MOD-5A wind turbine generator program design report: Volume 1: Executive Summary

Science.gov (United States)

1984-01-01

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator covering work performed between July 1980 and June 1984 is discussed. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 1, the Executive Summary, summarizes all phases of the MOD-5A program. The performance and cost of energy generated by the MOD-5A are presented. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation, power generation, and control and instrumentation subsystems - is described briefly. The early phases of the MOD-5A program, during which the design was analyzed and optimized, and new technologies and materials were developed, are discussed. Manufacturing, quality assurance, and safety plans are presented. The volume concludes with an index of volumes 2 and 3.

Magnetic phase diagram of Co(Cr1-xA lx) 2O4 (x = 0.0-1.0)

Science.gov (United States)

Padam, R.; Sarkar, T.; Mathieu, R.; Thota, S.; Pal, D.

2017-08-01

We report the role of Al substitution in the magnetic properties of spinel CoCr2O4 by means of temperature dependent dc and ac magnetization and heat capacity measurements. Various compositions (0.0 ≤ x ≤ 1.0) of polycrystalline Co(Cr1-xAlx)2O4 samples have been prepared by sol-gel processing and their crystal structure was investigated by X-ray diffraction which was found to crystallize in the normal cubic spinel structure. For x ≤ 0.1, the system exhibits multiple magnetic orderings (long range ferrimagnetic ordering TC, spin-spiral ordering TS, and lock-in transition TL), similar to that of the parent compound, CoCr2O4. However, all the compositions between x = 0.1 and 0.5 exhibit long range ferrimagnetic ordering below TC and also a short range order at low temperature. Spin-glass like ordering was noticed between x = 0.6 and 0.8 due to the diluted B-site occupancy, whereas the end compound CoAl2O4 (x = 1.0) shows antiferromagnetic behavior. On the basis of these results, we propose a magnetic phase diagram for the Co(Cr1-xAlx)2O4 series as a function of the Al content (x) and measuring temperature (T).

Phase diagram of ZnCr2pA12-2pS(Se)4 and Zn1-pCdpCr2S(Se)4

International Nuclear Information System (INIS)

Afif, K.; Benyoussef, A.; Hamedoun, M.; Hourmatallah, A.

1999-06-01

We compute the phase diagram of the nonmetallic compounds ZnCr2 p A1 2-2p S(Se) 4 (I[S,Se]) and Zn 1-p Cd p Cr 2 S(Se) 4 (II[S,Se]). We consider the bond-diluted Ising model on the spinel B site (S.B.S.) lattice with competitive exchange interactions, i.e. the ferromagnetic exchange interaction J 1 between nearest neighbours (n.n.) and the antiferromagnetic superexchange interaction J 2 between next-nearest neighbours' (n.n.n.) (and/or the more distant superexchange interactions J i (i > 1). Dilution and competition are found to be responsible for the spill glass phase and the percolation behaviour. (author)

Microstructure, crystal structure and electrical properties of Cu0.1Ni0.8Co0.2Mn1.9O4 ceramics obtained at different sintering conditions

International Nuclear Information System (INIS)

Bodak, O.; Akselrud, L.; Demchenko, P.; Kotur, B.; Mrooz, O.; Hadzaman, I.; Shpotyuk, O.; Aldinger, F.; Seifert, H.; Volkov, S.; Pekhnyo, V.

2002-01-01

Details of the formation of Cu 0.1 Ni 0.8 Co 0.2 Mn 1.9 O 4 ceramics under different sintering conditions have been studied by optical microscopy, scanning electron microscopy (SEM), electron probe and energy dispersive spectroscopy (EDX) microanalyses, X-ray diffraction (XRD) and electrical resistivity measurements. Microstructure studies of samples sintered at 1170 deg. C for 1 h indicated the presence of a secondary phase besides the main spinel phase with modified composition. XRD measurements showed that the spinel phase exhibits a tetragonally distorted spinel structure (space group I4 1 /amd, a=5.9410(5) A, c=8.4196(15) A). The secondary phase (solid solution based on NiO) crystallizes with the NaCl-type structure (space group Fm3-bar m, a=4.1872(3) A). The content of the secondary phase in ceramics is 10.61 mass%. For NiMn 2 O 4 ceramics, prepared under the same sintering conditions, the decomposition with Ni 1-x Mn x O solid solution (NaCl-type structure) and spinel phase formation have been observed. The tetragonal modification of the spinel phase for NiMn 2 O 4 ceramics is more preferable (space group I4 1 /amd, a=5.9764(5) A, c=8.4201(8) A). The distribution of atoms in the structure has been proposed for both ceramics. According to XRD results the Cu 0.1 Ni 0.8 Co 0.2 Mn 1.9 O 4 ceramic samples, sintered at 920 deg. C for 8 h (program 1), at 920 deg. C for 8 h and at 750 deg. C for 24 h (program 2), at 920 deg. C for 8 h, at 1200 deg. C for 1 h and at 920 deg. C for 24 h (program 3) and at 920 deg. C for 8 h, at 1200 deg. C for 1 h, at 920 deg. C for 24 h and at 750 deg. C for 48 h (program 4), contain a single phase with the cubic spinel structure (space group Fd3-bar m). Small residuals of the secondary phase for the ceramics, prepared via programs 3 and 4, have been observed by SEM investigations. The structure transformations of the spinel phase for Cu 0.1 Ni 0.8 Co 0.2 Mn 1.9 O 4 ceramics sintered at 1170 deg. C are attributed to a Jahn

Correlative theoretical and experimental investigation of the formation of AlYB_1_4 and competing phases

International Nuclear Information System (INIS)

Hunold, Oliver; Chen, Yen-Ting; Music, Denis; Baben, Moritz to; Achenbach, Jan-Ole; Keuter, Philipp; Schneider, Jochen M.; Persson, Per O. Å.; Primetzhofer, Daniel

2016-01-01

The phase formation in the boron-rich section of the Al-Y-B system has been explored by a correlative theoretical and experimental research approach. The structure of coatings deposited via high power pulsed magnetron sputtering from a compound target was studied using elastic recoil detection analysis, electron energy loss spectroscopy spectrum imaging, as well as X-ray and electron diffraction data. The formation of AlYB_1_4 together with the (Y,Al)B_6 impurity phase, containing 1.8 at. % less B than AlYB_1_4, was observed at a growth temperature of 800 °C and hence 600 °C below the bulk synthesis temperature. Based on quantum mechanical calculations, we infer that minute compositional variations within the film may be responsible for the formation of both icosahedrally bonded AlYB_1_4 and cubic (Y,Al)B_6 phases. These findings are relevant for synthesis attempts of all boron rich icosahedrally bonded compounds with the space group: Imma that form ternary phases at similar compositions.

Precipitation of T1 and θ′ Phase in Al-4Cu-1Li-0.25Mn During Age Hardening: Microstructural Investigation and Phase-Field Simulation

Science.gov (United States)

Häusler, Ines; Schwarze, Christian; Bilal, Muhammad Umer; Valencia Ramirez, Daniela; Hetaba, Walid; Darvishi Kamachali, Reza; Skrotzki, Birgit

2017-01-01

Experimental and phase field studies of age hardening response of a high purity Al-4Cu-1Li-0.25Mn-alloy (mass %) during isothermal aging are conducted. In the experiments, two hardening phases are identified: the tetragonal θ′ (Al2Cu) phase and the hexagonal T1 (Al2CuLi) phase. Both are plate shaped and of nm size. They are analyzed with respect to the development of their size, number density and volume fraction during aging by applying different analysis techniques in TEM in combination with quantitative microstructural analysis. 3D phase-field simulations of formation and growth of θ′ phase are performed in which the full interfacial, chemical and elastic energy contributions are taken into account. 2D simulations of T1 phase are also investigated using multi-component diffusion without elasticity. This is a first step toward a complex phase-field study of T1 phase in the ternary alloy. The comparison between experimental and simulated data shows similar trends. The still unsaturated volume fraction indicates that the precipitates are in the growth stage and that the coarsening/ripening stage has not yet been reached. PMID:28772481

Dux4 induces cell cycle arrest at G1 phase through upregulation of p21 expression

International Nuclear Information System (INIS)

Xu, Hongliang; Wang, Zhaoxia; Jin, Suqin; Hao, Hongjun; Zheng, Lemin; Zhou, Boda; Zhang, Wei; Lv, He; Yuan, Yun

2014-01-01

Highlights: • Dux4 induced TE671 cell proliferation defect and G1 phase arrest. • Dux4 upregulated p21 expression without activating p53. • Silencing p21 rescued Dux4 mediated proliferation defect and cell cycle arrest. • Sp1 binding site was required for Dux4-induced p21 promoter activation. - Abstract: It has been implicated that Dux4 plays crucial roles in development of facioscapulohumeral dystrophy. But the underlying myopathic mechanisms and related down-stream events of this retrogene were far from clear. Here, we reported that overexpression of Dux4 in a cell model TE671 reduced cell proliferation rate, and increased G1 phase accumulation. We also determined the impact of Dux4 on p53/p21 signal pathway, which controls the checkpoint in cell cycle progression. Overexpression of Dux4 increased p21 mRNA and protein level, while expression of p53, phospho-p53 remained unchanged. Silencing p21 rescued Dux4 mediated proliferation defect and cell cycle arrest. Furthermore, we demonstrated that enhanced Dux4 expression increased p21 promoter activity and elevated expression of Sp1 transcription factor. Mutation of Sp1 binding site decreased dux4 induced p21 promoter activation. Chromatin immunoprecipitation (ChIP) assays confirmed the Dux4-induced binding of Sp1 to p21 promoter in vivo. These results suggest that Dux4 might induce proliferation inhibition and G1 phase arrest through upregulation of p21

Dux4 induces cell cycle arrest at G1 phase through upregulation of p21 expression

Energy Technology Data Exchange (ETDEWEB)

Xu, Hongliang; Wang, Zhaoxia; Jin, Suqin; Hao, Hongjun [Department of Neurology, Peking University First Hospital, Beijing 100034 (China); Zheng, Lemin [The Institute of Cardiovascular Sciences, Peking University Health Science Center, Key Laboratory of Molecular Cardiovascular Sciences of Education Ministry, Key Laboratory of Cardiovascular Molecular Biology and Regulatory Peptides of Health Ministry, Beijing 100191 (China); Zhou, Boda [The Department of Cardiology, Peking University Third Hospital, Beijing 100191 (China); Zhang, Wei; Lv, He [Department of Neurology, Peking University First Hospital, Beijing 100034 (China); Yuan, Yun, E-mail: yuanyun2002@sohu.com [Department of Neurology, Peking University First Hospital, Beijing 100034 (China)

2014-03-28

Highlights: • Dux4 induced TE671 cell proliferation defect and G1 phase arrest. • Dux4 upregulated p21 expression without activating p53. • Silencing p21 rescued Dux4 mediated proliferation defect and cell cycle arrest. • Sp1 binding site was required for Dux4-induced p21 promoter activation. - Abstract: It has been implicated that Dux4 plays crucial roles in development of facioscapulohumeral dystrophy. But the underlying myopathic mechanisms and related down-stream events of this retrogene were far from clear. Here, we reported that overexpression of Dux4 in a cell model TE671 reduced cell proliferation rate, and increased G1 phase accumulation. We also determined the impact of Dux4 on p53/p21 signal pathway, which controls the checkpoint in cell cycle progression. Overexpression of Dux4 increased p21 mRNA and protein level, while expression of p53, phospho-p53 remained unchanged. Silencing p21 rescued Dux4 mediated proliferation defect and cell cycle arrest. Furthermore, we demonstrated that enhanced Dux4 expression increased p21 promoter activity and elevated expression of Sp1 transcription factor. Mutation of Sp1 binding site decreased dux4 induced p21 promoter activation. Chromatin immunoprecipitation (ChIP) assays confirmed the Dux4-induced binding of Sp1 to p21 promoter in vivo. These results suggest that Dux4 might induce proliferation inhibition and G1 phase arrest through upregulation of p21.

SRNL PHASE 1 Assessment Of The WTP Waste Qualification Program

International Nuclear Information System (INIS)

Peeler, D.; Hansen, E.; Herman, C.; Marra, S.; Wilmarth, B.

2012-01-01

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) Project is currently transitioning its emphasis from an engineering design and construction phase toward facility completion, start-up and commissioning. With this transition, the WTP Project has initiated more detailed assessments of the requirements that must be met during the actual processing of the Hanford Site tank waste. One particular area of interest is the waste qualification program. In general, the waste qualification program involves testing and analysis to demonstrate compliance with waste acceptance criteria, determine waste processability, and demonstrate laboratory-scale unit operations to support WTP operations. The testing and analysis are driven by data quality objectives (DQO) requirements necessary for meeting waste acceptance criteria for transfer of high-level wastes from the tank farms to the WTP, and for ensuring waste processability including proper glass formulations during processing within the WTP complex. Given the successful implementation of similar waste qualification efforts at the Savannah River Site (SRS) which were based on critical technical support and guidance from the Savannah River National Laboratory (SRNL), WTP requested subject matter experts (SMEs) from SRNL to support a technology exchange with respect to waste qualification programs in which a critical review of the WTP program could be initiated and lessons learned could be shared. The technology exchange was held on July 18-20, 2011 in Richland, Washington, and was the initial step in a multi-phased approach to support development and implementation of a successful waste qualification program at the WTP. The 3-day workshop was hosted by WTP with representatives from the Tank Operations Contractor (TOC) and SRNL in attendance as well as representatives from the US DOE Office of River Protection (ORP) and the Defense Nuclear Facility Safety Board (DNFSB) Site Representative office. The purpose of the

Synthesis and crystal structure of nanocrystalline phase: Ca1-xMxZr4P6O24 (M = Sr, Ba and x = 0.0-1.0)

International Nuclear Information System (INIS)

Rashmi, Ch.; Shrivastava, O.P.

2011-01-01

The structure of strontium and barium substituted nano crystalline calcium zirconium phosphate (CZP) was determined on the basis of crystal data of solid solutions. It was found that up to 2.42 mol % of strontium and 1.62 mol % of barium could be loaded into CZP formulations without significant changes of the three-dimensional framework structure. The crystal chemistry of Ca 1-x M x Zr 4 P 6 O 24 (M = Sr, Ba and x = 0.0-1.0) phases has been investigated using General Structure Analysis System (GSAS) programming. The Sr and Ba substituted CZP phases crystallize in the space group R-3 and Z = 6. Powder diffraction data have been subjected to Rietveld refinement to arrive at a satisfactory structural convergence of R-factors. The unit cell volume and polyhedral (ZrO 6 and PO 4 ) distortion increases with rise in the size and mole % of loaded cation in the CZP matrix. The PO 4 stretching and bending vibrations in the Infra red (IR) region have been assigned. SEM, TEM and EDAX analysis provide evidence of Sr and Ba in the matrix. (authors)

Phase transitions in (NH4)2MoO2F4 crystal

Science.gov (United States)

Krylov, Alexander; Laptash, Natalia; Vtyurin, Alexander; Krylova, Svetlana

2016-11-01

The mechanisms of temperature and high pressure phase transitions have been studied by Raman spectroscopy. Room temperature (295 K) experiments under high hydrostatic pressure up to 3.6 GPa for (NH4)2 MoO2 F4 have been carried out. Experimental data indicates a phase transition into a new high-pressure phase for (NH4)2 MoO2 F4 at 1.2 GPa. This phase transition is related to the ordering anion octahedron groups [MoO2 F4]2- and is not associated with ammonium group. Raman spectra of small non-oriented crystals ranging from 10 to 350 K have been observed. The experiment shows anion groups [MoO2 F4]2- and ammonium in high temperature phase are disordered. The phase transition at T1 = 269.8 K is of the first-order, close to the tricritical point. The first temperature phase transition is related to the ordering anion octahedron groups [MoO2 F4]2-. Second phase transitions T2 = 180 K are associated with the ordering of ammonium. The data presented within this study demonstrate that 2D correlation analysis combined with traditional Raman spectroscopy are powerful tool to study phase transitions in the crystals.

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 1

Energy Technology Data Exchange (ETDEWEB)

DOE; ORNL; NREL; EMA; MECA

1999-08-15

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim data report summarizes results as of August, 1999, on the status of the test programs being conducted on three technologies: lean-NO{sub x} catalysts, diesel particulate filters and diesel oxidation catalysts.

Phenotypic Characteristics of PD-1 and CTLA-4 Expression in Symptomatic Acute Hepatitis A.

Science.gov (United States)

Cho, Hyosun; Kang, Hyojeung; Kim, Chang Wook; Kim, Hee Yeon; Jang, Jeong Won; Yoon, Seung Kew; Lee, Chang Don

2016-03-01

The immunoregulatory molecules programmed death 1 (PD-1) and cytotoxic T lymphocyte-associated antigen 4 (CTLA-4) are associated with the dysfunction of antiviral effector T-cells, which leads to T-cell exhaustion and persistent viral infection in patients with chronic hepatitis C and chronic hepatitis B. Little is known about the role of PD-1 and CTLA-4 in patients with symptomatic acute hepatitis A (AHA). Peripheral blood mononuclear cells were isolated from seven patients with AHA and from six patients with nonviral acute toxic hepatitis (ATH) during the symptomatic and convalescent phases of the respective diseases; five healthy subjects acted as controls. The expression of PD-1 and CTLA-4 on T-cells was measured by flow cytometry. PD-1 and CTLA-4 expression during the symptomatic phase was significantly higher in the T-cells of AHA patients than in those of ATH patients or healthy controls (PD-1 18.3% vs 3.7% vs 1.6%, respectively, p<0.05; CTLA-4 23.5% vs 6.1% vs 5.9%, respectively, p<0.05). The levels of both molecules decreased dramatically during the convalescent phase of AHA, whereas a similar pattern was not seen in ATH. Our findings are consistent with a viral-protective effect of PD-1 and CTLA-4 as inhibitory molecules that suppress cytotoxic T-cells and thereby prevent the destruction of virus-infected hepatocytes in AHA.

Process Evaluation of the Tier 1 Program (Secondary 1 Curriculum of the Project P.A.T.H.S.: Findings Based on the Full Implementation Phase

Directory of Open Access Journals (Sweden)

Daniel T. L. Shek

2008-01-01

Full Text Available To understand the implementation quality of the Tier 1 Program (Secondary 1 Curriculum of the Project P.A.T.H.S. (Positive Adolescent Training through Holistic Social Programmes, observers carried out process evaluation in the form of systematic observations of 22 units in 14 randomly selected schools. Results showed that the overall level of program adherence was generally high (range: 45–100%, with an average of 86.3%. High implementation quality of the program in the areas of student interest, student participation and involvement, classroom control, use of interactive delivery method, use of strategies to enhance student motivation, use of positive and supportive feedbacks, instructors’ familiarity with the students, degree of achievement of the objectives, time management, lesson preparation, overall implementation quality, and success of implementation was also found. The present findings are consistent with those observations based on the experimental implementation phase, suggesting that the implementation quality of the Tier 1 Program (Secondary 1 Curriculum was generally high.

NASA SBIR abstracts of 1990 phase 1 projects

Science.gov (United States)

Schwenk, F. C.; Gilman, J. A.; Paige, J. B.

1991-01-01

The research objectives of the 280 projects placed under contract in the National Aeronautics and Space Administration (NASA) 1990 Small Business Innovation Research (SBIR) Phase 1 program are described. The basic document consists of edited, non-proprietary abstracts of the winning proposals submitted by small businesses in response to NASA's 1990 SBIR Phase 1 Program Solicitation. The abstracts are presented under the 15 technical topics within which Phase 1 proposals were solicited. Each project was assigned a sequential identifying number from 001 to 280, in order of its appearance in the body of the report. The document also includes Appendixes to provide additional information about the SBIR program and permit cross-reference in the 1990 Phase 1 projects by company name, location by state, principal investigator, NASA field center responsible for management of each project, and NASA contract number.

COMMIX-1AR/P: A three-dimensional transient single-phase computer program for thermal hydraulic analysis of single and multicomponent systems

International Nuclear Information System (INIS)

Garner, P.L.; Blomquist, R.N.; Gelbard, E.M.

1992-09-01

The COMMIX-1AR/P computer program is designed for analyzing the steady-state and transient aspects of single-phase fluid flow and heat transfer in three spatial dimensions. This version is an extension of the modeling in COMMIX-1A to include multiple fluids in physically separate regions of the computational domain, modeling descriptions for pumps, radiation heat transfer between surfaces of the solids which are embedded in or surround the fluid, a k-var-epsilon model for fluid turbulence, and improved numerical techniques. The porous-medium formulation in COMMIX allows the program to be applied to a wide range of problems involving both simple and complex geometrical arrangements. The input preparation and execution procedures are presented for the COMMIX-1AR/P program and several postprocessor programs which produce graphical displays of the calculated results

COMMIX-1AR/P: A three-dimensional transient single-phase computer program for thermal hydraulic analysis of single and multicomponent systems

Energy Technology Data Exchange (ETDEWEB)

Garner, P.L.; Blomquist, R.N.; Gelbard, E.M.

1992-09-01

The COMMIX-1AR/P computer program is designed for analyzing the steady-state and transient aspects of single-phase fluid flow and heat transfer in three spatial dimensions. This version is an extension of the modeling in COMMIX-1A to include multiple fluids in physically separate regions of the computational domain, modeling descriptions for pumps, radiation heat transfer between surfaces of the solids which are embedded in or surround the fluid, a k-[var epsilon] model for fluid turbulence, and improved numerical techniques. The porous-medium formulation in COMMIX allows the program to be applied to a wide range of problems involving both simple and complex geometrical arrangements. The input preparation and execution procedures are presented for the COMMIX-1AR/P program and several postprocessor programs which produce graphical displays of the calculated results.

Installation Restoration Program. Phase 2. Confirmation/Quantification. Stage 1. Air Force Plant 4, Fort Worth, Texas. Volume 3. Appendix A-1 (Continued).

Science.gov (United States)

1987-12-01

GAO 0 2L -4e- - Lq*Lio rol -4 1 IOU CI S W a G-v a. IV0 0 J= C. Ic LG 4sa C...8217 ’ ~ -i CIj -43j ~LU . l co r I_- z3 335 0- C= cu w- CDP aIC. *I lr_ - CkIJ LA-. n= C G C=> gao ’ GeL) =31 CAEl = C- C-10. LLaJ 1= w CL -* I t CI or SLLJ...6- Z u - a a qcrLLJ < nC Liu~ LI i LL.J CL. w <r LL <r 03 440 -x C= cn z4 -. - XM Z~ A ~ ’’ ~ "~’ , 4 *.\\~.S~4’N’~~’ - Iz JINI 1 *~ I- LLW W, a,

Magnetic phase transition in MnFeP0.5As0.4Si0.1

International Nuclear Information System (INIS)

Wang, J L; Campbell, S J; Tegus, O; Brueck, E; Dou, S X

2010-01-01

We have carried out a detailed investigation of the magnetic phase transition in MnFeP 0.5 As 0.4 Si 0.1 . Temperature hysteresis has been observed in the variable temperature magnetization curves (B appl = 0.01 T) with T C W ∼ 302 K on warming and T C C ∼ 292 K on cooling. The first order nature of this transition in MnFeP 0.5 As 0.4 Si 0.1 is confirmed by the negative slope obtained from isotherms of M 2 versus B/M around the critical temperature. Linear thermal expansion measurements reveal a large volume change, ΔV/V∼8.7x10 -3 at the magnetic phase transition and that this magnetovolume effect is suppressed to ΔV/V ∼ 5.5x10 -3 in an applied field of B appl = 1.0 T. Analyses of 57 Fe Moessbauer spectra (4.5 - 300 K) using a random distribution model and taking nearest-neighbour environments into account, indicate that the paramagnetic and ferromagnetic phases coexist over a temperature range of ∼ 45 K around the Curie temperature. The Debye temperature for MnFeP 0.5 As 0.4 Si 0.1 has been evaluated as θ D = 350 ± 20 K from the temperature dependence of the average isomer shift.

Engineering Phase 2 and Phase 3 certification programs -- PUREX deactivation

International Nuclear Information System (INIS)

Walser, R.L.

1994-01-01

This document describes the training programs required to become a Phase 2 and Phase 3 certified engineer at PUREX during deactivation. With the change in mission, the PUREX engineering/certification training program is being revamped as discussed below. The revised program will be administered by PUREX Technical Training using existing courses and training materials. The program will comply with the requirements of the Department of Energy (DOE) order 5480.20A, ''Personnel Selection, Qualification, Training, and Staffing Requirements at DOE Reactor and Non-Reactor Nuclear Facilities.''

Engineering Phase 2 and Phase 3 certification programs -- PUREX deactivation

Energy Technology Data Exchange (ETDEWEB)

Walser, R.L.

1994-12-13

This document describes the training programs required to become a Phase 2 and Phase 3 certified engineer at PUREX during deactivation. With the change in mission, the PUREX engineering/certification training program is being revamped as discussed below. The revised program will be administered by PUREX Technical Training using existing courses and training materials. The program will comply with the requirements of the Department of Energy (DOE) order 5480.20A, ``Personnel Selection, Qualification, Training, and Staffing Requirements at DOE Reactor and Non-Reactor Nuclear Facilities.``

A monte carlo program for X-rays detection up to 1.4 MeV

International Nuclear Information System (INIS)

Manfredotti, C.; Nastasi, U.

1983-01-01

A monte carlo program has been developed to simulate X-ray spectral response in semiconductor detectors. Photons in the range from 5 KeV to 1.4 MeV are considered as emitted from a source of zero thickness aligned to the crystal axis and followed untill their complete energy loss or their escape from the crystal. The program allows the optimization of important parameters in a semiconductor detector, the study of influence on the spectra obtained and the determination of the energy behavior of efficiency and energy resolution. Some obtained results have been compared with experimental data

The Alert Program for Self-Management of Behaviour in Second Level Schools: Results of Phase 1 of a Pilot Study

Science.gov (United States)

Mac Cobb, Siobhan; Fitzgerald, Brian; Lanigan-O'Keeffe, Carolyn

2014-01-01

This article reports on Phase 1 of a pilot programme on self-management of behaviour with challenging class groups of students as part of the evidence-informed practice of the National Behaviour Support Service. The Alert Program is a structured active learning programme using an engine analogy. The person's engine runs on high, low or just right…

Tank waste remediation system retrieval and disposal mission phase 1 financial analysis

International Nuclear Information System (INIS)

Wells, M.W.

1998-01-01

The purpose of the Tank Waste Remediation System (TWRS) Retrieval and Disposal Mission Phase 1 Financial Analysis is to provide a quantitative and qualitative cost and schedule risk analysis of HNF-1946, Tank Waste Remediation System Retrieval and Disposal Mission Initial Updated Baseline (Swita et al. 1998). The Updated Baseline (Section 3.0) is compared to the current TWRS Project Multi-Year Work Plan (MYWP) for fiscal year (FY) 1998 and target budgets for FY 1999 through FY 2011 (Section 4.1). The analysis then evaluates the executability of HNF-1946 (Sections 4.2 through 4.5) and recommends a path forward for risk mitigation (Sections 4.6, 4.7, and 5.0). A sound systems engineering approach was applied to understand and analyze the Phase 1B Retrieval and Disposal mission. Program and Level 1 Logics were decomposed to Level 8 of the Work Breakdown Structure (WBS) where logic was detailed, scope was defined, detail durations and estimates prepared, and resource loaded schedules developed. Technical Basis Review (TBR) packages were prepared which include this information and, in addition, defined the enabling assumptions for each task, and the risks associated with performance. This process is discussed in Section 2.1. Detailed reviews at the subactivity within the Level 1 Logic TBR levels were conducted to provide the recommended solution to the Phase 1B Retrieval and Disposal Mission. Independent cost analysis and risk assessments were performed by members of the Lockheed Martin Hanford Corporation (LMHC) Business Management and Chief Financial Officer organization along with specialists in risk analysis from TRW, Inc. and Lockheed Martin Energy Systems. The process evaluated technical, schedule, and cost risk by category (program specific fixed and variable, integrated program, and programmatic) based on risk certainly from high probability well defined to very low probability that is not bounded or priceable as discussed in Section 2.2. The results have been

A Switchable Molecular Dielectric with Two Sequential Reversible Phase Transitions: [(CH3)4P]4[Mn(SCN)6].

