power Plants Dobsina

    International Nuclear Information System (INIS)

    Majercak, V.; Srenkelova, Z.; Kristak, J.G.

    1997-01-01

    In this brochure the Hydroelectric Power Plants Dobsina, (VED), subsidiary of the utility Slovenske Elektrarne, a.s. (Slovak Electric, plc. Bratislava) are presented. VED is mainly aimed at generating peak-load electrical energy and maintenance of operational equipment. Reaching its goals, company is first of all focused on reliability of production, economy and effectiveness, keeping principles of work safety and industry safety standards and also ecology. VED operates eight hydroelectric power plants, from which PVE Ruzin I and PVE Dobsina I are pump storage ones and they are controlled directly by the Slovak Energy Dispatch Centre located in Zilina thought the system LS 3200. Those power plants participate in secondary regulation of electrical network of Slovakia. They are used to compensate balance in reference to foreign electrical networks and they are put into operation independently from VED. Activity of the branch is focused mainly on support of fulfilment of such an important aim as electric network regulation. Beginnings of the subsidiary Hydroelectric Power Plants Dobsina are related to the year of 1948. After commissioning of the pump storage Hydroelectric Power Plants Dobsina in 1953, the plant started to carry out its mission. Since that time the subsidiary has been enlarged by other seven power plants, through which it is fulfilling its missions nowadays. The characteristics of these hydroelectric power plants (The pump-storage power plant Dobsina, Small hydroelectric power plant Dobsina II, Small hydroelectric power plant Rakovec, Small hydroelectric power plant Svedlar, Hydroelectric power plant Domasa, The pump-storage power plant Ruzin, and Small hydroelectric power plant Krompachy) are described in detail. Employees welfare and public relations are presented

  3. Methodology for Environmental Impact Assessment; Metodik foer miljoekonsekvensbedoemning

    Energy Technology Data Exchange (ETDEWEB)

    Malmlund, Anna (Structor Miljoebyraan Stockholm AB (Sweden))

    2010-12-15

    This report is an appendix to 'Environmental Impact Assessment Interim storage, encapsulation and disposal of spent nuclear fuel'. The appendix presents the methodology and criteria used in support investigations to conduct impact assessments.

  4. Statistics 2003 - in nuclear medicine; Isotopstatistik 2003 - foer nukleaermedicinsk verksamhet

    Energy Technology Data Exchange (ETDEWEB)

    Joensson, Helene; Richter, Sven

    2004-12-01

    In this compilation the use of radioactive substances in therapies and in vivo examinations during 2003 at all hospitals in Sweden is presented. For each nuclide, examination type, chemical form, way of administration, number of reporters, total number of examinations, mean activity used, and minimum and maximum activity is presented. Of the compilation it becomes known that during 2003 approximately 103,000 examinations and 3,300 therapies were performed. The total dose to the population from diagnostic procedures was 452 manSv.

  5. Policy instruments for offshore wind power; Styrmedel foer havsbaserad vindkraft

    Energy Technology Data Exchange (ETDEWEB)

    Soederholm, Patrik (Luleaa Technical Univ., Luleaa (Sweden))

    2009-10-15

    The future economic potential for offshore wind power is considered to be very good, and there is a strong interest in European wind power industry to improve the technology and generate additional experience. To enable such technology and a market introduction of offshore wind power it is believed that a supplementary or an alternative support for the offshore wind energy is required. This report aims to analyze conditions of different financial instruments to effectively support the rollout of offshore wind power in Sweden. Our mandate does not include an analysis whether any funding is economically justified or not, but a discussion about the objectives of such instruments is necessary for the second stage in order to discuss the instrument characteristics and design. The report takes up a number of different arguments in order to target a specific support for any single technology. An important message from this part of the analysis is that the strongest argument that can be used to extend a special generous support for offshore wind power is that its socio-economic costs may be lower, in the long run, than those which currently apply to established power production lines (e.g. on-shore wind). Any funding should be considered primarily as a means of political action, i.e. a measure not to meet today's short-term goals (eg quota requirement of certificate system) but to cut costs in order to reach the future (long term) goals. The offshore wind energy can be a very interesting candidate for such support, not least because of the favorable wind conditions that exist at sea. For these cost reductions to be realized, it is important to establish niche markets for the turbines and construction work that will be necessary. Such a technology policy presupposes a real development and not solely R and D and D projects. The report presents the results of previous research that supports this assumption, but it makes no attempt to assess whether the relevant effects are sufficient or not. However, it is important to indicate that a technology policy focused on offshore wind power is unlikely to be economically justified from a strictly national perspective, but should largely seen as a way for Sweden to take international responsibility in climate and energy policy. The instruments analyzed are: (a) higher share certificates for offshore wind in the certificate system: (b) increased pilot project support, (c) continued eco bonus and/or increased environmental bonus, (d) take over the cost of power system connection and any reinforcements, (e) feed-in tariffs (f) tender on designated locations; (g) the tender in which the operator selects an appropriate place; (h) investment; and (i) net interest income. These instruments are analyzed based on the following criteria; cost, technology development, expansion rate, the burden on state budget long-term and stable rules, simplification, and industrial policy objectives. The judgments made should be considered primarily as a discussion paper rather than as an overall assessment of the efficacy of control. A important conclusion is that the instruments should be introduced to ensure stable conditions for a continuous expansion, and the assessment is that the feed-in tariffs and tender may be interesting candidates for such aid. A series of outstanding issues remain regarding such design of these instruments, and these should be explored further in-depth study

  6. Absorbed Doses to Patients in Nuclear Medicine; Doskatalogen foer nukleaermedicin

    Energy Technology Data Exchange (ETDEWEB)

    Leide-Svegborn, Sigrid; Mattsson, Soeren; Nosslin, Bertil [Universitetssjukhuset MAS, Malmoe (Sweden). Avd. foer radiofysik; Johansson, Lennart [Norrlands Universitetssjukhus, Umeaa (Sweden). Avd. foer radiofysik

    2004-09-01

    The work with a Swedish catalogue of radiation absorbed doses to patients undergoing nuclear medicine investigations has continued. After the previous report in 1999, biokinetic data and dose estimates (mean absorbed dose to various organs and tissues and effective dose) have been produced for a number of substances: {sup 11}C- acetate, {sup 11}C- methionine, {sup 18}F-DOPA, whole antibody labelled with either {sup 99m}Tc, {sup 111}In, {sup 123}I or {sup 131}I, fragment of antibody, F(ab'){sub 2} labelled with either {sup 99m}Tc, {sup 111}In, {sup 123}I or {sup 131}I and fragment of antibody, Fab' labelled with either {sup 99m}Tc, {sup 111}In, {sup 123}I or {sup 131}I. The absorbed dose estimates for these substances have been made from published biokinetic information. For other substances of interest, e.g. {sup 14}C-urea (children age 3-6 years), {sup 14}C-glycocholic acid, {sup 14}C-xylose and {sup 14}C-triolein, sufficient literature data have not been available. Therefore, a large number of measurements on patients and volunteers have been carried out, in order to determine the biokinetics and dosimetry for these substances. Samples of breast milk from 50 mothers, who had been subject to nuclear medicine investigations, have been collected at various times after administration of the radiopharmaceutical to the mother. The activity concentration in the breast milk samples has been measured. The absorbed dose to various organs and tissues and the effective dose to the child who ingests the milk have been determined for 17 different radiopharmaceuticals. Based on these results revised recommendations for interruption of breast-feeding after nuclear medicine investigations are suggested.

  7. Changed market conditions for biogas production; Foeraendrade marknadsvillkor foer biogasproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Colnerud Granstroem, Sigrid; Gaaverud, Henrik; Glimhall, Alexandra

    2010-10-15

    The Swedish gas market consists mainly of the natural gas network that extends through the southwestern Sweden, and the local biogas markets. Biogas share of the Swedish gas market is growing steadily. The fact that the Swedish gas net is limited and fragmented forms an obstacle for biogas use to expand. That the gas market as a whole, natural gas included, must develop and expand is therefore a prerequisite for the large potential for Swedish Biogas to be realized. This in contrast with the ultimate objective to completely replace natural gas in the Swedish gas market. When policy changes are made in order to support biogas it is crucial for long-term competitiveness of biogas that these changes should not impact the natural gas market and hinder its development. Such a scenario would ultimately mean that also biogas development opportunities deteriorate. Biogas operations encounter three main problems that prevent or impede its expansion in the gas market. First, the potential for profitability in biogas production must be enhanced. Second, natural gas and biogas markets should be more integrated with each other. Thirdly, the biogas must be distributed in a cost-effective manner. The present investigation aims to supplement the Natural Gas Act with special provisions which takes into account the input and transmission of biogas. In addition to the production of biogas, it is now the producer's responsibility to clean the gas from water vapor, hydrogen sulfide and carbon dioxide and to augment the calorific value of the gas to the standard of Danish natural gas quality by propane addition and to ensure that the physical connection to network is available. There are thus a number of options available for shifting demarcation between biogas production and network operations. Short-term competitiveness of biogas would be strengthened most if purification and spiking the gas with propane and the connection to the network was imposed on network owners. In the longer term, it is not obvious that such a change would be beneficial for biogas as such a change could have long term adverse effects on the competitiveness of natural gas against other energy sources. The Energy Market Inspectorate has decided, therefore, not as desirable for the network owner to have responsibility for treatment or network connection. EI therefore considers that it is reasonable that the responsibility for propane spiking is imposed on the network operators. Network owner may then also able to refrain from propane spiking of the biogas and instead lower the heating value of the Danish natural gas - an attractive alternative if natural gas imports from other countries would be under consideration

  8. Units for radiation protection work; Storheter foer straalskyddsarbete

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, L

    1997-06-01

    ICRU has defined special measurable (operational) quantities for radiation protection. A consequence of using the operational quantities is that hand-held and personal dosemeters can give different measuring results in the same radiation situation. The differences vary and are caused by the geometry of the radiation field. The units have well documented relations to e.g. the ICRP effective dose and equivalent dose to an organ or tissue. Therefore, it is possible to estimate these doses from a measured value of e.g. the ambient dose equivalent. ICRU and ICRP have recently reviewed these relations in two important commonly issued reports (Report 57 and Publication 74). This report tries to show the value of understanding these units and their relations and is primarily meant to be used for educational purposes. 11 refs.

  9. Biomass Gasifier for Computer Simulation; Biomassa foergasare foer Computer Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Hansson, Jens; Leveau, Andreas; Hulteberg, Christian [Nordlight AB, Limhamn (Sweden)

    2011-08-15

    This report is an effort to summarize the existing data on biomass gasifiers as the authors have taken part in various projects aiming at computer simulations of systems that include biomass gasification. Reliable input data is paramount for any computer simulation, but so far there is no easy-accessible biomass gasifier database available for this purpose. This study aims at benchmarking current and past gasifier systems in order to create a comprehensive database for computer simulation purposes. The result of the investigation is presented in a Microsoft Excel sheet, so that the user easily can implement the data in their specific model. In addition to provide simulation data, the technology is described briefly for every studied gasifier system. The primary pieces of information that are sought for are temperatures, pressures, stream compositions and energy consumption. At present the resulting database contains 17 gasifiers, with one or more gasifier within the different gasification technology types normally discussed in this context: 1. Fixed bed 2. Fluidised bed 3. Entrained flow. It also contains gasifiers in the range from 100 kW to 120 MW, with several gasifiers in between these two values. Finally, there are gasifiers representing both direct and indirect heating. This allows for a more qualified and better available choice of starting data sets for simulations. In addition to this, with multiple data sets available for several of the operating modes, sensitivity analysis of various inputs will improve simulations performed. However, there have been fewer answers to the survey than expected/hoped for, which could have improved the database further. However, the use of online sources and other public information has to some extent counterbalanced the low response frequency of the survey. In addition to that, the database is preferred to be a living document, continuously updated with new gasifiers and improved information on existing gasifiers.

  10. Absorbed Doses to Patients in Nuclear Medicine; Doskatalogen foer nukleaermedicin

    Energy Technology Data Exchange (ETDEWEB)

    Leide-Svegborn, Sigrid; Mattsson, Soeren; Johansson, Lennart; Fernlund, Per; Nosslin, Bertil

    2007-04-15

    The Swedish radiation protection authority, (SSI), has supported work on estimates of radiation doses to patients from nuclear medicine examinations since more than 20 years. A number of projects have been reported. The results are put together and published under the name 'Doskatalogen' which contains data on doses to different organs and tissues from radiopharmaceuticals used for diagnostics and research. This new report contains data on: {sup 11}C-labelled substances (realistic maximum model), amino acids labelled with {sup 11}C, {sup 18}F or {sup 75}Se, {sup 99m}Tc-apcitide, {sup 123}I-labelled fatty acids ({sup 123}I- BMIPP and {sup 123}I-IPPA) and revised models for previously reported {sup 15}O-labelled water, {sup 99m}Tc-tetrofosmin (rest as well as exercise) and {sup 201}Tl-ion Data for almost 200 substances and radionuclides are included in the 'Doskatalogen' today. Since the year 2001 the 'Doskatalogen' is available on the authority's home page (www.ssi.se)

  11. Multinationals and plant survival

    DEFF Research Database (Denmark)

    Bandick, Roger

    2010-01-01

    The aim of this paper is twofold: first, to investigate how different ownership structures affect plant survival, and second, to analyze how the presence of foreign multinational enterprises (MNEs) affects domestic plants’ survival. Using a unique and detailed data set on the Swedish manufacturing...... sector, I am able to separate plants into those owned by foreign MNEs, domestic MNEs, exporting non-MNEs, and purely domestic firms. In line with previous findings, the result, when conditioned on other factors affecting survival, shows that foreign MNE plants have lower survival rates than non......-MNE plants. However, separating the non-MNEs into exporters and non-exporters, the result shows that foreign MNE plants have higher survival rates than non-exporting non-MNEs, while the survival rates of foreign MNE plants and exporting non-MNE plants do not seem to differ. Moreover, the simple non...

  12. Plant life management

    International Nuclear Information System (INIS)

    Charbonneau, S.; Framatome, J.B.

    1992-01-01

    Plant life assessment and extension studies have been performed by numerous companies all over the world. Critical equipment has been identified as well as various degradation mechanisms involved in the plant aging process. Nowadays one has to think what to implement to improve the existing situation in the Nuclear Power Plant (NPP). FRAMATOME has undertaken this thought process in order to find the right answers and bring them to utilities facing either critical concern for plant life extension or the problem of management of power plant potential longevity. This is why we prepared a Plant Life Improvement Action Plan, comprising 10 (ten) major items described hereafter using examples of work performed by FRAMATOME for its utility customers desiring to manage the lives of their plants, both in France with EDF and abroad

  13. Photochemical smog and plants

    Energy Technology Data Exchange (ETDEWEB)

    Sawada, T.

    1974-07-01

    Surveys of plant damage due to photochemical smog are summarized. The components of smog which appear to be responsible for plant damage include ozone and peroxyacyl nitrates. Their phytotoxic effects are much greater than those due to sulfur oxides. Damage surveys since 1970 reveal the following symptoms appearing on herbaceous plants (morning glory, cocks comb, dahlia, knotweed, petunia, chickweed, Welsh onion, spinach, Chinese cabbage, chard, taro): yellowish-white leaf discoloration, white and brown spots on matured leaves, and silvering of the lower surfaces of young leaves. Symptoms which appear on arboraceous plants such as zelkova, poplar, ginkgo, planetree, rose mallow, magnolia, pine tree, and rhododendron include early yellowing and reddening, white or brown spots, and untimely leaf-fall. The above plants are now utilized as indicator plants of photochemical smog. Surveys covering a broad area of Tokyo and three other prefectures indicate that plant damage due to photochemical smog extends to relatively unpolluted areas.

  14. Plant Physiology and Development

    DEFF Research Database (Denmark)

    Taiz, Lincoln; Zeiger, Eduardo; Møller, Ian Max

    Throughout its twenty-two year history, the authors of Plant Physiology have continually updated the book to incorporate the latest advances in plant biology and implement pedagogical improvements requested by adopters. This has made Plant Physiology the most authoritative, comprehensive......, and widely used upper-division plant biology textbook. In the Sixth Edition, the Growth and Development section (Unit III) has been reorganized and expanded to present the complete life cycle of seed plants from germination to senescence. In recognition of this enhancement, the text has been renamed Plant...... Physiology and Development. As before, Unit III begins with updated chapters on Cell Walls and Signals and Signal Transduction. The latter chapter has been expanded to include a discussion of major signaling molecules, such as calcium ions and plant hormones. A new, unified chapter entitled Signals from...

  15. Reassessing apoptosis in plants.

    Science.gov (United States)

    Dickman, Martin; Williams, Brett; Li, Yurong; de Figueiredo, Paul; Wolpert, Thomas

    2017-10-01

    Cell death can be driven by a genetically programmed signalling pathway known as programmed cell death (PCD). In plants, PCD occurs during development as well as in response to environmental and biotic stimuli. Our understanding of PCD regulation in plants has advanced significantly over the past two decades; however, the molecular machinery responsible for driving the system remains elusive. Thus, whether conserved PCD regulatory mechanisms include plant apoptosis remains enigmatic. Animal apoptotic regulators, including Bcl-2 family members, have not been identified in plants but expression of such regulators can trigger or suppress plant PCD. Moreover, plants exhibit nearly all of the biochemical and morphological features of apoptosis. One difference between plant and animal PCD is the absence of phagocytosis in plants. Evidence is emerging that the vacuole may be key to removal of unwanted plant cells, and may carry out functions that are analogous to animal phagocytosis. Here, we provide context for the argument that apoptotic-like cell death occurs in plants.

  16. Safe genetically engineered plants

    Energy Technology Data Exchange (ETDEWEB)

    Rosellini, D; Veronesi, F [Dipartimento di Biologia Vegetale e Biotecnologie Agroambientali e Zootecniche, Universita degli Studi di Perugia, Borgo XX giugno 74, 06121 Perugia (Italy)

    2007-10-03

    The application of genetic engineering to plants has provided genetically modified plants (GMPs, or transgenic plants) that are cultivated worldwide on increasing areas. The most widespread GMPs are herbicide-resistant soybean and canola and insect-resistant corn and cotton. New GMPs that produce vaccines, pharmaceutical or industrial proteins, and fortified food are approaching the market. The techniques employed to introduce foreign genes into plants allow a quite good degree of predictability of the results, and their genome is minimally modified. However, some aspects of GMPs have raised concern: (a) control of the insertion site of the introduced DNA sequences into the plant genome and of its mutagenic effect; (b) presence of selectable marker genes conferring resistance to an antibiotic or an herbicide, linked to the useful gene; (c) insertion of undesired bacterial plasmid sequences; and (d) gene flow from transgenic plants to non-transgenic crops or wild plants. In response to public concerns, genetic engineering techniques are continuously being improved. Techniques to direct foreign gene integration into chosen genomic sites, to avoid the use of selectable genes or to remove them from the cultivated plants, to reduce the transfer of undesired bacterial sequences, and make use of alternative, safer selectable genes, are all fields of active research. In our laboratory, some of these new techniques are applied to alfalfa, an important forage plant. These emerging methods for plant genetic engineering are briefly reviewed in this work.

  17. Safe genetically engineered plants

    International Nuclear Information System (INIS)

    Rosellini, D; Veronesi, F

    2007-01-01

    The application of genetic engineering to plants has provided genetically modified plants (GMPs, or transgenic plants) that are cultivated worldwide on increasing areas. The most widespread GMPs are herbicide-resistant soybean and canola and insect-resistant corn and cotton. New GMPs that produce vaccines, pharmaceutical or industrial proteins, and fortified food are approaching the market. The techniques employed to introduce foreign genes into plants allow a quite good degree of predictability of the results, and their genome is minimally modified. However, some aspects of GMPs have raised concern: (a) control of the insertion site of the introduced DNA sequences into the plant genome and of its mutagenic effect; (b) presence of selectable marker genes conferring resistance to an antibiotic or an herbicide, linked to the useful gene; (c) insertion of undesired bacterial plasmid sequences; and (d) gene flow from transgenic plants to non-transgenic crops or wild plants. In response to public concerns, genetic engineering techniques are continuously being improved. Techniques to direct foreign gene integration into chosen genomic sites, to avoid the use of selectable genes or to remove them from the cultivated plants, to reduce the transfer of undesired bacterial sequences, and make use of alternative, safer selectable genes, are all fields of active research. In our laboratory, some of these new techniques are applied to alfalfa, an important forage plant. These emerging methods for plant genetic engineering are briefly reviewed in this work

  18. [Intoxications with plants].

    Science.gov (United States)

    Kupper, Jacqueline; Reichert, Cornelia

    2009-05-01

    Ingestions of plants rarely lead to life-threatening intoxications. Highly toxic plants, which can cause death, are monkshood (Aconitum sp.), yew (Taxus sp.) and autumn crocus (Colchicum autumnale). Lethal ingestions of monkshood and yew are usually suicides, intoxications with autumn crocus are mostly accidental ingestions of the leaves mistaken for wild garlic (Allium ursinum). Severe intoxications can occur with plants of the nightshade family like deadly nightshade (Atropa belladonna), angel's trumpet (Datura suaveolens) or jimsonweed (Datura stramonium). These plants are ingested for their psychoactive effects. Ingestion of plant material by children most often only causes minor symptoms or no symptoms at all, as children usually do not eat great quantities of the plants. They are especially attracted by the colorful berries. There are plants with mostly cardiovascular effects like monkshood, yew and Digitalis sp. Some of the most dangerous plants belong to this group. Plants of the nightshade family cause an anticholinergic syndrome. With golden chain (Laburnum anagyroides), castor bean (Ricinus communis) and raw beans (Phaseolus vulgaris) we see severe gastrointestinal effects. Autumn crocus contains a cell toxin, colchicine, which leads to multiorgan failure. Different plants are irritative or even caustic to the skin. Treatment is usually symptomatic. Activated charcoal is administered within one hour after ingestion (1 g/kg). Endoscopic removal of plant material can be considered with ingestions of great quantities of highly toxic plants. Administration of repeated doses of charcoal (1-2 g/h every 2-4 hours) may be effective in case of oleander poisoning. There exist only two antidotes: Anti-digoxin Fab fragments can be used with cardenolide glycoside-containing plants (Digitalis sp., Oleander). Physostigmine is the antidote for severe anticholinergic symptoms of the CNS. Antibodies against colchicine, having been developed in France, are not available at

  19. Opportunity and potential for fuel cell systems for energy in buildings; Moejlighet och potential foer braenslecellsystem foer energifoersoerjning i byggnader

    Energy Technology Data Exchange (ETDEWEB)

    Jannasch, Anna-Karin (Catator AB (Sweden))

    2011-04-15

    While planning for new sustainable and environmentally friendly communities in Sweden, discussions on using fuel cells for small-scale power and heat production (mCHP) are today on-going. Examples of such communities are Sege Park in Malmoe and Norra Djurgardsstaden in Stockholm, where several members of the Swedish Construction Industry's Organisation for Research and Development (SBUF) are participating in the development. The status and the potential of using fuel cell based mCHP compared to conventional heat and power production technology and other mCHP-technologies (Internal combustion engine (ICE), Stirling) is today therefore a very interesting question for both the energy and the building sector, who also ask for more knowledge within the field. This work focuses on this purpose. The main goals of this report are: 1. To give an overall description of different existing fuel cell technologies and necessary belonging system components. The fuel cell systems are discussed and evaluated based on parameters such as efficiencies, fuel flexibility, life-time, complexity, maturity and cost. The systems are compared to mCHPs based on small heat engines (Internal combustion, Stirling). 2. To give a state-of-the-art report on fuel cell based mCHPs and to describe possibilities and risks related to different technologies. 3. To guideline for future choices of system solutions suitable for different building constructions and different geographical placements. The work is limited to systems suitable for small houses (< 5 kWe) and larger residential buildings (< 50 kWe) situated in population centres/cities where infra-structures for natural gas/biogas and the national grid are available. The project has been performed by Catator AB on the request of SBUF with support from the Swedish Gas Centre (SGC AB), Skanska and Catator. The study is based on the open literature, the information given by leading fuel cell system suppliers and Catator's own knowledge and experience in the field. Today, there are in general three different fuel cell technologies that are in focus for mCHPs: Low and high temperature polymer electrolyte fuel cells (LT/HT-PEMFC) and solid oxide fuel cells (SOFC). Among these, LT-PEMFC is the most mature technology and is therefore today dominating the market (80 %). As reforming method, steam reforming with downstream atmospheric gas clean-up is the most commonly applied since this is the method resulting in the highest efficiency. In the near future, LT-PEMFC is expected to be replaced by the less mature SOFC, since the use of the latter technology opens up for significant system simplifications, higher electrical efficiencies (40-45 % instead of 30-35 %) and more efficient heat recovering. Japan is by far the world's leading country in the development and the distribution of fuel cell based mCHPs. In EU, the development in Great Britain and Germany are dominating the market. In Sweden, only three different fuel based mCHPs have been installed and tested so far. Two of those were placed in Hammarby Sjoestad in Stockholm during the period 2002-2008. The third one, called ComfortPower, was developed by Catator during 2010 and is hybridised with a heat pump module. In Japan, there are today almost 6000 fuel based mCHPs installed and in operation in private houses and public buildings. Since May 2009, there is a approx1 kWe/2 kWth commercially available system, called ENE-FARM, for operation on either natural gas/LPG/kerosene. Results such as 35-45 % and 85-90 % in electrical and total system efficiency, respectively, in combination with promising life-time data, i.e. approx 0.5-1 % degradation during almost 20 000 hours operation, have been achieved. The big remaining challenge is the cost. Today, the price of ENE-FARM is 210 kSEK without subsidies. The cost and hence so also the price is however expected to drastically decrease with on-going stack and components improvements and increasing production volumes. In year 2015, the price is expected to be around 40-60 kSEK, i.e in the same range as corresponding ICE-based mCHPs cost today, provided that the production volume reaches around 100 000 units/year/supplier. Similar results and predictions have been reported from leading system suppliers in EU. The market potential for mCHPs is strongly dependent on the geographical placement.

  20. Indicators and calculation methods for monitoring policy for energy efficiency; Indikatorer och beraekningsmetoder foer att foelja upp politik foer energieffektivisering

    Energy Technology Data Exchange (ETDEWEB)

    2011-07-01

    Energy efficiency objectives can be absolute or relative. With absolute objectives the energy use of a given year should be at a certain level, for example, 80 percent of today's energy use. With a relatively objective energy use should be related to something else such as gross domestic production (GDP) or gross national income (GNI). Depending on how the goals are formulated the requirements of the policy instruments introduced to contribute to the achievement of objectives will vary. In addition to the Energy Services Directive objective (Directive 2006/32/EC) an objective has been set for the EU which means that energy consumption in 2020 will be 20 percent more efficient compared to a reference scenario. Estimates of the impact analysis of the EU Action Plan for energy efficiency 2011 indicates that the EU's energy input for energy purposes should be a maximum of 1474 Mtoe. The savings compared to the energy use reference scenario which are projected to be 1842 Mtoe will thus amount to 368 Mtoe in 2020. There are reasons to pay attention to the definition of key terms. Energy conservation and energy efficiency for example are used in a number of non synonymous ways even in EU documents. It has consequences including the interpretation of the objective. Sweden has set an objective to reduce energy intensity in terms of energy input in relation to GDP by 20 percent by the year 2020 with 2008 as base year. Sweden's intensity objective takes, unlike the EU's energy efficiency objective, account of the actual economic development. EU's energy efficiency objective is based on a forecast of the economic development. Sweden also has an objective of energy consumption per square meter of residential and commercial buildings. It should be reduced by 20 percent by 2020 and by 50 percent by 2050. Furthermore, there is a focus that energy efficiency in transport must improve in order to contribute to the environmental objective of reduced climate impact. EU's energy efficiency objective is not currently mandatory and has not yet been distributed. It is therefore also unclear how the monitoring should be done, but a starting point might be to monitor countries' contribution to the objective through a set of indicators

  1. Nuclear power plants

    International Nuclear Information System (INIS)

    Margulova, T.Ch.

