Soil–structure interaction analyses to locate nuclear power plant free-field seismic instrumentation

Energy Technology Data Exchange (ETDEWEB)

Johnson, James J., E-mail: jasjjoh@aol.com [James J. Johnson and Associates, Alamo, CA (United States); Ake, Jon P. [US Nuclear Regulatory Commission, Washington, DC (United States); Maslenikov, Oleg R. [James J. Johnson and Associates, Alamo, CA (United States); Kenneally, Roger M. [Consultant, Seminole, FL (United States)

2015-12-15

Highlights: • Determine the location of seismic instrumentation so that recorded motion will be free-field motion. • Certified Designs of nuclear island for AP1000 and EPR; ABWR Reactor Building were analyzed. • Three site conditions and multiple recorded time histories were considered. • Instrumentation located 1-diameter from the edge of structure/foundation is adequate. • Acceptance criteria were probability of non-exceedance of response spectra values. - Abstract: The recorded earthquake ground motion at the nuclear power plant site is needed for several purposes. US Nuclear Regulatory Commission (NRC) Regulatory Guide 1.12, Nuclear Power Plant Instrumentation for Earthquakes, NRC (1997a), describes acceptable instrumentation to meet the requirements in NRC's regulations pertaining to earthquake engineering criteria for nuclear power plants. The ground motion data recorded by the free-field seismic instrumentation are used to compare the actual earthquake motion at the site with the design input motion. The result of the comparison determines if the Operating Basis Earthquake ground motion (OBE) has been exceeded and plant shutdown is required per the guidance in NRC Regulatory Guide 1.166, Pre-Earthquake Planning and Immediate Nuclear Power Plant Operator Postearthquake Actions, NRC (1979b). The free-field is defined as a location on the ground surface or in the site soil column that is sufficiently distant from the site structures to be essentially unaffected by the vibration of the site structures.

Selection of a plant location - A case study: Urea production using ...

African Journals Online (AJOL)

Selection of a plant location - A case study: Urea production using Calub Gas. ... The criteria are. amongst others, supply of raw materials and fuel, market proximity, water supply. waste ... To set up · critical factors for Ethiopian scenario

Parasitic plants in agriculture: Chemical ecology of germination and host-plant location as targets for sustainable control: A review

Science.gov (United States)

Justin B. Runyon; John F. Tooker; Mark C. Mescher; Consuelo M. De Moraes

2009-01-01

Parasitic plants are among the most problematic pests of agricultural crops worldwide. Effective means of control are generally lacking, in part because of the close physiological connection between the established parasite and host plant hindering efficient control using traditional methods. Seed germination and host location are critical early-growth stages that...

In vivo synthesis of nanomaterials in plants: location of silver nanoparticles and plant metabolism

Science.gov (United States)

Marchiol, Luca; Mattiello, Alessandro; Pošćić, Filip; Giordano, Cristiana; Musetti, Rita

2014-03-01

Metallic nanoparticles (MeNPs) can be formed in living plants by reduction of the metal ions absorbed as soluble salts. It is very likely that plant metabolism has an important role in MeNP biosynthesis. The in vivo formation of silver nanoparticles (AgNPs) was observed in Brassica juncea, Festuca rubra and Medicago sativa. Plants were grown in Hoagland's solution for 30 days and then exposed for 24 h to a solution of 1,000 ppm AgNO3. In the leaf extracts of control plants, the concentrations of glucose, fructose, ascorbic acid, citric acid and total polyphenols were determined. Total Ag content in plant fractions was determined by inductively coupled plasma atomic emission spectroscopy. Despite the short exposure time, the Ag uptake and translocation to plant leaves was very high, reaching 6,156 and 2,459 mg kg-1 in B. juncea and F. rubra, respectively. Ultrastructural analysis was performed by transmission electron microscopy (TEM), and AgNPs were detected by TEM X-ray microanalysis. TEM images of plant fractions showed the in vivo formation of AgNPs in the roots, stems and leaves of the plants. In the roots, AgNPs were present in the cortical parenchymal cells, on the cell wall of the xylem vessels and in regions corresponding to the pits. In leaf tissues, AgNPs of different sizes and shapes were located close to the cell wall, as well as in the cytoplasm and within chloroplasts. AgNPs were not observed in the phloem of the three plant species. This is the first report of AgNP synthesis in living plants of F. rubra. The contents of reducing sugars and antioxidant compounds, proposed as being involved in the biosynthesis of AgNPs, were quite different between the species, thus suggesting that it is unlikely that a single substance is responsible for this process.

Logistic regression models of factors influencing the location of bioenergy and biofuels plants

Science.gov (United States)

T.M. Young; R.L. Zaretzki; J.H. Perdue; F.M. Guess; X. Liu

2011-01-01

Logistic regression models were developed to identify significant factors that influence the location of existing wood-using bioenergy/biofuels plants and traditional wood-using facilities. Logistic models provided quantitative insight for variables influencing the location of woody biomass-using facilities. Availability of "thinnings to a basal area of 31.7m2/ha...

pLoc-mPlant: predict subcellular localization of multi-location plant proteins by incorporating the optimal GO information into general PseAAC.

Science.gov (United States)

Cheng, Xiang; Xiao, Xuan; Chou, Kuo-Chen

2017-08-22

One of the fundamental goals in cellular biochemistry is to identify the functions of proteins in the context of compartments that organize them in the cellular environment. To realize this, it is indispensable to develop an automated method for fast and accurate identification of the subcellular locations of uncharacterized proteins. The current study is focused on plant protein subcellular location prediction based on the sequence information alone. Although considerable efforts have been made in this regard, the problem is far from being solved yet. Most of the existing methods can be used to deal with single-location proteins only. Actually, proteins with multi-locations may have some special biological functions. This kind of multiplex protein is particularly important for both basic research and drug design. Using the multi-label theory, we present a new predictor called "pLoc-mPlant" by extracting the optimal GO (Gene Ontology) information into the Chou's general PseAAC (Pseudo Amino Acid Composition). Rigorous cross-validation on the same stringent benchmark dataset indicated that the proposed pLoc-mPlant predictor is remarkably superior to iLoc-Plant, the state-of-the-art method for predicting plant protein subcellular localization. To maximize the convenience of most experimental scientists, a user-friendly web-server for the new predictor has been established at , by which users can easily get their desired results without the need to go through the complicated mathematics involved.

GIS-BASED location optimization of a biomass conversion plant on contaminated willow in the Campine region (Belgium)

International Nuclear Information System (INIS)

Voets, Thomas; Neven, An; Thewys, Theo; Kuppens, Tom

2013-01-01

The Campine region is diffusely contaminated with heavy metals like cadmium. Since traditional excavation techniques are too expensive, phytoremediation is preferred as a remediation technique. In a previous study, the biomass potential from phytoremediation of contaminated agricultural land in the Campine region in Belgium was assessed. Based on recently upgraded figures of willow potential from phytoremediation on agricultural land in the seven most contaminated municipalities of the Belgian Campine region, the current paper uses GIS-knowledge to investigate which of three previously identified locations is most suitable for a biomass plant, taking into account the spatial distribution of the contaminated willow supply and the total cost of willow transport. Biomass transport distance from the centroid of each contaminated agricultural parcel to each of the three potential biomass plant locations was determined following Euclidian distance calculations and distance calculations over the existing road network. A transport cost model consisting of distance fixed and distance dependent biomass transport costs was developed. Of the locations identified, the Overpelt Fabriek site results in the lowest biomass transport distance and costs. When willow allocation for each parcel occurs based on the nearest potential plant location, transport costs are on average 23% lower than when all biomass is transported to the single Overpelt Fabriek site location. Therefore, when only considering transport costs, installing a smaller plant at each of the three potential plant locations would be less expensive than when installing a single biomass plant at the Overpelt Fabriek site. -- Highlights: ► Overpelt Fabriek site most attractive for time frames considered. ► Average tortuosity factor in Campine region between 1.27 and 1.42. ► Share of willow transport costs in willow supply costs 21%. ► Optimal allocation of willow results in lower transport costs

RESERCH STUDIES ON THE LOCATION OF A WAVE ENERGY POWER PLANT WITHIN CONSTANTA AREA

Directory of Open Access Journals (Sweden)

SAMOILESCU Gheorghe

2015-05-01

Full Text Available This paper is based on a research project on the development and installation of the first hydropneumatic plant in the Black Sea. It shows the location and its particularities, existing and previous hydrometeorological conditions, required work, plant qualities and standards to be met. The wave characteristics calculation and the hydrotechnic studies were presented: articulated concrete blocks demolition of the existing breakwater; dredging for the foundation of the plant; accomplish the foundation of the plant; installation of the plant; testing; consolidation and assuring protection of the breakwater; consolidation and assuring protection of the plant. Environmental protection measures are an important part of any research project of this type.

Substantiation of the radiation monitoring scope in the region of nuclear power plant location

Energy Technology Data Exchange (ETDEWEB)

Zykova, A S; Zhakov, Yu A; Yambrovskii, Ya M

1977-12-01

To provide radiation safety of the population in the region of nuclear power plant location, it is necessary to define the character and quantity of radiation monitoring. On the basis of radiation monitoring of effluents from operating nuclear power plants it is found that the effluents can be registered at a distance of 5-7 km from the plant. The quantity of sample analysis of the main enviromental objectives must provide an exact definition of the content of radioactive substances produced by radioactive fallouts and effluents from nuclear power plants.

Substantiation of the radiation monitoring scope in the region of nuclear power plant location

International Nuclear Information System (INIS)

Zykova, A.S.; Zhakov, Yu.A.; Jambrovskij, Ya.M.

1977-01-01

To provide radiation safety of the population in the region of nuclear power plant location, it is necessary to define the character and quantity of radiation monitoring. On the basis of radiation monitoring of flowouts from operating nuclear power plants it is found that the flowouts can be registered at a distance of 5-7 km from the plant. The quantity of sample analysis of the main enviromental objectives must provide an exact definition of the content of radioactive substances produced by radioactive fallouts and flowouts from nuclear power plants

Influences of Plant Species, Season and Location on Leaf Endophytic Bacterial Communities of Non-Cultivated Plants.

Science.gov (United States)

Ding, Tao; Melcher, Ulrich

2016-01-01

Bacteria are known to be associated endophytically with plants. Research on endophytic bacteria has identified their importance in food safety, agricultural production and phytoremediation. However, the diversity of endophytic bacterial communities and the forces that shape their compositions in non-cultivated plants are largely uncharacterized. In this study, we explored the diversity, community structure, and dynamics of endophytic bacteria in different plant species in the Tallgrass Prairie Preserve of northern Oklahoma, USA. High throughput sequencing of amplified segments of bacterial rDNA from 81 samples collected at four sampling times from five plant species at four locations identified 335 distinct OTUs at 97% sequence similarity, representing 16 phyla. Proteobacteria was the dominant phylum in the communities, followed by the phyla Bacteriodetes and Actinobacteria. Bacteria from four classes of Proteobacteria were detected with Alphaproteobacteria as the dominant class. Analysis of molecular variance revealed that host plant species and collecting date had significant influences on the compositions of the leaf endophytic bacterial communities. The proportion of Alphaproteobacteria was much higher in the communities from Asclepias viridis than from other plant species and differed from month to month. The most dominant bacterial groups identified in LDA Effect Size analysis showed host-specific patterns, indicating mutual selection between host plants and endophytic bacteria and that leaf endophytic bacterial compositions were dynamic, varying with the host plant's growing season in three distinct patterns. In summary, next generation sequencing has revealed variations in the taxonomic compositions of leaf endophytic bacterial communities dependent primarily on the nature of the plant host species.

Influences of Plant Species, Season and Location on Leaf Endophytic Bacterial Communities of Non-Cultivated Plants.

Directory of Open Access Journals (Sweden)

Tao Ding

Full Text Available Bacteria are known to be associated endophytically with plants. Research on endophytic bacteria has identified their importance in food safety, agricultural production and phytoremediation. However, the diversity of endophytic bacterial communities and the forces that shape their compositions in non-cultivated plants are largely uncharacterized. In this study, we explored the diversity, community structure, and dynamics of endophytic bacteria in different plant species in the Tallgrass Prairie Preserve of northern Oklahoma, USA. High throughput sequencing of amplified segments of bacterial rDNA from 81 samples collected at four sampling times from five plant species at four locations identified 335 distinct OTUs at 97% sequence similarity, representing 16 phyla. Proteobacteria was the dominant phylum in the communities, followed by the phyla Bacteriodetes and Actinobacteria. Bacteria from four classes of Proteobacteria were detected with Alphaproteobacteria as the dominant class. Analysis of molecular variance revealed that host plant species and collecting date had significant influences on the compositions of the leaf endophytic bacterial communities. The proportion of Alphaproteobacteria was much higher in the communities from Asclepias viridis than from other plant species and differed from month to month. The most dominant bacterial groups identified in LDA Effect Size analysis showed host-specific patterns, indicating mutual selection between host plants and endophytic bacteria and that leaf endophytic bacterial compositions were dynamic, varying with the host plant's growing season in three distinct patterns. In summary, next generation sequencing has revealed variations in the taxonomic compositions of leaf endophytic bacterial communities dependent primarily on the nature of the plant host species.

Formation and Change of Chloroplast-Located Plant Metabolites in Response to Light Conditions

Directory of Open Access Journals (Sweden)

Yiyong Chen

2018-02-01

Full Text Available Photosynthesis is the central energy conversion process for plant metabolism and occurs within mature chloroplasts. Chloroplasts are also the site of various metabolic reactions involving amino acids, lipids, starch, and sulfur, as well as where the production of some hormones takes place. Light is one of the most important environmental factors, acting as an essential energy source for plants, but also as an external signal influencing their growth and development. Plants experience large fluctuations in the intensity and spectral quality of light, and many attempts have been made to improve or modify plant metabolites by treating them with different light qualities (artificial lighting or intensities. In this review, we discuss how changes in light intensity and wavelength affect the formation of chloroplast-located metabolites in plants.

Study of Real Time Location System For Worker in Containment Building at Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Lee, S. Y.; Kim, G. S. [Samchang Enterprise Company, Ulsan (Korea, Republic of); Kim, H. S. [Ulsan Univ., Ulsan (Korea, Republic of)

2012-03-15

Workers are required special management to minimize radiation exposure in nuclear power plant. Especially, there are many limitation in their activities at containment building in nuclear power plant. Test personnel shall administer the workers by tracing the location of them inside containment building in nuclear power plant. They may be exposed to the unnecessary radiation due to a complex and high radiation area in the building. Test personnel needs to manage efficiently for worker's safety and work hours at containment building. Therefore, it is critical for the test personnel to notice the risk to the workers by identifying the location when the workers are facing the dangerous situation on the high area. In this paper, we introduce requirements and design method to develop the one and two dimensional RTLS(Real Time Locating System) by using CSS(Chirp Spread Spectrum) which enables precise location measurement and robust data communication even indoor environment with serious electromagnetic interference caused by complicated structure such as the inside of containment building in the nuclear power plant. In the algorithm to compute the distance, it is suggested to use SDS-TWR(Symmetrical Double-Sided Two-Way Ranging) to solve the issue of indirect routes, and develop the power circuit with 10mW of designing gain for output power to meet the KCC standard in order to increase the raging distance, in addition, communication between Anchor and distance measuring computer shall be designed to increase energy using time of Tags(nodes) by using CAN(Controller Area Network) communication.

Economic optimisation of a wind power plant for isolated locations

International Nuclear Information System (INIS)

Fortunato, B.; Mummolo, G.; Cavallera, G.

1997-01-01

This paper presents a model of a wind power plant for isolated locations composed of a vertical axis wind turbine connected to a self-excited induction generator operating at constant voltage and frequency; a back-up diesel generator and a battery system are moreover included in the system. Constant voltage and frequency are obtained only by controlling the generator appropriately. The control system is supposed to be optimised so that the system operates at the highest efficiency. In order to improve the total efficiency even further, a gear-box to vary the gear transmission ratio between the turbine and the generator has been considered. A ''Monte Carlo'' type simulation has been used to analyse the operation of that system over a one year period. The model is based on a probability density function of the wind speed derived by statistical data concerning a given location and on the probabilistic curve of the load required by an isolated location. The cost per kW h for different dimensions of the main components has been evaluated and the optimum configuration has been identified. (author)

A method for locating potential tree-planting sites in urban areas: a case study of Los Angeles, USA

Science.gov (United States)

Chunxia Wua; Qingfu Xiaoa; Gregory E. McPherson

2008-01-01

A GIS-based method for locating potential tree-planting sites based on land cover data is introduced. Criteria were developed to identify locations that are spatially available for potential tree planting based on land cover, sufficient distance from impervious surfaces, a minimum amount of pervious surface, and no crown overlap with other trees. In an ArcGIS...

Social assessment and location of nuclear and thermal power plants

International Nuclear Information System (INIS)

Nemoto, Kazuyasu; Nishio, Mitsuo.

1979-01-01

Most of the locations of nuclear and thermal power plants in Japan are depopulated villages with remote rural character, but for the development of such districts, the policy is not yet clearly established, and the appropriate measures are not taken. The living regions of residents and the production regions of enterprises are more and more estranged. Social assessment is the scientific method to perceive the future change due to the installation of power stations. The features particular to the assessment of natural environment and social environment related to the location of power stations are considered, and the technical problems involved in the method of assessment of natural environment are solved, and the actual method of assessment of social environment is developed. Then, the possibility of establishing this method and the problems in its application are investigated. The plan of developing the surroundings of power generation facilities is criticized, and the coordination of the location plan of power companies and the regional projects of municipalities is discussed. Finally, the mechanism of consensus formation concerning the location of power stations is considered, dividing into regional consensus formation and administrative consensus formation, and the possibility of instituting social assessment is examined. (Kako, I.)

Siting locally-unwanted facilities: What can be learnt from the location of Italian power plants

International Nuclear Information System (INIS)

Garrone, Paola; Groppi, Angelamaria

2012-01-01

The reaction of communities to the development of energy facilities is based on the environmental impact of the investment, but it also reflects the ex-ante propensity of residents to engage in collective actions. In this work we have examined the requests of authorization of Italian power producers for new thermal plants with the purpose of testing the efficiency of market-based siting policies. The classical location factors, e.g., infrastructure availability, have been confirmed to play a role, and there is a weak evidence that authorization demands have targeted communities that suffer less environmental damage. However our findings have also revealed that power producers are likely to avoid potentially suitable sites if they host a highly activistic community. The paper also discusses some modifications concerning siting policies that could improve the alignment between community responses and the environmental costs of new energy facilities. - Highlights: ► We model location choices for polluting power plants by Italian producers in 1999–2006. ► The efficiency of market-based siting policies is tested (i.e., plants located where environmental damage is lower). ► More than environmental costs, voice factors prevailed on the location choices. ► We conclude that market-based siting policies does not ensure an efficient outcome. ► Developers and communities relationship may suffer from relevant transaction costs

An approach to evaluating alternatives for wind power plant locations

Directory of Open Access Journals (Sweden)

Rehman, Ateekh Ur

2016-12-01

Full Text Available Multi-criteria decision approaches are preferred for achieving multi-dimensional sustainable renewable energy goals. A more critical issue faced by the wind power industry is the selection of a location to tap prospective energy, which needs to be evaluated on multiple measures. In this paper, the aim is to assess and rank alternative wind power plant locations in Saudi Arabia. The approach presented here takes multiple criteria into consideration, such as wind speed, wind availability, site advantages, terrain details, risk and uncertainty, technology used, third party support, projected demand, types of customers, and government policies. A comparative analysis of feasible alternatives that satisfy all multi- criteria objectives is carried out. The results obtained are subjected to sensitivity analysis. Concepts such as ‘threshold values’ and ‘attribute weights’ make the approach more sensitive.

Feasibility Study for Co-Locating and Integrating Ethanol Production Plants from Corn Starch and Lignocellulosic Feedstocks (Revised)

Energy Technology Data Exchange (ETDEWEB)

Wallace, R.; Ibsen, K.; McAloon, A.; Yee, W.

2005-01-01

Analysis of the feasibility of co-locating corn-grain-to-ethanol and lignocellulosic ethanol plants and potential savings from combining utilities, ethanol purification, product processing, and fermentation. Although none of the scenarios identified could produce ethanol at lower cost than a straight grain ethanol plant, several were lower cost than a straight cellulosic ethanol plant.

7 CFR 1032.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1032.75 Section 1032.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1124.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1124.75 Section 1124.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1005.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1005.75 Section 1005.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1007.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1007.75 Section 1007.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1033.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1033.75 Section 1033.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1030.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1030.75 Section 1030.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1001.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1001.75 Section 1001.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1126.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1126.75 Section 1126.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

7 CFR 1006.75 - Plant location adjustments for producer milk and nonpool milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Plant location adjustments for producer milk and nonpool milk. 1006.75 Section 1006.75 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Milk), DEPARTMENT OF AGRICULTURE MILK IN THE...

Mapping topographic plant location properties using a dense matching approach

Science.gov (United States)

Niederheiser, Robert; Rutzinger, Martin; Lamprecht, Andrea; Bardy-Durchhalter, Manfred; Pauli, Harald; Winkler, Manuela

2017-04-01

Within the project MEDIALPS (Disentangling anthropogenic drivers of climate change impacts on alpine plant species: Alps vs. Mediterranean mountains) six regions in Alpine and in Mediterranean mountain regions are investigated to assess how plant species respond to climate change. The project is embedded in the Global Observation Research Initiative in Alpine Environments (GLORIA), which is a well-established global monitoring initiative for systematic observation of changes in the plant species composition and soil temperature on mountain summits worldwide to discern accelerating climate change pressures on these fragile alpine ecosystems. Close-range sensing techniques such as terrestrial photogrammetry are well suited for mapping terrain topography of small areas with high resolution. Lightweight equipment, flexible positioning for image acquisition in the field, and independence on weather conditions (i.e. wind) make this a feasible method for in-situ data collection. New developments of dense matching approaches allow high quality 3D terrain mapping with less requirements for field set-up. However, challenges occur in post-processing and required data storage if many sites have to be mapped. Within MEDIALPS dense matching is used for mapping high resolution topography for 284 3x3 meter plots deriving information on vegetation coverage, roughness, slope, aspect and modelled solar radiation. This information helps identifying types of topography-dependent ecological growing conditions and evaluating the potential for existing refugial locations for specific plant species under climate change. This research is conducted within the project MEDIALPS - Disentangling anthropogenic drivers of climate change impacts on alpine plant species: Alps vs. Mediterranean mountains funded by the Earth System Sciences Programme of the Austrian Academy of Sciences.

Rhizosphere microbial community structure in relation to root location and plant iron nutritional status.

Science.gov (United States)

Yang, C H; Crowley, D E

2000-01-01

Root exudate composition and quantity vary in relation to plant nutritional status, but the impact of the differences on rhizosphere microbial communities is not known. To examine this question, we performed an experiment with barley (Hordeum vulgare) plants under iron-limiting and iron-sufficient growth conditions. Plants were grown in an iron-limiting soil in root box microcosms. One-half of the plants were treated with foliar iron every day to inhibit phytosiderophore production and to alter root exudate composition. After 30 days, the bacterial communities associated with different root zones, including the primary root tips, nonelongating secondary root tips, sites of lateral root emergence, and older roots distal from the tip, were characterized by using 16S ribosomal DNA (rDNA) fingerprints generated by PCR-denaturing gradient gel electrophoresis (DGGE). Our results showed that the microbial communities associated with the different root locations produced many common 16S rDNA bands but that the communities could be distinguished by using correspondence analysis. Approximately 40% of the variation between communities could be attributed to plant iron nutritional status. A sequence analysis of clones generated from a single 16S rDNA band obtained at all of the root locations revealed that there were taxonomically different species in the same band, suggesting that the resolving power of DGGE for characterization of community structure at the species level is limited. Our results suggest that the bacterial communities in the rhizosphere are substantially different in different root zones and that a rhizosphere community may be altered by changes in root exudate composition caused by changes in plant iron nutritional status.

Determination of Effective Criteria for Location Selection of Kiln Wood Drying Plants by AHP Technique

Directory of Open Access Journals (Sweden)

Rahim Mohebbi

2011-12-01

Full Text Available This study was aimed at determining the effective criteria for location selection of wood drying plants in Iran. For this purpose, after review and field visit of the industries, 35 key indicators were identified. These criteria were divided into five major groups as: materials, infrastructure, technical, economical and instructional indices. The priority rates of these criteria and sub-criteria were evaluated by AHP technique. The results indicated that among 35 effective sub-criteria in location selection of the plants, the sub-criteria of quality of raw materials(0.152, purchasing raw materials, land cost, profitability, reliability of supply, and sales had the highest priorities, which were rated as 0.118, 0.105, 0.067, 0.061 and 0.057, respectively

TRACE ELEMENT CONTENTS IN TOPSOIL LOCATED NEAR STEEL PLANT IN KRAKOW-NOWA HUTA

Directory of Open Access Journals (Sweden)

Paweł Mundała

2014-10-01

Full Text Available The paper presents the results of cadmium, lead and zinc contents in topsoils of arable land located in vicinity Steel Plant in Krakow-Nowa Huta. Soil samples were collected in autumn 2007 from the 0-20 cm layer placed in a west-east trnsect of 7,5 km length. It started approximately 5km east form the border of the steel plant. .Sampled area is characterized by high level of agriculture, where the dominant crops have been vegetables, mainly cabbage and cauliflower. It was found, the soil was not contaminated with heavy metals. All samples met the requirements of the Polish Minister of the Environment. Also the assessment according to Institute of Soil Science and Plant Cultivation method showed only incerased content 60% in case of zinc and only 13% for Cd. Any levels of pollution were not observed. There also decreasing trend of accumulation were stated as a function of growing distance from the steel plant.

A Hybrid Multidimensional Approach to Select a Country for Global Cement Plant Location

Directory of Open Access Journals (Sweden)

Muhammad Khurram Ali

2015-04-01

Full Text Available The globalization and saturated domestic markets force international firms to gradually expand their businesses across the borders to capture potential emerging markets. The decision to select a country for a new cement plant location demands analysis of a large number of factors. It is a multifaceted problem which requires investigation and prioritization of factors in a hierarchical way.This paper uses an FAHP (Fuzzy Analytic Hierarchy Process based procedure proposing a practical framework for solution of the GCPLP (Global Cement Plant Location Problem. It deals with real world ambiguities and handles a broader spectrum of influencing factors. The criteria for selection of a country for a new cement plant installation are prioritized from the FAHP based evaluation made by experts. Different global databases including the World Bank are used for the fuzzy ratings of the alternatives. It has been learnt in this particular problem that cement specific and cost related factors are the most sensitive while legal regulations and economic conditions are relatively less sensitive for the decision makers. Therefore, the countries having strong lime stone reserves, cheaper fuel costs and good internal marketing positions are higher in ranking. The paper concludes with different rankings of the four countries analyzed which assist the strategic managers in making decisions on the basis of mathematically computed results.

A hybrid multidimensional approach to select a country for global cement plant location

International Nuclear Information System (INIS)

Ali, M.K.

2015-01-01

The globalization and saturated domestic markets force international firms to gradually expand their businesses across the borders to capture potential emerging markets. The decision to select a country for a new cement plant location demands analysis of a large number of factors. It is a multifaceted problem which requires investigation and prioritization of factors in a hierarchical way. This paper uses an FAHP (Fuzzy Analytic Hierarchy Process) based procedure proposing a practical framework for solution of the GCPLP (Global Cement Plant Location Problem). It deals with real world ambiguities and handles a broader spectrum of influencing factors. The criteria for selection of a country for a new cement plant installation are prioritized from the FAHP based evaluation made by experts. Different global databases including the World Bank are used for the fuzzy ratings of the alternatives. It has been learnt in this particular problem that cement specific and cost related factors are the most sensitive while legal regulations and economic conditions are relatively less sensitive for the decision makers. Therefore, the countries having strong lime stone reserves, cheaper fuel costs and good internal marketing positions are higher in ranking. The paper concludes with different rankings of the four countries analyzed which assist the strategic managers in making decisions on the basis of mathematically computed results. (author)

Design and Analysis of Photovoltaic (PV) Power Plant at Different Locations in Malaysia

Science.gov (United States)

Islam, M. A.; Hasanuzzaman, M.; Rahim, N. A.

2018-05-01

Power generation from sun oriented vitality through a photovoltaic (PV) system is ended up prevalent over the world due to clean innovation. Geographical location of Malaysia is very favorable for PV power generation system. The Malaysian government has also taken different steps to increase the use of solar energy especially by emphasizing on building integrated PV (BIPV) system. Comparative study on the feasibility of BIPV installation at the different location of Malaysia is rarely found. On the other hand, solar cell temperature has a negative impact on the electricity generation. So in this study cost effectiveness and initial investment cost of building integrated grid connected solar PV power plant in different regions of Malaysia have been carried. The effect of PV solar cell temperature on the payback period (PBP) is also investigated. Highest PBP is 12.38 years at Selangor and lowest PBP is 9.70 years at Sabah (Kota Kinabalu). Solar cell temperature significantly increases the PBP of PV plant and highest 14.64% and lowest 13.20% raise of PBP are encountered at Penang and Sarawak respectively.

30 CFR 947.827 - Special performance standards-coal processing plants and support facilities not located at or...

Science.gov (United States)

2010-07-01

... mining and reclamation operations which include the operation of coal processing plants and support... plants and support facilities not located at or near the minesite or not within the permit area for a mine. 947.827 Section 947.827 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...

30 CFR 912.827 - Special performance standards-coal processing plants and support facilities not located at or...

Science.gov (United States)

2010-07-01

... mining and reclamation operations which includes the operation of coal processing plants and support... plants and support facilities not located at or near the minesite or not within the permit area for a mine. 912.827 Section 912.827 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...

30 CFR 922.827 - Special performance standards-coal processing plants and support facilities not located at or...

Science.gov (United States)

2010-07-01

... mining and reclamation operations which include the operation of coal processing plants and support... plants and support facilities not located at or near the minesite or not within the permit area for a mine. 922.827 Section 922.827 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...

30 CFR 937.827 - Special performance standards-coal processing plants and support facilities not located at or...

Science.gov (United States)

2010-07-01

... mining and reclamation operations which include the operation of coal processing plants and support... plants and support facilities not located at or near the minesite or not within the permit area for a mine. 937.827 Section 937.827 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...

30 CFR 910.827 - Special performance standards-coal processing plants and support facilities not located at or...

Science.gov (United States)

2010-07-01

... mining and reclamation operations which includes the operation of coal processing plants and support... plants and support facilities not located at or near the minesite or not within the permit area for a mine. 910.827 Section 910.827 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT...

Feasibility study for co-locating and integrating ethanol production plants from corn starch and lignocellulosic feedstocks

Energy Technology Data Exchange (ETDEWEB)

Wallace, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ibsen, Kelly [National Renewable Energy Lab. (NREL), Golden, CO (United States); McAloon, Andrew [U.S. Department of Agriculture, Washington, D.C. (United States); Yee, Winnie [U.S. Department of Agriculture, Washington, D.C. (United States)

2005-01-01

Analysis of the feasibility of co-locating corn-grain-to-ethanol and lignocellulosic ethanol plants and potential savings from combining utilities, ethanol purification, product processing, and fermentation.

Life Cycle Assessment of a HYSOL Concentrated Solar Power Plant: Analyzing the Effect of Geographic Location

Directory of Open Access Journals (Sweden)

Blanca Corona

2016-05-01

Full Text Available Concentrating Solar Power (CSP technology is developing in order to achieve higher energy efficiency, reduced economic costs, and improved firmness and dispatchability in the generation of power on demand. To this purpose, a research project titled HYSOL has developed a new power plant, consisting of a combined cycle configuration with a 100 MWe steam turbine and an 80 MWe gas-fed turbine with biomethane. Technological developments must be supported by the identification, quantification, and evaluation of the environmental impacts produced. The aim of this paper is to evaluate the environmental performance of a CSP plant based on HYSOL technology using a Life Cycle Assessment (LCA methodology while considering different locations. The scenarios investigated include different geographic locations (Spain, Chile, Kingdom of Saudi Arabia, Mexico, and South Africa, an alternative modelling procedure for biomethane, and the use of natural gas as an alternative fuel. Results indicate that the geographic location has a significant influence on the environmental profile of the HYSOL CSP plant. The results obtained for the HYSOL configuration located in different countries presented significant differences (between 35% and 43%, depending on the category, especially in climate change and water stress categories. The differences are mainly attributable to the local availability of solar and water resources and composition of the national electricity mix. In addition, HYSOL technology performs significantly better when hybridizing with biomethane instead of natural gas. This evidence is particularly relevant in the climate change category, where biomethane hybridization emits 27.9–45.9 kg CO2 eq per MWh (depending on the biomethane modelling scenario and natural gas scenario emits 264 kg CO2 eq/MWh.

The influence of geographic location on population exposure to emissions from power plants throughout China

International Nuclear Information System (INIS)

Ying Zhou; Levy, J.I.; Evans, J.S.; Hammitt, J.K.

2006-01-01

This analysis seeks to evaluate the influence of emission source location on population exposure in China to fine particles and sulfur dioxide. We use the concept of intake fraction, defined as the fraction of material or its precursor released from a source that is eventually inhaled or ingested by a population. We select 29 power-plant sites throughout China and estimate annual average intake fractions at each site, using identical source characteristics to isolate the influence of geographic location. In addition, we develop regression models to interpret the intake fraction values and allow for extrapolation to other sites. To model the concentration increase due to emissions from selected power plants, we used a detailed long-range atmospheric dispersion model, CALPUFF. Primary fine particles have the highest average intake fraction (1 x 10 -5 ), followed by sulfur dioxide (5 x 10 -6 ), sulfate from sulfur dioxide (4 x 10 -6 ), and nitrate from nitrogen oxides (4 x 10 -6 ). For all pollutants, the intake fractions span approximately an order of magnitude across sites. In the regression analysis, the independent variables are meteorological proxies (such as climate region and precipitation) and population at various distances from the source. We find that population terms can explain a substantial percentage of variability in the intake fraction for all pollutants (R 2 between 0.86 and 0.95 across pollutants), with a significant modifying influence of meteorological regime. Near-source population is more important for primary coarse particles while population at medium to long distance is more important for primary fine particles and secondary particles. A significant portion of intake fraction (especially for secondary particles and primary fine particles) occurs beyond 500 km of the source, emphasizing the need for detailed long-range dispersion modeling. These findings demonstrate that intake fractions for power plants in China can be estimated with

The influence of geographic location on population exposure to emissions from power plants throughout China

Energy Technology Data Exchange (ETDEWEB)

Ying Zhou; Levy, J.I. [Harvard School of Public Health, Boston, MA (United States); Evans, J.S.; Hammitt, J.K. [Harvard Center for Risk Analysis, Boston, MA (United States)

2006-04-15

This analysis seeks to evaluate the influence of emission source location on population exposure in China to fine particles and sulfur dioxide. We use the concept of intake fraction, defined as the fraction of material or its precursor released from a source that is eventually inhaled or ingested by a population. We select 29 power-plant sites throughout China and estimate annual average intake fractions at each site, using identical source characteristics to isolate the influence of geographic location. In addition, we develop regression models to interpret the intake fraction values and allow for extrapolation to other sites. To model the concentration increase due to emissions from selected power plants, we used a detailed long-range atmospheric dispersion model, CALPUFF. Primary fine particles have the highest average intake fraction (1 x 10{sup -5}), followed by sulfur dioxide (5 x 10{sup -6}), sulfate from sulfur dioxide (4 x 10{sup -6}), and nitrate from nitrogen oxides (4 x 10{sup -6}). For all pollutants, the intake fractions span approximately an order of magnitude across sites. In the regression analysis, the independent variables are meteorological proxies (such as climate region and precipitation) and population at various distances from the source. We find that population terms can explain a substantial percentage of variability in the intake fraction for all pollutants (R{sup 2} between 0.86 and 0.95 across pollutants), with a significant modifying influence of meteorological regime. Near-source population is more important for primary coarse particles while population at medium to long distance is more important for primary fine particles and secondary particles. A significant portion of intake fraction (especially for secondary particles and primary fine particles) occurs beyond 500 km of the source, emphasizing the need for detailed long-range dispersion modeling. These findings demonstrate that intake fractions for power plants in China can be

An Application Of Facility Location Models With Hotspot Analysis For Optimal Location Of Abattoir Bio-Energy Plant In Anambra State Of Nigeria

Directory of Open Access Journals (Sweden)

E. C. Chukwuma

2015-08-01

Full Text Available Poor waste management strategy in abattoir in the the study area has needs a major attention considering it negative impacts on man land and water. Sitting of centralized biogas plant in a strategic location in the state would be the major means of combating the environmental challenges of increase in abattoir waste generation as result of population explosion in the state. This study investigates optimal location for sitting central abattoir waste treatment facility in Anambra State of Nigeria using facility location models with hotspot analysis in GIS environment. The result of the study shows that Using centre of gravity model the central location was estimated to be at Xc Yc 6.900953016 6.110157865. Based on inadequacy of the model hotspot analysis operation was done the hotspot analysis delineated clusters of abattoirs significantly higher in bio-wastes production than the overall study area. The hotspot analysis shows that the West regions of the study area has many abattoir that is classified as hotspot abattoirs. Using the hotspot abattoirs as proposed sites for load-distance model three abattoirs were identified as proposed sites- Obosi slaugher house Nkpor Private slaughter house and Oye-olise Ogbunike slaugher house. Their load distance values are 17250.40058 16299.24005 and 18210.14631 respectively. The optimal location for construction of central abattoir bio-waste treatment facility based on the application of these location facility models and hotspot analysis is Nkpor private slaughter house or its environs.

HYDROGEOLOGICAL AND ENGINEERING-GEOLOGICAL CRITERIA FOR THE SELECTION OF NUCLEAR POWER PLANT LOCATION CASE OF THE SAVA RIVERBASIN IN CROATIA

Directory of Open Access Journals (Sweden)

Darko Mayer

1991-12-01

Full Text Available Possible impacts of geological characteristics on safety of nuclear power plants and impacts of nuclear power plants on groundwaters are discussed. Potential locations in view of these criteria are evaluated (the paper is published in Croatian.

A Honey Bee Foraging approach for optimal location of a biomass power plant

Energy Technology Data Exchange (ETDEWEB)

Vera, David; Jurado, Francisco [Dept. of Electrical Engineering, University of Jaen, 23700 EPS Linares, Jaen (Spain); Carabias, Julio; Ruiz-Reyes, Nicolas [Dept. of Telecommunication Engineering, University of Jaen, 23700 EPS Linares, Jaen (Spain)

2010-07-15

Over eight million hectares of olive trees are cultivated worldwide, especially in Mediterranean countries, where more than 97% of the world's olive oil is produced. The three major olive oil producers worldwide are Spain, Italy, and Greece. Olive tree pruning residues are an autochthonous and important renewable source that, in most of cases, farmers burn through an uncontrolled manner. Besides, industrial uses have not yet been developed. The aim of this paper consists of a new calculation tool based on particles swarm (Binary Honey Bee Foraging, BHBF). Effectively, this approach will make possible to determine the optimal location, biomass supply area and power plant size that offer the best profitability for investor. Moreover, it prevents the accurate method (not feasible from computational viewpoint). In this work, Profitability Index (PI) is set as the fitness function for the BHBF approach. Results are compared with other evolutionary optimization algorithms such as Binary Particle Swarm Optimization (BPSO), and Genetic Algorithms (GA). All the experiments have shown that the optimal plant size is 2 MW, PI = 3.3122, the best location corresponds to coordinate: X = 49, Y = 97 and biomass supply area is 161.33 km{sup 2}. The simulation times have been reduced to the ninth of time than the greedy (accurate) solution. Matlab registered is used to run all simulations. (author)

Determination of Effective Criteria for location Selection of WPC Plants from agricultural residues in Iran by AHP Technique

Directory of Open Access Journals (Sweden)

hasan alizadeh

2017-02-01

Full Text Available This study was aimed at determining the effective criteria for location selection of WPC Plants from agricultural residues in Iran. For this purpose, after review and studies papers and books, Six criteria" products and materials, regulations, technical and human, economic, infrastructure and environmental and also 30 sub-criteria were identified. The priority rates of these criteria and sub-criteria were evaluated by AHP technique. The results indicated that among 30 effective sub-criteria in location selection of the WPC plants from agricultural residues, amount of wastes supply (0.087, continuity of wastes supply, cost of wastes supply, amount of sales and export, granted facilities and less Hazards for the environment and forest had the highest priorities, which were rated as 0.071, 0.067, 0.065, 0.064 and 0.062 respectively.

Radioactive characterization of the terrestrial ecosystem in the area of location of the Juragua Nuclear Power Plant

International Nuclear Information System (INIS)

Sibello Hernandez, R.Y.; Alonso Hernandez, C.M.; Diaz Asencio, M.; Cartas Aguila, H. A.

1999-01-01

In this work the results are exposed obtained by the Laboratory of Environmental Surveillance in the radioactive characterization of the existent terrestrial ecosystem in the area of location of the Juragua Nuclear Power Plants in Cienfuegos, Cuba, starting from 1986 and up to 1993

Feasibility Study for Bioethanol Co-Location with a Coal Fired Power Plant: 29 November 2001--28 July 2002

Energy Technology Data Exchange (ETDEWEB)

2002-12-01

This study looks at the feasibility of co-locating 30, 50, and 70 million gallon per year bioethanol facilities with coal fired power plants in Indiana and Nebraska. Corn stover is the feedstock for ethanol production in both cases.

Safety rule of the KTA. Alarm system, staff locator systems, and internal and external communication lines of nuclear power plants. Pt. 1

International Nuclear Information System (INIS)

1977-01-01

This rule aims at stipulating the requirements on type and extent of communication means for personnel within the nuclear power plant, and from the nuclear power plant to the outside. Requirements on design, construction, operating equipment, and alarm and locator system tests for nuclear power plants are defined. The rule applies to stationary nuclear power plants with one power station unit, but not to facilities of process control, radiation protection control, fire protection control, environmental control, and plant security. (orig./HP) [de

Location Study of Solar Thermal Power Plant in the State of Pernambuco Using Geoprocessing Technologies and Multiple-Criteria Analysis

Directory of Open Access Journals (Sweden)

Verônica Wilma B. Azevêdo

2017-07-01

Full Text Available Solar Thermal Technology for the generation of electricity in large scale has been a reality in the world since the 1980s, when the first large-sized solar plants in the United States were introduced. Brazil presents great potential for the development of large-scale projects, although it is noted that the main barriers for the insertion of this technology in Brazilian market are the lack of incentives and goals and associated costs. In a way to contribute to the insertion of solar thermal technology in Brazil, this paper presents a macro-spatial approach, based on the use of Multiple-Criteria Decision Analysis and Geoprocessing, for the location of solar thermal power plants. The applied methodology for Pernambuco, located in the Northeast Region of Brazil, considered the implantation of parabolic trough solar power plant of 80 MW, operating only in solar mode, without heat storage. Based on performed analysis, it was confirmed that Pernambuco presents great potential for the installation of solar power plants, especially in the backlands of Pernambuco. Performed validations in the model demonstrate that the methodology attended the objective once the consistence between the assigned weights to the thematic layers, individually, and the final Map of site suitability were evidenced.

Natural selection and family X location interaction in the common (dry bean plant

Directory of Open Access Journals (Sweden)

Luís Henrique Pirola

2002-01-01

Full Text Available Natural selection takes place while advancing generations of segregant populations of self pollinating species by the population (bulk method. There is evidence that it maintains the individuals with greater grain yield. The question arises whether natural selection preserves the individuals which are more adapted only to the environment where the generation advance occurred, that is, if it contributes to increasing the genotype x environment interaction in the family assessment. This study was carried out to check this hypothesis in the common bean plant using families derived from a segregating population from a cross between the Carioca MG x ESAL 686 cultivars. The segregating populations increase in homozygosity was obtained by the population (bulk method until the F14 generation, in three distinct locations in Minas Gerais state: Lavras, Lambari and Patos de Minas. Forty-seven F14:15 families were randomly taken from the population in each location and later multiplied to obtain F14:16 families. These families were jointly assessed with three controls using a triple 12 x 12 lattice design in the three locations of generation advance in the wet season of 1998/1999. All the estimated parameters showed that while advancing segregant populations by the population (bulk method, natural selection acted to preserve the individuals which are more adapted to the environment in which they were advanced.

Development of valuation method for location planning and dimensioning of hydrogen plants; Entwicklung einer Bewertungsmethodik zur Standortplanung und Dimensionierung von Wasserstoffanlagen

Energy Technology Data Exchange (ETDEWEB)

Guenther, Thomas

2014-02-04

Common decisions for locations of production plants are based on criteria such as availability of commodities, energy, infrastructure and costs related with these. Sizing of product capacities depends on other things such as production quantities to be sold and profits to be obtained. The condition is an permanent availability of the required energy. For concepts of using surplus renewable energies especially wind energy for hydrogen production common methods are only partly suitable. Thus in this work an evaluation methodology was developed which integrated duration and amount of available energy for decisions of locations and dimensioning of the plant. Initially the hydrogen plant is modularised and segmented to the sub processed energy supply, water supply, water electrolyses, cooling, storing and compression for transport. After the specification of technological and economical parameters, the material and energy streams as well as the costs are calculated for every individual plant. Based on the given conditions, the configuration of plant and also the investigation of site-specific production costs is done. By variation of technology and costs parameters, feasibility studies and different operating scenarios can be demonstrated. The application of this evaluation methodology is demonstrated by case studies. A hydrogen plant situated at an industry park serves as a reference plant for the continuous operation with grid energy. Using a wind energy propelled hydrogen plant as an example, the effects of amount and duration of the usable energy are shown. Based on predefined hydrogen prices, the correlation between optimal plant capacity and plant utilization is described and the difference between the predefined price and the operation costs is calculated. This difference can be used to finance the wind farm operation. The results serves among others for the development of optimal operation concepts and also for first cost estimations, prior to a detailed plant

A geographic information system for gas power plant location using analytical hierarchy process and fuzzy logic

International Nuclear Information System (INIS)

Alavipoor, F. S.; Karimi, S.; Balist, J.; Khakian, A. H.

2016-01-01

This research recommends a geographic information system-based and multi-criteria evaluation for locating a gas power plant in Natanz City in Iran. The multi-criteria decision framework offers a hierarchy model to select a suitable place for a gas power plant. This framework includes analytic hierarchy process, fuzzy set theory and weighted linear combination. The analytic hierarchy process was applied to compare the importance of criteria among hierarchy elements classified by environmental group criteria. In the next step, the fuzzy logic was used to regulate the criteria through various fuzzy membership functions and fuzzy layers were formed by using fuzzy operators in the Arc-GIS environment. Subsequently, they were categorized into 6 classes using reclassify function. Then weighted linear combination was applied to combine the research layers. Finally, the two approaches were analyzed to find the most suitable place to set up a gas power plant. According to the results, the utilization of GAMMA fuzzy operator was shown to be suitable for this site selection.

Kansas Power Plants

Data.gov (United States)

Kansas Data Access and Support Center — The Kansas Power Plants database depicts, as point features, the locations of the various types of power plant locations in Kansas. The locations of the power plants...

Lightning Location System Data from Wind Power Plants Compared to Meteorological Conditions of Warm- and Cold Thunderstorm Events

DEFF Research Database (Denmark)

Vogel, Stephan; Lopez, Javier; Garolera, Anna Candela

2016-01-01

of topography, height above mean sea level (AMSL), and average ground flash density. For three sites, the most severe lightning events have been identified during the warm and cold months whereas the other two locations exhibit severe lightning detections mainly during the warm months. In this work severity......Five years of Lightning Location System (LLS) data from five different wind turbine sites in Europe are analysed. The sites are located in Croatia, Italy, Spain, France and one offshore wind power plant in the North sea. Each location exhibits individual characteristic properties in terms...... of such an episode can vary from tens of minutes to several hours in the case of new storms being continuously developed in the same area. The distance of the charge separating -10◦ C and the ground is usually larger than 3000 meters. This analyse provides information about the different thunderstorm types which...

Organic farming benefits local plant diversity in vineyard farms located in intensive agricultural landscapes.

Science.gov (United States)

Nascimbene, Juri; Marini, Lorenzo; Paoletti, Maurizio G

2012-05-01

The majority of research on organic farming has considered arable and grassland farming systems in Central and Northern Europe, whilst only a few studies have been carried out in Mediterranean agro-systems, such as vineyards, despite their economic importance. The main aim of the study was to test whether organic farming enhances local plant species richness in both crop and non-crop areas of vineyard farms located in intensive conventional landscapes. Nine conventional and nine organic farms were selected in an intensively cultivated region (i.e. no gradient in landscape composition) in northern Italy. In each farm, vascular plants were sampled in one vineyard and in two non-crop linear habitats, grass strips and hedgerows, adjacent to vineyards and therefore potentially influenced by farming. We used linear mixed models to test the effect of farming, and species longevity (annual vs. perennial) separately for the three habitat types. In our intensive agricultural landscapes organic farming promoted local plant species richness in vineyard fields, and grassland strips while we found no effect for linear hedgerows. Differences in species richness were not associated to differences in species composition, indicating that similar plant communities were hosted in vineyard farms independently of the management type. This negative effect of conventional farming was probably due to the use of herbicides, while mechanical operations and mowing regime did not differ between organic and conventional farms. In grassland strips, and only marginally in vineyards, we found that the positive effect of organic farming was more pronounced for perennial than annual species.

