WorldWideScience

Sample records for pins melting facility

  1. Impregnation of a glass fibre roving with a polypropylene melt in a pin assisted process

    NARCIS (Netherlands)

    Gaymans, R.J.; Wevers, E.

    1998-01-01

    The impregnation of a glass fibre bundle with a polypropylene (PP) melt is studied with a pin assisted process. A fibre is pulled over a pin, which is positioned in a chamber filled with a melt. The melt is at atmospheric pressure. The impregnation rate is studied as a function of size of the pin,

  2. HLM fuel pin bundle experiments in the CIRCE pool facility

    Energy Technology Data Exchange (ETDEWEB)

    Martelli, Daniele, E-mail: daniele.martelli@ing.unipi.it [University of Pisa, Department of Civil and Industrial Engineering, Pisa (Italy); Forgione, Nicola [University of Pisa, Department of Civil and Industrial Engineering, Pisa (Italy); Di Piazza, Ivan; Tarantino, Mariano [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone (Italy)

    2015-10-15

    Highlights: • The experimental results represent the first set of values for LBE pool facility. • Heat transfer is investigated for a 37-pin electrical bundle cooled by LBE. • Experimental data are presented together with a detailed error analysis. • Nu is computed as a function of the Pe and compared with correlations. • Experimental Nu is about 25% lower than Nu derived from correlations. - Abstract: Since Lead-cooled Fast Reactors (LFR) have been conceptualized in the frame of GEN IV International Forum (GIF), great interest has focused on the development and testing of new technologies related to HLM nuclear reactors. In this frame the Integral Circulation Experiment (ICE) test section has been installed into the CIRCE pool facility and suitable experiments have been carried out aiming to fully investigate the heat transfer phenomena in grid spaced fuel pin bundles providing experimental data in support of European fast reactor development. In particular, the fuel pin bundle simulator (FPS) cooled by lead bismuth eutectic (LBE), has been conceived with a thermal power of about 1 MW and a uniform linear power up to 25 kW/m, relevant values for a LFR. It consists of 37 fuel pins (electrically simulated) placed on a hexagonal lattice with a pitch to diameter ratio of 1.8. The FPS was deeply instrumented by several thermocouples. In particular, two sections of the FPS were instrumented in order to evaluate the heat transfer coefficient along the bundle as well as the cladding temperature in different ranks of sub-channels. Nusselt number in the central sub-channel was therefore calculated as a function of the Peclet number and the obtained results were compared to Nusselt numbers obtained from convective heat transfer correlations available in literature on Heavy Liquid Metals (HLM). Results reported in the present work, represent the first set of experimental data concerning fuel pin bundle behaviour in a heavy liquid metal pool, both in forced and

  3. Flux pinning effect in a melt textured YBCO bulk evaluated by using tension measurements

    Science.gov (United States)

    Lee, Joon Ho; Ahmad, Dawood; Kim, Byoung Joo; Cha, Myoungsik; Yang, Ho Soon; Kim, Young Cheol; Ko, Rock Kil; Jeong, Dae Young

    2013-01-01

    Research on the flux pinning effect in type-II superconductors has usually been focused on microor nanosize pinning centers, and mm-sized pinning centers have been relatively less studied. In order to investigate the flux pinning effect caused by mm-sized pinning centers, we introduce a tension measurement method in this research. A cm-sized melt-textured YBCO bulk, in which holes with a 2 mm diameter are made, is prepared. The YBCO bulk is field-cooled by using a strong magnet in liquid nitrogen, and the bulk and the magnet are separated from each other. Then, an attractive force ( f a ) between them is generated, and f a is detected by using a tension measuring device. As the distance ( d) between them is increased, f a increases at short distance and decreases at long distance, showing a maximum value, f am , at a specific distance. The measurement of f a is stopped when d reaches a value defined as the breaking distance ( d bk ), as if a `string' between the magnet and the YBCO bulk is broken. As the number of holes ( n) made in the YBCO bulk increases from 1 to 6, f am and d bk increase, in spite of the superconducting volume loss. f am and d bk for n ≥ 7 converge to nearly constant values, which are smaller than the values for n = 6. This means that the critical current density can be calculated by using f am or d bk for a sufficient number of holes.

  4. Glass Furnace Combustion and Melting Research Facility.

    Energy Technology Data Exchange (ETDEWEB)

    Connors, John J. (PPG Industries, Inc., Pittsburgh, PA); McConnell, John F. (JFM Consulting, Inc., Pittsburgh, PA); Henry, Vincent I. (Henry Technology Solutions, LLC, Ann Arbor, MI); MacDonald, Blake A.; Gallagher, Robert J.; Field, William B. (Lilja Corp., Livermore, CA); Walsh, Peter M.; Simmons, Michael C. (Lilja Corp., Livermore, CA); Adams, Michael E. (Lilja Corp., Rochester, NY); Leadbetter, James M. (A.C. Leadbetter and Son, Inc., Toledo, OH); Tomasewski, Jack W. (A.C. Leadbetter and Son, Inc., Toledo, OH); Operacz, Walter J. (A.C. Leadbetter and Son, Inc., Toledo, OH); Houf, William G.; Davis, James W. (A.C. Leadbetter and Son, Inc., Toledo, OH); Marvin, Bart G. (A.C. Leadbetter and Son, Inc., Toledo, OH); Gunner, Bruce E. (A.C. Leadbetter and Son, Inc., Toledo, OH); Farrell, Rick G. (A.C. Leadbetter and Son, Inc., Toledo, OH); Bivins, David P. (PPG Industries, Inc., Pittsburgh, PA); Curtis, Warren (PPG Industries, Inc., Pittsburgh, PA); Harris, James E. (PPG Industries, Inc., Pittsburgh, PA)

    2004-08-01

    The need for a Combustion and Melting Research Facility focused on the solution of glass manufacturing problems common to all segments of the glass industry was given high priority in the earliest version of the Glass Industry Technology Roadmap (Eisenhauer et al., 1997). Visteon Glass Systems and, later, PPG Industries proposed to meet this requirement, in partnership with the DOE/OIT Glass Program and Sandia National Laboratories, by designing and building a research furnace equipped with state-of-the-art diagnostics in the DOE Combustion Research Facility located at the Sandia site in Livermore, CA. Input on the configuration and objectives of the facility was sought from the entire industry by a variety of routes: (1) through a survey distributed to industry leaders by GMIC, (2) by conducting an open workshop following the OIT Glass Industry Project Review in September 1999, (3) from discussions with numerous glass engineers, scientists, and executives, and (4) during visits to glass manufacturing plants and research centers. The recommendations from industry were that the melting tank be made large enough to reproduce the essential processes and features of industrial furnaces yet flexible enough to be operated in as many as possible of the configurations found in industry as well as in ways never before attempted in practice. Realization of these objectives, while still providing access to the glass bath and combustion space for optical diagnostics and measurements using conventional probes, was the principal challenge in the development of the tank furnace design. The present report describes a facility having the requirements identified as important by members of the glass industry and equipped to do the work that the industry recommended should be the focus of research. The intent is that the laboratory would be available to U.S. glass manufacturers for collaboration with Sandia scientists and engineers on both precompetitive basic research and the

  5. Los Alamos Hot-Cell-Facility modifications for examining FFTF fuel pins

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, B.M.; Ledbetter, J.M.

    1982-01-01

    Commissioned in 1960, the Wing 9 Hot Cell Facility at Los Alamos was recently modified to meet the needs of the 1980s. Because fuel pins from the Fast Flux Test Facility (FFTF) at the Hanford Engineering Development Laboratory (HEDL) are too long for examination in the original hot cells, we modified cells to accommodate longer fuel pins and to provide other capabilities as well. For instance, the T-3 shipping cask now can be opened in an inert atmosphere that can be maintained for all nondestructive and destructive examinations of the fuel pins. The full-length pins are visually examined and photographed, the wire wrap is removed, and fission gas is sampled. After the fuel pin is cropped, a cap is seal-welded on the section containing the fuel column. This section is then transferred to other cells for gamma-scanning, radiography, profilometry, sectioning for metallography, and chemical analysis.

  6. Sodium Loop Safety Facility W-2 experiment fuel pin rupture detection system. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, M.A.; Kirchner, T.L.; Meyers, S.C.

    1980-05-01

    The objective of the Sodium Loop Safety Facility (SLSF) W-2 experiment is to characterize the combined effects of a preconditioned full-length fuel column and slow transient overpower (TOP) conditions on breeder reactor (BR) fuel pin cladding failures. The W-2 experiment will meet this objective by providing data in two technological areas: (1) time and location of cladding failure, and (2) early post-failure test fuel behavior. The test involves a seven pin, prototypic full-length fast test reactor (FTR) fuel pin bundle which will be subjected to a simulated unprotected 5 cents/s reactivity transient overpower event. The outer six pins will provide the necessary prototypic thermal-hydraulic environment for the center pin.

  7. Geometrical vortex lattice pinning and melting in YBaCuO submicron bridges

    Science.gov (United States)

    Papari, G. P.; Glatz, A.; Carillo, F.; Stornaiuolo, D.; Massarotti, D.; Rouco, V.; Longobardi, L.; Beltram, F.; Vinokur, V. M.; Tafuri, F.

    2016-12-01

    Since the discovery of high-temperature superconductors (HTSs), most efforts of researchers have been focused on the fabrication of superconducting devices capable of immobilizing vortices, hence of operating at enhanced temperatures and magnetic fields. Recent findings that geometric restrictions may induce self-arresting hypervortices recovering the dissipation-free state at high fields and temperatures made superconducting strips a mainstream of superconductivity studies. Here we report on the geometrical melting of the vortex lattice in a wide YBCO submicron bridge preceded by magnetoresistance (MR) oscillations fingerprinting the underlying regular vortex structure. Combined magnetoresistance measurements and numerical simulations unambiguously relate the resistance oscillations to the penetration of vortex rows with intermediate geometrical pinning and uncover the details of geometrical melting. Our findings offer a reliable and reproducible pathway for controlling vortices in geometrically restricted nanodevices and introduce a novel technique of geometrical spectroscopy, inferring detailed information of the structure of the vortex system through a combined use of MR curves and large-scale simulations.

  8. Tungsten and molybdenum double perovskites as pinning centers in melt-textured Y123

    Energy Technology Data Exchange (ETDEWEB)

    Sawh, Ravi-Persad; Weinstein, Roy; Parks, Drew; Gandini, Alberto; Ren, Yanru; Rusakova, Irene

    2003-01-01

    Y123+30 mol% Y211 powders were doped with tungsten and platinum, and textured. Microstructure studies show the presence of profuse spherical deposits, 200-300 nm in diameter. These deposits were identified as (W{sub 0.5}Pt{sub 0.5})YBa{sub 2}O{sub 6}, a double perovskite. The size of the W-rich deposits is independent of the W doping level. There is no substitution of W into the Y123 matrix. For Pt doping >0.5 wt.%, trapped field is observed to increase monotonically up to 40% for W doping of up to 0.48 wt.%. We conservatively estimate that this corresponds to a 60% increase in J{sub c} at constant field. Thus (W{sub 0.5}Pt{sub 0.5})YBa{sub 2}O{sub 6} double perovskites deposits act as pinning centers. Similar studies of molybdenum doping indicate deposits 200-300 nm, of (Mo{sub 0.5}Pt{sub 0.5})YBa{sub 2}O{sub 6}, also a double perovskite. The (W{sub 0.5}Pt{sub 0.5})YBa{sub 2}O{sub 6} and (Mo{sub 0.5}Pt{sub 0.5})YBa{sub 2}O{sub 6} deposits are remarkably similar to the (U{sub 0.6}Pt{sub 0.4})YBa{sub 2}O{sub 6} deposits found earlier in U-doped Y123. Therefore, W and Mo are suitable non-radioactive substitutes for U.

  9. Thermal performances and melting risk assessment in a LMFBR fuel pin

    Science.gov (United States)

    Vettraino, F.; Cacciabue, P. C.; Brunelli, F.

    1985-02-01

    A reliable evaluation of fuel temperature is a key safety requirement in the design of the fuel assembly of a nuclear reactor, especially in the case of a LMFBR whose efficient operation requires high thermal performance fuel. The physico-chemical properties such as density, oxygen to metal ratio and thermal conductivity of a typical LMFBR mixed-oxide fuel, which are known to change in a remarkable way under irradiation, strongly affect the temperature profile within the fuel pellet. A statistical analysis of the temperature values in the fuel of the Italian Fast Reactor PEC, has been performed by means of the RSM code (Response Surface Methodology) coupled to a Monte-Carlo Technique (MUP code), in order to demonstrate that the melting risk is substantially negligible.

  10. Large levitation force due to flux pinning in YBaCuO superconductors fabricated by Melt-Powder-Melt-Growth process

    Science.gov (United States)

    Murakami, Masato; Oyama, Terutugu; Fujimoto, Hiroyuki; Taguchi, Takahiro; Gotoh, Satoshi

    1990-11-01

    An extremely large levitation force of as high as 30 N at a height of 1 mm was achieved in Ag-doped YBaCuO fabricated by the Melt-Powder-Melt-Growth process using a repulsive force against a 0.4 T rare-earth magnet at 77 K. The combination of a large Jc value and large shielding current loop is the source of such a large levitation force.

  11. Heat transfer on HLM cooled wire-spaced fuel pin bundle simulator in the NACIE-UP facility

    Energy Technology Data Exchange (ETDEWEB)

    Di Piazza, Ivan, E-mail: ivan.dipiazza@enea.it [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone, Camugnano (Italy); Angelucci, Morena; Marinari, Ranieri [University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Pisa (Italy); Tarantino, Mariano [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone, Camugnano (Italy); Forgione, Nicola [University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Pisa (Italy)

    2016-04-15

    Highlights: • Experiments with a wire-wrapped 19-pin fuel bundle cooled by LBE. • Wall and bulk temperature measurements at three axial positions. • Heat transfer and error analysis in the range of low mass flow rates and Péclet number. • Comparison of local and section-averaged Nusselt number with correlations. - Abstract: The NACIE-UP experimental facility at the ENEA Brasimone Research Centre (Italy) allowed to evaluate the heat transfer coefficient of a wire-spaced fuel bundle cooled by lead-bismuth eutectic (LBE). Lead or lead-bismuth eutectic are very attractive as coolants for the GEN-IV fast reactors due to the good thermo-physical properties and the capability to fulfil the GEN-IV goals. Nevertheless, few experimental data on heat transfer with heavy liquid metals (HLM) are available in literature. Furthermore, just a few data can be identified on the specific topic of wire-spaced fuel bundle cooled by HLM. Additional analysis on thermo-fluid dynamic behaviour of the HLM inside the subchannels of a rod bundle is necessary to support the design and safety assessment of GEN. IV/ADS reactors. In this context, a wire-spaced 19-pin fuel bundle was installed inside the NACIE-UP facility. The pin bundle is equipped with 67 thermocouples to monitor temperatures and analyse the heat transfer behaviour in different sub-channels and axial positions. The experimental campaign was part of the SEARCH FP7 EU project to support the development of the MYRRHA irradiation facility (SCK-CEN). Natural and mixed circulation flow regimes were investigated, with subchannel Reynolds number in the range Re = 1000–10,000 and heat flux in the range q″ = 50–500 kW/m{sup 2}. Local Nusselt numbers were calculated for five sub-channels in different ranks at three axial positions. Section-averaged Nusselt number was also defined and calculated. Local Nusselt data showed good consistency with some of the correlation existing in literature for heat transfer in liquid metals

  12. Melt dispersion and direct containment heating (DCH) experiments in the DISCO-H test facility

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, L.; Albrecht, G.; Kirstahler, M.; Schwall, M.; Wachter, E.; Woerner, G.

    2004-05-01

    The DISCO-H Test Facility at Forschungszentrum Karlsruhe was set up to perform scaled experiments that simulate melt ejection scenarios under low system pressure in Severe Accidents in Pressurized Water Reactors (PWR). These experiments are designed to investigate the fluid-dynamic, thermal and chemical processes during melt ejection out of a breach in the lower head of a PWR pressure vessel at pressures below 2 MPa with an iron-alumina melt and steam. In the past, a detailed study of pressure and geometry effects on the fluid dynamics of the melt dispersion process had been performed with cold model fluids in the facility DISCO-C. The main components of the facility are scaled about 1:18 linearly to a large European pressurized water reactor. Standard test results are: pressure and temperature history in the RPV, the cavity, the reactor compartment and the containment, post test melt fractions in all locations with size distribution of the debris, video film in reactor compartment and containment (timing of melt flow and hydrogen burning), and pre- and post test gas analysis in the cavity and the containment. The results of six experiments are presented here. All experiments were done with 10.6 kg of iron-alumina melt (scaling to 16 m{sup 3} corium), and a hole of 56 mm diameter (1 m scaled) or 28 mm at the center of the lower head. For comparison with a similar experiment conducted in a larger scale (1:10), the basis experiment was performed with an open path from the reactor pit to the containment (open pit), with prototypical conditions concerning the steam driven ejection out of the RPV, and a containment atmosphere, that was part air and part steam at an elevated pressure, with 3 mole-% hydrogen. In this and other tests, hydrogen production and combustion occurred. In one experiment the hydrogen effect was excluded by using only nitrogen as driving gas and a pure air atmosphere in the containment. In some tests the direct path to the containment was closed

  13. Design, fabrication, and evaluation of a partially melted ice particle cloud facility

    Science.gov (United States)

    Soltis, Jared T.

    High altitude ice crystal clouds created by highly convective storm cells are dangerous to jet transport aircraft because the crystals are ingested into the compressor section, partially melt, accrete, and cause roll back or flame out. Current facilities to test engine particle icing are not ideal for fundamental mixed-phase ice accretion experiments or do not generate frozen droplet clouds under representative conditions. The goal of this research was to develop a novel facility capable of testing fundamental partially melted ice particle icing physics and to collect ice accretion data related to mixed-phase ice accretion. The Penn State Icing Tunnel (PSIT) has been designed and fabricated to conduct partially melted ice particle cloud accretion. The PSIT generated a cloud with air assisted atomizing nozzles. The water droplets cool from the 60psi pressure drop as the water exited the nozzle and fully glaciate while flowing in the -11.0°C tunnel air flow. The glaciated cloud flowed through a duct in the center of the tunnel where hot air was introduced. The temperature of the duct was regulated from 3.3°C to 24°C which melted particle the frozen particle from 0% to 90%. The partially melted particle cloud impinged on a temperature controlled flat plate. Ice accretion data was taken for a range of duct temperature from 3.3°C to 24°C and plate temperature from -4.5°C to 7.0°C. The particle median volumetric diameter was 23mum, the total water content was 4.5 g/m 3, the specific humidity was 1.12g/kg, and the wet bulb temperature ranged from 1.0°C to 7.0°C depending on the duct temperature. The boundaries between ice particle bounce off, ice accretion, and water run off were determined. When the particle were totally frozen and the plate surface was below freezing, the ice particle bounced off as expected. Ice accretion was seen for all percent melts tested, but the plate temperature boundary between water runoff and ice accretion increased from 0°C at 8

  14. High-Resolution Melting Curve Analysis for Identification of Pasteurellaceae Species in Experimental Animal Facilities.

    Science.gov (United States)

    Miller, Manuel; Zorn, Julia; Brielmeier, Markus

    2015-01-01

    Pasteurellaceae are among the most prevalent bacterial pathogens isolated from mice housed in experimental animal facilities. Reliable detection and differentiation of Pasteurellaceae are essential for high-quality health monitoring. In this study, we combined a real-time PCR assay amplifying a variable region in the 16S rRNA sequence with high-resolution melting curve analysis (HRM) to identify and differentiate among the commonly isolated species Pasteurella pneumotropica biotypes "Jawetz" and "Heyl", Actinobacillus muris, and Haemophilus influenzaemurium. We used a set of six reference strains for assay development, with the melting profiles of these strains clearly distinguishable due to DNA sequence variations in the amplicon. For evaluation, we used real-time PCR/HRM to test 25 unknown Pasteurellaceae isolates obtained from an external diagnostic laboratory and found the results to be consistent with those of partial 16S rRNA sequencing. The real-time PCR/HRM method provides a sensitive, rapid, and closed-tube approach for Pasteurellaceae species identification for health monitoring of laboratory mice.

  15. High-Resolution Melting Curve Analysis for Identification of Pasteurellaceae Species in Experimental Animal Facilities.

    Directory of Open Access Journals (Sweden)

    Manuel Miller

    Full Text Available Pasteurellaceae are among the most prevalent bacterial pathogens isolated from mice housed in experimental animal facilities. Reliable detection and differentiation of Pasteurellaceae are essential for high-quality health monitoring. In this study, we combined a real-time PCR assay amplifying a variable region in the 16S rRNA sequence with high-resolution melting curve analysis (HRM to identify and differentiate among the commonly isolated species Pasteurella pneumotropica biotypes "Jawetz" and "Heyl", Actinobacillus muris, and Haemophilus influenzaemurium. We used a set of six reference strains for assay development, with the melting profiles of these strains clearly distinguishable due to DNA sequence variations in the amplicon. For evaluation, we used real-time PCR/HRM to test 25 unknown Pasteurellaceae isolates obtained from an external diagnostic laboratory and found the results to be consistent with those of partial 16S rRNA sequencing. The real-time PCR/HRM method provides a sensitive, rapid, and closed-tube approach for Pasteurellaceae species identification for health monitoring of laboratory mice.

  16. Depth-dependent critical-current density of melt-processed Y-Ba-Cu-O discs determined by the third-harmonic technique: Surface barrier and intrinsic pinning

    Energy Technology Data Exchange (ETDEWEB)

    Chen, D-X, E-mail: duxingchen039@gmail.com [Departament de Física, Universitat Autònoma de Barcelona, 08193 Bellaterra, Barcelona (Spain); He, T-F; Zhang, M-J [School of Instrumentation Science and Opt-Electronics Engineering, Beihang University, Beijing (China); Wang, S-S [School of Physics and Nuclear Energy Engineering, Beihang University, Beijing (China); Shi, Y-H; Cardwell, D A [Engineering Department, University of Cambridge, Trumpington Street, Cambridge CB2 1PZ (United Kingdom)

    2016-08-15

    Highlights: • Third harmonic technique is modified for measuring depth dependent Jc of bulk superconductor. • Surface damage and reduced effect of surface barrier and intrinsic pinning are found in melt-processed YBCO discs. • Experimental findings are explained by existing models. - Abstract: The critical-current density J{sub c} of three Y-Ba-Cu-O (YBCO) discs, each cut from the upper section of a melt-processed single grain, has been determined as a function of the depth from the top (seeded) and bottom surfaces of the sample by a modified version of the inductive third-harmonic technique proposed originally by Mawatari et al. It is shown that local J{sub c} in the vicinity of the bottom surface of the sample is lower than that in the vicinity of the top surface for thicker discs and there are reduced effect of surface barrier and intrinsic pinning and important surface damage. The technique employed is recommended as a tool for detecting the imperfection within superconducting structure in bulk YBCO.

  17. Metallography and fuel cladding chemical interaction in fast flux test facility irradiated metallic U-10Zr MFF-3 and MFF-5 fuel pins

    Science.gov (United States)

    Carmack, W. J.; Chichester, H. M.; Porter, D. L.; Wootan, D. W.

    2016-05-01

    The Mechanistic Fuel Failure (MFF) series of metal fuel irradiations conducted in the Fast Flux Test Facility (FFTF) provides an important comparison between data generated in the Experimental Breeder Reactor (EBR-II) and that expected in a larger-scale fast reactor. The MFF fuel operated with a peak cladding temperature at the top of the fuel column, but developed peak burnup at the centerline of the core. This places the peak fuel temperature midway between the core center and the top of fuel, lower in the fuel column than in EBR-II experiments. Data from the MFF-3 and MFF-5 assemblies are most comparable to the data obtained from the EBR-II X447 experiment. The two X447 pin breaches were strongly influenced by fuel/cladding chemical interaction (FCCI) at the top of the fuel column. Post irradiation examination data from MFF-3 and MFF-5 are presented and compared to historical EBR-II data.

  18. Depth-dependent critical-current density of melt-processed Y-Ba-Cu-O discs determined by the third-harmonic technique: Surface barrier and intrinsic pinning

    Science.gov (United States)

    Chen, D.-X.; He, T.-F.; Zhang, M.-J.; Wang, S.-S.; Shi, Y.-H.; Cardwell, D. A.

    2016-08-01

    The critical-current density Jc of three Y-Ba-Cu-O (YBCO) discs, each cut from the upper section of a melt-processed single grain, has been determined as a function of the depth from the top (seeded) and bottom surfaces of the sample by a modified version of the inductive third-harmonic technique proposed originally by Mawatari et al. It is shown that local Jc in the vicinity of the bottom surface of the sample is lower than that in the vicinity of the top surface for thicker discs and there are reduced effect of surface barrier and intrinsic pinning and important surface damage. The technique employed is recommended as a tool for detecting the imperfection within superconducting structure in bulk YBCO.

  19. Metallography and fuel cladding chemical interaction in fast flux test facility irradiated metallic U-10Zr MFF-3 and MFF-5 fuel pins

    Energy Technology Data Exchange (ETDEWEB)

    Carmack, W. J.; Chichester, H. M.; Porter, D. L.; Wootan, D. W.

    2016-05-01

    Abstract The Mechanistic Fuel Failure (MFF) series of metal fuel irradiations conducted in the Fast Flux Test Facility (FFTF) provides an important potential comparison between data generated in the Experimental Breeder Reactor (EBR-II) and that expected in a larger-scale fast reactor. The irradiations were the beginning tests to qualify U-10wt%Zr as a driver fuel for FFTF. The FFTF core, with a 91.4 cm tall fuel column and a chopped cosine neutron flux profile, operated with a peak cladding temperature at the top of the fuel column, but developed peak burnup at the centerline of the core. This places the peak fuel temperature midway between the core center and the top of fuel, lower in the fuel column than in previous EBR-II experiments that had a 32-cm height core. The MFF-3 and MFF-5 qualification assemblies operated in FFTF to >10 at% burnup, and performed very well with no cladding breaches. The MFF-3 assembly operated to 13.8 at% burnup with a peak inner cladding temperature of 643°C, and the MFF-5 assembly operated to 10.1 at% burnup with a peak inner cladding temperature of 651°C. Because of the very high operating temperatures for both the fuel and the cladding, data from the MFF assemblies are most comparable to the data obtained from the EBR-II X447 experiment, which experienced two pin breaches. The X447 breaches were strongly influenced by a large amount of fuel/cladding chemical interaction (FCCI). The MFF pins benefitted from different axial locations of high burnup and peak cladding temperature, which helped to reduce interdiffusion between rare earth fission products and stainless steel cladding. Post-irradiation examination evidence illustrates this advantage. Comparing other performance data of the long MFF pins to prior EBR-II test data, the MFF fuel inside the cladding grew less axially, and the gas release data did not reveal a definitive difference.

  20. Happy Pinning

    DEFF Research Database (Denmark)

    Fausing, Bent

    2012-01-01

    This is about Pinterest, but with a different approach than usual to social networks. Pinterest is an image site par excellence. The images are as Windows that open outwards and also lets us look inwards and displays the soul and heart, the unintentional or pre-conscious desires. Happy Pinning!...

  1. Happy Pinning

    DEFF Research Database (Denmark)

    Fausing, Bent

    2012-01-01

    This is about Pinterest, but with a different approach than usual to social networks. Pinterest is an image site par excellence. The images are as Windows that open outwards and also lets us look inwards and displays the soul and heart, the unintentional or pre-conscious desires. Happy Pinning!...

  2. Facile synthesis of a melt-spinnable polyborazine from asymmetric alkylaminoborazine

    Institute of Scientific and Technical Information of China (English)

    Yong Peng Lei; Ying De Wang; Yong Cai Song; Yi He Li; Hao Wang; Cheng Deng; Zheng Fang Xie

    2010-01-01

    A novel asymmetric alkylaminoborazine monomer,2-propylamino-4,6-bis(methylamino)borazine,was synthesized for the first time,and directly polymerized to give a melt-spinnable polyborazine(PBN).This asymmetric alkylaminoborazine was synthesized by an aminolysis reaction of 2,4,6-trichloroborazine(TCB)with different amines under mild conditions.This route turns out to be much cheaper and simpler than the conventional routes.The chemical composition,structure,molecular weights and ceramic yield were investigated by EA,FTIR,NMR,GPC and TG analysis.The PBN exhibits suitable rheological property for melt-spinning,which suggests that it is a potential precursor for BN fibers.

  3. Pediatric safety pin ingestion.

    Science.gov (United States)

    Sarihan, H; Kaklikkaya, I; Ozcan, F

    1998-08-01

    Fifteen consecutive children with ingested safety pins were evaluated retrospectively. Eight patients were males and seven were girls. The mean age of the patients was 5.4 years ranging from 7 months to 16 years. Two of 15 patients were mentally retarded Seven safety pins ingestion were noted by parents, three older children applied with safety pin swallowing. Three infants referred with hypersalivation and swallowing difficulty. One of two mentally retarded patients had recurrent aspiration pneumonia, the other had neck abscess. These patients' lesions were detected incidentally by thoracic X-ray. Nine safety pins were at the level of the cricopharyngeus, one at the level of the aortic arch and five at the esophagogastric junction. A right esophagoscopy was used for extraction of safety pins under general anesthesia and endotracheal intubation were used. Before esophagoscopy control plain X-ray was obtained for location of safety pin. Nine safety pins were extracted by esophagoscopy. Three safety pins spontaneously and three during anesthesia induction passed through the esophagus falling down the stomach. Five of these six safety pins were spontaneously extracted without complication. However one open safety pin lodged at the duodenum and laparotomy was required. In this article, etiology and management of safety pin ingestion in children are discussed.

  4. 327 to 324 Pin tube shipment quality management process plan

    Energy Technology Data Exchange (ETDEWEB)

    HAM, J.E.

    1998-11-05

    The B and W Hanford Company's (BWHC) 327 Facility, in the 300 Area of the Hanford Site, is preparing to ship five Pin Tubes to the 324 Facility for storage and eventual disposition. The Pin Tubes consist of legacy fuel pin pieces and drillings. They will be over-packed in new Pin Tubes and transported to 324 in three shipments. Once received at 324, two of the shipments will be combined for storage as a fissionable material batch, and the other shipment will be added to an existing batch.

  5. Integral coolant channels supply made by melt-out method

    Science.gov (United States)

    Escher, W. J. D.

    1964-01-01

    Melt-out method of constructing strong, pressure-tight fluid coolant channels for chambers is accomplished by cementing pins to the surface and by depositing a melt-out material on the surface followed by two layers of epoxy-resin impregnated glass fibers. The structure is heated to melt out the low-melting alloy.

  6. PINS Spectrum Identification Guide

    Energy Technology Data Exchange (ETDEWEB)

    A.J. Caffrey

    2012-03-01

    The Portable Isotopic Neutron Spectroscopy—PINS, for short—system identifies the chemicals inside munitions and containers without opening them, a decided safety advantage if the fill chemical is a hazardous substance like a chemical warfare agent or an explosive. The PINS Spectrum Identification Guide is intended as a reference for technical professionals responsible for the interpretation of PINS gamma-ray spectra. The guide is divided into two parts. The three chapters that constitute Part I cover the science and technology of PINS. Neutron activation analysis is the focus of Chapter 1. Chapter 2 explores PINS hardware, software, and related operational issues. Gamma-ray spectral analysis basics are introduced in Chapter 3. The six chapters of Part II cover the identification of PINS spectra in detail. Like the PINS decision tree logic, these chapters are organized by chemical element: phosphorus-based chemicals, chlorine-based chemicals, etc. These descriptions of hazardous, toxic, and/or explosive chemicals conclude with a chapter on the identification of the inert chemicals, e.g. sand, used to fill practice munitions.

  7. FDA Certified Mammography Facilities

    Science.gov (United States)

    ... Program Consumer Information (MQSA) Search for a Certified Facility Share Tweet Linkedin Pin it More sharing options ... Email Print This list of FDA Certified Mammography Facilities is updated weekly. If you click on Search ...

  8. Flux pinning in superconductors

    CERN Document Server

    Matsushita, Teruo

    2014-01-01

    The book covers the flux pinning mechanisms and properties and the electromagnetic phenomena caused by the flux pinning common for metallic, high-Tc and MgB2 superconductors. The condensation energy interaction known for normal precipitates or grain boundaries and the kinetic energy interaction proposed for artificial Nb pins in Nb-Ti, etc., are introduced for the pinning mechanism. Summation theories to derive the critical current density are discussed in detail. Irreversible magnetization and AC loss caused by the flux pinning are also discussed. The loss originally stems from the ohmic dissipation of normal electrons in the normal core driven by the electric field induced by the flux motion. The readers will learn why the resultant loss is of hysteresis type in spite of such mechanism. The influence of the flux pinning on the vortex phase diagram in high Tc superconductors is discussed, and the dependencies of the irreversibility field are also described on other quantities such as anisotropy of supercondu...

  9. Flux Pinning in Superconductors

    CERN Document Server

    Matsushita, Teruo

    2007-01-01

    The book covers the flux pinning mechanisms and properties and the electromagnetic phenomena caused by the flux pinning common for metallic, high-Tc and MgB2 superconductors. The condensation energy interaction known for normal precipitates or grain boundaries and the kinetic energy interaction proposed for artificial Nb pins in Nb-Ti, etc., are introduced for the pinning mechanism. Summation theories to derive the critical current density are discussed in detail. Irreversible magnetization and AC loss caused by the flux pinning are also discussed. The loss originally stems from the ohmic dissipation of normal electrons in the normal core driven by the electric field induced by the flux motion. The readers will learn why the resultant loss is of hysteresis type in spite of such mechanism. The influence of the flux pinning on the vortex phase diagram in high Tc superconductors is discussed, and the dependencies of the irreversibility field are also described on other quantities such as anisotropy of supercondu...

  10. PINS-3X Operations

    Energy Technology Data Exchange (ETDEWEB)

    E.H. Seabury

    2013-09-01

    Idaho National Laboratory’s (INL’s) Portable Isotopic Neutron Spectroscopy System (PINS) non-intrusively identifies the chemical fill of munitions and sealed containers. The PINS-3X variant of the system is used to identify explosives and uses a deuterium-tritium (DT) electronic neutron generator (ENG) as the neutron source. Use of the system, including possession and use of the neutron generator and shipment of the system components requires compliance with a number of regulations. This report outlines some of these requirements as well as some of the requirements in using the system outside of INL.

  11. Diffusion inspires selection of pinning nodes in pinning control

    Science.gov (United States)

    Zhou, Ming-Yang; He, Xingsheng; Fu, Zhong-Qian; Liao, Hao; Cai, Shi-min; Zhuo, Zhao

    2016-03-01

    The outstanding problem of controlling a complex network via pinning is related to network dynamics and has the potential to master large-scale real-world systems as well. This paper addresses the heart issue about how to choose pinning nodes for pinning control, where pinning control aims to control a network to an identical state by injecting feedback control signals to a small fraction of nodes. We explore networks' controllability from not only mathematical analysis, but also the aspects of network topology and information diffusion. Then, the connection between pinning control and information diffusion is given, and pinning node selection is transferred into multi-spreader problem in information diffusion. Based on information diffusion, a heuristic method is proposed to select pinning nodes by optimizing the spreading ability of multiple spreaders. The proposed method greatly improves the controllability of large practical networks, and provides a new perspective to investigate pinning node selection.

  12. Pinning Down versus Density

    OpenAIRE

    2015-01-01

    The pinning down number $ {pd}(X)$ of a topological space $X$ is the smallest cardinal $\\kappa$ such that for any neighborhood assignment $U:X\\to \\tau_X$ there is a set $A\\in [X]^\\kappa$ with $A\\cap U(x)\

  13. SIMULATE-4 pin power calculations

    Energy Technology Data Exchange (ETDEWEB)

    Bahadir, T. [Studsvik Scandpower, Inc., 1087 Beacon St., Newton, MA 02459 (United States); Lindahl, S. Oe [Studsvik Scandpower AB, Hantverkargatan 2A, SE-722 12 Vasteraas (Sweden)

    2006-07-01

    A new pin power reconstruction module has been implemented in Studsvik Scandpower's next generation nodal code, SIMULATE-4. Heterogeneous pin powers are calculated by modulating multi-group pin powers from the sub-mesh solver of SIMULATE-4 with pin form factors from single-assembly CASMO-5 lattice calculations. The multi-group pin power model captures instantaneous spectral effects, and actinide tracking on the assembly sub-mesh describes exposure-induced pin power variations. Model details and verification tests against high order multi-assembly transport methods are presented. The accuracy of the new methods is also demonstrated by comparing SIMULATE-4 calculations with measured critical experiment pin powers. (authors)

  14. GLASS MELTING PHENOMENA, THEIR ORDERING AND MELTING SPACE UTILISATION

    Directory of Open Access Journals (Sweden)

    Němec L.

    2013-12-01

    Full Text Available Four aspects of effective glass melting have been defined – namely the fast kinetics of partial melting phenomena, a consideration of the melting phenomena ordering, high utilisation of the melting space, and effective utilisation of the supplied energy. The relations were defined for the specific melting performance and specific energy consumption of the glass melting process which involve the four mentioned aspects of the process and indicate the potentials of effective melting. The quantity “space utilisation” has been treated in more detail as an aspect not considered in practice till this time. The space utilisation was quantitatively defined and its values have been determined for the industrial melting facility by mathematical modelling. The definitions of the specific melting performance and specific energy consumption have been used for assessment of the potential impact of a controlled melt flow and high space utilisation on the melting process efficiency on the industrial scale. The results have shown that even the partial control of the melt flow, leading to the partial increase of the space utilisation, may considerably increase the melting performance, whereas a decrease of the specific energy consumption was determined to be between 10 - 15 %.

  15. Pinning, de-pinning and re-pinning of a slowly varying rivulet

    KAUST Repository

    Paterson, C.

    2013-09-01

    The solutions for the unidirectional flow of a thin rivulet with prescribed volume flux down an inclined planar substrate are used to describe the locally unidirectional flow of a rivulet with constant width (i.e. pinned contact lines) but slowly varying contact angle as well as the possible pinning and subsequent de-pinning of a rivulet with constant contact angle and the possible de-pinning and subsequent re-pinning of a rivulet with constant width as they flow in the azimuthal direction from the top to the bottom of a large horizontal cylinder. Despite being the same locally, the global behaviour of a rivulet with constant width can be very different from that of a rivulet with constant contact angle. In particular, while a rivulet with constant non-zero contact angle can always run from the top to the bottom of the cylinder, the behaviour of a rivulet with constant width depends on the value of the width. Specifically, while a narrow rivulet can run all the way from the top to the bottom of the cylinder, a wide rivulet can run from the top of the cylinder only to a critical azimuthal angle. The scenario in which the hitherto pinned contact lines of the rivulet de-pin at the critical azimuthal angle and the rivulet runs from the critical azimuthal angle to the bottom of the cylinder with zero contact angle but slowly varying width is discussed. The pinning and de-pinning of a rivulet with constant contact angle, and the corresponding situation involving the de-pinning and re-pinning of a rivulet with constant width at a non-zero contact angle which generalises the de-pinning at zero contact angle discussed earlier, are described. In the latter situation, the mass of fluid on the cylinder is found to be a monotonically increasing function of the constant width. © 2013 Elsevier Masson SAS. All rights reserved.

  16. Fuel pin cladding

    Science.gov (United States)

    Vaidyanathan, S.; Adamson, M.G.

    1986-01-28

    Disclosed is an improved fuel pin cladding, particularly adapted for use in breeder reactors, consisting of composite tubing with austenitic steel on the outer portion of the thickness of the tube wall and with nickel and/or ferritic material on the inner portion of the thickness of the tube wall. The nickel forms a sacrificial barrier as it reacts with certain fission products thereby reducing fission product activity at the austenitic steel interface. The ferritic material forms a preventive barrier for the austenitic steel as it is immune to liquid metal embrittlement. The improved cladding permits the use of high density fuel which in turn leads to a better breeding ratio in breeder reactors, and will increase the threshold at which failure occurs during temperature transients. 2 figs.

  17. Fuel pin cladding

    Science.gov (United States)

    Vaidyanathan, Swaminathan; Adamson, Martyn G.

    1986-01-01

    An improved fuel pin cladding, particularly adapted for use in breeder reactors, consisting of composite tubing with austenitic steel on the outer portion of the thickness of the tube wall and with nickel and/or ferritic material on the inner portion of the thickness of the tube wall. The nickel forms a sacrificial barrier as it reacts with certain fission products thereby reducing fission product activity at the austenitic steel interface. The ferritic material forms a preventive barrier for the austenitic steel as it is immune to liquid metal embrittlement. The improved cladding permits the use of high density fuel which in turn leads to a better breeding ratio in breeder reactors, and will increase the threshold at which failure occurs during temperature transients.

  18. Melt processed high-temperature superconductors

    CERN Document Server

    1993-01-01

    The achievement of large critical currents is critical to the applications of high-temperature superconductors. Recent developments have shown that melt processing is suitable for producing high J c oxide superconductors. Using magnetic forces between such high J c oxide superconductors and magnets, a person could be levitated.This book has grown largely out of research works on melt processing of high-temperature superconductors conducted at ISTEC Superconductivity Research Laboratory. The chapters build on melt processing, microstructural characterization, fundamentals of flux pinning, criti

  19. Size effects of nano-scale pinning centers on the superconducting properties of YBCO single grains

    Science.gov (United States)

    Moutalbi, Nahed; Noudem, Jacques G.; M'chirgui, Ali

    2014-08-01

    High pinning superconductors are the most promising materials for power engineering. Their superconducting properties are governed by the microstructure quality and the vortex pinning behavior. We report on a study of the vortex pinning in YBa2Cu3O7-x (YBCO) single grain with defects induced through the addition of insulating nano-particles. In order to improve the critical current density, YBCO textured bulk superconductors were elaborated using the Top Seeded Melt Texture and Growth process with different addition amounts of Al2O3 nano-particles. Serving as strong pinning centers, 0.05% excess of Al2O3 causes a significant enhancement of the critical current density Jc under self field and in magnetic fields at 77 K. The enhanced flux pinning achieved with the low level of alumina nano-particles endorses the effectiveness of insulating nano-inclusions to induce effectives pinning sites within the superconducting matrix. On the other side, we focused on the effect of the size of pinning centers on the critical current density. This work was carried out using two batches of alumina nano-particles characterized by two different particle size distributions with mean diameters PSD1 = 20 nm and PSD2 = 2.27 μm. The matching effects of the observed pinning force density have been compared. The obtained results have shown that the flux pinning is closely dependent on the size of the artificial pinning centers. Our results suggest that the optimization of the size of the artificial pinning centers is crucial to a much better understanding of the pinning mechanisms and therefore to insure high superconducting performance for the practical application of superconducting materials.

  20. Paddle-pin alinement test

    Science.gov (United States)

    Gilliam, D. M.; Foster, J. A.

    1977-01-01

    Segmented insulated test bar speeds up patch distributor paddle-pin test. Device eliminates need to disconnect cables or remove distributor. Printed circuit cable and connector reduces weight on bar, adding to tester portability.

  1. Pinning Mechanisms in YBCO Tapes

    CERN Document Server

    Spera, Marcello; Ballarino, Amalia

    2015-01-01

    In this thesis work, a study on flux pinning mechanisms of commercial YBCO tapes is presented. This study has been performed via critical current characterization using transport (via direct I-V curves) and magnetization (via a Vibrating Sample Magnetometer) measurements. The latter ones turned out to be better concerning the comprehension of the pinning landscape of the provided samples, as a wider range of magnetic fields and temperatures is available for those measurements in the setup I used. The comparison of the experimental data with existing theoretical models allowed me to draw a picture of the pinning mechanisms underlying in each sample, and they turned out to be quite different one another. Moreover, for high-performance research tapes, another interesting feature has been found: the counterplay between the self-field critical current and the in-field one. Very well engineered artificial pinning structures limit the self-field critical current density due to the hi...

  2. Enhanced pinning in superconducting thin films with graded pinning landscapes

    Science.gov (United States)

    Motta, M.; Colauto, F.; Ortiz, W. A.; Fritzsche, J.; Cuppens, J.; Gillijns, W.; Moshchalkov, V. V.; Johansen, T. H.; Sanchez, A.; Silhanek, A. V.

    2013-05-01

    A graded distribution of antidots in superconducting a-Mo79Ge21 thin films has been investigated by magnetization and magneto-optical imaging measurements. The pinning landscape has maximum density at the sample border, decreasing linearly towards the center. Its overall performance is noticeably superior than that for a sample with uniformly distributed antidots: For high temperatures and low fields, the critical current is enhanced, whereas the region of thermomagnetic instabilities in the field-temperature diagram is significantly suppressed. These findings confirm the relevance of graded landscapes on the enhancement of pinning efficiency, as recently predicted by Misko and Nori [Phys. Rev. B 85, 184506 (2012)].

  3. Interface roughening and pinning

    Science.gov (United States)

    Roux, Stéphane; Hansen, Alex

    1994-04-01

    We study a simple model for thé pinning of an interface by impurities with random strengths, and thé depinning due to thé applied pressure, in a quasi-static propagation lirait. The model is very close to thé so called "Robin Hood" model introduced by Zaitsev. It is designed to describe e.g. thé invasion of a wetting fluid (imbibition) in a heterogeneous porous medium containing a second immiscible fluid. The relation between this model and other previously proposed approaches is discussed. The front of thé invaded domain is shown to develop a self-affine structure with an increase of thé roughness as a power-law of thé injected volume. The value of thé apparent roughness exponent can be favorably compared to some experimental measurements although we argue that thé true roughness exponent is out of reach of commonly used methods. We show that thé distribution f(d, Δ t) of distances d between discrete local invasions at a time interval Δ t can be described by a scaling law f(d, Δ t) = d^{-1}\\varphi(d/sqrt{Δ t}). This form can be obtained from thé identification of a hierarchical structure of "bursts" in thé pressure signal. Those "bursts" are quahtatively similar to those observed in quasistatic drainage, (i.e. invasion percolation), although characterized by différent scaling indices. Nous étudions un modèle simple pour analyser l'accrochage d'une interface sur des impuretés et le décrochage sous l'effet d'une pression appliquée, dans une limite quasi-statique. Ce modèle est très voisin du modèle "Robin Hood" introduit par Zaitsev. Il s'applique en particulier à l'invasion d'un fluide mouillant (imbibition) dans un milieu poreux hétérogène contenant un fluide immiscible. Nous discutons les relations entre ce modèle et d'autres approches proposées pour décrire ce phénomène. Le front d'invasion acquiert une structure auto-affine, avec un développement de la rugosité selon une loi de puissance du volume injecté. La valeur de l

  4. PinBus Interface Design

    Energy Technology Data Exchange (ETDEWEB)

    Hammerstrom, Donald J.; Adgerson, Jewel D.; Sastry, Chellury; Pratt, Richard M.; Pratt, Robert G.

    2009-12-30

    On behalf of the U.S. Department of Energy, PNNL has explored and expanded upon a simple control interface that might have merit for the inexpensive communication of smart grid operational objectives (demand response, for example) to small electric end-use devices and appliances. The approach relies on bi-directional communication via the electrical voltage states of from one to eight shared interconnection pins. The name PinBus has been suggested and adopted for the proposed interface protocol. The protocol is defined through the presentation of state diagrams and the pins’ functional definitions. Both simulations and laboratory demonstrations are being conducted to demonstrate the elegance and power of the suggested approach. PinBus supports a very high degree of interoperability across its interfaces, allowing innumerable pairings of devices and communication protocols and supporting the practice of practically any smart grid use case.

  5. Synchronizability on complex networks via pinning control

    Indian Academy of Sciences (India)

    Yi Liang; Xingyuan Wang

    2013-04-01

    It is proved that the maximum eigenvalue sequence of the principal submatrices of coupling matrix is decreasing. The method of calculating the number of pinning nodes is given based on this theory. The findings reveal the relationship between the decreasing speed of maximum eigenvalue sequence of the principal submatrices for coupling matrix and the synchronizability on complex networks via pinning control. We discuss the synchronizability on some networks, such as scale-free networks and small-world networks. Numerical simulations show that different pinning strategies have different pinning synchronizability on the same complex network, and the synchronizability with pinning control is consistent with one without pinning control in various complex networks.

  6. Facile fabrication of luminescent organic dots by thermolysis of citric acid in urea melt, and their use for cell staining and polyelectrolyte microcapsule labelling

    Directory of Open Access Journals (Sweden)

    Nadezhda M. Zholobak

    2016-12-01

    Full Text Available Luminescent organic dots (O-dots were synthesized via a one-pot, solvent-free thermolysis of citric acid in urea melt. The influence of the ratio of the precursors and the duration of the process on the properties of the O-dots was established and a mechanism of their formation was hypothesized. The multicolour luminescence tunability and toxicity of synthesized O-dots were extensively studied. The possible applications of O-dots for alive/fixed cell staining and labelling of layer-by-layer polyelectrolyte microcapsules were evaluated.

  7. Facile fabrication of luminescent organic dots by thermolysis of citric acid in urea melt, and their use for cell staining and polyelectrolyte microcapsule labelling.

    Science.gov (United States)

    Zholobak, Nadezhda M; Popov, Anton L; Shcherbakov, Alexander B; Popova, Nelly R; Guzyk, Mykhailo M; Antonovich, Valeriy P; Yegorova, Alla V; Scrypynets, Yuliya V; Leonenko, Inna I; Baranchikov, Alexander Ye; Ivanov, Vladimir K

    2016-01-01

    Luminescent organic dots (O-dots) were synthesized via a one-pot, solvent-free thermolysis of citric acid in urea melt. The influence of the ratio of the precursors and the duration of the process on the properties of the O-dots was established and a mechanism of their formation was hypothesized. The multicolour luminescence tunability and toxicity of synthesized O-dots were extensively studied. The possible applications of O-dots for alive/fixed cell staining and labelling of layer-by-layer polyelectrolyte microcapsules were evaluated.

  8. Thermal-Hydraulic Simulations of Single Pin and Assembly Sector for IVG- 1M Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kraus, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Garner, P. [Argonne National Lab. (ANL), Argonne, IL (United States); Hanan, N. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-01-15

    inner pin just before the enrichment change. The 600 mm case demonstrated a peak clad surface temperature of 370.4 K, while the 800 mm case had a temperature of 391.6 K. These temperatures are well below the necessary temperatures for boiling to occur at the rated pressure. Fuel temperatures are also well below the melting point. Future bundle work will include simulations of the proposed low-enriched uranium (LEU) design. Two transient scenarios were also investigated for the single-pin geometries. Both were “model” problems that were focused on pure thermal-hydraulic behavior, and as such were simple power changes that did not incorporate neutron kinetics modeling. The first scenario was a high-power, ramp increase, while the second scenario was a low-power, step increase. A cylindrical RELAP model was also constructed to investigate its accuracy as compared to the higher-fidelity CFD. Comparisons between the two codes showed good agreement for peak temperatures in the fuel and at the cladding surface for both cases. In the step transient, temperatures at four axial levels were also computed. These showed greater but reasonable discrepancy, with RELAP outputting higher temperatures. These results provide some evidence that RELAP can be used with confidence in modeling transients for IVG.

  9. Improved pinning regime by energetic ions using reduction of pinning potential

    Energy Technology Data Exchange (ETDEWEB)

    Weinstein, Roy; Gandini, Alberto; Sawh, Ravi-Persad; Parks, Drew; Mayes, Bill

    2003-05-15

    When ion damage is used to create pinning centers, full columnar pinning centers provide the largest pinning potential, U{sub pin}, but not the greatest J{sub c} or pinned field, B{sub pin}. Some of the characteristics of columnar defects which limit J{sub c} and B{sub pin} are discussed, including reduction of percolation path, and the need for a larger number of columns of damage, for pinning, than are usually estimated. It is concluded that columnar pinning centers are limited to B{sub pin}<4 T, and also severely reduce J{sub c}. Evidence is reviewed that aligned damage, or broken-columnar pinning centers, described herein, can provide orders of magnitude higher J{sub c}, and higher pinned field, despite providing lower U{sub pin}. A pinning center morphology is discussed which utilizes multiple-in-line-damage (MILD). For, e.g., present day large grain HTS J{sub c}, obtainable by MILD pinning, is estimated to be of the order of 10{sup 6} A/cm{sup 2} at 77 K, even when crystal plane alignment and weak links are not improved. Pinned field is increased by over an order of magnitude. An experiment is proposed to confirm these observations, and to directly compare MILD to columnar pinning centers. It will also determine the optimum MILD structure. Other measurements of interest, made possible by the same data set, are described.

  10. The induction furnace as a melting facility in steel production. Pt. 1. Features of induction furnaces used in steel production; Der Induktionsofen als Schmelzaggregat fuer die Stahlerzeugung. T. 1. Merkmale von Induktionsoefen in der Stahlerzeugung

    Energy Technology Data Exchange (ETDEWEB)

    Chaabet, Mohamed; Doetsch, Erwin [ABP Induction Systems GmbH, Dortmund (Germany)

    2011-12-15

    Global steel output has now been growing extremely rapidly for a prolonged time; in the past ten years alone, annual production has risen from 851 million t/a (in 2001) to 1417 million t/a (2010), as a result, primarily, of growth in China. Electric steel production using the electric arc furnace as the classical melting facility is around 45 % world-wide, with a rising trend (but excluding the special case of China, where oxygen-route steel holds a 90 % share of production). Following the development of induction technology and inverter outputs of over 40 MW for crucible furnaces with capacities of above 65 t, the induction furnace is now available as an alternative electrical melting installation for use in smaller mini steel mills. The benefits of this technology can be found in high feed-material efficiencies and low environmental and workplace burdens, in addition to the absence of electrode costs and the only modest demands made on the power-supply grid. These features of the induction furnace and their special significance for steel production are examined in Part 1 of this article. The second part of the article then focuses on examples of the use of induction furnaces in the steelmaking plant. (orig.)

  11. Snow-melting facilities capable of meeting multiple needs. Present state and future tasks in a Ministry of Construction jurisdiction in Tohoku District; Tohoku chiken kannai ni okeru doro shoyusetsu shisetsu no genjo to kadai

    Energy Technology Data Exchange (ETDEWEB)

    Tezuka, N. [Ministry of Construction, Tokyo (Japan)

    1997-11-01

    Novel snow-melting facilities in use in Tohoku District, Japan, are described. One operates on a heat source in which heat is generated in the composting process. Grass, cattle droppings, and clay as a fermentation promoter are blended, and the blend is allowed to ferment. The obtained heat travels through a non-freezing liquid serving as a heater exchanger, and fed into snow-melting pipes. Laboratory tests are conducted, and it is found that the best fermentation occurs when the compost is a blend of 20% glass and 80% cattle droppings. At the air temperature of 0-5degC, heat is continuously emitted at approximately 40degC. This system may prove to be feasible when 40-50m{sup 2} is the size of the area to cover. The disposal of compost and the management of grass are the tasks to be dealt with in the future. The other utilizes wind force. Power produced by a wind turbine is used for road heating and tunnel lighting, and operates sight line guidance. The wind turbine introduced here outputs 250kW, producing a yearly total of 489.2kW. There is a plan for a verification test using a small wind power generator. Future tasks include the sale of surplus power, measures for noise reduction, and measures for preventing an adverse impact on TV, etc. 2 figs., 3 tabs.

  12. Pinning-controllability of complex networks

    OpenAIRE

    Sorrentino, Francesco; Di Bernardo, Mario; Garofalo, Franco; Chen, Guanrong

    2007-01-01

    We study the problem of controlling a general complex network towards an assigned synchronous evolution, by means of a pinning control strategy. We define the pinning-controllability of the network in terms of the spectral properties of an extended network topology. The roles of the control and coupling gains as well as of the number of pinned nodes are also discussed.

  13. Self-shearing retentive pins: a laboratory evaluation of pin channel penetration before shearing.

    Science.gov (United States)

    Barkmeier, W W; Cooley, R L

    1979-09-01

    This laboratory study determined the depth reached by self-shearing pins in dentin pin channels. Pin channels were prepared with the self-limiting shoulder twist drill for each of the four systems tested. Mean channel depth reached for the various pin systems was: Stabilok (small), 2.31 mm; Stabilok (medium), 1.78 mm; Reten Pin, 1.40 mm; and TMS (Regular), 2.04 mm. A coparison was also made by calculating the mean percent of penetration in relation to the depth of prepared pin channel: Stabilok (small), 92.50%; Stabilok (medium), 63.62%; Reten Pin, 66.67%; and TMS (Regular) 81.75%.

  14. INCREASING EFFICIENCY OF REPAIRING, MANUFACTURING AND OPERATION OF THE TPP FACILITIES BY TECHNOLOGY OF GAS-THERMAL COATING AND LASER SURFACE MELTING

    Directory of Open Access Journals (Sweden)

    O. E. Grachev

    2015-01-01

    Full Text Available The article considers effectiveness increase of the TPP heat-mechanical equipment repair, manufacturing and maintenance as exemplified by gas-thermal technique for hardening laststages rotor blades of the steam turbines. The rotor blades work under conditions of intense power loading, their airfoil being erosion-corrosion destructed by the action of the moist-steam flow. Repairing companies employ quite a number of technologies to restore some of erosion-worn rotor blades. Inter alia, argon-arc, plasma and gas-powder weld deposition of the original material with subsequent machining, stellite protection recovery, electrical spark alloying the entry edge mat surface, spraying ion-plasma coating on the blade airfoil surface. In domestic turbine building, rotor blades of the steam turbines last stages are manufactured of martensitic class stainless steel. The key condition for successful blade restoration is thermal effect minimizing on the base material for excluding the slag areas possible forming. The laser surface coating technology provides these conditions. They coat the surface of an item being processed by way of melting the base and the adding material. In as much the base melts smallest, the coating characteristics depend mainly on the properties of adding material. The procedure of laser coating passes through several stages including physical contact creation, chemical interaction (laser radiation absorption, volumetrical processes resulting in formation of stable bonds in volume of the materials that have reacted. For the low-pressure cylinder rotor blades supplementary protection against erosion destruction, LLC ‘Technological Systems of Protective Coating’ developed technology of the blade airfoil protective finish by method of high-speed gas-flame sputter. The company realized this technology in 2012 during K-200-12,8 turbine (of the Leningrad Metallurgical Works – LMZ repairing in Zainsk SDPP by JSC ‘Tatenergo’. The

  15. Pinning control of chimera states

    Science.gov (United States)

    Gambuzza, Lucia Valentina; Frasca, Mattia

    2016-08-01

    The position of the coherent and incoherent domain of a chimera state in a ring of nonlocally coupled oscillators is strongly influenced by the initial conditions, making nontrivial the problem of confining them in a specific region of the structure. In this paper we propose the use of spatial pinning to induce a chimera state where the nodes belonging to one domain, either the coherent or the incoherent, are fixed by the control action. We design two different techniques according to the dynamics to be forced in the region of pinned nodes, and validate them on FitzHugh-Nagumo and Kuramoto oscillators. Furthermore, we introduce a suitable strategy to deal with the effects of finite size in small structures.

  16. Be on Pins and Needles

    Institute of Scientific and Technical Information of China (English)

    周立

    2003-01-01

    英语对话:A:It seems you’re on pins and needles today.Anything troubling you?B:Yeah.I don’t know why bad things keep happening to me .You see,mycar was stolen and the warehouse had been broken into.I can’t keep myfinger on the causes of this damned thing.A:There must be someone who had planned that.Do you have a partieularperson in mind?

  17. Investigation of the bulk pinning force in YBCO superconducting films with nano-engineered pinning centres

    Science.gov (United States)

    Crisan, A.; Dang, V. S.; Yearwood, G.; Mikheenko, P.; Huhtinen, H.; Paturi, P.

    2014-08-01

    For practical applications of superconducting materials in applied magnetic fields, artificial pinning centres in addition to natural ones are required to oppose the Lorentz force. These pinning centres are actually various types of defects in the superconductor matrix. The pinning centres can be categorised on their dimension (volume, surface, or point) and on their character (normal cores or Δκ cores). We have used the Dew Hughes approach to determine the types of pinning centres present in various samples, with various thicknesses, temperatures and nanostructured additions to the superconducting matrix. Results show that normal surface pinning centres are present throughout almost all the samples, as dominant pinning mechanism. Such 2D extended pinning centres are mainly due to dislocations, grain boundaries, nanorods. Strong normal point pinning centres were found to be common in BZO doped YBCO samples. Other types of pinning centres, in various (minor) concentrations were also found in some of the samples.

  18. Melt Rate Improvement for DWPF MB3: Melt Rate Furnace Testing

    Energy Technology Data Exchange (ETDEWEB)

    Stone, M.E.

    2001-07-24

    The Defense Waste Processing Facility (DWPF) would like to increase its canister production rate. The goal of this study is to improve the melt rate in DWPF specifically for Macrobatch 3. However, the knowledge gained may result in improved melting efficiencies translating to future DWPF macrobatches and in higher throughput for other Department of Energy's (DOE) melters. Increased melting efficiencies decrease overall operational costs by reducing the immobilization campaign time for a particular waste stream. For melt rate limited systems, a small increase in melting efficiency translates into significant hard dollar savings by reducing life cycle operational costs.

  19. Alignment Pins for Assembling and Disassembling Structures

    Science.gov (United States)

    Campbell, Oliver C.

    2008-01-01

    Simple, easy-to-use, highly effective tooling has been devised for maintaining alignment of bolt holes in mating structures during assembly and disassembly of the structures. The tooling was originally used during removal of a body flap from the space shuttle Atlantis, in which misalignments during removal of the last few bolts could cause the bolts to bind in their holes. By suitably modifying the dimensions of the tooling components, the basic design of the tooling can readily be adapted to other structures that must be maintained in alignment. The tooling includes tapered, internally threaded alignment pins designed to fit in the bolt holes in one of the mating structures, plus a draw bolt and a cup that are used to install or remove each alignment pin. In preparation for disassembly of two mating structures, external supports are provided to prevent unintended movement of the structures. During disassembly of the structures, as each bolt that joins the structures is removed, an alignment pin is installed in its place. Once all the bolts have been removed and replaced with pins, the pins maintain alignment as the structures are gently pushed or pulled apart on the supports. In assembling the two structures, one reverses the procedure described above: pins are installed in the bolt holes, the structures are pulled or pushed together on the supports, then the pins are removed and replaced with bolts. The figure depicts the tooling and its use. To install an alignment pin in a bolt hole in a structural panel, the tapered end of the pin is inserted from one side of the panel, the cup is placed over the pin on the opposite side of the panel, the draw bolt is inserted through the cup and threaded into the pin, the draw bolt is tightened to pull the pin until the pin is seated firmly in the hole, then the draw bolt and cup are removed, leaving the pin in place. To remove an alignment pin, the cup is placed over the pin on the first-mentioned side of the panel, the draw

  20. Postirradiation examinations of fuel pins from the GCFR F-1 series of mixed-oxide fuel pins at 5. 5 at. % burnup

    Energy Technology Data Exchange (ETDEWEB)

    Strain, R V; Johnson, C E

    1978-05-01

    Postirradiation examinations were performed on five fuel pins from the Gas-Cooled Fast-Breeder Reactor F-1 experiment irradiated in EBR-II to a peak burnup of approximately 5.5 at. %. These encapsulated fuel pins were irradiated at peak-power linear ratings from approximately 13 to 15 kW/ft and peak cladding inside diameter temperatures from approximately 625 to 760/sup 0/C. The maximum diametral change that occurred during irradiation was 0.2% ..delta..D/D/sub 0/. The maximum fuel-cladding chemical interaction depth was 2.6 mils in fuel pin G-1 and 1 mil or less in the other three pins examined destructively. Significant migration of the volatile fission products occurred axially to the fuel-blanket interfaces. Teh postirradiation examination data indicate that fuel melted at the inner surface of the annular fuel pellets in the two highest power rating fuel pins, but little axial movement of fuel occurred.