    1976-01-01

    The textbook focuses on the technology and the operating characteristics of nuclear power plants equiped with pressurized water or boiling water reactors, which are in operation all over the world at present. The following topics are dealt with in relation to the complete plant and to economics: distribution and consumption of electric and thermal energy, types and equipment of nuclear power plants, chemical processes and material balance, economical characteristics concerning heat and energy, regenerative preheating of feed water, degassing and condenser systems, water supply, evaporators, district heating systems, steam generating systems and turbines, coolant loops and pipes, plant siting, ventilation and decontamination systems, reactor operation and management, heat transfer including its calculation, design of reactor buildings, and nuclear power plants with gas or sodium cooled reactors. Numerous technical data of modern Soviet nuclear power plants are included. The book is of interest to graduate and post-graduate students in the field of nuclear engineering as well as to nuclear engineers

  2. Conditional sterility in plants

    Science.gov (United States)

    Meagher, Richard B.; McKinney, Elizabeth; Kim, Tehryung

    2010-02-23

    The present disclosure provides methods, recombinant DNA molecules, recombinant host cells containing the DNA molecules, and transgenic plant cells, plant tissue and plants which contain and express at least one antisense or interference RNA specific for a thiamine biosynthetic coding sequence or a thiamine binding protein or a thiamine-degrading protein, wherein the RNA or thiamine binding protein is expressed under the regulatory control of a transcription regulatory sequence which directs expression in male and/or female reproductive tissue. These transgenic plants are conditionally sterile; i.e., they are fertile only in the presence of exogenous thiamine. Such plants are especially appropriate for use in the seed industry or in the environment, for example, for use in revegetation of contaminated soils or phytoremediation, especially when those transgenic plants also contain and express one or more chimeric genes which confer resistance to contaminants.

  3. Plant synthetic biology.

    Science.gov (United States)

    Liu, Wusheng; Stewart, C Neal

    2015-05-01

    Plant synthetic biology is an emerging field that combines engineering principles with plant biology toward the design and production of new devices. This emerging field should play an important role in future agriculture for traditional crop improvement, but also in enabling novel bioproduction in plants. In this review we discuss the design cycles of synthetic biology as well as key engineering principles, genetic parts, and computational tools that can be utilized in plant synthetic biology. Some pioneering examples are offered as a demonstration of how synthetic biology can be used to modify plants for specific purposes. These include synthetic sensors, synthetic metabolic pathways, and synthetic genomes. We also speculate about the future of synthetic biology of plants. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Annual Plant Reviews

    DEFF Research Database (Denmark)

    , three dimensional structures and functions of each protein in a biological system. In plant science, the number of proteome studies is rapidly expanding after the completion of the Arabidopsis thaliana genome sequence, and proteome analyses of other important or emerging model systems and crop plants...... are in progress or are being initiated. Proteome analysis in plants is subject to the same obstacles and limitations as in other organisms, but the nature of plant tissues, with their rigid cell walls and complex variety of secondary metabolites, means that extra challenges are involved that may not be faced when...... analysing other organisms. This volume aims to highlight the ways in which proteome analysis has been used to probe the complexities of plant biochemistry and physiology. It is aimed at researchers in plant biochemistry, genomics, transcriptomics and metabolomics who wish to gain an up-to-date insight...

  5. Towards plant wires

    OpenAIRE

    Adamatzky, Andrew

    2014-01-01

    In experimental laboratory studies we evaluate a possibility of making electrical wires from living plants. In scoping experiments we use lettuce seedlings as a prototype model of a plant wire. We approximate an electrical potential transfer function by applying direct current voltage to the lettuce seedlings and recording output voltage. We analyse oscillation frequencies of the output potential and assess noise immunity of the plant wires. Our findings will be used in future designs of self...

  6. Design of chemical plant

    International Nuclear Information System (INIS)

    Lee, Dong Il; Kim, Seung Jae; Yang, Jae Ho; Ryu, Hwa Won

    1993-01-01

    This book describes design of chemical plant, which includes chemical engineer and plan for chemical plant, development of chemical process, cost engineering pattern, design and process development, general plant construction plan, project engineering, foundation for economy on assets and depreciation, estimation for cost on capital investment and manufacturing cost, design with computers optimal design and method like fluid mechanics design chemical device and estimation for cost, such as dispatch of material and device writing on design report and appendixes.

  7. Late Palaeozoic plants.

    Science.gov (United States)

    Feng, Zhuo

    2017-09-11

    Land plants are one of the major constituents of terrestrial ecosystems on Earth, and play an irreplaceable role in human activities today. If we are to understand the extant plants, it is imperative that we have some understanding of the fossil plants from the deep geological past, particularly those that occurred during their early evolutionary history, in the late Palaeozoic. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Plant Habitat (PH)

    Science.gov (United States)

    Onate, Bryan

    2016-01-01

    The International Space Station (ISS) will soon have a platform for conducting fundamental research of Large Plants. Plant Habitat (PH) is designed to be a fully controllable environment for high-quality plant physiological research. PH will control light quality, level, and timing, temperature, CO2, relative humidity, and irrigation, while scrubbing ethylene. Additional capabilities include leaf temperature and root zone moisture and oxygen sensing. The light cap will have red (630 nm), blue (450 nm), green (525 nm), far red (730 nm) and broad spectrum white LEDs. There will be several internal cameras (visible and IR) to monitor and record plant growth and operations.

  9. Integrated Nuclear Recycle Plant

    International Nuclear Information System (INIS)

    Patodi, Anuj; Parashar, Abhishek; Samadhiya, Akshay K.; Ray, Saheli; Dey, Mitun; Singh, K.K.

    2017-01-01

    Nuclear Recycle Board (NRB), Tarapur proposes to set up an 'Integrated Nuclear Recycle Plant' at Tarapur. This will be located in the premises of BARC facilities. The project location is at coastal town of Tarapur, 130 Km north of Mumbai. Project area cover of INRP is around 80 hectares. The plant will be designed to process spent fuel received from Pressurized Heavy Water Reactors (PHWRs). This is the first large scale integrated plant of the country. INRP will process spent fuel obtained from indigenous nuclear power plants and perform left over nuclear waste disposal

  10. Towards plant wires.

    Science.gov (United States)

    Adamatzky, Andrew

    2014-08-01

    In experimental laboratory studies we evaluate a possibility of making electrical wires from living plants. In scoping experiments we use lettuce seedlings as a prototype model of a plant wire. We approximate an electrical potential transfer function by applying direct current voltage to the lettuce seedlings and recording output voltage. We analyse oscillation frequencies of the output potential and assess noise immunity of the plant wires. Our findings will be used in future designs of self-growing wetware circuits and devices, and integration of plant-based electronic components into future and emergent bio-hybrid systems. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  11. MBS Native Plant Communities

    Data.gov (United States)

    Minnesota Department of Natural Resources — This data layer contains results of the Minnesota County Biological Survey (MCBS). It includes polygons representing the highest quality native plant communities...

  12. The Kuroshio power plant

    CERN Document Server

    Chen, Falin

    2013-01-01

    By outlining a new design or the Kuroshio power plant, new approaches to turbine design, anchorage system planning, deep sea marine engineering and power plant operations and maintenance are explored and suggested. The impact on the local environment, particularly in the face of natural disasters, is also considered to provide a well rounded introduction to plan and build a 30MW pilot power plant. Following a literature review, the six chapters of this book propose a conceptual design by focusing on the plant's core technologies and establish the separate analysis logics for turbine design and

  13. Plant Transporter Identification

    DEFF Research Database (Denmark)

    Larsen, Bo

    Membrane transport proteins (transporters) play a critical role for numerous biological processes, by controlling the movements of ions and molecules in and out of cells. In plants, transporters thus function as gatekeepers between the plant and its surrounding environment and between organs......, tissues, cells and intracellular compartments. Since plants are highly compartmentalized organisms with complex transportation infrastructures, they consequently have many transporters. However, the vast majority of predicted transporters have not yet been experimentally verified to have transport...... activity. This project contains a review of the implemented methods, which have led to plant transporter identification, and present our progress on creating a high-throughput functional genomics transporter identification platform....

  14. Less power plants

    International Nuclear Information System (INIS)

    TASR

    2003-01-01

    In the Slovak Republic the number of company power plants decreased as against 2001 by two sources. In present time only 35 companies have their own power plants. The companies Slovnaft, Kappa Sturovo, Slovensky hodvab Senica, Matador Puchov, Maytex Liptovsky MikuIas, Kovohuty Krompachy, Chemko Strazske and some Slovak sugar factories belong to the largest company power plants in force of distributing companies. Installed output of present 35 company sources is 531 MW. The largest of separate power plants as Paroplynovy cyklus Bratislava (218 MW) and VD Zilina (72 MW) belong to independent sources. Total installed output of Slovak sources was 8306 MW in the end of last year

  15. Offshore atomic power plants

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    Various merits of offshore atomic power plants are illustrated, and their systems are assessed. The planning of the offshore atomic power plants in USA is reviewed, and the construction costs of the offshore plant in Japan were estimated. Air pollution problem may be solved by the offshore atomic power plants remarkably. Deep water at low temperature may be advantageously used as cooling water for condensers. Marine resources may be bred by building artificial habitats and by providing spring-up equipments. In the case of floating plants, the plant design can be standardized so that the construction costs may be reduced. The offshore plants can be classified into three systems, namely artificial island system, floating system and sea bottom-based system. The island system may be realized with the present level of civil engineering, but requires the development of technology for the resistance of base against earthquake and its calculation means. The floating system may be constructed with conventional power plant engineering and shipbuilding engineering, but the aseismatic stability of breakwater may be a problem to be solved. Deep water floating system and deep water submerging system are conceivable, but its realization may be difficult. The sea bottom-based system with large caissons can be realized by the present civil engineering, but the construction of the caissons, stability against earthquake and resistance to waves may be problems to be solved. The technical prediction and assessment of new plant sites for nuclear power plants have been reported by Science and Technology Agency in 1974. The construction costs of an offshore plant has been estimated by the Ministry of International Trade and Industry to be yen71,026/kW as of 1985. (Iwakiri, K.)

  16. Selenium accumulation by plants

    Science.gov (United States)

    White, Philip J.

    2016-01-01

    Background Selenium (Se) is an essential mineral element for animals and humans, which they acquire largely from plants. The Se concentration in edible plants is determined by the Se phytoavailability in soils. Selenium is not an essential element for plants, but excessive Se can be toxic. Thus, soil Se phytoavailability determines the ecology of plants. Most plants cannot grow on seleniferous soils. Most plants that grow on seleniferous soils accumulate 100 mg Se kg–1 dry matter. These plants are considered to be Se accumulators. Some species can even accumulate Se concentrations of 1000–15 000 mg Se kg–1 dry matter and are called Se hyperaccumulators. Scope This article provides an overview of Se uptake, translocation and metabolism in plants and highlights the possible genetic basis of differences in these between and within plant species. The review focuses initially on adaptations allowing plants to tolerate large Se concentrations in their tissues and the evolutionary origin of species that hyperaccumulate Se. It then describes the variation in tissue Se concentrations between and within angiosperm species and identifies genes encoding enzymes limiting the rates of incorporation of Se into organic compounds and chromosomal loci that might enable the development of crops with greater Se concentrations in their edible portions. Finally, it discusses transgenic approaches enabling plants to tolerate greater Se concentrations in the rhizosphere and in their tissues. Conclusions The trait of Se hyperaccumulation has evolved several times in separate angiosperm clades. The ability to tolerate large tissue Se concentrations is primarily related to the ability to divert Se away from the accumulation of selenocysteine and selenomethionine, which might be incorporated into non-functional proteins, through the synthesis of less toxic Se metabilites. There is potential to breed or select crops with greater Se concentrations in their edible tissues, which

  17. Better Plants Program Overview

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-09-30

    The U.S. Department of Energy’s (DOE’s) Better Buildings, Better Plants Program is a voluntary partnership initiative to drive significant energy efficiency improvement across energy intensive companies and organizations. 157 leading manufacturers and public water and wastewater treatment utilities are partnering with DOE through Better Plants to improve energy efficiency, slash carbon emissions, and cut energy costs.

  18. Plant Glandular Trichomes

    Indian Academy of Sciences (India)

    landing on the plant. Glandular trichomes in catmint (Nepeta sp.) produce nepetalactone, closely related to the aphid sex pheromone, nepetalactol. Nepetalactone can be reduced to the corresponding nepetalactol. ... Plant glandular trichomes function either as repositories or releasing sites of various chemicals. Interest in ...

  19. Plants as green phones

    NARCIS (Netherlands)

    Soler, R.; Harvey, J.A.; Bezemer, T.M.; Stuefer, J.F.

    2008-01-01

    Plants can act as vertical communication channels or `green phones¿ linking soil-dwelling insects and insects in the aboveground ecosystem. When root-feeding insects attack a plant, the direct defense system of the shoot is activated, leading to an accumulation of phytotoxins in the leaves. The

  20. Solar thermal power plants

    International Nuclear Information System (INIS)

    Schnatbaum, L.

    2009-01-01

    The solar thermal power plant technology, the opportunities it presents and the developments in the market are outlined. The focus is on the technology of parabolic trough power plants, a proven technology for solar power generation on a large scale. In a parabolic trough power plant, trough-shaped mirrors concentrate the solar irradiation onto a pipe in the focal line of the collector. The thermal energy thus generated is used for electricity generation in a steam turbine. Parabolic trough plants can be combined with thermal storage and fossil or biomass fired heat exchangers to generate electricity even when the sun is not shining. Solar Millennium AG in Erlangen has developed the first power plant of this kind in Europe. After two years of construction the plant started operation in Southern Spain in 2008. This one and its sister projects are important steps leading the way for the whole market. The paper also covers the technological challenges, the key components used and the research and development activities concerning this technology. Solar thermal power plants are ideal for covering peak and medium loads in power grids. In hybrid operation they can also cover base-load. The Solar Chimney power plant, another striking technology for the conversion of solar into electric energy, is described briefly. The paper concludes with a look at the future - the import of solar energy from the deserts of North Africa to central Europe. (author)

  1. Redox signaling in plants.

    Science.gov (United States)

    Foyer, Christine H; Noctor, Graham

    2013-06-01

    Our aim is to deliver an authoritative and challenging perspective of current concepts in plant redox signaling, focusing particularly on the complex interface between the redox and hormone-signaling pathways that allow precise control of plant growth and defense in response to metabolic triggers and environmental constraints and cues. Plants produce significant amounts of singlet oxygen and other reactive oxygen species (ROS) as a result of photosynthetic electron transport and metabolism. Such pathways contribute to the compartment-specific redox-regulated signaling systems in plant cells that convey information to the nucleus to regulate gene expression. Like the chloroplasts and mitochondria, the apoplast-cell wall compartment makes a significant contribution to the redox signaling network, but unlike these organelles, the apoplast has a low antioxidant-buffering capacity. The respective roles of ROS, low-molecular antioxidants, redox-active proteins, and antioxidant enzymes are considered in relation to the functions of plant hormones such as salicylic acid, jasmonic acid, and auxin, in the composite control of plant growth and defense. Regulation of redox gradients between key compartments in plant cells such as those across the plasma membrane facilitates flexible and multiple faceted opportunities for redox signaling that spans the intracellular and extracellular environments. In conclusion, plants are recognized as masters of the art of redox regulation that use oxidants and antioxidants as flexible integrators of signals from metabolism and the environment.

  2. Cognition in plants

    NARCIS (Netherlands)

    Calvo, P.; Keijzer, F.A.

    2009-01-01

    To what extent can plants be considered cognitive from the perspective of embodied cognition? Cognition is interpreted very broadly within embodied cognition, and the current evidence for plant intelligence might find an important theoretical background here. However, embodied cognition does stress

  3. Invertebrates and Plants

    Science.gov (United States)

    Wendell R. Haag; Robert J. Distefano; Siobhan Fennessy; Brett D. Marshall

    2013-01-01

    Invertebrates and plants are among the most ubiquitous and abundant macroscopic organisms in aquatic ecosystems; they dominate most habitats in both diversity and biomass and play central roles in aquatic food webs. Plants regulate and create habitats for a wide array of organisms (Cooke et al. 2005). Snail grazing and bivalve filtering profoundly alter habitats and...

  4. Modulating lignin in plants

    Science.gov (United States)

    Apuya, Nestor; Bobzin, Steven Craig; Okamuro, Jack; Zhang, Ke

    2013-01-29

    Materials and methods for modulating (e.g., increasing or decreasing) lignin content in plants are disclosed. For example, nucleic acids encoding lignin-modulating polypeptides are disclosed as well as methods for using such nucleic acids to generate transgenic plants having a modulated lignin content.

  5. Recognizing Plant Defense Priming

    NARCIS (Netherlands)

    Martinez-Medina, Ainhoa; Flors, Victor; Heil, Martin; Mauch-Mani, Brigitte; Pieterse, Corné M J|info:eu-repo/dai/nl/113115113; Pozo, Maria J; Ton, Jurriaan; van Dam, Nicole M; Conrath, Uwe

    2016-01-01

    Defense priming conditions diverse plant species for the superinduction of defense, often resulting in enhanced pest and disease resistance and abiotic stress tolerance. Here, we propose a guideline that might assist the plant research community in a consistent assessment of defense priming in

  6. Exotic invasive plants

    Science.gov (United States)

    Carolyn Hull Sieg; Barbara G. Phillips; Laura P. Moser

    2003-01-01

    Ecosystems worldwide are threatened by nonnative plant invasions that can cause undesirable, irreversible changes. They can displace native plants and animals, out-cross with native flora, alter nutrient cycling and other ecosystem functions, and even change an ecosystem's flammability (Walker and Smith 1997). After habitat loss, the spread of exotic species is...

  7. Plant-Fungus Marriages

    Indian Academy of Sciences (India)

    Every plant requires mineral elements for growth. A mnemonic ... lar coils. More commonly, the hypha forms highly branched, .... stamps on the edible and poisonous mushrooms (Figure 2). One of the ... but these days dogs are used for truffle. 'hunting' . .... example is a non-chlorophyllous plant known as Indian pipe or.

  8. Dormancy in Plant Seeds

    NARCIS (Netherlands)

    Hilhorst, H.W.M.; Finch-Savage, W.E.; Buitink, J.; Bolingue, W.; Leubner-Metzger, G.

    2010-01-01

    Seed dormancy has been studied intensely over the past decades and, at present, knowledge of this plant trait is at the forefront of plant biology. The main model species is Arabidopsis thaliana, an annual weed, possessing nondeep physiological dormancy. This overview presents the state-of-the-art

  9. Slavery in plants

    NARCIS (Netherlands)

    Kabiri, S.; Rodenburg, J.; Ast, van A.; Bastiaans, L.

    2017-01-01

    The rain-fed lowland rice weed Rhamphicarpa fistulosa (Rice Vampireweed) is a facultative root parasitic plant. Growth and reproduction of R. fistulosa benefit considerably from parasitism, but how this affects the host plant is not well established. We determined accumulation and partitioning of

  10. Power plant chemical technology

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    17 contributions covering topies of fossil fuel combustion, flue gas cleaning, power plant materials, corrosion, water/steam cycle chemistry, monitoring and control were presented at the annual meeting devoted to Power Plant Chemical Technology 1996 at Kolding (Denmark) 4-6 September 1996. (EG)

  11. Plant diagnosis device

    International Nuclear Information System (INIS)

    Tozuka, Shin-ichi.

    1996-01-01

    Standard data approximately defined are inputted as 1:1 functional data between at least two or more plant data and each of plant data are inputted. Diagnosis data corresponding to each of process data are formed based on the functional data. Limit value data to be a threshold value which determines whether the diagnosis data are in a predetermined state or not are formed. The diagnosis data and the limit value data are displayed in a recognizable state. If diagnosis data of a plurality of plants are displayed simultaneously, all of the plant data are substantially the same value with one standard datum if the plant is in a normal state. When abnormality should occur in the plant, the difference between the diagnosis data and the standard data is remarkable, and the difference between the diagnosis data of other normal plant data and the standard data are also made remarkably, accordingly, the display of a plurality of diagnosis data is scattered thereby capable of diagnosing the abnormality of the plant. (N.H.)

  12. Methylome evolution in plants

    NARCIS (Netherlands)

    Vidalis, Amaryllis; Živković, Daniel; Wardenaar, René; Roquis, David; Tellier, Aurélien; Johannes, Frank

    2016-01-01

    Despite major progress in dissecting the molecular pathways that control DNA methylation patterns in plants, little is known about the mechanisms that shape plant methylomes over evolutionary time. Drawing on recent intra- and interspecific epigenomic studies, we show that methylome evolution over

  13. Antimicrobial Peptides from Plants

    Directory of Open Access Journals (Sweden)

    James P. Tam

    2015-11-01

    Full Text Available Plant antimicrobial peptides (AMPs have evolved differently from AMPs from other life forms. They are generally rich in cysteine residues which form multiple disulfides. In turn, the disulfides cross-braced plant AMPs as cystine-rich peptides to confer them with extraordinary high chemical, thermal and proteolytic stability. The cystine-rich or commonly known as cysteine-rich peptides (CRPs of plant AMPs are classified into families based on their sequence similarity, cysteine motifs that determine their distinctive disulfide bond patterns and tertiary structure fold. Cystine-rich plant AMP families include thionins, defensins, hevein-like peptides, knottin-type peptides (linear and cyclic, lipid transfer proteins, α-hairpinin and snakins family. In addition, there are AMPs which are rich in other amino acids. The ability of plant AMPs to organize into specific families with conserved structural folds that enable sequence variation of non-Cys residues encased in the same scaffold within a particular family to play multiple functions. Furthermore, the ability of plant AMPs to tolerate hypervariable sequences using a conserved scaffold provides diversity to recognize different targets by varying the sequence of the non-cysteine residues. These properties bode well for developing plant AMPs as potential therapeutics and for protection of crops through transgenic methods. This review provides an overview of the major families of plant AMPs, including their structures, functions, and putative mechanisms.

  14. Nuclear Power Plants. Revised.

    Science.gov (United States)

    Lyerly, Ray L.; Mitchell, Walter, III

    This publication is one of a series of information booklets for the general public published by the United States Atomic Energy Commission. Among the topics discussed are: Why Use Nuclear Power?; From Atoms to Electricity; Reactor Types; Typical Plant Design Features; The Cost of Nuclear Power; Plants in the United States; Developments in Foreign…

  15. NUCLEAR POWER PLANT

    Science.gov (United States)

    Carter, J.C.; Armstrong, R.H.; Janicke, M.J.

    1963-05-14

    A nuclear power plant for use in an airless environment or other environment in which cooling is difficult is described. The power plant includes a boiling mercury reactor, a mercury--vapor turbine in direct cycle therewith, and a radiator for condensing mercury vapor. (AEC)

  16. Caladium plant poisoning

    Science.gov (United States)

    ... enough to prevent normal speaking and swallowing. Home Care If the plant was eaten, wipe out the mouth with a ... to Expect at the Emergency Room Take the plant with you to the hospital, if possible. The health care provider will measure and monitor the person's vital ...

  17. Gold in plants

    International Nuclear Information System (INIS)

    Girling, C.A.; Peterson, P.J.

    1980-01-01

    Many plants have the ability to take up gold from the soil and to accumulate it in their tisssue. Advances have been made in understanding these processes to the point where their exploitation in the field of prospecting for gold appears practically feasible. Neutron activation analysis is used for the determination of the small quantities of gold in plants

  18. Recognizing plant defense priming

    NARCIS (Netherlands)

    Martinez-Medina, A.; Flors, V.; Heil, M.; Mauch-Mani, B.; Pieterse, C.M.J.; Pozo, M.J.; Ton, J.; Van Dam, N.M.; Conrath, U.

    2016-01-01

    Defense priming conditions diverse plant species for the superinduction of defense, often resulting in enhanced pest and disease resistance and abiotic stress tolerance. Here, we propose a guideline that might assist the plant research community in a consistent assessment of defense priming in

  19. Carotenoid metabolism in plants

    Science.gov (United States)

    Carotenoids are mostly C40 terpenoids, a class of hydrocarbons that participate in various biological processes in plants, such as photosynthesis, photomorphogenesis, photoprotection, and development. Carotenoids also serve as precursors for two plant hormones and a diverse set of apocarotenoids. Th...

  20. [Neotropical plant morphology].

    Science.gov (United States)

    Pérez-García, Blanca; Mendoza, Aniceto

    2002-01-01

    An analysis on plant morphology and the sources that are important to the morphologic interpretations is done. An additional analysis is presented on all published papers in this subject by the Revista de Biología Tropical since its foundation, as well as its contribution to the plant morphology development in the neotropics.

  1. Automatic micropropagation of plants

    Science.gov (United States)

    Otte, Clemens; Schwanke, Joerg; Jensch, Peter F.

    1996-12-01

    Micropropagation is a sophisticated technique for the rapid multiplication of plants. It has a great commercial potential due to the speed of propagation, the high plant quality, and the ability to produce disease-free plants. However, micropropagation is usually done by hand which makes the process cost-intensive and tedious for the workers especially because it requires a sterile work-place. Therefore, we have developed a prototype automation system for the micropropagation of a grass species (miscanthus sinensis gigantheus). The objective of this paper is to describe the robotic system in an overview and to discuss the vision system more closely including the implemented morphological operations recognizing the cutting and gripping points of miscanthus plants. Fuzzy controllers are used to adapt the parameters of image operations on-line to each individual plant. Finally, we discuss our experiences with the developed prototype an give a preview of a possible real production line system.

  2. Plants and fluorine

    Energy Technology Data Exchange (ETDEWEB)

    Garber, K

    1962-01-01

    A report is given about the contents of fluorine in soil and different plants. It is stated that spinach and several spice herbages are rich in fluorine (0.98 - 21.8 ppm) while in other plants are not more than 5 ppm maximum. An exception is found in Thea sinensis with 178 ppm and more. Tea is, therefore, a source of fluorine for contamination of the human body. An increase of the fluorine contents of plants by manuring with F-salts or mineral manure is possible but of long duration. Damage to plants by uptake of fluorine from soil as well as in a gaseous condition from the atmosphere are described. The rate of damage is related to the type of soil in which the plant is grown.

  3. Poultry Plant Noise Control

    Science.gov (United States)

    1982-01-01

    A demonstration conducted last winter at the Tip Top Poultry Plant intended to show poultry plant managers from all over the U.S. potential solutions to the problem of plant noise. Plastic covers used over sound absorbing materials need to meet cleanability requirements, high- pressure water cleaning and other harsh maintenance procedures peculiar to the poultry processing industry. For the demonstration, Fiber Flex, Inc. manufactured and donated 750 noise panels; Owens-Corning Fiberglas Corporation donated the fiberglas cores; and the cover material was purchased from Howe and Bainbridge. The Engineering Experiment Station (EES) conducted before and after noise surveys and is evaluating the effect of noise reduction on turnover and productivity in the demonstration plant. EES plans to conduct a noise abatement workshop and update a handbook to help poultry processors with noise problems. EES study and demonstration may be applicable to other food processing plants where similar sanitary constraints exist.