Locating techniques for nuclear power stations

International Nuclear Information System (INIS)

Hayashi, Masao

1983-01-01

The basic thought in locating nuclear power stations is to examine carefully the suitability of sites and the safety of plants, and in the end, to perfect the safety of public. In Japan, effort is exerted to obtain the trust of local people by carrying out investigation, research and examination from respective standpoints of the government, institutes and industries. The author has engaged in the standardization of the investigation, test and analysis regarding the aseismatic capability of ground, the verifying project in Tadotsu of the coupled vibration of ground and structures, the evaluation of the performance of large vibration tables, the future concept of new locating procedure and so on in the last more than ten years. The technological classification of ground, the technological meaning of active faults, the procedure of the aseismatic design of plants, the difference of earthquake input force according to various locating methods, 12 rules regarding the attenuation of vibration of ground, and the concept of new locating method in the 21st century are explained. As the new locating techniques applicable to central Japan, diluvial ground location, floating location in tunnels, underground location, offshore location and so on must be promoted. (Kako, I.)

High yielding tropical energy crops for bioenergy production: Effects of plant components, harvest years and locations on biomass composition.

Science.gov (United States)

Surendra, K C; Ogoshi, Richard; Zaleski, Halina M; Hashimoto, Andrew G; Khanal, Samir Kumar

2018-03-01

The composition of lignocellulosic feedstock, which depends on crop type, crop management, locations and plant parts, significantly affects the conversion efficiency of biomass into biofuels and biobased products. Thus, this study examined the composition of different parts of two high yielding tropical energy crops, Energycane and Napier grass, collected across three locations and years. Significantly higher fiber content was found in the leaves of Energycane than stems, while fiber content was significantly higher in the stems than the leaves of Napier grass. Similarly, fiber content was higher in Napier grass than Energycane. Due to significant differences in biomass composition between the plant parts within a crop type, neither biological conversion, including anaerobic digestion, nor thermochemical pretreatment alone is likely to efficiently convert biomass components into biofuels and biobased products. However, combination of anaerobic digestion with thermochemical conversion technologies could efficiently utilize biomass components in generating biofuels and biobased products. Copyright © 2017 Elsevier Ltd. All rights reserved.

Location condition of nuclear power generation at a viewpoint of location area

International Nuclear Information System (INIS)

Kawase, Kazuharu

1999-01-01

In the thirty years memorial meeting of the National Nuclear Power Generation located Commune Conference (NNGC) held in October, 1998, an extremely important fact was clarified, relation deeply to main aim of NNGC that permanent development was not promised at the location area even if a nuclear power plant was constructed there. Therefore, it is required that Japan government receives operation of three laws on electric source development as soon as possible, establishes a basic target on permanent area promotion in the nuclear power generation located commune, realizes some examples on development of the commune together with nuclear power generation and intends to promoted its location. (G.K.)

Modeling future power plant location patterns. Final report

International Nuclear Information System (INIS)

Eagles, T.W.; Cohon, J.L.; ReVelle, C.

1979-04-01

The locations of future energy facilities must be specified to assess the potential environmental impact of those facilities. A computer model was developed to generate probable locations for the energy facilities needed to meet postulated future energy requirements. The model is designed to cover a very large geographical region. The regional demand for baseload electric generating capacity associated with a postulated demand growth rate over any desired time horizon is specified by the user as an input to the model. The model uses linear programming to select the most probable locations within the region, based on physical and political factors. The linear program is multi-objective, with four objective functions based on transmission, coal supply, population proximity, and water supply considerations. Minimizing each objective function leads to a distinct set of locations. The user can select the objective function or weighted combination of objective functions most appropriate to his interest. Users with disparate interests can use the model to see the locational changes which result from varying weighting of the objective functions. The model has been implemented in a six-state mid-Atlantic region. The year 2000 was chosen as the study year, and a test scenario postulating 2.25% growth in baseload generating capacity between 1977 and 2000 was chosen. The scenario stipulatedthat this capacity be 50% nuclear and 50% coal-fired. Initial utility reaction indicates the objective based on transmission costs is most important for such a large-scale analysis

Application of a Dynamic Fuzzy Search Algorithm to Determine Optimal Wind Plant Sizes and Locations in Iowa

International Nuclear Information System (INIS)

Milligan, M. R.; Factor, T.

2001-01-01

This paper illustrates a method for choosing the optimal mix of wind capacity at several geographically dispersed locations. The method is based on a dynamic fuzzy search algorithm that can be applied to different optimization targets. We illustrate the method using two objective functions for the optimization: maximum economic benefit and maximum reliability. We also illustrate the sensitivity of the fuzzy economic benefit solutions to small perturbations of the capacity selections at each wind site. We find that small changes in site capacity and/or location have small effects on the economic benefit provided by wind power plants. We use electric load and generator data from Iowa, along with high-quality wind-speed data collected by the Iowa Wind Energy Institute

Application of a Dynamic Fuzzy Search Algorithm to Determine Optimal Wind Plant Sizes and Locations in Iowa

Energy Technology Data Exchange (ETDEWEB)

Milligan, M. R., National Renewable Energy Laboratory; Factor, T., Iowa Wind Energy Institute

2001-09-21

This paper illustrates a method for choosing the optimal mix of wind capacity at several geographically dispersed locations. The method is based on a dynamic fuzzy search algorithm that can be applied to different optimization targets. We illustrate the method using two objective functions for the optimization: maximum economic benefit and maximum reliability. We also illustrate the sensitivity of the fuzzy economic benefit solutions to small perturbations of the capacity selections at each wind site. We find that small changes in site capacity and/or location have small effects on the economic benefit provided by wind power plants. We use electric load and generator data from Iowa, along with high-quality wind-speed data collected by the Iowa Wind Energy Institute.

Application of ant colony optimization in NPP classification fault location

International Nuclear Information System (INIS)

Xie Chunli; Liu Yongkuo; Xia Hong

2009-01-01

Nuclear Power Plant is a highly complex structural system with high safety requirements. Fault location appears to be particularly important to enhance its safety. Ant Colony Optimization is a new type of optimization algorithm, which is used in the fault location and classification of nuclear power plants in this paper. Taking the main coolant system of the first loop as the study object, using VB6.0 programming technology, the NPP fault location system is designed, and is tested against the related data in the literature. Test results show that the ant colony optimization can be used in the accurate classification fault location in the nuclear power plants. (authors)

Plant location and extraction procedure strongly alter the antimicrobial activity of murta extracts

DEFF Research Database (Denmark)

Shene, Carolina; Reyes, Agnes K.; Villarroel, Mario

2009-01-01

plants grown nearer to the mountain (58 mg GAE/g murta), subjected to extreme summer/winter-day/night temperature changes and rainy regime. Extracts from leaves collected in the valley and coast contained 46 and 40 mg GAE/g murta, respectively. A mixture of 50% ethanol/water was the most efficient......Leaves and fruits of Murta (Ugni Molinae Turcz.) growing in three locations of Chile with diverse climatic conditions were extracted by using ethanol/water mixtures at different ratios and the antimicrobial activity was assessed. Extracts containing the highest polyphenolic content were from murta...... in extracting polyphenols, showing pure solvents-both water and ethanol-a lower extraction capacity. No correlation between antioxidant capacity and polyphenolic content was found. Extracts from Murta leaves provoked a decrease in the growing of Pseudomonas aeruginosa, Klebsiella pneumoniae and Staphylococcus...

Anaerobic co-digestion plants for the revaluation of agricultural waste: Sustainable location sites from a GIS analysis.

Science.gov (United States)

Villamar, Cristina Alejandra; Rivera, Diego; Aguayo, Mauricio

2016-04-01

The aim of this study was to establish sustainably feasible areas for the implementation of anaerobic co-digestion plants for agricultural wastes (cattle/swine slurries and cereal crop wastes). The methodology was based on the use of geographic information systems (GIS), the analytic hierarchy process (AHP) and map algebra generated from hedges related to environmental, social and economic constraints. The GIS model obtained was applied to a region of Chile (Bío Bío Region) as a case study showing the energy potential (205 MW-h) of agricultural wastes (swine/cattle manures and cereal crop wastes) and thereby assessing its energy contribution (3.5%) at country level (Chile). From this model, it was possible to spatially identify the influence of each factor (environmental, economic and social) when defining suitable areas for the siting of anaerobic co-digestion plants. In conclusion, GIS-based models establish appropriate areas for the location of anaerobic co-digestion plants in the revaluation of agricultural waste from the production of energy through biogas production. © The Author(s) 2016.

Perspectives on Spatial Decision Support Concerning Location of Biogas Production

DEFF Research Database (Denmark)

Bojesen, Mikkel

in biogas production. This ambition requires that more than 20 new large scale centralised biogas plants are built. The location of these plants is associated with a number of externalities and uncertainties and the existing biogas sector struggles to establish itself as a viable energy producing sector....... Meanwhile planners and decision makers struggle to find sustainable locations that comprehensively balance the multiple concerns the location of biogas facilities includes. This PhD project examines how spatial decision support models can be used to ensure sustainable locations of future biogas plants......, understand the industrial economic aspects of such a role. Through the use of spatial multi-criteria evaluation models stakeholder preferences to decision criteria are included in a sustainable biogas facility location analysis. By the use of these models it is demonstrated how overall biogas production...

The influence of geographic location on population exposure to emissions from power plants throughout China

Energy Technology Data Exchange (ETDEWEB)

Zhou, Y.; Levy, J.I.; Evans, J.S.; Hammitt, J.K. [Harvard University, Boston, MA (United States). School of Public Health

2006-04-15

This analysis seeks to evaluate the influence of emission source location on population exposure in China to fine particles and sulfur dioxide. We use the concept of intake fraction, defined as the fraction of material or its precursor released from a source that is eventually inhaled or ingested by a population. We select 29 power-plant sites throughout China and estimate annual average intake fractions at each site, using identical source characteristics to isolate the influence of geographic location. In addition, we develop regression models to interpret the intake fraction values and allow for extrapolation to other sites. To model the concentration increase due to emissions from selected power plants, we used a detailed long-range atmospheric dispersion model, CALPUFF. Primary fine particles have the highest average intake fraction (1 x 10{sup -5}), followed by sulfur dioxide (5 x 10{sup -6}), sulfate from sulfur dioxide (4 x 10{sup -6}), and nitrate from nitrogen oxides (4 x 10{sup -6}). In the regression analysis, the independent variables are meteorological proxies (such as climate region and precipitation) and population at various distances from the source. We find that population terms can explain a substantial percentage of variability in the intake fraction for all pollutants, with a significant modifying influence of meteorological regime. Near-source population is more important for primary coarse particles while population at medium to long distance is more important for primary fine particles and secondary particles. A significant portion of intake fraction (especially for secondary particles and primary fine particles) occurs beyond 500 km of the source, emphasizing the need for detailed long-range dispersion modeling.

The location and nature of accumulated phosphorus in seven sludges from activated sludge plants which exhibited enhanced phosphorus removal

International Nuclear Information System (INIS)

Buchan, L.

1981-01-01

Electron microscopy combined with the energy dispersive analysis of X-rays (EDX) has been used to examine the nature of the phosphorus accumulated in sludges from seven activated sludge plants exhibiting enhanced phosphorus removal. Large phosphorus accumulations were located in identical structures in the sludges examined. The phosphorus was located in large electron-dense bodies, within large bacterial cells which were characteristically grouped in clusters. The calcium:phosphorus ratio of these electron-dense bodies precluded them from being any form of calcium phosphate precipitate. Quantitative analysis indicated that the electron-dense bodies contained in excess of 30% phosphorus. The results obtained are supportive of a biological mechanism of enhanced phosphorus uptake in activated sludge

Modeling a four-layer location-routing problem

Directory of Open Access Journals (Sweden)

Mohsen Hamidi

2012-01-01

Full Text Available Distribution is an indispensable component of logistics and supply chain management. Location-Routing Problem (LRP is an NP-hard problem that simultaneously takes into consideration location, allocation, and vehicle routing decisions to design an optimal distribution network. Multi-layer and multi-product LRP is even more complex as it deals with the decisions at multiple layers of a distribution network where multiple products are transported within and between layers of the network. This paper focuses on modeling a complicated four-layer and multi-product LRP which has not been tackled yet. The distribution network consists of plants, central depots, regional depots, and customers. In this study, the structure, assumptions, and limitations of the distribution network are defined and the mathematical optimization programming model that can be used to obtain the optimal solution is developed. Presented by a mixed-integer programming model, the LRP considers the location problem at two layers, the allocation problem at three layers, the vehicle routing problem at three layers, and a transshipment problem. The mathematical model locates central and regional depots, allocates customers to plants, central depots, and regional depots, constructs tours from each plant or open depot to customers, and constructs transshipment paths from plants to depots and from depots to other depots. Considering realistic assumptions and limitations such as producing multiple products, limited production capacity, limited depot and vehicle capacity, and limited traveling distances enables the user to capture the real world situations.

Reliability of the seismic characteristics in the nuclear power plant location; Pouzdanost seizmickih karakteristika pri lociranju nuklearne elektrane

Energy Technology Data Exchange (ETDEWEB)

Marsicanin, B [Institut za Nuklearne Nauke Boris Kidric, Belgrade (Yugoslavia)

1982-07-01

Seismic characteristics for a nuclear power plant location are partly obtained from the analysis of past earthquakes. Data from older history concern damages, the newer data are in the form of seismic records. These two sources are often had to correlate, and the data dissipation is very large. Therefore these, rather unreliable data are not a convenient base for the precise anti-seismic analysis. A redistribution of efforts in order to get more reliable basic data seems necessary. (author)

Model for 3D-visualization of streams and techno-economic estimate of locations for construction of small hydropower plants

International Nuclear Information System (INIS)

Izeiroski, Subija

2012-01-01

The main researches of this dissertation are focused to a development of a model for preliminary assesment of the hydro power potentials for small hydropower plants construction using Geographic Information System - GIS. For this purpose, in the first part of dissertation is developed a contemporary methodological approach for 3D- visualization of the land surface and river streams in a GIS platform. In the methodology approach, as input graphical data are used digitized maps in scale 1:25000, where each map covers an area of 10x14 km and consists of many layers with graphic data in shape (vector) format. Using GIS tools, from the input point and isohyetal contour data layers with different interpolation techniques have been obtained digital elevation model - DEM, which further is used for determination of additional graphic maps with useful land surface parameters such as: slope raster maps, hill shade models of the surface, different maps with hydrologic parameters and many others. The main focus of researches is directed toward the developing of contemporary methodological approaches based on GIS systems, for assessment of the hydropower potentials and selection of suitable location for small hydropower plant construction - SHPs, and especially in the mountainous hilly area that are rich with water resources. For this purpose it is done a practical analysis at a study area which encompasses the watershed area of the Brajchanska River at the east part of Prespa Lake. The main accent considering the analysis of suitable locations for SHP construction is set to the techno-engineering criteria, and in this context is made a topographic analysis regarding the slope (gradient) either of all as well of particular river streams. It is also made a hydrological analysis regarding the flow rates (discharges). The slope analysis is executed at a pixel (cell) level a swell as at a segment (line) level along a given stream. The slope value at segment level gives in GIS

The Potential Pathways of Radionuclide Transformations On The Location Candidate of Nuclear Power Plants in Muria Peninsula

International Nuclear Information System (INIS)

Simandjuntak, A.G.; Syahrir

1998-01-01

The potential pathways of radionuclide transformations on the location candidate of nuclear power plants in Muria peninsula proposed to explain the potential of radionuclide pathways in the ecosystem to human based on annual effective dose calculations with elimination factor ≥ 1 of dose limit 50 mSv per year. The effective dose equivalent calculations used the program package Genll. The datum found from Bureau of Statistic Centre and NEWJEC was taken into calculations. The result of this study is very useful for radiological impact and environmental impact analysis. (author)

Testing of five methods for the control of zebra mussels in cooling circuits of power plants located on the Moselle river

International Nuclear Information System (INIS)

Khalanski, M.

1993-10-01

Bioassays have been conducted on site at the Cattenom nuclear power plant located on the Moselle River (in northeast France) to control mussels in auxiliary plant circuits. During the course of a two-year program, five methods were tested: - thermal treatment (33 deg to 40 deg C), - high dosage chlorination (> 50 ppm), - low dosage chlorine dioxide, - potassium salt (KCI > 100 ppm), - one organic compound (Mexel 432). This note presents a comparison of the treatments shown to be most effective, on the basis of technical feasibility, cost and environmental acceptability. (author). 8 figs., 10 refs., 3 tabs

Modeling identifies optimal fall planting times and irrigation requirements for canola and camelina at locations across California

Directory of Open Access Journals (Sweden)

Nicholas George

2017-06-01

Full Text Available In California, Brassica oilseeds may be viable crops for growers to diversify their cool-season crop options, helping them adapt to projected climate change and irrigation water shortages. Field trials have found germination and establishment problems in some late-planted canola, but not camelina at the same locations. We used computer modeling to analyze fall seedbed conditions to better understand this phenomenon. We found seedbeds may be too dry, too cold, or both, to support germination of canola during late fall. Based on seedbed temperatures only, canola should be sown no later than the last week of November in the Central Valley. Camelina has broader temperature and moisture windows for germination and can be sown from October to December with less risk, but yields of camelina are lower than canola yields. In areas without irrigation, growers could plant canola opportunistically when seedbed conditions are favorable and use camelina as a fallback option.

Influence of plant roots upon the mobility of radionuclides in soil, with respect to location of contamination below the surface

International Nuclear Information System (INIS)

Harvey, N.W.; Shaw, G.; Bell, N.J.B.

1997-01-01

The movement of 85 Sr, 137 Cs, 54 Mn and 60 Co in the 50 cm soil profile was studied with and without the presence of plant roots (triticum aestivum) in order to investigate the influence of roots and depth contamination upon the migration of radionuclides. The water table was maintained manually at 3 cm from the bottom. The physicochemical characteristics (E h Fe -2 , NH 4 + , pH and moisture content) as well as the total and extractable radioactivity were investigated. In the discrete contamination, where the location of contamination varied within the soil profile (0-5, 25-30 or 45-50 cm from the top), the influence of location upon the movement of these radionuclides was also studied. It was found that the changes in the soil physicochemical characteristics influenced the mobility of the four radionuclides. The extractability of 54 Mn and 60 Co was significantly increased in the reducing region of the soil, whereas that of 85 Sr, 137 Cs was not. Plant roots excerted significant effects upon the soil characteristics, via, reducing the E h pH and moisture content of the soil; increasing the extractability of both 54 Mn and 60 Co from the depth of 35 cm downwards. Radionuclide migration occurred via physicochemical and biological transport. The biological transport via plant roots was of particular importance for 137 Cs. Location of contamination had a significant influence upon the mobility of radionuclides. The migration of radionuclides was in the sequence of contamination in middle > bottom > top. The degree of the influence varied with radionuclides concerned. In the top layer contamination, the rank of the migration from the contamination layers, on the other hand 54 Mn, 60 Co and 137 Cs were more mobile and the movement was: 85 Sr ∼ 54 Mn ∼ 60 Co > 137 Cs. In the middle and bottom contamination layers, on the other hand, 54 Mn and 60 Co and 137 Cs were more mobile and the movement was 85 Sr ∼ 54 Mn ∼ 60 Co ∼ 137 Cs. (author)

GIS Methodology for Location of Biomass Power Plants Via Multi -Criteria Evaluation and Network Analysis. Location-Allocation Models for Forest Biomass Use; Metodologia SIG para la Localizacion de Centrales de Biomasa mediante Evaluacion Multicriterio y Analisis de Redes. Modelos de Localizacion-Asignacion para el Aprovechamiento de Biomasa Forestal

Energy Technology Data Exchange (ETDEWEB)

Paz, C de la; Dominguez, J; Perez, M E

2013-02-01

The main purpose of this study is to find optimal areas for the installation of Biomass Plants for electric generation and grid connected. In order to achieve this goal, a methodology based on Multi-Criteria Evaluation (MCE) and implemented by means a Geographic Information System (GIS) has been developed. Factors and restrictions for biomass resource and power plants location of biomass have been obtained through the dataset. The methodology output includes maps of greater aptitude areas for resource use (forest biomass available), as well as suitable locations for the placement of Forest Biomass facilities. Both cartographic products have been related by means Network Analysis. It generates Location-Allocation Models which allows locating Forest Biomass Facilities according with an optimization of the supply chain from the resource areas. (Author)

Coal-fired Power Plants with Flexible Amine-based CCS and Co-located Wind Power: Environmental, Economic and Reliability Outcomes

Science.gov (United States)

Bandyopadhyay, Rubenka

Carbon Capture and Storage (CCS) technologies provide a means to significantly reduce carbon emissions from the existing fleet of fossil-fired plants, and hence can facilitate a gradual transition from conventional to more sustainable sources of electric power. This is especially relevant for coal plants that have a CO2 emission rate that is roughly two times higher than that of natural gas plants. Of the different kinds of CCS technology available, post-combustion amine based CCS is the best developed and hence more suitable for retrofitting an existing coal plant. The high costs from operating CCS could be reduced by enabling flexible operation through amine storage or allowing partial capture of CO2 during high electricity prices. This flexibility is also found to improve the power plant's ramp capability, enabling it to offset the intermittency of renewable power sources. This thesis proposes a solution to problems associated with two promising technologies for decarbonizing the electric power system: the high costs of the energy penalty of CCS, and the intermittency and non-dispatchability of wind power. It explores the economic and technical feasibility of a hybrid system consisting of a coal plant retrofitted with a post-combustion-amine based CCS system equipped with the option to perform partial capture or amine storage, and a co-located wind farm. A techno-economic assessment of the performance of the hybrid system is carried out both from the perspective of the stakeholders (utility owners, investors, etc.) as well as that of the power system operator. (Abstract shortened by ProQuest.).

Preliminary safety analysis of a PBMR supplying process heat to a co-located ethylene production plant

International Nuclear Information System (INIS)

Scarlat, Raluca O.; Cisneros, Anselmo T.; Koutchesfahani, Tawni; Hong, Rada; Peterson, Per F.

2012-01-01

This paper considers the safety analysis and licensing approach for co-locating a pebble bed modular reactor (PBMR) to provide process heat to an ethylene production unit. The PBMR is an advanced nuclear reactor design that provides 400 MW of thermal energy. Ethylene production is an energy intensive process that utilizes large gas furnaces to provide the heat for the process. Coupling a PBMR with an ethylene production plant would open a new market for nuclear power, and would provide the chemical industry with a cleaner power source, helping to achieve the Clean Air Act standards, and eliminating the 0.5 ton of CO 2 emissions per ton of produced ethylene. Our analysis uses the Chevron Phillips chemical plant in Sweeney, TX as a prototypical site. The plant has four ethylene production trains, with a total power consumption of 2.4 GW, for an ethylene output of 3.7 million tons per year, 4% of the global ethylene production capacity. This paper proposes replacement of the gas furnaces by low-emission PBMR modules, and presents the safety concerns and risk mitigation and management options for this coupled system. Two coupling design options are proposed, and the necessary changes to the design basis events and severe accidents for the PBMR licensing application are discussed. A joint effort between the chemical and the nuclear entities to optimize the coupling design, establish preventive maintenance procedures, and develop emergency response plans for both of the units is recommended.

Preliminary safety analysis of a PBMR supplying process heat to a co-located ethylene production plant

Energy Technology Data Exchange (ETDEWEB)

Scarlat, Raluca O., E-mail: rscarlat@nuc.berkeley.edu [University of California Berkeley, Nuclear Engineering, 4118 Etcheverry Hall, Berkeley, CA 94720 (United States); Cisneros, Anselmo T. [University of California Berkeley, Nuclear Engineering, 4118 Etcheverry Hall, Berkeley, CA 94720 (United States); Koutchesfahani, Tawni [University of California, Chemical and Biomolecular Engineering, 201 Gilman Hall, Berkeley, CA 94720 (United States); Hong, Rada; Peterson, Per F. [University of California Berkeley, Nuclear Engineering, 4118 Etcheverry Hall, Berkeley, CA 94720 (United States)

2012-10-15

This paper considers the safety analysis and licensing approach for co-locating a pebble bed modular reactor (PBMR) to provide process heat to an ethylene production unit. The PBMR is an advanced nuclear reactor design that provides 400 MW of thermal energy. Ethylene production is an energy intensive process that utilizes large gas furnaces to provide the heat for the process. Coupling a PBMR with an ethylene production plant would open a new market for nuclear power, and would provide the chemical industry with a cleaner power source, helping to achieve the Clean Air Act standards, and eliminating the 0.5 ton of CO{sub 2} emissions per ton of produced ethylene. Our analysis uses the Chevron Phillips chemical plant in Sweeney, TX as a prototypical site. The plant has four ethylene production trains, with a total power consumption of 2.4 GW, for an ethylene output of 3.7 million tons per year, 4% of the global ethylene production capacity. This paper proposes replacement of the gas furnaces by low-emission PBMR modules, and presents the safety concerns and risk mitigation and management options for this coupled system. Two coupling design options are proposed, and the necessary changes to the design basis events and severe accidents for the PBMR licensing application are discussed. A joint effort between the chemical and the nuclear entities to optimize the coupling design, establish preventive maintenance procedures, and develop emergency response plans for both of the units is recommended.

Ethnic and locational differences in ecosystem service values

DEFF Research Database (Denmark)

Cuni Sanchez, Aida; Pfeifer, Marion; Marchant, Rob

2016-01-01

location. Preferred plant species for food, fodder, medicine resources, poles and firewood followed the same pattern. Our results showed that ethnicity and location affect ecosystem services' identification and importance ranking. This should be taken into account by decision-makers, e.g. as restricted......Understanding cultural preferences toward different ecosystem services is of great importance for conservation and development planning. While cultural preferences toward plant species have been long studied in the field of plant utilisation, the effects of ethnicity on ecosystem services...... identification and valuation has received little attention. We assessed the effects of ethnicity toward different ecosystem services at three similar forest islands in northern Kenya inhabited by Samburu and Boran pastoralists. Twelve focus groups were organised in each mountain, to evaluate the ecosystem...

Grass plants crop water consumption model in urban parks located ...

African Journals Online (AJOL)

The most important issue is the to use of urban space to increase the number and size of green areas. As well as another important issue is to work towards maintaining these spaces. One such important effort is to meet the water needs of plants. Naturally, the amount of water needed by plants depends on the species.

Memory for location and visual cues in white-eared hummingbirds Hylocharis leucotis

Directory of Open Access Journals (Sweden)

Guillermo PÉREZ, Carlos LARA, José VICCON-PALE, Martha SIGNORET-POILLON

2011-08-01

Full Text Available In nature hummingbirds face floral resources whose availability, quality and quantity can vary spatially and temporally. Thus, they must constantly make foraging decisions about which patches, plants and flowers to visit, partly as a function of the nectar reward. The uncertainty of these decisions would possibly be reduced if an individual could remember locations or use visual cues to avoid revisiting recently depleted flowers. In the present study, we carried out field experiments with white-eared hummingbirds Hylocharis leucotis, to evaluate their use of locations or visual cues when foraging on natural flowers Penstemon roseus. We evaluated the use of spatial memory by observing birds while they were foraging between two plants and within a single plant. Our results showed that hummingbirds prefer to use location when foraging in two plants, but they also use visual cues to efficiently locate unvisited rewarded flowers when they feed on a single plant. However, in absence of visual cues, in both experiments birds mainly used the location of previously visited flowers to make subsequent visits. Our data suggest that hummingbirds are capable of learning and employing this flexibility depending on the faced environmental conditions and the information acquired in previous visits [Current Zoology 57 (4: 468–476, 2011].

Ecological analysis of plant cover of the permanent grassland ecosystem located in the vicinity of Novi Kneževac, Serbia

Directory of Open Access Journals (Sweden)

Knežević Aleksa

2012-01-01

Full Text Available A total of 205 taxa and stands of 12 plant communities were found to comprise the plant cover of the permanent grassland on the solonetz and solonchakic solonetz soils located in the vicinity of the town of Novi Kneževac (Vojvodina Province, Serbia. The registered taxa included 177 plant species, six subspecies, eight varieties, 13 forms and one lusus. The ecological analysis of the flora involved 191 taxa. That group consisted of 177 species, six subspecies, three varieties and five forms. The three varieties, Aster tripolium L. var. pannonicus ( Jacq. Beck, Chenopodium rubrum L. subsp. botryoides Sm. var. crassifolium (Hornem Kov. and Sonchus arvensis L. var. uliginosus (M.B. Grec. were used for analysis because their higher taxonomic categories were not recorded in the studied flora. The five forms, Aster sedifolius L. f. subsquamosus Soy, Bromus commutatus Schrad. f. violaceus Podp., Mentha aquatica L. f. erromera Top., Poa bulbosa L. f. vivipara Koel. and Scleranthus annus L. f. minimus Schur., were used for the same reason. The ecological analysis encompassed stands of all 12 recorded communities, i.e. ass. Scirpo-Phragmitetum W. Koch 1926, ass. Bolboschoenetum maritimi continentale Soy (1927 1957, ass. Acorelletum pannonici Soy (1939 1947, ass. Puccinelletum limosae (Rapcs. 1927 Soy 1930, ass. Pholiuro-Plantaginetum tenuiflorae (Rapcs. 1927 Wendel. 1943, ass. Hordeetum histricis (Soy 1933 Wendel. 1943, ass. Camphorosmetum annuae (Rapcs. 1916 Soy 1933 corr. Soy 1938, ass. Agrostio-Alopecuretum pratensis Soy (1933 1947, ass. Agrostio-Eleochariti-Alopecuretu geniculati (Magyar1928 Soy (1939 1947, ass. Artemisio-Festucetum pseudovinae (Magyar 1928 Soy 1945, ass. Achilleo-Festucetum pseudovinae (Magyar 1928 Soy 1945 and ass. Festuco-Andropogonetum ischaemi Vučk. 1985. The ecological analysis of the plant cover indicated that halophytes made 30.37% of the flora of the permanent grassland near the town of Novi Kneževac, and that the stands of

Health effects due to the release of iodine 129 from the marine outlet for the reprocessing plant located at La Hague

International Nuclear Information System (INIS)

Robeau, D.; Calmet, D.

1985-02-01

The study contained in this report estimates the health effects in terms of doses to the populations due to the release of Iodine 129 from the marine outlet for the reprocessing plant located at La Hague. The release taken into account is due to the normal functioning of the plant, which introduces a consistent contamination of the English channel during the life of the plant which is thirty years. The annual release of Iodine 129, as assumed by the operating staff, is equal to either 1,662.10 12 Bq or 45 Ci. The dose equivalent to the thyroid of the concerned population due to normal consummation of marine products (fish, shell-fish, mollusc) are very low as compared to the 6.10 -4 limit of dose authorized for the public in the actual regulation. The effective dose equivalent has been estimated at 4.27.10 -7 Sv [fr

Optimal sizing and location of SVC devices for improvement of voltage profile in distribution network with dispersed photovoltaic and wind power plants

International Nuclear Information System (INIS)

Savić, Aleksandar; Đurišić, Željko

2014-01-01

Highlights: • Significant voltage variations in a distribution network with dispersed generation. • The use of SVC devices to improve the voltage profiles are an effective solution. • Number, size and location of SVC devices are optimized using genetic algorithm. • The methodology is presented on an example of a real distribution system in Serbia. - Abstract: Intermittent power generation of wind turbines and photovoltaic plants creates voltage disturbances in power distribution networks which may not be acceptable to the consumers. To control the deviations of the nodal voltages, it is necessary to use fast dynamic control of the reactive power in the distribution network. Implementation of the power electronic devices, such as Static Var Compensator (SVC), enables effective dynamic state as well as a static state of the nodal voltage control in the distribution network. This paper analyzed optimal sizing and location of SVC devices by using genetic algorithm, to improve nodal voltages profile in a distribution network with dispersed photovoltaic and wind power plants. Practical application of the developed methodology was tested on an example of a real distribution network

Plant host finding by parasitic plants: a new perspective on plant to plant communication.

Science.gov (United States)

Mescher, Mark C; Runyon, Justin B; De Moraes, Consuelo M

2006-11-01

Plants release airborne chemicals that can convey ecologically relevant information to other organisms. These plant volatiles are known to mediate a large array of, often complex, interactions between plants and insects. It has been suggested that plant volatiles may have similar importance in mediating interactions among plant species, but there are few well-documented examples of plant-to-plant communication via volatiles, and the ecological significance of such interactions has been much debated. To date, nearly all studies of volatile-mediated interactions among plant species have focused on the reception of herbivore-induced volatiles by neighboring plants. We recently documented volatile effects in another system, demonstrating that the parasitic plant Cuscuta pentagona uses volatile cues to locate its hosts. This finding may broaden the discussion regarding plant-to-plant communication, and suggests that new classes of volatile-meditated interactions among plant species await discovery.

A fuzzy approach to a multiple criteria and Geographical Information System for decision support on suitable locations for biogas plants

DEFF Research Database (Denmark)

Franco, Camilo; Bojesen, Mikkel; Hougaard, Jens Leth

2015-01-01

The purpose of this paper is to model the multi-criteria decision problem of identifying the most suitable facility locations for biogas plants under an integrated decision support methodology. Here the Geographical Information System (GIS) is used for measuring the attributes of the alternatives...... according to a given set of criteria. Measurements are taken in interval form, expressing the natural imprecision of common data, and the Fuzzy Weighted Overlap Dominance (FWOD) procedure is applied for aggregating and exploiting this kind of data, obtaining suitability degrees for every alternative...... suitable sites for building biogas plants. We show that the FWOD relevance-ranking procedure can also be successfully applied over the outcomes of different decision makers, in case a unique social solution is required to exist. The proposed methodology can be used under an integrated decision support...

Dynamics of microbial communities in an integrated ultrafiltration–reverse osmosis desalination pilot plant located at the Arabian Gulf

KAUST Repository

Hong, Pei-Ying

2015-08-27

This study demonstrated the use of high-throughput sequencing to assess the efficacy of an integrated ultrafiltration (UF)–reverse osmosis (RO) desalination pilot plant located at the Arabian Gulf, and to identify potential microbial-associated problems that may arise in this plant. When integrated into the desalination treatment system, the UF membranes were able to serve as a good pretreatment strategy to delay RO fouling by achieving up to 1.96-log removal of cells from the seawater. Consequently, the differential pressure of the RO membrane remained around 1 bar for the entire six-month study, suggesting no significant biofouling performance issue identified for this RO system. Examples of microbial populations effectively removed by the UF membranes from the feed waters included Nitrosoarchaeum limnia and phototrophic eukaryotes. Microbial-associated problems observed in this pilot plant included the presence of Pseudomonas spp. in coexistence with Desulfovibrio spp. These two bacterial populations can reduce sulfate and produce hydrogen sulfide, which would in turn cause corrosion problems or compromise membrane integrities. Chemical-enhanced backwashing (CEB) can be used as an effective strategy to minimize the associated microbial problems by removing bacterial populations including sulfate reducers from the UF membranes.

Dynamics of microbial communities in an integrated ultrafiltration–reverse osmosis desalination pilot plant located at the Arabian Gulf

KAUST Repository

Hong, Pei-Ying; Moosa, Nasir; Mink, Justine

2015-01-01

This study demonstrated the use of high-throughput sequencing to assess the efficacy of an integrated ultrafiltration (UF)–reverse osmosis (RO) desalination pilot plant located at the Arabian Gulf, and to identify potential microbial-associated problems that may arise in this plant. When integrated into the desalination treatment system, the UF membranes were able to serve as a good pretreatment strategy to delay RO fouling by achieving up to 1.96-log removal of cells from the seawater. Consequently, the differential pressure of the RO membrane remained around 1 bar for the entire six-month study, suggesting no significant biofouling performance issue identified for this RO system. Examples of microbial populations effectively removed by the UF membranes from the feed waters included Nitrosoarchaeum limnia and phototrophic eukaryotes. Microbial-associated problems observed in this pilot plant included the presence of Pseudomonas spp. in coexistence with Desulfovibrio spp. These two bacterial populations can reduce sulfate and produce hydrogen sulfide, which would in turn cause corrosion problems or compromise membrane integrities. Chemical-enhanced backwashing (CEB) can be used as an effective strategy to minimize the associated microbial problems by removing bacterial populations including sulfate reducers from the UF membranes.

Automated method for determining location and magnitude of leaks inside a PWR containment

International Nuclear Information System (INIS)

Cho, J.H.; Elia, F.A. Jr.

1986-01-01

Thermal-hydraulics analysis can be used to determine location and magnitude of leaks inside a pressurized water reactor (PWR) containment, as required by plant technical specifications. The major advantage of this detection method is that it minimizes radiation exposure of maintenance personnel because most of the leak detection process is performed from the control room outside the containment. In addition, such a program allows for the elimination of pipe whip restraints and jet impingement shields, eliminating costs for maintenance of these supports and shields in older plants and lowering construction costs for new plants. Previously, only simple single-node containment models were used for determining leakage magnitude. This paper presents a more sophisticated multinode approach for determining the magnitude and location. The resulting sensitivities to leak can be programmed into the plant's computer system. In this way, the plant's computer will be able to measure and locate leaks inside containment. The study concludes that dew point temperature (or relative humidity) is the most suitable parameter for locating a leak while flow rate to sump is the most suitable parameter for quantifying the leak

Vegetation resurvey is robust to plot location uncertainty

Science.gov (United States)

Kopecký, Martin; Macek, Martin

2017-01-01

Aim Resurveys of historical vegetation plots are increasingly used for the assessment of decadal changes in plant species diversity and composition. However, historical plots are usually relocated only approximately. This potentially inflates temporal changes and undermines results. Location Temperate deciduous forests in Central Europe. Methods To explore if robust conclusions can be drawn from resurvey studies despite location uncertainty, we compared temporal changes in species richness, frequency, composition and compositional heterogeneity between exactly and approximately relocated plots. We hypothesized that compositional changes should be lower and changes in species richness should be less variable on exactly relocated plots, because pseudo-turnover inflates temporal changes on approximately relocated plots. Results Temporal changes in species richness were not more variable and temporal changes in species composition and compositional heterogeneity were not higher on approximately relocated plots. Moreover, the frequency of individual species changed similarly on both plot types. Main conclusions The resurvey of historical vegetation plots is robust to uncertainty in original plot location and, when done properly, provides reliable evidence of decadal changes in plant communities. This provides important background for other resurvey studies and opens up the possibility for large-scale assessments of plant community change. PMID:28503083

Effects of Planting Locations on the Proximate Compositions of ...

African Journals Online (AJOL)

ADOWIE PERE

Ash, moisture, crude fat, crude fibre, carbohydrate and protein contents were determined according ... All fruits, vegetables, legumes (beans and peas), and the grains we eat ... isolate and quantify each proximate present in the plant material.

Optimal hub location in pipeline networks

Energy Technology Data Exchange (ETDEWEB)

Dott, D.R.; Wirasinghe, S.C.; Chakma, A. [Univ. of Calgary, Alberta (Canada)

1996-12-31

This paper discusses optimization strategies and techniques for the location of natural gas marketing hubs in the North American gas pipeline network. A hub is a facility at which inbound and outbound network links meet and freight is redirected towards their destinations. Common examples of hubs used in the gas pipeline industry include gas plants, interconnects and market centers. Characteristics of the gas pipeline industry which are relevant to the optimization of transportation costs using hubs are presented. Allocation techniques for solving location-allocation problems are discussed. An outline of the research in process by the authors in the field of optimal gas hub location concludes the paper.

A fuzzy approach to a multiple criteria and geographical information system for decision support on suitable locations for biogas plants

DEFF Research Database (Denmark)

Franco de los Rios, Camilo Andres; Bojesen, Mikkel; Hougaard, Jens Leth

The purpose of this paper is to model the multi-criteria decision problem of identifying the most suitable facility locations for biogas plants under an integrated decision support methodology. Here the Geographical Information System (GIS) is used for measuring the attributes of the alternatives...... according to a given set of criteria. Measurements are taken in interval form, expressing the natural imprecision of common data, and the Fuzzy Weighted Overlap Dominance (FWOD) procedure is applied for aggregating and exploiting this kind of data, obtaining suitability degrees for every alternative....... The estimation of criteria weights, which is necessary for applying the FWOD procedure, is done by means of the Analytical Hierarchy Process (AHP), such that a combined AHP-FWOD methodology allows identifying the more suitable sites for building biogas plants. We show that the FWOD relevance-ranking procedure...

Simultaneous nitrification, denitrification and phosphorus removal (SNDPR) in a full-scale water reclamation plant located in warm climate.

Science.gov (United States)

Yang, Qin; Shen, Nan; Lee, Zarraz M-P; Xu, Guangjing; Cao, Yeshi; Kwok, Beehong; Lay, Winson; Liu, Yu; Zhou, Yan

The combination of simultaneous nitrification-denitrification (SND) with enhanced biological phosphorus removal (EBPR) provides a more efficient and economically viable option for nutrient removal from municipal wastewater compared to conventional two-step nitrification-denitrification. This study analyzed the nutrients (N and P) profiles in a full-scale municipal wastewater reclamation plant (WRP) located in the tropical region, in which more than 90% of nitrogen was removed. Interestingly, average SND efficiency in aerobic zones was found to be up to 50%, whereas phosphorus profile displayed a clear cyclic release and uptake pattern with a phosphorus removal efficiency of up to 76%. The capability of sludge to perform SND and EBPR was further confirmed through a series of batch experiments. Microbial analysis revealed the presence of Accumulibacter and Tetrasphaera phosphate accumulating organisms in the plant, while few glycogen accumulating organisms (GAO) was observed. This study showed the significant occurrence of combined SND and EBPR, known as simultaneous nitrification, denitrification and phosphorus removal (SNDPR), in the studied WRP under warm climate. The possible causes behind the observed SNDPR were also discussed.

Integrated Nuclear Recycle Plant

International Nuclear Information System (INIS)

Patodi, Anuj; Parashar, Abhishek; Samadhiya, Akshay K.; Ray, Saheli; Dey, Mitun; Singh, K.K.

2017-01-01

Nuclear Recycle Board (NRB), Tarapur proposes to set up an 'Integrated Nuclear Recycle Plant' at Tarapur. This will be located in the premises of BARC facilities. The project location is at coastal town of Tarapur, 130 Km north of Mumbai. Project area cover of INRP is around 80 hectares. The plant will be designed to process spent fuel received from Pressurized Heavy Water Reactors (PHWRs). This is the first large scale integrated plant of the country. INRP will process spent fuel obtained from indigenous nuclear power plants and perform left over nuclear waste disposal

Compilation and comparison of test-hole location surveys in the vicinity of the Waste Isolation Pilot Plant site

International Nuclear Information System (INIS)

Gonzales, M.M.

1989-02-01

Between 1976 and 1988, many surveys were performed related to the Waste Isolation Pilot Plant and its geologic and hydrologic test holes, which are part of the hydrogeologic-characterization program. Among these surveys were two First-Order, Class I vertical surveys, a satellite survey, and a number of township-range surveys. An overview of the basic function, history, and methodology of each survey type is provided in this report along with a review and comparison of the two major test-hole surveys. Elevation and location data for 96 test holes and 4 shafts are also included. The comparison of the satellite survey to the township-range surveys showed that the latter have the following advantages: their data are more complete; their elevation data are more accurate; and their techniques can be used for surveying new wells, keeping the data set consistent. Therefore, the final township-range surveys were selected as the best source of elevation and location data to use in the WIPP hydrology program. 17 refs., 5 figs., 10 tabs

Ethno-Botanical Survey Of Medicinal Plants In The Plant Genetic ...

African Journals Online (AJOL)

The ethno-botanical uses and mode of administration of twenty-nine medicinal plants found in the arboretum of the Plant Genetic Resource Centre located at Bunso in the Eastern region of Ghana against some disease conditions are hereby documented. Key words: Ethnobotany, medicinal plants, arboretum, Ghana. Nig.

LNG plant combined with power plant

Energy Technology Data Exchange (ETDEWEB)

Aoki, I; Kikkawa, Y [Chiyoda Chemical Engineering and Construction Co. Ltd., Tokyo (Japan)

1997-06-01

The LNG plant consumers a lot of power of natural gas cooling and liquefaction. In some LNG plant location, a rapid growth of electric power demand is expected due to the modernization of area and/or the country. The electric power demand will have a peak in day time and low consumption in night time, while the power demand of the LNG plant is almost constant due to its nature. Combining the LNG plant with power plant will contribute an improvement the thermal efficiency of the power plant by keeping higher average load of the power plant, which will lead to a reduction of electrical power generation cost. The sweet fuel gas to the power plant can be extracted from the LNG plant, which will be favorable from view point of clean air of the area. (Author). 5 figs.

LNG plant combined with power plant

International Nuclear Information System (INIS)

Aoki, I.; Kikkawa, Y.

1997-01-01

The LNG plant consumers a lot of power of natural gas cooling and liquefaction. In some LNG plant location, a rapid growth of electric power demand is expected due to the modernization of area and/or the country. The electric power demand will have a peak in day time and low consumption in night time, while the power demand of the LNG plant is almost constant due to its nature. Combining the LNG plant with power plant will contribute an improvement the thermal efficiency of the power plant by keeping higher average load of the power plant, which will lead to a reduction of electrical power generation cost. The sweet fuel gas to the power plant can be extracted from the LNG plant, which will be favorable from view point of clean air of the area. (Author). 5 figs

Location and sizing of a plant stack: Design study using CFD

International Nuclear Information System (INIS)

Petrangeli, Gianni

2011-01-01

Highlights: → The paper is a test of applicability of CFD Codes to a nuclear plant stack. → Six cases are studied and comparison is made with common methods. → A comparison with field test data is made. → The study shows that CFD Codes are adequate even in presence of complicated building arrangements. - Abstract: The effect of the presence of a stack on the ground level concentration of emissions near the plant is to significantly decrease the concentrations (in practical cases of interest, by a factor of 5-10), while the presence of nearby plant buildings is to partly eliminate this beneficial effect due to the effect of the building wake. The author of this paper believes that the practical methods currently used for the evaluation of ground concentrations in these cases deserve some improvement. One line of development here suggested is the use of Computer Fluid Dynamics (CFD) codes. The author believes that presently available Code Packages in this field are sufficiently accurate. A number of case studies are presented in this paper, with the aim of encouraging the use of these rather simple methods of study. Moreover, a comparison of calculation results with a field test results confirms also the quantitative reliability of the calculation method here proposed. The main conclusions of this exercise could be the following: -The use of CFD Computer Codes seems suitable for atmospheric dispersion calculations of interest to the nuclear plant designer and safety analyst; in particular, for design studies aimed at the definition of nuclear plant and stack arrangements, the result of this exercise seem to indicate that the methods here used are completely suitable for the comparison of various solutions. -The use of CFD codes may avoid wrong decisions, like the elimination of a stack in the design of a nuclear plant; excessive and detrimental over-conservatism can also be avoided. -When adequate guidance is provided, as this paper attempts to do (), the CFD

Experimental plant for sludge composting. Plant experimental de compostaje de lodos

Energy Technology Data Exchange (ETDEWEB)

Cadenas, A.; Caellas, N.; Amengual, A.; Calafact, J.

1993-01-01

Results and expertise collected during the first year of exploitation of a compost experimental plant located in Mallorca (Spain): The plant is treating sludge from the biological treatment plant of water at the town of Felanitx and the compost produced is used in agriculture. (Author)

Plant-mPLoc: a top-down strategy to augment the power for predicting plant protein subcellular localization.

Directory of Open Access Journals (Sweden)

Kuo-Chen Chou

Full Text Available One of the fundamental goals in proteomics and cell biology is to identify the functions of proteins in various cellular organelles and pathways. Information of subcellular locations of proteins can provide useful insights for revealing their functions and understanding how they interact with each other in cellular network systems. Most of the existing methods in predicting plant protein subcellular localization can only cover three or four location sites, and none of them can be used to deal with multiplex plant proteins that can simultaneously exist at two, or move between, two or more different location sits. Actually, such multiplex proteins might have special biological functions worthy of particular notice. The present study was devoted to improve the existing plant protein subcellular location predictors from the aforementioned two aspects. A new predictor called "Plant-mPLoc" is developed by integrating the gene ontology information, functional domain information, and sequential evolutionary information through three different modes of pseudo amino acid composition. It can be used to identify plant proteins among the following 12 location sites: (1 cell membrane, (2 cell wall, (3 chloroplast, (4 cytoplasm, (5 endoplasmic reticulum, (6 extracellular, (7 Golgi apparatus, (8 mitochondrion, (9 nucleus, (10 peroxisome, (11 plastid, and (12 vacuole. Compared with the existing methods for predicting plant protein subcellular localization, the new predictor is much more powerful and flexible. Particularly, it also has the capacity to deal with multiple-location proteins, which is beyond the reach of any existing predictors specialized for identifying plant protein subcellular localization. As a user-friendly web-server, Plant-mPLoc is freely accessible at http://www.csbio.sjtu.edu.cn/bioinf/plant-multi/. Moreover, for the convenience of the vast majority of experimental scientists, a step-by-step guide is provided on how to use the web-server to

Location matters: The impact of renewable power on transmission congestion and emissions

International Nuclear Information System (INIS)

Hitaj, Claudia

2015-01-01

Many governments offer subsidies for renewable power to reduce greenhouse gas emissions in the power sector. However, most support schemes for renewable power do not take into account that emissions depend on the location of renewable and conventional power plants within an electricity grid. I simulate optimal power flow in a test grid when 4 renewable power plants connect to the grid across 24 potential sites, amounting to over 10,000 configurations. Each configuration is associated with different levels of emissions and renewable power output. I find that emission reductions vary by a factor of 7 and that curtailment due to transmission congestion is more likely when renewable power plants are concentrated in an area of the grid with low demand. Large cost savings could be obtained by allowing subsidies for renewable power to vary across locations according to abatement potential or by replacing subsidies with a price on emissions. - Highlights: • Analyze the impact of renewable power plant location on congestion and emissions. • Simulate optimal power flow in a test grid for over 10,000 configurations. • Determine that emission reductions vary by a factor of 7. • Find that renewable power is curtailed due to transmission congestion. • Pricing emissions is most efficient since abatement potential varies across locations.