  1. Spectroscopic amplifier for pin diode; Amplificador espectroscopico para diodo Pin

    Energy Technology Data Exchange (ETDEWEB)

    Alonso M, M. S.; Hernandez D, V. M.; Vega C, H. R., E-mail: bebe.luna_s@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)

    2014-10-15

    The photodiode remains the basic choice for the photo-detection and is widely used in optical communications, medical diagnostics and field of corpuscular radiation. In detecting radiation it has been used for monitoring radon and its progeny and inexpensive spectrometric systems. The development of a spectroscopic amplifier for Pin diode is presented which has the following characteristics: canceler Pole-Zero (P/Z) with a time constant of 8 μs; constant gain of 57, suitable for the acquisition system; 4th integrator Gaussian order to waveform change of exponential input to semi-Gaussian output and finally a stage of baseline restorer which prevents Dc signal contribution to the next stage. The operational amplifier used is the TLE2074 of BiFET technology of Texas Instruments with 10 MHz bandwidth, 25 V/μs of slew rate and a noise floor of 17 nv/(Hz)1/2. The integrated circuit has 4 operational amplifiers and in is contained the total of spectroscopic amplifier that is the goal of electronic design. The results show like the exponential input signal is converted to semi-Gaussian, modifying only the amplitude according to the specifications in the design. The total system is formed by the detector, which is the Pin diode, a sensitive preamplifier to the load, the spectroscopic amplifier that is what is presented and finally a pulse height analyzer (Mca) which is where the spectrum is shown. (Author)

  2. Uncertainty of pin height measurement for the determination of wear in pin-on-plate test

    DEFF Research Database (Denmark)

    Drago, Nicola; De Chiffre, Leonardo; Poulios, Konstantinos

    2014-01-01

    machine (CMM), achieving an expanded measurement uncertainty (k = 2) better than 1 mm. A simple dedicated fixture adaptable to workshop environment was developed and its metrological capability investigated, estimating an average uncertainty of measurement in the order of 5 mm (k = 2). Fixture......The paper concerns measurement of pin height for the determination of wear in a pin-on-plate (POP) or pin-on-disc (POD) test, where a pin is mounted on a holder that can be fixed on the test rig and removed for measurements. The amount of wear is assessed as difference of pin height before...... and after the test, using the distance between holder plane and pin friction plane as measurand. A series of measurements were performed in connection with POP testing of different friction material pins mounted on an aluminium holder. Pin height measurements were carried out on a coordinate measuring...

  3. Improved shock-detection pin arrangement

    Energy Technology Data Exchange (ETDEWEB)

    Erskine, D.J.

    1995-08-01

    Shockwave speeds are often measured by comparing arrival times at the tips of electrical shorting pins in a hexagonal array over two elevations (called up and down). In the conventional arrangement, the center pin is solely responsible for measuring the curvature of the wavefront. Without this datum the shock speed cannot be precisely determined. In some experiments this pin fail frequently enough to be a problem. We report a simple rearrangement between up and down designated pins which eliminates the critical reliance on a single.

  4. PIN1 gene variants in Alzheimer's disease

    Directory of Open Access Journals (Sweden)

    Siedlecki Janusz

    2009-11-01

    Full Text Available Abstract Background Peptidyl-prolyl isomerase, NIMA-interacting 1 (PIN1 plays a significant role in the brain and is implicated in numerous cellular processes related to Alzheimer's disease (AD and other neurodegenerative conditions. There are confounding results concerning PIN1 activity in AD brains. Also PIN1 genetic variation was inconsistently associated with AD risk. Methods We performed analysis of coding and promoter regions of PIN1 in early- and late-onset AD and frontotemporal dementia (FTD patients in comparison with healthy controls. Results Analysis of eighteen PIN1 common polymorphisms and their haplotypes in EOAD, LOAD and FTD individuals in comparison with the control group did not reveal their contribution to disease risk. In six unrelated familial AD patients four novel PIN1 sequence variants were detected. c.58+64C>T substitution that was identified in three patients, was located in an alternative exon. In silico analysis suggested that this variant highly increases a potential affinity for a splicing factor and introduces two intronic splicing enhancers. In the peripheral leukocytes of one living patient carrying the variant, a 2.82 fold decrease in PIN1 expression was observed. Conclusion Our data does not support the role of PIN1 common polymorphisms as AD risk factor. However, we suggest that the identified rare sequence variants could be directly connected with AD pathology, influencing PIN1 splicing and/or expression.

  5. Thermal fluctuations and phase diagrams of the phase-field crystal model with pinning.

    Science.gov (United States)

    Ramos, J A P; Granato, E; Achim, C V; Ying, S C; Elder, K R; Ala-Nissila, T

    2008-09-01

    We study the influence of thermal fluctuations in the phase diagram of a recently introduced two-dimensional phase field crystal model with an external pinning potential. The model provides a continuum description of pinned lattice systems allowing for both elastic deformations and topological defects. We introduce a nonconserved version of the model and determine the ground-state phase diagram as a function of lattice mismatch and strength of the pinning potential. Monte Carlo simulations are used to determine the phase diagram as a function of temperature near commensurate phases. The results show a rich phase diagram with commensurate, incommensurate, and liquidlike phases with a topology strongly dependent on the type of ordered structure. A finite-size scaling analysis of the melting transition for the c(2x2) commensurate phase shows that the thermal correlation length exponent nu and specific heat behavior are consistent with the Ising universality class as expected from analytical arguments.

  6. Melting of metallic intermediate level waste

    Energy Technology Data Exchange (ETDEWEB)

    Huutoniemi, Tommi; Larsson, Arne; Blank, Eva [Studsvik Nuclear AB, Nykoeping (Sweden)

    2013-08-15

    This report presents a feasibility study of a melting facility for core components and reactor internals. An overview is given of how such a facility for treatment of intermediate level waste might be designed, constructed and operated and highlights both the possibilities and challenges. A cost estimate and a risk analysis are presented in order to make a conclusion of the technical feasibility of such a facility. Based on the authors' experience in operating a low level waste melting facility, their conclusion is that without technical improvements such a facility is not feasible today. This is based on the cost of constructing and operating such a facility, in conjunction with the radiological risks associated with operation and the uncertain benefits to disposal and long term safety.

  7. The maize PIN gene family of auxin transporters

    Directory of Open Access Journals (Sweden)

    Cristian eForestan

    2012-02-01

    Full Text Available Auxin is a key regulator of plant development and its differential distribution in plant tissues, established by a polar cell-to-cell transport, can trigger a wide range of developmental processes. A few members of the two families of auxin efflux transport proteins, PIN-formed (PIN and P-glycoprotein (ABCB/PGP, have so far been characterized in maize. Nine new Zea mays auxin efflux carriers PIN family members and two maize PIN-like genes have now been identified. Four members of PIN1 (named ZmPIN1a–d cluster, one gene homologous to AtPIN2 (ZmPIN2, three orthologs of PIN5 (ZmPIN5a–c, one gene paired with AtPIN8 (ZmPIN8, and three monocot-specific PINs (ZmPIN9, ZmPIN10a and b were cloned and the phylogenetic relationships between early land plants, monocots and eudicots PIN proteins investigated, including the new maize PIN proteins. Tissue-specific expression patterns of the twelve maize PIN genes, two PIN-like genes and ZmABCB1, an ABCB auxin efflux carrier, were analyzed using semi-quantitative RT–PCR. ZmPIN gene transcripts have overlapping expression domains in the root apex, during male and female inflorescence differentiation and kernel development. However, some PIN family members have specific tissue localization: ZmPIN1d transcript marks the L1 layer of the SAM and IM during the flowering transition and the monocot-specific ZmPIN9 is expressed in the root endodermis and pericycle. The phylogenetic and gene structure analyses together with the expression pattern of the ZmPIN gene family indicate that subfunctionalization of some maize PINs can be associated to the differentiation and development of monocot-specific organs and tissues and might have occurred after the divergence between dicots and monocots.

  8. Pinning impulsive control algorithms for complex network.

    Science.gov (United States)

    Sun, Wen; Lü, Jinhu; Chen, Shihua; Yu, Xinghuo

    2014-03-01

    In this paper, we further investigate the synchronization of complex dynamical network via pinning control in which a selection of nodes are controlled at discrete times. Different from most existing work, the pinning control algorithms utilize only the impulsive signals at discrete time instants, which may greatly improve the communication channel efficiency and reduce control cost. Two classes of algorithms are designed, one for strongly connected complex network and another for non-strongly connected complex network. It is suggested that in the strongly connected network with suitable coupling strength, a single controller at any one of the network's nodes can always pin the network to its homogeneous solution. In the non-strongly connected case, the location and minimum number of nodes needed to pin the network are determined by the Frobenius normal form of the coupling matrix. In addition, the coupling matrix is not necessarily symmetric or irreducible. Illustrative examples are then given to validate the proposed pinning impulsive control algorithms.

  9. Nanoscale pinning effect evaluated from deformed nanobubbles

    Science.gov (United States)

    Teshima, Hideaki; Nishiyama, Takashi; Takahashi, Koji

    2017-01-01

    Classical thermodynamics theory predicts that nanosized bubbles should disappear in a few hundred microseconds. The surprisingly long lifetime and stability of nanobubbles are therefore interesting research subjects. It has been proposed that the stability of nanobubbles arises through pinning of the three-phase contact line, which results from intrinsic nanoscale geometrical and chemical heterogeneities of the substrate. However, a definitive explanation of nanobubble stability is still lacking. In this work, we examined the stability mechanism by introducing a "pinning force." We investigated nanobubbles at a highly ordered pyrolytic graphite/pure water interface by peak force quantitative nano-mechanical mapping and estimated the pinning force and determined its maximum value. We then observed the shape of shrinking nanobubbles. Because the diameter of the shrinking nanobubbles was pinned, the height decreased and the contact angle increased. This phenomenon implies that the stability results from the pinning force, which flattens the bubble through the pinned three-phase contact line and prevents the Laplace pressure from increasing. The pinning force can also explain the metastability of coalesced nanobubbles, which have two semispherical parts that are joined to form a dumbbell-like shape. The pinning force of the semispherical parts was stronger than that of the joint region. This result demonstrates that the contact line of the semispherical parts is pinned strongly to keep the dumbbell-like shape. Furthermore, we proposed a nanobubble generation mechanism for the solvent-exchange method and explained why the pinning force of large nanobubbles was not initially at its maximum value, as it was for small nanobubbles.

  10. Pattern Reconfigurable Patch Antenna menggunakan Edge Shorting Pin dan Symmetrical Control Pin

    Directory of Open Access Journals (Sweden)

    DWI ANDI NURMANTRIS

    2016-02-01

    Full Text Available Abstrak Metode baru dalam mendesain suatu pattern reconfigurable antenna telah diteliti. Penelitian ini fokus pada optimasi antena patch lingkaran single layer pencatuan probe koaksial dengan mengintegrasikan 24 switch/shorting pin pada sisi patch yang disebut edge shorting pin dan 8 shorting pin membentuk lingkaran dengan radius tertentu dan selanjutnya disebut symmetrical control pin yang fungsinya sebagai metode penyepadan impedansi. Algoritma Genetika yang dikombinasikan dengan Finite Element Software digunakan untuk mengoptimasi kombinasi  switch, radius lingkaran symmetrical control pin, dan radius patch untuk mendapatkan kemampuan pattern reconfigurability. Antena ini menghasilkan 8 kemungkinan arah radiasi azzimuth dengan resolusi 45o dan arah elevasi 30o pada frekuensi 2,4 Ghz. Optimasi, simulasi, fabrikasi, dan pengukuran dilakukan untuk memverifikasi hasil penelitian. Kata kunci: Patch Lingkaran, Edge Shorting Pin, Symmetrical Control Pin, Algoritma Genetika, Pattern Reconfigurable   Abstract New method for desaining pattern reconfigurable antenna was studied. This study focuses on the optimization of a single layer circular patch antenna with probe feed by integrating the 24 switch / shorting pin on the side of the patch that called Edge Shorting Pins and 8 shorting pins form circular line in such radius that called Symmetrical Control Pins as a impedance matching method. Genetic algorithm combined with the Finite Element Software is used to optimize the switch combination, the radius of circular line of symmetrical control pins, and the patch radius to obtain a pattern reconfigurability capabilities. This antenna produces 8 possible directions of azimuth radiation with a resolution of 45o and 30o elevation direction at a frequency of 2.4 GHz. Optimization, simulation, fabrication, and measurement was done to verify the results. Keywords: Circular Patch, Edge Shorting Pin, Symmetrical Control Pin, Genetic Algorithm, Pattern

  11. Effects of Auxins on PIN-FORMED2 (PIN2) Dynamics Are Not Mediated by Inhibiting PIN2 Endocytosis.

    Science.gov (United States)

    Jásik, Ján; Bokor, Boris; Stuchlík, Stanislav; Mičieta, Karol; Turňa, Ján; Schmelzer, Elmon

    2016-10-01

    By using the photoconvertible fluorescence protein Dendra2 as a tag we demonstrated that neither the naturally occurring auxins indole-3-acetic acid and indole-3-butyric acid, nor the synthetic auxin analogs 1-naphthaleneacetic acid and 2,4-dichlorophenoxyacetic acid nor compounds inhibiting polar auxin transport such as 2,3,5-triiodobenzoic acid and 1-N-naphthylphthalamic acid, were able to inhibit endocytosis of the putative auxin transporter PIN-FORMED2 (PIN2) in Arabidopsis (Arabidopsis thaliana) root epidermis cells. All compounds, except Indole-3-butyric acid, repressed the recovery of the PIN2-Dendra2 plasma membrane pool after photoconversion when they were used in high concentrations. The synthetic auxin analogs 1-naphthaleneacetic acid and 2,4-dichlorophenoxyacetic acid showed the strongest inhibition. Auxins and auxin transport inhibitors suppressed also the accumulation of both newly synthesized and endocytotic PIN2 pools in Brefeldin A compartments (BFACs). Furthermore, we demonstrated that all compounds are also interfering with BFAC formation. The synthetic auxin analogs caused the highest reduction in the number and size of BFACs. We concluded that auxins and inhibitors of auxin transport do affect PIN2 turnover in the cells, but it is through the synthetic rather than the endocytotic pathway. The study also confirmed inappropriateness of the BFA-based approach to study PIN2 endocytosis because the majority of PIN2 accumulating in BFACs is newly synthesized and not derived from the plasma membrane. © 2016 American Society of Plant Biologists. All Rights Reserved.

  12. Pinning controllability of complex networks with community structure.

    Science.gov (United States)

    Miao, Qingying; Tang, Yang; Kurths, Jürgen; Fang, Jian-an; Wong, W K

    2013-09-01

    In this paper, we study the controllability of networks with different numbers of communities and various strengths of community structure. By means of simulations, we show that the degree descending pinning scheme performs best among several considered pinning schemes under a small number of pinned nodes, while the degree ascending pinning scheme is becoming more powerful by increasing the number of pinned nodes. It is found that increasing the number of communities or reducing the strength of community structure is beneficial for the enhancement of the controllability. Moreover, it is revealed that the pinning scheme with evenly distributed pinned nodes among communities outperforms other kinds of considered pinning schemes.

  13. Vortex melting and the liquid state in YBa{sub 2}Cu{sub 3}O{sub x}.

    Energy Technology Data Exchange (ETDEWEB)

    Crabtree, G. W.

    1998-11-18

    The experimental vortex phase diagram of YBa{sub 2}Cu{sub 3}O{sub x} is reviewed, with emphasis on first order vortex melting, the upper and lower critical points on the melting line, and the effect of disorder arising from twin boundary and point defect pinning.

  14. Assessment of Radiographic Image Quality by Visual Examination of Neutron Radiographs of the Calibration Fuel Pin

    DEFF Research Database (Denmark)

    Domanus, Joseph Czeslaw

    1986-01-01

    Up till now no reliable radiographic image quality standards exist for neutron radiography of nuclear reactor fuel. Under the Euratoro Neutron Radiography Working Group (NRWG) Test Program neutron radiographs were produced at different neutron radiography facilities within the European Community...... of a calibration fuel pin. The radiographs were made by the direct, transfer and tracketch methods using different film recording materials. These neutron radiographs of the calibration fuel pin were used for the assessement of radiographic image quality. This was done by visual examination of the radiographs...

  15. The problem of the open safety pin.

    Science.gov (United States)

    Marsh, B R

    1975-01-01

    The open safety pin lodged in the stomach or esophagus presents a challenge to surgical judgment and technical skill. Most foreign bodies causing trouble lodge in the esophagus. Once in the stomach, uneventful passage can be expected in 80 to 90% of cases. Active intervention is reserved for those where intestinal performation is likely or where there is failure to progress. We have used the fiberesophagoscope to remove three open safety pins from the stomachs of two patients whose symptoms and threat of perforation required intervention. The microbiopsy forceps was used successfully to retrieve the open pins, but a newly developed grasping forceps for use with the fiberesophagoscope now provides a more secure hold on such foreign bodies. Rigid instruments retain their value for selected cases, but the flexible equipment now provides an important advance in the management of the open safety pin in the stomach.

  16. Pinning Synchronization of Switched Complex Dynamical Networks

    Directory of Open Access Journals (Sweden)

    Liming Du

    2015-01-01

    Full Text Available Network topology and node dynamics play a key role in forming synchronization of complex networks. Unfortunately there is no effective synchronization criterion for pinning synchronization of complex dynamical networks with switching topology. In this paper, pinning synchronization of complex dynamical networks with switching topology is studied. Two basic problems are considered: one is pinning synchronization of switched complex networks under arbitrary switching; the other is pinning synchronization of switched complex networks by design of switching when synchronization cannot achieved by using any individual connection topology alone. For the two problems, common Lyapunov function method and single Lyapunov function method are used respectively, some global synchronization criteria are proposed and the designed switching law is given. Finally, simulation results verify the validity of the results.

  17. Flux pinning in superconductors. 2. ed.

    Energy Technology Data Exchange (ETDEWEB)

    Matsushita, Teruo [Kyushu Institute of Technology, Iizuka, Fukuoka (Japan). Dept. of Computer Science and Electronics

    2014-04-01

    Ideal for graduate students studying superconductivity and experts alike. Written by a researcher with more than 30 years experience in the field. All chapters are completely revised. The book covers the flux pinning mechanisms and properties and the electromagnetic phenomena caused by the flux pinning common for metallic, high-Tc and MgB2 superconductors. The condensation energy interaction known for normal precipitates or grain boundaries and the kinetic energy interaction proposed for artificial Nb pins in Nb-Ti, etc., are introduced for the pinning mechanism. Summation theories to derive the critical current density are discussed in detail. Irreversible magnetization and AC loss caused by the flux pinning are also discussed. The loss originally stems from the ohmic dissipation of normal electrons in the normal core driven by the electric field induced by the flux motion. The readers will learn why the resultant loss is of hysteresis type in spite of such mechanism. The influence of the flux pinning on the vortex phase diagram in high Tc superconductors is discussed, and the dependencies of the irreversibility field are also described on other quantities such as anisotropy of superconductor, specimen size and electric field strength. Recent developments of critical current properties in various high-Tc superconductors and MgB2 are introduced. Other topics are: singularity in the case of transport current in a parallel magnetic field such as deviation from the Josephson relation, reversible flux motion inside pinning potentials which causes deviation from the critical state model prediction, the concept of the minimization of energy dissipation in the flux pinning phenomena which gives the basis for the critical state model, etc. Significant reduction in the AC loss in AC wires with very fine filaments originates from the reversible flux motion which is dominant in the two-dimensional pinning. The concept of minimum energy dissipation explains also the behavior

  18. Anisotropic flux pinning in high Tc superconductors

    Science.gov (United States)

    Koleśnik, S.; Igalson, J.; Skośkiewicz, T.; Szymczak, R.; Baran, M.; Pytel, K.; Pytel, B.

    1995-02-01

    In this paper we present a comparison of the results of FC magnetization measurements on several PbSr(Y,Ca)CuO crystals representing various levels of flux pinning. The pinning centers in our crystals have been set up during the crystal growth process or introduced by neutron irradiation. Some possible explanations of the observed effects, including surface barrier, flux-center distribution and sample-shape effects, are discussed.

  19. Open safety pin in the nasal cavity.

    Science.gov (United States)

    Sen, I; Sikder, B; Sinha, R; Paul, R

    2004-04-01

    Foreign bodies in the nasal cavity are common-day occurrences in Otolaryngologic practice. But an open safety pin in nose with it' s sharp end directed towards roof is a rare incidence, and available literature is silent about this presentation; it is probably, the first of it' s kind being reported. Two cases of safety pins inside the nasal cavity, one open and the other closed, have been presented here with a brief review of literature.

  20. Open safety pin in the nasal cavity

    OpenAIRE

    Sen, I; Sikder, B.; R. Sinha; Paul, R

    2004-01-01

    Foreign bodies in the nasal cavity are common-day occurrences in Otolaryngologic practice. But an open safety pin in nose with it’ s sharp end directed towards roof is a rare incidence, and available literature is silent about this presentation; it is probably, the first of it’ s kind being reported. Two cases of safety pins inside the nasal cavity, one open and the other closed, have been presented here with a brief review of literature.

  1. IMp: The customizable LEGO® Pinned Insect Manipulator

    Directory of Open Access Journals (Sweden)

    Steen Dupont

    2015-02-01

    Full Text Available We present a pinned insect manipulator (IMp constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble.

  2. Memory-only selection of dictionary PINs

    OpenAIRE

    Stanek, Martin

    2014-01-01

    We estimate the security of dictionary-based PINs (Personal Identification Numbers) that a user selects from his/her memory without any additional aids. The estimates take into account the distribution of words in source language. We use established security metrics, such as entropy, guesswork, marginal guesswork and marginal success rate. The metrics are evaluated for various scenarios -- aimed at improving the security of the produced PINs. In general, plain and straightforward construction...

  3. The pinning effect in quantum dots

    Energy Technology Data Exchange (ETDEWEB)

    Monisha, P. J., E-mail: pjmonisha@gmail.com [School of Physics, University of Hyderabad, Hyderabad-500046 (India); Mukhopadhyay, Soma [Department of Physics, D V R College of Engineering and Technology, Hyderabad-502285 (India)

    2014-04-24

    The pinning effect is studied in a Gaussian quantum dot using the improved Wigner-Brillouin perturbation theory (IWBPT) in the presence of electron-phonon interaction. The electron ground state plus one phonon state is degenerate with the electron in the first excited state. The electron-phonon interaction lifts the degeneracy and the first excited states get pinned to the ground state plus one phonon state as we increase the confinement frequency.

  4. Study on contact pressure at pin connection detail; Pin setsugobu no sesshokuatsu ni taisuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Miki, C.; Anami, K. [Tokyo Institute of Technology, Tokyo (Japan); Suzuki, M. [Ministry of Construction, Tokyo (Japan); Ohashi, H. [Honshu-Shikoku Bridge Authority, Tokyo (Japan)

    1997-07-21

    Contact pressure between pin and pin plate is discussed by FEM and UT from the point of view of the connection detail of hanger lope of long span suspension bridge. Application of the UT to the 25S surface specimen (and smoother surface) is effective. The results of UT and FEM distribution of contact pressure near the center of plate almost agree with the Hertz law. However near the surface of pin plate the contact pressure and plate width of large contact pressure region increase larger than those near contact pressure and plate width of large contact pressure region increase larger than those near center of pin plate. 12 refs., 17 figs.

  5. Improved pinning by multiple in-line damage

    Energy Technology Data Exchange (ETDEWEB)

    Weinstein, Roy [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Sawh, Ravi-Persad [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Gandini, Alberto [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Parks, Drew [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States)

    2005-02-01

    Columnar pinning centres provide the largest pinning potential, U{sub pin}, but not the greatest J{sub c} or pinnable field, B{sub pin}. Characteristics of ion-generated columnar defects which limit J{sub c} and B{sub pin} are discussed, including reduction of the percolation path, and the need for a larger number of columns of damage, for pinning, than are usually estimated. It is concluded that columnar pinning centres limit B{sub pin} to less than 4 T, and also severely reduce J{sub c}. The goal of maximizing U{sub pin}, via columnar centres, appears to have obscured a more rewarding approach and resulted in neglect of a large regime of ion interactions. Evidence is reviewed that multiple in-line damage (MILD), described herein, can provide orders of magnitude higher J{sub c} and B{sub pin}, despite providing lower U{sub pin}. The MILD pinning centre morphology is discussed, and it is estimated that for present-day large grain high T{sub c} superconductors, a J{sub c} value of {approx}10{sup 6}Acm{sup -2} is obtainable at 77 K, even when crystal plane alignment and weak links are not improved. In addition, the pinned field is increased by over an order of magnitude. An experiment is proposed to confirm these calculations, directly compare MILD pinning to continuous columnar pinning, and determine the optimum MILD structure. Applications of MILD pinning are discussed.

  6. Melt layer erosion of metallic armour targets during off-normal events in tokamaks

    Science.gov (United States)

    Bazylev, B.; Wuerz, H.

    2002-12-01

    Melt layer erosion by melt motion is the dominating erosion mechanism for metallic armours under high heat loads. A 1-D fluid dynamics simulation model for calculation of melt motion was developed and validated against experimental results for tungsten from the e-beam facility JEBIS and beryllium from the e-beam facility JUDITH. The driving force in each case is the gradient of the surface tension. Due to the high velocity which develops in the Be melt considerable droplet splashing occurs.

  7. A Modeling Approach to Fiber Fracture in Melt Impregnation

    Science.gov (United States)

    Ren, Feng; Zhang, Cong; Yu, Yang; Xin, Chunling; Tang, Ke; He, Yadong

    2017-02-01

    The effect of process variables such as roving pulling speed, melt temperature and number of pins on the fiber fracture during the processing of thermoplastic based composites was investigated in this study. The melt impregnation was used in this process of continuous glass fiber reinforced thermoplastic composites. Previous investigators have suggested a variety of models for melt impregnation, while comparatively little effort has been spent on modeling the fiber fracture caused by the viscous resin. Herein, a mathematical model was developed for impregnation process to predict the fiber fracture rate and describe the experimental results with the Weibull intensity distribution function. The optimal parameters of this process were obtained by orthogonal experiment. The results suggest that the fiber fracture is caused by viscous shear stress on fiber bundle in melt impregnation mold when pulling the fiber bundle.

  8. Melting of Transition Metals

    Energy Technology Data Exchange (ETDEWEB)

    Ross, M; Japel, S; Boehler, R

    2005-04-11

    We review the transition melting studies carried out at Mainz, and describe a recently developed model used to explain that the relatively low melting slopes are due to the partially filled d-bands, and the persistence of the pressure induced s-d transition. The basic tenets of the model have now been reconfirmed by new measurements for Cu and Ni. The measurements show that Cu which has a filled 3d-band, has a melt slope that is about 2.5 greater than its neighbor Ni. In the case of Mo, the apparent discrepancy of DAC melting measurements with shock melting can be explained by accounting for the change in melt slope due to the bcc-cp transition observed in the shock studies. The Fe melt curve is revisited. The possible relevance of the Jahn-Teller effect and recently observed transition metal melts with Icosahedral Short-Range Order (ISRO) is discussed.

  9. Performance comparison of pin fin in-duct flow arrays with various pin cross-sections

    Energy Technology Data Exchange (ETDEWEB)

    Sahiti, N. [LSTM-Erlangen, Institute of Fluid Mechanics, Friedrich-Alexander-University, Erlangen-Nuremberg, Cauerstr. 4, D-91058 Erlangen (Germany)]. E-mail: sahiti@lstm.uni-erlangen.de; Lemouedda, A. [Department of Process Engineering, Georg-Simon-Ohm University of Applied Sciences, Wassertorstr. 10, D-90489 Nuremberg (Germany); Stojkovic, D. [LSTM-Erlangen, Institute of Fluid Mechanics, Friedrich-Alexander-University, Erlangen-Nuremberg, Cauerstr. 4, D-91058 Erlangen (Germany); Durst, F. [LSTM-Erlangen, Institute of Fluid Mechanics, Friedrich-Alexander-University, Erlangen-Nuremberg, Cauerstr. 4, D-91058 Erlangen (Germany); Franz, E. [Department of Process Engineering, Georg-Simon-Ohm University of Applied Sciences, Wassertorstr. 10, D-90489 Nuremberg (Germany)

    2006-08-15

    Pin fin arrays are frequently used for cooling of high thermal loaded electronic components. Whereas the pin fin accomplishment regarding heat transfer is always higher than that of other fin configurations, the high pressure drop accompanying pins seriously reduces their overall performance. In order to check how the form of pin cross-section influences the pressure drop and heat transfer capabilities, six forms of pin cross-section were numerically investigated. By employing the conjugate heat transfer boundary conditions, numerical simulations close to realistic working conditions were performed. Two geometric comparison criteria were applied so that the conclusions derived from numerical computations were valid for various possible geometric parameters and working conditions. Both staggered and inline pin arrangements were investigated as these are common in practical applications. The heat transfer and pressure drop characteristics are presented in terms of appropriate dimensionless variables. The final judgment of the performance of the pin fin cross-section was performed based on the heat exchanger performance plot. Such a plot allows the assessment of the pin performance including their heat transfer and the pressure drop.

  10. Design of a terahertz CW photomixer based on PIN and superlattice PIN devices

    DEFF Research Database (Denmark)

    Krozer, Viktor; Eichhorn, Finn

    2006-01-01

    We present the design of a photomixer LO based on standard and superlattice PIN diodes, operating at 1 THz. The design is based on a direct integration of a double slot antenna with the PIN device and a suitable matching circuit. The antenna has been designed together with a dielectric lens using...

  11. Dynamics and Stability of Pinned-Clamped and Clamped-Pinned Cylindrical Shells Conveying Fluid

    Science.gov (United States)

    Misra, A. K.; Wong, S. S. T.; Païdoussis, M. P.

    2001-11-01

    The paper examines the dynamics and stability of fluid-conveying cylindrical shells having pinned-clamped or clamped-pinned boundary conditions, where ``pinned'' is an abbreviation for ``simply supported''. Flügge's equations are used to describe the shell motion, while the fluid-dynamic perturbation pressure is obtained utilizing the linearized potential flow theory. The solution is obtained using two methods - the travelling wave method and the Fourier-transform approach. The results obtained by both methods suggest that the negative damping of the clamped-pinned systems and positive damping of the pinned-clamped systems, observed by previous investigators for any arbitrarily small flow velocity, are simply numerical artefacts; this is reinforced by energy considerations, in which the work done by the fluid on the shell is shown to be zero. Hence, it is concluded that both systems are conservative.

  12. Potential of pin-by-pin SPN calculations as an industrial reference

    Energy Technology Data Exchange (ETDEWEB)

    Fliscounakis, M.; Girardi, E.; Courau, T.; Couyras, D. [EDF R and D/Sinetics, 1 av du General de Gaulle, F92141 Clamart Cedex (France)

    2012-07-01

    This paper aims at analysing the potential of pin-by-pin SP{sub n} calculations to compute the neutronic flux in PWR cores as an alternative to the diffusion approximation. As far as pin-by-pin calculations are concerned, a SPH equivalence is used to preserve the reactions rates. The use of SPH equivalence is a common practice in core diffusion calculations. In this paper, a methodology to generalize the equivalence procedure in the SP{sub n} equations context is presented. In order to verify and validate the equivalence procedure, SP{sub n} calculations are compared to 2D transport reference results obtained with the APOLL02 code. The validation cases consist in 3x3 analytical assembly color sets involving burn-up heterogeneities, UOX/MOX interfaces, and control rods. Considering various energy discretizations (up to 26 groups) and flux development orders (up to 7) for the SP{sub n} equations, results show that 26-group SP{sub 3} calculations are very close to the transport reference (with pin production rates discrepancies < 1%). This proves the high interest of pin-by-pin SP{sub n} calculations as an industrial reference when relying on 26 energy groups combined with SP{sub 3} flux development order. Additionally, the SP{sub n} results are compared to diffusion pin-by-pin calculations, in order to evaluate the potential benefit of using a SP{sub n} solver as an alternative to diffusion. Discrepancies on pin-production rates are less than 1.6% for 6-group SP{sub 3} calculations against 3.2% for 2-group diffusion calculations. This shows that SP{sub n} solvers may be considered as an alternative to multigroup diffusion. (authors)

  13. A double tuned rail damper—increased damping at the two first pinned-pinned frequencies

    Science.gov (United States)

    Maes, J.; Sol, H.

    2003-10-01

    Railway-induced vibrations are a growing matter of environmental concern. The rapid development of transportation, the increase of vehicle speeds and vehicle weights have resulted in higher vibration levels. In the meantime vibrations that were tolerated in the past are now considered to be a nuisance. Numerous solutions have been proposed to remedy these problems. The majority only acts on a specific part of the dynamic behaviour of the track. This paper presents a possible solution to reduce the noise generated by the 'pinned-pinned' frequencies. Pinned-pinned frequencies correspond with standing waves whose nodes are positioned exactly at the sleeper supports. The two first pinned-pinned frequencies are situated approximately at 950 and 2200 Hz (UIC60-rail and sleeper spacing of 0.60 m). To attenuate these vibrations, the Department of MEMC at the VUB has developed a dynamic vibration absorber called the Double Tuned Rail Damper (DTRD). The DTRD is mounted between two sleepers on the rail and is powered by the motion of the rail. The DTRD consists of two major parts: a steel plate which is connected to the rail with an interface of an elastic layer, and a rubber mass. The two first resonance frequencies of the steel plate coincide with the targeted pinned-pinned frequencies of the rail. The rubber mass acts as a motion controller and energy absorber. Measurements at a test track of the French railway company (SNCF) have shown considerable attenuation of the envisaged pinned-pinned frequencies. The attenuation rate surpasses 5 dB/m at certain frequency bands.

  14. Statistics of dislocation pinning at localized obstacles

    Energy Technology Data Exchange (ETDEWEB)

    Dutta, A. [S. N. Bose National Centre for Basic Sciences, Salt Lake, Kolkata 700098 (India); Bhattacharya, M., E-mail: mishreyee@vecc.gov.in; Barat, P. [Variable Energy Cyclotron Centre, 1/AF Bidhannagar, Kolkata 700064 (India)

    2014-10-14

    Pinning of dislocations at nanosized obstacles like precipitates, voids, and bubbles is a crucial mechanism in the context of phenomena like hardening and creep. The interaction between such an obstacle and a dislocation is often studied at fundamental level by means of analytical tools, atomistic simulations, and finite element methods. Nevertheless, the information extracted from such studies cannot be utilized to its maximum extent on account of insufficient information about the underlying statistics of this process comprising a large number of dislocations and obstacles in a system. Here, we propose a new statistical approach, where the statistics of pinning of dislocations by idealized spherical obstacles is explored by taking into account the generalized size-distribution of the obstacles along with the dislocation density within a three-dimensional framework. Starting with a minimal set of material parameters, the framework employs the method of geometrical statistics with a few simple assumptions compatible with the real physical scenario. The application of this approach, in combination with the knowledge of fundamental dislocation-obstacle interactions, has successfully been demonstrated for dislocation pinning at nanovoids in neutron irradiated type 316-stainless steel in regard to the non-conservative motion of dislocations. An interesting phenomenon of transition from rare pinning to multiple pinning regimes with increasing irradiation temperature is revealed.

  15. Radon measurements with a PIN photodiode

    Energy Technology Data Exchange (ETDEWEB)

    Martin-Martin, A. [Laboratorio de Investigacion en Baja Radiactividad (LIBRA), Edificio I-D, Campus Miguel Delibes, Universidad de Valladolid, Valladolid 47011 (Spain) and Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, Valladolid 47011 (Spain)]. E-mail: alonsomm@libra.uva.es; Gutierrez-Villanueva, J.L. [Laboratorio de Investigacion en Baja Radiactividad (LIBRA), Edificio I-D, Campus Miguel Delibes, Universidad de Valladolid, Valladolid 47011 (Spain); Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, Valladolid 47011 (Spain); Munoz, J.M. [Departamento de Electricidad y Electronica, Universidad de Valladolid, Valladolid 47011 (Spain); Garcia-Talavera, M. [Laboratorio de Investigacion en Baja Radiactividad (LIBRA), Edificio I-D, Campus Miguel Delibes, Universidad de Valladolid, Valladolid 47011 (Spain); Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, Valladolid 47011 (Spain); Adamiec, G. [Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, Valladolid 47011 (Spain); Iniguez, M.P. [Departamento de Fisica Teorica, Atomica y Optica, Universidad de Valladolid, Valladolid 47011 (Spain)

    2006-10-15

    Silicon photodiodes are well suited to detect alphas coming from different sources as neutron reactions or radon daughters. In this work a radon in air detecting device, using an 18x18 mm silicon PIN photodiode is studied. The ionized airborne decay products formed during radon diffusion were focused by an accelerating high voltage to the PIN surface. Several conducting rings were disposed inside a cylindrical PVC vessel in such a way that they reproduced the electric field created by a punctual charge located behind PIN position. Alpha spectra coming from the neutral and ionized species deposited on the PIN surface, dominated by {sup 218}Po and {sup 214}Po progeny peaks, were recorded for varying conditions. Those include radon concentration from a Pylon source, high voltage (thousands of volts) and PIN inverse bias voltage. Different parameters such as temperature and humidity were also registered during data acquisition. The increase in the particle collection efficiency with respect to zero electric field was compared with the corresponding to a parallel plates configuration. A discussion is made in terms of the most appropriate voltages for different radon concentrations.

  16. The effect of temperature on pinning mechanisms in HTS composites

    Science.gov (United States)

    Sotnikova, A. P.; Rudnev, I. A.

    2016-09-01

    Pinning mechanism in samples of second generation tapes (2G) of high-temperature superconductors (HTS) was studied The critical current and the pinning force were calculated from the magnetization curves measured in the temperature range of 4.2 - 77 K in magnetic fields up to 14 Tesla using vibration sample magnetometer. To determine the pinning mechanism the dependences of pinning force on magnetic field were constructed according to the Dew-Hughes model and Kramer's rule. The obtained dependences revealed a significant influence of the temperature on effectiveness of different types of pinning. At low temperatures the 2G HTS tapes of different manufacturers demonstrated an equal efficiency of the pinning centers but with temperature increase the differences in pinning mechanisms as well as in properties and effectiveness of the pinning centers become obvious. The influence of the pinning mechanism on the energy losses in HTS tapes was shown.

  17. Termination of pinned spirals by local stimuli

    Science.gov (United States)

    Chen, Jiang-Xing; Guo, Ming-Ming; Ma, Jun

    2016-02-01

    The termination of pinned spirals on a defect by means of local stimuli is studied. On a completely unexcitable defect, the elimination process is discussed and its corresponding mechanism is presented. Especially, the mechanism of unpinning spirals on a partially unexcitable defect, which has not been investigated so far, is explored. With fixed pacing frequency ω L , there exists a maximal radius R max above which the pinned spiral cannot be removed. It is found that the value of R max does not increase as ω L in a dynamical regime, forming a platform in the R\\textit{max}\\text-ωL curves. Based on analyzing the dispersion relation on the spiral tip around the obstacle, the underlying mechanism is clarified. Also, it is found that when multiple spirals are pinned, the value of R max decreases on a partially unexcitable defect while the change is very slight on a completely unexcitable one.

  18. Pin solar cells made of amorphous silicon

    Science.gov (United States)

    Plaettner, R. D.; Kruehler, W. W.

    Investigations leading to solar cells with a structure SnO2-pin and an efficiency up to 9.8% are reviewed. The production of large-surface metal/pin/transparent conductive oxide (TCO)-solar cells is discussed. A two-chamber reactor, grid structure and tinning of cells, and an a-Si-module are described. The production of glass/TCO/pin/metal-solar cells and a-SiGe:H-compounds is outlined. Measurements on solar cells and diodes including the efficiency of a-Si:H-solar cells, spectral sensitivity, diffusion lengths, field effect measurements, and modifications of solar cells (space-charge limited currents, reduction of solar cells aging) are treated.

  19. Effective pinning energy landscape perturbations for propagating magnetic domain walls

    Science.gov (United States)

    Burn, D. M.; Atkinson, D.

    2016-01-01

    The interaction between a magnetic domain wall and a pinning site is explored in a planar nanowire using micromagnetics to reveal perturbations of the pinning energetics for propagating domain walls. Numerical simulations in the high damping ’quasi-static’ and low damping ’dynamic’ regimes are compared and show clear differences in de-pinning fields, indicating that dynamical micromagnetic models, which incorporate precessionally limited magnetization processes, are needed to understand domain wall pinning. Differences in the micromagnetic domain wall structure strongly influence the pinning and show periodic behaviour with increasing applied field associated with Walker breakdown. In the propagating regime pinning is complicated. PMID:27694953

  20. Broken safety pin in bronchus - Anaesthetic considerations

    Directory of Open Access Journals (Sweden)

    Roona Shad

    2012-01-01

    Full Text Available Safety pins are not commonly aspirated objects in infants and form only a small fraction of all the metallic foreign body (FB which accounts for 4.4% of all foreign bodies found in tracheobronchial tree. Bronchoscopy procedure has various complications, in addition to failure to remove FB due to its impaction, especially with metallic pointed objects ending up in open surgical removal. Infant with inhaled foreign body are always a challenge to anaesthetist. We had one such case of broken safety pin impacted in the wall of right bronchus of an infant with failure to remove on repeated attempts at rigid bronchoscopy.

  1. Broken safety pin in bronchus - Anaesthetic considerations.

    Science.gov (United States)

    Shad, Roona; Agarwal, Aditya

    2012-11-01

    Safety pins are not commonly aspirated objects in infants and form only a small fraction of all the metallic foreign body (FB) which accounts for 4.4% of all foreign bodies found in tracheobronchial tree. Bronchoscopy procedure has various complications, in addition to failure to remove FB due to its impaction, especially with metallic pointed objects ending up in open surgical removal. Infant with inhaled foreign body are always a challenge to anaesthetist. We had one such case of broken safety pin impacted in the wall of right bronchus of an infant with failure to remove on repeated attempts at rigid bronchoscopy.

  2. Self-Pinning on a Liquid Surface.

    Science.gov (United States)

    Antoine, C; Irvoas, J; Schwarzenberger, K; Eckert, K; Wodlei, F; Pimienta, V

    2016-02-04

    We report on the first experimental evidence of a self-pinning liquid drop on a liquid surface. This particular regime is observed for a miscible heavier oil drop (dichloromethane) deposited on an aqueous solution laden by an ionic surfactant (hexadecyltrimethylammonium bromide). Experimental characterization of the drop shape evolution coupled to particle image velocimetry points to the correlation between the drop profile and the accompanying flow field. A simple model shows that the observed pinned stage is the result of a subtle competition between oil dissolution and surfactant adsorption.

  3. New types of high field pinning centers and pinning centers for the peak effect

    Science.gov (United States)

    Gajda, Daniel; Zaleski, Andrzej; Morawski, Andrzej; Hossain, Md Shahriar A.

    2017-08-01

    In this article, we report the results of a study that shows the existence of pinning centers inside grains and between grains in NbTi wires. We accurately show the ranges of magnetic fields in which the individual pinning centers operate. The pinning centers inside grains are activated in high magnetic fields above 6 T. We show the range of magnetic fields in which individual defects, dislocations, precipitates inside grains and substitutions in the crystal lattice can operate. We show the existence of a new kind of high field pinning center, which operates in high magnetic fields from 8 to ˜9.5 T. We indicate that dislocations create pinning centers in the range of magnetic fields from 6 to 8 T. In addition, our measurements suggest that the peak effect (increased critical current density (J c) near the upper critical field (B c2)) could be attributed to martensitic (needle-shaped) α‧-Ti inclusions inside grains. These centers are very important because they work very effectively in magnetic fields above 9.5-10 T. We also show that the α-Ti precipitates (between grains) with a thickness similar to the coherence length create pinning centers which work very effectively in magnetic fields from 3 to 6 T. In magnetic fields below 3 T, they act very efficiently in grain boundaries. The measurements indicate that the pinning centers created by dislocations only can be tested by transport measurements. This indicates that dislocations do not increase the magnetic critical current density (J cm). Cold drawing improves pinning centers at grain boundaries and increases the dislocation density, and cold-drawing pinning centers are responsible for the peak effect.

  4. Effect of the number of pins and inter-pin distance on somatosensory evoked magnetic fields following mechanical tactile stimulation.

    Science.gov (United States)

    Onishi, Hideaki; Sugawara, Kazuhiro; Yamashiro, Koya; Sato, Daisuke; Suzuki, Makoto; Kirimoto, Hikari; Tamaki, Hiroyuki; Murakami, Hiroatsu; Kameyama, Shigeki

    2013-10-16

    Magnetoencephalography (MEG) recordings were collected to investigate the effect of the number of mechanical pins and inter-pin distance on somatosensory evoked magnetic fields (SEFs) following mechanical stimulation (MS). We used a 306-ch whole-head MEG system. SEFs were elicited through tactile stimuli with 1-, 2-, 3-, 4- and 8-pins using healthy participants. Tactile stimuli were applied to the tip of the right index finger. SEF following electrical stimulation of the index finger was recorded in order to compare the activity in the primary somatosensory cortex (S1) following MS. Prominent SEFs were recorded from the contralateral hemisphere approximately 54 ms (P50m) and 125 ms (P100m) after MS regardless of the number of pins. Equivalent current dipoles were located in the S1. The source activities for P50m and P100m significantly increased in tandem with the number of pins for MS. However, the increased ratios for the source activities according to the increase in the number of pins were significantly smaller than that induced by electrical stimulation, and when the number of the pins doubled from 1-pin to 2-pins, from 2-pins to 4-pins, and from 4-pins to 8-pins, S1 activities increased by only 130%. Additionally, source activities significantly increased when the inter-pin distance increased from 2.4 to 7.2 mm. The number of stimulated receptors was considered to have increased with an increase in the inter-pin distance as well as an increase in the number of pins. These findings clarified the effect of the number of pins and inter-pin distance for MS on SEFs.

  5. Scratch Hardness and Wear Performance of Laser-Melted Steels : Effects of Anisotropy

    NARCIS (Netherlands)

    Beurs, H. de; Minholts, G.; Hosson, J.Th.M. De

    1989-01-01

    Effects of the orientation of dendrites on the scratch hardness and wear performance of laser-melted steels have been investigated. Scratch experiments have been carried out with a Vickers indenter and wear experiments with a pin-on-disk tester. The deformed structure is investigated, using transmis

  6. A pinned polymer model of posture control

    CERN Document Server

    Chow, C C; Chow, Carson C; Collins, J J

    1995-01-01

    A phenomenological model of human posture control is posited. The dynamics are modelled as an elastically pinned polymer under the influence of noise. The model accurately reproduces the two-point correlation functions of experimental posture data and makes predictions for the response function of the postural control system. The physiological and clinical significance of the model is discussed.

  7. Duodenocolic fistula due to safety pin ingestion.

    Science.gov (United States)

    Cay, Ali; Imamoğlu, Mustafa; Sarihan, Haluk; Sayil, Ozgür

    2004-01-01

    The authors describe the case of a 16-month-old boy with benign duodenocolic fistula due to safety pin ingestion who presented with abdominal pain, diarrhea and weight loss. Etiology, symptomatology, diagnosis and management are discussed and the literature is reviewed. Early diagnosis and surgical management are necessary to avoid serious morbidity.

  8. Turban pin aspiration: new fashion, new syndrome.

    Science.gov (United States)

    Ilan, Ophir; Eliashar, Ron; Hirshoren, Nir; Hamdan, Kasem; Gross, Menachem

    2012-04-01

    Turban pin aspiration syndrome is a new clinical entity afflicting young Islamic girls wearing a turban.The goal of this study was to present our experience in diagnosis and treatment of this new entity, define its clinical and epidemiologic features, and shed a new light on the role of fashion in the increased incidence. A retrospective study in a tertiary university hospital. Review of clinical parameters and epidemiologic features of 26 patients diagnosed with turban pin aspiration syndrome admitted to the Hadassah-Hebrew University Hospitals in Jerusalem from 1990 to 2010. All patients were Muslim females with an average age of 16 years. In all cases, the history was positive for accidental aspiration. Most of the pins were located in the trachea (42%). In 20 cases, the pins were extracted by rigid bronchoscopy without major complications. Fluoroscopy-assisted rigid bronchoscopy was used successfully in three cases. In one case, the object was self-ejected by coughing before the bronchoscopy, and two patients were referred to the chest unit for thoracotomy. Clinicians should be aware of this distinct form of foreign body aspiration, its method of diagnosis, and extraction techniques. A cultural investigation showed a difference in the turban-fastening technique of young girls as compared with their mothers. Removal by rigid bronchoscopy is a safe method with a high success rate and should be considered as the preferred extraction method of choice. Copyright © 2012 The American Laryngological, Rhinological, and Otological Society, Inc.

  9. Pinning control of clustered complex networks with different size

    Science.gov (United States)

    Fu, Chenbo; Wang, Jinbao; Xiang, Yun; Wu, Zhefu; Yu, Li; Xuan, Qi

    2017-08-01

    In pinning control of complex networks, it is found that, with the same pinning effort, the network can be better controlled by pinning the large-degree nodes. But in the clustered complex networks, this preferential pinning (PP) strategy is losing its effectiveness. In this paper, we demonstrate that in the clustered complex networks, especially when the clusters have different size, the random pinning (RP) strategy performs much better than the PP strategy. Then, we propose a new pinning strategy based on cluster degree. It is revealed that the new cluster pinning strategy behaves better than RP strategy when there are only a smaller number of pinning nodes. The mechanism is studied by using eigenvalue and eigenvector analysis, and the simulations of coupled chaotic oscillators are given to verify the theoretical results. These findings could be beneficial for the design of control schemes in some practical systems.

  10. Preparation of high-quality HTS rings for application in the magnetic bearing of cryotanks and pinning in grain boundaries

    Science.gov (United States)

    Bringmann, B.; Walter, H.; Jooss, Ch.; Leenders, A.; Freyhardt, H. C.

    2002-08-01

    Seeded melt growth of YBCO high-temperature superconductors is one of the most promising preparation techniques to obtain high-quality HTS tiles for application, e.g. in magnetic bearings. Semi-finished HTSL products of complex shapes have to be developed by different seeding and multi-seeding techniques. To obtain large hollow cylinders designed for application in the magnetic bearing of a cryotank a modified multi-seeded melt growth (MSMG) process was employed. This cryotank will be mounted for testing in a vehicle of a major German car manufacturer. The MSMG process introduces grain boundaries into the HTS tiles. For transport current investigations of [0 0 1]-tilt grain boundaries in melt textured YBCO a series of MSMG bicrystals have been prepared. They exhibit a dependence of the critical current density on misorientation angle which is much weaker than the one observed in thin-film bicrystals. The bulk samples have dimensions larger than the magnetic penetration depth along the grain boundary. Thus, flux pinning has to be taken into account. Different contributions to the longitudinal pinning force have to be considered: vortices at grain boundaries can be pinned by magnetic interaction with Abrikosov vortices in the banks, by defects in the grain boundary itself or by defects which are located next to the grain boundary.

  11. Analytical method for reconstruction pin to pin of the nuclear power density distribution

    Energy Technology Data Exchange (ETDEWEB)

    Pessoa, Paulo O.; Silva, Fernando C.; Martinez, Aquilino S., E-mail: ppessoa@con.ufrj.br, E-mail: fernando@con.ufrj.br, E-mail: aquilino@imp.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil)

    2013-07-01

    An accurate and efficient method for reconstructing pin to pin of the nuclear power density distribution, involving the analytical solution of the diffusion equation for two-dimensional neutron energy groups in homogeneous nodes, is presented. The boundary conditions used for analytic as solution are the four currents or fluxes on the surface of the node, which are obtained by Nodal Expansion Method (known as NEM) and four fluxes at the vertices of a node calculated using the finite difference method. The analytical solution found is the homogeneous distribution of neutron flux. Detailed distributions pin to pin inside a fuel assembly are estimated by the product of homogeneous flux distribution by local heterogeneous form function. Furthermore, the form functions of flux and power are used. The results obtained with this method have a good accuracy when compared with reference values. (author)

  12. Pinning control of complex networked systems synchronization, consensus and flocking of networked systems via pinning

    CERN Document Server

    Su, Housheng

    2013-01-01

    Synchronization, consensus and flocking are ubiquitous requirements in networked systems. Pinning Control of Complex Networked Systems investigates these requirements by using the pinning control strategy, which aims to control the whole dynamical network with huge numbers of nodes by imposing controllers for only a fraction of the nodes. As the direct control of every node in a dynamical network with huge numbers of nodes might be impossible or unnecessary, it’s then very important to use the pinning control strategy for the synchronization of complex dynamical networks. The research on pinning control strategy in consensus and flocking of multi-agent systems can not only help us to better understand the mechanisms of natural collective phenomena, but also benefit applications in mobile sensor/robot networks. This book offers a valuable resource for researchers and engineers working in the fields of control theory and control engineering.   Housheng Su is an Associate Professor at the Department of Contro...

  13. Auxin transport through PIN-FORMED 3 (PIN3) controls shade avoidance and fitness during competition

    Science.gov (United States)

    Keuskamp, Diederik H.; Pollmann, Stephan; Voesenek, Laurentius A. C. J.; Peeters, Anton J. M.; Pierik, Ronald

    2010-01-01

    Plants grow in dense vegetations at the risk of being out-competed by neighbors. To increase their competitive power, plants display adaptive responses, such as rapid shoot elongation (shade avoidance) to consolidate light capture. These responses are induced upon detection of proximate neighbors through perception of the reduced ratio between red (R) and far-red (FR) light that is typical for dense vegetations. The plant hormone auxin is a central regulator of plant development and plasticity, but until now it has been unknown how auxin transport is controlled to regulate shade-avoidance responses. Here, we show that low R:FR detection changes the cellular location of the PIN-FORMED 3 (PIN3) protein, a regulator of auxin efflux, in Arabidopsis seedlings. As a result, auxin levels in the elongating hypocotyls are increased under low R:FR. Seedlings of the pin3-3 mutant lack this low R:FR-induced increase of endogenous auxin in the hypocotyl and, accordingly, have no elongation response to low R:FR. We hypothesize that low R:FR-induced stimulation of auxin biosynthesis drives the regulation of PIN3, thus allowing shade avoidance to occur. The adaptive significance of PIN3-mediated control of shade-avoidance is shown in plant competition studies. It was found that pin3 mutants are outcompeted by wild-type neighbors who suppress fitness of pin3-3 by 40%. We conclude that low R:FR modulates the auxin distribution by a change in the cellular location of PIN3, and that this control can be of great importance for plants growing in dense vegetations. PMID:21149713

  14. Lessons learnt from FARO/TERMOS corium melt quenching experiments

    Energy Technology Data Exchange (ETDEWEB)

    Magallon, D.; Huhtiniemi, I.; Hohmann, H. [Commission of the European Communities, Ispra (Italy). Joint Research Center

    1998-01-01

    The influence of melt quantity, melt composition, water depth and initial pressure on quenching is assessed on the basis of seven tests performed in various conditions in the TERMOS vessel of the FARO facility at JRC-Ispra. Tests involved UO{sub 2}-based melt quantities in the range 18-176 kg at a temperature of approximately 3000 K poured into saturated water. The results suggest that erosion of the melt jet column is an efficient contributor to the amount of break-up, and thus quenching, for large pours of corium melt. The presence of Zr metal in the melt induced a much more efficient quenching than in a similar test with no Zr metal, attributed to the oxidation of the Zr. Significant amounts of H{sub 2} were produced also in tests with pure oxidic melts (e.g. about 300 g for 157 kg melt). In the tests at 5.0 and 2.0 MPa good mixing with significant melt break-up and quenching was obtained during the penetration in the water. At 0.5 MPa, good penetration of the melt into the water could still be achieved, but a jump in the vessel pressurisation occurred when the melt contacted the bottom and part (5 kg) of the debris was re-ejected from the water. (author)

  15. Optimization study on pin tip diameter of an impact-pin nozzle at high pressure ratio

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, C. Palani; Lee, Kwon Hee [FMTRC, Daejoo Machinery Co. Ltd., Daegu (Korea, Republic of); Park, Tae Choon; Cha, Bong Jun [Engine Components Research Team, Korea Aerospace Research Institute, Daejeon (Korea, Republic of); Kim, Heuy Dong [Dept. of Mechanical Engineering, Andong National University, Andong (Korea, Republic of)

    2016-09-15

    Wet compression system is typically installed in a gas turbine engine to increase the net power output and efficiency. A crucial component of the wet compression system is the nozzle which generates fine water droplets for injection into the compressor. The main objective of present work is to optimize a kind of nozzle called impact-pin spray nozzle and thereby produce better quality droplets. To achieve this, the dynamics occurring in the water jet impinging on the pin tip, the subsequent formation of water sheet, which finally breaks into water droplets, must be studied. In this manuscript, the progress on the numerical studies on impact-pin nozzle are reported. A small computational domain covering the orifice, pin tip and the region where primary atomization occurs is selected for numerical analysis. The governing equations are selected in three dimensional cartesian form and simulations are performed to predict the dynamics of water jet impinging on the pin. Systematic studies were carried out and the results leading to the choice of turbulence model and the effect of pin tip diameter are reported here. Further studies are proposed to show the future directions of the present research work.

  16. Nanowall pinning for enhanced pinning force in YBCO films with nanofabricated structures

    Energy Technology Data Exchange (ETDEWEB)

    Palau, A.; Rouco, V.; Luccas, R.F.; Obradors, X.; Puig, T., E-mail: teresa.puig@icmab.es

    2014-11-15

    Highlights: • High resolution lithography techniques to fabricate artificial pinning centres in high temperature superconductors. • Enhanced critical currents of YBCO films with engineered nanofabricated structures. • Controlled nano-walls with weakened superconductivity acting as strong pinning centres. - Abstract: High resolution nanofabrication tools (Focused Ion Beam and Electron Beam Lithography) have been used to fabricate nano-metric milled structures in high critical current YBCO thin films able to further increase their vortex pinning capabilities. We have demonstrated that pinning forces at 77 K and 3 T are increased by a 70–80% by proper nanostructure designs. Model systems with linear trenches and triangular blind antidots of different sizes, distribution and density have been generated and studied. We demonstrate that specific milled nanostructures can increase the total current through the system at expenses of a limited decrease of cross section. We have identified the length of fabricated nano-walls as the main parameter controlling the pinning potential of nanostructures and thus defined the optimised milling conditions and nanostructure morphology to maximise pinning efficiency.

  17. Melt Rate Improvement for DWPF MB3: Foaming Theory and Mitigation Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Peeler, D.K.

    2001-07-24

    The objective of this research is to enhance the basic understanding of the role of glass chemistry, including the chemical kinetics of pre-melting, solid state reactions, batch melting, and the reaction pathways in glass and/or acid addition strategy changes on the overall melting process for the Defense Waste Processing Facility (DWPF) Macrobatch 3 (MB3).

  18. Differential Roles of PIN1 and PIN2 in Root Meristem Maintenance Under Low-B Conditions in Arabidopsis thaliana.

    Science.gov (United States)

    Li, Ke; Kamiya, Takehiro; Fujiwara, Toru

    2015-06-01

    Boron (B) is an essential element for plants; its deficiency causes rapid cessation of root elongation. In addition, B influences auxin accumulation in plants. To assess the importance of auxin transport in B-dependent root elongation, Arabidopsis thaliana pin1-pin4 mutants were grown under low-B conditions. Among them, only the pin2/eir1-1 mutant showed a significantly shorter root under low-B conditions than under control conditions. Moreover, the root meristem size of pin2/eir1-1 was reduced under low-B conditions. Among the PIN-FORMED (PIN) family, PIN1 and PIN2 are important for root meristem growth/maintenance under normal conditions. To investigate the differential response of pin1 and pin2 mutants under low-B conditions, the effect of low-B on PIN1-green fluorescent protein (GFP) and PIN2-GFP accumulation and localization was examined. Low-B did not affect PIN2-GFP, while it reduced the accumulation of PIN1-GFP. Moreover, no signal from DII-VENUS, an auxin sensor, was detected under the low-B condition in the stele of wild-type root meristems. Taken together, these results indicate that under low-B conditions PIN1 is down-regulated and PIN2 plays an important role in root meristem maintenance. © The Author 2015. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  19. Genome-wide identification and evolution of the PIN-FORMED (PIN) gene family in Glycine max.

    Science.gov (United States)

    Liu, Yuan; Wei, Haichao

    2017-07-01

    Soybean (Glycine max) is one of the most important crop plants. Wild and cultivated soybean varieties have significant differences worth further investigation, such as plant morphology, seed size, and seed coat development; these characters may be related to auxin biology. The PIN gene family encodes essential transport proteins in cell-to-cell auxin transport, but little research on soybean PIN genes (GmPIN genes) has been done, especially with respect to the evolution and differences between wild and cultivated soybean. In this study, we retrieved 23 GmPIN genes from the latest updated G. max genome database; six GmPIN protein sequences were changed compared with the previous database. Based on the Plant Genome Duplication Database, 18 GmPIN genes have been involved in segment duplication. Three pairs of GmPIN genes arose after the second soybean genome duplication, and six occurred after the first genome duplication. The duplicated GmPIN genes retained similar expression patterns. All the duplicated GmPIN genes experienced purifying selection (Ka/Ks < 1) to prevent accumulation of non-synonymous mutations and thus remained more similar. In addition, we also focused on the artificial selection of the soybean PIN genes. Five artificially selected GmPIN genes were identified by comparing the genome sequence of 17 wild and 14 cultivated soybean varieties. Our research provides useful and comprehensive basic information for understanding GmPIN genes.

  20. Pinning Synchronization of One-Sided Lipschitz Complex Networks

    Directory of Open Access Journals (Sweden)

    Fang Liu

    2014-01-01

    Full Text Available This paper studies the pinning synchronization in complex networks with node dynamics satisfying the one-sided Lipschitz condition which is less conservative than the well-known Lipschitz condition. Based on M-matrix theory and Lyapunov functional method, some simple pinning conditions are derived for one-sided Lipschitz complex networks with full-state and partial-state coupling, respectively. A selective pinning scheme is further provided to address the selection of pinned nodes and the design of pinning feedback gains for one-sided Lipschitz complex networks with general topologies. Numerical results are given to illustrate the effectiveness of the theoretical analysis.

  1. The pin pixel detector--neutron imaging

    CERN Document Server

    Bateman, J E; Derbyshire, G E; Duxbury, D M; Marsh, A S; Rhodes, N J; Schooneveld, E M; Simmons, J E; Stephenson, R

    2002-01-01

    The development and testing of a neutron gas pixel detector intended for application in neutron diffraction studies is reported. Using standard electrical connector pins as point anodes, the detector is based on a commercial 100 pin connector block. A prototype detector of aperture 25.4 mmx25.4 mm has been fabricated, giving a pixel size of 2.54 mm which matches well to the spatial resolution typically required in a neutron diffractometer. A 2-Dimensional resistive divide readout system has been adapted to permit the imaging properties of the detector to be explored in advance of true pixel readout electronics. The timing properties of the device match well to the requirements of the ISIS-pulsed neutron source.

  2. Cheap and Easy PIN Entering Using Eye Gaze

    Directory of Open Access Journals (Sweden)

    Kasprowski Pawel

    2014-03-01

    Full Text Available PINs are one of the most popular methods to perform simple and fast user authentication. PIN stands for Personal Identification Number, which may have any number of digits or even letters. Nevertheless, 4-digit PIN is the most common and is used for instance in ATMs or cellular phones. The main advantage of the PIN is that it is easy to remember and fast to enter. There are, however, some drawbacks. One of them - addressed in this paper - is a possibility to steal PIN by a technique called `shoulder surfing'. To avoid such problems a novel method of the PIN entering was proposed. Instead of using a numerical keyboard, the PIN may be entered by eye gazes, which is a hands-free, easy and robust technique. References:

  3. Timing analysis of PWR fuel pin failures

    Energy Technology Data Exchange (ETDEWEB)

    Jones, K.R.; Wade, N.L.; Katsma, K.R.; Siefken, L.J. (EG and G Idaho, Inc., Idaho Falls, ID (United States)); Straka, M. (Halliburton NUS, Idaho Falls, ID (United States))

    1992-09-01

    Research has been conducted to develop and demonstrate a methodology for calculation of the time interval between receipt of the containment isolation signals and the first fuel pin failure for loss-of-coolant accidents (LOCAs). Demonstration calculations were performed for a Babcock and Wilcox (B W) design (Oconee) and a Westinghouse (W) four-loop design (Seabrook). Sensitivity studies were performed to assess the impacts of fuel pin bumup, axial peaking factor, break size, emergency core cooling system availability, and main coolant pump trip on these times. The analysis was performed using the following codes: FRAPCON-2, for the calculation of steady-state fuel behavior; SCDAP/RELAP5/MOD3 and TRACPF1/MOD1, for the calculation of the transient thermal-hydraulic conditions in the reactor system; and FRAP-T6, for the calculation of transient fuel behavior. In addition to the calculation of fuel pin failure timing, this analysis provides a comparison of the predicted results of SCDAP/RELAP5/MOD3 and TRAC-PFL/MOD1 for large-break LOCA analysis. Using SCDAP/RELAP5/MOD3 thermal-hydraulic data, the shortest time intervals calculated between initiation of containment isolation and fuel pin failure are 10.4 seconds and 19.1 seconds for the B W and W plants, respectively. Using data generated by TRAC-PF1/MOD1, the shortest intervals are 10.3 seconds and 29.1 seconds for the B W and W plants, respectively. These intervals are for a double-ended, offset-shear, cold leg break, using the technical specification maximum peaking factor and applied to fuel with maximum design bumup. Using peaking factors commensurate widi actual bumups would result in longer intervals for both reactor designs. This document also contains appendices A through J of this report.