  4. Protein carbonylation in plants

    DEFF Research Database (Denmark)

    Møller, Ian Max; Havelund, Jesper; Rogowska-Wrzesinska, Adelina

    2017-01-01

    This chapter provides an overview of the current knowledge on protein carbonylation in plants and its role in plant physiology. It starts with a brief outline of the turnover and production sites of reactive oxygen species (ROS) in plants and the causes of protein carbonylation. This is followed...... by a description of the methods used to study protein carbonylation in plants, which is also very brief as the methods are similar to those used in studies on animals. The chapter also focuses on protein carbonylation in plants in general and in mitochondria and in seeds in particular, as case stories where...... specific carbonylated proteins have been identified. Protein carbonylation appears to accumulate at all stages of seed development and germination investigated to date. In some cases, such as seed aging, it is probably simply an accumulation of oxidative damage. However, in other cases protein...

  5. Plant control device

    International Nuclear Information System (INIS)

    Sato, Masuo; Ono, Makoto.

    1995-01-01

    A plant control device comprises an intellectual instrumentation group for measuring a predetermined process amount, an intellectual equipment group operating in accordance with a self-countermeasure, a system information space for outputting system information, a system level monitoring and diagnosing information generalization section for outputting system information, a system level maintenance information generalization section for outputting information concerning maintenance, a plant level information space and a plant level information generalization section. Each of them determines a state of the plant autonomously, and when abnormality is detected, each of the intellectual instrumentation, equipments and systems exchange information with each other, to conduct required operations including operations of intellectual robots, as required. Appropriate countermeasures for gauges, equipments and systems can be conducted autonomously at a place where operators can not access to improve reliability of complicate operations in the working site, as well as improve plant safety and reliability. (N.H.)

  6. Plant abnormality inspection device

    International Nuclear Information System (INIS)

    Takenaka, Toshio.

    1990-01-01

    The present invention concerns a plant abnormality inspection device for conducting remote or automatic patrolling inspection in a plant and, more particularly, relates to such a device as capable of detecting abnormal odors. That is, the device comprises a moving device for moving to a predetermined position in the plant, a plurality of gas sensors for different kind of gases to be inspected mounted thereon, a comparator for comparing the concentration of a gas detected by the gas sensor with the normal gas concentration at the predetermined position and a judging means for judging the absence or presence of abnormality depending on the combination of the result of the comparison and deliverying a signal if the state is abnormal. As a result, a slight amount of gas responsible to odors released upon abnormality of the plant can be detected by a plurality of gas sensors for different kinds gases to rapidly and easily find abnormal portions in the plant. (I.S.)

  7. Nuclear power plant siting

    International Nuclear Information System (INIS)

    Sulkiewicz, M.; Navratil, J.

    The construction of a nuclear power plant is conditioned on territorial requirements and is accompanied by the disturbance of the environment, land occupation, population migration, the emission of radioactive wastes, thermal pollution, etc. On the other hand, a nuclear power plant makes possible the introduction of district heating and increases the economic and civilization activity of the population. Due to the construction of a nuclear power plant the set limits of negative impacts must not be exceeded. The locality should be selected such as to reduce the unfavourable effects of the plant and to fully use its benefits. The decision on the siting of the nuclear power plant is preceded by the processing of a number of surveys and a wide range of documentation to which the given criteria are strictly applied. (B.H.)

  8. Manganese deficiency in plants

    DEFF Research Database (Denmark)

    Schmidt, Sidsel Birkelund; Jensen, Poul Erik; Husted, Søren

    2016-01-01

    Manganese (Mn) is an essential plant micronutrient with an indispensable function as a catalyst in the oxygen-evolving complex (OEC) of photosystem II (PSII). Even so, Mn deficiency frequently occurs without visual leaf symptoms, thereby masking the distribution and dimension of the problem...... restricting crop productivity in many places of the world. Hence, timely alleviation of latent Mn deficiency is a challenge in promoting plant growth and quality. We describe here the key mechanisms of Mn deficiency in plants by focusing on the impact of Mn on PSII stability and functionality. We also address...... the mechanisms underlying the differential tolerance towards Mn deficiency observed among plant genotypes, which enable Mn-efficient plants to grow on marginal land with poor Mn availability....

  9. Communal biomass conversion plants

    International Nuclear Information System (INIS)

    Holm-Nielsen, J.B.; Huntingford, S.; Halberg, N.

    1993-03-01

    The aim was to show the agricultural advantages of farmers being in connection with Communal Biogas Plant. Whether a more environmentally protectire distribution of plant nutrients from animal manure takes place through a biogas plants distribution system, whether the nitrogen in the digested slurry is better utilized and whether the connection results in slurry transportation-time reduction, are discussed. The average amount of nitrogen from animal manure used per hectare was reduced. The area of manure distribution was larger. The nitrogen efficiency was increased when using digested slurry and purchase of N mineral fertilizer decreased, resulting in considerable reduction in nitrogen leaching. The amount of slurry delivered to the local storage tanks was approximately 45 per cent of the total amount treated on the biogas plant. Conditions of manure transport improved greatly as this was now the responsibility of the communal biomass conversion plant administrators. (AB) (24 refs.)

  10. Encapsulation plant at Forsmark

    International Nuclear Information System (INIS)

    Nystroem, Anders

    2007-08-01

    SKB has already carried out a preliminary study of an encapsulation plant detached from Clab (Central interim storage for spent fuels). This stand-alone encapsulation plant was named FRINK and its assumed siting was the above-ground portion of the final repository, irrespective of the repository's location. The report previously presented was produced in cooperation with BNFL Engineering Ltd in Manchester and the fuel reception technical solution was examined by Gesellschaft fuer Nuklear-Service mbH (GNS) in Hannover and by Societe Generale pour les Techniques Nouvelles (SGN) in Paris. This report is an update of the earlier preliminary study report and is based on the assumption that the encapsulation plant and also the final repository will be sited in the Forsmark area. SKB's main alternative for siting the encapsulation plant is next to Clab. Planning of this facility is ongoing and technical solutions from the planning work have been incorporated in this report. An encapsulation plant placed in proximity to any final repository in Forsmark forms part of the alternative presentation in the application for permission to construct and operate an installation at Clab. The main technical difference between the planned encapsulation plant at Clab and an encapsulation plant at a final repository at Forsmark is how the fuel is managed and prepared before actual encapsulation. Fuel reception at the encapsulation plant in Forsmark would be dry, i.e. there would be no water-filled pools at the facility. Clab is used for verificatory fuel measurements, sorting and drying of the fuel before transport to Forsmark. This means that Clab will require a measure of rebuilding and supplementary equipment. In purely technical terms, the prospects for building an encapsulation plant sited at Forsmark are good. A description of the advantages and drawbacks of siting the encapsulation plant at Clab as opposed to any final repository at Forsmark is presented in a separate report

  11. Encapsulation plant at Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Nystroem, Anders

    2007-08-15

    SKB has already carried out a preliminary study of an encapsulation plant detached from Clab (Central interim storage for spent fuels). This stand-alone encapsulation plant was named FRINK and its assumed siting was the above-ground portion of the final repository, irrespective of the repository's location. The report previously presented was produced in cooperation with BNFL Engineering Ltd in Manchester and the fuel reception technical solution was examined by Gesellschaft fuer Nuklear-Service mbH (GNS) in Hannover and by Societe Generale pour les Techniques Nouvelles (SGN) in Paris. This report is an update of the earlier preliminary study report and is based on the assumption that the encapsulation plant and also the final repository will be sited in the Forsmark area. SKB's main alternative for siting the encapsulation plant is next to Clab. Planning of this facility is ongoing and technical solutions from the planning work have been incorporated in this report. An encapsulation plant placed in proximity to any final repository in Forsmark forms part of the alternative presentation in the application for permission to construct and operate an installation at Clab. The main technical difference between the planned encapsulation plant at Clab and an encapsulation plant at a final repository at Forsmark is how the fuel is managed and prepared before actual encapsulation. Fuel reception at the encapsulation plant in Forsmark would be dry, i.e. there would be no water-filled pools at the facility. Clab is used for verificatory fuel measurements, sorting and drying of the fuel before transport to Forsmark. This means that Clab will require a measure of rebuilding and supplementary equipment. In purely technical terms, the prospects for building an encapsulation plant sited at Forsmark are good. A description of the advantages and drawbacks of siting the encapsulation plant at Clab as opposed to any final repository at Forsmark is presented in a separate

  12. Biofuelled heating plants

    International Nuclear Information System (INIS)

    Gulliksson, Hans; Wennerstaal, L.; Zethraeus, B.; Johansson, Bert-Aake

    2001-11-01

    The purpose of this report is to serve as a basis to enable establishment and operation of small and medium-sized bio-fuel plants, district heating plants and local district heating plants. Furthermore, the purpose of this report is to serve as a guideline and basis when realizing projects, from the first concept to established plant. Taking into account all the phases, from selection of heating system, fuel type, selection of technical solutions, authorization request or application to operate a plant, planning, construction and buying, inspection, performance test, take-over and control system of the plant. Another purpose of the report is to make sure that best available technology is used and to contribute to continuous development of the technology. The report deals mainly with bio-fuelled plants in the effect range 0.3 to10 MW. The term 'plant' refers to combined power and heating plants as well as 'simpler' district heating plants. The last-mentioned is also often referred to as 'local heating plant'. In this context, the term bio fuel refers to a wide range of fuel types. The term bio fuel includes processed fractions like powders, pellets, and briquettes along with unprocessed fractions, such as by-products from the forest industry; chips and bark. Bio fuels also include straw, energy crops and cereal waste products, but these have not been expressly studied in this report. The report is structured with appendixes regarding the various phases of the projects, with the purpose of serving as a helping handbook, or manual for new establishment, helping out with technical and administrative advice and environmental requirements. Plants of this size are already expanding considerably, and the need for guiding principles for design/technology and environmental requirements is great. These guiding principles should comply with the environmental legislation requirements, and must contain advice and recommendations for bio fuel plants in this effect range, also in

  13. Populations in clonal plants

    Directory of Open Access Journals (Sweden)

    Jussi Tammisola

    1986-12-01

    Full Text Available Population phenomena in higher plants are reviewed critically, particularly in relation to clonality. An array of concepts used in the field are discussed. In contrast to animals, higher plants are modular in structure. Plant populations show hierarchy at two levels: ramets and genets. In addition, their demography is far more complicated, since even the direction of development of a ramet may change by rejuvenation. Therefore, formulae concerning animal populations often require modification for plants. Furthermore, at the zygotic stage, higher plants are generally less mobile than animals. Accordingly, their population processes tend to be more local. Most populations of plants have a genetic structure: alleles and genotypes are spatially aggregated. Due to the short-ranged foraging behaviour of pollinators, genetically non-random pollination prevails. A generalized formula for parent-offspring dispersal variance is derived. It is used to analyze the effect of clonality on genetic patchiness in populations. In self-compatible species, an increase in clonality will tend to increase the degree of patchiness, while in self-incompatible species a decrease may result. Examples of population structure studies in different species are presented. A considerable degree of genetic variation appears to be found also in the populations of species with a strong allocation of resources to clonal growth or apomictic seed production. Some consequences of clonality are considered from the point of view of genetic conservation and plant breeding.

  14. Experimental mutagenesis in plants

    International Nuclear Information System (INIS)

    Conger, B.V.

    1979-01-01

    Considerable progress has been made in directed or controlled mutagenesis with bacterial systems, the genetic resolving power of which is much greater than that of higher plants. The mutagen specificity in higher plants has been of great interest, and numerous results and observations have been reported. The advances in the culture of plant cells and tissues have created much interest concerning the possibility of inducing and recovering mutants at the cellular level. There are great problems including the failure to regenerate plants from cells in all but a few species. The genetic and cytogenetic instability in the culture of plant tissues is well known, and the most common nuclear change is polyploidy including aneuploidy. The degree of polyploidy increases with calluses or culture age. In rice, the frequency of aneuploidy is greater in the calluses derived from roots than those derived from stem internodes. Polyploid and/or self-incompatible plant species are not as amenable to conventional mutation breeding techniques as diploid, self-fertilizing species. Inducing mutations in somatic tissues creates the problem of chimeras. However, the new cultivars of highly heterozygous, outcrossing, self-incompatible species are produced by combining several different clones. The performance of the progeny of at least 4 generations removed from the polycross of the parent clones is the important factor, and a high amount of heterozygocity is tolerated within cultivars and even on the same plants. (Yamashita, S.)

  15. Plant state display device

    International Nuclear Information System (INIS)

    Kadota, Kazuo; Ito, Toshiichiro.

    1994-01-01

    The device of the present invention conducts information processing suitable for a man to solve a problem in a plant such as a nuclear power plant incorporating a great amount of information, where safety is required and provides information to an operator. Namely, theories and rules with respect to the flow and balanced state of materials and energy upon plant start-up, and a vapor cycle of operation fluids are symbolized and displayed on the display screen of the device. Then, the display of the plant information suitable to the information processing for a man to dissolve problems is provided. Accordingly, a mechanism for analyzing a purpose of the plant is made more definite, thereby enabling to prevent an erroneous judgement of an operator and occurrence of plant troubles. In addition, a simular effect can also be expected when the theories and rules with respect to the flow and the balanced state of materials and energy and thermohydrodynamic behavior of the operation fluids in a state of after-heat removing operation during shutdown of the plant are symbolized and displayed. (I.S.)

  16. Physiology of woody plants

    CERN Document Server

    Hazewinkel, Michiel; Pallardy, Stephen G

    1996-01-01

    This completely revised classic volume is an up-to-date synthesis of the intensive research devoted to woody plants. Intended primarily as a text for students and a reference for researchers, this interdisciplinary book should be useful to a broad range of scientists from agroforesters, agronomists, and arborists to plant pathologists, ecophysiologists, and soil scientists. Anyone interested in plant physiology will find this text invaluable. Key Features * Includes supplementary chapter summaries and lists of general references * Provides a solid foundation of reference information * Thoroughly updated classic text/reference.

  17. Interelement correlations in plants

    International Nuclear Information System (INIS)

    Markert, B.

    1987-01-01

    The concentration of 25 elements in 4 plant species (Citrus aurantia, Brassica oleracea, Lycopersicon esculentum and Pinus strobus) were linearly correlated. For some element pairs (Ce-Fe, Ce-Ni, Ce-Sb, Ce-Sc, Ce-Zn, Fe-Sb, Fe-Sc, Fe-U, Fe-Zn, K-Cd, La-U, Ni-Sb, Sc-U and Sc-Zn) a high positive correlation coefficient (r = +1) was found. The element pairs Ca-Mg, Hg-U, Ni-Sr and Sr-Zn show a significant negative correlation (r = -1). Plants seem to process some constant interelement relations, independent of plant species. (orig.)

  18. Radiation hormesis in plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae Sung; Song, Hi Sup; Lee, Young Keun; Lee, Byung Hun; Shin, In Chul; Lim, Young Taek

    2000-04-01

    This research was performed to investigate the effects of low dose {gamma}-ray radiation on the seed germination and the following physiological responses in vegetable crops. Special attention was focused on whether the resistance of vegetables against the unfavorable conditions of environment such as subsequent high doses of radiation or Phytophthora blight of pepper could be enhanced as an aspect of radiation hormesis. Analysis and characterization of antioxidant enzyme from plant culture cells and radiation tolerant of transformed plants from antioxidant (POD) were accomplished in the plant irradiated with different dose of {gamma}-ray. (author)

  19. Selenium accumulation by plants.

    Science.gov (United States)

    White, Philip J

    2016-02-01

    Selenium (Se) is an essential mineral element for animals and humans, which they acquire largely from plants. The Se concentration in edible plants is determined by the Se phytoavailability in soils. Selenium is not an essential element for plants, but excessive Se can be toxic. Thus, soil Se phytoavailability determines the ecology of plants. Most plants cannot grow on seleniferous soils. Most plants that grow on seleniferous soils accumulate plant species have evolved tolerance to Se, and commonly accumulate tissue Se concentrations >100 mg Se kg(-1) dry matter. These plants are considered to be Se accumulators. Some species can even accumulate Se concentrations of 1000-15 000 mg Se kg(-1 )dry matter and are called Se hyperaccumulators. This article provides an overview of Se uptake, translocation and metabolism in plants and highlights the possible genetic basis of differences in these between and within plant species. The review focuses initially on adaptations allowing plants to tolerate large Se concentrations in their tissues and the evolutionary origin of species that hyperaccumulate Se. It then describes the variation in tissue Se concentrations between and within angiosperm species and identifies genes encoding enzymes limiting the rates of incorporation of Se into organic compounds and chromosomal loci that might enable the development of crops with greater Se concentrations in their edible portions. Finally, it discusses transgenic approaches enabling plants to tolerate greater Se concentrations in the rhizosphere and in their tissues. The trait of Se hyperaccumulation has evolved several times in separate angiosperm clades. The ability to tolerate large tissue Se concentrations is primarily related to the ability to divert Se away from the accumulation of selenocysteine and selenomethionine, which might be incorporated into non-functional proteins, through the synthesis of less toxic Se metabilites. There is potential to breed or select crops

  20. Radiation hormesis in plant

    International Nuclear Information System (INIS)

    Kim, Jae Sung; Song, Hi Sup; Lee, Young Keun; Lee, Byung Hun; Shin, In Chul; Lim, Young Taek

    2000-04-01

    This research was performed to investigate the effects of low dose γ-ray radiation on the seed germination and the following physiological responses in vegetable crops. Special attention was focused on whether the resistance of vegetables against the unfavorable conditions of environment such as subsequent high doses of radiation or Phytophthora blight of pepper could be enhanced as an aspect of radiation hormesis. Analysis and characterization of antioxidant enzyme from plant culture cells and radiation tolerant of transformed plants from antioxidant (POD) were accomplished in the plant irradiated with different dose of γ-ray. (author)

  1. Nuclear power plants maintenance

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    Nuclear power plants maintenance now appears as an important factor contributing to the competitivity of nuclea energy. The articles published in this issue describe the way maintenance has been organized in France and how it led to an actual industrial activity developing and providing products and services. An information note about Georges Besse uranium enrichment plant (Eurodif) recalls that maintenance has become a main data not only for power plants but for all nuclear industry installations. (The second part of this dossier will be published in the next issue: vol. 1 January-February 1989) [fr

  2. Optofluidics of plants

    Directory of Open Access Journals (Sweden)

    Demetri Psaltis

    2016-05-01

    Full Text Available Optofluidics is a tool for synthesizing optical systems, making use of the interaction of light with fluids. In this paper we explore optofluidic mechanisms that have evolved in plants where sunlight and fluidic control combine to define most of the functionality of the plan. We hope that the presentation of how plants function, from an optofluidics point of view, will open a window for the optics community to the vast literature of plant physiology and provide inspiration for new ideas for the design of bio-mimetic optofluidic devices.

  3. Competitive breeder power plants

    International Nuclear Information System (INIS)

    Winkleblack, R.K.

    1984-01-01

    To utilize the fissile material that is accumulating in the utilities' spent fuel pools, breeder plants must be less expensive than current LWR costs (or utilities will not buy nuclear plants in the near future) and also be highly reliable. The fundamental differences between LWRs and LMFBRs are discussed and recommendations are made for making the most of these differences to design a superior breeder plant that can sell in the future, opening the way to U.S. utilities becoming self-sufficient for fuel supply for centuries

  4. Radiation hormesis in plant

    International Nuclear Information System (INIS)

    Kim, Jae Sung; Song, Hi Sup; Lee, Young Keun; Cun, Ki Jung; Shin, In Chul; Lim, Young Taek

    1999-04-01

    This research was performed to investigate the effects of low dose γ-ray radiation on the seed germination and the following physiological responses in vegetable crops. Special attention was focused on whether the resistance of vegetables against the unfavorable conditions of environment such as acid rain or soil types could be enhanced as an aspect of radiation hormesis. Analysis and characterization of antioxidant enzyme from plant culture cells and radiation tolerant of transformed plants from antioxidant enzyme (POD) were accomplished in the plant irradiated with difference dosage of γ-ray

  5. Coal gasification plant

    Energy Technology Data Exchange (ETDEWEB)

    1977-09-29

    The proposal concerns a stage in the process of cooling the synthetic gas produced in a coal gasification plant at temperatures above 900/sup 0/C. The purpose is to keep the convection heating surface of the subsequent waste heat plant free of dirt. According to the invention, the waste heat plant has a radiation area connected before it, on the heating surfaces of which the slack carried over solidifies. This radiation area has a hydraulic and thermal cleaning system, which can be raised or lowered in a water bath. The subclaims concern all the constructional characteristics of this cleaning system, which causes the solidified slack to crack.

  6. TOR signalling in plants.

    Science.gov (United States)

    Rexin, Daniel; Meyer, Christian; Robaglia, Christophe; Veit, Bruce

    2015-08-15

    Although the eukaryotic TOR (target of rapamycin) kinase signalling pathway has emerged as a key player for integrating nutrient-, energy- and stress-related cues with growth and metabolic outputs, relatively little is known of how this ancient regulatory mechanism has been adapted in higher plants. Drawing comparisons with the substantial knowledge base around TOR kinase signalling in fungal and animal systems, functional aspects of this pathway in plants are reviewed. Both conserved and divergent elements are discussed in relation to unique aspects associated with an autotrophic mode of nutrition and adaptive strategies for multicellular development exhibited by plants. © 2015 Authors; published by Portland Press Limited.

  7. Radiation hormesis in plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae Sung; Song, Hi Sup; Lee, Young Keun; Cun, Ki Jung; Shin, In Chul; Lim, Young Taek

    1999-04-01

    This research was performed to investigate the effects of low dose {gamma}-ray radiation on the seed germination and the following physiological responses in vegetable crops. Special attention was focused on whether the resistance of vegetables against the unfavorable conditions of environment such as acid rain or soil types could be enhanced as an aspect of radiation hormesis. Analysis and characterization of antioxidant enzyme from plant culture cells and radiation tolerant of transformed plants from antioxidant enzyme (POD) were accomplished in the plant irradiated with difference dosage of {gamma}-ray.

  8. Nuclear power plant outages

    International Nuclear Information System (INIS)

    1998-01-01

    The Finnish Radiation and Nuclear Safety Authority (STUK) controls nuclear power plant safety in Finland. In addition to controlling the design, construction and operation of nuclear power plants, STUK also controls refuelling and repair outages at the plants. According to section 9 of the Nuclear Energy Act (990/87), it shall be the licence-holder's obligation to ensure the safety of the use of nuclear energy. Requirements applicable to the licence-holder as regards the assurance of outage safety are presented in this guide. STUK's regulatory control activities pertaining to outages are also described

  9. FRIB Cryogenic Plant Status

    Energy Technology Data Exchange (ETDEWEB)

    Dixon, Kelly D. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Ganni, Venkatarao [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Knudsen, Peter N. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Casagranda, Fabio [Michigan State Univ., East Lansing, MI (United States)

    2015-12-01

    After practical changes were approved to the initial conceptual design of the cryogenic system for MSU FRIB and an agreement was made with JLab in 2012 to lead the design effort of the cryogenic plant, many activities are in place leading toward a cool-down of the linacs prior to 2018. This is mostly due to using similar equipment used at CHLII for the 12 GeV upgrade at JLab and an aggressive schedule maintained by the MSU Conventional Facilities department. Reported here is an updated status of the cryogenic plant, including the equipment procurement status, plant layout, facility equipment and project schedule.

  10. Plant-soil feedbacks: role of plant functional group and plant traits

    NARCIS (Netherlands)

    Cortois, R.; Schröder-Georgi, T.; Weigelt, A.; van der Putten, W.H.; De Deyn, G.B.

    2016-01-01

    Plant-soil feedback (PSF), plant trait and functional group concepts advanced our understanding of plant community dynamics, but how they are interlinked is poorly known. To test how plant functional groups (FGs: graminoids, small herbs, tall herbs, legumes) and plant traits relate to PSF, we grew

  11. Plant Growth Promoting Rhizobacteria

    Indian Academy of Sciences (India)

    IAS Admin

    known to improve plant growth in many ways when compared to ... roles in agricultural productivity. ... Sustainable agriculture: Sustainable agriculture involves the successful management of agricultural re- ... For the first time Kloepper et al.

  12. KWU Nuclear Plant Analyzer

    International Nuclear Information System (INIS)

    Bennewitz, F.; Hummel, R.; Oelmann, K.

    1986-01-01

    The KWU Nuclear Plant Analyzer is a real time engineering simulator based on the KWU computer programs used in plant transient analysis and licensing. The primary goal is to promote the understanding of the technical and physical processes of a nuclear power plant at an on-site training facility. Thus the KWU Nuclear Plant Analyzer is available with comparable low costs right at the time when technical questions or training needs arise. This has been achieved by (1) application of the transient code NLOOP; (2) unrestricted operator interaction including all simulator functions; (3) using the mainframe computer Control Data Cyber 176 in the KWU computing center; (4) four color graphic displays controlled by a dedicated graphic computer, no control room equipment; and (5) coupling of computers by telecommunication via telephone

  13. Nuclear Power Plants (Rev.)

    Energy Technology Data Exchange (ETDEWEB)

    Lyerly, Ray L.; Mitchell III, Walter [Southern Nuclear Engineering, Inc.

    1973-01-01

    Projected energy requirements for the future suggest that we must employ atomic energy to generate electric power or face depletion of our fossil-fuel resources—coal, oil, and gas. In short, both conservation and economic considerations will require us to use nuclear energy to generate the electricity that supports our civilization. Until we reach the time when nuclear power plants are as common as fossil-fueled or hydroelectric plants, many people will wonder how the nuclear plants work, how much they cost, where they are located, and what kinds of reactors they use. The purpose of this booklet is to answer these questions. In doing so, it will consider only central station plants, which are those that provide electric power for established utility systems.

  14. Ferrous Metal Processing Plants

    Data.gov (United States)

    Department of Homeland Security — This map layer includes ferrous metal processing plants in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  15. Nonferrous Metal Processing Plants

    Data.gov (United States)

    Department of Homeland Security — This map layer includes nonferrous metal processing plants in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  16. Plutonium Finishing Plant

    Data.gov (United States)

    Federal Laboratory Consortium — The Plutonium Finishing Plant, also known as PFP, represented the end of the line (the final procedure) associated with plutonium production at Hanford.PFP was also...

  17. Plant Vascular Biology 2010

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Biao

    2014-11-17

    This grant supported the Second International Conference on Plant Vascular Biology (PVB 2010) held July 24-28, 2010 on the campus of Ohio State University, Columbus, Ohio. Biao Ding (Ohio State University; OSU) and David Hannapel (Iowa State University; ISU) served as co-chairs of this conference. Biao Ding served as the local organizer. PVB is defined broadly here to include studies on the biogenesis, structure and function of transport systems in plants, under conditions of normal plant growth and development as well as of plant interactions with pathogens. The transport systems cover broadly the xylem, phloem, plasmodesmata and vascular cell membranes. The PVB concept has emerged in recent years to emphasize the integrative nature of the transport systems and approaches to investigate them.

