Breeder control fusion reactor. Topical interview

Energy Technology Data Exchange (ETDEWEB)

Schlueter, A [Max-Planck-Institut fuer Plasmaphysik, Garching/Muenchen (Germany, F.R.)

1977-09-01

The energy sources of the future are extremely controversial. The consumption of fossil fuel shall decrease during the next decades, because exhaustion of the resources, pollution, increase of CO/sub 2/ in the atmosphere and other reasons. But at present the question it not yet settled which alternative energy system should replace the fossil fuel. First of all nuclear energy in the form of fission reactions seems to come into operation to a larger extent. The next step may be the controlled thermonuclear fusion reaction. Furthermore, a comparison between fusion and fission is given which shows that fusion would bring about less risks than the breeders. An advantage of the fusion reactor would be the fact that the fuel cycle is closed. Unfortunately, the physical questions are not as yet satisfactorily clarified so that one cannot be sure whether a fusion reactor can really be built.

Radiation symmetry control for inertial confinement fusion capsule implosions in double Z-pinch hohlraums on Z

International Nuclear Information System (INIS)

Vesey, Roger A.; Cuneo, Michael E.; Porter, John L. Jr.; Adams, Richard G.; Aragon, Rafael A.; Rambo, Patrick K.; Ruggles, Laurence E.; Simpson, Walter W.; Smith, Ian C.; Bennett, Guy R.

2003-01-01

The double Z-pinch hohlraum high-yield concept [Hammer et al., Phys. Plasmas 6, 2129 (1999)] utilizes two 63-MA Z pinches to heat separate primary hohlraums at either end of a secondary hohlraum containing the cryogenic fusion capsule. Recent experiments on the Z accelerator [Spielman et al., Phys. Plasmas 5, 2105 (1998)] at Sandia National Laboratories have developed an advanced single-sided power feed, double Z-pinch load to study radiation symmetry and pinch power balance using implosion capsules [Cuneo et al., Phys. Rev. Lett. 88, 215004 (2002)]. Point-projection x-ray imaging with the Z-Beamlet Laser mapped the trajectory and distortion of 2-mm diameter plastic ablator capsules. Using the backlit capsule distortion as a symmetry diagnostic, the ability to predictably tune symmetry at the 2 Legendre mode asymmetry coefficient over a range of ±6% (±2% considering points nearest the optimum) was achieved by varying the length of the cylindrical secondary hohlraum containing the capsule, in agreement with viewfactor and radiation-hydrodynamics simulations

Vesicle fusion with bilayer lipid membrane controlled by electrostatic interaction

Directory of Open Access Journals (Sweden)

Azusa Oshima

2017-09-01

Full Text Available The fusion of proteoliposomes is a promising approach for incorporating membrane proteins in artificial lipid membranes. In this study, we employed an electrostatic interaction between vesicles and supported bilayer lipid membranes (s-BLMs to control the fusion process. We combined large unilamellar vesicles (LUVs containing anionic lipids, which we used instead of proteoliposomes, and s-BLMs containing cationic lipids to control electrostatic interaction. Anionic LUVs were never adsorbed or ruptured on the SiO2 substrate with a slight negative charge, and selectively fused with cationic s-BLMs. The LUVs can be fused effectively to the target position. Furthermore, as the vesicle fusion proceeds and some of the positive charges are neutralized, the attractive interaction weakens and finally the vesicle fusion saturates. In other words, we can control the number of LUVs fused with s-BLMs by controlling the concentration of the cationic lipids in the s-BLMs. The fluidity of the s-BLMs after vesicle fusion was confirmed to be sufficiently high. This indicates that the LUVs attached to the s-BLMs were almost completely fused, and there were few intermediate state vesicles in the fusion process. We could control the position and amount of vesicle fusion with the s-BLMs by employing an electrostatic interaction.

Genetically Controlled Fusion, Exocytosis and Fission of Artificial Vesicles

DEFF Research Database (Denmark)

Bönzli, Eva; Hadorn, Maik; De Lucrezia, Davide

if a special class of viral proteins, termed fusogenic peptides, were added to the external medium. In the present work, we intend to develop genetically controlled fusion, fission and exocytosis of vesicles by the synthesis of peptides within vesicles. First, we enclosed synthesized peptides in vesicles...... to induce in a next step fusion of adjacent vesicles, fission and exocytosis of nested vesicles. Second, we will replace the peptides by an enclosed cell-free expression system to internally synthesize fusion peptides. To control the gene expression, different mechanisms are available, e.g. addition...... fusion, fission and exocytosis....

Impact of an integrated core/SOL description on the R and B T optimization of tokamak fusion reactors

Science.gov (United States)

Siccinio, M.; Fable, E.; Angioni, C.; Saarelma, S.; Scarabosio, A.; Zohm, H.

2018-01-01

An updated and improved version of the 0D divertor and scrape-off layer (SOL) model published in Siccinio et al (2016 Plasma Phys. Control. Fusion 58 125011) was coupled with the 1.5D transport code ASTRA (Pereverzev 1991 IPP Report 5/42, Pereverzev and Yushmanov 2002 IPP Report 5/98 and Fable et al 2013 Plasma Phys. Control. Fusion 55 124028). The resulting numerical tool was employed for various scans in the major radius R and in the toroidal magnetic field B T—for different safety factors q, allowable loop voltages V loop and H factors—in order to identify the most convenient choices for an electricity producing tokamak. Such a scenario analysis was carried out evaluating self-consistently, and simultaneously, the core profile and transport effects, which significantly impact on the fusion power outcome, and the divertor heat loads, which represent one of the most critical issues in view of the realization of fusion power plants (Zohm et al 2013 Nucl. Fusion 53 073019 and Wenninger et al 2017 Nucl. Fusion 57 046002). The main result is that, when divertor limits are enforced, the curves at constant electrical power output are closed on themselves in the R-BT plane, and a maximum achievable power exists—i.e. no benefits would be obtained from a further increase in R and B T once the optimum is reached. This result appears as an intrinsic physical limit for all those devices where a radiative SOL is needed to deal with the power exhaust, and where a lower limit on the power crossing the separatrix (e.g. because of the L-H transition) is present.

Plasma Physics and Controlled Nuclear Fusion Research 1971. Vol. III. Proceedings of the Fourth International Conference on Plasma Physics and Controlled Nuclear Fusion Research

International Nuclear Information System (INIS)

1971-01-01

The ultimate goal of controlled nuclear fusion research is to make a new energy source available to mankind, a source that will be virtually unlimited and that gives promise of being environmentally cleaner than the sources currently exploited. This goal has stimulated research in plasma physics over the past two decades, leading to significant advances in the understanding of matter in its most common state as well as to progress in the confinement and heating of plasma. An indication of this progress is that in several countries considerable effort is being devoted to design studies of fusion reactors and to the technological problems that will be encountered in realizing these reactors. This range of research, from plasma physics to fusion reactor engineering, is shown in the present three-volume publication of the Proceedings of the Fourth Conference on Plasma Physics and Controlled Nuclear Fusion Research. The Conference was sponsored by the International Atomic Energy Agency and was held in Madison, Wisconsin, USA from 17 to 23 June 1971. The enthusiastic co-operation of the University of Wisconsin and of the United States Atomic Energy Commission in the organization of the Conference is gratefully acknowledged. The Conference was attended by over 500 scientists from 24 countries and 3 international organizations, and 143 papers were presented. These papers are published here in the original language; English translations of the Russian papers will be published in a Special Supplement to the journal Nuclear Fusion. The series of conferences on Plasma Physics and Controlled Nuclear Fusion Research has become a major international forum for the presentation and discussion of results in this important and challenging field. In addition to sponsoring these conferences, the International Atomic Energy Agency supports controlled nuclear fusion research by publishing the journal Nuclear Fusion, and has recently established an International Fusion Research Council

Control of tritium permeation through fusion reactor strucural materials

International Nuclear Information System (INIS)

Maroni, V.A.

1978-01-01

The intention of this paper is to provide a brief synopsis of the status of understanding and technology pertaining to the dissolution and permeation of tritium in fusion reactor materials. The following sections of this paper attempt to develop a simple perspective for understanding the consequences of these phenomena and the nature of the technical methodology being contemplated to control their impact on fusion reactor operation. Considered in order are: (1) the occurrence of tritium in the fusion fuel cycle, (2) a set of tentative criteria to guide the analysis of tritium containment and control strategies, (3) the basic mechanisms by which tritium may be released from a fusion plant, and (4) the methods currently under development to control the permeation-related release mechanisms. To provide background and support for these considerations, existing solubility and permeation data for the hydrogen isotopes are compared and correlated under conditions to be expected in fusion reactor systems

Large-scale cryopumping for controlled fusion

International Nuclear Information System (INIS)

Pittenger, L.C.

1977-01-01

Vacuum pumping by freezing out or otherwise immobilizing the pumped gas is an old concept. In several plasma physics experiments for controlled fusion research, cryopumping has been used to provide clean, ultrahigh vacua. Present day fusion research devices, which rely almost universally upon neutral beams for heating, are high gas throughput systems, the pumping of which is best accomplished by cryopumping in the high mass-flow, moderate-to-high vacuum regime. Cryopumping systems have been developed for neutral beam injection systems on several fusion experiments (HVTS, TFTR) and are being developed for the overall pumping of a large, high-throughput mirror containment experiment (MFTF). In operation, these large cryopumps will require periodic defrosting, some schemes for which are discussed, along with other operational considerations. The development of cryopumps for fusion reactors is begun with the TFTR and MFTF systems. Likely paths for necessary further development for power-producing reactors are also discussed

Large-scale cryopumping for controlled fusion

Energy Technology Data Exchange (ETDEWEB)

Pittenger, L.C.

1977-07-25

Vacuum pumping by freezing out or otherwise immobilizing the pumped gas is an old concept. In several plasma physics experiments for controlled fusion research, cryopumping has been used to provide clean, ultrahigh vacua. Present day fusion research devices, which rely almost universally upon neutral beams for heating, are high gas throughput systems, the pumping of which is best accomplished by cryopumping in the high mass-flow, moderate-to-high vacuum regime. Cryopumping systems have been developed for neutral beam injection systems on several fusion experiments (HVTS, TFTR) and are being developed for the overall pumping of a large, high-throughput mirror containment experiment (MFTF). In operation, these large cryopumps will require periodic defrosting, some schemes for which are discussed, along with other operational considerations. The development of cryopumps for fusion reactors is begun with the TFTR and MFTF systems. Likely paths for necessary further development for power-producing reactors are also discussed.

Studies on the robustness of shock-ignited laser fusion targets

International Nuclear Information System (INIS)

Atzeni, S; Schiavi, A; Marocchino, A

2011-01-01

Several aspects of the sensitivity of a shock-ignited inertial fusion target to variation of parameters and errors or imperfections are studied by means of one-dimensional and two-dimensional numerical simulations. The study refers to a simple all-DT target, initially proposed for fast ignition (Atzeni et al 2007 Phys. Plasmas 7 052702) and subsequently shown to be also suitable for shock ignition (Ribeyre et al 2009 Plasma Phys. Control. Fusion 51 015013). It is shown that the growth of both Richtmyer-Meshkov and Rayleigh-Taylor instability (RTI) at the ablation front is reduced by laser pulses with an adiabat-shaping picket. An operating window for the parameters of the ignition laser spike is described; the threshold power depends on beam focusing and synchronization with the compression pulse. The time window for spike launch widens with beam power, while the minimum spike energy is independent of spike power. A large parametric scan indicates good tolerance (at the level of a few percent) to target mass and laser power errors. 2D simulations indicate that the strong igniting shock wave plays an important role in reducing deceleration-phase RTI growth. Instead, the high hot-spot convergence ratio (ratio of initial target radius to hot-spot radius at ignition) makes ignition highly sensitive to target mispositioning.

The potential role of electric fields and plasma barodiffusion on the inertial confinement fusion databasea)

Science.gov (United States)

Amendt, Peter; Wilks, S. C.; Bellei, C.; Li, C. K.; Petrasso, R. D.

2011-05-01

The generation of strong, self-generated electric fields (GV/m) in direct-drive, inertial-confinement-fusion (ICF) capsules has been reported [Rygg et al., Science 319, 1223 (2008); Li et al., Phys. Rev. Lett. 100, 225001 (2008)]. A candidate explanation for the origin of these fields based on charge separation across a plasma shock front was recently proposed [Amendt et al., Plasma Phys. Controlled Fusion 51 124048 (2009)]. The question arises whether such electric fields in imploding capsules can have observable consequences on target performance. Two well-known anomalies come to mind: (1) an observed ≈2× greater-than-expected deficit of neutrons in an equimolar D3He fuel mixture compared with hydrodynamically equivalent D [Rygg et al., Phys. Plasmas 13, 052702 (2006)] and DT [Herrmann et al., Phys. Plasmas 16, 056312 (2009)] fuels, and (2) a similar shortfall of neutrons when trace amounts of argon are mixed with D in indirect-drive implosions [Lindl et al., Phys. Plasmas 11, 339 (2004)]. A new mechanism based on barodiffusion (or pressure gradient-driven diffusion) in a plasma is proposed that incorporates the presence of shock-generated electric fields to explain the reported anomalies. For implosions performed at the Omega laser facility [Boehly et al., Opt. Commun. 133, 495 (1997)], the (low Mach number) return shock has an appreciable scale length over which the lighter D ions can diffuse away from fuel center. The depletion of D fuel is estimated and found to lead to a corresponding reduction in neutrons, consistent with the anomalies observed in experiments for both argon-doped D fuels and D3He equimolar mixtures. The reverse diffusional flux of the heavier ions toward fuel center also increases the pressure from a concomitant increase in electron number density, resulting in lower stagnation pressures and larger imploded cores in agreement with gated, self-emission, x-ray imaging data.

Computer applications in controlled fusion research

International Nuclear Information System (INIS)

Killeen, J.

1975-02-01

The role of Nuclear Engineering Education in the application of computers to controlled fusion research can be a very important one. In the near future the use of computers in the numerical modelling of fusion systems should increase substantially. A recent study group has identified five categories of computational models to study the physics of magnetically confined plasmas. A comparable number of types of models for engineering studies are called for. The development and application of computer codes to implement these models is a vital step in reaching the goal of fusion power. In order to meet the needs of the fusion program the National CTR Computer Center has been established at the Lawrence Livermore Laboratory. A large central computing facility is linked to smaller computing centers at each of the major CTR laboratories by a communications network. The crucial element that is needed for success is trained personnel. The number of people with knowledge of plasma science and engineering that are trained in numerical methods and computer science is quite small, and must be increased substantially in the next few years. Nuclear Engineering departments should encourage students to enter this field and provide the necessary courses and research programs in fusion computing. (U.S.)

Computer applications in controlled fusion research

International Nuclear Information System (INIS)

Killeen, J.

1975-01-01

The application of computers to controlled thermonuclear research (CTR) is essential. In the near future the use of computers in the numerical modeling of fusion systems should increase substantially. A recent panel has identified five categories of computational models to study the physics of magnetically confined plasmas. A comparable number of types of models for engineering studies is called for. The development and application of computer codes to implement these models is a vital step in reaching the goal of fusion power. To meet the needs of the fusion program the National CTR Computer Center has been established at the Lawrence Livermore Laboratory. A large central computing facility is linked to smaller computing centers at each of the major CTR Laboratories by a communication network. The crucial element needed for success is trained personnel. The number of people with knowledge of plasma science and engineering trained in numerical methods and computer science must be increased substantially in the next few years. Nuclear engineering departments should encourage students to enter this field and provide the necessary courses and research programs in fusion computing

Plasma physics and controlled fusion research during half a century

Energy Technology Data Exchange (ETDEWEB)

Lehnert, Bo

2001-06-01

A review is given on the historical development of research on plasma physics and controlled fusion. The potentialities are outlined for fusion of light atomic nuclei, with respect to the available energy resources and the environmental properties. Various approaches in the research on controlled fusion are further described, as well as the present state of investigation and future perspectives, being based on the use of a hot plasma in a fusion reactor. Special reference is given to the part of this work which has been conducted in Sweden, merely to identify its place within the general historical development. Considerable progress has been made in fusion research during the last decades. Temperatures above the limit for ignition of self-sustained fusion reactions, i.e. at more than hundred million degrees, have been reached in large experiments and under conditions where the fusion power generation is comparable to the power losses. An energy producing fusion reactor could in principle be realized already today, but it would not become technically and economically efficient when being based on the present state of art. Future international research has therefore to be conducted along broad lines, with necessary ingredients of basic investigations and new ideas.

Plasma physics and controlled fusion research during half a century

International Nuclear Information System (INIS)

Lehnert, Bo

2001-06-01

A review is given on the historical development of research on plasma physics and controlled fusion. The potentialities are outlined for fusion of light atomic nuclei, with respect to the available energy resources and the environmental properties. Various approaches in the research on controlled fusion are further described, as well as the present state of investigation and future perspectives, being based on the use of a hot plasma in a fusion reactor. Special reference is given to the part of this work which has been conducted in Sweden, merely to identify its place within the general historical development. Considerable progress has been made in fusion research during the last decades. Temperatures above the limit for ignition of self-sustained fusion reactions, i.e. at more than hundred million degrees, have been reached in large experiments and under conditions where the fusion power generation is comparable to the power losses. An energy producing fusion reactor could in principle be realized already today, but it would not become technically and economically efficient when being based on the present state of art. Future international research has therefore to be conducted along broad lines, with necessary ingredients of basic investigations and new ideas

Closed loop control of the sawtooth instability in nuclear fusion

NARCIS (Netherlands)

Witvoet, G.; Steinbuch, M.; Westerhof, E.; Doelman, N.J.; Baar, de M.R.

2010-01-01

In nuclear fusion the sawtooth instability is an important plasma phenomenon, having both positive and negative effects on the tokamak plasma. Control of its period is essential in future nuclear fusion reactors. This paper presents a control oriented model of the sawtooth instability, with current

Remote control of a fusion facility

Energy Technology Data Exchange (ETDEWEB)

Schissel, D.P. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States)], E-mail: schissel@fusion.gat.com; Abla, G.; Humphreys, D.A.; Penaflor, B.G.; Sammuli, B.S.; Walker, M.L. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States)

2009-06-15

Magnetic fusion experiments keep growing in size and complexity resulting in a concurrent growth in collaboration between experimental sites and laboratories worldwide. This scientific collaboration activity is strong at existing experimental sites, is a major element of machines just coming on line, and is also a thrust of experiments that will come on line in the next decade. Computer science research into enhancing the ability to scientifically participate in a fusion experiment remotely has been growing in size in an attempt to better address the needs of fusion scientists worldwide. The natural progression of this research is to examine how to move from remote scientific participation to remote hardware control. This paper examines the challenges associated with remote experimental device control and proposes a solution based on a semantic approach that defines a Gatekeeper software system that will be the only channel of interaction for incoming requests to the experimental site. The role of the Gatekeeper is to validate the identification and access privilege of the requestor and to ensure the validity of the proposed request. The Gatekeeper will be a modular system, transparent to end-users, and allow a high volume of activity.

Remote control of a fusion facility

International Nuclear Information System (INIS)

Schissel, D.P.; Abla, G.; Humphreys, D.A.; Penaflor, B.G.; Sammuli, B.S.; Walker, M.L.

2009-01-01

Magnetic fusion experiments keep growing in size and complexity resulting in a concurrent growth in collaboration between experimental sites and laboratories worldwide. This scientific collaboration activity is strong at existing experimental sites, is a major element of machines just coming on line, and is also a thrust of experiments that will come on line in the next decade. Computer science research into enhancing the ability to scientifically participate in a fusion experiment remotely has been growing in size in an attempt to better address the needs of fusion scientists worldwide. The natural progression of this research is to examine how to move from remote scientific participation to remote hardware control. This paper examines the challenges associated with remote experimental device control and proposes a solution based on a semantic approach that defines a Gatekeeper software system that will be the only channel of interaction for incoming requests to the experimental site. The role of the Gatekeeper is to validate the identification and access privilege of the requestor and to ensure the validity of the proposed request. The Gatekeeper will be a modular system, transparent to end-users, and allow a high volume of activity.

Atomic and molecular physics of controlled thermonuclear fusion

International Nuclear Information System (INIS)

Joachain, C.J.; Post, D.E.

1983-01-01

This book attempts to provide a comprehensive introduction to the atomic and molecular physics of controlled thermonuclear fusion, and also a self-contained source from which to start a systematic study of the field. Presents an overview of fusion energy research, general principles of magnetic confinement, and general principles of inertial confinement. Discusses the calculation and measurement of atomic and molecular processes relevant to fusion, and the atomic and molecular physics of controlled thermonuclear research devices. Topics include recent progress in theoretical methods for atomic collisions; current theoretical techniques for electron-atom and electronion scattering; experimental aspects of electron impact ionization and excitation of positive ions; the theory of charge exchange and ionization by heavy particles; experiments on electron capture and ionization by multiply charged ions; Rydberg states; atomic and molecular processes in high temperature, low-density magnetically confined plasmas; atomic processes in high-density plasmas; the plasma boundary region and the role of atomic and molecular processes; neutral particle beam production and injection; spectroscopic plasma diagnostics; and particle diagnostics for magnetic fusion experiments

Applications of intelligent-measurement systems in controlled-fusion research

International Nuclear Information System (INIS)

Owen, E.W.; Shimer, D.W.; Lindquist, W.B.; Peterson, R.L.; Wyman, R.H.

1981-01-01

The paper describes the control and instrumentation for the Mirror Fusion Test Facility at the Lawrence Livermore National Laboratory, California, USA. This large-scale scientific experiment in controlled thermonuclear fusion, which is currently being expanded, originally had 3000 devices to control and 7000 sensors to monitor. A hierarchical computer control system, is used with nine minicomputers forming the supervisory system. There are approximately 55 local control and instrumentation microcomputers. In addition, each device has its own monitoring equipment, which in some cases consists of a small computer. After describing the overall system a more detailed account is given of the control and instrumentation for two large superconducting magnets

Remotely controlled fusion of selected vesicles and living cells: a key issue review

Science.gov (United States)

Bahadori, Azra; Moreno-Pescador, Guillermo; Oddershede, Lene B.; Bendix, Poul M.

2018-03-01

Remote control over fusion of single cells and vesicles has a great potential in biological and chemical research allowing both transfer of genetic material between cells and transfer of molecular content between vesicles. Membrane fusion is a critical process in biology that facilitates molecular transport and mixing of cellular cytoplasms with potential formation of hybrid cells. Cells precisely regulate internal membrane fusions with the aid of specialized fusion complexes that physically provide the energy necessary for mediating fusion. Physical factors like membrane curvature, tension and temperature, affect biological membrane fusion by lowering the associated energy barrier. This has inspired the development of physical approaches to harness the fusion process at a single cell level by using remotely controlled electromagnetic fields to trigger membrane fusion. Here, we critically review various approaches, based on lasers or electric pulses, to control fusion between individual cells or between individual lipid vesicles and discuss their potential and limitations for present and future applications within biochemistry, biology and soft matter.

Controlled nuclear fusion. Theoretical and technical-physical aspects

International Nuclear Information System (INIS)

Donne, T.; Oomens, N.

1995-01-01

It is stated that the realization of controlled fusion is not only a matter of solving technical problems. Also theoretical research in the field of plasma physics is required. A brief state-of-the-art is given of theoretical and technical-physical aspects of nuclear fusion. Attention is paid to magnetic confinement, the importance of theoretical research, plasma heating, plasma diagnostics, and the control of plasma transport. Throughout the article special attention is paid to the International Thermonuclear Experimental Reactor (ITER) project. 5 figs., 1 tab., 3 refs

Laser Fusion: status, future, and tritium control

International Nuclear Information System (INIS)

Coyle, P.E.

1978-11-01

At Livermore the 10 kJ, 20 to 30 TW Shiva facility is now operational and producing regular new fusion results. Design work has begun on a 200 to 300 TW laser designed to carry the program through the first breakeven demonstration experiments in the mid-1980's. Confidence in reaching this goal is based on the significant progress we have made in state-of-the-art, high-power Nd:glass laser technology, in experimental laser fusion and laser plasma interaction physics, and in theoretical and analytical computer codes which reliably model and predict experimental results. For all of these experiments, a variety of fusion targets are being fabricated in the laboratory, and the control and handling of tritium is now a regular and routine part of ongoing inertial fusion experiments. Target design with gains of about 1000 have been studied and the means to mass produce such pellets at low cost are also being developed

Controlled fusion and plasma physics

International Nuclear Information System (INIS)

1994-07-01

40 papers are presented at this 21. conference on controlled fusion and plasma physics (JET). Titles are: effects of sawtooth crashes on beams ions and fusion product tritons; beta limits in H-modes and VH-modes; impurity induced neutralization of MeV energy protons in JET plasmas; lost α particle diagnostic for high-yield D-T fusion plasmas; 15-MeV proton emission from ICRF-heated plasmas; pulse compression radar reflectometry for density measurements; gamma-ray emission profile measurements during ICRH discharges; the new JET phase ICRH array; simulation of triton burn-up; parametric dependencies of JET electron temperature profiles; detached divertor plasmas; excitation of global Alfven Eigenmodes by RF heating; mechanisms of toroidal rotation; effect of shear in the radial electric field on confinement; plasma transport properties at the L-H transition; numerical study of plasma detachment conditions in JET divertor plasmas; the SOL width and the MHD interchange instability; non linear magnetic reconnection in low collisionality plasmas; topology and slowing down of high energy ion orbits; sawtooth crashes at high beta; fusion performances and alpha heating in future JET D-T plasmas; a stable route to high-beta plasmas with non-monotonic q-profiles; theory of propagation of changes to confinement; spatial distribution of gamma emissivity and fast ions during ICRF heating; multi-camera soft X-ray diagnostic; radiation phenomena and particle fluxes in the X-event; local measurement of transport parameters for laser injected trace impurities; impurity transport of high performance discharges; negative snakes and negative shear; neural-network charge exchange analysis; ion temperature anisotropy in helium neutral beam fuelling; impurity line emission due to thermal charge exchange in edge plasmas; control of convection by fuelling and pumping; VH mode accessibility and global H-mode properties; ion cyclotron emission by spontaneous emission; LHCD/ICRH synergy

The development of controlled nuclear fusion

International Nuclear Information System (INIS)

Pease, R.S.

1978-01-01

The high temperature conditions needed in a controlled nuclear fusion reactor are now being approached in experiments using magnetic fields to confine and isolate the plasma, especially in systems of the tokamak type. The underlying reasons for the successes are discussed and it is concluded that the remaining advances needed in temperature and thermal insulation may well be achieved in new large tokamak experiments now under construction. Comparable progress is being made also in inertial confinement systems; key experiments on achieving the required super-high densities with high-powered pulsed laser systems are about to commence. To achieve fusion reactors will require the combination of three major disciplines: plasma physics, electromechanical engineering and nuclear engineering. Proposals have been made for an international study group to be set up under the IAEA auspices to consider technical objectives and the nature of the next large fusion device which could be constructed internationally, and in which this synthesis could be attempted. (author)

Controlled Nuclear Fusion.

Science.gov (United States)

Glasstone, Samuel

This publication is one of a series of information booklets for the general public published by The United States Atomic Energy Commission. Among the topics discussed are: Importance of Fusion Energy; Conditions for Nuclear Fusion; Thermonuclear Reactions in Plasmas; Plasma Confinement by Magnetic Fields; Experiments With Plasmas; High-Temperature…

Plasma physics and controlled nuclear fusion research 1988. V.3

International Nuclear Information System (INIS)

1989-01-01

Volume 3 of the proceedings of the twelfth international conference on plasma physics and controlled nuclear fusion, held in Nice, France, 12-19 October, 1988, contains papers presented on inertial fusion. Direct and indirect laser implosion experiments, programs of laser construction, computer modelling of implosions and resulting plasmas, and light ion beam fusion experiments are discussed. Refs, figs and tabs

Controlled thermonuclear fusion

CERN Document Server

Bobin, Jean Louis

2014-01-01

The book is a presentation of the basic principles and main achievements in the field of nuclear fusion. It encompasses both magnetic and inertial confinements plus a few exotic mechanisms for nuclear fusion. The state-of-the-art regarding thermonuclear reactions, hot plasmas, tokamaks, laser-driven compression and future reactors is given.

PhysLink Physics and Astronomy online education and reference

CERN Document Server

The PhysLink.com is a comprehensive physics and astronomy online education, research and reference web site. In addition to providing high-quality content, PhysLink.com is a meeting place for professionals, students and other curious minds.

Controlled nuclear fusion, a challenging task with a big payoff

International Nuclear Information System (INIS)

Noterdaeme, Jean-Marie

2003-01-01

Controlled thermonuclear fusion carries the promise of providing the world with a new source of energy, the same energy that powers the stars. Research in this area has progressed steadily for several decades now, and is ready to move into a new phase. The probability is high that a new international experimental machine (ITER) which will prove the scientific and technological feasibility of fusion energy, will be built. This paper introduces nuclear fusion for people familiar with the fission process. It starts from the basic principles common to fusion and fission. It moves on to point out the differences, explains the reasons for those differences and the consequences. Controlled thermonuclear fusion can be obtained in several ways, which have led to different research lines. One line, on which this talk focuses, is by confining the reacting particles with magnetic fields. Another, which is the subject of a different talk, relies on the inertia of the particles to create the conditions necessary for fusion. The progress of the magnetic confinement research is shown, with examples of major hurdles, which have occurred and have been overcome. Recent results, which make us optimistic that the next machine can prove the feasibility of fusion energy, are highlighted. The talk also addresses the challenges that remain before us, and suggests that the promise of fusion energy opens up new perspectives and opportunities for the development and the use of fission energy. (author)

Genetically controlled fusion, exocytosis and fission of artificial vesicles-a roadmap

DEFF Research Database (Denmark)

Bönzli, Eva; Hadorn, Maik; de Lucrezia, Davide

2011-01-01

were shown to fuse if a special class of viral proteins, termed fusogenic peptides, were added to the external medium (Nomura et al. 2004). In the present work, we intend to develop genetically controlled fusion, fission and exocytosis of vesicles by the synthesis of peptides within vesicles. First, we...... enclosed synthesized peptides in vesicles to induce in a next step fusion of adjacent vesicles, fission and exocytosis of nested vesicles. Second, we will replace the peptides by an enclosed cell-free expression system to internally synthesize fusion peptides. To control the gene expression, different...

Status report on controlled nuclear fusion as a source of hydrogen energy

International Nuclear Information System (INIS)

Powell, J.

1975-01-01

The present status of controlled fusion research is reviewed. Possible future reseach is also described. Tokamak systems using both fusion and fissionable fuels are discussed. Various aspects of hydrogen production by fusion reactors are described according to cost and economics. auth)

The fusion rules for the Temperley–Lieb algebra and its dilute generalization

International Nuclear Information System (INIS)

Belletête, Jonathan

2015-01-01

The Temperley–Lieb (TL) family of algebras is well known for its role in building integrable lattice models. Even though a proof is still missing, it is agreed that these models should go to conformal field theories in the thermodynamic limit and that the limiting vector space should carry a representation of the Virasoro algebra. The fusion rules are a notable feature of the Virasoro algebra. One would hope that there is an analogous construction for the TL family. Such a construction was proposed by Read and Saleur (2007 Nucl. Phys. B 777 316) and partially computed by Gainutdinov and Vasseur (2013 Nucl. Phys. B 868 223–70) using the bimodule structure over the TL algebras and the quantum group Uq (sl2).We use their definition for the dilute Temperley–Lieb (dTL) family, a generalization of the original TL family. We develop a new way of computing fusion by using induction and show its power by obtaining fusion rules for both dTL and TL. We recover those computed by Gainutdivov and Vasseur and new ones that were beyond their scope. In particular, we identify a set of irreducible TL- or dTL-representations whose behavior under fusion is that of some irreducibles of the minimal models of conformal field theory. (paper)

Information Fusion-Based Optimal Attitude Control for an Alterable Thrust Direction Unmanned Aerial Vehicle

Directory of Open Access Journals (Sweden)

Ziyang Zhen

2013-01-01

Full Text Available Attitude control is the inner-loop and the most important part of the automatic flight control system of an unmanned aerial vehicle (UAV. The information fusion-based optimal control method is applied in a UAV flight control system in this work. Firstly, a nonlinear model of alterable thrust direction UAV (ATD-UAV is established and linearized for controller design. The longitudinal controller and lateral controller are respectively designed based on information fusion-based optimal control, and then the information fusion flight control system is built up. Finally, the simulation of a nonlinear model described as ATD-UAV is carried out, the results of which show the superiority of the information fusion-based control strategy when compared to the single-loop design method. We also show that the ATD technique improves the anti-disturbance capacity of the UAV.

Thermonuclear controlled fusion: international cooperation

International Nuclear Information System (INIS)

Conscience, J.-F.

2001-01-01

This report summarizes the current worldwide status of research in the field of thermonuclear controlled fusion as well as the international research programme planed for the next decades. The two main projects will be the ITER facility (International Thermonuclear Experimental Reactor) that should produce 10 times more energy than the energy injected, and the IFMIF (International Fusion Materials Irradiation Facility) designed to study the reactions of materials under intense neutron fluxes. The future of the pioneering JET facility (Joint European Torus) is also discussed. The engagement of the various countries (USA, Japan, Germany, Russian Federation and Canada) and international organisations (EURATOM and IEA) in terms of investment and research is described. Switzerland is involved in this program through an agreement with EURATOM and is mainly dedicated to experimental studies with the TCV machine in Lausanne and numerical studies of plasma configurations. It will participate to the development of the microwave plasma heating system for the ITER machine

Dispersion interferometer for controlled fusion devices

International Nuclear Information System (INIS)

Drachev, V.P.; Krasnikov, Yu.I.; Bagryansky, P.A.

1992-01-01

A common feature in interferometry is the presence of two independent optical channels. Since wave phase in a medium depends on the geometrical path, polarization and radiation frequency, respectively, one can distinguish three types of interferometric schemes when the channels are geometrically separated, or separation occurs in polarizations or radiation frequencies. We have developed a measurement scheme based on a dispersion interferometer (DI) for plasma diagnostics in the experiments on controlled fusion. DI optical channels have the same geometrical path and are separated in radiation frequency. Use of a common optical path causes the main advantage of the DI technique - low sensitivity to vibrations of optical elements. The use of the DI technique for diagnostics of a laser spark in air and of arc discharges has shown its essential advantages as compared to classical interferometers. Interest in the DI technique from the viewpoint of its application in controlled fusion devices is determined also generated by the possibility of developing a compact multichannel interferometer not requiring a vibration isolation structure. (author) 14 refs., 3 figs

Anomaly Detection for Resilient Control Systems Using Fuzzy-Neural Data Fusion Engine

Energy Technology Data Exchange (ETDEWEB)

Ondrej Linda; Milos Manic; Timothy R. McJunkin

2011-08-01

Resilient control systems in critical infrastructures require increased cyber-security and state-awareness. One of the necessary conditions for achieving the desired high level of resiliency is timely reporting and understanding of the status and behavioral trends of the control system. This paper describes the design and development of a neural-network based data-fusion system for increased state-awareness of resilient control systems. The proposed system consists of a dedicated data-fusion engine for each component of the control system. Each data-fusion engine implements three-layered alarm system consisting of: (1) conventional threshold-based alarms, (2) anomalous behavior detector using self-organizing maps, and (3) prediction error based alarms using neural network based signal forecasting. The proposed system was integrated with a model of the Idaho National Laboratory Hytest facility, which is a testing facility for hybrid energy systems. Experimental results demonstrate that the implemented data fusion system provides timely plant performance monitoring and cyber-state reporting.

Fusion proton diagnostic for the C-2 field reversed configurationa)

Science.gov (United States)

Magee, R. M.; Clary, R.; Korepanov, S.; Smirnov, A.; Garate, E.; Knapp, K.; Tkachev, A.

2014-11-01

Measurements of the flux of fusion products from high temperature plasmas provide valuable insights into the ion energy distribution, as the fusion reaction rate is a very sensitive function of ion energy. In C-2, where field reversed configuration plasmas are formed by the collision of two compact toroids and partially sustained by high power neutral beam injection [M. Binderbauer et al., Phys. Rev. Lett. 105, 045003 (2010); M. Tuszewski et al., Phys. Rev. Lett. 108, 255008 (2012)], measurements of DD fusion neutron flux are used to diagnose ion temperature and study fast ion confinement and dynamics. In this paper, we will describe the development of a new 3 MeV proton detector that will complement existing neutron detectors. The detector is a large area (50 cm2), partially depleted, ion implanted silicon diode operated in a pulse counting regime. While the scintillator-based neutron detectors allow for high time resolution measurements (˜100 kHz), they have no spatial or energy resolution. The proton detector will provide 10 cm spatial resolution, allowing us to determine if the axial distribution of fast ions is consistent with classical fast ion theory or whether anomalous scattering mechanisms are active. We will describe in detail the diagnostic design and present initial data from a neutral beam test chamber.

The ORNL Controlled Fusion Atomic Data Center

International Nuclear Information System (INIS)

Schultz, D.R.; Krstic, P.S.; Ownby, F.M.; Meyer, F.W.; Havener, C.C.; Bannister, M.E.; Liu, W.; Jeffery, D.J.; Stancil, P.C.

1997-01-01

The principal mission of the Controlled Fusion Atomic Data Center is the collection evaluation, and dissemination of atomic collision data relevant to fusion energy development. With the advent of the widespread use of the World Wide Web, the data center's resources are being placed on-line to facilitate their use by end-users (cf. http://www-cfadc.phy.ornl.gov/). As this development continues, initially disparate, individually compiled resources will be transformed into integrated tools for retrieving recommended data, or displaying and manipulating the information available. The data center's present capabilities, recent data production/evaluation efforts, and goals for future development are highlighted here

Surface effects in controlled thermonuclear fusion

International Nuclear Information System (INIS)

Kaminsky, M.

1975-08-01

During the operation of large size plasma facilities and future controlled thermonuclear fusion reactors the surfaces of such major components as container walls, beam limiters, diverter walls and beam-dump walls of the injector region will be exposed to particle and photon bombardment from primary plasma radiations and from secondary radiations. Such radiations can cause, for example, physical and chemical sputtering, blistering, particle- and photon-impact induced desorption, secondary electron and x-ray emission, backscattering, nuclear reactions, photo-decomposition of surface compounds, photocatalysis, and vaporization. Such effects in turn can (a) seriously damage and erode the bombarded surface and (b) release major quantities of impurities which will contaminate the plasma. The effects of some of the major surface phenomena on the operation of plasma facilities and future fusion reactors are discussed

Plasma physics for controlled fusion. 2. ed.

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, Kenro

2016-08-01

This new edition presents the essential theoretical and analytical methods needed to understand the recent fusion research of tokamak and alternate approaches. The author describes magnetohydrodynamic and kinetic theories of cold and hot plasmas in detail. The book covers new important topics for fusion studies such as plasma transport by drift turbulence, which depend on the magnetic configuration and zonal flows. These are universal phenomena of microturbulence. They can modify the onset criterion for turbulent transport, instabilities driven by energetic particles as well as alpha particle generation and typical plasma models for computer simulation. The fusion research of tokamaks with various new versions of H modes are explained. The design concept of ITER, the international tokamak experimental reactor, is described for inductively driven operations as well as steady-state operations using non-inductive drives. Alternative approaches of reversed-field pinch and its relaxation process, stellator including quasi-symmetric system, open-end system of tandem mirror and inertial confinement are also explained. Newly added and updated topics in this second edition include zonal flows, various versions of H modes, and steady-state operations of tokamak, the design concept of ITER, the relaxation process of RFP, quasi-symmetric stellator, and tandem mirror. The book addresses graduate students and researchers in the field of controlled fusion.

Plasma physics for controlled fusion. 2. ed.

International Nuclear Information System (INIS)

Miyamoto, Kenro

2016-01-01

This new edition presents the essential theoretical and analytical methods needed to understand the recent fusion research of tokamak and alternate approaches. The author describes magnetohydrodynamic and kinetic theories of cold and hot plasmas in detail. The book covers new important topics for fusion studies such as plasma transport by drift turbulence, which depend on the magnetic configuration and zonal flows. These are universal phenomena of microturbulence. They can modify the onset criterion for turbulent transport, instabilities driven by energetic particles as well as alpha particle generation and typical plasma models for computer simulation. The fusion research of tokamaks with various new versions of H modes are explained. The design concept of ITER, the international tokamak experimental reactor, is described for inductively driven operations as well as steady-state operations using non-inductive drives. Alternative approaches of reversed-field pinch and its relaxation process, stellator including quasi-symmetric system, open-end system of tandem mirror and inertial confinement are also explained. Newly added and updated topics in this second edition include zonal flows, various versions of H modes, and steady-state operations of tokamak, the design concept of ITER, the relaxation process of RFP, quasi-symmetric stellator, and tandem mirror. The book addresses graduate students and researchers in the field of controlled fusion.

Controlled fusion and plasma heating

International Nuclear Information System (INIS)

1990-06-01

The contributions presented in the 17th European Conference on Controlled Fusion and Plasma Heating were focused on Tore Supra investigations. The following subjects were presented: ohmic discharges, lower hybrid experiments, runaway electrons, Thomson scattering, plasma density measurements, magnetic fluctuations, polarization scattering, plasma currents, plasma fluctuation measurements, evaporation of hydrogen pellets in presence of fast electrons, ripple induced stochastic diffusion of trapped particles, tearing mode stabilization, edge effects on turbulence behavior, electron cyclotron heating, micro-tearing modes, divertors, limiters

Plasma surface interactions in controlled fusion devices

Energy Technology Data Exchange (ETDEWEB)

Ghendrih, Ph.; Becoulet, M.; Costanzo, L. [and others

2000-07-01

This report brings together all the contributions of EURATOM/CEA association to the 14. international conference on plasma surface interactions in controlled fusion devices. 24 papers are presented and they deal mainly with the ergodic divertor and the first wall of Tore-supra tokamak.

Plasma surface interactions in controlled fusion devices

International Nuclear Information System (INIS)

Ghendrih, Ph.; Becoulet, M.; Costanzo, L.

2000-07-01

This report brings together all the contributions of EURATOM/CEA association to the 14. international conference on plasma surface interactions in controlled fusion devices. 24 papers are presented and they deal mainly with the ergodic divertor and the first wall of Tore-supra tokamak

Physics of plasma-wall interactions in controlled fusion

International Nuclear Information System (INIS)

Post, D.E.; Behrisch, R.

1984-01-01

In the areas of plasma physics, atomic physics, surface physics, bulk material properties and fusion experiments and theory, the following topics are presented: the plasma sheath; plasma flow in the sheath and presheath of a scrape-off layer; probes for plasma edge diagnostics in magnetic confinement fusion devices; atomic and molecular collisions in the plasma boundary; physical sputtering of solids at ion bombardment; chemical sputtering and radiation enhanced sublimation of carbon; ion backscattering from solid surfaces; implantation, retention and release of hydrogen isotopes; surface erosion by electrical arcs; electron emission from solid surfaces;l properties of materials; plasma transport near material boundaries; plasma models for impurity control experiments; neutral particle transport; particle confinement and control in existing tokamaks; limiters and divertor plates; advanced limiters; divertor tokamak experiments; plasma wall interactions in heated plasmas; plasma-wall interactions in tandem mirror machines; and impurity control systems for reactor experiments

Particle and impurity control in toroidal fusion devices

International Nuclear Information System (INIS)

Wootton, A.J.

1986-01-01

A review of working particle and impurity control techniques used in and proposed for magnetic fusion devices is presented. The requirements of both present-day machines and envisaged fusion reactors are considered. The various techniques which have been proposed are characterized by whether they affect sources, sinks, or fluxes; in many cases a particular method or device can appear in more than one category. Examples are drawn from published results. The solutions proposed for the large devices which will be operating during the next 5 years are discussed

Fusion Control of Flexible Logic Control and Neural Network

Directory of Open Access Journals (Sweden)

Lihua Fu

2014-01-01

Full Text Available Based on the basic physical meaning of error E and error variety EC, this paper analyzes the logical relationship between them and uses Universal Combinatorial Operation Model in Universal Logic to describe it. Accordingly, a flexible logic control method is put forward to realize effective control on multivariable nonlinear system. In order to implement fusion control with artificial neural network, this paper proposes a new neuron model of Zero-level Universal Combinatorial Operation in Universal Logic. And the artificial neural network of flexible logic control model is implemented based on the proposed neuron model. Finally, stability control, anti-interference control of double inverted-pendulum system, and free walking of cart pendulum system on a level track are realized, showing experimentally the feasibility and validity of this method.

Optimal control theory applied to fusion plasma thermal stabilization

International Nuclear Information System (INIS)

Sager, G.; Miley, G.; Maya, I.

1985-01-01

Many authors have investigated stability characteristics and performance of various burn control schemes. The work presented here represents the first application of optimal control theory to the problem of fusion plasma thermal stabilization. The objectives of this initial investigation were to develop analysis methods, demonstrate tractability, and present some preliminary results of optimal control theory in burn control research

Transport and Dynamics in Toroidal Fusion Systems

International Nuclear Information System (INIS)

Sovinec, Carl

2016-01-01

The study entitled, 'Transport and Dynamics in Toroidal Fusion Systems,' (TDTFS) applied analytical theory and numerical computation to investigate topics of importance to confining plasma, the fourth state of matter, with magnetic fields. A central focus of the work is how non-thermal components of the ion particle distribution affect the 'sawtooth' collective oscillation in the core of the tokamak magnetic configuration. Previous experimental and analytical research had shown and described how the oscillation frequency decreases and amplitude increases, leading to 'monster' or 'giant' sawteeth, when the non-thermal component is increased by injecting particle beams or by exciting ions with imposed electromagnetic waves. The TDTFS study applied numerical computation to self-consistently simulate the interaction between macroscopic collective plasma dynamics and the non-thermal particles. The modeling used the NIMROD code [Sovinec, Glasser, Gianakon, et al., J. Comput. Phys. 195, 355 (2004)] with the energetic component represented by simulation particles [Kim, Parker, Sovinec, and the NIMROD Team, Comput. Phys. Commun. 164, 448 (2004)]. The computations found decreasing growth rates for the instability that drives the oscillations, but they were ultimately limited from achieving experimentally relevant parameters due to computational practicalities. Nonetheless, this effort provided valuable lessons for integrated simulation of macroscopic plasma dynamics. It also motivated an investigation of the applicability of fluid-based modeling to the ion temperature gradient instability, leading to the journal publication [Schnack, Cheng, Barnes, and Parker, Phys. Plasmas 20, 062106 (2013)]. Apart from the tokamak-specific topics, the TDTFS study also addressed topics in the basic physics of magnetized plasma and in the dynamics of the reversed-field pinch (RFP) configuration. The basic physics work contributed to a study of two

Transport and Dynamics in Toroidal Fusion Systems

Energy Technology Data Exchange (ETDEWEB)

Sovinec, Carl [Univ. of Wisconsin, Madison, WI (United States)

2016-09-07

The study entitled, "Transport and Dynamics in Toroidal Fusion Systems," (TDTFS) applied analytical theory and numerical computation to investigate topics of importance to confining plasma, the fourth state of matter, with magnetic fields. A central focus of the work is how non-thermal components of the ion particle distribution affect the "sawtooth" collective oscillation in the core of the tokamak magnetic configuration. Previous experimental and analytical research had shown and described how the oscillation frequency decreases and amplitude increases, leading to "monster" or "giant" sawteeth, when the non-thermal component is increased by injecting particle beams or by exciting ions with imposed electromagnetic waves. The TDTFS study applied numerical computation to self-consistently simulate the interaction between macroscopic collective plasma dynamics and the non-thermal particles. The modeling used the NIMROD code [Sovinec, Glasser, Gianakon, et al., J. Comput. Phys. 195, 355 (2004)] with the energetic component represented by simulation particles [Kim, Parker, Sovinec, and the NIMROD Team, Comput. Phys. Commun. 164, 448 (2004)]. The computations found decreasing growth rates for the instability that drives the oscillations, but they were ultimately limited from achieving experimentally relevant parameters due to computational practicalities. Nonetheless, this effort provided valuable lessons for integrated simulation of macroscopic plasma dynamics. It also motivated an investigation of the applicability of fluid-based modeling to the ion temperature gradient instability, leading to the journal publication [Schnack, Cheng, Barnes, and Parker, Phys. Plasmas 20, 062106 (2013)]. Apart from the tokamak-specific topics, the TDTFS study also addressed topics in the basic physics of magnetized plasma and in the dynamics of the reversed-field pinch (RFP) configuration. The basic physics work contributed to a study of two-fluid effects on interchange dynamics, where

Control of Internal Transport Barriers in Magnetically Confined Fusion Plasmas

Science.gov (United States)

Panta, Soma; Newman, David; Sanchez, Raul; Terry, Paul

2016-10-01

In magnetic confinement fusion devices the best performance often involves some sort of transport barriers to reduce the energy and particle flow from core to edge. Those barriers create gradients in the temperature and density profiles. If gradients in the profiles are too steep that can lead to instabilities and the system collapses. Control of these barriers is therefore an important challenge for fusion devices (burning plasmas). In this work we focus on the dynamics of internal transport barriers. Using a simple 7 field transport model, extensively used for barrier dynamics and control studies, we explore the use of RF heating to control the local gradients and therefore the growth rates and shearing rates for barrier initiation and control in self-heated fusion plasmas. Ion channel barriers can be formed in self-heated plasmas with some NBI heating but electron channel barriers are very sensitive. They can be formed in self-heated plasmas with additional auxiliary heating i.e. NBI and radio-frequency(RF). Using RF heating on both electrons and ions at proper locations, electron channel barriers along with ion channel barriers can be formed and removed demonstrating a control technique. Investigating the role of pellet injection in controlling the barriers is our next goal. Work supported by DOE Grant DE-FG02-04ER54741.

Hemi-fused structure mediates and controls fusion and fission in live cells.

Science.gov (United States)

Zhao, Wei-Dong; Hamid, Edaeni; Shin, Wonchul; Wen, Peter J; Krystofiak, Evan S; Villarreal, Seth A; Chiang, Hsueh-Cheng; Kachar, Bechara; Wu, Ling-Gang

2016-06-23

Membrane fusion and fission are vital for eukaryotic life. For three decades, it has been proposed that fusion is mediated by fusion between the proximal leaflets of two bilayers (hemi-fusion) to produce a hemi-fused structure, followed by fusion between the distal leaflets, whereas fission is via hemi-fission, which also produces a hemi-fused structure, followed by full fission. This hypothesis remained unsupported owing to the lack of observation of hemi-fusion or hemi-fission in live cells. A competing fusion hypothesis involving protein-lined pore formation has also been proposed. Here we report the observation of a hemi-fused Ω-shaped structure in live neuroendocrine chromaffin cells and pancreatic β-cells, visualized using confocal and super-resolution stimulated emission depletion microscopy. This structure is generated from fusion pore opening or closure (fission) at the plasma membrane. Unexpectedly, the transition to full fusion or fission is determined by competition between fusion and calcium/dynamin-dependent fission mechanisms, and is notably slow (seconds to tens of seconds) in a substantial fraction of the events. These results provide key missing evidence in support of the hemi-fusion and hemi-fission hypothesis in live cells, and reveal the hemi-fused intermediate as a key structure controlling fusion and fission, as fusion and fission mechanisms compete to determine the transition to fusion or fission.

A scheme for reducing deceleration-phase Rayleigh-Taylor growth in inertial confinement fusion implosions

Science.gov (United States)

Wang, L. F.; Ye, W. H.; Wu, J. F.; Liu, Jie; Zhang, W. Y.; He, X. T.

2016-05-01

It is demonstrated that the growth of acceleration-phase instabilities in inertial confinement fusion implosions can be controlled, especially in the high-foot implosions [O. A. Hurricane et al., Phys. Plasmas 21, 056314 (2014)] on the National Ignition Facility. However, the excessive growth of the deceleration-phase instabilities can still destroy the hot spot ignition. A scheme is proposed to retard the deceleration-phase Rayleigh-Taylor instability growth by shock collision near the waist of the inner shell surface. Two-dimensional radiation hydrodynamic simulations confirm the improved deceleration-phase hot spot stability properties without sacrificing the fuel compression.

A scheme for reducing deceleration-phase Rayleigh–Taylor growth in inertial confinement fusion implosions

Energy Technology Data Exchange (ETDEWEB)

Wang, L. F., E-mail: wang-lifeng@iapcm.ac.cn; Ye, W. H.; Liu, Jie [Institute of Applied Physics and Computational Mathematics, Beijing 100094 (China); HEDPS, Center for Applied Physics and Technology, Peking University, Beijing 100871 (China); Center for Fusion Energy Science and Technology, Chinese Academy of Engineering Physics, Beijing 100088 (China); Wu, J. F. [Institute of Applied Physics and Computational Mathematics, Beijing 100094 (China); Center for Fusion Energy Science and Technology, Chinese Academy of Engineering Physics, Beijing 100088 (China); Zhang, W. Y. [Institute of Applied Physics and Computational Mathematics, Beijing 100094 (China); He, X. T. [Institute of Applied Physics and Computational Mathematics, Beijing 100094 (China); HEDPS, Center for Applied Physics and Technology, Peking University, Beijing 100871 (China)

2016-05-15

It is demonstrated that the growth of acceleration-phase instabilities in inertial confinement fusion implosions can be controlled, especially in the high-foot implosions [O. A. Hurricane et al., Phys. Plasmas 21, 056314 (2014)] on the National Ignition Facility. However, the excessive growth of the deceleration-phase instabilities can still destroy the hot spot ignition. A scheme is proposed to retard the deceleration-phase Rayleigh–Taylor instability growth by shock collision near the waist of the inner shell surface. Two-dimensional radiation hydrodynamic simulations confirm the improved deceleration-phase hot spot stability properties without sacrificing the fuel compression.