  4. Mesoscopic pinning forces in neutron star crusts

    CERN Document Server

    Seveso, Stefano; Grill, Fabrizio; Haskell, Brynmor

    2014-01-01

    The crust of a neutron star is thought to be comprised of a lattice of nuclei immersed in a sea of free electrons and neutrons. As the neutrons are superfluid their angular momentum is carried by an array of quantized vortices. These vortices can pin to the nuclear lattice and prevent the neutron superfluid from spinning down, allowing it to store angular momentum which can then be released catastrophically, giving rise to a pulsar glitch. A crucial ingredient for this model is the maximum pinning force that the lattice can exert on the vortices, as this allows us to estimate the angular momentum that can be exchanged during a glitch. In this paper we perform, for the first time, a detailed and quantitative calculation of the pinning force \\emph{per unit length} acting on a vortex immersed in the crust and resulting from the mesoscopic vortex-lattice interaction. We consider realistic vortex tensions, allow for displacement of the nuclei and average over all possible orientation of the crystal with respect to...

  5. Signatures of nonthermal melting

    Directory of Open Access Journals (Sweden)

    Tobias Zier

    2015-09-01

    Full Text Available Intense ultrashort laser pulses can melt crystals in less than a picosecond but, in spite of over thirty years of active research, for many materials it is not known to what extent thermal and nonthermal microscopic processes cause this ultrafast phenomenon. Here, we perform ab-initio molecular-dynamics simulations of silicon on a laser-excited potential-energy surface, exclusively revealing nonthermal signatures of laser-induced melting. From our simulated atomic trajectories, we compute the decay of five structure factors and the time-dependent structure function. We demonstrate how these quantities provide criteria to distinguish predominantly nonthermal from thermal melting.

  6. Improved Pinning Center Morphology in HTS with Order-of-Magnitude Increase in Jc and Bpin Compared to Columnar Pinning

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The motivation for continuouscolumnar pinning centers has been to provide maximum Upin. It has been assumed that this provides the best Jc and Bpin. Limitations on Jc and Bpin observed for columnar pinning have been attributed to degradation of the order parameter and Tc. We examine columnar pinning by ionic damage and conclude instead that geometrical effects of columnar pinningon percolation path and on the number of pinning centers are the dominant limitations of columnar pinning, leading to a limit of Bpin~4 T. Evidence suggests that multiple-in-line-defects (MILD) are far better suited to increase Jc and Bpin. The morphology of MILD pinning is reviewed. Ion energy loss per unit distance, Se, is found to be most promising in a regime almost diametrically opposite to that sought to maximize Upin. We expect Jc~106 A/cm2 and Bpin>40 T from MILD pinning,despite sharply decreased Upin.Experimental confirmation is proposed.

  7. Melt Cast High Explosives

    Directory of Open Access Journals (Sweden)

    Stanisław Cudziło

    2014-12-01

    Full Text Available [b]Abstract[/b]. This paper reviews the current state and future developments of melt-cast high explosives. First the compositions, properties and methods of preparation of trinitrotoluene based (TNT conventional mixtures with aluminum, hexogen (RDX or octogen (HMX are described. In the newer, less sensitive explosive formulations, TNT is replaced with dinitroanisole (DNANDNANDNAN and nitrotriazolone (NTONTONTO, nitroguanidine (NG or ammonium perchlorate (AP are the replacement for RDRDX and HMX. Plasticized wax or polymer-based binder systems for melt castable explosives are also included. Hydroxyl terminated polybutadiene (HPTB is the binder of choice, but polyethylene glycol, and polycaprolactone with energetic plasticizers are also used. The most advanced melt-cast explosives are compositions containing energetic thermoplastic elastomers and novel highly energetic compounds (including nitrogen rich molecules in whose particles are nanosized and practically defect-less.[b]Keywords[/b]: melt-cast explosives, detonation parameters

  8. Melting of sodium clusters

    CERN Document Server

    Reyes-Nava, J A; Beltran, M R; Michaelian, K

    2002-01-01

    Thermal stability properties and the melting-like transition of Na_n, n=13-147, clusters are studied through microcanonical molecular dynamics simulations. The metallic bonding in the sodium clusters is mimicked by a many-body Gupta potential based on the second moment approximation of a tight-binding Hamiltonian. The characteristics of the solid-to-liquid transition in the sodium clusters are analyzed by calculating physical quantities like caloric curves, heat capacities, and root-mean-square bond length fluctuations using simulation times of several nanoseconds. Distinct melting mechanisms are obtained for the sodium clusters in the size range investigated. The calculated melting temperatures show an irregular variation with the cluster size, in qualitative agreement with recent experimental results. However, the calculated melting point for the Na_55 cluster is about 40 % lower than the experimental value.

  9. Magnetic flux pinning in superconductors with hyperbolic-tessellation arrays of pinning sites

    Science.gov (United States)

    Misko, V. R.; Nori, Franco

    2012-05-01

    We study magnetic flux interacting with arrays of pinning sites (APSs) placed on vertices of hyperbolic tessellations (HTs). We show that, due to the gradient in the density of pinning sites, HT APSs are capable of trapping vortices for a broad range of applied magnetic fluxes. Thus, the penetration of magnetic field in HT APSs is essentially different from the usual scenario predicted by the Bean model. We demonstrate that, due to the enhanced asymmetry of the surface barrier for vortex entry and exit, this HT APS could be used as a “capacitor” to store magnetic flux.

  10. Force induced DNA melting

    Energy Technology Data Exchange (ETDEWEB)

    Santosh, Mogurampelly; Maiti, Prabal K [Center for Condensed Matter Theory, Department of Physics, Indian Institute of Science, Bangalore-12 (India)], E-mail: santosh@physics.iisc.ernet.in, E-mail: maiti@physics.iisc.ernet.in

    2009-01-21

    When pulled along the axis, double-strand DNA undergoes a large conformational change and elongates by roughly twice its initial contour length at a pulling force of about 70 pN. The transition to this highly overstretched form of DNA is very cooperative. Applying a force perpendicular to the DNA axis (unzipping), double-strand DNA can also be separated into two single-stranded DNA, this being a fundamental process in DNA replication. We study the DNA overstretching and unzipping transition using fully atomistic molecular dynamics (MD) simulations and argue that the conformational changes of double-strand DNA associated with either of the above mentioned processes can be viewed as force induced DNA melting. As the force at one end of the DNA is increased the DNA starts melting abruptly/smoothly above a critical force depending on the pulling direction. The critical force f{sub m}, at which DNA melts completely decreases as the temperature of the system is increased. The melting force in the case of unzipping is smaller compared to the melting force when the DNA is pulled along the helical axis. In the case of melting through unzipping, the double-strand separation has jumps which correspond to the different energy minima arising due to sequence of different base pairs. The fraction of Watson-Crick base pair hydrogen bond breaking as a function of force does not show smooth and continuous behavior and consists of plateaus followed by sharp jumps.

  11. ELM induced tungsten melting and its impact on tokamak operation

    Science.gov (United States)

    Coenen, J. W.; Arnoux, G.; Bazylev, B.; Matthews, G. F.; Jachmich, S.; Balboa, I.; Clever, M.; Dejarnac, R.; Coffey, I.; Corre, Y.; Devaux, S.; Frassinetti, L.; Gauthier, E.; Horacek, J.; Knaup, M.; Komm, M.; Krieger, K.; Marsen, S.; Meigs, A.; Mertens, Ph.; Pitts, R. A.; Puetterich, T.; Rack, M.; Stamp, M.; Sergienko, G.; Tamain, P.; Thompson, V.

    2015-08-01

    In JET-ILW dedicated melt exposures were performed using a sequence of 3MA/2.9T H-Mode JET pulses with an input power of PIN = 23 MW, a stored energy of ∼6 MJ and regular type I ELMs at ΔWELM = 0.3 MJ and fELM ∼ 30 Hz. In order to assess the risk of starting ITER operations with a full W divertor, one of the task was to measure the consequences of W transients melting due to ELMs. JET is the only tokamak able to produce transients/ ELMs large enough (>300 kJ per ELM) to facilitate melting of tungsten. Such ELMs are comparable to mitigated ELMs expected in ITER. By moving the outer strike point (OSP) onto a dedicated leading edge the base temperature was raised within ∼1 s to allow transient ELM-driven melting during the subsequent 0.5 s. Almost 1 mm (∼6 mm3) of W was moved by ∼ 150 ELMs within 5 subsequent discharges. Significant material losses in terms of ejections into the plasma were not observed. There is indirect evidence that some small droplets (∼ 80 μm) were ejected. The impact on the main plasma parameters is minor and no disruptions occurred. The W-melt gradually moved along the lamella edge towards the high field side, driven by j × B forces. The evaporation rate determined is 100 times less than expected from steady state melting and thus only consistent with transient melting during individual ELMs. IR data, spectroscopy, as well as melt modeling point to transient melting. Although the type of damage studied in these JET experiments is unlikely to be experienced in ITER, the results do strongly support the design strategy to avoid exposed edges in the ITER divertor. The JET experiments required a surface at normal incidence and considerable pre-heating to produce tungsten melting. They provide unique experimental evidence for the absence of significant melt splashing at events resembling mitigated ELMs on ITER and establish a unique experimental benchmark for the simulations being used to study transient shallow melting on ITER W

  12. Robustness of pinning a general complex dynamical network

    Energy Technology Data Exchange (ETDEWEB)

    Wang Lei, E-mail: lwang@buaa.edu.c [Laboratory of Mathematics, Information and Behavior of the Ministry of Education, Department of Systems and Control, Beihang University, Beijing 100191 (China); Sun Youxian [State Key Laboratory of Industrial Control Technology, Institute of Industrial Process Control, Zhejiang University, Hangzhou 310027 (China)

    2010-04-05

    This Letter studies the robustness problem of pinning a general complex dynamical network toward an assigned synchronous evolution. Several synchronization criteria are presented to guarantee the convergence of the pinning process locally and globally by construction of Lyapunov functions. In particular, if a pinning strategy has been designed for synchronization of a given complex dynamical network, then no matter what uncertainties occur among the pinned nodes, synchronization can still be guaranteed through the pinning. The analytical results show that pinning control has a certain robustness against perturbations on network architecture: adding, deleting and changing the weights of edges. Numerical simulations illustrated by scale-free complex networks verify the theoretical results above-acquired.

  13. A mechanism to pin skyrmions in chiral magnets.

    Science.gov (United States)

    Liu, Ye-Hua; Li, You-Quan

    2013-02-20

    We propose a mechanism to pin skyrmions in chiral magnetic thin films by introducing local maxima of magnetic exchange strength as pinning centers. The local maxima can be realized by engineering the local density of itinerant electrons. The stationary properties and the dynamical pinning and depinning processes of an isolated skyrmion around a pinning center are studied. We carry out numerical simulations of the Landau-Lifshitz-Gilbert (LLG) equation and find a way to control the position of an isolated skyrmion in a pinning center lattice using electric current pulses. The results are verified by a Thiele equation analysis. We also find that the critical current to depin a skyrmion, which is estimated to have order of magnitude 10(7)-10(8) A m(-2), has linear dependence on the pinning strength.

  14. Principles of intramedullary pin and wire fixation.

    Science.gov (United States)

    Howard, P E

    1991-02-01

    Knowledge and experience in the proper use of IM pins, K-wires, and orthopedic wire is a valuable asset to the veterinarian's ability to successfully repair a variety of long bone fractures. Most long bone fractures are amenable to repair with this form of fixation. When the principles of application are violated or the implants are used when contraindicated, complications often occur. Proper use of these implants results in the successful management of complex fractures to the satisfaction of both the animal owner and the veterinarian (Fig 10).

  15. Controlling Flow Turbulence Using Local Pinning Feedback

    Institute of Scientific and Technical Information of China (English)

    TANG Guo-Ning; HU Gang

    2006-01-01

    Flow turbulence control in two-dimensional Navier-Stokes equation is considered.By applying local pinning control only to a sjngle component of flow velocity field,the flow turbulence can be controlled to desirable targets.It is found that with certain number of controllers there exist an optimal control strength at which control error takes minimum value,and larger and smaller control strengths give worse control efficiency.The phvsical mechanism underlying these strange control results is analysed based on the interactions between different types of modes.

  16. Optimum Prestress of Tanks with Pinned Base

    DEFF Research Database (Denmark)

    Brøndum-Nielsen, Troels

    1998-01-01

    Amin Ghali and Eleanor Elliott presented in their paper an interesting suggestion for prestressing of circular tanks without sliding joints. For many prestressed tanks the following construction procedure is adopted:In order to ensure compressive hoop forces in the wall near the base, the wall...... is allowed to slide freely in the radial direction during tensioning (free base).After tensioning such displacements are prevented (pinned base). The present paper addresses the problem of prestress of such tanks.Keywords: circular prestressing; creep properties; prestressed concrete; redistribution...... of stress; stress relaxation; tanks....

  17. MELTED BUTTER TECHNOLOGY DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    L. V. Golubeva

    2014-01-01

    Full Text Available Summary. Melted butter is made from dairy butter by rendering the fat phase. It has specific taste and aroma, high-calorie content and good assimilability. Defects of butter which appeared during the storage causes by the development of microbiological processes or by the chemical oxidation. On the development of these processes influence quality and composition of fresh butter, its physical structure, content of the increased amount of gas phase and content of heavy metals, storage conditions. Microbiological spoilage of butter occurs generally due to damage of plasma which is good environment for the development of microorganisms. Defects of microbiological origin include: unclean, sour, moldy, yeasty, cheesy, bitter taste. Defects of test and smell chemical origin are formed due to hydrolytic digestion of lipids. It's prevailed at long storage of butter in the conditions of freezing temperatures. It's picked out the following main processes of spoiling: souring, acidifying and sallowness. Often these processes take place simultaneously.It has been investigated melted butter with lactated additive. The latter improves the microbiological and toxicological safety, prolongs the storage condition of the products. Technological efficiency of the additives is achieved by a multilayer products formation from the inactive bound water, preventing microorganisms growth and by the barrier layer with lactate inhibiting hydrolytic reactions. Oil samples were obtained with the batch-type butter maker application, then they were melted and after that lactated additive were supplemented. It has been studied organoleptic and physico-chemical indices of the melted butter samples. The fatty-acid composition of melted butter were studied. Comparative analysis of fatty-acid composition of cow's milk fat and produced melted butter has shown their similarity. Also in the last sample there is increased weight fraction of linoleic and linolenic acids. The obtained

  18. Development of 3D pseudo pin-by-pin calculation methodology in ANC

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, B.; Mayhue, L.; Huria, H.; Ivanov, B. [Westinghouse Electric Company LLC, 1000 Westinghouse Drive, Cranberry, PA 16066 (United States)

    2012-07-01

    Advanced cores and fuel assembly designs have been developed to improve operational flexibility, economic performance and further enhance safety features of nuclear power plants. The simulation of these new designs, along with strong heterogeneous fuel loading, have brought new challenges to the reactor physics methodologies currently employed in the industrial codes for core analyses. Control rod insertion during normal operation is one operational feature in the AP1000{sup R} plant of Westinghouse next generation Pressurized Water Reactor (PWR) design. This design improves its operational flexibility and efficiency but significantly challenges the conventional reactor physics methods, especially in pin power calculations. The mixture loading of fuel assemblies with significant neutron spectrums causes a strong interaction between different fuel assembly types that is not fully captured with the current core design codes. To overcome the weaknesses of the conventional methods, Westinghouse has developed a state-of-the-art 3D Pin-by-Pin Calculation Methodology (P3C) and successfully implemented in the Westinghouse core design code ANC. The new methodology has been qualified and licensed for pin power prediction. The 3D P3C methodology along with its application and validation will be discussed in the paper. (authors)

  19. The pin pixel detector--X-ray imaging

    CERN Document Server

    Bateman, J E; Derbyshire, G E; Duxbury, D M; Marsh, A S; Simmons, J E; Stephenson, R

    2002-01-01

    The development and testing of a soft X-ray gas pixel detector, which uses connector pins for the anodes is reported. Based on a commercial 100 pin connector block, a prototype detector of aperture 25.4 mm centre dot 25.4 mm can be economically fabricated. The individual pin anodes all show the expected characteristics of small gas detectors capable of counting rates reaching 1 MHz per pin. A 2-dimensional resistive divide readout system has been developed to permit the imaging properties of the detector to be explored in advance of true pixel readout electronics.

  20. [Ingestion of an open safety pin--challenging treatment].

    Science.gov (United States)

    DeRowe, Ari; Fishman, Gadi; Avni, Hadas; Reider, Ivgeny; Ogorek, Daniel

    2003-11-01

    A 9 month old girl at the emergency room appeared with an acute onset of restlessness, drooling and suspected foreign body ingestion. An X-Ray revealed an open safety pin in the child's upper aero-digestive tract. The source of the safety pin was a "Hamsah" good luck charm that was attached to her bed. Open safety pins in the aero-digestive tract are difficult to manage and great care must be taken during removal to prevent further injury. Parents should be counseled regarding the presence of safety pins in the child's surroundings in order to prevent such hazards.

  1. Changing the flux flow state in weak pinning superconducting films

    Energy Technology Data Exchange (ETDEWEB)

    Leo, A., E-mail: antoleo@sa.infn.it [Physics Department E.R. Caianiello, University of Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy); CNR-SPIN Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy); Grimaldi, G. [CNR-SPIN Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy); Nigro, A. [Physics Department E.R. Caianiello, University of Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy); CNR-SPIN Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy); Bruno, E.; Priolo, F. [Matis IMM-CNR and Physics-Astronomy Department, Catania University, CT 95123 (Italy); Pace, S. [Physics Department E.R. Caianiello, University of Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy); CNR-SPIN Salerno, Via Giovanni Paolo II, 132, Stecca 9, I-84084 Fisciano, SA (Italy)

    2014-08-15

    Highlights: • We analyzed the effect of light ion irradiation on weak pinning superconductors. • We found the light ion irradiation has a strong impact on current currying stability. • We compared the results to the ones of the case of moderate strong pinning materials. - Abstract: The current carrying dissipative state well above the critical current it is known to be related to the pinning properties of the material and to the microscopic mechanisms of vortex dynamics. Moreover, it has been demonstrated that in low temperature superconducting films exhibiting moderately strong pinning the light ion irradiation has the effect of changing the distribution of the pinning centers without changing their pinning strength and this results into an increase of current stability in the flux flow state. Here we present the results of light ion irradiation on weak pinning superconducting films focusing on the influence of pinning properties of the material in the flux flow state. We realize that the possibility to switch to low dissipations by changing weak pinning is not straightforward.

  2. Pin-ups: pictures that fascinate and seduce Pin-ups: fotografias que encantam e seduzem

    Directory of Open Access Journals (Sweden)

    Maria Irene Pellegrino de Oliveira Souza

    2010-08-01

    Full Text Available Starting from photography studies, social anthropology and body visual, this article approaches the social construction of the feminine image through times. It narrates the history of erotic pinups photography and its fetishist elements. Pin-ups have aroused in the end of 19tcentury and it represents the free spirit of women. Slowly, it provokes the breakup of sensuality and sexuality feminine traditionalism. The article also discusses women’s sensuality as a desire object. The pin-ups sensual demure – with a mystery atmosphere – stimulated the eroticism at the beginning of the 20 century and, until nowadays, it provokes admiration, sigh and desire. Com base em estudos sobre fotografia, antropologia social e visual do corpo, este artigo aborda a imagem feminina socialmente construída através dos tempos. Narra o histórico da fotografia erótica de pin-ups e seus elementos fetichistas. As pin-ups surgiram no final do século XIX e representaram o espírito “livre” das mulheres. Sutilmente, incitavam o rompimento do tradicionalismo da época quanto à sensualidade e sexualidade feminina. O artigo aborda também a sensualidade feminina como objeto de desejo. O recato sensual das pin-ups – com ar de mistério – alavancou o erotismo no início do século XX e, até os dias atuais, provoca admiração, suspiros e desejos.

  3. Lightning Pin Injection Testing on MOSFETS

    Science.gov (United States)

    Ely, Jay J.; Nguyen, Truong X.; Szatkowski, George N.; Koppen, Sandra V.; Mielnik, John J.; Vaughan, Roger K.; Wysocki, Philip F.; Celaya, Jose R.; Saha, Sankalita

    2009-01-01

    Lightning transients were pin-injected into metal-oxide-semiconductor field-effect transistors (MOSFETs) to induce fault modes. This report documents the test process and results, and provides a basis for subsequent lightning tests. MOSFETs may be present in DC-DC power supplies and electromechanical actuator circuits that may be used on board aircraft. Results show that unprotected MOSFET Gates are susceptible to failure, even when installed in systems in well-shielded and partial-shielded locations. MOSFET Drains and Sources are significantly less susceptible. Device impedance decreased (current increased) after every failure. Such a failure mode may lead to cascading failures, as the damaged MOSFET may allow excessive current to flow through other circuitry. Preliminary assessments on a MOSFET subjected to 20-stroke pin-injection testing demonstrate that Breakdown Voltage, Leakage Current and Threshold Voltage characteristics show damage, while the device continues to meet manufacturer performance specifications. The purpose of this research is to develop validated tools, technologies, and techniques for automated detection, diagnosis and prognosis that enable mitigation of adverse events during flight, such as from lightning transients; and to understand the interplay between lightning-induced surges and aging (i.e. humidity, vibration thermal stress, etc.) on component degradation.

  4. Optimizing Dynamical Network Structure for Pinning Control

    Science.gov (United States)

    Orouskhani, Yasin; Jalili, Mahdi; Yu, Xinghuo

    2016-04-01

    Controlling dynamics of a network from any initial state to a final desired state has many applications in different disciplines from engineering to biology and social sciences. In this work, we optimize the network structure for pinning control. The problem is formulated as four optimization tasks: i) optimizing the locations of driver nodes, ii) optimizing the feedback gains, iii) optimizing simultaneously the locations of driver nodes and feedback gains, and iv) optimizing the connection weights. A newly developed population-based optimization technique (cat swarm optimization) is used as the optimization method. In order to verify the methods, we use both real-world networks, and model scale-free and small-world networks. Extensive simulation results show that the optimal placement of driver nodes significantly outperforms heuristic methods including placing drivers based on various centrality measures (degree, betweenness, closeness and clustering coefficient). The pinning controllability is further improved by optimizing the feedback gains. We also show that one can significantly improve the controllability by optimizing the connection weights.

  5. Medio-lateral entry pin versus lateral entry pin for displaced pediatric supracondylar fractures: A comparative, prospective study

    Directory of Open Access Journals (Sweden)

    Manoj Kandel

    2016-01-01

    Full Text Available Background & Objectives: Supracondylar fracture is one of the commonest fractures in children. Although the technique of pinning is controversial, percutaneous medio-lateral entry pinning is theoretically considered more stable biomechanical construct. The drawback of this method is injury to ulnar nerve which is not encountered in only lateral entry pinning.Materials & Methods: This was a prospective, comparative and observational study done in 60 patients which was alternately divided into two groups. The first group (A underwent medio-lateral entry pinning and the second group (B underwent lateral entry pinning. They were followed for 24 weeks and the outcome was assessed using Flynn’s criteria.Results: At twenty-four weeks, the mean loss of range of motion of elbow in medio-lateral pinning group was 3.70 degrees (SD±1.93 and that in lateral pinning group was 4.23 degrees (SD ±1.38. The mean loss in carrying angle at twenty-four weeks in medio-lateral group was 2.93 degrees (SD±2.19 and that in lateral group was 4.17 (SD±2.24. There were 2 (6.67% cases of iatrogenic ulnar nerve injury in medio-lateral pinning group. Out of thirty patients, in medio-lateral pinning group, 25 had excellent results, 5 had good results and none had fair or poor results. While out of 30 patients in lateral pinning group, 23 had excellent results, 7 had good results and none had fair or poor results.Conclusion: There is no significant difference in outcome in terms of loss of carrying angle and range of motion between the medio-lateral pinning group and the lateral pinning group at the end of 6 months.Journal of College of Medical Sciences-Nepal, Vol.11(4 2015: 28-31

  6. Application of direct laser melting to restore damaged steel dies

    Science.gov (United States)

    Jang, Jeong Hwan; Joo, Byeong Don; Mun, Sung Min; Sung, Min Young; Moon, Young Hoon

    2011-02-01

    Direct laser melting (DLM) technology can be applied to restore damaged steel dies. To understand the effects of DLM process parameters such as the laser power and scan rate, a series of experiments was conducted to determine the optimal operating parameters. To investigate the laser melting characteristics, the depth/height ratio, depth/width ratio and micro-hardness as a function of the laser energy density were analyzed. Fe-Cr and Fe-Ni layers were deposited on a steel die with 11.38 J/mm2 of energy input. The wear-resistance and the friction coefficient of the deposited layer were investigated by a pin-on-disk test. The penetration depth decreased as the scan rate increased as a consequence of the shorter interaction time. The depth/height ratio of the deposited layer decreased with an increase in the scan rate. The depth/width ratio increased as laser power increased and the scan rate decreased. The deposition shape of the Fe-Ni powder was relatively shallow and wide compared with that of the Fe-Cr powder. The scan rate had a substantial effect upon the deposition height, with the Fe-Cr powder melting more than the Fe-Ni powder. The micro-hardness of the layer melted from the powders is higher than that of the substrate, and the hardness of the laser-surface-melted layer without any metal powder is higher compared to that of the metal-powder-melted layer. The direct laser melting process with Fe-Ni powder represents a superior method when restoring a steel die when the bead shape and hardness of the restored surface are important outcome considerations.

  7. Nanoengineering of Flux Pinning Sites in High-Tc Superconductors

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Volume pinning forces were determined for a variety of bulk high-Tcsuperconductors of the 123-type from magnetization measurements. By means of scaling of the pinning forces, the acting pinning mechanisms in various temperature ranges were identified. The Nd-based superconductors and some YBCO crystalsexhibited a dominating pinning of the δTc-type (i.e., small, superconducting pinning sites). In contrast to this, the addition of insulating 211 particles provided pinning of the δl-type; providing effective pinning in the entire temperature range acting as a "background" pinning mechanism for the peak effect. Due to the small coherence lengths of the high-Tc compounds, effective pinning sites are defects or particles of nanometer size relative to ξ3. Integral magnetic measurements of the magnetization as a function of temperature in large applied magnetic fields (up to 7 T) revealed that practically all high-Tc compounds were spatially inhomogeneous, which could be caused byoxygen deficiency (YBCO), solid solutions of Nd/Ba (NdBCO and other light rare earth compounds), intergrowths (Bi-based superconductors), and doping by pair-breaking dopants like Zn, Pr. This implies that the superconducting sample consists of stronger and weaker superconducting areas, coupled together. In large appliedfields, this coupling gets broken and the magnetization versus temperature curves revealed more than one superconducting transition. In contrast, irradiation experiments by neutrons, protons, and heavy-ions enabled the artificial introduction of very effective pinning sites into the high-Tc superconductors, thus creating a large variety of different observations using magnetic data. From all these observations, we construct a pinning diagram for bulk high-Tc superconductors explaining many features observed in high-Tc samples.

  8. Fundamental Characteristics of a Pinned Photodiode CMOS Pixels

    NARCIS (Netherlands)

    Xu, Y.

    2015-01-01

    This thesis gives an insightful analysis of the pinned photodiode 4T CMOS pixel from three different aspects. Firstly, from the charge accumulated aspect, the PPD full well capacity and related parameters of influence are investigated such as the pinning voltage, and transfer gate potential barrier.

  9. IMp: The customizable LEGO(®) Pinned Insect Manipulator.

    Science.gov (United States)

    Dupont, Steen; Price, Benjamin; Blagoderov, Vladimir

    2015-01-01

    We present a pinned insect manipulator (IMp) constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble.

  10. Viscosity Measurement for Tellurium Melt

    Science.gov (United States)

    Lin, Bochuan; Li, Chao; Ban, Heng; Scripa, Rosalia N.; Su, Ching-Hua; Lehoczky, Sandor L.

    2006-01-01

    The viscosity of high temperature Te melt was measured using a new technique in which a rotating magnetic field was applied to the melt sealed in a suspended ampoule, and the torque exerted by rotating melt flow on the ampoule wall was measured. Governing equations for the coupled melt flow and ampoule torsional oscillation were solved, and the viscosity was extracted from the experimental data by numerical fitting. The computational result showed good agreement with experimental data. The melt velocity transient initiated by the rotating magnetic field reached a stable condition quickly, allowing the viscosity and electrical conductivity of the melt to be determined in a short period.

  11. Thermoacoustic Streaming and Ultrasonic Processing of Low Melting Melts

    Science.gov (United States)

    Trinh, E. H.

    1997-01-01

    Ultrasonic levitation allows the processing of low melting materials both in 1 G as well as in microgravity. The free suspension of the melts also facilitates undercooling, permitting the measurements of the physical properties of the metastable liquids.

  12. Heat transfer enhancement by pin elements

    Energy Technology Data Exchange (ETDEWEB)

    Sahiti, N.; Durst, F.; Dewan, A. [LSTM-Erlangen, Institute of Fluid Mechanics, Friedrich-Alexander-Universitaet Erlangen-Nuernberg, Cauerstrasse 4, D-91058 Erlangen (Germany)

    2005-11-01

    Heat transfer enhancement is an active and important field of engineering research since increases in the effectiveness of heat exchangers through suitable heat transfer augmentation techniques can result in considerable technical advantages and savings of costs. Considerable enhancements were demonstrated in the present work by using small cylindrical pins on surfaces of heat exchangers. A partly quantitative theoretical treatment of the proposed method is presented. It uses simple relationships for the conductive and convective heat transfer to derive an equation that shows which parameters permit the achievement of heat transfer enhancements. Experiments are reported that demonstrate the effectiveness of the results of the proposed approach. It is shown that the suggested method of heat transfer enhancements is much more effective than existing methods, since it results in an increase in heat transfer area (like fins) and also an increase in the heat transfer coefficient. (author)

  13. Cracking Bank PINs by Playing Mastermind

    Science.gov (United States)

    Focardi, Riccardo; Luccio, Flaminia L.

    The bank director was pretty upset noticing Joe, the system administrator, spending his spare time playing Mastermind, an old useless game of the 70ies. He had fought the instinct of telling him how to better spend his life, just limiting to look at him in disgust long enough to be certain to be noticed. No wonder when the next day the director fell on his chair astonished while reading, on the newspaper, about a huge digital fraud on the ATMs of his bank, with millions of Euros stolen by a team of hackers all around the world. The article mentioned how the hackers had 'played with the bank computers just like playing Mastermind', being able to disclose thousands of user PINs during the one-hour lunch break. That precise moment, a second before falling senseless, he understood the subtle smile on Joe's face the day before, while training at his preferred game, Mastermind.

  14. Flux pinning characteristics and irreversibility line in high temperature superconductors

    Science.gov (United States)

    Matsushita, T.; Ihara, N.; Kiuchi, M.

    1995-01-01

    The flux pinning properties in high temperature superconductors are strongly influenced by thermally activated flux motion. The scaling relation of the pinning force density and the irreversibility line in various high temperature superconductors are numerically analyzed in terms of the flux creep model. The effect of two factors, i.e., the flux pinning strength and the dimensionality of the material, on these properties are investigated. It is speculated that the irreversibility line in Bi-2212 superconductors is one order of magnitude smaller than that in Y-123, even if the flux pinning strength in Bi-2212 is improved up to the level of Y-123. It is concluded that these two factors are equally important in determination of the flux pinning characteristics at high temperatures.

  15. Nano-engineered pinning centres in YBCO superconducting films

    Science.gov (United States)

    Crisan, A.; Dang, V. S.; Mikheenko, P.

    2017-02-01

    For practical applications of superconducting materials in applied magnetic fields, artificial pinning centres in addition to natural ones are required to oppose the Lorentz force. These pinning centres are actually various types of defects in the superconductor matrix. The pinning centres can be categorised on their dimension (volume, surface or point) and on their character (normal cores or Δκ cores). Different samples have been produced by Pulsed Laser Deposition, with various thicknesses, temperatures and nanostructured additions to the superconducting matrix. They have been characterized by SQUID Magnetic Properties Measurement System and Physical Properties Measurement System, as well as by Transmission Electron Microscopy (TEM). Correlations between pinning architecture, TEM images, and critical currents at various fields and field orientations will be shown for a large number of YBa2Cu3Ox films with various types and architectures of artificial pinning centres.

  16. New Pin Puller Based on SMA Technology for Space Applications

    Science.gov (United States)

    Nava, Nestor; Collado, Marcelo; Cabás, Ramiro

    2014-07-01

    Two different versions of the Pin Puller were designed during this activity, such as one with 100 N and other with 500 N of pull force. The design of both versions is based on spheres which support the pin at the initial position and a compression spring driving once the release takes place by means of the SMA. The mechanical design of the Pin Pullers has been conceived in order to optimize the device's weight, reduce the parts complexity, and achieve a suitable stiffness. A qualification test campaign for the Pin Puller with 500 N of pull force has been developed in order to check the success of the proposed mechanism for space applications. The main performed tests have been thermal-vacuum actuation, thermal-vacuum cycling, sine vibration, and random vibration. The Pin Puller has presented successful results of actuation during the test campaign

  17. In vitro analysis of self-shearing retentive pins.

    Science.gov (United States)

    Collard, E W; Caputo, A A; Standlee, J P; Duncanson, M G

    1981-02-01

    Combining stress, analysis, microscopic examination, mechanical testing of the shear mechanism, and retention of the Reten Pin leads to the following conclusions: 1. The suggested 0.006 inch pin-channel mismatch induces high lateral and apical stresses. Microscopically, this was seen to correlate with injury to the dentin. 2. The degree of retention was increased by using a smaller pin-channel mismatch. This correlates with smaller stresses and reduced dentinal damage. 3. The shear mechanism acts in a uniform manner, with a relatively small variation from the mean. It is suggested that for the best results the manufacturer should supply larger twist drills and pins with a somewhat deeper self-shearing groove to minimize apical involvement during shearing of the handle from the pin.

  18. Pinning Lur’e Complex Networks via Output Feedback Control

    Directory of Open Access Journals (Sweden)

    Fang Liu

    2014-01-01

    Full Text Available Without requiring the full-state information of network nodes, this paper studies the pinning synchronization in a network of Lur’e dynamical systems based on the output feedback control strategy. Some simple pinning conditions are established for both undirected and directed Lur’e networks by using M-matrix theory and S-procedure technique. With the derived stability criteria, the pinning synchronization problem of large-scale Lur’e networks can be transformed to the test of a low-dimensional linear matrix inequality. Some remarks are further given to address the selection of pinned nodes and the design of pinning feedback gains. Numerical results are provided to demonstrate the effectiveness of the theoretical analysis.

  19. Retractable Pin Tools for the Friction Stir Welding Process

    Science.gov (United States)

    1998-01-01

    Two companies have successfully commercialized a specialized welding tool developed at the Marshall Space Flight Center (MSFC). Friction stir welding uses the high rotational speed of a tool and the resulting frictional heat created from contact to crush, 'stir' together, and forge a bond between two metal alloys. It has had a major drawback, reliance on a single-piece pin tool. The pin is slowly plunged into the joint between two materials to be welded and rotated as high speed. At the end of the weld, the single-piece pin tool is retracted and leaves a 'keyhole,' something which is unacceptable when welding cylindrical objects such as drums, pipes and storage tanks. Another drawback is the requirement for different-length pin tools when welding materials of varying thickness. An engineer at the MSFC helped design an automatic retractable pin tool that uses a computer-controlled motor to automatically retract the pin into the shoulder of the tool at the end of the weld, preventing keyholes. This design allows the pin angle and length to be adjusted for changes in material thickness and results in a smooth hole closure at the end of the weld. Benefits of friction stir welding, using the MSFC retractable pin tool technology, include the following: The ability to weld a wide range of alloys, including previously unweldable and composite materials; provision of twice the fatigue resistance of fusion welds and no keyholes; minimization of material distortion; no creation of hazards such as welding fumes, radiation, high voltage, liquid metals, or arcing; automatic retraction of the pin at the end of the weld; and maintaining full penetration of the pin.

  20. A pinning puzzle: two similar, non-superconducting chemical deposits in YBCO-one pins, the other does not

    Energy Technology Data Exchange (ETDEWEB)

    Sawh, Ravi-Persad; Weinstein, Roy; Gandini, Alberto; Skorpenske, Harley; Parks, Drew, E-mail: Weinstein@uh.ed [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Department of Physics, University of Houston, Houston, TX 77204-5005 (United States); Texas Center for Superconductivity at UH, University of Houston, Houston, TX 77204-5002 (United States)

    2009-09-15

    The pinning effects of two kinds of U-rich deposits in YBCO (YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}) are compared. One is a five-element compound, (U{sub 0.6}Pt{sub 0.4})YBa{sub 2}O{sub 6}, which is a paramagnetic double perovskite which forms as profuse stable nanosize deposits, and pins very well. The other is a four-element compound, (U{sub 0.4}Y{sub 0.6})BaO{sub 3}, which is a ferromagnetic single perovskite which forms as profuse stable nanosize deposits and pins very weakly or not at all. The pinning comparison is done with nearly equal deposit sizes and number of deposits per unit volume for the two compounds. Evidence for the pinning capability, chemical makeup, x-ray diffraction signature, and magnetic properties of the two compounds is reported.

  1. Thermodynamics of Oligonucleotide Duplex Melting

    Science.gov (United States)

    Schreiber-Gosche, Sherrie; Edwards, Robert A.

    2009-01-01

    Melting temperatures of oligonucleotides are useful for a number of molecular biology applications, such as the polymerase chain reaction (PCR). Although melting temperatures are often calculated with simplistic empirical equations, application of thermodynamics provides more accurate melting temperatures and an opportunity for students to apply…

  2. Melting of polydisperse hard disks

    NARCIS (Netherlands)

    Pronk, S.; Frenkel, D.

    2004-01-01

    The melting of a polydisperse hard-disk system is investigated by Monte Carlo simulations in the semigrand canonical ensemble. This is done in the context of possible continuous melting by a dislocation-unbinding mechanism, as an extension of the two-dimensional hard-disk melting problem. We find

  3. Melting of polydisperse hard disks

    NARCIS (Netherlands)

    Pronk, S.; Frenkel, D.

    2004-01-01

    The melting of a polydisperse hard-disk system is investigated by Monte Carlo simulations in the semigrand canonical ensemble. This is done in the context of possible continuous melting by a dislocation-unbinding mechanism, as an extension of the two-dimensional hard-disk melting problem. We find th

  4. Pavement Snow Melting

    Energy Technology Data Exchange (ETDEWEB)

    Lund, John W.

    2005-01-01

    The design of pavement snow melting systems is presented based on criteria established by ASHRAE. The heating requirements depends on rate of snow fall, air temperature, relative humidity and wind velocity. Piping materials are either metal or plastic, however, due to corrosion problems, cross-linked polyethylene pipe is now generally used instead of iron. Geothermal energy is supplied to systems through the use of heat pipes, directly from circulating pipes, through a heat exchanger or by allowing water to flow directly over the pavement, by using solar thermal storage. Examples of systems in New Jersey, Wyoming, Virginia, Japan, Argentina, Switzerland and Oregon are presented. Key words: pavement snow melting, geothermal heating, heat pipes, solar storage, Wyoming, Virginia, Japan, Argentina, Klamath Falls.

  5. Facilities & Leadership

    Data.gov (United States)

    Department of Veterans Affairs — The facilities web service provides VA facility information. The VA facilities locator is a feature that is available across the enterprise, on any webpage, for the...

  6. Dissecting Pin1 and phospho-pRb regulation.

    Science.gov (United States)

    Rizzolio, Flavio; Caligiuri, Isabella; Lucchetti, Chiara; Fratamico, Robert; Tomei, Valentina; Gallo, Gaia; Agelan, Alexis; Ferrari, Giovanni; Toffoli, Giuseppe; Klein-Szanto, Andres J; Giordano, Antonio

    2013-01-01

    The activity of the Retinoblastoma protein, the master regulator of the cell cycle, is finely regulated by phosphorylation. CDKs and cyclins are major players in phosphorylation and it has been recently discovered that the prolyl isomerase Pin1 is an essential protein that orchestrates this process. In this article, we report new findings regarding the role of Pin1 in the pRb pathway. Our data suggest that PI3K, CDKs, and the Pin1 axis have a critical role in sustaining the complete phosphorylation of pRb. Furthermore, we analyze the correlation between Pin1 and pRb phosphorylation in vivo. We show that, in human malignant glioma tissue microarrays (TMA) and in Pin1 knockout (KO) mice, there is a positive correlation between Pin1 and pRb phosphorylation. Prospectively, our findings suggest that the synergism between CDKs, Pin1, and PI3K inhibitors hold great promise for targeted pharmacological treatment of cancer patients, with the possibility of reaching high effectiveness at tolerated doses.

  7. Alar Pinning in Rigid External Distraction for Midfacial Hypoplasia.

    Science.gov (United States)

    Yu, Jenny L; Woo, Albert S

    2017-09-01

    Distraction osteogenesis with a rigid external distractor is a widely accepted treatment for midfacial hypoplasia. In this study, the authors introduce the utilization of alar pinning with the external halo distractor for maxillary advancement, in place of an oral splint. A retrospective chart review was conducted of 7 patients who successfully underwent distraction osteogenesis using the alar pinning technique. Midfacial hypoplasia was secondary to Crouzon syndrome (n = 4), Apert syndrome (n = 1), Pfeiffer syndrome (n = 1), or bacterial meningitis (n = 1). Three patients were managed with monobloc osteotomies, 2 with Le Fort III osteotomies, 1 with Le Fort III osteotomy and frontoorbital advancement, and 1 with Le Fort I osteotomy alone. Patient charts were analyzed for postoperative course and complications relating to the alar pins. Two patients had minor complications specifically related to the alar pins. One patient had concern for a mild skin infection at a pin site that resolved with oral antibiotics. The other patient had loosening of an alar pin, which did not require operative management. Retrospective chart review indicated that all patients were pleased with their results from the distraction, and no patients opted for further advancement. Utilization of alar pin sites for external distraction is a feasible and reasonable option for treatment of midfacial hypoplasia involving a Le Fort osteotomy or monobloc procedure. Fixation sites within the alar crease minimize the visibility of pin site scars and eliminate the need for a custom-made oral splint, which prevents usage of the upper dentition and frequently requires consulting a dentist or orthodontist for fabrication. Alar pinning with an external halo distraction system for management of midfacial hypoplasia has minimal complications and is an alternative to using a custom-made oral splint.

  8. Biochemistry Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Biochemistry Facility provides expert services and consultation in biochemical enzyme assays and protein purification. The facility currently features 1) Liquid...

  9. "Safety pin"--a question to its safety!

    Science.gov (United States)

    Thapa Chettri, S; Bhattarai, M; Karki, S; Regmi, S; Mathur, N N

    2010-03-01

    Foreign body ingestion is not an uncommon problem in children. They can ingest various foreign objects and one of such objects is a safety pin. The ingestion of such foreign body is not widely reported in the literature. This case highlights the risk of accidental ingestion of safety pin used on child's clothing to protect him from cold that can result in lethal complications. In a poor developing country like Nepal, this case serves to address all mothers alerting them of their ignorance while using safety pin in infants. In addition, physicians are reminded to obtain a detailed inquiry of suspected foreign body ingestion in every child with the history of dysphagia.

  10. Noises of p-i-n UV photodetectors

    Science.gov (United States)

    Gasparyan, Ferdinand V.; Korman, Can E.; Melkonyan, Slavik V.

    2007-06-01

    Investigations of the static characteristics, responsivity, internal noises, and detectivity of the forward biased p-i-n photodetectors made on wide bandgap compensated semiconductors operating in double injection regime are presented. Noise related calculations are performed by utilizing "Impedance Field Method". Numerical simulations are made assessing 4H-SiC and GaN biased p-i-n photodiodes noise related characteristics. It is shown that forward biased p-i-n photodiodes have low level of thermal and generation-recombination noises and high values of sensitivity and detectivity at the room temperature.

  11. Modelling the evaporation of boron species. Part 1: Alkali-free borosilicate glass melts

    NARCIS (Netherlands)

    Limpt, J.A.C. van; Beerkens, R.G.C.; Cook, S.; O'Connor, R.; Simon, J.

    2011-01-01

    A laboratory test facility has been used to measure the boron evaporation rates from borosilicate glass melts. The impact of furnace atmosphere composition and glass melt composition on the temperature dependent boron evaporation rates has been investigated experimentally. In Part 1 of this paper th

  12. Modelling the evaporation of boron species. Part 1: Alkali-free borosilicate glass melts

    NARCIS (Netherlands)

    Limpt, J.A.C. van; Beerkens, R.G.C.; Cook, S.; O'Connor, R.; Simon, J.

    2011-01-01

    A laboratory test facility has been used to measure the boron evaporation rates from borosilicate glass melts. The impact of furnace atmosphere composition and glass melt composition on the temperature dependent boron evaporation rates has been investigated experimentally. In Part 1 of this paper th

  13. A Division in PIN-Mediated Auxin Patterning during Organ Initiation in Grasses

    Science.gov (United States)

    O'Connor, Devin L.; Runions, Adam; Sluis, Aaron; Bragg, Jennifer; Vogel, John P.

    2014-01-01

    The hormone auxin plays a crucial role in plant morphogenesis. In the shoot apical meristem, the PIN-FORMED1 (PIN1) efflux carrier concentrates auxin into local maxima in the epidermis, which position incipient leaf or floral primordia. From these maxima, PIN1 transports auxin into internal tissues along emergent paths that pattern leaf and stem vasculature. In Arabidopsis thaliana, these functions are attributed to a single PIN1 protein. Using phylogenetic and gene synteny analysis we identified an angiosperm PIN clade sister to PIN1, here termed Sister-of-PIN1 (SoPIN1), which is present in all sampled angiosperms except for Brassicaceae, including Arabidopsis. Additionally, we identified a conserved duplication of PIN1 in the grasses: PIN1a and PIN1b. In Brachypodium distachyon, SoPIN1 is highly expressed in the epidermis and is consistently polarized toward regions of high expression of the DR5 auxin-signaling reporter, which suggests that SoPIN1 functions in the localization of new primordia. In contrast, PIN1a and PIN1b are highly expressed in internal tissues, suggesting a role in vascular patterning. PIN1b is expressed in broad regions spanning the space between new primordia and previously formed vasculature, suggesting a role in connecting new organs to auxin sinks in the older tissues. Within these regions, PIN1a forms narrow canals that likely pattern future veins. Using a computer model, we reproduced the observed spatio-temporal expression and localization patterns of these proteins by assuming that SoPIN1 is polarized up the auxin gradient, and PIN1a and PIN1b are polarized to different degrees with the auxin flux. Our results suggest that examination and modeling of PIN dynamics in plants outside of Brassicaceae will offer insights into auxin-driven patterning obscured by the loss of the SoPIN1 clade in Brassicaceae. PMID:24499933

  14. A PWR Thorium Pin Cell Burnup Benchmark

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, Kevan Dean; Zhao, X.; Pilat, E. E; Hejzlar, P.

    2000-05-01

    As part of work to evaluate the potential benefits of using thorium in LWR fuel, a thorium fueled benchmark comparison was made in this study between state-of-the-art codes, MOCUP (MCNP4B + ORIGEN2), and CASMO-4 for burnup calculations. The MOCUP runs were done individually at MIT and INEEL, using the same model but with some differences in techniques and cross section libraries. Eigenvalue and isotope concentrations were compared on a PWR pin cell model up to high burnup. The eigenvalue comparison as a function of burnup is good: the maximum difference is within 2% and the average absolute difference less than 1%. The isotope concentration comparisons are better than a set of MOX fuel benchmarks and comparable to a set of uranium fuel benchmarks reported in the literature. The actinide and fission product data sources used in the MOCUP burnup calculations for a typical thorium fuel are documented. Reasons for code vs code differences are analyzed and discussed.

  15. Multi-pin chemiresistors for microchemical sensors

    Science.gov (United States)

    Ho, Clifford K.

    2007-02-20

    A multi-pin chemiresistor for use in microchemical sensors. A pair of free-standing, bare wires is supported by an electrically insulating support, and are oriented parallel to each other and spaced closely together. A free-standing film of a chemically sensitive polymer that swells when exposed to vapors of a volatile chemical is formed in-between the pair of closely-spaced wires by capillary action. Similar in construction to a thermocouple, this "chemicouple" is relatively inexpensive and easy to fabricate by dipping the pair of bare wires into a bath of well-mixed chemiresistor ink. Also, a chemiresistor "stick" is formed by dipping an electrically insulating rod with two or more linear or spiral-wrapped electrical traces into the bath of well-mixed chemiresistor ink, which deposits a uniform coating of the chemically sensitive polymer on the rod and the electrical traces. These "sticks" can be easily removed and replaced from a multi-chemiresistor plug.

  16. Thermal experiment of silicon PIN detector

    Institute of Scientific and Technical Information of China (English)

    CHEN Hong-Fei; ZOU Ji-Qing; SHI Wei-Hong; ZOU Hong; HU Ran-Sheng; TIAN Da-Yu

    2008-01-01

    The experiment of this paper is the thermal test of the leakage current of silicon PIN detector.Raising temperature may cause the detector to increase leakage current,decrease depletion and increase noise.Three samples are used in the experiment.One (called △E) is the sample of 100 tan in thickness.The other two (called E1 and E2) are stacks of five detectors of 1000 μm in thickness.All of them are 12 mm in diameter.The experiment has been done for 21 hours and with power on continuously.The samples have undergone more than 60 ℃ for about one hour.They are not degenerated when back to the room temperature.The depletion rate is temperature and bias voltage related.With the circuit of the experiment and temperature at 35 ℃,△E is still depleted while E1 and E2 are 94.9% and 99.7% depleted respectively.The noises of the samples can be derived from the values at room temperature and the thermal dependence of the leakage currents.With the addition of the noise of the pre-amplifier,the noises of E1,E2 and AE at 24 ℃ are 16.4,16.3,and 10.5 keV (FWHM) respectively while at 35 ℃ are about 33.6,33.1,and 20.6 keV (FWHM) respectively.

  17. Superconducting vortex pinning with artificial magnetic nanostructures.

    Energy Technology Data Exchange (ETDEWEB)

    Velez, M.; Martin, J. I.; Villegas, J. E.; Hoffmann, A.; Gonzalez, E. M.; Vicent, J. L.; Schuller, I. K.; Univ. de Oviedo-CINN; Unite Mixte de Physique CNRS/Thales; Univ. Paris-Sud; Univ.Complutense de Madrid; Univ. California at San Diego

    2008-11-01

    This review is dedicated to summarizing the recent research on vortex dynamics and pinning effects in superconducting films with artificial magnetic structures. The fabrication of hybrid superconducting/magnetic systems is presented together with the wide variety of properties that arise from the interaction between the superconducting vortex lattice and the artificial magnetic nanostructures. Specifically, we review the role that the most important parameters in the vortex dynamics of films with regular array of dots play. In particular, we discuss the phenomena that appear when the symmetry of a regular dot array is distorted from regularity towards complete disorder including rectangular, asymmetric, and aperiodic arrays. The interesting phenomena that appear include vortex-lattice reconfigurations, anisotropic dynamics, channeling, and guided motion as well as ratchet effects. The different regimes are summarized in a phase diagram indicating the transitions that take place as the characteristic distances of the array are modified respect to the superconducting coherence length. Future directions are sketched out indicating the vast open area of research in this field.

  18. Ideal glass transitions by random pinning

    Science.gov (United States)

    Cammarota, Chiara; Biroli, Giulio

    2012-01-01

    We study the effect of freezing the positions of a fraction c of particles from an equilibrium configuration of a supercooled liquid at a temperature T. We show that within the random first-order transition theory pinning particles leads to an ideal glass transition for a critical fraction c = cK(T) even for moderate supercooling; e.g., close to the Mode-Coupling transition temperature. First we derive the phase diagram in the T - c plane by mean field approximations. Then, by applying a real-space renormalization group method, we obtain the critical properties for |c - cK(T)| → 0, in particular the divergence of length and time scales, which are dominated by two zero-temperature fixed points. We also show that for c = cK(T) the typical distance between frozen particles is related to the static point-to-set length scale of the unconstrained liquid. We discuss what are the main differences when particles are frozen in other geometries and not from an equilibrium configuration. Finally, we explain why the glass transition induced by freezing particles provides a new and very promising avenue of research to probe the glassy state and ascertain, or disprove, the validity of the theories of the glass transition. PMID:22623524

  19. Numerical Evaluation of Flow and Heat Transfer in Plate-Pin Fin Heat Sinks with Various Pin Cross-Sections

    OpenAIRE

    Zhou, Feng; Catton, Ivan

    2011-01-01

    A numerical investigation of the thermal and hydraulic performance of twenty different plate-pin fin heat sinks with various shapes of pin cross-section (square, circular, elliptic, NACA profile and dropform) and different ratios of pin widths to plate fin spacing (0.3, 0.4, 0.5 and 0.6) was performed. Finite Volume Method based CFD software, Ansys CFX, was used as the 3-D Reynolds-averaged Navier-Stokes Solver. A k-ω based Shear-Stress-Transport model was used to predict the turbulent flow a...

  20. Pinning properties of Y211 added cold top-seeded YBCO grown on Y2O3 layer

    Science.gov (United States)

    Çakır, Bakiye; Duman, Şeyda; Aydıner, Alev

    2016-04-01

    In this study, samples having different composition were prepared with the cold top seeding-melt-growth (TSMG) process by using Nd123 seed. Y2O3 buffer layer was placed to bottom of the pellets consist of Y123: Y211 powder mixtures. Two samples were fabricated in stoichiometric ratios of 1:0 and 1:0.4 labeled as Y0 and Y40, respectively. The Tc onset values of Y0 and Y40 were found to be 93.4 and 93.6 K at 0 T, respectively. The dependence of the effective activation energy U of the flux pinning on the magnetic field and temperature of the sample were determined using the Arrhenius activation energy law from the resistivity curves. The magnetization measurements were performed using a vibrating sample magnetometer (VSM) at 30, 50 and 77 K. The critical current densities (J c) for Y0 and Y40 samples were determined to be 5.1×103 and 3.7×103 A/cm2 at 77 K in 0 T, respectively. The normalized pinning force density versus the reduced field was examined at different temperatures to determine the pinning mechanism.

  1. Magnetic properties of high-T(sub c) superconductors: Rigid levitation, flux pinning, thermal depinning, and fluctuation

    Science.gov (United States)

    Brandt, E. H.

    1990-01-01

    The levitation of high-T(sub c) superconductors is quite conspicuous: Above magnets of low symmetry a disk of these ceramics floats motionless, without vibration or rotation; it has a continuous range of stable positions and orientations as if it were stuck in sand. Some specimens may even be suspended above or below the same magnet. This fascinating stability, inherent to no other type of levitation, is caused by the pinning of magnetic flux lines by inhomogeneities inside these extreme type-2 superconductors. The talk deals with pinning of magnetic flux in these materials, with flux flow, flux creep, thermally activated depinning, and the thermal fluctuation of the vortex positions in the flux line lattice (often called flux lattice melting). Also discussed are the fluctuations of the (nearly periodic) magnetic field inside these superconductors which are caused by random pinning sites and by the finite temperature. These fluctuations broaden the van-Hove singularities observed in the density of the magnetic field by nuclear magnetic resonance and by muon spin rotation.

  2. Procedure of recovery of pin-by-pin fields of energy release in the core of VVER-type reactor for the BIPR-8 code

    Science.gov (United States)

    Gordienko, P. V.; Kotsarev, A. V.; Lizorkin, M. P.

    2014-12-01

    The procedure of recovery of pin-by-pin energy-release fields for the BIPR-8 code and the algorithm of the BIPR-8 code which is used in nodal computation of the reactor core and on which the recovery of pin-by-pin fields of energy release is based are briefly described. The description and results of the verification using the module of recovery of pin-by-pin energy-release fields and the TVS-M program are given.

  3. Pins, dowels, and other retentive devices in posterior teeth.

    Science.gov (United States)

    Jacobi, R; Shillingburg, H T

    1993-07-01

    Devices used to increase retention of restorations to severely damaged posterior teeth are described, with an emphasis on pins and dowels. Advantages and disadvantages of different techniques and measures to help prevent and correct problems are presented.

  4. Characterization of vortex pinning through the Campbell length

    Science.gov (United States)

    Willa, Roland; Geshkenbein, Vadim B.; Blatter, Gianni

    Vortex pinning is decisive in establishing dissipation-free current flow in a type-II superconductor; knowledge and optimization of the pinning landscape (pinscape) is of major importance for applications. The ac magnetic response, characterized by the Campbell penetration depth λC, provides valuable information on the pinscape, besides the critical current density jc. While microscopic derivations of jc are available both in the weak and strong pinning limits, this is not the case for the Campbell length, whose understanding has remained on a phenomenological level so far. Based on the microscopic theory of strong pinning, we have established a proper link between the Campbell length and the pinscape parameters. This new quantitative formalism captures all experimentally observed signatures, among which are the dependence of λC on the vortex state preparation and the hysteresis in λC upon thermal cycling the field-cooled state.

  5. PIN1 in breast development and cancer: a clinical perspective.

    Science.gov (United States)

    Rustighi, Alessandra; Zannini, Alessandro; Campaner, Elena; Ciani, Yari; Piazza, Silvano; Del Sal, Giannino

    2017-02-01

    Mammary gland development, various stages of mammary tumorigenesis and breast cancer progression have the peptidyl-prolyl cis/trans isomerase PIN1 at their centerpiece, in virtue of the ability of this unique enzyme to fine-tune the dynamic crosstalk between multiple molecular pathways. PIN1 exerts its action by inducing conformational and functional changes on key cellular proteins, following proline-directed phosphorylation. Through this post-phosphorylation signal transduction mechanism, PIN1 controls the extent and direction of the cellular response to a variety of inputs, in physiology and disease. This review discusses PIN1's roles in normal mammary development and cancerous progression, as well as the clinical impact of targeting this enzyme in breast cancer patients.

  6. 8 Pin RIC Socket for Hearing Aid Applications

    DEFF Research Database (Denmark)

    Islam, Aminul; Hansen, Hans Nørgaard; Davids, Søren;

    2012-01-01

    process and the other one is fully automated process. This paper presents the entire process chain for both the concepts and makes a comparative analysis based on the experimental investigation and validation. The work presented here can be a source of valuable information for industrial users......The current paper presents the development of an 8 Pin RIC (Receiver in the canal) Socket for hearing instruments within the framework of the COTECH project. There are 8 industrial demonstrators developed in COTECH based on the converged product and process design. Sonion’s 8 Pin RIC Socket is one...... of them. 8 Pin RIC Socket is a functionally versatile product which can combine many different functions and presents many advantages compared with the previous 3 Pin RIC Socket. For the demonstrator production of the new Socket, two different production concepts were chosen- one based on semi-automated...

  7. Pinning impulsive directed coupled delayed dynamical network and its applications

    Science.gov (United States)

    Lin, Chunnan; Wu, Quanjun; Xiang, Lan; Zhou, Jin

    2015-01-01

    The main objective of the present paper is to further investigate pinning synchronisation of a complex delayed dynamical network with directionally coupling by a single impulsive controller. By developing the analysis procedure of pinning impulsive stability for undirected coupled dynamical network previously, some simple yet general criteria of pinning impulsive synchronisation for such directed coupled network are derived analytically. It is shown that a single impulsive controller can always pin a given directed coupled network to a desired homogenous solution, including an equilibrium point, a periodic orbit, or a chaotic orbit. Subsequently, the theoretical results are illustrated by a directed small-world complex network which is a cellular neural network (CNN) and a directed scale-free complex network with the well-known Hodgkin-Huxley neuron oscillators. Numerical simulations are finally given to demonstrate the effectiveness of the proposed control methodology.

  8. [Py-Desmanet pinning in distal radius fractures].

    Science.gov (United States)

    Alexa, O; Popia, I

    2009-01-01

    Internal fixation by pinning is one of the most used methods of surgical treatment in fractures of the distal extremity of the radius. As in stable fractures a styloid pinning is satisfactory, in unstable fractures however we must resort to different patterns of pin insertion, in order to effectively prevent the secondary displacement of the fractured fragments. The elastic pinning described by Py and Desmanet is one of the possibilities of inserting the pins. The principle of this method is to use the bending-induced tension in the pins to counteract the postero-lateral displacing forces. The authors have treated by this technique five patients with distal radius fractures (3 women and 2 men) about 56 years of average age, all with good-quality bone, all with Colles' fracture pattern (2-4 cm above the radio-carpal articulation, no articular involvement, posterior displacement of the distal fragment). The reduction of the fractures was achieved by closed manipulation and controlled intraoperatively with the C-arm. We preferred to reduce the fractures before inserting the pins, although this is not compulsory, according to the authors of the technique. The approach was minimally-invasive, through two 1-cm long incisions. The pins, previously blunted and curved along the last centimeters, were introduced using a "T"-shaped handle. The potential complications, consisting of injuries of the many elements which cross the region, were avoided by sufficiently long incisions and identification and retraction of these elements (tendons, nervous branches) in order not to penetrate them with the pins. The aftertreatment consisted of immediate mobilization of the wrist in one patient, 21-day splinting in other two and 30-day splinting in the last two, depending on the intraoperative assessment of the stability of the fixation. The pins were removed at 45 days postoperatively in all cases. There were no complications such as loss of reduction or pin migration. In all cases

  9. An experimental study of a pin-fin heat exchanger

    OpenAIRE

    Ramthun, David L.

    2003-01-01

    Approved for public release; distribution is unlimited A detailed experimental study has been carried out on the heat transfer and pressure drop characteristics of a compact heat exchanger with pin fins. A modular wind-tunnel with a rectangular cross-section duct-flow area was constructed that would accommodate the heat exchanger test section with varying pin designs. The flow in the tunnel was achieved through a suction-type blower, and a leading entrance length section was added to achie...

  10. Anisotropic flux pinning in high T{sub c} superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Kolesnik, S. [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, PL-02668, Warszawa (Poland); Igalson, J. [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, PL-02668, Warszawa (Poland); Skoskiewicz, T. [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, PL-02668, Warszawa (Poland); Szymczak, R. [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, PL-02668, Warszawa (Poland); Baran, M. [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, PL-02668, Warszawa (Poland); Pytel, K. [Institute of Atomic Energy, Swierk (Poland); Pytel, B. [Institute of Atomic Energy, Swierk (Poland)

    1995-02-09

    In this paper we present a comparison of the results of FC magnetization measurements on several Pb-Sr-(Y,Ca)-Cu-O crystals representing various levels of flux pinning. The pinning centers in our crystals have been set up during the crystal growth process or introduced by neutron irradiation. Some possible explanations of the observed effects, including surface barrier, flux-center distribution and sample-shape effects, are discussed. ((orig.)).

  11. Investigating the interactions of yeast prions: [SWI+], [PSI+], and [PIN+].

    Science.gov (United States)

    Du, Zhiqiang; Li, Liming

    2014-06-01

    Multiple prion elements, which are transmitted as heritable protein conformations and often linked to distinct phenotypes, have been identified in the budding yeast, Saccharomyces cerevisiae. It has been shown that overproduction of a prion protein Swi1 can promote the de novo conversion of another yeast prion [PSI(+)] when Sup35 is co-overproduced. However, the mechanism underlying this Pin(+) ([PSI(+)] inducible) activity is not clear. Moreover, how the Swi1 prion ([SWI(+)]) interacts with other yeast prions is unknown. Here, we demonstrate that the Pin(+) activity associated with Swi1 overproduction is independent of Rnq1 expression or [PIN(+)] conversion. We also show that [SWI(+)] enhances the appearance of [PSI(+)] and [PIN(+)]. However, [SWI(+)] significantly compromises the Pin(+) activity of [PIN(+)] when they coexist. We further demonstrate that a single yeast cell can harbor three prions, [PSI(+)], [PIN(+)], and [SWI(+)], simultaneously. However, under this condition, [SWI(+)] is significantly destabilized. While the propensity to aggregate underlies prionogenesis, Swi1 and Rnq1 aggregates resulting from overproduction are usually nonheritable. Conversely, prion protein aggregates formed in nonoverexpressing conditions or induced by preexisting prion(s) are more prionogenic. For [PSI(+)] and [PIN(+)] de novo formation, heterologous "facilitators," such as preexisting [SWI(+)] aggregates, colocalize only with the newly formed ring-/rod-shaped Sup35 or Rnq1 aggregates, but not with the dot-shaped mature prion aggregates. Their colocalization frequency is coordinated with their prion inducibility, indicating that prion-prion interactions mainly occur at the early initiation stage. Our results provide supportive evidence for the cross-seeding model of prionogenesis and highlight a complex interaction network among prions in yeast.