  18. Bituminization plant Jaslovske Bohunice

    International Nuclear Information System (INIS)

    1999-01-01

    In this leaflet the principle of the bituminization plant for radioactive concentrate (the intermediate liquid radioactive waste generated during the NPP A1, V-1, V-2 operations) solidification used in the Bohunice Radwaste Treatment Centre (BSC RAO) is presented

  19. Plant stem cell niches.

    Science.gov (United States)

    Aichinger, Ernst; Kornet, Noortje; Friedrich, Thomas; Laux, Thomas

    2012-01-01

    Multicellular organisms possess pluripotent stem cells to form new organs, replenish the daily loss of cells, or regenerate organs after injury. Stem cells are maintained in specific environments, the stem cell niches, that provide signals to block differentiation. In plants, stem cell niches are situated in the shoot, root, and vascular meristems-self-perpetuating units of organ formation. Plants' lifelong activity-which, as in the case of trees, can extend over more than a thousand years-requires that a robust regulatory network keep the balance between pluripotent stem cells and differentiating descendants. In this review, we focus on current models in plant stem cell research elaborated during the past two decades, mainly in the model plant Arabidopsis thaliana. We address the roles of mobile signals on transcriptional modules involved in balancing cell fates. In addition, we discuss shared features of and differences between the distinct stem cell niches of Arabidopsis.

  20. Biogas plants; Biogasanlagen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Within the KRdL expert meeting at 30th October, 2012 in Bonn (Federal Republic of Germany), the following lectures were held: (1) New requirements on biomass conversion plants based on the Federal Nuisance Control Ordinance (Hans-Peter Ewens); (2) State of the art of the operation of biomass conversion plants (Christina Dornack); (3) Implementation of the regulation VDI 3475 sheet 4 (Markus Helm); (4) Handling of constraints of residents in the licensing procedure as well as during operation (Helmar Hentschke); (5) Explosion protection for biomass conversion plants considering the matters of immission control (Michael Faber); (6) Microbiological and epidemic-hygienic aspects of agricultural biomass conversion plants and their fermentation residues (Werner Philipp); (7) Emissions of climatic relevant gases at the biogas production (Jacqueline Daniel-Gromke); (8) State of the art in the biogas processing (Joachim Krassowski).

  1. Nuclear power plant construction

    International Nuclear Information System (INIS)

    Lima Moreira, Y.M. de.

    1979-01-01

    The legal aspects of nuclear power plant construction in Brazil, derived from governamental political guidelines, are presented. Their evolution, as a consequence of tecnology development is related. (A.L.S.L.) [pt

  2. Nuclear power plant decommissioning

    International Nuclear Information System (INIS)

    Yaziz Yunus

    1986-01-01

    A number of issues have to be taken into account before the introduction of any nuclear power plant in any country. These issues include reactor safety (site and operational), waste disposal and, lastly, the decommissioning of the reactor inself. Because of the radioactive nature of the components, nuclear power plants require a different approach to decommission compared to other plants. Until recently, issues on reactor safety and waste disposal were the main topics discussed. As for reactor decommissioning, the debates have been academic until now. Although reactors have operated for 25 years, decommissioning of retired reactors has simply not been fully planned. But the Shippingport Atomic Power Plant in Pennysylvania, the first large scale power reactor to be retired, is now being decommissioned. The work has rekindled the debate in the light of reality. Outside the United States, decommissioning is also being confronted on a new plane. (author)

  3. Advanced stellarator power plants

    International Nuclear Information System (INIS)

    Miller, R.L.

    1994-01-01

    The stellarator is a class of helical/toroidal magnetic fusion devices. Recent international progress in stellarator power plant conceptual design is reviewed and comparisons in the areas of physics, engineering, and economics are made with recent tokamak design studies

  4. Protoplasts and plant viruses

    International Nuclear Information System (INIS)

    Murakishi, H.; Lesney, M.S.; Carlson, P.

    1984-01-01

    The use of protoplasts in the study of plant viruses has attracted considerable attention since its inception in the late 1960s. This article is an attempt to assess the current status of protoplasts (primarily) and all cell cultures (in some instances) in studies of virus infection, virus replication, cytopathology, cross-protection, virus resistance, and the use of in vitro methods and genetic engineering to recover virus-resistant plants. These areas of study proved difficult to do entirely with whole plants or plant parts. However, because protoplasts could be synchronously infected with virus, they provided a valuable alternative means of following biochemical and cytological events in relation to the virus growth cycle in a more precise manner than previously possible

  5. Fertilization in Flowering Plants

    Indian Academy of Sciences (India)

    Ecology and the. Environment ... agents (pollinators), the next step before fertilization is to se- .... the embryo sac are referred to as pollen-pistil interaction and play ..... evolutionary success of flowering plants when compared to other groups of ...

  6. Competition between herbage plants

    NARCIS (Netherlands)

    Wit, de C.T.; Bergh, van den J.P.

    1965-01-01

    Starting from work with annuals a model of competition between herbage plants is discussed. It is shown that their mutual interference can only be described adequately if they are grown in mixture and also in monoculture

  7. Photomorphogenesis in plants

    National Research Council Canada - National Science Library

    Kendrick, Richard E; Kronenberg, G. H. M

    1994-01-01

    ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. ... VII VIII XXXI Part 1 Introduction 1. Introduction by Lars Olof Bjorn 1.1 1.2 1.3 1.4 1.5 1.6 A developing research field ... Plant vision...

  8. Reprocessing plants safety

    International Nuclear Information System (INIS)

    Davies, A.G.; Leighton, C.; Millington, D.

    1989-01-01

    The reprocessing of irradiated nuclear fuel at British Nuclear Fuels (BNFL) Sellafield site consists of a number of relatively self-contained activities carried out in separate plants across the site. The physical conditions and time scales applied in reprocessing and storage make it relatively benign. The potential for minor releases of radioactivity under fault conditioning is minimised by plant design definition of control procedures, training and supervision. The risks to both the general public and workforce are shown to be low with all the safety criteria being met. Normal operating conditions also have the potential for some occupational radiation exposure and the plant and workers are monitored continuously. Exposure levels have been reduced steadily and will continue to fall with plant improvements. (U.K.)

  9. International power plant business

    Energy Technology Data Exchange (ETDEWEB)

    Grohe, R.

    1986-03-03

    At the Brown Boveri press seminar 'Energy' in Baden-Baden Rainer Grohe, member of the Brown Boveri board, Mannheim, gave a survey of the activities on the international power plant market in recent years. He showed the vacuities which must be taken into account in this sector today. The drastic escalation of demands on power plant suppliers has lead not to a reduction of protagonists but to an increase. (orig.).

  10. Wind power plant

    Energy Technology Data Exchange (ETDEWEB)

    Caneghem, A.E. von

    1975-07-24

    The invention applies to a wind power plant in which the wind is used to drive windmills. The plant consists basically of a vertical tube with a lateral wind entrance opening with windmill on its lower end. On its upper end, the tube carries a nozzle-like top which increases the wind entering the tube by pressure decrease. The wind is thus made suitable for higher outputs. The invention is illustrated by constructional examples.

  11. Janata biogas plant

    Energy Technology Data Exchange (ETDEWEB)

    Bahadur, S; Singh, K K

    1980-03-01

    The Janata biogas plant is based on the use of local materials and locally available skills only. It is a proven technology at low cost and easy maintenance which should facilitate its extension at a much faster pace especially among the low income groups. This technology is important at this time because of the current crisis in the availability of firewood and mineral fuels. This handbook explains in non-technical language the basic features, design, and construction of this biogas plant. (DC)

  12. The plant mitochondrial proteome

    DEFF Research Database (Denmark)

    Millar, A.H.; Heazlewood, J.L.; Kristensen, B.K.

    2005-01-01

    The plant mitochondrial proteome might contain as many as 2000-3000 different gene products, each of which might undergo post-translational modification. Recent studies using analytical methods, such as one-, two- and three-dimensional gel electrophoresis and one- and two-dimensional liquid...... context to be defined for them. There are indications that some of these proteins add novel activities to mitochondrial protein complexes in plants....

  13. NMR, water and plants

    International Nuclear Information System (INIS)

    As, H. van.

    1982-01-01

    This thesis describes the application of a non-destructive pulsed proton NMR method mainly to measure water transport in the xylem vessels of plant stems and in some model systems. The results are equally well applicable to liquid flow in other biological objects than plants, e.g. flow of blood and other body fluids in human and animals. The method is based on a pulse sequence of equidistant π pulses in combination with a linear magnetic field gradient. (Auth.)

  14. Plant Formate Dehydrogenase

    Energy Technology Data Exchange (ETDEWEB)

    John Markwell

    2005-01-10

    The research in this study identified formate dehydrogenase, an enzyme that plays a metabolic role on the periphery of one-carbon metabolism, has an unusual localization in Arabidopsis thaliana and that the enzyme has an unusual kinetic plasticity. These properties make it possible that this enzyme could be engineered to attempt to engineer plants with an improved photosynthetic efficiency. We have produced transgenic Arabidopsis and tobacco plants with increased expression of the formate dehydrogenase enzyme to initiate further studies.

  15. Detergent zeolite filtration plant

    OpenAIRE

    Stanković Mirjana S.; Pezo Lato L.

    2003-01-01

    The IGPC Engineering Department designed basic projects for detergent zeolite filtration plant, using technology developed in the IGPC laboratories. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects, a production plant with a capacity of 75,000 t/y was manufactured, at "Zeolite Mira", Mira (VE), Italy, in 1997, for increasing detergent zeolite production, from 50,000 to 100,000 t/y. The main goal was to increase the detergent zeoli...

  16. Plant extracts as radioprotectors

    Energy Technology Data Exchange (ETDEWEB)

    Baydoun, S; Al-Oudat, M [Atomic Energy Commission, Department of Radiation Protection and Nuclear Safety, Damascus (Syrian Arab Republic); Al-Achkar, W [Atomic Energy Commission, Department of Radiobiology and Health, Damascus (Syrian Arab Republic)

    1996-09-01

    Several studies show that the extracts of some plants, namely containing vitamins or sulfide components, have radioprotection properties against the effects of ionizing radiation. In Syria, many of hates plants are available. This experiment was conducted in order to test the ability of ten different plants to protect against the radiation damages. These plants are Daucus carota L., Brassica oleracea L, Aloe vera L., Opuntia ficus-indica, Allium cepa L., Capsicum annuum L., Scilla maritima L., Allium sativum L., Rubus sanctus L. and Rosa canina L.Their effects on the protection of E. Coli growth after the exposure to L.D 50 of gamma radiation (100 Gy) were investigated . Two concentrations to each plant extract were tested, both were than 1%. Our results are indicating that the protection depend on plant. The radioprotection factors were ranged between 1.42 to 2.39. The best results were obtained by using the extract of Allium sativum L. (2.01), Opuntia ficus-indica (2.14) and Capsiucum annuum L. (2.39). (author) 16 refs., 2 tabs., 4 figs.

  17. Medicinal plants of Lorestan

    Directory of Open Access Journals (Sweden)

    shahla ahmadi

    2010-03-01

    Full Text Available Collection and determination of medicinal plants in Lorestan province have been carried out for 6 years in the agriculture and natural resources research of center of Lorestan. The aims of this study were collection and identification the medicinal plans that grow in Loretta province, their distribution, habitat, traditional uses, utilized organ, manner of usage, botany specification, local name, Persian name and scientific name. Material and methods: Medicinal plants were collected from different regions by using field and library study for these goals we prepared a list of recorded medicinal plants from Lorestan, identified the local herbal experts. Results: Finally we collected 151 medicinal plant identified that related to 63 families and 90 genuses. The Lamiaceae, Compositae, Legominosae , Liliaceae, Umbelliferae and . Rosaceae are the greatest family in the Lorestan province. Diction: According to the literature 96 medicinal plans were recorded from Lorestan, but during this study we collected and identified 151 medicinal plants in Lorestan province. Comparing with those that recorded from Bushehr 70 sp.(9, Hormozgan 113 sp.(10, Markazi 144 sp. And Kordestan 144 sp(11. We have more diversity but comparing with Zanjan 163 sp.(13, Hamedan 315 sp.(14 And Qazvin 250 sp.(15 We have less diversity in medicinal plants.

  18. Plant extracts as radioprotectors

    International Nuclear Information System (INIS)

    Baydoun, S.; Al-Oudat, M.; Al-Achkar, W.

    1996-09-01

    Several studies show that the extracts of some plants, namely containing vitamins or sulfide components, have radioprotection properties against the effects of ionizing radiation. In Syria, many of hates plants are available. This experiment was conducted in order to test the ability of ten different plants to protect against the radiation damages. These plants are Daucus carota L., Brassica oleracea L, Aloe vera L., Opuntia ficus-indica, Allium cepa L., Capsicum annuum L., Scilla maritima L., Allium sativum L., Rubus sanctus L. and Rosa canina L.Their effects on the protection of E. Coli growth after the exposure to L.D 50 of gamma radiation (100 Gy) were investigated . Two concentrations to each plant extract were tested, both were than 1%. Our results are indicating that the protection depend on plant. The radioprotection factors were ranged between 1.42 to 2.39. The best results were obtained by using the extract of Allium sativum L. (2.01), Opuntia ficus-indica (2.14) and Capsiucum annuum L. (2.39). (author) 16 refs., 2 tabs., 4 figs

  19. Plant extracts as radioprotectors

    International Nuclear Information System (INIS)

    Baydoun, S.; Al-Oudat, M.; Al-Achkar, W.

    1997-01-01

    Several studies show that the extracts of some plants, namely containing vitamins or sulfide components, have radioprotection properties against the effects of ionizing radiation. In Syria, many of hates plants are available. This experiment was conducted in order to test the ability of ten different plants to protect against the radiation damages. These plants are Daucus carota L., Brassica oleracea L, Aloe vera L., Opuntia ficus-indica, Allium cepa L., Capsicum annuum L., Scilla maritima L., Allium sativum L., Rubus sanctus L. and Rosa canina L.Their effects on the protection of E. Coli growth after the exposure to L.D 50 of gamma radiation (100 Gy) were investigated . Two concentrations to each plant extract were tested, both were than 1%. Our results are indicating that the protection depend on plant. The radioprotection factors were ranged between 1.42 to 2.39. The best results were obtained by using the extract of Allium sativum L. (2.01), Opuntia ficus-indica (2.14) and Capsiucum annuum L. (2.39). (author)

  20. Power plants 2010. Lectures

    International Nuclear Information System (INIS)

    2010-01-01

    The proceedings include the following lectures: Facing the challenges - new structures for electricity production. Renewable energies in Europe - chances and challenges. Nuclear outlook in the UK. Sustainable energy for Europe. Requirements of the market and the grid operator at the electricity production companies. Perspectives for the future energy production. Pumped storage plants - status and perspectives. Nuclear power/renewable energies -partners or opponents? New fossil fired power stations in Europe - status and perspectives. Nuclear energy: outlook for new build and lifetime extension in Europe. Biomass in the future European energy market - experiences for dong energy. Meeting the EU 20:20 renewable energy targets: the offshore challenges. DESERTEC: sustainable electricity for Europe, Middle East and North Africa. New power plants in Europe - a challenge for project and quality management. Consideration of safely in new build activities of power plants. Challenges to an integrated development in Maasvlakte, Netherlands. Power enhancement in EnBW power plants. Operational experiences of CCS pilot plants worldwide. Two years of operational experiences with Vattenfall's oxyfuel pilot plant. Pre-conditions for CCS. Storage technologies for a volatile generation. Overview: new generation of gas turbines.

  1. Plant monitoring device

    International Nuclear Information System (INIS)

    Ito, Toru.

    1994-01-01

    The device of the present invention comprises a data collecting section for periodically collecting processed data sent from plant equipments, a top node induction and processing section for an important plant function model for inducing the plant function to be noted particularly by an operator from important plant function models by using process data and a window screen selection section for selecting a window screen to be displayed based on the result of the evaluation for each of function nodes based on the processing described above and determining the layout and automatically forming the display screen. It is constituted so that the kind and the layout of the window under display are checked if they are the same as those one cycle before or not and, if they are different, the screen is automatically switched to a new screen display. Then, operator's psychological burdens such as selection of information and judgement for the operation upon occurrence of plant abnormality and accident can be mitigated, to provide a safe operation circumstance having reinforced monitoring of the function of the whole plant can be provided. (N.H.)

  2. Uranium speciation in plants

    International Nuclear Information System (INIS)

    Guenther, A.; Bernhard, G.; Geipel, G.; Reich, T.; Rossberg, A.; Nitsche, H.

    2003-01-01

    Detailed knowledge of the nature of uranium complexes formed after the uptake by plants is an essential prerequisite to describe the migration behavior of uranium in the environment. This study focuses on the determination of uranium speciation after uptake of uranium by lupine plants. For the first time, time-resolved laser-induced fluorescence spectroscopy and X-ray absorption spectroscopy were used to determine the chemical speciation of uranium in plants. Differences were detected between the uranium speciation in the initial solution (hydroponic solution and pore water of soil) and inside the lupine plants. The oxidation state of uranium did not change and remained hexavalent after it was taken up by the lupine plants. The chemical speciation of uranium was identical in the roots, shoot axis, and leaves and was independent of the uranium speciation in the uptake solution. The results indicate that the uranium is predominantly bound as uranyl(VI) phosphate to the phosphoryl groups. Dandelions and lamb's lettuce showed uranium speciation identical to lupine plants. (orig.)

  3. Plant critical concept

    International Nuclear Information System (INIS)

    O'Regan, P.J.

    1996-01-01

    The objective of the effort summarized in this paper is to support O and M cost reduction efforts by focusing resources on components and processes critical to plant performance. This effort will identify where resources on nonplant critical components and processes can be reduced or eliminated. This method will use a functional assessment as the basis for component-specific evaluations and ranking. This effort consists of two stages conducted in series. The first stage is to deterministically identify that set of plant components that are relevant from a plant performance perspective (i.e., safety, economics, reliability). The second stage probabilistically ranks that set of plant components from an importance perspective, where importance pertains to the particular application and is probabilistically weighted. The results of a pilot study identified that only a relatively small set of components are truly critical from an integrated plant performance perspective. These results are consistent with work being conducted at other nuclear power plants, as well as other commercial facilities. Initial implementation of this effort is estimated to reduce O and M costs on the order of $1 million per year. Subsequent applications are anticipated to increase that savings to $4--$5 million per year

  4. Landscaping plant epigenetics.

    Science.gov (United States)

    McKeown, Peter C; Spillane, Charles

    2014-01-01

    The understanding of epigenetic mechanisms is necessary for assessing the potential impacts of epigenetics on plant growth, development and reproduction, and ultimately for the response of these factors to evolutionary pressures and crop breeding programs. This volume highlights the latest in laboratory and bioinformatic techniques used for the investigation of epigenetic phenomena in plants. Such techniques now allow genome-wide analyses of epigenetic regulation and help to advance our understanding of how epigenetic regulatory mechanisms affect cellular and genome function. To set the scene, we begin with a short background of how the field of epigenetics has evolved, with a particular focus on plant epigenetics. We consider what has historically been understood by the term "epigenetics" before turning to the advances in biochemistry, molecular biology, and genetics which have led to current-day definitions of the term. Following this, we pay attention to key discoveries in the field of epigenetics that have emerged from the study of unusual and enigmatic phenomena in plants. Many of these phenomena have involved cases of non-Mendelian inheritance and have often been dismissed as mere curiosities prior to the elucidation of their molecular mechanisms. In the penultimate section, consideration is given to how advances in molecular techniques are opening the doors to a more comprehensive understanding of epigenetic phenomena in plants. We conclude by assessing some opportunities, challenges, and techniques for epigenetic research in both model and non-model plants, in particular for advancing understanding of the regulation of genome function by epigenetic mechanisms.

  5. Plant monitoring device

    International Nuclear Information System (INIS)

    Moriyama, Kunio.

    1991-01-01

    The monitoring device of the present invention is most suitable to early detection for equipment abnormality, or monitoring of state upon transient conditions such as startup and shutdown of an electric power plant, a large-scaled thermonuclear device and an accelerator plant. That is, in existent moitoring devices, acquired data are stored and the present operation states are monitored in comparison. A plant operation aquisition data reproduction section is disposed to the device. From the past operation conditions stored in the plant operation data aquisition reproducing section, the number of operation cycles that agrees with the present plant operation conditions is sought, to determine the agreed aquired data. Since these aquired data are time sequential data measured based on the standard time determined by the operation sequence, aquired data can be reproduced successively on every sample pitches. With such a constitution, aquired data under the same operation conditions as the present conditions are displayed together with the measured data. Accordingly, accurate monitoring can be conducted from the start-up to the shutdown of the plant. (I.S.)

  6. Molecular plant volatile communication.

    Science.gov (United States)

    Holopainen, Jarmo K; Blande, James D

    2012-01-01

    Plants produce a wide array of volatile organic compounds (VOCs) which have multiple functions as internal plant hormones (e.g., ethylene, methyl jasmonate and methyl salicylate), in communication with conspecific and heterospecific plants and in communication with organisms of second (herbivores and pollinators) and third (enemies of herbivores) trophic levels. Species specific VOCs normally repel polyphagous herbivores and those specialised on other plant species, but may attract specialist herbivores and their natural enemies, which use VOCs as host location cues. Attraction of predators and parasitoids by VOCs is considered an evolved indirect defence, whereby plants are able to indirectly reduce biotic stress caused by damaging herbivores. In this chapter we review these interactions where VOCs are known to play a crucial role. We then discuss the importance of volatile communication in self and nonself detection. VOCs are suggested to appear in soil ecosystems where distinction of own roots from neighbours roots is essential to optimise root growth, but limited evidence of above-ground plant self-recognition is available.

  7. Conservation law of plants' energy value dependence of plants ...

    African Journals Online (AJOL)

    The plants differences in biochemical composition are analyzed, and the conservation law of energy value in plants is obtained. The link between the need for the nutrients and the plants biochemical composition is examined, Liebig's law is specified. Keywords: plant's biochemical composition, biochemistry, energy value in ...

  8. Chapter 15. Plant pathology and managing wildland plant disease systems

    Science.gov (United States)

    David L. Nelson

    2004-01-01

    Obtaining specific, reliable knowledge on plant diseases is essential in wildland shrub resource management. However, plant disease is one of the most neglected areas of wildland resources experimental research. This section is a discussion of plant pathology and how to use it in managing plant disease systems.

  9. Chemical signaling between plants and plant-pathogenic bacteria.

    Science.gov (United States)

    Venturi, Vittorio; Fuqua, Clay

    2013-01-01

    Studies of chemical signaling between plants and bacteria in the past have been largely confined to two models: the rhizobial-legume symbiotic association and pathogenesis between agrobacteria and their host plants. Recent studies are beginning to provide evidence that many plant-associated bacteria undergo chemical signaling with the plant host via low-molecular-weight compounds. Plant-produced compounds interact with bacterial regulatory proteins that then affect gene expression. Similarly, bacterial quorum-sensing signals result in a range of functional responses in plants. This review attempts to highlight current knowledge in chemical signaling that takes place between pathogenic bacteria and plants. This chemical communication between plant and bacteria, also referred to as interkingdom signaling, will likely become a major research field in the future, as it allows the design of specific strategies to create plants that are resistant to plant pathogens.

  10. Plants in alpine environments

    Science.gov (United States)

    Germino, Matthew J.

    2014-01-01

    Alpine and subalpine plant species are of special interest in ecology and ecophysiology because they represent life at the climate limit and changes in their relative abundances can be a bellwether for climate-change impacts. Perennial life forms dominate alpine plant communities, and their form and function reflect various avoidance, tolerance, or resistance strategies to interactions of cold temperature, radiation, wind, and desiccation stresses that prevail in the short growing seasons common (but not ubiquitous) in alpine areas. Plant microclimate is typically uncoupled from the harsh climate of the alpine, often leading to substantially warmer plant temperatures than air temperatures recorded by weather stations. Low atmospheric pressure is the most pervasive, fundamental, and unifying factor for alpine environments, but the resulting decrease in partial pressure of CO2 does not significantly limit carbon gain by alpine plants. Factors such as tree islands and topographic features create strong heterogeneous mosaics of microclimate and snow cover that are reflected in plant community composition. Factors affecting tree establishment and growth and formation of treeline are key to understanding alpine ecology. Carbohydrate and other carbon storage, rapid development in a short growing season, and physiological function at low temperature are prevailing attributes of alpine plants. A major contemporary research theme asks whether chilling at alpine-treeline affects the ability of trees to assimilate the growth resources and particularly carbon needed for growth or whether the growth itself is limited by the alpine environment. Alpine areas tend to be among the best conserved, globally, yet they are increasingly showing response to a range of anthropogenic impacts, such as atmospheric deposition.

  11. Advanced plant design recommendations from Cook Nuclear Plant experience

    International Nuclear Information System (INIS)

    Zimmerman, W.L.

    1993-01-01

    A project in the American Electric Power Service Corporation to review operating and maintenance experience at Cook Nuclear Plant to identify recommendations for advanced nuclear plant design is described. Recommendations so gathered in the areas of plant fluid systems, instrument and control, testing and surveillance provisions, plant layout of equipment, provisions to enhance effective maintenance, ventilation systems, radiological protection, and construction, are presented accordingly. An example for a design review checklist for effective plant operations and maintenance is suggested

  12. Japanese national reference reprocessing plant

    International Nuclear Information System (INIS)

    1978-08-01

    This paper gives a general description of the proposed Japanese national reprocessing plant and of the design philosophy. The plant is in most respects similar to the base case reprocessing plant, with an annual throughput of 100-1500 tU. The plant would be co-located with a fuel fabrication facility

  13. African names for American plants

    NARCIS (Netherlands)

    Andel, van T.R.

    2015-01-01

    African slaves brought plant knowledge to the New World, sometimes applying it to related plants they found there and sometimes bringing Old World plants with them. By tracing the linguistic parallels between names for plants in African languages and in communities descended from African slaves,

  14. Cadmium uptake by plants

    Energy Technology Data Exchange (ETDEWEB)

    Haghiri, F.

    1973-01-01

    Absorption of /sup 115m/Cd by soybean (Gylcine max l.) plants via foliar and root systems and translocation into the seed was determined. The uptake of /sup 115m/Cd by soybeans via the root system was more efficient than that of the foliar placement. Growth and Cd concentrations of soybean and wheat (Triticum aestivum l.) tops were influenced by soil-applied Cd. In both crops, the Cd concentration of plant tops increased while yield decreased with increasing levels of applied Cd. Cadmium toxicitiy began to occur in both crops at the lowest level of soil applied Cd (2.5 ppM). With soybean plants, Cd toxicity symptoms resembled fe chlorosis. For wheat plants there were no visual symptoms other than the studied growth. The relative concentration of Cd found in several vegetable crops varied depending on the plant species. The relative Cd concentration in descending order for various vegetables was lettuce (Lactuca sativa l.) > radish top (Raphanus sativus l.) > celery stalk (Apium graveolens l.) > celery leaves greater than or equal to green pepper (Capsicum frutescens l.) > radish roots.

  15. Plant critical concept

    International Nuclear Information System (INIS)

    O'Regan, P.J.

    1995-01-01

    The achievement of operation and maintenance (O ampersand M) cost reductions is a prime concern for plant operators. Initiatives by the nuclear industry to address this concern are under way and/or in development. These efforts include plant reliability studies, reliability-centered maintenance, risk ranking and testing philosophies, performance-based testing philosophies, graded quality assurance, and so forth. This paper presents the results of an effort to develop a methodology that integrates and applies the common data and analysis requirements for a number of risk-based and performance-based initiatives. This initial phase of the effort applied the methodology and its results to two initiatives. These were the procurement function and the preventive maintenance function. This effort integrated multiple programs and functions to identify those components that are truly critical from an integrated plant performance perspective. The paper describes the scope of the effort, the development of a methodology to identify plant critical components, and the application of these results to the maintenance rule compliance, preventive maintenance, and procurement functions at the candidate plant

  16. Benchmarking Nuclear Power Plants

    International Nuclear Information System (INIS)

    Jakic, I.

