WorldWideScience

Sample records for pige analysis

  1. Potential of the PIGE method in the analysis of biological and mineral materials

    International Nuclear Information System (INIS)

    Havranek, V.

    2006-01-01

    A possible application of the PIGE method for the analysis of the biological and mineral samples has been tested using a 3.5 MeV Van de Graaff accelerator. The limits of detection of 4 mg/kg for fluorine, 10 mg/kg for aluminium and 200 mg/kg for phosphorus were achieved with a 3.15 MeV proton beam (8 mm in diameter, 20 nA current and 1000 s irradiation time). The PIGE method was found to be a suitable method for the determination of fluorine in the samples analyzed. With this technique, total fluorine in the sample can be quantitated without any chemical treatment. In the analysis of the phosphorus in thick biological samples, PIGE can compete with PIXE and is probably less sensitive to matrix effects and spectra fitting, which may bring about a higher accuracy of the results

  2. Quantitative analysis of light elements in aerosol samples by PIGE

    International Nuclear Information System (INIS)

    Mateus, R.; Reis, M.A.; Jesus, A.P.; Ribeiro, J.P.

    2006-01-01

    Quantitative PIGE analysis of aerosol samples collected on nuclepore polycarbonate filters was performed by a method that avoids the use of comparative standards. Nuclear cross sections and calibration parameters established before in an extensive work on thick and intermediate samples were employed. For these samples, the excitation functions of nuclear reactions, induced by the incident protons on target's light elements, were used as input for a code that evaluates the gamma-ray yield integrating along the depth of the sample. In the present work we apply the same code to validate the use of an effective energy for thin sample analysis. Results pertaining to boron, fluorine and sodium concentrations are presented. In order to establish a correlation with sodium values, PIXE results related to chlorine are also presented, giving support to the reliability of this PIGE method for thin film analysis

  3. PIXE–PIGE analysis of size-segregated aerosol samples from remote areas

    Energy Technology Data Exchange (ETDEWEB)

    Calzolai, G., E-mail: calzolai@fi.infn.it [Department of Physics and Astronomy, University of Florence and National Institute of Nuclear Physics (INFN), Via G. Sansone 1, 50019 Sesto Fiorentino (Italy); Chiari, M.; Lucarelli, F.; Nava, S.; Taccetti, F. [Department of Physics and Astronomy, University of Florence and National Institute of Nuclear Physics (INFN), Via G. Sansone 1, 50019 Sesto Fiorentino (Italy); Becagli, S.; Frosini, D.; Traversi, R.; Udisti, R. [Department of Chemistry, University of Florence, Via della Lastruccia 3, 50019 Sesto Fiorentino (Italy)

    2014-01-01

    The chemical characterization of size-segregated samples is helpful to study the aerosol effects on both human health and environment. The sampling with multi-stage cascade impactors (e.g., Small Deposit area Impactor, SDI) produces inhomogeneous samples, with a multi-spot geometry and a non-negligible particle stratification. At LABEC (Laboratory of nuclear techniques for the Environment and the Cultural Heritage), an external beam line is fully dedicated to PIXE–PIGE analysis of aerosol samples. PIGE is routinely used as a sidekick of PIXE to correct the underestimation of PIXE in quantifying the concentration of the lightest detectable elements, like Na or Al, due to X-ray absorption inside the individual aerosol particles. In this work PIGE has been used to study proper attenuation correction factors for SDI samples: relevant attenuation effects have been observed also for stages collecting smaller particles, and consequent implications on the retrieved aerosol modal structure have been evidenced.

  4. Analysis of light elements by PIGE

    International Nuclear Information System (INIS)

    Kim, Y. S.; Choi, H. W.; Kim, D. K.; Woo, H. J.; Kim, N. B.; Park, K. S.

    2000-01-01

    The PIGE (Proton Induced Gamma ray Emission) method was applied for the measurement of light elements Li - K. A test measurement has been performed for geological, biological, environmental and material samples by using a standard sample for each element. The measurement was performed for the two proton energies of 2.4 and 3.4 MeV, and 3.4MeV was found to yield better result for multielemental analysis. The result shows a fair agreement within 15% for all elements with standard values. The detection limits of Li, B, F and Na are less than 100 ppm, while those of the other elements are from a few hundred ppm to a few percents. (author)

  5. Relationship between microhardness and fluorine contents on tooth enamel determined by PIGE analysis

    International Nuclear Information System (INIS)

    Ma, D.S.; Paik, D.I.; Park, D.Y.; Moon, H.S.; Chang, Y.I.; Kim, J.B.

    1997-01-01

    The remineralization effect of fluoride has been measured by surface microhardness on tooth enamel. The purpose of this study was to investigate the relationship between microhardness and fluorine concentration on tooth enamel. Twelve sound bovine enamel specimens were prepared and immersed in 0.05% NaF solution for 1, 3, 6, 24 and 36 hours, respectively. The concentration of fluorine in specimens were measured by PIGE analysis and surface microhardness of each specimen was measured by surface microhardness tester. Fluorine concentration was increased by immersing time. There was no change in microhardness of each specimen by fluorine content. The results of this study suggest that there was no relationship between the fluorine concentration and surface microhardness in sound tooth enamel. PIGE analysis can be used effectively to assess the remineralization effect of fluorine content in tooth enamel. (author)

  6. Fluorine determination in diet samples using cyclic NAA and PIGE analysis

    International Nuclear Information System (INIS)

    Farooqi, A.S.; Arshed, W.; Akanle, O.A.; Spyrou, N.M.

    1991-01-01

    Fluorine is an important trace element for life and human well-being. Food, in general, provides about 40% of the fluorine intake in the human body. In order to measure fluorine levels in human diet samples, Instrumental Neutron Activation Analysis (INAA) and Proton Induced Gamma-Ray Emission (PIGE) analysis were used. Thermal and epithermal cyclic NAA methods were applied, employing the 19 F(n,γ) 20 F and 19 F(n,p) 19 O nuclear reactions for the determination of fluorine, respectively. Corrections were made for the sodium matrix interference caused by the 23 Na(n,α) 20 F threshold reaction in the case of thermal cyclic NAA and for the oxygen interference via 18 O(n,γ) 19 O reaction when using the epithermal cyclic NAA method. The fluorine contents of diet samples were also determined by PIGE analysis making use of the resonance reaction 19 F(p,αγ) 16 O at 872 KeV. Thermal cyclic NAA was found to be most suitable for the determination of low concentrations of fluorine in the diet samples, with a detection limit of less than 10 μg/g

  7. PIGE-PIXE analysis of chewing sticks of pharmacological importance

    Energy Technology Data Exchange (ETDEWEB)

    Olabanji, S.O. [Istituto Nazionale di Fisica Nucleare (INFN), Padua (Italy). Lab. Nazionali di Legnaro; Makanju, O.V. [Drug Research and Production Unit, Faculty of Pharmacy, Obafemi Awolowo University (O.A.U.), Ile-Ife (Nigeria); Haque, A.M.I. [Istituto Nazionale di Fisica Nucleare (INFN), Padua (Italy). Lab. Nazionali di Legnaro; Buoso, M.C. [Istituto Nazionale di Fisica Nucleare (INFN), Padua (Italy). Lab. Nazionali di Legnaro; Ceccato, D. [Istituto Nazionale di Fisica Nucleare (INFN), Padua (Italy). Lab. Nazionali di Legnaro]|[Dipartimento di Fisica, Universita di Padova, I-35131 Padova (Italy); Cherubini, R. [Istituto Nazionale di Fisica Nucleare (INFN), Padua (Italy). Lab. Nazionali di Legnaro; Moschini, G. [Istituto Nazionale di Fisica Nucleare (INFN), Padua (Italy). Lab. Nazionali di Legnaro]|[Dipartimento di Fisica, Universita di Padova, I-35131 Padova (Italy)

    1996-06-01

    PIGE and PIXE techniques were employed for the determination of the major, minor and trace elemental concentrations in chewing sticks of pharmacological importance namely: Butyrospermum paradoxum, Garcinia kola, Distemonanthus benthamianus, Bridelia ferruginea, Anogeissus leiocarpus, Terminalia glaucescens and Fagara rubescens, respectively. The concentration of fluorine which is very important for human dental enamel was specially determined using the {sup 19}F(p,p`{gamma}){sup 19}F reaction. For decades these chewing sticks when used alone without toothpastes have proven to be very efficient, effective and reliable in cleaning the teeth of many people particularly in Nigeria and some other countries in Africa. The teeth of users are usually very strong, clean, fresh and devoid of germs and caries. Even with the advent of modern toothpastes with special additions of fluorine, the use of these popular and efficient chewing sticks is still unabated. Many people including the elite use them solely, a few others combine their use with modern toothpastes and brush. Proton beams produced by the 7 MV CN and 2.5 MV AN 2000 Van de Graaff accelerators at INFN, Laboratori Nazionali di Legnaro (LNL), Padova, Italy were used for the PIGE and PIXE analysis, respectively. Results of this novel study are presented and discussed. (orig.).

  8. PIGE-PIXE analysis of chewing sticks of pharmacological importance

    International Nuclear Information System (INIS)

    Olabanji, S.O.; Haque, A.M.I.; Cherubini, R.

    1996-01-01

    PIGE and PIXE techniques were employed for the determination of the major, minor and trace elemental concentrations in chewing sticks of pharmacological importance namely: Butyrospermum paradoxum, Garcinia kola, Distemonanthus benthamianus, Bridelia ferruginea, Anogeissus leiocarpus, Terminalia glaucescens and Fagara rubescens, respectively. The concentration of fluorine which is very important for human dental enamel was specially determined using the 19 F(p,p'γ) 19 F reaction. For decades these chewing sticks when used alone without toothpastes have proven to be very efficient, effective and reliable in cleaning the teeth of many people particularly in Nigeria and some other countries in Africa. The teeth of users are usually very strong, clean, fresh and devoid of germs and caries. Even with the advent of modern toothpastes with special additions of fluorine, the use of these popular and efficient chewing sticks is still unabated. Many people including the elite use them solely, a few others combine their use with modern toothpastes and brush. Proton beams produced by the 7 MV CN and 2.5 MV AN 2000 Van de Graaff accelerators at INFN, Laboratori Nazionali di Legnaro (LNL), Padova, Italy were used for the PIGE and PIXE analysis, respectively. Results of this novel study are presented and discussed. (orig.)

  9. PIGE-PIXE analysis of chewing sticks of pharmacological importance

    Science.gov (United States)

    Olabanji, S. O.; Makanju, O. V.; Haque, A. M. I.; Buoso, M. C.; Ceccato, D.; Cherubini, R.; Moschini, G.

    1996-06-01

    PIGE and PIXE techniques were employed for the determination of the major, minor and trace elemental concentrations in chewing sticks of pharmacological importance namely: Butyrospermum paradoxum, Garcinia kola, Distemonanthus benthamianus, Bridelia ferruginea, Anogeissus leiocarpus, Terminalia glaucescens and Fagara rubescens, respectively. The concentration of fluorine which is very important for human dental enamel was specially determined using the 19F(p, p'γ) 19F reaction. For decades these chewing sticks when used alone without toothpastes have proven to be very efficient, effective and reliable in cleaning the teeth of many people particularly in Nigeria and some other countries in Africa. The teeth of users are usually very strong, clean, fresh and devoid of germs and caries. Even with the advent of modern toothpastes with special additions of fluorine, the use of these popular and efficient chewing sticks is still unabated. Many people including the elite use them solely, a few others combine their use with modern toothpastes and brush. Proton beams produced by the 7 MV CN and 2.5 MV AN 2000 Van de Graaff accelerators at INFN, Laboratori Nazionali di Legnaro (LNL), Padova, Italy were used for the PIGE and PIXE analysis, respectively. Results of this novel study are presented and discussed.

  10. PIXE-PIGE analysis of some Indian medicinal plants

    Science.gov (United States)

    Nomita Devi, K.; Nandakumar Sarma, H.

    2010-06-01

    The quantitative estimation of various trace element concentrations in medicinal plants is necessary for determining their effectiveness in treating various diseases and for understanding their pharmacological action. Elemental concentrations of some selected medicinal plants of north east India was measured by proton induced X-ray emission (PIXE) and proton induced γ-ray emission (PIGE) techniques. PIXE measurements were carried out using 2.4 MeV collimated protons from the 3 MV tandetron accelerator of NCCCM, Hyderabad (India) while the PIGE measurements were carried out using 3 MeV protons from the same accelerator in the same laboratory. Accuracy and precision of the techniques were assured by analyzing certified reference materials in the same experimental conditions. Various elements of biological importance in man's metabolism were found to be present in varying concentrations in the studied medicinal plants and no toxic heavy metals were detected. The concentration of the various elements in the medicinal plants and their role in treating various diseases are discussed.

  11. PIXE-PIGE analysis of some Indian medicinal plants

    Energy Technology Data Exchange (ETDEWEB)

    Nomita Devi, K., E-mail: nomita_k@rediffmail.co [Department of Physics, Manipur University, Canchipur, Imphal 795003 (India); Nandakumar Sarma, H. [Department of Physics, Manipur University, Canchipur, Imphal 795003 (India)

    2010-06-15

    The quantitative estimation of various trace element concentrations in medicinal plants is necessary for determining their effectiveness in treating various diseases and for understanding their pharmacological action. Elemental concentrations of some selected medicinal plants of north east India was measured by proton induced X-ray emission (PIXE) and proton induced {gamma}-ray emission (PIGE) techniques. PIXE measurements were carried out using 2.4 MeV collimated protons from the 3 MV tandetron accelerator of NCCCM, Hyderabad (India) while the PIGE measurements were carried out using 3 MeV protons from the same accelerator in the same laboratory. Accuracy and precision of the techniques were assured by analyzing certified reference materials in the same experimental conditions. Various elements of biological importance in man's metabolism were found to be present in varying concentrations in the studied medicinal plants and no toxic heavy metals were detected. The concentration of the various elements in the medicinal plants and their role in treating various diseases are discussed.

  12. Quantitative analysis of light elements in thick samples by PIGE

    International Nuclear Information System (INIS)

    Mateus, R.; Jesus, A.P.; Ribeiro, J.P.

    2004-01-01

    PIGE analysis of thick and intermediate samples is usually performed with the help of standards, but this method gives only good results when the standard is very similar to the sample to be analysed. In this work, we present an alternative method for PIGE analysis of light elements in thick samples. This method is based on a code that integrates the nuclear reaction excitation function along the depth of the sample. For the integration procedure the sample is divided in sublayers, defined by the energy steps that were used to measure accurately the excitation function. This function is used as input. Within each sublayer the stopping power cross-sections may be assumed as constant. With these two conditions the calculus of the contribution of each sublayer for the total yield becomes an easy task. This work presents results for the analysis of lithium, boron, fluorine and sodium in thick samples. For this purpose, excitation functions of the reactions 7 Li(p,p ' γ) 7 Li, 19 F(p,p ' γ) 19 F, 10 B(p,αγ) 7 Be and 23 Na(p,p ' γ) 23 Na were employed. Calculated γ-ray yields were compared, at several proton energy values, with experimental yields for thick samples made of inorganic compounds of the referred elements. The agreement is better than 7.5%. Taking into consideration the experimental uncertainty of the measured yields and the errors related to the stopping power values used, this agreement shows that effects as the beam energy straggling, ignored in the calculation, seem to play a minor role

  13. Modification of IBANDL to Accommodate PIGE Data. Study of the Feasibility of Producing Evaluations for PIGE

    International Nuclear Information System (INIS)

    Gurbich, A.

    2013-01-01

    According to the plan for special actions accepted at the 1st RCM the necessary changes were made in IBANDL and in the R33-format to accommodate PIGE data. The data to be included in IBANDL are differential cross sections and thick target yields. IBANDL was modified in order to enable it to deal with both kinds of data. The following change was made in the R33 format: for PIGE data an additional entry ''Egamma:'' which contains the gamma-ray energy in keV was inserted, the sign '+' being used between the energies for unresolved lines. This entry is used as a flag to identify PIGE data and to sort files in the table of the retrieved data according to the γ-ray energy. The γ-ray energy is also displayed in the table of retrieved data. A corresponding change was also made in the template used for the upload of the R33 files. The lines with PIGE data are placed at the bottom of the table after EBS and NRA data. A new unit 'yield' was introduced in the R33 format. The data presented in this unit should contain a thick target yield of gammas in Nγ / sr μC. The script producing IBANDL graphics was modified to plot the data in the 'yield' units. However, the possibility to compare the data presented in R33 files as cross-sections and yield in the same plot has not been implemented yet because of the lack of a light version of ERYA code which could be called by IBANDL to perform calculations of target yields using the differential cross section data. The work on transferring EXFOR files relevant to PIGE into IBANDL was hampered by the interruption of the remote access to the server due to computer security measures introduced in the IAEA. The feasibility of producing evaluations for PIGE was studied according to the plan of special actions. The gamma emission used in PIGE is of two kinds - primary γ-rays and cascade ones. For primary gammas the excitation function can be calculated using the R-matrix theory and a good agreement between theory and experiment can be

  14. PIGE-PIXE analysis of medicinal plants and vegetables of pharmacological importance

    International Nuclear Information System (INIS)

    Olabanji, S.O.; Makanju, O.V.

    1995-08-01

    PIGE and PIXE techniques were employed to the study of elemental constituents of some traditional medicinal plants generally used in curing many diseases and ailments in South-Western Nigeria. Analysis were also carried out on commonly edible vegetables of medicinal and pharmacological importance. PIGE measurements were carried out using 3.5 MeV collimated protons from the 7 MV CN Van-de-Graaff accelerator of INFN, LNL, Legnaro (Padova), Italy, while the PIXE measurements were carried out using 1.8 MeV from the 2.5 MV AN 2000 Van-de-Graaff accelerator of the same laboratory. The results show that many of the medicinal plants contain elements of cardinal importance in man's metabolism. The results from the vegetables also show that presence of vital elements that are needed for growth and developments. In addition, some of the toxic elements which include arsenic, cadmium, mercury, etc. were not detected. However, some of the recipes contain trace amounts of lead at very low concentrations. This calls for proper control of dose rates in some samples to prevent the attendant negative cumulative effects. (author). 17 refs, 1 fig., 5 tabs

  15. Proposal of an interlaboratory PIGE experiment

    International Nuclear Information System (INIS)

    Pedro de Jesus, A.

    2014-01-01

    Full text: Taking into consideration that: 1. There has been within this CRP a great effort to compile nuclear cross section data from the literature and also to measure additional data; 2. This effort has included a concerted experiment on Al(p,p’γ) reaction in order to assess and evaluate the experimental difficulties and uncertainties; 3. The goals of the CRP have also included the development of codes to calculate gamma ray yields from cross section data that has been done (ERYA code); a proposal is made to measure by PIGE in another concerted laboratory action an unknown sample with one (or more than one) relevant element (isotope) and calculate the concentrations from the yields using the ERYA code. The important outputs of this experiment would be: - the assessment and evaluation of the effect that uncertainties in the cross section data have on PIGE results; - a concerted evaluation of the ERYA code; - a demonstration for the PIGE community of standard-less PIGE and of its capabilities. In the discussion that followed it was decided that although very pertinent and important, there was no time during this CRP to engage in such an experiment. Furthermore, it was considered a bit out of the main scope of this CRP. (author)

  16. Analysis of Roman glass from Albania by PIXE–PIGE method

    International Nuclear Information System (INIS)

    Šmit, Ž.; Tartari, F.; Stamati, F.; Vevecka Priftaj, A.; Istenič, J.

    2013-01-01

    A series of 31 Roman glasses dated to the 1st–4th c. AD from the present Albania was analyzed by the combined PIXE–PIGE method. The analysis shows typical natron-based glass of the Roman period, though statistical treatment using principal component analysis and bivariate plots reveals four distinct groups, which are qualified by increased levels of potassium, magnesium and titanium–manganese–iron oxides, respectively. MgO content may exceed 2% and reach the level commonly accepted for halophytic plant-ash glass. The groups are formed on account of mineral impurities in the sand, which gives support to the thesis of multiple production centers of raw glass in the imperial age

  17. Development of a Reference Database for Particle Induced Gamma Ray Emission (PIGE) Spectroscopy

    International Nuclear Information System (INIS)

    2017-09-01

    Ion beam analysis techniques are non-destructive analytical techniques used to identify the composition and structure of surface layers of materials. The applications of these techniques span environmental control, cultural heritage and conservation, materials and fusion technologies. The particle-induced gamma-ray emission (PIGE) spectroscopy technique in particular, is a powerful tool for detecting light elements in certain depths of surface layers. This publication describes the coordinated effort to measure and compile cross section data relevant to PIGE analysis and make these data available to the community of practice through a comprehensive online database.

  18. Study of stained glass window using PIXE-PIGE

    International Nuclear Information System (INIS)

    Weber, G.; Bemden, Y. Vanden; Pirotte, M.; Gilbert, B.

    2005-01-01

    We had the opportunity to study a large panel (100x80cm) containing more than 40 stained glass pieces. Among them several come from restorations having taken place at different periods. The study of this rather complex arrangement has been processed by stages:- the elemental composition of 16 zones were determined: several differences were identified and among them the Na/K ratio which allowed to set three groups of glass type; - the measurement of the Na concentrations by the two techniques give information in bulk (PIGE) and at the near surface (PIXE); the values defined by the (C PIGE -C PIXE) )/C PIGE plotted in function of the historical estimation of the age of the stained glass pieces (original and restored) indicate a real correlation between the two variables; - the red-colored pieces were specially investigated in order to determine which coloration technique was employed (bulk coloration, superficial staining, multilayered flashing, etc.); - the corrosion was investigated by scanning two different worsened zones with a 0.5mm diameter beam spot. This study shows the possibilities of the PIGE-PIXE association, but also points out some weaknesses, which have to be solved by other techniques; unfortunately, in that case, the non-destructive aspect could be lost

  19. PIXE-PIGE analysis of late roman glass fragments

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Tubio, B. [Departamento de Fisica Aplicada III, Escuela de Ingenieros, Universidad de Sevilla, Camino de los Descubrimientos s/n, 41092 Sevilla (Spain)]. E-mail: tubio@us.es; Ontalba Salamanca, M.A. [Departamento de Fisica, Escuela Politecnica, Universidad de Extremadura, Avda. de la Universidad s/n, 10071 Caceres (Spain); Ortega-Feliu, I. [Centro Nacional de Aceleradores, Universidad de Sevilla, Avda. Thomas A. Edison s/n, 41092 Sevilla (Spain); Respaldiza, M.A. [Centro Nacional de Aceleradores, Universidad de Sevilla, Avda. Thomas A. Edison s/n, 41092 Sevilla (Spain); Amores Carredano, F. [Departamento de Prehistoria y Arqueologia, Universidad de Sevilla, C/Dona Maria de Padilla s/n, 41010 Sevilla (Spain); Gonzalez-Acuna, D. [Departamento de Geografia, Historia y Filosofia, Universidad Pablo de Olavide, Ctra. de Utrera Km 1, 41013 Sevilla (Spain)

    2006-08-15

    A set of Roman glass fragments, excavated at Sevilla and dated in the 5th century A.D., has been analysed by PIXE and PIGE techniques using the external beam set-up of the 3 MV tandem Pelletron accelerator of the CNA at the University of Sevilla. Using a simple quantification method, based on the indirect charge calculation on the sample by monitoring the X-ray induced by the proton beam on the exit window, the composition of the glasses has been determined. From the obtained results, the use of soda as flux has been inferred and colouring manufacture procedures have been identified.

  20. Assessment of nuclear data needs for particle induced gamma ray emission (PIGE). Summary report of consultants' meeting

    International Nuclear Information System (INIS)

    Abriola, D.; Pedro de Jesus, A.

    2010-03-01

    A summary is given of a Consultants' Meeting assembled to assess the viability of a new IAEA Co-ordinated Research Project (CRP) on Development of nuclear data for PIGE for analytical applications. The need for such a CRP was strongly agreed. Both the technical discussions and the expected outcomes of such a project are described, along with detailed recommendations for implementation. The participants discussed the past and present status of the field and the experiments performed in their home institutes. Subsequently, they addressed the nuclear data needs for PIGE analysis and produced recommendations concerning the compilation, assessment, measurements, evaluation and benchmarking of cross-section data for PIGE as well as their inclusion in the existent IBANDL database. (author)

  1. Simultaneous PIXE and PIGE analyses of aerosol samples collected in urban areas

    International Nuclear Information System (INIS)

    Boni, C.; Caruso, E.; Cereda, E.; Marcazzan, G.M.; Redaelli, P.; Bacci, P.

    1988-01-01

    The paper concerns the simultaneous PIXE (Particle Induced X-ray Emission) and PIGE (Proton Induced Gamma-ray Emission) analyses of aerosol samples collected in urban areas. The results show that PIGE can detect Li, F, Na, Al, and Si in fly ashes and F, Na, Al and Si in atmospheric aerosol. The PIXE-PIGE technique has also been applied to 80 samples of atmospheric particular matter collected above Milan during the winter and summer months of 1986/7, and the average values of concentrations and enrichment factors are given for the detected elements. (U.K.)

  2. Fluorine analysis of human dentin surrounding resin composite after fluoride application by μ-PIGE/PIXE analysis

    Science.gov (United States)

    Okuyama, Katsushi; Komatsu, Hisanori; Yamamoto, Hiroko; Pereira, Patricia N. R.; Bedran-Russo, Ana K.; Nomachi, Masaharu; Sato, Takahiro; Sano, Hidehiko

    2011-10-01

    The use of fluoride for the prevention of caries is based on the transformation of hydroxylapatite to fluoroapatite in the presence of fluoride ions, thereby strengthening tooth structure. Adhesion of dentin and resin composite (tooth-colored restoration material) requires a dentin bonding system, since resin composite is not able to adhere to dentin directly. Demineralization of dentin by acid etching is an important step in the dentin bonding system, however, demineralization also introduces weaknesses in tooth structure. If the demineralized dentin could be strengthened by the application of fluoride, then the dentin-resin composite bond strength might also improve. To test this hypothesis, the present study evaluated the influence of fluoride applications on the strength of the dentin-resin composite bond by (1) tensile strength testing analyses, (2) SEM analyses of tooth structure, and (3) detection of calcium (Ca) and fluorine (F) distribution patterns by micro proton-induced X-ray emission (μ-PIXE) and micro proton-induced gamma-ray emission (μ-PIGE) analyses conducted at the Takasaki Ion Accelerators for Advanced Radiation Application (TIARA) at the Takasaki Advanced Radiation Research Institute (TARRI). In this study, the dentin in extracted human molars was exposed by grinding and the dentin was etched with 35% phosphoric acid. Fluoride was applied at two concentrations, 0.022% (100 ppm F) and 2.21% (10,000 ppm F) NaF solution, for two time periods, 30 and 60 s, prior to bonding the resin composite with the treated dentin. Controls were prepared in the same manner, but without the fluoride application. Bond strength was measured with a micro-tensile testing unit, and the fluorine and calcium distributions at the interface between dentin and resin composite were detected by μ-PIGE and μ-PIXE analysis, respectively. Results indicate that the 10,000 ppm F applications resulted in higher bond strengths than observed in either the 100 ppm F applications or

  3. Fluorine analysis of human dentin surrounding resin composite after fluoride application by μ-PIGE/PIXE analysis

    International Nuclear Information System (INIS)

    Okuyama, Katsushi; Komatsu, Hisanori; Yamamoto, Hiroko; Pereira, Patricia N.R.; Bedran-Russo, Ana K.; Nomachi, Masaharu; Sato, Takahiro; Sano, Hidehiko

    2011-01-01

    The use of fluoride for the prevention of caries is based on the transformation of hydroxylapatite to fluoroapatite in the presence of fluoride ions, thereby strengthening tooth structure. Adhesion of dentin and resin composite (tooth-colored restoration material) requires a dentin bonding system, since resin composite is not able to adhere to dentin directly. Demineralization of dentin by acid etching is an important step in the dentin bonding system, however, demineralization also introduces weaknesses in tooth structure. If the demineralized dentin could be strengthened by the application of fluoride, then the dentin-resin composite bond strength might also improve. To test this hypothesis, the present study evaluated the influence of fluoride applications on the strength of the dentin-resin composite bond by (1) tensile strength testing analyses, (2) SEM analyses of tooth structure, and (3) detection of calcium (Ca) and fluorine (F) distribution patterns by micro proton-induced X-ray emission (μ-PIXE) and micro proton-induced gamma-ray emission (μ-PIGE) analyses conducted at the Takasaki Ion Accelerators for Advanced Radiation Application (TIARA) at the Takasaki Advanced Radiation Research Institute (TARRI). In this study, the dentin in extracted human molars was exposed by grinding and the dentin was etched with 35% phosphoric acid. Fluoride was applied at two concentrations, 0.022% (100 ppm F) and 2.21% (10,000 ppm F) NaF solution, for two time periods, 30 and 60 s, prior to bonding the resin composite with the treated dentin. Controls were prepared in the same manner, but without the fluoride application. Bond strength was measured with a micro-tensile testing unit, and the fluorine and calcium distributions at the interface between dentin and resin composite were detected by μ-PIGE and μ-PIXE analysis, respectively. Results indicate that the 10,000 ppm F applications resulted in higher bond strengths than observed in either the 100 ppm F applications or

  4. Fluorine analysis of human dentin surrounding resin composite after fluoride application by {mu}-PIGE/PIXE analysis

    Energy Technology Data Exchange (ETDEWEB)

    Okuyama, Katsushi, E-mail: katsu@den.hokudai.ac.jp [Graduate School of Dental Medicine, Hokkaido University, Department of Restorative Dentistry, Kita-13, Nishi-7, Kita-ku, Hokkaido, Sapporo 060-8586 (Japan) and School of Dentistry, University of North Carolina, Department of Operative Dentistry, 302 Brauer, CB 7450, Chapel Hill, NC 27599-7450 (United States); Komatsu, Hisanori [Graduate School of Dental Medicine, Hokkaido University, Department of Restorative Dentistry, Kita-13, Nishi-7, Kita-ku, Hokkaido, Sapporo 060-8586 (Japan); Yamamoto, Hiroko [Graduate School of Dentistry, Osaka University, 1-8 Yamada-Oka, Osaka, Suita 565-0871 (Japan); Pereira, Patricia N.R. [School of Dentistry, University of North Carolina, Department of Operative Dentistry, 302 Brauer, CB 7450, Chapel Hill, NC 27599-7450 (United States); Bedran-Russo, Ana K. [University of Illinois at Chicago, College of Dentistry, Department of Restorative Dentistry, 801 S. Paulina St., Chicago, IL 60612 (United States); Nomachi, Masaharu [Graduate School of Science, Osaka University, 1-1 Machikaneyama, Osaka, Toyonaka 560-0043 (Japan); Sato, Takahiro [TARRI, JAEA, Advanced Radiation Technology, 1233 Watanuki-machi, Gunma, Takasaki 370-1292 (Japan); Sano, Hidehiko [Graduate School of Dental Medicine, Hokkaido University, Department of Restorative Dentistry, Kita-13, Nishi-7, Kita-ku, Hokkaido, Sapporo 060-8586 (Japan)

    2011-10-15

    The use of fluoride for the prevention of caries is based on the transformation of hydroxylapatite to fluoroapatite in the presence of fluoride ions, thereby strengthening tooth structure. Adhesion of dentin and resin composite (tooth-colored restoration material) requires a dentin bonding system, since resin composite is not able to adhere to dentin directly. Demineralization of dentin by acid etching is an important step in the dentin bonding system, however, demineralization also introduces weaknesses in tooth structure. If the demineralized dentin could be strengthened by the application of fluoride, then the dentin-resin composite bond strength might also improve. To test this hypothesis, the present study evaluated the influence of fluoride applications on the strength of the dentin-resin composite bond by (1) tensile strength testing analyses, (2) SEM analyses of tooth structure, and (3) detection of calcium (Ca) and fluorine (F) distribution patterns by micro proton-induced X-ray emission ({mu}-PIXE) and micro proton-induced gamma-ray emission ({mu}-PIGE) analyses conducted at the Takasaki Ion Accelerators for Advanced Radiation Application (TIARA) at the Takasaki Advanced Radiation Research Institute (TARRI). In this study, the dentin in extracted human molars was exposed by grinding and the dentin was etched with 35% phosphoric acid. Fluoride was applied at two concentrations, 0.022% (100 ppm F) and 2.21% (10,000 ppm F) NaF solution, for two time periods, 30 and 60 s, prior to bonding the resin composite with the treated dentin. Controls were prepared in the same manner, but without the fluoride application. Bond strength was measured with a micro-tensile testing unit, and the fluorine and calcium distributions at the interface between dentin and resin composite were detected by {mu}-PIGE and {mu}-PIXE analysis, respectively. Results indicate that the 10,000 ppm F applications resulted in higher bond strengths than observed in either the 100 ppm F

  5. Investigation on trace and major elements in anti-asthmatic medicinal plants by PIXE and PIGE techniques

    Science.gov (United States)

    Bhanisana Devi, R. K.; Nandakumar Sarma, H.; Kumar, Sanjiv

    2015-01-01

    Five widely used anti-asthmatic medicinal plants of north-eastern region of India have been investigated by using Proton Induced X-ray Emission (PIXE) and Proton Induced Gamma ray Emission (PIGE) techniques. The elements namely K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se and Br were detected with different concentrations (in ppm level) by PIXE technique whereas light elements namely F, Na, Mg, Al, P and Cl by PIGE technique in the studied plants. No toxic heavy metals such as Hg, Pb, Cd were detected. Analysis was performed on thick targets (pellets) prepared using the powders of specimens through a series of processing steps. Thick targets of plant based Certified Reference Materials (CRMs) were served as standardization of PIXE and PIGE set up. The trace elements present in the studied plants have been correlated with their medicinal properties.

  6. Investigation on trace and major elements in anti-asthmatic medicinal plants by PIXE and PIGE techniques

    Energy Technology Data Exchange (ETDEWEB)

    Bhanisana Devi, R.K., E-mail: bhanisanark@gmail.com [Department of Physics, Manipur University, Canchipur 795003 (India); Nandakumar Sarma, H. [Department of Physics, Manipur University, Canchipur 795003 (India); Kumar, Sanjiv [National Centre for Compositional Characterization of Materials (NCCCM), Hyderabad 500062 (India)

    2015-01-15

    Five widely used anti-asthmatic medicinal plants of north-eastern region of India have been investigated by using Proton Induced X-ray Emission (PIXE) and Proton Induced Gamma ray Emission (PIGE) techniques. The elements namely K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se and Br were detected with different concentrations (in ppm level) by PIXE technique whereas light elements namely F, Na, Mg, Al, P and Cl by PIGE technique in the studied plants. No toxic heavy metals such as Hg, Pb, Cd were detected. Analysis was performed on thick targets (pellets) prepared using the powders of specimens through a series of processing steps. Thick targets of plant based Certified Reference Materials (CRMs) were served as standardization of PIXE and PIGE set up. The trace elements present in the studied plants have been correlated with their medicinal properties.

  7. Below-surface analysis of inclusions with PIXE and PIGE

    International Nuclear Information System (INIS)

    MacArthur, J.D.; Ma, X.P.; Palmer, G.R.; Anderson, A.J.; Clark, A.H.

    1990-01-01

    The composition of fluid inclusions in host minerals holds much information about the chemical environment of mineral formation. When solid inclusions are exposed through polishing, their content can readily be investigated with an electron or proton probe. However, with an electron probe, only the daughter minerals or the residue material left when a fluid inclusion is opened can be analyzed since electrons with energies of tens of keV cannot penetrate to the unexposed inclusion. On the other hand, proton beams of a few MeV can penetrate a few tens of μm of material and still be able to excite characteristic radiation. This phenomenon has been exploited for the analysis of subsurface inclusions. Ideally, standard petrographic sections are polished to that inclusions, targetted for analysis, are brought to within 10 μm of the surface. The overlying matrix reduces the sensitivity of PIXE for the elements of low Z such as Na and Al because of the attenuation of the X-rays. However, these elements, as well as elements of even lower Z, which cannot be analyzed with the electron probe, can readily be detected with PIGE at good sensitivity. (orig.)

  8. Direct Trace Element Analysis of Liquid Blood Samples by In-Air Ion Beam Analytical Techniques (PIXE-PIGE).

    Science.gov (United States)

    Huszank, Robert; Csedreki, László; Török, Zsófia

    2017-02-07

    There are various liquid materials whose elemental composition is of interest in various fields of science and technology. In many cases, sample preparation or the extraction can be complicated, or it would destroy the original environment before the analysis (for example, in the case of biological samples). However, multielement direct analysis of liquid samples can be realized by an external PIXE-PIGE measurement system. Particle-induced X-ray and gamma-ray emission spectroscopy (PIXE, PIGE) techniques were applied in external (in-air) microbeam configuration for the trace and main element determination of liquid samples. The direct analysis of standard solutions of several metal salts and human blood samples (whole blood, blood serum, blood plasma, and formed elements) was realized. From the blood samples, Na, P, S, Cl, K, Ca, Fe, Cu, Zn, and Br elemental concentrations were determined. The focused and scanned ion beam creates an opportunity to analyze very small volume samples (∼10 μL). As the sample matrix consists of light elements, the analysis is possible at ppm level. Using this external beam setup, it was found that it is possible to determine elemental composition of small-volume liquid samples routinely, while the liquid samples do not require any preparation processes, and thus, they can be analyzed directly. In the case of lower concentrations, the method is also suitable for the analysis (down to even ∼1 ppm level) but with less accuracy and longer measurement times.

  9. Analysis of Atorvastatin in Commercial Solid Drugs using the TT-PIGE Technique

    International Nuclear Information System (INIS)

    Younes, G; Zahraman, K; Nsouli, B; Bejjani, A; Mahmoud, R; El-Yazbi, F

    2008-01-01

    The quantification of the active ingredient (Al) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like LC-MS, UV spectrophotometry and other appropriate organic analytical methods. In the case of an active ingredient contains specific heteroatoms (F, S, Cl), elemental IBA techniques can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparations. This is an advantage when the number of sample is relatively large. In this work, we demonstrate the ability of the Thick Target PIGE technique for rapid and accurate quantification of low concentration AtorvastatinTM in three commercial anti-hyperlipidemic drugs (Lipitor, Liponorm and Storvas). (author)

  10. Analysis of Atorvastatin in Commercial Solid Drugs using the TT-PIGE Technique

    Energy Technology Data Exchange (ETDEWEB)

    Younes, G [Beirut Arab University, Faculty of Science, Chemistry Department Beirut (Lebanon); Zahraman, K; Nsouli, B; Bejjani, A [Lebanese Atomic Energy Commission, National Council for Scientific Research, Beirut (Lebanon); Mahmoud, R; El-Yazbi, F [Beirut Arab University, Faculty of Pharmacy, Department of Pharmaceutical and Analytical Chemistry, Beirut (Lebanon)

    2008-07-01

    The quantification of the active ingredient (Al) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like LC-MS, UV spectrophotometry and other appropriate organic analytical methods. In the case of an active ingredient contains specific heteroatoms (F, S, Cl), elemental IBA techniques can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparations. This is an advantage when the number of sample is relatively large. In this work, we demonstrate the ability of the Thick Target PIGE technique for rapid and accurate quantification of low concentration AtorvastatinTM in three commercial anti-hyperlipidemic drugs (Lipitor, Liponorm and Storvas). (author)

  11. Study of boron detection limit using the in-air PIGE set-up at LAMFI-USP

    International Nuclear Information System (INIS)

    Moro, M. V.; Silva, T. F.; Trindade, G. F.; Added, N.; Tabacniks, M. H.

    2014-01-01

    The quantification of small amounts of boron in materials is of extreme importance in different areas of materials science. Boron is an important contaminant and also a silicon dopant in the semiconductor industry. Boron is also extensively used in nuclear power plants, either for neutron shielding or for safety control and boron is an essential nutrient for life, either vegetable or animal. The production of silicon solar cells, by refining metallurgical-grade silicon (MG-Si) requires the control and reduction of several silicon contaminants to very low concentration levels. Boron is one of the contaminants of solar-grade silicon (SG-Si) that must be controlled and quantified at sub-ppm levels. In the metallurgical purification, boron quantification is usually made by Inductive Coupled Plasma Mass Spectrometry, (ICP-MS) but the results need to be verified by an independent analytical method. In this work we present the results of the analysis of silicon samples by Particle Induced Gamma-Ray Emission (PIGE) aiming the quantification of low concentrations of boron. PIGE analysis was carried out using the in-air external beam line of the Laboratory for Materials Analysis with Ion Beams (LAMFI-USP) by the 10 B(p,αγ( 7 Be nuclear reaction, and measuring the 429 keV γ-ray. The in-air PIGE measurements at LAMFI have a quantification limit of the order of 10 16 at/cm 2

  12. Study of boron detection limit using the in-air PIGE set-up at LAMFI-USP

    Science.gov (United States)

    Moro, M. V.; Silva, T. F.; Trindade, G. F.; Added, N.; Tabacniks, M. H.

    2014-11-01

    The quantification of small amounts of boron in materials is of extreme importance in different areas of materials science. Boron is an important contaminant and also a silicon dopant in the semiconductor industry. Boron is also extensively used in nuclear power plants, either for neutron shielding or for safety control and boron is an essential nutrient for life, either vegetable or animal. The production of silicon solar cells, by refining metallurgical-grade silicon (MG-Si) requires the control and reduction of several silicon contaminants to very low concentration levels. Boron is one of the contaminants of solar-grade silicon (SG-Si) that must be controlled and quantified at sub-ppm levels. In the metallurgical purification, boron quantification is usually made by Inductive Coupled Plasma Mass Spectrometry, (ICP-MS) but the results need to be verified by an independent analytical method. In this work we present the results of the analysis of silicon samples by Particle Induced Gamma-Ray Emission (PIGE) aiming the quantification of low concentrations of boron. PIGE analysis was carried out using the in-air external beam line of the Laboratory for Materials Analysis with Ion Beans (LAMFI-USP) by the 10B ( p ,αγ(7Be nuclear reaction, and measuring the 429 keV γ-ray. The in-air PIGE measurements at LAMFI have a quantification limit of the order of 1016 at/cm2.

  13. Quantification of total aluminium concentrations in food samples at trace levels by INAA and PIGE methods

    International Nuclear Information System (INIS)

    Nanda, Braja B.; Acharya, R.

    2017-01-01

    Total aluminium contents in various food samples were determined by Instrumental Neutron Activation Analysis (INAA) and Particle Induced Gamma-ray Emission (PIGE) methods. A total of 16 rice samples, collected from the field, were analyzed by INAA using reactor neutrons from Dhruva reactor. Whereas a total 17 spices collected from market, were analyzed by both INAA and PIGE methods in conjunction with high resolution gamma-ray spectrometry. Aluminium concentration values were found to be in the range of 19-845 mg kg -1 for spices and 15-104 mg kg -1 for rice samples. The methods were validated by analyzing standard reference materials (SRMs) form NIST. (author)

  14. Study of boron detection limit using the in-air PIGE set-up at LAMFI-USP

    Energy Technology Data Exchange (ETDEWEB)

    Moro, M. V.; Silva, T. F.; Trindade, G. F.; Added, N.; Tabacniks, M. H. [Institute of Physics, University of São Paulo, SP (Brazil)

    2014-11-11

    The quantification of small amounts of boron in materials is of extreme importance in different areas of materials science. Boron is an important contaminant and also a silicon dopant in the semiconductor industry. Boron is also extensively used in nuclear power plants, either for neutron shielding or for safety control and boron is an essential nutrient for life, either vegetable or animal. The production of silicon solar cells, by refining metallurgical-grade silicon (MG-Si) requires the control and reduction of several silicon contaminants to very low concentration levels. Boron is one of the contaminants of solar-grade silicon (SG-Si) that must be controlled and quantified at sub-ppm levels. In the metallurgical purification, boron quantification is usually made by Inductive Coupled Plasma Mass Spectrometry, (ICP-MS) but the results need to be verified by an independent analytical method. In this work we present the results of the analysis of silicon samples by Particle Induced Gamma-Ray Emission (PIGE) aiming the quantification of low concentrations of boron. PIGE analysis was carried out using the in-air external beam line of the Laboratory for Materials Analysis with Ion Beams (LAMFI-USP) by the {sup 10}B(p,αγ({sup 7}Be nuclear reaction, and measuring the 429 keV γ-ray. The in-air PIGE measurements at LAMFI have a quantification limit of the order of 10{sup 16} at/cm{sup 2}.

  15. A code for quantitative analysis of light elements in thick samples by PIGE

    International Nuclear Information System (INIS)

    Mateus, R.; Jesus, A.P.; Ribeiro, J.P.

    2005-01-01

    This work presents a code developed for the quantitative analysis of light elements in thick samples by PIGE. The new method avoids the use of standards in the analysis, using a formalism similar to the one used for PIXE analysis, where the excitation function of the nuclear reaction related to the gamma-ray emission is integrated along the depth of the sample. In order to check the validity of the code, we present results for the analysis of Lithium, Boron, Fluorine and Sodium in thick samples. For this purpose, the experimental values of the excitation functions of the reactions 7 Li(p,p'γ) 7 Li, 10 B(p,αγ) 7 Be, 19 F(p,p'γ) 19 F and 23 Na(p,p'γ) 23 Na were used as input. For stopping power cross-sections calculations the semi-empirical equations of Ziegler et al. and the Bragg's rule were used. Agreement between the experimental and the calculated gamma-ray yields was always better than 7.5%

  16. Trace element finger printing of emeralds by PIXE and PIGE

    International Nuclear Information System (INIS)

    Ma Xinpei; Palmer, G.R.; MacArthur, J.D.

    1990-01-01

    The concentrations of 18 major- and minor-elements in 12 Emeralds from different mines and two synthetic ones are measured with proton induced X-ray emission (PIXE) and γ-ray emission (PIGE). The concentration and distribution of 18 elements are used to establish the characteristic finger print pattern of each Emerald. With the help of cluster analysis of SYSTAT statistical package for IBMPC, these finger prints are analysed, from which a quantitative description of the dissimilarities between Emeralds can be given

  17. Elemental analysis of river sediments by PIXE and PIGE

    International Nuclear Information System (INIS)

    Kennedy, V.J.; Augusthy, A.; Varier, K.M.; Magudapathy, P.; Panchapakesan, S.; Nair, K.G.M.; Vijayan, V.

    1999-01-01

    The Chaliyar river, located in Kerala, India has shown preoccupying pollution levels, that constitute a threat to public health and the ecological system. PIXE and PIGE techniques have been employed to measure the elemental concentrations in the river sediment samples. Thick targets were prepared out of the sediment samples collected from various sites along the course of the river. The measurements were carried out using 3 MeV proton beam obtained from 3 MV Tandem pelletron accelerator at Institute of Physics, Bhubaneswar. The elemental concentrations, especially that of heavy metals, at different sites are discussed in detail. Our results show that sediments from a site where the industrial activities are high are significantly high in concentrations of heavy metals (Cr, Ni, Cu, Zn, Hg and Pb) than those collected from non-industrial sites. The measured values are compared with the average composition of unpolluted river sediments and other national and international river sediments. (author)

  18. Analysis of glass from the post-Roman settlement Tonovcov grad (Slovenia) by PIXE–PIGE and LA-ICP-MS

    Energy Technology Data Exchange (ETDEWEB)

    Šmit, Ž., E-mail: ziga.smit@fmf.uni-lj.si [Faculty of Mathematics and Physics, University of Ljubljana, Jadranska 19, SI-1000 Ljubljana (Slovenia); Jožef Stefan Institute, Jamova 39, SI-1001 Ljubljana (Slovenia); Milavec, T. [Department of Archaeology, Faculty of Arts, University of Ljubljana, Zavetiška 5, SI-1000 Ljubljana (Slovenia); Fajfar, H. [Jožef Stefan Institute, Jamova 39, SI-1001 Ljubljana (Slovenia); Rehren, Th. [UCL Qatar, Education City, P.O. Box 23689, Doha (Qatar); Lankton, J.W. [UCL Institute of Archaeology, 31-34 Gordon Square, London WC1H 0PY (United Kingdom); Gratuze, B. [IRAMAT-Centre Ernest-Babelon, CNRS Université d’Orléans, 3D rue de la Ferollerie, 45071 Orléans Cedex 2 (France)

    2013-09-15

    The combined PIXE–PIGE method was used for the analysis of 43 glass fragments from the archaeological site Tonovcov grad in western Slovenia, with 10 of these additionally being analysed by LA-ICP-MS. The glass objects were attributed to the Late Antique production of the 4th–7th c. AD, with two examples of early Roman glass and three glass beads, one of them presumably of oriental origin. The analysis showed typical natron-type glass, produced in the Levantine region around the river Belus, and a few examples of HIMT glass, which could be recognized also in several other recycled objects. Only one glass bead, found in Early Medieval context, was made of the ash of halophytic plants.

  19. Fluorine analysis of human enamel around fluoride-containing materials under different pH-cycling by {mu}-PIGE/PIXE system

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, H., E-mail: kom@den.hokudai.ac.jp [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Yamamoto, H. [Graduate School of Dentistry, Osaka University, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Matsuda, Y.; Kijimura, T.; Kinugawa, M.; Okuyama, K. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Nomachi, M. [Graduate School of Science, Osaka University, 1-1 Machikaneyama, Toyonaka 560-0043 (Japan); Yasuda, K. [Wakasa Wan Energy Research Center, 64-52-1 Hase, Tsuruga 914-0192 (Japan); Satoh, T. [Advanced Radiation Technology, TARRI, JAEA, 1233 Watanuki-Machi, Takasaki 370-1292 (Japan); Oikawa, S. [National Institute of Radiological Science, 4-9-1, Anagawa, Inage-ku, Chiba 263-8555 (Japan)

    2011-10-15

    The caries preventive effect of fluoride-containing materials (FCMs) might depend on the caries risk of the individuals. Two pairs of demineralizing and remineralizing solutions of pH-cycling were prepared for simulating low and high caries risk. The purpose of this study was to determine fluorine (F) uptake into human enamel around FCMs under different pH-cycling using the in-air {mu}-PIGE/PIXE system. Fluoride-containing glass ionomer cement (Fuji IX{sub GP} FAST CAPSULE (FN)), and composite resin (BEAUTIFIL II with FLUORO BOND SHAKE ONE (BS)) were used in this study. The pH-cycling (pH 6.8-4.5) was carried out for 5 weeks. After pH-cycling, the caries progression was analyzed using transverse micro-radiography (TMR). The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the PIGE/PIXE system. From TMR analysis, there was a difference in caries risk between the two kinds of pH-cycling. Although the caries preventive effect of BS and FN was confirmed at low risk, the effect at high risk was confirmed for FN only. From the analysis of the fluorine uptake in the outer 200 {mu}m of the lesion we concluded that there was no significant difference between the pH-cycling solutions. However, we found different fluorine concentrations in the enamel for the two FCMs. The decreased caries progression under high risk for FN indicated that an adequate amount of fluorine supplied from the material is required at higher caries risk. It was confirmed that the caries preventive effect of FCM depends on the caries risk. The fluorine analysis of teeth under various pH-cycling conditions gives information to evaluate the caries preventive effect of fluoride-containing materials according to the caries risk.

  20. Fluorine analysis of human enamel around fluoride-containing materials under different pH-cycling by μ-PIGE/PIXE system

    International Nuclear Information System (INIS)

    Komatsu, H.; Yamamoto, H.; Matsuda, Y.; Kijimura, T.; Kinugawa, M.; Okuyama, K.; Nomachi, M.; Yasuda, K.; Satoh, T.; Oikawa, S.

    2011-01-01

    The caries preventive effect of fluoride-containing materials (FCMs) might depend on the caries risk of the individuals. Two pairs of demineralizing and remineralizing solutions of pH-cycling were prepared for simulating low and high caries risk. The purpose of this study was to determine fluorine (F) uptake into human enamel around FCMs under different pH-cycling using the in-air μ-PIGE/PIXE system. Fluoride-containing glass ionomer cement (Fuji IX GP FAST CAPSULE (FN)), and composite resin (BEAUTIFIL II with FLUORO BOND SHAKE ONE (BS)) were used in this study. The pH-cycling (pH 6.8-4.5) was carried out for 5 weeks. After pH-cycling, the caries progression was analyzed using transverse micro-radiography (TMR). The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the PIGE/PIXE system. From TMR analysis, there was a difference in caries risk between the two kinds of pH-cycling. Although the caries preventive effect of BS and FN was confirmed at low risk, the effect at high risk was confirmed for FN only. From the analysis of the fluorine uptake in the outer 200 μm of the lesion we concluded that there was no significant difference between the pH-cycling solutions. However, we found different fluorine concentrations in the enamel for the two FCMs. The decreased caries progression under high risk for FN indicated that an adequate amount of fluorine supplied from the material is required at higher caries risk. It was confirmed that the caries preventive effect of FCM depends on the caries risk. The fluorine analysis of teeth under various pH-cycling conditions gives information to evaluate the caries preventive effect of fluoride-containing materials according to the caries risk.

  1. Determination of trace concentrations of aluminium in rice samples by INAA and PIGE methods

    International Nuclear Information System (INIS)

    Nanda, B.B.; Biswal, R.R.; Acharya, R.; Pujari, P.K.

    2015-01-01

    Aluminium is one of the toxic elements entering human body mainly through food and food products. Though its bioavailability is very less, it is necessary to evaluate its total concentrations in food and food products entering to the body through. In order to evaluate total aluminium contents in various food items for daily dietary intake of aluminum, authors have systematically planned to carry out experiments in various food items including rice. Rice is the main food in many parts of India as well as in Odisha. Rice samples under study belong to three categories; (i) various rice samples from local market, (ii) various rice samples grown in similar irrigation (soil and water) conditions and (iii) same variety of rice with different irrigation conditions. Solid samples (pre-cleaned) were powdered, homogenized and taken for analysis by two nuclear analytical techniques (NATs) namely instrumental neutron activation analysis (INAA) using reactor neutrons at BARC and particle induced gamma ray emission (PIGE) using 4 MeV proton beam (20 nA current) from 3 MV Tandetron at IOP, Bhubaneswar in conjunction with high resolution gamma-ray spectrometry. Samples of 10-50 mg for INAA and 250 mg (pelletized in cellulose) for PIGE were used for experiments. For INAA, samples were irradiated at PCF, Dhruva reactor for 1 minute

  2. PIXE and PIGE analysis of pre-colonial pottery from Patanal - MS, Brazil

    International Nuclear Information System (INIS)

    Felicissimo, M.P.; Rodrigues-Filho, U.P.; Peixoto, J.L.; Barbosa, M.S.; Demortier, G.; Pireaux, J.J.

    2006-01-01

    PIXE and PIGE were applied to investigate the pottery from two archaeological sites located near the Brazil-Bolivia border in Pantanal, an area of natural preservation. The region was inhabited by ancient Amerindian tribes long before the Latin America colonization period and a deep understanding of their environment, cultural attributes and interconnections can only be achieved based on the study of archaeological findings. Multivariate statistical procedures were used to determine similarities and correlations between the analyzed samples and to indicate possible sources of raw material provenience. The results showed that traces of Cr, Cu and Ti and Na/Si and Mg/Si counting ratios were important to distinguish sherds from the archaeological sites MS-CP-71 and MS-CP-61. (author)

  3. Assessment of the usefulness of the PIGE method to determine nitrogen in human blood serum

    International Nuclear Information System (INIS)

    Kupila-Rantala, T.; Hyvoenen-Dabek, M.; Raiasanen, J.; Dabek, J.T.

    1995-01-01

    Proton-induced gamma-ray emission (PIGE) analysis has been applied to the determination of total nitrogen concentration of blood sera from hospital patients. Both the reaction 14 N(p,p'γ) 14 N, E γ =2313 keV, and the reaction 15 N(p,αγ) 12 C,E γ =4439keV, have been used. From 37 patients, the range of the nitrogen concentrations obtained was 9.54-16.3 g/l with a mean of 12.0 g/l. The corresponding total protein concentrations varied between 59 and 96 g/l, measured in a clinical laboratory auto analyser using the biuret method. The range of the albumin concentrations was 29-46 g/l. The nitrogen concentrations correlated well with the total protein concentrations (r=0.802). The multiple correlation of nitrogen versus (albumin+ (total protein- albumin)) gives a coefficient of 0.175 for albumin and 0.161 for total protein- albumin. The results agree with expectations and support the potential usefulness of the rapid PIGE method for medical studies. (author). 17 refs., 3 figs

  4. In vivo PIXE-PIGE study of enhanced retention of fluorine in tooth enamel after laser irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Demortier, Guy [Department of Physics, University of Namur, 61, rue de Bruxelles, B5000 Namur (Belgium)], E-mail: guy.demortier@tvcablenet.be; Nammour, Samir [Faculty of Medicine, University of Liege, 8, rue Paul Spaak, B-1000 Bruxelles (Belgium)

    2008-05-15

    The presence of fluoride in tooth enamel reduces the solubility of hydroxylapatite by acid attack. Fluoride presence (even at low concentration) in the oral cavity is efficient against caries process. We propose a new approach of the explanation of the increase of fluoride retention in the tooth enamel when low power laser irradiation is applied after the treatment with fluoride gel (fluoridation). External beam PIGE measurements of fluorine on extracted teeth have been made in order to determine the best sequence of the operations. The laser irradiation after fluoride application is more efficient than the reverse procedure. This observation is in agreement with previous observations that the fluorine penetration in the enamel takes place first in the soft organic material present between the polycrystalline (prismatic) structure before being integrated in the crystalline composition of hydroxylapatite in order to produce fluoro-apatite. As those in vitro measurements do not reflect the whole process in the saliva, in vivo PIGE measurements have been also performed. We have demonstrated, by repeating the PIGE measurements (at least five times at various time intervals) that a significant increase of the fluoride retention took place even 18 months after the unique laser treatment. The complete experimental procedure is described: fluoride application, laser irradiation, PIGE measurements with 2.7 MeV protons (repeated measurements at the same place on the same tooth in order to follow the evolution) and safety tests before in vivo analyses.

  5. Total CMB analysis of streaker aerosol samples by PIXE, PIGE, beta- and optical-absorption analyses

    International Nuclear Information System (INIS)

    Annegarn, H.J.; Przybylowicz, W.J.

    1993-01-01

    Multielemental analyses of aerosol samples are widely used in air pollution receptor modelling. Specifically, the chemical mass balance (CMB) model has become a powerful tool in urban air quality studies. Input data required for the CMB includes not only the traditional X-ray fluorescence (and hence PIXE) detected elements, but also total mass, organic and inorganic carbon, and other light elements including Mg, Na and F. The circular streaker sampler, in combination with PIXE analysis, has developed into a powerful tool for obtaining time-resolved, multielemental aerosol data. However, application in CMB modelling has been limited by the absence of total mass and complementary light element data. This study reports on progress in using techniques complementary to PIXE to obtain additional data from circular streaker samples, maintaining the nondestructive, instrumental approach inherent in PIXE: Beta-gauging using a 147 Pm source for total mass; optical absorption for inorganic carbon; and PIGE to measure the lighter elements. (orig.)

  6. Crystal structure of the catalytic domain of PigE: a transaminase involved in the biosynthesis of 2-methyl-3-n-amyl-pyrrole (MAP) from Serratia sp. FS14.

    Science.gov (United States)

    Lou, Xiangdi; Ran, Tingting; Han, Ning; Gao, Yanyan; He, Jianhua; Tang, Lin; Xu, Dongqing; Wang, Weiwu

    2014-04-25

    Prodigiosin, a tripyrrole red pigment synthesized by Serratia and some other microbes through a bifurcated biosynthesis pathway, MBC (4-methoxy-2,2'-bipyrrole-5-carbaldehyde) and MAP (2-methyl-3-n-amyl-pyrrole) are synthesized separately and then condensed by PigC to form prodigiosin. MAP is synthesized sequentially by PigD, PigE and PigB. PigE catalyzes the transamination of an amino group to the aldehyde group of 3-acetyloctanal, resulting in an aminoketone, which spontaneously cyclizes to form H2MAP. Here we report the crystal structure of the catalytic domain of PigE which involved in the biosynthesis of prodigiosin precursor MAP for the first time to a resolution of 2.3Å with a homodimer in the asymmetric unit. The monomer of PigE catalytic domain is composed of three domains with PLP as cofactor: a small N-terminal domain connecting the catalytic domain with the front part of PigE, a large PLP-binding domain and a C-terminal domain. The residues from both monomers build the PLP binding site at the interface of the dimer which resembles the other PLP-dependent enzymes. Structural comparison of PigE with Thermus thermophilus AcOAT showed a higher hydrophobic and smaller active site of PigE, these differences may be the reason for substrate specificity. Copyright © 2014 Elsevier Inc. All rights reserved.

  7. On the direct characterization and quantification of active ingredients in commercial solid drugs using PIXE, PIGE and TOF-SIMS techniques

    Energy Technology Data Exchange (ETDEWEB)

    Nsouli, B. [IBA laboratory, Lebanese Atomic Energy Commission (CNRS), Beirut (Lebanon)], E-mail: bnsouli@cnrs.edu.lb; Zahraman, K; Roumie, M [IBA laboratory, Lebanese Atomic Energy Commission (CNRS), Beirut (Lebanon); Yazbi, F [Faculty of Pharmacy, Department of Pharmaceutical Analytical Chemistry, Beirut Arab University, Beirut (Lebanon); Thomas, J P [Institut de Physique Nucleaire de Lyon, Universite Claude Bernard Lyon, Villeurbanne (France)

    2009-07-01

    The quantification of the active ingredient (AI) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like LC-MS, UV spectrophotometry and other appropriate organic analytical methods. In the case of an active ingredient contains specific heteroatoms (F, S, Cl, . . .), elemental IBA like PIXE and PIGE techniques, using small tandem accelerator of 1 - 2 MV, can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparations. This is an advantage when the number of sample is relatively large. In this work, we demonstrate the ability of the Thick Target PIXE and PIGE technique for rapid and accurate quantification of low concentration of different fluorinated, sulfured and chlorinated active ingredients in several commercial anti-hyperlipidemic and anti-inflammatory commercial drugs. In this work we will demonstrate the ability of PIXE and PIGE techniques for rapid and accurate quantification of Celecoxib and Atorvastatin active ingredients contained in several solid commercial drugs. The experimental aspects related to the quantification validity are presented and discussed. In addition, the Time of Flight Secondary Ion Emission using multicharged Ar ions with {approx} 10 MeV energy, delivered by a 4 MV Vander Graaf single stage accelerator, was used for structural and chemical analysis for some cases of binary commercial drugs containing two different active ingredients. The aspect of sample preparation and the role of excipient will be highlighted and discussed. (author)

  8. Analysis of minor elements in steel by coincidence method in deuteron-induced prompt gamma-ray emission (D-PIGE)

    International Nuclear Information System (INIS)

    Ene, Antoaneta; Popescu, I.; Badica, T.; Olariu, Agata; Besliu, C.