Status report on controlled thermonuclear fusion

International Nuclear Information System (INIS)

1990-01-01

The International Fusion Research Council has prepared this report on the current status of fusion, an update of its 1978 report, at the request of the Director General of the International Atomic Energy Agency. The report consists of an introductory note by the Director General, an Executive Summary and General Overview published in this document, and a series of technical reports. The background of fusion as an energy source is documented and compared with fission. The two approaches to thermonuclear fusion, magnetic confinement and inertial confinement, are discussed. The viability with respect to economic, environmental, and safety aspects is discussed. Fusion programs in the European Community, Japan, the USSR, the USA, as well as smaller programs in other countries are described. The status of fusion physics and technology is elucidated, and future directions and plans are indicated. 5 refs, 6 figs

Controlled Fusion with Hot-ion Mode in a Degenerate Plasma

International Nuclear Information System (INIS)

S. Son and N.J. Fisch

2005-01-01

In a Fermi-degenerate plasma, the rate of electron physical processes is much reduced from the classical prediction, possibly enabling new regimes for controlled nuclear fusion, including the hot-ion mode, a regime in which the ion temperature exceeds the electron temperature. Previous calculations of these processes in dense plasmas are now corrected for partial degeneracy and relativistic effects, leading to an expanded regime of self-sustained fusion

Fusion Physics

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, Mitsuru; Lackner, Karl; Tran, Minh Quang [eds.

2012-09-15

Recreating the energy production process of the Sun - nuclear fusion - on Earth in a controlled fashion is one of the greatest challenges of this century. If achieved at affordable costs, energy supply security would be greatly enhanced and environmental degradation from fossil fuels greatly diminished. Fusion Physics describes the last fifty years or so of physics and research in innovative technologies to achieve controlled thermonuclear fusion for energy production. The International Atomic Energy Agency (IAEA) has been involved since its establishment in 1957 in fusion research. It has been the driving force behind the biennial conferences on Plasma Physics and Controlled Thermonuclear Fusion, today known as the Fusion Energy Conference. Hosted by several Member States, this biennial conference provides a global forum for exchange of the latest achievements in fusion research against the backdrop of the requirements for a net energy producing fusion device and, eventually, a fusion power plant. The scientific and technological knowledge compiled during this series of conferences, as well as by the IAEA Nuclear Fusion journal, is immense and will surely continue to grow in the future. It has led to the establishment of the International Thermonuclear Experimental Reactor (ITER), which represents the biggest experiment in energy production ever envisaged by humankind.

Simultaneous qubit-loss-free fusion of three multiple W states

Science.gov (United States)

Wang, Meiyu; Hao, Quanzhi; Yan, Fengli; Gao, Ting

2018-05-01

Qubit-loss-free fusion for two W states introduced by Li K et al (2016 Phys. Rev. A 94 062315) clearly increases the final size of the obtained W state and greatly reduces the number of fusion steps to achieve a W state of a target size. Motivated by this idea, we propose a qubit-loss-free fusion scheme for fusing three polarization entangled W states simultaneously. The elements of a two-outcome positive-operator valued measurement and the appropriate joint unitary operation for realizing a positive-operator valued measurement measurement are given. As an example, with the assistance of weak cross-Kerr nonlinearities, an optical setup for fusing three W states is proposed. We analyze the success probability of the scheme and the resource cost of the present scheme, as compared to previous work.

Theoretical model of the probability of fusion between deuterons within deformed lattices with microcracks at room temperature

International Nuclear Information System (INIS)

Frisone, Fulvio

2006-01-01

In this work we wish to demonstrate that a reaction path as the following dislocations, deformations due to thermodynamic stress and, finally, microcrack occurrence, can enhance the process of fusion of the deuterons introduced into the lattice by deuterium loading (F. Frisone, Can variations in temperature influence deuteron interaction within crystalline lattices?, Nuovo Cimento D, 18, 1279 (1996)). In fact, calculating the rate of deuteron-plasmon-deuteron fusion within a microcrack, showed, together with an enhancement of the tunneling effect, an increase of at least 2 - 3 orders of magnitude compared to the probability of fusion on the no deformed lattice. In fact, strong electric fields can take place in the microcrack and the deuterons are accelerated to the energy which is enough for the D-D tunnelling (M. Rabinowitz, High temperature superconductivity and cold fusion, Mod. Phys, Lett. B, 4, 233 (1990); J. Price Hirt and J. Lothe, Theory of Dislocation (McGraw Hill); Z. Phys., 457, 156 (1960)). These phenomena open the way to the theoretical hypothesis that a kind of chain reaction, catalyzed by the microcracks produced in the structure as a result of deuterium loading, can favour tho process of deuteron-plasmon fusion (N. W. Ashcroft and N. D. Mermin (Eds.), Solid State Physics, Chapter 25 (Saunders College, Philadelphia, 1972, pp. 492-509)

Saturation of alpha particle driven instability in Tokamak Fusion Test Reactor

International Nuclear Information System (INIS)

Gorelenkov, N.N.; Chen, Y.; White, R.B.; Berk, H.L.

1999-01-01

A nonlinear theory of kinetic instabilities near threshold [Berk et al., Plasma Phys. Rep. 23, 842 (1997)] is applied to calculate the saturation level of toroidicity-induced Alfven eigenmodes (TAE), and to be compared with the predictions of δf method calculations (Y. Chen, Ph.D. thesis, Princeton University, 1998). Good agreement is observed between the predictions of both methods and the predicted saturation levels are comparable to experimentally measured amplitudes of the TAE oscillations in Tokamak Fusion Test Reactor [D. J. Grove and D. M. Meade, Nucl. Fusion 25, 1167 (1985)]. copyright 1999 American Institute of Physics

Brazilian programme for plasma physics and controlled thermonuclear fusion

International Nuclear Information System (INIS)

Chian, A.C.L.; Reusch, M.F.; Nascimento, I.C.; Pantuso-Sudano, J.

1992-01-01

A proposal for a National Programme of Plasma Physics and Controlled Thermonuclear Fusion in Brazil is presented, aimimg the dissemination of the researchers thought in plasma physics for the national authorities and the scientific community. (E.O.)

NATO Advanced Study Institute entitled Physics of Plasma-Wall Interactions in Controlled Fusion

CERN Document Server

Behrisch, R; Physics of plasma-wall interactions in controlled fusion

1986-01-01

Controlled thermonuclear fusion is one of the possible candidates for long term energy sources which will be indispensable for our highly technological society. However, the physics and technology of controlled fusion are extremely complex and still require a great deal of research and development before fusion can be a practical energy source. For producing energy via controlled fusion a deuterium-tritium gas has to be heated to temperatures of a few 100 Million °c corres­ ponding to about 10 keV. For net energy gain, this hot plasma has to be confined at a certain density for a certain time One pro­ mising scheme to confine such a plasma is the use of i~tense mag­ netic fields. However, the plasma diffuses out of the confining magnetic surfaces and impinges on the surrounding vessel walls which isolate the plasma from the surrounding air. Because of this plasma wall interaction, particles from the plasma are lost to the walls by implantation and are partially reemitted into the plasma. In addition, wall...

Italy, EURATOM and Early Research on Controlled Thermonuclear Fusion (1957-1962)

International Nuclear Information System (INIS)

Curli, Barbara

2017-01-01

This chapter traces the early origins of European collaboration in controlled thermonuclear fusion research, within the larger picture of Cold War nuclear policy in the late 1950s-early 1960s, and as a consequence of the signing of the EURATOM treaty in 1957. It then presents some preliminary findings on the Association contract which was signed in 1960 between EURATOM and Italy, in order to carry out research in controlled thermonuclear fusion at the then newly created 'Laboratori nazionali di Frascati', near Rome, within the framework of the Comitato Nazionale Energia Nucleare (CNEN), the Italian civilian nuclear energy agency.

Minimizing scatter-losses during pre-heat for magneto-inertial fusion targets

Science.gov (United States)

Geissel, Matthias; Harvey-Thompson, Adam J.; Awe, Thomas J.; Bliss, David E.; Glinsky, Michael E.; Gomez, Matthew R.; Harding, Eric; Hansen, Stephanie B.; Jennings, Christopher; Kimmel, Mark W.; Knapp, Patrick; Lewis, Sean M.; Peterson, Kyle; Schollmeier, Marius; Schwarz, Jens; Shores, Jonathon E.; Slutz, Stephen A.; Sinars, Daniel B.; Smith, Ian C.; Speas, C. Shane; Vesey, Roger A.; Weis, Matthew R.; Porter, John L.

2018-02-01

The size, temporal and spatial shape, and energy content of a laser pulse for the pre-heat phase of magneto-inertial fusion affect the ability to penetrate the window of the laser-entrance-hole and to heat the fuel behind it. High laser intensities and dense targets are subject to laser-plasma-instabilities (LPI), which can lead to an effective loss of pre-heat energy or to pronounced heating of areas that should stay unexposed. While this problem has been the subject of many studies over the last decades, the investigated parameters were typically geared towards traditional laser driven Inertial Confinement Fusion (ICF) with densities either at 10% and above or at 1% and below the laser's critical density, electron temperatures of 3-5 keV, and laser powers near (or in excess of) 1 × 1015 W/cm2. In contrast, Magnetized Liner Inertial Fusion (MagLIF) [Slutz et al., Phys. Plasmas 17, 056303 (2010) and Slutz and Vesey, Phys. Rev. Lett. 108, 025003 (2012)] currently operates at 5% of the laser's critical density using much thicker windows (1.5-3.5 μm) than the sub-micron thick windows of traditional ICF hohlraum targets. This article describes the Pecos target area at Sandia National Laboratories using the Z-Beamlet Laser Facility [Rambo et al., Appl. Opt. 44(12), 2421 (2005)] as a platform to study laser induced pre-heat for magneto-inertial fusion targets, and the related progress for Sandia's MagLIF program. Forward and backward scattered light were measured and minimized at larger spatial scales with lower densities, temperatures, and powers compared to LPI studies available in literature.

Demonstration of thermonuclear conditions in magnetized liner inertial fusion experiments

International Nuclear Information System (INIS)

Gomez, M. R.; Slutz, S. A.; Sefkow, A. B.; Hahn, K. D.; Hansen, S. B.; Knapp, P. F.; Schmit, P. F.; Ruiz, C. L.; Sinars, D. B.; Harding, E. C.; Jennings, C. A.; Awe, T. J.; Geissel, M.; Rovang, D. C.; Smith, I. C.; Chandler, G. A.; Cooper, G. W.; Cuneo, M. E.; Harvey-Thompson, A. J.; Hess, M. H.

2015-01-01

The magnetized liner inertial fusion concept [S. A. Slutz et al., Phys. Plasmas 17, 056303 (2010)] utilizes a magnetic field and laser heating to relax the pressure requirements of inertial confinement fusion. The first experiments to test the concept [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)] were conducted utilizing the 19 MA, 100 ns Z machine, the 2.5 kJ, 1 TW Z Beamlet laser, and the 10 T Applied B-field on Z system. Despite an estimated implosion velocity of only 70 km/s in these experiments, electron and ion temperatures at stagnation were as high as 3 keV, and thermonuclear deuterium-deuterium neutron yields up to 2 × 10 12 have been produced. X-ray emission from the fuel at stagnation had widths ranging from 50 to 110 μm over a roughly 80% of the axial extent of the target (6–8 mm) and lasted approximately 2 ns. X-ray yields from these experiments are consistent with a stagnation density of the hot fuel equal to 0.2–0.4 g/cm 3 . In these experiments, up to 5 × 10 10 secondary deuterium-tritium neutrons were produced. Given that the areal density of the plasma was approximately 1–2 mg/cm 2 , this indicates the stagnation plasma was significantly magnetized, which is consistent with the anisotropy observed in the deuterium-tritium neutron spectra. Control experiments where the laser and/or magnetic field were not utilized failed to produce stagnation temperatures greater than 1 keV and primary deuterium-deuterium yields greater than 10 10 . An additional control experiment where the fuel contained a sufficient dopant fraction to substantially increase radiative losses also failed to produce a relevant stagnation temperature. The results of these experiments are consistent with a thermonuclear neutron source

Improved Controls for Fusion RF Systems. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Casey, Jeffrey A. [Rockfield Research Inc., Las Vegas, NV (United States)

2011-11-08

We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way that they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration.

Improved Controls for Fusion RF Systems. Final technical report

International Nuclear Information System (INIS)

Casey, Jeffrey A.

2011-01-01

We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way that they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration

Controlled thermonuclear fusion: research on magnetic fusion

International Nuclear Information System (INIS)

Paris, P.J.

1988-12-01

Recent progress in thermonuclear fusion research indicates that the scientists' schedule for the demonstration of the scientific feasibility will be kept and that break-even will be attained in the course of the next decade. To see the implementation of ignition, however, the generation of future experiments must be awaited. These projects are currently under study. With technological research going on in parallel, they should at the same time contribute to the design of a reactor. Fusion reactors will be quite different from the fission nuclear reactors we know, and the waste of the plants will also be of a different nature. It is still too early to define the precise design of a fusion reactor. On the basis of a toric machine concept like that of the tokamak, we can, however, envisage that the problems with which we are confronted will be solved one after the other. As we have just seen, these will be the objectives of the future experimental installations where ignition will be possible and where the flux of fast neutrons will be so strong that they will allow the study of low-activation materials which will be used in the structure of the reactor. But this is also a task in which from now onwards numerous laboratories in Europe and in the world participate. The works are in fact punctiform, and often the mutual incidences can only be determined by an approach simulated by numerical codes. (author) 19 figs., 6 tabs., 8 refs

Dynamic symmetry of indirectly driven inertial confinement fusion capsules on the National Ignition Facility

International Nuclear Information System (INIS)

Town, R. P. J.; Bradley, D. K.; Kritcher, A.; Jones, O. S.; Rygg, J. R.; Tommasini, R.; Barrios, M.; Benedetti, L. R.; Berzak Hopkins, L. F.; Celliers, P. M.; Döppner, T.; Dewald, E. L.; Eder, D. C.; Field, J. E.; Glenn, S. M.; Izumi, N.; Haan, S. W.; Khan, S. F.; Ma, T.; Milovich, J. L.

2014-01-01

In order to achieve ignition using inertial confinement fusion it is important to control the growth of low-mode asymmetries as the capsule is compressed. Understanding the time-dependent evolution of the shape of the hot spot and surrounding fuel layer is crucial to optimizing implosion performance. A design and experimental campaign to examine sources of asymmetry and to quantify symmetry throughout the implosion has been developed and executed on the National Ignition Facility (NIF) [E. I. Moses et al., Phys. Plasmas 16, 041006 (2009)]. We have constructed a large simulation database of asymmetries applied during different time intervals. Analysis of the database has shown the need to measure and control the hot-spot shape, areal density distribution, and symmetry swings during the implosion. The shape of the hot spot during final stagnation is measured using time-resolved imaging of the self-emission, and information on the shape of the fuel at stagnation can be obtained from Compton radiography [R. Tommasini et al., Phys. Plasmas 18, 056309 (2011)]. For the first time on NIF, two-dimensional inflight radiographs of gas-filled and cryogenic fuel layered capsules have been measured to infer the symmetry of the radiation drive on the capsule. These results have been used to modify the hohlraum geometry and the wavelength tuning to improve the inflight implosion symmetry. We have also expanded our shock timing capabilities by the addition of extra mirrors inside the re-entrant cone to allow the simultaneous measurement of shock symmetry in three locations on a single shot, providing asymmetry information up to Legendre mode 4. By diagnosing the shape at nearly every step of the implosion, we estimate that shape has typically reduced fusion yield by about 50% in ignition experiments

Exploring Physics with Computer Animation and PhysGL

Science.gov (United States)

Bensky, T. J.

2016-10-01

This book shows how the web-based PhysGL programming environment (http://physgl.org) can be used to teach and learn elementary mechanics (physics) using simple coding exercises. The book's theme is that the lessons encountered in such a course can be used to generate physics-based animations, providing students with compelling and self-made visuals to aid their learning. Topics presented are parallel to those found in a traditional physics text, making for straightforward integration into a typical lecture-based physics course. Users will appreciate the ease at which compelling OpenGL-based graphics and animations can be produced using PhysGL, as well as its clean, simple language constructs. The author argues that coding should be a standard part of lower-division STEM courses, and provides many anecdotal experiences and observations, that include observed benefits of the coding work.

Development and characterization of a Z-pinch-driven hohlraum high-yield inertial confinement fusion target concept

International Nuclear Information System (INIS)

Cuneo, Michael E.; Vesey, Roger A.; Porter, John L. Jr.; Chandler, Gordon A.; Fehl, David L.; Gilliland, Terrance L.; Hanson, David L.; McGurn, John S.; Reynolds, Paul G.; Ruggles, Laurence E.; Seamen, Hans; Spielman, Rick B.; Struve, Ken W.; Stygar, William A.; Simpson, Walter W.; Torres, Jose A.; Wenger, David F.; Hammer, James H.; Rambo, Peter W.; Peterson, Darrell L.

2001-01-01

Initial experiments to study the Z-pinch-driven hohlraum high-yield inertial confinement fusion (ICF) concept of Hammer, Tabak, and Porter [Hammer et al., Phys. Plasmas 6, 2129 (1999)] are described. The relationship between measured pinch power, hohlraum temperature, and secondary hohlraum coupling ('hohlraum energetics') is well understood from zero-dimensional semianalytic, and two-dimensional view factor and radiation magnetohydrodynamics models. These experiments have shown the highest x-ray powers coupled to any Z-pinch-driven secondary hohlraum (26±5 TW), indicating the concept could scale to fusion yields of >200 MJ. A novel, single-sided power feed, double-pinch driven secondary that meets the pinch simultaneity requirements for polar radiation symmetry has also been developed. This source will permit investigation of the pinch power balance and hohlraum geometry requirements for ICF relevant secondary radiation symmetry, leading to a capsule implosion capability on the Z accelerator [Spielman et al., Phys. Plasmas 5, 2105 (1998)

Twentyseventh European physical society conference on controlled fusion and plasma physics

International Nuclear Information System (INIS)

Igitkhanov, Y.

2000-01-01

The twentyseventh European physical society conference on controlled fusion and plasma physics was held in Budapest, 12-16 June 2000. About 10 invited papers were presented, covering a wide range of problems in plasma physics, including confinement and transport issues in fusion devices, astrophysics and industrial application of plasmas. More than 100 papers were presented on plasma theory and experiments from tokamaks and stellarators. Some of the ITER-relevant issues covered are described in this newsletter

Line-Tension Controlled Mechanism for Influenza Fusion

NARCIS (Netherlands)

Risselada, Herre Jelger; Marelli, Giovanni; Fuhrmans, Marc; Smirnova, Yuliya G.; Grubmueller, Helmut; Marrink, Siewert Jan; Mueller, Marcus

2012-01-01

Our molecular simulations reveal that wild-type influenza fusion peptides are able to stabilize a highly fusogenic pre-fusion structure, i.e. a peptide bundle formed by four or more trans-membrane arranged fusion peptides. We rationalize that the lipid rim around such bundle has a non-vanishing rim

Implications of the second law for future directions in controlled fusion research

International Nuclear Information System (INIS)

Roth, J.R.; Miley, G.H.

1980-01-01

Many existing energy related technologies have developed under the influence of social, economic, or state of the art constraints, and they cannot be viewed as optimum systems according to the second law of thermodynamics. Controlled fusion research presents an opportunity to optimize a nascent technology with respect to second law considerations in order to develop a practical energy source. In its present state of development, fusion research offers several independent approaches that may result in a net power producing fusion reactor. This paper discusses how second law considerations might be used to narrow the range of choices that must be made among various fusion fuel cycles. From a second law point of view, the most desirable fusion reactors are those for which the energy of charged particles can be converted directly into d.c. electrical power, while still allowing the energy that could be recovered by an efficient high-temperature 'blanket' to be transported largely by radiation. Fusion research in all major industrialized countries is developing the deuterium-tritium (D-T) fuel cycle for first-generation fusion power plants. It will be shown that other fuel cycles have significant advantages over the D-T fuel cycle according to second law principles. (author)

The effect of controlled shot peening on fusion welded joints

International Nuclear Information System (INIS)

Lah, Nur Azida Che; Ali, Aidy; Ismail, Napsiah; Chai, Lim Poon; Mohamed, Abdul Aziz

2010-01-01

This work examines the effect of controlled shot peening (CSP) treatment on the fatigue strength of an ASTM A516 grade 70 carbon steel welded joint. Metallurgical modifications, hardness, elemental compositions, and internal discontinuities, such as porosity, inclusions, lack of penetration, and undercut found in treated and untreated fusion welded joints, were characterized. The fatigue results of as-welded and peened skimmed joints were compared. It was observed that the effect of the CSP and skimming processes improved the fatigue life of the fusion weld by 50% on MMA-welded, 63% on MIG-welded, and 60% on TIG-welded samples.

Advanced real-time control systems for magnetically confined fusion plasmas

International Nuclear Information System (INIS)

Goncalves, B.; Sousa, J.; Fernandes, H.; Rodrigues, A.P.; Carvalho, B.B.; Neto, A.; Varandas, C.A.F.

2008-01-01

Real-time control of magnetically confined plasmas is a critical issue for the safety, operation and high performance scientific exploitation of the experimental devices on regimes beyond the current operation frontiers. The number of parameters and the data volumes used for the plasma properties identification scale normally not only with the machine size but also with the technology improvements, leading to a great complexity of the plant system. A strong computational power and fast communication infrastructure are needed to handle in real-time this information, allowing just-in-time decisions to achieve the fusion critical plasma conditions. These advanced control systems require a tiered infrastructure including the hardware layer, the signal-processing middleware, real-time timing and data transport, the real-time operating system tools and drivers, the framework for code development, simulation, deployment and experiment parameterization and the human real-time plasma condition monitoring and management. This approach is being implemented at CFN by offering a vertical solution for the forthcoming challenges, including ITER, the first experimental fusion reactor. A given set of tools and systems are described on this paper, namely: (i) an ATCA based hardware multiple-input-multiple-output (MIMO) platform, PCI and PCIe acquisition and control modules; (ii) FPGA and DSP parallelized signal processing algorithms; (iii) a signal data and event distribution system over a 2.5/10Gb optical network with sub-microsecond latencies; (iv) RTAI and Linux drivers; and (v) the FireSignal, FusionTalk, SDAS FireCalc application tools. (author)

Burn Control in Fusion Reactors via Nonlinear Stabilization Techniques

International Nuclear Information System (INIS)

Schuster, Eugenio; Krstic, Miroslav; Tynan, George

2003-01-01

Control of plasma density and temperature magnitudes, as well as their profiles, are among the most fundamental problems in fusion reactors. Existing efforts on model-based control use control techniques for linear models. In this work, a zero-dimensional nonlinear model involving approximate conservation equations for the energy and the densities of the species was used to synthesize a nonlinear feedback controller for stabilizing the burn condition of a fusion reactor. The subignition case, where the modulation of auxiliary power and fueling rate are considered as control forces, and the ignition case, where the controlled injection of impurities is considered as an additional actuator, are treated separately.The model addresses the issue of the lag due to the finite time for the fresh fuel to diffuse into the plasma center. In this way we make our control system independent of the fueling system and the reactor can be fed either by pellet injection or by puffing. This imposed lag is treated using nonlinear backstepping.The nonlinear controller proposed guarantees a much larger region of attraction than the previous linear controllers. In addition, it is capable of rejecting perturbations in initial conditions leading to both thermal excursion and quenching, and its effectiveness does not depend on whether the operating point is an ignition or a subignition point.The controller designed ensures setpoint regulation for the energy and plasma parameter β with robustness against uncertainties in the confinement times for different species. Hence, the controller can increase or decrease β, modify the power, the temperature or the density, and go from a subignition to an ignition point and vice versa

Status report on controlled thermonuclear fusion

International Nuclear Information System (INIS)

1990-06-01

The International Fusion Research Council (IFRC), an advisory body to the International Atomic Energy Agency, reports on the current status of fusion; this report updates its 1978 status report. This report contains a General Overview and Executive Summary, and reports on all current approaches to fusion throughout the world; a series of technical reports is to be published elsewhere. This report is timely in that it not only shows progress which has occurred over the past, but interfaces with possible future devices, in particular the International Thermonuclear Experimental Reactor (ITER), whose conceptual design phase is nearing completion. 5 refs, 6 figs

rhBMP-2 for posterolateral instrumented lumbar fusion: a multicenter prospective randomized controlled trial.

Science.gov (United States)

Hurlbert, R John; Alexander, David; Bailey, Stewart; Mahood, James; Abraham, Ed; McBroom, Robert; Jodoin, Alain; Fisher, Charles

2013-12-01

Multicenter randomized controlled trial. To evaluate the effect of recombinant human bone morphogenetic protein (rhBMP-2) on radiographical fusion rate and clinical outcome for surgical lumbar arthrodesis compared with iliac crest autograft. In many types of spinal surgery, radiographical fusion is a primary outcome equally important to clinical improvement, ensuring long-term stability and axial support. Biologic induction of bone growth has become a commonly used adjunct in obtaining this objective. We undertook this study to objectify the efficacy of rhBMP-2 compared with traditional iliac crest autograft in instrumented posterolateral lumbar fusion. Patients undergoing 1- or 2-level instrumented posterolateral lumbar fusion were randomized to receive either autograft or rhBMP-2 for their fusion construct. Clinical and radiographical outcome measures were followed for 2 to 4 years postoperatively. One hundred ninety seven patients were successfully randomized among the 8 participating institutions. Adverse events attributable to the study drug were not significantly different compared with controls. However, the control group experienced significantly more graft-site complications as might be expected. 36-Item Short Form Health Survey, Oswestry Disability Index, and leg/back pain scores were comparable between the 2 groups. After 4 years of follow-up, radiographical fusion rates remained significantly higher in patients treated with rhBMP-2 (94%) than those who received autograft (69%) (P = 0.007). The use of rhBMP-2 for instrumented posterolateral lumbar surgery significantly improves the chances of radiographical fusion compared with the use of autograft. However, there is no associated improvement in clinical outcome within a 4-year follow-up period. These results suggest that use of rhBMP-2 should be considered in cases where lumbar arthrodesis is of primary concern.

Energy balance of controlled thermonuclear fusion

International Nuclear Information System (INIS)

Hashmi, M.; Staudenmaier, G.

2000-01-01

It is shown that a discrepancy and incompatibility persist between basic physics and fusion-literature regarding the radiation losses from a thermonuclear plasma. Whereas the fusion-literature neglects the excitation or line radiation completely, according to basic physics it depends upon the prevailing conditions and cannot be neglected in general. Moreover, for a magnetized plasma, while the fusion-literature assumes a self-absorption or reabsorption of cyclotron or synchrotron radiation emitted by the electrons spiraling along the magnetic field, the basic physics does not allow any effective reabsorption of cyclotron or synchrotron radiation. As is demonstrated, fallacious assumptions and notions, which somehow or other crept into the fusion-literature, are responsible for this discrepancy. In the present work, the theory is corrected. On the grounds of basic physics, a complete energy balance of magnetized and non-magnetized plasmas is presented for pulsed, stationary and self-sustaining operations by taking into account the energy release by reactions of light nuclei as well as different kinds of diffusive (conduction) and radiative (bremsstrahlung, cyclotron or synchrotron radiation and excitation radiation) energy losses. Already the energy losses by radiation make the energy balance negative. Hence, a fusion reactor-an energy producing device-seems to be beyond the realms of realization. (orig.)

Plasma physics for controlled fusion

CERN Document Server

Miyamoto, Kenro

2016-01-01

This new edition presents the essential theoretical and analytical methods needed to understand the recent fusion research of tokamak and alternate approaches. The author describes magnetohydrodynamic and kinetic theories of cold and hot plasmas in detail. The book covers new important topics for fusion studies such as plasma transport by drift turbulence, which depend on the magnetic configuration and zonal flows. These are universal phenomena of microturbulence. They can modify the onset criterion for turbulent transport, instabilities driven by energetic particles as well as alpha particle generation and typical plasma models for computer simulation. The fusion research of tokamaks with various new versions of H modes are explained. The design concept of ITER, the international tokamak experimental reactor, is described for inductively driven operations as well as steady-state operations using non-inductive drives. Alternative approaches of reversed-field pinch and its relaxation process, stellator includi...

Operating large controlled thermonuclear fusion research facilities

International Nuclear Information System (INIS)

Gaudreau, M.P.J.; Tarrh, J.M.; Post, R.S.; Thomas, P.

1987-01-01

The MIT Tara Tandem Mirror is a large, state of the art controlled thermonuclear fusion research facility. Over the six years of its design, implementation, and operation, every effort was made to minimize cost and maximize performance by using the best and latest hardware, software, and scientific and operational techniques. After reviewing all major DOE fusion facilities, an independent DOE review committee concluded that the Tara operation was the most automated and efficient of all DOE facilities. This paper includes a review of the key elements of the Tara design, construction, operation, management, physics milestones, and funding that led to this success. The authors emphasize a chronological description of how the system evolved from the proposal stage to a mature device with an emphasis on the basic philosophies behind the implementation process. This description can serve both as a qualitative and quantitative database for future large experiment planning. It includes actual final costs and manpower spent as well as actual run and maintenance schedules, number of data shots, major system failures, etc. The paper concludes with recommendations for the next generation of facilities

Base isolation technique for tokamak type fusion reactor using adaptive control

International Nuclear Information System (INIS)

Koizumi, T.; Tsujiuchi, N.; Kishimoto, F.; Iida, H.; Fujita, T.

1991-01-01

In this paper relating to the isolation device of heavy structure such as nuclear fusion reactor, a control rule for reducing the response acceleration and relative displacement simultaneously was formulated, and the aseismic performance was improved by employing the adaptive control method of changing the damping factors of the system adaptively every moment. The control rule was studied by computer simulation, and the aseismic effect was evaluated in an experiment employing a scale model. As a results, the following conclusions were obtained. (1) By employing the control rule presented in this paper, both absolute acceleration and relative displacement can be reduced simultaneously without making the system unstable. (2) By introducing this control rule in a scale model assuming the Tokamak type fusion reactor, the response acceleration can be suppressed down to 78 % and also the relative displacement to 79 % as compared with the conventional aseismic method. (3) The sensitivities of absolute acceleration and relative displacement with respect to the control gain are not equal. However, by employing the relative weighting factor between the absolute acceleration and relative displacement, it is possible to increase the control capability for any kind of objective structures and appliances. (author)

Controlled thermonuclear fusion

International Nuclear Information System (INIS)

Rebut, P.H.

1992-01-01

The author gives a chronological account of the research about thermonuclear fusion and presents the principle of JET thermonuclear reactor based upon the magnetic confinement. The problems of heating and confining a thermonuclear plasma may be regarded as solved. They make possible the definition of the size and geometry needed to realize a next-step tokamak (ITER, NET projects)

Tertiary proton diagnostics in future inertial confinement fusion experiments

International Nuclear Information System (INIS)

Cremer, S.; Verdon, C.P.; Petrasso, R.D.

1998-01-01

Recently, it was proposed to use energetic (up to 31 MeV) tertiary protons produced during the final stage of inertial confinement fusion implosions to measure the fuel areal density of compressed deuterium endash tritium (DT). The method is based on seeding the fuel with 3 He. The reaction of 3 He ions with the energetic knock-on deuterons, produced via the elastic scattering of 14.1 MeV neutrons, is a source of very energetic protons capable of escaping from very large areal density targets. This work presents results of detailed time-dependent Monte Carlo simulations of the nuclear processes involved in producing and transporting these protons through imploding targets proposed for direct-drive experiments on OMEGA [D. K. Bradley et al., Phys. Plasmas 5, 1870 (1998)] and the National Ignition Facility [S. W. Haan et al., Phys. Plasmas 2, 2480 (1995)]. copyright 1998 American Institute of Physics

Risk assessment of computer-controlled safety systems for fusion reactors

International Nuclear Information System (INIS)

Fryer, M.O.; Bruske, S.Z.

1983-01-01

The complexity of fusion reactor systems and the need to display, analyze, and react promptly to large amounts of information during reactor operation will require a number of safety systems in the fusion facilities to be computer controlled. Computer software, therefore, must be included in the reactor safety analyses. Unfortunately, the science of integrating computer software into safety analyses is in its infancy. Combined plant hardware and computer software systems are often treated by making simple assumptions about software performance. This method is not acceptable for assessing risks in the complex fusion systems, and a new technique for risk assessment of combined plant hardware and computer software systems has been developed. This technique is an extension of the traditional fault tree analysis and uses structured flow charts of the software in a manner analogous to wiring or piping diagrams of hardware. The software logic determines the form of much of the fault trees

Circumferential fusion is dominant over posterolateral fusion in a long-term perspective: cost-utility evaluation of a randomized controlled trial in severe, chronic low back pain

DEFF Research Database (Denmark)

Soegaard, Rikke; Bünger, Cody E; Christiansen, Terkel

2007-01-01

STUDY DESIGN: Cost-utility evaluation of a randomized, controlled trial with a 4- to 8-year follow-up. OBJECTIVE: To investigate the incremental cost per quality-adjusted-life-year (QALY) when comparing circumferential fusion to posterolateral fusion in a long-term, societal perspective. SUMMARY...... OF BACKGROUND DATA: The cost-effectiveness of circumferential fusion in a long-term perspective is uncertain but nonetheless highly relevant as the ISSLS prize winner 2006 in clinical studies reported the effect of circumferential fusion superior to the effect of posterolateral fusion. A recent trial found...... no significant difference between posterolateral and circumferential fusion reporting cost-effectiveness from a 2-year viewpoint. METHODS: A total of 146 patients were randomized to posterolateral or circumferential fusion and followed 4 to 8 years after surgery. The mean age of the cohort was 46 years (range...

Simulation and design of feedback control on resistive wall modes in Keda Torus eXperiment

International Nuclear Information System (INIS)

Li, Chenguang; Liu, Wandong; Li, Hong

2014-01-01

The feedback control of resistive wall modes (RWMs) in Keda Torus eXperiment (KTX) (Liu et al., Plasma Phys. Controlled Fusion 56, 094009 (2014)) is investigated by simulation. A linear model is built to describe the growth of the unstable modes in the absence of feedback and the resulting mode suppression due to feedback, given the typical reversed field pinch plasma equilibrium. The layout of KTX with two shell structures (the vacuum vessel and the stabilizing shell) is taken into account. The feedback performance is explored both in the scheme of “clean mode control” (Zanca et al., Nucl. Fusion 47, 1425 (2007)) and “raw mode control.” The discrete time control model with specific characteristic times will mimic the real feedback control action and lead to the favored control cycle. Moreover, the conceptual design of feedback control system is also presented, targeting on both RWMs and tearing modes

The fusion-fission hybrid

International Nuclear Information System (INIS)

Teller, E.

1985-01-01

As the history of the development of fusion energy shows, a sustained controlled fusion reaction is much more difficult to produce than rapid uncontrolled release of fusion energy. Currently, the ''magnetic bottle'' technique shows sufficient progress that it might applied for the commercial fuel production of /sup 233/U, suitable for use in fission reactors, by developing a fusion-fission hybrid. Such a device would consist of a fusion chamber core surrounded by a region containing cladded uranium pellets cooled by helium, with lithium salts also present to produce tritium to refuel the fusion process. Successful development of this hybrid might be possible within 10 y, and would provide both experience and funds for further development of controlled fusion energy

Plasma Surface interaction in Controlled fusion devices

International Nuclear Information System (INIS)

1990-05-01

The subjects presented in the 9th conference on plasma surface interaction in controlled fusion devices were: the modifications of power scrape-off-length and power deposition during various configurations in Tore Supra plasmas; the effects observed in ergodic divertor experiments in Tore-Supra; the diffuse connexion induced by the ergodic divertor and the topology of the heat load patterns on the plasma facing components in Tore-Supra; the study of the influence of air exposure on graphite implanted by low energy high density deuterium plasma

Toroidal electron beam energy storage for controlled fusion

International Nuclear Information System (INIS)

Clark, W.; Korn, P.; Mondelli, A.; Rostoker, N.

1976-01-01

In the presence of an external magnetic field stable equilibria exist for an unneutralized electron beam with ν/γ >1. As a result, it is in principle, possible to store very large quantities of energy in relatively small volumes by confining an unneutralized electron beam in a Tokamak-like device. The energy is stored principally in the electrostatic and self-magnetic fields associated with the beam and is available for rapid heating of pellets for controlled fusion. The large electrostatic potential well in such a device would be sufficient to contain energetic alpha particles, thereby reducing reactor wall bombardment. This approach also avoids plasma loss and wall bombardment by charge exchange neutrals. The conceptual design of an electrostatic Tokamak fusion reactor (ETFR) is discussed. A small toroidal device (the STP machine) has been constructed to test the principles involved. Preliminary experiments on this device have produced electron densities approximately 10% of those required in a reactor

Research program. Controlled thermonuclear fusion. Synthesis report 2014

International Nuclear Information System (INIS)

Villard, L.; Marot, L.; Fiocco, D.

2015-01-01

In 1961, 3 years after the 2 nd International Conference on Peaceful Use of Nuclear Energy, the Research Centre on Plasma Physics (CRPP) was created as a department of the Federal Institute of Technology (EPFL) in Lausanne (Switzerland). From 1979, CRPP collaborates to the European Program on fusion research in the framework of EURATOM. The advantages of fusion are remarkable: the fuel is available in great quantity all over the world; the reactor is intrinsically safe; the reactor material, activated during operation, loses practically all its activity within about 100 years. But the working up of the controlled fusion necessitates extreme technological conditions. In 1979, the Joint European Torus (JET) began its operation; today it is still the most powerful tokamak in the world; its energy yield Q reached 0.65. The progress realized in the framework of EURATOM has led to the planning of the experimental reactor ITER which is being built at Cadarache (France). ITER is designed to reach a Q-value largely above 1. The future prototype reactor DEMO is foreseen in 2040-2050. It should demonstrate the ability of a fusion reactor to inject electricity into the grid for long term. In 2014, CRPP participated in the works on ITER in the framework of the Fusion for Energy (F4E) agency. At EPFL the research concerns the physics of the magnetic confinement with experiments on the tokamak TCV (variable configuration tokamak), the numerical simulations, the plasma heating and the generation of current by hyper frequency radio waves. At the Paul Scherrer Institute (PSI), research is devoted to the superconductivity. At the Basel University the studies get on interactions between the plasma and the tokamak walls. The large flexibility of TCV allows creating and controlling plasmas of different shapes which are necessary to optimise the core geometry of future reactors. Moreover, the plasma heating by mm radio waves allows guiding the injected power according to specific

Collisionless ion drag force on a spherical grain

International Nuclear Information System (INIS)

Hutchinson, I H

2006-01-01

The ion drag force on a spherical grain situated in a flowing collisionless plasma is obtained from the specialized coordinate electrostatic particle and thermals in cell simulation code (SCEPTIC) (Hutchinson 2002 Plasma Phys. Control. Fusion 44 1953, Hutchinson 2003 Plasma Phys. Control. Fusion 45 1477, Hutchinson 2005 Plasma Phys. Control. Fusion 47 71) and compared with recent analytic approximate treatments in the interesting and relevant case when the Debye length is only moderately larger than the sphere radius. There is a substantial complex structure in the results for transonic flows, which is explained in terms of the details of ion orbits. Naturally the prior analytic approximations miss this structure, and as a result they seriously underestimate the drag for speeds near the sound speed. An easy-to-evaluate expression for force is provided that fits the comprehensive results of the code. This expression, with minor modification, also fits the results even for Debye length much smaller than the sphere radius

Experimental and neoclassical electron heat transport in the LMFP regime for the stellarators W7-A, L-2, and W7-AS

International Nuclear Information System (INIS)

Maassberg, H.; Burhenn, R.; Gasparino, U.; Kuehner, G.; Ringler, H.; Dyabilin, K.S.

1993-01-01

The electron energy balance is analyzed for equivalent low-density electron cyclotron resonance heated (ECRH) discharges with highly peaked central power deposition in the stellarators W7-A [Plasma Phys. Controlled Fusion 28, 43 (1986)], L-2 [Proceedings of the 6th International Conference on Plasma Physics and Controlled Nuclear Fusion Research, Berchtesgaden, 1976 (International Atomic Energy Agency, Vienna, 1977), Vol. 2, p. 115] and W7-AS [Proceedings of the 9th International Conference on Plasma Physics and Controlled Nuclear Fusion Research, Baltimore, 1982 (International Atomic Energy Agency, Vienna, 1983), Vol. 3, p. 141]. Within the long mean-free path (LMFP) collisionality regime in stellarators, the neoclassical electron heat diffusivity χ e can overcome the ''anomalous'' one. The neoclassical transport coefficients are calculated by the DKES code (Drift Kinetic Equation Solver) [Phys. Fluids 29, 2951 (1986); Phys. Fluids B 1, 563 (1989)] for these configurations, and the particle and energy fluxes are estimated based on measured density and temperature profiles

Control of plasma layer in a fusion reactor correlated to DC motor control using PSO-ANFIS

International Nuclear Information System (INIS)

Mahapatra, Sakuntala; Daniel, Raju; Dey, Deep Narayan

2013-01-01

Plasma position and shape control is very crucial for the overall performance of the fusion reactor such as Tokamak. The quality of the discharge in the Saskatchewan TORus-Modified (STOR-M) tokamak is strongly related to the position of the plasma column within the discharge vessel. If the plasma column approaches too near the wall, then either minor or complete disruption occurs. Consequently it is necessary to be able to control dynamically the position of the plasma column throughout the entire discharge. Now a day's most fusion reactor employs the traditional PID controller for the confinement of plasma layer. Fuzzy logic is used for the control of Plasma layer. In this paper we have used the hybrid of PSO-ANFIS technique to control the speed of a DC motor. We have used two input parameters like speed, torque and output is firing angle. In our work first order Sugeno fuzzy model is taken with three rules and the parameters of Gaussian membership function is controlled by the PSO technique. PSO-ANFIS speed controller obtains better dynamic behavior and superior performance of the DC motor speed control. Similar approach can be correlated to the control of plasma layer. For the plasma control two inputs can be taken as plasma position ΔH and the plasma current and the single output, the control decision u(t). (author)

Operating large controlled thermonuclear fusion research facilities

International Nuclear Information System (INIS)

Gaudreau, M.P.J.; Tarrh, J.M.; Post, R.S.; Thomas, P.

1987-10-01

The MIT Tara Tandem Mirror is a large, state of the art controlled thermonuclear fusion research facility. Over the six years of its design, implementation, and operation, every effort was made to minimize cost and maximize performance by using the best and latest hardware, software, and scientific and operational techniques. After reviewing all major DOE fusion facilities, an independent DOE review committee concluded that the Tara operation was the most automated and efficient of all DOE facilities. This paper includes a review of the key elements of the Tara design, construction, operation, management, physics milestones, and funding that led to this success. We emphasize a chronological description of how the system evolved from the proposal stage to a mature device with an emphasis on the basic philosophies behind the implementation process. This description can serve both as a qualitative and quantitative database for future large experiment planning. It includes actual final costs and manpower spent as well as actual run and maintenance schedules, number of data shots, major system failures, etc. The paper concludes with recommendations for the next generation of facilities. 13 refs., 15 figs., 3 tabs

Computational and biological characterization of fusion proteins of two insecticidal proteins for control of insect pests.

Science.gov (United States)

Javaid, Shaista; Naz, Sehrish; Amin, Imran; Jander, Georg; Ul-Haq, Zaheer; Mansoor, Shahid

2018-03-19

Sucking pests pose a serious agricultural challenge, as available transgenic technologies such as Bacillus thuringiensis crystal toxins (Bt) are not effective against them. One approach is to produce fusion protein toxins for the control of these pests. Two protein toxins, Hvt (ω-atracotoxin from Hadronyche versuta) and onion leaf lectin, were translationally fused to evaluate the negative effects of fusion proteins on Phenacoccus solenopsis (mealybug), a phloem-feeding insect pest. Hvt was cloned both N-terminally (HL) and then C-terminally (LH) in the fusion protein constructs, which were expressed transiently in Nicotiana tabacum using a Potato Virus X (PVX) vector. The HL fusion protein was found to be more effective against P. solenopsis, with an 83% mortality rate, as compared to the LH protein, which caused 65% mortality. Hvt and lectin alone caused 42% and 45%, respectively, under the same conditions. Computational studies of both fusion proteins showed that the HL protein is more stable than the LH protein. Together, these results demonstrate that translational fusion of two insecticidal proteins improved the insecticidal activity relative to each protein individually and could be expressed in transgenic plants for effective control of sucking pests.

Modular control of fusion power heating applications

International Nuclear Information System (INIS)

Demers, D. R.

2012-01-01

This work is motivated by the growing demand for auxiliary heating on small and large machines worldwide. Numerous present and planned RF experiments (EBW, Lower Hybrid, ICRF, and ECH) are increasingly complex systems. The operational challenges are indicative of a need for components of real-time control that can be implemented with a moderate amount of effort in a time- and cost-effective fashion. Such a system will improve experimental efficiency, enhance experimental quality, and expedite technological advancements. The modular architecture of this control-suite serves multiple purposes. It facilitates construction on various scales from single to multiple controller systems. It enables expandability of control from basic to complex via the addition of modules with varying functionalities. It simplifies the control implementation process by reducing layers of software and electronic development. While conceived with fusion applications in mind, this suite has the potential to serve a broad range of scientific and industrial applications. During the Phase-I research effort we established the overall feasibility of this modular control-suite concept. We developed the fundamental modules needed to implement open-loop active-control and demonstrated their use on a microwave power deposition experiment

Local control station for development, testing and maintenance of mirror fusion facility subsystem controls

International Nuclear Information System (INIS)

Ables, E.; Kelly, M.F.

1985-01-01

A Local Control Station (LCS) was designed and built to provide a simplified ad easily configurable means of controlling any Mirror Fusion Test Facility (MFTF-B) subsystem for the purpose of development, testing and maintenance of the subsystem. All MFTF-B Subsystems incorporate at least one Local Control Computer (LCC) that is connected to and accepts high level commands from one of the Supervisory Control and Diagnostic System (SCDS) computers. The LCS connects directly to the LCC in place of SCDS. The LCS communicates with the subsystem hardware using the same SCDS commands that the local control computer recognizes and as such requires no special configuration of the LCC

Sensor fusion IV: Control paradigms and data structures; Proceedings of the Meeting, Boston, MA, Nov. 12-15, 1991

Science.gov (United States)

Schenker, Paul S. (Editor)

1992-01-01

Various papers on control paradigms and data structures in sensor fusion are presented. The general topics addressed include: decision models and computational methods, sensor modeling and data representation, active sensing strategies, geometric planning and visualization, task-driven sensing, motion analysis, models motivated biology and psychology, decentralized detection and distributed decision, data fusion architectures, robust estimation of shapes and features, application and implementation. Some of the individual subjects considered are: the Firefly experiment on neural networks for distributed sensor data fusion, manifold traversing as a model for learning control of autonomous robots, choice of coordinate systems for multiple sensor fusion, continuous motion using task-directed stereo vision, interactive and cooperative sensing and control for advanced teleoperation, knowledge-based imaging for terrain analysis, physical and digital simulations for IVA robotics.

Macrophage fusion is controlled by the cytoplasmic protein tyrosine phosphatase PTP-PEST/PTPN12.

Science.gov (United States)

Rhee, Inmoo; Davidson, Dominique; Souza, Cleiton Martins; Vacher, Jean; Veillette, André

2013-06-01

Macrophages can undergo cell-cell fusion, leading to the formation of multinucleated giant cells and osteoclasts. This process is believed to promote the proteolytic activity of macrophages toward pathogens, foreign bodies, and extracellular matrices. Here, we examined the role of PTP-PEST (PTPN12), a cytoplasmic protein tyrosine phosphatase, in macrophage fusion. Using a macrophage-targeted PTP-PEST-deficient mouse, we determined that PTP-PEST was not needed for macrophage differentiation or cytokine production. However, it was necessary for interleukin-4-induced macrophage fusion into multinucleated giant cells in vitro. It was also needed for macrophage fusion following implantation of a foreign body in vivo. Moreover, in the RAW264.7 macrophage cell line, PTP-PEST was required for receptor activator of nuclear factor kappa-B ligand (RANKL)-triggered macrophage fusion into osteoclasts. PTP-PEST had no impact on expression of fusion mediators such as β-integrins, E-cadherin, and CD47, which enable macrophages to become fusion competent. However, it was needed for polarization of macrophages, migration induced by the chemokine CC chemokine ligand 2 (CCL2), and integrin-induced spreading, three key events in the fusion process. PTP-PEST deficiency resulted in specific hyperphosphorylation of the protein tyrosine kinase Pyk2 and the adaptor paxillin. Moreover, a fusion defect was induced upon treatment of normal macrophages with a Pyk2 inhibitor. Together, these data argue that macrophage fusion is critically dependent on PTP-PEST. This function is seemingly due to the ability of PTP-PEST to control phosphorylation of Pyk2 and paxillin, thereby regulating cell polarization, migration, and spreading.

Target design for high fusion yield with the double Z-pinch-driven hohlraum

International Nuclear Information System (INIS)

Vesey, R. A.; Herrmann, M. C.; Lemke, R. W.; Desjarlais, M. P.; Cuneo, M. E.; Stygar, W. A.; Bennett, G. R.; Campbell, R. B.; Christenson, P. J.; Mehlhorn, T. A.; Porter, J. L.; Slutz, S. A.

2007-01-01

A key demonstration on the path to inertial fusion energy is the achievement of high fusion yield (hundreds of MJ) and high target gain. Toward this goal, an indirect-drive high-yield inertial confinement fusion (ICF) target involving two Z-pinch x-ray sources heating a central secondary hohlraum is described by Hammer et al. [Phys. Plasmas 6, 2129 (1999)]. In subsequent research at Sandia National Laboratories, theoretical/computational models have been developed and an extensive series of validation experiments have been performed to study hohlraum energetics, capsule coupling, and capsule implosion symmetry for this system. These models have been used to design a high-yield Z-pinch-driven ICF target that incorporates the latest experience in capsule design, hohlraum symmetry control, and x-ray production by Z pinches. An x-ray energy output of 9 MJ per pinch, suitably pulse-shaped, is sufficient for this concept to drive 0.3-0.5 GJ capsules. For the first time, integrated two-dimensional (2D) hohlraum/capsule radiation-hydrodynamics simulations have demonstrated adequate hohlraum coupling, time-dependent radiation symmetry control, and the successful implosion, ignition, and burn of a high-yield capsule in the double Z-pinch hohlraum. An important new feature of this target design is mode-selective symmetry control: the use of burn-through shields offset from the capsule that selectively tune certain low-order asymmetry modes (P 2 ,P 4 ) without significantly perturbing higher-order modes and without a significant energy penalty. This paper will describe the capsule and hohlraum design that have produced 0.4-0.5 GJ yields in 2D simulations, provide a preliminary estimate of the Z-pinch load and accelerator requirements necessary to drive the system, and suggest future directions for target design work

Controllers for high-performance nuclear fusion plasmas

NARCIS (Netherlands)

Baar, de M.R.

2012-01-01

A succesful nuclear fusion reactor will confine plasma at hig temperatures and densities, with low thermal losses. The workhorse of the nuclear fusion community is the tokamak, a toroidal device in which plasmas are confined by poloidal and toroidal magnetic fields. Ideally, the confirming magnetic

Multi-agent control system with information fusion based comfort model for smart buildings

International Nuclear Information System (INIS)

Wang, Zhu; Wang, Lingfeng; Dounis, Anastasios I.; Yang, Rui

2012-01-01

Highlights: ► Proposed a model to manage indoor energy and comfort for smart buildings. ► Developed a control system to maximize comfort with minimum energy consumption. ► Information fusion with ordered weighted averaging aggregation is used. ► Multi-agent technology and heuristic intelligent optimization are deployed in developing the control system. -- Abstract: From the perspective of system control, a smart and green building is a large-scale dynamic system with high complexity and a huge amount of information. Proper combination of the available information and effective control of the overall building system turns out to be a big challenge. In this study, we proposed a building indoor energy and comfort management model based on information fusion using ordered weighted averaging (OWA) aggregation. A multi-agent control system with heuristic intelligent optimization is developed to achieve a high level of comfort with the minimum power consumption. Case studies and simulation results are presented and discussed in this paper.

Fusion--fission hybrid concepts for laser-induced fusion

International Nuclear Information System (INIS)

Maniscalco, J.