    2016-01-01

    One of the main tasks an owner have is to keep its business competitive on the market while delivering its product. Being owner of nuclear power plant bear the same (or even more complex and stern) responsibility due to safety risks and costs. In the past, nuclear power plant managements could (partly) ignore profit or it was simply expected and to some degree assured through the various regulatory processes governing electricity rate design. It is obvious now that, with the deregulation, utility privatization and competitive electricity market, key measure of success used at nuclear power plants must include traditional metrics of successful business (return on investment, earnings and revenue generation) as well as those of plant performance, safety and reliability. In order to analyze business performance of (specific) nuclear power plant, benchmarking, as one of the well-established concept and usual method was used. Domain was conservatively designed, with well-adjusted framework, but results have still limited application due to many differences, gaps and uncertainties. (author).

  17. Ornamental Plant Breeding

    Directory of Open Access Journals (Sweden)

    Flávia Barbosa Silva Botelho

    2015-04-01

    Full Text Available World’s ornamental plant market, including domestic market of several countries and its exports, is currently evaluated in 107 billion dollars yearly. Such estimate highlights the importance of the sector in the economy of the countries, as well as its important social role, as it represents one of the main activities, which contributes to income and employment. Therefore a well-structured plant breeding program, which is connected with consumers’ demands, is required in order to fulfill these market needs globally. Activities related to pre-breeding, conventional breeding, and breeding by biotechnological techniques constitute the basis for the successful development of new ornamental plant cultivars. Techniques that involve tissue culture, protoplast fusion and genetic engineering greatly aid conventional breeding (germplasm introduction, plant selection and hybridization, aiming the obtention of superior genotypes. Therefore it makes evident, in the literature, the successful employment of genetic breeding, since it aims to develop plants with commercial value that are also competitive with the ones available in the market.

  18. Plant arginyltransferases (ATEs

    Directory of Open Access Journals (Sweden)

    Tatiana Domitrovic

    Full Text Available Abstract Regulation of protein stability and/or degradation of misfolded and damaged proteins are essential cellular processes. A part of this regulation is mediated by the so-called N-end rule proteolytic pathway, which, in concert with the ubiquitin proteasome system (UPS, drives protein degradation depending on the N-terminal amino acid sequence. One important enzyme involved in this process is arginyl-t-RNA transferase, known as ATE. This enzyme acts post-translationally by introducing an arginine residue at the N-terminus of specific protein targets to signal degradation via the UPS. However, the function of ATEs has only recently begun to be revealed. Nonetheless, the few studies to date investigating ATE activity in plants points to the great importance of the ATE/N-end rule pathway in regulating plant signaling. Plant development, seed germination, leaf morphology and responses to gas signaling in plants are among the processes affected by the ATE/N-end rule pathway. In this review, we present some of the known biological functions of plant ATE proteins, highlighting the need for more in-depth studies on this intriguing pathway.

  19. Soft valves in plants

    Science.gov (United States)

    Park, Keunhwan; Tixier, Aude; Christensen, Anneline; Arnbjerg-Nielsen, Sif; Zwieniecki, Maciej; Jensen, Kaare

    2017-11-01

    Water and minerals flow from plant roots to leaves in the xylem, an interconnected network of vascular conduits that spans the full length of the organism. When a plant is subjected to drought stress, air pockets can spread inside the xylem, threatening the survival of the plant. Many plants prevent propagation of air by using hydrophobic nano-membranes in the ``pit'' pores that link adjacent xylem cells. This adds considerable resistance to flow. Interestingly, torus-margo pit pores in conifers are open and offer less resistance. To prevent propagation of air, conifers use a soft gating mechanism, which relies on hydrodynamic interactions between the xylem liquid and the elastic pit. However, it is unknown exactly how it is able to combine the seemingly antagonist functions of high permeability and resistance to propagation of air. We conduct experiments on biomimetic pores to elucidate the flow regulation mechanism. The design of plant valves is compared to other natural systems and optimal strategies are discussed. This work was supported by a research Grant (13166) from VILLUM FONDEN.

  20. AECL's plant Information Technologies

    International Nuclear Information System (INIS)

    DeVerno, M.; Lupton, L.; Didsbury, R.; Judd, R.

    1998-01-01

    The competitiveness of the world-wide energy market is a continual driving force for improvements to CANDU performance and lower operating, maintenance, and administration costs. As in other industries, advanced Information Technologies (IT) are changing the way we work and conduct business. The nuclear industry is no different and there exists strong incentives to improve work processes and provide faster and more flexible access to the information needed to effectively manage and maintain nuclear plant assets. AECL has responded to these forces through the development of a vision of integrated IT systems addressing all phases of nuclear plant development and operations. This includes the initial engineering, design, and construction processes as well as support to the long-term operations and maintenance. Integral to the AECL vision is the need for cost-effective engineering and operational configuration management systems, proactive maintenance processes and systems, and advanced plant surveillance and diagnostics. This paper presents the vision and describes the integrated information systems needed to manage both the design basis and operating plant data systems to ensure the cost-effective, long-term viability of CANDU plants. (author)

  1. Antidiabetic Plants of Iran

    Directory of Open Access Journals (Sweden)

    Ashrafeddin Goushegir

    2011-10-01

    Full Text Available To identify the antidiabetic plants of Iran, a systematic review of the published literature on the efficacy of Iranian medicinal plant for glucose control in patients with type 2 diabetes mellitus was conducted. We performed an electronic literature search of MEDLINE, Science Direct, Scopus, Proquest, Ebsco, Googlescholar, SID, Cochrane Library Database, from 1966 up to June 2010. The search terms were complementary and alternative medicine (CAM, diabetes mellitus, plant (herb, Iran, patient, glycemic control, clinical trial, RCT, natural or herbal medicine, hypoglycemic plants, and individual herb names from popular sources, or combination of these key words. Available Randomized Controlled Trials (RCT published in English or Persian language examined effects of an herb (limited to Iran on glycemic indexes in type 2 diabetic patients were included. Among all of the articles identified in the initial database search, 23 trials were RCT, examining herbs as potential therapy for type 2 diabetes mellitus. The key outcome for antidiabetic effect was changes in blood glucose or HbA1 c, as well as improves in insulin sensitivity or resistance. Available data suggest that several antidiabetic plants of Iran need further study. Among the RCT studies, the best evidence in glycemic control was found in Citrullus colocynthus, Ipomoea betatas, Silybum marianum and Trigonella foenum graecum.

  2. Geothermal Power Generation Plant

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, Tonya [Oregon Inst. of Technology, Klamath Falls, OR (United States). Geo-Heat Center

    2013-12-01

    Oregon Institute of Technology (OIT) drilled a deep geothermal well on campus (to 5,300 feet deep) which produced 196°F resource as part of the 2008 OIT Congressionally Directed Project. OIT will construct a geothermal power plant (estimated at 1.75 MWe gross output). The plant would provide 50 to 75 percent of the electricity demand on campus. Technical support for construction and operations will be provided by OIT’s Geo-Heat Center. The power plant will be housed adjacent to the existing heat exchange building on the south east corner of campus near the existing geothermal production wells used for heating campus. Cooling water will be supplied from the nearby cold water wells to a cooling tower or air cooling may be used, depending upon the type of plant selected. Using the flow obtained from the deep well, not only can energy be generated from the power plant, but the “waste” water will also be used to supplement space heating on campus. A pipeline will be construction from the well to the heat exchanger building, and then a discharge line will be construction around the east and north side of campus for anticipated use of the “waste” water by facilities in an adjacent sustainable energy park. An injection well will need to be drilled to handle the flow, as the campus existing injection wells are limited in capacity.

  3. Pinellas Plant facts

    International Nuclear Information System (INIS)

    1986-09-01

    This plant was built in 1956 in response to a need for the manufacture of neutron generators, a principal component in nuclear weapons. The neutron generators consist of a miniaturized linear ion accelerator assembled with the pulsed electrical power supplies required for its operation. The ion accelerator, or neutron tube, requires ultra clean, high vacuum technology: hermetic seals between glass, ceramic, glass-ceramic, and metal materials: plus high voltage generation and measurement technology. The existence of these capabilities at the Pinellas Plant has led directly to the assignment of the lightning arrester connector, specialty capacitor, vacuum switch, and crystal resonator. Active and reserve batteries and the radioisotopically-powered thermoelectric generator draw on the materials measurement and controls technologies which are required to ensure neutron generator life. A product development and production capability in alumina ceramics, cermet (electrical) feedthroughs, and glass ceramics has become a specialty of the plant; the laboratories monitor the materials and processes used by the plant's commercial suppliers of ferroelectric ceramics. In addition to the manufacturing facility, a production development capability is maintained at the Pinellas Plant

  4. Latina nuclear power plant

    International Nuclear Information System (INIS)

    1976-03-01

    In the period under review, the Latina power plant produced 1009,07 million kWh with a utilization factor of 72% and an availability factor of 80,51%. The disparity between the utilization and availability factors was mainly due to the shutdown of the plant owing to trade union strife. The reasons for non-availability (19,49%) were almost all related to the functioning of the conventional part and the general servicing of the plant (18 September-28 October). During the shutdown for maintenance, an inspection of the steel members and parts of the core stabilizing structure was made in order to check for the familiar oxidation phenomena caused by CO 2 ; the results of the inspection were all satisfactory. Operation of the plant during 1974 was marked by numerous power cutbacks as a result of outages of the steam-raising units (leaks from the manifolds) and main turbines (inspection and repairs to the LP rotors). Since it was first brought into commercial operation, the plant has produced 13,4 thousand million kWh

  5. Plants cultivation in controlled containments

    International Nuclear Information System (INIS)

    2000-01-01

    The plants cultivation in controlled containments permits to the - Departement d'Ecophysiologie Vegetale et de Microbiologie (DVEM) - of the CEA to lead several topics of research. The works of DVEM which are based on the molecular labelling, technique adapted to plants, contribute to understand the plant - soil relationships and the plant growth process. In addition, the staff of DVEM study the impact of pollutant heavy metals, existing in the soil, on plants and the plant stress induced by oxygen, light, ionizing radiations,... and defence mechanisms of plants (F. M.)

  6. Owners of nuclear power plants

    International Nuclear Information System (INIS)

    Wood, R.S.

    1991-07-01

    This report indicates percentage ownership of commercial nuclear power plants by utility companies. The report includes all plants operating, under construction, docketed for NRC safety and environmental reviews, or under NRC antitrust review, but does not include those plants announced but not yet under review or those plants formally cancelled. Part 1 of the report lists plants alphabetically with their associated applicants or licensees and percentage ownership. Part 2 lists applicants or licensees alphabetically with their associated plants and percentage ownership. Part 1 also indicates which plants have received operating licenses (OLS)

  7. PV power plants

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Within the international seminar of the Ostbayerisches Technologie-Transfer-Institut e.V. (OTTI) at 11th June, 2012 in Munich (Federal Republic of Germany), the following lectures were held: (1) Technical due diligence (Dietmar Obst); (2) Certification / rating system for large PV plants (Robert Pfatischer); (3) O and M requirements (Lars Rulf); (4) IR photography for large scale systems (Bernhard Weinreich); (5) New market models for PV systems - direct marketing and sales of PV electricity (Martin Schneider); (6) Needs and benefits for plant certification for grid connection and operation (Christoph Luetke-Lengerich); (7) Lare volume module testing / Screening in the field and workshop (Semir Merzoug); (8) Dismantling costs of large scale PV plants (Siegfried Schimpf).

  8. Plant redox proteomics

    DEFF Research Database (Denmark)

    Navrot, Nicolas; Finnie, Christine; Svensson, Birte

    2011-01-01

    PTMs in regulating enzymatic activities and controlling biological processes in plants. Notably, proteins controlling the cellular redox state, e.g. thioredoxin and glutaredoxin, appear to play dual roles to maintain oxidative stress resistance and regulate signal transduction pathways via redox PTMs......In common with other aerobic organisms, plants are exposed to reactive oxygen species resulting in formation of post-translational modifications related to protein oxidoreduction (redox PTMs) that may inflict oxidative protein damage. Accumulating evidence also underscores the importance of redox....... To get a comprehensive overview of these types of redox-regulated pathways there is therefore an emerging interest to monitor changes in redox PTMs on a proteome scale. Compared to some other PTMs, e.g. protein phosphorylation, redox PTMs have received less attention in plant proteome analysis, possibly...

  9. Collective biogas plants

    International Nuclear Information System (INIS)

    1992-01-01

    Papers contributed to the European seminar on collective biogas plants held at Herning, Denmark on October 22-23 under the auspices of the Commission of the European Communities, Directorate-General for Energy (DG XVII) are presented. Within the framework of the THERMIE programme, a network of OPETs (Organizations for the Promotion of Energy Technologies) was set up in order to disseminate information on new energy technologies throughout the European communities. The potential for further implementation of centralized capacity for the conversion of animal manures and other organic wastes to bio-fuels, not only in central and eastern Europe but also in the developing countries, is discussed in addition to the relevant technologies. Actual biomass conversion plants are described and details are given on operational experience and plant management. Agricultural, economic and policy aspects are also dealt with. (AB)

  10. Town gas plants

    International Nuclear Information System (INIS)

    Anastos, G.J.; Johnson, G.M.; Schapot, R.M.; Velez, V.G.

    1990-01-01

    Town gas plant sites are receiving increasing attention from the utility industry and regulatory communities. This attention has been prompted by greater environmental awareness of impacts due to past disposal practices and the understanding that gas plant wastes contain a wide range of chemical constituents that have persisted in the environment. This paper discusses the history of the town gas plant industry, the various processes utilized and the resultant by-products and wastes. Potential problem areas relating to these sites as well as potential approaches to site characterization are addressed. Included are recommendations for the phasing of site investigations and the use of relatively inexpensive and rapid field screening techniques to identify contamination

  11. Plant stem cell niches.

    Science.gov (United States)

    Stahl, Yvonne; Simon, Rüdiger

    2005-01-01

    Stem cells are required to support the indeterminate growth style of plants. Meristems are a plants stem cell niches that foster stem cell survival and the production of descendants destined for differentiation. In shoot meristems, stem cell fate is decided at the populational level. The size of the stem cell domain at the meristem tip depends on signals that are exchanged with cells of the organizing centre underneath. In root meristems, individual stem cells are controlled by direct interaction with cells of the quiescent centre that lie in the immediate neighbourhood. Analysis of the interactions and signaling processes in the stem cell niches has delivered some insights into the molecules that are involved and revealed that the two major niches for plant stem cells are more similar than anticipated.

  12. Nuclear plant life extension

    International Nuclear Information System (INIS)

    Negin, C.A.

    1989-01-01

    The nuclear power industry's addressing of life extension is a natural trend in the maturation of this technology after 20 years of commercial operation. With increasing emphasis on how plants are operated, and less on how to build them, attention is turning on to maximizing the use of these substantial investments. The first studies of life extension were conducted in the period from 1978 and 1982. These were motivated by the initiation, by the Nuclear Regulatory Commission (NRC), of studies to support decommissioning rulemaking. The basic conclusions of those early studies that life extension is feasible and worth pursuing have not been changed by the much more extensive investigations that have since been conducted. From an engineering perspective, life extension for nuclear plants is fundamentally the same as for fossil plants

  13. Individual plant examination: Submittal guidance

    International Nuclear Information System (INIS)

    1989-08-01

    Based on a Policy Statement on Severe Accidents Regarding Future Designs and Existing Plants, the performance of a plant examination is requested from the licensee of each nuclear power plant. The plant examination looks for vulnerabilities to severe accidents and cost-effective safety improvements that reduce or eliminate the important vulnerabilities. This document delineates guidance for reporting the results of that plant examination. 38 refs., 2 tabs

  14. Urea metabolism in plants.

    Science.gov (United States)

    Witte, Claus-Peter

    2011-03-01

    Urea is a plant metabolite derived either from root uptake or from catabolism of arginine by arginase. In agriculture, urea is intensively used as a nitrogen fertilizer. Urea nitrogen enters the plant either directly, or in the form of ammonium or nitrate after urea degradation by soil microbes. In recent years various molecular players of plant urea metabolism have been investigated: active and passive urea transporters, the nickel metalloenzyme urease catalyzing the hydrolysis of urea, and three urease accessory proteins involved in the complex activation of urease. The degradation of ureides derived from purine breakdown has long been discussed as a possible additional metabolic source for urea, but an enzymatic route for the complete hydrolysis of ureides without a urea intermediate has recently been described for Arabidopsis thaliana. This review focuses on the proteins involved in plant urea metabolism and the metabolic sources of urea but also addresses open questions regarding plant urea metabolism in a physiological and agricultural context. The contribution of plant urea uptake and metabolism to fertilizer urea usage in crop production is still not investigated although globally more than half of all nitrogen fertilizer is applied to crops in the form of urea. Nitrogen use efficiency in crop production is generally well below 50% resulting in economical losses and creating ecological problems like groundwater pollution and emission of nitric oxides that can damage the ozone layer and function as greenhouse gasses. Biotechnological approaches to improve fertilizer urea usage bear the potential to increase crop nitrogen use efficiency. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  15. Ion channels in plants.

    Science.gov (United States)

    Hedrich, Rainer

    2012-10-01

    Since the first recordings of single potassium channel activities in the plasma membrane of guard cells more than 25 years ago, patch-clamp studies discovered a variety of ion channels in all cell types and plant species under inspection. Their properties differed in a cell type- and cell membrane-dependent manner. Guard cells, for which the existence of plant potassium channels was initially documented, advanced to a versatile model system for studying plant ion channel structure, function, and physiology. Interestingly, one of the first identified potassium-channel genes encoding the Shaker-type channel KAT1 was shown to be highly expressed in guard cells. KAT1-type channels from Arabidopsis thaliana and its homologs from other species were found to encode the K(+)-selective inward rectifiers that had already been recorded in early patch-clamp studies with guard cells. Within the genome era, additional Arabidopsis Shaker-type channels appeared. All nine members of the Arabidopsis Shaker family are localized at the plasma membrane, where they either operate as inward rectifiers, outward rectifiers, weak voltage-dependent channels, or electrically silent, but modulatory subunits. The vacuole membrane, in contrast, harbors a set of two-pore K(+) channels. Just very recently, two plant anion channel families of the SLAC/SLAH and ALMT/QUAC type were identified. SLAC1/SLAH3 and QUAC1 are expressed in guard cells and mediate Slow- and Rapid-type anion currents, respectively, that are involved in volume and turgor regulation. Anion channels in guard cells and other plant cells are key targets within often complex signaling networks. Here, the present knowledge is reviewed for the plant ion channel biology. Special emphasis is drawn to the molecular mechanisms of channel regulation, in the context of model systems and in the light of evolution.

  16. Integrated Gasification SOFC Plant with a Steam Plant

    DEFF Research Database (Denmark)

    Rokni, Masoud; Pierobon, Leonardo

    2011-01-01

    A hybrid Solid Oxide Fuel Cell (SOFC) and Steam Turbine (ST) plant is integrated with a gasification plant. Wood chips are fed to the gasification plant to produce biogas and then this gas is fed into the anode side of a SOFC cycle to produce electricity and heat. The gases from the SOFC stacks...... enter into a burner to burn the rest of the fuel. The offgases after the burner are now used to generate steam in a Heat Recovery Steam Generator (HRSG). The generated steam is expanded in a ST to produce additional power. Thus a triple hybrid plant based on a gasification plant, a SOFC plant...... and a steam plant is presented and studied. The plant is called as IGSS (Integrated Gasification SOFC Steam plant). Different systems layouts are presented and investigated. Electrical efficiencies up to 56% are achieved which is considerably higher than the conventional integrated gasification combined...

  17. Plant biotechnology: transgenic crops.

    Science.gov (United States)

    Shewry, Peter R; Jones, Huw D; Halford, Nigel G

    2008-01-01

    Transgenesis is an important adjunct to classical plant breeding, in that it allows the targeted manipulation of specific characters using genes from a range of sources. The current status of crop transformation is reviewed, including methods of gene transfer, the selection of transformed plants and control of transgene expression. The application of genetic modification technology to specific traits is then discussed, including input traits relating to crop production (herbicide tolerance and resistance to insects, pathogens and abiotic stresses) and output traits relating to the composition and quality of the harvested organs. The latter include improving the nutritional quality for consumers as well as the improvement of functional properties for food processing.

  18. Wind power plant

    Energy Technology Data Exchange (ETDEWEB)

    Weiss, G

    1975-11-20

    A wind power plant is proposed suitable for electicity generation or water pumping. This plant is to be self-adjusting to various wind velocities and to be kept in operation even during violent storms. For this purpose the mast, carrying the wind rotor and pivotable around a horizontal axis is tiltable and equipped with a wind blind. Further claims contain various configurations of the tilting base resp. the cut in of an elastic link, the attachment and design of the wind blind as well as the constructive arrangement of one or more dynamos.

  19. Power plant process computer

    International Nuclear Information System (INIS)

    Koch, R.

    1982-01-01

    The concept of instrumentation and control in nuclear power plants incorporates the use of process computers for tasks which are on-line in respect to real-time requirements but not closed-loop in respect to closed-loop control. The general scope of tasks is: - alarm annunciation on CRT's - data logging - data recording for post trip reviews and plant behaviour analysis - nuclear data computation - graphic displays. Process computers are used additionally for dedicated tasks such as the aeroball measuring system, the turbine stress evaluator. Further applications are personal dose supervision and access monitoring. (orig.)

  20. Savannah River Plant environment

    International Nuclear Information System (INIS)

    Dukes, E.K.

    1984-03-01

    On June 20, 1972, the Atomic Energy Commission designated 192,323 acres of land near Aiken, SC, as the nation's first National Environmental Research Park. The designated land surrounds the Department of Energy's Savannah River Plant production complex. The site, which borders the Savannah River for 17 miles, includes swampland, pine forests, abandoned town sites, a large man-made lake for cooling water impoundment, fields, streams, and watersheds. This report is a description of the geological, hydrological, meteorological, and biological characteristics of the Savannah River Plant site and is intended as a source of information for those interested in environmental research at the site. 165 references, 68 figures, 52 tables

  1. Quantitative plant ecology

    DEFF Research Database (Denmark)

    Damgaard, Christian

    2014-01-01

    This e-book is written in the Wolfram' CDF format (download free CDF player from Wolfram.com) The objective of this e-book is to introduce the population ecological concepts for measuring and predicting the ecological success of plant species. This will be done by focusing on the measurement...... and statistical modelling of plant species abundance and the relevant ecological processes that control species abundance. The focus on statistical modelling and likelihood function based methods also means that more algorithm based methods, e.g. ordination techniques and boosted regression tress...

  2. PLANTS, SOURCE FOR BIOFUELS

    Directory of Open Access Journals (Sweden)

    Irina Ramona PECINGINĂ

    2016-12-01

    Full Text Available The most affordable alternative energy sources to fossil plants with hydropower are some oils that accumulate in different organs other accumulating carbohydrates with high energy value. They are known worldwide and cultivated a number of plant species entering the oilseeds, which provides significant production of edible oil (soybean, sunflower, etc. Vegetable oils or their product derived biodiesel fuels are potential diesel engines, representing an alternative to fuels. The most promising suitable for the production of oil crops "with short circuit "or biodiesel are fruits and seeds, both herbaceous and tree.

  3. ITER plant systems

    International Nuclear Information System (INIS)

    Kolbasov, B.; Barnes, C.; Blevins, J.

    1991-01-01

    As part of a series of documents published by the IAEA that summarize the results of the Conceptual Design Activities for the ITER project, this publication describes the conceptual design of the ITER plant systems, in particular (i) the heat transport system, (ii) the electrical distribution system, (iii) the requirements for radioactive equipment handling, the hot cell, and waste management, (iv) the supply system for fluids and operational chemicals, (v) the qualitative analyses of failure scenarios and methods of burn stability control and emergency shutdown control, (vi) analyses of tokamak building functions and design requirements, (vii) a plant layout, and (viii) site requirements. Refs, figs and tabs

  4. Fossil power plant automation

    International Nuclear Information System (INIS)

    Divakaruni, S.M.; Touchton, G.

    1991-01-01

    This paper elaborates on issues facing the utilities industry and seeks to address how new computer-based control and automation technologies resulting from recent microprocessor evolution, can improve fossil plant operations and maintenance. This in turn can assist utilities to emerge stronger from the challenges ahead. Many presentations at the first ISA/EPRI co-sponsored conference are targeted towards improving the use of computer and control systems in the fossil and nuclear power plants and we believe this to be the right forum to share our ideas

  5. Plant engineering network

    International Nuclear Information System (INIS)

    Angus, M.J.; Goossen, J.

    1996-01-01

    The Plant Engineering Network (PEN) is a utility-vendor relationship focussed on reducing O and M costs, while maintaining the safe and reliable operation of partner plants through sharing resources, using telecommunications systems for collaborative engineering, coordinating and streamlining work processes, and sharing financial risk and reward. This paper examines how Pacific Gas and Electric (PG and E) established a PEN organization and realized over =0.5 million U.S. in 1994, the first year of implementation, and approximately =2 million U.S. savings in 1995. (author)

  6. Total Logistic Plant Solutions

    Directory of Open Access Journals (Sweden)

    Dusan Dorcak

    2016-02-01

    Full Text Available The Total Logistics Plant Solutions, plant logistics system - TLPS, based on the philosophy of advanced control processes enables complex coordination of business processes and flows and the management and scheduling of production in the appropriate production plans and planning periods. Main attributes of TLPS is to create a comprehensive, multi-level, enterprise logistics information system, with a certain degree of intelligence, which accepts the latest science and research results in the field of production technology and logistics. Logistic model of company understands as a system of mutually transforming flows of materials, energy, information, finance, which is realized by chain activities and operations

  7. Methylome evolution in plants.

    Science.gov (United States)

    Vidalis, Amaryllis; Živković, Daniel; Wardenaar, René; Roquis, David; Tellier, Aurélien; Johannes, Frank

    2016-12-20

    Despite major progress in dissecting the molecular pathways that control DNA methylation patterns in plants, little is known about the mechanisms that shape plant methylomes over evolutionary time. Drawing on recent intra- and interspecific epigenomic studies, we show that methylome evolution over long timescales is largely a byproduct of genomic changes. By contrast, methylome evolution over short timescales appears to be driven mainly by spontaneous epimutational events. We argue that novel methods based on analyses of the methylation site frequency spectrum (mSFS) of natural populations can provide deeper insights into the evolutionary forces that act at each timescale.