    2000-01-01

    Among the factors affecting the sensitivity of PIGE method (particle-induced prompt gamma-ray emission) frequently discussed in the literature, the background in the γ-ray spectrum holds a prominent place. In this work the limits of detection of minor elements in a standard steel sample (Euronorm rm No. 085/1) irradiated with 5 MeV deuterons have been determined by the regular d-PIGE method and with the selection of the (d,n) reaction channel by measuring γ--n coincidences following the reaction steel + deuterons. This approach has resulted in a significant improvement of the sensitivity of the analysis, reducing the background in prompt gamma ray spectrum by eliminating the γ--rays observed in the singular spectrum which arises from the reaction channels (d, d'), (d, γ), (d, p), (d, 3 He), (d, α) and (d, t). From the singular spectrum we could establish the presence of the elements S, Pb, Mo, Co, V, P, O, Si, Zn, Mn, Cu, Sb, C, Al, N, As, Ti and Fe. The γ--n coincidence spectrum, obtained as a result of the selection of the γ- transitions via the reaction channel (d, n), is substantially different from the singular γ--spectrum, exhibiting γ- lines of rather high intensity to be used in the analyses on a reduced background. The coincidence spectrum shows lines from S, Mo, Co, Zn, Si, Mn, V, Sb, Ti, As, Ni, Cr, P, O, Al, Cu and Fe. We also made a comparative study with the published results using 5.5 MeV protons as projectiles. While for a given energy of the protons not all the elements of interest lead to a (p, n) reaction (C, O, P, S, Si etc.), most of the (d, n) reactions are exoergic. On the other side, the identification of the elements is more difficult in the case of deuterons. (authors)

  9. A PIXE/PIGE study of gold mineralisation in lateritic terrain, Tanami Desert, Australia

    International Nuclear Information System (INIS)

    Van Moort, J.C.; Li, X.

    1997-01-01

    Proton induced X-ray and γ-ray emission (PIXE/PIGE) have been used to analyze major and trace elements in a suite of 140 core samples from around of the Jim's Find South gold anomaly in the Tanami desert, located in heavily weathered terrain. Simultaneous analyses were obtained for 30 elements, ranging in atomic number from 3 Li to 90 Th. The method was chosen because of its speed and the wide range of determination, its flexibility, precision and low detection limits. The regolith powder samples were treated by hot aqua regia before making them into pills. The PIXE/PIGE data of the acid insoluble residue give three factor analysis clusters. The first cluster comprises the elements F, Al, K, V, Mn, Fe, Ga, Rb, W and Au and is essentially related to sericitic wallrock alteration. The second cluster consists of Ti, As, Y, Zr, and Nb and is largely related to resistant minerals. The third cluster consists of Na, Ca and Sr and is interpreted to comprise elements in weatherable minerals such as feldspar and thus represents weathering intensity. While the Rb/K ratio and the product of As x Cu x Ni provide the best surface expression of the gold mineralisation, the Rb/AI ratio provides the best expression of the sericitic alteration around the ore body

  10. Trace element fingerprinting of emeralds by PIXE/PIGE

    International Nuclear Information System (INIS)

    Ma Xinpei; MacArthur, J.D.; Roeder, P.L.; Mariano, A.N.

    1993-01-01

    Gemologists consider the mineral beryl, beryllium aluminium silicate, to be the gem, emerald, when it contains sufficient chromium, >0.1%, to colour it a strong green. Emeralds usually contain other trace elements. To investigate the feasibility of distinguishing an emerald's country of origin through its trace content, the trace elements in emeralds and a few beryls from sixteen locations have been determined with a single nondestructive measurement using PIXE and PIGE. From the database established with this limited number of samples, distinguishing trace element patterns were found. (orig.)

  11. Compositional studies on Transylvanian gold nuggets: Advantages and limitations of PIXE-PIGE analysis

    International Nuclear Information System (INIS)

    Bugoi, Roxana; Cojocaru, Viorel; Constantinescu, Bogdan; Calligaro, Thomas; Pichon, Laurent; Roehrs, Stefan; Salomon, Joseph

    2008-01-01

    Minute fragments from nine gold nuggets from Transylvania - two belonging to placer deposits and seven to primary deposits - were analyzed by PIXE and PIGE at the AGLAE tandem accelerator of the Centre de Recherche et de Restauration des Musees de France (C2RMF) with a 3 MeV proton beam extracted into air. This study was triggered by some archaeological provenance issues for which the elemental characterization of the Transylvanian gold source, exploited from the Antiquity, was required. All analyzed Transylvanian gold nuggets are characterized by a consistently high amount of Ag (18% on average). Au and Ag add up to roughly 99%, the other elements - Cu, Fe, Te, Pb - being detected only at a trace level. The obtained results are in good agreement with the previous analyses of Transylvanian gold

  12. Standardization of a PIGE methodology for simultaneous quantification of low Z elements in barium borosilicate glass samples

    International Nuclear Information System (INIS)

    Chhillar, S.; Acharya, R.; Dasari, K.B.; Pujari, P.K.; Mishra, R.K.; Kaushik, C.P.

    2013-01-01

    In order to standardize particle induced gamma-ray emission (PIGE) methodology for simultaneous quantification of light elements, analytical sensitivities of Li, F, B, Na, Al and Si were evaluated using 4 MeV proton beam ( ∼ 10 nA current) using 3 MV Pelletron at IOP, Bhubaneswar. The PIGE method was validated by determining all six elements in a synthetic sample in graphite matrix and applied to two barium borosilicate glass (BaBSG) samples. The prompt γ-rays emitted from inelastic scattering or nuclear reactions of corresponding isotopes were measured using a 60% HPGe coupled to MCA and the current normalized count rates were used for concentration calculation. (author)

  13. PIXE/PIGE characterisation of emeralds using an external micro-beam

    International Nuclear Information System (INIS)

    Calligaro, T.; Dran, J.-C.; Poirot, J.-P.; Querre, G.; Salomon, J.; Zwaan, J.C.

    2000-01-01

    A large collection of emeralds of various occurrences has been analysed by PIXE/PIGE in view to establish a compositional database. Major elements (Be, Si, Al) and trace elements (Li, F, Na, Mg, Ca, Rb, Cs and transition metals) are determined using an external 3 MeV proton micro-beam. Elemental micro-mapping permits to select the useful provenance tracers. This database was applied to infer the origin of several ancient emeralds set on historical jewels

  14. PIGE as a screening tool for Per- and polyfluorinated substances in papers and textiles

    Science.gov (United States)

    Ritter, Evelyn E.; Dickinson, Margaret E.; Harron, John P.; Lunderberg, David M.; DeYoung, Paul A.; Robel, Alix E.; Field, Jennifer A.; Peaslee, Graham F.

    2017-09-01

    Per- and polyfluoroalkyl substances (PFASs) comprise a large array of man-made fluorinated chemicals. It is an emerging chemical class of concern because many PFASs are environmentally persistent and some have known ecological and human toxicity. Consumer products treated with PFASs result in human exposure to PFASs through inhalation, ingestion, and environmental exposure to emissions from wastewater or from landfills. A rapid screening method based on total fluorine was developed and applied to quantify PFASs on consumer papers and textiles. Particle-Induced Gamma Ray Emission (PIGE) spectroscopy provides a non-destructive and quantitative measurement of total fluorine on papers and textiles. This technique is both rapid and sensitive, with a limit of detection (LOD) of 13 nmol F/cm2 for papers and 24-45 nmol F/cm2 for textiles, with reproducibility of ±12% RSD for both. PIGE is a high throughput (>20 samples/hr typically) method that was applied to 50 papers and 50 textiles in commerce to demonstrate the method.

  15. Identification of lapis-lazuli pigments in paint layers by PIGE measurements

    Science.gov (United States)

    Grassi, N.; Migliori, A.; Mandò, P. A.; Calvo del Castillo, H.

    2004-06-01

    Lapis-lazuli is a semi-precious stone used in the past to produce a blue pigment. Its main component is lazurite, 3Na 2O·3Al 2O 3·6SiO 2·2Na 2S. The possibility of using PIXE to identify this pigment in canvas and wood painting is severely limited by the strong absorption of low-energy X-rays in the protective varnish and - when, as typical, the pigment is mixed with lead white - by the overlapping of Pb M lines with S K α. In this work we discuss the possibility of identifying lapis-lazuli by detecting sodium with PIGE. PIXE and PIGE measurements have been performed on samples containing lapis-lazuli mixed to lead white in different percentage, covered with polymeric foils to simulate the presence of varnish. At a percentage of lapis-lazuli below 50%, Na X-rays are hardly detectable even with the thinner foil; on the contrary the characteristic γ-rays are clearly detected down to about 1%. A first application has been successfully performed on the "Madonna dei fusi" by Leonardo da Vinci, in the framework of an extensive scientific investigation on the painting techniques used by the Renaissance genius.

  16. Evaluation of caries progression in dentin treated by fluoride-containing materials using an in-air micro-PIGE and micro-PIXE measurement system

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H., E-mail: yhiroko@dent.osaka-u.ac.jp [Department of Restorative Dentistry and Endodontology, Osaka University Graduate School of Dentistry, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Iwami, Y.; Yagi, K.; Hayashi, M. [Department of Restorative Dentistry and Endodontology, Osaka University Graduate School of Dentistry, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Komatsu, H.; Okuyama, K.; Matsuda, Y. [Graduate School of Dental Medicine, Hokkaido University, Kita 13, Nishi 7, Kita-ku, Sapporo 060-8586 (Japan); Yasuda, K. [The Wakasa Wan Energy Research Center, 64-52-1 Nagatani, Tsuruga 914-0192 (Japan)

    2015-04-01

    It is well-known that fluorine (F) is involved in the progression of caries. The evaluation of caries progression has conventionally been based on the change in mineral content using transverse microradiography (TMR). The purpose of this study was to evaluate the progression of dentinal caries by the change in calcium (Ca) content using Particle-Induced Gamma-ray Emission/Particle-Induced X-ray Emission (PIGE/PIXE) techniques at the Wakasa Wan Energy Research Center. We also assessed the relationship between caries progression rate and the concentration of F penetration into dentin from dental fluoride-containing materials (FCMs). Dentin sections of six extracted human teeth were prepared to obtain various amounts of F uptake using three types of FCMs. F and Ca distribution of specimens were obtained using PIGE/PIXE techniques. After evaluation, the specimens were immersed in 10 ml of demineralizing solution (pH 4.5) to simulate caries attack. To estimate caries progression rates, the same portions of the specimens were evaluated after caries attack treatment using PIGE/PIXE. A negative correlation between the F uptake in dentin and the rate of caries progression was observed. Therefore, caries progression in dentin was reduced by increasing the amount of F uptake from FCMs. This demonstrates that PIGE/PIXE techniques are valuable for estimating caries progression rates.

  17. Evaluation of caries progression in dentin treated by fluoride-containing materials using an in-air micro-PIGE and micro-PIXE measurement system

    International Nuclear Information System (INIS)

    Yamamoto, H.; Iwami, Y.; Yagi, K.; Hayashi, M.; Komatsu, H.; Okuyama, K.; Matsuda, Y.; Yasuda, K.

    2015-01-01

    It is well-known that fluorine (F) is involved in the progression of caries. The evaluation of caries progression has conventionally been based on the change in mineral content using transverse microradiography (TMR). The purpose of this study was to evaluate the progression of dentinal caries by the change in calcium (Ca) content using Particle-Induced Gamma-ray Emission/Particle-Induced X-ray Emission (PIGE/PIXE) techniques at the Wakasa Wan Energy Research Center. We also assessed the relationship between caries progression rate and the concentration of F penetration into dentin from dental fluoride-containing materials (FCMs). Dentin sections of six extracted human teeth were prepared to obtain various amounts of F uptake using three types of FCMs. F and Ca distribution of specimens were obtained using PIGE/PIXE techniques. After evaluation, the specimens were immersed in 10 ml of demineralizing solution (pH 4.5) to simulate caries attack. To estimate caries progression rates, the same portions of the specimens were evaluated after caries attack treatment using PIGE/PIXE. A negative correlation between the F uptake in dentin and the rate of caries progression was observed. Therefore, caries progression in dentin was reduced by increasing the amount of F uptake from FCMs. This demonstrates that PIGE/PIXE techniques are valuable for estimating caries progression rates

  18. A benchmarking procedure for PIGE related differential cross-sections

    Science.gov (United States)

    Axiotis, M.; Lagoyannis, A.; Fazinić, S.; Harissopulos, S.; Kokkoris, M.; Preketes-Sigalas, K.; Provatas, G.

    2018-05-01

    The application of standard-less PIGE requires the a priori knowledge of the differential cross section of the reaction used for the quantification of each detected light element. Towards this end, a lot of datasets have been published the last few years from several laboratories around the world. The discrepancies often found between different measured cross sections can be resolved by applying a rigorous benchmarking procedure through the measurement of thick target yields. Such a procedure is proposed in the present paper and is applied in the case of the 19F(p,p‧ γ)19F reaction.

  19. Summary report of the first research coordination meeting on development of a reference database for particle-induced gamma ray emission (PIGE) spectroscopy

    International Nuclear Information System (INIS)

    Abriola, D.; Pedro de Jesus, A.

    2011-07-01

    The First Research Coordination Meeting (RCM) of the IAEA Coordinated Research Project (CRP) on 'Development of a Reference Database for Particle-Induced Gamma-ray Emission (PIGE) Spectroscopy' was held at the IAEA, Vienna, from 16-20 May 2011. A summary of the participants' presentations is given as well as background information, objectives and recommendations concerning approach and methodology. The extension of the IBANDL database format to include PIGE data was discussed. The different tasks to achieve the CRP objectives were assigned to participants. A list of priority measurements was produced and the individual sets of measurements assigned to participants. (author)

  20. A Milliprobe for PIXE and PIGE Analysis used for the Study of Colour-Zoned Tourmaline

    Science.gov (United States)

    Mateus, R.; Alves, L. C.; Jesus, A. P.; Faria, A. F.; Ribeiro, J. P.

    2005-01-01

    A "milliprobe" system was implemented by using the focusing properties of a Van de Graaff accelerator, together with a collimator system including 1 mm diameter apertures, to impose the appropriate dimension to the beam spot. The scanning of the sample surface was achieved by X-Y movements of the sample holder (the Z axis being coincident with the beam direction). These movements were accomplished by a motorised X-Y table, with a travel of 25 mm × 25 mm, connected to the sample holder. This system was used to study specimens of the mineral tourmaline. Two samples, of the "watermelon" zoned tourmaline variety, originating from the Alto Ligonha pegmatite district in northern Mozambique, were analysed by the simultaneous use of PIXE (Proton-Induced X-Ray Emission) and PIGE (Proton-Induced Gamma-Ray Emission) techniques, in order to quantify their composition and try to establish a correlation between the elements (major and trace elements) and colour zoning. In order to validate the "milliprobe" analysis and study in more detail the frontier between zones of different colours, a microprobe analysis of the samples was also done. In this work, the mineralogical classification of the samples was accomplished. A correlation was established between the presence of Fe and green colour. It was also concluded that the presence of Mn by itself is not enough to lead to pink colour, which gives support to previous studies that claim that only Mn3+ and not the more common form Mn2+ is responsible for the pink colour.

  1. A Milliprobe for PIXE and PIGE Analysis used for the Study of Colour-Zoned Tourmaline

    Energy Technology Data Exchange (ETDEWEB)

    Mateus, R.; Alves, L.C.; Jesus, A.P.; Faria, A.F.; Ribeiro, J.P. [Univ. de Lisboa (Portugal). Centro de Fisica Nuclear

    2005-07-01

    A 'milliprobe' system was implemented by using the focusing properties of a Van de Graaff accelerator, together with a collimator system including 1mm diameter apertures, to impose the appropriate dimension to the beam spot. The scanning of the sample surface was achieved by X-Y movements of the sample holder (the Z axis being coincident with the beam direction). These movements were accomplished by a motorised X-Y table, with a travel of 25mmx25mm, connected to the sample holder. This system was used to study specimens of the mineral tourmaline. Two samples, of the 'watermelon' zoned tourmaline variety, originating from the Alto Ligonha pegmatite district in northern Mozambique, were analysed by the simultaneous use of PIXE (Proton-Induced X-Ray Emission) and PIGE (Proton-Induced Gamma-Ray Emission) techniques, in order to quantify their composition and try to establish a correlation between the elements (major and trace elements) and colour zoning. In order to validate the 'milliprobe' analysis and study in more detail the frontier between zones of different colours, a microprobe analysis of the samples was also done. In this work, the mineralogical classification of the samples was accomplished. A correlation was established between the presence of Fe and green colour. It was also concluded that the presence of Mn by itself is not enough to lead to pink colour, which gives support to previous studies that claim that only Mn{sup 3+} and not the more common form Mn{sup 2+} is responsible for the pink colour.

  2. A PIXE/PIGE study of lateritic gold mineralization from the regolith of the Mystery Zone, Mt Percy, Western Australia

    International Nuclear Information System (INIS)

    Li, X.; Van Moort, J.C.

    1998-01-01

    PIXE/PIGE have been utilized extensively in the search for gold and volcanic hosted massive sulphide deposits, using rock powders from relatively fresh rock. The present study uses regolith samples, from which weathering products (oxides, hydroxides, carbonates, sulphates and clay) have been removed by sequential treatment with aqua regia and sulphuric acid. The samples come from the Mystery Zone, Mt Percy, Kalgoorlie, comprising both mineralized and barren samples. The acid insoluble residue consist essentially of quartz with minor sericite. The PlXE/PIGE data from the acid insoluble residue shows that the geochemical character of W, Al, K, Ca, V, Ga, Rb, Rb/K and Rb/Al could correctly define the location of underlying mineralization at depth. The ratio of Ti/Zr remained relatively constant in different geological units and can be used to distinguish lithologies. (authors)

  3. A PIXE/PIGE study of lateritic gold mineralization from the regolith of the Mystery Zone, Mt Percy, Western Australia

    Energy Technology Data Exchange (ETDEWEB)

    Li, X.; Van Moort, J.C. [Tasmania Univ., Sandy Bay, TAS (Australia). Dept. of Geology

    1998-06-01

    PIXE/PIGE have been utilized extensively in the search for gold and volcanic hosted massive sulphide deposits, using rock powders from relatively fresh rock. The present study uses regolith samples, from which weathering products (oxides, hydroxides, carbonates, sulphates and clay) have been removed by sequential treatment with aqua regia and sulphuric acid. The samples come from the Mystery Zone, Mt Percy, Kalgoorlie, comprising both mineralized and barren samples. The acid insoluble residue consist essentially of quartz with minor sericite. The PlXE/PIGE data from the acid insoluble residue shows that the geochemical character of W, Al, K, Ca, V, Ga, Rb, Rb/K and Rb/Al could correctly define the location of underlying mineralization at depth. The ratio of Ti/Zr remained relatively constant in different geological units and can be used to distinguish lithologies. (authors). Extended abstract. 5 refs.

  4. Element analysis of teeth from children with and without cystic fibrosis by PIXE-PIGE

    International Nuclear Information System (INIS)

    Cua, F.T.

    1990-01-01

    The objective of this research is to determine whether there is a difference in the Ca, P, Fe, F, Mg, and Sr concentrations in teeth from children with and without cystic fibrosis (CF) as a function of age, sex of the child, maternal smoking habit, maternal drinking habit, and fluoridation of water supply. The nuclear analytical methods used were Proton-Induced X-Ray Emission (PIXE) and Proton-Induced Gamma Emission (PIGE). The findings are: (1) the concentration of Mg is higher in the teeth of children with cystic fibrosis who took antibiotics other than tetracycline (CF+NT) than in non-cystic fibrosis (NCF) teeth for the 'female' category; (2) P concentration is less in (CF+NT) teeth for the 'age greater than ten' group; (3) Fe concentration is greater for females in the NCF group; (4) Ca and Fe concentrations are lower for CF than for NCF in the 'mother smokes' group; (5) F and Sr concentrations for CF+NT are higher for the 'mother drinks' group than for the 'mother does not drink' group; (6) 'mother smokes' shows a depletion of Ca and Fe compared to 'mother does not smoke' for CF+NT. (7) 'fluoridation of water supply' shows an increase in F, except for NCF teeth. (author)

  5. Boron analysis for neutron capture therapy using particle-induced gamma-ray emission

    International Nuclear Information System (INIS)

    Nakai, Kei; Yamamoto, Yohei; Okamoto, Emiko; Yamamoto, Tetsuya; Yoshida, Fumiyo; Matsumura, Akira; Yamada, Naoto; Kitamura, Akane; Koka, Masashi; Satoh, Takahiro

    2015-01-01

    The neutron source of BNCT is currently changing from reactor to accelerator, but peripheral facilities such as a dose-planning system and blood boron analysis have still not been established. To evaluate the potential application of particle-induced gamma-ray emission (PIGE) for boron measurement in clinical boron neutron capture therapy, boronophenylalanine dissolved within a cell culture medium was measured using PIGE. PIGE detected 18 μgB/mL f-BPA in the culture medium, and all measurements of any given sample were taken within 20 min. Two hours of f-BPA exposure was required to create a boron distribution image. However, even though boron remained in the cells, the boron on the cell membrane could not be distinguished from the boron in the cytoplasm. - Highlights: • PIGE was evaluated for measuring blood boron concentration during clinical BNCT. • PIGE detected 18 μgB/mL f-BPA in culture medium. • All measurements of any given sample were taken within 20 min. • Two hours of f-BPA exposure is required to create boron distribution image by PIGE. • Boron on the cell membrane could not be distinguished from boron in the cytoplasm.

  6. An Apparatus For Student Projects Using External-Beam PIXE And PIGE

    International Nuclear Information System (INIS)

    Correll, Francis D.; Edsall, Douglas W.; DePooter, Katherine A.; Maskell, Nicholas D.; Vanhoy, Jeffrey R.

    2011-01-01

    We recently installed a simple endstation at the Naval Academy Tandem Accelerator Laboratory to support student projects using external-beam PIXE and PIGE. It consists of a short, graphite-lined beamline extension with a thin window, an interlocked box that surrounds the target, detectors for x- and gamma rays, provision for flooding the target with helium gas, easily changed x-ray absorbers, and a compact video camera for monitoring the position of the beam spot. We used this system to measure the elemental composition of colonial-era architectural materials, principally bricks and mortar, from James Madison's Montpelier, the reconstructed Virginia estate of the fourth President of the United States. We describe the design and construction of the system, relate some of our experiences using it, and present some preliminary data from our investigations.

  7. Trace elements in human, cattle and swine teeth, measured by external beam PIXE-PIGE setup

    International Nuclear Information System (INIS)

    Tabacniks, M.H.; Rizzutto, M.A.; Added, N.; Liguori Neto, R.; Acquadro, J.C.; Vilela, M.; Oliveira, T.R.C.F.; Markarian, R.A.; Mori, M.

    2001-01-01

    The use of animal teeth to replace human teeth in dentistry school classes and to test chemicals and fillings, motivated for a better characterization of the elementary composition of their enamel, since some of the chemical properties, adhesion and chemical compatibility may depend on these parameters. Cattle, swine and human teeth were collected by dentists of the University of Sao Paulo. These teeth came primarily from Sao Paulo region and were analyzed for trace elements at the Open Nuclear Physics Laboratory, using a high energy external proton beam, PIXE-PIGE setup

  8. On the direct quantification of celecoxib in commercial solid drugs using the TT-PIXE and TT-PIGE techniques

    International Nuclear Information System (INIS)

    Nsouli, B.; Zahraman, K.; Bejjani, A.; Assi, S.; El-Yazbi, F.; Roumie, M.

    2006-01-01

    The quantification of the active ingredient (AI) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like LC-MS, UV spectrophotometry and other appropriate organic analytical methods. In the case of an active ingredient contains specific heteroatoms (F, S, Cl, etc.,), elemental IBA technique can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparation. This is an advantage when the number of sample is relatively large. In this work, we demonstrate the ability of the thick target PIXE (TT-PIXE) and the TT-PIGE techniques for rapid and accurate quantification of celecoxib in commercial drugs. The experimental aspects related to the quantification validity are presented and discussed

  9. Determination of isotopic composition of boron in boron carbide by TIMS and PIGE: an inter-comparison study

    International Nuclear Information System (INIS)

    Sasibhushan, K.; Rao, R.M.; Parab, A.R.; Alamelu, D.; Aggarwal, S.K.; Acharya, R.; Chhillar, S.; Pujari, P.K.

    2015-01-01

    The paper reports a comparison of results on the determination of isotopic composition of boron in boron carbide (B 4 C) samples by Thermal Ionisation Mass Spectrometry (TIMS) and Particle Induced Gamma ray Spectrometry (PIGE). B 4 C samples having varying boron isotopic composition (natural, enriched with respect to 10 B) and their synthetic mixtures) have been analysed by both the techniques. The 10 B atom% was found to be in the range of 20-67%. (author)

  10. Application of PIGE to determine fluorine concentration in human teeth. Contribution to fluorosis study

    International Nuclear Information System (INIS)

    Salah, H.; Arab, N.

    2007-01-01

    Fluorosis, osteoselerosis, and systemic illness may result when tolerance levels of fluorine intake are exceeded. To avoid these abnormalities, we shall be aware of the mechanisms of their development. For this, quantitative results gathered from different parts of the world are necessary. In this paper, PIGE method is used to determine fluorine concentration in human teeth, collected from different regions of the Algerian Sahara. Both enamel and dentine regions were inspected. The external and internal mappings of the analyzed teeth have shown more variation in the localized fluorine concentration in dentine than in enamel, and the lowest level of fluorine concentration was observed in the frontier crown-root zone. The obtained results reveal relatively high fluorine concentration lying within the limit of fluorosis, according to the standardised grading dental fluorosis. (author)

  11. On the direct characterization and quantification of active ingredients in commercial solid drugs using PIXE, PIGE and ToF-SIMS techniques

    Energy Technology Data Exchange (ETDEWEB)

    Nsouli, B; Zahraman, K; Bejjani, A; Roumie, M; Noun, M [Ion Beam Analysis Laboratory, Lebanese Atomic Energy Commission - CNRS, P.O.Box: 11-8281 Beirut (Lebanon); Younes, G [Faculty of Sciences, Department of Chemistry - Beirut Arab University, Beirut (Lebanon); Assi, S; El-Yazbi, F; Mahmoud, R [Faculty of Pharmacy, Department of Pharmaceutical Analytical Chemistry - Beirut Arab University, Beirut (Lebanon); Thomas, J P [Institut de Physique Nucleaire de Lyon - Universite Claude Bernard Lyon 1 (France)

    2010-01-15

    The quantification of the active ingredient (AI) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like HPLC, LC-MS/MS, UV spectrophotometry and other appropriate organic analytical methods. In the case of an active ingredient contains specific heteroatoms (F, S, Cl, Br, ...), elemental IBA technique can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparation. This is an advantage when the number of sample is relatively large. In this work, we demonstrate the ability of the Thick target PIXE (TT-PIXE) and the TT-PIGE techniques for rapid and accurate quantification of celecoxib and atorvastatin in commercial solid drugs. The experimental aspects related to the quantification validity are presented and discussed. (author)

  12. On the direct characterization and quantification of active ingredients in commercial solid drugs using PIXE, PIGE and ToF-SIMS techniques

    International Nuclear Information System (INIS)

    Nsouli, B.; Zahraman, K.; Bejjani, A.; Roumie, M.; Noun, M.; Younes, G.; Assi, S.; El-Yazbi, F.; Mahmoud, R.; Thomas, J.P.

    2010-01-01

    The quantification of the active ingredient (AI) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like HPLC, LC-MS/MS, UV spectrophotometry and other appropriate organic analytical methods. In the case of an active ingredient contains specific heteroatoms (F, S, Cl, Br, ...), elemental IBA technique can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparation. This is an advantage when the number of sample is relatively large. In this work, we demonstrate the ability of the Thick target PIXE (TT-PIXE) and the TT-PIGE techniques for rapid and accurate quantification of celecoxib and atorvastatin in commercial solid drugs. The experimental aspects related to the quantification validity are presented and discussed. (author)

  13. Application of in situ current normalized PIGE method for determination of total boron and its isotopic composition

    International Nuclear Information System (INIS)

    Chhillar, Sumit; Acharya, R.; Sodaye, S.; Pujari, P.K.

    2014-01-01

    A particle induced gamma-ray emission (PIGE) method using proton beam has been standardized for determination of isotopic composition of natural boron and enriched boron samples. Target pellets of boron standard and samples were prepared in cellulose matrix. The prompt gamma rays of 429 keV, 718 keV and 2125 keV were measured from 10 B(p,αγ) 7 Be, 10 B(p, p'γ) 10 B and 11 B(p, p'γ) 11 B nuclear reactions, respectively. For normalizing the beam current variations in situ current normalization method was used. Validation of method was carried out using synthetic samples of boron carbide, borax, borazine and lithium metaborate in cellulose matrix. (author)

  14. Application of laser produced ion beams to nuclear analysis of materials

    International Nuclear Information System (INIS)

    Mima, K.; Fujita, K.; Azuma, H.; Yamazaki, A.; Kato, Y.; Okuda, C.; Ukyo, Y.; Sawada, H.; Gonzalez-Arrabal, R.; Perlado, J. M.; Nishimura, H.; Nakai, S.

    2013-01-01

    The ion beam driven nuclear analysis has been developed for many years by using various electrostatic accelerators. A proton micro-beam with the beam diameter of ∼1.5 μm at Takasaki Ion Acceleration for Advanced Radiation Application (TIARA), JAEA was used to analyze the positive electrode of the Li-ion battery with PIGE and PIXE. WThe PIGE and PIXE images of Li and Ni respectively for Li x Ni 0.8 Co 0.15 Al 0.05 O 2 (x = 0.75 ∼ 1.0) anodes have been taken. The PIGE images of Li x Ni 0.8 Co 0.15 Al 0.05 O 2 particles and the depth profile of the Li density have been obtained with high spatial resolution (a few μm). The images of the Li density distribution are very useful for the RandD of the Li ion battery. In order to make the in-situ ion beam analysis of the Li battery possible, a compact accelerator for a high quality MeV proton beam is necessary. Form this point of view, the diagnostics of Li ion battery is an appropriate field for the applications of laser produced ion beams. (authors)

  15. Elemental analysis techniques using proton microbeam

    International Nuclear Information System (INIS)

    Sakai, Takuro; Oikawa, Masakazu; Sato, Takahiro

    2005-01-01

    Proton microbeam is a powerful tool for two-dimensional elemental analysis. The analysis is based on Particle Induced X-ray Emission (PIXE) and Particle Induced Gamma-ray Emission (PIGE) techniques. The paper outlines the principles and instruments, and describes the dental application has been done in JAERI Takasaki. (author)

  16. Determination of Fluorine and other light elements in Syrian teeth by PIGE and PIXE techniques

    International Nuclear Information System (INIS)

    Bakraji, E.; Ahmad, M.; Doueer, M.

    2013-01-01

    The aim of this study is to determine the concentration of Fluorine in Syrian teeth collected from Southern and Coastal regions where both populations have almost similar dietary habits and similar occupational activities. The conventional PIGE method is used to determine Fluorine concentration in human teeth since its play an important role in bony and dental tissues, the low levels of Fluorine can play positive role against teeth cariosity and an inhibitor against certain enzyme systems, where high levels can cause dental Fluorosis and bone abnormalities for the bone structure. Several cations and anions have been studied in the drinking water of studied areas in order to investigate the role played by these elements and whether fluoridation within the normal levels of worldwide standard grading. Na, Mg, P and Ca concentrations have been determined in studied samples in order to compare with earlier works. (author)

  17. Conference on instrumental activation analysis IAA 92

    International Nuclear Information System (INIS)

    Frana, J.; Obrusnik, I.

    1992-05-01

    The publication contains 26 abstracts primarily concerned with neutron activation analysis, although other analytical techniques based on X-ray fluorescence analysis, PIXE, PIGE, RBS are also included. Some contributions deal with aspects of quality practice and assurance in radioanalytical laboratories, with marketing of instrumental neutron activation analysis services, with hard- and software aspects of radiation detection, etc. (Z.S.)

  18. Applications of laser produced ion beams to nuclear analysis of materials

    International Nuclear Information System (INIS)

    Mima, K.; Azuma, H.; Fujita, K.; Yamazaki, A.; Okuda, C.; Ukyo, Y.; Kato, Y.; Arrabal, R. Gonzalez; Soldo, F.; Perlado, J. M.; Nishimura, H.; Nakai, S.

    2012-01-01

    Laser produced ion beams have unique characteristics which are ultra-short pulse, very low emittance, and variety of nuclear species. These characteristics could be used for analyzing various materials like low Z ion doped heavy metals or ceramics. Energies of laser produced ion beam extend from 0.1MeV to 100MeV. Therefore, various nuclear processes can be induced in the interactions of ion beams with samples. The ion beam driven nuclear analysis has been developed for many years by using various electrostatic accelerators. To explore the applicability of laser ion beam to the analysis of the Li ion battery, a proton beam with the diameter of ∼ 1.0 μm at Takasaki Ion Acceleration for Advanced Radiation Application (TIARA), JAEA was used. For the analysis, the PIGE (Particle-Induced Gamma Ray Emission) is used. The proton beam scans over Li battery electrode samples to diagnose Li density in the LiNi 0.85 Co 0.15 O 2 anode. As the results, PIGE images for Li area density distributions are obtained with the spatial resolution of better than 1.5μm FWHM. By the Li PIGE images, the depth dependence of de-intercalation levels of Li in the anode is obtained. By the POP experiments at TIARA, it is clarified that laser produced ion beam is appropriate for the Li ion battery analysis. 41.85.Lc, 41.75.Jv, 42.62.cf.

  19. Determination of fluorine by proton induced gamma ray emission (PIGE) spectrometry in igneous and metamorphic charnockitic rocks from Rogaland (S.W. Norway)

    International Nuclear Information System (INIS)

    Roelandts, I.; Robaye, G.; Weber, G.; Delbrouck, J.M.; Duchesne, J.C.

    1986-01-01

    More than 200 specimens from different occurrences of the Rogaland igneous complex and surrounding granulite facies metamorphic rocks (S.W. Norway) have been analysed by a direct non-destructive proton induced gamma ray emission (PIGE) technique. The fluorine contents vary from < 25 ppm to 3500 ppm. There is a good correlation between the concentration of fluorine and that of phosphorus for igneous rocks, suggesting a control of apatite on the F content. In metamorphic rocks, amphibole and biotite besides apatite are the principal concentrations of fluorine indicating that fluorine in the system is controlled by granulite facies metamorphism conditions. (author)

  20. Summary Report of the 3rd Research Coordination Meeting on Development of a Reference Database for Particle-Induced Gamma ray Emission (PIGE) Spectroscopy

    International Nuclear Information System (INIS)

    Dimitriou, P.; Pedro de Jesus, A.

    2014-05-01

    The Third Research Coordination Meeting (RCM) of the IAEA Coordinated Research Project (CRP) on “Development of a Reference Database for Particle-Induced Gamma-ray Emission (PIGE) Spectroscopy” was held at the IAEA, Vienna, from 7 to 11 April 2014. Participants reviewed the progress made since the previous RCM and agreed upon the work that remains to be done by the end of the CRP. The contents of the final Technical Document were discussed and individual chapters were assigned. The summaries of participants’ presentations as well as the technical discussions and the list of assigned tasks are included in this report. (author)

  1. A combined PIXE-PIGE approach for the assessment of the diagenetic state of cremated bones submitted to AMS radiocarbon dating

    Science.gov (United States)

    Quarta, Gianluca; Calcagnile, Lucio; D'Elia, Marisa; Maruccio, Lucio; Gaballo, Valentina; Caramia, Annalisa

    2013-01-01

    Bone samples from a Bronze age necropolis in Northern Italy, exposed to different combustion temperatures, were submitted to XRD (X-ray Diffraction), PIXE (Particle Induced X-ray Emission) and PIGE (Particle Induced Gamma Ray Emission) analyses in order to obtain information about their diagenetic state. Structural carbonate was then extracted by acid hydrolysis and used for 14C-AMS (Accelerator Mass Spectrometry) dating. These analytical techniques permitted the study of the effects of the combustion temperature on the crystallinity of the bone apatite and on its elemental chemical composition in terms of major, minor and trace elements. The results indicate that combustion at temperatures above ∼700 °C induces changes in the bone crystalline structure, reducing the diagenetic uptake of elements from the burial environment.

  2. A combined PIXE-PIGE approach for the assessment of the diagenetic state of cremated bones submitted to AMS radiocarbon dating

    Energy Technology Data Exchange (ETDEWEB)

    Quarta, Gianluca, E-mail: gianluca.quarta@unisalento.it [CEDAD-Department of Engineering for Innovation, University of Salento, via per Monteroni, 73100 Lecce (Italy); Calcagnile, Lucio; D' Elia, Marisa; Maruccio, Lucio; Gaballo, Valentina; Caramia, Annalisa [CEDAD-Department of Engineering for Innovation, University of Salento, via per Monteroni, 73100 Lecce (Italy)

    2013-01-15

    Bone samples from a Bronze age necropolis in Northern Italy, exposed to different combustion temperatures, were submitted to XRD (X-ray Diffraction), PIXE (Particle Induced X-ray Emission) and PIGE (Particle Induced Gamma Ray Emission) analyses in order to obtain information about their diagenetic state. Structural carbonate was then extracted by acid hydrolysis and used for {sup 14}C-AMS (Accelerator Mass Spectrometry) dating. These analytical techniques permitted the study of the effects of the combustion temperature on the crystallinity of the bone apatite and on its elemental chemical composition in terms of major, minor and trace elements. The results indicate that combustion at temperatures above {approx}700 Degree-Sign C induces changes in the bone crystalline structure, reducing the diagenetic uptake of elements from the burial environment.

  3. Micro-PIGE determination of fluorine distribution in developing hamster tooth germs

    International Nuclear Information System (INIS)

    Lyaruu, D.M.; Lenglet, W.J.; Woeltgens, J.H.B.; Bronckers, A.L.

    1989-01-01

    A micro-PIGE (Proton-Induced gamma-ray Emission) technique based on the delayed 5/2+----1/2+ nuclear transition of fluorine (E gamma = 197 keV, t1/2 = 87 ns) emitted after 19 F(p,p', gamma) 19 F reaction was used to detect and study the distribution of fluorine in the developing enamel organ during pre-eruptive stages, i.e., the transitional to early maturation stages of enamel formation in neonatal hamsters administered a single IP dose of sodium fluoride (20 mg NaF/kg body weight). The aforementioned nuclear reaction is unique for fluorine, and therefore detection of gamma-rays emanating from this reaction in a biological specimen implies a positive identification of fluorine at that particular site. Calcium and phosphorus X-rays were also recorded and used as parameters for assessment of the relationship between the degree of mineralization and fluoride incorporation into the enamel organ. The highest fluorine concentration in the enamel organ was recorded in the dentin near the dentin-enamel junction (DEJ). In the enamel, the highest concentration of fluorine was found to be associated with the more mature areas of the enamel near the DEJ, but gradually decreased in the direction of the enamel surface. Fluorine was not detected in the control germs. These results suggest that administration of fluoride in high doses during the pre-eruptive stages of enamel formation leads to incorporation of the ion into the forming dentin and enamel mineral, and that the enamel matrix does not seem to bind fluoride avidly

  4. Development of a PIGE-Detection System for in-situ Inspection and Quality Assurance in the Evolution of Fast Rotating Parts in High Temperature Environment Manufactured from TiAl

    Directory of Open Access Journals (Sweden)

    S. Neve

    2013-04-01

    Full Text Available Intermetallic -titanium aluminides are a promising material in high temperature technologies. Their high specific strength at temperatures above 700°C offers the possibility for their use as components of aerospace and automotive industries. With a specific weight of 50% of that of the widely used Ni-based superalloys TiAl is very suitable as material for fast rotating parts like turbine blades in aircraft engines and land based power stations or turbocharger rotors. Thus lower mechanical stresses and a reduced fuel consumption and CO2-emission are expected. To overcome the insufficient oxidation protection the halogen effect offers an innovative way. After surface doping using F-implantation or liquid phase-treatment with an F-containing solution and subsequent oxidation at high temperatures the formation of a protective alumina scale can be achieved. By using non-destructive ion beam analyses (PIGE, RBS F was found at the metal/oxide interface. For analysis of large scale components a new vacuum chamber at the IKF was installed and became operative. With this prototype of in-situ quality assurance system for the F-doping of manufactured parts from TiAl some performance test measurements were done and presented in this paper

  5. Development of a PIGE-Detection System for in-situ Inspection and Quality Assurance in the Evolution of Fast Rotating Parts in High Temperature Environment Manufactured from TiAl

    International Nuclear Information System (INIS)

    Neve, S.; Zschau, H. E.; Masset, P.J.; Schütze, M.

    2013-01-01

    Intermetallic γ-titanium aluminides are a promising material in high temperature technologies. Their high specific strength at temperatures above 700 O C offers the possibility for their use as components of aerospace and automotive industries. With a specific weight of 50% of that of the widely used Ni-based superalloys TiAl is very suitable as material for fast rotating parts like turbine blades in aircraft engines and land based power stations or turbocharger rotors. Thus lower mechanical stresses and a reduced fuel consumption and CO 2 -emission are expected. To overcome the insufficient oxidation protection the halogen effect offers an innovative way. After surface doping using F-implantation or liquid phase-treatment with an F-containing solution and subsequent oxidation at high temperatures the formation of a protective alumina scale can be achieved. By using non-destructive ion beam analyses (PIGE, RBS) F was found at the metal/oxide interface. For analysis of large scale components a new vacuum chamber at the IKF was installed and became operative. With this prototype of in-situ quality assurance system for the F-doping of manufactured parts from TiAl some performance test measurements were done and presented in this paper. (author)

  6. Particle-Induced Gamma-ray Emission Spectroscopy Over a Broad Range of Elements

    Science.gov (United States)

    Olds, Hannah; Wilkinson, John; Tighe, Meghanne; McLallen, Walter; McGuire, Patrick

    2017-09-01

    Ion beam analysis is a common application of nuclear physics that allows elemental and isotopic information about materials to be determined from accelerated light ion beams One of the best know ion beam analysis techniques is Particle-Induced Gamma-ray Emission (PIGE) spectroscopy, which can be used ex vacuo to identify the elements of interest in almost any solid target. The energies of the gamma-rays emitted by excited nuclei will be unique to each element and depend on its nuclear structure. For the most sensitivity, the accelerated ions should exceed the Coulomb barrier of the target, but many isotopes are known to be accessible to PIGE even below the Coulomb barrier. To explore the sensitivity of PIGE across the periodic table, PIGE measurements were made on elements with Z = 5, 9, 11-15, 17, 19-35, 37, 42, 44-48, 53, 56, 60, 62, 73, and 74 using 3.4 MeV protons. These measurements will be compared with literature values and be used as a basis for comparison with higher-energy proton beams available at the University of Notre Dame's St. Andre accelerator when it comes online this Fall. The beam normalization technique of using atmospheric argon and its 1459 keV gamma-ray to better estimate the integrated beam on target will also be discussed. Funded by the NSF REU program and the University of Notre Dame.

  7. Temporal changes in elemental composition in decomposing filamentous algae (Cladophora glomerata and Pilayella littoralis) determined with PIXE and PIGE

    Energy Technology Data Exchange (ETDEWEB)

    Lill, J.-O., E-mail: jlill@abo.fi [Accelerator Laboratory, Turku PET Centre, Abo Akademi University, Porthansg. 3, FI-20500 Turku (Finland); Department of Natural Sciences, Abo Akademi University, Porthansg. 3, FI-20500 Turku (Finland); Salovius-Lauren, S. [Department of Biosciences, Abo Akademi University, Artillerig. 6, FI-20520 Turku (Finland); Harju, L. [Department of Chemical Engineering, Abo Akademi University, Biskopsg. 8, FI-20500 Turku (Finland); Rajander, J. [Accelerator Laboratory, Turku PET Centre, Abo Akademi University, Porthansg. 3, FI-20500 Turku (Finland); Department of Chemical Engineering, Abo Akademi University, Biskopsg. 8, FI-20500 Turku (Finland); Saarela, K.-E. [Department of Chemical Engineering, Abo Akademi University, Biskopsg. 8, FI-20500 Turku (Finland); Lindroos, A. [Department of Natural Sciences, Abo Akademi University, Porthansg. 3, FI-20500 Turku (Finland); Heselius, S.-J. [Accelerator Laboratory, Turku PET Centre, Abo Akademi University, Porthansg. 3, FI-20500 Turku (Finland)

    2012-01-01

    Particle-induced X-ray emission and particle-induced gamma-ray emission spectrometry were successfully applied in a study of the elemental composition of decomposing filamentous algae. Fresh brown (Pilayella littoralis) and green (Cladophora glomerata) algal materials were placed in cages at 4 m depth in a water column of 8 m in the Archipelago Sea, northern Baltic Sea. Every second week decaying algae were sampled from the cages to allow measurements of changes in the elemental compositions. In the study of the elemental losses the concentrations were compensated for the mass reduction. The results show that sulphur, chlorine and partly potassium were lost during decomposition of P. littoralis and C. glomerata. Most of the other elements studied were recovered in the remaining algal mass. Special attention was paid to sorption and desorption of elements, including metal binding capacity, in the decaying algal materials. The affinity order of different cations to the two algal species was established by calculation of conditional distribution coefficients, D Prime {sub M}. For instance for P. littoralis the following series of binding strength (affinity) of cations were obtained: Al > Ti > Fe Much-Greater-Than Mn > Ni, Cu > Ba, Cr, Zn Much-Greater-Than Rb > K, Sr > Pb Much-Greater-Than Ca Much-Greater-Than Na > Mg. Notably is that the binding strength of strontium was more than 10 times higher for P. littoralis than for C. glomerata. Due to their high binding capacity and good affinity and selectivity for heavy metal ions these algae have great potential as biological sorbents. Large variations in elemental content during decomposition complicate the use of algae for environmental monitoring. - Highlights: Black-Right-Pointing-Pointer Elemental concentrations in P. littoralis and C. glomerata from the Archipelago Sea in Finland were measured during decomposition. Black-Right-Pointing-Pointer PIXE and PIGE were successfully used for chemical analysis of 24 elements

  8. Temporal changes in elemental composition in decomposing filamentous algae (Cladophora glomerata and Pilayella littoralis) determined with PIXE and PIGE

    International Nuclear Information System (INIS)

    Lill, J.-O.; Salovius-Laurén, S.; Harju, L.; Rajander, J.; Saarela, K.-E.; Lindroos, A.; Heselius, S.-J.

    2012-01-01

    Particle-induced X-ray emission and particle-induced gamma-ray emission spectrometry were successfully applied in a study of the elemental composition of decomposing filamentous algae. Fresh brown (Pilayella littoralis) and green (Cladophora glomerata) algal materials were placed in cages at 4 m depth in a water column of 8 m in the Archipelago Sea, northern Baltic Sea. Every second week decaying algae were sampled from the cages to allow measurements of changes in the elemental compositions. In the study of the elemental losses the concentrations were compensated for the mass reduction. The results show that sulphur, chlorine and partly potassium were lost during decomposition of P. littoralis and C. glomerata. Most of the other elements studied were recovered in the remaining algal mass. Special attention was paid to sorption and desorption of elements, including metal binding capacity, in the decaying algal materials. The affinity order of different cations to the two algal species was established by calculation of conditional distribution coefficients, D′ M . For instance for P. littoralis the following series of binding strength (affinity) of cations were obtained: Al > Ti > Fe ≫ Mn > Ni, Cu > Ba, Cr, Zn ≫ Rb > K, Sr > Pb ≫ Ca ≫ Na > Mg. Notably is that the binding strength of strontium was more than 10 times higher for P. littoralis than for C. glomerata. Due to their high binding capacity and good affinity and selectivity for heavy metal ions these algae have great potential as biological sorbents. Large variations in elemental content during decomposition complicate the use of algae for environmental monitoring. - Highlights: ► Elemental concentrations in P. littoralis and C. glomerata from the Archipelago Sea in Finland were measured during decomposition. ► PIXE and PIGE were successfully used for chemical analysis of 24 elements. ► The chemical affinity of different elements to the algae was established by calculation of conditional

  9. Light ion microbeam analysis / processing system and its improvement

    International Nuclear Information System (INIS)

    Koka, Masashi; Ishii, Yasuyuki; Yamada, Naoto; Ohkubo, Takeru; Kamiya, Tomihiro; Satoh, Takahiro; Kada, Wataru; Kitamura, Akane; Iwata, Yoshihiro

    2016-03-01

    A MeV-class light ion microbeam system has been developed for micro-analysis and micro-fabrication with high spatial resolution at 3-MV single-ended accelerator in Takasaki Ion Accelerators for Advanced Radiation Application of Takasaki Advanced Radiation Research Institute, Sector of Nuclear Science Research, Japan Atomic Energy Agency. This report describes the technical improvements for the main apparatus (the accelerator, beam-transport lines, and microbeam system), and auxiliary equipments/ parts for ion beam applications such as Particle Induced X-ray/Gamma-ray Emission (PIXE/PIGE) analysis, 3-D element distribution analysis using PIXE Computed Tomography (CT), Ion Beam Induced Luminescence (IBIL) analysis, and Proton Beam Writing with the microbeam scanning, with functional outline of these apparatus and equipments/parts. (author)

  10. Determination of total fluorine in five coal reference materials by proton-induced gamma-ray emission spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Roelandts, I.; Robaye, G.; Delbrouck-Habaru, J.M.; Weber, G. [University of Liege, Sart (Belgium). Dept. of Geology, Petrology and Geochemistry

    1996-03-01

    The direct non-destructive proton-induced gamma-ray emission (PIGE) technique with a germanium detector was applied to the determination of total fluorine concentration in five coal reference materials (BCR 30, NIST 1632b, NIST 1635, SARM 20 and USGS CLB-1). Duplicate analyses were made from five randomly selected bottles of each coal. Individual data are presented and some problems (calibration, proton stopping power, effects of sample heating by the proton beam, background estimation) which were encountered during this study are discussed. Sensitivity and reproducibility of the determinations, and homogeneity of the coal samples with respect to fluorine contents by analysis of variance were investigated. The present data are also compared with the few published values for these reference samples, including other PIGE data. The use of synthetic standards and spiked samples in the present study suggested that the PIGE method was more accurate than other techniques.

  11. Rapid rock analysis and microprobe scanning of dermatological material using proton-induced x-ray and γ-ray emission

    International Nuclear Information System (INIS)

    Carlsson, L.E.

    1983-01-01

    The dissertation report comprises 6 articles that have or will appear in open literature. The use of PIXE and PIGE analysis techniques on geological materials, and also on drill cores, is discussed. The accuracy of the methods have been tested on standards. The effect of sample thickness has been studied. A proton microprobe has been compared with an electron microprobe on human skin sections. Both probes give highly reproducible results, but a small systematic deviation between the probes is found. (author)

  12. The upgraded external-beam PIXE/PIGE set-up at LABEC for very fast measurements on aerosol samples

    Energy Technology Data Exchange (ETDEWEB)

    Lucarelli, F.; Calzolai, G.; Chiari, M.; Mochi, D.; Nava, S. [Department of Physics, University of Florence and INFN, Florence (Italy)

    2013-07-01

    Full text: Particle Induced X-ray Emission (PIXE)technique has been widely used since its birth for the study of the aerosol composition, and for a long time it has been the dominating technique for its elemental analysis. However now it has to compete with other techniques, like Induced Coupled Plasma and detection by Atomic Emission Spectroscopy (ICP-AES) or Mass Spectrometry (ICP-MS) or Synchrotron Radiation XRF (SR-XRF). To remain competitive, a proper experimental set-up is important to fully exploit PIXE capabilities. At LABEC, an external beam line is fully dedicated to PIXE-PIGE measurements of atmospheric aerosols [1]. Recently SDD (Silicon Drift Detectors) have been introduced for X-ray detection thanks to their better resolution with respect to Si(Li) detectors and the possibility of managing high counting rates (up to 50 kHz at 0.5 μsec shaping time). This implies, in turn, the possibility of using very high beam currents thus drastically reducing the measurement time. However their use for a complete characterization of X-rays was limited by the small thickness and surface areas available. Now SDD with a thickness of 500 μm and 80 mm{sup 2} area have been introduced in the market. We have therefore replaced the Si(Li) detector used so far for the detection of medium-high Z elements with such a SDD. A comparison of the two detectors has been carried out; PIXE minimum detection limits (MDLs) at different proton beam energies have been studied to find out the best energy for PIXE measurements on aerosol samples collected on different substrata, namely Teflon, Kapton, Nuclepore and Kimfol, used for daily or hourly sampling or for cascade impactors. In particular in the case of Teflon filters, the production of γ-rays by F in the Teflon filter limits the current which may be used and the Compton γ-ray background worsens the MDLs. Due to the lower thickness of the SDD detector with respect to a typical Si(Li) detector, these problems are reduced

  13. Development of a Reference Database for Particle-Induced Gamma-ray Emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Dimitriou, P., E-mail: P.Dimitriou@iaea.org [International Atomic Energy Agency, Wagramerstrasse 5, A-1400 Vienna (Austria); Becker, H.-W. [Ruhr Universität Bochum, Gebäude NT05/130, Postfach 102148, Bochum 44721 (Germany); Bogdanović-Radović, I. [Department of Experimental Physics, Institute Rudjer Boskovic, Bijenicka Cesta 54, 10000 Zagreb (Croatia); Chiari, M. [Istituto Nazionale di Fisica Nucleare, Via Sansone 1, Sesto Fiorentino, 50019 Firenze (Italy); Goncharov, A. [Kharkov Institute of Physics and Technology, National Science Center, Akademicheskaya Str.1, Kharkov 61108 (Ukraine); Jesus, A.P. [Departamento de Física, Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa (Portugal); Kakuee, O. [Nuclear Science and Technology Research Institute, End of North Karegar Ave., PO Box 14395-836, Tehran (Iran, Islamic Republic of); Kiss, A.Z. [Institute of Nuclear Research (ATOMKI), Bem ter 18/c, PO Box 51, 4001 Debrecen (Hungary); Lagoyannis, A. [National Center of Scientific Research “Demokritos”, Agia Paraskevi, P.O. Box 60228, 15310 Athens (Greece); Räisänen, J. [Division of Materials Physics, Department of Physics, University of Helsinki, PO Box 43, 00014 University of Helsinki (Finland); Strivay, D. [Institut de Physique Nucleaire, Atomique et de Spectroscopie, Universite de Liège, Sart Tilman, B15 4000 Liège (Belgium); Zucchiatti, A. [Centro de Micro Análisis de Materiales, Universidad Autónoma de Madrid, Faraday 3, Madrid 28049 (Spain)

    2016-03-15

    Particle-Induced Gamma-ray Emission (PIGE) is a powerful analytical technique that exploits the interactions of rapid charged particles with nuclei located near a sample surface to determine the composition and structure of the surface regions of solids by measurement of characteristic prompt γ rays. The potential for depth profiling of this technique has long been recognized, however, the implementation has been limited owing to insufficient knowledge of the physical data and lack of suitable user-friendly computer codes for the applications. Although a considerable body of published data exists in the nuclear physics literature for nuclear reaction cross sections with γ rays in the exit channel, there is no up-to-date, comprehensive compilation specifically dedicated to IBA applications. A number of PIGE cross-section data had already been uploaded to the Ion Beam Analysis Nuclear Data Library (IBANDL) ( (http://www-nds.iaea.org/ibandl)) by members of the IBA community by 2011, however a preliminary survey of this body of unevaluated experimental data has revealed numerous discrepancies beyond the uncertainty limits reported by the authors. Using the resources and coordination provided by the IAEA, a concerted effort to improve the situation was made within the Coordinated Research Project on the Development of a Reference Database for PIGE spectroscopy, from 2011 to 2015. The aim of the CRP was to create a data library for Ion Beam Analysis that contains reliable and usable data on charged particle γ-ray emission cross sections that would be made freely available to the user community. As the CRP has reached its completion, we shall present its main achievements, including the results of nuclear cross-section evaluations and the development of a computer code that will become available to the public allowing for the implementation of a standardless PIGE technique.

  14. OLDAPS - obsidian least destructive analysis provenancing system: an application study

    International Nuclear Information System (INIS)

    Eder, F.

    2013-01-01

    The natural volcanic glass obsidian is one of the classical objects of archaeometric analyses. Obsidian is generally described as a relatively homogeneous material and although the number of applicable geological sources is limited, numerous obsidian finds have been found all over the world far away from any natural outcrop. Reliable provenancing by means of the highly specific chemical composition, the 'chemical fingerprint', can provide information about trading routes, extension of territory, long-distance contacts and the mobility of prehistoric people. Several museum collections contain large numbers of unidentified obsidian finds. Therefore, a novel scientific approach for provenancing obsidian artefacts found in archaeological contexts is demanded. The establishment of the Obsidian Least Destructive Analysis Provenancing System (OLDAPS) contributes to both conservation and prehistoric research by ensuring a minimum of destruction to gain a maximum of information. Obsidian samples of seven archaeologically relevant geological obsidian sources in Central and Southern Europe were characterized by the application of three different methods: Neutron Activation Analysis (NAA) Ion Beam Analysis (IBA) comprising of Particle Induced X-ray Emission (PIXE) and Particle Induced Gamma-ray Emission (PIGE) Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry (LA-ICP-MS) The reproducibility and accuracy of analytical data is demonstrated by the excellent agreement between determined analytical results and certified values of glassy reference material BAM-S005B. The combination of methods shows a maximum element spectrum composed of 42 elements and reveals the most characteristic -key elements-, in particular Ti, Co, As, Rb, Ba, Eu and U, by which all seven obsidian sources are cleary discriminable. OLDAPS developed the following analytical strategy to provenance archaeological obsidian, which most likely stem from Central or Southern Europe: The application

  15. Handbook on simultaneous x-ray and γ-ray ion beam methods for fine particle analysis

    International Nuclear Information System (INIS)

    Cohen, D.D.

    2000-01-01

    Sampling, measurement, characterisation and source appointment of fine atmospheric particles has become increasingly important in recent times. This is due in part to the realisation that the fine particle pollution caused by anthropogenic activities plays a key role in certain aspects of human health, pollution transport and global climate change. This publication discusses accelerator based ion beam analysis (IBA) methods of particle induced X-ray emission (PIXE) and particle induced γ-ray emission (PIGE) as applied to aerosol analysis. These techniques are sensitive, multielemental, mainly non-destructive, require no sample preparation, have short analysis times and can be used to analyse hundreds of filter samples a day in batch processing with minimum operator interaction. The aspects discussed in the publication include: the basics of the techniques; spectrum analysis; system calibration and blank subtraction; quantification; sensitivity; measurement errors

  16. PIXE and ion beam analysis in forensics

    International Nuclear Information System (INIS)

    Bailey, Melanie; Warmenhoven, John; Chrislopher, Matt; Kirkby, Karen; Palitsin, Vladimir; Grime, Geoff; Jeynes, Chris; Jones, Brian; Wenn, Roger

    2013-01-01

    Full text: University of Surrey has, for the past four years, collaborated with police institutions from across Europe and the rest of the world lo scope potential applications of ion beam analysis (IBA) in forensic science. In doing this we have consulted practitioners across a range of forensic disciplines, and critically compared IBA with conventional characterisation techniques to investigate the areas in which IBA can add evidential value. In this talk, the results of this feasibility study will be presented, showing the types of sample for which IBA shows considerable promise. We will show how a combination of PIXE with other IBA techniques (EBS, PIGE, MeV-SIMS) can be used to give unprecedented characterisation of forensic samples and comment on the significance of these results for forensic casework. We will also show cases where IBA not appear to add any significant improvement over conventional techniques. (author)

  17. The nuclear interaction analysis methods for diagnostics of high power ion beam technologies

    Energy Technology Data Exchange (ETDEWEB)

    Ryzhkov, V A; Grushin, I I; Remnev, G E [Nuclear Physics Inst., Tomsk (Russian Federation)

    1997-12-31

    The complex of Nuclear Interaction Analysis Methods including charged particle activation analysis (CPAA and HIAA), spectrometry of ion induced gamma-emission (PIGE and HIIGE) , characteristic X-ray emission (PIXE), and Rutherford Backscattering Spectrometry (RBS), have been used for diagnostics of the High Power Ion Beam (HPIB) assisted technologies. Accelerated ion beams from the EG-2.5 electrostatic generator and U-120 cyclotron were used for implementation of the techniques. The complex allows a lot of problems of elemental and isotopic analysis to be addressed. First, it is the determination of micro- and macrocomponents of modified materials; second, determination of surface density of thin films, multilayers and coatings, total surface gaseous contamination and amounts of the elements implanted in specimens; third, measurement of concentration depth profiles of the elements. Experiments have shown that the preferable application of nuclear analysis methods allows us to avoid the considerable errors arising when the concentration depth profiles of elements are measured by SIMS or AES in studies of mass transfer processes induced by HPIBs. (author). 1 tab., 2 figs., 3 refs.

  18. Contribution of ion beam analysis methods to the development of 2nd generation high temperature superconducting (HTS) wires

    Energy Technology Data Exchange (ETDEWEB)

    Usov, Igor O [Los Alamos National Laboratory; Arendt, Paul N [Los Alamos National Laboratory; Stan, Liliana [Los Alamos National Laboratory; Holesinger, Terry G [Los Alamos National Laboratory; Foltyn, Steven R [Los Alamos National Laboratory; Depaula, Raymond F [Los Alamos National Laboratory

    2009-01-01

    One of the crucial steps in the second generation high temperature superconducting wire program was development of the buffer layer architecture. The architecture designed at the Superconductivity Technology Center at Los Alamos National Laboratory consists of several oxide layers wherein each layer plays a specific role, namely: nucleation layer, diffusion barrier, biaxially textured template, and an intermediate layer with a good match to the lattice parameter of superconducting Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub 7} (YBCO) compound. This report demonstrates how a wide range of ion beam analysis techniques (SIMS, RBS, channeling, PIXE, PIGE, NRA, ERD) was employed for analysis of each buffer layer and the YBCO films. These results assisted in understanding of a variety of physical processes occurring during the buffet layer fabrication and helped to optimize the buffer layer architecture as a whole.

  19. Optimization of simultaneous electrochemical determination of Cd(II), Pb(II), Cu(II) and Hg(II) at carbon nanotube-modified graphite electrodes.