1976-01-01

Fusion-fission hybrid concepts are viewed as subcritical fission reactors driven and controlled by high-energy neutrons from a laser-induced fusion reactor. Blanket designs encompassing a substantial portion of the spectrum of different fission reactor technologies are analyzed and compared by calculating their fissile-breeding and fusion-energy-multiplying characteristics. With a large number of different fission technologies to choose from, it is essential to identify more promising hybrid concepts that can then be subjected to in-depth studies that treat the engineering safety, and economic requirements as well as the neutronic aspects. In the course of neutronically analyzing and comparing several fission blanket concepts, this work has demonstrated that fusion-fission hybrids can be designed to meet a broad spectrum of fissile-breeding and fusion-energy-multiplying requirements. The neutronic results should prove to be extremely useful in formulating the technical scope of future studies concerned with evaluating the technical and economic feasibility of hybrid concepts for laser-induced fusion

A Multiple Data Fusion Approach to Wheel Slip Control for Decentralized Electric Vehicles

Directory of Open Access Journals (Sweden)

Dejun Yin

2017-04-01

Full Text Available Currently, active safety control methods for cars, i.e., the antilock braking system (ABS, the traction control system (TCS, and electronic stability control (ESC, govern the wheel slip control based on the wheel slip ratio, which relies on the information from non-driven wheels. However, these methods are not applicable in the cases without non-driven wheels, e.g., a four-wheel decentralized electric vehicle. Therefore, this paper proposes a new wheel slip control approach based on a novel data fusion method to ensure good traction performance in any driving condition. Firstly, with the proposed data fusion algorithm, the acceleration estimator makes use of the data measured by the sensor installed near the vehicle center of mass (CM to calculate the reference acceleration of each wheel center. Then, the wheel slip is constrained by controlling the acceleration deviation between the actual wheel and the reference wheel center. By comparison with non-control and model following control (MFC cases in double lane change tests, the simulation results demonstrate that the proposed control method has significant anti-slip effectiveness and stabilizing control performance.

Linear stability analysis of double ablation fronts in direct-drive inertial confinement fusion

International Nuclear Information System (INIS)

Yanez, C.; Sanz, J.; Ibanez, L. F.; Olazabal-Loume, M.

2011-01-01

A linear stability theory of double ablation fronts is developed for direct-drive inertial confinement fusion targets. The so-called electron radiative ablation front [S. Fujioka et al., Phys. Rev. Lett. 92, 195001 (2004)] is studied with a self-consistent model. Numerical results are presented as well as an analytical approach for the radiation dominated regime of very steep double ablation front structure. Dispersion relation formula is tackled by means of a sharp boundary model.

Some introductory notes on the problem of nuclear energy by controlled fusion reactions

International Nuclear Information System (INIS)

Pedretti, E.

1988-01-01

Written for scientists and technologist interested in, but unfamiliar with nuclear energy by controlled fusion reactions, this ''sui generis'' review paper attempts to provide the reader, as shortly as possible, with a general idea of the main issues at stake in nuclear fusion research. With the purpose of keeping this paper within a reasonable length, the various subjects are only outlined in their essence, basic features, underlying principles, etc., without entering into details, which are left to the quoted literature. Due to the particular readership of this journal, vacuum problems and/or aspects of fusion research anyhow related with vacuum science and technology are evidentiated. After reviewing fusion reactions' cross sections, fusion by accelerators and muon catalyzed fusion are described, followed by mention of Lawson's criteria and of plasma confinement features. Then, inertial confinement fusion is dealt with, also including one example of laser system (Nova), one of accelerator facility (PBFA-II) and some guesses on the classified Centurion-Halite program. Magnetic confinement fusion research is also reviewed, in particulary reporting one example of linear machine (MFTF-B), two examples of toroidal machines other than Tokamak (ATF and Eta-Beta-II) and various examples of Tokamaks, including PBX and PBX-M; TFTR, JET, JT-60, T-15 and Tore-Supra (large machines); Alcator A, FT, Alcator C/MTX, Alcator C-Mod and T-14 (compact high field machines). Tokamaks under design for ignition experiments (Ignitor, CIT, Ignitex and NET) are also illustrated. Thermal conversion of fusion power and direct generation of electricity are mentioned; conceptual design of fusion power plants are considered and illustrated by four examples (STARFIRE, WILDCAT, MARS and CASCADE). The D 3 He fuel cycle is discussed as an alternative more acceptable than Deuterium-Tritium, and thw Candor proposal is reported. After recalling past experience of the fission power development, some

Assessment of ion kinetic effects in shock-driven inertial confinement fusion implosions using fusion burn imaging

International Nuclear Information System (INIS)

Rosenberg, M. J.; Séguin, F. H.; Rinderknecht, H. G.; Zylstra, A. B.; Li, C. K.; Sio, H.; Johnson, M. Gatu; Frenje, J. A.; Petrasso, R. D.; Amendt, P. A.; Wilks, S. C.; Pino, J.; Atzeni, S.; Hoffman, N. M.; Kagan, G.; Molvig, K.; Glebov, V. Yu.; Stoeckl, C.; Seka, W.; Marshall, F. J.

2015-01-01

The significance and nature of ion kinetic effects in D 3 He-filled, shock-driven inertial confinement fusion implosions are assessed through measurements of fusion burn profiles. Over this series of experiments, the ratio of ion-ion mean free path to minimum shell radius (the Knudsen number, N K ) was varied from 0.3 to 9 in order to probe hydrodynamic-like to strongly kinetic plasma conditions; as the Knudsen number increased, hydrodynamic models increasingly failed to match measured yields, while an empirically-tuned, first-step model of ion kinetic effects better captured the observed yield trends [Rosenberg et al., Phys. Rev. Lett. 112, 185001 (2014)]. Here, spatially resolved measurements of the fusion burn are used to examine kinetic ion transport effects in greater detail, adding an additional dimension of understanding that goes beyond zero-dimensional integrated quantities to one-dimensional profiles. In agreement with the previous findings, a comparison of measured and simulated burn profiles shows that models including ion transport effects are able to better match the experimental results. In implosions characterized by large Knudsen numbers (N K  ∼ 3), the fusion burn profiles predicted by hydrodynamics simulations that exclude ion mean free path effects are peaked far from the origin, in stark disagreement with the experimentally observed profiles, which are centrally peaked. In contrast, a hydrodynamics simulation that includes a model of ion diffusion is able to qualitatively match the measured profile shapes. Therefore, ion diffusion or diffusion-like processes are identified as a plausible explanation of the observed trends, though further refinement of the models is needed for a more complete and quantitative understanding of ion kinetic effects

Assessment of ion kinetic effects in shock-driven inertial confinement fusion implosions using fusion burn imaging

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, M. J., E-mail: mros@lle.rochester.edu; Séguin, F. H.; Rinderknecht, H. G.; Zylstra, A. B.; Li, C. K.; Sio, H.; Johnson, M. Gatu; Frenje, J. A.; Petrasso, R. D. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Amendt, P. A.; Wilks, S. C.; Pino, J. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Atzeni, S. [Dipartimento SBAI, Università di Roma “La Sapienza” and CNISM, Via A. Scarpa 14-16, I-00161 Roma (Italy); Hoffman, N. M.; Kagan, G.; Molvig, K. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Glebov, V. Yu.; Stoeckl, C.; Seka, W.; Marshall, F. J. [Laboratory for Laser Energetics, University of Rochester, Rochester, New York 14623 (United States); and others

2015-06-15

The significance and nature of ion kinetic effects in D{sup 3}He-filled, shock-driven inertial confinement fusion implosions are assessed through measurements of fusion burn profiles. Over this series of experiments, the ratio of ion-ion mean free path to minimum shell radius (the Knudsen number, N{sub K}) was varied from 0.3 to 9 in order to probe hydrodynamic-like to strongly kinetic plasma conditions; as the Knudsen number increased, hydrodynamic models increasingly failed to match measured yields, while an empirically-tuned, first-step model of ion kinetic effects better captured the observed yield trends [Rosenberg et al., Phys. Rev. Lett. 112, 185001 (2014)]. Here, spatially resolved measurements of the fusion burn are used to examine kinetic ion transport effects in greater detail, adding an additional dimension of understanding that goes beyond zero-dimensional integrated quantities to one-dimensional profiles. In agreement with the previous findings, a comparison of measured and simulated burn profiles shows that models including ion transport effects are able to better match the experimental results. In implosions characterized by large Knudsen numbers (N{sub K} ∼ 3), the fusion burn profiles predicted by hydrodynamics simulations that exclude ion mean free path effects are peaked far from the origin, in stark disagreement with the experimentally observed profiles, which are centrally peaked. In contrast, a hydrodynamics simulation that includes a model of ion diffusion is able to qualitatively match the measured profile shapes. Therefore, ion diffusion or diffusion-like processes are identified as a plausible explanation of the observed trends, though further refinement of the models is needed for a more complete and quantitative understanding of ion kinetic effects.

Design of power control system using SMES and SVC for fusion power plant

International Nuclear Information System (INIS)

Niiyama, K; Yagai, T; Tsuda, M; Hamajima, T

2008-01-01

A SMES (Superconducting Magnetic Energy Storage System) system with converter composed of self-commutated valve devices such as GTO and IGBT is available to control active and reactive power simultaneously. A SVC (Static Var Compensators) or STATCOM (Static Synchronous Compensator) is widely employed to reduce reactive power in power plants and substations. Owing to progress of power electronics technology using GTO and IGBT devices, power converters in the SMES system and the SVC can easily control power flow in few milliseconds. Moreover, since the valve devices for the SMES are equivalent to those for the SVC, the device cost must be reduced. In this paper the basic control system combined with the SMES and SVC is designed for large pulsed loads of a nuclear fusion power plant. This combined system largely expands the reactive power control region as well as the active one. The simulation results show that the combined system is effective and prospective for the nuclear fusion power plant

Controlled thermonuclear fusion power apparatus and method

International Nuclear Information System (INIS)

Bussard, R.W.; Coppi, B.

1982-01-01

This invention provides a modular fusion reactor system containing several fusion power cores, each of relatively small size and low cost. Energy from the cores is absorbed in the core structure and within a surrounding blanket, and the cores themselves may be individually removed from the blanket and replaced as they deteriorate from high radiation flux damage

Control of a laser inertial confinement fusion-fission power plant

Science.gov (United States)

Moses, Edward I.; Latkowski, Jeffery F.; Kramer, Kevin J.

2015-10-27

A laser inertial-confinement fusion-fission energy power plant is described. The fusion-fission hybrid system uses inertial confinement fusion to produce neutrons from a fusion reaction of deuterium and tritium. The fusion neutrons drive a sub-critical blanket of fissile or fertile fuel. A coolant circulated through the fuel extracts heat from the fuel that is used to generate electricity. The inertial confinement fusion reaction can be implemented using central hot spot or fast ignition fusion, and direct or indirect drive. The fusion neutrons result in ultra-deep burn-up of the fuel in the fission blanket, thus enabling the burning of nuclear waste. Fuels include depleted uranium, natural uranium, enriched uranium, spent nuclear fuel, thorium, and weapons grade plutonium. LIFE engines can meet worldwide electricity needs in a safe and sustainable manner, while drastically shrinking the highly undesirable stockpiles of depleted uranium, spent nuclear fuel and excess weapons materials.

Modeling of active control of external magnetohydrodynamic instabilities

International Nuclear Information System (INIS)

Bialek, James; Boozer, Allen H.; Mauel, M.E.; Navratil, G.A.

2001-01-01

A general circuit formulation of resistive wall mode (RWM) feedback stabilization developed by Boozer [Phys. Plasmas 5, 3350 (1998)] has been used as the basis for the VALEN computer code that calculates the performance of an active control system in arbitrary geometry. The code uses a finite element representation of a thin shell structure in an integral formulation to model arbitrary conducting walls. This is combined with a circuit representation of stable and unstable plasma modes. Benchmark comparisons of VALEN results with large aspect ratio analytic model of the current driven kink mode are in very good agreement. VALEN also models arbitrary sensors, control coils, and the feedback logic connecting these sensors and control coils to provide a complete simulation capability for feedback control of plasma instabilities. VALEN modeling is in good agreement with experimental results on DIII-D [Garofalo et al., Nucl. Fusion 40, 1491 (2000)] and HBT-EP [Cates et al., Phys. Plasmas 7, 3133 (2000)]. VALEN feedback simulations have also been used to evaluate and optimize the sensor/coil configurations for present and planned RWM experiments on DIII-D. These studies have shown a clear advantage for the use of local poloidal field sensors driving a 'mode control' feedback logic control loop and configurations which minimize the control coil coupling to the stabilizing resistive wall

Magnetic fusion technology

CERN Document Server

Dolan, Thomas J

2014-01-01

Magnetic Fusion Technology describes the technologies that are required for successful development of nuclear fusion power plants using strong magnetic fields. These technologies include: ? magnet systems, ? plasma heating systems, ? control systems, ? energy conversion systems, ? advanced materials development, ? vacuum systems, ? cryogenic systems, ? plasma diagnostics, ? safety systems, and ? power plant design studies. Magnetic Fusion Technology will be useful to students and to specialists working in energy research.

Atomic physics issues in fusion

International Nuclear Information System (INIS)

Post, D.E.

1982-01-01

Atomic physics issues have played a large role in controlled fusion research. A general introduction to the present role of atomic processes in both inertial and magnetic controlled fusion work is presented. (Auth.)

Bringing fusion electric power closer

International Nuclear Information System (INIS)

Kintner, E.

1977-01-01

A review of the controlled fusion research program is given. The tokamak research program is described. Beam injection heating, control systems, and the safety of fusion reactors are topics that are also discussed

Integrated predictive modelling simulations of burning plasma experiment designs

International Nuclear Information System (INIS)

Bateman, Glenn; Onjun, Thawatchai; Kritz, Arnold H

2003-01-01

Models for the height of the pedestal at the edge of H-mode plasmas (Onjun T et al 2002 Phys. Plasmas 9 5018) are used together with the Multi-Mode core transport model (Bateman G et al 1998 Phys. Plasmas 5 1793) in the BALDUR integrated predictive modelling code to predict the performance of the ITER (Aymar A et al 2002 Plasma Phys. Control. Fusion 44 519), FIRE (Meade D M et al 2001 Fusion Technol. 39 336), and IGNITOR (Coppi B et al 2001 Nucl. Fusion 41 1253) fusion reactor designs. The simulation protocol used in this paper is tested by comparing predicted temperature and density profiles against experimental data from 33 H-mode discharges in the JET (Rebut P H et al 1985 Nucl. Fusion 25 1011) and DIII-D (Luxon J L et al 1985 Fusion Technol. 8 441) tokamaks. The sensitivities of the predictions are evaluated for the burning plasma experimental designs by using variations of the pedestal temperature model that are one standard deviation above and below the standard model. Simulations of the fusion reactor designs are carried out for scans in which the plasma density and auxiliary heating power are varied

v-SNAREs control exocytosis of vesicles from priming to fusion.

Science.gov (United States)

Borisovska, Maria; Zhao, Ying; Tsytsyura, Yaroslav; Glyvuk, Nataliya; Takamori, Shigeo; Matti, Ulf; Rettig, Jens; Südhof, Thomas; Bruns, Dieter

2005-06-15

SNARE proteins (soluble NSF-attachment protein receptors) are thought to be central components of the exocytotic mechanism in neurosecretory cells, but their precise function remained unclear. Here, we show that each of the vesicle-associated SNARE proteins (v-SNARE) of a chromaffin granule, synaptobrevin II or cellubrevin, is sufficient to support Ca(2+)-dependent exocytosis and to establish a pool of primed, readily releasable vesicles. In the absence of both proteins, secretion is abolished, without affecting biogenesis or docking of granules indicating that v-SNAREs are absolutely required for granule exocytosis. We find that synaptobrevin II and cellubrevin differentially control the pool of readily releasable vesicles and show that the v-SNARE's amino terminus regulates the vesicle's primed state. We demonstrate that dynamics of fusion pore dilation are regulated by v-SNAREs, indicating their action throughout exocytosis from priming to fusion of vesicles.

Research programme on controlled thermonuclear fusion. Synthesis report 2011

International Nuclear Information System (INIS)

Vaucher, C.; Tran, M. Q.; Villard, L.; Marot, L.

2012-01-01

Since 1978, research on thermonuclear fusion in Switzerland is closely related to the research programme of the European Atomic Energy Community (EURATOM). The Swiss projects tackle aspects of plasma physics and fusion technology. Switzerland participates to the construction and operation of the Joint European Torus (JET), which started operation again in 2011. The International Thermonuclear Experimental Reactor (ITER) is the last step before DEMO, a prototype fusion reactor able to deliver electricity and demonstrate the economic viability of fusion energy. The 'Centre de Recherches en Physique des Plasmas' (CRPP) of the EPFL went on with its participation to the scientific and technological programme of EURATOM. Researches are carried out essentially on 2 sites: (i) at EPFL, where topics dealt with include the physics of magnetic confinement studied using the Variable Configuration Tokamak (TCV), the basic experiment TORPEX, theory and numerical modelling, and the technology of plasma heating and current generation by hyper-frequency waves; (ii) at the Paul Scherrer Institute (PSI), where activities are devoted to superconductivity and structure materials. Thanks to the large flexibility of the TCV design and operation modus, plasmas of different shapes can be created and controlled, what is a very useful option to verify numerical simulation results. Besides, the injection of millimetre waves allows directing the injected power according to specific profiles. In the TCV it could be demonstrated for the first time that the injection of Electronic Cyclotronic Heating (ECH) waves is able to double the frequency of so-called 'Edge Localized Modes' (ELM), reducing by a factor of 2 the energy expelled by each ELM. In particular, it was possible to considerably reduce the statistical dispersion of the repetition frequency of ELM, and to avoid the appearance of gigantic ELM that are particularly harmful for reactor operation. The effect of plasma internal relaxation

Comment on 'Nonlinear gyrokinetic theory with polarization drift' [Phys. Plasmas 17, 082304 (2010)

International Nuclear Information System (INIS)

Leerink, S.; Parra, F. I.; Heikkinen, J. A.

2010-01-01

In this comment, we show that by using the discrete particle distribution function the changes of the phase-space volume of gyrocenter coordinates due to the fluctuating ExB velocity do not explicitly appear in the Poisson equation and the [Sosenko et al., Phys. Scr. 64, 264 (2001)] result is recovered. It is demonstrated that there is no contradiction between the work presented by Sosenko et al. and the work presented by [Wang et al., Phys. Plasmas 17, 082304 (2010)].

Research program. Controlled thermonuclear fusion. Synthesis report 2013

International Nuclear Information System (INIS)

Villard, L.; Marot, L.

2014-01-01

In 1961, 3 years after the 2 nd International Conference on Peaceful Use of Nuclear Energy, the Research Centre on Plasma Physics (CRPP) was created as a department of the Federal Institute of Technology (EPFL) in Lausanne (Switzerland). From 1979, CRPP collaborates to the European Program on fusion research in the framework of EURATOM. The advantages of fusion are remarkable: the fuel is available in great quantity all over the world; the reactor is intrinsically safe; the reactor material, activated during operation, loses practically all its activity within about 100 years. But the working up of the controlled fusion necessitates extreme technological conditions. The progress realized in the framework of EURATOM has led to the design of the experimental reactor ITER which is being built at Cadarache (France). The future prototype reactor DEMO is foreseen in 2040-2050. In 2013, CRPP participated in the works on ITER in the framework of the Fusion for Energy (F4E) agency. At EPFL the research concerns the physics of the magnetic confinement with experiments on the tokamak TCV (variable configuration tokamak), the numerical simulations, the plasma heating and the generation of current by hyper frequency radio waves. At the Paul Scherrer Institute (PSI), research is devoted to the superconductivity. At the Basel University the studies get on interactions between the plasma and the tokamak walls. A new improved confinement regime, called IN-mode, was discovered on TCV. The theory and numerical simulation group interprets the experimental results and foresees those of futures machines. It requires very high performance computers. The Gyrotron group develops radiofrequency sources in the mm range for heating the TCV plasma as well as for ITER and the Wendelstein-7 stellarator. Concerning superconductivity, tests are conducted at PSI on toroidal cables of ITER. The development of conductors and coils for the DEMO reactor has been pursued. In the context of international

Research program. Controlled thermonuclear fusion. Synthesis report 2015

International Nuclear Information System (INIS)

Villard, L.; Marot, L.; Soom, P.

2016-01-01

In 1961, 3 years after the 2 nd International Conference on Peaceful Use of Nuclear Energy, the Research Centre on Plasma Physics (CRPP) was created as a department of the Federal Institute of Technology (EPFL) in Lausanne (Switzerland). From 1979, CRPP collaborates to the European Program on fusion research in the framework of EURATOM. In 2015 its name was changed to Swiss Plasma Centre (SPC). The advantages of fusion are remarkable: the fuel is available in great quantity all over the world; the reactor is intrinsically safe; the reactor material, activated during operation, loses practically all its activity within about 100 years. But the working up of the controlled fusion necessitates extreme technological conditions. In 1979, the Joint European Torus (JET) began its operation; today it is still the most powerful tokamak in the world, in which an energy yield Q of 0.65 could be obtained. In 2015, the stellarator Wendelstein 7-X (W7X), the largest in the world, was set into operation. The progress realized in the framework of EURATOM has led to the planning of the experimental reactor ITER which is being built at Cadarache (France). ITER is designed to reach a Q-value largely above 1. The future prototype reactor DEMO is foreseen in 2040-2050. It should demonstrate the ability of a fusion reactor to inject permanently electricity into the grid. In 2015, SPC participated in the works on ITER in the framework of the Fusion for Energy (F4E) agency. At EPFL the research concerns the physics of the magnetic confinement with experiments on the tokamak TCV (variable configuration tokamak), the numerical simulations, the plasma heating and the generation of current by hyper frequency radio waves. At the Paul Scherrer Institute (PSI), research is devoted to the superconductivity; at the Basel University the studies get on interactions between the plasma and the tokamak walls. The large flexibility of TCV allows creating and controlling plasmas of different shapes which

Conceptual requirements for large fusion experiment control, data, robotics, and management systems

International Nuclear Information System (INIS)

Gaudreau, M.P.J.; Sullivan, J.D.

1987-05-01

The conceptual system requirements for the control, data, robotics, and project management (CDRM) system for the next generation of fusion experiments are developed by drawing on the success of the Tara control and data system. The requirements are described in terms of an integrated but separable matrix of well-defined interfaces among the various systems and subsystems. The study stresses modularity, performance, cost effectiveness, and exportability

Plasma Physics and Controlled Nuclear Fusion Research. Vol. II. Proceedings of a Conference on Plasma Physics and Controlled Physics Research

International Nuclear Information System (INIS)

1966-01-01

Research on controlled nuclear fusion was first disclosed at the Second United Nations Conference on the Peaceful Uses of Atomic Energy, held at Geneva in 1958. From the information given, it was evident that a better understanding of the behaviour of hot dense plasmas was needed before the goal of economic energy release from nuclear fusion could be reached. The fact that research since then has been most complex and costly has enhanced the desirability of international co-operation and exchange of information and experience. Having organized its First Conference on Plasma Physics and Controlled Nuclear Fusion Research at Salzburg in 1961, the International Atomic Energy Agency again provided the means for such cooperation in organizing its Second Conference on this subject on 6-10 September, 1965, at Culham, Abingdon, Berks, England. The meeting was arranged with the generous help of the United Kingdom Atomic Energy Authority at their Culham Laboratory, where the facilities and assistance of the staff were greatly appreciated. At the meeting, which was attended by 268 participants from 26 member states and three international organizations, significant results from many experiments, including those from the new and larger machines, became available. It has now become feasible to intercorrelate data obtained from a number of similar machines; this has led to a more complete understanding of plasma behaviour. No breakthrough was reported nor had been expected towards the economical release of the energy from fusion, but there was increased understanding of the problems of production, control and containment of high-density and high-temperature plasmas

Reduced optical transmission of SiO2 fibers used in controlled fusion diagnostics

International Nuclear Information System (INIS)

Ramsey, A.T.; Adler, H.G.; Hill, K.W.

1993-02-01

We have subjected a silica core fiber optic cable to 4 years of low-level neutron and gamma radiation from Princeton's TFTR controlled fusion experiment The accumulated dose was 200 Gy. As a result of the radiation, we have measured increased attenuations of 100--300 db/km in the visible part of the spectrum, and a decrease of the numerical aperture. An attempt to decrease this damage by photobleaching failed. We argue that this failure is not unexpected, since the rate of damage is so slow and the time scale so long that the self-annealing process keeps the residual damage at the irreducible level seen in other experiments. The implications of these findings for controlled fusion diagnostics during upcoming experiments with highly reactive deuterium-tritium plasmas are discussed

Demountable toroidal fusion core facility for physics optimization and fusion engineering

International Nuclear Information System (INIS)

Bogart, S.L.; Wagner, C.E.; Krall, N.A.; Dalessandro, J.A.; Weggel, C.F.; Lund, K.O.; Sedehi, S.

1986-01-01

Following a successful compact ignition tokamak (CIT) experiment, a fusion facility will be required for physics optimization (POF) and fusion engineering research (FERF). The POF will address issues such as high-beta operation, current drive, impurity control, and will test geometric and configurational variations such as the spherical torus or the reversed-field pinch (RFP). The FERF will be designed to accumulate rapidly a large neutron dose in prototypical fusion subsystems exposed to radiation. Both facilities will require low-cost replacement cores and rapid replacement times. The Demountable Toroidal Fusion Core (DTFC) facility is designed to fulfill these requirements. It would be a cost-effective stepping stone between the CIT and a demonstration fusion reactor

Control oriented modeling and simulation of the sawtooth instability in nuclear fusion tokamak plasmas

NARCIS (Netherlands)

Witvoet, G.; Westerhof, E.; Steinbuch, M.; Doelman, N.J.; Baar, de M.R.

2009-01-01

Tokamak plasmas in nuclear fusion are subject to various instabilities. A clear example is the sawtooth instability, which has both positive and negative effects on the plasma. To optimize between these effects control of the sawtooth period is necessary. This paper presents a simple control

Synthetic report 2012. Research programme on controlled thermonuclear fusion

International Nuclear Information System (INIS)

Vaucher, C.; Tran, M. Q.; Villard, L.; Marot, L.

2013-01-01

Since 1961, Switzerland participates in the research on thermonuclear fusion thanks to the creation of the Research Centre in Plasma Physics. In 1979 it entered into partnership with the European programme on fusion through its adhesion to EURATOM. The thermonuclear fusion is an interesting energy source because the basic fuel is practically inexhaustible and its use does not release any significant CO 2 quantity and very little radioactive residues. But its working up faces enormous physical and technological difficulties. The International Thermonuclear Reactor (ITER), presently in construction, has to demonstrate the technological feasibility of the controlled fusion. Il will be followed by DEMO, foreseen for 2040-2050, which must guarantee the economical rentability. At CRPP the research projects are partitioned onto several sites: at the Swiss Federal Institute of Technology (EPFL) in Lausanne, they concern the physics of the magnetic confinement with the Variable Geometry Tokamak (TCV), the development of theoretical models and the numerical simulation, the plasma heating and the generation of hyper frequency waves; the Paul Scherrer Institute (PSI) studies the superconductivity and the materials; the interactions between the plasma and the Tokamak walls are studied at the Basel University for the structures of ITER. Thanks to its large flexibility, TCV allows the creation and the control of plasmas of very different forms. The injection system of millimetric waves allows orienting the injected power according to specific profiles. By using the asymmetry of the flow in the toroidal sense, the plasma rotation could be measured with a much better accuracy than before. In TCV, by playing on the form of the plasma, it was possible to strongly reduce the energy quantity which is expelled by the Edge Localized Modes (ELM) onto the wall of the vacuum chamber. The ‘snowflake’ configuration created in TCV allows distributing the ELM energy onto several impact

The European programme for controlled nuclear fusion

International Nuclear Information System (INIS)

This illustrated document is intended for information only and should not be used as a technical reference. The nuclear fusion reactors are presented with the two approaches: magnetic confinement and inertial confinement; are described: the place of fusion in the world energy scene and its importance for Europe, how research is at present organized, and the European programme with this next stage: the JET (Joint European Torus), the largest tokamak machine in Europe

Plasma physics and controlled nuclear fusion research 1990. V. 1

International Nuclear Information System (INIS)

1991-01-01

Volume 1 of the Proceedings of the Thirteenth International Conference on Plasma Physics and Controlled Nuclear Fusion Research contains papers given in two of the sessions: A and E. Session A contains the Artsimovich Memorial Lecture and papers on tokamaks; session E papers on plasma heating and current drive. The titles and authors of each paper are listed in the Contents. Abstracts accompany each paper. Refs, figs and tabs

BOOK REVIEW: Controlled Fusion and Plasma Physics

Science.gov (United States)

Engelmann, F.

2007-07-01

This new book by Kenro Miyamoto provides an up-to-date overview of the status of fusion research and the important parts of the underlying plasma physics at a moment where, due to the start of ITER construction, an important step in fusion research has been made and many new research workers will enter the field. For them, and also for interested graduate students and physicists in other fields, the book provides a good introduction into fusion physics as, on the whole, the presentation of the material is quite appropriate for getting acquainted with the field on the basis of just general knowledge in physics. There is overlap with Miyamoto's earlier book Plasma Physics for Nuclear Fusion (MIT Press, Cambridge, USA, 1989) but only in a few sections on subjects which have not evolved since. The presentation is subdivided into two parts of about equal length. The first part, following a concise survey of the physics basis of thermonuclear fusion and of plasmas in general, covers the various magnetic configurations studied for plasma confinement (tokamak; reversed field pinch; stellarator; mirror-type geometries) and introduces the specific properties of plasmas in these devices. Plasma confinement in tokamaks is treated in particular detail, in compliance with the importance of this field in fusion research. This includes a review of the ITER concept and of the rationale for the choice of ITER's parameters. In the second part, selected topics in fusion plasma physics (macroscopic instabilities; propagation of waves; kinetic effects such as energy transfer between waves and particles including microscopic instabilities as well as plasma heating and current drive; transport phenomena induced by turbulence) are presented systematically. While the emphasis is on displaying the essential physics, deeper theoretical analysis is also provided here. Every chapter is complemented by a few related problems, but only partial hints for their solution are given. A selection of

Enhancement of Tokamak Fusion Test Reactor performance by lithium conditioning

International Nuclear Information System (INIS)

Mansfield, D.K.; Hill, K.W.; Strachan, J.D.; Bell, M.G.; Scott, S.D.; Budny, R.; Marmar, E.S.; Snipes, J.A.; Terry, J.L.; Batha, S.; Bell, R.E.; Bitter, M.; Bush, C.E.; Chang, Z.; Darrow, D.S.; Ernst, D.; Fredrickson, E.; Grek, B.; Herrmann, H.W.; Janos, A.; Jassby, D.L.; Jobes, F.C.; Johnson, D.W.; Johnson, L.C.; Levinton, F.M.; Mikkelsen, D.R.; Mueller, D.; Owens, D.K.; Park, H.; Ramsey, A.T.; Roquemore, A.L.; Skinner, C.H.; Stevenson, T.; Stratton, B.C.; Synakowski, E.; Taylor, G.; von Halle, A.; von Goeler, S.; Wong, K.L.; Zweben, S.J.

1996-01-01

Wall conditioning in the Tokamak Fusion Test Reactor (TFTR) [K. M. McGuire et al., Phys. Plasmas 2, 2176 (1995)] by injection of lithium pellets into the plasma has resulted in large improvements in deuterium endash tritium fusion power production (up to 10.7 MW), the Lawson triple product (up to 10 21 m -3 s keV), and energy confinement time (up to 330 ms). The maximum plasma current for access to high-performance supershots has been increased from 1.9 to 2.7 MA, leading to stable operation at plasma stored energy values greater than 5 MJ. The amount of lithium on the limiter and the effectiveness of its action are maximized through (1) distributing the Li over the limiter surface by injection of four Li pellets into Ohmic plasmas of increasing major and minor radius, and (2) injection of four Li pellets into the Ohmic phase of supershot discharges before neutral-beam heating is begun. copyright 1996 American Institute of Physics

10th International Conference and School on Plasma Physics and Controlled Fusion. Book of Abstracts

International Nuclear Information System (INIS)

Anon

2004-01-01

About 240 abstracts by Ukrainian and foreign authors submitted to 10-th International Conference and School on Plasma Physics and Controlled fusion have been considered by Conference Program Committee members. All the abstracts have been divided into 8 groups: magnetic confinement systems: stellarators, tokamaks, alternative conceptions; ITER and Fusion reactor aspects; basic plasma physics; space plasma; plasma dynamics and plasma-wall interaction; plasma electronics; low temperature plasma and plasma technologies; plasma diagnostics

Demonstrating electromagnetic control of free-surface, liquid-metal flows relevant to fusion reactors

Science.gov (United States)

Hvasta, M. G.; Kolemen, E.; Fisher, A. E.; Ji, H.

2018-01-01

Plasma-facing components (PFC’s) made from solid materials may not be able to withstand the large heat and particle fluxes that will be produced within next-generation fusion reactors. To address the shortcomings of solid PFC’s, a variety of liquid-metal (LM) PFC concepts have been proposed. Many of the suggested LM-PFC designs rely on electromagnetic restraint (Lorentz force) to keep free-surface, liquid-metal flows adhered to the interior surfaces of a fusion reactor. However, there is very little, if any, experimental data demonstrating that free-surface, LM-PFC’s can actually be electromagnetically controlled. Therefore, in this study, electrical currents were injected into a free-surface liquid-metal that was flowing through a uniform magnetic field. The resultant Lorentz force generated within the liquid-metal affected the velocity and depth of the flow in a controllable manner that closely matched theoretical predictions. These results show the promise of electromagnetic control for LM-PFC’s and suggest that electromagnetic control could be further developed to adjust liquid-metal nozzle output, prevent splashing within a tokamak, and alter heat transfer properties for a wide-range of liquid-metal systems.

Fusion energy division computer systems network

International Nuclear Information System (INIS)

Hammons, C.E.

1980-12-01

The Fusion Energy Division of the Oak Ridge National Laboratory (ORNL) operated by Union Carbide Corporation Nuclear Division (UCC-ND) is primarily involved in the investigation of problems related to the use of controlled thermonuclear fusion as an energy source. The Fusion Energy Division supports investigations of experimental fusion devices and related fusion theory. This memo provides a brief overview of the computing environment in the Fusion Energy Division and the computing support provided to the experimental effort and theory research

BOOK REVIEW: Fundamentals of Plasma Physics and Controlled Fusion

Science.gov (United States)

Brambilla, Marco

1998-04-01

Professor Kenro Miyamoto, already well known for his textbook Plasma Physics for Nuclear Fusion (MIT Press, Cambridge, MA, 1976; revised edition 1989), has now published a new book entitled Fundamentals of Plasma Physics and Controlled Fusion (Iwanami Book Service Center, Tokyo, 1997). To a large extent, the new book is a somewhat shortened and well reorganized version of its predecessor. The style, concise and matter of fact, clearly shows the origin of the text in lectures given by the author to graduate students. As announced by the title, the book is divided into two parts: the first part (about 250 pages) is a general introduction to the physics of plasmas, while the second, somewhat shorter, part (about 150 pages), is devoted to a description of the most important experimental approaches to achieving controlled thermonuclear fusion. Even in the first part, moreover, the choice of subjects is consistently oriented towards the needs of fusion research. Thus, the introduction to the behaviour of charged particles (particle motion, collisions, etc.) and to the collective description of plasmas is quite short, although the reader will get a flavour of all the most important topics and will find a number of examples chosen for their relevance to fusion applications (only the presentation of the Vlasov equation, in the second section of Chapter 4, might be criticized as so concise as to be almost misleading, since the difference between microscopic and macroscopic fields is not even mentioned). Considerably more space is devoted to the magnetohydrodynamic (MHD) description of equilibrium and stability. This part includes the solution of the Grad-Shafranov equation for circular tokamaks, a brief discussion of Pfirsch-Schlüter, neoclassical and anomalous diffusion, and two relatively long chapters on the most important ideal and resistive MHD instabilities of toroidal plasmas; drift and ion temperature gradient driven instabilities are also briefly presented. The

LiWall Fusion - The New Concept of Magnetic Fusion

International Nuclear Information System (INIS)

Zakharov, L.E.

2011-01-01

Utilization of the outstanding abilities of a liquid lithium layer in pumping hydrogen isotopes leads to a new approach to magnetic fusion, called the LiWall Fusion. It relies on innovative plasma regimes with low edge density and high temperature. The approach combines fueling the plasma by neutral injection beams with the best possible elimination of outside neutral gas sources, which cools down the plasma edge. Prevention of cooling the plasma edge suppresses the dominant, temperature gradient related turbulence in the core. Such an approach is much more suitable for controlled fusion than the present practice, relying on high heating power for compensating essentially unlimited turbulent energy losses.

Study of the application of advanced control systems to fusion experiments and reactors. Final report

International Nuclear Information System (INIS)

1974-05-01

The work accomplished to date toward the formulation of an advanced control system concept for large-scale magnetically confined thermonuclear fusion devices is summarized. The work was concentrated in three major areas: (1) general control studies and identification of control issues, (2) exploration of possible direct interactions with AEC National Laboratories, and (3) identification of simulation requirements to support control studies. (U.S.)

Fusion reactor design studies

International Nuclear Information System (INIS)

Emmert, G.A.; Kulcinski, G.L.; Santarius, J.F.

1990-01-01

This report discusses the following topics on the ARIES tokamak: systems; plasma power balance; impurity control and fusion ash removal; fusion product ripple loss; energy conversion; reactor fueling; first wall design; shield design; reactor safety; and fuel cost and resources

Plasma Equilibrium Control in Nuclear Fusion Devices 2. Plasma Control in Magnetic Confinement Devices 2.1 Plasma Control in Tokamaks

Science.gov (United States)

Fukuda, Takeshi

The plasma control technique for use in large tokamak devices has made great developmental strides in the last decade, concomitantly with progress in the understanding of tokamak physics and in part facilitated by the substantial advancement in the computing environment. Equilibrium control procedures have thereby been established, and it has been pervasively recognized in recent years that the real-time feedback control of physical quantities is indispensable for the improvement and sustainment of plasma performance in a quasi-steady-state. Further development is presently undertaken to realize the “advanced plasma control” concept, where integrated fusion performance is achieved by the simultaneous feedback control of multiple physical quantities, combined with equilibrium control.

Coatings for fusion reactor environments

International Nuclear Information System (INIS)

Mattox, D.M.

1979-01-01

The internal surfaces of a tokamak fusion reactor control the impurity injection and gas recycling into the fusion plasma. Coating of internal surfaces may provide a desirable and possibly necessary design flexibility for achieving the temperatures, ion densities and containment times necessary for net energy production from fusion reactions to take place. In this paper the reactor environments seen by various componentare reviewed along with possible materials responses. Characteristics of coating-substrate systems, important to fusion applications, are delineated and the present status of coating development for fusion applications is reviewed. Coating development for fusion applications is just beginning and poses a unique and important challenge for materials development

Multi-rate sensor fusion-based adaptive discrete finite-time synergetic control for flexible-joint mechanical systems

International Nuclear Information System (INIS)

Xue Guang-Yue; Ren Xue-Mei; Xia Yuan-Qing

2013-01-01

This paper proposes an adaptive discrete finite-time synergetic control (ADFTSC) scheme based on a multi-rate sensor fusion estimator for flexible-joint mechanical systems in the presence of unmeasured states and dynamic uncertainties. Multi-rate sensors are employed to observe the system states which cannot be directly obtained by encoders due to the existence of joint flexibilities. By using an extended Kalman filter (EKF), the finite-time synergetic controller is designed based on a sensor fusion estimator which estimates states and parameters of the mechanical system with multi-rate measurements. The proposed controller can guarantee the finite-time convergence of tracking errors by the theoretical derivation. Simulation and experimental studies are included to validate the effectiveness of the proposed approach. (general)

Research programme on controlled thermonuclear fusion - Synthesis report 2008

International Nuclear Information System (INIS)

Werthmueller, A.

2009-06-01

Switzerland is associated to the International Thermonuclear Experimental Reactor (ITER) project carried out in the framework of the European Atomic Energy Community (EURATOM). The current stage includes on-site civil engineering works. The Variable Configuration Tokamak (TCV) of the 'Centre de Recherches en Physique des Plasmas' (CRPP) of the EPFL will remain an important recognized research facility until the start of the ITER operation foreseen in 2018. At the European level, the whole fusion research is coordinated and partly financed by the Joint Undertaking Fusion for Energy (JU F4E). The large flexibility of the TCV design and operation modus allow the creation and control of plasmas of various shapes, what is a very useful option to verify the results of numerical simulations. Besides, the hyper-frequency power density injected into the plasma is the highest ever recorded in the world. Research topics studied with the TCV include the stationary regimes in the tokamaks; a plasma current of more than 70 kA could be maintained, what represents an improvement by a factor of 3 to 4 of the confinement quality. For the first time in the world a configuration of the 'snowflake' type could be created and the power density on the wall of the vacuum chamber could be reduced accordingly. Numerical models allowed the analysis of turbulence and heat transport, of the magneto-hydrodynamic stability of the tokamaks and stellarators as well as the optimization of the magnetic confinement. Results concerning the so-called 'saw teeth' instability were experimentally confirmed on the Joint European Torus (JET). Theoretical researches were carried out on the fluctuations, turbulence and transport phenomena in the magnetized toric plasmas. At the Paul Scherrer Institute (PSI) the effect of the fast neutrons emitted by the fusion reactions on the walls of the fusion reactors was investigated. Irradiation simulations were carried out by means of the Swiss Spallation Neutron Source

Understanding fuel magnetization and mix using secondary nuclear reactions in magneto-inertial fusion.

Science.gov (United States)

Schmit, P F; Knapp, P F; Hansen, S B; Gomez, M R; Hahn, K D; Sinars, D B; Peterson, K J; Slutz, S A; Sefkow, A B; Awe, T J; Harding, E; Jennings, C A; Chandler, G A; Cooper, G W; Cuneo, M E; Geissel, M; Harvey-Thompson, A J; Herrmann, M C; Hess, M H; Johns, O; Lamppa, D C; Martin, M R; McBride, R D; Porter, J L; Robertson, G K; Rochau, G A; Rovang, D C; Ruiz, C L; Savage, M E; Smith, I C; Stygar, W A; Vesey, R A

2014-10-10

Magnetizing the fuel in inertial confinement fusion relaxes ignition requirements by reducing thermal conductivity and changing the physics of burn product confinement. Diagnosing the level of fuel magnetization during burn is critical to understanding target performance in magneto-inertial fusion (MIF) implosions. In pure deuterium fusion plasma, 1.01 MeV tritons are emitted during deuterium-deuterium fusion and can undergo secondary deuterium-tritium reactions before exiting the fuel. Increasing the fuel magnetization elongates the path lengths through the fuel of some of the tritons, enhancing their probability of reaction. Based on this feature, a method to diagnose fuel magnetization using the ratio of overall deuterium-tritium to deuterium-deuterium neutron yields is developed. Analysis of anisotropies in the secondary neutron energy spectra further constrain the measurement. Secondary reactions also are shown to provide an upper bound for the volumetric fuel-pusher mix in MIF. The analysis is applied to recent MIF experiments [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)] on the Z Pulsed Power Facility, indicating that significant magnetic confinement of charged burn products was achieved and suggesting a relatively low-mix environment. Both of these are essential features of future ignition-scale MIF designs.

A novel method for trace tritium transport studies

International Nuclear Information System (INIS)

Bonheure, Georges; Mlynar, Jan; Murari, A.; Giroud, C.; Popovichev, S.; Belo, P.; Bertalot, L.

2009-01-01

A new method combining a free-form solution for the neutron emissivity and the ratio method (Bonheure et al 2006 Nucl. Fusion 46 725-40) is applied to the investigation of tritium particle transport in JET plasmas. The 2D neutron emissivity is calculated using the minimum Fisher regularization method (MFR) (Anton et al 1996 Plasma Phys. Control. Fusion 38 1849, Mlynar et al 2003 Plasma Phys. Control. Fusion 45 169). This method is being developed and studied alongside other methods at JET. The 2D neutron emissivity was significantly improved compared with the first MFR results by constraining the emissivity along the magnetic flux surfaces. 1D profiles suitable for transport analysis are then obtained by subsequent poloidal integration. In methods on which previous JET publications are based (Stork et al 2005 Nucl. Fusion 45 S181, JET Team (prepared by Zastrow) 1999 Nucl. Fusion 39 1891, Zastrow et al 2004 Plasma Phys. Control. Fusion 46 B255, Adams et al 1993 Nucl. Instrum. Methods A 329 277, Jarvis et al 1997 Fusion Eng. Des. 34-35 59, Jarvis et al 1994 Plasma Phys. Control. Fusion 36 219), the 14.07 MeV D-T neutron line integrals measurements were simulated and the transport coefficients varied until good fits were obtained. In this novel approach, direct knowledge of tritium concentration or the fuel ratio n T /n D is obtained using all available neutron profile information, e.g both 2.45 MeV D-D neutron profiles and 14.07 MeV D-T neutron profiles (Bonheure et al 2006 Nucl.Fusion 46 725-40). Tritium particle transport coefficients are then determined using a linear regression from the dynamic response of the tritium concentration n T /n D profile. The temporal and spatial evolution of tritium particle concentration was studied for a set of JET discharges with tritium gas puffs from the JET trace tritium experiments. Local tritium transport coefficients were derived from the particle flux equation Γ = -D∇n T + Vn T , where D is the particle diffusivity and V

Introduction to controlled thermonuclear fusion

International Nuclear Information System (INIS)

Assis, A.S. de; Rapozo, C.C.

1988-07-01

During many centuries the origin of the enormous power output of the sun remained as a mistery. However, in this century, the physicists have discovered that stars get their energy from the fusion of light nuclei (such as deuterons and tritons), and the Einstein's equation, AE = (Am)c 2 , was the way to explain this physical process. (author)

Introduction to Nuclear Fusion Power and the Design of Fusion Reactors. An Issue-Oriented Module.

Science.gov (United States)

Fillo, J. A.

This three-part module focuses on the principles of nuclear fusion and on the likely nature and components of a controlled-fusion power reactor. The physical conditions for a net energy release from fusion and two approaches (magnetic and inertial confinement) which are being developed to achieve this goal are described. Safety issues associated…

Reaching to a featured formula to deduce the energy of the heaviest particles producing from the controlled thermonuclear fusion reactions

Science.gov (United States)

Majeed, Raad H.; Oudah, Osamah N.

2018-05-01

Thermonuclear fusion reaction plays an important role in developing and construction any power plant system. Studying the physical behavior for the possible mechanism governed energies released by the fusion products to precise understanding the related kinematics. In this work a theoretical formula controlled the general applied thermonuclear fusion reactions is achieved to calculating the fusion products energy depending upon the reactants physical properties and therefore, one can calculate other parameters governed a given reaction. By using this formula, the energy spectrum of 4He produced from T-3He fusion reaction has been sketched with respect to reaction angle and incident energy ranged from (0.08-0.6) MeV.

Rotamak offers new twist in the search for fusion

International Nuclear Information System (INIS)

Hoffman, A.

1998-01-01

Nuclear fusion - the energy source of the stars - could one day become an unlimited source of energy on Earth. But to achieve fusion, a hydrogen plasma must be heated to temperatures of 100 million degrees and confined at high enough densities for thermonuclear reactions to occur. This is usually achieved on Earth by confining the plasma in a toroidal (doughnut-shaped) machine known as a tokamak. However, tokamaks are large and complex machines, and next-generation devices are expected to cost around $10bn. Although such a machine has already been designed by an international collaboration, it is proving extremely difficult to secure funding to build it, and the search is on for simpler and cheaper alternatives. One possibility, which has been developed in Australia over the last 20 years, is a compact machine known as a rotamak. Recent experiments by Ieuan Jones and colleagues at Flinders University in Adelaide have demonstrated a new mode of operation for this type of device, which they call a rotamak-ST (where ST stands for spherical tokamak). In the process, they achieved the best-ever performance for a rotamak (I R Jones et al. 1998 Phys. Rev. Lett. 81 2072). The results are so encouraging that larger facilities in the UK and the US are now planning similar experiments. In this article the author describes the latest fusion research. (UK)

LLL magnetic fusion research: the first 25 years

International Nuclear Information System (INIS)

Post, R.F.

1978-01-01

From its inception, the Laboratory has supported research directed at tapping controlled fusion. Our magnetic fusion energy program--now one of the major elements of the national fusion energy research effort--dates back to the Laboratory's founding in 1952. This article reviews the program's beginnings, progress, and present status in terms of its ultimate goal: to demonstrate a practical and economical means of generating power from controlled fusion reactions

The use of industrial type control and monitoring components for a large fusion experiment

International Nuclear Information System (INIS)

Hemming, O.N.; Manduchi, G.; Luchetta, A.; Schmidt, V.; Vitturi, S.

1994-01-01

RFX is one of the large nuclear fusion experiments within the framework of the co-ordinated nuclear fusion research programme of the European Community. During the control system design phase in 1986, the increase in power and flexibility of industrial type programmable controllers lead to the decision for a complete physical split of control, monitoring and data acquisition functions according to speed requirements, allowing the exploitation of the relative advantages of both CAMAC and programmable controllers. The 'slow' control and monitoring functions (for about 4000 digital and 200 analog I/O signals with scanning times of similar 1 second) have been implemented using a series of networked industrial PLCs and personal computers. This has allowed us to choose from a wide range of off-the-shelf hardware and software components for the plant interface and to utilize specialized expertise from the industrial field for the application software implementation. The paper gives the expectations and results gained from this design choice and how it has influenced the decisions for the evolution of the system over the next few years with the utilization of new industrial hardware components. Details are also given regarding the system integration (via the Ethernet network) with the VAX-based CAMAC frontend fast control and data-acquisition system. ((orig.))

Introduction to plasma physics and controlled fusion

CERN Document Server

Chen, Francis F

1984-01-01

This complete introduction to plasma physics and controlled fusion by one of the pioneering scientists in this expanding field offers both a simple and intuitive discussion of the basic concepts of this subject and an insight into the challenging problems of current research. In a wholly lucid manner the work covers single-particle motions, fluid equations for plasmas, wave motions, diffusion and resistivity, Landau damping, plasma instabilities and nonlinear problems. For students, this outstanding text offers a painless introduction to this important field; for teachers, a large collection of problems; and for researchers, a concise review of the fundamentals as well as original treatments of a number of topics never before explained so clearly. This revised edition contains new material on kinetic effects, including Bernstein waves and the plasma dispersion function, and on nonlinear wave equations and solitons.

Fusion, magnetic confinement

International Nuclear Information System (INIS)

Berk, H.L.

1992-01-01

An overview is presented of the principles of magnetic confinement of plasmas for the purpose of achieving controlled fusion conditions. Sec. 1 discusses the different nuclear fusion reactions which can be exploited in prospective fusion reactors and explains why special technologies need to be developed for the supply of tritium or 3 He, the probable fuels. In Sec. 2 the Lawson condition, a criterion that is a measure of the quality of confinement relative to achieving fusion conditions, is explained. In Sec. 3 fluid equations are used to describe plasma confinement. Specific confinement configurations are considered. In Sec. 4 the orbits of particle sin magneti and electric fields are discussed. In Sec. 5 stability considerations are discussed. It is noted that confinement systems usually need to satisfy stability constraints imposed by ideal magnetohydrodynamic (MHD) theory. The paper culminates with a summary of experimental progress in magnetic confinement. Present experiments in tokamaks have reached the point that the conditions necessary to achieve fusion are being satisfied

Fusion spectroscopy

International Nuclear Information System (INIS)

Peacock, N.J.

1995-09-01

This article traces developments in the spectroscopy of high temperature laboratory plasma used in controlled fusion research from the early 1960's until the present. These three and a half decades have witnessed many orders of magnitude increase in accessible plasma parameters such as density and temperature as well as particle and energy confinement timescales. Driven by the need to interpret the radiation in terms of the local plasma parameters, the thrust of fusion spectroscopy has been to develop our understanding of (i) the atomic structure of highly ionised atoms, usually of impurities in the hydrogen isotope fuel; (ii) the atomic collision rates and their incorporation into ionization structure and emissivity models that take into account plasma phenomena like plasma-wall interactions, particle transport and radiation patterns; (iii) the diagnostic applications of spectroscopy aided by increasingly sophisticated characterisation of the electron fluid. These topics are discussed in relation to toroidal magnetically confined plasmas, particularly the Tokamak which appears to be the most promising approach to controlled fusion to date. (author)

Tritium control and capture in salt-cooled fission and fusion reactors: Status, challenges, and path forward

International Nuclear Information System (INIS)

Forsberg, Charles W.; Lam, Stephen; Carpenter, David M.; Whyte, Dennis G.; Scarlat, Raluca

2017-01-01

Three advanced nuclear power systems use liquid salt coolants that generate tritium and thus face the common challenges of containing and capturing tritium to prevent its release to the environment. The Fluoride-salt-cooled High-temperature Reactor (FHR) uses clean fluoride salt coolants and the same graphite-matrix coated-particle fuel as high-temperature gas-cooled reactors. Molten salt reactors (MSRs) dissolve the fuel in a fluoride or chloride salt with release of fission product tritium into the salt. In most FHR and MSR systems, the base-line salts contain lithium where isotopically separated "7Li is proposed to minimize tritium production from neutron interactions with the salt. The Chinese Academy of Science plans to start operation of a 2-MWt molten salt test reactor by 2020. For high-magnetic-field fusion machines, the use of lithium enriched in "6Li is proposed to maximize tritium generation the fuel for a fusion machine. Advances in superconductors that enable higher power densities may require the use of molten lithium salts for fusion blankets and as coolants. Recent technical advances in these three reactor classes have resulted in increased government and private interest and the beginning of a coordinated effort to address the tritium control challenges in 700 °C liquid salt systems. We describe characteristics of salt-cooled fission and fusion machines, the basis for growing interest in these technologies, tritium generation in molten salts, the environment for tritium capture, models for high-temperature tritium transport in salt systems, alternative strategies for tritium control, and ongoing experimental work. Several methods to control tritium appear viable. Finally, limited experimental data is the primary constraint for designing efficient cost-effective methods of tritium control.