Science.gov (United States)

Li, Qiang; Shi, Ping-Ping; Ye, Qiong; Wang, Hui-Ting; Wu, De-Hong; Ye, Heng-Yun; Fu, Da-Wei; Zhang, Yi

2015-11-16

A new organic-inorganic hybrid switchable and tunable dielectric compound, [(CH3)4P]4[Mn(SCN)6] (1), exhibits three distinct dielectric states above room temperature and undergoes two reversible solid-state phase transitions, including a structural phase transition at 330 K and a ferroelastic phase transition with the Aizu notation of mmmF2/m at 352 K. The variable-temperature structural analyses disclose that the origin of the phase transitions and dielectric anomalies can be ascribed to the reorientation or motion of both the [(CH3)4P](+) cations and [Mn(SCN)6](4-) anions in solid-state crystals.

Solubility and phase separation of 4-morpholinepropanesulfonic acid (MOPS), and 3-morpholino-2-hydroxypropanesulfonic acid (MOPSO) in aqueous 1,4-dioxane and ethanol solutions

International Nuclear Information System (INIS)

Taha, Mohamed; Lee, Ming-Jer

2011-01-01

Highlights: → Solubilities of MOPS and MOPSO buffers in aqueous 1,4-dioxane and ethanol solutions. → We found that MOPS-induced phase separation of aqueous solution of 1,4-dioxane. → The phase diagram of (MOPS + water + 1,4-dioxane) system at 298.15 K is documented. → The tie-lines within the two-liquid phase region were also determined at 298.15 K. → The effective excluded volume theory was applied to correlate the binodal LLE data. - Abstract: The buffers 4-morpholinepropanesulfonic acid (MOPS) and 3-morpholino-2-hydroxypropanesulfonic acid (MOPSO) are useful biological zwitterionic buffers within the pH range of 6.5 to 7.9 and 6.2 to 7.6, respectively. The solubilities of these buffers were determined in binary mixtures (1,4-dioxane + water) and (ethanol + water) at T = 298.15 K by using the results of density measurements. It has been observed that MOPS induced liquid-liquid phase splitting for the mixtures of 40% to 90% (w/w) 1,4-dioxane in water. The two-liquid phase formation was visualized with disperse orange 25. The phase equilibrium boundaries, including the regions of one liquid, two liquids, (one liquid + one solid) and (two liquids + one solid), for the (MOPS + water + 1,4-dioxane) system have been determined experimentally at T = 298.15 K. The tie lines of the (liquid + liquid) equilibrium were also measured. The Othmer-Tobias and Bancroft equation were used to evaluate the reliability of the tie-line data. The binodal curve was fitted to an empirical equation and the effective excluded volume (EEV) model. The apparent free energies of transfer (ΔG tr ' ) of MOPS and MOPSO from water to 1,4-dioxane and ethanol solutions have been calculated from the solubility data. These ΔG tr ' values were compared with those of some related biological buffers (TRIS, TAPS, TAPSO, and TABS). Furthermore, we also calculated the contribution of transfer free energies (Δg tr ' ) of -OH group from water to 1,4-dioxane and ethanol solutions.

The Portals 4.1 Network Programming Interface

Energy Technology Data Exchange (ETDEWEB)

Barrett, Brian; Brightwell, Ronald B.; Grant, Ryan; Hemmert, Karl Scott; Pedretti, Kevin; Wheeler, Kyle; Underwood, Keith D; Riesen, Rolf; Maccabe, Arthur B.; Hudson, Trammel

2017-04-01

This report presents a specification for the Portals 4 networ k programming interface. Portals 4 is intended to allow scalable, high-performance network communication betwee n nodes of a parallel computing system. Portals 4 is well suited to massively parallel processing and embedded syste ms. Portals 4 represents an adaption of the data movement layer developed for massively parallel processing platfor ms, such as the 4500-node Intel TeraFLOPS machine. Sandia's Cplant cluster project motivated the development of Version 3.0, which was later extended to Version 3.3 as part of the Cray Red Storm machine and XT line. Version 4 is tar geted to the next generation of machines employing advanced network interface architectures that support enh anced offload capabilities.

Construction of 1,3,4-Oxadiazole and 1,3,4-Thiadiazole Library with a High Level of Skeletal Diversity Based on Branching Diversity-Oriented Synthesis on Solid-Phase Supports.

Science.gov (United States)

Ha, Ji-Eun; Yang, Seung-Ju; Gong, Young-Dae

2018-02-12

An efficient solid-phase synthetic route for the construction of 1,3,4-oxadiazole and 1,3,4-thiadiazole libraries based on branching diversity-oriented synthesis (DOS) has been developed in this study. The core skeleton resins, 1,3,4-oxadiazole and 1,3,4-thiadiazole, were obtained through desulfurative and dehydrative cyclizations of thiosemicarbazide resin, respectively. Various functional groups have been introduced to the core skeleton resins, such as aryl, amine, amide, urea, thiourea, and an amino acid. Most of the libraries were purified by simple trituration without extraction or column chromatography after cleavage of the products from the solid-supported resin. As a result, we obtained high yields of pure 1,3,4-oxadiazole and 1,3,4-thiadiazole derivatives (total numbers = 128). Finally, we confirmed the drug-like properties of our library by calculation of physicochemical properties, displays of the skeletal diversities of the library in 3D-space, and occupation of a broad range of areas by their functional groups.

Dynamic Isotope Power System: technology verification phase, program plan, 1 October 1978

International Nuclear Information System (INIS)

1979-01-01

The technology verification phase program plan of the Dynamic Isotope Power System (DIPS) project is presented. DIPS is a project to develop a 0.5 to 2.0 kW power system for spacecraft using an isotope heat source and a closed-cycle Rankine power-system with an organic working fluid. The technology verification phase's purposes are to increase the system efficiency to over 18%, to demonstrate system reliability, and to provide an estimate for flight test scheduling. Progress toward these goals is reported

Lattice parameter values and phase transitions for the Cu2Cd1-zMnzSnSe4 and Cu2Cd1-zFezSnSe4 alloys

International Nuclear Information System (INIS)

Moreno, E.; Quintero, M.; Morocoima, M.; Quintero, E.; Grima, P.; Tovar, R.; Bocaranda, P.; Delgado, G.E.; Contreras, J.E.; Mora, A.E.; Briceno, J.M.; Avila Godoy, R.; Fernandez, J.L.; Henao, J.A.; Macias, M.A.

2009-01-01

X-ray powder diffraction measurements and differential thermal analysis (DTA) were made on polycrystalline samples of the Cu 2 Cd 1-z Mn z SnSe 4 and Cu 2 Cd 1-z Fe z SnSe 4 alloy systems. The diffraction patterns were used to show the equilibrium conditions and to derive lattice parameter values. For Cu 2 Cd 0.8 Fe 0.2 SnSe 4 as well as for Cu 2 Cd 0.2 Fe 0.8 SnSe 4 the crystal structures were refined using the Rietveld method. It was found that the internal distortion parameter σ decreases as Cd is replaced by either Mn and/or Fe. For the Cu 2 Cd 1-z Mn z SnSe 4 and Cu 2 Cd 1-z Fe z SnSe 4 alloy systems, only two single solid phase fields, the tetragonal stannite α(I4-bar2m) and the wurtz-stannite δ (Pmn2 1 ) structures were found to occur in the diagram. In addition to the tetragonal stannite α phase extra X-ray diffraction lines due to MnSe and/or FeSe 2 were observed for as grown samples in the range 0.7 < z < 1.0. However, it was found that the amount of the extra phase decreased for the compressed samples.

Microstructure, crystal structure and electrical properties of Cu{sub 0.1}Ni{sub 0.8}Co{sub 0.2}Mn{sub 1.9}O{sub 4} ceramics obtained at different sintering conditions

Energy Technology Data Exchange (ETDEWEB)

Bodak, O.; Akselrud, L.; Demchenko, P.; Kotur, B.; Mrooz, O.; Hadzaman, I.; Shpotyuk, O.; Aldinger, F.; Seifert, H.; Volkov, S.; Pekhnyo, V

2002-12-16

Details of the formation of Cu{sub 0.1}Ni{sub 0.8}Co{sub 0.2}Mn{sub 1.9}O{sub 4} ceramics under different sintering conditions have been studied by optical microscopy, scanning electron microscopy (SEM), electron probe and energy dispersive spectroscopy (EDX) microanalyses, X-ray diffraction (XRD) and electrical resistivity measurements. Microstructure studies of samples sintered at 1170 deg. C for 1 h indicated the presence of a secondary phase besides the main spinel phase with modified composition. XRD measurements showed that the spinel phase exhibits a tetragonally distorted spinel structure (space group I4{sub 1}/amd, a=5.9410(5) A, c=8.4196(15) A). The secondary phase (solid solution based on NiO) crystallizes with the NaCl-type structure (space group Fm3-bar m, a=4.1872(3) A). The content of the secondary phase in ceramics is 10.61 mass%. For NiMn{sub 2}O{sub 4} ceramics, prepared under the same sintering conditions, the decomposition with Ni{sub 1-x}Mn{sub x}O solid solution (NaCl-type structure) and spinel phase formation have been observed. The tetragonal modification of the spinel phase for NiMn{sub 2}O{sub 4} ceramics is more preferable (space group I4{sub 1}/amd, a=5.9764(5) A, c=8.4201(8) A). The distribution of atoms in the structure has been proposed for both ceramics. According to XRD results the Cu{sub 0.1}Ni{sub 0.8}Co{sub 0.2}Mn{sub 1.9}O{sub 4} ceramic samples, sintered at 920 deg. C for 8 h (program 1), at 920 deg. C for 8 h and at 750 deg. C for 24 h (program 2), at 920 deg. C for 8 h, at 1200 deg. C for 1 h and at 920 deg. C for 24 h (program 3) and at 920 deg. C for 8 h, at 1200 deg. C for 1 h, at 920 deg. C for 24 h and at 750 deg. C for 48 h (program 4), contain a single phase with the cubic spinel structure (space group Fd3-bar m). Small residuals of the secondary phase for the ceramics, prepared via programs 3 and 4, have been observed by SEM investigations. The structure transformations of the spinel phase for Cu{sub 0.1}Ni{sub 0.8}Co

Ammonium dynamics in the disordered α-phase of K1-x(NH4)xY (Y = Cl, Br, I). A neutron scattering study

International Nuclear Information System (INIS)

Natkaniec, I.; Smirnov, L.S.; Shuvalov, L.A.

2002-01-01

The effect of temperature and concentration on the lattice parameters and amplitude-weighted phonon density of states in mixed salts of ammonium-potassium halides is investigated by neutron powder diffraction and incoherent inelastic neutron scattering. In the disordered α-phase (NaCl type) ammonium ions exhibit a fast stochastic reorientation at phonon frequency rates down to ca. 80 K. At 10 K, the incoherent inelastic neutron scattering spectra display four distinct ammonium excitations: two (resonant) modes below and two (localized) above the Debye cut-off energy of potassium halides. High-frequency localized modes correspond to translational and librational vibrations of NH 4 ions. These modes are typical for the ordered phases of ammonium halides. The effect of ammonium concentration on localized and resonant modes is studied for the K 1-x (NH 4 ) x I mixed salts. The harmonic excitations of ammonium in a hypothetical low-temperature α-phase of NH 4 I are approximated to ca. 30, 95, 155 and 250 cm -1 . In a real low-temperature ordered γ-phase of NH 4 I, translational ammonium vibrations are observed at ca. 140-160 cm -1 and librational vibrations at ca.300 cm -1

A comparative study of the Aurivillius phase ferroelectrics CaBi 4Ti 4O 15 and BaBi 4Ti 4O 15

Science.gov (United States)

Tellier, J.; Boullay, Ph.; Manier, M.; Mercurio, D.

2004-06-01

The room temperature structures of the four-layer Aurivillius phase ferroelectrics CaBi 4Ti 4O 15 and BaBi 4Ti 4O 15 are determined by means of single crystal X-ray diffraction. Regarding the CaBi 4Ti 4O 15 phase, in agreement with the tolerance factor, a significant deformation of the perovskite blocks is observed. The rotation system of the octahedra is typical from even layer Aurivillius phases and leads to the use of the space group A2 1am. For the BaBi 4Ti 4O 15 phase, only a weak variation with respect to the F2 mm space group can be suggested from single crystal X-ray diffraction. A significant presence of Ba atoms in the [ M2O 2] slabs is confirmed in agreement with the previous works but specific Ba 2+ and Bi 3+ sites have to be considered due to the large difference in bounding requirement of these cations. Possible origins for the ferroelectric relaxor behavior of the Ba-based compound are discussed in view of the presented structural analyses.

SRNL Phase 1 Assessment Of The WAC/DQO And Unit Operations For The WTP Waste Qualification Program

International Nuclear Information System (INIS)

Peeler, D.; Adamson, D.; Bannochie, C.; Cozzi, A.; Eibling, R.; Hay, M.; Hansen, E.; Herman, D.; Martino, C.; Nash, C.; Pennebaker, F.; Poirier, M.; Reboul, S.; Stone, M.; Taylor-Pashow, K.; White, T.; Wilmarth, B.

2012-01-01

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is currently transitioning its emphasis from a design and construction phase toward start-up and commissioning. With this transition, the WTP Project has initiated more detailed assessments of the requirements related to actual processing of the Hanford Site tank waste. One particular area of interest is the waste qualification program to be implemented to support the WTP. Given the successful implementation of similar waste qualification efforts at the Savannah River Site (SRS), based on critical technical support and guidance from the Savannah River National Laboratory (SRNL), WTP requested the utilization of subject matter experts from SRNL to support a technology exchange to perform a review of the WTP waste qualification program, discuss the general qualification approach at SRS, and to identify critical lessons learned through the support of DWPF's sludge batch qualification efforts. As part of Phase 1, SRNL subject matter experts in critical technical and/or process areas reviewed specific WTP waste qualification information. The Phase 1 review was a collaborative, interactive, and iterative process between the two organizations. WTP provided specific analytical procedures, descriptions of equipment, and general documentation as baseline review material. SRNL subject matter experts reviewed the information and, as appropriate, requested follow-up information or clarification to specific areas of interest. This process resulted in multiple teleconferences with key technical contacts from both organizations resolving technical issues that lead to the results presented in this report. This report provides the results of SRNL's Phase 1 review of the WAC-DQO waste acceptance criteria and processability parameters, and the specific unit operations which are required to support WTP waste qualification efforts. The review resulted in SRNL providing concurrence, alternative methods, or gap identification

SRNL PHASE 1 ASSESSMENT OF THE WAC/DQO AND UNIT OPERATIONS FOR THE WTP WASTE QUALIFICATION PROGRAM

Energy Technology Data Exchange (ETDEWEB)

Peeler, D.; Adamson, D.; Bannochie, C.; Cozzi, A.; Eibling, R.; Hay, M.; Hansen, E.; Herman, D.; Martino, C.; Nash, C.; Pennebaker, F.; Poirier, M.; Reboul, S.; Stone, M.; Taylor-Pashow, K.; White, T.; Wilmarth, B.

2012-05-16

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is currently transitioning its emphasis from a design and construction phase toward start-up and commissioning. With this transition, the WTP Project has initiated more detailed assessments of the requirements related to actual processing of the Hanford Site tank waste. One particular area of interest is the waste qualification program to be implemented to support the WTP. Given the successful implementation of similar waste qualification efforts at the Savannah River Site (SRS), based on critical technical support and guidance from the Savannah River National Laboratory (SRNL), WTP requested the utilization of subject matter experts from SRNL to support a technology exchange to perform a review of the WTP waste qualification program, discuss the general qualification approach at SRS, and to identify critical lessons learned through the support of DWPF's sludge batch qualification efforts. As part of Phase 1, SRNL subject matter experts in critical technical and/or process areas reviewed specific WTP waste qualification information. The Phase 1 review was a collaborative, interactive, and iterative process between the two organizations. WTP provided specific analytical procedures, descriptions of equipment, and general documentation as baseline review material. SRNL subject matter experts reviewed the information and, as appropriate, requested follow-up information or clarification to specific areas of interest. This process resulted in multiple teleconferences with key technical contacts from both organizations resolving technical issues that lead to the results presented in this report. This report provides the results of SRNL's Phase 1 review of the WAC-DQO waste acceptance criteria and processability parameters, and the specific unit operations which are required to support WTP waste qualification efforts. The review resulted in SRNL providing concurrence, alternative methods, or gap

Phase 1 report: the 4D seismic market from 2000 to 2003

International Nuclear Information System (INIS)

Sagary, C.

2004-01-01

This report synthesizes the phase 1 results of the joint industrial project, called ''4D Seismic: Technologies, Economics and Issues''. This project was conducted by IFP between November 2003 and April 2004, in collaboration with Compagnie Generale de Geophysique (CGG) and sponsored by Gaz de France and 4. Wave Imaging. Phase 1 offers an objective view of the 4D seismic market over the period 2000-2003. The market has been assessed from IFP extensive databases, gathering 115 4D projects conducted worldwide and from interviews of seven oil companies, both representing 90% of the activity in time-lapse seismic. This study provides sales estimation and sales/projects breakdown by: in-house/subcontracted activity, geography, onshore/offshore, reservoir rocks and recovery methods, technology/methodology, oil companies and service companies. The market of 4D seismic has been split into 4 segments: acquisition, processing, reservoir studies - feasibility, interpretation and seismic history matching -, borehole seismic (acquisition and processing). In addition, the market of passive seismic monitoring, another technique of seismic reservoir monitoring has also been estimated. The main sources, used to build the IFP databases, were: Worldwide Global E and P Service Reports from IHS Energy, World Geophysical News, an extensive bibliographic study through more than 200 articles, abstracts and summaries, a collaboration with CGG. For all market estimations, numbers computed from IFP databases and from interviews of oil companies were extrapolated from 90% to 100%, to quantify the total 4D activity. The estimations obtained were not rounded in order to preserve trends with a consistent computation from one year to another and from one market segment to another, despite uncertainties of about 10%. Quality controls were performed to validate the final estimations: volumes of 4D seismic data, computed from IFP databases, were checked by comparing processed data with acquired data

A new set of K3Fe3(PO4)4·yH2O (0 ≤ y ≤ 1) layered phases obtained by topotactic reactions

Science.gov (United States)

Trad, Khiem; Wattiaux, Alain; Ben Amara, Mongi; Delmas, Claude; Carlier, Dany

2018-06-01

K3Fe3(PO4)4·H2O powder was synthesized by Na+/K+ exchange reaction from Na3Fe3(PO4)4 in aqueous medium. The replacement of the sodium cations by the potassium larger ones and water molecules causes a structural distortion leading to P2/n monoclinic K3Fe3(PO4)4·H2O. This new layered phase was characterized by XRD, Mössbauer spectroscopy and magnetic measurements. The study of its thermal stability reveals that other new layered K3Fe3(PO4)4·yH2O with (0 ≤ y ≤ 1) phases can be stabilized up to 600 °C and finally at higher temperature a new K3Fe3(PO4)4 polymorph with a different structural type is irreversibility formed.

Preliminary analysis of a 1:4 scale prestressed concrete containment vessel model

International Nuclear Information System (INIS)

Dameron, R.A.; Rashid, Y.R.; Luk, V.K.; Hessheimer, M.F.

1997-01-01

Sandia National Laboratories is conducting a research program to investigate the integrity of nuclear containment structures. As part of the program Sandia will construct an instrumented 1:4 scale model of a prestressed concrete containment vessel (PCCV) for pressurized water reactors (PWR), which will be pressure tested up to its ultimate capacity. One of the key program objectives is to develop validated methods to predict the structural performance of containment vessels when subjected to beyond design basis loadings. Analytical prediction of structural performance requires a stepwise, systematic approach that addresses all potential failure modes. The analysis effort includes two and three-dimensional nonlinear finite element analyses of the PCCV test model to evaluate its structural performance under very high internal pressurization. Such analyses have been performed using the nonlinear concrete constitutive model, ANACAP-U, in conjunction with the ABAQUS general purpose finite element code. The analysis effort is carried out in three phases: preliminary analysis; pretest prediction; and post-test data interpretation and analysis evaluation. The preliminary analysis phase serves to provide instrumentation support and identify candidate failure modes. The associated tasks include the preliminary prediction of failure pressure and probable failure locations and the development of models to be used in the detailed failure analyses. This paper describes the modeling approaches and some of the results obtained in the first phase of the analysis effort

FORTRAN program for calculating liquid-phase and gas-phase thermal diffusion column coefficients

International Nuclear Information System (INIS)

Rutherford, W.M.

1980-01-01

A computer program (COLCO) was developed for calculating thermal diffusion column coefficients from theory. The program, which is written in FORTRAN IV, can be used for both liquid-phase and gas-phase thermal diffusion columns. Column coefficients for the gas phase can be based on gas properties calculated from kinetic theory using tables of omega integrals or on tables of compiled physical properties as functions of temperature. Column coefficients for the liquid phase can be based on compiled physical property tables. Program listings, test data, sample output, and users manual are supplied for appendices

NASA Research Announcement Phase 1 Report and Phase 2 Proposal for the Development of a Power Assisted Space Suit Glove Assembly

Science.gov (United States)

Cadogan, Dave; Lingo, Bob

1996-01-01

In July of 1996, ILC Dover was awarded Phase 1 of a contract for NASA to develop a prototype Power Assisted Space Suit glove to enhance the performance of astronauts during Extra-Vehicular Activity (EVA). This report summarizes the work performed to date on Phase 1, and details the work to be conducted on Phase 2 of the program. Phase 1 of the program consisted of research and review of related technical sources, concept brainstorming, baseline design development, modeling and analysis, component mock-up testing, and test data analysis. ILC worked in conjunction with the University of Maryland's Space Systems Laboratory (SSL) to develop the power assisted glove. Phase 2 activities will focus on the design maturation and the manufacture of a working prototype system. The prototype will be tested and evaluated in conjunction with existing space suit glove technology to determine the performance enhancement anticipated with the implementation of the power assisted joint technology in space suit gloves.

Electrodril system field test program. Phase II: Task C-1-deep drilling system demonstration. Final report for Phase II: Task C-1

Energy Technology Data Exchange (ETDEWEB)

Taylor, P D

1981-04-01

The Electrodril Deep Drilling System field test demonstrations were aborted in July 1979, due to connector problems. Subsequent post test analyses concluded that the field replacable connectors were the probable cause of the problems encountered. The designs for both the male and female connectors, together with their manufacturing processes, were subsequently modified, as was the acceptance test procedures. A total of nine male and nine female connectors were manufactured and delivered during the 2nd Quarter 1980. Exhaustive testing was then conducted on each connector as a precursor to formal qualification testing conducted during the month of October 1980, at the Brown Oil Tool test facility located in Houston, Texas. With this report, requirements under Phase II, Task C-1 are satisfied. The report documents the results of the connector qualification test program which was successfully completed October 28, 1980. In general, it was concluded that connector qualification had been achieved and plans are now in progress to resume the field test demonstration program so that Electrodril System performance predictions and economic viability can be evaluated.

CD4(+) type II NKT cells mediate ICOS and programmed death-1-dependent regulation of type 1 diabetes.

Science.gov (United States)

Kadri, Nadir; Korpos, Eva; Gupta, Shashank; Briet, Claire; Löfbom, Linda; Yagita, Hideo; Lehuen, Agnes; Boitard, Christian; Holmberg, Dan; Sorokin, Lydia; Cardell, Susanna L

2012-04-01

Type 1 diabetes (T1D) is a chronic autoimmune disease that results from T cell-mediated destruction of pancreatic β cells. CD1d-restricted NKT lymphocytes have the ability to regulate immunity, including autoimmunity. We previously demonstrated that CD1d-restricted type II NKT cells, which carry diverse TCRs, prevented T1D in the NOD mouse model for the human disease. In this study, we show that CD4(+) 24αβ type II NKT cells, but not CD4/CD8 double-negative NKT cells, were sufficient to downregulate diabetogenic CD4(+) BDC2.5 NOD T cells in adoptive transfer experiments. CD4(+) 24αβ NKT cells exhibited a memory phenotype including high ICOS expression, increased cytokine production, and limited display of NK cell markers, compared with double-negative 24αβ NKT cells. Blocking of ICOS or the programmed death-1/programmed death ligand 1 pathway was shown to abolish the regulation that occurred in the pancreas draining lymph nodes. To our knowledge, these results provide for the first time cellular and molecular information on how type II CD1d-restricted NKT cells regulate T1D.

A photolabile linker for the solid-phase synthesis of 4-substituted NH-1,2,3-triazoles

DEFF Research Database (Denmark)

Qvortrup, Katrine; Nielsen, Thomas Eiland

2011-01-01

A novel photolabile linker for solid-phase synthesis is presented. The linker displays an azido handle for copper-catalyzed azide–alkyne cycloaddition reactions with a variety of alkynes, remains intact under typical solid-phase reaction conditions, and enables a mild photolytic release of 4...

[Environmental investigation of ground water contamination at Wright- Patterson Air Force Base, Ohio]. Volume 4, Health and Safety Plan (HSP); Phase 1, Task 4 Field Investigation report: Draft

Energy Technology Data Exchange (ETDEWEB)

1991-10-01

This Health and Safety Plan (HSP) was developed for the Environmental Investigation of Ground-water Contamination Investigation at Wright-Patterson Air Force Base near Dayton, Ohio, based on the projected scope of work for the Phase 1, Task 4 Field Investigation. The HSP describes hazards that may be encountered during the investigation, assesses the hazards, and indicates what type of personal protective equipment is to be used for each task performed. The HSP also addresses the medical monitoring program, decontamination procedures, air monitoring, training, site control, accident prevention, and emergency response.

Measurements of two-phase flow patterns in a 4 x 4 rod bundle

International Nuclear Information System (INIS)

Akio tomiyama; Akira Sou; Shigeo Hosokawa; Masato Mitsuhashi; Kohei Noda; Yasushi Tsubo; Kaichiro Mishima; Yoshiro Kudo

2005-01-01

Air-water two-phase flow patterns in a 4 x 4 square lattice rod bundle consisting of an acrylic channel box of 68 mm in width and transparent rods of 12 mm in diameter were measured by utilizing FEP (fluorinated ethylene propylene) tubes for the rods. The FEP possesses the same refractive index with water, and therefore, whole flow patterns in the bundle and local flow patterns in subchannels were visualized with little optical distortion. In addition to the visualization, transmission rates of laser beam from one rod to its opponent rod and two-point correlation coefficients of phase indicator functions were measured to examine the feasibility of objective identification of flow patterns in subchannels. The ranges of liquid and gas volume fluxes, JL and JG, were 0.1 < JL < 2.0 m/s and 0.04 < JG < 8.85 m/s, respectively. As a result, the following conclusions were obtained: (1) slug flow pattern does not appear in the rod bundle and bubbly flow would directly transit to churn flow, (2) the measured boundary between bubbly and churn flows is close to the boundary between bubbly and slug flows given by Mishima and Ishii's flow pattern transition model, (3) critical void fraction causing bubbly to churn flow transition depends on a subchannel, i.e., about 0.3 for inner subchannels, about 0.2 for side subchannels and about 0.1 for corner subchannels, and (4) the two-point correlation coefficient of phase indicator functions for two inner subchannels shows a steep increase at the bubbly to churn flow transition, which, in turn, means that the two-point correlation is an appropriate indicator for detecting this transition. (authors)

Research on radionuclide migration under subsurface geochemical conditions. JAERI/AECL Phase II Collaborative Program Year 1 (joint research)

International Nuclear Information System (INIS)

1998-11-01

A radionuclide migration experiment program for fractured rocks was performed under the JAERI/AECL Phase-II Collaborative Program on research and development in radioactive waste management. The program started in the fiscal year 1993, as a five-year program consists of Quarried block radionuclide migration program, Speciation of long-lived radionuclides in groundwater, Isotopic hydrogeology and Groundwater flow model development. During the first year of the program (Program Year 1: March 18, 1994 - September 30, 1994), a plan was developed to take out granite blocks containing part of natural water-bearing fracture from the wall of the experimental gallery at the depth of 240 m, and literature reviews were done in the area of the speciation of long-lived radionuclides in groundwater, isotopic hydrogeology and the groundwater flow model development to proceed further work for the Program Year 2. (author)

Structural Phase Transitions of Mg(BH4)2 under Pressure

International Nuclear Information System (INIS)

George, L.; Drozd, V.; Saxena, S.; Bardaji, E.; Fichtner, M.

