Chemical weathering outputs from the flood plain of the Ganga

Science.gov (United States)

Bickle, Michael J.; Chapman, Hazel J.; Tipper, Edward; Galy, Albert; De La Rocha, Christina L.; Ahmad, Talat

2018-03-01

Transport of sediment across riverine flood plains contributes a significant but poorly constrained fraction of the total chemical weathering fluxes from rapidly eroding mountain belts which has important implications for chemical fluxes to the oceans and the impact of orogens on long term climate. We report water and bedload chemical analyses from the Ganges flood-plain, a major transit reservoir of sediment from the Himalayan orogen. Our data comprise six major southern tributaries to the Ganga, 31 additional analyses of major rivers from the Himalayan front in Nepal, 79 samples of the Ganga collected close to the mouth below the Farakka barrage every two weeks over three years and 67 water and 8 bedload samples from tributaries confined to the Ganga flood plain. The flood plain tributaries are characterised by a shallow δ18O - δD array, compared to the meteoric water line, with a low δDexcess from evaporative loss from the flood plain which is mirrored in the higher δDexcess of the mountain rivers in Nepal. The stable-isotope data confirms that the waters in the flood plain tributaries are dominantly derived from flood plain rainfall and not by redistribution of waters from the mountains. The flood plain tributaries are chemically distinct from the major Himalayan rivers. They can be divided into two groups. Tributaries from a small area around the Kosi river have 87Sr/86Sr ratios >0.75 and molar Na/Ca ratios as high as 6. Tributaries from the rest of the flood plain have 87Sr/86Sr ratios ≤0.74 and most have Na/Ca ratios waters have lost up to 70% of their Ca (average ∼ 50%) to precipitation of secondary calcite which is abundant as a diagenetic cement in the flood plain sediments. 31% of the Sr, 8% of the Ca and 45% of the Mg are calculated to be derived from silicate minerals. Because of significant evaporative loss of water across the flood plain, and in the absence of hydrological data for flood plain tributaries, chemical weathering fluxes from the

Long-term Agroecosystem Research in the Northern Great Plains.

Science.gov (United States)

Schmer, M.; Sanderson, M.; Liebig, M. A.; Wienhold, B.; Awada, T.; Papiernik, S.; Osborne, S.; Kemp, W.; Okalebo, J. A.; Riedall, W.

2015-12-01

The Northern Great Plains is the bread basket of the United States, accounting for a substantial portion of U.S. agricultural production. This region faces critical challenges regarding balancing food needs, resource conservation (e.g Ogallala aquifer), environmental concerns, and rural economy development. Developing transformative, multifunctional systems will require equally imaginative and efficient tools to help farmers manage complex agroecosystems in a rapidly changing climate. The Northern Plains long-term agroecosystem research (LTAR) site at Mandan, ND and the Platte River High Plains LTAR (ARS/University of Nebraska-Lincoln) at Lincoln, NE in collaboration with USDA-ARS research units in Brookings, SD and Fargo, ND are collaborating to address the grand challenge of providing and sustaining multiple service provisions from Northern Great Plains agroecosystems. We propose to attain these goals through sustainable intensification based on the adoption of conservation agriculture principles including reduced soil disturbance, livestock integration, and greater complexity and diversity in the cropping system. Here, we summarize new concepts these locations have pioneered in dynamic cropping systems, resource use efficiency, and agricultural management technologies. As part of the LTAR network, we will conduct long-term cross-site research to design and assess new agricultural practices and systems aimed at improving our understanding of decision making processes and outcomes across an array of agricultural systems.

TLD array for precise dose measurements in stereotactic radiation techniques

International Nuclear Information System (INIS)

Ertl, A.; Kitz, K.; Griffitt, W.; Hartl, R.F.E.; Zehetmayer, M.

1996-01-01

We developed a new TLD array for precise dose measurement and verification of the spatial dose distribution in small radiation targets. It consists of a hemicylindrical, tissue-equivalent rod made of polystyrene with 17 parallel moulds for an exact positioning of each TLD. The spatial resolution of the TLD array was evaluated using the Leskell spherical phantom. Dose planning was performed with KULA 4.4 under stereotactic conditions on axial CT images. In the Leksell gamma unit the TLD array was irradiated with a maximal dose of 10 Gy with an unplugged 14 mm collimator. The doses delivered to the TLDs were rechecked by diode detector and film dosimetry and compared to the computer-generated dose profile. We found excellent agreement of our measured values, even at the critical penumbra decline. For the 14 mm and 18 mm collimator and for the 11 mm collimator combination we compared the measured and calculated data at full width at half maximum. This TLD array may be useful for phantom or tissue model studies on the spatial dose distribution in confined radiation targets as used in stereotactic radiotherapy. (author)

Developing a hybrid solar/wind powered irrigation system for crops in the Great Plains

Science.gov (United States)

Some small scale irrigation systems (powered by wind or solar do not require subsidies, but this paper discusses ways to achieve an economical renewable energy powered center pivot irrigation system for crops in the Great Plains. By adding a solar-photovoltaic (PV) array together with a wind...

Evidence brief – Plain packaging of tobacco products: measures to decrease smoking initiation and increase cessation

DEFF Research Database (Denmark)

Olsen, Céline E J L Brassart

2015-01-01

to women and young people. They also show that, when combined with large pictorial health warnings, plain-packaging measures increase awareness about the risks related to tobacco consumption, encouraging more people to quit and fewer to start. In that these measures merely regulate the use of logos...... or colours for public health purposes, they are in compliance with international trade and intellectual property law....

Plain film diagnostic of the acromio-clavicular dislocation

International Nuclear Information System (INIS)

Vogel, H.; Thomae, J.; Jungbluth, K.H.; Hamburg Univ.

1980-01-01

The distance between the clavicula and the acromion, between the clavicula and the processus coracoideus and the step height between the acromion and the clavicula arch were measured on roentgen films. Evaluated were plain films of the shoulder and of the chest. 64 patients with dislocation of the acromio-clavicular joint were compared to patients without shoulder lesion. The comparance of both groups showed that measures exceeding the upper limits of the group without lesions are highly suggestive for acromio-clavicular dislocation. If one defines an acromio-clavicular dislocation as proved when two of the measured three distances exceed the upper limit, then an acromio-clavicular dislocation could be seen in 36% of the analysed cases on plain films of the shoulder and in 56% on plain chest films. (orig.) [de

An optomechatronic curvature measurement array based on fiber Bragg gratings

International Nuclear Information System (INIS)

Chang, Hsing-Cheng; Lin, Shyan-Lung; Hung, San-Shan; Chang, I-Nan; Chen, Ya-Hui; Lin, Jung-Chih; Liu, Wen-Fung

2014-01-01

This study investigated an optomechatronic array-integrated signal processing module and a human–machine interface based on fiber Bragg grating sensing elements embedded in an elastic support matrix that involves using a self-located electromagnetic mechanism for curvature sensing and solid contour reconstruction. Using bilinear interpolation and average calculation methods, the smooth and accurate surface contours of convex and concave lenses are reconstructed in real-time. The elastic supporting optical sensing array is self-balanced to reduce operational errors. Compared with our previous single-head sensor, the sensitivity of the proposed array is improved by more than 15%. In the curvature range from −20.15 to +27.09 m −1 , the sensitivities are 3.53 pm m for the convex measurement and 2.15 pm m for the concave measurement with an error rate below 8.89%. The curvature resolutions are 0.283 and 0.465 m −1 for convex and concave lenses, respectively. This array could be applied in the curvature measurement of solar collectors to monitor energy conversion efficiency or could be used to monitor the wafer-level thin-film fabrication process. (paper)

MTF measurement and analysis of linear array HgCdTe infrared detectors

Science.gov (United States)

Zhang, Tong; Lin, Chun; Chen, Honglei; Sun, Changhong; Lin, Jiamu; Wang, Xi

2018-01-01

The slanted-edge technique is the main method for measurement detectors MTF, however this method is commonly used on planar array detectors. In this paper the authors present a modified slanted-edge method to measure the MTF of linear array HgCdTe detectors. Crosstalk is one of the major factors that degrade the MTF value of such an infrared detector. This paper presents an ion implantation guard-ring structure which was designed to effectively absorb photo-carriers that may laterally defuse between adjacent pixels thereby suppressing crosstalk. Measurement and analysis of the MTF of the linear array detectors with and without a guard-ring were carried out. The experimental results indicated that the ion implantation guard-ring structure effectively suppresses crosstalk and increases MTF value.

Plain packaging of cigarettes: do we have sufficient evidence?

Science.gov (United States)

Smith, Collin N; Kraemer, John D; Johnson, Andrea C; Mays, Darren

2015-01-01

Tobacco industry marketing is a primary factor influencing cigarette smoking behavior and the cigarette pack has become an important marketing vehicle for tobacco companies. Standardized “plain” cigarette packaging is advocated as a public health policy to prevent and reduce morbidity and mortality caused by smoking by reducing youth smoking initiation and promoting cessation among smokers. Plain packaging was implemented in Australia in December 2012, and several other countries are considering doing so, but each faces foreseeable legal resistance from opponents to such measures. Tobacco companies have challenged these public health policies, citing international trade agreements and intellectual property laws. Decision-making in these court cases will hinge in part on whether the evidence indicates the public health benefits of plain packaging outweigh any potential harm to tobacco manufacturers’ interests. We reviewed the available evidence in support of plain packaging, finding evidence from observational, experimental, and population-based studies. Results indicate that plain packaging can reduce positive perceptions of smoking and dissuade tobacco use. Governments deciding to implement plain cigarette packaging measures can rely on this evidence to help make a strong case that plain packaging plays an important role in the context of comprehensive smoking prevention efforts. PMID:25897269

The Effect of Fin Pitch on Fluid Elastic Instability of Tube Arrays Subjected to Cross Flow of Water

Science.gov (United States)

Desai, Sandeep Rangrao; Pavitran, Sampat

2018-02-01

Failure of tubes in shell and tube exchangers is attributed to flow induced vibrations of such tubes. There are different excitations mechanisms due to which flow induced vibration occurs and among such mechanisms, fluid elastic instability is the most prominent one as it causes the most violent vibrations and may lead to rapid tube failures within short time. Fluid elastic instability is the fluid-structure interaction phenomenon which occurs when energy input by the fluid force exceeds energy expended in damping. This point is referred as instability threshold and corresponding velocity is referred as critical velocity. Once flow velocity exceeds critical flow velocity, the vibration amplitude increases very rapidly with flow velocity. An experimental program is carried out to determine the critical velocity at instability for plain and finned tube arrays subjected to cross flow of water. The tube array geometry is parallel triangular with cantilever end condition and pitch ratios considered are 2.6 and 2.1. The objective of research is to determine the effect of increase in pitch ratio on instability threshold for plain tube arrays and to assess the effect of addition of fins as well as increase in fin density on instability threshold for finned tube arrays. Plain tube array with two different pitch ratios; 2.1 and 2.6 and finned tube arrays with same pitch ratio; 2.6 but with two different fin pitches; such as fine (10 fpi) and coarse (4 fpi) are considered for the experimentation. Connors' equation that relates critical velocity at instability to different parameters, on which instability depends, has been used as the basis for analysis and the concept of effective diameter is used for the present investigation. The modal parameters are first suitably modified using natural frequency reduction setup that is already designed and developed to reduce natural frequency and hence to achieve experimental simulation of fluid elastic instability within the limited

Fabrication of Faraday Cup Array for the Measurement of 2-Dimensional Proton Beam Profile

International Nuclear Information System (INIS)

Jung, Myunghwan; Kim, Bom Sok; Kim, Kyeryung

2014-01-01

It has an advantage of easy-to-use and possible to visually check, immediately; on the other hand, the measurement range is very limited. Another method is using the CCD camera-scintillator device such as p43 phosphor screen or chromox. A variety of faraday cup detectors have been recently introduced. The faraday cup is one of the powerful and popular tools for the measurement of beam current. By using several faraday cups in array geometry, it is possible to observe current distribution. In this study, we developed an external faraday cup array for the measure the beam current and profile at a KOMAC (Korea Multi-purpose Accelerator Complex) beam utilization facility. To measure the beam profile, before fabrication of faraday cup array, we use gafchromic film. By making the faraday cup array we were able to reduce the consumption of Gafchromic film and a more accurate diagnosis of the proton beam is possible. The use of faraday cup array, experiment using the proton beam is more reliable and confident

Directional spectrum of ocean waves from array measurements using phase/time/path difference methods

Digital Repository Service at National Institute of Oceanography (India)

Fernandes, A.A.; Sarma, Y.V.B.; Menon, H.B.

Wave direction has for the first time been consistently, accurately and unambiguously evaluated from array measurements using the phase/time/path difference (PTPD) methods of Esteva in case of polygonal arrays and Borgman in case of linear arrays...

LASE measurements of water vapor and aerosol profiles during the Plains Elevated Convection at Night (PECAN) field experiment

Science.gov (United States)

Nehrir, A. R.; Ferrare, R. A.; Kooi, S. A.; Butler, C. F.; Notari, A.; Hair, J. W.; Collins, J. E., Jr.; Ismail, S.

2015-12-01

The Lidar Atmospheric Sensing Experiment (LASE) system was deployed on the NASA DC-8 aircraft during the Plains Elevated Convection At Night (PECAN) field experiment, which was conducted during June-July 2015 over the central and southern plains. LASE is an active remote sensor that employs the differential absorption lidar (DIAL) technique to measure range resolved profiles of water vapor and aerosols above and below the aircraft. The DC-8 conducted nine local science flights from June 30- July 14 where LASE sampled water vapor and aerosol fields in support of the PECAN primary science objectives relating to better understanding nocturnal Mesoscale Convective Systems (MCSs), Convective Initiation (CI), the Low Level Jet (LLJ), bores, and to compare different airborne and ground based measurements. LASE observed large spatial and temporal variability in water vapor and aerosol distributions in advance of nocturnal MCSs, across bores resulting from MCS outflow boundaries, and across the LLJ associated with the development of MCSs and CI. An overview of the LASE data collected during the PECAN field experiment will be presented where emphasis will be placed on variability of water vapor profiles in the vicinity of severe storms and intense convection in the central and southern plains. Preliminary comparisons show good agreement between coincident LASE and radiosonde water vapor profiles. In addition, an advanced water vapor DIAL system being developed at NASA Langley will be discussed.

Ground level measurement of nuclei from coal development in the northern Great Plains: baseline measurements. Final report

Energy Technology Data Exchange (ETDEWEB)

Davis, B. L.; Johnson, L. R.; Sengupta, S.; Yue, P. C.

1978-11-01

The Institute of Atmospheric Sciences of the South Dakota School of Mines and Technology has completed 20 months of ambient air sampling at rural and remote sites in a five-state region of the northern Great Plains. Sampling was accomplished by use of a 27-ft motor home laboratory containing living accommodations for a field crew of two. The laboratory was outfitted with a number of instruments for measurement of pollutant parameters: cloud condensation nuclei, ice nuclei, Aitken nuclei, size distribution information for Aitken size particulate, sulfur dioxide, ozone, raindrop size distributions, and pH of precipitation. In addition, an instrumented meteorological tower provided wind speed, wind direction, ambient air temperature, and dew-point temperature. Instruments varied as to durability and success of operation, but better than 90% data retrieval was possible for the entire 20-month sampling study. Analyses of the large quantities of data obtained were not possible under the initial baseline measurement program, but examination of most parameters indicate that the air masses in the northern Great Plains are still relatively clean and are influenced primarily by local sources of contamination rather than large regional sources. Particulate concentrations in these remote areas are representative of mountain stations or clean rural conditions, and sulfur dioxide concentrations are at the threshold of detectability of the instrument. Precipitation is only very slightly acidic, and no significant quantity of amorphous particles (such as coal dust or combustion products) is found in the quantitative analyses of the high-volume filter collections. A summary of ''average'' conditions observed over the study area is tabulated.

Plain packaging of cigarettes: do we have sufficient evidence?

Directory of Open Access Journals (Sweden)

Smith CN

2015-04-01

Full Text Available Collin N Smith,1 John D Kraemer,2 Andrea C Johnson,1 Darren Mays1 1Department of Oncology, Georgetown University Medical Center, Lombardi Comprehensive Cancer Center, Washington, DC, USA; 2Department of Health Systems Administration, School of Nursing and Health Studies, Georgetown University, Washington, DC, USA Abstract: Tobacco industry marketing is a primary factor influencing cigarette smoking behavior and the cigarette pack has become an important marketing vehicle for tobacco companies. Standardized “plain” cigarette packaging is advocated as a public health policy to prevent and reduce morbidity and mortality caused by smoking by reducing youth smoking initiation and promoting cessation among smokers. Plain packaging was implemented in Australia in December 2012, and several other countries are considering doing so, but each faces foreseeable legal resistance from opponents to such measures. Tobacco companies have challenged these public health policies, citing international trade agreements and intellectual property laws. Decision-making in these court cases will hinge in part on whether the evidence indicates the public health benefits of plain packaging outweigh any potential harm to tobacco manufacturers’ interests. We reviewed the available evidence in support of plain packaging, finding evidence from observational, experimental, and population-based studies. Results indicate that plain packaging can reduce positive perceptions of smoking and dissuade tobacco use. Governments deciding to implement plain cigarette packaging measures can rely on this evidence to help make a strong case that plain packaging plays an important role in the context of comprehensive smoking prevention efforts. Keywords: cigarette smoking, tobacco, plain packaging, regulation, policy

Distributed 3D Source Localization from 2D DOA Measurements Using Multiple Linear Arrays

Directory of Open Access Journals (Sweden)

Antonio Canclini

2017-01-01

Full Text Available This manuscript addresses the problem of 3D source localization from direction of arrivals (DOAs in wireless acoustic sensor networks. In this context, multiple sensors measure the DOA of the source, and a central node combines the measurements to yield the source location estimate. Traditional approaches require 3D DOA measurements; that is, each sensor estimates the azimuth and elevation of the source by means of a microphone array, typically in a planar or spherical configuration. The proposed methodology aims at reducing the hardware and computational costs by combining measurements related to 2D DOAs estimated from linear arrays arbitrarily displaced in the 3D space. Each sensor measures the DOA in the plane containing the array and the source. Measurements are then translated into an equivalent planar geometry, in which a set of coplanar equivalent arrays observe the source preserving the original DOAs. This formulation is exploited to define a cost function, whose minimization leads to the source location estimation. An extensive simulation campaign validates the proposed approach and compares its accuracy with state-of-the-art methodologies.

Tietkens Plain karst - Maralinga

International Nuclear Information System (INIS)

James, J.M.

1988-09-01

The Tietkens Plain karst is located to the north of Maralinga village which is on the crest of the Ooldea Range on the north and east margin of the Nullarbor Plain in western South Australia. The geology of the carbonate rocks in the Maralinga area is summarised. On Tietkens Plain from 1955 to 1963 nuclear weapons tests dispersed radioactive materials over the Maralinga area. Six nuclear devices were detonated in the air and one was exploded a few metres below the surface. The effect such explosions have on the karst and the possible rate of recovery of its surface are discussed. This report is the record of a visit to the Maralinga area from the 15th -21st November 1986 which involved an inspection of the karst surface together with collection of water, soil and rock samples. Results of the measurements made in order to assess water quality and water contamination by radioactive nuclides are presented. The implications arising from the presence of radioactive materials on the surface and the possibility of their entering and contaminating the groundwater in the area are discussed in the context of the chemistry of uranium and plutonium. The potential for transmission of contaminants through groundwater conduits and aquifers in the dolomite is discussed. Evidence is produced to show that the caves of the Nullabor Plain are not contaminated at present and are unlikely to be so in the future. 21 refs., 2 figs. 3 tabs., ills

Exploration of deep S-wave velocity structure using microtremor array technique to estimate long-period ground motion

International Nuclear Information System (INIS)

Sato, Hiroaki; Higashi, Sadanori; Sato, Kiyotaka

2007-01-01

In this study, microtremor array measurements were conducted at 9 sites in the Niigata plain to explore deep S-wave velocity structures for estimation of long-period earthquake ground motion. The 1D S-wave velocity profiles in the Niigata plain are characterized by 5 layers with S-wave velocities of 0.4, 0.8, 1.5, 2.1 and 3.0 km/s, respectively. The depth to the basement layer is deeper in the Niigata port area located at the Japan sea side of the Niigata plain. In this area, the basement depth is about 4.8 km around the Seirou town and about 4.1 km around the Niigata city, respectively. These features about the basement depth in the Niigata plain are consistent with the previous surveys. In order to verify the profiles derived from microtremor array exploration, we estimate the group velocities of Love wave for four propagation paths of long-period earthquake ground motion during Niigata-ken tyuetsu earthquake by multiple filter technique, which were compared with the theoretical ones calculated from the derived profiles. As a result, it was confirmed that the group velocities from the derived profiles were in good agreement with the ones from long-period earthquake ground motion records during Niigata-ken tyuetsu earthquake. Furthermore, we applied the estimation method of design basis earthquake input for seismically isolated nuclear power facilities by using normal mode solution to estimate long-period earthquake ground motion during Niigata-ken tyuetsu earthquake. As a result, it was demonstrated that the applicability of the above method for the estimation of long-period earthquake ground motion were improved by using the derived 1D S-wave velocity profile. (author)

Interferometry with flexible point source array for measuring complex freeform surface and its design algorithm

Science.gov (United States)

Li, Jia; Shen, Hua; Zhu, Rihong; Gao, Jinming; Sun, Yue; Wang, Jinsong; Li, Bo

2018-06-01

The precision of the measurements of aspheric and freeform surfaces remains the primary factor restrict their manufacture and application. One effective means of measuring such surfaces involves using reference or probe beams with angle modulation, such as tilted-wave-interferometer (TWI). It is necessary to improve the measurement efficiency by obtaining the optimum point source array for different pieces before TWI measurements. For purpose of forming a point source array based on the gradients of different surfaces under test, we established a mathematical model describing the relationship between the point source array and the test surface. However, the optimal point sources are irregularly distributed. In order to achieve a flexible point source array according to the gradient of test surface, a novel interference setup using fiber array is proposed in which every point source can be independently controlled on and off. Simulations and the actual measurement examples of two different surfaces are given in this paper to verify the mathematical model. Finally, we performed an experiment of testing an off-axis ellipsoidal surface that proved the validity of the proposed interference system.

Perceptions of branded and plain cigarette packaging among Mexican youth.

Science.gov (United States)

Mutti, Seema; Hammond, David; Reid, Jessica L; White, Christine M; Thrasher, James F

2017-08-01

Plain cigarette packaging, which seeks to remove all brand imagery and standardize the shape and size of cigarette packs, represents a novel policy measure to reduce the appeal of cigarettes. Plain packaging has been studied primarily in high-income countries like Australia and the UK. It is unknown whether the effects of plain packaging may differ in low-and-middle income countries with a shorter history of tobacco regulation, such as Mexico. An experimental study was conducted in Mexico City to examine perceptions of branded and plain cigarette packaging among smoking and non-smoking Mexican adolescents (n = 359). Respondents were randomly assigned to a branded or plain pack condition and rated 12 cigarette packages for appeal, taste, harm to health and smoker-image traits. As a behavioral measure of appeal, respondents were offered (although not given) four cigarette packs (either branded or plain) and asked to select one to keep. The findings indicated that branded packs were perceived to be more appealing (β = 3.40, p packaging may reduce brand appeal among Mexican youth, consistent with findings in high-income countries. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Simulating Shallow Soil Response Using Wave Propagation Numerical Modelling in the Western Plain of Taiwan

Directory of Open Access Journals (Sweden)

Chun-Te Chen

2016-06-01

Full Text Available This study used the results from 45 microtremor array measurements to construct a shallow shear wave velocity structure in the western plain of Taiwan. We constructed a complete 3D velocity model based on shallow and tomography models for our numerical simulation. There are three major subsurfaces, engineering bedrock (VS = 600 m s-1, Pliocene formation and Miocene formation, constituted in the shallow model. The constant velocity is given in each subsurface. We employed a 3D-FD (finite-differences method to simulate seismic wave propagation in the western plain. The aim of this study was to perform a quantitative comparison of site amplifications and durations obtained from empirical data and numerical modelling in order to obtain the shallow substructure soil response. Modelling clearly revealed that the shallow substructure plays an important role in strong ground motion prediction using 3D simulation. The results show significant improvements in effective shaking duration and the peak ground velocity (PGV distribution in terms of the accuracy achieved by our developed model. We recommend a high-resolution shallow substructure as an essential component in future seismic hazard analyses.

Radiographical measurements for distal intra-articular fractures of the radius using plain radiographs and cone beam computed tomography images

Energy Technology Data Exchange (ETDEWEB)

Suojaervi, Nora; Lindfors, N. [Helsinki University Central Hospital, Department of Hand Surgery, Helsinki (Finland); Sillat, T.; Koskinen, S.K. [HUS Helsinki Medical Imaging Center, Helsinki University Central Hospital, Department of Radiology, Helsinki (Finland)

2015-12-15

Operative treatment of an intra-articular distal radius fracture is one of the most common procedures in orthopedic and hand surgery. The intra- and interobserver agreement of common radiographical measurements of these fractures using cone beam computed tomography (CBCT) and plain radiographs were evaluated. Thirty-seven patients undergoing open reduction and volar fixation for a distal radius fracture were studied. Two radiologists analyzed the preoperative radiographs and CBCT images. Agreement of the measurements was subjected to intra-class correlation coefficient and the Bland-Altman analyses. Plain radiographs provided a slightly poorer level of agreement. For fracture diastasis, excellent intraobserver agreement was achieved for radiographs and good or excellent agreement for CBCT, compared to poor interobserver agreement (ICC 0.334) for radiographs and good interobserver agreement (ICC 0.621) for CBCT images. The Bland-Altman analyses indicated a small mean difference between the measurements but rather large variation using both imaging methods, especially in angular measurements. For most of the measurements, radiographs do well, and may be used in clinical practice. Two different measurements by the same reader or by two different readers can lead to different decisions, and therefore a standardization of the measurements is imperative. More detailed analysis of articular surface needs cross-sectional imaging modalities. (orig.)

Radiographical measurements for distal intra-articular fractures of the radius using plain radiographs and cone beam computed tomography images.

Science.gov (United States)

Suojärvi, Nora; Sillat, T; Lindfors, N; Koskinen, S K

2015-12-01

Operative treatment of an intra-articular distal radius fracture is one of the most common procedures in orthopedic and hand surgery. The intra- and interobserver agreement of common radiographical measurements of these fractures using cone beam computed tomography (CBCT) and plain radiographs were evaluated. Thirty-seven patients undergoing open reduction and volar fixation for a distal radius fracture were studied. Two radiologists analyzed the preoperative radiographs and CBCT images. Agreement of the measurements was subjected to intra-class correlation coefficient and the Bland-Altman analyses. Plain radiographs provided a slightly poorer level of agreement. For fracture diastasis, excellent intraobserver agreement was achieved for radiographs and good or excellent agreement for CBCT, compared to poor interobserver agreement (ICC 0.334) for radiographs and good interobserver agreement (ICC 0.621) for CBCT images. The Bland-Altman analyses indicated a small mean difference between the measurements but rather large variation using both imaging methods, especially in angular measurements. For most of the measurements, radiographs do well, and may be used in clinical practice. Two different measurements by the same reader or by two different readers can lead to different decisions, and therefore a standardization of the measurements is imperative. More detailed analysis of articular surface needs cross-sectional imaging modalities.

Diagnosis of lumbar central spinal stenosis by plain radiography

International Nuclear Information System (INIS)

Ilkko, E.

1989-01-01

The usefulness of plain radiography in the diagnosis of lumbar central spinal stenosis was studied in 116 patients using computed tomography (CT) as a reference. The most significant signs found in central spinal stenosis were short pedicles, high narrow intervertebral foramina, small interlaminar windows and deep posterior concavity of the vertebral bodies. The sensitivity of plain radiography in the diagnosis of central spinal stenosis as compared to CT was 66%, the specificity was 93% and the accuracy was 86%. The midsagittal and interpedicular diameters were measured from plain radiograms and were compared with corresponding CT diameters. In approximately half of the cases, the sagittal diameters were compatible. The maximum error was 6 mm. On average, the interpedicular distances were measured as too wide. The reliability of CT measurements were established by taking the measurements from the vertebral column of a moose calf, and then comparing these to the real measurements obtained with a calibrated ruler. The maximal differences were 2 mm. (author). 24 refs.; 8 figs.; 3 tabs

Study on ecological regulation of coastal plain sluice

Science.gov (United States)

Yu, Wengong; Geng, Bing; Yu, Huanfei; Yu, Hongbo

2018-02-01

Coastal plains are densely populated and economically developed, therefore their importance is self-evident. However, there are some problems related with water in coastal plains, such as low flood control capacity and severe water pollution. Due to complicated river network hydrodynamic force, changeable flow direction and uncertain flood concentration and propagation mechanism, it is rather difficult to use sluice scheduling to realize flood control and tackle water pollution. On the base of the measured hydrological data during once-in-a-century Fitow typhoon in 2013 in Yuyao city, by typical analysis, theoretical analysis and process simulation, some key technologies were researched systematically including plain river network sluice ecological scheduling, “one tide” flood control and drainage scheduling and ecological running water scheduling. In the end, single factor health diagnostic evaluation, unit hydrograph of plain water level and evening tide scheduling were put forward.

SKA aperture array verification system: electromagnetic modeling and beam pattern measurements using a micro UAV

Science.gov (United States)

de Lera Acedo, E.; Bolli, P.; Paonessa, F.; Virone, G.; Colin-Beltran, E.; Razavi-Ghods, N.; Aicardi, I.; Lingua, A.; Maschio, P.; Monari, J.; Naldi, G.; Piras, M.; Pupillo, G.

2018-03-01

In this paper we present the electromagnetic modeling and beam pattern measurements of a 16-elements ultra wideband sparse random test array for the low frequency instrument of the Square Kilometer Array telescope. We discuss the importance of a small array test platform for the development of technologies and techniques towards the final telescope, highlighting the most relevant aspects of its design. We also describe the electromagnetic simulations and modeling work as well as the embedded-element and array pattern measurements using an Unmanned Aerial Vehicle system. The latter are helpful both for the validation of the models and the design as well as for the future instrumental calibration of the telescope thanks to the stable, accurate and strong radio frequency signal transmitted by the UAV. At this stage of the design, these measurements have shown a general agreement between experimental results and numerical data and have revealed the localized effect of un-calibrated cable lengths in the inner side-lobes of the array pattern.

Perfect additivity of microinterface arrays for liquid-liquid measurements: Application to cadmium ions quantification

International Nuclear Information System (INIS)

Mastouri, A.; Peulon, S.; Farcage, D.; Bellakhal, N.; Chaussé, A.

2014-01-01

Graphical abstract: - Highlights: • Confirmation of the perfect additivity of micropores independently of the geometry of arrays. • Study of assisted transfer of cadmium ions by 8-HQ at water/1,2-DCE. • Validation by cyclic and square wave voltammetry measurements for high and low concentrations. • Quantification of Cd(II) ions until 11 ppb in very simple conditions. • Highlighting of the very interesting use of arrays in a classical liquid-liquid microinterface device. - Abstract: For the first time, experimental measurements confirm the real additivity of the currents with micropore arrays, independently of the geometry (square, circular or in crosswise), from one single micropore until 256 micropores, in the case of the assisted transfer of cadmium ions by 8-hydroxyquinolinol (8-HQ). This result was obtained for measurements made by cyclic voltammetry at high concentration of cadmium ions (10 −4 M). At lower concentrations (until 10 −6 M), measurements performed by square wave voltammetry confirm also this additivity until 64 micropores. A calibration curve performed with a 64 micropores array allows us, in very simple conditions, the quantification of cadmium ions until 11 ppb (100 nM), which is lower than to the imposed limit for this specie in various fields, and in industrial effluents, in particular. The gain of sensitivity is close to 170 compared to measurements performed with one single micropore, illustrating the real interest of these arrays

In situ measurement of some gamma-emitting radionuclides in plant communities of the South Carolina coastal plain

International Nuclear Information System (INIS)

Ragsdale, H.L.; Tanner, B.K.; Coleman, R.N.; Palms, J.M.; Wood, R.E.

1978-01-01

In situ and laboratory gamma-ray spectroscopy measurements were taken in nine scrub oak forests and nine old fields to determine the applicability of in situ analysis in the coastal plain. Data collected at each of the 18 sites included a 2-hr count, soil density and moisture estimates, and vegetation measurements. Samples returned to the laboratory for radiometric analysis included litter and herbaceous vegetation and soil cores. Analysis of the gamma-emitter detection frequencies, concentrations, and burdens showed good to excellent agreement between laboratory and in situ methods. Generally, forests were determined to be superior in situ sampling systems. Laboratory analysis of collected samples may be a superior technique for gamma emitters with low energies, low concentrations, or nonuniform distributions in the soil. Three potential uses of in situ Ge(Li) spectrometers were identified and discussed in terms of their limits and of the replicate ecosystems appropriate for in situ analyses. Although the variety and the biogeochemical cycling regimes of southeastern coastal plain ecosystems complicate in situ analyses, it was concluded that comparable and probably accurate results can be achieved using in situ technology

Dual polarized receiving steering antenna array for measurement of ultrawideband pulse polarization structure

Energy Technology Data Exchange (ETDEWEB)

Balzovsky, E. V.; Buyanov, Yu. I.; Koshelev, V. I., E-mail: koshelev@lhfe.hcei.tsc.ru; Nekrasov, E. S. [Institute of High Current Electronics SB RAS, IHCE SB RAS, Tomsk 634055 (Russian Federation)

2016-03-15

To measure simultaneously two orthogonal components of the electromagnetic field of nano- and subnano-second duration, an antenna array has been developed. The antenna elements of the array are the crossed dipoles of dimension 5 × 5 cm. The arms of the dipoles are connected to the active four-pole devices to compensate the frequency response variations of a short dipole in the frequency band ranging from 0.4 to 4 GHz. The dipoles have superimposed phase centers allowing measuring the polarization structure of the field in different directions. The developed antenna array is the linear one containing four elements. The pattern maximum position is controlled by means of the switched ultrawideband true time delay lines. Discrete steering in seven directions in the range from −40° to +40° has been realized. The error at setting the pattern maximum position is less than 4°. The isolation of the polarization exceeds 29 dB in the direction orthogonal to the array axis and in the whole steering range it exceeds 23 dB. Measurement results of the polarization structure of radiated and scattered pulses with different polarization are presented as well.

Near-surface current meter array measurements of internal gravity waves

Energy Technology Data Exchange (ETDEWEB)

Jones, H.B.E. [Lawrence Livermore National Lab., CA (United States)

1994-11-15

We have developed various processing algorithms used to estimate the wave forms produced by hydrodynamic Internal Waves. Furthermore, the estimated Internal Waves are used to calculate the Modulation Transfer Function (MTF) which relates the current and strain rate subsurface fields to surface scattering phenomenon imaged by radar. Following a brief discussion of LLNL`s measurement platform (a 10 sensor current meter array) we described the generation of representative current and strain rate space-time images from measured or simulated data. Then, we present how our simulation capability highlighted limitations in estimating strain rate. These limitations spurred the application of beamforming techniques to enhance our estimates, albeit at the expense of collapsing our space-time images to 1-D estimates. Finally, we discuss progress with regard to processing the current meter array data captured during the recent Loch Linnhe field trials.

Measuring In-Home Walking Speed using Wall-Mounted RF Transceiver Arrays

Science.gov (United States)

Jacobs, Peter G.; Wan, Eric A.; Schafermeer, Erich; Adenwala, Fatema; Paul, Anindya S.; Preiser, Nick; Kaye, Jeffrey

2014-01-01

In this paper we present a new method for passively measuring walking speed using a small array of radio transceivers positioned on the walls of a hallway within a home. As a person walks between a radio transmitter and a receiver, the received signal strength (RSS) detected by the receiver changes in a repeatable pattern that may be used to estimate walking speed without the need for the person to wear any monitoring device. The transceivers are arranged as an array of 4 with a known distance between the array elements. Walking past the first pair of transceivers will cause a peak followed by a second peak when the person passes the second pair of transceivers. The time difference between these peaks is used to estimate walking speed directly. We further show that it is possible to estimate the walking speed by correlating the shape of the signal using a single pair of transceivers positioned across from each other in a hallway or doorframe. RMSE performance was less than 15 cm/s using a 2-element array, and less than 8 cm/s using a 4-element array relative to a gait mat used for ground truth. PMID:25570108

A decade of investigations on groundwater arsenic contamination in Middle Ganga Plain, India.

Science.gov (United States)

Saha, Dipankar; Sahu, Sudarsan

2016-04-01

Groundwater arsenic (As) load in excess of drinking limit (50 µg L(-1)) in the Gangetic Plains was first detected in 2002. Though the menace was known since about two decades from the downstream part of the plains in the Bengal Basin, comprising of Lower Ganga Plain and deltaic plains of Ganga-Brahmaputra-Meghna River system, little thought was given to its possible threat in the upstream parts in the Gangetic Plains beyond Garo-Rajmahal Hills. The contamination in Bengal Basin has become one of the extensively studied issues in the world and regarded as the severest case of health hazard in the history of mankind. The researches and investigations in the Gangetic Plains during the last decade (2003-2013) revealed that the eastern half of the plains, also referred as Middle Ganga Plain (MGP), is particularly affected by contamination, jeopardising the shallow aquifer-based drinking water supply. The present paper reviews researches and investigations carried out so far in MGP by various research institutes and government departments on wide array of issues of groundwater As such as its spatio-temporal variation, mobilisation paths, water level behaviour and flow regime, configuration of contaminated and safe aquifers and their recharge mechanism. Elevated conc. of groundwater As has been observed in grey and dark grey sediments of Holocene age (Newer Alluvium) deposited in a fluvio-lacustrine environment in the floodplain of the Ganga and most of its northern tributaries from Himalayas. Older Alluvium, comprising Pleistocene brownish yellow sediment, extending as deeper aquifers in Newer Alluvium areas, is low in groundwater As. Similarities and differences on issues between the MGP and the Bengal Basin have been discussed. The researches point towards the mobilisation process as reductive dissolution of iron hydroxide coating, rich in adsorbed As, mediated by microbial processes. The area is marked with shallow water level (<8.0 m below ground) with ample

Measurement of horizontal air showers with the Auger Engineering Radio Array

Science.gov (United States)

Kambeitz, Olga

2017-03-01

The Auger Engineering Radio Array (AERA), at the Pierre Auger Observatory in Argentina, measures the radio emission of extensive air showers in the 30-80 MHz frequency range. AERA consists of more than 150 antenna stations distributed over 17 km2. Together with the Auger surface detector, the fluorescence detector and the underground muon detector (AMIGA), AERA is able to measure cosmic rays with energies above 1017 eV in a hybrid detection mode. AERA is optimized for the detection of air showers up to 60° zenith angle, however, using the reconstruction of horizontal air showers with the Auger surface array, very inclined showers can also be measured. In this contribution an analysis of the AERA data in the zenith angle range from 62° to 80° will be presented. CoREAS simulations predict radio emission footprints of several km2 for horizontal air showers, which are now confirmed by AERA measurements. This can lead to radio-based composition measurements and energy determination of horizontal showers in the future and the radio detection of neutrino induced showers is possible.

Comparison of pH Data Measured with a pH Sensor Array Using Different Data Fusion Methods

OpenAIRE

Yi-Hung Liao; Jung-Chuan Chou

2012-01-01

This paper introduces different data fusion methods which are used for an electrochemical measurement using a sensor array. In this study, we used ruthenium dioxide sensing membrane pH electrodes to form a sensor array. The sensor array was used for detecting the pH values of grape wine, generic cola drink and bottled base water. The measured pH data were used for data fusion methods to increase the reliability of the measured results, and we also compared the fusion results with other differ...

Comparison of pH Data Measured with a pH Sensor Array Using Different Data Fusion Methods

Directory of Open Access Journals (Sweden)

Yi-Hung Liao

2012-09-01

Full Text Available This paper introduces different data fusion methods which are used for an electrochemical measurement using a sensor array. In this study, we used ruthenium dioxide sensing membrane pH electrodes to form a sensor array. The sensor array was used for detecting the pH values of grape wine, generic cola drink and bottled base water. The measured pH data were used for data fusion methods to increase the reliability of the measured results, and we also compared the fusion results with other different data fusion methods.

THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. I. BEAM PATTERN MEASUREMENTS AND SCIENCE IMPLICATIONS

International Nuclear Information System (INIS)

Neben, Abraham R.; Hewitt, Jacqueline N.; Ewall-Wice, Aaron; Bradley, Richard F.; DeBoer, David R.; Parsons, Aaron R.; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S.; Aguirre, James E.; Kohn, Saul A.; Thyagarajan, Nithyanandan; Bowman, Judd; Jacobs, Daniel C.; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia J.

2016-01-01

The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21 cm fluctuations from neutral hydrogen from the epoch of reionization (EOR). Drawing on lessons from the Murchison Widefield Array and the Precision Array for Probing the EOR, HERA is a hexagonal array of large (14 m diameter) dishes with suspended dipole feeds. The dish not only determines overall sensitivity, but also affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. In this paper, we focus on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay and thus apparent source frequency structure. We measure the angular response at 137 MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93 m 2 in the optimal dish/feed configuration, implying that HERA-320 should detect the EOR power spectrum at z ∼ 9 with a signal-to-noise ratio of 12.7 using a foreground avoidance approach with a single season of observations and 74.3 using a foreground subtraction approach. Finally, we study the impact of these beam measurements on the distribution of foregrounds in Fourier space.

THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. I. BEAM PATTERN MEASUREMENTS AND SCIENCE IMPLICATIONS

Energy Technology Data Exchange (ETDEWEB)

Neben, Abraham R.; Hewitt, Jacqueline N.; Ewall-Wice, Aaron [MIT Kavli Institute, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bradley, Richard F. [Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA 22904 (United States); DeBoer, David R.; Parsons, Aaron R.; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S. [Department of Astronomy, University of California, Berkeley, CA (United States); Aguirre, James E.; Kohn, Saul A. [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, PA (United States); Thyagarajan, Nithyanandan; Bowman, Judd; Jacobs, Daniel C. [Arizona State University, School of Earth and Space Exploration, Tempe, AZ 85287 (United States); Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia J. [National Radio Astronomy Observatory, Charlottesville, VA (United States); and others

2016-08-01

The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21 cm fluctuations from neutral hydrogen from the epoch of reionization (EOR). Drawing on lessons from the Murchison Widefield Array and the Precision Array for Probing the EOR, HERA is a hexagonal array of large (14 m diameter) dishes with suspended dipole feeds. The dish not only determines overall sensitivity, but also affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. In this paper, we focus on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay and thus apparent source frequency structure. We measure the angular response at 137 MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93 m{sup 2} in the optimal dish/feed configuration, implying that HERA-320 should detect the EOR power spectrum at z ∼ 9 with a signal-to-noise ratio of 12.7 using a foreground avoidance approach with a single season of observations and 74.3 using a foreground subtraction approach. Finally, we study the impact of these beam measurements on the distribution of foregrounds in Fourier space.

Plain formation on Mercury: tectonic implications

International Nuclear Information System (INIS)

Thomas, P.

1980-01-01

Four major plain units, plus intermediates, are distinguished on Mercury. The chronologic relationships between these plains indicate that plains formation was a permanent process on Mercury. Their location and morphology seem to indicate a possible volcanic origin for these plains. The relationships between tectonism and volcanism seems to indicate the global contraction is not the only tectonic process on Mercury. (Auth.)

Flatness of two-dimensional beam profile measured with an ionization chamber array

International Nuclear Information System (INIS)

Stefanovski, Z.

2006-01-01

Open beam profiles are basic dosimetric characteristics for the formation of the dose calculation algorithms parameters and for determination of beam quality. One characteristic of the beam profiles as a measure for the beam quality is the field flatness defined as ratio of the difference of maximum and minimum dose in central 80% of the field to the sum of these doses in the part of the field. The measurements, instead with an ordinary ionization chamber, were performed with a chamber array in two depths (1.6 cm and 10 cm) in water phantom. Nominal photon beam energy was 6 MV and field size was 25 cm x 25 cm on the water surface. Field flatness was in the range of 1-2 % which is in accordance with the data acquired during the acceptance testing and commissioning of the accelerators. with the array chamber the beam profiles can be performed quickly and preciously. These features recommend a chamber array as an excellent tool for periodic quality control of beam profiles. (Author)

Second chance for the plains bison

Science.gov (United States)

Freese, Curtis H.; Aune, K.; Boyd, D.; Derr, James N.; Forrest, Steven C.; Gates, C. Cormack; Gogan, Peter J.; Grassel, Shaun M.; Halbert, Natalie D.; Kunkel, Kyran; Redford, Kent

2007-01-01

Before European settlement the plains bison (Bison bison bison) numbered in the tens of millions across most of the temperate region of North America. Within the span of a few decades during the mid- to late-1800s its numbers were reduced by hunting and other factors to a few hundred. The plight of the plains bison led to one of the first major movements in North America to save an endangered species. A few individuals and the American Bison Society rescued the remaining animals. Attempts to hybridize cattle and bison when bison numbers were low resulted in extensive cattle gene introgression in bison. Today, though approximately 500,000 plains bison exist in North America, few are free of cattle gene introgression, 96% are subject to anthropogenic selection for commodity production, and only 4% are in herds managed primarily for conservation purposes. Small herd size, artificial selection, cattle-gene introgression, and other factors threaten the diversity and integrity of the bison genome. In addition, the bison is for all practical purposes ecologically extinct across its former range, with multiple consequences for grassland biodiversity. Urgent measures are needed to conserve the wild bison genome and to restore the ecological role of bison in grassland ecosystems. Socioeconomic trends in the Great Plains, combined with new information about bison conservation needs and new conservation initiatives by both the public and public sectors, have set the stage for significant progress in bison conservation over the next few years.

Assessment of Measurement Distortions in GNSS Antenna Array Space-Time Processing

Directory of Open Access Journals (Sweden)

Thyagaraja Marathe

2016-01-01

Full Text Available Antenna array processing techniques are studied in GNSS as effective tools to mitigate interference in spatial and spatiotemporal domains. However, without specific considerations, the array processing results in biases and distortions in the cross-ambiguity function (CAF of the ranging codes. In space-time processing (STP the CAF misshaping can happen due to the combined effect of space-time processing and the unintentional signal attenuation by filtering. This paper focuses on characterizing these degradations for different controlled signal scenarios and for live data from an antenna array. The antenna array simulation method introduced in this paper enables one to perform accurate analyses in the field of STP. The effects of relative placement of the interference source with respect to the desired signal direction are shown using overall measurement errors and profile of the signal strength. Analyses of contributions from each source of distortion are conducted individually and collectively. Effects of distortions on GNSS pseudorange errors and position errors are compared for blind, semi-distortionless, and distortionless beamforming methods. The results from characterization can be useful for designing low distortion filters that are especially important for high accuracy GNSS applications in challenging environments.

Numerical Simulations and Experimental Measurements of Scale-Model Horizontal Axis Hydrokinetic Turbines (HAHT) Arrays

Science.gov (United States)

Javaherchi, Teymour; Stelzenmuller, Nick; Seydel, Joseph; Aliseda, Alberto

2014-11-01

The performance, turbulent wake evolution and interaction of multiple Horizontal Axis Hydrokinetic Turbines (HAHT) is analyzed in a 45:1 scale model setup. We combine experimental measurements with different RANS-based computational simulations that model the turbines with sliding-mesh, rotating reference frame and blame element theory strategies. The influence of array spacing and Tip Speed Ratio on performance and wake velocity structure is investigated in three different array configurations: Two coaxial turbines at different downstream spacing (5d to 14d), Three coaxial turbines with 5d and 7d downstream spacing, and Three turbines with lateral offset (0.5d) and downstream spacing (5d & 7d). Comparison with experimental measurements provides insights into the dynamics of HAHT arrays, and by extension to closely packed HAWT arrays. The experimental validation process also highlights the influence of the closure model used (k- ω SST and k- ɛ) and the flow Reynolds number (Re=40,000 to 100,000) on the computational predictions of devices' performance and characteristics of the flow field inside the above-mentioned arrays, establishing the strengths and limitations of existing numerical models for use in industrially-relevant settings (computational cost and time). Supported by DOE through the National Northwest Marine Renewable Energy Center (NNMREC).

Anterior atlantodental and posterior atlantodental intervals on plain radiography, multidetector CT, and MRI

Energy Technology Data Exchange (ETDEWEB)

Cha, Seung Woo; Ryu, Jeong Ah; Park, Dong Woo [Dept. of Radiology, Hanyang University Guri Hospital, Hanyang University College of Medicine, Guri (Korea, Republic of); Yoon, Ki Bo; Lee, Seung Hun; Joo, Kyung Bin [Dept. of Radiology, Hanyang University Seoul Hospital, Hanyang University College of Medicine, Seoul(Korea, Republic of)

2015-01-15

To determine the normal values of the anterior atlantodental interval (AADI) and posterior atlantodental interval (PADI) on plain radiography, multidetector CT (MDCT) and MRI, as well as the dural sac width and spinal cord diameter at the atlantoaxial joint level on MRI. In total, 60 subjects underwent plain radiography, MRI and MDCT. We obtained values for AADI and PADI on plain radiography, MDCT, and MRI, and for dural sac width and spinal cord diameter on MRI. Two radiologists independently measured each value and a consensus was reached. The average AADI was 1.5 +/- 0.5 mm on plain radiography, 1.4 +/- 0.3 mm on MDCT, and 1.6 +/- 0.5 mm on MRI. The average PADI was 20.6 +/- 2.4 mm on plain radiography, 18.0 +/- 2.1 mm on MDCT, and 17.7 +/- 1.9 mm on MRI. The dural sac width was 13.7 +/- 1.8 mm, and the spinal cord diameter was 7.8 +/- 0.7 mm. Interobserver agreement was 0.701-0.927 and intraobserver agreement was 0.681-0.937. AADI values obtained on MDCT are significantly lower than those obtained on plain radiography or MRI. PADI values obtained on plain radiography are significantly higher than those obtained on MDCT or MRI. The dural sac width is most closely correlated with PADI values on MDCT. PADI seems to be easier to measure, more relevant, and clinically useful than AADI.

Anterior atlantodental and posterior atlantodental intervals on plain radiography, multidetector CT, and MRI

International Nuclear Information System (INIS)

Cha, Seung Woo; Ryu, Jeong Ah; Park, Dong Woo; Yoon, Ki Bo; Lee, Seung Hun; Joo, Kyung Bin

2015-01-01

To determine the normal values of the anterior atlantodental interval (AADI) and posterior atlantodental interval (PADI) on plain radiography, multidetector CT (MDCT) and MRI, as well as the dural sac width and spinal cord diameter at the atlantoaxial joint level on MRI. In total, 60 subjects underwent plain radiography, MRI and MDCT. We obtained values for AADI and PADI on plain radiography, MDCT, and MRI, and for dural sac width and spinal cord diameter on MRI. Two radiologists independently measured each value and a consensus was reached. The average AADI was 1.5 +/- 0.5 mm on plain radiography, 1.4 +/- 0.3 mm on MDCT, and 1.6 +/- 0.5 mm on MRI. The average PADI was 20.6 +/- 2.4 mm on plain radiography, 18.0 +/- 2.1 mm on MDCT, and 17.7 +/- 1.9 mm on MRI. The dural sac width was 13.7 +/- 1.8 mm, and the spinal cord diameter was 7.8 +/- 0.7 mm. Interobserver agreement was 0.701-0.927 and intraobserver agreement was 0.681-0.937. AADI values obtained on MDCT are significantly lower than those obtained on plain radiography or MRI. PADI values obtained on plain radiography are significantly higher than those obtained on MDCT or MRI. The dural sac width is most closely correlated with PADI values on MDCT. PADI seems to be easier to measure, more relevant, and clinically useful than AADI.

Polarization measurements made on LFRA and OASIS emitter arrays

Science.gov (United States)

Geske, Jon; Sparkman, Kevin; Oleson, Jim; Laveigne, Joe; Sieglinger, Breck; Marlow, Steve; Lowry, Heard; Burns, James

2008-04-01

Polarization is increasingly being considered as a method of discrimination in passive sensing applications. In this paper the degree of polarization of the thermal emission from the emitter arrays of two new Santa Barbara Infrared (SBIR) micro-bolometer resistor array scene projectors was characterized at ambient temperature and at 77 K. The emitter arrays characterized were from the Large Format Resistive Array (LFRA) and the Optimized Arrays for Space-Background Infrared Simulation (OASIS) scene projectors. This paper reports the results of this testing.

Influence of coarse woody debris on the soricid community in southeastern Coastal Plain pine stands.

Energy Technology Data Exchange (ETDEWEB)

Davis, Justin, C.; Castleberry, Steven, B.; Kilgo, John, C.

2010-07-01

Shrew abundance has been linked to the presence of coarse woody debris (CWD), especially downed logs, in many regions in the United States. We investigated the importance of CWD to shrew communities in managed upland pine stands in the southeastern United States Coastal Plain. Using a randomized complete block design, 1 of the following treatments was assigned to twelve 9.3-ha plots: removal (n 5 3; all downed CWD _10 cm in diameter and _60 cm long removed), downed (n 5 3; 5-fold increase in volume of downed CWD), snag (n 5 3; 10-fold increase in volume of standing dead CWD), and control (n 5 3; unmanipulated). Shrews (Blarina carolinensis, Sorex longirostris, and Cryptotis parva) were captured over 7 seasons from January 2007 to August 2008 using drift-fence pitfall trapping arrays within treatment plots. Topographic variables were measured and included as treatment covariates. More captures of B. carolinensis were made in the downed treatment compared to removal, and captures of S. longirostris were greater in downed and snag compared to removal. Captures of C. parva did not differ among treatments. Captures of S. longirostris were positively correlated with slope. Our results suggest that abundance of 2 of the 3 common shrew species of the southeastern Coastal Plain examined in our study is influenced by the presence of CWD.

Usefulness of plain radiography for assessing hypouricemic treatment response in patients with tophaceous gout.

Science.gov (United States)

Suh, Young Sun; Cheon, Yun-Hong; Kim, Ji Eun; Kim, Ji-Min; Kim, Sang-Hyon; Lee, Won-Seok; Yoo, Wan-Hee; Lee, Sang-Il; Kim, Hyun-Ok

2016-11-01

To investigate whether plain radiography is useful for assessing the changes in gouty tophi size following hypouricemic therapy. Gout was diagnosed according to the American College of Rheumatology criteria. Before and after hypouricemic treatment, serum uric acid level was measured, and plain radiography was performed to measure gouty tophi size. The tophi were graded by measuring the maximum vertical and horizontal diameters, and they were scored by adding up the scores of the grades. The vertical diameter was measured on both sides of the proximal phalanges (PPs). The horizontal diameter was measured on the lateral side of the PPs. The maximum vertical diameter measurement was graded 0-4. The maximum horizontal diameter measurement was graded 0-3. Seven hundred first metatarsal phalangeal joints (MTPJ) of 350 patients with gout were assessed for gouty tophi. Tophi were observed using plain radiography in 174 MTPJs (24.9%) of 109 patients (31.1%). Follow-up plain radiography was performed in 60 of these patients. Before the treatment, the average serum uric acid level of these patients was 8.3 ± 1.9 mg/dL, and the average tophi score was 3.7 ± 2.5. After hypouricemic treatment, the uric acid level decreased to 5.9 ± 1.6 mg/dL (P < 0.05), and the average tophi score decreased to 1.5 ± 1.8 (P < 0.05). This new method for measuring gouty tophi using plain radiography may be useful for evaluating changes in gouty tophi size following hypouricemic treatment. © 2016 Asia Pacific League of Associations for Rheumatology and John Wiley & Sons Australia, Ltd.

On measurement of acoustic pulse arrival angles using a vertical array

Science.gov (United States)

Makarov, D. V.

2017-11-01

We consider a recently developed method to analyze the angular structure of pulsed acoustic fields in an underwater sound channel. The method is based on the Husimi transform that allows us to approximately link a wave field with the corresponding ray arrivals. The advantage of the method lies in the possibility of its practical realization by a vertical hydrophone array crossing only a small part of the oceanic depth. The main aim of the present work is to find the optimal parameter values of the array that ensure good angular accuracy and sufficient reliability of the algorithm to calculate the arrival angles. Broadband pulses with central frequencies of 80 and 240 Hz are considered. It is shown that an array with a length of several hundred meters allows measuring the angular spectrum with an accuracy of up to 1 degree. The angular resolution is lowered with an increase of the sound wavelength due to the fundamental limitations imposed by the uncertainty relation.

Measurement techniques and instruments suitable for life-prediction testing of photovoltaic arrays. Interim report

Energy Technology Data Exchange (ETDEWEB)

Noel, G.T.; Sliemers, F.A.; Deringer, G.C.; Wood, V.E.; Wilkes, K.E.; Gaines, G.B.; Carmichael, D.C.

1978-01-15

The validation of a service life of 20 years for low-cost photovoltaic arrays must be accomplished through accelerated life-prediction tests. A methodology for such tests has been developed in a preceding study. The results discussed consist of the initial identification and assessment of all known measurement techniques and instruments that might be used in these life-prediction tests. Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Candidate techniques and instruments are identified on the basis of extensive reviews of published and unpublished information. These methods are organized in six measurement categories--chemical, electrical, optical, thermal, mechanical, and ''other physicals''. Using specified evaluation criteria, the most promising techniques and instruments for use in life-prediction tests of arrays are then selected. These recommended techniques and their characteristics are described. Recommendations are made regarding establishment of the adequacy, particularly with respect to precision, of the more fully developed techniques for this application, and regarding the experimental evaluation of promising developmental techniques. Measurement needs not satisfied by presently available techniques/instruments are also identified.

Analysis of oligonucleotide array experiments with repeated measures using mixed models

Directory of Open Access Journals (Sweden)

Getchell Thomas V

2004-12-01

Full Text Available Abstract Background Two or more factor mixed factorial experiments are becoming increasingly common in microarray data analysis. In this case study, the two factors are presence (Patients with Alzheimer's disease or absence (Control of the disease, and brain regions including olfactory bulb (OB or cerebellum (CER. In the design considered in this manuscript, OB and CER are repeated measurements from the same subject and, hence, are correlated. It is critical to identify sources of variability in the analysis of oligonucleotide array experiments with repeated measures and correlations among data points have to be considered. In addition, multiple testing problems are more complicated in experiments with multi-level treatments or treatment combinations. Results In this study we adopted a linear mixed model to analyze oligonucleotide array experiments with repeated measures. We first construct a generalized F test to select differentially expressed genes. The Benjamini and Hochberg (BH procedure of controlling false discovery rate (FDR at 5% was applied to the P values of the generalized F test. For those genes with significant generalized F test, we then categorize them based on whether the interaction terms were significant or not at the α-level (αnew = 0.0033 determined by the FDR procedure. Since simple effects may be examined for the genes with significant interaction effect, we adopt the protected Fisher's least significant difference test (LSD procedure at the level of αnew to control the family-wise error rate (FWER for each gene examined. Conclusions A linear mixed model is appropriate for analysis of oligonucleotide array experiments with repeated measures. We constructed a generalized F test to select differentially expressed genes, and then applied a specific sequence of tests to identify factorial effects. This sequence of tests applied was designed to control for gene based FWER.

Development and Calibration of a Field-Deployable Microphone Phased Array for Propulsion and Airframe Noise Flyover Measurements

Science.gov (United States)

Humphreys, William M., Jr.; Lockard, David P.; Khorrami, Mehdi R.; Culliton, William G.; McSwain, Robert G.; Ravetta, Patricio A.; Johns, Zachary

2016-01-01

A new aeroacoustic measurement capability has been developed consisting of a large channelcount, field-deployable microphone phased array suitable for airframe noise flyover measurements for a range of aircraft types and scales. The array incorporates up to 185 hardened, weather-resistant sensors suitable for outdoor use. A custom 4-mA current loop receiver circuit with temperature compensation was developed to power the sensors over extended cable lengths with minimal degradation of the signal to noise ratio and frequency response. Extensive laboratory calibrations and environmental testing of the sensors were conducted to verify the design's performance specifications. A compact data system combining sensor power, signal conditioning, and digitization was assembled for use with the array. Complementing the data system is a robust analysis system capable of near real-time presentation of beamformed and deconvolved contour plots and integrated spectra obtained from array data acquired during flyover passes. Additional instrumentation systems needed to process the array data were also assembled. These include a commercial weather station and a video monitoring / recording system. A detailed mock-up of the instrumentation suite (phased array, weather station, and data processor) was performed in the NASA Langley Acoustic Development Laboratory to vet the system performance. The first deployment of the system occurred at Finnegan Airfield at Fort A.P. Hill where the array was utilized to measure the vehicle noise from a number of sUAS (small Unmanned Aerial System) aircraft. A unique in-situ calibration method for the array microphones using a hovering aerial sound source was attempted for the first time during the deployment.