  12. Open safety pin ingestion presenting as incarcerated umbilical hernia.

    Science.gov (United States)

    Mirza, Bilal; Sheikh, Afzal

    2011-09-01

    Foreign body ingestion is common in children. Sharp foreign bodies are potentially harmful and can result various complications. An 8-month-old infant presented with incarcerated umbilical hernia. With a suspicion of strangulation, operation was performed that revealed a loop of ileum being stuck in the umbilical defect. The loop of ileum was freed from the umbilicus which demonstrated open ends of safety pin piercing out of bowel lumen. The enterotomy followed by removal of safety pin was performed.

  13. Open Safety Pin Ingestion Presenting as Incarcerated Umbilical Hernia

    OpenAIRE

    Bilal Mirza; Afzal Sheikh

    2011-01-01

    Foreign body ingestion is common in children. Sharp foreign bodies are potentially harmful and can result various complications. An 8-month-old infant presented with incarcerated umbilical hernia. With a suspicion of strangulation, operation was performed that revealed a loop of ileum being stuck in the umbilical defect. The loop of ileum was freed from the umbilicus which demonstrated open ends of safety pin piercing out of bowel lumen. The enterotomy followed by removal of safety pin was p...

  14. Open Safety Pin Ingestion Presenting as Incarcerated Umbilical Hernia

    Directory of Open Access Journals (Sweden)

    Bilal Mirza

    2011-11-01

    Full Text Available Foreign body ingestion is common in children. Sharp foreign bodies are potentially harmful and can result various complications. An 8-month-old infant presented with incarcerated umbilical hernia. With a suspicion of strangulation, operation was performed that revealed a loop of ileum being stuck in the umbilical defect. The loop of ileum was freed from the umbilicus which demonstrated open ends of safety pin piercing out of bowel lumen. The enterotomy followed by removal of safety pin was performed.

  15. AtPIN: Arabidopsis thaliana Protein Interaction Network

    Directory of Open Access Journals (Sweden)

    Silva-Filho Marcio C

    2009-12-01

    Full Text Available Abstract Background Protein-protein interactions (PPIs constitute one of the most crucial conditions to sustain life in living organisms. To study PPI in Arabidopsis thaliana we have developed AtPIN, a database and web interface for searching and building interaction networks based on publicly available protein-protein interaction datasets. Description All interactions were divided into experimentally demonstrated or predicted. The PPIs in the AtPIN database present a cellular compartment classification (C3 which divides the PPI into 4 classes according to its interaction evidence and subcellular localization. It has been shown in the literature that a pair of genuine interacting proteins are generally expected to have a common cellular role and proteins that have common interaction partners have a high chance of sharing a common function. In AtPIN, due to its integrative profile, the reliability index for a reported PPI can be postulated in terms of the proportion of interaction partners that two proteins have in common. For this, we implement the Functional Similarity Weight (FSW calculation for all first level interactions present in AtPIN database. In order to identify target proteins of cytosolic glutamyl-tRNA synthetase (Cyt-gluRS (AT5G26710 we combined two approaches, AtPIN search and yeast two-hybrid screening. Interestingly, the proteins glutamine synthetase (AT5G35630, a disease resistance protein (AT3G50950 and a zinc finger protein (AT5G24930, which has been predicted as target proteins for Cyt-gluRS by AtPIN, were also detected in the experimental screening. Conclusions AtPIN is a friendly and easy-to-use tool that aggregates information on Arabidopsis thaliana PPIs, ontology, and sub-cellular localization, and might be a useful and reliable strategy to map protein-protein interactions in Arabidopsis. AtPIN can be accessed at http://bioinfo.esalq.usp.br/atpin.

  16. ISOLTRAP pins down masses of exotic nuclides

    CERN Document Server

    Blaum, Klaus; Beck, D; Bollen, G; Brodeur, M; Delahaye, P; George, S; Guenaut, C; Herfurth, F; Herlert, Alexander; Kellerbauer, A G; Kluge, H J; Lunney, M D; Mukherjee, M; Rodríguez, D; Schwarz, S; Schweikhard, L; Yazidjian, C

    2005-01-01

    The mass of radionuclides contribute to a variety of fundamental studies including tests of the weak interaction and the standard model. The limits of mass measurements on exotic nuclides have been extended considerably by the Penning-trap mass spectrometer ISOLTRAP at the ISOLDE facility at CERN. Recent ISOLTRAP measurements are summarized and current technical improvements are outlined.

  17. A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

    Institute of Scientific and Technical Information of China (English)

    Credence Systems Corporation

    2004-01-01

    @@ (上接第9期51页) Figure 3:3 different pins types which cover a wide range of requirements: - DPIN: The digital mixed signal pin for high speed digital requirements - VPIN digital mixed-signal pin with high voltage digital test capability. With the 30 V swing and 50 MHz data rate the pin fits excellent for automotive requirements.

  18. Dipentamethylene thiuram monosulfide is a novel inhibitor of Pin1

    Energy Technology Data Exchange (ETDEWEB)

    Tatara, Yota; Lin, Yi-Chin; Bamba, Yoshimasa; Mori, Tadashi [Molecular Enzymology, Department of Molecular and Cell Biology, Graduate School of Agricultural Science, Tohoku University, 1-1 Amamiya, Tsutsumidori, Aoba, Sendai, Miyagi 981-8555 (Japan); Uchida, Takafumi, E-mail: uchidat@biochem.tohoku.ac.jp [Molecular Enzymology, Department of Molecular and Cell Biology, Graduate School of Agricultural Science, Tohoku University, 1-1 Amamiya, Tsutsumidori, Aoba, Sendai, Miyagi 981-8555 (Japan)

    2009-07-03

    Pin1 is involved in eukaryotic cell proliferation by changing the structure and function of phosphorylated proteins. PiB, the Pin1 specific inhibitor, blocks cancer cell proliferation. However, low solubility of PiB in DMSO has limited studies of its effectiveness. We screened for additional Pin1 inhibitors and identified the DMSO-soluble compound dipentamethylene thiuram monosulfide (DTM) that inhibits Pin1 activity with an EC50 value of 4.1 {mu}M. Molecular modeling and enzyme kinetic analysis indicated that DTM competitively inhibits Pin1 activity, with a K{sub i} value of 0.05 {mu}M. The K{sub D} value of DTM with Pin1 was determined to be 0.06 {mu}M by SPR technology. Moreover, DTM specifically inhibited peptidyl-prolyl cis/trans isomerase activity in HeLa cells. FACS analysis showed that DTM induced G0 arrest of the HCT116 cells. Our results suggest that DTM has the potential to guide the development of novel antifungal and/or anticancer drugs.

  19. Self-pinning of a nanosuspension droplet: Molecular dynamics simulations

    Science.gov (United States)

    Shi, Baiou; Webb, Edmund B.

    2016-07-01

    Results are presented from molecular dynamics simulations of Pb(l) nanodroplets containing dispersed Cu nanoparticles (NPs) and spreading on solid surfaces. Three-dimensional simulations are employed throughout, but droplet spreading and pinning are reduced to two-dimensional processes by modeling cylindrical NPs in cylindrical droplets; NPs have radius RNP≅3 nm while droplets have initial R0≅42 nm . At low particle loading explored here, NPs in sufficient proximity to the initial solid-droplet interface are drawn into advancing contact lines; entrained NPs eventually bind with the underlying substrate. For relatively low advancing contact angle θadv, self-pinning on entrained NPs occurs; for higher θadv, depinning is observed. Self-pinning and depinning cases are compared and forces on NPs at the contact line are computed during a depinning event. Though significant flow in the droplet occurs in close proximity to the particle during depinning, resultant forces are relatively low. Instead, forces due to liquid atoms confined between the particles and substrate dominate the forces on NPs; that is, for the NP size studied here, forces are interface dominated. For pinning cases, a precursor wetting film advances ahead of the pinned contact line but at a significantly slower rate than for a pure droplet. This is because the precursor film is a bilayer of liquid atoms on the substrate surface but it is instead a monolayer film as it crosses over pinning particles; thus, mass delivery to the bilayer structure is impeded.

  20. Pinned vortex hopping in a neutron star crust

    CERN Document Server

    Haskell, Brynmor

    2015-01-01

    The motion of superfluid vortices in a neutron star crust is at the heart of most theories of pulsar glitches. Pinning of vortices to ions can decouple the superfluid from the crust and create a reservoir of angular momentum. Sudden large scale unpinning can lead to an observable glitch. In this paper we investigate the scattering of a free vortex off a pinning potential and calculate its mean free path, in order to assess whether unpinned vortices can skip multiple pinning sites and come close enough to their neighbours to trigger avalanches, or whether they simply hop from one pinning site to another giving rise to a more gradual creep. We find that there is a significant range of parameter space in which avalanches can be triggered, thus supporting the hypothesis that they may lie at the origin of pulsar glitches. For realistic values of the pinning force and superfluid drag parameters we find that avalanches are more likely in the higher density regions of the crust where pinning is stronger. Physical dif...

  1. Dipentamethylene thiuram monosulfide is a novel inhibitor of Pin1.

    Science.gov (United States)

    Tatara, Yota; Lin, Yi-Chin; Bamba, Yoshimasa; Mori, Tadashi; Uchida, Takafumi

    2009-07-03

    Pin1 is involved in eukaryotic cell proliferation by changing the structure and function of phosphorylated proteins. PiB, the Pin1 specific inhibitor, blocks cancer cell proliferation. However, low solubility of PiB in DMSO has limited studies of its effectiveness. We screened for additional Pin1 inhibitors and identified the DMSO-soluble compound dipentamethylene thiuram monosulfide (DTM) that inhibits Pin1 activity with an EC50 value of 4.1 microM. Molecular modeling and enzyme kinetic analysis indicated that DTM competitively inhibits Pin1 activity, with a K(i) value of 0.05 microM. The K(D) value of DTM with Pin1 was determined to be 0.06 microM by SPR technology. Moreover, DTM specifically inhibited peptidyl-prolyl cis/trans isomerase activity in HeLa cells. FACS analysis showed that DTM induced G0 arrest of the HCT116 cells. Our results suggest that DTM has the potential to guide the development of novel antifungal and/or anticancer drugs.

  2. Repeat biopsy in patients with initial diagnosis of PIN; La biopsia ripetuta nei pazienti con diagnosi iniziale di PIN

    Energy Technology Data Exchange (ETDEWEB)

    De Matteis, Massimo [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Radiologia Albertoni; Poggi, Cristina; De Martino, Antonietta; Pavlica, Pietro [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Radiologia Palagi, Dipartimento area radiologica; Corti, Barbara [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Anatomia ed istologia patologica, Dipartimento oncologico ed ematologico; Barozzi, Libero [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Radiologia d' urgenza, Dipartimento emergenze ed accettazione

    2005-09-15

    Purpose. Prostatic intra-epithelial neoplasia (PIN) is considered a pre-malignant lesion and the main precursor of invasive prostatic adenocarcinoma. A PIN diagnosis established by prostate needle biopsy poses a difficult clinical management. problem. We retrospectively reviewed our three-year experience in order to identify criteria for referring patients to repeat biopsy. Materials and methods. We reviewed the repeat biopsy records of 72 patients in whom PIN had been detected on initial US-guided needle biopsy of the prostate. All the patients had a minimum of 6 biopsy cores taken, and they all had PSA > 4 ng/ml. Results. Adenocarcinoma was detected in 15 patients out of 50 (30%) with an initial diagnosis of low-grade PIN and in 10 patients out of 22 (45.4%) with high grade PIN, in 7 out of 18 (39%) in whom PSA levels had decreased during the observation interval, in 16 patients out of 46 (35%) in whom the PSA had increased and in 2 patients out of 8 (25%) with stable PSA. Conclusions. Our results seem to confirm that PIN can be considered a precursor of prostatic adenocarcinoma or a histological alteration often associated with it. Patients with low-grade PIN and particularly those with high-grade PIN should be regularly subjected to repeat biopsy at short intervals due to the high frequency of the final diagnosis of carcinoma. No agreement has been reached on the time interval between the first and the second biopsy. The PSA changes during the observation period are not a statistically significant parameter to suggest the repetition of prostatic biopsy. [Italian] Scopo. La neoplasia prostatica intraepiteliale (PIN) e considerata una lesione premaligna ed il precursore principale dell'adenocarcinoma prostatico infiltrante. La diagnosi di PIN ottenuta con l'agobiopsia della prostata rappresenta un difficile problema gestionale clinico. In una valutazione retrospettiva della nostra esperienza di 3 anni si e cercato di individuare i criteri che possano

  3. Pin-Hole Luminosity Monitor with Feedback

    Science.gov (United States)

    Norem, James H.; Spencer, James E.

    Previously, the generalized luminosity { L} was defined and calculated for all incident channels based on an NLC e+e- design. Alternatives were then considered to improve the differing beam-beam effects in the e-e-, eγ and γγ channels. Regardless of the channel, there was a large flux of outgoing, high energy photons that were produced from the beam-beam interaction e.g. beamstrahlung that needs to be disposed of and whose flux depended on { L}. One approach to this problem is to consider it a resource and attempt to take advantage of it by disposing of these straight-ahead photons in more useful ways than simply dumping them. While there are many options for monitoring the luminosity, any method that allows feedback and optimization in real time and in a non-intercepting and non-interfering way during normal data taking is extremely important - especially if it provides other capabilities such as high resolution tuning of spot sizes and can be used for all incident channels without essential modifications to their setup. Our "pin-hole" camera appears to be such a device if it can be made to work with high energy photons in ways that are compatible with the many other constraints and demands on space around the interaction region. The basis for using this method is that it has, in principle, the inherent resolution and bandwidth to monitor the very small spot sizes and their stabilities that are required for very high, integrated luminosity. While there are many possible, simultaneous uses of these outgoing photon beams, we limit our discussion to a single, blind, proof-of-principle experiment that was done on the FFTB line at SLAC to certify the concept of a camera obscura for high energy photons.

  4. Interplay between collective pinning and artificial defects on domain wall propagation in Co/Pt multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez-Rodriguez, G; Hierro-Rodriguez, A; Perez-Junquera, A; Montenegro, N; Alameda, J M; Velez, M [Dept. Fisica, Universidad de Oviedo-CINN, 33007 Oviedo (Spain); Menendez, J L [Centro de Investigacion en Nanomateriales y Nanotecnologia (CINN). Principado de Asturias-Consejo Superior de Investigaciones Cientificas (CSIC)-Univ. Oviedo -UO, Parque Tecnologico de Asturias, 33428 Llanera (Spain); Ravelosona, D, E-mail: mvelez@uniovi.e [Institut d' Electronique Fondamentale, UMR CNRS 8622, Univ. Paris Sud, 91405 Orsay Cedex (France)

    2010-08-04

    The interplay between collective pinning on intrinsic structural defects and artificial pinning at a patterned hole is studied in magnetic multilayers with perpendicular anisotropy. The pinning strength of a patterned hole is measured through its efficiency to stop domain wall (DW) propagation into a consecutive unpatterned nanowire section (using antisymmetric magnetoresistance to detect the direction of DW propagation) whereas collective pinning is characterized by the field dependence of DW velocity. Close to room temperature, collective pinning becomes weaker than artificial pinning so that pinning at the hole compensates nucleation-pad geometry, blocking DW propagation across the nanowire.

  5. Melting of Ice under Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Schwegler, E; Sharma, M; Gygi, F; Galli, G

    2008-07-31

    The melting of ice under pressure is investigated with a series of first principles molecular dynamics simulations. In particular, a two-phase approach is used to determine the melting temperature of the ice-VII phase in the range of 10 to 50 GPa. Our computed melting temperatures are consistent with existing diamond anvil cell experiments. We find that for pressures between 10 to 40 GPa, ice melts as a molecular solid. For pressures above {approx}45 GPa there is a sharp increase in the slope of the melting curve due to the presence of molecular dissociation and proton diffusion in the solid, prior to melting. The onset of significant proton diffusion in ice-VII as a function of increasing temperature is found to be gradual and bears many similarities to that of a type-II superionic solid.

  6. Melt processing of bulk high Tc superconductors and their application

    Science.gov (United States)

    Murakami, M.; Oyama, T.; Fujimoto, H.; Gotoh, S.; Yamaguchi, K.

    1991-03-01

    The authors report a melt-powder-melt-growth (MPMG) process which results in high Jc for bulk Y-Ba-Cu-O superconductors. The Y-Ba-Cu-O pellets or powders are melt quenched. The quenched plates are crushed into powder and mixed well. The powder is then compacted into desired shapes, remelted, and slowly cooled in a thermal gradient. When the starting composition is changed from the 1:2:3 stoichiometry toward the Y2BaCuO5(211) rich region, the 211 inclusions can be dispersed in the YBa2Cu3O(x) matrix, which contributes to increases in both flux pinning force and fracture toughness. A Jc value exceeding 3 x 108 A/sq m has been achieved at 77 K and 1 T. Another attractive feature of the MPMG process is that other components such as fine Ag powders can be added during solid-state mixing. Fine dispersion of Ag particles can effectively reduce the amount of cracking. MPMG-processed Y-Ba-Cu-O with Ag doping can levitate a mass of 3-kg at 1-mm height using a repulsive force against a 0.4-T magnet. A noncontacting rotation device such as a magnetic bearing can be made utilizing bulk high-Jc materials. A superconducting permanent magnet is also a promising candidate for future application. MPMG-processed Y-Ba-Cu-O can generate 0.25 T at 77 K.

  7. Enhancement of flux pinning properties in nanosized MgO added Bi-2212 superconductor through neutron irradiation

    Science.gov (United States)

    Mohiju, Zaahidah'Atiqah; Hamid, Nasri A.; Abdullah, Yusof

    2017-01-01

    For superconducting material to maintain high critical current density, Jc in any applications, effective flux pinning centers are needed. The addition of small size MgO particles in bulk Bi2Sr2CaCu2O8 (Bi-2212) superconductor has been proven to enhance the effective flux pinning centers in the superconducting material by creating a desired microstructure with appropriate defects. To further enhance the pinning properties, radiation is one of the convenient ways to improve the microstructure of the material that has correlation with basic properties of superconductors. Neutron irradiation is one of the niche techniques that can be used to perform the task. Defects with larger radius have dimension comparable to the coherence length of the material and thus improved its superconducting properties. In this paper, a small amount of nanosized MgO particles was used to create defects in the Bi-2212 superconducting material. The Bi-2212/MgO compounds were heat treated, followed by partial melting and slow cooling. Part of the samples was subjected to neutron irradiation using the TRIGA-MARK-II research reactor at the Malaysian Nuclear Agency. Characterization of non-irradiated and irradiated samples was performed via the temperature dependence on electrical resistance measurements, X-ray Diffraction Patterns (XRD), and Scanning Electron Microscopy (SEM) with Energy Dispersive X-ray (EDX) analysis. From the analysis, there was changed in the critical current density and transition temperature of samples subjected to neutron irradiation due to formation of point defects in the microstructure. Higher critical current density indicates better flux pinning properties in the Bi-2212/MgO compounds.

  8. Role of the Arabidopsis PIN6 Auxin Transporter in Auxin Homeostasis and Auxin-Mediated Development

    OpenAIRE

    2013-01-01

    Plant-specific PIN-formed (PIN) efflux transporters for the plant hormone auxin are required for tissue-specific directional auxin transport and cellular auxin homeostasis. The Arabidopsis PIN protein family has been shown to play important roles in developmental processes such as embryogenesis, organogenesis, vascular tissue differentiation, root meristem patterning and tropic growth. Here we analyzed roles of the less characterised Arabidopsis PIN6 auxin transporter. PIN6 is auxin-inducible...

  9. THE PROPERTIES AND MICROSTRUCTURE OF NB-47TI SUPERCONDUCTOR WITH MAGNETIC PINNING CENTERS.

    Energy Technology Data Exchange (ETDEWEB)

    MOTOWIDLO,L.R.RUDZIAK,M.D.WONG,T.COOLEY,L.D.LEE,P.J.

    2004-02-04

    We have investigated Nb-47Ti multifilament wire with artificial pinning centers (APC). The superconducting properties and proximity effect in wires with ferromagnetic and non-magnetic pins will be discussed. Magnetization and transport measurements will be presented and the pinning characteristics will be discussed as a function of magnetic field, temperature and volume percent pins. In addition, field emission scanning electron microscopy of the pin nanostructure will be presented.

  10. MULTIPLE MELTING IN NYLON 1010

    Institute of Scientific and Technical Information of China (English)

    FU Shuren; CHEN Taoyung

    1983-01-01

    Multiple melting behavior of nylon 1010 has been investigated by using DSC instrument. Effects of partial scanning, partial scanning and annealing, heating rate, cooling rate and stepwise annealing on the melting curve were studied. Experimental results indicate that the sample undergoes a process of continuous melting and recrystallization during DSC scanning. Nylon 1010 contains a distribution of crystallites of different degrees of perfection which is strongly dependent on its previous thermal history. From the structural reorganization point of view, the origin of double and multiple peaks of the melting curve is explained.

  11. Delayed Fission Product Gamma-Ray Transmission Through Low Enriched UO2 Fuel Pin Lattices in Air

    Energy Technology Data Exchange (ETDEWEB)

    Trumbull, TH [Rensselaer Polytechnic Inst., Troy, NY (United States)

    2004-10-18

    The transmission of delayed fission-product gamma rays through various arrangements of low-enriched UO2 fuel pin lattices in an air medium was studied. Experimental measurements, point-kernel and Monte Carlo photon transport calculations were performed to demonstrate the shielding effect of ordered lattices of fuel pins on the resulting gamma-ray dose to a detector outside the lattice. The variation of the gamma-ray dose on the outside of the lattice as a function of radial position, the so-called “channeling” effect, was analyzed. Techniques for performing experimental measurements and data reduction at Rensselaer Polytechnic Institute’s Reactor Critical Facility (RCF) were derived. An experimental apparatus was constructed to hold the arrangements of fuel pins for the measurements. A gamma-ray spectroscopy system consisting of a sodium-iodide scintillation detector was used to collect data. Measurements were made with and without a collimator installed. A point-kernel transport code was developed to map the radial dependence of the gamma-ray flux. Input files for the Monte Carlo code, MCNP, were also developed to accurately model the experimental measurements. The results of the calculations were compared to the experimental measurements. In order to determine the delayed fission-product gamma-ray source for the calculations, a technique was developed using a previously written code, DELBG and the reactor state-point data obtained during the experimental measurements. Calculations were performed demonstrating the effects of material homogenization on the gamma-ray transmission through the fuel pin lattice.Homogeneous and heterogeneous calculations were performed for all RCF fuel pin lattices as well as for a typical commercial pressurized water reactor fuel bundle. The results of the study demonstrated the effectiveness of the experimental measurements to isolate the channeling effect of delayed fission-product gamma-rays through lattices of RCF fuel pins

  12. Demonstration of Emitted-Neutron Computed Tomography to Count Fuel Pins

    Energy Technology Data Exchange (ETDEWEB)

    P. A. Hausladen; M. A. Blackston; E. Brubaker; D. L. Chichester; P. Marleau; R. J. Newby

    2012-07-01

    In this paper, we report demonstration of emitted-neutron computed tomography using fast fission neutrons to infer the geometry of sources of special nuclear material (SNM) such as fuel pins. In a proof-of-concept measurement at the Idaho National Laboratory’s (INL’s) Zero Power Physics Reactor (ZPPR) facility, an array of unirradiated Pu MOX fuel rodlets in a soup can were imaged, and a bias defect consisting of a single rodlet containing Pu replaced by one containing depleted uranium (DU) was detected. The imaging system employed in the demonstration is based on a newly constructed array of pixelated neutron detectors that are suitable for arrangement in a close-packed imaging array and whose active volume consists of liquid scintillator EJ-309 which allows neutron-gamma discrimination via pulse shape to enable pure fast-neutron imaging. The imaging array was used along with a radial collimator aperture in order to perform high quality fast-neutron imaging where tomographic reconstruction of slices through an object resolve neutron sources similar in dimension to a fuel pellet, or about 1 cm. Measurements were performed at Oak Ridge National Laboratory (ORNL) with neutron sources in addition to those performed at the INL’s ZPPR facility with Pu MOX fuel rodlets. An analogous capability to detect single-pin defects in spent fuel assemblies would be desirable, such as for safeguards verification measurements of spent fuel assemblies just prior to transferring them from the spent fuel cooling pool to long term dry cask storage. This paper describes the design and construction of the present imager, characterization measurements with neutron sources at ORNL, measurements with SNM at INL’s ZPPR facility, and feasibility of building an analogous imager for spent fuel measurements.

  13. Flux Pinning in Superconducting Niobium-Titanium Alloys

    Science.gov (United States)

    McKinnell, James Charles

    1990-01-01

    By studying Nb-Ti alloys from Nb44wt%Ti to Nb62wt%Ti the low field (2T) current density has been raised from 6500A/mm^2 (4.2^ circK) with standard Nb46.5wt%Ti to 7400A/mm ^2 with Nb58wt%Ti. When standard processing sequences were used, the alloys containing more than 46.5wt%Ti exhibited non-uniform microstructures following a precipitation heat treatment and the hardness rose from 200 DPN to over 300 DPN. By increasing the cold work prior to heat treatment the non-uniform precipitation was avoided. The amount of cold work needed prior to heat treatment to suppress non-uniform precipitation increased as the Ti content of the alloy increased. The volume fraction of precipitate produced during a given heat treatment also increased as the Ti content of the alloy increased. As the Ti content increased, the peak in the reduced pinning force curve shifted from b = 0.5 to b = 0.25. In order to determine whether the change in the flux pinning properties was due to the change in microstructure or due to enhanced Delta H_{c} pinning as the Ti content was increased, a set of wires with similar microstructures was developed. Their flux pinning behavior showed that the higher Ti alloys have pinning force curves which peak at progressively lower reduced fields. Thus Delta H_{c} pinning becomes the dominant pinning mechanism as the Ti content is increased.

  14. Melt pool dynamics during selective electron beam melting

    Science.gov (United States)

    Scharowsky, T.; Osmanlic, F.; Singer, R. F.; Körner, C.

    2014-03-01

    Electron beam melting is a promising additive manufacturing technique for metal parts. Nevertheless, the process is still poorly understood making further investigations indispensable to allow a prediction of the part's quality. To improve the understanding of the process especially the beam powder interaction, process observation at the relevant time scale is necessary. Due to the difficult accessibility of the building area, the high temperatures, radiation and the very high scanning speeds during the melting process the observation requires an augmented effort in the observation equipment. A high speed camera in combination with an illumination laser, band pass filter and mirror system is suitable for the observation of the electron beam melting process. The equipment allows to observe the melting process with a high spatial and temporal resolution. In this paper the adjustment of the equipment and results of the lifetime and the oscillation frequencies of the melt pool for a simple geometry are presented.

  15. Fabrication Facilities

    Data.gov (United States)

    Federal Laboratory Consortium — The Fabrication Facilities are a direct result of years of testing support. Through years of experience, the three fabrication facilities (Fort Hood, Fort Lewis, and...

  16. Effect of Welding Speed and Tool Pin Geometry on Impact Strength in Friction Stir Welding of Aluminium 6101 T6 Alloy

    Directory of Open Access Journals (Sweden)

    Singh Rajbir

    2016-01-01

    Full Text Available Friction stir welding (FSW process is a solid state joining method in which the material that is being welded does not melt and recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters play a major role in deciding the joint characteristics. In this investigation the effect of welding speed and tool pin geometry in friction stir welds of Aluminium alloy was studied. The welded joints were made of Aluminium alloy AA 6101 T6 strips of 6mm thickness with different tool pin profile (Cylindrical, Taper cylindrical, Square and Taper Square. All the welding operations were done at the room temperature. Charpy tests were carried out to find the impact strength. From this investigation it is found that strength is superior with taper square tool pin profile than cylindrical, taper cylindrical and square tool pin profile. The pieces weld at rotational speed of 1200 r.p.m and welding speed of 70mm/min using taper square tool have higher strength.

  17. Facility Microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Z.; Walling, R.; Miller, N.; Du, P.; Nelson, K.

    2005-05-01

    Microgrids are receiving a considerable interest from the power industry, partly because their business and technical structure shows promise as a means of taking full advantage of distributed generation. This report investigates three issues associated with facility microgrids: (1) Multiple-distributed generation facility microgrids' unintentional islanding protection, (2) Facility microgrids' response to bulk grid disturbances, and (3) Facility microgrids' intentional islanding.

  18. Alpha particles spectrometer with photodiode PIN; Espectrometro de particulas alfa con fotodiodo PIN

    Energy Technology Data Exchange (ETDEWEB)

    Chacon R, A.; Hernandez V, R.; Hernandez D, V. M.; Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidades Academicas de Estudios Nucleares e Ingenieria Electrica, Calle Cipres No. 10, Fracc. La Penuela, 09869 Zacatecas (Mexico); Ramirez G, J. [Instituto Nacional de Estadistica Geografia e Informatica, Direccion General de Innovacion y Tecnologia de Informacion, Av. Heroes de Nacozari Sur 2301, Fracc. Jardines del Parque, 20276 Aguascalientes (Mexico)], e-mail: achruiz@hotmail.com

    2009-10-15

    The radiation propagates in form of electromagnetic waves or corpuscular radiation; if the radiation energy causes ionization in environment that crosses it is considered ionizing radiation. To detect radiation several detectors types are used, if the radiation are alpha particles are used detectors proportional type or trace elements. In this work the design results, construction and tests of an alpha particles spectrometer are presented, which was designed starting from a photodiode PIN type. The system design was simulated with a code for electronic circuits. With results of simulation phase was constructed the electronic phase that is coupled to a multichannel analyzer. The resulting electronic is evaluated analyzing the electronic circuit performance before an alphas triple source and alpha radiation that produce two smoke detectors of domestic use. On the tests phase we find that the system allows obtain, in a multichannel, the pulses height spectrum, with which we calibrate the system. (Author)

  19. Effects of ZrB2 on substructure and wear properties of laser melted in situ ZrB2p/6061Al composites

    Science.gov (United States)

    Zeng, Yida; Chao, Yuhjin; Luo, Zhen; Cai, Yangchuan; Huang, Yongxian

    2016-03-01

    Aluminum matrix composites reinforced by in situ ZrB2 particles were successfully fabricated from an Al-KBF4-K2ZrF6 system via a direct melt reaction. A laser surface melting strategy is used to improve the surface strength of the in situ ZrB2p/6061Al composite, which includes a series of laser-melted composites with different laser power processed by a 2 kW YAG laser generator. XRD and EDS results demonstrated the existence of ZrB2 nanoparticles in the composite. After laser melting, the penetration depth of the molten pool increases with increasing power density. OM and SEM analysis indicate that the laser melting process yields narrower cellular spacing of the matrix and partly disperses the ZrB2 particle clusters. Compared with laser-melted matrix alloys, the crystal orientations near the melted layers edge of the composite are almost random due to heterogeneous nucleation in the melt and the pinning effect of laser-dispersed ZrB2 nanoparticles at the solidification front. Wear test results show that the laser melted layer performs better at wear resistance than both the substrate and the matrix AA6061 by measuring wear mass loss. Compared with composite samples prepared without laser melting, the wear mass loss of the laser melted composites decreased from 61 to 56 mg under a load of 98 N for 60 min.

  20. Beyond the Melting Pot Reconsidered.

    Science.gov (United States)

    Anderson, Elijah

    2000-01-01

    Discusses the 1963 book, "Beyond the Melting Pot," which suggested that eventually the problem of different ethnicities in the U.S. would be resolved and society would become one melting pot. Examines how changes in immigration and economic structures have affected the issue, noting the devastating effect of the dominant culture's…

  1. Pin1 and neurodegeneration: a new player for prion disorders?

    Directory of Open Access Journals (Sweden)

    Elisa Isopi

    2015-07-01

    Full Text Available Pin1 is a peptidyl-prolyl isomerase that catalyzes the cis/trans conversion of phosphorylated proteins at serine or threonine residues which precede a proline. The peptidyl-prolyl isomerization induces a conformational change of the proteins involved in cell signaling process. Pin1 dysregulation has been associated with some neurodegenerative disorders such as Alzheimer's disease, Parkinson's disease and Huntington's disease. Proline-directed phosphorylation is a common regulator of these pathologies and a recent work showed that it is also involved in prion disorders. In fact, prion protein phosphorylation at the Ser-43-Pro motif induces prion protein conversion into a disease-associated form. Furthermore, phosphorylation at Ser-43-Pro has been observed to increase in the cerebral spinal fluid of sporadic Creutzfeldt-Jakob Disease patients. These findings provide new insights into the pathogenesis of prion disorders, suggesting Pin1 as a potential new player in the disease. In this paper, we review the mechanisms underlying Pin1 involvement in the aforementioned neurodegenerative pathologies focusing on the potential role of Pin1 in prion disorders.

  2. Exchange anisotropy pinning of a standing spin-wave mode

    Science.gov (United States)

    Magaraggia, R.; Kennewell, K.; Kostylev, M.; Stamps, R. L.; Ali, M.; Greig, D.; Hickey, B. J.; Marrows, C. H.

    2011-02-01

    Standing spin waves in a thin film are used as sensitive probes of interface pinning induced by an antiferromagnet through exchange anisotropy. Using coplanar waveguide ferromagnetic resonance, pinning of the lowest energy spin-wave thickness mode in Ni80Fe20/Ir25Mn75 exchange-biased bilayers was studied for a range of Ir25Mn75 thicknesses. We show that pinning of the standing mode can be used to amplify, relative to the fundamental resonance, frequency shifts associated with exchange bias. The shifts provide a unique “fingerprint” of the exchange bias and can be interpreted in terms of an effective ferromagnetic film thickness and ferromagnet-antiferromagnet interface anisotropy. Thermal effects are studied for ultrathin antiferromagnetic Ir25Mn75 thicknesses, and the onset of bias is correlated with changes in the pinning fields. The pinning strength magnitude is found to grow with cooling of the sample, while the effective ferromagnetic film thickness simultaneously decreases. These results suggest that exchange bias involves some deformation of magnetic order in the interface region.

  3. Research on the Pin Fin Efficiency and Structure

    Directory of Open Access Journals (Sweden)

    Fan Bailin

    2013-06-01

    Full Text Available The performance of pin fin heat sink can be to measure through the temperature field. The temperature field and efficiency of the Pin Fin were analyzed, Pin fin efficiency curve was drowned also the distribution of the temperature field along the length of the pin fin curve was drawn. Thermal resistance was composed by thermal resistance of Aluminum substrate、 thermal resistance of convective heat transfer and the thermal resistance of the cooling liquid. The change rule was studied through the calculation on Aluminum plate thermal resistance、 thermal resistance of convective heat transfer and the thermal resistance of the cooling liquid. Its change regularity was simulated by toolbox In the MATLAB, and it was found that thermal resistance of convective heat transfer effect on the efficiency was most obvious in a certain amount of the heat and flow for thermal resistance of the Pin-fin radiator under the premise. The structural parameters of radiator were related to the size of thermal resistance.

  4. A Flux-Pinning Mechanism for Segment Assembly and Alignment

    Science.gov (United States)

    Gersh-Range, Jessica A.; Arnold, William R.; Peck, Mason A.; Stahl, H. Philip

    2011-01-01

    Currently, the most compelling astrophysics questions include how planets and the first stars formed and whether there are protostellar disks that contain large organic molecules. Although answering these questions requires space telescopes with apertures of at least 10 meters, such large primaries are challenging to construct by scaling up previous designs; the limited capacity of a launch vehicle bounds the maximum diameter of a monolithic primary, and beyond a certain size, deployable telescopes cannot fit in current launch vehicle fairings. One potential solution is connecting the primary mirror segments edgewise using flux-pinning mechanisms, which are analogous to non-contacting damped springs. In the baseline design, a flux-pinning mechanism consists of a magnet and a superconductor separated by a predetermined gap, with the damping adjusted by placing aluminum near the interface. Since flux pinning is possible only when the superconductor is cooled below a critical temperature, flux-pinning mechanisms are uniquely suited for cryogenic space telescopes. By placing these mechanisms along the edges of the mirror segments, a primary can be built up over time. Since flux pinning requires no mechanical deployments, the assembly process could be robotic or use some other non-contacting scheme. Advantages of this approach include scalability and passive stability.

  5. Pin1 inhibitor Juglone prevents diabetic vascular dysfunction.

    Science.gov (United States)

    Costantino, Sarah; Paneni, Francesco; Lüscher, Thomas F; Cosentino, Francesco

    2016-01-15

    Atherosclerosis is a major cause of mortality in patients with diabetes. However, novel breakthrough therapies have yet to be approved in this setting. Prolyl-isomerase-1 (Pin1) is emerging as a key molecule implicated in vascular oxidative stress and inflammation. In the present study, we investigate whether pharmacological inhibition of Pin1 may protect against diabetes-induced oxidative stress, endothelial dysfunction and vascular inflammation. Experiments were performed in human aortic endothelial cells (HAECs) exposed to normal (5 mmol/L) or high glucose (25 mmol/L) concentrations, in the presence of Pin1 inhibitor Juglone (10 μM) or vehicle (kB-dependent inflammatory signatures were determined both in HAECs and aortas from diabetic mice. In HAECs, ambient hyperglycemia increased mitochondrial superoxide anion generation while treatment with Juglone prevented this phenomenon. Pharmacological inhibition of Pin1 also preserved mitochondrial integrity, nitric oxide availability and endothelial expression of adhesion molecules. Interestingly enough, endothelial dysfunction, oxidative stress and NF-kB-driven inflammation were significantly attenuated in diabetic mice chronically treated with Juglone as compared to vehicle-treated animals. Pharmacological inhibition of Pin1 by Juglone prevents hyperglycemia-induced vascular dysfunction. Taken together, our findings may set the stage for novel therapeutic approaches to prevent vascular complications in patients with diabetes. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  6. Posttranslational modification and trafficking of PIN auxin efflux carriers.

    Science.gov (United States)

    Löfke, Christian; Luschnig, Christian; Kleine-Vehn, Jürgen

    2013-01-01

    Cell-to-cell communication is absolutely essential for multicellular organisms. Both animals and plants use chemicals called hormones for intercellular signaling. However, multicellularity of plants and animals has evolved independently, which led to establishment of distinct strategies in order to cope with variations in an ever-changing environment. The phytohormone auxin is crucial to plant development and patterning. PIN auxin efflux carrier-driven polar auxin transport regulates plant development as it controls asymmetric auxin distribution (auxin gradients), which in turn modulates a wide range of developmental processes. Internal and external cues trigger a number of posttranslational PIN auxin carrier modifications that were demonstrated to decisively influence variations in adaptive growth responses. In this review, we highlight recent advances in the analysis of posttranslational modification of PIN auxin efflux carriers, such as phosphorylation and ubiquitylation, and discuss their eminent role in directional vesicle trafficking, PIN protein de-/stabilization and auxin transport activity. We conclude with updated models, in which we attempt to integrate the mechanistic relevance of posttranslational modifications of PIN auxin carriers for the dynamic nature of plant development.

  7. Silicide Schottky Contacts to Silicon: Screened Pinning at Defect Levels

    Energy Technology Data Exchange (ETDEWEB)

    Drummond, T.J.

    1999-03-11

    Silicide Schottky contacts can be as large as 0.955 eV (E{sub v} + 0.165 eV) on n-type silicon and as large as 1.05 eV (E{sub c} {minus} 0.07 eV) on p-type silicon. Current models of Schottky barrier formation do not provide a satisfactory explanation of occurrence of this wide variation. A model for understanding Schottky contacts via screened pinning at defect levels is presented. In the present paper it is shown that most transition metal silicides are pinned approximately 0.48 eV above the valence band by interstitial Si clusters. Rare earth disilicides pin close to the divacancy acceptor level 0.41 eV below the conduction band edge while high work function silicides of Ir and Pt pin close to the divacancy donor level 0.21 eV above the valence band edge. Selection of a particular defect pinning level depends strongly on the relative positions of the silicide work function and the defect energy level on an absolute energy scale.

  8. MELT RATE FURNACE TESTING FOR SLUDGE BATCH 5 FRIT OPTIMIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D; Fox, K; Pickenheim, B; Stone, M

    2008-10-03

    Savannah River National Laboratory (SRNL) was requested to provide the Defense Waste Processing Facility (DWPF) with a frit composition for Sludge Batch 5 (SB5) to optimize processing. A series of experiments were designed for testing in the Melt Rate Furnace (MRF). This dry fed tool can be used to quickly determine relative melt rates for a large number of candidate frit compositions and lead to a selection for further testing. Simulated Sludge Receipt and Adjustment Tank (SRAT) product was made according to the most recent SB5 sludge projections and a series of tests were conducted with frits that covered a range of boron and alkali ratios. Several frits with relatively large projected operating windows indicated melt rates that would not severely impact production. As seen with previous MRF testing, increasing the boron concentration had positive impacts on melt rate on the SB5 system. However, there appears to be maximum values for both boron and sodium above which the there is a negative effect on melt rate. Based on these data and compositional trends, Frit 418 and a specially designed frit (Frit 550) have been selected for additional melt rate testing. Frit 418 and Frit 550 will be run in the Slurry Fed Melt Rate Furnace (SMRF), which is capable of distinguishing rheological properties not detected by the MRF. Frit 418 will be used initially for SB5 processing in DWPF (given its robustness to compositional uncertainty). The Frit 418-SB5 system will provide a baseline from which potential melt rate advantages of Frit 550 can be gauged. The data from SMRF testing will be used to determine whether Frit 550 should be recommended for implementation in DWPF.

  9. Fault rheology beyond frictional melting.

    Science.gov (United States)

    Lavallée, Yan; Hirose, Takehiro; Kendrick, Jackie E; Hess, Kai-Uwe; Dingwell, Donald B

    2015-07-28

    During earthquakes, comminution and frictional heating both contribute to the dissipation of stored energy. With sufficient dissipative heating, melting processes can ensue, yielding the production of frictional melts or "pseudotachylytes." It is commonly assumed that the Newtonian viscosities of such melts control subsequent fault slip resistance. Rock melts, however, are viscoelastic bodies, and, at high strain rates, they exhibit evidence of a glass transition. Here, we present the results of high-velocity friction experiments on a well-characterized melt that demonstrate how slip in melt-bearing faults can be governed by brittle fragmentation phenomena encountered at the glass transition. Slip analysis using models that incorporate viscoelastic responses indicates that even in the presence of melt, slip persists in the solid state until sufficient heat is generated to reduce the viscosity and allow remobilization in the liquid state. Where a rock is present next to the melt, we note that wear of the crystalline wall rock by liquid fragmentation and agglutination also contributes to the brittle component of these experimentally generated pseudotachylytes. We conclude that in the case of pseudotachylyte generation during an earthquake, slip even beyond the onset of frictional melting is not controlled merely by viscosity but rather by an interplay of viscoelastic forces around the glass transition, which involves a response in the brittle/solid regime of these rock melts. We warn of the inadequacy of simple Newtonian viscous analyses and call for the application of more realistic rheological interpretation of pseudotachylyte-bearing fault systems in the evaluation and prediction of their slip dynamics.

  10. The low magnetic field properties of superconducting bulk yttrium barium copper oxide - Sintered versus partially melted material

    Science.gov (United States)

    Hein, R. A.; Hojaji, H.; Barkatt, A.; Shafii, H.; Michael, K. A.; Thorpe, A. N.; Ware, M. F.; Alterescu, S.

    1989-01-01

    A comparison of the low magnetic field properties of sintered (990 C) and partially melted samples (1050 C) has been performed. Changes in the microstructure produced by recrystallization from the melt result in a significant increase in flux pinning at 77 K. Low-frequency (10-100 Hz), low-ac magnetic-field (0.01-9.0 Oe) ac susceptibility data show that gross changes in the loss component accompany the observed changes in microstructure. The effects of applied dc magnetic fields (10-220 Oe) on the ac responses of these microstructures have also been probed.

  11. Creating Usable Pin Array Tactons for Non-Visual Information

    CERN Document Server

    Pietrzak, Thomas; Stephen, Brewster A; Martin, Benoît; Pecci, Isabelle; 10.1109/TOH.2009.6

    2012-01-01

    Spatial information can be difficult to present to a visually impaired computer user. In this paper we examine a new kind of tactile cueing for non-visual interaction as a potential solution, building on earlier work on vibrotactile Tactons. However, unlike vibrotactile Tactons, we use a pin array to stimulate the finger tip. Here, we describe how to design static and dynamic Tactons by defining their basic components. We then present user tests examining how easy it is to distinguish between different forms of pin array Tactons demonstrating accurate Tacton sets to represent directions. These experiments demonstrate usable patterns for static, wave and blinking pin array Tacton sets for guiding a user in one of eight directions. A study is then described that shows the benefits of structuring Tactons to convey information through multiple parameters of the signal. By using multiple independent parameters for a Tacton, this study demonstrates participants perceive more information through a single Tacton. Two...

  12. Pin Tool Geometry Effects in Friction Stir Welding

    Science.gov (United States)

    Querin, J. A.; Rubisoff, H. A.; Schneider, J. A.

    2009-01-01

    In friction stir welding (FSW) there is significant evidence that material can take one of two different flow paths when being displaced from its original position in front of the pin tool to its final position in the wake of the weld. The geometry of the pin tool, along with the process parameters, plays an important role in dictating the path that the material takes. Each flow path will impart a different thermomechanical history on the material, consequently altering the material microstructure and subsequent weld properties. The intention of this research is to isolate the effect that different pin tool attributes have on the flow paths imparted on the FSWed material. Based on published weld tool geometries, a variety of weld tools were fabricated and used to join AA2219. Results from the tensile properties and microstructural characterization will be presented.

  13. Transverse commensurability effect for vortices on periodic pinning arrays

    Energy Technology Data Exchange (ETDEWEB)

    Reichhardt, Charles [Los Alamos National Laboratory; Reichhardt, Cynthia J [Los Alamos National Laboratory

    2008-01-01

    Using computer simulations, we demonstrate a type of commensurability that occurs for vortices moving longitudinally through periodic pinning arrays in the presence of an additional transverse driving force. As a function of vortex density, there is a series of broad maxima in the transverse critical depinning force that do not fall at the matching fields where the number of vortices equals an integer multiple of the number of pinning sites. The commensurability effects are associated with dynamical states in which evenly spaced structures consisting of one or more moving rows of vortices form between rows of pinning sites. Remarkably, the critical transverse depinning force can be more than an order of magnitude larger than the longitudinal depinning force.

  14. Pinning force scaling of electrospun Bi-2212 nanowire networks

    Science.gov (United States)

    Koblischka, Michael R.; Gokhfeld, Denis; Chang, Crosby; Hauet, Thomas; Hartmann, Uwe

    2017-09-01

    Flux pinning forces were determined on different network samples of superconducting Bi2Sr2CaCu2O8 (Bi-2212) nanowires prepared by the electrospinning technique. We employed magnetization data determined by SQUID magnetometry in a wide temperature range 10 K signal prevails. The scaling analysis of the pinning forces was applied to interprete the data obtained. Both pure and Li-doped Bi2212 nanowire networks exhibit a peak position of h0 ∼ 0.11, which is smaller than the expected value of h0 = 0.2 indicating flux pinning at grain boundaries or extended defects. For the flowing currents through such a network, the crystallographic anisotropy and the percolation play an important role, resulting in reduced peak positions as compared to bulk samples.

  15. Control of flux pinning in MOD YBCO coated conductor.

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, W.; Huang, Y.; Li, X.; Kodenkandath, T.; Rupich, M. W.; Schoop, U.; Verebelyi, D. T.; Thieme, C. L. H.; Siegal, E.; Holesinger, T. G.; Maiorov, B.; Civale, L.; Miller, D. J.; Maroni, V. A.; Li, J.; Martin, P. M.; Specht, E. D.; Goyal, A.; Paranthaman, M. P.; American Superconductor Corp.; LANL; ORNL

    2007-06-01

    NTwo different types of defect structures have been identified to be responsible for the enhanced pinning in metal organic deposited YBCO films. Rare earth additions result in the formation of nanodots in the YBCO matrix, which form uncorrelated pinning centers, increasing pinning in all magnetic field orientations. 124-type intergrowths, which form as laminar structures parallel to the ab-plane, are responsible for the large current enhancement when the magnetic field is oriented in the ab-plane. TEM studies showed that the intergrowths emanate from cuprous containing secondary phase particles, whose density is partially controlled by the rare earth doping level. Critical process parameters have been identified to control this phase formation, and therefore, control the f 24 intergrowth formation. This work has shown that through process control and proper conductor design, either by adjusting the composition or by multiple coatings of different functional layers, the desired angular dependence can be achieved.

  16. Coexistence of Pinning and Moving on a Contact Line.

    Science.gov (United States)

    Lu, Zhengmao; Preston, Daniel J; Antao, Dion S; Zhu, Yangying; Wang, Evelyn N

    2017-09-12

    Textured surfaces are instrumental in water repellency or fluid wicking applications, where the pinning and depinning of the liquid-gas interface plays an important role. Previous work showed that a contact line can exhibit nonuniform behavior due to heterogeneities in surface chemistry or roughness. We demonstrate that such nonuniformities can be achieved even without varying the local energy barrier. Around a cylindrical pillar, an interface can reside in an intermediate state where segments of the contact line are pinned to the pillar top while the rest of the contact line moves along the sidewall. This partially pinned mode is due to the global nonaxisymmetric pattern of the surface features and exists for all textured surfaces, especially when superhydrophobic surfaces are about to be flooded or when capillary wicks are close to dryout.

  17. Impact of Edge-Barrier Pinning in Superconducting Thin Films

    Energy Technology Data Exchange (ETDEWEB)

    Jones, W. A.; Barnes, P.N.; Mullins, M. J.; Baca, F. J.; Emergo, R. L. S.; Wu, J.; Haugan, T. J.; Clem, J. R.

    2010-12-30

    It has been suggested that edge-barrier pinning might cause the critical current density (J{sub c}) in bridged superconducting films to increase. Subsequent work indicated that this edge-barrier effect does not impact bridges larger than 1 {micro}m. However, we provide a theoretical assessment with supporting experimental data suggesting edge-barrier pinning can significantly enhance J{sub c} for bridges of a few microns or even tens of microns thus skewing any comparisons among institutions. As such, when reporting flux pinning and superconductor processing improvements for J{sub c} comparisons, the width of the sample has to be taken into consideration as is currently done with film thickness.

  18. Self-pinning by colloids confined at a contact line

    Science.gov (United States)

    Weon, Byung; Je, Jung

    2013-03-01

    Colloidal particles suspended in a fluid usually inhibit complete wetting of the fluid on a solid surface and cause pinning of the contact line, known as self-pinning. We show differences in spreading and drying behaviors of pure and colloidal droplets using optical and confocal imaging methods. These differences come from spreading inhibition by colloids confined at a contact line. We propose a self-pinning mechanism based on spreading inhibition by colloids. We find a good agreement between the mechanism and the experimental result taken by directly tracking individual colloids near the contact lines of evaporating colloidal droplets. This research was supported by the Creative Research Initiatives (Functional X-ray Imaging) of MEST/NRF.

  19. The enhancement of vortex pinning in ferromagnet/superconductor bilayers

    Energy Technology Data Exchange (ETDEWEB)

    Cieplak, Marta Z.; Adamus, Z.; Abal' oshev, A.; Abal' osheva, I.; Berkowski, M. [Polish Academy of Sciences, Al. Lotnikw 32/46, 02668 Warsaw (Poland); Cheng, X.M.; Sang, Hai; Chien, C.L. [Department of Physics and Astronomy, The Johns Hopkins University, Baltimore, Md 21218 (United States)

    2005-03-01

    The magnetic-domain induced vortex pinning is studied in the ferromagnet/superconductor bilayers (FSB's), in which the F layers are Co/Pt multilayers with perpendicular magnetic anisotropy, and the S layers are either niobium or high temperature superconductor YBa{sub 2}Cu{sub 3}O{sub 7} (YBCO). The magnetization measurements reveal the enhancement of the flux pinning in both types of FSB's during the reversal of the magnetization of the F layer, but the details of the behavior depend on the type of the S layer. In the case of niobium FSB the maximum of pinning appears when the F layer is in the final stage of the magnetic reversal process, while the FSB with YBCO shows the maximum when the F layer is saturated. The possible origins of these differences are discussed. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  20. Motion of current filaments in avalanching PIN diodes

    Science.gov (United States)

    Xingrong, Ren; Changchun, Chai; Zhenyang, Ma; Yintang, Yang; Liping, Qiao; Chunlei, Shi; Lihua, Ren

    2013-04-01

    The motion of current filaments in avalanching PIN diodes has been investigated in this paper by 2D transient numerical simulations. The simulation results show that the filament can move along the length of the PIN diode back and forth when the self-heating effect is considered. The voltage waveform varies periodically due to the motion of the filament. The filament motion is driven by the temperature gradient in the filament due to the negative temperature dependence of the impact ionization rates. Contrary to the traditional understanding that current filamentation is a potential cause of thermal destruction, it is shown in this paper that the thermally-driven motion of current filaments leads to the homogenization of temperature in the diode and is expected to have a positive influence on the failure threshold of the PIN diode.

  1. Ordered Pinning Arrays with Tunable Geometry via Thermal Effects

    Science.gov (United States)

    Trastoy, Juan; Bernard, Rozenn; Briatico, Javier; Villegas, Javier E.; Malnou, Maxime; Bergeal, Nicolas; Lesueur, Jerome; Ulysse, Christian; Faini, Giancarlo

    2015-03-01

    We have used geometrically frustrated pinning arrays to create artificial vortex-ice. The pinning arrays are fabricated via ion irradiation of high-Tc superconducting films. These arrays present a very unique characteristic: the frustration can be reversibly switched on/off using temperature as a control knob, which allows stabilizing either a vortex-ice or a square vortex lattice. We have further investigated the thermal switching mechanism by studying the matching of the flux lattice to arrays that are incrementally deformed upon fabrication by introducing minute variations of the distance between pins. The array deformation exacerbates the thermal effects, leading to dramatic variations of the vortex distribution as a function of temperature. These results illustrate the strength of the temperature-induced reconfiguration effects, which may constitute a novel knob in fluxtronic devices based on vortex manipulation. Work supported by the French ANR MASTHER, the COST Action NanoSC, the Ville de Paris and the Galician Fundacion Barrie.

  2. Sessile droplet de-pinning: new life for gravimetric data.

    Science.gov (United States)

    Chan, Kwaichow B; Pierce, Scott M

    2007-02-01

    Using three different types of surfaces as exemplars, we report a gravimetric method as a viable tool for studying the de-pinning process. Namely, the de-pin time, tau(d) (the time required for a horizontal sessile droplet to de-pin at the triple phase line on a given substrate), is estimated without using a time consuming and expensive video imaging system. This is made possible by deciphering the non-linear portion of mass vs time data of an evaporating sessile droplet. Typical gravimetric glass-substrate evaporative mass loss vs time data has two regimes: a long, linear regime followed by a short, non-linear regime. Traditionally, researchers extract only the evaporation rate of a droplet from the linear regime but discard (by truncating the data) or ignore (thus deriving no information from) the non-linear regime. The origin of the linear to non-linear transition, found almost universally in gravimetric data, persists unremarked upon. By constructing three very different types of surfaces and comparing gravimetric data with video imaging data taken simultaneously, we report the transition is correlated to the onset of the de-pinning event in each case. This realization enables us to measure the de-pin time, tau(d), with gravimetric data only; i.e., without the video system, gathering more information from gravimetric data than previously considered. The method has application in estimating the de-pin time of a droplet deposited on a substrate that yields poor top-view contrast for videography, such as a water droplets on silicon wafers or glass substrates. Finally, gravimetric data is more accurate for evaporation modeling when substrate/droplet interaction areas are not circular.

  3. Method and apparatus for enhancing vortex pinning by conformal crystal arrays

    Science.gov (United States)

    Janko, Boldizsar; Reichhardt, Cynthia; Reichhardt, Charles; Ray, Dipanjan

    2015-07-14

    Disclosed is a method and apparatus for strongly enhancing vortex pinning by conformal crystal arrays. The conformal crystal array is constructed by a conformal transformation of a hexagonal lattice, producing a non-uniform structure with a gradient where the local six-fold coordination of the pinning sites is preserved, and with an arching effect. The conformal pinning arrays produce significantly enhanced vortex pinning over a much wider range of field than that found for other vortex pinning geometries with an equivalent number of vortex pinning sites, such as random, square, and triangular.

  4. Evaluation of stresses caused by dentin pin with finite elements stress analysis method.

    Science.gov (United States)

    Ersöz, E

    2000-09-01

    The aim of the present study was to show the dimensions and the amount of stresses caused by pins on dentin. Mathematically modelled stainless steel and titanium pins were applied to mandibular first molar teeth with extensive crown destruction. The stress caused by the pins was examined with the finite elements method (FEM). In both types of pin, the maximum diffuse and the dense stress areas were located at the bottom of the pin channel. It is believed that these stresses should be taken into consideration when evaluating the advantages and disadvantages of pin application to teeth with destroyed crowns.

  5. Medical Gas Cylinder with Mismatched Colour and Pin Index

    Directory of Open Access Journals (Sweden)

    Mukherjee S

    2014-08-01

    Full Text Available The medical gas cylinders have various safety features to prevent the administration of wrong gas to the patient. Most of the features have visual impact (colour, label, markings on the cylinder body except pin index system on the cylinder valve, so error in this feature is difficult to analyze and is highly unpredictable. We had received one such cylinder in our institution where all other features (label, colour, marking pointed to nitrous oxide except the pin index which resembled with that of oxygen

  6. Inner shell radial pin geometry and mounting arrangement

    Science.gov (United States)

    Leach, David; Bergendahl, Peter Allen

    2002-01-01

    Circumferentially spaced arrays of support pins are disposed through access openings in an outer turbine shell and have projections received in recesses in forward and aft sections of an inner turbine shell supported from the outer shell. The projections have arcuate sides in a circumferential direction affording line contacts with the side walls of the recesses and are spaced from end faces of the recesses, enabling radial and axial expansion and contraction of the inner shell relative to the outer shell. All loads are taken up in a tangential direction by the outer shell with the support pins taking no radial loadings.

  7. An open safety pin in the larynx: a case report.

    Science.gov (United States)

    Hussain, S S; Raine, C H; Caldicott, L D; Wade, M J

    1994-03-01

    Inhalation of a foreign body is a serious event. The number of foreign bodies that become impacted in the larynx is small and requires urgent recognition. We describe the case of a six-month-old baby with an impacted open safety pin in the larynx. The sharp end of the safety pin was upwards and had penetrated the anterior end of the left vocal fold. We discuss the management and describe our method of removal of the foreign body. Tracheostomy was not required in this case and the child had an uneventful recovery. A brief review of the literature is included.

  8. Swallowing a safety pin: Report of a case.

    Science.gov (United States)

    Benizri, Emmanuel Isaac; Cohen, Charlotte; Bereder, Jean Marc; Rahili, Amine; Benchimol, Daniel

    2012-01-27

    Ingestion of a foreign body is a frequent and well-known medical problem with several diagnostic and therapeutic approaches. Usually, ingested foreign bodies pass through the alimentary tract without incident. In some cases, they can be lodged in the appendix and may cause appendicitis. We report a case of a 29-year old woman, suffering from mental illness, with a safety pin lodged in the appendix. Initially, the patient consulted for abdominal pain. After a period of waiting, during which time the foreign body did not move, a colonoscopy was performed but failed to see the safety pin. Then, the patient underwent a laparoscopic appendectomy. Pathological examination showed an ulcerative appendicitis.

  9. Cost and effect of pinning control for network synchronization

    Institute of Scientific and Technical Information of China (English)

    Li Rong; Duan Zhi-Sheng; Chen Guan-Rong

    2009-01-01

    The problem of pinning control for the synchronization of complex dynamical networks is discussed in this paper. A cost function of the controlled network is defined by the feedback gain and the coupling strength of the network. An interesting result is that a lower cost is achieved by using the control scheme of pinning nodes with smaller degrees. Some strict mathematical analyses are presented for achieving a lower cost in the synchronization of different star-shaped various star-shaped networks are performed for verification and illustration.

  10. Establishment of the PIN within the Colombian party system

    Directory of Open Access Journals (Sweden)

    Vanessa Ortiz López

    2012-12-01

    Full Text Available This paper is a review of the legislative elections held in Colombia in 2010 and one of their main results, the establishment of the National Integration Party (PIN. The authors offer an analysis of articles that appeared in printed media, taking into consideration such variables as financing, legal constitution, popular acceptance and settling time. In this way, the authors attempt to demonstrate how the PIN managed to get a place in the political system and what are the consequences of this development, in particular, as the Department of Valle del Cauca is concerned.

  11. Force-State Characterization of Struts Using Pinned Joints

    Directory of Open Access Journals (Sweden)

    Brook D. Ferney

    1997-01-01

    Full Text Available As part of a research effort to study the microgravity dynamics of a truss with pinned joints, a single strut with a single clevis-tang pinned joint was characterized. Experimental data was collected using a force-state mapping technique. The strut was subjected to axial dynamic loads and the response of the strut was measured. The force-state map aids visualization of the strut dynamics. Finite element modeling of the response was explored. An example is presented that uses a method of manual determination of the finite element model parameters. The finite element model results correspond well with the measured strut response.

  12. Development and analysis of superconductors with projected nanostructured pinning centers

    Science.gov (United States)

    Rodrigues, Carlos A.; Rodrigues, D.

    2004-08-01

    The present work has the main objective to study the influence of the proximity effect on the superconducting properties of materials with pinning center dimensions comparable to the coherence length. Artificial Pinning Centers (APC) of Cu(Sn) were introduced into the Nb 3Sn superconducting phase using successive bundlings followed by swaging and wire drawing. Three superconductor wires were produced using the internal tin method. After fabrication, the samples were heat treated to optimize the superconducting phase formation. Microstructural and superconducting characterization of the samples were realized. The results showed the influence of the proximity effect on Tc, Jc and Bc2.

  13. Correlation between exchange bias and pinned interfacial spins.

    Science.gov (United States)

    Ohldag, H; Scholl, A; Nolting, F; Arenholz, E; Maat, S; Young, A T; Carey, M; Stöhr, J

    2003-07-04

    Using x-ray magnetic circular dichroism, we have detected the very interfacial spins that are responsible for the horizontal loop shift in three different exchange bias sandwiches, chosen because of their potential for device applications. The "pinned" uncompensated interfacial spins constitute only a fraction of a monolayer and do not rotate in an external magnetic field since they are tightly locked to the antiferromagnetic lattice. A simple extension of the Meiklejohn and Bean model is proposed to account quantitatively for the exchange bias fields in the three studied systems from the experimentally determined number of pinned moments and their sizes.

  14. Overexpression of PvPin1, a Bamboo Homolog of PIN1-Type Parvulin 1, Delays Flowering Time in Transgenic Arabidopsis and Rice

    Directory of Open Access Journals (Sweden)

    Zhigang Zheng

    2017-09-01

    Full Text Available Because of the long and unpredictable flowering period in bamboo, the molecular mechanism of bamboo flowering is unclear. Recent study showed that Arabidopsis PIN1-type parvulin 1 (Pin1At is an important floral activator and regulates floral transition by facilitating the cis/trans isomerization of the phosphorylated Ser/Thr residues preceding proline motifs in suppressor of overexpression of CO 1 (SOC1 and agamous-like 24 (AGL24. Whether bamboo has a Pin1 homolog and whether it works in bamboo flowering are still unknown. In this study, we cloned PvPin1, a homolog of Pin1At, from Phyllostachys violascens (Bambusoideae. Bioinformatics analysis showed that PvPin1 is closely related to Pin1-like proteins in monocots. PvPin1 was widely expressed in all tested bamboo tissues, with the highest expression in young leaf and lowest in floral bud. Moreover, PvPin1 expression was high in leaves before bamboo flowering then declined during flower development. Overexpression of PvPin1 significantly delayed flowering time by downregulating SOC1 and AGL24 expression in Arabidopsis under greenhouse conditions and conferred a significantly late flowering phenotype by upregulating OsMADS56 in rice under field conditions. PvPin1 showed subcellular localization in both the nucleus and cytolemma. The 1500-bp sequence of the PvPin1 promoter was cloned, and cis-acting element prediction showed that ABRE and TGACG-motif elements, which responded to abscisic acid (ABA and methyl jasmonate (MeJA, respectively, were characteristic of P. violascens in comparison with Arabidopsis. On promoter activity analysis, exogenous ABA and MeJA could significantly inhibit PvPin1 expression. These findings suggested that PvPin1 may be a repressor in flowering, and its delay of flowering time could be regulated by ABA and MeJA in bamboo.