2009-01-01

The structural stability of Mg(BH4)2, a promising hydrogen storage material, under pressure has been investigated in a diamond anvil cell up to 22 GPa with combined synchrotron X-ray diffraction and Raman spectroscopy. The analyses show a structural phase transition around 2.5 GPa and again around 14.4 GPa. An ambient-pressure phase of Mg(BH4)2 has a hexagonal structure (space group P61, a = 10.047(3) A, c = 36.34(1) A, and V = 3176(1) A3 at 0.2 GPa), which agrees well with early reports. The structure of high-pressure phase is found to be different from reported theoretical predictions; it also does not match the high-temperature phase. The high-pressure polymorph of Mg(BH4)2 is found to be stable on decompression, similar to the case of the high-temperature phase. Raman spectroscopic study shows a similarity in high-pressure behavior of as-prepared Mg(BH4)2 and its high-temperature phase.

Preparation and properties of 1-tetradecanol/1,3:2,4-di-(3,4-dimethyl) benzylidene sorbitol gelatinous form-stable phase change materials

International Nuclear Information System (INIS)

Tian, Tuo; Song, Jian; Niu, Libo; Feng, Rongxiu

2013-01-01

Graphical abstract: The 1,3:2,4-di-(3,4-dimethyl) benzylidene sorbitol can self-assemble to form three-dimensional network and immobilized the 1-tetradecanol. As a result, the gel-to-sol transition temperature of the composite PCM increased and the 1-tetradecanol leakage decreased. Highlights: ► First used of 1,3:2,4-di-(3,4-dimethyl) benzylidene sorbitol in alcohol-based PCMs. ► A new method of doping with exfoliated graphite is presented. ► A possible mechanism for decreasing leakage has been proposed based on SEM results. ► The prepared composite PCMs showed a high-energy storage density. ► The addition of exfoliated graphite enhanced the thermal conductivity of the PCMs. - Abstract: A 1-tetradecanol (TD)/1,3:2,4-di-(3,4-dimethyl) benzylidene sorbitol (DMDBS) composite was prepared as a novel form-stable phase change material (PCM), and the properties of the composites such as the gel-to-sol transition temperature, the latent heat, the microstructure and the thermal storage performance were characterized. The composite was prepared by impregnating DMDBS into TD and the maximum feasible weight percentage of TD was determined to be 94.2 wt%. The gel-to-sol transition temperature of the composite PCM was 158.3–180.0 °C, which is well above the melting point of 1-tetradecanol. Differential scanning calorimeter (DSC) was used to determine the melting and freezing enthalpies of 1-tetradecanol in the composite PCM and the values are 218.5 and 215.3 J g −1 , respectively. Scanning electron microscopy (SEM) results showed that 1-tetradecanol dispersed in the three-dimensional network formed by DMDBS. The relationship between the amount of DMDBS additive and the leakage was also discussed. The thermal conductivity of the composite PCM was improved by doping with exfoliated graphite

The portals 4.0.1 network programming interface.

Energy Technology Data Exchange (ETDEWEB)

Barrett, Brian W.; Brightwell, Ronald Brian; Pedretti, Kevin; Wheeler, Kyle Bruce; Hemmert, Karl Scott; Riesen, Rolf E.; Underwood, Keith Douglas; Maccabe, Arthur Bernard; Hudson, Trammell B.

2013-04-01

This report presents a specification for the Portals 4.0 network programming interface. Portals 4.0 is intended to allow scalable, high-performance network communication between nodes of a parallel computing system. Portals 4.0 is well suited to massively parallel processing and embedded systems. Portals 4.0 represents an adaption of the data movement layer developed for massively parallel processing platforms, such as the 4500-node Intel TeraFLOPS machine. Sandias Cplant cluster project motivated the development of Version 3.0, which was later extended to Version 3.3 as part of the Cray Red Storm machine and XT line. Version 4.0 is targeted to the next generation of machines employing advanced network interface architectures that support enhanced offload capabilities. 3

Phase diagram of the CsH/sub 2/AsO/sub 4/-CsH /SUB 0. 1/ D /SUB 1. 9/ AsO/sub 4/ System

Energy Technology Data Exchange (ETDEWEB)

Rakhimov, K.; Karapetyan, F.S.; Kozhenkov, V.Y.; Polyakov, Y.A.; Zhigarnovskii, B.M.

1986-05-01

The authors determined the melting point of dueterated cesium hydrogen arsenate of composition CsH /SUB 0.1/ D /SUB 1.9/ AsO/sub 4/ melts. Specimens for investigation of the system were prepared by fusion of appropriate amounts of CsH/sub 2/AsO/sub 4/ and CsH /SUB 0.1/ D /SUB 1.9/ AsO/sub 4/ in sealed quartz ampuls. In addition, the unit-cell parameters of the phases of the specimens practically did not differ from the corresponding parameters of the starting products over the entire range of concentrations.

Estuary 2100 Project, Phase 1: Resilient Watersheds for a Changing Climate

Science.gov (United States)

Information about the SFBWQP Estuary 2100 Project, Phase 1: Resilient Watersheds for a Changing Climate , part of an EPA competitive grant program to improve SF Bay water quality focused on restoring impaired waters and enhancing aquatic resources.

Phase relation of LaFe11· 6Si1· 4 compounds annealed at different ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 35; Issue 2. Phase relation of LaFe11.6Si1.4 compounds annealed at different high-temperature and the magnetic property of LaFe11.6−CoSi1.4 compounds. Xiang Chen Yungui Chen Yongbai Tang. Volume 35 Issue 2 April 2012 pp 175-182 ...

On a phase transition of a Kosterlitz-thouless-type in the d=4, U(1)-lattice gauge theory

International Nuclear Information System (INIS)

Marchetti, D.H.U.; Perez, J.F.

1986-12-01

The d=4, U(1)-lattice gauge theory with the Villain action may be represented as a locally neutral gas of topological (plaquette) charges which interact via a logarithmically confining potential, is shown. Using this representation a renormalization group analysis to show the existence of a phase transition of the Kosterlitz-Thouless-type was performed. An improved hierarchical version of the model which displays (unlike the usual Migdal-Kadanoff approach) a stable line of gaussian fixed points at low temperatures, which should correspond to the usual deconfining region of these systems is presented. (Author) [pt

Structure of (NH4)3H(SeO4)2 in high-temperature phases I and II

International Nuclear Information System (INIS)

Lukaszewicz, K.; Pietraszko, A.; Augustyniak, M.A.

1993-01-01

Triammonium hydrogenbis(tetraoxoselenate), (NH 4 ) 3 H(SeO 4 ) 2 , M r =341.04, Z=3, λ(Mo K anti α)=0.71073 A, F(000)=498. Phase I: trigonal, R anti 3m, a=6.090(1), c=22.759(5) A, V=731.0(2) A 3 , D x =2.32 g cm -3 , μ=68.7 cm -1 , T=355 K, R=0.0336 for 241 unique reflections with I>4σ(I). Phase II: trigonal, R anti 3, a=6.064(1), c=22.904(5) A, V=729.4(2) A 3 , D x =2.33 g cm -3 , μ=68.8 cm -1 , T=310 K, R=0.0374 for 397 unique reflections with I>4σ(I). In both phases, SeO 4 tetrahedra are linked by a dynamic system of symmetrically disordered hydrogen bonds in planes perpendicular to the trigonal axis. In phase II, SeO 4 tetrahedra deviate from the (210) plane owing to a small rotation of about 4 about the trigonal axis. In phase I, owing to symmetry enhancement, both orientations of SeO 4 tetrahedra are equally probable on both sides of (210), which is therefore a mirror plane. (orig.)

Noncyanide Stripper Placement Program. Phase 1

Science.gov (United States)

1989-05-01

nickel are removed from the Electrochemical NICKEL-SOL solution as copper sulfate pentahydrate (CuSO4.5H20) and nickel sulfate (NiSO4.6H20). At any given...ammonium hydroxide (NH4OH) to 75 ml of water and dissolve 1.5 grams of copper sulfate pentahydrate (CuSO4.5H20) in the mixture. Add water to bring to...must be dumped. The copper and nickel dissolved can be recovered in the form of copper sulfate and nickel sulfate respectively. The Electrochemicals

Initial results of strand produced in Phase 2 of the SSCL Vendor Qualification Program

International Nuclear Information System (INIS)

Erdmann, M.; Capone, D. II; Coleman, S.; Jones, B.; Seuntjens, J.

1993-05-01

In 1991, the Superconducting Super Collider Laboratory (SSCL) instituted a program to qualify specific superconductor manufacturers for production of cable acceptable for use in both Collider Dipole (CDM) and Quadrupole (CQM) magnets. The SSCL Vendor Qualification Program (VQP) was designed with two Phases. Phase 1 was divided into two additional phases, 1A and 1B, which ran concurrently. In Phase 1B, each vendor was directed to manufacture roughly 3000 kg of cable using a ''baseline'' process. The baseline process was agreed to by both the SSCL and the vendor at the beginning of the VQP. In this phase, process control was closely monitored with the use of statistical methods and each vendor was graded based on these results. Phase 1A, known as the R ampersand D phase, was developed to allow each vendor an opportunity to optimize and improve on their baseline process in terms of both cost and manufacturability. In this phase, multifilament billets were designed to explore several key variables such as alternate alloy sources, process modifications and improved billet designs. At the end of Phase 1, the results from both 1A and 1B were evaluated at a review between the SSCL and each vendor, and a final Phase 2 process was generated and fixed using the best results. In Phase 2, each vendor is required to manufacture roughly 6000 kg of superconducting cable under a firm fixed price contract which can then be used to create an accurate price estimate for competitive bidding on the full rate production CDM and CQM contracts. At the end of Phase 2, each vendor must meet the minimum requirements outlined in the contract to become a qualified superconducting cable supplier. For one requirement, critical process variables identified by the SSCL Conductor Department at the beginning of the VQP will be evaluated to determine the quality and uniformity of the material produced during Phase 2 of the program

Level 1 probabilistic risk assessment of low power and shutdown operations at a PWR: Phase 2 results

International Nuclear Information System (INIS)

Chu, T.L.; Bozoki, G.; Kohut, P.; Musicki, Z.; Wong, S.M.; Yang, J.; Hsu, C.J.; Diamond, D.J.; Su, R.F.; Holmes, B.; Siu, N.; Bley, D.; Lin, J.

1992-01-01

As a result of the Chernobyl accident and other precursor events (e.g., Diablo Canyon), the US Nuclear Regulatory Commission's (NRC's) Office of Nuclear Regulatory Research (RES) initiated an extensive project during 1989 to carefully examine the potential risks during Low Power and Shutdown (LP ampersand S) operations. Shortly after the program began, an event occurred at the Vogtle plant during shutdown, which further intensified the effort of the LP ampersand S program. In the LP ampersand S program, one pressurized water reactor (PWR), Surry, and one boiling water reactor (BWR), Grand Gulf, were selected, mainly because they were previously analyzed in the NUREG-1150 Study. The Level-1 Program is being performed in two phases. Phase 1 was dedicated to performing a coarse screening level-1 analysis including internal fire and flood. A draft report was completed in November, 1991. In the phase 2 study, mid-loop operations at the Surry plant were analyzed in detail. The objective of this paper is to present the approach of the phase 2 study and the preliminary results and insights

Krakow clean fossil fuels and energy efficiency program. Phase 1 report

Energy Technology Data Exchange (ETDEWEB)

Butcher, T.; Pierce, B. [eds.

1995-06-01

Krakow is one of the largest and oldest cities in Poland. It is situated in the south of the country on the banks of the Vistula River. From the 11th until the 17th centuries, it was the capital of Poland. Today, Krakow is a city of 750,000 residents, one of the largest centers of higher education, an important industrial center, and is of particular importance because of the number and kinds of historic buildings and sites. For this reason, Krakow was included by the UNESCO in the list of the world`s cultural heritages. For about three decades, significant air pollution has been one of Krakow`s most serious problems. Because the city is situated in the Vistula River valley, it is poorly ventilated and experiences a high concentration of air pollutants. The quality of air in Krakow is affected mainly by industry (Sendzimir Steelworks, energy industry, chemical plants), influx from the Silesian industrial region (power plants, metallurgy), transboundary pollution (Ostrava - Czech Republic), and local sources of low pollution, i.e. more than 1,000 boiler houses using solid fuels and more than 100,000 coal-fired home stoves. These local sources, with low stacks and almost no pollution-control equipment, are responsible for about 35-40% of the air pollution. This report presents phase I results of a program to reduce pollution in krakow. Phase I was to gather information on emissions and costs, and to verify assumptions on existing heating methods and alternatives.

Phase stability of superconductive Y1Ba2Cu4O8

International Nuclear Information System (INIS)

Hegde, M.S.; Kumaraswamy, B.V.; Pandey, S.P.; Narlikar, A.V.

1997-01-01

The stability of the 124 superconductive phase YBa 2 Cu 4 O 8 upon exposure to air and saturated humidity at ambient temperature has been studied by thermogravimetry, X-ray diffraction, and ac susceptometry. Extent of phase conversion was monitored by TG and confirmed by XRD and ac susceptometry. 124 samples upon prolonged exposure to air were found to be no longer phase-pure, with partial conversion to 123 and CuO. On oxygen annealing, reconversion of 123 + GuO to 124 was observed. However, upon prolonged exposure to saturated humid conditions, phase-pure 124 dissociated irreversibly into 211, GuO, and a highly disordered 124-like structure with planar defects along many hkl indices and was found to be nonsuperconducting even up to 60 K

Lattice parameter values and phase transitions for the Cu2Cd1-zMn zGeSe4 and Cu2Cd1-zFe zGeSe4 alloys

International Nuclear Information System (INIS)

Quintero, E.; Tovar, R.; Quintero, M.; Delgado, G.E.; Morocoima, M.; Caldera, D.; Ruiz, J.; Mora, A.E.; Briceno, M.; Fernandez, J.L.

2007-01-01

X-ray powder diffraction measurements and differential thermal analysis (DTA) were made on polycrystalline samples of the Cu 2 Cd 1-z Mn z GeSe 4 and Cu 2 Cd 1-z Fe z GeSe 4 alloy systems. The diffraction patterns were used to show the equilibrium conditions and to derive lattice parameter values. The effect of the annealing temperature and cooling rate to room temperature are discussed. For the Cu 2 Cd 1-z Fe z GeSe 4 system, only two single solid phase fields, the tetragonal stannite α and the wurtz-stannite δ structures were found to occur in the diagram. For the Cu 2 Cd 1-z Mn z GeSe 4 system, in addition to the tetragonal stannite α and the wurtz-stannite δ phases, MnSe was found to exist in the diagram. The DTA experiments showed that the cooling curves for both systems exhibited effects of undercooling

Phase relations, crystal structure, and phase transformation of In_1_−_xNb_1_−_xTi_2_xO_4 (0 ≤ x < 0.45) in In_2O_3–Nb_2O_5–TiO_2 system

International Nuclear Information System (INIS)

Su, Liumei; Fan, Xing; Cai, Gemei; Liu, Huashan; Jin, Zhanpeng

2015-01-01

Phase relations, crystal structures, and phase transformation of In_1_−_xNb_1_−_xTi_2_xO_4 (0 ≤ x < 0.45) in In_2O_3–Nb_2O_5–TiO_2 ternary system were investigated for the first time. A number of samples with different compositions were prepared by a solid-state reaction method, and phase assembles were analyzed by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe micro-analysis (EPMA). Five three-phase regions, ten two-phase regions, and six single-phase solid solutions were determined in this system. The solid solution of In_1_−_xNb_1_−_xTi_2_xO_4 (0 ≤ x < 0.45) is composed of both ordered monoclinic wolframite-type structure (0 ≤ x < 0.35) and disordered orthorhombic α-PbO_2 type structure (0.35 < x < 0.45). Driving force for composition-driven phase transformation in In_1_−_xNb_1_−_xTi_2_xO_4 (0 ≤ x < 0.45) stems from the ordering of cations. The ever reported compound InNbTiO_6 with an orthorhombic α-PbO_2 type structure was amended to be a monoclinic wolframite-type structure. Present investigations will be useful for the whole ceramic community working with In_2O_3–Nb_2O_5–TiO_2 ternary system as well as for the development of functional materials. - Highlights: • Phase relations of In_2O_3–Nb_2O_5–TiO_2 ternary system were constructed. • Crystal structures of a novel solid solution In_1_−_xNb_1_−_xTi_2_xO_4 were determined. • Crystal structure of InNbTiO_6 was amended to be a wolframite-type structure. • Composition-driven phase transformation of In_1_−_xNb_1_−_xTi_2_xO_4 was investigated.

Synthesis, crystal structure and magnetic property of a new 1D molecular material [1-(4'-chlorobenzyl)-4-aminopyridinium](+) bis(maleonitriledithiolato)nickel(-)

International Nuclear Information System (INIS)

Ni Chunlin; Dang Dongbin; Li Yizhi; Gao Song; Ni Zhaoping; Tian Zhengfang; Meng Qingjin

2005-01-01

A new ion-pair complex, [1-(4'-chlorobenzyl)-4-aminopyridinium](+)bis(maleonitrile-dithiolato) nickel(-),[ClbzPyNH 2 ][Ni(mnt) 2 ] (1), has been prepared and characterized. X-ray single crystal structure conforms that the Ni(mnt) 2 - anions and [ClbzPyNH 2 ] + cations of 1 form completely segregated uniform stacking columns with the Ni...Ni distance 3.944A in the Ni(mnt) 2 - stacking column. The temperature dependence of the magnetic susceptibility reveals that 1 undergoes a magnetic transition, and exhibits ferromagnetic interaction in the high-temperature phase and spin gap system in the low-temperature phase

Lattice parameters values and phase diagram for the Cu2Zn1-zFezGeSe4 alloy system

International Nuclear Information System (INIS)

Caldera, D.; Quintero, M.; Morocoima, M.; Quintero, E.; Grima, P.; Marchan, N.; Moreno, E.; Bocaranda, P.; Delgado, G.E.; Mora, A.E.; Briceno, J.M.; Fernandez, J.L.

2008-01-01

X-ray powder diffraction and differential thermal analysis (DTA) measurements were made on polycrystalline samples of the Cu 2 Zn 1-z Fe z GeSe 4 alloy system. The diffraction patterns were used to show the equilibrium conditions and to estimate crystalline parameter values. It was found that, at room temperature, a single phase solid solution with the tetragonal stannite α structure (I4-bar2m) occurs across the whole composition range. The DTA thermograms were used to construct the phase diagram of the Cu 2 Zn 1-z Fe z GeSe 4 alloy system. It was confirmed that the Cu 2 ZnGeSe 4 compound melts incongruently. It was observed that undercooling effects occur for samples with z > 0.9

NASA SBIR abstracts of 1991 phase 1 projects

Science.gov (United States)

Schwenk, F. Carl; Gilman, J. A.; Paige, J. B.

1992-01-01

The objectives of 301 projects placed under contract by the Small Business Innovation Research (SBIR) program of the National Aeronautics and Space Administration (NASA) are described. These projects were selected competitively from among proposals submitted to NASA in response to the 1991 SBIR Program Solicitation. The basic document consists of edited, non-proprietary abstracts of the winning proposals submitted by small businesses. The abstracts are presented under the 15 technical topics within which Phase 1 proposals were solicited. Each project was assigned a sequential identifying number from 001 to 301, in order of its appearance in the body of the report. Appendixes to provide additional information about the SBIR program and permit cross-reference of the 1991 Phase 1 projects by company name, location by state, principal investigator, NASA Field Center responsible for management of each project, and NASA contract number are included.

NASA SBIR abstracts of 1992, phase 1 projects

Science.gov (United States)

Schwenk, F. C.; Gilman, J. A.; Paige, J. B.; Sacknoff, S. M.

1993-01-01

The objectives of 346 projects placed under contract by the Small Business Innovation Research (SBIR) program of the National Aeronautics and Space Administration (NASA) are described. These projects were selected competitively from among proposals submitted to NASA in response to the 1992 SBIR Program Solicitation. The basic document consists of edited, non-proprietary abstracts of the winning proposals submitted by small businesses. The abstracts are presented under the 15 technical topics within which Phase 1 proposals were solicited. Each project was assigned a sequential identifying number from 001 to 346, in order of its appearance in the body of the report. Appendixes to provide additional information about the SBIR program and permit cross-reference of the 1992 Phase 1 projects by company name, location by state, principal investigator, NASA Field Center responsible for management of each project, and NASA contract number are included.

COMMIX-1AR/P: A three-dimensional transient single-phase computer program for thermal hydraulic analysis of single and multicomponent systems. Volume 2, User`s guide

Energy Technology Data Exchange (ETDEWEB)

Garner, P.L.; Blomquist, R.N.; Gelbard, E.M.

1992-09-01

The COMMIX-1AR/P computer program is designed for analyzing the steady-state and transient aspects of single-phase fluid flow and heat transfer in three spatial dimensions. This version is an extension of the modeling in COMMIX-1A to include multiple fluids in physically separate regions of the computational domain, modeling descriptions for pumps, radiation heat transfer between surfaces of the solids which are embedded in or surround the fluid, a k-{var_epsilon} model for fluid turbulence, and improved numerical techniques. The porous-medium formulation in COMMIX allows the program to be applied to a wide range of problems involving both simple and complex geometrical arrangements. The input preparation and execution procedures are presented for the COMMIX-1AR/P program and several postprocessor programs which produce graphical displays of the calculated results.

Avelumab, an Anti-Programmed Death-Ligand 1 Antibody, In Patients With Refractory Metastatic Urothelial Carcinoma: Results From a Multicenter, Phase Ib Study.

Science.gov (United States)

Apolo, Andrea B; Infante, Jeffrey R; Balmanoukian, Ani; Patel, Manish R; Wang, Ding; Kelly, Karen; Mega, Anthony E; Britten, Carolyn D; Ravaud, Alain; Mita, Alain C; Safran, Howard; Stinchcombe, Thomas E; Srdanov, Marko; Gelb, Arnold B; Schlichting, Michael; Chin, Kevin; Gulley, James L

2017-07-01

Purpose We assessed the safety and antitumor activity of avelumab, a fully human anti-programmed death-ligand 1 (PD-L1) IgG1 antibody, in patients with refractory metastatic urothelial carcinoma. Methods In this phase Ib, multicenter, expansion cohort, patients with urothelial carcinoma progressing after platinum-based chemotherapy and unselected for PD-L1 expression received avelumab 10 mg/kg intravenously every 2 weeks. The primary objectives were safety and tolerability. Secondary objectives included confirmed objective response rate (Response Evaluation Criteria in Solid Tumors [RECIST] version 1.1), progression-free survival, overall survival (OS), and PD-L1-associated clinical activity. PD-L1 positivity was defined as expression by immunohistochemistry on ≥ 5% of tumor cells. Results Forty-four patients were treated with avelumab and followed for a median of 16.5 months (interquartile range, 15.8 to 16.7 months). The data cutoff was March 19, 2016. The most frequent treatment-related adverse events of any grade were fatigue/asthenia (31.8%), infusion-related reaction (20.5%), and nausea (11.4%). Grades 3 to 4 treatment-related adverse events occurred in three patients (6.8%) and included asthenia, AST elevation, creatine phosphokinase elevation, and decreased appetite. The confirmed objective response rate by independent central review was 18.2% (95% CI, 8.2% to 32.7%; five complete responses and three partial responses). The median duration of response was not reached (95% CI, 12.1 weeks to not estimable), and responses were ongoing in six patients (75.0%), including four of five complete responses. Seven of eight responding patients had PD-L1-positive tumors. The median progression-free survival was 11.6 weeks (95% CI, 6.1 to 17.4 weeks); the median OS was 13.7 months (95% CI, 8.5 months to not estimable), with a 12-month OS rate of 54.3% (95% CI, 37.9% to 68.1%). Conclusion Avelumab was well tolerated and associated with durable responses and prolonged

Avelumab, an Anti–Programmed Death-Ligand 1 Antibody, In Patients With Refractory Metastatic Urothelial Carcinoma: Results From a Multicenter, Phase Ib Study

Science.gov (United States)

Apolo, Andrea B.; Infante, Jeffrey R.; Balmanoukian, Ani; Patel, Manish R.; Wang, Ding; Kelly, Karen; Mega, Anthony E.; Britten, Carolyn D.; Ravaud, Alain; Mita, Alain C.; Safran, Howard; Stinchcombe, Thomas E.; Srdanov, Marko; Gelb, Arnold B.; Schlichting, Michael; Chin, Kevin; Gulley, James L.

2017-01-01

Purpose We assessed the safety and antitumor activity of avelumab, a fully human anti–programmed death-ligand 1 (PD-L1) IgG1 antibody, in patients with refractory metastatic urothelial carcinoma. Methods In this phase Ib, multicenter, expansion cohort, patients with urothelial carcinoma progressing after platinum-based chemotherapy and unselected for PD-L1 expression received avelumab 10 mg/kg intravenously every 2 weeks. The primary objectives were safety and tolerability. Secondary objectives included confirmed objective response rate (Response Evaluation Criteria in Solid Tumors [RECIST] version 1.1), progression-free survival, overall survival (OS), and PD-L1–associated clinical activity. PD-L1 positivity was defined as expression by immunohistochemistry on ≥ 5% of tumor cells. Results Forty-four patients were treated with avelumab and followed for a median of 16.5 months (interquartile range, 15.8 to 16.7 months). The data cutoff was March 19, 2016. The most frequent treatment-related adverse events of any grade were fatigue/asthenia (31.8%), infusion-related reaction (20.5%), and nausea (11.4%). Grades 3 to 4 treatment-related adverse events occurred in three patients (6.8%) and included asthenia, AST elevation, creatine phosphokinase elevation, and decreased appetite. The confirmed objective response rate by independent central review was 18.2% (95% CI, 8.2% to 32.7%; five complete responses and three partial responses). The median duration of response was not reached (95% CI, 12.1 weeks to not estimable), and responses were ongoing in six patients (75.0%), including four of five complete responses. Seven of eight responding patients had PD-L1–positive tumors. The median progression-free survival was 11.6 weeks (95% CI, 6.1 to 17.4 weeks); the median OS was 13.7 months (95% CI, 8.5 months to not estimable), with a 12-month OS rate of 54.3% (95% CI, 37.9% to 68.1%). Conclusion Avelumab was well tolerated and associated with durable responses and

Environmental Restoration Program pollution prevention checklist guide for the facility characterization project phase

International Nuclear Information System (INIS)

1993-09-01

A facility characterization (FC) is conducted to determine the nature and extent contamination at a potential hazardous facility waste site. The information gathered during an FC includes (1) data on the volume and chemical nature of the waste, (2) information on the extent of contamination and the migration potential of the contaminants, (3) preliminary information on evaluation of alternative concepts that can or cannot be considered, and (4)supportive technical and cost data. For the purposes of identification, the following operational phases will be used for definition for this phase of the decommissioning and decontamination process (1) facility characterization before clean up, (2) characterization during clean up, (3) characterization of waste materials, and (4) site characterization after clean up. A key consideration in this process is the prevention of any waste to be generated from these characterization activities. The purpose of this checklist guide is to assist users with incorporating pollution prevention/waste minimization (PP/WM) in all FC phase projects of the Environmental Restoration (ER) Program. This guide will help users document PP/WM activities for technology transfer and reporting requirements. Automated computer screens will be created from the checklist data to assist users with implementing and evaluating waste reduction

Crystal phase transition in LixNa1-xGdF4 solid solution nanocrystals - Tuning of optical properties

KAUST Repository

Bański, Mateusz

2014-01-01

The influence of precursor composition on the crystallization of LixNa1-xGdF4 is investigated and discussed. Nanocrystals are prepared from the thermal decomposition of trifluoroacetates in the presence of trioctylphosphine oxide to provide control over particle size. A crystal phase transition from hexagonal to cubic and to tetragonal is observed by increasing lithium trifluoroacetate (Li-TFA) in the solution. Controlling the composition of LixNa1-xGdF4 nanocrystals results in modified crystal field symmetry and emission properties from doped europium (Eu3+) ions. We report that for lithium (Li+) substitution <15%, the hexagonal crystal field is preferred, while the Eu3+ emission is already tuned, whereas at higher Li+ substitution, a phase change takes place and the number of crystalline matrix defects increases which is reflected in the optical properties of Eu3+. From Eu3+ emission properties, the optimum Li+ content is determined to be ∼6.2% in the prepared LixNa1-xGdF4 nanocrystals.