Phased array compaction cell for measurement of the transversely isotropic elastic properties of compacting sediments

Energy Technology Data Exchange (ETDEWEB)

Nihei, K.T.; Nakagawa, S.; Reverdy, F.; Meyer, L.R.; Duranti, L.; Ball, G.

2010-12-15

Sediments undergoing compaction typically exhibit transversely isotropic (TI) elastic properties. We present a new experimental apparatus, the phased array compaction cell, for measuring the TI elastic properties of clay-rich sediments during compaction. This apparatus uses matched sets of P- and S-wave ultrasonic transducers located along the sides of the sample and an ultrasonic P-wave phased array source, together with a miniature P-wave receiver on the top and bottom ends of the sample. The phased array measurements are used to form plane P-waves that provide estimates of the phase velocities over a range of angles. From these measurements, the five TI elastic constants can be recovered as the sediment is compacted, without the need for sample unloading, recoring, or reorienting. This paper provides descriptions of the apparatus, the data processing, and an application demonstrating recovery of the evolving TI properties of a compacting marine sediment sample.

49 CFR 229.64 - Plain bearings.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Plain bearings. 229.64 Section 229.64 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION....64 Plain bearings. A plain bearing box shall contain visible free oil and may not be cracked to the...

Sensitivity Analysis for Hydraulic Behavior of Shiraz Plain Aquifer Using PMWIN

Directory of Open Access Journals (Sweden)

Ahmad Reza karimipour

2011-07-01

Full Text Available In this study, hydraulic behavior of Shirazplain aquifer, with an area of ~300 km2, was simulated using PMWIN model. The performance of recently constructed drainage system in the plain was modeled and parameters affecting hydraulic behavior of the aquifer were analyzed. Measured rainfall and evaporation rates in the plain, recharge and discharge rates through the aqueducts, Khoshk and Chenar Rahdar rivers, as well as amount of water discharged from production wells and recharge due to returned wastewater were considered in the model. Plain hydrodynamic coefficients were estimated via calibration and sensitivity analysis of the model was performed for four important parameters. Results showed that the model is most sensitive to recharge rate and hydraulic conductivity, respectively, such that a small variation in these two parameters causes a dramatic change in hydraulic head distribution in the plain. Furthermore, specific yield coefficient influences the seasonal water level fluctuations, but the aqueducts conductance coefficient only affects the aqueduct radius of influence with little effect on the overall hydraulic behavior of the plain.

Heat flow measurements in Great Meteor East, Madeira Abyssal Plain, during Discovery Cruise 144

International Nuclear Information System (INIS)

Noel, M.

1984-01-01

This report describes 21 closely spaced heat flow measurements which were made along two survey lines in an area of faulted sediments east of Great Meteor Seamount in the Madeira Abyssal Plain. The heat flow was found to be correlated with basement topography as mapped by seismic reflection profiling. Data modelling suggests that this is due both to the thermal conductivity contrast between sediments and basement rocks and to the presence of hydrothermal circulation within basement highs. The existence of non-linear temperature profiles in sediments covering basement highs suggests that the underlying circulation is causing an upward movement of porewater. There is no firm evidence to show that the sediment faults act as preferred pathways for porewater advection. (author)

Uranium in pore waters from North Atlantic (GME and Southern Nares Abyssal Plain) sediments

International Nuclear Information System (INIS)

Santschi, P.H.; Bajo, C.; Mantovani, M.; Orciuolo, D.; Cranston, R.E.; Bruno, J.

1988-01-01

Here we report the measurement of low uranium concentrations in composite pore-water samples from the uppermost 20-30 m of deep-sea abyssal plain sediments from the Great Meteor East and Southern Nares Abyssal Plains Area. Many values are the lowest uranium concentrations ever measured in the pore waters of deep-sea sediments. Our lowest value, 0.05 ± 0.01 p.p.b., is orders of magnitude lower than the predicted solubility of U0 2 or U 4 0 9 . The uranium concentrations obtained from both sites correlate closely with measured redox potentials in the sediments. The low mobility of uranium in pore waters from turbiditic deep-sea abyssal plain sediments, which can be deduced from these measurements, has important implications for the sub-seabed disposal of high-level radioactive waste, and for marine geochemistry of uranium. (author)

Terrain And Laboratory Conductivity Studies Of Flood Plains Of ...

African Journals Online (AJOL)

A shallow electromagnetic study (electrical conductivity and magnetic susceptibility measurements) and laboratory conductivity sampling of the flood plains of Oluwatuyi/Oshinle area of Akure have been undertaken. This is with the aim of correlating the terrain conductivity mapping with laboratory measurements to establish ...

Radiocesium in wheat of the Po plain

International Nuclear Information System (INIS)

Dominici, G.; Malvicini, A.

1988-01-01

The Cs-137 measurements of many wheat samples, which was cultivated in Po plain during 1986 and 1987, are reported. A relationship is also shown between the quantity of Cs-137, which is contained in total fall-out, and that in the wheat by direct deposition

Climate variability and Great Plains agriculture

International Nuclear Information System (INIS)

Rosenberg, N.J.; Katz, L.A.

1991-01-01

The ways in which inhabitants of the Great Plains, including Indians, early settlers, and 20th century farmers, have adapted to climate changes on the Great Plains are explored. The climate of the Great Plains, because of its variability and extremes, can be very stressful to plants, animals and people. It is suggested that agriculture and society on the Great Plains have, during the last century, become less vulnerable to the stresses imposed by climate. Opinions as to the sustainability of agriculture on the Great Plains vary substantially. Lockeretz (1981) suggests that large scale, high cost technologies have stressed farmers by creating surpluses and by requiring large investments. Opie (1989) sees irrigation as a climate substitute, however he stresses that the Ogallala aquifer must inevitably become depleted. Deborah and Frank Popper (1987) believe that farming on the Plains is unsustainable, and destruction of shelterbelts, out-migration of the rural population and environmental problems will lead to total collapse. With global warming, water in the Great Plains is expected to become scarcer, and although improvements in irrigation efficiency may slow depletion of the Ogallala aquifer, ultimately the acreage under irrigation must decrease to levels that can be sustained by natural recharge and reliable surface flows. 23 refs., 2 figs

Flexible Micropost Arrays for Shear Stress Measurement

Science.gov (United States)

Wohl, Christopher J.; Palmieri, Frank L.; Hopkins, John W.; Jackson, Allen M.; Connell, John W.; Lin, Yi; Cisotto, Alexxandra A.

2015-01-01

Increased fuel costs, heightened environmental protection requirements, and noise abatement continue to place drag reduction at the forefront of aerospace research priorities. Unfortunately, shortfalls still exist in the fundamental understanding of boundary-layer airflow over aerodynamic surfaces, especially regarding drag arising from skin friction. For example, there is insufficient availability of instrumentation to adequately characterize complex flows with strong pressure gradients, heat transfer, wall mass flux, three-dimensionality, separation, shock waves, and transient phenomena. One example is the acoustic liner efficacy on aircraft engine nacelle walls. Active measurement of shear stress in boundary layer airflow would enable a better understanding of how aircraft structure and flight dynamics affect skin friction. Current shear stress measurement techniques suffer from reliability, complexity, and airflow disruption, thereby compromising resultant shear stress data. The state-of-the-art for shear stress sensing uses indirect or direct measurement techniques. Indirect measurements (e.g., hot-wire, heat flux gages, oil interferometry, laser Doppler anemometry, small scale pressure drag surfaces, i.e., fences) require intricate knowledge of the studied flow, restrictive instrument arrangements, large surface areas, flow disruption, or seeding material; with smaller, higher bandwidth probes under development. Direct measurements involve strain displacement of a sensor element and require no prior knowledge of the flow. Unfortunately, conventional "floating" recessed components for direct measurements are mm to cm in size. Whispering gallery mode devices and Fiber Bragg Gratings are examples of recent additions to this type of sensor with much smaller (?m) sensor components. Direct detection techniques are often single point measurements and difficult to calibrate and implement in wind tunnel experiments. In addition, the wiring, packaging, and installation

Influence of Relief on Vegetation Factors and Agrotechnical Differentiation Measures in Transylvania Plain

Science.gov (United States)

Ioana Moraru, Paula; Rusu, Teodor; Bogdan, Ileana; Ioan Pop, Adrian

2016-04-01

Transylvanian Plain (TP), with an area of 395.616 hectares, has a special importance for Romanian agriculture being characterized as a region orographically represented by hilly areas hills whereas climatically appears as a plain. Physical-geographical conditions from TP (low level of forestation; climate specific to plains) have resulted in numerous land degradation phenomena: land erosion, landslide, draining of gradient springs and groundwater level. These conditions create a favourable framework for the development of anthropic morphogenetic processes, as well as those triggered by natural mechanisms, thus intensifying the pace and their territorial expansion. Rainfall, through annual distribution and spring-summer pluvial aggressiveness, require the implementation of preservation measures on arable land, particularly for spring cultures. Along with rainfall, more factors are involved: relief, by the high degree of fragmentation and through tilting slopes; vegetation, by the dominance of cultivated plants and by the advanced state of degradation of vegetal grasslands (especially on southern slopes); lithology, by the predominance of loose rocks (sand, marl, sandstone etc.). In order to determine the influence of landscape morphology on the agro-technical characterization of land, 11 HOBO Micro Stations (H21-002) have been implemented from April to October in the locality Caianu, at various altitudes (311-441 m) at exposure coverage (N, NW, W, S, SE, E, NE). HOBO Smart Temp (S-TMB-M002) temperature sensors and Decagon EC-5 (S-SMC-M005) moisture sensors were connected to HOBO Micro Stations. Additionally, in 4 of the 11 sites, tipping bucket rain gauges (RG3-M) were deployed to measure precipitation. Each station stored electronic data regarding ground temperature at 3 depths (10, 20, 30 cm), humidity at a depth of 10 cm, air temperature (1 m) and precipitation. Data were downloaded from the Micro Stations via a laptop computer using HOBOware Pro Software Version

Analysis of tumor-like shadows on abdominal plain x-ray film

International Nuclear Information System (INIS)

Hayashi, Hidehiro; Hiraki, Yoshio; Hashimoto, Keizi

1986-01-01

We found tumor-like shadows in the upper abdomen in 93 cases out of 400 abdominal plain films, although none of these 93 cases actually had a tumor. We analyzed these tumor-like shadows by computed tomography. For each of the 400 cases we measured the width of flank stripe on the abdominal plain film. Most of the tumor-like shadows in the left upper abdomen were gastric fundus, but it was significant for evaluating plain abdominal film that other organs such as a part of the left lobe of the liver, the upper pole of the left kidney, and a part of the spleen formed tumor-like shadows. The most important factors forming tumor-like shadows on plain abdominal film are the fat volume of the abdominal cauity as well as the fraciform ligament and alterations in the shape and volume of organs such as occur in liver cirrhosis. (author)

Design and implementation of a low-cost multichannel seismic noise recorder for array measurements

Science.gov (United States)

Soler-Llorens, Juan Luis; Juan Giner-Caturla, Jose; Molina-Palacios, Sergio; Galiana-Merino, Juan Jose; Rosa-Herranz, Julio; Agea-Medina, Noelia

2017-04-01

Soil characterization is the starting point for seismic hazard studies. Currently, the methods based on ambient noise measurements are very used because they are non-invasive methods and relatively easy to implement in urban areas. Among these methods, the analysis of array measurements provides the dispersion curve and subsequently the shear-wave velocity profile associated to the site under study. In this case, we need several sensors recording simultaneously and a data acquisition system with one channel by sensor, what can become the complete equipment unaffordable for small research groups. In this work, we have designed and implemented a low-cost multichannel ambient noise recorder for array measurements. The complete system is based on Arduino, an open source electronic development platform, which allows recording 12 differential input channels simultaneously. Besides, it is complemented with a conditioning circuit that includes an anti-aliasing filter and a selectable gain between 0 and 40dB. The data acquisition is set up through a user-friendly graphical user interface. It is important to note that the electronic scheme as well as the programming code are open hardware and software, respectively, so it allows other researchers to suite the system to their particular requirements. The developed equipment has been tested at several sites around the province of Alicante (southeast of Spain), where the soil characteristics are well-known from previous studies. Array measurements have been taken and after that, the recorded data have been analysed using the frequency-wavenumber (f-k) and the extended spatial autocorrelation (ESAC) methods. The comparison of the obtained dispersion curves with the ones obtained in previous studies shows the suitability of the implemented low-cost system for array measurements.

[The plain packaging of tobacco products: a new strategy for tobacco control].

Science.gov (United States)

Rey-Pino, Juan Miguel; Nerín, Isabel; Lacave-García, Ma Blanca

There is evidence that global tobacco smoking control policies contribute to decrease the prevalence of smoking among populations, so there is a need to effectively implement different measures in a coordinated way. The plain packaging and labelling of tobacco products is one of the measures proposed by the World Health Organisation Framework Convention on Tobacco Control. At the moment, leading countries are implementing this tobacco control measure, which involves a plain packaging for all tobacco products, i.e., the absence of any promotional or communication tool in the packaging, except the name of the brand, appearing with a standardised font, size, colour and placing in the pack. Australia was the first country to implement this measure in 2012 and recently other countries are legislating and approving it. In Spain, tobacco legislation (2005 and 2010), was an important advance in tobacco control policies. The introduction of plain packaging in Spain would mean the next step in the development of a global strategy for fighting this significant health problem. The aim of this article is to synthesise in a structured manner the role that the packaging of tobacco products has within marketing and communication strategies, as well as to describe the potential effects that the plain packaging has on some aspects of smoking behaviour, according to current literature. Copyright © 2016 SESPAS. Publicado por Elsevier España, S.L.U. All rights reserved.

Simulation of surface cracks measurement in first walls by laser spot array thermography

Energy Technology Data Exchange (ETDEWEB)

Pei, Cuixiang; Qiu, Jinxin; Liu, Haocheng; Chen, Zhenmao, E-mail: chenzm@mail.xjtu.edu.cn

2016-11-01

The inspection of surface cracks in first walls (FW) is very important to ensure the safe operation of the fusion reactors. In this paper, a new laser excited thermography technique with using laser spot array source is proposed for the surface cracks imaging and evaluation in the FW with an intuitive and non-contact measurement method. Instead of imaging a crack by scanning a single laser spot and superimposing the local discontinuity images with the present laser excited thermography methods, it can inspect a relatively large area at one measurement. It does not only simplify the measurement system and data processing procedure, but also provide a faster measurement for FW. In order to investigate the feasibility of this method, a numerical code based on finite element method (FEM) is developed to simulate the heat flow and the effect of the crack geometry on the thermal wave fields. An imaging method based on the gradient of the thermal images is proposed for crack measurement with the laser spot array thermography method.

Tobacco branding, plain packaging, pictorial warnings, and symbolic consumption.

Science.gov (United States)

Hoek, Janet; Gendall, Philip; Gifford, Heather; Pirikahu, Gill; McCool, Judith; Pene, Gina; Edwards, Richard; Thomson, George

2012-05-01

We use brand association and symbolic consumption theory to explore how plain cigarette packaging would influence the identities young adults cocreate with tobacco products. Group discussions and in-depth interviews with 86 young adult smokers and nonsmokers investigated how participants perceive tobacco branding and plain cigarette packaging with larger health warnings. We examined the transcript data using thematic analysis and explored how removing tobacco branding and replacing this with larger warnings would affect the symbolic status of tobacco brands and their social connotations. Smokers used tobacco brand imagery to define their social attributes and standing, and their connection with specific groups. Plain cigarette packaging usurped this process by undermining aspirational connotations and exposing tobacco products as toxic. Replacing tobacco branding with larger health warnings diminishes the cachet brand insignia creates, weakens the social benefits brands confer on users, and represents a potentially powerful policy measure.

Continuous-Scan Phased Array Measurement Methods for Turbofan Engine Acoustic Testing, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — ATA Engineering, Inc., (ATA) proposes an SBIR project to advance the technology readiness level (TRL) of a method for measuring phased array acoustic data for...

Development of a Tonometric Sensor with a Decoupled Circular Array for Precisely Measuring Radial Artery Pulse

Directory of Open Access Journals (Sweden)

Min-Ho Jun

2016-05-01

Full Text Available The radial artery pulse is one of the major diagnostic indices used clinically in both Eastern and Western medicine. One of the prominent methods for measuring the radial artery pulse is the piezoresistive sensor array. Independence among channels and an appropriate sensor arrangement are important for effectively assessing the spatial-temporal information of the pulse. This study developed a circular-type seven-channel piezoresistive sensor array using face-down bonding (FDB as one of the sensor combination methods. The three-layered housing structure that included independent pressure sensor units using the FDB method not only enabled elimination of the crosstalk among channels, but also allowed various array patterns to be created for effective pulse measurement. The sensors were arranged in a circular-type arrangement such that they could estimate the direction of the radial artery and precisely measure the pulse wave. The performance of the fabricated sensor array was validated by evaluating the sensor sensitivity per channel, and the possibility of estimating the blood vessel direction was demonstrated through a radial artery pulse simulator. We expect the proposed sensor to allow accurate extraction of the pulse indices for pulse diagnosis.

Unpacking the Right to plain and understandable Language in the Consumer Protection Act 68 of 2008

Directory of Open Access Journals (Sweden)

Philip N Stoop

2013-12-01

Full Text Available The Consumer Protection Act 68 of 2008 came into effect on 1 April 2011. The purpose of this Act is, among other things, to promote fairness, openness and respectable business practice between the suppliers of goods or services and the consumers of such good and services. In consumer protection legislation fairness is usually approached from two directions, namely substantive and procedural fairness. Measures aimed at procedural fairness address conduct during the bargaining process and generally aim at ensuring transparency. Transparency in relation to the terms of a contract relates to whether the terms of the contract terms accessible, in clear language, well-structured, and cross-referenced, with prominence being given to terms that are detrimental to the consumer or because they grant important rights. One measure in the Act aimed at addressing procedural fairness is the right to plain and understandable language. The consumer’s right to being given information in plain and understandable language, as it is expressed in section 22, is embedded under the umbrella right of information and disclosure in the Act. Section 22 requires that notices, documents or visual representations that are required in terms of the Act or other law are to be provided in plain and understandable language as well as in the prescribed form, where such a prescription exists. In the analysis of the concept “plain and understandable language” the following aspects are considered in this article: the development of plain language measures in Australia and the United Kingdom; the structure and purpose of section 22; the documents that must be in plain language; the definition of plain language; the use of official languages in consumer contracts; and plain language guidelines (based on the law of the states of Pennsylvania and Connecticut in the United States of America.

A BaF2 crystal array for high energy-ray measurements

Indian Academy of Sciences (India)

Abstract. We shall discuss about the scientific motivation and construction of a 7 × 7 BaF2 crystal array at Variable Energy Cyclotron Centre, Calcutta. This detector would be used to measure high energy -ray photons from GDR decay and proton–neutron bremsstrahlung reactions at the present 88'' cyclotron and upcoming ...

Testing of focal plane arrays

International Nuclear Information System (INIS)

Merriam, J.D.

1988-01-01

Problems associated with the testing of focal plane arrays are briefly examined with reference to the instrumentation and measurement procedures. In particular, the approach and instrumentation used as the Naval Ocean Systems Center is presented. Most of the measurements are made with flooded illumination on the focal plane array. The array is treated as an ensemble of individual pixels, data being taken on each pixel and array averages and standard deviations computed for the entire array. Data maps are generated, showing the pixel data in the proper spatial position on the array and the array statistics

Analysis of measurements on wind turbine arrays. Vol. 1

International Nuclear Information System (INIS)

Hoeg, E.

1990-12-01

In 1989 a Danish electric power company initiated an analysis of eight wind turbine arrays. Data from this project is presented together with the explained results of the analyses and the output variations for individual arrays and for systems within the arrays. The models for prognosis are compared and evaluated in order to find that which is most effective. (AB)

Dispersion measurements from Sofar floats on the Iberian Abyssal plain

International Nuclear Information System (INIS)

Rees, J.M.; Gmitrowicz, M.

1989-01-01

Tracks of SOFAR floats launched on the Iberian Abyssal Plain are presented. The floats were launched in two groups in early October 1984 and mid-February 1985 to a nominal depth of 2500 m. Of these floats, 4 from the first deployment and 2 from the second functioned properly. Float signals were recorded by four autonomous listening stations at a depth of 1900 m. These preliminary results show the tracks of floats up to July 1986 and represent 3600 float days of information. The main task of the experiment was to especially study the dispersion of radioactive substances

Experimental evaluation of residual stresses produced by plain dents in pipelines

Energy Technology Data Exchange (ETDEWEB)

Pascotto, Jorge [PETROBRAS Transporte S.A. (TRANSPETRO), Rio de Janeiro, RJ (Brazil); Marques, Altino; Fonseca, Maria Cindra [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil)

2009-07-01

A dent means a permanent plastic deformation of the circular cross-section of the pipe. Dents are potentially danger for structural integrity of onshore and offshore pipelines, because it causes a local stress and strain concentration. It is also expected that residual stresses are introduced by the non-uniform plastic deformation. A plain dent is a dent which causes a smooth change in the curvature of the pipe wall that contains no wall thickness reductions (such as a gouge or a crack) or other defects or imperfections (such as a weld). This work presents an experimental evaluation of residual stresses intensification due to plain dents introduced through the same indentation process, in samples made of the same steel line pipe, commonly used in the pipeline industry. The residual stresses were measured in the longitudinal and circumferential directions in preselected points by X-ray diffraction technique, before indentation. After the samples have been dented, the residual stresses were measured once more at the same points, for comparison. All samples presented a similar behavior of the residual stresses due to induced plain dents, and the X-ray diffraction technique shows itself as an efficient methodology of stress measurement in pipelines. (author)

44 CFR 10.14 - Flood plains and wetlands.

Science.gov (United States)

2010-10-01

... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Flood plains and wetlands. 10... Flood plains and wetlands. For any action taken by FEMA in a flood plain or wetland, the provisions of... Executive Order 11988, Flood Plain Management, and Executive Order 11990, Protection of Wetlands (44 CFR...

Copper vertical micro dendrite fin arrays and their superior boiling heat transfer capability

Science.gov (United States)

Wang, Ya-Qiao; Lyu, Shu-Shen; Luo, Jia-Li; Luo, Zhi-Yong; Fu, Yuan-Xiang; Heng, Yi; Zhang, Jian-Hui; Mo, Dong-Chuan

2017-11-01

Micro pin fin arrays have been widely used in electronic cooling, micro reactors, catalyst support, and wettability modification and so on, and a facile way to produce better micro pin fin arrays is demanded. Herein, a simple electrochemical method has been developed to fabricate copper vertical micro dendrite fin arrays (Cu-VMDFA) with controllable shapes, number density and height. High copper sulphate concentration is one key point to make the dendrite stand vertically. Besides, the applied current should rise at an appropriate rate to ensure the copper dendrite can grow vertically on its own. The Cu-VMDFA can significantly enhance the heat transfer coefficient by approximately twice compared to the plain copper surface. The Cu-VMDFA may be widely used in boiling heat transfer areas such as nuclear power plants, electronic cooling, heat exchangers, and so on.

Defining 'plain language' in contemporary South Africa | Cornelius ...

African Journals Online (AJOL)

Defining the concept 'plain language' has been hugely problematic since the origins of the socalled Plain Language Movement in the 1970s in the United States and elsewhere in the world. Definitions of 'plain language' abound, yet James (2008: 6) warns, in relation to plain language practitioners, that “we can't yet call ...

7 CFR 650.25 - Flood-plain management.

Science.gov (United States)

2010-01-01

... user how alternative land use decisions may affect the aquatic and terrestial ecosystems, human safety... Flood-plain management. Through proper planning, flood plains can be managed to reduce the threat to... encourages sound flood-plain management decisions by land users. (a) Policy—(1) General. NRCS provides...

Southern Great Plains Safety Orientation

Energy Technology Data Exchange (ETDEWEB)

Schatz, John

2014-05-01

Welcome to the Atmospheric Radiation Measurement (ARM) Climate Research Facility (ARM) Southern Great Plains (SGP) site. This U.S. Department of Energy (DOE) site is managed by Argonne National Laboratory (ANL). It is very important that all visitors comply with all DOE and ANL safety requirements, as well as those of the Occupational Safety and Health Administration (OSHA), the National Fire Protection Association, and the U.S. Environmental Protection Agency, and with other requirements as applicable.

Phased Array Noise Source Localization Measurements Made on a Williams International FJ44 Engine

Science.gov (United States)

Podboy, Gary G.; Horvath, Csaba

2010-01-01

A 48-microphone planar phased array system was used to acquire noise source localization data on a full-scale Williams International FJ44 turbofan engine. Data were acquired with the array at three different locations relative to the engine, two on the side and one in front of the engine. At the two side locations the planar microphone array was parallel to the engine centerline; at the front location the array was perpendicular to the engine centerline. At each of the three locations, data were acquired at eleven different engine operating conditions ranging from engine idle to maximum (take off) speed. Data obtained with the array off to the side of the engine were spatially filtered to separate the inlet and nozzle noise. Tones occurring in the inlet and nozzle spectra were traced to the low and high speed spools within the engine. The phased array data indicate that the Inflow Control Device (ICD) used during this test was not acoustically transparent; instead, some of the noise emanating from the inlet reflected off of the inlet lip of the ICD. This reflection is a source of error for far field noise measurements made during the test. The data also indicate that a total temperature rake in the inlet of the engine is a source of fan noise.

Phased Acoustic Array Measurements of a 5.75 Percent Hybrid Wing Body Aircraft

Science.gov (United States)

Burnside, Nathan J.; Horne, William C.; Elmer, Kevin R.; Cheng, Rui; Brusniak, Leon

2016-01-01

Detailed acoustic measurements of the noise from the leading-edge Krueger flap of a 5.75 percent Hybrid Wing Body (HWB) aircraft model were recently acquired with a traversing phased microphone array in the AEDC NFAC (Arnold Engineering Development Complex, National Full Scale Aerodynamics Complex) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The spatial resolution of the array was sufficient to distinguish between individual support brackets over the full-scale frequency range of 100 to 2875 Hertz. For conditions representative of landing and take-off configuration, the noise from the brackets dominated other sources near the leading edge. Inclusion of flight-like brackets for select conditions highlights the importance of including the correct number of leading-edge high-lift device brackets with sufficient scale and fidelity. These measurements will support the development of new predictive models.

49 CFR 215.111 - Defective plain bearing.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective plain bearing. 215.111 Section 215.111... § 215.111 Defective plain bearing. A railroad may not place or continue in service a car, if the car has a plain bearing— (a) That is missing, cracked, or broken; (b) On which the bearing liner— (1) Is...

Geomorphology of the Namoi alluvial plain, northwestern New South Wales

International Nuclear Information System (INIS)

Young, R.W.; Young, A.R.M.; Price, D.M.; Wray, R.A.L.

2002-01-01

The Quaternary history of the extensive alluvial plains of the northern part of the Darling River Basin has received little attention, and has generally been assumed to be an analogue of the very detailed history compiled for the Riverine Plain of southeastern Australia. Our study of the Namoi valley, which is a tributary to the upper Darling, shows that this assumption is unfounded. Thermoluminescence dating demonstrates that the oldest palaeochannels of the Namoi River correspond only to the youngest palaeochannels on the Riverine Plain. The thermoluminescence analyses were carried out on the 90-125 μm quartz fraction thermally stimulated by ionizing radiation using the combined additive/regenerative technique. This technique utilises a second glow normalisation procedure that involves re-irradiating each of the quartz sample aliquots and measuring the thermoluminescence induced in the grains. It has ben demonstrated that unlike the streams on the Riverine Plain, the Namoi River has moved progressively away from its buried Tertiary palaeovalley, probably due to declining sediment input from its southern tributaries. In contrast to the streams of the Riverine Plain, the dimensions of the Namoi palaeochannels are indicative of substantially greater discharges until the mid-Holocene. There is also evidence of significant aeolian input throughout the Late Quaternary. The study indicates that the water resources of this increasingly important irrigated region seem to be considerably constrained by the Quaternary heritage of the Namoi valley. Copyright (2002) Geological Society of Australia

Characteristics and measurement of supersonic projectile shock waves by a 32-microphone ring array

Science.gov (United States)

Chang, Ho; Wu, Yan-Chyuan; Tsung, Tsing-Tshih

2011-08-01

This paper discusses about the characteristics of supersonic projectile shock wave in muzzle region during firing of high explosive anti-tank (HEAT) and high explosive (HE) projectiles. HEAT projectiles are fired horizontally at a muzzle velocity of Mach 3.5 from a medium caliber tank gun equipped with a newly designed multi-perforated muzzle brake, whereas HE projectiles are fired at elevation angles at a muzzle velocity of Mach 2 from a large caliber howitzer equipped with a newly designed double-baffle muzzle brake. In the near field, pressure signatures of the N-wave generated from projectiles are measured by 32-microphone ring array wrapped by cotton sheath. Records measured by the microphone array are used to demonstrate several key characteristics of the shock wave of supersonic projectile. All measurements made in this study can be a significant reference for developing guns, tanks, or the chassis of fighting vehicles.

Guesstimation of posterior malleolar fractures on lateral plain radiographs

NARCIS (Netherlands)

Meijer, D. T.; Doornberg, J. N.; Sierevelt, I. N.; Mallee, W. H.; van Dijk, C. N.; Kerkhoffs, G. M.; Stufkens, S. A.; Palmanovich, Ezequiel; van Sterkenburg, Maayke; Engvall, Andreas; Arroyo, Ernesto; Golovakha, Maksym; Pereira, Ernesto; Josep Torrent, Eugene Toh; Haverkamp, Daniel; Bojanic, Ivan; Sousa, Manuel; Aragon, Oscar Castro; Russo, Alessandro; Cortes, Carlos; Pánics, Gergely; Vide, João; Spanos, Loannis; Carvalho, Manuel Santos; Maggi, Pablo; Thomas, Zach; Tanaka, Hirofumi; Dinato, Mauro; Fay, Jakob; Kimtys, Vytautas; Correia Moreira, António José; Hatziemmanuil, Dimitrios; Low, Tze-Choong; van der Plaat, Laurens Wessel; Mora, Allan David; van Rensen, Inge; del Vecchio, Javier; Ramos, James; Azevedo, Jorge; Bustamante, Carlos; Oliveira, Alexandre; Zaw, Htwe; Kurup, Harish; Yli-Kyyny, Tero; Baca, Emre; Haapasalo, Heidi; Bakhtamyan, Gurgen; Zbikowski, Piotr; van den Bekerom, Michel; de Muinck Keizer, Robert-Jan

2015-01-01

Accurate assessment of articular involvement of the posterior malleolar fracture fragments in ankle fractures is essential, as this is the leading argument for internal fixation. The purpose of this study is to assess diagnostic accuracy of measurements on plain lateral radiographs. Quantification

SU-E-T-228: Liquid Ionisation Chamber Array and MicroDiamond Measurements with the CyberKnife System

International Nuclear Information System (INIS)

Poppinga, D; Looe, H; Stelljes, T; Poppe, B; Blanck, O; Harder, D

2014-01-01

Purpose: The aim of this study was to measure the dose profile and output factors with a CyberKnife accelerator using a TM60019 microDiamond detector and a 1000SRS liquid chamber array (both PTW Freiburg, Germany). Methods: An MP3 water phantom (PTW, Freiburg) was positioned along the robotic world coordinate system. The TM60019 detector was adjusted to the center of the according fields and the semiconductor axis was aligned with the beam direction. Profiles at 5cm water depth and SSD = 80 cm were measured along the robotic x axis and y axis for the cylindrical collimators of the CyberKnife (diameter 60, 50, 40, 30, 20, 15, 12.5, 10, 7.5 and 5mm). To determine the output factors the dose profile was measured at 0.1 mm steps around the field center to find the maximum dose value. The liquid chamber array (1000SRS) measurement was performed with the same setup, but with RW3 buildup. Results: The 1000SRS measurements closely conform with the TM60019 profile measurement in all profile regions and for all collimator sizes. The profile measurement is influenced by the almost equal spatial resolution of the TM60019 detector (radius of the sensitive area 1.1mm) and of the 1000SRS liquid chamber array (single chamber width 2.3mm). The measured dose profiles have not been corrected for this limited spatial resolution. Rather we purpose to consider that spatial dose averaging over 2 mm wide regions might be justified in view of patient positioning inaccuracies and of the spaces in tissue participating in the biological radiation responses. Conclusion: The 1000SRS data points conform with the TM60019 profile measurements at all profile regions showing the applicability of liquid ion chamber arrays with the CyberKnife system

SU-E-T-228: Liquid Ionisation Chamber Array and MicroDiamond Measurements with the CyberKnife System

Energy Technology Data Exchange (ETDEWEB)

Poppinga, D; Looe, H; Stelljes, T; Poppe, B [University of Oldenburg, Oldenburg, Lower Saxony (Germany); Blanck, O [CyberKnife Zentrum Norddeutschland, Guestrow (Germany); Harder, D [Georg August University, Goettingen, Niedersachsen (Germany)

2014-06-01

Purpose: The aim of this study was to measure the dose profile and output factors with a CyberKnife accelerator using a TM60019 microDiamond detector and a 1000SRS liquid chamber array (both PTW Freiburg, Germany). Methods: An MP3 water phantom (PTW, Freiburg) was positioned along the robotic world coordinate system. The TM60019 detector was adjusted to the center of the according fields and the semiconductor axis was aligned with the beam direction. Profiles at 5cm water depth and SSD = 80 cm were measured along the robotic x axis and y axis for the cylindrical collimators of the CyberKnife (diameter 60, 50, 40, 30, 20, 15, 12.5, 10, 7.5 and 5mm). To determine the output factors the dose profile was measured at 0.1 mm steps around the field center to find the maximum dose value. The liquid chamber array (1000SRS) measurement was performed with the same setup, but with RW3 buildup. Results: The 1000SRS measurements closely conform with the TM60019 profile measurement in all profile regions and for all collimator sizes. The profile measurement is influenced by the almost equal spatial resolution of the TM60019 detector (radius of the sensitive area 1.1mm) and of the 1000SRS liquid chamber array (single chamber width 2.3mm). The measured dose profiles have not been corrected for this limited spatial resolution. Rather we purpose to consider that spatial dose averaging over 2 mm wide regions might be justified in view of patient positioning inaccuracies and of the spaces in tissue participating in the biological radiation responses. Conclusion: The 1000SRS data points conform with the TM60019 profile measurements at all profile regions showing the applicability of liquid ion chamber arrays with the CyberKnife system.

The cosmic-ray energy spectrum above 1016 eV measured with the LOFAR radboud air shower array

NARCIS (Netherlands)

Thoudam, S.; Buitink, S.; Corstanje, A.; Enriquez, J. E.; Falcke, H.; Hörandel, J. R.; Nelles, A.; Rachen, J. P.; Rossetto, L.; Schellart, P.; Scholten, O.; Ter Veen, S.; Trinh, T. N G; Van Kessel, L.

2015-01-01

The LOFAR Radboud Air Shower Array (LORA) is an array of 20 plastic scintillation detectors installed in the center of the LOFAR radio telescope in the Netherlands to measure extensive air showers induced by cosmic rays in the Earth's atmosphere. The primary goals of LORA are to trigger the read-out

Microscopic composition measurements of organic individual particles collected in the Southern Great Plains

Science.gov (United States)

Bonanno, D.; China, S.; Fraund, M. W.; Pham, D.; Kulkarni, G.; Laskin, A.; Gilles, M. K.; Moffet, R.

2016-12-01

The Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems (HI-SCALE) Campaign was carried out to gain a better understanding of the lifecycle of shallow clouds. The HISCALE experiment was designed to contrast two seasons, wet and dry, and determine their effect on atmospheric cloud and aerosol processes. The spring component to HISCALE was selected to characterize mixing state for particles collected onto substrates. Sampling was performed before and after rain events to obtain airborne soil organic particles (ASOP), which are ejected after rain events. The unique composition of the ASOP may affect optical properties and/or hygroscopic properties. The collection of particles took place at the Atmospheric Radiation Measurement Southern Great Plains (ARM SGP) field site. The Scanning Transmission X-Ray Microscope (STXM) was used to image the samples collected during the first HI-SCALE Campaign to determine the carbonaceous mixing state. Scanning Electron Microscopy Energy-dispersive X-ray (SEM/EDX) analysis is more sensitive to the inorganic makeup of particles, while STXM renders a more comprehensive analysis of the organics. Measurements such as nephelometry, Particle Soot Absorption Photometry (PSAP), and Aerosol Mass Spectrometry (AMS) from the ARM archive will be correlated with microscopy measurements. The primary focus is the relation between composition and morphology of ASOP with hygroscopicity and optical properties. Further investigation of these organic particles will be performed to provide a mixing state parameterization and aid in the advancement of current climate models.

Chenier plain development: feedbacks between waves, mud and sand

Science.gov (United States)

Nardin, W.; Fagherazzi, S.

2015-12-01

Cheniers are sandy ridges parallel to the coast established by high energy waves. Here we discuss Chenier plains ontogeny through dimensional analysis and numerical results from the morphodynamic model Delft3D-SWAN. Our results show that wave energy and shelf slope play an important role in the formation of Chenier plains. In our numerical experiments waves affect Chenier plain development in three ways: by winnowing sediment from the mudflat, by eroding mud and accumulating sand over the beach during extreme wave events. We further show that different sediment characteristics and wave climates can lead to three alternative coastal landscapes: strand plains, mudflats, or the more complex Chenier plains. Low inner-shelf slopes are the most favorable for strand plain and Chenier plain formation, while high slopes decrease the likelihood of mudflat development and preservation.

Intussusception in childhood: the role of plain abdominal radiographs

International Nuclear Information System (INIS)

Ji, Joo Yun; Kim, Min Joong; Kim, Young Mook; Park, Won Gyu; Ko, Kang Seok; Kim, Se Jong; Park, Byung Ran; Kim, Byong Geun

1995-01-01

The purposes of this study were to evaluate the plain radiologic findings of the childhood intussusception and to evaluate the role of plain abdominal films in predicting the success of air or barium reduction. We retrospectively reviewed 140 cases with the diagnosis of intussusception in childhood. The radiological signs that included soft tissue mass, dilatation of small bowel suggesting obstruction, crescent sign, and target sign were evaluated in terms of frequency. The relationship between radiological findings and outcome of reduction was analyzed. The site of soft tissue mass or crescent sign seen on plain radiographs was correlated with the position of the apex of the intussusceptum seen at the beginning of barium edema. The degree of dilated small bowel was evaluated by calculating the proportion of air-filled small bowel occupying peritoneal cavity and measuring the maximal diameter of dilated bowel lumen. The radiological finding for small bowel obstruction is determined by observation of the degree of small bowel dilatation and/or air-fluid levels. Ninety-two cases out of 140 showed one or more radiographic signs. Two most common signs were soft tissue mass and small bowel obstruction. The success rate of air or barium reduction was significantly lower in patients with most severe degree of dilatation of small bowel and/or more than 7 air-fluid levels on erect view. The suspected location of intussusception on plain radiographs correlated well with the true location of intussusception seen in the first few seconds of barium reduction. Plain abdominal radiography is useful in the diagnosis of intussusception and provides helpful information for the reduction procedure as well as for the exclusion of the contraindications such as bowel perforation

The effect of cigarette branding and plain packaging on female youth in the United Kingdom.

Science.gov (United States)

Hammond, David; Daniel, Samantha; White, Christine M

2013-02-01

Cigarette packaging is the most prominent form of tobacco marketing remaining in countries such as the United Kingdom. The current study examined perceptions of cigarette packaging among female youth and the potential impact of "plain" cigarette packaging regulations. A national sample of 947 16- to 19-year-old female subjects in the United Kingdom completed an online survey. Participants were randomized to view 10 cigarette packs designed according to one of four experimental conditions: fully branded female packs, the same packs without descriptor words, the same packs without brand imagery or descriptors ("plain" packs), and branded non-female brands. Participants rated packs on measures of appeal and health risk, positive smoker image, and completed a behavioral pack selection task. Plain packs were rated as the least appealing and worse tasting compared with all other conditions. Plain packs were also associated with fewer false beliefs about health risks compared with branded packs. Removing brand descriptors from packs significantly reduced measures of appeal and taste, particularly for brands with flavor descriptors, such as cherry and vanilla. Plain packs were significantly less likely to be associated with positive images, such as glamour, sophistication, and slimness. Most importantly, respondents were significantly less likely to accept a pack of cigarettes when offered only plain versus branded packs (p = .026). Marketing in the form of pack branding remains a potent tool for increasing the appeal of tobacco products to young women. The findings provide empirical support for plain cigarette packaging regulations in Australia to be implemented in 2012. Copyright © 2013 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Reliability of measured data for pH sensor arrays with fault diagnosis and data fusion based on LabVIEW.

Science.gov (United States)

Liao, Yi-Hung; Chou, Jung-Chuan; Lin, Chin-Yi

2013-12-13

Fault diagnosis (FD) and data fusion (DF) technologies implemented in the LabVIEW program were used for a ruthenium dioxide pH sensor array. The purpose of the fault diagnosis and data fusion technologies is to increase the reliability of measured data. Data fusion is a very useful statistical method used for sensor arrays in many fields. Fault diagnosis is used to avoid sensor faults and to measure errors in the electrochemical measurement system, therefore, in this study, we use fault diagnosis to remove any faulty sensors in advance, and then proceed with data fusion in the sensor array. The average, self-adaptive and coefficient of variance data fusion methods are used in this study. The pH electrode is fabricated with ruthenium dioxide (RuO2) sensing membrane using a sputtering system to deposit it onto a silicon substrate, and eight RuO2 pH electrodes are fabricated to form a sensor array for this study.

Reliability of Measured Data for pH Sensor Arrays with Fault Diagnosis and Data Fusion Based on LabVIEW

Directory of Open Access Journals (Sweden)

Yi-Hung Liao

2013-12-01

Full Text Available Fault diagnosis (FD and data fusion (DF technologies implemented in the LabVIEW program were used for a ruthenium dioxide pH sensor array. The purpose of the fault diagnosis and data fusion technologies is to increase the reliability of measured data. Data fusion is a very useful statistical method used for sensor arrays in many fields. Fault diagnosis is used to avoid sensor faults and to measure errors in the electrochemical measurement system, therefore, in this study, we use fault diagnosis to remove any faulty sensors in advance, and then proceed with data fusion in the sensor array. The average, self-adaptive and coefficient of variance data fusion methods are used in this study. The pH electrode is fabricated with ruthenium dioxide (RuO2 sensing membrane using a sputtering system to deposit it onto a silicon substrate, and eight RuO2 pH electrodes are fabricated to form a sensor array for this study.

Structural Characteristics of Nocturnal Mesoscale Convective Systems in the U.S. Great Plains as Observed During the PECAN Field Campaign

Science.gov (United States)

Bodine, D. J.; Dougherty, E.; Rasmussen, K. L.; Torres, A. D.

2015-12-01

During the summer in the U.S. Great Plains, some of the heaviest precipitation falls from large thunderstorm complexes known as Mesoscale Convective Systems (MCSs). These frequently occurring MCSs are often nocturnal in nature, so the dynamics associated with these systems are more elusive than those in the daytime. The Plains Elevated Convection at Night (PECAN) field campaign was launched over a 7-week period as an endeavor to better understand nocturnal MCSs occurring in the Great Plains. PECAN featured a dense array of ground-based and airborne instruments to observe nocturnal MCS, including dual-polarization radars at multiple frequencies, mobile mesonets, and sounding units. Our role in PECAN involved deploying Ott Parsivel disdrometers to gain information on drop size distributions (DSDs) and fall speeds. Analysis of disdrometer data in conjunction with radar data presented using Contour Frequency by Altitude Diagrams (CFADs) and high-resolution radiosonde data allows for a structural comparison of PECAN MCS cases to previously identified MCS archetypes. Novel insights into the structural evolution of nocturnal MCSs in relation to their synoptic, mesoscale, and thermodynamic environments are presented, using data collected from dense and numerous observation platforms. Understanding the environmental conditions that result in different nocturnal MCS configurations is useful for gaining insight into precipitation distributions and potential severe weather and flooding hazards in the Great Plains.

137Cs contamination of Techa river flood plain in Brodokalmak settlement

International Nuclear Information System (INIS)

Chesnokov, A.V.; Govorun, A.P.; Liksonov, V.I.; Shcherbak, S.B.; Ivanitskaya, M.V.

1999-01-01

137 Cs contamination of the Techa river flood plain inside the Brodokalmak settlement has been mapped. The collimated scintillated detector technique was used for 137 Cs deposit measurements. The 137 Cs contamination is very heterogeneous. A comparison of this technique with the traditional sample method was performed at selected locations. The sampling data are in good agreement with in-situ data. Soil surface activity of 90 Sr was determined from the samples. It was shown that 137 Cs contamination correlates with 90 Sr contamination within the flood plain of the settlement

A Multi-Functional Microelectrode Array Featuring 59760 Electrodes, 2048 Electrophysiology Channels, Stimulation, Impedance Measurement and Neurotransmitter Detection Channels.

Science.gov (United States)

Dragas, Jelena; Viswam, Vijay; Shadmani, Amir; Chen, Yihui; Bounik, Raziyeh; Stettler, Alexander; Radivojevic, Milos; Geissler, Sydney; Obien, Marie; Müller, Jan; Hierlemann, Andreas

2017-06-01

Biological cells are characterized by highly complex phenomena and processes that are, to a great extent, interdependent. To gain detailed insights, devices designed to study cellular phenomena need to enable tracking and manipulation of multiple cell parameters in parallel; they have to provide high signal quality and high spatiotemporal resolution. To this end, we have developed a CMOS-based microelectrode array system that integrates six measurement and stimulation functions, the largest number to date. Moreover, the system features the largest active electrode array area to date (4.48×2.43 mm 2 ) to accommodate 59,760 electrodes, while its power consumption, noise characteristics, and spatial resolution (13.5 μm electrode pitch) are comparable to the best state-of-the-art devices. The system includes: 2,048 action-potential (AP, bandwidth: 300 Hz to 10 kHz) recording units, 32 local-field-potential (LFP, bandwidth: 1 Hz to 300 Hz) recording units, 32 current recording units, 32 impedance measurement units, and 28 neurotransmitter detection units, in addition to the 16 dual-mode voltage-only or current/voltage-controlled stimulation units. The electrode array architecture is based on a switch matrix, which allows for connecting any measurement/stimulation unit to any electrode in the array and for performing different measurement/stimulation functions in parallel.

Environmental assessment for the Atmospheric Radiation Measurement (ARM) Program: Southern Great Plains Cloud and Radiation Testbed (CART) site

International Nuclear Information System (INIS)

Policastro, A.J.; Pfingston, J.M.; Maloney, D.M.; Wasmer, F.; Pentecost, E.D.

1992-03-01

The Atmospheric Radiation Measurement (ARM) Program is aimed at supplying improved predictive capability of climate change, particularly the prediction of cloud-climate feedback. The objective will be achieved by measuring the atmospheric radiation and physical and meteorological quantities that control solar radiation in the earth's atmosphere and using this information to test global climate and related models. The proposed action is to construct and operate a Cloud and Radiation Testbed (CART) research site in the southern Great Plains as part of the Department of Energy's Atmospheric Radiation Measurement Program whose objective is to develop an improved predictive capability of global climate change. The purpose of this CART research site in southern Kansas and northern Oklahoma would be to collect meteorological and other scientific information to better characterize the processes controlling radiation transfer on a global scale. Impacts which could result from this facility are described

Environmental assessment for the Atmospheric Radiation Measurement (ARM) Program: Southern Great Plains Cloud and Radiation Testbed (CART) site

Energy Technology Data Exchange (ETDEWEB)

Policastro, A.J.; Pfingston, J.M.; Maloney, D.M.; Wasmer, F.; Pentecost, E.D.

1992-03-01

The Atmospheric Radiation Measurement (ARM) Program is aimed at supplying improved predictive capability of climate change, particularly the prediction of cloud-climate feedback. The objective will be achieved by measuring the atmospheric radiation and physical and meteorological quantities that control solar radiation in the earth`s atmosphere and using this information to test global climate and related models. The proposed action is to construct and operate a Cloud and Radiation Testbed (CART) research site in the southern Great Plains as part of the Department of Energy`s Atmospheric Radiation Measurement Program whose objective is to develop an improved predictive capability of global climate change. The purpose of this CART research site in southern Kansas and northern Oklahoma would be to collect meteorological and other scientific information to better characterize the processes controlling radiation transfer on a global scale. Impacts which could result from this facility are described.

TiO2 nanocrystals decorated Z-schemed core-shell CdS-CdO nanorod arrays as high efficiency anodes for photoelectrochemical hydrogen generation.

Science.gov (United States)

Li, Chia-Hsun; Hsu, Chan-Wei; Lu, Shih-Yuan

2018-07-01

TiO 2 nanocrystals decorated core-shell CdS-CdO nanorod arrays, TiO 2 @CdO/CdS NR, were fabricated as high efficiency anodes for photoelctrochemical hydrogen generation. The novel sandwich heterostructure was constructed from first growth of CdS nanorod arrays on a fluorine doped tin oxide (FTO) substrate with a hydrothermal process, followed by in situ generation of CdO thin films of single digit nanometers from the CdS nanorod surfaces through thermal oxidation, and final decoration of TiO 2 nanocrystals of 10-20 nm via a successive ionic layer absorption and reaction process. The core-shell CdS-CdO heterostructure possesses a Z-scheme band structure to enhance interfacial charge transfer, facilitating effective charge separation to suppress electron-hole recombination within CdS for much improved current density generation. The final decoration of TiO 2 nanocrystals passivates surface defects and trap states of CdO, further suppressing surface charge recombination for even higher photovoltaic conversion efficiencies. The photoelectrochemical performances of the plain CdS nanorod array were significantly improved with the formation of the sandwich heterostructure, achieving a photo current density of 3.2 mA/cm 2 at 1.23 V (vs. RHE), a 141% improvement over the plain CdS nanorod array and a 32% improvement over the CdO/CdS nanorod array. Copyright © 2018 Elsevier Inc. All rights reserved.

Stability Measurements for Alignment of the NIF Neutron Imaging System Pinhole Array

International Nuclear Information System (INIS)

Fittinghoff, D.N.; Bower, D.E.; Drury, O.B.; Dzenitis, J.M.; Frank, M.; Buckles, R.A.; Munson, C.; Wilde, C.H.

2011-01-01

The alignment system for the National Ignition Facility's neutron imaging system has been commissioned and measurements of the relative stability of the 90-315 DIM, the front and the back of the neutron imaging pinhole array and an exploding pusher target have been made using the 90-135 and the 90-258 opposite port alignment systems. Additionally, a laser beam shot from the neutron-imaging Annex and reflected from a mirror at the back of the pinhole array was used to monitor the pointing of the pinhole. Over a twelve hour period, the relative stability of these parts was found to be within ∼ ±18 (micro)m rms even when using manual methods for tracking the position of the objects. For highly visible features, use of basic particle tracking techniques found that the front of the pinhole array was stable relative to the 90-135 opposite port alignment camera to within ±3.4 (micro)m rms. Reregistration, however, of the opposite port alignment systems themselves using the target alignment sensor was found to change the expected position of target chamber center by up to 194 (micro)m.

A Comparison of Plain Radiography with Computer Tomography in Determining Coronal and Sagittal Alignments following Total Knee Arthroplasty

Directory of Open Access Journals (Sweden)

Solayar GN

2017-07-01

Full Text Available INTRODUCTION: Optimal coronal and sagittal component positioning is important in achieving a successful outcome following total knee arthroplasty (TKA. Modalities to determine post-operative alignment include plain radiography and computer tomography (CT imaging. This study aims to determine the accuracy and reliability of plain radiographs in measuring coronal and sagittal alignment following TKA. MATERIALS AND METHODS: A prospective, consecutive study of 58 patients undergoing TKA was performed comparing alignment data from plain radiographs and CT imaging. Hip- knee-angle (HKA, sagittal femoral angle (SFA and sagittal tibial angle (STA measurements were taken by two observers from plain radiographs and compared with CT alignment. Intra- and inter-observer correlation was calculated for each measurement. RESULTS: Intra-observer correlation was excellent for HKA (r>0.89 with a mean difference of 0.95 and STA (r>0.8 compared to SFA (r=0.5. When comparing modalities (radiographs vs CT, HKA estimations for both observers showed the least maximum and mean differences while SFA observations were the least accurate. CONCLUSION: Radiographic estimation of HKA showed excellent intra- and inter-observer correlation and corresponds well with CT imaging. However, radiographic estimation of sagittal plane alignment was less reliably measured and correlated less with CT imaging. Plain radiography was found to be inferior to CT for estimation of biplanar prosthetic alignment following TKA.

Limitations of quantitative bone-mass measurements using assessments of first-order statistics of grey-level histograms in plain radiographs

Energy Technology Data Exchange (ETDEWEB)

Kouloulias, V.E.; Matsopoulos, G.; Kouvaris, J.R.; Antypas, C.; Uzunoglu, N.C.; Varela, M.N.; Metafa, A.; Sandilos, P.; Vlahos, L.J. [Areteion Univ. Hospital, Athens (Greece). Radiology Dept.

2004-04-01

PURPOSE: To evaluate the quality assurance of image-processing techniques in plain radiographs of skeletal structures. MATERIAL AND METHODS: Twenty-two patients were studied, each with one osteolytic metastasis. Accuracy and precision of tube voltage and timer were confirmed. The mean value of grey-level histograms in plain radiographs (MVGLHs) was assessed. The deviation was monitored after five sets of sequential X-rays retaining the same settings for each radiograph. RESULTS: Deviation was significantly higher in anatomical areas of thorax (21.2%) and abdomen (42.4%), while the consistency of MVGLH for weight-bearing bones was satisfactory with a maximum deviation of 2.9% (P<0.001, Kruskal-Wallis test). CONCLUSION: Assessment of MVGLH in plain radiographs is a reliable method for the extremities and generally for regions without superimposed movable tissues.

Limitations of quantitative bone-mass measurements using assessments of first-order statistics of grey-level histograms in plain radiographs

International Nuclear Information System (INIS)

Kouloulias, V.E.; Matsopoulos, G.; Kouvaris, J.R.; Antypas, C.; Uzunoglu, N.C.; Varela, M.N.; Metafa, A.; Sandilos, P.; Vlahos, L.J.

2004-01-01

PURPOSE: To evaluate the quality assurance of image-processing techniques in plain radiographs of skeletal structures. MATERIAL AND METHODS: Twenty-two patients were studied, each with one osteolytic metastasis. Accuracy and precision of tube voltage and timer were confirmed. The mean value of grey-level histograms in plain radiographs (MVGLHs) was assessed. The deviation was monitored after five sets of sequential X-rays retaining the same settings for each radiograph. RESULTS: Deviation was significantly higher in anatomical areas of thorax (21.2%) and abdomen (42.4%), while the consistency of MVGLH for weight-bearing bones was satisfactory with a maximum deviation of 2.9% (P<0.001, Kruskal-Wallis test). CONCLUSION: Assessment of MVGLH in plain radiographs is a reliable method for the extremities and generally for regions without superimposed movable tissues

Reliability of Measured Data for pH Sensor Arrays with Fault Diagnosis and Data Fusion Based on LabVIEW

OpenAIRE

Liao, Yi-Hung; Chou, Jung-Chuan; Lin, Chin-Yi

2013-01-01

Fault diagnosis (FD) and data fusion (DF) technologies implemented in the LabVIEW program were used for a ruthenium dioxide pH sensor array. The purpose of the fault diagnosis and data fusion technologies is to increase the reliability of measured data. Data fusion is a very useful statistical method used for sensor arrays in many fields. Fault diagnosis is used to avoid sensor faults and to measure errors in the electrochemical measurement system, therefore, in this study, we use fault diagn...

Development of an underground HPGe array facility for ultra low radioactivity measurements

Energy Technology Data Exchange (ETDEWEB)

Sala, E.; Kang, W. G.; Kim, Y. D.; Lee, M. H.; Leonard, D. S. [Center for Underground Physics - Institute for Basic Science, Daejeon (Korea, Republic of); Hahn, I. S.; Kim, G. W.; Park, S. Y. [Ewha Womans University, Physics Department, Seoul (Korea, Republic of)

2015-08-17

Low Level Counting techniques using low background facilities are continuously under development to increase the possible sensitivity needed for rare physics events experiments. The CUP (Center for Underground Physics) group of IBS is developing, in collaboration with Canberra, a ultra low background instrument composed of two arrays facing each other with 7 HPGe detectors each. The low radioactive background of each detector has been evaluated and improved by the material selection of the detector components. Samples of all the building materials have been provided by the manufacturer and the contaminations had been measured using an optimized low background 100% HPGe with a dedicated shielding. The evaluation of the intrinsic background has been performed using MonteCarlo simulations and considering the contribution of each material with the measured contamination. To further reduce the background, the instrument will be placed in the new underground laboratory at YangYang exploiting the 700m mountain coverage and radon-free air supplying system. The array has been designed to perform various Ultra Low background measurements; the sensitivity we are expecting will allow not only low level measurements of Ra and Th contaminations in Copper or other usually pure materials, but also the search for rare decays. In particular some possible candidates and configurations to detect the 0νECEC (for example {sup 106}Cd and {sup 156}Dy) and rare β decays ({sup 96}Zr, {sup 180m}Ta , etc ) are under study.

49 CFR 215.113 - Defective plain bearing wedge.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective plain bearing wedge. 215.113 Section 215... Suspension System § 215.113 Defective plain bearing wedge. A railroad may not place or continue in service a car, if a plain bearing wedge on that car is— (a) Missing; (b) Cracked; (c) Broken; or (d) Not located...

Characterization of photovoltaic array performance: an overview

Energy Technology Data Exchange (ETDEWEB)

Ross, Jr., R. G.

1986-09-15

Characterization of the electrical performance of a photovoltaic array can take many forms depending on the end use of the data. Typical uses include buyer-seller negotiations, system performance prediction, and performance measurement. Buyer-seller negotiations may deal with specifying the size (power) of an array to be purchased under some standard reporting conditions, and may treat the warranty conditions governing allowable degradation of this performance with time. System design, on the other hand, requires prediction of performance under varying field conditions, not standard reporting conditions, and must include the non-ideal realities of operating systems: array shadowing, steep angles of incidence, soiling, and array-load energy utilization. Typical uses of predicted array performance include array sizing tradeoffs, tracking-pointing comparisons, load-array interface analyses and system economic evaluations. The third use, performance measurement, refers to the characterization of an as-built array as opposed to prediction of the performance of an array to be built. This may be done to assess actual array performance or to measure performance degradation over time.

Circular Array of Magnetic Sensors for Current Measurement: Analysis for Error Caused by Position of Conductor.

Science.gov (United States)

Yu, Hao; Qian, Zheng; Liu, Huayi; Qu, Jiaqi

2018-02-14

This paper analyzes the measurement error, caused by the position of the current-carrying conductor, of a circular array of magnetic sensors for current measurement. The circular array of magnetic sensors is an effective approach for AC or DC non-contact measurement, as it is low-cost, light-weight, has a large linear range, wide bandwidth, and low noise. Especially, it has been claimed that such structure has excellent reduction ability for errors caused by the position of the current-carrying conductor, crosstalk current interference, shape of the conduction cross-section, and the Earth's magnetic field. However, the positions of the current-carrying conductor-including un-centeredness and un-perpendicularity-have not been analyzed in detail until now. In this paper, for the purpose of having minimum measurement error, a theoretical analysis has been proposed based on vector inner and exterior product. In the presented mathematical model of relative error, the un-center offset distance, the un-perpendicular angle, the radius of the circle, and the number of magnetic sensors are expressed in one equation. The comparison of the relative error caused by the position of the current-carrying conductor between four and eight sensors is conducted. Tunnel magnetoresistance (TMR) sensors are used in the experimental prototype to verify the mathematical model. The analysis results can be the reference to design the details of the circular array of magnetic sensors for current measurement in practical situations.