    Science.gov (United States)

    Pikna, L'ubomír; Heželová, Mária; Kováčová, Zuzana

    2015-01-01

    The health of the environment is worsening every day. Monitoring of potentially toxic elements and remediation of environmental pollution are necessary. Therefore, the research and development of simple, inexpensive, portable and effective sensors is important. Electrochemistry is a useful component of the field of environment monitoring. The present study focuses on evaluating and comparing three types of electrodes (PIGE, PIGE/MWCNT/HNO3 and PIGE/MWCNT/EDTA/HNO3) employed for the simultaneous electrochemical determination of four potentially toxic elements: Cd(II), Pb(II), Cu(II) and Hg(II). Cyclic voltammograms were measured in an acetate buffer. The LOD, LOQ, the standard and relative precisions of the method and a prediction intervals were calculated (according to the technical procedure DIN 32 645) for the three electrodes and for each measured element. The LOD for PIGE/CNT/HNO3 (the electrode with narrowest calculated prediction intervals) was 2.98 × 10(-7) mol L(-1) for Cd(II), 4.83 × 10(-7) mol L(-1) for Pb(II), 3.81 × 10(-7) mol L(-1) for Cu(II), 6.79 × 10(-7) mol L(-1) for Hg(II). One of the benefits of this study was the determination of the amount of Hg(II) in the mixture of other elements.

  20. Activation analysis in Greece

    International Nuclear Information System (INIS)

    Grimanis, A.P.

    1985-01-01

    A review of research and development on NAA as well as examples of applications of this method are presented, taken from work carried out over the last 21 years at the Radioanalytical Laboratory of the Department of Chemistry in the Greek Nuclear Research Center ''Demokritos''. Improved and faster radiochemical NAA methods have been developed for the determination of Au, Ni, Cl, As, Cu, U, Cr, Eu, Hg and Mo in several materials, for the simultaneous determination of Br and I; Mg, Sr and Ni; As and Cu; As, Sb and Hg; Mn, Sr and Ba; Cd and Zn; Se and As; Mo and Cr in biological materials. Instrumental NAA methods have also been developed for the determination of Ag, Cl and Na in lake waters, Al, Ca, Mg and V in wines, 7 trace elements in biological materials, 17 trace elements in sediments and 20 minor and trace elements in ceramics. A comprehensive computer program for routine activation analysis using Ge(Li) detectors have been worked out. A rather extended charged-particle activation analysis program is carried out for the last 10 years, including particle induced X-ray emission (PIXE) analysis, particle induced prompt gamma-ray emission analysis (PIGE), other nuclear reactions and proton activation analysis. A special neutron activation method, the delayed fission neutron counting method is used for the analysis of fissionable elements, as U, Th, Pu, in samples of the whole nuclear fuel cycle including geological, enriched and nuclear safeguards samples

  1. Fluorinated Compounds in US Fast Food Packaging | Science ...

    Science.gov (United States)

    Per- and polyfluoroalkyl substances (PFASs) are highly persistent synthetic chemicals, some of which have been associated with cancer, developmental toxicity, immunotoxicity, and other health effects. PFASs in grease-resistant food packaging can leach into food and increase dietary exposure. We collected ∼400 samples of food contact papers, paperboard containers, and beverage containers from fast food restaurants throughout the United States and measured total fluorine using particle-induced γ-ray emission (PIGE) spectroscopy. PIGE can rapidly and inexpensively measure total fluorine in solid-phase samples. We found that 46% of food contact papers and 20% of paperboard samples contained detectable fluorine (>16 nmol/cm2). Liquid chromatography/high-resolution mass spectrometry analysis of a subset of 20 samples found perfluorocarboxylates, perfluorosulfonates, and other known PFASs and/or unidentified polyfluorinated compounds (based on nontargeted analysis). The total peak area for PFASs was higher in 70% of samples (10 of 14) with a total fluorine level of >200 nmol/cm2 compared to six samples with a total fluorine level of food packaging demonstrates their potentially significant contribution to dietary PFAS exposure and envi

  2. Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

    Science.gov (United States)

    Yasuhiro, Matsuda; Katsushi, Okuyama; Hiroko, Yamamoto; Hisanori, Komatsu; Masashi, Koka; Takahiro, Sato; Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano

    2015-04-01

    To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials ["MS coats F" (MSF)] and fluoride-free sealing materials ("hybrid coats 2" [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8-4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries.

  3. Atomic and Nuclear Analytical Methods XRF, Mössbauer, XPS, NAA and Ion-Beam Spectroscopic Techniques

    CERN Document Server

    Verma, H R

    2007-01-01

    This book is a blend of analytical methods based on the phenomenon of atomic and nuclear physics. It comprises comprehensive presentations about X-ray Fluorescence (XRF), Mössbauer Spectroscopy (MS), X-ray Photoelectron Spectroscopy (XPS), Neutron- Activation Analysis (NAA), Particle Induced X-ray Emission Analysis (PIXE), Rutherford Backscattering Analysis (RBS), Elastic Recoil Detection (ERD), Nuclear Reaction Analysis (NRA), Particle Induced Gamma-ray Emission Analysis (PIGE), and Accelerator Mass Spectrometry (AMS). These techniques are commonly applied in the fields of medicine, biology, environmental studies, archaeology or geology et al. and pursued in major international research laboratories.

  4. Atomic and nuclear analytical methods. XRF, Moessbauer, XPS, NAA and ion-beam spectroscopic techniques

    International Nuclear Information System (INIS)

    Verma, H.R.

    2007-01-01

    This book is a blend of analytical methods based on the phenomenon of atomic and nuclear physics. It comprises comprehensive presentations about X-ray Fluorescence (XRF), Moessbauer Spectroscopy (MS), X-ray Photoelectron Spectroscopy (XPS), Neutron- Activation Analysis (NAA), Particle Induced X-ray Emission Analysis (PIXE), Rutherford Backscattering Analysis (RBS), Elastic Recoil Detection (ERD), Nuclear Reaction Analysis (NRA), Particle Induced Gamma-ray Emission Analysis (PIGE), and Accelerator Mass Spectrometry (AMS). These techniques are commonly applied in the fields of medicine, biology, environmental studies, archaeology or geology et al. and pursued in major international research laboratories. (orig.)

  5. In-situ measurement of the lithium distribution in Li-ion batteries using micro-IBA techniques

    International Nuclear Information System (INIS)

    Yamazaki, A.; Orikasa, Y.; Chen, K.; Uchimoto, Y.; Kamiya, T.; Koka, M.; Satoh, T.; Mima, K.; Kato, Y.; Fujita, K.

    2016-01-01

    Direct observation of lithium concentration distribution in lithium-ion battery composite electrodes has been performed for the first time. Lithium-ion battery model cells for particle induced X-ray emission (PIXE) and particle induced gamma ray emission (PIGE) measurements were designed and fabricated. Two dimensional images of lithium concentration in LiFePO_4 composite electrodes were obtained with PIXE and PIGE by scanning the proton microbeam for various charged states of the electrodes. Lithium concentration in LiFePO_4 composite electrodes was decreased from the contact interface between LiFePO_4 electrode and liquid electrolyte during the charge reaction.

  6. Analysis of garnets from the archaeological sites in Slovenia

    Energy Technology Data Exchange (ETDEWEB)

    Šmit, Ž., E-mail: ziga.smit@fmf.uni-lj.si [Faculty of Mathematics and Physics, University of Ljubljana, Ljubljana (Slovenia); Jožef Stefan Institute, Ljubljana (Slovenia); Fajfar, H. [Jožef Stefan Institute, Ljubljana (Slovenia); Jeršek, M. [Slovenian Museum of National History, Ljubljana (Slovenia); Knific, T. [National Museum of Slovenia, Ljubljana (Slovenia); Lux, J. [Institute for the Protection of Cultural Heritage of Slovenia, Ljubljana (Slovenia)

    2014-06-01

    Garnets (62 individual stones) originating from the Migration Period cemeteries and hilltop settlements in Slovenia were analyzed by the combined PIXE/PIGE method for their chemical composition. Typologically, the analyzed stones may be classified as almandines originating from the sites in India, belonging to types I and II according to Calligaro. A smaller group of pyraldines intermediate between almandines and pyropes was also determined; identified as type III, their source is most likely in Sri Lanka. No garnets from Bohemia (Czech Republic) have been discovered, which may be related to important political changes in the 7th c. AD, induced by Slavic and Avaric migrations.

  7. Chemical characterization of materials relevant to nuclear technology using neutron and proton based nuclear analytical methods

    International Nuclear Information System (INIS)

    Acharya, R.

    2014-01-01

    Nuclear analytical techniques (NATs), utilizing neutron and proton based nuclear reactions and subsequent measurement of gamma rays, are capable of chemical characterization of various materials at major to trace concentration levels. The present article deals with the recent developments and applications of conventional and k0-based internal monostandard (i) neutron activation analysis (NAA) and (ii) prompt gamma ray NAA (PGNAA) methods as well as (iii) in situ current normalized particle induced gamma ray emission (PIGE). The materials that have been analyzed by NAA and PGNAA include (i) nuclear reactor structural materials like zircaloys, stainless steels, Ni alloys, high purity aluminium and graphite and (ii) uranium oxide, U-Th mixed oxides, uranium ores and minerals. Internal monostandard NAA (IM-NAA) method with in situ detection efficiency was used to analyze large and non-standard geometry samples and standard-less compositional characterization was carried out for zircaloys and stainless steels. PIGE methods using proton beams were standardized for quantification of low Z elements (Li to Ti) and applied for compositional analysis of borosilicate glass and lithium titanate (Li 2 TiO 3 ) samples and quantification of total B and its isotopic composition of B ( 10 B/ 11 B) in boron based neutron absorbers like B 4 C. (author)

  8. Investigation of clustering in sets of analytical data

    Energy Technology Data Exchange (ETDEWEB)

    Kajfosz, J [Institute of Nuclear Physics, Cracow (Poland)

    1993-04-01

    Foundation of the statistical method of cluster analysis are briefly presented and its usefulness for the examination and evaluation of analytical data obtained from series of samples investigated by PIXE, PIGE or other methods is discussed. A simple program for fast examination of dissimilarities between samples within an investigated series is described. Useful information on clustering for several hundreds of samples can be obtained with minimal time and storage requirements. (author). 5 refs, 10 figs.

  9. Investigation of clustering in sets of analytical data

    International Nuclear Information System (INIS)

    Kajfosz, J.

    1993-04-01

    Foundation of the statistical method of cluster analysis are briefly presented and its usefulness for the examination and evaluation of analytical data obtained from series of samples investigated by PIXE, PIGE or other methods is discussed. A simple program for fast examination of dissimilarities between samples within an investigated series is described. Useful information on clustering for several hundreds of samples can be obtained with minimal time and storage requirements. (author). 5 refs, 10 figs

  10. Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

    Energy Technology Data Exchange (ETDEWEB)

    Yasuhiro, Matsuda, E-mail: matsuda@den.hokudai.ac.jp [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan); Katsushi, Okuyama [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan); Hiroko, Yamamoto [Graduate School of Dentistry, Osaka University (Japan); Hisanori, Komatsu [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan); Masashi, Koka; Takahiro, Sato [Takasaki Advanced Radiation Research Institute, JAEA (Japan); Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan)

    2015-04-01

    To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials [“MS coats F” (MSF)] and fluoride-free sealing materials (“hybrid coats 2” [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8–4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries.

  11. Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

    International Nuclear Information System (INIS)

    Yasuhiro, Matsuda; Katsushi, Okuyama; Hiroko, Yamamoto; Hisanori, Komatsu; Masashi, Koka; Takahiro, Sato; Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano

    2015-01-01

    To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials [“MS coats F” (MSF)] and fluoride-free sealing materials (“hybrid coats 2” [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8–4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries

  12. In-situ measurement of the lithium distribution in Li-ion batteries using micro-IBA techniques

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, A., E-mail: yamazaki@tac.tsukuba.ac.jp [Faculty of Pure and Applied Sciences, University of Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki 305-8577 (Japan); Orikasa, Y.; Chen, K.; Uchimoto, Y. [Graduate School of Human and Environmental Studies, Kyoto University, Yoshida-nihonmatsucho, Sakyo-ku, Kyoto 606-8501 (Japan); Kamiya, T.; Koka, M.; Satoh, T. [Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA), 1233, Watanuki-machi, Takasaki, Gunma 370-1292 (Japan); Mima, K.; Kato, Y.; Fujita, K. [The Graduate School for the Creation of New Photonics Industries, 1955-1, Kurematsu, NIshi-ku, Hamamatsu, Shizuoka 431-1202 (Japan)

    2016-03-15

    Direct observation of lithium concentration distribution in lithium-ion battery composite electrodes has been performed for the first time. Lithium-ion battery model cells for particle induced X-ray emission (PIXE) and particle induced gamma ray emission (PIGE) measurements were designed and fabricated. Two dimensional images of lithium concentration in LiFePO{sub 4} composite electrodes were obtained with PIXE and PIGE by scanning the proton microbeam for various charged states of the electrodes. Lithium concentration in LiFePO{sub 4} composite electrodes was decreased from the contact interface between LiFePO{sub 4} electrode and liquid electrolyte during the charge reaction.

  13. Study of atmospheric aerosols by IBA techniques: The LABEC experience

    Science.gov (United States)

    Lucarelli, F.; Calzolai, G.; Chiari, M.; Nava, S.; Carraresi, L.

    2018-02-01

    At the 3 MV Tandetron accelerator of the LABEC laboratory of INFN (Florence, Italy) an external beam facility is fully dedicated to PIXE-PIGE measurements of the elemental composition of atmospheric aerosols. All the elements with Z > 10 are simultaneously detected by PIXE typically in one minute. This setup allows us an easy automatic positioning, changing and scanning of samples collected by different kinds of devices: long series of daily PM (Particulate Matter) samples can be analysed in short times, as well as size-segregated and high time-resolution aerosol samples. Thanks to the capability of detecting all the crustal elements, PIXE-PIGE analyses are unrivalled in the study of mineral dust: consequently, they are very effective in the study of natural aerosols, like, for example, Saharan dust intrusions. Among the detectable elements there are also important markers of anthropogenic sources, which allow effective source apportionment studies in polluted urban environments using a multivariate method like Positive Matrix Factorization (PMF). Examples regarding recent monitoring campaigns, performed in urban and remote areas, both daily and with high time resolution (hourly samples), as well as with size selection, are presented. The importance of the combined use of the Particle Induced Gamma Ray emission technique (PIGE) and of other complementary (non-nuclear) techniques is highlighted.

  14. PIXE analysis of sand and soil from Ulaanbaatar and Karakurum, Mongolia

    Science.gov (United States)

    Markwitz, A.; Barry, B.; Shagjjamba, D.

    2008-09-01

    Twenty-one sand and soil samples were collected at the surface from 22 to 25 June 2007 at sampling sites from Ulaanbaatar to Karakurum, Mongolia. The sand samples were collected from constantly changing sand dunes which may still contain salt from prehistoric oceans. The dry sand and soil samples were processed for PIXE and PIGE analyses. A clear division between soils and sand become apparent in the silicon results. Concentrations of all bulk elements in human habitation samples and of Si, Al, K and Fe in dry lake/flood plain samples are similar to those in the soils and sands. Among elements which could be regarded as being at trace concentrations the average S concentration in the soils is 0.9 g kg-1 whereas it is not detected in the sand samples. Zinc and Cu concentrations are both higher in the soils than the sands and are strongly correlated. A surprising presence of uranium at a concentration of 350 mg kg-1 was detected in the PIXE measurement on one of the dry lake samples. Gamma spectrometry confirmed the presence of U in this sample and also at a lower level in a sample from the lake shore, but in none of the other samples. Further, the gamma spectrometry showed that 238U decay products were present only at a level corresponding to about 3 mg kg-1 U for a system in radioactive equilibrium, a figure which is typical for U in the earth's crust. Disequilibria between 238U and its decay products occur naturally but such a high degree of separation at high concentration would be unique if confirmed. PIXE and PIGE measurements of these samples highlight the difficulty in correlating trace element measurements with occurrence of indicators of sea salt in air particulate samples.

  15. Nuclear analytical chemistry: recent developments and applications

    International Nuclear Information System (INIS)

    Acharya, R.

    2013-01-01

    Recent R and D studies on Nuclear Analytical Chemistry utilizing techniques like Neutron Activation Analysis (NAA), Prompt Gamma-ray NAA (PGNAA), Particle Induced Gamma Ray and X-Ray Emission (PICE/PIXE) for compositional analysis of materials have been summarized. The work includes developments and applications of (i) single comparator NAA, called as k 0 -NAA, (ii) k 0 -based internal monostandard NAA (IM-NAA), (iii) k 0 -based prompt gamma ray NAA (PGNAA) and (iv) instrumental NAA using thermal and epithermal neutrons and (v) PIGE and PIXE methods using proton beam for low Z and medium Z elements, respectively. (author)

  16. IBA of iridescent Art Nouveau glass - comparative studies

    International Nuclear Information System (INIS)

    Maeder, M.; Jembrih-Simbuerger, D.; Neelmeijer, C.; Schreiner, Manfred

    2005-01-01

    Simultaneous PIXE, PIGE, and RBS in air were employed to characterise the surface structure of iridescent Art Nouveau glass artefacts produced around 1900 by Tiffany, USA and Loetz, Austria. Using PIXE and PIGE, the chemical composition of the bulk glass and the overlays was determined in a non-destructive manner. Furthermore, the combination of PIXE and RBS enabled the layer structure of the analysed glasses (bulk, overlays, and iridescent layers) and the thicknesses of the thin layers in the near-surface domain to be determined. The measurement and evaluation procedure is demonstrated on blue iridescent glass fragments of Tiffany and Loetz by way of example. The initial results showing similarities but also differences in the layered glass structure of Tiffany and Loetz objects are presented

  17. IBA techniques: Examples of useful combinations for the characterisation of cultural heritage materials

    Science.gov (United States)

    Beck, L.; Pichon, L.; Moignard, B.; Guillou, T.; Walter, P.

    2011-12-01

    For many years, ion beam analysis techniques have successfully been used to the study of cultural heritage objects. The chemical composition of work art is usually determined by PIXE, but in many cases, RBS and/or PIGE can provide useful complementary information. RBS gives information about the depth distribution and concentration in light elements, such as carbon and oxygen. In the past years, the experimental facilities at the AGLAE (Accélérateur Grand Louvre d'Analyse Élémentaire) accelerator has been progressively developed in order to apply simultaneously PIXE, PIGE and RBS under optimal conditions using an external beam. This combination is now routinely used for point analyses or mappings. In this contribution, we present several examples of applications: manufacturing technology of lustre-decorated ceramics and silver plating, control of altered or restored surfaces, and quantification of organic phase in painting and bone. The final conclusion is that the association of PIXE with RBS is very attractive for the investigation of cultural heritage objects, in particular of materials containing both mineral and organic components or possessing a multilayered structure. The first results of the production of monochromatic X-rays for radiography purposes by PIXE are also presented.

  18. IBA techniques: Examples of useful combinations for the characterisation of cultural heritage materials

    International Nuclear Information System (INIS)

    Beck, L.; Pichon, L.; Moignard, B.; Guillou, T.; Walter, P.

    2011-01-01

    For many years, ion beam analysis techniques have successfully been used to the study of cultural heritage objects. The chemical composition of work art is usually determined by PIXE, but in many cases, RBS and/or PIGE can provide useful complementary information. RBS gives information about the depth distribution and concentration in light elements, such as carbon and oxygen. In the past years, the experimental facilities at the AGLAE (Accélérateur Grand Louvre d’Analyse Élémentaire) accelerator has been progressively developed in order to apply simultaneously PIXE, PIGE and RBS under optimal conditions using an external beam. This combination is now routinely used for point analyses or mappings. In this contribution, we present several examples of applications: manufacturing technology of lustre-decorated ceramics and silver plating, control of altered or restored surfaces, and quantification of organic phase in painting and bone. The final conclusion is that the association of PIXE with RBS is very attractive for the investigation of cultural heritage objects, in particular of materials containing both mineral and organic components or possessing a multilayered structure. The first results of the production of monochromatic X-rays for radiography purposes by PIXE are also presented.

  19. Suitable activated carbon-13 tracer techniques

    International Nuclear Information System (INIS)

    Zhang Weicheng; Peng Xiuru; Wang Yuhua

    1995-12-01

    Feasibility and applicability studies of the proton induced gamma ray emission (PIGE) have been performed. The graphite was firstly bombarded at various proton energies to determine gamma ray yield (and, thus, sensitivities) for the reaction of interest. The accuracy for the determination of 13 C abundance was checked, and the precision with which this value and ratios 13 C/ 12 C may be obtained was established by repetitive analysis samples. The performance of different standards in this determination was assessed. The mathematical treatment was developed for the determination of 13 C abundance in tracer studies, and to derive the equations that govern this method of analysis from first principles, to arrive finally at a simple expression by virtue of the observed regularities. The system was calibrated by measuring the gamma ray yield form the 12 C (p, γ) 13 N and 13 C(p,γ) 14 N reaction as a function of known 13 C enrichment. Using this experimentally determined calibration curve, unknown materials can be assayed. This technique is applicable to the analysis of samples with 13 C enrichments between 0.1% and 90%. The samples of human breath natural samples were analyzed against graphite and Cylinder CO 2 standards. Relative standard deviations were 13 C abundance, an increase in 13 C per cent isotopic abundance from the natural 1.11% (average) to only 1.39% may be ascertained. Finally, PIGE is compared with more classical techniques for analysis of 13 C tracer experiments. Ease and speed are important advantages of this technique over mass spectrometry, and its error is compatible with the natural variation of biological results. (9 refs., 11 figs., 9 tabs.)

  20. Nuclear analytical techniques and applications to materials processing

    International Nuclear Information System (INIS)

    Blondiaux, G.; Debrun, J.L.

    1993-01-01

    This paper will present the application of Rutherford backscattering spectrometry to thin film steochiometry determination and application to optimization of the film process elaboration in the case of dielectric films (Ge,Pb,O) and ionic conductors films (Na,Al,O). After we shall present the application of particles induced gamma emission (PIGE) for the characterization of ternary compounds (B,Si,C) used as coating to protect composites materials. The last part of this paper will describe the determination of oxygen in the bulk of fluoride glasses with charged particles activation analysis. (orig.)

  1. A new mapping acquisition and processing system for simultaneous PIXE-RBS analysis with external beam

    International Nuclear Information System (INIS)

    Pichon, L.; Beck, L.; Walter, Ph.; Moignard, B.; Guillou, T.

    2010-01-01

    The combination of ion beam analysis techniques is particularly fruitful for the study of cultural heritage objects. For several years, the AGLAE facility of the Louvre laboratory has been implementing these techniques with an external beam. The recent set-up permits to carry out PIXE, PIGE and RBS simultaneously on the same analyzed spot with a particle beam of approximately 20 μm diameter. A new mapping system has been developed in order to provide elemental concentration maps from the PIXE and RBS spectra. This system combines the Genie2000 spectroscopy software with a homemade software that creates maps by handling acquisition with the object position. Each pixel of each PIXE and RBS maps contains the spectrum normalised by the dose. After analysing each pixel of the PIXE maps (low and high energy X-ray spectra) with the Gupixwin peak-fitting software, quantitative elemental concentrations are obtained for the major and trace elements. This paper presents the quantitative elemental maps extracted from the PIXE spectra and the development of RBS data processing for light element distribution and thin layer characterization. Examples on rock painting and lustrous ceramics will be presented.

  2. On the evaluation of micromatter thin standards by RBS

    International Nuclear Information System (INIS)

    Ionescu, M.; Stelcer, E.; Hawas, O.; Siegele, R.; Cohen, D.; Linch, D.; Sarbutt, A.; Garton, D.

    2005-01-01

    Thin film standards are routinely used in PIXE and PIGE techniques for elemental analysis of particulates present in air samples, collected on Teflon filters. A number of parameters such as thickness, homogeneity and the type and amount of impurities present in the standards are crucial in order to perform high accuracy measurements. In this paper we report the use of RBS on the new STAR 2MV accelerator for characterisation of thin film standards obtained commercially. All standards were produced by MicroMatter Co. on polymer substrates, using a room temperature evaporation method. (author). 4 refs., 5 figs., 1 tab

  3. Li distribution characterization in Li-ion batteries positive electrodes containing LixNi0.8Co0.15Al0.05O2 secondary particles (0.75 ⩽ x ⩽ 1.0)

    International Nuclear Information System (INIS)

    Mima, K.; Gonzalez-Arrabal, R.; Azuma, H.; Yamazaki, A.; Okuda, C.; Ukyo, Y.; Sawada, H.; Fujita, K.; Kato, Y.; Perlado, J.M.; Nakai, S.

    2012-01-01

    The elemental distribution of as-received (non-charged) and charged Li-ion battery positive electrodes containing Li x Ni 0.8 Co 0.15 Al 0.05 O 2 (0.75 ⩽ x ⩽ 1.0) microparticles as active material is characterized by combining μ-PIXE and μ-PIGE techniques. PIGE measurements evidence that the Li distribution is inhomogeneous (existence of Li-rich and Li-depleted regions) in as-received electrodes corresponding with the distribution of secondary particles but it is homogeneous within the studied individual secondary micro-particles. The dependence of the Li distribution on electrode thickness and on charging conditions is characterized by measuring the Li distribution maps in specifically fabricated cross-sectional samples. These data show that decreasing the electrode thickness down to 35 μm and charging the batteries at slow rate give rise to more homogeneous Li depth profiles.

  4. Analysis of early medieval glass beads - Glass in the transition period

    Energy Technology Data Exchange (ETDEWEB)

    Smit, Ziga, E-mail: ziga.smit@ijs.si [Faculty of Mathematics and Physics, University of Ljubljana, Jadranska 19, SI-1000 Ljubljana (Slovenia); Jozef Stefan Institute, Jamova 39, P.O.B. 3000, SI-1001 Ljubljana (Slovenia); Knific, Timotej [National Museum of Slovenia, Presernova 20, SI-1000 Ljubljana (Slovenia); Jezersek, David [Jozef Stefan Institute, Jamova 39, P.O.B. 3000, SI-1001 Ljubljana (Slovenia); Istenic, Janka [National Museum of Slovenia, Presernova 20, SI-1000 Ljubljana (Slovenia)

    2012-05-01

    Glass beads from graves excavated in Slovenia and dated archaeologically to the 7th-10th century AD were analysed by the combined PIXE-PIGE method. The results indicate two groups of glass; natron glass made in the Roman tradition and glass made with alkalis from the ash of halophytic plants, which gradually replaced natron glass after c. 800 AD. The alkalis used in the second group of glass seem to be in close relation to a variant of the Venetian white glass that appeared several centuries later. The origin of this glass may be traced to glass production in Mesopotamia and around the Aral Sea. All the mosaic beads with eye decoration, as well as most of the drawn-segmented and drawn-cut beads analysed, are of plant-ash glass, which confirms their supposed oriental origin.

  5. Provenance studies of obsidians from Neolithic contexts in Southern Italy by IBA (Ion Beam Analysis) methods

    International Nuclear Information System (INIS)

    Quarta, Gianluca; Maruccio, Lucio; Calcagnile, Lucio

    2011-01-01

    Obsidian samples recovered in archaeological contexts in Southern Italy were analysed by PIXE (Particle Induced X-ray Emission) and PIGE (Particle Induced Gamma Ray Emission) for the quantitative determination of both major and trace elements composition. The archaeological contexts were absolutely dated to the 5th millennium BC by mean of AMS (Accelerator Mass Spectrometry) radiocarbon dating analyses carried out on associated organic materials such as charcoal and human bones. The comparison of the compositional results obtained for the analysed samples with published data available for the known obsidian sources in the Mediterranean allowed to identify the sources of the raw material, giving an important contribution to the reconstruction of the ancient trade and exchange routes in Southern Italy prehistory.

  6. Simultaneous quantification of Li, Ti and O in Lithium titanate by particle induced gamma-ray emission using 8 MeV proton beam

    International Nuclear Information System (INIS)

    Chhillar, Sumit; Acharya, R.; Tripathi, R.; Sodaye, S.; Sudarshan, K.; Pujari, P.K.; Rout, P.C.; Mukherjee, S.K.

    2014-01-01

    Simultaneous quantification of Li, Ti and O in lithium titanate (Li 2 TiO 3 ) is difficult by particle induced gamma-ray emission (PIGE) using low energy (∼4 MeV) proton beam. PIGE method using 8 MeV proton beam at BARC-TIFR pelletron facility was standardized for compositional characterization of sol-gel synthesized Li 2 TiO 3 by determining concentrations of Li, Ti and O simultaneously. Thick targets of samples, synthetic samples and standards were prepared in graphite matrix. Beam current variation was normalized by Rutherford Backscattering Spectrometry (RBS) using a thin gold foil. The gamma-rays of 478, 981 and 6129 keV were measured from 7 Li(p, p'γ) 7 Li, 48 Ti(p, p'γ) 48 Ti and 16 O(p, p'γ) 16 O nuclear reactions for quantification of Li, Ti and O, respectively. The method was validated by determining concentrations of Li, TI and O in a synthetic sample. (author)

  7. Implementation of ionoluminescence in the AGLAE scanning external microprobe

    International Nuclear Information System (INIS)

    Pichon, L.; Calligaro, T.; Gonzalez, V.; Lemasson, Q.; Moignard, B.; Pacheco, C.

    2015-01-01

    The scope of this work is to present the implementation of an IBIL imaging system in the scanning external microprobe of the AGLAE facility so as to correlate luminescence and composition maps provided by PIXE, RBS and PIGE. The challenging integration of the optical spectrometer, due to incompatibility of acquisition timings and data formats with the other IBA channels has motivated the development of a specific acquisition system. This article details the IBIL setup and explains the technical solutions retained for the coupling of IBIL with IBA techniques in order to produce fast and large IBIL-IBA maps. The IBIL maps stored in the same format as the PIXE, RBS and PIGE ones can be visualised and compared using the dedicated AGLAEmap program or the PyMCA processing package. An example of such a coupled mapping on Mesoamerican jade is presented to emphasise the interest of performing simultaneously IBA and IBIL large mappings

  8. Elemental and structural studies at the bone-cartilage interface

    International Nuclear Information System (INIS)

    Kaabar, W.; Daar, E.; Bunk, O.; Farquharson, M.J.; Laklouk, A.; Bailey, M.; Jeynes, C.; Gundogdu, O.; Bradley, D.A.

    2011-01-01

    Micro-Proton Induced X-ray Emission (μ-PIXE) and Proton Induced Gamma-ray Emission (PIGE) techniques were employed in the investigation of trace and essential elements distribution in normal and diseased human femoral head sections affected by osteoarthritis (OA). PIGE was exploited in the determination of elements of low atomic number z 15 viz Ca, Z, P and S were determined by PIXE. Accumulations of key elements in the bone and cartilage sections were observed, significant S and Na concentrations being found in the cartilage region particularly in normal tissues. Zn showed enhanced concentrations at the bone-cartilage interface. At a synchrotron facility, small angle X-ray scattering (SAXS) was utilized on a decalcified human femoral head section affected by OA, direct measurements being made of spatial alterations of collagen fibres. The SAXS results showed a slight decrease in the axial periodicity between normal collagen type I and that in diseased tissue in various sites, in contrast with the findings of others.

  9. Nuclear microprobe analysis of serpentine from the mid-Atlantic ridge

    International Nuclear Information System (INIS)

    Orberger, Beate; Metrich, Nicole; Mosbah, Michelle; Mevel, Catherine; Fouquet, Yves

    1999-01-01

    At mid-ocean ridges, ultramafic rocks are serpentinized by interaction with seawater-derived fluids. Elements, dissolved in large quantities in seawater, e.g., Na, K, Cl, Br, Ca and Sr, can be, in small amounts, incorporated as traces into the crystal structure of the various serpentine minerals (Mg 3 Si 2 O 5 (OH) 4 ). These trace elements can be used to track the composition of the reacting fluids and to constrain physico-chemical conditions. This paper represents the first application of particle-induced X- and γ-ray emission (PIXE/PIGE) analysis to serpentine using the nuclear microprobe at the Laboratoire Pierre Suee (CEA-CNRS). Three types of serpentine, belonging to two different serpentinization generations, have been analysed in samples collected from the Mid-Atlantic Ridge (14 deg. 45'N/45 deg. W) that exposes serpentinized peridotites on which the Logachev black smoker is placed. The trace elements Cl, F, S, Cu, Zn, Ca, K, Ni, Cr and Mn were detected from several tens to several thousands of ppm. Bromine, As and Sr are close to the detection limit of about 5 ppm. The trace element concentrations and interelement relationships in serpentines vary (a) with the serpentine type and (b) with the geographic location to the black smoker. Chlorine and in part S originated from seawater, whereas Cu, Zn, Ca, K, Ni, Cr and Fe and the major amount of S were mobilized from the unaltered host rock and partitioned between the serpentine and the aqueous solution

  10. Ion beam studies of archaeological gold jewellery items

    International Nuclear Information System (INIS)

    Demortier, G.

    1996-01-01

    Analytical work on material of archaeological interest performed at LARN mainly concerns gold jewellery, with an emphasis to solders on the artefacts and to gold plating or copper depletion gilding. PIXE, RBS but also PIGE and NRA have been applied to a large variety of items. On the basis of elemental analysis, we have identified typical workmanship of ancient goldsmiths in various regions of the world: finely decorated Mesopotamian items, Hellenistic and Byzantine craftsmanship, cloisonne of the Merovingian period, depletion gilding on Pre-Colombian tumbaga. This paper is some shortening of the work performed at LARN during the last ten years. Criteria to properly use PIXE for quantitative analysis of non-homogeneous ancient artefacts presented at the 12th IBA conference in 1995 are also shortly discussed. (orig.)

  11. Ion beam studies of archaeological gold jewellery items

    Energy Technology Data Exchange (ETDEWEB)

    Demortier, G [Facultes Universitaires Notre-Dame de la Paix, Namur (Belgium). Lab. d` Analyses par Reactions Nucleaires

    1996-06-01

    Analytical work on material of archaeological interest performed at LARN mainly concerns gold jewellery, with an emphasis to solders on the artefacts and to gold plating or copper depletion gilding. PIXE, RBS but also PIGE and NRA have been applied to a large variety of items. On the basis of elemental analysis, we have identified typical workmanship of ancient goldsmiths in various regions of the world: finely decorated Mesopotamian items, Hellenistic and Byzantine craftsmanship, cloisonne of the Merovingian period, depletion gilding on Pre-Colombian tumbaga. This paper is some shortening of the work performed at LARN during the last ten years. Criteria to properly use PIXE for quantitative analysis of non-homogeneous ancient artefacts presented at the 12th IBA conference in 1995 are also shortly discussed. (orig.).

  12. Volumetric error modeling, identification and compensation based on screw theory for a large multi-axis propeller-measuring machine

    Science.gov (United States)

    Zhong, Xuemin; Liu, Hongqi; Mao, Xinyong; Li, Bin; He, Songping; Peng, Fangyu

    2018-05-01

    Large multi-axis propeller-measuring machines have two types of geometric error, position-independent geometric errors (PIGEs) and position-dependent geometric errors (PDGEs), which both have significant effects on the volumetric error of the measuring tool relative to the worktable. This paper focuses on modeling, identifying and compensating for the volumetric error of the measuring machine. A volumetric error model in the base coordinate system is established based on screw theory considering all the geometric errors. In order to fully identify all the geometric error parameters, a new method for systematic measurement and identification is proposed. All the PIGEs of adjacent axes and the six PDGEs of the linear axes are identified with a laser tracker using the proposed model. Finally, a volumetric error compensation strategy is presented and an inverse kinematic solution for compensation is proposed. The final measuring and compensation experiments have further verified the efficiency and effectiveness of the measuring and identification method, indicating that the method can be used in volumetric error compensation for large machine tools.

  13. Elemental and structural studies at the bone-cartilage interface

    Energy Technology Data Exchange (ETDEWEB)

    Kaabar, W., E-mail: w.kaabar@surrey.ac.uk [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Daar, E. [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Bunk, O. [Swiss Light Source, Paul Scherrer Institute, 5232 Villigen (Switzerland); Farquharson, M.J. [Department of Medical Physics and Applied Radiation Sciences, McMaster University, 1280 Main Street West, Hamilton, Ontario, L8S 4K1 (Canada); Laklouk, A. [Al-Fateh University, Tripoli (Libya); Bailey, M.; Jeynes, C. [Surrey Ion Beam Centre, University of Surrey, Guildford GU2 7XH (United Kingdom); Gundogdu, O. [Umuttepe Campus, University of Kocaeli, 41380 Kocaeli (Turkey); Bradley, D.A. [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom)

    2011-10-01

    Micro-Proton Induced X-ray Emission ({mu}-PIXE) and Proton Induced Gamma-ray Emission (PIGE) techniques were employed in the investigation of trace and essential elements distribution in normal and diseased human femoral head sections affected by osteoarthritis (OA). PIGE was exploited in the determination of elements of low atomic number z<15 such as Na and F whereas elements with z>15 viz Ca, Z, P and S were determined by PIXE. Accumulations of key elements in the bone and cartilage sections were observed, significant S and Na concentrations being found in the cartilage region particularly in normal tissues. Zn showed enhanced concentrations at the bone-cartilage interface. At a synchrotron facility, small angle X-ray scattering (SAXS) was utilized on a decalcified human femoral head section affected by OA, direct measurements being made of spatial alterations of collagen fibres. The SAXS results showed a slight decrease in the axial periodicity between normal collagen type I and that in diseased tissue in various sites, in contrast with the findings of others.

  14. Fluorine profiling after application of various anti-caries gels

    International Nuclear Information System (INIS)

    Zschau, H.E.; Plier, F.; Otto, G.; Wyrwich, C.; Treide, A.

    1990-01-01

    Two newly developed caries-preventing gels were tested together with Elmex on pre-school children over a time of 3 years. Proton-induced gamma-ray emission spectrometry (PIGE) was used to measure the fluorine profiles in milk teeth (incisors). In accordance with the clinical statement the results allow to produce a new anti-caries drug. (orig.)

  15. Examination, characterisation and analysis techniques for the knowledge and the conservation / restoration of cultural heritage - importance of ionising radiation techniques

    International Nuclear Information System (INIS)

    Boutaine; J. L.

    2004-01-01

    For the examination, characterisation and analysis of cultural heritage artefacts or art objects and their component materials, the conservation scientist needs a palette of non destructive and non invasive techniques, in order to improve our knowledge concerning their elaboration, their evolution and/or degradation during time, and to give rational basis for their restoration and conservation. A general survey and illustrations showing the usefulness of these techniques will be presented. Among these methods, many are based on the use of ionising radiation. 1. Radiography (using X-rays, gamma rays, beta particles, secondary electrons, neutrons), electron emission radiography, tomodensimetry, 2. Scanning electron microscope associated with X-ray spectrometry, 3. X-ray diffraction, 4. Synchrotron radiation characterisation, 5. X-ray fluorescence analysis, 6. Activation analysis, 7. Ion beam analysis (PIXE, PIGE, RBS, secondary X-ray fluorescence), 8. Thermoluminescence dating, 9. Carbon-14 dating. These methods are used alone or in connection with other analytical methods. Any kind of materials can be encountered, for instance: i. stones, gems, ceramics, terracotta, enamels, glasses, i i. wood, paper, textile, bone, ivory, i i i. metals, jewellery, i v. paint layers, canvas and wooden backings, pigments, dyers, oils, binding media, varnishes, glues. Some examples will be taken, among recent work done at the Centre of Research and Restoration of the Museums of France (C2RMF), from various geographical origins, various ages and different art disciplines. This will illustrate the kind of assistance that science and technology can provide to a better knowledge of mankind's cultural heritage and also to the establishment of rational basis for its better conservation for the future generations. (Author)

  16. Nuclear microprobe analysis of serpentine from the mid-Atlantic ridge

    Energy Technology Data Exchange (ETDEWEB)

    Orberger, Beate E-mail: orberger@geol.u-psud.fr; Metrich, Nicole; Mosbah, Michelle E-mail: mosbah@drecam.cea.fr; Mevel, Catherine; Fouquet, Yves

    1999-09-02

    At mid-ocean ridges, ultramafic rocks are serpentinized by interaction with seawater-derived fluids. Elements, dissolved in large quantities in seawater, e.g., Na, K, Cl, Br, Ca and Sr, can be, in small amounts, incorporated as traces into the crystal structure of the various serpentine minerals (Mg{sub 3}Si{sub 2}O{sub 5}(OH){sub 4}). These trace elements can be used to track the composition of the reacting fluids and to constrain physico-chemical conditions. This paper represents the first application of particle-induced X- and {gamma}-ray emission (PIXE/PIGE) analysis to serpentine using the nuclear microprobe at the Laboratoire Pierre Suee (CEA-CNRS). Three types of serpentine, belonging to two different serpentinization generations, have been analysed in samples collected from the Mid-Atlantic Ridge (14 deg. 45'N/45 deg. W) that exposes serpentinized peridotites on which the Logachev black smoker is placed. The trace elements Cl, F, S, Cu, Zn, Ca, K, Ni, Cr and Mn were detected from several tens to several thousands of ppm. Bromine, As and Sr are close to the detection limit of about 5 ppm. The trace element concentrations and interelement relationships in serpentines vary (a) with the serpentine type and (b) with the geographic location to the black smoker. Chlorine and in part S originated from seawater, whereas Cu, Zn, Ca, K, Ni, Cr and Fe and the major amount of S were mobilized from the unaltered host rock and partitioned between the serpentine and the aqueous solution.

  17. Fluorine uptake into human enamel around fluoride-containing dental materials during cariogenic pH cycling

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan)], E-mail: kom@den.hokudai.ac.jp; Yamamoto, H. [Graduate School of Dentistry, Osaka University, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Nomachi, M. [Graduate School of Science, Osaka University, 1-1 Machikaneyama, Toyonaka 560-0043 (Japan); Yasuda, K. [The Wakasa wan Energy Research Center, 64-52-1 Hase, Tsuruga 914-0192 (Japan); Matsuda, Y.; Kinugawa, M.; Kijimura, T.; Sano, H. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Satou, T.; Oikawa, S.; Kamiya, T. [Advanced Radiation Technology, TARRI, JAEA, 1233 Watanuki-machi, Takasaki 370-1292 (Japan)

    2009-06-15

    Using PIGE (Proton Induced Gamma Emission) technique at TARRI (Takasaki Advanced Radiation Research Institute), Japan, we measured fluorine (F) uptake into the tooth enamel around two fluoride-containing materials during caries progression using pH cycling. Class V cavities in extracted human teeth were drilled and filled with fluoride-containing materials (i.e. 'Fuji IX' (FN) and 'UniFil flow with MEGA bond' (UF)) and a non-fluoride-containing material (i.e. 'SOLARE with MEGA bond' (SO)). Three 120 {mu}m longitudinal sections including the filling material were obtained from each tooth. In order to simulate daily acid attack occurring in the oral cavity, the pH cycling (pH 6.8-4.5) was carried out for 1, 3 and 5 weeks, separately. After pH cycling, the caries progression in all specimens was observed using transverse microradiography (TMR). The F and calcium distributions of the specimens were evaluated using PIGE and PIXE techniques. The F distribution of the specimens clearly showed the F uptake from FN into enamel adjacent to the filling material, while the F uptakes from UF and SO were not detected. For UF, the MEGA bond (non-fluoride-containing) between the tooth and UniFil flow interfered with the F absorption into the tooth. For FN, the amount of F uptake into the subsurface enamel increased during pH cycling. The amount of F uptake in 5-week pH cycling had significantly higher value compared to those in 1- and 3-week pH cycling. For UF and SO, there were no significant differences between the different durations of pH cycling. Among fluoride-containing materials, there were some differences in the F uptake with increased pH cycling, which could possibly lead to obtaining difference in clinical performance. The data obtained using PIGE and PIXE techniques were useful in understanding the benefit of fluorine by means of fluoride-containing material for preventing caries.

  18. Fluorine uptake into human enamel around fluoride-containing dental materials during cariogenic pH cycling

    International Nuclear Information System (INIS)

    Komatsu, H.; Yamamoto, H.; Nomachi, M.; Yasuda, K.; Matsuda, Y.; Kinugawa, M.; Kijimura, T.; Sano, H.; Satou, T.; Oikawa, S.; Kamiya, T.

    2009-01-01

    Using PIGE (Proton Induced Gamma Emission) technique at TARRI (Takasaki Advanced Radiation Research Institute), Japan, we measured fluorine (F) uptake into the tooth enamel around two fluoride-containing materials during caries progression using pH cycling. Class V cavities in extracted human teeth were drilled and filled with fluoride-containing materials (i.e. 'Fuji IX' (FN) and 'UniFil flow with MEGA bond' (UF)) and a non-fluoride-containing material (i.e. 'SOLARE with MEGA bond' (SO)). Three 120 μm longitudinal sections including the filling material were obtained from each tooth. In order to simulate daily acid attack occurring in the oral cavity, the pH cycling (pH 6.8-4.5) was carried out for 1, 3 and 5 weeks, separately. After pH cycling, the caries progression in all specimens was observed using transverse microradiography (TMR). The F and calcium distributions of the specimens were evaluated using PIGE and PIXE techniques. The F distribution of the specimens clearly showed the F uptake from FN into enamel adjacent to the filling material, while the F uptakes from UF and SO were not detected. For UF, the MEGA bond (non-fluoride-containing) between the tooth and UniFil flow interfered with the F absorption into the tooth. For FN, the amount of F uptake into the subsurface enamel increased during pH cycling. The amount of F uptake in 5-week pH cycling had significantly higher value compared to those in 1- and 3-week pH cycling. For UF and SO, there were no significant differences between the different durations of pH cycling. Among fluoride-containing materials, there were some differences in the F uptake with increased pH cycling, which could possibly lead to obtaining difference in clinical performance. The data obtained using PIGE and PIXE techniques were useful in understanding the benefit of fluorine by means of fluoride-containing material for preventing caries.

  19. Fluorine uptake into human enamel around a fluoride-containing dental material during cariogenic pH cycling

    International Nuclear Information System (INIS)

    Komatsu, H.; Yamamoto, H.; Nomachi, M.; Yasuda, K.; Matsuda, Y.; Murata, Y.; Kijimura, T.; Sano, H.; Sakai, T.; Kamiya, T.

    2007-01-01

    Using PIGE (TIARA, JAPAN) technique, we measured fluorine (F) uptake into the tooth enamel around a fluoride-containing material during caries progression using pH cycling. Class I cavities in the buccal surfaces of 6 extracted human teeth were drilled and filled with fluoride-containing material; a glass ionomer cement (Fuji IX(GC)). Three 300 μm sections through the material were obtained from each tooth. Two of these specimens were utilized to measure the F distribution in enamel adjacent to the material. A 1.7 MeV proton beam accelerated by the TIARA single-ended accelerator was delivered to a micro-beam apparatus. The beam spot size was about 1 μm with a beam current of about 100 pA. A nuclear reaction, 19 F(p, αγ) 16 0, was used to measure the F concentration and the gamma-rays from this reaction were detected with a 4' NaI detector. X-rays induced by proton were detected with a Si(Li) detector to measure calcium concentration and the beam intensity was monitored with the X-ray yield from a copper foil for quantitative analysis. After measurement of F uptake, all specimens were polished to a thickness of 120 μm. In order to simulate daily acid challenges occurring in the oral cavity, the pH cycling (pH6.8-pH4.5) was carried out for 1, 3 and 5 weeks, separately. The duration that the solution remained below pH 5.5 was 37 min per cycle. The cycles were repeated 6 times per day with 2 h interval between cycles, and the specimens were kept in remineralizing solution for the rest of pH cycle. After pH cycling, F and calcium distribution of each specimen was evaluated using PIGE technique. The F distribution of the specimens before pH cycling clearly showed the F uptake from fluoride-containing material into enamel adjacent to the material. After pH cycling, the caries progression in all specimens was observed by the image of transverse microradiography (TMR). The depth of caries and mineral loss progressed with increasing the duration of pH cycling, although

  20. Fluorine uptake into human enamel around a fluoride-containing dental material during cariogenic pH cycling

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan)]. E-mail: kom@den.hokudai.ac.jp; Yamamoto, H. [Graduate School of Dentistry, Osaka University, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Nomachi, M. [Graduate School of Science, Osaka University, 1-1 Machikaneyama, Toyonaka 560-0043 (Japan); Yasuda, K. [Wakasa wan Energy Research Center, 64-52-1 Hase, Tsuruga 914-0192 (Japan); Matsuda, Y. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Murata, Y. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Kijimura, T. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Sano, H. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Sakai, T. [Takasaki Advanced Radiation Research Institute, JAEA, 1233 Watanuki-machi, Takasaki 370-1292 (Japan); Kamiya, T. [Takasaki Advanced Radiation Research Institute, JAEA, 1233 Watanuki-machi, Takasaki 370-1292 (Japan)

    2007-07-15

    Using PIGE (TIARA, JAPAN) technique, we measured fluorine (F) uptake into the tooth enamel around a fluoride-containing material during caries progression using pH cycling. Class I cavities in the buccal surfaces of 6 extracted human teeth were drilled and filled with fluoride-containing material; a glass ionomer cement (Fuji IX(GC)). Three 300 {mu}m sections through the material were obtained from each tooth. Two of these specimens were utilized to measure the F distribution in enamel adjacent to the material. A 1.7 MeV proton beam accelerated by the TIARA single-ended accelerator was delivered to a micro-beam apparatus. The beam spot size was about 1 {mu}m with a beam current of about 100 pA. A nuclear reaction, {sup 19}F(p, {alpha}{gamma}){sup 16}0, was used to measure the F concentration and the gamma-rays from this reaction were detected with a 4' NaI detector. X-rays induced by proton were detected with a Si(Li) detector to measure calcium concentration and the beam intensity was monitored with the X-ray yield from a copper foil for quantitative analysis. After measurement of F uptake, all specimens were polished to a thickness of 120 {mu}m. In order to simulate daily acid challenges occurring in the oral cavity, the pH cycling (pH6.8-pH4.5) was carried out for 1, 3 and 5 weeks, separately. The duration that the solution remained below pH 5.5 was 37 min per cycle. The cycles were repeated 6 times per day with 2 h interval between cycles, and the specimens were kept in remineralizing solution for the rest of pH cycle. After pH cycling, F and calcium distribution of each specimen was evaluated using PIGE technique. The F distribution of the specimens before pH cycling clearly showed the F uptake from fluoride-containing material into enamel adjacent to the material. After pH cycling, the caries progression in all specimens was observed by the image of transverse microradiography (TMR). The depth of caries and mineral loss progressed with increasing the

  1. Nondestructive assay of fluorine in geological and other materials by instrumental photon activation analysis with a microtron

    Energy Technology Data Exchange (ETDEWEB)

    Krausová, Ivana [Nuclear Physics Institute, Academy of Sciences of the Czech Republic, Řež 130, 25068 Řež (Czech Republic); Mizera, Jiří, E-mail: mizera@ujf.cas.cz [Nuclear Physics Institute, Academy of Sciences of the Czech Republic, Řež 130, 25068 Řež (Czech Republic); Institute of Rock Structure and Mechanics, Academy of Sciences of the Czech Republic, V Holešovičkách 41, 182 09 Praha 8 (Czech Republic); Řanda, Zdeněk; Chvátil, David; Krist, Pavel [Nuclear Physics Institute, Academy of Sciences of the Czech Republic, Řež 130, 25068 Řež (Czech Republic)

    2015-01-01

    Reliable determination of low concentrations of fluorine in geological and coal samples is difficult. It usually requires tedious decomposition and dissolution of the sample followed by chemical conversion of fluorine into its anionic form. The present paper examines possibilities of non-destructive determination of fluorine, mainly in minerals, rocks and coal, by instrumental photon activation analysis (IPAA) using the MT-25 microtron. The fluorine assay consists of counting the positron–electron annihilation line of {sup 18}F at 511 keV, which is a product of the photonuclear reaction {sup 19}F(γ, n){sup 18}F and a pure positron emitter. The assay is complicated by the simultaneous formation of other positron emitters. The main contributors to interference in geological samples are from {sup 45}Ti and {sup 34m}Cl, whereas those from {sup 44}Sc and {sup 89}Zr are minor. Optimizing beam energy and irradiation-decay-counting times, together with using interfering element calibration standards, allowed reliable IPAA determination of fluorine in selected USGS and CRPG geochemical reference materials, NIST coal reference materials, and NIST RM 8414 Bovine Muscle. In agreement with the published data obtained by PIGE, the results of the F assay by IPAA have revealed erroneous reference values provided for the NIST reference materials SRM 1632 Bituminous Coal and RM 8414 Bovine Muscle. The detection limits in rock and coal samples are in the range of 10–100 μg g{sup −1}.

  2. Analysis of archaeological precious stones from Slovenia

    Energy Technology Data Exchange (ETDEWEB)

    Šmit, Ž. [Facully of Mathematics and Physics, University of Ljubljana (Slovenia); Fajfar, H. [Jožef Stefan Institute, Ljubljana (Slovenia); Jeršsek, M. [Slovenian Museum of Natural History, Ljubljana (Slovenia); Knific, T. [National Museum of Slovenia, Ljubljana (Slovenia); Kržic, A. [Higher Vocational Centre, Sezana (Slovenia); Lux, J. [Institute for the Protection of Cultural Heritage of Slovenia, Ljubljana (Slovenia)

    2013-07-01

    Full text: Precious stones have been attractive pieces of jewelry since ancient times. However, due to the limited sources of origin, the quality of applied items mainly depended on long-range commercial relations, but also on fashion. In Antiquity and Late Antiquity, stones much used and sought for were emeralds and garnets. In Slovenia, emeralds are typically related to the early Roman period and are incorporated in the finds of gold jewelry from the graves. Emerald is generally beryl colored by admixture of chromium, though green colors can also be due to admixtures of iron or vanadium. Garnets were increasingly used by various nations of the People Migration period, and mounted in gilded silver or gold objects by 'cloisonne' or 'en cabochon' techniques. In Slovenia, numerous jewelry items containing garnets were found in the graves and in post-Roman fortified settlements. Geologically, according to the admixtures of metal ions, the garnets are divided into several species, while the most common among archaeological finds are almandines and pyropes and their intermediate types. It is also common to divide garnets into five groups, the first two originating from India, the third from Ceylon and the fifth from Czech Republic. The measurements involved presumed emeralds from Roman jewelry finds in Slovenia and comparative samples of beryl from Siberia and Habachtal in Austria. The analysis determined the coloring ions and showed relations between particular stones. For garnets, ten samples from brooches, earrings and rings were selected for the analysis on the basis of previous micro Raman examination. The analysis was performed by a combined PIXE-PIGE technique using proton beam in air. The light elements of Na, Mg, AI were determined according to the emitted gamma rays, while X-rays were used for the elements heavier than silicon. Two X-ray spectra were measured in each measuring point, soft and hard X-ray; the latter was obtained using an

  3. Analysis of archaeological precious stones from Slovenia

    International Nuclear Information System (INIS)

    Šmit, Ž.; Fajfar, H.; Jeršsek, M.; Knific, T.; Kržic, A.; Lux, J.

    2013-01-01

    Full text: Precious stones have been attractive pieces of jewelry since ancient times. However, due to the limited sources of origin, the quality of applied items mainly depended on long-range commercial relations, but also on fashion. In Antiquity and Late Antiquity, stones much used and sought for were emeralds and garnets. In Slovenia, emeralds are typically related to the early Roman period and are incorporated in the finds of gold jewelry from the graves. Emerald is generally beryl colored by admixture of chromium, though green colors can also be due to admixtures of iron or vanadium. Garnets were increasingly used by various nations of the People Migration period, and mounted in gilded silver or gold objects by 'cloisonne' or 'en cabochon' techniques. In Slovenia, numerous jewelry items containing garnets were found in the graves and in post-Roman fortified settlements. Geologically, according to the admixtures of metal ions, the garnets are divided into several species, while the most common among archaeological finds are almandines and pyropes and their intermediate types. It is also common to divide garnets into five groups, the first two originating from India, the third from Ceylon and the fifth from Czech Republic. The measurements involved presumed emeralds from Roman jewelry finds in Slovenia and comparative samples of beryl from Siberia and Habachtal in Austria. The analysis determined the coloring ions and showed relations between particular stones. For garnets, ten samples from brooches, earrings and rings were selected for the analysis on the basis of previous micro Raman examination. The analysis was performed by a combined PIXE-PIGE technique using proton beam in air. The light elements of Na, Mg, AI were determined according to the emitted gamma rays, while X-rays were used for the elements heavier than silicon. Two X-ray spectra were measured in each measuring point, soft and hard X-ray; the latter was obtained using an

  4. Elemental composition of urban aerosol collected in Florence, Italy

    International Nuclear Information System (INIS)

    Lucarelli, F.; Mando, P.A.; Nava, S.; Prati, P.; Zucchiatti, A.

    2000-01-01

    An extensive investigation is in progress aiming at the characterisation of the air particulate composition in Florence. The aim is to determine the aerosol elemental concentrations as well to identify pollution sources. For our investigation, we use the external PIXE-PIGE beam facility of the Van de Graaff accelerator of INFN at the Physics Department of the Florence University. We report here an overview of the results of the PIXE analysis of a long temporal series (about 1 yr) of PM 10 particulate collected on Millipore filters on a daily basis in three different sites (characterised by different urban settings). Daily concentrations of more than 20 elements have been obtained. From the observed elemental concentrations seasonal variation were found. A relevant decrease of S, Pb and Br levels has been found with respect to 10 yr ago. Four main sources (traffic, sulphates, soil-dust and wind-transported sea-salt) have been extracted with the help of factor analysis

  5. Depth profiling of {sup 14} N and {sup 20} Ne implantation into iron and steel using(p, gamma) reactions. Vol. 2

    Energy Technology Data Exchange (ETDEWEB)

    Wriekat, A; Haj-Abdellah, M [Physics Department, University of Jordan, Amman (Jordan)

    1996-03-01

    Depth profiles of {sup 14} N and {sup 20} Ne ions at 800 KeV implanted into iron and by steel samples have been measured by means of the proton induced {gamma}- ray emission (Pige) technique. The range, R, and range straggling, {Delta}R for these profiles were obtained and compared with theoretical calculations. The experimental results did show that pure iron retains more N and Ne than steel. 2 figs., 1 tab.

  6. A particle accelerator probes artifacts

    CERN Document Server

    Dran, J C; Salomon, J

    2002-01-01

    The AGLAE system is made up of a 2 mega volts electrostatic accelerator and of 3 irradiation lines: one leads to a vacuum enclosure in which targets are irradiated and the 2 others lines are designed to irradiate targets under an air or helium atmosphere. The AGLAE system is located in the premises of the Louvre museum in Paris and is devoted to the study of cultural objects through ion beam analysis (IBA). 4 techniques are used: -) proton-induced X-ray emission (PIXE) -) proton-induced gamma ray (PIGE) -) Rutherford backscattering spectrometry (NRS) and -) nuclear reaction analysis (NRA). A decisive progress has permitted the direct analysis of artifacts without sampling. The object itself is set just a few millimeters away from the exit window of the beam in an air or helium atmosphere. The exit window must be resistant enough to bear the atmospheric pressure and the damages caused by the proton beam but must be thin enough to not deteriorate the quality of the beam. By using a 10 sup - sup 7 m thick exit w...

  7. Pige klik varsomt, thi scenen er skrå

    DEFF Research Database (Denmark)

    Sandvik, Kjetil

    2007-01-01

    karakter-skabeloner, og i 'massive multiplayer online role-playing games' (MMORPGs) er denne mulighed for at skabe sin egen rolle blandet med mulighederne for dramatisk improvisation med andre spilkarakterer inde i spilverdenen såvel som mulighederne for at 'chatte' med andre spillere som en integreret del...... af selve spiloplevelsen. Dette gameplay skaber en meget kompleks form for rollespil. Ved at anvende Ultima Online som eksempel, ser denne artikel nærmere på den form for rollespil såvel som kompleks dramaturgi som vi finder i MMORPGs og de forskellige niveauer som spilleren udfører sine handlinger på....

  8. Pyomyositis uden feber hos 12-årig pige

    DEFF Research Database (Denmark)

    Maagaard, Mathilde; Hindsø, Klaus; Wislander, Steen Bo

    2009-01-01

    resonance imaging (MRI) revealed infection in the left m. ileopsoas. Previous ultrasound, computerised tomography, x-ray and bone-scintigraphy were normal. After 11 days of intravenous antibiotic therapy and clinical remission, secondary bone affection was detected by a new MRI. Long-term antibiotic...... treatment is required in such cases because of the risk of secondary bone affection. This patient was treated for 11 days with intravenous antibiotic therapy and for the subsequent three months with tablets. Udgivelsesdato: 2009-Mar-2...

  9. Quantitative investigation of physical factors contributing to gold nanoparticle-mediated proton dose enhancement

    International Nuclear Information System (INIS)

    Cho, Jongmin; Manohar, Nivedh; Kerr, Matthew; Cho, Sang Hyun; Gonzalez-Lepera, Carlos; Krishnan, Sunil

    2016-01-01

    Some investigators have shown tumor cell killing enhancement in vitro and tumor regression in mice associated with the loading of gold nanoparticles (GNPs) before proton treatments. Several Monte Carlo (MC) investigations have also demonstrated GNP-mediated proton dose enhancement. However, further studies need to be done to quantify the individual physical factors that contribute to the dose enhancement or cell-kill enhancement (or radiosensitization). Thus, the current study investigated the contributions of particle-induced x-ray emission (PIXE), particle-induced gamma-ray emission (PIGE), Auger and secondary electrons, and activation products towards the total dose enhancement. Specifically, GNP-mediated dose enhancement was measured using strips of radiochromic film that were inserted into vials of cylindrical GNPs, i.e. gold nanorods (GNRs), dispersed in a saline solution (0.3 mg of GNRs/g or 0.03% of GNRs by weight), as well as vials containing water only, before proton irradiation. MC simulations were also performed with the tool for particle simulation code using the film measurement setup. Additionally, a high-purity germanium detector system was used to measure the photon spectrum originating from activation products created from the interaction of protons and spherical GNPs present in a saline solution (20 mg of GNPs/g or 2% of GNPs by weight). The dose enhancement due to PIXE/PIGE recorded on the films in the GNR-loaded saline solution was less than the experimental uncertainty of the film dosimetry (<2%). MC simulations showed highly localized dose enhancement (up to a factor 17) in the immediate vicinity (<100 nm) of GNRs, compared with hypothetical water nanorods (WNRs), mostly due to GNR-originated Auger/secondary electrons; however, the average dose enhancement over the entire GNR-loaded vial was found to be minimal (0.1%). The dose enhancement due to the activation products from GNPs was minimal (<0.1%) as well. In conclusion, under the

  10. Ion-beam analysis of a medieval glass bottle excavated in Gyoer

    International Nuclear Information System (INIS)

    Uzonyi, I.; Szoboszlai, Z.; Kertesz, Zs.; Simon, A.; Kiss, A.Z.