Ta4AlC3: Phase determination, polymorphism and deformation

International Nuclear Information System (INIS)

Eklund, P.; Palmquist, J.-P.; Hoewing, J.; Trinh, D.H.; El-Raghy, T.; Hoegberg, H.; Hultman, L.

2007-01-01

Ta 4 AlC 3 , a new member of the M n+1 AX n -phase family, has been synthesized and characterized (n = 1-3; M = early transition metal; A A-group element; and X = C and/or N). Phase determination by Rietveld refinement of synchrotron X-ray diffraction data shows that Ta 4 AlC 3 belongs to the P6 3 /mmc space group with a and c lattice parameters of 3.10884 ± 0.00004 A and 24.0776 ± 0.0004 A, respectively. This is shown to be the α-polymorph of Ta 4 AlC 3 , with the same structure as Ti 4 AlN 3 . Lattice imaging by high-resolution transmission electron microscopy demonstrates the characteristic MAX-phase stacking of α-Ta 4 AlC 3 . Three modes of mechanical deformation of α-Ta 4 AlC 3 are observed: lattice bending, kinking and delamination

Weather Avoidance Using Route Optimization as a Decision Aid: An AWIN Topical Study. Phase 1

Science.gov (United States)

1998-01-01

interface into a prototype software testbed. Phase II concludes with a dispatcher and pilot evaluation of the route optimizer decision aid. This document describes work completed in Phase I in contract with NASA Langley August 1998 - December 1998. This report includes: (1) Discuss how weather hazards were identified in partnership with experts, and how weather hazards were prioritized; (2) Static representations of display layouts for integrated planning function (3) Cost function for the 2D route optimizer; (4) Discussion of the method for obtaining, access to raw data of, and the results of the flight deck user information requirements definition; (5) Itemized display format requirements identified for representing weather hazards in a route planning aid.

Mean-field theory for the Tsub(c2)-minimum in the phase diagram of Ersub(1-x)Hosub(x)Rh4B4

International Nuclear Information System (INIS)

Schuh, B.; Grewe, N.

1981-01-01

The experimentally observed shape of the phase boundary between the superconducting and the ferromagnetically ordered state in the reentrant ferromagnetic superconductor compound Ersub(1-x)Hosub(x)Rh 4 B 4 is explained within a simple Ginsburg-Landau mean field theory as resulting from a competition of two order parameters corresponding to the magnetic Ho- and Er-moments respectively. (author)

The 10-year trend of adult diabetes, prediabetes and associated risk factors in Tehran: Phases 1 and 4 of Tehran Lipid and Glucose Study.

Science.gov (United States)

Mahtab, Niroomand; Farzad, Hadaegh; Mohsen, Bahaeddini; Nakisa, Darvishi

Type 2 diabetes is a global problem with significant morbidity and healthcare costs. In this study, we aimed to determine the 10-year trend of diabetes, prediabetes and their risk factors in the adult urban population of Tehran Lipid and Glucose Study (TLGS). In this cross-sectional study, we included all patients above 20 years of age who were registered in phases 1 and 4 of TLGS. Each phase had a 3-year duration. 4580 patients were recruited in each phase (916 patients in each age-group, including 3772 males and 5145 females). Random cluster sampling was used in phase 1 and convenience sampling was used in phase 4. Diabetes and glucose tolerance status were determined according to the 1991 criteria of the American Diabetes Association. In our five age groups, risk factors were compared, which included physical activity, waist circumference, body mass index, education, smoking, lipid profile and family history. Exclusion criteria were placement of an individual in the same age-group in the two phases and pregnancy. We calculated the prevalence of diabetes and dysglycemia in each age-group. Age-specific prevalence rates were determined. Prevalence of risk factors in the two phases were compared using chi-square test and Student t-test. Mann-Whitney U test was used to analyze the variables with non-normal distribution. In this study, 3976 individuals were recruited in phase 1 (2308 women and 1668 men; female to male ratio 1.38) and 4941 individuals were recruited in phase 4 (2837 women and 2104 men; female to male ratio 1.35). Prevalence of prediabetes in all age groups (except for the 30-39 years age-group) were increased in phase 4 compared to phase 1. Prevalence of known diabetes in all age groups were increased in phase 4 compared to phase 1, yet, the increase was significant only in the 30-39 and 60-69 years age groups (1.8% vs. 0.7% and 19.0% vs. 10.2%, respectively). Newly diagnosed diabetes was decreased in all age groups in phase 4, except for the 60

Seismic safety margins research program. Phase I final report - Overview

International Nuclear Information System (INIS)

Smith, P.D.; Dong, R.G.; Bernreuter, D.L.; Bohn, M.P.; Chuang, T.Y.; Cummings, G.E.; Johnson, J.J.; Mensing, R.W.; Wells, J.E.

1981-04-01

The Seismic Safety Margins Research Program (SSMRP) is a multiyear, multiphase program whose overall objective is to develop improved methods for seismic safety assessments of nuclear power plants, using a probabilistic computational procedure. The program is being carried out at the Lawrence Livermore National Laboratory and is sponsored by the U.S. Nuclear Regulatory Commission, Office of Nuclear Regulatory Research. Phase I of the SSMRP was successfully completed in January 1981: A probabilistic computational procedure for the seismic risk assessment of nuclear power plants has been developed and demonstrated. The methodology is implemented by three computer programs: HAZARD, which assesses the seismic hazard at a given site, SMACS, which computes in-structure and subsystem seismic responses, and SEISIM, which calculates system failure probabilities and radioactive release probabilities, given (1) the response results of SMACS, (2) a set of event trees, (3) a family of fault trees, (4) a set of structural and component fragility descriptions, and (5) a curve describing the local seismic hazard. The practicality of this methodology was demonstrated by computing preliminary release probabilities for Unit 1 of the Zion Nuclear Power Plant north of Chicago, Illinois. Studies have begun aimed at quantifying the sources of uncertainty in these computations. Numerous side studies were undertaken to examine modeling alternatives, sources of error, and available analysis techniques. Extensive sets of data were amassed and evaluated as part of projects to establish seismic input parameters and to produce the fragility curves. (author)

TEAD4-YAP interaction regulates tumoral growth by controlling cell-cycle arrest at the G1 phase

International Nuclear Information System (INIS)

Takeuchi, Shin; Kasamatsu, Atsushi; Yamatoji, Masanobu; Nakashima, Dai; Endo-Sakamoto, Yosuke; Koide, Nao; Takahara, Toshikazu; Shimizu, Toshihiro; Iyoda, Manabu; Ogawara, Katsunori; Shiiba, Masashi; Tanzawa, Hideki; Uzawa, Katsuhiro

2017-01-01

TEA domain transcription factor 4 (TEAD4), which has critical functions in the process of embryonic development, is expressed in various cancers. However, the important role of TEAD4 in human oral squamous cell carcinomas (OSCCs) remain unclear. Here we investigated the TEAD4 expression level and the functional mechanism in OSCC using quantitative reverse transcriptase-polymerase chain reaction, Western blot analysis, and immunohistochemistry. Furthermore, TEAD4 knockdown model was used to evaluate cellular proliferation, cell-cycle analysis, and the interaction between TEAD4 and Yes-associated protein (YAP) which was reported to be a transcription coactivator of cellular proliferation. In the current study, we found that TEAD4 expression increased significantly in vitro and in vivo and correlated with tumoral size in OSCC patients. TEAD4 knockdown OSCC cells showed decreased cellular proliferation resulting from cell-cycle arrest in the G1 phase by down-regulation of cyclins, cyclin-dependent kinases (CDKs), and up-regulation of CDK inhibitors. We also found that the TEAD4-YAP complex in the nuclei may be related closely to transcriptions of G1 arrest-related genes. Taken together, we concluded that TEAD4 might play an important role in tumoral growth and have potential to be a therapeutic target in OSCCs. - Highlights: • TEAD4 contributes to tumor progression in OSCCs. • TEAD4 knockdown results in cell-cycle arrest at the G1phase in OSCC cells. • In TEAD4 knockdown cells, the amount of YAP in the nucleus decreases. • Activation of the TEAD4-YAP complex is an important factor in OSCC tumor growth. • TEAD4 might be a critical biomarker and a therapeutic target for OSCCs.

AMOS Phase 4 program

Science.gov (United States)

Chapman, J.; McCormick, P.

1980-04-01

This report summarizes the activities which have occurred at the ARPA Maui Optical Site (AMOS) during the period 1 Jan 78 through 31 Dec 78. These activities have taken advantage of the AMOS Facility which was developed by APRA and now serves as a multipurpose advanced optical testbed. This report contains a complete summary of the development of AMOS, a description of the assets available and summarizes the major accomplishments.

Development of a KSC test and flight engineering oriented computer language, Phase 1

Science.gov (United States)

Case, C. W.; Kinney, E. L.; Gyure, J.

1970-01-01

Ten, primarily test oriented, computer languages reviewed during the phase 1 study effort are described. Fifty characteristics of ATOLL, ATLAS, and CLASP are compared. Unique characteristics of the other languages, including deficiencies, problems, safeguards, and checking provisions are identified. Programming aids related to these languages are reported, and the conclusions resulting from this phase of the study are discussed. A glossary and bibliography are included. For the reports on phase 2 of the study, see N71-35027 and N71-35029.

FLICA-4 (version 1). A computer code for three dimensional thermal analysis of nuclear reactor cores

International Nuclear Information System (INIS)

Raymond, P.; Allaire, G.; Boudsocq, G.; Caruge, D.; Gramont, T. de; Toumi, I.

1995-01-01

FLICA-4 is a thermal-hydraulic computer code, developed at the French Atomic Energy Commission (CEA) for three-dimensional steady-state or transient two-phase flow, and aimed at design and safety thermal analysis of nuclear reactor cores. It is available for various UNIX workstations and CRAY computers under UNICOS.It is based on four balance equations which include three balance equations for the mixture and a mass balance equation for the less concentrated phase which allows for the calculation of non equilibrium flows such as sub-cooled boiling and superheated steam. A drift velocity model takes into account the velocity unbalance between phases. The equations are solved using a finite volume numerical scheme. Typical running time, specific features (coupling with other codes) and auxiliary programs are presented. 1 tab., 9 refs

Binding of complement proteins C1q and C4bp to serum amyloid P component (SAP) in solid contra liquid phase

DEFF Research Database (Denmark)

Sørensen, Inge Juul; Nielsen, EH; Andersen, Ove

1996-01-01

Serum amyloid P component (SAP), a member of the conserved pentraxin family of plasma proteins, binds calcium dependently to its ligands. The authors investigated SAPs interaction with the complement proteins C4b binding protein (C4bp) and C1q by ELISA, immunoelectrophoresis and electron microscopy....... Binding of these proteins to SAP was demonstrated when SAP was immobilized using F(ab')2 anti-SAP, but not when SAP reacted with these proteins in liquid phase; thus the binding to human SAP was markedly phase state dependent. Presaturation of solid phase SAP with heparin, which binds SAP with high...... affinity, did not interfere with the subsequent binding of C4bp or C1q to SAP. In contrast, collagen I and IV showed partial competition with the binding of C1q to SAP. Using fresh serum, immobilized native SAP bound C4bp whereas binding of C1q/C1 could not be demonstrated. Altogether the results indicate...

Phased Startup Initiative Phases 3 and 4 Test Plan and Test Specification (OCRWM)

International Nuclear Information System (INIS)

PITNER, A.L.

2000-01-01

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. These tests are described in separate planning documents. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: (1) Define the test scope for the FRS and IWTS; (2) Provide detailed test requirements that can be used to write the specific test procedures; (3) Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and (4) Define specific test objectives and acceptance criteria

Phase transitions in the mixed quadratic-layer antiferromagnets with competing anisotropies K2Cosub(x)Fesub(1-x)F4

International Nuclear Information System (INIS)

Vlak, W.A.H.M.

1985-09-01

The magnetic phases of the randomly mixed two-dimensional antiferromagnet K 2 Cosub(x)Fesub(1-x)F 4 have been explored, utilizing neutron diffraction, Moessbauer absorption spectroscopy, and nuclear magnetic resonance techniques. Ordered phases similar to those found in K 2 FeF 4 and K 2 CoF 4 have been detected for low and high x, respectively. By virtue of the competition between the orthogonal anisotropies of the Fe 2+ and Co 2+ ions a third ordered so-called oblique phase is found for 0.20 2+ and Co 2+ . Studies have been undertaken of the critical behavior, the sublattice magnetization and the magnetization of individual ions, and the magnetic excitations, for compositions x and temperatures T covering all relevant parts of the phase diagram. In addition, the magnetic structure of a system which enters the oblique phase is investigated in an external magnetic field. Strong nonequilibrium behavior, related to random-field effects, has been observed

New all-passive 4x4 planar optical phase diversity network

NARCIS (Netherlands)

Soldano, L.B.; Smit, M.K.; Vreede, De A.H.; Uffelen, van J.W.M.; Verbeek, B.H.; Bennekom, van P.K.; Krom, de W.H.C.; Etten, van W.C.

1991-01-01

The realisation and performance of an all-passive silicon-based 4*4 planar optical hybrid receiver for operation at 1.55- mu m wavelength is reported here for the first time. Measurements show 5 degrees /12 degrees /12 degrees /9 degrees output phase deviations, without tuning or trimming. Network

High Pressure-Temperature Phase Diagram of 1,1-diamino-2,2-dinitroethylene

Science.gov (United States)

Bishop, Matthew; Chellappa, Raja; Liu, Zhenxian; Preston, Daniel; Sandstrom, Mary; Dattelbaum, Dana; Vohra, Yogesh; Velisavljevic, Nenad

2013-06-01

1,1-diamino-2,2-dinitroethelyne (FOX-7) is a less sensitive energetic material with performance comparable to commonly used secondary explosives such as RDX and HMX. At ambient pressure, FOX-7 exhibits complex polymorphism with at least three structurally distinct phases (α, β, and γ) . In this study, we have investigated the high P-T stability of FOX-7 polymorphs using synchrotron mid-infrared (MIR) spectroscopy. At ambient pressure, our MIR spectra confirmed the known α --> β (110 °C) and β --> γ (160 °C) phase transitions; as well as, indicated an additional phase transition, γ --> δ (210°C), with the δ phase being stable up to 250 °C prior to melt/decomposition. In situ MIR spectra obtained during isobaric heating at 0.9 GPa revealed that the α --> β transition occurs at 180 °C, while β --> β + δ phase transition shifted to 300 °C with suppression of γ phase. Decomposition was observed above 325 °C. Based on multiple high P-T measurements, we have established the first high P-T phase diagram of FOX-7. This work was, in part, supported by the US DOE under contract No. DE-AC52-06NA25396 and Science Campaign 2 Program. MB acknowledges additional support from the NSF BD program. Use of NSLS (DE-AC02-98CH10886) beamline U2A (COMPRES, No.EAR01-35554, CDAC).

Program X4TOC4 (Version 86-1). Translation of experimental data from the EXFOR format to a computation format

International Nuclear Information System (INIS)

Cullen, D.E.

1986-09-01

Experimental nuclear reaction data are world-wide compiled in EXFOR format. The computer program X4TOC4 described in the present document translates data from the rather flexible EXFOR format to the more rigid ''computation format'' which is suitable for input to further computer processing of the data including graphical plotting. The program is available costfree from the IAEA Nuclear Data Section, upon request. (author)

Phase space descriptions for simplicial 4D geometries

International Nuclear Information System (INIS)

Dittrich, Bianca; Ryan, James P

2011-01-01

Starting from the canonical phase space for discretized (4D) BF theory, we implement a canonical version of the simplicity constraints and construct phase spaces for simplicial geometries. Our construction allows us to study the connection between different versions of Regge calculus and approaches using connection variables, such as loop quantum gravity. We find that on a fixed triangulation the (gauge invariant) phase space associated with loop quantum gravity is genuinely larger than the one for length and even area Regge calculus. Rather, it corresponds to the phase space of area-angle Regge calculus, as defined in [1] (prior to the imposition of gluing constraints, which ensure the metricity of the triangulation). Finally, we show that for a subclass of triangulations one can construct first-class Hamiltonian and diffeomorphism constraints leading to flat 4D spacetimes.

Anisotropic lattice softening near the structural phase transition in the thermosalient crystal 1,2,4,5-tetrabromobenzene.

Science.gov (United States)

Zakharov, Boris A; Michalchuk, Adam A L; Morrison, Carole A; Boldyreva, Elena V

2018-03-28

The thermosalient effect (crystal jumping on heating) attracts much attention as both an intriguing academic phenomenon and in relation to its potential for the development of molecular actuators but its mechanism remains unclear. 1,2,4,5-Tetrabromobenzene (TBB) is one of the most extensively studied thermosalient compounds that has been shown previously to undergo a phase transition on heating, accompanied by crystal jumping and cracking. The difference in the crystal structures and intermolecular interaction energies of the low- and high-temperature phases is, however, too small to account for the large stress that arises over the course of the transformation. The energy is released spontaneously, and crystals jump across distances that exceed the crystal size by orders of magnitude. In the present work, the anisotropy of lattice strain is followed across the phase transition by single-crystal X-ray diffraction, focusing on the structural evolution from 273 to 343 K. A pronounced lattice softening is observed close to the transition point, with the structure becoming more rigid immediately after the phase transition. The diffraction studies are further supported by theoretical analysis of pairwise intermolecular energies and zone-centre lattice vibrations. Only three modes are found to monotonically soften up to the phase transition, with complex behaviour exhibited by the remaining lattice modes. The thermosalient effect is delayed with respect to the structural transformation itself. This can originate from the martensitic mechanism of the transformation, and the accumulation of stress associated with vibrational switching across the phase transition. The finding of this study sheds more light on the nature of the thermosalient effect in 1,2,4,5-tetrabromobenzene and can be applicable also to other thermosalient compounds.

Anticonvulsant activity of a mGlu(4alpha) receptor selective agonist, (1S,3R,4S)-1-aminocyclopentane-1,2,4-tricarboxylic acid.

Science.gov (United States)

Chapman, A G; Talebi, A; Yip, P K; Meldrum, B S

2001-07-20

The metabotropic Group III agonist, (1S,3R,4S)-1-aminocyclopentane-1,2,4-tricarboxylic acid (ACPT-1), selective for the mGlu(4alpha) receptor, suppresses sound-induced seizures in DBA/2 mice following its intracerebroventricular (i.c.v.) administration (ED(50) 5.6 [2.9-10.7], nmol i.c.v., 15 min, clonic phase) and in genetically epilepsy-prone (GEP) rats following focal administration into the inferior colliculus (ED(50) 0.08 [0.01-0.50], nmol, 60 min, clonic phase). ACPT-1 also protects against clonic seizures induced in DBA/2 mice by the Group I agonist, (RS)-3,5-dihydroxyphenylglycine (3,5-DHPG) (ED(50) 0.60 [0.29-1.2], nmol i.c.v.) and by the Group III antagonist, (RS)-alpha-methylserine-O-phosphate (MSOP) (ED(50) 49.3 [37.9-64.1], nmol i.c.v.). Another Group III agonist, (RS)-4-phosphonophenyl-glycine (PPG), preferentially activating the mGlu(8) receptor, previously shown to protect against sound-induced seizures in DBA/2 mice and GEP rats, also protects against seizures induced in DBA/2 by 3,5-DHPG (ED(50) 3.7 [2.4-5.7], nmol i.c.v.) and by the Group III antagonist, MSOP (ED(50) 40.2 [21.0-77.0], nmol i.c.v.). At very high doses (500 nmol i.c.v. and above), Group III antagonists have pro-convulsant and convulsant activity. The anticonvulsant protection against sound-induced seizures in DBA/2 mice provided by a fully protective dose (20 nmol, i.c.v.) of the mGlu(4) receptor agonist ACPT-1, is partially reversed by the co-administration of the Group III antagonists, MSOP, (RS)-alpha-methyl-4-phosphonophenylglycine (MPPG) or (S)-2-amino-2-methyl-4-phosphonobutanoic acid (MAP4), in the 20-50 nmol dose range. At doses of 50-200 nmol, MPPG and MAP4 cause further reversal of the ACPT-1 anticonvulsant protection, while the MSOP effect on ACPT-1 protection is abolished at higher doses. In contrast, the anticonvulsant protection against sound-induced seizures in DBA/2 mice provided by a fully protective dose (20 nmol, i.c.v.) of the mGlu(8) receptor agonist PPG, is not

A green process for the preparation of 11-{4-[2-(2-hydroxyethoxyethyl]-1-piperazinyl}dibenzo[b,f][1,4]thiazepine

Directory of Open Access Journals (Sweden)

GANESH D. MAHALE

2008-04-01

Full Text Available A green process for the synthesis of 11-{4-[2-(2-hydroxyethoxyethyl]-1-piperazinyl}dibenzo[b,f][1,4]thiazepine by the reaction of 11-(1-piperazinyldibenzo[b,f][1,4]thiazepine or its dihydrochloride salt with 2-(2-chloroethoxyethanol in the presence of an inorganic base and water is reported (conversion 99.9 % in a short time and without any impurities. The metal halides and phase transfer catalyst increase the rate of reaction, especially in water as the solvent.

Phase equilibrium in Rb2MoO4-AMoO4-Zr(MOO4)2 systems (A - bivalent elements)

International Nuclear Information System (INIS)

Ivanova, M.N.; Tsyrenova, G.D.; Bazarova, Zh.G.

1993-01-01

The Rb 2 MoO 4 -AMoO 4 -Zr(MoO 4 ) 2 systems, where A - bivalent elements, were investigated by solid phase reactions, x-ray and differntial thermal analysis methods. Formation of new ternary molybdates was determined. Phase relationships in the Rb 2 MoO 4 -MnMoO 4 -Zr(MoO 4 ) 2 system in subsolidus range (550 deg C) were studied using x-ray analysis data

QUEST/Ada (query utility environment for software testing of Ada: The development of a program analysis environment for Ada, task 1, phase 3

Science.gov (United States)

Brown, David B.

1991-01-01

The results of research and development efforts of the first six months of Task 1, Phase 3 of the project are presented. The goals of Phase 3 are: (1) to further refine the rule base and complete the comparative rule base evaluation; (2) to implement and evaluate a concurrency testing prototype; (3) to convert the complete (unit-level and concurrency) testing prototype to a workstation environment; and (4) to provide a prototype development document to facilitate the transfer of research technology to a working environment. These goals were partially met and the results are summarized.

Programmed death-1 (PD-1)-dependent functional impairment of CD4(+) T cells in recurrent genital papilloma.

Science.gov (United States)

Chang, Dong-Yeop; Song, Sang Hoon; You, Sooseong; Lee, Jino; Kim, Jihye; Racanelli, Vito; Son, Hwancheol; Shin, Eui-Cheol

2014-08-01

Genital papilloma is caused by human papilloma virus (HPV) infection and recurs frequently. Although T cells are known to play a critical role in the control of HPV infection and papilloma development, the function and phenotype of these cells in the lesion remain to be elucidated. In the present study, we examined the function and phenotype of CD4(+) T cells isolated from the lesions of primary (n = 9) and recurrent (n = 11) genital papillomas. In recurrent papillomas, the frequency of proliferating (Ki-67(+)) CD4(+) T cells was significantly reduced compared with primary papillomas. Cytokine production was evaluated by intracellular cytokine staining in anti-CD3/anti-CD28-stimulated CD4(+) T cells. CD4(+) T cells from recurrent lesions showed impaired production of IL-2, IFN-γ, and TNF-α. Of interest, the frequency of cytokine-producing CD4(+) T cells significantly correlated with the frequency of Ki-67(+)CD4(+) T cells. We also studied expression of programmed death-1 (PD-1), a T-cell exhaustion marker. The frequency of PD-1(+)CD4(+) T cells was significantly increased in recurrent lesions and inversely correlated with the frequency of cytokine-producing CD4(+) T cells. The functional significance of PD-1 expression was determined in blocking assays with anti-PD-L1, which restored cytokine production of CD4(+) T cells from recurrent lesions. Taken together, in recurrent genital papilloma lesions, proliferation, and cytokine production by CD4(+) T cells are impaired and the PD-1/PD-L1 interaction is responsible for the functional impairment of CD4(+) T cells.

Life extension program of KORI Unit 1 NPP in Korea

International Nuclear Information System (INIS)

Hong, Sun-Yull

1998-01-01

The two phases of Life extension program for KORI Unit 1 NPP are presented. Phase I is completed. It was concluded that life extension is a feasible option in technical and economic aspects. Detailed analysis of RPV is underway, plan for Phase II is finished. It deals with screening and sorting of all relevant SSCs, detailed life evaluation of SSCs, ageing management program and documentation for license renewal application

Kilowatt isotope power system. Phase II plan. Volume I. Phase II program plan

International Nuclear Information System (INIS)

1978-01-01

The development of a Kilowatt Isotope Power System (KIPS) was begun in 1975 for the purpose of satisfying the power requirements of satellites in the 1980's. The KIPS is a 238 PuO 2 -fueled organic Rankine cycle turbine power system to provide a design output of 500 to 2000 W. Phase II of the overall 3-phase KIPS program is described. This volume presents a program plan for qualifying the organic Rankine power system for flight test in 1982. The program plan calls for the design and fabrication of the proposed flight power system; conducting a development and a qualification program including both environmental and endurance testing, using an electrical and a radioisotope heat source; planning for flight test and spacecraft integration; and continuing ground demonstration system testing to act as a flight system breadboard and to accumulate life data

A New Approach to Commercialization of NASA's Human Research Program Technologies, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This Phase I SBIR proposal describes, "A New Approach to Commercialization of NASA's Human Research Program Technologies." NASA has a powerful research program that...

Phase I of the Near-Term Hybrid Passenger-Vehicle Development Program. Final report

Energy Technology Data Exchange (ETDEWEB)

1980-10-01

Under contract to the Jet Propulsion Laboratory of the California Institute of Technology, Minicars conducted Phase I of the Near-Term Hybrid Passenger Vehicle (NTHV) Development Program. This program led to the preliminary design of a hybrid (electric and internal combustion engine powered) vehicle and fulfilled the objectives set by JPL. JPL requested that the report address certain specific topics. A brief summary of all Phase I activities is given initially; the hybrid vehicle preliminary design is described in Sections 4, 5, and 6. Table 2 of the Summary lists performance projections for the overall vehicle and some of its subsystems. Section 4.5 gives references to the more-detailed design information found in the Preliminary Design Data Package (Appendix C). Alternative hybrid-vehicle design options are discussed in Sections 3 through 6. A listing of the tradeoff study alternatives is included in Section 3. Computer simulations are discussed in Section 9. Section 8 describes the supporting economic analyses. Reliability and safety considerations are discussed specifically in Section 7 and are mentioned in Sections 4, 5, and 6. Section 10 lists conclusions and recommendations arrived at during the performance of Phase I. A complete bibliography follows the list of references.

Investigation into the dehydration of selenate doped Na2M(SO4)2·2H2O (M = Mn, Fe, Co and Ni): Stabilisation of the high Na content alluaudite phases Na3M1.5(SO4)3-1.5x(SeO4)1.5x (M = Mn, Co and Ni) through selenate incorporation

Science.gov (United States)

Driscoll, L. L.; Kendrick, E.; Knight, K. S.; Wright, A. J.; Slater, P. R.

2018-02-01

In this paper we report an investigation into the phases formed on dehydration of Na2M(SO4)2-x(SeO4)x·2H2O (0 ≤ x ≤ 1; M = Mn, Fe, Co and Ni). For the Fe series, all attempts to dehydrate the samples doped with selenate resulted in amorphous products, and it is suspected that a side redox reaction involving the Fe and selenate may be occurring leading to phase decomposition and hence the lack of a crystalline product on dehydration. For M = Mn, Co, Ni, the structure observed was shown to depend upon the transition metal cation and level of selenate doping. An alluaudite phase, Na3M1.5(SO4)3-1.5x(SeO4)1.5x, was observed for the selenate doped compositions, with this phase forming as a single phase for x ≥ 0.5 M = Co, and x = 1.0 M = Ni. For M = Mn, the alluaudite structure is obtained across the series, albeit with small impurities for lower selenate content samples. Although the alluaudite-type phases Na2+2y(Mn/Co)2-y(SO4)3 have recently been reported [1,2], doping with selenate appears to increase the maximum sodium content within the structure. Moreover, the selenate doped Ni based samples reported here are the first examples of a Ni sulfate/selenate containing system exhibiting the alluaudite structure.

Phase I Report, US DOE GRED II Program

Energy Technology Data Exchange (ETDEWEB)

Fairbank Engineering Ltd.