Micromachined microphone array on a chip for turbulent boundary layer measurements

Science.gov (United States)

Krause, Joshua Steven

A surface micromachined microphone array on a single chip has been successfully designed, fabricated, characterized, and tested for aeroacoustic purposes. The microphone was designed to have venting through the diaphragm, 64 elements (8x8) on the chip, and used a capacitive transduction scheme. The microphone was fabricated using the MEMSCAP PolyMUMPs process (a foundry polysilicon surface micromachining process) along with facilities at Tufts Micro and Nano Fabrication Facility (TMNF) where a Parylene-C passivation layer deposition and release of the microstructures were performed. The devices are packaged with low profile interconnects, presenting a maximum of 100 mum of surface topology. The design of an individual microphone was completed through the use of a lumped element model (LEM) to determine the theoretical performance of the microphone. Off-chip electronics were created to allow the microphone array outputs to be redirected to one of two channels, allowing dynamic reconfiguration of the effective transducer shape in software and provide 80 dB off isolation. The characterization was completed through the use of laser Doppler vibrometry (LDV), acoustic plane wave tube and free-field calibration, and electrical noise floor testing in a Faraday cage. Measured microphone sensitivity is 0.15 mV/Pa for an individual microphone and 8.7 mV/Pa for the entire array, in close agreement with model predictions. The microphones and electronics operate over the 200--40 000 Hz band. The dynamic range extends from 60 dB SPL in a 1 Hz band to greater than 150 dB SPL. Element variability was +/-0.05 mV/Pa in sensitivity with an array yield of 95%. Wind tunnel testing at flow rates of up to 205.8 m/s indicates that the devices continue to operate in flow without damage, and can be successfully reconfigured on the fly. Care has been taken to systematically remove contaminating signals (acoustic, vibration, and noise floor) from the wind tunnel data to determine actual

Mars Array Technology Experiment Developed to Test Solar Arrays on Mars

Science.gov (United States)

Landis, Geoffrey A.

2001-01-01

Solar arrays will be the power supply for future missions to the planet Mars, including landers, rovers, and eventually human missions to explore the Martian surface. Until Mars Pathfinder landed in July 1997, no solar array had been used on the surface. The MATE package is intended to measure the solar energy reaching the surface, characterize the Martian environment to gather the baseline information required for designing power systems for long-duration missions, and to quantify the performance and degradation of advanced solar cells on the Martian surface. To measure the properties of sunlight reaching the Martian surface, MATE incorporates two radiometers and a visible/NIR spectrometer. The radiometers consist of multiple thermocouple junctions using thin-film technology. These devices generate a voltage proportional to the solar intensity. One radiometer measures the global broadband solar intensity, including both the direct and scattered sunlight, with a field of view of approximately 130. The second radiometer incorporates a slit to measure the direct (unscattered) intensity radiation. The direct radiometer can only be read once per day, with the Sun passing over the slit. The spectrometer measures the global solar spectrum with two 256-element photodiode arrays, one Si sensitive in the visible range (300 to 1100 nm), and a second InGaAs sensitive to the near infrared (900 to 1700 nm). This range covers 86 percent of the total energy from the Sun, with approximately 5-nm resolution. Each photodiode array has its own fiber-optic feed and grating. Although the purpose of the MATE is to gather data useful in designing solar arrays for Mars surface power systems, the radiometer and spectrometer measurements are expected to also provide important scientific data for characterizing the properties of suspended atmospheric dust. In addition to measuring the solar environment of Mars, MATE will measure the performance of five different individual solar cell types

Monitoring interseismic activity on the Ilan Plain (NE Taiwan) using Small Baseline PS-InSAR, GPS and leveling measurements: partitioning from arc-continent collision and backarc extension

Science.gov (United States)

Su, Zhe; Hu, Jyr-Ching; Wang, Erchie; Li, Yongsheng; Yang, Yinghui; Wang, Pei-Ling

2018-01-01

The Ilan Plain, located in Northeast Taiwan, represents a transition zone between oblique collision (between the Luzon Arc and the Eurasian Plate) and backarc extension (the Okinawa Trough). The mechanism for this abrupt transition from arc-continent collision to backarc extension remains uncertain. We used Global Positioning System (GPS), leveling and multi-interferogram Small Baseline Persistent Scatterer Interferometry (SBAS-PSI) data to monitor the interseismic activity in the basin. A common reference site was selected for the data sets. The horizontal component of GPS and the vertical measurements of the leveling data were converted to line-of-sight (LOS) data and compared with the SBAS-PSI data. The comparison shows that the entire Ilan Plain is undergoing rapid subsidence at a maximum rate of -11 ± 2 mm yr-1 in the LOS direction. We speculate that vertical deformation and anthropogenic activity may play important roles in this deformation. We also performed a joint inversion modeling that combined both the DInSAR and strong motion data to constrain the source model of the 2005 Ilan earthquake. The best-fitting model predicts that the Sansing fault caused the 2005 Ilan earthquake. The observed transtensional deformation is dominated by the normal faulting with a minor left-lateral strike-slip motion. We compared our SBAS-PSI results with the short-term (2005-2009) groundwater level changes. The results indicate that although pumping-induced surface subsidence cannot be excluded, tectonic deformation, including rapid southward movement of the Ryukyu arc and backarc extension of the Okinawa Trough, characterizes the opening of the Ilan Plain. Furthermore, a series of normal and left-lateral strike-slip transtensional faults, including the Choshui and Sansing faults, form a bookshelf-like structure that accommodates the extension of the plain. Although situated in a region of complex structural interactions, the Ilan Plain is primarily controlled by extension

Standard heart and vessel size on plain films of normal children

International Nuclear Information System (INIS)

Stoever, B.

1986-01-01

Standards of heart size, i.e. heart diameters and heart volume of normal children aged 4-15 years were obtained. In all cases requiring exact heart size determination, heart volume calculation is mandatory in children as well as in adults. Statistical work to date has provided precise calculation of heart volume plain films in the upright position. Additional plain films in prone position are unnecessary because no evident orthostatic influence on heart volume in children can be found. Percentiles of normal heart volume related to body weight representing the best correlation to the individual data are given as well as percentiles related to age. Furthermore ratios of normal vessel size to the height of the 8sup(th) thoracic vertebral body, measured on the same plain film, are given. In addition the ratio of upper to lower lung vessel size is calculated. These ratios are useful criteria in estimating normal vessel size and also in cases with increased pulmonary venous pressure. (orig.) [de

Ultrasound pulse-echo measurements on rough surfaces with linear array transducers

DEFF Research Database (Denmark)

Sjøj, Sidsel M. N.; Blanco, Esther N.; Wilhjelm, Jens E.

2012-01-01

The echo from planar surfaces with rms roughness, Rq, in the range from 0-155 μm was measured with a clinical linear array transducer at different angles of incidence at 6 MHz and 12 MHz. The echo-pulse from the surfaces was isolated with an equal sized window and the power of the echo-pulse was ......The echo from planar surfaces with rms roughness, Rq, in the range from 0-155 μm was measured with a clinical linear array transducer at different angles of incidence at 6 MHz and 12 MHz. The echo-pulse from the surfaces was isolated with an equal sized window and the power of the echo......-pulse was calculated. The power of the echo from the smooth surface (Rq = 0) is highly angle-dependent due to a high degree of specular reflection. Within the angular range considered here, -10° to 10°, the variation spans a range of 18 dB at both 6 MHz and 12 MHz. When roughness increases, the angle......-dependence decreases, as the echo process gradually changes from pure reflection to being predominantly governed by backscattering. The power of the echoes from the two roughest surfaces (Rq = 115 μm and 155 μm) are largely independent of angle at both 6 MHz and 12 MHz with a variation of 2 dB in the angular range...

Development of a Tonometric Sensor with a Decoupled Circular Array for Precisely Measuring Radial Artery Pulse

OpenAIRE

Jun, Min-Ho; Kim, Young-Min; Bae, Jang-Han; Jung, Chang Jin; Cho, Jung-Hee; Jeon, Young Ju

2016-01-01

The radial artery pulse is one of the major diagnostic indices used clinically in both Eastern and Western medicine. One of the prominent methods for measuring the radial artery pulse is the piezoresistive sensor array. Independence among channels and an appropriate sensor arrangement are important for effectively assessing the spatial-temporal information of the pulse. This study developed a circular-type seven-channel piezoresistive sensor array using face-down bonding (FDB) as one of the s...

Occurrence and variability of mining-related lead and zinc in the Spring River flood plain and tributary flood plains, Cherokee County, Kansas, 2009--11

Science.gov (United States)

Juracek, Kyle E.

2013-01-01

, Cow Creek, and Shawnee Creek—generally had flood-plain lead and zinc concentrations (surficial soil, 6- and 12-inch depth) that were substantially less than the general PECs. Tributaries with extensive lead- and zinc-mined areas in the basin—Shoal Creek, Short Creek, Spring Branch, Tar Creek, Turkey Creek, and Willow Creek—had flood-plain lead concentrations (surficial soil, 6- and 12-inch depth) that frequently or typically exceeded the general and TSMD-specific PECs. Likewise, the tributaries with extensive lead- and zinc-mined areas in the basin had flood-plain zinc concentrations (surficial soil, 6- and 12-inch depth) that frequently or typically exceeded the general PEC. With the exception of Shoal and Willow Creeks, zinc concentrations typically exceeded the TSMD-specific PEC. The largest flood-plain lead and zinc concentrations (surficial soil, 6- and 12-inch depth) were measured for Short and Tar Creeks. Lead and zinc concentrations in the surficial-soil samples collected from the tributary flood plains varied longitudinally in relation to sources of mining-contaminated sediment in the basins. Lead and zinc concentrations also varied with distance from the channel; however, no consistent spatial trend was evident. For the surficial-soil samples collected from the Spring River flood plain and tributary flood plains, both the coarse (larger than 63 micrometers) and fine particles (less than 63 micrometers) contained substantial lead and zinc concentrations.

Shear wave velocities in the upper mantle of the Western Alps: new constraints using array analysis of seismic surface waves

Science.gov (United States)

Lyu, Chao; Pedersen, Helle A.; Paul, Anne; Zhao, Liang; Solarino, Stefano

2017-07-01

It remains challenging to obtain absolute shear wave velocities of heterogeneities of small lateral extension in the uppermost mantle. This study presents a cross-section of Vs across the strongly heterogeneous 3-D structure of the western European Alps, based on array analysis of data from 92 broad-band seismic stations from the CIFALPS experiment and from permanent networks in France and Italy. Half of the stations were located along a dense sublinear array. Using a combination of these stations and off-profile stations, fundamental-mode Rayleigh wave dispersion curves were calculated using a combined frequency-time beamforming approach. We calculated dispersion curves for seven arrays of approximately 100 km aperture and 14 arrays of approximately 50 km aperture, the latter with the aim of obtaining a 2-D vertical cross-section of Vs beneath the western Alps. The dispersion curves were inverted for Vs(z), with crustal interfaces imposed from a previous receiver function study. The array approach proved feasible, as Vs(z) from independent arrays vary smoothly across the profile length. Results from the seven large arrays show that the shear velocity of the upper mantle beneath the European plate is overall low compared to AK135 with the lowest velocities in the internal part of the western Alps, and higher velocities east of the Alps beneath the Po plain. The 2-D Vs model is coherent with (i) a ∼100 km thick eastward-dipping European lithosphere west of the Alps, (ii) very high velocities beneath the Po plain, coherent with the presence of the Alpine (European) slab and (iii) a narrow low-velocity anomaly beneath the core of the western Alps (from the Briançonnais to the Dora Maira massif), and approximately colocated with a similar anomaly observed in a recent teleseismic P-wave tomography. This intriguing anomaly is also supported by traveltime variations of subvertically propagating body waves from two teleseismic events that are approximately located on

Preparation of Janus Particles and Alternating Current Electrokinetic Measurements with a Rapidly Fabricated Indium Tin Oxide Electrode Array.

Science.gov (United States)

Chen, Yu-Liang; Jiang, Hong-Ren

2017-06-23

This article provides a simple method to prepare partially or fully coated metallic particles and to perform the rapid fabrication of electrode arrays, which can facilitate electrical experiments in microfluidic devices. Janus particles are asymmetric particles that contain two different surface properties on their two sides. To prepare Janus particles, a monolayer of silica particles is prepared by a drying process. Gold (Au) is deposited on one side of each particle using a sputtering device. The fully coated metallic particles are completed after the second coating process. To analyze the electrical surface properties of Janus particles, alternating current (AC) electrokinetic measurements, such as dielectrophoresis (DEP) and electrorotation (EROT)- which require specifically designed electrode arrays in the experimental device- are performed. However, traditional methods to fabricate electrode arrays, such as the photolithographic technique, require a series of complicated procedures. Here, we introduce a flexible method to fabricate a designed electrode array. An indium tin oxide (ITO) glass is patterned by a fiber laser marking machine (1,064 nm, 20 W, 90 to 120 ns pulse-width, and 20 to 80 kHz pulse repetition frequency) to create a four-phase electrode array. To generate the four-phase electric field, the electrodes are connected to a 2-channel function generator and to two invertors. The phase shift between the adjacent electrodes is set at either 90° (for EROT) or 180° (for DEP). Representative results of AC electrokinetic measurements with a four-phase ITO electrode array are presented.

"Plain packaging" regulations for tobacco products: the impact of standardizing the color and design of cigarette packs.

Science.gov (United States)

Hammond, David

2010-01-01

Tobacco packaging and labeling policies have emerged as prominent and cost-effective tobacco control measures. Although packaging policies have primarily focused on health warnings, there is growing recognition of the importance of packaging as a marketing tool for the tobacco industry. The current paper reviews evidence on the potential impact of standardizing the color and design of tobacco packages -so called "plain" packaging. The evidence indicates three primary benefits of plain packaging: increasing the effectiveness of health warnings, reducing false health beliefs about cigarettes, and reducing brand appeal especially among youth and young adults. Overall, the research to date suggests that "plain" packaging regulations would be an effective tobacco control measure, particularly in jurisdictions with comprehensive restrictions on other forms of marketing.

An optode sensor array for long term in situ Oxygen measurements in soil and sediment

DEFF Research Database (Denmark)

Rickelt, Lars F; Jensen, Louise Askær; Walpersdorf, Eva Christine

2013-01-01

Long-term measurements of molecular oxygen (O2) dynamics in wetlands are highly relevant for understanding the eff ects of water level changes on net greenhouse gas budgets in these ecosystems. However, such measurements have been limited due to a lack of suitable measuring equipment. We construc......Long-term measurements of molecular oxygen (O2) dynamics in wetlands are highly relevant for understanding the eff ects of water level changes on net greenhouse gas budgets in these ecosystems. However, such measurements have been limited due to a lack of suitable measuring equipment. We...... constructed an O2 optode sensor array for long-term in situ measurements in soil and sediment. Th e new device consists of a 1.3-m-long, cylindrical, spear-shaped rod equipped with 10 sensor spots along the shaft . Each spot contains a thermocouple fi xed with a robust fi beroptic O2 optode made...... characteristics of the sensor array system are presented along with a novel approach for temperature compensation of O2 optodes. During in situ application over several months in a peat bog, we used the new device to document pronounced variations in O2 distribution aft er marked shift s in water level. Th e...

S-Wave Velocity Structure of the Taiwan Chelungpu Fault Drilling Project (TCDP) Site Using Microtremor Array Measurements

Science.gov (United States)

Wu, Cheng-Feng; Huang, Huey-Chu

2015-10-01

The Taiwan Chelungpu Fault Drilling Project (TCDP) drilled a 2-km-deep hole 2.4 km east of the surface rupture of the 1999 Chi-Chi earthquake ( M w 7.6), near the town of Dakeng. Geophysical well logs at the TCDP site were run over depths ranging from 500 to 1,900 m to obtain the physical properties of the fault zones and adjacent damage zones. These data provide good reference material for examining the validity of velocity structures using microtremor array measurement; therefore, we conduct array measurements for a total of four arrays at two sites near the TCDP drilling sites. The phase velocities at frequencies of 0.2-5 Hz are calculated using the frequency-wavenumber ( f- k) spectrum method. Then the S-wave velocity structures are estimated by employing surface wave inversion techniques. The S-wave velocity from the differential inversion technique gradually increases from 1.52 to 2.22 km/s at depths between 585 and 1,710 m. This result is similar to those from the velocity logs, which range from 1.4 km/s at a depth of 597 m to 2.98 km/s at a depth of 1,705 m. The stochastic inversion results are similar to those from the seismic reflection methods and the lithostratigraphy of TCDP-A borehole, comparatively. These results show that microtremor array measurement provides a good tool for estimating deep S-wave velocity structure.

Measurement, characterization, and modeling of noise in staring infrared focal plane arrays

International Nuclear Information System (INIS)

Scribner, D.A.; Kruer, M.R.; Gridley, C.J.; Sarkady, K.

1987-01-01

An account is given of selected methods for the measurement and characterization of spatial and temporal noise in staring focal plane arrays (FPAs), in order to demonstrate how these results can be used in simulations and analytic models to predict the performance of selected staring sensors. Attention is given to MIR FPAs applicable to the detection and tracking of point sources, and to the ways in which these spatial and temporal noise measurements can be incorporated into simulations and sensors having staring FPAs. Methods for predicting the performance of selected staring sensor systems are derivable from spatial and temporal noise values. 13 references

Measurement of long-term land subsidence by combination of InSAR and time series analysis - Application study to Kanto Plains of Japan -

Science.gov (United States)

Deguchi, T.; Rokugawa, S.; Matsushima, J.

2009-04-01

InSAR is an application technique of synthetic aperture radars and is now drawing attention as a methodology capable of measuring subtle surface deformation over a wide area with a high spatial resolution. In this study, the authors applied the method of measuring long-term land subsidence by combining InSAR and time series analysis to Kanto Plains of Japan using 28 images of ENVISAT/ASAR data. In this measuring method, the value of land deformation is set as an unknown parameter and the optimal solution to the land deformation amount is derived by applying a smoothness-constrained inversion algorithm. The vicinity of the Kanto Plain started to subside in the 1910s, and became exposed to extreme land subsidence supposedly in accordance with the reconstruction efforts after the Second World War and the economic development activities. The main causes of the land subsidence include the intake of underground water for the use in industries, agriculture, waterworks, and other fields. In the Kujukuri area, the exploitation of soluble natural gas also counts. The Ministry of Environment reported in its documents created in fiscal 2006 that a total of 214 km2 in Tokyo and the six prefectures around the Plain had undergone a subsidence of 1 cm or more per a year. As a result of long-term land subsidence over approximately five and a half years from 13th January, 2003, to 30th June, 2008, unambiguous land deformation was detected in six areas: (i) Haneda Airport, (ii) Urayasu City, (iii) Kasukabe-Koshigaya, (iv) Southern Kanagawa, (v) Toride-Ryugasaki, and (vi) Kujukuri in Chiba Prefecture. In particular, the results for the Kujukuri area were compared with the leveling data taken around the same area to verify the measuring accuracy. The comparative study revealed that the regression formula between the results obtained by time series analysis and those by the leveling can be expressed as a straight line with a gradient of approximately 1, though including a bias of about

Measurement of the modulation transfer function of a charge-coupled device array by the combination of the self-imaging effect and slanted edge method.

Science.gov (United States)

Najafi, Sedigheh; Madanipour, Khosro

2013-07-01

In this paper, by a combination of the self-imaging effect for Ronchi gratings and the standard slanted edge modulation transfer function (MTF) measurement method for CCD cameras, the MTF of the CCD array without optics is measured. For this purpose, a Ronchi-type grating is illuminated by an expanded He-Ne laser. A self-image of the grating appears without optics on the CCD array that is located on the Talbot distance. The lines of the self-image of the grating are used as a slanted edge array. This method has all the advantages of the slanted edge method, and also since the array of the edge is ready, the total area of the CCD can be tested. The measured MTF is related to the CCD array without optics.

Behavior of Plain Concrete of a High Water-Cement Ratio after Freeze-Thaw Cycles

OpenAIRE

Shang, Huai-Shuai; Yi, Ting-Hua; Song, Yu-Pu

2012-01-01

An experimental study of plain concrete specimens of water-cement ratio 0.55, subjected to 0, 15, 25, 40, 50 and 75 cycles of freeze-thaw was completed. The dynamic modulus of elasticity (DME), weight loss, compressive strength, tensile strength, flexural strength, cleavage strength and stress-strain relationships of plain concrete specimens suffering from freeze-thaw cycles were measured. The experimental results showed that the strength decreased as the freeze-thaw cycles were repeated. A c...

Quantitative measurements of C-reactive protein using silicon nanowire arrays

Directory of Open Access Journals (Sweden)

Min-Ho Lee

2008-03-01

Full Text Available Min-Ho Lee, Kuk-Nyung Lee, Suk-Won Jung, Won-Hyo Kim, Kyu-Sik Shin, Woo-Kyeong SeongKorea Electronics Technology Institute, Gyeonggi, KoreaAbstract: A silicon nanowire-based sensor for biological application showed highly desirable electrical responses to either pH changes or receptor-ligand interactions such as protein disease markers, viruses, and DNA hybridization. Furthermore, because the silicon nanowire can display results in real-time, it may possess superior characteristics for biosensing than those demonstrated in previously studied methods. However, despite its promising potential and advantages, certain process-related limitations of the device, due to its size and material characteristics, need to be addressed. In this article, we suggest possible solutions. We fabricated silicon nanowire using a top-down and low cost micromachining method, and evaluate the sensing of molecules after transfer and surface modifications. Our newly designed method can be used to attach highly ordered nanowires to various substrates, to form a nanowire array device, which needs to follow a series of repetitive steps in conventional fabrication technology based on a vapor-liquid-solid (VLS method. For evaluation, we demonstrated that our newly fabricated silicon nanowire arrays could detect pH changes as well as streptavidin-biotin binding events. As well as the initial proof-of-principle studies, C-reactive protein binding was measured: electrical signals were changed in a linear fashion with the concentration (1 fM to 1 nM in PBS containing 1.37 mM of salts. Finally, to address the effects of Debye length, silicon nanowires coupled with antigen proteins underwent electrical signal changes as the salt concentration changed.Keywords: silicon nanowire array, C-reactive protein, vapor-liquid-solid method

Seismic echo character northern Hatteras Abyssal Plain

International Nuclear Information System (INIS)

McCreery, C.J.; Laine, E.P.

1985-01-01

Latest efforts in echo-character mapping of the northern Hatteras Abyssal Plain have discerned variations in thickness in a near-surface sedimentary sequence which has been designated seismic unit A. This unit probably represents the last episode of progradation of the Hatteras Deep Sea Fan in the southern part of the study area, and has infilled probable paleochannels from the Wilmington Canyon and Sohm Gap in the north. Unit A thins to a minimum in the central part of the plain, where older sediments come within 1 meter of the surface. Variations in the character of the surface reflector probably represent differing degrees of microtopography developed on a Late Pleistocene surface overlain by Holocene sediments. With the exception of one area identified as a relict surface outcropping in the western plain, this microtopography seems related to present-day thalweg locations on the abyssal plain. 11 references, 13 figures

Quantifying local-scale dust emission from the Arabian Red Sea coastal plain

KAUST Repository

Anisimov, Anatolii

2017-01-23

Dust plumes emitted from the narrow Arabian Red Sea coastal plain are often observed on satellite images and felt in local population centers. Despite its relatively small area, the coastal plain could be a significant dust source; however, its effect is not well quantified as it is not well approximated in global or even regional models. In addition, because of close proximity to the Red Sea, a significant amount of dust from the coastal areas could be deposited into the Red Sea and serve as a vital component of the nutrient balance of marine ecosystems. In the current study, we apply the offline Community Land Model version 4 (CLM4) to better quantify dust emission from the coastal plain during the period of 2009-2011. We verify the spatial and temporal variability in model results using independent weather station reports. We also compare the results with the MERRA Aerosol Reanalysis (MERRAero). We show that the best results are obtained with 1 km model spatial resolution and dust source function based on Meteosat Second Generation Spinning Enhanced Visible and InfraRed Imager (SEVIRI) measurements. We present the dust emission spatial pattern, as well as estimates of seasonal and diurnal variability in dust event frequency and intensity, and discuss the emission regime in the major dust generation hot spot areas. We demonstrate the contrasting seasonal dust cycles in the northern and southern parts of the coastal plain and discuss the physical mechanisms responsible for dust generation. This study provides the first estimates of the fine-scale spatial and temporal distribution of dust emissions from the Arabian Red Sea coastal plain constrained by MERRAero and short-term WRF-Chem simulations. The estimate of total dust emission from the coastal plain, tuned to fit emissions in MERRAero, is 7.5 ± 0.5 Mt a. Small interannual variability indicates that the study area is a stable dust source. The mineralogical composition analysis shows that the coastal plain

Quantifying local-scale dust emission from the Arabian Red Sea coastal plain

KAUST Repository

Anisimov, Anatolii; Tao, Weichun; Stenchikov, Georgiy L.; Kalenderski, Stoitchko; Jish Prakash, P.; Yang, Zong Liang; Shi, Mingjie

2017-01-01

Dust plumes emitted from the narrow Arabian Red Sea coastal plain are often observed on satellite images and felt in local population centers. Despite its relatively small area, the coastal plain could be a significant dust source; however, its effect is not well quantified as it is not well approximated in global or even regional models. In addition, because of close proximity to the Red Sea, a significant amount of dust from the coastal areas could be deposited into the Red Sea and serve as a vital component of the nutrient balance of marine ecosystems. In the current study, we apply the offline Community Land Model version 4 (CLM4) to better quantify dust emission from the coastal plain during the period of 2009-2011. We verify the spatial and temporal variability in model results using independent weather station reports. We also compare the results with the MERRA Aerosol Reanalysis (MERRAero). We show that the best results are obtained with 1 km model spatial resolution and dust source function based on Meteosat Second Generation Spinning Enhanced Visible and InfraRed Imager (SEVIRI) measurements. We present the dust emission spatial pattern, as well as estimates of seasonal and diurnal variability in dust event frequency and intensity, and discuss the emission regime in the major dust generation hot spot areas. We demonstrate the contrasting seasonal dust cycles in the northern and southern parts of the coastal plain and discuss the physical mechanisms responsible for dust generation. This study provides the first estimates of the fine-scale spatial and temporal distribution of dust emissions from the Arabian Red Sea coastal plain constrained by MERRAero and short-term WRF-Chem simulations. The estimate of total dust emission from the coastal plain, tuned to fit emissions in MERRAero, is 7.5 ± 0.5 Mt a. Small interannual variability indicates that the study area is a stable dust source. The mineralogical composition analysis shows that the coastal plain

Sources and flow of north Canterbury Plains groundwater, New Zealand

International Nuclear Information System (INIS)

Taylor, C.B.; Brown, L.J.; Stewart, M.K.; Brailsford, G.W.; Wilson, D.D.; Burden, R.J.

1989-01-01

Geological, hydrological, isotope (tritium and 18 O) and chemical evidence is interpreted to give a mutually consistent picture of the recharge sources and flow patterns of the important groundwater resource in the deep Quaternary deposits of the Canterbury Plains between Selwyn R. and Ashley R. The study period for tritium measurements extends over 27 years, encompassing the peak and decline of thermonuclear tritium fallout in this region. Major rivers emerging from mountain catchments to the west of the Plains are depleted in 18 O relative to average low-level precipitation. Most of the groundwater is river-recharged, but some areas with significant local precipitation recharge are clearly identified by 18 O and chemical concentrations. Artesian groundwater underlying Christchurch ascends from deeper aquifers into the shallowest aquifer via gaps in the confining layers; much of this flow is induced by withdrawal. The Christchurch aquifers are recharged by infiltration from Waimakariri R. in its central Plains reaches, and the resulting flow regime is E- and SE-directed; satisfactory water quality of the deeper Christchurch aquifer appears to be guaranteed for the future provided the river can be maintained in its present condition. Shallow groundwater, and water recharged to depth by other rivers, irrigation and local precipitation on the unconfined western areas of the Plains, are more susceptible to agricultural and other pollutants; none of this water is encountered in the deeper aquifers under Christchurch. (author). 15 refs., 12 figs

Measurement of the cosmic-ray energy spectrum above 1016 eV with the LOFAR Radboud Air Shower Array

NARCIS (Netherlands)

Thoudam, S.; Buitink, S.; Corstanje, A.; Enriquez, J. E.; Falcke, H.; Hörandel, J. R.; Nelles, A.; Rachen, J. P.; Rossetto, L.; Schellart, P.; Scholten, O.; ter Veen, S.; Trinh, T.N.G.; van Kessel, L.

2016-01-01

The energy reconstruction of extensive air showers measured with the LOFAR Radboud Air Shower Array (LORA) is presented in detail. LORA is a particle detector array located in the center of the LOFAR radio telescope in the Netherlands. The aim of this work is to provide an accurate and independent

Wind Shear Characteristics at Central Plains Tall Towers (presentation)

Energy Technology Data Exchange (ETDEWEB)

Schwartz, M.; Elliott, D.

2006-06-05

The objectives of this report are: (1) Analyze wind shear characteristics at tall tower sites for diverse areas in the central plains (Texas to North Dakota)--Turbines hub heights are now 70-100 m above ground and Wind measurements at 70-100+ m have been rare. (2) Present conclusions about wind shear characteristics for prime wind energy development regions.

49 CFR 230.102 - Tender plain bearing journal boxes.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Tender plain bearing journal boxes. 230.102... Locomotives and Tenders Running Gear § 230.102 Tender plain bearing journal boxes. Plain bearing journal boxes... expected to damage the bearing; or have a detrimental effect on the lubrication of the journal and bearing...

Heat flow measurements in the vicinity of Great Meteor East, Madeira Abyssal Plain, during Darwin Cruise CD9B

International Nuclear Information System (INIS)

Noel, M.; Hounslow, M.W.

1986-12-01

This report describes 37 new measurements of heat flow in the Madeira Abyssal Plain. These have comprised 22 values in the Great Meteor East Study Area and 15 measurements in the newly defined ''10 km Box'' to the southeast of this region. The aim of the project has been to examine in more detail than hitherto the thermal and fluid processes operating in the oceanic crust. For this purpose, a new thermistor string, with 1/2 m sensor spacing was used. Also, the heat flux data have been compared to the output from a finite element model for heat conduction. No non-linear sediment temperature profiles were discovered indicating that vertical advection of water through the sediment is absent or slow. The results of numerical modelling imply that the variability of measured heat flow cannot be explained entirely on the basis of basement topography. It is necessary to invoke either vertical basement intrusions of differing conductivity or basement hydrothermal circulation. (author)

Application of Faraday cup array detector in measurement of electron-beam distribution homogeneity

International Nuclear Information System (INIS)

Xu Zhiguo; Wang Jinchuan; Xiao Guoqing; Guo Zhongyan; Wu Lijie; Mao Ruishi; Zhang Li

2005-01-01

It is described that a kind of Faraday cup array detector, which consists of Faraday cup, suppressor electrode insulation PCB board, Base etc. The homogeneity of electron-beam distribution is measured and the absorbed dose for the irradiated sample is calculated. The results above provide the important parameters for the irradiation experiment and the improvement for the quality of electron beam. (authors)

Absence or interruption of the supra-acetabular line: a subtle plain film indicator of hip pathology

International Nuclear Information System (INIS)

Major, N.M.; Helms, C.A.

1996-01-01

Objective. To show that absence or interruption of the supraacetabular line is a subtle plain film indicator of pathology in the acetabulum. Design. Nineteen hips from 17 patients with known disease processes involving the acetabulum as demonstrated by subsequent magnetic resonance imaging, bone scan or plain film follow-up were evaluated with antero-posterior (AP) plain films of the pelvis. Three additional cases were diagnosed prospectively using interruption of the supra-acetabular line as the criterion for inclusion. Fifty AP plain films of the pelvis in patients without hip pain were examined prospectively to determine normal imaging criteria. Results and conclusions. The normal supra-acetabular line measures 2-3 mm in thickness superiorly and is a thin sclerotic line in the medial aspect. In all 22 hips (with pathology) in this series, the line was interrupted or absent. Loss or interruption of the supra-acetabular line may thus be a subtle pain film indicator of a disease process involving the acetabulum. This plain film sign has not previously been reported. (orig.). With 8 figs., 1 tab

The Great Plains IDEA Gerontology Program: An Online, Interinstitutional Graduate Degree

Science.gov (United States)

Sanders, Gregory F.

2011-01-01

The Great-Plains IDEA Gerontology Program is a graduate program developed and implemented by the Great Plains Interactive Distance Education Alliance (Great Plains IDEA). The Great Plains IDEA (Alliance) originated as a consortium of Colleges of Human Sciences ranging across the central United States. This Alliance's accomplishments have included…

Performance of A Compact Multi-crystal High-purity Germanium Detector Array for Measuring Coincident Gamma-ray Emissions

Energy Technology Data Exchange (ETDEWEB)

Howard, Chris [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Daigle, Stephen [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Buckner, Matt [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Erikson, Luke E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Runkle, Robert C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stave, Sean C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Champagne, Art [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Cooper, Andrew [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Downen, Lori [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Glasgow, Brian D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kelly, Keegan [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Sallaska, Anne [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States)

2015-02-18

The Multi-sensor Airborne Radiation Survey (MARS) detector is a 14-crystal array of high-purity germanium (HPGe) detectors housed in a single cryostat. The array was used to measure the astrophysical S-factor for the ¹⁴N(p,γ)¹⁵O* reaction for several transition energies at an effective center of mass energy of 163 keV. Owing to the segmented nature of the MARS detector, the effect of gamma-ray summing was greatly reduced in comparison to past experiments which utilized large, single-crystal detectors. The new S-factor values agree within the uncertainties with the past measurements. Details of the analysis and detector performance will be presented.

Performance of a compact multi-crystal high-purity germanium detector array for measuring coincident gamma-ray emissions

Energy Technology Data Exchange (ETDEWEB)

Howard, Chris; Daigle, Stephen; Buckner, Matt [University of North Carolina at Chapel Hill, Chapel Hill, NC 27599 (United States); Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States); Erikson, Luke E.; Runkle, Robert C. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Stave, Sean C., E-mail: Sean.Stave@pnnl.gov [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Champagne, Arthur E.; Cooper, Andrew; Downen, Lori [University of North Carolina at Chapel Hill, Chapel Hill, NC 27599 (United States); Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States); Glasgow, Brian D. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Kelly, Keegan; Sallaska, Anne [University of North Carolina at Chapel Hill, Chapel Hill, NC 27599 (United States); Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States)

2015-05-21

The Multi-sensor Airborne Radiation Survey (MARS) detector is a 14-crystal array of high-purity germanium (HPGe) detectors housed in a single cryostat. The array was used to measure the astrophysical S-factor for the {sup 14}N(p,γ){sup 15}O{sup ⁎} reaction for several transition energies at an effective center-of-mass energy of 163 keV. Owing to the granular nature of the MARS detector, the effect of gamma-ray summing was greatly reduced in comparison to past experiments which utilized large, single-crystal detectors. The new S-factor values agree within their uncertainties with the past measurements. Details of the analysis and detector performance are presented.

Applicability of the spatial autocorrection method for estimation of basement structure in Kanto plain. Array measurements of microtremors close to the Iwatsuki and Shimosa deep borehole observatory; Kanto heiya no kiban kozo suitei no tame no kukan jiko sokanho no tekiyosei. Iwatsuki Shimosa jiban katsudo kansokusei ni okeru array bido kansoku

Energy Technology Data Exchange (ETDEWEB)

Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)

1996-10-01

To investigate applicability of the spatial autocorrection method which is a microtremors exploration method for the estimation of basement structure, array measurements of microtremors were performed using the Iwatsuki and Shimosa deep borehole observatory where detailed structures were clarified as well as the Fuchu and Koto deep borehole observatory. In this study, estimated velocity structures of S-wave were compared with the geological sequence and results of acoustic velocity logging. The phase velocity was estimated by the spatial autocorrection method using FFT. The phase velocity with a smooth normal dispersion was observed in the periodic range from 0.5 to 5 sec in Iwatsuki, and from 0.5 to 4 sec in Shimosa by the combination of four-point circular arrays with radii of 100, 300, and 600 m. The underground structures estimated from the phase velocities coincided well with the geological sequence, and results of acoustic velocity logging and velocity logging for each borehole. For the Iwatsuki borehole, the basement velocity was also estimated properly in the periodic range of observation. While, for the Shimosa borehole, measurements with the period around 6 sec were required to estimate the basement velocity more accurately. 13 refs., 11 figs., 1 tab.

Socioeconomically disadvantaged smokers' ratings of plain and branded cigarette packaging: an experimental study.

Science.gov (United States)

Guillaumier, Ashleigh; Bonevski, Billie; Paul, Chris; Durkin, Sarah; D'Este, Catherine

2014-02-06

This study aimed to test the potential impact of plain packaging for cigarettes on brand appeal among highly socioeconomically disadvantaged smokers using the new design for cigarettes implemented in Australia, which combines plain packaging with larger health warning labels. A 2×2 factorial design trial embedded within a cross-sectional computer touchscreen survey. Data were collected between March and December 2012. Socially disadvantaged welfare aid recipients were recruited through a large Social and Community Service Organisation in New South Wales, Australia. N=354 smokers. The majority of the sample had not completed high school (64%), earned less than $A300/week (55%) and received their income from Government payments (95%). Participants were randomised to one of the four different pack conditions determined by brand name: Winfield versus Benson & Hedges, and packaging type: branded versus plain. Participants were required to rate their assigned pack on measures of brand appeal and purchase intentions. Plain packaging was associated with significantly reduced smoker ratings of 'positive pack characteristics' (p<0.001), 'positive smoker characteristics' (p=0.003) and 'positive taste characteristics' (p=0.033) in the Winfield brand name condition only. Across the four pack conditions, no main differences were found for 'negative smoker characteristics' (p=0.427) or 'negative harm characteristics' (p=0.411). In comparison to plain packaging, the presentation of branded packaging was associated with higher odds of smokers' purchase intentions (OR=2.18, 95% CI 1.34 to 3.54; p=0.002). Plain packs stripped of branding elements, featuring larger health warning labels, were associated with reduced positive cigarette brand image and purchase intentions among highly socioeconomically disadvantaged smokers.

Sensor and method for measuring the areal density of magnetic nanoparticles on a micro-array

NARCIS (Netherlands)

2003-01-01

The present invention relates to a method and a device for magnetic detection of binding of biological molecules on a biochip. A magnetoresistive sensor device for measuring an areal density of magnetic nanoparticles on a micro-array, the magnetic nanoparticles (15) being directly or indirectly

Mountain-Plains Curriculum.

Science.gov (United States)

Mountain-Plains Education and Economic Development Program, Inc., Glasgow AFB, MT.

The document lists the Mountain-Plains curriculum by job title (where applicable), including support courses. The curriculum areas covered are mathematics skills, communication skills, office education, lodging services, food services, marketing and distribution, welding support, automotive, small engines, career guidance, World of Work, health…

Tundra landform and vegetation productivity trend maps for the Arctic Coastal Plain of northern Alaska

Science.gov (United States)

Lara, Mark J.; Nitze, Ingmar; Grosse, Guido; McGuire, A. David

2018-01-01

Arctic tundra landscapes are composed of a complex mosaic of patterned ground features, varying in soil moisture, vegetation composition, and surface hydrology over small spatial scales (10–100 m). The importance of microtopography and associated geomorphic landforms in influencing ecosystem structure and function is well founded, however, spatial data products describing local to regional scale distribution of patterned ground or polygonal tundra geomorphology are largely unavailable. Thus, our understanding of local impacts on regional scale processes (e.g., carbon dynamics) may be limited. We produced two key spatiotemporal datasets spanning the Arctic Coastal Plain of northern Alaska (~60,000 km2) to evaluate climate-geomorphological controls on arctic tundra productivity change, using (1) a novel 30 m classification of polygonal tundra geomorphology and (2) decadal-trends in surface greenness using the Landsat archive (1999–2014). These datasets can be easily integrated and adapted in an array of local to regional applications such as (1) upscaling plot-level measurements (e.g., carbon/energy fluxes), (2) mapping of soils, vegetation, or permafrost, and/or (3) initializing ecosystem biogeochemistry, hydrology, and/or habitat modeling.

South Ilan Plain High-Resolution 3-D S-Wave Velocity from Ambient Noise Tomography

Directory of Open Access Journals (Sweden)

Kai-Xun Chen

2016-06-01

Full Text Available The Ilan Plain in northeastern Taiwan is located at a pivotal point where the Ryukyu trench subduction zone, the northern Taiwan crustal stretching zone, and the ongoing arc-continent collision zone converge. In contrast to the North Ilan Plain, the South Ilan Plain exhibits a thin unconsolidated sedimentary layer with depths ranging from 0 - 1 km, high on-land seismicity and significant SE movements relative to Penghu island. We deployed a dense network of 43 short-period vertical component Texan instruments from June to November 2013 in this study, covering most of the South Ilan Plain and its vicinity. We then used the ambient noise tomography method for simultaneous phase and group Rayleigh wave velocity measurements to invert a high-resolution 3-D S-wave for shallow structures (up to a depth of 2.5 km in the South Ilan Plain. We used the fast marching method for ray tracing to deal with ray bending in an inhomogeneous medium. The resulting rays gradually bend toward high velocity zones with increasing number of iterations. The high velocity zone results are modified by more iterations and the resolutions become higher because ray crossings are proportional to ray densities for evenly distributed stations. The final results agreed well with known sedimentary basement thickness patterns. We observed nearly EW trending fast anomalies beneath the mountainous terrain abutting to the South Ilan Plain. The Chingshui location consistently exhibited a low S-wave velocity zone to a depth of 1.5 km.

The hyperion particle-γ detector array

Energy Technology Data Exchange (ETDEWEB)

Hughes, R.O.; Burke, J.T.; Casperson, R.J.; Ota, S. [Nuclear and Chemical Sciences Division, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Fisher, S.; Parker, J. [Science, Technology and Engineering Division, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Beausang, C.W. [Department of Physics, University of Richmond, 28 Westhampton Way, Richmond, VA 23173 (United States); Dag, M. [Cyclotron Institute, Texas A& M University, College Station, TX 77840 (United States); Humby, P. [Department of Physics, University of Richmond, 28 Westhampton Way, Richmond, VA 23173 (United States); Department of Physics, University of Surrey, Surrey GU27XH (United Kingdom); Koglin, J. [Nuclear and Chemical Sciences Division, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); McCleskey, E.; McIntosh, A.B.; Saastamoinen, A. [Cyclotron Institute, Texas A& M University, College Station, TX 77840 (United States); Tamashiro, A.S. [Department of Nuclear Science and Engineering, Oregon State University, Corvallis, OR 97331 (United States); Wilson, E. [Department of Physics, University of Richmond, 28 Westhampton Way, Richmond, VA 23173 (United States); Wu, T.C. [Department of Physics and Astronomy, University of Utah, Salt Lake City UT 84112-0830 (United States)

2017-06-01

Hyperion is a new high-efficiency charged-particle γ-ray detector array which consists of a segmented silicon telescope for charged-particle detection and up to fourteen high-purity germanium clover detectors for the detection of coincident γ rays. The array will be used in nuclear physics measurements and Stockpile Stewardship studies and replaces the STARLiTeR array. This article discusses the features of the array and presents data collected with the array in the commissioning experiment.

Calibration of Hall sensor array for critical current measurement of YBCO tape with ferromagnetic substrate

International Nuclear Information System (INIS)

Zhu, Yunpeng; Wang, Gang; Liu, Liyuan; Yang, Xinsheng; Zhao, Yong

2015-01-01

Abstract : HAS (Hall sensor array) is a powerful tool to detect the uniformity of HTS (high temperature superconductor) tape through mapping the distribution of remanent or shielding field along the surface of the tape. However, measurement of HTS tape with ferromagnetic parts by HSA is still an issue because the ferromagnetic substrate has influence on the magnetic field around the HTS layer. In this work, a continuous HSA system has been designed to measure the critical current of the YBCO tape with ferromagnetic substrate. The relationship between the remanent field and critical current was calibrated by the finite element method. The result showed that the HSA is an effective method for evaluating the critical current of the HTS tape with ferromagnetic substrate. - Highlight: • A continuous Hall sensor array system has been designed. • The inhomogeneity of YBCO tape with ferromagnetic substrate can be detected by HAS. • Finite element method is an effective method for calibrating the remanent field.

Calibration of Hall sensor array for critical current measurement of YBCO tape with ferromagnetic substrate

Energy Technology Data Exchange (ETDEWEB)

Zhu, Yunpeng; Wang, Gang; Liu, Liyuan [Key laboratory of Magnetic levitation Technologies and Maglev Trains (Ministry of Education), Superconductor and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, 610031 (China); Yang, Xinsheng, E-mail: xsyang@swjtu.edu.cn [Key laboratory of Magnetic levitation Technologies and Maglev Trains (Ministry of Education), Superconductor and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, 610031 (China); Zhao, Yong [Key laboratory of Magnetic levitation Technologies and Maglev Trains (Ministry of Education), Superconductor and New Energy R& D Center, Mail Stop 165#, Southwest Jiaotong University, Chengdu, 610031 (China); Superconductivity Research Group, School of Materials Science and Engineering, University of New South Wale, Sydney 2052, NSW (Australia)

2015-12-15

Abstract : HAS (Hall sensor array) is a powerful tool to detect the uniformity of HTS (high temperature superconductor) tape through mapping the distribution of remanent or shielding field along the surface of the tape. However, measurement of HTS tape with ferromagnetic parts by HSA is still an issue because the ferromagnetic substrate has influence on the magnetic field around the HTS layer. In this work, a continuous HSA system has been designed to measure the critical current of the YBCO tape with ferromagnetic substrate. The relationship between the remanent field and critical current was calibrated by the finite element method. The result showed that the HSA is an effective method for evaluating the critical current of the HTS tape with ferromagnetic substrate. - Highlight: • A continuous Hall sensor array system has been designed. • The inhomogeneity of YBCO tape with ferromagnetic substrate can be detected by HAS. • Finite element method is an effective method for calibrating the remanent field.

27 CFR 9.207 - Outer Coastal Plain.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Outer Coastal Plain. 9.207... Outer Coastal Plain. (a) Name. The name of the viticultural area described in this section is “Outer Coastal Plain”. For purposes of part 4 of this chapter, “Outer Coastal Plain” is a term of viticultural...

Analyzing the Various Approaches of Plain Language Laws.

Science.gov (United States)

Bowen, Betsy A., And Others

1986-01-01

Proposes a two-phase evaluation of the plain language laws that are designed to ensure that consumers can understand and use the personal business contracts they sign so that the best model for plain language legislation can be identified. (DF)

Characterization of memory and measurement history in photoconductivity of nanocrystal arrays

Science.gov (United States)

Fairfield, Jessamyn A.; Dadosh, Tali; Drndic, Marija

2010-10-01

Photoconductivity in nanocrystal films has been previously characterized, but memory effects have received little attention despite their importance for device applications. We show that the magnitude and temperature dependence of the photocurrent in CdSe/ZnS core-shell nanocrystal arrays depends on the illumination and electric field history. Changes in photoconductivity occur on a few-hour timescale, and subband gap illumination of nanocrystals prior to measurements modifies the photocurrent more than band gap illumination. The observed effects can be explained by charge traps within the band gap that are filled or emptied, which may alter nonradiative recombination processes and affect photocurrent.

International collaborative study for the calibration of proposed International Standards for thromboplastin, rabbit, plain and for thromboplastin, recombinant, human, plain

DEFF Research Database (Denmark)

van den Besselaar, A M H P; Chantarangkul, V; Angeloni, F

2018-01-01

BACKGROUND: The availability of International Standards for thromboplastin is essential for the calibration of routine reagents and hence the calculation of the International Normalized Ratio (INR). Stocks of the current 4(th) International Standards are running low. Candidate replacement materia......) international standard (rTF/09). The candidate materials have been accepted by WHO as the 5(th) International Standards for thromboplastin, rabbit plain, and thromboplastin, recombinant, human, plain. This article is protected by copyright. All rights reserved.......BACKGROUND: The availability of International Standards for thromboplastin is essential for the calibration of routine reagents and hence the calculation of the International Normalized Ratio (INR). Stocks of the current 4(th) International Standards are running low. Candidate replacement materials...... have been prepared. This report describes the calibration of the proposed 5(th) International Standards for thromboplastin, rabbit, plain (coded RBT/16) and for thromboplastin, recombinant, human, plain (coded rTF/16). METHODS: An international collaborative study was carried out for the assignment...

Herbage productivity of the Winneba plains of Ghana | Fleischer ...

African Journals Online (AJOL)

The biomass productivity of the Winneba plains of Ghana was measured between January 1990 and February 1992. Ten sampling sites were chosen for the study. An area of 5.0 m W 5.0 m was demarcated and within it an area of 1.0 m W 1.0 m was harvested at monthly intervals, clipped by means of sickle at 5 cm above ...

A New Boundary for the High Plains - Ogallala Aquifer Complex

Science.gov (United States)

Haacker, E. M.; Nozari, S.; Kendall, A. D.

2017-12-01

In the semi-arid Great Plains, water is the key ingredient for crop growth: the difference between meager yields for many crops and an agricultural bonanza. The High Plains-Ogallala Aquifer complex (HPA) underlies 452,000 square kilometers of the region, and over 95% of water withdrawn from the aquifer is used for irrigation. Much of the HPA is being pumped unsustainably, and since the region is heavily reliant on this resource for its social and economic health, the High Plains has been a leader in groundwater management planning. However, the geographic boundary of the High Plains region fails to reflect the hydrogeological realities of the aquifer. The current boundary, recognizable from countless textbooks and news articles, is only slightly modified from a version from the 1980's, and largely follows the physiographic borders of the High Plains - defined by surface features such as escarpments and rivers - rather than the edges of water-bearing sediment sufficient for high-volume pumping. This is supported by three lines of evidence: hydrogeological observations from the original aquifer boundary determination; the extent of irrigated land, as estimated by MODIS-MIrAD data; and statistical estimates of saturated thickness, incorporating improved maps of the aquifer base and an additional 35 years of water table measurements. In this project, new maps of saturated thickness are used to create an updated aquifer boundary, which conforms with the standard definition of an aquifer as a package of sediment that yields enough water to be economically pumped. This has major implications for social and physical models, as well as water planning and estimates of sustainability for the HPA. Much of the area of the HPA that has been labeled `sustainable' based upon estimates of recharge relative to pumping estimates falls outside the updated aquifer boundary. In reality, the sustainably-pumped area of this updated aquifer boundary is far smaller—a fact that if more

Formation mechanism of land subsidence in the North China Plain

Science.gov (United States)

Guo, Haipeng; Cheng, Guoming

2014-05-01

Land subsidence is a progressive and gradual geological disaster, whose development is irreversible. Due to rapid development of industrialization and urbanization, land subsidence occurs commonly in the North China Plain, and has become the main environmental factor impacting sustainable economic and social development. This study presents a brief review on the current situation of land subsidence in the North China Plain. Then the hydrologic, hydrogeologic and anthropogenic conditions favorable for the formation of land subsidence are analyzed, indicating that the formation of land subsidence is mainly determined by local geological condition and enabling conditions, e.g. long-term excessive exploitation of groundwater and engineering construction. A correlation analysis was conducted in both the North China Plain and Cangzhou region, a typical area where severe land subsidence occurs, of the quantitative relationship between deep groundwater yield and the land subsidence. The analysis results indicate that the land subsidence volume accounts for 40% to 44% of deep water yield in the North China Plain, indirectly showing the proportion of released water from compressibility of the aquifer and the aquitard in deep groundwater yield. In Cangzhou region, this proportion was calculated as 58%, far greater than that of the North China Plain. This is induced by the local lithologic structure and recharge condition of deep groundwater in Cangzhou region. The analysis of soil samples in Cangzhou region shows that strong relations exist among different physical parameters, and good change laws of compression with depth and pressure are found for soil samples. The hydraulic conductivities of clay are six orders of magnitude greater than those of the aquifer, implying the strong hypothesis of land subsidence. This analysis provides data and scientific basis for further study on formation mechanism of land subsidence in Cangzhou region and objective evaluation of its

Spatial profile measurements of ion-confining potentials using novel position-sensitive ion-energy spectrometer arrays

International Nuclear Information System (INIS)

Yoshida, M.; Cho, T.; Hirata, M.; Ito, H.; Kohagura, J.; Yatsu, K.; Miyoshi, S.

2003-01-01

The first experimental demonstration of simultaneous measurements of temporally and spatially resolved ion-confining potentials phi c and end-loss-ion fluxes I ELA has been carried out during a single plasma discharge alone by the use of newly designed ion-energy-spectrometer arrays installed in both end regions of the GAMMA 10 tandem mirror. This position-sensitive ion-detector structure is proposed to obtain precise ion-energy spectra without any perturbations from simultaneously incident energetic electrons into the arrays. The relation between phi c and I ELA is physically interpreted in terms of Pastukhov's potential confinement theory. In particular, the importance of axisymmetric phi c formation is found for the plasma confinement

Examination of measurement and its method of compensation of the sensitivity distribution using phased array coil for body scan

CERN Document Server

Kimura, T; Iizuka, A; Taniguchi, Y; Ishikuro, A; Hongo, T; Inoue, H; Ogura, A

2003-01-01

The influence on the quality of images by measurement of a sensitivity distribution and the use of a sensitivity compensation filter was considered using an opposite-type phased array coil and volume-type phased array coil. With the opposite-type phased array coil, the relation between coil interval and filter was investigated for the image intensity correction (IIC) filter, surface coil intensity correction (SCIC) filter (GE), and the Normalize filter (SIEMENS). The SCIC filter and Normalize filter showed distance dependability over the coil interval of signal-to-noise ratio (SNR) and uniformity was observed, and the existence of an optimal coil interval was suggested. Moreover, with the IIC filter, distance dependability over a coil interval was small, and the decrease in contrast with use was remarkable. On the other hand, with the volume-type phased array coil, the overlap of an array element was investigated to determine the influence it had on sensitivity distribution. Although the value stabilized in t...

Tobacco plain packaging: Evidence based policy or public health advocacy?

Science.gov (United States)

McKeganey, Neil; Russell, Christopher

2015-06-01

In December 2012, Australia became the first country to require all tobacco products be sold solely in standardised or 'plain' packaging, bereft of the manufacturers' trademarked branding and colours, although retaining large graphic and text health warnings. Following the publication of Sir Cyril Chantler's review of the evidence on the effects of plain tobacco packaging, the Ministers of the United Kingdom Parliament voted in March 2015 to implement similar legislation. Support for plain packaging derives from the belief that tobacco products sold in plain packs have reduced appeal and so are more likely to deter young people and non-smokers from starting tobacco use, and more likely to motivate smokers to quit and stay quit. This article considers why support for the plain packaging policy has grown among tobacco control researchers, public health advocates and government ministers, and reviews Australian survey data that speak to the possible introductory effect of plain packaging on smoking prevalence within Australia. The article concludes by emphasising the need for more detailed research to be undertaken before judging the capacity of the plain packaging policy to deliver the multitude of positive effects that have been claimed by its most ardent supporters. Copyright © 2015 Elsevier B.V. All rights reserved.

Socioeconomically disadvantaged smokers’ ratings of plain and branded cigarette packaging: an experimental study

Science.gov (United States)

Guillaumier, Ashleigh; Bonevski, Billie; Paul, Chris; Durkin, Sarah; D'Este, Catherine

2014-01-01

Objectives This study aimed to test the potential impact of plain packaging for cigarettes on brand appeal among highly socioeconomically disadvantaged smokers using the new design for cigarettes implemented in Australia, which combines plain packaging with larger health warning labels. Design A 2×2 factorial design trial embedded within a cross-sectional computer touchscreen survey. Data were collected between March and December 2012. Setting Socially disadvantaged welfare aid recipients were recruited through a large Social and Community Service Organisation in New South Wales, Australia. Participants N=354 smokers. The majority of the sample had not completed high school (64%), earned less than $A300/week (55%) and received their income from Government payments (95%). Interventions Participants were randomised to one of the four different pack conditions determined by brand name: Winfield versus Benson & Hedges, and packaging type: branded versus plain. Participants were required to rate their assigned pack on measures of brand appeal and purchase intentions. Results Plain packaging was associated with significantly reduced smoker ratings of ‘positive pack characteristics’ (p<0.001), ‘positive smoker characteristics’ (p=0.003) and ‘positive taste characteristics’ (p=0.033) in the Winfield brand name condition only. Across the four pack conditions, no main differences were found for ‘negative smoker characteristics’ (p=0.427) or ‘negative harm characteristics’ (p=0.411). In comparison to plain packaging, the presentation of branded packaging was associated with higher odds of smokers’ purchase intentions (OR=2.18, 95% CI 1.34 to 3.54; p=0.002). Conclusions Plain packs stripped of branding elements, featuring larger health warning labels, were associated with reduced positive cigarette brand image and purchase intentions among highly socioeconomically disadvantaged smokers. PMID:24503299

Utopia Plain

Science.gov (United States)

2006-01-01

5 March 2006 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a dark-toned, cratered plain in southwest Utopia Planitia. Large, light-toned, windblown ripples reside on the floors of many of the depressions in the scene, including a long, linear, trough. Location near: 30.3oN, 255.3oW Image width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Winter

Perceptions of plain packaging among young adult roll-your-own smokers in France: a naturalistic approach.

Science.gov (United States)

Gallopel-Morvan, Karine; Moodie, Crawford; Eker, Figen; Beguinot, Emmanuelle; Martinet, Yves

2015-03-01

We explored, for the first time, young adult roll-your-own smokers' response to using plain packaging in real-world settings. Naturalistic research was employed, where 133 French young adult smokers (18-25 years of age) used plain roll-your-own packs for 10 days; the plain packs they were provided with contained their usual brand of rolling tobacco and displayed the name of their usual brand. Participants were recruited in five cities in France (Paris, Marseille, Metz, Nantes, Toulouse) and completed two questionnaires to measure their response to their own branded packs and the plain packs. Both questionnaires assessed pack perceptions, brand attachment, product perceptions (eg, taste, quality, natural), feelings about smoking (satisfying, pleasurable), feelings when using the pack in front of others (embarrassment, image), warning response (credibility, awareness of risks) and smoking-related behaviour (eg, consumption, quitting). Compared to their own fully branded packs, plain packs were associated with less positive pack and product perceptions, lower brand attachment and less positive feelings about smoking and feelings when using the pack in front of others. Participants were also more likely to report feeling like reducing consumption and quitting when using the plain packs, and more likely to feel like missing out on rolling a cigarette. No significant differences between the two pack types (plain and branded) were found in terms of credibility of warnings and perceptions of level of tar. The study suggests that the impacts of plain packaging for roll-your-own cigarette smokers are the same as for smokers of factory-made cigarettes. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The potential impact of plain packaging of cigarette products among Brazilian young women: an experimental study

Directory of Open Access Journals (Sweden)

White Christine M

2012-09-01

Full Text Available Abstract Background Tobacco use is responsible for 5.4 million deaths every year worldwide and is a leading cause of preventable death. The burden of these deaths is rapidly shifting to low and middle-income countries, such as Brazil. Brazil has prohibited most forms of tobacco advertising; however, the cigarette pack remains a primary source of marketing. The current study examined how tobacco packaging influences brand appeal and perceptions of health risk among young women in Brazil. Methods A between-subjects experiment was conducted in which 640 Brazilian women aged 16–26 participated in an online survey. Participants were randomized to view 10 cigarette packages according to one of three experimental conditions: standard branded packages, the same packs without brand imagery (“plain packaging”, or the same packs without brand imagery or descriptors (e.g., flavors. Participants rated packages on perceived appeal, taste, health risk, smoothness, and smoker attributes. Finally, participants were shown a range of branded and plain packs from which they could select one as a free gift, which constituted a behavioral measure of appeal. Results Branded packs were rated as significantly more appealing, better tasting, and smoother on the throat than plain packs. Branded packs were also associated with a greater number of positive smoker attributes including style and sophistication, and were perceived as more likely to be smoked by females than the plain packs. Removing descriptors from the plain packs further decreased the ratings of appeal, taste and smoothness, and also reduced associations with positive attributes. In the pack offer, participants were three times more likely to select branded packs than plain packs. Conclusions Plain packaging and removal of descriptors may reduce the appeal of smoking for youth and young adults, and consequently reduce smoking susceptibility. Overall, the findings provide support for plain packaging

Plain Language to Communicate Physical Activity Information: A Website Content Analysis.