Location of Farmers Warehouse at Adaklu Traditional Area, Volta Region, Ghana

Directory of Open Access Journals (Sweden)

Vincent Tulasi

2016-01-01

Full Text Available Postharvest loss is one major problem farmers in Adaklu Traditional Area that most Ghanaian farmers face. As a result, many farmers wallow in abject poverty. Warehouses are important facilities that help to reduce postharvest loss. In this research, Beresnev pseudo-Boolean Simple Plant Location Problem (SPLP model is used to locate a warehouse at Adaklu Traditional Area, Volta Region, Ghana. This model was used because it gives a straightforward computation and produces no iteration as compared with other models. The SPLP is a problem of selecting a site from candidate sites to locate a plant so that customers can be supplied from the plant at a minimum cost. The model is made up of fixed cost and transportation cost. Location index ordering matrix was developed from the transportation cost matrix and we used it with the fixed cost and differences between variable costs to formulate the Beresnev function. Linear term developed from the function which was partial is pegged to obtain a complete solution. Of the 14 notable communities considered, Adaklu Waya is found most suitable for the setting of the warehouse. The total cost involved is Gh₵ 78,180.00.

MICROGRIDS: THE AGRIA TEST LOCATION

Directory of Open Access Journals (Sweden)

Aleksandra Krkoleva

2010-01-01

Full Text Available The paper presents the pilot Microgrid in Macedonia, developed within the framework of the MOREMICROGRIDS (EU EP6 projecet, contract No. SES6-019864 project. This Microgrid is the first of its kind being developed in the Western Balkan region and serves as pilot site for introduction and examination of the Microgrids concept in non European Union conditions. The test network consists of a part of the low voltage grid, located on a pig farm. The main electricity source for the Microgrid is a small biogas plant, which uses the biogas produced by a waste water treatment process. The paper addresses the Microgrid design, development of test scenarios and test results from the pilot location.

Expression of endogenous proteins in maize hybrids in a multi-location field trial in India.

Science.gov (United States)

Gutha, Linga R; Purushottam, Divakar; Veeramachaneni, Aruna; Tigulla, Sarita; Kodappully, Vikas; Enjala, Chandana; Rajput, Hitendrasinh; Anderson, Jennifer; Hong, Bonnie; Schmidt, Jean; Bagga, Shveta

2018-05-17

Genetically modified (GM) crops undergo large scale multi-location field trials to characterize agronomics, composition, and the concentration of newly expressed protein(s) [herein referred to as transgenic protein(s)]. The concentration of transgenic proteins in different plant tissues and across the developmental stages of the plant is considered in the safety assessment of GM crops. Reference or housekeeping proteins are expected to maintain a relatively stable expression pattern in healthy plants given their role in cellular functions. Understanding the effects of genotype, growth stage and location on the concentration of endogenous housekeeping proteins may provide insight into the contribution these factors could have on transgenic protein concentrations in GM crops. The concentrations of three endogenous proteins (actin, elongation factor 1-alpha, and glyceraldehyde 3-phosphate dehydrogenase) were measured in several different maize hybrids grown across multiple field locations over 2 years. Leaf samples were collected from healthy plants at three developmental stages across the growing seasons, and protein concentrations were quantified by indirect enzyme-linked immunosorbent assay (ELISA) for each protein. In general, the concentrations of these three endogenous proteins were relatively consistent across hybrid backgrounds, when compared within one growth stage and location (2-26%CV), whereas the concentrations of proteins in the same hybrid and growth stage across different locations were more variable (12-64%CV). In general, the protein concentrations in 2013 and 2014 show similar trends in variability. Some degree of variability in protein concentrations should be expected for both transgenic and endogenous plant-expressed proteins. In the case of GM crops, the potential variation in protein concentrations due to location effects is captured in the current model of multi-location field testing.

Meteorological monitoring Program in the location to the Juragua Nuclear Power Plant

International Nuclear Information System (INIS)

Linares Gonzalez, M.E.; Ramos Biltres, E.O.; Prendes Alonso, M.

1998-01-01

The objective gives the work it is to present the meteorological Monitoring program in the Juragua nuclear power plant, which you makes according to the standards settled down by the OIEA, the standards give the World meteorological organization and the demands to the content and elaboration gives the Nuclear Power Plant security documents DTN-1.03.91

Potency of Micro Hydro Power Plant Development Use of Kelampuak River Flow Located in Tamblang Village – Buleleng

Directory of Open Access Journals (Sweden)

Dewa Ngakan Ketut Putra Negara

2012-11-01

Full Text Available Need of electrical energy is increasing along with people population and economic growth. According to PLN data, Bali Province’s electrical consumption is predicted growth 5,6% in average every year. Until year 2007, electrical condition in Bali is categorized critical. If Power Plat in Bali, PLTG Gilimanuk that has power 130 MW is out of system, affecting Bali’s electrical back up is minus. Consecuenlly, it will be extinguishing if there is not adding power plan or new energy supply. This problem needs to be anticipated by use of thermal energy program such as coal, gas and geothermal and use of alternative energy such as solar, wind and ocean energies. Regency of Buleleng is one of Regency in Bali having potency of renewable energy development especially water resource. It has some rivers that have potency to be developed as a Micro Hydro Power Plant (PLTMH. One of them is Kelampuak River which is located in Tamblang Village. As a first step in developing of Micro Hydro Power Plant, it needs to be known water debit and head of the river. For that reason, it needs to be investigated debit and head of Kelampuak River so that it can be predicted the power can be generated.

Load flow analysis for determining the location of NPP power distribution in West Kalimantan

International Nuclear Information System (INIS)

Citra Candranurani; Rizki Finnansyah Setya Budi; Sahala M Lumbanraja

2015-01-01

Electricity crisis condition happened in West Kalimantan (Kalbar) as a result of power plant capacity almost equal to the peak load. The system will experience a shortfall if there are plants that not operating and do not have reserve. The policy of electricity planning until 2022 is replacing diesel power plant with steam power plant. For long-term planning is required the role of new and renewable energy in order to reduce dependency on fossil fuel consumption, such as NPP utilization. The purpose of this study was to determine the optimum location of the NPP power distribution in order to prepare electricity infrastructure. Load flow calculation in this study using ETAP 12.5 software. NPP is planned to supply base load, so the optimum capacity factor is above 80 %. The result show that there are three location where NPP can generate over 80 % of its capacity, namely: Mempawah Substation, Singkawang Substation, and Sambas Substation. The most optimum located in Mempawah Substation with capacity factor 83.5 %. The location of the three Substation are onshore and in line with one requirement for NPP construction, namely: the availability of cooling water. (author)

Location, location, location: Extracting location value from house prices

OpenAIRE

Kolbe, Jens; Schulz, Rainer; Wersing, Martin; Werwatz, Axel

2012-01-01

The price for a single-family house depends both on the characteristics of the building and on its location. We propose a novel semiparametric method to extract location values from house prices. After splitting house prices into building and land components, location values are estimated with adaptive weight smoothing. The adaptive estimator requires neither strong smoothness assumptions nor local symmetry. We apply the method to house transactions from Berlin, Germany. The estimated surface...

Decision support system for the optimal location of electrical and electronic waste treatment plants: A case study in Greece

International Nuclear Information System (INIS)

Achillas, Ch.; Vlachokostas, Ch.; Moussiopoulos, N.; Banias, G.

2010-01-01

Environmentally sound end-of-life management of Electrical and Electronic Equipment has been realised as a top priority issue internationally, both due to the waste stream's continuously increasing quantities, as well as its content in valuable and also hazardous materials. In an effort to manage Waste Electrical and Electronic Equipment (WEEE), adequate infrastructure in treatment and recycling facilities is considered a prerequisite. A critical number of such plants are mandatory to be installed in order: (i) to accommodate legislative needs, (ii) decrease transportation cost, and (iii) expand reverse logistics network and cover more areas. However, WEEE recycling infrastructures require high expenditures and therefore the decision maker need to be most precautious. In this context, special care should be given on the viability of infrastructure which is heavily dependent on facilities' location. To this end, a methodology aiming towards optimal location of Units of Treatment and Recycling is developed, taking into consideration economical together with social criteria, in an effort to interlace local acceptance and financial viability. For the decision support system's needs, ELECTRE III is adopted as a multicriteria analysis technique. The methodology's applicability is demonstrated with a real-world case study in Greece.

Next Generation Nuclear Plant Project Evaluation of Siting a HTGR Co-generation Plant on an Operating Commercial Nuclear Power Plant Site

International Nuclear Information System (INIS)

Demick, L.E.

2011-01-01

This paper summarizes an evaluation by the Idaho National Laboratory (INL) Next Generation Nuclear Plant (NGNP) Project of siting a High Temperature Gas-cooled Reactor (HTGR) plant on an existing nuclear plant site that is located in an area of significant industrial activity. This is a co-generation application in which the HTGR Plant will be supplying steam and electricity to one or more of the nearby industrial plants.

Next Generation Nuclear Plant Project Evaluation of Siting a HTGR Co-generation Plant on an Operating Commercial Nuclear Power Plant Site

Energy Technology Data Exchange (ETDEWEB)

L.E. Demick

2011-10-01

This paper summarizes an evaluation by the Idaho National Laboratory (INL) Next Generation Nuclear Plant (NGNP) Project of siting a High Temperature Gas-cooled Reactor (HTGR) plant on an existing nuclear plant site that is located in an area of significant industrial activity. This is a co-generation application in which the HTGR Plant will be supplying steam and electricity to one or more of the nearby industrial plants.

Grass plants crop water consumption model in urban parks located ...

African Journals Online (AJOL)

use

2011-12-14

Dec 14, 2011 ... parks located in three different climate zones of Turkey. E. Bayramoğlu1* and Ö. .... Many factors influence evapotranspiration. The most important ... sky is not covered in clouds) and daytime hours until sunset increase, both ...

Methodology to identify the location of shoals of fish downstream from hydroelectric power plant; Metodologia para identificar a locacao de cardumes de peixes a jusante de UHE

Energy Technology Data Exchange (ETDEWEB)

Martinez, C.B.; Viana, E.M.F.; Faria, M.T.C. de [Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil). Centro de Pesquisas Hidraulicas e Recursos Hidricos], Emails: martinez@cce.ufmg.br, ednamariafaria@ufmg.br, mtcdf@uol.com.br

2009-07-01

The location identification of fish shoals at the downstream of an hydroelectric power plants is a task of importance especially when one takes into account the need to identify possible locations for the deployment of fish transportation mechanism. This paper presents a methodology based on the use of reduced models, which will be operated during the biological testing, under flow and conditions similar to the field where will be included shoals of fish. These groups will be observed during a period of time under varying conditions of discharge of hydraulic turbines. At the end of this observation it can be identified preferential location areas of fish shoals that will be evaluated later in order to install transposition systems in the place.

Birds exploit herbivore-induced plant volatiles to locate herbivorous prey

NARCIS (Netherlands)

Amo, L.; Jansen, J.J.; Dam, van N.M.; Dicke, M.; Visser, M.E.

2013-01-01

Arthropod herbivory induces plant volatiles that can be used by natural enemies of the herbivores to find their prey. This has been studied mainly for arthropods that prey upon or parasitise herbivorous arthropods but rarely for insectivorous birds, one of the main groups of predators of herbivorous

Japanese national reference reprocessing plant

International Nuclear Information System (INIS)

1978-08-01

This paper gives a general description of the proposed Japanese national reprocessing plant and of the design philosophy. The plant is in most respects similar to the base case reprocessing plant, with an annual throughput of 100-1500 tU. The plant would be co-located with a fuel fabrication facility

25 CFR 214.28 - Location of sites for mines and buildings.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Location of sites for mines and buildings. 214.28 Section... and buildings. In event of disagreement between two or more mineral lessees regarding sites for the location of wells, mines, buildings, plants, etc., the same shall be determined by the superintendent after...

Detection and Toxicity Evaluation of Pyrrolizidine Alkaloids in Medicinal Plants Gynura bicolor and Gynura divaricata Collected from Different Chinese Locations.

Science.gov (United States)

Chen, Jian; Lü, Han; Fang, Lian-Xiang; Li, Wei-Lin; Verschaeve, Luc; Wang, Zheng-Tao; De Kimpe, Norbert; Mangelinckx, Sven

2017-02-01

Two edible plants in Southeast Asia, Gynura bicolor and G. divaricata, are not only known to be nutritive but also useful as medicinal herbs. Previous phytochemical investigation of Gynura species showed the presence of hepatotoxic pyrrolizidine alkaloids (PAs), indicating the toxic risk of using these two plants. The present study was designed to analyze the distribution of PA components and tried to evaluate the preliminary toxicity of these two Gynura species. Eight samples of G. bicolor and G. divaricata from five different Chinese locations were collected and their specific PAs were qualitatively characterized by applying an UPLC/MS/MS spectrometry method. Using a pre-column derivatization HPLC method, the total retronecine ester-type PAs in their alkaloids extracts were quantitatively estimated as well. Finally, their genotoxicity was investigated with an effective high-throughput screening method referred to as Vitotox™ test and their potential cytotoxicity was tested on HepG2 cells. It was found that different types of PAs were widely present in Gynura species collected from south of China. Among them, no significant genotoxic effects were detected with serial concentrations through the present in vitro assay. However, the cytotoxicity assay of Gynura plants collected from Jiangsu displayed weak activity at the concentration of 100 mg/ml. It is important to note that this research validates in part the indication that the use of Gynura species requires caution. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Effect of oil spills on coastal power plants, refineries, and desalination plants

International Nuclear Information System (INIS)

Kiefer, C.; Mussali, Y.

1992-01-01

Major oil spills such as those experienced in the Gulf War, in Alaska, and in the Gulf of Mexico have raised concern for the protection of coastal facilities which use seawater for cooling or process purposes such as power stations, refineries, and desalination plants. Because of the availability of large quantities of cooling water, many power stations and refineries are located along the coastline in the United States and throughout the world. In addition, many countries in the Middle East, the Caribbean, and other areas of the world depend on desalination plants located along the coast for the vital supply of drinking water. The objective of this paper is to determine the levels of oil contamination which will adversely affect plant performance or result in damage to specific plant equipment such as condensers, heat exchangers, pumps, screens, water treatment equipment, and other vital water handling mechanisms

Effects of plant phenology and vertical height on accuracy of radio-telemetry locations

Science.gov (United States)

Grovenburg, Troy W.; Jacques, Christopher N.; Klaver, Robert W.; DePerno, Christopher S.; Lehman, Chad P.; Brinkman, Todd J.; Robling, Kevin A.; Rupp, Susan P.; Jenks, Jonathan A.

2013-01-01

The use of very high frequency (VHF) radio-telemetry remains wide-spread in studies of wildlife ecology and management. However, few studies have evaluated the influence of vegetative obstruction on accuracy in differing habitats with varying transmitter types and heights. Using adult and fawn collars at varying heights above the ground (0, 33, 66 and 100 cm) to simulate activities (bedded, feeding and standing) and ages (neonate, juvenile and adult) of deer Odocoileus spp., we collected 5,767 bearings and estimated 1,424 locations (28-30 for each of 48 subsamples) in three habitat types (pasture, grassland and forest), during two stages of vegetative growth (spring and late summer). Bearing error was approximately twice as large at a distance of 900 m for fawn (9.9°) than for adult deer collars (4.9°). Of 12 models developed to explain the variation in location error, the analysis of covariance model (HT*D + C*D + HT*TBA + C*TBA) containing interactions of height of collar above ground (HT), collar type (C), vertical height of understory vegetation (D) and tree basal area (TBA) was the best model (wi = 0.92) and explained ∼ 71% of the variation in location error. Location error was greater for both collar types at 0 and 33 cm above the ground compared to 66 and 100 cm above the ground; however, location error was less for adult than fawn collars. Vegetation metrics influenced location error, which increased with greater vertical height of understory vegetation and tree basal area. Further, interaction of vegetation metrics and categorical variables indicated significant effects on location error. Our results indicate that researchers need to consider study objectives, life history of the study animal, signal strength of collar (collar type), distance from transmitter to receiver, topographical changes in elevation, habitat composition and season when designing telemetry protocols. Bearing distances in forested habitat should be decreased (approximately 23

Finding the Subcellular Location of Barley, Wheat, Rice and Maize Proteins: The Compendium of Crop Proteins with Annotated Locations (cropPAL).

Science.gov (United States)

Hooper, Cornelia M; Castleden, Ian R; Aryamanesh, Nader; Jacoby, Richard P; Millar, A Harvey

2016-01-01

Barley, wheat, rice and maize provide the bulk of human nutrition and have extensive industrial use as agricultural products. The genomes of these crops each contains >40,000 genes encoding proteins; however, the major genome databases for these species lack annotation information of protein subcellular location for >80% of these gene products. We address this gap, by constructing the compendium of crop protein subcellular locations called crop Proteins with Annotated Locations (cropPAL). Subcellular location is most commonly determined by fluorescent protein tagging of live cells or mass spectrometry detection in subcellular purifications, but can also be predicted from amino acid sequence or protein expression patterns. The cropPAL database collates 556 published studies, from >300 research institutes in >30 countries that have been previously published, as well as compiling eight pre-computed subcellular predictions for all Hordeum vulgare, Triticum aestivum, Oryza sativa and Zea mays protein sequences. The data collection including metadata for proteins and published studies can be accessed through a search portal http://crop-PAL.org. The subcellular localization information housed in cropPAL helps to depict plant cells as compartmentalized protein networks that can be investigated for improving crop yield and quality, and developing new biotechnological solutions to agricultural challenges. © The Author 2015. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Aquatic Plant Control Research Program

National Research Council Canada - National Science Library

Cofrancesco, Alfred

1998-01-01

.... This search for natural plant enemies (insects and fungal pathogens) has led researchers to the native ranges of noxious aquatic plants, located throughout the continents of Africa, Asia, Europe, and Australia...

Chemicals on plant surfaces as a heretofore unrecognized, but ecologically informative, class for investigations into plant defence.

Science.gov (United States)

LoPresti, Eric F

2016-11-01

Plants produce and utilize a great diversity of chemicals for a variety of physiological and ecological purposes. Many of these chemicals defend plants against herbivores, pathogens and competitors. The location of these chemicals varies within the plant, some are located entirely within plant tissues, others exist in the air- (or water-) space around plants, and still others are secreted onto plant surfaces as exudates. I argue herein that the location of a given defensive chemical has profound implications for its ecological function; specifically, I focus on the characteristics of chemical defences secreted onto plant surfaces. Drawing from a broad literature encompassing ecology, evolution, taxonomy and physiology, I found that these external chemical defences (ECDs) are common and widespread in plants and algae; hundreds of examples have been detailed, yet they are not delineated as a separate class from internal chemical defences (ICDs). I propose a novel typology for ECDs and, using existing literature, explore the ecological consequences of the hypothesized unique characteristics of ECDs. The axis of total or proportional investment in ECDs versus ICDs should be considered as one axis of investment by a plant, in the same way as quantitative versus qualitative chemical defences or induced versus constitutive defences is considered. The ease of manipulating ECDs in many plant systems presents a powerful tool to help test plant defence theory (e.g. optimal defence). The framework outlined here integrates various disciplines of botany and ecology and suggests a need for further examinations of exudates in a variety of contexts, as well as recognition of the effects of within-plant localization of defences. © 2015 Cambridge Philosophical Society.

An Integrated Decision-Making Model for the Location of a PV Solar Plant

Directory of Open Access Journals (Sweden)

Amy H. I. Lee

2015-09-01

Full Text Available Due to the increasing demand for electricity, the depletion of fossil fuels and the increase in environmental consciousness, generating power from renewable energy resources has become necessary. How to select the most appropriate site is a critical and foremost decision that must be made when setting up a renewable energy plant. This research proposes a two-stage framework for evaluating the suitability of renewable energy plant site alternatives. In the first stage, a fuzzy analytic hierarchy process (FAHP is adopted to set the assurance region (AR of the quantitative factors, and the AR is incorporated into data envelopment analysis (DEA to assess the efficiencies of plant site candidates. A few sites are selected for further analysis. In the second stage, experts are invited to evaluate the qualitative characteristics of the selected sites, and FAHP is used to calculate the priorities of these sites. Solar energy is one of the most promising renewable energy sources, because of its abundance, inexhaustibility, safety and cleanliness. Based on the proposed integrated decision-making model, a case study for selecting the most appropriate photovoltaic (PV solar plant site is examined.

7 CFR 1131.7 - Pool plant.

Science.gov (United States)

2010-01-01

... operator in Class I or Class II products, and must be located in a pricing zone providing the same or lower... plant (excluding concentrated milk received from another plant by agreement for other than Class I use... the plant (excluding concentrated milk received from another plant by agreement for other than Class I...

Location-Allocation model for food industrial using fuzzy criteria: A case study of dairy industry

Directory of Open Access Journals (Sweden)

Zahra Esfandiyari

2011-07-01

Full Text Available A good facility layout plays an important role on increasing the profitability of a production unit. A good location needs to meet different criteria such as the distance between the plants and the places to reach raw materials, customers, etc. In this paper, we proposed a multi criteria decision making problem to locate a suitable dairy plant. We assume that all factors influencing the plant involves uncertainty and proposed fuzzy numbers to handle the uncertainty associated with all input parameters. We apply the method for a real-world case study of dairy production unit and analyze the results of our proposed model.

Environmental impact of site location on macro- and microelements ...

African Journals Online (AJOL)

Human activities cause specific impact on the enveronment, which also could been monitored by mineral contents in the soil and in the plants. Two different caracteristic locations had been selected for the experiments: anthropogenic-Ada Huja contamineted industrial zone and non anthropogenic- Topcider park area.

Utilizing NASA EOS to Assist in Determining Suitable Planting Locations for Bottomland Hardwood Trees in St. Bernard Parish, Louisiana

Science.gov (United States)

Reahard, R. R.; Arguelles, M.; Ewing, M.; Kelly, C.; Strong, E.

2012-12-01

St. Bernard Parish, located in southeast Louisiana, is rapidly losing coastal forests and wetlands due to a variety of natural and anthropogenic disturbances (e.g. subsidence, saltwater intrusion, low sedimentation, nutrient deficiency, herbivory, canal dredging, levee construction, spread of invasive species, etc.). After Hurricane Katrina severely impacted the area in 2005, multiple Non-Governmental Organizations (NGOs) have focused not only on rebuilding destroyed dwellings, but on rebuilding the ecosystems that once protected the citizens of St. Bernard Parish. Volunteer groups, NGOs, and government entities often work separately and independently of each other and use different sets of information to choose the best planting sites for restoring coastal forests. Using NASA Earth Observing Systems (EOS), Natural Resource Conservation Service (NRCS) soil surveys, and ancillary road and canal data in conjunction with ground truthing, the team created maps of optimal planting sites for several species of bottomland hardwood trees to aid in unifying these organizations, who share a common goal, under one plan. The methodology for this project created a comprehensive Geographic Information System (GIS) to help identify suitable planting sites in St. Bernard Parish. This included supplementing existing elevation data using Digital Elevation Models derived from LIDAR data, and determining existing land cover in the study area from classified Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) imagery. Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data from a single low-altitude swath was used to assess the health of vegetation over an area near the Mississippi River Gulf Outlet Canal (MRGO) and Bayou La Loutre. Historic extent of coastal forests was also mapped using aerial photos collected between 1952 and 1956. The final products demonstrated yet another application of NASA EOS in the rebuilding and monitoring of coastal ecosystems in

China’s Nuclear Power Plants in Operation

Institute of Scientific and Technical Information of China (English)

无

2011-01-01

Qinshan Plant Phase I Located in Haiyan,Zhejiang Province,Qinshan Nuclear Power Plant Phase I is t he first 300-megawatt pressurized water reactor (PWR) nuclear power plant independently designed,constructed,operated and managed by China.The plant came into commercial operation in April 1994.

Toxic ornamental plants in Venezuela

Directory of Open Access Journals (Sweden)

Carlos Varela Romero

2017-01-01

Full Text Available The aim of this research was to contribute information on toxic ornamental plants in Venezuela. Information on taxonomy, common names, habit, origin, status, location, propagation and toxicology (part of the plant, effects was compiled from articles, books, catalogs, herbarium collections. A botanical analysis (taxonomy, common names, habit, origin, status, location, propagation and toxicology (part of the plant, effects was performed. The information about plant poisoning cases was requested to SIMET (Pharmacy faculty -UCV. Seventy-eight species were found in 34 families, the most important were: Apocynaceae (10 genera/12 species, Araceae (9/9, Euphorbiaceae (4/10 and Solanaceae (5/6. Genus Euphorbia was the most species rich. Most species were exotic species (79.5% and shrubs (32.1%. The entire plant (35 and latex (19 were the most toxic parts and the most frequent accidental ingestion (61.5%. Twenty cases were reported between 2009-2013, of which 80% were minors, female and urban areas. There is very little information published in Hispanic American countries

Planting and care of fine hardwood seedlings: Designing hardwood tree plantings for wildlife

Science.gov (United States)

Brian J. MacGowan

2003-01-01

Woody plants can be of value to many wildlife species. The species of tree or shrub, or the location, size, and shape of planting can all have an impact on wildlife. The purpose of this paper is to discuss the benefits of trees and shrubs for wildlife and how to design tree and shrub plantings for wildlife. Some of the practices may conflict with other management...

Location sites for nuclear power plants and the public drinking water supplies

International Nuclear Information System (INIS)

1987-05-01

This report presents the results of a study by the Dutch RIWA- Working Group Nuclear Power Plants, of the possible effects of a nuclear-reactor melt-down accident upon the drinking-water supply in the Netherlands which is dependent on surface waters. The aim of this report is to contribute to the 're-consideration with regard to siting of nuclear power plants' of the Dutch government. In the case of a nuclear-reactor melt-down accident in the Netherlands or directly adjacent countries, surface waters destined for drinking-water production may be contaminated severely. The amount of contamination depends, among other things, upon the distance, wind direction, dry as well as wet deposition and the features of the place yielding drinking water. From calculations of contamination of surface waters in the case of open- supply build up it appears that the derived norm of the radionuclide cocktail may be exceeded for a period of weeks up to several months or even years. There are reasons to draw the same conclusion for supply build up in the dunes by means of surface infiltration in the dunes. A melt-down accident can cause very severe contamination. Also here it can be stated that, in the case of a calamity in the Netherlands or directly adjacent countries, a norm transgression may occur for weeks up to years. In view of the risks which nuclear power plants can hold for the drinking-water supply which depends upon surface-waters as basis element. Severe objections should be made with respect to the siting of nuclear power plants in the Netherlands unless the occurrence of melt-down accidents could be excluded. 11 refs.; 4 figs.; 7 tabs

Local variation in conspecific plant density influences plant-soil feedback in a natural grassland

NARCIS (Netherlands)

Kos, M.; Veendrick, Johan; Bezemer, T.M.

2013-01-01

Several studies have argued that under field conditions plant–soil feedback may be related to the local density of a plant species, but plant–soil feedback is often studied by comparing conspecific and heterospecific soils or by using mixed soil samples collected from different locations and plant

Centralized manure digestion. Selection of locations and estimation of costs of large-scale manure storage application

International Nuclear Information System (INIS)

1995-03-01

A study to assess the possibilities and the consequences of the use of existing Dutch large scale manure silos at centralised anaerobic digestion plants (CAD-plants) for manure and energy-rich organic wastes is carried out. Reconstruction of these large scale manure silos into digesters for a CAD-plant is not self-evident due to the high height/diameter ratio of these silos and the extra investments that have to be made for additional facilities for roofing, insulation, mixing and heating. From the results of an inventory and selection of large scale manure silos with a storage capacity above 1,500 m 3 it appeared that there are 21 locations in The Netherlands that can be qualified for realisation of a CAD plant with a processing capacity of 100 m 3 biomass (80% manure, 20% additives) per day. These locations are found in particular at the 'shortage-areas' for manure fertilisation in the Dutch provinces Groningen and Drenthe. Three of these 21 locations with large scale silos are considered to be the most suitable for realisation of a large scale CAD-plant. The selection is based on an optimal scale for a CAD-plant of 300 m 3 material (80% manure, 20% additives) to be processed per day and the most suitable consuming markets for the biogas produced at the CAD-plant. The three locations are at Middelharnis, Veendam, and Klazinaveen. Applying the conditions as used in this study and accounting for all costs for transport of manure, additives and end-product including the costs for the storage facilities, a break-even operation might be realised at a minimum income for the additives of approximately 50 Dutch guilders per m 3 (including TAV). This income price is considerably lower than the prevailing costs for tipping or processing of organic wastes in The Netherlands. This study revealed that a break-even exploitation of a large scale CAD-plant for the processing of manure with energy-rich additives is possible. (Abstract Truncated)

Location, location, location

NARCIS (Netherlands)

Anderson, S.P.; Goeree, J.K.; Ramer, R.

1997-01-01

We analyze the canonical location-then-price duopoly game with general log- concave consumer densities. A unique pure-strategy equilibrium to the two-stage game exists if the density is not "too asymmetric" and not "too concave." These criteria are satisfied by many commonly used densities.

Concepts of plant health – reviewing and challenging the foundations of plant protection

OpenAIRE

Döring, Thomas; Pautasso, Marco; Finckh, Maria R.; Wolfe, Martin

2012-01-01

Plant health is a frequently used but ill-defined term. However, there is an extensive literature on general health definitions and health criteria in human medicine. Taking up ideas from these philosophical debates, concepts of plant health are reviewed and a framework developed to locate these concepts according to their position in several philosophical controversies. In particular, (i) the role of values in defining plant health in a naturalist versus a normativist approach; (ii) negative...

Environmental monitoring at the Savannah River Plant. Annual report, 1976

International Nuclear Information System (INIS)

Ashley, C.; Zeigler, C.C.

1978-03-01

The environmental monitoring program at the Savannah River Plant (SRP) provides reliable measurement of radioactive materials released at the source (approximately 40 locations) and present in the environment (approximately 500 locations). In recent years, water-quality testing and analysis have become an essential part of the environmental monitoring program. Aqueous discharges to plant streams are monitored for nonradioactive materials by chemical analyses of water sampled in flowing streams (approximately 25 locations). A brief discussion of plant releases to the environment and radioactive and nonradioactive materials detected in the environment are presented. The appendices contain data analysis and quality control information, sensitivities of laboratory analyses, tables of environmental sample analyses, and maps of sampling locations

Potential bioethanol feedstock availability around nine locations in the Republic of Ireland

International Nuclear Information System (INIS)

Deverell, R.; McDonnell, K.; Devlin, G.

2009-01-01

The Republic of Ireland, like many other countries is trying to diversify energy sources to counteract environmental, political and social concerns. Bioethanol from domestically grown agricultural crops is an indigenously produced alternative fuel that can potentially go towards meeting the goal of diversified energy supply. The Republic of Ireland's distribution of existing soils and agricultural land-uses limit arable crop land to around 10% of total agricultural area. Demand for land to produce arable crops is expected to decrease, which could open the opportunity for bioethanol production. Bioethanol production plants are required to be of a sufficient scale in order to compete economically with other fuel sources, it is important therefore to determine if enough land exists around potential ethanol plant locations to meet the potential demands for feedstock. This study determines, through the use of a developed GIS based model, the potential quantities of feedstock that is available in the hinterlands of nine locations in the Republic of Ireland. The results indicate that three locations can meet all its feedstock demands using indigenously grown sugarbeet, while only one location can meet its demands using a combination of indigenous wheat and straw as the two locally sourced feedstocks. (author)

75 FR 66802 - Calvert Cliffs Nuclear Power Plant, LLC; Calvert Cliffs Nuclear Power Plant, Unit Nos. 1 and 2...

Science.gov (United States)

2010-10-29

... Nuclear Power Plant, LLC; Calvert Cliffs Nuclear Power Plant, Unit Nos. 1 and 2; Notice of Withdrawal of...) has granted the request of Calvert Cliffs Nuclear Power Plant, LLC, the licensee, to withdraw its... for the Calvert Cliffs Nuclear Power Plant, Unit Nos. 1 and 2, located in Calvert County, MD. The...

Volatile chemical interaction between undamaged plants

OpenAIRE

Glinwood, Robert

2010-01-01

This chapter discusses whether plant chemical communication is a mechanism by which plant genetic diversity can affect the natural enemies of herbivores. Plant genetic diversity influences natural enemies, and these insects use volatile chemical cues to locate suitable habitats. However, the importance of chemical communication for these interactions has not been considered. In this chapter, the latest research on chemical communication between undamaged plants is reviewed. ...

Gamma dose mapping studies at various locations from bottled up activity in RCB of PFBR following CDA

International Nuclear Information System (INIS)

Baskar, S.; Rajagopal, V.; Indira, R.; Sunil Sunny, C.; Subbaiah, K.V.

2005-01-01

In the event of a Core Disruptive Accident (CDA), large amounts of radioactivity from the core gets released into the Reactor Containment Building (RCB) and bottled up. This acts as a huge volume source, which results in high gamma exposure to the plant personnel at various locations. The dose mapping at various locations in the nuclear island of PFBR under a CDA is essential for the following reasons: (1) To identify the high dose rate areas and locations which are to be avoided during emergency evacuation of plant personnel, (2) To provide suitable emergency exits and identify suitable assembly areas for plant personnel, (3) To provide a realistic estimate of the dose rates and cumulative doses to the essential plant personnel and (4) To provide necessary modifications in the design of the reactor at the design stage itself for minimizing exposure to the plant personnel. The RCB is made up of thick walls of concrete with large penetrations in the form of airlocks like Personnel Airlock (PAL), Material Airlock (MAL) and Emergency Airlock (EAL), to facilitate personnel and material movement, resulting in reduced shielding and higher dose rates. Computations of gamma dose rates have been performed using the point kernel code QADCG-GP at various locations around the RCB of a Prototype Fast Breeder Reactor (PFBR) by actual modeling of the RCB and the auxiliary buildings. The highest dose rates are seen in the vicinity of the airlocks, as expected. (author)

Plants attract parasitic wasps to defend themselves against insect pests by releasing hexenol.

Directory of Open Access Journals (Sweden)

Jianing Wei

2007-09-01

Full Text Available Plant volatiles play an important role in defending plants against insect attacks by attracting their natural enemies. For example, green leaf volatiles (GLVs and terpenoids emitted from herbivore-damaged plants were found to be important in the host location of parasitic wasps. However, evidence of the functional roles and mechanisms of these semio-chemicals from a system of multiple plants in prey location by the parasitoid is limited. Little is known about the potential evolutionary trends between herbivore-induced host plant volatiles and the host location of their parasitoids.The present study includes hierarchical cluster analyses of plant volatile profiles from seven families of host and non-host plants of pea leafminer, Liriomyza huidobrensis, and behavioral responses of a naive parasitic wasp, Opius dissitus, to some principal volatile compounds. Here we show that plants can effectively pull wasps, O. dissitus, towards them by releasing a universally induced compound, (Z-3-hexenol, and potentially keep these plants safe from parasitic assaults by leafminer pests, L. huidobrensis. Specifically, we found that volatile profiles from healthy plants revealed a partly phylogenetic signal, while the inducible compounds of the infested-plants did not result from the fact that the induced plant volatiles dominate most of the volatile blends of the host and non-host plants of the leafminer pests. We further show that the parasitoids are capable of distinguishing the damaged host plant from the non-host plant of the leafminers.Our results suggest that, as the most passive scenario of plant involvement, leafminers and mechanical damages evoke similar semio-chemicals. Using ubiquitous compounds, such as hexenol, for host location by general parasitoids could be an adaptation of the most conservative evolution of tritrophic interaction. Although for this, other compounds may be used to improve the precision of the host location by the parasitoids.

Environmental monitoring at the Savannah River Plant. Annual report, 1975

International Nuclear Information System (INIS)

Ashley, C.; Zeigler, C.C.

1975-01-01

The environmental monitoring program at the Savannah River Plant (SRP) provides reliable measurement of radioactive materials both released at the source (approximately 40 locations) and concentrated in the environment (approximately 500 locations). In recent years, water quality testing and analysis have become an essential part of the environmental monitoring program. Aqueous discharges to plant streams are monitored for nonradioactive materials by chemical analyses of water sampled in flowing streams (approximately 25 locations). A brief discussion of plant releases to the environment and radioactive and nonradioactive materials detected in the environment are presented in the following text, figures, and tables. The appendices contain an interpretation of data treatment, tables of results of environmental sample analyses, sensitivities of laboratory analyses, and maps of sampling locations

Preliminary design of the Carrisa Plains solar central receiver power plant. Volume II. Plant specifications

Energy Technology Data Exchange (ETDEWEB)

Price, R. E.

1983-12-31

The specifications and design criteria for all plant systems and subsystems used in developing the preliminary design of Carrisa Plains 30-MWe Solar Plant are contained in this volume. The specifications have been organized according to plant systems and levels. The levels are arranged in tiers. Starting at the top tier and proceeding down, the specification levels are the plant, system, subsystem, components, and fabrication. A tab number, listed in the index, has been assigned each document to facilitate document location.

Sustainable energy from biomass: Biomethane manufacturing plant location and distribution problem

International Nuclear Information System (INIS)

Wu, Bingqing; Sarker, Bhaba R.; Paudel, Krishna P.

2015-01-01

Highlights: • Optimal strategy to locate biogas reactor and allocating feedstock. • Nonlinear mixed integer programming problem structure. • Real world supply chain of biogas production system. • Considers construction cost, transportation and labor costs. • Novel heuristic improves efficiency to obtain optimal solution. - Abstract: As an environment-friendly and renewable energy source, biomethane plays a significant role in the supply of sustainable energy. To facilitate the decision-making process of where to build a biomethane production system (BMPS) and how to allocate the resources for the BMPS, this paper develops an analytical method to find the solutions to location and allocation problems by minimizing the supply chain cost of the BMPS. The BMPS consists of the local farms for providing feedstock, the hubs for collecting and storing feedstock from farms, and the reactors for producing biomethane from feedstock. A mixed integer nonlinear programming (MINLP) is introduced to model the supply chain by considering building, transportation, and labor costs. An alternative heuristic is proposed to obtain an optimal/sub-optimal solution from the MINLP. The validity of the proposed heuristic is proven by numerical examples that are abstracted from practical scenarios.

Examination advice of the location-independent Environmental-impact report and advice-direction guides for the location-dependent environmental-impact report concerning storage and processing of radioactive waste

International Nuclear Information System (INIS)

1986-01-01

This document is the examination advice made by the Provisional Committee for the environmental-impact reporting (VCmer) in view of the decision-making in behalf of which the location-independent environmental-impact report (MER) has been drawn up. Besides the examination by the VCmer of the location-independent MER in accordance with article 41z, part 1 and 2, this document covers an advice for direction guides for the, still to be drawn up, location-dependent MER on the storage and processing of radioactive wastes produced in the Netherlands, in accordance with article 41n, part 1 of the enactment m.e.r. The MER has been drawn up in behalf of the decision-making about location, design and construction of an aboveground, temporal storage of radioactive waste for the coming 50-100 years. In the MER two scenarios are distinguished: scenario 1 in fact reflects the actual situation in which, besides the amount of low- and medium-level radioactive waste, the high-level radioactive waste from the two nuclear power plants in the Netherlands have to be taken into account. Scenario 2 includes, besides the waste production of scenario 1, an extension with regard to the waste which would be produced in a 30-year operation time of a, still to be isntalled, nuclear power of 2000 MWe, to be increased up to 4000 MWe eventually. In this scenario finally about three quarter of the total volume of all radioactive waste would be produced by nuclear power plants. In that case emphasis will lay upon an installation which in particular has to be appropriate for a longtime, be it still temporary, storage of radioactive waste originating, largely, from the new nuclear power plant to be build in the Netherlands. (author)

Tracing disinfection byproducts in full-scale desalination plants

KAUST Repository

Le Roux, Julien; Nada, Nabil A.; Khan, Muhammad; Croue, Jean-Philippe

2015-01-01

-scale desalination plants. One thermal multi-stage flash distillation (MSF) plant and two reverse osmosis (RO) plants located on the Red Sea coast of Saudi Arabia. DBPs formed during the prechlorination step were efficiently removed along the treatment processes (MSF

Commissioning of the nuclear power plant

International Nuclear Information System (INIS)

Furtado, P.M.; Rolf, F.

1984-01-01

Nuclear Power Plant Angra 2, located at Itaorna Beach-Angra dos Reis is the first plant of the Brazilian-German Agreement to be commissioned. The Nuclear Power Plant is a pressurized water reactor rated at 3765 Mw thermal/1325 Mw electrical. For commissioning purpose the plant is divided into 110 systems. Plant commissioning objective is to demonstrate the safe and correct operation of each plan component, system and of the whole plant in agreement with design conditions, licensing requirements and contractual obligations. This work gives a description of plant commissioning objectives, activities their time sequence, and documentation. (Author) [pt

FLUES - A new monitoring system for leak detection and location

International Nuclear Information System (INIS)

Jax, P.; Streicher, V.

1995-01-01

A new Leakage Monitoring and Location System with high sensitivity was developed and tested by Siemens during the last years. Now this system has been installed in a Nuclear Power Plant. The experiences gained during the qualification test and the first months of operation can be reported. (author)

Drought stress affects plant metabolites and herbivore preference but not host location by its parasitoids

NARCIS (Netherlands)

Weldegergis, B.T.; Zhu, F.; Poelman, E.H.; Dicke, M.

2015-01-01

One of the main abiotic stresses that strongly affects plant survival and the primary cause of crop loss around the world is drought. Drought stress leads to sequential morphological, physiological, biochemical and molecular changes that can have severe effects on plant growth, development and

Potential bioethanol feedstock availability around nine locations in the Republic of Ireland

Energy Technology Data Exchange (ETDEWEB)

Deverell, R.; McDonnell, K.; Devlin, G. [Department of Biosystems Engineering, Agriculture and Food Science Building, University College Dublin, Belfield (Ireland)

2009-07-01

The Republic of Ireland, like many other countries is trying to diversify energy sources to counteract environmental, political and social concerns. Bioethanol from domestically grown agricultural crops is an indigenously produced alternative fuel that can potentially go towards meeting the goal of diversified energy supply. The Republic of Ireland's distribution of existing soils and agricultural land-uses limit arable crop land to around 10% of total agricultural area. Demand for land to produce arable crops is expected to decrease, which could open the opportunity for bioethanol production. Bioethanol production plants are required to be of a sufficient scale in order to compete economically with other fuel sources, it is important therefore to determine if enough land exists around potential ethanol plant locations to meet the potential demands for feedstock. This study determines, through the use of a developed GIS based model, the potential quantities of feedstock that is available in the hinterlands of nine locations in the Republic of Ireland. The results indicate that three locations can meet all its feedstock demands using indigenously grown sugarbeet, while only one location can meet its demands using a combination of indigenous wheat and straw as the two locally sourced feedstocks. (author)

Potential Bioethanol Feedstock Availability Around Nine Locations in the Republic of Ireland

Directory of Open Access Journals (Sweden)

Rory Deverell

2009-03-01

Full Text Available The Republic of Ireland, like many other countries is trying to diversify energy sources to counteract environmental, political and social concerns. Bioethanol from domestically grown agricultural crops is an indigenously produced alternative fuel that can potentially go towards meeting the goal of diversified energy supply. The Republic of Ireland’s distribution of existing soils and agricultural land-uses limit arable crop land to around 10% of total agricultural area. Demand for land to produce arable crops is expected to decrease, which could open the opportunity for bioethanol production. Bioethanol production plants are required to be of a sufficient scale in order to compete economically with other fuel sources, it is important therefore to determine if enough land exists around potential ethanol plant locations to meet the potential demands for feedstock. This study determines, through the use of a developed GIS based model, the potential quantities of feedstock that is available in the hinterlands of nine locations in the Republic of Ireland. The results indicate that three locations can meet all its feedstock demands using indigenously grown sugarbeet, while only one location can meet its demands using a combination of indigenous wheat and straw as the two locally sourced feedstocks.

Surveillance system for nuclear power plants

International Nuclear Information System (INIS)

Mizeracki, M.T.

1981-01-01

This paper describes an integrated surveillance system for nuclear power plant application. The author explores an expanded role for closed circuit television, with remotely located cameras and infrared scanners as the basic elements. The video system, integrated with voice communication, can enhance the safe and efficient operation of the plant, by improving the operator's knowledge of plant conditions. 7 refs

Uptake of radionuclides by vegetation at a High Arctic location

International Nuclear Information System (INIS)

Dowdall, M.; Gwynn, J.P.; Moran, C.; O'Dea, J.; Davids, C.; Lind, B.

2005-01-01

Radionuclide levels in vegetation from a High Arctic location were studied and compared to in situ soil concentrations. Levels of the anthropogenic radionuclide 137 Cs and the natural radionuclides 40 K, 238 U, 226 Ra and 232 Th are discussed and transfer factor (TF) values and aggregated transfer (Tag) values are calculated for vascular plants. Levels of 137 Cs in vegetation generally followed the order mosses > lichen > vascular plants. The uptake of 137 Cs in vascular plants showed an inverse relationship with the uptake of 40 K, with 137 Cs TF and Tag values generally higher than 40 K TF and Tag values. 40 K activity concentrations in all vegetation showed little correlation to associated soil concentrations, while the uptake of 238 U, 226 Ra and 232 Th by vascular and non-vascular plants was generally low. - Uptake of the anthropogenic radionuclide 137 Cs is highest for moss species

1170-MW(t) HTGR-PS/C plant application-study report: alumina-plant application

International Nuclear Information System (INIS)

Rao, R.; McMain, A.T. Jr.; Stanley, J.D.

1981-05-01

This report considers the HTGR-PS/C application to producing alumina from bauxite. For the size alumina plant considered, the 1170-MW(t) HTGR-PS/C supplies 100% of the process steam and electrical power requirements and produces surplus electrical power and/or process steam, which can be used for other process users or electrical power production. Presently, the bauxite ore is reduced to alumina in plants geographically separated from the electrolysis plant. The electrolysis plants are located near economical electric power sources. However, with the integration of an 1170-MW(t) HTGR-PS/C unit in a commercial alumina plant, the excess electric power available [approx. 233 MW(e)] could be used for alumina electrolysis

Region 9 NPDES Facilities - Waste Water Treatment Plants

Science.gov (United States)

Point geospatial dataset representing locations of NPDES Waste Water Treatment Plant Facilities. NPDES (National Pollution Discharge Elimination System) is an EPA permit program that regulates direct discharges from facilities that discharge treated waste water into waters of the US. Facilities are issued NPDES permits regulating their discharge as required by the Clean Water Act. A facility may have one or more outfalls (dischargers). The location represents the facility or operating plant.

A location procedure for sound sources in reactor-technical enclosures

International Nuclear Information System (INIS)

Hamann, D.

1982-07-01

A passive method requiring one detector only has been developed for the location of sound emitting faults in nuclear power plant components. It is adapted for use in a frequency range the wavelength of which is of the same order of magnitude as characteristic dimensions of the considered enclosure. The location is performed in the following way: (1) For a fixed detector position the Auto Power Spectral Density (APSD) of the source to be located is measured. (2) For this detector position the APSD is calculated for the potential source locations. For this, the free-field APSD as well as the acoustic normal modes of the enclosure are necessary. (3) The measured APSD is compared with the theoretically obtained APSD's. (4) That APSD is determined which is most similar to the measured APSD, and consequently an information about the unknown source position is got. (author)

Location Selection for Hardboard Industry in Mazandaran Province

Directory of Open Access Journals (Sweden)

Majid Azizi

2012-01-01

Full Text Available This research presents an optimum framework for hardboard industry location selection in Mazandaran Province. Considering the existence of only two depreciated hardboard plants with very old technology in Iran, the establishment of new plants are vital. To materialize this goal, Mazandaran province enjoys priorities to other provinces based on its resources of raw lignocellulosic materials required for wood and paper industries. The model presented in this article uses AHP benefit/cost ratios. The results indicate that the criterion of ‘material and production’ with a weight of 0.327 and the sub-criterion of ‘reliability of supply’ with a weight of 0.146 have the highest priorities, and the city of Sari is the best alternative.

The prediction of the LWR plant accident based on the measured plant data

International Nuclear Information System (INIS)

Miettinen, J.; Schmuck, P.