2003-04-23

Noramex Corporation Inc, a Nevada company, owns a 100% interest in geothermal leases at the Blue Mountain Geothermal Area, Humboldt County, Nevada. The company is exploring the site for a geothermal resource suitable for development for electric power generation or In the spring of 2002, Noramex drilled the first geothermal observation hole at Blue Mountain, under a cost-share program with the U.S Department of Energy (DOE), under the DOE's Geothermal Exploration and Resource Definition (GRED) program, (Cooperative Agreement No. DE-FC04-00AL66972). DEEP BLUE No.1 was drilled to a total depth of 672.1 meters (2205 feet) and recorded a maximum temperature of 144.7 C (292.5 F). Noramex Corporation will now drill a second slim geothermal observation test hole at Blue Mountain, designated DEEP BLUE No.2. The hole will be drilled under a cost-share program with the DOE, under the DOE's Geothermal Exploration and Resource Definition II (GRED II) program, (Cooperative Agreement No. DE-FC04-2002AL68297). This report comprises Phase I of Cooperative Agreement No. DE-FC04-2002AL68297 of the GRED II program. The report provides an update on the status of resource confirmation at the Blue Mountain Geothermal Area, incorporating the results from DEEP BLUE No.1, and provides the technical background for a second test hole. The report also outlines the proposed drilling program for slim geothermal observation test hole DEEP BLUE No.2.

NPP A-1 decommissioning - Phase I

International Nuclear Information System (INIS)

Krstenik, A.; Blazek, J.

2000-01-01

Nuclear power plant A-1 with output 150 MW e , with metallic natural uranium fuelled, CO 2 cooled and heavy water moderated reactor had been prematurely finally shut down in 1977. It is necessary to mention that neither operator nor regulatory and other authorities have been prepared for the solution of such situation. During next two consecutive years after shutdown main effort of operator focused on technical and administrative activities which are described in the previous paper together with approach, condition and constraints for NPP A-1 decommissioning as well as the work and research carried out up to the development and approval of the Project for NPP A-1 decommissioning - I. phase. Subject of this paper is description of: (1) An approach to NPP A -1 decommissioning; (2) An approach to development of the project for NPP A-1 decommissioning; (3) Project - tasks, scope, objectives; (4) Mode of the Project realisation; (5) Progress achieved up to the 1999 year. (authors)

The distribution of Th(NO3)4, UO2(NO3)2 and HNO3 between an aqueous phase and an organic tributyl phosphate phase

International Nuclear Information System (INIS)

Nakashima, T.; Zimmer, E.

1984-05-01

The distribution of Th(NO 3 ) 4 , UO 2 (NO 3 ) 2 and HNO 3 between an aqueous phase and an organic phase, consisting of 30 Vol.% tributyl phosphate in dodecane, has been experimentally investigated. About 120 distribution data have been determined in the concentration ranges that can be seen in the THOREX process for reprocessing spent thorium bearing fuel. Based on the experimental data, two computer programs have been developed which make possible interpolations and, to some extent, extrapolations. With model 1, concentrations in the organic phase can be calculated if that in the aqueous phase are known. With model 2, concentrations in the aqueous phase can be calculated vice versa. Besides the description of the calculation models, a large body of calculated data can be found in this report. In a addition, a calculation mode is presented that makes possible the calculation of distribution data for very low thorium concentrations. (orig.) [de

Phase equilibrium in a polarized saturated 3He-4He mixture

International Nuclear Information System (INIS)

Rodrigues, A.; Vermeulen, G.

1997-01-01

We present experimental results on the phase equilibrium of a saturated 3 He- 4 He mixture, which has been cooled to a temperature of 10-15 mK and polarized in a 4 He circulating dilution refrigerator to a stationary polarization of 15 %, 7 times higher than the equilibrium polarization in the external field of 7 T. The pressure dependence of the polarization enhancement in the refrigerator shows that the molar susceptibilities of the concentrated and dilute phase of a saturated 3 He- 4 He mixture are equal at p = 2.60 ± 0.04 bar. This result affects the Fermi liquid parameters of the dilute phase. The osmotic pressure in the dilute phase has been measured as a function of the polarization of the coexisting concentrated phase up to 15 %. We find that the osmotic pressure at low polarization ( < 7 % ) agrees well with thermodynamics using the new Fermi liquid parameters of the dilute phase

Phase Startup Initiative Phases 3 and 4 Test Plan and Test Specification ( OCRWM)

Energy Technology Data Exchange (ETDEWEB)

PAJUNEN, A.L.; LANGEVIN, M.J.

2000-08-07

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: Define the Phase 3 and 4 test scope for the FRS and IWTS; Provide detailed test requirements that can be used to write the specific test procedures; Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and Define specific test objectives and acceptance criteria.

Phase Startup Initiative Phases 3 and 4 Test Plan and Test Specification (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.; LANGEVIN, M.J.

2000-01-01

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: Define the Phase 3 and 4 test scope for the FRS and IWTS; Provide detailed test requirements that can be used to write the specific test procedures; Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and Define specific test objectives and acceptance criteria

High-Pressure Phase Relations and Crystal Structures of Postspinel Phases in MgV2O4, FeV2O4, and MnCr2O4: Crystal Chemistry of AB2O4 Postspinel Compounds.

Science.gov (United States)

Ishii, Takayuki; Sakai, Tsubasa; Kojitani, Hiroshi; Mori, Daisuke; Inaguma, Yoshiyuki; Matsushita, Yoshitaka; Yamaura, Kazunari; Akaogi, Masaki

2018-06-04

We have investigated high-pressure, high-temperature phase transitions of spinel (Sp)-type MgV 2 O 4 , FeV 2 O 4 , and MnCr 2 O 4 . At 1200-1800 °C, MgV 2 O 4 Sp decomposes at 4-7 GPa into a phase assemblage of MgO periclase + corundum (Cor)-type V 2 O 3 , and they react at 10-15 GPa to form a phase with a calcium titanite (CT)-type structure. FeV 2 O 4 Sp transforms to CT-type FeV 2 O 4 at 12 GPa via decomposition phases of FeO wüstite + Cor-type V 2 O 3 . MnCr 2 O 4 Sp directly transforms to the calcium ferrite (CF)-structured phase at 10 GPa and 1000-1400 °C. Rietveld refinements of CT-type MgV 2 O 4 and FeV 2 O 4 and CF-type MnCr 2 O 4 confirm that both the CT- and CF-type structures have frameworks formed by double chains of edge-shared B 3+ O 6 octahedra (B 3+ = V 3+ and Cr 3+ ) running parallel to one of orthorhombic cell axes. A relatively large A 2+ cation (A 2+ = Mg 2+ , Fe 2+ , and Mn 2+ ) occupies a tunnel-shaped space formed by corner-sharing of four double chains. Effective coordination numbers calculated from eight neighboring oxygen-A 2+ cation distances of CT-type MgV 2 O 4 and FeV 2 O 4 and CF-type MnCr 2 O 4 are 5.50, 5.16, and 7.52, respectively. This implies that the CT- and CF-type structures practically have trigonal prism (six-coordinated) and bicapped trigonal prism (eight-coordinated) sites for the A 2+ cations, respectively. A relationship between cation sizes of VIII A 2+ and VI B 3+ and crystal structures (CF- and CT-types) of A 2+ B 2 3+ O 4 is discussed using the above new data and available previous data of the postspinel phases. We found that CF-type A 2+ B 2 3+ O 4 crystallize in wide ionic radius ranges of 0.9-1.4 Å for VIII A 2+ and 0.55-1.1 Å for VI B 3+ , whereas CT-type phases crystallize in very narrow ionic radius ranges of ∼0.9 Å for VIII A 2+ and 0.6-0.65 Å for VI B 3+ . This would be attributed to the fact that the tunnel space of CT-type structure is geometrically less flexible due to the smaller coordination

Phase transformations of 4,4'-biphenyldicarboxylic acid on Cu(001)

NARCIS (Netherlands)

Schwarz, Daniel; van Gastel, Raoul; Zandvliet, Henricus J.W.; Poelsema, Bene

2012-01-01

The growth and structure of 4,4′-biphenyldicarboxylic-acid (BDA) on Cu(001) at temperatures between 300 and 400 K was studied by low energy electron microscopy and μ-LEED. First, the adsorbed BDA molecules form a disordered dilute phase. Once this phase reaches a sufficiently high density, a

Sequence of phase transitions in (NH4)3SiF7.

Science.gov (United States)

Mel'nikova, S V; Molokeev, M S; Laptash, N M; Pogoreltsev, E I; Misyul, S V; Flerov, I N

2017-02-21

Single crystals of silicon double salt (NH 4 ) 3 SiF 7 = (NH 4 ) 2 SiF 6 ·NH 4 F = (NH 4 ) 3 [SiF 6 ]F were grown and studied by the methods of polarization optics, X-ray diffraction and calorimetry. A sequence of symmetry transformations with the temperature change was established: P4/mbm (Z = 2) (G 1 ) ↔ Pbam (Z = 4) (G 2 ) ↔ P2 1 /c (Z = 4) (G 3 ) ↔ P1[combining macron] (Z = 4) (G 4 ) ↔ P2 1 /c (Z = 8) (G 5 ). Crystal structures of different phases were determined. The experimental data were also interpreted by a group-theoretical analysis of the complete condensate of order parameters taking into account critical and noncritical atomic displacements. Strengthening of the N-HF hydrogen bonds can be a driving force of the observed phase transitions.

Inhibition of G1-phase arrest induced by ionizing radiation in hematopoietic cells by overexpression of genes involved in the G1/S-phase transition

International Nuclear Information System (INIS)

Epperly, M.; Berry, L.; Halloran, A.; Greenberger, J.S.

1995-01-01

D-type cyclins and cyclin-dependent kinase (cdk-4) are likely involved in regulating passage of cells through the G 1 phase of the cell cycle. A decrease in the proportion of cells in G 1 , a relatively radiation-sensitive phase of the cell cycle, should result in increased resistance to ionizing radiation; however, the effect of such overexpression on X-ray-induced G 1 -phase arrest is not known. Radiation survival curves were obtained at a dose rate of either 8 cGy/min or 1 Gy/min for subclones of the IL-3-dependent hematopoietic progenitor cell line 32D cl 3 expressing transgenes for either cyclin-D1, D2 or D3 or cdk-4. We compared the results to those with overexpression of the transgene for Bcl-2, whose expression enhances radiation survival and delays apoptosis. Cells overexpressing transgenes for each D-type cyclin or Bcl-2 had an increased number of cells in S phase compared to parent line 32D cl 3; however, overexpression of cdk-4 had no effect on cell cycle distribution. Cell death resulting from withdrawal of IL-3 was not affected by overexpression of D2, cdk-4 or Bcl-2. Flow cytometry 24 h after 5 Gy irradiation demonstrated that overexpression of each G 1 -phase regulatory transgene decreased the proportion of cells at the G 1 /S-phase border. Western analysis revealed induction of cyclin-D protein levels by irradiation, but no change in the D O , but a significant increase in the rvec n for cyclin-D or cdk-4 transgene-overexpressing clones at 1 Gy/min (P 1 /S-phase arrest. 31 refs., 4 figs., 4 tabs

Novel protonated and hydrated n=1 Ruddlesden-Popper phases, HxNa1-xLaTiO4.yH2O, formed by ion-exchange/intercalation reaction

International Nuclear Information System (INIS)

Nishimoto, Shunsuke; Matsuda, Motohide; Miyake, Michihiro

2005-01-01

New derivatives of layered perovskite compounds with H 3 O + ions, H + ions and water molecules in the interlayer, H x Na 1-x LaTiO 4 .yH 2 O, were successfully synthesized by an ion-exchange/intercalation reaction with dilute HCl solution, using an n=1 member of Ruddlesden-Popper phase, NaLaTiO 4 . Powder X-ray diffraction revealed that the layered structure changed from space group P4/nmm with a=3.776(1) and c=13.028(5)A to I4/mmm with a=3.7533(3) and c=28.103(4)A after the ion-exchange/intercalation reaction at pH 5. The change of space group indicates that the perovskite layers are transformed from staggered to an eclipsed configuration through the ion-exchange/intercalation reaction. Thermogravimetric analysis and high-temperature powder X-ray diffraction suggested the existence of the secondary hydrated phase by dehydrating H x Na 1-x LaTiO 4 .yH 2 O at 100 o C

Pollution Reduction Technology Program, Turboprop Engines, Phase 1

Science.gov (United States)

Anderson, R. D.; Herman, A. S.; Tomlinson, J. G.; Vaught, J. M.; Verdouw, A. J.

1976-01-01

Exhaust pollutant emissions were measured from a 501-D22A turboprop engine combustor and three low emission combustor types -- reverse flow, prechamber, and staged fuel, operating over a fuel-air ratio range of .0096 to .020. The EPAP LTO cycle data were obtained for a total of nineteen configurations. Hydrocarbon emissions were reduced from 15.0 to .3 lb/1000 Hp-Hr/cycle, CO from 31.5 to 4.6 lb/1000 Hp-Hr/cycle with an increase in NOx of 17 percent, which is still 25% below the program goal. The smoke number was reduced from 59 to 17. Emissions given here are for the reverse flow Mod. IV combustor which is the best candidate for further development into eventual use with the 501-D22A turboprop engine. Even lower emissions were obtained with the advanced technology combustors.

“Maternal Health and Family Planning Distance Education” experience among physicians: a three-phase study to determine the educational needs, develop education program, and evaluate efficacy of the education administered

Science.gov (United States)

Ciftci, Bestami; Uzel, Nesibe; Ozel, M Onur; Zergeroglu, Sema; Deger, Cetin; Turasan, S Sare; Karakoc, Ayse Gul; Ozbalci, Semra

2016-01-01

Aim This study aims to assess the educational needs of family practitioners and evaluate the efficacy of the ongoing “Maternal Health and Family Planning Distance Education” program conducted by the General Directorate of Health Research (SAGEM) of the Turkish Ministry of Health. Methods This study consisted of three phases. In the first phase, an online survey on maternal health and family planning educational needs was sent to 20,611 physicians via e-mail. Of the 20,611 physicians, 4,729 completed the survey. In the second phase, of the 1,061 physicians registered to the education program, 632 physicians with active participation were included. In the third phase, the preeducation expectations of 287 physicians and posteducation satisfaction of 54 physicians were analyzed with a questionnaire. Results The majority of the physicians were employed in a family health center (97.4%) and practicing for 16–20 years (23.2%) without any prior in-service training (60.9%). High-to-very high educational need was expressed by 56.4% of physicians for pregnancy, delivery, and puerperality. Topics that the physicians, including both those with ≥16 years in practice and without prior in-service training, expressed need for more detailed content were pregnancy, delivery, and puerperality (37.5%); emergency obstetric approach in the primary care setting (33.1%); and gynecological infectious diseases and treatment approach (32.4%). Following the education program, the participants’ expectations were fulfilled in terms of refreshing their knowledge, particularly in the field of Maternal Health and Family Planning (87.1% and 75.9%) and the percentage of participants who expressed that they had sufficient high level knowledge increased from 55% to 68.5%. Conclusion The education on Maternal Health and Family Planning refreshed the knowledge of participants and highly met the preeducation expectations. Determining the educational needs and expectations of the target

Selective isolation of gonyautoxins 1,4 from the dinoflagellate Alexandrium minutum based on molecularly imprinted solid-phase extraction.

Science.gov (United States)

Lian, Ziru; Wang, Jiangtao

2017-09-15

Gonyautoxins 1,4 (GTX1,4) from Alexandrium minutum samples were isolated selectively and recognized specifically by an innovative and effective extraction procedure based on molecular imprinting technology. Novel molecularly imprinted polymer microspheres (MIPMs) were prepared by double-templated imprinting strategy using caffeine and pentoxifylline as dummy templates. The synthesized polymers displayed good affinity to GTX1,4 and were applied as sorbents. Further, an off-line molecularly imprinted solid-phase extraction (MISPE) protocol was optimized and an effective approach based on the MISPE coupled with HPLC-FLD was developed for selective isolation of GTX1,4 from the cultured A. minutum samples. The separation method showed good extraction efficiency (73.2-81.5%) for GTX1,4 and efficient removal of interferences matrices was also achieved after the MISPE process for the microalgal samples. The outcome demonstrated the superiority and great potential of the MISPE procedure for direct separation of GTX1,4 from marine microalgal extracts. Copyright © 2017. Published by Elsevier Ltd.

Steam generator tube integrity program: Phase II, Final report

Energy Technology Data Exchange (ETDEWEB)

Kurtz, R.J.; Bickford, R.L.; Clark, R.A.; Morris, C.J.; Simonen, F.A.; Wheeler, K.R.

1988-08-01

The Steam Generator Tube Integrity Program (SGTIP) was a three phase program conducted for the US Nuclear Regulatory Commission (NRC) by Pacific Northwest Laboratory (PNL). The first phase involved burst and collapse testing of typical steam generator tubing with machined defects. The second phase of the SGTIP continued the integrity testing work of Phase I, but tube specimens were degraded by chemical means rather than machining methods. The third phase of the program used a removed-from-service steam generator as a test bed for investigating the reliability and effectiveness of in-service nondestructive eddy-current inspection methods and as a source of service degraded tubes for validating the Phase I and Phase II data on tube integrity. This report describes the results of Phase II of the SGTIP. The object of this effort included burst and collapse testing of chemically defected pressurized water reactor (PWR) steam generator tubing to validate empirical equations of remaining tube integrity developed during Phase I. Three types of defect geometries were investigated: stress corrosion cracking (SCC), uniform thinning and elliptical wastage. In addition, a review of the publicly available leak rate data for steam generator tubes with axial and circumferential SCC and a comparison with an analytical leak rate model is presented. Lastly, nondestructive eddy-current (EC) measurements to determine accuracy of defect depth sizing using conventional and alternate standards is described. To supplement the laboratory EC data and obtain an estimate of EC capability to detect and size SCC, a mini-round robin test utilizing several firms that routinely perform in-service inspections was conducted.

Steam generator tube integrity program: Phase II, Final report

International Nuclear Information System (INIS)

Kurtz, R.J.; Bickford, R.L.; Clark, R.A.; Morris, C.J.; Simonen, F.A.; Wheeler, K.R.

1988-08-01

The Steam Generator Tube Integrity Program (SGTIP) was a three phase program conducted for the US Nuclear Regulatory Commission (NRC) by Pacific Northwest Laboratory (PNL). The first phase involved burst and collapse testing of typical steam generator tubing with machined defects. The second phase of the SGTIP continued the integrity testing work of Phase I, but tube specimens were degraded by chemical means rather than machining methods. The third phase of the program used a removed-from-service steam generator as a test bed for investigating the reliability and effectiveness of in-service nondestructive eddy-current inspection methods and as a source of service degraded tubes for validating the Phase I and Phase II data on tube integrity. This report describes the results of Phase II of the SGTIP. The object of this effort included burst and collapse testing of chemically defected pressurized water reactor (PWR) steam generator tubing to validate empirical equations of remaining tube integrity developed during Phase I. Three types of defect geometries were investigated: stress corrosion cracking (SCC), uniform thinning and elliptical wastage. In addition, a review of the publicly available leak rate data for steam generator tubes with axial and circumferential SCC and a comparison with an analytical leak rate model is presented. Lastly, nondestructive eddy-current (EC) measurements to determine accuracy of defect depth sizing using conventional and alternate standards is described. To supplement the laboratory EC data and obtain an estimate of EC capability to detect and size SCC, a mini-round robin test utilizing several firms that routinely perform in-service inspections was conducted

Posttest analysis of a 1:4-scale prestressed concrete containment vessel model

International Nuclear Information System (INIS)

Dameron, R.A.; Rashid, Y.R.; Hessheimer, M.F.

2003-01-01

The Nuclear Power Engineering Corporation (NUPEC) of Japan and the U.S. Nuclear Regulatory Commission (NRC), Office of Nuclear Regulatory Research, co-sponsored a Cooperative Containment Research Program at Sandia National Laboratories (SNL) in Albuquerque, New Mexico. As part of the program, a prestressed concrete containment vessel (PCCV) model was subjected to a series of overpressurization tests at SNL beginning in July 2000 and culminating in a functional failure mode or Limit State Test (LST) in September 2000 and a Structural Failure Mode Test (SFMT) in November 2001. The PCCV model, uniformly scaled at 1:4, is representative of the containment structure of an actual Pressurized Water Reactor (PWR) plant (OHI-3) in Japan. The objectives of the pressurization tests were to obtain measurement of the structural response to pressure loading beyond design basis accident in order to validate analytical modeling, to find pressure capacity of the model, and to observe its failure mechanisms. This paper compares results of pretest analytical studies of the PCCV model to the PCCV high pressure test measurements and describes results of post-test analytical studies. These analyses have been performed by ANATECH Corp. under contract with Sandia National Laboratories. The post-test analysis represents the third phase of a comprehensive PCCV analysis effort. The first phase consisted of preliminary analyses to determine what finite element models would be necessary for the pretest prediction analyses, and the second phase consisted of the pretest prediction analyses. The principal objectives of the post-test analyses were: (1) to provide insights to improve the analytical methods for predicting the structural response and failure modes of a prestressed concrete containment, and (2) to evaluate by analysis any phenomena or failure mode observed during the test that had not been explicitly predicted by analysis. In addition to summarizing comparisons between measured

H4 replication-dependent diacetylation and Hat1 promote S-phase chromatin assembly in vivo

Science.gov (United States)

Ejlassi-Lassallette, Aïda; Mocquard, Eloïse; Arnaud, Marie-Claire; Thiriet, Christophe

2011-01-01

While specific posttranslational modification patterns within the H3 and H4 tail domains are associated with the S-phase, their actual functions in replication-dependent chromatin assembly have not yet been defined. Here we used incorporation of trace amounts of recombinant proteins into naturally synchronous macroplasmodia of Physarum polycephalum to examine the function of H3 and H4 tail domains in replication-coupled chromatin assembly. We found that the H3/H4 complex lacking the H4 tail domain was not efficiently recovered in nuclei, whereas depletion of the H3 tail domain did not impede nuclear import but chromatin assembly failed. Furthermore, our results revealed that the proper pattern of acetylation on the H4 tail domain is required for nuclear import and chromatin assembly. This is most likely due to binding of Hat1, as coimmunoprecipitation experiments showed Hat1 associated with predeposition histones in the cytoplasm and with replicating chromatin. These results suggest that the type B histone acetyltransferase assists in shuttling the H3/H4 complex from cytoplasm to the replication forks. PMID:21118997

OCT-4 expression in follicular and luteal phase endometrium: a pilot study

Directory of Open Access Journals (Sweden)

Huber Johannes C

2010-04-01

Full Text Available Abstract Background The stem cell marker Octamer-4 (OCT-4 is expressed in human endometrium. Menstrual cycle-dependency of OCT-4 expression has not been investigated to date. Methods In a prospective, single center cohort study of 98 women undergoing hysteroscopy during the follicular (n = 49 and the luteal (n = 40 phases of the menstrual cycle, we obtained endometrial samples. Specimens were investigated for OCT-4 expression on the mRNA and protein levels using reverse transcriptase polymerase chain reaction (RT-PCR and immunohistochemistry. Expression of OCT-4 was correlated to menstrual cycle phase. Results Of 89 women sampled, 49 were in the follicular phase and 40 were in the luteal phase. OCT-4 mRNA was detected in all samples. Increased OCT-4 mRNA levels in the follicular and luteal phases was found in 35/49 (71% and 27/40 (68% of women, respectively (p = 0.9. Increased expression of OCT-4 protein was identified in 56/89 (63% samples. Increased expression of OCT-4 protein in the follicular and luteal phases was found in 33/49 (67% and 23/40 (58% of women, respectively (p = 0.5. Conclusions On the mRNA and protein levels, OCT-4 is not differentially expressed during the menstrual cycle. Endometrial OCT-4 is not involved in or modulated by hormone-induced cyclical changes of the endometrium.

Radiological Control Technician: Phase 4, Facility practical training attachment

International Nuclear Information System (INIS)

1992-10-01

At DOE sites with more than one facility, and where RCT tasks at each facility may differ, site and facility tasks should be separated. The tasks that are common to all the facilities on the site should be included in Phase II training with the core tasks. Tasks unique to a facility should be added to the training program qualification standard, as an attachment, as Phase IV training. Not all the DOE sites will include Phase IV training in their programs. Phase IV training allows each site to qualify technicians to a select facility. Since the core training for the technicians is standardized, the transfer of technicians between facilities requires that only facility tasks be taught, provided the core qualification is current

A 4-D dataset for validation of crystal growth in a complex three-phase material, ice cream

Science.gov (United States)

Rockett, P.; Karagadde, S.; Guo, E.; Bent, J.; Hazekamp, J.; Kingsley, M.; Vila-Comamala, J.; Lee, P. D.

2015-06-01

Four dimensional (4D, or 3D plus time) X-ray tomographic imaging of phase changes in materials is quickly becoming an accepted tool for quantifying the development of microstructures to both inform and validate models. However, most of the systems studied have been relatively simple binary compositions with only two phases. In this study we present a quantitative dataset of the phase evolution in a complex three-phase material, ice cream. The microstructure of ice cream is an important parameter in terms of sensorial perception, and therefore quantification and modelling of the evolution of the microstructure with time and temperature is key to understanding its fabrication and storage. The microstructure consists of three phases, air cells, ice crystals, and unfrozen matrix. We perform in situ synchrotron X-ray imaging of ice cream samples using in-line phase contrast tomography, housed within a purpose built cold-stage (-40 to +20oC) with finely controlled variation in specimen temperature. The size and distribution of ice crystals and air cells during programmed temperature cycling are determined using 3D quantification. The microstructural evolution of three-phase materials has many other important applications ranging from biological to structural and functional material, hence this dataset can act as a validation case for numerical investigations on faceted and non-faceted crystal growth in a range of materials.

A 4-D dataset for validation of crystal growth in a complex three-phase material, ice cream

International Nuclear Information System (INIS)

Rockett, P; Karagadde, S; Guo, E; Kingsley, M; Lee, P D; Bent, J; Hazekamp, J; Vila-Comamala, J

2015-01-01

Four dimensional (4D, or 3D plus time) X-ray tomographic imaging of phase changes in materials is quickly becoming an accepted tool for quantifying the development of microstructures to both inform and validate models. However, most of the systems studied have been relatively simple binary compositions with only two phases. In this study we present a quantitative dataset of the phase evolution in a complex three-phase material, ice cream. The microstructure of ice cream is an important parameter in terms of sensorial perception, and therefore quantification and modelling of the evolution of the microstructure with time and temperature is key to understanding its fabrication and storage. The microstructure consists of three phases, air cells, ice crystals, and unfrozen matrix. We perform in situ synchrotron X-ray imaging of ice cream samples using in-line phase contrast tomography, housed within a purpose built cold-stage (-40 to +20 o C) with finely controlled variation in specimen temperature. The size and distribution of ice crystals and air cells during programmed temperature cycling are determined using 3D quantification. The microstructural evolution of three-phase materials has many other important applications ranging from biological to structural and functional material, hence this dataset can act as a validation case for numerical investigations on faceted and non-faceted crystal growth in a range of materials. (paper)

Secondary 1 Program of Project P.A.T.H.S.: Process Evaluation Based on the Co-Walker Scheme

Directory of Open Access Journals (Sweden)

Daniel T. L. Shek

2009-01-01

Full Text Available This study examined the implementation quality of the Tier 1 Program (Secondary 1 Curriculum delivered in the second year of the Full Implementation Phase of the Project P.A.T.H.S. (Positive Adolescent Training through Holistic Social Programmes. Under the “Co-Walker Scheme”, systematic observation of curriculum units was conducted in 138 schools. Results indicated that the overall level of program adherence was high, with an average of 82.9%. The mean ratings of the program implementation quality were also high. Despite limitations, the findings of this study suggest that the implementation of the Secondary 1 Program (Tier 1 Program of the Full Implementation Phase was of very high quality. The present findings also provide strong evidence to account for the successful and encouraging outcomes of a major positive youth development program in Hong Kong.

