Strontium isotopic composition of hot spring and mineral spring waters, Japan

International Nuclear Information System (INIS)

Notsu, Kenji; Wakita, Hiroshi; Nakamura, Yuji

1991-01-01

In Japan, hot springs and mineral springs are distributed in Quaternary and Neogene volcanic regions as well as in granitic, sedimentary and metamorphic regions lacking in recent volcanic activity. The 87 Sr/ 86 Sr ratio was determined in hot spring and mineral spring waters obtained from 47 sites. The ratios of waters from Quaternary and Neogene volcanic regions were in the range 0.703-0.708, which is lower than that from granitic, sedimentary and metamorphic regions (0.706-0.712). The geographical distribution of the ratios coincides with the bedrock geology, and particularly the ratios of the waters in Quaternary volcanic regions correlate with those of surrounding volcanic rocks. These features suggest that subsurface materials control the 87 Sr/ 86 Sr ratios of soluble components in the hot spring and mineral spring waters. (author)

A natural tracer investigation of the hydrological regime of Spring Creek Springs, the largest submarine spring system in Florida

Science.gov (United States)

Dimova, Natasha T.; Burnett, William C.; Speer, Kevin

2011-04-01

This work presents results from a nearly two-year monitoring of the hydrologic dynamics of the largest submarine spring system in Florida, Spring Creek Springs. During the summer of 2007 this spring system was observed to have significantly reduced flow due to persistent drought conditions. Our examination of the springs revealed that the salinity of the springs' waters had increased significantly, from 4 in 2004 to 33 in July 2007 with anomalous high radon ( 222Rn, t1/2=3.8 days) in surface water concentrations indicating substantial saltwater intrusion into the local aquifer. During our investigation from August 2007 to May 2009 we deployed on an almost monthly basis a continuous radon-in-water measurement system and monitored the salinity fluctuations in the discharge area. To evaluate the springs' freshwater flux we developed three different models: two of them are based on water velocity measurements and either salinity or 222Rn in the associated surface waters as groundwater tracers. The third approach used only salinity changes within the spring area. The three models showed good agreement and the results confirmed that the hydrologic regime of the system is strongly correlated to local precipitation and water table fluctuations with higher discharges after major rain events and very low, even reverse flow during prolong droughts. High flow spring conditions were observed twice during our study, in the early spring and mid-late summer of 2008. However the freshwater spring flux during our observation period never reached that reported from a 1970s value of 4.9×10 6 m 3/day. The maximum spring flow was estimated at about 3.0×10 6 m 3/day after heavy precipitation in February-March 2008. As a result of this storm (total of 173 mm) the salinity in the spring area dropped from about 27 to 2 in only two days. The radon-in-water concentrations dramatically increased in parallel, from about 330 Bq/m 3 to about 6600 Bq/m 3. Such a rapid response suggests a direct

Instant Spring Tool Suite

CERN Document Server

Chiang, Geoff

2013-01-01

Filled with practical, step-by-step instructions and clear explanations for the most important and useful tasks. A tutorial guide that walks you through how to use the features of Spring Tool Suite using well defined sections for the different parts of Spring.Instant Spring Tool Suite is for novice to intermediate Java developers looking to get a head-start in enterprise application development using Spring Tool Suite and the Spring framework. If you are looking for a guide for effective application development using Spring Tool Suite, then this book is for you.

Pro Spring Integration

CERN Document Server

Lui, M; Chan, Andy; Long, Josh

2011-01-01

Pro Spring Integration is an authoritative book from the experts that guides you through the vast world of enterprise application integration (EAI) and application of the Spring Integration framework towards solving integration problems. The book is:. * An introduction to the concepts of enterprise application integration * A reference on building event-driven applications using Spring Integration * A guide to solving common integration problems using Spring Integration What makes this book unique is its coverage of contemporary technologies and real-world information, with a focus on common p

Mercury content in Hot Springs

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, R

1974-01-01

A method of determination of mercury in hot spring waters by flameless atomic absorption spectrophotometry is described. Further, the mercury content and the chemical behavior of the elementary mercury in hot springs are described. Sulfide and iodide ions interfered with the determination of mercury by the reduction-vapor phase technique. These interferences could, however, be minimized by the addition of potassium permanganate. Waters collected from 55 hot springs were found to contain up to 26.0 ppb mercury. High concentrations of mercury have been found in waters from Shimoburo Springs, Aomori (10.0 ppb), Osorezan Springs, Aomori (1.3 approximately 18.8 ppb), Gosyogake Springs, Akita (26.0 ppb), Manza Springs, Gunma (0.30 approximately 19.5 ppb) and Kusatu Springs, Gunma (1.70 approximately 4.50 ppb). These hot springs were acid waters containing a relatively high quantity of chloride or sulfate.

Groundwater monitoring strategies at the Weldon Spring site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Meyer, K.A. Jr.

1988-01-01

This paper presents groundwater monitoring strategies at the Weldon Spring Site in east-central Missouri. The Weldon Spring Site is former ordnance works and uranium processing facility. In 1987, elevated levels of inorganic anions and nitroaromatics were detected in groundwater beneath the site. Studies are currently underway to characterize the hydrogeologic regime and to define groundwater contamination. The complex hydrogeology at the Weldon Spring Site requires innovative monitoring strategies. Combinations of fracture and conduit flow exist in the limestone bedrock. Perched zones are also present near surface impoundments. Losing streams and springs surround the site. Confronting this complex combination of hydrogeologic conditions is especially challenging

Visit to valuable water springs. 22. ; Kanazawa spring and springs at the mountain flank of Iwate volcano. Meisui wo tazunete. 22. ; Kanazawa shimizu to Iwate sanroku yusuigun

Energy Technology Data Exchange (ETDEWEB)

Itadera, K. (Kanagawa Hot Springs Research Institute, Kanagawa (Japan)); Shimano, Y. (Utsunomiya Bunsei Junior College, Tochigi (Japan))

1993-06-30

This paper describes the following matters on the springs at the mountain flank of Iwate volcano in Iwate Prefecture, with the Kanazawa spring as the main subject: The new and old Iwate volcanos have rock-bed flow deposits which resulted from mountain disintegration, distributed over their south, east and north flanks, and most of the spring water wells up in these areas; the south, east and north flanks have about 80 springs, about 30 springs, and about 10 springs, respectively; the number of springs and the water well-up scale show a trend of inverse proportion; the Kanazawa spring is a generic name of the several springs located on the north flank in the Kanazawa area; its main spring forms a spring pond with an area of about 100 m[sup 2] with a spring water temperature of about 11.5[degree]C, electric conductivity of 200 [mu] S/cm or higher, and a flow-out rate of 500 l/s or more; the Kanazawa spring is characterized by having as large total dissolved component amount as 170 mg/l or more and abundant amount of SO4[sup 2-] and Cl[sup -]; and the spring presents properties different from those in other springs. 10 refs., 5 figs., 1 tab.

Spring integration essentials

CERN Document Server

Pandey, Chandan

2015-01-01

This book is intended for developers who are either already involved with enterprise integration or planning to venture into the domain. Basic knowledge of Java and Spring is expected. For newer users, this book can be used to understand an integration scenario, what the challenges are, and how Spring Integration can be used to solve it. Prior experience of Spring Integration is not expected as this book will walk you through all the code examples.

Getting started with Spring Framework a hands-on guide to begin developing applications using Spring Framework

CERN Document Server

Sharma, J

2016-01-01

Getting started with Spring Framework is a hands-on guide to begin developing applications using Spring Framework. The examples (consisting of 74 sample projects) that accompany this book are based on Spring 4.3 and Java 8. You can download the examples described in this book from the following GitHub project:github.com/getting-started-with-spring/3rdEdition This book is meant for Java developers with little or no knowledge of Spring Framework. Getting started with Spring Framework, Third Edition has been updated to reflect changes in Spring 4.3 and also includes new chapters on Java-based configuration and Spring Data (covers Spring Data JPA and Spring Data MongoDB projects). The existing chapters have been revised to include information on Java-based configuration. The book also includes some new information on bean definition profiles, importing application context XML files, lazy autowiring, creating custom qualifier annotations, JSR 349 annotations, spring-messaging module, Java 8's Optional type, and s...

The source, discharge, and chemical characteristics of water from Agua Caliente Spring, Palm Springs, California

Science.gov (United States)

Contributors: Brandt, Justin; Catchings, Rufus D.; Christensen, Allen H.; Flint, Alan L.; Gandhok, Gini; Goldman, Mark R.; Halford, Keith J.; Langenheim, V.E.; Martin, Peter; Rymer, Michael J.; Schroeder, Roy A.; Smith, Gregory A.; Sneed, Michelle; Martin, Peter

2011-01-01

Agua Caliente Spring, in downtown Palm Springs, California, has been used for recreation and medicinal therapy for hundreds of years and currently (2008) is the source of hot water for the Spa Resort owned by the Agua Caliente Band of the Cahuilla Indians. The Agua Caliente Spring is located about 1,500 feet east of the eastern front of the San Jacinto Mountains on the southeast-sloping alluvial plain of the Coachella Valley. The objectives of this study were to (1) define the geologic structure associated with the Agua Caliente Spring; (2) define the source(s), and possibly the age(s), of water discharged by the spring; (3) ascertain the seasonal and longer-term variability of the natural discharge, water temperature, and chemical characteristics of the spring water; (4) evaluate whether water-level declines in the regional aquifer will influence the temperature of the spring discharge; and, (5) estimate the quantity of spring water that leaks out of the water-collector tank at the spring orifice.

Spring plant phenology and false springs in the conterminous US during the 21st century

Science.gov (United States)

Allstadt, Andrew J.; Vavrus, Stephen J.; Heglund, Patricia J.; Pidgeon, Anna M.; Thogmartin, Wayne E.; Radeloff, Volker C.

2015-01-01

The onset of spring plant growth has shifted earlier in the year over the past several decades due to rising global temperatures. Earlier spring onset may cause phenological mismatches between the availability of plant resources and dependent animals, and potentially lead to more false springs, when subsequent freezing temperatures damage new plant growth. We used the extended spring indices to project changes in spring onset, defined by leaf out and by first bloom, and predicted false springs until 2100 in the conterminous United States (US) using statistically-downscaled climate projections from the Coupled Model Intercomparison Project 5 ensemble. Averaged over our study region, the median shift in spring onset was 23 days earlier in the Representative Concentration Pathway 8.5 scenario with particularly large shifts in the Western US and the Great Plains. Spatial variation in phenology was due to the influence of short-term temperature changes around the time of spring onset versus season long accumulation of warm temperatures. False spring risk increased in the Great Plains and portions of the Midwest, but remained constant or decreased elsewhere. We conclude that global climate change may have complex and spatially variable effects on spring onset and false springs, making local predictions of change difficult.

Ground water monitoring strategies at the Weldon Spring Site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Meyer, K.A. Jr.

1988-01-01

This paper presents ground water monitoring strategies at the Weldon Spring Site in east-central Missouri. The Weldon Spring Site is a former ordnance works and uranium processing facility. In 1987, elevated levels of inorganic anions and nitroaromatics were detected in ground water beneath the site. Studies are currently underway to characterize the hydrogeologic regime and to define ground water contamination. The complex hydrogeology at the Weldon Spring Site requires innovative monitoring strategies. Combinations of fracture and conduit flow exist in the limestone bedrock. Perched zones are also present near surface impoundments. Losing streams and springs surround the site. Solving this complex combination of hydrogeologic conditions is especially challenging

Optimum Design of a Coil Spring for Improving the Performance of a Spring -Operated Mechanism

International Nuclear Information System (INIS)

Lee, Dae Woo; Sohn, Jeong Hyun; Yoo, Wan Suk

2016-01-01

In this study, a release test bed is designed to evaluate the dynamic behaviors of a coil spring. From the release tests, the dynamic behaviors of a coil spring are analyzed. A lumped parameter spring model was established for numerical simulation of a spring. The design variables of a coil spring are optimized by using the design of experiments approach. Two-level factorial designs are used for the design optimization, and the primary effects of the design variables are analyzed. Based on the results of the interaction analysis and design sensitivity analysis, the level of the design variables is rearranged. Finally, the mixed-level factorial design is used for the optimum design process. According to the optimum design of the opening spring, the dynamic performance of the spring-operated mechanism increases by 2.90

Hot springs in Hokuriku District

Energy Technology Data Exchange (ETDEWEB)

Sato, K. (Hot Springs Research Center, Japan)

1971-01-01

In the Hokuriku district including Toyama, Ishikawa, and Fukui Prefectures, hot springs of more than 25/sup 0/C were investigated. In the Toyama Prefecture, there are 14 hot springs which are located in an area from the Kurobe River to the Tateyama volcano and in the mountainous area in the southwest. In Ishikawa Prefecture there are 16 hot springs scattered in Hakusan and its vicinity, the Kaga mountains, and in the Noto peninsula. In northern Fukui Prefecture there are seven hot springs. The hot springs in Shirakawa in Gifu Prefecture are characterized as acid springs producing exhalations and H/sub 2/S. These are attributed to the Quaternary volcanoes. The hot springs of Wakura, Katayamazu, and Awara in Ishikawa Prefecture are characterized by a high Cl content which is related to Tertiary andesite. The hot springs of Daishoji, Yamanaka, Yamashiro, Kuritsu, Tatsunokuchi, Yuwaku, and Yunotani are characterized by a low HCO/sub 3/ content. The Ca and SO/sub 4/ content decreases from east to west, and the Na and Cl content increases from west to east. These fluctuations are related to the Tertiary tuff and rhyolite. The hot springs of Kuronagi, Kinshu, and Babadani, located along the Kurobe River are characterized by low levels of dissolved components and high CO/sub 2/ and HCO/sub 3/ content. These trends are related to late Paleozoic granite. Hot springs resources are considered to be connected to geothermal resources. Ten tables, graphs, and maps are provided.

Spheres of discharge of springs

Science.gov (United States)

Springer, Abraham E.; Stevens, Lawrence E.

2009-02-01

Although springs have been recognized as important, rare, and globally threatened ecosystems, there is as yet no consistent and comprehensive classification system or common lexicon for springs. In this paper, 12 spheres of discharge of springs are defined, sketched, displayed with photographs, and described relative to their hydrogeology of occurrence, and the microhabitats and ecosystems they support. A few of the spheres of discharge have been previously recognized and used by hydrogeologists for over 80 years, but others have only recently been defined geomorphologically. A comparison of these spheres of discharge to classification systems for wetlands, groundwater dependent ecosystems, karst hydrogeology, running waters, and other systems is provided. With a common lexicon for springs, hydrogeologists can provide more consistent guidance for springs ecosystem conservation, management, and restoration. As additional comprehensive inventories of the physical, biological, and cultural characteristics are conducted and analyzed, it will eventually be possible to associate spheres of discharge with discrete vegetation and aquatic invertebrate assemblages, and better understand the habitat requirements of rare or unique springs species. Given the elevated productivity and biodiversity of springs, and their highly threatened status, identification of geomorphic similarities among spring types is essential for conservation of these important ecosystems.

Coil spring venting arrangement

International Nuclear Information System (INIS)

McCugh, R.M.

1975-01-01

A simple venting device for trapped gas pockets in hydraulic systems is inserted through a small access passages, operated remotely, and removed completely. The device comprises a small diameter, closely wound coil spring which is pushed through a guide temporarily inserted in the access passage. The guide has a central passageway which directs the coil spring radially upward into the pocket, so that, with the guide properly positioned for depth and properly oriented, the coil spring can be pushed up into the top of the pocket to vent it. By positioning a seal around the free end of the guide, the spring and guide are removed and the passage is sealed

Comparative spring mechanics in mantis shrimp.

Science.gov (United States)

Patek, S N; Rosario, M V; Taylor, J R A

2013-04-01

Elastic mechanisms are fundamental to fast and efficient movements. Mantis shrimp power their fast raptorial appendages using a conserved network of exoskeletal springs, linkages and latches. Their appendages are fantastically diverse, ranging from spears to hammers. We measured the spring mechanics of 12 mantis shrimp species from five different families exhibiting hammer-shaped, spear-shaped and undifferentiated appendages. Across species, spring force and work increase with size of the appendage and spring constant is not correlated with size. Species that hammer their prey exhibit significantly greater spring resilience compared with species that impale evasive prey ('spearers'); mixed statistical results show that species that hammer prey also produce greater work relative to size during spring loading compared with spearers. Disabling part of the spring mechanism, the 'saddle', significantly decreases spring force and work in three smasher species; cross-species analyses show a greater effect of cutting the saddle on the spring force and spring constant in species without hammers compared with species with hammers. Overall, the study shows a more potent spring mechanism in the faster and more powerful hammering species compared with spearing species while also highlighting the challenges of reconciling within-species and cross-species mechanical analyses when different processes may be acting at these two different levels of analysis. The observed mechanical variation in spring mechanics provides insights into the evolutionary history, morphological components and mechanical behavior, which were not discernible in prior single-species studies. The results also suggest that, even with a conserved spring mechanism, spring behavior, potency and component structures can be varied within a clade with implications for the behavioral functions of power-amplified devices.

Mockito for Spring

CERN Document Server

Acharya, Sujoy

2015-01-01

If you are an application developer with some experience in software testing and want to learn more about testing frameworks, then this technology and book is for you. Mockito for Spring will be perfect as your next step towards becoming a competent software tester with Spring and Mockito.

Characterization of the hydrogeology of the sacred Gihon Spring, Jerusalem: a deteriorating urban karst spring

Science.gov (United States)

Amiel, Ronit Benami; Grodek, Tamir; Frumkin, Amos

2010-09-01

The Gihon Spring, Jerusalem, is important for the major monotheistic religions. Its hydrogeology and hydrochemistry is studied here in order to understand urbanization effects on karst groundwater resources, and promote better water management. High-resolution monitoring of the spring discharge, temperature and electrical conductivity, was performed, together with chemical and bacterial analysis. All these demonstrate a rapid response of the spring to rainfall events and human impact. A complex karst system is inferred, including conduit flow, fissure flow and diffuse flow. Electrical conductivity, Na+ and K+ values (2.0 mS/cm, 130 and 50 mg/l respectively) are very high compared to other nearby springs located at the town margins (0.6 mS/cm, 15 and <1 mg/l respectively), indicating considerable urban pollution in the Gihon area. The previously cited pulsating nature of the spring was not detected during the present high-resolution monitoring. This phenomenon may have ceased due to additional water sources from urban leakage and irrigation feeding the spring. The urbanization of the recharge catchment thus affects the spring water dramatically, both chemically and hydrologically. Appropriate measures should therefore be undertaken to protect the Gihon Spring and other karst aquifers threatened by rapid urbanization.

Executive summary: Weldon Spring Site Environmental Report for calendar year 1992. Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

Energy Technology Data Exchange (ETDEWEB)

1993-06-01

This report has been prepared to provide information about the public safety and environmental protection programs conducted by the Weldon Spring Site Remedial Action Project. The Weldon Spring site is located in southern St. Charles County, Missouri, approximately 48 km (30 mi) west of St. Louis. The site consists of two main areas, the Weldon Spring Chemical Plant and raffinate pits and the Weldon Spring Quarry. The objectives of the Site Environmental Report are to present a summary of data from the environmental monitoring program, to characterize trends and environmental conditions at the site, and to confirm compliance with environmental and health protection standards and requirements. The report also presents the status of remedial activities and the results of monitoring these activities to assess their impacts on the public and environment. The scope of the environmental monitoring program at the Weldon Spring site has changed since it was initiated. Previously, the program focused on investigations of the extent and level of contaminants in the groundwater, surface waters, buildings, and air at the site. In 1992, the level of remedial activities required monitoring for potential impacts of those activities, particularly on surface water runoff and airborne effluents. This report includes monitoring data from routine radiological and nonradiological sampling activities. These data include estimates of dose to the public from the Weldon Spring site; estimates of effluent releases; and trends in groundwater contaminant levels. Also, applicable compliance requirements, quality assurance programs, and special studies conducted in 1992 to support environmental protection programs are reviewed.

Recent trend of administration on hot springs

Energy Technology Data Exchange (ETDEWEB)

Okubo, Shigeru [Environment Agency, Tokyo (Japan)

1989-01-01

The Environmental Agency exercises jurisdiction over Hot Spring Act, and plans to protect the source of the hot spring and to utilize it appropriately. From the aspect of utilization, hot springs are widely used as a means to remedy chronic diseases and tourist spots besides places for recuperation and repose. Statistics on Japanese hot springs showed that the number of hot spring spots and utilized-fountainhead increased in 1987, compared with the number in 1986. Considering the utilized-headspring, the number of naturally well-out springs has stabilized for 10 years while power-operated springs have increased. This is because the demand of hot springs has grown as the number of users has increased. Another reason is to keep the amount of hot water by setting up the power facility as the welled-out amount has decreased. Major point of recent administration on the hot spring is to permit excavation and utilization of hot springs. Designation of National hot spring health resorts started in 1954 in order to ensure the effective and original use of hot springs and to promote the public use of them, for the purpose of arranging the sound circumstances of hot springs. By 1988, 76 places were designated. 4 figs., 3 tabs.

Spring security 3.x cookbook

CERN Document Server

Mankale, Anjana

2013-01-01

This book follows a cookbook style exploring various security solutions provided by Spring Security for various vulnerabilities and threat scenarios that web applications may be exposed to at the authentication and session level layers.This book is for all Spring-based application developers as well as Java web developers who wish to implement robust security mechanisms into web application development using Spring Security.Readers are assumed to have a working knowledge of Java web application development, a basic understanding of the Spring framework, and some knowledge of the fundamentals o

Geochemical and hydrologic data for wells and springs in thermal-spring areas of the Appalachians

Energy Technology Data Exchange (ETDEWEB)

Hobba, W.A. Jr.; Chemerys, J.C.; Fisher, D.W.; Pearson, F.J. Jr.

1976-07-01

Current interest in geothermal potential of thermal-spring areas in the Appalachians makes all data on thermal springs and wells in these areas valuable. Presented here without interpretive comment are maps showing selected springs and wells and tables of physical and chemical data pertaining to these wells and springs. The chemical tables show compositions of gases (oxygen, nitrogen, argon, methane, carbon dioxide, and helium), isotope contents (tritium, carbon (13), and oxygen (18)), trace and minor element chemical data, and the usual complete chemical data.

Applying spatial analysis techniques to assess the suitability of multipurpose uses of spring water in the Jiaosi Hot Spring Region, Taiwan

Science.gov (United States)

Jang, Cheng-Shin

2016-04-01

The Jiaosi Hot Spring Region is located in northeastern Taiwan and is rich in geothermal springs. The geothermal development of the Jiaosi Hot Spring Region dates back to the 18th century and currently, the spring water is processed for various uses, including irrigation, aquaculture, swimming, bathing, foot spas, and recreational tourism. Because of the proximity of the Jiaosi Hot Spring Region to the metropolitan area of Taipei City, the hot spring resources in this region attract millions of tourists annually. Recently, the Taiwan government is paying more attention to surveying the spring water temperatures in the Jiaosi Hot Spring Region because of the severe spring water overexploitation, causing a significant decline in spring water temperatures. Furthermore, the temperature of spring water is a reliable indicator for exploring the occurrence and evolution of springs and strongly affects hydrochemical reactions, components, and magnitudes. The multipurpose uses of spring water can be dictated by the temperature of the water. Therefore, accurately estimating the temperature distribution of the spring water is critical in the Jiaosi Hot Spring Region to facilitate the sustainable development and management of the multipurpose uses of the hot spring resources. To evaluate the suitability of spring water for these various uses, this study spatially characterized the spring water temperatures of the Jiaosi Hot Spring Region by using ordinary kriging (OK), sequential Gaussian simulation (SGS), and geographical information system (GIS). First, variogram analyses were used to determine the spatial variability of spring water temperatures. Next, OK and SGS were adopted to model the spatial distributions and uncertainty of the spring water temperatures. Finally, the land use (i.e., agriculture, dwelling, public land, and recreation) was determined and combined with the estimated distributions of the spring water temperatures using GIS. A suitable development strategy

Spring Recipes A Problem-solution Approach

CERN Document Server

Long, Josh; Mak, Gary

2010-01-01

With over 3 Million users/developers, Spring Framework is the leading "out of the box" Java framework. Spring addresses and offers simple solutions for most aspects of your Java/Java EE application development, and guides you to use industry best practices to design and implement your applications. The release of Spring Framework 3 has ushered in many improvements and new features. Spring Recipes: A Problem-Solution Approach, Second Edition continues upon the bestselling success of the previous edition but focuses on the latest Spring 3 features for building enterprise Java applications.

Quarry geotechnical report for the Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1990-11-01

This report has been prepared for the United States Department of Energy's (DOE) Weldon Spring Site Remedial Action Project (WSSRAP) by the Project Management Contractor (PMC), which is MK-Ferguson Company (MK-Ferguson) with Jacobs Engineering Group (JEG) as its designated subcontractor. The Weldon Spring site (WSS) comprises the Weldon Spring quarry area and the Weldon Spring chemical plant and raffinate pit areas. This report presents the results of geotechnical investigations conducted during 1989--1990 at the proposed Weldon Spring quarry staging and water treatment facilities in the quarry area. The facilities are intended for treatment of water removed from the quarry area. An access road and a decontamination pad will be necessary for handling and transportation of bulk waste. Results of previous geotechnical investigations performed by other geoscience and environmental engineering firms in the quarry area, were reviewed, summarized and incorporated into this report. Well logging, stratigraphy data, piezometer data, elevations, and soil characteristics are also included

Spring/dimple instrument tube restraint

International Nuclear Information System (INIS)

DeMario, E.E.; Lawson, C.N.

1993-01-01

A nuclear fuel assembly for a pressurized water nuclear reactor has a spring and dimple structure formed in a non-radioactive insert tube placed in the top of a sensor receiving instrumentation tube thimble disposed in the fuel assembly and attached at a top nozzle, a bottom nozzle, and intermediate grids. The instrumentation tube thimble is open at the top, where the sensor or its connection extends through the cooling water for coupling to a sensor signal processor. The spring and dimple insert tube is mounted within the instrumentation tube thimble and extends downwardly adjacent the top. The springs and dimples restrain the sensor and its connections against lateral displacement causing impact with the instrumentation tube thimble due to the strong axial flow of cooling water. The instrumentation tube has a stainless steel outer sleeve and a zirconium alloy inner sleeve below the insert tube adjacent the top. The insert tube is relatively non-radioactivated inconel alloy. The opposed springs and dimples are formed on diametrically opposite inner walls of the insert tube, the springs being formed as spaced axial cuts in the insert tube, with a web of the insert tube between the cuts bowed radially inwardly for forming the spring, and the dimples being formed as radially inward protrusions opposed to the springs. 7 figures

Canine distemper virus infection in a lesser grison (Galictis cuja: first report and virus phylogeny Infecção pelo vírus da cinomose canina em um furão (Galictis cuja: primeiro relato e filogenia viral

Directory of Open Access Journals (Sweden)

Jane Megid

2013-02-01

Full Text Available Infectious diseases in wild animals have been increasing as a result of their habitat alterations and closer contact with domestic animals. Canine distemper virus (CDV has been reported in several species of wild carnivores, presenting a threat to wildlife conservation. We described the first case of canine distemper virus infection in lesser grison (Galictis cuja. A free-ranging individual, with no visible clinical sigs, presented sudden death after one day in captivity. Molecular diagnosis for CDV infection was performed using whole blood collected by postmortem intracardiac puncture, which resulted positive. The virus phylogeny indicated that domestic dogs were the probable source of infection.Doenças infecciosas em animais selvagens têm aumentado devido às alterações em seu habitat e ao maior contato com animais domésticos. A cinomose já foi descrita em diversas espécies de carnívoros selvagens, representando uma ameaça à conservação da vida selvagem. Nesse estudo é descrito o primeiro caso de infecção pelo vírus da cinomose em um furão (Galictis cuja. Um indivíduo de vida livre, sem sinais clínicos aparentes, apresentou morte súbita após um dia em cativeiro. Foi realizado o diagnóstico molecular para detecção do vírus da cinomose canina, sendo o resultado positivo. A filogenia do vírus indicou que cães domésticos foram a provável fonte de infecção.

[History of hot spring bath treatment in China].

Science.gov (United States)

Hao, Wanpeng; Wang, Xiaojun; Xiang, Yinghong; Gu Li, A Man; Li, Ming; Zhang, Xin

2011-07-01

As early as the 7th century B.C. (Western Zhou Dynasty), there is a recording as 'spring which contains sulfur could treat disease' on the Wentang Stele written by WANG Bao. Wenquan Fu written by ZHANG Heng in the Easten Han Dynasty also mentioned hot spring bath treatment. The distribution of hot springs in China has been summarized by LI Daoyuan in the Northern Wei Dynasty in his Shuijingzhu which recorded hot springs in 41 places and interpreted the definition of hot spring. Bencao Shiyi (by CHEN Cangqi, Tang Dynasty) discussed the formation of and indications for hot springs. HU Zai in the Song Dynasty pointed out distinguishing hot springs according to water quality in his book Yuyin Conghua. TANG Shenwei in the Song Dynasty noted in Jingshi Zhenglei Beiji Bencao that hot spring bath treatment should be combined with diet. Shiwu Bencao (Ming Dynasty) classified hot springs into sulfur springs, arsenicum springs, cinnabar springs, aluminite springs, etc. and pointed out their individual indications. Geologists did not start the work on distribution and water quality analysis of hot springs until the first half of the 20th century. There are 972 hot springs in Wenquan Jiyao (written by geologist ZHANG Hongzhao and published in 1956). In July 1982, the First National Geothermal Conference was held and it reported that there were more than 2600 hot springs in China. Since the second half of the 20th century, hot spring sanatoriums and rehabilitation centers have been established, which promoted the development of hot spring bath treatment.

Nuclear reactor spring strip grid spacer

International Nuclear Information System (INIS)

Patterson, J.F.; Flora, B.S.

1978-01-01

A bimetallic grid spacer is described comprising a grid structure of zircaloy formed by intersecting striplike members which define fuel element openings for receiving fuel elements and spring strips made of Inconel positioned within the grid structure for cooperating with the fuel elements to maintain them in their desired position. A plurality of these spring strips extend longitudinally between sides of the grid structure, being locked in position by the grid retaining strips. The fuel rods, which are disposed in the fuel openings formed in the grid structure, are positioned by means of the springs associated with the spring strips and a plurality of dimples which extend from the zircaloy grid structure into the openings. In one embodiment the strips are disposed in a plurality of arrays with those spring strip arrays situated in opposing diagonal quadrants of the grid structure extending in the same direction and adjacent spring strip arrays in each half of the spacer extending in relatively perpendicular directions. Other variations of the spring strip arrangements for a particular fuel design are disclosed herein

75 FR 39241 - Hooper Springs Project

Science.gov (United States)

2010-07-08

... DEPARTMENT OF ENERGY Bonneville Power Administration Hooper Springs Project AGENCY: Bonneville... (collectively referred to as the Hooper Springs Project). The new BPA substation would be called Hooper Springs... proposed project would address voltage stability and reliability concerns of two of BPA's full requirements...

Developing bulk exchange spring magnets

Science.gov (United States)

Mccall, Scott K.; Kuntz, Joshua D.

2017-06-27

A method of making a bulk exchange spring magnet by providing a magnetically soft material, providing a hard magnetic material, and producing a composite of said magnetically soft material and said hard magnetic material to make the bulk exchange spring magnet. The step of producing a composite of magnetically soft material and hard magnetic material is accomplished by electrophoretic deposition of the magnetically soft material and the hard magnetic material to make the bulk exchange spring magnet.

Vibro-spring particle size distribution analyser

International Nuclear Information System (INIS)

Patel, Ketan Shantilal

2002-01-01

This thesis describes the design and development of an automated pre-production particle size distribution analyser for particles in the 20 - 2000 μm size range. This work is follow up to the vibro-spring particle sizer reported by Shaeri. In its most basic form, the instrument comprises a horizontally held closed coil helical spring that is partly filled with the test powder and sinusoidally vibrated in the transverse direction. Particle size distribution data are obtained by stretching the spring to known lengths and measuring the mass of the powder discharged from the spring's coils. The size of the particles on the other hand is determined from the spring 'intercoil' distance. The instrument developed by Shaeri had limited use due to its inability to measure sample mass directly. For the device reported here, modifications are made to the original configurations to establish means of direct sample mass measurement. The feasibility of techniques for measuring the mass of powder retained within the spring are investigated in detail. Initially, the measurement of mass is executed in-situ from the vibration characteristics based on the spring's first harmonic resonant frequency. This method is often erratic and unreliable due to the particle-particle-spring wall interactions and the spring bending. An much more successful alternative is found from a more complicated arrangement in which the spring forms part of a stiff cantilever system pivoted along its main axis. Here, the sample mass is determined in the 'static mode' by monitoring the cantilever beam's deflection following the wanton termination of vibration. The system performance has been optimised through the variations of the mechanical design of the key components and the operating procedure as well as taking into account the effect of changes in the ambient temperature on the system's response. The thesis also describes the design and development of the ancillary mechanisms. These include the pneumatic

Force delivery of Ni-Ti coil springs.

Science.gov (United States)

Manhartsberger, C; Seidenbusch, W

1996-01-01

Sentalloy springs (GAC, Central Islip, N.Y.) of the open and closed type were investigated with a special designed device. The closed coil springs were subjected to a tensile and the open coil springs to a compression test. After a first measurement, the springs were activated for a period of 4 weeks and then reinvestigated with the same procedure. It could be shown distinctly that, with the different coil springs, the force delivery given by the producer could be achieved only within certain limits. To remain in the martensitic plateau, changed activation ranges, and for the Sentalloy coil springs white and red of the open and closed type, also changed force deliveries had to be taken into account. There was a distinct decrease in force delivery between the first and second measurement. After considering the loading curves of all the Sentalloy coil springs and choosing the right activation range respective to the force delivery, it was found that the coil springs deliver a superior clinical behavior and open new treatment possibilities.

Flow-induced vibration of helical coil compression springs

International Nuclear Information System (INIS)

Stokes, F.E.; King, R.A.

1983-01-01

Helical coil compression springs are used in some nuclear fuel assembly designs to maintain holddown and to accommodate thermal expansion. In the reactor environment, the springs are exposed to flowing water, elevated temperatures and pressures, and irradiation. Flow parallel to the longitudinal axis of the spring may excite the spring coils and cause vibration. The purpose of this investigation was to determine the flow-induced vibration (FIV) response characteristics of the helical coil compression springs. Experimental tests indicate that a helical coil spring responds like a single circular cylinder in cross-flow. Two FIV excitation mechanisms control spring vibration. Namely: 1) Turbulent Buffeting causes small amplitude vibration which increases as a function of velocity squared. 2) Vortex Shedding causes large amplitude vibration when the spring natural frequency and Strouhal frequency coincide. Several methods can be used to reduce or to prevent vortex shedding large amplitude vibrations. One method is compressing the spring to a coil pitch-to-diameter ratio of 2 thereby suppressing the vibration amplitude. Another involves modifying the spring geometry to alter its stiffness and frequency characteristics. These changes result in separation of the natural and Strouhal frequencies. With an understanding of how springs respond in the flowing water environment, the spring physical parameters can be designed to avoid large amplitude vibration. (orig.)

Marble Canyon spring sampling investigation

International Nuclear Information System (INIS)

McCulley, B.

1985-10-01

The Mississippian Leadville Limestone is the most permeable formation in the lower hydrostratigraphic unit underlying the salt beds of the Paradox Formation in Gibson Dome, Paradox Basin, Utah, which is being considered as a potential nuclear waste repository site. The closest downgradient outcrop of the Mississippian limestone is along the Colorado River in Marble Canyon, Arizona. This report describes the sampling and interpretation of springs in that area to assess the relative contribution of Gibson Dome-type Leadville Limestone ground water to that spring discharge. The high-volume (hundreds of liters per second or thousands of gallons per minute) springs discharging from fault zones in Marble Canyon are mixtures of water recharged west of the Colorado River on the Kaibab Plateau and east of the river in the Kaiparowits basin. No component of Gibson Dome-type Leadville Limestone ground water is evident in major and trace element chemistry or isotopic composition of the Marble Canyon Springs. A low-volume (0.3 liters per second or 5 gallons per minute) spring with some chemical and isotopic characteristics of Gibson Dome-type Leadville Limestone water diluted by Kaiparowits basin-type water issues from a travertine mound in the Bright Angel Shale on the Little Colorado River. However, the stable isotopic composition and bromide levels of that spring discharge, in addition to probable ground-water flow paths, contradict the dilution hypothesis

Open-Coil Retraction Spring

Directory of Open Access Journals (Sweden)

Pavankumar Janardan Vibhute

2011-01-01

Full Text Available Sliding mechanic has become a popular method for space closure with developments in preadjusted edgewise appliance. Furthermore, various space closing auxiliaries have been developed and evaluated extensively for their clinical efficiency. Their effectiveness enhanced with optimum force magnitude and low-load deflection rate (LDR/force decay. With the advent of NiTi springs in orthodontics, LDRs have been markedly reduced. For use of NiTi, clinician has to depend upon prefabricated closed coil springs. “Open Coil Retraction Spring (OCRS” is developed utilizing NiTi open-coil spring for orthodontic space closure. This paper describes fabrication and clinical application of OCRS which have number of advantages. It sustains low LDR with optimum force magnitude. Its design is adjustable for desired length and force level. It is fail-safe for both activation and deactivation (i.e., it cannot be over activated, and decompression limit of open coil is also controlled by the operator, resp.. A possibility to offset the OCRS away from mucosa helps to reduce its soft-tissue impingement.

Outer grid strap protruding spring repair apparatus

International Nuclear Information System (INIS)

Widener, W.H.

1987-01-01

This patent describes a nuclear fuel assembly grid spring repair apparatus for repairing a spring formed on an outer strap of a fuel assembly grid and having a portion protruding outwardly beyond the strap, the apparatus comprising: (a) a support frame defining an opening and having means defining a guide channel extending along the opening in a first direction; (b) means mounted on the frame and being adjustable for attaching the frame to the outer strap of the support grid so that the frame opening is aligned with the outwardly protruding spring on the outer strap; (c) an outer slide having a passageway defined therethrough and being mounted in the guide channel for reciprocable movement along the frame opening in the first direction for aligning the passageway with the outwardly protruding portion of the spring on the outer strap. The outer slide also has means defining a guide way extending along the passageway in a second direction generally orthogonal to the first direction; (d) a spring reset mechanism being operable for resetting the protruding spring to a nonprotruding position relative to the outer strap when the mechanism is aligned with the protruding portion of the spring; and (e) an inner slide supporting the spring reset mechanism and being mounted to the guide way for reciprocable movement along the passageway of the outer slide in the second direction for aligning the spring reset mechanism with the protruding portion of the spring on the outer strap

Prediction of Spring Rate and Initial Failure Load due to Material Properties of Composite Leaf Spring

International Nuclear Information System (INIS)

Oh, Sung Ha; Choi, Bok Lok

2014-01-01

This paper presented analysis methods for adapting E-glass fiber/epoxy composite (GFRP) materials to an automotive leaf spring. It focused on the static behaviors of the leaf spring due to the material composition and its fiber orientation. The material properties of the GFRP composite were directly measured based on the ASTM standard test. A reverse implementation was performed to obtain the complete set of in-situ fiber and matrix properties from the ply test results. Next, the spring rates of the composite leaf spring were examined according to the variation of material parameters such as the fiber angles and resin contents of the composite material. Finally, progressive failure analysis was conducted to identify the initial failure load by means of an elastic stress analysis and specific damage criteria. As a result, it was found that damage first occurred along the edge of the leaf spring owing to the shear stresses

Pro Spring security

CERN Document Server

Scarioni, Carlo

2013-01-01

Security is a key element in the development of any non-trivial application. The Spring Security Framework provides a comprehensive set of functionalities to implement industry-standard authentication and authorization mechanisms for Java applications. Pro Spring Security will be a reference and advanced tutorial that will do the following: Guides you through the implementation of the security features for a Java web application by presenting consistent examples built from the ground-up. Demonstrates the different authentication and authorization methods to secure enterprise-level applications

1988 Hanford riverbank springs characterization report

International Nuclear Information System (INIS)

Dirkes, R.L.

1990-12-01

This reports presents the results of a special study undertaken to characterize the riverbank springs (i.e., ground-water seepage) entering the Columbia River along the Hanford Site. Radiological and nonradiological analyses were performed. River water samples were also analyzed from upstream and downstream of the Site as well as from the immediate vicinity of the springs. In addition, irrigation return water and spring water entering the river along the shoreline opposite Hanford were analyzed. Hanford-origin contaminants were detected in spring water entering the Columbia River along the Hanford Site. The type and concentrations of contaminants in the spring water were similar to those known to exist in the ground water near the river. The location and extent of the contaminated discharges compared favorably with recent ground-water reports and predictions. Spring discharge volumes remain very small relative to the flow of the Columbia. Downstream river sampling demonstrates the impact of ground-water discharges to be minimal, and negligible in most cases. Radionuclide concentrations were below US Department of Energy Derived Concentration Guides (DCGs) with the exception 90 Sr near the 100-N Area. Tritium, while below the DCG, was detected at concentrations above the US Environmental Protection Agency drinking water standards in several springs. All other radionuclide concentrations were below drinking water standards. Nonradiological contaminants were generally undetectable in the spring water. River water contaminant concentrations, outside of the immediate discharge zones, were below drinking water standards in all cases. 19 refs., 5 figs., 12 tabs

A springs actuated finger exoskeleton: From mechanical design to spring variables evaluation.

Science.gov (United States)

Bortoletto, Roberto; Mello, Ashley N; Piovesan, Davide

2017-07-01

In the context of post-stroke patients, suffering of hemiparesis of the hand, robot-aided neuro-motor rehabilitation allows for intensive rehabilitation treatments and quantitative evaluation of patients' progresses. This work presents the design and evaluation of a spring actuated finger exoskeleton. In particular, the spring variables and the interaction forces between the assembly and the hand were investigated, in order to assess the effectiveness of the proposed exoskeleton.

Portrait of a Geothermal Spring, Hunter's Hot Springs, Oregon.

Science.gov (United States)

Castenholz, Richard W

2015-01-27

Although alkaline Hunter's Hot Springs in southeastern Oregon has been studied extensively for over 40 years, most of these studies and the subsequent publications were before the advent of molecular methods. However, there are many field observations and laboratory experiments that reveal the major aspects of the phototrophic species composition within various physical and chemical gradients of these springs. Relatively constant temperature boundaries demark the upper boundary of the unicellular cyanobacterium, Synechococcus at 73-74 °C (the world-wide upper limit for photosynthesis), and 68-70 °C the upper limit for Chloroflexus. The upper limit for the cover of the filamentous cyanobacterium, Geitlerinema (Oscillatoria) is at 54-55 °C, and the in situ lower limit at 47-48 °C for all three of these phototrophs due to the upper temperature limit for the grazing ostracod, Thermopsis. The in situ upper limit for the cyanobacteria Pleurocapsa and Calothrix is at ~47-48 °C, which are more grazer-resistant and grazer dependent. All of these demarcations are easily visible in the field. In addition, there is a biosulfide production in some sections of the springs that have a large impact on the microbiology. Most of the temperature and chemical limits have been explained by field and laboratory experiments.

Soft tissue modelling with conical springs.

Science.gov (United States)

Omar, Nadzeri; Zhong, Yongmin; Jazar, Reza N; Subic, Aleksandar; Smith, Julian; Shirinzadeh, Bijan

2015-01-01

This paper presents a new method for real-time modelling soft tissue deformation. It improves the traditional mass-spring model with conical springs to deal with nonlinear mechanical behaviours of soft tissues. A conical spring model is developed to predict soft tissue deformation with reference to deformation patterns. The model parameters are formulated according to tissue deformation patterns and the nonlinear behaviours of soft tissues are modelled with the stiffness variation of conical spring. Experimental results show that the proposed method can describe different tissue deformation patterns using one single equation and also exhibit the typical mechanical behaviours of soft tissues.

Isolators Including Main Spring Linear Guide Systems

Science.gov (United States)

Goold, Ryan (Inventor); Buchele, Paul (Inventor); Hindle, Timothy (Inventor); Ruebsamen, Dale Thomas (Inventor)

2017-01-01

Embodiments of isolators, such as three parameter isolators, including a main spring linear guide system are provided. In one embodiment, the isolator includes first and second opposing end portions, a main spring mechanically coupled between the first and second end portions, and a linear guide system extending from the first end portion, across the main spring, and toward the second end portion. The linear guide system expands and contracts in conjunction with deflection of the main spring along the working axis, while restricting displacement and rotation of the main spring along first and second axes orthogonal to the working axis.

Masters of the springs

DEFF Research Database (Denmark)

Laursen, Steffen

2010-01-01

flanked by villages that relied on these water recourses for agricultural production. The springs emerged in the zone separating the cemeteries from the settlements. The freshwater springs were actively incorporated into the religious landscape of the dead, by consistently erecting mounds of a particular...... for water - a process which perhaps also is evidenced by temple constructions at Barbar, Umm al-Sujur and Abu Zaydan....

Optical spring effect in nanoelectromechanical systems

International Nuclear Information System (INIS)

Tian, Feng; Zhou, Guangya; Du, Yu; Chau, Fook Siong; Deng, Jie

2014-01-01

In this Letter, we report a hybrid system consisting of nano-optical and nano-mechanical springs, in which the optical spring effect works to adjust the mechanical frequency of a nanoelectromechanical systems resonator. Nano-scale folded beams are fabricated as the mechanical springs and double-coupled one-dimensional photonic crystal cavities are used to pump the “optical spring.” The dynamic characteristics of this hybrid system are measured and analyzed at both low and high input optical powers. This study leads the physical phenomenon of optomechanics in complex nano-opto-electro-mechanical systems (NOEMS) and could benefit the future applications of NOEMS in chip-level communication and sensing

Fossilization Processes in Thermal Springs

Science.gov (United States)

Farmer, Jack D.; Cady, Sherry; Desmarais, David J.; Chang, Sherwood (Technical Monitor)

1995-01-01

To create a comparative framework for the study of ancient examples, we have been carrying out parallel studies of the microbial biosedimentology, taphonomy and geochemistry of modem and sub-Recent thermal spring deposits. One goal of the research is the development of integrated litho- and taphofacies models for siliceous and travertline sinters. Thermal springs are regarded as important environments for the origin and early evolution of life on Earth, and we seek to utilize information from the fossil record to reconstruct the evolution of high temperature ecosystems. Microbial contributions to the fabric of thermal spring sinters occur when population growth rates keep pace with, or exceed rates of inorganic precipitation, allowing for the development of continuous biofilms or mats. In siliceous thermal springs, microorganisms are typically entombed while viable. Modes of preservation reflect the balance between rates of organic matter degradation, silica precipitation and secondary infilling. Subaerial sinters are initially quite porous and permeable and at temperatures higher than about 20 C, organic materials are usually degraded prior to secondary infilling of sinter frameworks. Thus, organically-preserved microfossils are rare and fossil information consists of characteristic biofabrics formed by the encrustation and underplating of microbial mat surfaces. This probably accounts for the typically low total organic carbon values observed in thermal spring deposits. In mid-temperature, (approx. 35 - 59 C) ponds and outflows, the surface morphology of tufted Phormidium mats is preserved through mat underplating by thin siliceous: crusts. Microbial taxes lead to clumping of ceils and/or preferred filament orientations that together define higher order composite fabrics in thermal spring stromatolites (e.g. network, coniform, and palisade). At lower temperatures (less than 35 C), Calothrix mats cover shallow terracette pools forming flat carpets or pustular

European supply chain for valve springs

Energy Technology Data Exchange (ETDEWEB)

Barthold, G. [Scherdel GmbH, Marktredwitz (Germany); Thureborn, D.; Hallberg, M. [Haldex Garphyttan AB (Sweden); Janssen, P. [Mittal Steel Ruhrort GmbH / Mittal Steel Hochfeld GmbH (Germany)

2005-07-01

Forced by the Kobe earthquake in 1995 and the lack of valve spring steel on the world market due to damages of the Kobe steel plant, the development of a European supply chain has been sped up. End of 1994 a super clean valve spring steel with a reasonable quality from a European source was available. A strong relationship between the steel producer (Mittal), the wire manufacturer (Haldex Garphyttan) and the spring maker (Scherdel) was established. A working group of the three companies holds meetings on a regular basis to discuss quality and development issues. Over the last years the supply chain has achieved significant improvements in terms of cleanliness and decarburisation of the wire rod. The continuous common advancement of the valve spring quality has enabled the valve spring failures in the field to be reduced to < 0.1 ppm. The development and market launch of new grades has been prepared. (orig.)

Characteristics Analysis and Testing of SMA Spring Actuator

Directory of Open Access Journals (Sweden)

Jianzuo Ma

2013-01-01

Full Text Available The biasing form two-way shape memory alloy (SMA actuator composed of SMA spring and steel spring is analyzed. Based on the force equilibrium equation, the relationship between load capacity of SMA spring and geometric parameters is established. In order to obtain the characteristics of SMA spring actuator, the output force and output displacement of SMA spring under different temperatures are analyzed by the theoretical model and the experimental method. Based on the shape memory effect of SMA, the relationship of the SMA spring actuator's output displacement with the temperature, the stress and strain, the material parameters, and the size parameters is established. The results indicate that the trend of theoretical results is basically consistent with the experimental data. The output displacement of SMA spring actuator is increased with the increasing temperature.

Thermal algae in certain radioactive springs in Japan, (3)

International Nuclear Information System (INIS)

Mifune, Masaaki; Hirose, Hiroyuki.

1982-01-01

Shikano Hot Springs are located at five km to the south of Hamamura Station on the Sanin Line in Tottori Prefecture. The water temperature and the pH of the springs are 40.2 - 61.2 0 C, and 7.5 - 7.8, respectively. They belong to simple thermals. Hamamura Hot Springs are located in the neighbourhood of Hamamura Station. The highest radon content of the hot springs is 175.1 x 10 -10 Ci/l, and the great part of the springs belong to radioactive ones. From the viewpoint of the major ionic constituents, they are also classified under weak salt springs, sulfated salt springs, and simple thermals. Regarding the habitates of the algal flora, the water temperature and the pH of the springs are 28.0 - 68.0 0 C, and 6.8 - 7.4, respectively. The thermal algae found by Ikoma and Doi at Hamamura Hot Springs were two species of Cyanophyceae. By the authors, nine species and one variety of Cyanophyceae including Ikoma and Doi's two species were newly found at Shikano and Hamamura Hot Springs. Chlorophyceous alga was not found. The dominant thermal algae of these hot springs were Mastigocladus laminosus, and the other algae which mainly consist of Oscillatoriaceous algae. From these points, it seems that the thermal algae of Shikano and Hamamura Hot Springs belong to the normal type of thermal algae, and they are different from the thermal algae of Ikeda Mineral Springs and Masutomi Hot Springs which belong to strongly radioactive springs. (author)

Thermal springs of Malaysia and their potentialdevelopment

Science.gov (United States)

Rahim Samsudin, Abdul; Hamzah, Umar; Rahman, Rakmi Ab.; Siwar, Chamhuri; Fauzi Mohd. Jani, Mohd; Othman, Redzuan

The study on the potential development of hot springs for the tourism industry in Malaysiawas conducted. Out of the 40 hot springs covered, the study identified 9 hot springs having a high potential for development, 14 having medium potential and the remaining 17 having low or least potential for development. This conclusion was arrived at after considering the technical and economic feasibility of the various hot springs. Technical feasibility criteria includes geological factors, water quality, temperature and flow rate. The economic feasibility criteria considers measures such as accessibility, current and market potentials in terms of visitors, surrounding attractions and existing inventory and facilities available. A geological input indicates that high potential hot springs are located close to or within the granite body and associated with major permeable fault zones. They normally occur at low elevation adjacent to topographic highs. High potential hot springs are also characterised by high water temperature, substantial flowrate and very good water quality which is important for water-body contact activities such as soaking. Economic criteria for high potential hot springs are associated with good accessibility, good market, good surrounding attractions like rural and village setting and well developed facilities and infrastructures.

Spring harvest of corn stover

Energy Technology Data Exchange (ETDEWEB)

Lizotte, P.L. [Laval Univ., Quebec City, PQ (Canada). Dept. des sols et de genie agroalimentaire; Savoie, P. [Agriculture and Agri-Food Canada, Quebec City, PQ (Canada)

2010-07-01

Corn stover is typically left behind in the field after grain harvest. Although part of the stover should remain in the field for soil organic matter renewal and erosion protection, half of the stover could be removed sustainably. This represents about one million t dry matter (DM) of stover per year in the province of Quebec. Stover harvested in the fall is very wet. While there are applications for wet stover, the available markets currently require a dry product. Preliminary measurements have shown that stover left in the field throughout the winter becomes very dry, and a considerable amount would still be harvestable in the spring. In the spring of 2009, corn stover was harvested at 2 sites, each subdivided into 2 parcels. The first parcel was cut and raked in the fall of 2008 (fall parcel), while the second parcel was cut and raked in spring 2009. Fibre from both parcels was baled in the spring 2009. At the first site, a large square baler was used in late April to produce bales measuring 0.8 m x 0.9 m x 1.8 m. On the second site a round baler was used in late May to produce bales of 1.2 m in width by 1.45 m in diameter. On the second site, a small square baler was also used to produce bales of 0.35 m x 0.45 m x 0.60 m (spring cutting only). With the large square baler, an average of 3.9 t DM/ha was harvested equally on the fall parcel and the spring parcel, representing a 48 per cent recovery of biomass based on stover yields.

The Begg's uprighting spring - Revisited.

Science.gov (United States)

Kumar, Vinay; Sundareswaran, Shobha

2015-01-01

Uprighting springs, an integral part of the Begg ligsht wire differential force technique is gaining more and more popularity, as a useful adjunct in contemporary preadjusted edgewise appliance systems as well. It can be used with brackets containing vertical slots for mesiodistal crown uprighting, or as braking auxiliaries providing additional anchorage while protracting posteriors. Here, we present a simple and quick chair side method of fabricating and customizing uprighting springs according to the required crown/root movement for correction. This communication would serve as a ready reckoner during fabrication of the springs, thus dispelling the confusion that usually arises regarding direction and position of the coil and active arm.

Nickel titanium springs versus stainless steel springs: A randomized clinical trial of two methods of space closure.

Science.gov (United States)

Norman, Noraina Hafizan; Worthington, Helen; Chadwick, Stephen Mark

2016-09-01

To compare the clinical performance of nickel titanium (NiTi) versus stainless steel (SS) springs during orthodontic space closure. Two-centre parallel group randomized clinical trial. Orthodontic Department University of Manchester Dental Hospital and Orthodontic Department Countess of Chester Hospital, United Kingdom. Forty orthodontic patients requiring fixed appliance treatment were enrolled, each being randomly allocated into either NiTi (n = 19) or SS groups (n = 21). Study models were constructed at the start of the space closure phase (T0) and following the completion of space closure (T1). The rate of space closure achieved for each patient was calculated by taking an average measurement from the tip of the canine to the mesiobuccal groove on the first permanent molar of each quadrant. The study was terminated early due to time constraints. Only 30 patients completed, 15 in each study group. There was no statistically significant difference between the amounts of space closed (mean difference 0.17 mm (95%CI -0.99 to 1.34; P = 0.76)). The mean rate of space closure for NiTi coil springs was 0.58 mm/4 weeks (SD 0.24) and 0.85 mm/4 weeks (SD 0.36) for the stainless steel springs. There was a statistically significant difference between the two groups (P = 0.024), in favour of the stainless steel springs, when the mean values per patient were compared. Our study shows that stainless steel springs are clinically effective; these springs produce as much space closure as their more expensive rivals, the NiTi springs.

Experimenting with Inexpensive Plastic Springs

Science.gov (United States)

Perez, Leander; Marques, Adriana; Sánchez, Iván

2014-01-01

Acommon undergraduate laboratory experience is the determination of the elastic constant of a spring, whether studying the elongation under a static load or studying the damped harmonic motion of the spring with a suspended mass. An alternative approach to this laboratory experience has been suggested by Menezes et al., aimed at studying the…

Comparison of gas spring designs with adjustable spring characteristic for a free-piston engine; Vergleich von Gasfedervarianten mit variabler Kennlinie fuer einen Freikolbenmotor

Energy Technology Data Exchange (ETDEWEB)

Pohl, S.E.; Ferrari, C. [Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), Stuttgart (Germany). Inst. fuer Fahrzeugkonzepte

2007-12-15

In this paper two different gas spring designs for a free-piston application are introduced. On the basis of thermodynamic calculations the spring characteristics of a mass-variable and a volume-variable gas spring are analyzed for different operating points. A comparison of the spring performances indicates that the spring characteristics of the two designs only match at one operation point. Therefore, a calculation method minimizing the difference between the two spring characteristics over the entire operating range of a free piston engine is introduced. The theoretical examination is confirmed by measurements on a gas spring test stand. (orig.)

Dissolved oxygen fluctuations in karst spring flow and implications for endemic species: Barton Springs, Edwards aquifer, Texas, USA

Science.gov (United States)

Mahler, Barbara J.; Bourgeais, Renan

2013-01-01

Karst aquifers and springs provide the dissolved oxygen critical for survival of endemic stygophiles worldwide, but little is known about fluctuations of dissolved oxygen concentrations (DO) and factors that control those concentrations. We investigated temporal variation in DO at Barton Springs, Austin, Texas, USA. During 2006–2012, DO fluctuated by as much as a factor of 2, and at some periods decreased to concentrations that adversely affect the Barton Springs salamander (Eurycea sorosum) (≤4.4 mg/L), a federally listed endangered species endemic to Barton Springs. DO was lowest (≤4.4 mg/L) when discharge was low (≤1 m3/s) and spring water temperature was >21 °C, although not at a maximum; the minimum DO recorded was 4.0 mg/L. Relatively low DO (3/s) and maximum T (22.2 °C). A four-segment linear regression model with daily data for discharge and spring water temperature as explanatory variables provided an excellent fit for mean daily DO (Nash–Sutcliffe coefficient for the validation period of 0.90). DO also fluctuated at short-term timescales in response to storms, and DO measured at 15-min intervals could be simulated with a combination of discharge, spring temperature, and specific conductance as explanatory variables. On the basis of the daily-data regression model, we hypothesize that more frequent low DO corresponding to salamander mortality could result from (i) lower discharge from Barton Springs resulting from increased groundwater withdrawals or decreased recharge as a result of climate change, and (or) (ii) higher groundwater temperature as a result of climate change.