2005-01-01

In case of accident affecting a nuclear reactor, it is essential to anticipate the possible development of the situation to efficiently succeed in emergency response actions, i.e. firstly to be early warned, to get sufficient information on the plant: and as far as possible. The ASTRID (Assessment of Source Term for Emergency Response based on Installation Data) project consists in developing a methodology: of expertise to; structure the work of technical teams and to facilitate cross competence communications among EP players and a qualified computer tool that could be commonly used by the European countries to reliably predict source term in case of an accident in a light water reactor, using the information available on the plant. In many accident conditions the team of analysts may be located far away from the plant experiencing the accident and their decision making is based on the on-line plant data transmitted into the crisis centre in an interval of 30 - 600 seconds. The plant condition has to be diagnosed based on this information, In the ASTRID project the plant status diagnostics has been studied for the European reactor types including BWR, PWR and VVER plants. The directly measured plant data may be used for estimations of the break size from the primary system and its locations. The break size prediction may be based on the pressurizer level, reactor vessel level, primary pressure and steam generator level in the case of the steam generator tube rupture. In the ASTRID project the break predictions concept was developed and its validity for different plant types and is presented in the paper, when the plant data has been created with the plant specific thermohydraulic simulation model. The tracking simulator attempts to follow the plant behavior on-line based on the measured plant data for the main process parameters and most important boundary conditions. When the plant state tracking fails, the plant may be experiencing an accident, and the tracking

FIREDATA, Nuclear Power Plant Fire Event Data Base

International Nuclear Information System (INIS)

Wheelis, W.T.

2001-01-01

1 - Description of program or function: FIREDATA contains raw fire event data from 1965 through June 1985. These data were obtained from a number of reference sources including the American Nuclear Insurers, Licensee Event Reports, Nuclear Power Experience, Electric Power Research Institute Fire Loss Data and then collated into one database developed in the personal computer database management system, dBASE III. FIREDATA is menu-driven and asks interactive questions of the user that allow searching of the database for various aspects of a fire such as: location, mode of plant operation at the time of the fire, means of detection and suppression, dollar loss, etc. Other features include the capability of searching for single or multiple criteria (using Boolean 'and' or 'or' logical operations), user-defined keyword searches of fire event descriptions, summary displays of fire event data by plant name of calendar date, and options for calculating the years of operating experience for all commercial nuclear power plants from any user-specified date and the ability to display general plant information. 2 - Method of solution: The six database files used to store nuclear power plant fire event information, FIRE, DESC, SUM, OPEXPER, OPEXBWR, and EXPERPWR, are accessed by software to display information meeting user-specified criteria or to perform numerical calculations (e.g., to determine the operating experience of a nuclear plant). FIRE contains specific searchable data relating to each of 354 fire events. A keyword concept is used to search each of the 31 separate entries or fields. DESC contains written descriptions of each of the fire events. SUM holds basic plant information for all plants proposed, under construction, in operation, or decommissioned. This includes the initial criticality and commercial operation dates, the physical location of the plant, and its operating capacity. OPEXPER contains date information and data on how various plant locations are

Public Reactions to New Street Tree Planting

Directory of Open Access Journals (Sweden)

Ruth A. Rae

2010-01-01

Full Text Available MillionTreesNYC, which has the goal of planting one million trees in New York City by 2017, is intended to make New York City a greener, more sustainable city and is part of the Mayor’s comprehensive long term strategic plan, PlaNYC. Through planting a tree at every suitable sidewalk location in the city, the City of New York is transforming blocks and communities, and providing a variety of environmental, social and aesthetic benefits. This article examines the large scale municipal planting of new street trees and the reaction by some of the pubic to this planting.Trees offer benefits to the city overall, but the public may not understand these benefits or the street tree planting process. Between 2007 and 2009, the Department of Parks & Recreation planted 53,235 new street trees, and received 4,108 items of correspondence from the public. The majority of this correspondence consisted of public comments about the City’s new street tree planting policies and processes including placement objections, maintenance concerns, reports of resultant damage from tree planting operations, requests for new street trees and reports of tree conditions.This study describes the operational policies that guide New York City's municipal street tree planting, and results of content and spatial analysis of the correspondence. Qualitative analysis of the correspondence revealed the public perceptions and concerns related to the MillionTreesNYC program. Spatial analysis explored the relationship between the planting locations of new street trees and the locations of the citizen correspondence.Public reactions to this large scale municipal planting are related to the dual public and private nature of the sidewalk, issues of territoriality, responsibility, aesthetics and place attachment. Correspondence volume was associated with the scale of the new street tree block planting program, and the effectiveness of NYC’s 311 Customer Service Center. The discussion

Uptake of radionuclides by wheat roots with respect to location of contamination below the surface

International Nuclear Information System (INIS)

Suvornmongkhol, Narumon.

1996-01-01

The behaviour of 85 Sr, 137 Cs, 54 Mn and 60 Co in terms of plant availability in near surface soil and their root uptake was studied as a function of the location of contamination in the soil profile. Wheat (Triticum aestivum) was employed and the study programme involved both column and hydroponic studies. In the column studies, columns were packed with sandy soil, and either homogeneously or discretely contaminated with the radionuclides, and the water table maintained manually at 3 cm from the bottom. In the discrete contamination, the location of contamination was varied (0-5, 25-30 or 45-50 cm from the top). Wheat plants were grown to maturity in these columns, and harvested at different growth stages to examine radioactivity uptake and its subsequent translocation within the plants. The movement of radionuclides within the soil as well as the soil physicochemical properties were also investigated. The short term uptake kinetics of the hydroponically grown plants during ontogenesis were also studied, both with excised roots and intact plants. The excised root experiment was aimed at investigating the radionuclide by roots of different orders. (author)

Vitality of plants to live in the indoor environment

Science.gov (United States)

Shamsuri, Mohd Mahathir Suhaimi; Leman, A. M.; Hariri, Azian; Idris, Ahmad Fu'ad; Afandi, Azizi

2017-09-01

Indoor air quality (IAQ) is generally a public concern because 90% of people spend their time indoor. IAQ must be preserved wisely to guarantee the health of the building occupants. One of the ways to maintain the quality of air is by placing plants in the building. However, all plants come from the outdoor, and the environment is different compared to indoor. Environmental factors such as temperature and light will absolutely affect the growth of the plant. Light and temperature that are too bright or too deem can wither the plants. Nevertheless, certain plant is capable of adapting with different situation after assimilation process has been conducted. This study intends to analyze the capacity of seven selected plants (Anthurium, Dumb Cane, Golden Pothos, Kadaka Fern, Prayer Plant, Spider Plant, and Syngonium) to live in an indoor environment. The vitality of plants is based on photosynthetic level that is measured using leaf - chamber (LI-COR 6400). Two groups of plants were located in indoor and outdoor (indigenous location) setting, and were allowed to assimilate for two months before measurement were carried out. The results for the plant located indoor shows that only Spider Plant cannot perform photosynthesis under 300 lux, where the photosynthetic value remains negative. Meanwhile, other plants such as Anthurium, Dumb Cane, Golden Pothos, Kadaka Fern, Prayer Plant, and Syngonium that were left indoor showed similar 300 lux in which conform the ability of the plants to perform photosynthesis with the value of 0.3, 0.15, 0.35, 0.1, 0.15, and 0.1. In comparison, all of the plants that were stationed indoor and outdoor (except Spider Plant), the light compensation point (LCP) for indoor shows smaller value than the outdoor. This is because all the indoor plants had down - regulated their photosynthesis process by becoming more sensitive to light after their assimilation. From this study, it can be concluded that all plants except Spider Plant is able to live

Plants having modified response to ethylene

Science.gov (United States)

Meyerowitz, E.M.; Chang, C.; Bleecker, A.B.

1997-11-18

The invention includes transformed plants having at least one cell transformed with a modified ETR nucleic acid. Such plants have a phenotype characterized by a decrease in the response of at least one transformed plant cell to ethylene as compared to a plant not containing the transformed plant cell. Tissue and/or temporal specificity for expression of the modified ETR nucleic acid is controlled by selecting appropriate expression regulation sequences to target the location and/or time of expression of the transformed nucleic acid. The plants are made by transforming at least one plant cell with an appropriate modified ETR nucleic acid, regenerating plants from one or more of the transformed plant cells and selecting at least one plant having the desired phenotype. 31 figs.

30 CFR 827.12 - Coal preparation plants: Performance standards.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal preparation plants: Performance standards...-COAL PREPARATION PLANTS NOT LOCATED WITHIN THE PERMIT AREA OF A MINE § 827.12 Coal preparation plants..., modification, reclamation, and removal activities at coal preparation plants shall comply with the following...

7 CFR 1033.7 - Pool plant.

Science.gov (United States)

2010-01-01

... association and it fulfills the following conditions: (1) The aggregate monthly quantity supplied by all... or aseptically-processed fluid milk products. (c) A supply plant from which the quantity of bulk... operator of a supply plant located within the marketing area may include deliveries to pool distributing...

The Power Plant Mapping Student Project: Bringing Citizen Science to Schools

Science.gov (United States)

Tayne, K.; Oda, T.; Gurney, K. R.; O'Keeffe, D.; Petron, G.; Tans, P. P.; Frost, G. J.

2014-12-01

An emission inventory (EI) is a conventional tool to quantify and monitor anthropogenic emissions of greenhouse gases and air pollutants into the atmosphere. Gridded EI can visually show geographical patterns of emissions and their changes over time. These patterns, when available, are often determined using location data collected by regional governments, industries, and researchers. Datasets such as Carbon Monitoring and Action (CARMA, www.carma.org) are particularly useful for mapping emissions from large point sources and have been widely used in the EI community. The EI community is aware of potentially significant errors in the geographical locations of point sources, including power plants. The big challenge, however, is to review tens of thousands of power plant locations around the world and correct them where needed. The Power Plant Mapping Student Project (PPMSP) is a platform designed for students in 4th through 12th grade to improve the geographical location of power plants indicated in existing datasets to benefit international EI research. In PPMSP, we use VENTUS, a web-based platform (http://ventus.project.asu.edu/) that invites citizens to contribute power plant location data. Using VENTUS, students view scenes in the vicinity of reported power plant coordinates on Google Maps. Students either verify the location of a power plant or search for it within a designated radius using various indicators, an e-guide, and a power plant photo gallery for assistance. If the power plant cannot be found, students mark the plant as unverified. To assure quality for research use, the project contains multiple checkpoints and levels of review. While participating in meaningful research that directly benefits the EI research community, students are engaged in relevant science curricula designed to meet each grade level's Next Generation Science Standards. Students study energy, climate change, the atmosphere, and geographical information systems. The curricula is

Plant automation and CRT display system for nuclear power plants

International Nuclear Information System (INIS)

Tekiguchi, S.; Sukai, K.; Watanabe, N.; Yamasaki, M.

1987-01-01

The reliability of plant operation is greatly improved by utilizing selected data for display in real-time on the screens of 12 color CRTs in the Central Control Room and voice information. The load on operators is reduced by automated operation of plant equipment and an operation guide. Information from the power station is transmitted to an off-site location via an optical fiber data way which makes it possible to display in real-time the same CRT screens displayed in the Central Control Room

Location, Location, Location: Does Place Provide the Opportunity for Differentiation for Universities?

Science.gov (United States)

Winter, Emma; Thompson-Whiteside, Helen

2017-01-01

The fiercely competitive HE market has led HEIs to invest significant resources in building a distinct identity. An HEI's location forms an inherent part of its identity and the uniqueness of location offers an opportunity to differentiate. However there has been limited examination of how location is used by HEIs and little consideration of how…

Process Experimental Pilot Plant

International Nuclear Information System (INIS)

Henze, H.

1986-01-01

The Process Experimental Pilot Plant (PREPP) at the Idaho National Engineering Laboratory (INEL) was built to convert transuranic contaminated solid waste into a form acceptable for disposal at the Waste Isolation Pilot Plant (WIPP), located near Carlsbad, New Mexico. There are about 2.0 million cubic ft of transuranic waste stored at the Transuranic Storage Area of the INEL's Radioactive Waste Management Complex (RWMC). The Stored Waste Examination Pilot Plant (SWEPP) located at the RWMC will examine this stored transuranic waste to determine if the waste is acceptable for direct shipment to and storage at WIPP, or if it requires shipment to PREPP for processing before shipment to WIPP. The PREPP process shreds the waste, incinerates the shredded waste, and cements (grouts) the shredded incinerated waste in new 55-gal drums. Unshreddable items are repackaged and returned to SWEPP. The process off-gas is cleaned prior to its discharge to the atmosphere, and complies with the effluent standards of the State of Idaho, EPA, and DOE. Waste liquid generated is used in the grouting operation

Oak Ridge Y-12 Plant groundwater protection program management plan

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

The Oak Ridge Y- 1 2 Plant (Y-12 Plant) is owned by the United States Department of Energy (DOE) and managed by Lockheed Martin Energy Systems, Inc. (Energy Systems) under contract No. DE-AC05-84OR21400. The Y-12 Plant Groundwater Protection Program (GWPP), which was initiated in 1975, provides for the protection of groundwater resources consistent with Federal, State, and local regulations, and in accordance with DOE orders and Energy Systems policies and procedures. The Y-12 Plant is located in Anderson County, Tennessee, and is within the corporate limits of the City of Oak Ridge. The Y-12 Plant is one of three major DOE complexes that comprise the 37,000-acre Oak Ridge Reservation (ORR) located in Anderson and Roane counties. The Y-12 Plant is located in Bear Creek Valley at an elevation of about 950 feet (ft) above sea level. Bear Creek Valley is bounded on the northwest and southeast, and is isolated from populated areas of Oak Ridge, by parallel ridges that rise about 300 ft above the valley floor. The Y-12 Plant and its fenced buffer area are about 0.6 mile wide by 3.2 miles long and cover approximately 4,900 acres. The main industrialized section encompasses approximately 800 acres.

Oak Ridge Y-12 Plant groundwater protection program management plan

International Nuclear Information System (INIS)

1996-06-01

The Oak Ridge Y- 1 2 Plant (Y-12 Plant) is owned by the United States Department of Energy (DOE) and managed by Lockheed Martin Energy Systems, Inc. (Energy Systems) under contract No. DE-AC05-84OR21400. The Y-12 Plant Groundwater Protection Program (GWPP), which was initiated in 1975, provides for the protection of groundwater resources consistent with Federal, State, and local regulations, and in accordance with DOE orders and Energy Systems policies and procedures. The Y-12 Plant is located in Anderson County, Tennessee, and is within the corporate limits of the City of Oak Ridge. The Y-12 Plant is one of three major DOE complexes that comprise the 37,000-acre Oak Ridge Reservation (ORR) located in Anderson and Roane counties. The Y-12 Plant is located in Bear Creek Valley at an elevation of about 950 feet (ft) above sea level. Bear Creek Valley is bounded on the northwest and southeast, and is isolated from populated areas of Oak Ridge, by parallel ridges that rise about 300 ft above the valley floor. The Y-12 Plant and its fenced buffer area are about 0.6 mile wide by 3.2 miles long and cover approximately 4,900 acres. The main industrialized section encompasses approximately 800 acres

Region 9 NPDES Facilities 2012- Waste Water Treatment Plants

Science.gov (United States)

Point geospatial dataset representing locations of NPDES Waste Water Treatment Plant Facilities. NPDES (National Pollution Discharge Elimination System) is an EPA permit program that regulates direct discharges from facilities that discharge treated waste water into waters of the US. Facilities are issued NPDES permits regulating their discharge as required by the Clean Water Act. A facility may have one or more outfalls (dischargers). The location represents the facility or operating plant.

Habitat models to assist plant protection efforts in Shenandoah National Park, Virginia, USA

Science.gov (United States)

Van Manen, F.T.; Young, J.A.; Thatcher, C.A.; Cass, W.B.; Ulrey, C.

2005-01-01

During 2002, the National Park Service initiated a demonstration project to develop science-based law enforcement strategies for the protection of at-risk natural resources, including American ginseng (Panax quinquefolius L.), bloodroot (Sanguinaria canadensis L.), and black cohosh (Cimicifuga racemosa (L.) Nutt. [syn. Actaea racemosa L.]). Harvest pressure on these species is increasing because of the growing herbal remedy market. We developed habitat models for Shenandoah National Park and the northern portion of the Blue Ridge Parkway to determine the distribution of favorable habitats of these three plant species and to demonstrate the use of that information to support plant protection activities. We compiled locations for the three plant species to delineate favorable habitats with a geographic information system (GIS). We mapped potential habitat quality for each species by calculating a multivariate statistic, Mahalanobis distance, based on GIS layers that characterized the topography, land cover, and geology of the plant locations (10-m resolution). We tested model performance with an independent dataset of plant locations, which indicated a significant relationship between Mahalanobis distance values and species occurrence. We also generated null models by examining the distribution of the Mahalanobis distance values had plants been distributed randomly. For all species, the habitat models performed markedly better than their respective null models. We used our models to direct field searches to the most favorable habitats, resulting in a sizeable number of new plant locations (82 ginseng, 73 bloodroot, and 139 black cohosh locations). The odds of finding new plant locations based on the habitat models were 4.5 (black cohosh) to 12.3 (American ginseng) times greater than random searches; thus, the habitat models can be used to improve the efficiency of plant protection efforts, (e.g., marking of plants, law enforcement activities). The field searches also

Ecotoxicological relations on a large pig fattening farm located in a lignite mining area and near a solid fuel power plant

Energy Technology Data Exchange (ETDEWEB)

Raszyk, J.; Docekalova, H.; Rubes, J.; Gajduskova, V.; Masek, J.; Rodak, L.; Bartos, J. (Veterinary Research Institute, Brno (Czechoslovakia))

1992-01-01

Major contaminants identified in 1983-1984 on a pig fattening farm located in a lignite mining area and near a solid fuel power plant, were mercury, cadmium, lead, chromium and aflatoxin B1. Feed samples were collected to assess the contamination load at feed uptake. Permissible concentrations of mercury, chromium, cadmium, aflatoxin B1, lead and atrazin in the feed were exceeded in 56, 50, 31, 19, 6 and 6% samples, respectively. Permissible concentrations of mercury, cadmium and lead in porcine muscles were exceeded in 65, 51, 24% samples, respectively. Pigs fattened in the contaminated environment (i.e. fed contaminated feed mixtures, inspiring contaminated dust and absorbing percutaneously contaminants from dust deposits on the body surface) showed: (1) impairment of the genetic apparatus; (2) a certain degree of immunosuppression; (3) higher feed consumption per 1 kg weight gain and lower average daily weight gain; (4) increased incidence of health disorders. The authors were not allowed to analyse ash and solid emissions from the power plant. Therefore the share of the emissions in the overall environmental contamination on the fattening farm could not be quantified. The personnel, working in the contaminated environment for a prolonged period, are endangered most of all by stable dust, being exposed to its mechanical, chemical, allergic and infectious effects. Consumption of meat and organs from pigs fattened in a contaminated environment is associated with the risk of an increased uptake of various contaminants.

Evaluation of Need and Location for a Thermogravimetric Analyzer in the Plutonium Finishing Plant (PFP) Materials Stabilization

International Nuclear Information System (INIS)

WILLIS, H.T.

2000-01-01

This plan provides an analysis for locating a TGA to support PFP Thermal Stabilization processes. The scope of this document is to evaluate the need for, and location for, installation of a TGA system as a supplement to the SFE equipment for moisture measurement in pure oxides. A location assessment for the SFE equipment was previously performed (HNF 1999). Based on that assessment, co-location of the TGA system with the SFE system is the preferred option. This would enable thermally stabilized material to be analyzed for residual moisture by either the TGA system or SFE system or both This evaluation considers glovebox locations in the PFP 234-52 Building Analytical Laboratory or operating areas for the installation of the TGA system and it's supporting equipment. This evaluation considers using existing gloveboxes along with an alternative of adding a new glovebox to existing process lines. The location evaluation criteria focuses mainly on glovebox size, with qualitative consideration of relative cost and schedule impacts associated with system implementation, radiological control, and interaction with other laboratory operations and processes. In addition, the possible co-location of a TGA furnace system with the SFE system was considered

30 CFR 827.13 - Coal preparation plants: Interim performance standards.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal preparation plants: Interim performance...-COAL PREPARATION PLANTS NOT LOCATED WITHIN THE PERMIT AREA OF A MINE § 827.13 Coal preparation plants: Interim performance standards. (a) Persons operating or who have operated coal preparation plants after...

Technology-Enhanced Formative Assessment of Plant Identification

Science.gov (United States)

Conejo, Ricardo; Garcia-Viñas, Juan Ignacio; Gastón, Aitor; Barros, Beatriz

2016-04-01

Developing plant identification skills is an important part of the curriculum of any botany course in higher education. Frequent practice with dried and fresh plants is necessary to recognize the diversity of forms, states, and details that a species can present. We have developed a web-based assessment system for mobile devices that is able to pose appropriate questions according to the location of the student. A student's location can be obtained using the device position or by scanning a QR code attached to a dried plant sheet in a herbarium or to a fresh plant in an arboretum. The assessment questions are complemented with elaborated feedback that, according to the students' responses, provides indications of possible mistakes and correct answers. Three experiments were designed to measure the effectiveness of the formative assessment using dried and fresh plants. Three questionnaires were used to evaluate the system performance from the students' perspective. The results clearly indicate that formative assessment is objectively effective compared to traditional methods and that the students' attitudes towards the system were very positive.

SECURE nuclear district heating plant

International Nuclear Information System (INIS)

Nilsson; Hannus, M.

1978-01-01

The role foreseen for the SECURE (Safe Environmentally Clean Urban REactor) nuclear district heating plant is to provide the baseload heating needs of primarily the larger and medium size urban centers that are outside the range of waste heat supply from conventional nuclear power stations. The rationale of the SECURE concept is that the simplicity in design and the inherent safety advantages due to the use of low temperatures and pressures should make such reactors economically feasible in much smaller unit sizes than nuclear power reactors and should make their urban location possible. It is felt that the present design should be safe enough to make urban underground location possible without restriction according to any criteria based on actual risk evaluation. From the environmental point of view, this is a municipal heat supply plant with negligible pollution. Waste heat is negligible, gaseous radioactivity release is negligible, and there is no liquid radwaste release. Economic comparisons show that the SECURE plant is competitive with current fossil-fueled alternatives. Expected future increase in energy raw material prices will lead to additional energy cost advantages to the SECURE plant

Improving geothermal power plants with a binary cycle

Science.gov (United States)

Tomarov, G. V.; Shipkov, A. A.; Sorokina, E. V.

2015-12-01

The recent development of binary geothermal technology is analyzed. General trends in the introduction of low-temperature geothermal sources are summarized. The use of single-phase low-temperature geothermal fluids in binary power plants proves possible and expedient. The benefits of power plants with a binary cycle in comparison with traditional systems are shown. The selection of the working fluid is considered, and the influence of the fluid's physicochemical properties on the design of the binary power plant is discussed. The design of binary power plants is based on the chemical composition and energy potential of the geothermal fluids and on the landscape and climatic conditions at the intended location. Experience in developing a prototype 2.5 MW Russian binary power unit at Pauzhetka geothermal power plant (Kamchatka) is outlined. Most binary systems are designed individually for a specific location. Means of improving the technology and equipment at binary geothermal power plants are identified. One option is the development of modular systems based on several binary systems that employ the heat from the working fluid at different temperatures.

7 CFR 1006.7 - Pool plant.

Science.gov (United States)

2010-01-01

... Class I or Class II products and must be located in a pricing zone providing the same or a lower Class I... (excluding concentrated milk received from another plant by agreement for other than Class I use) are... (excluding concentrated milk received from another plant by agreement for other than Class I use) into ultra...

Experiences on sea water reverse osmosis plant at Anuvijay township, Kudankulam Nuclear Power Plant

International Nuclear Information System (INIS)

Balasubramanian, M.R.; Selvavinayagam, P.; Singaravelan, S.; Ramdoss, R.; Sundar, R.S.

2007-01-01

Sea water reverse Osmosis plant SWRO of KKNPP is located at Anuvijay township, Chettikulam, Tirunelveli District, Tamilnadu. The objective of SWRO is to produce 2400 M 3 of potable quality water per day. This plant consists of four streams, each having a capacity of 25 M 3 /hr. Each stream is having 9 pressure tube in parallel and each pressure tube has 6 polyamide spiral wound membrane in series. (author)

Nuclear Power Plants (Rev.)

Energy Technology Data Exchange (ETDEWEB)

Lyerly, Ray L.; Mitchell III, Walter [Southern Nuclear Engineering, Inc.

1973-01-01

Projected energy requirements for the future suggest that we must employ atomic energy to generate electric power or face depletion of our fossil-fuel resources—coal, oil, and gas. In short, both conservation and economic considerations will require us to use nuclear energy to generate the electricity that supports our civilization. Until we reach the time when nuclear power plants are as common as fossil-fueled or hydroelectric plants, many people will wonder how the nuclear plants work, how much they cost, where they are located, and what kinds of reactors they use. The purpose of this booklet is to answer these questions. In doing so, it will consider only central station plants, which are those that provide electric power for established utility systems.

A novel technique to extract events from access control system and locate persons

International Nuclear Information System (INIS)

Vincent, M.; Vaidyanathan, Mythili; Patidar, Suresh Chandra; Prabhakara Rao, G.

2011-01-01

Indira Gandhi Centre for Atomic Research houses many laboratories which handle radioactive materials and classified materials. Protection and accounting of men and material and critical facilities are important aspect of nuclear security. Access Control System (ACS) is used to enhance the protective measures against elevated threat environment. Access control system hardware consists of hand geometry readers, RFID readers, Controllers, Electromagnetic door locks, Turnstiles, fiber cable laying and termination etc. Access Control System controls and monitors the people accessing the secured facilities. Access Control System generates events on: 1. Showing of RFID card, 2. Rotation of turnstile, 3. Download of valid card numbers, 4. Generation of alarms etc. Access control system turnstiles are located in main entrance of a facility, entrance of inside laboratory and door locks are fixed on secured facilities. Events are stored in SQL server database. From the events stored in database a novel technique is developed to extract events and list the persons in a particular facility, list all entry/exit events on one day, list the first in and last out entries. This paper discusses the complex multi level group by queries and software developed to extract events from database, locate persons and generate reports. Software is developed as a web application in ASP.Net and query is written in SQL. User can select the doors, type of events and generate reports. Reports are generated using the master data stored about employees RFID cards and events data stored in tables. Four types of reports are generated 1. Plant Emergency Report, 2. Locate User Report, 3. Entry - Exit Report, 4. First in Last out Report. To generate plant emergency report for whole plant only events generated in outer gates have to be considered. To generate plant emergency report for inside laboratory, events generated in entrance gates have to be ignored. (author)

A COUNTY-LEVEL MODEL OF MANUFACTURING PLANT RECRUITMENT WITH IMPROVED INDUSTRIAL SITE QUALITY MEASUREMENT

OpenAIRE

Kriesel, Warren; McNamara, Kevin T.

1991-01-01

Empirical analysis of manufacturing plant location requires the use of a single industrial site quality measure. Under hedonic price theory, the price of industrial sites can be explained by their quality characteristics. The estimated site price is included with ten other location factors in an ordered, categorical logit model of plant attraction to Georgia counties. The results inform public decision-makers of the relative impact of site location factors and how changes in location factors ...

Application of Artificial Neural Network for Predicting Iron Concentration in the Location of Al-Wahda Water Treatment Plant in Baghdad City

Directory of Open Access Journals (Sweden)

Nawar Omran Ali Al-Musawi

2016-09-01

Full Text Available Iron is one of the abundant elements on earth that is an essential element for humans and may be a troublesome element in water supplies. In this research an AAN model was developed to predict iron concentrations in the location of Al- Wahda water treatment plant in Baghdad city by water quality assessment of iron concentrations at seven WTPs up stream Tigris River. SPSS software was used to build the ANN model. The input data were iron concentrations in the raw water for the period 2004-2011. The results indicated the best model predicted Iron concentrations at Al-Wahda WTP with a coefficient of determination 0.9142. The model used one hidden layer with two nodes and the testing error was 0.834. The ANN model could be used to predict future iron concentrations as the results from the verification of the ANN model for years 2012 and 2013 indicated good accuracy with a coefficient of determination R2 = 0.8965.

Nuclear Power Plants in the World

International Nuclear Information System (INIS)

2003-01-01

The Japan Atomic Industrial Forum (JAIF) used every year to summarize a trend survey on the private nuclear power plants in the world in a shape of the 'Nuclear power plants in the world'. In this report, some data at the end of 2002 was made up on bases of answers on questionnaires from 65 electric power companies and other nuclear organizations in 28 countries and regions around the world by JAIF. This report is comprised of 19 items, and contains generating capacity of the plants; current status of Japan; trends of generating capacity of operating the plants, the plant orders and generating capacity of the plants; world nuclear capacity by reactor type; status of MOX use in the world; location of the plants; the plants in the world; directory of the plants; nuclear fuel cycle facilities; and so forth. (J.P.N.)

Habitats as complex odour environments: how does plant diversity affect herbivore and parasitoid orientation?

Directory of Open Access Journals (Sweden)

Nicole Wäschke

Full Text Available Plant diversity is known to affect success of host location by pest insects, but its effect on olfactory orientation of non-pest insect species has hardly been addressed. First, we tested in laboratory experiments the hypothesis that non-host plants, which increase odour complexity in habitats, affect the host location ability of herbivores and parasitoids. Furthermore, we recorded field data of plant diversity in addition to herbivore and parasitoid abundance at 77 grassland sites in three different regions in Germany in order to elucidate whether our laboratory results reflect the field situation. As a model system we used the herb Plantago lanceolata, the herbivorous weevil Mecinus pascuorum, and its larval parasitoid Mesopolobus incultus. The laboratory bioassays revealed that both the herbivorous weevil and its larval parasitoid can locate their host plant and host via olfactory cues even in the presence of non-host odour. In a newly established two-circle olfactometer, the weeviĺs capability to detect host plant odour was not affected by odours from non-host plants. However, addition of non-host plant odours to host plant odour enhanced the weeviĺs foraging activity. The parasitoid was attracted by a combination of host plant and host volatiles in both the absence and presence of non-host plant volatiles in a Y-tube olfactometer. In dual choice tests the parasitoid preferred the blend of host plant and host volatiles over its combination with non-host plant volatiles. In the field, no indication was found that high plant diversity disturbs host (plant location by the weevil and its parasitoid. In contrast, plant diversity was positively correlated with weevil abundance, whereas parasitoid abundance was independent of plant diversity. Therefore, we conclude that weevils and parasitoids showed the sensory capacity to successfully cope with complex vegetation odours when searching for hosts.

Aktau Plastics Plant Explosives Material Report

Energy Technology Data Exchange (ETDEWEB)

CASE JR.,ROGER S.

1999-12-01

The U.S. Department of Energy (DOE) has been cooperating with the Republic of Kazakhstanin Combined Threat Reduction (CTR) activities at the BN350 reactor located at the Mangyshlak Atomic Energy Complex (MAEC) in the city of Aktau, Kazakhstan since 1994. DOE contract personnel have been stationed at this facility for the last two years and DOE representatives regularly visit this location to oversee the continuing cooperative activities. Continued future cooperation is planned. A Russian news report in September 1999 indicated that 75 metric tons of organic peroxides stored at the Plastics Plant near Aktau were in danger of exploding and killing or injuring nearby residents. To ensure the health and safety of the personnel at the BN350 site, the DOE conducted a study to investigate the potential danger to the BN350 site posed by these materials at the Plastics Plant. The study conclusion was that while the organic peroxides do have hazards associated with them, the BN350 site is a safe distance from the Plastics Plant. Further, because the Plastics Plant and MAEC have cooperative fire-fighting agreements,and the Plastics Plant had exhausted its reserve of fire-fighting foam, there was the possibility of the Plastics Plant depleting the store of fire-fighting foam at the BN350 site. Subsequently, the DOE decided to purchase fire-fighting foam for the Plastics Plant to ensure the availability of free-fighting foam at the BN350 site.

Integrated structural design of nuclear power plants for high seismic areas

International Nuclear Information System (INIS)

Rieck, P.J.

1979-01-01

A design approach which structurally interconnects NPP buildings to be located in high seismic areas is described. The design evolution of a typical 600 MWe steel cylindrical containment PWR is described as the plant is structurally upgraded for higher seismic requirements, while maintaining the original plant layout. The plant design is presented as having separate reactor building and auxiliary structures for a low seismic area (0.20 g) and is structurally combined at the foundation for location in a higher seismic area (0.30 g). The evolution is completed by a fully integrated design which structurally connects the reactor building and auxiliary structures at superstructure elevations as well as foundation levels for location in very severe seismic risk areas (0.50 g). (orig.)

Efficiency of vibrational sounding in parasitoid host location depends on substrate density.

Science.gov (United States)

Fischer, S; Samietz, J; Dorn, S

2003-10-01

Parasitoids of concealed hosts have to drill through a substrate with their ovipositor for successful parasitization. Hymenopteran species in this drill-and-sting guild locate immobile pupal hosts by vibrational sounding, i.e., echolocation on solid substrate. Although this host location strategy is assumed to be common among the Orussidae and Ichneumonidae there is no information yet whether it is adapted to characteristics of the host microhabitat. This study examined the effect of substrate density on responsiveness and host location efficiency in two pupal parasitoids, Pimpla turionellae and Xanthopimpla stemmator (Hymenoptera: Ichneumonidae), with different host-niche specialization and corresponding ovipositor morphology. Location and frequency of ovipositor insertions were scored on cylindrical plant stem models of various densities. Substrate density had a significant negative effect on responsiveness, number of ovipositor insertions, and host location precision in both species. The more niche-specific species X. stemmator showed a higher host location precision and insertion activity. We could show that vibrational sounding is obviously adapted to the host microhabitat of the parasitoid species using this host location strategy. We suggest the attenuation of pulses during vibrational sounding as the energetically costly limiting factor for this adaptation.

Radionuclide transfer from soil to plants

International Nuclear Information System (INIS)

Teufel, D.; Steinhilber-Schwab, B.; Hoepfner, U.; Ratka, R.; Sand, H. van de; Franke, B.

1979-01-01

The planned nuclear reprocessing plant (NEZ) Gorleben will fundamentally differ from actually operating nuclear power plants with regard to its radioactive emissions because relatively long-life isotopes will play a greater role in the emissions. The longevity of the radionuclides emitted in the planned NEZ implies that there will be an accumulation of radionuclides in the surroundings of the plant and long-term effects of the plant on the environment will get higher significance. As radionuclides mainly reach milk and meat via the food of farm animals the transfer of cesium and strontium from the ground into plants was amply investigated. The results show that the correlation calculations are suitable to describe the effect of different parameters on the transfer factor. They are not suited for a forecast of the transfer conditions on a certain location for the reasons explained before. Location-specific measurements seem to be indispensable for these purposes. Besides the greenhouse tests open air measurements of fall-out nuclides with and without elimination of external contamination seem to represent a realistic possibility for the determination of transfer factors. Great attention has to be paid in this kind of tests to the growth conditions (especially fertilization) which have to be accurately registered. (orig./MG) [de

Location, location ... structure

NARCIS (Netherlands)

Cutler, S.; Testerink, C.

2011-01-01

A plant's growth, development and responses to the environment are intimately connected to internal and external signals that, through the action of signal transduction, regulate gene expression and other cellular outputs. Work from laboratories across the globe has deepened our understanding of how

Nuclear power plants in the world

International Nuclear Information System (INIS)

2008-01-01

The Japan Atomic Industrial Forum, Inc. (JAIF) used every year to summarize a trend survey on the private nuclear power plants in the world in a shape of the 'Nuclear power plants in the world'. In this report, some data at the end of 2007/2008 was made up on bases of answers on questionnaires from electric power companies and other nuclear organizations around the world by JAIF. This report is comprised of 18 items, and contains generating capacity of the plants; effect of the Niigata-ken chuetsu-oki earthquake; current status of Japan; trends of generating capacity of operating the plants, the plant orders and generating capacity of the plants; world nuclear capacity by reactor type; status of MOX use in the world; location of the plants; the plants in the world; directory of the plants; nuclear fuel cycle facilities, and so forth. (J.P.N.)

Nuclear Power Plants in the World

International Nuclear Information System (INIS)

2004-01-01

The Japan Atomic Industrial Forum, Inc. (JAIF) used every year to summarize a trend survey on the private nuclear power plants in the world in a shape of the 'Nuclear power plants in the world'. In this report, some data at the end of 2003 was made up on bases of answers on questionnaires from 81 electric power companies and other nuclear organizations in 33 countries and regions around the world by JAIF. This report is comprised of 19 items, and contains generating capacity of the plants; current status of Japan; trends of generating capacity of operating the plants, the plant orders and generating capacity of the plants; world nuclear capacity by reactor type; status of MOX use in the world; location of the plants; the plants in the world; directory of the plants; nuclear fuel cycle facilities; and so forth. (J.P.N.)

Environmental monitoring at the Savannah River Plant. Annual report for 1978

International Nuclear Information System (INIS)

Ashley, C.; Zeigler, C.C.

1981-01-01

The environmental monitoring program at the Savannah River Plant (SRP) provides reliable measurement of radioactive materials released at the source (approximately 40 locations) and present in the environment (approximately 500 locations). In recent years, the environmental monitoring program has been expanded to include measurements of nonradioactive materials released by SRP. A brief discussion of plant releases to the environment and radioactive and nonradioactive materials detected in the environment are presented. The appendices contain data analysis and quality control information, sensitivities of laboratory analyses, tables of environmental sample analyses, and maps of sampling locations

Proposal of an Eco-Industrial Park based on the water desalination plant located inside the King Abdullah University of Science and Technology

KAUST Repository

Lopez Torres, Rodrigo

2016-12-01

This thesis project is a proposal of a scenario of an industrial collaboration that could become the basis for the development of an Eco-Industrial Park inside the King Abdullah University of Science and Technology using the water desalination plant as the foundation of this network. It is defined why the university is a suitable place for a development of this type; what industrial networks can be formed and what environmental, economic and social benefits could be achieved if the Kingdom of Saudi Arabia implemented this project around the country. An Eco-Industrial Park is a collaboration between industries where they share resources and create an exchange network of wastes and by-products with the objective of obtaining positive environmental, economic and social impacts. In the proposed scenario, the initial collaboration is between a PV solar plant and the water desalination located inside the university. With the use of solar energy there are savings of CO2 emissions, which turn into positive impacts on the environment. The idea is that this initial collaboration could be extended in the future to provide the entire energy consumption of the KAUST community. The project also provides an insight into how an industrial symbiosis could be formed taking as a base this industrial collaboration. However, further studies and analysis are required in order to provide more solid information regarding the development of an Eco-Industrial Park.

A Location Privacy Aware Friend Locator

DEFF Research Database (Denmark)

Siksnys, Laurynas; Thomsen, Jeppe Rishede; Saltenis, Simonas

2009-01-01

to trade their location privacy for quality of service, limiting the attractiveness of the services. The challenge is to develop a communication-efficient solution such that (i) it detects proximity between a user and the user’s friends, (ii) any other party is not allowed to infer the location of the user...

Impacts of weather on long-term patterns of plant richness and diversity vary with location and management.

Science.gov (United States)

Jonas, Jayne L; Buhl, Deborah A; Symstad, Amy J

2015-09-01

Better understanding the influence of precipitation and temperature on plant assemblages is needed to predict the effects of climate change. Many studies have examined the relationship between plant productivity and weather (primarily precipitation), but few have directly assessed the relationship between plant richness or diversity and weather despite their increased use as metrics of ecosystem condition. We focus on the grasslands of central North America, which are characterized by high temporal climatic variability. Over the next 100 years, these grasslands are predicted to experience further increased variability in growing season precipitation, as well as increased temperatures, due to global climate change. We assess the portion of interannual variability of richness and diversity explained by weather, how relationships between these metrics and weather vary among plant assemblages, and which aspects of weather best explain temporal variability. We used an information-theoretic approach to assess relationships between long-term plant richness and diversity patterns and a priori weather covariates using six data sets from four grasslands. Weather explained up to 49% and 63% of interannual variability in total plant species richness and diversity, respectively. However, richness and diversity responses to specific weather variables varied both among sites and among experimental treatments within sites. In general, we found many instances in which temperature was of equal or greater importance as precipitation, as well as evidence of the importance of lagged effects and precipitation or temperature variability. Although precipitation has been shown to be a key driver of productivity in grasslands, our results indicate that increasing temperatures alone, without substantial changes in precipitation patterns, could have measurable effects on Great Plains grassland plant assemblages and biodiversity metrics. Our results also suggest that richness and diversity

Root Traits and Phenotyping Strategies for Plant Improvement

OpenAIRE

Ana Paez-Garcia; Christy M. Motes; Wolf-Rüdiger Scheible; Rujin Chen; Elison B. Blancaflor; Maria J. Monteros

2015-01-01

Roots are crucial for nutrient and water acquisition and can be targeted to enhance plant productivity under a broad range of growing conditions. A current challenge for plant breeding is the limited ability to phenotype and select for desirable root characteristics due to their underground location. Plant breeding efforts aimed at modifying root traits can result in novel, more stress-tolerant crops and increased yield by enhancing the capacity of the plant for soil exploration and, thus, wa...

DENINT power plant cost benefit analysis code: Analysis of methane fuelled power plant/district heating system

International Nuclear Information System (INIS)

Cincotti, V.; D'Andrea, A.

1989-07-01

The DENINT power plant cost benefit analysis code takes into consideration, not only power production costs at the generator terminals, but also, in the case of cogeneration, the costs of the fuel supply and heat and power distribution systems which depend greatly on the location of the plant. The code is able to allow comparisons of alternatives with varying annual operation hours, fuel cost increases, and different types of fossil fuels and production systems. For illustrative purposes, this paper examines two methane fired cogeneration plant/district heating alternatives

Taylor Hydro plant goes live

International Nuclear Information System (INIS)

Anon.

2000-01-01

The 12.75 MW Taylor Hydroelectric Plant in Magrath, Alberta, synchronized its generator with the Alberta Power Grid and began production in April 2000. The plant is located on Government of Alberta irrigation works and is owned by Canadian Hydro Developers. During the irrigation season the plant will generate approximately 40 million kilowatt hours of zero-emission 'green' power for consumption, enough to power 5,000 homes for a year. The Taylor plant is a joint venture with EPCOR Power Development Corporation, a wholly-owned subsidiary of EPCOR Inc., the City of Edmonton utility. Canadian Hydro Developers also owns a 19 MW wind plant and a 6 MW gas plant in Alberta and five other 'run of river' hydro plants in Ontario and British Columbia. The company is committed to the concept of low-impact power generation; its ownership of wind run-of-river hydro and gas-fired facilities is proof of that commitment

A multi-objective possibilistic programming approach for locating distribution centers and allocating customers demands in supply chains

Directory of Open Access Journals (Sweden)

Seyed Ahmad Yazdian

2011-01-01

Full Text Available In this paper, we present a multi-objective possibilistic programming model to locate distribution centers (DCs and allocate customers' demands in a supply chain network design (SCND problem. The SCND problem deals with determining locations of facilities (DCs and/or plants, and also shipment quantities between each two consecutive tier of the supply chain. The primary objective of this study is to consider different risk factors which are involved in both locating DCs and shipping products as an objective function. The risk consists of various components: the risks related to each potential DC location, the risk associated with each arc connecting a plant to a DC and the risk of shipment from a DC to a customer. The proposed method of this paper considers the risk phenomenon in fuzzy forms to handle the uncertainties inherent in these factors. A possibilistic programming approach is proposed to solve the resulted multi-objective problem and a numerical example for three levels of possibility is conducted to analyze the model.

Effects of hydrogen fluoride on plants

Energy Technology Data Exchange (ETDEWEB)

Yamazoe, F

1970-07-15

Symptoms of fluorosis in plants are chlorotic markings around the tip or edges of young leaves. Examples of damage to plants and livestock by fluorides are listed, including the retarded growth of silkworms fed on mulberry leaves polluted by more than 30 ppm fluorides. Plants can be classified into six groups according to their resistance to hydrogen fluoride. Threshold values of the fluoride concentration range from 5-10 ppb for the plants. Gladiolus is normally employed as a plant indicator for hydrogen fluoride and silkworms as indicator insects. The relationship between plant damage by fluorides and exposure time, density, soil, fertilizer, meteorology and location are examined. Several preventive measures are listed, including the spraying of water or lime on plant leaves. It is concluded that the establishment of an environmental standard is difficult because of the extremely high sensitivity of the plants to the gas. 8 references.

Medicago truncatula contains a second gene encoding a plastid located glutamine synthetase exclusively expressed in developing seeds

Directory of Open Access Journals (Sweden)

Seabra Ana R

2010-08-01

Full Text Available Abstract Background Nitrogen is a crucial nutrient that is both essential and rate limiting for plant growth and seed production. Glutamine synthetase (GS, occupies a central position in nitrogen assimilation and recycling, justifying the extensive number of studies that have been dedicated to this enzyme from several plant sources. All plants species studied to date have been reported as containing a single, nuclear gene encoding a plastid located GS isoenzyme per haploid genome. This study reports the existence of a second nuclear gene encoding a plastid located GS in Medicago truncatula. Results This study characterizes a new, second gene encoding a plastid located glutamine synthetase (GS2 in M. truncatula. The gene encodes a functional GS isoenzyme with unique kinetic properties, which is exclusively expressed in developing seeds. Based on molecular data and the assumption of a molecular clock, it is estimated that the gene arose from a duplication event that occurred about 10 My ago, after legume speciation and that duplicated sequences are also present in closely related species of the Vicioide subclade. Expression analysis by RT-PCR and western blot indicate that the gene is exclusively expressed in developing seeds and its expression is related to seed filling, suggesting a specific function of the enzyme associated to legume seed metabolism. Interestingly, the gene was found to be subjected to alternative splicing over the first intron, leading to the formation of two transcripts with similar open reading frames but varying 5' UTR lengths, due to retention of the first intron. To our knowledge, this is the first report of alternative splicing on a plant GS gene. Conclusions This study shows that Medicago truncatula contains an additional GS gene encoding a plastid located isoenzyme, which is functional and exclusively expressed during seed development. Legumes produce protein-rich seeds requiring high amounts of nitrogen, we postulate

Seismic reevaluation of existing nuclear power plants

International Nuclear Information System (INIS)

Hennart, J.C.

1978-01-01

The codes and regulations governing Nuclear Power Plant seismic analysis are continuously becoming more stringent. In addition, design ground accelerations of existing plants must sometimes be increased as a result of discovery of faulting zones or recording of recent earthquakes near the plant location after plant design. These new factors can result in augmented seismic design criteria. Seismic reanalysius of the existing Nuclear Power Plant structures and equipments is necessary to prevent the consequences of newly postulated accidents that could cause undue risk to the health or safety of the public. This paper reviews the developments of seismic analysis as applied to Nuclear Power Plants and the methods used by Westinghouse to requalify existing plants to the most recent safety requirements. (author)

Risks of turbine generators at WWER-440 nuclear power plants

International Nuclear Information System (INIS)

Virolainen, T.; Marttila, J.; Aulamo, H.

1998-01-01

Many serious fires and incidents have occurred in the turbine halls of nuclear power plants, resulting in serious damage and long shutdown outages. Some of these incidents have endangered the safe shutdown of the plants because of the location of lack of vital fire protection safety systems. A detailed analysis is necessary for all those plants that have equipment important for safe shutdown located in the turbine hall or its vicinity without strict fire separation by fire rated barriers. A reduction in the fire frequencies of the turbine hall is an additional way of improving safety. This is possible by improving all aspects of turbine generator operation. (author)

Method for assigning sites to projected generic nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Holter, G.M.; Purcell, W.L.; Shutz, M.E.; Young, J.R.

1986-07-01

Pacific Northwest Laboratory developed a method for forecasting potential locations and startup sequences of nuclear power plants that will be required in the future but have not yet been specifically identified by electric utilities. Use of the method results in numerical ratings for potential nuclear power plant sites located in each of the 10 federal energy regions. The rating for each potential site is obtained from numerical factors assigned to each of 5 primary siting characteristics: (1) cooling water availability, (2) site land area, (3) power transmission land area, (4) proximity to metropolitan areas, and (5) utility plans for the site. The sequence of plant startups in each federal energy region is obtained by use of the numerical ratings and the forecasts of generic nuclear power plant startups obtained from the EIA Middle Case electricity forecast. Sites are assigned to generic plants in chronological order according to startup date.

Method for assigning sites to projected generic nuclear power plants

International Nuclear Information System (INIS)

Holter, G.M.; Purcell, W.L.; Shutz, M.E.; Young, J.R.

1986-07-01

Pacific Northwest Laboratory developed a method for forecasting potential locations and startup sequences of nuclear power plants that will be required in the future but have not yet been specifically identified by electric utilities. Use of the method results in numerical ratings for potential nuclear power plant sites located in each of the 10 federal energy regions. The rating for each potential site is obtained from numerical factors assigned to each of 5 primary siting characteristics: (1) cooling water availability, (2) site land area, (3) power transmission land area, (4) proximity to metropolitan areas, and (5) utility plans for the site. The sequence of plant startups in each federal energy region is obtained by use of the numerical ratings and the forecasts of generic nuclear power plant startups obtained from the EIA Middle Case electricity forecast. Sites are assigned to generic plants in chronological order according to startup date

Locations of Combined Sewer Overflow Outfalls - US EPA Region 3

Science.gov (United States)

This data layer identifies the locations of Combined sewer overflow outfalls. Combined sewer systems are sewers that are designed to collect rainwater runoff, domestic sewage, and industrial wastewater in the same pipe. Most of the time, combined sewer systems transport all of their wastewater to a sewage treatment plant, where it is treated and then discharged to a water body. During periods of heavy rainfall or snowmelt, however, the wastewater volume in a combined sewer system can exceed the capacity of the sewer system or treatment plant. For this reason, combined sewer systems are designed to overflow occasionally and discharge excess untreated wastewater directly to nearby streams, rivers, or other water bodies. For further information visit: http://cfpub1.epa.gov/npdes/home.cfm?program_id=5

Locative media

CERN Document Server

Wilken, Rowan

2014-01-01

Not only is locative media one of the fastest growing areas in digital technology, but questions of location and location-awareness are increasingly central to our contemporary engagements with online and mobile media, and indeed media and culture generally. This volume is a comprehensive account of the various location-based technologies, services, applications, and cultures, as media, with an aim to identify, inventory, explore, and critique their cultural, economic, political, social, and policy dimensions internationally. In particular, the collection is organized around the perception that the growth of locative media gives rise to a number of crucial questions concerning the areas of culture, economy, and policy.