  15. Electrical Conductivity of Cryolite Melts

    Science.gov (United States)

    Fellner, P.; Grjotheim, K.; Kvande, H.

    1985-11-01

    This paper proposes an equation for the electrical conductivity of multicomponent cryolite-based mixtures. The equation is based on a physical model which assumes that the conductivity is proportional to the number density of the effective electric charges in the melt. The various authors in the available literature show a great discrepancy in conductivity data of cryolite-based melts. The equation based on the physical model enables determination of which set of data is preferable. Special consideration in this respect is given to the influence of magnesium flouride and lithium flouride additions to the melt.

  16. Assessment of pin-by-pin fission rate distribution within MOX/UO{sub 2} fuel assembly using MCNPX code

    Energy Technology Data Exchange (ETDEWEB)

    Louis, Heba Kareem; Amin, Esmat [Nuclear and Radiological Regulation Authority (NRRA), Cairo (Egypt). Safety Engineering Dept.

    2016-03-15

    The aim of the present paper is to assess the calculations of pin-by-pin group integrated fission rates within MOX/UO{sub 2} Fuel assemblies using the Monte Carlo code MCNP2.7c with two sets of the available latest nuclear data libraries used for calculating MOX-fueled systems. The data that are used in this paper are based on the benchmark by the NEA Nuclear Science Committee (NSC). The k{sub ∞} and absorption/fission reaction rates per isotope, k{sub eff} and pin-by-pin group integrated fission rates on 1/8 fraction of the geometry are determined. To assess the overall pin-by-pin fission rate distribution, the collective per cent error measures were investigated. The results of AVG, MRE and RMS error measures were less than 1 % error. The present results are compared with other participants using other Monte Carlo codes and with CEA results that were taken in the benchmark as reference. The results with ENDF/B-VI.6 are close to the results received by MVP (JENDL3.2) and SCALE 4.2 (JEF2.2). The results with ENDF/BVII.1 give higher values of k{sub ∞} reflecting the changes in the newer evaluations. In almost all results presented here, the MCNP calculated results with ENDF/B VII.1 should be considered more than those obtained by using other Monte Carlo codes and nuclear data libraries. The present calculations may be consider a reference for evaluating the numerical schemes in production code systems, as well as the global performance including cross-section data reduction methods as the calculations used continuous energy and no geometrical approximations.

  17. Expertise concerning the request by the ZWILAG Intermediate Storage Wuerenlingen AG for delivery of the operation licence for the conditioning installation as well as for the burning and melting installation of the central intermediate storage facility for radioactive wastes in Wuerenlingen; Gutachten zum Gesuch der ZWILAG Zwischenlager Wuerenlingen AG um Erteilung der Betriebsbewilligung fuer die Konditionierungsanlage sowie fuer die Verbrennungs- und Schmelzanlage des Zentralen Zwischenlagers fuer radioaktive Abfaelle in Wuerenlingen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-08-15

    On December 15, 1997, the Central Intermediate Storage Facility for radioactive materials (ZWILAG) delivered a request to the Swiss Federal Council for an operational licence for the conditioning installation and the incineration and melting installation at the Central Intermediate Storage Facility (ZZL). For the whole project, the general licence was granted on June 23, 1993. The construction of the whole installation as well as the operation in the storage halls with reception, hot cell and transhipment station were licensed on August 12, 1999. The Federal Agency for the Safety of Nuclear Installations (HSK) examined the request documentation of ZWILAG from the point of view of nuclear safety and radiation protection. The results of the examination are contained in this report. In general, the examination leads to a positive decision. During the realisation process many project adaptations have brought improvements to the installation as far as radiation protection and the treatment of wastes are concerned. HSK requests from a former licensing process were taken into account by ZWILAG. The present examination contains many remarks and requests that the HSK considers necessary. The most important remarks are issued as special references as far as they do not appear as proposals in the licence obligations. In general, the reference form was chosen when the fulfilment of the request can be guarantied by HSK within the framework of a release process. Several references inform ZWILAG of problems for which HSK wishes to receive the results of extended inquiries or where HSK will assist in testing or demonstrations. Other references concern requests for plant documentation. Further, calculations of radioactive material release during normal operation is considered as being necessary. Based on its examination, HSK concludes that the conditions are fulfilled for the safe operation of the conditioning installation and of the incineration and melting installation as long as

  18. Nitrogen Control in VIM Melts

    Science.gov (United States)

    Jablonski, P. D.; Hawk, J. A.

    NETL has developed a design and control philosophy for the addition of nitrogen to austenitic and ferritic steels. The design approach uses CALPHAD as the centerpiece to predict the level to which nitrogen is soluble in both the melt and the solid. Applications of this technique have revealed regions of "exclusion" in which the alloy, while within specification limits of prescribed, cannot be made by conventional melt processing. Furthermore, other investigations have found that substantial retrograde solubility of nitrogen exists, which can become problematic during subsequent melt processing and/or other finishing operations such as welding. Additionally, the CALPHAD method has been used to adjust primary melt conditions. To that end, nitrogen additions have been made using chrome nitride, silicon nitride, high-nitrogen ferrochrome as well as nitrogen gas. The advantages and disadvantages of each approach will be discussed and NETL experience in this area will be summarized with respect to steel structure.

  19. The influence of the repetition rate on the nanosecond pulsed pin-to-pin microdischarges

    Science.gov (United States)

    Huang, Bang-Dou; Takashima, Keisuke; Zhu, Xi-Ming; Pu, Yi-Kang

    2014-10-01

    The effect of repetition rate on a nanosecond atmospheric pressure discharge is investigated. The discharge is generated between two pins in a mixture of Ne and Ar. The voltage, current, power waveforms and the temporally and spatially resolved electron density and an ‘effective’ electron temperature are measured, with a pulse interval between 1.5 and 200 µs. It is found that not only does the repetition rate have a strong influence on the breakdown voltage and the peak discharge power, but it can also affect the rise rate of the volume averaged electron density and its peak value. Temporally and spatially resolved measurement of the electron density and the effective electron temperature show that the spatial distributions of both quantities are also influenced by the repetition rate. In the initial discharge period of all cases, the sharp rise of the electron density correlates with the drastic drop of the effective electron temperature. It is suggested that the residual charges have a strong impact on the axial distribution of the electric field and energetic electrons between the electrodes during the breakdown period, as illustrated by a simple sheath model.

  20. Evaluation of PWR and BWR pin cell benchmark results

    Energy Technology Data Exchange (ETDEWEB)

    Pijlgroms, B.J.; Gruppelaar, H.; Janssen, A.J. (Netherlands Energy Research Foundation (ECN), Petten (Netherlands)); Hoogenboom, J.E.; Leege, P.F.A. de (Interuniversitair Reactor Inst., Delft (Netherlands)); Voet, J. van der (Gemeenschappelijke Kernenergiecentrale Nederland NV, Dodewaard (Netherlands)); Verhagen, F.C.M. (Keuring van Electrotechnische Materialen NV, Arnhem (Netherlands))

    1991-12-01

    Benchmark results of the Dutch PINK working group on PWR and BWR pin cell calculational benchmark as defined by EPRI are presented and evaluated. The observed discrepancies are problem dependent: a part of the results is satisfactory, some other results require further analysis. A brief overview is given of the different code packages used in this analysis. (author). 14 refs., 9 figs., 30 tabs.

  1. BetterThanPin: Empowering Users to Fight Phishing (Poster)

    Science.gov (United States)

    Tan, Teik Guan

    The BetterThanPin concept is an online security service that allows users to enable almost any Cloud or Web-based account (e.g. Gmail, MSN, Yahoo, etc) to be protected with "almost" 2-factor authentication (2FA). The result is that users can now protect their online accounts with better authentication, without waiting for the service or cloud provider.

  2. Ultrasonic decontamination of prototype fast breeder reactor fuel pins.

    Science.gov (United States)

    Kumar, Aniruddha; Bhatt, R B; Behere, P G; Afzal, Mohd

    2014-04-01

    Fuel pin decontamination is the process of removing particulates of radioactive material from its exterior surface. It is an important process step in nuclear fuel fabrication. It assumes more significance with plutonium bearing fuel known to be highly radio-toxic owing to its relatively longer biological half life and shorter radiological half life. Release of even minute quantity of plutonium oxide powder in the atmosphere during its handling can cause alarming air borne activity and may pose a severe health hazard to personnel working in the vicinity. Decontamination of fuel pins post pellet loading operation is thus mandatory before they are removed from the glove box for further processing and assembly. This paper describes the setting up of ultrasonic decontamination process, installed inside a custom built fume-hood in the production line, comprising of a cleaning tank with transducers, heaters, pin handling device and water filtration system and its application in cleaning of fuel pins for prototype fast breeder reactor. The cleaning process yielded a typical decontamination efficiency of more than 99%.

  3. Safety pin - The UNSAFE foreign body of air passage.

    Science.gov (United States)

    Dasgupta, K S; Lanjewar, K Y; Joshi, S V

    2006-10-01

    Foreign bodies in the air passage are familiar otolaryngological emergencies. The diagnosis and management in most cases is based on clinico-radiological findings. Here, we are reporting three cases of open safety pin at various locations in the respiratory tract i.e. in the nose, nasopharynx and larynx. Their clinical presentation and management are described in detail.

  4. Pinning an Ion with an Intracavity Optical Lattice

    DEFF Research Database (Denmark)

    Linnet, Rasmus Bogh; Leroux, Ian Daniel; Marciante, Mathieu

    2012-01-01

    We report one-dimensional pinning of a single ion by an optical lattice. A standing-wave cavity produces the lattice potential along the rf-field-free axis of a linear Paul trap. The ion’s localization is detected by measuring its fluorescence when excited by standing-wave fields with the same...

  5. Spectrometry and dosimetry of fast neutrons using pin diode detectors

    Energy Technology Data Exchange (ETDEWEB)

    Zaki Dizaji, H., E-mail: hz.dizaji@znu.ac.ir [Physics Department, Faculty of Science, Zanjan University, Zanjan (Iran, Islamic Republic of); Kakavand, T. [Physics Department, Faculty of Science, International Imam Khomeini University, Qazvin (Iran, Islamic Republic of); Abbasi Davani, F. [Radiation Application Department, Shahid Beheshti University, Tehran (Iran, Islamic Republic of)

    2014-03-21

    Elastic scattering of light nuclei, especially hydrogen, is widely used for detection of fast neutrons. Semiconductor devices based on silicon detectors are frequently used for different radiation detections. In this work, a neutron spectrometer consisting of a pin diode coupled with a polyethylene converter and aluminum degrader layers has been developed. Aluminum layers are used as discriminators of different neutron energies for detectors. The response of the converter–degrader–pin diode configuration, the optimum thickness of the converter and the degrader layers have been extracted using MCNP and SRIM simulation codes. The possibility of using this type of detector for fast neutron spectrometry and dosimetry has been investigated. A fairly good agreement was seen between neutron energy spectrum and dose obtained from our configurations and these specifications from an {sup 241}Am–Be neutron source. - Highlights: • Silicon pin diodes are applied to the fast neutron detection. • The technique of converter degrader pin diode is used for spectrometry of fast neutrons. • The method is used for dosimetry of fast neutron.

  6. Pinning synchronization of networked multi-agent systems:spectral analysis

    Institute of Scientific and Technical Information of China (English)

    Linying XIANG; Fei CHEN; Guanrong CHEN

    2015-01-01

    Pinning synchronization of a networked multi-agent system with a directed communication topology is investigated from a spectral analysis approach. Some new types of synchronized regions for networked systems with different nonlinear agent dynamics and inner coupling structures are discovered. The eigenvalue distributions of the coupling and control matrices for different types of directed networks are obtained. The effects of the network topology, pinning density and pinning strength on the network synchronizability are examined through extensive numerical simulations. It is shown that the synchronizability of the pinned network can be effectively improved by increasing pinning density and pinning strength for some types of synchronized regions, whereas too large the pinning density and pinning strength will lead to desynchronization for other types. It is found that directed random networks are not always easier to synchronize than directed small-world networks, and a denser eigenvalue distribution may not always imply better synchronizability.

  7. Experimental study on thermal performance of micro pin fin heat sinks with various shapes

    Science.gov (United States)

    Hua, Junye; Li, Gui; Zhao, Xiaobao; Li, Qihe

    2017-03-01

    This paper presents a visualization experimental study on the heat transfer characteristics of various shapes of micro pin fins, including the circular, ellipse, diamond, square and triangle shape micro pin fin arrays with various equivalent diameters and pin fin density. The influences study of different sizes and shapes of pin fin on Nusselt number and heat transfer coefficient have been conducted. The results show that with the increase of the flow rate, the temperature of the bottom of the experimental section decreases. And the Nusselt number of different shapes of micro pin fins increases with the increase of Re. In which, the heat transfer performance of the ellipse shape pin fin appears better among the other shapes of pin fins. However, the higher pin fin of the ellipse shape density leads to a weaker flow performance. Besides, the micro-scale heat transfer correlation between the Nusselt number and the Reynolds number is fitted based on the experimental data.

  8. Increased expression of PIN1 gene in papillary thyroid carcinoma

    Directory of Open Access Journals (Sweden)

    Lewiński Andrzej

    2011-01-01

    Full Text Available Abstract Background Peptidyl-prolyl cis/trans isomerase (Pin1, encoded by PIN1 gene with locus in chromosome 19p13, is an enzyme that catalytically induces conformational changes in proteins after phosphorylation on serine or threonine residues preceding proline (pSer/Thr-Pro motifs; in this way, it has an influence on protein interactions and intracellular localizations of proteins. The aim of the study were: 1 an assessment of PIN1 gene expression level in benign and malignant thyroid lesions; 2 the evaluation of possible correlations between gene expression and histopathological variants of papillary thyroid carcinoma (PTC or tumour size, classified according to TNM classification of primary tumours (in case of PTC only; 3 the estimation of possible relationships between expression of the gene in question and patients' sex or age. Methods Seventy (70 tissue samples were analyzed: 32 cases of PTC, 7 cases of medullary thyroid carcinoma (MTC, 7 cases of follicular adenoma (FA, and 24 cases of nodular goitre (NG. In real-time polymerase chain reaction (real-time PCR, two-step RT-PCR (reverse transcriptase-polymerase chain reaction in an ABI PRISM 7500 Sequence Detection System was employed. The PIN1 gene expression level was assessed, calculating the mean relative quantification rate (RQ rate increase for each sample. Results The level of PIN1 gene expression (compared to that in macroscopically unchanged thyroid tissue was higher in PTC group than those in FA, MTC and/or NG groups, but the statistical significance was noted for difference between PTC and NG groups only. On the other hand, the differences of RQ rate value between different PTC variants were statistically insignificant. No correlations were found between RQ values and tumour size, as well as between RQ values and patients' sex or age in PTC group. Conclusions The PIN1 gene expression may have - in future - an important meaning in the diagnostics of PTC and in understanding its

  9. Laser melting of uranium carbides

    Science.gov (United States)

    Utton, C. A.; De Bruycker, F.; Boboridis, K.; Jardin, R.; Noel, H.; Guéneau, C.; Manara, D.

    2009-03-01

    In the context of the material research aimed at supporting the development of nuclear plants of the fourth Generation, renewed interest has recently arisen in carbide fuels. A profound understanding of the behaviour of nuclear materials in extreme conditions is of prime importance for the analysis of the operation limits of nuclear fuels, and prediction of possible nuclear reactor accidents. In this context, the main goal of the present paper is to demonstrate the feasibility of laser induced melting experiments on stoichiometric uranium carbides; UC, UC1.5 and UC2. Measurements were performed, at temperatures around 3000 K, under a few bars of inert gas in order to minimise vaporisation and oxidation effects, which may occur at these temperatures. Moreover, a recently developed investigation method has been employed, based on in situ analysis of the sample surface reflectivity evolution during melting. Current results, 2781 K for the melting point of UC, 2665 K for the solidus and 2681 K for the liquidus of U2C3, 2754 K for the solidus and 2770 K for the liquidus of UC2, are in fair agreement with early publications where the melting behaviour of uranium carbides was investigated by traditional furnace melting methods. Further information has been obtained in the current research about the non-congruent (solidus-liquidus) melting of certain carbides, which suggest that a solidus-liquidus scheme is followed by higher ratio carbides, possibly even for UC2.

  10. Scaleable Clean Aluminum Melting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Han, Q.; Das, S.K. (Secat, Inc.)

    2008-02-15

    The project entitled 'Scaleable Clean Aluminum Melting Systems' was a Cooperative Research and Development Agreements (CRADAs) between Oak Ridge National Laboratory (ORNL) and Secat Inc. The three-year project was initially funded for the first year and was then canceled due to funding cuts at the DOE headquarters. The limited funds allowed the research team to visit industrial sites and investigate the status of using immersion heaters for aluminum melting applications. Primary concepts were proposed on the design of furnaces using immersion heaters for melting. The proposed project can continue if the funding agency resumes the funds to this research. The objective of this project was to develop and demonstrate integrated, retrofitable technologies for clean melting systems for aluminum in both the Metal Casting and integrated aluminum processing industries. The scope focused on immersion heating coupled with metal circulation systems that provide significant opportunity for energy savings as well as reduction of melt loss in the form of dross. The project aimed at the development and integration of technologies that would enable significant reduction in the energy consumption and environmental impacts of melting aluminum through substitution of immersion heating for the conventional radiant burner methods used in reverberatory furnaces. Specifically, the program would couple heater improvements with furnace modeling that would enable cost-effective retrofits to a range of existing furnace sizes, reducing the economic barrier to application.

  11. Routine radiographs at time of pin removal after closed reduction and percutaneous pinning for type 2 supracondylar humerus fractures do not change management: a retrospective cohort study.

    Science.gov (United States)

    Garg, Sumeet; Bloch, Nikki; Cyr, Micaela; Carry, Patrick

    2016-08-01

    Radiographs are usually taken on day of pin removal for children treated with closed reduction and percutaneous pinning (CRPP) of type 2 supracondylar humerus fractures. The purpose of this study was to determine whether radiographs taken at time of pin removal for patients recovering uneventfully alter management. After IRB approval, billing records identified 1213 patients aged 1-10 years who underwent elbow surgery between 2007 and 2013 at our institution for a supracondylar humerus fracture. Of these patients, 389 met inclusion criteria. Clinical charts were reviewed for demographics, operative details, and clinical follow-up, focusing on clinical symptoms present at pin removal. Radiographs taken at time of pin removal and subsequent visits were assessed for healing and fracture alignment. In no case was pin removal delayed based on radiographs. One hundred and nineteen (31 %) patients had radiographs taken following pin removal; in no case was loss of reduction found among these patients. No cases of neurologic or vascular injury, re-fracture, or loss of reduction occurred. Infection occurred in 12 patients (3 %). Pins were kept in place for 23.8 ± 4.4 days. Eighty-six patients (22 %) had additional intervention after pin removal (cast application in all cases). Of 389 patients, 75 (19 %) had no documented reason for extended casting, four (1 %) were extended based on physician evaluation of radiographs, and seven (2 %) were extended for other reasons. Elimination of radiographs at time of pin removal should be considered. If continuing to obtain radiographs at pin removal, we recommend removing pins before taking radiographs to reduce patient fear and anxiety from visualizing percutaneous pins.

  12. EXPERIMENTAL ANALYSIS OF FLEXURAL STRENGTH ON GLASS FIBER SANDWICH COMPOSITE BY VARYING Z-PINS PITCHES

    OpenAIRE

    Pravin*, Jeyapratha

    2016-01-01

    This paper ambit to evaluate the flexural strength of glass fiber sandwich panels with varying z-pins pitches. Failure of sandwich panel are delamination and core shear, to minimize the crack propagation, pins are inserted in z-direction, by varying pitches through its thickness. During the insertion of pin, may cause the material some damage. Despite the damage, flexural property does not affected due interpolation of pins. Although the experiment were pull out with a phenomenal results of z...

  13. Effects of ZrB{sub 2} on substructure and wear properties of laser melted in situ ZrB{sub 2p}/6061Al composites

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Yida [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Chao, Yuhjin [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); Department of Mechanical Engineering, University of South Carolina, Columbia, SC 29208 (United States); Luo, Zhen, E-mail: lz@tju.edu.cn [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Cai, Yangchuan [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Huang, Yongxian [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China)

    2016-03-01

    Graphical abstract: - Highlights: • Laser beam partly disperses ZrB{sub 2} particle clusters and showing dispersed particles state after matrix solidification. • Laser melting process narrower cellular spacing in composites than AA6061 matrix. • Compared with matrix alloy, crystal orientation near melted layer edge of the composites is almost random duo to heterogeneous nucleation in melt and pinning effect of laser dispersed ZrB{sub 2} nanoparticles at solidification front. • Laser melted layer shows better wear properties than matrix and composite without laser melting. - Abstract: Aluminum matrix composites reinforced by in situ ZrB{sub 2} particles were successfully fabricated from an Al-KBF{sub 4}-K{sub 2}ZrF{sub 6} system via a direct melt reaction. A laser surface melting strategy is used to improve the surface strength of the in situ ZrB{sub 2p}/6061Al composite, which includes a series of laser-melted composites with different laser power processed by a 2 kW YAG laser generator. XRD and EDS results demonstrated the existence of ZrB{sub 2} nanoparticles in the composite. After laser melting, the penetration depth of the molten pool increases with increasing power density. OM and SEM analysis indicate that the laser melting process yields narrower cellular spacing of the matrix and partly disperses the ZrB{sub 2} particle clusters. Compared with laser-melted matrix alloys, the crystal orientations near the melted layers edge of the composite are almost random due to heterogeneous nucleation in the melt and the pinning effect of laser-dispersed ZrB{sub 2} nanoparticles at the solidification front. Wear test results show that the laser melted layer performs better at wear resistance than both the substrate and the matrix AA6061 by measuring wear mass loss. Compared with composite samples prepared without laser melting, the wear mass loss of the laser melted composites decreased from 61 to 56 mg under a load of 98 N for 60 min.

  14. Laser melting of plasma nitrided Ti-6Al-4V alloy

    Energy Technology Data Exchange (ETDEWEB)

    Yilbas, B.S.; Sami, M.; Shuja, S.Z.; Aleem, A. [KFUPM, Dhahran (Saudi Arabia). Mechanical Engineering Dept.; Nickel, J.; Coban, A. [Energy Research Lab., Research Inst., KFUPM, Dhahran (Saudi Arabia)

    1997-11-30

    A laser surface modification technique can be used as a part of a dublex treatment process to improve the surface properties of Ti-6Al-4V alloy. The present study is conducted to investigate the surface properties of the Ti-6Al-4V alloy due to laser melting prior to a plasma nitriding process. Consequently, nitriding is carried out to obtain the depth of the nitride zone of 30 {mu}m. A CO{sub 2} laser with 1.6 kW output power was used to melt the nitride layers. The wear properties of the plasma nitrided and nitrided/melted surfaces were investigated using pin-on-disc equipment while the friction coefficient was determined using a ball-on-disc machine. The nitride depth profile was measured using a nuclear analyses reaction and elemental distribution in the melted zones was investigated using {mu}-PIXE. Scanning electron microscopy and optical microscopy were carried out to analyze the microstructures developed before and after the laser melting process. In addition, heating and cooling rates were predicted through the electron-kinetic theory approach. (orig.)

  15. New Universal Tribometer as Pin or Ball-on-Disc and Reciprocating Pin-on-Plate Types

    Directory of Open Access Journals (Sweden)

    H. Kaleli

    2016-06-01

    Full Text Available The present paper contains a description of a new Universal Tribometer design which enables simulation of different contact and test types such as pin-on-disc, ball-on-disc and linear reciprocating tests. There are many models of wear Tribometer in the world market. These devices are manufactured by various companies abroad and are imported to our country. Cost of this devices start from 50.000 euros and goes to hundreds of thousands of euros. One of the most commonly used of this device is Reciprocating Pin-on-Plate Tribo Test Machine. This wear tester is produced at a low limited cost within the KAP (Scientifical Research Project Coordinator of Yıldız Technical University. The test machine can work including three types of Tribotest rigs (Reciprocating Pin-on-Plate, Pin-on-Disc and Ball-on-Disc. It is designed to operate also at high temperatures up to 500 ˚C. The new piece of equipment allows instrumented tribological testing of piston ring and cylinder liner samples at low and high temperatures and boundary lubrication conditions of any typical gasoline or Diesel engines. Some friction results were shown in boundary lubricating conditions between piston ring and cylinder liner sliding pairs describing Tribotest machine is driven by AC servo motor which is more accurate than DC motor.

  16. Quantifying melting and mobilistaion of interstitial melts in crystal mushes

    Science.gov (United States)

    Veksler, Ilya; Dobson, Katherine; Hess, Kai-Uwe; Ertel-Ingrisch, Werner; Humphreys, Madeleine

    2015-04-01

    The deformation of crystals mushes and separation of melts and crystals in is critical to understanding the development of physical and chemical heterogeneity in magma chambers and has been invoked as an eruption trigger mechanism. Here we investigate the behaviour of the melt in the well characterised, classic crystal mush system of the Skaergaard intrusion by combining experimental petrology and the non-destructive 3D imaging methods. Starting materials for partial melting experiments were four samples from the upper Middle Zone of the Layered Series. Cylinders, 15 mm in diameter and 20 mm in length, were drilled out of the rock samples, placed in alumina crucibles and held for 5 days in electric furnaces at atmospheric pressure and 1050-1100 °C. Redox conditions set by the CO-CO2 gas mixture were kept close to those of the FMQ buffer. We then use spatially registered 3D x-ray computed tomography images, collected before and after the experiment, to determine the volume and distribution of the crystal framework and interstitial phases, and the volume, distribution and connectivity the interstitial phases that undergo melting and extraction while at elevated temperature. Image analysis has allowed us to quantify these physical changes with high spatial resolution. Our work is a first step towards quantitative understanding of the melt mobilisation and migration processes operating in notionally locked crystal rich magmatic systems.

  17. Radiocarbon dating of the bronze age bone pins from Eurasian steppe

    NARCIS (Netherlands)

    Shishlina, Natalia I.; Van der Plicht, Johan; Zazovskaya, Elya P.

    2011-01-01

    Bone catapult and hammer-headed pins played one of very specific roles in funerary offerings in the Bronze Age graves uncovered in the Eurasian Steppes and the North Caucasus. Scholars used different types of pins as key grave offerings for numerous chronological models. For the first time eight pin

  18. Strain tunable light emitting diodes with germanium P-I-N heterojunctions

    Science.gov (United States)

    Lagally, Max G; Sanchez Perez, Jose Roberto

    2016-10-18

    Tunable p-i-n diodes comprising Ge heterojunction structures are provided. Also provided are methods for making and using the tunable p-i-n diodes. Tunability is provided by adjusting the tensile strain in the p-i-n heterojunction structure, which enables the diodes to emit radiation over a range of wavelengths.

  19. The PIN family of proteins in potato and their putative role in tuberisation

    NARCIS (Netherlands)

    Roumeliotis, E.; Kloosterman, B.A.; Oortwijn, M.E.P.; Visser, R.G.F.; Bachem, C.W.B.

    2013-01-01

    The PIN family of trans-membrane proteins mediates auxin efflux throughout the plant and during various phases of plant development. In Arabidopsis thaliana, the PIN family comprised of 8 members, divided into ‘short’ and ‘long’ PINs according to the length of the hydrophilic domain of the protein.

  20. PIN protein phosphorylation by plant AGC3 kinases and its role in polar auxin transport

    NARCIS (Netherlands)

    Huang, Fang

    2010-01-01

    Polar cell-to-cell transport of plant hormone auxin mediated by plasma membrane (PM)-localized PIN-FORMED (PIN) auxin efflux carriers generates auxin gradients that provide positional information for various plant developmental processes. The apical-basal polar localization of the PIN proteins that

  1. The PIN family of proteins in potato and their putative role in tuberisation

    Directory of Open Access Journals (Sweden)

    Efstathios eRoumeliotis

    2013-12-01

    Full Text Available The PIN family of trans-membrane proteins mediates auxin efflux throughout the plant and during various phases of plant development. In Arabidopsis thaliana, the PIN family comprised of 8 members, divided into ‘short’ and ‘long’ PINs according to the length of the hydrophilic domain of the protein. Based on sequence homology using the recently published potato genome sequence (Solanum tuberosum group Phureja we identified ten annotated potato StPIN genes. Mining the publicly available gene expression data, we constructed a catalogue tissue specificity of StPIN gene expression, focusing on the process of tuberization. A total of four StPIN genes exhibited increased expression four days after tuber induction, prior to the onset of stolon swelling. For two PIN genes, StPIN4 and StPIN2, promoter sequences were cloned and fused to the GUS reporter protein to study tissue specificity in more detail. StPIN4 promoter driven GUS staining was detected in the flower stigma, in the flower style, below the ovary and petals, in the root tips, in the vascular tissue of the stolons and in the tuber parenchyma cells. StPIN2 promoter driven GUS staining was detected in flower buds, in the vascular tissue of the swelling stolons and in the storage parenchyma of the growing tubers. Based on our results, we postulate a role for the StPINs in redistributing auxin in the swelling stolon during early events in tuber development.

  2. Melt-processed bulk superconductors: Fabrication and characterization for power and space applications

    Science.gov (United States)

    Hojaji, Hamid; Barkatt, Aaron; Hu, Shouxiang; Thorpe, Arthur N.; Ware, Matthew F.; Davis, David; Alterescu, Sidney

    1991-01-01

    Melt-process bulk superconducting materials based on variations on the base YBa2Cu3O(x) were produced in a variety of shapes and forms. Very high values of both zero-field and high-field magnetization were observed. These are useful for levitation and power applications. Magnetic measurements show that the effects of field direction and intensity, temperature and time are consistent with an aligned grain structure with multiple pinning sites and with models of thermally activated flux motion.

  3. Flux-flow fingerprint of disorder: Melting versus tearing of a flux-line lattice

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharya, S.; Higgins, M.J. [NEC Research Institute, 4 Independence Way, Princeton, New Jersey 08540 (United States)

    1995-07-01

    A steady-state inhomogeneous flow of a slowly moving flux-line lattice shows the fingerprint of the specific realization of dynamically generated disorder obtained through the interaction between the lattice and the quenched pinning centers. This is characteristic of ``tearing`` of a soft lattice and is pronounced in a narrow regime of the ({ital H},{ital T}) phase diagram where the system is neither a stiff lattice nor a fluid. A first-order depinning transition accompanying this nonequilibrium dynamical phenomenon is fundamentally different from an equilibrium ``melting`` of a flux-line lattice. A length scale is proposed to describe the dynamics.

  4. Methods for Melting Temperature Calculation

    Science.gov (United States)

    Hong, Qi-Jun

    Melting temperature calculation has important applications in the theoretical study of phase diagrams and computational materials screenings. In this thesis, we present two new methods, i.e., the improved Widom's particle insertion method and the small-cell coexistence method, which we developed in order to capture melting temperatures both accurately and quickly. We propose a scheme that drastically improves the efficiency of Widom's particle insertion method by efficiently sampling cavities while calculating the integrals providing the chemical potentials of a physical system. This idea enables us to calculate chemical potentials of liquids directly from first-principles without the help of any reference system, which is necessary in the commonly used thermodynamic integration method. As an example, we apply our scheme, combined with the density functional formalism, to the calculation of the chemical potential of liquid copper. The calculated chemical potential is further used to locate the melting temperature. The calculated results closely agree with experiments. We propose the small-cell coexistence method based on the statistical analysis of small-size coexistence MD simulations. It eliminates the risk of a metastable superheated solid in the fast-heating method, while also significantly reducing the computer cost relative to the traditional large-scale coexistence method. Using empirical potentials, we validate the method and systematically study the finite-size effect on the calculated melting points. The method converges to the exact result in the limit of a large system size. An accuracy within 100 K in melting temperature is usually achieved when the simulation contains more than 100 atoms. DFT examples of Tantalum, high-pressure Sodium, and ionic material NaCl are shown to demonstrate the accuracy and flexibility of the method in its practical applications. The method serves as a promising approach for large-scale automated material screening in which

  5. The prolyl isomerase Pin1 increases β-cell proliferation and enhances insulin secretion.

    Science.gov (United States)

    Nakatsu, Yusuke; Mori, Keiichi; Matsunaga, Yasuka; Yamamotoya, Takeshi; Ueda, Koji; Inoue, Yuki; Mitsuzaki-Miyoshi, Keiko; Sakoda, Hideyuki; Fujishiro, Midori; Yamaguchi, Suguru; Kushiyama, Akifumi; Ono, Hiraku; Ishihara, Hisamitsu; Asano, Tomoichiro

    2017-07-14

    The prolyl isomerase Pin1 binds to the phosphorylated Ser/Thr-Pro motif of target proteins and enhances their cis-trans conversion. This report is the first to show that Pin1 expression in pancreatic β cells is markedly elevated by high-fat diet feeding and in ob/ob mice. To elucidate the role of Pin1 in pancreatic β cells, we generated β-cell-specific Pin1 KO (βPin1 KO) mice. These mutant mice showed exacerbation of glucose intolerance but had normal insulin sensitivity. We identified two independent factors underlying impaired insulin secretion in the βPin1 KO mice. Pin1 enhanced pancreatic β-cell proliferation, as indicated by a reduced β-cell mass in βPin1 KO mice compared with control mice. Moreover, a diet high in fat and sucrose failed to increase pancreatic β-cell growth in the βPin1 KO mice, an observation to which up-regulation of the cell cycle protein cyclin D appeared to contribute. The other role of Pin1 was to activate the insulin-secretory step: Pin1 KO β cells showed impairments in glucose- and KCl-induced elevation of the intracellular Ca(2+) concentration and insulin secretion. We also identified salt-inducible kinase 2 (SIK2) as a Pin1-binding protein that affected the regulation of Ca(2+) influx and found Pin1 to enhance SIK2 kinase activity, resulting in a decrease in p35 protein, a negative regulator of Ca(2+) influx. Taken together, our observations demonstrate critical roles of Pin1 in pancreatic β cells and that Pin1 both promotes β-cell proliferation and activates insulin secretion. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

  6. Melting of superheated molecular crystals

    Science.gov (United States)

    Cubeta, Ulyana; Bhattacharya, Deepanjan; Sadtchenko, Vlad

    2017-07-01

    Melting dynamics of micrometer scale, polycrystalline samples of isobutane, dimethyl ether, methyl benzene, and 2-propanol were investigated by fast scanning calorimetry. When films are superheated with rates in excess of 105 K s-1, the melting process follows zero-order, Arrhenius-like kinetics until approximately half of the sample has transformed. Such kinetics strongly imply that melting progresses into the bulk via a rapidly moving solid-liquid interface that is likely to originate at the sample's surface. Remarkably, the apparent activation energies for the phase transformation are large; all exceed the enthalpy of vaporization of each compound and some exceed it by an order of magnitude. In fact, we find that the crystalline melting kinetics are comparable to the kinetics of dielectric α-relaxation in deeply supercooled liquids. Based on these observations, we conclude that the rate of non-isothermal melting for superheated, low-molecular-weight crystals is limited by constituent diffusion into an abnormally dense, glass-like, non-crystalline phase.

  7. Radiation Characteristics of Rectangular Patch Antennas with an Array of Pins

    Institute of Scientific and Technical Information of China (English)

    Myung-ki CHO; Tae-young KIM; Boo-gyoun KIM

    2010-01-01

    The patch antennas with an array of pins (pin array patch antennas) with excellent radiation characteristics are investigated for various substrate thicknesses.The radiation in the horizontal plane of a pin array patch antenna is very small campared to that of a conventional patch antenna.And the increase of forward radiation and the decrease of backward radiation of a pin array patch antenna are tained than these conventional one's.Also the half-power beamwidth of E-plane radiation pattern of a pin array patch antenna is narrower compared to that of the conventional so that the directivity is improved.

  8. Mammography Facilities

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Mammography Facility Database is updated periodically based on information received from the four FDA-approved accreditation bodies: the American College of...

  9. Health Facilities

    Science.gov (United States)

    Health facilities are places that provide health care. They include hospitals, clinics, outpatient care centers, and specialized care centers, such as birthing centers and psychiatric care centers. When you ...

  10. Canyon Facilities

    Data.gov (United States)

    Federal Laboratory Consortium — B Plant, T Plant, U Plant, PUREX, and REDOX (see their links) are the five facilities at Hanford where the original objective was plutonium removal from the uranium...

  11. A Pin gene families encoding components of auxin efflux carriers in Brassica juncea

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Based on the sequence information of Arabidopsis PIN1, two cDNAs encoding PIN homologues fromBrassica juncea, Bjpin2 and Bjpin3, were isolated through cDNA library screening. Bjpin2 and Bjpin3encoded proteins containing 640 and 635 amino acid residues, respectively, which shared 97.5% identities witheach other and were highly homologous to Arabidopsis PIN1, PIN2 and other putative PIN proteins. BjPIN2and BjPIN3 had similar structures as AtPIN proteins. Northern blot analysis indicated that Bjpin2 wasexpressed in stem, leaf and floral tissues, while Bjpin3 was expressed predominantly in stem and hypocotyls.Two promoter fragments of pin genes, Bjpin-X and Bjpin-Z, were isolated by 'genome walking' techniqueusing primers at 5'-end of pin cDNA. Promoter-gus fusion studies revealed the GUS activities driven byBjpin-X were at internal side of xylem and petal; while those driven by Bjpin-Z were detected at leaf vein,epidermal cell and cortex of stem, vascular tissues and anther. Results of the pin genes with differentexpression patterns in B. juncea suggested the presence of a gene family.

  12. Investigation into Z-Pin Reinforced Composite Skin/Stiffener Debond under Monotonic and Cyclic Bending

    Science.gov (United States)

    Zhang, Xiangyang; Li, Yong; Van Hoa, Suong; Xiao, Jun; Chu, Qiyi

    2017-08-01

    Skin/stiffener debonding has been a longstanding concern for the users of stiffened composite panels in long-term service. Z-pinning technology is an emerging solution to reinforce the composite assembly joints. This work experimentally characterizes the progressive debonding of Z-pinned skin/stiffener interface with the skin under static bend loading. The three-stage failure process is identified as: flange edge debonding, pin/laminate debonding, and ultimate structural failure. Three different distribution patterns were compared in terms of the static debonding properties revealed the affirmative fact that locating pins in high normal stress regions, that is close to the flange edges in skin/stiffener structures, is more beneficial to utilize the full potential of Z-pinning reinforcement. The unit strip FE model was developed and demonstrated effective to analysis the effect of Z-pin distribution on the ultimate debond load. On the other hand, the evolution of fatigue cracks at Z-pinned skin/flange interface was investigated with a series of displacement-controlled fatigue bending tests and microscopic observations. Results show that Z-pinning postpones crack initiations at low displacement levels, and the remarkable crack-arresting function of pins enables the structure a prolonged fatigue life. However, pins become less effective when the maximum displacement exceeds the crack initiation level due to gradually pullout of pins.

  13. Maternal control of PIN1 is required for female gametophyte development in Arabidopsis.

    Directory of Open Access Journals (Sweden)

    Luca Ceccato

    Full Text Available Land plants are characterised by haplo-diploid life cycles, and developing ovules are the organs in which the haploid and diploid generations coexist. Recently it has been shown that hormones such as auxin and cytokinins play important roles in ovule development and patterning. The establishment and regulation of auxin levels in cells is predominantly determined by the activity of the auxin efflux carrier proteins PIN-FORMED (PIN. To study the roles of PIN1 and PIN3 during ovule development we have used mutant alleles of both genes and also perturbed PIN1 and PIN3 expression using micro-RNAs controlled by the ovule specific DEFH9 (DEFIFICENS Homologue 9 promoter. PIN1 down-regulation and pin1-5 mutation severely affect female gametophyte development since embryo sacs arrest at the mono- and/or bi-nuclear stages (FG1 and FG3 stage. PIN3 function is not required for ovule development in wild-type or PIN1-silenced plants. We show that sporophytically expressed PIN1 is required for megagametogenesis, suggesting that sporophytic auxin flux might control the early stages of female gametophyte development, although auxin response is not visible in developing embryo sacs.

  14. Active cloaking for clusters of pins in thin plates

    CERN Document Server

    O'Neill, Jane; Haslinger, Stewart; Movchan, Natasha; Craster, Richard

    2016-01-01

    This paper considers active cloaking of a square array of evenly spaced pins in a Kirchhoff plate in the presence of flexural waves. Active sources are distributed exterior to the cluster and are represented by the non-singular Green's function for the biharmonic operator. The complex amplitudes of the active sources, which cancel out selected multipole orders of the scattered field, are found by solving an algebraic system of equations. For frequencies in the zero-frequency stop band, we find that a small number of active sources located on a grid is sufficient for cloaking. For higher frequencies, we achieve efficient cloaking with the active sources positioned on a circle surrounding the cluster. We demonstrate the cloaking efficiency with several numerical illustrations, considering key frequencies from band diagrams and dispersion surfaces for a Kirchhoff plate pinned in a doubly periodic fashion.

  15. Study of the Radiation-Hardness of VCSEL and PIN

    CERN Document Server

    Gan, K K; Fernando, W; Kagan, H P; Kass, R D; Lebbai, M R M; Merritt, H; Moore, J R; Nagarkar, A; Rizatdinova, F; Skubic, P L; Smith, D S; Strang, M

    2009-01-01

    The silicon trackers of the ATLAS experiment at the Large Hadron Collider (LHC) at CERN (Geneva) use optical links for data transmission. An upgrade of the trackers is planned for the Super LHC (SLHC), an upgraded LHC with ten times higher luminosity. We study the radiation-hardness of VCSELs (Vertical-Cavity Surface-Emitting Laser) and GaAs and silicon PINs using 24 GeV/c protons at CERN for possible application in the data transmission upgrade. The optical power of VCSEL arrays decreases significantly after the irradiation but can be partially annealed with high drive currents. The responsivities of the PIN diodes also decrease significantly after irradiation, but can be recovered by operating at higher bias voltage. This provides a simple mechanism to recover from the radiation damage.

  16. Decrease of bulk pinning strength in deoxygenated YBCO single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, A.J.; Bekeris, V. [Buenos Aires Univ. (Argentina). Lab. de Bajas Temperaturas

    2000-07-01

    We measured the first and third harmonics of the complex AC susceptibility in YBCO single crystals with different oxygen contents (6.5 {<=} x {<=} 7). The amplitude of the AC field was varied in presence of an external dc field both applied parallel to the c-axis of the crystals. We give evidence that deoxygenation leads to a reduction of the bulk pinning strength and consequently to a stronger contribution of geometrical barriers. These results support the recently reported investigations showing that deoxygenation makes the YBCO crystals more anisotropic reducing the effective bulk pinning for quasi two-dimensional vortices. We also show measurements for the same crystals with the AC field applied perpendicular to the c-axis. (orig.)

  17. Turbine blade and non-integral platform with pin attachment

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, Christian Xavier; Eng, Darryl; Marra, John J.

    2016-08-02

    Platforms (36, 38) span between turbine blades (23, 24, 25) on a disk (32). Each platform may be individually mounted to the disk by a pin attachment (42). Each platform (36) may have a rotationally rearward edge portion (50) that underlies a forward portion (45) of the adjacent platform (38). This limits centrifugal bending of the rearward portion of the platform, and provides coolant sealing. The rotationally forward edge (44A, 44B) of the platform overlies a seal element (51) on the pressure side (28) of the forwardly adjacent blade, and does not underlie a shelf on that blade. The pin attachment allows radial mounting of each platform onto the disk via tilting (60) of the platform during mounting to provide mounting clearance for the rotationally rearward edge portion (50). This facilitates quick platform replacement without blade removal.

  18. Pinning control of a generalized complex dynamical network model

    Institute of Scientific and Technical Information of China (English)

    Huizhong YANG; Li SHENG

    2009-01-01

    This paper investigates the local and global synchronization of a generalized complex dynamical network model with constant and delayed coupling.Without assuming symmetry of the couplings,we proved that a single controller can pin the generalized complex network to a homogenous solution.Some previous synchronization results are generalized.In this paper,we first discuss how to pin an array of delayed neural networks to the synchronous solution by adding only one controller.Next,by using the Lyapunov functional method,some sufficient conditions are derived for the local and global synchronization of the coupled systems.The obtained results are expressed in terms of LMIs,which can be efficiently checked by the Matlab LMI toolbox.Finally,an example is given to illustrate the theoretical results.

  19. Matching of the Flux Lattice to Geometrically Frustrated Pinning Arrays

    Science.gov (United States)

    Trastoy, J.; Bernard, R.; Briatico, J.; Villegas, J. E.; Lesueur, J.; Ulysse, C.; Faini, G.

    2013-03-01

    We use vortex dynamics on artificial nanoscale energy landscapes as a model to experimentally investigate a problem inspired by ``spin ice'' systems. In particular, we study the matching of the flux lattice to pinning arrays in which the geometrical frustration is expected to impede a unique stable vortex configuration and to promote metastability. This is done with YBCO films in which the nanoscale vortex energy landscape is fabricated via masked ion irradiation. Surprisingly, we found that minimal changes in the distance between pinning sites lead to the suppression of some of the magneto-resistance matching effects, that is, for certain well-defined vortex densities. This effect strongly depends on the temperature. We argue that this behavior can be explained considering the arrays' geometrical frustration and the thermally activated reconfiguration of the vortex lattice between isoenergetic states. Work supported by the French ANR via SUPERHYRBIDS-II and ``MASTHER,'' and the Galician Fundacion Barrie

  20. Boiling of HFE-7100 on a Straight Pin Fin

    Institute of Scientific and Technical Information of China (English)

    Z. W. Liu; W.W. Lin; D.J. Lee; J.P. Hsu

    2001-01-01

    This paper deals with an experimental investigation of pin fin boiling of saturated and subcooled HFE-7100 under atmospheric pressure. Fin base temperature and heat flux data are measured along with the fin tip temperature. The basic features of boiling stability of HFE-7100 boiling on pin fin had been reported for the first time. For a given liquid/heating surface combination there exist upper steady-state (USS) branch and lower steady-state (LSS)branch, and a large, unstable regime located in between. Zones with different stability characteristics are mapped according to boiling on fins with different aspect ratios. Liquid subcooling can largely enhance heat transfer performance. A longer fin can provide a safer operation.

  1. Silicon pin solar cells investigated by multi-frequency EDMR

    Energy Technology Data Exchange (ETDEWEB)

    Meier, Christoph; Teutloff, Christian; Behrends, Jan; Bittl, Robert [Fachbereich Physik, Freie Universitaet Berlin, Arnimallee 14, 14195 Berlin (Germany); Fehr, Matthias; Schnegg, Alexander; Lips, Klaus [Institut fuer Silizium-Photovoltaik, Helmholtz-Zentrum Berlin fuer Materialien und Energie, Kekulestr. 5, 12489 Berlin (Germany)

    2011-07-01

    Electrically detected magnetic resonance (EDMR) can be used to investigate paramagnetic centres influencing charge transport in semiconductors even at concentrations well below the sensitivity threshold of conventional electron paramagnetic resonance (EPR). This technique measures conductivity changes in the sample that occur when spin transitions cause an enhancement or a quenching of currents. EDMR was e.g. successfully employed to microcrystalline Si pin solar cells in X-band (9.7 GHz). We present the application of EDMR to Si pin solar cells at Q-band frequency (34 GHz). We could demonstrate a gain of spectral resolution. With multi-frequency EDMR we distinguished between field-dependent and field-independent interactions. Further, we realized EDMR in a non-resonant setup at 94 GHz (W-band) and show first results.

  2. Turbine blade and non-integral platform with pin attachment

    Science.gov (United States)

    Campbell, Christian X; Eng, Darryl; Marra, John J

    2015-01-27

    Platforms (36, 38) span between turbine blades (23, 24, 25) on a disk (32). Each platform may be individually mounted to the disk by a pin attachment (42). Each platform (36) may have a rotationally rearward edge portion (50) that underlies a forward portion (45) of the adjacent platform (38). This limits centrifugal bending of the rearward portion of the platform, and provides coolant sealing. The rotationally forward edge (44A, 44B) of the platform overlies a seal element (51) on the pressure side (28) of the forwardly adjacent blade, and does not underlie a shelf on that blade. The pin attachment allows radial mounting of each platform onto the disk via tilting (60) of the platform during mounting to provide mounting clearance for the rotationally rearward edge portion (50). This facilitates quick platform replacement without blade removal.

  3. Debonding analyses of closely spaced Z-pins bridging an unbonded interface

    DEFF Research Database (Denmark)

    Legarth, Brian Nyvang

    2009-01-01

    In this study the plasticity, the spatial stress distribution and the debonding behavior of a metallic Z-pin bridging the unbonded interface between two substrates of an elasto-plastic material subjected to shear loading (mode II) are analyzed numerically by the finite element method taking full...... along the interface between the Z-pin and the substrates. The plastic zone in the Z-pin initiates in the center and spreads out along the two edges leaving elastic regions in the middle of the ends of the Z-pin. Similar behavior is seen for a Z-pin inclined to have loading against the inclination, while...... the plastic zone in a Z-pin inclined to have loading with the inclination only grows along one of the two edges of the Z-pin....

  4. Enhancing speed of pinning synchronizability: low-degree nodes with high feedback gains

    CERN Document Server

    Zhou, Ming-Yang; Liao, Hao; Fu, Zhong-Qian; Cai, Shi-Min

    2015-01-01

    Controlling complex networks is of paramount importance in science and engineering. Despite recent efforts to improve controllability and synchronous strength, little attention has been paid to the speed of pinning synchronizability (rate of convergence in pinning control) and the corresponding pinning node selection. To address this issue, we propose a hypothesis to restrict the control cost, then build a linear matrix inequality related to the speed of pinning controllability. By solving the inequality, we obtain both the speed of pinning controllability and optimal control strength (feedback gains in pinning control) for all nodes. Interestingly, some low-degree nodes are able to achieve large feedback gains, which suggests that they have high influence on controlling system. In addition, when choosing nodes with high feedback gains as pinning nodes, the controlling speed of real systems is remarkably enhanced compared to that of traditional large-degree and large-betweenness selections. Thus, the proposed...

  5. Melt Rate Improvement for DWPF MB3: Summary and Recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.P.

    2001-07-11

    The objective for this task is to understand and apply the control of glass batch chemistry (frit composition) and/or changes in chemical processing strategies to improve the overall melting process for Macrobatch 3 (MB3) (Defense Waste Processing Facility (DWPF) sludge-only processing). For melt rate limited systems, a small increase in melting efficiency translates into substantial savings by reducing operational costs without compromising the quality of the final waste product. This report summarizes the key information collected during the FY01 melt-rate testing completed to support the conclusion that switching from Frit 200, the frit currently used to prepare all the glass produced in radioactive processing, to Frit 320 should improve the melt rate during processing of DWPF MB3 sludge (Note: MB3 is referred to as Sludge Batch 2 in the High-Level Waste System Plan). The report also includes recommendations that should be addressed prior to implementation of the new frit and future research that should be completed to further improve melt rate. No analysis has been completed to determine if Frit 320 can be used in processing of other sludge macrobatches. The testing in this report is based on dried-slurry testing of a MB3 melter feed prepared from nonradioactive simulants. Additional testing, particularly with a melter feed slurry and actual waste, would be required before implementing the new frit in DWPF, and a variability study would also be necessary. The work to date, at most, provides relative data until actual melter data can be obtained and compared.

  6. Evaluation of PWR and BWR pin cell benchmark results

    Energy Technology Data Exchange (ETDEWEB)

    Pilgroms, B.J.; Gruppelaar, H.; Janssen, A.J. (Netherlands Energy Research Foundation (ECN), Petten (Netherlands)); Hoogenboom, J.E.; Leege, P.F.A. de (Interuniversitair Reactor Inst., Delft (Netherlands)); Voet, J. van der (Gemeenschappelijke Kernenergiecentrale Nederland NV, Dodewaard (Netherlands)); Verhagen, F.C.M. (Keuring van Electrotechnische Materialen NV, Arnhem (Netherlands))

    1991-12-01

    Benchmark results of the Dutch PINK working group on the PWR and BWR pin cell calculational benchmark as defined by EPRI are presented and evaluated. The observed discrepancies are problem dependent: a part of the results is satisfactory, some other results require further analysis. A brief overview is given of the different code packages used in this analysis. (author). 14 refs.; 9 figs.; 30 tabs.

  7. ANTICIPATING WPS PIN VULNERABILITY TO SECURE WIRELESS NETWORK

    Directory of Open Access Journals (Sweden)

    Indra Dwi Rianto

    2013-11-01

    Full Text Available WiFi Protected Setup (WPS is a standardized function supported by numerous vendors of wireless routers and access point to help set up connection to a wireless local area network. It is designed to simplify the set up and generally enabled by default. Due to design flaw, the WPS or QSS PIN is susceptible to a brute force attack. In this paper, we test the security vulnerability occurred, evaluate the performance and give recommendations to anticipate the attack.

  8. Evaluation of rodded BWR assembly pin powers with simulate

    Energy Technology Data Exchange (ETDEWEB)

    Bahadir, T. [Studsvik Scandpower, Inc., 309 Waverly Oaks Road (United States); Lindahl, S. Oe. [Studsvik Scandpower AB, Stensborgsgatan 4, SE-721 32 Vaesteraas (Sweden)

    2012-07-01

    In the development of Studsvik's nodal code SIMULATE5, special attention has been given to the accurate description of pin powers. The code solves the multi-group diffusion or simplified P3 equations with high spatial resolution. A short description is given of the handling of material heterogeneities in the axial and radial directions - the axial re-homogenization and the radial sub-mesh model, respectively. Furthermore, two models which are of special importance in the presence of control rods, and hence on the pellet clad interaction (PCI) phenomenon, are described; the quarter-assembly thermal-hydraulic treatment and the depletion of absorber material. A numerical example for a real core shows that while the impact of the fine grained description is negligible on global parameters such as k{sub eff}, the effect on pin powers may be substantial. For a deeply inserted and highly depleted control rod, the difference in pin powers caused by neglecting the advanced models of SIMULATE5, may be as high as 15 %. (authors)

  9. Passive Micro Vibration Isolator Utilizing Flux Pinning Effect for Satellites

    Science.gov (United States)

    Shibata, Takuma; Sakai, Shin-ichiro

    2016-09-01

    Information related to the origin of space and evolution of galaxy can be obtained using the observation satellites. In recent years, high pointing accuracy is demanded for getting more detailed data about distant stars and galaxies. As a result, vibration isolators that consist of a main structure and a TTM (Tip Tilt Mirror) have been adopted for observation satellites. However, cutting the low frequency vibrations off passively with the conventional methods is difficult. A vibration isolator that uses pinning effect is proposed for solving this problem. The pinning effect is acquired by cooling the type-II superconductor below the critical temperature and it generates a pinning force to maintain the relative distance and attitude between a type- II superconductor and a material that generates magnetic flux. The mission part and the bus part of the satellite are equipped with superconductors and permanent magnets and these parts perform short distance formation flight by applying the effect. This method can cut vibrations from low to high frequency bands off passively. In addition, Meissner effect can prevent collision of the mission and bus parts. In order to investigate the performance of this system, experiments and simulations are carried out and the results are discussed.

  10. Safety pin suture for management of atonic postpartum hemorrhage.

    Science.gov (United States)

    Mostfa, Ali Abdelhamed M; Zaitoun, Mostafa M

    2012-01-01

    Objective. To assess the efficacy of a new suture technique in controlling severe resistant uterine atonic postpartum hemorrhage. Patients and Methods. This is a retrospective observational study that included thirteen women with uterine atony and postpartum bleeding that did not react to usual medical management. All these women underwent compressing vertical suture technique in which the anterior and posterior walls of the uterus were attached so as to compress the uterus. The suture is transfixed at the uterine fundus, thus eliminating the risk of sutures sliding off at the uterine fundus (safety pin suture). Results. safety pin uterine compression suture was a sufficient procedure to stop the bleeding immediately in 92.2% of the women. None of the women developed complications related to the procedure. Conclusion. A new safety pin suture is a simple and effective procedure to control bleeding in patients with treatment-resistant, life-threatening atonic postpartum hemorrhage with the advantage of eliminating the risk of the sutures sliding off at the uterine fundus.

  11. Contact and Non-contact Measurements of Grinding Pins

    Directory of Open Access Journals (Sweden)

    Magdziak Marek

    2015-01-01

    Full Text Available The paper presents the results of contact and non-contact measurements of external profiles of selected grinding pins. The measurements were conducted in order to choose the appropriate measuring technique in the case of the considered measurement task. In the case of contact measurements the coordinate measuring machine ACCURA II was applied. The used coordinate measuring machine was equipped with the contact scanning probe VAST XT and the Calypso inspection software. Contact coordinate measurements were performed by using of different measurement strategies. The applied strategies included different scanning velocities and distances between measured points. Non-contact measurements were conducted by means of the tool presetter produced by the Mahr company. On the basis of gained results the guidelines concerning measurements of grinding pins were formulated. The measurements of analyzed grinding pins performed by means of the non-contact measuring system are characterized by higher reproducibility than the contact measurements. The low reproducibility of contact measurements may be connected with the inaccuracy of the selected coordinate measuring machine and the measuring probe, the measurement parameters and environmental conditions in the laboratory where the coordinate measuring machine is located. Moreover, the paper presents the possible application of results of conducted investigations. The results of non-contact measurements can be used in the simulation studies of grinding processes. The simulations may reduce the costs of machining processes.

  12. OntoPIN: an ontology-annotated PPI database.

    Science.gov (United States)

    Guzzi, Pietro Hiram; Veltri, Pierangelo; Cannataro, Mario

    2013-09-01

    Protein-protein interaction (PPI) data stored in publicly available databases are queried by the use of simple query interfaces allowing only key-based queries. A typical query on such databases is based on the use of protein identifiers and enables the retrieval of one or more proteins. Nevertheless, a lot of biological information is available and is spread on different sources and encoded in different ontologies such as Gene Ontology. The integration of existing PPI databases and biological information may result in richer querying interfaces and successively could enable the development of novel algorithms that may use biological information. The OntoPIN project showed the effectiveness of the introduction of a framework for the ontology-based management and querying of Protein-Protein Interaction Data. The OntoPIN framework first merges PPI data with annotations extracted from existing ontologies (e.g. Gene Ontology) and stores annotated data into a database. Then, a semantic-based query interface enables users to query these data by using biological concepts. OntoPIN allows: (a) to extend existing PPI databases by using ontologies, (b) to enable a key-based querying of annotated data, and (c) to offer a novel query interface based on semantic similarity among annotations.

  13. The dynamics of plant plasma membrane proteins: PINs and beyond.

    Science.gov (United States)

    Luschnig, Christian; Vert, Grégory

    2014-08-01

    Plants are permanently situated in a fixed location and thus are well adapted to sense and respond to environmental stimuli and developmental cues. At the cellular level, several of these responses require delicate adjustments that affect the activity and steady-state levels of plasma membrane proteins. These adjustments involve both vesicular transport to the plasma membrane and protein internalization via endocytic sorting. A substantial part of our current knowledge of plant plasma membrane protein sorting is based on studies of PIN-FORMED (PIN) auxin transport proteins, which are found at distinct plasma membrane domains and have been implicated in directional efflux of the plant hormone auxin. Here, we discuss the mechanisms involved in establishing such polar protein distributions, focusing on PINs and other key plant plasma membrane proteins, and we highlight the pathways that allow for dynamic adjustments in protein distribution and turnover, which together constitute a versatile framework that underlies the remarkable capabilities of plants to adjust growth and development in their ever-changing environment.

  14. PIN1 in hepatocellular carcinoma is associated with TP53 gene status.

    Science.gov (United States)

    Bae, Jun Sang; Noh, Sang Jae; Kim, Kyoung Min; Jang, Kyu Yun; Park, Ho Sung; Chung, Myoung Ja; Park, Byung-Hyun; Moon, Woo Sung

    2016-10-01

    Phosphorylation of proteins on serine/threonine residues that precede proline (pSer/Thr-Pro) is specifically catalyzed by the peptidyl-prolyl cis-trans isomerase PIN1. PIN1-mediated prolyl-isomerization induces cell cycle arrest and growth inhibition through the regulation of target proteins, including TP53. We examined whether PIN1 acts in a different manner according to TP53 gene status in hepatocellular carcinoma (HCC). We investigated the expression of PIN1 and TP53 proteins in 119 HCC tissue samples. We also analyzed PIN1 expression in combination with TP53 gene mutation and its correlation with the clinical outcome. In addition, we used synthetic small interfering RNA to silence PIN1 gene expression in TP53 wild-type and TP53 mutant HCC cell lines, and then evaluated cell proliferation, migration and invasion. Expression of PIN1 was strongly associated with expression of TP53 protein or TP53 mutation of HCC samples. PIN1 and TP53 expression in TP53 mutant HCC cell lines was higher than that in TP53 wild-type HCC cell lines. Silencing of PIN1 in HLE cells containing mutant TP53 significantly decreased cell proliferation, migration and invasion. In contrast to PIN1 silencing in HLE cells, PIN1 silencing in HepG2 cells containing functional wild-type TP53 resulted in enhanced tumor cell proliferation. HCC patients bearing PIN1 expression with wild-type TP53 were predicted to demonstrate favorable relapse-free survival. Our results suggest that PIN1 plays a role in cancer cell proliferation, migration and invasion in a different manner according to the TP53 gene mutation status in HCC. In particular, interaction of PIN1 with mutant TP53 can act as a tumor promoter and increase its oncogenic activities in HCC.

  15. Pin-wise Reactor Analysis Based on the Generalized Equivalence Theory

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Hwan Yeal; Heo, Woong; Kim, Yong Hee [KAIST, Daejeon (Korea, Republic of)

    2016-05-15

    In this paper, a pin-wise reactor analysis is performed based on the generalized equivalence theory. From the conventional fuel assembly lattice calculations, pin-wise 2-group cross sections and pin DFs are generated. Based on the numerical results on a small PWR benchmark, it is observed that the pin-wise core analysis provide quite accurate prediction on the effective multiplication factor and the peak pin power error is bounded by about 3% in peripheral fuel assemblies facing the baffle-reflector. Also, it was found that relatively large pin power errors occur along the interface between clearly different fuel assemblies. It is expected that the GET-based pin-by-pin core calculation can be further developed as an advanced method for reactor analysis via improving the group constants and discontinuity factors. Recently, high-fidelity multi-dimensional analysis tools are gaining more attention because of their accurate prediction of local parameters for core design and safety assessment. In terms of accuracy, direct whole-core transport is quite promising. However, it is clear that it is still very costly in terms of the computing time and memory requirements. Another possible solution is the pin-by-pin core analysis in which only small fuel pins are homogenized and the 3-D core analysis is still performed using a low-order operator such as the diffusion theory. In this paper, a pin-by-pin core analysis is performed using the hybrid CMFD (HCMFD) method. Hybrid CMFD is a new global-local iteration method that has been developed for efficient parallel calculation of pinby-pin heterogeneous core analysis. For the HCMFD method, the one-node CMFD scheme is combined with a local two-node CMFD method in a non-linear way. Since the SPH method is iterative and SPH factors are not direction dependent, it is clear that SPH method takes more computing cost and cannot take into account the different heterogeneity and transport effects at each pin interface. Unlike the SPH

  16. Magnetic Biocomposites for Remote Melting.

    Science.gov (United States)

    Zhou, Mengbo; Liebert, Tim; Müller, Robert; Dellith, Andrea; Gräfe, Christine; Clement, Joachim H; Heinze, Thomas

    2015-08-10

    A new approach toward the fabrication of biocompatible composites suitable for remote melting is presented. It is shown that magnetite nanoparticles (MNP) can be embedded into a matrix of biocompatible thermoplastic dextran esters. For that purpose, fatty acid esters of dextran with adjustable melting points in the range of 30-140 °C were synthesized. Esterification of the polysaccharide by activation of the acid as iminium chlorides guaranteed mild reaction conditions leading to high quality products as confirmed by FTIR- and NMR spectroscopy as well as by gel permeation chromatography (GPC). A method for the preparation of magnetically responsive bionanocomposites was developed consisting of combined dissolution/suspension of the dextran ester and hydrophobized MNPs in an organic solvent followed by homogenization with ultrasonication, casting of the solution, drying and melting of the composite for a defined shaping. This process leads to a uniform distribution of MNPs in nanocomposite as revealed by scanning electron microscope. Samples of different geometries were exposed to high frequency alternating magnetic field. It could be shown that defined remote melting of such biocompatible nanocomposites is possible for the first time. This may lead to a new class of magnetic remote control systems, which are suitable for controlled release applications or self-healing materials.