Science.gov (United States)

Paige, Samantha R; Black, David R; Mattson, Marifran; Coster, Daniel C; Stellefson, Michael

2018-04-01

Plain language techniques are health literacy universal precautions intended to enhance health care system navigation and health outcomes. Physical activity (PA) is a popular topic on the Internet, yet it is unknown if information is communicated in plain language. This study examined how plain language techniques are included in PA websites, and if the use of plain language techniques varies according to search procedures (keyword, search engine) and website host source (government, commercial, educational/organizational). Three keywords ("physical activity," "fitness," and "exercise") were independently entered into three search engines (Google, Bing, and Yahoo) to locate a nonprobability sample of websites ( N = 61). Fourteen plain language techniques were coded within each website to examine content formatting, clarity and conciseness, and multimedia use. Approximately half ( M = 6.59; SD = 1.68) of the plain language techniques were included in each website. Keyword physical activity resulted in websites with fewer clear and concise plain language techniques ( p websites with more clear and concise techniques ( p language techniques did not vary by search engine or the website host source. Accessing PA information that is easy to understand and behaviorally oriented may remain a challenge for users. Transdisciplinary collaborations are needed to optimize plain language techniques while communicating online PA information.

Stratigraphy of the Martian northern plains

Science.gov (United States)

Tanaka, K. L.

1993-01-01

The northern plains of Mars are roughly defined as the large continuous region of lowlands that lies below Martian datum, plus higher areas within the region that were built up by volcanism, sedimentation, tectonism, and impacts. These northern lowlands span about 50 x 10(exp 6) km(sup 2) or 35 percent of the planet's surface. The age and origin of the lowlands continue to be debated by proponents of impact and tectonic explanations. Geologic mapping and topical studies indicate that volcanic, fluvial, and eolian deposition have played major roles in the infilling of this vast depression. Periglacial, glacial, fluvial, eolian, tectonic, and impact processes have locally modified the surface. Because of the northern plains' complex history of sedimentation and modification, much of their stratigraphy was obscured. Thus the stratigraphy developed is necessarily vague and provisional: it is based on various clues from within the lowlands as well as from highland areas within and bordering the plains. The results are summarized.

Environmental isotopes in New Zealand hydrology ; 4. Oxygen isotope variations in subsurface waters of the Waimea Plains, Nelson

International Nuclear Information System (INIS)

Stewart, M.K.; Dicker, M.J.I.; Johnston, M.R.

1981-01-01

Oxygen isotope measurements of ground and surface waters of the Waimea Plains, Nelson, have been used to identify sources of water in aquifers beneath the plains. Major rivers flowing onto the plains are from higher-altitude catchments (maximum altitude 2000 m) and have delta O 18 approximately equal to -7.2%, whereas rainfall on the plains and adjacent low-altitude catchment streams have delta O 18 approximately equal to -6.2%. The delta O 18 measurements indicate that the 3 major aquifer units, the ''Lower Confined Aquifers'' and the ''Upper Confined Aquifers'' in the Hope Gravel (Late Pleistocene) and the ''Unconfined Aquifers'' in the Appleby Gravel (Holocene) are recharged from different sources. The ''Lower Confined Aquifers'' probably receive slow recharge in the south near Brightwater. The ''Upper Confined Aquifers'' are recharged, in the south, from the Wairoa River and locally in the north are connected with the unconfined aquifers. The ''Unconfined Aquifers'' are recharged from the Waimea River and, away from the river, from rainfall. Intermixing of water, via multiple screened wells, between the various aquifers is also indicated. (author). 5 refs., 5 figs., 1 tab

Reducing radiation dose in liver enhanced CT scan by setting mAs according to plain scan noise

International Nuclear Information System (INIS)

Yang Shangwen; He Jian; Yang Xianfeng; Zhou Kefeng; Xin Xiaoyan; Hu Anning; Zhu Bin

2013-01-01

Objective: To investigate the feasibility of setting mAs in liver enhanced CT scan according to plain scan noise with fixed mA CT scanner, in order to reduce the radiation dose. Methods: One hundred continuous patients underwent liver enhanced CT scan (group A) prospectively. Two hundred and fifty mAs was used in plain and enhanced CT scans. Noises of plain and venous phase CT images were measured, and the image quality was evaluated. The equation between mAs of enhanced scan and noise of plain scan image was derived. Another 100 continuous patients underwent liver enhanced CT scan (group B). Enhanced scan mAs was calculated from noise on plain scan by using the equation above. Noises on venous phase images were measured and the image quality was measured. Based on body mass index (BMI), patients in groups A and B were divided into three subgroups respectively: BMI < 18.5 kg/m 2 , 18.5 kg/m 2 ≤ BMI < 25.0 kg/m 2 and BMI ≥ 25.0 kg/m 2 . Image quality score was compared with nonparametric rank sum test, CT dose index (CTDI) and effective dose (ED) were measured and compared between each subgroup with 2 independent samples t or t' test. Results: The equation between enhanced scan mAs (mAsX) and plain scan noise (SDp) was as follows: mAsX = mAs1 × [(0.989 × SDp + 1.06) /SDx] 2 , mAs1 = 250 mAs, SDx = 13. In patients with BMI < 18.5 kg/m 2 , ED of group A [(6.86 ± 0.38) mSv, n = 12] was significantly higher than group B [(2.66 ± 0.46) mSv, n = 10)] (t = 18.52, P < 0.01). In patients with 18.5 kg/m 2 ≤ BMI < 25.0 kg/m 2 , ED of group A [(7.08 ± 0.91) mSv, n = 66] was significantly higher than group B [(4.50 ± 1.41) mSv, n = 73] (t' = 10.57, P < 0.01). In patients with BMI ≥ 25.0 kg/m 2 , there was no significant difference between EDs of group A (7.54 ± 0.62 mSv, n = 22) and group B [(8.19 ± 3.16) mSv, n = 17] (t' = 0.89, P = 0.39). Image quality of 5 patients in group A and none in group B did not meet the diagnostic requirement

[Research on demodulation system for human body temperature measurement of intelligent clothing based on arrayed waveguide grating].

Science.gov (United States)

Yu, Xiao-gang; Miao, Chang-yun; Li, Hong-qiang; Li, En-bang; Liu, Zhi-hui; Wei, Ke-jia

2012-08-01

A system for demodulating distributed fiber Bragg grating sensors of the intelligent clothing was researched and realized, which is based on arrayed waveguide grating. The principle of demodulation method based on arrayed waveguide grating was analyzed, intensity--demodulating method was used to interrogate the wavelength of the fiber Bragg grating based on the building up of an experimental platform, and demodulation experiment of pre and post series of fiber Bragg grating was completed. The results show that the wavelength demodulation of the system has high linearity for fiber Bragg grating, the system gives a wavelength accuracy of 0.001 nm, and demodulation error caused by crosstalk between different sensors is 0.0005 nm. The measurement error of human body temperature is +/- 0.16 degrees C. It can be applied to the human body temperature measurement.

Ocean-Bottom Topography: The Divide between the Sohm and Hatteras Abyssal Plains.

Science.gov (United States)

Pratt, R M

1965-06-18

A compilation of precision echo soundings has delineated the complex topography between the Sohm and Hatteras abyssal plains off the Atlantic coast of the United States. At present the divide between the two plains is a broad, flat area about 4950 meters deep; however, the configuration of channels and depressions suggests spillage of turbidity currents from the Sohm Plain into the Hatteras Plain and a shifting of the divide toward the northeast. Hudson Canyon terminates in the divide area and has probably fed sediment into both plains.

Desert plains classification based on Geomorphometrical parameters (Case study: Aghda, Yazd)

Science.gov (United States)

Tazeh, mahdi; Kalantari, Saeideh

2013-04-01

This research focuses on plains. There are several tremendous methods and classification which presented for plain classification. One of The natural resource based classification which is mostly using in Iran, classified plains into three types, Erosional Pediment, Denudation Pediment Aggradational Piedmont. The qualitative and quantitative factors to differentiate them from each other are also used appropriately. In this study effective Geomorphometrical parameters in differentiate landforms were applied for plain. Geomorphometrical parameters are calculable and can be extracted using mathematical equations and the corresponding relations on digital elevation model. Geomorphometrical parameters used in this study included Percent of Slope, Plan Curvature, Profile Curvature, Minimum Curvature, the Maximum Curvature, Cross sectional Curvature, Longitudinal Curvature and Gaussian Curvature. The results indicated that the most important affecting Geomorphometrical parameters for plain and desert classifications includes: Percent of Slope, Minimum Curvature, Profile Curvature, and Longitudinal Curvature. Key Words: Plain, Geomorphometry, Classification, Biophysical, Yazd Khezarabad.

Late Quarternary evolution of the northern Hatteras Abyssal Plain

International Nuclear Information System (INIS)

Dickson, S.M.; Laine, E.P.

1986-05-01

The sedimentary history and seismic structure of a deep-water turbidite basin in the Western North Atlantic Ocean has been investigated to understand further the evolution of abyssal plains. This study integrates analyses of sedimentary and seismic facies in order to examine the temporal and spatial patterns of sedimentation on the northern Hatteras Abyssal Plain during the Late Quaternary. Forty deep-sea sediment cores and 6000 km of high resolution (3.5 kHz) seismic reflection profiles from within 31-34 0 N and 69-74 0 W include portions of the Hatteras Outer Ridge, Lower Continental Rise and Bermuda Rise as well as the northern Hatteras Abyssal Plain. Seismic profiles (within 32-33 0 N, 70-71.5 0 W) define two acoustically-transparent seismic units beneath the Plain. The composition of these seismic units has been investigated with sediment cores. This study has found two notable features in the sedimentary framework of the Plain that appear to have resulted from temporal changes in sediment supply. The most recent change, a postglacial decline in turbidity current activity, produced a diagenetic iron enrichment at the Pleistocene-Holocene boundary. The stratigraphic thickness affected by diagenesis is related spatially to patterns of turbidite sedimentation. An earlier change, discovered in this research, occurred during the Wisconsinian glaciation and brought coarser-grained turbidity currents to the northern Plain. Deposition of sands from these flows appears to have been locally controlled by a broad topographic feature with less than ten meters relief. As a result of the topographic influence, there are abrupt boundaries, both verically and laterally, between an older mud facies and a younger sandy turbidite facies of the Plain

Development of a prototype PET scanner with depth-of-interaction measurement using solid-state photomultiplier arrays and parallel readout electronics.

Science.gov (United States)

Shao, Yiping; Sun, Xishan; Lan, Kejian A; Bircher, Chad; Lou, Kai; Deng, Zhi

2014-03-07

In this study, we developed a prototype animal PET by applying several novel technologies to use solid-state photomultiplier (SSPM) arrays to measure the depth of interaction (DOI) and improve imaging performance. Each PET detector has an 8 × 8 array of about 1.9 × 1.9 × 30.0 mm(3) lutetium-yttrium-oxyorthosilicate scintillators, with each end optically connected to an SSPM array (16 channels in a 4 × 4 matrix) through a light guide to enable continuous DOI measurement. Each SSPM has an active area of about 3 × 3 mm(2), and its output is read by a custom-developed application-specific integrated circuit to directly convert analogue signals to digital timing pulses that encode the interaction information. These pulses are transferred to and are decoded by a field-programmable gate array-based time-to-digital convertor for coincident event selection and data acquisition. The independent readout of each SSPM and the parallel signal process can significantly improve the signal-to-noise ratio and enable the use of flexible algorithms for different data processes. The prototype PET consists of two rotating detector panels on a portable gantry with four detectors in each panel to provide 16 mm axial and variable transaxial field-of-view (FOV) sizes. List-mode ordered subset expectation maximization image reconstruction was implemented. The measured mean energy, coincidence timing and DOI resolution for a crystal were about 17.6%, 2.8 ns and 5.6 mm, respectively. The measured transaxial resolutions at the center of the FOV were 2.0 mm and 2.3 mm for images reconstructed with and without DOI, respectively. In addition, the resolutions across the FOV with DOI were substantially better than those without DOI. The quality of PET images of both a hot-rod phantom and mouse acquired with DOI was much higher than that of images obtained without DOI. This study demonstrates that SSPM arrays and advanced readout/processing electronics can be used to develop a practical DOI-measureable

Study of the malaria situation in forested foothill and nearby plain areas of Myanmar.

Science.gov (United States)

Myint, L; Ye, H

1991-12-01

A longitudinal demographic-parasitological survey on malaria was conducted at 10 weekly intervals starting from September in one foothill village with the population of 1,095 and one epidemiologically comparable plain village with the population of 962 in Kyauktaga township, Bago division, 120 miles north of Yangon. The objective was to describe and analyse the current malaria situation in a forested foothill area and an adjacent plain area. Ten weekly blood film collections for malaria parasite examination, six monthly sera collections on filter paper for serological examination from the whole study population and ten weekly splenic measurements from 2-9 year children were done. The malaria parasite rate in the foothill area was invariably higher than that in the plain area in all age groups throughout the study period. Moreover, the parasite rate decreased with the increase in distance from the forested foothill area indicating that the deep forest malaria may have some influence on the foothill villages. The total age specific parasite rate in foothill villages was found to be highest in the 5-8 year age group and decreased as the age advanced which may be due to the increasing immunity. The study revealed the presence of local transmission in the foothill village. From these data it is evident that new village sites should be chosen at least 5 miles away from the forest fringe and the malaria control measures in the plain area should utilize chemoprophylaxis and effective chemotherapy focusing on the people who travel into the forest.

Geohazards (floods and landslides in the Ndop plain, Cameroon volcanic line

Directory of Open Access Journals (Sweden)

Wotchoko Pierre

2016-07-01

Full Text Available The Ndop Plain, located along the Cameroon Volcanic Line (CVL, is a volcano-tectonic plain, formed by a series of tectonic movements, volcanic eruptions and sedimentation phases. Floods (annually and landslides (occasionally occur with devastating environmental effects. However, this plain attracts a lot of inhabitants owing to its fertile alluvial soils. With demographic explosion in the plain, the inhabitants (143,000 people tend to farm and inhabit new zones which are prone to these geohazards. In this paper, we use field observations, laboratory analyses, satellite imagery and complementary methods using appropriate software to establish hazard (flood and landslide maps of the Ndop Plain. Natural factors as well as anthropogenic factors are considered.

Development of the microphone array measurement technique for application to cryogenic wind tunnels; Entwicklung der Mikrofonarraymesstechnik fuer die experimentelle Anwendung in kryogenen Windkanaelen

Energy Technology Data Exchange (ETDEWEB)

Ahlefeldt, Thomas

2013-02-01

The present work deals with the development of the microphone array measurement technique for application to cryogenic wind tunnels at temperatures down to 100 K. In contrast to conventional wind tunnels, in cryogenic wind tunnels the Reynolds number can be changed independent of the Mach number. Therefore the applicability of the microphone array measurement technique to cryogenic wind tunnels allows the independent investigation of Mach and Reynolds number effects for aeroacoustic sources. For this purpose two microphone arrays suitable for cryogenic application have been developed. A small array was used for a validation experiment using a single-rod configuration as an aeroacoustic noise source; the experience gained therefrom being then used to develop a larger array. This array was used to finally demonstrate the applicability of the measuring technology to an airplane half model. For the development of both arrays several factors had to be considered, such as, for example, the contraction arising from the low temperatures and the influence of the temperature on the microphone frequency response. In the validation experiment, acoustic array measurements have been performed using the small microphone array with 21 microphones in a cryogenic wind tunnel for various Mach and Reynolds numbers, using a single-rod configuration. The aeroacoustic source induced by the rod could be identified by the microphone.array at ambient as well as at cryogenic temperatures. The radiated sound powers were compared with predictions from two models: one model was based on a dimensional analysis of the measured data without taking into consideration the Reynolds number. The measured data with this model could be better fitted by a speed law with the exponent 6.7 rather than the expected 6.0. The second model was based on an analytical model for sound radiation from a single-rod configuration which took into account variables dependent on the Reynolds number. The comparison with

Two depositional models for Pliocene coastal plain fluvial systems, Goliad Formation, south Texas Gulf Coastal plain

International Nuclear Information System (INIS)

Hoel, H.D.; Galloway, W.E.

1983-01-01

The Goliad Formation consists of four depositional systems-the Realitos and Mathis bed-load fluvial systems in the southwest and the Cuero and Eagle Lake mixed-load fluvial systems in the northeast. Five facies are recognized in the Realitos and Mathis bed-load fluvial systems: (1) primary channel-fill facies, (2) chaotic flood channel-fill facies, (3) complex splay facies, (4) flood plain facies, and (5) playa facies. A model for Realitos-Mathis depositional environments shows arid-climate braided stream complexes with extremely coarse sediment load, highly variable discharge, and marked channel instability. Broad, shallow, straight to slightly sinuous primary channels were flanked by wide flood channels. Flood channels passed laterally into broad, low-relief flood plains. Small playas occupied topographic lows near large channel axes. Three facies are recognized in the Cuero and Eagle Lake mixed-load fluvial systems: (1) channel-fill facies, (2) crevasse splay facies, and (3) flood plain facies. A model for Cuero-Eagle Lake depositional environments shows coarse-grained meander belts in a semi-arid climate. Slightly to moderately sinuous meandering streams were flanked by low, poorly developed natural levees. Crevasse splays were common, but tended to be broad and ill-defined. Extensive, low-relief flood plains occupied interaxial areas. The model proposed for the Realitos and Mathis fluvial systems may aid in recognition of analogous ancient depositional systems. In addition, since facies characteristics exercise broad controls on Goliad uranium mineralization, the proposed depositional models aid in defining target zones for Goliad uranium exploration

The Great Plains low-level jet (LLJ) during the atmospheric radiation measurement (ARM) intensive observation period (IOP)-4 and simulations of land use pattern effect on the LLJ

Energy Technology Data Exchange (ETDEWEB)

Wu, Y.; Raman, S. [North Carolina State Univ., Raleigh, NC (United States)

1996-04-01

The Great Plains low-level jet (LLJ) is an important element of the low-level atmospheric circulation. It transports water vapor from the Gulf of Mexico, which in turn affects the development of weather over the Great Plains of the central United States. The LLJ is generally recognized as a complex response of the atmospheric boundary layer to the diurnal cycle of thermal forcing. Early studies have attributed the Great Plains LLJ to the diurnal oscillations of frictional effect, buoyancy over sloping terrain, and the blocking effects of the Rocky Mountains. Recent investigations show that the speed of the LLJ is also affected by the soil type and soil moisture. Some studies also suggest that synoptic patterns may play an important role in the development of the LLJ. Land surface heterogeneties significantly affect mesoscale circulations by generating strong contrasts in surface thermal fluxes. Thus one would expect that the land use pattern should have effects on the LLJ`s development and structure. In this study, we try to determine the relative roles of the synoptic forcing, planetary boundary layers (PBL) processes, and the land use pattern in the formation of the LLJ using the observations from the Atmospheric Radiation Measurement (ARM) Intensive Operation Period (IOP)-4 and numerical sensitivity tests.

Braid-plain dynamics and bank erosion along the Matanuska River, Alaska

Science.gov (United States)

Curran, J. H.

2009-12-01

Braid-plain activity and geomorphic features in the Matanuska River in southcentral Alaska between 1949 and 2006 were examined to support a bank erosion hazard assessment. The glacial Matanuska River drains 6,500 km2 and is braided for 85 percent of its 150 km course, which parallels a major highway and flows through the towns of Sutton and Palmer, Alaska. The historical braid plain was defined as the envelope of areas with active channels, unvegetated bars, or vegetated bars with evidence of channels since 1949 and delineated in a GIS from 1949, 1962, and 2006 aerial orthoimagery. We created a strip map of bank height and composition (primarily bedrock and unconsolidated sediment) at braid-plain margins and outlined valley bottom features (terraces and tributary fans) adjacent to the braid plain to assess erodibility. Braid-plain dynamism has created a mosaic of extensive lightly vegetated bars interspersed with forested bars in strips along the banks and in small mid-channel positions. Abandoned channels filled with groundwater or tributary streamflow have created clearwater side channels within these bars that serve as the primary spawning location for chum, sockeye, and coho salmon in the Matanuska River basin. Erosion magnitudes for the periods 1949-1962 and 1962-2006 were computed as braid-plain expansion at transects across the historical braid-plain boundaries. Episodic, spatially distributed erosion and the antiquity of some eroded surfaces suggests that average annual erosion rates at a location are not adequate for assessing future erosion at that location in a braid plain. Lateral expansion caused bank erosion of 100 -275 m at 20 locations over the full period, about half at tributary fans and most occurring in a single time period. Minor growth of tributary fans constricted the braid plain, and emerging terraces have the potential to shrink the braid plain. Eroded banks included undated but pre-historic fluvial terraces and tributary fans. Where

Post-Irradiation Examination of Array Targets - Part I

Energy Technology Data Exchange (ETDEWEB)

Icenhour, A.S.

2004-01-23

During FY 2001, two arrays, each containing seven neptunium-loaded targets, were irradiated at the Advanced Test Reactor in Idaho to examine the influence of multi-target self-shielding on {sup 236}Pu content and to evaluate fission product release data. One array consisted of seven targets that contained 10 vol% NpO{sub 2} pellets, while the other array consisted of seven targets that contained 20 vol % NpO{sub 2} pellets. The arrays were located in the same irradiation facility but were axially separated to minimize the influence of one array on the other. Each target also contained a dosimeter package, which consisted of a small NpO{sub 2} wire that was inside a vanadium container. After completion of irradiation and shipment back to the Oak Ridge National Laboratory, nine of the targets (four from the 10 vol% array and five from the 20 vol% array) were punctured for pressure measurement and measurement of {sup 85}Kr. These nine targets and the associated dosimeters were then chemically processed to measure the residual neptunium, total plutonium production, {sup 238}Pu production, and {sup 236}Pu concentration at discharge. The amount and isotopic composition of fission products were also measured. This report provides the results of the processing and analysis of the nine targets.

Using Measured Plane-of-Array Data Directly in Photovoltaic Modeling: Methodology and Validation: Preprint

Energy Technology Data Exchange (ETDEWEB)

Freeman, Janine; Freestate, David; Riley, Cameron; Hobbs, William

2016-11-01

Measured plane-of-array (POA) irradiance may provide a lower-cost alternative to standard irradiance component data for photovoltaic (PV) system performance modeling without loss of accuracy. Previous work has shown that transposition models typically used by PV models to calculate POA irradiance from horizontal data introduce error into the POA irradiance estimates, and that measured POA data can correlate better to measured performance data. However, popular PV modeling tools historically have not directly used input POA data. This paper introduces a new capability in NREL's System Advisor Model (SAM) to directly use POA data in PV modeling, and compares SAM results from both POA irradiance and irradiance components inputs against measured performance data for eight operating PV systems.

Plains Energy Services Ltd. 1998 annual report

International Nuclear Information System (INIS)

1999-01-01

Plains Energy Services Ltd. (Plains) is a two year old public company in the oil and gas service industry. It provides an integrated pool of services, concentrating on the life cycle of oil and gas wells as the driver for its expansion. Although the industry saw a marked decrease in well drilling activity for 1998, Plains was able to sustain a consistent income and cash flow because of its focus on ensuring access to the well during drilling, completion, production and abandonment. For 1998, revenue reached a record $93.3 million, an 85 per cent increase over 1997. This report presented Plain's major achievements for 1998. These included the completed construction of a technical, machining and manufacturing facility to enhance the development and implementation of technology and equipment among all business units. The company also introduced coiled tubing drilling services in the North American marketplace, as well as the first commercial version of a casing inspection tool. Plain's also introduced production logging through their wireline services business and applied for four new patents in relation to downhole tool development. In 1998, the company consolidated their operations into four divisions including consolidation of administration, benefits, banking and related overhead services. This report also described the company's efforts in addressing the year 2000 challenge. The company's consolidated financial statements were presented for the benefit of shareholders. These included statements of earnings and deficit, balance sheets, as well as statements of changes in financial position. Notes to the consolidated financial statements included highlights of significant accounting policies, changes in accounting policies, acquisitions, discontinued operations, and capital assets. tabs., figs

Necrotizing fasciitis : plain radiographic and CT findings

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Dae; Park, Jeong Hee; Jeon, Hae Jeong; Lim, Jong Nam; Heo, Tae Haeng; Park, Dong Rib [Konkuk Univ. College of Medicine, Seoul (Korea, Republic of)

1996-11-01

To evaluate the plain radiographic and CT findings of the necrotizing fasciitis. We retrospectively reviewed the radiologic findings of 4 cases with necrotizing fasciitis. Three cases were proven pathologically. We evaluated pattern and extent of the gas shadows in plain films. CT findings were analysed, with emphasis on : (a) gas pattern, (b) extent, (c) location and involved site, (d) associated focal abscess, and (e) swelling of the adjacent muscles. On plain radiographs, four cases showed streaky or mottled gas densities in the pelvis, three cases in the perineum, one case in the abdomen, and two cases in the thigh. On CT images, gas pattern was mottled and streaky appearance with swelling of the adjacent muscles. Gas shadows located in the extraperitoneal space in four cases, fascial layer in four cases, and subcutaneous layer in four cases. There were gas shadows in pelvic wall, perineum, abdominal wall, buttock, thigh, and scrotum. Focal low density lesion suggestive of focal abscess was not visualized. Plain radiography is useful for early diagnosis of the necrotizing fasciitis and CT is very useful for detection of precise location and extent of the disease. CT is also useful for differentiation of necrotizing fasciitis from focal abscess and cellulitis.

Porosity Prediction of Plain Weft Knitted Fabrics

Directory of Open Access Journals (Sweden)

Muhammad Owais Raza Siddiqui

2014-12-01

Full Text Available Wearing comfort of clothing is dependent on air permeability, moisture absorbency and wicking properties of fabric, which are related to the porosity of fabric. In this work, a plug-in is developed using Python script and incorporated in Abaqus/CAE for the prediction of porosity of plain weft knitted fabrics. The Plug-in is able to automatically generate 3D solid and multifilament weft knitted fabric models and accurately determine the porosity of fabrics in two steps. In this work, plain weft knitted fabrics made of monofilament, multifilament and spun yarn made of staple fibers were used to evaluate the effectiveness of the developed plug-in. In the case of staple fiber yarn, intra yarn porosity was considered in the calculation of porosity. The first step is to develop a 3D geometrical model of plain weft knitted fabric and the second step is to calculate the porosity of the fabric by using the geometrical parameter of 3D weft knitted fabric model generated in step one. The predicted porosity of plain weft knitted fabric is extracted in the second step and is displayed in the message area. The predicted results obtained from the plug-in have been compared with the experimental results obtained from previously developed models; they agreed well.

Gamma-ray multiplicity measurement of the spontaneous fission decay of 252Cf in a segmented HPGe/BGO detector array

Energy Technology Data Exchange (ETDEWEB)

Bleuel, D L; Bernstein, L A; Burke, J T; Gibelin, J; Heffner, M D; Mintz, J; Norman, E B; Phair, L; Scielzo, N D; Sheets, S A; Snyderman, N J; Stoyer, M A; Wiedeking, M

2008-04-23

Coincident {gamma} rays from a {sup 252}Cf source were measured using an array of six segmented high-purity germanium (HPGe) Clover detectors each enclosed by 16 bismuth-germanate (BGO) detectors. The detectors were arranged in a cubic pattern around a 1 {micro}Ci {sup 252}Cf source to cover a large solid angle for {gamma}-ray measurement with a reasonable reconstruction of the multiplicity. Neutron multiplicity was determined in certain cases by identifying the prompt {gamma} rays from individual fission fragment pairs. Multiplicity distributions from previous experiments and theoretical models were convolved with the response function of the array and compared to the present results. These results suggest a {gamma}-ray multiplicity spectrum broader than previous measurements and models, and provide no evidence of correlation with neutron multiplicity.

Sustainable Authorship in Plain Text using Pandoc and Markdown

Directory of Open Access Journals (Sweden)

Dennis Tenen

2014-03-01

Full Text Available In this tutorial, you will first learn the basics of Markdown—an easy to read and write markup syntax for plain text—as well as Pandoc, a command line tool that converts plain text into a number of beautifully formatted file types: PDF, .docx, HTML, LaTeX, slide decks, and more.1 With Pandoc as your digital typesetting tool, you can use Markdown syntax to add figures, a bibliography, formatting, and easily change citation styles from Chicago to MLA (for instance, all using plain text.

Plain ABDO X-rays: a waste of time?

Science.gov (United States)

2002-03-01

Plain abdominal radiographs are commonly requested for acute medical emergencies on patients with non-specific abdominal symptoms and signs. In this study, 131 plain abdominal radiographs performed on the day of admission were prospectively analysed by the research team. In only 16 cases (12 per cent) the reasons for requests conformed to the recommended guidelines by the Royal College of Radiologists. The reason for the request was stated in the case notes in only three cases. In 62 cases (47 per cent), there was no comment made on the film by the requesting clinician. There was a discrepancy in the interpretation of the radiograph between the clinician and the radiologist in 31 cases (24 per cent). The clinical management was influenced by plain abdominal radiographs in only nine cases (7 per cent). The researchers argue that most plain abdominal radiographs requested on acute medical emergencies are inappropriate. They suggest there is a need to ensure guidelines are followed to prevent unnecessary exposure of patients to radiation as well as preventing expenditure on irrelevant investigations.

Solar array flight dynamic experiment

Science.gov (United States)

Schock, Richard W.

1987-01-01

The purpose of the Solar Array Flight Dynamic Experiment (SAFDE) is to demonstrate the feasibility of on-orbit measurement and ground processing of large space structures' dynamic characteristics. Test definition or verification provides the dynamic characteristic accuracy required for control systems use. An illumination/measurement system was developed to fly on space shuttle flight STS-41D. The system was designed to dynamically evaluate a large solar array called the Solar Array Flight Experiment (SAFE) that had been scheduled for this flight. The SAFDE system consisted of a set of laser diode illuminators, retroreflective targets, an intelligent star tracker receiver and the associated equipment to power, condition, and record the results. In six tests on STS-41D, data was successfully acquired from 18 retroreflector targets and ground processed, post flight, to define the solar array's dynamic characteristic. The flight experiment proved the viability of on-orbit test definition of large space structures dynamic characteristics. Future large space structures controllability should be greatly enhanced by this capability.

The Applicability of Incoherent Array Processing to IMS Seismic Array Stations

Science.gov (United States)

Gibbons, S. J.

2012-04-01

The seismic arrays of the International Monitoring System for the CTBT differ greatly in size and geometry, with apertures ranging from below 1 km to over 60 km. Large and medium aperture arrays with large inter-site spacings complicate the detection and estimation of high frequency phases since signals are often incoherent between sensors. Many such phases, typically from events at regional distances, remain undetected since pipeline algorithms often consider only frequencies low enough to allow coherent array processing. High frequency phases that are detected are frequently attributed qualitatively incorrect backazimuth and slowness estimates and are consequently not associated with the correct event hypotheses. This can lead to missed events both due to a lack of contributing phase detections and by corruption of event hypotheses by spurious detections. Continuous spectral estimation can be used for phase detection and parameter estimation on the largest aperture arrays, with phase arrivals identified as local maxima on beams of transformed spectrograms. The estimation procedure in effect measures group velocity rather than phase velocity and the ability to estimate backazimuth and slowness requires that the spatial extent of the array is large enough to resolve time-delays between envelopes with a period of approximately 4 or 5 seconds. The NOA, AKASG, YKA, WRA, and KURK arrays have apertures in excess of 20 km and spectrogram beamforming on these stations provides high quality slowness estimates for regional phases without additional post-processing. Seven arrays with aperture between 10 and 20 km (MJAR, ESDC, ILAR, KSRS, CMAR, ASAR, and EKA) can provide robust parameter estimates subject to a smoothing of the resulting slowness grids, most effectively achieved by convolving the measured slowness grids with the array response function for a 4 or 5 second period signal. The MJAR array in Japan recorded high SNR Pn signals for both the 2006 and 2009 North Korea

Diagnostics of the BIOMASS feed array prototype

DEFF Research Database (Denmark)

Cappellin, Cecilia; Pivnenko, Sergey; Pontoppidan, Kennie Nybo

2013-01-01

The 3D reconstruction algorithm is applied to the prototype feed array of the BIOMASS synthetic aperture radar, recently measured at the DTU-ESA Spherical Near-Field Antenna Test Facility in Denmark. Careful analysis of the measured feed array data has shown that the test support structure...

Infrared measurements in defence application

CSIR Research Space (South Africa)

Mudau, AE

2011-03-01

Full Text Available the measurements and tests are done both in laboratory and field environments, it is important to understand and account for the influence of the environment on the measurement outcome. In addition, consistently disciplined measurement practices are required... stream_source_info Mudau_2011.pdf.txt stream_content_type text/plain stream_size 11031 Content-Encoding ISO-8859-1 stream_name Mudau_2011.pdf.txt Content-Type text/plain; charset=ISO-8859-1 Measurement...

Assessment of the Effect of Fruit (Apple and Plain Yoghurt Consumption on Plaque pH

Directory of Open Access Journals (Sweden)

Peyvand Moeiny

2017-09-01

Full Text Available Introduction: Nowadays, thanks to improvements in fruit yoghurt tastes, more tendencies are seen in their consumption especially among children. Therefore, their cariogenicity evaluation as healthy snacks is important. The goal of this study was the assessment of the consumption effect of two kinds of Iranian fruit (apple and plain yoghurts on dental plaque PH. Methods: In this experimental study, 10 healthy dentistry students were selected upon inclusion criteria. Plaque pH in the certain areas of the mouth was measured by microelectrode and digital pH meter. PH was measured at the baseline and intervals of 2, 5, 7, 10, 15, 20, 30, 40, 50 and 60 minutes after eating test products: fruit yoghurt (apple and plain Yoghurt. For positive control group, just the baseline PH and at intervals of 2 and 5 min after swishing with 10% sucrose solutions were recorded. The results were analyzed using repeated measures ANOVA. Results: Lowest pH was obtained after fruit yoghurt consumption followed by plain yoghurt and %10 sucrose solution and the plaque PH difference was significant (P=0.05. Furthermore, time duration which remained below the critical pH was longer after consuming fruit yoghurt. Conclusion: Both kinds of yoghurts were considered cariogenic since plaque pH drop below critical points. Average of plaque pH after consuming fruit yoghurt was significantly lower in almost all the time intervals

Water quality in the surficial aquifer near agricultural areas in the Delaware Coastal Plain, 2014

Science.gov (United States)

Fleming, Brandon J.; Mensch, Laura L.; Denver, Judith M.; Cruz, Roberto M.; Nardi, Mark R.

2017-07-27

The U.S. Geological Survey, in cooperation with the Delaware Department of Agriculture, developed a network of wells to monitor groundwater quality in the surficial aquifer of the Delaware Coastal Plain. Well-drained soils, a flat landscape, and accessible water in the Delaware Coastal Plain make for a productive agricultural setting. As such, agriculture is one of the largest industries in the State of Delaware. This setting enables the transport of chemicals from agriculture and other land uses to shallow groundwater. Efforts to mitigate nutrient transport to groundwater by the implementation of agricultural best management practices (BMPs) have been ongoing for several decades. To measure the effectiveness of BMPs on a regional scale, a network of 48 wells was designed to measure shallow groundwater quality (particularly nitrate) over time near agricultural land in the Delaware Coastal Plain. Water characteristics, major ions, nutrients, and dissolved gases were measured in groundwater samples collected from network wells during fall 2014. Wells were organized into three groups based on their geochemical similarity and these groups were used to describe nitrate and chloride concentrations and factors that affect the variability among the groups. The results from this study are intended to establish waterquality conditions in 2014 to enable comparison of future conditions and evaluate the effectiveness of agricultural BMPs on a regional scale.

Quality assessment of solar UV irradiance measured with array spectroradiometers

Science.gov (United States)

Egli, Luca; Gröbner, Julian; Hülsen, Gregor; Bachmann, Luciano; Blumthaler, Mario; Dubard, Jimmy; Khazova, Marina; Kift, Richard; Hoogendijk, Kees; Serrano, Antonio; Smedley, Andrew; Vilaplana, José-Manuel

2016-04-01

The reliable quantification of ultraviolet (UV) radiation at the earth's surface requires accurate measurements of spectral global solar UV irradiance in order to determine the UV exposure to human skin and to understand long-term trends in this parameter. Array spectroradiometers (ASRMs) are small, light, robust and cost-effective instruments, and are increasingly used for spectral irradiance measurements. Within the European EMRP ENV03 project "Solar UV", new devices, guidelines and characterization methods have been developed to improve solar UV measurements with ASRMs, and support to the end user community has been provided. In order to assess the quality of 14 end user ASRMs, a solar UV intercomparison was held on the measurement platform of the World Radiation Center (PMOD/WRC) in Davos, Switzerland, from 10 to 17 July 2014. The results of the blind intercomparison revealed that ASRMs, currently used for solar UV measurements, show a large variation in the quality of their solar UV measurements. Most of the instruments overestimate the erythema-weighted UV index - in particular at large solar zenith angles - due to stray light contribution in the UV-B range. The spectral analysis of global solar UV irradiance further supported the finding that the uncertainties in the UV-B range are very large due to stray light contribution in this wavelength range. In summary, the UV index may be detected by some commercially available ASRMs within 5 % compared to the world reference spectroradiometer, if well characterized and calibrated, but only for a limited range of solar zenith angles. Generally, the tested instruments are not yet suitable for solar UV measurements for the entire range between 290 and 400 nm under all atmospheric conditions.

Symmetric aluminum-wire arrays generate high-quality Z pinches at large array radii

International Nuclear Information System (INIS)

Sanford, T.W.; Mock, R.C.; Spielman, R.B.; Peterson, D.L.; Mosher, D.; Roderick, N.F.

1998-01-01

A Saturn-accelerator study of annular, aluminum-wire array, Z-pinch implosions, in the calculated high-wire-number plasma-shell regime [Phys. Rev. Lett. 77, 5063 (1996)], shows that the radiated x-ray pulse width increases from about 4 nsec to about 7 nsec, when the radius of the array is increased from 8.75 to 20 mm at a fixed array mass of 0.6 mg. Eulerian radiation- magnetohydrodynamic code (E-RMHC) simulations in the r-z plane suggest that this pulse-width increase with radius is due to the faster growth of the shell thickness (that arises from a two-stage development in the magnetic Rayleigh - Taylor instability) relative to the increase in the shell implosion velocity. Over the array radii explored, the measured peak total x-ray power of ∼40 TW and energy of ∼325 kJ show little change outside of a ±15% shot-to-shot fluctuation and are consistent with the E-RMHC simulations. Similarly, the measured peak K-shell (lines plus continuum) power of ∼8 TW and energy of ∼70 kJ show little change with radius. The minimal change in K-shell yield is in agreement with simple K-shell radiation scaling models that assume a fixed radial compression for all initial array radii. These results suggest that the improved uniformity provided by the large number of wires in the initial array reduces the disruptive effects of the Rayleigh - Taylor instability observed in small-wire-number imploding loads. copyright 1998 American Institute of Physics

Symmetric aluminum-wire arrays generate high-quality Z pinches at large array radii

Science.gov (United States)

Sanford, T. W. L.; Mock, R. C.; Spielman, R. B.; Peterson, D. L.; Mosher, D.; Roderick, N. F.

1998-10-01

A Saturn-accelerator study of annular, aluminum-wire array, Z-pinch implosions, in the calculated high-wire-number plasma-shell regime [Phys. Rev. Lett. 77, 5063 (1996)], shows that the radiated x-ray pulse width increases from about 4 nsec to about 7 nsec, when the radius of the array is increased from 8.75 to 20 mm at a fixed array mass of 0.6 mg. Eulerian radiation- magnetohydrodynamic code (E-RMHC) simulations in the r-z plane suggest that this pulse-width increase with radius is due to the faster growth of the shell thickness (that arises from a two-stage development in the magnetic Rayleigh-Taylor instability) relative to the increase in the shell implosion velocity. Over the array radii explored, the measured peak total x-ray power of ˜40 TW and energy of ˜325 kJ show little change outside of a ±15% shot-to-shot fluctuation and are consistent with the E-RMHC simulations. Similarly, the measured peak K-shell (lines plus continuum) power of ˜8 TW and energy of ˜70 kJ show little change with radius. The minimal change in K-shell yield is in agreement with simple K-shell radiation scaling models that assume a fixed radial compression for all initial array radii. These results suggest that the improved uniformity provided by the large number of wires in the initial array reduces the disruptive effects of the Rayleigh-Taylor instability observed in small-wire-number imploding loads.

Quantitative analysis of bowel gas by plain abdominal radiograph combined with computer image processing

International Nuclear Information System (INIS)

Gao Yan; Peng Kewen; Zhang Houde; Shen Bixian; Xiao Hanxin; Cai Juan

2003-01-01

Objective: To establish a method for quantitative analysis of bowel gas by plain abdominal radiograph and computer graphics. Methods: Plain abdominal radiographs in supine position from 25 patients with irritable bowel syndrome (IBS) and 20 health controls were studied. A gastroenterologist and a radiologist independently conducted the following procedure on each radiograph. After the outline of bowel gas was traced by axe pen, the radiograph was digitized by a digital camera and transmitted to the computer with Histogram software. The total gas area was determined as the pixel value on images. The ratio of the bowel gas quantity to the pixel value in the region surrounded by a horizontal line tangential to the superior pubic symphysis margin, a horizontal line tangential to the tenth dorsal vertebra inferior margin, and the lateral line tangential to the right and left anteriosuperior iliac crest, was defined as the gas volume score (GVS). To examine the sequential reproducibility, a second plain abdominal radiograph was performed in 5 normal controls 1 week later, and the GVS were compared. Results: Bowel gas was easily identified on the plain abdominal radiograph. Both large and small intestine located in the selected region. Both observers could finish one radiographic measurement in less than 10 mins. The correlation coefficient between the two observers was 0.986. There was no statistical difference on GVS between the two sequential radiographs in 5 health controls. Conclusion: Quantification of bowel gas based on plain abdominal radiograph and computer is simple, rapid, and reliable

Array capabilities and future arrays

International Nuclear Information System (INIS)

Radford, D.

1993-01-01

Early results from the new third-generation instruments GAMMASPHERE and EUROGAM are confirming the expectation that such arrays will have a revolutionary effect on the field of high-spin nuclear structure. When completed, GAMMASHPERE will have a resolving power am order of magnitude greater that of the best second-generation arrays. When combined with other instruments such as particle-detector arrays and fragment mass analysers, the capabilites of the arrays for the study of more exotic nuclei will be further enhanced. In order to better understand the limitations of these instruments, and to design improved future detector systems, it is important to have some intelligible and reliable calculation for the relative resolving power of different instrument designs. The derivation of such a figure of merit will be briefly presented, and the relative sensitivities of arrays currently proposed or under construction presented. The design of TRIGAM, a new third-generation array proposed for Chalk River, will also be discussed. It is instructive to consider how far arrays of Compton-suppressed Ge detectors could be taken. For example, it will be shown that an idealised open-quote perfectclose quotes third-generation array of 1000 detectors has a sensitivity an order of magnitude higher again than that of GAMMASPHERE. Less conventional options for new arrays will also be explored

Detailed Diagnostics of the BIOMASS Feed Array Prototype

DEFF Research Database (Denmark)

Cappellin, C.; Pivnenko, Sergey; Pontoppidan, K.

2013-01-01

of the array had a significant influence on the measured feed pattern. The 3D reconstruction and further post-processing is therefore applied both to the feed array measured data, and a set of simulated data generated by the GRASP software which replicate the series of measurements. The results...

Improved linear pyroelectric IR detector arrays

International Nuclear Information System (INIS)

Twiney, R.C.; Robinson, M.K.; Porter, S.G.

1987-01-01

Good agreement has been found between theoretical models and measured performance for a range of array geometries. A 64-element 80 x 140-micron element array with integral MOSFET IC buffer preamplifiers shows improved source voltage uniformity, a J-FET buffered array, and low-frequency specific detectivity (SD) of 1.7 x 10 to the 8th cm sq rt Hz/W at 40 Hz. The MOSFET array shows reduced degradation of SD at high temperatures, retaining an SD of not less than 1 x 10 to the 8th cm sq rt Hz/W at +70 C across much of the band. A 64-element array has been designed using onboard multiplexers, thus greatly reducing the connections needed to run the array

A Framework for Speech Enhancement with Ad Hoc Microphone Arrays

DEFF Research Database (Denmark)

Tavakoli, Vincent Mohammad; Jensen, Jesper Rindom; Christensen, Mads Græsbøll

2016-01-01

Speech enhancement is vital for improved listening practices. Ad hoc microphone arrays are promising assets for this purpose. Most well-established enhancement techniques with conventional arrays can be adapted into ad hoc scenarios. Despite recent efforts to introduce various ad hoc speech...... enhancement apparatus, a common framework for integration of conventional methods into this new scheme is still missing. This paper establishes such an abstraction based on inter and intra sub-array speech coherencies. Along with measures for signal quality at the input of sub-arrays, a measure of coherency...... is proposed both for sub-array selection in local enhancement approaches, and also for selecting a proper global reference when more than one sub-array are used. Proposed methods within this framework are evaluated with regard to quantitative and qualitative measures, including array gains, the speech...

Using Radon and Radium isotopes to trace submarine groundwater discharge in Yilan Plain, Taiwan

Science.gov (United States)

Huang, Chun-Kai; Su, Chih-Chieh

2015-04-01

The Yilan Plain which located in the northeast Taiwan was selected for submarine groundwater discharge (SGD) study. The geomorphic and climatic conditions induce lush rain drenched mountains and create abundant groundwater resource in the Yilan Plain. The annual precipitation in 2014 is 2025 mm with most of the precipitation concentrated on autumn (from September to November). In this study, radon and radium isotopes are used as tracers for SGD survey. The 224Ra (t1/2 =3.6 days) was measured by a delayed coincidence counter (RaDeCC). The 222Rn (t1/2 =3.8 days) was measured by RAD-7 equipped with RAD H2O and RAD AQUA system. The river-water samples were collected from the main stream of Lanyang River and its tributaries from upstream to river mouth. The spring-water samples were collected at 8 sites in April, July and October 2014. Ten surface seawater samples along the coastline of the Yilan Plain were collected in August 2014. Our results show the activities of 222Rn and 224Ra in springs ranging from 3400 to 30850 Bq/m3 and 0.02 to 0.29 Bq/m3, and there are no significant differences between wet and dry seasons. Unexpectedly, the springs are characterized with high 222Rn and low 224Ra activities. For river samples, the activities of 224Ra in downstream and river mouth (0.18 to 1.48 Bq/m3) are higher than upstream (0 to 0.3 Bq/m3). The average activity of 224Ra in downstream samples which collected in April (0.98 Bq/m3) has the highest value than other seasons (0.41-0.51 Bq/m3). In coastal seawater, the activities of 222Rn and 224Ra ranged from 0 to 366 Bq/m3 and 0.10 to 1.14 Bq/m3 in August 2014. In summary, this study points out in some coastal regions of the Yilan Plain, where without riverine input, have high 222Rn and 224Ra activities in seawater. We suggest the SGD plays an important role on land-sea exchange along the coastline of the Yilan Plain. Compare with the spring water samples, the 224Ra activities in coastal seawater are 3-4 times higher than

Measurement and analysis of flow wall shear stress in an interior subchannel of triangular array rods

International Nuclear Information System (INIS)

Fakori-Monazah, M.R.; Todreas, N.E.

1977-08-01

A simulated model of triangular array rods with pitch to diameter ratio of 1.10 (as a test section) and air as the fluid flow was used to study the LMFBR hydraulic parameters. The wall shear stress distribution around the rod periphery, friction factors, static pressure distributions and turbulence intensity corresponding to various Reynolds numbers ranging from 4140 to 36170 in the central subchannel were measured. Various approaches for measurement of wall shear stress were compared. The measurement was performed using the Preston tube technique with the probe outside diameter equal to 0.014 in

Radiocarbon dating of sediment cores from Hachinohe, the Kamikita Plain

International Nuclear Information System (INIS)

Hitoki, Eri; Nakamura, Toshio; Matsumoto, Yui; Tsuji, Sei-ichiro; Fujine, Hisashi

2013-01-01

We investigated stratigraphy and chronology by analyses of Holocene sediments and radiocarbon dating of sediment cores from the Kamikita Plain. On the Kamikita Plain, which faces the Pacific coast of Northeast Japan, marine and fluvial terraces covered with tephras derived from Towada and Hakkoda volcanoes are well developed. We clarified that Towada Chuseri tephra and fluvial deposits consisted of volcanic sediments influenced an alluvial depositional system in the Kamikita Plain after a maximum of the Jomon Transgression. (author)

Measuring the homogeneity of Bi(2223)/Ag tapes by four-probe method and a Hall probe array

International Nuclear Information System (INIS)

Kovac, P.

1999-01-01

The nature of the BSCCO compound and application of the powder-in-tube technique usually lead to non-uniform quality across and/or along the ceramic fibres and finally to variations in the critical current and its irregular distribution in the Bi(2223)/Ag tape. Therefore, the gliding four-probe method and contactless field monitoring measurements have been used for homogeneity studies. The gliding potential contacts moved along the tape surface and a sensitive system based on an integrated Hall probe array containing 16 or 19 in-line probes supported by PC-compatible electronics with software allowed us to make a comparison of contact and contactless measurements at any elements of Bi(2223)/Ag sample. The results of both methods show very good correlation and the possibility of using a sensitive Hall probe array for monitoring the final quality of Bi(2223)/Ag tapes. (author)

Clinical and Plain Radiograph Pattern of Joint Dislocations and ...

African Journals Online (AJOL)

Plain radiograph is an integral part of early assessment of patients' evaluation, though newer imaging modalities such as magnetic resonance imaging (MRI), ... Conclusion: The shoulder joint is the most frequently dislocated and a conventional plain radiograph is still valuable as a first line investigative modality in ...

Analysis of High Plains Resource Risk and Economic Impacts

Energy Technology Data Exchange (ETDEWEB)

Tidwell, Vincent C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vargas, Vanessa N [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Shannon M [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dealy, Bern Caudill [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Shaneyfelt, Calvin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Smith, Braeton James [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Moreland, Barbara Denise [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-04-01

The importance of the High Plains Aquifer is broadly recognized as is its vulnerability to continued overuse. T his study e xplore s how continued depletions of the High Plains Aquifer might impact both critical infrastructure and the economy at the local, r egional , and national scale. This analysis is conducted at the county level over a broad geographic region within the states of Kansas and Nebraska. In total , 140 counties that overlie the High Plains Aquifer in these two states are analyzed. The analysis utilizes future climate projections to estimate crop production. Current water use and management practices are projected into the future to explore their related impact on the High Plains Aquifer , barring any changes in water management practices, regulat ion, or policy. Finally, the impact of declining water levels and even exhaustion of groundwater resources are projected for specific sectors of the economy as well as particular elements of the region's critical infrastructure.

A participatory approach of flood vulnerability assessment in the Banat Plain, Romania

Science.gov (United States)

Balteanu, Dan; Costache, Andra; Sima, Mihaela; Dumitrascu, Monica; Dragota, Carmen; Grigorescu, Ines

2014-05-01

The Banat Plain (western Romania) is a low, alluvial plain affected by neotectonic subsidence movements, being a critical region in terms of exposure to floods. The latest extreme event was the historic floods occcured in the spring of 2005, which caused significant economic damage in several rural communities. The response to 2005 floods has highlighted a number of weaknesses in the management of hazards, such as the deficiencies of the early warning system, people awareness or the inefficiency of some mitigation measures, besides the past structural measures which are obsolete. For a better understanding of the local context of vulnerability and communities resilience to floods, the quantitative assessment of human vulnerability to floods was supplemented with a participatory research, in which there were involved five rural settlements from the Banat Plain (comprising 15 villages and a population of over 12,000 inhabitants). Thus, in the spring of 2013, a questionnaire-based survey was conducted in approx. 100 households of the affected communities and structured interviews were held with local authorities, in the framework of VULMIN project, funded by the Ministry of National Education. The questionnaire was designed based on a pilot survey conducted in 2005, several months after the flood, and was focused on two major issues: a) perception of the local context of vulnerability to environmental change and extreme events; b) perception of human vulnerability to floods (personal experience, post-disaster rehabilitation, awareness, worrying and opinion on the measures aimed to prevent and mitigate the effects of flooding). The results were correlated with a number of specific variables of the households included in the sample, such as: household structure; income source; income level; location of the dwelling in relation to floodplains. In this way, we were able to draw general conclusions about the way in which local people perceive the extreme events, such as

Characterization of Kerfless Linear Arrays Based on PZT Thick Film.

Science.gov (United States)

Zawada, Tomasz; Bierregaard, Louise Moller; Ringgaard, Erling; Xu, Ruichao; Guizzetti, Michele; Levassort, Franck; Certon, Dominique

2017-09-01

Multielement transducers enabling novel cost-effective fabrication of imaging arrays for medical applications have been presented earlier. Due to the favorable low lateral coupling of the screen-printed PZT, the elements can be defined by the top electrode pattern only, leading to a kerfless design with low crosstalk between the elements. The thick-film-based linear arrays have proved to be compatible with a commercial ultrasonic scanner and to support linear array beamforming as well as phased array beamforming. The main objective of the presented work is to investigate the performance of the devices at the transducer level by extensive measurements of the test structures. The arrays have been characterized by several different measurement techniques. First, electrical impedance measurements on several elements in air and liquid have been conducted in order to support material parameter identification using the Krimholtz-Leedom-Matthaei model. It has been found that electromechanical coupling is at the level of 35%. The arrays have also been characterized by a pulse-echo system. The measured sensitivity is around -60 dB, and the fractional bandwidth is close to 60%, while the center frequency is about 12 MHz over the whole array. Finally, laser interferometry measurements have been conducted indicating very good displacement level as well as pressure. The in-depth characterization of the array structure has given insight into the performance parameters for the array based on PZT thick film, and the obtained information will be used to optimize the key parameters for the next generation of cost-effective arrays based on piezoelectric thick film.

Remote online process measurements by a fiber optic diode array spectrometer

International Nuclear Information System (INIS)

Van Hare, D.R.; Prather, W.S.; O'Rourke, P.E.

1986-01-01

The development of remote online monitors for radioactive process streams is an active research area at the Savannah River Laboratory (SRL). A remote offline spectrophotometric measurement system has been developed and used at the Savannah River Plant (SRP) for the past year to determine the plutonium concentration of process solution samples. The system consists of a commercial diode array spectrophotometer modified with fiber optic cables that allow the instrument to be located remotely from the measurement cell. Recently, a fiber optic multiplexer has been developed for this instrument, which allows online monitoring of five locations sequentially. The multiplexer uses a motorized micrometer to drive one of five sets of optical fibers into the optical path of the instrument. A sixth optical fiber is used as an external reference and eliminates the need to flush out process lines to re-reference the spectrophotometer. The fiber optic multiplexer has been installed in a process prototype facility to monitor uranium loading and breakthrough of ion exchange columns. The design of the fiber optic multiplexer is discussed and data from the prototype facility are presented to demonstrate the capabilities of the measurement system

Radio monitoring of the Sozh-river flood plain

International Nuclear Information System (INIS)

Kuznetsova, V.A.; Generalova, V.A.; Kol'nenkov, V.P.; Glaz, A.S.

2001-01-01

Periodic radiation monitoring supervision is the important parameter of the radioactivity level time control with reference to concrete landscapes, estimation and their ecological radiochemistry conditions forecast in order to accept practical measures for the risk radiation danger reduction. The early monitoring supervision was carried out in the area of radioactive anomalies in Sozh-river flood plain. The new data received in 1998 and 2000 are cited below. The radiation situation of the last landscape appropriating to conditions in central and near terrace Sozh-river flood plain, more than in 10 years, is nowadays characterized by the data of the structure of Veprin one. In coastal flood plain the maximal radioactivity is dated to meadow vegetable layer in downturn of relief or to humus horizon of actual soil on coastal shaft. In central flood plain it remains rather high with the tendency of accumulation in meliorative channels, which are nowadays strongly overgrown, in 1,6-1,9 times exceeding earlier supervision. Down the Sozh near the village Gronovo in 1988 the level of gamma activity meadow vegetable layer changed. Radioactive situation is low here nowadays: on meadow vegetable layer almost in 5 times lower than former one. It is explained by the active hydro mode snow melt flood streams at the abrupt bend of Sozh channel, resulting in meadows washing and silt material washout. The deepening of Cs-137 reaches 0,20 m and connects with the accumulation of isotope in the top part of humus horizon where it is fixed in the fixed form. Monitoring supervision on radio strontium in the section of Sozh-river flood plain near the village Gronovo shows, that in 1995 its maximal concentration is observed in humusided loamy sand under meadow vegetable layer; the main mass of isotope - up to 80 % - was concentrated in the top 30-sm layer. It is remarkable, that with depth, reducing the contents almost twice and not being marked in underlaying sands, this isotope

Woodville Karst Plain, North Florida

OpenAIRE

2006-01-01

Map showing the largest mapped underwater cave systems and conduit flow paths confirmed by tracer testing relative to surface streams, sinkholes and potentiometric surface of the Florida aquifer in the Woodville Karst Plain, Florida

Symmetric aluminum-wire arrays generate high-quality Z pinches at large array radii

Energy Technology Data Exchange (ETDEWEB)

Sanford, T.W.; Mock, R.C.; Spielman, R.B. [Sandia National Laboratories, P.O. Box 5800, Albuquerque, New Mexico 87185 (United States); Peterson, D.L. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545-0010 (United States); Mosher, D. [Naval Research Laboratory, Pulsed Power Physics Branch, Washington, DC 20375 (United States); Roderick, N.F. [University of New Mexico, Albuquerque, New Mexico 87131 (United States)

1998-10-01

A Saturn-accelerator study of annular, aluminum-wire array, Z-pinch implosions, in the calculated high-wire-number plasma-shell regime [Phys. Rev. Lett. {bold 77}, 5063 (1996)], shows that the radiated x-ray pulse width increases from about 4 nsec to about 7 nsec, when the radius of the array is increased from 8.75 to 20 mm at a fixed array mass of 0.6 mg. Eulerian radiation- magnetohydrodynamic code (E-RMHC) simulations in the r-z plane suggest that this pulse-width increase with radius is due to the faster growth of the shell thickness (that arises from a two-stage development in the magnetic Rayleigh{endash}Taylor instability) relative to the increase in the shell implosion velocity. Over the array radii explored, the measured peak total x-ray power of {approximately}40 TW and energy of {approximately}325 kJ show little change outside of a {plus_minus}15{percent} shot-to-shot fluctuation and are consistent with the E-RMHC simulations. Similarly, the measured peak {ital K}-shell (lines plus continuum) power of {approximately}8 TW and energy of {approximately}70 kJ show little change with radius. The minimal change in {ital K}-shell yield is in agreement with simple {ital K}-shell radiation scaling models that assume a fixed radial compression for all initial array radii. These results suggest that the improved uniformity provided by the large number of wires in the initial array reduces the disruptive effects of the Rayleigh{endash}Taylor instability observed in small-wire-number imploding loads. {copyright} {ital 1998 American Institute of Physics.}

Precision Measurements of Wind Turbine Noise using a Large Aperture Microphone Array

DEFF Research Database (Denmark)

Bradley, Stuart; Mikkelsen, Torben Krogh; Hünerbein, Sabine Von

2016-01-01

Experiments are described with a large microphone array (40 m scale) recording wind turbine noise. The array comprised 42 purpose-designed low-noise microphones simultaneously sampled at 20 kHz. Very high quality, fast, meteorological profile data was available from nearby 80 m masts and from the...

18 CFR 801.8 - Flood plain management and protection.

Science.gov (United States)

2010-04-01

... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Flood plain management and protection. 801.8 Section 801.8 Conservation of Power and Water Resources SUSQUEHANNA RIVER BASIN COMMISSION GENERAL POLICIES § 801.8 Flood plain management and protection. (a) Periodic inundation of lands...

Probabilistic health risk assessment for arsenic intake through drinking groundwater in Taiwan's Pingtung Plain

Science.gov (United States)

Liang, C. P.; Chen, J. S.

2017-12-01

An abundant and inexpensive supply of groundwater is used to meet drinking, agriculture and aquaculture requirements of the residents in the Pingtung Plain. Long-term groundwater quality monitoring data indicate that the As content in groundwater in the Pingtung Plain exceeds the maximum level of 10 g/L recommended by the World Health Organization (WHO). The situation is further complicated by the fact that only 46.89% of population in the Pingtung Plain has been served with tap water, far below the national average of 92.93%. Considering there is a considerable variation in the measured concentrations, from below the detection limit (consumption rate and body weight of the individual, the conventional approach to conducting a human health risk assessment may be insufficient for health risk management. This study presents a probabilistic risk assessment for inorganic As intake through the consumption of the drinking groundwater by local residents in the Pingtung Plain. The probabilistic risk assessment for inorganic As intake through the consumption of the drinking groundwater is achieved using Monte Carlo simulation technique based on the hazard quotient (HQ) and target cancer risk (TR) established by the U.S. Environmental Protection Agency. This study demonstrates the importance of the individual variability of inorganic As intake through drinking groundwater consumption when evaluating a high exposure sub-group of the population who drink high As content groundwater.