Molecular plant volatile communication.

Science.gov (United States)

Holopainen, Jarmo K; Blande, James D

2012-01-01

Plants produce a wide array of volatile organic compounds (VOCs) which have multiple functions as internal plant hormones (e.g., ethylene, methyl jasmonate and methyl salicylate), in communication with conspecific and heterospecific plants and in communication with organisms of second (herbivores and pollinators) and third (enemies of herbivores) trophic levels. Species specific VOCs normally repel polyphagous herbivores and those specialised on other plant species, but may attract specialist herbivores and their natural enemies, which use VOCs as host location cues. Attraction of predators and parasitoids by VOCs is considered an evolved indirect defence, whereby plants are able to indirectly reduce biotic stress caused by damaging herbivores. In this chapter we review these interactions where VOCs are known to play a crucial role. We then discuss the importance of volatile communication in self and nonself detection. VOCs are suggested to appear in soil ecosystems where distinction of own roots from neighbours roots is essential to optimise root growth, but limited evidence of above-ground plant self-recognition is available.

The undersea location of the Swedish Final Repository for reactor waste, SFR - human intrusion aspects

International Nuclear Information System (INIS)

Eng, T.

1989-01-01

The Swedish Final Repository for reactor waste, SFR, is built under the Baltic sea close to the Forsmark nuclear power plant. Sixty metres of rock cover the repository caverns under the seabed. The depth of the Baltic sea is about 5-6 m at this location. A human intrusion scenario that in normal inland locations has shown to be of great importance, is a well that is drilled through or in the close vicinity of the repository. Since the land uplift in the SFR area is about 6 mm/year the undersea location of SFR ensures that no well will be drilled at this location for a considerable time while the area is covered by the Baltic sea

Selection of facility location under environmental damage priority and using ELECTRE method.

Science.gov (United States)

Gundogdu, Ceren Erdin

2011-03-01

In the recent years, the environmental problems have reached to a vital extent, which is pushing the boundaries and far beyond daily evaluations. Industrial plants, the energy sources and uncontrolled release of pollutant gases (SO2, CO2 etc.) in the production stage have the greatest share in the occurrence of unfavorable environmental conditions. For this reason, the dimension of the problems that may arise in the production stage of industrial plants is directly related to the selection of facility location. In this study, geographical regions (a total of 7 regions) of our country have been analyzed in terms of environmental values based on their basins and the unfavorable environmental problems that are currently being experienced. Considered as such, with the directives of an expert group composed of nature scientists, the criteria and alternative areas are determined using the data gathered on ecosystem, basin characteristics, and land types. Since the primary goal is to keep the environmental damages at the minimum level, comprehensive definition of the problem is constructed by consultation of the expert group and the criteria are determined. Considering the fact that it will prevent the drawbacks generated by making decisions depending on certain stereotypes toa great extent, ELECTRE (Elimination and Choice Translating Reality English - Elimination Et Choix Traduisant la Realite) method is used to determine in which geographic region our country's industrial plants should be located.

Sporotrichosis in an unusual location - Case report*

Science.gov (United States)

Reis, Brisa Dondoni; Cobucci, Fernanda Oliveira; Zacaron, Luciana Helena; D'Acri, Antonio Macedo; Lima, Ricardo Barbosa; Martins, Carlos José

2015-01-01

Sporotrichosis is the most common subcutaneous mycosis. It is caused by the dimorphic fungus Sporothrix schenckii, and the infection is usually acquired by traumatic inoculation. We describe a case of sporotrichosis in an uncommon location with an unusual mode of transmission. A 49-year-old female patient who lived in an urban area of Rio de Janeiro presented with involvement of the left ear. No history of contact with soil, plants or animals was elicited. The suspected source of infection was a pair of handmade wooden earrings. The delay in the diagnosis and treatment resulted in higher morbidity, unsightly scarring and loss of ear lobe. PMID:26312682

Sporotrichosis in an unusual location--Case report.

Science.gov (United States)

Reis, Brisa Dondoni; Cobucci, Fernanda Oliveira; Zacaron, Luciana Helena; D'Acri, Antonio Macedo; Lima, Ricardo Barbosa; Martins, Carlos José

2015-01-01

Sporotrichosis is the most common subcutaneous mycosis. It is caused by the dimorphic fungus Sporothrix schenckii, and the infection is usually acquired by traumatic inoculation. We describe a case of sporotrichosis in an uncommon location with an unusual mode of transmission. A 49-year-old female patient who lived in an urban area of Rio de Janeiro presented with involvement of the left ear. No history of contact with soil, plants or animals was elicited. The suspected source of infection was a pair of handmade wooden earrings. The delay in the diagnosis and treatment resulted in higher morbidity, unsightly scarring and loss of ear lobe.

Tools for evaluating Lipolexis oregmae (Hymenoptera: Aphidiidae) in the field: Effects of host aphid and host plant on mummy location and color plus improved methods for obtaining adults

International Nuclear Information System (INIS)

Singh, R.; Hoy, M.A.

2007-01-01

Lipolexis oregmae Gahan was introduced into Florida in a classical biological control program directed against the brown citrus aphid, Toxoptera citricida (Kirkaldy), on citrus. Prior to evaluating distribution, host range, and potential nontarget effects of L. oregmae in Florida, we evaluated the role of other potential host aphids and host plants on mummy production and location. Under laboratory conditions, this parasitoid produced the most progeny on the target pest, the brown citrus aphid on citrus. This parasitoid, unlike the majority of aphidiids, did not produce mummies on any of the host plants tested when reared in black citrus aphid T. aurantii (Boyer de Fonscolombe) on grapefruit, spirea aphid Aphis spiraecola Patch on grapefruit and pittosporum, cowpea aphid A. craccivora Koch on grapefruit and cowpeas, or melon aphid A. gossypii Glover on grapefruit and cucumber. Thus, sampling for L. oregmae mummies of these host aphids and host plants must involve holding foliage in the laboratory until mummies are produced. This parasitoid requires high relative humidity to produce adults because no adults emerged when mummies were held in gelatin capsules, but high rates of emergence were observed when mummies were held on 1.5% agar plates. In addition, we compared the color of 6 aphid hosts and the color of mummies produced by L. oregmae when reared in them to determine if color of mummies could be used to identify L. oregmae . Mummy color varied between aphid hosts and tested host plants, and is not a useful tool for identifying L. oregmae for nontarget effects. (author) [es

U.S. Nuclear Power Reactor Plant Status

Data.gov (United States)

Nuclear Regulatory Commission — Demographic data on U.S. commercial nuclear power reactors, including: plant name/unit number, docket number, location, licensee, reactor/containment type, nuclear...

Location of Urban Logistic Terminals as Hub Location Problem

Directory of Open Access Journals (Sweden)

Jasmina Pašagić Škrinjar

2012-09-01

Full Text Available In this paper the problems of locating urban logistic terminals are studied as hub location problems that due to a large number of potential nodes in big cities belong to hard non-polynomial problems, the so-called NP-problems. The hub location problems have found wide application in physical planning of transport and telecommunication systems, especially systems of fast delivery, networks of logistic and distribution centres and cargo traffic terminals of the big cities, etc. The paper defines single and multiple allocations and studies the numerical examples. The capacitated single allocation hub location problems have been studied, with the provision of a mathematical model of selecting the location for the hubs on the network. The paper also presents the differences in the possibilities of implementing the exact and heuristic methods to solve the actual location problems of big dimensions i.e. hub problems of the big cities.

Laser-Induced Fluorescence (LIF) from plant foliage

Science.gov (United States)

Chappelle, Emmett W.; Williams, Darrel L.

1987-01-01

The fluorescence spectra and fluorescence induction kinetics of green plants excited at 337 nm by a laser were studied. They correlate with plant type, as well as with changes in the physiology of the plant as the result of stress. The plant types studied include herbaceous dicots, monocots, hardwoods, conifers, and algae. These plant types could be identified on the basis of differences in either the number of fluorescent bands or the relative intensity of the bands. Differences in fluorescent spectra which could be related to vigor status are observed in conifers located in an area of high atmospheric deposition. Changes in the fluorescence spectra and induction kinetics are also seen in plants grown under conditions of nutrient deficiency and drought stress.

Coal-Fired Power Plants, Region 9, 2011, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — Approximate locations of active coal-fired power plants located in US EPA's Region 9. Emission counts from the 2005 National Emissions Inventory (NEI) are included...

Cost regulation on the inspection of plants requiring supervision

International Nuclear Information System (INIS)

Anon.

1981-01-01

According to annexes I to VI of this regulation, TUeVs (technical control authorities) (2nd sentence of para. 1 of sect. 24 c of the trade law) collect fees for inspections ordered by the authorities for the following plants and installations: 1. steam boiler plants, 2. pressure vessels, high-pressure gas vessels, feeders, 3. lifts, 4. acetylene plants, 5. plants for the storage, racking and transport of combustile liquids, 6. electrical installations on hazardous location. (orig.) [de

Location of Bioelectricity Plants in the Madrid Community Based on Triticale Crop: A Multicriteria Methodology

Directory of Open Access Journals (Sweden)

L. Romero

2015-01-01

Full Text Available This paper presents a work whose objective is, first, to quantify the potential of the triticale biomass existing in each of the agricultural regions in the Madrid Community through a crop simulation model based on regression techniques and multiple correlation. Second, a methodology for defining which area has the best conditions for the installation of electricity plants from biomass has been described and applied. The study used a methodology based on compromise programming in a discrete multicriteria decision method (MDM context. To make a ranking, the following criteria were taken into account: biomass potential, electric power infrastructure, road networks, protected spaces, and urban nuclei surfaces. The results indicate that, in the case of the Madrid Community, the Campiña region is the most suitable for setting up plants powered by biomass. A minimum of 17,339.9 tons of triticale will be needed to satisfy the requirements of a 2.2 MW power plant. The minimum range of action for obtaining the biomass necessary in Campiña region would be 6.6 km around the municipality of Algete, based on Geographic Information Systems. The total biomass which could be made available in considering this range in this region would be 18,430.68 t.

Technical analysis of magneto-inductive crane cables in nuclear power plants. Application crane Cofrentes Nuclear Power Plant

International Nuclear Information System (INIS)

Gavilan Moreno, C. J.

2010-01-01

In 2009, the Cofrentes Nuclear Power Plant made a study about crane inspection techniques available on the market and other industries. The result was the location of the magneto-inductive technique inspection. Its use provides an objective assessment of the resistant section and; through these data; it could be made calculations as the maximum voltage allowed. Therefore, the technique is proven and available to all nuclear power plants.

ARSENIC REMOVAL FROM DRINKING WATER BY IRON REMOVAL PLANTS

Science.gov (United States)

This report documents a long term performance study of two iron removal water treatment plants to remove arsenic from drinking water sources. Performance information was collected from one system located in midwest for one full year and at the second system located in the farwest...

Wanted: Information on the Distribution of Cultivated Plants

Science.gov (United States)

Howard, Richard A.

1970-01-01

Lack of documentation makes it very difficult to discover where species of cultivated plants may be found in the United States. Plead for compilation of "campus floras and herbarium collections. Need for a rational locator file of available plant materials. Lists and reviews present sources of information. Bibliography of campus floras. (EB)

Forest resources, government policy, and investment location decisions of the forest products industry in the southern United States

Science.gov (United States)

Changyou Sun; Daowei Zhang

2010-01-01

In this article, the results of an initial attempt to estimate the effects of state attributes on plant location and investment expenditure were presented for the forest products industry in the southern United States. A conditional logit model was used to analyze new plant births, and a time-series cross-section model to assess the total capital expenditure....

Low speed turbines for nuclear power plants

International Nuclear Information System (INIS)

Ugol'nikov, V.V.; Kosyak, Yu.F.; Virchenko, M.A.

1975-01-01

Work of the Kharkov turbine plant on planning and manufacture for nuclear power plants of low-speed (1500 rpm) turbines with a power of 500-1000 MW is described. The selection of a construction diagram for the turbine assembly, determined basically by the presence or absence of parts of average pressure, is considered. Special construction features of the condenser and turbine are described. Turbine K-500, with a rate of 1500 rpm, was calculated for operation in a two-loop nuclear power plant with saturated steam with intermediate separation and two-stage steam regeneration. On the base of this turbine, three models of 1000-MW turbines were developed. The first model has a cylinder of average pressure (TsSD) and a lateral condenser. The second has no TsSD but a low location of the condensers. The third has no TsSD and the condensers are located laterally. Calculations of the heat efficiency of the three types of turbines showed that several advantages are offered by the model with a TsSD. Better aerodynamic properties of the exhaust nozzles and condensers with lateral location allows decreasing the specific heat consumption to 0.5-1% or, at the same power, a 10-20% decrease in cooling water consumption

Improvement of plant reliability in PT. Badak LNG plant

International Nuclear Information System (INIS)

Achmad, S.; Somantri, A.

1997-01-01

PT. Badak's LNG sales commitment has been steadily increasing, therefore, there has been more emphasis to improve and maintain the LNG plant reliability. From plant operation historical records, Badak LNG plant experienced a high number of LNG process train trips and down time for 1977 through 1988. The highest annual number of LNG plant trips (50 times) occurred in 1983 and the longest LNG process train down time (1259 train-hours) occurred in 1988. Since 1989, PT. Badak has been able to reduce the number of LNG process train trips and down time significantly. In 1994 the number of LNG process train trips and was 18 times and the longest LNG process train down time was 377 train-hours. This plant reliability improvement was achieved by implementing plant reliability improvement programs beginning with the design of the new facilities and continuing with the maintenance and modification of the existing facilities. To improve reliability of the existing facilities, PT. Badak has been implementing comprehensive maintenance programs, to reduce the frequency and down time of the plant, such as Preventive and Predictive Maintenance as well as procurement material improvement since PT. Badak location is in a remote area. By implementing the comprehensive reliability maintenance, PT. Badak has been able to reduce the LNG process train trips to 18 and down time to 337 train hours in 1994 with the subsequent maintenance cost reduction. The average PT. Badak plant availability from 1985 to 1995 is 94.59%. New facilities were designed according to the established PT. Badak design philosophy, master plan and specification. Design of new facilities was modified to avoid certain problems from past experience. (au)

Determination of {sup 90}Sr, {sup 63}Ni and {sup 55}Fe activities by liquid scintillation counting in the environmental samples close to French nuclear power plants located on Loire and Garonne rivers

Energy Technology Data Exchange (ETDEWEB)

Rousseau, G.; Mokili, M.B.; Le Roy, C.; Deniau, I. [SUBATECH, IN2P3 (France); Gontier, G.; Boyer, C. [EDF-DPI-DIN-CIDEN (France); Hemidy, P.Y. [EDF-DPN-UNIE-GPRE-IEV (France); Chardon, P. [CNRS/IN2P3 (France)

2014-07-01

The protection of the aquatic and terrestrial environment from a wide range of radioactive contaminants released by nuclear industry requires continuous monitoring of radionuclides released into the environment. Specific measurement methods depending of the radionuclide are used to determinate this contribution. A lot of radionuclide can easily be measured at low level by gamma spectrometry, like {sup 137}Cs, {sup 60}Co..., but others like {sup 90}Sr, {sup 63}Ni or {sup 55}Fe require prior specific radiochemical separations. Activity of {sup 90}Sr values in environmental samples are available but only few measurements of {sup 63}Ni and {sup 55}Fe activities have been carried out in samples collected in the environment close to French nuclear power plants located on the Loire and Garonne rivers despite they represent 12% to 24% for {sup 63}Ni activity and <1% for {sup 55}Fe + other minor radionuclides of total activity of their liquid effluent discharges. {sup 90}Sr is not rejected by the liquid effluent discharges of Nuclear Power Plants and can be found in the environmental samples because of thermonuclear test and subsequently after the Chernobyl nuclear power plant accident. Considering the French Nuclear Power Plant located on Loire and Garonne rivers, the determination of {sup 90}Sr, {sup 63}Ni and {sup 55}Fe levels in the environmental samples around French nuclear power plants is carried out to detect the traces of these radionuclides originating from nuclear technology activities. The environment around five French nuclear Power Plants was investigated for 4 years between 2009 and 2014. The radionuclide activities determined by liquid scintillation counting after chemical steps were performed on a large set of various matrix samples likely to be encountered in environmental monitoring as soils, sediments, terrestrial and aquatic bio-indicators. It was found that the mean activity concentration of the most frequently detected was for the radionuclide {sup 90

Location, location, location: does early cancer in Barrett's esophagus have a preference?

Science.gov (United States)

Enestvedt, Brintha K; Lugo, Ricardo; Guarner-Argente, Carlos; Shah, Pari; Falk, Gary W; Furth, Emma; Ginsberg, Gregory G

2013-09-01

Early cancer (high-grade dysplasia [HGD] and intramucosal carcinoma [ImCa]) associated with Barrett's esophagus (BE) may have a circumferential spatial predilection. To describe the esophageal circumferential location of early cancer in BE. Retrospective study, single tertiary referral center. One hundred nineteen patients were referred for endoscopic eradication therapy for early cancer associated with BE. Endoscopic images and reports and pathology were reviewed. Circumferential location designation of early cancer in BE by using a clock-face orientation. One hundred nineteen of 131 patients referred for endoscopic eradication therapy had a location designation for their advanced histology (91.9%). There were a total of 57 patients (47.9%) with HGD and 62 patients (52.1%) with ImCa. There was a significantly higher rate of early cancer (HGD or ImCa) in the right hemisphere (12 to 6 o'clock location) compared with the left hemisphere (84.9% vs 15.1%, P cancer was found in the 12 to 3 o'clock quadrant (64.7%); 71.9% of HGD and 58.1% of ImCa lesions were located in the 12 to 3 o'clock quadrant. Retrospective design, single center. Early cancer associated with BE is far more commonly found in the right hemisphere of the esophagus (12 to 6 o'clock) with the highest rate in the 12 to 3 o'clock quadrant. These findings support enhanced scrutiny of the right hemisphere of the esophagus during surveillance and endoscopic treatment of patients with BE. Copyright © 2013 American Society for Gastrointestinal Endoscopy. Published by Mosby, Inc. All rights reserved.

Experience with the use of SF6 to locate condenser leakage in power plants

International Nuclear Information System (INIS)

Tondi, D.M.

1988-01-01

Condenser tube water inleakage is a prime source of contamination in power plant steam systems. Conventional techniques of leaking-tube detection require periods of reduced power operation. A new method, using sulfur hexafluoride as a tracer gas, can detect leaking tubes while the plant is operating. Sulfur hexafluoride is a gas that when entrained in the cooling water will follow the water through the leak, be volatilized by the vacuum and heat in the condenser, and be detected in the off-gas. The technique will provide positive identification of a leaking waterbox. Sulfur hexafluoride is innocuous, insoluble, thermally stable, and non-toxic. Its most important characteristic in this application is that it can be detected in very low concentration. This high sensitivity enables waterbox testing to be performed while the unit is on line and at full power. The technique has been used at more than 30 fossil and nuclear stations. Tests show that leaking waterboxes can be isolated, and that leaks of less than one gallon per day are readily detectable. There are several cost benefits associated with this technology. One which can be quantified is the cost for replacement power. The process of reducing power in order to silate a leaking waterbox can cost in excess of 30,000 dollars for even a small unit. In addition to direct cost savings, water chemistry can be improved since sensitivity to leakage is generally greater than station chemistry capabilities. Test results from service work at a range of typical plants will be discussed including: estimations of detected leak rates, injection points and rates, and approximately cost savings

Plant Research Department annual report 2003

DEFF Research Database (Denmark)

Kossmann, J.; Jakobsen, Iver; Nielsen, K.K.

2004-01-01

In 2003 the Plant Research Department (PRD) at Risø National Laboratory was involved in establishing the consortium Plant Biotech Denmark, which is unifying most of the Danish Plant Biotechnology activities. Within the consortium, PRD has the uniqueopportunity to be the only life science department...... to genes, which are widely applicable in the life sciences, such as non-invasive and non-destructive technologies to determine metabolite concentrationswith high spatial and temporal resolution. The Plant Research Department applies these and state-of-the-art technologies to increase knowledge to develop...... located in an environment that is largely dominated by physicists. PRD is challenged to optimally interface Plant Biology with the different fields of expertise that are established at Risø NationalLaboratory. These activities are mainly related to develop novel post-genomic tools to assign function...

Hydroelectric Power Plants Dobsina

International Nuclear Information System (INIS)

Majercak, V.; Srenkelova, Z.; Kristak, J.G.

1997-01-01

In this brochure the Hydroelectric Power Plants Dobsina, (VED), subsidiary of the utility Slovenske Elektrarne, a.s. (Slovak Electric, plc. Bratislava) are presented. VED is mainly aimed at generating peak-load electrical energy and maintenance of operational equipment. Reaching its goals, company is first of all focused on reliability of production, economy and effectiveness, keeping principles of work safety and industry safety standards and also ecology. VED operates eight hydroelectric power plants, from which PVE Ruzin I and PVE Dobsina I are pump storage ones and they are controlled directly by the Slovak Energy Dispatch Centre located in Zilina thought the system LS 3200. Those power plants participate in secondary regulation of electrical network of Slovakia. They are used to compensate balance in reference to foreign electrical networks and they are put into operation independently from VED. Activity of the branch is focused mainly on support of fulfilment of such an important aim as electric network regulation. Beginnings of the subsidiary Hydroelectric Power Plants Dobsina are related to the year of 1948. After commissioning of the pump storage Hydroelectric Power Plants Dobsina in 1953, the plant started to carry out its mission. Since that time the subsidiary has been enlarged by other seven power plants, through which it is fulfilling its missions nowadays. The characteristics of these hydroelectric power plants (The pump-storage power plant Dobsina, Small hydroelectric power plant Dobsina II, Small hydroelectric power plant Rakovec, Small hydroelectric power plant Svedlar, Hydroelectric power plant Domasa, The pump-storage power plant Ruzin, and Small hydroelectric power plant Krompachy) are described in detail. Employees welfare and public relations are presented

Environmental monitoring of fluoride emissions using precipitation, dust, plant and soil samples

International Nuclear Information System (INIS)

Franzaring, J.; Hrenn, H.; Schumm, C.; Klumpp, A.; Fangmeier, A.

2006-01-01

A pollution gradient was observed in precipitation, plants and soils sampled at different locations around a fluoride producing chemical plant in Germany. In all samples the influence of emissions was discernible up to a distance of 500 m from the plant. However, fluoride concentrations in plant bioindicators (leaves of birch and black berry) and in bulk precipitation showed a more pronounced relationship with the distance from the source than fluoride concentrations in soil. Vegetables sampled in the vicinity of the plant also had elevated concentrations of fluoride, but only the consumption of larger quantities of this material would lead to exceedances of recommended daily F-intake. The present study did not indicate the existence of low phytotoxicity thresholds for fluoride in the plant species used in the study. Even at very high fluoride concentrations in leaf tissue (963 ppm) plants did not show injury due to HF. Dust sampling downwind of the chemical plant confirmed that particulate fluoride was of minor importance in the study area. - A pronounced pollution gradient was observed in precipitation, plants and soils sampled at different locations around a fluoride emitting chemical plant in Germany

Thermal power plant efficiency enhancement with Ocean Thermal Energy Conversion

International Nuclear Information System (INIS)

Soto, Rodrigo; Vergara, Julio

2014-01-01

In addition to greenhouse gas emissions, coastal thermal power plants would gain further opposition due to their heat rejection distressing the local ecosystem. Therefore, these plants need to enhance their thermal efficiency while reducing their environmental offense. In this study, a hybrid plant based on the principle of Ocean Thermal Energy Conversion was coupled to a 740 MW coal-fired power plant project located at latitude 28°S where the surface to deepwater temperature difference would not suffice for regular OTEC plants. This paper presents the thermodynamical model to assess the overall efficiency gained by adopting an ammonia Rankine cycle plus a desalinating unit, heated by the power plant condenser discharge and refrigerated by cold deep seawater. The simulation allowed us to optimize a system that would finally enhance the plant power output by 25–37 MW, depending on the season, without added emissions while reducing dramatically the water temperature at discharge and also desalinating up to 5.8 million tons per year. The supplemental equipment was sized and the specific emissions reduction was estimated. We believe that this approach would improve the acceptability of thermal and nuclear power plant projects regardless of the plant location. -- Highlights: • An Ocean Thermal Energy Conversion hybrid plant was designed. • The waste heat of a power plant was delivered as an OTEC heat source. • The effect of size and operating conditions on plant efficiency were studied. • The OTEC implementation in a Chilean thermal power plant was evaluated. • The net efficiency of the thermal power plant was increased by 1.3%

Membrane Targeting of P-type ATPases in Plant Cells

International Nuclear Information System (INIS)

Harper, Jeffrey F.

2004-01-01

How membrane proteins are targeted to specific subcellular locations is a very complex and poorly understood area of research. Our long-term goal is to use P-type ATPases (ion pumps), in a model plant system Arabidopsis, as a paradigm to understand how members of a family of closely related membrane proteins can be targeted to different subcellular locations. The research is divided into two specific aims. The first aim is focused on determining the targeting destination of all 10 ACA-type calcium pumps (Arabidopsis Calcium ATPase) in Arabidopsis. ACAs represent a plant specific-subfamily of plasma membrane-type calcium pumps. In contrast to animals, the plant homologs have been found in multiple membrane systems, including the ER (ACA2), tonoplast (ACA4) and plasma membrane (ACA8). Their high degree of similarity provides a unique opportunity to use a comparative approach to delineate the membrane specific targeting information for each pump. One hypothesis to be tested is that an endomembrane located ACA can be re-directed to the plasma membrane by including targeting information from a plasma membrane isoform, ACA8. Our approach is to engineer domain swaps between pumps and monitor the targeting of chimeric proteins in plant cells using a Green Fluorescence Protein (GFP) as a tag. The second aim is to test the hypothesis that heterologous transporters can be engineered into plants and targeted to the plasma membrane by fusing them to a plasma membrane proton pump. As a test case we are evaluating the targeting properties of fusions made between a yeast sodium/proton exchanger (Sod2) and a proton pump (AHA2). This fusion may potentially lead to a new strategy for engineering salt resistant plants. Together these aims are designed to provide fundamental insights into the biogenesis and function of plant cell membrane systems

Insights into location dependent loss-of-coolant-accident (LOCA) frequency assessment for GSI-191 risk-informed applications

Energy Technology Data Exchange (ETDEWEB)

Fleming, K.N., E-mail: KarlFleming@comcast.net [KNF Consulting LLC, Spokane, WA (United States); Lydell, B.O.Y. [SIGMA-PHASE INC., Vail, AZ (United States)

2016-08-15

Highlights: • Role of operating experience in loss-of-coolant-accident (LOCA) frequency assessment. • Plant-to-plant variability in calculated LOCA frequency. • Frequency of double-ended-guillotine-break (DEGB). • Uncertainties in LOCA frequencies. • Risk management insights. - Abstract: As a tribute to the published work by S.H. Bush, S. Beliczey and H. Schulz, this paper assesses the progress with methods and techniques for quantifying the reliability of piping systems in commercial nuclear power plants on the basis of failure rate estimates derived from field experience data in combination with insights and results from probabilistic fracture mechanics analyses and expert elicitation exercises. This status assessment is made from a technical perspective obtained through development of location-specific loss-of-coolant-accident (LOCA) frequencies for input to risk-informed resolution of the generic safety issue (GSI) 191. The methods and techniques on which these GSI-191 applications are based build on a body of work developed by the authors during a period spanning more than two decades. The insights that are presented and discussed in this paper cover today’s knowledge base concerning how to utilize a risk-informed approach to the assessment of piping reliability in the context of probabilistic risk assessment (PRA) in general and the resolution of GSI-191 in particular. Specifically the paper addresses the extent to which LOCA frequencies vary from location to location within a reactor coolant system pressure boundary (RCPB) for a given plant as well as vary from plant to plant, and the reasons for these variabilities. Furthermore, the paper provides the authors’ perspectives on interpretations and applications of information extracted from an expert elicitation process to obtain LOCA frequencies as documented in NUREG-1829 and how to apply this information to GSI-191. Finally, this paper documents technical insights relative to mitigation of

Insights into location dependent loss-of-coolant-accident (LOCA) frequency assessment for GSI-191 risk-informed applications

International Nuclear Information System (INIS)

Fleming, K.N.; Lydell, B.O.Y.

2016-01-01

Highlights: • Role of operating experience in loss-of-coolant-accident (LOCA) frequency assessment. • Plant-to-plant variability in calculated LOCA frequency. • Frequency of double-ended-guillotine-break (DEGB). • Uncertainties in LOCA frequencies. • Risk management insights. - Abstract: As a tribute to the published work by S.H. Bush, S. Beliczey and H. Schulz, this paper assesses the progress with methods and techniques for quantifying the reliability of piping systems in commercial nuclear power plants on the basis of failure rate estimates derived from field experience data in combination with insights and results from probabilistic fracture mechanics analyses and expert elicitation exercises. This status assessment is made from a technical perspective obtained through development of location-specific loss-of-coolant-accident (LOCA) frequencies for input to risk-informed resolution of the generic safety issue (GSI) 191. The methods and techniques on which these GSI-191 applications are based build on a body of work developed by the authors during a period spanning more than two decades. The insights that are presented and discussed in this paper cover today’s knowledge base concerning how to utilize a risk-informed approach to the assessment of piping reliability in the context of probabilistic risk assessment (PRA) in general and the resolution of GSI-191 in particular. Specifically the paper addresses the extent to which LOCA frequencies vary from location to location within a reactor coolant system pressure boundary (RCPB) for a given plant as well as vary from plant to plant, and the reasons for these variabilities. Furthermore, the paper provides the authors’ perspectives on interpretations and applications of information extracted from an expert elicitation process to obtain LOCA frequencies as documented in NUREG-1829 and how to apply this information to GSI-191. Finally, this paper documents technical insights relative to mitigation of

Is Impatiens balsamina a qualitative short-day plant?

Directory of Open Access Journals (Sweden)

Elżbieta Teske

2014-01-01

Full Text Available Impatiens balsamina which, in literature on the physiology of flowering, is assigned to qualitative short-day plants, flowers under Polish climatic conditions from June until September. It flowers, therefore. during the period of the longest day. The photoperiodic responses of I. balsamina plants raised from seeds obtained from botanical gardens located within the range of 23 -65° N. lat. were studied. The experiment revealed marked differences in the photoperiodic responses within the species. Qualitative short-day plants, quantitative short-day plants and day-neutral plants were found in the studied material. An evident correlation was found between the place of origin of the studied seeds and the photoperiodic sensitivity of the plants raised from them.

Regulation of Water Balance of the Plant from the Different Geo-Environmental Locations

OpenAIRE

Astghik R. Sukiasyan

2016-01-01

Under the drought stress condition, the plants would grow slower. Temperature is one of the most important abiotic factors which suppress the germination processes. However, the processes of transpiration are regulated directly by the cell water, which followed to an increase in volume of vacuoles. During stretching under the influence of water pressure, the cell goes into the state of turgor. In our experiments, lines of the semi-dental sweet maize of Armenian population from various zones o...

Radionuclides in the ground at the Savannah River Plant

International Nuclear Information System (INIS)

Fenimore, J.W.; Horton, J.H. Jr.

1974-01-01

Savannah River Plant operations have dispersed radionuclides into the ground at more than 25 locations on the plant-site. At some sites decay and natural dispersal processes have reduced the concentration below detectable levels. Other sites will require continuous surveillance and restricted use. The purpose of this report is to tabulate the location of these sites and summarize the data collected from them so that these data will be readily available for future reference and guidance in evaluating and managing these sites. A description of each site and its condition during 1972 is attached. 1 fig

High-Throughput Analysis of T-DNA Location and Structure Using Sequence Capture.

Science.gov (United States)

Inagaki, Soichi; Henry, Isabelle M; Lieberman, Meric C; Comai, Luca

2015-01-01

Agrobacterium-mediated transformation of plants with T-DNA is used both to introduce transgenes and for mutagenesis. Conventional approaches used to identify the genomic location and the structure of the inserted T-DNA are laborious and high-throughput methods using next-generation sequencing are being developed to address these problems. Here, we present a cost-effective approach that uses sequence capture targeted to the T-DNA borders to select genomic DNA fragments containing T-DNA-genome junctions, followed by Illumina sequencing to determine the location and junction structure of T-DNA insertions. Multiple probes can be mixed so that transgenic lines transformed with different T-DNA types can be processed simultaneously, using a simple, index-based pooling approach. We also developed a simple bioinformatic tool to find sequence read pairs that span the junction between the genome and T-DNA or any foreign DNA. We analyzed 29 transgenic lines of Arabidopsis thaliana, each containing inserts from 4 different T-DNA vectors. We determined the location of T-DNA insertions in 22 lines, 4 of which carried multiple insertion sites. Additionally, our analysis uncovered a high frequency of unconventional and complex T-DNA insertions, highlighting the needs for high-throughput methods for T-DNA localization and structural characterization. Transgene insertion events have to be fully characterized prior to use as commercial products. Our method greatly facilitates the first step of this characterization of transgenic plants by providing an efficient screen for the selection of promising lines.

Temporal dynamics of soil nematode communities in a grassland plant diversity experiment.

NARCIS (Netherlands)

Viketoft, M.; Sohlenius, B.; Bostrom, S.; Palmborg, C.; Bengtsson, J.; Berg, M.P.; Kuss-Danell, K.

2011-01-01

We report here on an 8-year study examining links between plant and nematode communities in a grassland plant diversity experiment, located in the north of Sweden on previous agricultural soil. The examined plots contained 1, 4 and 12 common grassland plant species from three functional groups;

Buzz in Paris: flower production and plant-pollinator interactions in plants from contrasted urban and rural origins.

Science.gov (United States)

Desaegher, James; Nadot, Sophie; Dajoz, Isabelle; Colas, Bruno

2017-12-01

Urbanisation, associated with habitat fragmentation, affects pollinator communities and insect foraging behaviour. These biotic changes are likely to select for modified traits in insect-pollinated plants from urban populations compared to rural populations. To test this hypothesis, we conducted an experiment involving four plant species commonly found in both urban and rural landscapes of the Île-de-France region (France): Cymbalaria muralis, Geranium robertianum, Geum urbanum and Prunella vulgaris. The four species were grown in four urban and four rural experimental sites in 2015. For each species and each experimental site, plants were grown from seeds collected in five urban and five rural locations. During flowering, we observed flower production and insect-flower interactions during 14 weeks and tested for the effects of experimental site location and plant origin on flower production and on the number of floral visits. The study species had various flower morphology and hence were visited by different floral visitors. The effect of experimental sites and seed origin also varied among study species. We found that (1) insect visits on P. vulgaris were more frequent in rural than in urban sites; (2) for C. muralis, the slope relating the number of pollinator visits to the number of flowers per individual was steeper in urban versus rural sites, suggesting a greater benefit in allocating resources to flower production in urban conditions; (3) as a likely consequence, C. muralis tended to produce more flowers in plants from urban versus rural origin.

Selection of sites for nuclear power plants in The Netherlands. Pt. A

International Nuclear Information System (INIS)

1985-01-01

In this report a policy proposal is presented concerning the selection of location sites for new nuclear power plants in the Netherlands. Firstly it is investigated which of the 29 already selected location sites are not to be taken into further account because of obvious obstructions (close vicinity of a big city etc.). The remaining sites are judged on the base of local population magnitude. The sites that pass the last criteria are relatively compared from a large number of viewpoints. To round off the selection procedure the government will explain why they consider the finally selected sites to be suitable for location of new nuclear power plants. Steps are indicated to prevent the decrease of planologic suitability of the selected location sites. (Auth.)

Determining potential locations for biomass valorization using a macro screening approach

Energy Technology Data Exchange (ETDEWEB)

Van Dael, M.; Van Passel, S.; Schreurs, E. [Research Group of Environmental Economics, Centre for Environmental Sciences, Hasselt University, Agoralaan Gebouw D, 3590 Diepenbeek (Belgium); Pelkmans, L.; Guisson, R. [VITO, Boeretang 200, 2400 Mol (Belgium); Swinnen, G. [Research Group of Marketing, Hasselt University, Agoralaan Gebouw D, 3590 Diepenbeek (Belgium)

2012-10-15

European policy states that by 2020 at least 20% of final energy consumption should come from renewable energy sources. Biomass as a renewable energy source cannot be disregarded in order to attain this target. In this study a macro screening approach is developed to determine potential locations for biomass valorization in a specified region. The approach consists of five steps: (1) criteria determination, (2) data gathering, (3) weight assignment, (4) final score, (5) spatial representation. The resulting outcome provides a first well balanced scan of the possibilities for energy production using regional biomass. This way policy makers and investors can be supported and motivated to study the possibilities of building energy production plants at specific locations in more detail, which can be described as a 'micro-screening'. In our case study the approach is applied to determine the potentially interesting locations to establish a biomass project. The region has been limited to the forty-four communities in the province of Limburg (Belgium). The macro screening approach has shown to be very effective since the amount of interesting locations has been reduced drastically.

Ethnobotanical investigation of 'wild' food plants used by rice farmers in Kalasin, Northeast Thailand

Directory of Open Access Journals (Sweden)

Cruz-Garcia Gisella S

2011-11-01

Full Text Available Abstract Background Wild food plants are a critical component in the subsistence system of rice farmers in Northeast Thailand. One of the important characteristics of wild plant foods among farming households is that the main collection locations are increasingly from anthropogenic ecosystems such as agricultural areas rather than pristine ecosystems. This paper provides selected results from a study of wild food conducted in several villages in Northeast Thailand. A complete botanical inventory of wild food plants from these communities and surrounding areas is provided including their diversity of growth forms, the different anthropogenic locations were these species grow and the multiplicity of uses they have. Methods Data was collected using focus groups and key informant interviews with women locally recognized as knowledgeable about contemporarily gathered plants. Plant species were identified by local taxonomists. Results A total of 87 wild food plants, belonging to 47 families were reported, mainly trees, herbs (terrestrial and aquatic and climbers. Rice fields constitute the most important growth location where 70% of the plants are found, followed by secondary woody areas and home gardens. The majority of species (80% can be found in multiple growth locations, which is partly explained by villagers moving selected species from one place to another and engaging in different degrees of management. Wild food plants have multiple edible parts varying from reproductive structures to vegetative organs. More than two thirds of species are reported as having diverse additional uses and more than half of them are also regarded as medicine. Conclusions This study shows the remarkable importance of anthropogenic areas in providing wild food plants. This is reflected in the great diversity of species found, contributing to the food and nutritional security of rice farmers in Northeast Thailand.

Nuclear dual-purpose plants for industrial energy

International Nuclear Information System (INIS)

Klepper, O.H.

1976-01-01

One of the major obstacles to extensive application of nuclear power to industrial heat is the difference between the relatively small energy requirements of individual industrial plants and the large thermal capacity of current power reactors. A practical way of overcoming this obstacle would be to operate a centrally located dual-purpose power plant that would furnish process steam to a cluster of industrial plants, in addition to generating electrical power. The present study indicates that even relatively remote industrial plants could be served by the power plant, since it might be possible to convey steam economically as much as ten miles or more. A survey of five major industries indicates a major potential market for industrial steam from large nuclear power stations

Protection of warehouses and plants under capacity constraint

International Nuclear Information System (INIS)

Bricha, Naji; Nourelfath, Mustapha

2015-01-01

While warehouses may be subjected to less protection effort than plants, their unavailability may have substantial impact on the supply chain performance. This paper presents a method for protection of plants and warehouses against intentional attacks in the context of the capacitated plant and warehouses location and capacity acquisition problem. A non-cooperative two-period game is developed to find the equilibrium solution and the optimal defender strategy under capacity constraints. The defender invests in the first period to minimize the expected damage and the attacker moves in the second period to maximize the expected damage. Extra-capacity of neighboring functional plants and warehouses is used after attacks, to satisfy all customers demand and to avoid the backorders. The contest success function is used to evaluate success probability of an attack of plants and warehouses. A numerical example is presented to illustrate an application of the model. The defender strategy obtained by our model is compared to the case where warehouses are subjected to less protection effort than the plants. This comparison allows us to measure how much our method is better, and illustrates the effect of direct investments in protection and indirect protection by warehouse extra-capacities to reduce the expected damage. - Highlights: • Protection of warehouses and plants against intentional attacks. • Capacitated plant and warehouse location and capacity acquisition problem. • A non-cooperative two-period game between the defender and the attacker. • A method to evaluate the utilities and determine the optimal defender strategy. • Using warehouse extra-capacities to reduce the expected damage

Users' guide for a personal-computer-based nuclear power plant fire data base

International Nuclear Information System (INIS)

Wheelis, W.T.

1986-08-01

The Nuclear Power Plant Fire Data Base has been developed for use with an IBM XT (or with a compatible system). Nuclear power plant fire data is located in many diverse references, making it both costly and time-consuming to obtain. The purpose of this Fire Data Base is to collect and to make easily accessible nuclear power plant fire data. This users' guide discusses in depth the specific features and capabilities of the various options found in the data base. Capabilities include the ability to search several database fields simultaneously to meet user-defined conditions, display basic plant information, and determine the operating experience (in years) for several nuclear power plant locations. Step-by-step examples are included for each option to allow the user to learn how to access the data

Solar Power Plants: Dark Horse in the Energy Stable

Science.gov (United States)

Caputo, Richard S.

1977-01-01

Twelfth in a series of reports on solar energy, this article provides information relating to the following questions: (1) economic cost of solar-thermal-electric central power plants; (2) cost comparison with nuclear or coal plants; (3) locations of this energy source; and (4) its use and social costs. (CS)

Source water quality shaping different fouling scenarios in a full-scale desalination plant at the Red Sea

KAUST Repository

Khan, Muhammad; Manes, Carmem Lara De O; Aubry, Cyril; Croue, Jean-Philippe

2013-01-01

produced at a seawater RO desalination plant installed on a floating mobile barge. The plant was moved along the coastline of the Red Sea in Saudi Arabia. The two locations where the barge was anchored showed different water quality. At the second location

Sample investigation of the effects of smoke in the countryside by applying a modified planting procedure

Energy Technology Data Exchange (ETDEWEB)

Schoenbeck, H

1963-01-01

Plant damage due to factory fumes is described and the method of analysis presented. The leaves are damaged, and the plants do not develop fully. The distribution of SO/sub 2/ damage in the vicinity of a factory processing lead and zinc is detailed. Gas and soil samples were taken at various locations around the plant. In order to determine the effect of only the gases on plant growth, bush leaves, oats, wheat and sugar beets were grown in test locations under identical conditions, with and without factory fumes. The plants, leaves and beans exposed to fumes were only about 58% or less the size of plants not exposed to fumes. It is speculated that metal particles in the air also affect plant growth. 6 figures.

A new location to split Cre recombinase for protein fragment complementation.

Science.gov (United States)

Rajaee, Maryam; Ow, David W

2017-11-01

We have previously described a recombinase-mediated gene stacking system in which the Cre recombinase is used to remove lox-site flanked DNA no longer needed after each round of Bxb1 integrase-mediated site-specific integration. The Cre recombinase can be conveniently introduced by hybridization with a cre-expressing plant. However, maintaining an efficient cre-expressing line over many generations can be a problem, as high production of this DNA-binding protein might interfere with normal chromosome activities. To counter this selection against high Cre activity, we considered a split-cre approach, in which Cre activity is reconstituted after separate parts of Cre are brought into the same genome by hybridization. To insure that the recombinase-mediated gene stacking system retains its freedom to operate, we tested for new locations to split Cre into complementing fragments. In this study, we describe testing four new locations for splitting the Cre recombinase for protein fragment complementation and show that the two fragments of Cre split between Lys244 and Asn245 can reconstitute activity that is comparable to that of wild-type Cre. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Sites and social assessment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Nemoto, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1977-09-01

The sites of nuclear power plants in Japan have two features, first the extreme expectation for regional development because of the selection of depopulated districts for most locations, and the second, apprehensions of local people for two reasons of nuclear power generating techniques which do not plant the roots in society and handling of radioactive materials. In order to cope with these problems, it is necessary to consider that the development plan of the regions around reactor sites must be compiled systematically. Its premise is the ''social assessment'' which estimates the economical and social influences and evaluates the merit and demerit of nuclear power plants prior to the construction. This is of course inevitable. The objects of the assessment may be divided as follows: the human effect to individuals, the institutional effect to local community, the economical effect to region, and the national influence to the whole country. While the developmental action of locations includes the stages of examination, planning, construction and operation, and three location patterns are recognized according to the emphasized function, the improvement of national economy, upgrading of environmental quality, and the most priority in local welfare. In the process of the assessment, the following items may be taken notice that each item requires sometimes the weighting; the pattern to abandon location may exist; positive and negative effects are required to be distributed evenly in a triangle having the apexes each representing one of the above three patterns.

Identification of optimum outfall location for desalination plant in the coastal waters off Tuticorin, India

Digital Repository Service at National Institute of Oceanography (India)

DineshKumar, P.K.; NaveenKumar, K.R.; Muraleedharan, K.R.

Behaviour of the dilution characteristics of the coastal waters off Tuticorin is presented in the background of setting up of a desalination plant. Simulations of dispersion and spreading of the proposed discharges has been carried out. Scenarios...

Herbivore-induced plant volatiles and tritrophic interactions across spatial scales

NARCIS (Netherlands)

Aartsma, Y.S.Y.; Bianchi, F.J.J.A.; Werf, van der W.; Poelman, E.H.; Dicke, M.

2017-01-01

Herbivore-induced plant volatiles (HIPVs) are an important cue used in herbivore location by carnivorous arthropods such as parasitoids. The effects of plant volatiles on parasitoids have been well characterised at small spatial scales, but little research has been done on their effects at larger

Multi criteria decision making methods for location selection of distribution centers

Directory of Open Access Journals (Sweden)

Romita Chakraborty

2013-10-01

Full Text Available In recent years, major challenges such as, increase in inflexible consumer demands and to improve the competitive advantage, it has become necessary for various industrial organizations all over the world to focus on strategies that will help them achieve cost reduction, continual quality improvement, increased customer satisfaction and on time delivery performance. As a result, selection of the most suitable and optimal facility location for a new organization or expansion of an existing location is one of the most important strategic issues, required to fulfill all of these above mentioned objectives. In order to sustain in the global competitive market of 21st century, many industrial organizations have begun to concentrate on the proper selection of the plant site or best facility location. The best location is that which results in higher economic benefits through increased productivity and good distribution network. When a choice is to be made from among several alternative facility locations, it is necessary to compare their performance characteristics in a decisive way. As the facility location selection problem involves multiple conflicting criteria and a finite set of potential candidate alternatives, different multi-criteria decision-making (MCDM methods can be effectively applied to solve such type of problem. In this paper, four well known MCDM methods have been applied on a facility location selection problem and their relative ranking performances are compared. Because of disagreement in the ranks obtained by the four different MCDM methods a final ranking method based on REGIME has been proposed by the authors to facilitate the decision making process.

Cesium and potassium uptake by plants from soils

International Nuclear Information System (INIS)

Schaller, G.; Leising, C.; Krestel, R.; Wirth, E.

1990-11-01

The aim of the investigation was the reliable estimation of the Cs-137 root uptake by agricultural crops using the 'observed ratio model' (OR model) for the determination of transfer factors: Cs (plant)/K (plant) = OR x Cs (soil)/K (soil). For model validation representative soil (arable land, grass land, organic substrates from forests and peat) and plant samples from Bavaria were taken. These 4 parameters varied within a sufficiently wide range. In addition some samples from forest sites were taken. Soil and plant samples were taken at the same locations within 1 m 2 . (orig./HP) [de

Effect of increased renewables generation on operation of thermal power plants

International Nuclear Information System (INIS)

Eser, Patrick; Singh, Antriksh; Chokani, Ndaona; Abhari, Reza S.

2016-01-01

Highlights: • Impacts of increased renewables in central European transmission system are assessed. • Individual transmission lines and power plants of transmission system are modelled. • Starts and ramps of thermal power plants significantly increase with increased renewables. • Impact of renewables on thermal power plants is highly dependent on location. - Abstract: High spatial and temporal resolution optimal power flow simulations of the 2013 and 2020 interconnected grid in Central Western and Eastern Europe regions are undertaken to assess the impact of an increased penetration of renewables on thermal power plants. In contrast to prior studies, the present work models each individual transmission line and power plant within the two regions. Furthermore, for conventional plants, electricity costs are determined with respect to fuel type, nameplate capacity, operating condition and geographic location; cycling costs are modeled as function of the recent operational history. For renewable power plants, costs and available power are determined using mesoscale weather simulations and hydrology models. Countrywide validation of the simulations shows that all renewable and most conventional power production is predicted with less than 10% error. It is shown that the increased penetration of renewables in 2020 will induce a 4–23% increase in the number of starts of conventional plants. The number of load ramps significantly increases by 63–181%, which underlines the necessity for equipment manufacturers and utilities to adapt to scenarios of high penetration of renewables. The increased cycling operation of coal plants is shown to depend strongly on the power plant’s location and is mainly observed in Germany and the Czech Republic. Austrian coal plants are cycled less because they supply more base load power to southern Germany, where several nuclear power plants will be phased out by 2020. Thus there is a need for more transmission capacity along

Moisture, plant-plant interactions and herbivory as drivers of rangeland restoration success in the western US

Science.gov (United States)

Restoration efforts in the western US occur across a diverse array of plant communities and climatic conditions. Restoration is likely constrained by different factors in different locations, but few efforts have compared the outcomes of rangeland restoration experiments across broad spatial scales....