High Performance Computing - Power Application Programming Interface Specification Version 1.4

Energy Technology Data Exchange (ETDEWEB)

Laros III, James H. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); DeBonis, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grant, Ryan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kelly, Suzanne M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Levenhagen, Michael J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Olivier, Stephen Lecler [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Pedretti, Kevin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-10-01

Measuring and controlling the power and energy consumption of high performance computing systems by various components in the software stack is an active research area [13, 3, 5, 10, 4, 21, 19, 16, 7, 17, 20, 18, 11, 1, 6, 14, 12]. Implementations in lower level software layers are beginning to emerge in some production systems, which is very welcome. To be most effective, a portable interface to measurement and control features would significantly facilitate participation by all levels of the software stack. We present a proposal for a standard power Application Programming Interface (API) that endeavors to cover the entire software space, from generic hardware interfaces to the input from the computer facility manager.

An Evaluation System for Training Programs: A Case Study Using a Four-Phase Approach

Science.gov (United States)

Lingham, Tony; Richley, Bonnie; Rezania, Davar

2006-01-01

Purpose: With the increased importance of training in organizations, creating important and meaningful programs are critical to an organization and its members. The purpose of this paper is to suggest a four-phase systematic approach to designing and evaluating training programs that promotes collaboration between organizational leaders, trainers,…

Coupled Electronic and Magnetic Phase Transition in the Infinite-Layer Phase LaSrNiRuO4.

Science.gov (United States)

Patino, Midori Amano; Zeng, Dihao; Bower, Ryan; McGrady, John E; Hayward, Michael A

2016-09-06

Topochemical reduction of the ordered double perovskite LaSrNiRuO6 with CaH2 yields LaSrNiRuO4, an extended oxide phase containing infinite sheets of apex-linked, square-planar Ni(1+)O4 and Ru(2+)O4 units ordered in a checkerboard arrangement. At room temperature the localized Ni(1+) (d(9), S = (1)/2) and Ru(2+) (d(6), S = 1) centers behave paramagnetically. However, on cooling below 250 K the system undergoes a cooperative phase transition in which the nickel spins align ferromagnetically, while the ruthenium cations appear to undergo a change in spin configuration to a diamagnetic spin state. Features of the low-temperature crystal structure suggest a symmetry lowering Jahn-Teller distortion could be responsible for the observed diamagnetism of the ruthenium centers.

Civil Defense, U. S. A.: A Programmed Orientation to Civil Defense. Unit 4. Warning, Emergency Operations, and Support Programs.

Science.gov (United States)

Defense Civil Preparedness Agency (DOD), Battle Creek, MI.

The need for, and a description of, emergency functions required to save lives and protect property in nuclear or natural disasters are presented. Topics discussed include: (1) The Civil Defense Warning System, (2) Introduction to the Emergency Operations Program, (3) Five subprograms of the Emergency Operations Program, (4) Emergency Operations…

Phase identification and superconducting transitions in Sr-doped Pr1.85Ce0.15CuO4+δ

International Nuclear Information System (INIS)

Varela, A.; Vallet-Regi, M.; Gonazalez-Calbet, J.M.

1997-01-01

Sr-doped Pr 1.85 Ce 0.15 CuO 4+δ samples have been prepared with accurate control of the oxygen content. The stability of both T ' and T * phases is strongly dependent on Sr and oxygen content. An electron diffraction study indicates that, in some cases, anionic vacancies are ordered leading to a pseudo-tetragonal superlattice with unit cell parameters 2√2a t xc t . Structural transitions and superconducting phases created by hole doping in such a system are also reported. copyright 1997 Materials Research Society

HTR-proteus pebble bed experimental program core 4: random packing with a 1:1 moderator-to-fuel pebble ratio

Energy Technology Data Exchange (ETDEWEB)

Bess, John D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Montierth, Leland M. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sterbentz, James W. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Briggs, J. Blair [Idaho National Lab. (INL), Idaho Falls, ID (United States); Gougar, Hans D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Snoj, Luka [Jozef Stefan Inst. (IJS), Ljubljana (Slovenia); Lengar, Igor [Jozef Stefan Inst. (IJS), Ljubljana (Slovenia); Koberl, Oliver [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

2014-03-01

In its deployment as a pebble bed reactor (PBR) critical facility from 1992 to 1996, the PROTEUS facility was designated as HTR-PROTEUS. This experimental program was performed as part of an International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on the Validation of Safety Related Physics Calculations for Low Enriched HTGRs. Within this project, critical experiments were conducted for graphite moderated LEU systems to determine core reactivity, flux and power profiles, reaction-rate ratios, the worth of control rods, both in-core and reflector based, the worth of burnable poisons, kinetic parameters, and the effects of moisture ingress on these parameters. One benchmark experiment was evaluated in this report: Core 4. Core 4 represents the only configuration with random pebble packing in the HTR-PROTEUS series of experiments, and has a moderator-to-fuel pebble ratio of 1:1. Three random configurations were performed. The initial configuration, Core 4.1, was rejected because the method for pebble loading, separate delivery tubes for the moderator and fuel pebbles, may not have been completely random; this core loading was rejected by the experimenters. Cores 4.2 and 4.3 were loaded using a single delivery tube, eliminating the possibility for systematic ordering effects. The second and third cores differed slightly in the quantity of pebbles loaded (40 each of moderator and fuel pebbles), stacked height of the pebbles in the core cavity (0.02 m), withdrawn distance of the stainless steel control rods (20 mm), and withdrawn distance of the autorod (30 mm). The 34 coolant channels in the upper axial reflector and the 33 coolant channels in the lower axial reflector were open. Additionally, the axial graphite fillers used in all other HTR-PROTEUS configurations to create a 12-sided core cavity were not used in the randomly packed cores. Instead, graphite fillers were placed on the cavity floor, creating a funnel-like base, to discourage ordering

HTR-PROTEUS PEBBLE BED EXPERIMENTAL PROGRAM CORE 4: RANDOM PACKING WITH A 1:1 MODERATOR-TO-FUEL PEBBLE RATIO

Energy Technology Data Exchange (ETDEWEB)

John D. Bess; Leland M. Montierth

2013-03-01

In its deployment as a pebble bed reactor (PBR) critical facility from 1992 to 1996, the PROTEUS facility was designated as HTR-PROTEUS. This experimental program was performed as part of an International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on the Validation of Safety Related Physics Calculations for Low Enriched HTGRs. Within this project, critical experiments were conducted for graphite moderated LEU systems to determine core reactivity, flux and power profiles, reaction-rate ratios, the worth of control rods, both in-core and reflector based, the worth of burnable poisons, kinetic parameters, and the effects of moisture ingress on these parameters. One benchmark experiment was evaluated in this report: Core 4. Core 4 represents the only configuration with random pebble packing in the HTR-PROTEUS series of experiments, and has a moderator-to-fuel pebble ratio of 1:1. Three random configurations were performed. The initial configuration, Core 4.1, was rejected because the method for pebble loading, separate delivery tubes for the moderator and fuel pebbles, may not have been completely random; this core loading was rejected by the experimenters. Cores 4.2 and 4.3 were loaded using a single delivery tube, eliminating the possibility for systematic ordering effects. The second and third cores differed slightly in the quantity of pebbles loaded (40 each of moderator and fuel pebbles), stacked height of the pebbles in the core cavity (0.02 m), withdrawn distance of the stainless steel control rods (20 mm), and withdrawn distance of the autorod (30 mm). The 34 coolant channels in the upper axial reflector and the 33 coolant channels in the lower axial reflector were open. Additionally, the axial graphite fillers used in all other HTR-PROTEUS configurations to create a 12-sided core cavity were not used in the randomly packed cores. Instead, graphite fillers were placed on the cavity floor, creating a funnel-like base, to discourage ordering

Phase change memory based on SnSe{sub 4} alloy

Energy Technology Data Exchange (ETDEWEB)

Karanja, J.M.; Karimi, P.M.; Njoroge, W.K. [Physics Department, Kenyatta University, P.O. Box 43844, Nairobi (Kenya); Wamwangi, D.M., E-mail: Daniel.Wamwangi@wits.ac.za [School of Physics, University of the Witwatersrand, Private Bag 3, 2050 (South Africa)

2013-01-01

A phase change alloy has been synthesized and characterized. The reversible phase transitions between amorphous and crystalline states of SnSe{sub 4} films have been studied using variable electrical pulses and X-ray diffraction. Temperature dependent sheet resistance measurements have shown two distinct resistivity states of more than two orders of magnitude. This high electrical contrast makes the alloy suitable for nonvolatile phase change memory applications. X-ray diffraction has attributed the large electrical contrast to an amorphous–crystalline phase transition. The nonvolatile memory cells have been fabricated using a simple sandwich structure (metal/chalcogenide thin film/metal). A threshold voltage of 3.71 V has been determined for this phase change random access memory cell. Memory switching was initiated using the voltage pulses of 3.71 V, 90 ns, 1.3 V and 26 μs, for the crystallization and amorphization process, respectively. - Highlights: ► Phase transition of SnSe{sub 4} alloys with high set resistivity of 1.43 Ωm ► High transition temperatures of 174 °C ► Transition due to amorphous–crystalline changes ► Threshold switching at a high threshold voltage of 3.71 V.

Near-term hybrid vehicle program, phase 1. Appendix D: Sensitivity analysis resport

Science.gov (United States)

1979-01-01

Parametric analyses, using a hybrid vehicle synthesis and economics program (HYVELD) are described investigating the sensitivity of hybrid vehicle cost, fuel usage, utility, and marketability to changes in travel statistics, energy costs, vehicle lifetime and maintenance, owner use patterns, internal combustion engine (ICE) reference vehicle fuel economy, and drive-line component costs and type. The lowest initial cost of the hybrid vehicle would be $1200 to $1500 higher than that of the conventional vehicle. For nominal energy costs ($1.00/gal for gasoline and 4.2 cents/kWh for electricity), the ownership cost of the hybrid vehicle is projected to be 0.5 to 1.0 cents/mi less than the conventional ICE vehicle. To attain this ownership cost differential, the lifetime of the hybrid vehicle must be extended to 12 years and its maintenance cost reduced by 25 percent compared with the conventional vehicle. The ownership cost advantage of the hybrid vehicle increases rapidly as the price of fuel increases from $1 to $2/gal.

Phase-inversion tape-casting preparation and significant performance enhancement of Ce0.9Gd0.1O1.95- La0.6Sr0.4Co0.2Fe0.8O3-δ dual-phase asymmetric membrane for oxygen separation

DEFF Research Database (Denmark)

Huang, Hua; Cheng, Shiyang; Gao, Jianfeng

2014-01-01

The dual-phase Ce0.9Gd0.1O1.95–La0.6Sr0.4Co0.2Fe0.8O3−δ asymmetric membrane was prepared via a phase-inversion tape-casting method. The membrane consisted of a thicker porous support layer and a thinner dense layer. When the dense side of the membrane was coated with a La0.6Sr0.4CoO3−δ catalytic...

Phase relations in the systems M2MoO4-Cr2(MoO4)3-Zr(MoO4)2 (M=Li, Na, or Rb)

International Nuclear Information System (INIS)

Bazarov, B.G.; Chimitova, O.D.; Bazarova, Ts.T.; Arkhincheeva, S.I.; Bazarova, Zh.G.

2008-01-01

Phase equilibria in the systems M 2 MoO 4 -Cr 2 (MoO 4 ) 3 -Zr(MoO 4 ) 2 (M=Li, Na, or Rb) were investigated by X-ray powder diffraction analysis, DTA, and IR spectroscopy. The subsolidus structure of the phase diagrams of the systems under study was established. Two phases are formed in the Rb 2 MoO 4 -Cr 2 (MoO 4 ) 3 -Zr(MoO 4 ) 2 system with the molar ratios of the starting components equal to 5:1:1 (S 2 ) and 1:1:1 (S 1 ). Proceeding from isostructural character of Rb 5 FeHf(MoO 4 ) 6 and S 2 , the unit cell parameters are determined for S 2 [ru

Sinorhizobium meliloti sigma factors RpoE1 and RpoE4 are activated in stationary phase in response to sulfite.

Directory of Open Access Journals (Sweden)

Bénédicte Bastiat

Full Text Available Rhizobia are soil bacteria able to establish a nitrogen-fixing symbiosis with legume plants. Both in soil and in planta, rhizobia spend non-growing periods resembling the stationary phase of in vitro-cultured bacteria. The primary objective of this work was to better characterize gene regulation in this biologically relevant growth stage in Sinorhizobium meliloti. By a tap-tag/mass spectrometry approach, we identified five sigma factors co-purifying with the RNA polymerase in stationary phase: the general stress response regulator RpoE2, the heat shock sigma factor RpoH2, and three extra-cytoplasmic function sigma factors (RpoE1, RpoE3 and RpoE4 belonging to the poorly characterized ECF26 subgroup. We then showed that RpoE1 and RpoE4 i are activated upon metabolism of sulfite-generating compounds (thiosulfate and taurine, ii display overlapping regulatory activities, iii govern a dedicated sulfite response by controlling expression of the sulfite dehydrogenase SorT, iv are activated in stationary phase, likely as a result of endogenous sulfite generation during bacterial growth. We showed that SorT is required for optimal growth of S. meliloti in the presence of sulfite, suggesting that the response governed by RpoE1 and RpoE4 may be advantageous for bacteria in stationary phase either by providing a sulfite detoxification function or by contributing to energy production through sulfite respiration. This paper therefore reports the first characterization of ECF26 sigma factors, the first description of sigma factors involved in control of sulphur metabolism, and the first indication that endogenous sulfite may act as a signal for regulation of gene expression upon entry of bacteria in stationary phase.

A dermatitis control program (DeCoP) for head and neck cancer patients receiving radiotherapy. A prospective phase II study

International Nuclear Information System (INIS)

Zenda, Sadamoto; Ishi, Shinobu; Kawashima, Mitsuhiko; Arahira, Satoko; Ichihashi, Tomiko; Tahara, Makoto; Hayashi, Ryuichi; Kishimoto, Seiji

2013-01-01

We speculated that a systematic program to manage radiation dermatitis might decrease the incidence of severe or fatal cases in head and neck cancer patients receiving radiotherapy. Here, we conducted a prospective phase II study to clarify the clinical benefit of a Dermatitis Control Program (DeCoP) that did not use corticosteroids. Head and neck cancer patients scheduled to receive definitive or postoperative radiotherapy were enrolled. Radiation dermatitis was managed with a DeCoP consisting of a three-step ladder: gentle washing; gentle washing and moistening of the wound-healing environment; prevention against infection, gentle washing and moistening of the wound-healing environment. The primary endpoint was the incidence of grade 4 dermatitis. A total of 113 patients were registered between January 2009 and February 2010. Eighty patients received radiotherapy as an initial approach, while the remaining 33 received radiotherapy postoperatively. Grade 3 and 4 dermatitis events occurred in 11 (9.7%) and 0 (0%, 95% confidence interval 0-3.2%) patients, respectively. Median radiation dose at the onset of grade 2 dermatitis was 61.5 Gy (range 36-70 Gy) and median period between onset and recovery was 14 days (range 1-46 days). The Dermatitis Control Program has promising clinical potential. Radiation dermatitis might be manageable if gentle washing and moistening of the wound-healing environment is done. (author)

Structural and thermodynamic similarities of phases in the Li-Tt (Tt = Si, Ge) systems: redetermination of the lithium-rich side of the Li-Ge phase diagram and crystal structures of Li17Si4.0-xGex for x = 2.3, 3.1, 3.5, and 4 as well as Li4.1Ge.

Science.gov (United States)

Zeilinger, Michael; Fässler, Thomas F

2014-10-28

A reinvestigation of the lithium-rich section of the Li-Ge phase diagram reveals the existence of two new phases, Li17Ge4 and Li4.10Ge (Li16.38Ge4). Their structures are determined by X-ray diffraction experiments of large single crystals obtained from equilibrated melts with compositions Li95Ge5 and Li85Ge15. Excess melt is subsequently removed through isothermal centrifugation at 400 °C and 530 °C, respectively. Li17Ge4 crystallizes in the space group F4[combining macron]3m (a = 18.8521(3) Å, V = 6700.1(2) Å(3), Z = 20, T = 298 K) and Li4.10Ge (Li16.38Ge4) in Cmcm (a = 4.5511(2) Å, b = 22.0862(7) Å, c = 13.2751(4) Å, V = 1334.37(8) Å(3), Z = 16, T = 123 K). Both phases are isotypic with their Si counterparts and are further representative of the Li17Pb4 and Li4.11Si structure types. Additionally, the solid solutions Li17Si4-xGex follows Vegard's law. A comparison of the GeLin coordination polyhedra shows that isolated Ge atoms are 13- and 14-coordinated in Li17Ge4, whereas in Li16.38Ge4 the Ge atoms possess coordination numbers 12 and 13. Regarding the thermodynamic stability, Li16.38Ge4 is assigned a high-temperature phase existing between ∼400 °C and 627 °C, whereas Li17Ge4 decomposes peritectically at 520-522 °C. Additionally, the decomposition of Li16.38Ge4 below ∼400 °C was found to be very sluggish. These findings are manifested by differential scanning calorimetry, long-term annealing experiments and the results from melt equilibration experiments. Interestingly, the thermodynamic properties of the lithium-rich tetrelides Li17Tt4 and Li4.1Tt (Li16.4Tt4) are very similar (Tt = Si, Ge). Besides Li15Tt4, Li14Tt6, Li12Tt7, and LiTt, the title compounds are further examples of isotypic tetrelides in the systems Li-Tt.

Phase transitions in solid Kr-CH4 solutions and rotational excitations in phase II

International Nuclear Information System (INIS)

Bagatskii, M.I.; Mashchenko, D.A.; Dudkin, V.V.

2007-01-01

The heat capacity C p of solid Kr-n CH 4 solutions with the CH 4 concentrations n=0.82, 0.86, 0.90 as well as solutions with n=0.90, 0.95 doped with 0.002 O 2 impurity has been investigated under equilibrium vapor pressure over the internal 1-24 K. The (T,n)-phase diagram was refined and the region of two-phase states was determined for Kr-n CH 4 solid solutions. The contribution of the rotational subsystem, C r ot, to the heat capacity of the solutions has been separated. Analysis of C r ot(T) at T 1 and E 2 between the tunnel levels of the A-, T- and A-, E--nuclear-spin species of CH 4 molecules in the orientationally ordered subsystem, and to determine the effective energy gaps E 1 between lowest levels of the A- and T- species. The relations τ(n) and E 1 (n) stem from changes of the effective potential field caused as the replacement of CH 4 molecules by Kr atoms at sites of the ordered sublattices. The effective gaps E L between a group of tunnel levels of the ground-state liberation state and the nearest group of excited levels of the liberation state of the ordered CH 4 molecules in the solutions with n=0.90 (E L =52 K) and 0.95 (E L =55 K) has been estimated

Navy Radon Assessment and Mitigation Program: Work/quality assurance project plan screening phase

International Nuclear Information System (INIS)

1991-03-01

In 1987, the military services of the United States were tasked to take appropriate action to establish an indoor radon assessment and mitigation program. As a result, the Naval Facilities Engineering Command (NAVFACENGCOM) was assigned the responsibility of identifying potential hazards to personnel from exposure to naturally occurring radon gas and prioritizing corrective actions and to coordinating these actions with the major claimants. NAVRAMP is based upon current US Environmental Protection Agency (EPA) guidelines. The program has been separated into four phases. The screening phase will concentrate on evaluating radon levels, based on statistical samples, in those buildings that have been determined to be at most at risk to elevated levels of radon, such as base housing, schools, day-care centers, hospitals, brigs, Base Officer Quarters, and Base Enlisted Quarters. During the assessment phase, every building that contains personnel for over 4 h/day will be evaluated. Mitigation work will be accomplished by Navy or Navy-contracted personnel. HAZWRAP services during the mitigation phase will consist of determining the extent of reduction in radon levels after the mitigation effort. 7 refs., 11 figs

Grain size dependent phase stabilities and presence of a monoclinic (Pm) phase in the morphotropic phase boundary region of (1−x)Bi(Mg{sub 1/2}Ti{sub 1/2})O{sub 3}-xPbTiO{sub 3} piezoceramics

Energy Technology Data Exchange (ETDEWEB)

Upadhyay, Ashutosh; Singh, Akhilesh Kumar, E-mail: akhilesh-bhu@yahoo.com, E-mail: aksingh.mst@itbhu.ac.in [School of Materials Science and Technology, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India)

2015-04-14

Results of the room temperature structural studies on (1−x)Bi(Mg{sub 1/2}Ti{sub 1/2})O{sub 3}-xPbTiO{sub 3} ceramics using Rietveld analysis of the powder x-ray diffraction data in the composition range 0.28 ≤ x ≤ 0.45 are presented. The morphotropic phase boundary region exhibits coexistence of monoclinic (space group Pm) and tetragonal (space group P4 mm) phases in the composition range 0.33 ≤ x ≤ 0.40. The structure is nearly single phase monoclinic (space group Pm) in the composition range 0.28 ≤ x ≤ 0.32. The structure for the compositions with x ≥ 0.45 is found to be predominantly tetragonal with space group P4 mm. Rietveld refinement of the structure rules out the coexistence of rhombohedral and tetragonal phases in the morphotropic phase boundary region reported by earlier authors. The Rietveld structure analysis for the sample x = .35 calcined at various temperatures reveals that phase fraction of the coexisting phases in the morphotropic phase boundary region varies with grain size. The structural parameters of the two coexisting phases also change slightly with changing grain size.

Snubber reduction program at the Byron Station, Unit 1

International Nuclear Information System (INIS)

Arterburn, J.; Bakhtiari, S.

1987-01-01

Commonwealth Edison Company's (CECo's) Byron Station, unit 1, was originally designed with approximately 1200 snubbers supporting the plant's large- and small-bore piping systems. This relatively large number of snubbers is attributed to excessive conservatism in nuclear piping codes and regulations effective during the original piping design. A recent pilot program at CECo's LaSalle County Station, a boiling water reactor plant, demonstrated that a 50% or greater reduction in total snubber population is achievable in plants of this design vintage. Based on the successful results of the pilot program, CECo initiated a full scale snubber reduction program at Byron, a pressurized water reactor plant of the same vintage at the LaSalle County Station. The benefits from a reduced snubber population are described. To realize the maximum potential benefits, all snubbers in the plant were prioritized in order of desirability for removal. The priority designations are discussed. The major results from phase 1 of the Byron program are summarized. The NRC inspection of the project addressed a variety of issues and is discussed. The conclusions that can be drawn from the phase 1 program are summarized

Phase separation phenomena in solutions of poly(2,6-dimethyl-1,4-phenyleneoxide) in mixtures of trichloroethylene, 1-octanol, and methanol: Relationship to membrane formation

NARCIS (Netherlands)

Wijmans, J.G.; Rutten, H.J.J.; Smolders, C.A.

1985-01-01

The phase boundaries in the quaternary system consisting of the polymer poly(2,6-dimethyl-1,4-phenyleneoxide) (PPO[Note ][PPO is a registered trademark of the General Electric Company.]), the solvent trichloroethylene (TCE), and the nonsolvents 1-octanol (OcOH) and methanol (MeOH) are determined.

Luminescent properties of stabled hexagonal phase Sr1-xBaxAl2O4:Eu2+ (x=0.37-0.70)

International Nuclear Information System (INIS)

Wu Qiaoli; Liu Zhen; Jiao Huan

2009-01-01

Stabled hexagonal phase Sr 1-x Ba x Al 2 O 4 :Eu 2+ (x=0.37-0.70) was prepared by solid-state method. Result revealed that the structure behavior of the SrAl 2 O 4 :Eu 2+ calcined at 1350 deg. C in a reducing atmosphere for 5 h strongly depended on the Ba 2+ concentration. With increasing Ba 2+ concentration, a characteristic hexagonal phase can be observed. When 37-70% of the strontium is replaced by barium, the structure of the prepared sample is pure hexagonal. Photoluminescence and excitation spectra of the samples with different x and doped with 2% Eu 2+ were investigated. Changes in the emission spectra were observed in the two different phases. The green emission at 505 nm from Eu 2+ was found to be quite strong in the hexagonal phase. The intensity and peak position of the green luminescence from Eu 2+ changed with increasing content of Ba 2+ . The strongest green emission was obtained from Sr 0.61 Ba 0.37 Al 2 O 4 :Eu 2+ . The decay characteristics of Sr 1-x Ba x Al 2 O 4 :Eu 2+ (x=0.37-0.70) showed that the life times also varied with the value of x. Furthermore, the emission colors and decay times varying with x could be ascribed to the variation of crystal lattice.

Phase formation in Na2MoO4 - MgMoO4 - Cr2(MoO4)3 system

International Nuclear Information System (INIS)

Kotova, I.Yu.; Kozhevnikova, N.M.

1998-01-01

Interaction within Na 2 MoO 4 - MgMoO 4 - Cr 2 (MoO 4 ) 3 ternary system is studied by X ray phase and DTA methods. State diagram of NaCr(MoO 4 ) 2 - MgMoO 4 section is plotted. Production of ternary molybdates of Na 1-x Mg 1-x Cr 1+x (MoO 4 ) 3 , where 0 ≤ x ≤ 0.3, and NaMg 3 Cr(MoO 4 ) 5 composition is ascertained [ru

Grain size dependent phase stabilities and presence of a monoclinic (Pm) phase in the MPB region of (1-x)Bi(Mg_1_/_2Ti_1_/_2)O_3_-_xPbTiO_3

International Nuclear Information System (INIS)

Upadhyay, A.; Singh, A.K.

2016-01-01

The results of the room temperature structural studies on (1-x)Bi(Mg_1_/_2Ti_1_/_2)O_3_-_xPbTiO_3 ceramics using Rietveld analysis of the powder X-ray diffraction data in the composition range 0.28≤x≤0.45 are presented. The morphotropic phase boundary region exhibits coexistence of monoclinic (space group Pm) and tetragonal (space group P4mm) phases in the composition range 0.33≤x≤0.40. The structure is nearly single phase monoclinic (space group Pm) in the composition range 0.28≤x≤0.32. The structure for the compositions with x≥0.45 is found to be predominantly tetragonal with space group P4mm. Rietveld refinement of the structure rules out the coexistence of rhombohedral and tetragonal phases in the morphotropic phase boundary region reported by earlier authors. The Rietveld structure analysis for the sample x=0.35 calcined at various temperatures reveals that phase fraction of the coexisting phases in the morphotropic phase boundary region varies with grain size. The structural parameters of the two coexisting phases also change slightly with changing grain size. (author)

Finite element analysis of a 1:4 scale PCCV model - Korea Atomic Energy Research Institute, Phase 2

International Nuclear Information System (INIS)

Lee, Hong-pyo; Choun, Young-sun

2005-01-01

This report covers phase 2 of the International Standard Problem 48 (ISP48) benchmark on containment integrity. It describes the finite element (FE) analysis results of a 1:4 scale model of a pre-stressed concrete containment vessel (PCCV) model. The objective of the present FE analysis is to evaluate the ultimate internal pressure capacity of the PCCV as well as its failure mechanism when the PCCV model is subjected to a monotonous internal pressure beyond its design pressure. The FE analysis used two concrete failure criteria with the commercial code ABAQUS. One is axisymmetric model with modified Drucker-Prager failure criteria and the other is 3-dimensional model with damaged plasticity model. Finally, the FE analysis results on the ultimate pressure and failure modes have a good agreement with experimental data

Mapping the Superconducting Anti-ferromagnetic C4 Phase in Iron-Pnictides

Science.gov (United States)

Stadel, Ryan; Taddei, Keith; Bugaris, Dan; Lapidus, Saul; Claus, Helmut; Phelan, Daniel; Chung, Duck Young; Kanatzidis, Mercouri; Osborn, Raymond; Rosenkranz, Stephan; Chmaissem, Omar

Following the discovery of the microscopic coexistence of antifermagnetic spin density waves and superconductivity in Ba1-xKxFe2As2 and the low temperature re-entrance to the novel magnetic C4 tetragonal phase in Ba1-xNaxFe2As2, there has been significant interest in developing an understanding of the properties and formation of these phases and analyzing their dependence on temperature and composition in hole-doped 122 alkaline earth metal/iron-pnictides. We describe the mapping of various Ba, Sr, and Ca 122 phase diagrams with systematically controlled levels of hole-doping of alkaline metal onto the alkaline earth metal site, which was investigated via x-ray and neutron diffraction. Our elaborate synthesis, diffraction work, and analysis maps and firmly establishes the C4 phase space in these ternary diagrams as well as the boundary lines that separate the individual phases, and provides natural clues as well as a framework to investigate the stability and formation of the C4 domes that shift location with doping contents in the phase diagrams. Work at Argonne was supported by US DOE, Office of Science, Materials Sciences and Engineering Division.