Hydrochemical Characteristics of Springs in Oke–Igbo, Ondo State ...

African Journals Online (AJOL)

Michael Horsfall

each spring and analyzed for temperature, pH, electrical conductivity (EC), total dissolved solids (TDS), total ... Boiling of the spring water, is therefore, .... spring against sudden change in pH might also .... The altitude of the springs may have.

Shallow groundwater investigations at Weldon Spring, Missouri

International Nuclear Information System (INIS)

1991-06-01

The Missouri Department of Natural Resources, Division of Geology and Land Survey (MDNR-DGLS) conducted investigations of the upper aquifer in the vicinity of the abandoned Weldon Spring Chemical Plant in southwest St. Charles County, Missouri. The objective of the investigation was to better define the relationships between precipitation, surface runoff, groundwater recharge and shallow groundwater discharge within the study area, thereby assisting the Department of Energy in designing an appropriate groundwater monitoring plan for the Weldon Spring Site Remedial Action Project. The results of the investigations indicate that the upper aquifer has been affected by karst development but that well developed karst does not exist on or around the site. Dye traces conducted during the study have shown that surface water which leaves the site enters the subsurface in losing streams around the site and travels rapidly to one or more local springs. Upper aquifer recharge areas, constructed from dye trace and potentiometric data, generally follow surface water drainage patterns on the south side of the site, but cross surface-water drainage divides north of the site. Nine springs may receive recharge from site runoff, depending upon the amount of runoff. In addition to these springs, one perennial spring and two intermittent springs to the southwest of the site may receive recharge from site infiltration. 25 refs., 13 figs

Sampling and analysis of 100 Area springs

International Nuclear Information System (INIS)

1992-02-01

This report is submitted in fulfillment of Hanford Federal Facility Agreement and Consent Order Milestone M-30-01, submit a report to EPA and Ecology evaluating the impact to the Columbia River from contaminated springs and seeps as described in the operable unit work plans listed in M-30-03. Springs, seeps, sediments, and the Columbia River were sampled for chemical and radiological analyses during the period September 16 through October 21, 1991. A total of 26 locations were sampled. Results of these analyses show that radiological and nonradiological contaminants continue to enter the Columbia River from the retired reactor areas of the 100 Area via the springs. The primary contaminants in the springs are strontium-90, tritium, and chromium. These contaminants were detected in concentrations above drinking water standards. Analysis of total organic carbon were run on all water samples collected; there is no conclusive evidence that organic constituents are entering the river through the springs. Total organic carbon analyses were generally higher for the surface water than for the springs. The results of this study will be used to develop a focused, yet flexible, long-term spring sampling program. Analysis of Columbia River water samples collected at the Hanford Townsite (i.e., downstream of the reactor areas) did not detect any Hanford-specific contaminants

Integrated geophysical investigations of Main Barton Springs, Austin, Texas, USA

Science.gov (United States)

Saribudak, By Mustafa; Hauwert, Nico M.

2017-03-01

Barton Springs is a major discharge site for the Barton Springs Segment of the Edwards Aquifer and is located in Zilker Park, Austin, Texas. Barton Springs actually consists of at least four springs. The Main Barton Springs discharges into the Barton Springs pool from the Barton Springs fault and several outlets along a fault, from a cave, several fissures, and gravel-filled solution cavities on the floor of the pool west of the fault. Surface geophysical surveys [resistivity imaging, induced polarization (IP), self-potential (SP), seismic refraction, and ground penetrating radar (GPR)] were performed across the Barton Springs fault and at the vicinity of the Main Barton Springs in south Zilker Park. The purpose of the surveys was two-fold: 1) locate the precise location of submerged conduits (caves, voids) carrying flow to Main Barton Springs; and 2) characterize the geophysical signatures of the fault crossing Barton Springs pool. Geophysical results indicate significant anomalies to the south of the Barton Springs pool. A majority of these anomalies indicate a fault-like pattern, in front of the south entrance to the swimming pool. In addition, resistivity and SP results, in particular, suggest the presence of a large conduit in the southern part of Barton Springs pool. The groundwater flow-path to the Main Barton Springs could follow the locations of those resistivity and SP anomalies along the newly discovered fault, instead of along the Barton Springs fault, as previously thought.

Portrait of a Geothermal Spring, Hunter’s Hot Springs, Oregon

Directory of Open Access Journals (Sweden)

Richard W. Castenholz

2015-01-01

Full Text Available Although alkaline Hunter’s Hot Springs in southeastern Oregon has been studied extensively for over 40 years, most of these studies and the subsequent publications were before the advent of molecular methods. However, there are many field observations and laboratory experiments that reveal the major aspects of the phototrophic species composition within various physical and chemical gradients of these springs. Relatively constant temperature boundaries demark the upper boundary of the unicellular cyanobacterium, Synechococcus at 73–74 °C (the world-wide upper limit for photosynthesis, and 68–70 °C the upper limit for Chloroflexus. The upper limit for the cover of the filamentous cyanobacterium, Geitlerinema (Oscillatoria is at 54–55 °C, and the in situ lower limit at 47–48 °C for all three of these phototrophs due to the upper temperature limit for the grazing ostracod, Thermopsis. The in situ upper limit for the cyanobacteria Pleurocapsa and Calothrix is at ~47–48 °C, which are more grazer-resistant and grazer dependent. All of these demarcations are easily visible in the field. In addition, there is a biosulfide production in some sections of the springs that have a large impact on the microbiology. Most of the temperature and chemical limits have been explained by field and laboratory experiments.

Portrait of a Geothermal Spring, Hunter’s Hot Springs, Oregon

Science.gov (United States)

Castenholz, Richard W.

2015-01-01

Although alkaline Hunter’s Hot Springs in southeastern Oregon has been studied extensively for over 40 years, most of these studies and the subsequent publications were before the advent of molecular methods. However, there are many field observations and laboratory experiments that reveal the major aspects of the phototrophic species composition within various physical and chemical gradients of these springs. Relatively constant temperature boundaries demark the upper boundary of the unicellular cyanobacterium, Synechococcus at 73–74 °C (the world-wide upper limit for photosynthesis), and 68–70 °C the upper limit for Chloroflexus. The upper limit for the cover of the filamentous cyanobacterium, Geitlerinema (Oscillatoria) is at 54–55 °C, and the in situ lower limit at 47–48 °C for all three of these phototrophs due to the upper temperature limit for the grazing ostracod, Thermopsis. The in situ upper limit for the cyanobacteria Pleurocapsa and Calothrix is at ~47–48 °C, which are more grazer-resistant and grazer dependent. All of these demarcations are easily visible in the field. In addition, there is a biosulfide production in some sections of the springs that have a large impact on the microbiology. Most of the temperature and chemical limits have been explained by field and laboratory experiments. PMID:25633225

Spring valve for well completion

Energy Technology Data Exchange (ETDEWEB)

Gorbatov, P T

1966-07-22

A spring-loaded valve for well completion consists of a housing with a spring-loaded closing element. In order to protect the closing element from corrosion which might lower the pressure drop, the closing element is made in the form of a piston. It is tightly connected with sealing elements. The housing has orifices, overlapping the piston in the initial position.

Elliptical Leaf Spring Shock and Vibration Mounts with Enhanced Damping and Energy Dissipation Capabilities Using Lead Spring

Directory of Open Access Journals (Sweden)

Moussa Leblouba

2015-01-01

Full Text Available We present an enhancement to the existing elliptical leaf spring (ELS for improved damping and energy dissipation capabilities. The ELS consists of a high tensile stainless steel elliptical leaf spring with polymer or rubber compound. This device is conceived as a shock and vibration isolator for equipment and lightweight structures. The enhancement to the ELS consists of a lead spring plugged vertically between the leaves (referred to as lead-rubber elliptical leaf spring (LRELS. The lead is shown to produce hysteretic damping under plastic deformations. The LRELS isolator is shown to exhibit nonlinear hysteretic behavior. In both horizontal directions, the LRELS showed symmetrical rate independent behavior but undergoes stiffening behavior under large displacements. However, in the vertical direction, the LRELS behavior is asymmetric, exhibiting softening behavior in compression and stiffening behavior in tension. Mathematical models based on the Bouc-Wen model, describing the hysteretic behavior of the proposed isolator, are developed and numerically calibrated using a series of finite element analyses. The LRELS is found to be effective in the in-plane and vertical directions. The improved damping and energy dissipation of the LRELS is provided from the hysteretic damping of the lead spring.

Spring-recharging in the Himalayas

International Nuclear Information System (INIS)

Joshi, Anil P.

2009-01-01

in the settlement of mountain villages in the Himalayas. In fact, in many places, it was the single factor that determined the location of the villages and naturally rainwater has been the source which recharge the catchments of the springs. Forest cover keeps these catchment areas alive for the slow and constant recharging of the springs. In the recent past due to continuous deforestation, the catchment areas have been drastically reduced. Eventually, these denuded lands were unable to conserve water, which has resulted in the drying-up and dying of many mountain springs. Certainly, this became a major threat to both the natural habitats of the springs, as well as to the survival of the communities. In order to meet the water needs of the villages, the government-development agencies devised a distribution system in which water was diverted from regions with an adequate supply to those deprived of water. This approach to remedy the water shortage brought about significant water conflicts, as the rights to water resources were not well defined. This system also did not adequately address water-management and distribution lines for the water resources

Analytical Technique of Selection of Constructive Parameters Pneumatichydraulic Springs

Directory of Open Access Journals (Sweden)

A. A. Tsipilev

2014-01-01

Full Text Available The article "Technique for Analytical Selection of Design Parameters of Pneumatichydraulic Springs concerns the ride smoothness of high-speed vehicles. Author of article Tsipilev A.A. is an assistant at chair "Multi-purpose Tracked Vehicles and Mobile Robots" of BMSTU. The article represents a synthesis of known information on the springing systems and an analysis of relation between spring design data and running gear. It describes standard units of running gear of vehicle in the context of springing systems. Classification of springing systems is considered. Modernization general policy for existing suspensions and prospects for creation of new ones are given. The article considers a design of various pneumatic-hydraulic springs to be set on domestic tracked vehicles. A developed technique allows us to have elastic characteristics of pneumatic-hydraulic springs of various types using these design data and kinematics of the running gear. The article provides recommendations to calculate characteristics of springing systems. The adequacy analysis of the given technique based on the comparison of real and rated characteristics of the existing suspension is conducted. This article can be useful to the experts dealing with springing systems of wheel and tracked vehicles.

Pressurizer safety valve serviceability enhancement by spring compression stability

Energy Technology Data Exchange (ETDEWEB)

Ratiu, M.D.; Moisidis, N.T. [California Consulting Engineering and Technology (CALCET), San Leandro, California (United States)

2007-07-01

The proactive maintenance of the spring-loaded-self-actuated Pressurizer Safety Valve (PSV) has caused frequent concerns pertaining the spring self actuated reliability due to set point drift, spurious openings, and seat leakage. The exhaustive testing performed on a Crosby PSV model 6M6 has revealed that the principal cause of these malfunctions is the spring compression elastic instability during service. The spring lateral deformations measurements performed validated the analytical shapes for spring compression: symmetrical bending - for coaxial supported ends - restraining any support displacement, and asymmetrical bending induced by the potential misalignment of the supported top end. The source of the spring compression instability appears on the tested Crosby PSV induced by the top end lateral displacement during long term operation. The testing with restrained displacement at the spring top has shown consistent set-point reproducibility, less than +/- 1 per cent. To eliminate the asymmetrical spring buckling, a design review of the PSV is proposed including the guided fixture at the top and the decrease of spring coil slenderness ratio H/D, corresponding to the general analytical elastic stability for the asymmetrical compression. (authors)

Pressurizer safety valve serviceability enhancement by spring compression stability

International Nuclear Information System (INIS)

Ratiu, M.D.; Moisidis, N.T.

2007-01-01

The proactive maintenance of the spring-loaded-self-actuated Pressurizer Safety Valve (PSV) has caused frequent concerns pertaining the spring self actuated reliability due to set point drift, spurious openings, and seat leakage. The exhaustive testing performed on a Crosby PSV model 6M6 has revealed that the principal cause of these malfunctions is the spring compression elastic instability during service. The spring lateral deformations measurements performed validated the analytical shapes for spring compression: symmetrical bending - for coaxial supported ends - restraining any support displacement, and asymmetrical bending induced by the potential misalignment of the supported top end. The source of the spring compression instability appears on the tested Crosby PSV induced by the top end lateral displacement during long term operation. The testing with restrained displacement at the spring top has shown consistent set-point reproducibility, less than +/- 1 per cent. To eliminate the asymmetrical spring buckling, a design review of the PSV is proposed including the guided fixture at the top and the decrease of spring coil slenderness ratio H/D, corresponding to the general analytical elastic stability for the asymmetrical compression. (authors)

Shape modification for decreasing the spring stiffness of double-plate nozzle type spacer grid spring

International Nuclear Information System (INIS)

Lee, K. H.; Kang, H. S.; Song, K. N.; Yun, K. H.; Kim, H. K.

2001-01-01

Nozzle of the double-plated grid plays the role of the spirng to support a fuel rod as well as the coolant path in grid. The nozzle was known to be necessary to reduce the spring stiffness for supporting performance. In this study, the contact analysis between the fuel rod and the newly designed nozzle was performed by ABAQUS computer code to propose the preferable shape in term of spring performance. Two small cut at the upper and lower part of the nozzle appeared to have a minor effect in decreasing the nozzle stiffness. A long slot at the center of the nozzle was turned out not only to decrease the spring constant as desired but also to increase the elastic displacement

Preliminary geothermal investigations at Manley Hot Springs, Alaska

Energy Technology Data Exchange (ETDEWEB)

East, J.

1982-04-01

Manley Hot Springs is one of several hot springs which form a belt extending from the Seward Peninsula to east-central Alaska. All of the hot springs are low-temperature, water-dominated geothermal systems, having formed as the result of circulation of meteoric water along deepseated fractures near or within granitic intrusives. Shallow, thermally disturbed ground at Manley Hot Springs constitutes an area of 1.2 km by 0.6 km along the lower slopes of Bean Ridge on the north side of the Tanana Valley. This area includes 32 springs and seeps and one warm (29.1/sup 0/C) well. The hottest springs range in temperature from 61/sup 0/ to 47/sup 0/C and are presently utilized for space heating and irrigation. This study was designed to characterize the geothermal system present at Manley Hot Springs and delineate likely sites for geothermal drilling. Several surveys were conducted over a grid system which included shallow ground temperature, helium soil gas, mercury soil and resistivity surveys. In addition, a reconnaissance ground temperature survey and water chemistry sampling program was undertaken. The preliminary results, including some preliminary water chemistry, show that shallow hydrothermal activity can be delineated by many of the surveys. Three localities are targeted as likely geothermal well sites, and a model is proposed for the geothermal system at Manley Hot Springs.

The climatic record of the earliest spring in Romania, regarding the south-east part of the country – spring 2016

Directory of Open Access Journals (Sweden)

I. OCTAVIA BOGDAN

2016-11-01

Full Text Available The climatic record of the earliest spring in Romania, regarding the south-east part of the country – Spring 2016. In the past 30 years it has been an increasing frequency of early SPRING ARRIVAL. Therefore, vegetation development started in early February. In March, the warm weather continued almost throughout the month, and the hoarfrosts from March became hereby destructive. Frequently, the vegetation in April was in very advanced stages. Even though the temperatures rose in April, cooling in April and late spring hoarfrosts have occurred and caused considerable damage. In this study we analyze the climatic macroprocesses that led to the apparition of an absolute climate record for the earliest spring arrival in 2016. The work is useful to anyone interested in climate change in Romania.

Manufacture of conical springs with elastic medium technology improvement

Science.gov (United States)

Kurguzov, S. A.; Mikhailova, U. V.; Kalugina, O. B.

2018-01-01

This article considers the manufacturing technology improvement by using an elastic medium in the stamping tool forming space to improve the conical springs performance characteristics and reduce the costs of their production. Estimation technique of disk spring operational properties is developed by mathematical modeling of the compression process during the operation of a spring. A technique for optimizing the design parameters of a conical spring is developed, which ensures a minimum voltage value when operated in the edge of the spring opening.

Stiffness and design for strength of trapezoidal Belleville springs

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard; Pedersen, Pauli

2011-01-01

in this paper. Finite element results are compared with analytical predictions and critically analysed in terms of the effect of Poisson ratio, overall stiffness, and stress distribution in the spring. This is done in order to verify the range of validity of design standards. Finite element analysis emerges......Belleville springs or coned disc springs are commonly used in machine design. The geometric dimensions of the spring and the determination of non-linear force–displacement curve are regulated by different standards. However, the theory behind Belleville spring design standards is founded on a study...... published in 1936. Furthermore, the common spring design with cross-sections of uniform thickness poses problems in terms of non-uniformity of stress distribution. In view of this, non-linear three-dimensional finite element analyses of spring designs including uniform or variable thickness are carried out...

Hydrosalinity studies of the Virgin River, Dixie Hot Springs, and Littlefield Springs, Utah, Arizona, and Nevada

Science.gov (United States)

Gerner, Steven J.; Thiros, Susan A.; Gerner, Steven J.; Thiros, Susan A.

2014-01-01

The Virgin River contributes a substantial amount of dissolved solids (salt) to the Colorado River at Lake Mead in the lower Colorado River Basin. Degradation of Colorado River water by the addition of dissolved solids from the Virgin River affects the suitability of the water for municipal, industrial, and agricultural use within the basin. Dixie Hot Springs in Utah are a major localized source of dissolved solids discharging to the Virgin River. The average measured discharge from Dixie Hot Springs during 2009–10 was 11.0 cubic feet per second (ft3/s), and the average dissolved-solids concentration was 9,220 milligrams per liter (mg/L). The average dissolved-solids load—a measurement that describes the mass of salt that is transported per unit of time—from Dixie Hot Springs during this period was 96,200 tons per year (ton/yr). Annual dissolved-solids loads were estimated at 13 monitoring sites in the Virgin River Basin from streamflow data and discrete measurements of dissolved-solids concentrations and (or) specific conductance. Eight of the sites had the data needed to estimate annual dissolved-solids loads for water years (WYs) 1999 through 2010. During 1999–2010, the smallest dissolved-solids loads in the Virgin River were upstream of Dixie Hot Springs (59,900 ton/yr, on average) and the largest loads were downstream of Littlefield Springs (298,200 ton/yr, on average). Annual dissolved-solids loads were smallest during 2002–03, which was a period of below normal precipitation. Annual dissolved-solids loads were largest during 2005—a year that included a winter rain storm that resulted in flooding throughout much of the Virgin River Basin. An average seepage loss of 26.7 ft3/s was calculated from analysis of monthly average streamflow from July 1998 to September 2010 in the Virgin River for the reach that extends from just upstream of the Utah/Arizona State line to just above the Virgin River Gorge Narrows. Seepage losses from three river reaches

Top Nozzle Holddown Spring Optimization of KSNP Fuel Assembly

International Nuclear Information System (INIS)

Lee, Seong Ki; Park, Nam Kyu; Kim, Hyeong Koo; Lee, Joon Ro; Kim, Jae Won

2002-01-01

Nuclear fuel assembly for Korea Standard Nuclear Power (KSNP) Plant has 4 helical compression springs at the upper end of it. The springs, in conjunction with the fuel assembly weight, apply a holddown force against excess of buoyancy forces and the upward hydraulic forces due to the reactor coolant flow. Thus the holddown spring is to be designed such that the positive net downward force will be maintained for all normal and anticipated transient flow and temperature conditions in the nuclear reactor. With satisfying these in-reactor requirements of the fuel assembly holddown spring. Under the assumption that spring density is constant, the volume nozzle holddown spring. Under the assumption that spring density is constant, the volume minimization is executed by using the design variables, viz., wire diameter, mean coil diameter, minimization is executed by using the design variables, viz., wire diameter, mean coil diameter are within the compatible range of the fuel assembly structural components. Based on these conditions, the optimum design of the holddown spring is obtained considering the reactor operating condition and by using ANSYS code. The optimized spring has the properties that are a decreased volume and increased stiffness, compared with the existing one even if the absolute values are very similar each other. The holddown spring design features and the algorithm developed in this study could be directly applicable to the current commercial production. Therefore, it could be used to enhance the design efficiency and the functional performance of the spring, and to reduce a material cost a little

Geochemistry and hydrology of perched groundwater springs: assessing elevated uranium concentrations at Pigeon Spring relative to nearby Pigeon Mine, Arizona (USA)

Science.gov (United States)

Beisner, Kimberly R.; Paretti, Nicholas; Tillman, Fred; Naftz, David L.; Bills, Donald; Walton-Day, Katie; Gallegos, Tanya J.

2017-01-01

The processes that affect water chemistry as the water flows from recharge areas through breccia-pipe uranium deposits in the Grand Canyon region of the southwestern United States are not well understood. Pigeon Spring had elevated uranium in 1982 (44 μg/L), compared to other perched springs (2.7–18 μg/L), prior to mining operations at the nearby Pigeon Mine. Perched groundwater springs in an area around the Pigeon Mine were sampled between 2009 and 2015 and compared with material from the Pigeon Mine to better understand the geochemistry and hydrology of the area. Two general groups of perched groundwater springs were identified from this study; one group is characterized by calcium sulfate type water, low uranium activity ratio 234U/238U (UAR) values, and a mixture of water with some component of modern water, and the other group by calcium-magnesium sulfate type water, higher UAR values, and radiocarbon ages indicating recharge on the order of several thousand years ago. Multivariate statistical principal components analysis of Pigeon Mine and spring samples indicate Cu, Pb, As, Mn, and Cd concentrations distinguished mining-related leachates from perched groundwater springs. The groundwater potentiometric surface indicates that perched groundwater at Pigeon Mine would likely flow toward the northwest away from Pigeon Spring. The geochemical analysis of the water, sediment and rock samples collected from the Snake Gulch area indicate that the elevated uranium at Pigeon Spring is likely related to a natural source of uranium upgradient from the spring and not likely related to the Pigeon Mine.

Wolfcampian brachiopods from the Bird Spring Group, Wamp Spring area, Las Vegas Range, Clark County, Nevada ( USA).

Science.gov (United States)

Mills, P.C.; Langenheim, R.L.

1987-01-01

The Wamp Spring section of the Bird Spring Group is subdivided into a basal platy limestone member, lower cliff-forming member, and upper cliff-forming member. Triticites, Schwagerina, and Schubertella kingi in the platy limestone member indicate an early Wolfcampian age. Schwagerina, Schubertella kingi, and a distinctive assemblage of brachiopods, similar to the West Texas fauna, indicate that the upper cliff-forming member is late Wolfcampian. The lower cliff-forming member is tentatively assigned to the middle Wolfcampian. The Wamp Spring sequence correlates temporally with the BSe 'formation' of the Bird Spring Group. The fossil-rich upper cliff-forming limestone member includes the new species Pontisia boodi, Crurithyris wampensis, and Calliprotonia(?) n. sp. A, as well as Hustedia culcitula, Crenispirifer(?) sp., Cenorhynchia(?) sp., Kutorginella(?) sp., marginiferids, lyssacine hexactinellid sponges, pleurotomarid and bellerophontid gastropods, cidaroid echinoids, rugose corals, cylindrical cryptostome bryozoans, and nuculids. -from Authors

Developing a composite based elliptic spring for automotive applications

International Nuclear Information System (INIS)

Talib, Abdul Rahim Abu; Ali, Aidy; Goudah, G.; Lah, Nur Azida Che; Golestaneh, A.F.

2010-01-01

An automotive suspension system is designed to provide both safety and comfort for the vehicle occupants. In this study, finite element models were developed to optimize the material and geometry of the composite elliptical spring based on the spring rate, log life and shear stress parameters. The influence of the ellipticity ratio on the performance of woven roving-wrapped composite elliptical springs was investigated both experimentally and numerically. The study demonstrated that composite elliptical springs can be used for light and heavy trucks with substantial weight reduction. The results showed that the ellipticity ratio significantly influenced the design parameters. Composite elliptic springs with ellipticity ratios of a/b = 2 had the optimum spring parameters.

Spring Small Grains Area Estimation

Science.gov (United States)

Palmer, W. F.; Mohler, R. J.

1986-01-01

SSG3 automatically estimates acreage of spring small grains from Landsat data. Report describes development and testing of a computerized technique for using Landsat multispectral scanner (MSS) data to estimate acreage of spring small grains (wheat, barley, and oats). Application of technique to analysis of four years of data from United States and Canada yielded estimates of accuracy comparable to those obtained through procedures that rely on trained analysis.

Process improvements for enhanced productivity of PHWR garter springs

International Nuclear Information System (INIS)

Srinivasula Reddy, S.; Tonpe, Sunil; Saibaba, N.; Jayaraj, R.N.

2009-01-01

Full text: In Pressurised Heavy Water Reactors (PHWR), Garter springs are used as spacers between the coolant tube and calandria tube. Garter springs are made from Zirconium alloy containing 2.5 % Niobium and 0.5% copper. The springs are basically manufactured by coiling a wire of cross section 1.7 mm x 1.0 mm, which is produced by series of drawing and swaging operations using hot extruded rods of 19 mm diameter. The manufacturing process also involves heat treatment and chemical cleaning operations at appropriate stages. It is required to ensure that the life of springs against parameters like hydrogen pickup, residual stresses and low stiffness is improved at the manufacturing stage itself by improving manufacturing process. The impact of above problems on spring life and process improvements is briefly discussed. The critical factor affecting the garter spring performance in PHWR Reactor is mainly hydrogen. The life limiting factors for garter springs are the problems arising out of high total hydrogen content, which depends on the hydrogen pickup during reactor operation. This phenomenon can happen during the reactor operation, as springs are prone to pick-up hydrogen in the reactor environment. Hence acceptable hydrogen content for the springs is specified as 25 ppm (max.). Garter spring is susceptible to hydrogen pick-up during various production processes, which make material brittle and difficult for fabrication process such as wire drawing and coiling. By studying and optimizing the process parameters of spring manufacturing, the hydrogen pick-up of springs is brought down from 70 ppm to a level of 20 ppm. Garter springs are provided with a hook at each end to enable its assembly to coolant tube in the reactor. The hook portion is very critical in maintaining the integrity of the spring. It is desirable to have the hook portion relieved of all residual stresses. For this purpose manufacturing process has been modified and solutionising was introduced as

Hydrogeochemical And Isotopic Investigation Of Nasrettin Hoca Springs, Eskisehir, Turkey

Directory of Open Access Journals (Sweden)

Mehmet ÇELİK

2013-06-01

Full Text Available The aims of this study are to investigate the water quality, the contamination and water-rock interaction of the Nasrettin Hoca springs, with an ultimate aim of establishing protection measures. Within the scope of this study, the springs in and around the catchment area, Bağbaşı springs, Hatip spring, Ali spring, Saracık Fountain and Babadat spring, were investigated. The springs are of Ca-Mg-HCO3 type when basic hydrogeochemical features are considered, are under the influence of marble-limestone and meta ophiolitic units located in the recharge area and are of shallow circulation. The trace element contents of the springs show the influence of the carbonate rocks comprising the reservoir (Sr and the basement rocks (Ni, Al. The protection areas of Nasrettin Hoca springs against contamination are determined as three different zones by considering the hydrogeologic and topographical features of the region and the Turkish Standards

Structural analysis of compression helical spring used in suspension system

Science.gov (United States)

Jain, Akshat; Misra, Sheelam; Jindal, Arun; Lakhian, Prateek

2017-07-01

The main aim of this work has to develop a helical spring for shock absorber used in suspension system which is designed to reduce shock impulse and liberate kinetic energy. In a vehicle, it increases comfort by decreasing amplitude of disturbances and it improves ride quality by absorbing and dissipating energy. When a vehicle is in motion on a road and strikes a bump, spring comes into action quickly. After compression, spring will attempt to come to its equilibrium state which is on level road. Helical springs can be made lighter with more strength by reducing number of coils and increasing the area. In this research work, a helical spring is modeled and analyzed to substitute the existing steel spring which is used in suspension. By using different materials, stress and deflection of helical spring can be varied. Comparability between existing spring and newly replaced spring is used to verify the results. For finding detailed stress distribution, finite element analysis is used to find stresses and deflection in both the helical springs. Finite element analysis is a method which is used to find proximate solutions of a physical problem defined in a finite domain. In this research work, modeling of spring is accomplished using Solid Works and analysis on Ansys.

Hydrogeological characterization of peculiar Apenninic springs

Science.gov (United States)

Cervi, F.; Marcaccio, M.; Petronici, F.; Borgatti, L.

2014-09-01

In the northern Apennines of Italy, springs are quite widespread over the slopes. Due to the outcropping of low-permeability geologic units, they are generally characterized by low-yield capacities and high discharge variability during the hydrologic year. In addition, low-flow periods (discharge lower than 1 Ls-1) reflect rainfall and snowmelt distribution and generally occur in summer seasons. These features strongly condition the management for water-supply purposes, making it particularly complex. The "Mulino delle Vene" springs (420 m a.s.l., Reggio Emilia Province, Italy) are one of the largest in the Apennines for mean annual discharge and dynamic storage and are considered as the main water resource in the area. They flow out from several joints and fractures at the bottom of an arenite rock mass outcrop in the vicinity of the Tresinaro River. To date, these springs have not yet been exploited, as the knowledge about the hydrogeological characteristics of the aquifer and their hydrological behaviour is not fully achieved. This study aims to describe the recharge processes and to define the hydrogeological boundaries of the aquifer. It is based on river and spring discharge monitoring and groundwater balance assessment carried out during the period 2012-2013. Results confirm the effectiveness of the approach, as it allowed the total aliquot of discharge of the springs to be assessed. Moreover, by comparing the observed discharge volume with the one calculated with the groundwater balance, the aquifer has been identified with the arenite slab (mean altitude of 580 m a.s.l.), extended about 5.5 km2 and located 1 km west of the monitored springs.

Magnetic spring based on two permanent magnets

International Nuclear Information System (INIS)

Tsivilitsin, V.Yu.; Mil'man, Yu.V.; Goncharuk, V.A.; Bondar, I.B.

2011-01-01

A new type of the magnetic spring construction 'two permanent magnets' has been considered. A mathematical expression for the estimation of a pulling-in force has been offered. This expression is verified experimentally on the produced operating magnetic spring. The theoretical and experimental data are in good accordance. A number of advantages of the magnetic spring over the construction 'permanent magnet - magnetic circuit' such as an insignificant friction force between two magnets and a higher pulling force are discussed.

Bioinspired spring origami

Science.gov (United States)

Faber, Jakob A.; Arrieta, Andres F.; Studart, André R.

2018-03-01

Origami enables folding of objects into a variety of shapes in arts, engineering, and biological systems. In contrast to well-known paper-folded objects, the wing of the earwig has an exquisite natural folding system that cannot be sufficiently described by current origami models. Such an unusual biological system displays incompatible folding patterns, remains open by a bistable locking mechanism during flight, and self-folds rapidly without muscular actuation. We show that these notable functionalities arise from the protein-rich joints of the earwig wing, which work as extensional and rotational springs between facets. Inspired by this biological wing, we establish a spring origami model that broadens the folding design space of traditional origami and allows for the fabrication of precisely tunable, four-dimensional–printed objects with programmable bioinspired morphing functionalities.

Chemical characteristics of the major thermal springs of Montana

Energy Technology Data Exchange (ETDEWEB)

Mariner, R.H.; Presser, T.S.; Evans, W.C.

1976-07-01

Twenty-one thermal springs in western Montana were sampled for chemical, isotope, and gas compositions. Most of the springs issue dilute to slightly saline sodium-bicarbonate waters of neutral to slightly alkaline pH. A few of the springs issue sodium-mixed anion waters of near neutral pH. Fluoride concentrations are high in most of the thermal waters, up to 18 miligrams per litre, while F/Cl ratios range from 3/1 in the dilute waters to 1/10 in the slightly saline waters. Most of the springs are theoretically in thermodynamic equilibrium with respect to calcite and fluorite. Nitrogen is the major gas escaping from most of the hot springs; however, Hunters Hot Springs issue principally methane. The deuterium content of the hot spring waters is typical of meteoric water in western Montana. Geothermal calculations based on silica concentrations and Na-K-Ca ratios indicate that most of the springs are associated with low temperature aquifers (less than 100/sup 0/C). Chalcedony may be controlling the silica concentrations in these low temperature aquifers even in ''granitic'' terranes.

Geothermal energy and hot springs in Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Koga, T. (Hot Springs Therapeutics Research Institute, Kyushu, Univ., Japan)

1971-01-01

The hot springs in Ethiopia are concentrated in two areas: the North Afar depression and adjacent Red Sea shore, and a geothermal field 100 km from northeast to southwest in the central part of Ethiopia. The latter extends not only to the Great Rift Valley but also to the Aden Gulf. In the lake district in the central Great Rift Valley, there are a number of hot springs on the lake shore. These are along NE-SW fault lines, and the water is a sodium bicarbonate-type rich in HCO/sub 3/ and Na but low in C1 and Ca. In Dallol in the North Afar depression, CO/sub 2/-containing hot springs with high temperatures (110/sup 0/C) and a specific gravity of 1.4, were observed. In the South Afar depression, located in the northeastern part of the Rift Valley, there are many active volcanoes and hot springs between the lake district and the Danakil depression. The spring water is a sodium bicarbonate saline type. Nine graphs and maps are included.

Report on the FY 1998 survey for preservation of Jozankei Hot Spring. Hot spring variation survey; 1998 nendo Jozankei onsen hozen chosa. Onsen hendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Of the FY 1998 survey for preservation of Jozankei Hot Spring, a survey was conducted with the aim of grasping the state of variation in ingredients of hot spring, etc. in the area and of elucidating the causes of hot spring variation. During the period from October 27, 1998 to August 28, 1999, the following were carried out: sampling of specimens of spring water at 6 spring sources, river water at 2 points and precipitation at 2 points; measurement of temperature, spring temperature, pH, electric conductivity, etc.; analyses of Na, Ca, CL, HCO{sub 3}, SiO{sub 2}, etc. The results of the analysis are as follows. As to spring sources, A-2, A-7 and B-1, the precipitation or river water flow rate seem to largely affect the variation in hot spring measuring values. As to spring resources, A-6 and B-4, the relation with the precipitation or river water flow rate is not clear, but a big change is recognized in the snow-melting season. The tendency to the two variations seems to be caused by the difference between the spring with which the river water is greatly concerned by the crack system of the spring having reached the river and the spring which was closed on the earth surface. The temperature variation of springs was considered to be affected by the river water which flowed into the springs. (NEDO)

Pemodelan Desain Sol Sepatu dengan Inovasi Penambahan Wave Spring

Directory of Open Access Journals (Sweden)

Redyarsa Dharma Bintara

2015-07-01

Full Text Available Desain sepatu sport berkembang pesat dengan tujuan mengurangi cedera dan meningkatkankenyamanan pengguna. Pengurangan cedera dilakukan dengan cara memperbesar energi yangdiserap dari beban akibat pengguna berlari atau melompat. Pada penelitian ini dilakukanpenambahan wave spring yang digunakan sebagai mekanisme penyerap beban.Pemodelandilakukan pada sol sepatu dengan menggunakan bantuan software finite element method (FEMAnsys 14.5 Academic. Model awal dilakukan untuk mengetahui batas deformasi sol sepatu yangakan dimanfaatkan sebagai input model berikutnya yaitu model dengan diberikan inovasipenambahan wave spring. Analisa difokuskan pada sol sepatu bagian belakang (tumit kaki.Darihasil simulasi, didapatkan bahwa penyerapan energi sol sepatu dengan penambahan wave springlebih besar daripada penyerapan energi sol sepatu tanpa penambahan wave spring, sehinggapenambahan wave spring memungkinkan untuk diaplikasikan pada sol sepatu sport.Kata kunci: Penyerapan energi, wave spring, sol sepatu. Sport shoe design had been developed rapidly with the purpose to reduce injuries and increaseuser comfort. Reduction of injury is done by enlarging the energy absorbed from the user running orjumping load. In this study, the addition of the wave spring is used as the load absorbingmechanism. The shoes sole is modeled by using finite element method (FEM software Ansys 14.5Academic. Initial model was conducted to determine the deformation boundary in soles which willbe used as input to the next model for the wave spring addition innovation. Analysis focused onshoe sole on heel foot. From the simulation results, it was found that the energy absorption shoessoles with the addition of the wave spring is greater than the energy absorption soles without theaddition of wave spring. It can be concluded that the addition of a spring wave can be applied to thesoles of sports shoes.Keywords: Energy absorb, wave spring, shoe sole, deformation boundary

Development of alternative materials for BWR fuel springs

International Nuclear Information System (INIS)

Uruma, Y.; Osato, T.; Yamazaki, K.

2002-01-01

Major sources of radioactivity introduced into reactor water of BWR were estimated fuel crud and in-core materials (especially, fuel springs). Fuel springs are used for fixation of fuel cladding tubes with spacer grid. Those are small parts (total length is only within 25 mm) and so many numbers are loaded simultaneously and then total surfaces area are calculated up to about 200 m 2 . Fuel springs are located under high radiation field and high oxidative environment. Conventional fuel spring is made of alloy-X750 which is one of nickel-based alloy and is reported to show relatively higher corrosion release rate. 58 Co and 60 Co will be released directly into reactor water from intensely radio-activated fuel springs surface and increase radioactivity concentrations in primary coolant. Corrosion release control from fuel springs is an important technical item and a development of alternative material instead of alloy-X750 for fuel spring is a key subject to achieve ultra low man-rem exposure BWR plant. In present work, alloy-X718 which started usage for PWR fuel springs and stainless steel type 316L which has many mechanical property data are picked up for alternative materials and compared their corrosion behaviors with conventional material. Corrosion experiment was conducted under vapor-water two phases flow which is simulated fuel cladding surface boiling condition. After exposure, corrosion film formed under corrosion test was analyzed in detail and corrosion film amount and corrosion release amount are estimated among three materials. (authors)

Microscopic modelling of air spring bellows. Automation in the lifetime estimation of air springs; Mikroskopische Balgmodellierung. Automatismen in der Lebensdauerabschaetzung von Luftfedern

Energy Technology Data Exchange (ETDEWEB)

Pham, Tram Anh; Brueger, Thorsten [Vibracoustic GmbH und Co. KG, Hamburg (Germany); Rambacher, Christoph [Professur fuer Maschinenelemente und Produktentwicklung (MRP), Helmut-Schmidt-Univ., Hamburg (HSU) (Germany)

2009-07-01

Because of the many advantages of air springs over conventional springs, they are being increasingly fitted in upper and middle class automobiles. Generally air spring bellows, consisting of reinforcing cords and elastomer, can be simulated using the rebar technique. The following article introduces a method in which the boundary conditions derived from the model simulated with the rebar technique are applied in the air spring bellow ''microscopic model'' which is modelled automatically. The microscopic modelling enables a detailed analysis of stress and strain conditions in the elastomer. With the automated process this method can be applied for the widespread design process for air spring systems. Finally the validation of the method is demonstrated. (orig.)

Springing Response Due to Directional Wave Field Excitation

DEFF Research Database (Denmark)

Vidic-Perunovic, Jelena; Jensen, Jørgen Juncher

2004-01-01

This paper analyses the wave-induced high-frequency bending moment response of ships, denoted springing. The aim is to predict measured severe springing responses in a large bulk carrier. It is shown that the most important springing contribution is due to the resultant second order excitation...... in multidirectional sea. The incident pressure field from the second order bidirectional wave field is derived, including the non-linear cross-coupling terms between the two wave systems (e.g. wind driven waves and swell). The resulting effect of the super-harmonic cross-coupling interaction terms on the springing...... response is discussed. An example with opposing waves is given, representing probably the 'worst' case for energy exchange between the wave systems. Theoretical predictions of standard deviation of wave- and springing-induced stress amidships are compared with full-scale measurements for a bulk carrier....

Archaeal Nitrification in Hot Springs

Science.gov (United States)

Richter, A.; Daims, H.; Reigstad, L.; Wanek, W.; Wagner, M.; Schleper, C.

2006-12-01

Biological nitrification, i.e. the aerobic conversion of ammonia to nitrate via nitrite, is a major component of the global nitrogen cycle. Until recently, it was thought that the ability to aerobically oxidize ammonia was confined to bacteria of the phylum Proteobacteria. However, it has recently been shown that Archaea of the phylum Crenarchaeota are also capable of ammonia oxidation. As many Crenarchaeota are thermophilic or hyperthermophilic, and at least some of them are capable of ammonia oxidation we speculated on the existence of (hyper)thermophilic ammonia-oxidizing archaea (AOA). Using PCR primers specifically targeting the archaeal ammonia monooxygenase (amoA) gene, we were indeed able to confirm the presence of such organisms in several hot springs in Reykjadalur, Iceland. These hot springs exhibited temperatures well above 80 °C and pH values ranging from 2.0 to 4.5. To proof that nitrification actually took place under these extreme conditions, we measured gross nitrification rates by the isotope pool dilution method; we added 15N-labelled nitrate to the mud and followed the dilution of the label by nitrate production from ammonium either in situ (incubation in the hot spring) or under controlled conditions in the laboratory (at 80 °C). The nitrification rates in the hot springs ranged from 0.79 to 2.22 mg nitrate-N per L of mud and day. Controls, in which microorganisms were killed before the incubations, demonstrated that the nitrification was of biological origin. Addition of ammonium increased the gross nitrification rate approximately 3-fold, indicating that the nitrification was ammonium limited under the conditions used. Collectively, our study provides evidence that (1) AOA are present in hot springs and (2) that they are actively nitrifying. These findings have major implications for our understanding of nitrogen cycling of hot environments.

Microbiological studies of hot springs in India: a review.

Science.gov (United States)

Poddar, Abhijit; Das, Subrata K

2018-01-01

The earliest microbiological studies on hot springs in India date from 2003, a much later date compared to global attention in this striking field of study. As of today, 28 out of 400 geothermal springs have been explored following both culturable and non-culturable approaches. The temperatures and pH of the springs are 37-99 °C and 6.8-10, respectively. Several studies have been performed on the description of novel genera and species, characterization of different bio-resources, metagenomics of hot spring microbiome and whole genome analysis of few isolates. 17 strains representing novel species and many thermostable enzymes, including lipase, protease, chitinase, amylase, etc. with potential biotechnological applications have been reported by several authors. Influence of physico-chemical conditions, especially that of temperature, on shaping the hot spring microbiome has been established by metagenomic investigations. Bacteria are the predominant life forms in all the springs with an abundance of phyla Firmicutes, Proteobacteria, Actinobacteria, Thermi, Bacteroidetes, Deinococcus-Thermus and Chloroflexi. In this review, we have discussed the findings on all microbiological studies that have been carried out to date, on the 28 hot springs. Further, the possibilities of extrapolating these studies for practical applications and environmental impact assessment towards protection of natural ecosystem of hot springs have also been discussed.

Instant Spring security starter

CERN Document Server

Jagielski, Piotr

2013-01-01

Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks. A concise guide written in an easy-to-follow format following the Starter guide approach.This book is for people who have not used Spring Security before and want to learn how to use it effectively in a short amount of time. It is assumed that readers know both Java and HTTP protocol at the level of basic web programming. The reader should also be familiar with Inversion-of-Control/Dependency Injection, preferably with the Spring framework itsel

SPring-8 and application of nuclear scattering

Energy Technology Data Exchange (ETDEWEB)

Harami, Taikan [Japan Atomic Energy Research Inst., Kamigori, Hyogo (Japan). Kansai Research Establishment

1997-03-01

The SPring-8 has Linac synchrotron, incidence type facility and an accumulation ring. By preparing a beam line to take out light at the accumulation ring, the SPring-8 is supplied for common applications. Development of science adopting new method to study of properties and organisms by using high brightness source is expected. Construction of the SPring-8 accelerator was finished and adjusting test and commissioning of apparatuses are now in proceeding. At pre-use inspection of the accumulation ring on March, 1997, beam lines for R and D and crystalline structure analysis are applied to the Science and Technology Agency to inspect them simultaneously. And, by activating character of the SPring-8 radiation facility of high brightness and high energy X-ray generator, property study using Moessbauer nuclide to a probe can be conducted. (G.K.)

Experimental investigations of higher-order springing and whipping-WILS project

Directory of Open Access Journals (Sweden)

Hong Sa Young

2014-12-01

Full Text Available Springing and whipping are becoming increasingly important considerations in ship design as container ships increase in size. In this study, the springing and whipping characteristics of a large container ship were investigated through a series of systematic model tests in waves. A multi-segmented hull model with a backbone was adopted for measurement of springing and whipping signals. A conversion method for extracting torsion springing and whipping is described in this paper for the case of an open-section backbone. Higher-order springing, higher-mode torsion responses, and the effects of linear and nonlinear springing in irregular waves are highlighted in the discussion.

Reactivation of Open Coil Springs: A Novel Procedure

Directory of Open Access Journals (Sweden)

Sanjeeb Kumar Sahu

2012-01-01

Full Text Available Open coil springs are commonly used in orthodontic practice to create space for a palatally or lingually blocked out tooth. However, very often the clinician encounters a situation where the inter-bracket span is very less and the open coil spring is not long enough to open the required space needed for alignment. In such situations, the clinician needs to remove the arch wire and reinserts a longer coil spring. A new simple and cost-effective technique describes an intraoral reactivation of an open coil spring without the need for removal of the base archwire with the additional benefit of preventing unwanted forces to the adjacent teeth.

Radiological Studies in the Hot Spring Region of Oyoun Mossa and Hammam Faraun Thermal Spring Areas in Western Sinai

International Nuclear Information System (INIS)

Ramadan, Kh.A.; Badran, H.M.; Ramadan, Kh.A.; Seddeek, M.K.; Sharshar, T.; Sharshar, T.

2009-01-01

Radioactivity in and around the two hot springs, Oyoun Mossa and Hammam Faraun, Western Sinai has been determined. The ground water, sediment and sand samples were measured by gamma-ray spectrometer for 232 Th, 226 Ra and 40 K isotopes. The enrichment of 226 Ra in Hammam Faraun hot spring was the most prominent feature. The concentration of 226 Ra in Oyoun Mossa and Hammam Faraun hot springs are 68 and 2377 Bq/kg for sediments, 3.5 and 54.7 Bq/kg for wild plants, and 205 and 1945 mBq/l for the ground water, respectively. In addition, the concentration of sand samples are 14 times larger in the area of Hammam Faraun compared with that of Oyoun Mossa. On the other hand, the concentration of 232 Th in different samples are comparable in the two areas while 137 Cs concentrations are relatively higher in Oyoun Mossa. For the purpose of comparison, sand samples were collected from two locations 5-12 km away from each spring. The activity concentrations of the four locations are comparable and in agreement with those from the area of the two springs except in one case. The major difference was the activity concentration of 226 Ra in the area of Hammam Faraun, which is much higher. The concentrations of all detected isotopes in water samples from these two springs are much higher than that detected in 27 natural wells in north Sinai. The results of the present study indicate that water only in Hammam Faraun hot spring is contaminated with 238 U-isotopes and the surrounding area is affected by this contamination. The calculated annual effective dose equivalents in the surroundings of Hammam Faraun (81.8 μSv) is superior to the maximum contaminant levels recommended.

The first CERN Spring Campus

CERN Multimedia

CERN Bulletin

2014-01-01

From 14 to 16 April, the first edition of the CERN Spring Campus took place in Spain. Taking place over three intensive days, this event brought experts from CERN together at the University of Oviedo, where they met the engineers and scientists of the future in a programme of scientific and technological dissemination and cultural exchange.   The young participants of the first CERN Spring Campus and their instructors show their enthusiasm after the intensive three-day course. “This three-day school focuses on preparing young engineers for the job market, with a particular emphasis on computing,” explains Derek Mathieson, Advanced Information Systems Group Leader in the GS Department and Head of the CERN Spring Campus organising committee. “We organised talks on entrepreneurship and IT, as well as on job interviews and CV writing. It was also an important opportunity for the participants to meet CERN computing engineers to find out what it is like to work in I...

Mechanics of anisotropic spring networks.

Science.gov (United States)

Zhang, T; Schwarz, J M; Das, Moumita

2014-12-01

We construct and analyze a model for a disordered linear spring network with anisotropy. The modeling is motivated by, for example, granular systems, nematic elastomers, and ultimately cytoskeletal networks exhibiting some underlying anisotropy. The model consists of a triangular lattice with two different bond occupation probabilities, p(x) and p(y), for the linear springs. We develop an effective medium theory (EMT) to describe the network elasticity as a function of p(x) and p(y). We find that the onset of rigidity in the EMT agrees with Maxwell constraint counting. We also find beyond linear behavior in the shear and bulk modulus as a function of occupation probability in the rigid phase for small strains, which differs from the isotropic case. We compare our EMT with numerical simulations to find rather good agreement. Finally, we discuss the implications of extending the reach of effective medium theory as well as draw connections with prior work on both anisotropic and isotropic spring networks.

Nano-G accelerometer using geometric anti-springs

NARCIS (Netherlands)

Boom, B. A.; Bertolini, A.; Hennes, E.; Brookhuis, R. A.; Wiegerink, R. J.; Van Den Brand, J. F J; Beker, M. G.; Oner, A.; Van Wees, D.

2017-01-01

We report an ultra-sensitive seismic accelerometer with nano-g sensitivity, using geometric anti-spring technology. High sensitivity is achieved by an on-chip mechanical preloading system comprising four sets of curved leaf springs that support a proof-mass. Using this preloading mechanism,

Analysis of methods to estimate spring flows in a karst aquifer.

Science.gov (United States)

Sepúlveda, Nicasio

2009-01-01

Hydraulically and statistically based methods were analyzed to identify the most reliable method to predict spring flows in a karst aquifer. Measured water levels at nearby observation wells, measured spring pool altitudes, and the distance between observation wells and the spring pool were the parameters used to match measured spring flows. Measured spring flows at six Upper Floridan aquifer springs in central Florida were used to assess the reliability of these methods to predict spring flows. Hydraulically based methods involved the application of the Theis, Hantush-Jacob, and Darcy-Weisbach equations, whereas the statistically based methods were the multiple linear regressions and the technology of artificial neural networks (ANNs). Root mean square errors between measured and predicted spring flows using the Darcy-Weisbach method ranged between 5% and 15% of the measured flows, lower than the 7% to 27% range for the Theis or Hantush-Jacob methods. Flows at all springs were estimated to be turbulent based on the Reynolds number derived from the Darcy-Weisbach equation for conduit flow. The multiple linear regression and the Darcy-Weisbach methods had similar spring flow prediction capabilities. The ANNs provided the lowest residuals between measured and predicted spring flows, ranging from 1.6% to 5.3% of the measured flows. The model prediction efficiency criteria also indicated that the ANNs were the most accurate method predicting spring flows in a karst aquifer.

Radioactivity measurement in spring waters of Cantabria, Spain

International Nuclear Information System (INIS)

Soto Torres, J.; Gomez Arozamena, J.

1999-01-01

A study of the radioactivity existing in a high number of springs located in Cantabria, Northern Spain, was made. The spring analyzed in three sampling campaign's, And alpha and beta total activities and 226 Ra and 222 Rn concentrations were determined for each sample. The measuring techniques employed were gamma spectrometry with Ge detector, counting with gas flow proportional counter, and counting with ZnS(Ag) scintillating detector. Results show that springs with high radon water concentration have high values respect to the national mean. The springs with the highest radium and radon levels have thermal waters and are located on two deep fault, those have historic seismicity and seismical and geomorphological evidences of recent tectonic activity

Bacterial and archaeal diversities in Yunnan and Tibetan hot springs, China.

Science.gov (United States)

Song, Zhao-Qi; Wang, Feng-Ping; Zhi, Xiao-Yang; Chen, Jin-Quan; Zhou, En-Min; Liang, Feng; Xiao, Xiang; Tang, Shu-Kun; Jiang, Hong-Chen; Zhang, Chuanlun L; Dong, Hailiang; Li, Wen-Jun

2013-04-01

Thousands of hot springs are located in the north-eastern part of the Yunnan-Tibet geothermal zone, which is one of the most active geothermal areas in the world. However, a comprehensive and detailed understanding of microbial diversity in these hot springs is still lacking. In this study, bacterial and archaeal diversities were investigated in 16 hot springs (pH 3.2-8.6; temperature 47-96°C) in Yunnan Province and Tibet, China by using a barcoded 16S rRNA gene-pyrosequencing approach. Aquificae, Proteobacteria, Firmicutes, Deinococcus-Thermus and Bacteroidetes comprised the large portion of the bacterial communities in acidic hot springs. Non-acidic hot springs harboured more and variable bacterial phyla than acidic springs. Desulfurococcales and unclassified Crenarchaeota were the dominated groups in archaeal populations from most of the non-acidic hot springs; whereas, the archaeal community structure in acidic hot springs was simpler and characterized by Sulfolobales and Thermoplasmata. The phylogenetic analyses showed that Aquificae and Crenarchaeota were predominant in the investigated springs and possessed many phylogenetic lineages that have never been detected in other hot springs in the world. Thus findings from this study significantly improve our understanding of microbial diversity in terrestrial hot springs. © 2012 Society for Applied Microbiology and Blackwell Publishing Ltd.

A Study on the Fuel Assembly Seismic Analysis without Holddown Springs

International Nuclear Information System (INIS)

Kwon, O Cheol; Ha, Dong Geun; Lee, Kyou Seok; Jeon, Sang Yoon; Suh, Jung Min

2013-01-01

In this study, the effect for the fuel assembly removed holddown spring under seismic event has been evaluated through the comparison with the seismic analysis result of fuel assembly with holddown spring. In order to compare each design, the simplified fuel assembly seismic analysis models have been established according to reference. The mid grid impact force, natural frequency, and top nozzle displacement for each fuel assembly model has been analyzed using ANSYS. The fuel assembly seismic analyses without holddown springs are performed and compared to the model with holddown springs. The grid impact forces of CPM 1 and CPM 2 are almost doubled in comparison with CPM 3 and almost tripled in comparison with CPM 4 so the grid impact forces depend on CPM types. The grid impact forces of the fuel assembly model without holddown springs have similar tendencies in comparison with fuel assembly with holddown springs. Moreover, the model without holddown springs analysis time is much longer than the model with holddown springs. Consequently, it is moderate that the fuel assembly analysis model with holddown springs would be used for effective analysis even though the actual model has no holddown springs

A Study on the Fuel Assembly Seismic Analysis without Holddown Springs

Energy Technology Data Exchange (ETDEWEB)

Kwon, O Cheol; Ha, Dong Geun; Lee, Kyou Seok; Jeon, Sang Yoon; Suh, Jung Min [KEPCO Nuclear Fuel, Daejeon (Korea, Republic of)

2013-10-15

In this study, the effect for the fuel assembly removed holddown spring under seismic event has been evaluated through the comparison with the seismic analysis result of fuel assembly with holddown spring. In order to compare each design, the simplified fuel assembly seismic analysis models have been established according to reference. The mid grid impact force, natural frequency, and top nozzle displacement for each fuel assembly model has been analyzed using ANSYS. The fuel assembly seismic analyses without holddown springs are performed and compared to the model with holddown springs. The grid impact forces of CPM{sub 1} and CPM{sub 2} are almost doubled in comparison with CPM{sub 3} and almost tripled in comparison with CPM{sub 4} so the grid impact forces depend on CPM types. The grid impact forces of the fuel assembly model without holddown springs have similar tendencies in comparison with fuel assembly with holddown springs. Moreover, the model without holddown springs analysis time is much longer than the model with holddown springs. Consequently, it is moderate that the fuel assembly analysis model with holddown springs would be used for effective analysis even though the actual model has no holddown springs.

Nuclear reactor spring strip grid spacer

International Nuclear Information System (INIS)

Patterson, J.F.; Flora, B.S.

1980-01-01

An improved and novel grid spacer was developed for use in nuclear reactor fuel assemblies. It is comprised of a series of intersecting support strips and a peripheral support band attached to the ends of the support strips. Each of the openings into which the fuel element is inserted has a number of protruding dimples and springs extending in different directions. The dimples coact with the springs to secure the fuel rods in the openings. Compared with previous designs, this design gives more positive alignment of the support stips while allowing greater flexibility to counterbalance the effects of thermal expansion. The springs are arranged in alternating directions so that the reaction forces tend to counterbalance each other, which in turn minimizes the reaction loads on the supporting structure. (D.N.)

Mechanics of patterned helical Si springs on Si substrate.

Science.gov (United States)

Liu, D L; Ye, D X; Khan, F; Tang, F; Lim, B K; Picu, R C; Wang, G C; Lu, T M

2003-12-01

The elastic response, including the spring constant, of individual Si helical-shape submicron springs, was measured using a tip-cantilever assembly attached to a conventional atomic force microscope. The isolated, four-turn Si springs were fabricated using oblique angle deposition with substrate rotation, also known as the glancing angle deposition, on a templated Si substrate. The response of the structures was modeled using finite elements, and it was shown that the conventional formulae for the spring constant required modifications before they could be used for the loading scheme used in the present experiment.

Examining Neosho madtom reproductive biology using ultrasound and artificial photothermal cycles

Science.gov (United States)

Bryan, J.L.; Wildhaber, M.L.; Noltie, Douglas B.