Ignition on the National Ignition Facility: a path towards inertial fusion energy

International Nuclear Information System (INIS)

Moses, Edward I.

2009-01-01

the world's attention on the possibility of an ICF energy option. NIF experiments to demonstrate ignition and gain will use central-hot-spot (CHS) ignition, where a spherical fuel capsule is simultaneously compressed and ignited. The scientific basis for CHS has been intensively developed (Lindl 1998 Inertial Confinement Fusion: the Quest for Ignition and Energy Gain Using Indirect Drive (New York: American Institute of Physics)) and has a high probability of success. Achieving ignition with CHS will open the door for other advanced concepts, such as the use of high-yield pulses of visible wavelength rather than ultraviolet and fast ignition concepts (Tabak et al 1994 Phys. Plasmas 1 1626-34, Tabak et al 2005 Phys. Plasmas 12 057305). Moreover, NIF will have important scientific applications in such diverse fields as astrophysics, nuclear physics and materials science. This paper summarizes the design, performance and status of NIF, experimental plans for NIC, and will present laser inertial confinement fusion-fission energy (LIFE) as a path to achieve carbon-free sustainable energy.

Ignition on the National Ignition Facility: a path towards inertial fusion energy

Science.gov (United States)

Moses, Edward I.

2009-10-01

the world's attention on the possibility of an ICF energy option. NIF experiments to demonstrate ignition and gain will use central-hot-spot (CHS) ignition, where a spherical fuel capsule is simultaneously compressed and ignited. The scientific basis for CHS has been intensively developed (Lindl 1998 Inertial Confinement Fusion: the Quest for Ignition and Energy Gain Using Indirect Drive (New York: American Institute of Physics)) and has a high probability of success. Achieving ignition with CHS will open the door for other advanced concepts, such as the use of high-yield pulses of visible wavelength rather than ultraviolet and fast ignition concepts (Tabak et al 1994 Phys. Plasmas 1 1626-34, Tabak et al 2005 Phys. Plasmas 12 057305). Moreover, NIF will have important scientific applications in such diverse fields as astrophysics, nuclear physics and materials science. This paper summarizes the design, performance and status of NIF, experimental plans for NIC, and will present laser inertial confinement fusion-fission energy (LIFE) as a path to achieve carbon-free sustainable energy.

‘PhysTrack’: a Matlab based environment for video tracking of kinematics in the physics laboratory

Science.gov (United States)

Umar Hassan, Muhammad; Sabieh Anwar, Muhammad

2017-07-01

In the past two decades, several computer software tools have been developed to investigate the motion of moving bodies in physics laboratories. In this article we report a Matlab based video tracking library, PhysTrack, primarily designed to investigate kinematics. We compare PhysTrack with other commonly available video tracking tools and outline its salient features. The general methodology of the whole video tracking process is described with a step by step explanation of several functionalities. Furthermore, results of some real physics experiments are also provided to demonstrate the working of the automated video tracking, data extraction, data analysis and presentation tools that come with this development environment. We believe that PhysTrack will be valuable for the large community of physics teachers and students already employing Matlab.

Contributions to the 7th International Conference on plasma surface interactions in controlled fusion devices

International Nuclear Information System (INIS)

1986-01-01

The report contains three papers presented in the 7th International Conference on plasma surface interactions in controlled fusion devices held in Princeton (USA) 5-9 May 1986, all referred to the FT Tokamak

Research programme on controlled thermonuclear fusion. Synthesis report 2011; Programme de recherche Fusion thermonucleaire controlee. Rapport de synthese 2011

Energy Technology Data Exchange (ETDEWEB)

Vaucher, C. [Secretariat d' Etat a l' education et a la recherche, Berne (Switzerland); Tran, M. Q.; Villard, L. [Swiss Federal Institute of Technology (EPFL), Lausanne (Switzerland); Marot, L. [University of Basel, Basel (Switzerland)

2012-07-01

Since 1978, research on thermonuclear fusion in Switzerland is closely related to the research programme of the European Atomic Energy Community (EURATOM). The Swiss projects tackle aspects of plasma physics and fusion technology. Switzerland participates to the construction and operation of the Joint European Torus (JET), which started operation again in 2011. The International Thermonuclear Experimental Reactor (ITER) is the last step before DEMO, a prototype fusion reactor able to deliver electricity and demonstrate the economic viability of fusion energy. The 'Centre de Recherches en Physique des Plasmas' (CRPP) of the EPFL went on with its participation to the scientific and technological programme of EURATOM. Researches are carried out essentially on 2 sites: (i) at EPFL, where topics dealt with include the physics of magnetic confinement studied using the Variable Configuration Tokamak (TCV), the basic experiment TORPEX, theory and numerical modelling, and the technology of plasma heating and current generation by hyper-frequency waves; (ii) at the Paul Scherrer Institute (PSI), where activities are devoted to superconductivity and structure materials. Thanks to the large flexibility of the TCV design and operation modus, plasmas of different shapes can be created and controlled, what is a very useful option to verify numerical simulation results. Besides, the injection of millimetre waves allows directing the injected power according to specific profiles. In the TCV it could be demonstrated for the first time that the injection of Electronic Cyclotronic Heating (ECH) waves is able to double the frequency of so-called 'Edge Localized Modes' (ELM), reducing by a factor of 2 the energy expelled by each ELM. In particular, it was possible to considerably reduce the statistical dispersion of the repetition frequency of ELM, and to avoid the appearance of gigantic ELM that are particularly harmful for reactor operation. The effect of plasma

Plasma physics for controlled fusion

International Nuclear Information System (INIS)

Miyamoto, K.

2010-01-01

The primary objective of this lecture note is to present the theories and experiments of plasma physics for recent activities of controlled fusion research for graduate and senior undergraduate students. Chapters 1-6 describe the basic knowledge of plasma and magnetohydrodynamics (MHD). MHD instabilities limit the beta ratio (ratio of plasma pressure to magnetic pressure) of confined plasma. Chapters 7-9 provide the kinetic theory of hot plasma and discuss the wave heating and non-inductive current drive. The dispersion relation derived by the kinetic theory are used to discuss plasma waves and perturbed modes. Landau damping is the essential mechanism of plasma heating and the stabilization of perturbation. Landau inverse damping brings the amplification of waves and the destabilization of perturbed modes. Chapter 10 explains the plasma transport due to turbulence, which is the most important and challenging subject for plasma confinement. Theories and simulations including subject of zonal flow are introduced. Chapters 11, 12 and 13 describe the recent activities of tokamak including ITER as well as spherical tokamak, reversed field pinch (RFP) and stellarator including quasi-symmetric configurations. Emphasis has been given to tokamak research since it made the most remarkable progress and the construction phase of 'International Tokamak Experimental Reactor' called ITER has already started. (author)

50 years of controlled nuclear fusion in the European Union

International Nuclear Information System (INIS)

Vandenplas, P.; Wolf, G.H.

2008-01-01

The author presents the history of fusion energy since its official birth in 1955 during the first conference on the peaceful uses of atomic energy to the expectations put on the ITER project. Nuclear fusion became a major component of the newly created European Atomic Energy Community (EURATOM). The milestones that were: magnetic mirror machines, pinch versions, stellarators and tokamaks are examined. The construction of the first fusion machines were decisive and gave fusion energy enough momentum to overcome greater and greater technological difficulties. At the scale of the world, major machines that were built like TFTR, Princeton (1974), JET, Culham (1977) or JT60, Tokai (1977), appear like a scientific and necessary strategy towards the demonstration reactor. The ITER project is detailed

Electrostatic-Dipole (ED) Fusion Confinement Studies

Science.gov (United States)

Miley, George H.; Shrestha, Prajakti J.; Yang, Yang; Thomas, Robert

2004-11-01

The Electrostatic-Dipole (ED) concept significantly differs from a "pure" dipole confinement device [1] in that the charged particles are preferentially confined to the high-pressure region interior of the dipole coil by the assistance of a surrounding spherical electrostatic grid. In present ED experiments, a current carrying coil is embedded inside the grid of an IEC such as to produce a magnetic dipole field. Charged particles are injected axisymmetrically from an ion gun (or duo-plasmatron) into the center of the ED confinement grid/dipole ring where they oscillate along the magnetic field lines and pass the peak field region at the center of the dipole region. As particles begin accelerating away from the center region towards the outer electrostatic grid region, they encounter a strong electrostatic potential (order of 10's of kilovolts) retarding force. The particles then decelerate, reverse direction and re-enter the dipole field region where again magnetic confinement dominates. This process continues, emulating a complex harmonic oscillator motion. The resulting pressure profile averaged over the field curvature offers good plasma stability in the ED configuration. The basic concept and results from preliminary experiments will be described. [1] M.E. Mauel, et al. "Dipole Equilibrium and Stability," 18th IAEA Conference of Plasma Phys. and Control. Nuclear Fusion, Varenna, Italy 2000, IAEA-F1-CN-70/TH

Comment on “Theoretical analysis of high-field transport in graphene on a substrate” [J. Appl. Phys. 116, 034507 (2014)

International Nuclear Information System (INIS)

Tan, Michael L. P.; Arora, Vijay K.

2014-01-01

In a recent article, Serov et al. [J. Appl. Phys. 116, 034507 (2014)] claim: “This study represents the first time that the high-field behavior in graphene on a substrate was investigated taking into account intrinsic graphene properties,” ignoring the most recent anisotropic distribution function [V. K. Arora et al., J. Appl. Phys. 112, 114330 (2012)] also published in J. Appl. Phys., targeting the same experimental data [V. E. Dorgan et al., Appl. Phys. Lett. 97, 082112 (2010)]. The claim of Serov et al. of being first is refuted and many shortcomings of the hydrodynamic model for a highly quantum and degenerate graphene nanolayer are pointed out

Solar fusion cross sections II: the pp chain and CNO cycles

Energy Technology Data Exchange (ETDEWEB)

Adelberger, E G; Bemmerer, D; Bertulani, C A; Chen, J -W; Costantini, H; Couder, M; Cyburt, R; Davids, B; Freedman, S J; Gai, M; Garcia, A; Gazit, D; Gialanella, L; Greife, U; Hass, M; Heeger, K; Haxton, W C; Imbriani, G; Itahashi, T; Junghans, A; Kubodera, K; Langanke, K; Leitner, D; Leitner, M; Marcucci, L E; Motobayashi, T; Mukhamedzhanov, A; Nollett, Kenneth M; Nunes, F M; Park, T -S; Parker, P D; Prati, P; Ramsey-Musolf, M J; Hamish Robertson, R G; Schiavilla, R; Simpson, E C; Snover, K A; Spitaleri, C; Strieder, F; Suemmerer, K; Trautvetter, R E; Tribble, R E; Typel, S; Uberseder, E; Vetter, P; Wiescher, M

2011-04-01

The available data on nuclear fusion cross sections important to energy generation in the Sun and other hydrogen-burning stars and to solar neutrino production are summarized and critically evaluated. Recommended values and uncertainties are provided for key cross sections, and a recommended spectrum is given for 8B solar neutrinos. Opportunities for further increasing the precision of key rates are also discussed, including new facilities, new experimental techniques, and improvements in theory. This review, which summarizes the conclusions of a workshop held at the Institute for Nuclear Theory, Seattle, in January 2009, is intended as a 10-year update and supplement to 1998, Rev. Mod. Phys. 70, 1265.

Health physics in fusion reactor design

International Nuclear Information System (INIS)

Wong, K.Y.; Dinner, P.J.

1984-06-01

Experience in the control of tritium exposures to workers and the public gained through the design and operation of Ontario Hydro's nuclear stations has been applied to fusion projects and to design studies on emerging fusion reactor concepts. Ontario Hydro performance in occupational tritium exposure control and environmental impact is reviewed. Application of tritium control technologies and dose management methodology during facility design is highlighted

History and status of magnetic fusion research; Evolution et statut des recherches sur la fusion controlee

Energy Technology Data Exchange (ETDEWEB)

Jacquinot, J. [CEA Saclay, Cabinet du Haut Commissaire, 91 - Gif-sur-Yvette (France)

2008-02-15

Ever since the understanding of the basic process which powers the stars has been elucidated, humanity has been dreaming to master controlled fusion for peaceful purposes. Controlled fusion in a steady state regime must use magnetic confinement of a gas (plasma) heated up to 150 millions degrees. Physics and technology involved in such a state are extremely complex and went through many up and down phases. Nevertheless, the overall progress has been spectacular and a significant amount of energy could be produced in a well controlled manner. On this basis, an international organisation of unprecedented magnitude involving 34 countries has started working in Cadarache for the construction of the ITER project. It aims at the scientific demonstration of controlled fusion at the level of 500 MW and a power gain of 10. (author)

American research programs on controlled thermonuclear fusion

International Nuclear Information System (INIS)

Anon.

1978-01-01

At a time when the site of the European JET project has been decided, this study proposes to highlight the American effort in this field over the last five years. The Federal Civil Research and Development budget assigned to Energy has been multiplied by 6.3 and inside this budget the portion allocated to fusion has been multiplied by a factor of 6, in value. Two avenues have been explored; magnetic confinement and inertial confinement but one reaction only has been considered, namely D + T fusion. In magnetic confinement, the first operational reactor is being contemplated for around the year 2012. Three technologies have been explored in inertial confinement: by laser beams, electron beams and ion beams [fr

Japanese fusion research

International Nuclear Information System (INIS)

Uchida, T.

1987-01-01

The Japan experience during thirty years in nuclear fusion research is reported, after attending the 1st Geneva Conference in 1955, Osaka University, immedeately began linear pinch study using capacitor bank discharge. Subsequently to his trial several groups were organized to ward fusion R and D at universities in Tokyo, Nagoya, Kyoto, Sendai and son on. Based upon the recommendation of Japan Science Council, Institut of Plasma Physics (IPP) was established at Nagoya University in 1961 When the 1st International Conference on Plasma Physics and Controlled Nuclear Fusion Research was held in Saltzburg. The gloomy Bohm barrier had stood in front of many of experiments at that time. (author) [pt

Peaceful Uses of Fusion

Science.gov (United States)

Teller, E.

1958-07-03

Applications of thermonuclear energy for peaceful and constructive purposes are surveyed. Developments and problems in the release and control of fusion energy are reviewed. It is pointed out that the future of thermonuclear power reactors will depend upon the construction of a machine that produces more electric energy than it consumes. The fuel for thermonuclear reactors is cheap and practically inexhaustible. Thermonuclear reactors produce less dangerous radioactive materials than fission reactors and, when once brought under control, are not as likely to be subject to dangerous excursions. The interaction of the hot plasma with magnetic fields opens the way for the direct production of electricity. It is possible that explosive fusion energy released underground may be harnessed for the production of electricity before the same feat is accomplished in controlled fusion processes. Applications of underground detonations of fission devices in mining and for the enhancement of oil flow in large low-specific-yield formations are also suggested.

Evaluation of efficacy of a new hybrid fusion device: a randomized, two-centre controlled trial.

Science.gov (United States)

Siewe, Jan; Bredow, Jan; Oppermann, Johannes; Koy, Timmo; Delank, Stefan; Knoell, Peter; Eysel, Peer; Sobottke, Rolf; Zarghooni, Kourosh; Röllinghoff, Marc

2014-09-05

The 360° fusion of lumbar segments is a common and well-researched therapy to treat various diseases of the spine. But it changes the biomechanics of the spine and may cause adjacent segment disease (ASD). Among the many techniques developed to avoid this complication, one appears promising. It combines a rigid fusion with a flexible pedicle screw system (hybrid instrumentation, "topping off"). However, its clinical significance is still uncertain due to the lack of conclusive data. The study is a randomized, therapy-controlled, two-centre trial conducted in a clinical setting at two university hospitals. If they meet the criteria, outpatients presenting with degenerative disc disease, facet joint arthrosis or spondylolisthesis will be included in the study and randomized into two groups: a control group undergoing conventional fusion surgery (PLIF - posterior lumbar intervertebral fusion), and an intervention group undergoing fusion surgery using a new flexible pedicle screw system (PLIF + "topping off"), which was brought on the market in 2013. Follow-up examination will take place immediately after surgery, after 6 weeks and after 6, 12, 24 and 36 months. An ongoing assessment will be performed every year.Outcome measurements will include quality of life and pain assessments using validated questionnaires (ODI - Ostwestry Disability Index, SF-36™ - Short Form Health Survey 36, COMI - Core Outcome Measure Index). In addition, clinical and radiologic ASD, sagittal balance parameters and duration of work disability will be assessed. Inpatient and 6-month mortality, surgery-related data (e.g., intraoperative complications, blood loss, length of incision, surgical duration), postoperative complications (e.g. implant failure), adverse events, and serious adverse events will be monitored and documented throughout the study. New hybrid "topping off" systems might improve the outcome of lumbar spine fusion. But to date, there is a serious lack of and a great need

Coatings for laser fusion

International Nuclear Information System (INIS)

Lowdermilk, W.H.

1981-01-01

Optical coatings are used in lasers systems for fusion research to control beam propagation and reduce surface reflection losses. The performance of coatings is important in the design, reliability, energy output, and cost of the laser systems. Significant developments in coating technology are required for future lasers for fusion research and eventual power reactors

Plasma physics and controlled nuclear fusion

International Nuclear Information System (INIS)

Sato, Tetsuya

1993-05-01

The report contains the proceedings of a conference on plasma physics. A fraction of topics included MHD instabilities, magnetic confinement and plasma heating in the field of fusion plasmas, in 8 papers falling in the INIS scope have been abstracted and indexed for the INIS database. (K.A.)

Application of controlled thermonuclear reactor fusion energy for food production

International Nuclear Information System (INIS)

Dang, V.D.; Steinberg, M.

1975-06-01

Food and energy shortages in many parts of the world in the past two years raise an immediate need for the evaluation of energy input in food production. The present paper investigates systematically (1) the energy requirement for food production, and (2) the provision of controlled thermonuclear fusion energy for major energy intensive sectors of food manufacturing. Among all the items of energy input to the ''food industry,'' fertilizers, water for irrigation, food processing industries, such as beet sugar refinery and dough making and single cell protein manufacturing, have been chosen for study in detail. A controlled thermonuclear power reactor was used to provide electrical and thermal energy for all these processes. Conceptual design of the application of controlled thermonuclear power, water and air for methanol and ammonia synthesis and single cell protein production is presented. Economic analysis shows that these processes can be competitive. (auth)

The IGNITEX fusion project

International Nuclear Information System (INIS)

Carrera, R.

1987-01-01

The author discusses the recently proposed fusion ignition experiment, IGNITEX. He emphasizes the basic ideas of this concept rather than the specific details of the physics and engineering aspects of the experiment. This concept is a good example of the importance of maintaining an adequate balance between the basic scientific progress in fusion physics and the new technologies that are becoming available in order to make fusion work. The objective of the IGNITEX project is to produce and control ignited plasmas for scientific study in the simplest and least expensive way possible. Being able to study this not-yet-produced regime of plasma operation is essential to fusion research. Two years after the fission nuclear reaction was discovered, a non-self-sustained fission reaction was produced in a laboratory, and in one more year a self-sustained reaction was achieved at the University of Chicago. However, after almost forty years of fusion research, a self-sustained fusion reaction has yet not been produced in a laboratory experiment. This fact indicates the greater difficulty of the fusion experiment. Because of the difficulty involved in the production of a self-sustained fusion reaction, it is necessary to propose such an experiment with maximum ignition margins, maximum simplicity, and minimum financial risk

A semi-analytic model of magnetized liner inertial fusion

Energy Technology Data Exchange (ETDEWEB)

McBride, Ryan D.; Slutz, Stephen A. [Sandia National Laboratories, Albuquerque, New Mexico 87185 (United States)

2015-05-15

Presented is a semi-analytic model of magnetized liner inertial fusion (MagLIF). This model accounts for several key aspects of MagLIF, including: (1) preheat of the fuel (optionally via laser absorption); (2) pulsed-power-driven liner implosion; (3) liner compressibility with an analytic equation of state, artificial viscosity, internal magnetic pressure, and ohmic heating; (4) adiabatic compression and heating of the fuel; (5) radiative losses and fuel opacity; (6) magnetic flux compression with Nernst thermoelectric losses; (7) magnetized electron and ion thermal conduction losses; (8) end losses; (9) enhanced losses due to prescribed dopant concentrations and contaminant mix; (10) deuterium-deuterium and deuterium-tritium primary fusion reactions for arbitrary deuterium to tritium fuel ratios; and (11) magnetized α-particle fuel heating. We show that this simplified model, with its transparent and accessible physics, can be used to reproduce the general 1D behavior presented throughout the original MagLIF paper [S. A. Slutz et al., Phys. Plasmas 17, 056303 (2010)]. We also discuss some important physics insights gained as a result of developing this model, such as the dependence of radiative loss rates on the radial fraction of the fuel that is preheated.

Fusion rings and fusion ideals

DEFF Research Database (Denmark)

Andersen, Troels Bak

by the so-called fusion ideals. The fusion rings of Wess-Zumino-Witten models have been widely studied and are well understood in terms of precise combinatorial descriptions and explicit generating sets of the fusion ideals. They also appear in another, more general, setting via tilting modules for quantum......This dissertation investigates fusion rings, which are Grothendieck groups of rigid, monoidal, semisimple, abelian categories. Special interest is in rational fusion rings, i.e., fusion rings which admit a finite basis, for as commutative rings they may be presented as quotients of polynomial rings...

An electrolytic route to fusion?

International Nuclear Information System (INIS)

Anon.

1992-01-01

A patent has been granted by the Swedish Patent Authority for a new process to initiate and control energy generation through fusion reactions of hydrogen. According to the patent-holder, the Swedish company AB Technology Development, the fusion power process could be available for commercial applications within 4-5 years if laboratory and pilot plant tests prove successful. The new process employs a high voltage discharge in heavy water to create conditions under which, according to the patent holder, a high probability of fusion is achieved without the extraordinary high temperatures required in a conventional fusion reactor. (author)

Multilayer mirror based monitors for impurity controls in large fusion reactor type devices

International Nuclear Information System (INIS)

Regan, S.P.; May, M.J.; Soukhanovskii, V.; Finkenthal, M.; Moos, H.W.

1995-01-01

Multilayer Mirror (MLM) based monitors are compact, high throughput diagnostics capable of extracting XUV emissions (the wavelength range including the soft-x-ray and the extreme ultraviolet, 10 angstrom to 304 angstrom) of impurities from the harsh environment of large fusion reactor type devices. For several years the Plasma Spectroscopy Group at Johns Hopkins University has investigated the application of MLM based XUV spectroscopic diagnostics for magnetically confined fusion plasmas. MLM based monitors have been constructed for and extensively used on DIII-D, Alcator C-mod, TEXT, Phaedrus-T, and CDX-U tokamaks to study the impurity behavior of elements ranging from He to Mo. On ITER MLM based devices would be used to monitor the spectral line emissions from Li I-like to F I-like charge states of Fe, Cr, and Ni, as well as extractors for the bands of emissions from high Z elements such as Mo or W for impurity controls of the fusion plasma. In addition to monitoring the impurity emissions from the main plasma, MLM based devices can also be adapted for radiation measurements of low Z elements in the divertor. The concepts and designs of these MLM based monitors for impurity controls in ITER will be presented. The results of neutron irradiation experiments of the MLMs performed in the Los Alamos Spallation Radiation Effects Facility (LASREF) at the Los Alamos National Laboratory will also be discussed. These preliminary neutron exposure studies show that the dispersive and reflective qualities of the MLMs were not affected in a significant manner

Equivalence of two independent calculations of the higher order guiding center Lagrangian

International Nuclear Information System (INIS)

Parra, F. I.; Calvo, I.; Burby, J. W.; Squire, J.; Qin, H.

2014-01-01

The difference between the guiding center phase-space Lagrangians derived in J. W. Burby et al. [Phys. Plasmas 20, 072105 (2013)] and F. I. Parra and I. Calvo [Plasma Phys. Controlled Fusion 53, 045001 (2011)] is due to a different definition of the guiding center coordinates. In this brief communication, the difference between the guiding center coordinates is calculated explicitly

Fusion Plasma Theory project summaries

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This Project Summary book is a published compilation consisting of short descriptions of each project supported by the Fusion Plasma Theory and Computing Group of the Advanced Physics and Technology Division of the Department of Energy, Office of Fusion Energy. The summaries contained in this volume were written by the individual contractors with minimal editing by the Office of Fusion Energy. Previous summaries were published in February of 1982 and December of 1987. The Plasma Theory program is responsible for the development of concepts and models that describe and predict the behavior of a magnetically confined plasma. Emphasis is given to the modelling and understanding of the processes controlling transport of energy and particles in a toroidal plasma and supporting the design of the International Thermonuclear Experimental Reactor (ITER). A tokamak transport initiative was begun in 1989 to improve understanding of how energy and particles are lost from the plasma by mechanisms that transport them across field lines. The Plasma Theory program has actively-participated in this initiative. Recently, increased attention has been given to issues of importance to the proposed Tokamak Physics Experiment (TPX). Particular attention has been paid to containment and thermalization of fast alpha particles produced in a burning fusion plasma as well as control of sawteeth, current drive, impurity control, and design of improved auxiliary heating. In addition, general models of plasma behavior are developed from physics features common to different confinement geometries. This work uses both analytical and numerical techniques. The Fusion Theory program supports research projects at US government laboratories, universities and industrial contractors. Its support of theoretical work at universities contributes to the office of Fusion Energy mission of training scientific manpower for the US Fusion Energy Program.

Fusion plasma theory project summaries

Science.gov (United States)

1993-10-01

This Project Summary book is a published compilation consisting of short descriptions of each project supported by the Fusion Plasma Theory and Computing Group of the Advanced Physics and Technology Division of the Department of Energy, Office of Fusion Energy. The summaries contained in this volume were written by the individual contractors with minimal editing by the Office of Fusion Energy. Previous summaries were published in February of 1982 and December of 1987. The Plasma Theory program is responsible for the development of concepts and models that describe and predict the behavior of a magnetically confined plasma. Emphasis is given to the modelling and understanding of the processes controlling transport of energy and particles in a toroidal plasma and supporting the design of the International Thermonuclear Experimental Reactor (ITER). A tokamak transport initiative was begun in 1989 to improve understanding of how energy and particles are lost from the plasma by mechanisms that transport them across field lines. The Plasma Theory program has actively participated in this initiative. Recently, increased attention has been given to issues of importance to the proposed Tokamak Physics Experiment (TPX). Particular attention has been paid to containment and thermalization of fast alpha particles produced in a burning fusion plasma as well as control of sawteeth, current drive, impurity control, and design of improved auxiliary heating. In addition, general models of plasma behavior are developed from physics features common to different confinement geometries. This work uses both analytical and numerical techniques. The Fusion Theory program supports research projects at U.S. government laboratories, universities and industrial contractors. Its support of theoretical work at universities contributes to the office of Fusion Energy mission of training scientific manpower for the U.S. Fusion Energy Program.

Fusion Plasma Theory project summaries

International Nuclear Information System (INIS)

1993-10-01

This Project Summary book is a published compilation consisting of short descriptions of each project supported by the Fusion Plasma Theory and Computing Group of the Advanced Physics and Technology Division of the Department of Energy, Office of Fusion Energy. The summaries contained in this volume were written by the individual contractors with minimal editing by the Office of Fusion Energy. Previous summaries were published in February of 1982 and December of 1987. The Plasma Theory program is responsible for the development of concepts and models that describe and predict the behavior of a magnetically confined plasma. Emphasis is given to the modelling and understanding of the processes controlling transport of energy and particles in a toroidal plasma and supporting the design of the International Thermonuclear Experimental Reactor (ITER). A tokamak transport initiative was begun in 1989 to improve understanding of how energy and particles are lost from the plasma by mechanisms that transport them across field lines. The Plasma Theory program has actively-participated in this initiative. Recently, increased attention has been given to issues of importance to the proposed Tokamak Physics Experiment (TPX). Particular attention has been paid to containment and thermalization of fast alpha particles produced in a burning fusion plasma as well as control of sawteeth, current drive, impurity control, and design of improved auxiliary heating. In addition, general models of plasma behavior are developed from physics features common to different confinement geometries. This work uses both analytical and numerical techniques. The Fusion Theory program supports research projects at US government laboratories, universities and industrial contractors. Its support of theoretical work at universities contributes to the office of Fusion Energy mission of training scientific manpower for the US Fusion Energy Program

Laser - driven high - energy ions and their application to inertial confinement fusion

International Nuclear Information System (INIS)

Borghesi, M.

2007-01-01

.Borghesi, et al., Fusion Science and Technology, 49, 412 (2006) [2] M.Roth, M.Borghesi et al, Phys. Rev. Lett., 86, 436 (2001) [3] T. Toncian, et al. Science, 312, 410 (2006) [4] A.J.Mackinnon, P.K.Patel, M.Borghesi et al., Phys Rev. Lett., 97, 045001 (2006) [5] M.Borghesi et al, Phys. Plasmas, 9, 2214 (2002)

Status report on fusion research

International Nuclear Information System (INIS)

Burkhart, Werner

2005-01-01

At the beginning of the twenty-first century mankind is faced with the serious problem of meeting the energy demands of a rapidly industrializing population around the globe. This, against the backdrop of fast diminishing fossil fuel resources (which have been the main source of energy of the last century) and the increasing realization that the use of fossil fuels has started to adversely affect our environment, has greatly intensified the quest for alternative energy sources. In this quest, fusion has the potential to play a very important role and we are today at the threshold of realizing net energy production from controlled fusion experiments. Fusion is, today, one of the most promising of all alternative energy sources because of the vast reserves of fuel, potentially lasting several thousands of years and the possibility of a relatively 'clean' form of energy, as required for use in concentrated urban industrial settings, with minimal long term environmental implications. The last decade and a half has seen unprecedented advances in controlled fusion experiments with the discovery of new regimes of operations in experiments, production of 16 MW of fusion power and operations close to and above the so-called 'break-even' conditions. A great deal of research has also been carried out in analysing various socio-economic aspects of fusion energy. This paper briefly reviews the various aspects and achievements of fusion research all over the world during this period

Introduction to plasma physics and controlled fusion

CERN Document Server

Chen, Francis F

2016-01-01

The third edition of this classic text presents a complete introduction to plasma physics and controlled fusion, written by one of the pioneering scientists in this expanding field.  It offers both a simple and intuitive discussion of the basic concepts of the subject matter and an insight into the challenging problems of current research. This outstanding text offers students a painless introduction to this important field; for teachers, a large collection of problems; and for researchers, a concise review of the fundamentals as well as original treatments of a number of topics never before explained so clearly.  In a wholly lucid manner the second edition covered charged-particle motions, plasmas as fluids, kinetic theory, and nonlinear effects.  For the third edition, two new chapters have been added to incorporate discussion of more recent advances in the field.  The new chapter 9 on Special Plasmas covers non-neutral plasmas, pure electron plasmas, solid and ultra-cold plasmas, pair-ion plasmas, d...

Cell fusion in tumor progression: the isolation of cell fusion products by physical methods

Directory of Open Access Journals (Sweden)

Vincitorio Massimo

2011-09-01

Full Text Available Abstract Background Cell fusion induced by polyethylene glycol (PEG is an efficient but poorly controlled procedure for obtaining somatic cell hybrids used in gene mapping, monoclonal antibody production, and tumour immunotherapy. Genetic selection techniques and fluorescent cell sorting are usually employed to isolate cell fusion products, but both procedures have several drawbacks. Results Here we describe a simple improvement in PEG-mediated cell fusion that was obtained by modifying the standard single-step procedure. We found that the use of two PEG undertreatments obtains a better yield of cell fusion products than the standard method, and most of these products are bi- or trinucleated polykaryocytes. Fusion rate was quantified using fluorescent cell staining microscopy. We used this improved cell fusion and cell isolation method to compare giant cells obtained in vitro and giant cells obtained in vivo from patients with Hodgkin's disease and erythroleukemia. Conclusions In the present study we show how to improve PEG-mediated cell fusion and that cell separation by velocity sedimentation offers a simple alternative for the efficient purification of cell fusion products and to investigate giant cell formation in tumor development.

International research co-operation in the field of controlled thermonuclear fusion

International Nuclear Information System (INIS)

Conscience, J.-F.

2003-01-01

This final report for the Swiss Federal Office of Education and Science presents a review of activities carried out in 2002 within the framework of the International Experimental Thermonuclear Reactor (ITER) project that involves contributions from Canada, Japan, the Russian Federation and the European Union. Further agreements on the development of a fusion reactor with other countries, including Switzerland, the USA and China, are mentioned. The first chapter describes the current state of research on electricity production using nuclear fusion and discusses feasibility, safety, environmental, fuel supply and economic aspects. A second chapter reviews global efforts in the fusion area, including ITER and EURATOM projects and the activities running under the European Fusion Development Agreement EFDA and the JET Implementing Agreement. Finally, a third chapter deals with fusion research activities in Switzerland and the contributions made to international research by Swiss universities and institutes

Testing nonlocal models of electron thermal conduction for magnetic and inertial confinement fusion applications

Science.gov (United States)

Brodrick, J. P.; Kingham, R. J.; Marinak, M. M.; Patel, M. V.; Chankin, A. V.; Omotani, J. T.; Umansky, M. V.; Del Sorbo, D.; Dudson, B.; Parker, J. T.; Kerbel, G. D.; Sherlock, M.; Ridgers, C. P.

2017-09-01

Three models for nonlocal electron thermal transport are here compared against Vlasov-Fokker-Planck (VFP) codes to assess their accuracy in situations relevant to both inertial fusion hohlraums and tokamak scrape-off layers. The models tested are (i) a moment-based approach using an eigenvector integral closure (EIC) originally developed by Ji, Held, and Sovinec [Phys. Plasmas 16, 022312 (2009)]; (ii) the non-Fourier Landau-fluid (NFLF) model of Dimits, Joseph, and Umansky [Phys. Plasmas 21, 055907 (2014)]; and (iii) Schurtz, Nicolaï, and Busquet's [Phys. Plasmas 7, 4238 (2000)] multigroup diffusion model (SNB). We find that while the EIC and NFLF models accurately predict the damping rate of a small-amplitude temperature perturbation (within 10% at moderate collisionalities), they overestimate the peak heat flow by as much as 35% and do not predict preheat in the more relevant case where there is a large temperature difference. The SNB model, however, agrees better with VFP results for the latter problem if care is taken with the definition of the mean free path. Additionally, we present for the first time a comparison of the SNB model against a VFP code for a hohlraum-relevant problem with inhomogeneous ionisation and show that the model overestimates the heat flow in the helium gas-fill by a factor of ˜2 despite predicting the peak heat flux to within 16%.

Use of data fusion to optimize contaminant transport predictions

International Nuclear Information System (INIS)

Eeckhout, E. van

1997-10-01

The original data fusion workstation, as envisioned by Coleman Research Corp., was constructed under funding from DOE (EM-50) in the early 1990s. The intent was to demonstrate the viability of fusion and analysis of data from various types of sensors for waste site characterization, but primarily geophysical. This overall concept changed over time and evolved more towards hydrogeological (groundwater) data fusion after some initial geophysical fusion work focused at Coleman. This initial geophysical fusion platform was tested at Hanford and Fernald, and the later hydrogeological fusion work has been demonstrated at Pantex, Savannah River, the US Army Letterkenny Depot, a DoD Massachusetts site and a DoD California site. The hydrogeologic data fusion package has been spun off to a company named Fusion and Control Technology, Inc. This package is called the Hydrological Fusion And Control Tool (Hydro-FACT) and is being sold as a product that links with the software package, MS-VMS (MODFLOW-SURFACT Visual Modeling System), sold by HydroGeoLogic, Inc. MODFLOW is a USGS development, and is in the public domain. Since the government paid for the data fusion development at Coleman, the government and their contractors have access to the data fusion technology in this hydrogeologic package for certain computer platforms, but would probably have to hire FACT (Fusion and Control Technology, Inc.,) and/or HydroGeoLogic for some level of software and services. Further discussion in this report will concentrate on the hydrogeologic fusion module that is being sold as Hydro-FACT, which can be linked with MS-VMS

Tritium containment of controlled thermonuclear fusion reactor

International Nuclear Information System (INIS)

Tanaka, Yoshihisa; Tsukumo, Kiyohiko; Suzuki, Tatsushi

1979-01-01

It is well known that tritium is used as the fuel for nuclear fusion reactors. The neutrons produced by the nuclear fusion reaction of deuterium and tritium react with lithium in blankets, and tritium is produced. The blankets reproduce the tritium consumed in the D-T reaction. Tritium circulates through the main cooling system and the fuel supply and evacuation system, and is accumulated. Tritium is a radioactive substance emitting β-ray with 12.6 year half-life, and harmful to human bodies. It is an isotope of hydrogen, and apt to diffuse and leak. Especially at high temperature, it permeates through materials, therefore it is important to evaluate the release of tritium into environment, to treat leaked tritium to reduce its release, and to select the method of containing tritium. The permeability of tritium and its solubility in structural materials are discussed. The typical blanket-cooling systems of nuclear fusion reactors are shown, and the tungsten coating of steam generator tubes and tritium recovery system are adopted for reducing tritium leak. In case of the Tokamak type reactor of JAERI, the tritium recovery system is installed, in which the tritium gas produced in blankets is converted to tritium steam with a Pd-Pt catalytic oxidation tower, and it is dehydrated and eliminated with a molecular sieve tower, then purified and recovered. (Kako, I.)

Developments in plasma physics and controlled fusion

International Nuclear Information System (INIS)

Thompson, W.B.

1980-01-01

Some developments in plasma physics over the past twenty years are considered from the theoretical physics standpoint under the headings; oscillations, waves and instabilities, plasma turbulence, basic kinetic theory, and developments in fusion. (UK)

International fusion research council

International Nuclear Information System (INIS)

Belozerov, A.N.

1977-01-01

A brief history of the International Fusion Research Council (IFRC) is given and the minutes of the 1976 meeting in Garching are summarized. At the Garching meeting, the IFRC evaluated the quality of papers presented at recent IAEA conferences on plasma physics and controlled thermonuclear research, and made recommendations on the organization and timing of future meetings on nuclear fusion

Feedback stabilization of the resistive shell mode in a tokamak fusion reactor

International Nuclear Information System (INIS)

Fitzpatrick, R.

1997-01-01

Stabilization of the 'resistive shell mode' is vital to the success of the 'advanced tokamak' concept. The most promising reactor relevant approach is to apply external feedback using, for instance, the previously proposed 'fake rotating shell' scheme [R. Fitzpatrick and T. H. Jensen, Phys. Plasmas 3, 2641 (1996)]. This scheme, like other simple feedback schemes, only works if the feedback controlled conductors are located inside the 'critical radius' at which a perfectly conducting shell is just able to stabilize the ideal external kink mode. In general, this is not possible in a reactor, since engineering constraints demand that any feedback controlled conductors be placed outside the neutron shielding blanket (i.e., relatively far from the edge of the plasma). It is demonstrated that the fake rotating shell feedback scheme can be modified so that it works even when the feedback controlled conductors are located well beyond the critical radius. The gain, bandwidth, current, and total power requirements of such a feedback system for a reactor sized plasma are estimated to be less than 100, a few Hz, a fews tens of kA, and a few MW, respectively. These requirements could easily be met using existing technology. It is concluded that feedback stabilization of the resistive shell mode is possible in a tokamak fusion reactor. copyright 1997 American Institute of Physics

Inertial-confinement fusion with lasers

International Nuclear Information System (INIS)

Betti, R.; Hurricane, O. A.

2016-01-01

The quest for controlled fusion energy has been ongoing for over a half century. The demonstration of ignition and energy gain from thermonuclear fuels in the laboratory has been a major goal of fusion research for decades. Thermonuclear ignition is widely considered a milestone in the development of fusion energy, as well as a major scientific achievement with important applications to national security and basic sciences. The U.S. is arguably the world leader in the inertial con fment approach to fusion and has invested in large facilities to pursue it with the objective of establishing the science related to the safety and reliability of the stockpile of nuclear weapons. Even though significant progress has been made in recent years, major challenges still remain in the quest for thermonuclear ignition via laser fusion

Retraction: On the origin of power-law distributions in systems with constrained phase space [Condens. Matter Phys., 2013, vol. 16, 43802

Directory of Open Access Journals (Sweden)

Editorial Board

2014-03-01

Full Text Available The article Condens. Matter Phys., 2013, vol. 16, 43802 ( DOI:10.5488/CMP.16.43802 has been retracted by the decision of the Editorial Board. There is a significant overlap with an article: Phys. Rev. E, 2006, vol. 74, 036120 ( DOI:10.1103/PhysRevE.74.036120. Appologies are offered to readers of the journal that this was not detected during the submission process.

Magneized target fusion: An overview of the concept

International Nuclear Information System (INIS)

Kirkpatrick, R.C.

1994-01-01

Magnetized target fusion (MTF) seeks to take advantage of the reduction of thermal conductivity through the application of a strong magneticfield and thereby ease the requirements for reaching fusion conditions in a thermonuclear (TN) fusion fuel. A potentially important benefit of the strong field in the partial trapping of energetic charged particles to enhance energy deposition by the TN fusion reaction products. The essential physics is described. MTF appears to lead to fusion targets that require orders of magnitude less power and intensity for fusion ignition than currently proposed (unmagnetized) inertial confinement fusion (ICF) targets do, making some very energetic pulsed power drivers attractive for realizing controlled fusion

On the economics of fusion breeders

International Nuclear Information System (INIS)

Greenspan, E.

1984-01-01

The potential for improving the economics of tandem mirror fusion breeders by assisting them with tritium produced in the control of the client light water reactors and/or by operating them with polarized plasma is assessed. Also assessed is the promise of a Starfire tokamak and a compact reversed field pinch fusion driver for fusion breeder applications. All three approaches are found to promise a significant reduction in the cost of fusion breeder produced fissile fuel, potentially making the FB-LWR system economically competitive with conventional nuclear energy systems. (orig.) [de

Controlled energy generation from nuclear fusion. 60th year atw

Energy Technology Data Exchange (ETDEWEB)

Weiss, Georg [Pintsch Bamag AG, Frankfurt am Main (Germany)

2015-02-15

Prospects increase, that with a controlled process of nuclear fusion one day an additional nuclear energy source will be commercially exploitable. In what follows, scientific principles according to the most recent research will be presented. Since approximately 30 years we are aware of the fact, that energy in form of light and heat provided by the sun and other fixed stars since over four billions years resulted from reactions of atomic nuclei. A series of such reactions became known which are considered for 'thermonuclear' processes, for example the carbon cycle by Bethe, where hydrogen is converted into helium. Most of the reflections and experiments dealt until 1938 with the reaction between nuclei of light elements. The possibility of splitting heavy nuclei was not anticipated. Its discovery by Hahn and Strassmann was a complete surprise - so to speak a rash reaction to release energy at the end of the element row. This 'way out' captured the interest of nuclear physicist for more than a decade. Only today, by starting to construct big nuclear power plants - only today, being able to assess the possibilities and limitations of this technology, the idea of energy generation through nuclear fusion steps into the foreground of nuclear research.

Invited and contributed papers presented at the 22. EPS conference on controlled fusion and plasma physics

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

In this report one invited and fifteen contributed papers by researchers of the `Centre de Recherche en Physique des Plasmas`, Lausanne, to the 22. EPS Conference on Controlled Fusion and Plasma Physics are assembled. figs., tabs., refs.

The yeast cell fusion protein Prm1p requires covalent dimerization to promote membrane fusion.

Directory of Open Access Journals (Sweden)

Alex Engel

2010-05-01

Full Text Available Prm1p is a multipass membrane protein that promotes plasma membrane fusion during yeast mating. The mechanism by which Prm1p and other putative regulators of developmentally controlled cell-cell fusion events facilitate membrane fusion has remained largely elusive. Here, we report that Prm1p forms covalently linked homodimers. Covalent Prm1p dimer formation occurs via intermolecular disulfide bonds of two cysteines, Cys-120 and Cys-545. PRM1 mutants in which these cysteines have been substituted are fusion defective. These PRM1 mutants are normally expressed, retain homotypic interaction and can traffic to the fusion zone. Because prm1-C120S and prm1-C545S mutants can form covalent dimers when coexpressed with wild-type PRM1, an intermolecular C120-C545 disulfide linkage is inferred. Cys-120 is adjacent to a highly conserved hydrophobic domain. Mutation of a charged residue within this hydrophobic domain abrogates formation of covalent dimers, trafficking to the fusion zone, and fusion-promoting activity. The importance of intermolecular disulfide bonding informs models regarding the mechanism of Prm1-mediated cell-cell fusion.

Perceptual relearning of binocular fusion after hypoxic brain damage: four controlled single-case treatment studies.

Science.gov (United States)

Schaadt, Anna-Katharina; Schmidt, Lena; Kuhn, Caroline; Summ, Miriam; Adams, Michaela; Garbacenkaite, Ruta; Leonhardt, Eva; Reinhart, Stefan; Kerkhoff, Georg

2014-05-01

Hypoxic brain damage is characterized by widespread, diffuse-disseminated brain lesions, which may cause severe disturbances in binocular vision, leading to diplopia and loss of stereopsis, for which no evaluated treatment is currently available. The study evaluated the effects of a novel binocular vision treatment designed to improve binocular fusion and stereopsis as well as to reduce diplopia in patients with cerebral hypoxia. Four patients with severely reduced convergent fusion, stereopsis, and reading duration due to hypoxic brain damage were treated in a single-subject baseline design, with three baseline assessments before treatment to control for spontaneous recovery (pretherapy), an assessment immediately after a treatment period of 6 weeks (posttherapy), and two follow-up tests 3 and 6 months after treatment to assess stability of improvements. Patients received a novel fusion and dichoptic training using 3 different devices designed to slowly increase fusional and disparity angle. After the treatment, all 4 patients improved significantly in binocular fusion, subjective reading duration until diplopia emerged, and 2 of 4 patients improved significantly in local stereopsis. No significant changes were observed during the pretherapy baseline period and the follow-up period, thus ruling out spontaneous recovery and demonstrating long-term stability of treatment effects. This proof-of-principle study indicates a substantial treatment-induced plasticity after hypoxia in the relearning of binocular vision and offers a viable treatment option. Moreover, it provides new hope and direction for the development of effective rehabilitation strategies to treat neurovisual deficits resulting from hypoxic brain damage.

International research co-operation in the field of controlled thermonuclear fusion

International Nuclear Information System (INIS)

2004-01-01

This 26th report by the Swiss Federal Office for Education and Science presents a review of work done in Swiss institutes in 2003 as part of international research into thermonuclear fusion. A broad outline of the project and of its significance within the wider field of thermonuclear fusion research is given. This is followed by a review of the significant events in the world of fusion research, with emphasis placed on ITER and on the EURATOM fusion programme. A further chapter summarises events in Switzerland in 2003 and the report closes with a list of contacts for more information. Three annexes provide information on the current situation in fusion research, as well as scientific and technical highlights of the work performed in 2003 at the Plasma Physics Research Centre CRPP at the Federal Institute of Technology EPFL in Lausanne, Switzerland. Annex 3 reports on results obtained at the Physics Institute of the University of Basle. The annexes are for the benefit of the technically and scientifically versed reader, and brief summaries of them are given in the main body of the report

Comment on “Stationary self-focusing of Gaussian laser beam in relativistic thermal quantum plasma” [Phys. Plasmas 20, 072703 (2013)

International Nuclear Information System (INIS)

Habibi, M.; Ghamari, F.

2014-01-01

Patil and Takale in their recent article [Phys. Plasmas 20, 072703 (2013)], by evaluating the quantum dielectric response in thermal quantum plasma, have modeled the relativistic self-focusing of Gaussian laser beam in a plasma. We have found that there are some important shortcomings and fundamental mistakes in Patil and Takale [Phys. Plasmas 20, 072703 (2013)] that we give a brief description about them and refer readers to important misconception about the use of the Fermi temperature in quantum plasmas, appearing in Patil and Takale [Phys. Plasmas 20, 072703 (2013)

Controlled thermonuclear fusion. Present state and prospective

International Nuclear Information System (INIS)

Consoli, T.

1976-01-01

The interest of thermonuclear fusion for energy production is underlined. The present state of the research in this field is presented, emphasis being given to Tokamak configurations. The problems concerning confinement and additional heating in these devices are presented [fr

The transition zone above a lumbosacral fusion.

Science.gov (United States)

Hambly, M F; Wiltse, L L; Raghavan, N; Schneiderman, G; Koenig, C

1998-08-15

The clinical and radiographic effect of a lumbar or lumbosacral fusion was studied in 42 patients who had undergone a posterolateral fusion with an average follow-up of 22.6 years. To examine the long-term effects of posterolateral lumbar or lumbosacral fusion on the cephalad two motion segments (transition zone). It is commonly held that accelerated degeneration occurs in the motion segments adjacent to a fusion. Most studies are of short-term, anecdotal, uncontrolled reports that pay particular attention only to the first motion segment immediately cephalad to the fusion. Forty-two patients who had previously undergone a posterolateral lumbar or lumbosacral fusion underwent radiographic and clinical evaluation. Rate of fusion, range of motion, osteophytes, degenerative spondylolisthesis, retrolisthesis, facet arthrosis, disc ossification, dynamic instability, and disc space height were all studied and statistically compared with an age- and gender-matched control group. The patient's self-reported clinical outcome was also recorded. Degenerative changes occurred at the second level above the fused levels with a frequency equal to those occurring in the first level. There was no statistical difference between the study group and the cohort group in the presence of radiographic changes within the transition zone. In those patients undergoing fusion for degenerative processes, 75% reported a good to excellent outcome, whereas 84% of those undergoing fusion for spondylolysis or spondylolisthesis reported a good to excellent outcome. Radiographic changes occur within the transition zone cephalad to a lumbar or lumbosacral fusion. However, these changes are also seen in control subjects who have had no surgery.

Beam dancer fusion device

International Nuclear Information System (INIS)

Maier, H.B.

1984-01-01

To accomplish fusion of two or more fusion fuel elements numerous minute spots of energy or laser light are directed to a micro target area, there to be moved or danced about by a precision mechanical controlling apparatus at the source of the laser light or electromagnetic energy beams, so that merging and coinciding patterns of light or energy beams can occur around the area of the fuel atoms or ions. The projecting of these merging patterns may be considered as target searching techniques to locate responsive clusters of fuel elements and to compress such elements into a condition in which fusion may occur. Computerized programming may be used

Papers presented at the fourteenth international conference on plasma physics and controlled nuclear fusion research

International Nuclear Information System (INIS)

1994-01-01

This report contains the contributions of the CIEMAT's Fusion Unit to the 14th International Conference on Plasma Physics and Controlled Nuclear Fusion Research that was held by the International Atomic Energy Agency in Wurzburg, Germany from 30 September to 7 October 1992. Three papers were presented that summarized the main lines of work done in the Unit during the previous two years: The first one on the theoretical advances in the understanding of the Flexible Heliac TJ-II under construction, the second on the confinement studies performed in the operating TJ-I Tokamak and the third one on the description of the physical properties of the soon to be started TJ-IU Torsatron. (Author) 25 refs

Extending the capabilities of the DIII-D Plasma Control System for worldwide fusion research collaborations

International Nuclear Information System (INIS)

Penaflor, B.G.; Ferron, J.R.; Walker, M.L.; Humphreys, D.A.; Leuer, J.A.; Piglowski, D.A.; Johnson, R.D.; Xiao, B.J.; Hahn, S.H.; Gates, D.A.

2009-01-01

This paper will discuss the recent enhancements which have been made to the DIII-D Plasma Control System (PCS) in order to further extend its usefulness as a shared tool for worldwide fusion research. The PCS developed at General Atomics is currently being used in a number of fusion research experiments worldwide, including the DIII-D Tokamak Facility in San Diego, and most recently the KSTAR Tokamak in South Korea. A number of enhancements have been made to support the ongoing needs of the DIII-D Tokamak in addition to meeting the needs of other PCS users worldwide. Details of the present PCS hardware and software architecture along with descriptions of the latest enhancements will be given.

Distributed intelligence in a LAN architecture increases the flexibility in control systems for fusion experiments

International Nuclear Information System (INIS)

Tenten, W.; Fuss, L.; Hoge, W.