    2008-01-01

    ) techniques: the particle induced X-ray emission (PIXE) and the particle induced gamma ray emission (PIGE) were used. Measurements were carried out on a small glass piece from the present archaeological find which was not used for the restoration. PIXE analysis was carried out at the Scanning Nuclear Microprobe facility. The sample was irradiated at five different spots by 2 MeV H + beam focused to 2x2 μm 2 spot size and applying scan size of 2x2 mm 2 . The accumulated charge at the sample was ∼0.2 μC. Characteristic X-rays were detected by an ultra thin windowed and a Be windowed Si(Li) detectors, thus elements could be analyzed for the Z≥6 atomic number region with high sensitivity. Characteristic X-ray spectra were evaluated with the PIXEKLM-TPI software package. Efficiency calibration of detectors was based on the NIST 610 glass standard reference material. In the case of the PIGE analysis the samples were irradiated in an isolated vacuum chamber with a 3.8 MeV proton beam of about 5 nA. The accumulated charge at the sample was ∼3 μC. The gamma-rays were detected with a 40 % HPGe detector situated at 90 deg with respect to the beam direction and 20 cm distance from the sample. To calculate the concentrations of Na, Al and Si the same NIST 610 glass standard was used. The analysis revealed that the bottle was made from soda-lime glass. Comparing Na, Mg and Ca values with available literature data, 'similarity' with Venice glass can be stated. However, considering the high Ti, Fe (and Al) concentrations it can be supposed that a relatively low quality vitrifying agent (siliceous material) was used excluding late medieval (15-16th c.) fine Venetian glass. The greenish tint attributable to the high Fe content indicates incomplete decolourization (by MnO) which is also characteristic for lower quality glass products. Therefore, the analytical results does not falsify the hypotheses that the artefact can be a 13th century (supposedly Venice) glass

  11. Clearcellekarcinom i livmoderhalsen hos en 17-årig pige

    DEFF Research Database (Denmark)

    Rønneberg, Elisabeth Thal; Lidang, Marianne; Palle, Connie

    2014-01-01

    Clear cell adenocarcinoma of the uterine cervix (CCEA) is a rare disease, accounting for only 1% of all cervical cancers. The disease in young women is linked to diethylstilbestrol (DES) exposure in utero. Following the ban of DES in 1979, CCEA rarely occurs in young women, but still remains...

  12. The set-up for forward scattered particle detection at the external microbeam facility of the INFN-LABEC laboratory in Florence

    International Nuclear Information System (INIS)

    Giuntini, L.; Massi, M.; Calusi, S.; Gelli, N.; Castelli, L.; Carraresi, L.; Czelusniak, C.; Fedi, M.E.; Gueli, A.M.; Liccioli, L.; Mandò, P.A.; Mazzinghi, A.; Palla, L.

    2015-01-01

    In the last few years some new implementations and upgrades have been made to the external scanning microbeam of INFN-LABEC laboratory in Florence, enriching the existing PIXE, PIGE, BS, IBIL set-up with complementary techniques, when possible allowing for simultaneous multi-technique analyses. We developed a system, compatible with the existing set-up, for the out-of-vacuum detection of the forward scattered particles. This system makes feasible the external-STIM (Scanning Transmission Ion Microscopy) and external-FS (Forward Scattering), now both available at our beamline. Test measurements are shortly presented

  13. Hvem var morderen?

    DEFF Research Database (Denmark)

    Andersen, Lene Vinther

    2014-01-01

    Folkemindesamleren og forfatteren Helene Strange (1874-1943) skrev flere gange om et giftmord på en præst på Nordfalster i 1755. Hun satte spørgsmålstegn ved højesteretsdommen og hævdede, at en uskyldig pige blev dømt, mens den virkelige morder slap fri. Det var folkets uskrevne dom, som i over...... hundrede år var blevet fortalt mundtligt videre på egnen, og hun forsøgte – med forskellige midler – at få bragt denne version af historien frem i offentligheden....

  14. Simultaneous determination of 14N and 15N isotopes in opium by proton induced γ-ray emission technique

    International Nuclear Information System (INIS)

    Pritty Rao; Reddy, G.L.N.; Vikram Kumar, S.; Ramana, J.V.; Raju, V.S.; Sanjiv Kumar

    2012-01-01

    The paper describes the simultaneous determination of 14 N and 15 N isotopes in opium by proton induced γ-ray emission (PIGE) technique. The isotopic ratio of 14 N and 15 N is a useful parameter for assigning provenance of (seized) illicit drugs. The measurement, non-destructive in nature, is performed on pellets made up of opium powders and is based on the prompt detection of 2.313 and 4.4 MeV γ-rays emanating from 14 N(p,p'γ) 14 N and 15 N(p,αγ) 12 C nuclear reactions respectively, induced simultaneously by 3.6-3.8 MeV proton beam. Positive as well as negative deviations from the natural isotopic abundance (99.63:0.37) were observed in the samples. The precision of the measurements is about 4%. The methodology provides an easy and rapid approach to determine the isotopic ratio of 14 N and 15 N and has been used for the first time in the analysis of opium. (author)

  15. The visigothic treasure of Torredonjimeno (Jaen, Spain): A study with IBA techniques

    International Nuclear Information System (INIS)

    Perea, A.; Climent-Font, A.; Fernandez-Jimenez, M.; Enguita, O.; Gutierrez, P.C.; Calusi, S.; Migliori, A.; Montero, I.

    2006-01-01

    The visigothic treasure of Torredonjimeno (Jaen, Spain) was found by chance in the year 1926 buried in an olive grove. The finding consisted of some hundreds fragments of gold objects and gems coming from several votive crowns and crosses, some of them belonging to an unidentified visigothic king. The treasure may belong chronologically to the same period as the Guarrazar treasure or, possibly, to a somewhat later time, but the pieces are fragmented and of less technological workmanship than the latter. This is the reason why the Torredonjimeno treasure has not attracted as much attention from archeologists and art historians as that from Guarrazar. On the occasion of an exhibition showing together all the objects of the treasure, it is normally kept in three different museums in Barcelona, Cordoba and Madrid, a number of pieces were analyzed, using PIXE, PIGE and RBS, at the external microbeam facility installed at the Center for Micro-Analysis of Materials

  16. Art, historical and cultural heritage objects studied with different non-destructive analysis

    International Nuclear Information System (INIS)

    Rizzutto, Marcia A.; Tabacniks, Manfredo H.; Added, Nemitala; Campos, Pedro H.O.V.; Curado, Jessica F.; Kajiya, Elizabeth A.M.

    2012-01-01

    Full text: Since 2003, the analysis of art, historical and cultural heritage objects has being performed at the Laboratorio de Analise de Materiais of the Instituto de Fisica of the Universidade de Sao Paulo (LAMFI-USP). Initially the studies were restricted to non-destructive methods using ion beams to characterize the chemical elements present in the objects. Recently, new analytical techniques and procedures have been incorporated to the better characterization of the objects and the examinations were expanded to other non-destructive analytical techniques such as portable X-Ray fluorescence (XRF), digitalized radiography, high resolution photography with visible, UV (ultraviolet) light and reflectography in the infrared region. These non-destructive analytical techniques systematically applied to the objects are helping the better understanding of these objects and allow studying them by examining their main components; their conservation status and also the creative process of the artist, particularly in easel paintings allow making new discoveries. The setup of the external beam in the LAMFI laboratory is configured to allow different simultaneous analysis by PIXE / PIGE (Particle Induced X-ray emission / Particle Induced gamma rays emission), RBS (Rutherford Backscattering) and IBL (Ion Beam Luminescence) and to expand the archaeometric results using ion beams. PIXE and XRF analysis are important to characterize the elements presents in the objects, pigments and others materials. The digitized radiography has provided important information about the internal structure of the objects, the manufacturing process, the internal particles existing and in case of easel paintings it can reveal features of the artist's creative process showing hidden images and the first paintings done by the artist in the background. Some Brazilian paintings studied by IR imaging revealed underlying drawings, which allowed us to discover the process of creation and also some

  17. Art, historical and cultural heritage objects studied with different non-destructive analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rizzutto, Marcia A.; Tabacniks, Manfredo H.; Added, Nemitala; Campos, Pedro H.O.V.; Curado, Jessica F.; Kajiya, Elizabeth A.M. [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica

    2012-07-01

    Full text: Since 2003, the analysis of art, historical and cultural heritage objects has being performed at the Laboratorio de Analise de Materiais of the Instituto de Fisica of the Universidade de Sao Paulo (LAMFI-USP). Initially the studies were restricted to non-destructive methods using ion beams to characterize the chemical elements present in the objects. Recently, new analytical techniques and procedures have been incorporated to the better characterization of the objects and the examinations were expanded to other non-destructive analytical techniques such as portable X-Ray fluorescence (XRF), digitalized radiography, high resolution photography with visible, UV (ultraviolet) light and reflectography in the infrared region. These non-destructive analytical techniques systematically applied to the objects are helping the better understanding of these objects and allow studying them by examining their main components; their conservation status and also the creative process of the artist, particularly in easel paintings allow making new discoveries. The setup of the external beam in the LAMFI laboratory is configured to allow different simultaneous analysis by PIXE / PIGE (Particle Induced X-ray emission / Particle Induced gamma rays emission), RBS (Rutherford Backscattering) and IBL (Ion Beam Luminescence) and to expand the archaeometric results using ion beams. PIXE and XRF analysis are important to characterize the elements presents in the objects, pigments and others materials. The digitized radiography has provided important information about the internal structure of the objects, the manufacturing process, the internal particles existing and in case of easel paintings it can reveal features of the artist's creative process showing hidden images and the first paintings done by the artist in the background. Some Brazilian paintings studied by IR imaging revealed underlying drawings, which allowed us to discover the process of creation and also some

  18. New developments for the analysis of archaeological and artistic artifacts by optical and ion beam methods at LAMFI

    International Nuclear Information System (INIS)

    Rizzutto, Marcia A.; Tabacniks, Manfredo H.; Barbosa, Marcel D. L.; Added, Nemitala; Curado, Jessica F.; Kajiya, Elizabet M.; Campos, Pedro H.O.V. de

    2011-01-01

    Full text: Since 2005, the analysis of artistic and cultural heritage objects at LAMFI-USP (Laboratorio de Analises de Materiais com Feixes Ionicos), initially restricted to ion beam methods, is growing steadily. Since then, alternative methodologies and procedures have been incorporated to better characterize these objects, that possess distinctive physical characteristics and also due to their high cultural and monetary value. The examinations were expanded to other non-destructive analytical techniques like portable XRF (X-ray fluorescence) analysis, X-ray radiography, visible, UV (ultraviolet) and IR (infrared) light imaging that are helping to better understand these art objects, particularly paintings, where the techniques are helping to access the conservation state and also reveal underlying drawings, which help understanding the creative process of the artist. The external beam arrangement at LAMFI was recently updated for simultaneous PIXE (Particle induced X-ray emission), RBS (Rutherford back scattering), PIGE (Particle induced gamma-ray emission) and IBL (Ion beam luminescence) analysis in open air. The new setup comprises a 2 π star-like detector assembly with 7 collimated telescopes: two openings have laser beams for optical alignment of the target, 2 are used for X-ray detectors, 1 for a particle detector, 1 for an optical spectrometer, and 1 for a image. The particle and X-ray detector telescopes can be evacuated to reduce signal losses. The 2 telescopes with the X-ray detectors have absorbers to selectively filter low energy X-rays, optimizing the PIXE detection limits. The beam exit window is made of an 8 μm aluminum foil to monitoring integrated beam charge by measuring the Al gamma rays with a NaI detector. The geometry and materials of the assembly have been carefully designed to shield the X-ray detectors from measuring the X-rays from the exit beam window as well as reducing the detection of Ar K α from the in air beam path. The new

  19. New developments for the analysis of archaeological and artistic artifacts by optical and ion beam methods at LAMFI

    Energy Technology Data Exchange (ETDEWEB)

    Rizzutto, Marcia A.; Tabacniks, Manfredo H.; Barbosa, Marcel D. L.; Added, Nemitala; Curado, Jessica F.; Kajiya, Elizabet M.; Campos, Pedro H.O.V. de [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Fisica

    2011-07-01

    Full text: Since 2005, the analysis of artistic and cultural heritage objects at LAMFI-USP (Laboratorio de Analises de Materiais com Feixes Ionicos), initially restricted to ion beam methods, is growing steadily. Since then, alternative methodologies and procedures have been incorporated to better characterize these objects, that possess distinctive physical characteristics and also due to their high cultural and monetary value. The examinations were expanded to other non-destructive analytical techniques like portable XRF (X-ray fluorescence) analysis, X-ray radiography, visible, UV (ultraviolet) and IR (infrared) light imaging that are helping to better understand these art objects, particularly paintings, where the techniques are helping to access the conservation state and also reveal underlying drawings, which help understanding the creative process of the artist. The external beam arrangement at LAMFI was recently updated for simultaneous PIXE (Particle induced X-ray emission), RBS (Rutherford back scattering), PIGE (Particle induced gamma-ray emission) and IBL (Ion beam luminescence) analysis in open air. The new setup comprises a 2 {pi} star-like detector assembly with 7 collimated telescopes: two openings have laser beams for optical alignment of the target, 2 are used for X-ray detectors, 1 for a particle detector, 1 for an optical spectrometer, and 1 for a image. The particle and X-ray detector telescopes can be evacuated to reduce signal losses. The 2 telescopes with the X-ray detectors have absorbers to selectively filter low energy X-rays, optimizing the PIXE detection limits. The beam exit window is made of an 8 {mu}m aluminum foil to monitoring integrated beam charge by measuring the Al gamma rays with a NaI detector. The geometry and materials of the assembly have been carefully designed to shield the X-ray detectors from measuring the X-rays from the exit beam window as well as reducing the detection of Ar K {alpha} from the in air beam path. The

  20. OLDAPS: Obsidian Least Destructive Analysis Provenancing System

    Energy Technology Data Exchange (ETDEWEB)

    Eder, F.M.; Sterba, J.H.; Bichler, M. [Atominstitut, Vienna University of Technology, Vienna (Austria); Neelmeijer, C.; Merchel, S. [Helmholtz-Zentrum Dresden-Rossendorf (HZDR), Dresden (Germany); Pearce, N.J.G. [Institute of Geography and Earth Sciences, Aberystwyth University, Wales (United Kingdom)

    2013-07-01

    Full text: The natural volcanic glass obsidian is one of the classical objects of archaeometric analyses. Reliable provenancing by means of the highly specific chemical composition, the 'chemical fingerprint', can provide information about trading routes, extension of territory, long-distance contacts and the mobility of prehistoric people. Since the pioneer work of Cann and Renfrew in 1964 [1] various analytical methods have been employed on obsidian samples in order to locate their provenance. The existing data already offers important knowledge about long-distance interactions between prehistoric human populations. However, most applied techniques just show a small part of the element spectrum. Latest studies showed that published results gained by different analytical methods are not consistent due to systematic errors [2-3]. Therefore, the application of three complementary analytical techniques on the same set of raw material samples allows both a better characterization of obsidian sources and a comparison and validation of analytical results. The aim of this multi-methodical approach is to apply in particular: 1) lon Beam Analysis (IBA) comprising of Particle Induced X-ray Emission (PIXE) and Particle Induced Gamma-ray Emission (PIGE), 2) Instrumental Neutron Activation Analysis (INAA), 3) Laser Ablation-lnductively Coupled Plasma-Mass Spectrometry (LA-ICP-MS), to detect a maximum element spectrum and to compare element concentrations determined with at least two analytical techniques. This approach should check the accuracy and reliability of analytical results and should show a maximum of compositional differences between European obsidian sources to reveal the most characteristic 'chemical fingerprint' composed of more than 40 elements. These investigations are part of a new multi-methodical analytical database called the 'Obsidian Least Destructive Analysis Provenancing System' (OLDAPS). This novel scientific approach for

  1. Nuclear reaction data for IBA applications to cultural heritage diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Maino, G.; Menapace, E. [Bologna Univ., ENEA (Italy)

    2008-07-01

    Main aspects are discussed concerning nuclear reaction cross-sections for PIXE and PIGE (Particle Induced Gamma-ray Emission) analyses, especially referring to cultural heritage diagnostics, within the framework of ion beam analysis (IBA) methods, also reviewing recent results from international Conferences on Nuclear Data for Science and Technology and from NEANSC meetings and IAEA initiatives on the matter.To sum up this work, it is then worth remarking the following items: IBA techniques are powerful tools to derive unique information as for corrosion, degradation and, generally, conservation conditions of materials. Careful analyses of specific systems require accurate evaluations and establishment of complete databases, in particular for stopping powers and relevant cross sections. The physical parameters to be accurately determined are, therefore, nuclear reaction cross sections of importance for NRA analysis of light elements and stopping powers and ranges of light and heavy ions in various matrices. Light elements (H, Li, B, C, N, O, etc.) play an important role as constituents of many important organic as well inorganic materials in historical and artistic objects. To a large extent these materials occur in the near-surface area of a material with altered or degraded composition.

  2. Nuclear reaction data for IBA applications to cultural heritage diagnostics

    International Nuclear Information System (INIS)

    Maino, G.; Menapace, E.

    2008-01-01

    Main aspects are discussed concerning nuclear reaction cross-sections for PIXE and PIGE (Particle Induced Gamma-ray Emission) analyses, especially referring to cultural heritage diagnostics, within the framework of ion beam analysis (IBA) methods, also reviewing recent results from international Conferences on Nuclear Data for Science and Technology and from NEANSC meetings and IAEA initiatives on the matter.To sum up this work, it is then worth remarking the following items: IBA techniques are powerful tools to derive unique information as for corrosion, degradation and, generally, conservation conditions of materials. Careful analyses of specific systems require accurate evaluations and establishment of complete databases, in particular for stopping powers and relevant cross sections. The physical parameters to be accurately determined are, therefore, nuclear reaction cross sections of importance for NRA analysis of light elements and stopping powers and ranges of light and heavy ions in various matrices. Light elements (H, Li, B, C, N, O, etc.) play an important role as constituents of many important organic as well inorganic materials in historical and artistic objects. To a large extent these materials occur in the near-surface area of a material with altered or degraded composition

  3. Characterization and source apportionment of fine particulate sources at Rijeka, Croatia from 2013 to 2015

    International Nuclear Information System (INIS)

    Ivošević, Tatjana; Stelcer, Eduard; Orlić, Ivica; Bogdanović Radović, Iva; Cohen, David

    2016-01-01

    PM_2_._5 daily aerosol samples were collected in Rijeka, Croatia during period from 6th August 2013 to 29th January 2015. In total, 259 samples were collected on Teflon filters and analyzed by PIXE and PIGE techniques to give information on 21 elements from Na to Pb. Additionally, black carbon was determined with the Laser Integrated Plate Method. Results were statistically evaluated using Positive Matrix Factorization (PMF). Eight major pollution sources: auto, smoke, secondary sulfates, heavy oil combustion, sea spray, road dust, industry iron and soil dust were identified together with their relative contributions in total PM_2_._5 pollution.

  4. SigmaCalc recent development and present status of the evaluated cross-sections for IBA

    Energy Technology Data Exchange (ETDEWEB)

    Gurbich, A.F.

    2016-03-15

    A new version of the SigmaCalc Internet site ( (http://sigmacalc.iate.obninsk.ru)) intended to provide evaluated differential cross-sections for spectra simulation is presented. Results of the revision of previously evaluated cross-sections and new evaluations including data for PIGE were made available to the IBA community through a simple interface. New SigmaCalc features allow users to compare evaluated differential cross-sections with the available results of the cross-section measurements taken on-the-fly from the IBANDL database and to validate them against benchmarks. The current status of the evaluated cross-sections for IBA is discussed.

  5. Measurement of proton induced thick target γ-ray yields on B, N, Na, Al and Si from 2.5 to 4.1 MeV

    Energy Technology Data Exchange (ETDEWEB)

    Chiari, M., E-mail: chiari@fi.infn.it [INFN-Florence and Department of Physics and Astronomy, University of Florence, via G. Sansone 1, 50019 Sesto Fiorentino (Italy); Ferraccioli, G.; Melon, B.; Nannini, A.; Perego, A.; Salvestrini, L. [INFN-Florence and Department of Physics and Astronomy, University of Florence, via G. Sansone 1, 50019 Sesto Fiorentino (Italy); Lagoyannis, A.; Preketes-Sigalas, K. [Tandem Accelerator Laboratory, Institute of Nuclear and Particle Physics, NCSR “Demokritos”, 153.10 Aghia Paraskevi, Athens (Greece)

    2016-01-01

    Thick target yields for proton induced γ-ray emission (PIGE) on low-Z nuclei, namely B, N, Na, Al and Si, were measured for proton energies from 2.5 to 4.1 MeV and emission angles of 0°, 45° and 90°, at the 3 MV Tandetron laboratory of INFN-LABEC in Florence. The studied reactions were: {sup 10}B(p,α′γ){sup 7}Be (E{sub γ} = 429 keV), {sup 10}B(p,p′γ){sup 10}B (E{sub γ} = 718 keV) and {sup 11}B(p,p′γ){sup 11}B (E{sub γ} = 2125 keV) for boron; {sup 14}N(p,p′γ){sup 14}N (E{sub γ} = 2313 keV) for nitrogen; {sup 23}Na(p,p′γ){sup 23}Na (E{sub γ} = 441 and 1636 keV) and {sup 23}Na(p,α′γ){sup 20}Ne (E{sub γ} = 1634 keV) for sodium; {sup 27}Al(p,p′γ){sup 27}Al (E{sub γ} = 844 and 1014 keV) and {sup 27}Al(p,α′γ){sup 24}Mg (E{sub γ} = 1369 keV) for aluminum; {sup 28}Si(p,p′γ){sup 28}Si (E{sub γ} = 1779 keV) and {sup 29}Si(p,p′γ){sup 29}Si (E{sub γ} = 1273 keV) for silicon. The PIGE thick target yields have been measured with an overall uncertainty typically better than 10%. The use of the measured thick target yield to benchmark and validate experimental cross sections available in the literature is demonstrated.

  6. Application of photo-detection to art and archaeology at the C2RMF

    Science.gov (United States)

    Calligaro, T.; Dran, J.-C.; Klein, M.

    2003-05-01

    The Centre for research and restoration of the museums of France (C2RMF), located in the Louvre palace in Paris routinely uses photodetector-based techniques for the study of objects of cultural heritage. Among these methods, the ion beam analysis techniques (IBA) provided by the 2-MV electrostatic accelerator "AGLAE" installed in the C2RMF have the specific qualities required for the study of these valuable objects. Indeed, PIXE and PIGE are non-destructive, non-invasive, rapid and sensitive tools for the determination of the chemical composition. Their use enables to answer three major questions in the field of Art and Archaeology: (1) identification of the material, (2) determination of the provenance, and (3) study of surface modification (ageing, alteration). Applications of radiation detectors are exemplified through case studies performed at the Centre: the identification of the pigments used on an Egyptian papyrus, the provenance of gemstones set on ancient jewels and the indirect dating of archaeological flints. New trends in the use of photo-detectors in Art and Archaeology are presented.

  7. Application of photo-detection to art and archaeology at the C2RMF

    International Nuclear Information System (INIS)

    Calligaro, T.; Dran, J.-C.; Klein, M.

    2003-01-01

    The Centre for research and restoration of the museums of France (C2RMF), located in the Louvre palace in Paris routinely uses photodetector-based techniques for the study of objects of cultural heritage. Among these methods, the ion beam analysis techniques (IBA) provided by the 2-MV electrostatic accelerator 'AGLAE' installed in the C2RMF have the specific qualities required for the study of these valuable objects. Indeed, PIXE and PIGE are non-destructive, non-invasive, rapid and sensitive tools for the determination of the chemical composition. Their use enables to answer three major questions in the field of Art and Archaeology: (1) identification of the material, (2) determination of the provenance, and (3) study of surface modification (ageing, alteration). Applications of radiation detectors are exemplified through case studies performed at the Centre: the identification of the pigments used on an Egyptian papyrus, the provenance of gemstones set on ancient jewels and the indirect dating of archaeological flints. New trends in the use of photo-detectors in Art and Archaeology are presented

  8. Application of photo-detection to art and archaeology at the C2RMF

    Energy Technology Data Exchange (ETDEWEB)

    Calligaro, T. E-mail: thomas.calligaro@culture.gouv.fr; Dran, J.-C.; Klein, M

    2003-05-21

    The Centre for research and restoration of the museums of France (C2RMF), located in the Louvre palace in Paris routinely uses photodetector-based techniques for the study of objects of cultural heritage. Among these methods, the ion beam analysis techniques (IBA) provided by the 2-MV electrostatic accelerator 'AGLAE' installed in the C2RMF have the specific qualities required for the study of these valuable objects. Indeed, PIXE and PIGE are non-destructive, non-invasive, rapid and sensitive tools for the determination of the chemical composition. Their use enables to answer three major questions in the field of Art and Archaeology: (1) identification of the material, (2) determination of the provenance, and (3) study of surface modification (ageing, alteration). Applications of radiation detectors are exemplified through case studies performed at the Centre: the identification of the pigments used on an Egyptian papyrus, the provenance of gemstones set on ancient jewels and the indirect dating of archaeological flints. New trends in the use of photo-detectors in Art and Archaeology are presented.

  9. Characterization and source apportionment of fine particulate sources at Rijeka, Croatia from 2013 to 2015

    Energy Technology Data Exchange (ETDEWEB)

    Ivošević, Tatjana, E-mail: tatjana.ivosevic14@gmail.com [Faculty of Engineering, University of Rijeka, Vukovarska 58, HR-51000 Rijeka (Croatia); Stelcer, Eduard [Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Orlić, Ivica [Department of Physics, University of Rijeka, Radmile Matejčić 2, HR-51000 Rijeka (Croatia); Bogdanović Radović, Iva [Laboratory for Ion Beam Interactions, Ruđer Bošković Institute, Bijenička 54, HR-10000 Zagreb (Croatia); Cohen, David [Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia)

    2016-03-15

    PM{sub 2.5} daily aerosol samples were collected in Rijeka, Croatia during period from 6th August 2013 to 29th January 2015. In total, 259 samples were collected on Teflon filters and analyzed by PIXE and PIGE techniques to give information on 21 elements from Na to Pb. Additionally, black carbon was determined with the Laser Integrated Plate Method. Results were statistically evaluated using Positive Matrix Factorization (PMF). Eight major pollution sources: auto, smoke, secondary sulfates, heavy oil combustion, sea spray, road dust, industry iron and soil dust were identified together with their relative contributions in total PM{sub 2.5} pollution.

  10. A new ion beam facility based on a 3 MV Tandetron™ at IFIN-HH, Romania

    Science.gov (United States)

    Burducea, I.; Straticiuc, M.; Ghiță, D. G.; Moșu, D. V.; Călinescu, C. I.; Podaru, N. C.; Mous, D. J. W.; Ursu, I.; Zamfir, N. V.

    2015-09-01

    A 3 MV Tandetron™ accelerator system has been installed and commissioned at the "Horia Hulubei" National Institute for Physics and Nuclear Engineering - IFIN-HH, Măgurele, Romania. The main purpose of this machine is to strengthen applied nuclear physics research ongoing in our institute for more than four decades. The accelerator system was developed by High Voltage Engineering Europa B.V. (HVE) and comprises three high energy beam lines. The first beam line is dedicated to ion beam analysis (IBA) techniques: Rutherford Backscattering Spectrometry - RBS, Nuclear Reaction Analysis - NRA, Particle Induced X-ray and γ-ray Emission - PIXE and PIGE and micro-beam experiments - μ-PIXE. The second beam line is dedicated to high energy ion implantation experiments and the third beam line was designed mainly for nuclear cross-sections measurements used in nuclear astrophysics. A unique feature, the first time in operation at an accelerator facility is the Na charge exchange canal (CEC), which is used to obtain high intensity beams of He- of at least 3 μA. The results of the acceptance tests demonstrate the huge potential of this new facility in various fields, from IBA to radiation hardness studies and from medical or environmental applications to astrophysics. The main features of the accelerator are presented in this paper.

  11. PIGE - Resonance profiling applied to a clinical test of flouride varnishes

    Science.gov (United States)

    Zschau, H. E.; Plier, F.; Otto, G.; Wyrwich, C.; Treide, A.

    1992-03-01

    A clinical in-vivo experiment had been carried out to compare two caries preventing fluorine varnishes. The fluorine depth profiles in the near surface region of tooth enamel were measured using the 935 keV resonance of the nuclear reaction 19F( p, p' γ) 19F. The results can be understood by studying the flourine anamnese of the patients.

  12. Oral og verbal dyspraksi hos en i øvrigt rask pige

    DEFF Research Database (Denmark)

    Nikoghosyan-Bossen, Gohar

    2018-01-01

    In the absence of any known neurological condition, dyspraxia is the inability to plan and execute movement. This case report describes a girl with swallowing difficulties, who was diagnosed with oral dyspraxia, as all other possible explanations had been ruled out. A percutaneous endoscopic...... gastrostomy was performed at the age of 6.5 months, and as a five-year-old she was still dependent on supplementary nutrition through the tube, even though she had gradually learned to swallow. Her difficulties to correctly pronounce syllables and words were later diagnosed as childhood apraxia of speech...

  13. Juvenilt gigant fibroadenom i brystet hos en tiårig pige

    DEFF Research Database (Denmark)

    Hasanbegovic, Emir; Talman, Maj-Lis Møller; Hjalgrim, Lisa Lyngsie

    2014-01-01

    A rapidly growing mass in the breast may be stressful for both parents and child as the suspicion of malignancy arises. The purpose of this case report is to draw attention to the fact that most emerging lesions of the breast in girls during puberty are benign. This case report presents a ten-yea......-year-old girl with a rapidly growing tumour in the breast. The tumour turned out to be a giant juvenile fibroadenoma, which is rare and benign. Differential diagnosis, investigation and management are reviewed....

  14. Juvenilt gigant fibroadenom i brystet hos en tiårig pige

    DEFF Research Database (Denmark)

    Hasanbegovic, Emir; Talman, Maj-Lis; Hjalgrim, Lisa Lyngsie

    2014-01-01

    A rapidly growing mass in the breast may be stressful for both parents and child as the suspicion of malignancy arises. The purpose of this case report is to draw attention to the fact that most emerging lesions of the breast in girls during puberty are benign. This case report presents a ten-yea...

  15. The upgraded external-beam PIXE/PIGE set-up at LABEC for very fast measurements on aerosol samples

    Energy Technology Data Exchange (ETDEWEB)

    Lucarelli, F., E-mail: lucarelli@fi.infn.it; Calzolai, G.; Chiari, M.; Giannoni, M.; Mochi, D.; Nava, S.; Carraresi, L.

    2014-01-01

    At the 3 MV Tandetron accelerator of the LABEC laboratory of INFN in Florence, an external beam facility is fully dedicated to measurements of elemental composition of atmospheric aerosol. The experimental set-up hitherto used for this kind of applications has been upgraded with the replacement of a traditional Si(Li) detector for the detection of medium–high Z elements with a silicon drift detector (SDD) with a big active area (80 mm{sup 2}) and 450 μm thickness, with the aim of obtaining better minimum detection limits (MDL) and reduce measuring times. The Upilex extraction window has been replaced by a more resistant one (Si{sub 3}N{sub 4}). A comparison between the old Si(Li) and the new SDD for aerosol samples collected on different substrata like Teflon, Kapton and Nuclepore evidenced the better performances of the SDD. It allows obtaining better results (higher counting statistics, lower MDLs) even in shorter measuring times, thus allowing very fast analysis of both daily and hourly samples.

  16. Corrosion of 15th and early 16th century stained glass from the monastery of Batalha studied with external ion beam

    Energy Technology Data Exchange (ETDEWEB)

    Vilarigues, M., E-mail: mgv@fct.unl.pt [Dep. de Conservacao e Restauro and Centro do Vidro e da Ceramica para as Artes, FCT-UNL, Quinta da Torre, 2829-516 Caparica (Portugal); Redol, P. [Dep. de Conservacao e Restauro and Centro do Vidro e da Ceramica para as Artes, FCT-UNL, Quinta da Torre, 2829-516 Caparica (Portugal); Monastery of Batalha, P-2440 (Portugal); Machado, A. [Dep. de Conservacao e Restauro and Centro do Vidro e da Ceramica para as Artes, FCT-UNL, Quinta da Torre, 2829-516 Caparica (Portugal); Rodrigues, P.A.; Alves, L.C.; Silva, R.C. da [Dep. Fisica, LFI, ITN, E.N.10, 2686-953 Sacavem (Portugal)

    2011-02-15

    This paper reports the study of corrosion in two stained glass panels from the south aisle of Sta. Maria da Vitoria monastery, at Batalha (Portugal), one depicting the Last Supper (dated from 1508), and the other one showing a saint (c. 1450). These panels exhibit extensive corrosion with darkening phenomena that are an impediment to their correct visualization, a source of major concern both to conservators and curators. By using external micro-beam Particle Induced X-ray Emission (PIXE) and Particle Induced Gamma Emission (PIGE) spectrometry, the elemental compositions of large fragments were obtained, enabling the selection of representative corroded areas, from which elemental distribution maps were produced by scanning. Calcium and potassium rich structures were found - at the surface and inside cavities in the glass - that were identified as oxalates and carbonates, by Raman microscopy and micro-FTIR. The dark spots present in the glass surfaces were found to be Zn and Pb rich. These findings indicate that the corrosion observed was due not only to reactions with atmospheric water and CO{sub 2} but also with the oxalic acid secreted by micro-organisms. Furthermore, it did not result from reactions with atmospheric SO{sub 2} or acid rain. The information obtained is relevant for a better understanding of the corrosion processes and products formed on the surface of these panels and therefore for the proper planning of much needed adequate conservation-restoration actions and appropriate display conditions. - Research Highlights: {yields} Corrosion and darkening of stained glasses is of concern to conservators and curators. {yields} A multi-technique approach is of relevance to study stained glass corrosion. {yields} External beam PIXE-PIGE provide valuable insight on stained glass corrosion.

  17. Studies using nuclear and complementary non-nuclear analytical techniques for bio-monitoring of air pollution

    International Nuclear Information System (INIS)

    Arunachalam, J.; Karunasagar, D.; Kumar, S.; Sahayam, A.C.

    1999-01-01

    A set of lower and higher plants have been analysed for their trace element contents. The plants are, a moss (Funaria sp.), a bryophyte (Cyathodium sp.), a weed (Parthenium hysterophorus L.) and a common bushy shrub (Lantana Camera L.). The trace element concentrations have been determined using INAA, PIGE and ICP-OES. The data are examined with a view to assess the use of these plants as bio-indicators of toxic trace metal pollutants in ambient air. The moss and the bryophyte samples show much higher accumulation levels for many elements, but are seasonal. The other two plants, due to their perennial nature, can be used for bio-monitoring purposes, almost throughout the year. (author)

  18. Swift Quantification of Fenofibrate and Tiemonium methylsulfate Active Ingredients in Solid Drugs Using Particle Induced X-Ray Emission

    International Nuclear Information System (INIS)

    Bejjani, A.; Nsouli, B.; Zahraman, K.; Assi, S.; Younes, Gh.; Yazbi, F.

    2011-01-01

    The quantification of active ingredients (AI) in drugs is a crucial and important step in the drug quality control process. This is usually performed by using wet chemical techniques like LC-MS, UV spectrophotometry and other appropriate organic analytical methods. However, if the active ingredient contains specific heteroatoms (F, S, Cl), elemental IBA like PIXE and PIGE techniques, using small tandem accelerator of 1-2 MV, can be explored for molecular quantification. IBA techniques permit the analysis of the sample under solid form, without any laborious sample preparations. In this work, we demonstrate the ability of the Thick Target PIXE technique for rapid and accurate quantification of both low and high concentrations of active ingredients in different commercial drugs. Fenofibrate, a chlorinated active ingredient, is present in high amounts in two different commercial drugs, its quantification was done using the relative approach to an external standard. On the other hand, Tiemonium methylsulfate which exists in relatively low amount in commercial drugs, its quantification was done using GUPIX simulation code (absolute quantification). The experimental aspects related to the quantification validity (use of external standards, absolute quantification, matrix effect,...) are presented and discussed. (author)

  19. Programs for visualization, handling and quantification of PIXE maps at the AGLAE facility

    Energy Technology Data Exchange (ETDEWEB)

    Pichon, L., E-mail: laurent.pichon@culture.fr [Centre de recherche et de restauration des musées de France, C2RMF, Palais du Louvre – Porte des Lions, 14 Quai François Mitterrand, 75001 Paris (France); Fédération de recherche NewAGLAE, FR3506 CNRS, Ministère de la Culture et de la Communication, Chimie ParisTech, Palais du Louvre, 75001 Paris (France); Calligaro, T. [Centre de recherche et de restauration des musées de France, C2RMF, Palais du Louvre – Porte des Lions, 14 Quai François Mitterrand, 75001 Paris (France); Fédération de recherche NewAGLAE, FR3506 CNRS, Ministère de la Culture et de la Communication, Chimie ParisTech, Palais du Louvre, 75001 Paris (France); PSL Research University, Chimie ParisTech-CNRS, Institut de Recherche Chimie Paris, UMR8247, 75005 Paris (France); Lemasson, Q.; Moignard, B.; Pacheco, C. [Centre de recherche et de restauration des musées de France, C2RMF, Palais du Louvre – Porte des Lions, 14 Quai François Mitterrand, 75001 Paris (France); Fédération de recherche NewAGLAE, FR3506 CNRS, Ministère de la Culture et de la Communication, Chimie ParisTech, Palais du Louvre, 75001 Paris (France)

    2015-11-15

    The external beam setup of the AGLAE facility has been developed in order to combine PIXE with PIGE, EBS and recently IBIL for the analysis of cultural heritage artefacts. The upgraded external beam end-station integrates five large solid angle X-ray detectors either to reduce the risk of damage on sensitive artworks by decreasing the beam intensity or to routinely acquire elemental maps at various scales. While many programs are available to process PIXE maps acquired with nuclear microprobes, a software to process the major and trace elements PIXE maps point by point using GUPIX is not available. The present paper describes three programs developed for the AGLAE facility to process numerous maps obtained with multiple detectors. AGLAEMAP allows to handle maps and pixel groups within maps, TRAUPIXE to process quantitatively PIXE spectra of all pixels and DATAIMAGING to display the resulting quantitative elemental maps. The benefits of this software suite are demonstrated by processing a dataset acquired on a pellet of geostandard reference material and on a terre mêlée pottery shard sample created by the famous ceramist Bernard Palissy (1510–1589), highlighting chemical elements present in this polychrome ceramic.

  20. Programs for visualization, handling and quantification of PIXE maps at the AGLAE facility

    International Nuclear Information System (INIS)

    Pichon, L.; Calligaro, T.; Lemasson, Q.; Moignard, B.; Pacheco, C.

    2015-01-01

    The external beam setup of the AGLAE facility has been developed in order to combine PIXE with PIGE, EBS and recently IBIL for the analysis of cultural heritage artefacts. The upgraded external beam end-station integrates five large solid angle X-ray detectors either to reduce the risk of damage on sensitive artworks by decreasing the beam intensity or to routinely acquire elemental maps at various scales. While many programs are available to process PIXE maps acquired with nuclear microprobes, a software to process the major and trace elements PIXE maps point by point using GUPIX is not available. The present paper describes three programs developed for the AGLAE facility to process numerous maps obtained with multiple detectors. AGLAEMAP allows to handle maps and pixel groups within maps, TRAUPIXE to process quantitatively PIXE spectra of all pixels and DATAIMAGING to display the resulting quantitative elemental maps. The benefits of this software suite are demonstrated by processing a dataset acquired on a pellet of geostandard reference material and on a terre mêlée pottery shard sample created by the famous ceramist Bernard Palissy (1510–1589), highlighting chemical elements present in this polychrome ceramic.

  1. Fluorine determination in human healthy and carious teeth using the PIGE technique

    International Nuclear Information System (INIS)

    Carvalho, M.L.; Karydas, A.G.; Casaca, C.; Zarkadas, Ch.; Paradellis, Th.; Kokkoris, M.; Nsouli, B.; Cunha, A.S.

    2001-01-01

    The purpose of this study is to determine and compare the fluorine concentration in human teeth from two different populations, living in the Portuguese quite isolated islands of Acores: S. Miguel and Terceira. Both populations have similar dietary habits, similar occupational activities, mostly rural, and the age of both populations is more or less the same, around 40 years. No chronic diseases were registered in any of the donors. The two groups are exposed to different levels of fluorine in drinking water. Terceira island has moderate fluorine concentration levels (1-2 μg g -1 ) while S. Miguel island is known for the high fluorine concentration levels in its water (>3 μg g -1 ), especially in one area known as Furnas. Thirty-three teeth, 17 healthy and 16 carious without restoration (14 incisors and canines, 7 premolars and 12 molars), were collected and analyzed for the determination of fluorine concentration in the dentine region, using the nuclear reaction 19 F(p,αγ) 16 O. The teeth were cross-sectioned along the vertical plane and polished, in order to obtain a smooth and plane surface of about 1 mm thickness. In this work an association between caries prevalence and fluorine content of drinking water is discussed and the variation of fluorine concentration among different types of teeth (canines and incisors, premolars, molars) and physical state (carious and non-carious) is examined

  2. Duplikationscyste som årsag til ileus hos en 16-årig pige

    DEFF Research Database (Denmark)

    Buch, Anastasia S; Virkus, Rie Adser

    2018-01-01

    A 16-year-old girl was admitted to hospital with lower abdominal pain. An ultrasound examination suggested an ovarian cyst. A laparoscopic procedure found that a duplication cyst in the patient's ileum had caused mechanical ileus. The cyst was surgically resected through the creation of an end-to...

  3. The new external ion beam analysis setup at the Demokritos Tandem accelerator and first applications in cultural heritage

    International Nuclear Information System (INIS)

    Sokaras, Dimosthenis; Bistekos, Euthimios; Georgiou, Lambros; Salomon, Joseph; Bogovac, Mladen; Aloupi-Siotis, Eleni; Paschalis, Vasilis; Aslani, Ioanna; Karabagia, Sofia; Lagoyannis, Anastasios; Harissopulos, Sotirios; Kantarelou, Vasiliki; Karydas, Andreas-Germanos

    2011-01-01

    At the 5.5 MV Tandem VdG accelerator of the Institute of Nuclear Physics of N.C.S.R. 'Demokritos', Athens, Greece, an external ion-beam set-up has been recently developed and installed. The aim of this development was to integrate the analytical capabilities of the PIXE, RBS and PIGE ion beam techniques in one experimental set-up, so that to attain a complete elemental and near surface structural characterization of samples in an almost non-destructive way and without any limitation concerning their size or conductive state. A careful 3D mechanical drawing optimized the set-up experimental parameters achieving probe dimensions at the millimeter range (1 mm 2 ) and fulfilling the special requirements imposed for optimum performance of the aforementioned techniques, including the possibility to use heavier, than protons, ion beams. For the digital pulse processing of the X-ray, γ-ray and charged particle detector signals, novel hardware and software tools were developed based on a custom FPGA configuration. The first applications were focused in the quality control of materials that have been intentionally contaminated with a particular tracer-element ('tagged' materials). The tagged materials which were developed and tested are technologically authentic replicas of ancient attic ceramics with black glazed decoration. Analytical diagnostic studies were carried out for a few representative paintings of contemporary Greek painters in order to identify and document materials/pigments and techniques and eventually to prevent trade of fakes. Finally, ancient glass beads were also examined with respect to the sodium concentration and its in-depth homogeneity.

  4. Dicty_cDB: Contig-U15349-1 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available us petioles cDNA library Populus tre... 38 0.58 2 ( AP006852 ) Candida albicans genomic ...CT049626 ) Sus scrofa genomic clone PigE-217H19, genomic sur... 48 0.79 1 ( EG687952 ) RCRBD08TO Castor bean cDNA library...V246458 ) A2FO395TO Aedes aegypti full length cDNA library,... 48 0.79 1 ( DV246174 ) A2FMO77TV Aedes aegypti full length cDNA librar...y,... 48 0.79 1 ( DV231005 ) A1FL491TO Aedes aegypti full length cDNA library,... 4.... 50 0.20 1 ( AZ428968 ) 1M0212M05R Mouse 10kb plasmid UUGC1M library Mus ... 50 0.20 1 ( CR123377 ) Reverse strand re

  5. A particle accelerator probes artifacts

    International Nuclear Information System (INIS)

    Dran, J.C.; Calligaro, Th.; Salomon, J.

    2002-01-01

    The AGLAE system is made up of a 2 mega volts electrostatic accelerator and of 3 irradiation lines: one leads to a vacuum enclosure in which targets are irradiated and the 2 others lines are designed to irradiate targets under an air or helium atmosphere. The AGLAE system is located in the premises of the Louvre museum in Paris and is devoted to the study of cultural objects through ion beam analysis (IBA). 4 techniques are used: -) proton-induced X-ray emission (PIXE) -) proton-induced gamma ray (PIGE) -) Rutherford backscattering spectrometry (NRS) and -) nuclear reaction analysis (NRA). A decisive progress has permitted the direct analysis of artifacts without sampling. The object itself is set just a few millimeters away from the exit window of the beam in an air or helium atmosphere. The exit window must be resistant enough to bear the atmospheric pressure and the damages caused by the proton beam but must be thin enough to not deteriorate the quality of the beam. By using a 10 -7 m thick exit window made of Si 3 N 4 we get a beam whose diameter is 10 -5 m. This new technology presents 4 main advantages: 1) any object of any shape can be studied without sampling, 2) the analysis of very fragile artifacts that might be damaged by the vacuum setting is now possible, 3) a reduction of the thermal side-effects of the beam, and 4) the absence of accumulation of charges in isolating material allows to rid of covering the object with a conducting coating before irradiating it. (A.C.)

  6. Malign ovarietumor som årsag til virilisering af en 12-årig pige

    DEFF Research Database (Denmark)

    Vestergård Andersen, Dorthe; Hermansen, Mette Northman

    2012-01-01

    Virilisation in girls includes androgen dependent growth of terminal hair, acne, deepening of the voice and increased muscle mass. Sudden onset of symptoms, rapid progression, short duration and hyperandrogenaemia are ominous signs and the patient must be referred to a specialist as soon as possi......Virilisation in girls includes androgen dependent growth of terminal hair, acne, deepening of the voice and increased muscle mass. Sudden onset of symptoms, rapid progression, short duration and hyperandrogenaemia are ominous signs and the patient must be referred to a specialist as soon...

  7. Experimental nuclear physics research in Hungary

    International Nuclear Information System (INIS)

    Koltay, Ede.

    1984-01-01

    The status and recent results of experimental nuclear physics in Hungary is reviewed. The basic nuclear sciences, instrumental background and international cooperation are discussed. Personal problems and the effects of the international scientific deconjuncture are described. The applied nuclear and interdisciplinary researches play an important role in Hungarian nuclear physics. Some problems of cooperation of Hungarian nuclear and other research institutes applying or producing nuclear analytical technology are reviewed. The new instrument, the Debrecen cyclotron under construction gives new possibilities to basic and applied researches. A new field of Hungarian nuclear physics is the fusion and plasma research using tokamak equipment, the main topics of which are plasma diagnostics and fusion control systems. Some practical applications of Hungarian nuclear physical results, e.g. establishment of new analytical techniques like PIXE, RBS, PIGE, ESCA, etc. are summarized. (D.Gy.)

  8. Carbon ion induced DNA double-strand breaks in melanophore B{sub 16}

    Energy Technology Data Exchange (ETDEWEB)

    Zengquan, Wei; Guangming, Zhou; Jufang, Wang; Jing, He; Qiang, Li; Wenjian, Li; Hongmei, Xie; Xichen, Cai; Huang, Tao; Bingrong, Dang; Guangwu, Han [Chinese Academy of Sciences, Lanzhou (China). Inst. of Modern Physics; Qingxiang, Gao [Lanzhou Univ. (China)

    1997-09-01

    DNA double-strand breaks (DSBs) in melanophore B{sub 16} induced by plateau and extended Bragg peak of 75 MeV/u {sup 12}C{sup 6+} ions were studied by using a technique of inverse pulsed-field gel electrophoresis (PIGE). DNA fragment lengths were distributed in two ranges: the larger in 1.4 Mbp-3.2 Mbp and the smaller in less than 1.2 Mbp. It indicates that distribution of DNA fragments induced by heavy ion irradiation is not stochastic and there probably are sensitive sites to heavy ions in DNA molecules of B{sub 16}. Percentage of DNA released from plug (PR) increased and trended towards a quasi-plateau {proportional_to}85% as dose increased. Content of the larger fragments decreased and flattened with increasing dose while content of the smaller ones increased and trended towards saturation. (orig.)

  9. Carbon ion induced DNA double-strand breaks in melanophore B16

    International Nuclear Information System (INIS)

    Wei Zengquan; Zhou Guangming; Wang Jufang; He Jing; Li Qiang; Li Wenjian; Xie Hongmei; Cai Xichen; Tao Huang; Dang Bingrong; Han Guangwu

    1997-01-01

    DNA double-strand breaks (DSBs) in melanophore B 16 induced by plateau and extended Bragg peak of 75 MeV/u 12 C 6+ ions were studied by using a technique of inverse pulsed-field gel electrophoresis (PIGE). DNA fragment lengths were distributed in two ranges: the larger in 1.4 Mbp-3.2 Mbp and the smaller in less than 1.2 Mbp. It indicates that distribution of DNA fragments induced by heavy ion irradiation is not stochastic and there probably are sensitive sites to heavy ions in DNA molecules of B 16 . Percentage of DNA released from plug (PR) increased and trended towards a quasi-plateau ∝85% as dose increased. Content of the larger fragments decreased and flattened with increasing dose while content of the smaller ones increased and trended towards saturation. (orig.)

  10. PIXE and PGAA - Complementary methods for studies on ancient glass artefacts (from Byzantine, late medieval to modern Murano glass)

    Science.gov (United States)

    Constantinescu, Bogdan; Cristea-Stan, Daniela; Szőkefalvi-Nagy, Zoltán; Kovács, Imre; Harsányi, Ildikó; Kasztovszky, Zsolt

    2018-02-01

    Combined external milli-beam Particle Induced X-ray Emission (PIXE) and Prompt Gamma Activation Analysis (PGAA) analysis was applied to characterize the composition of paste and colorants from some fragments of Byzantine bracelets (10th-12th Centuries AD), late medieval (17th-18th Centuries AD) and modern Murano glass pieces. As fluxes, PGAA revealed the samples are soda-lime glass, except four samples - two medieval vessel white shards and two dark Byzantine fragments of bracelets - which have potash flux. Aluminium was detected in various proportions in all samples indicating different sources for the added sand. The presence of Magnesium is relevant only in one bracelet fragment suggesting the use of plant (wood?) ash and confirming that the Byzantine bracelet is manufactured from the mixture of both types of glass (natron and plant ash based). PGAA also indicated the presence of low quantities of Cadmium, high level of Arsenic and Lead (possibly lead arsenate) in one medieval sample and of ZnO in Murano glass, and of CoO traces (maximum 0.1%) in all blue-colored Byzantine, late medieval to modern Murano glass artefacts. PIXE confirmed the use of small quantities of CoO for blue color, indicated Manganese combined with Iron for dark glass, Copper for green, Lead, Tin and an Arsenic compound (orpiment?) for yellow and in the case of modern Murano glass Selenium and Cadmium to obtain a reddish color. Despite PIXE - PIGE combination is probably the best one for glass analysis, our external milli-PIXE - PGAA methods proved to be adequate complementary tools to determine many chemical elements from glass composition - Si, Na, K, Ca, Al, Mg, various metallic oxides.

  11. The cyclotron laboratory and the RFQ accelerator in Bern

    International Nuclear Information System (INIS)

    Braccini, S.; Ereditato, A.; Kreslo, I.; Nirkko, M.; Weber, M.; Scampoli, P.; Bremen, K. von

    2013-01-01

    Two proton accelerators have been recently put in operation in Bern: an 18 MeV cyclotron and a 2 MeV RFQ linac. The commercial IBA 18/18 cyclotron, equipped with a specifically conceived 6 m long external beam line ending in a separate bunker, will provide beams for routine 18-F and other PET radioisotope production as well as for novel detector, radiation biophysics, radioprotection, radiochemistry and radiopharmacy developments. The accelerator is embedded into a complex building hosting two physics laboratories and four Good Manufacturing Practice (GMP) laboratories. This project is the result of a successful collaboration between the Inselspital, the University of Bern and private investors, aiming at the constitution of a combined medical and research centre able to provide the most cutting-edge technologies in medical imaging and cancer radiation therapy. The cyclotron is complemented by the RFQ with the primary goals of elemental analysis via Particle Induced Gamma Emission (PIGE), and the detection of potentially dangerous materials with high nitrogen content using the Gamma-Resonant Nuclear Absorption (GRNA) technique. In this context, beam instrumentation devices have been developed, in particular an innovative beam profile monitor based on doped silica fibres and a setup for emittance measurements using the pepper-pot technique. On this basis, the establishment of a proton therapy centre on the campus of the Inselspital is in the phase of advanced study

  12. The cyclotron laboratory and the RFQ accelerator in Bern

    Energy Technology Data Exchange (ETDEWEB)

    Braccini, S.; Ereditato, A.; Kreslo, I.; Nirkko, M.; Weber, M. [Albert Einstein Center for Fundamental Physics, Laboratory for High Energy Physics (LHEP), University of Bern, Sidlerstrasse 5, CH-3012 Bern (Switzerland); Scampoli, P. [Albert Einstein Center for Fundamental Physics, Laboratory for High Energy Physics (LHEP), University of Bern, Sidlerstrasse 5, CH-3012 Bern, Switzerland and Department of Physical Sciences, University Federico II, Via Cintia, I-60126 Napoli (Italy); Bremen, K. von [SWAN Isotopen AG, Inselspital, CH-3010 Bern (Switzerland)

    2013-07-18

    Two proton accelerators have been recently put in operation in Bern: an 18 MeV cyclotron and a 2 MeV RFQ linac. The commercial IBA 18/18 cyclotron, equipped with a specifically conceived 6 m long external beam line ending in a separate bunker, will provide beams for routine 18-F and other PET radioisotope production as well as for novel detector, radiation biophysics, radioprotection, radiochemistry and radiopharmacy developments. The accelerator is embedded into a complex building hosting two physics laboratories and four Good Manufacturing Practice (GMP) laboratories. This project is the result of a successful collaboration between the Inselspital, the University of Bern and private investors, aiming at the constitution of a combined medical and research centre able to provide the most cutting-edge technologies in medical imaging and cancer radiation therapy. The cyclotron is complemented by the RFQ with the primary goals of elemental analysis via Particle Induced Gamma Emission (PIGE), and the detection of potentially dangerous materials with high nitrogen content using the Gamma-Resonant Nuclear Absorption (GRNA) technique. In this context, beam instrumentation devices have been developed, in particular an innovative beam profile monitor based on doped silica fibres and a setup for emittance measurements using the pepper-pot technique. On this basis, the establishment of a proton therapy centre on the campus of the Inselspital is in the phase of advanced study.

  13. Nuclear and radiochemistry research: from development to deployment

    International Nuclear Information System (INIS)

    Tomar, B.S.

    2015-01-01

    Fundamental research in nuclear and radiochemistry is essential in building the expertise in quality assurance and quality control (QA/QC) of nuclear materials, which in turn is important for harnessing nuclear energy for peaceful purposes. Expansion of nuclear fuel cycle activities throws several new challenges before the nuclear scientists with regard to the chemical quality control, quality assurance, accounting of special nuclear materials, improving the detection limits of the trace elements, etc. Nondestructive assay (NDA) of nuclear materials is important from the point of view of nuclear material accounting and control. The requirement of QA/QC of finished products as well as accounting of special nuclear materials in waste packets can be met through NDA techniques. For this purpose passive gamma and neutron based techniques are employed for Pu based materials. On the other hand, NDA of uranium based fuels need active interrogation methods for quantitative assay in sealed packets, while isotopic composition can be measured using high resolution gamma ray spectrometry in suitable gamma energy region. Some of the other elements, such as, boron in finished products can be assayed using ion beam analysis techniques, such as proton induced gamma emission (PIGE) employing low energy proton beams. In the present talk, a few examples of such challenges and their possible solutions would be discussed. (author)

  14. Comprehensive urban air quality studies of Islamabad: elemental characterization of PM10 and PM2.5, source apportionment and transboundary pollutant migration (abstract)

    International Nuclear Information System (INIS)

    Waheed, S.; Siddique, N.; Daud, M.

    2011-01-01

    Long term urban air quality of Islamabad, the capital city of Pakistan, has been investigated as a part of the joint UNDP/IAEA/RCA/RAS/7/015 project, entitled C haracterization and source identification of particulate air pollution in the Asian region (RCA) . Around 380 pairs of fine (PM2.5) and coarse (PM10-2.5) polycarbonate filters from the Nilore area were collected using GENT sampler. The average PM2.5 and PM2.5-10 masses at this site were found to be 15.02 and 37.01 g/m/sup 3/ respectively that are far below to the Pakistani limit for PM10 of 100 g/m/sup 3/. The average Black Carbon (BC) was found to be 2.58 and 1.22 g/m/sup 3/ corresponding to 20.7% and 4.54% of the fine and coarse mass respectively. The non destructive Ion Beam Analysis method, Proton induced X-ray emission (PIXE) and Proton induced gamma ray emission (PIGE) were employed to quantify more than 40 elements in both fine and coarse fractions. The acquired elemental data has been statistically treated and subjected to mass closure studies, principal component and factor analysis to calculate correlation matrices. The reconstructed mass (RCM) was calculated for both particle modes using soil, sulphate, smoke, sea salt and BC as pseudo sources. Data analysis performed using EPA-PMF3 shows that the fine and coarse data for the suburban site identifies 4 sources; biomass/ combustion, road dust, soil and automobile. Long range transport of pollutants was studied using HYSPLIT4 model. It was observed that high fine soil contributions in this area were mainly from dust storms arriving from west and North West of the country. (author)

  15. Elemental compositions of PM{sub 10–2.5} and PM{sub 2.5} aerosols of a Nigerian urban city using ion beam analytical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Ezeh, G.C., E-mail: goddyich@yahoo.com [Atmospheric Research and Information Analysis Laboratory (ARIAL), Centre for Energy Research and Development (CERD), Obafemi Awolowo University, Ile-Ife (Nigeria); Obioh, I.B. [Atmospheric Research and Information Analysis Laboratory (ARIAL), Centre for Energy Research and Development (CERD), Obafemi Awolowo University, Ile-Ife (Nigeria); Asubiojo, O.I. [Department of Chemistry, Obafemi Awolowo University, Ile-Ife (Nigeria); Chiari, M.; Nava, S.; Calzolai, G.; Lucarelli, F. [Department of Physics and Astronomy, University of Firenze and I.N.F.N., Via Sansone 1, 50029 Sesto Fiorentino (Italy); Nuviadenu, C.K. [Accelerator Research Centre, Ghana Atomic Energy Agency, Accra (Ghana)

    2014-09-01

    The paucity of data on air quality studies in Nigeria prompted us to commence the sampling of particulate matter (PM{sub 10–2.5} and PM{sub 2.5}) in Mushin Lagos, Nigeria. Both size-segregated fractions were collected using a double staged ‘Gent’ stack filter unit sampler. Elemental characterization was carried out by Particle Induced X-ray Emission (PIXE) and Proton Induced γ-ray Emission (PIGE) techniques using an external ion beam set-up. Twenty-four elements (Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Se, Br, Rb, Sr, Zr, Cs and Pb) were detected in both fractions and their concentrations were assessed. A study of their inter-elemental correlations indicated that some elements could have common source origins or similar chemical properties while enrichment factors (EF) displayed that most elements emanated from anthropogenic sources. Source apportionment studies are thus recommended.

  16. Neuromyelitis optica med udtalte cerebrale magnetisk resonans-skannings-forandringer hos en niårig pige

    DEFF Research Database (Denmark)

    Trautner, Simon; Pedersen, Hans Peder; Bendtson, Inger

    2009-01-01

    Neuromyelitis optica (NMO) is a rare inflammatory disorder characterised by optic neuritis and transverse myelitis. We report a severe pediatric case presenting with impaired vision, tetraparesis, bladder retention and lower extremity pain. Magnetic resonance imaging demonstrated longitudinally...

  17. PIXE, PIGE and NMR study of the masonry of the pyramid of Cheops at Giza

    International Nuclear Information System (INIS)

    Demortier, Guy

    2004-01-01

    The mystery of the construction of the great pyramids of Egypt could be elucidated by physico-chemical measurements on small pieces of the material. In this paper, we give several arguments against the present point of view of most Egyptologists who do not admit another method than hewn blocks. We give several pieces of evidence that the masonry was entirely built by a moulding procedure involving the use of ingredients that were all available in the region of Cairo

  18. PIXE, PIGE and NMR study of the masonry of the pyramid of Cheops at Giza

    Science.gov (United States)

    Demortier, Guy

    2004-11-01

    The mystery of the construction of the great pyramids of Egypt could be elucidated by physico-chemical measurements on small pieces of the material. In this paper, we give several arguments against the present point of view of most Egyptologists who do not admit another method than hewn blocks. We give several pieces of evidence that the masonry was entirely built by a moulding procedure involving the use of ingredients that were all available in the region of Cairo.