2005-01-01

We examined whether extended laboratory simulation of natural photothermal conditions could stimulate reproduction in the Neosho madtom Noturus placidus, a federally threatened species. For 3 years, a captive population of Neosho madtoms was maintained under simulated natural conditions and monitored routinely with ultrasound for reproductive condition. Female Neosho madtoms cycled in and out of spawning condition, producing and absorbing oocytes annually. Internal measurements made by means of ultrasound indicated the summer mean oocyte size remained consistent over the years, although estimated fecundity increased with increasing fish length. In the summer of 2001, after 3 years in the simulated natural environment, 13 out of 41 fish participated in 10 spawnings. Simulation of the natural photothermal environment, coupled with within-day temperature fluctuations during the spring rise, seemed important for the spawning of captive Neosho madtoms. The use of ultrasound to assess the reproductive status in Neosho madtoms was effective and resulted in negligible stress or injury to the fish. These procedures may facilitate future culture of this species and other madtoms Noturus spp., especially when species are rare, threatened, or endangered. ?? Copyright by the American Fisheries Society 2005.

Earlier vegetation green-up has reduced spring dust storms.

Science.gov (United States)

Fan, Bihang; Guo, Li; Li, Ning; Chen, Jin; Lin, Henry; Zhang, Xiaoyang; Shen, Miaogen; Rao, Yuhan; Wang, Cong; Ma, Lei

2014-10-24

The observed decline of spring dust storms in Northeast Asia since the 1950s has been attributed to surface wind stilling. However, spring vegetation growth could also restrain dust storms through accumulating aboveground biomass and increasing surface roughness. To investigate the impacts of vegetation spring growth on dust storms, we examine the relationships between recorded spring dust storm outbreaks and satellite-derived vegetation green-up date in Inner Mongolia, Northern China from 1982 to 2008. We find a significant dampening effect of advanced vegetation growth on spring dust storms (r = 0.49, p = 0.01), with a one-day earlier green-up date corresponding to a decrease in annual spring dust storm outbreaks by 3%. Moreover, the higher correlation (r = 0.55, p storm outbreak ratio (the ratio of dust storm outbreaks to times of strong wind events) indicates that such effect is independent of changes in surface wind. Spatially, a negative correlation is detected between areas with advanced green-up dates and regional annual spring dust storms (r = -0.49, p = 0.01). This new insight is valuable for understanding dust storms dynamics under the changing climate. Our findings suggest that dust storms in Inner Mongolia will be further mitigated by the projected earlier vegetation green-up in the warming world.

Spring and Its Global Echo: Quantitative Analysis

Directory of Open Access Journals (Sweden)

A. V. Korotayev

2017-01-01

Full Text Available It is shown that the Arab Spring acted as a trigger for a global wave of socio-political destabilization, which signifi cantly exceeded the scale of the Arab Spring itself and affected absolutely all world-system zones. Only in 2011 the growth of the global number of largescale anti-government demonstrations, riots and political strikes was to a high degree (although not entirely due to their growth in the Arab world. In the ensuing years, the Arab countries rather made a negative contribution to a very noticeable further increase in the global number of large-scale anti-government demonstrations, riots and general strikes (the global intensity of all these three important types of socio-political destabilization continued to grow despite the decline in the Arab world. Thus, for all these three important indicators of sociopolitical destabilization, the scale of the global echo of the Arab Spring has overshadowed the scale of the Arab Spring itself. Only as regards the fourth considered indicator (major terrorist attacks / guerrilla warfare the scale of the global echo for the entire period considered did not overshadow the scale of the Arab Spring (and, incidentally, «Winter» - and in 2014-2015 Arab countries continued to make a disproportionate contribution to the historically record global values of this sad indicator – global number of major terrorist attacks/ guerilla warfare. To conclude, triggered by the Arab Spring, the global wave of socio-political destabilization led after 2010 to a very signifi cant growth of socio-political instability in absolutely all World System zones. However, this global destabilization wave manifested itself in different World System zones in different ways and not completely synchronously.

Nonlinear Quantum Optical Springs and Their Nonclassical Properties

International Nuclear Information System (INIS)

Faghihi, M.J.; Tavassoly, M.K.

2011-01-01

The original idea of quantum optical spring arises from the requirement of quantization of the frequency of oscillations in the Hamiltonian of harmonic oscillator. This purpose is achieved by considering a spring whose constant (and so its frequency) depends on the quantum states of another system. Recently, it is realized that by the assumption of frequency modulation of ω to ω√1+μa † a the mentioned idea can be established. In the present paper, we generalize the approach of quantum optical spring with particular attention to the dependence of frequency to the intensity of radiation field that naturally observes in the nonlinear coherent states, from which we arrive at a physical system has been called by us as nonlinear quantum optical spring. Then, after the introduction of the generalized Hamiltonian of nonlinear quantum optical spring and it's solution, we will investigate the nonclassical properties of the obtained states. Specially, typical collapse and revival in the distribution functions and squeezing parameters, as particular quantum features, will be revealed. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Framework for Springs Stewardship Program and proposed action development: Spring Mountains National Recreation Area, Humboldt-Toiyabe National Forest

Science.gov (United States)

Marc Coles-Ritchie; Stephen J. Solem; Abraham E. Springer; Burton Pendleton

2014-01-01

In the desert Southwest, springs are an important ecological feature and serve as a focal point for both biological and human interactions on the landscape. As a result, attention has been placed on the stewardship and protection of these important resources. Management has traditionally focused on the more accessible and heavily used eastern canyons within the Spring...

The saltiest springs in the Sierra Nevada, California

Science.gov (United States)

Moore, James G.; Diggles, Michael F.; Evans, William C.; Klemic, Karin

2017-07-20

The five saltiest springs in the Sierra Nevada in California are found between 38.5° and 38.8° N. latitude, on the South Fork American River; on Caples Creek, a tributary of the Silver Fork American River; and on the North Fork Mokelumne River. The springs issue from Cretaceous granitic rocks in the bottoms of these major canyons, between 1,200- and 2,200-m elevation. All of these springs were well known to Native Americans, who excavated meter-sized basins in the granitic rock, within which they produced salt by evaporation near at least four of the five spring sites. The spring waters are dominated by Cl, Na, and Ca; are enriched relative to seawater in Ca, Li, and As; and are depleted in SO4, Mg, and K. Tritium analyses indicate that the spring waters have had little interaction with rainfall since about 1954. The waters are apparently an old groundwater of meteoric origin that resided at depth before moving up along fractures to the surface of the exhumed granitic rocks. However, along the way these waters incorporated salts from depth, the origin of which could have been either from marine sedimentary rocks intruded by the granitic magmas or from fluid inclusions in the granitic rocks. Prolonged storage at depth fostered water-rock interactions that undoubtedly modified the fluid compositions.

Geochemical studies of Ishiwa hot springs in Yamanashi Prefecture-yearly change of hot springs

Energy Technology Data Exchange (ETDEWEB)

Akiyama, T. (Yamanashi Prefecture Womens Junior College, Japan)

1971-12-01

The effect of drilling on the Ishiwa hot springs was studied. About 50 wells have been drilled since 1961 when the first well was drilled to a depth of 146 m where 47/sup 0/C water flowed at 1376 l/min. Changes have occurred in flow rate, temperature, and chemical composition of the spring water. In area A near the foot of northern Okura-Keijisan along the Byodo and Fuefuki rivers, the pH value was 8.0 to 8.2 when drilling began, but it is now 7.4 to 8.0. In area B in the central spring area along the Chikatsu water reservoir, the pH was about 8.5 when drilling began, but is presently 10. The shift of area A pH to acidic is thought to be due to the effect of river water. The shift in area B pH to alkaline was thought to be connected to the fountainhead with pH 10 which appeared in the Kami-Ogihara Resseki district in Shioyama City. The fountainhead was located along the Fuefuki River at the foot of Obosatsu, 20 km from the Ishiwa area.

Rooster Springs Elementary Teams Up for Success

Science.gov (United States)

Edwards, Jennifer

2012-01-01

For many schools, membership in PTA can become "expected," instead of being a positive, fun opportunity to involve parents and support students and teachers. With more than 800 students each year, Rooster Springs Elementary PTA (RSE PTA) in Dripping Springs, Texas, never worried about membership recruitment. The PTA often assumed that…

Laurel Springs & DoDEA

National Research Council Canada - National Science Library

Jhung, Seung

2000-01-01

At the request of the client organization, Laurel Springs School, we developed an in-depth market analysis of comparable educational programs offered within the Department of Defense Education Activities (DoDEA...

Cyanobacteria in ambient springs

Czech Academy of Sciences Publication Activity Database

Cantonati, M.; Komárek, Jiří; Montejano, G.

2015-01-01

Roč. 24, č. 4 (2015), s. 865-888 ISSN 0960-3115 Institutional support: RVO:67985939 Keywords : Springs * Cyanoprokaryotes * Radiation * Nitrogen Subject RIV: EF - Botanics Impact factor: 2.258, year: 2015

Winter chilling speeds spring development of temperate butterflies.

Science.gov (United States)

Stålhandske, Sandra; Gotthard, Karl; Leimar, Olof

2017-07-01

Understanding and predicting phenology has become more important with ongoing climate change and has brought about great research efforts in the recent decades. The majority of studies examining spring phenology of insects have focussed on the effects of spring temperatures alone. Here we use citizen-collected observation data to show that winter cold duration, in addition to spring temperature, can affect the spring emergence of butterflies. Using spatial mixed models, we disentangle the effects of climate variables and reveal impacts of both spring and winter conditions for five butterfly species that overwinter as pupae across the UK, with data from 1976 to 2013 and one butterfly species in Sweden, with data from 2001 to 2013. Warmer springs lead to earlier emergence in all species and milder winters lead to statistically significant delays in three of the five investigated species. We also find that the delaying effect of winter warmth has become more pronounced in the last decade, during which time winter durations have become shorter. For one of the studied species, Anthocharis cardamines (orange tip butterfly), we also make use of parameters determined from previous experiments on pupal development to model the spring phenology. Using daily temperatures in the UK and Sweden, we show that recent variation in spring temperature corresponds to 10-15 day changes in emergence time over UK and Sweden, whereas variation in winter duration corresponds to 20 days variation in the south of the UK versus only 3 days in the south of Sweden. In summary, we show that short winters delay phenology. The effect is most prominent in areas with particularly mild winters, emphasising the importance of winter for the response of ectothermic animals to climate change. With climate change, these effects may become even stronger and apply also at higher latitudes. © 2017 The Authors. Journal of Animal Ecology © 2017 British Ecological Society.

Analysis of Damped Mass-Spring Systems for Sound Synthesis

Directory of Open Access Journals (Sweden)

Don Morgan

2009-01-01

Full Text Available There are many ways of synthesizing sound on a computer. The method that we consider, called a mass-spring system, synthesizes sound by simulating the vibrations of a network of interconnected masses, springs, and dampers. Numerical methods are required to approximate the differential equation of a mass-spring system. The standard numerical method used in implementing mass-spring systems for use in sound synthesis is the symplectic Euler method. Implementers and users of mass-spring systems should be aware of the limitations of the numerical methods used; in particular we are interested in the stability and accuracy of the numerical methods used. We present an analysis of the symplectic Euler method that shows the conditions under which the method is stable and the accuracy of the decay rates and frequencies of the sounds produced.

Siliceous Shrubs in Yellowstone's Hot Springs: Implications for Exobiological Investigations

Science.gov (United States)

Guidry, S. A.; Chafetz, H. S.

2003-01-01

Potential relict hot springs have been identified on Mars and, using the Earth as an analog, Martian hot springs are postulated to be an optimal locality for recognizing preserved evidence of extraterrestrial life. Distinctive organic and inorganic biomarkers are necessary to recognize preserved evidence of life in terrestrial and extraterrestrial hot spring accumulations. Hot springs in Yellowstone National Park, Wyoming, U.S.A., contain a wealth of information about primitive microbial life and associated biosignatures that may be useful for future exobiological investigations. Numerous siliceous hot springs in Yellowstone contain abundant, centimeter-scale, spinose precipitates of opaline silica (opal-A). Although areally extensive in siliceous hot spring discharge channel facies, these spinose forms have largely escaped attention. These precipitates referred to as shrubs, consist of porous aggregates of spinose opaline silica that superficially resemble miniature woody plants, i.e., the term shrubs. Shrubs in carbonate precipitating systems have received considerable attention, and represent naturally occurring biotically induced precipitates. As such, shrubs have great potential as hot spring environmental indicators and, more importantly, proxies for pre-existing microbial life.

Beamlines on the SPring-8 project

Energy Technology Data Exchange (ETDEWEB)

Ohno, Hideo [Japan Atomic Energy Research Inst., Kamigori, Hyogo (Japan). Kansai Research Establishment

1997-03-01

SPring-8 project is going to construct a ultrahigh-brilliance X-ray synchrotron radiation facility and commissioning of the storage ring is expected in Spring 1977. The facility will be available to scientists and engineers of universities, national laboratories and industries not only from Japan but also from abroad. 20 proposals for public beamlines are submitted to the Beamline Committee and the ten public beamlines are scheduled for completion by the end of 1997. (author)

Instant Spring for Android starter

CERN Document Server

Dahanne, Anthony

2013-01-01

Packt Instant Starter: get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks.This is a Starter which gives you an introduction to Spring for Android with plenty of well-explained practical code examples.If you are an Android developer who wants to learn about RESTful web services and OAuth authentication and authorization, and you also want to know how to speed up your development involving those architectures using Spring for Android abstractions, then this book is for you.But core Java developers

Fast Times During Spring Breaks: Are Traffic Fatalities Another Consequence?

OpenAIRE

French, Michael; Gumus, Gulcin

2014-01-01

Every year in the United States, millions of college students travel for spring break, spending billions of dollars. We examine a potential adverse consequence of spring break that has received little attention in the literature - traffic safety. In particular, we estimate the impact of spring break season on fatal passenger vehicle crashes. Using daily county-level longitudinal data on traffic fatalities in popular spring break destinations from 1982-2011, we conduct separate analyses by age...

Learning Spring application development

CERN Document Server

Soni, Ravi Kant

2015-01-01

This book is intended for those who are interested in learning the core features of the Spring Framework. Prior knowledge of Java programming and web development concepts with basic XML knowledge is expected.

Yakima River Spring Chinook Enhancement Study, 1991 Final Report.

Energy Technology Data Exchange (ETDEWEB)

Fast, David E.

1991-05-01

The population of Yakima River spring chinook salmon (Oncorhynchus tschawytscha) has been drastically reduced from historic levels reported to be as high as 250,000 adults (Smoker 1956). This reduction is the result of a series of problems including mainstem Columbia dams, dams within the Yakima itself, severely reduced flows due to irrigation diversions, outmigrant loss in irrigation canals, increased thermal and sediment loading, and overfishing. Despite these problems, the return of spring chinook to the Yakima River has continued at levels ranging from 854 to 9,442 adults since 1958. In October 1982, the Bonneville Power Administration contracted the Yakima Indian Nation to develop methods to increase production of spring chinook in the Yakima system. The Yakima Nation's current enhancement policy attempts to maintain the genetic integrity of the spring chinook stock native to the Yakima Basin. Relatively small numbers of hatchery fish have been released into the basin in past years. The goal of this study was to develop data that will be used to present management alternatives for Yakima River spring chinook. A major objective of this study is to determine the distribution, abundance and survival of wild Yakima River spring chinook. The second major objective of this study is to determine the relative effectiveness of different methods of hatchery supplementation. The last three major objectives of the study are to locate and define areas in the watershed that may be used for the rearing of spring chinook; to define strategies for enhancing natural production of spring chinook in the Yakima River; and to determine the physical and biological limitations on production within the system. 47 refs., 89 figs., 67 tabs.

Indoor radon levels in selected hot spring hotels in Guangdong, China.

Science.gov (United States)

Song, Gang; Zhang, Boyou; Wang, Xinming; Gong, Jingping; Chan, Daniel; Bernett, John; Lee, S C

2005-03-01

Guangdong is one of the provinces that have most hot springs in China, and many hotels have been set up near hot springs, with spring water introduced into the bath inside each hotel room for hot spring bathing to attract tourists. In the present study, we measured radon in indoor and outdoor air, as well as in hot spring waters, in four hot spring hotels in Guangdong by using NR-667A (III) continuous radon detector. Radon concentrations ranged 53.4-292.5 Bq L(-1) in the hot spring water and 17.2-190.9 Bq m(-3) in outdoor air. Soil gas intrusion, indoor hot spring water use and inefficient ventilation all contributed to the elevated indoor radon levels in the hotel rooms. From the variation of radon levels in closed unoccupied hotel rooms, soil gas intrusion was found to be a very important source of indoor radon in hotel rooms with floors in contact with soils. When there was spring water bathing in the bathes, average radon levels were 10.9-813% higher in the hotel rooms and 13.8-489% higher in bathes compared to their corresponding average levels when there was no spring water use. Spring water use in the hotel rooms had radon transfer coefficients from 1.6x10(-4) to 5.0x10(-3). Radon in some hotel rooms maintained in concentrations much higher than guideline levels might thus have potential health risks to the hotel workers, and technical and management measures should be taken to lower their exposure of radon through inhalation.

Indoor radon levels in selected hot spring hotels in Guangdong, China

International Nuclear Information System (INIS)

Song Gang; Zhang Boyou; Wang Xinming; Gong Jingping; Chan, Daniel; Bernett, John; Lee, S.C.

2005-01-01

Guangdong is one of the provinces that have most hot springs in China, and many hotels have been set up near hot springs, with spring water introduced into the bath inside each hotel room for hot spring bathing to attract tourists. In the present study, we measured radon in indoor and outdoor air, as well as in hot spring waters, in four hot spring hotels in Guangdong by using NR-667A (III) continuous radon detector. Radon concentrations ranged 53.4-292.5 Bq L -1 in the hot spring water and 17.2-190.9 Bq m -3 in outdoor air. Soil gas intrusion, indoor hot spring water use and inefficient ventilation all contributed to the elevated indoor radon levels in the hotel rooms. From the variation of radon levels in closed unoccupied hotel rooms, soil gas intrusion was found to be a very important source of indoor radon in hotel rooms with floors in contact with soils. When there was spring water bathing in the bathes, average radon levels were 10.9-813% higher in the hotel rooms and 13.8-489% higher in bathes compared to their corresponding average levels when there was no spring water use. Spring water use in the hotel rooms had radon transfer coefficients from 1.6x10 -4 to 5.0x10 -3 . Radon in some hotel rooms maintained in concentrations much higher than guideline levels might thus have potential health risks to the hotel workers, and technical and management measures should be taken to lower their exposure of radon through inhalation

Archaeal diversity in Icelandic hot springs

DEFF Research Database (Denmark)

Kvist, Thomas; Ahring, Birgitte Kiær; Westermann, Peter

2007-01-01

Whole-cell density gradient extractions from three solfataras (pH 2.5) ranging in temperature from 81 to 90 degrees C and one neutral hot spring (81 degrees C, pH 7) from the thermal active area of Hveragerethi (Iceland) were analysed for genetic diversity and local geographical variation...... of Archaea by analysis of amplified 16S rRNA genes. In addition to the three solfataras and the neutral hot spring, 10 soil samples in transects of the soil adjacent to the solfataras were analysed using terminal restriction fragment length polymorphism (t-RFLP). The sequence data from the clone libraries...... enzymes AluI and BsuRI. The sequenced clones from this solfatara belonged to Sulfolobales, Thermoproteales or were most closest related to sequences from uncultured Archaea. Sequences related to group I.1b were not found in the neutral hot spring or the hyperthermophilic solfatara (90 degrees C)....

Simulation and analysis of tape spring for deployed space structures

Science.gov (United States)

Chang, Wei; Cao, DongJing; Lian, MinLong

2018-03-01

The tape spring belongs to the configuration of ringent cylinder shell, and the mechanical properties of the structure are significantly affected by the change of geometrical parameters. There are few studies on the influence of geometrical parameters on the mechanical properties of the tape spring. The bending process of the single tape spring was simulated based on simulation software. The variations of critical moment, unfolding moment, and maximum strain energy in the bending process were investigated, and the effects of different radius angles of section and thickness and length on driving capability of the simple tape spring was studied by using these parameters. Results show that the driving capability and resisting disturbance capacity grow with the increase of radius angle of section in the bending process of the single tape spring. On the other hand, these capabilities decrease with increasing length of the single tape spring. In the end, the driving capability and resisting disturbance capacity grow with the increase of thickness in the bending process of the single tape spring. The research has a certain reference value for improving the kinematic accuracy and reliability of deployable structures.

Experimental investigation and modeling of dynamic performance of wave springs

OpenAIRE

Tang, N.; Rongong, J.; Lord, C.; Sims, N.

2016-01-01

This paper investigates vibration suppression potentials for a novel frictional system - a wave spring.\\ud Two different types of wave springs, crest-to-crest and nested ones, were used in this work. Compared with\\ud nested wave springs, crest-to-crest wave springs have lower damping and a larger range for the linear stiffness\\ud due to a reduced level of contact. Dynamic compressive tests, subject to different static compression levels,\\ud are carried out to investigate the force-displacemen...

Spring Bird Migration Phenology in Eilat, Israel

Directory of Open Access Journals (Sweden)

Reuven Yosef

2009-12-01

Full Text Available Analysis of the mean date of first captures and median arrival dates of spring migration for 34 species of birds at Eilat, Israel, revealed that the earlier a species migrates through Eilat, the greater is the inter-annual variation in the total time of its passage. Birds arrive during spring migration in Eilat in four structured and independent waves. The annual fluctuation in the initial arrival dates (initial capture dates and median dates (median date of all captures, not including recaptures, did not depend on the length of the migratory route. This implies that migrants crossing the Sahara desert depart from their winter quarters on different Julian days in different years. We suggest that negative correlations between the median date of the spring migration of early and late migrants depends upon the easterly (Hamsin wind period. Moreover, we believe that the phenology of all birds during spring migration in Eilat is possibly also determined by external factors such as weather conditions on the African continent or global climatic processes in the Northern hemisphere. Orphean Warblers (Sylvia hortensis show a strong positive correlation (rs=-0.502 of initial capture date with calendar years, whereas other species such as Barred Warbler (S. nisoria; rs = -0.391 and Spotted Flycatcher (Muscicapa striata; rs = -0.398 display an insignificant trend. The Dead Sea Sparrow (Passer moabiticus and Red-Backed Shrike (Lanius collurio are positively correlated regarding initial arrival date and medians of spring migration.

New bathing therapy in Japanese hot springs using radiation from radon

International Nuclear Information System (INIS)

Sugimori, Kenji; Okajima, Maiko; Oowada, Mizuno; Koyama, Yoshihisa; Shozugawa, Katsumi; Matsuo, Motoyuki

2015-01-01

Japanese-style bathing is an important part of the traditional culture of Japan, and most Japanese people love hot springs. Many kinds of hot springs exist all over Japan and are often a major factor when considering where to go for travel, relaxation and rest. However, other countries, especially in Europe, also use hot springs for medical treatments such as balneo therapy, hydrokinetic therapy, fango therapy and inhalation therapy. Some hot springs in Japan are located on radioactive springs. Five typical radioactive spring areas can be found in Tamagawa (Akita Pref.), Murasugi (Niigata Pref.), Masutomi (Yamanashi Pref.), Misasa (Tottori Pref.), and Sekigane (Tottori Pref.). While hot springs in Japan are mainly used for bathing, these radioactive springs are also used for bedrock bathing and/or inhalation therapy. In Italy, Fango therapy is a medical treatment conducted under a medical doctor's super vision with peloids maturated with hot spring water called 'Fango'. Japanese style Fango, named Biofango R , has already been made by using natural hot springs that have been modified with Italian Fango. Medical evaluation of test subjects has shown good results after treatment with Fango therapy. An important point in Fango therapy is how to make satisfactory maturated peloids. For this purpose, an experiment was conducted at Masutomi hot spring to confirm the possibility of using radioactive spring water to make maturated peloids. The basement material for the peloids used for this experiment was made from bentonite mixed with original rock from the Masutomi hot spring area consisting of crushed basalt and granite that have a fine amount of radioactivity. These peloids were circulated through hot spring water for two weeks to a month and then used for treatment. The medical data showed that therapy using this method resulted in greater improvement in 'test subjects' body functions compared with the data from previous observations. This

The Hydrogeological investigation of Plajköy spring (Elazığ

Directory of Open Access Journals (Sweden)

Özlem ÖZTEKİN OKAN

2018-01-01

Full Text Available Plajköy spring discharges at the close locations to the SE shore of Lake Hazar. Lake Hazar is a tectonic Lake in Elazığ city. Plajköy spring is a fault spring that is mainly recharging from the volcanites, dikes and blocky volcanosedimentary units of Middle Eocene Maden Complex. These units have gained secondary permeability and porosity related with the active tectonics that is effective in the studied area. The present catchment system of the spring could not collect the springs and leaks discharging from different points around the system. The discharge of the catchment is measured by specifi c volume method while the other springs’ and leaks’ is measured by using triangular weir. Before the discharge measurement of the leaks and the springs, they have been directed to a channel. The discharge of the present catchment system and the leaks have measured twice in a month during one year period beginning from October of 2012 to November of 2013. The discharge coeffi cient of the spring is calculated 1.33*10-3 day-1. Discharge coeffi cient of the spring depends on the geometry and intensity of the active fracture systems in the region. Calculated discharge coeffi cient indicates that the spring discharge is related with the narrow fi ssures, fractures and pores. The total volume of discharged groundwater in the real regime of the Plajköy spring is calculated as 52* 103 m3 during the period from 31st of March, 2013 to the 13rd of October, 2013 by Maillet formula. The spring water is Ca- Mg- HCO3 type water related with the chemical analyses. The chemical and microbiological analyses of the spring water are correlated with the drinking water standarts of Turkey TS 266 (TSE, 2005 and World Health Organization (2004, and it is seen that the spring water is suitable for drinking. The Plajköy spring will be used more effi ciently without exposed to pollution by the new catchment plan and protection zone map that are consequently proposed in

Spring Bottom Trawl Survey

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The standardized NEFSC Spring Bottom Trawl Survey was initiated in 1968 and covered an area from Cape Hatteras, NC, to Nova Scotia, Canada, at depths >27m....

Impacts of climate change on spring flower tourism in Beijing, China

Science.gov (United States)

Wang, Huanjiong

2016-04-01

The beauty of blooming flowers causes spring to be one of the most picturesque and pleasant seasons in which to travel. However, the blooming time of plant species are very sensitive to small changes in climate. Therefore, recent climate change may shift flowering time and, as a result, may affect timing of spring tourism for tourists. In order to prove this assumption, we gathered data of first flowering date and end of flowering date (1963-2014) for 49 common ornamental plants in Beijing, China. In addition, we used the number of messages (2010-2014) posted on Sina Weibo (one of the most popular microblogs sites in China, in use by well over 30% of internet users, with a market penetration similar to the United States' Twitter) to indicate the tourist numbers of five scenic spots in Beijing. These spots are most famous places for seeing spring flowers, including the Summer Palace, Yuyuantan Park, Beijing Botanical Garden, Jingshan Park, Dadu City Wall Relics Park. The results showed that the number of species in flower starts to increase in early spring and peaks in middle spring, and then begins to decrease from late spring. The date when the number of species in flower peaks can be defined as best date of spring flower tourism, because on this day people can see blooming flowers of most plant species. The best date of spring flower tourism varied from March 31 to May 1 among years with a mean of April 20. At above scenic spots characterized by the beauty of blooming flowers, tourist numbers also had a peak value during spring. Furthermore, peak time of tourist numbers derived from Weibo varied among different years and was related to best date of spring flower tour derived from phenological data. This suggests that the time of spring outing for tourists is remarkably attracted by flowering phenology. From 1963 to 2014, the best date of spring flower tour became earlier at a rate of 1.6 days decade-1, but the duration for spring flower tour (defined as width at

Preliminary analysis of geothermal aspects of Brazilian thermal spring

International Nuclear Information System (INIS)

Hurter, S.J.; Hamza, V.M.

1982-01-01

Information on more than 400 geothermal springs in Brazil has been assembled. On the basis of the data colected the temperatures at the maximum depths of circulation of spring waters are calculated using the quality of silica dissolved in water. For some thermal springs temperatures are calculated on the basis of silica determination carrried out by us. Applying linear relations between silica temperature and geothermal flux the average depths of water circulation in the Parana Basin and the Brazilian folded belts surrounding the San Francisco craton are calculated. The radioactivity of the water, derived mainly from the dissolved radon can be correlated with the temperature of the spring. An inverse correlation, as was observed for thermal springs of Pocos de Caldas, can be used to calculate the ascent velocity of thermal waters, where as, a positive correlations could be interpreted as due to the mixing of thermal with surface waters. (Author) [pt

Diversity of Bamboos around springs in Malang East Java

Directory of Open Access Journals (Sweden)

Solikin Solikin

2014-11-01

Full Text Available Bamboos have important roles to people in the villages area. They are planted and used by the people for making houses, food, buckets, fences, ropes, fuels, musical instruments and plaits. The root distribution of Bamboos is large and fibrous, also the growth of their new clumps is ascendant so the Bamboos has good potency for water and soil conservation on river banks, around the springs, hillsides and scarps. The survey to invent the bamboos growing around the springs was conducted in Singosari, Lawang, Karangploso, Dau and Lowokwaru Malang East Java in May 2009. The Bamboos invented at 0-100 m from the springs. The results Showed that there were four Bamboos founded around the springs namely Bambusa blumeana,Dendrocalamus asper, Gigantochloa atter and Gigantochloa apus. Dendrocalamus asper was the most dominant species founded around the springs with relative frequency, relative density and important value index is 45.83 ; 58.49 and 104.32 respectively.

Indoor radon levels in selected hot spring hotels in Guangdong, China

Energy Technology Data Exchange (ETDEWEB)

Song Gang [Guangzhou Institute of Geochemistry, Chinese Academy of Science, Guangzhou 510640 (China); Zhang Boyou [Guangzhou Institute of Geochemistry, Chinese Academy of Science, Guangzhou 510640 (China); Wang Xinming [Guangzhou Institute of Geochemistry, Chinese Academy of Science, Guangzhou 510640 (China)]. E-mail: wangxm@gig.ac.cn; Gong Jingping [Guangzhou Institute of Geochemistry, Chinese Academy of Science, Guangzhou 510640 (China); Chan, Daniel [Department of Building Services Engineering, Hong Kong Polytechnic University, Hong Kong (China); Bernett, John [Department of Building Services Engineering, Hong Kong Polytechnic University, Hong Kong (China); Lee, S.C. [Department of Civil and Structural Engineering, Hong Kong Polytechnic University, Hong Kong (China)

2005-03-01

Guangdong is one of the provinces that have most hot springs in China, and many hotels have been set up near hot springs, with spring water introduced into the bath inside each hotel room for hot spring bathing to attract tourists. In the present study, we measured radon in indoor and outdoor air, as well as in hot spring waters, in four hot spring hotels in Guangdong by using NR-667A (III) continuous radon detector. Radon concentrations ranged 53.4-292.5 Bq L{sup -1} in the hot spring water and 17.2-190.9 Bq m{sup -3} in outdoor air. Soil gas intrusion, indoor hot spring water use and inefficient ventilation all contributed to the elevated indoor radon levels in the hotel rooms. From the variation of radon levels in closed unoccupied hotel rooms, soil gas intrusion was found to be a very important source of indoor radon in hotel rooms with floors in contact with soils. When there was spring water bathing in the bathes, average radon levels were 10.9-813% higher in the hotel rooms and 13.8-489% higher in bathes compared to their corresponding average levels when there was no spring water use. Spring water use in the hotel rooms had radon transfer coefficients from 1.6x10{sup -4} to 5.0x10{sup -3}. Radon in some hotel rooms maintained in concentrations much higher than guideline levels might thus have potential health risks to the hotel workers, and technical and management measures should be taken to lower their exposure of radon through inhalation.

Distribution of glycerol dialkyl glycerol tetraethers in Tibetan hot springs

Directory of Open Access Journals (Sweden)

Liu He

2012-05-01

Full Text Available Isoprenoidal glycerol dialkyl glycerol tetraethers (iGDGTs from the Gulu hot springs (23–83.6 °C, pH > 7 and Yangbajing hot springs (80–128 °C, pH > 7 were analyzed in order to investigate the distribution of archaeal lipids among different hot springs in Tibet. A soil sample from Gulu was incubated at different temperatures and analyzed for changes in iGDGTs to help evaluate whether surrounding soil may contribute to the iGDGTs in hot springs. The sources of bacterial GDGTs (bGDGTs in these hot springs were also investigated. The results revealed different profiles of iGDGTs between Gulu and Yangbajing hot springs. Core iGDGTs and polar iGDGTs also presented different patterns in each hot spring. The PCA analysis showed that the structure of polar iGDGTs can be explained by three factors and suggested multiple sources of these compounds. Bivariate correlation analysis showed significant positive correlations between polar and core bGDGTs, suggesting the in situ production of bGDGTs in the hot springs. Furthermore, in the soil incubation experiment, temperature had the most significant influence on concentration of bGDGTs rather than iGDGTs, and polar bGDGTs had greater variability than core bGDGTs with changing temperature. Our results indicated that soil input had little influence on the composition of GDGTs in Tibetan hot springs. On the other hand, ring index and TEX86 values were both positively correlated with incubation temperature, suggesting that the structure of archaeal lipids changed in response to varying temperature during incubation.

Synergy of a warm spring and dry summer

Science.gov (United States)

Yude Pan; David. Schimel

2016-01-01

An analysis suggests that high carbon uptake by US land ecosystems during the warm spring of 2012 offset the carbon loss that resulted from severe drought over the summer — and hints that the warm spring could have worsened the drought.

Nonlinear Squeeze Film Dampers without Centralized Springs

Directory of Open Access Journals (Sweden)

Zhu Changsheng

2000-01-01

Full Text Available In this paper, the bifurcation behavior of a flexible rotor supported on nonlinear squeeze film dampers without centralized springs is analyzed numerically by means of rotor trajectories, Poincar maps, bifurcation diagrams and power spectra, based on the short bearing and cavitated film assumptions. It is shown that there also exist two different operations (i.e., socalled bistable operations in some speed regions in the rotor system supported on the nonlinear squeeze film dampers without centralized springs. In the bistable operation speed regions, the rotor system exhibits synchronous, sub-synchronous, sub-super-synchronous and almost-periodic as well as nonperiodic motions. The periodic bifurcation behaviors of the rotor system supported on nonlinear squeeze film dampers without centralized springs are very complex and require further investigations.

Depositional facies and aqueous-solid geochemistry of travertine-depositing hot springs (Angel Terrace, Mammoth Hot Springs, Yellowstone National Park, USA)

Energy Technology Data Exchange (ETDEWEB)

Fouke, B.W.; Farmer, J.D.; Des Marais, D.J.; Pratt, L.; Sturchio, N.C.; Burns, P.C.; Discipulo, M.K.

2000-05-01

Petrographic and geochemical analyses of travertine-depositing hot springs at Angel Terrace, Mammoth Hot Springs, Yellowstone National Park, have been used to define five depositional facies along the spring drainage system. Spring waters are expelled in the vent facies at 71 to 73 C and precipitate mounded travertine composed of aragonite needle botryoids. The apron and channel facies (43--72 C) is floored by hollow tubes composed of aragonite needle botryoids that encrust sulfide-oxidizing Aquificales bacteria. The travertine of the pond facies (30--62 C) varies in composition from aragonite needle shrubs formed at higher temperatures to ridged networks of calcite and aragonite at lower temperatures. Calcite ice sheets, calcified bubbles, and aggregates of aragonite needles (fuzzy dumbbells) precipitate at the air-water interface and settle to pond floors. The proximal-slope facies (28--54 C), which forms the margins of terracette pools, is composed of arcuate aragonite needle shrubs that create small microterracettes on the steep slope face. Finally, the distal-slope facies (28--30 C) is composed of calcite spherules and calcite feather crystals. Despite the presence of abundant microbial mat communities and their observed role in providing substrates for mineralization, the compositions of spring-water and travertine predominantly reflect abiotic physical and chemical processes. Vigorous CO{sub 2} degassing causes a +2 unit increase in spring water pH, as well as Rayleigh-type covariations between the concentration of dissolved inorganic carbon and corresponding {delta}{sup 13}C. Travertine {delta}{sup 13}C and {delta}{sup 18}O are nearly equivalent to aragonite and calcite equilibrium values calculated from spring water in the higher-temperature ({approximately}50--73 C) depositional facies. Conversely, travertine precipitating in the lower-temperature (<{approximately}50 C) depositional facies exhibits {delta}{sup 13}C and {delta}{sup 18}O values that are as

Spring batch essentials

CERN Document Server

Rao, P Raja Malleswara

2015-01-01

If you are a Java developer with basic knowledge of Spring and some experience in the development of enterprise applications, and want to learn about batch application development in detail, then this book is ideal for you. This book will be perfect as your next step towards building simple yet powerful batch applications on a Java-based platform.

Wavelength variation of a standing wave along a vertical spring

Science.gov (United States)

Welsch, Dylan; Baker, Blane

2018-03-01

Hand-driven resonance can be observed readily in a number of mechanical systems including thin boards, rods, strings, and springs. In order to show such behavior in the vertical spring pictured in Fig. 1, a section of spring is grasped at a location about one meter from its free end and driven by small, circular motions of the hand. At driving frequencies of a few hertz, a dramatic standing wave is generated. One of the fascinating features of this particular standing wave is that its wavelength varies along the length of the spring.

Multiscale Mass-Spring Models of Carbon Nanotube Foams

Science.gov (United States)

2010-09-06

Rev. 8-98) Prescribed by ANSI Std Z39-18 Graphical abstract (movie) Axial strain localization in a mesoscopic chain of five bistable springs. The...line). Graphical Abstract Research highlights • Axial strain localization in microscopic bistable spring chains mimics kink- ing of compressed carbon

Effects of springs on a pendulum electromechanical energy harvester

OpenAIRE

Arnaud Notué Kadjie; Paul Woafo

2014-01-01

This paper studies a model of energy harvester that consists of an electromechanical pendulum system subjected to nonlinear springs. The output power is analyzed in terms of the intrinsic parameters of the device leading to optimal parameters for energy harvesting. It is found that in an appropriate range of the springs constant, the power attains higher values as compared to the case without springs. The dynamical behavior of the device shows transition to chaos.

Characterization of closed nickel-titanium orthodontic coil springs

Energy Technology Data Exchange (ETDEWEB)

Langeron, T. [Rene Descartes Univ., Paris V, Pontoise (France). Faculte de Chirurgie Dentaire; Filleul, M.P. [Rene Descartes Univ., Paris V, Pontoise (France). Faculte de Chirurgie Dentaire; ENSCP, Paris (France). Lab. de Metallurgie Structurale; Humbeeck, J. van [Katholieke Univ. Leuven, Heverlee (Belgium). Faculteit Toegepaste Wetenschappen, Metaalkunde en Toegepaste Materialkund

2001-11-01

Nickel-titanium orthodontic coil springs are used to move teeth with low forces and slow deactivation. The present paper provides data on transformation temperatures and on load-deflection rate at buccal temperature of closed Nickel-Titanium coil springs available on the market from ORMCO {sup trademark} and GAC {sup trademark}. All the springs exhibited superelasticity but their properties were not stable in the range of buccal temperatures and varied not only from one manufacturer to the other but they also varied from one batch to the other of each supplier. The need for more stability is stressed. (orig.)

Climate-induced warming imposes a threat to north European spring ecosystems.

Science.gov (United States)

Jyväsjärvi, Jussi; Marttila, Hannu; Rossi, Pekka M; Ala-Aho, Pertti; Olofsson, Bo; Nisell, Jakob; Backman, Birgitta; Ilmonen, Jari; Virtanen, Risto; Paasivirta, Lauri; Britschgi, Ritva; Kløve, Bjørn; Muotka, Timo

2015-12-01

Interest in climate change effects on groundwater has increased dramatically during the last decade. The mechanisms of climate-related groundwater depletion have been thoroughly reviewed, but the influence of global warming on groundwater-dependent ecosystems (GDEs) remains poorly known. Here we report long-term water temperature trends in 66 northern European cold-water springs. A vast majority of the springs (82%) exhibited a significant increase in water temperature during 1968-2012. Mean spring water temperatures were closely related to regional air temperature and global radiative forcing of the corresponding year. Based on three alternative climate scenarios representing low (RCP2.6), intermediate (RCP6) and high-emission scenarios (RCP8.5), we estimate that increase in mean spring water temperature in the region is likely to range from 0.67 °C (RCP2.6) to 5.94 °C (RCP8.5) by 2086. According to the worst-case scenario, water temperature of these originally cold-water ecosystems (regional mean in the late 1970s: 4.7 °C) may exceed 12 °C by the end of this century. We used bryophyte and macroinvertebrate species data from Finnish springs and spring-fed streams to assess ecological impacts of the predicted warming. An increase in spring water temperature by several degrees will likely have substantial biodiversity impacts, causing regional extinction of native, cold-stenothermal spring specialists, whereas species diversity of headwater generalists is likely to increase. Even a slight (by 1 °C) increase in water temperature may eliminate endemic spring species, thus altering bryophyte and macroinvertebrate assemblages of spring-fed streams. Climate change-induced warming of northern regions may thus alter species composition of the spring biota and cause regional homogenization of biodiversity in headwater ecosystems. © 2015 John Wiley & Sons Ltd.

The role of risk assessment in project planning at the Weldon Spring Quarry, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Haroun, L.A.; Peterson, J.M.

1989-01-01

This paper presents the methodology used to prepare a baseline risk evaluation of the bulk wastes at the quarry. The DOE is proposing to remove these bulk wastes and transport them approximately 6.4 km (4 mi) to a temporary storage facility at the chemical plant area of the Weldon Spring site. The DOE has responsibility for cleanup activities at the Weldon Spring site under its Surplus Facilities Management Program (SFMP). A baseline risk evaluation is an evaluation of the potential impacts on human health and the environment that may result from exposure to releases of contaminants from a site in the absence of site remediation. This evaluation is a key component of the remedial investigation (RI) process, as identified in guidance from the US Environmental Protection Agency (EPA) that addresses sites subject to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980, as amended by the Superfund Amendments and Reauthorization Act of 1986. Response actions at the Weldon Spring quarry are subject to CERCLA requirements because the quarry is listed on the EPA's National Priorities List

Patterns of Macroinvertebrate and Fish Diversity in Freshwater Sulphide Springs

Directory of Open Access Journals (Sweden)

Ryan Greenway

2014-09-01

Full Text Available Extreme environments are characterised by the presence of physicochemical stressors and provide unique study systems to address problems in evolutionary ecology research. Sulphide springs provide an example of extreme freshwater environments; because hydrogen sulphide’s adverse physiological effects induce mortality in metazoans even at micromolar concentrations. Sulphide springs occur worldwide, but while microbial communities in sulphide springs have received broad attention, little is known about macroinvertebrates and fish inhabiting these toxic environments. We reviewed qualitative occurrence records of sulphide spring faunas on a global scale and present a quantitative case study comparing diversity patterns in sulphidic and adjacent non-sulphidic habitats across replicated river drainages in Southern Mexico. While detailed studies in most regions of the world remain scarce, available data suggests that sulphide spring faunas are characterised by low species richness. Dipterans (among macroinvertebrates and cyprinodontiforms (among fishes appear to dominate the communities in these habitats. At least in fish, there is evidence for the presence of highly endemic species and populations exclusively inhabiting sulphide springs. We provide a detailed discussion of traits that might predispose certain taxonomic groups to colonize sulphide springs, how colonizers subsequently adapt to cope with sulphide toxicity, and how adaptation may be linked to speciation processes.

Hydrology and geochemistry of carbonate springs in Mantua Valley, northern Utah

Science.gov (United States)

Rice, Karen C.; Spangler, Lawrence E.; Spangler, Lawrence E.; Allen, Constance J.

1999-01-01

Water chemistry, tritium data, precipitation-discharge relations, geology, topography, and dye tracing were used to determine recharge areas, ground-water residence times, factors influencing ground-water flow, and aquifer characteristic for five springs that discharge from Paleozoic limestones and dolostones along the margin of Manuta Valley, northern Utah.Temperature of Mantua Valley spring water ranged between 6.0 and 15.0 degrees Celsius. Spring-water temperature indicates that depth of circulation of ground water could be as shallow as 80 feet (25 meters) to as much as 1,150 feet (350 meters). Dissolved-solids concentration in the water from springs ranged from 176 to 268 milligrams per liter. Average total hardness of spring water ranged from 157 to 211 milligrams per liter. Water from all of the springs is a calcium-magnesium-bicarbonate type that generally is undersaturated with respect to calcite and dolomite. The molar calcium/magnesium ratio in spring water ranged from 1.21 to 1.88, and indicates that ground water flows through impure dolostone or a mixed limestone and dolostone terrace.Discharge from carbonate springs in Mantua Valley ranges from about to 10 to 4,300 gallons per minute (0.6 to 271 liters per second). Seasonal variations in chemical parameters and discharge indicate that the aquifers supplying water to most of these springs are predominantly diffuse-flow systems that have been locally enhanced by bedrock dissolution. Estimated recharge area for th springs ranges from 2.7 to 7 square miles (7 to 18 square kilometers).On the basis of tritium age dating, the mean residence time of ground water discharges from Olsens-West Hallins and Maple Springs was determined to be from 3 to 9, and from 4 to 15 years, respectively. Dye tracing from point sources 2.65 miles (4.26 kilometers) southeast of Maple Spring, however, indicates a substantially faster component of flow during snowmelt runoff, with a travel time of about 5 days, or an average ground

Evaluation of the cleanness of SiCr-spring steels for suspension springs

Energy Technology Data Exchange (ETDEWEB)

Valentin, P.; Blaesius, A.; Bruch, C. [Saarstahl AG, Voelklingen (Germany)

2005-07-01

The requirements of suspension springs for the automotive industry are increasing with regard to cleanness and strength. In order to meet this high quality level a remarkable quality improvement was obtained within the last years due to the introduction of a very strict ladle metallurgy together with a controlled stirring in ladle and an optimized steel flow pattern in the tundish. The tradition of spring steel and particularly of Si killed SiCr steel grades of the Saarstahl AG increased continuously within the last years and reached nearly 100000 t/a in 2004, at the same time the rejection rate decreased significantly. The application of the soft reduction technique and an advanced equipment on the new billet continuous casting machine SO with a strand size of 150 mm sq. and the introduction of the new walking beam furnace and the precise temperature controlled deformation in the rolling mill will provide further substantial quality improvements. (orig.)

Topology Counts: Force Distributions in Circular Spring Networks

Science.gov (United States)

Heidemann, Knut M.; Sageman-Furnas, Andrew O.; Sharma, Abhinav; Rehfeldt, Florian; Schmidt, Christoph F.; Wardetzky, Max

2018-02-01

Filamentous polymer networks govern the mechanical properties of many biological materials. Force distributions within these networks are typically highly inhomogeneous, and, although the importance of force distributions for structural properties is well recognized, they are far from being understood quantitatively. Using a combination of probabilistic and graph-theoretical techniques, we derive force distributions in a model system consisting of ensembles of random linear spring networks on a circle. We show that characteristic quantities, such as the mean and variance of the force supported by individual springs, can be derived explicitly in terms of only two parameters: (i) average connectivity and (ii) number of nodes. Our analysis shows that a classical mean-field approach fails to capture these characteristic quantities correctly. In contrast, we demonstrate that network topology is a crucial determinant of force distributions in an elastic spring network. Our results for 1D linear spring networks readily generalize to arbitrary dimensions.

Stress corrosion cracking lifetime prediction of spring screw

International Nuclear Information System (INIS)

Koh, S. K.; Ryu, C. H.

2004-01-01

A lifetime prediction of holddown spring screw in nuclear fuel assembly was performed using fracture mechanics approach. The spring screw was designed such that it was capable of sustaining the loads imposed by the initial tensile preload and operational loads. In order to investigate the cause of failure and to predict the stress corrosion cracking life of the screw, a stress analysis of the top nozzle spring assembly was done using finite element analysis. The elastic-plastic finite element analysis showed that the local stresses at the critical regions of head-shank fillet and thread root significantly exceeded than the yield strength of the screw material, resulting in local plastic deformation. Normalized stress intensity factors for PWSCC life prediction was proposed. Primary water stress corrosion cracking life of the Inconel 600 screw was predicted by using integration of the Scott model and resulted in 1.78 years, which was fairly close to the actual service life of the holddown spring screw

Topology Counts: Force Distributions in Circular Spring Networks.

Science.gov (United States)

Heidemann, Knut M; Sageman-Furnas, Andrew O; Sharma, Abhinav; Rehfeldt, Florian; Schmidt, Christoph F; Wardetzky, Max

2018-02-09

Filamentous polymer networks govern the mechanical properties of many biological materials. Force distributions within these networks are typically highly inhomogeneous, and, although the importance of force distributions for structural properties is well recognized, they are far from being understood quantitatively. Using a combination of probabilistic and graph-theoretical techniques, we derive force distributions in a model system consisting of ensembles of random linear spring networks on a circle. We show that characteristic quantities, such as the mean and variance of the force supported by individual springs, can be derived explicitly in terms of only two parameters: (i) average connectivity and (ii) number of nodes. Our analysis shows that a classical mean-field approach fails to capture these characteristic quantities correctly. In contrast, we demonstrate that network topology is a crucial determinant of force distributions in an elastic spring network. Our results for 1D linear spring networks readily generalize to arbitrary dimensions.

Experimental and numerical investigations of shape memory alloy helical springs

International Nuclear Information System (INIS)

Aguiar, Ricardo A A; Pacheco, Pedro M C L; Savi, Marcelo A

2010-01-01

Shape memory alloys (SMAs) belong to the class of smart materials and have been used in numerous applications. Solid phase transformations induced either by stress or temperature are behind the remarkable properties of SMAs that motivate the concept of innovative smart actuators for different purposes. The SMA element used in these actuators can assume different forms and a spring is an element usually employed for this aim. This contribution deals with the modeling, simulation and experimental analysis of SMA helical springs. Basically, a one-dimensional constitutive model is assumed to describe the SMA thermomechanical shear behavior and, afterwards, helical springs are modeled by considering a classical approach for linear-elastic springs. A numerical method based on the operator split technique is developed. SMA helical spring thermomechanical behavior is investigated through experimental tests performed with different thermomechanical loadings. Shape memory and pseudoelastic effects are treated. Numerical simulations show that the model results are in close agreement with those obtained by experimental tests, revealing that the proposed model captures the general thermomechanical behavior of SMA springs

Parsimonious Hydrologic and Nitrate Response Models For Silver Springs, Florida

Science.gov (United States)

Klammler, Harald; Yaquian-Luna, Jose Antonio; Jawitz, James W.; Annable, Michael D.; Hatfield, Kirk

2014-05-01

Silver Springs with an approximate discharge of 25 m3/sec is one of Florida's first magnitude springs and among the largest springs worldwide. Its 2500-km2 springshed overlies the mostly unconfined Upper Floridan Aquifer. The aquifer is approximately 100 m thick and predominantly consists of porous, fractured and cavernous limestone, which leads to excellent surface drainage properties (no major stream network other than Silver Springs run) and complex groundwater flow patterns through both rock matrix and fast conduits. Over the past few decades, discharge from Silver Springs has been observed to slowly but continuously decline, while nitrate concentrations in the spring water have enormously increased from a background level of 0.05 mg/l to over 1 mg/l. In combination with concurrent increases in algae growth and turbidity, for example, and despite an otherwise relatively stable water quality, this has given rise to concerns about the ecological equilibrium in and near the spring run as well as possible impacts on tourism. The purpose of the present work is to elaborate parsimonious lumped parameter models that may be used by resource managers for evaluating the springshed's hydrologic and nitrate transport responses. Instead of attempting to explicitly consider the complex hydrogeologic features of the aquifer in a typically numerical and / or stochastic approach, we use a transfer function approach wherein input signals (i.e., time series of groundwater recharge and nitrate loading) are transformed into output signals (i.e., time series of spring discharge and spring nitrate concentrations) by some linear and time-invariant law. The dynamic response types and parameters are inferred from comparing input and output time series in frequency domain (e.g., after Fourier transformation). Results are converted into impulse (or step) response functions, which describe at what time and to what magnitude a unitary change in input manifests at the output. For the

Chemical and Hydro-Geologic Analysis of Ikogosi Warm Spring Water in Nigeria

OpenAIRE

Akinola Ikudayisi; Folasade Adeyemo; Josiah Adeyemo

2015-01-01

This study focuses on the hydro-geology and chemical constituents analysis of Ikogosi Warm Spring waters in South West Nigeria. Ikogosi warm spring is a global tourist attraction because it has both warm and cold spring sources. Water samples from the cold spring, warm spring and the meeting point were collected, analyzed and the result shows close similarity in temperature, hydrogen iron concentration (pH), alkalinity, hardness, Calcium, Magnesium, Sodium, Iron, total di...

Effects of springs on a pendulum electromechanical energy harvester

Directory of Open Access Journals (Sweden)

Arnaud Notué Kadjie

2014-01-01

Full Text Available This paper studies a model of energy harvester that consists of an electromechanical pendulum system subjected to nonlinear springs. The output power is analyzed in terms of the intrinsic parameters of the device leading to optimal parameters for energy harvesting. It is found that in an appropriate range of the springs constant, the power attains higher values as compared to the case without springs. The dynamical behavior of the device shows transition to chaos.

Response of surface springs to longwall coal mining Wasatch Plateau, Utah

International Nuclear Information System (INIS)

Kadnuck, L.L.M.

1994-01-01

High-extraction longwall coal mining creates zones in the overburden where strata bend, fracture, or cave into the mine void. These physical alterations to the overburden stratigraphy have associated effects on the hydrologic regime. The US Bureau of Mines (SBM) studied impacts to the local hydrologic system caused by longwall mining in the Wasatch Plateau, Utah. Surface springs in the vicinity of two coal mines were evaluated for alterations in flow characteristics as mining progressed. Fourteen springs located above the mines were included in the study. Eight of the springs were located over longwall panels, four were located over barrier pillars and mains, and two ere located outside the area disturbed by mining. Flow hydrographs for each spring were compared to climatic data and time of undermining to assess if mining in the vicinity had influenced flow. Heights of fracturing and caving in the overburden resulting from seam extraction were calculated using common subsidence formulas, and used in conjunction with elevations of springs to assess if fracturing influenced the water-bearing zones studied. One spring over a panel exhibited a departure from a normally-shaped hydrograph after being undermined. Springs located over other mine structures, or outside the mine area did not show discernible effects from mining. The limited response of the springs was attributed to site-specific conditions that buffered mining impacts including the elevation of the springs above the mine level, and presence of massive sandstones and swelling clays in the overburden materials

Delineating the Rattlesnake Springs, New Mexico Watershed Using Precision Gravity Techniques

Science.gov (United States)

Doser, D. I.; Boykov, N. D.; Baker, M. R.; Kaip, G. M.; Langford, R. P.

2009-12-01

Rattlesnake Springs serves as the sole domestic water source for Carlsbad Caverns National Park. The recent development of oil and gas leases and agricultural lands surrounding the springs has led to concern about contamination of the fracture controlled aquifer system. We have conducted a series of precision gravity surveys (station spacing 200 to 300 m in a 4 x 4 km area), combined with other geophysical studies and geologic mapping, to delineate possible fracture systems in the gypsum and carbonate bedrock that feed the spring system. Our combined results suggest several pathways for water to enter the springs. A series of WNW-ESE striking features are apparent in our gravity data that appear to align with relict spring valleys we have mapped to the west of the springs. A self potential survey indicates that water is entering the springs at a shallow level from the northwest direction. However, gravity data also indicate a north-south trending fracture system could be providing a pathway for water to enter from the south. This is consistent with drawdown tests conducted in the 1950’s and 1960’s on irrigation wells located to the south of the springs. The north-south fracture system appears related to a basin bounding fault system observed in the regional gravity data.

In Vivo Force Decay of Niti Closed Coil Springs

Science.gov (United States)

Cox, Crystal; Nguyen, Tung; Koroluk, Lorne; Ko, Ching-Chang

2014-01-01

Introduction Nickel-titanium (NiTi) closed coil springs are purported to deliver constant forces over extended ranges of activation and working times. In vivo studies supporting this claim are limited. The objective of this study is to evaluate changes in force decay properties of NiTi closed coil springs after clinical use. Methods Pseudoelastic force-deflection curves for 30 NiTi coil springs (used intra-orally) and 15 matched laboratory control springs (simulated intra-oral conditions - artificial saliva, 37°C) were tested pre- and post-retrieval via Dynamic Mechanical Analysis (DMA) and the Instron machine, respectively, to evaluate amount of force loss and hysteresis change following 4, 8, or 12 weeks of working time (n=10 per group). Effect of the oral environment and clinical use on force properties were evaluated by comparing in vivo and in vitro data. Results The springs studied showed a statistically significant decrease in force (~12%) following 4 weeks of clinical use (pspace closure at an average rate of 0.91mm per month was still observed despite this decrease in force. In vivo and in vitro force loss data were not statistically different. Conclusions NiTi closed coil springs do not deliver constant forces when used intra-orally, but they still allow for space closure rates of ~1mm/month. PMID:24703289

Springs on the Nevada Test Site and their use by wildlife

International Nuclear Information System (INIS)

Giles, K.R.

1976-04-01

During August 1972, natural springs located on the Nevada Test Site were surveyed to determine the use by wildlife and the effort required for improving flow. Each spring is described and its use by wildlife noted. Methods of improving spring flow are suggested. It is believed that minimal effort at most of the springs would result in a significant improvement of waterflow with resulting benefits to wildlife. The intention of the recommendations in this report is to encourage development of the Nevada Test Site springs and to maintain the wildlife now at the Site. There is no recommendation to bring in or support wildlife outside the Nevada Test Site area

Timescales for nitrate contamination of spring waters, northern Florida, USA

Science.gov (United States)

Katz, B.G.; Böhlke, J.K.; Hornsby, H.D.