Atmospheric transformation of plant volatiles disrupts host plant finding

Science.gov (United States)

Li, Tao; Blande, James D.; Holopainen, Jarmo K.

2016-09-01

Plant-emitted volatile organic compounds (VOCs) play important roles in plant-insect interactions. Atmospheric pollutants such as ozone (O3) can react with VOCs and affect the dynamics and fidelity of these interactions. However, the effects of atmospheric degradation of plant VOCs on plant-insect interactions remains understudied. We used a system comprising Brassica oleracea subsp. capitata (cabbage) and the specialist herbivore Plutella xylostella to test whether O3-triggered VOC degradation disturbs larval host orientation, and to investigate the underlying mechanisms. Larvae oriented towards both constitutive and larva-induced cabbage VOC blends, the latter being the more attractive. Such behaviour was, however, dramatically reduced in O3-polluted environments. Mechanistically, O3 rapidly degraded VOCs with the magnitude of degradation increasing with O3 levels. Furthermore, we used Teflon filters to collect VOCs and their reaction products, which were used as odour sources in behavioural tests. Larvae avoided filters exposed to O3-transformed VOCs and spent less time searching on them compared to filters exposed to original VOCs, which suggests that some degradation products may have repellent properties. Our study clearly demonstrates that oxidizing pollutants in the atmosphere can interfere with insect host location, and highlights the need to address their broader impacts when evaluating the ecological significance of VOC-mediated interactions.

Safety regulation KTA 3901: Communication systems for nuclear power plants

International Nuclear Information System (INIS)

1981-01-01

The regulation applies to communication systems in stationary nuclear power plants with at least one power plant unit, i.e. alarm systems, staff locator systems, communicators, and systems for external communication. The regulation determines the type and extent of staff communication systems as well as the demands to be made on layout, installation, operating systems, and testing of communication systems for nuclear power plants. (orig./HP) [de

Changes in attitude structure toward nuclear power in the nuclear power plant locations of Tohoku district

International Nuclear Information System (INIS)

Tsujikawa, Norifumi; Tsuchida, Shoji; Shiotani, Takamasa; Nakagawa, Yuri

2012-01-01

This survey was examined the changes in structure of attitude toward nuclear power and the influence of environmental value on the attitude structure before and after the accident at the Fukushima No. 1 nuclear power plant. With residents of Aomori, Miyagi, and Fukushima prefectures as participants, we conducted online surveys in November 2009 and October 2011. Comparing the results before and after the accident, we found that trust in the management of nuclear power plants had a stronger influence on the perceived risk and benefit regarding nuclear power after the accident than before the accident. The value of concern about environmental destruction resulted in reduced trust in the management. (author)

Nuclear Power Plants in the World

International Nuclear Information System (INIS)

2000-01-01

The Japan Atomic Industrial Forum (JAIF) used every year to summarize a trend survey on the private nuclear power plants in the world in a shape of the 'Developmental trends on nuclear power plants in the world'. In this report, some data at the end of 1999 was made up on bases of answers on questionnaires from 72 electric companies in 31 nations and regions in the world by JAIF. This report is comprised of 19 items, and contains generating capacity of the plants; current status of Japan; trends of generating capacity of operating the plants, the plant orders and generating capacity of the plants; world nuclear capacity by reactor type; location of the plants; the plants in the world; and so forth. And, it also has some survey results on the 'Liberalization of electric power markets and nuclear power generation' such as some 70% of respondents in nuclear power for future option, gas-thermal power seen as power source with most to gain from liberalization, merits on nuclear power generation (environmental considerations and supply stability), most commonly voiced concern about new plant orders in poor economy, and so forth. (G.K.)

Development of a building sump database for the Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Sepanski, R.J.; Field, S.M.

1997-07-01

Operations at the Oak Ridge Y-12 Plant have resulted in contamination of Upper East Fork Poplar Creek (UEFPC) and shallow groundwater through soil erosion, infiltration, and outfall discharges. The contamination of groundwater has been documented for nearly two decades, largely through well monitoring efforts. This study represents the first effort to formally identify and compile location data on sumps at the Y-12 Plant, several of which are known or are suspected to pump groundwater. Operation of several of these sumps have been documented to affect groundwater hydraulics and contaminant pathways. This report presents preliminary results of an investigation attempting to identify sources of data on building sumps that have not previously been incorporated into existing Y-12 Plant groundwater databases. This investigation involved acquiring information on building sumps, such as location, building number, water source, discharge location, and availability of analytical data. This information was used to construct an ARC/INFO database capable of simultaneously storing spatial data on sump locations and attribute information concerning the operation of individual building sumps. This database will be referred to hereafter as the Y-12 Plant Building Sump Database

Bleomycin resistance : a new dominant selectable marker for plant cell transformation

NARCIS (Netherlands)

Hille, Jacques; Verheggen, Frank; Roelvink, Peter; Franssen, Henk; Kammen, Ab van; Zabel, Pim

1986-01-01

Plant cells are sensitive to the antibiotic bleomycin, a DNA damaging glycopeptide. A bleomycin resistance determinant, located on transposon Tn5 and functional in bacteria, has been cloned in a plant expression vector and introduced into Nicotiana plumbaginifolia using Agrobacterium tumefaciens.

Fungal-host diversity among mycoheterotrophic plants increases proportionally to their fungal-host overlap.

Science.gov (United States)

Gomes, Sofia I F; Merckx, Vincent S F T; Saavedra, Serguei

2017-05-01

The vast majority of plants obtain an important proportion of vital resources from soil through mycorrhizal fungi. Generally, this happens in exchange of photosynthetically fixed carbon, but occasionally the interaction is mycoheterotrophic, and plants obtain carbon from mycorrhizal fungi. This process results in an antagonistic interaction between mycoheterotrophic plants and their fungal hosts. Importantly, the fungal-host diversity available for plants is restricted as mycoheterotrophic interactions often involve narrow lineages of fungal hosts. Unfortunately, little is known whether fungal-host diversity may be additionally modulated by plant-plant interactions through shared hosts. Yet, this may have important implications for plant competition and coexistence. Here, we use DNA sequencing data to investigate the interaction patterns between mycoheterotrophic plants and arbuscular mycorrhizal fungi. We find no phylogenetic signal on the number of fungal hosts nor on the fungal hosts shared among mycoheterotrophic plants. However, we observe a potential trend toward increased phylogenetic diversity of fungal hosts among mycoheterotrophic plants with increasing overlap in their fungal hosts. While these patterns remain for groups of plants regardless of location, we do find higher levels of overlap and diversity among plants from the same location. These findings suggest that species coexistence cannot be fully understood without attention to the two sides of ecological interactions.

Cogeneration plant noise: Environmental impacts and abatement

International Nuclear Information System (INIS)

De Renzio, M.; Ciocca, B.

1991-01-01

In Italy, ever increasing attention to environmental problems has led to legislation requiring cogeneration plant owners to perform environmental impact assessments in order to determine plant conformity with pollution laws. This paper, based on an in-depth analysis of physics fundamentals relevant to the nature and effects of noise, examines the principal sources of noise in industrial cogeneration plants and the intensity and range of the effects of this noise on the local environment. A review is then made of the different methods of noise pollution abatement (e.g., heat and corrosion resistant silencers for gas turbines, varying types and thicknesses of acoustic insulation placed in specific locations) that can be effectively applied to cogeneration plant equipment and housing

Occurrence and fate of selected PPCPs in a conventional sewage treatment plant located in north west UK

International Nuclear Information System (INIS)

Reif, R.; Santos, A.; Judd, S. J.; Lema, J. M.; Omil, F.

2009-01-01

Over the last decade, the occurrence of pharmaceutical and personal care products (PPCPs) in wastewater effluents has become an increasing concern. Most of these compounds are released into the environment through sewage treatment plant effluents, due to the fact that these plants are not able to remove many of them in a significant extension. Presently, studies regarding hazardous effects in the aquatic environment are emerging worldwide, but still there is little information available regarding their potential eco toxicological effects. (Author)

Determination of trace elements in plant samples using XRF, PIXE and ICP-OES techniques

International Nuclear Information System (INIS)

Ahmed, Hassan Elzain Hassan

2014-07-01

The purpose of this study is to determine trace element concentration (Ca, Cu, Cr, K,Fe, Mn,Sr, and Za) in some sudanese wild plants namely, Ziziphus Abyssinica and Grewia Tenax. X-ray fluorescence ( X RF), particle-induced x-ray emission ( PIXE) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) techniques were used for element determination. A series of plants standard references materials were used to check the reliability of the different employed techniques as well as to estimate possible factors for correcting the concentration of some elements that deviated significantly from their actual concentration. The results showed that, X RF, PIXE and ICP-OES are equally competitive methods for measuring Ca,K, Fe, Sr and Zn elements. Unlikely to ICP-OES seems to be superior techniques tend to be appropriate methods for Cu determination in plant samples however, for Mn element PIXE and ICP-OES are advisable techniques for measuring this element rather than X RF method. On the other hand, ICP-OES seems to be the superior techniques over PIXE and X RF methods for Cr and Ni determination in plant samples. The effect of geographical location on trace elements concentration in plants has been examined through determination of element in different species of Grewia Tenax than collected from different location. Most of measured elements showed similarity indicating there is no significant impact of locations on the difference of element contents. In addition, two plants with different genetic families namely, Ziziphus Spina Christi and Ziziphus Abyssinica were collected from the same location and screened for their trace element content. It was found that there were no difference between the two plants for Ca, K, Cu, Fe, and Sr element. However, significant variations were observed for Mn and Zn concentrations implying the possibility of using of those two elements for plant taxonomy purposes.(Author)

Does rural space benefit from location of anaerobic digestion plants? Perspective of communal administration

Czech Academy of Sciences Publication Activity Database

Martinát, Stanislav; Mintálová, T.; Dvořák, Petr; Navrátil, J.; Klusáček, Petr; Kunc, J.

2013-01-01

Roč. 7, č. 2 (2013), s. 41-49 ISSN 1337-6748 R&D Projects: GA MŠk EE2.3.20.0025 Institutional support: RVO:68145535 Keywords : renewable sources of energy * public acceptance * a naerobic digestion plants * the Czech Republic Subject RIV: DE - Earth Magnetism, Geodesy, Geography http://geografia.science.upjs.sk/images/geographia_cassoviensis/articles/GC-2013-7-2/Martinat_akol_tlac3.pdf

Diverse urban plantings managed with sufficient resource availability can increase plant productivity and arthropod diversity

Directory of Open Access Journals (Sweden)

Jonathon eMuller

2014-10-01

Full Text Available Buildings structures and surfaces are explicitly being used to grow plants, and these ‘urban plantings’ are typically designed for aesthetic value. Urban plantings also have the potential to contribute significant ‘ecological values’ by increasing urban habitat for animals such as arthropods and by increasing plant productivity. In this study, we evaluated how the provision of these additional ecological values is affected by plant species richness; the availability of essential resources for plants, such as water, light, space; and soil characteristics. We sampled 33 plantings located on the exterior of three buildings in the urban centre of Brisbane, Australia (subtropical climatic region over two, six week sampling periods characterised by different temperature and rainfall conditions. Plant cover was estimated as a surrogate for productivity as destructive sampling of biomass was not possible. We measured weekly light levels (photosynthetically active radiation, plant CO2 assimilation, soil CO2 efflux, and arthropod diversity.Differences in plant cover were best explained by a three-way interaction of plant species richness, management water regime and sampling period. As the richness of plant species increased in a planter, productivity and total arthropod richness also increased significantly - likely due to greater habitat heterogeneity and quality. Overall we found urban plantings can provide additional ecological values if essential resources are maintained within a planter such as water, light and soil temperature. Diverse urban plantings that are managed with these principles in mind can contribute to the attraction of diverse arthropod communities, and lead to increased plant productivity within a dense urban context.

Lost in Location

DEFF Research Database (Denmark)

Hansen, Lone Koefoed

2009-01-01

traversed. While becoming destination aware, the individual loses her location awareness. The article proposes that the reason people get lost when using sat-nav is due to a wrong location-performative paradigm. As an alternative, the article introduces and analyzes two performance-related examples...... that illustrate an alternative location-performative paradigm: Meredith Warner's Lost/Found knitting series and Etter and Schecht's Melodious Walkabout. In both examples, the artist's hand becomes the intermediary between alien and location. Thus, by exploring how wayfinding can be a poetically situated...... performance, the article examines how the growing locative media industry can learn from the location-aware performative strategies employed by artists who create situated and urban performances for the curious participant. The academic frames employed in the analysis draw on psychogeography, site...

Vibration monitoring and fault diagnostics of a thermal power plant

International Nuclear Information System (INIS)

Hafeez, T.; Ghani, R.; Chohan, G.Y.; Amir, M.

2003-01-01

A thermal power plant was monitored from HP-turbine to the generator end. The vibration data at different plant locations was obtained with the help of a data collector/analyzer. The spectra of-all locations generate the symptoms for different problems of moderate and high vibration levels like bent shaft, misalignment in the exciter rotor and three couplings, mechanical looseness on generator and exciter sides. The possible causes of these faults are discussed on the basis of presented vibration spectra in this paper. The faults were later on rectified on the basis of this diagnostics. (author)

Protein (multi-)location prediction: using location inter-dependencies in a probabilistic framework

Science.gov (United States)

2014-01-01

Motivation Knowing the location of a protein within the cell is important for understanding its function, role in biological processes, and potential use as a drug target. Much progress has been made in developing computational methods that predict single locations for proteins. Most such methods are based on the over-simplifying assumption that proteins localize to a single location. However, it has been shown that proteins localize to multiple locations. While a few recent systems attempt to predict multiple locations of proteins, their performance leaves much room for improvement. Moreover, they typically treat locations as independent and do not attempt to utilize possible inter-dependencies among locations. Our hypothesis is that directly incorporating inter-dependencies among locations into both the classifier-learning and the prediction process can improve location prediction performance. Results We present a new method and a preliminary system we have developed that directly incorporates inter-dependencies among locations into the location-prediction process of multiply-localized proteins. Our method is based on a collection of Bayesian network classifiers, where each classifier is used to predict a single location. Learning the structure of each Bayesian network classifier takes into account inter-dependencies among locations, and the prediction process uses estimates involving multiple locations. We evaluate our system on a dataset of single- and multi-localized proteins (the most comprehensive protein multi-localization dataset currently available, derived from the DBMLoc dataset). Our results, obtained by incorporating inter-dependencies, are significantly higher than those obtained by classifiers that do not use inter-dependencies. The performance of our system on multi-localized proteins is comparable to a top performing system (YLoc+), without being restricted only to location-combinations present in the training set. PMID:24646119

Protein (multi-)location prediction: using location inter-dependencies in a probabilistic framework.

Science.gov (United States)

Simha, Ramanuja; Shatkay, Hagit

2014-03-19

Knowing the location of a protein within the cell is important for understanding its function, role in biological processes, and potential use as a drug target. Much progress has been made in developing computational methods that predict single locations for proteins. Most such methods are based on the over-simplifying assumption that proteins localize to a single location. However, it has been shown that proteins localize to multiple locations. While a few recent systems attempt to predict multiple locations of proteins, their performance leaves much room for improvement. Moreover, they typically treat locations as independent and do not attempt to utilize possible inter-dependencies among locations. Our hypothesis is that directly incorporating inter-dependencies among locations into both the classifier-learning and the prediction process can improve location prediction performance. We present a new method and a preliminary system we have developed that directly incorporates inter-dependencies among locations into the location-prediction process of multiply-localized proteins. Our method is based on a collection of Bayesian network classifiers, where each classifier is used to predict a single location. Learning the structure of each Bayesian network classifier takes into account inter-dependencies among locations, and the prediction process uses estimates involving multiple locations. We evaluate our system on a dataset of single- and multi-localized proteins (the most comprehensive protein multi-localization dataset currently available, derived from the DBMLoc dataset). Our results, obtained by incorporating inter-dependencies, are significantly higher than those obtained by classifiers that do not use inter-dependencies. The performance of our system on multi-localized proteins is comparable to a top performing system (YLoc+), without being restricted only to location-combinations present in the training set.

Lightning Attachment Estimation to Wind Turbines by Utilizing Lightning Location Systems

DEFF Research Database (Denmark)

Vogel, Stephan; Holbøll, Joachim; Lopez, Javier

2016-01-01

three different wind power plant locations are analyzed and the impact of varying data qualities is evaluated regarding the ability to detect upward lightning. This work provides a variety of background information which is relevant to the exposure assessment of wind turbine and includes practical......The goal of a lightning exposure assessment is to identify the number, type and characteristics of lightning discharges to a certain structure. There are various Lightning Location System (LLS) technologies available, each of them are characterized by individual performance characteristics....... In this work, these technologies are reviewed and evaluated in order to obtain an estimation of which technologies are eligible to perform a lightning assessment to wind turbines. The results indicate that ground-based mid-range low frequency (LF) LLS systems are most qualified since they combine a wide...

High-Throughput Analysis of T-DNA Location and Structure Using Sequence Capture.

Directory of Open Access Journals (Sweden)

Soichi Inagaki

Full Text Available Agrobacterium-mediated transformation of plants with T-DNA is used both to introduce transgenes and for mutagenesis. Conventional approaches used to identify the genomic location and the structure of the inserted T-DNA are laborious and high-throughput methods using next-generation sequencing are being developed to address these problems. Here, we present a cost-effective approach that uses sequence capture targeted to the T-DNA borders to select genomic DNA fragments containing T-DNA-genome junctions, followed by Illumina sequencing to determine the location and junction structure of T-DNA insertions. Multiple probes can be mixed so that transgenic lines transformed with different T-DNA types can be processed simultaneously, using a simple, index-based pooling approach. We also developed a simple bioinformatic tool to find sequence read pairs that span the junction between the genome and T-DNA or any foreign DNA. We analyzed 29 transgenic lines of Arabidopsis thaliana, each containing inserts from 4 different T-DNA vectors. We determined the location of T-DNA insertions in 22 lines, 4 of which carried multiple insertion sites. Additionally, our analysis uncovered a high frequency of unconventional and complex T-DNA insertions, highlighting the needs for high-throughput methods for T-DNA localization and structural characterization. Transgene insertion events have to be fully characterized prior to use as commercial products. Our method greatly facilitates the first step of this characterization of transgenic plants by providing an efficient screen for the selection of promising lines.

Little Botany: A Mobile Game Utilizing Data Integration to Enhance Plant Science Education

Directory of Open Access Journals (Sweden)

Suphanut Jamonnak

2017-01-01

Full Text Available Mobile devices are rapidly becoming the new medium of educational and social life for young people, and hence mobile educational games have become an important mechanism for learning. To help school-aged children learn about the fascinating world of plants, we present a mobile educational game called Little Botany, where players can create their own virtual gardens in any location on earth. One unique feature of Little Botany is that the game is built upon real-world data by leveraging data integration mechanism. The gardens created in Little Botany are augmented with real-world location data and real-time weather data. More specifically, Little Botany is using real-time weather data for the garden location to simulate how the weather affects plants growth. Little Botany players can learn to select what crops to plant, maintain their own garden, watch crops to grow, tend the crops on a daily basis, and harvest them. With this game, users can also learn plant structure and three chemical reactions.

Quarter Dates Location(s) Purpose Transportation and Travel ...

International Development Research Centre (IDRC) Digital Library (Canada)

IDRC CRDI

Dates. Location(s). Purpose. Transportation and Travel. Accommodation,. Meals and Other. Hospitality. Total. Expenses. Quarter 1. May 15. Ottawa, ON. Meetings. May 20 to 21. Washington DC. Conference. 11,364.93. 3,274.71. 53.50. 14,693.14. May 5 to June 5. Kenya and England. Meetings. June 18 to 21. Winnipeg, MB.

Invasive alien plants in protected areas within city borders, LODZ (poland)

International Nuclear Information System (INIS)

Anna, B.; Grzegorz, W.J.; Krason, K.

2017-01-01

The aim of the study was to present the occurrence of invasive alien plant species in two forest reserves: "Las Lagiewnicki"and "Polesie Konstantynowskie", located within the city of Lodz (Central Poland). Currently, five vascular plants (Impatiens parviflora, Juncus tenuis, Padus serotina, Quercus rubra, Robinia pseudoacacia) and one moss (Orthodontium lineare) considered as invasive were found in the studied reserves. Invasive plant species accounted for a small percentage of the flora in the studied reserves, and their sites were mainly concentrated in areas transformed by human activity. The most common species were Impatiens parviflora and Padus serotina. Due to the location of the reserves within city borders and the proven negative effect of the found species on ecological systems, their sites should be monitored. (author)

Models for the location decision for a combined cycle power plant : basic principles for solving the decision problem of the choice of location for a feasibility study of gas-fired power plants

OpenAIRE

Krüger, Jan

2015-01-01

The present thesis deals with the foundations for solving the decision problem of site selection for a feasibility study of gas-fired power plants, based on realistic and practical statements, under a business approach. The analysis of different theories and the investigation of site-relevant decision criteria has illustrated the broad range of site-specific factors and criteria that are to be taken into account. On the basis of existing projects, in which site theories were analysed for vari...

Atmospheric dispersion modeling of primary pollutants from electric power plants: Application to a coal-fired power plant

International Nuclear Information System (INIS)

McIlvaine, C.M.

1994-01-01

The normal operation of a power plant generally releases pollutants to the atmosphere. The objective of this paper is to describe a modeling method to estimate the changes in air pollutant concentrations that result from these emissions. This modeling approach is applicable to coal, biomass, oil, and natural gas technologies. As an example, this paper uses a hypothetical 500 megawatt (MW) coal-fired power plant, located at a Southeast Reference site in the U.S. and at a Southwest Reference Site. The pollutants resulting from the operation of the power plant may be classified as primary (emitted directly from the plant) or secondary (formed in the atmosphere from primary pollutants). The primary pollutants of interest in this paper are nitrogen oxides (NO x , sulfur dioxide SO 2 , particulate matter and metals

i-Locate - Indoor/Outdoor location and Asset Management through Open Data

Directory of Open Access Journals (Sweden)

Claudio Eccher

2015-02-01

Full Text Available Studi recenti hanno evidenziato che, in media, trascorriamo circa il 90% del nostro tempo in ambienti chiusi e, spesso, non familiari. L’esigenza di localizzare/guidare persone o ogg etti in spazi sia esterni che interni (senza discontinuità tra esterno ed interno darà origine ad una serie di nuovi servizi di tipo LBS (Location-Based Services che potranno avere anche una notevole rilevanza economica. i-locate (Indoor / outdoor location and Asset Management Through open geodata is a project that aims to develop a set of tools and services based on geo location technologies based on open data for the location and management of objects in indoor and outdoor spaces. The tools are intended both to citizens who use their smartphones to access services, aids to navigation from the front door to internal destinations to buildings (public office, clinic, shop, etc.. Obtaining any information available to support (code , unforeseen changes in the path, suggestions, etc., and professionals for specific activities that require the location of people, equipment, etc. i-locate to an intense use of GIS technologies for navigation and tracking "indoor" (indoor GIS, 3D GIS, to locate people (eg. Alzheimer's patients and their movements in areas not suited (geofencing to identify and track objects / portable equipment for their location, management and maintenance.

i-Locate - Indoor/Outdoor location and Asset Management through Open Data

Directory of Open Access Journals (Sweden)

Claudio Eccher

2015-02-01

Full Text Available Studi recenti hanno evidenziato che, in media, trascorriamo circa il 90% del nostro tempo in ambienti chiusi e, spesso, non familiari. L’esigenza di localizzare/guidare persone o ogg etti in spazi sia esterni che interni (senza discontinuità tra esterno ed interno darà origine ad una serie di nuovi servizi di tipo LBS (Location-Based Services che potranno avere anche una notevole rilevanza economica.i-locate (Indoor / outdoor location and Asset Management Through open geodata is a project that aims to develop a set of tools and services based on geo location technologies based on open data for the location and management of objects in indoor and outdoor spaces. The tools are intended both to citizens who use their smartphones to access services, aids to navigation from the front door to internal destinations to buildings (public office, clinic, shop, etc.. Obtaining any information available to support (code , unforeseen changes in the path, suggestions, etc., and professionals for specific activities that require the location of people, equipment, etc. i-locate to an intense use of GIS technologies for navigation and tracking "indoor" (indoor GIS, 3D GIS, to locate people (eg. Alzheimer's patients and their movements in areas not suited (geofencing to identify and track objects / portable equipment for their location, management and maintenance.

NIMBY, CLAMP, and the location of new nuclear-related facilities: U.S. national and 11 site-specific surveys.

Science.gov (United States)

Greenberg, Michael R

2009-09-01

Public and political opposition have made finding locations for new nuclear power plants, waste management, and nuclear research and development facilities a challenge for the U.S. government and the nuclear industry. U.S. government-owned properties that already have nuclear-related activities and commercial nuclear power generating stations are logical locations. Several studies and utility applications to the Nuclear Regulatory Commission suggest that concentrating locations at major plants (CLAMP) has become an implicit siting policy. We surveyed 2,101 people who lived within 50 miles of 11 existing major nuclear sites and 600 who lived elsewhere in the United States. Thirty-four percent favored CLAMP for new nuclear power plants, 52% for waste management facilities, and 50% for new nuclear laboratories. College educated, relatively affluent male whites were the strongest CLAMP supporters. They disproportionately trusted those responsible for the facilities and were not worried about existing nuclear facilities or other local environmental issues. Notably, they were concerned about continuing coal use. Not surprisingly, CLAMP proponents tended to be familiar with their existing local nuclear site. In short, likely CLAMP sites have a large and politically powerful core group to support a CLAMP policy. The challenge to proponents of nuclear technologies will be to sustain this support and expand the base among those who clearly are less connected and receptive to new nearby sites.

Location Systems An Introduction to the Technology Behind Location Awareness

CERN Document Server

LaMarca, Anthony

2008-01-01

Advances in electronic location technology and the coming of age of mobile computing have opened the door for location-aware applications to permeate all aspects of everyday life. Location is at the core of a large number of high-value applications ranging from the life-and-death context of emergency response to serendipitous social meet-ups. For example, the market for GPS products and services alone is expected to grow to US200 billion by 2015. Unfortunately, there is no single location technology that is good for every situation and exhibits high accuracy, low cost, and universal coverage.

Investigating the origin of Pb pollution in a terrestrial soil-plant-snail food chain by means of Pb isotope ratios

Energy Technology Data Exchange (ETDEWEB)

Notten, M.J.M. [Institute of Ecological Science, Department of System Ecology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam (Netherlands)], E-mail: m.notten@nunhems.com; Walraven, N. [Faculty of Geosciences, Department of Earth Sciences/Geochemistry, University of Utrecht, Budapestlaan 4, 3508 TA Utrecht (Netherlands); Beets, C.J. [Institute of Earth Sciences, Department of Quaternary Geology and Geomorphology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV Amsterdam (Netherlands); Vroon, P. [Institute of Earth Sciences, Department of Petrology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV Amsterdam (Netherlands); Rozema, J.; Aerts, R. [Institute of Ecological Science, Department of System Ecology, Vrije Universiteit Amsterdam, De Boelelaan 1085, 1081 HV, Amsterdam (Netherlands)

2008-06-15

Lead isotope ratios were used to trace the origin of Pb in a soil-plant (Urtica dioica)-snail (Cepaea nemoralis) food chain in two polluted locations in the floodplains of the rivers Meuse and Rhine (Biesbosch National Park) and one reference location in the Netherlands. Lead isotope ratios and concentrations were determined in soil, litter, plant leaves, snails, rainwater and airborne particulate matter. Anthropogenic Pb in the soils of all locations was found to be derived from deposition of Pb polluted river sediments. Discharging rivers influenced the reference location before being reclaimed from the sea. The river sediment contains anthropogenic Pb from various sources related to industrial activities in the hinterland of the rivers Meuse and Rhine. Lead in the atmosphere contributed substantially to Pb pollution and Pb transfer in plant leaves and snails in all locations. Lead pollution in plant leaves and snails can be explained from a mixture of river sediment-Pb and atmospheric Pb from various transfer routes that involve low concentrations.

Investigating the origin of Pb pollution in a terrestrial soil-plant-snail food chain by means of Pb isotope ratios

International Nuclear Information System (INIS)

Notten, M.J.M.; Walraven, N.; Beets, C.J.; Vroon, P.; Rozema, J.; Aerts, R.

2008-01-01

Lead isotope ratios were used to trace the origin of Pb in a soil-plant (Urtica dioica)-snail (Cepaea nemoralis) food chain in two polluted locations in the floodplains of the rivers Meuse and Rhine (Biesbosch National Park) and one reference location in the Netherlands. Lead isotope ratios and concentrations were determined in soil, litter, plant leaves, snails, rainwater and airborne particulate matter. Anthropogenic Pb in the soils of all locations was found to be derived from deposition of Pb polluted river sediments. Discharging rivers influenced the reference location before being reclaimed from the sea. The river sediment contains anthropogenic Pb from various sources related to industrial activities in the hinterland of the rivers Meuse and Rhine. Lead in the atmosphere contributed substantially to Pb pollution and Pb transfer in plant leaves and snails in all locations. Lead pollution in plant leaves and snails can be explained from a mixture of river sediment-Pb and atmospheric Pb from various transfer routes that involve low concentrations

Exergetic performance analysis of an ice-cream manufacturing plant: A comprehensive survey

International Nuclear Information System (INIS)

Dowlati, Majid; Aghbashlo, Mortaza; Mojarab Soufiyan, Mohamad

2017-01-01

In this study, a comprehensive exergetic performance analysis of an ice-cream manufacturing plant was conducted in order to pinpoint the locations of thermodynamic inefficiencies. Exergetic performance parameters of each subunit of the plant were determined and illustrated individually through writing and solving energy and exergy balance equations on the basis of real operational data. The required data were acquired from a local ice-cream factory located in Tehran, Iran. The plant included three main subsystems including water steam generator, refrigeration system, and ice-cream production line. An attempt was also made to quantify the specific exergy destruction of the ice-cream manufacturing process. The functional exergetic efficiency of the water steam generator, refrigeration system, and ice-cream production line was determined at 17.45%, 25.52%, and 5.71%, respectively. The overall functional exergetic efficiency of the process was found to be 2.15%, while the specific exergy destruction was calculated as 719.80 kJ/kg. In general, exergy analysis and its derivatives could provide invaluable information over the conventional energy analysis, suggesting potential locations for the plant performance improvement. - Highlights: • An ice-cream manufacturing plant was exergetically analyzed using the actual data. • Water steaming unit had the highest irreversibility rate among the plant subunits. • The specific exergy destruction of the ice-cream manufacturing was 719.80 kJ/kg. • The overall process exergetic efficiency of the process was found to be 2.15%.

Inventory of power plants in the United States: December 1979

International Nuclear Information System (INIS)

Gilliam, L.R.

1980-01-01

This 1979 inventory of power plants provides a comprehensive list of existing, standby, out-of-service, retired and projected electric generating plants in the U.S. Arranged under the broad sections of existing, jointly owned and projected units, tabulated data on individual plants in each state are presented. These data include unit name, location, type, MW rating, primary fuel, alternative fuel, status, year built, and whether or not it is jointly owned. Jointly owned plants are separately identified as to the percent of ownership belonging to named owners. Projected plants have data on plant characteristics, current status and scheduled completion date. Summaries of the total number of each type of power plant in each state are also provided

Nitrogen dose and plant density effects on popcorn grain yield ...

African Journals Online (AJOL)

and plant densities on grain yield and yield-related plant characteristics of popcorn in Hatay, located at Southern Mediterranean region of Turkey, during 2002 and 2003. The experiment was designed in a randomized complete block design with a split-plot arrangement with three replications. Nitrogen doses of 0, 120, 180 ...

Waste treatment plant

International Nuclear Information System (INIS)

Adesanmi, C.A

2009-01-01

Waste Treatment Plant (WTP) is designed to provide appropriate systems for processing, immobilization and storage of low and medium radioactive waste arising from the operation of the research facilities of the Nuclear Technology Centre (NTC). It will serve as central collection station processing active waste generated through application of radionuclide in science, medicine and industry in the country. WTP building and structures will house the main waste processing systems and supporting facilities. All facilities will be interconnected. The interim storage building for processed waste drums will be located separately nearby. The separate interim storage building is located near the waste treatment building. Considering the low radiation level of the waste, storage building is large with no solid partitioning walls and with no services or extra facilities other than lighting and smoke alarm sensors. The building will be designed such that drums(200-1)are stacked 3 units high using handling by fork lift truck. To prevent radiation exposure to on-site personnel, the interim storage building will be erected apart from waste treatment plant or other buildings. The interim storage building will also be ready for buffer storage of unconditioned waste waiting for processing or decay and for storage material from the WTP

Quiet planting in the locked constraints satisfaction problems

Energy Technology Data Exchange (ETDEWEB)

Zdeborova, Lenka [Los Alamos National Laboratory; Krzakala, Florent [Los Alamos National Laboratory

2009-01-01

We study the planted ensemble of locked constraint satisfaction problems. We describe the connection between the random and planted ensembles. The use of the cavity method is combined with arguments from reconstruction on trees and first and second moment considerations; in particular the connection with the reconstruction on trees appears to be crucial. Our main result is the location of the hard region in the planted ensemble, thus providing hard satisfiable benchmarks. In a part of that hard region instances have with high probability a single satisfying assignment.

Monitoring Biological Activity at Geothermal Power Plants

Energy Technology Data Exchange (ETDEWEB)

Peter Pryfogle

2005-09-01

The economic impact of microbial growth in geothermal power plants has been estimated to be as high as $500,000 annually for a 100 MWe plant. Many methods are available to monitor biological activity at these facilities; however, very few plants have any on-line monitoring program in place. Metal coupon, selective culturing (MPN), total organic carbon (TOC), adenosine triphosphate (ATP), respirometry, phospholipid fatty acid (PLFA), and denaturing gradient gel electrophoresis (DGGE) characterizations have been conducted using water samples collected from geothermal plants located in California and Utah. In addition, the on-line performance of a commercial electrochemical monitor, the BIoGEORGE?, has been evaluated during extended deployments at geothermal facilities. This report provides a review of these techniques, presents data on their application from laboratory and field studies, and discusses their value in characterizing and monitoring biological activities at geothermal power plants.

Seismic environment of Deccan Volcanic Province (DVP) and its suitability for location of new nuclear power plants in India - a few geoscientific opinions

International Nuclear Information System (INIS)

Sinha, D.K.; Parihar, P.S.

2014-01-01

India has an ambitious programme to expand the nuclear power capacity to 60 GWe by 2032 and 655 GWe by 2050. Such an exponential growth of nuclear power generation warranty identification of suitable sites for nuclear power reactors. Perhaps the 6000 km long vast coastline is the best choice for siting new NPPs because of ready availability of sea water and a quiet seismic environment. Large inland areas with adequate water resources provide additional locations to cater the power requirements of Central and Northern India. In this perspective, the potentials of Deccan Volcanic Province (DVP) for siting new NPPs is discussed. Five zones delineated as safer sites of nuclear power plants on Deccan Trap, are the first hand targets identified by this study. Two of them are situated to the north of Narmada-Son Lineament and have large areas. Chambal and Betwa river systems of Ganga Basin are perennial source of water along with several dams constructed on their course. The other three zones are located to the south of Narmada-Son Lineament and are small in size. The Konkan Coastal Lineament (N-S) in the west and Kurduwadi Lineament (NW-SE) in the east are major tectonic features bordering these zones. The Godavari and Krishna rivers are perennial water sources. Presence of reservoirs within the delineated zones stands advantageous considering their potential as ultimate heat sinks. All the five zones are devoid of any known major seismicity. Thick basalt cover provides good foundation conditions and engineerability for these zones. Considering above characteristics, proposed five zones could be good candidate sites for future NPPs, after their detailed geotechnical investigations. (author)

Fire scenarios in nuclear power plant

International Nuclear Information System (INIS)

Asp, I.B.; MacDougall, E.A.; Hall, R.E.

1978-01-01

This report defines a Design Base Fire and looks at 3 major areas of a hypothetical model for a Nuclear Power Plant. In each of these areas a Design Base Fire was developed and explained. In addition, guidance is given for comparing fire conditions of a given Nuclear Power Plant with the model plant described. Since there is such a wide variation in nuclear plant layouts, model areas were chosen for simplicity. The areas were not patterned after any existing plant area; rather several plant layouts were reviewed and a simplified model developed. The developed models considered several types of fires. The fire selected was considered to be the dominant one for the case in point. In general, the dominant fire selected is time dependent and starts at a specific location. After these models were developed, a comparison was drawn between the model and an operating plant for items such as area, cable numbers and weight, tray sizes and lengths. The heat loads of the model plant are summarized by area and compared with those of an actual operating plant. This document is intended to be used as a guide in the evaluation of fire hazards in nuclear power stations and a summarization of one acceptable analytical methodology to accomplish this

A heuristic algorithm for a multi-product four-layer capacitated location-routing problem

Directory of Open Access Journals (Sweden)

Mohsen Hamidi

2014-01-01

Full Text Available The purpose of this study is to solve a complex multi-product four-layer capacitated location-routing problem (LRP in which two specific constraints are taken into account: 1 plants have limited production capacity, and 2 central depots have limited capacity for storing and transshipping products. The LRP represents a multi-product four-layer distribution network that consists of plants, central depots, regional depots, and customers. A heuristic algorithm is developed to solve the four-layer LRP. The heuristic uses GRASP (Greedy Randomized Adaptive Search Procedure and two probabilistic tabu search strategies of intensification and diversification to tackle the problem. Results show that the heuristic solves the problem effectively.

Harmattan gas plant compressor conversion

Energy Technology Data Exchange (ETDEWEB)

Temple, K. [Altagas Ltd., Calgary, AB (Canada)

2009-07-01

The Harmattan Gas Plant located near the town of Didsbury, Alberta has typical processing units such as amine treating, sulfur recovery, refrigeration, and dehydration. In 1999, a deep cut turbo expander train was added for the extraction of ethane and in 2003 a spec carbon dioxide unit was added. Since its construction in 1961, the plant has undergone many modifications. As such, the plant is a mix of new and old equipment. A 3500 kW Solar Centaur 50LS gas turbine compressor with waste heat recovery was installed at the plant in 2008. This paper reviewed the project from concept to execution and demonstrated how reciprocating compressors were economically replaced with a gas turbine. Altagas had an incentive to invest in the project to lower operating and maintenance costs. Altagas was able to economically replace aging reciprocating compressors with a single turbine driving a centrifugal compressor without any producer subsidies or contract revisions. 2 tabs., 5 figs.

Estimating suitable environments for invasive plant species across large landscapes: a remote sensing strategy using Landsat 7 ETM+

Science.gov (United States)

Young, Kendal E.; Abbott, Laurie B.; Caldwell, Colleen A.; Schrader, T. Scott

2013-01-01

The key to reducing ecological and economic damage caused by invasive plant species is to locate and eradicate new invasions before they threaten native biodiversity and ecological processes. We used Landsat Enhanced Thematic Mapper Plus imagery to estimate suitable environments for four invasive plants in Big Bend National Park, southwest Texas, using a presence-only modeling approach. Giant reed (Arundo donax), Lehmann lovegrass (Eragrostis lehmanniana), horehound (Marrubium vulgare) and buffelgrass (Pennisteum ciliare) were selected for remote sensing spatial analyses. Multiple dates/seasons of imagery were used to account for habitat conditions within the study area and to capture phenological differences among targeted species and the surrounding landscape. Individual species models had high (0.91 to 0.99) discriminative ability to differentiate invasive plant suitable environments from random background locations. Average test area under the receiver operating characteristic curve (AUC) ranged from 0.91 to 0.99, indicating that plant predictive models exhibited high discriminative ability to differentiate suitable environments for invasive plant species from random locations. Omission rates ranged from <1.0 to 18%. We demonstrated that useful models estimating suitable environments for invasive plants may be created with <50 occurrence locations and that reliable modeling using presence-only datasets can be powerful tools for land managers.

Developments in power plant cooling systems

International Nuclear Information System (INIS)

Agarwal, N.K.

1993-01-01

A number of cooling systems are used in the power plants. The condenser cooling water system is one of the most important cooling systems in the plant. The system comprises a number of equipment. Plants using sea water for cooling are designed for the very high corrosion effects due to sea water. Developments are taking place in the design, materials of construction as well as protection philosophies for the various equipment. Power optimisation of the cycle needs to be done in order to design an economical system. Environmental (Protection) Act places certain limitations on the effluents from the plant. An attempt has been made in this paper to outline the developing trends in the various equipment in the condenser cooling water systems used at the inland as well as coastal locations. (author). 5 refs., 6 refs

Transfer of 40K, 238U, 210Pb, and 210Po from soil to plant in various locations in south of Syria

International Nuclear Information System (INIS)

Al-Masri, M.S.; Al-Akel, B.; Nashawani, A.; Amin, Y.; Khalifa, K.H.; Al-Ain, F.

2008-01-01

Transfer factors of 40 K, 238 U, 210 Pb, and 210 Po from soil to some agriculture crops in various locations in south of Syria (Dara'a and Assuwaydaa districts) have been determined. Soil and vegetable crops (green pepper, cucumber, tomato, and eggplant), legumes crops (lentil, chickpea, and broad bean), fruit trees (apple, grape, and olives) and cereals (barley and wheat) were collected and analyzed for 238 U, 210 Pb, and 210 Po. The results have shown that higher transfer factors (calculated as Bq kg -1 dry wt. plant material per Bq kg -1 dry wt. soil) for 210 Po, 210 Pb and 238 U were observed in vegetable leaves than fruits and cereals leaves; the highest values of transfer factor (TF) for 238 U were found to be 0.1 for straw of chickpea. Transfer factors for 210 Po varied between 2.8 x 10 -2 and 2 in fruits of eggplant and grain of barley, respectively. In addition, several parameters affecting transfer factors of the radionuclides were evaluated. The results can be considered as base values for TF of natural radionuclides in the region

Alien plant invasions in European woodlands

NARCIS (Netherlands)

Wagner, Viktoria; Chytrý, Milan; Jiménez-Alfaro, Borja; Pergl, Jan; Hennekens, Stephan; Biurrun, Idoia; Knollová, Ilona; Berg, Christian; Vassilev, Kiril; Rodwell, John S.; Škvorc, Željko; Jandt, Ute; Ewald, Jörg; Jansen, Florian; Tsiripidis, Ioannis; Botta-Dukát, Zoltán; Casella, Laura; Attorre, Fabio; Rašomavičius, Valerijus; Ćušterevska, Renata; Schaminée, Joop H.J.; Brunet, Jörg; Lenoir, Jonathan; Svenning, Jens Christian; Kącki, Zygmunt; Petrášová-Šibíková, Mária; Šilc, Urban; García-Mijangos, Itziar; Campos, Juan Antonio; Fernández-González, Federico; Wohlgemuth, Thomas; Onyshchenko, Viktor; Pyšek, Petr

2017-01-01

Aim: Woodlands make up a third of European territory and carry out important ecosystem functions, yet a comprehensive overview of their invasion by alien plants has never been undertaken across this continent. Location: Europe. Methods: We extracted data from 251,740 vegetation plots stored in the

Model plant Key Measurement Points

International Nuclear Information System (INIS)

Schneider, R.A.

1984-01-01

For IAEA safeguards a Key Measurement Point is defined as the location where nuclear material appears in such a form that it may be measured to determine material flow or inventory. This presentation describes in an introductory manner the key measurement points and associated measurements for the model plant used in this training course

Thermo-economic design optimization of parabolic trough solar plants for industrial process heat applications with memetic algorithms

International Nuclear Information System (INIS)

Silva, R.; Berenguel, M.; Pérez, M.; Fernández-Garcia, A.

2014-01-01

Highlights: • A thermo-economic optimization of a parabolic-trough solar plant for industrial process heat applications is developed. • An analysis of the influence of economic cost functions on optimal design point location is presented. • A multi-objective optimization approach to the design routine is proposed. • A sensitivity analysis of the optimal point location to economic, operational, and ambient conditions is developed. • Design optimization of a parabolic trough plant for a reference industrial application is developed. - Abstract: A thermo-economic design optimization of a parabolic trough solar plant for industrial processes with memetic algorithms is developed. The design domain variables considered in the optimization routine are the number of collectors in series, number of collector rows, row spacing, and storage volume. Life cycle savings, levelized cost of energy, and payback time objective functions are compared to study the influence on optimal design point location. Furthermore a multi-objective optimization approach is proposed to analyze the design problem from a multi-economic criteria point of view. An extensive set of optimization cases are performed to estimate the influence of fuel price trend, plant location, demand profile, operation conditions, solar field orientation, and radiation uncertainty on optimal design. The results allow quantifying as thermo-economic design optimization based on short term criteria as the payback time leads to smaller plants with higher solar field efficiencies and smaller solar fractions, while the consideration of optimization criteria based on long term performance of the plants, as life cycle savings based optimization, leads to the reverse conclusion. The role of plant location and future evolution of gas prices in the thermo-economic performance of the solar plant has been also analyzed. Thermo-economic optimization of a parabolic trough solar plant design for the reference industrial

Exergy analysis of a MSF distillation plant

International Nuclear Information System (INIS)

Kahraman, Nafiz; Cengel, Yunus A.

2005-01-01

In this paper, a large MSF distillation plant in the gulf area is analyzed thermodynamically using actual plant operation data. Exergy flow rates are evaluated throughout the plant, and the exergy flow diagram is prepared. The rates of exergy destruction and their percentages are indicated on the diagram so that the locations of highest exergy destruction can easily be identified. The highest exergy destruction (77.7%) occurs within the MSF unit, as expected, and this can be reduced by increasing the number of flashing stages. The exergy destruction in the pumps and motors account for 5.3% of the total, and this also can be reduced by using high efficiency motors and pumps. The plant is determined to have a second law efficiency of just 4.2%, which is very low. This indicates that there are major opportunities in the plant to reduce exergy destruction and, thus, the amount of electric and thermal energy supplied, making the operation of the plant more cost effective

Preliminary design of the Carrisa Plains solar central receiver power plant. Volume I. Executive summary

Energy Technology Data Exchange (ETDEWEB)

1983-12-31

The design of the 30 MWe central receiver solar power plant to be located at Carrisa Plains, San Luis Obispo County, California, is summarized. The plant uses a vertical flat-panel (billboard) solar receiver located at the top of a tower to collect solar energy redirected by approximately 1900 heliostats located to the north of the tower. The solar energy is used to heat liquid sodium pumped from ground level from 610 to 1050/sup 0/F. The power conversion system is a non-reheat system, cost-effective at this size level, and designed for high-efficiency performance in an application requiring daily startup. Successful completion of this project will lead to power generation starting in 1986. This report also discusses plant performance, operations and maintenance, development, and facility cost estimate and economic analysis.