1987-01-01

The control system for the TEXTOR Neutral Beam Injectors is designed implementing approved concepts and techniques. A powerful super mini computer serves as a central node between the operators console and the experimental process. Devices form a console for suitable man machine interaction. The link to the process is mainly based on communication with a network of industry standard programmable controllers. A distinction is made between the functionally dedicated and in most cases locally distributed logic controllers, a central controller and the computerized console level. Introduction of such networks in control system for fusion experiments results in a number of advantages

Controlled thermonuclear fusion and the latest progress on China's HT-7 superconducting tokamak

International Nuclear Information System (INIS)

Li Jiangang; Yang Yu

2003-01-01

After 50 years of research on controlled thermonuclear fusion, a new stage will be reached in 2003, when a site for the International Thermonuclear Experimental Reactor project will be chosen to start the construction. Scientists hope that this project could herald a new era in which the energy problem will be solved completely. The great progress made on the HT-7 superconducting tokamak in China has provided positive and powerful support for fusion research. The HT-7 is one of the only two superconducting tokamaks in the world that can carry out minute-scale high temperature plasma research, and has achieved a duration of 63.95s for the hot plasma discharge. This is a major step towards real steady-state operation of the tokamak configuration. We present an overview of the latest progress on the tokamak experiments in the Institute of Plasma Physics, Chinese Academy of Sciences

Research programme on controlled thermonuclear fusion - Synthesis report 2010

International Nuclear Information System (INIS)

Vaucher, C.; Tran, M. Q.; Villard, L.; Marot, L.

2011-01-01

Since 1978, research on thermonuclear fusion in Switzerland is closely related to the research programme of the European Atomic Energy Community (EURATOM). The Swiss projects tackle aspects of plasma physics and fusion technology. Switzerland participates to the construction and operation of the Joint European Torus (JET). The International Thermonuclear Experimental Reactor (ITER) is being built; the first plasma is expected in 2019. The 'Centre de Recherches en Physique des Plasmas' (CRPP) of the EPFL participates to EURATOM scientific and technological projects in magnetic confinement physics, through an experimental contribution (the Variable Configuration Tokamak, TCV) and theoretical studies. Thanks to the large flexibility of the TCV design and operation modus, plasmas of different shapes can be created and controlled, what is a very useful option to verify numerical simulation results. Besides, the injection of millimetre waves allows directing the injected power according to specific profiles. A configuration of type 'snowflakes' could be created, reducing the power deposition at the edge of the plasma. Theoretical studies on turbulence have improved the plasma stability in the TCV. For the first time in the world, TCV could reach a stable plasma, the plasma current being generated using the so-called 'bootstrap' phenomenon. Besides turbulence, studies were focused on heat and particle transport in tokamaks, on an analysis of the equilibrium and magneto-hydrodynamic stability of tokamaks and stellarators, on the application of radiofrequency waves and on the optimization of new confinement configurations. Experiments in the JET facility confirmed the numerical results of theoretical simulations. The TORPEX facility, which is simpler than TCV, allows high space-temporal resolution measurements for the study of turbulences and plasma threads ('blobs'). At the Paul Scherrer Institute (PSI), research topics include superconductivity and materials. The Fusion

The perspectives of fusion energy: The roadmap towards energy production and fusion energy in a distributed energy system

DEFF Research Database (Denmark)

Naulin, Volker; Juul Rasmussen, Jens; Korsholm, Søren Bang

2014-01-01

at very high temperature where all matter is in the plasma state as the involved energies are orders of magnitude higher than typical chemical binding energies. It is one of the great science and engineering challenges to construct a viable power plant based on fusion energy. Fusion research is a world...... The presentation will discuss the present status of the fusion energy research and review the EU Roadmap towards a fusion power plant. Further the cost of fusion energy is assessed as well as how it can be integrated in the distributed energy system......Controlled thermonuclear fusion has the potential of providing an environmentally friendly and inexhaustible energy source for mankind. Fusion energy, which powers our sun and the stars, is released when light elements, such as the hydrogen isotopes deuterium and tritium, fuse together. This occurs...

Mass Producing Targets for Nuclear Fusion

Science.gov (United States)

Wang, T. G.; Elleman, D. D.; Kendall, J. M.

1983-01-01

Metal-encapsulating technique advances prospects of controlling nuclear fusion. Prefilled fusion targets form at nozzle as molten metal such as tin flows through outer channel and pressurized deuterium/tritium gas flows through inner channel. Molten metal completely encloses gas charge as it drops off nozzle.

Fusion environment sensitive flow and fracture processes

International Nuclear Information System (INIS)

1980-01-01

As a planning activity, the objectives of the workshop were to list, prioritize and milestone the activities necessary to understand, interpret and control the mechanical behavior of candidate fusion reactor alloys. Emphasis was placed on flow and fracture processes which are unique to the fusion environment since the national fusion materials program must evaluate these effects without assistance from other reactor programs

The role of improved fusion concepts

International Nuclear Information System (INIS)

Nelson, D.B.; Linford, R.K.; Liu, C.S.; Logan, B.G.; Rose, P.H.

1985-01-01

The U.S. Dept. of Energy discusses concept improvement in the tokamak and concept improvement in the mirror. Controlled Thermonuclear Research comments on what constitutes an attractive fusion reactor, and provides a table of achieved parameters of RFP, FRC and the spheromak experiments. GA Technologies Inc. remarks on the direction which industry must take in the fusion program. The Lawrence Livermore National Laboratory concentrates on commercial reactor studies. Spectra Technology focuses on problems dealing with fusion proponents making a convincing and clear economic argument for fusion based on a mils per kilowat basis, and the large costs of flagship experiments. The Oak Ridge National Laboratory remarks on the need for an economic energy source for fusion. A table of cost of electricity contours is shown

The role of improved fusion concepts

Energy Technology Data Exchange (ETDEWEB)

Nelson, D.B.; Linford, R.K.; Liu, C.S.; Logan, B.G.; Rose, P.H.

1985-06-01

The U.S. Dept. of Energy discusses concept improvement in the tokamak and concept improvement in the mirror. Controlled Thermonuclear Research comments on what constitutes an attractive fusion reactor, and provides a table of achieved parameters of RFP, FRC and the spheromak experiments. GA Technologies Inc. remarks on the direction which industry must take in the fusion program. The Lawrence Livermore National Laboratory concentrates on commercial reactor studies. Spectra Technology focuses on problems dealing with fusion proponents making a convincing and clear economic argument for fusion based on a mils per kilowat basis, and the large costs of flagship experiments. The Oak Ridge National Laboratory remarks on the need for an economic energy source for fusion. A table of cost of electricity contours is shown.

Improving Vehicle Ride and Handling Using LQG CNF Fusion Control Strategy for an Active Antiroll Bar System

Directory of Open Access Journals (Sweden)

N. Zulkarnain

2014-01-01

Full Text Available This paper analyses a comparison of performance for an active antiroll bar (ARB system using two types of control strategy. First of all, the LQG control strategy is investigated and then a novel LQG CNF fusion control method is developed to improve the performances on vehicle ride and handling for an active antiroll bar system. However, the ARB system has to balance the trade-off between ride and handling performance, where the CNF consists of a linear feedback law and a nonlinear feedback law. Typically, the linear feedback is designed to yield a quick response at the initial stage, while the nonlinear feedback law is used to smooth out overshoots in the system output when it approaches the target reference. The half car model is combined with a linear single track model with roll dynamics which are used for the analysis and simulation of ride and handling. The performances of the control strategies are compared and the simulation results show the LQG CNF fusion improves the performances in vehicle ride and handling.

Overview of fusion reactor safety

International Nuclear Information System (INIS)

Cohen, S.; Crocker, J.G.

1981-01-01

Use of deuterium-tritium burning fusion reactors requires examination of several major safety and environmental issues: (1) tritium inventory control, (2) neutron activation of structural materials, fluid streams and reactor hall environment, (3) release of radioactivity from energy sources including lithium spill reactions, superconducting magnet stored energy release, and plasma disruptions, (4) high magnetic and electromagnetic fields associated with fusion reactor superconducting magnets and radio frequency heating devices, and (5) handling and disposal of radioactive waste. Early recognition of potential safety problems with fusion reactors provides the opportunity for improvement in design and materials to eliminate or greatly reduce these problems. With an early start in this endeavor, fusion should be among the lower risk technologies for generation of commercial electrical power

Thermonuclear fusion power

Energy Technology Data Exchange (ETDEWEB)

Lehnert, B

1977-01-01

The present state and future possibilities of controlled-nuclear-fusion research are reviewed, including basic concepts and problems, as well as various approaches based on magnetic- and nonmagnetic-confinement schemes. Considerable progress has so far been made in both plasma physics and fusion-reactor technology, and a closer relationship has been established between theory and experiments. Still, none of the present approaches will, for certain, lead to the final solution of a full-scale reactor. Intensified work along broad lines, with emphasis also on basic research and new ideas, is necessary for future success.

Improving Science Teacher Preparation through the APS PhysTEC and NSF Noyce Programs

Science.gov (United States)

Williams, Tasha; Tyler, Micheal; van Duzor, Andrea; Sabella, Mel

2013-03-01

Central to the recruitment of students into science teaching at a school like CSU, is a focus on the professional nature of teaching. The purpose of this focus is twofold: it serves to change student perceptions about teaching and it prepares students to become teachers who value continued professional development and value the science education research literature. The Noyce and PhysTEC programs at CSU place the professional nature of teaching front and center by involving students in education research projects, paid internships, attendance at conferences, and participation in a new Teacher Immersion Institute and a Science Education Journal Reading Class. This poster will focus on specific components of our teacher preparation program that were developed through these two programs. In addition we will describe how these new components provide students with diverse experiences in the teaching of science to students in the urban school district. Supported by the NSF Noyce Program (0833251) and the APS PhysTEC Program.

Design concept of control system for cryogenic distillation columns of fusion reactor

International Nuclear Information System (INIS)

Yamanishi, Toshihiko; Okuno, Kenji

1993-09-01

Control systems were designed for cryogenic distillation columns in the main fuel cycle and the breeder blanket interface systems of fusion reactors. Three basic control modes were proposed for the column whose top product was more important; the column whose bottom product is more important; and the column having a feed back stream. The key component in the important product stream was selected for each column, and the analysis method for measurement of this key component was discussed. Some of the columns need the gas chromatography as the analysis instrument of the control system. The time required for the measurement of product purity by the gas chromatography considerably affects the stability of the control system. A significant conclusion is that permissible time is about 20 min. It is possible to complete the measurement within 20 minute by the gas chromatography. The gas chromatography is applicable for the control system of the column. (author)

Argonne National Laboratory papers presented at third ANS topical meeting on the technology of controlled nuclear fusion

International Nuclear Information System (INIS)

1978-01-01

The 9 papers included in this Technical Memorandum were presented at the Third ANS Topical Meeting on the Technology of Controlled Nuclear Fusion that was held in Santa Fe, New Mexico on May 9-11, 1978

Fusion energy research for ITER and beyond

International Nuclear Information System (INIS)

Romanelli, Francesco; Laxaaback, Martin

2011-01-01

The achievement in the last two decades of controlled fusion in the laboratory environment is opening the way to the realization of fusion as a source of sustainable, safe and environmentally responsible energy. The next step towards this goal is the construction of the International Thermonuclear Experimental Reactor (ITER), which aims to demonstrate net fusion energy production on the reactor scale. This paper reviews the current status of magnetic confinement fusion research in view of the ITER project and provides an overview of the main remaining challenges on the way towards the realization of commercial fusion energy production in the second half of this century. (orig.)

Ceramics for fusion devices

International Nuclear Information System (INIS)

Clinard, F.W. Jr.

1984-01-01

Ceramics are required for a number of applications in fusion devices, among the most critical of which are magnetic coil insulators, windows for RF heating systems, and structural uses. Radiation effects dominate consideration of candidate materials, although good pre-irradiation properties are a requisite. Materials and components can be optimized by careful control of chemical and microstructural content, and application of brittle material design and testing techniques. Future directions for research and development should include further extension of the data base in the areas of electrical, structural, and thermal properties; establishment of a fission neutron/fusion neutron correlation including transmutation gas effects; and development of new materials tailored to meet the specific needs of fusion reactors

Comparison of low confinement mode transport simulations using the mixed Bohm/gyro-Bohm and the Multi-Mode-95 transport model

International Nuclear Information System (INIS)

Onjun, Thawatchai; Bateman, Glenn; Kritz, Arnold H.; Hannum, David

2001-01-01

Predictive transport simulations using the mixed Bohm/gyro-Bohm (JET) transport model [M. Erba , Plasma Phys. Controlled Fusion 39, 261 (1997)] are compared with simulations using the Multi-Mode-95 (MMM95) transport model [G. Bateman , Phys. Plasmas 5, 1793 (1998)]. Temperature and density profiles from these simulations are compared with experimental data for 13 low confinement mode (L-mode) discharges from the Doublet III-D Tokamak (DIII-D) [J. L. Luxon and L. G. Davis, Fusion Technol. 8, 441 (1985)] and the Tokamak Fusion Test Reactor (TFTR) [D. Grove and D. M. Meade, Nucl. Fusion 25, 1167 (1985)]. The selected discharges include systematic scans over gyro-radius, plasma power, current, and density. It is found that simulations using the two models match experimental data equally well, in spite of the fact that the JET model has predominantly Bohm scaling (proportional to gyro-radius) while the MMM95 model has a purely gyro-Bohm scaling (proportional to gyro-radius squared)

A neutron poison tritium breeding controller applied to a water cooled fusion reactor model

International Nuclear Information System (INIS)

Morgan, L.W.G.; Packer, L.W.

2014-01-01

Highlights: • The issue of a potentially producing a large tritium surplus inventory, within a solid breeder, is addressed. • A possible solution to this problem is presented in the form of a neutron poison based tritium production controller. • The tritium surplus inventory has been modelled by the FATI code for a simplified WCCB model and as a function of time. • It has been demonstrated that the tritium surplus inventory can be managed, which may impact on safety considerations. - Abstract: The generation of tritium in sufficient quantities is an absolute requirement for a next step fusion device such as DEMO due to the scarcity of tritium sources. Although the production of sufficient quantities of tritium will be one of the main challenges for DEMO, within an energy economy featuring several fusion power plants the active control of tritium production may be required in order to manage surplus tritium inventories at power plant sites. The primary reason for controlling the tritium inventory in such an economy would therefore be to minimise the risk and storage costs associated with large quantities of surplus tritium. In order to ensure that enough tritium will be produced in a reactor which contains a solid tritium breeder, over the reactor's lifetime, the tritium breeding rate at the beginning of its lifetime is relatively high and reduces over time. This causes a large surplus tritium inventory to build up until approximately halfway through the lifetime of the blanket, when the inventory begins to decrease. This surplus tritium inventory could exceed several tens of kilograms of tritium, impacting on possible safety and licensing conditions that may exist. This paper describes a possible solution to the surplus tritium inventory problem that involves neutron poison injection into the coolant, which is managed with a tritium breeding controller. A simple PID controller and is used to manage the injection of the neutron absorbing compounds into

A neutron poison tritium breeding controller applied to a water cooled fusion reactor model

Energy Technology Data Exchange (ETDEWEB)

Morgan, L.W.G., E-mail: Lee.Morgan@CCFE.ac.uk; Packer, L.W.

2014-10-15

Highlights: • The issue of a potentially producing a large tritium surplus inventory, within a solid breeder, is addressed. • A possible solution to this problem is presented in the form of a neutron poison based tritium production controller. • The tritium surplus inventory has been modelled by the FATI code for a simplified WCCB model and as a function of time. • It has been demonstrated that the tritium surplus inventory can be managed, which may impact on safety considerations. - Abstract: The generation of tritium in sufficient quantities is an absolute requirement for a next step fusion device such as DEMO due to the scarcity of tritium sources. Although the production of sufficient quantities of tritium will be one of the main challenges for DEMO, within an energy economy featuring several fusion power plants the active control of tritium production may be required in order to manage surplus tritium inventories at power plant sites. The primary reason for controlling the tritium inventory in such an economy would therefore be to minimise the risk and storage costs associated with large quantities of surplus tritium. In order to ensure that enough tritium will be produced in a reactor which contains a solid tritium breeder, over the reactor's lifetime, the tritium breeding rate at the beginning of its lifetime is relatively high and reduces over time. This causes a large surplus tritium inventory to build up until approximately halfway through the lifetime of the blanket, when the inventory begins to decrease. This surplus tritium inventory could exceed several tens of kilograms of tritium, impacting on possible safety and licensing conditions that may exist. This paper describes a possible solution to the surplus tritium inventory problem that involves neutron poison injection into the coolant, which is managed with a tritium breeding controller. A simple PID controller and is used to manage the injection of the neutron absorbing compounds into

Fusion of hard and soft control strategies for the robotic hand

CERN Document Server

Chen, Cheng-Hung

2018-01-01

Long considered the stuff of science fiction, a prosthetic hand capable of fully replicating all of that appendage's various functions is closer to becoming reality than ever before. This book provides a comprehensive report on exciting recent developments in hybrid control techniques—one of the most crucial hurdles to be overcome in creating smart prosthetic hands. Coauthored by two of the world's foremost pioneering experts in the field, Fusion of Hard and Soft Control Strategies for the Robotic Hand treats robotic hands for multiple applications. It begins with an overview of advances in main control techniques that have been made over the past decade before addressing the military context for affordable robotic hand technology with tactile and/or proprioceptive feedback for hand amputees. Kinematics, homogene us transformations, inverse and differential kinematics, trajectory planning, and dynamic models of two-link thumb and three-link index finger are discussed in detail. The remainder of the book is...

Control of ITBs in Fusion Self-Heated Plasmas

Science.gov (United States)

Panta, Soma; Newman, David; Terry, Paul; Sanchez, Raul

2015-11-01

Simple dynamical models have been able to capture a remarkable amount of the dynamics of the transport barriers found in many devices, including the often disconnected nature of the electron thermal transport channel sometimes observed in the presence of a standard (``ion channel'') barrier. By including in this rich though simple dynamic transport model an evolution equation for electron fluctuations we have previously investigated the interaction between the formation of the standard ion channel barrier and the somewhat less common electron channel barrier. The electron channel formation and evolution is even more sensitive to the alignment of the various gradients making up the sheared radial electric field then the ion barrier is. Because of this sensitivity and coupling of the barrier dynamics, the dynamic evolution of the fusion self-heating profile can have a significant impact on the barrier location and dynamics. To investigate this, self-heating has been added this model and the impact of the self-heating on the formation and controllability of the various barriers is explored. It has been found that the evolution of the heating profiles can suppress or collapse the electron channel barrier. NBI and RF schemes will be investigated for profile/barrier control.

The history of controlled fusion research

International Nuclear Information System (INIS)

Trocheris, M.

1980-01-01

The idea of using nuclear reaction between light elements to produce energy for peaceful objectives originated towards the mid-forties. In this work, the author traces the various stages of reserach undertaken in this field from the first fusion experiments to the projects now in course of production. Research scientists have travelled a long, hard road to reach a new development phase during which technological problems will play a prominent part [fr

The ORNL Controlled Fusion Atomic Data Center: Overview of Activities 2011

International Nuclear Information System (INIS)

Schultz, D.R.

2011-01-01

The Controlled Fusion Atomic Data Center (CFADC) of the Oak Ridge National Laboratory continued operation aimed at collecting, evaluating, and disseminating atomic, molecular, and particle-surface interaction (AM and PSI) data needed by both the U.S. and international plasma science communities. This work has been carried out within an overarching atomic physics research group which produces much of the required data through an active experimental and theoretical science program. The production of an annotated bibliography of AM and PSI literature relevant to plasma science continues to be among the most important activities of the data center, forming the basis for the CFADC on-line bibliographic search engine and a significant part of the IAEA A+M Data Unit's 'International Bulletin on Atomic and Molecular Data for Fusion.' Also chief among the data center's activities are responses to specific data requests from the plasma science community, leading to either rapid feedback using existing data resources or long term data production projects, as well as participation in IAEA Coordinated Research Programs including recently 'Data for Surface Composition Dynamics Relevant to Erosion Processes' and 'Atomic and Molecular Data for Plasma Modeling.' Highlights of recent data production projects include the following: Experimental and theoretical data for inelastic electron-hydrocarbon reactions, large scale computational results for particle reflection from surfaces, measurements of chemical sputtering from carbon, inaugural experiments considering molecular ion collisions with neutral hydrogen, and expansion of the database of elastic and related transport cross sections calculated for intrinsic and extrinsic impurities in hydrogen plasmas. Progress is being hampered owing to news from the US Department of Energy that it plans to close out the program after a ramp down of funding in 2012, following a distinguished 52 year history of contributions to the US and

Fusion research in Hungary

International Nuclear Information System (INIS)

Zoletnik, S.

2004-01-01

Hungarian fusion research started in the 1970s, when the idea of installing a small tokamak experiment emerged. In return to computer equipment a soviet tokamak was indeed sent to Hungary and started to operate as MT-1 at the Central Research Institute for Physics (KFKI) in 1979. Major research topics included diagnostic development, edge plasma studies and investigation of disruptions. Following a major upgrade in 1992 (new vacuum vessel, active position control and PC network based data acquisition system) the MT-1M tokamak was used for the study of transport processes with trace impurity injection, micropellet ablation studies, X-ray tomography and laser blow-off diagnostic development. Although funding ceased in the middle of the 90's the group was held alive by collaborations with EU fusion labs: FZ -Juelich, IPP-Garching and CRPP-EPFL Lausanne. In 1998 the machine was dismantled due to reorganization of the Hungarian Academy of Sciences. New horizons opened to fusion research from 1999, when Hungary joined EURATOM and a fusion Association was formed. Since then fusion physics studies are done in collaboration with major EU fusion laboratories, Hungarian researchers also play an active role in JET diagnostics upgrade and ITER design. Major topics are pellet ablation studies, plasma turbulence diagnosis using Beam Emission Spectroscopy and other techniques, tomography and plasma diagnostics using various neutral beams. In fusion relevant technology R and D Hungary has less records. Before joining EURATOM some materials irradiation studies were done at the Budapest Research Reactor at KFKI-AEKI. The present day fusion technology programme focuses still on irradiation studies, nuclear material database and electromagnetic testing techniques. Increasing the fusion technology research activities is a difficult task, as the competition in Hungarian industry is very strong and the interest of organizations in long-term investments into R and D is rather weak and

International fusion research

International Nuclear Information System (INIS)

Pease, R.S.

1983-01-01

Nuclear energy of the light elements deuterium and lithium can be released if the 100 MK degree temperature required for deuterium-tritium thermonuclear fusion reactions can be achieved together with sufficient thermal insulation for a net energy yield. Progress of world-wide research shows good prospect for these physical conditions being achieved by the use of magnetic field confinement and of rapidly developing heating methods. Tokamak systems, alternative magnetic systems and inertial confinement progress are described. International co-operation features a number of bilateral agreements between countries: the Euratom collaboration which includes the Joint European Torus, a joint undertaking of eleven Western European nations of Euratom, established to build and operate a major confinement experiment; the development of co-operative projects within the OECD/IEA framework; the INTOR workshop, a world-wide study under IAEA auspices of the next major step in fusion research which might be built co-operatively; and assessments of the potential of nuclear fusion by the IAEA and the International Fusion Research Council. The INTOR (International Tokamak Reactor) studies have outlined a major plant of the tokamak type to study the engineering and technology of fusion reactor systems, which might be constructed on a world-wide basis to tackle and share the investment risks of the developments which lie ahead. This paper summarizes the recent progress of research on controlled nuclear fusion, featuring those areas where international co-operation has played an important part, and describes the various arrangements by which this international co-operation is facilitated. (author)

Fusion Simulation Program

International Nuclear Information System (INIS)

Greenwald, Martin

2011-01-01

Many others in the fusion energy and advanced scientific computing communities participated in the development of this plan. The core planning team is grateful for their important contributions. This summary is meant as a quick overview the Fusion Simulation Program's (FSP's) purpose and intentions. There are several additional documents referenced within this one and all are supplemental or flow down from this Program Plan. The overall science goal of the DOE Office of Fusion Energy Sciences (FES) Fusion Simulation Program (FSP) is to develop predictive simulation capability for magnetically confined fusion plasmas at an unprecedented level of integration and fidelity. This will directly support and enable effective U.S. participation in International Thermonuclear Experimental Reactor (ITER) research and the overall mission of delivering practical fusion energy. The FSP will address a rich set of scientific issues together with experimental programs, producing validated integrated physics results. This is very well aligned with the mission of the ITER Organization to coordinate with its members the integrated modeling and control of fusion plasmas, including benchmarking and validation activities. (1). Initial FSP research will focus on two critical Integrated Science Application (ISA) areas: ISA1, the plasma edge; and ISA2, whole device modeling (WDM) including disruption avoidance. The first of these problems involves the narrow plasma boundary layer and its complex interactions with the plasma core and the surrounding material wall. The second requires development of a computationally tractable, but comprehensive model that describes all equilibrium and dynamic processes at a sufficient level of detail to provide useful prediction of the temporal evolution of fusion plasma experiments. The initial driver for the whole device model will be prediction and avoidance of discharge-terminating disruptions, especially at high performance, which are a critical

Mode-selective symmetry control for indirect-drive inertial confinement fusion hohlraums

International Nuclear Information System (INIS)

Vesey, R. A.; Slutz, S. A.; Herrmann, M. C.; Mehlhorn, T. A.; Campbell, R. B.

2008-01-01

Achieving a high degree of radiation symmetry is a critical feature of target designs for indirect-drive inertial confinement fusion. Typically, the radiation flux incident on the capsule is required to be uniform to 1% or better. It is generally possible to design a hohlraum that provides low values of higher-order asymmetry (Legendre mode P 10 and above) due to geometric averaging effects. Because low-order intrinsic asymmetry (e.g., Legendre modes P 2 and P 4 ) are less strongly reduced by geometric averaging alone, the development of innovative control techniques has been an active area of research in the inertial fusion community over the years. Shields placed inside the hohlraum are one example of a technique that has often been proposed and incorporated into hohlraum target designs. Simple mathematical considerations are presented indicating that radiation shields may be designed to specifically tune lower-order modes (e.g., P 4 ) without deleterious effects on the higher order modes. Two-dimensional view factor and radiation-hydrodynamics simulations confirm these results and support such a path to achieving a highly symmetric x-ray flux. The term ''mode-selective'' is used because these shields, essentially ring structures offset from the capsule, are designed to affect only a specific Legendre mode (or multiple modes) of interest

Human Factors and Data Fusion as Part of Control Systems Resilience

Energy Technology Data Exchange (ETDEWEB)

David I. Gertman

2009-05-01

Human performance and human decision making is counted upon as a crucial aspect of overall system resilience. Advanced control systems have the potential to provide operators and asset owners a wide range of data, deployed at different levels that can be used to support operator situation awareness. However, the sheer amount of data available can make it challenging for operators to assimilate information and respond appropriately. This paper reviews some of the challenges and issues associated with providing operators with actionable state awareness and argues for the over arching importance of integrating human factors as part of intelligent control systems design and implementation. It is argued that system resilience is improved by implementing human factors in operations and maintenance. This paper also introduces issues associated with resilience and data fusion and highlights areas in which human factors including field studies hold promise.

Abstracts of the 23rd European physical society conference on controlled fusion and plasma physics

Energy Technology Data Exchange (ETDEWEB)

Goutych, I F; Gresillon, D; Sitenko, A G

1997-12-31

This document contains the abstracts of the invited and contributed papers presented at 23 EPS conference on controlled fusion and plasma physics. The main contents are: tokamaks, stellarators; alternative magnetic confinement; plasma edge physics; plasma heating and current drive; plasma diagnostics; basic collisionless plasma physics; high intensity laser produced plasmas and inertial confinement; low-temperature plasmas.

Abstracts of the 23rd European physical society conference on controlled fusion and plasma physics

International Nuclear Information System (INIS)

Goutych, I.F.; Gresillon, D.; Sitenko, A.G.

1996-01-01

This document contains the abstracts of the invited and contributed papers presented at 23 EPS conference on controlled fusion and plasma physics. The main contents are: tokamaks, stellarators; alternative magnetic confinement; plasma edge physics; plasma heating and current drive; plasma diagnostics; basic collisionless plasma physics; high intensity laser produced plasmas and inertial confinement; low-temperature plasmas

Energy from inertial fusion

International Nuclear Information System (INIS)

1995-03-01

This book contains 22 articles on inertial fusion energy (IFE) research and development written in the framework of an international collaboration of authors under the guidance of an advisory group on inertial fusion energy set up in 1991 to advise the IAEA. It describes the actual scientific, engineering and technological developments in the field of inertial confinement fusion (ICF). It also identifies ways in which international co-operation in ICF could be stimulated. The book is intended for a large audience and provides an introduction to inertial fusion energy and an overview of the various technologies needed for IFE power plants to be developed. It contains chapters on (i) the fundamentals of IFE; (ii) inertial confinement target physics; (iii) IFE power plant design principles (requirements for power plant drivers, solid state laser drivers, gas laser drivers, heavy ion drivers, and light ion drivers, target fabrication and positioning, reaction chamber systems, power generation and conditioning and radiation control, materials management and target materials recovery), (iv) special design issues (radiation damage in structural materials, induced radioactivity, laser driver- reaction chamber interfaces, ion beam driver-reaction chamber interfaces), (v) inertial fusion energy development strategy, (vi) safety and environmental impact, (vii) economics and other figures of merit; (viii) other uses of inertial fusion (both those involving and not involving implosions); and (ix) international activities. Refs, figs and tabs

Contributions to the 20. EPS conference on controlled fusion and plasma physics

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-07-15

The Conference covers research on different aspects of plasma physics and fusion technology, like technical aspects of Tokamak devices; plasma instabilities and impurities, development and testing of materials for fusion reactors etc.

Progress of laser fusion at Lawrence Livermore Laboratory

Energy Technology Data Exchange (ETDEWEB)

Ahlstrom, H G [California Univ., Livermore (USA). Lawrence Livermore Lab.

1979-01-01

Inertial confinement fusion is the present and future source of energy in our universe. Derivatives, such as solar, geothermal, wind, and biomass are proposed as future substitutes for possible fuel sources. All of these possible sources of energy while they may be considered to be renewable do not fulfill the single most important criteria of being unlimited. Fuel reserves of more than 100 billion years are accepted as 'unlimited'. The understanding of fusion has many 'fathers', Bethe, Teller and many others, it has also has proponents (too many to list) as the world's energy supply. This author hopes that this Program's efforts will contribute positively to the advance to the time when fusion energy will positively contribute to the energy supply for mankind. Controlled fusion is judged by us to be the world's most challenging technological problem. The potential benefit to mankind of an unlimited source of energy and thus a higher standard of living make the acceptance of this challenge worth our while. There are many dedicated scientists working on controlled fusion to make this dream a reality. Magnetic and inertial fusion are in a horse race that must not be allowed to falter or to be cancelled. Fusion is the future of the world and one of these approaches to fusion is vital to our future generations.

Progress of laser fusion at Lawrence Livermore Laboratory

International Nuclear Information System (INIS)

Ahlstrom, H.G.

1979-01-01

Inertial confinement fusion is the present and future source of energy in our universe. Derivatives, such as solar, geothermal, wind, and biomass are proposed as future substitutes for possible fuel sources. All of these possible sources of energy while they may be considered to be renewable do not fulfill the single most important criteria of being unlimited. Fuel reserves of more than 100 billion years are accepted as 'unlimited'. The understanding of fusion has many 'fathers', Bethe, Teller and many others, it has also has proponents (too many to list) as the world's energy supply. This author hopes that this Program's efforts will contribute positively to the advance to the time when fusion energy will positively contribute to the energy supply for mankind. Controlled fusion is judged by us to be the world's most challenging technological problem. The potential benefit to mankind of an unlimited source of energy and thus a higher standard of living make the acceptance of this challenge worth our while. There are many dedicated scientists working on controlled fusion to make this dream a reality. Magnetic and inertial fusion are in a horse race that must not be allowed to falter or to be cancelled. Fusion is the future of the world and one of these approaches to fusion is vital to our future generations

EURATOM-CEA association. Controlled fusion. Management committee nr 79. Activity report. National collaborations (Universities and CNRS). November 2007 - October 2005

International Nuclear Information System (INIS)

Garbet, X.; Benkadda, S.; Ottaviani, M.; Escande, D.; Blum, J.; Brenier, Y.; Lutjens, H.; Ghendrih, Ph.; Lima, R.; Bertrand, P.; Firpo, M.C.

2005-12-01

This publication presents several research projects on controlled fusion lead in collaboration by CNRS and academic teams. The general framework of these projects concerns theoretical developments in gyro-kinetics, transport and equilibrium to develop the required tools for the modelling of fusing plasmas. It comprises a study of characterisation and control of turbulent transport in tokamak plasmas, a study on the magnetic self-organisation of fusing plasmas, a gyro-kinetic modelling of tokamak plasmas, a study of identification and optimal control of plasma equilibrium in a tokamak, a gyrokinetic approach to the Vlasov equation, a study of the linear and non linear dynamics of instability modes in a tokamak plasma by using the model of extended magnetohydrodynamics, a study of the control of turbulence in magnetic fusion plasmas, and a study of the non linear regime of the n=1, m=1 mode

Prospects for Tokamak Fusion Reactors

International Nuclear Information System (INIS)

Sheffield, J.; Galambos, J.

1995-01-01

This paper first reviews briefly the status and plans for research in magnetic fusion energy and discusses the prospects for the tokamak magnetic configuration to be the basis for a fusion power plant. Good progress has been made in achieving fusion reactor-level, deuterium-tritium (D-T) plasmas with the production of significant fusion power in the Joint European Torus (up to 2 MW) and the Tokamak Fusion Test Reactor (up to 10 MW) tokamaks. Advances on the technologies of heating, fueling, diagnostics, and materials supported these achievements. The successes have led to the initiation of the design phases of two tokamaks, the International Thermonuclear Experimental Reactor (ITER) and the US Toroidal Physics Experiment (TPX). ITER will demonstrate the controlled ignition and extended bum of D-T plasmas with steady state as an ultimate goal. ITER will further demonstrate technologies essential to a power plant in an integrated system and perform integrated testing of the high heat flux and nuclear components required to use fusion energy for practical purposes. TPX will complement ITER by testing advanced modes of steady-state plasma operation that, coupled with the developments in ITER, will lead to an optimized demonstration power plant

The analysis of senior high school students' physics HOTS in Bantul District measured using PhysReMChoTHOTS

Science.gov (United States)

Istiyono, Edi

2017-08-01

The purpose of this research is to describe the results of higher order thinking skills in physics (PhysHOTS) measurement including: (1) percentage of PhysHOTS level and (2) percentage of the domination of response in the category of students in each analyzing, evaluating, and creating skill. There were 404 10th grade students in Bantul District as the respondents of this research. The instrument used for measurement was PhysReMChoTHOTS. It was divided into two sets consisting of 44 items and including 8 anchor items stated valid by a Physicist, Physics Education Expert, and Physics Education Measurement Expert. The instrument was fit to PCM. The reliability coefficient of this test is 0.71, while the difficulty index of the items ranges from -0.61 to 0.51. The results of the measurement show that: (1) The percentage of each category of PhysHOTS for the 10th grade students in Bantul District for the very low, low, medium, high, and very high category is 4.75 %, 40.30 %, 33.45 %, 19.50 %, and 2.00 %, respectively; and (2) The order in analyzing skills, starts from the weakest, is attributing, differentiating and organizing. The order in evaluating skills, starts from the weakest, is critiquing and checking. Meanwhile, the order in creating skills, starts from the weakest, is producing, planning, and generating.

Sensor fusion for mobile robot navigation

International Nuclear Information System (INIS)

Kam, M.; Zhu, X.; Kalata, P.

1997-01-01

The authors review techniques for sensor fusion in robot navigation, emphasizing algorithms for self-location. These find use when the sensor suite of a mobile robot comprises several different sensors, some complementary and some redundant. Integrating the sensor readings, the robot seeks to accomplish tasks such as constructing a map of its environment, locating itself in that map, and recognizing objects that should be avoided or sought. The review describes integration techniques in two categories: low-level fusion is used for direct integration of sensory data, resulting in parameter and state estimates; high-level fusion is used for indirect integration of sensory data in hierarchical architectures, through command arbitration and integration of control signals suggested by different modules. The review provides an arsenal of tools for addressing this (rather ill-posed) problem in machine intelligence, including Kalman filtering, rule-based techniques, behavior based algorithms and approaches that borrow from information theory, Dempster-Shafer reasoning, fuzzy logic and neural networks. It points to several further-research needs, including: robustness of decision rules; simultaneous consideration of self-location, motion planning, motion control and vehicle dynamics; the effect of sensor placement and attention focusing on sensor fusion; and adaptation of techniques from biological sensor fusion

Nuclear fusion: power for the next century

International Nuclear Information System (INIS)

1980-05-01

The basis of fusion reactions is outlined, with special reference to deuterium and tritium (from lithium, by neutron reaction) as reactants, and the state of research worldwide is indicated. The problems inherent in fusion reactions are discussed, plasma is defined, and the steps to be taken to generate electricity from controlled nuclear fusion are stated. Methods of plasma heating and plasma confinement are considered, leading to a description of the tokamak plasma confinement system. Devices under construction include the JET (Joint European Torus) Undertaking in the UK. Plans and possibilities for fusion reactors are discussed. (U.K.)

Nuclear Fusion Research Understanding Plasma-Surface Interactions

CERN Document Server

Clark, Robert E.H

2005-01-01

It became clear in the early days of fusion research that the effects of the containment vessel (erosion of "impurities") degrade the overall fusion plasma performance. Progress in controlled nuclear fusion research over the last decade has led to magnetically confined plasmas that, in turn, are sufficiently powerful to damage the vessel structures over its lifetime. This book reviews current understanding and concepts to deal with this remaining critical design issue for fusion reactors. It reviews both progress and open questions, largely in terms of available and sought-after plasma-surface interaction data and atomic/molecular data related to these "plasma edge" issues.

Controlled Nuclear Fusion by Magnetic Confinement and ITER

CERN Document Server

CERN. Geneva. Audiovisual Unit; Alvarez-Gaumé, Luís

2005-01-01

For may years harnessing fusion energy was considered the final solution to the world's energy crisis. ITER is the last step in the elusive quest. This presentation will provide in its various acientific, technological and political aspects.

Studies on the kinetics of muon catalyzed fusion in the HT mixture with very low tritium concentration

International Nuclear Information System (INIS)

Motlagh, S. N. H.

2007-01-01

.Int.School of Phys.'Enrico Fermi', Course C.3, Monastero, 23 June -3 July 1387.p.417. 11. J.N.bachcall, M.H.Pinsonneault, Rev.Mod.Phys.64, 885(1992). 12.M.Arnould,M.Forestini,Nuclear Astrophysics,Proc.of the Rhird Int.Summer School ,La Rabida, Huelve,Spain,Research Reportsin Physics(Springer -Verlag,1988),p.48. 13. F.J.Hartmann et al.,Muon Catal.Fusion 2,53(1988) . 14. P.Baumann et al., Muon Catal.Fusion 5, 87(1990); F.J.Hartmann et al., Hyp.Int.82,259(1993)., 15-F.Mulhauser et al.Pysc.Rev A 53, 3069(1996). 16- F.Mulhauser et al, Hyp.Int.119,35(1999). 17-V.R.Bom et al., Hypfine Interact.118, 103(1999)

Fusion energy

International Nuclear Information System (INIS)

Gross, R.A.

1984-01-01

This textbook covers the physics and technology upon which future fusion power reactors will be based. It reviews the history of fusion, reaction physics, plasma physics, heating, and confinement. Descriptions of commercial plants and design concepts are included. Topics covered include: fusion reactions and fuel resources; reaction rates; ignition, and confinement; basic plasma directory; Tokamak confinement physics; fusion technology; STARFIRE: A commercial Tokamak fusion power plant. MARS: A tandem-mirror fusion power plant; and other fusion reactor concepts

Suppression of hydrogenated carbon film deposition by scavenger techniques and their application to the tritium inventory control of fusion devices

International Nuclear Information System (INIS)

Tabares, F.L.; Tafalla, D.; Tanarro, I.; Herrero, V.J.; Islyaikin, A.; Maffiotte, C.

2002-01-01

The well-known radical and ion scavenger techniques of application in amorphous hydrogenated carbon film deposition studies are investigated in relation to the mechanism of tritium and deuterium co-deposition in carbon-dominated fusion devices. A particularly successful scheme results from the injection of nitrogen into methane/hydrogen plasmas for conditions close to those prevailing in the divertor region of present fusion devices. A complete suppression of the a-C : H film deposition has been achieved for N 2 /CH 4 ratios close to one in methane (5%)/hydrogen DC plasma. The implications of these findings in the tritium retention control in future fusion reactors are addressed. (author). Letter-to-the-editor

Fusion Power Program biannual progress report, April-September 1979

International Nuclear Information System (INIS)

1980-02-01

This biannual report summarizes the Argonne National Laboratory work performed for the Office of Fusion Energy during the April-September 1979 quarter in the following research and development areas: materials; energy storage and transfer; tritium containment, recovery and control; advanced reactor design; atomic data; reactor safety; fusion-fission hybrid systems; alternate applications of fusion energy; and other work related to fusion power. Separate abstracts were prepared for three sections

ORNL's Controlled Fusion Atomic Data Center

International Nuclear Information System (INIS)

Barnett, C.F.; Gregory, D.C.

1983-01-01

The Data Center maintains a detailed bibliography of atomic data measurements and calculations for processes of interest to the fusion community. One hundred nineteen journals are regularly searched for papers of interest, including back issues to 1950. Entries are categorized by author, process, reactants, energy range, and theory/experiment. Complete bibliographies have been published since 1978 and a computerized data retrieval system is available. In addition, an updated and extended multi-volume critical compilation of cross sections (the ORNL Redbooks) is under way

An in-flight radiography platform to measure hydrodynamic instability growth in inertial confinement fusion capsules at the National Ignition Facility

Energy Technology Data Exchange (ETDEWEB)

Raman, K. S.; Smalyuk, V. A.; Casey, D. T.; Haan, S. W.; Hurricane, O. A.; Kroll, J. J.; Peterson, J. L.; Remington, B. A.; Robey, H. F.; Clark, D. S.; Hammel, B. A.; Landen, O. L.; Marinak, M. M.; Munro, D. H.; Salmonson, J. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Hoover, D. E.; Nikroo, A. [General Atomics, San Diego, California 92121 (United States); Peterson, K. J. [Sandia National Laboratory, Albuquerque, New Mexico 87125 (United States)

2014-07-15

A new in-flight radiography platform has been established at the National Ignition Facility (NIF) to measure Rayleigh–Taylor and Richtmyer–Meshkov instability growth in inertial confinement fusion capsules. The platform has been tested up to a convergence ratio of 4. An experimental campaign is underway to measure the growth of pre-imposed sinusoidal modulations of the capsule surface, as a function of wavelength, for a pair of ignition-relevant laser drives: a “low-foot” drive representative of what was fielded during the National Ignition Campaign (NIC) [Edwards et al., Phys. Plasmas 20, 070501 (2013)] and the new high-foot [Dittrich et al., Phys. Rev. Lett. 112, 055002 (2014); Park et al., Phys. Rev. Lett. 112, 055001 (2014)] pulse shape, for which the predicted instability growth is much lower. We present measurements of Legendre modes 30, 60, and 90 for the NIC-type, low-foot, drive, and modes 60 and 90 for the high-foot drive. The measured growth is consistent with model predictions, including much less growth for the high-foot drive, demonstrating the instability mitigation aspect of this new pulse shape. We present the design of the platform in detail and discuss the implications of the data it generates for the on-going ignition effort at NIF.

An in-flight radiography platform to measure hydrodynamic instability growth in inertial confinement fusion capsules at the National Ignition Facility

International Nuclear Information System (INIS)

Raman, K. S.; Smalyuk, V. A.; Casey, D. T.; Haan, S. W.; Hurricane, O. A.; Kroll, J. J.; Peterson, J. L.; Remington, B. A.; Robey, H. F.; Clark, D. S.; Hammel, B. A.; Landen, O. L.; Marinak, M. M.; Munro, D. H.; Salmonson, J.; Hoover, D. E.; Nikroo, A.; Peterson, K. J.

2014-01-01

A new in-flight radiography platform has been established at the National Ignition Facility (NIF) to measure Rayleigh–Taylor and Richtmyer–Meshkov instability growth in inertial confinement fusion capsules. The platform has been tested up to a convergence ratio of 4. An experimental campaign is underway to measure the growth of pre-imposed sinusoidal modulations of the capsule surface, as a function of wavelength, for a pair of ignition-relevant laser drives: a “low-foot” drive representative of what was fielded during the National Ignition Campaign (NIC) [Edwards et al., Phys. Plasmas 20, 070501 (2013)] and the new high-foot [Dittrich et al., Phys. Rev. Lett. 112, 055002 (2014); Park et al., Phys. Rev. Lett. 112, 055001 (2014)] pulse shape, for which the predicted instability growth is much lower. We present measurements of Legendre modes 30, 60, and 90 for the NIC-type, low-foot, drive, and modes 60 and 90 for the high-foot drive. The measured growth is consistent with model predictions, including much less growth for the high-foot drive, demonstrating the instability mitigation aspect of this new pulse shape. We present the design of the platform in detail and discuss the implications of the data it generates for the on-going ignition effort at NIF

Annual progress report 1993. Work in controlled thermonuclear fusion research performed in the fusion research unit under the contract of association between Euratom and Risoe National Laboratory

International Nuclear Information System (INIS)

1994-09-01

The programme of the Research Unit of the Fusion Association Euratom-Risoe National Laboratory covers work in fusion plasma physics and in fusion technology. The fusion plasma physics group has activities within (a) studies of nonlinear dynamical processes in magnetized plasmas, (b) development of pellet injectors for fusion experiments, and (c) development of diagnostics for fusion plasmas. The activities in technology cover radiation damage of fusion reactor materials. A summary of the activities in 1993 is presented. (au) (4 tabs., 21 ills., 64 refs.)

Osteoclast Fusion

DEFF Research Database (Denmark)

Marie Julie Møller, Anaïs; Delaissé, Jean-Marie; Søe, Kent

2017-01-01

on the nuclearity of fusion partners. While CD47 promotes cell fusions involving mono-nucleated pre-osteoclasts, syncytin-1 promotes fusion of two multi-nucleated osteoclasts, but also reduces the number of fusions between mono-nucleated pre-osteoclasts. Furthermore, CD47 seems to mediate fusion mostly through...... individual fusion events using time-lapse and antagonists of CD47 and syncytin-1. All time-lapse recordings have been studied by two independent observers. A total of 1808 fusion events were analyzed. The present study shows that CD47 and syncytin-1 have different roles in osteoclast fusion depending...... broad contact surfaces between the partners' cell membrane while syncytin-1 mediate fusion through phagocytic-cup like structure. J. Cell. Physiol. 9999: 1-8, 2016. © 2016 Wiley Periodicals, Inc....

Progress towards a high-gain and robust target design for heavy ion fusion

Energy Technology Data Exchange (ETDEWEB)

Henestroza, Enrique; Grant Logan, B. [Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

2012-07-15

Recently [E. Henestroza et al., Phys. Plasmas 18, 032702 (2011)], a new inertial-fusion target configuration, the X-target, using one-sided axial illumination has been explored. This class of target uses annular and solid-profile heavy ion beams to compress and ignite deuterium-tritium (DT) fuel that fills the interior of metal cases that have side-view cross sections in the shape of an 'X.' X-targets using all-DT-filled metal cases imploded by three annular ion beams resulted in fuel densities of {approx}50 g/cm{sup 3} at peak compression, and fusion gains of {approx}50, comparable to heavy ion driven hohlraum targets [D. A. Callahan-Miller and M. Tabak, Phys. Plasmas 7, 2083 (2000)]. This paper discusses updated X-target configurations that incorporate inside the case a propellant (plastic) and a pusher (aluminum) surrounding the DT fuel. The updated configurations are capable of assembling higher fuel areal densities {approx}2 g/cm{sup 2} using two annular beams to implode the target to peak DT densities {approx}100 g/cm{sup 3}, followed by a fast-ignition solid ion beam which heats the high-density fuel to thermonuclear temperatures in {approx}200 ps to start the burn propagation, obtaining gains of {approx}300. These targets have been modeled using the radiation-hydrodynamics code HYDRA [M. M. Marinak et al., Phys. Plasmas 8, 2275 (2001)] in two- and three- dimensions to study the properties of the implosion as well as the ignition and burn propagation phases. At typical Eulerian mesh resolutions of a few microns, the aluminum-DT interface shows negligible Rayleigh-Taylor (RT) and Richtmyer-Meshkov instability growth; also, the shear flow of the DT fuel as it slides along the metal X-target walls, which drives the RT and Kelvin Helmholtz instabilities, does not have a major effect on the burning rate. An analytic estimate of the RT instability process at the Al-DT interface shows that the aluminum spikes generated during the pusher deceleration phase

Diagnostics considerations for the inertial confinement approach to controlled thermonuclear fusion power production

International Nuclear Information System (INIS)

Wood, L.

1978-01-01

It is concluded that although the challenges facing diagnosticians working on the inertial confinement approach to controlled fusion are large and varied, the means potentially available to meet them are more than adequate. No new instrumentation fields need be opened; rather, substantial extensions of those already being explored by workers in ICF will suffice. Also, large contributions may be expected from other technological applications thrusts, as well as from the general, currently rapid advance of the entire physical technology base

Long-term planning frame of controlled fusion research in the Federal Republic of Germany and within the scope of EURATOM

International Nuclear Information System (INIS)

1989-01-01

Current R and D activities in the field of controlled nuclear fusion are investigating physics and technological problems rather than economic efficiency aspects of future fusion reactor systems. The report in hand compares the long-term plans and programmes set up on the European level with other countries' programmes, explains the international cooperative framework and activities, and goes into details of the Federal German research programme. Aspects of safety and environmental impacts are discussed. (HP) [de

Utilization of a Network of Small Magnetic Confinement Fusion Devices for Mainstream Fusion Research. Report of a Coordinated Research Project 2011–2016

International Nuclear Information System (INIS)

2016-12-01

The IAEA actively promotes the development of controlled fusion as a source of energy. Through its coordinated research activities, the IAEA helps Member States to exchange and establish scientific and technical knowledge required for the design, construction and operation of a fusion reactor. Due to their compactness, flexibility and low operation costs, small fusion devices are a great resource for supporting and accelerating the development of mainstream fusion research on large fusion devices such as the International Thermonuclear Experimental Reactor. They play an important role in investigating the physics of controlled fusion, developing innovative technologies and diagnostics, testing new materials, training highly qualified personnel for larger fusion facilities, and supporting educational programmes for young scientists. This publication reports on the research work accomplished within the framework of the Coordinated Research Project (CRP) on Utilization of the Network of Small Magnetic Confinement Fusion Devices for Mainstream Fusion Research, organized and conducted by the IAEA in 2011–2016. The CRP has contributed to the coordination of a network of research institutions, thereby enhancing international collaboration through scientific visits, joint experiments and the exchange of information and equipment. A total of 16 institutions and 14 devices from 13 Member States participated in this CRP (Belgium, Bulgaria, Canada, China, Costa Rica, the Czech Republic, the Islamic Republic of Iran, Kazakhstan, Pakistan, Portugal, the Russian Federation, Ukraine and the United Kingdom).

Plasma physics and controlled nuclear fusion research 1994. V. 3. Proceedings of the fifteenth international conference

International Nuclear Information System (INIS)

1996-01-01

This is the third volume of the proceedings of the 15th International Atomic Energy Agency Conference on Plasma Physics and Controlled Nuclear Fusion Research held in Seville, Spain, from 26 September - 1 October 1994. Contained in it are 29 papers on inertial confinement and 46 papers on magnetic confinement. Refs, figs, tabs

State of controlled nuclear fusion research

International Nuclear Information System (INIS)

Rodrigo, A.B.

1978-04-01

The development of a commercial fusion reactor requires an adequate solution to the problems of heating and confinement of the nuclear fuel, as well as a considerable effort in materials technology and reactor engineering. A general discussion is presented of the status of the research connected with the most advanced concepts, indicating in each case the present situation and the main problems that must be solved to meet the requeriments estimated for power reactors. In particular, the laser-inertial concept is reviewed in detail. (author) [es

Material for fusion reactor

International Nuclear Information System (INIS)

Abhishek, Anuj; Ranjan, Prem

2011-01-01

To make nuclear fusion power a reality, the scientists are working restlessly to find the materials which can confine the power generated by the fusion of two atomic nuclei. A little success in this field has been achieved, though there are still miles to go. Fusion reaction is a special kind of reaction which must occur at very high density and temperature to develop extremely large amount of energy, which is very hard to control and confine within using the present techniques. As a whole it requires the physical condition that rarely exists on the earth to carry out in an efficient manner. As per the growing demand and present scenario of the world energy, scientists are working round the clock to make effective fusion reactions to real. In this paper the work presently going on is considered in this regard. The progress of the Joint European Torus 2010, ITER 2005, HiPER and minor works have been studied to make the paper more object oriented. A detailed study of the technological and material requirement has been discussed in the paper and a possible suggestion is provided to make a contribution in the field of building first ever nuclear fusion reactor

Control of activation levels to simplify waste management of fusion reactor ferritic steel components

International Nuclear Information System (INIS)

Wiffen, F.W.; Santoro, R.T.