2001-01-01

Residence times of groundwater, discharging from springs in the middle Suwannee River Basin, were estimated using chlorofluorocarbons (CFCs), tritium (3H), and tritium/helium-3 (3H/3He) age-dating methods to assess the chronology of nitrate contamination of spring waters in northern Florida. During base-flow conditions for the Suwannee River in 1997–1999, 17 water samples were collected from 12 first, second, and third magnitude springs discharging groundwater from the Upper Floridan aquifer. Extending age-dating techniques, using transient tracers to spring waters in complex karst systems, required an assessment of several models [piston-flow (PFM), exponential mixing (EMM), and binary-mixing (BMM)] to account for different distributions of groundwater age. Multi-tracer analyses of four springs yielded generally concordant PFM ages of around 20±2 years from CFC-12, CFC-113, 3H, and 3He, with evidence of partial CFC-11 degradation. The EMM gave a reasonable fit to CFC-113, CFC-12, and 3H data, but did not reproduce the observed 3He concentrations or 3H/3He ratios, nor did a combination PFM–EMM. The BMM could reproduce most of the multi-tracer data set only if both endmembers had 3H concentrations not much different from modern values. CFC analyses of 14 additional springs yielded apparent PFM ages from about 10 to 20 years from CFC-113, with evidence of partial CFC-11 degradation and variable CFC-12 contamination. While it is not conclusive, with respect to the age distribution within each spring, the data indicate that the average residence times were in the order of 10–20 years and were roughly proportional to spring magnitude. Applying similar models to recharge and discharge of nitrate based on historical nitrogen loading data yielded contrasting trends for Suwanee County and Lafayette County. In Suwanee County, spring nitrate trends and nitrogen isotope data were consistent with a peak in fertilizer input in the 1970s and a relatively high overall ratio

Mechanical characteristic evaluation of the mid grid spring in PWR fuel assembly

International Nuclear Information System (INIS)

Eum, K. B.; Lee, S. H.; Jeon, S. Y.; Kweon, Y. B.; Jeon, K. R.

2001-01-01

The spring load-deflection characteristic tests were performed for Westinghouse type 17x17 and 14x14 fuel assembly mid grids to evaluate the mechanical characteristics of the springs. Six kinds of prototype mid grids manufactured by KNFC were tested and two kinds of test methods were used: block test and in-grid test. The test results showed that all tested mid grid springs satisfied the criteria required at the beginning of fuel assembly life. In addition, the variation of spring characteristics resulting from the difference in the mechanical properties of spring material and spring shapes was investigated. And the validity of the test methods was discussed

Frequency-dependent springs in the seismic analysis of structures

International Nuclear Information System (INIS)

Tyapin, A.G.

2005-01-01

This paper presents a two-step algorithm for the seismic analysis of structure resting on the rigid embedded basement. Frequency-domain analysis of SSI is carried out on the second step for a platform model with special 'soil spring' which is complex, frequency-dependent, wave-dependent and non-balanced. Theory is presented to obtain the parameters of the soil spring on the first step of the analysis, performed without structure (only geometry of the basement is used) using well-known SASSI code (Lysmer et al, 1981) or in some other ways. On the second step in the SASSI analysis the soil spring is included in the model as a special finite element. Thus, the first step enables to save the computer resources on structure, the second step-to save resources on soil. Soil spring is the most general form for a SSI linear analysis: conventional springs and dashpots can be easily represented in such a format. Thus, the presented approach enables to study the impact of various factors (such as the embedment depth and soil-structure separation, the off-diagonal stiffness, various formulas for stiffness and damping, etc.) on the soil spring parameters. These parameters can be studied separately from the structure itself. As an example, the study of the horizontal soil mesh size is presented. Lumped soil spring may be used on the second step to obtain structural response spectra. To get stresses complex stiffness may be distributed over the basement slab and embedded walls. The proposed approach may be considered to be the alternative to the impedance method (see ASCE4-98). (authors)

Air and Space Power Journal-Spring 2016

Science.gov (United States)

2016-01-01

and military became interested in aviation for defensive purposes (e.g., concern over Japanese hostilities) and offers details about initial...Spring 2016 | 99 Book Reviews Empire. He finds that ace was invented in the late 1920s by cinema and that such a term would have been considered...In the real Pacific War, Japanese - Spring 2016 | 101 Book Reviews Americans were interned in camps, and a largely homogeneous American people fought

"I just wanted to get away": An analysis of spring breakers' travel motivations

Science.gov (United States)

Nuno F. Ribeiro; Paul E. Durrenberger; Careen M. Yarnal; Garry E. Chick

2010-01-01

Scholarly research on Spring Break has grown substantially and has often associated spring breakers' motivations with a number of risky behaviors. Recent research, however, has challenged these assumptions. The purpose of this study was to examine spring breakers' motivations for going on Spring Break. Unlike the media portrayal of Spring Break as a time of...

Nagra/Cedra: borings in the canton of Uri

International Nuclear Information System (INIS)

Schori, K.

1987-01-01

The first borehole at Oberbauenstock in Uri canton has been made. It is proposed that this will be the site for the future disposal of low and intermediate-level radioactive wastes in Switzerland. Other sites to be analysed are in the Grisons, Vaud and Nidwald cantons. (G.T.H.)

Thermoelastic properties on Cu-Zn-Al shape memory springs

Directory of Open Access Journals (Sweden)

Carlos Augusto do Nascimento Oliveira

2010-06-01

Full Text Available This paper present a thermomechanical study of actuators in form of helical springs made from shape memory alloy wires that can work as actuator and/or as sensor. These abilities are due to the martensitic transformation. This transformation is a diffusionless phase transition that occurs by a cooperative atomic rearrange mechanism. In this work, helical spring actuators were manufactured from Cu-Zn-Al shape memory alloy wires. The springs were submitted to constant tensile loads and thermal cycles. This procedure allows to determine thermoelastic properties of the shape memory springs. Thermomechanical properties were analyzed during 50 thermal cycles in the temperature range from 20 to 130 °C. Results of variations in critical transformation temperatures, thermoelastic strain and thermal hysteresis are discussed based on defects rearrangement and martensitic transformation theory.

Microbiology of Kamchatka Peninsula Hot Springs

Science.gov (United States)

Bonch-Osmolovsk, E.

2005-12-01

Hot springs of Uzon Caldera, Geyser Valley, Moutnovsky Volcano (Kamchatka Peninsula) served as the sources of isolation of numerous thermophilic prokaryotes, many of them representing new taxa. Among new isolates there were hyperthermophilic archaea - neutrophilic or acidophilic anaerobic organotrophs, able to use a wide range of polymeric organic substrates. Bacterial isolates were in majority represented by moderate thermophiles - organotrophs and lithoautotrophs. Latter group consisted of anaerobes oxidizing molecular hydrogen in the course of sulfate, sulfur or iron reduction, and of anaerobic CO-oxidizing, hydrogen-producing bacteria. Some of new isolates represented deep phylogenetic lineages in Bacteria domain. Microbial activity in Kamchatka hot springs was studied by means of radioisotopic tracing. The rates of methanogenesis, acetogenesis, inorganic carbon assimilation, acetate oxidation were determined in three different hot springs with pH ranging from 3.0 to 8.5 and water temeperature being in the range from 55 to 85oC. The results indicated the presence and activity of novel metabolic groups of thermophilic prokaryotes that so far have not been known in laboratory cultures.

Ephemeroptera, Plecoptera and Trichoptera in springs in Trentino (south-eastern Alps

Directory of Open Access Journals (Sweden)

Luana SILVERI

2011-09-01

Full Text Available Within the CRENODAT project (Biodiversity assessment and integrity evaluation of springs of Trentino - Italian Alps - and longterm ecological research, 2004-2008 we studied a total of 90 springs in Trentino (south-eastern Alps, Italy, 75 of which were used for statistical analysis. The springs were grouped into seven different types and represented all the available lithologies in the study area. Macrozoobenthos (Ephemeroptera, Plecoptera and Trichoptera; EPT was collected from stones, bryophytes and sediments. We investigated which physical, chemical or environmental features were important in determining EPT assemblage metrics at sites, by calculating the Shannon-Wiener diversity index, and applying a one-way ANOVA test, ANOSIM and SIMPER analyses. Statistical results highlighted the island character of the springs, each spring having its specific history and abiotic characteristics, which select for unique community patterns. For the faunistic analyses, we considered all springs where EPT taxa were recorded; a total of 88 taxa. Highest species richness was recorded among the Trichoptera, followed by the Plecoptera and Ephemeroptera, with 52, 30 and 6 taxa respectively. Fifteen Trichoptera and three Plecoptera species were recorded as new for the Autonomous Province of Trento. Our results confirm that, in the harsh environment of the Alps, the mild and stable ecological conditions that characterize spring-fed brooks contribute to maintaining and enhancing the regional biodiversity. Springs act as refuge areas for stream biota, providing more favourable conditions during spates or droughts (common in Alpine headwaters, or for particular stages of the insect life cycles. Springs also provide specific habitats for strictly crenobiontic species.

Analysis of the Residual Stresses in Helical Cylindrical Springs at High Temperature

Directory of Open Access Journals (Sweden)

H. Sun

2015-01-01

Full Text Available Creep is one of the basic properties of materials, its speed significantly depends on the temperature. Helical cylindrical springs are widely used in the elements of heating systems. This results in necessity of taking into account the effect of temperature on the stress-strain state of the spring. The object of research is a helical cylindrical spring used at high temperatures. Under this condition the spring state stability should be ensured.The paper studies relaxation of stress state and generation of residual stresses. Calculations are carried out in ABAQUS environment. The purpose of this work is to discuss the law of relaxation and residual stress in the spring.This paper describes the basic creep theories of helical cylindrical spring material. The calculation formulas of shear stress relaxation for a fixed compression ratio are obtained. Distribution and character of stress contour lines in the cross section of spring are presented. The stress relaxation – time relationships are discussed. The approximate formula for calculating relaxation shear stresses in the cross section of helical springs is obtained.The paper investigates creep ratio and law of residual stress variation in the cross-section of spring at 650℃. Computer simulation in ABAQUS environment was used. Research presents a finite element model of the spring creep in the cross-section.The paper conducts analysis of the stress changes for the creep under constant load. Under constant load stresses are quickly decreased in the around area of cross-section and are increased in the centre, i.e. the maximum and minimum stresses come close with time. Research work shows the possibility for using the approximate formula to calculate the relaxation shear stress in the cross section of spring and can provide a theoretical basis for predicting the service life of spring at high temperatures.In research relaxation processes of stress state are studied. Finite element model is cre

The Dynamic Characteristic and Hysteresis Effect of an Air Spring

Science.gov (United States)

Löcken, F.; Welsch, M.

2015-02-01

In many applications of vibration technology, especially in chassis, air springs present a common alternative to steel spring concepts. A design-independent and therefore universal approach is presented to describe the dynamic characteristic of such springs. Differential and constitutive equations based on energy balances of the enclosed volume and the mountings are given to describe the nonlinear and dynamic characteristics. Therefore all parameters can be estimated directly from physical and geometrical properties, without parameter fitting. The numerically solved equations fit very well to measurements of a passenger car air spring. In a second step a simplification of this model leads to a pure mechanical equation. While in principle the same parameters are used, just an empirical correction of the effective heat transfer coefficient is needed to handle some simplification on this topic. Finally, a linearization of this equation leads to an analogous mechanical model that can be assembled from two common spring- and one dashpot elements in a specific arrangement. This transfer into "mechanical language" enables a system description with a simple force-displacement law and a consideration of the nonobvious hysteresis and stiffness increase of an air spring from a mechanical point of view.

Computer aided FEA simulation of EN45A parabolic leaf spring

Directory of Open Access Journals (Sweden)

Krishan Kumar

2013-04-01

Full Text Available This paper describes computer aided finite element analysis of parabolic leaf spring. The present work is an improvement in design of EN45A parabolic leaf spring used by a light commercial automotive vehicle. Development of a leaf spring is a long process which requires lots of test to validate the design and manufacturing variables. A three-layer parabolic leaf spring of EN45A has been taken for this work. The thickness of leaves varies from center to the outer side following a parabolic pattern. These leaf springs are designed to become lighter, but also provide a much improved ride to the vehicle through a reduction on interleaf friction. The CAD modeling of parabolic leaf spring has been done in CATIA V5 and for analysis the model is imported in ANSYS-11 workbench. The finite element analysis (FEA of the leaf spring has been carried out by initially discretizing the model into finite number of elements and nodes and then applying the necessary boundary conditions. Maximum displacement, directional displacement, equivalent stress and weight of the assembly are the output targets of this analysis for comparison & validation of the work.

In search of spring mires in Namibia: the Waterberg area revisited

Directory of Open Access Journals (Sweden)

A.P. Grootjans

2015-07-01

Full Text Available The scarcity of peatlands and mires in Namibia is well known. Peatlands have been found in the north, which is the wettest part of the country. In the 1930s, spring mires were reported by German geologists in the Waterberg area, which also has relatively high annual precipitation. This short note reports some field observations and a literature search for old documents that mention the occurrence of springs and spring mires in the Waterberg region. The search was done by IMCG members who visited the Waterberg area in August 2014. We found springs, but no real mires. However, we found remnants of what might have been a large spring mire similar to that reported by the German geologist Paul Range, who found “local spring mires (Quellmoore with a peat thickness of several metres in northern South-West Africa”. Whether or not our peat remnants were situated at the same site as the Range discovery could not be assessed. We compared the landscape position of the peat remnants and spring in the Waterberg area of Namibia with information from an ongoing ecohydrological study in the Waterberg area of Limpopo Province, South Africa.

Reconstruction of false spring occurrences over the southeastern United States, 1901-2007: an increasing risk of spring freeze damage?

International Nuclear Information System (INIS)

Marino, Garrett P; Kaiser, Dale P; Gu, Lianhong; Ricciuto, Daniel M

2011-01-01

Near-record warmth over much of the United States during March 2007 promoted early growth of crops and vegetation. A widespread arctic air outbreak followed in early April, resulting in extensive agricultural losses over much of the south-central and southeastern US. This 'false spring' event also resulted in widespread damage to newly grown tissues of native deciduous forest species, shown by previous researchers to have had measurable effects on the terrestrial carbon cycle. The current study reconstructed the historical occurrence of false springs over most of the southeastern quarter of the conterminous US (32-39 deg. N; 75-98 deg. W) from 1901 to 2007 using daily maximum and minimum temperature records from 176 stations in the Global Historical Climatology Network database, and enhanced vegetation index (EVI) data derived from Moderate Resolution Imaging Spectroradiometer (MODIS) satellite observations. A false spring index was derived that examined the timing of the start of the growing season (SGS), or leaf emergence, relative to the timing of a potentially damaging last hard freeze (minimum temperature ≤ - 2.2 deg. C). SGS was modeled for the domain by combining EVI data with ground-based temperature 'degree day' calculations reflecting the rate of springtime warming. No significant area-wide, long-term SGS trend was found; however, over much of a contiguous region stretching from Mississippi eastward to the Carolinas, the timing of the last hard freeze was found to occur significantly later, this change occurring along with increased frequency of false springs. Earlier last hard freeze dates and decreased frequency of false springs were found over much of the northwestern part of the study region, including Arkansas and southern Missouri.

Development of transducers for integrated garter spring repositioning system

Energy Technology Data Exchange (ETDEWEB)

Sharma, B S.V.G.; Shyam, T V; Shrivastava, A K; Rupani, B B; Sinha, R K [Bhabha Atomic Research Centre, Bombay (India). Reactor Engineering Div.

1994-12-31

In order to reposition the dislocated garter springs in active channels of 235 MW Pressurised Heavy Water Reactors (PHWRs), a tool named as Integrated Garter Spring Repositioning System (INGRES) has been developed. The tool consists of transducers to detect the concentricity between the Pressure Tube (P/T) and Calandria Tube (C/T) and also to detect garter springs in the channel besides different modules for correcting the eccentricity between P/T and C/T and garter spring repositioning. The transducers used in the system namely Concentricity Detection Probe (CDP) and Garter Spring Detection Probe (GSDP) are based on the eddy current techniques. The CDP makes use of four eddy current bobbin probes separated 90 degrees apart in cross sectional plane of channel assembly. The transducer gives output signal in proportional to the air gap between P/T and C/T in two axes (X and Y) which are designed for the purpose. The output of the unit is obtained on the Cathode Ray Oscilloscope (CRO) screen in the form of illuminated dot. The dot position on the CRO screen gives the information about mismatch in concentricity between P/T and C/T of the channel. The GSDP meant for detecting garter springs in PHWR channel uses two sets of primary and secondary coils connected in differential mode. The output signals from the transducers are processed through a signal processing unit devised for the purpose to obtain output from it as a horizontal beam on the CRO screen. The garter spring presence in the channel is indicated by a change in the voltage level of beam and also by audio-visual indication in the form of buzzer and LED illumination on the processing unit. This paper gives general design and development aspects of the CDP and GSDP transducers of the INGRES tool. (author). 3 figs.

A Quadratic Spring Equation

Science.gov (United States)

Fay, Temple H.

2010-01-01

Through numerical investigations, we study examples of the forced quadratic spring equation [image omitted]. By performing trial-and-error numerical experiments, we demonstrate the existence of stability boundaries in the phase plane indicating initial conditions yielding bounded solutions, investigate the resonance boundary in the [omega]…

Goodenough Spring, Texas, USA: Discharge and water chemistry of a large spring deeply submerged under the binational Amistad Reservoir

Science.gov (United States)

Kamps, Ray H.; Tatum, Gregg S.; Gault, Mike; Groeger, Alan W.

2009-06-01

Goodenough Spring (Texas, USA) is a large spring near the border of the American state of Texas and the Mexican state of Coahuila, discharging into the international Amistad Reservoir on the river Rio Grande (Rio Bravo). Discharge was routinely measured from 1928 until 1968 to partition the flow of the river between the two countries in accordance with water-use treaties. Samples were analyzed for water-quality parameters in 1967-1968 prior to inundation under 45 m of Amistad Reservoir in 1968. Subsequently, discharge has been estimated indirectly by the International Boundary and Water Commission (IBWC). For the first direct measurements of the spring in 37 years, velocity and cross-sectional measurements were made and water samples collected in the summer of 2005 using advanced self-contained underwater breathing apparatus (SCUBA) techniques. Spring discharge was calculated at 2.03 m3 s-1, approximately one-half of the historical mean of 3.94 m3 s-1. In situ and laboratory analyses of samples for temperature, pH, dissolved oxygen, specific conductance, alkalinity, nitrate-nitrogen, dissolved solids, chloride, sulfate, fluoride, phosphorus, calcium, sodium, potassium, magnesium, and iron showed the water quality to be very good for human consumption and crop irrigation. Measurement values are relatively unchanged from those reported 37 years prior.

WSSRAP chemical plant geotechnical investigations for the Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1990-12-01

This document has been prepared for the United states Department of Energy (DOE) Weldon Spring Site Remedial Action Project (WSSRAP) by the Project Management Contractor (PMC), which consists of MK-Ferguson Company (MKF) and Morrison Knudsen Corporation Environmental Services Group (MKES) with Jacobs Engineering Group (JEG) as MKF's predesignated subcontractor. This report presents the results of site geotechnical investigations conducted by the PMC in the vicinity of the Weldon Spring chemical plant and raffinate pits (WSCP/RP) and in potential on-site and off-site clayey material borrow sources. The WSCP/RP is the proposed disposal cell (DC) site. 39 refs., 24 figs., 12 tabs

New spring wheat varieties ‘Panianka’ and ‘Diana’

Directory of Open Access Journals (Sweden)

О. А. Демидов

2016-12-01

Full Text Available Purpose. To create new competitive spring wheat varieties. Methods. Field study, laboratory test. Results. Based on the competitive variety trial, bread spring wheat line ‘Lutescens 07-26’ has been selected due to high values of such traits as resistance to fungal diseases, grain qua­lity(protein content accounted for 15.0%, 1000 kernel weight (44.6 g productivity (3.92 t/ha and lodging resistance (9 points. In 2011, it was submitted to the State variety testing as ‘Panianka’ variety. Durum spring wheat line ‘Leukurum 08-11’ was characterized by a number of positive traits: quite a high productivity (3.05 t/ha, short stem (79 cm, resistance to fungal diseases and lodging(9 points, and in 2011 it was submitted to the State variety testing as ‘Diana’ variety. According to the results of the State variety testing in 2012–2014, spring wheat varieties ‘Panianka’ and ‘Diana’ in 2015 were put on the State Register of plant varieties suitable for dissemination in Ukraine. Conclusions. For farms in Forest-Steppe and Polissia zones of Ukraine, bread and durum spring wheat varieties were bred by V. M.Remeslo Myronivka Institute of Wheat of NAAS of Ukraine that demonstrated rather high potential of productivity and adaptability to stress conditions. This goes to prove that cultivation of domestic spring wheat varieties will promote formation of high and quality grain yields.

Bending spring rate investigation of nanopipette for cell injection

Science.gov (United States)

Shen, Yajing; Zhang, Zhenhai; Fukuda, Toshio

2015-04-01

Bending of nanopipette tips during cell penetration is a major cause of cell injection failure. However, the flexural rigidity of nanopipettes is little known due to their irregular structure. In this paper, we report a quantitative method to estimate the flexural rigidity of a nanopipette by investigating its bending spring rate. First nanopipettes with a tip size of 300 nm are fabricated from various glass tubes by laser pulling followed by focused ion beam (FIB) milling. Then the bending spring rate of the nanopipettes is investigated inside a scanning electron microscope (SEM). Finally, a yeast cell penetration test is performed on these nanopipettes, which have different bending spring rates. The results show that nanopipettes with a higher bending spring rate have better cell penetration capability, which confirms that the bending spring rate may well reflect the flexural rigidity of a nanopipette. This method provides a quantitative parameter for characterizing the mechanical property of a nanopipette that can be potentially taken as a standard specification in the future. This general method can also be used to estimate other one-dimensional structures for cell injection, which will greatly benefit basic cell biology research and clinical applications.

Bending spring rate investigation of nanopipette for cell injection

International Nuclear Information System (INIS)

Shen, Yajing; Zhang, Zhenhai; Fukuda, Toshio

2015-01-01

Bending of nanopipette tips during cell penetration is a major cause of cell injection failure. However, the flexural rigidity of nanopipettes is little known due to their irregular structure. In this paper, we report a quantitative method to estimate the flexural rigidity of a nanopipette by investigating its bending spring rate. First nanopipettes with a tip size of 300 nm are fabricated from various glass tubes by laser pulling followed by focused ion beam (FIB) milling. Then the bending spring rate of the nanopipettes is investigated inside a scanning electron microscope (SEM). Finally, a yeast cell penetration test is performed on these nanopipettes, which have different bending spring rates. The results show that nanopipettes with a higher bending spring rate have better cell penetration capability, which confirms that the bending spring rate may well reflect the flexural rigidity of a nanopipette. This method provides a quantitative parameter for characterizing the mechanical property of a nanopipette that can be potentially taken as a standard specification in the future. This general method can also be used to estimate other one-dimensional structures for cell injection, which will greatly benefit basic cell biology research and clinical applications. (paper)

Investigation of membrane mechanics using spring networks: application to red-blood-cell modelling.

Science.gov (United States)

Chen, Mingzhu; Boyle, Fergal J

2014-10-01

In recent years a number of red-blood-cell (RBC) models have been proposed using spring networks to represent the RBC membrane. Some results predicted by these models agree well with experimental measurements. However, the suitability of these membrane models has been questioned. The RBC membrane, like a continuum membrane, is mechanically isotropic throughout its surface, but the mechanical properties of a spring network vary on the network surface and change with deformation. In this work spring-network mechanics are investigated in large deformation for the first time via an assessment of the effect of network parameters, i.e. network mesh, spring type and surface constraint. It is found that a spring network is conditionally equivalent to a continuum membrane. In addition, spring networks are employed for RBC modelling to replicate the optical tweezers test. It is found that a spring network is sufficient for modelling the RBC membrane but strain-hardening springs are required. Moreover, the deformation profile of a spring network is presented for the first time via the degree of shear. It is found that spring-network deformation approaches continuous as the mesh density increases. Copyright © 2014 Elsevier B.V. All rights reserved.

Weldon Spring dose calculations

International Nuclear Information System (INIS)

Dickson, H.W.; Hill, G.S.; Perdue, P.T.

1978-09-01

In response to a request by the Oak Ridge Operations (ORO) Office of the Department of Energy (DOE) for assistance to the Department of the Army (DA) on the decommissioning of the Weldon Spring Chemical Plant, the Health and Safety Research Division of the Oak Ridge National Laboratory (ORNL) performed limited dose assessment calculations for that site. Based upon radiological measurements from a number of soil samples analyzed by ORNL and from previously acquired radiological data for the Weldon Spring site, source terms were derived to calculate radiation doses for three specific site scenarios. These three hypothetical scenarios are: a wildlife refuge for hunting, fishing, and general outdoor recreation; a school with 40 hr per week occupancy by students and a custodian; and a truck farm producing fruits, vegetables, meat, and dairy products which may be consumed on site. Radiation doses are reported for each of these scenarios both for measured uranium daughter equilibrium ratios and for assumed secular equilibrium. Doses are lower for the nonequilibrium case

EVALUATION OF PRECIPITATION HARDENING HEAT TREATMENT OF PH 17-7 STAINLESS STEEL SPRING

Directory of Open Access Journals (Sweden)

A. A. Babakoohi Ashrafi

2016-06-01

Full Text Available In this paper, the influence of heat treatment on PH17-7 stainless steel spring was evaluated. Precipitation hardening phenomenon of  PH 17-7 steel was evaluated in three stages. First, the spring constant changes with time and temperature was evaluated. Second, the spring constant changes with respect to its original length at constant temperature and time with blocking (spring length after compression, 18 and 21 mm were investigated.  And finally, the spring heat treatment at 480 °C for 80 min and then holding at 230 °C in oil bath for 60 min without blocking were investigated. The results showed that the use of 18 mm block have large spring constant than 21 mm block. The optimal conditions (480°C for 80 min for this spring to reaching maximum spring constant were determined.

What can be done with SPring-8. Features of the facility

International Nuclear Information System (INIS)

Hara, Masahiro

2006-01-01

SPring-8 is the world's largest third-generation synchrotron radiation facility. The definition, features, facility (SPring-8), applications and examples of researches with SR (synchrotron radiation) are explained. SR is characterized by brightness, high directionality and variable polarization. History of facilities of SR is stated. Outline of SPring-8, resources of SR, the specifications, beam line map, brightness of SPring-8 are shown. The examples of researches with SPring-8 contained the refraction-contrast imaging, soft X-ray microscope, XAFS, X-ray topography, photoelectron emission microscopy, atomic structure analysis of protein, MAD method, X-ray fluorescence spectroscopy, lithography and thin film analysis. Operation conditions of the SPring-8 storage ring, interaction between X-ray and materials, the principle of refraction-contrast, measurement of XAFS, Bragg's conditions of X-ray scattering, BL02B2 (beam-line of powder diffraction), BL04B1 and SPEED1500, concept of protein analysis beam-line and MAD method, and spectra of trace analysis of arsenious acid are illustrated. (S.Y.)

A simulation methodology of spacer grid residual spring deflection for predictive and interpretative purposes

International Nuclear Information System (INIS)

Kim, K. T.; Kim, H. K.; Yoon, K. H.

1994-01-01

The in-reactor fuel rod support conditions against the fretting wear-induced damage can be evaluated by spacer grid residual spring deflection. In order to predict the spacer grid residual spring deflection as a function of burnup for various spring designs, a simulation methodology of spacer grid residual spring deflection has been developed and implemented in the GRIDFORCE program. The simulation methodology takes into account cladding creep rate, initial spring deflection, initial spring force, and spring force relaxation rate as the key parameters affecting the residual spring deflection. The simulation methodology developed in this study can be utilized as an effective tool in evaluating the capability of a newly designed spacer grid spring to prevent the fretting wear-induced damage

Balneological Evaluation of the Tafadek Spring, Agadez Region, Niger Republic

Science.gov (United States)

Nghargbu, K.; Latour, T.; Ponikowska, I.; Kurowska, E.

2012-04-01

West Africa, particularly Niger Republic is home to thousands of tourists annually. The vast Saharan desert and it's numerous oases in the northern parts of the Republic are a hot attraction on their own. However, in a recent survey of medicinal springs within the West African sub-region, the only hot spring in this country known locally for its therapeutic egress was analyzed. Located about 160km West of Agadez, the "Tafadek" spring with a yield of over 5l/s and temperature of about 50oC, rich in fluoride and silica is a specific water with capacity for application in balneotherapy for the treatment of orthopaedic, rheumatological, neurological, urinary tract infections, and osteoporosis. If the Tafadek spring is developed into a modern health resort promoting balneotherapy, health (balnear) tourism which is non-existent in Niger Republic today could kick start a new dawn in the health/economic development of the nation and the sub-region at large. Keywords: West Africa, Nigeria, Balneotherapy, Health tourism, Spring

Base excitation testing system using spring elements to pivotally mount wind turbine blades

Science.gov (United States)

Cotrell, Jason; Hughes, Scott; Butterfield, Sandy; Lambert, Scott

2013-12-10

A system (1100) for fatigue testing wind turbine blades (1102) through forced or resonant excitation of the base (1104) of a blade (1102). The system (1100) includes a test stand (1112) and a restoring spring assembly (1120) mounted on the test stand (1112). The restoring spring assembly (1120) includes a primary spring element (1124) that extends outward from the test stand (1112) to a blade mounting plate (1130) configured to receive a base (1104) of blade (1102). During fatigue testing, a supported base (1104) of a blad (1102) may be pivotally mounted to the test stand (1112) via the restoring spring assembly (1120). The system (1100) may include an excitation input assembly (1140) that is interconnected with the blade mouting plate (1130) to selectively apply flapwise, edgewise, and/or pitch excitation forces. The restoring spring assemply (1120) may include at least one tuning spring member (1127) positioned adjacent to the primary spring element (1124) used to tune the spring constant or stiffness of the primary spring element (1124) in one of the excitation directions.

Morphological and genetic perspectives of peach fruit responses to spring frost

Science.gov (United States)

Spring frost is one of the most unpredictable cropping factors in many peach production areas. A severe spring frost can wipe out an entire peach crop whereas a mild spring frost may naturally help thinning as is common practice in commercial peach production. The extent of frost damage depends on t...

Identifying anomalously early spring onsets in the CESM large ensemble project

Science.gov (United States)

Labe, Zachary; Ault, Toby; Zurita-Milla, Raul

2017-06-01

Seasonal transitions from winter to spring impact a wide variety of ecological and physical systems. While the effects of early springs across North America are widely documented, changes in their frequency and likelihood under the combined influences of climate change and natural variability are poorly understood. Extremely early springs, such as March 2012, can lead to severe economical losses and agricultural damage when these are followed by hard freeze events. Here we use the new Community Earth System Model Large Ensemble project and Extended Spring Indices to simulate historical and future spring onsets across the United States and in the particular the Great Lakes region. We found a marked increase in the frequency of March 2012-like springs by midcentury in addition to an overall trend towards earlier spring onsets, which nearly doubles that of observational records. However, changes in the date of last freeze do not occur at the same rate, therefore, causing a potential increase in the threat of plant tissue damage. Although large-scale climate modes, such as the Pacific Decadal Oscillation, have previously dominated decadal to multidecadal spring onset trends, our results indicate a decreased role in natural climate variability and hence a greater forced response by the end of the century for modulating trends. Without a major reduction in greenhouse gas emissions, our study suggests that years like 2012 in the US could become normal by mid-century.

ANALYSIS OF HOLLOW COIL HELICAL EXTENSION SPRING AND THE STUDY OF OPTIMIZING THE WEIGHT

OpenAIRE

Naman Gupta*1, Manas purohit2 & Deepika potghan3

2017-01-01

This paper shows the study which deals with the weight reduction for tensile extension spring by changing the solid spring to hollow one. The springs which are generally used are in solid form due to which the weight of entire body in which the spring is attached gets increased. The forces which can be act on spring may be linear push or linear pull or radial type. This spring deflect by pulling and regain its shape when pulling is neglect. The weight of tensile spring is reduced by changing ...

The false spring of 2012, earliest in North American record

Science.gov (United States)

Ault, T.R.; Henebry, G.M.; de Beurs, K. M.; Schwartz, M.D.; Betancourt, Julio L.; Moore, David

2013-01-01

Phenology - the study of recurring plant and animal life cycle stages, especially their timing and relationships with weather and climate - is becoming an essential tool for documenting, communicating, and anticipating the consequences of climate variability and change. For example, March 2012 broke numerous records for warm temperatures and early flowering in the United States [Karl et al., 2012; Elwood et al., 2013]. Many regions experienced a “false spring,” a period of weather in late winter or early spring sufficiently mild and long to bring vegetation out of dormancy prematurely, rendering it vulnerable to late frost and drought.As global climate warms, increasingly warmer springs may combine with the random climatological occurrence of advective freezes, which result from cold air moving from one region to another, to dramatically increase the future risk of false springs, with profound ecological and economic consequences [e.g., Gu et al., 2008; Marino et al., 2011; Augspurger, 2013]. For example, in the false spring of 2012, an event embedded in long-term trends toward earlier spring [e.g., Schwartz et al., 2006], the frost damage to fruit trees totaled half a billion dollars in Michigan alone, prompting the federal government to declare the state a disaster area [Knudson, 2012].

How reflected wave fronts dynamically establish Hooke's law in a spring

International Nuclear Information System (INIS)

Fahy, Stephen; O'Riordan, John; O'Sullivan, Colm; Twomey, Patrick

2012-01-01

A simple benchtop experiment in which a moving cart collides with a fixed spring is described. Force-time and force-distance data recorded during the collision display the transit of compression wave fronts through the spring following impact. These data can be used by students to develop a computational model of the dynamics of this simple mass-spring-sensor system using a simple application of the wave equation and thereby develop an intriguing picture of how a spring realizes Hooke's law approximately in this dynamic physical problem. (paper)

State-space prediction of spring discharge in a karst catchment in southwest China

Science.gov (United States)

Li, Zhenwei; Xu, Xianli; Liu, Meixian; Li, Xuezhang; Zhang, Rongfei; Wang, Kelin; Xu, Chaohao

2017-06-01

Southwest China represents one of the largest continuous karst regions in the world. It is estimated that around 1.7 million people are heavily dependent on water derived from karst springs in southwest China. However, there is a limited amount of water supply in this region. Moreover, there is not enough information on temporal patterns of spring discharge in the area. In this context, it is essential to accurately predict spring discharge, as well as understand karst hydrological processes in a thorough manner, so that water shortages in this area could be predicted and managed efficiently. The objectives of this study were to determine the primary factors that govern spring discharge patterns and to develop a state-space model to predict spring discharge. Spring discharge, precipitation (PT), relative humidity (RD), water temperature (WD), and electrical conductivity (EC) were the variables analyzed in the present work, and they were monitored at two different locations (referred to as karst springs A and B, respectively, in this paper) in a karst catchment area in southwest China from May to November 2015. Results showed that a state-space model using any combinations of variables outperformed a classical linear regression, a back-propagation artificial neural network model, and a least square support vector machine in modeling spring discharge time series for karst spring A. The best state-space model was obtained by using PT and RD, which accounted for 99.9% of the total variation in spring discharge. This model was then applied to an independent data set obtained from karst spring B, and it provided accurate spring discharge estimates. Therefore, state-space modeling was a useful tool for predicting spring discharge in karst regions in southwest China, and this modeling procedure may help researchers to obtain accurate results in other karst regions.

Work plan for the remedial investigation/feasibility study-environmental impact statement for the Weldon Spring site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Peterson, J.M.; MacDonell, M.M.; Haroun, L.A.; Nowadly, F.K.; Knight, W.C.; Vajda, G.F.

1988-08-01

The Weldon Spring Site Remedial Action Project is being conducted as a Major System Acquisition under the Surplus Facilities Management Program (SFMP) of the US Department of Energy (DOE). The major goals of the SFMP are to eliminate potential hazards to the public and the environment that are associated with contamination at SFMP sites and to make surplus real property available for other uses to the extent possible. The Weldon Spring site is located near Weldon Spring, Missouri, about 48 km (30 mi) west of St. Louis. It is surrounded by large tracts of land owned by the federal government and the state of Missouri. The site consists of four raffinate pits, an inactive chemical plant, and a contaminated quarry. The raffinate pits and chemical plant are on adjoining land about 3.2 km (2 mi) southwest of the junction of Missouri (State) Route 94 and US Route 40/61, with access from Route 94. The quarry is located in a comparatively remote area about 6.4 km (4 mi) south-southwest of the raffinate pits and chemical plant area; the quarry can also be accessed from Route 94. These areas are fenced and closed to the public. From 1941 to 1944, the US Department of the Army operated the Weldon Spring Ordnance Works, constructed on the land that is now the Weldon Spring site, for production of trinitrotoluene (TNT) and dinitrotoluene (DNT). The Army used the quarry for disposal of rubble contaminated with TNT. In the mid 1950s, 83 ha (205 acres) of the ordnance works property was transferred to the US Atomic Energy Commission (AEC); this is now the raffinate pits and chemical plant area. An additional 6 ha (15 acres) was later transferred to the AEC for expansion of waste storage capacity. 23 refs., 37 figs., 21 tabs

Integrated Field Analyses of Thermal Springs

Science.gov (United States)

Shervais, K.; Young, B.; Ponce-Zepeda, M. M.; Rosove, S.

2011-12-01

A group of undergraduate researchers through the SURE internship offered by the Southern California Earthquake Center (SCEC) have examined thermal springs in southern Idaho, northern Utah as well as mud volcanoes in the Salton Sea, California. We used an integrated approach to estimate the setting and maximum temperature, including water chemistry, Ipad-based image and data-base management, microbiology, and gas analyses with a modified Giggenbach sampler.All springs were characterized using GISRoam (tmCogent3D). We are performing geothermometry calculations as well as comparisons with temperature gradient data on the results while also analyzing biological samples. Analyses include water temperature, pH, electrical conductivity, and TDS measured in the field. Each sample is sealed and chilled and delivered to a water lab within 12 hours.Temperatures are continuously monitored with the use of Solinst Levelogger Juniors. Through partnership with a local community college geology club, we receive results on a monthly basis and are able to process initial data earlier in order to evaluate data over a longer time span. The springs and mudpots contained microbial organisms which were analyzed using methods of single colony isolation, polymerase chain reaction, and DNA sequencing showing the impact of the organisms on the springs or vice versa. Soon we we will collect gas samples at sites that show signs of gas. This will be taken using a hybrid of the Giggenbach method and our own methods. Drawing gas samples has proven a challenge, however we devised a method to draw out gas samples utilizing the Giggenbach flask, transferring samples to glass blood sample tubes, replacing NaOH in the Giggenbach flask, and evacuating it in the field for multiple samples using a vacuum pump. We also use a floating platform devised to carry and lower a levelogger, to using an in-line fuel filter from a tractor in order to keep mud from contaminating the equipment.The use of raster

Rational design of the exchange-spring permanent magnet.

Science.gov (United States)

Jiang, J S; Bader, S D

2014-02-12

The development of the optimal exchange-spring permanent magnet balances exchange hardening, magnetization enhancement, and the feasibility of scalable fabrication. These requirements can be met with a rational design of the microstructural characteristics. The magnetization processes in several model exchange-spring structures with different geometries have been analyzed with both micromagnetic simulations and nucleation theory. The multilayer geometry and the soft-cylinders-in-hard-matrix geometry have the highest achievable figure of merit (BH)max, while the soft-spheres-in-hard-matrix geometry has the lowest upper limit for (BH)max. The cylindrical geometry permits the soft phase to be larger and does not require strict size control. Exchange-spring permanent magnets based on the cylindrical geometry may be amenable to scaled-up fabrication.

Rational design of the exchange-spring permanent magnet

International Nuclear Information System (INIS)

Jiang, J S; Bader, S D

2014-01-01

The development of the optimal exchange-spring permanent magnet balances exchange hardening, magnetization enhancement, and the feasibility of scalable fabrication. These requirements can be met with a rational design of the microstructural characteristics. The magnetization processes in several model exchange-spring structures with different geometries have been analyzed with both micromagnetic simulations and nucleation theory. The multilayer geometry and the soft-cylinders-in-hard-matrix geometry have the highest achievable figure of merit (BH) max , while the soft-spheres-in-hard-matrix geometry has the lowest upper limit for (BH) max . The cylindrical geometry permits the soft phase to be larger and does not require strict size control. Exchange-spring permanent magnets based on the cylindrical geometry may be amenable to scaled-up fabrication. (paper)

Use of SPring-8 in drug development

International Nuclear Information System (INIS)

Nishijima, Kazumi

2006-01-01

Protein structure analysis consortium was established by 21 drug companies and has analyzed protein structures using the beam line BL32B2 of SPring-8 since September in 2002. Outline of the protein structure analysis consortium, contribution of SPring-8 to drug development, and the present status and future of use of SPring-8 are stated. For examples of structure analysis, the human nuclear enzyme (PARP-1) fragment complex crystal structure, human ISG20, human dipeptidine peptidase IV, human cMDH, chromatin binding human nuclear enzyme complex, change of structure of each step of tyrosine activation of bacteria tyrosine tRNA synthetase are described. Contribution of analysis of protein structure and functions to drug development, development process of new drug, drug screening using compounds database on the basis of the three dimensional structure of receptor active site, genome drug development, and the effects of a target drug on the market are explained. (S.Y.)

Feasibility study for management of the bulk wastes at the Weldon Spring quarry, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1990-02-01

The US Department of Energy (DOE), under its Surplus Facilities Management Program, is responsible for conducting remedial actions at the Weldon Spring site in St. Charles County, Missouri. The Weldon Spring site, which is listed on the National Priorities List of the US Environmental Protection Agency (EPA), became contaminated as a result of processing and disposal activities that took place from the 1940s through the 1960s. The site consists of a quarry and a chemical plant area located about 6.4 km (4 mi) northeast of the quarry. The quarry is surrounded by the Weldon Spring Wildlife Area and is near a well field that constitutes a major source of potable water for St. Charles County; the nearest supply well is located about 0.8 km (0.5 mi) southeast of the quarry. From 1942 to 1969, the quarry was used for the disposal of various radioactively and chemically contaminated materials. Bulk wastes in the quarry consist of contaminated soils and sediments, rubble, metal debris, and equipment. As part of overall site remediation, DOE is proposing to conduct an interim remedial action at the quarry to manage the radioactively and chemically contaminated bulk waste contained therein. 105 refs., 33 figs., 42 tabs

Archaeal and bacterial community analysis of several Yellowstone National Park hot springs

Science.gov (United States)

Colman, D. R.; Takacs-Vesbach, C. D.

2012-12-01

The hot springs of Yellowstone National Park (YNP) are home to a diverse assemblage of microorganisms. Culture-independent studies have significantly expanded our understanding of the diversity of both Bacteria and Archaea present in YNP springs as well as the geochemical and ecological controls on communities. While the ecological analysis of Bacteria among the physicochemically heterogenous springs of YNP has been previously conducted, less is known about the extent of diversity of Archaeal communities and the chemical and ecological controls on their populations. Here we report a culture-independent analysis of 31 hot spring archaeal and bacterial communities of YNP springs using next generation sequencing. We found the phylogenetic diversity of Archaea to be generally comparable to that of co-occurring bacterial communities although overall, in the springs we investigated, diversity was higher for Bacteria than Archaea. Chemical and physical controls were similar for both domains with pH correlating most strongly with community composition. Community differences reflected the partitioning of taxonomic groups in low or high pH springs for both domains. Results will be discussed in a geochemical and ecological context.

Comment on Origin of Groundwater Discharge at Fall River Springs

Energy Technology Data Exchange (ETDEWEB)

Rose, T

2006-10-20

I'm writing at the request of the Pit River Tribe to offer my professional opinion as a geochemist regarding the origin of groundwater discharge at the Fall River Springs, Shasta Co., California. In 1997, I conducted a study of the large volume cold springs associated with the Cascade Volcanoes in northern California, in collaboration with one of my colleagues. This work was published as a Lawrence Livermore National Laboratory report (Davisson and Rose, 1997). The Fall River Springs emerge from the distal end of the Giant Crater Lava Field, a laterally extensive basalt flow that stretches from the southern flank of Medicine Lake Volcano southward for a distance of 40 km. Both Medicine Lake Volcano and the Giant Crater Lava Field have virtually no surface water drainages. Precipitation that falls in these areas is inferred to seep into fractures in the rock, where it is carried down gradient under the force of gravity. Mean annual precipitation rates on Medicine Lake Volcano and the Giant Crater Lava field are adequate to account for the {approx}1200 ft{sup 3}/sec discharge of the Fall River Springs. To evaluate the origin of the springs using geochemical methods, water samples were collected from the Fall River Springs and the Medicine Lake highlands and analyzed for oxygen and hydrogen isotope ratios. The isotope ratios measured for a groundwater sample are diagnostic of the average composition of the precipitation from which the water was derived. The isotope ratios of rain and snow also vary systematically with elevation, such that groundwater derived from recharge at higher elevations can be distinguished from that which originated at lower elevations. The stable isotope data for the Fall River Springs are consistent with groundwater recharge on the Medicine Lake Volcano and adjacent lava field. Mass balance calculations suggest that approximately half of the Fall River Springs flow is derived from the volcanic edifice. Rose and Davisson (1996) showed

Deformation behavior of cell spring of an irradiated spacer grid

International Nuclear Information System (INIS)

Jin, Y. G.; Baek, S. J.; Ryu, W. S.; Kim, G. S.; Yoo, B. O.; Kim, D. S.; Ahn, S. B.; Chun, Y. B.; Choo, Y. S.

2012-01-01

Mechanical properties of a space grid of a fuel assembly are of great importance for fuel operation reliability in extended fuel burnup and duration of fuel life. The spacer grid with inner and outer straps has cell spring and dimples, which are in contact with the fuel rod. The spacer grids supporting the fuel rods absorb vibration impacts due to the reactor coolant flow and also grid spring force is decreasing under irradiation. This reduction of contact force might cause the grid to rod fretting wear. The fretting failure of the fuel rod is one of the significant issues recently in the nuclear industry from an economical as well as a safety concern. Thus, it is important to understand the characteristics of cell spring behavior for an irradiated spacer grid. In the present study, the stiffness test and dimensional measurement of cell springs were conducted to investigate the deformation behavior of cell springs of an irradiated spacer grid in a hot cell at IMEF (irradiated materials examination facility) of KAERI

Spatial Characteristics of Geothermal Spring Temperatures and Discharge Rates in the Tatun Volcanic Area, Taiwan

Science.gov (United States)

Jang, C. S.; Liu, C. W.

2014-12-01

The Tatun volcanic area is the only potential volcanic geothermal region in the Taiwan island, and abundant in hot spring resources owing to stream water mixing with fumarolic gases. According to the Meinzer's classification, spring temperatures and discharge rates are the most important properties for characterizing spring classifications. This study attempted to spatially characterize spring temperatures and discharge rates in the Tatun volcanic area, Taiwanusing indicator kriging (IK). First, data on spring temperatures and discharge rates, which were collected from surveyed data of the Taipei City Government, were divided into high, moderate and low categories according to spring classification criteria, and the various categories were regarded as estimation thresholds. Then, IK was adopted to model occurrence probabilities of specified temperatures and discharge rates in springs, and to determine their classifications based on estimated probabilities. Finally, nine combinations were obtained from the classifications of temperatures and discharge rates in springs. Moreover, the combinations and features of spring water were spatially quantified according to seven sub-zones of spring utilization. A suitable and sustainable development strategy of the spring area was proposed in each sub-zone based on probability-based combinations and features of spring water.The research results reveal that the probability-based classifications using IK provide an excellent insight in exploring the uncertainty of spatial features in springs, and can provide Taiwanese government administrators with detailed information on sustainable spring utilization and conservation in the overexploited spring tourism areas. The sub-zones BT (Beitou), RXY (Rd. Xingyi), ZSL (Zhongshanlou) and LSK (Lengshuikeng) with high or moderate discharge rates are suitable to supply spring water for tourism hotels.Local natural hot springs should be planned in the sub-zones DBT (Dingbeitou), ZSL, XYK

DEPENDENCE OF AIR SPRING PARAMETERS ON THROTTLE RESISTANCE

Directory of Open Access Journals (Sweden)

O. H. Reidemeister

2016-04-01

Full Text Available Purpose. In this paper it is necessary to conduct: 1 research and analyse the influence of throttle element pneumatic resistance on elastic and damping parameters of air spring; 2 to obtain the dependence of air spring parameters on throttle element pneumatic resistance value. Methodology. The work presents the elaborated model of the air spring as a dynamic system with three phase coordinates (cylinder pressure, auxiliary reservoir pressure, cylinder air mass. Stiffness and viscosity coefficients were determined on the basis of system response to harmonic kinematic disturbance. The data for the analysis are obtained by changing the capacity of the connecting element and the law of pressure variation between the reservoir and the cylinder. The viscosity coefficient is regarded as the viscosity ratio of the hydraulic damper, which for one oscillation cycle consumes the same energy as the air spring. The process of air condition change inside the cylinder (reservoir is considered to be adiabatic; the mass air flow through the connecting element depends on the pressure difference. Findings. We obtained the curves for spring viscosity and stiffness coefficients dependence on the throttle resistance at three different laws, linking airflow through the cylinder with the pressure difference in cylinder and reservoir. At both maximum and minimum limiting resistance values the spring viscosity tends to zero, reaching its peak in the mean resistance values. Stiffness increases monotonically with increasing resistance, tends to the limit corresponding to the absence of an auxiliary reservoir (at high resistance and the increase in cylinder volume by the reservoir volume (at low resistance. Originality.The designed scheme allows determining the optimal parameters of elastic and damping properties of the pneumatic system as function of the throttle element air resistance. Practical value.The ability to predict the parameters of elastic and damping properties

Habitat features and distribution of Salamandra salamandra in underground springs

Directory of Open Access Journals (Sweden)

Raoul Manenti

2009-12-01

Full Text Available Subterranean habitats are among the less known terrestrial habitats, but can reveal an unexpected biodiversity, and can play an underestimated role for amphibians. The fire salamander Salamandra salamandra is sometimes found in underground environments, but the factors affecting its distribution in subterranean spaces remain substantially unexplored. We repeatedly surveyed some hypogeous springs, such as draining galleries and “bottini” in NW Italy, in order to evaluate the relationship between environmental features and distribution of S. salamandra in these underground springs. We performed visual encounter surveys to assess the occurrence of larvae, juveniles or adults in springs. We also recorded four habitat variables: easy of access, isolation, macrobenthos richness and forest cover of the surrounding landscape. We used generalized linear models to evaluate the relationships between habitat features and occurrence of larvae. We observed larvae of S. salamandra in 13 out of 22 springs; their presence was associated to springs with high easy of access and with relatively rich macrobenthos communities. In underground springs, larval development apparently required longer time than in nearby epigeous streams. Nevertheless, S. salamandra can attain metamorphosis in this environment. The occurrence of S. salamandra in underground environments was not accidental, but repeated in the time and interesting from an ecological point of view, confirming the high plasticity of the species.

Engineering evaluation/cost analysis for the proposed removal action at the Southeast Drainage near the Weldon Spring Site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1996-08-01

The engineering evaluation/cost analysis (EE/CA) has been prepared to support the proposed removal of contaminated sediment from selected portions of the Southeast Drainage as part of cleanup activities being conducted at the Weldon Spring site in St. Charles County, Missouri, by the U.S. Department of Energy (DOE). The cleanup activities are conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended, incorporating the values of the National Environmental Policy Act (NEPA). The Weldon Spring site is located near the town of Weldon Spring, about 48 km (30 mi) west of St. Louis. It consists of two noncontiguous areas: the chemical plant area and a limestone quarry about 6.4 km (4 mi) south-southwest of the chemical plant area. The Southeast Drainage is a natural 2.4-km (1.5-mi) channel that carries surface runoff to the Missouri River from the southern portion of the chemical plant area and a small portion of the ordnance works area (part of the Weldon Spring Training Area) south of the groundwater divide. The drainage became contaminated as a result of past activities of the U.S. Army and the DOE (and its predecessors)

Differentiated spring behavior under changing hydrological conditions in an alpine karst aquifer

Science.gov (United States)

Filippini, Maria; Squarzoni, Gabriela; De Waele, Jo; Fiorucci, Adriano; Vigna, Bartolomeo; Grillo, Barbara; Riva, Alberto; Rossetti, Stefano; Zini, Luca; Casagrande, Giacomo; Stumpp, Christine; Gargini, Alessandro

2018-01-01

Limestone massifs with a high density of dolines form important karst aquifers in most of the Alps, often with groundwater circulating through deep karst conduits and water coming out of closely spaced springs with flow rates of over some cubic meters per second. Although several hydrogeological studies and tracing experiments were carried out in many of these carbonate mountains in the past, the hydrogeology of most of these karst aquifers is still poorly known. Geological, hydrodynamic and hydrochemical investigations have been carried out in one of the most representative of these areas (Cansiglio-Monte Cavallo, NE Italy) since spring 2015, in order to enhance the knowledge on this important type of aquifer system. Additionally, a cave-to-spring multitracer test was carried out in late spring 2016 by using three different fluorescent tracers. This hydrogeological study allowed: 1) gathering new detailed information on the geological and tectonic structure of such alpine karst plateau; 2) defining discharge rates of the three main springs (Gorgazzo, Santissima, and Molinetto) by constructing rating curves; 3) understanding the discharging behavior of the system with respect to different recharge conditions; 4) better defining the recharge areas of the three springs. The three nearby springs (the spring front stretches over 5 km), that drain the investigated karst aquifer system, show different behaviors with respect to changing discharge conditions, demonstrating this aquifer to be divided in partially independent drainage systems under low-flow conditions, when their chemistry is clearly differentiated. Under high-flow conditions, waters discharging at all springs show more similar geochemical characteristics. The combination of geochemistry, hydrodynamic monitoring and dye tracing tests has shown that the three springs have different recharge areas. The study points out that even closely spaced karst springs, that apparently drain the same karst mountain, can

Silicon isotope study of thermal springs in Jiaodong Region,Shandong Province

Institute of Scientific and Technical Information of China (English)

徐跃通; 李红梅; 冯海霞; 周晨; 吴元芳; 张邦花

2001-01-01

Based on δ30Si and δ32Si isotope geochemistry, the origin and evolutionary mechanism of thermal springs in Jiaodong region are studied. The mean value of δ30Si of dissolved silica of thermal spring water in Jiaodong is 0.1‰. Thermal spring water ages using δ32Si dating method range from 387a to 965a.

Investigation about Role of Algae in Kazeroon Sasan Spring Odor

Directory of Open Access Journals (Sweden)

A Hamzeian

2016-05-01

Full Text Available Introduction: As odor for potable water is unpleasant for costumers, it needs to do researches for finding the reasons of odorous water. Sasan spring that is located in, near kazeroon city, Fars, Iran, is potable water resource for Kazeroon and Booshehr city and many other villages. Water in Sasan spring has the odor problem. With regards to important   role of algae on ado r problems in this study the role of algae on   odor was investigated. Methods: After regular sampling, the TON (threshold odor number was indicated and algae species was distinguished and the number of total algae and any species  of algae was numbers by microscopic direct numbering method .as the algae mass  is related to nitrogen and phosphor concentration, results of concentration Of nitrogen and phosphor in this spring that was examined regularity by water company was investigated and compared to concentration of these component that are need for algae growing.   Results: results shows that TON was in range  of 4.477 to 6.2 that indicated  oderous limit . Regression and diagram between TON and number of total algae showed the linear relationship. The concentration of nitrogen and phosphor, showed adequate condition for algal grow. Result of determination of algae species showed high population of Oscilatoria and Microcystis species, which are known as essential case of mold odor in water resources. Investigation on geological maps in the region around the Sasan spring, show alluvium source and is effected by surface part of it’s around land. Conclusion: because of the algae was determined as the essential cause of odor   in the spring, and algal growth is related to nutrients, and because of the surface pollution can penetrate in the alluvium lands around the spring, and effect the water in spring, so nutrient control and management is the essential way for odor control in the spring.

Uranium in spring water and bryophytes at Basin Creek in central Idaho

International Nuclear Information System (INIS)

Shacklette, H.T.; Erdman, J.A.

1982-01-01

Arkosic sandstones and conglomerates of Tertiary age beneath the Challis Volcanics of Eocene age at Basin Creek, 10 km northeast of Stanley, Idaho, contain uranium-bearing vitrainized carbon fragments. The economic potential of these sandstones and conglomerates is currently being assessed. Water from 22 springs and associated bryophytes were sampled; two springs were found to contain apparently anomalous concentrations (normalized) of uranium. Water from a third spring contained slightly anomalous amounts of uranium, and two species of mosses at the spring contained anomalous uranium and high levels of both cadmium and lead. Water from a fourth spring was normal for uranium, but the moss from the water contained a moderate uranium level and highly anomalous concentrations of lead, germanium, and thallium. These results suggest that, in the Basin Creek area, moss sampling at springs may give a more reliable indication of uranium occurrence than would water sampling. (Auth.)

Effect of distributive mass of spring on power flow in engineering test

Science.gov (United States)

Sheng, Meiping; Wang, Ting; Wang, Minqing; Wang, Xiao; Zhao, Xuan

2018-06-01

Mass of spring is always neglected in theoretical and simulative analysis, while it may be a significance in practical engineering. This paper is concerned with the distributive mass of a steel spring which is used as an isolator to simulate isolation performance of a water pipe in a heating system. Theoretical derivation of distributive mass effect of steel spring on vibration is presented, and multiple eigenfrequencies are obtained, which manifest that distributive mass results in extra modes and complex impedance properties. Furthermore, numerical simulation visually shows several anti-resonances of the steel spring corresponding to impedance and power flow curves. When anti-resonances emerge, the spring collects large energy which may cause damage and unexpected consequences in practical engineering and needs to be avoided. Finally, experimental tests are conducted and results show consistency with that of the simulation of the spring with distributive mass.