  8. Power plants 2009. Lectures

    International Nuclear Information System (INIS)

    2009-01-01

    Within the Annual Conference 2009 of the VGB PowerTech e.V. (Essen, Federal Republic of Germany) from 23rd to 25th May, 2009, in Lyon (France) the following lectures were held: (1) Electricity demand, consequences of the financial and economic crisis - Current overview 2020 for the EU-27 (Hans ten Berge); (2) Status and perspectives of the electricity generation mix in France (Bernard Dupraz); (3) European electricity grid - status and perspective (Dominique Maillard); (4) Technologies and acceptance in the European energy market (Gordon MacKerran); (5) EPR construction in Finland, China, France, (Claude Jaouen); (6) EPR Flamanville 3: A project on the path towards nuclear revival (Jacques Alary); (7) Worldwide nuclear Revival and acceptance (Luc Geraets); (8) An overview on the status of final disposal of radioactive wastes worldwide (Piet Zuidema); (9) Who needs pumped storage plants? PSP are partner to grid stability and renewable energies (Hans-Christoph Funke); (10) Sustainable use of water resources to generate electricity safely and efficiently (Patrick Tourasse); (11) The growth strategy of RWE Innogy - Role of RES in RWE strategy (Fritz Vahrenholt); (12) Solar technologies towards grid parity - key factors and timeframe (G. Gigliucci); (13) Overview on CCS technologies and results of Vattenfalls oxyfuel pilot plant (Philippe Paelinck); (14) Development perspectives of lignite-based IGCC-plants with CCS (Dietmar Keller); (15) Post combustion capture plants - concept and plant integration (Wolfgang Schreier); (16) CCS fossil power generation in a carbon constraint world (Daniel Hofmann); (17) CEZ group strategy in Central and South Eastern Europe (Jan Zizka); (18) Strategy and projects of DONG Energy (Jens Erik Pedersen); (19) E.ON coal-based power generation of the future - The highly efficient power plant and downstream separation of carbon dioxide (Gerhard Seibel); (20) Final sage of first supercritical 460 MW e l. CFB Boiler construction - firs

  9. Wind power plant

    Energy Technology Data Exchange (ETDEWEB)

    Kling, A

    1977-01-13

    The wind power plant described has at least one rotor which is coupled to an electricity generator. The systems are fixed to a suspended body so that it is possible to set up the wind power plant at greater height where one can expect stronger and more uniform winds. The anchoring on the ground or on a floating body is done by mooring cables which can simultaneously have the function of an electric cable. The whole system can be steered by fins. The rotor system itself consists of at least one pair of contrarotating, momentum balanced rotors.

  10. Conceptualizing Pharmaceutical Plants

    DEFF Research Database (Denmark)

    Larsen, Bent Dalgaard; Jensen, Klaes Ladeby; Gjøl, Mikkel

    2006-01-01

    In the conceptual design phase of pharmaceutical plants as much as 80%-90% of the total cost of a project is committed. It is therefore essential that the chosen concept is viable. In this design process configuration and 3D models can help validate the decisions made. Designing 3D models...... is a complex task and requires skilled users. We demonstrate that a simple 2D/3D configuration tool can support conceptualizing of pharmaceutical plants. Present paper reports on preliminary results from a full scale implementation project at a Danish engineering company....

  11. Ardennes nuclear power plant

    International Nuclear Information System (INIS)

    1974-12-01

    The SENA nuclear power plant continued to operate, as before, at authorized rated power, namely 905MWth during the first half year and 950MWth during the second half year. Net energy production:2028GWh; hours phased to the line: 7534H; availability factor: 84%; utilization factor: 84%; total shutdowns:19; number of scrams:10; cost per KWh: 4,35 French centimes. Overall, the plant is performing very satisfactory. Over the last three years net production has been 5900GWh, corresponding to in average utilization factor of 83%

  12. Nuclear power plant

    International Nuclear Information System (INIS)

    Orlov, V.V.; Rineisky, A.A.

    1975-01-01

    The invention is aimed at designing a nuclear power plant with a heat transfer system which permits an accelerated fuel regeneration maintaining relatively high initial steam values and efficiency of the steam power circuit. In case of a plant with three circuits the secondary cooling circuit includes a steam generator with preheater, evaporator, steam superheater and intermediate steam superheater. At the heat supply side the latter is connected with its inlet to the outlet of the evaporator and with its outlet to the low-temperature side of the secondary circuit

  13. Monitoring wood heating plants

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The overall aim of the project is to support the increased use of biomass heating plant in the UK by improving the quality and quantity of information available to suppliers and users. This aim will be achieved by: providing a qualitative assessment of the operational performance of a representative range of biomass heating installations including summaries of technical information; providing good case studies for a range of installations addressing the varied market demands; collating performance data of existing installations so as to improve the performance and/or reduce capital and operating costs of existing and future installations; and providing basic operator training and recommending methods optimising/improving plant performance. (author)

  14. Apoplastic interactions between plants and plant root intruders

    Directory of Open Access Journals (Sweden)

    Kanako eMitsumasu

    2015-08-01

    Full Text Available Numerous pathogenic or parasitic organisms attack plant roots to obtain nutrients, and the apoplast including the plant cell wall is where the plant cell meets such organisms. Root-parasitic angiosperms and nematodes are two distinct types of plant root parasites but share some common features in their strategies for breaking into plant roots. Striga and Orobanche are obligate root parasitic angiosperms that cause devastating agricultural problems worldwide. Parasitic plants form an invasion organ called a haustorium, where plant cell wall degrading enzymes (PCWDEs are highly expressed. Plant-parasitic nematodes are another type of agriculturally important plant root parasite. These nematodes breach the plant cell walls by protruding a sclerotized stylet from which PCWDEs are secreted. Responding to such parasitic invasion, host plants activate their own defense responses against parasites. Endoparasitic nematodes secrete apoplastic effectors to modulate host immune responses and to facilitate the formation of a feeding site. Apoplastic communication between hosts and parasitic plants also contributes to their interaction. Parasitic plant germination stimulants, strigolactones (SLs, are recently identified apoplastic signals that are transmitted over long distances from biosynthetic sites to functioning sites. Here, we discuss recent advances in understanding the importance of apoplastic signals and cell walls for plant-parasite interactions.

  15. Apoplastic interactions between plants and plant root intruders.

    Science.gov (United States)

    Mitsumasu, Kanako; Seto, Yoshiya; Yoshida, Satoko

    2015-01-01

    Numerous pathogenic or parasitic organisms attack plant roots to obtain nutrients, and the apoplast including the plant cell wall is where the plant cell meets such organisms. Root parasitic angiosperms and nematodes are two distinct types of plant root parasites but share some common features in their strategies for breaking into plant roots. Striga and Orobanche are obligate root parasitic angiosperms that cause devastating agricultural problems worldwide. Parasitic plants form an invasion organ called a haustorium, where plant cell wall degrading enzymes (PCWDEs) are highly expressed. Plant-parasitic nematodes are another type of agriculturally important plant root parasite. These nematodes breach the plant cell walls by protruding a sclerotized stylet from which PCWDEs are secreted. Responding to such parasitic invasion, host plants activate their own defense responses against parasites. Endoparasitic nematodes secrete apoplastic effectors to modulate host immune responses and to facilitate the formation of a feeding site. Apoplastic communication between hosts and parasitic plants also contributes to their interaction. Parasitic plant germination stimulants, strigolactones, are recently identified apoplastic signals that are transmitted over long distances from biosynthetic sites to functioning sites. Here, we discuss recent advances in understanding the importance of apoplastic signals and cell walls for plant-parasite interactions.

  16. B Plant hazards assessment

    International Nuclear Information System (INIS)

    Broz, R.E.

    1994-01-01

    This document establishes the technical basis in support of Emergency Planning Activities for B Plant on the Hanford Site. The document represents an acceptable interpretation of the implementing guidance document for DOE Order 5500.3A. Through this document, the technical basis for the development of facility specific , Emergency Action Levels and the Emergency Planning Zone is demonstrated

  17. Nuclear power plant analyzer

    International Nuclear Information System (INIS)

    Stritar, A.

    1986-01-01

    The development of Nuclear Power Plant Analyzers in USA is described. There are two different types of Analyzers under development in USA, the forst in Idaho and Los Alamos national Lab, the second in brookhaven National lab. That one is described in detail. The computer hardware and the mathematical models of the reactor vessel thermalhydraulics are described. (author)

  18. Plant research '76

    Energy Technology Data Exchange (ETDEWEB)

    1976-01-01

    Overall objective remains unchanged: to contribute to the knowledge, with strong emphasis on fundamental problems, of how plants function, the roles they play in the environment and energy relations of the world, and how these roles may be optimized for the benefit of mankind. (PCS)

  19. Drought Signaling in Plants

    Indian Academy of Sciences (India)

    depending upon the source and nature of signaling: (i) hormone signal, (ii) .... plants to regulate the rate of transpiration through minor structural .... cell has to keep spending energy (in the form of A TP) to maintain a .... enzymes and proteins in the regulation of cellular metabolism can be determined by either inactivating.

  20. Nuclear power plant

    International Nuclear Information System (INIS)

    Wieser, R.

    1979-01-01

    The reactor pressure vessel consists of two parts. A cylindrical lower part with a hemispherical steel roof is placed at some distance within an equally shaped pressure vessel of concrete. Both vessels are standing on a common bottom plate. The interspace is kept at subpressure. It serves to contain ring galleries, elevator shafts, and power plant components. (GL) [de

  1. Recombinant Cytokines from Plants

    Czech Academy of Sciences Publication Activity Database

    Sirko, A.; Vaněk, Tomáš; Gora-Sochacka, A.; Redkiewicz, P.

    2011-01-01

    Roč. 12, č. 6 (2011), s. 3536-3552 ISSN 1661-6596 Institutional research plan: CEZ:AV0Z50380511 Keywords : cytokines * pharmaceutical proteins * plant-based production systems Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 2.598, year: 2011

  2. Phenolics and Plant Allelopathy

    Directory of Open Access Journals (Sweden)

    De-An Jiang

    2010-12-01

    Full Text Available Phenolic compounds arise from the shikimic and acetic acid (polyketide metabolic pathways in plants. They are but one category of the many secondary metabolites implicated in plant allelopathy. Phenolic allelochemicals have been observed in both natural and managed ecosystems, where they cause a number of ecological and economic problems, such as declines in crop yield due to soil sickness, regeneration failure of natural forests, and replanting problems in orchards. Phenolic allelochemical structures and modes of action are diverse and may offer potential lead compounds for the development of future herbicides or pesticides. This article reviews allelopathic effects, analysis methods, and allelopathic mechanisms underlying the activity of plant phenolic compounds. Additionally, the currently debated topic in plant allelopathy of whether catechin and 8-hydroxyquinoline play an important role in Centaurea maculata and Centaurea diffusa invasion success is discussed. Overall, the main purpose of this review is to highlight the allelopacthic potential of phenolic compounds to provide us with methods to solve various ecology problems, especially in regard to the sustainable development of agriculture, forestry, nature resources and environment conservation.

  3. Plant breeding and genetics

    Science.gov (United States)

    The ultimate goal of plant breeding is to develop improved crops. Improvements can be made in crop productivity, crop processing and marketing, and/or consumer quality. The process of developing an improved cultivar begins with intercrossing lines with high performance for the traits of interest, th...

  4. Plant monitor system

    International Nuclear Information System (INIS)

    Scarola, K.; Jamison, D.; Manazir, R.; Rescori, R.; Harmon, D.

    1991-01-01

    An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system which is nuclear qualified for rapid response to changes in plant parameters and a component control system which together provide a discrete monitoring and control capability at a panel in the control room. A separate data processing system, which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs and a large, overhead integrated process status overview board. The discrete indicator and alarm system and the data processing system receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the main machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof. (author)

  5. TAPCHAN Wave Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    1983-10-01

    The Tapered Channel Wave Power Plant (TAPCHAN) is based on a new method for wave energy conversion. The principle of operation can be explained by dividing the system into the following four sub-systems: Firstly, a collector which is designed to concentrate the water energy and optimize collection efficiency for a range of frequencies and directions. Secondly, the energy converter, in which the energy of the collected waves is transformed into potential energy in an on-shore water reservoir. This is the unique part of the power plant. It consists of a gradually narrowing channel with wall heights equal to the filling level of the reservoir (typical heights 3-7 m). The waves enter the wide end of the channel and as they propagate down the narrowing channel, the wave height is amplified until the wavecrests spill over the walls. Thirdly, a reservoir which provides a stable water supply for the turbines. Finally, the hydroelectric power plant, where well established techniques are used for the generation of electric power. The water turbine driving the electric generator is of a low head type, such as a Kaplan or a tubular turbine. It must be designed for salt water operation and should have good regulation capabilities. Power plants based on the principle described, are now offered on a commercial basis.

  6. Plant Modernization Programs

    International Nuclear Information System (INIS)

    O'Hara, John

    2004-01-01

    Most nuclear plants were designed and built from the 1960's through the 1990's. These plants employ predominantly analog instrumentation and control (I and C) technology, and their control rooms are made up of primarily hardwired controls (e.g., switches, knobs and handles) and displays (e.g., gauges, linear scales and indicator lights). Over the past several years, these plants have been modernized with digital I and C and computer-based human-system interfaces (HSIs) such as software-based process controls, touch-screen interfaces and large-screen, overview displays. As these computer based HIS technologies are integrated into control rooms based on conventional technology, hybrid control rooms are created. The paper summarizes lessons learned from the study of plant modernization programs over the past ten years so that they can be used to help improve the modification process. While the research focused on the impact of technology change on human performance, a number of organizational and programmatic issues were observed as well. Eleven lessons learned are presented

  7. Plants under continuous light

    NARCIS (Netherlands)

    Velez Ramirez, A.I.; Ieperen, van W.; Vreugdenhill, D.; Millenaar, F.F.

    2011-01-01

    Continuous light is an essential tool for understanding the plant circadian clock. Additionally, continuous light might increase greenhouse food production. However, using continuous light in research and practice has its challenges. For instance, most of the circadian clock-oriented experiments

  8. Nuclear plant scram reduction

    International Nuclear Information System (INIS)

    Wiegle, H.R.

    1986-01-01

    The Nuclear Utility Management and Human Resources Committee (NUMARC) is a confederation of all 55 utilities with nuclear plants either in operation or under construction. NUMARC was formed in April 1984 by senior nuclear executives with hundreds of man-years of plant experience to improve (plant) performance and resolve NRC concerns. NUMARC has adopted 10 commitments in the areas of management, training, staffing and performance. One of these commitments is to strive to reduce automatic trips to 3 per year per unit for calendar year 1985 for plants in commercial operation greater than 3 years (with greater than 25% capacity factor). This goal applies to any unplanned automatic protection system trips at any time when the reactor is critical. Each utility has committed to develop methods to thoroughly evaluate all unplanned automatic trips to identify the root causes and formulate plans to correct the root causes thus reducing future unplanned scrams. As part of this program, the Institute of Nuclear Power Operations (INPO) collects and evaluates information on automatic reactor trips. It publishes the results of these evaluations to aid the industry to identify root causes and corrective actions

  9. Italian steam power plants

    Energy Technology Data Exchange (ETDEWEB)

    von Rautenkranz, J

    1939-01-01

    A brief history of geothermal power production in Italy is presented. Boric acid has been produced on an industrial scale since 1818. The first electrical power was generated in 1904, and by 1939 the output of geothermal power plants had reached 500 GWh, with major expansion of facilities planned.

  10. Plants and Medicinal Chemistry

    Science.gov (United States)

    Bailey, D.

    1977-01-01

    This is the first of two articles showing how plants that have been used in folk medicine for many centuries are guiding scientists in the design and preparation of new and potent drugs. Opium and its chemical derivatives are examined at length in this article. (Author/MA)

  11. Whitebark pine planting guidelines

    Science.gov (United States)

    Ward McCaughey; Glenda L. Scott; Kay L. Izlar

    2009-01-01

    This article incorporates new information into previous whitebark pine guidelines for planting prescriptions. Earlier 2006 guidelines were developed based on review of general literature, research studies, field observations, and standard US Forest Service survival surveys of high-elevation whitebark pine plantations. A recent study of biotic and abiotic factors...

  12. Power plant at sea

    International Nuclear Information System (INIS)

    Roggen, M.

    2000-01-01

    Drilling platforms are rather inefficient when it comes to their own power supply. In view of ecotax and their environmental image, the offshore industry particularly the Norwegians is highly committed to changing this situation. An efficient power plant, specially designed for the offshore industry, might just prove to be the answer to their prayers

  13. Mechanisms in Plant Development

    Energy Technology Data Exchange (ETDEWEB)

    Hake, Sarah [USDA ARS Plant Gene Expression Center

    2013-08-21

    This meeting has been held every other year for the past twenty-two years and is the only regularly held meeting focused specifically on plant development. Topics covered included: patterning in developing tissues; short and long distance signaling; differentiation of cell types; the role of epigenetics in development; evolution; growth.

  14. Plant Biotech Lab Manual.

    Science.gov (United States)

    Tant, Carl

    This book provides laboratory experiments to enhance any food science/botany curriculum. Chapter 1, "Introduction," presents a survey of the techniques used in plant biotechnology laboratory procedures. Chapter 2, "Micronutrition," discusses media and nutritional requirements for tissue culture studies. Chapter 3, "Sterile Seeds," focuses on the…

  15. Radiosensitivity in plants

    International Nuclear Information System (INIS)

    Nauman, A.F.

    1979-01-01

    The report presents a compilation of available data on the sensitivity of plants to ionizing radiation, and provides basic information on methods of determining such sensitivities, or of estimating radiosensitivities by calcuation of the nuclear factors upon which they depend. The scope of the data presented here is necessarily limited to the most generally useful radiobiological end points and to the most commonly-used types of radiation. Many of the factors which influence radiosensitivity, particularly nuclear factors, will be discussed. Emphasis will be upon whole-plant studies done at Brookhaven National Laboratory by A.H. Sparrow and his associates, since these studies are the source of most of the available radiosensitivity data and of all the sensitivity predictions listed here. Data presented here include summaries of experimentally-determined radiosensitivities at various end points for both herbaceous and woody higher plants, and for a few species of ferns and lower plants. The algae and fungi have not been considered here due to space limitations

  16. Chromosome painting in plants.

    NARCIS (Netherlands)

    Schubert, I.; Fransz, P.F.; Fuchs, J.; Jong, de J.H.

    2001-01-01

    The current 'state-of-art' as to chromosome painting in plants is reviewed. We define different situations described as painting so far: i) Genomic in situ hybridisation (GISH) with total genomic DNA to distinguish alien chromosomes on the basis of divergent dispersed repeats, ii) 'Chromosomal in

  17. Nuclear Power Plant Technician

    Science.gov (United States)

    Randall, George A.

    1975-01-01

    The author recognizes a body of basic knowledge in nuclear power plant technoogy that can be taught in school programs, and lists the various courses, aiming to fill the anticipated need for nuclear-trained manpower--persons holding an associate degree in engineering technology. (Author/BP)

  18. Plant cell culture initiation

    NARCIS (Netherlands)

    Hall, R.D.

    2000-01-01

    The use of cultured plant cells in either organized or unorganized form has increased vey considerably in the last 10-15 yr. Many new technologies have been developed and applications in both fundamental and applied research have led to the development of some powerful tools for improving our

  19. Screening for Plant Features

    NARCIS (Netherlands)

    Heijden, van der G.W.A.M.; Polder, G.

    2015-01-01

    In this chapter, an overview of different plant features is given, from (sub)cellular to canopy level. A myriad of methods is available to measure these features using image analysis, and often, multiple methods can be used to measure the same feature. Several criteria are listed for choosing a

  20. The plant exocyst

    NARCIS (Netherlands)

    Zhang, Y.; Emons, A.M.C.; Ketelaar, T.

    2010-01-01

    exocyst is an octameric vesicle tethering complex that functions upstream of SNARE mediated exocytotic vesicle fusion with the plasma membrane. All proteins in the complex have been conserved during evolution, and genes that encode the exocyst subunits are present in the genomes of all plants

  1. Plants flex their skeletons

    DEFF Research Database (Denmark)

    Foster, Randy; Mattsson, Ole; Mundy, John

    2003-01-01

    Recent work on the fragile fiber mutants of Arabidopsis has identified microtubule-associated proteins that affect the orientation of cellulose microfibrils in cell walls, a major determinant of plant elongation growth. These same proteins are implicated in responses to gibberellin, provoking fresh...

  2. Quality maintenance Tropical Plants

    Directory of Open Access Journals (Sweden)

    Gláucia Moraes Dias

    2016-11-01

    Full Text Available The climatic characteristics of the country favor the cultivation of tropical flowers. The continued expansion of this market is due the beauty, exoticit nature and postharvest longevity of flower. However, little is known about the postharvest of tropical plants. Therefore, this paper provides information on harvest, handling and storage of cut tropical plantspostharvest, storage temperature, conditioning solution.

  3. Radiosensitivity in plants

    Energy Technology Data Exchange (ETDEWEB)

    Nauman, A F

    1979-01-01

    The report presents a compilation of available data on the sensitivity of plants to ionizing radiation, and provides basic information on methods of determining such sensitivities, or of estimating radiosensitivities by calcuation of the nuclear factors upon which they depend. The scope of the data presented here is necessarily limited to the most generally useful radiobiological end points and to the most commonly-used types of radiation. Many of the factors which influence radiosensitivity, particularly nuclear factors, will be discussed. Emphasis will be upon whole-plant studies done at Brookhaven National Laboratory by A.H. Sparrow and his associates, since these studies are the source of most of the available radiosensitivity data and of all the sensitivity predictions listed here. Data presented here include summaries of experimentally-determined radiosensitivities at various end points for both herbaceous and woody higher plants, and for a few species of ferns and lower plants. The algae and fungi have not been considered here due to space limitations.

  4. Peru, People and Plants.

    Science.gov (United States)

    Thompson, Dennis

    Designed for horticulture, horticulture therapy, and botany students at Edmonds Community College (Washington), this 6-hour module explores the pre-Columbian use of plant materials in Peru and its relationships to cultural practices in modern Peru. The first sections provide basic information about the module, such as its objectives, the concepts…

  5. Fertilization in Flowering Plants

    Indian Academy of Sciences (India)

    ... for the right pollen,the pistil imposes a tough competition amongst them, comparableto a swayamvara of Indian mythology, to select the bestavailable pollen. Flowering plants have evolved into a matriarchalsociety. The selection of the male partner is totally theprerogative of the mother (pistil); the boy (pollen grain) andthe ...

  6. T Plant hazards assessment

    International Nuclear Information System (INIS)

    Broz, R.E.

    1994-01-01

    This document establishes the technical basis in support of Emergency Planning activities for the T Plant on the Hanford Site. The document represents an acceptable interpretation of the implementing guidance document for DOE ORDER 5500.3A. Through this document, the technical basis for the development of facility specific Emergency Action Levels and the Emergency Planning Zone is demonstrated

  7. Steam power plant

    International Nuclear Information System (INIS)

    Campbell, J.W.E.

    1981-01-01

    This invention relates to power plant forced flow boilers operating with water letdown. The letdown water is arranged to deliver heat to partly expanded steam passing through a steam reheater connected between two stages of the prime mover. (U.K.)

  8. Garigliano nuclear power plant

    International Nuclear Information System (INIS)

    1976-03-01

    During the period under review, the Garigliano power station produced 1,028,77 million kWh with a utilization factor of 73,41% and an availability factor of 85,64%. The disparity between the utilization and availability factors was mainly due to a shutdown of about one and half months owing to lack of staff at the plant. The reasons for nonavailability (14.36%) break down as follows: nuclear reasons 11,49%; conventional reasons 2,81%; other reasons 0,06%. During the period under review, no fuel replacements took place. The plant functioned throughout with a single reactor reticulation pump and resulting maximum available capacity of 150 MWe gross. After the month of August, the plant was operated at levels slightly below the maximum available capacity in order to lengthen the fuel cycle. The total number of outages during the period under review was 11. Since the plant was brought into commercial operation, it has produced 9.226 million kWh

  9. Evolution of plant senescence

    Directory of Open Access Journals (Sweden)

    Young Mike

    2009-07-01

    Full Text Available Abstract Background Senescence is integral to the flowering plant life-cycle. Senescence-like processes occur also in non-angiosperm land plants, algae and photosynthetic prokaryotes. Increasing numbers of genes have been assigned functions in the regulation and execution of angiosperm senescence. At the same time there has been a large expansion in the number and taxonomic spread of plant sequences in the genome databases. The present paper uses these resources to make a study of the evolutionary origins of angiosperm senescence based on a survey of the distribution, across plant and microbial taxa, and expression of senescence-related genes. Results Phylogeny analyses were carried out on protein sequences corresponding to genes with demonstrated functions in angiosperm senescence. They include proteins involved in chlorophyll catabolism and its control, homeoprotein transcription factors, metabolite transporters, enzymes and regulators of carotenoid metabolism and of anthocyanin biosynthesis. Evolutionary timelines for the origins and functions of particular genes were inferred from the taxonomic distribution of sequences homologous to those of angiosperm senescence-related proteins. Turnover of the light energy transduction apparatus is the most ancient element in the senescence syndrome. By contrast, the association of phenylpropanoid metabolism with senescence, and integration of senescence with development and adaptation mediated by transcription factors, are relatively recent innovations of land plants. An extended range of senescence-related genes of Arabidopsis was profiled for coexpression patterns and developmental relationships and revealed a clear carotenoid metabolism grouping, coordinated expression of genes for anthocyanin and flavonoid enzymes and regulators and a cluster pattern of genes for chlorophyll catabolism consistent with functional and evolutionary features of the pathway. Conclusion The expression and phylogenetic

  10. Plant life management optimized utilization of existing nuclear power plants

    International Nuclear Information System (INIS)

    Watzinger, H.; Erve, M.

    1999-01-01

    For safe, reliable and economical nuclear power generation it is of central importance to understand, analyze and manage aging-related phenomena and to apply this information in the systematic utilization and as-necessary extension of the service life of components and systems. An operator's overall approach to aging and plant life management which also improves performance characteristics can help to optimize plant operating economy. In view of the deregulation of the power generation industry with its increased competition, nuclear power plants must today also increasingly provide for or maintain a high level of plant availability and low power generating costs. This is a difficult challenge even for the newest, most modern plants, and as plants age they can only remain competitive if a plant operator adopts a strategic approach which takes into account the various aging-related effects on a plant-wide basis. The significance of aging and plant life management for nuclear power plants becomes apparent when looking at their age: By the year 2000 roughly fifty of the world's 434 commercial nuclear power plants will have been in operation for thirty years or more. According to the International Atomic Energy Agency, as many as 110 plants will have reached the thirty-year service mark by the year 2005. In many countries human society does not push the construction of new nuclear power plants and presumably will not change mind within the next ten years. New construction licenses cannot be expected so that for economical and ecological reasons existing plants have to be operated unchallengeably. On the other hand the deregulation of the power production market is asking just now for analysis of plant life time to operate the plants at a high technical and economical level until new nuclear power plants can be licensed and constructed. (author)

  11. Nuclear power plant safety

    International Nuclear Information System (INIS)

    Otway, H.J.

    1974-01-01

    Action at the international level will assume greater importance as the number of nuclear power plants increases, especially in the more densely populated parts of the world. Predictions of growth made prior to October 1973 [9] indicated that, by 1980, 14% of the electricity would be supplied by nuclear plants and by the year 2000 this figure would be about 50%. This will make the topic of international co-operation and standards of even greater importance. The IAEA has long been active in providing assistance to Member States in the siting design and operation of nuclear reactors. These activities have been pursued through advisory missions, the publication of codes of practice, guide books, technical reports and in arranging meetings to promote information exchange. During the early development of nuclear power, there was no well-established body of experience which would allow formulation of internationally acceptable safety criteria, except in a few special cases. Hence, nuclear power plant safety and reliability matters often received an ad hoc approach which necessarily entailed a lack of consistency in the criteria used and in the levels of safety required. It is clear that the continuation of an ad hoc approach to safety will prove inadequate in the context of a world-wide nuclear power industry, and the international trade which this implies. As in several other fields, the establishment of internationally acceptable safety standards and appropriate guides for use by regulatory bodies, utilities, designers and constructors, is becoming a necessity. The IAEA is presently planning the development of a comprehensive set of basic requirements for nuclear power plant safety, and the associated reliability requirements, which would be internationally acceptable, and could serve as a standard frame of reference for nuclear plant safety and reliability analyses

  12. Photooxidative stress in plants

    International Nuclear Information System (INIS)

    Foyer, C.H.; Lelandais, M.; Kunert, K.J.