1983-01-01

Activation characteristics of a material for service in the neutron flux of a fusion reactor first wall fall into three areas: waste management, reactor maintenance and repair, and safety. Of these, the waste management area is the most likely to impact the public acceptance of fusion reactors for power generation. The decay of the activity in steels within tens of years could lead to simplified waste disposal or possibly even to materials recycle. Whether or not these can be achieved will be controlled by (1) selection of alloying elements, (2) control of critical impurity elements, and (3) control of cross contamination from other reactor components. Several criteria can be used to judge the acceptability of potential alloying elements in iron, and to define the limits on content of critical impurity elements. One approach is to select and limit alloying additions on the basis of the activity. If material recycle is a goal, N, Al, Ni, Cu, Nb, and Mo must be excluded. If simplified waste storage by shallow land burial is the goal, regulations limit the concentration of only a few isotopes. For first-wall material that will be exposed to 9 MW-y/m 2 service, allowable initial concentration limits include (in at. ppM) Ni < 20,000; Mo < 3650; N < 3650, Cu < 2400; and Nb < 1.0. The other constituent elements of ferritic steels will not be limited. Possible substitutes for the molybdenum normally used to strengthen the steels include W, Ta, Ti, and V

Design of Lamifuse: a randomised, multi-centre controlled trial comparing laminectomy without or with dorsal fusion for cervical myeloradiculopathy

Directory of Open Access Journals (Sweden)

Grotenhuis J André

2007-11-01

Full Text Available Abstract Background laminectomy is a valuable surgical treatment for some patients with a cervical radiculomyelopathy due to cervical spinal stenosis. More recently attention has been given to motion of the spinal cord over spondylotic spurs as a cause of myelopathic changes. Immobilisation by fusion could have a positive effect on the recovery of myelopathic signs or changes. This has never been investigated in a prospective, randomised trial. Lamifuse is an acronyme for laminectomy and fusion. Methods/Design Lamifuse is a multicentre, randomised controlled trial comparing laminectomy with and without fusion in patients with a symptomatic cervical canal stenosis. The study population will be enrolled from patients that are 60 years or older with myelopathic signs and/or symptoms due to a cervical canal stenosis. A kyphotis shape of the cervical spine is an exclusion criterium. Each treatment arm needs 30 patients. Discussion This study will contribute to the discussion whether additional fusion after a cervical laminectomy results in a better clinical outcome. ISRCT number ISRCTN72800446

Confusion about nuclear fusion: a false report is laid bare

International Nuclear Information System (INIS)

Hintsches, E.

1983-01-01

The author discusses the inaccurate and precipitate news of alleged successful controlled nuclear fusion in the Tokamak Fusion Test Reactor at Princeton University. The later modified published report indicated that in a first test, fractional second operation had produced plasma gas temperature of 100,000 0 C whereas 100 million degrees C is necessary for hydrogen nuclear fusion. Also power generation from nuclear fusion is still a long term goal. Problems of nuclear fusion are very briefly mentioned, and an impression of the Tokamak Fusion Test Reactor is illustrated. (H.V.H.)

Control and data management for a large fusion laser

International Nuclear Information System (INIS)

Davis, J.W.; Holloway, F.W.

1975-01-01

SHIVA is a powerful (10-kJ 25 TW) neodymium glass laser system to be used (in 1977) for target irradiation in fusion research. SHIVA is also a development project in that it is pushing the state of the art in laser and optical technology. The present design calls for 20 parallel laser amplification chains whose light output is pointed and focused at a small (100 μ) target within a chamber from semi-equally spaced three-dimensional directions. It is probable that SHIVA will be upgraded to as many as 42 chains in the next few years. Each chain of SHIVA contains 7 high energy laser amplifiers and perhaps 20 other major optical components, many of which send and receive control and measurement information. Again future expansion may add additional elements. Each chain has also associated 10 gimbal or translation motions for beam assignment from the oscillator onto the target

Quantum propagator approach to heavy-ion fusion

International Nuclear Information System (INIS)

Bao, J.D.

2002-01-01

The real-time path integral propagator approach is used to study the fusion probability of massive nuclei including quantum effect. An analytical expression of the probability to pass over barrier of an inverted harmonic potential is obtained, in which both height and curvature of the barrier are controlled by the neck degree of freedom. The fusion probability of three systems in central collision as a function of the center of mass energy are calculated and compared to experimental results. It is shown that the quantum fluctuation enhances the fusion probability at low energies, and the neck fluctuation makes the slope of the fusion probability curve become flatter. (author)

New trends in fusion research

CERN Multimedia

CERN. Geneva

2004-01-01

The efforts of the international fusion community aim at demonstrating the scientific feasibility of thermonuclear fusion energy power plants. Understanding the behavior of burning plasmas, i.e. plasmas with strong self-heating, represents a primary scientific challenge for fusion research and a new science frontier. Although integrated studies will only be possible, in new, dedicated experimental facilities, such as the International Tokamak Experimental Reactor (ITER), present devices can address specific issues in regimes relevant to burning plasmas. Among these are an improvement of plasma performance via a reduction of the energy and particle transport, an optimization of the path to ignition or to sustained burn using additional heating and a control of plasma-wall interaction and energy and particle exhaust. These lectures address recent advances in plasma science and technology that are relevant to the development of fusion energy. Mention will be made of the inertial confinement line of research, but...

Tritium accountancy in fusion systems

Energy Technology Data Exchange (ETDEWEB)

Klein, J.E.; Clark, E.A.; Harvel, C.D.; Farmer, D.A.; Tovo, L.L.; Poore, A.S. [Savannah River National Laboratory, Aiken, SC (United States); Moore, M.L. [Savannah River Nuclear Solutions, Aiken, SC (United States)

2015-03-15

The US Department of Energy (DOE) has clearly defined requirements for nuclear material control and accountability (MCA) of tritium whereas the International Atomic Energy Agency (IAEA) does not since tritium is not a fissile material. MCA requirements are expected for tritium fusion machines and will be dictated by the host country or regulatory body where the machine is operated. Material Balance Areas (MBA) are defined to aid in the tracking and reporting of nuclear material movements and inventories. Material sub-accounts (MSA) are established along with key measurement points (KMP) to further subdivide a MBA to localize and minimize uncertainties in the inventory difference (ID) calculations for tritium accountancy. Fusion systems try to minimize tritium inventory which may require continuous movement of material through the MSA. The ability of making meaningful measurements of these material transfers is described in terms of establishing the MSA structure to perform and reconcile ID calculations. For fusion machines, changes to the traditional ID equation will be discussed which includes breeding, burn-up, and retention of tritium in the fusion device. The concept of 'net' tritium quantities consumed or lost in fusion devices is described in terms of inventory taking strategies and how it is used to track the accumulation of tritium in components or fusion machines. (authors)

Fusion

CERN Document Server

Mahaffey, James A

2012-01-01

As energy problems of the world grow, work toward fusion power continues at a greater pace than ever before. The topic of fusion is one that is often met with the most recognition and interest in the nuclear power arena. Written in clear and jargon-free prose, Fusion explores the big bang of creation to the blackout death of worn-out stars. A brief history of fusion research, beginning with the first tentative theories in the early 20th century, is also discussed, as well as the race for fusion power. This brand-new, full-color resource examines the various programs currently being funded or p

Response to "Comment on `Solitonic and chaotic behaviors for the nonlinear dust-acoustic waves in a magnetized dusty plasma'" [Phys. Plasmas 24, 094701 (2017)

Science.gov (United States)

Zhen, Hui-Ling; Tian, Bo; Xie, Xi-Yang; Wu, Xiao-Yu; Wen, Xiao-Yong

2018-02-01

On our previous construction [H. L. Zhen et al., Phys. Plasmas 23, 052301 (2016)] of the soliton solutions of a model describing the dynamics of the dust particles in a weakly ionized, collisional dusty plasma comprised of the negatively charged cold dust particles, hot ions, hot electrons, and stationary neutrals in the presence of an external static magnetic field, Ali et al. [Phys. Plasmas 24, 094701 (2017)] have commented that there exists a different form of Eq. (4) from that shown in Zhen et al. [Phys. Plasmas 23, 052301 (2016)] and that certain interesting phenomena with the dust neutral collision frequency ν0>0 are ignored in Zhen et al. [Phys. Plasmas 23, 052301 (2016)]. In this Reply, according to the transformation given by the Ali et al. [Phys. Plasmas 24, 094701 (2017)] comment, we present some one-, two-, and N-soliton solutions which have not been obtained in the Ali et al. [Phys. Plasmas 24, 094701 (2017)] comment. We point out that our previous solutions in Zhen et al. [Phys. Plasmas 23, 052301 (2016)] are still valid because of the similarity between the two dispersion relations of previous solutions in Zhen et al. [Phys. Plasmas 23, 052301 (2016)] and the solutions presented in this Reply. Based on our soliton solutions in this Reply, it is found that the soliton amplitude is inversely related to Zd and B0, but positively related to md and α, where α refers to the coefficient of the nonlinear term, Zd and md are the charge number and mass of a dust particle, respectively, B0 represents the strength of the external static magnetic field. We also find that the two solitons are always in parallel during the propagation.

Comment on “Temperature dependence of atomic vibrations in mono-layer graphene” [J. Appl. Phys. 118, 074302 (2015)

International Nuclear Information System (INIS)

Susi, T.; Kotakoski, J.

2016-01-01

In an interesting recent study [Allen et al., J. Appl. Phys. 118, 074302 (2015)] (see also their Erratum [Allen et al., J. Appl. Phys. 118, 159902 (2015)]), Allen and co-workers measured the mean square amplitudes of graphene lattice vibrations between 100 and 1300 K and used a simplified theoretical approximation for the acoustic phonon modes to evaluate the maximum phonon wavelengths supported by the lattice. By fitting their data using the smallest wave-vector as the fitting parameter, they found this to be significantly smaller than the physical size of the graphene crystallites

On the Potential Role of Species Separation in DT Fuels on Implosion Performance

Science.gov (United States)

Amendt, Peter; Bellei, Claudio; Wilks, Scott; Haines, Malcolm; Casey, Dan; Li, C. K.; Petrasso, Richard

2012-10-01

The measurement of strong, self-generated electric fields (1-10 GVolts/m) in imploding capsules [1], their attribution to polarized (plasma) shock fronts [2], and the identification of plasma-enhanced binary species diffusion from barodiffusion and electrodiffusion [3] have led to a growing interest in the potential role of species separation in inertial-confinement-fusion (ICF) thermonuclear fuels. The potential for anomalous heating from transient frictional or resistive drag between D and T across a finite thickness shock front will be assessed and applied towards ignition thresholds and understanding some outstanding anomalies in the Omega implosion database.[4pt] [1] J.R. Rygg et al., Science 319, 1223 (2008); C.K. Li et al., Phys. Rev. Lett. 100, 225001 (2008).[0pt] [2] P.A. Amendt, J.L. Milovich, S.C. Wilks, C.K. Li, R.D. Petrasso and F.H. S'eguin, Plasma Phys. Control. Fusion 51, 124048 (2009).[0pt] [3] P. Amendt, C. Bellei and S.C. Wilks, Phys. Rev. Lett. (to appear).

Control characteristics of cryogenic distillation column with a feedback stream for fusion reactor

International Nuclear Information System (INIS)

Yamanishi, Toshihiko; Okuno, Kenji

1997-01-01

The control characteristics of the cryogenic distillation column with a feedback stream have been discussed based on computer simulation results. This column plays an important role in fusion reactor. A new control system was proposed from the simulation results. The flow rate of top product is determined from the composition and flow rate of a main feed stream by a feedforward control loop. The flow rates of the feedback stream and vapor stream within the column are proportionally changed with a corresponding change of feed flow rate. The flow rate of vapor stream within the column is further adjusted to maintain product purity by a feedback control loop. The proposed system can control the product purity for a large fluctuation of feed composition, a change of feed flow rate, and an increase or decrease of the number of total theoretical stages of the column. The control system should be designed for each column by considering its operating conditions and function. The present study gives us a basic procedure for the design method of the control system of the cryogenic distillation column. (author)

Tools and methods for implementing the control systems on the Mirror Fusion Test Facility

International Nuclear Information System (INIS)

Minor, E.G.; Labiak, W.G.

1981-01-01

Installation of the major hardware subsystems for MFTF is nearing completion. These subsystems include the Fusion Chamber System, the eighty KV Neutral Beam System, the Superconducting Magnet System, and the Personnel Safety System. The Local Controls group has undertaken a uniform aproach to implementing the control systems for all of these hardware subsystems. This approach has two major aspects: (1) to provide a stand-alone computer control system with a remote, portable terminal so that computer control can be provided at the site of the hardware for initial testing, (2) to provide hardware simulators so that the complicated MFTF computer control system can be tested independent of the hardware. The software and hardware tools which were developed to carry out this plan will be described. Our experiences with bringing up subsystems containing up to 900 separate channels of control and status will also be described

Roentgenographic findings following anterior cervical fusion

Energy Technology Data Exchange (ETDEWEB)

Gore, D R; Gardner, G M; Sepic, S B; Murray, M P

1986-10-01

We reviewed the pre- and postoperative lateral cervical roentgenograms in 90 patients who had anterior fusions and compared their findings with age and sex-matched people without neck problems. The average interval from surgery to review was 5 years. Preoperatively, all patients had a higher incidence of degenerative spondylosis at the levels to be fused than their asymptomatic counterparts. Postoperatively, there was no difference in the incidence of degenerative change between the operated and the control group at the levels above and below the fusion with the exception of anterior osteophyte formation which was more frequent in those with fusions.

Thinking about the cold fusion fever

International Nuclear Information System (INIS)

Kitsunezaki, Akio

1989-01-01

The excitement since March 23 on cold fusion seems to be unprecedented evidence that the people of the world are waiting for fusion power with much enthusiasm. Cold fusion is really a surprise because it does not need high temperature and because it seems to be easy to enlarge the test tube into a useful power source if the claim by Professors Pons and Fleischmann at the University of Utah are true. The second announcement of cold fusion came from the Brigham Young University, also in the state of Utah, by Professor Jones, but his report was totally different from that given by Pons and Fleischmann. From the beginning of the 'fever', physicists have been very skeptical about cold fusion. Most of the critics and criticisms are targeted on Pons and Fleischmann rather than Jones, because not only was their paper poor but also their statements have not been scientific. They insisted that the heat came from fusion reaction, but without any scientific proof. They had not carried out the basic control experiment by running the same test with ordinary water instead of heavy water. A meeting on cold fusion was held at JAERI on May 15. At the end of the meeting, the some 260 attendants knew that cold fusion was not conceivable with the current scientific knowledge. (N.K.)

2003 activity report of the development and research line in controlled thermonuclear fusion of the Plasma Associated Laboratory

International Nuclear Information System (INIS)

Ludwig, Gerson Otto

2004-01-01

This document represents the 2003 activity report of the development and research line in controlled thermonuclear fusion of the Plasma Associated Laboratory - Brazil, approaching the areas of toroidal systems for magnetic confinement, plasma heating, current generation and high temperature plasma diagnostic

FRIENDLY regulates mitochondrial distribution, fusion, and quality control in Arabidopsis.

Science.gov (United States)

El Zawily, Amr M; Schwarzländer, Markus; Finkemeier, Iris; Johnston, Iain G; Benamar, Abdelilah; Cao, Yongguo; Gissot, Clémence; Meyer, Andreas J; Wilson, Ken; Datla, Raju; Macherel, David; Jones, Nick S; Logan, David C

2014-10-01

Mitochondria are defining components of most eukaryotes. However, higher plant mitochondria differ biochemically, morphologically, and dynamically from those in other eukaryotes. FRIENDLY, a member of the CLUSTERED MITOCHONDRIA superfamily, is conserved among eukaryotes and is required for correct distribution of mitochondria within the cell. We sought to understand how disruption of FRIENDLY function in Arabidopsis (Arabidopsis thaliana) leads to mitochondrial clustering and the effects of this aberrant chondriome on cell and whole-plant physiology. We present evidence for a role of FRIENDLY in mediating intermitochondrial association, which is a necessary prelude to mitochondrial fusion. We demonstrate that disruption of mitochondrial association, motility, and chondriome structure in friendly affects mitochondrial quality control and leads to mitochondrial stress, cell death, and strong growth phenotypes. © 2014 American Society of Plant Biologists. All Rights Reserved.

Mitochondrial fusion is increased by the nuclear coactivator PGC-1beta.

Directory of Open Access Journals (Sweden)

Marc Liesa

Full Text Available There is no evidence to date on whether transcriptional regulators are able to shift the balance between mitochondrial fusion and fission events through selective control of gene expression.Here, we demonstrate that reduced mitochondrial size observed in knock-out mice for the transcriptional regulator PGC-1beta is associated with a selective reduction in Mitofusin 2 (Mfn2 expression, a mitochondrial fusion protein. This decrease in Mfn2 is specific since expression of the remaining components of mitochondrial fusion and fission machinery were not affected. Furthermore, PGC-1beta increases mitochondrial fusion and elongates mitochondrial tubules. This PGC-1beta-induced elongation specifically requires Mfn2 as this process is absent in Mfn2-ablated cells. Finally, we show that PGC-1beta increases Mfn2 promoter activity and transcription by coactivating the nuclear receptor Estrogen Related Receptor alpha (ERRalpha.Taken together, our data reveal a novel mechanism by which mammalian cells control mitochondrial fusion. In addition, we describe a novel role of PGC-1beta in mitochondrial physiology, namely the control of mitochondrial fusion mainly through Mfn2.

Thermoplastic fusion bonding using a pressure-assisted boiling point control system.

Science.gov (United States)

Park, Taehyun; Song, In-Hyouk; Park, Daniel S; You, Byoung Hee; Murphy, Michael C

2012-08-21

A novel thermoplastic fusion bonding method using a pressure-assisted boiling point (PABP) control system was developed to apply precise temperatures and pressures during bonding. Hot embossed polymethyl methacrylate (PMMA) components containing microchannels were sealed using the PABP system. Very low aspect ratio structures (AR = 1/100, 10 μm in depth and 1000 μm in width) were successfully sealed without collapse or deformation. The integrity and strength of the bonds on the sealed PMMA devices were evaluated using leakage and rupture tests; no leaks were detected and failure during the rupture tests occurred at pressures greater than 496 kPa. The PABP system was used to seal 3D shaped flexible PMMA devices successfully.

Muon nuclear fusion and low temperature nuclear fusion

International Nuclear Information System (INIS)

Nagamine, Kanetada

1990-01-01

Low temperature (or normal temperature) nuclear fusion is one of the phenomena causing nuclear fusion without requiring high temperature. In thermal nuclear fusion, the Coulomb barrier is overcome with the help of thermal energy, but in the low temperature nuclear fusion, the Coulomb barrier is neutralized by the introduction of the particles having larger mass than electrons and negative charges, at this time, if two nuclei can approach to the distance of 10 -13 cm in the neutral state, the occurrence of nuclear fusion reaction is expected. As the mass of the particles is heavier, the neutral region is smaller, and nuclear fusion is easy to occur. The particles to meet this purpose are the electrons within substances and muons. The research on muon nuclear fusion became suddenly active in the latter half of 1970s, the cause of which was the discovery of the fact that the formation of muons occurs resonantly rapidly in D-T and D-D systems. Muons are the unstable elementary particles having the life of 2.2 μs, and they can have positive and negative charges. In the muon catalyzed fusion, the muons with negative charge take part. The principle of the muon catalyzed fusion, its present status and future perspective, and the present status of low temperature nuclear fusion are reported. (K.I.)

High-energy fusion: A quest for a simple, small and environmentally acceptable colliding-beam fusion power source

International Nuclear Information System (INIS)

Maglich, B.

1978-01-01

Fusion goals should be lowered for a speedier research and development of a less ambitious but a workable 'low-gain fusion power amplifier', based on proven technologies and concepts. The aim of the Migma Program of Controlled Fusion is a small (10-15 liters) fusion power source based on colliding beams instead of plasma or laser heating. Its scientific and technological 'philosophy' is radically different from that of the governmental fusion programs of the USA and USSR. Migmacell uses radiation-free fuels, ('advanced fuels'), rather than tritium. Economic projections show that such a smaller power cell can be econonomically competitive in spite of its low power gain, because it can be mass produced. Power stations could be made either large or small and the power transmission and distribution pattern in the nation would change. An interspersion of energy resources would result. Minifusion opens the possibility to smaller countries (and medium size institutions of large countries), for participation in fusion research; this resource of research talent is presently excluded from fusion by the high cost of the mainline governmental research (over $ 200 million for one experimental fusion device, as compared to $ 1 million for migmacell). The time-scale for obtaining experimental results is reduced from decades to years. Experimental accomplishments to date and the further research needed, are presented. (orig.) [de

How much laser power can propagate through fusion plasma?

International Nuclear Information System (INIS)

Lushnikov, Pavel M; Rose, Harvey A

2006-01-01

Propagation of intense laser beams is crucial for inertial confinement fusion, which requires precise beam control to achieve the compression and heating necessary to ignite the fusion reaction. The National Ignition Facility (NIF), where fusion will be attempted, is now under construction. Control of intense beam propagation may be ruined by laser beam self-focusing. We have identified the maximum laser beam power that can propagate through fusion plasma without significant self-focusing and have found excellent agreement with recent experimental data. This maximum is determined by the collective forward stimulated Brillouin scattering instability which suggests a way to increase the maximum power by appropriate choice of plasma composition with implication for NIF designs. Our theory also leads to the prediction of anti-correlation between beam spray and backscatter and therefore raises the possibility of indirect control of backscatter through manipulation of plasma ionization state or acoustic damping. We find a simple expression for laser intensity at onset of enhanced beam angular divergence (beam spray)

Controlled fusion and plasma physics

International Nuclear Information System (INIS)

Bickerton, R.J.

1991-01-01

On JET results were presented on additional heating power, on a recently discovered regime of enhanced pellet performance (PEP), on low-density H-mode plasma confinement with hot ions, bounds on very high electric currents by material limiters, the first experiments on lower hybrid current drive, on the L-H transition threshold dependence on the direction of the gradient-B drift, and on alpha-particle physics issues. The TFTR presentations focused on transport. Particle loss ramifications of the toroidal Alfven eigenmodes were found to be small, while their threshold of excitation is lower than theoretically predicted. On DIII-D a scaling study of transport with gyroradius as the only variable was reported, with approximately Bohm scaling emerging; but the effective heat diffusivity scaling could not be established due to profile consistency effects. While beta-limit investigations with DIII-D generally confirm the ideal, MHD limit found by Troyon, evidence of a reduction of the accessible range for the internal inductance with the safety factor seems to favour current-density control in a steady-state D-T burner. Onset of strongly sheared poloidal rotation in a thin layer during the L-H mode transition was experimentally shown, while a new, so-called VH (''very high'') confinement mode was discovered by boronization of the wall. The JT-90 tokamak has recently been upgraded to JT-60-U. Presentations by the ASDEX team summarized the lack of agreement with theory of L-mode confinement. With TEXTOR, an improved mode (I-mode) of confinement was found by boronization. Finally, reviews are included on the status of impurity transport and helium removal in tokamaks, on stellarators, alternative magnetic confinement systems, inertial confinement, and non-fusion plasma physics. 2 tabs

Annual report of the Summit Members' Working Group on Controlled Thermonuclear Fusion (Fusin Working Group (FWG))

International Nuclear Information System (INIS)

1987-04-01

The Summit Members' Working Group on Controlled Thermonuclear Fusion [Fusion Working Group (FWG)] was established in 1983 in response to the Declaration of the Heads of State and Government at the Versailles Economic Summit meeting of 1982, and in response to the subsequent report of the Working Group in Technology, Growth and Employment (TGE) as endorsed at the Williamsburg Summit meeting, 1983. This document contains the complete written record of each of the three FWG meetings which include the minutes, lists of attendees, agendas, statements, and summary conclusions as well as the full reports of the Technical Working Party. In addition, there is a pertinent exchange of correspondence between FWG members on the role of the Technical Working Party and a requested background paper on the modalities associated with a possible future ETR project

Tritium management in fusion reactors

International Nuclear Information System (INIS)

Galloway, T.R.

1978-05-01

This is a review paper covering the key environmental and safety issues and how they have been handled in the various magnetic and inertial confinement concepts and reference designs. The issues treated include: tritium accident analyses, tritium process control, occupational safety, HTO formation rate from the gas-phase, disposal of tritium contaminated wastes, and environmental impact--each covering the Joint European Tokamak (J.E.T. experiment), Tokamak Fusion Test Reactor (TFTR), Russian T-20, The Next Step (TNS) designs by Westinghouse/ORNL and General Atomic/ANL, the ANL and ORNL EPR's, the G.A. Doublet Demonstration Reactor, the Italian Fintor-D and the ORNL Demo Studies. There are also the following full scale plant reference designs: UWMAK-III, LASL's Theta Pinch Reactor Design (RTPR), Mirror Fusion Reactor (MFR), Tandem Mirror Reactor (TMR), and the Mirror Hybrid Reactor (MHR). There are four laser device breakeven experiments, SHIVA-NOVA, LLL reference designs, ORNL Laser Fusion power plant, the German ''Saturn,'' and LLL's Laser Fusion EPR I and II

Optimization of the fission--fusion hybrid concept

International Nuclear Information System (INIS)

Saltmarsh, M.J.; Grimes, W.R.; Santoro, R.T.

1979-04-01

One of the potentially attractive applications of controlled thermonuclear fusion is the fission--fusion hybrid concept. In this report we examine the possible role of the hybrid as a fissile fuel producer. We parameterize the advantages of the concept in terms of the performance of the fusion device and the breeding blanket and discuss some of the more troublesome features of existing design studies. The analysis suggests that hybrids based on deuterium--tritium (D--T) fusion devices are unlikely to be economically attractive and that they present formidable blanket technology problems. We suggest an alternative approach based on a semicatalyzed deuterium--deuterium (D--D) fusion reactor and a molten salt blanket. This concept is shown to emphasize the desirable features of the hybrid, to have considerably greater economic potential, and to mitigate many of the disadvantages of D--T-based systems

Nuclear fusion - Inexhaustible source of energy for tomorrow

International Nuclear Information System (INIS)

Leiser, M.; Demchenko, V.

1989-09-01

The purpose of this paper is to provide a general description of nuclear fusion as an energy option for the future and to clarify to some extent the various issues - scientific, technological, economic and environmental - which are likely to be relevant to controlled thermonuclear fusion. Section 1 describes the world energy problem and some advantages of nuclear fusion compared to other energy options. Sections 2 and 3 describe the fundamentals of fusion energy, plasma confinement, heating and technological aspects of fusion researches. Some plasma confinement schemes (tokamak, stellarator, inertial confinement fusion) are described. The main experimental results and parameter devices are cited to illustrate the state of the art as of 1989. Various engineering problems associated with reactor design, magnetic systems, materials, plasma purity, fueling, blankets, environment, economics and safety are discussed. A description of both bilateral and multilateral efforts in fusion research under the auspices of the IAEA is presented in Section 4. (author). 11 refs, 4 figs, 1 tab

Survey of tritium wastes and effluents in near-term fusion-research facilities

International Nuclear Information System (INIS)

Bickford, W.E.; Dingee, D.A.; Willingham, C.E.

1981-08-01

The use of tritium control technology in near-term research facilities has been studied for both the magnetic and inertial confinement fusion programs. This study focused on routine generation of tritium wastes and effluents, with little referene to accidents or facility decommissioning. This report serves as an independent review of the effectiveness of planned control technology and radiological hazards associated with operation. The facilities examined for the magnetic fusion program included Fusion Materials Irradiation Testing Facility (FMIT), Tritium Systems Test Assembly (TSTA), and Tokamak Fusion Test Reactor (TFTR) in the magnetic fusion program, while NOVA and Antares facilities were examined for the inertial confinement program

ENEA-Frascati inertial confinement fusion: Multi-channel digitizer control, acquisition and analysis system

Energy Technology Data Exchange (ETDEWEB)

Caruso, A.; Strangio, C.; Elman, G.; Hugh, J. Mc; Rogers, G.; Pastina, E.; Raimondi, F.; Umbro, A.

1991-09-01

The ICF (Inertial Confinement Fusion) data acquisition and analysis system described in this paper incorporates digitizer channels, signal switching, an instrument controller, a graphic hardcopy unit, laser printer and software. The digitizers, signal switching and instrument controller are standard components appropriate to acquire the single fast shot signals (rise-time: from about 100 picoseconds to nanoseconds). The input signals are switched to the digitizers through the TSI-8150 test system interface by TSS40 switch controller cards and TSS46 18GHz microwave switches. Graphic hardcopy is accomplished using either a 4693PX colour hardcopy unit or a laser printer connected through a printer spooler/multiplexer. The software is based on an existing package from Ressler called RAI/DAC reviewed by Fus-Inerz and Tektronix-Italy to define the modifications needed for data acquisition and handling. The adopted software solution is based on an IBM PC compatible instrument controller running software developed by Ressler Associates.

New concepts for controlled fusion reactor blanket design

International Nuclear Information System (INIS)

Conn, R.W.; Kulcinski, G.L.; Avci, H.; El-Maghrabi, M.

1975-01-01

Several new concepts for fusion reactor blanket design based on the idea of shifting, or tailoring, the neutron spectrum incident on the first structural wall are presented. The spectral shifter is a nonstructural element which can be made of graphite, silicon carbide, or three dimensionally woven carbon fibers (and containing other materials as appropriate) placed between the neutron source and the first structural wall. The softened neutron spectrum incident on the structural components leads to lower gas production and atom displacement rates than in more standard fusion blanket designs. In turn, this results in longer anticipated lifetimes for the structural materials and can significantly reduce radioactivity and afterheat levels. In addition, the neutron spectrum in the first structural wall can be made to approach the flux shape in fast breeder reactors. Such spectral softening means that existing radiation facilities may be more profitably used to provide relevant materials radiation damage data for the structural materials in these fusion blanket designs. This general class of blanket concepts are referred to as internal spectral shifter and energy converter, or ISSEC concepts. These specific design concepts fall into three main categories: ISSEC/EB concepts based on utilizing existing designs which breed tritium behind the first structural wall; ISSEC/IB concepts based on breeding tritium inside the first vacuum wall; and ISSEC/Bu concepts based on using boron, carbon, and perhaps, beryllium to obtain an energy multiplier and converter design that does not attempt to breed tritium or utilize lithium. The detailed analyses relate specifically to the nuclear performance of ISSEC systems and to a discussion of materials radiation damage problems in the structural material.(U.S.)

Color Multifocus Image Fusion Using Empirical Mode Decomposition

Directory of Open Access Journals (Sweden)

S. Savić

2013-11-01

Full Text Available In this paper, a recently proposed grayscale multifocus image fusion method based on the first level of Empirical Mode Decomposition (EMD has been extended to color images. In addition, this paper deals with low contrast multifocus image fusion. The major advantages of the proposed methods are simplicity, absence of artifacts and control of contrast, while this isn’t the case with other pyramidal multifocus fusion methods. The efficiency of the proposed method is tested subjectively and with a vector gradient based objective measure, that is proposed in this paper for multifocus color image fusion. Subjective analysis performed on a multifocus image dataset has shown its superiority to the existing EMD and DWT based methods. The objective measures of grayscale and color image fusion show significantly better scores for this method than for the classic complex EMD fusion method.

Challenges of nuclear fusion

International Nuclear Information System (INIS)

Kunkel, W.B.

1987-01-01

After 30 years of research and development in many countries, the magnetic confinement fusion experiments finally seem to be getting close to the original first goal: the point of ''scientific break-even''. Plans are being made for a generation of experiments and tests with actual controlled thermonuclear fusion conditions. Therefore engineers and material scientists are hard at work to develop the required technology. In this paper the principal elements of a generic fusion reactor are described briefly to introduce the reader to the nature of the problems at hand. The main portion of the presentation summarises the recent advances made in this field and discusses the major issues that still need to be addressed in regard to materials and technology for fusion power. Specific examples are the problems of the first wall and other components that come into direct contact with the plasma, where both lifetime and plasma contamination are matters of concern. Equally challenging are the demands on structural materials and on the magnetic-field coils, particularly in connection with the neutron-radiation environment of fusion reactors. Finally, the role of ceramics must be considered, both for insulators and for fuel breeding purposes. It is evident that we still have a formidable task before us, but at this point none of the problems seem to be insoluble. (author)

Fusion technology: The Iter fusion experiment

International Nuclear Information System (INIS)

Dietz, K.J.

1994-01-01

Plans for the Iter international fusion experiment, in which the European Union, Japan, Canada, Russia, Sweden, Switzerland, and the USA cooperate, were begun in 1985, and construction work started in early 1994. These activities serve for the preparation of the design and construction documents for a research reactor in which a stable fusion plasma is to be generated. This is to be the basis for the construction of a fusion reactor for electricity generation. Preparatory work was performed in the Tokamak experiments with JET and TFTR. The fusion power of 1.5 GW will be attained, thus enabling Iter to keep a deuterium-tritium plasma burning. (orig.) [de

Fusion fuel cycle: material requirements and potential effluents

International Nuclear Information System (INIS)

Teofilo, V.L.; Bickford, W.E.; Long, L.W.; Price, B.A.; Mellinger, P.J.; Willingham, C.E.; Young, J.K.

1980-10-01

Environmental effluents that may be associated with the fusion fuel cycle are identified. Existing standards for controlling their release are summarized and anticipated regulatory changes are identified. The ability of existing and planned environmental control technology to limit effluent releases to acceptable levels is evaluated. Reference tokamak fusion system concepts are described and the principal materials required of the associated fuel cycle are analyzed. These materials include the fusion fuels deuterium and tritium; helium, which is used as a coolant for both the blanket and superconducting magnets; lithium and beryllium used in the blanket; and niobium used in the magnets. The chemical and physical processes used to prepare these materials are also described

Fusion fuel cycle: material requirements and potential effluents

Energy Technology Data Exchange (ETDEWEB)

Teofilo, V.L.; Bickford, W.E.; Long, L.W.; Price, B.A.; Mellinger, P.J.; Willingham, C.E.; Young, J.K.

1980-10-01

Environmental effluents that may be associated with the fusion fuel cycle are identified. Existing standards for controlling their release are summarized and anticipated regulatory changes are identified. The ability of existing and planned environmental control technology to limit effluent releases to acceptable levels is evaluated. Reference tokamak fusion system concepts are described and the principal materials required of the associated fuel cycle are analyzed. These materials include the fusion fuels deuterium and tritium; helium, which is used as a coolant for both the blanket and superconducting magnets; lithium and beryllium used in the blanket; and niobium used in the magnets. The chemical and physical processes used to prepare these materials are also described.

Comment on 'Instability of the Shukla mode in a dusty plasma containing equilibrium density and magnetic field inhomogeneities' [Phys. Plasmas 11, 1732 (2004)] and 'New resonance and cut-off for low-frequency electromagnetic waves in dusty magnetoplasmas' [Phys. Plasmas 11, 2307 (2004)

International Nuclear Information System (INIS)

Rudakov, Leonid

2004-01-01

It is shown that the oscillation named by Shukla as the 'Shukla mode' is well known in the plasma physics literature as the magnetic drift wave. In addition, the instability of these modes in a cold plasma as claimed by Shukla et al. [Phys. Plasmas 11, 1732 (2004)] does not exist and is due to a mathematical error in their analysis. Also the 'new' resonance and new cutoff frequencies claimed by Shukla et al. and Mamum et al. [Phys Plasmas 11, 2307 (2004)] have been known in the published literature for decades

Conflicting views on the membrane fusion machinery and the fusion pore

DEFF Research Database (Denmark)

Sørensen, Jakob B

2009-01-01

of the assembly of the fusogenic SNARE-complex. Here, I review conflicting views on the function of the core fusion machinery consisting of the SNAREs, Munc18, complexin, and synaptotagmin. Munc18 controls docking of vesicles to the plasma membrane and initial SNARE-complex assembly, whereas complexin...

EURATOM strategy towards fusion energy

International Nuclear Information System (INIS)

Varandas, C.

2007-01-01

Research and development (Research and Development) activities in controlled thermonuclear fusion have been carried out since the 60's of the last century aiming at providing a new clean, powerful, practically inexhaustive, safe, environmentally friend and economically attractive energy source for the sustainable development of our society.The EURATOM Fusion Programme (EFP) has the leadership of the magnetic confinement Research and Development activities due to the excellent results obtained on JET and other specialized devices, such as ASDEX-Upgrade, TORE SUPRA, FTU, TCV, TEXTOR, CASTOR, ISTTOK, MAST, TJ-II, W7-X, RFX and EXTRAP. JET is the largest tokamak in operation and the single device that can use deuterium and tritium mixes. It has produced 16 MW of fusion power, during 3 seconds, with an energy amplification of 0.6. The next steps of the EFP strategy towards fusion energy are ITER complemented by a vigorous Accompanying Programme, DEMO and a prototype of a fusion power plant. ITER, the first experimental fusion reactor, is a large-scale project (35-year duration, 10000 MEuros budget), developed in the frame of a very broad international collaboration, involving EURATOM, Japan, Russia Federation, United States of America, Korea, China and India. ITER has two main objectives: (i) to prove the scientific and technical viability of fusion energy by producing 500 MW, during 300 seconds and a energy amplification between 10 and 20; and (ii) to test the simultaneous and integrated operation of the technologies needed for a fusion reactor. The Accompanying Programme aims to prepare the ITER scientific exploitation and the DEMO design, including the development of the International Fusion Materials Irradiation Facility (IFMIF). A substantial part of this programme will be carried out in the frame of the Broader Approach, an agreement signed by EURATOM and Japan. The main goal of DEMO is to produce electricity, during a long time, from nuclear fusion reactions. The

Higher order corrections to mixed QCD-EW contributions to Higgs boson production in gluon fusion

Science.gov (United States)

Bonetti, Marco; Melnikov, Kirill; Tancredi, Lorenzo

2018-03-01

We present an estimate of the next-to-leading-order (NLO) QCD corrections to mixed QCD-electroweak contributions to the Higgs boson production cross section in gluon fusion, combining the recently computed three-loop virtual corrections and the approximate treatment of real emission in the soft approximation. We find that the NLO QCD corrections to the mixed QCD-electroweak contributions are nearly identical to NLO QCD corrections to QCD Higgs production. Our result confirms an earlier estimate of these O (α αs2) effects by Anastasiou et al. [J. High Energy Phys. 04 (2009) 003, 10.1088/1126-6708/2009/04/003] and provides further support for the factorization approximation of QCD and electroweak corrections.

Plasma nuclear fusion method

International Nuclear Information System (INIS)

Yamazaki, Shunpei; Miyanaga, Shoji; Wakaizumi, Kazuhiro; Takemura, Yasuhiko.

1990-01-01

Nuclear fusion reactions are attained by plasma gas phase reactions using magnetic fields and microwaves, and the degree of the reactions is controlled. That is, deuterium (D 2 ) is introduced into a plasma container by utilizing the resonance of microwaves capable of generating plasmas at high density higher by more than 10 - 10 3 times as compared with the high frequency and magnetic fields, and an electric energy is applied to convert gaseous D 2 into plasmas and nuclear fusion is conducted. Further, the deuterium ions in the plasmas are attracted to a surface of a material causing nuclear fusion under a negatively biased electric field from the outside (typically represented by Pd or Ti). Then, deuterium nuclei (d) or deuterium ions collide to the surface of the cathode on the side of palladium to conduct nuclear reaction at the surface or the inside (vicinity) thereof. However, a DC bias is applied as an external bias with the side of the palladium being negative. The cold nuclear fusion was demonstrated by placing a neutron counter in the vicinity of the container and confirming neutrons generated there. (I.S.)

Research programme on controlled thermonuclear fusion - Synthesis report 2010; Programme de recherche Fusion thermonucleaire controlee. Rapport de synthese 2010

Energy Technology Data Exchange (ETDEWEB)

Vaucher, C. [Secretariat d' Etat a l' education et a la recherche, Berne (Switzerland); Tran, M. Q.; Villard, L. [Swiss Federal Institute of Technology (EPFL), Lausanne (Switzerland); Marot, L. [University of Basel, Basel (Switzerland)

2011-07-01

Since 1978, research on thermonuclear fusion in Switzerland is closely related to the research programme of the European Atomic Energy Community (EURATOM). The Swiss projects tackle aspects of plasma physics and fusion technology. Switzerland participates to the construction and operation of the Joint European Torus (JET). The International Thermonuclear Experimental Reactor (ITER) is being built; the first plasma is expected in 2019. The 'Centre de Recherches en Physique des Plasmas' (CRPP) of the EPFL participates to EURATOM scientific and technological projects in magnetic confinement physics, through an experimental contribution (the Variable Configuration Tokamak, TCV) and theoretical studies. Thanks to the large flexibility of the TCV design and operation modus, plasmas of different shapes can be created and controlled, what is a very useful option to verify numerical simulation results. Besides, the injection of millimetre waves allows directing the injected power according to specific profiles. A configuration of type 'snowflakes' could be created, reducing the power deposition at the edge of the plasma. Theoretical studies on turbulence have improved the plasma stability in the TCV. For the first time in the world, TCV could reach a stable plasma, the plasma current being generated using the so-called 'bootstrap' phenomenon. Besides turbulence, studies were focused on heat and particle transport in tokamaks, on an analysis of the equilibrium and magneto-hydrodynamic stability of tokamaks and stellarators, on the application of radiofrequency waves and on the optimization of new confinement configurations. Experiments in the JET facility confirmed the numerical results of theoretical simulations. The TORPEX facility, which is simpler than TCV, allows high space-temporal resolution measurements for the study of turbulences and plasma threads ('blobs'). At the Paul Scherrer Institute (PSI), research topics include

EMP Fusion

OpenAIRE

KUNTAY, Isık

2010-01-01

This paper introduces a novel fusion scheme, called EMP Fusion, which has the promise of achieving breakeven and realizing commercial fusion power. The method is based on harnessing the power of an electromagnetic pulse generated by the now well-developed flux compression technology. The electromagnetic pulse acts as a means of both heating up the plasma and confining the plasma, eliminating intermediate steps. The EMP Fusion device is simpler compared to other fusion devices and this reduces...

Establishment of an Institute for Fusion Studies

International Nuclear Information System (INIS)

Hazeltine, R.D.

1992-07-01

The Institute for Fusion Studies is a national center for theoretical fusion plasma physics research. Its purposes are: (1) to conduct research on theoretical questions concerning the achievement of controlled fusion energy by means of magnetic confinement--including both fundamental problems of long-range significance, as well as shorter-term issues; (2) to serve as a center for information exchange, nationally and internationally, by hosting exchange visits, conferences, and workshops; (3) and to train students and postdoctoral research personnel for the fusion energy program and plasma physics research areas. The theoretical research results that are obtained by the Institute contribute mainly to the progress of national and international efforts in nuclear fusion research, whose goal is the development of fusion power.as a basic energy source. In addition to its primary focus on fusion physics, the Institute is also involved with research in related fields, such as advanced computing techniques, nonlinear dynamics, plasma astrophysics, and accelerator physics. The work of EFS scientists continued to receive national and international recognition. Numerous invited papers were given during the past year at workshops, conferences, and scientific meetings. Last year IFS scientists published 95 scientific articles in technical journals and monographs

TORFA - toroidal reactor for fusion applications

International Nuclear Information System (INIS)

Jassby, D.L.

1980-09-01

The near-term goal of the US controlled fusion program should be the development, for practical applications, of an intense, quasi-steady, reliable 14-MeV neutron source with an electrical utilization efficiency at least 10 times larger than the value characterizing beam/solid-target neutron generators. This report outlines a method for implementing that goal, based on tokamak fusion reactors featuring resistive toroidal-field coils designed for ease of demountability

Fusion technology 1998

International Nuclear Information System (INIS)

Beaumont, B.; Libeyre, P.; Gentile, B. de; Tonon, G.

1998-01-01

The Symposium On Fusion Technology (SOFT) is held every two years with the objective to set the stage for the exchange of information on the design, construction and operation of fusion experiments and on the technology which is being developed for the next step devices and fusion reactors. By decision of the International Organizing Committee, the 20. SOFT includes invited talks, and oral and poster contributions in the following topics: plasma facing components, plasma heating and current drive, plasma engineering and control, experimental systems and diagnostics, magnets and power supplies, fuel technologies, remote operation, blanket and shield technologies, safety and environment, and system engineering and future devices. This symposium differs from the previous ones of this series by the way the present proceedings are produced. In order to have the written material available to the participants and the community at the nearest to the conference event, the papers have been collected 2 months in advance and printed in the present books. The goal was to deliver them to each participant upon arrival to the conference centre. These books contain all the papers corresponding to poster presentation, and the abstracts of the oral contributions and invited papers. The papers corresponding to these presentations, both oral and invited, will be published in 1999, after a standard review process, in a supplement of Fusion Engineering and Design. (author)

iNR-PhysChem: a sequence-based predictor for identifying nuclear receptors and their subfamilies via physical-chemical property matrix.

Directory of Open Access Journals (Sweden)

Xuan Xiao

Full Text Available Nuclear receptors (NRs form a family of ligand-activated transcription factors that regulate a wide variety of biological processes, such as homeostasis, reproduction, development, and metabolism. Human genome contains 48 genes encoding NRs. These receptors have become one of the most important targets for therapeutic drug development. According to their different action mechanisms or functions, NRs have been classified into seven subfamilies. With the avalanche of protein sequences generated in the postgenomic age, we are facing the following challenging problems. Given an uncharacterized protein sequence, how can we identify whether it is a nuclear receptor? If it is, what subfamily it belongs to? To address these problems, we developed a predictor called iNR-PhysChem in which the protein samples were expressed by a novel mode of pseudo amino acid composition (PseAAC whose components were derived from a physical-chemical matrix via a series of auto-covariance and cross-covariance transformations. It was observed that the overall success rate achieved by iNR-PhysChem was over 98% in identifying NRs or non-NRs, and over 92% in identifying NRs among the following seven subfamilies: NR1--thyroid hormone like, NR2--HNF4-like, NR3--estrogen like, NR4--nerve growth factor IB-like, NR5--fushi tarazu-F1 like, NR6--germ cell nuclear factor like, and NR0--knirps like. These rates were derived by the jackknife tests on a stringent benchmark dataset in which none of protein sequences included has ≥60% pairwise sequence identity to any other in a same subset. As a user-friendly web-server, iNR-PhysChem is freely accessible to the public at either http://www.jci-bioinfo.cn/iNR-PhysChem or http://icpr.jci.edu.cn/bioinfo/iNR-PhysChem. Also a step-by-step guide is provided on how to use the web-server to get the desired results without the need to follow the complicated mathematics involved in developing the predictor. It is anticipated that iNR-PhysChem may

Comparison between measured and predicted turbulence frequency spectra in ITG and TEM regimes

NARCIS (Netherlands)

Citrin, J.; Arnichand, H.; Bernardo, J.; Bourdelle, C.; Garbet, X.; Jenko, F.; Hacquin, S.; Puschel, M. J.; Sabot, R.

2017-01-01

The observation of distinct peaks in tokamak core reflectometry measurements—named quasi-coherent-modes (QCMs)—are identified as a signature of trapped-electron-mode (TEM) turbulence (Arnichand et al 2016 Plasma Phys. Control. Fusion 58 014037). This phenomenon is investigated with detailed linear

Thermonuclear fusion

International Nuclear Information System (INIS)

Weisse, J.

2000-01-01

This document takes stock of the two ways of thermonuclear fusion research explored today: magnetic confinement fusion and inertial confinement fusion. The basic physical principles are recalled first: fundamental nuclear reactions, high temperatures, elementary properties of plasmas, ignition criterion, magnetic confinement (charged particle in a uniform magnetic field, confinement and Tokamak principle, heating of magnetized plasmas (ohmic, neutral particles, high frequency waves, other heating means), results obtained so far (scale laws and extrapolation of performances, tritium experiments, ITER project), inertial fusion (hot spot ignition, instabilities, results (Centurion-Halite program, laser experiments). The second part presents the fusion reactor and its associated technologies: principle (tritium production, heat source, neutron protection, tritium generation, materials), magnetic fusion (superconducting magnets, divertor (role, principle, realization), inertial fusion (energy vector, laser adaptation, particle beams, reaction chamber, stresses, chamber concepts (dry and wet walls, liquid walls), targets (fabrication, injection and pointing)). The third chapter concerns the socio-economic aspects of thermonuclear fusion: safety (normal operation and accidents, wastes), costs (costs structure and elementary comparison, ecological impact and external costs). (J.S.)

Cell fusion in osteoclasts plays a critical role in controlling bone mass and osteoblastic activity

International Nuclear Information System (INIS)

Iwasaki, Ryotaro; Ninomiya, Ken; Miyamoto, Kana; Suzuki, Toru; Sato, Yuiko

2008-01-01

The balance between osteoclast and osteoblast activity is central for maintaining the integrity of bone homeostasis. Here we show that mice lacking dendritic cell specific transmembrane protein (DC-STAMP), an essential molecule for osteoclast cell-cell fusion, exhibited impaired bone resorption and upregulation of bone formation by osteoblasts, which do not express DC-STAMP, which led to increased bone mass. On the contrary, DC-STAMP over-expressing transgenic (DC-STAMP-Tg) mice under the control of an actin promoter showed significantly accelerated cell-cell fusion of osteoclasts and bone resorption, with decreased osteoblastic activity and bone mass. Bone resorption and formation are known to be regulated in a coupled manner, whereas DC-STAMP regulates bone homeostasis in an un-coupled manner. Thus our results indicate that inhibition of a single molecule provides both decreased osteoclast activity and increased bone formation by osteoblasts, thereby increasing bone mass in an un-coupled and a tissue specific manner.

Introduction to the controlled nuclear fusion (magnetic containment systems)

International Nuclear Information System (INIS)

Cabrera, J.A.; Guasp, J.; Martin, R.

1975-01-01

The magnetic containment systems, their more important features, and their potentiality to became thermonuclear reactors is described. The work is based upon the first part of a set of lectures dedicated to Plasma and Fusion Physics. (author)

Synchronization in a PLC/VAX-based control and data-acquisition system of a nuclear-fusion experiment

International Nuclear Information System (INIS)

Schmidt, V.; Flor, G.; Hemming, O.N.; Luchetta, A.; Manduchi, G.; Vitturi, S.

1990-01-01

This paper describes the concept and implementation details of the synchronization mechanisms used in the control and data-acquisition system of the RFX (Reversed-Field Experiment) nuclear-fusion experimental device, at present under construction in Padova, Italy, within the framework of the co-ordinated nuclear-fusion research programme of the European Communities. The system employs industrial PLCs for the 'slow' control and monitoring functions, and a VAX-based CAMAC for the 'fast' functions of trigger-signal generation and data acquisition during the experiment pulses. All subsystems communicate via Ethernet, using compatible software protocols. The operational sequence of the complete system is governed by a single state machine implemented on a PLC-based supervisor system. Equivalent 'slave' state machines are implemented on all other subsystems (PLC- and VAX-based). These state machines are synchronized by means of the exchange of messages via Ethernet. This paper deals in detail with the following components which are involved in system synchronization: The Message Exchange System which implements the system-wide exchange of short messages; the Scheduler programs which implement the state machine on the various computing nodes, and which make use of the Message Exchange System. (orig.)

Progress in heavy ion fusion research

International Nuclear Information System (INIS)

Celata, C.M.; Bieniosek, F.M.; Henestroza, E.; Kwan, J.W.; Lee, E.P.; Logan, G.; Prost, L.; Seidl, P.A.; Vay, J.-L.; Waldron, W.L.; Yu, S.S.; Barnard, J.J.; Callahan, D.A.; Cohen, R.H.; Friedman, A.; Grote, D.P.; Lund, S.M.; Molvik, A.; Sharp, W.M.; Westenskow, G.

2003-01-01

The U.S. Heavy Ion Fusion program has recently commissioned several new experiments. In the High Current Experiment [P. A. Seidl et al., Laser Part. Beams 20, 435 (2003)], a single low-energy beam with driver-scale charge-per-unit-length and space-charge potential is being used to study the limits to transportable current posed by nonlinear fields and secondary atoms, ions, and electrons. The Neutralized Transport Experiment similarly employs a low-energy beam with driver-scale perveance to study final focus of high perveance beams and neutralization for transport in the target chamber. Other scaled experiments--the University of Maryland Electron Ring [P. G. O'Shea et al., accepted for publication in Laser Part. Beams] and the Paul Trap Simulator Experiment [R. C. Davidson, H. Qin, and G. Shvets, Phys. Plasmas 7, 1020 (2000)]--will provide fundamental physics results on processes with longer scale lengths. An experiment to test a new injector concept is also in the design stage. This paper will describe the goals and status of these experiments, as well as progress in theory and simulation. A proposed future proof-of-principle experiment, the Integrated Beam Experiment, will also be described

Fusion neutronics

CERN Document Server

Wu, Yican

2017-01-01

This book provides a systematic and comprehensive introduction to fusion neutronics, covering all key topics from the fundamental theories and methodologies, as well as a wide range of fusion system designs and experiments. It is the first-ever book focusing on the subject of fusion neutronics research. Compared with other nuclear devices such as fission reactors and accelerators, fusion systems are normally characterized by their complex geometry and nuclear physics, which entail new challenges for neutronics such as complicated modeling, deep penetration, low simulation efficiency, multi-physics coupling, etc. The book focuses on the neutronics characteristics of fusion systems and introduces a series of theories and methodologies that were developed to address the challenges of fusion neutronics, and which have since been widely applied all over the world. Further, it introduces readers to neutronics design’s unique principles and procedures, experimental methodologies and technologies for fusion systems...