Based on Artificial Neural Network to Realize K-Parameter Analysis of Vehicle Air Spring System

Science.gov (United States)

Hung, San-Shan; Hsu, Chia-Ning; Hwang, Chang-Chou; Chen, Wen-Jan

2017-10-01

In recent years, because of the air-spring control technique is more mature, that air- spring suspension systems already can be used to replace the classical vehicle suspension system. Depend on internal pressure variation of the air-spring, thestiffnessand the damping factor can be adjusted. Because of air-spring has highly nonlinear characteristic, therefore it isn’t easy to construct the classical controller to control the air-spring effectively. The paper based on Artificial Neural Network to propose a feasible control strategy. By using offline way for the neural network design and learning to the air-spring in different initial pressures and different loads, offline method through, predict air-spring stiffness parameter to establish a model. Finally, through adjusting air-spring internal pressure to change the K-parameter of the air-spring, realize the well dynamic control performance of air-spring suspension.

Review: The distribution, flow, and quality of Grand Canyon Springs, Arizona (USA)

Science.gov (United States)

Tobin, Benjamin W.; Springer, Abraham E.; Kreamer, David K.; Schenk, Edward

2018-05-01

An understanding of the hydrogeology of Grand Canyon National Park (GRCA) in northern Arizona, USA, is critical for future resource protection. The 750 springs in GRCA provide both perennial and seasonal flow to numerous desert streams, drinking water to wildlife and visitors in an otherwise arid environment, and habitat for rare, endemic and threatened species. Spring behavior and flow patterns represent local and regional patterns in aquifer recharge, reflect the geologic structure and stratigraphy, and are indicators of the overall biotic health of the canyon. These springs, however, are subject to pressures from water supply development, changes in recharge from forest fires and other land management activities, and potential contamination. Roaring Springs is the sole water supply for residents and visitors (>6 million/year), and all springs support valuable riparian habitats with very high species diversity. Most springs flow from the karstic Redwall-Muav aquifer and show seasonal patterns in flow and water chemistry indicative of variable aquifer porosities, including conduit flow. They have Ca/Mg-HCO3 dominated chemistry and trace elements consistent with nearby deep wells drilled into the Redwall-Muav aquifer. Tracer techniques and water-age dating indicate a wide range of residence times for many springs, supporting the concept of multiple porosities. A perched aquifer produces small springs which issue from the contacts between sandstone and shale units, with variable groundwater residence times. Stable isotope data suggest both an elevational and seasonal difference in recharge between North and South Rim springs. This review highlights the complex nature of the groundwater system.

water quality evaluation of spring waters in nsukka, nigeria

African Journals Online (AJOL)

ES Obe

2013-07-02

Jul 2, 2013 ... directly from an underground formation from, which water flows naturally to the surface or from a bored ... evidence that surface runoff is readily entering the spring. This may mean the spring is contaminated with ... soil, hydrological factors that lead to runoff, and by biological processes within the aquatic.

Bio-inspired device: a novel smart MR spring featuring tendril structure

International Nuclear Information System (INIS)

Kaluvan, Suresh; Park, Chun-Yong; Choi, Seung-Bok

2016-01-01

Smart materials such as piezoelectric patches, shape memory alloy, electro and magneto rheological fluid, magnetostrictive materials, etc are involved by far to design intelligent and high performance smart devices like injectors, dental braces, dampers, actuators and sensors. In this paper, an interesting smart device is proposed by inspiring on the structure of the bio climber plant. The key enabling concept of this proposed work is to design the smart spring damper as a helical shaped tendril structure using magneto-rheological (MR) fluid. The proposed smart spring consists of a hollow helical structure filled with MR fluid. The viscosity of the MR fluid decides the damping force of helical shaped smart spring, while the fluid intensity in the vine decides the strength of the tendril in the climber plant. Thus, the proposed smart spring can provide a new concept design of the damper which can be applicable to various damping system industries with tuneable damping force. The proposed smart spring damper has several advantageous such as cost effective, easy implementation compared with the conventional damper. In addition, the proposed spring damper can be easily designed to adapt different damping force levels without any alteration. (letter)

Biomediated Precipitation of Calcium Carbonate in a Slightly Acidic Hot Spring

Science.gov (United States)

Jiang, L.

2015-12-01

A slightly acidic hot spring named "Female Tower" (T=73.5 °C, pH=6.64) is located in the Jifei Geothermal Field, Yunnan Province, Southwest China. The precipitates in the hot spring are composed of large amounts of calcite, aragonite, and sulfur. Scanning electron microscopy (SEM) analyses revealed that the microbial mats were formed of various coccoid, rod-shaped, and filamentous microbes. Transmission electron microscopy (TEM) showed that the intracellular sulfur granules were commonly associated with these microbes. A culture-independent molecular phylogenetic analysis demonstrated that the majority of the bacteria in the spring were sulfur-oxidizing bacteria. In the spring water, H2S concentration was up to 60 ppm, while SO42- concentration was only about 10 ppm. We speculated that H2S might be utilized by sulfur-oxidizing bacteria in this hot spring water, leading to the intracellular formation of sulfur granules. In the meantime, this reaction increased the pH in the micron-scale microdomains, which fostered the precipitation of calcium carbonate in the microbial mats. The results of this study indicated that the sulfur-oxidizing bacteria could play an important role in calcium carbonate precipitation in slightly acidic hot spring environments.

Bio-inspired device: a novel smart MR spring featuring tendril structure

Science.gov (United States)

Kaluvan, Suresh; Park, Chun-Yong; Choi, Seung-Bok

2016-01-01

Smart materials such as piezoelectric patches, shape memory alloy, electro and magneto rheological fluid, magnetostrictive materials, etc are involved by far to design intelligent and high performance smart devices like injectors, dental braces, dampers, actuators and sensors. In this paper, an interesting smart device is proposed by inspiring on the structure of the bio climber plant. The key enabling concept of this proposed work is to design the smart spring damper as a helical shaped tendril structure using magneto-rheological (MR) fluid. The proposed smart spring consists of a hollow helical structure filled with MR fluid. The viscosity of the MR fluid decides the damping force of helical shaped smart spring, while the fluid intensity in the vine decides the strength of the tendril in the climber plant. Thus, the proposed smart spring can provide a new concept design of the damper which can be applicable to various damping system industries with tuneable damping force. The proposed smart spring damper has several advantageous such as cost effective, easy implementation compared with the conventional damper. In addition, the proposed spring damper can be easily designed to adapt different damping force levels without any alteration.

Design optimization and fatigue testing of an electronically-driven mechanically-resonant cantilever spring mechanism

International Nuclear Information System (INIS)

Kheng, Lim Boon; Kean, Koay Loke; Gitano-Briggs, Horizon

2010-01-01

A light scanning device consisting of an electronically-driven mechanically-resonant cantilever spring-mirror system has been developed for innovative lighting applications. The repeated flexing of the cantilever spring during operation can lead to premature fatigue failure. A model was created to optimize the spring design. The optimized spring design can reduce stress by approximately one-third from the initial design. Fatigue testing showed that the optimized spring design can operate continuously for over 1 month without failure. Analysis of failures indicates surface cracks near the root of the spring are responsible for the failures.

Microstructure of Sinter Deposit Formed at Hot Springs in West Sumatera

Science.gov (United States)

Putra, A.; Inanda, D. Y.; Buspa, F.; Salim, A. F.

2018-03-01

Sinter deposit emerged and spread at several hot springs in West Sumatera is divided into three types, they are full silica, half silica-carbonate and full carbonate. This work intends to investigate the characteristic of each type by its crystalline structure and morphology and its correlation to surface temperature. The research is focused on Sapan Maluluang hot spring (full silica), Garara hot spring (half silica-carbonate) and Bawah Kubang hot spring (full carbonate). Crystalline structure is analyzed by X-Ray Diffraction (XRD) methods, it showed that deposit from Sapan Maluluang has opal-A structure, Garara has opal-CT structure and Bawah Kubang has crystalline structure. The Scanning Electron Microscopy (SEM) methods is applied to describe its morphology surface, in which spherical, almost rounded and irregular textured was formed at each deposit, respectively. Surface temperature of hot spring also has given impact on deposit texture.

Experimental Study of Vibration Isolation Characteristics of a Geometric Anti-Spring Isolator

Directory of Open Access Journals (Sweden)

Lixun Yan

2017-07-01

Full Text Available In order to realize low-frequency vibration isolation, a novel geometric anti-spring isolator consisting of several cantilever blade springs are developed in this paper. The optimal design parameters of the geometric anti-spring isolator for different nonlinear geometric parameters are theoretically obtained. The transmissibility characteristic of the geometric anti-spring isolator is investigated through mathematical simulation. A geometric anti-spring isolator with a nonlinear geometric parameter of 0.92 is designed and its vibration isolation performance and nonlinearity characteristic is experimentally studied. The experiment results show that the designed isolator has good low-frequency vibration isolation performance, of which the initial isolation frequency is less than 3.6 Hz when the load weight is 21 kg. The jump phenomena of the response of the isolator under linear frequency sweep excitation are observed, and this result demonstrates that the geometric anti-spring isolator has a complex nonlinearity characteristics with the increment of excitation amplitude. This research work provides a theoretical and experimental basis for the application of the nonlinear geometric anti-spring low-frequency passive vibration isolation technology in engineering practice.

A spring forward for hominin evolution in East Africa.

Science.gov (United States)

Cuthbert, Mark O; Ashley, Gail M

2014-01-01

Groundwater is essential to modern human survival during drought periods. There is also growing geological evidence of springs associated with stone tools and hominin fossils in the East African Rift System (EARS) during a critical period for hominin evolution (from 1.8 Ma). However it is not known how vulnerable these springs may have been to climate variability and whether groundwater availability may have played a part in human evolution. Recent interdisciplinary research at Olduvai Gorge, Tanzania, has documented climate fluctuations attributable to astronomic forcing and the presence of paleosprings directly associated with archaeological sites. Using palaeogeological reconstruction and groundwater modelling of the Olduvai Gorge paleo-catchment, we show how spring discharge was likely linked to East African climate variability of annual to Milankovitch cycle timescales. Under decadal to centennial timescales, spring flow would have been relatively invariant providing good water resource resilience through long droughts. For multi-millennial periods, modelled spring flows lag groundwater recharge by 100 s to 1000 years. The lag creates long buffer periods allowing hominins to adapt to new habitats as potable surface water from rivers or lakes became increasingly scarce. Localised groundwater systems are likely to have been widespread within the EARS providing refugia and intense competition during dry periods, thus being an important factor in natural selection and evolution, as well as a vital resource during hominin dispersal within and out of Africa.

Use of thermal springs for geochemical exploration in Ethiopia ...

African Journals Online (AJOL)

In this study an attempt was made to examine precious metals in the localities of the hydrothermal areas in the central Rift valley with the objective of whether thermal springs can hit mineral deposits. Thus, Filwoha, Sodere, Ambo and Wondogenet thermal spring areas were selected and specimens were collected for gold, ...

Rain-induced spring wheat harvest losses

Science.gov (United States)

Bauer, A.; Black, A. L. (Principal Investigator)

1983-01-01

When rain or a combination of rain and high humidity delay wheat harvest, losses can occur in grain yield and/or grain quality. Yield losses can result from shattering, from reduction in test weight, and in the case of windrowed grain, from rooting of sprouting grain at the soil: windrow contact. Losses in grain quality can result from reduction in test weight and from sprouting. Sprouting causes a degradation of grain proteins and starches, hence flour quality is reduced, and the grain price deteriorates to the value of feed grain. Although losses in grain yield and quality are rain-induced, these losses do not necessarily occur because a standing or windrowed crop is wetted by rain. Spike water concentration in hard red spring wheat must be increased to about 45-49% before sprouting is initiated in grain that has overcome dormancy. The time required to overcome this dormancy after the cultivar has dried to 12 to 14% water concentration differs with hard red spring cultivars. The effect of rain on threshing-ready standing and windrowed hard red spring wheat grain yeild and quality was evaluated. A goal was to develop the capability to forecast the extent of expected loss of grain yield and quality from specific climatic events that delay threshing.

Climatology and classification of spring Saharan cyclone tracks

Energy Technology Data Exchange (ETDEWEB)

Hannachi, A. [Reading University, Department of Meteorology, PO Box 243, Reading (United Kingdom); Awad, A. [King Abdulaziz University, Department of Meteorology, Jeddah (Saudi Arabia); Ammar, K. [Meteorological Authority, Department of Research, Cairo (Egypt)

2011-08-15

Spring Saharan cyclones constitute a dominant feature of the not-well-explored Saharan region. In this manuscript, a climatological analysis and classification of Saharan cyclone tracks are presented using 6-hourly NCEP/NCAR sea level pressure (SLP) reanalyses over the Sahara (10 W-50 E, 20 N-50 N) for the Spring (March-April-May) season over the period 1958-2006. A simple tracking procedure based on following SLP minima is used to construct around 640 Spring Saharan cyclone tracks. Saharan cyclones are found to be short-lived compared to their extratropical counterparts with an e-folding time of about 3 days. The lee side of the west Atlas mountain is found to be the main cyclogenetic region for Spring Saharan cyclones. Central Iraq is identified as the main cyclolytic area. A subjective procedure is used next to classify the cyclone tracks where six clusters are identified. Among these clusters the Western Atlas-Asia Minor is the largest and most stretched, whereas Algerian Sahara-Asia Minor is composed of the most long-lived tracks. Upper level flow associated with the tracks has also been examined and the role of large scale baroclinicity in the growth of Saharan cyclones is discussed. (orig.)

Note: Determination of torsional spring constant of atomic force microscopy cantilevers: Combining normal spring constant and classical beam theory

DEFF Research Database (Denmark)

Álvarez-Asencio, R.; Thormann, Esben; Rutland, M.W.

2013-01-01

A technique has been developed for the calculation of torsional spring constants for AFM cantilevers based on the combination of the normal spring constant and plate/beam theory. It is easy to apply and allow the determination of torsional constants for stiff cantilevers where the thermal power s...... spectrum is difficult to obtain due to the high resonance frequency and low signal/noise ratio. The applicability is shown to be general and this simple approach can thus be used to obtain torsional constants for any beam shaped cantilever. © 2013 AIP Publishing LLC....

The effect of pre spring spray to reduce of citrus important pests.

Science.gov (United States)

Hashemi, B; Damavandian, M R; Shoushtaril, R Vafaei; Tafaghodynia, B

2008-10-01

The importance of pre spring spray against citrus aphids, Pulvinaria aurantii Cockerell and Panonychus citri McGregor that are the most important pest of citrus during spring was tested. In this research, 150 trees ten years old sweet orange (Thomson navel on Citrus aurantium (root stocks)) in a citrus orchard approximately three hectares sampled. The experiment was laid out in a totally randomized (one-way) design replicated five times. According to the results, the pre spring spray do not effect on population density of citrus aphids and P. aurantii during March, April, May and June. However, the P. citri population decreased. Therefore, it seems the pre spring spray in citrus orchards is not necessary, but if P. citri is observed, the pre spring spray should be recommended.

Soda Creek springs - metamorphic waters in the eastern Alaska Range

Science.gov (United States)

Richter, D.H.; Donaldson, D.E.; Lamarre, R.A.

1973-01-01

The Soda Creek springs are a group of small, cold mineral springs on the southern flank of the eastern Alaska Range. The spring waters contain anomalous concentrations of carbon dioxide, sodium, chlorine, sulfate, boron, and ammonia and are actively precipitating deposits of calcite and aragonite. Sparingly present in these deposits are mixed-layer illite-montmorillonite clays and zeolite minerals. Low-temperaturemetamorphic reactions in subjacent marine sedimentary rocks of Jurassic and Cretaceous age may have produced the fluids and silicate minerals. With only a few exceptions, cool bicarbonate-rich springs in Alaska are concentrated south of the Denali fault system in south-central Alaska, southeastern Alaska, and along the Kaltag-Tintina fault system. These areas are characterized by active or recently activetectonism, major faults and folds, and an abundance of marine sedimentary rocks.

Analysis of Spring Development and Gravity Flow System to Capture Water for Local Communities

Directory of Open Access Journals (Sweden)

Adiningrum Cita

2017-01-01

Full Text Available Springs as water sources are relatively inexpensive but highly susceptible to contamination since they are fed by shallow groundwater. Proper spring development helps protect the water from contamination. This study presents an analysis and design of spring development including the type of broncaptering/collecting wall, the dimension for the spring box and the conduction line. In addition, a guideline on “Springwater Construction” published by the Ministry of Public Works has been used in this design. A concentrated spring in Wates, Magelang, Central Java is used as a case study. The design calls for the collection of water from a spring using sets of broncaptering and a spring box, then piping it by gravity a distance of 5.1 kilometers to Van Lith Senior High School. Analysis was done using a manual calculation, which is subsequently compared to the result of HYDROFLO 3 software. Results show that the spring with a flow rate of 0.12 litre/s (manual and 0.17 litre/s (software will be collected into a 5 m3 volume of spring box. The spring box with a +543 m water surface elevation is being supplied to Van Lith +384 m ground elevation using a uniform PVC pipelines with a ¾ inch of diameter.

Long term consumption of mineral spring water containing natural radium-226

International Nuclear Information System (INIS)

Aulenbach, D.B.; Davis, R.E.

1976-01-01

The presence of naturally occurring 226 radium in several of the spring waters of Saratoga Springs, New York has been known for some time. However, recently the recommended maximum acceptable limit for consumption of water containing radium has been lowered to the point that the limits are now lower than the concentration of radium observed in several of the wells. A survey was made of 27 individuals who have consumed water from the Hathorn No. 1 Spring for periods varying from 5-65 years. A calculation was made of the 226 radium body burden from equations provided in the literature. The calcium concentration of the springs was determined in consideration of the still unknown comparative selectivity of the body between radium and calcium. Waters from two of the springs were analzyed for 226 radium using the radon emanation method. No adverse effects of consuming the mineral water were observed in the individuals interviewed nor were there any increased incidences of broken or brittle bones among these individuals

A study on calculation method for mechanical impedance of air spring

International Nuclear Information System (INIS)

Changgeng, Shuai; Penghui, Li; Rustighi, Emiliano

2016-01-01

This paper proposes an approximate analytic method of obtaining the mechanical impedance of air spring. The sound pressure distribution in cylindrical air spring is calculated based on the linear air wave theory. The influences of different boundary conditions on the acoustic pressure field distribution in cylindrical air spring are analysed. A 1-order ordinary differential matrix equation for the state vector of revolutionary shells under internal pressure is derived based on the non-moment theory of elastic thin shell. Referring to the transfer matrix method, a kind of expanded homogeneous capacity high precision integration method is introduced to solve the non-homogeneous matrix differential equation. Combined the solved stress field of shell with the calculated sound pressure field in air spring under the displacement harmonic excitation, the approximate analytical expression of the input and transfer mechanical impedance for the air spring can be achieved. The numerical simulation with the Comsol Multiphysics software verifies the correctness of theoretical analysis result. (paper)

An assessment of the water quality of the Isinuka springs in the ...

African Journals Online (AJOL)

The physico-chemical properties of Isinuka springs, a "wonder" water resource in Port St Johns area of Eastern Cape Province, were investigated over three seasonal regimes. Water samples were collected from the five spring sources, along Isinuka river and from Ferry Point Cottage spring and analysed for their quality ...

Automatic Generation of Setup for CNC Spring Coiler Based on Case-based Reasoning

Institute of Scientific and Technical Information of China (English)

KU Xiangchen; WANG Runxiao; LI Jishun; WANG Dongbo

2006-01-01

When producing special-shape spring in CNC spring coiler, the setup of the coiler is often a manual work using a trial-and-error method. As a result, the setup of coiler consumes so much time and becomes the bottleneck of the spring production process. In order to cope with this situation, this paper proposes an automatic generation system of setup for CNC spring coiler using case-based reasoning (CBR). The core of the study contains: (1) integrated reasoning model of CBR system;(2) spatial shape describe of special-shape spring based on feature;(3) coiling case representation using shape feature matrix; and (4) case similarity measure algorithm. The automatic generation system has implemented with C++ Builder 6.0 and is helpful in improving the automaticity and efficiency of spring coiler.

Development of top nozzle holddown spring for 17x17 next generation fuel assembly

International Nuclear Information System (INIS)

Lee, J. S.; Lee, S. H.; Kim, H. K.; Lee, J. N.; Jeon, K. R.

2002-01-01

Two conceptual holddown spring designs were developed for 17x17 Next Generation Fuel(NGF) top nozzle. One spring pack concept uses three 0.175 inch thick leaves. The other uses four 0.155 inch thick leaves. The room temperature elastic-plastic properties of each spring pack are calculated using the elastic-plastic model derived from classic beam theory and the exiting spring characteristics test. The stress analysis and spring characteristics of each spring pack are also analyzed using FEM(ANSYS 5.7) to verify the elastic-plastic model. The results of the elastic-plastic model have a good agreement to the results of finite element analysis. It is concluded that the 3-leaf 0.175 inch spring pack concept and 4-leaf 0.155 inch spring pack concept are both viable candidates for 17x17 NGF. A series of load-deflection tests will be used to verify the elastic-plastic model and finite element model

Weight compensation characteristics of Armeo®Spring exoskeleton: implications for clinical practice and research.

Science.gov (United States)

Perry, Bonnie E; Evans, Emily K; Stokic, Dobrivoje S

2017-02-17

Armeo®Spring exoskeleton is widely used for upper extremity rehabilitation; however, weight compensation provided by the device appears insufficiently characterized to fully utilize it in clinical and research settings. Weight compensation was quantified by measuring static force in the sagittal plane with a load cell attached to the elbow joint of Armeo®Spring. All upper spring settings were examined in 5° increments at the minimum, maximum, and two intermediate upper and lower module length settings, while keeping the lower spring at minimum. The same measurements were made for minimum upper spring setting and maximum lower spring setting at minimum and maximum module lengths. Weight compensation was plotted against upper module angles, and slope was analyzed for each condition. The Armeo®Spring design prompted defining the slack angle and exoskeleton balance angle, which, depending on spring and length settings, divide the operating range into different unloading and loading regions. Higher spring tensions and shorter module lengths provided greater unloading (≤6.32 kg of support). Weight compensation slope decreased faster with shorter length settings (minimum length = -0.082 ± 0.002 kg/°; maximum length = -0.046 ± 0.001 kg/°) independent of spring settings. Understanding the impact of different settings on the Armeo®Spring weight compensation should help define best clinical practice and improve fidelity of research.

Microbiological and chemical assessment of spring water from a ...

African Journals Online (AJOL)

Assessment of spring water from Ikare-Akoko, a rural setting in southwest, Nigeria for microbial and chemical contaminants was carried out. Total heterotrophic bacteria count of 4.0 x 106 CFU/mL was highest during the peak of the rainy season in Omi-idu spring (Igbede community) while the lowest population of 0.14 x106 ...

Comparative analysis of the flow activity of the Homoljska Potajnica intermittent spring

Directory of Open Access Journals (Sweden)

Igračev Nikola

2014-01-01

Full Text Available Homoljska Potajnica belongs to the type of a very rare, intermittent or rhythmic springs which appear exclusively in karst areas. It is one of the three known springs of this type in Serbia, while it is believed to be only about fifty of these in the rest of the world. As a rare karst and natural phenomenon, Homoljska Potajnica was a subject of interest for numerous researchers and geomorphologists in Serbia. Due to a very complex problem of occurence and the principle of functioning, to get the reliable data of how intemittent springs work, it is neccesarry to provide a continious observations, ussually in a long term period. This paper presents the results of the measurements of spring's flow activity and water discharge, taken in 2012. and 2013. These were carried out for comparison with the results of previous research, with an aim to determine possible changes in dynamics and mechanisms of spring's functioning in the past. One of the goals is to relate the annual precipitation regime with the intensity and frequency of spring activity, to try to determine the specific model of the spring's functioning. Another goal is to emphasize the need for continious observation in order to obtain the relevant data about the evolution of this rare natural phenomenon.

Morphological and phylogenetic diversity of thermophilic cyanobacteria in Algerian hot springs.

Science.gov (United States)

Amarouche-Yala, Samia; Benouadah, Ali; El Ouahab Bentabet, Abd; López-García, Purificación

2014-11-01

Geothermal springs in Algeria have been known since the Roman Empire. They mainly locate in Eastern Algeria and are inhabited by thermophilic organisms, which include cyanobacteria forming mats and concretions. In this work, we have investigated the cyanobacterial diversity of these springs. Cyanobacteria were collected from water, concretions and mats in nine hot springs with water temperatures ranging from 39 to 93 °C. Samples were collected for isolation in culture, microscopic morphological examination, and molecular diversity analysis based on 16S rRNA gene sequences. Nineteen different cyanobacterial morphotypes were identified, the most abundant of which were three species of Leptolyngbya, accompanied by members of the genera Gloeocapsa, Gloeocapsopsis, Stigonema, Fischerella, Synechocystis, Microcoleus, Cyanobacterium, Chroococcus and Geitlerinema. Molecular diversity analyses were in good general agreement with classical identification and allowed the detection of additional species in three springs with temperatures higher than 50 °C. They corresponded to a Synechococcus clade and to relatives of the intracellularly calcifying Candidatus Gloeomargarita lithophora. The hottest springs were dominated by members of Leptolyngbya, Synechococcus-like cyanobacteria and Gloeomargarita, whereas Oscillatoriales other than Leptolyngbya, Chroococcales and Stigonematales dominated lower temperature springs. The isolation of some of these strains sets the ground for future studies on the biology of thermophilic cyanobacteria.

Estimating Spring Condensation on the Great Lakes

Science.gov (United States)

Meyer, A.; Welp, L.

2017-12-01

The Laurentian Great Lakes region provides opportunities for shipping, recreation, and consumptive water use to a large part of the United States and Canada. Water levels in the lakes fluctuate yearly, but attempts to model the system are inadequate because the water and energy budgets are still not fully understood. For example, water levels in the Great Lakes experienced a 15-year low period ending in 2013, the recovery of which has been attributed partially to decreased evaporation and increased precipitation and runoff. Unlike precipitation, the exchange of water vapor between the lake and the atmosphere through evaporation or condensation is difficult to measure directly. However, estimates have been constructed using off-shore eddy covariance direct measurements of latent heat fluxes, remote sensing observations, and a small network of monitoring buoys. When the lake surface temperature is colder than air temperature as it is in spring, condensation is larger than evaporation. This is a relatively small component of the net annual water budget of the lakes, but the total amount of condensation may be important for seasonal energy fluxes and atmospheric deposition of pollutants and nutrients to the lakes. Seasonal energy fluxes determine, and are influenced by, ice cover, water and air temperatures, and evaporation in the Great Lakes. We aim to quantify the amount of spring condensation on the Great Lakes using the National Center for Atmospheric Prediction North American Regional Reanalysis (NCEP NARR) Data for Winter 2013 to Spring 2017 and compare the condensation values of spring seasons following high volume, high duration and low volume, low duration ice cover.

An adjustment in NiTi closed coil spring for an extended range of activation.

Science.gov (United States)

Ravipati, Raghu Ram; Sivakumar, Arunachalam; Sudhakar, P; Padmapriya, C V; Bhaskar, Mummudi; Azharuddin, Mohammad

2014-01-01

The Nickel Titanium (NiTi) closed coil springs serve as an efficient force delivery system in orthodontic space closure mechanics. The closed coil springs with the eyelets come in various lengths to broaden its force characteristics for an expedient space closure. However, at a certain point of time of progressive space closure, the coil spring can be expanded no further for an adequate force delivery. In such situations, the clinician prefers to replace the existing spring with another short length spring. The present article describes a simple conservative technique for progressively re-activating the same NiTi closed coil spring for complete space closure.

Fuel column retainer using radially compressed spring

International Nuclear Information System (INIS)

Johansson, E.B.

1989-01-01

This patent describes a fuel rod construction including a fuel rod having an inside cylindrical diameter, cylindrical fuel pellets placed within the rod. The cylindrical fuel pellets having a diameter less than the inside cylindrical diameter and being stacked end to end for a distance less than the length of the fuel rod inside the fuel rod; Zircaloy end plugs for sealing the rod at either end; a compression spring adjacent one end of the rods for biasing the pellets to and towards the other end of the rod. An improvement in the Zircaloy spring is described

The HISH-alliance and the Arab spring

DEFF Research Database (Denmark)

Dandan, Salem Ben Souhail

, in terms of relative strength, as being essential in understanding the alliance. It then goes on to look at what the Arab-spring has so far meant for the different actors and how this has impacted the alliance. It is argued that the ability of the non-state armed entities, Hezbollah and Hamas...... within the global community, due to the current systemic situation and the Arab-spring. In short, the paper aims to establish a correlation between the international and regional changes, the newly found autonomy of the non-state entities and the decreasing capabilities of the states, in order...

A bead-spring chain as a one-dimensional polyelectrolyte gel.

Science.gov (United States)

Manning, Gerald S

2018-05-23

The physical principles underlying expansion of a single-chain polyelectrolyte coil caused by Coulomb repulsions among its ionized groups, and the expansion of a cross-linked polyelectrolyte gel, are probably the same. In this paper, we analyze a "one-dimensional" version of a gel, namely, a linear chain of charged beads connected by Hooke's law springs. In the Debye-Hückel range of relatively weak Coulomb strength, where counterion condensation does not occur, the springs are realistically stretched on a nanolength scale by the repulsive interactions among the beads, if we use a spring constant normalized by the inverse square of the solvent Bjerrum length. The persistence length and radius of gyration counter-intuitively decrease when Coulomb strength is increased, if analyzed in the framework of an OSF-type theory; however, a buckling theory generates the increase that is consistent with bead-spring simulations.

Elk Distributions Relative to Spring Normalized Difference Vegetation Index Values

International Nuclear Information System (INIS)

Smallidge, S.T.; Baker, T.T.; VanLeeuwen, D.; Gould, W.R.; Thompson, B.C.

2010-01-01

Rocky Mountain elk (Cervus elaphus) that winter near San Antonio Mountain in northern New Mexico provide important recreational and economic benefits while creating management challenges related to temporospatial variation in their spring movements. Our objective was to examine spring distributions of elk in relation to vegetative emergence as it progresses across the landscape as measured by remote sensing. Spring distributions of elk were closely associated with greater photosynthetic activity of spring vegetation in 2 of 3 years as determined using NDVI values derived from AVHRR datasets. Observed elk locations were up to 271% greater than expected in the category representing the most photosynthetic activity. This association was not observed when analyses at a finer geographic scale were conducted. Managers facing challenges involving human-wildlife interactions and land-use issues should consider environmental conditions that may influence variation in elk association with greener portions of the landscape.

Effect of temperature on the orthodontic clinical applications of niti closed-coil springs

Science.gov (United States)

Espinar-Escalona, Eduardo; Llamas-Carreras, José M.; Barrera-Mora, José M.; Abalos-Lasbrucci, Camilo

2013-01-01

NiTi spring coils were used to obtain large deformation under a constant force. The device consists on a NiTi coil spring, superelastic at body temperature, in order to have a stress plateau during the austenitic retransformation during the unloading. The temperature variations induced changes in the spring force. Objectives: The aim of this study is to investigate the effect of the temperature variations in the spring forces and corrosion behaviour simulating the ingestion hot/cold drinks and food. Study Design: The springs were subjected to a tensile force using universal testing machine MTS-Adamel (100 N load cell). All tests were performed in artificial saliva maintained at different temperatures. The corrosion tests were performed according to the ISO-standard 10993-15:2000. Results: The increase in temperature of 18oC induced an increase in the spring force of 30%. However, when the temperature returns to 37oC the distraction force recovers near the initial level. After cooling down the spring to 15oC, the force decreased by 46%. This investigation show as the temperature increase, the corrosion potential shifts towards negative values and the corrosion density is rising. Conclusions: The changes of the temperatures do not modify the superelastic behaviour of the NiTi closed-coil springs. The corrosion potential of NiTi in artificial saliva is decreasing by the rise of the temperatures. Key words:Superelasticity, NiTi, springs, orthodontic, coils, recovery, temperature. PMID:23722142

Fossilization processes in siliceous thermal springs: trends in preservation along thermal gradients

Science.gov (United States)

Cady, S. L.; Farmer, J. D.

1996-01-01

To enhance our ability to extract palaeobiological and palaeoenvironmental information from ancient thermal spring deposits, we have studied the processes responsible for the development and preservation of stromatolites in modern subaerial thermal spring systems in Yellowstone National Park (USA). We investigated specimens collected from silica-depositing thermal springs along the thermal gradient using petrographic techniques and scanning electron microscopy. Although it is known that thermophilic cyanobacteria control the morphogenesis of thermal spring stromatolites below 73 degrees C, we have found that biofilms which contain filamentous thermophiles contribute to the microstructural development of subaerial geyserites that occur along the inner rims of thermal spring pools and geyser effluents. Biofilms intermittently colonize the surfaces of subaerial geyserites and provide a favoured substrate for opaline silica precipitation. We have also found that the preservation of biotically produced microfabrics of thermal spring sinters reflects dynamic balances between rates of population growth, decomposition of organic matter, silica deposition and early diagenesis. Major trends in preservation of thermophilic organisms along the thermal gradient are defined by differences in the mode of fossilization, including replacement, encrustation and permineralization.

Carbonate ion-enriched hot spring water promotes skin wound healing in nude rats.

Directory of Open Access Journals (Sweden)

Jingyan Liang

Full Text Available Hot spring or hot spa bathing (Onsen is a traditional therapy for the treatment of certain ailments. There is a common belief that hot spring bathing has therapeutic effects for wound healing, yet the underlying molecular mechanisms remain unclear. To examine this hypothesis, we investigated the effects of Nagano hot spring water (rich in carbonate ion, 42°C on the healing process of the skin using a nude rat skin wound model. We found that hot spring bathing led to an enhanced healing speed compared to both the unbathed and hot-water (42°C control groups. Histologically, the hot spring water group showed increased vessel density and reduced inflammatory cells in the granulation tissue of the wound area. Real-time RT-PCR analysis along with zymography revealed that the wound area of the hot spring water group exhibited a higher expression of matrix metalloproteinases-2 and -9 compared to the two other control groups. Furthermore, we found that the enhanced wound healing process induced by the carbonate ion-enriched hot spring water was mediated by thermal insulation and moisture maintenance. Our results provide the evidence that carbonate ion-enriched hot spring water is beneficial for the treatment of skin wounds.

Compacted cancellous bone has a spring-back effect

DEFF Research Database (Denmark)

Kold, S; Bechtold, JE; Ding, Ming

2003-01-01

A new surgical technique, compaction, has been shown to improve implant fixation. It has been speculated that the enhanced implant fixation with compaction could be due to a spring-back effect of compacted bone. However, such an effect has yet to be shown. Therefore we investigated in a canine mo....... Thus we found a spring-back effect of compacted bone, which may be important for increasing implant fixation by reducing initial gaps between the implant and bone....

Coastal Energy Corporation, Willow Springs, MO

Science.gov (United States)

notice of a proposed Administrative Penalty Assessment against Coastal Energy Corporation, located at 232 Burnham Road, Willow Springs, Missouri, for alleged violations at the facility located at or near that facility.

The 2010 spring drought reduced primary productivity in southwestern China

International Nuclear Information System (INIS)

Zhang Li; Li Jing; Xiao Jingfeng; Wang Kun; Lei Liping; Guo Huadong

2012-01-01

Many parts of the world experience frequent and severe droughts. Summer drought can significantly reduce primary productivity and carbon sequestration capacity. The impacts of spring droughts, however, have received much less attention. A severe and sustained spring drought occurred in southwestern China in 2010. Here we examine the influence of this spring drought on the primary productivity of terrestrial ecosystems using data on climate, vegetation greenness and productivity. We first assess the spatial extent, duration and severity of the drought using precipitation data and the Palmer drought severity index. We then examine the impacts of the drought on terrestrial ecosystems using satellite data for the period 2000–2010. Our results show that the spring drought substantially reduced the enhanced vegetation index (EVI) and gross primary productivity (GPP) during spring 2010 (March–May). Both EVI and GPP also substantially declined in the summer and did not fully recover from the drought stress until August. The drought reduced regional annual GPP and net primary productivity (NPP) in 2010 by 65 and 46 Tg C yr −1 , respectively. Both annual GPP and NPP in 2010 were the lowest over the period 2000–2010. The negative effects of the drought on annual primary productivity were partly offset by the remarkably high productivity in August and September caused by the exceptionally wet conditions in late summer and early fall and the farming practices adopted to mitigate drought effects. Our results show that, like summer droughts, spring droughts can also have significant impacts on vegetation productivity and terrestrial carbon cycling. (letter)

Increased spring freezing vulnerability for alpine shrubs under early snowmelt.

Science.gov (United States)

Wheeler, J A; Hoch, G; Cortés, A J; Sedlacek, J; Wipf, S; Rixen, C

2014-05-01

Alpine dwarf shrub communities are phenologically linked with snowmelt timing, so early spring exposure may increase risk of freezing damage during early development, and consequently reduce seasonal growth. We examined whether environmental factors (duration of snow cover, elevation) influenced size and the vulnerability of shrubs to spring freezing along elevational gradients and snow microhabitats by modelling the past frequency of spring freezing events. We sampled biomass and measured the size of Salix herbacea, Vaccinium myrtillus, Vaccinium uliginosum and Loiseleuria procumbens in late spring. Leaves were exposed to freezing temperatures to determine the temperature at which 50% of specimens are killed for each species and sampling site. By linking site snowmelt and temperatures to long-term climate measurements, we extrapolated the frequency of spring freezing events at each elevation, snow microhabitat and per species over 37 years. Snowmelt timing was significantly driven by microhabitat effects, but was independent of elevation. Shrub growth was neither enhanced nor reduced by earlier snowmelt, but decreased with elevation. Freezing resistance was strongly species dependent, and did not differ along the elevation or snowmelt gradient. Microclimate extrapolation suggested that potentially lethal freezing events (in May and June) occurred for three of the four species examined. Freezing events never occurred on late snow beds, and increased in frequency with earlier snowmelt and higher elevation. Extrapolated freezing events showed a slight, non-significant increase over the 37-year record. We suggest that earlier snowmelt does not enhance growth in four dominant alpine shrubs, but increases the risk of lethal spring freezing exposure for less freezing-resistant species.

Geologic setting and chemical characteristics of hot springs in central and western Alaska

Science.gov (United States)

Miller, Thomas P.; Barnes, Ivan; Pattan, William Wallace

1973-01-01

Numerous hot springs occur in a variety of geologic provinces in central and western Alaska. Granitic plutons are common to all the provinces and the hot springs are spatially associated with the contacts of these plutons. Of 23 hot springs whose bedrock geology is known, all occur within 3 miles of a granitic pluton. The occurrence of hot springs, however, appears to be independent of the age, composition, or magmatic history of the pluton.

A study on mechanical properties and flow-induced vibrations of coil-shaped holddown spring

International Nuclear Information System (INIS)

Kim, Kyu-Tae

2010-01-01

The fuel assemblies used in the OPR1000s in Korea employ four coil-shaped hold-down springs to exert compressive load at the top of fuel assembly so that the assemblies may not be damaged by preventing its hydraulic-induced lifting-off from its lower seating surface. However, the coolant flow generates the flow-induced vibration at the coil-shaped hold-down springs which may cause wear on the spring surfaces. A hold-own spring may be fractured if torsional stress acting on its worn area exceeds a stress limit, resulting in the loss of hold-down spring force of the fuel assembly. In this paper, flow-induced vibration tests were performed for standard and improved coil type hold-down springs to investigate the effects of these two hold-down spring designs on flow-induced vibration wear. In parallel, a wide spectrum of mechanical tests was performed to obtain vibration-related characteristics of these two hold-down springs, which can be used as input data for the fuel assembly static and dynamic analysis. It is found that the improved hold-down spring design is better against flow-induced vibration wear than the standard one. With the use of the three-dimensional Solidwork model, the stress-related design lifetime of the improved hold-down spring was estimated by extrapolating its wear data measured from the flow-induced vibration tests, which indicates that the improved HD spring design will maintain integrity during the fuel design lifetime in OPR1000s in Korea.

Automated cycled sprinkler irrigation for spring frost protection of cranberries

Science.gov (United States)

Sprinkler irrigation is essential for preventing spring frost bud damage in cranberry (Vaccinium macrocarpon Ait). Risk-averse growers have been reluctant to adopt the intermittent cycling of irrigation pumps as a standard management practice. In the spring of 2013 and 2014, an experiment was conduc...

Remote access and automation of SPring-8 MX beamlines

Energy Technology Data Exchange (ETDEWEB)

Ueno, Go, E-mail: ueno@spring8.or.jp; Hikima, Takaaki; Yamashita, Keitaro; Hirata, Kunio; Yamamoto, Masaki [RIKEN SPring-8 Center, 1-1-1 Koto, Sayo-cho, Sayo-gun, Hyogo 679-5148 JAPAN (Japan); Hasegawa, Kazuya; Murakami, Hironori; Furukawa, Yukito; Mizuno, Nobuhiro; Kumasaka, Takashi [SPring-8/JASRI, 1-1-1 Koto, Sayo-cho, Sayo-gun, Hyogo 679-5198 JAPAN (Japan)

2016-07-27

At SPring-8 MX beamlines, a remote access system has been developed and started user operation in 2010. The system has been developed based on an automated data collection and data management architecture utilized for the confirmed scheme of SPring-8 mail-in data collection. Currently, further improvement to the remote access and automation which covers data processing and analysis are being developed.

Community microrespirometry and molecular analyses reveal a diverse energy economy in Great Boiling Spring and Sandy's Spring West in the U.S. Great Basin.

Science.gov (United States)

Murphy, Caitlin N; Dodsworth, Jeremy A; Babbitt, Aaron B; Hedlund, Brian P

2013-05-01

Microrespirometry showed that several organic and inorganic electron donors stimulated oxygen consumption in two ∼80°C springs. Sediment and planktonic communities were structurally and functionally distinct, and quantitative PCR revealed catabolically distinct subpopulations of Thermocrinis. This study suggests that a variety of chemolithotrophic metabolisms operate simultaneously in these springs.

Lanthanoid abundance of some neutral hot spring waters in Japan

International Nuclear Information System (INIS)

Kikawada, Yoshikazu; Oi, Takao; Honda, Teruyuki

1999-01-01

Contents of lanthanoids (Ln's) in some neutral hot spring waters as well as in acidic hot spring waters were determined by neutron activation analysis. It was found that a higher pH resulted in lower concentrations of Ln's; the value of correlation coefficient (r) between the logarithm of the concentration of Sm ([Sm]), chosen as the representative of Ln's, and the logarithm of pH was -0.90. The sum of [Al] and [Fe] was strongly correlated with [Ln]'s in the pH range of 1.3 and 8.8; the correlation was expressed as log[Sm] = 0.893 log([Al] + [Fe]) - 5.45 with the r value of 0.98. The sum of [Al] and [Fe] was thus a good measure of the Ln contents in acidic and neutral hot spring waters. The Ln abundance patterns of neutral hot spring waters with normal CO 2 concentrations had concave shapes with relative depletion in the middle-heavy Ln's and seemed to reflect the solubility of Ln carbonates. The neutral hot spring water with a high CO 2 content of 1,800 ppm showed a Ln pattern with a relative enrichment in the heavy Ln's and seemed to reflect the solubility of Ln's observed for CO 2 -rich solutions. (author)

Geologic report for the Weldon Spring Raffinate Pits Site

International Nuclear Information System (INIS)

1984-10-01

A preliminary geologic site characterization study was conducted at the Weldon Spring Raffinate Pits Site, which is part of the Weldon Spring Site, in St. Charles County, Missouri. The Raffinate Pits Site is under the custody of the Department of Energy (DOE). Surrounding properties, including the Weldon Spring chemical plant, are under the control of the Department of the Army. The study determined the following parameters: site stratigraphy, lithology and general conditions of each stratigraphic unit, and groundwater characteristics and their relation to the geology. These parameters were used to evaluate the potential of the site to adequately store low-level radioactive wastes. The site investigation included trenching, geophysical surveying, borehole drilling and sampling, and installing observation wells and piezometers to monitor groundwater and pore pressures

Hydrochemical Characteristics and Formation of the Saline or Salty Springs in Eastern Sichuan Basin of China

Science.gov (United States)

Zhou, X.

2017-12-01

Saline or salty springs provide important information on the hydrogeochemical processes and hydrology within subsurface aquifers. More than 20 saline and salty springs occur in the core of anticlines in the eastern Sichuan Basin in southwestern China where the Lower and Middle Triassic carbonates outcrop. Water samples of 8 saline and salty springs (including one saline hot spring) were collected for analyses of the major and minor constituents, trace elements and stable oxygen and hydrogen isotopes. The TDS of the springs range from 4 to 83 g/L, and they are mainly of Cl-Na type. Sr, Ba and Li are the predominant trace elements. The δ2H and δ18O of the water samples indicate that they are of meteoric origin. The source of salinity of the springs originates from dissolution of minerals in the carbonates, including halite, gypsum, calcite and dolomite. The formation mechanism of the springs is that groundwater receives recharge from infiltration of precipitation, undergoes shallow or deep circulation in the core of the anticline and incongruent dissolution of the salt-bearing carbonates occurs, and emerges in the river valley in the form of springs with relatively high TDS. The 8 springs can be classified into 4 springs of shallow groundwater circulation and 4 springs of deep groundwater circulation according to the depth of groundwater circulation, 7 springs of normal temperature and 1 hot spring according to temperature. There are also 2 up-flow springs: the carbonate aquifers are overlain by relatively impervious sandstone and shale, groundwater may flows up to the ground surface through the local portion of the overlying aquiclude where fractures were relatively well developed, and emerges as an up-flow spring. Knowledge of the hydrochemical characteristics and the geneses of the saline and salty springs are of important significance for the utilization and preservation of the springs.

The study on stress-strain state of the spring at high temperature using ABAQUS

Directory of Open Access Journals (Sweden)

H Sun

2014-01-01

Full Text Available Cylindrical helical springs are widely used in the elements of thermal energy devices. It is necessary to guarantee the stability of the stress state of spring in high temperature. Relaxation phenomenon of stress is studied in this paper. Calculations are carried out in the environment of ABAQUS. The verification is taken out using analytical calculations.This paper describes the distribution and character of stress contour lines on the cross section of spring under the condition of instantaneous load, explicates the relaxation law with time. Research object is cylindrical helical spring, that working at high temperature. The purpose of this work is to get the stress relaxation law of spring, and to guarantee the long-term strength.This article presents the basic theory of helical spring. Establishes spring mathematical model of creep under the loads of compression and torsion. The stress formulas of each component in the cross section of spring are given. The calculation process of relaxation is analyzed in the program ABAQUS.In this paper compare the analytical formulas of spring stress with the simulation results, which are created by program ABAQUS.Finite element model for stress creep analysis in the cross section is created, material of spring – stainless steel 10X18N9T, springs are used at the temperature 650℃.At the beginning, stress-stain of spring is in the elastic state. Analyzes the change law of creep stress under the condition of constant load and a fixed compression.When analyzing under the condition of a fixed compression, the stresses are quickly decreased in most area in the cross section of spring, and the point of minimum shear stress gradually moves to the direction of outer diameter, because of this, stresses in a small area near the center increase slowly at first then decrease gradually with time. When analyzing under the condition of constant load, the stresses are quickly decreased in the around area and in creased

Non-linear Springing Excitation Due to a Bidirectional Wave Field

DEFF Research Database (Denmark)

Vidic-Perunovic, Jelena; Jensen, Jørgen Juncher

2005-01-01

Significant springing vibrations in ships have recently been measured in a large ocean-going bulk carrier. So far calculations using various linear and non-linear hydrodynamic procedures have not been able to predict the measured responses. In the present paper it is shown that the springing...

New Approaches for Responsible Management of Offshore Springs in Semi-arid Regions

Science.gov (United States)

Shaban, Amin; de Jong, Carmen; Al-Sulaimani, Zaher

2017-04-01

In arid and semi-arid regions, such as the Mediterranean and Gulf Region where water is scarce water demand has been exacerbated and become a major environmental challenge. Presently there is massive pressure to develop new water sources to alleviate existing water stress. In the quest for more freshwater even groundwater discharge into the sea in the form of "off-shore freshwater springs" (or submarine groundwater discharge) has been contemplated as a potential source of unconventional water in coastal zones. Offshore-springs are derived from aquifers with complex geological controls mainly in the form of faults and karst conduits. Representing a border-line discipline, they have been poorly studied with only few submarine groundwater monitoring sites existing worldwide. Recently, innovative techniques have been developed enabling springs to be detected via remote sensing such as airborne surveys or satellite images. "Thermal Anomalies" can be clearly identified as evidence for groundwater discharge into the marine environment. A diversity of groundwater routes along which off-shore springs are fed from land sources can be recognized and near-shore and offshore springs differentiated and classified according to their geometry. This is well pronounced along the coast of Lebanon and offshore of Oman. Offshore springs play an important role in the marine ecosystem as natural sources of mercury, metals, nutrients, dissolved carbon species and in cooling or warming ocean water. However, they are extremely sensitive to variations in qualitative and quantitative water inputs triggered by climate change and anthropogenic impacts especially in their recharge zones. Pollutants such as sewage, detergents, heavy metals or herbicides that negatively affect water quality of offshore springs can transit the groundwater rapidly. Recently these springs have also been severely affected by uncontrolled water abstraction from land aquifers. In Bahrain, overpumping combined with

HYDROGEOCHEMICAL CHARACTERISTICS OF THE ST. IVAN SPRING IN ISTRIA, CROATIA

Directory of Open Access Journals (Sweden)

Tatjana Vlahović

2000-12-01

Full Text Available In addition to geological, hydrogeological investigations and groundwater tracing, detailed surveying of the groundwater quality is becoming particularly important for environmental impact monitoring on karst aquifers. Groundwater quality data contain two types of information i.e. the natural chemistry of water and its modifications caused by antropogenic impacts. The method of results presentation as well as the importance of water quality surveying particularly with respect to the indicators showing its natural chemistry, are shown here exemplified by the St. Ivan spring in Istria, Croatia. Natural chemistry of the groundwater is a consequence of hydrogeochemical facies, and it is used here for interpretation of spring generating conditions and the origin of groundwater. Results obtained so far confirm that the extent of recharge area of the spring change in dependence of the hydrological conditions. Hydrogeochemical characteristics of the spring are presented graphically in the form of correlation diagrams showing major groundwater parameters, saturation conditions and trends of particular parameters as a function of time.

MODELLING AND FAILURE ANALYSIS OF FLEXURE SPRINGS FOR A STIRLING CRYOCOOLER

Directory of Open Access Journals (Sweden)

RAJESH V. R.

2017-04-01

Full Text Available In the range of milliwatt to a few watts cooling capacity, Stirling cycle and pulse tube coolers are most suitable for producing cryogenic temperatures owing to their eco-friendliness, high efficiency, cooling capacity to mass ratio etc. The compressor of a Stirling cooler is powered by a linear motor. The power piston of the cooler is held in position and moves to and fro with the support of so called flexure springs or flexure bearings. Flexures avoid direct contact between moving parts of the compressor of the cooler. Thus, if designed adequately to withstand fatigue, flexure bearings can easily outlast rolling element bearings and slider bearings. In this work, a computational analysis is used to study the performance of flexure spring by varying the geometrical parameters. Three of the most common spring materials namely, SS304, beryllium copper and spring steel are considered for analysis. The analysis was made by varying the parameters like spiral sweep angle, slot width, number of spirals and disc thickness. The influence of each of these parameters on the fatigue life of the spring has been investigated. The results suggest that flexure springs of three spiral arms would be the ideal choice for the selected cryocooler. The variation of stress developed with respect to different design parameters and fatigue damage factor are presented graphically.

Toxic cyanobacteria and cyanotoxins in public hot springs in Saudi Arabia.

Science.gov (United States)

Mohamed, Zakaria A

2008-01-01

Toxic cyanobacteria are well reported in rivers, lakes and even marine environments, but the toxin production of cyanobacteria in hot springs is largely unexplored. Therefore, the present study investigated the presence of toxic cyanobacteria and cyanotoxins in public hot springs in Saudi Arabia. The results of an enzyme-linked immunosorbent assay (ELISA) revealed that Saudi spring cyanobacterial mats contained microcystins (MCYSTs) at concentrations ranging from 468 to 512.5 microg g(-1). The Limulus amebocyte lystae (LAL) assay detected lipopolysaccharide (LPS) endotoxins in these mats at concentrations ranging from 433.3 to 506.8 EU g(-1). MCYSTs and endotoxins were also detected in spring waters at levels of 5.7 microg l(-1) and 640 EU ml(-1), respectively, exceeding WHO's provisional guideline value for MCYST-LR in drinking-water. High-performance liquid chromatography (HPLC) analysis revealed that only Oscillatoria limosa and Synechococcus lividus can produce MCYSTs with a profile consisting of MCYST-RR and -LR. Based on the LAL assay, 12 out of 17 cyanobacterial species contained LPS at concentrations ranging from 0.93 to 21.06 EU g(-1). However, not all LPS of these species were toxic to mice. This study suggests that the hot springs in the world including Saudi Arabia should be screened for toxic cyanobacteria to avoid the exposure of people recreating and bathing in spring waters to cyanobacterial toxins.

Microbial diversity and autotrophic activity in Kamchatka hot springs.

Science.gov (United States)

Merkel, Alexander Yu; Pimenov, Nikolay V; Rusanov, Igor I; Slobodkin, Alexander I; Slobodkina, Galina B; Tarnovetckii, Ivan Yu; Frolov, Evgeny N; Dubin, Arseny V; Perevalova, Anna A; Bonch-Osmolovskaya, Elizaveta A

2017-03-01

Microbial communities of Kamchatka Peninsula terrestrial hot springs were studied using molecular, radioisotopic and cultural approaches. Analysis of 16S rRNA gene fragments performed by means of high-throughput sequencing revealed that aerobic autotrophic sulfur-oxidizing bacteria of the genus Sulfurihydrogenibium (phylum Aquificae) dominated in a majority of streamers. Another widely distributed and abundant group was that of anaerobic bacteria of the genus Caldimicrobium (phylum Thermodesulfobacteria). Archaea of the genus Vulcanisaeta were abundant in a high-temperature, slightly acidic hot spring, where they were accompanied by numerous Nanoarchaeota, while the domination of uncultured Thermoplasmataceae A10 was characteristic for moderately thermophilic acidic habitats. The highest rates of inorganic carbon assimilation determined by the in situ incubation of samples in the presence of 14 C-labeled bicarbonate were found in oxygen-dependent streamers; in two sediment samples taken from the hottest springs this process, though much weaker, was found to be not dependent on oxygen. The isolation of anaerobic lithoautotrophic prokaryotes from Kamchatka hot springs revealed a wide distribution of the ability for sulfur disproportionation, a new lithoautotrophic process capable to fuel autonomous anaerobic ecosystems.

Clinical Course of Homozygous Hemoglobin Constant Spring in Pediatric Patients.

Science.gov (United States)

Komvilaisak, Patcharee; Jetsrisuparb, Arunee; Fucharoen, Goonnapa; Komwilaisak, Ratana; Jirapradittha, Junya; Kiatchoosakun, Pakaphan

2018-04-17

Hemoglobin (Hb) Constant Spring is an alpha-globin gene variant due to a mutation of the stop codon resulting in the elongation of the encoded polypeptide from 141 to 172 amino acid residues. Patients with homozygous Hb Constant Spring are usually mildly anemic. We retrospectively describe clinical manifestations, diagnosis, laboratory investigations, treatment, and associated findings in pediatric patients with homozygous Hb Constant Spring followed-up at Srinagarind Hospital. Sixteen pediatric cases (5 males and 11 females) were diagnosed in utero (N=6) or postnatal (n=10). Eleven cases were diagnosed with homozygous Hb Constant Spring, 4 with homozygous Hb Constant Spring with heterozygous Hb E, and 1 with homozygous Hb Constant Spring with homozygous Hb E. Three cases were delivered preterm. Six patients had low birth weights. Clinical manifestations included fetal anemia in 6 cases, hepatomegaly in 1 case, hepatosplenomegaly in 2 cases, splenomegaly in 1 case. Twelve cases exhibited early neonatal jaundice, 9 of which required phototherapy. Six cases received red cell transfusions; 1 (3), >1 (3). After the first few months of life, almost all patients had mild microcytic hypochromic anemia and an increased reticulocyte count with a wide red cell distribution (RDW), but no longer required red cell transfusion. At 1 to 2 years of age, some patients still had mild microcytic hypochromic anemia and some had normocytic hypochromic anemia with Hb around 10 g/dL, increased reticulocyte count and wide RDW. Associated findings included hypothyroidism (2), congenital heart diseases (4), genitourinary abnormalities (3), gastrointestinal abnormalities (2), and developmental delay (1). Pediatric patients with homozygous Hb Constant Spring developed severe anemia in utero and up to the age of 2 to 3 months postnatal, requiring blood transfusions. Subsequently, their anemia was mild with no evidence of hepatosplenomegaly. Their Hb level was above 9 g/dL with hypochromic

Field observations and management strategy for hot spring wastewater in Wulai area, Taiwan.

Science.gov (United States)

Lin, J Y; Chen, C F; Lei, F R; Hsieh, C D

2010-01-01

Hot springs are important centers for recreation and tourism. However, the pollution that may potentially be caused by hot spring wastewater has rarely been discussed. More than half of Taiwan's hot springs are located in areas where the water quality of water bodies is to be protected, and untreated wastewater could pollute the receiving water bodies. In this study, we investigate hot spring wastewater in the Wulai area, one of Taiwan's famous hot spring resorts. Used water from five hot spring hotels was sampled and ten sampling events were carried out to evaluate the changes in the quality of used water in different seasons, at different periods of the week, and from different types of hotels. The concentrations of different pollutants in hot spring wastewater were found to exhibit wide variations, as follows: COD, 10-250 mg/L; SS, N.D.-93 mg/L; NH(3)-N, 0.01-1.93 mg/L; TP, 0.01-0.45 mg/L; and E. coli, 10-27,500 CFU/100 mL. The quality of hot spring wastewater depends on the operation of public pools, because this affects the frequency of supplementary fresh water and the outflow volume. Two management strategies, namely, onsite treatment systems and individually packaged treatment equipment, are considered, and a multi-objective optimization model is used to determine the optimal strategy.