Observation of a re-entrant phase transition in the molecular complex tris(μ2-3,5-diisopropyl-1,2,4-triazolato-κ2N1:N2trigold(I under high pressure

Directory of Open Access Journals (Sweden)

Christopher H. Woodall

2016-09-01

Full Text Available We report a molecular crystal that exhibits four successive phase transitions under hydrostatic pressure, driven by aurophilic interactions, with the ground-state structure re-emerging at high pressure. The effect of pressure on two polytypes of tris(μ2-3,5-diisopropyl-1,2,4-triazolato-κ2N1:N2trigold(I (denoted Form-I and Form-II has been analysed using luminescence spectroscopy, single-crystal X-ray diffraction and first-principles computation. A unique phase behaviour was observed in Form-I, with a complex sequence of phase transitions between 1 and 3.5 GPa. The ambient C2/c mother cell transforms to a P21/n phase above 1 GPa, followed by a P21/a phase above 2 GPa and a large-volume C2/c supercell at 2.70 GPa, with the previously observed P21/n phase then reappearing at higher pressure. The observation of crystallographically identical low- and high-pressure P21/n phases makes this a rare example of a re-entrant phase transformation. The phase behaviour has been characterized using detailed crystallographic theory and modelling, and rationalized in terms of molecular structural distortions. The dramatic changes in conformation are correlated with shifts of the luminescence maxima, from a band maximum at 14040 cm−1 at 2.40 GPa, decreasing steeply to 13550 cm−1 at 3 GPa. A similar study of Form-II displays more conventional crystallographic behaviour, indicating that the complex behaviour observed in Form-I is likely to be a direct consequence of the differences in crystal packing between the two polytypes.

Deformation-induced phase transformation in 4H–SiC nanopillars

International Nuclear Information System (INIS)

Chen, Bin; Wang, Jun; Zhu, Yiwei; Liao, Xiaozhou; Lu, Chunsheng; Mai, Yiu-Wing; Ringer, Simon P.; Ke, Fujiu; Shen, Yaogen

2014-01-01

The deformation behaviour of single-crystal SiC nanopillars was studied by a combination of in situ deformation transmission electron microscopy and molecular dynamics simulations. An unexpected deformation-induced phase transformation from the 4H hexagonal structure to the 3C face-centred cubic structure was observed in these nanopillars at room temperature. Atomistic simulations revealed that the 4H to 3C phase transformation follows a stick–slip process with initiation and end stresses of 12.1–14.0 and 7.9–9.0 GPa, respectively. The experimentally measured stress of 9–10 GPa for the phase transformation falls within the range of these theoretical upper and lower stresses. The reasons for the phase transformation are discussed. The finding sheds light on the understanding of phase transformation in polytypic materials at low temperature

Charge and structural ordering in the brownmillerite phases: La1-xSrxMnO2.5 (0.24)

International Nuclear Information System (INIS)

Casey, Peter S.; Barker, Daniel; Hayward, Michael A.

2006-01-01

The topotactic reduction of La 1-x Sr x MnO 3 (0.2 1-x Sr x MnO 2.5 brownmillerite phases with NaH is described. Neutron and electron diffraction data show the x=0.25 and 0.2 phases adopt structures with an unusual ordered L-R-L-R alternation of twisted chains of Mn(II) tetrahedra within each anion-deficient layer. This is accompanied by Mn(II)/(III) charge ordering within the remaining MnO 6 octahedral layers. In contrast, the x=0.4 phase adopts a structure in which the twisted chains of tetrahedra are disordered

Phase 1/2 study of cyclin-dependent kinase (CDK)4/6 inhibitor palbociclib (PD-0332991) with bortezomib and dexamethasone in relapsed/refractory multiple myeloma.

Science.gov (United States)

Niesvizky, Ruben; Badros, Ashraf Z; Costa, Luciano J; Ely, Scott A; Singhal, Seema B; Stadtmauer, Edward A; Haideri, Nisreen A; Yacoub, Abdulraheem; Hess, Georg; Lentzsch, Suzanne; Spicka, Ivan; Chanan-Khan, Asher A; Raab, Marc S; Tarantolo, Stefano; Vij, Ravi; Zonder, Jeffrey A; Huang, Xiangao; Jayabalan, David; Di Liberto, Maurizio; Huang, Xin; Jiang, Yuqiu; Kim, Sindy T; Randolph, Sophia; Chen-Kiang, Selina

2015-01-01

This phase 1/2 study was the first to evaluate the safety and efficacy of the cyclin-dependent kinase (CDK) 4/6-specific inhibitor palbociclib (PD-0332991) in sequential combination with bortezomib and dexamethasone in relapsed/refractory multiple myeloma. The recommended phase 2 dose was palbociclib 100 mg orally once daily on days 1-12 of a 21-day cycle with bortezomib 1.0 mg/m2 (intravenous) and dexamethasone 20 mg (orally 30 min pre-bortezomib dosing) on days 8 and 11 (early G1 arrest) and days 15 and 18 (cell cycle resumed). Dose-limiting toxicities were primarily cytopenias; most other treatment-related adverse events were grade≤3. At a bortezomib dose lower than that in other combination therapy studies, antitumor activity was observed (phase 1). In phase 2, objective responses were achieved in 5 (20%) patients; 11 (44%) achieved stable disease. Biomarker and pharmacodynamic assessments demonstrated that palbociclib inhibited CDK4/6 and the cell cycle initially in most patients.

Kentucky Preschool Evaluation Project: Differential Effects, Program Characteristics and Child Outcomes, and Longitudinal and Cumulative Findings. Reports 1-4, 1998-1999.

Science.gov (United States)

Hemmeter, Mary Louise; Townley, Kim; Wilson, Stephen; Epstein, Ann; Hines, Huyi

This document is comprised of four reports related to the evaluation of the Kentucky Preschool Program (KPP), serving 4-year-olds who qualify for the free lunch program and 3- and 4-year-olds with disabilities. Report 1 focuses on the differential effects of the preschool program related to race and to gender. Three key findings are reported: (1)…

Spin glass and ferromagnetic properties of Ce(Cu_1_-_xNi_x)_4Mn alloys: Multicritical points in the magnetic phase diagram

International Nuclear Information System (INIS)

Synoradzki, K.; Toliński, T.

2016-01-01

We report on the CeNi_4Mn (ferromagnet FM) - CeCu_4Mn (spin-glass SG) transformation leading to a complex magnetic phase diagram (MPD). It is verified that all the Ce(Cu_1_-_xNi_x)_4Mn alloys are isostructural and the transformation is governed only by the Cu-Ni substitution. MPD is built based on the magnetic dc/ac susceptibility measurements and reveals SG formation as well as the region of the coexistence of the FM and SG state in the middle range of the Ni concentration. The complex MPD is explained by clusters formation and a competition of interactions between various crystallographic sites of the hexagonal CaCu_5-type structure, mainly the 3g-3g and 3g-2c interactions. The predominance of the SG state is confirmed by the analysis of the frequency dependence of the ac magnetic susceptibility components and the relaxation of the remanent magnetization. Additionally, the presence of two multicritical points is observed. - Highlights: • We fully characterized the magnetic properties of Ce(Cu_1_-_xNi_x)_4Mn alloys. • We show the presence of complex magnetic behaviour due to atomic-site disorder. • Magnetic phase diagram revels mixed-phase ground state. • Two multicritical points on magnetic phase diagram occurs.

Defense Small Business Innovation Research Program (SBIR). Abstracts of Phase 2 Awards 1992

Science.gov (United States)

1992-01-01

into diamond. 2 ARMY SBIR PHASE II AWARDS Transition metals were alloyed at relatively low temperatures to form a thin layer of silicides which lowered...structures. D~uring the phase I program. lDamaskos . Intc. succCssfullN delltonstratet! a cs stpssiol loter :,1I formed by depositinig alte rnat intg layers ...Heights Drive Office: CRI)FC Aica. fiI 96701 Co ntract #: 1)AAA 1 5-93-C-0002if Phonie: 1808)l 486-5381 Ill: Dr, T- J, G. Rasbould Title: Urease -Linked

Early clinical phase of patient's management after polytrauma using 1- and 4-slice helical CT

International Nuclear Information System (INIS)

Kloeppel, R.; Kahn, T.; Schreiter, D.; Dietrich, J.; Josten, C.

2002-01-01

In the early clinical phase the comprehensive imaging of patients with multiple trauma using helical CT is already established. Aim of this study was to assess whether MSCT may improve the patient management and the diagnostic results.The procedure is designed as follows: after life-thretening treatment x-ray of chest and ultrasound are carried out in the emergency room. Then the patient is moved to CT. From 1998 to december 2000 241 patients were examined using a single slice helical CT (Somatom plus 4), in 2001 79 patients using a 4-slice helical CT (Somatom VZ, Siemens Med.Sol.). After CT selected radiograms of the extremities were taken.359 of 360 procedures were carried out successfully. Excluding 1 case (death during 1-sl. h CT) all relevant lesions of head, neck, and body were diagnosed. Although the patients had an injury severity score of ∼30. The change from 1slice-helical CT to 4 slice-helical CT allowed us to reduce the stay in the CT room from 28 to 16 min. The total lethality decreased by ∼4%.Advantages for the patient arose from the standardized examination protocol using multislice CT. If integrated in an interdisciplinary management concept, it is a good compromise between examination time, comprehensive diagnostic imaging, life-saving therapeutic procedures, and therapy planning. (orig.) [de

Aberration corrected STEM of defects in epitaxial n=4 Ruddlesden-Popper phase Can+1MnnO3n+1

International Nuclear Information System (INIS)

Wang, P; Bleloch, A L; Goodhew, P J; Yan, L; Niu, H J; Rosseinsky, M J; Chalker, P R

2008-01-01

Defects in Ruddlesden-Popper phase CaO·[(CaMnO 3 )] 4 epitaxial films grown on SrTiO 3 (001) by pulsed laser deposition have been investigated using high angle annular dark field imaging in an aberration-corrected STEM. The stacking faults perpendicular and parallel to the substrate formed during the growth are discussed in detail. The desired n = 4 RP phase is imaged and chemically analyzed at the atomic scale using electron energy loss spectroscopy.

Low temperature phase transition and crystal structure of CsMgPO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Orlova, Maria, E-mail: maria.p.orlova@gmail.com [Institute of Mineralogy and Petrography, University of Innsbruck, Innrain 52, Innsbruck 6020 (Austria); Khainakov, Sergey [Departamento de Química Física y Analítica, Universidad de Oviedo—CINN, 33006 Oviedo (Spain); Servicios Científico Técnicos, Universidad de Oviedo, 33006 Oviedo (Spain); Michailov, Dmitriy [Department of Chemistry, University of Nizhny Novgorod, 23 Gagarin av., Nizhny Novgorod 603950 (Russian Federation); Perfler, Lukas [Institute of Mineralogy and Petrography, University of Innsbruck, Innrain 52, Innsbruck 6020 (Austria); Langes, Christoph [Institute of Pharmacy, University of Innsbruck, Innrain 52, Innsbruck 6020 (Austria); Kahlenberg, Volker [Institute of Mineralogy and Petrography, University of Innsbruck, Innrain 52, Innsbruck 6020 (Austria); Orlova, Albina [Department of Chemistry, University of Nizhny Novgorod, 23 Gagarin av., Nizhny Novgorod 603950 (Russian Federation)

2015-01-15

CsMgPO{sub 4} doped with radioisotopes is a promising compound for usage as a radioactive medical source. However, a low temperature phase transition at temperatures close to ambient conditions (∼−40 °C) was observed. Information about such kind of structural changes is important in order to understand whether it can cause any problem for medical use of this compound. The phase transition has been investigated in detail using synchrotron powder diffraction, Raman spectroscopy and DFT calculations. The structure undergoes a transformation from an orthorhombic modification, space group Pnma (RT phase) to a monoclinic polymorph, space group P2{sub 1}/n (LT phase). New LT modification adopts similar to RT but slightly distorted unit cell: a=9.58199(2) Å, b=8.95501(1) Å, c=5.50344(2) Å, β=90.68583(1)°, V=472.198(3) Å{sup 3}. CsMgPO{sub 4} belongs to the group of framework compounds and is made up of strictly alternating MgO{sub 4}- and PO{sub 4}-tetrahedra sharing vertices. The cesium counter cations are located in the resulting channel-like cavities. Upon the transformation a combined tilting of the tetrahedra is observed. A comparison with other phase transitions in ABW-type framework compounds is given. - Graphical abstract: Structural behavior of β-tridymite-type phosphate CsMgPO{sub 4}, considered as potential chemical form for radioactive Cs-source has been studied at near ambient temperatures. A phase transition at (∼−40 °C) has been found and investigated. It has been established that the known orthorhombic RT modification, space group Pnma, adopts a monoclinic cell with space group P2{sub 1}/n at low temperatures. In this paper, we present results of structural analysis of changes accompanying this phase transition and discuss its possible impact on the application properties. - Highlights: • β-Tridymite type phosphate CsMgPO{sub 4} undergoes so called translationengleiche phase transition of index 2 at −40 °C. • The structure

High temperature turbine technology program. Phase II. Technology test and support studies. Annual technical progress report, January 1, 1979-December 31, 1979

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

Work performed on the High Temperature Turbine Technology Program, Phase II - Technology Test and Support Studies during the period from January 1, 1979 through December 31, 1979 is summarized. Objectives of the program elements as well as technical progress and problems encountered during this Phase II annual reporting period are presented. Progress on design, fabrication and checkout of test facilities and test rigs is described. LP turbine cascade tests were concluded. 350 hours of testing were conducted on the LP rig engine first with clean distillate fuel and then with fly ash particulates injected into the hot gas stream. Design and fabrication of the turbine spool technology rig components are described. TSTR 60/sup 0/ sector combustor rig fabrication and testing are reviewed. Progress in the design and fabrication of TSTR cascade rig components for operation on both distillate fuel and low Btu gas is described. The new coal-derived gaseous fuel synthesizing facility is reviewed. Results and future plans for the supporting metallurgical programs are discussed.

Electronic properties and structural phase transition in A4 [M4O4] (A=Li, Na, K and Rb; M=Ag and Cu): A first principles study

Science.gov (United States)

Umamaheswari, R.; Yogeswari, M.; Kalpana, G.

2013-02-01

Self-consistent scalar relativistic band structure calculations for AMO (A=Li, Na, K and Rb; M=Ag and Cu) compounds have been performed using the tight-binding linear muffin-tin orbital (TB-LMTO) method within the local density approximation (LDA). At ambient conditions, these compounds are found to crystallize in tetragonal KAgO-type structure with two different space group I-4m2 and I4/mmm. Nowadays, hypothetical structures are being considered to look for new functional materials. AMO compounds have stoichiometry similar to eight-electron half-Heusler materials of type I-I-VI which crystallizes in cubic (C1b) MgAgAs-type structure with space group F-43m. For all these compounds, by interchanging the positions of atoms in the hypothetical cubic structure, three phases (α, β and γ) are formed. The energy-volume relation for these compounds in tetragonal KAgO-type structure and cubic α, β and γ phases of related structure have been obtained. Under ambient conditions these compounds are more stable in tetragonal KAgO-type (I4/mmm) structure. The total energies calculated within the atomic sphere approximation (ASA) were used to determine the ground state properties such as equilibrium lattice parameters, c/a ratio, bulk modulus, cohesive energy and are compared with the available experimental results. The results of the electronic band structure calculations at ambient condition show that LiCuO and NaMO are indirect band gap semiconductors whereas KMO and RbMO are direct band gap semiconductors. At high pressure the band gap decreases and the phenomenon of band overlap metallization occur. Also these compounds undergo structural phase transition from tetragonal I-4m2 phase to cubic α-phase and transition pressures were calculated.

Integration of human reliability analysis into the probabilistic risk assessment process: Phase 1

International Nuclear Information System (INIS)

Bell, B.J.; Vickroy, S.C.

1984-10-01

A research program was initiated to develop a testable set of analytical procedures for integrating human reliability analysis (HRA) into the probabilistic risk assessment (PRA) process to more adequately assess the overall impact of human performance on risk. In this three-phase program, stand-alone HRA/PRA analytic procedures will be developed and field evaluated to provide improved methods, techniques, and models for applying quantitative and qualitative human error data which systematically integrate HRA principles, techniques, and analyses throughout the entire PRA process. Phase 1 of the program involved analysis of state-of-the-art PRAs to define the structures and processes currently in use in the industry. Phase 2 research will involve developing a new or revised PRA methodology which will enable more efficient regulation of the industry using quantitative or qualitative results of the PRA. Finally, Phase 3 will be to field test those procedures to assure that the results generated by the new methodologies will be usable and acceptable to the NRC. This paper briefly describes the first phase of the program and outlines the second

Disposal phase experimental program plan

International Nuclear Information System (INIS)

1997-01-01

The Waste Isolation Pilot Plant (WIPP) facility comprises surface and subsurface facilities, including a repository mined in a bedded salt formation at a depth of 2,150 feet. It has been developed to safely and permanently isolate transuranic (TRU) radioactive wastes in a deep geological disposal site. On April 12, 1996, the DOE submitted a revised Resource Conservation and Recovery Act (RCRA) Part B permit application to the New Mexico Environment Department (NMED). The DOE anticipates receiving an operating permit from the NMED; this permit is required prior to the start of disposal operations. On October 29, 1996, the DOE submitted a Compliance Certification Application (CCA) to the US Environmental Protection Agency (EPA) in accordance with the WIPP land Withdrawal Act (LWA) of 1992 (Public Law 102-579) as amended, and the requirements of Title 40 of the Code of Federal Regulations (40 CFR) Parts 191 and 194. The DOE plans to begin disposal operations at the WIPP in November 1997 following receipt of certification by the EPA. The disposal phase is expected to last for 35 years, and will include recertification activities no less than once every five years. This Disposal Phase Experimental Program (DPEP) Plan outlines the experimental program to be conducted during the first 5-year recertification period. It also forms the basis for longer-term activities to be carried out throughout the 35-year disposal phase. Once the WIPP has been shown to be in compliance with regulatory requirements, the disposal phase gives an opportunity to affirm the compliance status of the WIPP, enhance the operations of the WIPP and the national TRU system, and contribute to the resolution of national and international nuclear waste management technical needs. The WIPP is the first facility of its kind in the world. As such, it provides a unique opportunity to advance the technical state of the art for permanent disposal of long-lived radioactive wastes

Results of the Gallium-Clad Phase 3 and Phase 4 tasks (canceled prior to completion)

International Nuclear Information System (INIS)

Morris, R.N.

1998-08-01

This report summarizes the results of the Gallium-Clad interactions Phase 3 and 4 tasks. Both tasks were to involve examining the out-of-pile stability of residual gallium in short fuel rods with an imposed thermal gradient. The thermal environment was to be created by an electrical heater in the center of the fuel rod and coolant flow on the rod outer cladding. Both tasks were canceled due to difficulties with fuel pellet fabrication, delays in the preparation of the test apparatus, and changes in the Fissile Materials Disposition program budget

Lattice parameter values and phase transitions for the Cu{sub 2}Cd{sub 1-z}Mn{sub z}SnSe{sub 4} and Cu{sub 2}Cd{sub 1-z}Fe{sub z}SnSe{sub 4} alloys

Energy Technology Data Exchange (ETDEWEB)

Moreno, E. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Quintero, M., E-mail: mquinter@ula.v [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Morocoima, M.; Quintero, E.; Grima, P.; Tovar, R.; Bocaranda, P. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Delgado, G.E.; Contreras, J.E. [Laboratorio de Cristalografia, Departamento de Quimica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Mora, A.E.; Briceno, J.M.; Avila Godoy, R.; Fernandez, J.L. [Laboratorio de Analisis Quimico y Estructural de Materiales, Departamento de Fisica, Universidad de Los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Henao, J.A.; Macias, M.A. [Grupo de Investigacion en Quimica Estructural (GIQUE), Facultad de Ciencias, Escuela de Quimica, Universidad Industrial de Santander, Apartado aereo 678, Bucaramanga (Colombia)

2009-11-03

X-ray powder diffraction measurements and differential thermal analysis (DTA) were made on polycrystalline samples of the Cu{sub 2}Cd{sub 1-z}Mn{sub z}SnSe{sub 4} and Cu{sub 2}Cd{sub 1-z}Fe{sub z}SnSe{sub 4} alloy systems. The diffraction patterns were used to show the equilibrium conditions and to derive lattice parameter values. For Cu{sub 2}Cd{sub 0.8}Fe{sub 0.2}SnSe{sub 4} as well as for Cu{sub 2}Cd{sub 0.2}Fe{sub 0.8}SnSe{sub 4} the crystal structures were refined using the Rietveld method. It was found that the internal distortion parameter sigma decreases as Cd is replaced by either Mn and/or Fe. For the Cu{sub 2}Cd{sub 1-z}Mn{sub z}SnSe{sub 4} and Cu{sub 2}Cd{sub 1-z}Fe{sub z}SnSe{sub 4} alloy systems, only two single solid phase fields, the tetragonal stannite alpha(I4-bar2m) and the wurtz-stannite delta (Pmn2{sub 1}) structures were found to occur in the diagram. In addition to the tetragonal stannite alpha phase extra X-ray diffraction lines due to MnSe and/or FeSe{sub 2} were observed for as grown samples in the range 0.7 < z < 1.0. However, it was found that the amount of the extra phase decreased for the compressed samples.

X-ray and neutron single-crystal diffraction on [Rbx(NH4)1-x]3H(SO4)2. I. Refinement of crystal structure of phase II with x=0.11 at 300 K

International Nuclear Information System (INIS)

Loose, A.; Wozniak, K.; Dominiak, P.; Smirnov, L.S.; Natkaniec, I.; Frontas'eva, M.V.; Pomyakushina, E.V.; Baranov, A.I.; Dolbinina, V.V

2006-01-01

The study of [Rb x (NH 4 ) 1-x ] 3 H(SO 4 ) 2 mixed crystals by X-ray single-crystal diffraction is known up to now only for x=0.57 at the temperatures 293 and 180 K. The crystal structures at these temperatures as was determined [1] belong to monoclinic phase II (C2/c sp. gr., Z=4). In accordance with this work, ammonium ions should be considered as deformed tetrahedra. Monoclinic phase II on the x-T phase diagram of [Rb x (NH 4 ) 1-x ] 3 H(SO 4 ) 2 mixed crystals, which has earlier been determined by the dielectric spectroscopy, is stabilized below room temperature if Rb concentration exceeds 9%. The presented results of X-ray and neutron single-crystal diffraction of the [Rb 0.11 (NH 4 ) 0.89 ] 3 H(SO 4 ) 2 mixed crystal at T= 300 K show that ammonium ions could be considered as regular tetrahedra

C language program analysis system (CLAS) part 1: graphical user interface (GUI)

International Nuclear Information System (INIS)

Bhattacharjee, A.K.; Seby, A.; Sen, Gopa; Dhodapkar, S.D.

1994-01-01

CLAS (C Language Program Analysis System) is a reverse engineering tool intended for use in the verification and validation (V and V) phase of software programs developed in the ANSI C language. From the source code, CLAS generates data pertaining to two conceptual models of software programs viz., Entity-Relationship (E-R) model and Control Flow Graphs (CFG) model. Browsing tools within CLAS, make use of this data, to provide different graphical views of the project. Static analysis tools have been developed earlier for analysing assembly language programs. CLAS is a continuation of this work to provide automated support in analysis of ANSI C language programs. CLAS provides an integrated Graphical User Interface (GUI) based environment under which programs can be analysed into the above mentioned models and the analysed data can be viewed using the browsing tools. The GUI of CLAS is implemented using an OPEN LOOK compliant tool kit XVIEW on Sun SPARC IPC workstation running Sun OS 4.1.1 rev. B. This report describes the GUI of CLAS. CLAS is also expected to be useful in other contexts which may involve understanding architecture/structure of already developed C language programs. Such requirements can arise while carrying out activities like code modification, parallelising etc. (author). 5 refs., 13 figs., 1 appendix

Program package for multicanonical simulations of U(1) lattice gauge theory-Second version

Science.gov (United States)

Bazavov, Alexei; Berg, Bernd A.

2013-03-01

A new version STMCMUCA_V1_1 of our program package is available. It eliminates compatibility problems of our Fortran 77 code, originally developed for the g77 compiler, with Fortran 90 and 95 compilers. New version program summaryProgram title: STMC_U1MUCA_v1_1 Catalogue identifier: AEET_v1_1 Licensing provisions: Standard CPC license, http://cpc.cs.qub.ac.uk/licence/licence.html Programming language: Fortran 77 compatible with Fortran 90 and 95 Computers: Any capable of compiling and executing Fortran code Operating systems: Any capable of compiling and executing Fortran code RAM: 10 MB and up depending on lattice size used No. of lines in distributed program, including test data, etc.: 15059 No. of bytes in distributed program, including test data, etc.: 215733 Keywords: Markov chain Monte Carlo, multicanonical, Wang-Landau recursion, Fortran, lattice gauge theory, U(1) gauge group, phase transitions of continuous systems Classification: 11.5 Catalogue identifier of previous version: AEET_v1_0 Journal Reference of previous version: Computer Physics Communications 180 (2009) 2339-2347 Does the new version supersede the previous version?: Yes Nature of problem: Efficient Markov chain Monte Carlo simulation of U(1) lattice gauge theory (or other continuous systems) close to its phase transition. Measurements and analysis of the action per plaquette, the specific heat, Polyakov loops and their structure factors. Solution method: Multicanonical simulations with an initial Wang-Landau recursion to determine suitable weight factors. Reweighting to physical values using logarithmic coding and calculating jackknife error bars. Reasons for the new version: The previous version was developed for the g77 compiler Fortran 77 version. Compiler errors were encountered with Fortran 90 and Fortran 95 compilers (specified below). Summary of revisions: epsilon=one/10**10 is replaced by epsilon/10.0D10 in the parameter statements of the subroutines u1_bmha.f, u1_mucabmha.f, u1wl

HPT Clearance Control: Intelligent Engine Systems-Phase 1

Science.gov (United States)

2005-01-01

The following work has been completed to satisfy the Phase I Deliverables for the "HPT Clearance Control" project under NASA GRC's "Intelligent Engine Systems" program: (1) Need for the development of an advanced HPT ACC system has been very clearly laid out, (2) Several existing and potential clearance control systems have been reviewed, (3) A scorecard has been developed to document the system, performance (fuel burn, range, payload, etc.), thermal, and mechanical characteristics of the existing clearance control systems, (4) Engine size and flight cycle selection for the advanced HPT ACC system has been reviewed with "large engine"/"long range mission" combination showing the most benefit, (5) A scoring criteria has been developed to tie together performance parameters for an objective, data driven comparison of competing systems, and (6) The existing HPT ACC systems have been scored based on this scoring system.

31 CFR 50.4 - Mandatory participation in Program.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Mandatory participation in Program. 50.4 Section 50.4 Money and Finance: Treasury Office of the Secretary of the Treasury TERRORISM RISK... definition of an insurer under the Act is required to participate in the Program. ...

Component Fragility Research Program: Phase 1, Demonstration tests: Volume 1, Summary report

International Nuclear Information System (INIS)

Holman, G.S.; Chou, C.K.; Shipway, G.D.; Glozman, V.

1987-08-01

This report describes tests performed in Phase I of the NRC Component Fragility Research Program. The purpose of these tests was to demonstrate procedures for characterizing the seismic fragility of a selected component, investigating how various parameters affect fragility, and finally using test data to develop practical fragility descriptions suitable for application in probabilistic risk assessments. A three-column motor control center housing motor controllers of various types and sizes as well as relays of different types and manufacturers was subjected to seismic input motions up to 2.5g zero period acceleration. To investigate the effect of base flexibility on the structural behavior of the MCC and on the functional behavior of the electrical devices, multiple tests were performed on each of four mounting configurations: four bolts per column with top bracking, four bolts per column with no top brace, four bolts per column with internal diagonal bracking, and two bolts per column with no top or internal bracking. Device fragility was characterized by contact chatter correlated to local in-cabinet response at the device location. Seismic capacities were developed for each device on the basis of local input motion required to cause chatter; these results were then applied to develop probabilistic fragility curves for each type of device, including estimates of the ''high-confidence low probability of failure'' capacity of each

Small business innovation research: Abstracts of 1984. Phase 1 awards

Science.gov (United States)

1985-01-01

On September 27, 1984, the National Aeronautics and Space Administration announced the selection of Phase I projects for the Small Business Innovation Research Program. These awards resulted from the evaluation of proposals submitted in response to the 1984 Program Solicitation, SBIR 84-1. In order to make available information on the technical content of the Phase I projects supported by the NASA SBIR Program, the abstracts of those proposals which resulted in awards of contracts are given. In addition, the name and address of the firm performing the work are given for those who may desired additional information about the project. Propulsion, aerodynamics, computer techniques, exobiology and composite materials are among the areas covered.