  19. Bio-monitoring studies using nuclear and related techniques for the study of air pollution in and around the city of Hyderabad, India

    International Nuclear Information System (INIS)

    Arunachalam, J.; Balaramakrishna, M.V.; Karunasagar, D.; David, Christopher; Kumar, Sanjiv

    2001-01-01

    Passive bio-monitoring using different plant species affords a cost effective approach to studies on environmental trace element pollution. Lower plants like mosses and lichens have already been demonstrated to be effective bio monitors. As part of our participation in the IAEA's Co-ordinated Research Program on 'Validation and application of plants as bio-monitors of trace element atmospheric pollution analyzed by nuclear and related techniques', we have carried out studies on the use of a moss (Funaria hygrometrica) and a shrub (Lanatana Camera). About 35 sampling locations covering industrial zones, locations with heavy traffic, commercial and residential areas were identified. The samples have been analyzed using ICP-MS and PIGE to provide elemental concentrations on a number of the moss show physical trapping of fine particulate matter. The data are examined with a view to assess the use of these plants as bio-monitors of toxic trace elements. The moss, available only during the monsoon, shows, on a dry weight basis, much higher levels of concentrations for many elements, than the shrub (leaves). The concentration profiles in relation to the sampling locations suggest that metallic pollution can be easily discerned. The elemental data are examined using principle component analysis. While the qualitative identification of the metallic pollutants is easier with reference to the sampling locations, it would also require complimentary information using other techniques to provide a quantitative estimate of total environmental trace element burden. (author)

  20. Er konsum av melk og egg assosiert med risiko for kreft? Foreløpige resultater fra en prospektiv undersøkelse

    Directory of Open Access Journals (Sweden)

    Grethe Albrektsen

    2009-10-01

    Full Text Available  SAMMENDRAGSammenhenger mellom kreftinsidens og konsum av egg og melk er studert i en prospektiv undersøkelse avca. 50 000 personer i alderen 30-69 år. Kostholdsdataene ble samlet inn i forbindelse med andre runde avhjerte- og karundersøkelsene som ble gjennomført av Statens helseundersøkelser i Finnmark, Sogn ogFjordane og Oppland i perioden 1977-83. Gjennomsnittlig oppfølgingstid var 11,8 år. Omlag 2000 personerfikk en kreftdiagnose i løpet av oppfølgingsperioden. Insidensrate-ratioer er beregnet i en log-lineærPoissonregresjon basert på personår under risiko. Vi fant ingen sammenheng mellom total kreftinsidens ogkonsum av melk (glass pr. dag eller egg (antall pr. uke, men for spesifikke krefttyper observerte vi enkelteassosiasjoner. Det arbeides nå med mer detaljerte analyser og med internasjonal publisering av resultatene.Albrektsen G, Heuch I, Jacobsen BK, Kvåle G. Is milk and egg consumption associated with cancerrisk? Preliminary results from a prospective study. Nor J Epidemiol 1997; 7 (2: 205-208.ENGLISH SUMMARYAssociations between cancer incidence and consumption of milk and eggs were examined in a prospectivestudy of about 50,000 persons aged 30-69 years. The mean follow-up period was 11.8 years. About 2000persons were diagnosed with cancer during follow-up. Incidence rate ratios were calculated in a log-linearPoisson regression model of person-years at risk. No relations were found between overall cancer incidenceand consumption of milk (glasses per day or eggs (number per week, but some associations were observedfor specific sites. The analysis of the data is in progress and the results presented are preliminary.

  1. Co-ordinated research project on use of nuclear and related analytical techniques in studying human health impacts of toxic elements consumed through foodstuffs contaminated by industrial activities. Report on the first research co-ordination meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    The overall objective of the Co-ordinated research project is to provide a scientific basis for better assessment of selected pollutants in the food chain with a view to elucidating their impacts on human health and nutrition. Results of this study will enhance the existing body of knowledge and can be used to develop preventive strategies. Specific objectve: To determine the extent to which toxic element levels in food are affected by surrounding industrial activities and to assess potential human exposure from the consumption of such foodstuffs. EXPECTED RESEARCH OUTPUTS (RESULTS): Harmonized protocols and procedures for sampling and analyses; ? Compiled results for toxic element levels and their average daily dietary intake (ADDI) / dietary intake; Evaluated toxic element exposure levels based on biological indicators (where applicable); Publications of the study results in an IAEA TECDOC, and in peer-reviewed journals by participants. ACTION PLAN (ACTIVITIES) a. Core research activities: 1 Identification of the study areas and population groups. 2 Collection of information on food consumption patterns of the population groups under study (e.g. through questionnaires). 3 Development of harmonized protocols and validation of analytical methodologies in compliance with ISO/IEC 17025. 4 Collection and analysis of food samples, and estimation of the dietary intake. 5 Collection and analysis of biological indicators where applicable. 6 Evaluation of possible relationships between human exposures and biological indicators for the pollutants studied. 4b. Supplementary activities: ? Speciation studies of pollutants. ? Comparison of present and previous data on relevant parameters. ? Possible production and distribution of laboratory intercomparison samples. 7. Recommendations for nuclear analytical techniques ? Nuclear analytical technique (NAT) such as INAA, PIXE, PIGE, XRF should be the primary technique of analysis; Instrumental neutron activation analysis (INAA

  2. Akut abdomen som følge af torkveret adnexa uteri hos en tiårig pige

    DEFF Research Database (Denmark)

    Steinthorsdottir, Kristin Julia; Folmer, Lars; Bisgaard, Thue

    2014-01-01

    A ten-year-old girl presented with four days of lower abdominal pain. A diagnostic laparoscopy on the suspicion of acute appendicitis revealed left-sided adnexal torsion. The cyanotic ovary was detorsed and recovered. At three-month follow-up there were no clinical or ultrasonic signs of pathology...

  3. The new nuclear microprobe at Livermore

    International Nuclear Information System (INIS)

    Roberts, M.L.; Bench, G.S.; Heikkinen, D.W.; Morse, D.H.; Bach, P.R.; Pontau, A.E.

    1994-10-01

    Lawrence Livermore National Laboratory (LLNL) and Sandia National Laboratories/California have jointly constructed a new nuclear microprobe beamline. This beamline is located on the LLNL 10 MV tandem accelerator and can be used for multidisciplinary research using PIXE, PIGE, energy loss tomography, or IBS techniques. Distinctive features of the beamline include incorporation of magnet power supplies into the accelerator control system, computer controlled object and image slits, automated target positioning to sub-micron resolution, and video optics for beam positioning and observation. Mitigation of vibrations was accomplished with vibration isolators and a rigid beamline design while integral beamline shielding was used to shield from stray magnetic fields. Available detectors include a wavelength dispersive X-ray spectrometer, a High-Purity Germanium detector (HPGe), a Lithium-Drifted Silicon X-Ray detector (SiLi), and solid state surface barrier detectors. Along with beamline performance, results from recent measurements on determination of trace impurities in an International Thermonuclear Experimental Reactor (ITER) super conducting wire strand, determination of Ca/Sr ratios in seashells, and determination of minor and trace element concentrations in sperm cells are presented

  4. PIXE facility at Centro Atomico Bariloche

    Energy Technology Data Exchange (ETDEWEB)

    Limandri, S.; Rodriguez, L. [Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina); Olivares, C.; Bernardi, G. [Centro Atomico Bariloche, Comision Nacional de Energia Atomica, San Carlos de Bariloche, Rio Negro (Argentina); Suarez, S. [lnstituto Balseiro, Universidad Nacional de Cuyo, San Carlos de Bariloche, Rio Negro (Argentina)

    2013-07-01

    Full text: A Tandem accelerator, NEC Pelletron 5SDH, has been recently installed at Centro Atomico Bariloche, Argentina. This facility provides the local scientific community the opportunity to use nuclear techniques in different fields such as material science, environment (air, soil and food), biology, archaeology, etc.). The ion beam techniques available in our laboratory includes the ones commonly used in material analysis, i. e., PIXE (proton induced X-ray emission), RBS (Rutherford backscattering spectroscopy), PIGE (proton induced gamma ray emission), channeling and ERDA (elastic recall detection analysis). The line used for material analysis consists of a NEC-RC43 Endstation with setups and detectors for all the techniques above mentioned. This communication includes a description of the system facility and the main associated equipment, in particular that for PIXE measurements. In addition, we show some recent applications of PIXE to the study of archaeological ceramics, smokeless gun powders, and the experimental determination of the efficiency or our SDD detector. The detector efficiency was estimated for energies between 0.27 and 25 keV. The method applied is based on the comparison of X-ray characteristic intensities excited by 2-MeV protons in bulk samples with theoretical predictions. The results are compared with efficiency values obtained by the product of the window transmission and the detector quantum efficiency. Element constituents of black, white, brown and ocher pigments from Aguada Culture (600-900 before present) were studied. The results obtained are compared with measurements performed at the Laboratorio de Implantacao Ionica-UFRGS. This study is helpful to interpret the social, political economic and cultural contexts of pre-Inca societies and the interaction among different sites. Traces amounts present in seven smokeless gun powders commonly used in Argentina were determined. The powders were deposited on a carbon tape and the

  5. PIXE facility at Centro Atomico Bariloche

    International Nuclear Information System (INIS)

    Limandri, S.; Rodriguez, L.; Olivares, C.; Bernardi, G.; Suarez, S.

    2013-01-01

    Full text: A Tandem accelerator, NEC Pelletron 5SDH, has been recently installed at Centro Atomico Bariloche, Argentina. This facility provides the local scientific community the opportunity to use nuclear techniques in different fields such as material science, environment (air, soil and food), biology, archaeology, etc.). The ion beam techniques available in our laboratory includes the ones commonly used in material analysis, i. e., PIXE (proton induced X-ray emission), RBS (Rutherford backscattering spectroscopy), PIGE (proton induced gamma ray emission), channeling and ERDA (elastic recall detection analysis). The line used for material analysis consists of a NEC-RC43 Endstation with setups and detectors for all the techniques above mentioned. This communication includes a description of the system facility and the main associated equipment, in particular that for PIXE measurements. In addition, we show some recent applications of PIXE to the study of archaeological ceramics, smokeless gun powders, and the experimental determination of the efficiency or our SDD detector. The detector efficiency was estimated for energies between 0.27 and 25 keV. The method applied is based on the comparison of X-ray characteristic intensities excited by 2-MeV protons in bulk samples with theoretical predictions. The results are compared with efficiency values obtained by the product of the window transmission and the detector quantum efficiency. Element constituents of black, white, brown and ocher pigments from Aguada Culture (600-900 before present) were studied. The results obtained are compared with measurements performed at the Laboratorio de Implantacao Ionica-UFRGS. This study is helpful to interpret the social, political economic and cultural contexts of pre-Inca societies and the interaction among different sites. Traces amounts present in seven smokeless gun powders commonly used in Argentina were determined. The powders were deposited on a carbon tape and the

  6. Study of In distribution on GaInSb:Al crystals by ion beam techniques

    Energy Technology Data Exchange (ETDEWEB)

    Streicher, M., E-mail: smorgana@gmail.com [Pontifícia Universidade Católica do Rio Grande do Sul, Av. Ipiranga, 6681, Porto Alegre, RS (Brazil); Instituto de Plasmas e Fusão Nuclear (IPFN), Instituto Superior Técnico, Universidade de Lisboa, E.N. 10, 2695-066 Bobadela LRS (Portugal); Corregidor, V.; Catarino, N. [Instituto de Plasmas e Fusão Nuclear (IPFN), Instituto Superior Técnico, Universidade de Lisboa, E.N. 10, 2695-066 Bobadela LRS (Portugal); Alves, L.C. [Centro de Ciências e Tecnologias Nucleares (C2TN), Instituto Superior Técnico, Universidade de Lisboa, E.N. 10, 2695-066 Bobadela LRS (Portugal); Franco, N. [Instituto de Plasmas e Fusão Nuclear (IPFN), Instituto Superior Técnico, Universidade de Lisboa, E.N. 10, 2695-066 Bobadela LRS (Portugal); Fonseca, M. [Universidade Europeia, Laureate International Universities, 1500-210 Lisboa (Portugal); Laboratório de Instrumentação, Engenharia Biomédica e Física da Radiação (LIBPhys-UNL), Departamento de Física, FCT-UNL, 2829-516 Monte da Caparica (Portugal); and others

    2016-03-15

    III–V ternary alloys semiconductor materials, in particular Ga{sub 1−x}In{sub x}Sb, are ideal candidates for device substrates because of the possibility to define the lattice constant as a function of the third element, indium. Aluminum, an isoelectric dopant for Ga and In, increases the carrier mobility in GaSb crystals and has influence over the concentration of native defects by passivating and/or compensating them. To understand the influence of Al on the distribution of indium in ternary alloys of Ga{sub 0.8}In{sub 0.2}Sb, pure and doped ingots were obtained with approximately 10{sup 20} atoms/cm{sup 3} of Al using a vertical Bridgman system. Analysis by scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX), X-ray diffraction (XRD), particle induced X-ray emission (PIXE) and particle induced gamma ray emission (PIGE) were used to obtain information on the structure defects and chemical composition of the crystals. The doped ingots showed good structural homogeneity when compared with the undoped alloy, and they were free from cracks and micro cracks. All of the obtained ingots present precipitates, twins and grains with different concentrations of In. The small compositional variation observed in the doped ingots along the radial direction (measured by PIXE), may be related to the solid–liquid interface’s quasi-equilibrium behavior. Regarding to the growth direction, it was observed that the undoped ingots exhibit a higher segregation phenomenon of the third element than the doped ingots. The obtained results indicate that aluminum influences the indium distribution in the ingots, thus ternary ingots with more homogeneous composition can be obtained and consequently electrical properties improved.

  7. Fluorine level in some city water supplies of Bangladesh

    International Nuclear Information System (INIS)

    Hoque, A.K.M.F.; Abedin, M.J.; Rahman, M.M.; Mia, M. Y.; Tarafder, M.S.A.; Khaliquzzaman, M.; Hossain, M.D.; Khan, A.H.

    2003-01-01

    Nuclear reaction based Proton Induced Gamma Emission (PIGE) analytical method was employed for the quantitative measurement of fluorine in the city water supplies of the major cities of Bangladesh. 102 water samples collected from 14 city supplies were analyzed and these samples contain fluorine in the range of 0.03 to 1.10 mg/L with a mean of 0.33 ± 0.21 mg/L. It was also observed that except the samples of Barisal, Dinajpur and Rajshahi, all other water samples analyzed contain a much lower amount of fluorine than the maximum permissible value for Bangladesh in drinking water, which is 1 mg/L. The mean concentration of fluorine in the samples of Barisal, Dinajpur and Rajshahi are respectively 0.79±0.01, 0.71±0.13 and 0.92±0.18 mg/L. For the 55 samples of Dhaka city supply the mean fluorine concentration is 0.31±0.17 mg/L and that of 9 samples from Chittagong city supply is 0.19±0.10 mg/L, which is the lowest among the 14 city supply samples analyzed in this study

  8. Characterization of by-products from the Coolside process

    International Nuclear Information System (INIS)

    Wong, A.S.; Thomas, G.A.; Schram, W.H.; Givens, E.N.; Robertson, J.D.

    1993-01-01

    Coolside is a flexible dry flue gas desulfurization process for removal of SO 2 from coal fired power plants emissions. Hydrated lime is pneumatically injected dry into the power plant duct work on the cool side of the air preheater. The flue gas stream is then humidified to within about 20--30 F of adiabatic saturation by spraying atomized water. A critical component of the Coolside process is the addition of a promoter to the water spray to enhance SO 2 capture efficiency. In general, sodium based compounds have been found to be the most effective promoters, although chloride salts have also been shown to be effective if added during lime hydration. The Coolside technology was successfully demonstrated at the Ohio Edison Edgewater Plant as part of a US DOE supported US EPA demonstration program. The test lasted from July 1989 through February 1990 and had two primary goals. First, to achieve overall SO 2 reductions of 30%, 50%, and 70%. Second, to achieve reliable process operations at 20 and 25 F approach to adiabatic saturation. The demonstration was considered successful. The Coolside solids differ from other dry scrubber wastes in that the residual lime is hydrated and from other low temperature scrubbing wastes in that the sorbent activator, NaOH in this case, introduces significant quantities of sodium compounds in the waste. Sixty-five tons of the waste were collected during the demonstration runs in February 1990 in order to assess the environmental impact of the by-product through a series of field lysimeter and laboratory column leaching studies. In the first phase of this assessment, approximately 400 samples of the by-product material have been analyzed for the major, minor, and trace elements by the ultimate and proximate analysis, X-ray fluorescence, and PIXE/PIGE analysis. The results of these analyses and the unique chemistry of the Coolside solids as a function of processing variables is presented in this paper

  9. The origin of emeralds embedded in archaeological artefacts in Slovenia

    Directory of Open Access Journals (Sweden)

    Albina Kržič

    2013-06-01

    Full Text Available Roman gold jewellery, which was excavated in Ptuj (Poetovio and consists of a necklace, earrings and a braceletwith embedded emeralds, is part of the Slovenian archaeological artefacts collections. Crystallographic characteristics,inclusions, luminous phenomena and geological characteristics were determined in order to establish theorigin of the emeralds. Chemical composition of the emeralds was determined non-destructively using the methodsof proton-induced X-rays and gamma rays (PIXE/PIGE. The results were compared with reference emeraldsfrom Habachtal in Austria and with green beryls from the Ural Mts. Literature data for emeralds from Egypt andmodern-day Afghanistan area were used to interpret the results. Specifically, these sites were known for emeraldsbeing mined for jewellery in Roman times. It was assumed that emeralds from archaeological artefacts originatedfrom Habachtal in Austria, given that this site was the nearest to the place where found. But the emeralds fromthe necklace and earrings in fact came from Egyptian deposits. The origin of emeralds from the bracelet could nothave been determined absolutely reliably due to the lack of comparative materials; they may originate from a site inmodern-day Afghanistan or from Egypt, but certainly not from the same site as the previously mentioned emeraldsin the necklace and earrings.

  10. Proceedings of the International Conference on Applications of High Precision Atomic and Nuclear Methods

    International Nuclear Information System (INIS)

    Olariu, Agata; Stenstroem, Kristina; Hellborg, Ragnar

    2005-01-01

    This volume presents the Proceedings of the International Conference on Applications of High Precision Atomic and Nuclear Methods, held in Neptun, Romania from 2nd to 6th of September 2002. The conference was organized by The Center of Excellence of the European Commission: Inter-Disciplinary Research and Applications based on Nuclear and Atomic Physics (IDRANAP) from Horia Hulubei National Institute for Physics and Nuclear Engineering, IFIN-HH, Bucharest-Magurele, Romania. The meeting gathered 66 participants from 25 different laboratories in 11 countries, namely: Belgium, Bulgaria, France, Germany, Hungary, Poland, Portugal, Romania, Slovakia and Sweden. Non European delegate came from Japan. The topics covered by the conference were as follows: - Environment: air, water and soil pollution, pollution with heavy elements and with radioisotopes, bio-monitoring (10 papers); - Radionuclide metrology (10 papers); - Ion beam based techniques for characterization of materials surface, ERDA, PIXE, PIGE, computer simulations, materials modifications, wear, corrosion (10 papers) ; - Accelerator Mass Spectrometry and applications in environment, archaeology, and medicine (7 papers); - Application of neutron spectrometry in condensed matter (1 paper); - Advanced techniques, facilities and applications (11). Seventeen invited speakers covered through overview talks the main parts of these topics. The book contains the overview talks, oral contributions and poster contributions

  11. XRF Newsletter, No. 18, December 2009

    International Nuclear Information System (INIS)

    2009-12-01

    Considerable progress has been observed in recent years in the development and applications of micro-analytical techniques based on nuclear spectrometry. Major reasons for this include the possibility to use new excitation sources such as synchrotron radiation (SR) facilities, and low-power compact X ray tubes designed to offer optimum excitation geometry, combined with the availability of advanced new-generation thermoelectrically cooled semiconductor detectors and of miniaturized or large-scale X ray optics with improved performance (in particular for use with SR sources). Consequently, the quality of characterization of various materials has improved considerably not only in large- scale laboratory facilities (ion-beam and SR sources) but also with in-house experimental set-ups, and new applications have become possible in support of applied research, teaching and education in nuclear science and technology in a wide variety of fields. The following nuclear spectrometry (and related) techniques can be used for microanalysis: (i) X ray fluorescence (XRF), (ii) total reflection X ray fluorescence (TXRF) (iii) neutron activation analysis (NAA), (iv) ion beam analysis based on applications of low-energy particle accelerators (including particle X ray emission - PIXE, particle induced gamma ray emission - PIGE, Rutherford backscattering spectrometry - RBS), (v) extended X ray absorption fine structure spectroscopy (EXAFS) and X ray absorption near-edge spectroscopy (XANES), (vi) X ray fluorescence micro-tomography, (vii) scanning electron microscopy (SEM), etc. The techniques are usually used for elemental analysis, 2D and 3D microscopy imaging, and chemical speciation. The range of possible applications of micro-analytical techniques is very wide and covers, inter alia, the following fields: - Industrial applications including microelectronics, mineralogy, study of corrosion processes, measurement of coating thickness, study of catalytic materials, waste

  12. Differential cross sections measurement of {sup 31}P(p,pγ{sub 1}){sup 31}P reaction for PIGE applications

    Energy Technology Data Exchange (ETDEWEB)

    Jokar, A., E-mail: arezajokar@gmail.com; Kakuee, O.; Lamehi-Rachti, M.

    2016-09-15

    Differential cross sections of proton induced gamma-ray emission from the {sup 31}P(p,pγ{sub 1}){sup 31}P (E{sub γ} = 1266 keV) nuclear reaction were measured in the proton energy range of 1886–3007 keV at the laboratory angle of 90°. For these measurements a thin Zn{sub 3}P{sub 2} target evaporated onto a self-supporting C film was used. The gamma-rays and backscattered protons were detected simultaneously. An HPGe detector placed at an angle of 90° with respect to the beam direction was employed to collect gamma-rays while an ion implanted Si detector placed at a scattering angle of 165° was used to detect backscattered protons. Simultaneous collection of gamma-rays and RBS spectra is a great advantage of this approach which makes differential cross-section measurements independent on the collected beam charge. The obtained cross-sections were compared with the previously only measured data in the literature. The validity of the measured differential cross sections was verified through a thick target benchmarking experiment. The overall systematic uncertainty of cross section values was estimated to be better than ±9%.

  13. The ionoluminescence apparatus at the LABEC external microbeam facility

    International Nuclear Information System (INIS)

    Calusi, S.; Colombo, E.; Giuntini, L.; Giudice, A. Lo; Manfredotti, C.; Massi, M.; Pratesi, G.; Vittone, E.

    2008-01-01

    In this paper, we describe the main features of the ionoluminescence (IL) apparatus recently installed at the external scanning microbeam facility of the 3 MV Tandetron accelerator of the INFN LABEC Laboratory in Firenze. The peculiarity of this IL set-up resides in the fact that the light produced by the ion irradiation of the specimen is collected by a bifurcated optical fiber, so that photons are shunted both to a CCD spectrometer, working in the 200-900 nm wavelength range, and to a photomultiplier (PMT). The accurate focusing of the optical system allows high photon collection efficiency and this results in rapid acquisition of luminescence spectra with low ion currents on luminescent materials; simultaneously, luminescence maps with a spatial resolution of 10 μm can be acquired through the synchronization of PMT photon detection with the position of the scanning focused ion beam. An optical filter with a narrow passband facing the photomultiplier allows chromatic selectivity of the luminescence centres. The IL apparatus is synergistically integrated into the existing set-up for ion beam analyses (IBA). The upgraded system permits simultaneous IL and PIXE/PIGE/BS measurements. With our integrated system, we have been studying raw lapis lazuli samples of different known origins and precious lapis lazuli artworks of the Collezione Medicea of Museum of Natural History, University of Firenze, aiming at characterising their composition and provenance

  14. The ionoluminescence apparatus at the LABEC external microbeam facility

    Energy Technology Data Exchange (ETDEWEB)

    Calusi, S.; Colombo, E. [INFN Sezione di Torino, Via P.Giuria 1, 10125 Torino (Italy); Dipartimento di Fisica Sperimentale and NIS Excellence Centre, Universita di Torino, Via P. Giuria 1, 10125 Torino (Italy); Giuntini, L. [Dipartimento di Fisica, Universita and INFN Sezione di Firenze, Via Sansone 1, 50019, Sesto Fiorentino, Firenze (Italy)], E-mail: giuntini@fi.infn.it; Giudice, A. Lo [Dipartimento di Fisica Sperimentale and NIS Excellence Centre, Universita di Torino, Via P. Giuria 1, 10125 Torino (Italy); Manfredotti, C. [INFN Sezione di Torino, Via P.Giuria 1, 10125 Torino (Italy); Dipartimento di Fisica Sperimentale and NIS Excellence Centre, Universita di Torino, Via P. Giuria 1, 10125 Torino (Italy); Massi, M. [Dipartimento di Fisica, Universita and INFN Sezione di Firenze, Via Sansone 1, 50019, Sesto Fiorentino, Firenze (Italy); Pratesi, G. [Dipartimento di Scienze della Terra and Museo di Storia Naturale, Universita di Firenze, Via G. La Pira 4, 50121 Firenze (Italy); Vittone, E. [INFN Sezione di Torino, Via P.Giuria 1, 10125 Torino (Italy); Dipartimento di Fisica Sperimentale and NIS Excellence Centre, Universita di Torino, Via P. Giuria 1, 10125 Torino (Italy)

    2008-05-15

    In this paper, we describe the main features of the ionoluminescence (IL) apparatus recently installed at the external scanning microbeam facility of the 3 MV Tandetron accelerator of the INFN LABEC Laboratory in Firenze. The peculiarity of this IL set-up resides in the fact that the light produced by the ion irradiation of the specimen is collected by a bifurcated optical fiber, so that photons are shunted both to a CCD spectrometer, working in the 200-900 nm wavelength range, and to a photomultiplier (PMT). The accurate focusing of the optical system allows high photon collection efficiency and this results in rapid acquisition of luminescence spectra with low ion currents on luminescent materials; simultaneously, luminescence maps with a spatial resolution of 10 {mu}m can be acquired through the synchronization of PMT photon detection with the position of the scanning focused ion beam. An optical filter with a narrow passband facing the photomultiplier allows chromatic selectivity of the luminescence centres. The IL apparatus is synergistically integrated into the existing set-up for ion beam analyses (IBA). The upgraded system permits simultaneous IL and PIXE/PIGE/BS measurements. With our integrated system, we have been studying raw lapis lazuli samples of different known origins and precious lapis lazuli artworks of the Collezione Medicea of Museum of Natural History, University of Firenze, aiming at characterising their composition and provenance.

  15. Advances in elemental imaging of rocks using the AGLAE external microbeam

    Energy Technology Data Exchange (ETDEWEB)

    Calligaro, T., E-mail: thomas.calligaro@culture.gouv.fr [Centre de Recherche et de Restauration des musees de France, CNRS UMR171, Palais du Louvre, 75001 Paris (France); Coquinot, Y.; Pichon, L.; Moignard, B. [Centre de Recherche et de Restauration des musees de France, CNRS UMR171, Palais du Louvre, 75001 Paris (France)

    2011-10-15

    Rocks are widely represented in cultural heritage materials. They constitute the major part of archaeological artefacts like stone carvings, tools and weapons, and are present in art works in various forms, such as precious stone inlays or paint pigments. The study of such geomaterials, which are usually constituted of a complex aggregate of mineral phases, aims at determining their exact nature, their provenance and at understanding their possible alteration. Since minerals are often composed of light elements, IBA techniques such as PIXE and PIGE, thanks to their ability to measure with high sensitivity elements down to lithium, should be well adapted to their analysis. However, the bulk composition classically obtained using macro-IBA on pelletized samples or using a broad beam hides the multi-phased nature of the rocks and considerably blurs the searched chemical fingerprint. In contrast, the small size of a nuclear microprobe allows imaging the chemical composition at a finer scale and, when implemented in air, appears ideally suited to analyse without sampling these often precious items. This paper illustrates chemical micro-imaging of rocks with examples performed with the AGLAE external nuclear microprobe: characterisation of microscopic inclusions in gems and detailed chemical mapping of rocks with special emphasis to lapis lazuli. Lapis lazuli is of particular interest in both archaeology and art history: after being employed in Asia since the 7th millennium BC to make carvings and beads, it was used in Medieval Europe as a precious blue painting pigment known as ultramarine. The chemical imaging of major and trace elements in lapis lazuli using external {mu}-PIXE has permitted to identify its mineral phases, to assign their trace elements and to evidence undetected elements. In combination with {mu}-XRD and {mu}-Raman spectrometry, this approach provides a clear mineralogical fingerprint useful to determine rock provenance and to authenticate artefacts

  16. Advances in elemental imaging of rocks using the AGLAE external microbeam

    International Nuclear Information System (INIS)

    Calligaro, T.; Coquinot, Y.; Pichon, L.; Moignard, B.

    2011-01-01

    Rocks are widely represented in cultural heritage materials. They constitute the major part of archaeological artefacts like stone carvings, tools and weapons, and are present in art works in various forms, such as precious stone inlays or paint pigments. The study of such geomaterials, which are usually constituted of a complex aggregate of mineral phases, aims at determining their exact nature, their provenance and at understanding their possible alteration. Since minerals are often composed of light elements, IBA techniques such as PIXE and PIGE, thanks to their ability to measure with high sensitivity elements down to lithium, should be well adapted to their analysis. However, the bulk composition classically obtained using macro-IBA on pelletized samples or using a broad beam hides the multi-phased nature of the rocks and considerably blurs the searched chemical fingerprint. In contrast, the small size of a nuclear microprobe allows imaging the chemical composition at a finer scale and, when implemented in air, appears ideally suited to analyse without sampling these often precious items. This paper illustrates chemical micro-imaging of rocks with examples performed with the AGLAE external nuclear microprobe: characterisation of microscopic inclusions in gems and detailed chemical mapping of rocks with special emphasis to lapis lazuli. Lapis lazuli is of particular interest in both archaeology and art history: after being employed in Asia since the 7th millennium BC to make carvings and beads, it was used in Medieval Europe as a precious blue painting pigment known as ultramarine. The chemical imaging of major and trace elements in lapis lazuli using external μ-PIXE has permitted to identify its mineral phases, to assign their trace elements and to evidence undetected elements. In combination with μ-XRD and μ-Raman spectrometry, this approach provides a clear mineralogical fingerprint useful to determine rock provenance and to authenticate artefacts of

  17. Synchrotron and ion beam studies of the bone-cartilage interface

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, D.A., E-mail: d.a.bradley@surrey.ac.u [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Kaabar, W.; Gundogdu, O. [Department of Physics, University of Surrey, Guildford GU2 7XH (United Kingdom); Farquharson, M.J. [Department of Medical Physics and Applied Radiation Sciences, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4K1 (Canada); Janousch, M. [Swiss Light Source, Paul Scherrer Institute, 5232 Villigen (Switzerland); Bailey, M.; Jeynes, C. [Surrey Ion Beam Centre, University of Surrey, Guildford GU2 7XH (United Kingdom)

    2010-07-21

    The divalent cations Ca, P and Zn have been reported to play an important role in the normal growth and remodelling of articular cartilage and subchondral bone and in the degenerative and inflammatory processes associated with osteoarthritis (OA). In particular, they act as co-factors of a class of enzymes known as metalloproteinases, believed to be active during the initiation, progress and remodelling processes associated with the disease. The relative presence of cations and anions, in particular the ions Na{sup 2+} and Cl{sup -}, is also intimately associated with the fixed charge density (FCD) of cartilage, neutralizing the highly charged structure associated with for instance chondroitin sulphate. Finally, structural components of bone can be expected to result from dietary intake, yielding for instance strontium apatite and fluorapatite that form inclusions in the calcium hydroxyapatite of bone. In the present investigation, thin sections of articular cartilage affected by OA have been examined using a combination of physical techniques: low energy synchrotron micro X-ray fluorescence ({mu}-SXRF), micro proton induced X-ray emission ({mu}-PIXE) and micro proton-induced gamma emission ({mu}-PIGE), primarily to investigate the distribution of essential cations and anions. The combination of these physical techniques offers the ability to make comprehensive assessment of the elemental content of such tissues, simultaneous mappings of a range of relatively low atomic number ions being obtained over quite large areas ({approx}few mm{sup 2}). Such capability has only become a realistic prospect in recent times.

  18. Synchrotron and ion beam studies of the bone-cartilage interface

    International Nuclear Information System (INIS)

    Bradley, D.A.; Kaabar, W.; Gundogdu, O.; Farquharson, M.J.; Janousch, M.; Bailey, M.; Jeynes, C.

    2010-01-01

    The divalent cations Ca, P and Zn have been reported to play an important role in the normal growth and remodelling of articular cartilage and subchondral bone and in the degenerative and inflammatory processes associated with osteoarthritis (OA). In particular, they act as co-factors of a class of enzymes known as metalloproteinases, believed to be active during the initiation, progress and remodelling processes associated with the disease. The relative presence of cations and anions, in particular the ions Na 2+ and Cl - , is also intimately associated with the fixed charge density (FCD) of cartilage, neutralizing the highly charged structure associated with for instance chondroitin sulphate. Finally, structural components of bone can be expected to result from dietary intake, yielding for instance strontium apatite and fluorapatite that form inclusions in the calcium hydroxyapatite of bone. In the present investigation, thin sections of articular cartilage affected by OA have been examined using a combination of physical techniques: low energy synchrotron micro X-ray fluorescence (μ-SXRF), micro proton induced X-ray emission (μ-PIXE) and micro proton-induced gamma emission (μ-PIGE), primarily to investigate the distribution of essential cations and anions. The combination of these physical techniques offers the ability to make comprehensive assessment of the elemental content of such tissues, simultaneous mappings of a range of relatively low atomic number ions being obtained over quite large areas (∼few mm 2 ). Such capability has only become a realistic prospect in recent times.

  19. Decision analysis multicriteria analysis

    International Nuclear Information System (INIS)

    Lombard, J.

    1986-09-01

    The ALARA procedure covers a wide range of decisions from the simplest to the most complex one. For the simplest one the engineering judgement is generally enough and the use of a decision aiding technique is therefore not necessary. For some decisions the comparison of the available protection option may be performed from two or a few criteria (or attributes) (protection cost, collective dose,...) and the use of rather simple decision aiding techniques, like the Cost Effectiveness Analysis or the Cost Benefit Analysis, is quite enough. For the more complex decisions, involving numerous criteria or for decisions involving large uncertainties or qualitative judgement the use of these techniques, even the extended cost benefit analysis, is not recommended and appropriate techniques like multi-attribute decision aiding techniques are more relevant. There is a lot of such particular techniques and it is not possible to present all of them. Therefore only two broad categories of multi-attribute decision aiding techniques will be presented here: decision analysis and the outranking analysis

  20. Shape analysis in medical image analysis

    CERN Document Server

    Tavares, João

    2014-01-01

    This book contains thirteen contributions from invited experts of international recognition addressing important issues in shape analysis in medical image analysis, including techniques for image segmentation, registration, modelling and classification, and applications in biology, as well as in cardiac, brain, spine, chest, lung and clinical practice. This volume treats topics such as, anatomic and functional shape representation and matching; shape-based medical image segmentation; shape registration; statistical shape analysis; shape deformation; shape-based abnormity detection; shape tracking and longitudinal shape analysis; machine learning for shape modeling and analysis; shape-based computer-aided-diagnosis; shape-based medical navigation; benchmark and validation of shape representation, analysis and modeling algorithms. This work will be of interest to researchers, students, and manufacturers in the fields of artificial intelligence, bioengineering, biomechanics, computational mechanics, computationa...

  1. High power pulse electron beam modification and ion implantation of Hg{sub 1-x}Cd{sub x}Te crystals

    Energy Technology Data Exchange (ETDEWEB)

    Vojtsekhovskij, A V; Remnev, G E [Tomsk Polytechnic Univ. (Russian Federation). Nuclear Physics Inst.; Opekunov, M S; Kokhanenko, A P; Korotaev, A G; Denisov, Yu A; Oucherenko, D A [Tomsk State Univ. (Russian Federation). Dept. of Radiophysics

    1997-12-31

    Hg{sub 1-x}Cd{sub x}Te (MCT) samples (x = 0.21 - 0.22) were irradiated by pulse electron beams at doses of 10{sup 13} to 10{sup 17} cm{sup -2}. The electron beams possessed the following parameters: 500 keV electron energy (30-40 A/cm{sup 2} electron current density, 60-80 ns current pulse); 200 keV electron energy (8- 10 A/cm{sup 2} electron current density, 100-200 ns current pulse). The electric conductivity and recombination of modified samples were investigated by the Hall effect and photoconductivity methods. For the 200 keV electron energy beam irradiation, the n-type surface regions were obtained under threshold mechanisms of donor defect generation. For the 500 keV electron energy beam irradiation, the maximum value of charge carrier lifetimes occur in the p- to n-type conductivity conversion range for the initial p-type crystals due to the conductivity compensation. MCT samples (x = 0.21 - 0.22) were implanted with Al ions at doses of 10{sup 12}-10{sup 16} cm{sup -2}. The ion beams possessed the following parameters: (1-10) A/cm{sup 2} ion current density, (100-200) ns current pulse; (150-450) keV Al ion (Al{sup +},Al{sup ++}, Al{sup +++}). The ion distribution and doping profiles were investigated by PIGE and Hall effect methods. Comparison between MCT samples after power pulse ion implantation and after standard ion implantation demonstrates differences in ion distribution, doping profiles and defect formation radiation mechanisms. (author). 3 figs., 8 refs.

  2. Fluorine uptake into the human tooth from a thin layer of F-releasing material

    International Nuclear Information System (INIS)

    Yamamoto, H.; Nomachi, M.; Yasuda, K.; Iwami, Y.; Ebisu, S.; Komatsu, H.; Sakai, T.; Kamiya, T.

    2007-01-01

    Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 μm) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries

  3. Fluorine uptake into the human tooth from a thin layer of F-releasing material

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan)]. E-mail: yhiroko@dent.osaka-u.ac.jp; Nomachi, M. [Graduate School of Science, Osaka University, Toyonaka, Osaka, 560-0043 (Japan); Yasuda, K. [Wakasa Wan Energy Research Center, Tsuruga, Fukui, 914-0192 (Japan); Iwami, Y. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Ebisu, S. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Sapporo, Hokkaido, 060-8585 (Japan); Sakai, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan); Kamiya, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan)

    2007-07-15

    Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 {mu}m) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries.

  4. Theoretical numerical analysis a functional analysis framework

    CERN Document Server

    Atkinson, Kendall

    2005-01-01

    This textbook prepares graduate students for research in numerical analysis/computational mathematics by giving to them a mathematical framework embedded in functional analysis and focused on numerical analysis. This helps the student to move rapidly into a research program. The text covers basic results of functional analysis, approximation theory, Fourier analysis and wavelets, iteration methods for nonlinear equations, finite difference methods, Sobolev spaces and weak formulations of boundary value problems, finite element methods, elliptic variational inequalities and their numerical solu

  5. An example of multidimensional analysis: Discriminant analysis

    International Nuclear Information System (INIS)

    Lutz, P.

    1990-01-01

    Among the approaches on the data multi-dimensional analysis, lectures on the discriminant analysis including theoretical and practical aspects are presented. The discrimination problem, the analysis steps and the discrimination categories are stressed. Examples on the descriptive historical analysis, the discrimination for decision making, the demonstration and separation of the top quark are given. In the linear discriminant analysis the following subjects are discussed: Huyghens theorem, projection, discriminant variable, geometrical interpretation, case for g=2, classification method, separation of the top events. Criteria allowing the obtention of relevant results are included [fr

  6. Energy-Water Modeling and Analysis | Energy Analysis | NREL

    Science.gov (United States)

    Generation (ReEDS Model Analysis) U.S. Energy Sector Vulnerabilities to Climate Change and Extreme Weather Modeling and Analysis Energy-Water Modeling and Analysis NREL's energy-water modeling and analysis vulnerabilities from various factors, including water. Example Projects Renewable Electricity Futures Study

  7. Instrumental analysis

    International Nuclear Information System (INIS)

    Jae, Myeong Gi; Lee, Won Seong; Kim, Ha Hyeok

    1989-02-01

    This book give description of electronic engineering such as circuit element and device, circuit analysis and logic digital circuit, the method of electrochemistry like conductometry, potentiometry and current measuring, spectro chemical analysis with electromagnetic radiant rays, optical components, absorption spectroscopy, X-ray analysis, atomic absorption spectrometry and reference, chromatography like gas-chromatography and liquid-chromatography and automated analysis on control system evaluation of automated analysis and automated analysis system and reference.

  8. Instrumental analysis

    Energy Technology Data Exchange (ETDEWEB)

    Jae, Myeong Gi; Lee, Won Seong; Kim, Ha Hyeok

    1989-02-15

    This book give description of electronic engineering such as circuit element and device, circuit analysis and logic digital circuit, the method of electrochemistry like conductometry, potentiometry and current measuring, spectro chemical analysis with electromagnetic radiant rays, optical components, absorption spectroscopy, X-ray analysis, atomic absorption spectrometry and reference, chromatography like gas-chromatography and liquid-chromatography and automated analysis on control system evaluation of automated analysis and automated analysis system and reference.

  9. Analysis of Project Finance | Energy Analysis | NREL

    Science.gov (United States)

    Analysis of Project Finance Analysis of Project Finance NREL analysis helps potential renewable energy developers and investors gain insights into the complex world of project finance. Renewable energy project finance is complex, requiring knowledge of federal tax credits, state-level incentives, renewable

  10. Performance analysis

    International Nuclear Information System (INIS)

    2008-05-01

    This book introduces energy and resource technology development business with performance analysis, which has business division and definition, analysis of current situation of support, substance of basic plan of national energy, resource technique development, selection of analysis index, result of performance analysis by index, performance result of investigation, analysis and appraisal of energy and resource technology development business in 2007.

  11. Laboratory of ion beam applications at ATOMKI

    International Nuclear Information System (INIS)

    Borbely-Kiss, I.; Huszank, R.; Kertesz, Zs.; Kiss, A.Z.; Koltay, E.; Rajta, I.; Simon, A.; Szabo, Gy.; Szikszai, Z.; Szilasi, S.Z.; Szoboszlai, Z.; Uzonyi, I.

    2008-01-01

    Introduction. The Laboratory of Ion Beam Applications of ATOMKI is devoted to applications of atomic and nuclear physics in the fields of environmental research, biomedicine, geology, materials and surface science (including ion beam induced damage investigations and proton beam lithography) and cultural heritage research. We perform our work in the frame of various projects and collaborations: EU, IAEA, R and D, OTKA, etc. Our laboratory provides service for external (national and international) and internal users and contributes to higher education, as well. The Laboratory is based on the home-made 5 MV Van de Graaff (VdG) electrostatic accelerator of the institute. The accelerator was put into operation in 1971 and in the beginning it supplied ion beams exclusively for nuclear physics. A few years later with the measurements of K-shell ionization cross sections the door became open also for basic atomic physics. In parallel with this basic study, the application of proton induced X-ray emission (PIXE) for the elemental analysis of biological (hair, erythrocyte and blood plasma) samples and atmospheric aerosols also started. The first paper on PIXE, a methodological one, was published in 1978. The experience gained on these applications and later on archaeology led to the construction of complex PIXE chambers, which were sold, together with the corresponding know-how, to institutions in China, Portugal, Bangladesh, Jordan, North Korea, Singapore, Cuba and Mexico through the International Atomic Energy Agency (IAEA). For the evaluation of PIXE spectra the laboratory has been continuously developing its own computer programme package. The first version of this continuous development was published in 1988. In the meantime a second IBA analysis method, the proton induced gamma ray emission (PIGE), was introduced in the laboratory and was applied simultaneously with PIXE. Application of deuteron induced gamma ray emission (DIGE) started more than a decade later. A

  12. Trial Sequential Analysis in systematic reviews with meta-analysis

    Directory of Open Access Journals (Sweden)

    Jørn Wetterslev

    2017-03-01

    Full Text Available Abstract Background Most meta-analyses in systematic reviews, including Cochrane ones, do not have sufficient statistical power to detect or refute even large intervention effects. This is why a meta-analysis ought to be regarded as an interim analysis on its way towards a required information size. The results of the meta-analyses should relate the total number of randomised participants to the estimated required meta-analytic information size accounting for statistical diversity. When the number of participants and the corresponding number of trials in a meta-analysis are insufficient, the use of the traditional 95% confidence interval or the 5% statistical significance threshold will lead to too many false positive conclusions (type I errors and too many false negative conclusions (type II errors. Methods We developed a methodology for interpreting meta-analysis results, using generally accepted, valid evidence on how to adjust thresholds for significance in randomised clinical trials when the required sample size has not been reached. Results The Lan-DeMets trial sequential monitoring boundaries in Trial Sequential Analysis offer adjusted confidence intervals and restricted thresholds for statistical significance when the diversity-adjusted required information size and the corresponding number of required trials for the meta-analysis have not been reached. Trial Sequential Analysis provides a frequentistic approach to control both type I and type II errors. We define the required information size and the corresponding number of required trials in a meta-analysis and the diversity (D2 measure of heterogeneity. We explain the reasons for using Trial Sequential Analysis of meta-analysis when the actual information size fails to reach the required information size. We present examples drawn from traditional meta-analyses using unadjusted naïve 95% confidence intervals and 5% thresholds for statistical significance. Spurious conclusions in

  13. Instrumental analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seung Jae; Seo, Seong Gyu

    1995-03-15

    This textbook deals with instrumental analysis, which consists of nine chapters. It has Introduction of analysis chemistry, the process of analysis and types and form of the analysis, Electrochemistry on basic theory, potentiometry and conductometry, electromagnetic radiant rays and optical components on introduction and application, Ultraviolet rays and Visible spectrophotometry, Atomic absorption spectrophotometry on introduction, flame emission spectrometry and plasma emission spectrometry. The others like infrared spectrophotometry, X-rays spectrophotometry and mass spectrometry, chromatography and the other instrumental analysis like radiochemistry.

  14. Instrumental analysis

    International Nuclear Information System (INIS)

    Kim, Seung Jae; Seo, Seong Gyu

    1995-03-01

    This textbook deals with instrumental analysis, which consists of nine chapters. It has Introduction of analysis chemistry, the process of analysis and types and form of the analysis, Electrochemistry on basic theory, potentiometry and conductometry, electromagnetic radiant rays and optical components on introduction and application, Ultraviolet rays and Visible spectrophotometry, Atomic absorption spectrophotometry on introduction, flame emission spectrometry and plasma emission spectrometry. The others like infrared spectrophotometry, X-rays spectrophotometry and mass spectrometry, chromatography and the other instrumental analysis like radiochemistry.

  15. Functional analysis

    CERN Document Server

    Kantorovich, L V

    1982-01-01

    Functional Analysis examines trends in functional analysis as a mathematical discipline and the ever-increasing role played by its techniques in applications. The theory of topological vector spaces is emphasized, along with the applications of functional analysis to applied analysis. Some topics of functional analysis connected with applications to mathematical economics and control theory are also discussed. Comprised of 18 chapters, this book begins with an introduction to the elements of the theory of topological spaces, the theory of metric spaces, and the theory of abstract measure space

  16. Activation analysis in food analysis. Pt. 9

    International Nuclear Information System (INIS)

    Szabo, S.A.

    1992-01-01

    An overview is presented on the application of activation analysis (AA) techniques for food analysis, as reflected at a recent international conference titled Activation Analysis and its Applications. The most popular analytical techniques include instrumental neutron AA, (INAA or NAA), radiochemical NAA (RNAA), X-ray fluorescence analysis and mass spectrometry. Data are presented for the multielemental NAA of instant soups, for elemental composition of drinking water in Iraq, for Na, K, Mn contents of various Indian rices, for As, Hg, Sb and Se determination in various seafoods, for daily microelement takeup in China, for the elemental composition of Chinese teas. Expected development trends in AA are outlined. (R.P.) 24 refs.; 8 tabs

  17. Cross-impacts analysis development and energy policy analysis applications

    Energy Technology Data Exchange (ETDEWEB)

    Roop, J.M.; Scheer, R.M.; Stacey, G.S.

    1986-12-01

    Purpose of this report is to describe the cross-impact analysis process and microcomputer software developed for the Office of Policy, Planning, and Analysis (PPA) of DOE. First introduced in 1968, cross-impact analysis is a technique that produces scenarios of future conditions and possibilities. Cross-impact analysis has several unique attributes that make it a tool worth examining, especially in the current climate when the outlook for the economy and several of the key energy markets is uncertain. Cross-impact analysis complements the econometric, engineering, systems dynamics, or trend approaches already in use at DOE. Cross-impact analysis produces self-consistent scenarios in the broadest sense and can include interaction between the economy, technology, society and the environment. Energy policy analyses that couple broad scenarios of the future with detailed forecasting can produce more powerful results than scenario analysis or forecasts can produce alone.

  18. DTI analysis methods : Voxel-based analysis

    NARCIS (Netherlands)

    Van Hecke, Wim; Leemans, Alexander; Emsell, Louise

    2016-01-01

    Voxel-based analysis (VBA) of diffusion tensor imaging (DTI) data permits the investigation of voxel-wise differences or changes in DTI metrics in every voxel of a brain dataset. It is applied primarily in the exploratory analysis of hypothesized group-level alterations in DTI parameters, as it does

  19. Image analysis

    International Nuclear Information System (INIS)

    Berman, M.; Bischof, L.M.; Breen, E.J.; Peden, G.M.

    1994-01-01

    This paper provides an overview of modern image analysis techniques pertinent to materials science. The usual approach in image analysis contains two basic steps: first, the image is segmented into its constituent components (e.g. individual grains), and second, measurement and quantitative analysis are performed. Usually, the segmentation part of the process is the harder of the two. Consequently, much of the paper concentrates on this aspect, reviewing both fundamental segmentation tools (commonly found in commercial image analysis packages) and more advanced segmentation tools. There is also a review of the most widely used quantitative analysis methods for measuring the size, shape and spatial arrangements of objects. Many of the segmentation and analysis methods are demonstrated using complex real-world examples. Finally, there is a discussion of hardware and software issues. 42 refs., 17 figs

  20. Common pitfalls in statistical analysis: Linear regression analysis

    Directory of Open Access Journals (Sweden)

    Rakesh Aggarwal

    2017-01-01

    Full Text Available In a previous article in this series, we explained correlation analysis which describes the strength of relationship between two continuous variables. In this article, we deal with linear regression analysis which predicts the value of one continuous variable from another. We also discuss the assumptions and pitfalls associated with this analysis.

  1. CSF analysis

    Science.gov (United States)

    Cerebrospinal fluid analysis ... Analysis of CSF can help detect certain conditions and diseases. All of the following can be, but ... An abnormal CSF analysis result may be due to many different causes, ... Encephalitis (such as West Nile and Eastern Equine) Hepatic ...

  2. Semen analysis

    Science.gov (United States)

    ... analysis URL of this page: //medlineplus.gov/ency/article/003627.htm Semen analysis To use the sharing features on this page, please enable JavaScript. Semen analysis measures the amount and quality of a man's semen and sperm. Semen is ...

  3. Models of Economic Analysis

    OpenAIRE

    Adrian Ioana; Tiberiu Socaciu

    2013-01-01

    The article presents specific aspects of management and models for economic analysis. Thus, we present the main types of economic analysis: statistical analysis, dynamic analysis, static analysis, mathematical analysis, psychological analysis. Also we present the main object of the analysis: the technological activity analysis of a company, the analysis of the production costs, the economic activity analysis of a company, the analysis of equipment, the analysis of labor productivity, the anal...

  4. Limestone rocks analysis by X-ray fluorescence analysis

    International Nuclear Information System (INIS)

    Izquierdo M, G.; Ponce R, R.; Vazquez J, J.

    1996-01-01

    By request of a private company, employing basically X-ray fluorescence analysis (X RF), was established a fast and accurate method for the analysis of the major elements in limestone rocks. Additionally, for complementing analysis was determined by ion chromatography, the chlorides appearance and by atomic absorption of sodium. By gravimetry, was determined the losses by ignition and the alpha quartz. (Author)

  5. Sensitivity analysis and related analysis : A survey of statistical techniques

    NARCIS (Netherlands)

    Kleijnen, J.P.C.

    1995-01-01

    This paper reviews the state of the art in five related types of analysis, namely (i) sensitivity or what-if analysis, (ii) uncertainty or risk analysis, (iii) screening, (iv) validation, and (v) optimization. The main question is: when should which type of analysis be applied; which statistical

  6. Emergy-Based Regional Socio-Economic Metabolism Analysis: An Application of Data Envelopment Analysis and Decomposition Analysis

    OpenAIRE

    Zilong Zhang; Xingpeng Chen; Peter Heck

    2014-01-01

    Integrated analysis on socio-economic metabolism could provide a basis for understanding and optimizing regional sustainability. The paper conducted socio-economic metabolism analysis by means of the emergy accounting method coupled with data envelopment analysis and decomposition analysis techniques to assess the sustainability of Qingyang city and its eight sub-region system, as well as to identify the major driving factors of performance change during 2000–2007, to serve as the basis for f...

  7. failure analysis of a uav flight control system using markov analysis

    African Journals Online (AJOL)

    eobe

    2016-01-01

    Jan 1, 2016 ... Tree Analysis (FTA), Dependence Diagram Analysis. (DDA) and Markov Analysis (MA) are the most widely-used methods of probabilistic safety and reliability analysis for airborne system [1]. Fault trees analysis is a backward failure searching ..... [4] Christopher Dabrowski and Fern Hunt Markov Chain.

  8. Incidents analysis

    International Nuclear Information System (INIS)

    Francois, P.

    1996-01-01

    We undertook a study programme at the end of 1991. To start with, we performed some exploratory studies aimed at learning some preliminary lessons on this type of analysis: Assessment of the interest of probabilistic incident analysis; possibility of using PSA scenarios; skills and resources required. At the same time, EPN created a working group whose assignment was to define a new approach for analysis of incidents on NPPs. This working group gave thought to both aspects of Operating Feedback that EPN wished to improve: Analysis of significant incidents; analysis of potential consequences. We took part in the work of this group, and for the second aspects, we proposed a method based on an adaptation of the event-tree method in order to establish a link between existing PSA models and actual incidents. Since PSA provides an exhaustive database of accident scenarios applicable to the two most common types of units in France, they are obviously of interest for this sort of analysis. With this method we performed some incident analyses, and at the same time explores some methods employed abroad, particularly ASP (Accident Sequence Precursor, a method used by the NRC). Early in 1994 EDF began a systematic analysis programme. The first, transient phase will set up methods and an organizational structure. 7 figs

  9. Incidents analysis

    Energy Technology Data Exchange (ETDEWEB)

    Francois, P

    1997-12-31

    We undertook a study programme at the end of 1991. To start with, we performed some exploratory studies aimed at learning some preliminary lessons on this type of analysis: Assessment of the interest of probabilistic incident analysis; possibility of using PSA scenarios; skills and resources required. At the same time, EPN created a working group whose assignment was to define a new approach for analysis of incidents on NPPs. This working group gave thought to both aspects of Operating Feedback that EPN wished to improve: Analysis of significant incidents; analysis of potential consequences. We took part in the work of this group, and for the second aspects, we proposed a method based on an adaptation of the event-tree method in order to establish a link between existing PSA models and actual incidents. Since PSA provides an exhaustive database of accident scenarios applicable to the two most common types of units in France, they are obviously of interest for this sort of analysis. With this method we performed some incident analyses, and at the same time explores some methods employed abroad, particularly ASP (Accident Sequence Precursor, a method used by the NRC). Early in 1994 EDF began a systematic analysis programme. The first, transient phase will set up methods and an organizational structure. 7 figs.

  10. RELIABILITY ANALYSIS OF BENDING ELIABILITY ANALYSIS OF ...

    African Journals Online (AJOL)

    eobe

    Reliability analysis of the safety levels of the criteria slabs, have been .... was also noted [2] that if the risk level or β < 3.1), the ... reliability analysis. A study [6] has shown that all geometric variables, ..... Germany, 1988. 12. Hasofer, A. M and ...

  11. Safety analysis fundamentals

    International Nuclear Information System (INIS)

    Wright, A.C.D.

    2002-01-01

    This paper discusses the safety analysis fundamentals in reactor design. This study includes safety analysis done to show consequences of postulated accidents are acceptable. Safety analysis is also used to set design of special safety systems and includes design assist analysis to support conceptual design. safety analysis is necessary for licensing a reactor, to maintain an operating license, support changes in plant operations

  12. Visual physics analysis-from desktop to physics analysis at your fingertips

    International Nuclear Information System (INIS)

    Bretz, H-P; Erdmann, M; Fischer, R; Hinzmann, A; Klingebiel, D; Komm, M; Lingemann, J; Rieger, M; Müller, G; Steggemann, J; Winchen, T

    2012-01-01

    Visual Physics Analysis (VISPA) is an analysis environment with applications in high energy and astroparticle physics. Based on a data-flow-driven paradigm, it allows users to combine graphical steering with self-written C++ and Python modules. This contribution presents new concepts integrated in VISPA: layers, convenient analysis execution, and web-based physics analysis. While the convenient execution offers full flexibility to vary settings for the execution phase of an analysis, layers allow to create different views of the analysis already during its design phase. Thus, one application of layers is to define different stages of an analysis (e.g. event selection and statistical analysis). However, there are other use cases such as to independently optimize settings for different types of input data in order to guide all data through the same analysis flow. The new execution feature makes job submission to local clusters as well as the LHC Computing Grid possible directly from VISPA. Web-based physics analysis is realized in the VISPA-Web project, which represents a whole new way to design and execute analyses via a standard web browser.

  13. Experimental modal analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ibsen, Lars Bo; Liingaard, M.

    2006-12-15

    This technical report concerns the basic theory and principles for experimental modal analysis. The sections within the report are: Output-only modal analysis software, general digital analysis, basics of structural dynamics and modal analysis and system identification. (au)

  14. Analysis of Precision of Activation Analysis Method

    DEFF Research Database (Denmark)

    Heydorn, Kaj; Nørgaard, K.

    1973-01-01

    The precision of an activation-analysis method prescribes the estimation of the precision of a single analytical result. The adequacy of these estimates to account for the observed variation between duplicate results from the analysis of different samples and materials, is tested by the statistic T...

  15. Urban energy consumption: Different insights from energy flow analysis, input–output analysis and ecological network analysis

    International Nuclear Information System (INIS)

    Chen, Shaoqing; Chen, Bin

    2015-01-01

    Highlights: • Urban energy consumption was assessed from three different perspectives. • A new concept called controlled energy was developed from network analysis. • Embodied energy and controlled energy consumption of Beijing were compared. • The integration of all three perspectives will elucidate sustainable energy use. - Abstract: Energy consumption has always been a central issue for sustainable urban assessment and planning. Different forms of energy analysis can provide various insights for energy policy making. This paper brought together three approaches for energy consumption accounting, i.e., energy flow analysis (EFA), input–output analysis (IOA) and ecological network analysis (ENA), and compared their different perspectives and the policy implications for urban energy use. Beijing was used to exemplify the different energy analysis processes, and the 42 economic sectors of the city were aggregated into seven components. It was determined that EFA quantifies both the primary and final energy consumption of the urban components by tracking the different types of fuel used by the urban economy. IOA accounts for the embodied energy consumption (direct and indirect) used to produce goods and services in the city, whereas the control analysis of ENA quantifies the specific embodied energy that is regulated by the activities within the city’s boundary. The network control analysis can also be applied to determining which economic sectors drive the energy consumption and to what extent these sectors are dependent on each other for energy. So-called “controlled energy” is a new concept that adds to the analysis of urban energy consumption, indicating the adjustable energy consumed by sectors. The integration of insights from all three accounting perspectives further our understanding of sustainable energy use in cities

  16. CADDIS Volume 4. Data Analysis: Exploratory Data Analysis

    Science.gov (United States)

    Intro to exploratory data analysis. Overview of variable distributions, scatter plots, correlation analysis, GIS datasets. Use of conditional probability to examine stressor levels and impairment. Exploring correlations among multiple stressors.

  17. Social network analysis applied to team sports analysis

    CERN Document Server

    Clemente, Filipe Manuel; Mendes, Rui Sousa

    2016-01-01

    Explaining how graph theory and social network analysis can be applied to team sports analysis, This book presents useful approaches, models and methods that can be used to characterise the overall properties of team networks and identify the prominence of each team player. Exploring the different possible network metrics that can be utilised in sports analysis, their possible applications and variances from situation to situation, the respective chapters present an array of illustrative case studies. Identifying the general concepts of social network analysis and network centrality metrics, readers are shown how to generate a methodological protocol for data collection. As such, the book provides a valuable resource for students of the sport sciences, sports engineering, applied computation and the social sciences.

  18. Qualitative Content Analysis

    OpenAIRE

    Philipp Mayring

    2000-01-01

    The article describes an approach of systematic, rule guided qualitative text analysis, which tries to preserve some methodological strengths of quantitative content analysis and widen them to a concept of qualitative procedure. First the development of content analysis is delineated and the basic principles are explained (units of analysis, step models, working with categories, validity and reliability). Then the central procedures of qualitative content analysis, inductive development of ca...

  19. Quantitative analysis chemistry

    International Nuclear Information System (INIS)

    Ko, Wansuk; Lee, Choongyoung; Jun, Kwangsik; Hwang, Taeksung

    1995-02-01

    This book is about quantitative analysis chemistry. It is divided into ten chapters, which deal with the basic conception of material with the meaning of analysis chemistry and SI units, chemical equilibrium, basic preparation for quantitative analysis, introduction of volumetric analysis, acid-base titration of outline and experiment examples, chelate titration, oxidation-reduction titration with introduction, titration curve, and diazotization titration, precipitation titration, electrometric titration and quantitative analysis.

  20. Information security risk analysis

    CERN Document Server

    Peltier, Thomas R

    2001-01-01

    Effective Risk AnalysisQualitative Risk AnalysisValue AnalysisOther Qualitative MethodsFacilitated Risk Analysis Process (FRAP)Other Uses of Qualitative Risk AnalysisCase StudyAppendix A: QuestionnaireAppendix B: Facilitated Risk Analysis Process FormsAppendix C: Business Impact Analysis FormsAppendix D: Sample of ReportAppendix E: Threat DefinitionsAppendix F: Other Risk Analysis OpinionsIndex

  1. Standardizing Activation Analysis: New Software for Photon Activation Analysis

    Science.gov (United States)

    Sun, Z. J.; Wells, D.; Segebade, C.; Green, J.

    2011-06-01

    Photon Activation Analysis (PAA) of environmental, archaeological and industrial samples requires extensive data analysis that is susceptible to error. For the purpose of saving time, manpower and minimizing error, a computer program was designed, built and implemented using SQL, Access 2007 and asp.net technology to automate this process. Based on the peak information of the spectrum and assisted by its PAA library, the program automatically identifies elements in the samples and calculates their concentrations and respective uncertainties. The software also could be operated in browser/server mode, which gives the possibility to use it anywhere the internet is accessible. By switching the nuclide library and the related formula behind, the new software can be easily expanded to neutron activation analysis (NAA), charged particle activation analysis (CPAA) or proton-induced X-ray emission (PIXE). Implementation of this would standardize the analysis of nuclear activation data. Results from this software were compared to standard PAA analysis with excellent agreement. With minimum input from the user, the software has proven to be fast, user-friendly and reliable.