Thermomechanical behavior of NiTiPdPt high temperature shape memory alloy springs

International Nuclear Information System (INIS)

Nicholson, D E; Vaidyanathan, R; Padula II, S A; Noebe, R D; Benafan, O

2014-01-01

Transformation strains in high temperature shape memory alloys (HTSMAs) are generally smaller than for conventional NiTi alloys and can be purposefully limited in cases where stability and repeatability at elevated temperatures are desired. Yet such alloys can still be used in actuator applications that require large strokes when used in the form of springs. Thus there is a need to understand the thermomechanical behavior of shape memory alloy spring actuators, particularly those consisting of alternative alloys. In this work, a modular test setup was assembled with the objective of acquiring stroke, stress, temperature, and moment data in real time during joule heating and forced convective cooling of Ni 19.5 Ti 50.5 Pd 25 Pt 5 HTSMA springs. The spring actuators were subjected to both monotonic axial loading and thermomechanical cycling. The role of rotational constraints (i.e., by restricting rotation or allowing for free rotation at the ends of the springs) on stroke performance was also assessed. Finally, recognizing that evolution in the material microstructure can result in changes in HTSMA spring geometry, the effect of material microstructural evolution on spring performance was examined. This was done by taking into consideration the changes in geometry that occurred during thermomechanical cycling. This work thus provides insight into designing with HTSMA springs and predicting their thermomechanical performance. (paper)

Biological Characterization of Microenvironments in a Hypersaline Cold Spring Mars Analog

Directory of Open Access Journals (Sweden)

Haley M. Sapers

2017-12-01

Full Text Available While many habitable niches on Earth are characterized by permanently cold conditions, little is known about the spatial structure of seasonal communities and the importance of substrate-cell associations in terrestrial cyroenvironments. Here we use the 16S rRNA gene as a marker for genetic diversity to compare two visually distinct but spatially integrated surface microbial mats on Axel Heiberg Island, Canadian high arctic, proximal to a perennial saline spring. This is the first study to describe the bacterial diversity in microbial mats on Axel Heiberg Island. The hypersaline springs on Axel Heiberg represent a unique analog to putative subsurface aquifers on Mars. The Martian subsurface represents the longest-lived potentially habitable environment on Mars and a better understanding of the microbial communities on Earth that thrive in analog conditions will help direct future life detection missions. The microbial mats sampled on Axel Heiberg are only visible during the summer months in seasonal flood plains formed by melt water and run-off from the proximal spring. Targeted-amplicon sequencing revealed that not only does the bacterial composition of the two mat communities differ substantially from the sediment community of the proximal cold spring, but that the mat communities are distinct from any other microbial community in proximity to the Arctic springs studied to date. All samples are dominated by Gammaproteobacteria: Thiotichales is dominant within the spring samples while Alteromonadales comprises a significant component of the mat communities. The two mat samples differ in their Thiotichales:Alteromonadales ratio and contribution of Bacteroidetes to overall diversity. The red mats have a greater proportion of Alteromonadales and Bacteroidetes reads. The distinct bacterial composition of the mat bacterial communities suggests that the spring communities are not sourced from the surface, and that seasonal melt events create

Springs as hydrologic refugia in a changing climate? A remote sensing approach

Science.gov (United States)

Cartwright, Jennifer M.; Johnson, Henry M.

2018-01-01

Spring‐fed wetlands are ecologically important habitats in arid and semi‐arid regions. Springs have been suggested as possible hydrologic refugia from droughts and climate change; however, springs that depend on recent precipitation or snowmelt for recharge may be vulnerable to warming and drought intensification. Springs that are expected to maintain their ecohydrologic function in a warmer, drier climate may be priorities for conservation and restoration. Identifying such springs is difficult because many springs lack hydrologic records of adequate temporal extent and resolution to assess their resilience to water cycle changes. This study demonstrates proof‐of‐concept for the assessment of certain spring types (i.e., helocrene, hypocrene, and hillslope springs) in terms of hydrologic and ecological resilience to climatic water stress using freely available remote‐sensing and climate data. We used the Normalized Difference Vegetation Index (NDVI) from 1985 through 2011 to delineate surface‐moisture zones (SMZs) associated with 39 clusters of 172 springs in a montane sage‐steppe landscape in southeastern Oregon, USA. We developed and synthesized seven NDVI‐based indicators of SMZ resilience to interannual changes in water availability: (1) mean and (2) standard deviation of July NDVI; (3) mean difference in July NDVI and (4) difference in coefficient of variation for July NDVI between each SMZ and its surrounding watershed; (5) response of SMZ July NDVI to 90‐day antecedent precipitation; (6) response of SMZ July NDVI to the previous winter's snowpack; and (7) range of NDVI values from an exceptionally wet year followed by three dry years. Because all resilience indicators were highly inter‐correlated, we derived an overall metric of SMZ resilience using principal components analysis that accounted for 66% of total variance. This overall resilience score was positively correlated with SMZ elevation, slope, mean annual precipitation, and with

Weldon Spring, Missouri, Site Annual Report for Calendar Year 2015 June 2016

Energy Technology Data Exchange (ETDEWEB)

Starr, Ken [U.S. Dept. of Energy, Washington, DC (United States). Office of Legacy Management (LM); Deyo, Yvonne [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2016-06-01

1.1 Purpose and Scope. This report summarizes the activities, compliance status, annual inspection, and environmental monitoring results from calendar year 2015 for the Weldon Spring, Missouri, Site. The U.S. Department of Energy (DOE) prepares this annual report as part of the site’s long-term surveillance and maintenance (LTS&M) activities, in accordance with the requirements of the Long-Term Surveillance and Maintenance Plan for the Weldon Spring, Missouri, Site (LTS&M Plan) (DOE 2008a) and the Federal Facility Agreement for the Weldon Spring Site (DOE 2006). The Weldon Spring site is a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) site. 1.2 Site Description. The Weldon Spring site is located in St. Charles County, Missouri, about 30 miles west of St. Louis, Missouri (Figure 1). The site comprises two geographically distinct, DOE-owned properties: the former Weldon Spring Chemical Plant and Raffinate Pit sites (Chemical Plant) and the former Weldon Spring Quarry (Quarry). The former Chemical Plant is located about 2 miles southwest of the junction of Missouri State Route 94 and Interstate 64. The Quarry is about 4 miles southwest of the former Chemical Plant. Both sites are accessible from Missouri State Route 94. During the early 1940s, the Department of the Army acquired 17,232 acres of private land in St. Charles County for the construction of the Weldon Spring Ordnance Works facility. The former Ordnance Works site has since been divided into several contiguous areas under different ownership, as depicted in Figure 2. Current land use of the former Ordnance Works site includes the former Chemical Plant and Quarry, the U.S. Army Reserve Weldon Spring Training Area, the Missouri Department of Conservation (MDC), the Missouri Department of Natural Resources (MDNR) Division of State Parks (MDNR-Parks), Francis Howell High School, a St. Charles County highway maintenance (formerly Missouri Department of Transportation [Mo

A semi-analytical study on helical springs made of shape memory polymer

International Nuclear Information System (INIS)

Baghani, M; Naghdabadi, R; Arghavani, J

2012-01-01

In this paper, the responses of shape memory polymer (SMP) helical springs under axial force are studied both analytically and numerically. In the analytical solution, we first derive the response of a cylindrical tube under torsional loadings. This solution can be used for helical springs in which both the curvature and pitch effects are negligible. This is the case for helical springs with large ratios of the mean coil radius to the cross sectional radius (spring index) and also small pitch angles. Making use of this solution simplifies the analysis of the helical springs to that of the torsion of a straight bar with circular cross section. The 3D phenomenological constitutive model recently proposed for SMPs is also reduced to the 1D shear case. Thus, an analytical solution for the torsional response of SMP tubes in a full cycle of stress-free strain recovery is derived. In addition, the curvature effect is added to the formulation and the SMP helical spring is analyzed using the exact solution presented for torsion of curved SMP tubes. In this modified solution, the effect of the direct shear force is also considered. In the numerical analysis, the 3D constitutive equations are implemented in a finite element program and a full cycle of stress-free strain recovery of an SMP (extension or compression) helical spring is simulated. Analytical and numerical results are compared and it is shown that the analytical solution gives accurate stress distributions in the cross section of the helical SMP spring besides the global load–deflection response. Some case studies are presented to show the validity of the presented analytical method. (paper)

Metagenomic Study of Iron Homeostasis in Iron Depositing Hot Spring Cyanobacterial Community

Science.gov (United States)

Brown, I.; Franklin H.; Tringe, S. G.; Klatt, C. G.; Bryant, D. A.; Sarkisova, S. A.; Guevara, M.

2010-01-01

Introduction: It is not clear how an iron-rich thermal hydrosphere could be hospitable to cyanobacteria, since reduced iron appears to stimulate oxidative stress in all domains of life and particularly in oxygenic phototrophs. Therefore, metagenomic study of cyanobacterial community in iron-depositing hot springs may help elucidate how oxygenic prokaryotes can withstand the extremely high concentrations of reactive oxygen species (ROS) produced by interaction between environmental Fe2+ and O2. Method: Anchor proteins from various species of cyanobacteria and some anoxygenic phototrophs were selected on the basis of their hypothetical role in Fe homeostasis and the suppression of oxidative stress and were BLASTed against the metagenomes of iron-depositing Chocolate Pots and freshwater Mushroom hot springs. Results: BLASTing proteins hypothesized to be involved in Fe homeostasis against the microbiomes from the two springs revealed that iron-depositing hot spring has a greater abundance of defensive proteins such as bacterioferritin comigratory protein (Bcp) and DNA-binding Ferritin like protein (Dps) than a fresh-water hot spring. One may speculate that the abundance of Bcp and Dps in an iron-depositing hot spring is connected to the need to suppress oxidative stress in bacteria inhabiting environments with high Fe2+ concnetration. In both springs, Bcp and Dps are concentrated within the cyanobacterial fractions of the microbial community (regardless of abundance). Fe3+ siderophore transport (from the transport system permease protein query) may be less essential to the microbial community of CP because of the high [Fe]. Conclusion: Further research is needed to confirm that these proteins are unique to photoautotrophs such as those living in iron-depositing hot spring.

SPRING BARLEY BREEDING FOR MALTING QUALITY

Directory of Open Access Journals (Sweden)

Alžbeta Žofajová

2010-05-01

Full Text Available The aim of this contribution is to illustrate the results of spring barley breeding for malting quality and point out an important position of variety in production of  qualitative  raw material for maltinq and beer  industry as well as the system of evaluation the qualitative parameters of breeding materials and adaptation of barley breeding programms to the  new requirements of  malting and beer industry. As an example of the results obtained most recently description is made of the Ezer, Levan, Donaris, Sladar spring barley varieties with very good malting quality and effective resistance to  powdery mildew.  Cultivation of these varieties  and malting barley production with  reduced use  of pesticidies is environmentally friedly alternative. doi:10.5219/50

Thermophoretic forces on DNA measured with a single-molecule spring balance

DEFF Research Database (Denmark)

Pedersen, Jonas Nyvold; Lüscher, Christopher James; Marie, Rodolphe

2014-01-01

We stretch a single DNA molecule with thermophoretic forces and measure these forces with a spring balance: the DNA molecule itself. It is an entropic spring which we calibrate, using as a benchmark its Brownian motion in the nanochannel that contains and prestretches it. This direct measurement ....... We find the Soret coefficient per unit length of DNA at various ionic strengths. It agrees, with novel precision, with results obtained in bulk for DNA too short to shield itself and with the thermodynamic model of thermophoresis.......We stretch a single DNA molecule with thermophoretic forces and measure these forces with a spring balance: the DNA molecule itself. It is an entropic spring which we calibrate, using as a benchmark its Brownian motion in the nanochannel that contains and prestretches it. This direct measurement...

Rapid River Hatchery - Spring Chinook, Final Report

International Nuclear Information System (INIS)

Watson, M.

1996-05-01

This report presents the findings of the independent audit of the Rapid River Hatchery (Spring Chinook). The hatchery is located in the lower Snake River basin near Riggins Idaho. The hatchery is used for adult collection, egg incubation, and rearing of spring chinook. The audit was conducted in April 1996 as part of a two-year effort that will include 67 hatcheries and satellite facilities located on the Columbia and Snake River system in Idaho, Oregon, and Washington. The hatchery operating agencies include the US Fish and Wildlife Service, Idaho Department of Fish and Game, Oregon Department of Fish and Wildlife, and Washington Department of Fish and Wildlife

Finite element fatigue analysis of rectangular clutch spring of automatic slack adjuster

Science.gov (United States)

Xu, Chen-jie; Luo, Zai; Hu, Xiao-feng; Jiang, Wen-song

2015-02-01

The failure of rectangular clutch spring of automatic slack adjuster directly affects the work of automatic slack adjuster. We establish the structural mechanics model of automatic slack adjuster rectangular clutch spring based on its working principle and mechanical structure. In addition, we upload such structural mechanics model to ANSYS Workbench FEA system to predict the fatigue life of rectangular clutch spring. FEA results show that the fatigue life of rectangular clutch spring is 2.0403×105 cycle under the effect of braking loads. In the meantime, fatigue tests of 20 automatic slack adjusters are carried out on the fatigue test bench to verify the conclusion of the structural mechanics model. The experimental results show that the mean fatigue life of rectangular clutch spring is 1.9101×105, which meets the results based on the finite element analysis using ANSYS Workbench FEA system.

Static deformation of a heavy spring due to gravity and centrifugal force

Energy Technology Data Exchange (ETDEWEB)

Essen, Hanno; Nordmark, Arne, E-mail: hanno@mech.kth.s [Department of Mechanics, KTH, SE-100 44 Stockholm (Sweden)

2010-05-15

The static equilibrium deformation of a heavy spring due to its own weight is calculated for two cases: first for a spring hanging in a constant gravitational field, and then for a spring which is at rest in a rotating system where it is stretched by the centrifugal force. Two different models are considered: first a discrete model assuming a finite number of point masses connected by springs of negligible weight, and then the continuum limit of this model. In the second case, the differential equation for the deformation is obtained by demanding that the potential energy is minimized. In this way a simple application of the variational calculus is obtained.

Modeling smog along the Los Angeles-Palm Springs trajectory

International Nuclear Information System (INIS)

Hanna, S.R.

1976-01-01

Observations of smog concentrations and wind patterns during the summer of 1973 in Los Angeles, Pomona, Riverside, Banning, and Palm Springs, California are presented which show that high oxidant concentrations at Banning and Palm Springs are often due to advection of smog from source regions in the more densely populated western part of the Los Angeles basin. At Pomona and Riverside, advection from upwind source regions combines with the effects of local emissions to cause long durations of high oxidant concentrations with peak times in the mid afternoon. An empirical model for the diurnal oxidant variation is suggested which satisfactorily simulates observed concentrations. More complex models which include chemical kinetics systems do not perform very satisfactorily at the rural stations of Banning and Palm Springs, especially at night when observed oxidant concentrations remain high

Do natural spring waters in Australia and New Zealand affect health? A systematic review.

Science.gov (United States)

Stanhope, Jessica; Weinstein, Philip; Cook, Angus

2018-02-01

Therapeutic use of spring waters has a recorded history dating back to at least 1550 BC and includes both bathing in and drinking such waters for their healing properties. In Australia and New Zealand the use of therapeutic spring waters is a much more recent phenomenon, becoming a source of health tourism from the late 1800s. We conducted a systematic review aimed at determining the potential health outcomes relating to exposure to Australian or New Zealand natural spring water. We found only low-level evidence of adverse health outcomes relating to this spring water exposure, including fatalities from hydrogen sulphide poisoning, drowning and primary amoebic meningoencephalitis. We found no studies that investigated the therapeutic use of these waters, compared with similar treatment with other types of water. From the broader literature, recommendations have been made, including fencing potentially harmful spring water, and having signage and media messages to highlight the potential harms from spring water exposure and how to mitigate the risks (e.g. not putting your head under water from geothermal springs). Sound research into the potential health benefits of Australian and New Zealand spring waters could provide an evidence base for the growing wellness tourism industry.

Magnetically Coupled Magnet-Spring Oscillators

Science.gov (United States)

Donoso, G.; Ladera, C. L.; Martin, P.

2010-01-01

A system of two magnets hung from two vertical springs and oscillating in the hollows of a pair of coils connected in series is a new, interesting and useful example of coupled oscillators. The electromagnetically coupled oscillations of these oscillators are experimentally and theoretically studied. Its coupling is electromagnetic instead of…

Wheat Quality Council, Hard Spring Wheat Technical Committee, 2017 Crop

Science.gov (United States)

Nine experimental lines of hard spring wheat were grown at up to six locations in 2017 and evaluated for kernel, milling, and bread baking quality against the check variety Glenn. Wheat samples were submitted through the Wheat Quality Council and processed and milled at the USDA-ARS Hard Red Spring...

Beneficial effect of hot spring bathing on stress levels in Japanese macaques.

Science.gov (United States)

Takeshita, Rafaela S C; Bercovitch, Fred B; Kinoshita, Kodzue; Huffman, Michael A

2018-05-01

The ability of animals to survive dramatic climates depends on their physiology, morphology and behaviour, but is often influenced by the configuration of their habitat. Along with autonomic responses, thermoregulatory behaviours, including postural adjustments, social aggregation, and use of trees for shelter, help individuals maintain homeostasis across climate variations. Japanese macaques (Macaca fuscata) are the world's most northerly species of nonhuman primates and have adapted to extremely cold environments. Given that thermoregulatory stress can increase glucocorticoid concentrations in primates, we hypothesized that by using an available hot spring, Japanese macaques could gain protection against weather-induced cold stress during winter. We studied 12 adult female Japanese macaques living in Jigokudani Monkey Park, Japan, during the spring birth season (April to June) and winter mating season (October to December). We collected faecal samples for determination of faecal glucocorticoid (fGC) metabolite concentrations by enzyme immunoassay, as well as behavioural data to determine time spent in the hot springs, dominance rank, aggression rates, and affiliative behaviours. We used nonparametric statistics to examine seasonal changes in hot spring bathing, and the relationship between rank and air temperature on hot spring bathing. We used general linear mixed-effect models to examine factors impacting hormone concentrations. We found that Japanese macaques use hot spring bathing for thermoregulation during the winter. In the studied troop, the single hot spring is a restricted resource favoured by dominant females. High social rank had both costs and benefits: dominant females sustained high fGC levels, which were associated with high aggression rates in winter, but benefited by priority of access to the hot spring, which was associated with low fGC concentrations and therefore might help reduce energy expenditure and subsequent body heat loss. This unique

Novel method for equivalent stiffness and Coulomb's damping ratio analyses of leaf spring

International Nuclear Information System (INIS)

Wen Jun, Wu; Yu, Xiang; Le Mei, Zhu; Li Jun, He

2012-01-01

The leaf spring is a representative type of laminated structure. Based on the linear theories of curve beams, the first derivatives of the leave's status vector of the leaf spring are provided. The first derivatives of the combination status-vector are obtained by properly dealing with the nonlinear interacted forces between adjacent leaves. Moreover, the precise integration technology and the transform matrix method are introduced to solve the equations. The force displacement curve of a leaf spring is then calculated separately by using the present method and the finite element software ANSYS. From the results, the precision and advantages of the present methods for analyzing the leaf spring are revealed. The Coulomb's damping ratio of the leaf spring is studied by using the present method

Migratory characteristics of spring chinook salmon in the Willamette River

International Nuclear Information System (INIS)

Snelling, J.C.; Schreck, C.B.; Bradford, C.S.; Davis, L.E.; Slater, C.H.; Beck, M.T.; Ewing, S.K.

1993-05-01

This report documents our research to examine in detail the migration of juvenile and adult spring chinook salmon in the Willamette River. We seek to determine characteristics of seaward migration of spring chinook smolts in relation to oxygen supplementation practices at Willamette Hatchery, and to identify potential sources of adult spring chinook mortality in the Willamette River above Willamette Falls and use this information towards analysis of the study on efficiency of oxygen supplementation. The majority of juvenile spring chinook salmon released from Willamette hatchery in 1991 begin downstream movement immediately upon liberation. They travel at a rate of 1.25 to 3.5 miles per hour during the first 48 hours post-release. Considerably slower than the water velocities available to them. Juveniles feed actively during migration, primarily on aquatic insects. Na + /K + gill ATPase and cortisol are significantly reduced in juveniles reared in the third pass of the Michigan series with triple density and oxygen supplementation, suggesting that these fish were not as well developed as those reared under other treatments. Returning adult spring chinook salmon migrate upstream at an average rate of about 10 to 20 miles per day, but there is considerable between fish variation. Returning adults exhibit a high incidence of wandering in and out of the Willamette River system above and below Willamette Falls

Geochemical characterization of groundwater discharging from springs north of the Grand Canyon, Arizona, 2009–2016

Science.gov (United States)

Beisner, Kimberly R.; Tillman, Fred D.; Anderson, Jessica R.; Antweiler, Ronald C.; Bills, Donald J.

2017-08-01

A geochemical study was conducted on 37 springs discharging from the Toroweap Formation, Coconino Sandstone, Hermit Formation, Supai Group, and Redwall Limestone north of the Grand Canyon near areas of breccia-pipe uranium mining. Baseline concentrations were established for the elements As, B, Li, Se, SiO2, Sr, Tl, U, and V. Three springs exceeded U.S. Environmental Protection Agency drinking water standards: Fence Spring for arsenic, Pigeon Spring for selenium and uranium, and Willow (Hack) Spring for selenium. The majority of the spring sites had uranium values of less than 10 micrograms per liter (μg/L), but six springs discharging from all of the geologic units studied that are located stratigraphically above the Redwall Limestone had uranium values greater than 10 μg/L (Cottonwood [Tuckup], Grama, Pigeon, Rock, and Willow [Hack and Snake Gulch] Springs). The geochemical characteristics of these six springs with elevated uranium include Ca-Mg-SO4 water type, circumneutral pH, high specific conductance, correlation and multivariate associations between U, Mo, Sr, Se, Li, and Zn, low 87Sr/86Sr, low 234U/238U activity ratios (1.34–2.31), detectable tritium, and carbon isotopic interpretation indicating they may be a mixture of modern and pre-modern waters. Similar geochemical compositions of spring waters having elevated uranium concentrations are observed at sites located both near and away from sites of uranium-mining activities in the present study. Therefore, mining does not appear to explain the presence of elevated uranium concentrations in groundwater at the six springs noted above. The elevated uranium at the six previously mentioned springs may be influenced by iron mineralization associated with mineralized breccia pipe deposits. Six springs discharging from the Coconino Sandstone (Upper Jumpup, Little, Horse, and Slide Springs) and Redwall Limestone (Kanab and Side Canyon Springs) contained water with corrected radiocarbon ages as much as 9

Hydrogeology and water chemistry of Infranz catchment springs, Bahir Dar Area, Lake Tana Basin, Ethiopia

Science.gov (United States)

Abera, F. N.

2017-12-01

The major springs in the Infranz catchment are a significant source of water for Bahir city and nearby villages, while they help to sustain Infranz River and the downstream wetlands. The aim of the research was to understand the hydrogeological conditions of these high-discharge springs, and to explain the hydrochemical composition of spring waters. Water samples from rainwater and springs were collected and analyzed and compared for major cations and anions. The hydrochemical data analysis showed that all water samples of the springs have freshwater chemistry, Ca-HCO3 type, while deep groundwater shows more evolved types. This indicates limited water-rock interaction and short residence time for the spring waters. The rise of NO3- and PO43- may indicate future water quality degradation unless the anthropogenic activities upgradient and nearby are restricted. The uptake of 75% of spring water for water supply of Bahir Dar results in wetland degradation. Key words: Spring water, Infranz River, Bahir Dar, Ethiopia, hydrochemistry

Springs-neaps cycles in daily total seabed light: Daylength-induced changes

Science.gov (United States)

Roberts, E. M.; Bowers, D. G.; Davies, A. J.

2014-04-01

In shallow, tidal seas, daily total seabed light is determined largely by the interaction of the solar elevation cycle, the tidal cycle in water depth, and any temporal variability in turbidity. Since tidal range, times of low water, and often turbidity vary in regular ways over the springs-neaps cycle, daily total seabed light exhibits cycles of the same periodicity. Corresponding cycles are likely to be induced in the daily total primary production of benthic algae and plants, particularly those light-limited specimens occupying the lower reaches of a sub-tidal population. Consequently, this effect is an important control on the growth patterns, depth distribution and survival of, for example, macroalgal forests and seagrass meadows. Seasonal changes in daylength exert an important additional control on these cycles, as they alter the fraction of the tidal and turbidity cycles occurring within daylight hours. Bowers et al. (1997) modelled this phenomenon numerically and predicted that for a site with low water at about midday and midnight at neaps tides, 6 am and 6 pm at springs, daily total seabed light peaks at neaps in winter, but the ‘sense' of the cycle ‘switches' so that it peaks at springs in summer - the longer daylength permits the morning and evening low water springs to contribute substantially to the daily total. Observations for such a site in North Wales (UK), presented in this paper, show that no such ‘switch' occurs, and neaps tides host the largest daily totals throughout the year. The predicted ‘switch' is not observed because turbidity increases generally at spring tides, and specifically at low water springs, both of which were not accounted for in the model. Observations at a second site in Brittany (France), diametrically opposite in terms of the times of low water at neaps and at springs, indicate a peak at springs throughout the year. Analytical tools are developed to calculate the percentage of daily total sea surface irradiance

School of Culinary Arts & Food Technology - Spring Newsletter 2017

OpenAIRE

Murphy, James Peter

2017-01-01

The School of Culinary Arts and Food Technology, Spring Newsletter captured the many events, research, awards, significant contributions and special civic and community activities which the students and staff members of the school have successfully completed leading up to the Spring period of 2017. The successful completion of these activities would not be possible without the active and on-going support of the 'INSPIRED' friends of Culinary Arts (sponsors).

Extension of elastic stiffness formula for leaf type holddown spring assembly

Energy Technology Data Exchange (ETDEWEB)

Song, Kee Nam; Kang, Heung Seok; Yoon, Kyung Ho; Kim, Hyung Kyu [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-09-01

Based on the Euler beam theory and the strain energy method, an elastic stiffness formula of the holddown spring assembly consisting of several leaves was previously derived. The formula was known to be useful to estimate the elastic stiffness of the holddown spring assembly only with the geometric data and the material properties of the leaf. Recently, it was reported that the elastic stiffness from the formula deviated much from the test results as the number of leaves was increased. In this study, in order to resolve such an increasing deviation as the increasing number of leaves, the formula has been extended to be able to consider normal forces and friction forces acting on interfaces between the leaves. The elastic stiffness analysis on specimens of leaf type holddown springs has been carried out using the extended formula and the analysis results are compared with the test results. As a result of comparisons, it is found that the extended formula is able to evaluate the elastic stiffness of the holddown spring assembly within an error range of 10%, irrespective of the number of leaves. In addition, it is found that the effect of shear forces and axial forces on the elastic stiffness of the holddown spring assembly is only below 0.2% of the elastic stiffness, and therefore the greatest portion of the elastic stiffness of the holddown spring assembly is attributed to the bending moment. (author). 13 refs., 10 figs., 12 tabs.

A high-force controllable MR fluid damper–liquid spring suspension system

International Nuclear Information System (INIS)

Raja, Pramod; Wang, Xiaojie; Gordaninejad, Faramarz

2014-01-01

The goal of the present research is to investigate the feasibility of incorporating a liquid spring in a semi-active suspension system for use in heavy off-road vehicles. A compact compressible magneto-rheological (MR) fluid damper–liquid spring (CMRFD–LS) with high spring rate is designed, developed and tested. Compressible MR fluids with liquid spring and variable damping characteristics are used. These fluids can offer unique functions in reducing the volume/weight of vehicle struts and improving vehicle dynamic stability and safety. The proposed device consists of a cylinder and piston–rod arrangement with an internal annular MR fluid valve. The internal pressures in the chambers on either side of the piston develop the spring force, while the pressure difference across the MR valve produces the damping force, when the fluid flows through the MR valve. Harmonic characterization of the CMRFD–LS is performed and the force–displacement results are presented. A fluid-mechanics based model is also developed to predict the performance of the system at different operating conditions and compared to the experimental results. Good agreement between the experimental results and theoretical predictions has been achieved. (paper)

MEMS mass-spring-damper systems using an out-of-plane suspension scheme

KAUST Repository

Abdel Aziz, Ahmed Kamal Said; Sharaf, Abdel Hameed; Serry, Mohamed Yousef; Sedky, Sherif Salah

2014-01-01

MEMS mass-spring-damper systems (including MEMS gyroscopes and accelerometers) using an out-of-plane (or vertical) suspension scheme, wherein the suspensions are normal to the proof mass, are disclosed. Such out-of-plane suspension scheme helps such MEMS mass-spring-damper systems achieve inertial grade performance. Methods of fabricating out-of-plane suspensions in MEMS mass-spring-damper systems (including MEMS gyroscopes and accelerometers) are also disclosed.

MEMS mass-spring-damper systems using an out-of-plane suspension scheme

KAUST Repository

Abdel Aziz, Ahmed Kamal Said

2014-02-04

MEMS mass-spring-damper systems (including MEMS gyroscopes and accelerometers) using an out-of-plane (or vertical) suspension scheme, wherein the suspensions are normal to the proof mass, are disclosed. Such out-of-plane suspension scheme helps such MEMS mass-spring-damper systems achieve inertial grade performance. Methods of fabricating out-of-plane suspensions in MEMS mass-spring-damper systems (including MEMS gyroscopes and accelerometers) are also disclosed.

A large-stroke shape memory alloy spring actuator using double-coil configuration

International Nuclear Information System (INIS)

Kim, Seung-Won; An, Sungmin; Cho, Kyu-Jin; Lee, Jong-Gu; Cho, Maenghyo

2015-01-01

One way to increase the range of motion of shape memory alloy (SMA) actuators is to create displacements of the SMA associated with not only the deformation from straining but also rigid-body motion from translation and rotation. Rigid-body motion allows the SMA to create larger displacements without exceeding the maximum recovery strain so that the SMA actuators can have a larger shape recovery ratio. To improve the linear actuation stroke of SMA wire actuators, a novel SMA spring actuator is proposed that employs a double-coil geometry that allows the displacement of the SMA to be mainly induced by rigid-body motion. A double-coil SMA spring actuator is fabricated by coiling an SMA wire twice so that the double coiling results in a reduction of the initial length of the double-coil SMA spring actuator. The effects of the geometric parameters on the actuation characteristic of a double-coil SMA spring actuator are verified numerically by finite element analysis and experimentally according to a parametric study of the geometric parameters. The displacement-to-force profile of the double-coil SMA spring actuator is nonlinear, and the spring stiffness changes when the actuator transforms its configuration from a double-coil shape to a single-coil shape. According to the results of the parametric study, increasing the wire diameter increases both primary and secondary coil stiffness, and increasing the primary inner coil diameter decreases both primary and secondary coil stiffness, whereas increasing the secondary inner coil diameter decreases only the secondary coil stiffness. The result shows that one of the double-coil SMA spring actuators with an initial length of 8 mm has a recovery ratio of 1250%, while the recovery ratio of the single-coil SMA spring actuator with the same geometric parameters is 432%. (paper)

Rise and fall of road salt contamination of water-supply springs

Science.gov (United States)

Werner, Eberhard; Dipretoro, Richard S.

2006-12-01

A storage pile of de-icing agent consisting principally of sodium chloride was placed in the recharge area of two springs, and remained there for 2 years. Water flow is through fractures in rocks with low matrix permeability, along a hydraulic gradient developed along fracture zones. Salt contamination in the springs was noticed about 1 year after the salt was placed. When the salt was removed 1 year later, chloride concentrations in the springs exceeded 500 mg/L. Monitoring for the following 5 years showed salt contamination rising for the first year, but receding to normal background after 5 years. Chloride to sodium ratios of the spring waters indicated that some sodium was initially sequestered, probably by ion exchange on clay minerals, in the early part of the monitoring period, and released during the latter part; thereby extending the period of contamination.

Fiscal 1999 survey on conservation of Jozankei hot spring. Survey report of hot spring alteration; 1999 nendo jozankei onsen hozen chosa. Onsen hendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-01

As a part of fiscal 1999 survey on conservation of Jozankei hot spring, a survey was made on the change of water composition in hot springs and rivers for the purpose of elucidating the cause of hot spring alteration. In the survey, sampling and water quality analysis were conducted once a month at four sources and one river point on the upstream side of Tsukimibashi bridge on the Toyohira river and at two sources and one river point between Tsukimibashi bridge and Takayamabashi bridge. Also carried out were sampling and constituent analysis at five points for river water of a wide area. The survey results were as follows. The pattern of change in spring water temperature was recognized such that it tended to rise in summer when river temperature was high and to fall in winter. Spring water temperature rose greatly at the time of higher water level like the thaw in some sources but conversely fell in other sources. The fluctuation trend in PH values was such that they mostly went up in April of snow melting time and in early August of much rain and went down in winter of little rain and less snowmelt. As for electric conductivity and dissolved constituents, it was recognized that the conductivity lowered and that the constituents decreased in concentration, all concurrently at the time of snowmelt and much rain. (NEDO)

Grid with hold-down springs for fuel assembly

International Nuclear Information System (INIS)

Petit, B.

1990-01-01

The grid, especially for use in a light water nuclear power plant, has many plates which are interlaced to form rod retaining cells and springs made by a U strip with two active legs opposite to the plates to exert a pressure on the rods. The springs have their two sections joined together by welding through an aperture in the plate. Below the welded joint the sections of the strip are curved outwards while their free ends are joined together by having them overlapping or crossing close to their tips [fr

Non-integrability of the generalized spring-pendulum problem

International Nuclear Information System (INIS)

Maciejewski, Andrzej J; Przybylska, Maria; Weil, Jacques-Arthur

2004-01-01

We investigate a generalization of the three-dimensional spring-pendulum system. The problem depends on two real parameters (k, a), where k is the Young modulus of the spring and a describes the nonlinearity of elastic forces. We show that this system is not integrable when k ≠ -a. We carefully investigated the case k = -a when the necessary condition for integrability given by the Morales-Ruiz-Ramis theory is satisfied. We discuss an application of the higher order variational equations for proving the non-integrability in this case

Explicit nonlinear finite element geometric analysis of parabolic leaf springs under various loads.

Science.gov (United States)

Kong, Y S; Omar, M Z; Chua, L B; Abdullah, S

2013-01-01

This study describes the effects of bounce, brake, and roll behavior of a bus toward its leaf spring suspension systems. Parabolic leaf springs are designed based on vertical deflection and stress; however, loads are practically derived from various modes especially under harsh road drives or emergency braking. Parabolic leaf springs must sustain these loads without failing to ensure bus and passenger safety. In this study, the explicit nonlinear dynamic finite element (FE) method is implemented because of the complexity of experimental testing A series of load cases; namely, vertical push, wind-up, and suspension roll are introduced for the simulations. The vertical stiffness of the parabolic leaf springs is related to the vehicle load-carrying capability, whereas the wind-up stiffness is associated with vehicle braking. The roll stiffness of the parabolic leaf springs is correlated with the vehicle roll stability. To obtain a better bus performance, two new parabolic leaf spring designs are proposed and simulated. The stress level during the loadings is observed and compared with its design limit. Results indicate that the newly designed high vertical stiffness parabolic spring provides the bus a greater roll stability and a lower stress value compared with the original design. Bus safety and stability is promoted, as well as the load carrying capability.

Explicit Nonlinear Finite Element Geometric Analysis of Parabolic Leaf Springs under Various Loads

Directory of Open Access Journals (Sweden)

Y. S. Kong

2013-01-01

Full Text Available This study describes the effects of bounce, brake, and roll behavior of a bus toward its leaf spring suspension systems. Parabolic leaf springs are designed based on vertical deflection and stress; however, loads are practically derived from various modes especially under harsh road drives or emergency braking. Parabolic leaf springs must sustain these loads without failing to ensure bus and passenger safety. In this study, the explicit nonlinear dynamic finite element (FE method is implemented because of the complexity of experimental testing A series of load cases; namely, vertical push, wind-up, and suspension roll are introduced for the simulations. The vertical stiffness of the parabolic leaf springs is related to the vehicle load-carrying capability, whereas the wind-up stiffness is associated with vehicle braking. The roll stiffness of the parabolic leaf springs is correlated with the vehicle roll stability. To obtain a better bus performance, two new parabolic leaf spring designs are proposed and simulated. The stress level during the loadings is observed and compared with its design limit. Results indicate that the newly designed high vertical stiffness parabolic spring provides the bus a greater roll stability and a lower stress value compared with the original design. Bus safety and stability is promoted, as well as the load carrying capability.

The effect of linear spring number at side load of McPherson suspension in electric city car

Science.gov (United States)

Budi, Sigit Setijo; Suprihadi, Agus; Makhrojan, Agus; Ismail, Rifky; Jamari, J.

2017-01-01

The function of the spring suspension on Mc Pherson type is to control vehicle stability and increase ride convenience although having tendencies of side load presence. The purpose of this study is to obtain simulation results of Mc Pherson suspension spring in the electric city car by using the finite element method and determining the side load that appears on the spring suspension. This research is conducted in several stages; they are linear spring designing models with various spring coil and spring suspension modeling using FEM software. Suspension spring is compressed in the vertical direction (z-axis) and at the upper part of the suspension springs will be seen the force that arises towards the x, y, and z-axis to simulate the side load arising on the upper part of the spring. The results of FEM simulation that the side load on the spring toward the x and y-axis which the value gets close to zero is the most stable spring.

N Springs expedited response action proposal

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

Since signing the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) in 1989, the parties to the agreement have recognized the need to modify the approach to conducting investigations, studies, and cleanup actions at Hanford. To implement this approach, the parties have jointly developed the Hanford Past-Practice Strategy. The strategy defines a non-time-critical expedited response action (ERA) as a response action ``needed to abate a threat to human health or welfare or the environment where sufficient time exists for formal planning prior to initiation of response. In accordance with the past-practice strategy, DOE proposes to conduct an ERA at the N Springs, located in the Hanford 100 N Area, to substantially reduce the strontium-90 transport into the river through the groundwater pathway. The purpose of this ERA proposal is to provide sufficient information to select a preferred alternative at N Springs. The nature of an ERA requires that alternatives developed for the ERA be field ready; therefore, all the technologies proposed for the ERA should be capable of addressing the circumstances at N Springs. A comparison of these alternatives is made based on protectiveness, cost, technical feasibility, and institutional considerations to arrive at a preferred alternative. Following the selection of an alternative, a design phase will be conducted; the design phase will include a detailed look at design parameters, performance specifications, and costs of the selected alternative. Testing will be conducted as required to generate design data.

Equivalent Air Spring Suspension Model for Quarter-Passive Model of Passenger Vehicles.

Science.gov (United States)

Abid, Haider J; Chen, Jie; Nassar, Ameen A

2015-01-01

This paper investigates the GENSIS air spring suspension system equivalence to a passive suspension system. The SIMULINK simulation together with the OptiY optimization is used to obtain the air spring suspension model equivalent to passive suspension system, where the car body response difference from both systems with the same road profile inputs is used as the objective function for optimization (OptiY program). The parameters of air spring system such as initial pressure, volume of bag, length of surge pipe, diameter of surge pipe, and volume of reservoir are obtained from optimization. The simulation results show that the air spring suspension equivalent system can produce responses very close to the passive suspension system.

The effect of support springs in ends welded gap hollow YT-joint

Directory of Open Access Journals (Sweden)

R. F. Vieira

Full Text Available This paper presents an analysis on the effect of support springs in an ends circular hollow sections welded into a YT joint. The overall behavior and failure of the joint were characterized under axial compression of the lap brace. Two joint failure modes were identified: chord wall plastification (Mode A and cross-sectional chord buckling (Mode F in the region below the lap brace. The system was modeled with and without support springs using the numerical finite element program Ansys. Model results were compared with experimental data in terms of principal stress in the joint intersection. The finite element model without support springs proved to be more accurate than that with support springs.

Natural and artificial radioactivity in Emendere thermal spring area in Western Anatolia

International Nuclear Information System (INIS)

Topcuoglu, S.; Karahan, G.; Guengoer, N.; Kirbasoglu, C.

2003-01-01

The distribution of the naturally occurring radionuclides 238 U, 232 Th, 226 Ra, 40 K and 210 Po and an anthropogenic radionuclide 137 Cs in foodstuff, indicator organism sediment and soil samples in Emendere thermal spring area in western Anatolia were studied by alpha- and gamma-spectrometry. At the same time, the gross-α and β concentrations are also determined in the mentioned samples and the thermal spring and other water samples. The results obtained showed that Emendere thermal spring and Emendere stream waters are unsuitable for consumption as drinking purpose. On the other hand, the people who live around the thermal spring area face no risk with consumption of the foodstuffs. (author)

Weldon Spring Site Environmental Report for calendar year 1994

International Nuclear Information System (INIS)

1995-05-01

This report for Calendar Year 1994 has been prepared to provide information about the public safety and environmental protection programs conducted by the Weldon Spring Site Remedial Action Project (WSSRAP). The Weldon Spring site is located in southern St. Charles County, Missouri, approximately 48 km (30 mi) west of St. Louis. The site consists of two main areas, the Weldon Spring Chemical Plant and raffinate pits and the Weldon Spring Quarry. The chemical plant, raffinate pits, and quarry are located on Missouri State Route 94, southwest of US Route 40/61. The objectives of the Site Environmental Report are to present a summary of data from the environmental monitoring program, to characterize trends and environmental conditions at the site, and to confirm compliance with environmental and health protection standards and requirements. The report also presents the status of remedial activities and the results of monitoring these activities to assess their impacts on the public and environment. This report includes monitoring data from routine radiological and nonradiological sampling activities. These data include estimates of dose to the public from the Weldon Spring site, estimates of effluent releases, and trends in groundwater contaminant levels. Additionally, applicable compliance requirements, quality assurance programs, and special studies conducted in 1994 to support environmental protection programs are discussed. Dose estimates presented in this report are based on hypothetical exposure scenarios of public use of areas near the site. In addition, release estimates have been calculated on the basis of 1994 National Pollutant Discharge Elimination System (NPDES) and air monitoring data. Effluent discharges from the site under routine NPDES and National Emission Standards for Hazardous Air Pollutants (NESHAPS) monitoring were below permitted levels

Modelling Flat Spring performance using FEA

International Nuclear Information System (INIS)

Fatola, B O; Keogh, P; Hicks, B

2009-01-01

This paper reports how the stiffness of a Flat Spring can be predicted using nonlinear Finite Element Analysis (FEA). The analysis of a Flat Spring is a nonlinear problem involving contact mechanics, geometric nonlinearity and material property nonlinearity. Research has been focused on improving the accuracy of the model by identifying and exploring the significant assumptions contributing to errors. This paper presents results from some of the models developed using FEA software. The validation process is shown to identify where improvements can be made to the model assumptions to increase the accuracy of prediction. The goal is to achieve an accuracy level of ±10 % as the intention is to replace practical testing with FEA modelling, thereby reducing the product development time and cost. Results from the FEA models are compared with experimental results to validate the accuracy.

A spring-block analogy for the dynamics of stock indexes

Science.gov (United States)

Sándor, Bulcsú; Néda, Zoltán

2015-06-01

A spring-block chain placed on a running conveyor belt is considered for modeling stylized facts observed in the dynamics of stock indexes. Individual stocks are modeled by the blocks, while the stock-stock correlations are introduced via simple elastic forces acting in the springs. The dragging effect of the moving belt corresponds to the expected economic growth. The spring-block system produces collective behavior and avalanche like phenomena, similar to the ones observed in stock markets. An artificial index is defined for the spring-block chain, and its dynamics is compared with the one measured for the Dow Jones Industrial Average. For certain parameter regions the model reproduces qualitatively well the dynamics of the logarithmic index, the logarithmic returns, the distribution of the logarithmic returns, the avalanche-size distribution and the distribution of the investment horizons. A noticeable success of the model is that it is able to account for the gain-loss asymmetry observed in the inverse statistics. Our approach has mainly a pedagogical value, bridging between a complex socio-economic phenomena and a basic (mechanical) model in physics.

Ikaite precipitation by mixing of shoreline springs and lake water, Mono Lake, California, USA

Science.gov (United States)

Bischoff, James L.; Stine, Scott; Rosenbauer, Robert J.; Fitzpatrick, John A.; Stafford, Thomas W., Jr.

1993-08-01

Metastable ikaite (CaCO 3·6H 2O) forms abundantly during winter months along the south shoreline of Mono Lake where shoreline springs mix with lake water. Ikaite precipitates because of its decreased solubility at low temperature and because of orthophosphate-ion inhibition of calcite and aragonite. During the spring some of the ikaite is transformed to anhydrous CaCO 3 and is incorporated into tufa, but most is dispersed by wave action into the lake where it reacts to form gaylussite (Na 2Ca(CO 3) 2· 5H 2O). Spring waters have low pH values, are dominantly Ca-Na-HCO 3, have low radiocarbon activities, and are mixtures of deep-seated geothermal and cold groundwaters. Chemical modeling reveals that precipitation of CaCO 3 can occur over a broad range of mixtures of spring and lake water with a maximum production occurring at 96% spring water and 4% lake water. Under these conditions all the Ca and a significant fraction of the CO 3 of the precipitate is spring supplied. A radiocarbon age of 19,580 years obtained on a natural ikaite sample supports this conclusion. With the springs supplying a large and probably variable portion of the carbonate, and with apparent 14C age of the carbonate varying from spring to spring, tufa of similar actual antiquity may yield significantly different 14C dates, making tufa at this location unsuitable for absolute age dating by the radiocarbon method.

Corrosion failure analysis of hearing aid battery-spring contacts

DEFF Research Database (Denmark)

Gudla, Visweswara Chakravarthy; Ambat, Rajan

2017-01-01

the susceptibility of these systems to galvanic corrosion. In this study, traditional behind the ear (BTE) hearing aid systems, which failed during service were analysed. Failure analysis was performed on the dome type battery-spring contact systems. The morphology of the contact areas was observed using scanning......Reliability of low power electrical contacts such as those in hearing aid battery-spring systems is a very critical aspect for the overall performance of the device. These systems are exposed to certain harsh environments like high humidity and elevated temperatures, and often in combination...... electron microscopy, and the compositional analysis of the corrosion products and contaminants was performed using energy dispersive X-ray spectroscopy. Wear track morphology was observed on the contact points, and the top coating on the dome was worn out exposing the substrate spring material...

Evaluating Gridded Spring Indices Using the USA National Phenology Network's Observational Phenology Data

Science.gov (United States)

Crimmins, T. M.; Gerst, K.

2017-12-01

The USA National Phenology Network (USA-NPN; www.usanpn.org) produces and freely delivers daily and short-term forecast maps of spring onset dates at fine spatial scale for the conterminous United States and Alaska using the Spring Indices. These models, which represent the start of biological activity in the spring season, were developed using a long-term observational record of four species of lilacs and honeysuckles contributed by volunteer observers. Three of the four species continue to be tracked through the USA-NPN's phenology observation program, Nature's Notebook. The gridded Spring Index maps have utility for a wide range of natural resource planning and management applications, including scheduling invasive species and pest detection and control activities, anticipating allergy outbreaks and planning agricultural harvest dates. However, to date, there has not been a comprehensive assessment of how well the gridded Spring Index maps accurately reflect phenological activity in lilacs and honeysuckles or other species of plants. In this study, we used observational plant phenology data maintained by the USA-NPN to evaluate how well the gridded Spring Index maps match leaf and flowering onset dates in a) the lilac and honeysuckle species used to construct the models and b) in several species of deciduous trees. The Spring Index performed strongly at predicting the timing of leaf-out and flowering in lilacs and honeysuckles. The average error between predicted and observed date of onset ranged from 5.9 to 11.4 days. Flowering models performed slightly better than leaf-out models. The degree to which the Spring Indices predicted native deciduous tree leaf and flower phenology varied by year, species, and region. Generally, the models were better predictors of leaf and flowering onset dates in the Northeastern and Midwestern US. These results reveal when and where the Spring Indices are a meaningful proxy of phenological activity across the United States.

Monitoring and analysis of liquid storage in LNG tank based on different support springs

Science.gov (United States)

He, Hua; Sun, Jianping; Li, Ke; Wu, Zheng; Chen, Qidong; Chen, Guodong; Cao, Can

2018-04-01

With the rapid development of social modernization, LNG vehicles are springing up in daily life. However, it is difficult to monitor and judge the liquid storage tanks accurately and quickly. Based on this, this paper presents a new method of liquid storage monitoring, LNG tank on-line vibration monitoring system. By collecting the vibration frequency of LNG tank and tank liquid and supporting spring system, the liquid storage quality in the tank can be calculated. In this experiment, various vibration modes of the tank spring system are fully taken into account. The vibration effects of different types of support springs on the LNG tank system were investigated. The results show that the spring model has a great influence on the test results. This study provides a technical reference for the selection of suitable support springs for liquid storage monitoring.

Liquid-metal dip seal with pneumatic spring

International Nuclear Information System (INIS)

Poindexter, A.M.

1977-01-01

An improved liquid-metal dip seal for sealing the annulus between rotating plugs in the reactor vessel head of a liquid-metal fast-breeder nuclear reactor has two legs of differing widths communicating under a seal blade; the wide leg is also in communication with cover gas of the reactor and the narrow leg is also in communication with an isolated plug annulus above the seal. The annulus contains inert gas which acts as a pneumatic spring. Upon increasing cover gas pressure which depresses the level in the wide leg and greatly increases the level in the narrow leg, the pneumatic spring is compressed, and resists further level changes, thus preventing radioactive cover gas from bubbling through the seal

The influence of spring length on the physical parameters of simple harmonic motion

International Nuclear Information System (INIS)

Triana, C A; Fajardo, F

2012-01-01

The aim of this work is to analyse the influence of spring length on the simple harmonic motion of a spring-mass system. In particular, we study the effect of changing the spring length on the elastic constant k, the angular frequency ω and the damping factor γ of the oscillations. To characterize the behaviour of these variables we worked with a series of springs of seven different lengths, in which the elastic constant was found by means of the spring-elongation measurement and ω was obtained from the measurement of the oscillation period T of a suspended mass. The oscillatory movement was recorded using a force sensor and the γ value was determined by the fit of the envelope oscillations. Graphical analysis of the results shows that k, ω and γ decrease when the natural spring length increases. This experiment can be performed with equipment normally found in undergraduate physics laboratories. In addition, through graphical analysis students can deduce some relationships between variables that determine the simple harmonic motion behaviour. (paper)

Effects of Physiochemical Factors on Prokaryotic Biodiversity in Malaysian Circumneutral Hot Springs

Directory of Open Access Journals (Sweden)

Chia S. Chan

2017-07-01

Full Text Available Malaysia has a great number of hot springs, especially along the flank of the Banjaran Titiwangsa mountain range. Biological studies of the Malaysian hot springs are rare because of the lack of comprehensive information on their microbial communities. In this study, we report a cultivation-independent census to describe microbial communities in six hot springs. The Ulu Slim (US, Sungai Klah (SK, Dusun Tua (DT, Sungai Serai (SS, Semenyih (SE, and Ayer Hangat (AH hot springs exhibit circumneutral pH with temperatures ranging from 43°C to 90°C. Genomic DNA was extracted from environmental samples and the V3–V4 hypervariable regions of 16S rRNA genes were amplified, sequenced, and analyzed. High-throughput sequencing analysis showed that microbial richness was high in all samples as indicated by the detection of 6,334–26,244 operational taxonomy units. In total, 59, 61, 72, 73, 65, and 52 bacterial phyla were identified in the US, SK, DT, SS, SE, and AH hot springs, respectively. Generally, Firmicutes and Proteobacteria dominated the bacterial communities in all hot springs. Archaeal communities mainly consisted of Crenarchaeota, Euryarchaeota, and Parvarchaeota. In beta diversity analysis, the hot spring microbial memberships were clustered primarily on the basis of temperature and salinity. Canonical correlation analysis to assess the relationship between the microbial communities and physicochemical variables revealed that diversity patterns were best explained by a combination of physicochemical variables, rather than by individual abiotic variables such as temperature and salinity.

From Fall to Spring, or Spring to Fall? Seasonal Cholera Transmission Cycles and Implications for Climate Change

Science.gov (United States)

Akanda, A. S.; Jutla, A. S.; Huq, A.; Colwell, R.; Islam, S.; WE Reason

2010-12-01

Cholera remains a major public health threat in many developing countries around the world. The striking seasonality and the annual recurrence of this infectious disease in endemic areas continues to be of considerable interest to scientists and public health workers. Despite major advances in the ecological, and microbiological understanding of Vibrio cholerae, the causative agent, the role of underlying macro-scale hydroclimatic processes in propagating the disease in different seasons and years is not well understood. The incidence of cholera in the Bengal Delta region, the ‘native homeland’ of cholera, shows distinct biannual peaks in the southern floodplains, as opposed to single annual peaks in coastal areas and the northern parts of Bangladesh, as well as other cholera-endemic regions in the world. A coupled analysis of the regional hydroclimate and cholera incidence reveals a strong association of the spatio-temporal variability of incidence peaks with seasonal processes and extreme events. At a seasonal scale, the cycles indicate a spring-fall transmission pattern, contrary to the prevalent notion of a fall-spring transmission cycle. We show that the asymmetric seasonal hydroclimatology affects regional cholera dynamics by providing a coastal growth environment for bacteria in spring, while propagating transmission to fall by flooding. This seasonal interpretation of the progression of cholera has important implications, for formulating effective cholera intervention and mitigation efforts through improved water management and understanding the impacts of changing climate patterns on seasonal cholera transmission. (Water Environental Research Education Actionable Solutions Network)

Global occurrence of archaeal amoA genes in terrestrial hot springs.

Science.gov (United States)

Zhang, Chuanlun L; Ye, Qi; Huang, Zhiyong; Li, Wenjun; Chen, Jinquan; Song, Zhaoqi; Zhao, Weidong; Bagwell, Christopher; Inskeep, William P; Ross, Christian; Gao, Lei; Wiegel, Juergen; Romanek, Christopher S; Shock, Everett L; Hedlund, Brian P

2008-10-01

Despite the ubiquity of ammonium in geothermal environments and the thermodynamic favorability of aerobic ammonia oxidation, thermophilic ammonia-oxidizing microorganisms belonging to the crenarchaeota kingdom have only recently been described. In this study, we analyzed microbial mats and surface sediments from 21 hot spring samples (pH 3.4 to 9.0; temperature, 41 to 86 degrees C) from the United States, China, and Russia and obtained 846 putative archaeal ammonia monooxygenase large-subunit (amoA) gene and transcript sequences, representing a total of 41 amoA operational taxonomic units (OTUs) at 2% identity. The amoA gene sequences were highly diverse, yet they clustered within two major clades of archaeal amoA sequences known from water columns, sediments, and soils: clusters A and B. Eighty-four percent (711/846) of the sequences belonged to cluster A, which is typically found in water columns and sediments, whereas 16% (135/846) belonged to cluster B, which is typically found in soils and sediments. Although a few amoA OTUs were present in several geothermal regions, most were specific to a single region. In addition, cluster A amoA genes formed geographic groups, while cluster B sequences did not group geographically. With the exception of only one hot spring, principal-component analysis and UPGMA (unweighted-pair group method using average linkages) based on the UniFrac metric derived from cluster A grouped the springs by location, regardless of temperature or bulk water pH, suggesting that geography may play a role in structuring communities of putative ammonia-oxidizing archaea (AOA). The amoA genes were distinct from those of low-temperature environments; in particular, pair-wise comparisons between hot spring amoA genes and those from sympatric soils showed less than 85% sequence identity, underscoring the distinctness of hot spring archaeal communities from those of the surrounding soil system. Reverse transcription-PCR showed that amoA genes were

Biomineralization of radioactive sulfide minerals in strong acidic Tamagawa hot springs

International Nuclear Information System (INIS)

Tazaki, Kazue; Watanabe, Hiroaki

2004-01-01

Bioaccumulation of radioactive sulfide minerals by bacteria in strong acidic hot spring water was found at Tamagawa Hot Springs, Akita prefecture in Japan. The hot spring water produces Hokutolite of radioactive minerals high radium and radon. The β-ray measurements of sediments and biofilms indicate 1850-2420 and 5700 cpm, respectively, which are 50-100 times higher than that of the water and the air (50-90 cpm). The characteristics of hot spring water show pH (1.2), Eh (140 mV), EC (29 mS/cm), DO (0.8 mg/l), and water temperature (99.5degC), indicating extremely strong acidic and reducing conditions. The hot spring water contains mainly HCl associated with high concentrations of Ca 2+ , Al 3+ , Fe 2+ , HSO 4 - and SO 4 2- . SEM-EDX and TEM demonstrate some insight into how microorganisms affect the chemistry and microbiological characteristics of the strong acidic surroundings with high S, As, Ba, and Ca contents in biofilms. Especially SEM-EDX, ED-XRF, and STEM-EDX elemental content maps illustrate the distribution of sulfur-bearing compounds of barite (BaSO 4 ), gypsum (CaSO 4 ·2H 2 O), elemental sulfur (S) and orpiment(As 2 S 3 ) in the reddish orange biofilms. The presence of a hydrogen sulfide-rich (H 2 S) thermal spring and gypsum deposits suggest the volatilization of H 2 S from the spring water, oxidation of the H 2 S gas to sulfuric acid, and reaction of the sulfuric acid. TEM micrographs of bacteria in the biofilms reveal in detail the intimate connections between biological and mineralogical processes that the cells are entirely accumulated with spherical grains, 100∼200 nm in diameter. The relationship among sulfide minerals, such as barite, gypsum, sulfur, orpiment, and Hakutolite, associated with bacteria implies that heavy metals have been transported from strong acidic hot spring water to sediments through bacteria metabolism. It is possible that the capability of radioactive sulfide biofilms for heavy metal immobilization can be used to

Proceedings of the Korean Society for Nondestructive Testing Spring Meeting 1992

International Nuclear Information System (INIS)

1992-05-01

This proceedings contains articles of the Korean Society for Nondestructive Testing Spring Meeting, 1992. It was held on May. 20, 1992 in Seoul, Korea and subject of the Korean Society for Nondestructive Testing Spring Meeting 1992. There are main session and technical session.