Measurement of the point spread function of a pixelated detector array

Energy Technology Data Exchange (ETDEWEB)

Ritzer, Christian; Hallen, Patrick; Schug, David; Schulz, Volkmar [Department of Physics of Molecular Imaging Systems, Institute for Experimental Molecular Imaging, RWTH Aachen University, Aachen (Germany)

2015-05-18

In order to further understand the PET/MRI scanner of our group, we measured the point spread function of a preclinical scintillation crystal array with a pitch of 1 mm and a total size of 30 mm ~ 30 mm ~ 12 mm. It is coupled via a lightguide to a dSiPM from Philips Digital Photon Counting, used on the TEK-setup. Crystal identification is done with a centre of gravity algorithm and the whole data analysis is performed with the same processing software as for the PET insert, giving comparable results. The beam is created with a 22 NA-Point-Source and a lead collimator, with 0.5 mm bore diameter. The algorithm sorted 62 % of the coincidences into the correct crystal.

Measurement of the point spread function of a pixelated detector array

International Nuclear Information System (INIS)

Ritzer, Christian; Hallen, Patrick; Schug, David; Schulz, Volkmar

2015-01-01

In order to further understand the PET/MRI scanner of our group, we measured the point spread function of a preclinical scintillation crystal array with a pitch of 1 mm and a total size of 30 mm ~ 30 mm ~ 12 mm. It is coupled via a lightguide to a dSiPM from Philips Digital Photon Counting, used on the TEK-setup. Crystal identification is done with a centre of gravity algorithm and the whole data analysis is performed with the same processing software as for the PET insert, giving comparable results. The beam is created with a 22 NA-Point-Source and a lead collimator, with 0.5 mm bore diameter. The algorithm sorted 62 % of the coincidences into the correct crystal.

Research on High-Precision, Low Cost Piezoresistive MEMS-Array Pressure Transmitters Based on Genetic Wavelet Neural Networks for Meteorological Measurements

Directory of Open Access Journals (Sweden)

Jiahong Zhang

2015-05-01

Full Text Available This paper provides a novel and effective compensation method by improving the hardware design and software algorithm to achieve optimization of piezoresistive pressure sensors and corresponding measurement systems in order to measure pressure more accurately and stably, as well as to meet the application requirements of the meteorological industry. Specifically, GE NovaSensor MEMS piezoresistive pressure sensors within a thousandth of accuracy are selected to constitute an array. In the versatile compensation method, the hardware utilizes the array of MEMS pressure sensors to reduce random error caused by sensor creep, and the software adopts the data fusion technique based on the wavelet neural network (WNN which is improved by genetic algorithm (GA to analyze the data of sensors for the sake of obtaining accurate and complete information over the wide temperature and pressure ranges. The GA-WNN model is implemented in hardware by using the 32-bit STMicroelectronics (STM32 microcontroller combined with an embedded real-time operating system µC/OS-II to make the output of the array of MEMS sensors be a direct digital readout. The results of calibration and test experiments clearly show that the GA-WNN technique can be effectively applied to minimize the sensor errors due to the temperature drift, the hysteresis effect and the long-term drift because of aging and environmental changes. The maximum error of the low cost piezoresistive MEMS-array pressure transmitter proposed by us is within 0.04% of its full-scale value, and it can satisfy the meteorological pressure measurement.

Fundamentals of ultrasonic phased arrays

CERN Document Server

Schmerr, Lester W

2014-01-01

This book describes in detail the physical and mathematical foundations of ultrasonic phased array measurements.?The book uses linear systems theory to develop a comprehensive model of the signals and images that can be formed with phased arrays. Engineers working in the field of ultrasonic nondestructive evaluation (NDE) will find in this approach a wealth of information on how to design, optimize and interpret ultrasonic inspections with phased arrays. The fundamentals and models described in the book will also be of significant interest to other fields, including the medical ultrasound and

Antifriction coating of Cu-Fe-Al-Pb system for plain bearings

Science.gov (United States)

Kotenkov, Pavel; Kontsevoi, Yurii; Mejlakh, Anna; Pastukhov, Eduard; Shubin, Alexey; Goyda, Eduard; Sipatov, Ivan

2017-09-01

Aluminium, copper and their compounds are used in common as basis for antifriction coatings of plain bearings. Antifriction testing of plain bearings (based on Al and Cu) made by leading automotive manufacturers from Germany, Japan, USA, United Kingdom and Russia were carried out to make judicious selection of basis for development of new antifriction material. Testing was carried out using friction machine. It was defined that materials based on Cu provide better durability and robustness of plain bearings in comparison with Al based ones. The new antifriction composite coatings based on copper were developed taking into account the requirements specified for plain bearings of internal-combustion engine. Pilot samples of plain bearings with antifriction coatings of Cu-Fe-Al-Pb system were produced. The antifriction composite having Cu-5Fe-5Al5Fe2-10Pb (mass %) composition has demonstrated low friction factor and high wear-resistance. Metallographic analysis of pilot samples was carried out by means of optical and scanning electron microscopy.

Shallow velocity structure of Stromboli Volcano, Italy, derived from small-aperture array measurements of Strombolian tremor

Science.gov (United States)

Chouet, B.; De Luca, G.; Milana, G.; Dawson, P.; Martini, M.; Scarpa, R.

1998-01-01

The properties of the tremor wave field at Stromboli are analyzed using data from small-aperture arrays of short-period seismometers deployed on the north flank of the volcano. The seismometers are configued in two semi-circular arrays with radii of 60 and 150 m and a linear array with length of 600 m. The data are analyzed using a spatiotemporal correlation technique specifically designed for the study of the stationary stochastic wave field of Rayleigh and Love waves generated by volcanic activity and by scattering sources distributed within the island. The correlation coefficients derived as a function of frequency for the three components of motion clearly define the dispersion characteristics for both Rayleigh and Love waves. Love and Rayleigh waves contribute 70% and 30%, respectively, of the surface-wave power. The phase velocities of Rayleigh waves range from 1000 m/sec at 2 Hz to 350 m/sec at 9 Hz, and those for Love waves range from 700 to 400 m/sec over the same frequency band. These velocities are similar to those measured near Puu Oo on the east rift of Kilauea Volcano, Hawaii, although the dispersion characteristics of Rayleigh waves at Stromboli show a stronger dependence on frequency. Such low velocities are consistent with values expected for densely cracked solidified basalt. The dispersion curves are inverted for a velocity model beneath the arrays, assuming those dispersions represent the fundamental modes of Rayleigh and Love waves.

49 CFR 215.107 - Defective plain bearing box: General.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective plain bearing box: General. 215.107... Suspension System § 215.107 Defective plain bearing box: General. A railroad may not place or continue in... the bearing; or (2) Have a detrimental effect on the lubrication of the journal and the bearings. ...

High-performance plain bearings for diesel engines. Hochleistungs-Gleitlager fuer Dieselmotoren

Energy Technology Data Exchange (ETDEWEB)

Schmidt, R.M.; Mathias, M.; Herrmann, B. (MTU, Friedrichshafen (Germany))

1992-01-01

The crankshaft bearings are among the most highly stressed engine components. Conventional plain bearings no longer fulfill the requirements of modern high-performance diesel engines. Introduction of the 'Sputter' technology, as a method of anti friction layer application, opened new perspectives in the field of plain bearing manufacture. In this presentation it is intended to compare various types of plain bearings and to demonstrate operation-oriented bearing testing. (orig.).

Health Needs Assessment of Plain Populations in Lancaster County, Pennsylvania.

Science.gov (United States)

Miller, Kirk; Yost, Berwood; Abbott, Christina; Thompson, Scottie; Dlugi, Emily; Adams, Zachary; Schulman, Meryl; Strauss, Nicole

2017-02-01

We performed a health needs assessment for three Plain communities in Lancaster County, Pennsylvania from a random sample of households. Compared with the general population of adults, Plain respondents were more likely to be married, to have children, and they had large families; they were more likely to drink well water, to eat fruit and vegetables, to drink raw milk, and to live on a farm. Plain respondents had better physical and mental health and were less likely to have been diagnosed with various medical conditions compared with the general population of adults in Lancaster County but Old Order Mennonite respondents were more likely to have been diagnosed compared with Old Order Amish respondents. Plain respondents usually have a regular doctor and often receive preventive care but Old Order Mennonite respondents were more likely to have a regular doctor, to receive preventive care, to have had their children vaccinated, and to receive routine dental care compared with Old Order Amish respondents. Despite their relative geographic and genetic isolation, and despite the small, relative differences noted, the health of Plain communities in Lancaster County is similar to that of other adults in the County.

Isolated syndesmotic injury in acute ankle trauma: Comparison of plain film radiography with 3 T MRI

International Nuclear Information System (INIS)

Schoennagel, B.P.; Karul, M.; Avanesov, M.; Bannas, P.; Gold, G.; Großterlinden, L.G.; Rupprecht, M.; Adam, G.; Yamamura, J.

2014-01-01

Highlights: • Isolated syndesmotic injury is a frequent finding after acute ankle trauma. • Cut-off values and accuracy of plain film radiograph measurements were determined. • The TFCS and the MCS have the potential to detect isolated syndesmotic injury. • Appropriate cut-off values allow detection of isolated syndesmotic injury. • Only MRI reveals severity of isolated syndesmotic injury and concomitant injuries. - Abstract: Objectives: To determine cut-off values and the accuracy of plain film measurements for the detection of isolated syndesmotic injury after acute ankle trauma and to investigate MRI findings of concomitant ankle injury. Methods: Eighty-four consecutive patients with absent fracture in plain film radiographs were prospectively evaluated for isolated syndesmotic injury after acute ankle trauma. The tibiofibular clear space (TFCS), the tibiofibular overlap (TFO), and the medial clear space (MCS) were independently assessed in plain radiographs by two readers. MRI performed at 3 T within 24 h served as the reference standard. MRI was evaluated for syndesmotic injury, using a four-scale grading system (0 = normal syndesmosis, 1a = periligamentous edema, 1b = intraligamentous edema, 2 = partial rupture, 3 = complete rupture), and for concomitant ankle injury. Inter-observer variability for x-ray measurements was assessed using Bland–Altman diagrams. ROC analyses were performed to determine cut-off values and sensitivity and specificity for TFCS, TFO, and MCS. Results: Eleven of 84 patients (13.1%) revealed syndesmotic injury (Grade 2 or 3) according to MRI. Between patients with and without syndesmotic injury significantly different measurements were obtained for TFCS (p = 0.003) and MCS (p = 0.04). ROC derived cut-off values were 5.3 mm for TFCS, 2.8 mm for TFO, and 2.8 mm for MCS. Sensitivity and specificity was 82% and 75% for TFCS, 36% and 78% for TFO, and 73% and 59% for MCS. The bias and limits of agreement were −0.04 mm and [−1

Isolated syndesmotic injury in acute ankle trauma: Comparison of plain film radiography with 3 T MRI

Energy Technology Data Exchange (ETDEWEB)

Schoennagel, B.P., E-mail: b.schoennagel@uke.uni-hamburg.de [Department of Diagnostic and Interventional Radiology, University Medical Center Hamburg-Eppendorf, Martinistraße 52, 20246 Hamburg (Germany); Karul, M.; Avanesov, M.; Bannas, P.; Gold, G. [Department of Diagnostic and Interventional Radiology, University Medical Center Hamburg-Eppendorf, Martinistraße 52, 20246 Hamburg (Germany); Großterlinden, L.G. [Department of Trauma-, Hand- and Reconstructive Surgery, University Medical Center Hamburg-Eppendorf, Martinistraße 52, 20246 Hamburg (Germany); Rupprecht, M. [Department of Pediatric Orthopedics, Children' s Hospital Hamburg-Altona, Bleickenallee 38, 22763 Hamburg (Germany); Adam, G.; Yamamura, J. [Department of Diagnostic and Interventional Radiology, University Medical Center Hamburg-Eppendorf, Martinistraße 52, 20246 Hamburg (Germany)

2014-10-15

Highlights: • Isolated syndesmotic injury is a frequent finding after acute ankle trauma. • Cut-off values and accuracy of plain film radiograph measurements were determined. • The TFCS and the MCS have the potential to detect isolated syndesmotic injury. • Appropriate cut-off values allow detection of isolated syndesmotic injury. • Only MRI reveals severity of isolated syndesmotic injury and concomitant injuries. - Abstract: Objectives: To determine cut-off values and the accuracy of plain film measurements for the detection of isolated syndesmotic injury after acute ankle trauma and to investigate MRI findings of concomitant ankle injury. Methods: Eighty-four consecutive patients with absent fracture in plain film radiographs were prospectively evaluated for isolated syndesmotic injury after acute ankle trauma. The tibiofibular clear space (TFCS), the tibiofibular overlap (TFO), and the medial clear space (MCS) were independently assessed in plain radiographs by two readers. MRI performed at 3 T within 24 h served as the reference standard. MRI was evaluated for syndesmotic injury, using a four-scale grading system (0 = normal syndesmosis, 1a = periligamentous edema, 1b = intraligamentous edema, 2 = partial rupture, 3 = complete rupture), and for concomitant ankle injury. Inter-observer variability for x-ray measurements was assessed using Bland–Altman diagrams. ROC analyses were performed to determine cut-off values and sensitivity and specificity for TFCS, TFO, and MCS. Results: Eleven of 84 patients (13.1%) revealed syndesmotic injury (Grade 2 or 3) according to MRI. Between patients with and without syndesmotic injury significantly different measurements were obtained for TFCS (p = 0.003) and MCS (p = 0.04). ROC derived cut-off values were 5.3 mm for TFCS, 2.8 mm for TFO, and 2.8 mm for MCS. Sensitivity and specificity was 82% and 75% for TFCS, 36% and 78% for TFO, and 73% and 59% for MCS. The bias and limits of agreement were −0.04 mm and [−1

A LSO scintillator array for a PET detector module with depth of interaction measurement

International Nuclear Information System (INIS)

Huber, J.S.; Moses, W.W.; Andreaco, M.S.; Petterson, O.

2000-01-01

We present construction methods and performance results for a production scintillator array of 64 optically isolated, 3 mm x 3 mm x 30 mm sized LSO crystals. This scintillator array has been developed for a PET detector module consisting of the 8x8 LSO array coupled on one end to a single photomultiplier tube (PMT) and on the opposite end to a 64 pixel array of silicon photodiodes (PD). The PMT provides an accurate timing pulse and initial energy discrimination, the PD identifies the crystal of interaction, the sum provides a total energy signal, and the PD/(PD+PMT) ratio determines the depth of interaction (DOI). Unlike the previous LSO array prototypes, we now glue Lumirror reflector material directly onto 4 sides of each crystal to obtain an easily manufactured, mechanically rugged array with our desired depth dependence. With 511 keV excitation, we obtain a total energy signal of 3600 electrons, pulse-height resolution of 25% fwhm, and 6-15 mm fwhm DOI resolution

Types, harms and improvement of saline soil in Songnen Plain

Science.gov (United States)

Wang, Zhengjun; Zhuang, Jingjing; Zhao, Anping; Li, Xinxin

2018-03-01

Saline soil is an extremely difficult and modified soil, widely distributed around the world. According to UN-UNESCO and FAO, the world’s saline soil area is about 9.54×108hm2, and there is a growing trend, every year in 1.0×106-1.5×106hm2 speed growth, the effective utilization of land resources to the world is the most serious threat. The total area of saline-alkali land in China is about 9.91×107hm2, including the Songnen Plain, which is called one of the three major saline soil concentrations in the world. The Songnen plain is an important grain producing area in China, and the saline soil occupies most of the Songnen plain, so it is of great significance to study the saline soil and improvement in Songnen plain.

Seismic Investigation of the Glacier de la Plaine Morte, Switzerland

Science.gov (United States)

Laske, Gabi; Lindner, Fabian; Walter, Fabian; Krage, Manuel

2017-04-01

Glacier de la Plaine Morte is a plateau glacier along the border between Valais and Berne cantons. It covers a narrow elevation range and is extremely vulnerable to climate change. During snow melt, it feeds three marginal lakes that have experienced sudden subglacial drainage in recent years, thereby causing flooding in the Simme Valley below. Of greatest concern is Lac des Faverges at the southeastern end of the glacier that has drained near the end of July in recent years, with flood levels reaching capacity of flood control systems downstream. The lake levels are carefully monitored but precise prediction has not yet been achieved. In the search for precursory ice fracturing to the lake drainage to improve forecast, four seismic arrays comprised of five short-period borehole seismometers provided by Eidgenössische Technische Hochschule (ETH), Zürich as well as fifteen 3-component geophones from the Geophysical Instrument Pool Potsdam (GIPP) collected continuous seismic data for about seven weeks during the summer of 2016. We present initial results on discharge dynamics as well as changing noise levels and seismicity before, during and after the drainage of Lac des Faverges. Compared to previous recent years, the 2016 drainage of Lac des Faverges occurred unusually late on August 28. With an aperture between 100 and 200 m, the small arrays recorded many hundred ice quakes per day. A majority of the events exhibits clearly dispersed, high-frequency Rayleigh waves at about 10 Hz and higher. A wide distribution of events allows us to study azimuthal anisotropy and its relationship with the orientation of glacial crevasses.

Evaluating the Use of Plain Language in a Cancer Clinical Trial Website/App.

Science.gov (United States)

Schultz, Paula L; Carlisle, Regina; Cheatham, Chesley; O'Grady, Melissa

2017-12-01

Medically complex titles and descriptions found on clinical trial websites and online applications present a barrier to comprehension for users from the general public. In this study, we examine the effectiveness of plain language trial descriptions for user comprehension of basic trial details. Two hundred seventeen volunteers recruited from patient waiting areas completed 441 user tests of ten plain language trial descriptions. The majority of volunteers adequately comprehended the cancer type and basic inclusion/exclusion criteria from plain language trial descriptions. Difficulty comprehending the treatment being studied was seen in seven of ten descriptions tested. Revision and retesting of the seven trial descriptions showed continued user challenges in comprehending the treatment being studied. Plain language clinical trial descriptions integrated into a website/app allowed users to understand basic inclusion/exclusion criteria. Despite plain language used, discerning the treatment being studied may be difficult for some users. Integration of plain language descriptions into clinical trial online applications can help users understand trial basics. Further research regarding effective use of plain language to communicate the treatment being studied is needed.

Artificial urethral sphincters: Value of plain film radiography in evaluation of prosthesis malfunction

International Nuclear Information System (INIS)

Rose, S.C.; Hansen, M.E.; Webster, G.; Dunnick, N.R.

1987-01-01

Case records were reviewed to determine the diagnostic efficacy of plain radiographs in the evaluation of inflatable artificial urethral sphincters. Of 84 patients with prostheses, 21 (25%) developed complications. Fluid leaks were found in 16 patients who presented with recurrent incontinence; plain radiographs demonstrated an interval decrease in balloon reservoir diameter. Kinked tubing, which was evident on plain films, caused acute urinary retention in three patients. However, plain radiographs failed to detect evidence of prosthesis erosion into the urethra in either of two patients with this complication. Although urethroscopy is needed to detect urethral erosion, plain radiographs are inexpensive and reliable in the initial evaluation of artifical sphincter malfunction

Radon-prone areas in the Lombard plain

International Nuclear Information System (INIS)

Sesana, Lucia; Polla, Giancarla; Facchini, Ugo; De Capitani, Luisa

2005-01-01

This paper reports the results of indoor radon measurements carried out in the Lombard plain. The aim of this study, which is based on the geological context, was to identify radon high-risk areas. The underlying geology has been established by means of the available stratigraphies giving a schematic representation of the sites in which either occurrence of gravel or silt and clay predominate with depths ranging from 0 to 50 m. Radon measurements were performed in a sample of 411 one-family houses in seven villages located in the southern area of Bergamo and Brescia. The findings indicate that when the substrate is dominated by clay, radon concentration for dwellings on the ground floor are low, whereas a strong predominance of underlying gravel mixed up in sand gives in winter months high radon flux from underground

Radon-prone areas in the Lombard plain

Energy Technology Data Exchange (ETDEWEB)

Sesana, Lucia [Istituto di Fisica Generale Applicata, Universita degli Studi di Milano, Via G. Celoria, 16 - 20133 Milan (Italy)]. E-mail: lucia.sesana@unimi.it; Polla, Giancarla [Istituto di Fisica Generale Applicata, Universita degli Studi di Milano, Via G. Celoria, 16 - 20133 Milan (Italy); Facchini, Ugo [Istituto di Fisica Generale Applicata, Universita degli Studi di Milano, Via G. Celoria, 16 - 20133 Milan (Italy); De Capitani, Luisa [Dipartimento di Scienze della Terra, Universita degli Studi di Milano, Via Botticelli, 23 - 20133 Milan (Italy)

2005-07-01

This paper reports the results of indoor radon measurements carried out in the Lombard plain. The aim of this study, which is based on the geological context, was to identify radon high-risk areas. The underlying geology has been established by means of the available stratigraphies giving a schematic representation of the sites in which either occurrence of gravel or silt and clay predominate with depths ranging from 0 to 50 m. Radon measurements were performed in a sample of 411 one-family houses in seven villages located in the southern area of Bergamo and Brescia. The findings indicate that when the substrate is dominated by clay, radon concentration for dwellings on the ground floor are low, whereas a strong predominance of underlying gravel mixed up in sand gives in winter months high radon flux from underground.

MEMS two-axis force plate array used to measure the ground reaction forces during the running motion of an ant

International Nuclear Information System (INIS)

Takahashi, Hidetoshi; Thanh-Vinh, Nguyen; Jung, Uijin G; Shimoyama, Isao; Matsumoto, Kiyoshi

2014-01-01

A terrestrial insect can perform agile running maneuvers. However, the balance of ground reaction forces (GRFs) between each leg in an insect have remained poorly characterized. In this report, we present a micro force plate array for the simultaneous measurement of the anterior and vertical components of GRFs of multiple legs during the running motion of an ant. The proposed force plate, which consists of a 2000 µm × 980 µm × 20 µm plate base as the contact surface of an ant's leg, and the supported beams with piezoresistors on the sidewall and surface are sufficiently compact to be adjacently arrayed along the anterior direction. Eight plates arrayed in parallel were fabricated on the same silicon-on-insulator substrate to narrow the gap between each plate to 20 µm. We compartmented the plate surface into 32 blocks and evaluated the sensitivities to two-axis forces in each block so that the exerted forces could be detected wherever a leg came into contact. The force resolutions in both directions were under 1 µN within ±20 µN. Using the fabricated force plate array, we achieved a simultaneous measurement of the GRFs of three legs on one side while an ant was running. (paper)

Nanopillar arrays on semiconductor membranes as electron emission amplifiers.

Science.gov (United States)

Qin, Hua; Kim, Hyun-Seok; Blick, Robert H

2008-03-05

A new transmission-type electron multiplier was fabricated from silicon-on-insulator (SOI) material by integrating an array of one-dimensional (1D) silicon nanopillars onto a two-dimensional (2D) silicon membrane. Primary electrons are injected into the nanopillar-membrane (NPM) system from the flat surface of the membrane, while electron emission from the nanopillars is probed by an anode. The secondary electron yield (SEY) from the nanopillars in the current device is found to be about 1.8 times that of the plain silicon membrane. This gain in electron number is slightly enhanced by the electric field applied from the anode. Further optimization of the dimensions of the NPM and an application of field emission promise an even higher gain for detector applications and allow for probing of electronic/mechanical excitations in an NPM system stimulated by incident particles or radiation.

Large arrays of dual-polarized multichroic TES detectors for CMB measurements with the SPT-3G receiver

Science.gov (United States)

Posada, Chrystian M.; Ade, Peter A. R.; Anderson, Adam J.; Avva, Jessica; Ahmed, Zeeshan; Arnold, Kam S.; Austermann, Jason; Bender, Amy N.; Benson, Bradford A.; Bleem, Lindsey; Byrum, Karen; Carlstrom, John E.; Carter, Faustin W.; Chang, Clarence; Cho, Hsiao-Mei; Cukierman, Ari; Czaplewski, David A.; Ding, Junjia; Divan, Ralu N. S.; de Haan, Tijmen; Dobbs, Matt; Dutcher, Daniel; Everett, Wenderline; Gannon, Renae N.; Guyser, Robert J.; Halverson, Nils W.; Harrington, Nicholas L.; Hattori, Kaori; Henning, Jason W.; Hilton, Gene C.; Holzapfel, William L.; Huang, Nicholas; Irwin, Kent D.; Jeong, Oliver; Khaire, Trupti; Korman, Milo; Kubik, Donna L.; Kuo, Chao-Lin; Lee, Adrian T.; Leitch, Erik M.; Lendinez Escudero, Sergi; Meyer, Stephan S.; Miller, Christina S.; Montgomery, Joshua; Nadolski, Andrew; Natoli, Tyler J.; Nguyen, Hogan; Novosad, Valentyn; Padin, Stephen; Pan, Zhaodi; Pearson, John E.; Rahlin, Alexandra; Reichardt, Christian L.; Ruhl, John E.; Saliwanchik, Benjamin; Shirley, Ian; Sayre, James T.; Shariff, Jamil A.; Shirokoff, Erik D.; Stan, Liliana; Stark, Antony A.; Sobrin, Joshua; Story, Kyle; Suzuki, Aritoki; Tang, Qing Yang; Thakur, Ritoban B.; Thompson, Keith L.; Tucker, Carole E.; Vanderlinde, Keith; Vieira, Joaquin D.; Wang, Gensheng; Whitehorn, Nathan; Yefremenko, Volodymyr; Yoon, Ki Won

2016-07-01

Detectors for cosmic microwave background (CMB) experiments are now essentially background limited, so a straightforward alternative to improve sensitivity is to increase the number of detectors. Large arrays of multichroic pixels constitute an economical approach to increasing the number of detectors within a given focal plane area. Here, we present the fabrication of large arrays of dual-polarized multichroic transition-edge-sensor (TES) bolometers for the South Pole Telescope third-generation CMB receiver (SPT-3G). The complete SPT-3G receiver will have 2690 pixels, each with six detectors, allowing for individual measurement of three spectral bands (centered at 95 GHz, 150 GHz and 220 GHz) in two orthogonal polarizations. In total, the SPT-3G focal plane will have 16140 detectors. Each pixel is comprised of a broad-band sinuous antenna coupled to a niobium microstrip transmission line. In-line filters are used to define the different band-passes before the millimeter-wavelength signal is fed to the respective Ti/Au TES sensors. Detectors are read out using a 64x frequency domain multiplexing (fMux) scheme. The microfabrication of the SPT-3G detector arrays involves a total of 18 processes, including 13 lithography steps. Together with the fabrication process, the effect of processing on the Ti/Au TES's Tc is discussed. In addition, detectors fabricated with Ti/Au TES films with Tc between 400 mK 560 mK are presented and their thermal characteristics are evaluated. Optical characterization of the arrays is presented as well, indicating that the response of the detectors is in good agreement with the design values for all three spectral bands (95 GHz, 150 GHz, and 220 GHz). The measured optical efficiency of the detectors is between 0.3 and 0.8. Results discussed here are extracted from a batch of research of development wafers used to develop the baseline process for the fabrication of the arrays of detectors to be deployed with the SPT-3G receiver. Results from

Far-infrared imaging arrays for fusion plasma density and magnetic field measurements

International Nuclear Information System (INIS)

Neikirk, D.P.; Rutledge, D.B.

1982-01-01

Far-infrared imaging detector arrays are required for the determination of density and local magnetic field in fusion plasmas. Analytic calculations point out the difficulties with simple printed slot and dipole antennas on ungrounded substrates for use in submillimeter wave imaging arrays because of trapped surface waves. This is followed by a discussion of the use of substrate-lens coupling to eliminate the associated trapped surface modes responsible for their poor performance. This integrates well with a modified bow-tie antenna and permits diffraction-limited imaging. Arrays using bismuth microbolometers have been successfully fabricated and tested at 1222μm and 119μm. A 100 channel pilot experiment designed for the UCLA Microtor tokamak is described. (author)

Bearing estimation with acoustic vector-sensor arrays

International Nuclear Information System (INIS)

Hawkes, M.; Nehorai, A.

1996-01-01

We consider direction-of-arrival (DOA) estimation using arrays of acoustic vector sensors in free space, and derive expressions for the Cramacute er-Rao bound on the DOA parameters when there is a single source. The vector-sensor array is seen to have improved performance over the traditional scalar-sensor (pressure-sensor) array for two distinct reasons: its elements have an inherent directional sensitivity and the array makes a greater number of measurements. The improvement is greatest for small array apertures and low signal-to-noise ratios. Examination of the conventional beamforming and Capon DOA estimators shows that vector-sensor arrays can completely resolve the bearing, even with a linear array, and can remove the ambiguities associated with spatial undersampling. We also propose and analyze a diversely-oriented array of velocity sensors that possesses some of the advantages of the vector-sensor array without the increase in hardware and computation. In addition, in certain scenarios it can avoid problems with spatially correlated noise that the vector-sensor array may suffer. copyright 1996 American Institute of Physics

137Cs contamination of the Techa river flood plain near the village of Muslumovo

International Nuclear Information System (INIS)

Chesnokov, A.V.; Govorun, A.P.; Linnik, V.G.; Shcherbak, S.B.

2000-01-01

The results of a radiometric survey of the Techa river flood plain near the village of Muslumovo in the Chelyabinsk region of Russia are presented. The observed territory extended 16.6 km along the riverbed, with a total area of 2.5 km 2 . The collimated scintillation detector technique was applied to in situ field measurements of 137 Cs deposition on the soil. Maps of 137 Cs deposition and soil penetration depth were developed on the basis of approximately 5000 measurements. The total 137 Cs deposition within the surveyed territory has been estimated at 6.6 TBq. The means of the total 137 Cs soil depositions at half-kilometer sites on the flood plain and its distribution along the river have also been calculated. A maximum 137 Cs contamination above 7.5 MBq/m 2 is associated with a bank height up to 1 m above the usual water level. The data identify zones of intensive radionuclide sedimentation and transit zones

An orientation measurement method based on Hall-effect sensors for permanent magnet spherical actuators with 3D magnet array.

Science.gov (United States)

Yan, Liang; Zhu, Bo; Jiao, Zongxia; Chen, Chin-Yin; Chen, I-Ming

2014-10-24

An orientation measurement method based on Hall-effect sensors is proposed for permanent magnet (PM) spherical actuators with three-dimensional (3D) magnet array. As there is no contact between the measurement system and the rotor, this method could effectively avoid friction torque and additional inertial moment existing in conventional approaches. Curved surface fitting method based on exponential approximation is proposed to formulate the magnetic field distribution in 3D space. The comparison with conventional modeling method shows that it helps to improve the model accuracy. The Hall-effect sensors are distributed around the rotor with PM poles to detect the flux density at different points, and thus the rotor orientation can be computed from the measured results and analytical models. Experiments have been conducted on the developed research prototype of the spherical actuator to validate the accuracy of the analytical equations relating the rotor orientation and the value of magnetic flux density. The experimental results show that the proposed method can measure the rotor orientation precisely, and the measurement accuracy could be improved by the novel 3D magnet array. The study result could be used for real-time motion control of PM spherical actuators.

The Engineering Development Array: A Low Frequency Radio Telescope Utilising SKA Precursor Technology

Science.gov (United States)

Wayth, Randall; Sokolowski, Marcin; Booler, Tom; Crosse, Brian; Emrich, David; Grootjans, Robert; Hall, Peter J.; Horsley, Luke; Juswardy, Budi; Kenney, David; Steele, Kim; Sutinjo, Adrian; Tingay, Steven J.; Ung, Daniel; Walker, Mia; Williams, Andrew; Beardsley, A.; Franzen, T. M. O.; Johnston-Hollitt, M.; Kaplan, D. L.; Morales, M. F.; Pallot, D.; Trott, C. M.; Wu, C.

2017-08-01

We describe the design and performance of the Engineering Development Array, which is a low-frequency radio telescope comprising 256 dual-polarisation dipole antennas working as a phased array. The Engineering Development Array was conceived of, developed, and deployed in just 18 months via re-use of Square Kilometre Array precursor technology and expertise, specifically from the Murchison Widefield Array radio telescope. Using drift scans and a model for the sky brightness temperature at low frequencies, we have derived the Engineering Development Array's receiver temperature as a function of frequency. The Engineering Development Array is shown to be sky-noise limited over most of the frequency range measured between 60 and 240 MHz. By using the Engineering Development Array in interferometric mode with the Murchison Widefield Array, we used calibrated visibilities to measure the absolute sensitivity of the array. The measured array sensitivity matches very well with a model based on the array layout and measured receiver temperature. The results demonstrate the practicality and feasibility of using Murchison Widefield Array-style precursor technology for Square Kilometre Array-scale stations. The modular architecture of the Engineering Development Array allows upgrades to the array to be rolled out in a staged approach. Future improvements to the Engineering Development Array include replacing the second stage beamformer with a fully digital system, and to transition to using RF-over-fibre for the signal output from first stage beamformers.

Summary of findings from the Great Plains Tree and Forest Invasives Initiative

Science.gov (United States)

Dacia M. Meneguzzo; Andrew J. Lister; Cody. Sullivan

2018-01-01

The Great Plains Tree and Forest Invasives Initiative (GPI) was a cooperative effort of the U.S. Forest Service and state forestry agencies in Kansas, Nebraska, North Dakota, and South Dakota, with a primary goal of evaluating the tree resources throughout the four-state region as a preparedness measure for the arrival of invasive pests, such as the emerald ash borer...

The Maryland Coastal Plain Aquifer Information System: A GIS-based tool for assessing groundwater resources

Science.gov (United States)

Andreasen, David C.; Nardi, Mark R.; Staley, Andrew W.; Achmad, Grufron; Grace, John W.

2016-01-01

information system can serve as a pre- and postprocessing environment for groundwater-flow models for use in water-supply planning, development, and management. The system also can be expanded to include features that evaluate constraints to groundwater development, such as insufficient available drawdown, degraded groundwater quality, insufficient aquifer yields, and well-field interference. Ultimately, the aquifer information system is intended to function as an interactive Web-based utility that provides a broad array of information related to groundwater resources in Maryland’s coastal plain to a wide-ranging audience, including well drillers, consultants, academia, and the general public.

Experimental measurement of fluid force coefficients for helical tube arrays in air cross flow

International Nuclear Information System (INIS)

Shen Shifang; Liu Reilan

1993-01-01

A helical coil steam generator is extensively used in the High Temperature Gas Cooled Reactor (HTGCR) and Sodium Cooled Reactor (SCR) nuclear power stations because of its compact structure, good heat-exchange, and small volume. The experimental model is established by the structure parameter of 200MW HTGCR. The fluid elastic instability of helical tube arrays in air cross flow is studied in this experiment, and the fluid force coefficients of helical tube arrays having the same notational direction of two adjacent layers in air cross flow are obtained. As compared to the fluid force coefficients of cylinder tube arrays, the fluid force coefficients of helical tube arrays are smaller in the low velocity area, and greater in the high velocity area. The experimental results help the study of the dynamic characteristics of helical tube arrays in air cross flow

Optical properties of titanium dioxide nanotube arrays

Energy Technology Data Exchange (ETDEWEB)

Abdelmoula, Mohamed [Department of Physics, Northeastern University, Boston, Massachusetts 02115 (United States); Department of Materials Science, Carnegie Mellon University, Pittsburgh, PA 15213 (United States); Sokoloff, Jeffrey; Lu, Wen-Tao; Menon, Latika [Department of Physics, Northeastern University, Boston, Massachusetts 02115 (United States); Close, Thomas; Richter, Christiaan, E-mail: christiaan.richter@rit.edu [Department of Chemical Engineering, Rochester Institute of Technology, Rochester, New York, 14623 (United States)

2014-01-07

We present experimental measurements and a theoretical analysis of the near UV to NIR optical properties of free standing titania nanotube arrays. An improved understanding of the optical physics of this type of nanostructure is important to several next generation solar energy conversion technologies. We measured the transmission, reflection, and absorption of the electromagnetic spectrum from 300 nm to 1000 nm (UV to NIR) of titania nanotube arrays. We measured the total, specular, and diffuse reflection and transmission using both single point detection and an integrating sphere spectrometer. We find that the transmission, but not the reflection, of light (UV to NIR) through the nanotube array is well-explained by classic geometric optics using an effective medium model taking into account the conical geometry of the nanotubes. For wavelengths shorter than ∼500 nm, we find the surprising result that the reflection coefficient for light incident on the open side of the nanotube array is greater than the reflection coefficient for light incident on the closed “floor” of the nanotube array. We consider theoretical models based on the eikonal approximation, photonic crystal band theory, and a statistical treatment of scattering to explain the observed data. We attribute the fact that light with wavelengths shorter than 500 nm is more highly reflected from the open than the closed tube side as being due to disorder scattering inside the nanotube array.

Acute paediatric ankle trauma: MRI versus plain radiography

Energy Technology Data Exchange (ETDEWEB)

Lohman, M. [Helsinki Univ. Central Hospital (Finland). Dept. of Radiology; Radiological Dept., Helsinki University Central Hospital (Finland); Kivisaari, A.; Kivisaari, L. [Helsinki Univ. Central Hospital (Finland). Dept. of Radiology; Kallio, P.; Puntila, J. [Dept. of Paediatric Surgery, Hospital for Children and Adolescents, Helsinki Univ. Central Hospital, Helsinki (Finland); Vehmas, T. [Finnish Institute of Occupational Health, Helsinki (Finland)

2001-09-01

Objective: To evaluate the diagnosis of acute physeal ankle fractures on plain radiographs using MRI as the gold standard. Methods: Sixty consecutive children, 29 with a clinical diagnosis of lateral ligament injury and 31 with physeal ankle fractures, were examined using both radiographs and MRI in the acute period. The imaging data were reviewed by three ''masked'' radiologists. The fracture diagnosis and Slater-Harris classification of radiographs were compared with findings on MRI. Results: Plain radiography produced five of 28 (18%) false negative and 12 of 92 (13%) false positive fracture diagnoses compared with MRI. Six of the 12 false positive fractures were due to a misclassification of lateral ligament disruption as SH1 fractures. Altogether a difference was found in 21% of cases in either the diagnosis or the classification of the fractures according to Salter- Harris. All bone bruises in the distal tibia and fibula and 64% of bone bruises in the talus were seen in association with lateral ligament injuries. Talar bone bruises in association with fractures occurred on the same side as the malleolar fracture; talar bone bruises in association with lateral ligament disruption were seen in different locations. The errors identified on radiographs by MRI did not affect the management of the injury. Conclusions: The incidence of false negative ankle fractures in plain radiographs was small and no complex ankle fractures were missed on radiographs. The total extent of complex fractures was, however, not always obvious on radiographs. In an unselected series of relatively mild ankle injuries, we were unable to show a single case where the treatment or prognosis based on plain radiography should have been significantly altered after having done a routine MRI examination. Plain radiography is still the diagnostic cornerstone of paediatric ankle injuries. (orig.)

Acute paediatric ankle trauma: MRI versus plain radiography

International Nuclear Information System (INIS)

Lohman, M.; Kivisaari, A.; Kivisaari, L.; Vehmas, T.

2001-01-01

Objective: To evaluate the diagnosis of acute physeal ankle fractures on plain radiographs using MRI as the gold standard. Methods: Sixty consecutive children, 29 with a clinical diagnosis of lateral ligament injury and 31 with physeal ankle fractures, were examined using both radiographs and MRI in the acute period. The imaging data were reviewed by three ''masked'' radiologists. The fracture diagnosis and Slater-Harris classification of radiographs were compared with findings on MRI. Results: Plain radiography produced five of 28 (18%) false negative and 12 of 92 (13%) false positive fracture diagnoses compared with MRI. Six of the 12 false positive fractures were due to a misclassification of lateral ligament disruption as SH1 fractures. Altogether a difference was found in 21% of cases in either the diagnosis or the classification of the fractures according to Salter- Harris. All bone bruises in the distal tibia and fibula and 64% of bone bruises in the talus were seen in association with lateral ligament injuries. Talar bone bruises in association with fractures occurred on the same side as the malleolar fracture; talar bone bruises in association with lateral ligament disruption were seen in different locations. The errors identified on radiographs by MRI did not affect the management of the injury. Conclusions: The incidence of false negative ankle fractures in plain radiographs was small and no complex ankle fractures were missed on radiographs. The total extent of complex fractures was, however, not always obvious on radiographs. In an unselected series of relatively mild ankle injuries, we were unable to show a single case where the treatment or prognosis based on plain radiography should have been significantly altered after having done a routine MRI examination. Plain radiography is still the diagnostic cornerstone of paediatric ankle injuries. (orig.)

Large scale biomimetic membrane arrays

DEFF Research Database (Denmark)

Hansen, Jesper Søndergaard; Perry, Mark; Vogel, Jörg

2009-01-01

To establish planar biomimetic membranes across large scale partition aperture arrays, we created a disposable single-use horizontal chamber design that supports combined optical-electrical measurements. Functional lipid bilayers could easily and efficiently be established across CO2 laser micro......-structured 8 x 8 aperture partition arrays with average aperture diameters of 301 +/- 5 mu m. We addressed the electro-physical properties of the lipid bilayers established across the micro-structured scaffold arrays by controllable reconstitution of biotechnological and physiological relevant membrane...... peptides and proteins. Next, we tested the scalability of the biomimetic membrane design by establishing lipid bilayers in rectangular 24 x 24 and hexagonal 24 x 27 aperture arrays, respectively. The results presented show that the design is suitable for further developments of sensitive biosensor assays...

Imaging suspected cervical spine injury: Plain radiography or computed tomography? Systematic review

Energy Technology Data Exchange (ETDEWEB)

Cain, Gavin [Diagnostic Radiographer, Colchester Hospital University NHS Foundation Trust, Colchester General Hospital, Turner Road, Colchester, CO4 5JL Essex (United Kingdom)], E-mail: gavincain8@hotmail.com; Shepherdson, Jane; Elliott, Vicki; Svensson, Jon [Faculty of Health and Social Care, Anglia Ruskin University, East Road, Cambridge, CB1 9PT Cambridgeshire (United Kingdom); Brennan, Patrick [UCD School of Medicine and Medical Sciences, Health Science Building, Belfield, Dublin 4 (Ireland)

2010-02-15

Aim: (1) to establish which modality offers the greatest accuracy in the detection of cervical spine injury (CSI) Following trauma: plain radiography or computed tomography (CT), and (2) make an evidence-based recommendation for the initial imaging modality of choice. Method: A systematic literature review was performed to identify primary research studies which compare the diagnostic accuracy of plain radiography and CT with the results of a reference standard in the detection of CSI. A search of MEDLINE, EMBASE, CINAHL, Science Direct and Pubmed Central databases was conducted. Results: Ten studies were identified. Critical appraisal identified limitations among all studies. There was heterogeneity in the sensitivity estimates for plain radiography, whereas estimates for CT were consistently high. Examination of the reported sensitivities shows that CT outperforms plain radiography in the detection of CSI. Conclusion: CT is superior to plain radiography in the detection of CSI. However, the optimal imaging strategy depends on the patients' relative risk of injury. If at high-risk cervical CT is indicated. If at low-risk the increased cost and radiation exposure mean that screening CT may not be warranted, good-quality plain radiographs are sufficient.

Coastal geomorphology of the Martian northern plains

Science.gov (United States)

Parker, Timothy J.; Gorsline, Donn S.; Saunders, Stephen R.; Pieri, David C.; Schneeberger, Dale M.

1993-01-01

The paper considers the question of the formation of the outflow channels and valley networks discovered on the Martian northern plains during the Mariner 9 mission. Parker and Saunders (1987) and Parker et al. (1987, 1989) data are used to describe key features common both in the lower reaches of the outflow channels and within and along the margins of the entire northern plains. It is suggested, that of the geological processes capable of producing similar morphologies on earth, lacustrine or marine deposition and subsequent periglacial modification offer the simplest and most consistent explanation for the suit of features found on Mars.

Plain language: a strategic response to the health literacy challenge.

Science.gov (United States)

Stableford, Sue; Mettger, Wendy

2007-01-01

Low health literacy is a major challenge confronting American and international health organizations. Research in the past decade has documented the prevalence of limited literacy and limited health literacy skills among adults worldwide. This creates a major policy challenge: how to create text-based health information - a common method of health communication - that is accessible to the public. Plain language is a logical, flexible response. While touted by American, Canadian, and European health policy makers, adoption and promotion of plain language standards and skills in health-focused organizations have lagged. Most text-based health information continues to be too hard for most adults to read. Barriers to more rapid diffusion of plain language are reflected in a set of myths perpetuated by critics. These myths are identified and refuted. While plain language is only one of many broad-based solutions needed to address low health literacy, the benefits to everyone demand increased use by health organizations.

Plain abdominal radiographs in acute medical emergencies: an abused investigation?

Science.gov (United States)

Feyler, S; Williamson, V; King, D

2002-02-01

Plain abdominal radiographs are commonly requested for acute medical emergencies on patients with non-specific abdominal symptoms and signs. In this study 131 plain abdominal radiographs performed on the day of admission were prospectively analysed. In only 16 cases (12%) the reasons for requests conformed to the recommended guidelines by the Royal College of Radiologists. The reason for the request was stated in the case notes in only three cases. In 62 cases (47%), there was no comment made on the film by the requesting clinician. There was a discrepancy in the interpretation of the radiograph between the clinician and the radiologist in 31 cases (24%). The clinical management was influenced by plain abdominal radiographs in only nine cases (7%). The majority of plain abdominal radiographs requested on acute medical emergencies is inappropriate. There is a need to ensure guidelines are followed to prevent unnecessary exposure of patients to radiation as well as preventing expenditure on irrelevant investigations.

Geothermal Alteration of Basaltic Core from the Snake River Plain, Idaho

OpenAIRE

Sant, Christopher Joseph

2012-01-01

The Snake River Plain is located in the southern part of the state of Idaho. The eastern plain, on which this study focuses, is a trail of volcanics from the Yellowstone hotspot. Three exploratory geothermal wells were drilled on the Snake River Plain. This project analyzes basaltic core from the first well at Kimama, north of Burley, Idaho. The objectives of this project are to establish zones of geothermal alteration and analyze the potential for geothermal power production using sub-aquife...

Changes in plain bearing technology

CERN Document Server

Koring, Rolf

2012-01-01

A unique fusion of theoretical and practical knowledge, Changes in Plain Bearing Technology, by Rolf Koring, covers a meaningful range of expertise in this field.Drawing from years of experience in design development, materials selection, and their correlation to real-life part failure, this title, co-published by SAE International and expert Verlag (Germany), concentrates on hydrodynamic bearings lined with white metals, also known as Babbits.Written under the assumption that even the most mature body of knowledge can be revisited and improved, Changes in Plain Bearing Technology is a courageous and focused approach to questioning accepted test results and looking at alternative material compounds, and their application suitability.The process, which leads to innovative answers on how the technology is transforming itself to respond to new market requirements, shows how interdisciplinary thinking can recognize new potential in long-established industrial modus operandi.Tackling the highly complex issue of co...

Phased-array design for MST and ST radars

Science.gov (United States)

Ecklund, W. L.

1986-01-01

All of the existing radar systems fully dedicated to clear-air radar studies use some type of phased-array antennas. The effects of beam-steering techniques including feed networks and phase shifters; sidelobe control; ground-clutter suppression; low altitude coverage; arrays with integrated radiating elements and feed networks; analysis of coaxial-collinear antennas; use of arrays with multiple beams; and array testing and measure on structural design of the antenna are discussed.

Curved Microneedle Array-Based sEMG Electrode for Robust Long-Term Measurements and High Selectivity

Directory of Open Access Journals (Sweden)

Minjae Kim

2015-07-01

Full Text Available Surface electromyography is widely used in many fields to infer human intention. However, conventional electrodes are not appropriate for long-term measurements and are easily influenced by the environment, so the range of applications of sEMG is limited. In this paper, we propose a flexible band-integrated, curved microneedle array electrode for robust long-term measurements, high selectivity, and easy applicability. Signal quality, in terms of long-term usability and sensitivity to perspiration, was investigated. Its motion-discriminating performance was also evaluated. The results show that the proposed electrode is robust to perspiration and can maintain a high-quality measuring ability for over 8 h. The proposed electrode also has high selectivity for motion compared with a commercial wet electrode and dry electrode.

Young people's perceptions of cigarette packaging and plain packaging: an online survey.

Science.gov (United States)

Moodie, Crawford; Ford, Allison; Mackintosh, Anne Marie; Hastings, Gerard

2012-01-01

In the United Kingdom, with most marketing channels prohibited, packaging is one of the few remaining ways that tobacco companies can promote their products. An online survey with young people aged 10-17 years (N = 658) was used to explore why youth choose cigarettes, perceptions of pack color, and perceptions of plain (nonbranded) cigarette packaging. Young people were also shown an image of 3 plain packs, which differed by shape and method of opening, and asked which they liked most and thought others their age would smoke. Price and what significant others smoke were key factors for choosing cigarettes, with packaging also an important influence. More than a third of the sample associated lighter pack color with weak tasting and less harmful cigarettes. Plain packs were rated negatively as were perceptions of plain pack users. One in 3 showed a preference for either a narrow "perfume type" plain pack or a plain "slide" pack that opened from the side, and 1 in 3 also thought that young people would smoke these packs. Packaging appears to both attract young people and mislead them about product strength and relative harm. Innovative pack construction (novel pack shape and method of opening) and the use of color are instrumental in these effects. The findings therefore suggest that any move to plain packaging should not only consider the benefits of removing branding (including color) but also of standardizing pack construction in terms of shape and method of opening.

No (more) logo: plain packaging and communicative agency

OpenAIRE

Alain Pottage

2013-01-01

The tobacco industry’s archives suggest that the global campaign for the plain packaging of tobacco products originated in 1986, when the Canadian Medical Association passed a resolution calling for cigarettes to be sold in packages bearing only a brand name and the health message ‘this product is injurious to your health’. In most jurisdictions, regulations requiring the apposition of health warnings to cigarette packs have been in force for decades. Proposals for plain packaging aim to go f...

Evaluation of the applicability of the SWAT model in an arid piedmont plain oasis.

Science.gov (United States)

Wu, Yong; Li, Changyou; Zhang, Chengfu; Shi, Xiaohong; Bourque, Charles P-A; Zhao, Shengnan

2016-01-01

Hetao Oasis is located in a typical piedmont alluvial plain bounded by the Langshan Mountain Range in the north, desert in the west, and the Yellow River in the south. Agricultural activities within the oasis significantly impact the hydrological cycle and water quality in downstream locations. The research uses the Soil and Water Assessment Tool (SWAT) for a piedmont plain by defining the watershed boundary as coinciding with the natural mountain ridge, the border between the oasis and the desert, and the Yellow River. The model simulates water discharge with coefficient of determination and a Nash-Sutcliffe model efficiency of 0.78 and 0.62 during model calibration, and 0.75 and 0.69 during model validation, suggesting that delineation of the watershed as carried out in this research is suitable for piedmont plain topography. From the results, the mountains contribute 28.4% to the water discharge at the outlet of the watershed, and water-use efficiency of irrigated water is about 40%, which is consistent with field-based measurements. Methodologies used in delineating watershed boundaries and parameterizing SWAT provide a solid foundation for water balance studies in other regions of the world with similar topography.

ESPRIT And Uniform Linear Arrays

Science.gov (United States)

Roy, R. H.; Goldburg, M.; Ottersten, B. E.; Swindlehurst, A. L.; Viberg, M.; Kailath, T.

1989-11-01

Abstract ¬â€?ESPRIT is a recently developed and patented technique for high-resolution estimation of signal parameters. It exploits an invariance structure designed into the sensor array to achieve a reduction in computational requirements of many orders of magnitude over previous techniques such as MUSIC, Burg's MEM, and Capon's ML, and in addition achieves performance improvement as measured by parameter estimate error variance. It is also manifestly more robust with respect to sensor errors (e.g. gain, phase, and location errors) than other methods as well. Whereas ESPRIT only requires that the sensor array possess a single invariance best visualized by considering two identical but other-wise arbitrary arrays of sensors displaced (but not rotated) with respect to each other, many arrays currently in use in various applications are uniform linear arrays of identical sensor elements. Phased array radars are commonplace in high-resolution direction finding systems, and uniform tapped delay lines (i.e., constant rate A/D converters) are the rule rather than the exception in digital signal processing systems. Such arrays possess many invariances, and are amenable to other types of analysis, which is one of the main reasons such structures are so prevalent. Recent developments in high-resolution algorithms of the signal/noise subspace genre including total least squares (TLS) ESPRIT applied to uniform linear arrays are summarized. ESPRIT is also shown to be a generalization of the root-MUSIC algorithm (applicable only to the case of uniform linear arrays of omni-directional sensors and unimodular cisoids). Comparisons with various estimator bounds, including CramerRao bounds, are presented.

The Australian experience following plain packaging: the impact on tobacco branding.

Science.gov (United States)

Greenland, Steven J

2016-12-01

Brands are critical to tobacco marketing. Industry stakeholders predicted that plain packaging, by removing key tangible branding dimensions, would restrict new products and brand differentiation. However, manufacturers respond innovatively to limit regulatory impact. This study investigates brand strategy following plain packaging's introduction to Australia. Brand portfolios were determined using 2006-15 tobacco ingredient reports. These detail the brand and variant names sold and are provided annually as part of a voluntary agreement between the Australian Government and leading manufacturers. Post-plain packaging brand ranges were verified using retail price lists and a supermarket retail audit using a method used previously to verify a period of pre-plain packaging data. The verification process identified some data inaccuracies from one manufacturer which resulted in the issuing of corrected data. After plain packaging the leading manufacturers continued with extensive brand ranges differentiated by price. All launched new products. While total brand numbers fell from 29 to 24, the mean number of variants for the leading 12 brands grew from 8.9 to 9.7. Substantial variant name modifications occurred with 50 new or modified names in 2012-13. Among leading brands, the incidence of variant colour names increased from 49.5 to 79.3%. New brands and variants were not inhibited by the introduction of plain packaging in Australia. After plain packaging, leading brand variant numbers expanded by 9 to 116 and colour variant names increased by 73.6% and became the norm-lighter colours (blue, gold and silver) dominated, perpetuating notions of less harmful cigarettes. [Correction added on 09 September 2016, after first online publication: The figures in the last sentence of the Abstract are now corrected from 'expanded by 116' to 'expanded by 9 to 116'.]. © 2016 Society for the Study of Addiction.

Hierarchical sinuous-antenna phased array for millimeter wavelengths

Science.gov (United States)

Cukierman, Ari; Lee, Adrian T.; Raum, Christopher; Suzuki, Aritoki; Westbrook, Benjamin

2018-03-01

We present the design, fabrication, and measured performance of a hierarchical sinuous-antenna phased array coupled to superconducting transition-edge-sensor (TES) bolometers for millimeter wavelengths. The architecture allows for dual-polarization wideband sensitivity with a beam width that is approximately frequency-independent. We report on measurements of a prototype device, which uses three levels of triangular phased arrays to synthesize beams that are approximately constant in width across three frequency bands covering a 3:1 bandwidth. The array element is a lens-coupled sinuous antenna. The device consists of an array of hemispherical lenses coupled to a lithographed wafer, which integrates TESs, planar sinuous antennas, and microwave circuitry including band-defining filters. The approximately frequency-independent beam widths improve coupling to telescope optics and keep the sensitivity of an experiment close to optimal across a broad frequency range. The design can be straightforwardly modified for use with non-TES lithographed cryogenic detectors such as kinetic inductance detectors. Additionally, we report on the design and measurements of a broadband 180° hybrid that can simplify the design of future multichroic focal planes including but not limited to hierarchical phased arrays.

Ages of plains volcanism on Mars

Science.gov (United States)

Hauber, Ernst; Jagert, Felix; Broz, Petr

2010-05-01

Plain-style volcanism [1] is widespread in the Tharsis and Elysium volcanic provinces on Mars, [2,3]. Detailed images and topographic data reveal the morphology and topography of clusters of low shields and associated lava flows. The landforms of plains volcanism on Mars have all well-known terrestrial analogues in basaltic volcanic regions, such as Hawaii, Iceland, and in particular the Snake River Plains [4]. The very gentle flank slopes (J. (1981) Icarus, 45, 586-601. [3] Hodges C.A. and Moore H.J. (1994) Atlas of volcanic features on Mars: USGS Prof. Paper 1534, 194 p. [4] Hauber E. et al. (2009) J. Volcanol. Geotherm. Res. 185, 69-95. [5] Wilson L. et al. (2009) J. Volcanol. Geotherm. Res. 185, 28-46. [6] Vaucher, J. et al. (2009) Icarus 204, 418-442. [7] Baratoux D. et al. (2009) J. Volcanol. Geotherm. Res. 185, 47-68. [8] Bleacher J.E. et al. (2009) J. Volcanol. Geotherm. Res. 185, 96-102. [9] Ivanov B.A. (2001) Space Sci. Rev. 96, 87-104. [10] Hartmann W.H. and Neukum G. (2001) Space Sci. Rev. 96, 165-194 [11] Kneissl T. et al. (2010) LPS XVI, submitted. [12] Michael, G.G. and Neukum G. (2010) Earth Planet. Sci. Lett., in press. . [13] Malin M.C. et al. (2007) JGR 112, E05S04, doi: 10.1029/2006JE002808.

The innovation of nuclear science and technology supporting for the central plains economic zone construction

International Nuclear Information System (INIS)

Yang Xiaowei

2014-01-01

This paper discusses the nuclear agronomy support for the central plains economic zone construction, radiation chemical new material support for the central plains economic zone construction, nuclear medical support for the central plains economic zone construction, nuclear instrument and meter industry support for the central plains economic zone construction and the development trend of related disciplines. (author)

Measurements and Analysis of Chemical Composition of Particulate Matter during High Pollution Events at Guanzhong Plain, China

Science.gov (United States)

Junji, C.

2017-12-01

Particulate matter pollution is a serious environmental problem which influencing air quality, regional and global climates, and human health. PM2.5 samples were collected at Guanzhong Plain with six sampling sites atdifferent cities in the year scale from 2012 to 2014. All of the six sites exhibited highest organic carbon (OC)and elemental carbon (EC) values in winter and lowest values in summer. OC correlates well with EC indicating similar emission sources. The contributions of secondary species SO42-, NO3- and NH4+ in total ions were greatest, and the high concentrations in winter were mainly due to emissions from coal combustion and biomass burning.During autumn the haze days were severest in Xi'an city with similar tendency of PM2.5 variations, and it was proved that biomass burning may be the main emission source of the regional pollution. In winter pollution episodes, the pollution patterns in Guanzhong Plain were similar which was resulted from strong secondary reactions and coal burning.Source apportionment using a positive matrix factorizationreceptor model indicates that on average secondary aerosol was the main source of PM2.5 (39.3%), followed by coal burning (17.3%), motor vehicle/industrial emissions (15.7%), fugitive dust (14.9%), and biomass burning (12.8%). The online, in situ measurement airborne species, especially the chemical composition of non-refectory submicron aerosol, during a heavyhaze-fog event, was analyzed in detailed.The formation of secondary sulfate and organic aerosol were observed during the event. The sulfur oxidation ratio (SOR), defined as sulfate/(SO2+sulfate) were mostly over 0.10, with a maximum of 0.30, when relative humidity > 80%. The aging product of organic aerosol (OA) were also observed in the event. The wet scattering coefficient was influenced by secondary sulfate, in the form of (NH4)2SO4, with contribution of 48.9% of wet particulate phase scattering. Thus decreased the visibility dramatically with a minimum of

Evaluation of linear array MOSFET detectors for in vivo dosimetry to measure rectal dose in HDR brachytherapy.