  17. UNCONSTRAINED MELTING AND SOLIDIFICATION INSIDE ...

    African Journals Online (AJOL)

    2015-09-01

    Sep 1, 2015 ... Department of Mechanical Engineering, Sari Branch, Islamic Azad University, ... at initial time of melting process where the layer of liquid PCM near hot ... They carried out the simulation at different Rayleigh numbers ranging from 10 .... An enthalpy-porosity technique [28] is used in FLUENT for modeling the.

  18. Thermodynamics of freezing and melting

    DEFF Research Database (Denmark)

    Pedersen, Ulf Rørbæk; Costigliola, Lorenzo; Bailey, Nicholas

    2016-01-01

    phases at a single thermodynamic state point provide the basis for calculating the pressure, density and entropy of fusion as functions of temperature along the melting line, as well as the variation along this line of the reduced crystalline vibrational mean-square displacement (the Lindemann ratio...

  19. X-ray measurement with Pin type semiconductor detectors; Medicion de rayos X con detectores de semiconductor tipo PIN

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez J, F.J. [Instituto Nacional de Investigaciones Nucleares, Departamento de Electronica, C.P. 52045 Salazar, Estado de Mexico (Mexico)

    2000-07-01

    Here are presented the experimental results of the applications of Pin type radiation detectors developed in a National Institute of Nuclear Research (ININ) project, in the measurement of low energy gamma and X-rays. The applications were oriented mainly toward the Medical Physics area. It is planned other applications which are in process of implementation inside the National Institute of Nuclear Research in Mexico. (Author)

  20. Feasibility of re-melting NORM-contaminated scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Winters, S. J.; Smith, K. P.

    1999-10-26

    Naturally occurring radioactive materials (NORM) sometimes accumulate inside pieces of equipment associated with oil and gas production and processing activities. Typically, the NORM accumulates when radium that is present in solution in produced water precipitates out in scale and sludge deposits. Scrap equipment containing residual quantities of these NORM-bearing scales and sludges can present a waste management problem if the radium concentrations exceed regulatory limits or activate the alarms on radiation screening devices installed at most scrap metal recycling facilities. Although NORM-contaminated scrap metal currently is not disposed of by re-melting, this form of recycling could present a viable disposition option for this waste stream. Studies indicate that re-melting NORM-contaminated scrap metal is a viable recycling option from a risk-based perspective. However, a myriad of economic, regulatory, and policy issues have caused the recyclers to turn away virtually all radioactive scrap metal. Until these issues can be resolved, re-melting of the petroleum industry's NORM-impacted scrap metal is unlikely to be a widespread practice. This paper summarizes the issues associated with re-melting radioactive scrap so that the petroleum industry and its regulators will understand the obstacles. This paper was prepared as part of a report being prepared by the Interstate Oil and Gas Compact Commission's NORM Subcommittee.

  1. Cell plate-restricted association of Arabidopsis dynamin related proteins and PIN auxin efflux carriers is required for PIN endocytic trafficking during cytokinesis.

    NARCIS (Netherlands)

    Mravec, J.; Petrasek, J.; Li, N.; Boeren, J.A.; Karlova, R.B.; Kitakura, S.; Naramoto, S.; Nodzynski, T.; Dhonukshe, P.B.; Vries, de S.C.; Zazimalova, E.; Friml, J.

    2011-01-01

    The polarized transport of the phytohormone auxin [1], which is crucial for the regulation of different stages of plant development [ [2] and [3] ], depends on the asymmetric plasma membrane distribution of the PIN-FORMED (PIN) auxin efflux carriers [4 A. Vieten, M. Sauer, P.B. Brewer and J. Friml,

  2. Peristaltic closure of a safety pin--an unusual fate of a safety pin seen as a foreign body in the gastrointestinal tract.

    Science.gov (United States)

    Andréasson, L; Ingelstedt, S; Tjernström, O

    1986-04-01

    This report presents a case where an open safety pin passed through the Esophagus and where Nature herself finally solved the problem by closing the pin, which was afterwards carried in the faecal stream and discharged from the body without any harm to the patient.

  3. Cell plate-restricted association of Arabidopsis dynamin related proteins and PIN auxin efflux carriers is required for PIN endocytic trafficking during cytokinesis.

    NARCIS (Netherlands)

    Mravec, J.; Petrasek, J.; Li, N.; Boeren, J.A.; Karlova, R.B.; Kitakura, S.; Naramoto, S.; Nodzynski, T.; Dhonukshe, P.B.; Vries, de S.C.; Zazimalova, E.; Friml, J.

    2011-01-01

    The polarized transport of the phytohormone auxin [1], which is crucial for the regulation of different stages of plant development [ [2] and [3] ], depends on the asymmetric plasma membrane distribution of the PIN-FORMED (PIN) auxin efflux carriers [4 A. Vieten, M. Sauer, P.B. Brewer and J. Friml,

  4. Establishing the need for an engineering standard for agricultural hitch pins.

    Science.gov (United States)

    Deboy, G R; Knapp, W M; Field, W E; Krutz, G W; Corum, C L

    2012-04-01

    Documented incidents have occurred in which failure or unintentional disengagement of agricultural hitch pins has contributed to property damage and personal injury. An examination of current hitch pin use on a convenience sample of farm operations in Indiana revealed a variety of non-standard, worn and damaged, and inappropriately sized hitch pins in use. Informal interviews with the farm operators confirmed that hitch pin misuse, failure, or disengagement is a relatively widespread problem that remains largely unaddressed. On-site observations also suggested a low use of hitch pin retaining devices or safety chains. A review of prior research revealed that little attention has been given to this problem, and currently no documentation allows for an estimate of the frequency or severity of losses associated with hitch pin misuse, failure, or disengagement. No specific engineering standards were found that directly applied to the design, appropriate selection, or loading capacity of agricultural hitch pins. Major suppliers of replacement hitch pins currently provide little or no information on matching hitch pin size to intended applications, and most replacement hitch pins examined were of foreign origin, with the overwhelming majority imported from China or India. These replacement hitch pins provided no specifications other than diameter, length, and, in some cases, labeling that indicated that the pins had been "heat treated. " Testing of a sample of 11 commercially available replacement hitch pins found variation along the length of the pin shaft and between individual pins in surface hardness, a potential predictor of pin failure. Examination of 17 commercially available replacement pins also revealed a variety of identifiers used to describe pin composition and fabrication methods, e.g., "heat treated." None of the pins examined provided any specifications on loading capacity. It was therefore concluded that there is a need to develop an agricultural hitch

  5. Numerical modeling of friction stir welding using the tools with polygonal pins

    Directory of Open Access Journals (Sweden)

    M. Mehta

    2015-09-01

    Full Text Available Friction stir welding using the tools with polygonal pins is often found to improve the mechanical strength of weld joint in comparison to the tools with circular pins. However, the impacts of pin profile on the peak temperature, tool torque and traverse force, and the resultant mechanical stresses experienced by the tool have been rarely reported in a systematic manner. An estimation of the rate of heat generation for the tools with polygonal pins is challenging due to their non-axisymmetric cross-section about the tool axis. A novel methodology is presented to analytically estimate the rate of heat generation for the tools with polygonal pins. A three-dimensional heat transfer analysis of friction stir welding is carried out using finite element method. The computed temperature field from the heat transfer model is used to estimate the torque, traverse force and the mechanical stresses experienced by regular triangular, square, pentagon and hexagon pins following the principles of solid mechanics. The computed results show that the peak temperature experienced by the tool pin increases with the number of pin sides. However, the resultant maximum shear stress experienced by the pin reduces from the triangular to hexagonal pins.

  6. Connection stiffness and dynamical docking process of flux pinned spacecraft modules

    Science.gov (United States)

    Lu, Yong; Zhang, Mingliang; Gao, Dong

    2014-02-01

    This paper describes a novel kind of potential flux pinned docking system that consists of guidance navigation and control system, the traditional extrusion type propulsion system, and a flux pinned docking interface. Because of characteristics of passive stability of flux pinning, the docking control strategy of flux pinned docking system only needs a series of sequential control rather than necessary active feedback control, as well as avoidance of hazardous collision accident. The flux pinned force between YBaCuO (YBCO) high temperature superconductor bulk and permanent magnet is able to be given vent based on the identical current loop model and improved image dipole model, which can be validated experimentally. Thus, the connection stiffness between two flux pinned spacecraft modules can be calculated based on Hooke's law. This connection stiffness matrix at the equilibrium position has the positive definite performance, which can validate the passively stable connection of two flux pinned spacecraft modules theoretically. Furthermore, the relative orbital dynamical equation of two flux pinned spacecraft modules can be established based on Clohessy-Wiltshire's equations and improved image dipole model. The dynamical docking process between two flux pinned spacecraft modules can be obtained by way of numerical simulation, which suggests the feasibility of flux pinned docking system.

  7. Connection stiffness and dynamical docking process of flux pinned spacecraft modules

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yong; Zhang, Mingliang, E-mail: niudun12@126.com; Gao, Dong [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, Heilongjiang 150001 (China)

    2014-02-14

    This paper describes a novel kind of potential flux pinned docking system that consists of guidance navigation and control system, the traditional extrusion type propulsion system, and a flux pinned docking interface. Because of characteristics of passive stability of flux pinning, the docking control strategy of flux pinned docking system only needs a series of sequential control rather than necessary active feedback control, as well as avoidance of hazardous collision accident. The flux pinned force between YBaCuO (YBCO) high temperature superconductor bulk and permanent magnet is able to be given vent based on the identical current loop model and improved image dipole model, which can be validated experimentally. Thus, the connection stiffness between two flux pinned spacecraft modules can be calculated based on Hooke's law. This connection stiffness matrix at the equilibrium position has the positive definite performance, which can validate the passively stable connection of two flux pinned spacecraft modules theoretically. Furthermore, the relative orbital dynamical equation of two flux pinned spacecraft modules can be established based on Clohessy-Wiltshire's equations and improved image dipole model. The dynamical docking process between two flux pinned spacecraft modules can be obtained by way of numerical simulation, which suggests the feasibility of flux pinned docking system.

  8. Expression of Pin1 and Ki67 in Cervical Cancer and Their Significance

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    In order to investigate the expression levels of Pin1 mRNA and protein in cervical cancer and its association with Ki67 and their clinical significance, amplification of Pin1 gene was examined by RT-PCR, and the expression of both Pin1 and Ki67 protein was detected by immunohistochemistry in cervical cancer tissues. It was shown that the expression levels of Pin1 were higher in cervical cancer than in normal cervical tissues (P<0.05). The expression of Pin1 protein was increased progressively along with the disease process from normal cervix to CIN and to cervical cancer (P<0. 05). No significant difference in the Pin1 expression was found between disease stages (FIGO),pathological grades or pelvic lymph node metastasis status (P>0.05). The expression of Pin1 was significantly higher in adenocarcinoma than insquamous carcinoma of the uterine cervix (P<0.05).In cervical cancer, the overexpression of Pin1 was positively correlated with that of Ki67 (P<0.05). These results suggested that the overexpression of Pin1 was closely related with cancer cell proliferation or progression of cervical cancer and contributed to oncogenesis. Pin1 may serve as a potential marker for cervical cancer diagnosis.

  9. Pin1 promotes GR transactivation by enhancing recruitment to target genes.

    Science.gov (United States)

    Poolman, Toryn M; Farrow, Stuart N; Matthews, Laura; Loudon, Andrew S; Ray, David W

    2013-10-01

    The glucocorticoid receptor (GR) is a ligand activated transcription factor, serving to regulate both energy metabolism and immune functions. Factors that influence cellular sensitivity to glucocorticoids (GC) are therefore of great interest. The N-terminal of the GR contains numerous potential proline-directed phosphorylation sites, some of which can regulate GR transactivation. Unrestricted proline isomerisation can be inhibited by adjacent serine phosphorylation and requires a prolyl isomerise, Pin1. Pin1 therefore determines the functional outcome of proline-directed kinases acting on the GR, as cis/trans isomers are distinct pools with different interacting proteins. We show that Pin1 mediates GR transactivation, but not GR trans-repression. Two N-terminal GR serines, S203 and S211, are targets for Pin1 potentiation of GR transactivation, establishing a direct link between Pin1 and the GR. We also demonstrate GC-activated co-recruitment of GR and Pin1 to the GILZ gene promoter. The Pin1 effect required both its WW and catalytic domains, and GR recruitment to its GRE was Pin1-dependent. Therefore, Pin1 is a selective regulator of GR transactivation, acting through N-terminal phospho-serine residues to regulate GR recruitment to its target sites in the genome. As Pin1 is dysregulated in disease states, this interaction may contribute to altered GC action in inflammatory conditions.

  10. A Multi Response Optimization of Tool Pin Profile on the Tensile Behavior of Age-hardenable Aluminum Alloys during Friction Stir Welding

    Directory of Open Access Journals (Sweden)

    D. Vijayan

    2014-05-01

    Full Text Available The main aim of this study is to select a suitable tool pin profile to maximize the tensile behavior (Ultimate Tensile Strength and Tensile Elongation of Friction stir welded aluminum alloys of AA 2024 and AA 6061. The age-hardnable aluminum alloys of 2xxx, 6xxx and 7xxx series are extensively used in automobile and aircraft industries because of its high strength to weight ratio, formability and ductility. These alloys are vulnerable to cracking (2xxx and 7xxx and highly melt (6xxx in conventional fusion welding techniques. Friction stir welding is an emerging solid state welding technique which is best suitable for joining these aluminum alloys. The influential process and tool parameters that are affecting the FS welded joints are such as tool rotational speed, welding speed, axial load and tool pin profile. Dissimilar friction stir welded joints of AA 2024 and AA 6061 aluminum alloys are fabricated using a friction stir welding process to examine the influence of the tool pin profiles on tensile properties on various crucial process parameters. A Box-Behnken design with four input parameters, three levels and 30 runs is used to conduct the experiments and Response Surface Method (RSM is used to develop the mathematical model. The experimental results were predicted at the 95% confidence level. The macro defects in the welds and the modes of tensile fracture are discussed in detail to reveal the root cause of failure in the fabricated samples. The rotating tool equipped with a square pin generated the highest ultimate tensile strength (143 MPa with a 12% elongation. A microstructure variation on dissimilar alloys which result 44% reduction in tensile strength on AA2024 and 51% reduction in tensile strength on AA6061 aluminum alloys was observed on the stir zones.

  11. Basal terraces on melting ice shelves

    National Research Council Canada - National Science Library

    Dutrieux, Pierre; Stewart, Craig; Jenkins, Adrian; Nicholls, Keith W; Corr, Hugh F. J; Rignot, Eric; Steffen, Konrad

    2014-01-01

    Ocean waters melt the margins of Antarctic and Greenland glaciers, and individual glaciers' responses and the integrity of their ice shelves are expected to depend on the spatial distribution of melt...

  12. Asian Facilities

    Science.gov (United States)

    Nakahata, M.

    2011-04-01

    Asian underground facilities are reviewed. The YangYang underground Laboratory in Korea and the Kamioka observatory in Japan are operational and several astrophysical experiments are running. Indian Neutrino Observatory(INO) and China JinPing Underground Laboratory (CJPL) are under construction and underground experiments are being prepared. Current activities and future prospects at those underground sites are described.

  13. Filament stretching rheometry of polymer melts

    DEFF Research Database (Denmark)

    Hassager, Ole; Nielsen, Jens Kromann; Rasmussen, Henrik Koblitz

    2005-01-01

    The Filament Stretching Rheometry (FSR) method developed by Sridhar, McKinley and coworkers for polymer solutions has been extended to be used also for polymer melts. The design of a melt-FSR will be described and differences to conventional melt elongational rheometers will be pointed out. Results...

  14. Filament stretching rheometry of polymer melts

    DEFF Research Database (Denmark)

    Hassager, Ole; Nielsen, Jens Kromann; Rasmussen, Henrik Koblitz

    2005-01-01

    The Filament Stretching Rheometry (FSR) method developed by Sridhar, McKinley and coworkers for polymer solutions has been extended to be used also for polymer melts. The design of a melt-FSR will be described and differences to conventional melt elongational rheometers will be pointed out. Results...

  15. An Investigation on the Pin Bearings’ Optimization of a Hermetic Reciprocating Compressor

    Science.gov (United States)

    Ozdemir, A. R.; Hacioglu, B.; Kasapoglu, E.

    2015-08-01

    A hermetic reciprocating compressor is the most energy consuming component of the refrigerators. Therefore performance improvement studies of the compressor play an important role to reduce overall energy consumption of the refrigerators. Design of bearings is one of the major study areas influencing reciprocating compressor performance. In this study crank pin and piston pin bearings in hermetic compressor applications are investigated and optimized. The effect of operating conditions, bearing offset between crank pin and piston pin, bearing clearance and bearing location along the shaft on the friction loss were investigated and optimal bearing designs were developed. Efficiency measurements of the compressor showed that the improved crank pin and piston pin bearing designs provide up to 3.8% increase in the COP as a result of reduction in mechanical loss that is significantly influenced by the length of the bearings, bearing location along the shaft and operating conditions.

  16. SURFACE MELTING OF ALUMINIUM ALLOYS

    OpenAIRE

    Veit, S.; Albert, D; Mergen, R.

    1987-01-01

    The wear properties of aluminium base alloys are relatively poor. Laser surface melting and alloying has proved successful in many alloy systems as a means of significantly improving the surface properties. The present work describes experiments designed to establish the scope of laser treatment of aluminium alloys. Aluminium does not absorb CO2 laser light as well as other metals which necessitated first a general study of absorption caotings. Aluminium alloys offer fewer opportunities than ...

  17. Evaluation of PWR and BWR pin cell benchmark results

    Energy Technology Data Exchange (ETDEWEB)

    Pijlgroms, B.J.; Gruppelaar, H.; Janssen, A.J. (Unit Nuclear Energy, Netherlands Energy Research Foundation ECN, Petten (Netherlands)); Hoogenboorm, J.E.; De Leege, P.F.A. (International Reactor Institute IRI, University of Leiden, Leiden (Netherlands)); Van de Voet, J.; Verhagen, F.C.M. (KEMA NV, Arnhem (Netherlands))

    1992-01-01

    In order to carry out reliable reactor core calculations for a boiled water reactor (BWR) or a pressurized water reactor (PWR) first reactivity calculations have to be carried out for which several calculation programs are available. The purpose of the title project is to exchange experiences to improve the knowledge of this reactivity calculations. In a large number of institutes reactivity calculations of PWR and BWR pin cells were executed by means of available computer codes. Results are compared. It is concluded that the variations in the calculated results are problem dependent. Part of the results is satisfactory. However, further research is necessary.

  18. Pinning control of spatio temporal chaos in nonlinear optics

    Energy Technology Data Exchange (ETDEWEB)

    Mendoza, C; Martinez-Mardones, J [Institute of Physics, Pontifical Catholic University of Valparaiso, 234-0025 Valparaiso (Chile); Ramazza, P L; Boccaletti, S [CNR- Istituto dei Sistemi Complessi, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy)], E-mail: caromendoza@gmail.com

    2008-11-01

    We have studied numerically the influence of the number of controllers in the control of a spatial pattern in an optical device. In this article, we focus on the liquid crystal light valve (LCLV) which is known to exhibit spatio-temporal chaotic states in some range of parameters. By applying a correcting term in the intensity proportional to the difference between the light intensity of the target pattern and the chaos state, the system is driven to the target pattern in finite time. In addition, we study the number of pinning points and their positions to reach the control of the pattern.

  19. Analyzing the use of pins in safety bearings

    DEFF Research Database (Denmark)

    da Fonseca, Cesar A. L. L.; Weber, Hans I.; Fleischer, Philip F.

    2015-01-01

    A new concept for safety bearings is analyzed: useful in emergency situations, it shall protect the bearing from destruction by the use of pins which impact with a disc, both capable of good energy dissipation. Results of work in progress are presented by validating partial stages......, the variation of energy content of the disc after each contact is considered. Actually, the validation of the clamped-free rotor is done. The main goal is to design an automatic system with the capability of changing the gap when necessary in order to avoid the rotor colliding with the inner part of the bearing....

  20. Current Kink and Capacitance Frequency Dispersion in Silicon PIN Photodiodes

    Science.gov (United States)

    Guo, Xia; Feng, Yajie; Liu, Qiaoli; Wang, Huaqiang; Li, Chong; Hu, Zonghai; He, Xiaoying

    2017-09-01

    Silicon PIN photodiodes in the visible wavelength range have been widely applied in aerospace, defense, security, medical, and scientific instruments because of their high sensitivity and low cost. In this paper, the phenomena of the current kink and the capacitance frequency dispersion are observed. Contamination at the p-type Ohmic contact interface is proposed to explain the current kink effect and capacitance frequency dispersion, according to the temperature-dependent I-V measurement results in which trap-assisted tunneling process demonstrated.

  1. Melting Behaviour of Ferronickel Slags

    Science.gov (United States)

    Sagadin, Christoph; Luidold, Stefan; Wagner, Christoph; Wenzl, Christine

    2016-12-01

    The industrial manufacturing of ferronickel in electric furnaces produces large amounts of slag with strong acidic character and high melting points, which seriously stresses the furnace refractory lining. In this study, the melting behavior of synthetically produced ferronickel slags on magnesia as refractory material was determined by means of a hot stage microscope. Therefore, slags comprising the main oxides SiO2 (35-70 wt.%), MgO (15-45 wt.%) and Fe2O3 (5-35 wt.%) were melted in a graphite crucible and afterwards analyzed by a hot stage microscope. The design of experiments, which was created by the statistic software MODDE®, included 20 experiments with varying slag compositions as well as atmospheres. The evaluation of the test results occurred at three different characteristic states of the samples like the softening point according to DIN 51730 and the temperatures at which the area of residual cross-section of the samples amounted to 30% and 40%, respectively, of the original value depending of their SiO2/MgO ratio and iron oxide content. Additionally, the thickness of the zone influenced by the slag was measured and evaluated.

  2. Optimization of the Brass Melting

    Directory of Open Access Journals (Sweden)

    Biernat S.

    2014-08-01

    Full Text Available The article describes the optimization of the melting brass. Brasses, as one of the most popular alloys of copper, deserve special attention in the context of the processes of melting, which in turn would provide not only products of better quality, but also reduce the cost of their production or refining. For this purpose, several studies carried out deriatographic (DTA and thermogravimetric (TG using derivatograph. The results were confronted with the program SLAG - PROP used to evaluate the physicochemical properties of the coatings extraction. Based on the survey and analysis of the program can identify the most favorable physico - chemical properties, which should be carried out treatments. This allows for slag mixtures referred configurations oxide matrix containing specific stimulators of the reaction. Conducted empirical studies indicate a convergence of the areas proposed by the application. It should also be noted that the program also indicates additional areas in which to carry out these processes would get even better, to optimize the melting process, the results.

  3. Biomechanical and Cost Comparisons of Near-Far and Pin-Bar Constructs.

    Science.gov (United States)

    Whitney Kluk, Augusta; Zhang, Tina; Russell, Joseph P; Kim, Hyunchul; Hsieh, Adam H; O'Toole, Robert V

    2017-03-01

    Orthopedic dogma states that external fixator stiffness is improved by placing 1 pin close to the fracture and 1 as distant as possible ("near-far"). This fixator construct is thought to be less expensive than placing pins a shorter distance apart and using "pin-bar" clamps that attach pins to outriggers. The authors therefore hypothesized that the near-far construct is stiffer and less expensive. They compared mechanical stiffness and costs of near-far and pin-bar constructs commonly used for temporary external fixation of femoral shaft fractures. Their testing model simulated femoral shaft fractures in damage control situations. Fourth-generation synthetic femora (n=18) were used. The near-far construct had 2 pins that were 106 mm apart, placed 25 mm from the gap on each side of the fracture. The pin-bar construct pins were 55 mm apart, placed 40 mm from the gap. Mechanical testing was performed on a material test system machine. Stiffness was determined in the linear portion of the load-displacement curve for both constructs in 4 modes: axial compression, torsional loading, frontal plane 3-point bending, and sagittal plane 3-point bending. Costs were determined from a 2012 price guide. Compared with the near-far construct, the pin-bar construct had stiffness increased by 58% in axial compression (P<.05) and by 52% in torsional loading (P<.05). The pin-bar construct increased cost by 11%. In contrast to the authors' hypothesis and existing orthopedic dogma, the near-far construct was less stiff than the pin-bar construct and was similarly priced. Use of the pin-bar construct is mechanically and economically reasonable. [Orthopedics. 2017; 40(2):e238-e241.]. Copyright 2016, SLACK Incorporated.

  4. The PIN1 family gene PvPIN1 is involved in auxin-dependent root emergence and tillering in switchgrass

    Directory of Open Access Journals (Sweden)

    Kaijie Xu

    2016-03-01

    Full Text Available Abstract Switchgrass (Panicum virgatum L.; family Poaceae is a warm-season C4 perennial grass. Tillering plays an important role in determining the morphology of aboveground parts and the final biomass yield of switchgrass. Auxin distribution in plants can affect a variety of important growth and developmental processes, including the regulation of shoot and root branching, plant resistance and biological yield. Auxin transport and gradients in plants are mediated by influx and efflux carriers. PvPIN1, a switchgrass PIN1-like gene that is involved in regulating polar transport, is a putative auxin efflux carrier. Neighbor-joining analysis using sequences deposited in NCBI databases showed that the PvPIN1gene belongs to the PIN1 family and is evolutionarily closer to the Oryza sativa japonica group. Tiller emergence and development was significantly promoted in plants subjected toPvPIN1 RNA interference (RNAi, which yielded a phenotype similar to that of wild-type plants treated with the auxin transport inhibitor TIBA (2,3,5-triiodobenzoic acid. A transgenic approach that inducedPvPIN1 gene overexpression or suppression altered tiller number and the shoot/root ratio. These data suggest that PvPIN1plays an important role in auxin-dependent adventitious root emergence and tillering.

  5. Identifying and Characterizing Impact Melt Outcrops in the Nectaris Basin

    Science.gov (United States)

    Cohen, B. A.; Lawerence, S. J.; Petro, N. E.; Bart, G. D.; Clegg-Watkins, R. N.; Denevi, B. W.; Ghent, R. R.; Klima, R. L.; Morgan, G. A.; Spudis, P. D.; Stopar, J. D.

    2016-01-01

    The Nectaris Basin is an 820-km diameter, multi-ring impact basin located on the near side of the Moon. Nectaris is a defining stratigraphic horizon based on relationships between ejecta units, giving its name to the Nectarian epoch of lunar history. Lunar basin chronology based on higher resolution LRO imagery and topography, while assigning some important basins like Serenitatis to pre-Nectarian time, were generally consistent with those previously derived. Based on this stratigraphy, at least 11 large basins formed in the time between Nectaris and Imbrium. The absolute age of Nectaris, therefore, is a crucial marker in the lunar time-stratigraphic sequence for understanding the impact flux on the Moon, and by extension, the entire inner solar system. For several decades, workers have attempted to constrain the age of the Nectaris basin through radiometric dating of lunar samples. However, there is little agreement on which samples in our collection represent Nectaris, if any, and what the correct radiometric age of such samples is. The importance of the age of Nectaris goes far beyond assigning a stratigraphic marker to lunar chronology. Several dynamical models use Nectaris as their pin date, so that this date becomes crucial in understanding the time-correlated effects in the rest of the solar system. The importance of the Nectaris basin age, coupled with its nearside, mid-latitude location, make remnants of the impact-melt sheet an attractive target for a future mission, either for in-situ dating or for sample return. We have started exploring this possibility. We have begun a consortium data-analysis effort bringing multiple datasets and analysis methods to bear on these putative impact-melt deposits to characterize their extent, elemental composition and mineralogy, maturity and geologic setting, and to identify potential landing sites that meet both operational safety and science requirements.

  6. An Analysis of the Equivalent Resistance of PIN Diodes at Microwave Frequencies

    Institute of Scientific and Technical Information of China (English)

    YANG Guo-yu; SONG Kai-jun; MAO Rui-jie; LU Shi-qiang

    2004-01-01

    The forward bias equivalent resistance of PIN diodes, an important parameter in applications, is usually measured at lower frequencies. But in fact, due to skin effect the effective conduction area of the region I of a PIN diode decreases as the frequency increases. In this paper, the affection of skin effect to forward bias equivalent resistance is considered and an analytic expression of the equivalent resistance of the region I is presented. In result, the forward bias resistance ora PIN diode at microwave frequencies is much higher than that at DC and low frequencies. It is necessary, therefore,to consider the skin effect of PIN diodes in high frequency applications.

  7. Design and fabrication of PIN-PMN-PT single-crystal high-frequency ultrasound transducers.

    Science.gov (United States)

    Sun, Ping; Zhou, Qifa; Zhu, Benpeng; Wu, Dawei; Hu, Changhong; Cannata, Jonathan M; Tian, Jin; Han, Pengdi; Wang, Gaofeng; Shung, K Kirk

    2009-12-01

    High-frequency PIN-PMN-PT single crystal ultrasound transducers at center frequencies of 35 MHz and 60 MHz were successfully fabricated using lead indium niobate-lead magnesium niobate-lead titanate (0.23PIN- 0.5PMN-0.27PT) single crystal. The new PIN-PMN-PT single crystal has higher coercivity (6.0 kV/cm) and higher Curie temperature (160 degrees C) than PMN-PT crystal. Experimental results showed that the PIN-PMN-PT transducers have similar performance but better thermal stability compared with the PMN-PT transducers.

  8. Design and Fabrication of PIN-PMN-PT Single-Crystal High-Frequency Ultrasound Transducers

    OpenAIRE

    Sun, Ping; Zhou, Qifa; Zhu, Benpeng; WU, DAWEI; Hu, Changhong; Cannata, Jonathan M.; Tian, Jin; Han, Pengdi; Wang, Gaofeng; Shung, K. Kirk

    2009-01-01

    High-frequency PIN-PMN-PT single crystal ultrasound transducers at center frequencies of 35 MHz and 60 MHz were successfully fabricated using lead indium niobate-lead magnesium niobate-lead titanate (0.23PIN-0.5PMN-0.27PT) single crystal. The new PIN-PMN-PT single crystal has higher coercivity (6.0 kV/cm) and higher Curie temperature (160°C) than PMN-PT crystal. Experimental results showed that the PIN-PMN-PT transducers have similar performance but better thermal stability compared with the ...

  9. Effects of Pin1 loss in HdhQ111 knock-in mice

    Directory of Open Access Journals (Sweden)

    Elena eAgostoni

    2016-05-01

    Full Text Available Huntington’s disease (HD is a fatal, dominantly inherited, neurodegenerative disorder due to a pathological expansion of the CAG repeat in the coding region of the HTT gene. In the quest for understanding the molecular basis of neurodegeneration, we have previously demonstrated that the prolyl isomerase Pin1 plays a crucial role in mediating p53-dependent apoptosis triggered by mutant huntingtin (mHtt in vitro. To assess the effects of the lack of Pin1 in vivo, we have bred Pin1 knock-out mice with HdhQ111 knock-in mice, a genetically precise model of HD. We show that Pin1 genetic ablation modifies a portion of HdhQ111 phenotypes in a time-dependent fashion. As an early event, Pin1 activity reduces the DNA damage response. In midlife mice, by taking advantage of next-generation sequencing technology, we show that Pin1 activity modulates a portion of the alterations triggered by mHtt, extending the role of Pin1 to two additional HdhQ111 phenotypes: the unbalance in the synthesis/concentration of hormones, as well as the alteration of Wnt/β-catenin signaling. In aging animals, Pin1 significantly increases the number of mHtt-positive nuclear inclusions while it reduces gliosis. In summary, this work provides further support for a role of Pin1 in HD pathogenesis.

  10. Functionally different PIN proteins control auxin flux during bulbil development in Agave tequilana.

    Science.gov (United States)

    Abraham Juárez, María Jazmín; Hernández Cárdenas, Rocío; Santoyo Villa, José Natzul; O'Connor, Devin; Sluis, Aaron; Hake, Sarah; Ordaz-Ortiz, José; Terry, Leon; Simpson, June

    2015-07-01

    In Agave tequilana, reproductive failure or inadequate flower development stimulates the formation of vegetative bulbils at the bracteoles, ensuring survival in a hostile environment. Little is known about the signals that trigger this probably unique phenomenon in agave species. Here we report that auxin plays a central role in bulbil development and show that the localization of PIN1-related proteins is consistent with altered auxin transport during this process. Analysis of agave transcriptome data led to the identification of the A. tequilana orthologue of PIN1 (denoted AtqPIN1) and a second closely related gene from a distinct clade reported as 'Sister of PIN1' (denoted AtqSoPIN1). Quantitative real-time reverse transcription-PCR (RT-qPCR) analysis showed different patterns of expression for each gene during bulbil formation, and heterologous expression of the A. tequilana PIN1 and SoPIN1 genes in Arabidopsis thaliana confirmed functional differences between these genes. Although no free auxin was detected in induced pedicel samples, changes in the levels of auxin precursors were observed. Taken as a whole, the data support the model that AtqPIN1 and AtqSoPIN1 have co-ordinated but distinct functions in relation to auxin transport during the initial stages of bulbil formation.

  11. Phylogeny and molecular evolution analysis of PIN-FORMED 1 in angiosperm.

    Directory of Open Access Journals (Sweden)

    Pengkai Wang

    Full Text Available PIN-FORMED 1 (PIN1 is an important secondary transporter and determines the direction of intercellular auxin flow. As PIN1 performs the conserved function of auxin transport, it is expected that the sequence and structure of PIN1 is conserved. Therefore, we hypothesized that PIN1 evolve under pervasive purifying selection in the protein-coding sequences in angiosperm. To test this hypothesis, we performed detailed evolutionary analyses of 67 PIN1 sequences from 35 angiosperm species. We found that the PIN1 sequences are highly conserved within their transmembrane regions, part of their hydrophilic regions. We also found that there are two or more PIN1 copies in some of these angiosperm species. PIN1 sequences from Poaceae and Brassicaceae are representative of the modern clade. We identified 12 highly conserved motifs and a significant number of family-specific sites within these motifs. One family-specific site within Motif 11 shows a different residue between monocots and dicots, and is functionally critical for the polarity of PIN1. Likewise, the function of PIN1 appears to be different between monocots and dicots since the phenotype associated with PIN1 overexpression is opposite between Arabidopsis and rice. The evolution of angiosperm PIN1 protein-coding sequences appears to have been primarily driven by purifying selection, but traces of positive selection associated with sequences from certain families also seem to be present. We verified this observation by calculating the numbers of non-synonymous and synonymous changes on each branch of a phylogenetic tree. Our results indicate that the evolution of angiosperm PIN1 sequences involve strong purifying selection. In addition, our results suggest that the conserved sequences of PIN1 derive from a combination of the family-specific site variations and conserved motifs during their unique evolutionary processes, which is critical for the functional integrity and stability of these auxin

  12. Flavonoids Redirect PIN-mediated Polar Auxin Fluxes during Root Gravitropic Responses*S⃞

    Science.gov (United States)

    Santelia, Diana; Henrichs, Sina; Vincenzetti, Vincent; Sauer, Michael; Bigler, Laurent; Klein, Markus; Bailly, Aurélien; Lee, Youngsook; Friml, Jir̆í; Geisler, Markus; Martinoia, Enrico

    2008-01-01

    The rate, polarity, and symmetry of the flow of the plant hormone auxin are determined by the polar cellular localization of PIN-FORMED (PIN) auxin efflux carriers. Flavonoids, a class of secondary plant metabolites, have been suspected to modulate auxin transport and tropic responses. Nevertheless, the identity of specific flavonoid compounds involved and their molecular function and targets in vivo are essentially unknown. Here we show that the root elongation zone of agravitropic pin2/eir1/wav6/agr1 has an altered pattern and amount of flavonol glycosides. Application of nanomolar concentrations of flavonols to pin2 roots is sufficient to partially restore root gravitropism. By employing a quantitative cell biological approach, we demonstrate that flavonoids partially restore the formation of lateral auxin gradients in the absence of PIN2. Chemical complementation by flavonoids correlates with an asymmetric distribution of the PIN1 protein. pin2 complementation probably does not result from inhibition of auxin efflux, as supply of the auxin transport inhibitor N-1-naphthylphthalamic acid failed to restore pin2 gravitropism. We propose that flavonoids promote asymmetric PIN shifts during gravity stimulation, thus redirecting basipetal auxin streams necessary for root bending. PMID:18718912

  13. Controlling flux flow dissipation by changing flux pinning in superconducting films

    Energy Technology Data Exchange (ETDEWEB)

    Grimaldi, G.; Leo, A.; Nigro, A.; Pace, S. [CNR SPIN Salerno and Dipartimento di Fisica ' ' E. R. Caianiello' ' , Universita degli Studi di Salerno, via Ponte Don Melillo, 84084 Fisciano (Italy); Silhanek, A. V. [Department de Physique, Universite de Liege, B-4000 Sart Tilman (Belgium); INPAC-Institute for Nanoscale Physics and Chemistry, Nanoscale Superconductivity and Magnetism Group, K. U. Leuven, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Verellen, N.; Moshchalkov, V. V. [INPAC-Institute for Nanoscale Physics and Chemistry, Nanoscale Superconductivity and Magnetism Group, K. U. Leuven, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Milosevic, M. V. [Departement Fysica, Universiteit Antwerpen, Groenenborgerlaan 171, B-2020 Antwerpen (Belgium); Casaburi, A.; Cristiano, R. [Istituto di Cibernetica ' ' E. Caianiello' ' , CNR, 80078 Pozzuoli (Italy)

    2012-05-14

    We study the flux flow state in superconducting materials characterized by rather strong intrinsic pinning, such as Nb, NbN, and nanostructured Al thin films, in which we drag the superconducting dissipative state into the normal state by current biasing. We modify the vortex pinning strength either by ion irradiation, by tuning the measuring temperature or by including artificial pinning centers. We measure critical flux flow voltages for all materials and the same effect is observed: switching to low flux flow dissipations at low fields for an intermediate pinning regime. This mechanism offers a way to additionally promote the stability of the superconducting state.

  14. Controlled pinning and depinning of domain walls in nanowires with perpendicular magnetic anisotropy.

    Science.gov (United States)

    Gerhardt, Theo; Drews, André; Meier, Guido

    2012-01-18

    We investigate switching and field-driven domain wall motion in nanowires with perpendicular magnetic anisotropy comprising local modifications of the material parameters. Intentional nucleation and pinning sites with various geometries inside the nanowires are realized via a local reduction of the anisotropy constant. Micromagnetic simulations and analytical calculations are employed to determine the switching fields and to characterize the pinning potentials and the depinning fields. Nucleation sites in the simulations cause a significant reduction of the switching field and are in excellent agreement with analytical calculations. Pinning potentials and depinning fields caused by the pinning sites strongly depend on their shapes and are well explained by analytical calculations.

  15. Enquiry into the Topology of Plasma Membrane-Localized PIN Auxin Transport Components.

    Science.gov (United States)

    Nodzyński, Tomasz; Vanneste, Steffen; Zwiewka, Marta; Pernisová, Markéta; Hejátko, Jan; Friml, Jiří

    2016-11-07

    Auxin directs plant ontogenesis via differential accumulation within tissues depending largely on the activity of PIN proteins that mediate auxin efflux from cells and its directional cell-to-cell transport. Regardless of the developmental importance of PINs, the structure of these transporters is poorly characterized. Here, we present experimental data concerning protein topology of plasma membrane-localized PINs. Utilizing approaches based on pH-dependent quenching of fluorescent reporters combined with immunolocalization techniques, we mapped the membrane topology of PINs and further cross-validated our results using available topology modeling software. We delineated the topology of PIN1 with two transmembrane (TM) bundles of five α-helices linked by a large intracellular loop and a C-terminus positioned outside the cytoplasm. Using constraints derived from our experimental data, we also provide an updated position of helical regions generating a verisimilitude model of PIN1. Since the canonical long PINs show a high degree of conservation in TM domains and auxin transport capacity has been demonstrated for Arabidopsis representatives of this group, this empirically enhanced topological model of PIN1 will be an important starting point for further studies on PIN structure-function relationships. In addition, we have established protocols that can be used to probe the topology of other plasma membrane proteins in plants.

  16. Reduced energy consumption for melting in foundries

    Energy Technology Data Exchange (ETDEWEB)

    Skov-Hansen, S.

    2007-09-15

    representative results of how the melt flows in a real mould a series of experiments have been conducted using the xray facilities at the Metallurgy and Materials department at the University of Birmingham. The results proved that the glass plate do not have any large effect on the flow pattern during mould filling. It was also found that using fan gates only 1mm thick holds back slag and in this way works as a filter. A complete set of guidelines for designing streamlined gating systems have been made in this project. Using these guidelines and combining standard geometries and the presented spreadsheet makes it possible for foundries to use streamlined gating systems in praxis. (au)

  17. Development of melt dilute technology for disposition of aluminum based spent nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Swift, W.F. [Nuclear Material Management Division Westinghouse Savannah River Company, Savannah River Site Building 707-C, Aiken, SC 29808 (United States)

    2002-07-01

    The US Department of Energy (DOE) has for many years had a program for receipt and disposition of spent nuclear fuels of US origin from research reactors around the world. The research reactor spent nuclear fuel that consists of aluminum alloy composition has historically been returned to the Savannah River Site (SRS) and dispositioned via chemical reprocessing. In 1995, the DOE evaluated a number of alternatives to chemical reprocessing. In 2000, the DOE selected the melt-dilute alternative as the primary disposition path and direct disposal as the backup path. The melt-dilute technology has been developed from lab-scale demonstration up through the construction of a pilot-scale facility. The pilot-scale L-Area Experimental Facility (LEF) has been constructed and is ready for operation. The LEF will be used primarily, to confirm laboratory research on zeolite media for off- gas trapping and remote operability. Favorable results from the LEF are expected to lead to final design of the production melt-dilute facility identified as the Treatment and Storage Facility (TSF). This paper will describe the melt-dilute process and provide a status of the program development. (author)

  18. Silicon P.I.N. Junctions used for studies of radiation damage; Etude de l'irradiation aux neutrons rapides du silicium au moyen de jonctions P.I.N

    Energy Technology Data Exchange (ETDEWEB)

    Lanore, J. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-06-01

    Irradiation of silicon P.I.N. junction has been studied primarily for the purpose of developing a radiation damage dosimeter, but also for the purpose of investigating silicon itself. It is known that the rate of recombination of electrons and holes is a linear function of defects introduced by neutron irradiation. Two methods have been used to measure that rate of recombination: forward characteristic measurements, recovery time measurements. In order to explain how these two parameters depend on recombination rate we have given a theory of the P.I.N. junction. We have also given an idea of the carrier lifetime dependence versus temperature. Annealing effects in the range of 70 to 700 K have also been studied, we found five annealing stages with corresponding activation energies. As an application for these studies, we developed a radiation damage dosimeter with which we made several experiments in facilities such as Naiade or Marias. (author) [French] L'irradiation de structures P.I.N. etait faite dans le but d'etudier principalement la mise au point d'un dosimetre a ''radiation damage'' et aussi pour etudier plus profondement le silicium lui-meme. On sait que le taux de recombinaison electrons-trous est une fonction lineaire du taux de defauts introduits par irradiation aux neutrons. Deux methodes ont ete utilisees pour atteindre ce taux de recombinaison: mesures de la caracteristique directe, mesures du temps de retournement. Pour expliquer de quelle facon ces parametres dependent du taux de recombinaison. Nous avons donne une theorie de la jonction P.I.N. Nous avons aussi donne l'allure des variations du temps de vie des porteurs en fonction de la temperature. Nous avons d'autre part effectue des recuits entre 70 et 700 K, domaine dans lequel nous avons trouve cinq etapes de ''guerison'' avec les energies d'activation correspondantes. En application de ces etudes nous avons mis ou point un

  19. The Half-Pin and the Pin Tract: A Survey of the Limb Lengthening and Reconstruction Society

    Science.gov (United States)

    2013-09-01

    report no actual or potential conflict of interest in relation to this article. AJO DO NOT COPY Report Documentation Page Form ApprovedOMB No. 0704-0188...dealing with half-pin scars? 9. Do you remove frames in the operating room or clinic? AJO DO NOT COPY E70    The American Journal of Orthopedics...open-ended question soliciting comments and tips/tricks not addressed in the 9-question survey (Table I). AJO DO NOT COPY A Survey of the Limb

  20. Measurement strategy and analytic model to determine firing pin force

    Science.gov (United States)

    Lesenciuc, Ioan; Suciu, Cornel

    2016-12-01

    As illustrated in literature, ballistics is a branch of theoretical mechanics, which studies the construction and working principles of firearms and ammunition, their effects, as well as the motions of projectiles and bullets1. Criminalistics identification, as part of judiciary identification represents an activity aimed at finding common traits of different objects, objectives, phenomena and beings, but more importantly, traits that differentiate each of them from similar ones2-4. In judicial ballistics, in the case of rifled firearms it is relatively simple for experts to identify the used weapon from traces left on the projectile, as the rifling of the barrel leaves imprints on the bullet, which remain approximately identical even after the respective weapon is fired 100 times with the same barrel. However, in the case of smoothbore firearms, their identification becomes much more complicated. As the firing cap suffers alterations from being hit by the firing pin, determination of the force generated during impact creates the premises for determining the type of firearm used to shoot the respective cartridge. The present paper proposes a simple impact model that can be used to evaluate the force generated by the firing pin during its impact with the firing cap. The present research clearly showed that each rifle, by the combination of the three investigated parameters (impact force maximum value, its variation diagram, and impact time) leave a unique trace. Application of such a method in ballistics can create the perspectives for formulating clear conclusions that eliminate possible judicial errors in this field.

  1. Optimal pinning controllability of complex networks: dependence on network structure.

    Science.gov (United States)

    Jalili, Mahdi; Askari Sichani, Omid; Yu, Xinghuo

    2015-01-01

    Controlling networked structures has many applications in science and engineering. In this paper, we consider the problem of pinning control (pinning the dynamics into the reference state), and optimally placing the driver nodes, i.e., the nodes to which the control signal is fed. Considering the local controllability concept, a metric based on the eigenvalues of the Laplacian matrix is taken into account as a measure of controllability. We show that the proposed optimal placement strategy considerably outperforms heuristic methods including choosing hub nodes with high degree or betweenness centrality as drivers. We also study properties of optimal drivers in terms of various centrality measures including degree, betweenness, closeness, and clustering coefficient. The profile of these centrality values depends on the network structure. For homogeneous networks such as random small-world networks, the optimal driver nodes have almost the mean centrality value of the population (much lower than the centrality value of hub nodes), whereas the centrality value of optimal drivers in heterogeneous networks such as scale-free ones is much higher than the average and close to that of hub nodes. However, as the degree of heterogeneity decreases in such networks, the profile of centrality approaches the population mean.

  2. Characterization of Nb-Ti superconductors with artificial pinning structures

    Energy Technology Data Exchange (ETDEWEB)

    Dietderich, D.R.; Scanlan, R.M.

    1990-06-01

    A series of multifilamentary APC Nb-Ti superconductors have been made with Nb added as a normal second phase to provide flux pinning centers. Two compositions, 12.5% vol % and 25 vol % Nb in Nb-Ti, have fabricated into multifilamentary composites using two different fabrication methods. One method used hot isostatic compaction and hot extrusion thoughout the processing. The other method (bundle-and-draw process) discontinued all hot processing at an intermediate level. While the J{sub c} values of the bundle-and-draw wires are quite promising, the critical current of the extruded wires appears to be limited by poor uniformity of the filament cross-sectional area along the conductor length. The large values of the index of the resistive transition and small filament standard-deviation-to-average area ratios observed in the wires produced by the bundle-and-draw process suggest extrinsic factors have little effect on J{sub c}. The variation in J{sub c} as the wire diameter is reduced appears to be most strongly affected by intrinsic factors: Nb distribution and pinning strength. The final filament microstructure and Nb spacing are shown to be difficult to calculate, e.g., the mean Nb spacing near the final wire size may be {1/2} to 1/3 that of the calculated value. 5 refs., 5 figs.

  3. Modeling the Interaction between AFM Tips and Pinned Surface Nanobubbles.

    Science.gov (United States)

    Guo, Zhenjiang; Liu, Yawei; Xiao, Qianxiang; Schönherr, Holger; Zhang, Xianren

    2016-01-26

    Although the morphology of surface nanobubbles has been studied widely with different AFM modes, AFM images may not reflect the real shapes of the nanobubbles due to AFM tip-nanobubble interactions. In addition, the interplay between surface nanobubble deformation and induced capillary force has not been well understood in this context. In our work we used constraint lattice density functional theory to investigate the interaction between AFM tips and pinned surface nanobubbles systematically, especially concentrating on the effects of tip hydrophilicity and shape. For a hydrophilic tip contacting a nanobubble, its hydrophilic nature facilitates its departure from the bubble surface, displaying a weak and intermediate-range attraction. However, when the tip squeezes the nanobubble during the approach process, the nanobubble shows an elastic effect that prevents the tip from penetrating the bubble, leading to a strong nanobubble deformation and repulsive interactions. On the contrary, a hydrophobic tip can easily pierce the vapor-liquid interface of the nanobubble during the approach process, leading to the disappearance of the repulsive force. In the retraction process, however, the adhesion between the tip and the nanobubble leads to a much stronger lengthening effect on nanobubble deformation and a strong long-range attractive force. The trends of force evolution from our simulations agree qualitatively well with recent experimental AFM observations. This favorable agreement demonstrates that our model catches the main intergradient of tip-nanobubble interactions for pinned surface nanobubbles and may therefore provide important insight into how to design minimally invasive AFM experiments.

  4. Flux-Vortex Pinning and Neutron Star Evolution

    Science.gov (United States)

    Alpar, M. Ali

    2017-09-01

    G. Srinivasan et al. (1990) proposed a simple and elegant explanation for the reduction of the neutron star magnetic dipole moment during binary evolution leading to low mass X-ray binaries and eventually to millisecond pulsars: Quantized vortex lines in the neutron star core superfluid will pin against the quantized flux lines of the proton superconductor. As the neutron star spins down in the wind accretion phase of binary evolution, outward motion of vortex lines will reduce the dipole magnetic moment in proportion to the rotation rate. The presence of a toroidal array of flux lines makes this mechanism inevitable and independent of the angle between the rotation and magnetic axes. The incompressibility of the flux-line array (Abrikosov lattice) determines the epoch when the mechanism will be effective throughout the neutron star. Flux vortex pinning will not be effective during the initial young radio pulsar phase. It will, however, be effective and reduce the dipole moment in proportion with the rotation rate during the epoch of spindown by wind accretion as proposed by Srinivasan et al. The mechanism operates also in the presence of vortex creep.

  5. Raman spectroscopy of PIN hydrogenated amorphous silicon solar cells

    Science.gov (United States)

    Keya, Kimitaka; Torigoe, Yoshihiro; Toko, Susumu; Yamashita, Daisuke; Seo, Hyunwoong; Itagaki, Naho; Koga, Kazunori; Shiratani, Masaharu

    2015-09-01

    Light-induced degradation of hydrogenated amorphous silicon (a-Si:H) is a key issue for enhancing competitiveness in solar cell market. A-Si:H films with a lower density of Si-H2 bonds shows higher stability. Here we identified Si-H2 bonds in PIN a-Si:H solar cells fabricated by plasma CVD using Raman spectroscopy. A-Si:H solar cell has a structure of B-doped μc-SiC:H (12.5 nm)/ non-doped a-Si:H (250nm)/ P-doped μc-Si:H (40 nm) on glass substrates (Asahi-VU). By irradiating HeNe laser light from N-layer, peaks correspond to Si-H2 bonds (2100 cm-1) and Si-H bonds (2000 cm-1) have been identified in Raman scattering spectra. The intensity ratio of Si-H2 and Si-H ISiH2/ISiH is found to correlate well to light induced degradation of the cells Therefore, Raman spectroscopy is a promising method for studying origin of light-induced degradation of PIN solar cells.

  6. Electrical detection of spin coherence in microcrystalline pin solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Behrends, Jan [Hahn-Meitner-Institut Berlin, Abt. Silizium-Photovoltaik, Berlin (Germany); Department of Physics, University of Utah, Salt Lake City, UT (United States); Boehme, Christoph; Lips, Klaus [Hahn-Meitner-Institut Berlin, Abt. Silizium-Photovoltaik, Berlin (Germany); Haas, Stefan [Institute of Photovoltaics, Forschungszentrum Juelich, Juelich (Germany); Rech, Bernd [Hahn-Meitner-Institut Berlin, Abt. Silizium-Photovoltaik, Berlin (Germany); Institute of Photovoltaics, Forschungszentrum Juelich, Juelich (Germany)

    2007-07-01

    Defects in the band gap of hydrogenated microcrystalline silicon ({mu}cSi:H) pin solar cells, even at low concentrations, can act as recombination centres and thus, they can influence the electronic properties of the device significantly. A powerful technique to investigate these recombination processes is pulsed electrically detected magnetic resonance (pEDMR). This method is based on transient photocurrent measurements after varying specific recombination or transport rates and reveals information about the microscopic mechanisms of recombination and transport that involve paramagnetic states. In this study we report on the application of pEDMR on state-of-the-art {mu}c-Si:H pin solar cells prepared on ZnO coated glass. An adapted contact structure allows the observation of Rabi oscillations in the photocurrent at low temperatures (T=10 K) reflecting coherent spin motion. The coherence time is found to be on the order of several hundred nanoseconds and is determined by recombination. A Fourier analysis of the observed Rabi oscillations allows a distinction between the involved recombination processes. A discussion on the different recombination mechanisms in {mu}c-Si:H cells is given.

  7. Strength of self-pinning in coffee drops

    Science.gov (United States)

    Latka, Andrzej; Kawczinski, Kimberly; Nagel, Sidney

    The equilibrium contact angle θe of a liquid drop placed on a solid surface is uniquely determined by a balance of surface tension forces according to Young's Equation, yet is rarely observed in real systems. Due to contact angle hysteresis, liquids can make contact with a surface at any angle between the receding and advancing contact angle: θR coffee stain. For coffee θR = 0 , thus as the drop evaporates the contact line remains pinned at its initial location. This results in the majority of the coffee being deposited in a characteristic ring at the drop's original boundary. We investigate how solid particles suspended in a liquid could so strongly influence contact angle hysteresis, by measuring the receding contact angle of a drop at various times during the evaporation process. For low solute concentrations, θR slowly decreases as the drop evaporates, but remains positive. Surprisingly, we find that increasing the solute concentration results in θR = 0 and a fully pinned contact line almost immediately after the drop is deposited.

  8. Temperature dependent simulation of diamond depleted Schottky PIN diodes

    Science.gov (United States)

    Hathwar, Raghuraj; Dutta, Maitreya; Koeck, Franz A. M.; Nemanich, Robert J.; Chowdhury, Srabanti; Goodnick, Stephen M.

    2016-06-01

    Diamond is considered as an ideal material for high field and high power devices due to its high breakdown field, high lightly doped carrier mobility, and high thermal conductivity. The modeling and simulation of diamond devices are therefore important to predict the performances of diamond based devices. In this context, we use Silvaco® Atlas, a drift-diffusion based commercial software, to model diamond based power devices. The models used in Atlas were modified to account for both variable range and nearest neighbor hopping transport in the impurity bands associated with high activation energies for boron doped and phosphorus doped diamond. The models were fit to experimentally reported resistivity data over a wide range of doping concentrations and temperatures. We compare to recent data on depleted diamond Schottky PIN diodes demonstrating low turn-on voltages and high reverse breakdown voltages, which could be useful for high power rectifying applications due to the low turn-on voltage enabling high forward current densities. Three dimensional simulations of the depleted Schottky PIN diamond devices were performed and the results are verified with experimental data at different operating temperatures

  9. Tungsten disrupts root growth in Arabidopsis thaliana by PIN targeting.

    Science.gov (United States)

    Adamakis, Ioannis-Dimosthenis S; Panteris, Emmanuel; Eleftheriou, Eleftherios P

    2014-08-15

    Tungsten is a heavy metal with increasing concern over its environmental impact. In plants it is extensively used to deplete nitric oxide by inhibiting nitrate reductase, but its presumed toxicity as a heavy metal has been less explored. Accordingly, its effects on Arabidopsis thaliana primary root were assessed. The effects on root growth, mitotic cell percentage, nitric oxide and hydrogen peroxide levels, the cytoskeleton, cell ultrastructure, auxin and cytokinin activity, and auxin carrier distribution were investigated. It was found that tungsten reduced root growth, particularly by inhibiting cell expansion in the elongation zone, so that root hairs emerged closer to the root tip than in the control. Although extensive vacuolation was observed, even in meristematic cells, cell organelles were almost unaffected and microtubules were not depolymerized but reoriented. Tungsten affected auxin and cytokinin activity, as visualized by the DR5-GFP and TCS-GFP expressing lines, respectively. Cytokinin fluctuations were similar to those of the mitotic cell percentage. DR5-GFP signal appeared ectopically expressed, while the signals of PIN2-GFP and PIN3-GFP were diminished even after relatively short exposures. The observed effects were not reminiscent of those of any nitric oxide scavengers. Taken together, inhibition of root growth by tungsten might rather be related to a presumed interference with the basipetal flow of auxin, specifically affecting cell expansion in the elongation zone.

  10. Fuel Storage Facility Final Safety Analysis Report. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Linderoth, C.E.

    1984-03-01

    The Fuel Storage Facility (FSF) is an integral part of the Fast Flux Test Facility. Its purpose is to provide long-term storage (20-year design life) for spent fuel core elements used to provide the fast flux environment in FFTF, and for test fuel pins, components and subassemblies that have been irradiated in the fast flux environment. This Final Safety Analysis Report (FSAR) and its supporting documentation provides a complete description and safety evaluation of the site, the plant design, operations, and potential accidents.

  11. Melt water interaction tests. PREMIX tests PM10 and PM11

    Energy Technology Data Exchange (ETDEWEB)

    Kaiser, A.; Schuetz, W.; Will, H. [Forschungszentrum Karlsruhe Inst. fuer Reaktorsicherheit, Karlsruhe (Germany)

    1998-01-01

    A series of experiments is being performed in the PREMIX test facility in which the mixing behaviour is investigated of a hot alumina melt discharged into water. The major parameters have been: the melt mass, the number of nozzles, the distance between the nozzle and the water, and the depth of the water. The paper describes the last two tests in which 20 kg of melt were released through one and three nozzles, respectively, directly into the water whose depth was 500 mm. The melt penetration and the associated phenomena of mixing are described by means of high-speed films and various measurements. The steam production and, subsequently, the pressure increased markedly only after the melt had reached the bottom of the pool. Spreading of the melt across the bottom caused violent boiling in both tests. Whereas the boiling lasted for minutes in the single-jet test, a steam explosion occurred in the triple-jet test about one second after the start of melt penetration. (author)

  12. The kinetics of root gravitropism in PIN mutants suggest redundancy in the signal transduction pathway

    Science.gov (United States)

    Wolverton, Chris

    As nonmotile organisms, plants rely on differential growth responses to maximize exposure to the resources necessary for growth and reproduction. One of the primary environmental cues causing differential growth in roots is gravity, which is thought to be sensed predominately in the root cap. This gravity perception event is thought to be transduced into information in the form of an auxin gradient across the cap and propagating basipetally toward the elongation zone. The discovery of several families of auxin efflux and influx carriers has provided significant insight into the mechanisms of directional auxin transport, and the identification of mutants in the genes encoding these carriers provides the opportunity to test the roles of these transporters in plant gravitropism. In this study, we report the results of a systematic, high-resolution study of the kinetics of root gravitropism of mutants in the PIN family of auxin efflux carriers. Based on reported expression and localization patterns, we predicted mutations in PIN2, PIN3, PIN4, and PIN7 to cause the greatest reduction in root gravitropism. While pin2 mutants showed severe gravitropic deficiencies in roots as reported previously, several alleles of pin3, pin4 and pin7 remained strongly gravitropic. PIN3 has been localized to the central columella cells, the purported gravisensing cells in the root, and shown to rapidly relocate to the lower flank of the columella cells upon gravistimulation, suggesting an early role in auxin gradient formation. Mutant alleles of PIN3 showed an early delay in response, with just 7 deg of curvature in the first hour compared to approximately 15 deg h-1 in wild-type, but their rate of curvature recovered to near wild-type levels over the ensuing 3 h. Pin3 mutants also showed a slower overall growth rate (124 µm h-1 ), elongating at approximately half the rate of wild-type roots (240 µm h-1 ). PIN4 has been localized to the quiescent center in the root, where it presumably

  13. Melting of heterogeneous vortex matter: The vortex `nanoliquid'

    Indian Academy of Sciences (India)

    S S Banerjee; S Goldberg; Y Myasoedov; M Rappaport; E Zeldov; A Soibel; F de la Cruz; C J van der Beek; M Konczykowski; T Tamegai; V Vinokur

    2006-01-01

    Disorder and porosity are parameters that strongly influence the physical behavior of materials, including their mechanical, electrical, magnetic and optical properties. Vortices in superconductors can provide important insight into the effects of disorder because their size is comparable to characteristic sizes of nanofabricated structures. Here we present experimental evidence for a novel form of vortex matter that consists of inter-connected nanodroplets of vortex liquid caged in the pores of a solid vortex structure, like a liquid permeated into a nanoporous solid skeleton. Our nanoporous skeleton is formed by vortices pinned by correlated disorder created by high-energy heavy ion irradiation. By sweeping the applied magnetic field, the number of vortices in the nanodroplets is varied continuously from a few to several hundred. Upon cooling, the caged nanodroplets freeze into ordered nanocrystals through either a first-order or a continuous transition, whereas at high temperatures a uniform liquid phase is formed upon delocalization-induced melt- ing of the solid skeleton. This new vortex nanoliquid displays unique properties and symmetries that are distinct from both solid and liquid phases.

  14. Emission Facilities - Erosion & Sediment Control Facilities

    Data.gov (United States)

    NSGIC Education | GIS Inventory — An Erosion and Sediment Control Facility is a DEP primary facility type related to the Water Pollution Control program. The following sub-facility types related to...

  15. Rotation of melting ice disks due to melt fluid flow.

    Science.gov (United States)

    Dorbolo, S; Adami, N; Dubois, C; Caps, H; Vandewalle, N; Darbois-Texier, B

    2016-03-01

    We report experiments concerning the melting of ice disks (85 mm in diameter and 14 mm in height) at the surface of a thermalized water bath. During the melting, the ice disks undergo translational and rotational motions. In particular, the disks rotate. The rotation speed has been found to increase with the bath temperature. We investigated the flow under the bottom face of the ice disks by a particle image velocimetry technique. We find that the flow goes downwards and also rotates horizontally, so that a vertical vortex is generated under the ice disk. The proposed mechanism is the following. In the vicinity of the bottom face of the disk, the water eventually reaches the temperature of 4 °C for which the water density is maximum. The 4 °C water sinks and generates a downwards plume. The observed vertical vorticity results from the flow in the plume. Finally, by viscous entrainment, the horizontal rotation of the flow induces the solid rotation of the ice block. This mechanism seems generic: any vertical flow that generates a vortex will induce the rotation of a floating object.

  16. Sensitive pre-amplifier to load for Pin diodes; Pre-amplificador sensible a carga para diodos PIN

    Energy Technology Data Exchange (ETDEWEB)

    Jacobo V, R. Y.; Hernandez D, V. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98060 Zacatecas (Mexico); Ramirez J, F. J., E-mail: yoshimarv@gmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2013-10-15

    The electronic instrumentation is indispensable for the measurement and characterization of the radiation. By means of this essential characteristics of the radiation are determined, as activity and their energy components. The nuclear instrumentation is based on the technical characteristics of the radiation detectors and the electronic devices associates (amplifiers, ana logical and digital converters, multichannel analyzers, etc.) The radiation detectors are very important instruments in fields as the nuclear physics, medicine, radiological protection, industry and in other fields, since they are the only method to capture the radiation and to be able to quantify it in precise form. To detect radiation diverse detector types are used, as the semiconductor type, inside them are the photodiodes type Pin. In this work the results that were obtained of the design, simulation, construction and tests of a preamplifier that was designed starting from a photodiode type Pin are presented. The system was designed and simulated with a program for electronic circuits, in this were carried out many tests being obtained a compact design and achieving the best necessary characteristics for its optimization. With the results of the simulation phase the electronics phase was built, which was couples to a spectroscopic amplifier and a multichannel analyzer. The total of the system was evaluated analyzing its performance before a triple source of alphas. Of the tests phase we find that the system allows obtaining, in a multichannel analyzer, the pulses height spectrum, with a good resolution and with this was calibrated the multichannel analyzer.