Theoretical Predictions of Springing and Their Comparison with Full Scale Measurements

DEFF Research Database (Denmark)

Gu, X.; Storhaug, G.; Vidic-Perunovic, Jelena

2003-01-01

The present paper considers a large ocean going ship with significant springing responses, which have made a large contribution to the fatigue cracking for certain structural details. Four different theories for predicting ship responses and associated computer programs for predictions of springing...

Proceedings of the Korean Society for Nondestructive Testing Spring Meeting 1993

International Nuclear Information System (INIS)

1993-05-01

This proceedings contains articles of the Korean Society for Nondestructive Testing Spring Meeting, 1993. It was held on May. 24, 1993 in Seoul, Korea and subject of the Korean Society for Nondestructive Testing Spring Meeting 1993. There are main session and technical session.

Trial lectures for accelerator operators in SPring-8

International Nuclear Information System (INIS)

Ohshima, T.

2004-01-01

In case of the SPring-8, accelerator operators are working in three shifts of eight hours. They are making the scheduled beam injection to the storage ring, routine measurements of beam parameters such as the COD, the betatron tunes, the bunch current of stored beam and so on. They are keeping watch on operational state every time. In case of something wrong, they will take measures to meet the situation. Newcomer of operator works with an experienced one to learn sequence of the beam injection, how to operate Graphical User Interface and (GUI) so on. In addition, we organise preliminary lectures on accelerator for operators. Topics done in the lectures are RF system, vacuum system, magnet system, monitors, beam diagnostics, accelerator and beamline control system etc. The contents of the lecture can be seen through web browser again and again. It is useful for operators to understand the SPring-8 facility and details of their work because some of them are not familiar with the accelerator field before being an operator of SPring-8. (author)

Thermomechanical Analysis of Shape-Memory Composite Tape Spring

Science.gov (United States)

Yang, H.; Wang, L. Y.

2013-06-01

Intelligent materials and structures have been extensively applied for satellite designs in order to minimize the mass and reduce the cost in the launch of the spacecraft. Elastic memory composites (EMCs) have the ability of high-strain packaging and shape-memory effect, but increase the parts and total weight due to the additional heating system. Shape-memory sandwich structures Li and Wang (J. Intell. Mater. Syst. Struct. 22(14), 1605-1612, 2011) can overcome such disadvantage by using the metal skin acting as the heating element. However, the high strain in the micro-buckled metal skin decreases the deployment efficiency. This paper aims to present an insight into the folding and deployment behaviors of shape-memory composite (SMC) tape springs. A thermomechanical process was analyzed, including the packaging deformation at an elevated temperature, shape frozen at the low temperature and shape recovery after reheating. The result shows that SMC tape springs can significantly decrease the strain concentration in the metal skin, as well as exhibiting excellent shape frozen and recovery behaviors. Additionally, possible failure modes of SMC tape springs were also analyzed.

Biodiversity of the microbial mat of the Garga hot spring.

Science.gov (United States)

Rozanov, Alexey Sergeevich; Bryanskaya, Alla Victorovna; Ivanisenko, Timofey Vladimirovich; Malup, Tatyana Konstantinovna; Peltek, Sergey Evgenievich

2017-12-28

Microbial mats are a good model system for ecological and evolutionary analysis of microbial communities. There are more than 20 alkaline hot springs on the banks of the Barguzin river inflows. Water temperature reaches 75 °C and pH is usually 8.0-9.0. The formation of microbial mats is observed in all hot springs. Microbial communities of hot springs of the Baikal rift zone are poorly studied. Garga is the biggest hot spring in this area. In this study, we investigated bacterial and archaeal diversity of the Garga hot spring (Baikal rift zone, Russia) using 16S rRNA metagenomic sequencing. We studied two types of microbial communities: (i) small white biofilms on rocks in the points with the highest temperature (75 °C) and (ii) continuous thick phototrophic microbial mats observed at temperatures below 70 °C. Archaea (mainly Crenarchaeota; 19.8% of the total sequences) were detected only in the small biofilms. The high abundance of Archaea in the sample from hot springs of the Baikal rift zone supplemented our knowledge of the distribution of Archaea. Most archaeal sequences had low similarity to known Archaea. In the microbial mats, primary products were formed by cyanobacteria of the genus Leptolyngbya. Heterotrophic microorganisms were mostly represented by Actinobacteria and Proteobacteria in all studied samples of the microbial mats. Planctomycetes, Chloroflexi, and Chlorobi were abundant in the middle layer of the microbial mats, while heterotrophic microorganisms represented mostly by Firmicutes (Clostridia, strict anaerobes) dominated in the bottom part. Besides prokaryotes, we detect some species of Algae with help of detection their chloroplasts 16 s rRNA. High abundance of Archaea in samples from hot springs of the Baikal rift zone supplemented our knowledge of the distribution of Archaea. Most archaeal sequences had low similarity to known Archaea. Metagenomic analysis of microbial communities of the microbial mat of Garga hot spring showed that

Diversity and Distribution of Thermophilic Bacteria in Hot Springs of Pakistan.

Science.gov (United States)

Amin, Arshia; Ahmed, Iftikhar; Salam, Nimaichand; Kim, Byung-Yong; Singh, Dharmesh; Zhi, Xiao-Yang; Xiao, Min; Li, Wen-Jun

2017-07-01

Chilas and Hunza areas, located in the Main Mantle Thrust and Main Karakoram Thrust of the Himalayas, host a range of geochemically diverse hot springs. This Himalayan geothermal region encompassed hot springs ranging in temperature from 60 to 95 °C, in pH from 6.2 to 9.4, and in mineralogy from bicarbonates (Tato Field), sulfates (Tatta Pani) to mixed type (Murtazaabad). Microbial community structures in these geothermal springs remained largely unexplored to date. In this study, we report a comprehensive, culture-independent survey of microbial communities in nine samples from these geothermal fields by employing a bar-coded pyrosequencing technique. The bacterial phyla Proteobacteria and Chloroflexi were dominant in all samples from Tato Field, Tatta Pani, and Murtazaabad. The community structures however depended on temperature, pH, and physicochemical parameters of the geothermal sites. The Murtazaabad hot springs with relatively higher temperature (90-95 °C) favored the growth of phylum Thermotogae, whereas the Tatta Pani thermal spring site TP-H3-b (60 °C) favored the phylum Proteobacteria. At sites with low silica and high temperature, OTUs belonging to phylum Chloroflexi were dominant. Deep water areas of the Murtazaabad hot springs favored the sulfur-reducing bacteria. About 40% of the total OTUs obtained from these samples were unclassified or uncharacterized, suggesting the presence of many undiscovered and unexplored microbiota. This study has provided novel insights into the nature of ecological interactions among important taxa in these communities, which in turn will help in determining future study courses in these sites.

Executive summary: Weldon Spring Site Environmental Report for calendar year 1992

International Nuclear Information System (INIS)

1993-06-01

This report has been prepared to provide information about the public safety and environmental protection programs conducted by the Weldon Spring Site Remedial Action Project. The Weldon Spring site is located in southern St. Charles County, Missouri, approximately 48 km (30 mi) west of St. Louis. The site consists of two main areas, the Weldon Spring Chemical Plant and raffinate pits and the Weldon Spring Quarry. The objectives of the Site Environmental Report are to present a summary of data from the environmental monitoring program, to characterize trends and environmental conditions at the site, and to confirm compliance with environmental and health protection standards and requirements. The report also presents the status of remedial activities and the results of monitoring these activities to assess their impacts on the public and environment. The scope of the environmental monitoring program at the Weldon Spring site has changed since it was initiated. Previously, the program focused on investigations of the extent and level of contaminants in the groundwater, surface waters, buildings, and air at the site. In 1992, the level of remedial activities required monitoring for potential impacts of those activities, particularly on surface water runoff and airborne effluents. This report includes monitoring data from routine radiological and nonradiological sampling activities. These data include estimates of dose to the public from the Weldon Spring site; estimates of effluent releases; and trends in groundwater contaminant levels. Also, applicable compliance requirements, quality assurance programs, and special studies conducted in 1992 to support environmental protection programs are reviewed

Review of selected 100-N waste sites related to N-Springs remediation projects

International Nuclear Information System (INIS)

DeFord, D.H.; Carpenter, R.W.

1996-01-01

This document has been prepared in support of the environmental restoration program at the US Department of Energy's Hanford Site near Richland, Washington, by the Bechtel Hanford, Inc. Facility and Waste Site Research Office. It provides historical information that documents and characterizes selected waste sites that are related to the N-Springs remediation projects. The N-Springs are a series of small, inconspicuous groundwater seepage springs located along the Columbia River shoreline near the 100-N Reactor. The spring site is hydrologically down-gradient from several 100-N Area liquid waste sites that are believed to have been the source(s) of the effluents being discharged by the springs. This report documents and characterizes these waste sites, including the 116-N-1 Crib and Trench, 116-N-3 Crib and Trench, unplanned releases, septic tariks, and a backwash pond

Analysis of Spring Flow Change in the Jinan City under Influences of Recent Human Activities

Science.gov (United States)

Liu, Xiaomeng; Hu, Litang; Sun, Kangning

2018-06-01

Jinan city, the capital of Shandong Province in China, is famous for its beautiful springs. With the rapid development of the economy in recent years, water demand in Jinan city has been increasing rapidly. The over-exploitation of groundwater has caused a decline in groundwater level and, notably, dried up springs under extreme climate conditions. To keep the springs gushing perennially and sustainably use groundwater resources, the local government has implemented many measures to restore the water table, such as the Sponge City Construction Project in Jinan. Focusing on changes in spring flow and its impact factors in Jinan, this paper analyzes the changes in observed spring flow in the most recent 50 years and then discusses the causes of decreases in the spring flow with the consideration of climate and human activities. Spring flow in the study area was changed from the natural state to a period of multiwater source management. The artificial neural network (ANN) model was developed to demonstrate the relationship among spring flow, precipitation, and groundwater abstraction to predict the variations of spring flow under the conditions of climate change and human activities. The good agreement between the simulated and observed results indicates that both precipitation and exploitation are important influence factors. However the effective infiltration of precipitation into groundwater is the most influential factor. The results can provide guidance for groundwater resource protection in the Jinan spring catchment.

Characterising hydrological behaviour of springs draining different alpine formations

Science.gov (United States)

Volze, N.; Smoorenburg, M.; Kienzler, P.; Naef, F.; Rabenstein, L.; Kinzelbach, W.

2012-04-01

The project SACflood (Susceptibility of alpine catchment flood runoff to changes in meteorological boundary conditions) concentrates on alpine areas and wants to identify catchments that show a damped reaction to runoff but may react unexpectedly strong to increased precipitation as observed in 2005 in the Schächen. The catchment showed a delayed and damped behaviour for smaller precipitation events but reacted with strongly increased discharge when a threshold amount of rainfall was reached, causing a flood with high damages. This is attributed to the complex interaction of storage and drainage mechanisms that are not yet well enough understood. Typical alpine geomorphic formations are identified that are likely to be associated with large storages which could considerably delay runoff reaction but still contribute to flow within a timescale relevant for flood formation. From these geomorphic formations deep drainage is measured as outflow from several springs. In addition natural tracers are measured in the springs. On a steep hill slope, associated to one of the observed springs, ground water levels are observed. Geoelectric profiles were recorded to depict the structure of the underground. Discharge measurements from the springs show remarkable differences between the sites. After long dry periods certain springs do not react to rainfall immediately but need considerable amounts of rain to increase discharge. Even steep slopes as well as large talus areas can substantially delay runoff. Observations of the groundwater levels reveal an unexpected picture of the underground. The water table is not as often assumed above the bedrock but at a depth of several meters within the highly fractured bedrock material. This can result in a much higher storage capacity of such slopes despite the steepness of the surface. On the basis of the results from field work conceptual ideas are developed. The influence of parameters such as the depth of the unsaturated zone and the

Equivalent Air Spring Suspension Model for Quarter-Passive Model of Passenger Vehicles

OpenAIRE

Abid, Haider J.; Chen, Jie; Nassar, Ameen A.

2015-01-01

This paper investigates the GENSIS air spring suspension system equivalence to a passive suspension system. The SIMULINK simulation together with the OptiY optimization is used to obtain the air spring suspension model equivalent to passive suspension system, where the car body response difference from both systems with the same road profile inputs is used as the objective function for optimization (OptiY program). The parameters of air spring system such as initial pressure, volume of bag, l...

An environmental survey of Serpentine Hot Springs: Geology, hydrology, geochemistry, and microbiology

Science.gov (United States)

Nordstrom, D. Kirk; Hasselbach, Linda; Ingebritsen, Steven E.; Skorupa, Dana; McCleskey, R. Blaine; McDermott, Timothy R.

2015-01-01

Serpentine Hot Springs is the most visited site in the Bering Land Bridge National Preserve. The hot springs have traditionally been used by the Native people of the Seward Peninsula for religious, medicinal and spiritual purposes and continue to be used in many of the same ways by Native people today. The hot springs are also popular with non-Native users from Nome and other communities, recreational users and pilots from out of the area, and hunters and hikers.

Proceedings of the Korean Society for Nondestructive Testing Spring Meeting 2001

International Nuclear Information System (INIS)

2001-05-01

This proceedings contains articles of the Korean Society for Nondestructive Testing Spring Meeting, 2001. It was held on May. 11-12, 2001 in Seoul, Korea and subject of the Korean Society for Nondestructive Testing Spring Meeting 2001. This proceedings is comprised of 5 sessions.

Arab Spring - Concepts and Characteristics (Case of Egypt

Directory of Open Access Journals (Sweden)

Ayman Gad El Ashkar

2016-12-01

Full Text Available This study aims at sheding light on the revolutions of the Arab Spring, especially in the case of Egypt, where the conceptual side will be reviewed and to identify the most important features and highlights of this event. During the second decade of the twenty-first century, the Arab region has marked a flurry of unusual at the political level. This flurry has created a very important phenomenon not only for the Arab region, but also worldwide. This phenomenon is known as the Arab Spring, which came as a result of the ongoing suffering of the peoples of the region from injustice, oppression and inequality in all spheres of life. Thus, to achieve this purpose, revolutionary concepts and the theoretical concept of revolution will be analyzed and studied, a comparison between western concept and the Arab revolution, as well as concentration on a particular focus on the concept of Egyptian Spring and the most prominent features of it. Through this work will be provided insights on the reality of revolutionary concepts and specifically the depth of the dimensions, aspects and characteristics that belong to the concept of the Revolution of Arab Spring in general, and Egypt in particular. There is no doubt that the study of this event cannot be stopped to the limits or the time, and that this event is not just about Arab nations or peoples of the Middle East region, but it has to do will all the peoples of the world living under the pressure of the same reasons and conditions of these revolutions.

Argillization by descending acid at Steamboat Springs, Nevada

Science.gov (United States)

Schoen, Robert; White, Donald E.; Hemley, J.J.

1974-01-01

Steamboat Springs, Nevada, an area of present-day hot springs, clearly illustrates the genetic dependence of some kaolin deposits on hot-spring activity. Andesite, granodiorite and arkosic sediments are locally altered at the land surface to siliceous residues consisting of primary quartz and anatase, plus opal from primary silicates. These siliceous residues commonly exhibit the textural and structural features of their unaltered equivalents. Beneath the siliceous residues, kaolin and alunite replace primary silicates and fill open spaces, forming a blanketlike deposit. Beneath the kaolin-alunite zone, montmorillonite, commonly accompanied by pyrite, replaces the primary silicates. On the ground surface, the same alteration mineral zones can be traced outward from the siliceous residue; however, hematite rather than pyrite accompanies montmorillonite.Chemical analysis indicates that sulfuric acid is the active altering agent. The acid forms from hydrogen sulfide that exsolves from deep thermal water, rises above the water table and is oxidized by sulfur-oxidizing bacteria living near the ground surface. This acid dissolves in precipitation or condensed water vapor and percolates downward destroying most of the primary minerals producing a siliceous residue. Coincidence of the water table with the downward transition from siliceous residue to kaolin-alunite signifies decreasing hydrogen metasomatism because of dilution of descending acid by ground water.In hot-spring areas, beds of siliceous sinter deposited at the surface by hypogene thermal water look, superficially, like areas of surficial acid alteration. Features diagnostic of a surficial alteration are the relict rock structures of a siliceous residue and a kaolin-alunite zone immediately beneath.

Trends and natural variability of North American spring onset as evaluated by a new gridded dataset of spring indices

Science.gov (United States)

Ault, Toby R.; Schwartz, Mark D.; Zurita-Milla, Raul; Weltzin, Jake F.; Betancourt, Julio L.

2015-01-01

Climate change is expected to modify the timing of seasonal transitions this century, impacting wildlife migrations, ecosystem function, and agricultural activity. Tracking seasonal transitions in a consistent manner across space and through time requires indices that can be used for monitoring and managing biophysical and ecological systems during the coming decades. Here a new gridded dataset of spring indices is described and used to understand interannual, decadal, and secular trends across the coterminous United States. This dataset is derived from daily interpolated meteorological data, and the results are compared with historical station data to ensure the trends and variations are robust. Regional trends in the first leaf index range from 20.8 to 21.6 days decade21, while first bloom index trends are between20.4 and 21.2 for most regions. However, these trends are modulated by interannual to multidecadal variations, which are substantial throughout the regions considered here. These findings emphasize the important role large-scale climate modes of variability play in modulating spring onset on interannual to multidecadal time scales. Finally, there is some potential for successful subseasonal forecasts of spring onset, as indices from most regions are significantly correlated with antecedent large-scale modes of variability.

Spring-block Model for Barkhausen Noise

International Nuclear Information System (INIS)

Kovacs, K.; Brechet, Y.; Neda, Z.

2005-01-01

A simple mechanical spring-block model is used for studying Barkhausen noise (BN). The model incorporates the generally accepted physics of domain wall movement and pinning. Computer simulations on this model reproduces the main features of the hysteresis loop and Barkhausen jumps. The statistics of the obtained Barkhausen jumps follows several scaling laws, in qualitative agreement with experimental results. The model consists of a one-dimensional frictional spring-block system. The blocks model the Bloch-walls that separate inversely oriented magnetic domains, and springs correspond to the magnetized regions. Three types of realistic forces are modelled with this system: 1. the force resulting from the magnetic energy of the neighboring domains in external magnetic field (modelled by forces having alternating orientations and acting directly on the blocks); 2. the force resulting from the magnetic self-energy of each domain (modelled by the elastic forces of the springs); 3. the pinning forces acting on the domain walls (modelled by position dependent static friction acting on blocks). The dynamics of the system is governed by searching for equilibrium: one particular domain wall can jump to the next pinning center if the resultant of forces 1. and 2. is greater then the pinning force. The external magnetic field is successively increased (or decreased) and the system is relaxed to mechanical equilibrium. During the simulations we are monitoring the variation of the magnetization focusing on the shape of the hysteresis loop, power spectrum, jump size (avalanche size) distribution, signal duration distribution, signal area distribution. The simulated shape of the hysteresis loops fulfills all the requirements for real magnetization phenomena. The power spectrum indicates different behavior in the low (1/f noise) and high (white noise) frequency region. All the relevant distribution functions show scaling behavior over several decades of magnitude with a naturally

Spring viremia of carp

Science.gov (United States)

Ahne, W.; Bjorklund, H.V.; Essbauer, S.; Fijan, N.; Kurath, G.; Winton, J.R.

2002-01-01

pring viremia of carp (SVC) is an important disease affecting cyprinids, mainly common carp Cyprinus carpio. The disease is widespread in European carp culture, where it causes significant morbidity and mortality. Designated a notifiable disease by the Office International des Epizooties, SVC is caused by a rhabdovirus, spring viremia of carp virus (SVCV). Affected fish show destruction of tissues in the kidney, spleen and liver, leading to hemorrhage, loss of water-salt balance and impairment of immune response. High mortality occurs at water temperatures of 10 to 17°C, typically in spring. At higher temperatures, infected carp develop humoral antibodies that can neutralize the spread of virus and such carp are protected against re-infection by solid immunity. The virus is shed mostly with the feces and urine of clinically infected fish and by carriers. Waterborne transmission is believed to be the primary route of infection, but bloodsucking parasites like leeches and the carp louse may serve as mechanical vectors of SVCV. The genome of SVCV is composed of a single molecule of linear, negative-sense, single-stranded RNA containing 5 genes in the order 3¹-NPMGL-5¹ coding for the viral nucleoprotein, phosphoprotein, matrix protein, glycoprotein, and polymerase, respectively. Polyacrylamide gel electrophoresis of the viral proteins, and sequence homologies between the genes and gene junctions of SVCV and vesicular stomatitis viruses, have led to the placement of the virus as a tentative member of the genus Vesiculovirus in the family Rhabdoviridae. These methods also revealed that SVCV is not related to fish rhabdoviruses of the genus Novirhabdovirus. In vitro replication of SVCV takes place in the cytoplasm of cultured cells of fish, bird and mammalian origin at temperatures of 4 to 31°C, with an optimum of about 20°C. Spring viremia of carp can be diagnosed by clinical signs, isolation of virus in cell culture and molecular methods. Antibodies directed

Green Team Readies for Spring with Plant Swap | Poster

Science.gov (United States)

By Carolynne Keenan, Contributing Writer Those looking for a cost-effective way to spruce up their yards this spring can stop by the National Cancer Institute at Frederick Green Team’s booth during the Spring Research Festival (SRF) on May 7 and 8. Pick up a free plant, donate overgrown plants from your yard, or swap for a new plant. Everyone is invited to participate in the swap, whether you have plants to donate or not.

A variable stiffness joint with electrospun P(VDF-TrFE-CTFE) variable stiffness springs

NARCIS (Netherlands)

Carloni, Raffaella; Lapp, Valerie I.; Cremonese, Andrea; Belcari, Juri; Zucchelli, Andrea

This letter presents a novel rotational variable stiffness joint that relies on one motor and a set of variable stiffness springs. The variable stiffness springs are leaf springs with a layered design, i.e., an electro-active layer of electrospun aligned nanofibers of poly(vinylidene

Dynamic mesh optimization based on the spring analogy

Directory of Open Access Journals (Sweden)

Schmidt Jonas

2014-01-01

Full Text Available We present an implementation of the spring analogy for three dimensional meshes in OpenFOAM. All parameters of the spring system are treated as fields that can either be pre-defined by the user, or updated at each time step according to specified geometrical regions or diffusion equations. The purpose of the method is to provide a pre-processing tool for mesh optimization. We study three simple test cases, a deformed block, an airfoil and a hill, and we analyze the evolution of skewness, non-orthogonality and aspect ratio during the approach of dynamic equilibrium.

FINAL REPORT WIND POWER WARM SPRINGS RESERVATION TRIBAL LANDS DOE GRANT NUMBER DE-FG36-07GO17077 SUBMITTED BY WARM SPRINGS POWER & WATER ENTERPRISES A CORPORATE ENTITY OF THE CONFEDERATED TRIBES OF WARM SPRINGS WARM SPRINGS, OREGON

Energy Technology Data Exchange (ETDEWEB)

Jim Manion; Michael Lofting; Wil Sando; Emily Leslie; Randy Goff

2009-03-30

Wind Generation Feasibility Warm Springs Power and Water Enterprises (WSPWE) is a corporate entity owned by the Confederated Tribes of the Warm Springs Reservation, located in central Oregon. The organization is responsible for managing electrical power generation facilities on tribal lands and, as part of its charter, has the responsibility to evaluate and develop renewable energy resources for the Confederated Tribes of Warm Springs. WSPWE recently completed a multi-year-year wind resource assessment of tribal lands, beginning with the installation of wind monitoring towers on the Mutton Mountains site in 2003, and collection of on-site wind data is ongoing. The study identified the Mutton Mountain site on the northeastern edge of the reservation as a site with sufficient wind resources to support a commercial power project estimated to generate over 226,000 MWh per year. Initial estimates indicate that the first phase of the project would be approximately 79.5 MW of installed capacity. This Phase 2 study expands and builds on the previously conducted Phase 1 Wind Resource Assessment, dated June 30, 2007. In order to fully assess the economic benefits that may accrue to the Tribes through wind energy development at Mutton Mountain, a planning-level opinion of probable cost was performed to define the costs associated with key design and construction aspects of the proposed project. This report defines the Mutton Mountain project costs and economics in sufficient detail to allow the Tribes to either build the project themselves or contract with a developer under the most favorable terms possible for the Tribes.

Hydrogeochemical characteristics and sources of salinity of the springs near Wenquanzhen in the eastern Sichuan Basin, China

Science.gov (United States)

Guo, Juan; Zhou, Xun; Wang, Lidong; Zhang, Yuqi; Shen, Xiaowei; Zhou, Haiyan; Ye, Shen; Fang, Bin

2017-12-01

Natural springs have the potential to provide important information on hydrogeochemical processes within aquifers. This study used traditional and classic technical methods and procedures to determine the characteristics and evolution of springs to gain further knowledge on the differences between hot saline springs and cold fresh springs. In a short river segment near Wenquanzhen in the eastern Sichuan Basin, southwest China, several natural springs coexist with total dissolved solids (TDS) ranging from less than 1 to 15 g/L and temperatures from 15 to 40 °C. The springs emanate from the outcropping Lower and Middle Triassic carbonates in the river valley cutting the core of an anticline. The cold springs are of Cl·HCO3-Na·Ca and Cl·SO4-Na types, and the hot saline springs are mainly of Cl-Na type. The chemistry of the springs has undergone some changes with time. The stable hydrogen and oxygen isotopes indicate that the spring waters are of a meteoric origin. The salinity of the springs originates from dissolution of minerals, including halite, gypsum, calcite and dolomite. The evolution of the springs involves the following mechanisms: the groundwater receives recharge from infiltration of precipitation, then undergoes deep circulation in the core of the anticline (incongruent dissolution of the salt-bearing strata occurs), and emerges in the river valley in the form of hot springs with high TDS. Groundwater also undergoes shallow circulation in the northern and southern flanks of the anticline and appears in the river valley in the form of cold springs with low TDS.

Studying Hardness Meter Spring Strength to Understand Hardness Distribution on Body Surfaces.

Science.gov (United States)

Arima, Yoshitaka

2017-10-01

For developing a hardness multipoint measurement system for understanding hardness distribution on biological body surfaces, we investigated the spring strength of the contact portion main axis of a biological tissue hardness meter (product name: PEK). We measured the hardness of three-layered sheets of six types of gel sheets (90 mm × 60 mm × 6 mm) constituting the acupuncture practice pads, with PEK measurements of 1.96 N, 2.94 N, 3.92 N, 4.90 N, 5.88 N, 6.86 N, 7.84 N, 8.82 N, and 9.81 N of the main axis spring strength. We obtained measurements 10 times for the gel sheets and simultaneously measured the load using a digital scale. We measured the hardness distribution of induration embedded and breast cancer palpation models, with a main axis with 1.96 N, 4.90 N, and 9.81 N spring strengths, to create a two-dimensional Contour Fill Chart. Using 4.90 N spring strength, we could obtain measurement loads of ≤3.0 N, and the mean hardness was 5.14 mm. This was close to the median of the total measurement range 0.0-10.0 mm, making the measurement range the largest for this spring strength. We could image the induration of the induration-embedded model regardless of the spring strength. Overall, 4.90 N spring strength was best suited for imaging cancer in the breast cancer palpation model. Copyright © 2017. Published by Elsevier B.V.

Baseline risk evaluation for exposure to bulk wastes at the Weldon Spring Quarry, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Haroun, L.A.; Peterson, J.M.; MacDonell, M.M.; Hlohowskyj, I.

1990-01-01

The US Department of Energy (DOE), under its Surplus Facilities Management Program (SFMP), is responsible for cleanup activities at the Weldon Spring site, Weldon Spring, Missouri. The site consists of a raffinate pits and chemical plant area and a quarry. This baseline risk evaluation has been prepared to support a proposed response action for management of contaminated bulk wastes in the quarry. The quarry became chemically and radioactively contaminated as a result of various wastes that were disposed of there between 1942 and 1969. This risk evaluation assesses potential impacts on human health and the environment that may result from exposure to releases of contaminants from the quarry under current site conditions. Risk assessment is a key component of the remedial investigation/feasibility study (RI/FS) process, as identified in guidance from the US Environmental Protection Agency (EPA); this process addresses sites subject to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) of 1980, as amended by the Superfund Amendments and Reauthorization Act of 1986. Response actions at the Weldon Spring quarry are subject to CERCLA requirements because the quarry is listed on the EPA's National Priorities List. The DOE is also responsible for complying with the requirements of the National Environmental Policy Act (NEPA) of 1969, which requires federal agencies to consider the environmental consequences of a proposed action as part of the decision-making process for that action. Although this document has not been prepared to fulfill specific NEPA requirements, the analyses contained herein --- along with the analyses provided in the remedial investigation, feasibility study, and other supporting documents --- are intended to meet the environmental assessment requirements of NEPA

Community impacts of mid-May frost event during an anomalously warm spring

Science.gov (United States)

Hufkens, K.; Sonnentag, O.; Keenan, T. F.; Richardson, A. D.; Melaas, E. K.; Bailey, A.; O'Keefe, J.; Friedl, M. A.

2011-12-01

Global land and ocean surface temperatures of 2010 have gone on record as one of the warmest of the last 131 years. In the northeastern US extraordinarily warm spring temperatures were recorded, averaging +3 °C above the long term mean, causing very early leaf development. However, the entire northeastern US region was hit by a severe frost event. Leveraging the coincidence of an anomalously warm spring and a late spring frost event we assess species specific responses of these combined extremes for three northern hardwood species(sugar maple, American beech, yellow birch) across an elevational gradient. We integrated ground observations with satellite and near-surface remote sensing data to address the following questions: 1) How did different species respond to a gradient in altitude / freezing temperatures? 2) How does phenological strategy influence this response? 3) To what extent were regional effects measurable? 4) How did the late spring frost event alter the carbon balance of a northern hardwood forest? 5) Finally, what changes do we foresee in community ecology? Our results show an early onset for all species, triggered by the anomalously warm spring. However, the three species responded differently to a late spring frost event. Where both yellow birch and American beech remained largely unaffected by frost, by comparison, sugar maple showed severe frost damage with increasing altitude resulting in leaf loss and delayed canopy development. Conservative estimates of gross carbon exchange losses due to the frost event ranged from 63 g C m-2 to 156 g C m-2, or ~5% to ~13 % of the annual gross carbon exchange of a northern hardwood forest. Our results suggest that the additional pressure on forest succession at high altitude range margins due to late spring frost events may provide a competitive advantage for yellow birch and American beech, at the expense of sugar maple. Consequently, a late spring frost does not only affect the short term carbon balance

Multilevel analysis of elastic morphology: The mantis shrimp's spring.

Science.gov (United States)

Rosario, M V; Patek, S N

2015-09-01

Spring systems, whether natural or engineered, are composed of compliant and rigid regions. Biological springs are often similar to monolithic structures that distribute compliance and rigidity across the whole system. For example, to confer different amounts of compliance in distinct regions within a single structure, biological systems typically vary regional morphology through thickening or elongation. Here, we analyze the monolithic spring in mantis shrimp (Stomatopoda) raptorial appendages to rapidly acquire or process prey. We quantified the shape of cross-sections of the merus segment of the raptorial appendage. We also examined specific regions of the merus that are hypothesized to either store elastic energy or provide structural support to permit energy storage in other regions of the system. We found that while all mantis shrimp contain thicker ventral bars in distal cross-sections, differences in thickness are more pronounced in high-impact "smasher" mantis shrimp than in the slower-striking "spearer" mantis shrimp. We also found that spearer cross-sections are more circular while those of smashers are more eccentric with elongation along the dorso-ventral axis. The results suggest that the regional thickening of ventral bars provides structural support for resisting spring compression and also reduces flexural stiffness along the system's long axis. This multilevel morphological analysis offers a foundation for understanding the evolution and mechanics of monolithic systems in biology. © 2015 Wiley Periodicals, Inc.

Passive base isolation with superelastic nitinol SMA helical springs

International Nuclear Information System (INIS)

Huang, Bin; Zhang, Haiyang; Wang, Han; Song, Gangbing

2014-01-01

Seismic isolation of structures such as multi-story buildings, nuclear reactors, bridges, and liquid storage tanks should be designed to preserve structural integrity. By implementing seismic isolation technology, the deformation of superstructures can be dramatically reduced, consequently helping to protect their safety as well. In this paper, an innovative type of passive base isolation system, which is mainly composed of superelastic nitinol SMA helical springs, is developed. In order to verify the effectiveness of the proposed system, a two-story experimental steel frame model is constructed, and two superelastic SMA helical springs are thermo-mechanically built in the laboratory. To describe the nonlinear mechanical properties of the superelastic SMA helical springs under reciprocating load, a phenomenological model is presented in terms of a series of tensile tests. Afterwards, a numerical model of the two-story frame with the suggested isolation system is set up to simulate the response of the isolated frame subjected to an earthquake. Both the experimental and the numerical simulation results indicate that the proposed base isolation system can remarkably suppress structural vibrations and has improved isolation effects when compared with a steel spring isolation system. Due to the capabilities of energy dissipation as well as fully re-centering, it is very applicable to utilize the suggested isolation system in base isolated structures to resist earthquakes. (paper)

Spring unit especially intended for a nuclear reactor core

International Nuclear Information System (INIS)

Brown, S.J.; Gorholt, Wilhelm.

1977-01-01

This invention relates to a spring unit or a group of springs bearing up a sprung mass against an unsprung mass. For instance, a gas cooled high temperature nuclear reactor includes a core of relatively complex structure supported inside a casing or vessel forming a shielded cavity enclosing the reactor core. This core can be assembled from a large number of graphite blocks of different sizes and shapes joined together to form a column. The blocks of each column can be fixed together so as to form together a loose side support. Under the effect of thermal expansion and contraction, shrinkage resulting from irradiation, the effects of pressure and the contraction and creep of the reactor vessel, it is not possible to confine all the columns of the reactor core in a cylindrical rigid structure. Further, the working of the nuclear reactor requires that the reactivity monitoring components may be inserted at any time in the reactor core. A standard process consists in mounting this loosely assembled reactor core in a floating manner by keeping it away from the vessel enclosure around it by means of a number of springs fitted between the lateral surfaces of the core unit and the reactor vessel. The core may be considered as a spring supported mass whereas, relatively, the reactor vessel is a mass that is not flexibly supported [fr

A Belleville-spring-based electromagnetic energy harvester

International Nuclear Information System (INIS)

Castagnetti, Davide

2015-01-01

Energy harvesting from kinetic ambient energy is particularly effective to power autonomous sensors. This work proposes an innovative energy converter based on two counteracting Belleville springs and exploiting their peculiarity, for a height to thickness ratio equal to 1.414, of nearly zero stiffness over a wide deflection range. After analytical and numerical modelling a prototype is developed and experimentally investigated. The sub-optimal geometry of the commercial springs used in the prototype, together with a non-ideal response, makes the operating frequency for the prototype higher than in analytical and numerical predictions. Nevertheless, the harvester exhibits a significantly large bandwidth, together with a high output power, compared to similar solutions in the literature, for all the examined configurations and input excitations. (paper)

A study to evaluate therapeutic properties of minerals of manghopir hot spring, karachi

International Nuclear Information System (INIS)

Javed, A.; Iqbal, J.; Khan, F.A.; Siddiqui, I.

2009-01-01

European balneologists have extensively studied the therapeutic value of mineral water. Mineral springs with different mineral contents are recommended for various therapeutic uses. People have been using geothermal water for bathing and good health for many thousands of years A mineral hot spring has greater than 1000 mg/L (ppm) of naturally dissolved solids. Hot mineral spring water contains elements like calcium, magnesium, sodium, potassium as sulphates, bi- carbonates and chlorides, which are used externally to cure many diseases. Manghopir spring contain 38-84 mg/L calcium, 29-56 mg/L magnesium, 388-555 mg/L sodium, 411-599 mg/L chloride, 186-442 mg/L sulphate, 10-25 mg/L potassium, and 1509-2188 mg/L total dissolved solids while the pH was in the range of 7.2-7.8. The temperature of Manghopir Euthermal hot spring remains constant ranging between 40 to 47 degree C. (author)

Chemical composition of hot spring waters in the Oita river basins, Oita prefecture

Energy Technology Data Exchange (ETDEWEB)

Kawano, Tamio

1988-01-30

The source of the water from Oita River comes from the Kuju and Yubu-Tsurumi Volcanos, pouring into Beppu Bay. Its drainage area is 646 km/sup 2/ with a total length of 55 km. Hot springs are exist throughout most of the basin of the main and branches of Oita River. The chemical components of the hot springs in the Ota River basin -Yufuin, Yunotaira, Nagayu, Shonai/Hazama, and Oita City - have been analyzed. The equivalent of magnesium exceeds that of calcium in the carbonate springs of the above. Ca+Mg has positive correlations with HCO/sub 3/ in these carbonate springs. The water from these springs flows into the rivers and pours into Beppu Bay. The flow rate and chemical component concentration were measured at Fudai bridge. The concentration of chemical components having an average flow rate (30 ton/sec) were calculated. (4 figs, 7 tabs, 10 refs)

A study on the characteristics of the spacer spring by finite element method

Energy Technology Data Exchange (ETDEWEB)

Park, Sung Keun; Kim, Hyung Kyu; Kim, Kyu Tae [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-06-01

The mechanical integrity of spacer springs in KOFA was certified through the mechanical tests by KWU. In this report, the spacer spring characteristics were obtained by using a commercial FEM code ANSYS, and the calculated results were compared with the mechanical test results. It has been found that the analytical results from ANSYS were in good agreement with the test results in the actual working range of the spacer springs even though some errors occurred in the range of initial spring deflection. The errors were thought to occur due to the simplified boundary conditions and the nominal dimensions which are used in calculations rather than the as-fabricated dimensions. Though the results from ANSYS are not fully satisfied, the analytical method in this report has been verified to be used as a method for investigating the characteristic of spacer springs roughly before conducting mechanical tests. 8 tabs., 25 figs (Author) .new.

Amorphous calcium carbonate associated with biofilms in hot spring deposits

Science.gov (United States)

Jones, Brian; Peng, Xiaotong

2012-08-01

Calcium carbonate nanoparticles are intimately associated with crystalline calcite and aragonite in the Eryuan, Gongxiaoshe, and Zhuyuan hot springs (water temperature > 75 °C), which are located in Yunnan Province, China. The nanoparticles, springs, the ACC is always found under, in, or on top of biofilms, commonly in close proximity to crystalline calcite and/or aragonite. Textural evidence indicates that the ACC probably developed in microdomains that develop in the complex biofilm hydrogels. Critically, there is no evidence to support the notion that the nanoparticles are calcified nannobacteria. In the Chinese springs, ACC appears to play a formative role in the development of wheat-sheaf arrays of aragonite crystals and some of the calcite crystals. Hollow cores in some of the aragonite bundles probably formed as ACC was dissolved and many of the aragonite crystals appear to have developed as ACC recrystallized. Similarly, layers of ACC that coat the surfaces of some calcite crystals could be diagenetically transformed into calcite. The development of ACC in hot spring systems may be widespread and may play a critical but transitory role in the development of crystalline CaCO3 in these high temperature environments.

Stable isotope tracing of trout hatchery carbon to sediments and foodwebs of limestone spring creeks

Energy Technology Data Exchange (ETDEWEB)

Hurd, Todd M. [Department of Biology, Shippensburg University, 1871 Old Main Dr., Shippensburg, PA 17257 (United States)], E-mail: tmhurd@ship.edu; Jesic, Slaven; Jerin, Jessica L.; Fuller, Nathan W.; Miller, David [Department of Biology, Shippensburg University, 1871 Old Main Dr., Shippensburg, PA 17257 (United States)

2008-11-01

Limestone springs support productive ecosystems and fisheries, yet aquaculture may modify or impair these ecosystems. We determined trout hatchery organic contribution to spring creek sediments and foodwebs with natural abundance stable isotope methods. Hatchery feed, waste, and trout were significantly enriched in {delta}{sup 13}C relative to autotrophs and wild fish. Spring creek sediments were enriched in {delta}{sup 13}C toward the hatchery endmember relative to reference streams without hatcheries and relative to a larger larger-order, spring-influenced stream. Contribution of hatchery C to spring creek sediments was greatest during March and associated with greatest sediment %C. Contribution of hatchery C to pollution-tolerant isopod diet was 39-51% in a stream receiving limestone spring water via hatchery effluent. Isopods of one spring creek also relied on hatchery-derived C within one month of hatchery closure. Four years later, less pollution pollution-tolerant amphipods dominated and consumed non-vascular over vascular autotrophs (86%). Isopods of a second spring creek with an active hatchery did not appear to be using hatchery matter directly, but were enriched in {delta}{sup 34}S relative to a spring creek tributary with no hatchery influence. Isopods in both of these streams were relatively enriched in {delta}{sup 15}N, indicating general nutrient enrichment from surrounding agricultural land use. The contribution of hatchery vs. wild fish in diet of herons and egrets was traced with {delta}{sup 13}C of guano. These birds were strongly dependent on stocked trout in a spring creek with a recently closed state trout hatchery, and also near another large, state-run hatchery. Heron dependence on hatchery fish in the spring creek decreased with time since hatchery closure. Use of stable isotope natural abundance techniques in karst spring creeks can reveal stream impairment due to aquaculture, specific C sources to bio-indicating consumers, losses of

Stable isotope tracing of trout hatchery carbon to sediments and foodwebs of limestone spring creeks

International Nuclear Information System (INIS)

Hurd, Todd M.; Jesic, Slaven; Jerin, Jessica L.; Fuller, Nathan W.; Miller, David

2008-01-01

Limestone springs support productive ecosystems and fisheries, yet aquaculture may modify or impair these ecosystems. We determined trout hatchery organic contribution to spring creek sediments and foodwebs with natural abundance stable isotope methods. Hatchery feed, waste, and trout were significantly enriched in δ 13 C relative to autotrophs and wild fish. Spring creek sediments were enriched in δ 13 C toward the hatchery endmember relative to reference streams without hatcheries and relative to a larger larger-order, spring-influenced stream. Contribution of hatchery C to spring creek sediments was greatest during March and associated with greatest sediment %C. Contribution of hatchery C to pollution-tolerant isopod diet was 39-51% in a stream receiving limestone spring water via hatchery effluent. Isopods of one spring creek also relied on hatchery-derived C within one month of hatchery closure. Four years later, less pollution pollution-tolerant amphipods dominated and consumed non-vascular over vascular autotrophs (86%). Isopods of a second spring creek with an active hatchery did not appear to be using hatchery matter directly, but were enriched in δ 34 S relative to a spring creek tributary with no hatchery influence. Isopods in both of these streams were relatively enriched in δ 15 N, indicating general nutrient enrichment from surrounding agricultural land use. The contribution of hatchery vs. wild fish in diet of herons and egrets was traced with δ 13 C of guano. These birds were strongly dependent on stocked trout in a spring creek with a recently closed state trout hatchery, and also near another large, state-run hatchery. Heron dependence on hatchery fish in the spring creek decreased with time since hatchery closure. Use of stable isotope natural abundance techniques in karst spring creeks can reveal stream impairment due to aquaculture, specific C sources to bio-indicating consumers, losses of farmed fish to predation, and potential exposure

Geologic context of large karst springs and caves in the Ozark National Scenic Riverways, Missouri

Science.gov (United States)

Weary, David J.; Orndorff, Randall C.

2016-01-01

The ONSR is a karst park, containing many springs and caves. The “jewels” of the park are large springs, several of first magnitude, that contribute significantly to the flow and water quality of the Current River and its tributaries. Completion of 1:24,000-scale geologic mapping of the park and surrounding river basin, along with synthesis of published hydrologic data, allows us to examine the spatial relationships between the springs and the geologic framework to develop a conceptual model for genesis of these springs. Based on their similarity to mapped spring conduits, many of the caves in the ONSR are fossil conduit segments. Therefore, geologic control on the evolution of the springs also applies to speleogenesis in this part of the southern Missouri Ozarks.Large springs occur in the ONSR area because: (1) the Ozark aquifer, from which they rise, is chiefly dolomite affected by solution via various processes over a long time period, (2) Paleozoic hypogenic fluid migration through these rocks exploited and enhanced flow-paths, (3) a consistent and low regional dip of the rocks off of the Salem Plateau (less than 2° to the southeast) allows integration of flow into large groundwater basins with a few discreet outlets, (4) the springs are located where the rivers have cut down into structural highs, allowing access to water from stratigraphic units deeper in the aquifer thus allowing development of springsheds that have volumetrically larger storage than smaller springs higher in the section, and (5) quartz sandstone and bedded chert in the carbonate stratigraphic succession that are locally to regionally continuous, serve as aquitards that locally confine groundwater up dip of the springs creating artesian conditions. This subhorizontal partitioning of the Ozark aquifer allows contributing areas for different springs to overlap, as evidenced by dye traces that cross adjacent groundwater basin boundaries, and possibly contributes to alternate flow routes

Spring for It: First Novels

Science.gov (United States)

Hoffert, Barbara

2010-01-01

How do publishers describe the first novels they will be releasing this spring and summer? "Amazing," "fabulous," and "unique" are words that pop up frequently, though hats off to one publicist forthright or cheeky enough to call a work "weird Western/horror." The proof of such praise is in the reading, but why not check out this preview of first…

77 FR 9958 - Spring Pygmy Sunfish Candidate Conservation Agreement With Assurances; Receipt of Application for...

Science.gov (United States)

2012-02-21

... stained spring water, spring runs, and associated spring-fed wetlands (Warren 2004). The species is highly... disclosure, we cannot guarantee that we will be able to do so. Dated: February 14, 2012. Stephen M. Ricks...

Study of the corrosion fatigue resistance of steel grades for automotive suspension springs

Energy Technology Data Exchange (ETDEWEB)

Mougin, J. [Ascometal CREAS, BP70045, F-57301 Hagondange Cedex (France); Mostacchi, A. [Ascometal Developpement, BP17, F-38570 Le Cheylas (France); Hersart, Y. [Allevard Rejna Autosuspensions CRDT, 201 Rue de Sin-le-Noble, BP629, F-59506 Douai Cedex (France)

2004-07-01

In order to reduce the total weight of vehicles for ecological and economical reasons, the car makers use down-sizing for several components of the cars. Concerning helical suspension springs, the size of the bar diameter and the number of spring coils are decreased, leading to an increase of the stress level applied on the spring. In this respect, steels with high mechanical properties are required, to achieve a good fatigue resistance of the springs. The corrosion resistance is also important for this application. Indeed, during service, the protective coating applied on the springs can be scratched by gravels, and bare underlying metal can be put in contact with the atmosphere, including humidity, drops of rain but also de-icing salts. Generally speaking, an increase of mechanical properties decreases the corrosion fatigue resistance of the steels. In this respect, a compromise needs to be found, that is why the study of corrosion fatigue resistance is very important. In order to study the corrosion fatigue resistance of spring steels, an original device and test procedure have been set up. Torsional fatigue on specimens is used to simulate the stress applied on each spring coil. The stress levels are chosen to be representative of the actual inservice loads. The specimens are shot-peened and coated in a same way as the actual springs. Scratching of the painting is performed, giving rise to small areas of bare metal. Three types of tests are performed: fatigue in air (taken as the reference level), fatigue on specimens which have been corroded previously (test similar to the spring-makers practice) and coupled corrosion fatigue. The mechanisms involved in corrosion fatigue have been studied. For all the specimens, crack initiated on corrosion pits. For the specimens corroded prior fatigue testing, the corrosion pits can be quite severe. In this case, these pits act as a surface defect which increases locally the stress concentration and accelerates the crack

Finite element analysis of optimized H shape spring in a nuclear fuel spacer grid by using contact definition

International Nuclear Information System (INIS)

Kim, Jae-Yong; Yoon, Kyung-Ho

2007-01-01

The primary role of the grid springs in spacer grid is to hold the fuel rods in an appropriate position using friction force and to prevent the fuel rods dropping during reactor operation. The spring force decreases as the fuel burn-up increases since the spring stiffness is degraded due to the high temperature and the irradiation effect in the reactor core. So this phenomenon has to be considered when the initial spring force of grid spring is designed. To check whether the spring have suitable spring force, the characterization test of spring is conducted. In this paper, finite element analysis using contact definition is established for prediction the spring stiffness without test. The test and analysis results are compared to check the availability of finite element model for investing the spring characteristics in assembly condition. (author)

Report on fiscal 1998 investigation of Jozankei hot spring conservation and hot spring structure; 1998 nendo Jozankei onsen hozen chosa. Onsen kozo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

With the purpose of evaluating recoverable hot water quantity and elucidating the change over a long term, investigations were carried out, with the results summarized, on the geology, alteration zone, gravitational analysis, fluid geochemistry and hydraulics in the area. The investigations covered the area of 7 km x 6 km in about 30 km southwest of Sapporo City and were performed for the period from September 10, 1998 to October 31, 1999. The results were as follows. In the Jozankei area, with the Usubetu layer in the Old Tertiary system as the basement, layers are superposed from the Palaeogene Oligocene to the Quaternary Pleistocene. Distributing in various places between Yunosawa vicinity and Jozankei Hot Spring area are acid to neutral geothermal alteration zones. The hot spring gushing-out zone in the Jozankei hot spring area is supposed to be regulated by side-by-side cracks in the NE-SW direction. It was inferred from tritium concentration and a minor component ratio that, as the mechanism of forming a hot spring, water of precipitation origin circulating and residing for a long time on the Usubetsu layer which is marine sediment is heated by a volcanic heat source latent in the depth. (NEDO)

Monitoring Springs in the Mojave Desert Using Landsat Time Series Analysis

Science.gov (United States)

Potter, Christopher S.

2018-01-01

The purpose of this study, based on Landsat satellite data was to characterize variations and trends over 30 consecutive years (1985-2016) in perennial vegetation green cover at over 400 confirmed Mojave Desert spring locations. These springs were surveyed between in 2015 and 2016 on lands managed in California by the U.S. Bureau of Land Management (BLM) and on several land trusts within the Barstow, Needles, and Ridgecrest BLM Field Offices. The normalized difference vegetation index (NDVI) from July Landsat images was computed at each spring location and a trend model was first fit to the multi-year NDVI time series using least squares linear regression.Â

Natural Radioactivity of Thermal Springs in Croatia

International Nuclear Information System (INIS)

Marovic, G.; Sencar, J.; Cesar, D.

1998-01-01

The Republic of Croatia is rich in thermal and mineral springs, which are widely popular for medical therapy, tourism, recreation, rehabilitation and drinking. Considering the popularity of the spas and the habits of our population to use the beneficial effects of these springs it is of interest to estimate the radiation doses received by patients or tourists staying in the spas. In view of this, the Radiation Protection Unit of the Institute for Medical Research and Occupational Health in Zagreb has been engaged in a research programme dealing with the natural radioactivity concentration in the Croatian thermal and mineral waters. The aim of this paper was to estimate total natural radioactivity (Ra, Ra decay) in thermal and mineral waters from the several spas in Croatia. On basis of the obtained data the Ra and Ra activity ratio was calculated for each investigated spa. In this study possible effects of natural radioactivity were determined for each radionuclide using a derived concentration (DC) for a group of individuals for municipal drinking water supplies. Values exceeding DC represent radionuclide concentrations for radioactive waste. Total percentage ratio for each spring was also calculated. Since natural radioactivity in some spas exceeds DC value the practise of using these waters should be regularly estimated and monitored in order to avoid any possible health effects. (author)

RIKEN-JAERI 8-GeV synchrotron radiation project - SPring-8

International Nuclear Information System (INIS)

Awaya, Yohko

1990-01-01

The plan of an 8-GeV synchrotron radiation facility, which is called SPring-8 (Super Photon Ring-8GeV), had been proposed by Science and Technology Agency (STA) in Japan and it was decided that its construction would be started from April 1990. An atomic physics group in Japan had the first meeting in December 1988 to discuss the future studies of atomic physics and related problems at SPring-8 and plans of research and development (R and D) for them. Their report was published in May 1990. In this report, an outline of SPring-8 is described. Results of the discussions of Japanese working group of atomic physics and the present status of R and D of this group will be presented by M. Kimura in this workshop

Diversity and Ecological Functions of Crenarchaeota in Terrestrial Hot Springs of Tengchong, China

Science.gov (United States)

Li, W.; Song, Z.; Chen, J.; Jiang, H.; Zhou, E.; Wang, F.; Xiao, X.; Zhang, C.

2010-12-01

The diversity and potential ecological functions of Crenarchaeota were investigated in eight terrestrial hot springs (pH: 2.8-7.7; temperature: 43.6-96 C) located in Tengchong, China, using 16S rRNA gene phylogenetic analysis. A total of 826 crenarchaeotal clones were analyzed and a total of 47 Operational taxonomic units (OTUs) were identified. Most (93%) of the identified OTUs were closely related (89-99%) to those retrieved from hot springs and other thermal environments. Our data showed that temperature may predominate over pH in affecting crenarchaeotal diversity in Tengchong hot springs. Crenarchaeotal diversity in moderate-temperature (59 to 77 C) hot springs was the highest, indicating that the moderate-temperature hot springs are more inclusive for Crenarchaeota. To understand what ecological functions these Crenarchaeota may play in Tengchong hot springs, we isolated the environmental RNA and constructed four cDNA clone libraries of the archaeal accA gene that encodes Acetyl CoA carboxylase. The accA gene represents one of the key enzymes responsible for the CO2 fixation in the 3-hydroxypropionate/4-hydroxybutyrate pathway. The results of phylogenetic analysis showed all the transcribed accA gene sequences can be classified into three large clusters, with the first one being affiliated with marine crenarchaeota, the second one with cultured crenarchaeota, and the third one with Chlorobi (Green sulfur bacteria), which have been proved to employ the 3-hydroxypropionate/4-hydroxybutyrate pathway. The long-branch distances of the phylogenetic tree suggest that these sequences represent novel accA-like gene. Our results also showed that sequences of the accA-like gene from the same hot spring belonged to one cluster, which suggests that a single crenarchaeotal group may fix CO2 via 3-hydroxypropionate/4-hydroxybutyrate pathway in the investigated hot springs.

A clinical study of space closure with nickel-titanium closed coil springs and an elastic module.

Science.gov (United States)

Samuels, R H; Rudge, S J; Mair, L H

1998-07-01

A previous study has shown that a 150-gram nickel-titanium closed coil spring (Sentalloy, GAC International Inc.) closed spaces more quickly and more consistently than an elastic module (Alastik, Unitec/3M). This study used the same friction sensitive sliding mechanics of pitting the six anterior teeth against the second bicuspid and first molars, to examine the rate of space closure of 100-gram and 200-gram nickel-titanium closed coil springs. The results for the three springs and elastic module were compared. The nickel-titanium closed coil springs produced a more consistent space closure than the elastic module. The 150- and 200-gram springs produced a faster rate of space closure than the elastic module or the 100-gram spring. No significant difference was noted between the rates of closure for the 150- and the 200-gram springs.

Nitrogen cycling in Hot Spring Sediments and Biofilms (Invited)

Science.gov (United States)

Meyer-Dombard, D. R.; Burton, M. S.; Havig, J. R.; Shock, E.

2010-12-01

Over the past several decades, gene-targeted analyses have revealed that microbial communities in hydrothermal environments can be surprisingly diverse. However, we know shockingly little about basic ecological functions such as carbon and nitrogen cycling or community shifts over time, or environmental parameters such as growth criteria. Previous work has shown that carbon cycling in one hot spring in Yellowstone National Park [“Bison Pool”] and its associated runoff channel functions as a complex system. Analysis of carbon and nitrogen isotopes in biofilms across a temperature and chemical gradient at this location revealed that multiple autotrophic carbon fixation pathways are functioning in this system, and nitrogen fixation varies across the chemosynthetic/photosynthetic ecotone [1]. Further, sequencing of metagenomes from multiple locations at “Bison Pool” has indicated the presence of genes involved in carbon fixation [both phototrophic and autotrophic], and heterotrophy, as well as nitrogen fixation [2]. Studies from other Yellowstone locations have also found genetic evidence for carbon and nitrogen fixation [3-5]. The role of individual microbes in nitrogen cycling as environmental conditions vary over space and time is the focus of this study. Here, we explore the diversity of nifH [nitrogen fixation], nirK [nitrite reduction] and amoA [ammonia oxidation] genes across a variety of Yellowstone environments. Environmental nucleic acids were extracted, and the presence/absence of Bacteria and Archaea determined by PCR. In addition, PCR-directed screens reveal the presence or absence of the aforementioned functional genes, indicating genetic capacity for nitrogen cycling. We have examined the transition of genetic diversity and genetic capacity within sediments and biofilms at the chemosynthetic/photosynthetic ecotone in several hot springs spanning ranges of pH and geochemical conditions. By sampling across this ecotone, changes in the genetic

Comparison of various spring analogy related mesh deformation techniques in two-dimensional airfoil design optimization

Science.gov (United States)

Yang, Y.; Özgen, S.

2017-06-01

During the last few decades, CFD (Computational Fluid Dynamics) has developed greatly and has become a more reliable tool for the conceptual phase of aircraft design. This tool is generally combined with an optimization algorithm. In the optimization phase, the need for regenerating the computational mesh might become cumbersome, especially when the number of design parameters is high. For this reason, several mesh generation and deformation techniques have been developed in the past decades. One of the most widely used techniques is the Spring Analogy. There are numerous spring analogy related techniques reported in the literature: linear spring analogy, torsional spring analogy, semitorsional spring analogy, and ball vertex spring analogy. This paper gives the explanation of linear spring analogy method and angle inclusion in the spring analogy method. In the latter case, two di¨erent solution methods are proposed. The best feasible method will later be used for two-dimensional (2D) Airfoil Design Optimization with objective function being to minimize sectional drag for a required lift coe©cient at di¨erent speeds. Design variables used in the optimization include camber and thickness distribution of the airfoil. SU2 CFD is chosen as the §ow solver during the optimization procedure. The optimization is done by using Phoenix ModelCenter Optimization Tool.