High Level Information Fusion (HLIF) with nested fusion loops

Science.gov (United States)

Woodley, Robert; Gosnell, Michael; Fischer, Amber

2013-05-01

Situation modeling and threat prediction require higher levels of data fusion in order to provide actionable information. Beyond the sensor data and sources the analyst has access to, the use of out-sourced and re-sourced data is becoming common. Through the years, some common frameworks have emerged for dealing with information fusion—perhaps the most ubiquitous being the JDL Data Fusion Group and their initial 4-level data fusion model. Since these initial developments, numerous models of information fusion have emerged, hoping to better capture the human-centric process of data analyses within a machine-centric framework. 21st Century Systems, Inc. has developed Fusion with Uncertainty Reasoning using Nested Assessment Characterizer Elements (FURNACE) to address challenges of high level information fusion and handle bias, ambiguity, and uncertainty (BAU) for Situation Modeling, Threat Modeling, and Threat Prediction. It combines JDL fusion levels with nested fusion loops and state-of-the-art data reasoning. Initial research has shown that FURNACE is able to reduce BAU and improve the fusion process by allowing high level information fusion (HLIF) to affect lower levels without the double counting of information or other biasing issues. The initial FURNACE project was focused on the underlying algorithms to produce a fusion system able to handle BAU and repurposed data in a cohesive manner. FURNACE supports analyst's efforts to develop situation models, threat models, and threat predictions to increase situational awareness of the battlespace. FURNACE will not only revolutionize the military intelligence realm, but also benefit the larger homeland defense, law enforcement, and business intelligence markets.

Thermonuclear fusion: Current status and future prospects

International Nuclear Information System (INIS)

Bruhns, H.; Maisonnier, Ch.

1992-01-01

Thermonuclear Fusion holds great promises for becoming an important energy source for the future. Fusion research and development is undertaken in al major countries of the world. The European Community pursues fusion in a large programme which embraces all R and D in the field of magnetic confinement fusion in the Member States, and to which Sweden and Switzerland are fully associated. The long-term objective of the programme is the joint creation of safe, environmentally sound prototype reactors. The main R and D line of the Community Fusion Programme is fusion by toroidal magnetic confinement on the basis of the Tokamak concept. Some related concepts are also studied which possibly could offer advantages for a reactor, and keep-in-touch activities exist for other approaches. Several small and medium sized specialised devices in Associated Laboratories have been built by the Community Fusion Programme as well as the Joint European Torus (JET Joint Undertaking) which is the largest and the most successful fusion device in the world. Recently, fusion power in the megawatt range has been achieved in JET. The long timescale and the large effort needed for the development of fusion as an energy source have been important elements to foster international collaboration. Engineering Design Activities for an International Thermonuclear Experimental Reactor (ITER) are undertaken, under the auspices of the IAEA, by the European Community, Japan, the Russian Federation and the United States of America. The objective of ITER is to achieve self-sustained thermonuclear burn and its control under long-pulse operation and to provide basic data for the engineering of a demonstration fusion reactor. (author)

Muon-catalyzed fusion: A new direction in fusion research

International Nuclear Information System (INIS)

Jones, S.E.

1986-01-01

In four years of intensive research, muon-catalyzed fusion has been raised from the level of a scientific curiosity to a potential means of achieving clean fusion energy. This novel approach to fusion is based on the fact that a sub-atomic particle known as a ''muon'' can induce numerous energy-releasing fusion reactions without the need for high temperatures or plasmas. Thus, the muon serves as a catalyst to facilitate production for fusion energy. The success of the research effort stems from the recent discovery of resonances in the reaction cycle which make the muon-induced fusion process extremely efficient. Prior estimates were pessimistic in that only one fusion per muon was expected. In that case energy balance would be impossible since energy must be invested to generate the muons. However, recent work has gone approximately half-way to energy balance and further improvements are being worked on. There has been little time to assess the full implications of these discoveries. However, various ways to use muon-catalyzed fusion for electrical power production are now being explored

Muon-catalyzed fusion: a new direction in fusion research

International Nuclear Information System (INIS)

Jones, S.E.

1986-01-01

In four years of intensive research, muon-catalyzed fusion has been raised from the level of a scientific curiosity to a potential means of achieving clean fusion energy. This novel approach to fusion is based on the fact that a sub-atomic particle known as a ''muon'' can induce numerous energy-releasing fusion reactions without the need for high temperatures or plasmas. Thus, the muon serves as a catalyst to facilitate production for fusion energy. The success of the research effort stems from the recent discovery of resonances in the reaction cycle which make the muon-induced fusion process extremely efficient. Prior estimates were pessimistic in that only one fusion per muon was expected. In that case energy balance would be impossible since energy must be invested to generate the muons. However, recent work has gone approximately half-way to energy balance and further improvements are being worked on. There has been little time to assess the full implications of these discoveries. However, various ways to use muon-catalyzed fusion for electrical power production are now being explored

Fusion breeder

International Nuclear Information System (INIS)

Moir, R.W.

1982-01-01

The fusion breeder is a fusion reactor designed with special blankets to maximize the transmutation by 14 MeV neutrons of uranium-238 to plutonium or thorium to uranium-233 for use as a fuel for fission reactors. Breeding fissile fuels has not been a goal of the US fusion energy program. This paper suggests it is time for a policy change to make the fusion breeder a goal of the US fusion program and the US nuclear energy program. The purpose of this paper is to suggest this policy change be made and tell why it should be made, and to outline specific research and development goals so that the fusion breeder will be developed in time to meet fissile fuel needs

Research program. Controlled thermonuclear fusion. Synthesis report 2014; Programme de recherche. Fusion thermonucléaire contrôlée -- Rapport de synthèse 2014

Energy Technology Data Exchange (ETDEWEB)

Villard, L. [Swiss Federal Institute of Technology (EPFL), Center for Research In Plasma Physics, CRPP, Lausanne (Switzerland); Marot, L. [University of Basel, Department of Physics, Basel (Switzerland); Fiocco, D. [Secrétariat d' Etat à la formation., à la recherche et à l' innovation, SEFRI, Berne (Switzerland)

2015-07-01

In 1961, 3 years after the 2{sup nd} International Conference on Peaceful Use of Nuclear Energy, the Research Centre on Plasma Physics (CRPP) was created as a department of the Federal Institute of Technology (EPFL) in Lausanne (Switzerland). From 1979, CRPP collaborates to the European Program on fusion research in the framework of EURATOM. The advantages of fusion are remarkable: the fuel is available in great quantity all over the world; the reactor is intrinsically safe; the reactor material, activated during operation, loses practically all its activity within about 100 years. But the working up of the controlled fusion necessitates extreme technological conditions. In 1979, the Joint European Torus (JET) began its operation; today it is still the most powerful tokamak in the world; its energy yield Q reached 0.65. The progress realized in the framework of EURATOM has led to the planning of the experimental reactor ITER which is being built at Cadarache (France). ITER is designed to reach a Q-value largely above 1. The future prototype reactor DEMO is foreseen in 2040-2050. It should demonstrate the ability of a fusion reactor to inject electricity into the grid for long term. In 2014, CRPP participated in the works on ITER in the framework of the Fusion for Energy (F4E) agency. At EPFL the research concerns the physics of the magnetic confinement with experiments on the tokamak TCV (variable configuration tokamak), the numerical simulations, the plasma heating and the generation of current by hyper frequency radio waves. At the Paul Scherrer Institute (PSI), research is devoted to the superconductivity. At the Basel University the studies get on interactions between the plasma and the tokamak walls. The large flexibility of TCV allows creating and controlling plasmas of different shapes which are necessary to optimise the core geometry of future reactors. Moreover, the plasma heating by mm radio waves allows guiding the injected power according to specific

Plasma physics and controlled nuclear fusion research

International Nuclear Information System (INIS)

1980-01-01

Full text: During the last decade, growing efforts have been devoted to studying the possible forms an electricity-producing thermonuclear reactor might take and the various technical problems that will have to be overcome. Previous IAEA Conferences took place in Salzburg (1961), Culham (1965), Novosibirsk (1968), Madison (1971), Tokyo (1974), Berchtesgaden (1976) and Innsbruck (1978) The exchange of information that has characterized this series of meetings is an important example of international co-operation and has contributed substantially to progress in controlled fusion research. The results of experiments in major research establishments, as well as the growing scientific insights in the field of plasma physics, give hope that the realization of nuclear fusion will be made possible on a larger scale and beyond the laboratory stage by the end of this century. The increase of the duration of existing tokamak discharges requires solution of the impurity control problem. First results from the new big machines equipped with the poloidal divertor recently came into operation. PDX (USA) and ASDEX (F.R. of Germany) show that various divertor configurations can be established and maintained and that the divertors function in the predicted manner. The reduction of high-Z impurities on these machines by a factor 10 was achieved. As a result of extensive research on radio-frequency (RF) plasma heating on tokamaks: PLT (USA), TFR (France), JFT-2 (Japan), the efficiency of this attractive method of plasma heating comparable to neutral beam heating was demonstrated. It was shown that the density of the input power of about 5-10 kW/cm 2 is achievable and this limit is high enough for application to reactor-like machines. One of the inspiring results reported at the conference was the achievement of value (the ratio of plasma pressure to magnetic field pressure) of ∼ 3% on tokamaks T-11 (USSR) and ISX-B (USA). It is important to note that this value exceeds the

Achievement of solid-state plasma fusion ('Cold-Fusion')

International Nuclear Information System (INIS)

Arata, Yoshiaki; Zhang, Yue-Chang

1995-01-01

Using a 'QMS' (Quadrupole Mass Spectrometer), the authors detected a significantly large amount (10 20 -10 21 [cm -3 ]) of helium ( 2 4 He), which was concluded to have been produced by a deuterium nuclear reaction within a host solid. These results were found to be fully repeatable and supported the authors' proposition that solid state plasma fusion ('Cold Fusion') can be generated in energetic deuterium Strongly Coupled Plasma ('SC-plasma'). This fusion reaction is thought to be sustained by localized 'Latticequake' in a solid-state media with the deuterium density equivalent to that of the host solid. While exploring this basic proposition, the characteristic differences when compared with ultra high temperature-state plasma fusion ('Hot Fusion') are clarified. In general, the most essential reaction product in both types of the deuterium plasma fusion is considered to be helium, irrespective of the 'well-known and/or unknown reactions', which is stored within the solid-state medium in abundance as a 'Residual Product', but which generally can not enter into nor be released from host-solid at a room temperature. Even measuring instruments with relatively poor sensitivity should be able to easily detect such residual helium. An absence of residual helium means that no nuclear fusion reaction has occurred, whereas its presence provides crucial evidence that nuclear fusion has, in fact, occurred in the solid. (author)

Fusion Implementation

International Nuclear Information System (INIS)

Schmidt, J.A.

2002-01-01

If a fusion DEMO reactor can be brought into operation during the first half of this century, fusion power production can have a significant impact on carbon dioxide production during the latter half of the century. An assessment of fusion implementation scenarios shows that the resource demands and waste production associated with these scenarios are manageable factors. If fusion is implemented during the latter half of this century it will be one element of a portfolio of (hopefully) carbon dioxide limiting sources of electrical power. It is time to assess the regional implications of fusion power implementation. An important attribute of fusion power is the wide range of possible regions of the country, or countries in the world, where power plants can be located. Unlike most renewable energy options, fusion energy will function within a local distribution system and not require costly, and difficult, long distance transmission systems. For example, the East Coast of the United States is a prime candidate for fusion power deployment by virtue of its distance from renewable energy sources. As fossil fuels become less and less available as an energy option, the transmission of energy across bodies of water will become very expensive. On a global scale, fusion power will be particularly attractive for regions separated from sources of renewable energy by oceans

Annual report of the Summit Members' Working Group on Controlled Thermonuclear Fusion (Fusin Working Group (FWG))

Energy Technology Data Exchange (ETDEWEB)

none,

1987-04-01

The Summit Members' Working Group on Controlled Thermonuclear Fusion (Fusion Working Group (FWG)) was established in 1983 in response to the Declaration of the Heads of State and Government at the Versailles Economic Summit meeting of 1982, and in response to the subsequent report of the Working Group in Technology, Growth and Employment (TGE) as endorsed at the Williamsburg Summit meeting, 1983. This document contains the complete written record of each of the three FWG meetings which include the minutes, lists of attendees, agendas, statements, and summary conclusions as well as the full reports of the Technical Working Party. In addition, there is a pertinent exchange of correspondence between FWG members on the role of the Technical Working Party and a requested background paper on the modalities associated with a possible future ETR project.

Fusion: introduction

International Nuclear Information System (INIS)

Decreton, M.

2006-01-01

The article gives an overview and introduction to the activities of SCK-CEN's research programme on fusion. The decision to construct the ITER international nuclear fusion experiment in Cadarache is highlighted. A summary of the Belgian contributions to fusion research is given with particular emphasis on studies of radiation effects on diagnostics systems, radiation effects on remote handling sensing systems, fusion waste management and socio-economic studies

Rasiowa completion versus Keisler saturation: Towards a pragmatics of infinite fusion

Energy Technology Data Exchange (ETDEWEB)

Tomasik, J.A. [Univ. of Clermont (France)

1996-12-31

The goal of this survey note is to make a step towards a semiotical approach to the control of Sensor Data Fusion systems. We try to adapt infinitistic methods of Rasiowa and Keisler as prototypes of a many-one pragmatics for the control of SDF in order to provide a faithful system - semantical or/and syntactical - adequate for simultaneous interpretation of signals received through several sensors. Intuitively, it is clear that the amount of the information captured during the fusion process depends strongly on the fusion itself. Nevertheless we can find (c.f. works of Kokar`s group) the following implicit heuristic in semiotical investigations on Sensory Data Fusion Z`s accepted.

An experiment to test centrifugal confinement for fusion

International Nuclear Information System (INIS)

Ellis, R.F.; Hassam, A.B.; Messer, S.; Osborn, B.R.

2001-01-01

The basic idea of centrifugal confinement is to use centrifugal forces from supersonic rotation to augment conventional magnetic confinement. Optimizing this 'knob' results in a fusion device that features four advantages: steady state, no disruptions, superior cross-field confinement, and a simpler coil configuration. The idea rests on two prongs: first, centrifugal forces can confine plasmas to desired regions of shaped magnetic fields; second, the accompanying large velocity shear can stabilize even magnetohydrodynamic (MHD) instabilities. A third feature is that the velocity shear also viscously heats the plasma; no auxiliary heating is necessary to reach fusion temperatures. Regarding transport, the velocity shear can also quell microturbulence, leading to fully classical confinement, as there are no neoclassical effects. Classical parallel electron transport then sets the confinement time. These losses are minimized by a large Pastukhov factor resulting from the deep centrifugal potential well: at Mach 4-5, the Lawson criterion is accessible. One key issue is whether velocity shear will be sufficient by itself to stabilize MHD interchanges. Numerical simulations indicate that laminar equilibria can be obtained at Mach numbers of 4-5 but that the progression toward laminarity with increasing Mach number is accompanied by residual convection from the interchanges. The central goal of the Maryland Centrifugal Torus (MCT) [R. F. Ellis et al., Bull. Am. Phys. Soc. 44, 48 (1998)] is to obtain MHD stability from velocity shear. As an assist to accessing laminarity, MCT will incorporate two unique features: plasma elongation and toroidal magnetic field. The former raises velocity shear efficiency, and modest magnetic shear should suppress residual convection

High-Frequency Gravitational Wave Induced Nuclear Fusion

International Nuclear Information System (INIS)

Fontana, Giorgio; Baker, Robert M. L. Jr.

2007-01-01

Nuclear fusion is a process in which nuclei, having a total initial mass, combine to produce a single nucleus, having a final mass less than the total initial mass. Below a given atomic number the process is exothermic; that is, since the final mass is less than the combined initial mass and the mass deficit is converted into energy by the nuclear fusion. On Earth nuclear fusion does not happen spontaneously because electrostatic barriers prevent the phenomenon. To induce controlled, industrial scale, nuclear fusion, only a few methods have been discovered that look promising, but net positive energy production is not yet possible because of low overall efficiency of the systems. In this paper we propose that an intense burst of High Frequency Gravitational Waves (HFGWs) could be focused or beamed to a target mass composed of appropriate fuel or target material to efficiently rearrange the atomic or nuclear structure of the target material with consequent nuclear fusion. Provided that efficient generation of HFGW can be technically achieved, the proposed fusion reactor could become a viable solution for the energy needs of mankind and alternatively a process for beaming energy to produce a source of fusion energy remotely - even inside solid materials

2001 activity report of the development and research line in controlled thermonuclear fusion of the Plasma Associated Laboratory

International Nuclear Information System (INIS)

Ludwig, Gerson Otto

2002-01-01

The year 2001 activities of the controlled thermonuclear fusion research line of the Plasma Associated Laboratory at the National Institute for Space Research - Brazil are reported. The report approaches the staff, participation in congresses, goals for the year 2002 and papers on Tokamak plasmas, plasma diagnostic, bootstraps, plasma equilibrium and diagnostic

Spatial distribution of turbulence in the Wendelstein 7-AS stellarator (invited paper)

DEFF Research Database (Denmark)

Basse, N.P.; Michelsen, Poul; Zoletnik, S.

2002-01-01

In this paper measurements of short wavelength electron density fluctuations using collective scattering of infrared light are presented. The Wendelstein 7-AS (W7-AS) stellarator (Renner H et al 1989 Plasma Phys. Control. Fusion 31 1579) and the diagnostic are briefly described. A series of plasm...

Anato-metabolic fusion of PET, CT and MRI images

International Nuclear Information System (INIS)

Przetak, C.; Baum, R.P.; Niesen, A.; Slomka, P.; Proeschild, A.; Leonhardi, J.

2000-01-01

The fusion of cross-sectional images - especially in oncology - appears to be a very helpful tool to improve the diagnostic and therapeutic accuracy. Though many advantages exist, image fusion is applied routinely only in a few hospitals. To introduce image fusion as a common procedure, technical and logistical conditions have to be fulfilled which are related to long term archiving of digital data, data transfer and improvement of the available software in terms of usefulness and documentation. The accuracy of coregistration and the quality of image fusion has to be validated by further controlled studies. (orig.) [de

Recent fusion research in the National Institute for Fusion Science

International Nuclear Information System (INIS)

Komori, Akio; Sakakibara, Satoru; Sagara, Akio; Horiuchi, Ritoku; Yamada, Hiroshi; Takeiri, Yasuhiko

2011-01-01

The National Institute for Fusion Science (NIFS), which was established in 1989, promotes academic approaches toward the exploration of fusion science for steady-state helical reactor and realizes the establishment of a comprehensive understanding of toroidal plasmas as an inter-university research organization and a key center of worldwide fusion research. The Large Helical Device (LHD) Project, the Numerical Simulation Science Project, and the Fusion Engineering Project are organized for early realization of net current free fusion reactor, and their recent activities are described in this paper. The LHD has been producing high-performance plasmas comparable to those of large tokamaks, and several new findings with regard to plasma physics have been obtained. The numerical simulation science project contributes understanding and systemization of the physical mechanisms of plasma confinement in fusion plasmas and explores complexity science of a plasma for realization of the numerical test reactor. In the fusion engineering project, the design of the helical fusion reactor has progressed based on the development of superconducting coils, the blanket, fusion materials and tritium handling. (author)

Theoretical quantification of shock-timing sensitivities for direct-drive inertial confinement fusion implosions on OMEGA

Science.gov (United States)

Cao, D.; Boehly, T. R.; Gregor, M. C.; Polsin, D. N.; Davis, A. K.; Radha, P. B.; Regan, S. P.; Goncharov, V. N.

2018-05-01

Using temporally shaped laser pulses, multiple shocks can be launched in direct-drive inertial confinement fusion implosion experiments to set the shell on a desired isentrope or adiabat. The velocity of the first shock and the times at which subsequent shocks catch up to it are measured through the velocity interferometry system for any reflector diagnostic [T. R. Boehly et al., Phys. Plasmas 18, 092706 (2011)] on OMEGA [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. Simulations reproduce these velocity and shock-merger time measurements when using laser pulses designed for setting mid-adiabat (α ˜ 3) implosions, but agreement degrades for lower-adiabat (α ˜ 1) designs. Simulation results indicate that the shock timing discrepancy is most sensitive to details of the density and temperature profiles in the coronal plasma, which influences the laser energy coupled into the target, and only marginally sensitive to the target offset and beam power imbalance. To aid in verifying the coronal profile's influence, a new technique under development to infer coronal profiles using x-ray self-emission imaging [A. K. Davis et al., Bull. Am. Phys. Soc. 61, BAPS.2016.DPP.NO8.7 (2016)] can be applied to the pulse shapes used in shock-timing experiments.

Viral membrane fusion

International Nuclear Information System (INIS)

Harrison, Stephen C.

2015-01-01

Membrane fusion is an essential step when enveloped viruses enter cells. Lipid bilayer fusion requires catalysis to overcome a high kinetic barrier; viral fusion proteins are the agents that fulfill this catalytic function. Despite a variety of molecular architectures, these proteins facilitate fusion by essentially the same generic mechanism. Stimulated by a signal associated with arrival at the cell to be infected (e.g., receptor or co-receptor binding, proton binding in an endosome), they undergo a series of conformational changes. A hydrophobic segment (a “fusion loop” or “fusion peptide”) engages the target-cell membrane and collapse of the bridging intermediate thus formed draws the two membranes (virus and cell) together. We know of three structural classes for viral fusion proteins. Structures for both pre- and postfusion conformations of illustrate the beginning and end points of a process that can be probed by single-virion measurements of fusion kinetics. - Highlights: • Viral fusion proteins overcome the high energy barrier to lipid bilayer merger. • Different molecular structures but the same catalytic mechanism. • Review describes properties of three known fusion-protein structural classes. • Single-virion fusion experiments elucidate mechanism

Viral membrane fusion

Energy Technology Data Exchange (ETDEWEB)

Harrison, Stephen C., E-mail: harrison@crystal.harvard.edu

2015-05-15

Membrane fusion is an essential step when enveloped viruses enter cells. Lipid bilayer fusion requires catalysis to overcome a high kinetic barrier; viral fusion proteins are the agents that fulfill this catalytic function. Despite a variety of molecular architectures, these proteins facilitate fusion by essentially the same generic mechanism. Stimulated by a signal associated with arrival at the cell to be infected (e.g., receptor or co-receptor binding, proton binding in an endosome), they undergo a series of conformational changes. A hydrophobic segment (a “fusion loop” or “fusion peptide”) engages the target-cell membrane and collapse of the bridging intermediate thus formed draws the two membranes (virus and cell) together. We know of three structural classes for viral fusion proteins. Structures for both pre- and postfusion conformations of illustrate the beginning and end points of a process that can be probed by single-virion measurements of fusion kinetics. - Highlights: • Viral fusion proteins overcome the high energy barrier to lipid bilayer merger. • Different molecular structures but the same catalytic mechanism. • Review describes properties of three known fusion-protein structural classes. • Single-virion fusion experiments elucidate mechanism.

Hybrid Fusion for Biometrics: Combining Score-level and Decision-level Fusion

NARCIS (Netherlands)

Tao, Q.; Veldhuis, Raymond N.J.

2008-01-01

A general framework of fusion at decision level, which works on ROCs instead of matching scores, is investigated. Under this framework, we further propose a hybrid fusion method, which combines the score-level and decision-level fusions, taking advantage of both fusion modes. The hybrid fusion

Intense fusion neutron sources

International Nuclear Information System (INIS)

Kuteev, B. V.; Goncharov, P. R.; Sergeev, V. Yu.; Khripunov, V. I.

2010-01-01

The review describes physical principles underlying efficient production of free neutrons, up-to-date possibilities and prospects of creating fission and fusion neutron sources with intensities of 10 15 -10 21 neutrons/s, and schemes of production and application of neutrons in fusion-fission hybrid systems. The physical processes and parameters of high-temperature plasmas are considered at which optimal conditions for producing the largest number of fusion neutrons in systems with magnetic and inertial plasma confinement are achieved. The proposed plasma methods for neutron production are compared with other methods based on fusion reactions in nonplasma media, fission reactions, spallation, and muon catalysis. At present, intense neutron fluxes are mainly used in nanotechnology, biotechnology, material science, and military and fundamental research. In the near future (10-20 years), it will be possible to apply high-power neutron sources in fusion-fission hybrid systems for producing hydrogen, electric power, and technological heat, as well as for manufacturing synthetic nuclear fuel and closing the nuclear fuel cycle. Neutron sources with intensities approaching 10 20 neutrons/s may radically change the structure of power industry and considerably influence the fundamental and applied science and innovation technologies. Along with utilizing the energy produced in fusion reactions, the achievement of such high neutron intensities may stimulate wide application of subcritical fast nuclear reactors controlled by neutron sources. Superpower neutron sources will allow one to solve many problems of neutron diagnostics, monitor nano-and biological objects, and carry out radiation testing and modification of volumetric properties of materials at the industrial level. Such sources will considerably (up to 100 times) improve the accuracy of neutron physics experiments and will provide a better understanding of the structure of matter, including that of the neutron itself.

Intense fusion neutron sources

Science.gov (United States)

Kuteev, B. V.; Goncharov, P. R.; Sergeev, V. Yu.; Khripunov, V. I.

2010-04-01

The review describes physical principles underlying efficient production of free neutrons, up-to-date possibilities and prospects of creating fission and fusion neutron sources with intensities of 1015-1021 neutrons/s, and schemes of production and application of neutrons in fusion-fission hybrid systems. The physical processes and parameters of high-temperature plasmas are considered at which optimal conditions for producing the largest number of fusion neutrons in systems with magnetic and inertial plasma confinement are achieved. The proposed plasma methods for neutron production are compared with other methods based on fusion reactions in nonplasma media, fission reactions, spallation, and muon catalysis. At present, intense neutron fluxes are mainly used in nanotechnology, biotechnology, material science, and military and fundamental research. In the near future (10-20 years), it will be possible to apply high-power neutron sources in fusion-fission hybrid systems for producing hydrogen, electric power, and technological heat, as well as for manufacturing synthetic nuclear fuel and closing the nuclear fuel cycle. Neutron sources with intensities approaching 1020 neutrons/s may radically change the structure of power industry and considerably influence the fundamental and applied science and innovation technologies. Along with utilizing the energy produced in fusion reactions, the achievement of such high neutron intensities may stimulate wide application of subcritical fast nuclear reactors controlled by neutron sources. Superpower neutron sources will allow one to solve many problems of neutron diagnostics, monitor nano-and biological objects, and carry out radiation testing and modification of volumetric properties of materials at the industrial level. Such sources will considerably (up to 100 times) improve the accuracy of neutron physics experiments and will provide a better understanding of the structure of matter, including that of the neutron itself.

Work on fusion technology at Studsvik during 1978

International Nuclear Information System (INIS)

Pauli, R.; Espefaelt, R.; Lorenzen, J.

1978-02-01

Studsvik is associated with the EUR-ATOM fusion research program and work within fusion technology is carried out regarding reactor control, conceptual design, safety and environmental impact; radiation damage. In addition research by subcontracts is done in atomic physics data at Lund university and in surface physics at Research Institute of Physics, Stockholm university. (author)

Heavy ion fusion

International Nuclear Information System (INIS)

Hofmann, Ingo

1993-01-01

With controlled thermonuclear fusion holding out the possibility of a prolific and clean new source of energy, the goal remains elusive after many years of continual effort. While the conventional Tokamak route with magnetic confinement continues to hit the headlines, other alternatives are now becoming competitive. One possible solution is to confine the thermonuclear fuel pellet by high power beams. Current research and perspectives for future work in such inertial confinement was the subject of the 'Prospects for Heavy Ion Fusion' European Research Conference held in Aghia Pelaghia, Crete, last year. Its main focus was on the potential of heavy ion accelerators as well as recent advances in target physics with high power lasers and light ion beams. Carlo Rubbia declared that high energy accelerators, with their high efficiency, are the most promising approach to economical fusion energy production. However the need for cost saving in the driver accelerator requires new ideas in target design tailored to the particularities of heavy ion beams, which need to be pushed to the limits of high current and phase space density at the same time

Optical Lattice Bose-Einstein Condensates and the dd Fusion - Iwamura Connection

Science.gov (United States)

Chubb, Talbot

2003-03-01

My conjecture: LENR dd fusion occurs in PdDx when a subset of the interstitial deuterons occupy tetrahedral sites in a PdDx crystallite. The tetrahedral deuterons(d's), which occupy shallow potential wells, behave as a superfluid, similar to ultracold Na atoms in shallow-well optical traps, as modeled by Jaksch et al.(D. Jaksch, et al, Phys. Rev. Lett., 81, 3108 (1998).) The tetrahedral d's form a deuteron (d) subsystem, which is neutralized by an electron subsystem containing an equal number of electrons. In the superfluid all the properties of each quasiparticle d are partitioned among N_s_i_te equivalent sites. The partitioning of the d point charge reduces the Coulomb self-repulsion within each quasiparticle pair, which causes wave function overlap at large N_s_i_t_e, allowing d-d fusion. Similarly, partitioning of the point charge of each single quasiparticle d reduces the Coulomb repulsion between it and an obstructing impurity atom, which causes wave function overlap between quasiparticle and atom at large N_s_i_t_e, allowing transmutation of the impurity atom. The Iwamura reaction(Y. Iwamura, et al, Japan J. of Appl. Physics, 41A, 4642 (2002).) is 4 ^2D^+_B_l_o_ch + 4 e^-_B_l_o_ch + ^1^3^3Cs arrow ^1^4^1Pr, with the reaction energy incoherently transferred to the lattice.

Peaceful fusion

Energy Technology Data Exchange (ETDEWEB)

Englert, Matthias [IANUS, TU Darmstadt (Germany)

2014-07-01

Like other intense neutron sources fusion reactors have in principle a potential to be used for military purposes. Although the use of fissile material is usually not considered when thinking of fusion reactors (except in fusion-fission hybrid concepts) quantitative estimates about the possible production potential of future commercial fusion reactor concepts show that significant amounts of weapon grade fissile materials could be produced even with very limited amounts of source materials. In this talk detailed burnup calculations with VESTA and MCMATH using an MCNP model of the PPCS-A will be presented. We compare different irradiation positions and the isotopic vectors of the plutonium bred in different blankets of the reactor wall with the liquid lead-lithium alloy replaced by uranium. The technical, regulatory and policy challenges to manage the proliferation risks of fusion power will be addressed as well. Some of these challenges would benefit if addressed at an early stage of the research and development process. Hence, research on fusion reactor safeguards should start as early as possible and accompany the current research on experimental fusion reactors.

The tritium and the controlled fusion reactors

International Nuclear Information System (INIS)

Leger, D.; Rouyer, J.L.

1986-04-01

It is shown how tritium is used how it is circulating in a fusion reactor. The great functions of tritium circuits are detailed: reprocessing of burnt gases, reprocessing of gases coming from neutral injectors, reprocessing from gaseous wastes, detritiation of cooling fluids. Current technologic developments are quoted. Then tritium confinement and containment, in normal or accidental situations, are displayed. Limitation devices of effluents and release for normal operating (noticeably the reprocessing systems of atmosphere) and safety and protection systems in case of accident are described [fr

ASDEX contributions to the 17th European conference on controlled fusion and plasma heating

International Nuclear Information System (INIS)

1990-09-01

The 'ASDEX contributions to the 17th European conference on controlled fusion and plasma heating' (Amsterdam, June 25-29, 1990) hold one invited paper (Physics of enhanced confinement with peaked and board density profiles) and 12 chapters containing 44 contributed papers dealing with the following topics: Lower hybrid current drive and heating; Ion cyclotron heating; General confinement studies; Fluctuation studies; Direct measurement of transport coefficients; H-mode studies; Pellet studies; Divertor and SOL-studies; Impurity and impurity transport studies; Density limit studies; MHD studies; Diagnostic development. (orig./AH)

Cold fusion, Alchemist's dream

International Nuclear Information System (INIS)

Clayton, E.D.

1989-09-01

In this report the following topics relating to cold fusion are discussed: muon catalysed cold fusion; piezonuclear fusion; sundry explanations pertaining to cold fusion; cosmic ray muon catalysed cold fusion; vibrational mechanisms in excited states of D 2 molecules; barrier penetration probabilities within the hydrogenated metal lattice/piezonuclear fusion; branching ratios of D 2 fusion at low energies; fusion of deuterons into 4 He; secondary D+T fusion within the hydrogenated metal lattice; 3 He to 4 He ratio within the metal lattice; shock induced fusion; and anomalously high isotopic ratios of 3 He/ 4 He

Progress of nuclear fusion research and review on development of fusion reactors

International Nuclear Information System (INIS)

1976-01-01

Set up in October 1971, the ad hoc Committee on Survey of Nuclear Fusion Reactors has worked on overall fusion reactor aspects and definition of the future problems under four working groups of core, nuclear heat, materials and system. The presect volume is intended to provide reference materials in the field of fusion reactor engineering, prepared by members of the committee. Contents are broadly the following: concept of the nuclear fusion reactor, fusion core engineering, fusion reactor blanket engineering, fusion reactor materials engineering, and system problems in development of fusion reactors. (Mori, K.)

The effects of local insulin application to lumbar spinal fusions in a rat model.

Science.gov (United States)

Koerner, John D; Yalamanchili, Praveen; Munoz, William; Uko, Linda; Chaudhary, Saad B; Lin, Sheldon S; Vives, Michael J

2013-01-01

The rates of pseudoarthrosis after a single-level spinal fusion have been reported up to 35%, and the agents that increase the rate of fusion have an important role in decreasing pseudoarthrosis after spinal fusion. Previous studies have analyzed the effects of local insulin application to an autograft in a rat segmental defect model. Defects treated with a time-released insulin implant had significantly more new bone formation and greater quality of bone compared with controls based on histology and histomorphometry. A time-released insulin implant may have similar effects when applied in a lumbar spinal fusion model. This study analyzes the effects of a local time-released insulin implant applied to the fusion bed in a rat posterolateral lumbar spinal fusion model. Our hypothesis was twofold: first, a time-released insulin implant applied to the autograft bed in a rat posterolateral lumbar fusion will increase the rate of successful fusion and second, will alter the local environment of the fusion site by increasing the levels of local growth factors. Animal model (Institutional Animal Care and Use Committee approved) using 40 adult male Sprague-Dawley rats. Forty skeletally mature Sprague-Dawley rats weighing approximately 500 g each underwent posterolateral intertransverse lumbar fusions with iliac crest autograft from L4 to L5 using a Wiltse-type approach. After exposure of the transverse processes and high-speed burr decortication, a Linplant (Linshin Canada, Inc., ON, Canada) consisting of 95% microrecrystalized palmitic acid and 5% bovine insulin (experimental group) or a sham implant consisting of only palmitic acid (control group) was implanted on the fusion bed with iliac crest autograft. As per the manufacturer, the Linplant has a release rate of 2 U/day for a minimum of 40 days. The transverse processes and autograft beds of 10 animals from the experimental and 10 from the control group were harvested at Day 4 and analyzed for growth factors. The

An analytical demonstration of coupling schemes between magnetohydrodynamic codes and eddy current codes

International Nuclear Information System (INIS)

Liu Yueqiang; Albanese, R.; Rubinacci, G.; Portone, A.; Villone, F.

2008-01-01

In order to model a magnetohydrodynamic (MHD) instability that strongly couples to external conducting structures (walls and/or coils) in a fusion device, it is often necessary to combine a MHD code solving for the plasma response, with an eddy current code computing the fields and currents of conductors. We present a rigorous proof of the coupling schemes between these two types of codes. One of the coupling schemes has been introduced and implemented in the CARMA code [R. Albanese, Y. Q. Liu, A. Portone, G. Rubinacci, and F. Villone, IEEE Trans. Magn. 44, 1654 (2008); A. Portone, F. Villone, Y. Q. Liu, R. Albanese, and G. Rubinacci, Plasma Phys. Controlled Fusion 50, 085004 (2008)] that couples the MHD code MARS-F[Y. Q. Liu, A. Bondeson, C. M. Fransson, B. Lennartson, and C. Breitholtz, Phys. Plasmas 7, 3681 (2000)] and the eddy current code CARIDDI[R. Albanese and G. Rubinacci, Adv. Imaging Electron Phys. 102, 1 (1998)]. While the coupling schemes are described for a general toroidal geometry, we give the analytical proof for a cylindrical plasma.

Fusion power: the transition from fundamental science to fusion reactor engineering

International Nuclear Information System (INIS)

Post, R.F.

1975-01-01

The historical development of fusion research is outlined. The basics of fusion power along with fuel cost and advantages of fusion are discussed. Some quantitative requirements for fusion power are described. (MOW)

Trends in fusion reactor safety research

International Nuclear Information System (INIS)

Herring, J.S.; Holland, D.F.; Piet, S.J.

1991-01-01

Fusion has the potential to be an attractive energy source. From the safety and environmental perspective, fusion must avoid concerns about catastrophic accidents and unsolvable waste disposal. In addition, fusion must achieve an acceptable level of risk from operational accidents that result in public exposure and economic loss. Finally, fusion reactors must control routine radioactive effluent, particularly tritium. Major progress in achieving this potential rests on development of low-activation materials or alternative fuels. The safety and performance of various material choices and fuels for commercial fusion reactors can be investigated relatively inexpensively through reactor design studies. These studies bring together experts in a wide range of backgrounds and force the group to either agree on a reactor design or identify areas for further study. Fusion reactors will be complex with distributed radioactive inventories. The next generation of experiments will be critical in demonstrating that acceptable levels of safe operation can be achieved. These machines will use materials which are available today and for which a large database exists (e.g. for 316 stainless steel). Researchers have developed a good understanding of the risks associated with operation of these devices. Specifically, consequences from coolant system failures, loss of vacuum events, tritium releases, and liquid metal reactions have been studied. Recent studies go beyond next step designs and investigate commercial reactor concerns including tritium release and liquid metal reactions. 18 refs

Laser-Plasma Interactions on NIKE and the Fusion Test Facility

Science.gov (United States)

Phillips, Lee; Weaver, James

2008-11-01

Recent proposed designs for a Fusion Test Facility (FTF) (Obenchain et al., Phys. Plasmas 13 056320 (2006)) for direct-drive ICF targets for energy applications involve high implosion velocities combined with higher laser irradiances. The use of high irradiances increases the likelihood of deleterious laser plasma instabilities (LPI) but the proposed use of a 248 nm KrF laser to drive these targets is expected to minimize the LPI risk. We examine, using simulation results from NRL's FAST hydrocode, the proposed operational regimes of the FTF in relation to the thresholds for the SRS, SBS, and 2-plasmon instabilities. Simulations are also used to help design and interpret ongoing experiments being conducted at NRL's NIKE facility for the purpose of generating and studying LPI. Target geometries and laser pulseshapes were devised in order to create plasma conditions with long scalelengths and low electron temperatures that allow the growth of parametric instabilities. These simulations include the effects of finite beam angles through the use of raytracing.

Theory of hydro-equivalent ignition for inertial fusion and its applications to OMEGA and the National Ignition Facility

Energy Technology Data Exchange (ETDEWEB)

Nora, R.; Betti, R.; Bose, A.; Woo, K. M.; Christopherson, A. R.; Meyerhofer, D. D. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States); Fusion Science Center, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States); Department of Physics and/or Mechanical Engineering, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States); Anderson, K. S.; Shvydky, A.; Marozas, J. A.; Collins, T. J. B.; Radha, P. B.; Hu, S. X.; Epstein, R.; Marshall, F. J.; Sangster, T. C. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States); McCrory, R. L. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States); Department of Physics and/or Mechanical Engineering, University of Rochester, 250 East River Road, Rochester, New York 14623-1299 (United States)

2014-05-15

The theory of ignition for inertial confinement fusion capsules [R. Betti et al., Phys. Plasmas 17, 058102 (2010)] is used to assess the performance requirements for cryogenic implosion experiments on the Omega Laser Facility. The theory of hydrodynamic similarity is developed in both one and two dimensions and tested using multimode hydrodynamic simulations with the hydrocode DRACO [P. B. Radha et al., Phys. Plasmas 12, 032702 (2005)] of hydro-equivalent implosions (implosions with the same implosion velocity, adiabat, and laser intensity). The theory is used to scale the performance of direct-drive OMEGA implosions to the National Ignition Facility (NIF) energy scales and determine the requirements for demonstrating hydro-equivalent ignition on OMEGA. Hydro-equivalent ignition on OMEGA is represented by a cryogenic implosion that would scale to ignition on the NIF at 1.8 MJ of laser energy symmetrically illuminating the target. It is found that a reasonable combination of neutron yield and areal density for OMEGA hydro-equivalent ignition is 3 to 6 × 10{sup 13} and ∼0.3 g/cm{sup 2}, respectively, depending on the level of laser imprinting. This performance has not yet been achieved on OMEGA.

Theory of hydro-equivalent ignition for inertial fusion and its applications to OMEGA and the National Ignition Facility

International Nuclear Information System (INIS)

Nora, R.; Betti, R.; Bose, A.; Woo, K. M.; Christopherson, A. R.; Meyerhofer, D. D.; Anderson, K. S.; Shvydky, A.; Marozas, J. A.; Collins, T. J. B.; Radha, P. B.; Hu, S. X.; Epstein, R.; Marshall, F. J.; Sangster, T. C.; McCrory, R. L.

2014-01-01

The theory of ignition for inertial confinement fusion capsules [R. Betti et al., Phys. Plasmas 17, 058102 (2010)] is used to assess the performance requirements for cryogenic implosion experiments on the Omega Laser Facility. The theory of hydrodynamic similarity is developed in both one and two dimensions and tested using multimode hydrodynamic simulations with the hydrocode DRACO [P. B. Radha et al., Phys. Plasmas 12, 032702 (2005)] of hydro-equivalent implosions (implosions with the same implosion velocity, adiabat, and laser intensity). The theory is used to scale the performance of direct-drive OMEGA implosions to the National Ignition Facility (NIF) energy scales and determine the requirements for demonstrating hydro-equivalent ignition on OMEGA. Hydro-equivalent ignition on OMEGA is represented by a cryogenic implosion that would scale to ignition on the NIF at 1.8 MJ of laser energy symmetrically illuminating the target. It is found that a reasonable combination of neutron yield and areal density for OMEGA hydro-equivalent ignition is 3 to 6 × 10 13 and ∼0.3 g/cm 2 , respectively, depending on the level of laser imprinting. This performance has not yet been achieved on OMEGA

Fusion Canada

International Nuclear Information System (INIS)

1987-07-01

This first issue of a quarterly newsletter announces the startup of the Tokamak de Varennes, describes Canada's national fusion program, and outlines the Canadian Fusion Fuels Technology Program. A map gives the location of the eleven principal fusion centres in Canada. (L.L.)

Canada's Fusion Program

International Nuclear Information System (INIS)

Jackson, D. P.

1990-01-01

Canada's fusion strategy is based on developing specialized technologies in well-defined areas and supplying these technologies to international fusion projects. Two areas are specially emphasized in Canada: engineered fusion system technologies, and specific magnetic confinement and materials studies. The Canadian Fusion Fuels Technology Project focuses on the first of these areas. It tritium and fusion reactor fuel systems, remote maintenance and related safety studies. In the second area, the Centre Canadian de fusion magnetique operates the Tokamak de Varennes, the main magnetic fusion device in Canada. Both projects are partnerships linking the Government of Canada, represented by Atomic Energy of Canada Limited, and provincial governments, electrical utilities, universities and industry. Canada's program has extensive international links, through which it collaborates with the major world fusion programs, including participation in the International Thermonuclear Experimental Reactor project

Atomic fusion, Gerrard atomic fusion

International Nuclear Information System (INIS)

Gerrard, T.H.

1980-01-01

In the approach to atomic fusion described here the heat produced in a fusion reaction, which is induced in a chamber by the interaction of laser beams and U.H.F. electromagnetic beams with atom streams, is transferred to a heat exchanger for electricity generation by a coolant flowing through a jacket surrounding the chamber. (U.K.)

ATCA/AXIe compatible board for fast control and data acquisition in nuclear fusion experiments

International Nuclear Information System (INIS)

Batista, A.J.N.; Leong, C.; Bexiga, V.; Rodrigues, A.P.; Combo, A.; Carvalho, B.B.; Fortunato, J.; Correia, M.; Teixeira, J.P.; Teixeira, I.C.; Sousa, J.; Gonçalves, B.; Varandas, C.A.F.

2012-01-01

Highlights: ► High performance board for fast control and data acquisition. ► Large IO channel number per board with galvanic isolation. ► Optimized for high reliability and availability. ► Targeted for nuclear fusion experiments with long duration discharges. ► To be used on the ITER Fast Plant System Controller prototype. - Abstract: An in-house development of an Advanced Telecommunications Computing Architecture (ATCA) board for fast control and data acquisition, with Input/Output (IO) processing capability, is presented. The architecture, compatible with the ATCA (PICMG 3.4) and ATCA eXtensions for Instrumentation (AXIe) specifications, comprises a passive Rear Transition Module (RTM) for IO connectivity to ease hot-swap maintenance and simultaneously to increase cabling life cycle. The board complies with ITER Fast Plant System Controller (FPSC) guidelines for rear IO connectivity and redundancy, in order to provide high levels of reliability and availability to the control and data acquisition systems of nuclear fusion devices with long duration plasma discharges. Simultaneously digitized data from all Analog to Digital Converters (ADC) of the board can be filtered/decimated in a Field Programmable Gate Array (FPGA), decreasing data throughput, increasing resolution, and sent through Peripheral Component Interconnect (PCI) Express to multi-core processors in the ATCA shelf hub slots. Concurrently the multi-core processors can update the board Digital to Analog Converters (DAC) in real-time. Full-duplex point-to-point communication links between all FPGAs, of peer boards inside the shelf, allow the implementation of distributed algorithms and Multi-Input Multi-Output (MIMO) systems. Support for several timing and synchronization solutions is also provided. Some key features are onboard ADC or DAC modules with galvanic isolation, Xilinx Virtex 6 FPGA, standard Dual Data Rate (DDR) 3 SODIMM memory, standard CompactFLASH memory card, Intelligent

Inertial confinement fusion and related topics

International Nuclear Information System (INIS)

Starodub, A. N.

2007-01-01

The current state of different approaches (laser fusion, light and heavy ions, electron beam) to the realization of inertial confinement fusion is considered. From comparative analysis a conclusion is made that from the viewpoint of physics, technology, safety, and economics the most realistic way to future energetics is an electric power plant based on a hybrid fission-fusion reactor which consists of an external source of neutrons (based on laser fusion) and a subcritical two-cascade nuclear blanket, which yields the energy under the action of 14 MeV neutrons. The main topics on inertial confinement fusion such as the energy driver, the interaction between plasmas and driver beam, the target design are discussed. New concept of creation of a laser driver for IFE based on generation and amplification of radiation with controllable coherence is reported. The performed studies demonstrate that the laser based on generation and amplification of radiation with controllable coherence (CCR laser) has a number of advantages as compared to conventional schemes of lasers. The carried out experiments have shown a possibility of suppression of small-scale self-focusing, formation of laser radiation pulses with required characteristics, simplification of an optical scheme of the laser, good matching of laser-target system and achievement of homogeneous irradiation and high output laser energy density without using traditional correcting systems (phase plates, adaptive optics, space filters etc.). The results of the latest experiments to reach ultimate energy characteristics of the developed laser system are also reported. Recent results from the experiments aimed at studying of the physical processes in targets under illumination by the laser with controllable coherence of radiation are presented and discussed, especially such important laser-matter interaction phenomena as absorption and scattering of the laser radiation, the laser radiation harmonic generation, X

Maryland controlled fusion research program. Volume I

International Nuclear Information System (INIS)

1985-01-01

This renewal proposal describes the University of Maryland research program on Magnetic Fusion Energy for a three-year period beginning January 1, 1986. This program consists of five tasks: (I) Plasma Theory; (II) Electron Cyclotron Emission Diagnostics for Mirror Machines; (III) Electron Cyclotron Emission Diagnostics on TFTR; (IV) Atomic Physics; and (V) Magnetic Field Measurement by Ion Beams. The four separate tasks of continuing research (Tasks I to IV) and the new experimental task (Task V) are described in detail. The task descriptions contain estimated budgets for CY 86, 87, and 88

Fusion reactor safety

International Nuclear Information System (INIS)

1987-12-01

Nuclear fusion could soon become a viable energy source. Work in plasma physics, fusion technology and fusion safety is progressing rapidly in a number of Member States and international collaboration continues on work aiming at the demonstration of fusion power generation. Safety of fusion reactors and technological and radiological aspects of waste management are important aspects in the development and design of fusion machines. In order to provide an international forum to review and discuss the status and the progress made since 1983 in programmes related to operational safety aspects of fusion reactors, their waste management and decommissioning concepts, the IAEA had organized the Technical Committee on ''Fusion Reactor Safety'' in Culham, 3-7 November 1986. All presentations of this meeting were divided into four sessions: 1. Statements on National-International Fusion Safety Programmes (5 papers); 2. Operation and System Safety (15 papers); 3. Waste Management and Decommissioning (5 papers); 4. Environmental Impacts (6 papers). A separate abstract was prepared for each of these 31 papers. Refs, figs, tabs

Magnetic fusion and project ITER

International Nuclear Information System (INIS)

Park, H.K.

1992-01-01

It has already been demonstrated that our economics and international relationship are impacted by an energy crisis. For the continuing prosperity of the human race, a new and viable energy source must be developed within the next century. It is evident that the cost will be high and will require a long term commitment to achieve this goal due to a high degree of technological and scientific knowledge. Energy from the controlled nuclear fusion is a safe, competitive, and environmentally attractive but has not yet been completely conquered. Magnetic fusion is one of the most difficult technological challenges. In modem magnetic fusion devices, temperatures that are significantly higher than the temperatures of the sun have been achieved routinely and the successful generation of tens of million watts as a result of scientific break-even is expected from the deuterium and tritium experiment within the next few years. For the practical future fusion reactor, we need to develop reactor relevant materials and technologies. The international project called ''International Thermonuclear Experimental Reactor (ITER)'' will fulfill this need and the success of this project will provide the most attractive long-term energy source for mankind

R-spondin1 Controls Muscle Cell Fusion through Dual Regulation of Antagonistic Wnt Signaling Pathways

Directory of Open Access Journals (Sweden)

Floriane Lacour

2017-03-01

Full Text Available Wnt-mediated signals are involved in many important steps in mammalian regeneration. In multiple cell types, the R-spondin (Rspo family of secreted proteins potently activates the canonical Wnt/β-catenin pathway. Here, we identify Rspo1 as a mediator of skeletal muscle tissue repair. First, we show that deletion of Rspo1 results in global alteration of muscle regeneration kinetics following acute injury. We find that muscle progenitor cells lacking Rspo1 show delayed differentiation due to reduced activation of Wnt/β-catenin target genes. Furthermore, muscle cells lacking Rspo1 have a fusion phenotype leading to larger myotubes containing supernumerary nuclei both in vitro and in vivo. The increase in muscle fusion was dependent on downregulation of Wnt/β-catenin and upregulation of non-canonical Wnt7a/Fzd7/Rac1 signaling. We conclude that reciprocal control of antagonistic Wnt signaling pathways by Rspo1 in muscle stem cell progeny is a key step ensuring normal tissue architecture restoration following acute damage.

Fusion plasma physics during half a century

International Nuclear Information System (INIS)

Lehnert, Bo

1999-08-01

A review is given on the potentialities of fusion energy with respect to energy production and related environmental problems, the various approaches to controlled thermonuclear fusion, the main problem areas of research, the historical development, the present state of investigations, and future perspectives. This article also presents a personal memorandum of the author. Thereby special reference will be given to part of the research conducted at the Royal Institute of Technology in Stockholm, merely to identify its place within the general historical development. Considerable progress has been made in fusion research during the last decades. In large tokamak experiments temperatures above the ignition limit of about 10 8 K have been reached under break-even conditions where the fusion power generation is comparable to the energy loss. A power producing fusion reactor could in principle be realized already today, but it would not become technically and economically efficient. The future international research programme has therefore to be conducted along broad lines, with necessary ingredients of basis research and new ideas, and also within lines of magnetic confinement being alternative to that of tokamaks

Fusion systems engineering

International Nuclear Information System (INIS)

Anon.

1978-01-01

Research during this report period has covered the following areas: (1) fusion reactor systems studies, (2) development of blanket processing technology for fusion reactors, (3) safety studies of fusion concepts, (4) MACKLIB-IV, a new library of nuclear response functions, (5) energy storage and power supply requirements for commercial fusion reactors, (6) blanket/shield design evaluation for commercial fusion reactors, and (7) cross section measurements, evaluations, and techniques

Comment on “Maxwell's equations and electromagnetic Lagrangian density in fractional form” [J. Math. Phys. 53, 033505 (2012)

International Nuclear Information System (INIS)

Rabei, Eqab M.; Al-Jamel, A.; Widyan, H.; Baleanu, D.