  17. Effect of melting conditions on striae in iron-bearing silicate melts

    DEFF Research Database (Denmark)

    Jensen, Martin; Yue, Yuanzheng

    2012-01-01

    Chemical striae are present in a broad range of glass products, but due to their negative impact on e.g., the optical and mechanical properties, elimination of striae from melts is a key issue in glass technology. By varying melting temperatures, retentions times and redox conditions of an iron......-bearing calciumaluminosilicate melt, we quantify the effect of each of the three melting parameters on the stria content in the melt. The quantification of the stria content in the melt is conducted by means of image analysis on casted melt samples. We find that in comparison to an extension of retention time an increase...... factors such as compositional fluctuation of melts and bubbling due to iron reduction on the stria content. During the melting process, striae with a chemical gradient in a more mobile species equilibrate faster than striae caused by a chemical gradient in a less mobile species. The temperature and time...

  18. Deterministic Analysis of a Beyond Design Basis Accident in a Low Power, Pin-Type Fuel Research Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Nagah Abdou, Hesham Mohammed [INVAP S. E., Bariloche (Argentina)

    2013-07-01

    A Beyond Design Basis Accident has been analyzed for a pool type research reactor with pin-type, Zry4 clad fuel. This is a low power research reactor (maximum power: 100kW) with neutron beam facilities. Two scenarios are considered: a neutron beam rapture that results in a fraction of the core submerged in water and a catastrophic failure that results in a fully uncovered core. The paper discusses the different cooling mechanisms for these two BDBAs and compares results for both scenarios, with predictions of no core damage in any situation. Core damage is defined as CHFR↔1.5 and/or Tclad→T start of breakaway oxidation temperature. In addition, the paper compares calculations with a thermalhydraulic code and an analytical model. This paper allows to analyze the applicability of regular thermalhydraulic codes to BDBA accident scenarios in low power research reactors.

  19. Heat transfer and pressure drop in a compact pin-fin heat exchanger with pin orientation at 18 deg to the flow direction

    Science.gov (United States)

    Olson, D. A.

    1991-01-01

    The heat transfer and pressure drop characteristics of a novel, compact heat exchanger in helium gas were measured at 3.5 MPa and Reynolds numbers of 450 to 12,000. The pin-fin specimen consisted of pins, 0.51 mm high and spaced 2.03 mm on centers, spanning a channel through which the helium flows; the angle of the row of pins to the flow direction was 18 deg. The specimen was radiatively heated on the top side at heat fluxes up to 74 W/sq cm and insulated on the back side. Correlations were developed for the friction factor and Nusselt number. The Nusselt number compares favorably to those of past studies of staggered pin-fins, when the measured temperatures are extrapolated to the temperature of the wall-fluid interface.

  20. Aluminium toxicity targets PIN2 in Arabidopsis root apices: Effects on PIN2 endocytosis, vesicular recycling,and polar auxin transport

    Institute of Scientific and Technical Information of China (English)

    SHEN Hong; HOU NingYan; Markus SCHLICHT; WAN YingLang; Stefano MANCUSO; Frantisek BALUSKA

    2008-01-01

    The most obvious symptom of AI toxicity is the inhibition of root growth.However,the mechanism of AI-inhibiting root growth remains to be elucidated.In this study,auxin transport and vesicle movement of an auxin-efflux carrier (PIN2) were investigated in Arabidopsis roots in response to AI stress.Results indicated that AI inhibited the apical transport of auxin in root tips of Arabidopsis significantly.The severe inhibition was localized in the cells of transition zone,where the concentration of auxin was only 34% that of the control.Brefeldin A (BFA),an inhibitor of vesicle transport,induced the dot-like structure of PIN2 vesicle significantly.Al decreased the size of dot-like structure of PIN2 vesicles.Re-sults of real-time RT-PCR and Western-blotting analysis showed that Al increased the transcript level of PIN2 and the accumulation of PIN2 protein in horizontal direction of plasma membrane,but decreased its distribution in endosomes,suggesting that AI inhibited the transport of PIN2 vesicles from plasma membrane to endosomes.Results of cytoskeleton-depolymering drugs indicated that it was via the pathway of disruption of actin microfilaments that AI inhibited the transport of PIN2 vesicles.Exposed to AI stress,the cells of elongation zone had less AI uptake and less transport frequency of vesicles than cells of transition zone.Taken together,our results suggested that AI inhibited root growth mainly by modulating the transport of PIN2 vesicles between plasma membrane and endosomes,thus block-ing auxin transport and root growth.

  1. Using the Missing Pin to Challenge Concepts of Refraction and Total Internal Reflection

    Science.gov (United States)

    Tamang, Sushmika; Nopparatjamjomras, Suchai; Chitaree, Ratchapak; Nopparatjamjomras, Thasaneeya R.

    2015-01-01

    A container was placed on top of a piece of white paper, and a pin positioned so that it vertically touched an outside wall of the container. Students were asked to predict the image of the pin when it was observed from the top of the container. Two scenarios of either an empty container or a container completely filled with water were considered…

  2. Experimental adiabatic vortex ratchet effect in Nb films with asymmetric pinning trap

    Indian Academy of Sciences (India)

    J E Villegas; N O nunez; M P Gonzalez; E M Gonalez; J L Vicent

    2006-01-01

    Nb films grown on top of an array of asymmetric pinning centers show a vortex ratchet effect. A net flow of vortices is induced when the vortex lattice is driven by fluctuating forces on an array of pinning centers without reflection symmetry. This effect occurs in the adiabatic regime and it could be mimiced only by reversible DC driven forces.

  3. Antagonistic regulation of PIN phosphorylation by PP2A and PINOID directs auxin flux

    NARCIS (Netherlands)

    Michniewicz, M.; Zago, M.K.; Abas, L.; Weijers, D.; Schweighofer, A.; Meskiene, I.; Heisler, M.G.; Ohno, C.; Zhang, J.; Huang, F.; Schwab, R.; Weigel, D.; Meyerowitz, E.M.; Luschnig, C.; Offringa, R.; Friml, J.

    2007-01-01

    In plants, cell polarity and tissue patterning are connected by intercellular flow of the phytohormone auxin, whose directional signaling depends on polar subcellular localization of PIN auxin transport proteins. The mechanism of polar targeting of PINs or other cargos in plants is largely

  4. Thermoelastic properties of sandwich materials with pin-reinforced foam cores

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Pin-reinforced foam is a novel type of sandwich core materials formed by inserting pins(trusses) into a foam matrix to create a truss-like network reinforced foam core.Upon loading,the pins deform predominantly by local stretching whilst the deformation of foam is governed by local bending.This paper presents a theoretical study on the thermoelasticity of pin-reinforced foam sandwich cores.To calculate the effective thermoelastic properties of pin-reinforced foam cores,the energy-based homogenization approach is employed to develop a micromechanics-based model,calibrated by the existing experimental data.It is found that the stiffness of the sandwich core is mainly governed by pin reinforcements:the foam matrix contributes little to sandwich stiffness.Compared with traditional foam cores without pin reinforcements,the changes in inplane thermal expansion coefficients are not vigorous as a result of pin reinforcements,while the through-thickness thermal expansion coefficient changes significantly.It is also demonstrated that it is possible to design materials with zero or negative thermal expansion coefficients under such a context.

  5. Thermoelastic properties of sandwich materials with pin-reinforced foam cores

    Institute of Scientific and Technical Information of China (English)

    LU TianJian; LIU Tao; DENG ZiChen

    2008-01-01

    Pin-reinforced foam is a novel type of sandwich core materials formed by inserting pins (trusses) into a foam matrix to create a truss-like network reinforced foam core. Upon loading, the pins deform predominantly by local stretching whilst the defor-mation of foam is governed by local bending. This paper presents a theoretical study on the thermoelasllcity of pin-reinforced foam sandwich cores. To calculate the effective thermoelastic properties of pin-reinforced foam cores, the energy-based homogenization approach is employed to develop a micromechanics-based model, calibrated by the existing experimental data. It is found that the stiffness of the sandwich core is mainly governed by pin reinforcements: the foam matrix con-tributes little to sandwich stiffness. Compared with traditional foam cores without pin reinforcements, the changes in in-plane thermal expansion coefficients are not vigorous as a result of pin reinforcements, while the through-thickness thermal expansion coefficient changes significantly. It is also demonstrated that it is pos-sible to design materials with zerO or negative thermal expansion coefficients un-der such a context.

  6. Nasal foreign body: removal of an open safety pin from the left nostril.

    Science.gov (United States)

    Salley, L H; Wohl, D L

    2000-02-01

    We describe the case of a woman who presented with an open safety pin lodged in her left nostril. An attempt to remove the pin with the patient under local anesthesia was not successful. Removal was eventually accomplished in the operating room with the patient under general anesthesia.

  7. A covalent PIN1 inhibitor selectively targets cancer cells by a dual mechanism of action

    Science.gov (United States)

    Campaner, Elena; Rustighi, Alessandra; Zannini, Alessandro; Cristiani, Alberto; Piazza, Silvano; Ciani, Yari; Kalid, Ori; Golan, Gali; Baloglu, Erkan; Shacham, Sharon; Valsasina, Barbara; Cucchi, Ulisse; Pippione, Agnese Chiara; Lolli, Marco Lucio; Giabbai, Barbara; Storici, Paola; Carloni, Paolo; Rossetti, Giulia; Benvenuti, Federica; Bello, Ezia; D'Incalci, Maurizio; Cappuzzello, Elisa; Rosato, Antonio; Del Sal, Giannino

    2017-06-01

    The prolyl isomerase PIN1, a critical modifier of multiple signalling pathways, is overexpressed in the majority of cancers and its activity strongly contributes to tumour initiation and progression. Inactivation of PIN1 function conversely curbs tumour growth and cancer stem cell expansion, restores chemosensitivity and blocks metastatic spread, thus providing the rationale for a therapeutic strategy based on PIN1 inhibition. Notwithstanding, potent PIN1 inhibitors are still missing from the arsenal of anti-cancer drugs. By a mechanism-based screening, we have identified a novel covalent PIN1 inhibitor, KPT-6566, able to selectively inhibit PIN1 and target it for degradation. We demonstrate that KPT-6566 covalently binds to the catalytic site of PIN1. This interaction results in the release of a quinone-mimicking drug that generates reactive oxygen species and DNA damage, inducing cell death specifically in cancer cells. Accordingly, KPT-6566 treatment impairs PIN1-dependent cancer phenotypes in vitro and growth of lung metastasis in vivo.

  8. Effect of Pin Tool Shape on Metal Flow During Friction Stir Welding

    Science.gov (United States)

    McClure, J. C.; Coronado, E.; Aloor, S.; Nowak, B.; Murr, L. M.; Nunes, Arthur C., Jr.; Munafo, Paul M. (Technical Monitor)

    2002-01-01

    It has been shown that metal moves behind the rotating Friction Stir Pin Tool in two separate currents or streams. One current, mostly on the advancing side, enters a zone of material that rotates with the pin tool for one or more revolutions and eventually is abandoned behind the pin tool in crescent-shaped pieces. The other current, largely on the retreating side of the pin tool is moved by a wiping process to the back of the pin tool and fills in between the pieces of the rotational zone that have been shed by the rotational zone. This process was studied by using a faying surface copper trace to clarify the metal flow. Welds were made with pin tools having various thread pitches. Decreasing the thread pitch causes the large scale top-to-bottorn flow to break up into multiple vortices along the pin and an unthreaded pin tool provides insufficient vertical motion for there to be a stable rotational zone and flow of material via the rotational zone is not possible leading to porosity on the advancing side of the weld.

  9. Ginzburg-Landau vortices with pinning functions and self-similar solutions in harmonic maps

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    We obtain the H1-compactness for a system of Ginzburg-Landau equations with pinning functions and prove that the vortices of its classical solutions are attracted to the minimum points of the pinning functions. As a corollary, we construct a self-similar solution in the evolution of harmonic maps.

  10. Antagonistic regulation of PIN phosphorylation by PP2A and PINOID directs auxin flux

    NARCIS (Netherlands)

    Michniewicz, M.; Zago, M.K.; Abas, L.; Weijers, D.; Schweighofer, A.; Meskiene, I.; Heisler, M.G.; Ohno, C.; Zhang, J.; Huang, F.; Schwab, R.; Weigel, D.; Meyerowitz, E.M.; Luschnig, C.; Offringa, R.; Friml, J.

    2007-01-01

    In plants, cell polarity and tissue patterning are connected by intercellular flow of the phytohormone auxin, whose directional signaling depends on polar subcellular localization of PIN auxin transport proteins. The mechanism of polar targeting of PINs or other cargos in plants is largely unidentif

  11. Air Quality Facilities

    Data.gov (United States)

    Iowa State University GIS Support and Research FacilityFacilities with operating permits for Title V of the Federal Clean Air Act, as well as facilities required to submit an air emissions inventory, and other facilities...

  12. Theme: Laboratory Facilities Improvement.

    Science.gov (United States)

    Miller, Glen M.; And Others

    1993-01-01

    Includes "Laboratory Facilities Improvement" (Miller); "Remodeling Laboratories for Agriscience Instruction" (Newman, Johnson); "Planning for Change" (Mulcahy); "Laboratory Facilities Improvement for Technology Transfer" (Harper); "Facilities for Agriscience Instruction" (Agnew et al.); "Laboratory Facility Improvement" (Boren, Dwyer); and…

  13. Rheology of Melt-bearing Crustal Rocks

    Science.gov (United States)

    Rosenberg, C. L.; Medvedev, S.; Handy, M. R.

    2006-12-01

    A review and reinterpretation of previous experimental data on the deformation of melt-bearing crustal rocks (Rosenberg and Handy, 2005) revealed that the relationship of aggregate strength to melt fraction is non-linear, even if plotted on a linear ordinate and abscissa. At melt fractions, Φ 0.07, the dependence of aggregate strength on Φ is significantly greater than at Φ > 0.07. This melt fraction (Φ= 0.07) marks the transition from a significant increase in the proportion of melt-bearing grain boundaries up to this point to a minor increase thereafter. Therefore, we suggest that the increase of melt-interconnectivity causes the dramatic strength drop between the solidus and a melt fraction of 0.07. A second strength drop occurs at higher melt fractions and corresponds to the breakdown of the solid (crystal) framework, corresponding to the well-known "rheologically critical melt percentage" (RCMP; Arzi, 1978). Although the strength drop at the RCMP is about 4 orders of magnitude, the absolute value of this drop is small compared to the absolute strength of the unmelted aggregate, rendering the RCMP invisible in a linear aggregate strength vs. melt fraction diagram. Predicting the rheological properties and thresholds of melt-bearing crust on the basis of the results and interpretations above is very difficult, because the rheological data base was obtained from experiments performed at undrained conditions in the brittle field. These conditions are unlikely to represent the flow of partially melted crust. The measured strength of most of the experimentally deformed, partially-melted samples corresponds to their maximum differential stress, before the onset of brittle failure, not to their viscous strength during "ductile" (viscous) flow. To overcome these problems, we extrapolated a theoretically-derived flow law for partially melted granite deforming by diffusion-accommodated grain-boundary sliding (Paterson, 2001) and an experimentally-derived flow law for

  14. Viscosity model for aluminosilicate melt

    Directory of Open Access Journals (Sweden)

    Zhang G.H.

    2012-01-01

    Full Text Available The structurally based viscosity model proposed in our previous study is extended to include more components, e.g. SiO2, Al2O3, FeO, MnO, MgO, CaO, Na2O and K2O. A simple method is proposed to calculate the numbers of different types of oxygen ions classified by the different cations they bonded with, which is used to characterize the influence of composition on viscosity. When dealing with the aluminosilicate melts containing several basic oxides, the priority order is established for different cations for charge compensating Al3+ ions, according to the coulombic force between cation and oxygen anion. It is indicated that basic oxides have two paradox influences on viscosity: basic oxide with a higher basicity decreases viscosity more greatly by forming weaker non-bridging oxygen bond; while it increases viscosity more greatly by forming stronger bridging oxygen bond in tetrahedron after charge compensating Al3+ ion. The present model can extrapolate its application range to the system without SiO2. Furthermore, it could also give a satisfy interpretation to the abnormal phenomenon that viscosity increases when adding K2O to CaO-Al2O3-SiO2 melt within a certain composition range.

  15. Preparation of the initial solid liquid interface and melt in directional solidification

    Science.gov (United States)

    Nguyen Thi, H.; Drevet, B.; Debierre, J. M.; Camel, D.; Dabo, Y.; Billia, B.

    2003-06-01

    The preparation of the initial conditions (solid-liquid interface morphology and solute segregation in the liquid phase) on which growth is started is a very critical step in directional-solidification experiments. Dedicated experiments on Al-1.5 wt% Ni consisting in directional melting followed by thermal stabilisation with different lengths, show that precise control is in practice not straightforward. Indeed, in the mushy zone created by melting the original solid sample, temperature gradient zone melting (TGZM) causes migration of solute-rich liquid droplets and channels. A model is proposed to describe this process and validate the physical interpretation of the experiments through numerical simulation. Knowing the status of the preparation, the intriguing observations in the partially melted region of the Al-1.5 wt% Ni alloys solidified in the Advanced Gradient Heating Facility of European Space Agency during the LMS and STS-95 space missions can now be explained. Finally, the influence of initial interface morphology and melt segregation on directional-solidification transient is discussed, based on a comparison of Al-Ni alloys with hypoeutectic Al-Li alloys previously grown on Earth and in space. It follows that for experiments achieved on original rods with equiaxed microstructure, the efficiency of the preparatory melting and stabilisation phases can be evaluated from the solute macrosegregation profile in the region in between the non-melted solid and directional solidification. The major conclusion is that when the melt is mixed by fluid flow, the initial conditions are near to their asymptotic state at the end of TGZM whereas, when solute diffusion is the mode of transport into the bulk liquid, the condition of homogeneous melt becomes limiting and too much time-consuming to be fulfilled, which in particular holds for the 3D-experiments carried out in the reduced-gravity environment of space.

  16. Pin1 Modulates the Synaptic Content of NMDA Receptors via Prolyl-Isomerization of PSD-95.

    Science.gov (United States)

    Antonelli, Roberta; De Filippo, Roberto; Middei, Silvia; Stancheva, Stefka; Pastore, Beatrice; Ammassari-Teule, Martine; Barberis, Andrea; Cherubini, Enrico; Zacchi, Paola

    2016-05-18

    Phosphorylation of serine/threonine residues preceding a proline regulates the fate of its targets through postphosphorylation conformational changes catalyzed by the peptidyl-prolyl cis-/trans isomerase Pin1. By flipping the substrate between two different functional conformations, this enzyme exerts a fine-tuning of phosphorylation signals. Pin1 has been detected in dendritic spines and shafts where it regulates protein synthesis required to sustain the late phase of long-term potentiation (LTP). Here, we demonstrate that Pin1 residing in postsynaptic structures can interact with postsynaptic density protein-95 (PSD-95), a key scaffold protein that anchors NMDA receptors (NMDARs) in PSD via GluN2-type receptor subunits. Pin1 recruitment by PSD-95 occurs at specific serine-threonine/proline consensus motifs localized in the linker region connecting PDZ2 to PDZ3 domains. Upon binding, Pin1 triggers structural changes in PSD-95, thus negatively affecting its ability to interact with NMDARs. In electrophysiological experiments, larger NMDA-mediated synaptic currents, evoked in CA1 principal cells by Schaffer collateral stimulation, were detected in hippocampal slices obtained from Pin1(-/-) mice compared with controls. Similar results were obtained in cultured hippocampal cells expressing a PSD-95 mutant unable to undergo prolyl-isomerization, thus indicating that the action of Pin1 on PSD-95 is critical for this effect. In addition, an enhancement in spine density and size was detected in CA1 principal cells of Pin1(-/-) or in Thy-1GFP mice treated with the pharmacological inhibitor of Pin1 catalytic activity PiB.Our data indicate that Pin1 controls synaptic content of NMDARs via PSD-95 prolyl-isomerization and the expression of dendritic spines, both required for LTP maintenance. PSD-95, a membrane-associated guanylate kinase, is the major scaffolding protein at excitatory postsynaptic densities and a potent regulator of synaptic strength and plasticity. The

  17. Snow Melting and Freezing on Older Townhouses

    DEFF Research Database (Denmark)

    Nielsen, Anker; Claesson, Johan

    2011-01-01

    The snowy winter of 2009/2010 in Scandinavia prompted many newspaper articles on icicles falling from buildings and the risk this presented for people walking below. The problem starts with snow melting on the roof due to heat loss from the building. Melt water runs down the roof and some...... of it will freeze on the overhang. The rest of the water will either run off or freeze in gutters and downpipes or turn into icicles. This paper describes use of a model for the melting and freezing of snow on roofs. Important parameters are roof length, overhang length, heat resistance of roof and overhang......, outdoor and indoor temperature, snow thickness and thermal conductivity. If the snow thickness is above a specific limit value – the snow melting limit- some of the snow will melt. Another interesting limit value is the dripping limit. All the melt water will freeze on the overhang, if the snow thickness...

  18. RHEOLOGY FEATURE OF SIMPLE METAL MELT

    Institute of Scientific and Technical Information of China (English)

    C.J. Sun; H.R. Geng; Y.S. Shen; X.Y. Teng; Z.X. Yang

    2007-01-01

    The rheology feature of Sb, Bi melt and alloys was studied using coaxial cylinder high-temperature viscometer. The results showed that the curve of torsion-rotational speed for Sb melt presents a linear relation in all measured temperature ranges, whereas for the Bi melt, the curve presents obvious non-Newtonian feature within the low temperature range and at relative high shear stress. The rheology feature of Sb80Bi20 and Sb20Bi80, alloy melts was well correlated with that of Sb and Bi, respectively. It is considered that the rheology behavior of Sb melt plays a crucial role in Sb80Bi20, alloy and that of Bi melt plays a crucial role in Sb20Bi80 alloy.

  19. Cross section generation for LWR pin lattices simulations

    Energy Technology Data Exchange (ETDEWEB)

    Velasquez, Carlos E.; Macedo, Anderson A.P.; Cardoso, Fabiano S.; Pereira, Claubia; Veloso, Maria Auxiliadora F.; Costa, Antonella L. [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil); Instituto Nacional de Ciencia e Tecnologia de Reatores Nucleares Inovadores/CNPq, Brasilia, DF (Brazil); Barros, Graiciany de P. [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    The majority of the neutron data library provided with the MCNP code is set at room temperature. Therefore, it is important to generate continuous energy cross section library for MCNP code for different temperatures. To evaluate the methodology used, the criticality calculations obtained using MCNP with the cross section generated at DEN/UFMG, are compared with the criticality data from the International Handbook of Evaluated Reactor Physics Benchmarks Experiments about the PIN lattices for light water reactors. It was used nuclear data from the ENDF-VII.1, JEFF-3.1 and TENDL-2014, which were processed using the NJOY99 code for different energies and temperatures. This code provides the nuclear data in ACE libraries, which then are added to MCNP libraries to perform the simulations. The results indicate the methodology efficiency developed by DEN/UFMG. (author)

  20. PINS Measurements of Explosive Simulants for Cargo Screening

    Energy Technology Data Exchange (ETDEWEB)

    E.H. Seabury

    2008-06-01

    As part of its efforts to prevent the introduction of explosive threats on commercial flights, the Transportation Security Administration (TSL) is evaluating new explosives detection systems (EDSs) for use in air cargo inspection. The TSL has contracted Battelle to develop a new type of explosives simulant to assist in this development. These are designed to mimic the elemental profile (C, H, N, O, etc.) of explosives as well as their densities. Several “neutron in—gamma out” (n,?) techniques have been considered to quantify the elemental profile in these new simulants and the respective explosives. The method chosen by Battelle is Portable Isotopic Neutron Spectroscopy (PINS), developed by Idaho National Laboratory (INL). Battelle wishes to validate that the simulants behave like the explosive threats with this technology. The results of the validation measurements are presented in this report.

  1. Detecting pin diversion from pressurized water reactors spent fuel assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Ham, Young S.; Sitaraman, Shivakumar

    2017-01-10

    Detecting diversion of spent fuel from Pressurized Water Reactors (PWR) by determining possible diversion including the steps of providing a detector cluster containing gamma ray and neutron detectors, inserting the detector cluster containing the gamma ray and neutron detectors into the spent fuel assembly through the guide tube holes in the spent fuel assembly, measuring gamma ray and neutron radiation responses of the gamma ray and neutron detectors in the guide tube holes, processing the gamma ray and neutron radiation responses at the guide tube locations by normalizing them to the maximum value among each set of responses and taking the ratio of the gamma ray and neutron responses at the guide tube locations and normalizing the ratios to the maximum value among them and producing three signatures, gamma, neutron, and gamma-neutron ratio, based on these normalized values, and producing an output that consists of these signatures that can indicate possible diversion of the pins from the spent fuel assembly.

  2. Vortex pinning and dynamics in the neutron star crust

    CERN Document Server

    Wlazłowski, Gabriel; Magierski, Piotr; Bulgac, Aurel; Forbes, Michael McNeil

    2016-01-01

    The nature of the interaction between superfluid vortices and the neutron star crust, conjectured by Anderson and Itoh in 1975 to be at the heart vortex creep and the cause of glitches, has been a longstanding question in astrophysics. Previous estimates of the vortex-"nucleus" interaction have been error-prone, being either phenomenological or derived from tiny differences of large energies of stationary configurations. Using a qualitatively new approach, we follow the dynamics as superfluid vortices move in response to the presence of "nuclei" (nuclear defects in the crust). The resulting motion is perpendicular to the force, similar to the motion of a spinning top when pushed. We show that nuclei repel vortices in the neutron star crust, leading thus to interstitial vortex pinning, and characterize the force as a function of the vortex-nucleus separation.

  3. Gratings and Random Reflectors for Near-Infrared PIN Diodes

    Science.gov (United States)

    Gunapala, Sarath; Bandara, Sumith; Liu, John; Ting, David

    2007-01-01

    Crossed diffraction gratings and random reflectors have been proposed as means to increase the quantum efficiencies of InGaAs/InP positive/intrinsic/ negative (PIN) diodes designed to operate as near-infrared photodetectors. The proposal is meant especially to apply to focal-plane imaging arrays of such photodetectors to be used for near-infrared imaging. A further increase in quantum efficiency near the short-wavelength limit of the near-infrared spectrum of such a photodetector array could be effected by removing the InP substrate of the array. The use of crossed diffraction gratings and random reflectors as optical devices for increasing the quantum efficiencies of quantum-well infrared photodetectors (QWIPs) was discussed in several prior NASA Tech Briefs articles. While the optical effects of crossed gratings and random reflectors as applied to PIN photodiodes would be similar to those of crossed gratings and random reflectors as applied to QWIPs, the physical mechanisms by which these optical effects would enhance efficiency differ between the PIN-photodiode and QWIP cases: In a QWIP, the multiple-quantum-well layers are typically oriented parallel to the focal plane and therefore perpendicular or nearly perpendicular to the direction of incidence of infrared light. By virtue of the applicable quantum selection rules, light polarized parallel to the focal plane (as normally incident light is) cannot excite charge carriers and, hence, cannot be detected. A pair of crossed gratings or a random reflector scatters normally or nearly normally incident light so that a significant portion of it attains a component of polarization normal to the focal plane and, hence, can excite charge carriers. A pair of crossed gratings or a random reflector on a PIN photodiode would also scatter light into directions away from the perpendicular to the focal plane. However, in this case, the reason for redirecting light away from the perpendicular is to increase the length of the

  4. Dynamic interaction of fingertip skin and pin of tactile device

    Science.gov (United States)

    Grigas, Vytautas; Tolocka, Rymantas T.; Ziliukas, Pranas

    2007-12-01

    The present paper deals with investigations performed with the aim to study transmitting tactile information into the area of mechanoreceptors of the fingertip skin segment and to estimate the dynamic properties and behavior of the skin by performing numerical analysis. A computational finite element model consisting of four main layers of skin was used for transient analysis of contact dynamic interaction when loading the skin by a moving pin, as well as for modal analysis of skin and analysis of skin stress-strain state under harmonic loading (a plane strain case was studied). Material properties of the skin were assumed as linear elastic because of a very small excitation signal level. The efficiency of the regime of the skin dynamic loading in terms of the tactile signal level was defined on the basis of the strain level in the dermis zone where mechanoreceptors are placed. The possibilities of using vibratory control signal were analyzed.

  5. High-performance monolithic PIN-MODFET transimpedance photoreceiver

    Science.gov (United States)

    Gutierrez-Aitken, A. L.; Bhattacharya, P.; Chen, Y. C.; Pavlidis, D.; Brock, T.

    1993-08-01

    The performance characteristics of a transimpedance photoreceiver using an In(0.53)Ga(0.47)As p-i-n photodiode integrated with a 0.1-micron gate length regrown pseudomorphic In(0.60)Ga(0.40)As MODFET grown by MBE were investigated. The regrown MODFET's have extrinsic transconductance values as high as 610 mS/mm and channel currents up to 350 mA/mm at a drain bias of 1.5 V. The measured temporal response of the photoreceiver exhibits a FWHM value of 90 ps, which indicates a bandwidth of approximately 6 GHz and expected 10-Gb/s operation. The transimpedance gain was as high as 55 dB-ohm with an 800-ohm feedback resistor.

  6. Sharp critical behavior for pinning model in random correlated environment

    CERN Document Server

    Berger, Quentin

    2011-01-01

    This article investigates the effect for random pinning models of long range power-law decaying correlations in the environment. For a particular type of environment based on a renewal construction, we are able to sharply describe the phase transition from the delocalized phase to the localized one, giving the critical exponent for the (quenched) free-energy, and proving that at the critical point the trajectories are fully delocalized. These results contrast with what happens both for the pure model (i.e. without disorder) and for the widely studied case of i.i.d. disorder, where the relevance or irrelevance of disorder on the critical properties is decided via the so-called Harris Criterion.

  7. Using Pin as a Memory Reference Generator for Multiprocessor Simulation

    Energy Technology Data Exchange (ETDEWEB)

    McCurdy, C

    2005-10-22

    In this paper we describe how we have used Pin to generate a multithreaded reference stream for simulation of a multiprocessor on a uniprocessor. We have taken special care to model as accurately as possible the effects of cache coherence protocol state, and lock and barrier synchronization on the performance of multithreaded applications running on multiprocessor hardware. We first describe a simplified version of the algorithm, which uses semaphores to synchronize instrumented application threads and the simulator on every memory reference. We then describe modifications to that algorithm to model the microarchitectural features of the Itanium2 that affect the timing of memory reference issue. An experimental evaluation determines that while cycle-accurate multithreaded simulation is possible using our approach, the use of semaphores has a negative impact on the performance of the simulator.

  8. Model of Ni-63 battery with realistic PIN structure

    Energy Technology Data Exchange (ETDEWEB)

    Munson, Charles E.; Voss, Paul L.; Ougazzaden, Abdallah, E-mail: aougazza@georgiatech-metz.fr [Georgia Tech Lorraine, Georgia Tech-C.N.R.S., UMI2958, 2-3 rue Marconi, 57070 Metz (France); School of Electrical and Computer Engineering, Georgia Institute of Technology, 777 Atlantic Drive NW, 30332-0250 Atlanta (United States); Arif, Muhammad; Salvestrini, Jean-Paul [Georgia Tech Lorraine, Georgia Tech-C.N.R.S., UMI2958, 2-3 rue Marconi, 57070 Metz (France); Université de Lorraine, CentraleSupélec, LMOPS, EA 4423, 2 rue E. Belin, 57070 Metz (France); Streque, Jeremy; El Gmili, Youssef [Georgia Tech Lorraine, Georgia Tech-C.N.R.S., UMI2958, 2-3 rue Marconi, 57070 Metz (France); Belahsene, Sofiane; Martinez, Anthony; Ramdane, Abderrahim [Laboratory for Photonics and Nanostructures, CNRS, Route de Nozay, 91460 Marcoussis (France)

    2015-09-14

    GaN, with its wide bandgap of 3.4 eV, has emerged as an efficient material for designing high-efficiency betavoltaic batteries. An important part of designing efficient betavoltaic batteries involves a good understanding of the full process, from the behavior of the nuclear material and the creation of electron-hole pairs all the way through the collection of photo-generated carriers. This paper presents a detailed model based on Monte Carlo and Silvaco for a GaN-based betavoltaic battery device, modeled after Ni-63 as an energy source. The accuracy of the model is verified by comparing it with experimental values obtained for a GaN-based p-i-n structure under scanning electron microscope illumination.

  9. Statistical mechanics of homogeneous partly pinned fluid systems.

    Science.gov (United States)

    Krakoviack, Vincent

    2010-12-01

    The homogeneous partly pinned fluid systems are simple models of a fluid confined in a disordered porous matrix obtained by arresting randomly chosen particles in a one-component bulk fluid or one of the two components of a binary mixture. In this paper, their configurational properties are investigated. It is shown that a peculiar complementarity exists between the mobile and immobile phases, which originates from the fact that the solid is prepared in presence of and in equilibrium with the adsorbed fluid. Simple identities follow, which connect different types of configurational averages, either relative to the fluid-matrix system or to the bulk fluid from which it is prepared. Crucial simplifications result for the computation of important structural quantities, both in computer simulations and in theoretical approaches. Finally, possible applications of the model in the field of dynamics in confinement or in strongly asymmetric mixtures are suggested.

  10. Fulx-pinning mechanism and activation energy in malic acid-doped MgB2

    Directory of Open Access Journals (Sweden)

    SR Ghorbani

    2010-09-01

    Full Text Available Fulx-pinning mechanism and activation energy of MgB2 doped with 10 wt % malic- acid has been investigated by measurement of critical current density and resistivity as a function of magnetic fields and temperatures. The field dependence of the critical current density, Jc(B, was analyzed within the collective pinning model. A crossover field, Bsb, from the single vortex to the small vortex bundle-pinning regime was observed. For sintered sample, the temperature dependence of Bsb(T at low temperature is in good agreement with the δℓ pinning mechanism, i.e., pinning associated with charge-carrier mean free path fluctuation. The activation energy was decreased linearly by increasing magnetic field.

  11. Prophylactic pinning for slipped capital femoral epiphysis: does it affect proximal femoral morphology?

    Science.gov (United States)

    Cousins, Gerard R; Campbell, Donald M; Wilson, Neil I L; Maclean, Jamie G B

    2016-05-01

    This study was designed to determine whether prophylactic pinning of the unaffected hip in unilateral slipped capital femoral epiphysis affects the proximal femoral morphology. Twenty-four hips prophylactically pinned were compared with 26 cases observed. The articulotrochanteric distance (ATD) and the trochanteric-trochanteric distance (TTD) were measured. Postoperative radiographs were compared with final follow-up radiographs. The final TTD : ATD ratio was higher (P=0.048) in the pinned group, suggesting relative coxa vara/breva. There was a smaller difference between the two hips in the prophylactically pinned group (0.7) as opposed to those observed (1.47). Prophylactic pinning does not cause growth to stop immediately but alters the proximal femoral morphology.

  12. Synchronization for an array of neural networks with hybrid coupling by a novel pinning control strategy.

    Science.gov (United States)

    Gong, Dawei; Lewis, Frank L; Wang, Liping; Xu, Ke

    2016-05-01

    In this paper, a novel pinning synchronization (synchronization with pinning control) scheme for an array of neural networks with hybrid coupling is investigated. The main contributions are as follows: (1) A novel pinning control strategy is proposed for the first time. Pinning control schemes are introduced as an array of column vector. The controllers are designed as simple linear systems, which are easy to be analyzed or tested. (2) Augmented Lyapunov-Krasovskii functional (LKF) is applied to introduce more relax variables, which can alleviate the requirements of the positive definiteness of the matrix. (3) Based on the appropriate LKF, by introducing some free weighting matrices, some novel synchronization criteria are derived. Furthermore, the proposed pinning control scheme described by column vector can also be expanded to almost all the other array of neural networks. Finally, numerical examples are provided to show the effectiveness of the proposed results.

  13. Cell polarity and patterning by PIN trafficking through early endosomal compartments in Arabidopsis thaliana.

    Directory of Open Access Journals (Sweden)

    Hirokazu Tanaka

    2013-05-01

    Full Text Available PIN-FORMED (PIN proteins localize asymmetrically at the plasma membrane and mediate intercellular polar transport of the plant hormone auxin that is crucial for a multitude of developmental processes in plants. PIN localization is under extensive control by environmental or developmental cues, but mechanisms regulating PIN localization are not fully understood. Here we show that early endosomal components ARF GEF BEN1 and newly identified Sec1/Munc18 family protein BEN2 are involved in distinct steps of early endosomal trafficking. BEN1 and BEN2 are collectively required for polar PIN localization, for their dynamic repolarization, and consequently for auxin activity gradient formation and auxin-related developmental processes including embryonic patterning, organogenesis, and vasculature venation patterning. These results show that early endosomal trafficking is crucial for cell polarity and auxin-dependent regulation of plant architecture.

  14. Multiscale Models of Melting Arctic Sea Ice

    Science.gov (United States)

    2014-09-30

    1 Multiscale Models of Melting Arctic Sea Ice Kenneth M. Golden University of Utah, Department of Mathematics phone: (801) 581-6851...feedback has played a major role in the recent declines of the summer Arctic sea ice pack. However, understanding the evolution of melt ponds and sea...Models of Melting Arctic Sea Ice 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER

  15. Melt Dispersion and Direct Containment Heating (DCH) Experiments für KONVOI reactors (KIT Scientific Reports ; 7567)

    OpenAIRE

    Meyer, Leonhard

    2010-01-01

    The DISCO-H test facility was used to perform scaled experiments that simulate melt ejection scenarios under low system pressure in Severe Accidents in Pressurized Water Reactors (PWR). These experiments are designed to investigate the fluid-dynamic, thermal and chemical processes during melt ejection out of a breach in the lower head of a PWR pressure vessel at pressures around and below 2 MPa with an iron-alumina melt and steam. The report presents results from a test series with the geomet...

  16. Decontamination of metals by melt refinings/slagging: An annotated bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Mizia, R.E. [ed.; Worcester, S.A.; Twidwell, L.G.; Paolini, D.J.; Weldon, T.A.

    1993-07-01

    As the number of nuclear installations undergoing decontamination and decommissioning (D&D) increases, current radioactive waste storage space is consumed and establishment of new waste storage areas becomes increasingly difficult, the problem of handling and storing radioactive scrap metal (RSM) gains increasing importance in the DOE Environmental Restoration and Waste Management Program. To alleviate present and future waste storage problems, Westinghouse Idaho Nuclear Company (WINCO) is managing a program for the recycling of RSM for beneficial use within the DOE complex. As part of that effort, Montana Tech has been awarded a contract to help optimize melting and refining technology for the recycling of stainless steel RSM. The scope of the Montana Tech program includes a literature survey, a decontaminating slag design study, small scale melting studies to determine optimum slag compositions for removal of radioactive contaminant surrogates, analysis of preferred melting techniques, and coordination of large scale melting demonstrations (100--500 lbs) to be conducted at selected facilities. The program will support recycling and decontaminating stainless steel RSM for use in waste canisters for Idaho Waste Immobilization Facility densified high level waste. This report is the result of the literature search conducted to establish a basis for experimental melt/slag program development.

  17. Nitric-glycolic flowsheet evaluation with the slurry-fed melt rate furnace

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M. S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fowley, M. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Zamecnik, J. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-03-01

    The Savannah River National Laboratory (SRNL) was tasked to support validation of the Defense Waste Processing Facility (DWPF) melter offgas flammability model for the nitric-glycolic (NG) flowsheet. The work supports Deliverable 4 of the DWPF & Saltstone Facility Engineering Technical Task Request (TTR)1 and is supplemental to the Cold Cap Evaluation Furnace (CEF) testing conducted in 2014.2 The Slurry-fed Melt Rate Furnace (SMRF) was selected for the supplemental testing as it requires significantly less resources than the CEF and could provide a tool for more rapid analysis of melter feeds in the future. The SMRF platform has been used previously to evaluate melt rate behavior of DWPF glasses, but was modified to accommodate analysis of the offgas stream. Additionally, the Melt Rate Furnace (MRF) and Quartz Melt Rate Furnace (QMRF) were utilized for evaluations. MRF data was used exclusively for melt behavior observations and REDuction/OXidation (REDOX) prediction comparisons and will be briefly discussed in conjunction with its support of the SMRF testing. The QMRF was operated similarly to the SMRF for the same TTR task, but will be discussed in a separate future report. The overall objectives of the SMRF testing were to; 1) Evaluate the efficacy of the SMRF as a platform for steady state melter testing with continuous feeding and offgas analysis; and 2) Generate supplemental melter offgas flammability data to support the melter offgas flammability modelling effort for DWPF implementation of the NG flowsheet.

  18. Decontamination of metals by melt refining/slagging: First year progress report

    Energy Technology Data Exchange (ETDEWEB)

    Mizia, R.E. [ed.; Worcester, S.A.; Twidwell, L.G.; Paolini, D.J.; Weldon, T.A.

    1994-03-01

    As the number of nuclear installations undergoing decontamination and decommissioning (D&D) increases, current radioactive waste storage space is consumed and establishment of new waste storage areas becomes increasingly difficult. The problem of handling and storing radioactive scrap metal (RSM) gains increasing importance in the DOE Environmental Restoration and Waste Management Program. To alleviate present and future waste storage problems, Westinghouse Idaho Nuclear Company (WINCO) is managing a program for the recycling of RSM for beneficial use within the DOE complex. As part of that effort, Montana Tech has been awarded a contract to help optimize melting and refining technologies for the recycling of stainless steel RSM. The scope of the Montana Tech program includes a literature survey, a decontaminating slag design study, small scale melting studies to determine optimum slag compositions for removal of radioactive contaminant surrogates, analysis of preferred melting techniques, and coordination of pilot scale melting demonstrations (100-500 lbs) to be conducted at selected commercial facilities. This program will identify methods that can be used to recycle stainless steel RSM which will be used to fabricate high and low level waste canisters for the Idaho Waste Immobilization Facility. This report summarizes the results of an extensive literature review and the first year`s progress on slag design, small-scale melt refining of surrogate-containing stainless steel (presently only a three month effort), and pilot-scale preparation of surrogate master ingots.

  19. Melt processing of radioactive waste: A technical overview

    Energy Technology Data Exchange (ETDEWEB)

    Schlienger, M.E.; Buckentin, J.M.; Damkroger, B.K.

    1997-04-01

    Nuclear operations have resulted in the accumulation of large quantities of contaminated metallic waste which are stored at various DOE, DOD, and commercial sites under the control of DOE and the Nuclear Regulatory Commission (NRC). This waste will accumulate at an increasing rate as commercial nuclear reactors built in the 1950s reach the end of their projected lives, as existing nuclear powered ships become obsolete or unneeded, and as various weapons plants and fuel processing facilities, such as the gaseous diffusion plants, are dismantled, repaired, or modernized. For example, recent estimates of available Radioactive Scrap Metal (RSM) in the DOE Nuclear Weapons Complex have suggested that as much as 700,000 tons of contaminated 304L stainless steel exist in the gaseous diffusion plants alone. Other high-value metals available in the DOE complex include copper, nickel, and zirconium. Melt processing for the decontamination of radioactive scrap metal has been the subject of much research. A major driving force for this research has been the possibility of reapplication of RSM, which is often very high-grade material containing large quantities of strategic elements. To date, several different single and multi-step melting processes have been proposed and evaluated for use as decontamination or recycling strategies. Each process offers a unique combination of strengths and weaknesses, and ultimately, no single melt processing scheme is optimum for all applications since processes must be evaluated based on the characteristics of the input feed stream and the desired output. This paper describes various melt decontamination processes and briefly reviews their application in developmental studies, full scale technical demonstrations, and industrial operations.

  20. Impact Melt in Small Lunar Highlands Craters

    Science.gov (United States)

    Plescia, J. B.; Cintala, M. J.; Robinson, M. S.; Barnouin, O.; Hawke, B. R.

    2011-01-01

    Impact-melt deposits are a typical characteristic of complex impact craters, occurring as thick pools on the crater floor, ponds on wall terraces, veneers on the walls, and flows outside and inside the rim. Studies of the distribution of impact melt suggested that such deposits are rare to absent in and around small (km to sub-km), simple impact craters. noted that the smallest lunar crater observed with impact melt was approximately 750 m in diameter. Similarly, theoretical models suggest that the amount of melt formed is a tiny fraction (crater volume and thus significant deposits would not be expected for small lunar craters. LRO LROC images show that impact-melt deposits can be recognized associated with many simple craters to diameters down to approximately 200 m. The melt forms pools on the crater floor, veneer on the crater walls or ejecta outside the crater. Such melt deposits are relatively rare, and can be recognized only in some fresh craters. These observations indicate that identifiable quantities of impact melt can be produced in small impacts and the presence of such deposits shows that the material can be aggregated into recognizable deposits. Further, the present of such melt indicates that small craters could be reliably radiometrically dated helping to constrain the recent impact flux.

  1. Low Melt Height Solidification of Superalloys

    Science.gov (United States)

    Montakhab, Mehdi; Bacak, Mert; Balikci, Ercan

    2016-06-01

    Effect of a reduced melt height in the directional solidification of a superalloy has been investigated by two methods: vertical Bridgman (VB) and vertical Bridgman with a submerged baffle (VBSB). The latter is a relatively new technique and provides a reduced melt height ahead of the solidifying interface. A low melt height leads to a larger primary dendrite arm spacing but a lower mushy length, melt-back transition length, and porosity. The VBSB technique yields up to 38 pct reduction in the porosity. This may improve a component's mechanical strength especially in a creep-fatigue type dynamic loading.

  2. Solute Redistribution in Directional Melting Process

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@The solute redistribution in directional melting process is theoretically studied. Based on quantitative evaluations, uniform solute distribution in liquid and a quasi-steady solute distribution in solid are supposed. The discussion on the solute balance comes to a simple model for the solute redistribution in directional melting process. As an example, the variation of liquid composition during melting process of carbon steel is quantitatively evaluated using the model. Results show that the melting of an alloy starts at solidus temperature, but approaches the liquidus temperature after a very short transient process.

  3. Dynamics of two-dimensional vortex system in a strong square pinning array at the second matching field

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Qing-Bao [Department of Physics, Lishui University, Lishui 323000 (China); Luo, Meng-Bo, E-mail: Luomengbo@zju.edu.cn [Department of Physics, Zhejiang University, Hangzhou 310027 (China)

    2013-10-30

    We study the dynamics of a two-dimensional vortex system in a strong square pinning array at the second matching field. Two kinds of depinning behaviors, a continuous depinning transition at weak pinning and a discontinuous one at strong pinning, are found. We show that the two different kinds of vortex depinning transitions can be identified in transport as a function of the pinning strength and temperature. Moreover, interstitial vortex state can be probed from the transport properties of vortices.

  4. Pinning efficiency of splayed columnar defects in Bi-2212 single crystal: Evidence of a cage pinning effect

    Science.gov (United States)

    Shaidiuk, V. A.; Ruyter, A.; Plessis, D.; Simon, Ch.; Maignan, A.; Wahl, A.; de Brion, S.; Ammor, L.

    2011-05-01

    A three-directional configuration of columnar defects has been induced in a Bi2Sr2CaCu2O8 single crystal by irradiation with heavy ions of high energy. Persistent current densities have been extracted, using the Bean model, from hysteresis loops recorded in the orientation H||c. We have shown that improvements in pinning properties are larger in this three-directional splayed configuration than in the one obtained with columnar defects parallel to the c-axis. This effect exists only for H larger than HΦ, where HΦ is the matching field, and disappears as temperature is increased and vortices become less stiff. This is the first time that such a beneficial effect is reported for a compound of such a high electronic anisotropy.

  5. Melting and Sintering of Ashes

    DEFF Research Database (Denmark)

    Hansen, Lone Aslaug

    1997-01-01

    The thesis contains an experimental study of the fusion and sintering of ashes collected during straw and coal/straw co-firing.A laboratory technique for quantitative determination of ash fusion has been developed based on Simultaneous Thermal Analysis (STA). By means of this method the fraction...... of melt in the investigated ashes has been determined as a function of temperature. Ash fusion results have been correlated to the chemical and mineralogical composition of the ashes, to results from a standard ash fusion test and to results from sintering experiments. Furthermore, the ash fusion results......-firing, the model only had a qualitative agreement with the measured ash deposit formation rates.Sintering measurements were carried out by means of compression strength testing of ash pellets. This method showed to not be applicable for the salt rich fly ash derived from straw combustion. For the fly ashes...

  6. Exploration of the fragmentation of laser shock-melted aluminum using x-ray backlighting

    Science.gov (United States)

    Zhang, Lin; Li, Ying-Hua; Li, Xue-Mei; Ye, Xiang-Ping; Zhang, Zu-Gen; Cheng, Jin-Ming; Cai, Ling-Cang

    2016-05-01

    The fragmentation of shock-melted metal material is an important scientific problem in shock physics and is suitable for experimentally investigating by the laser-driven x-ray backlighting technique. This letter reports on the exploration of laser shock-melted aluminum fragmentation by means of x-ray backlighting at the SGII high energy facility in China. High-quality and high-resolution radiographs with negligible motion blur were obtained and these images enabled analysis of the mass distribution of the fragmentation product.

  7. Do Melt Inclusions Answer Big Questions?

    Science.gov (United States)

    Hofmann, A. W.; Sobolev, A. V.

    2009-12-01

    In a pioneering paper, Sobolev and Shimizu (1993) demonstrated the existence of ultra-depleted melt inclusions in olivine phenocrysts in MORB. They interpreted these as evidence for the preservation of parental melts formed by progressive near-fractional melting. Subsequently many cases have been described where melt inclusions from single basalt samples display enormous chemical and isotopic heterogeneity. The interpretation of these observations hinges critically on whether such melt inclusions can faithfully preserve primary or parental melt composition. If they do, melt inclusion data can truly answer big questions from small-scale observations. If they do not, they answer rather small questions. Favoring the second possibility, Danyushevsky et al. (2004) have suggested that much of the observed variability of highly incompatible trace elements in melt inclusions “may not represent geologically significant melts, but instead reflect localized, grain-scale reaction processes within the magmatic plumbing system.” We disagree and show that this mechanism cannot, for example, explain isotopic heterogeneity measured in several suites of melt inclusions, nor does it not account for the presence of ultra-depleted melts and "ghost" plagioclase signatures in other inclusions. More recently, Spandler et al. (2007) have suggested on the basis of experimental evidence that diffusion rates for REE in olivine are so rapid that parental melt compositions in melt inclusions are rapidly falsified by diffusional exchange with (evolved) host lava. We show that the very fact that extreme chemical and isotopic heterogeneities are routinely preserved in melt inclusions demonstrates that this conclusion is unwarranted, either because residence times of the olivine phenocrysts are much shorter than assumed by Spandler et al. or because the high experimental diffusion rates are caused by an unknown experimental artifact. Although there is no obvious flaw in design and execution of

  8. A ROP GTPase-dependent auxin signaling pahtway regulates the subcellular distribution of PIN2 in Arabidopsis roots

    NARCIS (Netherlands)

    Lin, D.; Nagawa, S.; Chen, J.; Cao, L.; Scheres, B.

    2012-01-01

    PIN-FORMED (PIN) protein-mediated auxin polar transport is critically important for development, pattern formation, and morphogenesis in plants. Auxin has been implicated in the regulation of polar auxin transport by inhibiting PIN endocytosis [1 and 2], but how auxin regulates this process is

  9. A ROP GTPase-dependent auxin signaling pahtway regulates the subcellular distribution of PIN2 in Arabidopsis roots

    NARCIS (Netherlands)

    Lin, D.; Nagawa, S.; Chen, J.; Cao, L.; Scheres, B.

    2012-01-01

    PIN-FORMED (PIN) protein-mediated auxin polar transport is critically important for development, pattern formation, and morphogenesis in plants. Auxin has been implicated in the regulation of polar auxin transport by inhibiting PIN endocytosis [1 and 2], but how auxin regulates this process is poorl

  10. Evaluation of FFTF fuel pin design procedure vis-a-vis steady state irradiation performance in EBR II

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, R.J.

    1976-11-01

    The FFTF fuel pin design analysis is shown to be conservative through comparison with pin irradiation experience in EBR-II. This comparison shows that the actual lifetimes of EBR-II fuel pins are either greater than 80,000 MWd/MTM or greater than the calculated allowable lifetimes based on thermal creep strain.

  11. A benchmark initiative on mantle convection with melting and melt segregation

    Science.gov (United States)

    Schmeling, Harro; Dannberg, Juliane; Dohmen, Janik; Kalousova, Klara; Maurice, Maxim; Noack, Lena; Plesa, Ana; Soucek, Ondrej; Spiegelman, Marc; Thieulot, Cedric; Tosi, Nicola; Wallner, Herbert

    2016-04-01

    In recent years a number of mantle convection models have been developed which include partial melting within the asthenosphere, estimation of melt volumes, as well as melt extraction with and without redistribution at the surface or within the lithosphere. All these approaches use various simplifying modelling assumptions whose effects on the dynamics of convection including the feedback on melting have not been explored in sufficient detail. To better assess the significance of such assumptions and to provide test cases for the modelling community we carry out a benchmark comparison. The reference model is taken from the mantle convection benchmark, cases 1a to 1c (Blankenbach et al., 1989), assuming a square box with free slip boundary conditions, the Boussinesq approximation, constant viscosity and Rayleigh numbers of 104 to 10^6. Melting is modelled using a simplified binary solid solution with linearly depth dependent solidus and liquidus temperatures, as well as a solidus temperature depending linearly on depletion. Starting from a plume free initial temperature condition (to avoid melting at the onset time) five cases are investigated: Case 1 includes melting, but without thermal or dynamic feedback on the convection flow. This case provides a total melt generation rate (qm) in a steady state. Case 2 is identical to case 1 except that latent heat is switched on. Case 3 includes batch melting, melt buoyancy (melt Rayleigh number Rm) and depletion buoyancy, but no melt percolation. Output quantities are the Nusselt number (Nu), root mean square velocity (vrms), the maximum and the total melt volume and qm approaching a statistical steady state. Case 4 includes two-phase flow, i.e. melt percolation, assuming a constant shear and bulk viscosity of the matrix and various melt retention numbers (Rt). These cases are carried out using the Compaction Boussinseq Approximation (Schmeling, 2000) or the full compaction formulation. For cases 1 - 3 very good agreement

  12. Testing of the KRI-developed Silicon PIN Radioxenon Detector

    Energy Technology Data Exchange (ETDEWEB)

    Foxe, Michael P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McIntyre, Justin I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-01-23

    Radioxenon detectors are used for the verification of the Comprehensive Nuclear-Test-Ban Treaty (CTBT) in a network of detectors throughout the world called the International Monitoring System (IMS). The Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) Provisional Technical Secretariat (PTS) has tasked Pacific Northwest National Laboratory (PNNL) with testing a V.G. Khlopin Radium Institute (KRI) and Lares Ltd-developed Silicon PIN detector for radioxenon detection. PNNL measured radioxenon with the silicon PIN detector and determined its potential compared to current plastic scintillator beta cells. While the PNNL tested Si detector experienced noise issues, a second detector was tested in Russia at Lares Ltd, which did not exhibit the noise issues. Without the noise issues, the Si detector produces much better energy resolution and isomer peak separation than a conventional plastic scintillator cell used in the SAUNA systems in the IMS. Under the assumption of 1 cm3 of Xe in laboratory-like conditions, 24-hr count time (12-hr count time for the SAUNA), with the respective shielding the minimum detectable concentrations for the Si detector tested by Lares Ltd (and a conventional SAUNA system) were calculated to be: 131mXe – 0.12 mBq/m3 (0.12 mBq/m3); 133Xe – 0.18 mBq/m3 (0.21 mBq/m3); 133mXe – 0.07 mBq/m3 (0.15 mBq/m3); 135Xe – 0.45 mBq/m3 (0.67 mBq/m3). Detection limits, which are one of the important factors in choosing the best detection technique for radioxenon in field conditions, are significantly better than for SAUNA-like detection systems for 131mXe and 133mXe, but similar for 133Xe and 135Xe. Another important factor is the amount of “memory effect” or carry over signal from one radioxenon measurement to the subsequent sample. The memory effect is

  13. Dimensional changes in FFTF (Fast Flux Test Facility) austenitic cladding and ducts

    Energy Technology Data Exchange (ETDEWEB)

    Makenas, B J; Chastain, S A; Gneiting, B C

    1990-11-01

    As the standard cladding and duct material for the Fast Flux Test Facility driver fuel, 20% cold-worked 316 stainless steel has provided good service up to a fast fluence of 16 {times} 10{sup 22} n/cm{sup 2} in extreme cases. The titanium-stabilized variant of 316 SS, called D9, has extended the useful life of the austenitic alloys by increasing the incubation fluence necessary for the onset of volumetric swelling. Duct flat-to-flat, length and bow, pin bundle distortion, fuel pin diameter and length, as well as cladding volumetric swelling have been examined for high fluence components representing both alloys. These data emphasize the importance of the swelling process, the superiority of D9, and the interrelation between deformations in the duct, bundle, and individual pins. 8 refs., 10 figs.

  14. Cyclohexyl Ketone Inhibitors of Pin1 Dock in a Trans-Diaxial Cyclohexane Conformation

    Science.gov (United States)

    Xu, Guoyan G.; Slebodnick, Carla; Etzkorn, Felicia A.

    2012-01-01

    Cyclohexyl ketone substrate analogue inhibitors (Ac–pSer-Ψ[C = OCH]-Pip–tryptamine) of Pin1, the cell cycle regulatory peptidyl-prolyl isomerase (PPIase), were designed and synthesized as potential electrophilic acceptors for the Pin1 active site Cys113 nucleophile to test a proposed nucleophilic addition-isomerization mechanism. Because they were weak inhibitors, models of all three stereoisomers were docked into the active site of Pin1. Each isomer consistently minimized to a trans-diaxial cyclohexane conformation. From this, we hypothesize that Pin1 stretches substrates into a trans-pyrrolidine conformation to lower the barrier to isomerization. Our reduced amide inhibitor of Pin1 adopted a similar trans-pyrrolidine conformation in the crystal structure. The molecular model of 1, which mimics the l-Ser-l-Pro stereochemistry, in the Pin1 active site showed a distance of 4.4 Å, and an angle of 31° between Cys113-S and the ketone carbon. The computational models suggest that the mechanism of Pin1 PPIase is not likely to proceed through nucleophilic addition. PMID:23028504

  15. Cyclohexyl ketone inhibitors of Pin1 dock in a trans-diaxial cyclohexane conformation.

    Directory of Open Access Journals (Sweden)

    Guoyan G Xu

    Full Text Available Cyclohexyl ketone substrate analogue inhibitors (Ac-pSer-Ψ[C = OCH]-Pip-tryptamine of Pin1, the cell cycle regulatory peptidyl-prolyl isomerase (PPIase, were designed and synthesized as potential electrophilic acceptors for the Pin1 active site Cys113 nucleophile to test a proposed nucleophilic addition-isomerization mechanism. Because they were weak inhibitors, models of all three stereoisomers were docked into the active site of Pin1. Each isomer consistently minimized to a trans-diaxial cyclohexane conformation. From this, we hypothesize that Pin1 stretches substrates into a trans-pyrrolidine conformation to lower the barrier to isomerization. Our reduced amide inhibitor of Pin1 adopted a similar trans-pyrrolidine conformation in the crystal structure. The molecular model of 1, which mimics the l-Ser-l-Pro stereochemistry, in the Pin1 active site showed a distance of 4.4 Å, and an angle of 31° between Cys113-S and the ketone carbon. The computational models suggest that the mechanism of Pin1 PPIase is not likely to proceed through nucleophilic addition.

  16. Load monitoring of pin-connected structures using piezoelectric impedance measurement

    Science.gov (United States)

    Liang, Yabin; Li, Dongsheng; Parvasi, Seyed Mohammad; Song, Gangbing

    2016-10-01

    This paper presents a feasibility study on a developed impedance-based technique using Lead Zirconate Titanate patches for load monitoring of pin-connected structures, which are widely used in construction industry. The basic principle behind the load-monitoring technique is to utilize a high-frequency excitation signal (typically >30 kHz) through a surface-bonded piezoelectric sensor/actuator to detect changes in mechanical impedance of the structure due to the variations in structural loads. In order to verify the effectiveness of the developed technique, a tension-controllable structure with a pin connection was fabricated and investigated in this study. A load monitoring index was used to correlate the dominating peak frequency of the real part of the electrical impedance signature to the pin connection load. Experimental results obtained from twenty repeated tests prove that the proposed load-monitoring index increases as the load on the pin connection increases due to the enlarging true contact area of the pin connection. A 3D finite element method was also used to simulate and analyze the impedance signature of a pin connection model. Very good agreement exists between the numerical simulation’s results and the experimental results which demonstrates that the impedance-based technique can successfully be used to monitor the loading status of pin connections in practical applications.

  17. Closed-Loop Control System for Friction Stir Welding Retractable Pin Tool

    Science.gov (United States)

    Ding, R. Jeffrey; Romine, Peter L.; Munafo, Paul M. (Technical Monitor)

    2001-01-01

    NASA invention disclosure, NASA Case No. MFS-31413, entitled "System for Controlling the Stirring Pin of a Friction Stir Welding Apparatus", (Patent Pending) authored by Jeff Ding, Dr Peter Romine and Pete Oelgoetz, addresses the precision control of the friction stir welding process. The closed-loop control system automatically adjusts the spinning welding pin, real-time, to maintain a precise penetration ligament (i.e., distance between pin-tip and weld panel backside surface). A specific pin length can be maintained while welding constant thickness or tapered material thickness weld panels. The closed-loop control system provides operator data and information relative to the exact position of the welding pin inside the weld joint. This paper presents the closed-loop RPT control system that operates using the auto-feedback of force signals sensed by the tip and shoulder of the welding pin. Significance: The FSW process can be successfully used in a production environment only if there is a method or technique that informs the FSW operator the precise location of the welding pin inside the weld joint. This is essential for applications in aerospace, automotive, pressure vessel, commercial aircraft and other industries.

  18. Experimental study of the mechanical behaviour of pin reinforced foam core sandwich materials under shear load

    Science.gov (United States)

    Dimassi, M. A.; Brauner, C.; Herrmann, A. S.

    2016-03-01

    Sandwich structures with a lightweight closed cell hard foam core have the potential to be used in primary structures of commercial aircrafts. Compared to honeycomb core sandwich, the closed cell foam core sandwich overcomes the issue of moisture take up and makes the manufacturing of low priced and highly integrated structures possible. However, lightweight foam core sandwich materials are prone to failure by localised external loads like low velocity impacts. Invisible cracks could grow in the foam core and threaten the integrity of the structure. In order to enhance the out-of-plane properties of foam core sandwich structures and to improve the damage tolerance (DT) dry fibre bundles are inserted in the foam core. The pins are infused with resin and co-cured with the dry fabric face sheets in an out-of-autoclave process. This study presents the results obtained from shear tests following DIN 53294-standard, on flat sandwich panels. All panels were manufactured with pin-reinforcement manufactured with the Tied Foam Core Technology (TFC) developed by Airbus. The effects of pin material (CFRP and GFRP) and pin volume fraction on the shear properties of the sandwich structure and the crack propagation were investigated and compared to a not pinned reference. It has been concluded that the pin volume fraction has a remarkable effect on the shear properties and damage tolerance of the observed structure. Increasing the pin volume fraction makes the effect of crack redirection more obvious and conserves the integrity of the structure after crack occurrence.