Science.gov (United States)

Haughey, Aisling; Coalter, George; Mugabe, Koki

2011-09-01

The study aimed to assess the suitability of linear array metal oxide semiconductor field effect transistor detectors (MOSFETs) as in vivo dosimeters to measure rectal dose in high dose rate brachytherapy treatments. The MOSFET arrays were calibrated with an Ir192 source and phantom measurements were performed to check agreement with the treatment planning system. The angular dependence, linearity and constancy of the detectors were evaluated. For in vivo measurements two sites were investigated, transperineal needle implants for prostate cancer and Fletcher suites for cervical cancer. The MOSFETs were inserted into the patients' rectum in theatre inside a modified flatus tube. The patients were then CT scanned for treatment planning. Measured rectal doses during treatment were compared with point dose measurements predicted by the TPS. The MOSFETs were found to require individual calibration factors. The calibration was found to drift by approximately 1% ±0.8 per 500 mV accumulated and varies with distance from source due to energy dependence. In vivo results for prostate patients found only 33% of measured doses agreed with the TPS within ±10%. For cervix cases 42% of measured doses agreed with the TPS within ±10%, however of those not agreeing variations of up to 70% were observed. One of the most limiting factors in this study was found to be the inability to prevent the MOSFET moving internally between the time of CT and treatment. Due to the many uncertainties associated with MOSFETs including calibration drift, angular dependence and the inability to know their exact position at the time of treatment, we consider them to be unsuitable for in vivo dosimetry in rectum for HDR brachytherapy.

Evaluation of linear array MOSFET detectors for in vivo dosimetry to measure rectal dose in DHR brachytherapy

International Nuclear Information System (INIS)

Haughey, A.; Coalter, G.; Mugabe, K.

2011-01-01

Full text: The study aimed to assess the suitability of linear array metal oxide semiconductor field effect transistor detectors (MOSFETs) as in vivo dosimeters to measure rectal dose in high dose rate brachytherapy treatments. The MOSFET arrays were calibrated with an Ir192 source and phantom measurements were performed to check agreement with the treatment planning system. The angular dependence, linearity and constancy of the detectors were evaluated. For in vivo measurements two sites were investigated, transperineal needle implants for prostate cancer and Fletcher suites for cervical cancer. The MOSFETs were inserted into the patients' rectum in theatre inside a modified flatus tube. The patients were then CT scanned for treatment planning. Measured rectal doses during treatment were compared with point dose measurements predicted by the TPS. The MOSFETs were found to require individual calibration factors. The calibration was found to drift by approximately 1% ±0.8 per 500 mV accumulated and varies with distance from source due to energy dependence. In vivo results for prostate patients found only 33% of measured doses agreed with the TPS within ±1O%. For cervix cases 42% of measured doses agreed with the TPS within ± 10%, however of those not agreeing variations of up to 70% were observed. One of the most limiting factors in this study was found to be the inability to prevent the MOSFET moving internally between the time of CT and treatment. Due to the many uncertainties associated with MOSFETs including calibration drift, angular dependence and the inability to know their exact position at the time of treatment, we consider them to be unsuitable for in vivo dosimetry in rectum for HDR brachytherapy. (author)

Accuracy of simple plain radiographic signs and measures to diagnose acute scapholunate ligament injuries of the wrist

Energy Technology Data Exchange (ETDEWEB)

Dornberger, Jenny E. [Unfallkrankenhaus Berlin, Department of Plastic Surgery and Burn Care, Berlin (Germany); Rademacher, Grit; Mutze, Sven [Unfallkrankenhaus Berlin, Institute of Radiology, Berlin (Germany); Eisenschenk, Andreas [Unfallkrankenhaus Berlin, Department of Hand-, Replantation- and Microsurgery, Berlin (Germany); University Medicine Greifswald, Department of Hand Surgery and Microsurgery, Greifswald (Germany); Stengel, Dirk [Unfallkrankenhaus Berlin, Centre for Clinical Research, Berlin (Germany); Charite Medical University Centre, Julius Wolff Institute, Centre for Musculoskeletal Surgery, Berlin (Germany)

2015-12-15

To determine the accuracy of common radiological indices for diagnosing ruptures of the scapholunate (SL) ligament, the most relevant soft tissue injury of the wrist. This was a prospective diagnostic accuracy study with independent verification of index test findings by a reference standard (wrist arthroscopy). Bilateral digital radiographs in posteroanterior (pa), lateral and Stecher's projection were evaluated by two independent expert readers. Diagnostic accuracy of radiological signs was expressed as sensitivity, specificity, positive (PPV) and negative (NPV) predictive values with 95 % confidence intervals (CI). The prevalence of significant acute SL tears (grade ≥ III according to Geissler's classification) was 27/72 (38 %, 95 % CI 26-50 %). The SL distance on Stecher's projection proved the most accurate index to rule the presence of an SL rupture in and out. SL distance on plain pa radiographs, Stecher's projection and the radiolunate angle contributed independently to the final diagnostic model. These three simple indices explained 97 % of the diagnostic variance. In the era of computed tomography and magnetic resonance imaging, plain radiographs remain a highly sensitive and specific primary tool to triage patients with a suspected SL tear to further diagnostic work-up and surgical care. (orig.)

Development of measurement technique for crack depth in weld zone of thick stainless steel pipe with ultrasonic phased array TOFD

International Nuclear Information System (INIS)

Ishida, Hitoshi

2006-01-01

Phased array TOFD (time of flight diffraction) method which makes possible to detect tip diffraction echoes and measure crack depth in an austenitic stainless steel weld zone with a thickness of more than 25 mm to which region it was difficult to apply ultrasonic test due to scattering of ultrasonic waves has been developed. The developed method uses a single array transducer to have a short distance between incident points of transmitter and receiver in order to propagate waves in shorter pass in the weld region. Transmitting and receiving ultrasonic beams from a single array probe can be set a crossing point and a focal point at desired depth. This method makes possible to scan with 16 kinds of combination of crossing points and focal pints of ultrasonic beam at a time. We have examined fundamental characteristics of depth measurement with electric discharge machining slits on base metal of a stainless steel with a thickness of 35 mm. As the results: (1) We could measure the slit depth with 0.2mm error from the slit depth with a estimating method of a lateral wave propagation time with back wall echo. (2) The largest error of the depth measurement from the slit depth with the ultrasonic beam crossing point set at the 4mm different point from the tip of the slit was 0.3 mm. (3) The largest error of the depth measurements due to the difference of focal point depth of ultrasonic beam was 0.2 mm. (4) The highest tip diffraction echo could be observed with the ultrasonic beam cross point set at the tip of the slit. The difference of 4 mm between the cross point and the tip of the slit caused attenuation of tip diffraction echo height in -6.8 dB. Furthermore we have measured a depth of electric discharge machining slits, fatigue cracks and stress corrosion cracking (SCC) on stainless steel welded pipe specimens with a thickness of 35 mm. As the results: (1) We could detect the tip diffraction echoes which have a signal noise ratio with more than 2.4 from the fatigue

Hydrology and water budget for a forested atlantic coastal plain watershed, South Carolina

Science.gov (United States)

Scott V. Harder; Devendra M Amatya; Callahan Timothy J.; Carl C. Trettin; Hakkila Jon

2007-01-01

Increases in timber demand and urban development in the Atlantic Coastal Plain over the past decade have motivated studies on the hydrology, water quality, and sustainable management of coastal plain watersheds. However, studies on baseline water budgets are limited for the low-lying, forested watersheds of the Atlantic Coastal Plain. The purpose of this study was to...

Hyrdology and water budget for a forested atlantic coastal plain watershed, South Carolina

Science.gov (United States)

Scott V. Harder; Devendra M. Amatya; Timothy J. Callahan; Carl C. Trettin; Jon Hakkila

2007-01-01

Increases in timber demand and urban development in the Atlantic Coastal Plain over the past decade have motivated studies on the hydrology, water quality, and sustainable management of coastal plain watersheds. However, studies on baseline water budgets are limited for the low-lying, forested watersheds of the Atlantic Coastal Plain. The purpose of this study was to...

A flexible electrode array for muscle impedance measurements in the mouse hind limb: A tool to speed research in neuromuscular disease

Science.gov (United States)

Li, J.; Rutkove, S. B.

2013-04-01

Electrical impedance myography (EIM) is a bioelectrical impedance technique focused on the assessment of neuromuscular diseases using tetrapolar surface arrays. Recently, we have shown that reproducible and sensitive EIM measurements can be made on the gastrocnemius muscle of the mouse hind limb and that these are sensitive to disease alterations. A dedicated array would help speed data acquisition and provide additional sensitivity to disease-induced alterations. A flexible electrode array was developed with electrode sizes of 1mm × 1mm by Parlex, Inc. Tetrapolar electrode sets were arranged both parallel to (longitudinal) and orthogonally to (transverse) the major muscle fiber direction of the gastrocnemius muscle. Measurements were made with a dedicated EIM system. A total of 11 healthy animals and 7 animals with spinal muscular atrophy (a form of motor neuron disease) were evaluated after the fur was completely removed with a depilatory agent from the hind limb. Standard electrophysiologic testing (compound motor action potential amplitude and motor unit number estimation) was also performed. The flexible electrode array demonstrated high repeatability in both the longitudinal and transverse directions in the healthy and diseased animals (with intraclass correlation coefficients of 0.94 and 0.89, respectively, for phase angle measured transversely). In addition, differences between healthy and diseased animals were identifiable. For example, the 50 kHz transverse phase angle was higher in the healthy as compared to the SMA animals (16.8° ± 0.5 vs. 14.3° ± 0.7, respectively) at 21 weeks of age (p = 0.01). Differences in anisotropy were also identifiable. Correlations to several standard neurophysiologic parameters also appeared promising. This novel flexible tetrapolar electrode array can be used on the mouse hind limb and provides multidirectional data that can be used to assess muscle health. This technique has the potential of finding widespread use in

A flexible electrode array for muscle impedance measurements in the mouse hind limb: A tool to speed research in neuromuscular disease

International Nuclear Information System (INIS)

Li, J; Rutkove, S B

2013-01-01

Electrical impedance myography (EIM) is a bioelectrical impedance technique focused on the assessment of neuromuscular diseases using tetrapolar surface arrays. Recently, we have shown that reproducible and sensitive EIM measurements can be made on the gastrocnemius muscle of the mouse hind limb and that these are sensitive to disease alterations. A dedicated array would help speed data acquisition and provide additional sensitivity to disease-induced alterations. A flexible electrode array was developed with electrode sizes of 1mm × 1mm by Parlex, Inc. Tetrapolar electrode sets were arranged both parallel to (longitudinal) and orthogonally to (transverse) the major muscle fiber direction of the gastrocnemius muscle. Measurements were made with a dedicated EIM system. A total of 11 healthy animals and 7 animals with spinal muscular atrophy (a form of motor neuron disease) were evaluated after the fur was completely removed with a depilatory agent from the hind limb. Standard electrophysiologic testing (compound motor action potential amplitude and motor unit number estimation) was also performed. The flexible electrode array demonstrated high repeatability in both the longitudinal and transverse directions in the healthy and diseased animals (with intraclass correlation coefficients of 0.94 and 0.89, respectively, for phase angle measured transversely). In addition, differences between healthy and diseased animals were identifiable. For example, the 50 kHz transverse phase angle was higher in the healthy as compared to the SMA animals (16.8° ± 0.5 vs. 14.3° ± 0.7, respectively) at 21 weeks of age (p = 0.01). Differences in anisotropy were also identifiable. Correlations to several standard neurophysiologic parameters also appeared promising. This novel flexible tetrapolar electrode array can be used on the mouse hind limb and provides multidirectional data that can be used to assess muscle health. This technique has the potential of finding widespread use in

Can we really measure the internal energy of hot nuclei with a 4 {pi} detection array?

Energy Technology Data Exchange (ETDEWEB)

Vient, E.; Genouin-Duhamel, E.; Steckmeyer, J.C. [and others

2001-10-01

The second generation of high quality detection arrays gave hope to nuclear physicists to finally obtain an experimental equation of state of nuclear matter. In spite of this progress, the measurement of the internal energy of a hot nucleus remains a very difficult task. This paper illustrates this difficulty by a methodological study of a classical technique of excitation energy measurement used in the Fermi energy range. The aim of this study is to verify the validity, the accuracy and the experimental limits of these measurements. It is shown that it is difficult to have a real experimental mastery of the source reconstruction and calorimetry at least for limited bombarding energies and violent collisions. (authors)

Can we really measure the internal energy of hot nuclei with a 4 π detection array?

International Nuclear Information System (INIS)

Vient, E.; Genouin-Duhamel, E.; Steckmeyer, J.C.

2001-10-01

The second generation of high quality detection arrays gave hope to nuclear physicists to finally obtain an experimental equation of state of nuclear matter. In spite of this progress, the measurement of the internal energy of a hot nucleus remains a very difficult task. This paper illustrates this difficulty by a methodological study of a classical technique of excitation energy measurement used in the Fermi energy range. The aim of this study is to verify the validity, the accuracy and the experimental limits of these measurements. It is shown that it is difficult to have a real experimental mastery of the source reconstruction and calorimetry at least for limited bombarding energies and violent collisions. (authors)

The reevaluation of plain roentgenological study in isolated splenic injury

International Nuclear Information System (INIS)

Kang, Seong Ihn; Ko, Seung Sook; Kim, Kil Jeong; Oh, Jae Hee; Kim, Young Chul

1986-01-01

The spleen is the most common intraabdominal organ injured in blunt trauma. Although physical signs and symptoms, coupled with abdominal paracentesis and peritoneal lavage confirm intraabdominal injury, but isolated splenic injury especially delayed rupture, the diagnosis and clinical course is variable. We are reevaluation of plain roentgenologic findings for the light of early diagnosis of isolated splenic injury. 24 patients of the autopsy and surgically proven isolated splenic injury at Chosun University Hospital in the period from 1980 January to 1986 June were analyzed plain roentgenogram retrospectively. The results were as follows: 1. Male patients predominate, constitution 87.5%. Incidence has been greatest in second to fourth decade. 2. Mode of trauma causing isolated splenic injury is most common in motor vehicle accident and others are fall down, struck by fist, blow to object, uncertain blunt trauma. 3. Delayed rupture of spleen occurred in 2 cases (8.3%). 4. Common patterns of splenic injury is simple laceration that involves both the capsule and the parenchyma and a laceration that involves the splenic pedicle. 5. Plain chest roentgenographic findings were abnormal in 4 cases (16.7%). The most common plain abdominal roentgenographic findings was the evidence of intaabdominal fluid in 21 cases (87.5%). The others are included in order of frequency; gastric dilatation, prominent mucosal folds on greater curvature of the stomach, evidence of pelvic fluid, displacement of stomach to the right or downward, mass density in the region of spleen. 6. No relationship can be shown between patterns of injury, time lapse after trauma and plain roentgenological findings. But the evidence of intraabdominal fluid is most important in the light of early diagnosis. 7. Diagnosis of splenic injury may be most helpful that in combination with clinical history, clinical symptoms and signs and plain film findings. In delayed rupture, diagnostic value of serial examination

The reevaluation of plain roentgenological study in isolated splenic injury

Energy Technology Data Exchange (ETDEWEB)

Kang, Seong Ihn; Ko, Seung Sook; Kim, Kil Jeong; Oh, Jae Hee; Kim, Young Chul [Chosun University College of Medicine, Gwangju (Korea, Republic of)

1986-10-15

The spleen is the most common intraabdominal organ injured in blunt trauma. Although physical signs and symptoms, coupled with abdominal paracentesis and peritoneal lavage confirm intraabdominal injury, but isolated splenic injury especially delayed rupture, the diagnosis and clinical course is variable. We are reevaluation of plain roentgenologic findings for the light of early diagnosis of isolated splenic injury. 24 patients of the autopsy and surgically proven isolated splenic injury at Chosun University Hospital in the period from 1980 January to 1986 June were analyzed plain roentgenogram retrospectively. The results were as follows: 1. Male patients predominate, constitution 87.5%. Incidence has been greatest in second to fourth decade. 2. Mode of trauma causing isolated splenic injury is most common in motor vehicle accident and others are fall down, struck by fist, blow to object, uncertain blunt trauma. 3. Delayed rupture of spleen occurred in 2 cases (8.3%). 4. Common patterns of splenic injury is simple laceration that involves both the capsule and the parenchyma and a laceration that involves the splenic pedicle. 5. Plain chest roentgenographic findings were abnormal in 4 cases (16.7%). The most common plain abdominal roentgenographic findings was the evidence of intaabdominal fluid in 21 cases (87.5%). The others are included in order of frequency; gastric dilatation, prominent mucosal folds on greater curvature of the stomach, evidence of pelvic fluid, displacement of stomach to the right or downward, mass density in the region of spleen. 6. No relationship can be shown between patterns of injury, time lapse after trauma and plain roentgenological findings. But the evidence of intraabdominal fluid is most important in the light of early diagnosis. 7. Diagnosis of splenic injury may be most helpful that in combination with clinical history, clinical symptoms and signs and plain film findings. In delayed rupture, diagnostic value of serial examination

Low-frequency synthesis array in earth orbit

International Nuclear Information System (INIS)

Jones, D.L.; Preston, R.A.; Kuiper, T.B.H.

1987-01-01

The scientific objectives and design concept of a space-based VLBI array for high-resolution astronomical observations at 1-30 MHz are discussed. The types of investigations calling for such an array include radio spectroscopy of individual objects, measurement of the effects of scattering and refraction by the interplanetary medium (IPM) and the ISM, mapping the distribution of low-energy cosmic-ray electrons, and determining the extent of the Galactic halo. Consideration is given to the limitations imposed on an LF VLBI array by the ionosphere, the IPM, and the ISM; the calibration advantages offered by circular polar orbits of slightly differing ascending-node longitude for the array satellites; and collection of the IF data streams from the array satellites by one master satellite prior to transmission to the ground. It is shown that determination of the three-dimensional array geometry by means of intersatellite radio links is feasible if there are at least seven spacecraft in the array

Determining the primary cosmic ray energy from the total flux of Cherenkov light measured at the Yakutsk EAS array

International Nuclear Information System (INIS)

Ivanov, A. A.; Knurenko, S. P.; Sleptsov, I. E.

2007-01-01

We present a method for determining the energy of the primary particle that generates an extensive air shower (EAS) of comic rays based on measuring the total flux of Cherenkov light from the shower. Applying this method to Cherenkov light measurements at the Yakutsk EAS array has allowed us to construct the cosmic ray energy spectrum in the range 10 15 - 3 x 10 19 eV

SAQC: SNP Array Quality Control

Directory of Open Access Journals (Sweden)

Li Ling-Hui

2011-04-01

Full Text Available Abstract Background Genome-wide single-nucleotide polymorphism (SNP arrays containing hundreds of thousands of SNPs from the human genome have proven useful for studying important human genome questions. Data quality of SNP arrays plays a key role in the accuracy and precision of downstream data analyses. However, good indices for assessing data quality of SNP arrays have not yet been developed. Results We developed new quality indices to measure the quality of SNP arrays and/or DNA samples and investigated their statistical properties. The indices quantify a departure of estimated individual-level allele frequencies (AFs from expected frequencies via standardized distances. The proposed quality indices followed lognormal distributions in several large genomic studies that we empirically evaluated. AF reference data and quality index reference data for different SNP array platforms were established based on samples from various reference populations. Furthermore, a confidence interval method based on the underlying empirical distributions of quality indices was developed to identify poor-quality SNP arrays and/or DNA samples. Analyses of authentic biological data and simulated data show that this new method is sensitive and specific for the detection of poor-quality SNP arrays and/or DNA samples. Conclusions This study introduces new quality indices, establishes references for AFs and quality indices, and develops a detection method for poor-quality SNP arrays and/or DNA samples. We have developed a new computer program that utilizes these methods called SNP Array Quality Control (SAQC. SAQC software is written in R and R-GUI and was developed as a user-friendly tool for the visualization and evaluation of data quality of genome-wide SNP arrays. The program is available online (http://www.stat.sinica.edu.tw/hsinchou/genetics/quality/SAQC.htm.

Clinical aspects of plain film radiography of the chest

International Nuclear Information System (INIS)

Ravin, C.E.

1988-01-01

In spite of the introduction of a number of intriguing new imaging modalities including Computed Tomography and Magnetic Resonance Imaging, the plain film of the chest remains the mainstay of thoracic imaging. It is estimated that more than fifty million chest radiographs are performed each year in the United States. In the attempt to compare newer imaging modalities with the standard plain film of the chest, investigators have been forced to adopt specific structures and or disease processes to be analyzed. To some extent identification of normally appearing structures in the mediastinum and lung parenchyma serves as a clue as to the ability of a newer technology to compete with or be compared with the plain film. However, as most authors would acknowledge, the ability to portray normal underlying anatomy is only the first step in analysis in intrathoracic disease. Experimental design becomes somewhat more complicated when one wishes to move beyond normal anatomy to analysis of disease processes. The challenge of digital radiography in whatever form it may take will be to equal or exceed the standard established by conventional plain film radiography and deliver such service at reasonable cost in a manner which allows for appropriate patient throughput

Nitrate retention in a sand plains stream and the importance of groundwater discharge

Science.gov (United States)

Robert S. Stelzer; Damion R. Drover; Susan L. Eggert; Maureen A. Muldoon

2011-01-01

We measured net nitrate retention by mass balance in a 700-m upwelling reach of a third-order sand plains stream, Emmons Creek, from January 2007 to November 2008. Surface water and ground-water fluxes of nitrate were determined from continuous records of discharge and from nitrate concentrations based on weekly and biweekly sampling at three surface water stations and...

Mapping Electrical Crosstalk in Pixelated Sensor Arrays

Science.gov (United States)

Seshadri, Suresh (Inventor); Cole, David (Inventor); Smith, Roger M. (Inventor); Hancock, Bruce R. (Inventor)

2017-01-01

The effects of inter pixel capacitance in a pixilated array may be measured by first resetting all pixels in the array to a first voltage, where a first image is read out, followed by resetting only a subset of pixels in the array to a second voltage, where a second image is read out, where the difference in the first and second images provide information about the inter pixel capacitance. Other embodiments are described and claimed.

Fundamentals of spherical array processing

CERN Document Server

Rafaely, Boaz

2015-01-01

This book provides a comprehensive introduction to the theory and practice of spherical microphone arrays. It is written for graduate students, researchers and engineers who work with spherical microphone arrays in a wide range of applications.   The first two chapters provide the reader with the necessary mathematical and physical background, including an introduction to the spherical Fourier transform and the formulation of plane-wave sound fields in the spherical harmonic domain. The third chapter covers the theory of spatial sampling, employed when selecting the positions of microphones to sample sound pressure functions in space. Subsequent chapters present various spherical array configurations, including the popular rigid-sphere-based configuration. Beamforming (spatial filtering) in the spherical harmonics domain, including axis-symmetric beamforming, and the performance measures of directivity index and white noise gain are introduced, and a range of optimal beamformers for spherical arrays, includi...

General practitioners' willingness to request plain lumbar spine radiographic examinations

International Nuclear Information System (INIS)

Ryynaenen, Olli-Pekka; Lehtovirta, Jukka; Soimakallio, Seppo; Takala, Jorma

2001-01-01

Objectives: To examine general practitioners' attitudes to plain lumbar spine radiographic examinations. Design: A postal questionnaire consisting of questions on background data and doctors' opinions about plain lumbar spine radiographic examinations, as well as eight vignettes (imaginary patient cases) presenting indications for lumbar radiography, and five vignettes focusing on the doctors' willingness to request lumbar radiography on the basis of patients' age and duration of symptoms. The data were analysed according to the doctor's age, sex, workplace and the medical school of graduation. Setting: Finland. Subjects: Six hundred and fifteen randomly selected physicians working in primary health care (64% of original target group). Results: The vignettes revealed that the use of plain lumbar radiographic examination varied between 26 and 88%. Patient's age and radiation protection were the most prominent factors influencing doctors' decisions to request lumbar radiographies. Only slight differences were observed between the attitudes of male and female doctors, as well as between young and older doctors. Doctors' willingness to request lumbar radiographies increased with the patient's age in most vignettes. The duration of patients' symptoms had a dramatic effect on the doctor's decision: in all vignettes, doctors were more likely to request lumbar radiography when patient's symptoms had exceeded 4 weeks. Conclusions: General practitioners commonly use plain lumbar spine radiographic examinations, despite its limited value in the diagnosis of low back pain. Further consensus and medical education is needed to clarify the indications for plain lumbar radiographic examination

Innovations in IR projector arrays

Science.gov (United States)

Cole, Barry E.; Higashi, B.; Ridley, Jeff A.; Holmen, J.; Newstrom, K.; Zins, C.; Nguyen, K.; Weeres, Steven R.; Johnson, Burgess R.; Stockbridge, Robert G.; Murrer, Robert Lee; Olson, Eric M.; Bergin, Thomas P.; Kircher, James R.; Flynn, David S.

2000-07-01

In the past year, Honeywell has developed a 512 X 512 snapshot scene projector containing pixels with very high radiance efficiency. The array can operate in both snapshot and raster mode. The array pixels have near black body characteristics, high radiance outputs, broad band performance, and high speed. IR measurements and performance of these pixels will be described. In addition, a vacuum probe station that makes it possible to select the best die for packaging and delivery based on wafer level radiance screening, has been developed and is in operation. This system, as well as other improvements, will be described. Finally, a review of the status of the present projectors and plans for future arrays is included.

Successive Standardization of Rectangular Arrays

Directory of Open Access Journals (Sweden)

Richard A. Olshen

2012-02-01

Full Text Available In this note we illustrate and develop further with mathematics and examples, the work on successive standardization (or normalization that is studied earlier by the same authors in [1] and [2]. Thus, we deal with successive iterations applied to rectangular arrays of numbers, where to avoid technical difficulties an array has at least three rows and at least three columns. Without loss, an iteration begins with operations on columns: first subtract the mean of each column; then divide by its standard deviation. The iteration continues with the same two operations done successively for rows. These four operations applied in sequence completes one iteration. One then iterates again, and again, and again, ... In [1] it was argued that if arrays are made up of real numbers, then the set for which convergence of these successive iterations fails has Lebesgue measure 0. The limiting array has row and column means 0, row and column standard deviations 1. A basic result on convergence given in [1] is true, though the argument in [1] is faulty. The result is stated in the form of a theorem here, and the argument for the theorem is correct. Moreover, many graphics given in [1] suggest that except for a set of entries of any array with Lebesgue measure 0, convergence is very rapid, eventually exponentially fast in the number of iterations. Because we learned this set of rules from Bradley Efron, we call it “Efron’s algorithm”. More importantly, the rapidity of convergence is illustrated by numerical examples.

Assessment of Embedded Conjugated Polymer Sensor Arrays for Potential Load Transmission Measurement in Orthopaedic Implants

Directory of Open Access Journals (Sweden)

Carolina Micolini

2017-11-01

Full Text Available Load transfer through orthopaedic joint implants is poorly understood. The longer-term outcomes of these implants are just starting to be studied, making it imperative to monitor contact loads across the entire joint implant interface to elucidate the force transmission and distribution mechanisms exhibited by these implants in service. This study proposes and demonstrates the design, implementation, and characterization of a 3D-printed smart polymer sensor array using conductive polyaniline (PANI structures embedded within a polymeric parent phase. The piezoresistive characteristics of PANI were investigated to characterize the sensing behaviour inherent to these embedded pressure sensor arrays, including the experimental determination of the stable response of PANI to continuous loading, stability throughout the course of loading and unloading cycles, and finally sensor repeatability and linearity in response to incremental loading cycles. This specially developed multi-material additive manufacturing process for PANI is shown be an attractive approach for the fabrication of implant components having embedded smart-polymer sensors, which could ultimately be employed for the measurement and analysis of joint loads in orthopaedic implants for in vitro testing.

A novel sensor array for field based ocular ultraviolet radiation measurements

International Nuclear Information System (INIS)

Fleming, D. P.; Walsh, J. E.; Moore, L. A.; Bergmanson, J. P.; McMahon, D.

2006-01-01

The intensification of terrestrial solar ultraviolet radiation (UVR) due to the diminution of the ozone layer has promoted a variety of research into establishing the impact of this elevated potential dose of UVR on biological tissues. Certain anterior ocular tissues have been found to be susceptible to damage by incident UVR and potentially blinding diseases such as pterygium are thought to be a direct result of absorbed UVR at the nasal limbus. There is a need for more accurate quantification and localisation of incident UVR at the anterior ocular surface. A novel solar blind photodiode sensor array system has been designed, constructed and tested for this purpose. Initial measurements to quantify the irradiance across the anterior ocular surface within the latitudes known as the 'pterygium belt' provide us with a set of core data for different head orientations and tilt angles and indicate the accuracy and stability of the system. (authors)

Cigarette packaging and health warnings: the impact of plain packaging and message framing on young smokers.

Science.gov (United States)

Mays, Darren; Niaura, Raymond S; Evans, W Douglas; Hammond, David; Luta, George; Tercyak, Kenneth P

2015-03-01

This study examined the impact of pictorial cigarette-warning labels, warning-label message framing and plain cigarette packaging, on young adult smokers' motivation to quit. Smokers aged 18-30 years (n=740) from a consumer research panel were randomised to one of four experimental conditions where they viewed online images of four cigarette packs with warnings about lung disease, cancer, stroke/heart disease and death, respectively. Packs differed across conditions by warning-message framing (gain vs loss) and packaging (branded vs plain). Measures captured demographics, smoking behaviour, covariates and motivation to quit in response to cigarette packs. Pictorial warnings about lung disease and cancer generated the strongest motivation to quit across conditions. Adjusting for pretest motivation and covariates, a message framing by packaging interaction revealed gain-framed warnings on plain packs generated greater motivation to quit for lung disease, cancer and mortality warnings (ppackaging regulations. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The experimental method of measurement for spatial distribution of full aperture backscatter light by circular PIN-array

International Nuclear Information System (INIS)

Zhao Xuefeng; Wang Chuanke; Hu Feng; Kuang Longyu; Wang Zhebin; Li Sanwei; Liu Shengye; Jiang Gang

2011-01-01

The spatial distribution of backscatter light is very important for understanding the production of backscatter light. The experimental method of spatial distribution of full aperture backscatter light is based on the circular PIN array composed of concentric orbicular multi-PIN detectors. The image of backscatter light spatial distribution of full aperture SBS is obtained by measuring spatial distribution of full aperture backscatter light using the method in the experiment of laser hohlraum targets interaction at 'Shenguang II'. A preliminary method to measure spatial distribution of full aperture backscatter light is established. (authors)

Smith-Purcell experiment utilizing a field-emitter array cathode measurements of radiation

CERN Document Server

Ishizuka, H; Yokoo, K; Shimawaki, H; Hosono, A

2001-01-01

Smith-Purcell (SP) radiation at wavelengths of 350-750 nm was produced in a tabletop experiment using a field-emitter array (FEA) cathode. The electron gun was 5 cm long, and a 25 mmx25 mm holographic replica grating was placed behind the slit provided in the anode. A regulated DC power supply accelerated electron beams in excess of 10 mu A up to 45 keV, while a small Van de Graaff generator accelerated smaller currents to higher energies. The grating had a 0.556 mu m period, 30 deg. blaze and a 0.2 mu m thick aluminum coating. Spectral characteristics of the radiation were measured both manually and automatically; in the latter case, the spectrometer was driven by a stepping motor to scan the wavelength, and AD-converted signals from a photomultiplier tube were processed by a personal computer. The measurement, made at 80 deg. relative to the electron beam, showed good agreement with theoretical wavelengths of the SP radiation. Diffraction orders were -2 and -3 for beam energies higher than 45 keV, -3 to -5 ...

Stochastic resolution analysis of co-prime arrays in radar

NARCIS (Netherlands)

Pribic, R; Coutiño Minguez, M.A.; Leus, G.J.T.

2016-01-01

Resolution from co-prime arrays and from a full ULA of the size equal to the virtual size of co-prime arrays is investigated. We take into account not only the resulting beam width but also the fact that fewer measurements are acquired by co-prime arrays. This fact is relevant in compressive

Diagnostic value of pneumoperitoneum on plain abdominal film

International Nuclear Information System (INIS)

Frkovic, M.; Klapan, T.; Moscatello, I.; Frkovic, M.

2001-01-01

Background. Pneumoperitoneum is the presence of air outside the gut lumen as the hallmark of alimentary tract perforation. It can be spontaneous or traumatic in origin. The most frequent cause of spontaneous pneumoperitoneum is the perforation of gastric or duodenal ulcer and the aim of the study was to assess the diagnostic value of pneumoperitoneum on plain abdominal film. Patients and methods. This is a retrospective study based on the diagnostic value of pneumoperitoneum on plain abdominal film, with the patient in upright, supine and sometimes left lateral decubitus position. The study included 79 patients who were admitted to our hospital during a 2-year period of time (1998- 1999) and operated on for perforated gastroduodenal ulcer. Results. Ten (12.66 %) of 79 patients underwent operation without radiological procedure. Sixty-nine (87.34 %) patients were examined radiographically and 53 (76.81 %) of them had signs of pneumoperitoneum initially on the plain film. Conclusions. The most common cause of pneumoperitoneum was perforated duodenal ulcer in elderly male patients. The most frequent sign of pneumoperitoneum was the crescent shaped free air beneath the diaphragm. (author)

Focal plane array with modular pixel array components for scalability

Science.gov (United States)

Kay, Randolph R; Campbell, David V; Shinde, Subhash L; Rienstra, Jeffrey L; Serkland, Darwin K; Holmes, Michael L

2014-12-09

A modular, scalable focal plane array is provided as an array of integrated circuit dice, wherein each die includes a given amount of modular pixel array circuitry. The array of dice effectively multiplies the amount of modular pixel array circuitry to produce a larger pixel array without increasing die size. Desired pixel pitch across the enlarged pixel array is preserved by forming die stacks with each pixel array circuitry die stacked on a separate die that contains the corresponding signal processing circuitry. Techniques for die stack interconnections and die stack placement are implemented to ensure that the desired pixel pitch is preserved across the enlarged pixel array.

First simultaneous space measurements of atmospheric pollutants in the boundary layer from IASI: A case study in the North China Plain

International Nuclear Information System (INIS)

Boynard, Anne; Safieddine, Sarah; Oudot, Charlotte; Hadji-Lazaro, Juliette; Clerbaux, Cathy; Clarisse, Lieven; Bauduin, Sophie; Hurtmans, Daniel; Coheur, Pierre-Francois; Pommier, Matthieu; Van Damme, Martin

2014-01-01

In this paper we investigate a severe pollution episode that occurred in Beijing, Tianjin, and the Hebei province in January 2013. The episode was caused by the combination of anthropogenic emissions and a high-pressure system that trapped pollutants in the boundary layer. Using IASI (Infrared Atmospheric Sounding Interferometer) satellite measurements, high concentrations of key trace gases such as carbon monoxide (CO), sulfur dioxide (SO 2 ), and ammonia (NH 3 ) along with ammonium sulfate aerosol ((NH 4 ) 2 SO 4 ) are found. We show that IASI is able to detect boundary layer pollution in case of large negative thermal contrast combined with high levels of pollution. Our findings demonstrate that anthropogenic key pollutants, such as CO and SO 2 , can be monitored by IASI in the North China Plain during wintertime in support of air quality evaluation and management. (authors)

41 CFR 102-2.140 - What elements of plain language appear in the FMR?

Science.gov (United States)

2010-07-01

... MANAGEMENT REGULATION SYSTEM Plain Language Regulatory Style § 102-2.140 What elements of plain language... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What elements of plain language appear in the FMR? 102-2.140 Section 102-2.140 Public Contracts and Property Management Federal...

Carpal pseudoerosions: a plain X-ray interpretation pitfall

Energy Technology Data Exchange (ETDEWEB)

Wawer, Richard [Univ. Catholique de Lille (France). Service d' Imagerie Medicale; Budzik, Jean Francois [Univ. Catholique de Lille (France). Service d' Imagerie Medicale; Univ. Nord de France, Boulogne sur Mer (France). Unite de Recherche EA 4490, Physiopathologie des Maladies Osseuses Inflammatoires; Demondion, Xavier [Univ. Lille 2 (France). Service d' Imagerie Musculosquelettique; CHRU Lille (France). Lab. d' Anatomie; Forzy, Gerard [Univ. Catholique de Lille, Lomme (France). Lab. de Biologie; Cotten, Anne [Univ. Lille 2 (France). Service d' Imagerie Musculosquelettique; Univ. Nord de France, Boulogne sur Mer (France). Unite de Recherche EA 4490, Physiopathologie des Maladies Osseuses Inflammatoires

2014-10-15

To examine in detail images of pseudoerosion of the wrist and hand on plain radiographs. The study was conducted with 28 cadaver wrists. During a single imaging session three techniques - plain radiography, tomosynthesis, and computed tomography - were used to visualize the wrist and hand specimens. For each technique, 20 radio-ulno-carpo-metacarpal sites known to present bone erosions in rheumatoid arthritis were analyzed by two radiologists using a standard system to score the cortical bone: normal, pseudoerosion, true erosion, or other pathology. Cohen's concordance analysis was performed to determine inter-observer and intra-observer (for the senior radiologist) agreement by site and by technique. Serial sections of two cadaver specimens were examined to determine the anatomical correlation of the pseudoerosions. On the plain radiographs, the radiologists scored many images as pseudoerosion (7.3 %), particularly in the distal ulnar portion of the capitate, the distal radial portion of the hamate, the proximal ulnar portion of the base of the third metacarpal, the proximal radial portion of the base of the fourth metacarpal, the distal ulnar portion of the hamate, and the proximal portion of the base of the fifth metacarpal. The computed tomography scan revealed that none of these doubtful images corresponded to true erosions. The anatomical correlation study showed that these images could probably be attributed to ligament insertions, thinner lamina, and enhanced cortical bone transparency. Knowledge of the anatomical carpal localizations where pseudoerosions commonly occur is a necessary prerequisite for analysis of plain radiographs performed to diagnose or monitor rheumatoid arthritis. (orig.)

An appraisal of plain language in the South African banking sector

African Journals Online (AJOL)

combination of approaches to plain language, but no testing is done on real consumers. ... language' definition in relation to other definitions of plain language, before the findings ... minimal experience as a consumer of the relevant goods or services, could be ..... The legal practitioner agreed by mentioning that marketing.

49 CFR 215.109 - Defective plain bearing box: Journal lubrication system.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective plain bearing box: Journal lubrication... Freight Car Components Suspension System § 215.109 Defective plain bearing box: Journal lubrication system...) Metal parts contacting the journal; or (e) Is— (1) Missing; or (2) Not in contact with the journal. ...

The role of plain radiographs in the diagnosis of chronic maxillary ...

African Journals Online (AJOL)

Background: Computed tomography is currently the gold standard for the diagnosis of chronic rhinosinusitis. However, this facility is not readily available in many developing countries. Thus, plain sinus radiography is still widely in use in our practice. Objectives: To assess the diagnostic value of plain radiographs in adult ...

Comparative Performance and Model Agreement of Three Common Photovoltaic Array Configurations.

Science.gov (United States)

Boyd, Matthew T

2018-02-01

Three grid-connected monocrystalline silicon arrays on the National Institute of Standards and Technology (NIST) campus in Gaithersburg, MD have been instrumented and monitored for 1 yr, with only minimal gaps in the data sets. These arrays range from 73 kW to 271 kW, and all use the same module, but have different tilts, orientations, and configurations. One array is installed facing east and west over a parking lot, one in an open field, and one on a flat roof. Various measured relationships and calculated standard metrics have been used to compare the relative performance of these arrays in their different configurations. Comprehensive performance models have also been created in the modeling software pvsyst for each array, and its predictions using measured on-site weather data are compared to the arrays' measured outputs. The comparisons show that all three arrays typically have monthly performance ratios (PRs) above 0.75, but differ significantly in their relative output, strongly correlating to their operating temperature and to a lesser extent their orientation. The model predictions are within 5% of the monthly delivered energy values except during the winter months, when there was intermittent snow on the arrays, and during maintenance and other outages.

Compressive Sensing for Millimeter Wave Antenna Array Diagnosis

KAUST Repository

Eltayeb, Mohammed E.

2018-01-08

The radiation pattern of an antenna array depends on the excitation weights and the geometry of the array. Due to wind and atmospheric conditions, outdoor millimeter wave antenna elements are subject to full or partial blockages from a plethora of particles like dirt, salt, ice, and water droplets. Handheld devices are also subject to blockages from random finger placement and/or finger prints. These blockages cause absorption and scattering to the signal incident on the array, modify the array geometry, and distort the far-field radiation pattern of the array. This paper studies the effects of blockages on the far-field radiation pattern of linear arrays and proposes several array diagnosis techniques for millimeter wave antenna arrays. The proposed techniques jointly estimate the locations of the blocked antennas and the induced attenuation and phase-shifts given knowledge of the angles of arrival/departure. Numerical results show that the proposed techniques provide satisfactory results in terms of fault detection with reduced number of measurements (diagnosis time) provided that the number of blockages is small compared to the array size.

Timed arrays wideband and time varying antenna arrays

CERN Document Server

Haupt, Randy L

2015-01-01

Introduces timed arrays and design approaches to meet the new high performance standards The author concentrates on any aspect of an antenna array that must be viewed from a time perspective. The first chapters briefly introduce antenna arrays and explain the difference between phased and timed arrays. Since timed arrays are designed for realistic time-varying signals and scenarios, the book also reviews wideband signals, baseband and passband RF signals, polarization and signal bandwidth. Other topics covered include time domain, mutual coupling, wideband elements, and dispersion. The auth

Superdirective Magnetic Dipole Array as a First-Order Probe for Spherical Near-Field Antenna Measurements

DEFF Research Database (Denmark)

Kim, Oleksiy S.; Pivnenko, Sergey; Breinbjerg, Olav

2012-01-01

The theory as well as numerical and experimental results are presented for a superdirective array composed of closely spaced electrically small resonant magnetic dipole elements. The array operates on a metal ground plane and can exhibit a maximum directivity of 11.5 dBi, 15.2 dBi, and 17.8 d......Bi (including 3 dB due to the ground plane), for 2, 3, and 4 magnetic dipoles, respectively. The array is self-resonant and is directly excited by a 50-ohm coaxial cable through the ground plane. The array radiates essentially the $\\vert\\mu\\vert=1$ spherical modes, which, despite a narrow bandwidth, makes...

The case for the plain packaging of tobacco products.

Science.gov (United States)

Freeman, Becky; Chapman, Simon; Rimmer, Matthew

2008-04-01

The Framework Convention on Tobacco Control (FCTC) requires nations that have ratified the convention to ban all tobacco advertising and promotion. In the face of these restrictions, tobacco packaging has become the key promotional vehicle for the tobacco industry to interest smokers and potential smokers in tobacco products. This paper reviews available research into the probable impact of mandatory plain packaging and internal tobacco industry statements about the importance of packs as promotional vehicles. It critiques legal objections raised by the industry about plain packaging violating laws and international trade agreements. Searches for available evidence were conducted within the internal tobacco industry documents through the online document archives; tobacco industry trade publications; research literature through the Medline and Business Source Premier databases; and grey literature including government documents, research reports and non-governmental organization papers via the Google internet search engine. Plain packaging of all tobacco products would remove a key remaining means for the industry to promote its products to billions of the world's smokers and future smokers. Governments have required large surface areas of tobacco packs to be used exclusively for health warnings without legal impediment or need to compensate tobacco companies. Requiring plain packaging is consistent with the intention to ban all tobacco promotions. There is no impediment in the FCTC to interpreting tobacco advertising and promotion to include tobacco packs.

Tests of operating conditions for metrological application of HTS Josephson arrays

International Nuclear Information System (INIS)

Sosso, A; Lacquaniti, V; Andreone, D; Cerri, R; Klushin, A M

2006-01-01

We report on an experimental study of metrological properties of High Temperature Superconductor arrays, made of shunted bicrystal YBCO Josephson junctions, to assess their accuracy. A detailed analysis of measurement errors is presented, mainly based on a direct comparison of an HTS array against a low temperature array. Owing to the high sensitivity of the comparison, we were able to measure the changes in the HTS array voltage on a step at nanovolt level. A precise estimate of the dependence of the HTS array step width on operating conditions was obtained. Differences were observed with respect to the results provided by the usual, low sensitivity, techniques, confirming that the method we adopted is necessary in the study of HTS arrays for metrology. The high sensitivity analysis was applied in the derivation of the temperature dependence of the critical current as well, providing some insights on the behaviour of the HTS array

Space and power efficient hybrid counters array

Science.gov (United States)

Gara, Alan G [Mount Kisco, NY; Salapura, Valentina [Chappaqua, NY

2009-05-12

A hybrid counter array device for counting events. The hybrid counter array includes a first counter portion comprising N counter devices, each counter device for receiving signals representing occurrences of events from an event source and providing a first count value corresponding to a lower order bits of the hybrid counter array. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits of the hybrid counter array. A control device monitors each of the N counter devices of the first counter portion and initiates updating a value of a corresponding second count value stored at the corresponding addressable memory location in the second counter portion. Thus, a combination of the first and second count values provide an instantaneous measure of number of events received.

24-71 GHz PCB Array for 5G ISM

Science.gov (United States)

Novak, Markus H.; Volakis, John L.; Miranda, Felix A.

2017-01-01

Millimeter-wave 5G mobile architectures need to consolidate disparate frequency bands into a single, multifunctional array. Existing arrays are either narrow-band, prohibitively expensive or cannot be scaled to these frequencies. In this paper, we present the first ultra-wideband millimeter wave array to operate across six 5G and ISM bands spanning 24-71 GHz. Importantly, the array is realized using low-cost PCB. The paper presents the design and optimized layout, and discusses fabrication and measurements.

Long-range magnetostatic interactions in arrays of nanowires

CERN Document Server

Raposo, V; González, J M; Vázquez, M

2000-01-01

Experimental measurements and micromagnetic simulations of the hysteresis loops of arrays of cobalt nanowires are compared here. Arrays of cobalt nanowires (200 nm in diameter) were electrodeposited into the pores of alumina membranes (thickness 60 mu m). Their hysteresis loops along the axial direction of nanowires were measured using vibrating sample magnetometry. Micromagnetic simulations were performed considering dipolar interaction between nanowires leading to similar hysteresis loops as those obtained experimentally.

ArrayBridge: Interweaving declarative array processing with high-performance computing

Energy Technology Data Exchange (ETDEWEB)

Xing, Haoyuan [The Ohio State Univ., Columbus, OH (United States); Floratos, Sofoklis [The Ohio State Univ., Columbus, OH (United States); Blanas, Spyros [The Ohio State Univ., Columbus, OH (United States); Byna, Suren [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Prabhat, Prabhat [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wu, Kesheng [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Brown, Paul [Paradigm4, Inc., Waltham, MA (United States)

2017-05-04

Scientists are increasingly turning to datacenter-scale computers to produce and analyze massive arrays. Despite decades of database research that extols the virtues of declarative query processing, scientists still write, debug and parallelize imperative HPC kernels even for the most mundane queries. This impedance mismatch has been partly attributed to the cumbersome data loading process; in response, the database community has proposed in situ mechanisms to access data in scientific file formats. Scientists, however, desire more than a passive access method that reads arrays from files. This paper describes ArrayBridge, a bi-directional array view mechanism for scientific file formats, that aims to make declarative array manipulations interoperable with imperative file-centric analyses. Our prototype implementation of ArrayBridge uses HDF5 as the underlying array storage library and seamlessly integrates into the SciDB open-source array database system. In addition to fast querying over external array objects, ArrayBridge produces arrays in the HDF5 file format just as easily as it can read from it. ArrayBridge also supports time travel queries from imperative kernels through the unmodified HDF5 API, and automatically deduplicates between array versions for space efficiency. Our extensive performance evaluation in NERSC, a large-scale scientific computing facility, shows that ArrayBridge exhibits statistically indistinguishable performance and I/O scalability to the native SciDB storage engine.

Review: Recharge rates and chemistry beneath playas of the High Plains aquifer, USA

Science.gov (United States)

Gurdak, Jason J.; Roe, Cassia D.

2010-12-01

Playas are ephemeral, closed-basin wetlands that are hypothesized as an important source of recharge to the High Plains aquifer in central USA. The ephemeral nature of playas, low regional recharge rates, and a strong reliance on groundwater from the High Plains aquifer has prompted many questions regarding the contribution and quality of recharge from playas to the High Plains aquifer. As a result, there has been considerable scientific debate about the potential for water to infiltrate the relatively impermeable playa floors, travel through the unsaturated zone sediments that are tens of meters thick, and subsequently recharge the High Plains aquifer. This critical review examines previously published studies on the processes that control recharge rates and chemistry beneath playas. Reported recharge rates beneath playas range from less than 1.0 to more than 500 mm/yr and are generally 1-2 orders of magnitude higher than recharge rates beneath interplaya settings. Most studies support the conceptual model that playas are important zones of recharge to the High Plains aquifer and are not strictly evaporative pans. The major findings of this review provide science-based implications for management of playas and groundwater resources of the High Plains aquifer and directions for future research.

Proactive monitoring of a wind turbine array with lidar measurements, SCADA data and a data-driven RANS solver

Science.gov (United States)

Iungo, G.; Said, E. A.; Santhanagopalan, V.; Zhan, L.

2016-12-01

Power production of a wind farm and durability of wind turbines are strongly dependent on non-linear wake interactions occurring within a turbine array. Wake dynamics are highly affected by the specific site conditions, such as topography and local atmospheric conditions. Furthermore, contingencies through the life of a wind farm, such as turbine ageing and off-design operations, make prediction of wake interactions and power performance a great challenge in wind energy. In this work, operations of an onshore wind turbine array were monitored through lidar measurements, SCADA and met-tower data. The atmospheric wind field investing the wind farm was estimated by using synergistically the available data through five different methods, which are characterized by different confidence levels. By combining SCADA data and the lidar measurements, it was possible to estimate power losses connected with wake interactions. For this specific array, power losses were estimated to be 4% and 2% of the total power production for stable and convective atmospheric regimes, respectively. The entire dataset was then leveraged for the calibration of a data-driven RANS (DDRANS) solver for prediction of wind turbine wakes and power production. The DDRANS is based on a parabolic formulation of the Navier-Stokes equations with axisymmetry and boundary layer approximations, which allow achieving very low computational costs. Accuracy in prediction of wind turbine wakes and power production is achieved through an optimal tuning of the turbulence closure model. The latter is based on a mixing length model, which was developed based on previous wind turbine wake studies carried out through large eddy simulations and wind tunnel experiments. Several operative conditions of the wind farm under examination were reproduced through DDRANS for different stability regimes, wind directions and wind velocity. The results show that DDRANS is capable of achieving a good level of accuracy in prediction

Response of Competing Vegetation to Site Preparation on West Gulf Coastal Plain Commercial Forest Land

Science.gov (United States)

Gale L. Wolters; Henry A. Pearson; Ronald E. Thill; V. Clark Baldwin; Alton Martin

1995-01-01

The response of woody and herbaceous vegetation to site preparation, subsoil texture, and fertilization was measured on the West Gulf Coastal Plain. The influences of these treatments on competing vegetation were short-term. Drastic soil disturbance and fertilization briefly increased herbage production. Shear-windrow and shear-disk were generally the most effective...

Validation of a Piezoelectric Sensor Array-Based Device for Measurement of Carotid-Femoral Pulse Wave Velocity: The Philips Prototype.

Science.gov (United States)

Xu, Shao-Kun; Hong, Xiang-Fei; Cheng, Yi-Bang; Liu, Chang-Yuan; Li, Yan; Yin, Bin; Wang, Ji-Guang

2018-03-01

Multiple piezoelectric pressure mechanotransducers topologized into an array might improve efficiency and accuracy in collecting arterial pressure waveforms for measurement of pulse wave velocity (PWV). In the present study, we validated a piezoelectric sensor array-based prototype (Philips) against the validated and clinically widely used Complior device (Alam Medical). We recruited 33 subjects with a wide distribution of PWV. For the validation, PWV was measured sequentially with the Complior device (four times) and the Philips prototype (three times). With the 99 paired PWV values, we investigated the agreement between the Philips prototype and the Complior device using Pearson correlation analysis and Bland-Altman plot. We also performed analysis on the determinants and reproducibility of PWV measured with both devices. The correlation coefficient for PWV measured with the two devices was 0.92 ( p prototype slightly overestimated PWV by 0.24 (± 2 standard deviations, ± 1.91) m/s, especially when PWV was high. The correlation coefficient between the difference and the average of the Philips and Complior measurements was 0.21 ( p = 0.035). Nonetheless, they had similar determinants. Age, mean arterial pressure, and sex altogether explained 81.6 and 83.9% of the variance of PWV values measured with the Philips prototype and Complior device, respectively. When the two extremes of the three PWV values measured with the Philips prototype and the Complior device were investigated, the coefficients of variation were 8.26 and 3.26%, respectively. Compared with the Complior device, the Philips prototype had similar accuracy, determinants, and reproducibility in measuring PWV.

The Southwest Configuration for the Next Generation Very Large Array

Science.gov (United States)

Irwin Kellermann, Kenneth; Carilli, Chris; Condon, James; Cotton, William; Murphy, Eric Joseph; Nyland, Kristina

2018-01-01

We discuss the planned array configuration for the Next Generation Very Large Array (ngVLA). The configuration, termed the "Southwest Array," consists of 214 antennas each 18 m in diameter, distributed over the Southwest United States and Northern Mexico. The antenna locations have been set applying rough real-world constraints, such as road, fiber, and power access. The antenna locations will be fixed, with roughly 50% of the antennas in a "core" of 2 km diameter, located at the site of the JVLA. Another 30% of the antennas will be distributed over the Plains of San Augustin to a diameter of 30 km, possibly along, or near, the current JVLA arms. The remaining 20% of the antennas will be distributed in a rough two-arm spiral pattern to the South and East, out to a maximum distance of 500 km, into Texas, Arizona, and Chihuahua. Years of experience with the VLA up to 50 GHz, plus intensive antenna testing up to 250 GHz for the ALMA prototype antennas, verify the VLA site as having very good observing conditions (opacity, phase stability), up to 115 GHz (ngVLA Memo No. 1). Using a suite of tools implemented in CASA, we have made extensive imaging simulations with this configuration. We find that good imaging performance can be obtained through appropriate weighting of the visibilities, for resolutions ranging from that of the core of the array (1" at 30 GHz), out to the longest baselines (10 mas at 30 GHz), with a loss of roughly a factor of two in sensitivity relative to natural weighting (ngVLA Memo No. 16). The off-set core, located on the northern edge of the long baseline configuration, provides excellent sensitivity even on the longest baselines. We are considering, in addition, a compact configuration of 16 close-packed 6 m antennas to obtain uv-coverage down to baselines ~ 10 m for imaging large scale structure, as well as a configuration including 9 stations distributed to continental scales.

Visualisation of air–water bubbly column flow using array Ultrasonic Velocity Profiler

Directory of Open Access Journals (Sweden)

Munkhbat Batsaikhan

2017-11-01

Full Text Available In the present work, an experimental study of bubbly two-phase flow in a rectangular bubble column was performed using two ultrasonic array sensors, which can measure the instantaneous velocity of gas bubbles on multiple measurement lines. After the sound pressure distribution of sensors had been evaluated with a needle hydrophone technique, the array sensors were applied to two-phase bubble column. To assess the accuracy of the measurement system with array sensors for one and two-dimensional velocity, a simultaneous measurement was performed with an optical measurement technique called particle image velocimetry (PIV. Experimental results showed that accuracy of the measurement system with array sensors is under 10% for one-dimensional velocity profile measurement compared with PIV technique. The accuracy of the system was estimated to be under 20% along the mean flow direction in the case of two-dimensional vector mapping.

Aerosol Activation Properties within and above Mixing Layer in the North China Plain

Science.gov (United States)

Deng, Z.; Ran, L.

2013-12-01

Aerosol particles, serving as cloud condensation nuclei (CCN), may modify the properties of clouds and have an impact on climate. The vertical distribution of aerosols and their activation properties is critical to quantify the effect of aerosols on clouds. An intensive field campaign, Vertical Observations of trace Gases and Aerosols in the North China Plain (VOGA-NCP 2013), was conducted in the North China Plain during the late July and early August 2013 to measure the vertical profiles of atmospheric components in this polluted region and estimate their effects on atmospheric environment and climate. Aerosols were measured with in-situ instruments and Lidar. Particularly, the aerosols were collected at 1000 m height with a 1 m3 bag sampler attached to a tethered balloon, and subsequently measured with combined scanning mobility particle sizer (SMPS) and CCN counter. Comparisons of size-resolved activation ratios at ground level and 1000 m height showed that aerosols in upper atmosphere were not only less concentrated, but also less CCN-active than those at the surface. The difference in aerosol properties between upper atmosphere and the ground indicates that the analysis of impacts of aerosols on cloud might be misleading in heavily polluted region based on the relationship of cloud properties and surface aerosols or column without considering the vertical distribution of aerosol activation abilities.

Genetics, medicine, and the Plain people.

Science.gov (United States)

Strauss, Kevin A; Puffenberger, Erik G

2009-01-01

The Old Order Amish and Old Order Mennonite populations of Pennsylvania are descended from Swiss Anabaptist immigrants who came to the New World in the early eighteenth century. Today they live in many small endogamous demes across North America. Genetically, these demes have dissimilar allele frequencies and disease spectra owing to unique founders. Biological and social aspects of Old Order communities make them ideal for studies in population genetics and genomic medicine, and over the last 40 years, advances in genomic science coincided with investigational studies in Plain populations. Newer molecular genetic technologies are sufficiently informative, rapid, and flexible to use in a clinical setting, and we have successfully integrated these tools into a rural pediatric practice. Our studies with the Pennsylvania Plain communities show that population-specific genetic knowledge provides a powerful framework in which to prevent disease, reduce medical costs, and create new insights into human biology.

Thermal crosstalk in heated microcantilever arrays

International Nuclear Information System (INIS)

Kim, Hoe Joon; Dai, Zhenting; King, William P

2013-01-01

We report on a detailed characterization and analysis of thermal crosstalk in a heated microcantilever array. The fabricated heated cantilever array consists of five identical independently controlled heated cantilevers. The temperature of each cantilever can be controlled over a large temperature range, up to 900 °C, by means of an integrated solid-state resistive heater. We analyze thermal crosstalk in steady and transient operating conditions when the heated cantilever array is either in contact with a substrate or freely suspended in air. The thermal conductance between neighboring cantilevers is as high as 0.61 µW °C −1 , resulting in non-negligible temperature increases in neighboring cantilevers, depending upon the operating conditions. By understanding and accounting for thermal crosstalk, it is possible to improve temperature control and temperature measurements with heated microcantilever arrays. (paper)

The Status of the Telescope Array experiment

Energy Technology Data Exchange (ETDEWEB)

Tokuno, H; Azuma, R [Tokyo Institute of Technology, Meguro, Tokyo (Japan); Abu-Zayyad, T; Allen, M; Barcikowski, E; Belz, J W; Blake, S A; Brusova, O; Cady, R [University of Utah, High Energy Astrophysics Institute, Salt Lake City, Utah (United States); Aida, R [University of Yamanashi, Interdisciplinary Graduate School of Medicine and Engineering, Kofu, Yamanashi (Japan); Benno, T; Chikawa, M; Doura, K [Kinki University, Higashi Osaka, Osaka (Japan); Bergman, D R [Rutgers University, Piscataway (United States); Cheon, B G; Cho, E J [Hanyang University, Seongdong-gu, Seoul (Korea, Republic of); Chiba, J [Tokyo University of Science, Noda, Chiba (Japan); Cho, L S; Cho, W R [Yonsei University, Seodaemun-gu, Seoul (Korea, Republic of); Cohen, F, E-mail: htokuno@cr.phys.titech.ac.jp [Institute for Cosmic Ray Research, University of Tokyo, Kashiwa, Chiba (Japan)

2011-04-01

The purpose of The Telescope Array experiment is to identify origin of the ultra high energy cosmic rays. The Telescope Array is a hybrid detector consists of a surface detector array and air fluorescence detectors. This hybrid detector is observing extensive air showers to measure the energy spectrum, anisotropy and composition of Ultra High Energy Cosmic Rays. The detector construction has been completed in March 2008, and the hybrid observation with the full configuration has been running since that time. In this talk, the status of observation and our prospects are described.

Measurement of central nickel density in Doublet III plasmas with a soft x-ray diode array

International Nuclear Information System (INIS)

Groebner, R.J.; Jahns, G.L.; Ejima, S.; Hsieh, C.L.