2014-01-01

In a recent paper, Jaradat et al. [J. Math. Phys. 53, 033505 (2012)] have presented the fractional form of the electromagnetic Lagrangian density within the Riemann-Liouville fractional derivative. They claimed that the Agrawal procedure [O. P. Agrawal, J. Math. Anal. Appl. 272, 368 (2002)] is used to obtain Maxwell's equations in the fractional form, and the Hamilton's equations of motion together with the conserved quantities obtained from fractional Noether's theorem are reported. In this comment, we draw the attention that there are some serious steps of the procedure used in their work are not applicable even though their final results are correct. Their work should have been done based on a formulation as reported by Baleanu and Muslih [Phys. Scr. 72, 119 (2005)

Repetitive laser fusion experiment and operation using a target injection system

International Nuclear Information System (INIS)

Nishimura, Yasuhiko; Komeda, Osamu; Mori, Yoshitaka

2017-01-01

Since 2008, a collaborative research project on laser fusion development based on a high-speed ignition method using repetitive laser has been carried out with several collaborative research institutes. This paper reports the current state of operation of high repetition laser fusion experiments, such as target introduction and control based on a target injection system that allows free falling under 1 Hz, using a high repetition laser driver that has been under research and development, as well as the measurement of targets that freely fall. The HAMA laser driver that enabled high repetition fusion experiments is a titanium sapphire laser using a diode-pumped solid-state laser KURE-I of green light output as a driver pump light source. In order to carry out high repetition laser fusion experiments, the target injection device allows free falling of deuterated polystyrene solid sphere targets of 1 mm in diameter under 1 Hz. The authors integrated the developed laser and injection system, and succeeded first in the world in making the nuclear fusion reaction continuously by hitting the target to be injected with laser, which is essential technology for future laser nuclear fusion reactor. In order to realize repetition laser fusion experiments, stable laser, target synchronization control, and target position measurement technologies are indispensable. (A.O.)

Towards fusion energy as a sustainable energy source: Activities at DTU Physics

DEFF Research Database (Denmark)

Rasmussen, Jesper; Christensen, Alexander Simon; Dam, Magnus

2014-01-01

a fusion plasma) and to confine it within magnetic fields. Learning how such plasmas behave and can be controlled is a crucial step towards realizing fusion as a sustainable energy source.At the Plasma Physics and Fusion Energy (PPFE) section at DTU Physics, we are exploring these issues,focusing on areas...

Supervisory control and diagnostics system for the mirror fusion test facility: overview and status 1980

International Nuclear Information System (INIS)

McGoldrick, P.R.

1981-01-01

The Mirror Fusion Test Facility (MFTF) is a complex facility requiring a highly-computerized Supervisory Control and Diagnostics System (SCDS) to monitor and provide control over ten subsystems; three of which require true process control. SCDS will provide physicists with a method of studying machine and plasma behavior by acquiring and processing up to four megabytes of plasma diagnostic information every five minutes. A high degree of availability and throughput is provided by a distributed computer system (nine 32-bit minicomputers on shared memory). Data, distributed across SCDS, is managed by a high-bandwidth Distributed Database Management System. The MFTF operators' control room consoles use color television monitors with touch sensitive screens; this is a totally new approach. The method of handling deviations to normal machine operation and how the operator should be notified and assisted in the resolution of problems has been studied and a system designed

Gyrokinetic equivalence

International Nuclear Information System (INIS)

Parra, Felix I; Catto, Peter J

2009-01-01

We compare two different derivations of the gyrokinetic equation: the Hamiltonian approach in Dubin D H E et al (1983 Phys. Fluids 26 3524) and the recursive methodology in Parra F I and Catto P J (2008 Plasma Phys. Control. Fusion 50 065014). We prove that both approaches yield the same result at least to second order in a Larmor radius over macroscopic length expansion. There are subtle differences in the definitions of some of the functions that need to be taken into account to prove the equivalence.

Rho GTPase activity modulates paramyxovirus fusion protein-mediated cell-cell fusion

International Nuclear Information System (INIS)

Schowalter, Rachel M.; Wurth, Mark A.; Aguilar, Hector C.; Lee, Benhur; Moncman, Carole L.; McCann, Richard O.; Dutch, Rebecca Ellis

2006-01-01

The paramyxovirus fusion protein (F) promotes fusion of the viral envelope with the plasma membrane of target cells as well as cell-cell fusion. The plasma membrane is closely associated with the actin cytoskeleton, but the role of actin dynamics in paramyxovirus F-mediated membrane fusion is unclear. We examined cell-cell fusion promoted by two different paramyxovirus F proteins in three cell types in the presence of constitutively active Rho family GTPases, major cellular coordinators of actin dynamics. Reporter gene and syncytia assays demonstrated that expression of either Rac1 V12 or Cdc42 V12 could increase cell-cell fusion promoted by the Hendra or SV5 glycoproteins, though the effect was dependent on the cell type expressing the viral glycoproteins. In contrast, RhoA L63 decreased cell-cell fusion promoted by Hendra glycoproteins but had little affect on SV5 F-mediated fusion. Also, data suggested that GTPase activation in the viral glycoprotein-containing cell was primarily responsible for changes in fusion. Additionally, we found that activated Cdc42 promoted nuclear rearrangement in syncytia

Decree 2805 by means of which the National Accounting and Control of Basic Nuclear Materials and Special Fusionable Materials System, is established

International Nuclear Information System (INIS)

1979-01-01

This Decree has for object to establish a National Accounting and Control of Basic Nuclear Materials and Special Fusionable Materials System, under the supervision of the National Council for the Nuclear Industry Development. Its aims are to account nuclear materials, to control nuclear activities, to preserve and control nuclear information, to keep technical relationship with specialized organizations, and to garant nuclear safeguards [es

Radiation control in fusion plasmas by magnetic confinement

International Nuclear Information System (INIS)

Dachicourt, R.

2012-10-01

The present work addresses two important issues for the industrial use of fusion: plasma radiation control, as a part of the more general power handling issue, and high density tokamak operation. These two issues will be most critical in the demonstration reactor, called DEMO, intermediate step between ITER and a future commercial reactor. For DEMO, the need to radiate a large fraction of the power so as to limit the peak power load on the divertor will be a key constraint. High confinement will have to be combined with high radiated power fraction, and the required level of plasma purity. The main achievement of this thesis is to have shown experimental evidence of the existence of a stable plasma regime meeting the most critical requirements of a DEMO scenario: an electron density up to 40% above the Greenwald value, together with a fraction of radiated power close to 80%, with a good energy confinement and limited dilution. The plasma is additionally heated with ion cyclotron waves in a central electron heating scenario, featuring alpha particle heating. The original observations reported in this work bring highly valuable new pieces of information both to the physics of the tokamak edge layer and to the construction of an 'integrated operational scenario' required to successfully operate fusion devices. In the way for getting high density plasmas, the new observations involve the following topics. First, the formation of a poloidal asymmetry in the edge electron density profile, with a maximum density located close to toroidal pumped limiter. This asymmetry occurs inside the separatrix, with a constant plasma pressure on magnetic surfaces. Secondly, a correlative decrease of the electron temperature in the same edge region. Thirdly, the excellent coupling capabilities of the ICRH waves, up to a central line averaged electron density of 1.4 times the Greenwald density. Fourthly, a poloidally asymmetric edge radiation region, providing the dissipation of 80% of

International bulletin on atomic and molecular data for fusion. No. 16

International Nuclear Information System (INIS)

Katsonis, K.

1981-06-01

This bulletin deals with atomic and molecular data for fusion. A bibliography for the most recent data presented in the document is provided. Work in progress is briefly reported. ''Data Request'' in the fusion field are also mentioned. The bulletin contains a list of references covering the years 1980 and 1981 for all the publications on controlled fusion and plasma physics

Overview of the Magnetic Fusion Energy Devlopment and Technology Program

International Nuclear Information System (INIS)

1978-03-01

This publication gives a comprehensive introduction to controlled fusion research. Topics covered in the discussion include the following: (1) fusion system engineering and advanced design, (2) plasma engineering, (3) magnetic systems, (4) materials, (5) environment and safety, and (6) alternate energy applications

Lower activation materials and magnetic fusion reactors

International Nuclear Information System (INIS)

Conn, R.W.; Bloom, E.E.; Davis, J.W.; Gold, R.E.; Little, R.; Schultz, K.R.; Smith, D.L.; Wiffen, F.W.

1984-01-01

Radioactivity in fusion reactors can be effectively controlled by materials selection. The detailed relationship between the use of a material for construction of a magnetic fusion reactor and the material's characteristics important to waste disposal, safety, and system maintainability has been studied. The quantitative levels of radioactivation are presented for many materials and alloys, including the role of impurities, and for various design alternatives. A major outcome has been the development of quantitative definitions to characterize materials based on their radioactivation properties. Another key result is a four-level classification scheme to categorize fusion reactors based on quantitative criteria for waste management, system maintenance, and safety. A recommended minimum goal for fusion reactor development is a reference reactor that (a) meets the requirements for Class C shallow land burial of waste materials, (b) permits limited hands-on maintenance outside the magnet's shield within 2 days of a shutdown, and (c) meets all requirements for engineered safety. The achievement of a fusion reactor with at least the characteristics of the reference reactor is a realistic goal. Therefore, in making design choices or in developing particular materials or alloys for fusion reactor applications, consideration must be given to both the activation characteristics of a material and its engineering practicality for a given application

Fusion reactor problems

International Nuclear Information System (INIS)

Carruthers, R.

It is pointed out that plasma parameters for a fusion reactor have been fairly accurately defined for many years, and the real plasma physics objective must be to find the means of achieving and maintaining these specifiable parameters. There is good understanding of the generic technological problems: breading blankets and shields, radiation damage, heat transfer and methods of magnet design. The required plasma parameters for fusion self-heated reactors are established at ntausub(E) approximately 2.10 14 cm -3 sec, plasma radius 1.5 to 3 m, wall loading 5 to 10 MW cm -2 , temperature 15 keV. Within this model plasma control by quasi-steady burn as a key problem is studied. It is emphasized that the future programme must interact more closely with engineering studies and should concentrate upon research which is relevant to reactor plasmas. (V.P.)

Barriers to fusion

International Nuclear Information System (INIS)

Berriman, A.C.; Butt, R.D.; Dasgupta, M.; Hinde, D.J.; Morton, C.R.; Newton, J.O.

1999-01-01

The fusion barrier is formed by the combination of the repulsive Coulomb and attractive nuclear forces. Recent research at the Australian National University has shown that when heavy nuclei collide, instead of a single fusion barrier, there is a set of fusion barriers. These arise due to intrinsic properties of the interacting nuclei such deformation, rotations and vibrations. Thus the range of barrier energies depends on the properties of both nuclei. The transfer of matter between nuclei, forming a neck, can also affect the fusion process. High precision data have been used to determine fusion barrier distributions for many nuclear reactions, leading to new insights into the fusion process

Fusion systems engineering

International Nuclear Information System (INIS)

Anon.

1977-01-01

Summaries of research are included for each of the following topics: (1) fusion reactor systems studies, (2) development of blanket processing technology for fusion reactors, (3) safety studies of fusion concepts, (4) the MACK/MACKLIB system for nuclear response functions, and (5) energy storage and power supply systems for fusion reactors

Turbulence at the transition to the high density H-mode in Wendelstein 7-AS plasmas

DEFF Research Database (Denmark)

Basse, N.P.; Zoletnik, S.; Baumel, S.

2003-01-01

Recently a new improved confinement regime was found in the Wendelstein 7-AS (W7-AS) stellarator (Renner H. et al 1989 Plasma Phys. Control. Fusion 31 1579). The discovery of this high density high confinement mode (HDH-mode) was facilitated by the installation of divertor modules. In this paper,...

Effect of the relative shift between the electron density and temperature pedestal position on the pedestal stability in JET-ILW and comparison with JET-C

Science.gov (United States)

Stefanikova, E.; Frassinetti, L.; Saarelma, S.; Loarte, A.; Nunes, I.; Garzotti, L.; Lomas, P.; Rimini, F.; Drewelow, P.; Kruezi, U.; Lomanowski, B.; de la Luna, E.; Meneses, L.; Peterka, M.; Viola, B.; Giroud, C.; Maggi, C.; contributors, JET

2018-05-01

The electron temperature and density pedestals tend to vary in their relative radial positions, as observed in DIII-D (Beurskens et al 2011 Phys. Plasmas 18 056120) and ASDEX Upgrade (Dunne et al 2017 Plasma Phys. Control. Fusion 59 14017). This so-called relative shift has an impact on the pedestal magnetohydrodynamic (MHD) stability and hence on the pedestal height (Osborne et al 2015 Nucl. Fusion 55 063018). The present work studies the effect of the relative shift on pedestal stability of JET ITER-like wall (JET-ILW) baseline low triangularity (δ) unseeded plasmas, and similar JET-C discharges. As shown in this paper, the increase of the pedestal relative shift is correlated with the reduction of the normalized pressure gradient, therefore playing a strong role in pedestal stability. Furthermore, JET-ILW tends to have a larger relative shift compared to JET carbon wall (JET-C), suggesting a possible role of the plasma facing materials in affecting the density profile location. Experimental results are then compared with stability analysis performed in terms of the peeling-ballooning model and with pedestal predictive model EUROPED (Saarelma et al 2017 Plasma Phys. Control. Fusion). Stability analysis is consistent with the experimental findings, showing an improvement of the pedestal stability, when the relative shift is reduced. This has been ascribed mainly to the increase of the edge bootstrap current, and to minor effects related to the increase of the pedestal pressure gradient and narrowing of the pedestal pressure width. Pedestal predictive model EUROPED shows a qualitative agreement with experiment, especially for low values of the relative shift.

Prospects of the practical use of controlled fusion with plasma magnetic confinement

International Nuclear Information System (INIS)

Golovin, I.N.

1990-01-01

Analysis of energy power development reveals, that fossil fuel - gas, oil, coal - will be depleted in the coming century. To-day there are still no ways of economically efficient full-scale usage of solar energy. Energy power based on division of heavy nuclei causes concern linked with unavoidable accumulation of long-lived radioactive wastes. Thermonuclear power is essentially safe, but application of deuterium fusion with tritium faces invincible difficulties linked with radiation damages of materials. Deuterium fusion with helium-3 solves this problem and opens favourable horizon for development of energy power, which is by 10 5 -10 6 time safer, than modern nuclear reactors. Author does not see any other way to provide mankind with fuel for coming centuries than, to mine helium-3 in the Moon which is technically workable and attracts attenuation to urgency of comprehensive - theoretical, experimental, design -development of efforts linked with D 3 He thermonuclear fusion

Fusion energy 2000. Fusion energy 1998 (2001 Edition). Proceedings

International Nuclear Information System (INIS)

2001-01-01

This CD-ROM contains the Proceedings of 18th International Conference on Fusion Energy. It also contains an updated version of the Fusion Energy Conference 1998 Proceedings (38 additional papers included) as well as information on how to use this CD-ROM. The 18th International Atomic Energy Agency Fusion Energy Conference (FEC-2000) was held in Sorrento, Italy, 4-10 October 2000. 573 participants from over thirty countries and three international organizations took part in this Conference. The Conference was organized by the IAEA in co-operation with the Italian National Agency for New Technology, Energy and Environment (ENEA). Around 400 papers were presented in 22 oral and 8 poster sessions on magnetic confinement experiments, inertial fusion energy, plasma heating and current drive, ITER engineering design activities, magnetic confinement theory, innovative concepts, fusion technology, and safety and environment aspects. The 17th International Atomic Energy Agency (IAEA) Fusion Energy Conference was held in Yokohama, Japan, 19-24 October 1999. This 6-day conference, which was attended by 835 participants from over 30 countries and two international organizations, was organized by the IAEA in co-operation with the Japan Atomic Energy Research Institute (JAERI). More than 360 papers plus 5 summary talks were presented in 23 oral and 8 poster sessions on magnetic confinement and experiments, inertial fusion energy, plasma heating and current drive, ITER engineering design activities, magnetic confinement theory, innovative concepts and fusion technology

Fusion technology 1992

International Nuclear Information System (INIS)

Ferro, C.; Gasparatto, M.; Knoepfel, H.

1993-01-01

The aim of the biennial series of symposia on the title subject, organized by the European Fusion Laboratories, is the exchange of information on the design, construction and operation of fusion experiments and on the technology being developed for the next step devices and fusion reactors. The coverage of the volume includes the technological aspects of fusion reactors in relation to new developments, this forming a guideline for the definition of future work. These proceedings comprise three volumes and contain both the invited lectures and contributed papers presented at the symposium which was attended by 569 participants from around the globe. The 343 papers, including 12 invited papers, characterize the increasing interest of industry in the fusion programme, giving a broad and current overview on the progress and trends fusion technology is experiencing now, as well as indicating the future for fusion devices

Quality dependent fusion of intramodal and multimodal biometric experts

Science.gov (United States)

Kittler, J.; Poh, N.; Fatukasi, O.; Messer, K.; Kryszczuk, K.; Richiardi, J.; Drygajlo, A.

2007-04-01

We address the problem of score level fusion of intramodal and multimodal experts in the context of biometric identity verification. We investigate the merits of confidence based weighting of component experts. In contrast to the conventional approach where confidence values are derived from scores, we use instead raw measures of biometric data quality to control the influence of each expert on the final fused score. We show that quality based fusion gives better performance than quality free fusion. The use of quality weighted scores as features in the definition of the fusion functions leads to further improvements. We demonstrate that the achievable performance gain is also affected by the choice of fusion architecture. The evaluation of the proposed methodology involves 6 face and one speech verification experts. It is carried out on the XM2VTS data base.

STAR Power, an Interactive Educational Fusion CD with a Dynamic, Shaped Tokamak Power Plant Simulator

Science.gov (United States)

Leuer, J. A.; Lee, R. L.; Kellman, A. G.; Chapman Nutt, G. C., Jr.; Holley, G.; Larsen, T. A.

2000-10-01

We describe an interactive, educational fusion adventure game developed within our fusion education program. The theme of the adventure is start-up of a state-of-the-art fusion power plant. To gain access to the power plant control room, the student must complete several education modules, including topics on building an atom, fusion reactions, charged particle motion in electric and magnetic fields, and building a power plant. Review questions, a fusion video, library material and glossary provide additional resources. In the control room the student must start-up a complex, dynamic fusion power plant. The simulation model contains primary elements of a tokamak based device, including a magnetic shaper capable of producing limited and diverted elongated plasmas. A zero dimensional plasma model based on ITER scaling and containing rate based conservation equations provides dynamic feedback through major control parameters such as toroidal field, fueling rate and heating. The game is available for use on PC and Mac. computers. Copies will be available at the conference.

Inertial fusion energy; L'energie de fusion inertielle

Energy Technology Data Exchange (ETDEWEB)

Decroisette, M.; Andre, M.; Bayer, C.; Juraszek, D. [CEA Bruyeres-le-Chatel, Dir. des Systemes d' Information (CEA/DIF), 91 (France); Le Garrec, B. [CEA Centre d' Etudes Scientifiques et Techniques d' Aquitaine, 33 - Le Barp (France); Deutsch, C. [Paris-11 Univ., 91 - Orsay (France); Migus, A. [Institut d' Optique Centre scientifique, 91 - Orsay (France)

2005-07-01

We first recall the scientific basis of inertial fusion and then describe a generic fusion reactor with the different components: the driver, the fusion chamber, the material treatment unit, the target factory and the turbines. We analyse the options proposed at the present time for the driver and for target irradiation scheme giving the state of art for each approach. We conclude by the presentation of LMJ (laser Megajoule) and NIF (national ignition facility) projects. These facilities aim to demonstrate the feasibility of laboratory DT ignition, first step toward Inertial Fusion Energy. (authors)

Fusion Power Deployment

International Nuclear Information System (INIS)

Schmidt, J.A.; Ogden, J.M.

2002-01-01

Fusion power plants could be part of a future portfolio of non-carbon dioxide producing energy supplies such as wind, solar, biomass, advanced fission power, and fossil energy with carbon dioxide sequestration. In this paper, we discuss key issues that could impact fusion energy deployment during the last half of this century. These include geographic issues such as resource availability, scale issues, energy storage requirements, and waste issues. The resource needs and waste production associated with fusion deployment in the U.S. should not pose serious problems. One important feature of fusion power is the fact that a fusion power plant should be locatable within most local or regional electrical distribution systems. For this reason, fusion power plants should not increase the burden of long distance power transmission to our distribution system. In contrast to fusion power, regional factors could play an important role in the deployment of renewable resources such as wind, solar and biomass or fossil energy with CO2 sequestration. We examine the role of these regional factors and their implications for fusion power deployment

Laser fusion overview

International Nuclear Information System (INIS)

Nuckolls, J.

1976-01-01

Because of recent breakthroughs in the target area, and in the glass laser area, the scientific feasibility of laser fusion--and of inertial fusion--may be demonstrated in the early 1980's. Then the development in that time period of a suitable laser (or storage ring or other driving source) would make possible an operational inertial fusion reactor in this century. These are roughly the same time scales as projected by the Tokamak magnetic confinement approach. It thus appears that the 15-20 year earlier start by magnetic confinement fusion may be overcome. Because inertial confinement has been demonstrated, and inertial fusion reactors may operate on smaller scales than Tokamaks, laser fusion may have important technical and economic advantages

Intrusion scenarios in fusion waste disposal sites

International Nuclear Information System (INIS)

Zucchetti, M.; Zucchetti, M.; Rocco, P.

1998-01-01

Results of analyses on human intrusions into repositories of fusion radioactive waste are presented. The main topics are: duration of the institutional control, occurrence of intrusion, intrusion scenarios, acceptable risk limits and probabilistic data. Application to fusion waste repositories is implemented with a computational model: wells drilling is considered as the possible scenario. Doses and risks to intruder for different SEAFP-2 cases turn out to be very small. No intervention to reduce the hazard is necessary. (authors)

Intrusion scenarios in fusion waste disposal sites

Energy Technology Data Exchange (ETDEWEB)

Zucchetti, M. [European Commission, JRC, Institute for Advanced Material, Ispra, Vatican City State, Holy See (Italy); Zucchetti, M.; Rocco, P. [Energetics Dept., Polytechnic of Turin (Italy)

1998-07-01

Results of analyses on human intrusions into repositories of fusion radioactive waste are presented. The main topics are: duration of the institutional control, occurrence of intrusion, intrusion scenarios, acceptable risk limits and probabilistic data. Application to fusion waste repositories is implemented with a computational model: wells drilling is considered as the possible scenario. Doses and risks to intruder for different SEAFP-2 cases turn out to be very small. No intervention to reduce the hazard is necessary. (authors)

Synthetic report 2012. Research programme on controlled thermonuclear fusion; Rapport de synthèse 2012. Programme de recherche Fusion thermonucléaire contrôlée

Energy Technology Data Exchange (ETDEWEB)

Vaucher, C. [Secrétariat à l’éducation et à la recherche (SER), Berne (Switzerland); Tran, M. Q.; Villard, L. [Swiss Federal Institute of Technology EPFL, Lausanne (Switzerland); Marot, L. [University of Basel, Basel (Switzerland)

2013-07-01

Since 1961, Switzerland participates in the research on thermonuclear fusion thanks to the creation of the Research Centre in Plasma Physics. In 1979 it entered into partnership with the European programme on fusion through its adhesion to EURATOM. The thermonuclear fusion is an interesting energy source because the basic fuel is practically inexhaustible and its use does not release any significant CO{sub 2} quantity and very little radioactive residues. But its working up faces enormous physical and technological difficulties. The International Thermonuclear Reactor (ITER), presently in construction, has to demonstrate the technological feasibility of the controlled fusion. Il will be followed by DEMO, foreseen for 2040-2050, which must guarantee the economical rentability. At CRPP the research projects are partitioned onto several sites: at the Swiss Federal Institute of Technology (EPFL) in Lausanne, they concern the physics of the magnetic confinement with the Variable Geometry Tokamak (TCV), the development of theoretical models and the numerical simulation, the plasma heating and the generation of hyper frequency waves; the Paul Scherrer Institute (PSI) studies the superconductivity and the materials; the interactions between the plasma and the Tokamak walls are studied at the Basel University for the structures of ITER. Thanks to its large flexibility, TCV allows the creation and the control of plasmas of very different forms. The injection system of millimetric waves allows orienting the injected power according to specific profiles. By using the asymmetry of the flow in the toroidal sense, the plasma rotation could be measured with a much better accuracy than before. In TCV, by playing on the form of the plasma, it was possible to strongly reduce the energy quantity which is expelled by the Edge Localized Modes (ELM) onto the wall of the vacuum chamber. The ‘snowflake’ configuration created in TCV allows distributing the ELM energy onto several impact

Non-fusion rates in anterior cervical discectomy and implantation of empty polyetheretherketone cages.

Science.gov (United States)

Pechlivanis, Ioannis; Thuring, Theresa; Brenke, Christopher; Seiz, Marcel; Thome, Claudius; Barth, Martin; Harders, Albrecht; Schmieder, Kirsten

2011-01-01

A prospective analysis. Our aim was to assess the radiographically detectable bony fusion in patients with anterior cervical discectomy (ACD) and polyetheretherketone (PEEK)-cage implantation without additional filling. Furthermore, clinical data of patients with and without fusion were compared. PEEK-cage implantation is performed in cervical spinal surgery because of its benefits. However, fusion rates without filling of the cage have not been reported. Patients selected for ACD with PEEK-cage implantation prospectively underwent plain radiography in anterior-posterior and lateral projections during the postoperative hospital stay and at follow-up. Furthermore, clinical status was evaluated using the Odom scale, the Short Form-36, the Visual Analog Scale (VAS) for arm and neck pain, and the cervical Oswestry score. Fusion status, migration, and subsidence of the PEEK cage were evaluated on the basis of the lateral radiographs. Fusion was confirmed by presence of continuous trabecular bone bridges in the disc space. To exclude an influence of the cage on the evaluation of fusion rates, fusion was evaluated in analogous fashion retrospectively in a control group. A total of 52 patients underwent ACD and interbody fusion. One-level surgery was performed in 44 patients and 2-level surgery in 8 patients. A total of 60 ACD and interbody fusions with a PEEK cage were analyzed. A majority of operations were at the C5/6 level (40 patients, 77%). Cage height was 4 mm in 32 cases, 5 mm in 23 cases, and 6 mm in 5 cases. Bony fusion was present at 43 treated levels (71.7%), whereas at 17 levels (28.3%) no fusion was found. Statistical analysis revealed no significant difference between the fusion and non-fusion groups regarding time to follow-up, implanted cage height. Short Form-36, cervical Oswestry score, VAS arm and neck, or Odom criteria. In the control group, ACD was performed in 29 patients (42 levels; 18 one-level and 12 two-level operations). Bony fusion was present

Jamb and jamc are essential for vertebrate myocyte fusion.

Directory of Open Access Journals (Sweden)

Gareth T Powell

2011-12-01

Full Text Available Cellular fusion is required in the development of several tissues, including skeletal muscle. In vertebrates, this process is poorly understood and lacks an in vivo-validated cell surface heterophilic receptor pair that is necessary for fusion. Identification of essential cell surface interactions between fusing cells is an important step in elucidating the molecular mechanism of cellular fusion. We show here that the zebrafish orthologues of JAM-B and JAM-C receptors are essential for fusion of myocyte precursors to form syncytial muscle fibres. Both jamb and jamc are dynamically co-expressed in developing muscles and encode receptors that physically interact. Heritable mutations in either gene prevent myocyte fusion in vivo, resulting in an overabundance of mononuclear, but otherwise overtly normal, functional fast-twitch muscle fibres. Transplantation experiments show that the Jamb and Jamc receptors must interact between neighbouring cells (in trans for fusion to occur. We also show that jamc is ectopically expressed in prdm1a mutant slow muscle precursors, which inappropriately fuse with other myocytes, suggesting that control of myocyte fusion through regulation of jamc expression has important implications for the growth and patterning of muscles. Our discovery of a receptor-ligand pair critical for fusion in vivo has important implications for understanding the molecular mechanisms responsible for myocyte fusion and its regulation in vertebrate myogenesis.

Electromagnetic computations for fusion devices

International Nuclear Information System (INIS)

Turner, L.R.

1989-09-01

Among the difficulties in making nuclear fusion a useful energy source, two important ones are producing the magnetic fields needed to drive and confine the plasma, and controlling the eddy currents induced in electrically conducting components by changing fields. All over the world, researchers are developing electromagnetic codes and employing them to compute electromagnetic effects. Ferromagnetic components of a fusion reactor introduce field distortions. Eddy currents are induced in the vacuum vessel, blanket and other torus components of a tokamak when the plasma current disrupts. These eddy currents lead to large forces, and 3-D codes are being developed to study the currents and forces. 35 refs., 6 figs

Resistive wall mode feedback control in EXTRAP T2R with improved steady-state error and transient response

Science.gov (United States)

Brunsell, P. R.; Olofsson, K. E. J.; Frassinetti, L.; Drake, J. R.

2007-10-01

Experiments in the EXTRAP T2R reversed field pinch [P. R. Brunsell, H. Bergsåker, M. Cecconello et al., Plasma Phys. Control. Fusion 43, 1457 (2001)] on feedback control of m =1 resistive wall modes (RWMs) are compared with simulations using the cylindrical linear magnetohydrodynamic model, including the dynamics of the active coils and power amplifiers. Stabilization of the main RWMs (n=-11,-10,-9,-8,+5,+6) is shown using modest loop gains of the order G ˜1. However, other marginally unstable RWMs (n=-2,-1,+1,+2) driven by external field errors are only partially canceled at these gains. The experimental system stability limit is confirmed by simulations showing that the latency of the digital controller ˜50μs is degrading the system gain margin. The transient response is improved with a proportional-plus-derivative controller, and steady-state error is improved with a proportional-plus-integral controller. Suppression of all modes is obtained at high gain G ˜10 using a proportional-plus-integral-plus-derivative controller.

Environmental and safety issues of the fusion fuel cycle

International Nuclear Information System (INIS)

Crocker, J.G.

1980-01-01

This paper discusses the environmental and safety concerns inherent in the development of fusion energy, and the current Department of Energy programs seeking to: (1) develop safe and reliable techniques for tritium control; (2) reduce the quantity of activation products produced; and (3) provide designs to limit the potential for accidents that could result in release of radioactive materials. Because of the inherent safety features of fusion and the early start that has been made in safety problem recognition and solution, fusion should be among the lower risk technologies for generation of commercial power

Membrane fusion

DEFF Research Database (Denmark)

Bendix, Pól Martin

2015-01-01

At Stanford University, Boxer lab, I worked on membrane fusion of small unilamellar lipid vesicles to flat membranes tethered to glass surfaces. This geometry closely resembles biological systems in which liposomes fuse to plasma membranes. The fusion mechanism was studied using DNA zippering...... between complementary strands linked to the two apposing membranes closely mimicking the zippering mechanism of SNARE fusion complexes....

A virtual test of screening technology based on the AGEIA PhysX

Energy Technology Data Exchange (ETDEWEB)

Ai-min Li; Rui-ling Lv; Chu-sheng Liu [China University of Mining and Technology, Xuzhou (China). School of Mechanical and Electrical Engineering

2008-06-15

The authors have created a virtual test of vibration particle-screening using Autodesk's 3ds Max software, the MAXScript scripting language and the AGEIA PhysX physics processing unit (PPU). The affect of various parameters on screening efficiency were modeled. The parameters included vibration amplitude, frequency and direction. The length and inclination of the vibrating surface were also varied. The virtual experiment is in basic agreement with results predicted from screening theory. This shows that the virtual screener can be used for preliminary investigations and the results used to evaluate screen design. In addition it can help with theoretical research. 11 refs., 7 figs., 7 tabs.

Controlled chondrogenesis from adipose-derived stem cells by recombinant transforming growth factor-β3 fusion protein in peptide scaffolds.

Science.gov (United States)

Zheng, Dong; Dan, Yang; Yang, Shu-hua; Liu, Guo-hui; Shao, Zeng-wu; Yang, Cao; Xiao, Bao-jun; Liu, Xiangmei; Wu, Shuilin; Zhang, Tainjin; Chu, Paul K

2015-01-01

Adipose-derived stem cells (ADSCs) are promising for cartilage repair due to their easy accessibility and chondrogenic potential. Although chondrogenesis of transforming growth factor-β (TGF-β) mediated mesenchymal stem cells (MSCs) is well established in vitro, clinical tissue engineering requires effective and controlled delivery of TGF-β in vivo. In this work, a self-assembled peptide scaffold was employed to construct cartilages in vivo through the chondrogenesis from ADSCs controlled by recombinant fusion protein LAP-MMP-mTGF-β3 that was transfected by lentiviral vectors. During this course, the addition of matrix metalloproteinases (MMPs) can trigger the release of mTGF-β3 from the recombinant fusion protein of LAP-MMP-mTGF-β3 in the combined scaffolds, thus stimulating the differentiation of ADSCs into chondrogenesis. The specific expression of cartilage genes was analyzed by real-time polymerase chain reaction and Western blot. The expression of chondrocytic markers was obviously upregulated to a higher level compared to the one by commonly used TGF-β3 alone. After 3 weeks of in vitro culturing, the hybrids with differentiated chondrogenesis were then injected subcutaneously into nude mice and retrieved after 4 weeks of culturing in vivo. Histological analysis also confirmed that the recombinant fusion protein was more effective for the formation of cartilage matrix than the cases either with TGF-β3 alone or without LAP-MMP-mTGF-β3 (P<0.05). This study demonstrates that controlled local delivery of the LAP-MMP-mTGF-β3 constructs can accelerate differentiation of ADSCs into the cartilage in vivo, which indicates the great potential of this hybrid in rapid therapy of osteoarthritis. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Fusion: from sacred cow to white elephant?

International Nuclear Information System (INIS)

Wooldridge, J.

1994-01-01

Controlled thermonuclear fusion has the potential to supply lots of relatively cheap power relatively cheaply. It is also renewable and has public support. Because of this potential, fusion has been able to attract huge research funds. The four main research programmes, in Europe, USA, Japan and Russia, include cooperation on the International Thermonuclear Experimental Reactor, ITER. The siting of this reactor will be decided in 1998 and it is due to start operation in 2010. It should lead to a demonstration reactor, DEMO, after which a prototype commercial reactor is envisaged for 2030-2050. But this is too far away to solve some of the immediate energy problems such as carbon dioxide emissions and global warming. So even if the technical problems are solved, fusion may not be the wonder energy source when it finally arrives; the trend is away from centralised, high cost, high output generation. Fusion research has taken interest and money away from other alternatives such as tidal energy, fuel cells and photovoltaic cells. Photovoltaics in particular look more feasible than fusion and could be in place far sooner, but lack the funding for research. (UK)

Fusion plasma physics during half a century

Energy Technology Data Exchange (ETDEWEB)

Lehnert, Bo

1999-08-01

A review is given on the potentialities of fusion energy with respect to energy production and related environmental problems, the various approaches to controlled thermonuclear fusion, the main problem areas of research, the historical development, the present state of investigations, and future perspectives. This article also presents a personal memorandum of the author. Thereby special reference will be given to part of the research conducted at the Royal Institute of Technology in Stockholm, merely to identify its place within the general historical development. Considerable progress has been made in fusion research during the last decades. In large tokamak experiments temperatures above the ignition limit of about 10{sup 8} K have been reached under break-even conditions where the fusion power generation is comparable to the energy loss. A power producing fusion reactor could in principle be realized already today, but it would not become technically and economically efficient. The future international research programme has therefore to be conducted along broad lines, with necessary ingredients of basis research and new ideas, and also within lines of magnetic confinement being alternative to that of tokamaks.

Comment on “Effects of damping solitary wave in a viscosity bounded plasma” [Phys. Plasmas 21, 022118 (2014)

Energy Technology Data Exchange (ETDEWEB)

Ghosh, Uday Narayan, E-mail: unghosh1@rediffmail.com; Chatterjee, Prasanta; Roychoudhury, Rajkumar [Department of Mathematics, Siksha Bhavana, Visva Bharati, Santiniketan 731235 (India)

2015-07-15

Recently Gun Li et al. discussed “Effects of damping solitary wave in a viscosity bounded plasma” [Phys. Plasmas 21, 022118 (2014)]. The paper contains some serious errors which have been pointed out in this Comment.

Vacuum engineering for fusion research and fusion reactors

International Nuclear Information System (INIS)

Pittenger, L.C.

1976-01-01

The following topics are described: (1) surface pumping by cryogenic condensation, (2) operation of large condensing cryopumps, (3) pumping for large fusion experiments, and (4) vacuum technology for fusion reactors

Nuclear fusion

International Nuclear Information System (INIS)

Al-zaelic, M.M.

2013-01-01

Nuclear fusion can be relied on to solve the global energy crisis if the process of limiting the heat produced by the fusion reaction (Plasma) is successful. Currently scientists are progressively working on this aspect whereas there are two methods to limit the heat produced by fusion reaction, the two methods are auto-restriction using laser beam and magnetic restriction through the use of magnetic fields and research is carried out to improve these two methods. It is expected that at the end of this century the nuclear fusion energy will play a vital role in overcoming the global energy crisis and for these reasons, acquiring energy through the use of nuclear fusion reactors is one of the most urge nt demands of all mankind at this time. The conclusion given is that the source of fuel for energy production is readily available and inexpensive ( hydrogen atoms) and whole process is free of risks and hazards, especially to general health and the environment . Nuclear fusion importance lies in the fact that energy produced by the process is estimated to be about four to five times the energy produced by nuclear fission. (author)

Radiation resistant organic composites for superconducting fusion magnets

International Nuclear Information System (INIS)

Nishijima, S.; Okada, T.

1993-01-01

Organic composite materials (usually reinforced by glas fibers: GFRP) are to be used in fusion superconducting magnets as insulating and/or structural materials. The fusion superconducting magnets are operated under radiation environments and hence the radiation induced degradation of magnet components is ought to be estimated. Among the components the organic composite materials were evaluated to be the most radiation sensitive. Consequently the development of radiation resistant organic composite materials is thought one of the 'key' technologies for fusion superconducting magnets. The mechanism of radiation-induced degradation was studied and the degradation of interlaminar shear strength (ILSS) was found to be the intrinsic phenomenon which controlled the overall degradation of organic composite materials. The degradation of ILSS was studied changing matrix resin, reinforcement and type of fabrics. The possible combination of the organic composites for the fusion superconducting magnet will be discussed. (orig.)

Circumferential fusion improves outcome in comparison with instrumented posterolateral fusion

DEFF Research Database (Denmark)

Videbaek, Tina S; Christensen, Finn B; Soegaard, Rikke

2006-01-01

with respect to all four DPQ categories: daily activities, work/leisure, anxiety/depression, and social interest. The Oswestry Disability Index supported these results (P ...STUDY DESIGN: Prospective randomized clinical study with a 5- to 9-year follow-up period. OBJECTIVE: The aim of the present study was to analyze the long-term outcome with respect to functional disability, pain, and general health of patients treated by means of circumferential lumbar fusion...... in comparison with those treated by means of instrumented posterolateral lumbar fusion. SUMMARY OF BACKGROUND DATA: Circumferential fusion has become a common procedure in lumbar spinal fusion both as a primary and salvage procedure. However, the claimed advantages of circumferential fusion over conventional...

Comment on ‘A new method for fusion, denoising and enhancement of x-ray images retrieved from Talbot–Lau grating interferometry’

International Nuclear Information System (INIS)

Scholkmann, Felix; Revol, Vincent; Kaufmann, Rolf; Kottler, Christian

2015-01-01

In a recent paper (Scholkamm et al 2014 Phys. Med. Biol. 59 1425–40) we presented a new image denoising, fusion and enhancement framework for combining and optimal visualization of x-ray attenuation contrast, differential phase contrast and dark-field contrast images retrieved from x-ray Talbot–Lau grating interferometry. In this comment we give additional information and report about the application of our framework to breast cancer tissue which we presented in our paper as an example. The applied procedure is suitable for a qualitative comparison of different algorithms. For a quantitative juxtaposition original data would however be needed as an input. (comment and reply)

Incomplete fusion studies

International Nuclear Information System (INIS)

Singh, B.P.

2011-01-01

In order to study the incomplete fusion reaction dynamics at energies ≅ 4-7 MeV/nucleon, several experiments have been carried out using accelerator facilities available in India. The measurements presented here cover a wide range of projectile-target combinations and enhance significantly our knowledge about incomplete fusion reaction dynamics. Here, the three sets of measurements have been presented; (i) excitation functions, (ii) forward recoil range distributions and (iii) the spin distributions. The first evidence of these reactions has been obtained from the measurement and analysis of excitation functions for xn/αxn/2αxn-channels. The measured excitation functions have been analyzed within the framework of compound nucleus model. The results obtained indicate the occurrence of fusion incompleteness at low beam energies. However, in order to determine the relative contribution of complete and incomplete fusion reaction processes, the recoil range distributions of the heavy residues have also been measured and analyzed within the framework of breakup fusion model which confirmed the fusion incompleteness in several heavy ion reactions involving α-emitting reaction channels. Further, in order to study the role of l-values in these reactions the spin distributions of the residues populated in case of complete and incomplete channels have been measured and are found to be distinctly different. The analysis of the data on spin distribution measurements indicate that the mean values of driving input angular momenta associated with direct-α-emitting (incomplete fusion) channels are higher than that observed for fusion-evaporation xn or α-emitting (complete fusion) channels, and is found to increase with direct α-multiplicity in the forward cone. One of the important conclusions drawn in the present work is that, there is significant incomplete fusion contribution even at energies slightly above the barrier. Further, the projectile structure has been found to

Robust adaptive control of the sawtooth instability in nuclear fusion

NARCIS (Netherlands)

Bolder, J.J.; Witvoet, G.; Baar, de M.R.; Wouw, van de N.; Haring, M.A.M.; Westerhof, E.; Doelman, N.J.; Steinbuch, M.

2012-01-01

The sawtooth instability is a repetitive phenomenon occurring in plasmas of tokamak nuclear fusion reactors. Experimental studies of these instabilities and the effect they have on the plasma (notably the drive of secondary instabilities and consequent performance reduction) for a wide variety of

Alushta-2012. International Conference-School on Plasma Physics and Controlled Fusion and the Adjoint Workshop 'Nano-and micro-sized structures in plasmas'. Book of Abstracts

International Nuclear Information System (INIS)

Makhlaj, V.A.

2012-01-01

The Conference was devoted to a new valuable information about the present status of plasma physics and controlled fusion research. The main topics was : magnetic confinement systems; plasma heating and current drive; ITER and fusion reactor aspects; basic plasma physics; space plasma; plasma dynamics and plasma-wall interaction; plasma electronics; low temperature plasma and plasma technologies; plasma diagnostics; formation of nano-and micro-sized structures in plasmas; properties of plasmas with nano- and micro- objects

Control of molten salt corrosion of fusion structural materials by metallic beryllium

International Nuclear Information System (INIS)

Calderoni, P.; Sharpe, P.; Nishimura, H.; Terai, T.

2009-01-01

A series of tests have been performed between 2001 and 2006 at the Safety and Tritium Applied Research facility of the Idaho National Laboratory to demonstrate chemical compatibility between the molten salt flibe (2LiF + BeF 2 in moles) and fusion structural materials once suitable fluoride potential control methods are established. The tests adopted metallic beryllium contact as main fluoride potential control, and the results have been published in recent years. A further step was to expose two specimens of low activation ferritic/martensitic steel 9Cr-2W to static corrosion tests that include an active corrosion agent (hydrofluoric gas) in controlled conditions at 530 deg. C, and the results of the tests are presented in this paper. The results confirmed the expected correlation of the HF recovery with the concentration of metallic impurities dissolved in the salt because of specimen corrosion. The metals concentration dropped to levels close to the detectable limit when the beryllium rod was inserted and increased once the content of excess beryllium in the system had been consumed by HF reduction and specimen corrosion progressed. Metallographic analysis of the samples after 500 h exposure in reactive conditions showed evidence of the formation of unstable chromium oxide layers on the specimen's surface.

Progress in fusion technology in the U.S. magnetic fusion program

International Nuclear Information System (INIS)

Dowling, R.J.; Beard, D.S.; Haas, G.M.; Stone, P.M.; George, T.V.

1987-01-01

In this paper the authors discuss the major technological achievements that have taken place during the past few years in the U.S. magnetic fusion program which have contributed to the global efforts. The goal has been to establish the scientific and technological base required for fusion energy. To reach this goal the fusion RandD program is focused on four key technical issues: determine the optimum configuration of magnetic confinement systems; determine the properties of burning plasmas; develop materials for fusion systems; and establish the nuclear technology of fusion systems. The objective of the fusion technology efforts has been to develop advanced technologies and provide the necessary support for research of these four issues. This support is provided in a variety of areas such as: high vacuum technology, large magnetic field generation by superconducting and copper coils, high voltage and high current power supplies, electromagnetic wave and particle beam heating systems, plasma fueling, tritium breeding and handling, remote maintenance, energy recovery. The U.S. Fusion Technology Program provides major support or has the primary responsibility in each of the four key technical issues of fusion, as described in the Magnetic Fusion Program Plan of February 1985. This paper has summarized the Technology Program in terms of its activities and progress since the Proceedings of the SOFT Conference in 1984

Fusion reactor development using high power particle beams

International Nuclear Information System (INIS)

Ohara, Y.

1990-01-01

The present paper outlines major applications of the ion source/accelerator to fusion research and also addresses the present status and future plans for accelerator development. Applications of ion sources/accelerators for fusion research are discussed first, focusing on plasma heating, plasma current drive, plasma current profile control, and plasma diagnostics. The present status and future plan of ion sources/accelerators development are then described focusing on the features of existing and future tokamak equipment. Positive-ion-based NBI systems of 100 keV class have contributed to obtaining high temperature plasmas whose parameters are close to the fusion break-even condition. For the next tokamak fusion devices, a MeV class high power neutral beam injector, which will be used to obtain a steady state burning plasma, is considered to become the primary heating and current drive system. Development of such a system is a key to realize nuclear fusion reactor. It will be entirely indebted to the development of a MeV class high current negative deuterium ion source/accelerator. (N.K.)

Participation of the Instituto de Pesquisas Espaciais in the national program for plasma physics and controlled thermonuclear fusion

International Nuclear Information System (INIS)

1990-01-01

This is a report concerning the participation of the Instituto de Pesquisas Espaciais in the national program for plasma physics and controlled thermonuclear fusion. The report lists all the personnel enroled in research activities, both theoretical and experimental. The research subjects are the following: relativistic electron beams; plasma produced by laser; plasma theory; quiescent plasma; plasma centrifugal; ionic propulsion. (A.C.A.S.) [pt

FuzzyFusion: an application architecture for multisource information fusion

Science.gov (United States)

Fox, Kevin L.; Henning, Ronda R.

2009-04-01

The correlation of information from disparate sources has long been an issue in data fusion research. Traditional data fusion addresses the correlation of information from sources as diverse as single-purpose sensors to all-source multi-media information. Information system vulnerability information is similar in its diversity of sources and content, and in the desire to draw a meaningful conclusion, namely, the security posture of the system under inspection. FuzzyFusionTM, A data fusion model that is being applied to the computer network operations domain is presented. This model has been successfully prototyped in an applied research environment and represents a next generation assurance tool for system and network security.

Applications of high-speed dust injection to magnetic fusion

International Nuclear Information System (INIS)

Wang, Zhehui; Li, Yangfang

2012-01-01

It is now an established fact that a significant amount of dust is produced in magnetic fusion devices due to plasma-wall interactions. Dust inventory must be controlled, in particular for the next-generation steady-state fusion machines like ITER, as it can pose significant safety hazards and degrade performance. Safety concerns are due to tritium retention, dust radioactivity, toxicity, and flammability. Performance concerns include high-Z impurities carried by dust to the fusion core that can reduce plasma temperature and may even induce sudden termination of the plasma. We have recognized that dust transport, dust-plasma interactions in magnetic fusion devices can be effectively studied experimentally by injection of dust with known properties into fusion plasmas. Other applications of injected dust include diagnosis of fusion plasmas and edge localized mode (ELM)'s pacing. In diagnostic applications, dust can be regarded as a source of transient neutrals before complete ionization. ELM's pacing is a promising scheme to prevent disruptions and type I ELM's that can cause catastrophic damage to fusion machines. Different implementation schemes are available depending on applications of dust injection. One of the simplest dust injection schemes is through gravitational acceleration of dust in vacuum. Experiments at Los Alamos and Princeton will be described, both of which use piezoelectric shakers to deliver dust to plasma. In Princeton experiments, spherical particles (40 micron) have been dropped in a systematic and reproducible manner using a computer-controlled piezoelectric bending actuator operating at an acoustic (0,2) resonance. The circular actuator was constructed with a 2.5 mm diameter central hole. At resonance (∼ 2 kHz) an applied sinusoidal voltage has been used to control the flux of particles exiting the hole. A simple screw throttle located ∼1mm above the hole has been used to set the magnitude of the flux achieved for a given voltage

Structural materials challenges for fusion power systems

International Nuclear Information System (INIS)

Kurtz, Richard J.

2009-01-01

Full text: Structural materials in a fusion power system must function in an extraordinarily demanding environment that includes various combinations of high temperatures, reactive chemicals, time-dependent thermal and mechanical stresses, and intense damaging radiation. The fusion neutron environment produces displacement damage equivalent to displacing every atom in the material about 150 times during its expected service life, and changes in chemical composition by transmutation reactions, which includes creation of reactive and insoluble gases. Fundamental materials challenges that must be resolved to effectively harness fusion power include (1) understanding the relationships between material strength, ductility and resistance to cracking, (2) development of materials with extraordinary phase stability, high-temperature strength and resistance to radiation damage, (3) establishment of the means to control corrosion of materials exposed to aggressive environments, (4) development of technologies for large-scale fabrication and joining, and (5) design of structural materials that provide for an economically attractive fusion power system while simultaneously achieving safety and environmental acceptability goals. The most effective approach to solve these challenges is a science-based effort that couples development of physics-based, predictive models of materials behavior with key experiments to validate the models. The U.S. Fusion Materials Sciences program is engaged in an integrated effort of theory, modeling and experiments to develop structural materials that will enable fusion to reach its safety, environmental and economic competitiveness goals. In this presentation, an overview of recent progress on reduced activation ferritic/martensitic steels, nanocomposited ferritic alloys, and silicon carbide fiber reinforced composites for fusion applications will be given

An Indispensable Truth How Fusion Power Can Save the Planet

CERN Document Server

Chen, Francis F

2011-01-01

Both global warming and oil shortage can be solved by controlled fusion, a clean power source that will serve mankind for millennia.� The idea of hydrogen fusion as well as its difficulties are presented in non-technical language to dispel the notion that fusion is always 50 years away.� This book also summarizes the evidence for climate change and explains the principles of both fossil and "green" energy sources to show that fusion is the best alternative for central-station power in the near term as well as the far future. Praise for An Indispensable Truth: How Fusion Power Can Save the Planet: "In this study Professor Chen outlines the underlying physics, recent progress in achieving advanced plasmas and magnetic confinement, and hopes for the future. He recognizes the difficulties that remain in engineering a fusion reactor, but he remains optimistic regarding ultimate success, yet fearful of the consequences were we to fail."- James R. Schlesinger, former Chairman, Atomic Energy Commission; Director,...

Decontamination of lead by fusion (1962); Decontamination du plomb par fusion (1962)

Energy Technology Data Exchange (ETDEWEB)

Boutot, P; Giachetto, L; Capitaine, A [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

1962-07-01

Various attempts to decontaminate using mechanical and chemical methods having given questionable results, a fusion method has been developed. The apparatus consists of a propane-heated oven fitted with a steel crucible of 1 400 kg capacity, with two ventilation systems, and with a vacuum gauge for preventing the diffusion of toxic gases. There are three operational controls : 1. On the samples taken before during and after the operation, 2. On the plugs taken from the ingots, 3. On the ingot itself. The continuous sanitary control is done by a radioactive aerosol recorder and by periodic sampling. This decontamination process will be improved, especially as far as the productivity and the safety precautions are concerned. (authors) [French] Divers essais de decontamination par voies mecaniques et chimiques ayant donne des resultats discutables, un procede par fusion a ete mis au point. L'appareil se compose d'un four, chauffe au propane, muni d'un creuset en acier d'une capacite de 1 400 kg, de deux systemes de ventilation et d'un deprimometre afin d'eviter la diffusion de vapeurs nocives. Trois controles d'activite sont effectues: 1. sur des echantillons preleves avant, pendant et apres l'operation, 2. sur des carottages realises sur les lingots, 3. sur le lingot lui-meme. Le controle sanitaire permanent est assure par un enregistreur d'aerosols radioactifs et par des prelevements periodiques. Ce procede de decontamination doit encore etre ameliore, principalement en ce qui concerne la productivite et la securite. (auteurs)

Control of molten salt corrosion of reduced activation steel for fusion applications by metallic beryllium