    1994-01-01

    The light-dependent generation of active oxygen species is termed photooxidative stress. This can occur in two ways: (1) the donation of energy or electrons directly to oxygen as a result of photosynthetic activity; (2) exposure of tissues to ultraviolet irradiation. The light-dependent destruction of catalase compounds the problem. Although generally detrimental to metabolism, superoxide and hydrogen peroxide may serve useful functions if rigorously controlled and compartmentalised. During photosynthesis the formation of active oxygen species is minimised by a number of complex and refined regulatory mechanisms. When produced, active oxygen species are eliminated rapidly by efficient antioxidative systems. The chloroplast is able to use the production and destruction of hydrogen peroxide to regulate the thermal dissipation of excess excitation energy. This is an intrinsic feature of the regulation of photosynthetic electron transport. Photoinhibition and photooxidation only usually occur when plants are exposed to stress. Active oxygen species are part of the alarm-signalling processes in plants. These serve to modify metabolism and gene expression so that the plant can respond to adverse environmental conditions, invading organisms and ultraviolet irradiation. The capacity of the antioxidative defense system is often increased at such times but if the response is not sufficient, radical production will exceed scavenging and ultimately lead to the disruption of metabolism. Oxidative damage arises in high light principally when the latter is in synergy with additional stress factors such as chilling temperatures or pollution. Environmental stress can modify the photooxidative processes in various ways ranging from direct involvement in light-induced free radical formation to the inhibition of metabolism that renders previously optimal light levels excessive. It is in just such situations that the capacity for the production of active oxygen species can exceed that

  13. Heating plant privatization stagnates

    International Nuclear Information System (INIS)

    Janoska, J.; Benka, M.; Sobinkovic, B.; Haluza, I.

    2005-01-01

    The state has been talking about privatization of 6 municipal heating plants since 2001. The tenders were to start last year. But nothing has happened and the future is uncertain. The city councils would prefer to receive, if not 100%, then at least a majority stake in the heating plants free of charge. But the Cabinet has decided to sell 51% to investors. The privatization agency - the National Property Fund (FNM) is preparing a proposal to increase the stake offered for sale to 67%. According to information provided by the FNM the sale will begin after Cabinet approval. The Fund intends to apply the same model to the sale of all the heating plants. Last year, a major German company Verbundnetz Gas declared its interest in purchasing large municipal heating plants in Slovakia. But it has been waiting for a response ever since. The French company - Dalkia, which has 10-years' experience of doing business in Slovakia, is interested in all the heating plants to be offered for sale. The Austrian company - Stefe is not new to the business either, it is interested mainly in the regions where it has already established itself - Central and Eastern Slovakia. Strategic investors expect financial groups to show interest too. The Penta Group has not hid its ambitions - it has already privatised a company which represents the key to the future development of heat management in Bratislava - Paroplynovy cyklus. Whereas Penta is not new to the heat production business another financial group - Slavia Capital is still surveying the sector. Should it not succeed, it plans several projects that would allow it to take a stake in the sector

  14. Radiochemistry in nuclear power plants

    International Nuclear Information System (INIS)

    Schwarz, W.

    2007-01-01

    Radiochemistry is employed in nuclear power plants not as an end in itself but, among other things, as a main prerequisite of optimum radiation protection. Radiochemical monitoring of various loops provides important information about sources of radioactivity, activity distribution in the plant and its changes. In the light of these analytical findings, plant crews are able to take measures having a positive effect on radiation levels in the plant. The example of a BWR plant is used to show, among other things, how radiochemical analyses helped to reduce radiation levels in a plant and, as a consequence, to decrease clearly radiation exposure of the personnel despite higher workloads. (orig.)

  15. Stainless steels in power plant and plant construction. Papers

    International Nuclear Information System (INIS)

    1994-01-01

    The conference report comprises 14 papers on the corrosion characteristics of stainless steels in power plant and plant engineering. 9 papers are available as separate records in the ENERGY database. (MM) [de

  16. Remediation Using Plants and Plant Enzymes: A Progress Report

    National Research Council Canada - National Science Library

    1995-01-01

    .... In every case, the sources are plants growing near the sediment. The use of plants for remediation of hazardous materials such as TNT or other munitions like RDX and HMX has led to a new approach to remediation-- phytoremediation...

  17. Design of plant safety model in plant enterprise engineering environment

    International Nuclear Information System (INIS)

    Gabbar, Hossam A.; Suzuki, Kazuhiko; Shimada, Yukiyasu

    2001-01-01

    Plant enterprise engineering environment (PEEE) is an approach aiming to manage the plant through its lifecycle. In such environment, safety is considered as the common objective for all activities throughout the plant lifecycle. One approach to achieve plant safety is to embed safety aspects within each function and activity within such environment. One ideal way to enable safety aspects within each automated function is through modeling. This paper proposes a theoretical approach to design plant safety model as integrated with the plant lifecycle model within such environment. Object-oriented modeling approach is used to construct the plant safety model using OO CASE tool on the basis of unified modeling language (UML). Multiple views are defined for plant objects to express static, dynamic, and functional semantics of these objects. Process safety aspects are mapped to each model element and inherited from design to operation stage, as it is naturally embedded within plant's objects. By developing and realizing the plant safety model, safer plant operation can be achieved and plant safety can be assured

  18. Plant responses to plant growth-promoting rhizobacteria

    NARCIS (Netherlands)

    Loon, L.C. van

    2007-01-01

    Non-pathogenic soilborne microorganisms can promote plant growth, as well as suppress diseases. Plant growth promotion is taken to result from improved nutrient acquisition or hormonal stimulation. Disease suppression can occur through microbial antagonism or induction of resistance in the plant.

  19. Plant air systems safety study: Portsmouth Gaseous Diffusion Plant

    International Nuclear Information System (INIS)

    1982-05-01

    The Portsmouth Gaseous Diffusion Plant Air System facilities and operations are reviewed for potential safety problems not covered by standard industrial safety procedures. Information is presented under the following section headings: facility and process description (general); air plant equipment; air distribution system; safety systems; accident analysis; plant air system safety overview; and conclusion

  20. Dipping Strawberry Plants in Fungicides before Planting to Control Anthracnose

    Directory of Open Access Journals (Sweden)

    Myeong Hyeon Nam

    2014-03-01

    Full Text Available Anthracnose crown rot (ACR, caused by Colletotrichum fructicola, is a serious disease of strawberry in Korea. The primary inoculums of ACR were symptomless strawberry plants, plant debris, and other host plants. To effectively control anthracnose in symptomless transplanted strawberries, it is necessary to use diseasefree plants, detect the disease early, and apply a fungicide. Therefore, in 2010 and 2011, we evaluated the efficacy of pre-plant fungicide dips by using strawberry transplants infected by C. fructicola for the control of anthracnose. Dipping plants in prochloraz-Mn for 10 min before planting was most effective for controlling anthracnose in symptomless strawberry plants and resulted in more than 76% control efficacy. Azoxystrobin showed a control efficacy of over 40%, but plants treated with pyraclostrobin, mancozeb and iminoctadine tris showed high disease severity. The control efficacy of the dip treatment with prochloraz-Mn did not differ with temperature and time. Treatment with prochloraz-Mn for more than an hour caused growth suppression in strawberry plants. Therefore, the development of anthracnose can be effectively reduced by dipping strawberry plants for 10 min in prochloraz-Mn before planting.

  1. Plant neurobiology and green plant intelligence : science, metaphors and nonsense

    NARCIS (Netherlands)

    Struik, P.C.; Yin, X.; Meinke, H.B.

    2008-01-01

    This paper analyses the recent debates on the emerging science of plant neurobiology, which claims that the individual green plant should be considered as an intelligent organism. Plant neurobiology tries to use elements from animal physiology as elegant metaphors to trigger the imagination in

  2. Nicotinic plant poisoning.

    Science.gov (United States)

    Schep, Leo J; Slaughter, Robin J; Beasley, D Michael G

    2009-09-01

    A wide range of plants contain nicotinic and nicotinic-like alkaloids. Of this diverse group, those that have been reported to cause human poisoning appear to have similar mechanisms of toxicity and presenting patients therefore have comparable toxidromes. This review describes the taxonomy and principal alkaloids of plants that contain nicotinic and nicotinic-like alkaloids, with particular focus on those that are toxic to humans. The toxicokinetics and mechanisms of toxicity of these alkaloids are reviewed and the clinical features and management of poisoning due to these plants are described. This review was compiled by systematically searching OVID MEDLINE and ISI Web of Science. This identified 9,456 papers, excluding duplicates, all of which were screened. Reviewed plants and their principal alkaloids. Plants containing nicotine and nicotine-like alkaloids that have been reported to be poisonous to humans include Conium maculatum, Nicotiana glauca and Nicotiana tabacum, Laburnum anagyroides, and Caulophyllum thalictroides. They contain the toxic alkaloids nicotine, anabasine, cytisine, n-methylcytisine, coniine, n-methylconiine, and gamma-coniceine. These alkaloids act agonistically at nicotinic-type acetylcholine (cholinergic) receptors (nAChRs). The nicotinic-type acetylcholine receptor can vary both in its subunit composition and in its distribution within the body (the central and autonomic nervous systems, the neuromuscular junctions, and the adrenal medulla). Agonistic interaction at these variable sites may explain why the alkaloids have diverse effects depending on the administered dose and duration of exposure. Nicotine and nicotine-like alkaloids are absorbed readily across all routes of exposure and are rapidly and widely distributed, readily traversing the blood-brain barrier and the placenta, and are freely distributed in breast milk. Metabolism occurs predominantly in the liver followed by rapid renal elimination. Following acute exposure

  3. Aquatic Plant Control Research Program

    National Research Council Canada - National Science Library

    Cofrancesco, Alfred

    1998-01-01

    .... This search for natural plant enemies (insects and fungal pathogens) has led researchers to the native ranges of noxious aquatic plants, located throughout the continents of Africa, Asia, Europe, and Australia...

  4. Emission Facilities - Air Emission Plants

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Represents the Primary Facility type Air Emission Plant (AEP) point features. Air Emissions Plant is a DEP primary facility type related to the Air Quality Program....

  5. Mathematical Modelling Plant Signalling Networks

    KAUST Repository

    Muraro, D.; Byrne, H.M.; King, J.R.; Bennett, M.J.

    2013-01-01

    methods for modelling gene and signalling networks and their application in plants. We then describe specific models of hormonal perception and cross-talk in plants. This mathematical analysis of sub-cellular molecular mechanisms paves the way for more

  6. Table showing nutritional plant list

    African Journals Online (AJOL)

    USER

    2013-04-02

    Apr 2, 2013 ... To consider food as medicine is part of a culture and a millennial human ... propagation, and introduction of nutritionally rich, indigenous plant species in the .... some respondents also mentioned that these plants were being ...

  7. Plant status monitor system description

    International Nuclear Information System (INIS)

    Prather, W.A.; Sly, G.A.

    1987-01-01

    In today's regulatory and financial environment, improving plant efficiency and safety are necessary elements of plant operations. Public utility commissions are making rate rulings based, in part, on plant availability performance; and the NRC is putting more emphasis on plant operational aspects. This comes at a time when operating, maintaining, and managing a plant are becoming increasingly complex; moreover, the desired number of experienced plant personnel are becoming more difficult to find. This situation can be partially resolved by using computer software tools to assist operations, maintenance, engineering, and management personnel. These software tools provide information and interpretations based on plant and equipment status. They support improved plant availability, technical specification compliance, and administrative functions. A key element or computerization is the ability to operate on integrated information

  8. Accommodating for plant modifications

    International Nuclear Information System (INIS)

    Weirich, P.H.

    1977-01-01

    Modification to a nuclear power plant may have different causes: 1) new instructions by the authorities; 2) changes of the marginal conditions on the construction site; 3) progress in the technological development. - Examples from different plants are supposed to demonstrate how such changes influence the planning or the construction and how they are integrated in the process of preparation. A distinction can be made between modifications before the completion of the submission of the order, during the phase of preparatory planning and during the construction phase. Of great importance are especially modifications made after the beginning of the construction works, since, in general, there is little scope for technical modifications and since consequences for the time schedule are to be expected. (orig.) [de

  9. Integrated turbomachine oxygen plant

    Science.gov (United States)

    Anand, Ashok Kumar; DePuy, Richard Anthony; Muthaiah, Veerappan

    2014-06-17

    An integrated turbomachine oxygen plant includes a turbomachine and an air separation unit. One or more compressor pathways flow compressed air from a compressor through one or more of a combustor and a turbine expander to cool the combustor and/or the turbine expander. An air separation unit is operably connected to the one or more compressor pathways and is configured to separate the compressed air into oxygen and oxygen-depleted air. A method of air separation in an integrated turbomachine oxygen plant includes compressing a flow of air in a compressor of a turbomachine. The compressed flow of air is flowed through one or more of a combustor and a turbine expander of the turbomachine to cool the combustor and/or the turbine expander. The compressed flow of air is directed to an air separation unit and is separated into oxygen and oxygen-depleted air.

  10. Nuclear plant license renewal

    International Nuclear Information System (INIS)

    Gazda, P.A.; Bhatt, P.C.

    1991-01-01

    During the next 10 years, nuclear plant license renewal is expected to become a significant issue. Recent Electric Power Research Institute (EPRI) studies have shown license renewal to be technically and economically feasible. Filing an application for license renewal with the Nuclear Regulatory Commission (NRC) entails verifying that the systems, structures, and components essential for safety will continue to perform their safety functions throughout the license renewal period. This paper discusses the current proposed requirements for this verification and the current industry knowledge regarding age-related degradation of structures. Elements of a license renewal program incorporating NRC requirements and industry knowledge including a schedule are presented. Degradation mechanisms for structural components, their significance to nuclear plant structures, and industry-suggested age-related degradation management options are also reviewed

  11. The Chernobyl plant shutdown

    International Nuclear Information System (INIS)

    2000-12-01

    The Chernobylsk-1 reactor, operational in september 1977 has been stopped in november 1996; the Chernobylsk-2 reactor started in november 1978 is out of order since 1991 following a fire. The Chernobylsk-3 reactor began in 1981. During the last three years it occurs several maintenance operations that stop it. In june 2000, the Ukrainian authorities decided to stop it definitively on the 15. of december (2000). This file handles the subject. it is divided in four chapters: the first one gives the general context of the plant shutdown, the second chapter studies the supporting projects to stop definitively the nuclear plant, the third chapter treats the question of the sarcophagus, and the fourth and final chapter studies the consequences of the accident and the contaminated territories. (N.C.)

  12. Power plant simulation

    Energy Technology Data Exchange (ETDEWEB)

    Hacking, D [Marconi Simulation (United Kingdom)

    1992-09-01

    Over many years in the field of simulation Marconi has developed and adopted a number of procedures and methodologies for the management, design and development of an extensive range of training equipment. This equipment encompasses desktop computer-based training systems, generic training devices. The procurement of a training simulator is clearly dictated by the perceived training requirement or problem. Also, it should preferably involve or follow a detailed training needs analysis. Although the cost benefits of training are often difficult to quantify, a simulator is frequently easier to justify if plant familiarisation and training can be provided in advance of on-the-job experience. This is particularly true if the target operators have little hands-on experience of similar plant either in terms of processes or the operator interface. (author).

  13. Radiosensitivity of higher plants

    International Nuclear Information System (INIS)

    Feng Zhijie

    1992-11-01

    The general views on radiosensitivity of higher plants have been introduced from published references. The radiosensitivity varies with species, varieties and organs or tissues. The main factors of determining the radiosensitivity in different species are nucleus volume, chromosome volume, DNA content and endogenous compounds. The self-repair ability of DNA damage and chemical group of biological molecules, such as -SH thiohydroxy of proteins, are main factors to determine the radiosensitivity in different varieties. The moisture, oxygen, temperature radiosensitizer and protector are important external factors for radiosensitivity. Both the multiple target model and Chadwick-Leenhouts model are ideal mathematical models for describing the radiosensitivity of higher plants and the latter has more clear significance in biology

  14. Nuclear power plant

    International Nuclear Information System (INIS)

    Aisaka, Tatsuyoshi; Kamahara, Hisato; Yanagisawa, Ko.

    1982-01-01

    Purpose: To prevent corrosion stress cracks in structural materials in a BWR type nuclear power plant by decreasing the oxygen concentration in the reactor coolants. Constitution: A hydrogen injector is connected between the condensator and a condensate clean up system of a nuclear power plant. The injector is incorporated with hydrogenated compounds formed from metal hydrides, for example, of alloys such as lanthanum-nickel alloy, iron titanium alloy, vanadium, palladium, magnesium-copper alloy, magnesium-nickel alloy and the like. Even if the pressure of hydrogen obtained from a hydrogen bomb or by way of water electrolysis is changed, the hydrogen can always be injected into a reactor coolant at a pressure equal to the equilibrium dissociation pressure for metal hydride by introducing the hydrogen into the hydrogen injector. (Seki, T.)

  15. Mobile power plant units

    Energy Technology Data Exchange (ETDEWEB)

    Radtke, R

    1979-10-05

    Diesel engines of the MaK line 282 AK/332 with a cylinder power up to 160 kW are used, either as 6-cylinder or 8-cylinder in-line engine or as 12-cylinder V engine. Fuel consumption is between 207 and 212 g/kW. The engine is mounted on a frame, together with a generator. The fuel reserve in the tank will last for 8 hours. The lubricating system, the cooling water and starting air system, the switchboard system, and the frame are described. The switchboard plant is mounted either on a skid undercarriage or on the undercarriage. The plant can be operated independently or parallel to the network. The unit can be remote-controlled via push buttons or control knobs. A picture is presented of a mobile diesel aggregate which is in service in Libya.

  16. Dry alcohol production plant

    Directory of Open Access Journals (Sweden)

    Stanković Mirjana S.

    2003-01-01

    Full Text Available The IGPC Engineering Department designed basic projects for dry alcohol production plant, using technology developed in the IGPC laboratories. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects a production plant with a capacity of 40 m3/y was manufactured, at "Zorka Pharma", Šabac in 1995-1996. The product meets all quality demands, as well as environmental regulations. The dry alcohol production process is fully automatized. There is no waste in the process, neither gaseous, nor liquid. The chosen process provides safe operation according to temperature regime and resistance in the pipes, air purification columns and filters. Working at increased pressure is suitable for evaporation and condensation at increased temperatures. The production process can be controlled manually, which is necessary during start-up, and repairs.

  17. Tritium in plants

    International Nuclear Information System (INIS)

    Vichot, L.; Losset, Y.

    2009-01-01

    The presence of tritium in the environment stems from its natural production by cosmic rays, from the fallout of the nuclear weapon tests between 1953 and 1964, and locally from nuclear industry activities. A part of the tritiated water contained in the foliage of plants is turned into organically bound tritium (OBT) by photosynthesis. The tritium of OBT, that is not exchangeable and then piles up in the plant, can be used as a marker of the past. It has been shown that the quantity of OBT contained in the age-rings of an oak that grew near the CEA center of Valduc was directly correlated with the tritium releases of the center. (A.C.)

  18. Third generation nuclear plants

    Science.gov (United States)

    Barré, Bertrand

    2012-05-01

    After the Chernobyl accident, a new generation of Light Water Reactors has been designed and is being built. Third generation nuclear plants are equipped with dedicated systems to insure that if the worst accident were to occur, i.e. total core meltdown, no matter how low the probability of such occurrence, radioactive releases in the environment would be minimal. This article describes the EPR, representative of this "Generation III" and a few of its competitors on the world market.

  19. The intelligent plant

    Energy Technology Data Exchange (ETDEWEB)

    Bruce Firth [CSIRO Energy Technology (Australia)

    2009-06-15

    The current advances in electronics and smart sensors, coupled with the large amount of information that modern distributed control systems can create, provide opportunities but posses some significant problems. The potential suite of data measurements could provide plant operators, maintenance staff and supervisors with a comprehensive understanding of the current health of a coal preparation plant. Analysis of this issue would also provide a tool for the recognition of where important data is not or poorly (timeframe and/or quality) currently available. A suitable system for categorisation of the information associated with the description of the 'Health of a Plant' has been developed. A relational data base model for these categories was derived. The process and performance information relationships were established via the use of models derived from the wide body of literature available. Given the availability of the above model relationships and measurements, the best way to utilise this information in a simple intelligent manner was addressed. It involved the construction of a high level fuzzy set diagnosis chart and an underlying set of unit operation diagnostic charts. These charts provided the basis for the implementation of a generic diagnosis system. This was deliberately developed in EXCEL so that it can be used and/or modified to suit a particular plant. A sensing system which combines a limited set of measurements with an algorithm or logic system for optimisation of a process can be termed a smart sensor. These are vey useful in the optimisation of difficult process situations, and can be used to supplement expert systems. It is believed that the models developed in this project can also provide the basis for appropriate smart sensors when access to appropriate measurements is available.

  20. Nuclear power plant

    International Nuclear Information System (INIS)

    Schabert, H.P.; Laurer, E.

    1976-01-01

    The invention concerns a quick-acting valve on the main-steam pipe of a nuclear power plant. The engineering design of the valve is to be improved. To the main valve disc, a piston-operated auxiliary valve disc is to be assigned closing a section of the area of the main valve disc. This way it is avoided that the drive of the main valve disc has to carry out different movements. 15 sub-claims. (UWI) [de

  1. Fusion power plant economics

    International Nuclear Information System (INIS)

    Miller, R.L.

    1996-01-01

    The rationale, methodology, and updated comparative results of cost projections for magnetic-fusion-energy central-station electric power plants are considered. Changing market and regulatory conditions, particularly in the U.S., prompt fundamental reconsideration of what constitutes a competitive future energy-source technology and has implications for the direction and emphasis of appropriate near-term research and development programs, for fusion and other advanced generation systems. 36 refs., 2 figs., 2 tabs

  2. Parasites, Plants, and People.

    Science.gov (United States)

    Johnson, Marion; Moore, Tony

    2016-06-01

    Anthelminthic resistance is acknowledged worldwide and is a major problem in Aotearoa New Zealand, thus alternative parasite management strategies are imperative. One Health is an initiative linking animal, human, and environmental health. Parasites, plants, and people illustrate the possibilities of providing diverse diets for stock thereby lowering parasite burdens, improving the cultural wellbeing of a local community, and protecting the environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Power plant emissions reduction

    Science.gov (United States)

    Anand, Ashok Kumar; Nagarjuna Reddy, Thirumala Reddy

    2015-10-20

    A system for improved emissions performance of a power plant generally includes an exhaust gas recirculation system having an exhaust gas compressor disposed downstream from the combustor, a condensation collection system at least partially disposed upstream from the exhaust gas compressor, and a mixing chamber in fluid communication with the exhaust gas compressor and the condensation collection system, where the mixing chamber is in fluid communication with the combustor.

  4. Automation of solar plants

    Energy Technology Data Exchange (ETDEWEB)

    Yebra, L.J.; Romero, M.; Martinez, D.; Valverde, A. [CIEMAT - Plataforma Solar de Almeria, Tabernas (Spain); Berenguel, M. [Almeria Univ. (Spain). Departamento de Lenguajes y Computacion

    2004-07-01

    This work overviews some of the main activities and research lines that are being carried out within the scope of the specific collaboration agreement between the Plataforma Solar de Almeria-CIEMAT (PSA-CIEMAT) and the Automatic Control, Electronics and Robotics research group of the Universidad de Almeria (TEP197) titled ''Development of control systems and tools for thermosolar plants'' and the projects financed by the MCYT DPI2001-2380-C02-02 and DPI2002-04375-C03. The research is directed by the need of improving the efficiency of the process through which the energy provided by the sun is totally or partially used as energy source, as far as diminishing the costs associated to the operation and maintenance of the installations that use this energy source. The final objective is to develop different automatic control systems and techniques aimed at improving the competitiveness of solar plants. The paper summarizes different objectives and automatic control approaches that are being implemented in different facilities at the PSA-CIEMAT: central receiver systems and solar furnace. For each one of these facilities, a systematic procedure is being followed, composed of several steps: (i) development of dynamic models using the newest modeling technologies (both for simulation and control purposes), (ii) development of fully automated data acquisition and control systems including software tools facilitating the analysis of data and the application of knowledge to the controlled plants and (iii) synthesis of advanced controllers using techniques successfully used in the process industry and development of new and optimized control algorithms for solar plants. These aspects are summarized in this work. (orig.)

  5. Antibodies from plants for bionanomaterials

    OpenAIRE

    Edgue, G.; Twyman, R.M.; Beiss, V.; Fischer, R.; Sack, M.

    2017-01-01

    Antibodies are produced as part of the vertebrate adaptive immune response and are not naturally made by plants. However, antibody DNA sequences can be introduced into plants, and together with laboratory technologies that allow the design of antibodies recognizing any conceivable molecular structure, plants can be used as green factories' to produce any antibody at all. The advent of plant-based transient expression systems in particular allows the rapid, convenient, and safe production of a...

  6. Plant Pathogenicity in Spaceflight Environments

    OpenAIRE

    Bishop, Deborah L.; Levine, Howard G.; Anderson, Anne J.

    1996-01-01

    Plants grown in microgravity are subject to many environmental stresses, which may promote microbial growth and result in pathogenicity to the plant. Recent plant experiments with super dwarf wheat aboard the NASA Space Shuttle and NASA/Russian Mir Space Station returned from the mission with severe degrees of fungal contamination. Understanding the cause of such microbial contamination and methods to eliminate it are necessary prerequisites for continued plant growth and development studies ...

  7. On nuclear power plant uprating

    International Nuclear Information System (INIS)

    Ho, S. Allen; Bailey, James V.; Maginnis, Stephen T.

    2004-01-01

    Power uprating for commercial nuclear power plants has become increasingly attractive because of pragmatic reasons. It provides quick return on investment and competitive financial benefits, while involving low risks regarding plant safety and public objection. This paper briefly discussed nuclear plant uprating guidelines, scope for design basis analysis and engineering evaluation, and presented the Salem nuclear power plant uprating study for illustration purposes. A cost and benefit evaluation of the Salem power uprating was also included. (author)

  8. From plant genomes to phenotypes

    OpenAIRE

    Bolger, Marie; Gundlach, Heidrun; Scholz, Uwe; Mayer, Klaus; Usadel, Björn; Schwacke, Rainer; Schmutzer, Thomas; Chen, Jinbo; Arend, Daniel; Oppermann, Markus; Weise, Stephan; Lange, Matthias; Fiorani, Fabio; Spannagl, Manuel

    2017-01-01

    Recent advances in sequencing technologies have greatly accelerated the rate of plant genome and applied breeding research. Despite this advancing trend, plant genomes continue to present numerous difficulties to the standard tools and pipelines not only for genome assembly but also gene annotation and downstream analysis.Here we give a perspective on tools, resources and services necessary to assemble and analyze plant genomes and link them to plant phenotypes.