  2. Standardizing Activation Analysis: New Software for Photon Activation Analysis

    International Nuclear Information System (INIS)

    Sun, Z. J.; Wells, D.; Green, J.; Segebade, C.

    2011-01-01

    Photon Activation Analysis (PAA) of environmental, archaeological and industrial samples requires extensive data analysis that is susceptible to error. For the purpose of saving time, manpower and minimizing error, a computer program was designed, built and implemented using SQL, Access 2007 and asp.net technology to automate this process. Based on the peak information of the spectrum and assisted by its PAA library, the program automatically identifies elements in the samples and calculates their concentrations and respective uncertainties. The software also could be operated in browser/server mode, which gives the possibility to use it anywhere the internet is accessible. By switching the nuclide library and the related formula behind, the new software can be easily expanded to neutron activation analysis (NAA), charged particle activation analysis (CPAA) or proton-induced X-ray emission (PIXE). Implementation of this would standardize the analysis of nuclear activation data. Results from this software were compared to standard PAA analysis with excellent agreement. With minimum input from the user, the software has proven to be fast, user-friendly and reliable.

  3. Radioactivation analysis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1959-07-15

    Radioactivation analysis is the technique of radioactivation analysis of the constituents of a very small sample of matter by making the sample artificially radioactive. The first stage is to make the sample radioactive by artificial means, e.g. subject it to neutron bombardment. Once the sample has been activated, or made radioactive, the next task is to analyze the radiations given off by the sample. This analysis would indicate the nature and quantities of the various elements present in the sample. The reason is that the radiation from a particular radioisotope. In 1959 a symposium on 'Radioactivation Analysis' was organized in Vienna by the IAEA and the Joint Commission on Applied Radioactivity (ICSU). It was pointed out that there are certain factors creating uncertainties and elaborated how to overcome them. Attention was drawn to the fact that radioactivation analysis had proven a powerful tool tackling fundamental problems in geo- and cosmochemistry, and a review was given of the recent work in this field. Because of its extreme sensitivity radioactivation analysis had been principally employed for trace detection and its most extensive use has been in control of semiconductors and very pure metals. An account of the experience gained in the USA was given, where radioactivation analysis was being used by many investigators in various scientific fields as a practical and useful tool for elemental analyses. Much of this work had been concerned with determining sub microgramme and microgramme concentration of many different elements in samples of biological materials, drugs, fertilizers, fine chemicals, foods, fuels, glass, ceramic materials, metals, minerals, paints, petroleum products, resinous materials, soils, toxicants, water and other materials. In addition to these studies, radioactivation analysis had been used by other investigators to determine isotopic ratios of the stable isotopes of some of the elements. Another paper dealt with radioactivation

  4. Radioactivation analysis

    International Nuclear Information System (INIS)

    1959-01-01

    Radioactivation analysis is the technique of radioactivation analysis of the constituents of a very small sample of matter by making the sample artificially radioactive. The first stage is to make the sample radioactive by artificial means, e.g. subject it to neutron bombardment. Once the sample has been activated, or made radioactive, the next task is to analyze the radiations given off by the sample. This analysis would indicate the nature and quantities of the various elements present in the sample. The reason is that the radiation from a particular radioisotope. In 1959 a symposium on 'Radioactivation Analysis' was organized in Vienna by the IAEA and the Joint Commission on Applied Radioactivity (ICSU). It was pointed out that there are certain factors creating uncertainties and elaborated how to overcome them. Attention was drawn to the fact that radioactivation analysis had proven a powerful tool tackling fundamental problems in geo- and cosmochemistry, and a review was given of the recent work in this field. Because of its extreme sensitivity radioactivation analysis had been principally employed for trace detection and its most extensive use has been in control of semiconductors and very pure metals. An account of the experience gained in the USA was given, where radioactivation analysis was being used by many investigators in various scientific fields as a practical and useful tool for elemental analyses. Much of this work had been concerned with determining sub microgramme and microgramme concentration of many different elements in samples of biological materials, drugs, fertilizers, fine chemicals, foods, fuels, glass, ceramic materials, metals, minerals, paints, petroleum products, resinous materials, soils, toxicants, water and other materials. In addition to these studies, radioactivation analysis had been used by other investigators to determine isotopic ratios of the stable isotopes of some of the elements. Another paper dealt with radioactivation

  5. Uranium Isotopic Analysis with the FRAM Isotopic Analysis Code

    International Nuclear Information System (INIS)

    Vo, D.T.; Sampson, T.E.

    1999-01-01

    FRAM is the acronym for Fixed-Energy Response-Function Analysis with Multiple efficiency. This software was developed at Los Alamos National Laboratory originally for plutonium isotopic analysis. Later, it was adapted for uranium isotopic analysis in addition to plutonium. It is a code based on a self-calibration using several gamma-ray peaks for determining the isotopic ratios. The versatile-parameter database structure governs all facets of the data analysis. User editing of the parameter sets allows great flexibility in handling data with different isotopic distributions, interfering isotopes, and different acquisition parameters such as energy calibration and detector type

  6. Real analysis a comprehensive course in analysis, part 1

    CERN Document Server

    Simon, Barry

    2015-01-01

    A Comprehensive Course in Analysis by Poincaré Prize winner Barry Simon is a five-volume set that can serve as a graduate-level analysis textbook with a lot of additional bonus information, including hundreds of problems and numerous notes that extend the text and provide important historical background. Depth and breadth of exposition make this set a valuable reference source for almost all areas of classical analysis. Part 1 is devoted to real analysis. From one point of view, it presents the infinitesimal calculus of the twentieth century with the ultimate integral calculus (measure theory)

  7. Text analysis methods, text analysis apparatuses, and articles of manufacture

    Science.gov (United States)

    Whitney, Paul D; Willse, Alan R; Lopresti, Charles A; White, Amanda M

    2014-10-28

    Text analysis methods, text analysis apparatuses, and articles of manufacture are described according to some aspects. In one aspect, a text analysis method includes accessing information indicative of data content of a collection of text comprising a plurality of different topics, using a computing device, analyzing the information indicative of the data content, and using results of the analysis, identifying a presence of a new topic in the collection of text.

  8. NCEP SST Analysis

    Science.gov (United States)

    Organization Search Go Search Polar Go MMAB SST Analysis Main page About MMAB Our Mission Our Personnel EMC Branches Global Climate & Weather Modeling Mesoscale Modeling Marine Modeling and Analysis Contact EMC (RTG_SST_HR) analysis For a regional map, click the desired area in the global SST analysis and anomaly maps

  9. Analysis of Heat Transfer

    International Nuclear Information System (INIS)

    2003-08-01

    This book deals with analysis of heat transfer which includes nonlinear analysis examples, radiation heat transfer, analysis of heat transfer in ANSYS, verification of analysis result, analysis of heat transfer of transition with automatic time stepping and open control, analysis of heat transfer using arrangement of ANSYS, resistance of thermal contact, coupled field analysis such as of thermal-structural interaction, cases of coupled field analysis, and phase change.

  10. Combining Conversation Analysis and Nexus Analysis to explore hospital practices

    DEFF Research Database (Denmark)

    Paasch, Bettina Sletten

    , ethnographic observations, interviews, photos and documents were obtained. Inspired by the analytical manoeuvre of zooming in and zooming out proposed by Nicolini (Nicolini, 2009; Nicolini, 2013) the present study uses Conversations Analysis (Sacks, Schegloff, & Jefferson, 1974) and Embodied Interaction...... of interaction. In the conducted interviews nurses report mobile work phones to disturb interactions with patients when they ring, however, analysing the recorded interactions with tools from Conversations Analysis and Embodied Interaction Analysis displays how nurses demonstrate sophisticated awareness...... interrelationships influencing it. The present study thus showcases how Conversation Analysis and Nexus Analysis can be combined to achieve a multi-layered perspective on interactions between nurses, patients and mobile work phones....

  11. http Log Analysis

    DEFF Research Database (Denmark)

    Bøving, Kristian Billeskov; Simonsen, Jesper

    2004-01-01

    This article documents how log analysis can inform qualitative studies concerning the usage of web-based information systems (WIS). No prior research has used http log files as data to study collaboration between multiple users in organisational settings. We investigate how to perform http log...... analysis; what http log analysis says about the nature of collaborative WIS use; and how results from http log analysis may support other data collection methods such as surveys, interviews, and observation. The analysis of log files initially lends itself to research designs, which serve to test...... hypotheses using a quantitative methodology. We show that http log analysis can also be valuable in qualitative research such as case studies. The results from http log analysis can be triangulated with other data sources and for example serve as a means of supporting the interpretation of interview data...

  12. Importance-performance analysis based SWOT analysis

    OpenAIRE

    Phadermrod, Boonyarat; Crowder, Richard M.; Wills, Gary B.

    2016-01-01

    SWOT analysis, a commonly used tool for strategic planning, is traditionally a form of brainstorming. Hence, it has been criticised that it is likely to hold subjective views of the individuals who participate in a brainstorming session and that SWOT factors are not prioritized by their significance thus it may result in an improper strategic action. While most studies of SWOT analysis have only focused on solving these shortcomings separately, this study offers an approach to diminish both s...

  13. Neutron activation analysis of high-purity iron in comparison with chemical analysis

    International Nuclear Information System (INIS)

    Kinomura, Atsushi; Horino, Yuji; Takaki, Seiichi; Abiko, Kenji

    2000-01-01

    Neutron activation analysis of iron samples of three different purity levels has been performed and compared with chemical analysis for 30 metallic and metalloid impurity elements. The concentration of As, Cl, Cu, Sb and V detected by neutron activation analysis was mostly in agreement with that obtained by chemical analysis. The sensitivity limits of neutron activation analysis of three kinds of iron samples were calculated and found to be reasonable compared with measured values or detection limits of chemical analysis; however, most of them were above the detection limits of chemical analysis. Graphite-shielded irradiation to suppress fast neutron reactions was effective for Mn analysis without decreasing sensitivity to the other impurity elements. (author)

  14. Sensitivity analysis for matched pair analysis of binary data: From worst case to average case analysis.

    Science.gov (United States)

    Hasegawa, Raiden; Small, Dylan

    2017-12-01

    In matched observational studies where treatment assignment is not randomized, sensitivity analysis helps investigators determine how sensitive their estimated treatment effect is to some unmeasured confounder. The standard approach calibrates the sensitivity analysis according to the worst case bias in a pair. This approach will result in a conservative sensitivity analysis if the worst case bias does not hold in every pair. In this paper, we show that for binary data, the standard approach can be calibrated in terms of the average bias in a pair rather than worst case bias. When the worst case bias and average bias differ, the average bias interpretation results in a less conservative sensitivity analysis and more power. In many studies, the average case calibration may also carry a more natural interpretation than the worst case calibration and may also allow researchers to incorporate additional data to establish an empirical basis with which to calibrate a sensitivity analysis. We illustrate this with a study of the effects of cellphone use on the incidence of automobile accidents. Finally, we extend the average case calibration to the sensitivity analysis of confidence intervals for attributable effects. © 2017, The International Biometric Society.

  15. HAZARD ANALYSIS SOFTWARE

    International Nuclear Information System (INIS)

    Sommer, S; Tinh Tran, T.

    2008-01-01

    Washington Safety Management Solutions, LLC developed web-based software to improve the efficiency and consistency of hazard identification and analysis, control selection and classification, and to standardize analysis reporting at Savannah River Site. In the new nuclear age, information technology provides methods to improve the efficiency of the documented safety analysis development process which includes hazard analysis activities. This software provides a web interface that interacts with a relational database to support analysis, record data, and to ensure reporting consistency. A team of subject matter experts participated in a series of meetings to review the associated processes and procedures for requirements and standard practices. Through these meetings, a set of software requirements were developed and compiled into a requirements traceability matrix from which software could be developed. The software was tested to ensure compliance with the requirements. Training was provided to the hazard analysis leads. Hazard analysis teams using the software have verified its operability. The software has been classified as NQA-1, Level D, as it supports the analysis team but does not perform the analysis. The software can be transported to other sites with alternate risk schemes. The software is being used to support the development of 14 hazard analyses. User responses have been positive with a number of suggestions for improvement which are being incorporated as time permits. The software has enforced a uniform implementation of the site procedures. The software has significantly improved the efficiency and standardization of the hazard analysis process

  16. Mathematical analysis fundamentals

    CERN Document Server

    Bashirov, Agamirza

    2014-01-01

    The author's goal is a rigorous presentation of the fundamentals of analysis, starting from elementary level and moving to the advanced coursework. The curriculum of all mathematics (pure or applied) and physics programs include a compulsory course in mathematical analysis. This book will serve as can serve a main textbook of such (one semester) courses. The book can also serve as additional reading for such courses as real analysis, functional analysis, harmonic analysis etc. For non-math major students requiring math beyond calculus, this is a more friendly approach than many math-centric o

  17. XML-based analysis interface for particle physics data analysis

    International Nuclear Information System (INIS)

    Hu Jifeng; Lu Xiaorui; Zhang Yangheng

    2011-01-01

    The letter emphasizes on an XML-based interface and its framework for particle physics data analysis. The interface uses a concise XML syntax to describe, in data analysis, the basic tasks: event-selection, kinematic fitting, particle identification, etc. and a basic processing logic: the next step goes on if and only if this step succeeds. The framework can perform an analysis without compiling by loading the XML-interface file, setting p in run-time and running dynamically. An analysis coding in XML instead of C++, easy-to-understood arid use, effectively reduces the work load, and enables users to carry out their analyses quickly. The framework has been developed on the BESⅢ offline software system (BOSS) with the object-oriented C++ programming. These functions, required by the regular tasks and the basic processing logic, are implemented with both standard modules or inherited from the modules in BOSS. The interface and its framework have been tested to perform physics analysis. (authors)

  18. Survival analysis using S analysis of time-to-event data

    CERN Document Server

    Tableman, Mara

    2003-01-01

    Survival Analysis Using S: Analysis of Time-to-Event Data is designed as a text for a one-semester or one-quarter course in survival analysis for upper-level or graduate students in statistics, biostatistics, and epidemiology. Prerequisites are a standard pre-calculus first course in probability and statistics, and a course in applied linear regression models. No prior knowledge of S or R is assumed. A wide choice of exercises is included, some intended for more advanced students with a first course in mathematical statistics. The authors emphasize parametric log-linear models, while also detailing nonparametric procedures along with model building and data diagnostics. Medical and public health researchers will find the discussion of cut point analysis with bootstrap validation, competing risks and the cumulative incidence estimator, and the analysis of left-truncated and right-censored data invaluable. The bootstrap procedure checks robustness of cut point analysis and determines cut point(s). In a chapter ...

  19. IAEA Review for Gap Analysis of Safety Analysis Capability

    International Nuclear Information System (INIS)

    Basic, Ivica; Kim, Manwoong; Huges, Peter; Lim, B-K; D'Auria, Francesco; Louis, Vidard Michael

    2014-01-01

    The IAEA Asian Nuclear Safety Network (ANSN) was launched in 2002 in the framework of the Extra Budgetary Programme (EBP) on the Safety of Nuclear Installations in the South East Asia, Pacific and Far East Countries. The main objective is to strengthen and expand human and advanced Information Technology (IT) network to pool, analyse and share nuclear safety knowledge and practical experience for peaceful uses in this region. Under the ANSN framework, a technical group on Safety Analysis (SATG) was established in 2004 aimed to providing a forum for the exchange of experience in the following areas of safety analysis: · To provide a forum for an exchange of experience in the area of safety analysis, · To maintain and improve the knowledge on safety analysis method, · To enhance the utilization of computer codes, · To pool and analyse the issues related with safety analysis of research reactor, and · To facilitate mutual interested on safety analysis among member countries. A sustainable and successful nuclear energy programme requires a strong technical infrastructure, including a workforce made up of highly specialized and well-educated professionals. A significant portion of this technical capacity must be dedicated to safety- especially to safety analysis- as only then can it serve as the basis for making the right decisions during the planning, licensing, construction and operation of new nuclear facilities. In this regard, the IAEA has provided ANSN member countries with comprehensive training opportunities for capacity building in safety analysis. Nevertheless, the SATG recognizes that it is difficult to achieve harmonization in this area among all member countries because of their different competency levels. Therefore, it is necessary to quickly identify the most obvious gaps in safety analysis capability and then to use existing resources to begin to fill those gaps. The goal of this Expert Mission (EM) for gap finding service is to facilitate

  20. Hydroeconomic analysis

    DEFF Research Database (Denmark)

    Bauer-Gottwein, Peter; Riegels, Niels; Pulido-Velazquez, Manuel

    2017-01-01

    Hydroeconomic analysis and modeling provides a consistent and quantitative framework to assess the links between water resources systems and economic activities related to water use, simultaneously modeling water supply and water demand. It supports water managers and decision makers in assessing...... trade-offs between different water uses, different geographic regions, and various economic sectors and between the present and the future. Hydroeconomic analysis provides consistent economic performance criteria for infrastructure development and institutional reform in water policies and management...... organizations. This chapter presents an introduction to hydroeconomic analysis and modeling, and reviews the state of the art in the field. We review available economic water-valuation techniques and summarize the main types of decision problems encountered in hydroeconomic analysis. Popular solution strategies...

  1. Sensitivity analysis

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/003741.htm Sensitivity analysis To use the sharing features on this page, please enable JavaScript. Sensitivity analysis determines the effectiveness of antibiotics against microorganisms (germs) ...

  2. The potential for meta-analysis to support decision analysis in ecology.

    Science.gov (United States)

    Mengersen, Kerrie; MacNeil, M Aaron; Caley, M Julian

    2015-06-01

    Meta-analysis and decision analysis are underpinned by well-developed methods that are commonly applied to a variety of problems and disciplines. While these two fields have been closely linked in some disciplines such as medicine, comparatively little attention has been paid to the potential benefits of linking them in ecology, despite reasonable expectations that benefits would be derived from doing so. Meta-analysis combines information from multiple studies to provide more accurate parameter estimates and to reduce the uncertainty surrounding them. Decision analysis involves selecting among alternative choices using statistical information that helps to shed light on the uncertainties involved. By linking meta-analysis to decision analysis, improved decisions can be made, with quantification of the costs and benefits of alternate decisions supported by a greater density of information. Here, we briefly review concepts of both meta-analysis and decision analysis, illustrating the natural linkage between them and the benefits from explicitly linking one to the other. We discuss some examples in which this linkage has been exploited in the medical arena and how improvements in precision and reduction of structural uncertainty inherent in a meta-analysis can provide substantive improvements to decision analysis outcomes by reducing uncertainty in expected loss and maximising information from across studies. We then argue that these significant benefits could be translated to ecology, in particular to the problem of making optimal ecological decisions in the face of uncertainty. Copyright © 2013 John Wiley & Sons, Ltd.

  3. Bayesian Mediation Analysis

    OpenAIRE

    Yuan, Ying; MacKinnon, David P.

    2009-01-01

    This article proposes Bayesian analysis of mediation effects. Compared to conventional frequentist mediation analysis, the Bayesian approach has several advantages. First, it allows researchers to incorporate prior information into the mediation analysis, thus potentially improving the efficiency of estimates. Second, under the Bayesian mediation analysis, inference is straightforward and exact, which makes it appealing for studies with small samples. Third, the Bayesian approach is conceptua...

  4. Economic and Financial Analysis Tools | Energy Analysis | NREL

    Science.gov (United States)

    Economic and Financial Analysis Tools Economic and Financial Analysis Tools Use these economic and . Job and Economic Development Impact (JEDI) Model Use these easy-to-use, spreadsheet-based tools to analyze the economic impacts of constructing and operating power generation and biofuel plants at the

  5. Computational Music Analysis

    DEFF Research Database (Denmark)

    This book provides an in-depth introduction and overview of current research in computational music analysis. Its seventeen chapters, written by leading researchers, collectively represent the diversity as well as the technical and philosophical sophistication of the work being done today...... on well-established theories in music theory and analysis, such as Forte's pitch-class set theory, Schenkerian analysis, the methods of semiotic analysis developed by Ruwet and Nattiez, and Lerdahl and Jackendoff's Generative Theory of Tonal Music. The book is divided into six parts, covering...... music analysis, the book provides an invaluable resource for researchers, teachers and students in music theory and analysis, computer science, music information retrieval and related disciplines. It also provides a state-of-the-art reference for practitioners in the music technology industry....

  6. 6 MV Folded Tandem Ion Accelerator facility at BARC

    International Nuclear Information System (INIS)

    Gupta, S.K.

    2010-01-01

    The 6 MV Folded Tandem Ion Accelerator (FOTIA) facility is operational round the clock and accelerated beams of both light and heavy ions are being used extensively by various divisions of BARC, Universities, lIT Bombay and other R and D labs across the country. The FOTIA is an upgraded version of the old 5.5 MV single stage Van-de-Graaff accelerator (1962-1992). Since its commissioning in the year 2000, the poor beam transmission through the 180 deg folding magnet was a matter of concern. A systematic study for beam transmission through the accelerator was carried out and progressive modifications in folding magnet chamber, foil stripper holder and improvement in average vacuum level through the accelerator have resulted in large improvement of beam transmission leading to up to 2.0 micro-amp analyzed proton beams on target. Now the utilization of the beams from the accelerator has increased many folds for basic and applied research in the fields of atomic and nuclear physics, material science and radiation biology etc. Few new beam lines after the indigenously developed 5-port switching magnet are added and the experimental setup for PIXE, PIGE, External PIXE, 4 neutron detector, Proton Induced Positron Annihilation Spectroscopy (PIPAS) setup and the general purpose scattering chamber etc have been commissioned in the beam hall. The same team has developed a Low Energy Accelerator Facility (LEAF) which delivers negative ions of light and heavy ions for application in implantation, irradiation damage studies in semiconductor devices and testing of new beam line components being developed for Low Energy High Intensity Proton Accelerator (LEHIPA) programme at BARC. The LEAF has been developed as stand alone facility and can deliver beam quickly with minimum intervention of the operator. Few more features are being planned to deliver uniform scanned beams on large targets. (author)

  7. System analysis and design

    International Nuclear Information System (INIS)

    Son, Seung Hui

    2004-02-01

    This book deals with information technology and business process, information system architecture, methods of system development, plan on system development like problem analysis and feasibility analysis, cases for system development, comprehension of analysis of users demands, analysis of users demands using traditional analysis, users demands analysis using integrated information system architecture, system design using integrated information system architecture, system implementation, and system maintenance.

  8. Semen Analysis Test

    Science.gov (United States)

    ... Sources Ask Us Also Known As Sperm Analysis Sperm Count Seminal Fluid Analysis Formal Name Semen Analysis This ... semen Viscosity—consistency or thickness of the semen Sperm count—total number of sperm Sperm concentration (density)—number ...

  9. Qualitative Content Analysis

    Directory of Open Access Journals (Sweden)

    Satu Elo

    2014-02-01

    Full Text Available Qualitative content analysis is commonly used for analyzing qualitative data. However, few articles have examined the trustworthiness of its use in nursing science studies. The trustworthiness of qualitative content analysis is often presented by using terms such as credibility, dependability, conformability, transferability, and authenticity. This article focuses on trustworthiness based on a review of previous studies, our own experiences, and methodological textbooks. Trustworthiness was described for the main qualitative content analysis phases from data collection to reporting of the results. We concluded that it is important to scrutinize the trustworthiness of every phase of the analysis process, including the preparation, organization, and reporting of results. Together, these phases should give a reader a clear indication of the overall trustworthiness of the study. Based on our findings, we compiled a checklist for researchers attempting to improve the trustworthiness of a content analysis study. The discussion in this article helps to clarify how content analysis should be reported in a valid and understandable manner, which would be of particular benefit to reviewers of scientific articles. Furthermore, we discuss that it is often difficult to evaluate the trustworthiness of qualitative content analysis studies because of defective data collection method description and/or analysis description.

  10. Real analysis

    CERN Document Server

    McShane, Edward James

    2013-01-01

    This text surveys practical elements of real function theory, general topology, and functional analysis. Discusses the maximality principle, the notion of convergence, the Lebesgue-Stieltjes integral, function spaces and harmonic analysis. Includes exercises. 1959 edition.

  11. Content analysis and thematic analysis: Implications for conducting a qualitative descriptive study.

    Science.gov (United States)

    Vaismoradi, Mojtaba; Turunen, Hannele; Bondas, Terese

    2013-09-01

    Qualitative content analysis and thematic analysis are two commonly used approaches in data analysis of nursing research, but boundaries between the two have not been clearly specified. In other words, they are being used interchangeably and it seems difficult for the researcher to choose between them. In this respect, this paper describes and discusses the boundaries between qualitative content analysis and thematic analysis and presents implications to improve the consistency between the purpose of related studies and the method of data analyses. This is a discussion paper, comprising an analytical overview and discussion of the definitions, aims, philosophical background, data gathering, and analysis of content analysis and thematic analysis, and addressing their methodological subtleties. It is concluded that in spite of many similarities between the approaches, including cutting across data and searching for patterns and themes, their main difference lies in the opportunity for quantification of data. It means that measuring the frequency of different categories and themes is possible in content analysis with caution as a proxy for significance. © 2013 Wiley Publishing Asia Pty Ltd.

  12. Numerical analysis

    CERN Document Server

    Khabaza, I M

    1960-01-01

    Numerical Analysis is an elementary introduction to numerical analysis, its applications, limitations, and pitfalls. Methods suitable for digital computers are emphasized, but some desk computations are also described. Topics covered range from the use of digital computers in numerical work to errors in computations using desk machines, finite difference methods, and numerical solution of ordinary differential equations. This book is comprised of eight chapters and begins with an overview of the importance of digital computers in numerical analysis, followed by a discussion on errors in comput

  13. Recursive analysis

    CERN Document Server

    Goodstein, R L

    2010-01-01

    Recursive analysis develops natural number computations into a framework appropriate for real numbers. This text is based upon primary recursive arithmetic and presents a unique combination of classical analysis and intuitional analysis. Written by a master in the field, it is suitable for graduate students of mathematics and computer science and can be read without a detailed knowledge of recursive arithmetic.Introductory chapters on recursive convergence and recursive and relative continuity are succeeded by explorations of recursive and relative differentiability, the relative integral, and

  14. Gap Analysis: Application to Earned Value Analysis

    OpenAIRE

    Langford, Gary O.; Franck, Raymond (Chip)

    2008-01-01

    Sponsored Report (for Acquisition Research Program) Earned Value is regarded as a useful tool to monitor commercial and defense system acquisitions. This paper applies the theoretical foundations and systematics of Gap Analysis to improve Earned Value Management. As currently implemented, Earned Value inaccurately provides a higher value for the work performed. This preliminary research indicates that Earned Value calculations can be corrected. Value Analysis, properly defined and enacted,...

  15. CONTENT ANALYSIS, DISCOURSE ANALYSIS, AND CONVERSATION ANALYSIS: PRELIMINARY STUDY ON CONCEPTUAL AND THEORETICAL METHODOLOGICAL DIFFERENCES

    Directory of Open Access Journals (Sweden)

    Anderson Tiago Peixoto Gonçalves

    2016-08-01

    Full Text Available This theoretical essay aims to reflect on three models of text interpretation used in qualitative research, which is often confused in its concepts and methodologies (Content Analysis, Discourse Analysis, and Conversation Analysis. After the presentation of the concepts, the essay proposes a preliminary discussion on conceptual and theoretical methodological differences perceived between them. A review of the literature was performed to support the conceptual and theoretical methodological discussion. It could be verified that the models have differences related to the type of strategy used in the treatment of texts, the type of approach, and the appropriate theoretical position.

  16. Moyer's method of mixed dentition analysis: a meta-analysis ...

    African Journals Online (AJOL)

    The applicability of tables derived from the data Moyer used to other ethnic groups has ... This implies that Moyer's method of prediction may have population variations. ... Key Words: meta-analysis, mixed dentition analysis, Moyer's method

  17. Bayesian Mediation Analysis

    Science.gov (United States)

    Yuan, Ying; MacKinnon, David P.

    2009-01-01

    In this article, we propose Bayesian analysis of mediation effects. Compared with conventional frequentist mediation analysis, the Bayesian approach has several advantages. First, it allows researchers to incorporate prior information into the mediation analysis, thus potentially improving the efficiency of estimates. Second, under the Bayesian…

  18. Applied longitudinal analysis

    CERN Document Server

    Fitzmaurice, Garrett M; Ware, James H

    2012-01-01

    Praise for the First Edition "". . . [this book] should be on the shelf of everyone interested in . . . longitudinal data analysis.""-Journal of the American Statistical Association   Features newly developed topics and applications of the analysis of longitudinal data Applied Longitudinal Analysis, Second Edition presents modern methods for analyzing data from longitudinal studies and now features the latest state-of-the-art techniques. The book emphasizes practical, rather than theoretical, aspects of methods for the analysis of diverse types of lo

  19. Computational movement analysis

    CERN Document Server

    Laube, Patrick

    2014-01-01

    This SpringerBrief discusses the characteristics of spatiotemporal movement data, including uncertainty and scale. It investigates three core aspects of Computational Movement Analysis: Conceptual modeling of movement and movement spaces, spatiotemporal analysis methods aiming at a better understanding of movement processes (with a focus on data mining for movement patterns), and using decentralized spatial computing methods in movement analysis. The author presents Computational Movement Analysis as an interdisciplinary umbrella for analyzing movement processes with methods from a range of fi

  20. Trial Sequential Analysis in systematic reviews with meta-analysis

    DEFF Research Database (Denmark)

    Wetterslev, Jørn; Jakobsen, Janus Christian; Gluud, Christian

    2017-01-01

    BACKGROUND: Most meta-analyses in systematic reviews, including Cochrane ones, do not have sufficient statistical power to detect or refute even large intervention effects. This is why a meta-analysis ought to be regarded as an interim analysis on its way towards a required information size...... from traditional meta-analyses using unadjusted naïve 95% confidence intervals and 5% thresholds for statistical significance. Spurious conclusions in systematic reviews with traditional meta-analyses can be reduced using Trial Sequential Analysis. Several empirical studies have demonstrated...

  1. On-line analysis of reactor noise using time-series analysis

    International Nuclear Information System (INIS)

    McGevna, V.G.

    1981-10-01

    A method to allow use of time series analysis for on-line noise analysis has been developed. On-line analysis of noise in nuclear power reactors has been limited primarily to spectral analysis and related frequency domain techniques. Time series analysis has many distinct advantages over spectral analysis in the automated processing of reactor noise. However, fitting an autoregressive-moving average (ARMA) model to time series data involves non-linear least squares estimation. Unless a high speed, general purpose computer is available, the calculations become too time consuming for on-line applications. To eliminate this problem, a special purpose algorithm was developed for fitting ARMA models. While it is based on a combination of steepest descent and Taylor series linearization, properties of the ARMA model are used so that the auto- and cross-correlation functions can be used to eliminate the need for estimating derivatives. The number of calculations, per iteration varies lineegardless of the mee 0.2% yield strength displayed anisotropy, with axial and circumferential values being greater than radial. For CF8-CPF8 and CF8M-CPF8M castings to meet current ASME Code S acid fuel cells

  2. The Use of Object-Oriented Analysis Methods in Surety Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Craft, Richard L.; Funkhouser, Donald R.; Wyss, Gregory D.

    1999-05-01

    Object-oriented analysis methods have been used in the computer science arena for a number of years to model the behavior of computer-based systems. This report documents how such methods can be applied to surety analysis. By embodying the causality and behavior of a system in a common object-oriented analysis model, surety analysts can make the assumptions that underlie their models explicit and thus better communicate with system designers. Furthermore, given minor extensions to traditional object-oriented analysis methods, it is possible to automatically derive a wide variety of traditional risk and reliability analysis methods from a single common object model. Automatic model extraction helps ensure consistency among analyses and enables the surety analyst to examine a system from a wider variety of viewpoints in a shorter period of time. Thus it provides a deeper understanding of a system's behaviors and surety requirements. This report documents the underlying philosophy behind the common object model representation, the methods by which such common object models can be constructed, and the rules required to interrogate the common object model for derivation of traditional risk and reliability analysis models. The methodology is demonstrated in an extensive example problem.

  3. Circuit analysis for dummies

    CERN Document Server

    Santiago, John

    2013-01-01

    Circuits overloaded from electric circuit analysis? Many universities require that students pursuing a degree in electrical or computer engineering take an Electric Circuit Analysis course to determine who will ""make the cut"" and continue in the degree program. Circuit Analysis For Dummies will help these students to better understand electric circuit analysis by presenting the information in an effective and straightforward manner. Circuit Analysis For Dummies gives you clear-cut information about the topics covered in an electric circuit analysis courses to help

  4. Hazard Analysis Database Report

    CERN Document Server

    Grams, W H

    2000-01-01

    The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for U S . Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for HNF-SD-WM-SAR-067, Tank Farms Final Safety Analysis Report (FSAR). The FSAR is part of the approved Authorization Basis (AB) for the River Protection Project (RPP). This document describes, identifies, and defines the contents and structure of the Tank Farms FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The Hazard Analysis Database supports the preparation of Chapters 3 ,4 , and 5 of the Tank Farms FSAR and the Unreviewed Safety Question (USQ) process and consists of two major, interrelated data sets: (1) Hazard Analysis Database: Data from t...

  5. Descriptive data analysis.

    Science.gov (United States)

    Thompson, Cheryl Bagley

    2009-01-01

    This 13th article of the Basics of Research series is first in a short series on statistical analysis. These articles will discuss creating your statistical analysis plan, levels of measurement, descriptive statistics, probability theory, inferential statistics, and general considerations for interpretation of the results of a statistical analysis.

  6. International Market Analysis

    DEFF Research Database (Denmark)

    Sørensen, Olav Jull

    2009-01-01

    The review presents the book International Market Analysis: Theories and Methods, written by John Kuiada, professor at Centre of International Business, Department of Business Studies, Aalborg University. The book is refreshingly new in its way of looking at a classical problem. It looks at market...... analysis from the point of vie of ways of thinking about markets. Furthermore, the book includes the concept of learning in the analysis of markets og how the way we understand business reality influneces our choice of methodology for market analysis....

  7. Improvement of Binary Analysis Components in Automated Malware Analysis Framework

    Science.gov (United States)

    2017-02-21

    AFRL-AFOSR-JP-TR-2017-0018 Improvement of Binary Analysis Components in Automated Malware Analysis Framework Keiji Takeda KEIO UNIVERSITY Final...TYPE Final 3. DATES COVERED (From - To) 26 May 2015 to 25 Nov 2016 4. TITLE AND SUBTITLE Improvement of Binary Analysis Components in Automated Malware ...analyze malicious software ( malware ) with minimum human interaction. The system autonomously analyze malware samples by analyzing malware binary program

  8. Analysis of mineral phases in coal utilizing factor analysis

    International Nuclear Information System (INIS)

    Roscoe, B.A.; Hopke, P.K.

    1982-01-01

    The mineral phase inclusions of coal are discussed. The contribution of these to a coal sample are determined utilizing several techniques. Neutron activation analysis in conjunction with coal washability studies have produced some information on the general trends of elemental variation in the mineral phases. These results have been enhanced by the use of various statistical techniques. The target transformation factor analysis is specifically discussed and shown to be able to produce elemental profiles of the mineral phases in coal. A data set consisting of physically fractionated coal samples was generated. These samples were analyzed by neutron activation analysis and then their elemental concentrations examined using TTFA. Information concerning the mineral phases in coal can thus be acquired from factor analysis even with limited data. Additional data may permit the resolution of additional mineral phases as well as refinement of theose already identified

  9. Meta-analysis with R

    CERN Document Server

    Schwarzer, Guido; Rücker, Gerta

    2015-01-01

    This book provides a comprehensive introduction to performing meta-analysis using the statistical software R. It is intended for quantitative researchers and students in the medical and social sciences who wish to learn how to perform meta-analysis with R. As such, the book introduces the key concepts and models used in meta-analysis. It also includes chapters on the following advanced topics: publication bias and small study effects; missing data; multivariate meta-analysis, network meta-analysis; and meta-analysis of diagnostic studies.  .

  10. Cluster analysis for applications

    CERN Document Server

    Anderberg, Michael R

    1973-01-01

    Cluster Analysis for Applications deals with methods and various applications of cluster analysis. Topics covered range from variables and scales to measures of association among variables and among data units. Conceptual problems in cluster analysis are discussed, along with hierarchical and non-hierarchical clustering methods. The necessary elements of data analysis, statistics, cluster analysis, and computer implementation are integrated vertically to cover the complete path from raw data to a finished analysis.Comprised of 10 chapters, this book begins with an introduction to the subject o

  11. Job Analysis

    OpenAIRE

    Bravená, Helena

    2009-01-01

    This bacherlor thesis deals with the importance of job analysis for personnel activities in the company. The aim of this work is to find the most suitable method of job analysis in a particular enterprise, and continues creating descriptions and specifications of each job.

  12. Visual physics analysis VISPA

    International Nuclear Information System (INIS)

    Actis, Oxana; Brodski, Michael; Erdmann, Martin; Fischer, Robert; Hinzmann, Andreas; Mueller, Gero; Muenzer, Thomas; Plum, Matthias; Steggemann, Jan; Winchen, Tobias; Klimkovich, Tatsiana

    2010-01-01

    VISPA is a development environment for high energy physics analyses which enables physicists to combine graphical and textual work. A physics analysis cycle consists of prototyping, performing, and verifying the analysis. The main feature of VISPA is a multipurpose window for visual steering of analysis steps, creation of analysis templates, and browsing physics event data at different steps of an analysis. VISPA follows an experiment-independent approach and incorporates various tools for steering and controlling required in a typical analysis. Connection to different frameworks of high energy physics experiments is achieved by using different types of interfaces. We present the look-and-feel for an example physics analysis at the LHC and explain the underlying software concepts of VISPA.

  13. Analysis of the interaction between experimental and applied behavior analysis.

    Science.gov (United States)

    Virues-Ortega, Javier; Hurtado-Parrado, Camilo; Cox, Alison D; Pear, Joseph J

    2014-01-01

    To study the influences between basic and applied research in behavior analysis, we analyzed the coauthorship interactions of authors who published in JABA and JEAB from 1980 to 2010. We paid particular attention to authors who published in both JABA and JEAB (dual authors) as potential agents of cross-field interactions. We present a comprehensive analysis of dual authors' coauthorship interactions using social networks methodology and key word analysis. The number of dual authors more than doubled (26 to 67) and their productivity tripled (7% to 26% of JABA and JEAB articles) between 1980 and 2010. Dual authors stood out in terms of number of collaborators, number of publications, and ability to interact with multiple groups within the field. The steady increase in JEAB and JABA interactions through coauthors and the increasing range of topics covered by dual authors provide a basis for optimism regarding the progressive integration of basic and applied behavior analysis. © Society for the Experimental Analysis of Behavior.

  14. K Basin Hazard Analysis

    Energy Technology Data Exchange (ETDEWEB)

    PECH, S.H.

    2000-08-23

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  15. K Basin Hazard Analysis

    International Nuclear Information System (INIS)

    PECH, S.H.

    2000-01-01

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

  16. Energy analysis handbook. CAC document 214. [Combining process analysis with input-output analysis

    Energy Technology Data Exchange (ETDEWEB)

    Bullard, C. W.; Penner, P. S.; Pilati, D. A.

    1976-10-01

    Methods are presented for calculating the energy required, directly and indirectly, to produce all types of goods and services. Procedures for combining process analysis with input-output analysis are described. This enables the analyst to focus data acquisition cost-effectively, and to achieve a specified degree of accuracy in the results. The report presents sample calculations and provides the tables and charts needed to perform most energy cost calculations, including the cost of systems for producing or conserving energy.

  17. Hypothesis analysis methods, hypothesis analysis devices, and articles of manufacture

    Science.gov (United States)

    Sanfilippo, Antonio P [Richland, WA; Cowell, Andrew J [Kennewick, WA; Gregory, Michelle L [Richland, WA; Baddeley, Robert L [Richland, WA; Paulson, Patrick R [Pasco, WA; Tratz, Stephen C [Richland, WA; Hohimer, Ryan E [West Richland, WA

    2012-03-20

    Hypothesis analysis methods, hypothesis analysis devices, and articles of manufacture are described according to some aspects. In one aspect, a hypothesis analysis method includes providing a hypothesis, providing an indicator which at least one of supports and refutes the hypothesis, using the indicator, associating evidence with the hypothesis, weighting the association of the evidence with the hypothesis, and using the weighting, providing information regarding the accuracy of the hypothesis.

  18. The CHARISMA project in ATOMKI

    International Nuclear Information System (INIS)

    Szikszai, Z.; Csedreki, L.; Furu, E.; Kertesz, Zs.; Kiss, A.Z.; Uzonyi, I.; Simon, A.

    2010-01-01

    Complete text of publication follows. CHARISMA (Cultural Heritage Advanced Research Infrastructures: Synergy for a Multidisciplinary Approach to Conservation / Restoration) is an EU-funded integrating activity project carried out in the FP7 Capacities Specific Programme 'Research Infrastructures'. It started in 2009 and will end in 2013. The project provides transnational access (TNA) to advanced scientific instrumentations and knowledge allowing scientists, conservators-restorers and curators to enhance their research at the field forefront. ARCHLAB permits the access to the structured scientific information and analytical data, stored in the archives of the most prestigious European museums and conservation institutions. MOLAB offers access to a portable set of advanced analytical equipment, for in situ non-invasive measurements on artworks. FIXLAB provides access to large and medium scale European installations, including the beamlines of one synchrotron radiation, one neutron source and two ion-beam analytical facilities. Access to these facilities is offered free of charge to users working in the EC Member and Associated States, particularly to first time users, and granted on the basis of project proposals which are reviewed and evaluated through a Peer Review selection. Calls are published twice a year on the CHARISMA website and the local websites of the institutions. The Laboratory of Ion Beam Applications in ATOMKI-HAS is equipped with a 5 MV Van de Graaff electrostatic accelerator, as well as ion beam analytical facilities and instruments. The assortment of ion beams and their energy range makes it possible to apply most of the non-invasive ion beam analytical techniques used for the study of cultural heritage. The following methods are available: Particle Induced X-ray Emission technique (PIXE), Rutherford Backscattering Spectrometry (RBS), Particle Induced Gamma-ray Emission technique (PIGE), Nuclear Reaction Analysis (NRA), Elastic Recoil Detection

  19. Analysis I

    CERN Document Server

    Tao, Terence

    2016-01-01

    This is part one of a two-volume book on real analysis and is intended for senior undergraduate students of mathematics who have already been exposed to calculus. The emphasis is on rigour and foundations of analysis. Beginning with the construction of the number systems and set theory, the book discusses the basics of analysis (limits, series, continuity, differentiation, Riemann integration), through to power series, several variable calculus and Fourier analysis, and then finally the Lebesgue integral. These are almost entirely set in the concrete setting of the real line and Euclidean spaces, although there is some material on abstract metric and topological spaces. The book also has appendices on mathematical logic and the decimal system. The entire text (omitting some less central topics) can be taught in two quarters of 25–30 lectures each. The course material is deeply intertwined with the exercises, as it is intended that the student actively learn the material (and practice thinking and writing ri...

  20. Analysis II

    CERN Document Server

    Tao, Terence

    2016-01-01

    This is part two of a two-volume book on real analysis and is intended for senior undergraduate students of mathematics who have already been exposed to calculus. The emphasis is on rigour and foundations of analysis. Beginning with the construction of the number systems and set theory, the book discusses the basics of analysis (limits, series, continuity, differentiation, Riemann integration), through to power series, several variable calculus and Fourier analysis, and then finally the Lebesgue integral. These are almost entirely set in the concrete setting of the real line and Euclidean spaces, although there is some material on abstract metric and topological spaces. The book also has appendices on mathematical logic and the decimal system. The entire text (omitting some less central topics) can be taught in two quarters of 25–30 lectures each. The course material is deeply intertwined with the exercises, as it is intended that the student actively learn the material (and practice thinking and writing ri...

  1. CMS analysis operations

    International Nuclear Information System (INIS)

    Andreeva, J; Maier, G; Spiga, D; Calloni, M; Colling, D; Fanzago, F; D'Hondt, J; Maes, J; Van Mulders, P; Villella, I; Klem, J; Letts, J; Padhi, S; Sarkar, S

    2010-01-01

    During normal data taking CMS expects to support potentially as many as 2000 analysis users. Since the beginning of 2008 there have been more than 800 individuals who submitted a remote analysis job to the CMS computing infrastructure. The bulk of these users will be supported at the over 40 CMS Tier-2 centres. Supporting a globally distributed community of users on a globally distributed set of computing clusters is a task that requires reconsidering the normal methods of user support for Analysis Operations. In 2008 CMS formed an Analysis Support Task Force in preparation for large-scale physics analysis activities. The charge of the task force was to evaluate the available support tools, the user support techniques, and the direct feedback of users with the goal of improving the success rate and user experience when utilizing the distributed computing environment. The task force determined the tools needed to assess and reduce the number of non-zero exit code applications submitted through the grid interfaces and worked with the CMS experiment dashboard developers to obtain the necessary information to quickly and proactively identify issues with user jobs and data sets hosted at various sites. Results of the analysis group surveys were compiled. Reference platforms for testing and debugging problems were established in various geographic regions. The task force also assessed the resources needed to make the transition to a permanent Analysis Operations task. In this presentation the results of the task force will be discussed as well as the CMS Analysis Operations plans for the start of data taking.

  2. Harmonic analysis a comprehensive course in analysis, part 3

    CERN Document Server

    Simon, Barry

    2015-01-01

    A Comprehensive Course in Analysis by Poincaré Prize winner Barry Simon is a five-volume set that can serve as a graduate-level analysis textbook with a lot of additional bonus information, including hundreds of problems and numerous notes that extend the text and provide important historical background. Depth and breadth of exposition make this set a valuable reference source for almost all areas of classical analysis. Part 3 returns to the themes of Part 1 by discussing pointwise limits (going beyond the usual focus on the Hardy-Littlewood maximal function by including ergodic theorems and m

  3. Cost benefit analysis cost effectiveness analysis

    International Nuclear Information System (INIS)

    Lombard, J.

    1986-09-01

    The comparison of various protection options in order to determine which is the best compromise between cost of protection and residual risk is the purpose of the ALARA procedure. The use of decision-aiding techniques is valuable as an aid to selection procedures. The purpose of this study is to introduce two rather simple and well known decision aiding techniques: the cost-effectiveness analysis and the cost-benefit analysis. These two techniques are relevant for the great part of ALARA decisions which need the use of a quantitative technique. The study is based on an hypothetical case of 10 protection options. Four methods are applied to the data

  4. Basic complex analysis a comprehensive course in analysis, part 2a

    CERN Document Server

    Simon, Barry

    2015-01-01

    A Comprehensive Course in Analysis by Poincaré Prize winner Barry Simon is a five-volume set that can serve as a graduate-level analysis textbook with a lot of additional bonus information, including hundreds of problems and numerous notes that extend the text and provide important historical background. Depth and breadth of exposition make this set a valuable reference source for almost all areas of classical analysis. Part 2A is devoted to basic complex analysis. It interweaves three analytic threads associated with Cauchy, Riemann, and Weierstrass, respectively. Cauchy's view focuses on th

  5. pyAudioAnalysis: An Open-Source Python Library for Audio Signal Analysis.

    Science.gov (United States)

    Giannakopoulos, Theodoros

    2015-01-01

    Audio information plays a rather important role in the increasing digital content that is available today, resulting in a need for methodologies that automatically analyze such content: audio event recognition for home automations and surveillance systems, speech recognition, music information retrieval, multimodal analysis (e.g. audio-visual analysis of online videos for content-based recommendation), etc. This paper presents pyAudioAnalysis, an open-source Python library that provides a wide range of audio analysis procedures including: feature extraction, classification of audio signals, supervised and unsupervised segmentation and content visualization. pyAudioAnalysis is licensed under the Apache License and is available at GitHub (https://github.com/tyiannak/pyAudioAnalysis/). Here we present the theoretical background behind the wide range of the implemented methodologies, along with evaluation metrics for some of the methods. pyAudioAnalysis has been already used in several audio analysis research applications: smart-home functionalities through audio event detection, speech emotion recognition, depression classification based on audio-visual features, music segmentation, multimodal content-based movie recommendation and health applications (e.g. monitoring eating habits). The feedback provided from all these particular audio applications has led to practical enhancement of the library.

  6. Introduction of thermal-hydraulic analysis code and system analysis code for HTGR

    International Nuclear Information System (INIS)

    Tanaka, Mitsuhiro; Izaki, Makoto; Koike, Hiroyuki; Tokumitsu, Masashi

    1984-01-01

    Kawasaki Heavy Industries Ltd. has advanced the development and systematization of analysis codes, aiming at lining up the analysis codes for heat transferring flow and control characteristics, taking up HTGR plants as the main object. In order to make the model of flow when shock waves propagate to heating tubes, SALE-3D which can analyze a complex system was developed, therefore, it is reported in this paper. Concerning the analysis code for control characteristics, the method of sensitivity analysis in a topological space including an example of application is reported. The flow analysis code SALE-3D is that for analyzing the flow of compressible viscous fluid in a three-dimensional system over the velocity range from incompressibility limit to supersonic velocity. The fundamental equations and fundamental algorithm of the SALE-3D, the calculation of cell volume, the plotting of perspective drawings and the analysis of the three-dimensional behavior of shock waves propagating in heating tubes after their rupture accident are described. The method of sensitivity analysis was added to the analysis code for control characteristics in a topological space, and blow-down phenomena was analyzed by its application. (Kako, I.)

  7. Investigation on method of elasto-plastic analysis for piping system (benchmark analysis)

    International Nuclear Information System (INIS)

    Kabaya, Takuro; Kojima, Nobuyuki; Arai, Masashi

    2015-01-01

    This paper provides method of an elasto-plastic analysis for practical seismic design of nuclear piping system. JSME started up the task to establish method of an elasto-plastic analysis for nuclear piping system. The benchmark analyses have been performed in the task to investigate on method of an elasto-plastic analysis. And our company has participated in the benchmark analyses. As a result, we have settled on the method which simulates the result of piping exciting test accurately. Therefore the recommended method of an elasto-plastic analysis is shown as follows; 1) An elasto-plastic analysis is composed of dynamic analysis of piping system modeled by using beam elements and static analysis of deformed elbow modeled by using shell elements. 2) Bi-linear is applied as an elasto-plastic property. Yield point is standardized yield point multiplied by 1.2 times, and second gradient is 1/100 young's modulus. Kinematic hardening is used as a hardening rule. 3) The fatigue life is evaluated on strain ranges obtained by elasto-plastic analysis, by using the rain flow method and the fatigue curve of previous studies. (author)

  8. K Basins Hazard Analysis

    International Nuclear Information System (INIS)

    WEBB, R.H.

    1999-01-01

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Safety Analysis Report (HNF-SD-WM-SAR-062/Rev.4). This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report

  9. Functional data analysis

    CERN Document Server

    Ramsay, J O

    1997-01-01

    Scientists today collect samples of curves and other functional observations. This monograph presents many ideas and techniques for such data. Included are expressions in the functional domain of such classics as linear regression, principal components analysis, linear modelling, and canonical correlation analysis, as well as specifically functional techniques such as curve registration and principal differential analysis. Data arising in real applications are used throughout for both motivation and illustration, showing how functional approaches allow us to see new things, especially by exploiting the smoothness of the processes generating the data. The data sets exemplify the wide scope of functional data analysis; they are drwan from growth analysis, meterology, biomechanics, equine science, economics, and medicine. The book presents novel statistical technology while keeping the mathematical level widely accessible. It is designed to appeal to students, to applied data analysts, and to experienced researc...

  10. Dimensional Analysis

    Indian Academy of Sciences (India)

    Dimensional analysis is a useful tool which finds important applications in physics and engineering. It is most effective when there exist a maximal number of dimensionless quantities constructed out of the relevant physical variables. Though a complete theory of dimen- sional analysis was developed way back in 1914 in a.

  11. A sensory analysis of butter cookies: An application of generalized procrustes analysis

    DEFF Research Database (Denmark)

    Juhl, Hans Jørn

    1994-01-01

    Executive Summary: 1. A sensory analysis is one of the first steps in product development in the food industry. A thorough analysis of the results from such an analysis may give important input to the development process. 2. A sensory analysis on butter cookies is conducted in order to evaluate...... if some butter may be replaced by vegetable fat without a significant change in the sensory profile. The conclusion is that the replacement is possible without a considerable change in the sensory profile. 3. Generalized Procrustes Analysis is used to analyze the results. It is a relatively new technique...

  12. Contributions to sensitivity analysis and generalized discriminant analysis

    International Nuclear Information System (INIS)

    Jacques, J.

    2005-12-01

    Two topics are studied in this thesis: sensitivity analysis and generalized discriminant analysis. Global sensitivity analysis of a mathematical model studies how the output variables of this last react to variations of its inputs. The methods based on the study of the variance quantify the part of variance of the response of the model due to each input variable and each subset of input variables. The first subject of this thesis is the impact of a model uncertainty on results of a sensitivity analysis. Two particular forms of uncertainty are studied: that due to a change of the model of reference, and that due to the use of a simplified model with the place of the model of reference. A second problem was studied during this thesis, that of models with correlated inputs. Indeed, classical sensitivity indices not having significance (from an interpretation point of view) in the presence of correlation of the inputs, we propose a multidimensional approach consisting in expressing the sensitivity of the output of the model to groups of correlated variables. Applications in the field of nuclear engineering illustrate this work. Generalized discriminant analysis consists in classifying the individuals of a test sample in groups, by using information contained in a training sample, when these two samples do not come from the same population. This work extends existing methods in a Gaussian context to the case of binary data. An application in public health illustrates the utility of generalized discrimination models thus defined. (author)

  13. Chemical analysis of carbonates and carbonate rocks by atomic absorption analysis

    Energy Technology Data Exchange (ETDEWEB)

    Tardon, S

    1981-01-01

    Evaluates methods of determining chemical composition of rocks surrounding black coal seams. Carbonate rock samples were collected in the Ostrava-Karvina coal mines. Sampling methods are described. Determination of the following elements and compounds in carbonate rocks is discussed: calcium, magnesium, iron, manganese, barium, silicon, aluminium, titanium, sodium, potassium, sulfur trioxide, phosphorus pentoxide, water and carbon dioxide. Proportion of compounds insoluble in water in the investigated rocks is also determined. Most of the elements are determined by means of atomic absorption analysis. Phosphorus is also determined by atomic absorption analysis. Other compounds are determined gravimetrically. The described procedure permits weight of a rock sample to be reduced to 0.5 g without reducing analysis accuracy. The results of determining carbonate rock components by X-ray analysis and by chemical analysis are compared. Equipment used for atomic absorption analysis is characterized (the 503 Perkin-Elmer and the CF-4 Optica-Milano spectrophotometers). The analyzed method for determining carbonate rock permits more accurate classification of rocks surrounding coal seams and rock impurities in run-of-mine coal. (22 refs.) (In Czech)

  14. Practical data analysis

    CERN Document Server

    Cuesta, Hector

    2013-01-01

    Each chapter of the book quickly introduces a key 'theme' of Data Analysis, before immersing you in the practical aspects of each theme. You'll learn quickly how to perform all aspects of Data Analysis.Practical Data Analysis is a book ideal for home and small business users who want to slice & dice the data they have on hand with minimum hassle.

  15. Left ventricular wall motion abnormalities evaluated by factor analysis as compared with Fourier analysis

    International Nuclear Information System (INIS)

    Hirota, Kazuyoshi; Ikuno, Yoshiyasu; Nishikimi, Toshio

    1986-01-01

    Factor analysis was applied to multigated cardiac pool scintigraphy to evaluate its ability to detect left ventricular wall motion abnormalities in 35 patients with old myocardial infarction (MI), and in 12 control cases with normal left ventriculography. All cases were also evaluated by conventional Fourier analysis. In most cases with normal left ventriculography, the ventricular and atrial factors were extracted by factor analysis. In cases with MI, the third factor was obtained in the left ventricle corresponding to wall motion abnormality. Each case was scored according to the coincidence of findings of ventriculography and those of factor analysis or Fourier analysis. Scores were recorded for three items; the existence, location, and degree of asynergy. In cases of MI, the detection rate of asynergy was 94 % by factor analysis, 83 % by Fourier analysis, and the agreement in respect to location was 71 % and 66 %, respectively. Factor analysis had higher scores than Fourier analysis, but this was not significant. The interobserver error of factor analysis was less than that of Fourier analysis. Factor analysis can display locations and dynamic motion curves of asynergy, and it is regarded as a useful method for detecting and evaluating left ventricular wall motion abnormalities. (author)

  16. Time-frequency analysis : mathematical analysis of the empirical mode decomposition.

    Science.gov (United States)

    2009-01-01

    Invented over 10 years ago, empirical mode : decomposition (EMD) provides a nonlinear : time-frequency analysis with the ability to successfully : analyze nonstationary signals. Mathematical : Analysis of the Empirical Mode Decomposition : is a...

  17. QUANTITATIVE ANALYSIS OF FLUX REGULATION THROUGH HIERARCHICAL REGULATION ANALYSIS

    NARCIS (Netherlands)

    van Eunen, Karen; Rossell, Sergio; Bouwman, Jildau; Westerhoff, Hans V.; Bakker, Barbara M.; Jameson, D; Verma, M; Westerhoff, HV

    2011-01-01

    Regulation analysis is a methodology that quantifies to what extent a change in the flux through a metabolic pathway is regulated by either gene expression or metabolism. Two extensions to regulation analysis were developed over the past years: (i) the regulation of V(max) can be dissected into the

  18. Quantitative analysis of flux regulation through hierarchical regulation analysis

    NARCIS (Netherlands)

    Eunen, K. van; Rossell, S.; Bouwman, J.; Westerhoff, H.V.; Bakker, B.M.

    2011-01-01

    Regulation analysis is a methodology that quantifies to what extent a change in the flux through a metabolic pathway is regulated by either gene expression or metabolism. Two extensions to regulation analysis were developed over the past years: (i) the regulation of Vmax can be dissected into the

  19. Object-Oriented Analysis, Structured Analysis, and Jackson System Development

    NARCIS (Netherlands)

    Van Assche, F.; Wieringa, Roelf J.; Moulin, B.; Rolland, C

    1991-01-01

    Conceptual modeling is the activity of producing a conceptual model of an actual or desired version of a universe of discourse (UoD). In this paper, two methods of conceptual modeling are compared, structured analysis (SA) and object-oriented analysis (OOA). This is done by transforming a model

  20. Foundations of mathematical analysis

    CERN Document Server

    Johnsonbaugh, Richard

    2010-01-01

    This classroom-tested volume offers a definitive look at modern analysis, with views of applications to statistics, numerical analysis, Fourier series, differential equations, mathematical analysis, and functional analysis. Upper-level undergraduate students with a background in calculus will benefit from its teachings, along with beginning graduate students seeking a firm grounding in modern analysis. A self-contained text, it presents the necessary background on the limit concept, and the first seven chapters could constitute a one-semester introduction to limits. Subsequent chapters discuss

  1. Advanced complex analysis a comprehensive course in analysis, part 2b

    CERN Document Server

    Simon, Barry

    2015-01-01

    A Comprehensive Course in Analysis by Poincaré Prize winner Barry Simon is a five-volume set that can serve as a graduate-level analysis textbook with a lot of additional bonus information, including hundreds of problems and numerous notes that extend the text and provide important historical background. Depth and breadth of exposition make this set a valuable reference source for almost all areas of classical analysis. Part 2B provides a comprehensive look at a number of subjects of complex analysis not included in Part 2A. Presented in this volume are the theory of conformal metrics (includ

  2. Development of Performance Analysis Program for an Axial Compressor with Meanline Analysis

    International Nuclear Information System (INIS)

    Park, Jun Young; Park, Moo Ryong; Choi, Bum Suk; Song, Je Wook

    2009-01-01

    Axial-flow compressor is one of the most important parts of gas turbine units with axial turbine and combustor. Therefore, precise prediction of performance is very important for development of new compressor or modification of existing one. Meanline analysis is a simple, fast and powerful method for performance prediction of axial-flow compressors with different geometries. So, Meanline analysis is frequently used in preliminary design stage and performance analysis for given geometry data. Much correlations for meanline analysis have been developed theoretically and experimentally for estimating various types of losses and flow deviation angle for long time. In present study, meanline analysis program was developed to estimate compressor losses, incidence angles, deviation angles, stall and surge conditions with many correlations. Performance prediction of one stage axial compressors is conducted with this meanline analysis program. The comparison between experimental and numerical results show a good agreement. This meanline analysis program can be used for various types of single stage axial-flow compressors with different geometries, as well as multistage axial-flow compressors

  3. Nonactivation interaction analysis. Chapter 5

    International Nuclear Information System (INIS)

    1976-01-01

    Analyses are described including the alpha scattering analysis, beta absorption and scattering analysis, gamma and X-ray absorption and scattering analysis, X-ray fluorescence analysis, neutron absorption and scattering analysis, Moessbauer effect application and an analysis based on the application of radiation ionizing effects. (J.P.)

  4. Goal-oriented failure analysis - a systems analysis approach to hazard identification

    International Nuclear Information System (INIS)

    Reeves, A.B.; Davies, J.; Foster, J.; Wells, G.L.

    1990-01-01

    Goal-Oriented Failure Analysis, GOFA, is a methodology which is being developed to identify and analyse the potential failure modes of a hazardous plant or process. The technique will adopt a structured top-down approach, with a particular failure goal being systematically analysed. A systems analysis approach is used, with the analysis being organised around a systems diagram of the plant or process under study. GOFA will also use checklists to supplement the analysis -these checklists will be prepared in advance of a group session and will help to guide the analysis and avoid unnecessary time being spent on identifying obvious failure modes or failing to identify certain hazards or failures. GOFA is being developed with the aim of providing a hazard identification methodology which is more efficient and stimulating than the conventional approach to HAZOP. The top-down approach should ensure that the analysis is more focused and the use of a systems diagram will help to pull the analysis together at an early stage whilst also helping to structure the sessions in a more stimulating way than the conventional techniques. GOFA will be, essentially, an extension of the HAZOP methodology. GOFA is currently being computerised using a knowledge-based systems approach for implementation. The Goldworks II expert systems development tool is being used. (author)

  5. Trace analysis

    International Nuclear Information System (INIS)

    Warner, M.