  19. Down-regulation of Pin1 in Temporal Lobe Epilepsy Patients and Mouse Model.

    Science.gov (United States)

    Tang, Lan; Zhang, Yanke; Chen, Guojun; Xiong, Yan; Wang, Xuefeng; Zhu, Binglin

    2017-02-27

    Peptidyl-prolyl cis-trans isomerase NIMA-interacting 1 (Pin1) is a unique PPIase belonging to the parvulin family, and it isomerizes peptide bond between phospho-(Ser/Thr) and Pro. Pin1 has been linked to the pathogenesis of various human diseases; however, its exact biological functions remain unclear. The aim of the present study is to explore the expression pattern of Pin1 in patients with refractory epilepsy and in a chronic pilocarpine-induced epileptic mouse model. Using Western blot, immunofluorescence and immunoprecipitation analysis, we found that Pin1 protein was mainly distributed in neurons, demonstrated by colocalization with the dendritic marker, MAP2. However, the expression of Pin1 decreased remarkably in epileptic patients and experimental mice. Furthermore, the reciprocal coimmunoprecipitation analysis showed that Pin1 interacted with NR2A and NR2B-containing NMDA receptors not AMPA receptors in epileptic mouse models. Our results are the first to indicate that the expression of Pin1 in epileptic brain tissue could play important roles in epilepsy.

  20. Bubble Formation in Basalt-like Melts

    DEFF Research Database (Denmark)

    Jensen, Martin; Keding, Ralf; Yue, Yuanzheng

    2011-01-01

    The effect of the melting temperature on bubble size and bubble formation in an iron bearing calcium aluminosilicate melt is studied by means of in-depth images acquired by optical microscopy. The bubble size distribution and the total bubble volume are determined by counting the number of bubble...

  1. Bubble Formation in Basalt-like Melts

    DEFF Research Database (Denmark)

    Jensen, Martin; Keding, Ralf; Yue, Yuanzheng

    2011-01-01

    The effect of the melting temperature on bubble size and bubble formation in an iron bearing calcium aluminosilicate melt is studied by means of in-depth images acquired by optical microscopy. The bubble size distribution and the total bubble volume are determined by counting the number of bubbles...

  2. Disordering and Melting of Aluminum Surfaces

    DEFF Research Database (Denmark)

    Stoltze, Per; Nørskov, Jens Kehlet; Landman, U.

    1988-01-01

    We report on a molecular-dynamics simulation of an Al(110) surface using the effective-medium theory to describe the interatomic interactions. The surface region is found to start melting ≅200 K below the bulk melting temperature with a gradual increase in the thickness of the disordered layer as...

  3. Uniaxial Elongational viscosity of bidisperse polystyrene melts

    DEFF Research Database (Denmark)

    Nielsen, Jens Kromann; Rasmussen, Henrik K.; Hassager, Ole

    2006-01-01

    The startup and steady uniaxial elongational viscosity have been measured for three bidisperse polystyrene (PS) melts, consisting of blends of monodisperse PS with molecular weights of 52 kg/mole or 103 kg/mole and 390 kg/mole. The bidisperse melts have a maximum in the steady elongational...

  4. Uniaxial Elongational viscosity of bidisperse polystyrene melts

    DEFF Research Database (Denmark)

    Nielsen, Jens Kromann; Rasmussen, Henrik K.; Hassager, Ole

    2006-01-01

    The startup and steady uniaxial elongational viscosity have been measured for three bidisperse polystyrene (PS) melts, consisting of blends of monodisperse PS with molecular weights of 52 kg/mole or 103 kg/mole and 390 kg/mole. The bidisperse melts have a maximum in the steady elongational viscos...

  5. Stability of foams in silicate melts

    Science.gov (United States)

    Proussevitch, Alexander A.; Sahagian, Dork L.; Kutolin, Vladislav A.

    1993-12-01

    Bubble coalescence and the spontaneous disruption of high-porosity foams in silicate melts are the result of physical expulsion of interpore melt (syneresis) leading to bubble coalescence, and diffusive gas exchange between bubbles. Melt expulsion can be achieved either along films between pairs of bubbles, or along Plateau borders which represent the contacts between 3 or more bubbles. Theoretical evaluation of these mechanisms is confirmed by experimental results, enabling us to quantify the relevant parameters and determine stable bubble size and critical film thickness in a foam as a function of melt viscosity, surface tension, and time. Foam stability is controlled primarily by melt viscosity and time. Melt transport leading to coalescence of bubbles proceeds along inter-bubble films for smaller bubbles, and along Plateau borders for larger bubbles. Thus the average bubble size accelerates with time. In silicate melts, the diffusive gas expulsion out of a region of foam is effective only for water (and even then, only at small length scales), as the diffusion of CO 2 is negligible. The results of our analyses are applicable to studies of vesicularity of lavas, melt degassing, and eruption mechanisms.

  6. Purification of Niobium by Electron Beam Melting

    Science.gov (United States)

    Sankar, M.; Mirji, K. V.; Prasad, V. V. Satya; Baligidad, R. G.; Gokhale, A. A.

    2016-06-01

    Pure niobium metal, produced by alumino-thermic reduction of niobium oxide, contains various impurities which need to be reduced to acceptable levels to obtain aerospace grade purity. In the present work, an attempt has been made to refine niobium metals by electron beam drip melting technique to achieve purity confirming to the ASTM standard. Input power to the electron gun and melt rate were varied to observe their combined effect on extend of refining and loss of niobium. Electron beam (EB) melting is shown to reduce alkali metals, trace elements and interstitial impurities well below the specified limits. The reduction in the impurities during EB melting is attributed to evaporation and degassing due to the combined effect of high vacuum and high melt surface temperature. The % removal of interstitial impurities is essentially a function of melt rate and input power. As the melt rate decreases or input power increases, the impurity levels in the solidified niobium ingot decrease. The EB refining process is also accompanied by considerable amount of niobium loss, which is attributed to evaporation of pure niobium and niobium sub-oxide. Like other impurities, Nb loss increases with decreasing melt rate or increase in input power.

  7. Shock-induced melting and rapid solidification

    Energy Technology Data Exchange (ETDEWEB)

    Nellis, W.J.; Gourdin, W.H.; Maple, M.B.

    1987-08-01

    Model calculations are presented to estimate that approx.50 GPa is required to completely shock melt metal powders with quenching at rates up to 10/sup 8/ K/s. Experiments are discussed for powders of a Cu-Zr alloy compacted in the usual way at 16 GPa and melted by shocking to 60 GPa. 12 refs.

  8. Effect of pinning and driving force on the metastability effects in weakly pinned superconductors and the determination of spinodal line pertaining to order-disorder transition

    Indian Academy of Sciences (India)

    A D Thakur; S S Banerjee; M J Higgins; S Ramakrishnan; A K Grover

    2006-01-01

    We explore the effect of varying drive on metastability features exhibited by the vortex matter in single crystals of 2H-NbSe2 and CeRu2 with varying degree of random pinning. The metastable nature of vortex matter is reflected in the path dependence of the critical current density, which in turn is probed in a contact-less way via AC-susceptibility measurements. The sinusoidal AC magnetic field applied during AC susceptibility measurements appears to generate a driving force on the vortex matter. In a nascent pinned single crystal of 2H-NbSe2, where the peak effect (PE) pertaining to the order-disorder phenomenon is a sharp first-order-like transition, the supercooling feature below the peak temperature is easily wiped out by the reorganization caused by the AC driving force. In this paper, we elucidate the interplay between the drive and the pinning which can conspire to make the path-dependent AC-susceptibility response of different metastable vortex states appear identical. An optimal balance between the pinning and driving force is needed to view the metastability effects in typically weakly pinned specimen of low temperature superconductors. As one uses samples with larger pinning in order to differentiate the response of different metastable vortex states, one encounters a new phenomenon, viz., the second magnetization peak (SMP) anomaly prior to the PE. Supercooling/superheating can occur across both the PE and the SMP anomalies and both of these are known to display non-linear characteristics as well. Interplay between the path dependence in the critical current density and the non-linearity in the electromagnetic response determine the metastability effects seen in the first and the third harmonic response of the AC susceptibility across the temperature regions of the SMP and the PE. The limiting temperature above which metastability effects cease can be conveniently located in the third harmonic data, and the observed behavior can be rationalized within

  9. Outcome after pin fixation of supracondylar humerus fractures in children: postoperative radiographic examinations are unnecessary

    Science.gov (United States)

    Tuomilehto, Noora; Kivisaari, Reetta; Sommarhem, Antti; Nietosvaara, Aarno Y

    2017-01-01

    Background and purpose — The quality of pin fixation of displaced supracondylar humerus fractures in children has not been assessed, and the clinical value of radiographic examinations after pin fixation is unclear. We evaluated pin configuration, quality of osteosynthesis, and outcome in 264 supracondylar fractures. The clinical significance of postoperative radiographs was analyzed. Patients and methods — 252 Gartland-III and 12 flexion-type supracondylar humerus fractures were pin-fixed in the periods 2002–2006 and 2012–2014. During 2012–2014, staff were intructed that postoperative radiographs should not be taken. Quality of reduction was assessed by measuring Baumann and lateral capitellohumeral angles (LCHA) and also by recording the crossing point of the anterior humeral line (AHL) with bony capitellum. Rotatory alignment was registered as normal or abnormal. Pin configuration and quality of osteosynthesis were evaluated. The clinical significance of postoperative radiographs was analyzed. Results — Postoperatively, Baumann angle was normal in 66% of the fractures, AHL crossed the capitellum in 84%, and no malrotation was evident in 85% of the fractures. Crossed pins were used in 89% of the cases. 2 or more pins fixed both fracture fragments in 66%. Radiographic examinations were inadequate for assessment of LCHA in 13%, of Bauman angle in 8%, of AHL in 2%, of rotation in 1%, and of pin fixation in 2% of the cases. Postoperative radiographs did not give useful information except in 1 patient who had corrective osteotomy. All 94 patients with follow-up (97%) who were treated during 2012–2014 were satisfied with the outcome. Interpretation — Despite pin fixation being deemed unsatisfactory in one-third of the cases, significant malunion was rare. Postoperative radiography did not alter management or outcome. PMID:27774833

  10. Electron holography on remanent magnetization distribution of melt-spun Nd-Fe-B magnets.

    Science.gov (United States)

    Park, Young-Gil; Shindo, Daisuke

    2004-01-01

    Microstructures and magnetic domain structures of melt-spun Nd-Fe-B permanent magnets were investigated in detail by analytical electron microscopy and electron holography. While the crystal orientation of matrix Nd2Fe14B grains was analyzed by nanobeam electron diffraction, precipitates of a few tens of nanometers at grain boundaries were identified to be alpha-Fe by energy-dispersive X-ray spectroscopy. The detailed magnetization distribution in Nd2Fe14B grains and at their boundaries was visualized by electron holography. Ex situ experimentation with an electromagnet revealed that the domain walls in the demagnetized state and remanent states were pinned at grain boundaries, and Fe precipitates at the grain boundary were situated at the center of the closure domain.

  11. Forming of High-strength Steels Using a Hot-melt Dry Lubricant

    DEFF Research Database (Denmark)

    Hörnström, Sven-Erik; Karlsson, Erik; Olsson, Mikael

    2008-01-01

    steel grades and improved surface engineering treatments such as the deposition of low friction CVD and PVD coatings. In the present study the performance of a hot-melt dry lubricant in the forming of hot and cold rolled and hot-dip galvanized high strength steel has been evaluated and compared...... with a conventional rust protection oil using four different tests methods, i.e. a strip reduction test, a bending under tension test, a stretch-forming test and a pin-on disc test. In the tests, two different cold work tool steels, a conventional steel grade and a nitrogen alloyed PM steel grade were evaluated......The increasing use of high strength steels in a variety of mechanical engineering applications has illuminated problems associated with galling in sheet metal forming operations. Galling is a tribological phenomenon associated with transfer of material from the steel sheet to the tool surface...

  12. Size-dependent melting of Bi nanoparticles

    Science.gov (United States)

    Olson, E. A.; Efremov, M. Yu.; Zhang, M.; Zhang, Z.; Allen, L. H.

    2005-02-01

    Nanocalorimetry was used to investigate the melting of Bi nanoparticles. The particles were formed by evaporating Bi onto a silicon nitride substrate, which was then heated. The particles self-assemble into truncated spherical particles. Below 5-nm average film thickness, mean particle sizes increased linearly with deposition thickness but increased rapidly for 10-nm-thick films. As expected, small particles were found to exhibit size-dependent melting temperatures less than the bulk melting temperature (e.g., ΔT =67K for a 3-nm radius particle). The measured melting temperatures for particles below ˜7nm in radius, however, were ˜50K above the value predicted by the homogeneous melting model. We discuss this discrepancy in terms of a possible size-dependent crystal structure change and the superheating of the solid phase.

  13. Nanotexturing of surfaces to reduce melting point.

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Ernest J.; Zubia, David (University of Texas at El Paso El Paso, TX); Mireles, Jose (Universidad Aut%C3%94onoma de Ciudad Ju%C3%94arez Ciudad Ju%C3%94arez, Mexico); Marquez, Noel (University of Texas at El Paso El Paso, TX); Quinones, Stella (University of Texas at El Paso El Paso, TX)

    2011-11-01

    This investigation examined the use of nano-patterned structures on Silicon-on-Insulator (SOI) material to reduce the bulk material melting point (1414 C). It has been found that sharp-tipped and other similar structures have a propensity to move to the lower energy states of spherical structures and as a result exhibit lower melting points than the bulk material. Such a reduction of the melting point would offer a number of interesting opportunities for bonding in microsystems packaging applications. Nano patterning process capabilities were developed to create the required structures for the investigation. One of the technical challenges of the project was understanding and creating the specialized conditions required to observe the melting and reshaping phenomena. Through systematic experimentation and review of the literature these conditions were determined and used to conduct phase change experiments. Melting temperatures as low as 1030 C were observed.

  14. Comparison between a silicon PIN diode and a CsI(Tl) coupled to a silicon PIN diode for dosimetric purpose in radiology

    Science.gov (United States)

    Andreani, Lucia; Bontempi, Marco; Rossi, Pier Luca; Rignanese, Luigi Pio; Zuffa, Mirco; Baldazzi, Giuseppe

    2014-10-01

    The use of amorphous Si-PIN diodes showed interesting applications in detector research. Due to their properties and cost effective value, these devices can be used as small dosimeters for fast and real time dose evaluation. The responses of two different detectors to the measurement of X-ray total air KERMA are compared and presented, with the goal to get a dosimetric parameter directly during the X-ray patients exposure. A bare Si-PIN diode and a Si-PIN diode+CsI(Tl) scintillator were tested and compared to radiologic dosimeters. Both detector outputs were calibrated using a secondary reference standard (CAPINTEC PM 30 dosimeter), in order to analyze and discuss the dose and the energy dependence of the detectors in the range of radiologic interest (tube voltage: 40-140 kVp and additional filtration: 0 mm Al to 4 mm Al). The bare Si-PIN diode shows a very coherent response independently from the X-ray beam quality and from the additional filtration. The Si-PIN+CsI(Tl) detector, on the other hand, shows a high spread of the calibration curves as a function of the tube high voltage and the additional filtration. The presented results could be used to calibrate an image detector in dose.

  15. Comparison between a silicon PIN diode and a CsI(Tl) coupled to a silicon PIN diode for dosimetric purpose in radiology

    Energy Technology Data Exchange (ETDEWEB)

    Andreani, Lucia, E-mail: lucia.andreani4@unibo.it [University of Bologna, Department of Physics and Astronomy, Viale Berti-Pichat 6/2, 40127 Bologna (Italy); INFN Bologna, Viale Berti Pichat 6/2, 40127 Bologna (Italy); Bontempi, Marco [Laboratorio NaBi, Istituto Ortopedico Rizzoli, via di Barbiano 1/10, 40136 Bologna (Italy); Rossi, Pier Luca [University of Bologna, Department of Physics and Astronomy, Viale Berti-Pichat 6/2, 40127 Bologna (Italy); INFN Bologna, Viale Berti Pichat 6/2, 40127 Bologna (Italy); Rignanese, Luigi Pio [University of Bologna, Department of Physics and Astronomy, Viale Berti-Pichat 6/2, 40127 Bologna (Italy); Zuffa, Mirco [INFN Bologna, Viale Berti Pichat 6/2, 40127 Bologna (Italy); Baldazzi, Giuseppe [University of Bologna, Department of Physics and Astronomy, Viale Berti-Pichat 6/2, 40127 Bologna (Italy); INFN Bologna, Viale Berti Pichat 6/2, 40127 Bologna (Italy)

    2014-10-21

    The use of amorphous Si-PIN diodes showed interesting applications in detector research. Due to their properties and cost effective value, these devices can be used as small dosimeters for fast and real time dose evaluation. The responses of two different detectors to the measurement of X-ray total air KERMA are compared and presented, with the goal to get a dosimetric parameter directly during the X-ray patients exposure. A bare Si-PIN diode and a Si-PIN diode+CsI(Tl) scintillator were tested and compared to radiologic dosimeters. Both detector outputs were calibrated using a secondary reference standard (CAPINTEC PM 30 dosimeter), in order to analyze and discuss the dose and the energy dependence of the detectors in the range of radiologic interest (tube voltage: 40–140 kVp and additional filtration: 0 mm Al to 4 mm Al). The bare Si-PIN diode shows a very coherent response independently from the X-ray beam quality and from the additional filtration. The Si-PIN+CsI(Tl) detector, on the other hand, shows a high spread of the calibration curves as a function of the tube high voltage and the additional filtration. The presented results could be used to calibrate an image detector in dose.

  16. Volatile diffusion in silicate melts and its effects on melt inclusions

    Directory of Open Access Journals (Sweden)

    P. Scarlato

    2005-06-01

    Full Text Available A compendium of diffusion measurements and their Arrhenius equations for water, carbon dioxide, sulfur, fluorine, and chlorine in silicate melts similar in composition to natural igneous rocks is presented. Water diffusion in silicic melts is well studied and understood, however little data exists for melts of intermediate to basic compositions. The data demonstrate that both the water concentration and the anhydrous melt composition affect the diffusion coefficient of water. Carbon dioxide diffusion appears only weakly dependent, at most, on the volatilefree melt composition and no effect of carbon dioxide concentration has been observed, although few experiments have been performed. Based upon one study, the addition of water to rhyolitic melts increases carbon dioxide diffusion by orders of magnitude to values similar to that of 6 wt% water. Sulfur diffusion in intermediate to silicic melts depends upon the anhydrous melt composition and the water concentration. In water-bearing silicic melts sulfur diffuses 2 to 3 orders of magnitude slower than water. Chlorine diffusion is affected by both water concentration and anhydrous melt composition; its values are typically between those of water and sulfur. Information on fluorine diffusion is rare, but the volatile-free melt composition exerts a strong control on its diffusion. At the present time the diffusion of water, carbon dioxide, sulfur and chlorine can be estimated in silicic melts at magmatic temperatures. The diffusion of water and carbon dioxide in basic to intermediate melts is only known at a limited set of temperatures and compositions. The diffusion data for rhyolitic melts at 800°C together with a standard model for the enrichment of incompatible elements in front of growing crystals demonstrate that rapid crystal growth, greater than 10-10 ms-1, can significantly increase the volatile concentrations at the crystal-melt interface and that any of that melt trapped

  17. Partitioning coefficients between olivine and silicate melts

    Science.gov (United States)

    Bédard, J. H.

    2005-08-01

    Variation of Nernst partition coefficients ( D) between olivine and silicate melts cannot be neglected when modeling partial melting and fractional crystallization. Published natural and experimental olivine/liquidD data were examined for covariation with pressure, temperature, olivine forsterite content, and melt SiO 2, H 2O, MgO and MgO/MgO + FeO total. Values of olivine/liquidD generally increase with decreasing temperature and melt MgO content, and with increasing melt SiO 2 content, but generally show poor correlations with other variables. Multi-element olivine/liquidD profiles calculated from regressions of D REE-Sc-Y vs. melt MgO content are compared to results of the Lattice Strain Model to link melt MgO and: D0 (the strain compensated partition coefficient), EM3+ (Young's Modulus), and r0 (the size of the M site). Ln D0 varies linearly with Ln MgO in the melt; EM3+ varies linearly with melt MgO, with a dog-leg at ca. 1.5% MgO; and r0 remains constant at 0.807 Å. These equations are then used to calculate olivine/liquidD for these elements using the Lattice Strain Model. These empirical parameterizations of olivine/liquidD variations yield results comparable to experimental or natural partitioning data, and can easily be integrated into existing trace element modeling algorithms. The olivine/liquidD data suggest that basaltic melts in equilibrium with pure olivine may acquire small negative Ta-Hf-Zr-Ti anomalies, but that negative Nb anomalies are unlikely to develop. Misfits between results of the Lattice Strain Model and most light rare earth and large ion lithophile partitioning data suggest that kinetic effects may limit the lower value of D for extremely incompatible elements in natural situations characterized by high cooling/crystallization rates.

  18. Hysteretic rotational magnetization of pinned layer in NiO spin-valve

    CERN Document Server

    Kim, C G; Hwang, D G; Lee, S S; Kim, C O

    2002-01-01

    The magnetoresistance (MR) curves during the rotation of magnetic field in NiO spin-valve are well described by taking into account the involved magnetization process of free and pinned layers according to rotating field strength. In particular, hysteretic MR characteristics pronounced in a field strength of 1.5 times the exchange field are ascribed for by the viscosity effect on magnetization rotation of pinned layer. These analyses of MR curves provide a basis decomposing the MR components from each magnetization process of free and pinned layers.

  19. Solution structural analysis of the single-domain parvulin TbPin1.

    Directory of Open Access Journals (Sweden)

    Lifang Sun

    Full Text Available BACKGROUND: Pin1-type parvulins are phosphorylation-dependent peptidyl-prolyl cis-trans isomerases. Their functions have been widely reported to be involved in a variety of cellular responses or processes, such as cell division, transcription, and apoptosis, as well as in human diseases including Alzheimer's disease and cancers. TbPin1 was identified as a novel class of Pin1-type parvulins from Trypanosoma brucei, containing a unique PPIase domain, which can catalyze the isomerization of phosphorylated Ser/Thr-Pro peptide bond. METHODOLOGY/PRINCIPAL FINDINGS: We determined the solution structure of TbPin1 and performed (15N relaxation measurements to analyze its backbone dynamics using multi-dimensional heteronuclear NMR spectroscopy. The average RMSD values of the 20 lowest energy structures are 0.50±0.05 Å for backbone heavy atoms and 0.85±0.08 Å for all heavy atoms. TbPin1 adopts the typical catalytic tertiary structure of Pin1-type parvulins, which comprises a globular fold with a four-stranded anti-parallel β-sheet core surrounded by three α-helices and one 3(10-helix. The global structure of TbPin1 is relatively rigid except the active site. The 2D EXSY spectra illustrate that TbPin1 possesses a phosphorylation-dependent PPIase activity. The binding sites of TbPin1 for a phosphorylated peptide substrate {SSYFSG[p]TPLEDDSD} were determined by the chemical shift perturbation approach. Residues Ser15, Arg18, Asn19, Val21, Ser22, Val32, Gly66, Ser67, Met83, Asp105 and Gly107 are involved in substantial contact with the substrate. CONCLUSIONS/SIGNIFICANCE: The solution structure of TbPin1 and the binding sites of the phosphorylated peptide substrate on TbPin1 were determined. The work is helpful for further understanding the molecular basis of the substrate specificity for Pin1-type parvulin family and enzyme catalysis.

  20. Complications Using Bioabsorbable Cross-Pin Femoral Fixation: A Case Report and Review of the Literature

    Directory of Open Access Journals (Sweden)

    Saqib Hasan

    2011-01-01

    Full Text Available The use of bioabsorbable cross-pin transcondylar fixation has remained a viable option for femoral fixation in anterior cruciate ligament reconstruction. Although numerous biomechanical studies have demonstrated high fixation strength and minimal slippage with use of this method of fixation, there have been increasing reports of a variety of clinical complications associated with these implants. We reviewed the literature for all complications associated with the Bio-TransFix implant and present a case report of a patient status after ACL reconstruction using Bio-TransFix cross-pin femoral fixation with iliotibial band friction syndrome from a broken cross-pin four month post-operatively.

  1. Impact of pinning of the triple contact line on electrowetting performance.

    Science.gov (United States)

    Gupta, Rohini; Sheth, Danica M; Boone, Teno K; Sevilla, Arianne B; Fréchette, Joëlle

    2011-12-20

    Pinning of the triple contact line adversely affects electrowetting on dielectric. Electrowetting response of substrates with contact angle hysteresis ranging from 1° to 30° has been characterized, and the results are interpreted within the framework of electromechanics corrected for pinning. The relationship between contact angle hysteresis, threshold potential for liquid actuation, and electrowetting hysteresis is quantified. Our results demonstrate that a modified electrowetting equation, based on balance of forces (including the pinning forces) acting on the triple contact line and on the drop, describes the electrowetting response of substrates with significant contact angle hysteresis. Finally, the surface properties of PDMS Sylgard 184 were found to be influenced by the electric field.

  2. Measurement of contact angle in a clearance-fit pin-loaded hole

    Science.gov (United States)

    Prabhakaran, R.; Naik, R. A.

    1986-01-01

    A technique which measures load-contact variation in a clearance-fit, pin-loaded hole is presented in detail. A steel instrumented pin, which activates a make-or-break electrical circuit in the pin-hole contact region, was inserted into one aluminum and one polycarbonate specimen. The resulting load-contact variations are indicated schematically. The ability to accurately determine the arc of contact at any load was crucial to this measurement. It is noted that this simple experimental technique is applicable to both conducting and nonconducting materials.

  3. Absorption coefficients of GeSn extracted from PIN photodetector response

    Science.gov (United States)

    Ye, Kaiheng; Zhang, Wogong; Oehme, Michael; Schmid, Marc; Gollhofer, Martin; Kostecki, Konrad; Widmann, Daniel; Körner, Roman; Kasper, Erich; Schulze, Jörg

    2015-08-01

    In this paper the optical absorption of the GeSn PIN photodetector was investigated. The vertical GeSn PIN photodetectors were fabricated by molecular beam epitaxy (MBE) and dry etching. By means of current density-voltage (J-V) and capacity-voltage (C-V) measurements the photodetector device was characterized. The absorption coefficients of GeSn material were finally extracted from the optical response of PIN structure. With further direct bandgap analysis the influences of device structure was proved negligible.

  4. Pinning-controlled synchronization of delayed neural networks with distributed-delay coupling via impulsive control.

    Science.gov (United States)

    He, Wangli; Qian, Feng; Cao, Jinde

    2017-01-01

    This paper investigates pinning synchronization of coupled neural networks with both current-state coupling and distributed-delay coupling via impulsive control. A novel impulse pinning strategy involving pinning ratio is proposed and a general criterion is derived to ensure an array of neural networks with two different topologies synchronizes with the desired trajectory. In order to handle the difficulties of high-dimension criteria, some inequality techniques and matrix decomposition methods through simultaneous diagonalization of two matrices are introduced and low-dimensional criteria are obtained. Finally, an illustrative example is given to show the effectiveness of the proposed method. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Synchronization analysis of coloured delayed networks under decentralized pinning intermittent control

    Indian Academy of Sciences (India)

    JIANG SHENGQIN; LU XIAOBO

    2016-06-01

    This paper investigates synchronization of coloured delayed networks under decentralized pinning intermittent control. To begin with, the time delays are taken into account in the coloured networks. In addition, we propose a decentralized pinning intermittent control for coloured delayed networks, which is different from that most of pinning intermittent controls are only appliedto the nodes from 1 to l or centralized nodes. Moreover, sufficient conditions are derived to guarantee the synchronization of coloured delayed networks based on Lyapunov stability theorem. Finally, numerical simulations are provided to verify the validity of the obtained results.

  6. Pinning Control of Lag-Consensus for Second-Order Nonlinear Multiagent Systems.

    Science.gov (United States)

    Wang, Yi; Ma, Zhongjun; Zheng, Song; Chen, Guanrong

    2016-07-29

    Lag consensus means that the corresponding state vectors of the followers are behind the leader with a lag time. In this paper, Lyapunov functional and matrix theory are applied to analyze pinning-controlled lag consensus of second-order nonlinear multiagent systems. The focus is twofold: 1) to find out which agents should be pinned and 2) to determine what the coupling strength should be, so that the multiagent systems can reach lag consensus. Moreover, the practical problem in a noisy environment is considered. Finally, an illustrative example is provided to demonstrate the effectiveness of the proposed pinning control protocol.

  7. Dislocation pinning effects on fracture behavior: Atomistic and dislocation dynamics simulations

    Science.gov (United States)

    Noronha, S. J.; Farkas, D.

    2002-10-01

    We introduce an approach in which results from atomistic simulations are combined with discrete dislocation dynamics simulations of crack-tip plasticity. The method is used to study the effects of dislocation pinning due to grain boundaries or secondary particles on the fracture behavior of aluminum. We find that the fracture resistance is reduced with decreasing pinning distance. The results show that the pinning of the dislocations causes a net decrease in the shear stress projected on the slip plane, preventing further dislocation emission. Semibrittle cleavage occurs after a certain number of dislocations is emitted.

  8. Flux Pinning Effects of Y2O3 Nanoparticulate Dispersions in Multilayered YBCO Thin Films

    Science.gov (United States)

    2012-02-01

    AFRL-RZ-WP-TP-2012-0090 FLUX PINNING EFFECTS OF Y2O3 NANOPARTICULATE DISPERSIONS IN MULTILAYERED YBCO THIN FILMS (POSTPRINT) T.A...January 2005 4. TITLE AND SUBTITLE FLUX PINNING EFFECTS OF Y2O3 NANOPARTICULATE DISPERSIONS IN MULTILAYERED YBCO THIN FILMS (POSTPRINT) 5a...Clearance Date: 06 Dec 2005. 14. ABSTRACT The flux pinning effects of Y2O3 nanoparticulate inclusions in YBa2Cu3O7-δ (Y123 or YBCO ) thin films

  9. Random pinning glass transition: hallmarks, mean-field theory and renormalization group analysis.

    Science.gov (United States)

    Cammarota, Chiara; Biroli, Giulio

    2013-03-28

    We present a detailed analysis of glass transitions induced by pinning particles at random from an equilibrium configuration. We first develop a mean-field analysis based on the study of p-spin spherical disordered models and then obtain the three-dimensional critical behavior by the Migdal-Kadanoff real space renormalization group method. We unveil the important physical differences with the case in which particles are pinned from a random (or very high temperature) configuration. We contrast the pinning particles approach to the ones based on biasing dynamical trajectories with respect to their activity and on coupling to equilibrium configurations. Finally, we discuss numerical and experimental tests.

  10. Cooling system having reduced mass pin fins for components in a gas turbine engine

    Science.gov (United States)

    Lee, Ching-Pang; Jiang, Nan; Marra, John J

    2014-03-11

    A cooling system having one or more pin fins with reduced mass for a gas turbine engine is disclosed. The cooling system may include one or more first surfaces defining at least a portion of the cooling system. The pin fin may extend from the surface defining the cooling system and may have a noncircular cross-section taken generally parallel to the surface and at least part of an outer surface of the cross-section forms at least a quartercircle. A downstream side of the pin fin may have a cavity to reduce mass, thereby creating a more efficient turbine airfoil.

  11. Pinning center evaluation of a YBCO thin film; YBCO hakumaku no pinningu senta hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Michishita, K.; Sasaki, Y.; Higashida, Y.; Kubo, Y. [Japan Fine Ceramics Center, Nagoya (Japan); Nakamura, K. [Nagoya Inst. of Tech., Nagoya (Japan); Takeda, K. [Engineering Research Association for Superconductive Genertion Equipment and Materials, Osaka (Japan)

    1999-06-07

    Line of magnetic flux distribution of YBCO thin film and BSCCO single crystal was evaluated by the Bitter method. Since there is no powerful pinning center, in BSCCO single crystal, which shows low Jc, it is the almost regular line of magnetic flux distribution. For this, in an YBCO thin film which showed high Jc, powerful pinning center such as tilt boundary and heterogenous phase existed, and it was clarified to be the line of magnetic flux distribution without the regularity. This time, an YBCO thin film was evaluated for the purpose of the identification of pinning center. (NEDO)

  12. Calpastatin is regulated by protein never in mitosis gene A interacting-1 (PIN1) in endothelial cells

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Tongzheng, E-mail: liu.tongzheng@mayo.edu [Division of Oncology Research, Department of Oncology, Mayo Clinic, Rochester, MN 55905 (United States); Schneider, Ryan A., E-mail: schneiderr@findlay.edu [College of Pharmacy, The University of Findlay, Findlay, OH 45840 (United States); Hoyt, Dale G., E-mail: hoyt.27@osu.edu [The Dorothy M. Davis Heart and Lung Research Institute, and the Division of Pharmacology, College of Pharmacy, The Ohio State University, 500 West Twelfth Avenue, Columbus, OH 43210 (United States)

    2011-10-28

    Highlights: Black-Right-Pointing-Pointer Depletion of PIN1 increases inhibitory effect of calpastatin against calpain in endothelial cells. Black-Right-Pointing-Pointer PIN1 associates with calpastatin. Black-Right-Pointing-Pointer PIN1, but not mutants, reduces the inhibitory activity of calpastatin in vitro. Black-Right-Pointing-Pointer Depletion of calpastatin shows that it is required for PIN1 depletion to reduce calpain activity. -- Abstract: The peptidyl-proline isomerase, protein never in mitosis gene A interacting-1 (PIN1) binds and isomerizes proteins phosphorylated on serine/threonine before a proline. It was previously found that depletion of PIN1 greatly increased induction of cyclooxygenase-2 and inducible nitric oxide synthase by lowering calpain activity in murine aortic endothelial cells (MAEC). Here we investigated the effect of PIN1 on the endogenous inhibitor of heterodimeric {mu}- and m-calpains, calpastatin. MAEC were transduced with small hairpin (sh) RNA to knock down PIN1 (KD) or an inactive Control shRNA. Cells were also treated with non-targeted double stranded small inhibitory RNA (siRNA) or siRNA designed to deplete calpastatin. Despite reducing calpain activity, PIN1 KD did not significantly affect the expression of {mu}- and m-calpains, or calpastatin, compared to Control shRNA. Instead, depletion of PIN1 increased the inhibitory activity of calpastatin. Calpastatin co-immunoprecipitated with endogenous PIN1 and was pulled down with glutathione-S-transferase (GST)-PIN1 fusion protein. Adding GST-PIN1 to KD cell extracts lacking PIN1 reduced calpastatin inhibitory activity. Substrate binding and catalytic domain mutants of PIN1 failed to do so. These results suggest that protein interaction and the proline isomerase functions of PIN1 are required for it to inhibit calpastatin. Furthermore, depletion of calpastatin raised calpain activity and reduced calpain inhibitory activity to similar levels in KD and Control MAEC, indicating that

  13. North Slope, Alaska ESI: FACILITY (Facility Points)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains data for oil field facilities for the North Slope of Alaska. Vector points in this data set represent oil field facility locations. This data...

  14. Waste Management Facilities Cost Information Report

    Energy Technology Data Exchange (ETDEWEB)

    Feizollahi, F.; Shropshire, D.

    1992-10-01

    The Waste Management Facility Cost Information (WMFCI) Report, commissioned by the US Department of Energy (DOE), develops planning life-cycle cost (PLCC) estimates for treatment, storage, and disposal facilities. This report contains PLCC estimates versus capacity for 26 different facility cost modules. A procedure to guide DOE and its contractor personnel in the use of estimating data is also provided. Estimates in the report apply to five distinctive waste streams: low-level waste, low-level mixed waste, alpha contaminated low-level waste, alpha contaminated low-level mixed waste, and transuranic waste. The report addresses five different treatment types: incineration, metal/melting and recovery, shredder/compaction, solidification, and vitrification. Data in this report allows the user to develop PLCC estimates for various waste management options.

  15. Waste Management Facilities Cost Information Report

    Energy Technology Data Exchange (ETDEWEB)

    Feizollahi, F.; Shropshire, D.

    1992-10-01

    The Waste Management Facility Cost Information (WMFCI) Report, commissioned by the US Department of Energy (DOE), develops planning life-cycle cost (PLCC) estimates for treatment, storage, and disposal facilities. This report contains PLCC estimates versus capacity for 26 different facility cost modules. A procedure to guide DOE and its contractor personnel in the use of estimating data is also provided. Estimates in the report apply to five distinctive waste streams: low-level waste, low-level mixed waste, alpha contaminated low-level waste, alpha contaminated low-level mixed waste, and transuranic waste. The report addresses five different treatment types: incineration, metal/melting and recovery, shredder/compaction, solidification, and vitrification. Data in this report allows the user to develop PLCC estimates for various waste management options.

  16. ODS Ferritic/martensitic alloys for Sodium Fast Reactor fuel pin cladding

    Science.gov (United States)

    Dubuisson, Philippe; Carlan, Yann de; Garat, Véronique; Blat, Martine

    2012-09-01

    The development of ODS materials for the cladding for Sodium Fast Reactors is a key issue to achieve the objectives required for the GEN IV reactors. CEA, AREVA and EDF have launched in 2007 an important program to determine the optimal fabrication parameters, and to measure and understand the microstructure and properties before, under and after irradiation of such cladding materials. The aim of this paper is to present the French program and the major results obtained recently at CEA on Fe-9/14/18Cr1WTiY2O3 ferritic/martensitic ODS materials. The first step of the program was to consolidate Fe-9/14/18Cr ODS materials as plates and bars to study the microstructure and the mechanical properties of the new alloys. The second step consists in producing tubes at a geometry representative of the cladding of new Sodium Fast Reactors. The optimization of the fabrication route at the laboratory scale is conducted and different tubes were produced. Their microstructure depends on the martensitic (Fe-9Cr) or ferritic (Fe-14Cr) structure. To join the plug to the tube, the reference process is the welding resistance. A specific approach is developed to model the process and support the development of the welds performed within the "SOPRANO" facility. The development at CEA of Fe-9/14/18Cr new ODS materials for the cladding for GENIV Sodium Fast Reactors is in progress. The first microstructural and mechanical characterizations are very encouraging and the full assessment and qualification of this new alloys and products will pass through the irradiation of specimens, tubes, fuel pins and subassemblies up to high doses.

  17. Development and Assessment of CTF for Pin-resolved BWR Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Salko, Robert K [ORNL; Wysocki, Aaron J [ORNL; Collins, Benjamin S [ORNL; Avramova, Maria [North Carolina State University (NCSU), Raleigh; Gosdin, Chris [Pennsylvania State University

    2017-01-01

    CTF is the modernized and improved version of the subchannel code, COBRA-TF. It has been adopted by the Consortium for Advanced Simulation for Light Water Reactors (CASL) for subchannel analysis applications and thermal hydraulic feedback calculations in the Virtual Environment for Reactor Applications Core Simulator (VERA-CS). CTF is now jointly developed by Oak Ridge National Laboratory and North Carolina State University. Until now, CTF has been used for pressurized water reactor modeling and simulation in CASL, but in the future it will be extended to boiling water reactor designs. This required development activities to integrate the code into the VERA-CS workflow and to make it more ecient for full-core, pin resolved simulations. Additionally, there is a significant emphasis on producing high quality tools that follow a regimented software quality assurance plan in CASL. Part of this plan involves performing validation and verification assessments on the code that are easily repeatable and tied to specific code versions. This work has resulted in the CTF validation and verification matrix being expanded to include several two-phase flow experiments, including the General Electric 3 3 facility and the BWR Full-Size Fine Mesh Bundle Tests (BFBT). Comparisons with both experimental databases is reasonable, but the BFBT analysis reveals a tendency of CTF to overpredict void, especially in the slug flow regime. The execution of these tests is fully automated, analysis is documented in the CTF Validation and Verification manual, and the tests have become part of CASL continuous regression testing system. This paper will summarize these recent developments and some of the two-phase assessments that have been performed on CTF.

  18. Melt and Chemical Transport in the Mantle: Insights from Deglaciation-Induced Melting Perturbations in Iceland

    Science.gov (United States)

    Eason, D. E.; Ito, G.; Sinton, J. M.

    2011-12-01

    Eruptive products represent a time-averaged view of the melting region and melt migration processes, making numerous fundamental parameters of the melt system difficult to constrain. Temporal and spatial variations in melting provide potential windows into this obscure region of the Earth by preferentially sampling melts from different regions of the mantle or mixing melts over different length-scales. We present a newly extended geochemical time series from the Western Volcanic Zone (WVZ) of Iceland, which experienced a short-lived melting perturbation due to glacial unloading during the last major deglaciation (~15-10 ka). Glacial unloading during this period led to increased degrees of melting particularly in the shallow mantle, which is manifest as an observed increase in volcanic production up to 30 times the steady-state value, decreased levels of highly to moderately incompatible element ratios (e.g., a 35-50% decrease in Nb/Y, with the greatest change occurring in the northernmost WVZ), and elevated SiO2 and CaO concentrations (~0.8 wt. % and ~1.9 wt. % increase in average oxide concentrations respectively) during and immediately following deglaciation. Although eruptive productivity returns to steady-state values within ~3000 yr following deglaciation, the incompatible element concentrations in erupted lavas gradually increase throughout the post-glacial period. We exploit this short-lived melting perturbation to examine and constrain knowledge of fundamental characteristics of melt generation and transport, including mantle permeability, melt ascent rates, depth-dependent melting functions (dF/dP), and the nature of chemical transport and melt mixing in the system. Using conservation equations describing the generation and porous flow of melt in a viscous matrix, we model melt migration in the mantle during and after ice sheet removal, as well as trace element transport for both equilibrium and disequilibrium transport end members. The predicted

  19. Evaluation of Melt Behavior with initial Melt Velocity under SFR Severe Accidents

    Energy Technology Data Exchange (ETDEWEB)

    Heo, Hyo; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of); Jerng, Dong Wook [Chung-Ang Univ, Seoul (Korea, Republic of)

    2015-10-15

    In the current Korean sodium-cooled fast reactor (SFR) program, early dispersion of the molten metallic fuel within a subchannel is suggested as one of the inherent safety strategies for the initiating phase of hypothetical core disruptive accident (HCDA). The safety strategy provides negative reactivity driven by the melt dispersal, so it could reduce the possibility of the recriticality event under a severe triple or more fault scenario for SFR. Since the behavior of the melt dispersion is unpredictable, it depends on the accident condition, particularly core region. While the voided coolant channel region is usually developed in the inner core, the unvoided coolant channel region is formed in the outer core. It is important to confirm the fuel dispersion with the core region, but there are not sufficient existing studies for them. From the existing studies, the coolant vapor pressure is considered as one of driving force to move the melt towards outside of the core. There is a complexity of the phenomena during intermixing of the melt with the coolant after the horizontal melt injections. It is too difficult to understand the several combined mechanisms related to the melt dispersion and the fragmentation. Thus, it could be worthwhile to study the horizontal melt injections at lower temperature as a preliminary study in order to identify the melt dispersion phenomena. For this reason, it is required to clarify whether the coolant vapor pressure is the driving force of the melt dispersion with the core region. The specific conditions to be well dispersed for the molten metallic fuel were discussed in the experiments with the simulant materials. The each melt behavior was compared to evaluate the melt dispersion under the coolant void condition and the boiling condition. As the results, the following results are remarked: 1. The upward melt dispersion did not occur for a given melt and coolant temperature in the nonboiling range. Over current range of conditions

  20. Tunneling spectroscopy of a p-i-n diode interface

    Energy Technology Data Exchange (ETDEWEB)

    Loth, Sebastian; Wenderoth, Martin; Teichmann, Karen; Homoth, Jan; Loeser, Karolin; Ulbrich, Rainer G. [IV. Physikalisches Institut, Georg-August-Universitaet Goettingen (Germany); Malzer, Stefan; Doehler, Gottfried H. [Universitaet Erlangen-Nuernberg (Germany). Max-Planck-Research Group, Institute of Optics, Information, and Photonics

    2008-07-01

    The performance of modern semiconductor devices is largely influenced by the spatial distribution of dopants in the device's active region on the nanoscale. Since the late 80's Scanning Tunneling Microscopy (STM) was employed to study the local properties of p-n interfaces. Most studies were carried out on p-n superlattices allowing the investigation of intrinsic features accessible without applied bias across the diode. Here, a single GaAs p-i-n diode heterostructure is investigated with cross-sectional STM (X-STM) in a three-terminal configuration. External source and drain contacts control the electric field across the junction. Then, the diode's active region is mapped with atomic resolution. Local I(V)-spectroscopy (STS) directly resolves the band edge alignment from p to n for different diode bias conditions. The effect of the external electric field on the spatial and spectral images of individual dopant atoms in the active layer is discussed.

  1. [Biological basis of problematic internet use (PIN) and therapeutic implications].

    Science.gov (United States)

    Bauernhofer, Kathrin; Papousek, Ilona; Fink, Andreas; Unterrainer, Human Friedrich; Weiss, Elisabeth M

    2015-01-01

    The repetitive excessive use of internet has led to an increasing number of reports about the negative consequences of overuse and is now viewed as an important public health issue, although the diagnosis of internet addiction remains problematic. Increasing knowledge about the neurobiological mechanism of behavioral addictions will promote future research and is essential for the development of specific and effective treatment. Growing evidence suggests that the neurobiological substrates and pathways of internet addiction resemble those of substance dependency and other forms of behavioral addictions. This paper reviews the current neuroimaging findings and genetic influencing factors for problematic internet use (PIN)/internet addiction. Recent evidence from neuro-scientific studies has pointed out that certain dysfunctions in the prefrontal cortex possibly driven by impaired dopamine neurotransmission are related to symptoms of internet addiction. Finally the literature on psychological and pharmacological interventions for internet addiction will be discussed. However, due to a lack of methodological sound treatment studies in this field it is currently impossible to recommend any evidence-based treatment of internet addiction.

  2. Evidence of domain wall pinning in aluminum substituted cobalt ferrites

    Science.gov (United States)

    Maurya, J. C.; Janrao, P. S.; Datar, A. A.; Kanhe, N. S.; Bhoraskar, S. V.; Mathe, V. L.

    2016-08-01

    In the present work spinel structured cobalt ferrites with aluminum substitution having composition CoAlxFe2-xO4 (x=0.0, 0.1, 0.2 and 0.3) have been synthesized using chemical co-precipitation method. Their microstructural, magnetic, magnetostriction and magnetoimpedance properties have been investigated. The piezomagnetic coefficient (dλ/dH) obtained from magnetostriction data is found to enhance with 0.1 Al substitutions in place of iron which decreases with further increase of Al content. It is noticed that 0.3 Al substitutions in place of Fe introduces domain wall pinning as evidenced from magnetostriction, magnetoimpedance and dc magnetization data. It is noted that ferrites so prepared using a simple procedure are magnetostrictive in good measure and with the addition of very small amount of non-magnetic aluminum their magnetostriction has shown saturation at relatively low magnetic fields. Such magnetostrictive ferrites find their applications in magnetic sensors and actuators.

  3. Multi-stable dissipative structures pinned to dual hot spots

    CERN Document Server

    Tsang, Cheng Hou; Chow, Kwok Wing

    2011-01-01

    We analyze the formation of one-dimensional localized patterns in a nonlinear dissipative medium including a set of two narrow "hot spots" (HSs), which carry the linear gain, local potential, cubic self-interaction, and cubic loss, while the linear loss acts in the host medium. This system can be realized, as a spatial-domain one, in optics, and also in Bose-Einstein condensates of quasi-particles in solid-state settings. Recently, exact solutions were found for localized modes pinned to the single HS represented by the delta-function. The present paper reports analytical and numerical solutions for coexisting two- and multi-peak modes, which may be symmetric or antisymmetric with respect to the underlying HS pair. Stability of the modes is explored through simulations of their perturbed evolution. The sign of the cubic nonlinearity plays a crucial role: in the case of the self-focusing, only the fundamental symmetric and antisymmetric modes, with two local peaks tacked to the HSs, and no additional peaks bet...

  4. Measurement of nuclear fuel pin hydriding utilizing epithermal neutron scattering

    Energy Technology Data Exchange (ETDEWEB)

    Miller, W.H. [Univ. of Missouri, Columbia, MO (United States); Farkas, D.M.; Lutz, D.R. [General Electric Co., Pleasanton, CA (United States)

    1996-12-31

    The measurement of hydrogen or zirconium hydriding in fuel cladding has long been of interest to the nuclear power industry. The detection of this hydrogen currently requires either destructive analysis (with sensitivities down to 1 {mu}g/g) or nondestructive thermal neutron radiography (with sensitivities on the order of a few weight percent). The detection of hydrogen in metals can also be determined by measuring the slowing down of neutrons as they collide and rapidly lose energy via scattering with hydrogen. This phenomenon is the basis for the {open_quotes}notched neutron spectrum{close_quotes} technique, also referred to as the Hysen method. This technique has been improved with the {open_quotes}modified{close_quotes} notched neutron spectrum technique that has demonstrated detection of hydrogen below 1 {mu}g/g in steel. The technique is nondestructive and can be used on radioactive materials. It is proposed that this technique be applied to the measurement of hydriding in zirconium fuel pins. This paper summarizes a method for such measurements.

  5. Validation of WIMS-CANDU using Pin-Cell Lattices

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Won Young; Min, Byung Joo; Park, Joo Hwan [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    2006-07-01

    The WIMS-CANDU is a lattice code which has a depletion capability for the analysis of reactor physics problems related to a design and safety. The WIMS-CANDU code has been developed from the WIMSD5B, a version of the WIMS code released from the OECD/NEA data bank in 1998. The lattice code POWDERPUFS-V (PPV) has been used for the physics design and analysis of a natural uranium fuel for the CANDU reactor. However since the application of PPV is limited to a fresh fuel due to its empirical correlations, the WIMS-AECL code has been developed by AECL to substitute the PPV. Also, the WIMS-CANDU code is being developed to perform the physics analysis of the present operating CANDU reactors as a replacement of PPV. As one of the developing work of WIMS-CANDU, the U{sup 238} absorption cross-section in the nuclear data library of WIMS-CANDU was updated and WIMS-CANDU was validated using the benchmark problems for pin-cell lattices such as TRX-1, TRX-2, Bapl-1, Bapl-2 and Bapl-3. The results by the WIMS-CANDU and the WIMS-AECL were compared with the experimental data.

  6. Cooling Performance of an Impingement Cooling Device Combined with Pins

    Institute of Scientific and Technical Information of China (English)

    Dongliang QUAN; Songling LIU; Jianghai LI; Gaowen LIU

    2005-01-01

    Experimental study and one dimensional model analysis were conducted to investigate cooling performance of an integrated impingement and pin fin cooling device. A typical configuration specimen was made and tested in a large scale low speed closed-looped wind tunnel. Detailed two-dimensional contour maps of the temperature and cooling effectiveness were obtained for different pressure ratios and therefore different coolant flow-rates through the tested specimen. The experimental results showed that very high cooling effectiveness can be achieved by this cooling device with relatively small amount of coolant flow. Based on the theory of transpiration cooling in porous material, a one dimensional heat transfer model was established to analyze the effect of various parameters on cooling effectiveness. It was found from this model that the variation of heat transfer on the gas side, including heat transfer coefficient and film cooling effectiveness, of the specimen created much more effect on its cooling effectiveness than that of the coolant side. The predictions of the one-dimensional mode were compared and agreed well with the experimental data.

  7. Glucose inhibits root meristem growth via ABA INSENSITIVE 5, which represses PIN1 accumulation and auxin activity in Arabidopsis.

    Science.gov (United States)

    Yuan, Ting-Ting; Xu, Heng-Hao; Zhang, Kun-Xiao; Guo, Ting-Ting; Lu, Ying-Tang

    2014-06-01

    Glucose functions as a hormone-like signalling molecule that modulates plant growth and development in Arabidopsis thaliana. However, the role of glucose in root elongation remains elusive. Our study demonstrates that high concentrations of glucose reduce the size of the root meristem zone by repressing PIN1 accumulation and thereby reducing auxin levels. In addition, we verified the involvement of ABA INSENSITIVE 5 (ABI5) in this process by showing that abi5-1 is less sensitive to glucose than the wild type, whereas glucose induces ABI5 expression and the inducible overexpression of ABI5 reduces the size of the root meristem zone. Furthermore, the inducible overexpression of ABI5 in PIN1::PIN1-GFP plants reduces the level of PIN1-GFP, but glucose reduces the level of PIN1-GFP to a lesser extent in abi5-1 PIN1::PIN1-GFP plants than in the PIN1::PIN1-GFP control, suggesting that ABI5 is involved in glucose-regulated PIN1 accumulation. Taken together, our data suggest that ABI5 functions in the glucose-mediated inhibition of the root meristem zone by repressing PIN1 accumulation, thus leading to reduced auxin levels in roots. © 2013 John Wiley & Sons Ltd.

  8. Viscosity of ring polymer melts

    KAUST Repository

    Pasquino, Rossana

    2013-10-15

    We have measured the linear rheology of critically purified ring polyisoprenes, polystyrenes, and polyethyleneoxides of different molar masses. The ratio of the zero-shear viscosities of linear polymer melts η0,linear to their ring counterparts η0,ring at isofrictional conditions is discussed as a function of the number of entanglements Z. In the unentangled regime η0,linear/η 0,ring is virtually constant, consistent with the earlier data, atomistic simulations, and the theoretical expectation η0,linear/ η0,ring = 2. In the entanglement regime, the Z-dependence of ring viscosity is much weaker than that of linear polymers, in qualitative agreement with predictions from scaling theory and simulations. The power-law extracted from the available experimental data in the rather limited range 1 < Z < 20, η0,linear/η0,ring ∼ Z 1.2±0.3, is weaker than the scaling prediction (η0,linear/η0,ring ∼ Z 1.6±0.3) and the simulations (η0,linear/ η0,ring ∼ Z2.0±0.3). Nevertheless, the present collection of state-of-the-art experimental data unambiguously demonstrates that rings exhibit a universal trend clearly departing from that of their linear counterparts, and hence it represents a major step toward resolving a 30-year-old problem. © 2013 American Chemical Society.

  9. BARREN INFLORESCENCE2 interaction with ZmPIN1a suggests a role in auxin transport during maize inflorescence development.

    Science.gov (United States)

    Skirpan, Andrea; Culler, Angela Hendrickson; Gallavotti, Andrea; Jackson, David; Cohen, Jerry D; McSteen, Paula

    2009-03-01

    Polar auxin transport, mediated by the PIN-FORMED (PIN) class of auxin efflux carriers, controls organ initiation in plants. In maize, BARREN INFLORESCENCE2 (BIF2) encodes a serine/threonine protein kinase co-orthologous to PINOID (PID), which regulates the subcellular localization of AtPIN1 in Arabidopsis. We show that BIF2 phosphorylates ZmPIN1a, a maize homolog of AtPIN1, in vitro and regulates ZmPIN1a subcellular localization in vivo, similar to the role of PID in Arabidopsis. In addition, bif2 mutant inflorescences have lower auxin levels later in development. We propose that BIF2 regulates auxin transport through direct regulation of ZmPIN1a during maize inflorescence development.

  10. Study on melting conditions of radioactive miscellaneous solid waste. Contract research

    Energy Technology Data Exchange (ETDEWEB)

    Fukui, Toshiki; Nakashio, Nobuyuki; Isobe, Motoyasu; Otake, Atsushi; Wakui, Takuji; Nakashima, Mikio [Department of Decommissioning and Waste Management, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Hirabayashi, Takakuni [Radiation Application Develpment Association, Tokai, Ibaraki (Japan)

    2001-02-01

    Improvement of fluidity of molten slag is one of the most important factors for plasma melting treatment of low level radioactive miscellaneous wastes generated from nuclear facilities. In general, it is considered that elevating molten slag temperature of addition of flux is of certain use in improvement of fluidity of molten slag. However, these ways are not necessarily suitable from the viewpoints of refractory erosion or reduction of waste volume. In this report, we suggested that fluidity of molten slag could be improved by controlling chemical compositions of molten slag. On the Basic of the investigation using phase diagram and viscosity data, FeO was selected as a key component for improving fluidity: Viscosity and melting point of molten slag decreased with increasing relative concentration of FeO in molten slag. Accordingly, we concluded that it is important to adjust basicity of molten slag for melting treatment of low-level radioactive miscellaneous solid wastes. (author)

  11. Analysis of melting and solidification behaviour of glass-forming alloys by synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Baser, T.A.; Baricco, M. [Dipartimento di Chimica, Universita di Torino (Italy); NIS, Torino (Italy); Bostrom, M. [The European Synchrotron Radiation Facility, (ESRF), Grenoble (France); Stoica, M. [Leibniz-Institut fuer Festkorper- und Werkstoffforschung Dresden (Germany); Yavari, A.R. [Laboratorie de Thermodynamique et Physico-chimie Metallurgique (LTPCM-UMR 5614), Institut National Polytechnique de Grenoble, CNRS (France)

    2007-06-15

    This paper aims to study the melting and solidification behaviour of Fe48Cr15Mo14Y2C15B6 and Cu50Zr50 glass-forming alloys by in-situ synchrotron X-ray diffraction from data obtained at the European Synchrotron Radiation Facility (ESRF). Melting and solidification behaviour for both alloys were measured by high temperature differential scanning calorimetry (HTDSC). The phase identification was performed by Rietveld refinement of diffraction patterns collected as a function of temperature. The phase mixture on melting and solidification has been clarified, confirming that in-situ X-ray diffraction by synchrotron radiation is a powerful technique for the study of phase transformations in alloys. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  12. Jupiter Laser Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Jupiter Laser Facility is an institutional user facility in the Physical and Life Sciences Directorate at LLNL. The facility is designed to provide a high degree...

  13. Basic Research Firing Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Basic Research Firing Facility is an indoor ballistic test facility that has recently transitioned from a customer-based facility to a dedicated basic research...

  14. A Fast Guide Tube Position Estimation Algorithm for a Control Rod Support Pin Inspection Robot

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jae C.; Jeon, Hyeong S.; Choi, Yu R.; Kim, Jae H. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    2005-07-01

    The risk that PWR guide tube support pins will crack has increased the necessity for the development of inspection methods and equipment. A special remote-controlled manipulator has been widely used to inspect the guide tube support pins. We presented a matched filter algorithm for detecting the existence and estimating the position of the guide tube support pins. But, the matched filter algorithm requires numbers of complex floating point calculations for the 2-D FFT and therefore it can not be fitted in to the small-sized embedded processors. We proposed a new simplified method for estimating the position of the guide tube support pins. It uses most of the operations with integers. We ported the proposed method in intel's xscale processor running at 400 mhz. We used gnu C language in embedded linux operating system. We can calculate the algorithm at a rate of 20 frames/sec. in a 160x120 image size.

  15. Magnetic nanoparticles in MgB2: Vortex pinning, pair breaking and connectivity

    Science.gov (United States)

    Babić, Emil; Novosel, Nikolina; Pajić, Damir; Galić, Stipe; Zadro, Krešo; Drobac, Đuro

    2016-02-01

    The results indicating magnetic flux pinning in MgB2 wires doped with three types of magnetic nanoparticles (MNP) are reported. The magnetic state of MNPs, both as-prepared and inside the MgB2 core, was determined with magnetization and ac susceptibility measurements. The competition between detrimental influence of doping (reduced connectivity, pair breaking) and enhanced flux pinning leads to deterioration of electromagnetic properties of doped wires at high MNP content, whereas light doping causes an enhancement of critical current density, Jc, and/or irreversibility field, Birr, for all our MNPs. For Ni and dextrin coated NiFe2O4 MNPs the enhancement of Jc was comparable to that achieved with the best nonmagnetic dopands. Detailed analysis indicates the contribution of magnetic flux pinning including the matching effects in flux pinning on MNPs.

  16. Canoe binds RanGTP to promote Pins(TPR)/Mud-mediated spindle orientation.

    Science.gov (United States)

    Wee, Brett; Johnston, Christopher A; Prehoda, Kenneth E; Doe, Chris Q

    2011-10-31

    Regulated spindle orientation maintains epithelial tissue integrity and stem cell asymmetric cell division. In Drosophila melanogaster neural stem cells (neuroblasts), the scaffolding protein Canoe (Afadin/Af-6 in mammals) regulates spindle orientation, but its protein interaction partners and mechanism of action are unknown. In this paper, we use our recently developed induced cell polarity system to dissect the molecular mechanism of Canoe-mediated spindle orientation. We show that a previously uncharacterized portion of Canoe directly binds the Partner of Inscuteable (Pins) tetratricopeptide repeat (TPR) domain. The Canoe-Pins(TPR) interaction recruits Canoe to the cell cortex and is required for activation of the Pins(TPR)-Mud (nuclear mitotic apparatus in mammals) spindle orientation pathway. We show that the Canoe Ras-association (RA) domains directly bind RanGTP and that both the Canoe(RA) domains and RanGTP are required to recruit Mud to the cortex and activate the Pins/Mud/dynein spindle orientation pathway.

  17. Selective pinning control of the average disease transmissibility in an HIV contact network

    Science.gov (United States)

    du Toit, E. F.; Craig, I. K.

    2015-07-01

    Medication is applied to the HIV-infected nodes of high-risk contact networks with the aim of controlling the spread of disease to a predetermined maximum level. This intervention, known as pinning control, is performed both selectively and randomly in the network. These strategies are applied to 300 independent realizations per reference level of incidence on connected undirectional networks without isolated components and varying in size from 100 to 10 000 nodes per network. It is shown that a selective on-off pinning control strategy can control the networks studied with limited steady-state error and, comparing the medians of the doses from both strategies, uses 51.3% less medication than random pinning of all infected nodes. Selective pinning could possibly be used by public health specialists to identify the maximum level of HIV incidence in a population that can be achieved in a constrained funding environment.

  18. Late-onset chest wall abscess due to a biodegradable rib pin infection after lung transplantation.

    Science.gov (United States)

    Goda, Yasufumi; Chen-Yoshikawa, Toyofumi F; Kusunose, Masaaki; Hamaji, Masatsugu; Motoyama, Hideki; Hijiya, Kyoko; Aoyama, Akihiro; Date, Hiroshi

    2017-03-17

    A 55-year-old man with end-stage emphysema underwent a right single-lung transplantation through a posterolateral thoracotomy. The fifth rib was divided and fused back using a biodegradable pin made of polylactide acid and hydroxyapatite. Two weeks postoperatively, he suffered from central vein catheter-related sepsis due to methicillin-sensitive Staphylococcus aureus. After being successfully treated for sepsis, he was discharged. However, 3 months later, computed tomography revealed multiple loculated abscesses in the chest wall and the right pleural space. Reoperative thoracotomy revealed abscesses mainly located around the fifth rib, where the pin was inserted. Both cultures of the abscess and the fifth rib were positive for methicillin-sensitive S. aureus, which suggested that the rib pin was the cause of the secondary infection. This case suggests the rib pins, even if they are biodegradable, could have a risk of infections side effect especially for the immunosuppressed patients.

  19. Cellular peptidyl-prolyl cis/trans isomerase Pin1 facilitates replication of feline coronavirus.

    Science.gov (United States)

    Tanaka, Yoshikazu; Amano, Arisa; Morisaki, Masateru; Sato, Yuka; Sasaki, Takashi

    2016-02-01

    Although feline coronavirus (FCoV) causes feline infectious peritonitis (FIP), which is a fatal infectious disease, there are no effective therapeutic medicines or vaccines. Previously, in vitro studies have shown that cyclosporin (CsA) and FK506 inhibit virus replication in diverse coronaviruses. CsA and FK506 are targets of clinically relevant immunosuppressive drugs and bind to cellular cyclophilins (Cyps) or FK506 binding proteins (FKBPs), respectively. Both Cyp and FKBP have peptidyl-prolyl cis-trans isomerase (PPIase) activity. However, protein interacting with NIMA (Pin1), a member of the parvulin subfamily of PPIases that differs from Cyps and FKBPs, is essential for various signaling pathways. Here we demonstrated that genetic silencing or knockout of Pin1 resulted in decreased FCoV replication in vitro. Dipentamethylene thiuram monosulfide, a specific inhibitor of Pin1, inhibited FCoV replication. These data indicate that Pin1 modulates FCoV propagation.

  20. Evaporation of droplets on strong and low-pinning surfaces and dynamics of the triple line

    CERN Document Server

    Bormashenko, Edward; Zinigrad, Michael

    2011-01-01

    Evaporation of water droplets deposited on metal and polymer substrates was studied. The evaporated droplet demonstrates different behaviors on low-pinning (polymer) and strong-pinning (metallic) surfaces. When deposited on polymer surfaces, the evaporated droplet is featured by stick-slip sliding, whereas on strong-pinning metallic surfaces it does not show such kind of motion and demonstrates the giant contact-angle hysteresis. Stick-slip motion of droplets is described satisfactorily by the Shanahan-Sefiane model relating this kind of motion to surmounting potential barriers caused by the pinning of the triple (three-phase) line. The experimentally established "stick" times coincide with the values predicted by the Shanahan-Sefiane theory. The values of potential barriers are reported. The notion of the equilibrium contact angle is refined.