LocateP: Genome-scale subcellular-location predictor for bacterial proteins

Directory of Open Access Journals (Sweden)

Zhou Miaomiao

2008-03-01

Full Text Available Abstract Background In the past decades, various protein subcellular-location (SCL predictors have been developed. Most of these predictors, like TMHMM 2.0, SignalP 3.0, PrediSi and Phobius, aim at the identification of one or a few SCLs, whereas others such as CELLO and Psortb.v.2.0 aim at a broader classification. Although these tools and pipelines can achieve a high precision in the accurate prediction of signal peptides and transmembrane helices, they have a much lower accuracy when other sequence characteristics are concerned. For instance, it proved notoriously difficult to identify the fate of proteins carrying a putative type I signal peptidase (SPIase cleavage site, as many of those proteins are retained in the cell membrane as N-terminally anchored membrane proteins. Moreover, most of the SCL classifiers are based on the classification of the Swiss-Prot database and consequently inherited the inconsistency of that SCL classification. As accurate and detailed SCL prediction on a genome scale is highly desired by experimental researchers, we decided to construct a new SCL prediction pipeline: LocateP. Results LocateP combines many of the existing high-precision SCL identifiers with our own newly developed identifiers for specific SCLs. The LocateP pipeline was designed such that it mimics protein targeting and secretion processes. It distinguishes 7 different SCLs within Gram-positive bacteria: intracellular, multi-transmembrane, N-terminally membrane anchored, C-terminally membrane anchored, lipid-anchored, LPxTG-type cell-wall anchored, and secreted/released proteins. Moreover, it distinguishes pathways for Sec- or Tat-dependent secretion and alternative secretion of bacteriocin-like proteins. The pipeline was tested on data sets extracted from literature, including experimental proteomics studies. The tests showed that LocateP performs as well as, or even slightly better than other SCL predictors for some locations and outperforms

Diversity of Endophytic Fungi from Red Ginger (Zingiber officinale Rosc. Plant and Their Inhibitory Effect to Fusarium oxysporum Plant Pathogenic Fungi

Directory of Open Access Journals (Sweden)

ROHANI CINTA BADIA GINTING

2013-09-01

Full Text Available Indonesia has been known as a country with high medicinal plant diversity. One of the most common medicinal plant from Indonesia is red ginger (Zingiber officinale Rosc.. Nevertheless, limited studies of endophytic fungi associated with these medicinal plants are hitherto available. The objectives of this research were to study the diversity of endophytic fungi on red ginger and to analyze their potential as a source of antifungal agent. All parts of plant organs such as leaf, rhizome, root, and stem were subjected for isolation. Fungal identification was carried out by using a combination of morphological characteristic and molecular analysis of DNA sequence generated from ITS rDNA region. Thirty endophytic fungi were successfully isolated from leaf, rhizome, root, and stem of red ginger plant. Antagonistic activity was tested against Fusarium oxysporum, a pathogenic fungus on plants, using an antagonistic assay. Based on this approach, the fungi were assigned as Acremonium macroclavatum, Beltraniella sp., Cochliobolus geniculatus and its anamorphic stage Curvularia affinis, Fusarium solani, Glomerella cingulata and its anamorphic stage Colletotrichum gloeosporoides, Lecanicillium kalimantanense, Myrothecium verrucaria, Neonectria punicea, Periconia macrospinosa, Rhizopycnis vagum, and Talaromyces assiutensis. R. vagum was found specifically on root whereas C. affinis, L. kalimantanense, and M. verrucaria were found on stem of red ginger plant. A. macroclavatum was found specifically in red ginger plant's organ which located under the ground, whereas C. affinis was found from shoot or organ which located above the ground. The antagonistic activity of isolated endophytic fungi against F. oxysporum varied with the inhibition value range from 1.4 to 68.8%. C. affinis (JMbt7, F. solani (JMd14, and G. cingulata (JMr2 had significantly high antagonistic activity with the value above 65%; and R. vagum (JMa4 and C. geniculatus (JMbt9 had significantly

Profitability and sustainability of small - medium scale palm biodiesel plant

Science.gov (United States)

Solikhah, Maharani Dewi; Kismanto, Agus; Raksodewanto, Agus; Peryoga, Yoga

2017-06-01

The mandatory of biodiesel application at 20% blending (B20) has been started since January 2016. It creates huge market for biodiesel industry. To build large-scale biodiesel plant (> 100,000 tons/year) is most favorable for biodiesel producers since it can give lower production cost. This cost becomes a challenge for small - medium scale biodiesel plants. However, current biodiesel plants in Indonesia are located mainly in Java and Sumatra, which then distribute biodiesel around Indonesia so that there is an additional cost for transportation from area to area. This factor becomes an opportunity for the small - medium scale biodiesel plants to compete with the large one. This paper discusses the profitability of small - medium scale biodiesel plants conducted on a capacity of 50 tons/day using CPO and its derivatives. The study was conducted by performing economic analysis between scenarios of biodiesel plant that using raw material of stearin, PFAD, and multi feedstock. Comparison on the feasibility of scenarios was also conducted on the effect of transportation cost and selling price. The economic assessment shows that profitability is highly affected by raw material price so that it is important to secure the source of raw materials and consider a multi-feedstock type for small - medium scale biodiesel plants to become a sustainable plant. It was concluded that the small - medium scale biodiesel plants will be profitable and sustainable if they are connected to palm oil mill, have a captive market, and are located minimally 200 km from other biodiesel plants. The use of multi feedstock could increase IRR from 18.68 % to 56.52 %.

Environmental impact assessment of pharmaceutical prescriptions: Does location matter?

Science.gov (United States)

Oldenkamp, Rik; Huijbregts, Mark A J; Hollander, Anne; Ragas, Ad M J

2014-11-01

A methodology was developed for the assessment and comparison of the environmental impact of two alternative pharmaceutical prescriptions. This methodology provides physicians with the opportunity to include environmental considerations in their choice of prescription. A case study with the two antibiotics ciprofloxacin and levofloxacin at three locations throughout Europe showed that the preference for a pharmaceutical might show spatial variation, i.e. comparison of two pharmaceuticals might yield different results when prescribed at different locations. This holds when the comparison is based on both the impact on the aquatic environment and the impact on human health. The relative impacts of ciprofloxacin and levofloxacin on human health were largely determined by the local handling of secondary sludge, agricultural disposal practices, the extent of secondary sewage treatment, and local food consumption patterns. The relative impacts of ciprofloxacin and levofloxacin on the aquatic environment were mostly explained by the presence of specific sewage treatment techniques, as effluents from sewage treatment plants (STPs) are the most relevant emission pathway for the aquatic environment. Copyright © 2014 Elsevier Ltd. All rights reserved.

Optimization, selection and feasibility study of solar parabolic trough power plants for Algerian conditions

International Nuclear Information System (INIS)

Boukelia, T.E.; Mecibah, M.S.; Kumar, B.N.; Reddy, K.S.

2015-01-01

Highlights: • Evaluation of solar resources in the absence of measured data. • Optimization of 2 PTSTPPs integrated with TES and FBS and using oil and salt as HTFs. • 4E comparative study of the two optimized plants alongside the Andasol 1 plant. • The salt plant resulting as the best one and has been chosen for the viability study. • Tamanrasset is the best location for construction of PTSTPPs. - Abstract: In the present study, optimization of two parabolic trough solar thermal power plants integrated with thermal energy storage (TES), and fuel backup system (FBS) has been performed. The first plant uses Therminol VP-1 as heat transfer fluid in the solar field and the second plant uses molten salt. The optimization is carried out with solar multiple (SM) and full load hours of TES as the parameters, with an objective of minimizing the levelized cost of electricity (LCOE) and maximizing the annual energy yield. A 4E (energy–exergy–environment–economic) comparison of the optimized plants alongside the Andasol 1 as reference plant is studied. The molten salt plant resulting as the best technology, from the optimization and 4E comparative study has been chosen for the viability analysis of ten locations in Algeria with semi-arid and arid climatic conditions. The results indicate that Andasol 1 reference plant has the highest mean annual energy efficiency (17.25%) and exergy efficiency (23.30%). Whereas, the highest capacity factor (54.60%) and power generation (236.90 GW h) are exhibited by the molten salt plant. The molten salt plant has least annual water usage of about 800,482 m 3 , but demands more land for the operation. Nevertheless the oil plant emits the lowest amount of CO 2 gas (less than 40.3 kilo tonnes). From the economic viewpoint, molten salt seems to be the best technology compared to other plants due to its lowest investment cost (less than 360 million dollars) and lower levelized cost of electricity (LCOE) (8.48 ¢/kW h). The

Radionuclides in biota collected near a dicalcium phosphate plant, southern Catalonia, Spain

International Nuclear Information System (INIS)

Mola, M.; Palomo, M.; Penalver, A.; Aguilar, C.; Borrull, F.

2013-01-01

Industrial waste containing radioactive U-decay series isotopes was released into the Ebro River, Spain, over a period of >20 years from a dicalcium phosphate (DCP) plant. This release raised activities of several natural radionuclides (e.g. 238 U, 234 U, 230 Th, 232 Th and 226 Ra) in biota taken from the area near the DCP plant. Plants and animals selected for this study included the green algae (Cladophora glomerata), the blue mussel (Mytilus edulis), the zebra mussel (Dreissena polymorpha) and the scavenger catfish (Silurus glanis) because they are all common in the area. Multiple sampling points were chosen for this study: (1) a site in the Riba-Roja Reservoir, above the DCP plant's area of influence, (2) four sites in the area surrounding the DCP plant, close to the town of Flix, and (3) a location in the Ebro Delta Estuary in Fangar Bay. Significant differences in the activities (in Bq kg -1 of dry weight) for the radioisotopes included in this study among samples were attributed to sample location and the species evaluated. For instance, relatively high activities for uranium and radium were obtained in algae collected around the DCP plant, compared to results obtained for algae samples taken from the unimpacted Riba-Roja Reservoir. In contrast, for zebra mussels, enhanced activities were observed for all radionuclides and, in particular, for thorium and radium isotopes within the area of influence. Among catfish samples, activity values from different locations were not significantly different, though slightly higher activities were observed at the sampling point just downstream of the DCP factory. (author)

Directory of nuclear power plants in the world, 1985

International Nuclear Information System (INIS)

Fujii, Haruo

1985-01-01

This book presents technical information and estimates trends of load factors and construction costs of nuclear power plants. Particularly road maps indicating plants are drawn in, which would be practical in visiting them. The data used here are directly confirmed by operators in every part of the world. Therefore, they reflect up-to-date nuclear power developments and its future. This allows wide and exact understanding of world's nuclear power. Chapter 1 presents nuclear power growth around the world and estimates forecasts based on information from electric power companies: nuclear power growths and the growths in the number of reactors around the world, in WOCA (World outside the Centrally Planned Economies Area), in CPEA (Centrally Planned Economies Area) are analyzed in detail. Chapter 2 presents nuclear power plants on maps by country. The maps show exact locations of nuclear power plants with local cities around them, rivers and lakes. For convenience, symbols are given to aid in identifying the types of reactors. Chapter 3 presents general information of nuclear power plants. Also the addresses of operators, all segments of nuclear power supply industries and nuclear organizations are included. For convenience, the index of nuclear power plants is added. Chapter 4 presents technical information, road maps in large scales and photographs of nuclear power plants in the world. The road maps show exact locations of plants. Chapter 5 presents operating experiences, load factors, refuelling and maintenance outages. The trends of data are analyzed both regionally (WOCA, CPEA) and world-widely. Chapter 6 presents trends of construction costs, component costs as percent of total construction costs and direct costs, and construction durations. (J.P.N.)

Tritium accounting for PHWR plants

International Nuclear Information System (INIS)

Nair, P.S.; Duraisamy, S.

2012-01-01

Tritium, the radioactive isotope of hydrogen, is produced as a byproduct of the nuclear reactions in the nuclear power plants. In a Pressurized Heavy Water Reactor (PHWR) tritium activity is produced in the Heat Transport and Moderator systems due to neutron activation of deuterium in heavy water used in these systems. Tritium activity build up occurs in some of the water systems in the PHWR plants through pick up from the plant atmosphere, inadvertent D 2 O ingress from other systems or transfer during processes. The tritium, produced by the neutron induced reactions in different systems in the reactor undergoes multiple processes such as escape through leaks, storage, transfer to external locations, decay, evaporation and diffusion and discharge though waste streams. Change of location of tritium inventory takes place during intentional transfer of heavy water, both reactor grade and downgraded, from one system to another. Tritium accounting is the application of accounting techniques to maintain knowledge of the tritium inventory present in different systems of a facility and to construct activity balances to detect any discrepancy in the physical inventories. It involves identification of all the tritium hold ups, transfers and storages as well as measurement of tritium inventories in various compartments, decay corrections, environmental release estimations and evaluation of activity generation during the accounting period. This paper describes a methodology for creating tritium inventory balance based on periodic physical inventory taking, tritium build up, decay and release estimations. Tritium accounting in the PHWR plants can prove to be an effective regulatory tool to monitor its loss as well as unaccounted release to the environment. (author)

Cost analysis of light water reactor power plants

International Nuclear Information System (INIS)

Mooz, W.E.

1978-06-01

A statistical analysis is presented of the capital costs of light water reactor (LWR) electrical power plants. The objective is twofold: to determine what factors are statistically related to capital costs and to produce a methodology for estimating these costs. The analysis in the study is based on the time and cost data that are available on U.S. nuclear power plants. Out of a total of about 60 operating plants, useful capital-cost data were available on only 39 plants. In addition, construction-time data were available on about 65 plants, and data on completed construction permit applications were available for about 132 plants. The cost data were first systematically adjusted to constant dollars. Then multivariate regression analyses were performed by using independent variables consisting of various physical and locational characteristics of the plants. The dependent variables analyzed were the time required to obtain a construction permit, the construction time, and the capital cost

Thermal performance analysis of a solar heating plant

DEFF Research Database (Denmark)

Fan, Jianhua; Huang, Junpeng; Andersen, Ola Lie

was developed to calculate thermal performances of the plant. In the Trnsys model, three solar collector fields with a total solar collector area of 33,300 m2, a seasonal water pit heat storage of 75,000 m3, a simplified CO2 HP, a simplified ORC unit and a simplified wood chip boiler were included. The energy......Detailed measurements were carried out on a large scale solar heating plant located in southern Denmark in order to evaluate thermal performances of the plant. Based on the measurements, energy flows of the plant were evaluated. A modified Trnsys model of the Marstal solar heating plant...... consumption of the district heating net was modeled by volume flow rate and given forward and return temperatures of the district heating net. Weather data from a weather station at the site of the plant were used in the calculations. The Trnsys calculated yearly thermal performance of the solar heating plant...

Design of a nuclear steam reforming plant

International Nuclear Information System (INIS)

Malherbe, J.

1980-01-01

The design of a plant for the steam reforming of methane using a High Temperature Reactor has been studied by CEA in connection with the G.E.G.N. This group of companies (CEA, GAZ DE FRANCE, CHARBONNAGES DE FRANCE, CREUSOT-LOIRE, NOVATOME) is in charge of studying the feasibility of the coal gasification process by using a nuclear reactor. The process is based on the hydrogenation of the coal in liquid phase with hydrogen produced by a methane steam reformer. The reformer plant is fed by a pipe of natural gas or SNG. The produced hydrogen feeds the gasification plant which could not be located on the same site. An intermediate hydrogen storage between the two plants could make the coupling more flexible. The gasification plant does not need a great deal of heat and this heat can be satisfied mostly by internal heat exchanges

Evaluating the impacts of power plant emissions in Mexico

Energy Technology Data Exchange (ETDEWEB)

Lopez Villegas, M.T.; Tzintzun Cervantes, M.G.; Iniestra Gomez, R.; Garibay Bravo, V.; Zuk, M.; Rojas Bracho, L.; Fernandez Bremautz, A. [Direccion de Investigacion sobre Calidad del Aire, Inst. Nacional de Ecologia (Mexico)

2004-07-01

Mexican electricity generation has proven to be a large source of air pollution nationwide. According to the Energy Secretariat, electricity generation in Mexico accounts for 68% of SO{sub 2} emissions, 24% of PM{sub 10} emissions and 20% of NO{sub x} emissions nationwide. The country's total effective installed capacity is 42,067 MW, of which 67% corresponds to thermoelectric power plants. Heavy fuel oil, known as 'combustoleo', is used in many thermoelectric plants primarily for regular operation. The typical sulphur content of 'combustoleo' is approximately 2.5 to 4%. As a first step to determine the potential impacts of Mexican power plants on regional air pollution and health, we conducted a case study on the Adolfo Lopez Mateos power plant, located in the town of Tuxpan in the eastern state of Veracruz. The plant is located on the northern coast of the Gulf of Mexico; therefore greatly influenced by the weather of the region. We used the CALPUFF Lagrangian puff model (Earth Tech, Concord, MA) to simulate the dispersion of SO{sub 2}, NO{sub x} and primary PM{sub 10} emissions from the power plant stacks and the formation of secondary particulate matter. We considered a 120km x 120km grid, with a resolution of 2km x 2km and height of 2500 km. This area comprises approximately 791,000 inhabitants, including rural and urban populations. (orig.)

Annual radiological environmental operating report: Sequoyah Nuclear Plant, 1987

International Nuclear Information System (INIS)

1988-04-01

This report describes the environmental radiological monitoring program conducted by TVA in the vicinity of the Sequoyah Nuclear Plant in 1987. The program includes the collection of samples from the environment and the determination of the concentrations of radioactive materials in the samples. Samples are taken from stations in the general area of the plant and from areas not influenced by plant operations. Station locations are selected after careful consideration of the weather patterns and projected radiation doses to the various areas around the plant. Material sampled includes air, water, milk, foods, vegetation, soil, fish, sediment, and direct radiation levels. Results from stations near the plant are compared with concentrations from control stations and with preoperational measurements to determine potential impacts of plant operations. 2 figs., 2 tabs

Bridging the gap between tribal risk perceptions and scientific decision-making for uranium legacy sites located in Native American communities

Science.gov (United States)

Joseph, C.; Waugh, W.; Glenn, E.; Chief, K.

2017-12-01

There are approximately 15,000 abandoned uranium mines (AUM) in the western United States, of which 500 AUMs are located in the Colorado Plateau Four-Corners region. Uranium mill tailings, referred to as legacy waste, compromise the largest volume of any category of radioactive waste in the nation. Today, the Department of Energy Legacy Management is responsible for long-term stewardship and maintenance of inactive uranium processing sites that have been remediated to prevent further migration and exposure of tailings to the environment and surrounding communities. In collaboration with the DOE-LM, I am investigating the impact of climate change and community adaptation on the long-term performance of disposal cell covers for uranium mill tailings located in Native American communities, as well as how these communities have adapted to and perceive these areas. I am interested in how abiotic engineered cell covers may be candidate sites for future conversion to vegetated evapotranspirative caps for arid to semi-arid climates. The objectives are to: 1) assess above-ground tissue of plants encroaching engineered cell covers for concentrations of uranium, radium, selenium, molybdenum, thorium, arsenic, lead, and manganese and compare them to control sites; 2) determine if above-cell plant tissue is accumulating to toxic levels that may create an exposure pathway, 3) identify climate scenarios for site locations and determine how short-and long-scale climate projections will influence spatial and temporal plant distribution for specific woody species; and 4) evaluate the risk perceptions of Hopi villages located five miles downstream of one site location. To date, risk perception and stakeholder outreach to the Hopi communities has been absent. This study will help inform how land use, water use, and sustenance practices may contribute to environmental health disparities for one of the few tribes that has maintained physical continuity within their ancestral homeland.

Detection of potato mop-top virus in soils and potato tubers using bait-plant bioassay, ELISA and RT-PCR.

Science.gov (United States)

Arif, Muhammad; Ali, Murad; Rehman, Anayatur; Fahim, Muhammad

2014-01-01

The hilly region of Northwest of Pakistan is leading seed potato producing areas of the country. Soil and plant samples were collected from the region and tested for PMTV using both conventional and molecular techniques. The bait plants exhibited PMTV-characteristic v-shaped yellow leaf markings in Nicotiana debneyi plants grown in putative viruliferious soils from 20/26 locations. The results were confirmed by back inoculation of sap from both roots and leaves of bait plant on indicator hosts (N. debneyi, Nicotiana benthamiana). The root samples of bait plants grown in soils of 25 locations and leaves of 24 locations reproduced systemic infection on indicator hosts upon back inoculation. The virus was identified in bait plants grown in soils from 25/26 locations using double antibody sandwich-enzyme linked immunosorbent assay (DAS)-ELISA and reverse transcription and polymerase chain reaction (RT-PCR) methods. The products of the 566bp were amplified from coat protein region of PMTV RNA 3 in both root and leaf samples of baited plants. The virus was detected in 10 potato cultivars commercially grown in the region using DAS-ELISA and RT-PCR. The virus was also detected in zoospores of Spongospora subterranea derived from the peels of selected scabby tubers using triple antibody sandwich (TAS)-ELISA. The results indicate that a bait plant bioassay, infectivity assay, ELISA and RT-PCR can detect PMTV in roots and leaves of baited plants, field samples, zoospores of S. subterranea and tubers of 10 potato cultivars commercially grown in the region. Copyright © 2013 Elsevier B.V. All rights reserved.

Piping analysis for the life extension of Heavy Water Plant, Kota

International Nuclear Information System (INIS)

Mishra, Rajesh; Soni, R.S.; Kushwaha, H.S.; Venkat Raj, V.

2001-02-01

Heavy water production in India has achieved many milestones in the past. One of the most successfully running heavy water plant situated at Kota (Rajasthan) is on the verge of completion of its design life in near future. Heavy Water Plant, Kota is hydrogen sulfide based plant. Various exercises have been planned with an aim to assess the fatigue usage for the various components of these plants in order to extend their life. Considering the process parameters and past history of the plant performance, 25 process critical nozzle locations and connected piping systems are identified. Analyses have been carried out for these critical piping systems for mainly two kinds of loading, viz. sustained loads and the expansion loads. The static analysis has been carried out to find the induced stress levels due to sustained as well as thermal expansion loading as per the design code ANSI B31.3. Due consideration is given to the design corrosion allowance while evaluating the stresses due to sustained loads. At the locations where induced stresses (S 1 ) due to the sustained loads are exceeding the allowable limits (S h ), exercises have been carried out considering the reduced corrosion allowance value. This strategy is adopted due to the fact that the corrosion measurements carried out at site at various critical locations show a very low rate of corrosion. Where it is found that system is getting qualified with reduced corrosion allowance values, it is recommended to keep that location under periodic monitoring. The strategy adopted for carrying out the analysis for thermal expansion loading is to qualify the system as per the code allowable value (S a ). Where it is found that the stresses are more than the allowable value, credit of liberal allowable value as suggested in the code i.e., with the addition of the term (S h -S 1 ) to the allowable stress (S a ) value, has been taken. If at any location, it is found that the problem of high thermal stress still persists, the

Location-based prospective memory.

Science.gov (United States)

O'Rear, Andrea E; Radvansky, Gabriel A

2018-02-01

This study explores location-based prospective memory. People often have to remember to do things when in a particular location, such as buying tissues the next time they are in the supermarket. For event cognition theory, location is important for structuring events. However, because event cognition has not been used to examine prospective memory, the question remains of how multiple events will influence prospective memory performance. In our experiments, people delivered messages from store to store in a virtual shopping mall as an ongoing task. The prospective tasks were to do certain activities in certain stores. For Experiment 1, each trial involved one prospective memory task to be done in a single location at one of three delays. The virtual environment and location cues were effective for prospective memory, and performance was unaffected by delay. For Experiment 2, each trial involved two prospective memory tasks, given in either one or two instruction locations, and to be done in either one or two store locations. There was improved performance when people received instructions from two locations and did both tasks in one location relative to other combinations. This demonstrates that location-based event structure influences how well people perform on prospective memory tasks.

Concentrations of manganese and iron in some woody and herbs plants

Directory of Open Access Journals (Sweden)

Stanković Dragica M.

2011-01-01

Full Text Available Heavy metals are the substances that indicate environmental pollution. The plants polluted with heavy metals may endanger natural environment and cause health problems in humans. In our multidisciplinary research of the concentrations of pollutants in forest ecosystems and natural environment in Belgrade, we examined the contents of heavy metals essential for plants but harmful in greater concentrations on a long-term basis. The fact that heavy metals manganese and iron are accumulated in plants to the greatest extent focused our work on determination of the level of concentrations of Mn and Fe in the vegetative parts of 8 plant types on three locations on the Avala Mountain and one location in the centre of the city of Belgrade. The analyses of heavy metals contents in plants were performed by the method of flame atomic absorption spectrophotometry. The examination of the existence of important differences between the average values was performed by implementation of Duncan’s test for the level of significance of 95%. The current contents of heavy metals in plants in the area of the protected natural resource Avala do not represent danger that would presently cause notable damage to forests but show the tendency of the increase of concentrations. Therefore, this issue should be constantly monitored.

CONCEPT-5 user's manual. [Power plant costs

Energy Technology Data Exchange (ETDEWEB)

Hudson, C.R. II

1979-01-01

The CONCEPT computer code package was developed to provide conceptual capital cost estimates for nuclear-fueled and fossil-fired power plants. Cost estimates can be made as a function of plant type, size, location, and date of initial operation. The output includes a detailed breakdown of the estimate into direct and indirect costs similar to the accounting system described in document NUS--531. Cost models are currently provided in CONCEPT 5 for single- and multiunit pressurized-water reactors, boiling-water reactors, and cost-fired plants with and without flue gas desulfurization equipment.

Conceptual designs of pressurized fluidized bed and pulverized coal fired power plants

International Nuclear Information System (INIS)

Doss, H.S.; Bezella, W.A.; Hamm, J.R.; Pietruszkiewicz, J.

1984-01-01

This paper presents the major technical and economic characteristics of steam and air-cooled pressurized fluidized bed (PFB) power plant concepts, along with the characteristics of a pulverized coal fired power plant equipped with an adipic acid enhanced wet-limestone flue gas desulfurization system. Conceptual designs for the three plants were prepared to satisfy a set of common groundrules developed for the study. Grassroots plants, located on a generic plant site were assumed. The designs incorporate technologies projected to be commercial in the 1990 time frame. Power outputs, heat rates, and costs are presented

Application of environmentally-corrected fatigue curves to nuclear power plant components

International Nuclear Information System (INIS)

Ware, A.G.; Morton, D.K.; Nitzel, M.E.

1996-01-01

Recent test data indicate that the effects of the light water reactor (LWR) environment could significantly reduce the fatigue resistance of materials used in the reactor coolant pressure boundary components of operating nuclear power plants. Argonne National Laboratory has developed interim fatigue curves based on test data simulating LWR conditions, and published them in NUREG/CR-5999. In order to assess the significance of these interim fatigue curves, fatigue evaluations of a sample of the components in the reactor coolant pressure boundary of LWRs were performed. The sample consists of components from facilities designed by each of the four US nuclear steam supply system vendors. For each facility, six locations were studied including two locations on the reactor pressure vessel. In addition, there are older vintage plants where components of the reactor coolant pressure boundary were designed to codes that did not require an explicit fatigue analysis of the components. In order to assess the fatigue resistance of the older vintage plants, an evaluation was also conducted on selected components of three of these plants. This paper discusses the insights gained from the application of the interim fatigue curves to components of seven operating nuclear power plants

Integration of Biorefineries and Nuclear Cogeneration Power Plants - A Preliminary Analysis

Energy Technology Data Exchange (ETDEWEB)

Greene, Sherrell R [ORNL; Flanagan, George F [ORNL; Borole, Abhijeet P [ORNL

2009-03-01

Biomass-based ethanol and nuclear power are two viable elements in the path to U.S. energy independence. Numerous studies suggest nuclear power could provide a practical carbon-free heat source alternative for the production of biomass-based ethanol. In order for this coupling to occur, it is necessary to examine the interfacial requirements of both nuclear power plants and bioethanol refineries. This report describes the proposed characteristics of a small cogeneration nuclear power plant, a biochemical process-based cellulosic bioethanol refinery, and a thermochemical process-based cellulosic biorefinery. Systemic and interfacial issues relating to the co-location of either type of bioethanol facility with a nuclear power plant are presented and discussed. Results indicate future co-location efforts will require a new optimized energy strategy focused on overcoming the interfacial challenges identified in the report.

Integration of Biorefineries and Nuclear Cogeneration Power Plants - A Preliminary Analysis

International Nuclear Information System (INIS)

Greene, Sherrell R.; Flanagan, George F.; Borole, Abhijeet P.

2009-01-01

Biomass-based ethanol and nuclear power are two viable elements in the path to U.S. energy independence. Numerous studies suggest nuclear power could provide a practical carbon-free heat source alternative for the production of biomass-based ethanol. In order for this coupling to occur, it is necessary to examine the interfacial requirements of both nuclear power plants and bioethanol refineries. This report describes the proposed characteristics of a small cogeneration nuclear power plant, a biochemical process-based cellulosic bioethanol refinery, and a thermochemical process-based cellulosic biorefinery. Systemic and interfacial issues relating to the co-location of either type of bioethanol facility with a nuclear power plant are presented and discussed. Results indicate future co-location efforts will require a new optimized energy strategy focused on overcoming the interfacial challenges identified in the report.

Encapsulation plant preliminary design, phase 2. Repository connected facility

International Nuclear Information System (INIS)

Kukkola, T.

2006-12-01

The disposal facility of the spent nuclear fuel will be located in Olkiluoto. The encapsulation plant is a part of the disposal facility. In this report, an independent encapsulation plant is located above the underground repository. In the encapsulation plant, the spent fuel is received and treated for disposal. In the fuel handling cell, the spent fuel assemblies are unloaded from the spent fuel transport casks and loaded into the disposal canisters. The gas atmosphere of the disposal canister is changed, the bolted inner canister lid is closed, and the electron beam welding method is used to close the lid of the outer copper canister. The disposal canisters are cleaned and transferred into the buffer store after the machining and inspection of the copper lid welds. From the buffer store, the disposal canisters are transferred into the repository spaces by help of the canister lift. All needed stages of operation are to be performed safely without any activity releases or remarkable personnel doses. The bentonite block interim storage is associated with the encapsulation plant. The bentonite blocks are made from bentonite powder. The bentonite blocks are used as buffer material around the disposal canister in the deposition hole. The average production rate of the encapsulation plant is 40 canisters per year. The nominal maximum production capacity is 100 canisters per year in one shift operation. (orig.)

[Host plants of Aphis gossypii (Aphididae), vector of virus of Cucumis melo melon (Cucurbitaceae) in Costa Rica].

Science.gov (United States)

Sánchez, M V; Agüero, R; Rivera, C

2001-03-01

Plant species associated with commercial melon crops and surrounding areas were examined to identity the natural host plants of Aphis gossypii Glover. The study was conducted in two farms located in different melon production areas and plant life zones of Costa Rica. Plant species diversity, percent coverage and distribution over time were recorded during one year. Differences between locations were observed. A total of 86 plant species (49 families) and 72 plant species (40 families) were identified associated to the crop in farms A and B, respectively. In both farms a total of 24 species plants (16 families) were colonized by A. gossypii and 16 (10 families) are new reports of host plant species for this aphid. The new reports are: Justicia comata, Tetramerium nervosum, Alternanthera pubiflora, Cassia massoni, C. reticulata, Cleome viscosa, C. spinosa, Croton argenteus, Caperonia palustris, Chamaesyce gyssopilopia, Phyllantus amarus, Sida decumbens, Ludwigia erecta, Passiflora foetida, Guazuma ulmifolia and Corchorus orinocensis.

Analysis and comparison between a concentrating solar and a photovoltaic power plant

International Nuclear Information System (INIS)

Desideri, Umberto; Campana, Pietro Elia

2014-01-01

Highlights: • The performance of CSP and PV plants were compared with similar assumptions. • The influence of the site on the performance of CSP and PV plants is determined. • CSP plants performance is always higher in locations where DNI is prevailing. • CSP levelized electricity costs are generally lower than those from PV plants. • PV plants may produce larger amounts of electricity where the DNI is not prevailing. - Abstract: Solar energy is a source, which can be exploited in two main ways to generate power: direct conversion into electric energy using photovoltaic panels and by means of a thermodynamic cycle. In both cases the amount of energy, which can be converted, is changing daily and seasonally, causing a discontinuous electricity production. In order to limit this drawback, concentrated solar power plants (CSP) and photovoltaic plants (PV) can be equipped with a storage system that can be configured not only for covering peak-loads but also for the base-load after the sunset or before the sunrise. In CSP plants it is the sun’s thermal energy to be stored, whereas in PV applications it is the electrical energy to be stored in batteries, although this is not economically and environmentally feasible in large-scale power plants. The main aim of this paper is to study the performance of concentrated solar power plants equipped with molten salts thermal storage to cover a base load of 3 MW el . In order to verify the possibility of storing effectively the thermal energy and to design a plant for base load operation, two locations were chosen for the study: Gela in southern Italy, and Luxor in Egypt. The electricity production of the CSP facilities has been analyzed and then compared with the electricity production of PV plants. Two different comparisons were done, one by sizing the PV plant to provide the same peak power and one using the same collectors surface. This paper has also highlighted some important issues in site selection and in

77 FR 47121 - Calvert Cliffs Nuclear Power Plant, LLC; Calvert Cliffs Nuclear Power Plant, Units 1 and 2...

Science.gov (United States)

2012-08-07

... for Nuclear Power Plant Personnel,'' endorses the Nuclear Energy Institute (NEI) report NEI 06-11...(c)(25). Pursuant to 10 CFR 51.22(b), no environmental impact statement or environmental assessment... hereafter in effect. The facility consists of two pressurized-water reactors (PWRs) located in Calvert...

Internet Geo-Location

Science.gov (United States)

2017-12-01

INTERNET GEO-LOCATION DUKE UNIVERSITY DECEMBER 2017 FINAL TECHNICAL REPORT APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED STINFO COPY AIR...REPORT TYPE FINAL TECHNICAL REPORT 3. DATES COVERED (From - To) MAY 2014 – MAY 2017 4. TITLE AND SUBTITLE INTERNET GEO-LOCATION 5a. CONTRACT...of SpeedTest servers that are used by end users to measure the speed of their Internet connection. The servers log the IP address and the location

MAPPING ALPINE VEGETATION LOCATION PROPERTIES BY DENSE MATCHING

Directory of Open Access Journals (Sweden)

R. Niederheiser

2016-06-01

Full Text Available Highly accurate 3D micro topographic mapping in mountain research demands for light equipment and low cost solutions. Recent developments in structure from motion and dense matching techniques provide promising tools for such applications. In the following, the feasibility of terrestrial photogrammetry for mapping topographic location properties of sparsely vegetated areas in selected European mountain regions is investigated. Changes in species composition at alpine vegetation locations are indicators of climate change consequences, such as the pronounced rise of average temperatures in mountains compared to the global average. Better understanding of climate change effects on plants demand for investigations on a micro-topographic scale. We use professional and consumer grade digital single-lens reflex cameras mapping 288 plots each 3 x 3 m on 18 summits in the Alps and Mediterranean Mountains within the GLORIA (GLobal Observation Research Initiative in Alpine environments network. Image matching tests result in accuracies that are in the order of millimetres in the XY-plane and below 0.5 mm in Z-direction at the second image pyramid level. Reconstructing vegetation proves to be a challenge due to its fine and small structured architecture and its permanent movement by wind during image acquisition, which is omnipresent on mountain summits. The produced 3D point clouds are gridded to 6 mm resolution from which topographic parameters such as slope, aspect and roughness are derived. At a later project stage these parameters will be statistically linked to botanical reference data in order to conclude on relations between specific location properties and species compositions.

Location Privacy with Randomness Consistency

Directory of Open Access Journals (Sweden)

Wu Hao

2016-10-01

Full Text Available Location-Based Social Network (LBSN applications that support geo-location-based posting and queries to provide location-relevant information to mobile users are increasingly popular, but pose a location-privacy risk to posts. We investigated existing LBSNs and location privacy mechanisms, and found a powerful potential attack that can accurately locate users with relatively few queries, even when location data is well secured and location noise is applied. Our technique defeats previously proposed solutions including fake-location detection and query rate limits.

Intergrated plant safety assessment. Systematic evaluation program. Palisades plant, Consumers Power Company, Docket No. 50-255. Final report

International Nuclear Information System (INIS)

1982-10-01

The Nuclear Regulatory Commission (NRC) has published its Final Integrated Plant Safety Assessment Report (IPSAR) (NUREG-0820), under the scope of the Systematic Evaluation Program (SEP), for Consumers Power Company's Palisades Plant located in Covert, Van Buren County, Michigan. The SEP was initiated by the NRC to review the design of older operating nuclear reactor plants to reconfirm and document their safety. This report documents the review completed under the SEP for the Palisades Plant. The review has provided for (1) as assessment of the significance of differences between current technical positions on selected safety issues and those that existed when the Palisades Plant was licensed, (2) a basis for deciding on how these differences should be resolved in an integrated plant review, and (3) a documented evaluation of plant safety when all supplements to the Final IPSAR and the Safety Evaluation Report for converting the license from a provisional to a full-term license have been issued. The report also addresses the comments and recommendations made by the Advisory Committee on Reactor Safeguards in connection with its review of the Draft Report, issued in April 1982

Neutron Measurements At Hanford's Plutonium Finishing Plant

International Nuclear Information System (INIS)

Conrady, Matthew M.; Berg, Randal K.; Scherpelz, Robert I.; Rathbone, Bruce A.

2009-01-01

The Pacific Northwest National Laboratory (PNNL) conducted neutron measurements at Hanford's Plutonium Finishing Plant (PFP). The measurements were performed to evaluate the performance of the Hanford Standard Dosimeter (HSD) and the 8816 TLD component of the Hanford Combination Neutron Dosimeter (HCND) in the neutron fields responsible for worker neutron exposures. For this study, TEPC detectors and multisphere spectrometers were used to measure neutron dose equivalent rate, and multispheres were used to measure average neutron energy. Water-filled phantoms holding Hanford dosimeters were positioned at each measurement location. The phantoms were positioned in the same location where a multisphere measurement was taken and TEPCs were also positioned there. Plant survey meters were also used to measure neutron dose rates at all locations. Three measurement locations were chose near the HC-9B glovebox in room 228A of Building 234-5. The multisphere spectrometers measured average neutron energies in the range of 337 to 555 keV at these locations. Personal dose equivalent, Hp(10)n, as measured by the multisphere and TEPC, ranged from 2.7 to 9.7 mrem/h in the three locations. Effective dose assuming a rotational geometry (EROT) was substantially lower than Hp(10), ranging from 1.3 to 3.6 mrem/h. These values were lower than the reported values from dosimeters exposed on a rotating phantom. Effective dose assuming an AP geometry (EAP) was also substantially lower than Hp(10), ranging from 2.3 to 6.5 mrem/h. These values were lower than the reported values from the dosimeters on slab phantoms. Since the effective dose values were lower than reported values from dosimeters, the dosimeters were shown to be conservative estimates of the protection quantities.

Life cycle assessment of a HYSOL concentrated solar power plant: Analyzing the effect of geographic location

NARCIS (Netherlands)

Corona, B.; Ruiz, Diego; San Miguel, Guillermo

2016-01-01

Concentrating Solar Power (CSP) technology is developing in order to achieve higher energy efficiency, reduced economic costs, and improved firmness and dispatchability in the generation of power on demand. To this purpose, a research project titled HYSOL has developed a new power plant, consisting

Germination and field survival of white-topped pitcher plant seeds

Science.gov (United States)

Kristina Connor; Hilliard Gibbs

2012-01-01

A study was initiated to determine longevity of white-topped pitcher plant (Sarracenia leucophylla, Raf.) seeds in the field and in cold storage. Thirty seed pods were harvested in August 2009 from plants located in Alabama 38 miles from the Gulf Coast. Of the 10,000+ seeds extracted from the pods, some were buried outside in screen-wire bags and...

Environmental monitoring at the Savannah River Plant. Annual report, 1974

International Nuclear Information System (INIS)

Ashley, C.; Zeigler, C.C.

1975-08-01

Results obtained from the environmental radioactivity monitoring program at the Savannah River Plant (SRP) during 1974 are summarized. A brief discussion of plant releases to the environment and radioactivity detected in the environment is presented in the following text, figures, and tables. The appendices contain tables of results from environmental samples analyses, sensitivities of laboratory analyses, and maps of sampling locations. (auth)

Host location behavior of Cotesia plutellae Kurdjumov (Hymenoptera: Braconidae) in ambient and moderately elevated ozone in field conditions

International Nuclear Information System (INIS)

Pinto, D.M.; Himanen, S.J.; Nissinen, A.; Nerg, A.-M.; Holopainen, J.K.

2008-01-01

In field O 3 -enrichment experiments increased herbivore densities have been reported, which could be due to negatively affected host location behavior of natural enemies. We addressed the impact of doubling background O 3 on the host location of the parasitoid Cotesia plutellae by conducting 24-h trials in an open-air O 3 -fumigation system during two consecutive years. Two circles (radii 1.40 and 4.00 m) of Plutella xylostella-infested potted cabbage plants were placed in the O 3 and ambient plots. Female wasps were released into each plot from the center, and observed 5 times over a 24-h period to assess their host location capability. Thereafter, plants were kept in laboratory conditions until larvae pupation to determine parasitism rates. No significant differences were detected between ambient and O 3 -enriched environments either in the number of wasps found in the field, or in the percentages of parasitized larvae. This suggests that moderately elevated O 3 will not affect the behavior of this parasitoid. - Atmospheric ozone increases do not directly affect the biological control of the cabbage pest, Plutella xylostella

Host location behavior of Cotesia plutellae Kurdjumov (Hymenoptera: Braconidae) in ambient and moderately elevated ozone in field conditions

Energy Technology Data Exchange (ETDEWEB)

Pinto, D.M. [Department of Environmental Science, University of Kuopio, PO Box 1627, FIN-70211 Kuopio (Finland)], E-mail: delia.pinto@uku.fi; Himanen, S.J. [Department of Environmental Science, University of Kuopio, PO Box 1627, FIN-70211 Kuopio (Finland); Nissinen, A. [Department of Environmental Science, University of Kuopio, PO Box 1627, FIN-70211 Kuopio (Finland); Agrifood Research Finland, Plant Protection, FIN-31600 Jokioinen (Finland); Nerg, A.-M.; Holopainen, J.K. [Department of Environmental Science, University of Kuopio, PO Box 1627, FIN-70211 Kuopio (Finland)

2008-11-15

In field O{sub 3}-enrichment experiments increased herbivore densities have been reported, which could be due to negatively affected host location behavior of natural enemies. We addressed the impact of doubling background O{sub 3} on the host location of the parasitoid Cotesia plutellae by conducting 24-h trials in an open-air O{sub 3}-fumigation system during two consecutive years. Two circles (radii 1.40 and 4.00 m) of Plutella xylostella-infested potted cabbage plants were placed in the O{sub 3} and ambient plots. Female wasps were released into each plot from the center, and observed 5 times over a 24-h period to assess their host location capability. Thereafter, plants were kept in laboratory conditions until larvae pupation to determine parasitism rates. No significant differences were detected between ambient and O{sub 3}-enriched environments either in the number of wasps found in the field, or in the percentages of parasitized larvae. This suggests that moderately elevated O{sub 3} will not affect the behavior of this parasitoid. - Atmospheric ozone increases do not directly affect the biological control of the cabbage pest, Plutella xylostella.

Multilevel Flow Modeling for Nuclear Power Plant Diagnosis

DEFF Research Database (Denmark)

Gola, G; Lind, Morten; Thunem, Harald P-J

2012-01-01

, especially if extended to the whole plant. Monitoring plant performances by means of data reconciliation techniques has proved successful to detect anomalies during operation, provide early warnings and eventually schedule maintenance. At the same time, the large amount of information provided by large...... detected anomalies. The combination of a data reconciliation system and the Multilevel Flow Modeling approach is illustrated with regard to the secondary loop of the Loviisa-2 Pressurized Water Reactor located in Finland....

Diversity of Endophytic Fungi from Red Ginger (Zingiber officinale Rosc. Plant and Their Inhibitory Effect to Fusarium oxysporum Plant Pathogenic Fungi

Directory of Open Access Journals (Sweden)

SIHEGIKO KANAYA

2013-09-01

Full Text Available Indonesia has been known as a country with high medicinal plant diversity. One of the most common medicinal plant from Indonesia is red ginger (Zingiber officinale Rosc.. Nevertheless, limited studies of endophytic fungi associated with these medicinal plants are hitherto available. The objectives of this research were to study the diversity of endophytic fungi on red ginger and to analyze their potential as a source of antifungal agent. All parts of plant organs such as leaf, rhizome, root, and stem were subjected for isolation. Fungal identification was carried out by using a combination of morphological characteristic and molecular analysis of DNA sequence generated from ITS rDNA region. Thirty endophytic fungi were successfully isolated from leaf, rhizome, root, and stem of red ginger plant. Antagonistic activity was tested against Fusarium oxysporum, a pathogenic fungus on plants, using an antagonistic assay. Based on this approach, the fungi were assigned as Acremonium macroclavatum, Beltraniella sp., Cochliobolus geniculatus and its anamorphic stage Curvularia affinis, Fusarium solani, Glomerella cingulata, and its anamorphic stage Colletotrichum gloeosporoides, Lecanicillium kalimantanense, Myrothecium verrucaria, Neonectria punicea, Periconia macrospinosa, Rhizopycnis vagum, and Talaromyces assiutensis. R. vagum was found specifically on root whereas C. affinis, L. kalimantanense, and M. verrucaria were found on stem of red ginger plant. A. macroclavatum was found specifically in red ginger plant’s organ which located under the ground, whereas C. affinis was found from shoot or organ which located above the ground. The antagonistic activity of isolated endophytic fungi against F. oxysporum varied with the inhibition value range from 1.4 to 68.8%. C. affinis (JMbt7, F. solani (JMd14, and G. cingulata (JMr2 had significantly high antagonistic activity with the value above 65%; and R. vagum (JMa4 and C. geniculatus (JMbt9 had

Herbivore-induced plant volatiles and tritrophic interactions across spatial scales.

Science.gov (United States)

Aartsma, Yavanna; Bianchi, Felix J J A; van der Werf, Wopke; Poelman, Erik H; Dicke, Marcel

2017-12-01

Herbivore-induced plant volatiles (HIPVs) are an important cue used in herbivore location by carnivorous arthropods such as parasitoids. The effects of plant volatiles on parasitoids have been well characterised at small spatial scales, but little research has been done on their effects at larger spatial scales. The spatial matrix of volatiles ('volatile mosaic') within which parasitoids locate their hosts is dynamic and heterogeneous. It is shaped by the spatial pattern of HIPV-emitting plants, the concentration, chemical composition and breakdown of the emitted HIPV blends, and by environmental factors such as wind, turbulence and vegetation that affect transport and mixing of odour plumes. The volatile mosaic may be exploited differentially by different parasitoid species, in relation to species traits such as sensory ability to perceive volatiles and the physical ability to move towards the source. Understanding how HIPVs influence parasitoids at larger spatial scales is crucial for our understanding of tritrophic interactions and sustainable pest management in agriculture. However, there is a large gap in our knowledge on how volatiles influence the process of host location by parasitoids at the landscape scale. Future studies should bridge the gap between the chemical and behavioural ecology of tritrophic interactions and landscape ecology. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Ranstad - A new uranium-processing plant

Energy Technology Data Exchange (ETDEWEB)

Peterson, A [AB Atomenergi, Stockholm (Sweden)

1967-06-15

A short outline is given of the decisions concerning the erection and operation of the Ranstad mill which was recently taken into operation. It is followed by a brief description of the geological conditions and the planning of the mining system, plant location, and the factory. The main part of the paper describes processes and equipment of the plant which has a capacity to treat approx. 850 000 tons of low-grade ore (alum shale) per year. The operational experience so far is also reviewed. The economy of uranium production at Ranstad is discussed and some development possibilities are indicated. (author)

Underground siting of nuclear power plants: potential benefits and penalties

International Nuclear Information System (INIS)

Allensworth, J.A.; Finger, J.T.; Milloy, J.A.; Murfin, W.B.; Rodeman, R.; Vandevender, S.G.

1977-08-01

The potential for improving nuclear power safety is analyzed by siting plants underground in mined cavities or by covering plants with fill earth after construction in an excavated cut. Potential benefits and penalties of underground plants are referenced to analogous plants located on the surface. Three representative regional sites having requisite underground geology were used to evaluate underground siting. The major factors which were evaluated for all three sites were: (1) containment of radioactive materials, (2) transport of groundwater contamination, and (3) seismic vulnerability. External protection, plant security, feasibility, operational considerations, and cost were evaluated on a generic basis. Additionally, the national availability of sites having the requisite geology for both underground siting concepts was determined

Off-stream Pumped Storage Hydropower plant to increase renewable energy penetration in Santiago Island, Cape Verde

Science.gov (United States)

Barreira, Inês; Gueifão, Carlos; Ferreira de Jesus, J.

2017-04-01

In order to reduce the high dependence on imported fuels and to meet the ongoing growth of electricity demand, Cape Verde government set the goal to increase renewable energy penetration in Santiago Island until 2020. To help maximize renewable energy penetration, an off-stream Pumped Storage Hydropower (PSH) plant will be installed in Santiago, in one of the following locations: Chã Gonçalves, Mato Sancho and Ribeira dos Picos. This paper summarizes the studies carried out to find the optimal location and connection point of the PSH plant in Santiago’s electricity network. This goal was achieved by assessing the impact of the PSH plant, in each location, on power system stability. The simulation tool PSS/E of Siemens was used to study the steady-state and dynamic behavior of the future (2020) Santiago MV grid. Different scenarios of demand and renewable resources were created. Each hydro unit of the PSH plant was modeled as an adjustable speed reversible turbine employing a DFIM. The results show that Santiago’s grid with the PSH plant in Chã Gonçalves is the one that has the best performance.

Socio-economic effects of a HYSOL CSP plant located in different countries: An input output analysis

NARCIS (Netherlands)

Corona, B.; López, A.; San Miguel, G.

2016-01-01

The aim of this paper is to estimate the socioeconomic effects associated with the production of electricity by a CSP plant with HYSOL configuration, using Input Output Analysis. These effects have been estimated in terms of production of Goods and Services (G&S), multiplier effect, value added,

Smartphones as locative media

CERN Document Server

Frith, Jordan

2015-01-01

Smartphone adoption has surpassed 50% of the population in more than 15 countries, and there are now more than one million mobile applications people can download to their phones. Many of these applications take advantage of smartphones as locative media, which is what allows smartphones to be located in physical space. Applications that take advantage of people's location are called location-based services, and they are the focus of this book. Smartphones as locative media raise important questions about how we understand the complicated relationship between the Internet and physical space

Dealing with Insufficient Location Fingerprints in Wi-Fi Based Indoor Location Fingerprinting

Directory of Open Access Journals (Sweden)

Kai Dong

2017-01-01

Full Text Available The development of the Internet of Things has accelerated research in the indoor location fingerprinting technique, which provides value-added localization services for existing WLAN infrastructures without the need for any specialized hardware. The deployment of a fingerprinting based localization system requires an extremely large amount of measurements on received signal strength information to generate a location fingerprint database. Nonetheless, this requirement can rarely be satisfied in most indoor environments. In this paper, we target one but common situation when the collected measurements on received signal strength information are insufficient, and show limitations of existing location fingerprinting methods in dealing with inadequate location fingerprints. We also introduce a novel method to reduce noise in measuring the received signal strength based on the maximum likelihood estimation, and compute locations from inadequate location fingerprints by using the stochastic gradient descent algorithm. Our experiment results show that our proposed method can achieve better localization performance even when only a small quantity of RSS measurements is available. Especially when the number of observations at each location is small, our proposed method has evident superiority in localization accuracy.