    1987-01-01

    What is the current state of quantitative trace analytical chemistry? What are today's research efforts? And what challenges does the future hold? These are some of the questions addressed at a recent four-day symposium sponsored by the National Bureau of Standards (NBS) entitled Accuracy in Trace Analysis - Accomplishments, Goals, Challenges. The two plenary sessions held on the first day of the symposium reviewed the history of quantitative trace analysis, discussed the present situation from academic and industrial perspectives, and summarized future needs. The remaining three days of the symposium consisted of parallel sessions dealing with the measurement process; quantitation in materials; environmental, clinical, and nutrient analysis; and advances in analytical techniques

  6. Analysis in usability evaluations

    DEFF Research Database (Denmark)

    Følstad, Asbjørn; Lai-Chong Law, Effie; Hornbæk, Kasper

    2010-01-01

    While the planning and implementation of usability evaluations are well described in the literature, the analysis of the evaluation data is not. We present interviews with 11 usability professionals on how they conduct analysis, describing the resources, collaboration, creation of recommendations......, and prioritization involved. The interviews indicate a lack of structure in the analysis process and suggest activities, such as generating recommendations, that are unsupported by existing methods. We discuss how to better support analysis, and propose four themes for future research on analysis in usability...

  7. What Is Public Agency Strategic Analysis (PASA and How Does It Differ from Public Policy Analysis and Firm Strategy Analysis?

    Directory of Open Access Journals (Sweden)

    Aidan R. Vining

    2016-12-01

    Full Text Available Public agency strategic analysis (PASA is different from public policy analysis because public agency executives face numerous constraints that those performing “unconstrained” policy analysis do not. It is also different from private sector strategic analysis. But because of similar constraints and realities, some generic and private sector strategic analysis techniques can be useful to those carrying out PASA, if appropriately modified. Analysis of the external agency environment (external forces and internal value creation processes (“value chains”, “modular assembly” processes or “multi-sided intermediation platforms” are the most important components of PASA. Also, agency executives must focus on feasible alternatives. In sum, PASA must be practical. But public executives need to take seriously public value, and specifically social efficiency, when engaging in PASA. Unless they do so, their strategic analyses will not have normative legitimacy because enhancing public value is not the same as in some versions of public value or in agency “profit maximization”. Although similarly constrained, normatively appropriate public agency strategic analysis is not “giving clients what they want” or “making the public sector business case”. PASA must be both practical and principled.

  8. Foundations of factor analysis

    CERN Document Server

    Mulaik, Stanley A

    2009-01-01

    Introduction Factor Analysis and Structural Theories Brief History of Factor Analysis as a Linear Model Example of Factor AnalysisMathematical Foundations for Factor Analysis Introduction Scalar AlgebraVectorsMatrix AlgebraDeterminants Treatment of Variables as Vectors Maxima and Minima of FunctionsComposite Variables and Linear Transformations Introduction Composite Variables Unweighted Composite VariablesDifferentially Weighted Composites Matrix EquationsMulti

  9. Is activation analysis still active?

    International Nuclear Information System (INIS)

    Chai Zhifang

    2001-01-01

    This paper reviews some aspects of neutron activation analysis (NAA), covering instrumental neutron activation analysis (INAA), k 0 method, prompt gamma-ray neutron activation analysis (PGNAA), radiochemical neutron activation analysis (RNAA) and molecular activation analysis (MAA). The comparison of neutron activation analysis with other analytical techniques are also made. (author)

  10. Semiotic Analysis.

    Science.gov (United States)

    Thiemann, Francis C.

    Semiotic analysis is a method of analyzing signs (e.g., words) to reduce non-numeric data to their component parts without losing essential meanings. Semiotics dates back to Aristotle's analysis of language; it was much advanced by nineteenth-century analyses of style and logic and by Whitehead and Russell's description in this century of the role…

  11. Multivariate analysis with LISREL

    CERN Document Server

    Jöreskog, Karl G; Y Wallentin, Fan

    2016-01-01

    This book traces the theory and methodology of multivariate statistical analysis and shows how it can be conducted in practice using the LISREL computer program. It presents not only the typical uses of LISREL, such as confirmatory factor analysis and structural equation models, but also several other multivariate analysis topics, including regression (univariate, multivariate, censored, logistic, and probit), generalized linear models, multilevel analysis, and principal component analysis. It provides numerous examples from several disciplines and discusses and interprets the results, illustrated with sections of output from the LISREL program, in the context of the example. The book is intended for masters and PhD students and researchers in the social, behavioral, economic and many other sciences who require a basic understanding of multivariate statistical theory and methods for their analysis of multivariate data. It can also be used as a textbook on various topics of multivariate statistical analysis.

  12. An Array of Qualitative Data Analysis Tools: A Call for Data Analysis Triangulation

    Science.gov (United States)

    Leech, Nancy L.; Onwuegbuzie, Anthony J.

    2007-01-01

    One of the most important steps in the qualitative research process is analysis of data. The purpose of this article is to provide elements for understanding multiple types of qualitative data analysis techniques available and the importance of utilizing more than one type of analysis, thus utilizing data analysis triangulation, in order to…

  13. Essential real analysis

    CERN Document Server

    Field, Michael

    2017-01-01

    This book provides a rigorous introduction to the techniques and results of real analysis, metric spaces and multivariate differentiation, suitable for undergraduate courses. Starting from the very foundations of analysis, it offers a complete first course in real analysis, including topics rarely found in such detail in an undergraduate textbook such as the construction of non-analytic smooth functions, applications of the Euler-Maclaurin formula to estimates, and fractal geometry.  Drawing on the author’s extensive teaching and research experience, the exposition is guided by carefully chosen examples and counter-examples, with the emphasis placed on the key ideas underlying the theory. Much of the content is informed by its applicability: Fourier analysis is developed to the point where it can be rigorously applied to partial differential equations or computation, and the theory of metric spaces includes applications to ordinary differential equations and fractals. Essential Real Analysis will appeal t...

  14. Robust multivariate analysis

    CERN Document Server

    J Olive, David

    2017-01-01

    This text presents methods that are robust to the assumption of a multivariate normal distribution or methods that are robust to certain types of outliers. Instead of using exact theory based on the multivariate normal distribution, the simpler and more applicable large sample theory is given.  The text develops among the first practical robust regression and robust multivariate location and dispersion estimators backed by theory.   The robust techniques  are illustrated for methods such as principal component analysis, canonical correlation analysis, and factor analysis.  A simple way to bootstrap confidence regions is also provided. Much of the research on robust multivariate analysis in this book is being published for the first time. The text is suitable for a first course in Multivariate Statistical Analysis or a first course in Robust Statistics. This graduate text is also useful for people who are familiar with the traditional multivariate topics, but want to know more about handling data sets with...

  15. Data analysis workbench

    International Nuclear Information System (INIS)

    Goetz, A.; Gerring, M.; Svensson, O.; Brockhauser, S.

    2012-01-01

    Data Analysis Workbench (DAWB) is a new software tool being developed at the ESRF. Its goal is to provide a tool for both online data analysis which can be used on the beamlines and for offline data analysis which users can use during experiments or take home. The tool includes support for data visualization and work-flows. work-flows allow algorithms which exploit parallel architectures to be designed from existing high level modules for data analysis in combination with data collection. The workbench uses Passerelle as the work-flow engine and EDNA plug-ins for data analysis. Actors talking to Tango are used for sending commands to a limited set of hardware to start existing data collection algorithms. A Tango server allows work-flows to be executed from existing applications. There are scripting interfaces to Python, Javascript and SPEC. The current state at the ESRF is the workbench is in test on a selected number of beamlines. (authors)

  16. Data-variant kernel analysis

    CERN Document Server

    Motai, Yuichi

    2015-01-01

    Describes and discusses the variants of kernel analysis methods for data types that have been intensely studied in recent years This book covers kernel analysis topics ranging from the fundamental theory of kernel functions to its applications. The book surveys the current status, popular trends, and developments in kernel analysis studies. The author discusses multiple kernel learning algorithms and how to choose the appropriate kernels during the learning phase. Data-Variant Kernel Analysis is a new pattern analysis framework for different types of data configurations. The chapters include

  17. Human reliability analysis

    International Nuclear Information System (INIS)

    Dougherty, E.M.; Fragola, J.R.

    1988-01-01

    The authors present a treatment of human reliability analysis incorporating an introduction to probabilistic risk assessment for nuclear power generating stations. They treat the subject according to the framework established for general systems theory. Draws upon reliability analysis, psychology, human factors engineering, and statistics, integrating elements of these fields within a systems framework. Provides a history of human reliability analysis, and includes examples of the application of the systems approach

  18. Emission spectrochemical analysis

    International Nuclear Information System (INIS)

    Rives, R.D.; Bruks, R.R.

    1983-01-01

    The emission spectrochemical method of analysis based on the fact that atoms of elements can be excited in the electric arc or in the laser beam and will emit radiation with characteristic wave lengths is considered. The review contains the data on spectrochemical analysis, of liquids geological materials, scheme of laser microprobe. The main characteristics of emission spectroscopy, atomic absorption spectroscopy and X-ray fluorescent analysis, are aeneralized

  19. Comparative risk analysis

    International Nuclear Information System (INIS)

    Niehaus, F.

    1988-01-01

    In this paper, the risks of various energy systems are discussed considering severe accidents analysis, particularly the probabilistic safety analysis, and probabilistic safety criteria, and the applications of these criteria and analysis. The comparative risk analysis has demonstrated that the largest source of risk in every society is from daily small accidents. Nevertheless, we have to be more concerned about severe accidents. The comparative risk analysis of five different energy systems (coal, oil, gas, LWR and STEC (Solar)) for the public has shown that the main sources of risks are coal and oil. The latest comparative risk study of various energy has been conducted in the USA and has revealed that the number of victims from coal is 42 as many than victims from nuclear. A study for severe accidents from hydro-dams in United States has estimated the probability of dam failures at 1 in 10,000 years and the number of victims between 11,000 and 260,000. The average occupational risk from coal is one fatal accident in 1,000 workers/year. The probabilistic safety analysis is a method that can be used to assess nuclear energy risks, and to analyze the severe accidents, and to model all possible accident sequences and consequences. The 'Fault tree' analysis is used to know the probability of failure of the different systems at each point of accident sequences and to calculate the probability of risks. After calculating the probability of failure, the criteria for judging the numerical results have to be developed, that is the quantitative and qualitative goals. To achieve these goals, several systems have been devised by various countries members of AIEA. The probabilistic safety ana-lysis method has been developed by establishing a computer program permit-ting to know different categories of safety related information. 19 tabs. (author)

  20. Fault tree analysis

    International Nuclear Information System (INIS)

    1981-09-01

    Suggestion are made concerning the method of the fault tree analysis, the use of certain symbols in the examination of system failures. This purpose of the fault free analysis is to find logical connections of component or subsystem failures leading to undesirable occurrances. The results of these examinations are part of the system assessment concerning operation and safety. The objectives of the analysis are: systematical identification of all possible failure combinations (causes) leading to a specific undesirable occurrance, finding of reliability parameters such as frequency of failure combinations, frequency of the undesirable occurrance or non-availability of the system when required. The fault tree analysis provides a near and reconstructable documentation of the examination. (orig./HP) [de

  1. Social Set Analysis

    DEFF Research Database (Denmark)

    Vatrapu, Ravi; Mukkamala, Raghava Rao; Hussain, Abid

    2016-01-01

    , conceptual and formal models of social data, and an analytical framework for combining big social data sets with organizational and societal data sets. Three empirical studies of big social data are presented to illustrate and demonstrate social set analysis in terms of fuzzy set-theoretical sentiment...... automata and agent-based modeling). However, when it comes to organizational and societal units of analysis, there exists no approach to conceptualize, model, analyze, explain, and predict social media interactions as individuals' associations with ideas, values, identities, and so on. To address...... analysis, crisp set-theoretical interaction analysis, and event-studies-oriented set-theoretical visualizations. Implications for big data analytics, current limitations of the set-theoretical approach, and future directions are outlined....

  2. Hermeneutic phenomenological analysis: the 'possibility' beyond 'actuality' in thematic analysis.

    Science.gov (United States)

    Ho, Ken H M; Chiang, Vico C L; Leung, Doris

    2017-07-01

    This article discusses the ways researchers may become open to manifold interpretations of lived experience through thematic analysis that follows the tradition of hermeneutic phenomenology. Martin Heidegger's thinking about historical contexts of understandings and the notions of 'alētheia' and 'techne' disclose what he called meaning of lived experience, as the 'unchanging Being of changing beings'. While these notions remain central to hermeneutic phenomenological research, novice phenomenologists usually face the problem of how to incorporate these philosophical tenets into thematic analysis. Discussion paper. This discussion paper is based on our experiences of hermeneutic analysis supported by the writings of Heidegger. Literature reviewed for this paper ranges from 1927 - 2014. We draw on data from a study of foreign domestic helpers in Hong Kong to demonstrate how 'dwelling' in the language of participants' 'ek-sistence' supported us in a process of thematic analysis. Data were collected from December 2013 - February 2016. Nurses doing hermeneutic phenomenology have to develop self-awareness of one's own 'taken-for-granted' thinking to disclose the unspoken meanings hidden in the language of participants. Understanding the philosophical tenets of hermeneutic phenomenology allows nurses to preserve possibilities of interpretations in thinking. In so doing, methods of thematic analysis can uncover and present the structure of the meaning of lived experience. We provide our readers with vicarious experience of how to begin cultivating thinking that is aligned with hermeneutic phenomenological philosophical tenets to conduct thematic analysis. © 2017 John Wiley & Sons Ltd.

  3. Physicochemical properties of different corn varieties by principal components analysis and cluster analysis

    International Nuclear Information System (INIS)

    Zeng, J.; Li, G.; Sun, J.

    2013-01-01

    Principal components analysis and cluster analysis were used to investigate the properties of different corn varieties. The chemical compositions and some properties of corn flour which processed by drying milling were determined. The results showed that the chemical compositions and physicochemical properties were significantly different among twenty six corn varieties. The quality of corn flour was concerned with five principal components from principal component analysis and the contribution rate of starch pasting properties was important, which could account for 48.90%. Twenty six corn varieties could be classified into four groups by cluster analysis. The consistency between principal components analysis and cluster analysis indicated that multivariate analyses were feasible in the study of corn variety properties. (author)

  4. Compatibility analysis of DUPIC fuel(4) - thermal hydraulic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jee Won; Chae, Kyung Myung; Choi, Hang Bok

    2000-07-01

    Thermal-hydraulic compatibility of the DUPIC fuel bundle in the CANDU reactor has been studied. The critical channel power, the critical power ratio, the channel exit quality and the channel flow are calculated for the DUPIC and the standard fuels by using the NUCIRC code. The physical models and associated parametric values for the NUCIRC analysis of the fuels are also presented. Based upon the slave channel analysis, the critical channel power and the critical power ratios have been found to be very similar for the two fuel types. The same dryout model is used in this study for the standard and the DUPIC fuel bundles. To assess the dryout characteristics of the DUPIC fuel bundle, the ASSERT-PV code has been used for the subchannel analysis. Based upon the results of the subchannel analysis, it is found that the dryout location and the power for the two fuel types are indeed very similar. This study shows that thermal performance of the DUPIC fuel is not significantly different from that of the standard fuel.

  5. The ATLAS Analysis Model

    CERN Multimedia

    Amir Farbin

    The ATLAS Analysis Model is a continually developing vision of how to reconcile physics analysis requirements with the ATLAS offline software and computing model constraints. In the past year this vision has influenced the evolution of the ATLAS Event Data Model, the Athena software framework, and physics analysis tools. These developments, along with the October Analysis Model Workshop and the planning for CSC analyses have led to a rapid refinement of the ATLAS Analysis Model in the past few months. This article introduces some of the relevant issues and presents the current vision of the future ATLAS Analysis Model. Event Data Model The ATLAS Event Data Model (EDM) consists of several levels of details, each targeted for a specific set of tasks. For example the Event Summary Data (ESD) stores calorimeter cells and tracking system hits thereby permitting many calibration and alignment tasks, but will be only accessible at particular computing sites with potentially large latency. In contrast, the Analysis...

  6. Hazard Analysis Database Report

    Energy Technology Data Exchange (ETDEWEB)

    GAULT, G.W.

    1999-10-13

    The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR). The FSAR is part of the approved TWRS Authorization Basis (AB). This document describes, identifies, and defines the contents and structure of the TWRS FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The TWRS Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The database supports the preparation of Chapters 3,4, and 5 of the TWRS FSAR and the USQ process and consists of two major, interrelated data sets: (1) Hazard Evaluation Database--Data from the results of the hazard evaluations; and (2) Hazard Topography Database--Data from the system familiarization and hazard identification.

  7. A sensory analysis of butter cookies: An application of generalized procrustes analysis

    OpenAIRE

    Juhl, Hans Jørn

    1994-01-01

    Executive Summary: 1. A sensory analysis is one of the first steps in product development in the food industry. A thorough analysis of the results from such an analysis may give important input to the development process. 2. A sensory analysis on butter cookies is conducted in order to evaluate if some butter may be replaced by vegetable fat without a significant change in the sensory profile. The conclusion is that the replacement is possible without a considerable change in the sensory prof...

  8. Data analysis and approximate models model choice, location-scale, analysis of variance, nonparametric regression and image analysis

    CERN Document Server

    Davies, Patrick Laurie

    2014-01-01

    Introduction IntroductionApproximate Models Notation Two Modes of Statistical AnalysisTowards One Mode of Analysis Approximation, Randomness, Chaos, Determinism ApproximationA Concept of Approximation Approximation Approximating a Data Set by a Model Approximation Regions Functionals and EquivarianceRegularization and Optimality Metrics and DiscrepanciesStrong and Weak Topologies On Being (almost) Honest Simulations and Tables Degree of Approximation and p-values ScalesStability of Analysis The Choice of En(α, P) Independence Procedures, Approximation and VaguenessDiscrete Models The Empirical Density Metrics and Discrepancies The Total Variation Metric The Kullback-Leibler and Chi-Squared Discrepancies The Po(λ) ModelThe b(k, p) and nb(k, p) Models The Flying Bomb Data The Student Study Times Data OutliersOutliers, Data Analysis and Models Breakdown Points and Equivariance Identifying Outliers and Breakdown Outliers in Multivariate Data Outliers in Linear Regression Outliers in Structured Data The Location...

  9. Frontier Assignment for Sensitivity Analysis of Data Envelopment Analysis

    Science.gov (United States)

    Naito, Akio; Aoki, Shingo; Tsuji, Hiroshi

    To extend the sensitivity analysis capability for DEA (Data Envelopment Analysis), this paper proposes frontier assignment based DEA (FA-DEA). The basic idea of FA-DEA is to allow a decision maker to decide frontier intentionally while the traditional DEA and Super-DEA decide frontier computationally. The features of FA-DEA are as follows: (1) provides chances to exclude extra-influential DMU (Decision Making Unit) and finds extra-ordinal DMU, and (2) includes the function of the traditional DEA and Super-DEA so that it is able to deal with sensitivity analysis more flexibly. Simple numerical study has shown the effectiveness of the proposed FA-DEA and the difference from the traditional DEA.

  10. Overview of methods for uncertainty analysis and sensitivity analysis in probabilistic risk assessment

    International Nuclear Information System (INIS)

    Iman, R.L.; Helton, J.C.

    1985-01-01

    Probabilistic Risk Assessment (PRA) is playing an increasingly important role in the nuclear reactor regulatory process. The assessment of uncertainties associated with PRA results is widely recognized as an important part of the analysis process. One of the major criticisms of the Reactor Safety Study was that its representation of uncertainty was inadequate. The desire for the capability to treat uncertainties with the MELCOR risk code being developed at Sandia National Laboratories is indicative of the current interest in this topic. However, as yet, uncertainty analysis and sensitivity analysis in the context of PRA is a relatively immature field. In this paper, available methods for uncertainty analysis and sensitivity analysis in a PRA are reviewed. This review first treats methods for use with individual components of a PRA and then considers how these methods could be combined in the performance of a complete PRA. In the context of this paper, the goal of uncertainty analysis is to measure the imprecision in PRA outcomes of interest, and the goal of sensitivity analysis is to identify the major contributors to this imprecision. There are a number of areas that must be considered in uncertainty analysis and sensitivity analysis for a PRA: (1) information, (2) systems analysis, (3) thermal-hydraulic phenomena/fission product behavior, (4) health and economic consequences, and (5) display of results. Each of these areas and the synthesis of them into a complete PRA are discussed

  11. Meta-Analysis for Primary and Secondary Data Analysis: The Super-Experiment Metaphor.

    Science.gov (United States)

    Jackson, Sally

    1991-01-01

    Considers the relation between meta-analysis statistics and analysis of variance statistics. Discusses advantages and disadvantages as a primary data analysis tool. Argues that the two approaches are partial paraphrases of one another. Advocates an integrative approach that introduces the best of meta-analytic thinking into primary analysis…

  12. Canonical Information Analysis

    DEFF Research Database (Denmark)

    Vestergaard, Jacob Schack; Nielsen, Allan Aasbjerg

    2015-01-01

    is replaced by the information theoretical, entropy based measure mutual information, which is a much more general measure of association. We make canonical information analysis feasible for large sample problems, including for example multispectral images, due to the use of a fast kernel density estimator......Canonical correlation analysis is an established multivariate statistical method in which correlation between linear combinations of multivariate sets of variables is maximized. In canonical information analysis introduced here, linear correlation as a measure of association between variables...... for entropy estimation. Canonical information analysis is applied successfully to (1) simple simulated data to illustrate the basic idea and evaluate performance, (2) fusion of weather radar and optical geostationary satellite data in a situation with heavy precipitation, and (3) change detection in optical...

  13. Biorefinery Sustainability Analysis

    DEFF Research Database (Denmark)

    J. S. M. Silva, Carla; Prunescu, Remus Mihail; Gernaey, Krist

    2017-01-01

    This chapter deals with sustainability analysis of biorefinery systems in terms of environmental and socio-economic indicators . Life cycle analysis has methodological issues related to the functional unit (FU), allocation , land use and biogenic carbon neutrality of the reference system and of t......This chapter deals with sustainability analysis of biorefinery systems in terms of environmental and socio-economic indicators . Life cycle analysis has methodological issues related to the functional unit (FU), allocation , land use and biogenic carbon neutrality of the reference system...... and of the biorefinery-based system. Socio-economic criteria and indicators used in sustainability frameworks assessment are presented and discussed. There is not one single methodology that can aptly cover the synergies of environmental, economic, social and governance issues required to assess the sustainable...

  14. Application of optical deformation analysis system on wedge splitting test and its inverse analysis

    DEFF Research Database (Denmark)

    Skocek, Jan; Stang, Henrik

    2010-01-01

    . Results of the inverse analysis are compared with traditional inverse analysis based on clip gauge data. Then the optically measured crack profile and crack tip position are compared with predictions done by the non-linear hinge model and a finite element analysis. It is shown that the inverse analysis...... based on the optically measured data can provide material parameters of the fictitious crack model matching favorably those obtained by classical inverse analysis based on the clip gauge data. Further advantages of using of the optical deformation analysis lie in identification of such effects...

  15. Handbook of Applied Analysis

    CERN Document Server

    Papageorgiou, Nikolaos S

    2009-01-01

    Offers an examination of important theoretical methods and procedures in applied analysis. This book details the important theoretical trends in nonlinear analysis and applications to different fields. It is suitable for those working on nonlinear analysis.

  16. How Content Analysis may Complement and Extend the Insights of Discourse Analysis

    Directory of Open Access Journals (Sweden)

    Tracey Feltham-King

    2016-02-01

    Full Text Available Although discourse analysis is a well-established qualitative research methodology, little attention has been paid to how discourse analysis may be enhanced through careful supplementation with the quantification allowed in content analysis. In this article, we report on a research study that involved the use of both Foucauldian discourse analysis (FDA and directed content analysis based on social constructionist theory and our qualitative research findings. The research focused on the discourses deployed, and the ways in which women were discursively positioned, in relation to abortion in 300 newspaper articles, published in 25 national and regional South African newspapers over 28 years, from 1978 to 2005. While the FDA was able to illuminate the constitutive network of power relations constructing women as subjects of a particular kind, questions emerged that were beyond the scope of the FDA. These questions concerned understanding the relative weightings of various discourses and tracing historical changes in the deployment of these discourses. In this article, we show how the decision to combine FDA and content analysis affected our sampling methodology. Using specific examples, we illustrate the contribution of the FDA to the study. Then, we indicate how subject positioning formed the link between the FDA and the content analysis. Drawing on the same examples, we demonstrate how the content analysis supplemented the FDA through tracking changes over time and providing empirical evidence of the extent to which subject positionings were deployed.

  17. Abstract interfaces for data analysis - component architecture for data analysis tools

    International Nuclear Information System (INIS)

    Barrand, G.; Binko, P.; Doenszelmann, M.; Pfeiffer, A.; Johnson, A.

    2001-01-01

    The fast turnover of software technologies, in particular in the domain of interactivity (covering user interface and visualisation), makes it difficult for a small group of people to produce complete and polished software-tools before the underlying technologies make them obsolete. At the HepVis'99 workshop, a working group has been formed to improve the production of software tools for data analysis in HENP. Beside promoting a distributed development organisation, one goal of the group is to systematically design a set of abstract interfaces based on using modern OO analysis and OO design techniques. An initial domain analysis has come up with several categories (components) found in typical data analysis tools: Histograms, Ntuples, Functions, Vectors, Fitter, Plotter, analyzer and Controller. Special emphasis was put on reducing the couplings between the categories to a minimum, thus optimising re-use and maintainability of any component individually. The interfaces have been defined in Java and C++ and implementations exist in the form of libraries and tools using C++ (Anaphe/Lizard, OpenScientist) and Java (Java Analysis Studio). A special implementation aims at accessing the Java libraries (through their Abstract Interfaces) from C++. The authors give an overview of the architecture and design of the various components for data analysis as discussed in AIDA

  18. LULU analysis program

    International Nuclear Information System (INIS)

    Crawford, H.J.; Lindstrom, P.J.

    1983-06-01

    Our analysis program LULU has proven very useful in all stages of experiment analysis, from prerun detector debugging through final data reduction. It has solved our problem of having arbitrary word length events and is easy enough to use that many separate experimenters are now analyzing with LULU. The ability to use the same software for all stages of experiment analysis greatly eases the programming burden. We may even get around to making the graphics elegant someday

  19. Stochastic Analysis 2010

    CERN Document Server

    Crisan, Dan

    2011-01-01

    "Stochastic Analysis" aims to provide mathematical tools to describe and model high dimensional random systems. Such tools arise in the study of Stochastic Differential Equations and Stochastic Partial Differential Equations, Infinite Dimensional Stochastic Geometry, Random Media and Interacting Particle Systems, Super-processes, Stochastic Filtering, Mathematical Finance, etc. Stochastic Analysis has emerged as a core area of late 20th century Mathematics and is currently undergoing a rapid scientific development. The special volume "Stochastic Analysis 2010" provides a sa

  20. Ecosystem Analysis Program

    International Nuclear Information System (INIS)

    Burgess, R.L.

    1978-01-01

    Progress is reported on the following research programs: analysis and modeling of ecosystems; EDFB/IBP data center; biome analysis studies; land/water interaction studies; and computer programs for development of models

  1. Trend analysis

    International Nuclear Information System (INIS)

    Smith, M.; Jones, D.R.

    1991-01-01

    The goal of exploration is to find reserves that will earn an adequate rate of return on the capital invested. Neither exploration nor economics is an exact science. The authors must therefore explore in those trends (plays) that have the highest probability of achieving this goal. Trend analysis is a technique for organizing the available data to make these strategic exploration decisions objectively and is in conformance with their goals and risk attitudes. Trend analysis differs from resource estimation in its purpose. It seeks to determine the probability of economic success for an exploration program, not the ultimate results of the total industry effort. Thus the recent past is assumed to be the best estimate of the exploration probabilities for the near future. This information is combined with economic forecasts. The computer software tools necessary for trend analysis are (1) Information data base - requirements and sources. (2) Data conditioning program - assignment to trends, correction of errors, and conversion into usable form. (3) Statistical processing program - calculation of probability of success and discovery size probability distribution. (4) Analytical processing - Monte Carlo simulation to develop the probability distribution of the economic return/investment ratio for a trend. Limited capital (short-run) effects are analyzed using the Gambler's Ruin concept in the Monte Carlo simulation and by a short-cut method. Multiple trend analysis is concerned with comparing and ranking trends, allocating funds among acceptable trends, and characterizing program risk by using risk profiles. In summary, trend analysis is a reality check for long-range exploration planning

  2. Radiation analysis devices, radiation analysis methods, and articles of manufacture

    Science.gov (United States)

    Roybal, Lyle Gene

    2010-06-08

    Radiation analysis devices include circuitry configured to determine respective radiation count data for a plurality of sections of an area of interest and combine the radiation count data of individual of sections to determine whether a selected radioactive material is present in the area of interest. An amount of the radiation count data for an individual section is insufficient to determine whether the selected radioactive material is present in the individual section. An article of manufacture includes media comprising programming configured to cause processing circuitry to perform processing comprising determining one or more correction factors based on a calibration of a radiation analysis device, measuring radiation received by the radiation analysis device using the one or more correction factors, and presenting information relating to an amount of radiation measured by the radiation analysis device having one of a plurality of specified radiation energy levels of a range of interest.

  3. Incorporation of advanced accident analysis methodology into safety analysis reports

    International Nuclear Information System (INIS)

    2003-05-01

    The IAEA Safety Guide on Safety Assessment and Verification defines that the aim of the safety analysis should be by means of appropriate analytical tools to establish and confirm the design basis for the items important to safety, and to ensure that the overall plant design is capable of meeting the prescribed and acceptable limits for radiation doses and releases for each plant condition category. Practical guidance on how to perform accident analyses of nuclear power plants (NPPs) is provided by the IAEA Safety Report on Accident Analysis for Nuclear Power Plants. The safety analyses are performed both in the form of deterministic and probabilistic analyses for NPPs. It is customary to refer to deterministic safety analyses as accident analyses. This report discusses the aspects of using the advanced accident analysis methods to carry out accident analyses in order to introduce them into the Safety Analysis Reports (SARs). In relation to the SAR, purposes of deterministic safety analysis can be further specified as (1) to demonstrate compliance with specific regulatory acceptance criteria; (2) to complement other analyses and evaluations in defining a complete set of design and operating requirements; (3) to identify and quantify limiting safety system set points and limiting conditions for operation to be used in the NPP limits and conditions; (4) to justify appropriateness of the technical solutions employed in the fulfillment of predetermined safety requirements. The essential parts of accident analyses are performed by applying sophisticated computer code packages, which have been specifically developed for this purpose. These code packages include mainly thermal-hydraulic system codes and reactor dynamics codes meant for the transient and accident analyses. There are also specific codes such as those for the containment thermal-hydraulics, for the radiological consequences and for severe accident analyses. In some cases, codes of a more general nature such

  4. Professionalizing Intelligence Analysis

    Directory of Open Access Journals (Sweden)

    James B. Bruce

    2015-09-01

    Full Text Available This article examines the current state of professionalism in national security intelligence analysis in the U.S. Government. Since the introduction of major intelligence reforms directed by the Intelligence Reform and Terrorism Prevention Act (IRTPA in December, 2004, we have seen notable strides in many aspects of intelligence professionalization, including in analysis. But progress is halting, uneven, and by no means permanent. To consolidate its gains, and if it is to continue improving, the U.S. intelligence community (IC should commit itself to accomplishing a new program of further professionalization of analysis to ensure that it will develop an analytic cadre that is fully prepared to deal with the complexities of an emerging multipolar and highly dynamic world that the IC itself is forecasting. Some recent reforms in intelligence analysis can be assessed against established standards of more fully developed professions; these may well fall short of moving the IC closer to the more fully professionalized analytical capability required for producing the kind of analysis needed now by the United States.

  5. Dynamic Chest Image Analysis: Model-Based Perfusion Analysis in Dynamic Pulmonary Imaging

    Directory of Open Access Journals (Sweden)

    Kiuru Aaro

    2003-01-01

    Full Text Available The "Dynamic Chest Image Analysis" project aims to develop model-based computer analysis and visualization methods for showing focal and general abnormalities of lung ventilation and perfusion based on a sequence of digital chest fluoroscopy frames collected with the dynamic pulmonary imaging technique. We have proposed and evaluated a multiresolutional method with an explicit ventilation model for ventilation analysis. This paper presents a new model-based method for pulmonary perfusion analysis. According to perfusion properties, we first devise a novel mathematical function to form a perfusion model. A simple yet accurate approach is further introduced to extract cardiac systolic and diastolic phases from the heart, so that this cardiac information may be utilized to accelerate the perfusion analysis and improve its sensitivity in detecting pulmonary perfusion abnormalities. This makes perfusion analysis not only fast but also robust in computation; consequently, perfusion analysis becomes computationally feasible without using contrast media. Our clinical case studies with 52 patients show that this technique is effective for pulmonary embolism even without using contrast media, demonstrating consistent correlations with computed tomography (CT and nuclear medicine (NM studies. This fluoroscopical examination takes only about 2 seconds for perfusion study with only low radiation dose to patient, involving no preparation, no radioactive isotopes, and no contrast media.

  6. Electronic Circuit Analysis Language (ECAL)

    Science.gov (United States)

    Chenghang, C.

    1983-03-01

    The computer aided design technique is an important development in computer applications and it is an important component of computer science. The special language for electronic circuit analysis is the foundation of computer aided design or computer aided circuit analysis (abbreviated as CACD and CACA) of simulated circuits. Electronic circuit analysis language (ECAL) is a comparatively simple and easy to use circuit analysis special language which uses the FORTRAN language to carry out the explanatory executions. It is capable of conducting dc analysis, ac analysis, and transient analysis of a circuit. Futhermore, the results of the dc analysis can be used directly as the initial conditions for the ac and transient analyses.

  7. NeoAnalysis: a Python-based toolbox for quick electrophysiological data processing and analysis.

    Science.gov (United States)

    Zhang, Bo; Dai, Ji; Zhang, Tao

    2017-11-13

    In a typical electrophysiological experiment, especially one that includes studying animal behavior, the data collected normally contain spikes, local field potentials, behavioral responses and other associated data. In order to obtain informative results, the data must be analyzed simultaneously with the experimental settings. However, most open-source toolboxes currently available for data analysis were developed to handle only a portion of the data and did not take into account the sorting of experimental conditions. Additionally, these toolboxes require that the input data be in a specific format, which can be inconvenient to users. Therefore, the development of a highly integrated toolbox that can process multiple types of data regardless of input data format and perform basic analysis for general electrophysiological experiments is incredibly useful. Here, we report the development of a Python based open-source toolbox, referred to as NeoAnalysis, to be used for quick electrophysiological data processing and analysis. The toolbox can import data from different data acquisition systems regardless of their formats and automatically combine different types of data into a single file with a standardized format. In cases where additional spike sorting is needed, NeoAnalysis provides a module to perform efficient offline sorting with a user-friendly interface. Then, NeoAnalysis can perform regular analog signal processing, spike train, and local field potentials analysis, behavioral response (e.g. saccade) detection and extraction, with several options available for data plotting and statistics. Particularly, it can automatically generate sorted results without requiring users to manually sort data beforehand. In addition, NeoAnalysis can organize all of the relevant data into an informative table on a trial-by-trial basis for data visualization. Finally, NeoAnalysis supports analysis at the population level. With the multitude of general-purpose functions provided

  8. Bearing defect signature analysis using advanced nonlinear signal analysis in a controlled environment

    Science.gov (United States)

    Zoladz, T.; Earhart, E.; Fiorucci, T.

    1995-01-01

    Utilizing high-frequency data from a highly instrumented rotor assembly, seeded bearing defect signatures are characterized using both conventional linear approaches, such as power spectral density analysis, and recently developed nonlinear techniques such as bicoherence analysis. Traditional low-frequency (less than 20 kHz) analysis and high-frequency envelope analysis of both accelerometer and acoustic emission data are used to recover characteristic bearing distress information buried deeply in acquired data. The successful coupling of newly developed nonlinear signal analysis with recovered wideband envelope data from accelerometers and acoustic emission sensors is the innovative focus of this research.

  9. New trends in applied harmonic analysis sparse representations, compressed sensing, and multifractal analysis

    CERN Document Server

    Cabrelli, Carlos; Jaffard, Stephane; Molter, Ursula

    2016-01-01

    This volume is a selection of written notes corresponding to courses taught at the CIMPA School: "New Trends in Applied Harmonic Analysis: Sparse Representations, Compressed Sensing and Multifractal Analysis". New interactions between harmonic analysis and signal and image processing have seen striking development in the last 10 years, and several technological deadlocks have been solved through the resolution of deep theoretical problems in harmonic analysis. New Trends in Applied Harmonic Analysis focuses on two particularly active areas that are representative of such advances: multifractal analysis, and sparse representation and compressed sensing. The contributions are written by leaders in these areas, and covers both theoretical aspects and applications. This work should prove useful not only to PhD students and postdocs in mathematics and signal and image processing, but also to researchers working in related topics.

  10. Introductory numerical analysis

    CERN Document Server

    Pettofrezzo, Anthony J

    2006-01-01

    Written for undergraduates who require a familiarity with the principles behind numerical analysis, this classical treatment encompasses finite differences, least squares theory, and harmonic analysis. Over 70 examples and 280 exercises. 1967 edition.

  11. Regression analysis by example

    CERN Document Server

    Chatterjee, Samprit

    2012-01-01

    Praise for the Fourth Edition: ""This book is . . . an excellent source of examples for regression analysis. It has been and still is readily readable and understandable."" -Journal of the American Statistical Association Regression analysis is a conceptually simple method for investigating relationships among variables. Carrying out a successful application of regression analysis, however, requires a balance of theoretical results, empirical rules, and subjective judgment. Regression Analysis by Example, Fifth Edition has been expanded

  12. A novel bi-level meta-analysis approach: applied to biological pathway analysis.

    Science.gov (United States)

    Nguyen, Tin; Tagett, Rebecca; Donato, Michele; Mitrea, Cristina; Draghici, Sorin

    2016-02-01

    The accumulation of high-throughput data in public repositories creates a pressing need for integrative analysis of multiple datasets from independent experiments. However, study heterogeneity, study bias, outliers and the lack of power of available methods present real challenge in integrating genomic data. One practical drawback of many P-value-based meta-analysis methods, including Fisher's, Stouffer's, minP and maxP, is that they are sensitive to outliers. Another drawback is that, because they perform just one statistical test for each individual experiment, they may not fully exploit the potentially large number of samples within each study. We propose a novel bi-level meta-analysis approach that employs the additive method and the Central Limit Theorem within each individual experiment and also across multiple experiments. We prove that the bi-level framework is robust against bias, less sensitive to outliers than other methods, and more sensitive to small changes in signal. For comparative analysis, we demonstrate that the intra-experiment analysis has more power than the equivalent statistical test performed on a single large experiment. For pathway analysis, we compare the proposed framework versus classical meta-analysis approaches (Fisher's, Stouffer's and the additive method) as well as against a dedicated pathway meta-analysis package (MetaPath), using 1252 samples from 21 datasets related to three human diseases, acute myeloid leukemia (9 datasets), type II diabetes (5 datasets) and Alzheimer's disease (7 datasets). Our framework outperforms its competitors to correctly identify pathways relevant to the phenotypes. The framework is sufficiently general to be applied to any type of statistical meta-analysis. The R scripts are available on demand from the authors. sorin@wayne.edu Supplementary data are available at Bioinformatics online. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e

  13. Synovial fluid analysis

    Science.gov (United States)

    Joint fluid analysis; Joint fluid aspiration ... El-Gabalawy HS. Synovial fluid analysis, synovial biopsy, and synovial pathology. In: Firestein GS, Budd RC, Gabriel SE, McInnes IB, O'Dell JR, eds. Kelly's Textbook of ...

  14. Study on mixed analysis method for fatigue analysis of oblique safety injection nozzle on main piping

    International Nuclear Information System (INIS)

    Lu Xifeng; Zhang Yixiong; Ai Honglei; Wang Xinjun; He Feng

    2014-01-01

    The simplified analysis method and the detailed analysis method were used for the fatigue analysis of the nozzle on the main piping. Because the structure of the oblique safety injection nozzle is complex and some more severe transients are subjected. The results obtained are more penalized and cannot be validate when the simplified analysis method used for the fatigue analysis. It will be little conservative when the detailed analysis method used, but it is more complex and time-consuming and boring labor. To reduce the conservatism and save time, the mixed analysis method which combining the simplified analysis method with the detailed analysis method is used for the fatigue analysis. The heat transfer parameters between the fluid and the structure which used for analysis were obtained by heat transfer property experiment. The results show that the mixed analysis which heat transfer property is considered can reduce the conservatism effectively, and the mixed analysis method is a more effective and practical method used for the fatigue analysis of the oblique safety injection nozzle. (authors)

  15. Factor analysis

    CERN Document Server

    Gorsuch, Richard L

    2013-01-01

    Comprehensive and comprehensible, this classic covers the basic and advanced topics essential for using factor analysis as a scientific tool in psychology, education, sociology, and related areas. Emphasizing the usefulness of the techniques, it presents sufficient mathematical background for understanding and sufficient discussion of applications for effective use. This includes not only theory but also the empirical evaluations of the importance of mathematical distinctions for applied scientific analysis.

  16. Cask crush pad analysis using detailed and simplified analysis methods

    International Nuclear Information System (INIS)

    Uldrich, E.D.; Hawkes, B.D.

    1997-01-01

    A crush pad has been designed and analyzed to absorb the kinetic energy of a hypothetically dropped spent nuclear fuel shipping cask into a 44-ft. deep cask unloading pool at the Fluorinel and Storage Facility (FAST). This facility, located at the Idaho Chemical Processing Plant (ICPP) at the Idaho national Engineering and Environmental Laboratory (INEEL), is a US Department of Energy site. The basis for this study is an analysis by Uldrich and Hawkes. The purpose of this analysis was to evaluate various hypothetical cask drop orientations to ensure that the crush pad design was adequate and the cask deceleration at impact was less than 100 g. It is demonstrated herein that a large spent fuel shipping cask, when dropped onto a foam crush pad, can be analyzed by either hand methods or by sophisticated dynamic finite element analysis using computer codes such as ABAQUS. Results from the two methods are compared to evaluate accuracy of the simplified hand analysis approach

  17. Plug-in Based Analysis Framework for LHC Post-Mortem Analysis

    CERN Document Server

    Gorbonosov, R; Zerlauth, M; Baggiolini, V

    2014-01-01

    Plug-in based software architectures [1] are extensible, enforce modularity and allow several teams to work in parallel. But they have certain technical and organizational challenges, which we discuss in this paper. We gained our experience when developing the Post-Mortem Analysis (PMA) system, which is a mission critical system for the Large Hadron Collider (LHC). We used a plugin-based architecture with a general-purpose analysis engine, for which physicists and equipment experts code plugins containing the analysis algorithms. We have over 45 analysis plugins developed by a dozen of domain experts. This paper focuses on the design challenges we faced in order to mitigate the risks of executing third-party code: assurance that even a badly written plugin doesn't perturb the work of the overall application; plugin execution control which allows to detect plugin misbehaviour and react; robust communication mechanism between plugins, diagnostics facilitation in case of plugin failure; testing of the plugins be...

  18. Functional analysis and applications

    CERN Document Server

    Siddiqi, Abul Hasan

    2018-01-01

    This self-contained textbook discusses all major topics in functional analysis. Combining classical materials with new methods, it supplies numerous relevant solved examples and problems and discusses the applications of functional analysis in diverse fields. The book is unique in its scope, and a variety of applications of functional analysis and operator-theoretic methods are devoted to each area of application. Each chapter includes a set of problems, some of which are routine and elementary, and some of which are more advanced. The book is primarily intended as a textbook for graduate and advanced undergraduate students in applied mathematics and engineering. It offers several attractive features making it ideally suited for courses on functional analysis intended to provide a basic introduction to the subject and the impact of functional analysis on applied and computational mathematics, nonlinear functional analysis and optimization. It introduces emerging topics like wavelets, Gabor system, inverse pro...

  19. Easy instrumental analysis

    International Nuclear Information System (INIS)

    Ko, Myeong Su; Kim, Tae Hwa; Park, Gyu Hyeon; Yang, Jong Beom; Oh, Chang Hwan; Lee, Kyoung Hye

    2010-04-01

    This textbook describes instrument analysis in easy way with twelve chapters. The contents of the book are pH measurement on principle, pH meter, pH measurement, examples of the experiments, centrifugation, Absorptiometry, Fluorescent method, Atomic absorption analysis, Gas-chromatography, Gas chromatography-mass spectrometry, High performance liquid chromatography liquid chromatograph-mass spectrometry, Electrophoresis on practical case and analysis of the result and examples, PCR on principle, device, application and examples and Enzyme-linked immunosorbent assay with indirect ELISA, sandwich ELISA and ELISA reader.

  20. Easy instrumental analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Myeong Su; Kim, Tae Hwa; Park, Gyu Hyeon; Yang, Jong Beom; Oh, Chang Hwan; Lee, Kyoung Hye

    2010-04-15

    This textbook describes instrument analysis in easy way with twelve chapters. The contents of the book are pH measurement on principle, pH meter, pH measurement, examples of the experiments, centrifugation, Absorptiometry, Fluorescent method, Atomic absorption analysis, Gas-chromatography, Gas chromatography-mass spectrometry, High performance liquid chromatography liquid chromatograph-mass spectrometry, Electrophoresis on practical case and analysis of the result and examples, PCR on principle, device, application and examples and Enzyme-linked immunosorbent assay with indirect ELISA, sandwich ELISA and ELISA reader.

  1. Fundamentals of PIXE analysis

    International Nuclear Information System (INIS)

    Ishii, Keizo

    1997-01-01

    Elemental analysis based on the particle induced x-ray emission (PIXE) is a novel technique to analyze trace elements. It is a very simple method, its sensitivity is very high, multiple elements in a sample can be simultaneously analyzed and a few 10 μg of a sample is enough to be analyzed. Owing to these characteristics, the PIXE analysis is now used in many fields (e.g. biology, medicine, dentistry, environmental pollution, archaeology, culture assets etc.). Fundamentals of the PIXE analysis are described here: the production of characteristic x-rays and inner shell ionization by heavy charged particles, the continuous background in PIXE spectrum, quantitative formulae of the PIXE analysis, the detection limit of PIXE analysis, etc. (author)

  2. msBiodat analysis tool, big data analysis for high-throughput experiments.

    Science.gov (United States)

    Muñoz-Torres, Pau M; Rokć, Filip; Belužic, Robert; Grbeša, Ivana; Vugrek, Oliver

    2016-01-01

    Mass spectrometry (MS) are a group of a high-throughput techniques used to increase knowledge about biomolecules. They produce a large amount of data which is presented as a list of hundreds or thousands of proteins. Filtering those data efficiently is the first step for extracting biologically relevant information. The filtering may increase interest by merging previous data with the data obtained from public databases, resulting in an accurate list of proteins which meet the predetermined conditions. In this article we present msBiodat Analysis Tool, a web-based application thought to approach proteomics to the big data analysis. With this tool, researchers can easily select the most relevant information from their MS experiments using an easy-to-use web interface. An interesting feature of msBiodat analysis tool is the possibility of selecting proteins by its annotation on Gene Ontology using its Gene Id, ensembl or UniProt codes. The msBiodat analysis tool is a web-based application that allows researchers with any programming experience to deal with efficient database querying advantages. Its versatility and user-friendly interface makes easy to perform fast and accurate data screening by using complex queries. Once the analysis is finished, the result is delivered by e-mail. msBiodat analysis tool is freely available at http://msbiodata.irb.hr.

  3. Instrumental neutron activation analysis as a routine method for rock analysis

    International Nuclear Information System (INIS)

    Rosenberg, R.J.

    1977-06-01

    Instrumental neutron activation methods for the analysis of geological samples have been developed. Special emphasis has been laid on the improvement of sensitivity and accuracy in order to maximize tha quality of the analyses. Furthermore, the procedures have been automated as far as possible in order to minimize the cost of the analysis. A short review of the basic literature is given followed by a description of the principles of the method. All aspects concerning the sensitivity are discussed thoroughly in view of the analyst's possibility of influencing them. Experimentally determined detection limits for Na, Al, K, Ca, Sc, Cr, Ti, V, Mn, Fe, Ni, Co, Rb, Zr, Sb, Cs, Ba, La, Ce, Nd, Sm, Eu, Gd, Tb, Dy, Yb, Lu, Hf, Ta, Th and U are given. The errors of the method are discussed followed by actions taken to avoid them. The most significant error was caused by flux deviation, but this was avoided by building a rotating sample holder for rotating the samples during irradiation. A scheme for the INAA of 32 elements is proposed. The method has been automated as far as possible and an automatic γ-spectrometer and a computer program for the automatic calculation of the results are described. Furthermore, a completely automated uranium analyzer based on delayed neutron counting is described. The methods are discussed in view of their applicability to rock analysis. It is stated that the sensitivity varies considerably from element to element and instrumental activation analysis is an excellent method for the analysis of some specific elements like lanthanides, thorium and uranium but less so for many other elements. The accuracy is good varying from 2% to 10% for most elements. Instrumental activation analysis for most elements is rather an expensive method there being, however, a few exceptions. The most important of these is uranium. The analysis of uranium by delayed neutron counting is an inexpensive means for the analysis of large numbers of samples needed for

  4. Numerical analysis

    CERN Document Server

    Rao, G Shanker

    2006-01-01

    About the Book: This book provides an introduction to Numerical Analysis for the students of Mathematics and Engineering. The book is designed in accordance with the common core syllabus of Numerical Analysis of Universities of Andhra Pradesh and also the syllabus prescribed in most of the Indian Universities. Salient features: Approximate and Numerical Solutions of Algebraic and Transcendental Equation Interpolation of Functions Numerical Differentiation and Integration and Numerical Solution of Ordinary Differential Equations The last three chapters deal with Curve Fitting, Eigen Values and Eigen Vectors of a Matrix and Regression Analysis. Each chapter is supplemented with a number of worked-out examples as well as number of problems to be solved by the students. This would help in the better understanding of the subject. Contents: Errors Solution of Algebraic and Transcendental Equations Finite Differences Interpolation with Equal Intervals Interpolation with Unequal Int...

  5. Wind energy analysis system

    OpenAIRE

    2014-01-01

    M.Ing. (Electrical & Electronic Engineering) One of the most important steps to be taken before a site is to be selected for the extraction of wind energy is the analysis of the energy within the wind on that particular site. No wind energy analysis system exists for the measurement and analysis of wind power. This dissertation documents the design and development of a Wind Energy Analysis System (WEAS). Using a micro-controller based design in conjunction with sensors, WEAS measure, calcu...

  6. Discourse analysis and Foucault's

    Directory of Open Access Journals (Sweden)

    Jansen I.

    2008-01-01

    Full Text Available Discourse analysis is a method with up to now was less recognized in nursing science, althoughmore recently nursing scientists are discovering it for their purposes. However, several authors have criticized thatdiscourse analysis is often misinterpreted because of a lack of understanding of its theoretical backgrounds. In thisarticle, I reconstruct Foucault’s writings in his “Archaeology of Knowledge” to provide a theoretical base for futurearchaeological discourse analysis, which can be categorized as a socio-linguistic discourse analysis.

  7. Slice hyperholomorphic Schur analysis

    CERN Document Server

    Alpay, Daniel; Sabadini, Irene

    2016-01-01

    This book defines and examines the counterpart of Schur functions and Schur analysis in the slice hyperholomorphic setting. It is organized into three parts: the first introduces readers to classical Schur analysis, while the second offers background material on quaternions, slice hyperholomorphic functions, and quaternionic functional analysis. The third part represents the core of the book and explores quaternionic Schur analysis and its various applications. The book includes previously unpublished results and provides the basis for new directions of research.

  8. Sensitivity and uncertainty analysis

    CERN Document Server

    Cacuci, Dan G; Navon, Ionel Michael

    2005-01-01

    As computer-assisted modeling and analysis of physical processes have continued to grow and diversify, sensitivity and uncertainty analyses have become indispensable scientific tools. Sensitivity and Uncertainty Analysis. Volume I: Theory focused on the mathematical underpinnings of two important methods for such analyses: the Adjoint Sensitivity Analysis Procedure and the Global Adjoint Sensitivity Analysis Procedure. This volume concentrates on the practical aspects of performing these analyses for large-scale systems. The applications addressed include two-phase flow problems, a radiative c

  9. WHAT IF (Sensitivity Analysis

    Directory of Open Access Journals (Sweden)

    Iulian N. BUJOREANU

    2011-01-01

    Full Text Available Sensitivity analysis represents such a well known and deeply analyzed subject that anyone to enter the field feels like not being able to add anything new. Still, there are so many facets to be taken into consideration.The paper introduces the reader to the various ways sensitivity analysis is implemented and the reasons for which it has to be implemented in most analyses in the decision making processes. Risk analysis is of outmost importance in dealing with resource allocation and is presented at the beginning of the paper as the initial cause to implement sensitivity analysis. Different views and approaches are added during the discussion about sensitivity analysis so that the reader develops an as thoroughly as possible opinion on the use and UTILITY of the sensitivity analysis. Finally, a round-up conclusion brings us to the question of the possibility of generating the future and analyzing it before it unfolds so that, when it happens it brings less uncertainty.

  10. Fundamentals of functional analysis

    CERN Document Server

    Farenick, Douglas

    2016-01-01

    This book provides a unique path for graduate or advanced undergraduate students to begin studying the rich subject of functional analysis with fewer prerequisites than is normally required. The text begins with a self-contained and highly efficient introduction to topology and measure theory, which focuses on the essential notions required for the study of functional analysis, and which are often buried within full-length overviews of the subjects. This is particularly useful for those in applied mathematics, engineering, or physics who need to have a firm grasp of functional analysis, but not necessarily some of the more abstruse aspects of topology and measure theory normally encountered. The reader is assumed to only have knowledge of basic real analysis, complex analysis, and algebra. The latter part of the text provides an outstanding treatment of Banach space theory and operator theory, covering topics not usually found together in other books on functional analysis. Written in a clear, concise manner,...

  11. From analysis to surface

    DEFF Research Database (Denmark)

    Bemman, Brian; Meredith, David

    it with a “ground truth” analysis of the same music pro- duced by a human expert (see, in particular, [5]). In this paper, we explore the problem of generating an encoding of the musical surface of a work automatically from a systematic encoding of an analysis. The ability to do this depends on one having...... an effective (i.e., comput- able), correct and complete description of some aspect of the structure of the music. Generating the surface struc- ture of a piece from an analysis in this manner serves as a proof of the analysis' correctness, effectiveness and com- pleteness. We present a reductive analysis......In recent years, a significant body of research has focused on developing algorithms for computing analyses of mu- sical works automatically from encodings of these works' surfaces [3,4,7,10,11]. The quality of the output of such analysis algorithms is typically evaluated by comparing...

  12. Functional Object Analysis

    DEFF Research Database (Denmark)

    Raket, Lars Lau

    We propose a direction it the field of statistics which we will call functional object analysis. This subfields considers the analysis of functional objects defined on continuous domains. In this setting we will focus on model-based statistics, with a particularly emphasis on mixed......-effect formulations, where the observed functional signal is assumed to consist of both fixed and random functional effects. This thesis takes the initial steps toward the development of likelihood-based methodology for functional objects. We first consider analysis of functional data defined on high...

  13. Basic stress analysis

    CERN Document Server

    Iremonger, M J

    1982-01-01

    BASIC Stress Analysis aims to help students to become proficient at BASIC programming by actually using it in an important engineering subject. It also enables the student to use computing as a means of learning stress analysis because writing a program is analogous to teaching-it is necessary to understand the subject matter. The book begins by introducing the BASIC approach and the concept of stress analysis at first- and second-year undergraduate level. Subsequent chapters contain a summary of relevant theory, worked examples containing computer programs, and a set of problems. Topics c

  14. Biological sequence analysis

    DEFF Research Database (Denmark)

    Durbin, Richard; Eddy, Sean; Krogh, Anders Stærmose

    This book provides an up-to-date and tutorial-level overview of sequence analysis methods, with particular emphasis on probabilistic modelling. Discussed methods include pairwise alignment, hidden Markov models, multiple alignment, profile searches, RNA secondary structure analysis, and phylogene...

  15. Confirmatory Composite Analysis

    NARCIS (Netherlands)

    Schuberth, Florian; Henseler, Jörg; Dijkstra, Theo K.

    2018-01-01

    We introduce confirmatory composite analysis (CCA) as a structural equation modeling technique that aims at testing composite models. CCA entails the same steps as confirmatory factor analysis: model specification, model identification, model estimation, and model testing. Composite models are

  16. Evaluation of pavement life cycle cost analysis: Review and analysis

    Directory of Open Access Journals (Sweden)

    Peyman Babashamsi

    2016-07-01

    Full Text Available The cost of road construction consists of design expenses, material extraction, construction equipment, maintenance and rehabilitation strategies, and operations over the entire service life. An economic analysis process known as Life-Cycle Cost Analysis (LCCA is used to evaluate the cost-efficiency of alternatives based on the Net Present Value (NPV concept. It is essential to evaluate the above-mentioned cost aspects in order to obtain optimum pavement life-cycle costs. However, pavement managers are often unable to consider each important element that may be required for performing future maintenance tasks. Over the last few decades, several approaches have been developed by agencies and institutions for pavement Life-Cycle Cost Analysis (LCCA. While the transportation community has increasingly been utilising LCCA as an essential practice, several organisations have even designed computer programs for their LCCA approaches in order to assist with the analysis. Current LCCA methods are analysed and LCCA software is introduced in this article. Subsequently, a list of economic indicators is provided along with their substantial components. Collecting previous literature will help highlight and study the weakest aspects so as to mitigate the shortcomings of existing LCCA methods and processes. LCCA research will become more robust if improvements are made, facilitating private industries and government agencies to accomplish their economic aims. Keywords: Life-Cycle Cost Analysis (LCCA, Pavement management, LCCA software, Net Present Value (NPV

  17. Real time analysis under EDS

    International Nuclear Information System (INIS)

    Schneberk, D.

    1985-07-01

    This paper describes the analysis component of the Enrichment Diagnostic System (EDS) developed for the Atomic Vapor Laser Isotope Separation Program (AVLIS) at Lawrence Livermore National Laboratory (LLNL). Four different types of analysis are performed on data acquired through EDS: (1) absorption spectroscopy on laser-generated spectral lines, (2) mass spectrometer analysis, (3) general purpose waveform analysis, and (4) separation performance calculations. The information produced from this data includes: measures of particle density and velocity, partial pressures of residual gases, and overall measures of isotope enrichment. The analysis component supports a variety of real-time modeling tasks, a means for broadcasting data to other nodes, and a great degree of flexibility for tailoring computations to the exact needs of the process. A particular data base structure and program flow is common to all types of analysis. Key elements of the analysis component are: (1) a fast access data base which can configure all types of analysis, (2) a selected set of analysis routines, (3) a general purpose data manipulation and graphics package for the results of real time analysis. Each of these components are described with an emphasis upon how each contributes to overall system capability. 3 figs

  18. Trend Analysis Using Microcomputers.

    Science.gov (United States)

    Berger, Carl F.

    A trend analysis statistical package and additional programs for the Apple microcomputer are presented. They illustrate strategies of data analysis suitable to the graphics and processing capabilities of the microcomputer. The programs analyze data sets using examples of: (1) analysis of variance with multiple linear regression; (2) exponential…

  19. Life-Cycle Cost-Benefit Analysis

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    2010-01-01

    The future use of Life-Cycle Cost-Benefit (LCCB) analysis is discussed in this paper. A more complete analysis including not only the traditional factors and user costs, but also factors which are difficult to include in the analysis is needed in the future.......The future use of Life-Cycle Cost-Benefit (LCCB) analysis is discussed in this paper. A more complete analysis including not only the traditional factors and user costs, but also factors which are difficult to include in the analysis is needed in the future....

  20. Evaluating Style Analysis

    NARCIS (Netherlands)

    F.A. de Roon (Frans); T.E. Nijman (Theo); B.J.M. Werker

    2000-01-01

    textabstractIn this paper we evaluate applications of (return based) style analysis. The portfolio and positivity constraints imposed by style analysis are useful in constructing mimicking portfolios without short positions. Such mimicking portfolios can be used e.g. to construct efficient

  1. Strictness Analysis for Attribute Grammars

    DEFF Research Database (Denmark)

    Rosendahl, Mads

    1992-01-01

    interpretation of attribute grammars. The framework is used to construct a strictness analysis for attribute grammars. Results of the analysis enable us to transform an attribute grammar such that attributes are evaluated during parsing, if possible. The analysis is proved correct by relating it to a fixpoint...... semantics for attribute grammars. An implementation of the analysis is discussed and some extensions to the analysis are mentioned....

  2. Earth analysis methods, subsurface feature detection methods, earth analysis devices, and articles of manufacture

    Science.gov (United States)

    West, Phillip B [Idaho Falls, ID; Novascone, Stephen R [Idaho Falls, ID; Wright, Jerry P [Idaho Falls, ID

    2011-09-27

    Earth analysis methods, subsurface feature detection methods, earth analysis devices, and articles of manufacture are described. According to one embodiment, an earth analysis method includes engaging a device with the earth, analyzing the earth in a single substantially lineal direction using the device during the engaging, and providing information regarding a subsurface feature of the earth using the analysis.

  3. Rescaled Range Analysis and Detrended Fluctuation Analysis: Finite Sample Properties and Confidence Intervals

    Czech Academy of Sciences Publication Activity Database

    Krištoufek, Ladislav

    4/2010, č. 3 (2010), s. 236-250 ISSN 1802-4696 R&D Projects: GA ČR GD402/09/H045; GA ČR GA402/09/0965 Grant - others:GA UK(CZ) 118310 Institutional research plan: CEZ:AV0Z10750506 Keywords : rescaled range analysis * detrended fluctuation analysis * Hurst exponent * long-range dependence Subject RIV: AH - Economics http://library.utia.cas.cz/separaty/2010/E/kristoufek-rescaled range analysis and detrended fluctuation analysis finite sample properties and confidence intervals.pdf

  4. SMART performance analysis methodology

    International Nuclear Information System (INIS)

    Lim, H. S.; Kim, H. C.; Lee, D. J.