  9. Deep Learning for Plant Phenotyping

    OpenAIRE

    Mori, Matteo

    2016-01-01

    Plant Phenotyping is an emerging science which provides us the knowledge to better understand plants. Indeed, the study of the link between genetic background and environment in which plants develop can help us to determine cures for plants’ sicknesses and new ways to improve yields using limited resources. In this regard, one of the main aspects of Plant Phenotyping that were studied in the past, was Root Phenotyping, which is based on the study of the root architectures. In particular, toda...

  10. Process Experimental Pilot Plant

    International Nuclear Information System (INIS)

    Henze, H.

    1986-01-01

    The Process Experimental Pilot Plant (PREPP) at the Idaho National Engineering Laboratory (INEL) was built to convert transuranic contaminated solid waste into a form acceptable for disposal at the Waste Isolation Pilot Plant (WIPP), located near Carlsbad, New Mexico. There are about 2.0 million cubic ft of transuranic waste stored at the Transuranic Storage Area of the INEL's Radioactive Waste Management Complex (RWMC). The Stored Waste Examination Pilot Plant (SWEPP) located at the RWMC will examine this stored transuranic waste to determine if the waste is acceptable for direct shipment to and storage at WIPP, or if it requires shipment to PREPP for processing before shipment to WIPP. The PREPP process shreds the waste, incinerates the shredded waste, and cements (grouts) the shredded incinerated waste in new 55-gal drums. Unshreddable items are repackaged and returned to SWEPP. The process off-gas is cleaned prior to its discharge to the atmosphere, and complies with the effluent standards of the State of Idaho, EPA, and DOE. Waste liquid generated is used in the grouting operation

  11. Waste incinerating plant

    Energy Technology Data Exchange (ETDEWEB)

    1972-12-01

    This plant is provided with a NKK-Ferunst type reciprocating stage fire lattice which has a good ventilating effect and a proper stirring and loosening effect, achieving a high combustion rate, and has also a gas flow system by which gas can flow in the reverse direction to adjust its flow for seasonal variations in the quality of waste. Also, a room in which the exhaust gas is mixed is provided in this plant as a help for the complete neutralization and combustion of acid gas such as hydrogen chloride and imperfect combustion gas from plastic waste contained in wastes. In this system, waste can accept a sufficient radiant heat from the combustion gas, the furnace wall, and the ceiling; even on the post combustion fire lattice the ashes are given heat enough to complete the post combustion, so that it can be completely reduced to ashes. For these reasons, this type of incinerator is suitable for the combustion of low-calorie wastes such as city wastes. The harmful gases resulting from the combustion of wastes are treated completely by desulfurization equipment which can remove the oxides of sulfur. This type of plant also can dispose of a wide variety of wastes, and is available in several capacities from 30 tons per 8 hr to 1,200 tons per 24 hr.

  12. Genetics and plant development.

    Science.gov (United States)

    Prunet, Nathanaël; Meyerowitz, Elliot M

    2016-01-01

    There are only three grand theories in biology: the theory of the cell, the theory of the gene, and the theory of evolution. Two of these, the cell and gene theories, originated in the study of plants, with the third resulting in part from botanical considerations as well. Mendel's elucidation of the rules of inheritance was a result of his experiments on peas. The rediscovery of Mendel's work in 1900 was by the botanists de Vries, Correns, and Tschermak. It was only in subsequent years that animals were also shown to have segregation of genetic elements in the exact same manner as had been shown in plants. The story of developmental biology is different - while the development of plants has long been studied, the experimental and genetic approaches to developmental mechanism were developed via experiments on animals, and the importance of genes in development (e.g., Waddington, 1940) and their use for understanding developmental mechanisms came to botanical science much later - as late as the 1980s. Copyright © 2016 Académie des sciences. Published by Elsevier SAS. All rights reserved.

  13. Beloyarsk Nuclear Power Plant

    International Nuclear Information System (INIS)

    1997-01-01

    The Beloyarsk Nuclear Power Plant (BNPP) is located in Zarechny, approximately 60 km east of Ekaterinberg along the Trans-Siberian Highway. Zarechny, a small city of approximately 30,000 residents, was built to support BNPP operations. It is a closed city to unescorted visitors. Residents must show identification for entry. BNPP is one of the first and oldest commercial nuclear power plants in Russia and began operations in 1964. As for most nuclear power plants in the Russian Federation, BNPP is operated by Rosenergoatom, which is subordinated to the Ministry of Atomic Energy of the Russian Federation (Minatom). BNPP is the site of three nuclear reactors, Units 1, 2, and 3. Units 1 and 2, which have been shut-down and defueled, were graphite moderated reactors. The units were shut-down in 1981 and 1989. Unit 3, a BN-600 reactor, is a 600 MW(electric) sodium-cooled fast breeder reactor. Unit 3 went on-line in April 1980 and produces electric power which is fed into a distribution grid and thermal power which provides heat to Zarechny. The paper also discusses the SF NIKIET, the Sverdiovsk Branch of NIKIET, Moscow, which is the research and development branch of the parent NIKEIT and is primarily a design institute responsible for reactor design. Central to its operations is a 15 megawatt IVV research reactor. The paper discusses general security and fissile material control and accountability at these two facilities

  14. Profitability of irradiation plants

    International Nuclear Information System (INIS)

    Bustos R, M.E.; Gonzalez F, C.; Liceaga C, G.; Ortiz A, G.

    1997-01-01

    In any industrial process it is seek an attractive profit from the contractor and the social points of view. The use of the irradiation technology in foods allows keep their hygienically, which aid to food supply without risks for health, an increment of new markets and a losses reduction. In other products -cosmetics or disposable for medical use- which are sterilized by irradiation, this process allows their secure use by the consumers. The investment cost of an irradiation plant depends mainly of the plant size and the radioactive material reload that principally is Cobalt 60, these two parameters are in function of the type of products for irradiation and the selected doses. In this work it is presented the economic calculus and the financial costs for different products and capacities of plants. In general terms is determined an adequate utility that indicates that this process is profitable. According to the economic and commercial conditions in the country were considered two types of credits for the financing of this projects. One utilizing International credit resources and other with national sources. (Author)

  15. Communal biomass conversion plants

    International Nuclear Information System (INIS)

    1991-06-01

    The Coordinating Committee set up by the Danish government in 1986 were given the responsibility of investigating the potentials for biomass conversion plants in Denmark, especially in relation to agricultural, environmental and energy aspects. The results of the Committee's plan of management for this project are presented. This main report covers 13 background reports which deal with special aspects in detail. The report describes the overall plan of management, the demonstration and follow-up programme and the individual biogas demonstration plants. Information gained from these investigations is presented. The current general status, (with emphasis on the technical and economical aspects) and the prospects for the future are discussed. The interest other countries have shown in Danish activities within the field of biogas production is described, and the possibilities for Danish export of technology and know-how in this relation are discussed. It is claimed that Denmark is the first country that has instigated a coordinated development programme for biomass conversion plants. (AB) 24 refs

  16. Seeding and planting upland oaks

    Science.gov (United States)

    1989-01-01

    Oaks can be planted or seeded in uplands to: (1) afforest old fields, strip-mined areas, or other areas devoid of trees, and (2) supplement natural reproduction within existing forests. Planting is usually more successful than direct seeding. But even under good conditions survival and growth of planted oak has been considerably poorer than with conifers and other...

  17. Regulating nutrient allocation in plants

    Science.gov (United States)

    Udvardi, Michael; Yang, Jiading; Worley, Eric

    2014-12-09

    The invention provides coding and promoter sequences for a VS-1 and AP-2 gene, which affects the developmental process of senescence in plants. Vectors, transgenic plants, seeds, and host cells comprising heterologous VS-1 and AP-2 genes are also provided. Additionally provided are methods of altering nutrient allocation and composition in a plant using the VS-1 and AP-2 genes.

  18. Try This: Plant Leaf Exploration

    Science.gov (United States)

    Preston, Christine

    2017-01-01

    Plants are often overlooked in favour of animals when teaching about living things. Focusing on familiar animals that share human characteristics helps young children learn about similar features. Examining plants for their differences, though, helps foster wonder. In the author's experience, children find it intriguing that plants need…

  19. Global Activities and Plant Survival

    DEFF Research Database (Denmark)

    Bandick, Roger

    2014-01-01

    the highest exit rates. Moreover, the exit rates of globally engaged plants seem to be unaffected by increased foreign presence, whereas there appears to be a negative impact on the survival rates of non-exporting non-MNE plants. Finally, the result reveals that the survival ratio of plants of acquired...

  20. PERSPECTIVE IN PLANT DRUG RESEARCH

    Science.gov (United States)

    Singh, R.H.; Singh, K.P.

    1990-01-01

    Plant medicine becomes more popular thought the world in these days probably of its latest toxicity. Ayurveda that leads in plant medicine preserves the natural form of herbs maximum, in various pharmaceutical preparations. Isolation of active principles has not proved much fruitful. However, the need of hour is cultivation of more medicinal plants along with popularization of their use traditional simpler forms. PMID:22557691

  1. Selected Landscape Plants. Slide Script.

    Science.gov (United States)

    McCann, Kevin

    This slide script, part of a series of slide scripts designed for use in vocational agriculture classes, deals with commercially important woody ornamental landscape plants. Included in the script are narrations for use with a total of 253 slides illustrating 92 different plants. Several slides are used to illustrate each plant: besides a view of…

  2. Gamma irradiation plants using reactor fuel elements

    International Nuclear Information System (INIS)

    Suckow, W.

    1976-11-01

    Recent irradiation plants utilizing fuel elements are described. Criteria for optimizing such plants, evaluation of the plants realized so far, and applications for the facilities are discussed. (author)

  3. Four planting devices for planting no-till maize

    Directory of Open Access Journals (Sweden)

    Osei Bonsu Patterson

    2015-05-01

    Full Text Available An experiment was conducted at the CSIR-Crops Research Institute (CSIR-CRI Experimental station at Ejura in Ghana to compare the efficiency of four devices for planting no-till maize: Tractor drawn seeder, Chinese made jab planter, Locally made jab planter and a Cutlass. It took two (2 hours 48 minutes to plant one hectare of maize with the tractor drawn seeder, which was significantly (p less than 1% faster than all the planting methods. Cutlass was the slowest planting device lasting more than 14 hours per hectare. There was no significant difference in planting time between the Chinese planter and local planter. Economic analysis showed that cutlass planting produced the highest net benefit, whilst tractor drawn seeder produced the least benefit. In this study cutlass planting was done with precision by collaborating farmers. In actual farm situation however, hired laborers (planting gangs often plant in haste which often results in poor plant population leading to low yields. Tractor drawn seeders or jab planters could reduce drudgery in planting and encourage farm expansion.

  4. Regulatory requirements for desalination plant coupled with nuclear reactor plant

    International Nuclear Information System (INIS)

    Yune, Young Gill; Kim, Woong Sik; Jo, Jong Chull; Kim, Hho Jung; Song, Jae Myung

    2005-01-01

    A small-to-medium sized reactor has been developed for multi-purposes such as seawater desalination, ship propulsion, and district heating since early 1990s in Korea. Now, the construction of its scaled-down research reactor, equipped with a seawater desalination plant, is planned to demonstrate the safety and performance of the design of the multi-purpose reactor. And the licensing application of the research reactor is expected in the near future. Therefore, a development of regulatory requirements/guides for a desalination plant coupled with a nuclear reactor plant is necessary for the preparation of the forthcoming licensing review of the research reactor. In this paper, the following contents are presented: the design of the desalination plant, domestic and foreign regulatory requirements relevant to desalination plants, and a draft of regulatory requirements/guides for a desalination plant coupled with a nuclear reactor plant

  5. Arabinogalactan proteins in plants

    Directory of Open Access Journals (Sweden)

    Ewa Szczuka

    2013-04-01

    Full Text Available AGPs (arabinogalactan-proteins are the major constituent of arabic gum and have been used as emulsifiers and stabilizing agents. They are also one of the most abundant and heterogeneous class forming a large family of proteoglycans that sculpt the surface not only of plant but also of all eukaryotic cells. Undoubtedly, AGPs appear in numerous biological processes, playing diverse functions. Despite their abundance in nature and industrial utility, the in vivofunction(s of AGPs still remains unclear or even unknown. AGPs are commonly distributed in different plant organs and probably participate in all aspects of plant growth and development including reproduction (e.g. they are present in the stigma including stigma exudates, and in transmitting tissues in styles, pollen grains, and pollen tubes. The functions and evident involvement of AGPs in sexual plant reproduction in a few plant species as Actinidia deliciosa (A.Chev. C.F.Liang & A.R.Ferguson, Amaranthus hypochondriacus L., Catharanthus roseus (L. G.Don, Lolium perenneL. and Larix deciduaMill. are known from literature. The localization of two kinds of AGP epitopes, recognized by the JIM8 and JIM13 mAbs, in anatomically different ovules revealed some differences in spatial localization of these epitopes in ovules of monocots Galanthus nivalis L. and Galtonia candicans (Baker Decne. and dicots like Oenothera species and Sinapis albaL. A detailed study of the localization of AGPs in egg cells, zygotes, including the zygote division stage, and in two-celled proembryos in Nicotiana tabacumL. prompts consideration of the necessity of their presence in the very early steps of ontogenesis. The selective labeling obtained with AGP mAbs JIM8, JIM13, MAC207, and LM2 during Arabidopsis thaliana(L. Heynh. development suggests that some AGPs can be regarded as molecular markers for gametophytic cell differentiation. Moreover, the results show evident differences in the distribution of specific AGP

  6. Plant ecdysteroids: plant sterols with intriguing distributions, biological effects and relations to plant hormones.

    Science.gov (United States)

    Tarkowská, Danuše; Strnad, Miroslav

    2016-09-01

    The present review summarises current knowledge of phytoecdysteroids' biosynthesis, distribution within plants, biological importance and relations to plant hormones. Plant ecdysteroids (phytoecdysteroids) are natural polyhydroxylated compounds that have a four-ringed skeleton, usually composed of either 27 carbon atoms or 28-29 carbon atoms (biosynthetically derived from cholesterol or other plant sterols, respectively). Their physiological roles in plants have not yet been confirmed and their occurrence is not universal. Nevertheless, they are present at high concentrations in various plant species, including commonly consumed vegetables, and have a broad spectrum of pharmacological and medicinal properties in mammals, including hepatoprotective and hypoglycaemic effects, and anabolic effects on skeletal muscle, without androgenic side-effects. Furthermore, phytoecdysteroids can enhance stress resistance by promoting vitality and enhancing physical performance; thus, they are considered adaptogens. This review summarises current knowledge of phytoecdysteroids' biosynthesis, distribution within plants, biological importance and relations to plant hormones.

  7. Beaver herbivory on aquatic plants.

    Science.gov (United States)

    Parker, John D; Caudill, Christopher C; Hay, Mark E

    2007-04-01

    Herbivores have strong impacts on marine and terrestrial plant communities, but their impact is less well studied in benthic freshwater systems. For example, North American beavers (Castor canadensis) eat both woody and non-woody plants and focus almost exclusively on the latter in summer months, yet their impacts on non-woody plants are generally attributed to ecosystem engineering rather than herbivory. Here, we excluded beavers from areas of two beaver wetlands for over 2 years and demonstrated that beaver herbivory reduced aquatic plant biomass by 60%, plant litter by 75%, and dramatically shifted plant species composition. The perennial forb lizard's tail (Saururus cernuus) comprised less than 5% of plant biomass in areas open to beaver grazing but greater than 50% of plant biomass in beaver exclusions. This shift was likely due to direct herbivory, as beavers preferentially consumed lizard's tail over other plants in a field feeding assay. Beaver herbivory also reduced the abundance of the invasive aquatic plant Myriophyllum aquaticum by nearly 90%, consistent with recent evidence that native generalist herbivores provide biotic resistance against exotic plant invasions. Beaver herbivory also had indirect effects on plant interactions in this community. The palatable plant lizard's tail was 3 times more frequent and 10 times more abundant inside woolgrass (Scirpus cyperinus) tussocks than in spatially paired locations lacking tussocks. When the protective foliage of the woolgrass was removed without exclusion cages, beavers consumed nearly half of the lizard's tail leaves within 2 weeks. In contrast, leaf abundance increased by 73-93% in the treatments retaining woolgrass or protected by a cage. Thus, woolgrass tussocks were as effective as cages at excluding beaver foraging and provided lizard's tail plants an associational refuge from beaver herbivory. These results suggest that beaver herbivory has strong direct and indirect impacts on populations and

  8. Autophagy in plant pathogenic fungi.

    Science.gov (United States)

    Liu, Xiao-Hong; Xu, Fei; Snyder, John Hugh; Shi, Huan-Bin; Lu, Jian-Ping; Lin, Fu-Cheng

    2016-09-01

    Autophagy is a conserved cellular process that degrades cytoplasmic constituents in vacuoles. Plant pathogenic fungi develop special infection structures and/or secrete a range of enzymes to invade their plant hosts. It has been demonstrated that monitoring autophagy processes can be extremely useful in visualizing the sequence of events leading to pathogenicity of plant pathogenic fungi. In this review, we introduce the molecular mechanisms involved in autophagy. In addition, we explore the relationship between autophagy and pathogenicity in plant pathogenic fungi. Finally, we discuss the various experimental strategies available for use in the study of autophagy in plant pathogenic fungi. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. B plant mission analysis report

    International Nuclear Information System (INIS)

    Lund, D.P.

    1995-01-01

    This report further develops the mission for B Plant originally defined in WHC-EP-0722, ''System Engineering Functions and Requirements for the Hanford Cleanup Mission: First Issue.'' The B Plant mission analysis will be the basis for a functional analysis that breaks down the B Plant mission statement into the necessary activities to accomplish the mission. These activities are the product of the functional analysis and will then be used in subsequent steps of the systems engineering process, such as identifying requirements and allocating those requirements to B Plant functions. The information in this mission analysis and the functional and requirements analysis are a part of the B Plant technical baseline

  10. The plants in the Florilegia

    DEFF Research Database (Denmark)

    Arnklit, Folmer; Frederiksen, Signe; Hansen, Hans Vilhelm

    2013-01-01

    The Gottorfer Codex and The Green Florilegium contain a total of more than 1,500 pictures of plants. In this article the botanists who recently identified the plants in the two albums take a look at the works as seen through the eyes of a botanist. Based on their knowledge of the plants behind...... the pictures the authors shed light on a range of different aspects, e.g. the relationship between figures and real plants and the horticultural background of the plants. They also offer botanical explanations for peculiarities such as double and proliferous flowers....

  11. Towards Multi Fuel SOFC Plant

    DEFF Research Database (Denmark)

    Rokni, Masoud; Clausen, Lasse Røngaard; Bang-Møller, Christian

    2011-01-01

    Complete Solid Oxide Fuel Cell (SOFC) plants fed by several different fuels are suggested and analyzed. The plants sizes are about 10 kW which is suitable for single family house with needs for both electricity and heat. Alternative fuels such as, methanol, DME (Di-Methyl Ether) and ethanol...... are also considered and the results will be compared with the base plant fed by Natural Gas (NG). A single plant design will be suggested that can be fed with methanol, DME and ethanol whenever these fuels are available. It will be shown that the plant fed by ethanol will have slightly higher electrical...

  12. Aquatic Plant Control Research Program. Allelopathic Aquatic Plants for Aquatic Plant Management: A Feasibility Study

    Science.gov (United States)

    1989-10-01

    1978. " Ecotoxicology of aquatic plant communi- ties," Principles of Ecotoxicology , SCOPE Report 12, Chapter 11, pp 239-255. [Heavy metals, Pollutants...Phragmites communis and Equisetum limosum were cultivated . They found plant-plant influences depend on soil type. Typha latifolia, S. A2 lacustris, and

  13. Plant-plant competition outcomes are modulated by plant effects on the soil bacterial community.

    Science.gov (United States)

    Hortal, S; Lozano, Y M; Bastida, F; Armas, C; Moreno, J L; Garcia, C; Pugnaire, F I

    2017-12-19

    Competition is a key process that determines plant community structure and dynamics, often mediated by nutrients and water availability. However, the role of soil microorganisms on plant competition, and the links between above- and belowground processes, are not well understood. Here we show that the effects of interspecific plant competition on plant performance are mediated by feedbacks between plants and soil bacterial communities. Each plant species selects a singular community of soil microorganisms in its rhizosphere with a specific species composition, abundance and activity. When two plant species interact, the resulting soil bacterial community matches that of the most competitive plant species, suggesting strong competitive interactions between soil bacterial communities as well. We propose a novel mechanism by which changes in belowground bacterial communities promoted by the most competitive plant species influence plant performance and competition outcome. These findings emphasise the strong links between plant and soil communities, paving the way to a better understanding of plant community dynamics and the effects of soil bacterial communities on ecosystem functioning and services.

  14. Phytochrome, plant growth and flowering

    Science.gov (United States)

    King, R. W.; Bagnall, D. J.

    1994-01-01

    Attempts to use artificially lit cabinets to grow plants identical to those growing in sunlight have provided compelling evidence of the importance of light quality for plant growth. Changing the balance of red (R) to far-red (FR) radiation, but with a fixed photosynthetic input can shift the phytochrome photoequilibrium in a plant and generate large differences in plant growth. With FR enrichment the plants elongate, and may produce more leaf area and dry matter. Similar morphogenic responses are also obtained when light quality is altered only briefly (15-30 min) at the end-of-the-day. Conversely, for plants grown in natural conditions the response of plant form to selective spectral filtering has again shown that red and far-red wavebands are important as found by Kasperbauer and coworkers. Also, where photosynthetic photon flux densities (PPFD) of sunlight have been held constant, the removal of far-red alone alters plant growth. With FR depletion plants grown in sunlight are small, more branched and darker green. Here we examine the implications for plant growth and flowering when the far-red composition of incident radiation in plant growth chambers is manipulated.

  15. The year 2000 power plant

    International Nuclear Information System (INIS)

    Roman, H.T.

    1989-01-01

    Every utility seeks extended service life from its existing power plants before building new ones. It is not easy to justify a new power plant. The licensing and cost of new plants have become uncertain. In response to these conditions, electric utilities are undertaking plant life-extension studies and, in some cases, reconditioning/upgrading old power plants to significantly increase useful service life. Other technologies like robotics and artificial intelligence/expert systems are also being developed to reduce operating and maintenance (O and M) expenses, to remove workers from potentially hazardous environments, and to reduce plant downtime. Together, these steps represent an interim solution, perhaps providing some relief for the next few decades. However, there are serious physical and economic limits to retrofitting new technology into existing power plants. Some old plants will simply be beyond their useful life and require retirement. In nuclear plants, for instance, retrofit may raise important and time-consuming licensing/safety issues. Based on their robotics and artificial intelligence experience, the authors of this article speculate bout the design of the year 2000 power plant - a power plant they feel will naturally incorporate liberal amounts of robotic and artificial intelligence technologies

  16. Phytochrome, plant growth and flowering

    Energy Technology Data Exchange (ETDEWEB)

    King, R.W.; Bagnall, D.J. [CSIRO, Canberra (Australia)

    1994-12-31

    Attempts to use artificially lit cabinets to grow plants identical to those growing in sunlight have provided compelling evidence of the importance of light quality for plant growth. Changing the balance of red (R) to far-red (FR) radiation, but with a fixed photosynthetic input can shift the phytochrome photoequilibrium in a plant and generate large differences in plant growth. With FR enrichment the plants elongate, and may produce more leaf area and dry matter. Similar morphogenic responses are also obtained when light quality is altered only briefly (15-30 min) at the end-of-the-day. Conversely, for plants grown in natural conditions the response of plant form to selective spectral filtering has again shown that red and far-red wavebands are important as found by Kasperbauer and coworkers. Also, where photosynthetic photon flux densities (PPFD) of sunlight have been held constant, the removal of far-red alone alters plant growth. As shown for chrysanthemum, with FR depletion plants grown in sunlight are small, more branched and darker green. We examine the implications for plant growth and flowering when the far-red composition of incident radiation in plant growth chambers is manipulated.

  17. Taylor Hydro plant goes live

    International Nuclear Information System (INIS)

    Anon.

    2000-01-01

    The 12.75 MW Taylor Hydroelectric Plant in Magrath, Alberta, synchronized its generator with the Alberta Power Grid and began production in April 2000. The plant is located on Government of Alberta irrigation works and is owned by Canadian Hydro Developers. During the irrigation season the plant will generate approximately 40 million kilowatt hours of zero-emission 'green' power for consumption, enough to power 5,000 homes for a year. The Taylor plant is a joint venture with EPCOR Power Development Corporation, a wholly-owned subsidiary of EPCOR Inc., the City of Edmonton utility. Canadian Hydro Developers also owns a 19 MW wind plant and a 6 MW gas plant in Alberta and five other 'run of river' hydro plants in Ontario and British Columbia. The company is committed to the concept of low-impact power generation; its ownership of wind run-of-river hydro and gas-fired facilities is proof of that commitment

  18. Effects of fluorides on plants

    Energy Technology Data Exchange (ETDEWEB)

    Yamazoe, F

    1975-11-01

    Fluorine compounds known to be air pollutants, such as hydrogen fluoride and silicon tetrachloride, are highly poisonous to plants even at ppm - ppb levels. As solid microparticles, acidic sodium fluoride and cryolite cause problems by adhering to plant leaves and absorbing into plant bodies. Plants are classified by their susceptibility to hydrogen fluoride: gladiolus, apricot, buckwheat, turnip and Vaccinium vitis-idaea are most susceptible showing slight injury at less than 5 ppb for 7-9 days; maize, pepper, and dahlia are fairly susceptible, followed by azalea, rose, lilac, and alfalfa, then by oak and tomato. Gladiolus is used as an indicator plant. The exposure factor for one species was known. The symptoms of plants exposed to gaseous fluorine compounds are described in detail at various concentrations. The causal mechanism of the injuries due to fluorine compounds is described in detail, with the method of determining the fluorine content of plant parts. 7 references.

  19. Industrial safety in power plants

    International Nuclear Information System (INIS)

    1987-01-01

    The proceedings of the VGB conference 'Industrial safety in power plants' held in the Gruga-Halle, Essen on January 21 and 22, 1987, contain the papers reporting on: Management responsibility for and legal consequences of industrial safety; VBG 2.0 Industrial Accident Prevention Regulation and the power plant operator; Operational experience gained with wet-type flue gas desulphurization systems; Flue gas desulphurization systems: Industrial-safety-related requirements to be met in planning and operation; the effects of the Hazardous Substances Ordinance on power plant operation; Occupational health aspects of heat-exposed jobs in power plants; Regulations of the Industrial Accident Insurance Associations concerning heat-exposed jobs and industrial medical practice; The new VBG 30 Accident Prevention Regulation 'Nuclear power plants'; Industrial safety in nuclear power plants; safe working on and within containers and confined spaces; Application of respiratory protection equipment in power plants. (HAG) [de

  20. Pinellas Plant Environmental Baseline Report

    Energy Technology Data Exchange (ETDEWEB)

    1997-06-01

    The Pinellas Plant has been part of the Department of Energy`s (DOE) nuclear weapons complex since the plant opened in 1957. In March 1995, the DOE sold the Pinellas Plant to the Pinellas County Industry Council (PCIC). DOE has leased back a large portion of the plant site to facilitate transition to alternate use and safe shutdown. The current mission is to achieve a safe transition of the facility from defense production and prepare the site for alternative uses as a community resource for economic development. Toward that effort, the Pinellas Plant Environmental Baseline Report (EBR) discusses the current and past environmental conditions of the plant site. Information for the EBR is obtained from plant records. Historical process and chemical usage information for each area is reviewed during area characterizations.