1985-01-01

An array of soft x-ray diodes has been used to obtain central nickel densities for discharges in the Doublet III tokamak, during operation with an inconel primary limiter, in which nickel L-line radiation dominated the diode signals. The nature of the diode signals is determined primarily by comparison with soft x-ray spectra. The contribution of the continuum portion of the spectra to the central diode signal can be calculated and compared to the observed signal. When the diode signal is dominated by nickel L-line emission, the observed signal is considerably larger than the calculated continuum contribution. Chordal data from the array of diodes are inverted to provide the spatial profile of soft x-ray emission. Because the diodes are absolute detectors of radiation, the soft x-ray emission profile is used to obtain the absolute nickel concentration and density profile in the center of the plasma. A computer code, including over 100 nickel L-line transitions, has been developed to obtain the nickel density. The nickel L-line cooling rate, calculated with the code, is presented. The nickel density obtained by this technique agrees well with that obtained from the K/sub α/ line intensity measured with a soft x-ray spectrometer and that obtained from a bolometric measurement of central radiated power coupled with a coronal equilibrium model of the radiation

Harsh Environment Gas Sensor Array for Venus Atmospheric Measurements, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Makel Engineering and the Ohio State University propose to develop a harsh environment tolerant gas sensor array for atmospheric analysis in future Venus missions....

Distribution, typology and assessment of degraded soils Piedmont Plains Zhetysu Ridge, Kazakhstan

Directory of Open Access Journals (Sweden)

Maira Kussainova

2017-04-01

Full Text Available Identification of land degradation is essential to check the problem and to implement the remedial measures needed. The study area falls under parts of foothill plains Zhetysu Ridge, Kazakhstan, that is an arid region in climate. Recent data on the status of study area refer to the 80s of the last century, and the intensive use of them led to a significant anthropogenic transformation. This study was carried out in 2015-2016 as part of a project aimed to study features and causes of land degradation in foothill plains Zhetysu Ridge, Kazakhstan. Under the conditions of rainfed soil degradation manifests itself in the development of erosion processes, agro depletion of soils, reducing the productivity of agriculture. The use of land for irrigation often accompanied by secondary salinization. In this regard, at present there is need to assess current state of the soil, with the identification of changes in their properties as a result of the impact of various anthropogenic factors and creation of new electronic soil maps and applied the powerful capabilities of advanced remote sensing (RS and geographic information system (GIS techniques to identify the geomorphological units and degradation risk assessment. Satellite imagery in addition to the field and laboratory studies to identify salinity-induced soil degradation was adopted in this study. Morphological, chemical and physical characteristics of soils in degraded sites in foothill plains Zhetysu Ridge, Kazakhstan, were depicted. The main results of a thorough evaluation of soil degradation in foothill plains Zhetysu Ridge, Kazakhstan, are presented. The data revealed that extent of salinity-induced degradation was generally related to some physical properties of soil, uncontrolled livestock grazing and previous soil management practices. These results are useful as the basis for designing soil conservation and restoration programs, as a base line for evaluating the performance of conservation

Savannah River Region: Transition between the Gulf and Atlantic Coastal Plains. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Zullo, V.A.; Harris, W.B.; Price, V. [eds.

1990-12-31

The focus of the this conference of Coastal Plains geologists was on the Savannah River region of Georgia and South Carolina, and particularly on the geology of the US Department of Energy`s 300 square mile Savannah River Site (SRS) in western South Carolina. Current geological studies indicate that the Mesozoic-Cenozoic section in the Savannah River region is transitional between that of the Gulf Coastal Plain to the southwest and that of the Atlantic Coastal Plain to the northeast. With the transitional aspect of the region as its theme, the first session was devoted to overviews of Cretaceous and Paleogene geology in the Gulf and Atlantic Coastal Plains. Succeeding presentations and resulting discussions dealt with more specific problems in structural, lithostratigraphic, hydrological, biostratigraphic, and cyclostratigraphic analysis, and of correlation to standard stratigraphic frameworks. For these conference proceedings, individual papers have been processed separately for the Energy Data Base.

Effects of plain packaging on decision-making and reward for nicotine cigarettes

Directory of Open Access Journals (Sweden)

Martin LE

2014-05-01

Full Text Available Laura E Martin1,21Hoglund Brain Imaging Center, 2Department of Preventive Medicine and Public Health, University of Kansas Medical Center, Kansas City, KS, USAAbstract: Cigarette smoking remains the leading preventable cause of death worldwide. Efforts to reduce smoking prevalence include changes to policies that are expected to have impacts on smoking behaviors. Plain packaging has been introduced as a method to reduce the appeal of smoking by removing such branding information as pack colors and brand logos from cigarette packages. Behavioral studies of plain packaging demonstrate reductions in the appeal of cigarette packages, changes in smoking behaviors, and expected reductions in smoking initiation. Neuroimaging studies of branding demonstrate that the neural systems of rewards and cognitive control are associated with processing brand information (eg, logos. Neuroimaging studies in smokers demonstrate that the neural systems of reward respond to images of cigarettes and are associated with reductions in cognitive control responses. The current review discusses the state of research on plain packaging in terms of a biopsychosocial model of addiction in which behavioral studies of plain packaging can identify psychological and social changes related to packaging, whereas neuroimaging studies can identify biological changes underlying the psychological and social impacts of packaging. Together, these studies show that plain packaging may reduce positive perceptions of smoking by reducing related reward responses in the brain, thus increasing the likelihood that smokers will be able to resist the urge to smoke, and perhaps quit smoking altogether.Keywords: smoking, plain packaging, neuroimaging, branding, reward

Integrated power conditioning for laser diode arrays

International Nuclear Information System (INIS)

Hanks, R.L.; Kirbie, H.C.; Newton, M.A.; Farhoud, M.S.

1995-01-01

This compact modulator has demonstated its ability to efficiently and accurately drive a laser diode array. The addition of the crowbar protection circuit is an invaluable addition to the integrated system and is capable of protecting the laser diode array against severe damage. We showed that the correlation between measured data and simulation indicates that our modulator model is valid and can be used as a tool in the design of future systems. The spectrometer measurements that we conducted underline the imprtance of current regulation to stable laser operation

Analysis of Surface Electric Field Measurements from an Array of Electric Field Mills

Science.gov (United States)

Lucas, G.; Thayer, J. P.; Deierling, W.

2016-12-01

Kennedy Space Center (KSC) has operated an distributed array of over 30 electric field mills over the past 18 years, providing a unique data set of surface electric field measurements over a very long timespan. In addition to the electric field instruments there are many meteorological towers around KSC that monitor the local meteorological conditions. Utilizing these datasets we have investigated and found unique spatial and temporal signatures in the electric field data that are attributed to local meteorological effects and the global electric circuit. The local and global scale influences on the atmospheric electric field will be discussed including the generation of space charge from the ocean surf, local cloud cover, and a local enhancement in the electric field that is seen at sunrise.

High Altitude Infrasound Measurements using Balloon-Borne Arrays

Science.gov (United States)

Bowman, D. C.; Johnson, C. S.; Gupta, R. A.; Anderson, J.; Lees, J. M.; Drob, D. P.; Phillips, D.

2015-12-01

For the last fifty years, almost all infrasound sensors have been located on the Earth's surface. A few experiments consisting of microphones on poles and tethered aerostats comprise the remainder. Such surface and near-surface arrays likely do not capture the full diversity of acoustic signals in the atmosphere. Here, we describe results from a balloon mounted infrasound array that reached altitudes of up to 38 km (the middle stratosphere). The balloon drifted at the ambient wind speed, resulting in a near total reduction in wind noise. Signals consistent with tropospheric turbulence were detected. A spectral peak in the ocean microbarom range (0.12 - 0.35 Hz) was present on balloon-mounted sensors but not on static infrasound stations near the flight path. A strong 18 Hz signal, possibly related to building ventilation systems, was observed in the stratosphere. A wide variety of other narrow band acoustic signals of uncertain provenance were present throughout the flight, but were absent in simultaneous recordings from nearby ground stations. Similar phenomena were present in spectrograms from the last balloon infrasound campaign in the 1960s. Our results suggest that the infrasonic wave field in the stratosphere is very different from that which is readily detectable on surface stations. This has implications for modeling acoustic energy transfer between the lower and upper atmosphere as well as the detection of novel acoustic signals that never reach the ground. Our work provides valuable constraints on a proposed mission to detect earthquakes on Venus using balloon-borne infrasound sensors.

Concentration and distribution patterns of naturally occurring radionuclides in sediments and flood plain soils of the catchment area of the river Elbe

International Nuclear Information System (INIS)

Barth, A.; Jurk, M.; Weiß, D.

1998-01-01

The impact of uranium mining and milling as well as that of traditional mining activities on river sediments and flood plain soils in the catchment area of the river Elbe was investigated over the years 1994 to 1995. Contamination resulting from mining activities has been identified by comparing the median values for the measured radionuclides, and by establishing the ratio between Ra-226 and Ra-228. The transport and deposition of contaminated materials as a result of high water events, and river discharge of waste water from mining and milling facilities, can be considered to be the main paths of sediment and soil contamination. Sediments and flood plain soils located in the vicinity of former uranium mining and milling sites are primarily influenced by discharges of waste water. Long distance transport and deposition at dams, barrages and on flood plains has mainly been caused by high water events. In many cases the radionuclide concentrations were higher in the subsurface layer than in the top layer of flood plain soil. Due to termination of uranium mining and milling activities, no significant contamination of newer or fresh sediments was found. Radiation exposure arising in relation to angling or walking on flood plains is low

Redshift measurement of Fermi blazars for the Cherenkov telescope array

Science.gov (United States)

Pita, S.; Goldoni, P.; Boisson, C.; Cotter, G.; Lefaucheur, J.; Lenain, J.-P.; Lindfors, E.; Williams, D. A.

2017-01-01

Blazars are active galactic nuclei, and the most numerous High Energy (HE) and Very High Energy (VHE) γ-ray emitters. Their optical emission is often dominated by non-thermal, and, in the case of BL Lacs, featureless continuum radiation. This makes the determination of their redshift extremely difficult. Indeed, as of today only about 50% of γ-ray blazars have a measured spectroscopic redshift. The knowledge of redshift is fundamental because it allows the precise modeling of the VHE emission and also of its interaction with the extragalactic background light (EBL). The beginning of the Cherenkov Telescope Array (CTA) operations in the near future will allow the detection of several hundreds of new blazars. Using the Fermi catalogue of sources above 50 GeV (2FHL), we performed simulations which indicate that a significant fraction of the 2FHL blazars detectable by CTA will not have a measured redshift. As a matter of fact, the organization of observing campaigns to measure the redshift of these blazars has been recognized as a necessary support for the AGN Key Science Project of CTA. We are planning such an observing campaign. In order to optimize our chances of success, we will perform preliminary deep imaging observations aimed at detecting or setting upper limits to the host galaxy. We will then take spectra of the candidates with the brightest host galaxies. Taking advantage of the recent success of an X-shooter GTO observing campaign, these observations will be different with respect to previous ones due to the use of higher resolution spectrographs and of 8 meter class telescopes. We are starting to submit proposals for these observations. In this paper we briefly describe how candidates are selected and the corresponding observation program.

Detector array for measurement of high-frequency fluctuations in visible and near-UV emission from tokamaks

International Nuclear Information System (INIS)

Hurwitz, P.D.; Hall, B.F.; Rowan, W.L.

1992-01-01

We developed an imaging detector to measure high-frequency fluctuations in visible and near-UV emission from tokamaks. The detector is intended for the study of plasma turbulence, mhd phenomena, and edge-localized modes. Particularly in the first two applications, it will complement existing techniques by providing higher spatial resolution as well as measurement capability in otherwise inaccessible regions of the plasma. The device consists of an optical system, a linear array of 32 photodiodes, and an amplifier for each photodiode. The amplifiers have a transimpedance gain of 10 5 --10 6 and the frequency response is flat to 100 kHz. Experience with this device has shown that optical imaging systems can be easily designed and tailored to a specific measurement because of the small size and close spacing of the individual light-sensitive elements. The device has been successfully tested on TEXT-U in measurements of H α fluctuations

Proceedings of the Flat-Plate Solar Array Project Research Forum on the Design of Flat-Plate Photovoltaic Arrays for Central Stations

Science.gov (United States)

1983-01-01

The Flat Plate Solar Array Project, focuses on advancing technologies relevant to the design and construction of megawatt level central station systems. Photovoltaic modules and arrays for flat plate central station or other large scale electric power production facilities require the establishment of a technical base that resolves design issues and results in practical and cost effective configurations. Design, qualification and maintenance issues related to central station arrays derived from the engineering and operating experiences of early applications and parallel laboratory reserch activities are investigated. Technical issues are examined from the viewpoint of the utility engineer, architect/engineer and laboratory researcher. Topics on optimum source circuit designs, module insulation design for high system voltages, array safety, structural interface design, measurements, and array operation and maintenance are discussed.

flexural improvement of plain concrete beams strengthened

African Journals Online (AJOL)

Muhammad Nura Isa

Results show significant improvement in both stiffness and load bearing capacity of plain concrete ... Various methods have been developed to increase their strength capacity by using .... obtained by carrying out uniaxial direct tensile strength.

Cultural Landscape and Tourism Potential in the Transylvanian Plain

Directory of Open Access Journals (Sweden)

WILFRIED SCHREIBER

2007-01-01

Full Text Available Contradicting the general belief that the Transylvanian Plain has a poor tourism potential, we bring proof that even in a non-tourist region there are many elements that can provide a generous support for a variety of tourism activities, such as: rural tourism, agro-tourism, recreational tourism, cultural and religious tourism, eco-tourism, and even the critical tourism may occur if the resources are not properly managed. Definitions, examples, two tables, and a map are offering additional information and data, in order to reveal a less known side of the Transylvanian Plain.

Cantilever arrayed blood pressure sensor for arterial applanation tonometry.

Science.gov (United States)

Lee, Byeungleul; Jeong, Jinwoo; Kim, Jinseok; Kim, Bonghwan; Chun, Kukjin

2014-03-01

The authors developed a cantilever-arrayed blood pressure sensor array fabricated by (111) silicon bulk-micromachining for the non-invasive and continuous measurement of blood pressure. The blood pressure sensor measures the blood pressure based on the change in the resistance of the piezoresistor on a 5-microm-thick-arrayed perforated membrane and 20-microm-thick metal pads. The length and the width of the unit membrane are 210 and 310 microm, respectively. The width of the insensible zone between the adjacent units is only 10 microm. The resistance change over contact force was measured to verify the performance. The good linearity of the result confirmed that the polydimethylsiloxane package transfers the forces appropriately. The measured sensitivity was about 4.5%/N. The maximum measurement range and the resolution of the fabricated blood pressure sensor were greater than 900 mmHg (= 120 kPa) and less than 1 mmHg (= 133.3 Pa), respectively.

Crosstalk analysis of silicon-on-insulator nanowire-arrayed waveguide grating

International Nuclear Information System (INIS)

Li Kai-Li; An Jun-Ming; Zhang Jia-Shun; Wang Yue; Wang Liang-Liang; Li Jian-Guang; Wu Yuan-Da; Yin Xiao-Jie; Hu Xiong-Wei

2016-01-01

The factors influencing the crosstalk of silicon-on-insulator (SOI) nanowire arrayed waveguide grating (AWG) are analyzed using the transfer function method. The analysis shows that wider and thicker arrayed waveguides, outsider fracture of arrayed waveguide, and larger channel space, could mitigate the deterioration of crosstalk. The SOI nanowire AWGs with different arrayed waveguide widths are fabricated by using deep ultraviolet lithography (DUV) and inductively coupled plasma etching (ICP) technology. The measurement results show that the crosstalk performance is improved by about 7 dB through adopting 800 nm arrayed waveguide width. (paper)

Dense Array Optimization of Cross-Flow Turbines

Science.gov (United States)

Scherl, Isabel; Strom, Benjamin; Brunton, Steven; Polagye, Brian

2017-11-01

Cross-flow turbines, where the axis of rotation is perpendicular to the freestream flow, can be used to convert the kinetic energy in wind or water currents to electrical power. By taking advantage of mean and time-resolved wake structures, the optimal density of an array of cross-flow turbines has the potential for higher power output per unit area of land or sea-floor than an equivalent array of axial-flow turbines. In addition, dense arrays in tidal or river channels may be able to further elevate efficiency by exploiting flow confinement and surface proximity. In this work, a two-turbine array is optimized experimentally in a recirculating water channel. The spacing between turbines, as well as individual and coordinated turbine control strategies are optimized. Array efficiency is found to exceed the maximum efficiency for a sparse array (i.e., no interaction between turbines) for stream-wise rotor spacing of less than two diameters. Results are discussed in the context of wake measurements made behind a single rotor.

Template-based fabrication of nanowire-nanotube hybrid arrays

International Nuclear Information System (INIS)

Ye Zuxin; Liu Haidong; Schultz, Isabel; Wu Wenhao; Naugle, D G; Lyuksyutov, I

2008-01-01

The fabrication and structure characterization of ordered nanowire-nanotube hybrid arrays embedded in porous anodic aluminum oxide (AAO) membranes are reported. Arrays of TiO 2 nanotubes were first deposited into the pores of AAO membranes by a sol-gel technique. Co nanowires were then electrochemically deposited into the TiO 2 nanotubes to form the nanowire-nanotube hybrid arrays. Scanning electron microscopy and transmission electron microscopy measurements showed a high nanowire filling factor and a clean interface between the Co nanowire and the TiO 2 nanotube. Application of these hybrids to the fabrication of ordered nanowire arrays with highly controllable geometric parameters is discussed

Sub-threshold wavelength splitting in coupled photonic crystal cavity arrays

DEFF Research Database (Denmark)

Schubert, Martin; Frandsen, Lars Hagedorn; Skovgård, Troels Suhr

Coupled photonic crystal (PhC) cavity arrays have recently been found to increase the output power of nanocavity lasers by coherent coupling of a large number of cavities [1]. We have measured the sub-threshold behaviour of such structures in order to gain better understanding of the mode structure....... PhC structures defined by circular holes placed in a quadratic lattice with pitch a=280 nm were fabricated in a GaAs membrane and cavity arrays were realized by introducing single missing holes with intracavity hole distances of two, three, five and seven holes. Arrays with different number...... of coupled cavities were fabricated and characterized using photoluminescence measurements of quantum dots embedded in the GaAs PhC membrane. Since the collection spot size was ~2.5 μm and therefore small compared to the arrays, spectra were taken at several positions of each array....

Estimation of groundwater recharge using the chloride mass-balance method, Pingtung Plain, Taiwan

Science.gov (United States)

Ting, Cheh-Shyh; Kerh, Tienfuan; Liao, Chiu-Jung

Due to rapid economic growth in the Pingtung Plain of Taiwan, the use of groundwater resources has changed dramatically. Over-pumping of the groundwater reservoir, which lowers hydraulic heads in the aquifers, is not only affecting the coastal area negatively but has serious consequences for agriculture throughout the plain. In order to determine the safe yield of the aquifer underlying the plain, a reliable estimate of groundwater recharge is desirable. In the present study, for the first time, the chloride mass-balance method is adopted to estimate groundwater recharge in the plain. Four sites in the central part were chosen to facilitate the estimations using the ion-chromatograph and Thiessen polygon-weighting methods. Based on the measured and calculated results, in all sites, including the mountain and river boundaries, recharge to the groundwater is probably 15% of the annual rainfall, excluding recharge from additional irrigation water. This information can improve the accuracy of future groundwater-simulation and management models in the plain. Résumé Du fait de la croissance économique rapide de la plaine de Pingtung à Taiwan, l'utilisation des ressources en eau souterraine s'est considérablement modifié. La surexploitation des aquifères, qui a abaissé le niveau des nappes, n'affecte pas seulement la région côtière, mais a de sérieuses répercutions sur l'agriculture dans toute la plaine. Afin de déterminer les ressources renouvelables de l'aquifère sous la plaine, une estimation précise de la recharge de la nappe est nécessaire. Dans cette étude, le taux de recharge de la nappe a d'abord été estimé au moyen d'un bilan de matière de chlorure. Quatre sites de la partie centrale ont été sélectionnés pour réaliser ces estimations, à l'aide d'un chromatographe ionique et de la méthode des polygones de Thiessen. A partir des résultats mesurés et calculés, à chaque site, et en prenant comme limites les montagnes et les rivi

Exploring perception of Indians about plain packaging of tobacco products: a mixed method research

Directory of Open Access Journals (Sweden)

Monika eArora

2013-09-01

Full Text Available This study assessed perceptions and support among the Indian populace about plain packaging for all tobacco products.12 focus group discussions (n=124, stakeholder analysis with 24 officials and an opinion poll with 346 participants were conducted between December 2011 - May 2012 , Delhi. Plain packages for tobacco products were favoured by majority of participants (69% and key stakeholders (92%. The majority of participants perceived that plain packaging would reduce the appeal and promotional value of the tobacco pack (>80%, prevent initiation of tobacco use among children and youth (>60%, motivate tobacco users to quit (>80%, increase noticeability and effectiveness of pictorial health warnings on tobacco packs (>90%,reduce tobacco usage (75% of key stakeholders. Majority of participants favoured light grey colour for plain packaging. This study provides key evidence to advocate with Indian Government and other countries in South Asia region to introduce plain packaging legislation for all tobacco products.

Array signal processing in the NASA Deep Space Network

Science.gov (United States)

Pham, Timothy T.; Jongeling, Andre P.

2004-01-01

In this paper, we will describe the benefits of arraying and past as well as expected future use of this application. The signal processing aspects of array system are described. Field measurements via actual tracking spacecraft are also presented.

Moored current meter data from the Madeira Abyssal Plain (GME). 1. deployment (1984)

International Nuclear Information System (INIS)

Saunders, P.M.

1986-01-01

Near bottom current have been measured at three closely spaced sites in the N.E. Atlantic for 13 months. Locations were selected in the Great Meteor East study site area, near 31 0 30'N 25 0 W, one on the abyssal plain, one on top of a small abyssal hill about 400 m high and one on its flank just above the plain. Current meters were moored 10, 100, and 1000 m above the local bottom (5438 m, 5398 m and 4999 m) in January 1984 and recovered in February 1985. This report displays the characteristics of the currents in numerous tables and figures. In the mean they ar found to be very weak and though adjacent moorings are separated by only 12 km and 27 km the year-long current directions differ radically. Current variations are principally due to semi-diurnal tides, inertial oscillations and eddies the latter of which migrate over the moorings. The tidal energy meets expectations as does the eddy energy with magnitude 2-3 cm 2 s -2 . Horizontal (isopycnal) diffusivity is estimated as about 2x10 2 m 2 s -1 . Currents 10 m above the bottom exceed 10 cm/s least frequently on the plain and most frequently at the hill-foot. The influence of the hill is surprisingly large. At all three sites the strongest currents are found near the sea bed. Speeds also show a Weibull distribution and rough 50 year return currents are inferred. (author)

Neural mechanisms underlying visual attention to health warnings on branded and plain cigarette packs

Science.gov (United States)

Brooks, Jonathan C. W.; Munafò, Marcus R.; Leonards, Ute

2017-01-01

Abstract Aims To (1) test if activation in brain regions related to reward (nucleus accumbens) and emotion (amygdala) differ when branded and plain packs of cigarettes are viewed, (2) test whether these activation patterns differ by smoking status and (3) examine whether activation patterns differ as a function of visual attention to health warning labels on cigarette packs. Design Cross‐sectional observational study combining functional magnetic resonance imaging (fMRI) with eye‐tracking. Non‐smokers, weekly smokers and daily smokers performed a memory task on branded and plain cigarette packs with pictorial health warnings presented in an event‐related design. Setting Clinical Research and Imaging Centre, University of Bristol, UK. Participants Non‐smokers, weekly smokers and daily smokers (n = 72) were tested. After exclusions, data from 19 non‐smokers, 19 weekly smokers and 20 daily smokers were analysed. Measurements Brain activity was assessed in whole brain analyses and in pre‐specified masked analyses in the amygdala and nucleus accumbens. On‐line eye‐tracking during scanning recorded visual attention to health warnings. Findings There was no evidence for a main effect of pack type or smoking status in either the nucleus accumbens or amygdala, and this was unchanged when taking account of visual attention to health warnings. However, there was evidence for an interaction, such that we observed increased activation in the right amygdala when viewing branded as compared with plain packs among weekly smokers (P = 0.003). When taking into account visual attention to health warnings, we observed higher levels of activation in the visual cortex in response to plain packaging compared with branded packaging of cigarettes (P = 0.020). Conclusions Based on functional magnetic resonance imaging and eye‐tracking data, health warnings appear to be more salient on ‘plain’ cigarette packs than branded packs. PMID:27886656

Description of plant communities on the Red Sea costal plain of Sudan

NARCIS (Netherlands)

Woldewahid, G.; Werf, van der W.; Sykora, K.V.; Abate, T.; Mostofa, B.; Huis, van A.

2007-01-01

The coastal plains of the Red Sea constitute an important breeding area for the desert locust, Schistocerca gregaria. Vegetation analysis was undertaken in the coastal plain of Sudan to provide a frame of reference for studies on desert locust ecology and distribution. Vegetation relevés (>60 in

Summertime Low-Level Jets over the Great Plains

Energy Technology Data Exchange (ETDEWEB)

Stensrud, D.J. [NOAA/ERL/National Severe Storms Lab., Norman, OK (United States); Pfeifer, S. [Univ. of Oklahoma, Norman, OK (United States)

1996-04-01

The sky over the southern Great Plains Cloud and Atmospheric Radiation Testbed (CART) site of the Atmospheric Radiation Measurement (ARM) Program during the predawn and early morning hours often is partially obstructed by stratocumulus, stratus fractus, or cumulus fractus that are moving rapidly to the north, even through the surface winds are weak. This cloud movement is evidence of the low-level jet (LLJ), a wind speed maximum that occurs in the lowest few kilometers of the atmosphere. Owing to the wide spacing between upper-air sounding sites and the relatively infrequent sounding launches, LLJ evolution has been difficult to observe adequately, even though the effects of LLJs on moisture flux into North America are large. Model simulation of the LLJ is described.

Array Detector Modules for Spent Fuel Verification

Energy Technology Data Exchange (ETDEWEB)

Bolotnikov, Aleksey

2018-05-07

Brookhaven National Laboratory (BNL) proposes to evaluate the arrays of position-sensitive virtual Frisch-grid (VFG) detectors for passive gamma-ray emission tomography (ET) to verify the spent fuel in storage casks before storing them in geo-repositories. Our primary objective is to conduct a preliminary analysis of the arrays capabilities and to perform field measurements to validate the effectiveness of the proposed array modules. The outcome of this proposal will consist of baseline designs for the future ET system which can ultimately be used together with neutrons detectors. This will demonstrate the usage of this technology in spent fuel storage casks.

Measurement of changes in linear accelerator photon energy through flatness variation using an ion chamber array

International Nuclear Information System (INIS)

Gao Song; Balter, Peter A.; Rose, Mark; Simon, William E.

2013-01-01

Purpose: To compare the use of flatness versus percent depth dose (PDD) for determining changes in photon beam energy for a megavoltage linear accelerator. Methods: Energy changes were accomplished by adjusting the bending magnet current by up to ±15% in 5% increments away from the value used clinically. Two metrics for flatness, relative flatness in the central 80% of the field (Flat) and average maximum dose along the diagonals normalized by central axis dose (F DN ), were measured using a commercially available planner ionization chamber array. PDD was measured in water at depths of 5 and 10 cm in 3 × 3 cm 2 and 10 × 10 cm 2 fields using a cylindrical chamber. Results: PDD was more sensitive to changes in energy when the beam energy was increased than when it was decreased. For the 18-MV beam in particular, PDD was not sensitive to energy reductions below the nominal energy. The value of Flat was found to be more sensitive to decreases in energy than to increases, with little sensitivity to energy increases above the nominal energy for 18-MV beams. F DN was the only metric that was found to be sensitive to both increases and reductions of energy for both the 6- and 18-MV beams. Conclusions: Flatness based metrics were found to be more sensitive to energy changes than PDD, In particular, F DN was found to be the most sensitive metric to energy changes for photon beams of 6 and 18 MV. The ionization chamber array allows this metric to be conveniently measured as part of routine accelerator quality assurance.

Radiation fibrosis : differentiation from true hilar mass on plain chest film

International Nuclear Information System (INIS)

Baik, Jun Hyun; Ahn, Kook Jin; Park, Seog Hee; Shinn, Kyung Sub

1996-01-01

Radiation-induced fibrotic mass might masquerade as a true hilar tumor mass on a plain chest radiograph. We attempted to differentiate radiation fibrosis from a true hilar tumor using only a plain radiograph. Plain chest radiographs were obtained from seven patients who had developed radiation fibrosis simulating hilar mass after radiation therapy for lung cancer, and from 19 patients with lung cancer, a comparison group, who had not received radiation therapy. They were reviewed for the obliteration of the overlapped mediastinal and hilar anatomical silhouettes by the mass : pulmonary artery, heart or aorta border, and paraspinal line. All seven patients with radiation-induced fibrotic mass(bilateral lesion in two patients) showed obliteration of all three overlapped anatomical silhouettes of the mediastinum and hilum on chest radiographs. In the comparison group of 19 patients with a true hilar mass, there was, however, no case which demonstrated obliteration of all landmarks, Obliteration of all anatomical landmarks at the hilum and mediastinum may be a helpful clue in the differential diagnosis of radiation-induced fibrotic mass from true hilar mass on a plain radiograph, particularly when clinical information on previous radiation therapy is unavailable

CAUSES: Attribution of Surface Radiation Biases in NWP and Climate Models near the U.S. Southern Great Plains

Science.gov (United States)

Van Weverberg, K.; Morcrette, C. J.; Petch, J.; Klein, S. A.; Ma, H.-Y.; Zhang, C.; Xie, S.; Tang, Q.; Gustafson, W. I.; Qian, Y.; Berg, L. K.; Liu, Y.; Huang, M.; Ahlgrimm, M.; Forbes, R.; Bazile, E.; Roehrig, R.; Cole, J.; Merryfield, W.; Lee, W.-S.; Cheruy, F.; Mellul, L.; Wang, Y.-C.; Johnson, K.; Thieman, M. M.

2018-04-01

Many Numerical Weather Prediction (NWP) and climate models exhibit too warm lower tropospheres near the midlatitude continents. The warm bias has been shown to coincide with important surface radiation biases that likely play a critical role in the inception or the growth of the warm bias. This paper presents an attribution study on the net radiation biases in nine model simulations, performed in the framework of the CAUSES project (Clouds Above the United States and Errors at the Surface). Contributions from deficiencies in the surface properties, clouds, water vapor, and aerosols are quantified, using an array of radiation measurement stations near the Atmospheric Radiation Measurement Southern Great Plains site. Furthermore, an in-depth analysis is shown to attribute the radiation errors to specific cloud regimes. The net surface shortwave radiation is overestimated in all models throughout most of the simulation period. Cloud errors are shown to contribute most to this overestimation, although nonnegligible contributions from the surface albedo exist in most models. Missing deep cloud events and/or simulating deep clouds with too weak cloud radiative effects dominate in the cloud-related radiation errors. Some models have compensating errors between excessive occurrence of deep cloud but largely underestimating their radiative effect, while other models miss deep cloud events altogether. Surprisingly, even the latter models tend to produce too much and too frequent afternoon surface precipitation. This suggests that rather than issues with the triggering of deep convection, cloud radiative deficiencies are related to too weak convective cloud detrainment and too large precipitation efficiencies.

Depth-of-interaction measurement in a single-layer crystal array with a single-ended readout using digital silicon photomultiplier

International Nuclear Information System (INIS)

Lee, Min Sun; Lee, Jae Sung

2015-01-01

We present the first experimental evaluation of a depth-of-interaction (DOI) positron emission tomography (PET) detector using a digital silicon photomultiplier (dSiPM). To measure DOI information from a mono-layer array of scintillation crystals with a single-ended readout, our group has previously proposed and developed a new method based on light spread using triangular reflectors. Since this method relies on measurement of the light distribution, dSiPM, which has a fully digital interface, has several merits for our DOI measurement. The DOI PET detector comprised of a dSiPM sensor (DPC-3200-22-44) coupled with a 14   ×   14 array of 2 mm  ×  2 mm  ×  20 mm unpolished LGSO crystals. All crystals were covered with triangular reflectors. To obtain a good performance of the DOI PET detector, several parameters of detector were selected as a preliminary experiment. Detector performance was evaluated with the selected parameters and the optimal experimental setup, and a DOI measurement was conducted by irradiating the crystal block at five DOI positions spaced at intervals of 4 mm. Maximum-likelihood estimation was employed for DOI positioning and the optimal DOI estimation scheme was also investigated in this study. As a result, the DOI PET detector showed clear crystal identification. The energy resolution (full-width at half-maximum (FWHM)) averaged over all depths was 10.21%  ±  0.15% at 511 keV, and time resolution averaged over all depths was 1198.61   ±   39.70 ps FWHM. The average DOI positioning accuracy for all depths was 74.22%  ±  6.77%, which equates to DOI resolution of 4.67 mm. Energy and DOI resolutions were uniform over all crystal positions except for the back parts of the array. Furthermore, additional simulation studies were conducted to verify the results of our DOI measurement method that is combined with dSiPM technology. In conclusion, our continuous DOI PET detector

Quantitative measurements of ground state atomic oxygen in atmospheric pressure surface micro-discharge array

Science.gov (United States)

Li, D.; Kong, M. G.; Britun, N.; Snyders, R.; Leys, C.; Nikiforov, A.

2017-06-01

The generation of atomic oxygen in an array of surface micro-discharge, working in atmospheric pressure He/O2 or Ar/O2 mixtures, is investigated. The absolute atomic oxygen density and its temporal and spatial dynamics are studied by means of two-photon absorption laser-induced fluorescence. A high density of atomic oxygen is detected in the He/O2 mixture with up to 10% O2 content in the feed gas, whereas the atomic oxygen concentration in the Ar/O2 mixture stays below the detection limit of 1013 cm-3. The measured O density near the electrode under the optimal conditions in He/1.75% O2 gas is 4.26  ×  1015 cm-3. The existence of the ground state O (2p 4 3 P) species has been proven in the discharge at a distance up to 12 mm away from the electrodes. Dissociative reactions of the singlet O2 with O3 and deep vacuum ultraviolet radiation, including the radiation of excimer \\text{He}2\\ast , are proposed to be responsible for O (2p 4 3 P) production in the far afterglow. A capability of the surface micro-discharge array delivering atomic oxygen to long distances over a large area is considered very interesting for various biomedical applications.

Pin-photodiode array for the measurement of fan-beam energy and air kerma distributions of X-ray CT scanners.

Science.gov (United States)

Haba, Tomonobu; Koyama, Shuji; Aoyama, Takahiko; Kinomura, Yutaka; Ida, Yoshihiro; Kobayashi, Masanao; Kameyama, Hiroshi; Tsutsumi, Yoshinori

2016-07-01

Patient dose estimation in X-ray computed tomography (CT) is generally performed by Monte Carlo simulation of photon interactions within anthropomorphic or cylindrical phantoms. An accurate Monte Carlo simulation requires an understanding of the effects of the bow-tie filter equipped in a CT scanner, i.e. the change of X-ray energy and air kerma along the fan-beam arc of the CT scanner. To measure the effective energy and air kerma distributions, we devised a pin-photodiode array utilizing eight channels of X-ray sensors arranged at regular intervals along the fan-beam arc of the CT scanner. Each X-ray sensor consisted of two plate type of pin silicon photodiodes in tandem - front and rear photodiodes - and of a lead collimator, which only allowed X-rays to impinge vertically to the silicon surface of the photodiodes. The effective energy of the X-rays was calculated from the ratio of the output voltages of the photodiodes and the dose was calculated from the output voltage of the front photodiode using the energy and dose calibration curves respectively. The pin-photodiode array allowed the calculation of X-ray effective energies and relative doses, at eight points simultaneously along the fan-beam arc of a CT scanner during a single rotation of the scanner. The fan-beam energy and air kerma distributions of CT scanners can be effectively measured using this pin-photodiode array. Copyright © 2016 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Oriented Mn-doped CuO nanowire arrays

International Nuclear Information System (INIS)

Han, Dongqiang; Wu, Zhaofeng; Wang, Zhihe; Yang, Shaoguang

2016-01-01

Using anodic aluminum oxide membranes as the nanoreactors and controller, oriented nanowire arrays of the diluted magnetic semiconductor Mn-doped CuO have been successfully fabricated using Mn(NO_3)_2 · 4H_2O and Cu(NO_3)_2 · 3H_2O as the starting materials. X-ray diffraction measurements showed that the as-prepared oriented nanowire arrays are of high purity. Scanning electron microscope and transmission electron microscope studies showed the nanowires are oriented, continuous and uniform with a diameter and length of about 170 nm and several tens of micrometers, respectively, and thus of a high aspect ratio. Low-temperature magnetic measurements showed the ferromagnetic property of the oriented Mn-doped CuO nanowire arrays with the critical temperature at around 80 K, which will endow them with great potential applications in spintronics in the future. (paper)

General practitioners' willingness to request plain lumbar spine radiographic examinations

Energy Technology Data Exchange (ETDEWEB)

Ryynaenen, Olli-Pekka E-mail: ollipekka.ryynanen@uku.fi; Lehtovirta, Jukka; Soimakallio, Seppo; Takala, Jorma

2001-01-01

Objectives: To examine general practitioners' attitudes to plain lumbar spine radiographic examinations. Design: A postal questionnaire consisting of questions on background data and doctors' opinions about plain lumbar spine radiographic examinations, as well as eight vignettes (imaginary patient cases) presenting indications for lumbar radiography, and five vignettes focusing on the doctors' willingness to request lumbar radiography on the basis of patients' age and duration of symptoms. The data were analysed according to the doctor's age, sex, workplace and the medical school of graduation. Setting: Finland. Subjects: Six hundred and fifteen randomly selected physicians working in primary health care (64% of original target group). Results: The vignettes revealed that the use of plain lumbar radiographic examination varied between 26 and 88%. Patient's age and radiation protection were the most prominent factors influencing doctors' decisions to request lumbar radiographies. Only slight differences were observed between the attitudes of male and female doctors, as well as between young and older doctors. Doctors' willingness to request lumbar radiographies increased with the patient's age in most vignettes. The duration of patients' symptoms had a dramatic effect on the doctor's decision: in all vignettes, doctors were more likely to request lumbar radiography when patient's symptoms had exceeded 4 weeks. Conclusions: General practitioners commonly use plain lumbar spine radiographic examinations, despite its limited value in the diagnosis of low back pain. Further consensus and medical education is needed to clarify the indications for plain lumbar radiographic examination.

Experimental investigation of the ribbon-array ablation process

International Nuclear Information System (INIS)

Li Zhenghong; Xu Rongkun; Chu Yanyun; Yang Jianlun; Xu Zeping; Ye Fan; Chen Faxin; Xue Feibiao; Ning Jiamin; Qin Yi; Meng Shijian; Hu Qingyuan; Si Fenni; Feng Jinghua; Zhang Faqiang; Chen Jinchuan; Li Linbo; Chen Dingyang; Ding Ning; Zhou Xiuwen

2013-01-01

Ablation processes of ribbon-array loads, as well as wire-array loads for comparison, were investigated on Qiangguang-1 accelerator. The ultraviolet framing images indicate that the ribbon-array loads have stable passages of currents, which produce axially uniform ablated plasma. The end-on x-ray framing camera observed the azimuthally modulated distribution of the early ablated ribbon-array plasma and the shrink process of the x-ray radiation region. Magnetic probes measured the total and precursor currents of ribbon-array and wire-array loads, and there exists no evident difference between the precursor currents of the two types of loads. The proportion of the precursor current to the total current is 15% to 20%, and the start time of the precursor current is about 25 ns later than that of the total current. The melting time of the load material is about 16 ns, when the inward drift velocity of the ablated plasma is taken to be 1.5 × 10 7 cm/s.

Determining the Appropriate Economic Strategy to Conserve Groundwater Resources in Qazvin Plain

Directory of Open Access Journals (Sweden)

Abozar Parhizkari

2016-02-01

Full Text Available Qazvin plain is one of the capable plains in Iran to produce of agricultural goods. Unfortunately, due to inordinate shafts digging and irregular use of groundwater the level of groundwater has been decreased during two last decades so that water balance is negative now. To conserve the groundwater resources in this plain, strategies and appropriate policies are needed and this requires a better understanding of farmers’ behavior. Therefore, in the present study in order to investigate farmers' behavior in using of groundwater and determine appropriate strategies to conserve of groundwater resources in Qazvin plain, positive mathematical programming and production function with constant elasticity of substitution were used. The investigated strategies included increase in water price, decrease in water availability and deficit irrigation strategy and were investigated under various scenarios. The required data were registered information related to 2011-2012 collected from relevant departments in Qazvin province. The model was solved using GAMS 23/9 software. The results showed that all the investigated strategies led to water saving however the average gross profit changes decreased by 3.13, 8.61 and 5.54 percent with increasing water price, decrease in water availability and deficit irrigation, respectively. Finally, considering the less reduction in average gross profit, the irrigation water pricing and then deficit irrigation strategies were proposed to conserve groundwater resources in Qazvin plain.

A long-term study of aerosol–cloud interactions and their radiative effect at the Southern Great Plains using ground-based measurements

Directory of Open Access Journals (Sweden)

E. T. Sena

2016-09-01

Full Text Available Empirical estimates of the microphysical response of cloud droplet size distribution to aerosol perturbations are commonly used to constrain aerosol–cloud interactions in climate models. Instead of empirical microphysical estimates, here macroscopic variables are analyzed to address the influence of aerosol particles and meteorological descriptors on instantaneous cloud albedo and the radiative effect of shallow liquid water clouds. Long-term ground-based measurements from the Atmospheric Radiation Measurement (ARM program over the Southern Great Plains are used. A broad statistical analysis was performed on 14 years of coincident measurements of low clouds, aerosol, and meteorological properties. Two cases representing conflicting results regarding the relationship between the aerosol and the cloud radiative effect were selected and studied in greater detail. Microphysical estimates are shown to be very uncertain and to depend strongly on the methodology, retrieval technique and averaging scale. For this continental site, the results indicate that the influence of the aerosol on the shallow cloud radiative effect and albedo is weak and that macroscopic cloud properties and dynamics play a much larger role in determining the instantaneous cloud radiative effect compared to microphysical effects. On a daily basis, aerosol shows no correlation with cloud radiative properties (correlation = −0.01 ± 0.03, whereas the liquid water path shows a clear signal (correlation = 0.56 ± 0.02.

Pannonian plain as a morphostructural unit of Serbia

Directory of Open Access Journals (Sweden)

Ćalić Jelena

2012-01-01

Full Text Available Differentiation between the terms “Pannonian Basin” and “Pannonian Plain” is not clear enough in geographical literature. The paper discusses the usage of the term “plain” in geomorphology, as well as the usage of a quantitative method for plain delineation, through calculation of relief roughness coefficient (using a digital elevation model. Qualitative analysis, which includes the definition of dominant geomorphological processes and the distribution of Quaternary sediments, is an addition to the quantitative analysis. In the Republic of Serbia, the area of the Pannonian plain defined in this way is 24,448 km2, which is 27.5% of the total territory of the country. The paper gives the overview of the geotectonic structure and evolution of the Pannonian Basin System, with special stress on the territory of Serbia, as well as the chronology of the Pannonian sedimentation area in Serbia from the Lower Miocene till present. In order to explain the status of the Pannonian plain as one of the morphostructural units of Serbia, the theoretical basics of morphostructures are discussed, as well as the principles of their spatial definition and the relation to the notion of a geological structure. [Projekat Ministarstva nauke Republike Srbije, br. 47007

Performance evaluation of annular arrays in practice: The measurement of phase and amplitude patterns of radio-frequency deep body applicators

NARCIS (Netherlands)

Schneider, C.J.; Kuijer, J.P.A.; Colussi, L.C.; Schepp, C.J.; Dijk, J.D.P. van

1995-01-01

An approach to a solution of two major problems in operating Annular Phased Arrays in deep body hyperthermia is presented: an E-field sensor capable of measuring phase and amplitude at 70 MHz and the concept of a power transmission factor to determine the effective amplitude of each applicator. In

Worst-case-efficient dynamic arrays in practice

DEFF Research Database (Denmark)

Katajainen, Jyrki

2016-01-01

The basic operations of a dynamic array are operator[], push back, and pop back. This study is an examination of variations of dynamic arrays that support these operations at O(1) worst-case cost. In the literature, many solutions have been proposed, but little information is available on their m......The basic operations of a dynamic array are operator[], push back, and pop back. This study is an examination of variations of dynamic arrays that support these operations at O(1) worst-case cost. In the literature, many solutions have been proposed, but little information is available...... on their mutual superiority. Most library implementations only guarantee O(1) amortized cost per operation. Four variations with good worst-case performance were benchmarked: (1) resizable array relying on doubling, halving, and incremental copying; (2) level-wiseallocated pile; (3) sliced array with fixed......-capacity slices; and (4) blockwise-allocated pile. Let |V| denote the size of the values of type V and |V*| the size of the pointers to values of type V, both measured in bytes. For an array of n values and a slice of S values, the space requirements of the considered variations were at most 12|V|n+O(|V*|), 2|V...

Very high frequency (beyond 100 MHz) PZT kerfless linear arrays.

Science.gov (United States)

Wu, Da-Wei; Zhou, Qifa; Geng, Xuecang; Liu, Chang-Geng; Djuth, Frank; Shung, K Kirk

2009-10-01

This paper presents the design, fabrication, and measurements of very high frequency kerfless linear arrays prepared from PZT film and PZT bulk material. A 12-microm PZT thick film fabricated from PZT-5H powder/solution composite and a piece of 15-microm PZT-5H sheet were used to fabricate 32-element kerfless high-frequency linear arrays with photolithography. The PZT thick film was prepared by spin-coating of PZT sol-gel composite solution. The thin PZT-5H sheet sample was prepared by lapping a PZT-5H ceramic with a precision lapping machine. The measured results of the 2 arrays were compared. The PZT film array had a center frequency of 120 MHz, a bandwidth of 60% with a parylene matching layer, and an insertion loss of 41 dB. The PZT ceramic sheet array was found to have a center frequency of 128 MHz with a poorer bandwidth (40% with a parylene matching layer) but a better sensitivity (28 dB insertion loss).

Coded aperture subreflector array for high resolution radar imaging

Science.gov (United States)

Lynch, Jonathan J.; Herrault, Florian; Kona, Keerti; Virbila, Gabriel; McGuire, Chuck; Wetzel, Mike; Fung, Helen; Prophet, Eric

2017-05-01

HRL Laboratories has been developing a new approach for high resolution radar imaging on stationary platforms. High angular resolution is achieved by operating at 235 GHz and using a scalable tile phased array architecture that has the potential to realize thousands of elements at an affordable cost. HRL utilizes aperture coding techniques to minimize the size and complexity of the RF electronics needed for beamforming, and wafer level fabrication and integration allow tiles containing 1024 elements to be manufactured with reasonable costs. This paper describes the results of an initial feasibility study for HRL's Coded Aperture Subreflector Array (CASA) approach for a 1024 element micromachined antenna array with integrated single-bit phase shifters. Two candidate electronic device technologies were evaluated over the 170 - 260 GHz range, GaN HEMT transistors and GaAs Schottky diodes. Array structures utilizing silicon micromachining and die bonding were evaluated for etch and alignment accuracy. Finally, the overall array efficiency was estimated to be about 37% (not including spillover losses) using full wave array simulations and measured device performance, which is a reasonable value at 235 GHz. Based on the measured data we selected GaN HEMT devices operated passively with 0V drain bias due to their extremely low DC power dissipation.

Summary of the Snake River plain Regional Aquifer-System Analysis in Idaho and eastern Oregon

Science.gov (United States)

Lindholm, G.F.

1996-01-01

500 feet of alluvium ranges from about 4 to 40 feet per day; higher values can be expected in individual sand and gravel zones. Vertical hydraulic conductivity is considerably lower because of the presence of clay layers. Hydraulic heads measured in piezometers, interpreted from diagrams showing ground-water flow and equipotential lines and estimated by computer simulation, demonstrate that water movement is three dimensional through the rock framework. Natural recharge takes place along the margins of the plain where head decreases with depth; discharge takes place near some reaches of the Snake River and the Boise River where head increases with depth. Geothermal water in rhyolitic rocks in the western plain and western part of the eastern plain has higher hydraulic head than the overlying cold water. Geothermal water, therefore, moves upward and merges into the cold-water system. Basin water-budget analyses indicate that the volume of cold water. Carbon-14 age determinations, which indicate that residence time of geothermal water is 17,700 to 20,300 years, plus or minus 4,000 years, imply slow movement of water through the geothermal system. Along much of its length, the Snake River gains large quantities of ground water. On the eastern plain, the river gained about 1.9 million acre-feet of water between Blackfoot and Neeley, Idaho, in 1980. Between Milner and King Hill, Idaho, the river gained 4.7 million acre-feet, mostly as spring flow from the north side. Upstream from Blackfoot and in the vicinity of Lake Walcott, the rover loses flow to ground water during parts or all of the year. On the western plain, river gains from ground water are small relative to those on the eastern plain; most are from seepage. Streams in tributary drainage basins supply calcium/bicarbonate type and calcium/magnesium/bicarbonate type water to the plain. Water type is a reflection of the chemical composition of rocks in the drainage basin, Concentrations of dissolved solids are

Exploration for petroleum and natural gas in Sonai Plain

Energy Technology Data Exchange (ETDEWEB)

Konishi, K

1965-09-01

Exploration in the Sonai Plain by Sekyu Shigen Kaihatsu Kabushiki Kaisha (Oil Resources Development Corporation) since 1955 is described. The development tasks are made difficult due to the presence of permeability traps. However, 41 out of 65 wells drilled up to late March of 1965 have been successful. Quantities of crude oil and natural gas produced in 1963 were, respectively, 5 and 6 times those of 1958. The Sonai Plain is a relatively new area, and there are still many unknown factors, yet the rate of development has increased greatly. More and deeper wells are expected to be drilled with even better results.

17 CFR 240.15d-20 - Plain English presentation of specified information.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Plain English presentation of specified information. 240.15d-20 Section 240.15d-20 Commodity and Securities Exchanges SECURITIES AND... Regulations Under the Securities Exchange Act of 1934 Other Reports § 240.15d-20 Plain English presentation of...

17 CFR 240.13a-20 - Plain English presentation of specified information.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Plain English presentation of specified information. 240.13a-20 Section 240.13a-20 Commodity and Securities Exchanges SECURITIES AND... Regulations Under the Securities Exchange Act of 1934 Other Reports § 240.13a-20 Plain English presentation of...

Cardiac Arrest Following Spinal Anaesthesia With Plain ...

African Journals Online (AJOL)

year old woman who was admitted for an elective caesarean section. After preoperative evaluation and premedication she received a spinal anaesthesia in the L3-4 interspace with plain bupivacaine 0.5%. After being replaced in the supine ...

Lithosphere stress changes due to groundwater unloading in North China Plain

Science.gov (United States)

Pang, Yajin; Zhang, Huai; Shi, Yaolin

2015-04-01

During the past 50 years, excessive groundwater pumping has led to the continuous decline of groundwater table in North China Plain, which becomes one of the global hotspots of groundwater depletion. Over most of the rural areas of the plain, the shallow aquifer has experienced a water-table decline of more than 15m, with greater declines up to 50m in most urban centres, such as Beijing, Tangshan, Shijiangzhuang and so forth in 1960-2000. The entire groundwater depletion area covers a total area of approximately 56,273 km2 , more than 40% of the North China Plain. The vast area of enormous groundwater exploitation in North China Plain will definitely unload the lithosphere and create stress perturbations, the problem is if the stresses change large enough to affect tectonic activities. In this essay, we set up a 3 dimensional numerical visco-elastic model to discuss the effect of groundwater over-pumping on the lithosphere deformation and stress state in North China Plain. Based on the records of total groundwater-table decline during 1960-2010 in North China Plain, we estimate the accumulated deformation and lithosphere stress due to unloading of human-induced groundwater depletion. The area in the model ranges from 34° To 42°N, and 112° To 119°E, including the major groundwater depression cones in North China Plain. According to the simulating result, the maximum surface vertical uplift caused by groundwater unloading is 8cm. Meanwhile cumulative horizontal crustal stress changes near the surface goes up to 100kPa, and up to 40kPa at 15km depth where most earthquakes occurred in this area. The tectonic compressive stress rate is about 0.25kPa per year. Therefore, the stress changes due to groundwater pumping is significant compared with the tectonic driven stress changes. As China developed rapidly since 1978, the groundwater table mainly declined after 1978. Taking the earthquake catalog in the vicinity of groundwater depression zone into consideration, we

Yellowstone-Snake River Plain seismic profilling experiment: Crustal structure of the eastern Snake River Plain

International Nuclear Information System (INIS)

Braile, L.W.; Smith, R.B.; Ansorge, J.; Baker, M.R.; Sparlin, M.A.; Prodehl, C.; Schilly, M.M.; Healy, J.H.; Mueller, S.; Olsen, K.H.

1982-01-01

Seismic refraction profiles recorded along the eastern Snake River Plain (ESRP) in southeastern Idaho during the 1978 Yellowstone-Snake River Plain cooperative seismic profiling experiment are interpreted to infer the crustal velocity and attenuation (Q-1) structure of the ESRP. Travel-time and synthetic seismogram modeling of a 250 km reversed refraction profile as well as a 100 km detailed profile indicate that the crust of the ESRP is highly anomalous. Approximately 3 to 6 km of volcanic rocks (with some interbedded sediments) overlie an upper-crustal layer (compressional velocity approx. =6.1 km/s) which thins southwestward along the ESRP from a thickness of 10 km near Island Park Caldera to 2 to 3 km beneath the central and southwestern portions of the ESRP. An intermediate-velocity (approx. =6.5 km/s) layer extends from approx. =10 to approx. =20 km depth. a thick (approx. =22 km) lower crust of compressional velocity 6.8 km/s, a total crustall thickness of approx. =42 km, and a P/sub n/ velocity of approx. =7.9 km/s is observed in the ESRP, similar to the western Snake River Plain and the Rocky Mountains Provinces. High attenuation is evident on the amplitude corrected seismic data due to low-Q values in the volcanic rocks (Q/sub p/ = 20 to 200) and throughout the crust (Q/sub p/ = 160 to 300). Based on these characteristics of the crustal structure and volcanic-age progression data, it is suggested that the ESRP has resulted from an intensitive period of intrusion of mantle-derived basaltic magma into the upper crust generating explosive silicic volcanism and associated regional uplift and caldera collapse. This activity began about 15 m.y. ago in southwestern Idaho and has migrated northeast to its present position at Yellowstone. Subsequent cooling of the intruded upper crust results in the 6.5 km/s velocity intermediate layer. Crustal subsidence and periodic basaltic volcanism as represented by the ESRP complete the sequence of crustal evolution

A dual-band planar array of connected dipoles: Experimental validation based on bistatic RCS measurements

NARCIS (Netherlands)

Cavallo, D.; Neto, A.; Gerini, G.; Morello, D.

2010-01-01

Rigorous equivalent networks representing connected arrays in transmission and reception are derived in this paper. These equivalent networks are not based on reciprocity but on Green's functions. Thus, all components have well identified and physically meaningful roles. A dual-band connected array

Study of nuclei far from stability with AYE-Ball array

International Nuclear Information System (INIS)

Carpenter, M.P.

1996-01-01

The coupling of a Compton-suppressed Ge (CsGe) detector array to a recoil mass separator (RMS) has seen limited use in the past due to the low efficiency for measuring recoil-γ ray coincidences (< 0.1%). With the building of new generation recoil separators and gamma-ray arrays, a substantial increase in detection efficiency has been achieved. This allows for the opportunity to measure excited states in nuclei with cross-sections approaching 100 nb. In this paper, results from the coupling of a modest array of CsGe detectors (AYE-Ball) with a recoil separator (FMA) will be presented

Reverse Phase Protein Arrays for High-Throughput Protein Measurements in Mammospheres

DEFF Research Database (Denmark)

Pedersen, Marlene Lemvig; Block, Ines; List, Markus

Protein Array (RPPA)-based readout format integrated into robotic siRNA screening. This technique would allow post-screening high-throughput quantification of protein changes. Recently, breast cancer stem cells (BCSCs) have attracted much attention, as a tumor- and metastasis-driving subpopulation...

Application of high resolution SNP arrays in patients with congenital ...

Indian Academy of Sciences (India)

TING-YING LEI

lent oligonucleotide-based array-CGH to determine the exact breakpoints in 14 patients with partial deletions of chromo- some 13q21.1-qter. They were able to refine the smallest deletion region linked to cleft lip/palate (13q31.3–13q33.1). Except for the arrays that measure DNA copy number differ- ences only, SNP arrays, ...

The value of plain abdominal radiographs in management of abdominal emergencies in Luth.

Science.gov (United States)

Ashindoitiang, J A; Atoyebi, A O; Arogundade, R A

2008-01-01

The plain abdominal x-ray is still the first imaging modality in diagnosis of acute abdomen. The aim of this study was to find the value of plain abdominal x-ray in the management of abdominal emergencies seen in Lagos university teaching hospital. The accurate diagnosis of the cause of acute abdominal pain is one of the most challenging undertakings in emergency medicine. This is due to overlapping of clinical presentation and non-specific findings of physical and even laboratory data of the multifarious causes. Plain abdominal radiography is one investigation that can be obtained readily and within a short period of time to help the physician arrive at a correct diagnosis The relevance of plain abdominal radiography was therefore evaluated in the management of abdominal emergencies seen in Lagos over a 12 month period (April 2002 to March 2003). A prospective study of 100 consecutively presenting patients with acute abdominal conditions treated by the general surgical unit of Lagos University Teaching Hospital was undertaken. All patients had supine and erect abdominal x-ray before any therapeutic intervention was undertaken. The diagnostic features of the plain films were compared with final diagnosis to determine the usefulness of the plain x-ray There were 54 males and 46 females (M:F 1.2:1). Twenty-four percent of the patients had intestinal obstruction, 20% perforated typhoid enteritis; gunshot injuries and generalized peritonitis each occurred in 13%, blunt abdominal trauma in 12%, while 8% and 10% had acute appendicitis and perforated peptic ulcer disease respectively. Of 100 patients studied, 54% had plain abdominal radiographs that showed positive diagnostic features. Plain abdominal radiograph showed high sensitivity in patients with intestinal obstruction 100% and perforated peptic ulcer 90% but was less sensitive in patients with perforated typhoid, acute appendicitis, and blunt abdominal trauma and generalized peritonitis. In conclusion, this study

Application of Three Electrical Resistivity Arrays to Evaluate ...

African Journals Online (AJOL)

The study further revealed that the Wenner array is less susceptible to edge effect at shallow depth while Dipole-dipole is more susceptible to edge effect at deeper depth followed by the Pole-dipole array. 2D electrical resistivity field measurements were carried out to confirm the results of the numerical simulation in the ...

Real Time Photovoltaic Array Simulator for Testing Grid-Connected PV Inverters

DEFF Research Database (Denmark)

Sera, Dezso; Valentini, Massimo; Raducu, Alin

2008-01-01

In this paper a real time flexible PV array simulator is presented. It is a system that can simulate different PV panel arrays in specific environmental conditions. To evaluate performance of the Maximum Power Point Tracking (MPPT) of grid-connected Photovoltaic (PV) inverters only measurements...... undertaken with an appropriate PV array simulator provide accurate and reproducible results. Thus the PV array simulator has been developed and implemented. MPPT efficiency tests on a commercial grid-connected PV inverter have been performed to validate the PV array simulator....

THE EFFECT OF A CULTURALLY TAILORED SUBSTANCE ABUSE PREVENTION INTERVENTION WITH PLAINS INDIAN ADOLESCENTS.

Science.gov (United States)

Patchell, Beverly A; Robbins, Leslie K; Lowe, John A; Hoke, Mary M

2015-01-01

To examine the effects of incorporating tribal specific cultural beliefs into a tailored substance abuse prevention intervention for at risk rural Oklahoma Native American Indian (NAI) Plains adolescents. The 10 hour Native American Talking Circle Intervention, a school-based, group substance abuse prevention program, was implemented over a 8.5 week period and evaluated using a one group, pretest-posttest design. Measurements were from the Native Self-Reliance Questionnaire and the Substance Problems Scale from Global Appraisal of Individual Needs-Quick (GAIN-Q). One-tailed, paired sample t-tests demonstrated significant increase in self-reliance, from 86.227 to 92.204 (t (43) = -2.580, p = .007) and a decrease in substance abuse/use, from 2.265 to 1.265 (t (33) = 1.844, p = .007). The Native Talking Circle Intervention based on tribal-specific values and beliefs was shown to be effective with substance abuse/use at-risk NAI Plains tribal adolescents.