Accumulation of wet-deposited radiocaesium and radiostrontium by spring oilseed rape (Brássica napus L.) and spring wheat (Tríticum aestívum L.)

International Nuclear Information System (INIS)

Bengtsson, Stefan B.; Eriksson, Jan; Gärdenäs, Annemieke I.; Vinichuk, Mykhailo; Rosén, Klas

2013-01-01

The accumulation of 134 Cs and 85 Sr within different parts of spring oilseed rape and spring wheat plants was investigated, with a particular focus on transfer to seeds after artificial wet deposition at different growth stages during a two-year field trial. In general, the accumulation of radionuclides in plant parts increased when deposition was closer to harvest. The seed of spring oilseed rape had lower concentrations of 85 Sr than spring wheat grain. The plants accumulated more 134 Cs than 85 Sr. We conclude that radionuclides can be transferred into human food chain at all growing stages, especially at the later stages. The variation in transfer factors during the investigation, and in comparison to previous results, implies the estimation of the risk for possible transfer of radionuclides to seeds in the event of future fallout during a growing season is still subject to considerable uncertainty. -- Highlights: •Accumulation of 134 Cs and 85 Sr in plants increased the closer to harvest the nuclides were deposited. • 134 Cs and 85 Sr concentrations in seeds were highest when deposited after flowering. •Activity concentrations of 134 Cs in spring oilseed rape were higher than the activity concentrations of 85 Sr. •Oilseed rape redistributes 134 Cs and 85 Sr to seed at a lower rate than wheat redistributes 134 Cs and 85 Sr to grain. -- Intercepted radionuclides can be transferred into the food chain for humans

76 FR 72722 - Helical Spring Lock Washers From China and Taiwan

Science.gov (United States)

2011-11-25

... Spring Lock Washers From China and Taiwan Determination On the basis of the record \\1\\ developed in the... antidumping duty orders on helical spring lock washers from China and Taiwan would be likely to lead to continuation or recurrence of material injury to an industry in the United States within a reasonably...

Neutron activation analysis of the rare earth elements in Nasu hot springs

International Nuclear Information System (INIS)

Ikeda, Nagao; Takahashi, Naruto.

1978-01-01

Eleven rare earth elements (lanthanum, cerium, neodymium, samarium, europium, gadolinium, terbium, holmium, thulium, ytterbium and lutetium) in hot spring waters and sinter deposits in the Nasu area were determined by the neutron activation method. The rare earth elements in hot spring water were preconcentrated in ferric hydroxide precipitate and neutron-irradiated. The rare earth elements were chemically separated into lighter and heavier groups and the activity of each group was measured with a Ge(Li) detector. Distribution of the rare earth elements between the hot spring water and the sinter deposit was also discussed. (auth.)

Numerical Modelling of Metal-Elastomer Spring Nonlinear Response for Low-Rate Deformations

Directory of Open Access Journals (Sweden)

Sikora Wojciech

2018-03-01

Full Text Available Advanced knowledge of mechanical characteristics of metal-elastomer springs is useful in their design process and selection. It can also be used in simulating dynamics of machine where such elements are utilized. Therefore this paper presents a procedure for preparing and executing FEM modelling of a single metal-elastomer spring, also called Neidhart’s spring, for low-rate deformations. Elastomer elements were made of SBR rubber of two hardness values: 50°Sh and 70°Sh. For the description of material behaviour the Bergström-Boyce model has been used.

Longer wings for faster springs - wing length relates to spring phenology in a long-distance migrant across its range.

Science.gov (United States)

Hahn, Steffen; Korner-Nievergelt, Fränzi; Emmenegger, Tamara; Amrhein, Valentin; Csörgő, Tibor; Gursoy, Arzu; Ilieva, Mihaela; Kverek, Pavel; Pérez-Tris, Javier; Pirrello, Simone; Zehtindjiev, Pavel; Salewski, Volker

2016-01-01

In migratory birds, morphological adaptations for efficient migratory flight often oppose morphological adaptations for efficient behavior during resident periods. This includes adaptations in wing shape for either flying long distances or foraging in the vegetation and in climate-driven variation of body size. In addition, the timing of migratory flights and particularly the timely arrival at local breeding sites is crucial because fitness prospects depend on site-specific phenology. Thus, adaptations for efficient long-distance flights might be also related to conditions at destination areas. For an obligatory long-distance migrant, the common nightingale, we verified that wing length as the aerodynamically important trait, but not structural body size increased from the western to the eastern parts of the species range. In contrast with expectation from aerodynamic theory, however, wing length did not increase with increasing migration distances. Instead, wing length was associated with the phenology at breeding destinations, namely the speed of local spring green-up. We argue that longer wings are beneficial for adjusting migration speed to local conditions for birds breeding in habitats with fast spring green-up and thus short optimal arrival periods. We suggest that the speed of spring green-up at breeding sites is a fundamental variable determining the timing of migration that fine tune phenotypes in migrants across their range.

An observation-based progression modeling approach to spring and autumn deciduous tree phenology

Science.gov (United States)

Yu, Rong; Schwartz, Mark D.; Donnelly, Alison; Liang, Liang

2016-03-01

It is important to accurately determine the response of spring and autumn phenology to climate change in forest ecosystems, as phenological variations affect carbon balance, forest productivity, and biodiversity. We observed phenology intensively throughout spring and autumn in a temperate deciduous woodlot at Milwaukee, WI, USA, during 2007-2012. Twenty-four phenophase levels in spring and eight in autumn were recorded for 106 trees, including white ash, basswood, white oak, boxelder, red oak, and hophornbeam. Our phenological progression models revealed that accumulated degree-days and day length explained 87.9-93.4 % of the variation in spring canopy development and 75.8-89.1 % of the variation in autumn senescence. In addition, the timing of community-level spring and autumn phenophases and the length of the growing season from 1871 to 2012 were reconstructed with the models developed. All simulated spring phenophases significantly advanced at a rate from 0.24 to 0.48 days/decade ( p ≤ 0.001) during the 1871-2012 period and from 1.58 to 2.00 days/decade ( p coloration) and 0.50 (full-leaf coloration) days/decade ( p coloration and leaf fall, and suggested accelerating simulated ecosystem responses to climate warming over the last four decades in comparison to the past 142 years.

SHORT COMMUNICATION TRITERPENE COMPOUNDS FROM ...

African Journals Online (AJOL)

a

Grison, P.L.; McKey, M.H.; Jaco, M.G.; Jean-Marie, B. Phytochemistry 2002, 61, 61. 3. Sergio, R.P.S.; Hee, B.C.; Young, G.S.; Thawatchai, S.; Vichai, R.; Norman, R.F.; Geoffrey,. A.C.; John, M.P.; Duglas, A.K. Planta Med. 2002, 68, 186. 4. Hong, J.Z.; Pamela, A.T.; Zeynep, A.; Ghee, T.T.; Yoko, S.; Hashimoto, K.; Masaya, N.;.

The Silent Spring of Rachel Carson.

Science.gov (United States)

Kerstetter, Ned

1996-01-01

Presents a lesson plan examining Rachel Carson's call to arms concerning the harmful consequences of pesticides. Students view a video documentary on Carson's work and read a synopsis of her book, "Silent Spring." Assessment is provided by various activities including writing assignments, creating posters, and editorial cartoons. (MJP)

Injector linac of SPring-8

International Nuclear Information System (INIS)

Yoshikawa, H.; Hori, T.; Suzuki, S.; Yanagida, K.; Itoh, Y.; Mizuno, A.; Taniuchi, T.; Sakaki, H.; Kuba, A.; Fukushima, S.; Kobayashi, T.; Asaka, T.; Yokomizo, H.

1996-01-01

The linac that is SPring-8 injector was completed and started operation from August 1. A beam was able to be transported to the final beam dumping at a tail end on August 8. From now on this linac carries out beam adjustment and be scheduled to do a beam injection to a synchrotron in October. The construction and fundamental performance of the linac are described. (author)

Controlling proteins through molecular springs.

Science.gov (United States)

Zocchi, Giovanni

2009-01-01

We argue that the mechanical control of proteins-the notion of controlling chemical reactions and processes by mechanics-is conceptually interesting. We give a brief review of the main accomplishments so far, leading to our present approach of using DNA molecular springs to exert controlled stresses on proteins. Our focus is on the physical principles that underlie both artificial mechanochemical devices and natural mechanisms of allostery.

Spring Framework 5: Themes & Trends

CERN Document Server

CERN. Geneva

2017-01-01

Spring Framework 5.0/5.1, scheduled for release in early/late 2017, focuses on several key themes: reactive web applications based on Reactive Streams, comprehensive support for JDK 9 and HTTP/2, as well as the latest API generations in the Enterprise Java ecosystem. This talk presents the overall story in the context of wider industry trends, highlighting Spring’s unique programming model strategy.

Methods to estimate annual mean spring discharge to the Snake River between Milner Dam and King Hill, Idaho

Science.gov (United States)

Kjelstrom, L.C.

1995-01-01

Many individual springs and groups of springs discharge water from volcanic rocks that form the north canyon wall of the Snake River between Milner Dam and King Hill. Previous estimates of annual mean discharge from these springs have been used to understand the hydrology of the eastern part of the Snake River Plain. Four methods that were used in previous studies or developed to estimate annual mean discharge since 1902 were (1) water-budget analysis of the Snake River; (2) correlation of water-budget estimates with discharge from 10 index springs; (3) determination of the combined discharge from individual springs or groups of springs by using annual discharge measurements of 8 springs, gaging-station records of 4 springs and 3 sites on the Malad River, and regression equations developed from 5 of the measured springs; and (4) a single regression equation that correlates gaging-station records of 2 springs with historical water-budget estimates. Comparisons made among the four methods of estimating annual mean spring discharges from 1951 to 1959 and 1963 to 1980 indicated that differences were about equivalent to a measurement error of 2 to 3 percent. The method that best demonstrates the response of annual mean spring discharge to changes in ground-water recharge and discharge is method 3, which combines the measurements and regression estimates of discharge from individual springs.

River Intrusion in Karst Springs in Eogenetic Aquifers: Implications for Speleogenesis

Science.gov (United States)

Martin, J. B.; Gulley, J.; Screaton, E. J.

2008-12-01

Conceptual models of speleogenesis generally assume uni-directional transport in integrated conduit systems from discrete recharge points to discharge at karst springs. Estavelles, however, are karst springs that function intermittently as discrete recharge points when river stage rises more rapidly than local aquifer heads. As river water chemistry changes between baseflow and floods, estavelles should influence mass transport through (e.g. organic carbon, nutrients, and oxygen) and speleogenesis within karst systems. Estavelles are common in our study area in north-central Florida, particularly along the lower reaches of the Santa Fe River, where it flows across the unconfined karstic Floridan aquifer. River stage in this unconfined region can rise much faster than aquifer heads when large amounts of rain fall on the confined regions in its upper reaches. Backflooding into the estavelles during elevated river stage drives river water into the ground, causing some springs to reverse and other springs to recirculate large volumes of river water. Floodwaters originating in the confined region are highly undersaturated with respect to calcite, and thus river water transitions from slightly supersaturated to highly undersaturated with respect to calcite during flood events. As a result, conduits connected to estavelles are continuously enlarged as springs reverse or recirculate calcite-undersaturated river water. It has been suggested that currently flooded caves (i.e. karst conduits) associated with springs in Florida formed entirely underwater because speleothems, which are prevalent in flooded caves in the Yucatan and Bahamas, have not been observed by cave divers. Results of this study indicate that the absence of speleothems does not necessarily provide evidence of a continuous phreatic history for underwater caves. Instead speleothems that formed in caves while dry could have been dissolved by backflooding of estavelles with undersaturated water

Online analysis: Deeper insights into water quality dynamics in spring water.

Science.gov (United States)

Page, Rebecca M; Besmer, Michael D; Epting, Jannis; Sigrist, Jürg A; Hammes, Frederik; Huggenberger, Peter

2017-12-01

We have studied the dynamics of water quality in three karst springs taking advantage of new technological developments that enable high-resolution measurements of bacterial load (total cell concentration: TCC) as well as online measurements of abiotic parameters. We developed a novel data analysis approach, using self-organizing maps and non-linear projection methods, to approximate the TCC dynamics using the multivariate data sets of abiotic parameter time-series, thus providing a method that could be implemented in an online water quality management system for water suppliers. The (TCC) data, obtained over several months, provided a good basis to study the microbiological dynamics in detail. Alongside the TCC measurements, online abiotic parameter time-series, including spring discharge, turbidity, spectral absorption coefficient at 254nm (SAC254) and electrical conductivity, were obtained. High-density sampling over an extended period of time, i.e. every 45min for 3months, allowed a detailed analysis of the dynamics in karst spring water quality. Substantial increases in both the TCC and the abiotic parameters followed precipitation events in the catchment area. Differences between the parameter fluctuations were only apparent when analyzed at a high temporal scale. Spring discharge was always the first to react to precipitation events in the catchment area. Lag times between the onset of precipitation and a change in discharge varied between 0.2 and 6.7h, depending on the spring and event. TCC mostly reacted second or approximately concurrent with turbidity and SAC254, whereby the fastest observed reaction in the TCC time series occurred after 2.3h. The methodological approach described here enables a better understanding of bacterial dynamics in karst springs, which can be used to estimate risks and management options to avoid contamination of the drinking water. Copyright © 2017 Elsevier B.V. All rights reserved.

Origin and geochemistry of saline spring waters in the Athabasca oil sands region, Alberta, Canada

International Nuclear Information System (INIS)

Gue, Anita E.; Mayer, Bernhard; Grasby, Stephen E.

2015-01-01

Highlights: • Saline groundwater enters the Athabasca and Clearwater rivers in the AOSR via springs. • High TDS is due to subsurface dissolution of Devonian evaporites and carbonates. • Low δ 18 O values, and 3 H and 14 C data suggest some Laurentide glacial meltwater input. • Bacterial sulfate reduction, methanogenesis, and CH 4 oxidation were identified. • Metal and PAH contents are reported; bitumen does not appear to be major influence. - Abstract: The geochemistry of saline spring waters in the Athabasca oil sands region (AOSR) in Alberta (Canada) discharging from Devonian carbonate rocks into the Athabasca and Clearwater rivers was characterized for major ions, trace elements, dissolved gases, and polycyclic aromatic hydrocarbons (PAHs). In addition, stable isotope analyses of H 2 O, SO 4 , dissolved inorganic carbon (DIC), Sr, and CH 4 were used to trace the sources of spring waters and their dissolved solutes, and to identify subsurface processes affecting water chemistry. The spring waters had δ 18 O values as low as −23.5‰, suggesting they are composed of up to 75% Laurentide glacial meltwater. Tritium and radiocarbon age-dating results, analyzed for three spring waters, supported a glacial origin. The high salinity of the spring waters (TDS 7210–51,800 mg/L) was due to dissolution of Devonian evaporite and carbonate deposits in the subsurface. Spring waters were affected by bacterial (dissimilatory) sulfate reduction, methanogenesis, and methane oxidation. Trace elements were present in spring waters at varying concentrations, with only one spring containing several predominant oil sands metals (As, Fe, Mo, Ni, Se, Zn) suggesting bitumen as a source. Five springs contained elements (Al, As, B, Fe, Se) at concentrations exceeding water quality guidelines for the protection of aquatic life. Seven PAHs were detected in spring waters (total PAH concentrations ranged from 7.3 to 273.6 ng/L), but most springs contained a maximum of two PAHs

Influence of Poisson's ratio variation on lateral spring constant of atomic force microscopy cantilevers

International Nuclear Information System (INIS)

Yeh, M.-K.; Tai, N.-Ha; Chen, B.-Y.

2008-01-01

Atomic force microscopy (AFM) can be used to measure the surface morphologies and the mechanical properties of nanostructures. The force acting on the AFM cantilever can be obtained by multiplying the spring constant of AFM cantilever and the corresponding deformation. To improve the accuracy of force experiments, the spring constant of AFM cantilever must be calibrated carefully. Many methods, such as theoretical equations, the finite element method, and the use of reference cantilever, were reported to obtain the spring constant of AFM cantilevers. For the cantilever made of single crystal, the Poisson's ratio varies with different cantilever-crystal angles. In this paper, the influences of Poisson's ratio variation on the lateral spring constant and axial spring constant of rectangular and V-shaped AFM cantilevers, with different tilt angles and normal forces, were investigated by the finite element analysis. When the cantilever's tilt angle is 20 deg. and the Poisson's ratio varies from 0.02 to 0.4, the finite element results show that the lateral spring constants decrease 11.75% for the rectangular cantilever with 1 μN landing force and decrease 18.60% for the V-shaped cantilever with 50 nN landing force, respectively. The influence of Poisson's ratio variation on axial spring constant is less than 3% for both rectangular and V-shaped cantilevers. As the tilt angle increases, the axial spring constants for rectangular and V-shaped cantilevers decrease substantially. The results obtained can be used to improve the accuracy of the lateral force measurement when using atomic force microscopy

Evening daylight may cause adolescents to sleep less in spring than in winter

Science.gov (United States)

Figueiro, Mariana G.; Rea, Mark S.

2012-01-01

Sleep restriction commonly experienced by adolescents can stem from greater sleep pressure by the homeostatic processes and from phase delays of the circadian system. With regard to the latter potential cause, we hypothesized that because there is more natural evening light during the spring than winter, a sample of adolescent students would be more phase delayed in spring than in winter, would have later sleep onset times and, because of fixed school schedules, would have shorter sleep durations. Sixteen eighth-grade subjects were recruited for the study. We collected sleep logs and saliva samples to determine their dim light melatonin onset (DLMO), a well-established circadian marker. Actual circadian light exposures experienced by a subset of twelve subjects over the course of seven days in winter and in spring using a personal, head-worn, circadian light measurement device are also reported here. Results showed that this sample of adolescents was exposed to significantly more circadian light in spring than in winter, especially in the evening hours when light exposure would likely delay circadian phase. Consistent with the light data, DLMO and sleep onset times were significantly more delayed, and sleep durations were significantly shorter in spring than in winter. The present ecological study of light, circadian phase, and self-reported sleep suggests that greater access to evening daylight in the spring may lead to sleep restriction in adolescents while attending school. Therefore, lighting schemes that reduce evening light in the spring may encourage longer sleep times in adolescents. PMID:20653452

77 FR 33237 - Saline Valley Warm Springs Management Plan/Environmental Impact Statement, Death Valley National...

Science.gov (United States)

2012-06-05

... Valley Warm Springs Management Plan/Environmental Impact Statement, Death Valley National Park, Inyo... an Environmental Impact Statement for the Saline Valley Warm Springs Management Plan, Death Valley... analysis process for the Saline Valley Warm Springs Management Plan for Death Valley [[Page 33238...

Spring hydrology determines summer net carbon uptake in northern ecosystems

International Nuclear Information System (INIS)

Yi, Yonghong; Kimball, John S; Reichle, Rolf H

2014-01-01

Increased photosynthetic activity and enhanced seasonal CO 2 exchange of northern ecosystems have been observed from a variety of sources including satellite vegetation indices (such as the normalized difference vegetation index; NDVI) and atmospheric CO 2 measurements. Most of these changes have been attributed to strong warming trends in the northern high latitudes (⩾50° N). Here we analyze the interannual variation of summer net carbon uptake derived from atmospheric CO 2 measurements and satellite NDVI in relation to surface meteorology from regional observational records. We find that increases in spring precipitation and snow pack promote summer net carbon uptake of northern ecosystems independent of air temperature effects. However, satellite NDVI measurements still show an overall benefit of summer photosynthetic activity from regional warming and limited impact of spring precipitation. This discrepancy is attributed to a similar response of photosynthesis and respiration to warming and thus reduced sensitivity of net ecosystem carbon uptake to temperature. Further analysis of boreal tower eddy covariance CO 2 flux measurements indicates that summer net carbon uptake is positively correlated with early growing-season surface soil moisture, which is also strongly affected by spring precipitation and snow pack based on analysis of satellite soil moisture retrievals. This is attributed to strong regulation of spring hydrology on soil respiration in relatively wet boreal and arctic ecosystems. These results document the important role of spring hydrology in determining summer net carbon uptake and contrast with prevailing assumptions of dominant cold temperature limitations to high-latitude ecosystems. Our results indicate potentially stronger coupling of boreal/arctic water and carbon cycles with continued regional warming trends. (letters)

Spring Hydrology Determines Summer Net Carbon Uptake in Northern Ecosystems

Science.gov (United States)

Yi, Yonghong; Kimball, John; Reichle, Rolf H.

2014-01-01

Increased photosynthetic activity and enhanced seasonal CO2 exchange of northern ecosystems have been observed from a variety of sources including satellite vegetation indices (such as the Normalized Difference Vegetation Index; NDVI) and atmospheric CO2 measurements. Most of these changes have been attributed to strong warming trends in the northern high latitudes (greater than or equal to 50N). Here we analyze the interannual variation of summer net carbon uptake derived from atmospheric CO2 measurements and satellite NDVI in relation to surface meteorology from regional observational records. We find that increases in spring precipitation and snow pack promote summer net carbon uptake of northern ecosystems independent of air temperature effects. However, satellite NDVI measurements still show an overall benefit of summer photosynthetic activity from regional warming and limited impact of spring precipitation. This discrepancy is attributed to a similar response of photosynthesis and respiration to warming and thus reduced sensitivity of net ecosystem carbon uptake to temperature. Further analysis of boreal tower eddy covariance CO2 flux measurements indicates that summer net carbon uptake is positively correlated with early growing-season surface soil moisture, which is also strongly affected by spring precipitation and snow pack based on analysis of satellite soil moisture retrievals. This is attributed to strong regulation of spring hydrology on soil respiration in relatively wet boreal and arctic ecosystems. These results document the important role of spring hydrology in determining summer net carbon uptake and contrast with prevailing assumptions of dominant cold temperature limitations to high-latitude ecosystems. Our results indicate potentially stronger coupling of boreal/arctic water and carbon cycles with continued regional warming trends.

Late winter feeding stimulates rapid spring development of carniolan honey bee colonies (Apis mellifera carnica)

OpenAIRE

Zlatko Puškadija; Lejla Spiljak; Marin Kovačić

2017-01-01

Unfavourable weather conditions after the queen starts with intensive oviposition during early spring may cause an imbalance in the division of tasks among worker bees in the bee colony. This can lead to slow spring development and poor exploitation of the main spring nectar flows. In order to accelerate the spring development, it is necessary, as a technological measure, to feed supplemental candy to bee colonies. In this research, the necessity of supplemental feeding, as well as the com...

Mg2+-Based Method for the Pertuso Spring Discharge Evaluation

Directory of Open Access Journals (Sweden)

Giuseppe Sappa

2017-01-01

Full Text Available This paper deals with the Environmental Monitoring Plan concerning the catchment work project of the Pertuso karst spring, which is going to be exploited to supply an important drinking water network in the south part of Roma district. The Pertuso Spring, located in the Upper Valley of the Aniene River, is the main outlet of a large karst aquifer, which is one of the most important water resources in the southeast part of Latium Region, Central Italy, used for drinking, agriculture, and hydroelectric supplies. The environmental monitoring activities provided data about one spring and two cross-sections of the Aniene River, from July 2014 to May 2016. A combined approach based on discharge measurements and hydrogeochemical analysis has been used to study flow paths and groundwater–surface water interaction in the study area. Tracer methods are particularly suitable in hydrogeological studies to assess transit times and flow properties in karst aquifers. The analysis of solute contents in the sampling points brought forth the identification of the Mg2+ ion as a conservative tracer in this specific system and, consequently, to the development of a conceptual model based on chemical mass balance for the Pertuso Spring discharge evaluation.

Analysis of Helical Stainless Steel 08X18H10 Spring Relaxation at High Temperature

Directory of Open Access Journals (Sweden)

H. Sun

2015-01-01

Full Text Available The object of this paper is to study a cylindrical helical spring to be applied at high temperatures. The aim of this work is to study the regularity of relaxation stresses in spring and evaluate its long-term stresses.The work allowed us to establish relaxation dependencies of springs under high temperatures. According to the results of creep tests at 600°, the theoretical equation of steel creep was defined concretely. It was then used for the analysis at 350°.The paper presents a created finite element model of spring relaxation. It is the stainless steel 08Х18Н10 spring to be used at the temperature of 350°.In this paper describes the basic theory of creep, considers the relationship between the creep speed and parameters. The changing compression force of springs is analyzed under fixed compression amount.The paper also analyzes the changing length of springs in the free state after various stages of high-temperature relaxation test. It determines the results of compression forces and free length under different amount of compression.The analysis to compare the theoretical calculation of the compression forces with the experimental results is conducted. Computer modeling is created in Abaqus for calculation. Spring relaxation experiments are carried out under fixed compression amount and at the temperature of 350°. It is shown that the simulation results, which are carried out in Abaqus coincide with experimental results. The study shows that it is possible to use the creep equation parameters, based on the experimental results at high temperatures, to predict creep and relaxation properties of springs, which work at less high temperatures. The work results can be used as a basis in designing the springs working at high temperatures.

Microbial ecology of two hot springs of Sikkim: Predominate population and geochemistry.

Science.gov (United States)

Najar, Ishfaq Nabi; Sherpa, Mingma Thundu; Das, Sayak; Das, Saurav; Thakur, Nagendra

2018-10-01

Northeastern regions of India are known for their floral and faunal biodiversity. Especially the state of Sikkim lies in the eastern Himalayan ecological hotspot region. The state harbors many sulfur rich hot springs which have therapeutic and spiritual values. However, these hot springs are yet to be explored for their microbial ecology. The development of neo generation techniques such as metagenomics has provided an opportunity for inclusive study of microbial community of different environment. The present study describes the microbial diversity in two hot springs of Sikkim that is Polok and Borong with the assist of culture dependent and culture independent approaches. The culture independent techniques used in this study were next generation sequencing (NGS) and Phospholipid Fatty Acid Analysis (PLFA). Having relatively distinct geochemistry both the hot springs are thermophilic environments with the temperature range of 50-77 °C and pH range of 5-8. Metagenomic data revealed the dominance of bacteria over archaea. The most abundant phyla were Proteobacteria and Bacteroidetes although other phyla were also present such as Acidobacteria, Nitrospirae, Firmicutes, Proteobacteria, Parcubacteria and Spirochaetes. The PLFA studies have shown the abundance of Gram Positive bacteria followed by Gram negative bacteria. The culture dependent technique was correlative with PLFA studies. Most abundant bacteria as isolated and identified were Gram-positive genus Geobacillus and Anoxybacillus. The genus Geobacillus has been reported for the first time in North-Eastern states of India. The Geobacillus species obtained from the concerned hot springs were Geobacillus toebii, Geobacillus lituanicus, Geobacillus Kaustophillus and the Anoxybacillus species includes Anoxybacillus gonensis and Anoxybacillus Caldiproteolyticus. The distribution of major genera and their statistical correlation analyses with the geochemistry of the springs predicted that the temperature, p

Comparative metagenomics of eight geographically remote terrestrial hot springs

DEFF Research Database (Denmark)

Menzel, Peter; Islin, Sóley Ruth; Rike, Anne Gunn

2015-01-01

Hot springs are natural habitats for thermophilic Archaea and Bacteria. In this paper, we present the metagenomic analysis of eight globally distributed terrestrial hot springs from China, Iceland, Italy, Russia, and the USA with a temperature range between 61 and 92 (∘)C and pH between 1.8 and 7....... A comparison of the biodiversity and community composition generally showed a decrease in biodiversity with increasing temperature and decreasing pH. Another important factor shaping microbial diversity of the studied sites was the abundance of organic substrates. Several species of the Crenarchaeal order...

Clash of Harmonics in Stravinsky's The Rite of Spring

Science.gov (United States)

Ruiz, Michael J.

2018-04-01

This paper describes a fascinating connection between the physics of music and the famous chord in the dissonant rhythmic section of Stravinsky's The Rite of Spring (1913). The analysis of Stravinsky's chord will draw from the physics of harmonics, musical intervals, mathematics, and cognitive psychology. This highly interdisciplinary approach will especially appeal to students typically found in a physics course for non-majors. A video accompanies this paper so that readers and students can hear the construction of Stravinsky's dissonant chord as well as an orchestra performing an excerpt of The Rite of Spring.

Stravinsky: The Rite of Spring. Canticum sacrum

Index Scriptorium Estoniae

1996-01-01

Uuest heliplaadist "Stravinsky: The Rite of Spring. Canticum sacrum. Requiem canticles. Choral Variations on "Vom Himmel hoch". Lausanne Pro Arte Choir, Suisse Romande Chamber Choir and Orchestra, Neeme Järvi" Chandos CHAN 9408 (75 minutes:DDD)

Determination of groundwater travel time in a karst aquifer by stable water isotopes, Tanour and Rasoun spring (Jordan)

Science.gov (United States)

Hamdan, Ibraheem; Wiegand, Bettina; Sauter, Martin; Ptak, Thomas

2016-04-01

Key words: karst aquifers, stable isotopes, water travel time, Jordan. Tanour and Rasoun karst springs are located about 75 kilometers northwest of the city of Amman in Jordan. The aquifer is composed of Upper Cretaceous limestone that exhibits a moderate to high degree of karstification. The two springs represent the main drinking water resources for the surrounding villages. The yearly water production is about 1,135,000 m3/yr for Tanour spring and 125,350 m3/yr for Rasoun spring (MWI 2015). Due to contamination from microbiological pollution (leakage of wastewater from septic tanks) or infiltration of wastewater from local olive presses, drinking water supply from the two springs is frequently interrupted. From November 2014 through March 2015, spring water samples were collected from Tanour and Rasoun spring for the analysis of stable hydrogen and oxygen isotopes to investigate spring response to precipitation and snowmelt events. Both Tanour and Rasoun spring show a fast response to precipitation and snowmelt events, implying short water travel times. Based on the variation of δ 18O and δ 2H in spring discharge, the average maximum water travel time is in the order of 8 days for Tanour spring and 6 days for Rasoun spring. Due to fast water travel times, Tanour and Rasoun spring can be considered as highly vulnerable to pollutants. δ 18O and δ 2H values of Tanour and Rasoun springs parallel other monitored parameter like water temperature, turbidity, electrical conductivity and spring discharge. In addition, a high turbidity peak was monitored in Tanour spring during a pollution event from olive mills wastewater (Hamdan et al., 2016; Hamdan, in prep.). The fast response in both Tanour and Rasoun springs to precipitation events requires monitoring potential sources of pollution within the catchment area. References: MWI (Ministry of Water and Irrigation) (2015) Monthly Production values for Tanour and Rasoun Springs for the time period between 1996 and 2014

The long term sustainability of Mound Springs in South Australia : implications for olympic dam

International Nuclear Information System (INIS)

Mudd, G.M.

1998-01-01

The Mound Springs of South Australia are unique groundwater discharge features of the Great Artesian Basin, a deep regigonal groundwater system that covers over one-fifth of the Australia continent. They are the principal sources of water in the arid and semi-arid inland heart of Australia, and have great ecological, scientific, anthropological and economic significance. Excessive development of the Great Artesian Basin over the past century by European activity has seen an overall decline in the flows from the mound springs, and recent development of the water supply borefields for the WMC Olympic Dam Operations copper-uranium mine in the midst of the most important spring groups has exacerbated this problem. A review of the history of the borefields, an analysis of the impacts on the mound springs, and future recommendations for protection of the springs is presented. (orig.)

Corrective action investigation plan: Cactus Spring Waste Trenches. Revision 2

International Nuclear Information System (INIS)

1997-02-01

This Correction Action Investigation Plan (CAIP) contains environmental sample collection objectives and logic for the CAU No. 426, which includes the Cactus Spring Waste Trenches, CAS No. RG-08-001-RG-CS. The Cactus Spring Waste Trenches are located at the Tonopah Test Range (TTR) which is part of the Nellis Air Force Range, approximately 255 kilometers (km) (140 miles [mi]) northwest of Las Vegas, Nevada, by air. The purpose of this investigation is to generate sufficient data to establish the types of waste buried in the trenches, identify the presence and nature of contamination, determine the vertical extent of contaminant migration below the Cactus Spring Waste Trenches, and determine the appropriate course of action for the site. The potential courses of action for the site are clean closure, closure in place (with or without remediation), or no further action

Vibration of a string against multiple spring-mass-damper stoppers

Science.gov (United States)

Shin, Ji-Hwan; Talib, Ezdiani; Kwak, Moon K.

2018-02-01

When a building sways due to strong wind or an earthquake, the elevator rope can undergo resonance, resulting in collision with the hoist-way wall. In this study, a hard stopper and a soft stopper comprised of a spring-mass-damper system installed along the hoist-way wall were considered to prevent the string from undergoing excessive vibrations. The collision of the string with multiple hard stoppers and multiple spring-mass-damper stoppers was investigated using an analytical method. The result revealed new formulas and computational algorithms that are suitable for simulating the vibration of the string against multiple stoppers. The numerical results show that the spring-mass-damper stopper is more effective in suppressing the vibrations of the string and reducing structural failure. The proposed algorithms were shown to be efficient to simulate the motion of the string against a vibration stopper.

Hydrological response and thermal effect of karst springs linked to aquifer geometry and recharge processes

Science.gov (United States)

Luo, Mingming; Chen, Zhihua; Zhou, Hong; Zhang, Liang; Han, Zhaofeng

2018-03-01

To be better understand the hydrological and thermal behavior of karst systems in South China, seasonal variations in flow, hydrochemistry and stable isotope ratios of five karst springs were used to delineate flow paths and recharge processes, and to interpret their thermal response. Isotopic data suggest that mean recharge elevations are 200-820 m above spring outlets. Springs that originate from high elevations have lower NO3 - concentrations than those originating from lower areas that have more agricultural activity. Measured Sr2+ concentrations reflect the strontium contents of the host carbonate aquifer and help delineate the spring catchment's saturated zone. Seasonal variations of NO3 - and Sr2+ concentrations are inversely correlated, because the former correlates with event water and the latter with baseflow. The mean annual water temperatures of springs were only slightly lower than the local mean annual surface temperature at the outlet elevations. These mean spring temperatures suggest a vertical gradient of 6 °C/vertical km, which resembles the adiabatic lapse rate of the Earth's stable atmosphere. Seasonal temperature variations in the springs are in phase with surface air temperatures, except for Heilongquan (HLQ) spring. Event-scale variations of thermal response are dramatically controlled by the circulation depth of karst systems, which determines the effectiveness of heat exchange. HLQ spring undergoes the deepest circulation depth of 820 m, and its thermal responses are determined by the thermally effective regulation processes at higher elevations and the mixing processes associated with thermally ineffective responses at lower elevations.

Proposed plan for remedial action for the Groundwater Operable Unit at the Chemical Plant Area of the Weldon Spring Site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1999-01-01

This Proposed Plan addresses the remediation of groundwater contamination at the chemical plant area of the Weldon Spring site in Weldon Spring, Missouri. The site is located approximately 48 km (30 mi) west of St. Louis in St. Charles County . Remedial activities at the site will be conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The U.S. Department of Energy (DOE), in conjunction with the U.S. Department of the Army (DA), conducted a joint remedial investigation/feasibility study (RI/FS) to allow for a comprehensive evaluation of groundwater conditions at the Weldon Spring chemical plant area and the Weldon Spring ordnance works area, which is an Army site adjacent to the chemical plant area. Consistent with DOE policy, National Environmental Policy Act (NEPA) values have been incorporated into the CERCLA process. That is, the analysis conducted and presented in the RVFS reports included an evaluation of environmental impacts that is comparable to that performed under NEPA. This Proposed Plan summarizes information about chemical plant area groundwater that is presented in the following documents: (1) The Remedial Investigation (RI), which presents information on the nature and extent of contamination; (2) The Baseline Risk Assessment (BRA), which evaluates impacts to human health and the environment that could occur if no cleanup action of the groundwater were taken (DOE and DA 1997a); and (3) The Feasibility Study (FS) and the Supplemental FS, which develop and evaluate remedial action alternatives for groundwater remediation

A preliminary survey of radon concentrations in South Island hot springs

International Nuclear Information System (INIS)

Whitehead, N.E.

1976-02-01

Radon 222 was determined in hot spring waters from the South Island of New Zealand by a method involving the radiochemical isolation of 214 Bi. The results ranged from 137 to 1830 pCi/l with a mean of 738 pCi/l. These results are lower than those reported in the literature for North Island hot springs. (auth.)

How Reflected Wave Fronts Dynamically Establish Hooke's Law in a Spring

Science.gov (United States)

Fahy, Stephen; O'Riordan, John; O'Sullivan, Colm; Twomey, Patrick

2012-01-01

A simple benchtop experiment in which a moving cart collides with a fixed spring is described. Force-time and force-distance data recorded during the collision display the transit of compression wave fronts through the spring following impact. These data can be used by students to develop a computational model of the dynamics of this simple…

Failure analysis of top nozzle holddown spring screw for nuclear fuel assembly

International Nuclear Information System (INIS)

Koh, S. K.; Ryu, C. H.; Na, E. G.; Baek, T. H.; Jeon, K. L.

2003-01-01

A failure analysis of holddown spring screw was performed using fracture mechanics approach. The spring screw was designed such that it was capable of sustaining the loads imposed by the initial tensile preload and operational loads. In order to investigate the cause of failure, a stress analysis of the top nozzle spring assembly was done using finite element analysis and a life prediction of the screw was made using a fracture mechanics approach. The elastic-plastic finite element analysis showed that the local stresses at the critical regions of head-shank fillet and thread root significantly exceeded than the yield strength of the screw material, resulting in local plastic deformation. Primary water stress corrosion cracking life of the Inconel 600 screw was predicted by using integration of the Scott model and resulted in 1.42 years, which was fairly close to the actual service life of the holddown spring screw

Diversity and richness of benthic insects in three cold desert spring-streams

Energy Technology Data Exchange (ETDEWEB)

Gaines, W.L.; Cushing, C.E. [Pacific Northwest Lab., Richland, WA (United States)

1993-05-01

The authors examined species diversity and richness in three cold desert spring-streams, and showed that species diversity was similar and species richness was lower than in similar-size streams from other and or semi-arid regions. Species diversity in the spring-streams increased with increasing stream size and substratum diversity, but declined as distance increased from the nearest large source. However, this latter relationship is difficult to quantify because the nearest large source was the Columbia River, or one of its reservoirs, that has environmental conditions very different from those found in the study streams. It is more likely that the main source of colonizers for the spring-streams studied were other nearby small springs that could provide sources or stepping stone habitats for colonizers. Species diversity declined after winter spates, and the low species diversity and richness values appear to be greatly influenced by these events.

A search for correlation between seismicity and radon anomaly in hot springs

International Nuclear Information System (INIS)

Amin, B.S.; Rama

1982-01-01

Measurements of radon contents of the exholved gas emanating from several hot water springs along the Western Coast of India are reported here. Concentration of radon in gas phase of individual sprinqs varied in general, directly with the surface temperature of the water emerging from the respective springs, and showed little variation with time. Radon measurements were carried out continuously for about two years at two hot springs located at Ganeshpuri and Sathivali in the coastal area of Northern Maharashtra. The distant tremors did not cause any variation in the radon content. There was no marked local seismic activity during the period of observations, and the levels of radon stayed essentially constant. The measurements were also carried out at a hot spring in Assam, for about 8 months. These also did not show any significant variation; this period too lacked any marked local seismicity. (author)

Stream flow regime of springs in the Mantiqueira Mountain Range region, Minas Gerais State

Directory of Open Access Journals (Sweden)

Alisson Souza de Oliveira

2014-09-01

Full Text Available The stream flow regime of four springs located in the Mantiqueira Mountain Range region (MG was evaluated and correlated to the respective recharge area, relief characteristics, land cover and physical and hydrologic soil characteristics. The streamflow regime was characterized by monitoring of discharges, calculating the surface runoff and specific discharge and by modeling the discharge over the recession period using the Maillet method. As all recharge areas have similar relief the effect of it on the streamflow was not possible to identify. Analysis included determining the effect of drainage area size, soil characteristics and land cover on the indicators of the streamflow regime. Size of the recharge area had a positive influence on the indicators mean discharge and surface runoff volume and on the regulation of the streamflow regime (springs L4 and L1. The spring under the smallest area of influence provided the worst results for the above mentioned indicators (spring L3. The effect of forest cover (natural and planted, associated with soil characteristics, was evidenced by the indicators surface runoff (in depth and specific yield, both independent of the recharge area size (springs L4 and L2. The interaction of area size, soil characteristics and forest cover (natural and planted provided the best results for all indicators of streamflow regime in the springs studied in the Mantiqueira Mountain Range (spring L4.

Garter spring location of pressure tube for PHWR using eddy current testing methods

International Nuclear Information System (INIS)

Lee, Y. S.; Yang, D. J.; Jeong, H. K.

2001-01-01

There are garter springs between pressure tube and calandria tube for PHWR. If the space of these garter springs become to be changed, the sagging of tube is caused and the contact between the pressure tube and calandria tube will cause the tube to be failed. AECL has applied the eddy current testing methods using send-receive type probe for this purpose, but this study apply eddy current testing methods using bobbin differential type probe to detection of garter spring location. And we did the computer simulation using VIC-3D code and compared it with experiments results for inspection 1 ∼ 11kHz. The results was that the garter spring signal was successfully detected for every frequency, and 5 kHz was best

Spring onset variations and long-term trends from new hemispheric-scale products and remote sensing

Science.gov (United States)

Dye, D. G.; Li, X.; Ault, T.; Zurita-Milla, R.; Schwartz, M. D.

2015-12-01

Spring onset is commonly characterized by plant phenophase changes among a variety of biophysical transitions and has important implications for natural and man-managed ecosystems. Here, we present a new integrated analysis of variability in gridded Northern Hemisphere spring onset metrics. We developed a set of hemispheric temperature-based spring indices spanning 1920-2013. As these were derived solely from meteorological data, they are used as a benchmark for isolating the climate system's role in modulating spring "green up" estimated from the annual cycle of normalized difference vegetation index (NDVI). Spatial patterns of interannual variations, teleconnections, and long-term trends were also analyzed in all metrics. At mid-to-high latitudes, all indices exhibit larger variability at interannual to decadal time scales than at spatial scales of a few kilometers. Trends of spring onset vary across space and time. However, compared to long-term trend, interannual to decadal variability generally accounts for a larger portion of the total variance in spring onset timing. Therefore, spring onset trends identified from short existing records may be aliased by decadal climate variations due to their limited temporal depth, even when these records span the entire satellite era. Based on our findings, we also demonstrated that our indices have skill in representing ecosystem-level spring phenology and may have important implications in understanding relationships between phenology, atmosphere dynamics and climate variability.

Climatic anomalies in the Spring of 2017 in Oltenia.

Directory of Open Access Journals (Sweden)

OCTAVIA BOGDAN

2017-10-01

Full Text Available The year 2015, according to the global average, was the warmest year since the beginning of the measurements and coincided with the maximum phase of the El Nino climatic process that extended until May 2016 (NOAA and WMO documents. A period of normality for the Southern Oscillation followed. In 2015, the global average air temperature exceeded the global average from the pre-industrial age for the first time by 1.0°C. Global warming continued, and 2016 was the warmest year in the history of the planet, exceeding the global average by 1.1°C. In Oltenia, the winter 2016-2017 was normal, with a general average of -1.4°C for the area with altitudes below 600 m, although December 2016 was also thermally normal. The winter was marked by a normal thermally and droughty December and a cold January, with the average for the entire region of -5.07°C, being the fifth coldest January of the last 57 years. In February, the weather continuously warmed up, from February 2nd, the period February 21-28 registering moderate heat wave. The coming of spring was very early, with an average coming of spring index for 2017 of 464.4°C, being the third index in descending order after 2016 (520.3°C and 2002 (499.4°C. Although solar activity has been kept to a minimum, warming has continued, and March has been warm, April and May with a normal thermal value at the regional level. The vegetation started its development early, and the cold weather and late spring hoarfrost occurred in March (27-28.III and April (21-24.IV, which caused significant damage to agricultural crops, vegetables and solariums. In some parts of the country, snow has fallen into certain periods. Early coming of spring, and intense and late spring colds are climatic anomalies with destructive potential as in the present case.

Effect of segregations on mechanical properties and crack propagation in spring steel

Directory of Open Access Journals (Sweden)

B. Žužek

2015-10-01

Full Text Available Considerable efforts have been made over the last decades to improve performance of spring steels, which would increase the service time of springs and also allow vehicles weight reduction. There are different possibilities of improving properties of spring steels, from modifying the chemical composition of steels to optimizing the deformation process and changing the heat treatment parameters. Another way of improving steel properties is through refining the microstructure and reducing amount of inclusions. Therefore, the focus of the current investigation was to determine the effect of more uniform and cleaner microstructure obtained through electro-slag remelting (ESR of steel on the mechanical and dynamic properties of spring steel, with special focus on the resistance to fatigue crack propagation. Effect of the microstructure refinement was evaluated in terms of tensile strength, elongation, fracture and impact toughness, and fatigue resistance under bending and tensile loading. After the mechanical tests the fracture surfaces of samples were analyzed using scanning electron microscope (SEM and the influence of microstructure properties on the crack propagation and crack propagation resistance was studied. Investigation was performed on hot rolled, soft annealed and vacuum heat treated 51CrV4 spring steel produced by conventional continuous casting and compared with steel additional refined through ESR. Results shows that elimination of segregations and microstructure refinement using additional ESR process gives some improvement in terms of better repeatability and reduced scattering, but on the other hand it has negative effect on crack propagation resistance and fatigue properties of the spring steel.

Relation between flow and temporal variations of nitrate and pesticides in two karst springs in northern Alabama

Science.gov (United States)

Kingsbury, J.A.

2008-01-01

Two karst springs in the Mississippian Carbonate Aquifer of northern Alabama were sampled between March 1999 and March 2001 to characterize the variability in concentration of nitrate, pesticides, selected pesticide degradates, water temperature, and inorganic constituents. Water temperature and inorganic ion data for McGeehee Spring indicate that this spring represents a shallow flow system with a relatively short average ground-water residence time. Water issuing from the larger of the two springs, Meridianville Spring, maintained a constant temperature, and inorganic ion data indicate that this water represents a deeper flow system having a longer average ground-water residence time than McGeehee Spring. Although water-quality data indicate differing short-term responses to rainfall at the two springs, the seasonal variation of nitrate and pesticide concentrations generally is similar for the two springs. With the exception of pesticides detected at low concentrations, the coefficient of variation for most constituent concentrations was less than that of flow at both springs, with greater variability in concentration at McGeehee Spring. Degradates of the herbicides atrazine and fluometuron were detected at concentrations comparable to or greater than the parent pesticides. Decreases in concentration of the principal degradate of fluometuron from about July to November indicate that the degradation rate may decrease as fluometuron (demethylfluometuron) moves deeper into the soil after application. Data collected during the study show that from about November to March when recharge rates increase, nitrate and residual pesticides in the soil, unsaturated zone, and storage within the aquifer are transported to the spring discharges. Because of the increase in recharge, fluometuron loads discharged from the springs during the winter were comparable to loads discharged at the springs during the growing season. ?? 2008 American Water Resources Association.

Nitrate concentration in spring water at the Nogawa basin and its possible source

International Nuclear Information System (INIS)

Yoshida, Kazuhiro; Ogura, Norio

1978-01-01

Fluctuation of nitrate concentration in spring water at the Nogawa basin was studied during 1976 - 1977, and the possible source of nitrate nitrogen was discussed. Nitrate concentration in spring water at the station N-O in Kokubunji, Tokyo ranged from 360 to 574 μg at/l with an average value of 502 μg at/l. It seemed that the effluent of spring water at N-O was influenced by rainfall within a short period. A laboratory experiment on production of nitrate in soil showed that ammonium nitrogen added to fresh soil was transformed quantitatively to nitrate nitrogen during 23 days incubation. Thd sup(delta15)N value of nitrate nitrogen in spring water (+0.89%) was similar to that of ammonium nitrogen in sewage (+0.82%) discharging into the Nogawa River. In the area near N-O, domestic wastes have been discharged into the Nogawa River by simple sewers or percolated downward through the soil. These results suggest that one of the main source of nitrate nitrogen in spring water is ammonium and organic nitrogen in domestic wastes. (author)

Effects of spring conditions on breeding propensity of Greater Snow Goose females

Directory of Open Access Journals (Sweden)

Reed, E. T.

2004-06-01

Full Text Available Breeding propensity, defined as the probability that a sexually mature adult will breed in a given year, is an important determinant of annual productivity. It is also one of the least known demographic parameters in vertebrates. We studied the relationship between breeding propensity and conditions on spring staging areas (a spring conservation hunt and the breeding grounds (spring snow cover in Greater Snow Geese (Chen caerulescens atlantica, a long distance migrant that breeds in the High Arctic. We combined information from mark–recapture, telemetry, and nest survey data to estimate breeding propensity over a 7– year period. True temporal variation in breeding propensity was considerable (mean: 0.574 [95% CI considering only process variation: 0.13 to 1.0]. Spring snow cover was negatively related to breeding propensity (bsnow=-2,05 ± 0,96 SE and tended to be reduced in years with a spring hunt (b = -0,78 ± 0,35. Nest densities on the breeding colony and fall ratios of young:adults were good indices of annual variation in breeding propensity, with nest densities being slightly more precise. These results suggest that conditions encountered during the pre-breeding period can have a significant impact on productivity of Arctic-nesting birds

Diagenetic Changes in Common Hot Spring Microfacies

Science.gov (United States)

Hinman, N. W.; Kendall, T. A.; MacKenzie, L. A.; Cady, S. D.

2016-05-01

The friable nature of silica hot spring deposits makes them susceptible to mechanical weathering. Rapid diagenesis must take place for these rocks to persist in the geologic record. The properties of two microfacies at two deposits were compared.

Spot-Welding Gun With Adjustable Pneumatic Spring

Science.gov (United States)

Burley, Richard K.

1990-01-01

Proposed spot-welding gun equipped with pneumatic spring, which could be bellows or piston and cylinder, exerts force independent of position along stroke. Applies accurate controlled force to joint welded, without precise positioning at critical position within stroke.

Geology and hydrology between Lake McMillan and Carlsbad Springs, Eddy County, New Mexico

Science.gov (United States)

Cox, Edward Riley

1967-01-01

The hydrology of the Pecos River valley between Lake McMillan and Carlsbad Springs, Eddy County, N. Mex., is influenced by facies changes in rocks of Permian age. Water stored for irrigation leaks from Lake McMillan into evaporite rocks, principally gypsum, of the Seven Rivers Formation and from Lake Avalon into carbonate rocks of the Tansill Formation. This leakage returns to the Pecos River at Major Johnson Springs and Carlsbad Springs. The river has perennial flow between Major Johnson Springs and Lake Avalon, but it loses water into evaporite rocks of the Yates Formation in this reach. Ground-water movement is generally toward the Pecos River in aquifers in the Pecos River valley except in the Rustler Formation east of the river where it moves southeastward toward playas east of Lake Avalon. The chloride content of ground and surface waters indicates that surface water moves from some reaches of the Pecos River and from surface-storage reservoirs to aquifers and also indicates the degree of mixing of ground and surface waters. About 45,000 acre-feet of ground water is stored in highly permeable rocks in a 3-mile wide part of the Seven Rivers Formation between Lake McMillan and Major Johnson Springs. This water in storage comes from leakage from Lake McMillan and from alluvium north of the springs. The flow of Major Johnson Springs is derived from this aquifer. That part of the flow derived from the alluvium north of the springs averaged 13 cfs (cubic feet per second) from 1953 through 1959 ; about 8 cfs of this flow had not been previously measured at gaging stations on the Pecos River and its tributaries. The most favorable plans for increasing terminal storage of the Carlsbad Irrigation District are to construct a dam at the Brantley site (at the downstream end of Major Johnson Springs), or to use underground storage in the permeable Seven Rivers Formation between Lake McMillan and Major Johnson brings in conjunction with surface storage. To avoid excessive

Sources of nitrate contamination and age of water in large karstic springs of Florida

Science.gov (United States)

Katz, B.G.

2004-01-01

In response to concerns about the steady increase in nitrate concentrations over the past several decades in many of Florida's first magnitude spring waters (discharge ???2.8 m3/s), multiple isotopic and other chemical tracers were analyzed in water samples from 12 large springs to assess sources and timescales of nitrate contamination. Nitrate-N concentrations in spring waters ranged from 0.50 to 4.2 mg/L, and ??15N values of nitrate in spring waters ranged from 2.6 to 7.9 per mil. Most ??15N values were below 6 per mil indicating that inorganic fertilizers were the dominant source of nitrogen in these waters. Apparent ages of groundwater discharging from springs ranged from 5 to about 35 years, based on multi-tracer analyses (CFC-12, CFC-113, SF6, 3H/3He) and a piston flow assumption; however, apparent tracer ages generally were not concordant. The most reliable spring-water ages appear to be based on tritium and 3He data, because concentrations of CFCs and SF6 in several spring waters were much higher than would be expected from equilibration with modern atmospheric concentrations. Data for all tracers were most consistent with output curves for exponential and binary mixing models that represent mixtures of water in the Upper Floridan aquifer recharged since the early 1960s. Given that groundwater transit times are on the order of decades and are related to the prolonged input of nitrogen from multiple sources to the aquifer, nitrate could persist in groundwater that flows toward springs for several decades due to slow transport of solutes through the aquifer matrix.

Axial-flow-induced vibration for a rod supported by translational springs at both ends

International Nuclear Information System (INIS)

Kang, H.S.; Song, K.N.; Kim, H.K.; Yoon, K.H.

2003-01-01

An axial-flow-induced vibration model was proposed for a rod supported by two translational springs at both ends in order to evaluate the sensitivity to spring stiffness on the FIV for a PWR fuel rod. For developing the model, a one-mode approximation was made based on the assumption that the first mode was dominant in vibration behavior of the single span rod. The first natural frequency and mode shape functions for the flow-induced vibration, called the FIV, model were derived by using Lagrange's method. The vibration displacements were calculated by both of the spring-supported rod and the simple-supported (SS) one. As a result, the vibration displacement for the spring-supported (50 kN m -1 ) rod was 15-20% larger than that of the SS rod when the rods are in axial flow of 5-8 m s -1 velocity. The discrepancy between both displacements became much larger as flow velocity increased, and that of the rod having the short span length was larger than that of the rod having the long span length although the displacement value itself of the long span rod was larger than that of the short one. The vibration displacement for the spring-supported rod appeared to decrease with the increase of the spring constant. Since single span beam supported by the two translational springs are focused on in this paper, further study will be needed to reflect more realistic supporting conditions of the PWR fuel rod such as two springs and four dimples and cross or swirling flow caused by the mixing vane of the spacer grid

Effect of source integration on the geochemical fluxes from springs

International Nuclear Information System (INIS)

Frisbee, Marty D.; Phillips, Fred M.; White, Art F.; Campbell, Andrew R.; Liu, Fengjing

2013-01-01

Geochemical fluxes from watersheds are typically defined using mass-balance methods that essentially lump all weathering processes operative in a watershed into a single flux of solute mass measured in streamflow at the watershed outlet. However, it is important that we understand how weathering processes in different hydrological zones of a watershed (i.e., surface, unsaturated, and saturated zones) contribute to the total geochemical flux from the watershed. This capability will improve understanding of how geochemical fluxes from these different zones may change in response to climate change. Here, the geochemical flux from weathering processes occurring solely in the saturated zone is investigated. This task, however, remains exceedingly difficult due to the sparsity of subsurface sampling points, especially in large, remote, and/or undeveloped watersheds. In such cases, springflow is often assumed to be a proxy for groundwater (defined as water residing in fully saturated geologic formations). However, springflow generation may integrate different sources of water including, but not limited to, groundwater. The authors’ hypothesis is that long-term estimates of geochemical fluxes from groundwater using springflow proxies will be too large due to the integrative nature of springflow generation. Two conceptual models of springflow generation are tested using endmember mixing analyses (EMMA) on observations of spring chemistries and stable isotopic compositions in a large alpine watershed in the San Juan Mountains of southwestern Colorado. In the “total springflow” conceptual model, springflow is assumed to be 100% groundwater. In the “fractional springflow” conceptual model, springflow is assumed to be an integration of different sources of water (e.g., groundwater, unsaturated flow, preferential flow in the soil, etc.) and groundwater is only a fractional component. The results indicate that groundwater contributions in springflow range from 2% to 100

Comparative Metagenomics of Eight Geographically Remote Terrestrial Hot Springs.

Science.gov (United States)

Menzel, Peter; Gudbergsdóttir, Sóley Ruth; Rike, Anne Gunn; Lin, Lianbing; Zhang, Qi; Contursi, Patrizia; Moracci, Marco; Kristjansson, Jakob K; Bolduc, Benjamin; Gavrilov, Sergey; Ravin, Nikolai; Mardanov, Andrey; Bonch-Osmolovskaya, Elizaveta; Young, Mark; Krogh, Anders; Peng, Xu

2015-08-01

Hot springs are natural habitats for thermophilic Archaea and Bacteria. In this paper, we present the metagenomic analysis of eight globally distributed terrestrial hot springs from China, Iceland, Italy, Russia, and the USA with a temperature range between 61 and 92 (∘)C and pH between 1.8 and 7. A comparison of the biodiversity and community composition generally showed a decrease in biodiversity with increasing temperature and decreasing pH. Another important factor shaping microbial diversity of the studied sites was the abundance of organic substrates. Several species of the Crenarchaeal order Thermoprotei were detected, whereas no single bacterial species was found in all samples, suggesting a better adaptation of certain archaeal species to different thermophilic environments. Two hot springs show high abundance of Acidithiobacillus, supporting the idea of a true thermophilic Acidithiobacillus species that can thrive in hyperthermophilic environments. Depending on the sample, up to 58 % of sequencing reads could not be assigned to a known phylum, reinforcing the fact that a large number of microorganisms in nature, including those thriving in hot environments remain to be isolated and characterized.

Nuclear fuel rod grip with modified diagonal spring structures

International Nuclear Information System (INIS)

DeMario, E.E.

1990-01-01