    2001-04-01

    To ensure the required and desired operation over the plant lifetime, the performance analysis for the SMART NSSS design is done by means of the specified analysis methodologies for the performance related design basis events(PRDBE). The PRDBE is an occurrence(event) that shall be accommodated in the design of the plant and whose consequence would be no more severe than normal service effects of the plant equipment. The performance analysis methodology which systematizes the methods and procedures to analyze the PRDBEs is as follows. Based on the operation mode suitable to the characteristics of the SMART NSSS, the corresponding PRDBEs and allowable range of process parameters for these events are deduced. With the developed control logic for each operation mode, the system thermalhydraulics are analyzed for the chosen PRDBEs using the system analysis code. Particularly, because of different system characteristics of SMART from the existing commercial nuclear power plants, the operation mode, PRDBEs, control logic, and analysis code should be consistent with the SMART design. This report presents the categories of the PRDBEs chosen based on each operation mode and the transition among these and the acceptance criteria for each PRDBE. It also includes the analysis methods and procedures for each PRDBE and the concept of the control logic for each operation mode. Therefore this report in which the overall details for SMART performance analysis are specified based on the current SMART design, would be utilized as a guide for the detailed performance analysis

  5. Isogeometric failure analysis

    NARCIS (Netherlands)

    Verhoosel, C.V.; Scott, M.A.; Borden, M.J.; Borst, de R.; Hughes, T.J.R.; Mueller-Hoeppe, D.; Loehnert, S.; Reese, S.

    2011-01-01

    Isogeometric analysis is a versatile tool for failure analysis. On the one hand, the excellent control over the inter-element continuity conditions enables a natural incorporation of continuum constitutive relations that incorporate higher-order strain gradients, as in gradient plasticity or damage.

  6. Cognitive task analysis

    NARCIS (Netherlands)

    Schraagen, J.M.C.

    2000-01-01

    Cognitive task analysis is defined as the extension of traditional task analysis techniques to yield information about the knowledge, thought processes and goal structures that underlie observable task performance. Cognitive task analyses are conducted for a wide variety of purposes, including the

  7. Evaluating Style Analysis

    NARCIS (Netherlands)

    de Roon, F.A.; Nijman, T.E.; Ter Horst, J.R.

    2000-01-01

    In this paper we evaluate applications of (return based) style analysis.The portfolio and positivity constraints imposed by style analysis are useful in constructing mimicking portfolios without short positions.Such mimicking portfolios can be used, e.g., to construct efficient portfolios of mutual

  8. Circuit analysis with Multisim

    CERN Document Server

    Baez-Lopez, David

    2011-01-01

    This book is concerned with circuit simulation using National Instruments Multisim. It focuses on the use and comprehension of the working techniques for electrical and electronic circuit simulation. The first chapters are devoted to basic circuit analysis.It starts by describing in detail how to perform a DC analysis using only resistors and independent and controlled sources. Then, it introduces capacitors and inductors to make a transient analysis. In the case of transient analysis, it is possible to have an initial condition either in the capacitor voltage or in the inductor current, or bo

  9. Extending and automating a Systems-Theoretic hazard analysis for requirements generation and analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, John (Massachusetts Institute of Technology)

    2012-05-01

    Systems Theoretic Process Analysis (STPA) is a powerful new hazard analysis method designed to go beyond traditional safety techniques - such as Fault Tree Analysis (FTA) - that overlook important causes of accidents like flawed requirements, dysfunctional component interactions, and software errors. While proving to be very effective on real systems, no formal structure has been defined for STPA and its application has been ad-hoc with no rigorous procedures or model-based design tools. This report defines a formal mathematical structure underlying STPA and describes a procedure for systematically performing an STPA analysis based on that structure. A method for using the results of the hazard analysis to generate formal safety-critical, model-based system and software requirements is also presented. Techniques to automate both the analysis and the requirements generation are introduced, as well as a method to detect conflicts between the safety and other functional model-based requirements during early development of the system.

  10. Panel Analysis

    DEFF Research Database (Denmark)

    Brænder, Morten; Andersen, Lotte Bøgh

    2014-01-01

    Based on our 2013-article, ”Does Deployment to War Affect Soldiers' Public Service Motivation – A Panel Study of Soldiers Before and After their Service in Afghanistan”, we present Panel Analysis as a methodological discipline. Panels consist of multiple units of analysis, observed at two or more...... in research settings where it is not possible to distribute units of analysis randomly or where the independent variables cannot be manipulated. The greatest disadvantage in regard to using panel studies is that data may be difficult to obtain. This is most clearly vivid in regard to the use of panel surveys...... points in time. In comparison with traditional cross-sectional studies, the advantage of using panel studies is that the time dimension enables us to study effects. Whereas experimental designs may have a clear advantage in regard to causal inference, the strength of panel studies is difficult to match...

  11. Real analysis

    CERN Document Server

    DiBenedetto, Emmanuele

    2016-01-01

    The second edition of this classic textbook presents a rigorous and self-contained introduction to real analysis with the goal of providing a solid foundation for future coursework and research in applied mathematics. Written in a clear and concise style, it covers all of the necessary subjects as well as those often absent from standard introductory texts. Each chapter features a “Problems and Complements” section that includes additional material that briefly expands on certain topics within the chapter and numerous exercises for practicing the key concepts. The first eight chapters explore all of the basic topics for training in real analysis, beginning with a review of countable sets before moving on to detailed discussions of measure theory, Lebesgue integration, Banach spaces, functional analysis, and weakly differentiable functions. More topical applications are discussed in the remaining chapters, such as maximal functions, functions of bounded mean oscillation, rearrangements, potential theory, a...

  12. Numerical analysis

    CERN Document Server

    Scott, L Ridgway

    2011-01-01

    Computational science is fundamentally changing how technological questions are addressed. The design of aircraft, automobiles, and even racing sailboats is now done by computational simulation. The mathematical foundation of this new approach is numerical analysis, which studies algorithms for computing expressions defined with real numbers. Emphasizing the theory behind the computation, this book provides a rigorous and self-contained introduction to numerical analysis and presents the advanced mathematics that underpin industrial software, including complete details that are missing from most textbooks. Using an inquiry-based learning approach, Numerical Analysis is written in a narrative style, provides historical background, and includes many of the proofs and technical details in exercises. Students will be able to go beyond an elementary understanding of numerical simulation and develop deep insights into the foundations of the subject. They will no longer have to accept the mathematical gaps that ex...

  13. Modern real analysis

    CERN Document Server

    Ziemer, William P

    2017-01-01

    This first year graduate text is a comprehensive resource in real analysis based on a modern treatment of measure and integration. Presented in a definitive and self-contained manner, it features a natural progression of concepts from simple to difficult. Several innovative topics are featured, including differentiation of measures, elements of Functional Analysis, the Riesz Representation Theorem, Schwartz distributions, the area formula, Sobolev functions and applications to harmonic functions. Together, the selection of topics forms a sound foundation in real analysis that is particularly suited to students going on to further study in partial differential equations. This second edition of Modern Real Analysis contains many substantial improvements, including the addition of problems for practicing techniques, and an entirely new section devoted to the relationship between Lebesgue and improper integrals. Aimed at graduate students with an understanding of advanced calculus, the text will also appeal to mo...

  14. A PROOF Analysis Framework

    International Nuclear Information System (INIS)

    González Caballero, I; Cuesta Noriega, A; Rodríguez Marrero, A; Fernández del Castillo, E

    2012-01-01

    The analysis of the complex LHC data usually follows a standard path that aims at minimizing not only the amount of data but also the number of observables used. After a number of steps of slimming and skimming the data, the remaining few terabytes of ROOT files hold a selection of the events and a flat structure for the variables needed that can be more easily inspected and traversed in the final stages of the analysis. PROOF arises at this point as an efficient mechanism to distribute the analysis load by taking advantage of all the cores in modern CPUs through PROOF Lite, or by using PROOF Cluster or PROOF on Demand tools to build dynamic PROOF cluster on computing facilities with spare CPUs. However using PROOF at the level required for a serious analysis introduces some difficulties that may scare new adopters. We have developed the PROOF Analysis Framework (PAF) to facilitate the development of new analysis by uniformly exposing the PROOF related configurations across technologies and by taking care of the routine tasks as much as possible. We describe the details of the PAF implementation as well as how we succeeded in engaging a group of CMS physicists to use PAF as their daily analysis framework.

  15. Marketing Mix Formulation for Higher Education: An Integrated Analysis Employing Analytic Hierarchy Process, Cluster Analysis and Correspondence Analysis

    Science.gov (United States)

    Ho, Hsuan-Fu; Hung, Chia-Chi

    2008-01-01

    Purpose: The purpose of this paper is to examine how a graduate institute at National Chiayi University (NCYU), by using a model that integrates analytic hierarchy process, cluster analysis and correspondence analysis, can develop effective marketing strategies. Design/methodology/approach: This is primarily a quantitative study aimed at…

  16. Manual versus Automated Narrative Analysis of Agrammatic Production Patterns: The Northwestern Narrative Language Analysis and Computerized Language Analysis

    Science.gov (United States)

    Hsu, Chien-Ju; Thompson, Cynthia K.

    2018-01-01

    Purpose: The purpose of this study is to compare the outcomes of the manually coded Northwestern Narrative Language Analysis (NNLA) system, which was developed for characterizing agrammatic production patterns, and the automated Computerized Language Analysis (CLAN) system, which has recently been adopted to analyze speech samples of individuals…

  17. Cost analysis guidelines

    International Nuclear Information System (INIS)

    Strait, R.S.

    1996-01-01

    The first phase of the Depleted Uranium Hexafluoride Management Program (Program)--management strategy selection--consists of several program elements: Technology Assessment, Engineering Analysis, Cost Analysis, and preparation of an Environmental Impact Statement (EIS). Cost Analysis will estimate the life-cycle costs associated with each of the long-term management strategy alternatives for depleted uranium hexafluoride (UF6). The scope of Cost Analysis will include all major expenditures, from the planning and design stages through decontamination and decommissioning. The costs will be estimated at a scoping or preconceptual design level and are intended to assist decision makers in comparing alternatives for further consideration. They will not be absolute costs or bid-document costs. The purpose of the Cost Analysis Guidelines is to establish a consistent approach to analyzing of cost alternatives for managing Department of Energy's (DOE's) stocks of depleted uranium hexafluoride (DUF6). The component modules that make up the DUF6 management program differ substantially in operational maintenance, process-options, requirements for R and D, equipment, facilities, regulatory compliance, (O and M), and operations risk. To facilitate a consistent and equitable comparison of costs, the guidelines offer common definitions, assumptions or basis, and limitations integrated with a standard approach to the analysis. Further, the goal is to evaluate total net life-cycle costs and display them in a way that gives DOE the capability to evaluate a variety of overall DUF6 management strategies, including commercial potential. The cost estimates reflect the preconceptual level of the designs. They will be appropriate for distinguishing among management strategies

  18. Radiation and environmental data analysis computer (REDAC) hardware, software band analysis procedures

    International Nuclear Information System (INIS)

    Hendricks, T.J.

    1985-01-01

    The REDAC was conceived originally as a tape verifier for the Radiation and Environmental Data Acquisition Recorder (REDAR). From that simple beginning in 1971, the REDAC has evolved into a family of systems used for complete analysis of data obtained by the REDAR and other acquisition systems. Portable or mobile REDACs are deployed to support checkout and analysis tasks in the field. Laboratory systems are additionally used for software development, physics investigations, data base management and graphics. System configurations range from man-portable systems to a large laboratory-based system which supports time-shared analysis and development tasks. Custom operating software allows the analyst to process data either interactively or by batch procedures. Analysis packages are provided for numerous necessary functions. All these analysis procedures can be performed even on the smallest man-portable REDAC. Examples of the multi-isotope stripping and radiation isopleth mapping are presented. Techniques utilized for these operations are also presented

  19. Systems engineering and analysis

    CERN Document Server

    Blanchard, Benjamin S

    2010-01-01

    For senior-level undergraduate and first and second year graduate systems engineering and related courses. A total life-cycle approach to systems and their analysis. This practical introduction to systems engineering and analysis provides the concepts, methodologies, models, and tools needed to understand and implement a total life-cycle approach to systems and their analysis. The authors focus first on the process of bringing systems into being--beginning with the identification of a need and extending that need through requirements determination, functional analysis and allocation, design synthesis, evaluation, and validation, operation and support, phase-out, and disposal. Next, the authors discuss the improvement of systems currently in being, showing that by employing the iterative process of analysis, evaluation, feedback, and modification, most systems in existence can be improved in their affordability, effectiveness, and stakeholder satisfaction.

  20. Numerical analysis

    CERN Document Server

    Brezinski, C

    2012-01-01

    Numerical analysis has witnessed many significant developments in the 20th century. This book brings together 16 papers dealing with historical developments, survey papers and papers on recent trends in selected areas of numerical analysis, such as: approximation and interpolation, solution of linear systems and eigenvalue problems, iterative methods, quadrature rules, solution of ordinary-, partial- and integral equations. The papers are reprinted from the 7-volume project of the Journal of Computational and Applied Mathematics on '/homepage/sac/cam/na2000/index.html<

  1. Automation of activation analysis

    International Nuclear Information System (INIS)

    Ivanov, I.N.; Ivanets, V.N.; Filippov, V.V.

    1985-01-01

    The basic data on the methods and equipment of activation analysis are presented. Recommendations on the selection of activation analysis techniques, and especially the technique envisaging the use of short-lived isotopes, are given. The equipment possibilities to increase dataway carrying capacity, using modern computers for the automation of the analysis and data processing procedure, are shown

  2. Intelligent audio analysis

    CERN Document Server

    Schuller, Björn W

    2013-01-01

    This book provides the reader with the knowledge necessary for comprehension of the field of Intelligent Audio Analysis. It firstly introduces standard methods and discusses the typical Intelligent Audio Analysis chain going from audio data to audio features to audio recognition.  Further, an introduction to audio source separation, and enhancement and robustness are given. After the introductory parts, the book shows several applications for the three types of audio: speech, music, and general sound. Each task is shortly introduced, followed by a description of the specific data and methods applied, experiments and results, and a conclusion for this specific task. The books provides benchmark results and standardized test-beds for a broader range of audio analysis tasks. The main focus thereby lies on the parallel advancement of realism in audio analysis, as too often today’s results are overly optimistic owing to idealized testing conditions, and it serves to stimulate synergies arising from transfer of ...

  3. Advantages of Wavelet analysis compared to Fourier analysis for the interpretation of electrochemical noise

    International Nuclear Information System (INIS)

    Espada, L.; Sanjurjo, M.; Urrejola, S.; Bouzada, F.; Rey, G.; Sanchez, A.

    2003-01-01

    Given its simplicity and low cost compared to other types of methodologies, the measurement and interpretation of Electrochemical Noise, is consolidating itself as one of the analysis methods most frequently used for the interpretation of corrosion. As the technique is still evolving, standard treatment methodologies for data retrieved in experiments do not exist yet. To date, statistical analysis and the Fourier analysis are commonly used in order to establish the parameters that may characterize the recording of potential and current electrochemical noise. This study introduces a new methodology based on wavelet analysis and presents its advantages with regards to the Fourier analysis in distinguishes periodical and non-periodical variations in the signal power in time and frequency, as opposed to the Fourier analysis that only considers the frequency. (Author) 15 refs

  4. 21 CFR 1230.34 - Analysis.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Analysis. 1230.34 Section 1230.34 Food and Drugs... POISON ACT Administrative Procedures § 1230.34 Analysis. (a) The methods of examination or analysis..., provided, however, that any method of analysis or examination satisfactory to the Food and Drug...

  5. Real analysis

    CERN Document Server

    Loeb, Peter A

    2016-01-01

    This textbook is designed for a year-long course in real analysis taken by beginning graduate and advanced undergraduate students in mathematics and other areas such as statistics, engineering, and economics. Written by one of the leading scholars in the field, it elegantly explores the core concepts in real analysis and introduces new, accessible methods for both students and instructors. The first half of the book develops both Lebesgue measure and, with essentially no additional work for the student, general Borel measures for the real line. Notation indicates when a result holds only for Lebesgue measure. Differentiation and absolute continuity are presented using a local maximal function, resulting in an exposition that is both simpler and more general than the traditional approach. The second half deals with general measures and functional analysis, including Hilbert spaces, Fourier series, and the Riesz representation theorem for positive linear functionals on continuous functions with compact support....

  6. Numerical analysis

    CERN Document Server

    Jacques, Ian

    1987-01-01

    This book is primarily intended for undergraduates in mathematics, the physical sciences and engineering. It introduces students to most of the techniques forming the core component of courses in numerical analysis. The text is divided into eight chapters which are largely self-contained. However, with a subject as intricately woven as mathematics, there is inevitably some interdependence between them. The level of difficulty varies and, although emphasis is firmly placed on the methods themselves rather than their analysis, we have not hesitated to include theoretical material when we consider it to be sufficiently interesting. However, it should be possible to omit those parts that do seem daunting while still being able to follow the worked examples and to tackle the exercises accompanying each section. Familiarity with the basic results of analysis and linear algebra is assumed since these are normally taught in first courses on mathematical methods. For reference purposes a list of theorems used in the t...

  7. Physics and Video Analysis

    Science.gov (United States)

    Allain, Rhett

    2016-05-01

    We currently live in a world filled with videos. There are videos on YouTube, feature movies and even videos recorded with our own cameras and smartphones. These videos present an excellent opportunity to not only explore physical concepts, but also inspire others to investigate physics ideas. With video analysis, we can explore the fantasy world in science-fiction films. We can also look at online videos to determine if they are genuine or fake. Video analysis can be used in the introductory physics lab and it can even be used to explore the make-believe physics embedded in video games. This book covers the basic ideas behind video analysis along with the fundamental physics principles used in video analysis. The book also includes several examples of the unique situations in which video analysis can be used.

  8. Real analysis and applications

    CERN Document Server

    Botelho, Fabio Silva

    2018-01-01

    This textbook introduces readers to real analysis in one and n dimensions. It is divided into two parts: Part I explores real analysis in one variable, starting with key concepts such as the construction of the real number system, metric spaces, and real sequences and series. In turn, Part II addresses the multi-variable aspects of real analysis. Further, the book presents detailed, rigorous proofs of the implicit theorem for the vectorial case by applying the Banach fixed-point theorem and the differential forms concept to surfaces in Rn. It also provides a brief introduction to Riemannian geometry. With its rigorous, elegant proofs, this self-contained work is easy to read, making it suitable for undergraduate and beginning graduate students seeking a deeper understanding of real analysis and applications, and for all those looking for a well-founded, detailed approach to real analysis.

  9. Comparison of descriptive sensory analysis and chemical analysis for oxidative changes in milk

    DEFF Research Database (Denmark)

    Hedegaard, R V; Kristensen, D; Nielsen, Jacob Holm

    2006-01-01

    and lipolytic changes occurring in the milk during chill storage for 4 d. Sensory analysis and chemical analysis showed high correlation between the typical descriptors for oxidation such as cardboard, metallic taste, and boiled milk and specific chemical markers for oxidation such as hexanal. Notably, primary......Oxidation in 3 types of bovine milk with different fatty acid profiles obtained through manipulation of feed was evaluated by analytical methods quantifying the content of potential antioxidants, the tendency of formation of free radicals, and the accumulation of primary and secondary oxidation...... products. The milk samples were evaluated in parallel by descriptive sensory analysis by a trained panel, and the correlation between the chemical analysis and the descriptive sensory analysis was evaluated. The fatty acid composition of the 3 types of milk was found to influence the oxidative...

  10. Comparison of descriptive sensory analysis and chemical analysis for oxidative changes in milk

    DEFF Research Database (Denmark)

    Hedegaard, Rikke Susanne Vingborg; Kristensen, D.; Nielsen, J. H.

    2006-01-01

    products. The milk samples were evaluated in parallel by descriptive sensory analysis by a trained panel, and the correlation between the chemical analysis and the descriptive sensory analysis was evaluated. The fatty acid composition of the 3 types of milk was found to influence the oxidative...... and lipolytic changes occurring in the milk during chill storage for 4 d. Sensory analysis and chemical analysis showed high correlation between the typical descriptors for oxidation such as cardboard, metallic taste, and boiled milk and specific chemical markers for oxidation such as hexanal. Notably, primary...... oxidation products (i.e., lipid hydroperoxides) and even the tendency of formation of radicals as measured by electron spin resonance spectroscopy were also highly correlated to the sensory descriptors for oxidation. Electron spin resonance spectroscopy should accordingly be further explored as a routine...

  11. Containment vessel stability analysis

    International Nuclear Information System (INIS)

    Harstead, G.A.; Morris, N.F.; Unsal, A.I.

    1983-01-01

    The stability analysis for a steel containment shell is presented herein. The containment is a freestanding shell consisting of a vertical cylinder with a hemispherical dome. It is stiffened by large ring stiffeners and relatively small longitudinal stiffeners. The containment vessel is subjected to both static and dynamic loads which can cause buckling. These loads must be combined prior to their use in a stability analysis. The buckling loads were computed with the aid of the ASME Code case N-284 used in conjunction with general purpose computer codes and in-house programs. The equations contained in the Code case were used to compute the knockdown factors due to shell imperfections. After these knockdown factors were applied to the critical stress states determined by freezing the maximum dynamic stresses and combining them with other static stresses, a linear bifurcation analysis was carried out with the aid of the BOSOR4 program. Since the containment shell contained large penetrations, the Code case had to be supplemented by a local buckling analysis of the shell area surrounding the largest penetration. This analysis was carried out with the aid of the NASTRAN program. Although the factor of safety against buckling obtained in this analysis was satisfactory, it is claimed that the use of the Code case knockdown factors are unduly conservative when applied to the analysis of buckling around penetrations. (orig.)

  12. Statistical data analysis

    International Nuclear Information System (INIS)

    Hahn, A.A.

    1994-11-01

    The complexity of instrumentation sometimes requires data analysis to be done before the result is presented to the control room. This tutorial reviews some of the theoretical assumptions underlying the more popular forms of data analysis and presents simple examples to illuminate the advantages and hazards of different techniques

  13. Elemental analysis of granite by instrumental neutron activation analysis (INAA) and X-ray fluorescence analysis (XRF)

    International Nuclear Information System (INIS)

    El-Taher, A.

    2012-01-01

    The instrumental neutron activation analysis technique (INAA) was used for qualitative and quantitative analysis of granite samples collected from four locations in the Aswan area in South Egypt. The samples were prepared together with their standards and simultaneously irradiated in a neutron flux of 7×10 11 n/cm 2 s in the TRIGA Mainz research reactor. Gamma-ray spectra from an hyper-pure germanium detector were analyzed. The present study provides the basic data of elemental concentrations of granite rocks. The following elements have been determined Na, Mg, K, Fe, Mn, Sc, Cr, Ti, Co, Zn, Ga, Rb, Zr, Nb, Sn, Ba, Cs, La, Ce, Nd, Sm, Eu, Yb, Lu, Hf, Ta, Th and U. The X-ray fluorescence (XRF) was used for comparison and to detect elements, which can be detected only by XRF such as F, S, Cl, Co, Cu, Mo, Ni, Pb, Se and V. The data presented here are our contribution to understanding the elemental composition of the granite rocks. Because there are no existing databases for the elemental analysis of granite, our results are a start to establishing a database for the Egyptian granite. It is hoped that the data presented here will be useful to those dealing with geochemistry, granite chemistry and related fields. - Highlights: ► Instrumental neutron activation analysis technique (INAA) was used for qualitative and quantitative analysis of granite. ► The samples were prepared together with their standards and simultaneously irradiated in a neutron flux of 7×10 11 n/cm 2 s in the TRIGA Mainz research reactor. ► Following elements have been determined Na, Mg, K, Fe, Mn, Sc, Cr, Ti, Co, Zn, Ga, Rb, Zr, Nb, Sn, Ba, Cs, La, Ce, Nd, Sm, Eu, Yb, Lu, Hf, Ta, Th and U.

  14. Regional energy facility siting analysis

    International Nuclear Information System (INIS)

    Eberhart, R.C.; Eagles, T.W.

    1976-01-01

    Results of the energy facility siting analysis portion of a regional pilot study performed for the anticipated National Energy Siting and Facility Report are presented. The question of cell analysis versus site-specific analysis is explored, including an evaluation of the difference in depth between the two approaches. A discussion of the possible accomplishments of regional analysis is presented. It is concluded that regional sitting analysis could be of use in a national siting study, if its inherent limits are recognized

  15. Analysis of Lead and Zinc by Mercury-Free Potentiometric Stripping Analysis

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov

    1997-01-01

    A method is presented for trace-element analysis of lead and zinc by potentiometric stripping analysis (PSA) where both the glassy-carbon working electrode and the electrolyte are free of mercury. Analysis of zinc requires an activation procedure of the glassy-carbon electrode. The activation...... is performed by pre-concentrating zinc on glassy carbon at -1400 mV(SCE) in a mercury-free electrolyte containing 0.1 M HCl and 2 ppm Zn2+, followed by stripping at approx. -1050 mV. A linear relationship between stripping peak areas, recorded in the derivative mode, and concentration was found...

  16. Evaluation and presentation of analysis methods for reception analysis in reprocessing

    International Nuclear Information System (INIS)

    Mainka, E.

    1985-01-01

    The fissile material content in the dissolving or balancing tank of a reprocessing plant has special significance in nuclear fuel balancing. This is the first opportunity for destructive analysis of the fuel content of the material after burn-up of fuel elements in the reactor. In the current state-of-the-art, all balancing methods are based directly or indirectly on data obtained by chemical analysis. The following methods are evaluated: Mass-spectroscopic isotope dilution analysis, X-ray fluorescence spectroscopy, Isotopic correlation, Gamma absorptiometry, Redox titration, Emission spectroscopy after plasma excitation, Alpha spectroscopy, and Laser Raman spectroscopy

  17. Analysis apparatus and method of analysis

    International Nuclear Information System (INIS)

    1976-01-01

    A continuous streaming method developed for the excution of immunoassays is described in this patent. In addition, a suitable apparatus for the method was developed whereby magnetic particles are automatically employed for the consecutive analysis of a series of liquid samples via the RIA technique

  18. Defining disease beyond conceptual analysis: an analysis of conceptual analysis in philosophy of medicine.

    Science.gov (United States)

    Lemoine, Maël

    2013-08-01

    Conceptual analysis of health and disease is portrayed as consisting in the confrontation of a set of criteria--a "definition"--with a set of cases, called instances of either "health" or "disease." Apart from logical counter-arguments, there is no other way to refute an opponent's definition than by providing counter-cases. As resorting to intensional stipulation (stipulation of meaning) is not forbidden, several contenders can therefore be deemed to have succeeded. This implies that conceptual analysis alone is not likely to decide between naturalism and normativism. An alternative to this approach would be to examine whether the concept of disease can be naturalized.

  19. Mastering Clojure data analysis

    CERN Document Server

    Rochester, Eric

    2014-01-01

    This book consists of a practical, example-oriented approach that aims to help you learn how to use Clojure for data analysis quickly and efficiently.This book is great for those who have experience with Clojure and who need to use it to perform data analysis. This book will also be hugely beneficial for readers with basic experience in data analysis and statistics.

  20. Evaluation of Analysis by Cross-Validation, Part II: Diagnostic and Optimization of Analysis Error Covariance

    Directory of Open Access Journals (Sweden)

    Richard Ménard

    2018-02-01

    Full Text Available We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular, we use the variance of passive observation-minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

  1. Convex analysis

    CERN Document Server

    Rockafellar, Ralph Tyrell

    2015-01-01

    Available for the first time in paperback, R. Tyrrell Rockafellar's classic study presents readers with a coherent branch of nonlinear mathematical analysis that is especially suited to the study of optimization problems. Rockafellar's theory differs from classical analysis in that differentiability assumptions are replaced by convexity assumptions. The topics treated in this volume include: systems of inequalities, the minimum or maximum of a convex function over a convex set, Lagrange multipliers, minimax theorems and duality, as well as basic results about the structure of convex sets and

  2. Outlier analysis

    CERN Document Server

    Aggarwal, Charu C

    2013-01-01

    With the increasing advances in hardware technology for data collection, and advances in software technology (databases) for data organization, computer scientists have increasingly participated in the latest advancements of the outlier analysis field. Computer scientists, specifically, approach this field based on their practical experiences in managing large amounts of data, and with far fewer assumptions- the data can be of any type, structured or unstructured, and may be extremely large.Outlier Analysis is a comprehensive exposition, as understood by data mining experts, statisticians and

  3. Elementary analysis

    CERN Document Server

    Snell, K S; Langford, W J; Maxwell, E A

    1966-01-01

    Elementary Analysis, Volume 2 introduces several of the ideas of modern mathematics in a casual manner and provides the practical experience in algebraic and analytic operations that lays a sound foundation of basic skills. This book focuses on the nature of number, algebraic and logical structure, groups, rings, fields, vector spaces, matrices, sequences, limits, functions and inverse functions, complex numbers, and probability. The logical structure of analysis given through the treatment of differentiation and integration, with applications to the trigonometric and logarithmic functions, is

  4. Task analysis and computer aid development for human reliability analysis in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, W. C.; Kim, H.; Park, H. S.; Choi, H. H.; Moon, J. M.; Heo, J. Y.; Ham, D. H.; Lee, K. K.; Han, B. T. [Korea Advanced Institute of Science and Technology, Taejeon (Korea)

    2001-04-01

    Importance of human reliability analysis (HRA) that predicts the error's occurrence possibility in a quantitative and qualitative manners is gradually increased by human errors' effects on the system's safety. HRA needs a task analysis as a virtue step, but extant task analysis techniques have the problem that a collection of information about the situation, which the human error occurs, depends entirely on HRA analyzers. The problem makes results of the task analysis inconsistent and unreliable. To complement such problem, KAERI developed the structural information analysis (SIA) that helps to analyze task's structure and situations systematically. In this study, the SIA method was evaluated by HRA experts, and a prototype computerized supporting system named CASIA (Computer Aid for SIA) was developed for the purpose of supporting to perform HRA using the SIA method. Additionally, through applying the SIA method to emergency operating procedures, we derived generic task types used in emergency and accumulated the analysis results in the database of the CASIA. The CASIA is expected to help HRA analyzers perform the analysis more easily and consistently. If more analyses will be performed and more data will be accumulated to the CASIA's database, HRA analyzers can share freely and spread smoothly his or her analysis experiences, and there by the quality of the HRA analysis will be improved. 35 refs., 38 figs., 25 tabs. (Author)

  5. Structured information analysis for human reliability analysis of emergency tasks in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Won Dea; Kim, Jae Whan; Park, Jin Kyun; Ha, Jae Joo [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-02-01

    More than twenty HRA (Human Reliability Analysis) methodologies have been developed and used for the safety analysis in nuclear field during the past two decades. However, no methodology appears to have universally been accepted, as various limitations have been raised for more widely used ones. One of the most important limitations of conventional HRA is insufficient analysis of the task structure and problem space. To resolve this problem, we suggest SIA (Structured Information Analysis) for HRA. The proposed SIA consists of three parts. The first part is the scenario analysis that investigates the contextual information related to the given task on the basis of selected scenarios. The second is the goals-means analysis to define the relations between the cognitive goal and task steps. The third is the cognitive function analysis module that identifies the cognitive patterns and information flows involved in the task. Through the three-part analysis, systematic investigation is made possible from the macroscopic information on the tasks to the microscopic information on the specific cognitive processes. It is expected that analysts can attain a structured set of information that helps to predict the types and possibility of human error in the given task. 48 refs., 12 figs., 11 tabs. (Author)

  6. Maritime transportation risk analysis: Review and analysis in light of some foundational issues

    International Nuclear Information System (INIS)

    Goerlandt, Floris; Montewka, Jakub

    2015-01-01

    Many methods and applications for maritime transportation risk analysis have been presented in the literature. In parallel, there is a recent focus on foundational issues in risk analysis, with calls for intensified research on fundamental concepts and principles underlying the scientific field. This paper presents a review and analysis of risk definitions, perspectives and scientific approaches to risk analysis found in the maritime transportation application area, focusing on applications addressing accidental risk of shipping in a sea area. For this purpose, a classification of risk definitions, an overview of elements in risk perspectives and a classification of approaches to risk analysis science are applied. Results reveal that in the application area, risk is strongly tied to probability, both in definitions and perspectives, while alternative views exist. A diffuse situation is also found concerning the scientific approach to risk analysis, with realist, proceduralist and constructivist foundations co-existing. Realist approaches dominate the application area. Very few applications systematically account for uncertainty, neither concerning the evidence base nor in relation to the limitations of the risk model in relation to the space of possible outcomes. Some suggestions are made to improve the current situation, aiming to strengthen the scientific basis for risk analysis. - Highlights: • Risk analyses in maritime transportation analysed in light of foundational issues. • Focus on definitions, perspectives and scientific approaches to risk analysis. • Probability-based definitions and realist approaches dominate the field. • Findings support calls for increased focus on foundational issues in risk research. • Some suggestions are made to improve the current situation

  7. Analysis of a Braking System on the Basis of Structured Analysis Methods

    OpenAIRE

    Ben Salem J.; Lakhoua M.N.; El Amraoui L.

    2016-01-01

    In this paper, we present the general context of the research in the domain of analysis and modeling of mechatronic systems. In fact, we present à bibliographic review on some works of research about the systemic analysis of mechatronic systems. To better understand its characteristics, we start with an introduction about mechatronic systems and various fields related to these systems, after we present a few analysis and design methods applied to mechatronic systems. Finally, we apply the two...

  8. Integrated piping structural analysis system

    International Nuclear Information System (INIS)

    Motoi, Toshio; Yamadera, Masao; Horino, Satoshi; Idehata, Takamasa

    1979-01-01

    Structural analysis of the piping system for nuclear power plants has become larger in scale and in quantity. In addition, higher quality analysis is regarded as of major importance nowadays from the point of view of nuclear plant safety. In order to fulfill to the above requirements, an integrated piping structural analysis system (ISAP-II) has been developed. Basic philosophy of this system is as follows: 1. To apply the date base system. All information is concentrated. 2. To minimize the manual process in analysis, evaluation and documentation. Especially to apply the graphic system as much as possible. On the basis of the above philosophy four subsystems were made. 1. Data control subsystem. 2. Analysis subsystem. 3. Plotting subsystem. 4. Report subsystem. Function of the data control subsystem is to control all information of the data base. Piping structural analysis can be performed by using the analysis subsystem. Isometric piping drawing and mode shape, etc. can be plotted by using the plotting subsystem. Total analysis report can be made without the manual process through the reporting subsystem. (author)

  9. Longitudinal Meta-analysis

    NARCIS (Netherlands)

    Hox, J.J.; Maas, C.J.M.; Lensvelt-Mulders, G.J.L.M.

    2004-01-01

    The goal of meta-analysis is to integrate the research results of a number of studies on a specific topic. Characteristic for meta-analysis is that in general only the summary statistics of the studies are used and not the original data. When the published research results to be integrated

  10. Enabling interdisciplinary analysis

    Science.gov (United States)

    L. M. Reid

    1996-01-01

    'New requirements for evaluating environmental conditions in the Pacific Northwest have led to increased demands for interdisciplinary analysis of complex environmental problems. Procedures for watershed analysis have been developed for use on public and private lands in Washington State (Washington Forest Practices Board 1993) and for federal lands in the Pacific...

  11. Incorporating technical analysis in undergraduate curricula

    Directory of Open Access Journals (Sweden)

    Michael R. Melton

    2017-11-01

    Full Text Available Purpose – The purpose of this paper is to introduce instruction of technical analysis on the undergraduate level that can coincide with traditional teachings of fundamental analysis. Design/methodology/approach – Through examples using the latest in security analysis technology, this paper illustrates the importance of technical security analysis. Findings – This research illustrates how technical analysis techniques may be used to make more significant investment decisions. Originality/value – Kirkpatrick and Dahlquist define technical analysis as a security analysis discipline for forecasting future direction of prices through the study of past market data primarily price and volume This form of analysis has stood in direct contrast to the fundamental analysis approach whereby actual facts of the company its industry and sector may be ignored. Understanding this contrast, much of academia has chosen to continue to focus its finance curricula on fundamental analysis techniques. As more universities implement trading rooms to reflect that of industry, they must recognize that any large brokerage trading group or financial institution will typically have both a technical analysis and fundamental analysis team. Thus, the need to incorporate technical analysis into undergraduate finance curricula.

  12. Survival analysis models and applications

    CERN Document Server

    Liu, Xian

    2012-01-01

    Survival analysis concerns sequential occurrences of events governed by probabilistic laws.  Recent decades have witnessed many applications of survival analysis in various disciplines. This book introduces both classic survival models and theories along with newly developed techniques. Readers will learn how to perform analysis of survival data by following numerous empirical illustrations in SAS. Survival Analysis: Models and Applications: Presents basic techniques before leading onto some of the most advanced topics in survival analysis.Assumes only a minimal knowledge of SAS whilst enablin

  13. WWW-based remote analysis framework for UniSampo and Shaman analysis software

    International Nuclear Information System (INIS)

    Aarnio, P.A.; Ala-Heikkilae, J.J.; Routti, J.T.; Nikkinen, M.T.

    2005-01-01

    UniSampo and Shaman are well-established analytical tools for gamma-ray spectrum analysis and the subsequent radionuclide identification. These tools are normally run locally on a Unix or Linux workstation in interactive mode. However, it is also possible to run them in batch/non-interactive mode by starting them with the correct parameters. This is how they are used in the standard analysis pipeline operation. This functionality also makes it possible to use them for remote operation over the network. Framework for running UniSampo and Shaman analysis using the standard WWW-protocol has been developed. A WWW-server receives requests from the client WWW-browser and runs the analysis software via a set of CGI-scripts. Authentication, input data transfer, and output and display of the final analysis results is all carried out using standard WWW-mechanisms. This WWW-framework can be utilized, for example, by organizations that have radioactivity surveillance stations in a wide area. A computer with a standard internet/intranet connection suffices for on-site analyses. (author)

  14. Integrated genetic analysis microsystems

    International Nuclear Information System (INIS)

    Lagally, Eric T; Mathies, Richard A

    2004-01-01

    With the completion of the Human Genome Project and the ongoing DNA sequencing of the genomes of other animals, bacteria, plants and others, a wealth of new information about the genetic composition of organisms has become available. However, as the demand for sequence information grows, so does the workload required both to generate this sequence and to use it for targeted genetic analysis. Microfabricated genetic analysis systems are well poised to assist in the collection and use of these data through increased analysis speed, lower analysis cost and higher parallelism leading to increased assay throughput. In addition, such integrated microsystems may point the way to targeted genetic experiments on single cells and in other areas that are otherwise very difficult. Concomitant with these advantages, such systems, when fully integrated, should be capable of forming portable systems for high-speed in situ analyses, enabling a new standard in disciplines such as clinical chemistry, forensics, biowarfare detection and epidemiology. This review will discuss the various technologies available for genetic analysis on the microscale, and efforts to integrate them to form fully functional robust analysis devices. (topical review)

  15. Physics Metacognition Inventory Part II: Confirmatory factor analysis and Rasch analysis

    Science.gov (United States)

    Taasoobshirazi, Gita; Bailey, MarLynn; Farley, John

    2015-11-01

    The Physics Metacognition Inventory was developed to measure physics students' metacognition for problem solving. In one of our earlier studies, an exploratory factor analysis provided evidence of preliminary construct validity, revealing six components of students' metacognition when solving physics problems including knowledge of cognition, planning, monitoring, evaluation, debugging, and information management. The college students' scores on the inventory were found to be reliable and related to students' physics motivation and physics grade. However, the results of the exploratory factor analysis indicated that the questionnaire could be revised to improve its construct validity. The goal of this study was to revise the questionnaire and establish its construct validity through a confirmatory factor analysis. In addition, a Rasch analysis was applied to the data to better understand the psychometric properties of the inventory and to further evaluate the construct validity. Results indicated that the final, revised inventory is a valid, reliable, and efficient tool for assessing student metacognition for physics problem solving.

  16. Abstract Interfaces for Data Analysis Component Architecture for Data Analysis Tools

    CERN Document Server

    Barrand, G; Dönszelmann, M; Johnson, A; Pfeiffer, A

    2001-01-01

    The fast turnover of software technologies, in particular in the domain of interactivity (covering user interface and visualisation), makes it difficult for a small group of people to produce complete and polished software-tools before the underlying technologies make them obsolete. At the HepVis '99 workshop, a working group has been formed to improve the production of software tools for data analysis in HENP. Beside promoting a distributed development organisation, one goal of the group is to systematically design a set of abstract interfaces based on using modern OO analysis and OO design techniques. An initial domain analysis has come up with several categories (components) found in typical data analysis tools: Histograms, Ntuples, Functions, Vectors, Fitter, Plotter, Analyzer and Controller. Special emphasis was put on reducing the couplings between the categories to a minimum, thus optimising re-use and maintainability of any component individually. The interfaces have been defined in Java and C++ and i...

  17. Virtual data in CMS analysis

    International Nuclear Information System (INIS)

    Arbree, A.

    2003-01-01

    The use of virtual data for enhancing the collaboration between large groups of scientists is explored in several ways: by defining ''virtual'' parameter spaces which can be searched and shared in an organized way by a collaboration of scientists in the course of their analysis; by providing a mechanism to log the provenance of results and the ability to trace them back to the various stages in the analysis of real or simulated data; by creating ''check points'' in the course of an analysis to permit collaborators to explore their own analysis branches by refining selections, improving the signal to background ratio, varying the estimation of parameters, etc.; by facilitating the audit of an analysis and the reproduction of its results by a different group, or in a peer review context. We describe a prototype for the analysis of data from the CMS experiment based on the virtual data system Chimera and the object-oriented data analysis framework ROOT. The Chimera system is used to chain together several steps in the analysis process including the Monte Carlo generation of data, the simulation of detector response, the reconstruction of physics objects and their subsequent analysis, histogramming and visualization using the ROOT framework

  18. Contrast and Critique of Two Approaches to Discourse Analysis: Conversation Analysis and Speech Act Theory

    Directory of Open Access Journals (Sweden)

    Nguyen Van Han

    2014-08-01

    Full Text Available Discourse analysis, as Murcia and Olshtain (2000 assume, is a vast study of language in use that extends beyond sentence level, and it involves a more cognitive and social perspective on language use and communication exchanges. Holding a wide range of phenomena about language with society, culture and thought, discourse analysis contains various approaches: speech act, pragmatics, conversation analysis, variation analysis, and critical discourse analysis. Each approach works in its different domain to discourse. For one dimension, it shares the same assumptions or general problems in discourse analysis with the other approaches: for instance, the explanation on how we organize language into units beyond sentence boundaries, or how language is used to convey information about the world, ourselves and human relationships (Schiffrin 1994: viii. For other dimensions, each approach holds its distinctive characteristics contributing to the vastness of discourse analysis. This paper will mainly discuss two approaches to discourse analysis- conversation analysis and speech act theory- and will attempt to point out some similarities as well as contrasting features between the two approaches, followed by a short reflection on their strengths and weaknesses in the essence of each approach. The organizational and discourse features in the exchanges among three teachers at the College of Finance and Customs in Vietnam will be analysed in terms of conversation analysis and speech act theory.

  19. ADAGE signature analysis: differential expression analysis with data-defined gene sets.

    Science.gov (United States)

    Tan, Jie; Huyck, Matthew; Hu, Dongbo; Zelaya, René A; Hogan, Deborah A; Greene, Casey S

    2017-11-22

    Gene set enrichment analysis and overrepresentation analyses are commonly used methods to determine the biological processes affected by a differential expression experiment. This approach requires biologically relevant gene sets, which are currently curated manually, limiting their availability and accuracy in many organisms without extensively curated resources. New feature learning approaches can now be paired with existing data collections to directly extract functional gene sets from big data. Here we introduce a method to identify perturbed processes. In contrast with methods that use curated gene sets, this approach uses signatures extracted from public expression data. We first extract expression signatures from public data using ADAGE, a neural network-based feature extraction approach. We next identify signatures that are differentially active under a given treatment. Our results demonstrate that these signatures represent biological processes that are perturbed by the experiment. Because these signatures are directly learned from data without supervision, they can identify uncurated or novel biological processes. We implemented ADAGE signature analysis for the bacterial pathogen Pseudomonas aeruginosa. For the convenience of different user groups, we implemented both an R package (ADAGEpath) and a web server ( http://adage.greenelab.com ) to run these analyses. Both are open-source to allow easy expansion to other organisms or signature generation methods. We applied ADAGE signature analysis to an example dataset in which wild-type and ∆anr mutant cells were grown as biofilms on the Cystic Fibrosis genotype bronchial epithelial cells. We mapped active signatures in the dataset to KEGG pathways and compared with pathways identified using GSEA. The two approaches generally return consistent results; however, ADAGE signature analysis also identified a signature that revealed the molecularly supported link between the MexT regulon and Anr. We designed

  20. Gait Analysis Using Wearable Sensors

    Directory of Open Access Journals (Sweden)

    Hutian Feng

    2012-02-01

    Full Text Available Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phases, the principles and features of wearable sensors used in gait analysis are provided. The gait analysis methods based on wearable sensors is divided into gait kinematics, gait kinetics, and electromyography. Studies on the current methods are reviewed, and applications in sports, rehabilitation, and clinical diagnosis are summarized separately. With the development of sensor technology and the analysis method, gait analysis using wearable sensors is expected to play an increasingly important role in clinical applications.

  1. Gait Analysis Using Wearable Sensors

    Science.gov (United States)

    Tao, Weijun; Liu, Tao; Zheng, Rencheng; Feng, Hutian

    2012-01-01

    Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phases, the principles and features of wearable sensors used in gait analysis are provided. The gait analysis methods based on wearable sensors is divided into gait kinematics, gait kinetics, and electromyography. Studies on the current methods are reviewed, and applications in sports, rehabilitation, and clinical diagnosis are summarized separately. With the development of sensor technology and the analysis method, gait analysis using wearable sensors is expected to play an increasingly important role in clinical applications. PMID:22438763

  2. Safety analysis for research reactors

    International Nuclear Information System (INIS)

    2008-01-01

    The aim of safety analysis for research reactors is to establish and confirm the design basis for items important to safety using appropriate analytical tools. The design, manufacture, construction and commissioning should be integrated with the safety analysis to ensure that the design intent has been incorporated into the as-built reactor. Safety analysis assesses the performance of the reactor against a broad range of operating conditions, postulated initiating events and other circumstances, in order to obtain a complete understanding of how the reactor is expected to perform in these situations. Safety analysis demonstrates that the reactor can be kept within the safety operating regimes established by the designer and approved by the regulatory body. This analysis can also be used as appropriate in the development of operating procedures, periodic testing and inspection programmes, proposals for modifications and experiments and emergency planning. The IAEA Safety Requirements publication on the Safety of Research Reactors states that the scope of safety analysis is required to include analysis of event sequences and evaluation of the consequences of the postulated initiating events and comparison of the results of the analysis with radiological acceptance criteria and design limits. This Safety Report elaborates on the requirements established in IAEA Safety Standards Series No. NS-R-4 on the Safety of Research Reactors, and the guidance given in IAEA Safety Series No. 35-G1, Safety Assessment of Research Reactors and Preparation of the Safety Analysis Report, providing detailed discussion and examples of related topics. Guidance is given in this report for carrying out safety analyses of research reactors, based on current international good practices. The report covers all the various steps required for a safety analysis; that is, selection of initiating events and acceptance criteria, rules and conventions, types of safety analysis, selection of

  3. Fast neutron activation analysis

    International Nuclear Information System (INIS)

    Pepelnik, R.

    1986-01-01

    Since 1981 numerous 14 MeV neutron activation analyses were performed at Korona. On the basis of that work the advantages of this analysis technique and therewith obtained results are compared with other analytical methods. The procedure of activation analysis, the characteristics of Korona, some analytical investigations in environmental research and material physics, as well as sources of systematic errors in trace analysis are described. (orig.) [de

  4. The ATLAS Analysis Architecture

    International Nuclear Information System (INIS)

    Cranmer, K.S.

    2008-01-01

    We present an overview of the ATLAS analysis architecture including the relevant aspects of the computing model and the major architectural aspects of the Athena framework. Emphasis will be given to the interplay between the analysis use cases and the technical aspects of the architecture including the design of the event data model, transient-persistent separation, data reduction strategies, analysis tools, and ROOT interoperability

  5. Dynamical coupled-channel analysis at EBAC. (Excited Baryon Analysis Center)

    International Nuclear Information System (INIS)

    Lee, T.-S.H.; Thomas Jefferson National Accelerator Facility, Newport News, VA

    2008-01-01

    In this contribution, the author reports on the dynamical coupled-channels analysis being pursued at the Excited Baryon Analysis Center (EBAC) of Jefferson Laboratory. EBAC was established in January 2006. Its objective is to extract the parameters associated with the excited states (N*) of the nucleon from the world data of meson production reactions, and to also develop theoretical interpretations of the extracted N* parameters

  6. Citation analysis of meta-analysis articles on posttraumatic stress disorder.

    Science.gov (United States)

    Liao, Xi-Ming; Chen, Ping-Yan

    2011-04-01

    In the past two decades enormously scientific researches on posttraumatic stress disorder (PTSD) have been undertaken and many related meta-analyses have been published. Citation analysis was used to get comprehensive perspectives of meta-analysis articles (MA articles) on PTSD for the purpose of facilitating the researchers, physicians and policy-makers to understand the PTSD. MA articles on PTSD in any languages from January 1980 to March 2009 were included if they presented meta-analytical methods and received at least one citation recorded in the Web of Science (WoS). Whereas studies, in which any effect sizes of PTSD were not distinguished from other psychological disorders, were excluded. Citations to and by identified MA articles were documented basing on records in WoS. Citation analysis was used to examine distribution patterns of characteristics and citation impact of MA articles on PTSD. Canonical analysis was used to explore the relationship between the characteristics of MA articles and citation impact. Thirty-four MA articles published during 1998 and 2008 were identified and revealed multiple study topics on PTSD: 10 (29.4%) were about epidemiology, 13 (38.2%) about treatment or intervention, 6 (17.6%) about pathophysiology or neurophysiology or neuroendocrine, 3 (8.8%) about childhood and 2 (5.9%) about psychosocial adversity. Two articles cited most frequently with 456 and 145 counts were published in Journal of Consulting and Clinical Psychology by Brewin (2000) and Psychological Bulletin by Ozer (2003), respectively. Mean cited count was 7.48 ± 10.56 and mean age (year 2009 minus article publication year) was (4.24 ± 2.91) years. They had been cited approximately by 67 disciplines and by authors from 42 countries or territories. Characteristics of meta-analysis highly correlated with citation impact and reflected by canonical correlation of 0.899 (P < 0.000 01). The age of MA articles predicted their citation impact. Citation analysis would

  7. Clustering analysis

    International Nuclear Information System (INIS)

    Romli

    1997-01-01

    Cluster analysis is the name of group of multivariate techniques whose principal purpose is to distinguish similar entities from the characteristics they process.To study this analysis, there are several algorithms that can be used. Therefore, this topic focuses to discuss the algorithms, such as, similarity measures, and hierarchical clustering which includes single linkage, complete linkage and average linkage method. also, non-hierarchical clustering method, which is popular name K -mean method ' will be discussed. Finally, this paper will be described the advantages and disadvantages of every methods

  8. Reentry analysis

    International Nuclear Information System (INIS)

    Biehl, F.A.

    1984-05-01

    This paper presents the criteria, previous nuclear experience in space, analysis techniques, and possible breakup enhancement devices applicable to an acceptable SP-100 reentry from space. Reactor operation in nuclear-safe orbit will minimize the radiological risk; the remaining safeguards criteria need to be defined. A simple analytical point mass reentry technique and a more comprehensive analysis method that considers vehicle dynamics and orbit insertion malfunctions are presented. Vehicle trajectory, attitude, and possible breakup enhancement devices will be integrated in the simulation as required to ensure an adequate representation of the reentry process

  9. Cluster analysis

    CERN Document Server

    Everitt, Brian S; Leese, Morven; Stahl, Daniel

    2011-01-01

    Cluster analysis comprises a range of methods for classifying multivariate data into subgroups. By organizing multivariate data into such subgroups, clustering can help reveal the characteristics of any structure or patterns present. These techniques have proven useful in a wide range of areas such as medicine, psychology, market research and bioinformatics.This fifth edition of the highly successful Cluster Analysis includes coverage of the latest developments in the field and a new chapter dealing with finite mixture models for structured data.Real life examples are used throughout to demons

  10. NGNP Data Management and Analysis System Analysis and Web Delivery Capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Cynthia D. Gentillon

    2011-09-01

    Projects for the Very High Temperature Reactor (VHTR) Technology Development Office provide data in support of Nuclear Regulatory Commission licensing of the very high temperature reactor. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high-temperature and high-fluence environments. The NGNP Data Management and Analysis System (NDMAS) at the Idaho National Laboratory has been established to ensure that VHTR data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the third NDMAS objective. It describes capabilities for displaying the data in meaningful ways and for data analysis to identify useful relationships among the measured quantities. The capabilities are described from the perspective of NDMAS users, starting with those who just view experimental data and analytical results on the INL NDMAS web portal. Web display and delivery capabilities are described in detail. Also the current web pages that show Advanced Gas Reactor, Advanced Graphite Capsule, and High Temperature Materials test results are itemized. Capabilities available to NDMAS developers are more extensive, and are described using a second series of examples. Much of the data analysis efforts focus on understanding how thermocouple measurements relate to simulated temperatures and other experimental parameters. Statistical control charts and correlation monitoring provide an ongoing assessment of instrument accuracy. Data analysis capabilities are virtually unlimited for those who use the NDMAS web data download capabilities and the analysis software of their choice. Overall, the NDMAS provides convenient data analysis and web delivery capabilities for studying a very large and rapidly increasing database of well-documented, pedigreed data.

  11. Blind Analysis in Particle Physics

    International Nuclear Information System (INIS)

    Roodman, A

    2003-01-01

    A review of the blind analysis technique, as used in particle physics measurements, is presented. The history of blind analyses in physics is briefly discussed. Next the dangers of and the advantages of a blind analysis are described. Three distinct kinds of blind analysis in particle physics are presented in detail. Finally, the BABAR collaboration's experience with the blind analysis technique is discussed

  12. PIXE analysis of thin samples

    International Nuclear Information System (INIS)

    Kiss, Ildiko; Koltay, Ede; Szabo, Gyula; Laszlo, S.; Meszaros, A.

    1985-01-01

    Particle-induced X-ray emission (PIXE) multielemental analysis of thin film samples are reported. Calibration methods of K and L X-lines are discussed. Application of PIXE analysis to aerosol monitoring, multielement aerosol analysis is described. Results of PIXE analysis of samples from two locations in Hungary are compared with the results of aerosol samples from Scandinavia and the USA. (D.Gy.)

  13. Proton exciting X ray analysis

    International Nuclear Information System (INIS)

    Ma Xinpei

    1986-04-01

    The analyzing capability of proton exciting X ray analysis for different elements in organisms was discussed, and dealing with examples of trace element analysis in the human body and animal organisms, such as blood serum, urine, and hair. The sensitivity, accuracy, and capability of multielement analysis were discussed. Its strong points for the trace element analysis in biomedicine were explained

  14. COMPARATIVE ANALYSIS BETWEEN THE FUNDAMENTAL AND TECHNICAL ANALYSIS OF STOCKS

    Directory of Open Access Journals (Sweden)

    Nada Petrusheva

    2016-04-01

    Full Text Available In the world of investing and trading, in order to have a definite advantage and constantly create profit, you need to have a strategic approach. Generally speaking, the two main schools of thought and strategies in financial markets are fundamental and technical analysis. Fundamental and technical analysis differ in several aspects, such as the way of functioning and execution, the time horizon used, the tools used and their objective. These differences lead to certain advantages and disadvantages of each of the analyses. Fundamental and technical analysis are also a subject of critical reviews by the academic and scientific community and many of these reviews concern the methods of their application, i.e. the possibility of combining the two analyses and using them complementarily to fully utilize their strengths and advantages.

  15. Canister storage building hazard analysis report

    International Nuclear Information System (INIS)

    POWERS, T.B.

    1999-01-01

    This report describes the methodology used in conducting the Canister Storage Building (CSB) hazard analysis to support the CSB final safety analysis report (FSAR) and documents the results. The hazard analysis was performed in accordance with the DOE-STD-3009-94, ''Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports'', and meets the intent of HNF-PRO-704, ''Hazard and Accident Analysis Process''. This hazard analysis implements the requirements of DOE Order 5480.23, ''Nuclear Safety Analysis Reports''

  16. Drift Degradation Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Dwayne C. Kicker

    2001-09-28

    A statistical description of the probable block sizes formed by fractures around the emplacement drifts has been developed for each of the lithologic units of the repository host horizon. A range of drift orientations with the drift azimuth varied in 15{sup o} increments has been considered in the static analysis. For the quasi-static seismic analysis, and the time-dependent and thermal effects analysis, two drift orientations have been considered: a drift azimuth of 105{sup o} and the current emplacement drift azimuth of 75{sup o}. The change in drift profile resulting from progressive deterioration of the emplacement drifts has been assessed both with and without backfill. Drift profiles have been determined for four different time increments, including static (i.e., upon excavation), 200 years, 2,000 years, and 10,000 years. The effect of seismic events on rock fall has been analyzed. Block size distributions and drift profiles have been determined for three seismic levels, including a 1,000-year event, a 5,000-year event, and a 10,000-year event. Data developed in this modeling and analysis activity have been entered into the TDMS (DTN: MO0109RDDAAMRR.003). The following conclusions have resulted from this drift degradation analysis: (1) The available fracture data are suitable for supporting a detailed key block analysis of the repository host horizon rock mass. The available data from the north-south Main Drift and the east-west Cross Drift provide a sufficient representative fracture sample of the repository emplacement drift horizon. However, the Tptpln fracture data are only available from a relatively small section of the Cross Drift, resulting in a smaller fracture sample size compared to the other lithologic units. This results in a lower degree of confidence that the key block data based on the Tptpln data set is actually representative of the overall Tptpln key block population. (2) The seismic effect on the rock fall size distribution for all events

  17. Longitudinal analysis of meta-analysis literatures in the database of ISI Web of Science.

    Science.gov (United States)

    Zhu, Changtai; Jiang, Ting; Cao, Hao; Sun, Wenguang; Chen, Zhong; Liu, Jinming

    2015-01-01

    The meta-analysis is regarded as an important evidence for making scientific decision. The database of ISI Web of Science collected a great number of high quality literatures including meta-analysis literatures. However, it is significant to understand the general characteristics of meta-analysis literatures to outline the perspective of meta-analysis. In this present study, we summarized and clarified some features on these literatures in the database of ISI Web of Science. We retrieved the meta-analysis literatures in the database of ISI Web of Science including SCI-E, SSCI, A&HCI, CPCI-S, CPCI-SSH, CCR-E, and IC. The annual growth rate, literature category, language, funding, index citation, agencies and countries/territories of the meta-analysis literatures were analyzed, respectively. A total of 95,719 records, which account for 0.38% (99% CI: 0.38%-0.39%) of all literatures, were found in the database. From 1997 to 2012, the annual growth rate of meta-analysis literatures was 18.18%. The literatures involved in many categories, languages, fundings, citations, publication agencies, and countries/territories. Interestingly, the index citation frequencies of the meta-analysis were significantly higher than that of other type literatures such as multi-centre study, randomize controlled trial, cohort study, case control study, and cases report (Panalysis has been becoming more and more prominent in recent years. In future, in order to promote the validity of meta-analysis, the CONSORT and PRISMA standard should be continuously popularized in the field of evidence-based medicine.

  18. IPAD: the Integrated Pathway Analysis Database for Systematic Enrichment Analysis.

    Science.gov (United States)

    Zhang, Fan; Drabier, Renee

    2012-01-01

    Next-Generation Sequencing (NGS) technologies and Genome-Wide Association Studies (GWAS) generate millions of reads and hundreds of datasets, and there is an urgent need for a better way to accurately interpret and distill such large amounts of data. Extensive pathway and network analysis allow for the discovery of highly significant pathways from a set of disease vs. healthy samples in the NGS and GWAS. Knowledge of activation of these processes will lead to elucidation of the complex biological pathways affected by drug treatment, to patient stratification studies of new and existing drug treatments, and to understanding the underlying anti-cancer drug effects. There are approximately 141 biological human pathway resources as of Jan 2012 according to the Pathguide database. However, most currently available resources do not contain disease, drug or organ specificity information such as disease-pathway, drug-pathway, and organ-pathway associations. Systematically integrating pathway, disease, drug and organ specificity together becomes increasingly crucial for understanding the interrelationships between signaling, metabolic and regulatory pathway, drug action, disease susceptibility, and organ specificity from high-throughput omics data (genomics, transcriptomics, proteomics and metabolomics). We designed the Integrated Pathway Analysis Database for Systematic Enrichment Analysis (IPAD, http://bioinfo.hsc.unt.edu/ipad), defining inter-association between pathway, disease, drug and organ specificity, based on six criteria: 1) comprehensive pathway coverage; 2) gene/protein to pathway/disease/drug/organ association; 3) inter-association between pathway, disease, drug, and organ; 4) multiple and quantitative measurement of enrichment and inter-association; 5) assessment of enrichment and inter-association analysis with the context of the existing biological knowledge and a "gold standard" constructed from reputable and reliable sources; and 6) cross-linking of

  19. Traffic analysis toolbox volume XI : weather and traffic analysis, modeling and simulation.

    Science.gov (United States)

    2010-12-01

    This document presents a weather module for the traffic analysis tools program. It provides traffic engineers, transportation modelers and decisions makers with a guide that can incorporate weather impacts into transportation system analysis and mode...

  20. Reliability on intra-laboratory and inter-laboratory data of hair mineral analysis comparing with blood analysis.

    Science.gov (United States)

    Namkoong, Sun; Hong, Seung Phil; Kim, Myung Hwa; Park, Byung Cheol

    2013-02-01

    Nowadays, although its clinical value remains controversial institutions utilize hair mineral analysis. Arguments about the reliability of hair mineral analysis persist, and there have been evaluations of commercial laboratories performing hair mineral analysis. The objective of this study was to assess the reliability of intra-laboratory and inter-laboratory data at three commercial laboratories conducting hair mineral analysis, compared to serum mineral analysis. Two divided hair samples taken from near the scalp were submitted for analysis at the same time, to all laboratories, from one healthy volunteer. Each laboratory sent a report consisting of quantitative results and their interpretation of health implications. Differences among intra-laboratory and interlaboratory data were analyzed using SPSS version 12.0 (SPSS Inc., USA). All the laboratories used identical methods for quantitative analysis, and they generated consistent numerical results according to Friedman analysis of variance. However, the normal reference ranges of each laboratory varied. As such, each laboratory interpreted the patient's health differently. On intra-laboratory data, Wilcoxon analysis suggested they generated relatively coherent data, but laboratory B could not in one element, so its reliability was doubtful. In comparison with the blood test, laboratory C generated identical results, but not laboratory A and B. Hair mineral analysis has its limitations, considering the reliability of inter and intra laboratory analysis comparing with blood analysis. As such, clinicians should be cautious when applying hair mineral analysis as an ancillary tool. Each laboratory included in this study requires continuous refinement from now on for inducing standardized normal reference levels.