Measurement of the Portsmouth Gaseous Diffusion Plant criticality accident alarm

International Nuclear Information System (INIS)

Tayloe, R.W. Jr.; D'Aquila, D.M.; McGinnis, R.B.

1991-01-01

The nuclear criticality accident radiation alarm system installed at the Portsmouth Gaseous Diffusion Plant was tested extensively at critical facilities located at the Los Alamos National Laboratory. The ability of the neutron scintillator radiation detection units to respond to a minimum accident of concern as defined in Standard ANSI/ANS-83.-1986 was demonstrated. Detector placement and the established trip point are based on shielding calculations performed by the Oak Ridge National Laboratory and criticality specialists at the Portsmouth plant. Based on these experiments and calculations, a detector trip point of 5 mrad/h in air is used. Any credible criticality accident is expected to produce neutron radiation fields >5 mrad/h in air at one or more radiation alarm locations. Each radiation alarm location has a cluster of three detectors that employs a two-out-of-three alarm logic. Earlier work focused on testing the alarm logic latching circuitry. This work was directed toward measurements involving the actual audible alarm signal delivered

Law Enforcement Locations

Data.gov (United States)

Kansas Data Access and Support Center — Law Enforcement Locations in Kansas Any location where sworn officers of a law enforcement agency are regularly based or stationed. Law enforcement agencies "are...

Plant Research Department annual report 2002

DEFF Research Database (Denmark)

2003-01-01

concentrations in the atmosphere. Finally, activities are increasing to establish systems thatoptimize the production of energy from biomass in order to promote sustainability in industrial societies. The department is divided into five research programmes that are linked through their individual expertise...... to the optimal use of crops. One programme is devoted to improve the market value of plant products. Plants with enhanced nutritional value or that contain novel renewable resources are designed to add value to the European Agro-Industries.A fifth programme ultimately is studying the effects of the future......The Plant Research Department at Risø National Laboratory has the unique opportunity to be the only life science department located in an environment that is largely dominated by physicists. In 2002 increasing numbers of projects have been initiated thatestablish interdisciplinary research in order...

Beaver herbivory on aquatic plants.

Science.gov (United States)

Parker, John D; Caudill, Christopher C; Hay, Mark E

2007-04-01

Herbivores have strong impacts on marine and terrestrial plant communities, but their impact is less well studied in benthic freshwater systems. For example, North American beavers (Castor canadensis) eat both woody and non-woody plants and focus almost exclusively on the latter in summer months, yet their impacts on non-woody plants are generally attributed to ecosystem engineering rather than herbivory. Here, we excluded beavers from areas of two beaver wetlands for over 2 years and demonstrated that beaver herbivory reduced aquatic plant biomass by 60%, plant litter by 75%, and dramatically shifted plant species composition. The perennial forb lizard's tail (Saururus cernuus) comprised less than 5% of plant biomass in areas open to beaver grazing but greater than 50% of plant biomass in beaver exclusions. This shift was likely due to direct herbivory, as beavers preferentially consumed lizard's tail over other plants in a field feeding assay. Beaver herbivory also reduced the abundance of the invasive aquatic plant Myriophyllum aquaticum by nearly 90%, consistent with recent evidence that native generalist herbivores provide biotic resistance against exotic plant invasions. Beaver herbivory also had indirect effects on plant interactions in this community. The palatable plant lizard's tail was 3 times more frequent and 10 times more abundant inside woolgrass (Scirpus cyperinus) tussocks than in spatially paired locations lacking tussocks. When the protective foliage of the woolgrass was removed without exclusion cages, beavers consumed nearly half of the lizard's tail leaves within 2 weeks. In contrast, leaf abundance increased by 73-93% in the treatments retaining woolgrass or protected by a cage. Thus, woolgrass tussocks were as effective as cages at excluding beaver foraging and provided lizard's tail plants an associational refuge from beaver herbivory. These results suggest that beaver herbivory has strong direct and indirect impacts on populations and

Map of the world's nuclear power plants

International Nuclear Information System (INIS)

Anon.

1977-01-01

A pull-out wall chart is presented showing on a coloured map the locations of the world's nuclear power plants and indicating the type of reactor and number of units. The information is also included in an accompanying table which lists the stations alphabetically. (U.K.)

Analysis of the location for peak heating in CHP based combined district heating systems

International Nuclear Information System (INIS)

Wang, Haichao; Lahdelma, Risto; Wang, Xin; Jiao, Wenling; Zhu, Chuanzhi; Zou, Pinghua

2015-01-01

Combined heat and power (CHP) is the main technology for providing the base load of district heating in China. However, CHP is not efficient for providing the peak load; instead, a peak boiler with high efficiency could be used to compensate the peak load. This paper studies how the location of the peak boiler can affect the energy efficiency and economic performance of such CHP based combined district heating system. Firstly, the connection mode and the control strategy for different peak heating locations are analyzed. Then the effect of the peak boiler's location on the initial investment of the network and the cost for distributing heat is studied. The objective is to place the peak boiler in a location where the overall costs are the smallest. Following this rule, the results indicate that the peak boiler should be located at the CHP plant if that allows using cheaper ‘self-use electricity’ in CHP for distributing the heat. However, if the market electricity price is used everywhere, or if energy efficiency is more emphasized, the location of the peak boiler should be closer to the users with dense heat loads. - Highlights: • Location for peak heating in the CHP based combined DH system is studied. • Regulation or control strategies for combined DH are summarized. • The heat load duration curve for combined DH is demonstrated. • Network design for combined DH with peak boiler outside of the CHP is analyzed

Heavy metal concentrations in a soil-plant-snail food chain along a terrestrial soil pollution gradient.

NARCIS (Netherlands)

Notten, M.J.M.; Oosthoek, A.; Rozema, J.; Aerts, R.

2005-01-01

We investigated concentrations of Zn, Cu, Cd and Pb in the compartments of a soil-plant (Urtica dioica)-snail (Cepaea nemoralis) food chain in four polluted locations in the Biesbosch floodplains, the Netherlands, and two reference locations. Total soil metal concentrations in the polluted locations

Pre-engineering assessment of Enersolve Demonstration Project. Dairy processing plant. Final report

Energy Technology Data Exchange (ETDEWEB)

1985-07-15

This study involved evaluation of a dairy processing plant to demonstrate energy conservation potential and developing a strategy to realize energy savings through retrofitting and revamping. The cheese and whey making plant of Agropur Cooperative Agro-Alimentaire located in Quebec was selected as a representative Canadian dairy processing plant. The pre-engineering assessment included a review of existing facility at the plant and plant operation, identification of plant equipment or process steps where substantial economic benefits would result from retrofitting and revamping, and estimation of budgetary cost for the subsequent engineering, procurement, construction management and monitoring of the retrofitted equipment. 3 figs., 2 tabs.

Transfer of radionuclides to plants[Radioecology

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Sven P. [Risoe National Lab., Roskilde (Denmark)

2006-04-15

Sampling of Water Horsetail and Bracken Fern including upper soil layer (0-10 cm) and water was carried out in Torahult, Sweden, in Almindingen on Bornholm, in Asserbo and Arresoe on Zealand and in Sdr. Hostrup and Nydam mose in Jutland. Furthermore, sampling was carried out in 2004 for seawater, seaweed and shrimps at locations in Danish waters at Bornholm (Svenskehavn), at Zealand (Klint), at Lolland/Falster (Guldborgsund) and on the west coast of Jutland (Hirtshals, Agger, Hvide Sande and Roemoe). Concentrations of gamma-emitting radionuclides and uranium were determined in Bracken Fern, Water Horsetail and soil samples. The concentration ratios (CR) are highest for {sup 40}K in both plant species and show the lowest variability across locations. The CR's for 40K range from 1 to 2, while the CR's for the other radionuclides range one to three orders of magnitude lower. The CR's for {sup 137}Cs show particularly high variability across locations. The CR's were analysed in a two-way ANOVA on the log-transformed values to test differences between plant species and radionuclides. The difference between radionuclides was highly significant, p<0.01, whereas the difference between plant species was not significant. The concentration ratios are listed by radionuclide showing geometric mean values and geometric standard deviations. Analyses were made of {sup 137}Cs and {sup 99}Tc in marine samples. Concentration ratios calculated from the analysed samples are presented. The concentration ratios for {sup 99}Tc agree with those reported elsewhere in the Indofern Project. The concentration ratios for {sup 137}Cs in Fucus show a correlation to salinity with higher values in low salinity water at Bornholm than in high salinity water on the west coast of Jutland. (LN)

Contrasting natural regeneration and tree planting in fourteen North American cities

Science.gov (United States)

David J. Nowak

2012-01-01

Field data from randomly located plots in 12 cities in the United States and Canada were used to estimate the proportion of the existing tree population that was planted or occurred via natural regeneration. In addition, two cities (Baltimore and Syracuse) were recently re-sampled to estimate the proportion of newly established trees that were planted. Results for the...

7 CFR 1124.7 - Pool plant.

Science.gov (United States)

2010-01-01

... agreement for other than Class I use) into ultra-pasteurized or aseptically-processed fluid milk products...) located within one or more States that require handlers to pay minimum prices for raw milk provided that... prices for raw milk. Subject to the following exclusions: (i) The plant is described in § 1124.7(a) or (b...

7 CFR 1032.7 - Pool plant.

Science.gov (United States)

2010-01-01

...-pasteurized or aseptically-processed fluid milk products. (c) A supply plant from which the quantity of bulk... one or more States that require handlers to pay minimum prices for raw milk provided that 25 percent... marketing area(s) located within one or more States that require handlers to pay minimum prices for raw milk...

Geographic information system-based healthcare waste management planning for treatment site location and optimal transportation routeing.

Science.gov (United States)

Shanmugasundaram, Jothiganesh; Soulalay, Vongdeuane; Chettiyappan, Visvanathan

2012-06-01

In Lao People's Democratic Republic (Lao PDR), a growth of healthcare centres, and the environmental hazards and public health risks typically accompanying them, increased the need for healthcare waste (HCW) management planning. An effective planning of an HCW management system including components such as the treatment plant siting and an optimized routeing system for collection and transportation of waste is deemed important. National government offices at developing countries often lack the proper tools and methodologies because of the high costs usually associated with them. However, this study attempts to demonstrate the use of an inexpensive GIS modelling tool for healthcare waste management in the country. Two areas were designed for this study on HCW management, including: (a) locating centralized treatment plants and designing optimum travel routes for waste collection from nearby healthcare facilities; and (b) utilizing existing hospital incinerators and designing optimum routes for collecting waste from nearby healthcare facilities. Spatial analysis paved the way to understand the spatial distribution of healthcare wastes and to identify hotspots of higher waste generating locations. Optimal route models were designed for collecting and transporting HCW to treatment plants, which also highlights constraints in collecting and transporting waste for treatment and disposal. The proposed model can be used as a decision support tool for the efficient management of hospital wastes by government healthcare waste management authorities and hospitals.

Application of neutron activation analysis method in leaves of Casearia obliqua medicinal plant

International Nuclear Information System (INIS)

Yamashita, Celina I.; Saiki, Mitiko; Sertie, Jaime A.A.

2005-01-01

The pharmacological properties of medicinal plants have been related to the presence of organic compounds, however elements are also known to have an important participation in the active compounds constitution process. In this study, instrumental neutron activation analysis (INAA) was applied to determine elements in leaves of Casearia obliqua medicinal plant collected at two different locations in the Atlantic Forest, Brazil, SP. Soil samples collected from where this plant was grown were also analyzed in order to verify if there is a correlation between the elements present in soils and plant leaves. Br, Ca, Cl, Co, Cr, Cs, Fe, K, La, Mn, Na, Rb, Sb, Sc and Zn were determined in C. obliqua leaves and the elements As, Ca, Ce, Eu, Fe, Hf, La, Lu, Nd, Rb, Sc, Sm, Tb, Th, U and Zn in soils. Soil samples collected from two different locations presented similar concentrations for most elements. Likewise, C. obliqua leaves collected from the two locations presented similar elemental contents. These results suggest that analysis of extracts from these leaf samples and the evaluation of their pharmacological activities should be carried out. Certified reference materials IAEA-Soil-7, USGS W-1, NIST 1573a Tomato Leaves and NIST 1515 Apple Leaves were analyzed and the quality of the obtained results was assured. (author)

Development of nuclear power plant diagnosis technique using neural networks

International Nuclear Information System (INIS)

Horiguchi, Masahiro; Fukawa, Naohiro; Nishimura, Kazuo

1991-01-01

A nuclear power plant diagnosis technique has been developed, called transient phenomena analysis, which employs neural network. The neural networks identify malfunctioning equipment by recognizing the pattern of main plant parameters, making it possible to locate the cause of an abnormality when a plant is in a transient state. In a case where some piece of equipment shows abnormal behavior, many plant parameters either directly or indirectly related to that equipment change simultaneously. When an abrupt change in a plant parameter is detected, changes in the 49 main plant parameters are classified into three types and a characteristic change pattern consisting of 49 data is defined. The neural networks then judge the cause of the abnormality from this pattern. This neural-network-based technique can recognize 100 patterns that are characterized by the causes of plant abnormality. (author)

Dispersion of pollutants, environmental externalities due to a pulverized coal power plant and their effect on the cost of electricity

International Nuclear Information System (INIS)

Czarnowska, Lucyna; Frangopoulos, Christos A.

2012-01-01

Energy conversion systems generate pollution that causes damages to the environment and the society. The objective of this work is to study the dispersion of pollutants and assess the environmental and social cost due to pollution from such a system. For this purpose, a pulverized coal power plant is selected. Using thermodynamic principles combined with empirical techniques, the quantities of pollutants emitted by the plant are estimated. Then, using the EcoSenseWeb software, which is based on the results of the ExternE project, the external environmental cost (externalities) of pollution is assessed. The plant is considered as located in four different cities in Poland and the externalities are calculated for each city separately. It is shown that the external environmental cost has a strong influence on the unit cost of electricity. In addition, the dispersion of pollutants is presented for the plant located in Olsztyn city. Furthermore, the plant is considered as located near the capitals of European countries and the environmental externalities are calculated for each city. The neighboring countries that are strongly affected by the plant in each particular city are identified. The sensitivity of the unit cost of electricity to certain important parameters is investigated. -- Highlights: ► The external cost of pollution has a significant impact on the cost of electricity. ► The results depend on the particular plant, location and level (local-global). ► Externalities make the installation of abatement equipment economical. ► The source location of emissions has a significant effect on the external cost. ► The transboundary pollution has a strong effect on the environmental cost.

Laser-based analytical monitoring in nuclear-fuel processing plants

International Nuclear Information System (INIS)

Hohimer, J.P.

1978-09-01

The use of laser-based analytical methods in nuclear-fuel processing plants is considered. The species and locations for accountability, process control, and effluent control measurements in the Coprocessing, Thorex, and reference Purex fuel processing operations are identified and the conventional analytical methods used for these measurements are summarized. The laser analytical methods based upon Raman, absorption, fluorescence, and nonlinear spectroscopy are reviewed and evaluated for their use in fuel processing plants. After a comparison of the capabilities of the laser-based and conventional analytical methods, the promising areas of application of the laser-based methods in fuel processing plants are identified

Location | FNLCR Staging

Science.gov (United States)

The Frederick National Laboratory for Cancer Research campus is located 50 miles northwest of Washington, D.C., and 50 miles west of Baltimore, Maryland, in Frederick, Maryland. Satellite locations include leased and government facilities extending s

Thermal performance of solar district heating plants in Denmark

DEFF Research Database (Denmark)

Furbo, Simon; Perers, Bengt; Bava, Federico

2014-01-01

The market for solar heating plants connected to district heating systems is expanding rapidly in Denmark. It is expected that by the end of 2014 the 10 largest solar heating plants in Europe will be located in Denmark. Measurements from 23 Danish solar heating plants, all based on flat plate solar...... collectors mounted on the ground, shows measured yearly thermal performances of the solar heating plants placed in the interval from 313 kWh/m² collector to 493 kWh/m² collector with averages for all plants of 411 kWh/m² collector for 2012 and 450 kWh/m² collector for 2013. Theoretical calculations show...... of the cost/performance ratio for solar collector fields, both with flat plate collectors and with concentrating tracking solar collectors. It is recommended to continue monitoring and analysis of all large solar heating plants to document the reliability of the solar heating plants. It is also recommended...

Diurnal adjustment in ultraviolet sunscreen protection is widespread among higher plants.

Science.gov (United States)

Barnes, Paul W; Flint, Stephan D; Tobler, Mark A; Ryel, Ronald J

2016-05-01

The accumulation of ultraviolet (UV)-absorbing compounds (flavonoids and related phenylpropanoids) in the epidermis of higher plants reduces the penetration of solar UV radiation to underlying tissues and is a primary mechanism of acclimation to changing UV conditions resulting from ozone depletion and climate change. Previously we reported that several herbaceous plant species were capable of rapid, diurnal adjustments in epidermal UV transmittance (T UV), but how widespread this phenomenon is among plants has been unknown. In the present study, we tested the generality of this response by screening 37 species of various cultivated and wild plants growing in four locations spanning a gradient of ambient solar UV and climate (Hawaii, Utah, Idaho and Louisiana). Non-destructive measurements of adaxial T UV indicated that statistically significant midday decreases in T UV occurred in 49 % of the species tested, including both herbaceous and woody growth forms, and there was substantial interspecific variation in the magnitude of these changes. In general, plants in Louisiana exhibited larger diurnal changes in T UV than those in the other locations. Moreover, across all taxa, the magnitude of these changes was positively correlated with minimum daily air temperatures but not daily UV irradiances. Results indicate that diurnal changes in UV shielding are widespread among higher plants, vary both within and among species and tend to be greatest in herbaceous plants growing in warm environments. These findings suggest that plant species differ in their UV protection "strategies" though the functional and ecological significance of this variation in UV sunscreen protection remains unclear at present.

Arsenic accumulation and speciation in plants from different habitats

OpenAIRE

Bergqvist, Claes; Greger, Maria

2012-01-01

This is the postprint version of the article. The published version of the article can be located here: http://www.sciencedirect.com/science/article/pii/S0883292711004914 Understanding As accumulation in plants is necessary in order to alleviate problems with As in the environment and to improve sustainable As phytotechnologies. To find suitable candidates for phytoremediation purposes and to investigate specific accumulation patterns due to growth habitat and plant groups, As accumulation...

Privacy for location-based services

CERN Document Server

Ghinita, Gabriel

2013-01-01

Sharing of location data enables numerous exciting applications, such as location-based queries, location-based social recommendations, monitoring of traffic and air pollution levels, etc. Disclosing exact user locations raises serious privacy concerns, as locations may give away sensitive information about individuals' health status, alternative lifestyles, political and religious affiliations, etc. Preserving location privacy is an essential requirement towards the successful deployment of location-based applications. These lecture notes provide an overview of the state-of-the-art in locatio

Pulsed nuclear power plant

International Nuclear Information System (INIS)

David, C.V.

1986-01-01

This patent describes a nuclear power plant. This power plant consists of: 1.) a cavity; 2.) a detonatable nuclear device in a central region of the cavity; 3.) a working fluid inside of the cavity; 4.) a method to denote a nuclear device inside of the cavity; 5.) a mechanical projection from an interior wall of the cavity for recoiling to absorb a shock wave produced by the detonation of the nuclear device and thereby protecting the cavity from damage. A plurality of segments defines a shell within the cavity and a plurality of shock absorbers, each connecting a corresponding segment to a corresponding location on the wall of the cavity. Each of these shock absorbers regulate the recoil action of the segments; and 6.) means for permitting controlled extraction of a quantity of hot gases from the cavity produced by the vaporization of the working fluid upon detonation of the nuclear device. A method of generating power is also described. This method consists of: 1.) introducing a quantity of water in an underground cavity; 2.) heating the water in the cavity to form saturated steam; 3.) detonating a nuclear device at a central location inside the cavity; 4.) recoiling plate-like elements inside the cavity away from the central location in a mechanically regulated and controlled manner to absorb a shock wave produced by the nuclear device detonation and thereby protect the underground cavity against damage; 5.) extracting a quantity of superheated steam produced by the detonation of the nuclear device; and 6.) Converting the energy in the extracted superheated steam into electrical power

Epigenetic variation in mangrove plants occurring in contrasting natural environment.

Directory of Open Access Journals (Sweden)

Catarina Fonseca Lira-Medeiros

2010-04-01

Full Text Available Epigenetic modifications, such as cytosine methylation, are inherited in plant species and may occur in response to biotic or abiotic stress, affecting gene expression without changing genome sequence. Laguncularia racemosa, a mangrove species, occurs in naturally contrasting habitats where it is subjected daily to salinity and nutrient variations leading to morphological differences. This work aims at unraveling how CpG-methylation variation is distributed among individuals from two nearby habitats, at a riverside (RS or near a salt marsh (SM, with different environmental pressures and how this variation is correlated with the observed morphological variation.Significant differences were observed in morphological traits such as tree height, tree diameter, leaf width and leaf area between plants from RS and SM locations, resulting in smaller plants and smaller leaf size in SM plants. Methyl-Sensitive Amplified Polymorphism (MSAP was used to assess genetic and epigenetic (CpG-methylation variation in L. racemosa genomes from these populations. SM plants were hypomethylated (14.6% of loci had methylated samples in comparison to RS (32.1% of loci had methylated samples. Within-population diversity was significantly greater for epigenetic than genetic data in both locations, but SM also had less epigenetic diversity than RS. Frequency-based (G(ST and multivariate (beta(ST methods that estimate population structure showed significantly greater differentiation among locations for epigenetic than genetic data. Co-Inertia analysis, exploring jointly the genetic and epigenetic data, showed that individuals with similar genetic profiles presented divergent epigenetic profiles that were characteristic of the population in a particular environment, suggesting that CpG-methylation changes may be associated with environmental heterogeneity.In spite of significant morphological dissimilarities, individuals of L. racemosa from salt marsh and riverside presented

Selection and Vegetative Propagation of Native Woody Plants for Water-Wise Landscaping

OpenAIRE

Rupp, Larry A; Varga, William A; Anderson, David

2011-01-01

Native woody plants with ornamental characteristics such as brilliant fall color, dwarf form, or glossy leaves have potential for use in water conserving urban landscapes. Individual accessions with one or more of these unique characteristics were identified based on the recommendations of a wide range of plant enthusiasts (both professional and amateur). Documentation of these accessions has been done through locating plants on-site where possible and then developing a record based on digita...

Organ accumulation and subcellular location of Cicer arietinum ST1 protein.

Science.gov (United States)

Albornos, Lucía; Cabrera, Javier; Hernández-Nistal, Josefina; Martín, Ignacio; Labrador, Emilia; Dopico, Berta

2014-07-01

The ST (ShooT Specific) proteins are a new family of proteins characterized by a signal peptide, tandem repeats of 25/26 amino acids, and a domain of unknown function (DUF2775), whose presence is limited to a few families of dicotyledonous plants, mainly Fabaceae and Asteraceae. Their function remains unknown, although involvement in plant growth, fruit morphogenesis or in biotic and abiotic interactions have been suggested. This work is focused on ST1, a Cicer arietinum ST protein. We established the protein accumulation in different tissues and organs of chickpea seedlings and plants and its subcellular localization, which could indicate the possible function of ST1. The raising of specific antibodies against ST1 protein revealed that its accumulation in epicotyls and radicles was related to their elongation rate. Its pattern of tissue location in cotyledons during seed formation and early seed germination, as well as its localization in the perivascular fibres of epicotyls and radicles, indicated a possible involvement in seed germination and seedling growth. ST1 protein appears both inside the cell and in the cell wall. This double subcellular localization was found in every organ in which the ST1 protein was detected: seeds, cotyledons and seedling epicotyls and radicles. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Encapsulation plant at Forsmark

International Nuclear Information System (INIS)

Nystroem, Anders

2007-08-01

SKB has already carried out a preliminary study of an encapsulation plant detached from Clab (Central interim storage for spent fuels). This stand-alone encapsulation plant was named FRINK and its assumed siting was the above-ground portion of the final repository, irrespective of the repository's location. The report previously presented was produced in cooperation with BNFL Engineering Ltd in Manchester and the fuel reception technical solution was examined by Gesellschaft fuer Nuklear-Service mbH (GNS) in Hannover and by Societe Generale pour les Techniques Nouvelles (SGN) in Paris. This report is an update of the earlier preliminary study report and is based on the assumption that the encapsulation plant and also the final repository will be sited in the Forsmark area. SKB's main alternative for siting the encapsulation plant is next to Clab. Planning of this facility is ongoing and technical solutions from the planning work have been incorporated in this report. An encapsulation plant placed in proximity to any final repository in Forsmark forms part of the alternative presentation in the application for permission to construct and operate an installation at Clab. The main technical difference between the planned encapsulation plant at Clab and an encapsulation plant at a final repository at Forsmark is how the fuel is managed and prepared before actual encapsulation. Fuel reception at the encapsulation plant in Forsmark would be dry, i.e. there would be no water-filled pools at the facility. Clab is used for verificatory fuel measurements, sorting and drying of the fuel before transport to Forsmark. This means that Clab will require a measure of rebuilding and supplementary equipment. In purely technical terms, the prospects for building an encapsulation plant sited at Forsmark are good. A description of the advantages and drawbacks of siting the encapsulation plant at Clab as opposed to any final repository at Forsmark is presented in a separate report

Encapsulation plant at Forsmark

Energy Technology Data Exchange (ETDEWEB)

Nystroem, Anders

2007-08-15

SKB has already carried out a preliminary study of an encapsulation plant detached from Clab (Central interim storage for spent fuels). This stand-alone encapsulation plant was named FRINK and its assumed siting was the above-ground portion of the final repository, irrespective of the repository's location. The report previously presented was produced in cooperation with BNFL Engineering Ltd in Manchester and the fuel reception technical solution was examined by Gesellschaft fuer Nuklear-Service mbH (GNS) in Hannover and by Societe Generale pour les Techniques Nouvelles (SGN) in Paris. This report is an update of the earlier preliminary study report and is based on the assumption that the encapsulation plant and also the final repository will be sited in the Forsmark area. SKB's main alternative for siting the encapsulation plant is next to Clab. Planning of this facility is ongoing and technical solutions from the planning work have been incorporated in this report. An encapsulation plant placed in proximity to any final repository in Forsmark forms part of the alternative presentation in the application for permission to construct and operate an installation at Clab. The main technical difference between the planned encapsulation plant at Clab and an encapsulation plant at a final repository at Forsmark is how the fuel is managed and prepared before actual encapsulation. Fuel reception at the encapsulation plant in Forsmark would be dry, i.e. there would be no water-filled pools at the facility. Clab is used for verificatory fuel measurements, sorting and drying of the fuel before transport to Forsmark. This means that Clab will require a measure of rebuilding and supplementary equipment. In purely technical terms, the prospects for building an encapsulation plant sited at Forsmark are good. A description of the advantages and drawbacks of siting the encapsulation plant at Clab as opposed to any final repository at Forsmark is presented in a separate

75 FR 11575 - James A. Fitzpatrick Nuclear Power Plant Environmental Assessment and Finding of No Significant...

Science.gov (United States)

2010-03-11

... Power Plant Environmental Assessment and Finding of No Significant Impact The U.S. Nuclear Regulatory...), for the operation of the James A. FitzPatrick Nuclear Power Plant (JAFNPP) located in Oswego County... the Final Environmental Statement for the James A. FitzPatrick Nuclear Power Plant, Docket No. 50-333...

Exergy Analysis of Operating Lignite Fired Thermal Power Plant

Directory of Open Access Journals (Sweden)

K. Murugesan

2009-01-01

Full Text Available The energy assessment must be made through the energy quantity as well as the quality. But the usual energy analysisevaluates the energy generally on its quantity only. However, the exergy analysis assesses the energy on quantity as well asthe quality. The aim of the exergy analysis is to identify the magnitudes and the locations of real energy losses, in order toimprove the existing systems, processes or components. The present paper deals with an exergy analysis performed on anoperating 50MWe unit of lignite fired steam power plant at Thermal Power Station-I, Neyveli Lignite Corporation Limited,Neyveli, Tamil Nadu, India. The exergy losses occurred in the various subsystems of the plant and their components havebeen calculated using the mass, energy and exergy balance equations. The distribution of the exergy losses in several plantcomponents during the real time plant running conditions has been assessed to locate the process irreversibility. The Firstlaw efficiency (energy efficiency and the Second law efficiency (exergy efficiency of the plant have also been calculated.The comparison between the energy losses and the exergy losses of the individual components of the plant shows that themaximum energy losses of 39% occur in the condenser, whereas the maximum exergy losses of 42.73% occur in the combustor.The real losses of energy which has a scope for the improvement are given as maximum exergy losses that occurredin the combustor.

Decontamination of American plants engaged in nuclear weapon production

International Nuclear Information System (INIS)

Vladislavlev, V.V.

1992-01-01

The data on the Americal program dealing with sharp decreasing the levels of radioactive contamination and chemical pollution of soils and ground water in regions, where the plants for nuclear weapon manufacturing are located, are given

Orange County Littoral Cell CRSMP Wastewater and Power Plant Discharge Structures

Data.gov (United States)

California Natural Resource Agency — Graphical depiction of wastewater and power plant discharge pipelines/outlets locations in Southern California.The shapefile was collected by Everest International...

Orange County Littoral Cell CRSMP Wastewater and Power Plant Discharge Structures

Data.gov (United States)

California Department of Resources — Graphical depiction of wastewater and power plant discharge pipelines/outlets locations in Southern California.The shapefile was collected by Everest International...

Appraising manufacturing location

NARCIS (Netherlands)

Steenhuis, H.J.; de Bruijn, E.J.

2002-01-01

International location of manufacturing activities is an issue for managers of manufacturing companies as well as public policy makers. For managers, the issue is relevant because international locations offer opportunities for lowering costs due to productivity improvements. For governments the

Hydrographic parameters and distribution of dissolved Cu, Ni, Zn and nutrients near Jeddah desalination plant

Directory of Open Access Journals (Sweden)

Fallatah Mohammad M.

2018-04-01

Full Text Available The development of safe desalination plants with low environmental impact is as important an issue as the supply of drinking water. The desalination plant in Jeddah (Saudi Arabia, Red Sea coast produces freshwater from seawater by multi-stage flash distillation (MSFD and reverse osmosis (RO. The process produces brine as by-product, which is dumped into the sea. The aim of this study was to assess the impact of Jeddah desalination plant on the coastal water in the nearby of the plant. Total concentrations of dissolved Cu, Ni, Zn and nutrients in several locations around the plant were analyzed by cathodic stripping voltammetry. The average levels of dissolved Cu, Ni, and Zn on surface in the sampling locations were 15.02, 11.02, and 68.03 nM respectively, whereas the levels at the seafloor near the discharging point were much higher. Distribution of temperature, salinity, nutrients and dissolved oxygen were quite normal both on surface and in depth.

Ethnobotanical investigation of 'wild' food plants used by rice farmers in Kalasin, Northeast Thailand

NARCIS (Netherlands)

Cruz Garcia, G.S.; Price, L.L.

2011-01-01

Background Wild food plants are a critical component in the subsistence system of rice farmers in Northeast Thailand. One of the important characteristics of wild plant foods among farming households is that the main collection locations are increasingly from anthropogenic ecosystems such as

Characterization of deposits and their influence on corrosion in waste incineration plants in Denmark

DEFF Research Database (Denmark)

Montgomery, Melanie; Larsen, OH

2001-01-01

A program has been initiated in Denmark to investigate the aggressive environment in various waste incineration plants. The results described are the preliminary results from one waste incineration plant. Deposits and corrosion products have been removed from various locations in the boiler...

Comparative genomics of pseudomonas syringae pathovar tomato reveals novel chemotaxis pathways associated with motility and plant pathogenicity

Science.gov (United States)

The majority of bacterial foliar plant pathogens must invade the apoplast of host plants through points of ingress, such as stomata or wounds, replicate to high population density and cause disease. How pathogens navigate plant surfaces to locate invasion sites remains poorly understood. Many bacter...

Device for Automated Cutting and Transfer of Plant Shoots

Science.gov (United States)

Cipra, Raymond; Das, Hari; Ali, Khaled; Hong, Dennis

2003-01-01

A device that enables the automated cutting and transfer of plant shoots is undergoing development for use in the propagation of plants in a nursery or laboratory. At present, it is standard practice for a human technician to use a knife and forceps to cut, separate, and grasp a plant shoot. The great advantage offered by the present device is that its design and operation are simpler than would be those of a device based on the manual cutting/separation/grasping procedure. [The present device should not be confused with a prior device developed for partly the same purpose and described in Compliant Gripper for a Robotic Manipulator (NPO-21104), NASA Tech Briefs, Vol. 27, No. 3 (March 2003), page 59.]. The device (see figure) includes a circular tube sharpened at its open (lower) end and mounted on a robotic manipulator at its closed (upper) end. The robotic manipulator simply pushes the sharpened open end of the tube down onto a bed of plants and rotates a few degrees clockwise then counterclockwise about the vertical axis, causing the tube to cut a cylindrical plug of plant material. Exploiting the natural friction between the tube and plug, the tube retains the plug, without need for a gripping mechanism and control. The robotic manipulator then retracts the tube, translates it to a new location over a plant-growth tray, and inserts the tube part way into the growth medium at this location in the tray. A short burst of compressed air is admitted to the upper end of the tube to eject the plug of plant material and drive it into the growth medium. A prototype has been tested and verified to function substantially as intended. It is projected that in the fully developed robotic plant-propagation system, the robot control system would include a machine- vision subsystem that would automatically guide the robotic manipulator in choosing the positions from which to cut plugs of plant material. Planned further development efforts also include more testing and

Safeguards approaches for conversion and gas centrifuge enrichment plants

International Nuclear Information System (INIS)

Stanuch, C.; Whitaker, M.; Lockwood, D.; Boyer, B.

2013-01-01

This paper describes recent studies and investigations of new safeguards measures and inspection tools to strengthen international safeguards at GCEPs (Gas Centrifuge Enrichment Plants) and conversion plants. The IAEA has indicated that continuous, unattended process monitoring should play a central role in future safeguards approaches for conversion plants and GCEPs. Monitoring safeguards relevant information from accountancy scales, process load cells, and unit header pipes can make existing safeguards approaches more efficient by replacing repetitive, routine, labor-intensive inspection activities with automated systems. These systems can make the safeguards approach more effective by addressing more completely the safeguards objectives at these facilities. Automated collection and analysis of the data can further enable the IAEA to move towards a fully-information driven inspection regime with randomized (from the operator's perspective), short-notice inspections. The reduction in repetitive on-site inspection activities would also be beneficial to plant operators, but only if sensitive and proprietary information can be protected and the new systems prove to be reliable. New facilities that incorporate Safeguards by Design into the earliest design stages can facilitate the effective DIV (Design Information Verification) of the plant to allow the inspectors to analyze the capacity of the plant, to project maximum production from the plant, and to provide a focus on the areas in the plant where credible diversion scenarios could be attempted. Facilitating efficient nuclear material accountancy by simplifying process pipework and making flow measurement points more accessible can allow for easier estimation of plant holdup and a potential reduction in the number of person-days of inspection. Lastly, a universal monitoring standard that tracks the location, movement, and use of UF 6 cylinders may enhance the efficiency of operations at industry sites and would

Pipe support optimization in nuclear power plants

International Nuclear Information System (INIS)

Cleveland, A.B.; Kalyanam, N.

1984-01-01

A typical 1000 MWe nuclear power plant consists of 80,000 to 100,000 feet of piping which must be designed to withstand earthquake shock. For the required ground motion, seismic response spectra are developed for safety-related structures. These curves are used in the dynamic analysis of piping systems with pipe-stress analysis computer codes. To satisfy applicable Code requirements, the piping systems also require analysis for weight, thermal and possibly other lasting conditions. Bechtel Power Corporation has developed a design program called SLAM (Support Location Algorithm) for optimizing pipe support locations and types (rigid, spring, snubber, axial, lateral, etc.) while satisfying userspecified parameters such as locations, load combinations, stress and load allowables, pipe displacement and cost. This paper describes SLAM, its features, applications and benefits

Integrated plant safety assessment systematic evaluation program. R.E. Ginna Nuclear Power Plant, Rochester Gas and Electric Corporation, Docket No. 50-244

International Nuclear Information System (INIS)

1982-05-01

The Systematic Evaluation Program was initiated in February 1978 by the US Nuclear Regulatory Commission to review the designs of older operating nuclear reactor plants to reconfirm and document their safety. The review provides (1) an assessment of how these plants compare with current licensing safety requirements relating to selected issues, (2) a basis for deciding on how these differences should be resolved in an integrated plant review, and (3) a documented evaluation of plant safety. This report documents the review of the R.E. Ginna Nuclear Power Plant (located in Wayne County near Rochester, NY), one of ten plants reviewed under Phase II of this program, and indicates how 137 topics selected for review under Phase I of the program were addressed. Equipment and procedural changes have been identified as a result of the review. It is expected that this report will be one of the bases in considering the issuance of a full-term operating license in place of the existing provisional operating license

Impact of coal-fired thermal power plant emissions on surrounding vegetative environment: a case study

International Nuclear Information System (INIS)

Soni, D.K.; Senger, C.B.S.

1993-01-01

Vegetative system around the thermal power plants are exposed to perpetual emissions of particulates as well as gaseous pollutants in various forms and nature. These emissions evidently are reflected in plant responses. In order to assess the response of natural flora of this region, 2 plant species, that is Mangifera indica and Holarrhina artidysentrica and certain pollution sensitive parameter, such as leaf area, pH of wash water of foliage and sugar content of the leaves were identified for this study. It was observed that the pH of wash solution of leaves was close to neutral in upstream locations and in polluted zone pH was acidic. Leaf area was higher in least polluted zone and lower in more polluted locations. Dust deposition on leaves was observed be lower in upstream locations and higher in influenced areas. Sugar variations in leaves showed negative impact in affected areas. (author). 9 refs., 5 tabs

Green facility location

NARCIS (Netherlands)

Velázquez Martínez, J.C.; Fransoo, J.C.; Bouchery, Y.; Corbett, C.J.; Fransoo, J.C.; Tan, T.

2017-01-01

Transportation is one of the main contributing factors of global carbon emissions, and thus, when dealing with facility location models in a distribution context, transportation emissions may be substantially higher than the emissions due to production or storage. Because facility location models

Residential Location, Job Location, and Wages: Theory and Empirics

DEFF Research Database (Denmark)

Vejlin, Rune Majlund

-to-job transition without changing workplace location. However, workers making a job-to-job transition which makes the workplace location closer to the residence experiences a wage drop. Furthermore, low wage workers and workers with high transportation costs are more likely to make job-to-job transitions, but also......I develop a stylized partial on-the-job equilibrium search model which incorporate a spatial dimension. Workers reside on a circle and can move at a cost. Each point on the circle has a wage distribution. Implications about wages and job mobility are drawn from the model and tested on Danish...... matched employer-employee data. The model predictions hold true. I find that workers working farther away from their residence earn higher wages. When a worker is making a job-to-job transition where he changes workplace location he experiences a higher wage change than a worker making a job...

Hydrogeological and geophysics study of Conaprole industrial plant Tarariras Colonia province

International Nuclear Information System (INIS)

Cardozo, L.; Mari, C.; Massa, E.; Cicalese, H.

1985-01-01

To application of the National Cooperative of Producers of Milk (CONAPROLE), it proceeded to a hydro geologic and geophysical studies for the industrial plant of that Cooperative, located in Tarariras city (Colonia province) where it was determined the technical feasibility of exploration and exploitation of groundwater in one or more waterdrills to be executed in the proximities of the industrial plant .

Location-based Scheduling

DEFF Research Database (Denmark)

Andersson, Niclas; Christensen, Knud

on the market. However, CPM is primarily an activity based method that takes the activity as the unit of focus and there is criticism raised, specifically in the case of construction projects, on the method for deficient management of construction work and continuous flow of resources. To seek solutions...... to the identified limitations of the CPM method, an alternative planning and scheduling methodology that includes locations is tested. Location-based Scheduling (LBS) implies a shift in focus, from primarily the activities to the flow of work through the various locations of the project, i.e. the building. LBS uses...... the graphical presentation technique of Line-of-balance, which is adapted for planning and management of work-flows that facilitates resources to perform their work without interruptions caused by other resources working with other activities in the same location. As such, LBS and Lean Construction share...

Effect of wood fuels on power plant operability

International Nuclear Information System (INIS)

Orjala, M.; Ingalsuo, R.

2001-01-01

The objective of the research is to determine the critical properties of wood fuels on the basis of power plant operability, to determine the optimal conditions for reduction of harmful detriments, and to study how the storage and processing of wood fuels effect on the operability. Both the CFB and BFB technologies are studied. The project started in December 2000 and it will be ended by the end of 2002. Experts of the Fuels and Combustion research field of VTT Energy carry out the main parts of the research. Experts of the research field of Mineral Processing of VTT Chemical Technology, located in Outokumpu, and Kemian tutkimuspalvelut Oy/Oulu University, located in Outokumpu, participate in the analytics, and the research field of Materials and Manufacturing Technology of VTT Manufacturing Technology in Otaniemi participates in the research on material effects. System Technology Laboratory of Oulu University carries out the power plant automation and boiler control technology research under supervision of Professor Urpo Kortela. Co-operation with the materials research unit of EU's JRC, located in Petten, which started in the research 'Combustion of Forest Chips', will be continues in this research. Co-operation will be made with Swedish Vaermeforsk in the field of information exchange on experiences in utilisation of wood fuels in Swedish power plants and possibilities to join in the projects of Vaermeforsk in this research field. Following companies participate in the project: Etelae-Savon Energia Oy, Foster Wheeler Energia Oy, Kvaerner Pulping Oy, Simpele pasteboard factory of M-Real Oyj and Vaermeforsk AB (Sweden). (orig.)

The variability of interconnected wind plants

International Nuclear Information System (INIS)

Katzenstein, Warren; Fertig, Emily; Apt, Jay

2010-01-01

We present the first frequency-dependent analyses of the geographic smoothing of wind power's variability, analyzing the interconnected measured output of 20 wind plants in Texas. Reductions in variability occur at frequencies corresponding to times shorter than ∼24 h and are quantified by measuring the departure from a Kolmogorov spectrum. At a frequency of 2.8x10 -4 Hz (corresponding to 1 h), an 87% reduction of the variability of a single wind plant is obtained by interconnecting 4 wind plants. Interconnecting the remaining 16 wind plants produces only an additional 8% reduction. We use step change analyses and correlation coefficients to compare our results with previous studies, finding that wind power ramps up faster than it ramps down for each of the step change intervals analyzed and that correlation between the power output of wind plants 200 km away is half that of co-located wind plants. To examine variability at very low frequencies, we estimate yearly wind energy production in the Great Plains region of the United States from automated wind observations at airports covering 36 years. The estimated wind power has significant inter-annual variability and the severity of wind drought years is estimated to be about half that observed nationally for hydroelectric power.

Medicinal plant diversity of Sitamata wildlife sanctuary, Rajasthan, India.

Science.gov (United States)

Jain, Anita; Katewa, S S; Galav, P K; Sharma, Pallavi

2005-11-14

The present study has been carried out in Sitamata wildlife sanctuary of Chittorgarh and Udaipur district located in south-west region of Rajasthan. A field survey of the study area was carried out during 2002-2004 to document the medicinal utility of herbs occurring in this area. Two hundred fourty-three genera belonging to 76 families have been reported which are used by the tribals of about 50 villages around the sanctuary as means of primary health care to cure various ailments. The study revealed the new ethnobotanical uses of 24 plant species belonging to 20 genera. A list of plant species along with their local name, plant part/s used and mode of administration for effective control in different ailments of ethnomedicinal plants are given.

Saudi anti-human cancer plants database (SACPD): A collection of plants with anti-human cancer activities.

Science.gov (United States)

Al-Zahrani, Ateeq Ahmed

2018-01-30

Several anticancer drugs have been developed from natural products such as plants. Successful experiments in inhibiting the growth of human cancer cell lines using Saudi plants were published over the last three decades. Up to date, there is no Saudi anticancer plants database as a comprehensive source for the interesting data generated from these experiments. Therefore, there was a need for creating a database to collect, organize, search and retrieve such data. As a result, the current paper describes the generation of the Saudi anti-human cancer plants database (SACPD). The database contains most of the reported information about the naturally growing Saudi anticancer plants. SACPD comprises the scientific and local names of 91 plant species that grow naturally in Saudi Arabia. These species belong to 38 different taxonomic families. In Addition, 18 species that represent16 family of medicinal plants and are intensively sold in the local markets in Saudi Arabia were added to the database. The website provides interesting details, including plant part containing the anticancer bioactive compounds, plants locations and cancer/cell type against which they exhibit their anticancer activity. Our survey revealed that breast, liver and leukemia were the most studied cancer cell lines in Saudi Arabia with percentages of 27%, 19% and 15%, respectively. The current SACPD represents a nucleus around which more development efforts can expand to accommodate all future submissions about new Saudi plant species with anticancer activities. SACPD will provide an excellent starting point for researchers and pharmaceutical companies who are interested in developing new anticancer drugs. SACPD is available online at https://teeqrani1.wixsite.com/sapd.

Mass spectrometry approaches to study plant endomembrane trafficking

DEFF Research Database (Denmark)

Parsons, Harriet Tempé; Lilley, Kathryn S.

2018-01-01

. Trafficking of membrane proteins to their correct endomembrane location is especially important to enable them to carry out their function. Although a considerable amount of knowledge about membrane protein trafficking in plants has been delivered by years of dedicated research, there are still significant...... gaps in our understanding of this process. Further knowledge of endomembrane trafficking is dependent on thorough characterization of the subcellular components that constitute the endomembrane system. Such studies are challenging for a number of reasons including the complexity of the plant...

Gene Locater

DEFF Research Database (Denmark)

Anwar, Muhammad Zohaib; Sehar, Anoosha; Rehman, Inayat-Ur

2012-01-01

software's for calculating recombination frequency is mostly limited to the range and flexibility of this type of analysis. GENE LOCATER is a fully customizable program for calculating recombination frequency, written in JAVA. Through an easy-to-use interface, GENE LOCATOR allows users a high degree...... of flexibility in calculating genetic linkage and displaying linkage group. Among other features, this software enables user to identify linkage groups with output visualized graphically. The program calculates interference and coefficient of coincidence with elevated accuracy in sample datasets. AVAILABILITY...

Study of genetic behavior of some early maturing and high yielding mutant lines of soybean in different locations

International Nuclear Information System (INIS)

Mir Ali, N.; Moualla, M.

2007-01-01

this study aimed at checking the stability of some mutant lines from soybean varieties in different locations and to select the best performing lines in each location. These lines 15 were selected according to previous experiments as being early maturing and/or that yield higher than the control. The study lasted three years, the experiment plants were grown in 3 locations: Raqa, Idleb and Lattakia. The experiment was designed as RCBD with 3 replicates for each variety. Results showed significant difference between lines, Locations and year in both earliness and yield, A significant interaction was realized between (line X location) and (line X year) for earliness and yield. For earliness (line X year) was not significant. The reverse situation was realized for yield. Location X year of yield and earliness was significant. Earliness was correlated positively with all characters (except for 100-seed-weight). Yield was positively and significantly correlated with characters of all lines. Three lines with higher yield than the control (142.61%) and same maturity time were selected. (author)

Cooling water in the study of nuclear power plants sites

International Nuclear Information System (INIS)

Martinez, J.J.C.

1990-01-01

The location of an electric power plant has its limitations as regards the availability of apt sites. The radiosanitary risk, seismic risk and the overload capacity of the ground can be generically enumerated, being the cooling water availability for an electric power plant a basic requirement. Diverse cooling systems may be employed but the aim must always be that thermal contamination in the immediate environment be the least possible. (Author) [es

Countermeasures to earthquakes in nuclear plants

International Nuclear Information System (INIS)

Sato, Kazuhide

1979-01-01

The contribution of atomic energy to mankind is unmeasured, but the danger of radioactivity is a special thing. Therefore in the design of nuclear power plants, the safety has been regarded as important, and in Japan where earthquakes occur frequently, the countermeasures to earthquakes have been incorporated in the examination of safety naturally. The radioactive substances handled in nuclear power stations and spent fuel reprocessing plants are briefly explained. The occurrence of earthquakes cannot be predicted effectively, and the disaster due to earthquakes is apt to be remarkably large. In nuclear plants, the prevention of damage in the facilities and the maintenance of the functions are required at the time of earthquakes. Regarding the location of nuclear plants, the history of earthquakes, the possible magnitude of earthquakes, the properties of ground and the position of nuclear plants should be examined. After the place of installation has been decided, the earthquake used for design is selected, evaluating live faults and determining the standard earthquakes. As the fundamentals of aseismatic design, the classification according to importance, the earthquakes for design corresponding to the classes of importance, the combination of loads and allowable stress are explained. (Kako, I.)

Seismic safety of nuclear power plants