Level III Ecoregions of the Mississippi Alluvial Plain

Data.gov (United States)

U.S. Environmental Protection Agency — Ecoregions for the Mississippi Alluvial Plain were extracted from the seamless national shapefile. Ecoregions denote areas of general similarity in ecosystems and in...

Level IV Ecoregions of the Mississippi Alluvial Plain

Data.gov (United States)

U.S. Environmental Protection Agency — Ecoregions for the Mississippi Alluvial Plain were extracted from the seamless national shapefile. Ecoregions denote areas of general similarity in ecosystems and in...

SNP Arrays

Directory of Open Access Journals (Sweden)

Jari Louhelainen

2016-10-01

Full Text Available The papers published in this Special Issue “SNP arrays” (Single Nucleotide Polymorphism Arrays focus on several perspectives associated with arrays of this type. The range of papers vary from a case report to reviews, thereby targeting wider audiences working in this field. The research focus of SNP arrays is often human cancers but this Issue expands that focus to include areas such as rare conditions, animal breeding and bioinformatics tools. Given the limited scope, the spectrum of papers is nothing short of remarkable and even from a technical point of view these papers will contribute to the field at a general level. Three of the papers published in this Special Issue focus on the use of various SNP array approaches in the analysis of three different cancer types. Two of the papers concentrate on two very different rare conditions, applying the SNP arrays slightly differently. Finally, two other papers evaluate the use of the SNP arrays in the context of genetic analysis of livestock. The findings reported in these papers help to close gaps in the current literature and also to give guidelines for future applications of SNP arrays.

Landscape-scale patterns of fire and drought on the high plains, USA

Science.gov (United States)

Paulette Ford; Charles Jackson; Matthew Reeves; Benjamin Bird; Dave Turner

2015-01-01

We examine 31 years (1982-2012) of temperature, precipitation and natural wildfire occurrence data for Federal and Tribal lands to determine landscape-scale patterns of drought and fire on the southern and central High Plains of the western United States. The High Plains states of Colorado, Kansas, Nebraska, New Mexico, Oklahoma, South Dakota, Texas and...

A comparison of some methods to estimate the fatigue life of plain dents

Energy Technology Data Exchange (ETDEWEB)

Martins, Ricardo R.; Noronha Junior, Dauro B. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2009-12-19

This paper describes a method under development at PETROBRAS R and D Center (CENPES) to estimate the fatigue life of plain dents. This method uses the API Publication 1156 as a base to estimate the fatigue life of dome shaped plain dents and the Pipeline Defect Assessment Manual (PDAM) approach to take into account the uncertainty inherent in the fatigue phenomenon. CENPES method, an empirical and a semi-empirical method available in the literature were employed to estimate the fatigue lives of 10 plain dents specimens of Year 1 of an ongoing test program carried out by BMT Fleet Technology Limited, with the support of the Pipeline Research Council International (PRCI). The results obtained with the different methods are presented and compared. Furthermore some details are given on the numerical methodology proposed by PETROBRAS that have been used to describe the behavior of plain dents. (author)

Resonance modes in one-dimensional parallel arrays of Josephson junctions

International Nuclear Information System (INIS)

Van der Zant, H.S.J.; Delin, K.A.; Bock, R.D.; Berman, D.; Phillips, J.R.; Orlando, T.P.

1994-01-01

We investigate both experimentally and numerically the dynamics of discrete one-dimensional parallel arrays of underdamped Josephson junctions. In a magnetic field, measurements show steps in the current-voltage characteristics which are the discrete analogs of Fiske steps in a long Josephson junction. From the position of the steps, one can construct a plot of the dispersion relation ω(k). We observe a sine--dependence in the dispersion relation due to the discrete nature of our arrays. We also observe an additional, smaller gap at a k-value determined by the periodicity of the vortex lattice. Our measurements are supported by numerical simulations of the full dynamics. The Fiske steps provide an experimental method to measure the self-inductance of 1D parallel arrays. (orig.)

Comparison of intrathecal plain articaine and levobupivacaine with fentanyl for Caesarean section.

Science.gov (United States)

Demircioglu, Rüveyda I; Gozdemir, Muhammet; Usta, Burhanettin; Sert, Hüseyin; Karabayirli, Safinaz; Muslu, Bünyamin; Keskin, Esra A

2016-12-01

Articaine is used as a local anesthetic for outpatient surgery because it offers rapid onset of anesthesia and short duration motor block. Levobupivacaine is often preferred for Caesarean section. We evaluated the anesthetic characteristics of fentanyl-supplemented plain articaine and levobupivacaine for Caesarean section under combine spinal epidural anesthesia. Patients undergoing Caesarean section received in random order plain articaine 40 mg (Group A, n=50) or plain levobupivacaine 10 mg (Group L, n=50) mixed with fentanyl 20 µg intrathecally. The onset and duration of sensory and motor block, first analgesic request, and hemodynamic parameters were recorded. Onset times of maximum motor block were longer in Group L than Group A (P=0,001). Time to two-segment regression of sensory block were 70 min for Group A and 90 min group L (P=0.001). Times to complete regression of motor blockade were significantly longer in group L than group A (P =0,001). To have a faster onset and shorter duration of spinal anesthesia, we recommend the use of plain articaine for Caesarean section.

Diagnosis of cancer of the tongue and oral floor using plain CT

International Nuclear Information System (INIS)

Ariji, Eiichiro; Kanda, Shigenobu

1988-01-01

CT images of 18 patients, diagnosed squamous cell carcinomas of the tongue or oral floor, were analyzed to assess the clinical importance of plain CT for primary sites. All cases were scanned on Somatom DR (Siemens) at the Department of Dental Radiology, Kyushu University Dental Hospital from 1985 to 1988. Results were as follows : 1, As descriptions of primary tumors mainly depended on their size in soft tissue, plain CT was useful only for advanced cases (T3, T4). 2, For cancer of the oral floor and advanced cases of cancer of the tongue, plain CT was useful to evaluate the bone invasion, especially in cases of lingual cortex of the anterior mandible. (author)

A novel method to design sparse linear arrays for ultrasonic phased array.

Science.gov (United States)

Yang, Ping; Chen, Bin; Shi, Ke-Ren

2006-12-22

In ultrasonic phased array testing, a sparse array can increase the resolution by enlarging the aperture without adding system complexity. Designing a sparse array involves choosing the best or a better configuration from a large number of candidate arrays. We firstly designed sparse arrays by using a genetic algorithm, but found that the arrays have poor performance and poor consistency. So, a method based on the Minimum Redundancy Linear Array was then adopted. Some elements are determined by the minimum-redundancy array firstly in order to ensure spatial resolution and then a genetic algorithm is used to optimize the remaining elements. Sparse arrays designed by this method have much better performance and consistency compared to the arrays designed only by a genetic algorithm. Both simulation and experiment confirm the effectiveness.

International collaborative study for the calibration of proposed International Standards for thromboplastin, rabbit, plain, and for thromboplastin, recombinant, human, plain.

Science.gov (United States)

van den Besselaar, A M H P; Chantarangkul, V; Angeloni, F; Binder, N B; Byrne, M; Dauer, R; Gudmundsdottir, B R; Jespersen, J; Kitchen, S; Legnani, C; Lindahl, T L; Manning, R A; Martinuzzo, M; Panes, O; Pengo, V; Riddell, A; Subramanian, S; Szederjesi, A; Tantanate, C; Herbel, P; Tripodi, A

2018-01-01

Essentials Two candidate International Standards for thromboplastin (coded RBT/16 and rTF/16) are proposed. International Sensitivity Index (ISI) of proposed standards was assessed in a 20-centre study. The mean ISI for RBT/16 was 1.21 with a between-centre coefficient of variation of 4.6%. The mean ISI for rTF/16 was 1.11 with a between-centre coefficient of variation of 5.7%. Background The availability of International Standards for thromboplastin is essential for the calibration of routine reagents and hence the calculation of the International Normalized Ratio (INR). Stocks of the current Fourth International Standards are running low. Candidate replacement materials have been prepared. This article describes the calibration of the proposed Fifth International Standards for thromboplastin, rabbit, plain (coded RBT/16) and for thromboplastin, recombinant, human, plain (coded rTF/16). Methods An international collaborative study was carried out for the assignment of International Sensitivity Indexes (ISIs) to the candidate materials, according to the World Health Organization (WHO) guidelines for thromboplastins and plasma used to control oral anticoagulant therapy with vitamin K antagonists. Results Results were obtained from 20 laboratories. In several cases, deviations from the ISI calibration model were observed, but the average INR deviation attributabled to the model was not greater than 10%. Only valid ISI assessments were used to calculate the mean ISI for each candidate. The mean ISI for RBT/16 was 1.21 (between-laboratory coefficient of variation [CV]: 4.6%), and the mean ISI for rTF/16 was 1.11 (between-laboratory CV: 5.7%). Conclusions The between-laboratory variation of the ISI for candidate material RBT/16 was similar to that of the Fourth International Standard (RBT/05), and the between-laboratory variation of the ISI for candidate material rTF/16 was slightly higher than that of the Fourth International Standard (rTF/09). The candidate materials

My Website Reads at an Eighth Grade Level: Why Plain Language Benefits Your Users (and You)

Science.gov (United States)

Skaggs, Danielle

2017-01-01

Writing in plain language aims to help users find what they need and ensures that the information is both useful and understandable. This is key for distance students whose primary library interaction may be with the library Website. A mix of user research and readability scores can be used to measure whether content is findable, useful, and…

Vegetation - Carrizo Plain ER, 2005 - 2008 [ds561

Data.gov (United States)

California Natural Resource Agency — The Vegetation Map of the Carrizo Plain Ecological Reserve, San Luis Obispo County, California was created by the California Department of Fish and Game (DFG)...

Hyperdensity liver tumor on plain CT

Energy Technology Data Exchange (ETDEWEB)

Hirota, Shozo; Hanaguri, Katsuro [Kochi Municipal Central Hospital (Japan); Shimizu, Masahumi; Sako, Masao; Harada, Yasushi

1984-12-01

Most liver tumors on plain CT have been recognized as low density or iso-density masses. Sometimes calcified high density masses were shown on plain CT in case of cysts or metastatic liver tumors. However, hyperdensity mass of the liver on CT, of which the density was a little higher than surrounding tissues, was very rare. Recently 7 patients with hyperdensity liver masses on plain CT were experienced: 6 hepatocellular carcinomas and 1 hepatic cavernous hemangioma. A single hyperdensity mass was shown in 4 patients, a hyperdensity mass of multiple hepatic tumors was shown in 2 patients, and some hyperdensity masses of multiple hepatic tumors were shown in 1 patient. Lesions are classified in 3 types according to the appearance of hyperdensity masses: diffuse hyperdensity all over the mass, ring like hyperdensity, creascent like hyperdensity. Intravenous contrast enhancement was performed in 2 patients: one with a primary hepatocellular carcinoma, and another with a hepatic cavernous hemangioma. In the former case the tumor margin had changed unclear, in the latter case the tumor was markedly enhanced. Our results revealed that hyperdensity liver tumors were divided into 2 types: One type, shown in a cavernous hemangioma with fatty liver, demonstrated relative hyperdensity due to lower density of the surrounding tissue. Another type, shown in 6 hepatocellular carcinomas, showed hyperdensity since the density of the tumor was hyperdensity relative to the surrounding tissue of the liver. It was suggested that the tumor with the latter type had been strongly probable of malignant one, and been recommended to receive further examination. Cause of hyperdensity was thought to be due to hemorrhage, though microcalcification could not be denyed. In Japan, no hyperdensity liver tumor had been reported partly due to a wide window width with which CT photographs were taken.

A Fast Method for Measuring Psychophysical Thresholds Across the Cochlear Implant Array

Directory of Open Access Journals (Sweden)

Julie A. Bierer

2015-02-01

Full Text Available A rapid threshold measurement procedure, based on Bekesy tracking, is proposed and evaluated for use with cochlear implants (CIs. Fifteen postlingually deafened adult CI users participated. Absolute thresholds for 200-ms trains of biphasic pulses were measured using the new tracking procedure and were compared with thresholds obtained with a traditional forced-choice adaptive procedure under both monopolar and quadrupolar stimulation. Virtual spectral sweeps across the electrode array were implemented in the tracking procedure via current steering, which divides the current between two adjacent electrodes and varies the proportion of current directed to each electrode. Overall, no systematic differences were found between threshold estimates with the new channel sweep procedure and estimates using the adaptive forced-choice procedure. Test–retest reliability for the thresholds from the sweep procedure was somewhat poorer than for thresholds from the forced-choice procedure. However, the new method was about 4 times faster for the same number of repetitions. Overall the reliability and speed of the new tracking procedure provides it with the potential to estimate thresholds in a clinical setting. Rapid methods for estimating thresholds could be of particular clinical importance in combination with focused stimulation techniques that result in larger threshold variations between electrodes.

Smith-Purcell experiment utilizing a field-emitter array cathode: measurements of radiation

International Nuclear Information System (INIS)

Ishizuka, H.; Kawamura, Y.; Yokoo, K.; Shimawaki, H.; Hosono, A.

2001-01-01

Smith-Purcell (SP) radiation at wavelengths of 350-750 nm was produced in a tabletop experiment using a field-emitter array (FEA) cathode. The electron gun was 5 cm long, and a 25 mmx25 mm holographic replica grating was placed behind the slit provided in the anode. A regulated DC power supply accelerated electron beams in excess of 10 μA up to 45 keV, while a small Van de Graaff generator accelerated smaller currents to higher energies. The grating had a 0.556 μm period, 30 deg. blaze and a 0.2 μm thick aluminum coating. Spectral characteristics of the radiation were measured both manually and automatically; in the latter case, the spectrometer was driven by a stepping motor to scan the wavelength, and AD-converted signals from a photomultiplier tube were processed by a personal computer. The measurement, made at 80 deg. relative to the electron beam, showed good agreement with theoretical wavelengths of the SP radiation. Diffraction orders were -2 and -3 for beam energies higher than 45 keV, -3 to -5 at 15-25 keV, and -2 to -4 in between. The experiment has thus provided evidence for the practical applicability of FEAs to compact radiation sources

First light from a kilometer-baseline Scintillation Auroral GPS Array.

Science.gov (United States)

Datta-Barua, S; Su, Y; Deshpande, K; Miladinovich, D; Bust, G S; Hampton, D; Crowley, G

2015-05-28

We introduce and analyze the first data from an array of closely spaced Global Positioning System (GPS) scintillation receivers established in the auroral zone in late 2013 to measure spatial and temporal variations in L band signals at 100-1000 m and subsecond scales. The seven receivers of the Scintillation Auroral GPS Array (SAGA) are sited at Poker Flat Research Range, Alaska. The receivers produce 100 s scintillation indices and 100 Hz carrier phase and raw in-phase and quadrature-phase samples. SAGA is the largest existing array with baseline lengths of the ionospheric diffractive Fresnel scale at L band. With an initial array of five receivers, we identify a period of simultaneous amplitude and phase scintillation. We compare SAGA power and phase data with collocated 630.0 nm all-sky images of an auroral arc and incoherent scatter radar electron precipitation measurements, to illustrate how SAGA can be used in multi-instrument observations for subkilometer-scale studies. A seven-receiver Scintillation Auroral GPS Array (SAGA) is now at Poker Flat, Alaska SAGA is the largest subkilometer array to enable phase/irregularities studies Simultaneous scintillation, auroral arc, and electron precipitation are observed.

Measuring Millimeter Wave of Cold Atmospheric Plasma Array by a Novel Technique

Directory of Open Access Journals (Sweden)

Bryon Eckert

2016-08-01

Full Text Available An unexplained repulsive force occasionally observed during non-thermal plasma treatment of large infections may point the way to an efficient mechanism for characterizing biofield energy. Ambient pressure air plasma in non-thermal equilibrium creates areas of localized population inversion, causing spontaneous emission at magnetic dipole rotational resonance lines. For O2, many of these lines occur in the 60 GHz frequency range. This experiment examines a possible link between the fine resonance frequencies of oxygen in the 60 GHz region, and the therapeutic frequencies used in Russian non-thermal EHF therapy. This paper also explores the feasibility of using a plasma array for biological torsion field characterization. An array of several hundred non-thermal plasma plumes are placed directly in front of a circular horn. A switchable circular polarizer is used to select left hand circular, linear or right hand circular polarization. A low noise frequency converter allows a noise temperature of less than 1150 K. A frequency scan and averaging algorithm is developed to characterize noise temperature versus frequency, comparing signal and noise levels between plasma on and plasma off, and switching polarization sense. An experimental setup is proposed as a proof of concept for detecting signals from the plasma array, while a practical laboratory tool is also proposed.

Quantifying uncertainties of seismic Bayesian inversion of Northern Great Plains

Science.gov (United States)

Gao, C.; Lekic, V.

2017-12-01

Elastic waves excited by earthquakes are the fundamental observations of the seismological studies. Seismologists measure information such as travel time, amplitude, and polarization to infer the properties of earthquake source, seismic wave propagation, and subsurface structure. Across numerous applications, seismic imaging has been able to take advantage of complimentary seismic observables to constrain profiles and lateral variations of Earth's elastic properties. Moreover, seismic imaging plays a unique role in multidisciplinary studies of geoscience by providing direct constraints on the unreachable interior of the Earth. Accurate quantification of uncertainties of inferences made from seismic observations is of paramount importance for interpreting seismic images and testing geological hypotheses. However, such quantification remains challenging and subjective due to the non-linearity and non-uniqueness of geophysical inverse problem. In this project, we apply a reverse jump Markov chain Monte Carlo (rjMcMC) algorithm for a transdimensional Bayesian inversion of continental lithosphere structure. Such inversion allows us to quantify the uncertainties of inversion results by inverting for an ensemble solution. It also yields an adaptive parameterization that enables simultaneous inversion of different elastic properties without imposing strong prior information on the relationship between them. We present retrieved profiles of shear velocity (Vs) and radial anisotropy in Northern Great Plains using measurements from USArray stations. We use both seismic surface wave dispersion and receiver function data due to their complementary constraints of lithosphere structure. Furthermore, we analyze the uncertainties of both individual and joint inversion of those two data types to quantify the benefit of doing joint inversion. As an application, we infer the variation of Moho depths and crustal layering across the northern Great Plains.

MEMS-Based Solid Propellant Rocket Array Thruster

Science.gov (United States)

Tanaka, Shuji; Hosokawa, Ryuichiro; Tokudome, Shin-Ichiro; Hori, Keiichi; Saito, Hirobumi; Watanabe, Masashi; Esashi, Masayoshi

The prototype of a solid propellant rocket array thruster for simple attitude control of a 10 kg class micro-spacecraft was completed and tested. The prototype has 10×10 φ0.8 mm solid propellant micro-rockets arrayed at a pitch of 1.2 mm on a 20×22 mm substrate. To realize such a dense array of micro-rockets, each ignition heater is powered from the backside of the thruster through an electrical feedthrough which passes along a propellant cylinder wall. Boron/potassium nitrate propellant (NAB) is used with/without lead rhodanide/potassium chlorate/nitrocellulose ignition aid (RK). Impulse thrust was measured by a pendulum method in air. Ignition required electric power of at least 3 4 W with RK and 4 6 W without RK. Measured impulse thrusts were from 2×10-5 Ns to 3×10-4 Ns after the calculation of compensation for air dumping.

Free air on plain film: Do we need a computed tomography too?

Directory of Open Access Journals (Sweden)

Carolina V Solis

2014-01-01

Full Text Available Context: Standard teaching is that patients with pneumoperitoneum on plain X-ray and clinical signs of abdominal pathology should undergo urgent surgery. It is unknown if abdominal computed tomography (CT provides additional useful information in this scenario. Aims: The aim of this study is to determine whether or not CT scanning after identification of pneumoperitoneum on plain X-ray changes clinical management or outcomes. Settings and Design: Retrospective study carried out over 4 years at a tertiary care academic medical center. All patients in our acute care surgery database with pneumoperitoneum on plain X-ray were included. Patients who underwent subsequent CT scanning (CT group were compared with patients who did not (non-CT group. Statistical Analysis Used: The Wilcoxon rank-sum test, t-test and Fisher′s exact test were used as appropriate to compare the groups. Results: There were 25 patients in the non-CT group and 18 patients in the CT group. There were no differences between the groups at presentation. All patients in the non-CT group underwent surgery, compared with 83% (n = 15 of patients in the CT group (P = 0.066. 16 patients in the non-CT and 11 patients in the CT group presented with peritonitis and all underwent surgery regardless of group. For patients undergoing surgery, there were no differences in outcomes between the groups. After X-ray, patients undergoing CT required 328.0 min to arrive in the operating room compared with 136.0 min in the non-CT group (P = 0.007. Conclusions: In patients with pneumoperitoneum on X-ray and peritonitis on physical exam, CT delays surgery without providing any measurable benefit.

Geothermal alteration of basaltic core from the Snake River Plain, Idaho

Science.gov (United States)

Sant, Christopher J.

The Snake River Plain is located in the southern part of the state of Idaho. The eastern plain, on which this study focuses, is a trail of volcanics from the Yellowstone hotspot. Three exploratory geothermal wells were drilled on the Snake River Plain. This project analyzes basaltic core from the first well at Kimama, north of Burley, Idaho. The objectives of this project are to establish zones of geothermal alteration and analyze the potential for geothermal power production using sub-aquifer resources on the axial volcanic zone of the Snake River Plain. Thirty samples from 1,912 m of core were sampled and analyzed for clay content and composition using X-ray diffraction. Observations from core samples and geophysical logs are also used to establish alteration zones. Mineralogical data, geophysical log data and physical characteristics of the core suggest that the base of the Snake River Plain aquifer at the axial zone is located 960 m below the surface, much deeper than previously suspected. Swelling smectite clay clogs pore spaces and reduces porosity and permeability to create a natural base to the aquifer. Increased temperatures favor the formation of smectite clay and other secondary minerals to the bottom of the hole. Below 960 m the core shows signs of alteration including color change, formation of clay, and filling of other secondary minerals in vesicles and fractured zones of the core. The smectite clay observed is Fe-rich clay that is authigenic in some places. Geothermal power generation may be feasible using a low temperature hot water geothermal system if thermal fluids can be attained near the bottom of the Kimama well.

A case study of the Great Plains low-level jet using wind profiler network data and a high resolution mesoscale model

Energy Technology Data Exchange (ETDEWEB)

Zhong, S.; Fast, J.D.; Bian, X.; Stage, S. [Pacific Northwest National Lab., Richland, WA (United States)] [and others

1996-04-01

The Great Plains low-level jet (LLJ) has important effects on the life cycle of clouds and on radiative and surface heat and moisture fluxes at the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site. This diurnal phenomenon governs the transport and convergence of low-level moisture into the region and often leads to the development of clouds and precipitation. A full understanding of the life cycle of clouds at the SGP CART site and their proper representation in single column and global climate models cannot be obtained without an improved understanding of this important phenomenon.

A BaF2 crystal array for high energy -ray measurements

Indian Academy of Sciences (India)

A very well-known such array is called two-arm-photon- spectrometer (TAPS) [1]. It consists of large (25 cm long) hexagonal BaF¾ crystals ar- ranged in packs of 64 crystals. ... light which may not reach the photomultiplier tube. A sketch of the ...

Mid-Holocene hydrology change in the south Taihu area of the Yangtze delta plain, China, and its relationship to the development of Neolithic cultures

Science.gov (United States)

Chen, T.; Ryves, D.; Wang, Z.; Lewis, J.

2017-12-01

During the middle Holocene, the hydrological environments in the Taihu Plain, Yangtze Delta, China, varied tremendously under the influence of sea-level and climate change. Simultaneously, several Neolithic cultures, such as, the Majiabang, Songze, and Liangzhu culture, developed in this region. Basing on AMS14C dating, diatom identification, measurements of C-N elements and their stable isotopes of sediments from core DTX4 and DTX10, obtained in the East Tiaoxi Plain, south Taihu plain, we discussed the influence of hydrology changes on the development of Neolithic cultures. The results revealed that the East Tiaoxi River plain was in an estuary (the Palaeo-Taihu Estuary) condition at 7500 cal. yr BP, undergoing elevated in-fill in response to rapid sea-level rise. After 7500 cal. yr BP, low salinity conditions occurred, likely influenced by the Yangtze freshwater evidenced by constant occurrence of Aulacoseira granulata, which implied Yangtze runoff discharged along the channel of Palaeo-incised Taihu valley into the Hangzhou Bay during the middle Holocene. Sea-water penetration interrupted after 7000 cal. yr BP caused by an abrupt sea-level rise. During 6500-5600 cal. yr BP, sea-water retreated gradually, corresponding to the infilling of Palaeo-Taihu Estuary. Combing records from previously studied cores in the Taihu plain, stable freshwater condition (or dry land) established in most area of the Taihu plain after 5600 cal. yr BP due to the closure of the Palaeo-Taihu Estuary. We speculate that the low-salinity marsh started at about 7500-7000 cal. yr BP probably attracted the early Majiabang people to live around the Palaeo-Taihu Estuary. The sea water penetration between 7000-6500 cal. yr BP matches the left of the late Majiabang and the early-middle Songze people lived in the east of the Palaeo-Taihu Estuary, to the north and east of the Taihu Plain. The context of stable freshwater condition (or dry land) in the East Tiaoxi River plain promoted the

Great Plains Wind Energy Transmission Development Project

Energy Technology Data Exchange (ETDEWEB)

Brad G. Stevens, P.E.; Troy K. Simonsen; Kerryanne M. Leroux

2012-06-09

In fiscal year 2005, the Energy & Environmental Research Center (EERC) received funding from the U.S. Department of Energy (DOE) to undertake a broad array of tasks to either directly or indirectly address the barriers that faced much of the Great Plains states and their efforts to produce and transmit wind energy at the time. This program, entitled Great Plains Wind Energy Transmission Development Project, was focused on the central goal of stimulating wind energy development through expansion of new transmission capacity or development of new wind energy capacity through alternative market development. The original task structure was as follows: Task 1 - Regional Renewable Credit Tracking System (later rescoped to Small Wind Turbine Training Center); Task 2 - Multistate Transmission Collaborative; Task 3 - Wind Energy Forecasting System; and Task 4 - Analysis of the Long-Term Role of Hydrogen in the Region. As carried out, Task 1 involved the creation of the Small Wind Turbine Training Center (SWTTC). The SWTTC, located Grand Forks, North Dakota, consists of a single wind turbine, the Endurance S-250, on a 105-foot tilt-up guyed tower. The S-250 is connected to the electrical grid on the 'load side' of the electric meter, and the power produced by the wind turbine is consumed locally on the property. Establishment of the SWTTC will allow EERC personnel to provide educational opportunities to a wide range of participants, including grade school through college-level students and the general public. In addition, the facility will allow the EERC to provide technical training workshops related to the installation, operation, and maintenance of small wind turbines. In addition, under Task 1, the EERC hosted two small wind turbine workshops on May 18, 2010, and March 8, 2011, at the EERC in Grand Forks, North Dakota. Task 2 involved the EERC cosponsoring and aiding in the planning of three transmission workshops in the midwest and western regions. Under Task

Factors affecting the performance of large-aperture microphone arrays

Science.gov (United States)

Silverman, Harvey F.; Patterson, William R.; Sachar, Joshua

2002-05-01

Large arrays of microphones have been proposed and studied as a possible means of acquiring data in offices, conference rooms, and auditoria without requiring close-talking microphones. When such an array essentially surrounds all possible sources, it is said to have a large aperture. Large-aperture arrays have attractive properties of spatial resolution and signal-to-noise enhancement. This paper presents a careful comparison of theoretical and measured performance for an array of 256 microphones using simple delay-and-sum beamforming. This is the largest currently functional, all digital-signal-processing array that we know of. The array is wall-mounted in the moderately adverse environment of a general-purpose laboratory (8 m×8 m×3 m). The room has a T60 reverberation time of 550 ms. Reverberation effects in this room severely impact the array's performance. However, the width of the main lobe remains comparable to that of a simplified prediction. Broadband spatial resolution shows a single central peak with 10 dB gain about 0.4 m in diameter at the -3 dB level. Away from that peak, the response is approximately flat over most of the room. Optimal weighting for signal-to-noise enhancement degrades the spatial resolution minimally. Experimentally, we verify that signal-to-noise gain is less than proportional to the square root of the number of microphones probably due to the partial correlation of the noise between channels, to variation of signal intensity with polar angle about the source, and to imperfect correlation of the signal over the array caused by reverberations. We show measurements of the relative importance of each effect in our environment.

Precipitation Dynamical Downscaling Over the Great Plains

Science.gov (United States)

Hu, Xiao-Ming; Xue, Ming; McPherson, Renee A.; Martin, Elinor; Rosendahl, Derek H.; Qiao, Lei

2018-02-01

Detailed, regional climate projections, particularly for precipitation, are critical for many applications. Accurate precipitation downscaling in the United States Great Plains remains a great challenge for most Regional Climate Models, particularly for warm months. Most previous dynamic downscaling simulations significantly underestimate warm-season precipitation in the region. This study aims to achieve a better precipitation downscaling in the Great Plains with the Weather Research and Forecast (WRF) model. To this end, WRF simulations with different physics schemes and nudging strategies are first conducted for a representative warm season. Results show that different cumulus schemes lead to more pronounced difference in simulated precipitation than other tested physics schemes. Simply choosing different physics schemes is not enough to alleviate the dry bias over the southern Great Plains, which is related to an anticyclonic circulation anomaly over the central and western parts of continental U.S. in the simulations. Spectral nudging emerges as an effective solution for alleviating the precipitation bias. Spectral nudging ensures that large and synoptic-scale circulations are faithfully reproduced while still allowing WRF to develop small-scale dynamics, thus effectively suppressing the large-scale circulation anomaly in the downscaling. As a result, a better precipitation downscaling is achieved. With the carefully validated configurations, WRF downscaling is conducted for 1980-2015. The downscaling captures well the spatial distribution of monthly climatology precipitation and the monthly/yearly variability, showing improvement over at least two previously published precipitation downscaling studies. With the improved precipitation downscaling, a better hydrological simulation over the trans-state Oologah watershed is also achieved.

Regional implications of heat flow of the Snake River Plain, Northwestern United States

Science.gov (United States)

Blackwell, D. D.

1989-08-01

The Snake River Plain is a major topographic feature of the Northwestern United States. It marks the track of an upper mantle and crustal melting event that propagated across the area from southwest to northeast at a velocity of about 3.5 cm/yr. The melting event has the same energetics as a large oceanic hotspot or plume and so the area is the continental analog of an oceanic hotspot track such as the Hawaiian Island-Emperor Seamount chain. Thus, the unique features of the area reflect the response of a continental lithosphere to a very energetic hotspot. The crust is extensively modified by basalt magma emplacement into the crust and by the resulting massive rhyolite volcanism from melted crustal material, presently occurring at Yellowstone National Park. The volcanism is associated with little crustal extension. Heat flow values are high along the margins of the Eastern and Western Snake River Plains and there is abundant evidence for low-grade geothermal resources associated with regional groundwater systems. The regional heat flow pattern in the Western Snake River Plains reflects the influence of crustal-scale thermal refraction associated with the large sedimentary basin that has formed there. Heat flow values in shallow holes in the Eastern Snake River Plains are low due to the Snake River Plains aquifer, an extensive basalt aquifer where water flow rates approach 1 km/yr. Below the aquifer, conductive heat flow values are about 100 mW m -2. Deep holes in the region suggest a systematic eastward increase in heat flow in the Snake River Plains from about 75-90 mW m -2 to 90-110 mW m -2. Temperatures in the upper crust do not behave similarly because the thermal conductivity of the Plio-Pleistocene sedimentary rocks in the west is lower than that in the volcanic rocks characteristic of the Eastern Snake River Plains. Extremely high heat loss values (averaging 2500 mW m -2) and upper crustal temperatures are characteristic of the Yellowstone caldera.

Poster - Thurs Eve-09: Evaluation of a commercial 2D ion-chamber array for intensity modulated radiation therapy dose measurements.

Science.gov (United States)

Mei, X; Bracken, G; Kerr, A

2008-07-01

Experimental verification of calculated dose from a treatment planning system is often essential for quality assurance (QA) of intensity modulated radiation therapy (IMRT). Film dosimetry and single ion chamber measurements are commonly used for IMRT QA. Film dosimetry has very good spatial resolution, but is labor intensive and absolute dose is not reliable. Ion chamber measurements are still required for absolute dose after measurements using films. Dosimeters based on 2D detector arrays that can measure 2D dose in real-time are gaining wider use. These devices provide a much easier and reliable tool for IMRT QA. We report the evaluation of a commercial 2D ion chamber array, including its basic performance characteristics, such as linearity, reproducibility and uniformity of relative ion chamber sensitivities, and comparisons between measured 2D dose and calculated dose with a commercial treatment planning system. Our analysis shows this matrix has excellent linearity and reproducibility, but relative sensitivities are tilted such that the +Y region is over sensitive, while the -Y region is under sensitive. Despite this behavior, our results show good agreement between measured 2D dose profiles and Eclipse planned data for IMRT test plans and a few verification plans for clinical breast field-in-field plans. The gamma values (3% or 3 mm distance-to-agreement) are all less than 1 except for one or two pixels at the field edge This device provides a fast and reliable stand-alone dosimeter for IMRT QA. © 2008 American Association of Physicists in Medicine.

Phased Array Noise Source Localization Measurements of an F404 Nozzle Plume at Both Full and Model Scale

Science.gov (United States)

Podboy, Gary G.; Bridges, James E.; Henderson, Brenda S.

2010-01-01

A 48-microphone planar phased array system was used to acquire jet noise source localization data on both a full-scale F404-GE-F400 engine and on a 1/4th scale model of a F400 series nozzle. The full-scale engine test data show the location of the dominant noise sources in the jet plume as a function of frequency for the engine in both baseline (no chevron) and chevron configurations. Data are presented for the engine operating both with and without afterburners. Based on lessons learned during this test, a set of recommendations are provided regarding how the phased array measurement system could be modified in order to obtain more useful acoustic source localization data on high-performance military engines in the future. The data obtained on the 1/4th scale F400 series nozzle provide useful insights regarding the full-scale engine jet noise source mechanisms, and document some of the differences associated with testing at model-scale versus fullscale.

Endeavor cruise 071 navigation and bathymetry, northern Hatteras Abyssal Plain

International Nuclear Information System (INIS)

Laine, E.P.; Friedrich, N.E.; McCreery, C.; Dickson, S.; Baker, M.

1985-01-01

Sub-bottom seismic profiling was carried out by R/V Endeavor during the summers of 1980 and 1981. Data collection was concentrated in LLWODP study area E-N3, which encompasses the northern Hatteras Abyssal Plain and the adjacent lower continental rise. Time, position, and depth were logged and marked on the seismic record at 15-minute intervals. These navigational and bathymetric data have been used to produce a time/position/depth listing, and a detailed bathymetric map of the northern Hatteras Abyssal Plain and surrounding physiographic provinces. 6 figures, 1 table

Great plains regional climate assessment technical report

Science.gov (United States)

The Great Plains region (GP) plays important role in providing food and energy to the economy of the United States. Multiple climatic and non-climatic stressors put multiple sectors, livelihoods and communities at risk, including agriculture, water, ecosystems and rural and tribal communities. The G...

Measurement of impurity emission profiles in CHS Plasma using AXUV photodiode arrays and VUV bandpass filters

International Nuclear Information System (INIS)

Suzuki, C.; Peterson, B.J.; Ida, K.

2004-01-01

We have designed a compact and low-cost diagnostic system for spatiotemporal distributions of specific vacuum ultraviolet (VUV) emission lines from impurities in Compact Helical System (CHS) plasmas. The system consists of 20 channel absolute extreme ultraviolet photodiode arrays combined with interchangeable thin foil filters which have passbands in the VUV region. A compact mounting module which contains all the components including an in-vacuum preamplifier for immediate current-voltage conversion has been designed and successfully fabricated. A preliminary measurement with a single module using an aluminum foil filter has been carried out for monitoring the behavior of oxygen impurity in CHS, and initial results have been obtained. Two identical modules equipped with Versa Module European bus-based analog-digital converters will be available for future tomographic measurements

The Big Optical Array

International Nuclear Information System (INIS)

Mozurkewich, D.; Johnston, K.J.; Simon, R.S.

1990-01-01

This paper describes the design and the capabilities of the Naval Research Laboratory Big Optical Array (BOA), an interferometric optical array for high-resolution imaging of stars, stellar systems, and other celestial objects. There are four important differences between the BOA design and the design of Mark III Optical Interferometer on Mount Wilson (California). These include a long passive delay line which will be used in BOA to do most of the delay compensation, so that the fast delay line will have a very short travel; the beam combination in BOA will be done in triplets, to allow measurement of closure phase; the same light will be used for both star and fringe tracking; and the fringe tracker will use several wavelength channels

Statistically optimized near field acoustic holography using an array of pressure-velocity probes

DEFF Research Database (Denmark)

Jacobsen, Finn; Jaud, Virginie

2007-01-01

of a measurement aperture that extends well beyond the source can be relaxed. Both NAH and SONAH are based on the assumption that all sources are on one side of the measurement plane whereas the other side is source free. An extension of the SONAH procedure based on measurement with a double layer array...... of pressure microphones has been suggested. The double layer technique makes it possible to distinguish between sources on the two sides of the array and thus suppress the influence of extraneous noise coming from the “wrong” side. It has also recently been demonstrated that there are significant advantages...... in NAH based on an array of acoustic particle velocity transducers (in a single layer) compared with NAH based on an array of pressure microphones. This investigation combines the two ideas and examines SONAH based on an array of pressure-velocity intensity probes through computer simulations as well...

Ionospheric drift measurements on an array of six aerials

Energy Technology Data Exchange (ETDEWEB)

Kumar, V; Rai, R K

1976-03-01

Fading records were obtained using an array of six receiving aerials. A full correlation method of analysis was applied to estimate the drift and anisotropy parameters of the diffraction pattern. A study of simultaneous observations by triangles of different sizes and orientations leads to the conclusion that on an average, the larger triangle gives slightly higher values for the true drift speed and pattern size and slightly lower value for the random velocity. Also the major axis of the correlation ellipse exhibits a tendency for alignment along the largest side of the triangle.

Integrated Miniature Arrays of Optical Biomolecule Detectors

Science.gov (United States)

Iltchenko, Vladimir; Maleki, Lute; Lin, Ying; Le, Thanh

2009-01-01

Integrated miniature planar arrays of optical sensors for detecting specific biochemicals in extremely small quantities have been proposed. An array of this type would have an area of about 1 cm2. Each element of the array would include an optical microresonator that would have a high value of the resonance quality factor (Q . 107). The surface of each microresonator would be derivatized to make it bind molecules of a species of interest, and such binding would introduce a measurable change in the optical properties of the microresonator. Because each microresonator could be derivatized for detection of a specific biochemical different from those of the other microresonators, it would be possible to detect multiple specific biochemicals by simultaneous or sequential interrogation of all the elements in the array. Moreover, the derivatization would make it unnecessary to prepare samples by chemical tagging. Such interrogation would be effected by means of a grid of row and column polymer-based optical waveguides that would be integral parts of a chip on which the array would be fabricated. The row and column polymer-based optical waveguides would intersect at the elements of the array (see figure). At each intersection, the row and column waveguides would be optically coupled to one of the microresonators. The polymer-based waveguides would be connected via optical fibers to external light sources and photodetectors. One set of waveguides and fibers (e.g., the row waveguides and fibers) would couple light from the sources to the resonators; the other set of waveguides and fibers (e.g., the column waveguides and fibers) would couple light from the microresonators to the photodetectors. Each microresonator could be addressed individually by row and column for measurement of its optical transmission. Optionally, the chip could be fabricated so that each microresonator would lie inside a microwell, into which a microscopic liquid sample could be dispensed.

High-resolution Tangential AXUV Arrays for Radiated Power Density Measurements on NSTX-U

Energy Technology Data Exchange (ETDEWEB)

Delgado-Aparicio, L [PPPL; Bell, R E [PPPL; Faust, I [MIT; Tritz, K [The Johns Hopkins University, Baltimore, MD, 21209, USA; Diallo, A [PPPL; Gerhardt, S P [PPPL; Kozub, T A [PPPL; LeBlanc, B P [PPPL; Stratton, B C [PPPL

2014-07-01

Precise measurements of the local radiated power density and total radiated power are a matter of the uttermost importance for understanding the onset of impurity-induced instabilities and the study of particle and heat transport. Accounting of power balance is also needed for the understanding the physics of various divertor con gurations for present and future high-power fusion devices. Poloidal asymmetries in the impurity density can result from high Mach numbers and can impact the assessment of their flux-surface-average and hence vary the estimates of P[sub]rad (r, t) and (Z[sub]eff); the latter is used in the calculation of the neoclassical conductivity and the interpretation of non-inductive and inductive current fractions. To this end, the bolometric diagnostic in NSTX-U will be upgraded, enhancing the midplane coverage and radial resolution with two tangential views, and adding a new set of poloidally-viewing arrays to measure the 2D radiation distribution. These systems are designed to contribute to the near- and long-term highest priority research goals for NSTX-U which will integrate non-inductive operation at reduced collisionality, with high-pressure, long energy-confinement-times and a divertor solution with metal walls.

How much sugar do consumers add to plain yogurts? Insights from a study examining French consumer behavior and self-reported habits.

Science.gov (United States)

Saint-Eve, Anne; Leclercq, Hélène; Berthelo, Sébastien; Saulnier, Benjamin; Oettgen, Walther; Delarue, Julien

2016-04-01

In France, 50% of consumers sweeten plain yogurts prior to consumption. This study measured how much sugar consumers added under contextualized testing conditions. Participants (199 French adults who regularly consume plain yogurt adding sugar) were given a plain yogurt (125 g) at the end of a full meal and were allowed to sweeten it with their usual sweetener (caster sugar, honey, or jam). The quantities added were measured indirectly by weighing the sweetener containers before and after use; they were then converted into equivalent quantities of sucrose, or "added sugar." Participants were asked to describe their relative hunger, thirst, and liking for plain yogurt and to estimate the quantity of sweetener they had added. On average, participants added 13.6 g of sugar to their yogurts, which is higher than the 10.2 g of sugar contained in pre-sweetened commercial yogurts (125 g). More sugar was added when subjects used jam (24.4 g/yogurt, n = 36) as opposed to caster sugar (11.0 g/yogurt, n = 134) or honey (12.1 g/yogurt, n = 29). Age, socio-professional category, and BMI had a significant influence on added-sugar quantity. Based on behavior and attitude, participants could be separated into three evenly sized groups: "low sugar users" (n = 67, median = 6.1 g/yogurt), who tended to control their food intake, "medium sugar users" (n = 66, median = 11.4 g/yogurt), and "heavy sugar users" (n = 66, median = 19.9 g/yogurt) who sought immediate satisfaction. To our knowledge, this study is the first to provide robust data on the amount of sugar consumers add to plain yogurts in contextualized conditions (self preparation during a real meal). Our findings show that consumers underestimated by half the quantity of sweetener they added. Copyright © 2016 Elsevier Ltd. All rights reserved.

Resonance spectra of diabolo optical antenna arrays

Directory of Open Access Journals (Sweden)

Hong Guo

2015-10-01

Full Text Available A complete set of diabolo optical antenna arrays with different waist widths and periods was fabricated on a sapphire substrate by using a standard e-beam lithography and lift-off process. Fabricated diabolo optical antenna arrays were characterized by measuring the transmittance and reflectance with a microscope-coupled FTIR spectrometer. It was found experimentally that reducing the waist width significantly shifts the resonance to longer wavelength and narrowing the waist of the antennas is more effective than increasing the period of the array for tuning the resonance wavelength. Also it is found that the magnetic field enhancement near the antenna waist is correlated to the shift of the resonance wavelength.

Probe design for expression arrays using OligoWiz

DEFF Research Database (Denmark)

Wernersson, Rasmus

2014-01-01

Since all measurements from a DNA microarray is dependant on the probes used, a good choice of probes is of vital importa nce when designing custom micro-arrays. This chapter describes how to de sign expression arrays using the “ OligoWiz ” software suite. The general desired features of good...... probes and the issues which probe design must address are introduced and a conceptual (rather than mathematical) description of how OligoWiz scores the quality of th e potential probes is presented. This is followed by a detailed step-by-step guide to designing expression arrays with OligoWiz....

The History of the Environmental Conditions Research in the Braila Plain

OpenAIRE

Anca Gabriela Turtureanu

2015-01-01

The Romanian Plain has generally represented the study subject of research in the field of Geography and especially of the environment geography and resources. Due to the structure and the geological movements of the climate factors, the hydrography in the area of the Braila Plain has represents a subject of many geographers‘ interest. The divagation and the leaving of the water course phenomena of some rivers, the genesis and the classification of lake basins, underground waters, the links t...

Geodatabase compilation of hydrogeologic, remote sensing, and water-budget-component data for the High Plains aquifer, 2011

Science.gov (United States)

Houston, Natalie A.; Gonzales-Bradford, Sophia L.; Flynn, Amanda T.; Qi, Sharon L.; Peterson, Steven M.; Stanton, Jennifer S.; Ryter, Derek W.; Sohl, Terry L.; Senay, Gabriel B.

2013-01-01

The High Plains aquifer underlies almost 112 million acres in the central United States. It is one of the largest aquifers in the Nation in terms of annual groundwater withdrawals and provides drinking water for 2.3 million people. The High Plains aquifer has gained national and international attention as a highly stressed groundwater supply primarily because it has been appreciably depleted in some areas. The U.S. Geological Survey has an active program to monitor the changes in groundwater levels for the High Plains aquifer and has documented substantial water-level changes since predevelopment: the High Plains Groundwater Availability Study is part of a series of regional groundwater availability studies conducted to evaluate the availability and sustainability of major aquifers across the Nation. The goals of the regional groundwater studies are to quantify current groundwater resources in an aquifer system, evaluate how these resources have changed over time, and provide tools to better understand a systems response to future demands and environmental stresses. The purpose of this report is to present selected data developed and synthesized for the High Plains aquifer as part of the High Plains Groundwater Availability Study. The High Plains Groundwater Availability Study includes the development of a water-budget-component analysis for the High Plains completed in 2011 and development of a groundwater-flow model for the northern High Plains aquifer. Both of these tasks require large amounts of data about the High Plains aquifer. Data pertaining to the High Plains aquifer were collected, synthesized, and then organized into digital data containers called geodatabases. There are 8 geodatabases, 1 file geodatabase and 7 personal geodatabases, that have been grouped in three categories: hydrogeologic data, remote sensing data, and water-budget-component data. The hydrogeologic data pertaining to the northern High Plains aquifer is included in three separate

Groundwater Discharge along a Channelized Coastal Plain Stream

Energy Technology Data Exchange (ETDEWEB)

LaSage, Danita M [Ky Dept for natural resources, Div of Mine Permits; Sexton, Joshua L [JL Sexton and Son; Mukherjee, Abhijit [Univ of Tx, Jackson School of Geosciences, Bur of Econ. Geology; Fryar, Alan E [Univ of KY, Dept of Earth and Geoligical Sciences; Greb, Stephen F [Univ of KY, KY Geological Survey

2015-10-01

In the Coastal Plain of the southeastern USA, streams have commonly been artificially channelized for flood control and agricultural drainage. However, groundwater discharge along such streams has received relatively little attention. Using a combination of stream- and spring-flow measurements, spring temperature measurements, temperature profiling along the stream-bed, and geologic mapping, we delineated zones of diffuse and focused discharge along Little Bayou Creek, a channelized, first-order perennial stream in western Kentucky. Seasonal variability in groundwater discharge mimics hydraulic-head fluctuations in a nearby monitoring well and spring-discharge fluctuations elsewhere in the region, and is likely to reflect seasonal variability in recharge. Diffuse discharge occurs where the stream is incised into the semi-confined regional gravel aquifer, which is comprised of the Mounds Gravel. Focused discharge occurs upstream where the channel appears to have intersected preferential pathways within the confining unit. Seasonal fluctuations in discharge from individual springs are repressed where piping results in bank collapse. Thereby, focused discharge can contribute to the morphological evolution of the stream channel.

Coupling in reflector arrays

DEFF Research Database (Denmark)

Appel-Hansen, Jørgen

1968-01-01

In order to reduce the space occupied by a reflector array, it is desirable to arrange the array antennas as close to each other as possible; however, in this case coupling between the array antennas will reduce the reflecting properties of the reflector array. The purpose of the present communic......In order to reduce the space occupied by a reflector array, it is desirable to arrange the array antennas as close to each other as possible; however, in this case coupling between the array antennas will reduce the reflecting properties of the reflector array. The purpose of the present...

Groundwater declines are linked to changes in Great Plains stream fish assemblages.

Science.gov (United States)

Perkin, Joshuah S; Gido, Keith B; Falke, Jeffrey A; Fausch, Kurt D; Crockett, Harry; Johnson, Eric R; Sanderson, John

2017-07-11

Groundwater pumping for agriculture is a major driver causing declines of global freshwater ecosystems, yet the ecological consequences for stream fish assemblages are rarely quantified. We combined retrospective (1950-2010) and prospective (2011-2060) modeling approaches within a multiscale framework to predict change in Great Plains stream fish assemblages associated with groundwater pumping from the United States High Plains Aquifer. We modeled the relationship between the length of stream receiving water from the High Plains Aquifer and the occurrence of fishes characteristic of small and large streams in the western Great Plains at a regional scale and for six subwatersheds nested within the region. Water development at the regional scale was associated with construction of 154 barriers that fragment stream habitats, increased depth to groundwater and loss of 558 km of stream, and transformation of fish assemblage structure from dominance by large-stream to small-stream fishes. Scaling down to subwatersheds revealed consistent transformations in fish assemblage structure among western subwatersheds with increasing depths to groundwater. Although transformations occurred in the absence of barriers, barriers along mainstem rivers isolate depauperate western fish assemblages from relatively intact eastern fish assemblages. Projections to 2060 indicate loss of an additional 286 km of stream across the region, as well as continued replacement of large-stream fishes by small-stream fishes where groundwater pumping has increased depth to groundwater. Our work illustrates the shrinking of streams and homogenization of Great Plains stream fish assemblages related to groundwater pumping, and we predict similar transformations worldwide where local and regional aquifer depletions occur.

High-Speed Monitoring of Multiple Grid-Connected Photovoltaic Array Configurations and Supplementary Weather Station.

Science.gov (United States)

Boyd, Matthew T

2017-06-01

Three grid-connected monocrystalline silicon photovoltaic arrays have been instrumented with research-grade sensors on the Gaithersburg, MD campus of the National Institute of Standards and Technology (NIST). These arrays range from 73 kW to 271 kW and have different tilts, orientations, and configurations. Irradiance, temperature, wind, and electrical measurements at the arrays are recorded, and images are taken of the arrays to monitor shading and capture any anomalies. A weather station has also been constructed that includes research-grade instrumentation to measure all standard meteorological quantities plus additional solar irradiance spectral bands, full spectrum curves, and directional components using multiple irradiance sensor technologies. Reference photovoltaic (PV) modules are also monitored to provide comprehensive baseline measurements for the PV arrays. Images of the whole sky are captured, along with images of the instrumentation and reference modules to document any obstructions or anomalies. Nearly, all measurements at the arrays and weather station are sampled and saved every 1s, with monitoring having started on Aug. 1, 2014. This report describes the instrumentation approach used to monitor the performance of these photovoltaic systems, measure the meteorological quantities, and acquire the images for use in PV performance and weather monitoring and computer model validation.

Optical performance of prototype horn-coupled TES bolometer arrays for SAFARI

Science.gov (United States)

Audley, Michael D.; de Lange, Gert; Gao, Jian-Rong; Khosropanah, Pourya; Hijmering, Richard; Ridder, Marcel L.

2016-07-01

The SAFARI Detector Test Facility is an ultra-low background optical testbed for characterizing ultra-sensitive prototype horn-coupled TES bolmeters for SAFARI, the grating spectrometer on board the proposed SPICA satellite. The testbed contains internal cold and hot black-body illuminators and a light-pipe for illumination with an external source. We have added reimaging optics to facilitate array optical measurements. The system is now being used for optical testing of prototype detector arrays read out with frequency-domain multiplexing. We present our latest optical measurements of prototype arrays and discuss these in terms of the instrument performance.

Creep of plain weave polymer matrix composites

Science.gov (United States)

Gupta, Abhishek

Polymer matrix composites are increasingly used in various industrial sectors to reduce structural weight and improve performance. Woven (also known as textile) composites are one class of polymer matrix composites with increasing market share mostly due to their lightweight, their flexibility to form into desired shape, their mechanical properties and toughness. Due to the viscoelasticity of the polymer matrix, time-dependent degradation in modulus (creep) and strength (creep rupture) are two of the major mechanical properties required by engineers to design a structure reliably when using these materials. Unfortunately, creep and creep rupture of woven composites have received little attention by the research community and thus, there is a dire need to generate additional knowledge and prediction models, given the increasing market share of woven composites in load bearing structural applications. Currently, available creep models are limited in scope and have not been validated for any loading orientation and time period beyond the experimental time window. In this thesis, an analytical creep model, namely the Modified Equivalent Laminate Model (MELM), was developed to predict tensile creep of plain weave composites for any orientation of the load with respect to the orientation of the fill and warp fibers, using creep of unidirectional composites. The ability of the model to predict creep for any orientation of the load is a "first" in this area. The model was validated using an extensive experimental involving the tensile creep of plain weave composites under varying loading orientation and service conditions. Plain weave epoxy (F263)/ carbon fiber (T300) composite, currently used in aerospace applications, was procured as fabrics from Hexcel Corporation. Creep tests were conducted under two loading conditions: on-axis loading (0°) and off-axis loading (45°). Constant load creep, in the temperature range of 80-240°C and stress range of 1-70% UTS of the

Groundwater availability in the Atlantic Coastal Plain of North and South Carolina

Science.gov (United States)

Campbell, Bruce G.; Coes, Alissa L.

2010-01-01

The Atlantic Coastal Plain aquifers and confining units of North and South Carolina are composed of crystalline carbonate rocks, sand, clay, silt, and gravel and contain large volumes of high-quality groundwater. The aquifers have a long history of use dating back to the earliest days of European settlement in the late 1600s. Although extensive areas of some of the aquifers have or currently (2009) are areas of groundwater level declines from large-scale, concentrated pumping centers, large areas of the Atlantic Coastal Plain contain substantial quantities of high-quality groundwater that currently (2009) are unused. Groundwater use from the Atlantic Coastal Plain aquifers in North Carolina and South Carolina has increased during the past 60 years as the population has increased along with demands for municipal, industrial, and agricultural water needs. While North Carolina and South Carolina work to increase development of water supplies in response to the rapid growth in these coastal populations, both States recognize that they are facing a number of unanswered questions regarding availability of groundwater supplies and the best methods to manage these important supplies. An in-depth assessment of groundwater availability of the Atlantic Coastal Plain aquifers of North and South Carolina has been completed by the U.S. Geological Survey Groundwater Resources Program. This assessment includes (1) a determination of the present status of the Atlantic Coastal Plain groundwater resources; (2) an explanation for how these resources have changed over time; and (3) development of tools to assess the system's response to stresses from potential future climate variability. Results from numerous previous investigations of the Atlantic Coastal Plain by Federal and State agencies have been incorporated into this effort. The primary products of this effort are (1) comprehensive hydrologic datasets such as groundwater levels, groundwater use, and aquifer properties; (2) a

Estimating SGD flux in the Pingtung Plain coastal area by using Radon and Radium isotopes

Science.gov (United States)

Li Chang, Yao; Chieh Su, Chih

2015-04-01

In the past two decades, submarine groundwater discharge (SGD) has been recognized as an important pathway to transport material into coastal area. Our study area is located at Pingtung Plain which is the second largest plain in Taiwan with three major rivers, including Gaoping, Donggang and Linbian Rivers, flow through the plain. The Gaoping River, which has the largest drainage area, flows throughout the central part of the plain. The Pingtung Plain composed by four aquifers in different depths (0, 50, 100, and 200 m) and each layer extends to coastal area. Groundwater is an important water resource for local agriculture and aquaculture. However, the long-term over-pumping induced subsidence problem makes salinization at some coastal area. Some previous studies pointed out the SGD accounts for 80% or more of the mass of freshwater in Fangshan coast, depends on salinity and stable isotopes research. In this study, the radioactive tracers, Radon (222Rn, T1/2=3.8 d) and short-lived Ra isotopes (223Ra, T1/2=11.4 d & 224Ra, T1/2=3.6 d) are used in tracing SGD off the Pingtung Plain. During 2013 to 2014, the terrestrial water samples were collected from Gaoping, Donggang, Linbian Rivers and springs in different seasons. We also conducted two coastal waters cruises by using R/V Ocean Researcher 3 (OR3-1768 and 1799 cruises in May and September 2014). Continuous 222Rn was measured by RAD7 equipped with RAD-AQUA system and large volume (20 L) seawater samples were collected by CTD/Rosette water sampler with Niskin sterile bottles. Water samples were flow through Mn-fiber (flow rate < 1 LPM) to concentrate the Ra isotopes, and counted via RaDeCC system. In spatial variation, our result shows the excess 224Ra in the downstream of Gaoping River (2.39 dpm 100L-1) is higher than upstream (1.09 dpm 100L-1). It indicates the groundwater input may play an important role at the downstream of Gaoping River. For temporal variation, excess 224Ra in the Gaoping River are higher in wet

Estimating Groundwater Development area in Jianan Plain using Standardized Groundwater Index

Science.gov (United States)

Yu, Chang Hsiang; Haw, Lee Cheng

2017-04-01

Taiwan has been facing severe water crises in recent years owing to the effects of extreme weather conditions. Changes in precipitation patterns have also made the drought phenomenon increasingly prominent, which has indirectly affected groundwater recharge. Hence, in the present study, long-term monitoring data were collected from the study area of the Jianan plain. The standardized groundwater index (SGI) and was then used to analyse the region's drought characteristics. To analyse the groundwater level by using SGI, making SGI180 groundwater level be the medium water crises, and SGI360 groundwater level be the extreme water crises. Through the different water crises signal in SGI180 and SGI360, we divide groundwater in Jianan plain into two sections. Thereby the water crises indicators establishing groundwater level standard line in Jianan Plain, then using the groundwater level standard line to find the study area where could be groundwater development area in Jianan plain. Taking into account relatively more water scarcity in dry season, so the study screen out another emergency backup groundwater development area, but the long-term groundwater development area is still as a priority development area. After finding suitable locations, groundwater modeling systems(GMS) software is used to simulate our sites to evaluate development volume. Finally, the result of study will help the government to grasp the water shortage situation immediately and solve the problem of water resources deployment.

Non-invasive measurement of thyroid hormone in feces of a diverse array of avian and mammalian species.

Science.gov (United States)

Wasser, Samuel K; Azkarate, Jurgi Cristòbal; Booth, Rebecca K; Hayward, Lisa; Hunt, Kathleen; Ayres, Katherine; Vynne, Carly; Gobush, Kathleen; Canales-Espinosa, Domingo; Rodríguez-Luna, Ernesto

2010-08-01

We developed and validated a non-invasive thyroid hormone measure in feces of a diverse array of birds and mammals. An I(131) radiolabel ingestion study in domestic dogs coupled with High Pressure Liquid Chromatography (HPLC) analysis, showed that peak excretion in feces occurred at 24-48h post-ingestion, with I(131)-labelled thyroid hormone metabolites excreted primarily as triiodothyronine (T3) and relatively little thyroxine (T4), at all excretion times examined. The immunoreactive T3 profile across these same HPLC fractions closely corresponded with the I(131) radioactive profile. By contrast, the T4 immunoreactive profile was disproportionately high, suggesting that T4 excretion included a high percentage of T4 stores. We optimized and validated T3 and T4 extraction and assay methods in feces of wild northern spotted owls, African elephants, howler monkeys, caribou, moose, wolf, maned wolf, killer whales and Steller sea lions. We explained 99% of the variance in high and low T3 concentrations derived from species-specific sample pools, after controlling for species and the various extraction methods tested. Fecal T3 reflected nutritional deficits in two male and three female howler monkeys held in captivity for translocation from a highly degraded habitat. Results suggest that thyroid hormone can be accurately and reliably measured in feces, providing important indices for environmental physiology across a diverse array of birds and mammals. Copyright 2010 Elsevier Inc. All rights reserved.

Saturation measurement accuracy in clinical near-infrared cerebral oximeters with a 3D-printed channel array phantom