Using the 4 Pillars Practice Transformation Program to Increase Pneumococcal Immunizations for Older Adults: A Cluster-Randomized Trial.

Science.gov (United States)

Zimmerman, Richard K; Brown, Anthony E; Pavlik, Valory N; Moehling, Krissy K; Raviotta, Jonathan M; Lin, Chyongchiou J; Zhang, Song; Hawk, Mary; Kyle, Shakala; Patel, Suchita; Ahmed, Faruque; Nowalk, Mary Patricia

2017-01-01

To test the effectiveness of a step-by step, evidence-based guide, the 4 Pillars Practice Transformation Program, to increase adult pneumococcal vaccination. Randomized controlled cluster trial (RCCT) in Year 1 (June 1, 2013 to May 31, 2014) and pre-post study in Year 2 (June 1, 2014 to January 31, 2015) with data analyzed in 2016. Baseline year was June 1, 2012, to May 31, 2013. Demographic and vaccination data were derived from deidentified electronic medical record extractions. Primary care practices (n = 25) stratified according to metropolitan area (Houston, Pittsburgh), location (rural, urban, suburban), and type (family medicine, internal medicine), randomized to receive the intervention in Year 1 (n = 13) or Year 2 (n = 12). Individuals aged 65 and older at baseline (N = 18,107; mean age 74.2; 60.7% female, 16.5% non-white, 15.7% Hispanic). The 4 Pillars Program, provider education, and one-on-one coaching of practice-based immunization champions. Outcome measures were 23-valent pneumococcal polysaccharide vaccine (PPSV) and pneumococcal conjugate vaccine (PCV) vaccination rates and percentage point (PP) changes in vaccination rates. In the Year 1 RCCT, PPSV vaccination rates increased significantly in all intervention and control groups, with average increases ranging from 6.5 to 8.7 PP (P < .001). The intervention was not related to greater likelihood of PPSV vaccination. In the Year 2 pre-post study, the likelihood of PPSV and PCV vaccination was significantly higher in the active intervention sites than the maintenance sites in Pittsburgh but not in Houston. In a RCCT, PPSV vaccination rates increased in the intervention and control groups in Year 1. In a pre-post study, private primary care practices actively participating in the 4 Pillars Practice Transformation Program improved PPSV and PCV uptake significantly more than practices that were in the maintenance phase of the study. © 2016, Copyright the Authors Journal compilation © 2016, The American

Medium-Energy Nuclear Data Library (MENDLIB): Phase 1

International Nuclear Information System (INIS)

Siciliano, E.R.; Arthur, E.D.

1987-10-01

This document describes an initial step towards the formation of a computerized on-line data library, which would contain published medium-energy experimental data, and which would serve the basic and applied needs of the medium-energy nuclear physics community. The data emphasized in this project will be from measured charged-particle and meson induced nuclear scattering and reactions; an area for which no such data base presently exists. Access to the data will be through a menu-driven program in a user-friendly environment. The project is divided into three phases: Phase 1 involves compilation of Clinton P. Anderson Meson Physics Facility (LAMPF) data from nucleon and pion induced reactions, Phase 2 includes nucleon and pion data from other medium-energy facilities, and Phase 3 includes electron, light-ion, and possibly kaon and anti-nucleon data. The initial goals, the manner in which they would be pursued, and the resources needed to implement Phase 1 (the pilot phase) are discussed in detail. Possible expansion of Phase 1 to attain the envisioned goals of Phase 2 and 3 are briefly outlined. During all stages of the project, input from the community will be sought via the various facility user groups and the American Physical Society Division of Nuclear Physics. It is proposed that the Applied Nuclear Science Group (T-2) of the Los Alamos National Laboratory oversees the development and implementation of this project, and the LAMPF VAX computers be used as the host computers for on-line access

Integrated Data Collection Analysis (IDCA) Program - KClO₄/Aluminum Mixture

Energy Technology Data Exchange (ETDEWEB)

Sandstrom, Mary M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Brown, Geoffrey W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Preston, Daniel N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Pollard, Colin J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Warner, Kirstin F. [Naval Surface Warfare Center (NSWC IHD), Indian Head, MD (United States). Indian Head Division; Sorensen, Daniel N. [Naval Surface Warfare Center (NSWC IHD), Indian Head, MD (United States). Indian Head Division; Remmers, Daniel L. [Naval Surface Warfare Center (NSWC IHD), Indian Head, MD (United States). Indian Head Division; Whinnery, LeRoy L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Shelley, Timothy J. [Air Force Research Lab. (AFRL), Tyndall AFB, FL (United States); Reyes, Jose A. [Applied Research Associates (ARA), Tyndall AFB, FL (United States); Hsu, Peter C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Reynolds, John G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2012-01-17

The Integrated Data Collection Analysis (IDCA) program is conducting a Proficiency Test for Small-Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are the results for impact, friction, electrostatic discharge, and differential scanning calorimetry analysis of a mixture of KClO₄ and aluminum—KClO₄/Al mixture. This material was selected because of the challenge of performing SSST testing of a mixture of two solids. The mixture was found to be: 1) much less sensitive to impact than RDX, (LLNL being the exception) and PETN, 2) more sensitive to friction than RDX and PETN, and 3) extremely sensitive to spark. The thermal analysis showed little or no exothermic character. One prominent endothermic feature was observed in the temperature range studied and identified as a phase transition of KClO₄.

Crystal structure, hydrogen bonding, and sup 8 sup 1 Br NQR of low-temperature phase of 4-aminopyridinium tetrabromoantimonate (3)

CERN Document Server

Hashimoto, M; Fuess, H; Svoboda, I; Ehrenberg, H

2003-01-01

The crystal structure of the low-temperature phase (LTP) of the title compound was determined at 220 K (monoclinic, P2 sub 1 sub / sub c). The 4-aminopyridinium cations (4-NH sub 2 C sub 5 H sub 4 NH sup +) were found to be ordered in LTP, while being severely disordered in the room-temperature phase (monoclinic, C2/c). The tetrabromoantimonate anions (SbBr sub 4 sup -) were incorporated into the infinite polyanion chains of irregular SbBr sub 6 octahedra with two-edges sharing. The trans-Br-Sb-Br moiety in the SbBr sub 4 sup - anion was approximately symmetric differing from the asymmetric Br-Sb centre dot centre dot centre dot Br moiety found in LTP of pyridinium tetrabromoantimonate (3). The N-H moieties in both of the pyridine ring and the amino (-NH sub 2) group participate in the formation of N-H centre dot centre dot centre dot Br hydrogen bonds. It was shown that the sup 8 sup 1 Br NQR spectrum of LTP is closely related to the anion structure and the hydrogen bonds. The distinctive anion structures, a...

Phase-separation phenomena in solutions of poly(2,6-dimethyl-1,4 phenylene oxide). II. Differential scanning calorimetry of solutions in toluene

NARCIS (Netherlands)

Koenhen, D.M.; Smolders, C.A.

1977-01-01

The phase-separation phenomena observed in solutions of poly(2,6 dimethyl-1,4 phenylene oxide) in toluene have been investigated by differential scanning calorimetry. These measurements supplement the experimental evidence in favor of the concept that the phase transitions observed are

A Quasi-Type-1 Phase-Locked Loop Structure

DEFF Research Database (Denmark)

Golestan, Saeed; Fernandez, Francisco Daniel Freijedo; Vidal, Ana

2014-01-01

The grid voltage phase and frequency are crucial information in control of most grid connected power electronic based equipment. Most often, a phase-locked loop (PLL) is employed for this purpose. A PLL is a closed-loop feedback control system that the phase of its output signal is related...... to the phase of its input signal. Arguably, the simplest PLL is a type-1 PLL. The type-1 PLLs are characterized by having only one integrator in their control loop and therefore having a high stability margin. However, they suffer from a serious drawback: they cannot achieve zero average steady-state phase...

Diversity oriented high-throughput screening of 1,3,4-oxadiazole modified chlorophenylureas and halogenobenzamides by HPLC with peptidomimetic calixarene-bonded stationary phases.

Science.gov (United States)

Bazylak, Grzegorz; Malak, Anna; Ali, Imran; Borowiak, Teresa; Dutkiewicz, Grzegorz

2008-06-01

Retention profiles in series of the neutral and highly hydrophobic 1,3,4-oxadiazoles containing chlorophenylurea and halogenobenzamide moiety and indicating analgesic activity were determined in the isocratic standard- and narrow-bore HPLC systems employing, respectively, various octadecylsilica and different calixarene bonded stationary phases. When acetonitrile - 2.65 mM phosphoric acid (55 : 45, %, v/v), pH* 3.25, mobile phase was applied retention of these compounds increased with decline of their overall hydrophobicity according to the general preference of more polar compounds by calixarene cavity in time of its non-specific host-guest supramolecular interactions with halogenated substances. The size of calixarene nanocavity and its upper-rim substitution did not change the observed retention order, resolution and selectivity of separation for oxadiazoles. Compared to the retention on the non-end-capped and the highly-end-capped octadecylsilica HPLC column a most improved separation of some regioisomers of halogenated 1,3,4-oxadiazoles were observed on both used calixarene-type HPLC supports. In addition, preliminary data on the self-assembled supramolecular crystal structure of exemplary 1,3,4-oxadiazolchlorophenylurea with cis-elongated conformation was reported and formation of the monovalent inclusion host-guest complexes between 1,3,4-oxadiazoles and each calixarene-type stationary phase was studied with molecular modelling MM+ and AM1 methods. The structural, isomeric and energetic factors leading to the hydrogen bond stabilized inclusion complexes between these species were considered and used for explanation of observed retention sequence and selectivity of 1,3,4-oxadiazoles separation in applied calixarene-based HPLC systems. All these data would be useful in future development of optimized procedures enabling encapsulation of 1,3,4-oxadiazolurea-type drugs with calixarenes.

Computer program to fit a hyperellipse to a set of phase-space points in as many as six dimensions

International Nuclear Information System (INIS)

Wadlinger, E.A.

1980-03-01

A computer program that will fit a hyperellipse to a set of phase-space points in as many as 6 dimensions was written and tested. The weight assigned to the phase-space points can be varied as a function of their distance from the centroid of the distribution. Varying the weight enables determination of whether there is a difference in ellipse orientation between inner and outer particles. This program should be useful in studying the effects of longitudinal and transverse phase-space couplings

Direct evidence for the first-order phase transition at the lower critical temperature in Er/sub 1-x/Ho/sub x/Rh4B4

International Nuclear Information System (INIS)

Lachal, B.; Ishikawa, M.; Junod, A.; Muller, J.

1982-01-01

Using a heat-pulse and a relaxation technique, we have performed an extensive calorimetric investigation on the reetrant superconductors Er/sub 1-x/Ho/sub x/Rh 4 B 4 (x = 0.4 and 0.6) around their lower critical temperature. These experiments revealed a supercooling effect and thermal hystersis, thus establishing the first-order nature of the transition. Based on the measurement of the latent heat, our thermodynamic analysis suggests that the onset of ferromagnetism is lowered by only 55 mK due to the competing superconducting phase. Results of magnetization and ac susceptibility experiments on these compounds are also included

Senescent cells re-engineered to express soluble programmed death receptor-1 for inhibiting programmed death receptor-1/programmed death ligand-1 as a vaccination approach against breast cancer.

Science.gov (United States)

Chen, Zehong; Hu, Kang; Feng, Lieting; Su, Ruxiong; Lai, Nan; Yang, Zike; Kang, Shijun

2018-06-01

Various types of vaccines have been proposed as approaches for prevention or delay of the onset of cancer by boosting the endogenous immune system. We previously developed a senescent-cell-based vaccine, induced by radiation and veliparib, as a preventive and therapeutic tool against triple-negative breast cancer. However, the programmed death receptor-1/programmed death ligand-1 (PD-1/PD-L1) pathway was found to play an important role in vaccine failure. Hence, we further developed soluble programmed death receptor-1 (sPD1)-expressing senescent cells to overcome PD-L1/PD-1-mediated immune suppression while vaccinating to promote dendritic cell (DC) maturity, thereby amplifying T-cell activation. In the present study, sPD1-expressing senescent cells showed a particularly active status characterized by growth arrest and modified immunostimulatory cytokine secretion in vitro. As expected, sPD1-expressing senescent tumor cell vaccine (STCV/sPD-1) treatment attracted more mature DC and fewer exhausted-PD1 + T cells in vivo. During the course of the vaccine studies, we observed greater safety and efficacy for STCV/sPD-1 than for control treatments. STCV/sPD-1 pre-injections provided complete protection from 4T1 tumor challenge in mice. Additionally, the in vivo therapeutic study of mice with s.c. 4T1 tumor showed that STCV/sPD-1 vaccination delayed tumorigenesis and suppressed tumor progression at early stages. These results showed that STCV/sPD-1 effectively induced a strong antitumor immune response against cancer and suggested that it might be a potential strategy for TNBC prevention. © 2018 The Authors. Cancer Science published by John Wiley & Sons Australia, Ltd on behalf of Japanese Cancer Association.

Room temperature chemically oxidized La2CuO4+y: Phase separation induced by thermal treatment

DEFF Research Database (Denmark)

Rial,C.; Moran, E.; Alario-Franco, M.A.

1997-01-01

The structure of roam temperature chemically oxidized La2CuO4+y [y = 0.103(4)] has been refined from powder neutron diffraction data using the space group Bmab. The modifications induced in the CuO2 and the LaO planes by the insertion of oxygen are consistent with the high T-c measured for this m......The structure of roam temperature chemically oxidized La2CuO4+y [y = 0.103(4)] has been refined from powder neutron diffraction data using the space group Bmab. The modifications induced in the CuO2 and the LaO planes by the insertion of oxygen are consistent with the high T-c measured...... a short treatment at 433 K, La2CuO4.103(4) undergoes a phase separation into two phases: phase 1, with estimated y(1) = 0.086(4) and T-cl = 30 K, and phase 2, with estimated y(2) = 0.12(1) and T-c2 = 17 K. By increasing the annealing times, phase 2 transforms to phase I and finally disappears. Therefore...

Resilience Training for Healthcare Staff (RTHS) Implementation Evaluation Phase 1

Science.gov (United States)

2017-01-05

healthcare, Master Resilience Training, MRT, MTF, medical treatment facility, program evaluation , implementation evaluation , OPORD 14-43, resilience...RTHS-certified Master Resilience Trainers (MRTs) among 73 MRTs whose status was confirmed. Seventy-one percent (n = 52) of these MRTs were fulfilling...Healthcare Staff (RTHS) Implementation Evaluation Phase 1 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Start, Amanda

Diversion Path Analysis handbook. Volume 3 (of 4 volumes). Computer Program 1

International Nuclear Information System (INIS)

Schleter, J.C.

1978-11-01

The FORTRAN IV computer program, DPA Computer Program 1 (DPACP-1), is used to assemble and tabulate the data for Specific Diversion Paths (SDPs) identified when performing a Diversion Path Analysis (DPA) in accord with the methodology given in Volume 1. The program requires 255498 bytes exclusive of the operating system. The data assembled and tabulated by DPACP-1 are used by the DPA team to assist in analyzing vulnerabilities, in a plant's material control and material accounting subsystems, to diversion of special nuclear material (SNM) by a knowledgable insider. Based on this analysis, the DPA team can identify, and propose to plant management, modifications to the plant's safeguards system that would eliminate, or reduce the severity of, the identified vulnerabilities. The data are also used by plant supervision when investigating a potential diversion

An Overview of 2014 SBIR Phase 1 and Phase 2 Air-Breathing Propulsion

Science.gov (United States)

Nguyen, Hung D.; Steele, Gynelle C.; Morris, Jessica R.

2015-01-01

NASA's Small Business Innovation Research (SBIR) program focuses on technological innovation by investing in development of innovative concepts and technologies to help NASA mission directorates address critical research needs for Agency programs. This report highlights nine of the innovative SBIR 2014 Phase I and Phase II projects that emphasize one of NASA Glenn Research Center's six core competencies-Air-Breathing Propulsion. The technologies cover a wide spectrum of applications such as development of X-ray computed tomography (CT) imaging method for the measurement of complex 3D ice shapes, phased array techniques for low signal-to-noise ratio wind tunnels, compact kinetic mechanisms for petroleum-derived and alternative aviation fuels, and hybrid electric propulsion systems for a multirotor aircraft. Each featured technology describes an innovation, technical objective, and highlights NASA commercial and industrial applications. This report provides as an opportunity for NASA engineers, researchers, and program managers to learn how NASA SBIR technologies could help their programs and projects, and lead to collaborations and partnerships between the small SBIR companies and NASA that would benefit both.

MABGEL 1: first phase 1 trial of the anti-HIV-1 monoclonal antibodies 2F5, 4E10 and 2G12 as a vaginal microbicide.

Directory of Open Access Journals (Sweden)

Georgina C Morris

Full Text Available BACKGROUND: Monoclonal antibodies (mAbs which potently neutralize a broad range of HIV isolates are potential microbicide candidates. To date, topical application of mAbs in humans and their stability in vaginal secretions has not been studied. OBJECTIVES: To assess the pharmacokinetics and safety of the mAbs 2F5, 4E10 and 2G12 when applied vaginally in women. DESIGN: A randomized, double-blind, placebo-controlled phase 1 trial. METHODS: Twenty-eight healthy, sexually abstinent women administered 2.5 g of gel daily for 12 days containing either 10 or 20 mg/g of each mAb (MABGEL or placebo. Main clinical evaluations and sampling occurred at baseline, 1, 8, and 24 hours post-1st dose and 12 and 36 hours post-12th dose. RESULTS: After adjustment for dilution factors, median levels of 2F5, 4E10 and 2G12 in vaginal secretions at 1 hour post high-dose MABGEL were 7.74, 5.28 and 7.48 mg/ml respectively. Levels of 2F5 and 4E10 declined exponentially thereafter with similar estimated half-lives (4.6 and 4.3 hours. In contrast, 2G12 levels declined more rapidly in the first 8 hours, with an estimated half-life of 1.4 hours during this period. There was no evidence of systemic absorption. There were no significant differences in local or systemic adverse event rates or vaginal flora changes (by qPCR between active and placebo gel arms. Whilst at least 1 adverse event was recorded in 96% of participants, 95% were mild and none were serious. CONCLUSIONS: Vaginal application of 50 mg of each mAb daily was safe over a 12 day period. Median mAb concentrations detected at 8 hours post dose were potentially sufficient to block HIV transmission.2G12 exhibited more rapid elimination from the human vagina than 4E10 and 2F5, likely due to poor stability of 2G12 in acidic human vaginal secretions. Further research is needed to develop mAb-based vaginal microbicides and delivery systems. TRIAL REGISTRATION: ISRCTN 64808733 UK CRN Portfolio 6470.

Neutron scattering investigations of the properties of the x - T phase diagram of Rb1-x(NH4)xI mixed crystals

International Nuclear Information System (INIS)

Smirnov, L.S.; Natkaniec, I.; Savenko, B.N.

2002-01-01

The x - T phase diagram of Rb 1-x (NH 4 ) x I is studied using samples with the ammonium concentration 0.01< x<0.77 over a wide temperature region of 15 to 300 K by neutron powder diffraction and inelastic incoherent neutron scattering. The results of powder diffraction studies show that at low temperatures a phase transition from α-phase to β-phase is observed at ammonium concentrations x = 0.50 and x = 0.66. Inelastic incoherent neutron scattering detects a region of the orientional glass state at ammonium concentrations 0.29< x,0.40

TH-E-17A-08: Estimation of Image Quality of 4-Dimensional Computed Tomography (4DCT) Via Fourier Analysis of Corresponding 1D Breathing Surrogate

Energy Technology Data Exchange (ETDEWEB)

Caraveo, M; McNamara, J; Rimner, A; Yorke, E; Li, G [Memorial Sloan Kettering Cancer Center, New York, NY (United States); Wei, J [City College of New York, New York, NY (United States)

2014-06-15

Purpose: Motion artifacts are common in patient 4DCT, leading to an illdefined tumor volume with variation up to 110% or setting up a poor foundation with low imaging fidelity for tumor motion study. We developed a method to estimate 4DCT image quality by establishing a correlation between the severity of motion artifacts in 4DCT images and the periodicity of corresponding 1D respiratory wave-function (1DRW) surrogate used for 4DCT reconstruction. Methods: Fast Fourier Transformation (FFT) was applied to analyze 1DRW periodicity, defined as the sum of the 5 largest Fourier coefficients, ranging in 0–1. Distortional motion artifacts of cine-scan 4DCT at the junctions of adjacent couchposition scans around the diaphragm were identified in 3 categories: incomplete, overlapping and duplicate. To quantify these artifacts, the discontinuity of the diaphragm at the junctions was measured in distance and averaged along 6 directions in 3 orthogonal views. Mean and sum artifacts per junction (APJ) across the entire diaphragm were calculated in each breathing phase. To make the APJ inter-patient comparable, patientspecific motion was removed from APJ by dividing patient-specific diaphragmatic velocity (displacement divided by the mean period, from FFT analysis of the 1DRW) and the normalized APJ was defined as motion artifact severity (MAS). Twenty-five patients with free-breathing 10-phase 4DCT and corresponding 1DRW surrogate datasets were studied. Results: A mild correlation of 0.56 was found between 1DRW periodicity and 4DCT artifact severity. Higher MAS tends to appear around mid inhalation and mid exhalation and the lowest MAS tends to be around full exhalation. The breathing periodicity of >0.8 possesses minimal motion artifacts. Conclusion: The 1D-4D correlation provides a fast means to estimate 4DCT image quality. Using 1DRW signal, we can retrospectively screen out high-quality 4DCT images for clinical research (periodicity>0.8) and prospectively identify poor

TH-E-17A-08: Estimation of Image Quality of 4-Dimensional Computed Tomography (4DCT) Via Fourier Analysis of Corresponding 1D Breathing Surrogate

International Nuclear Information System (INIS)

Caraveo, M; McNamara, J; Rimner, A; Yorke, E; Li, G; Wei, J

2014-01-01

Purpose: Motion artifacts are common in patient 4DCT, leading to an illdefined tumor volume with variation up to 110% or setting up a poor foundation with low imaging fidelity for tumor motion study. We developed a method to estimate 4DCT image quality by establishing a correlation between the severity of motion artifacts in 4DCT images and the periodicity of corresponding 1D respiratory wave-function (1DRW) surrogate used for 4DCT reconstruction. Methods: Fast Fourier Transformation (FFT) was applied to analyze 1DRW periodicity, defined as the sum of the 5 largest Fourier coefficients, ranging in 0–1. Distortional motion artifacts of cine-scan 4DCT at the junctions of adjacent couchposition scans around the diaphragm were identified in 3 categories: incomplete, overlapping and duplicate. To quantify these artifacts, the discontinuity of the diaphragm at the junctions was measured in distance and averaged along 6 directions in 3 orthogonal views. Mean and sum artifacts per junction (APJ) across the entire diaphragm were calculated in each breathing phase. To make the APJ inter-patient comparable, patientspecific motion was removed from APJ by dividing patient-specific diaphragmatic velocity (displacement divided by the mean period, from FFT analysis of the 1DRW) and the normalized APJ was defined as motion artifact severity (MAS). Twenty-five patients with free-breathing 10-phase 4DCT and corresponding 1DRW surrogate datasets were studied. Results: A mild correlation of 0.56 was found between 1DRW periodicity and 4DCT artifact severity. Higher MAS tends to appear around mid inhalation and mid exhalation and the lowest MAS tends to be around full exhalation. The breathing periodicity of >0.8 possesses minimal motion artifacts. Conclusion: The 1D-4D correlation provides a fast means to estimate 4DCT image quality. Using 1DRW signal, we can retrospectively screen out high-quality 4DCT images for clinical research (periodicity>0.8) and prospectively identify poor

Integration of human reliability analysis into the probabilistic risk assessment process: phase 1

International Nuclear Information System (INIS)

Bell, B.J.; Vickroy, S.C.

1985-01-01

The US Nuclear Regulatory Commission and Pacific Northwest Laboratory initiated a research program in 1984 to develop a testable set of analytical procedures for integrating human reliability analysis (HRA) into the probabilistic risk assessment (PRA) process to more adequately assess the overall impact of human performance on risk. In this three phase program, stand-alone HRA/PRA analytic procedures will be developed and field evaluated to provide improved methods, techniques, and models for applying quantitative and qualitative human error data which systematically integrate HRA principles, techniques, and analyses throughout the entire PRA process. Phase 1 of the program involved analysis of state-of-the-art PRAs to define the structures and processes currently in use in the industry. Phase 2 research will involve developing a new or revised PRA methodology which will enable more efficient regulation of the industry using quantitative or qualitative results of the PRA. Finally, Phase 3 will be to field test those procedures to assure that the results generated by the new methodologies will be usable and acceptable to the NRC. This paper briefly describes the first phase of the program and outlines the second

Tuning the self-assembled 1,3:2,4-di(3,4-dimethylbenzylidene) sorbitol nanoarchitectures using the phase inversion method

Science.gov (United States)

Lai, Wei-Chi; Tseng, Shen-Jhen

2013-11-01

1,3:2,4-Di(3,4-dimethylbenzylidene) sorbitol (DMDBS) molecules can self-assemble into nanoscaled structures in organic solvents and polymer melts. The nanofibril structures were the mostly found. In this study, we used two phase inversion methods, i.e., dry and wet methods, to obtain different DMDBS nanoarchitectures. Poly(vinylidene fluoride) (PVDF) was chosen as polymer matrix, and the DMDBS structures were tuned by the process of PVDF membrane formation (crystallization and liquid-liquid demixing). When the membrane was prepared using the dry method, the DMDBS structure is controlled by the PVDF crystallization. Fewer DMDBS nanofibrils formed on the surfaces, and no nanofibrils were found in the cross-sections. On the other hand, when the membrane was prepared using the wet method, the liquid-liquid demixing (nonsolvent induced phase separation) occurred simultaneously as PVDF crystallized, and thus influenced the aggregation of DMDBS molecules. DMDBS is an amphiphilic molecule with two hydrophilic hydroxyl groups. The addition of nonsolvent (water) caused a large number of DMDBS molecules to aggregate outside the hydrophobic PVDF. In addition, a new structure "nanomat" was found. The mat was composed of DMDBS nanofibrils with diameters of 10-20 nm, similar to those observed in the dry method membranes. Fourier transform infra-red spectroscopy indicates that the DMDBS molecules self-assembled (aggregated) mainly through intermolecular hydrogen bonding in the presence of PVDF. The more intermolecular hydrogen bonding between DMDBS existed, the more excessive amounts of DMDBS molecules were, leading to the formation of nanomats.

Tank waste remediation system retrieval and disposal mission - Phase 1: Financial analysis

International Nuclear Information System (INIS)

Bickford, J.C.

1998-01-01

In Section 1.0, an overview of the Financial Analysis was provided and summarized in Table 1 for both the Retrieval and Disposal program and the TWRS project life cycle. A table recaps the pre-Phase 1B analysis budget requirements as discussed in previous sections. Another table in this section shows a similar build-up of costs and the impact of proposed offsets and increases to the pre-Phase 1B analysis. The issues concerning the increased requirements in FY 1998/1999 and the recommended adjustments were discussed. The Phase 1B Program as recommended is achievable. Specific recommendations are as follows: (a) Adopt the revised project baseline as presented in the cited tables; (b) Incorporate the $248.5 million in allowances for risk into the baseline; (c) Develop detailed action plans to realize the costs reduction opportunities; (d) Incorporate site indirect and benefits reduction rates into baseline; (e) Delay non-critical path scope which can be moved beyond FY 1999, as indicated: and (f) Renegotiate the Tri-Party Agreement milestones associated with the current compliance unfunded list for FY 1998

NEPHELINE FORMATION STUDY FOR SLUDGE BATCH 4: PHASE 3 EXPERIMENTAL RESULTS

International Nuclear Information System (INIS)

Fox, K

2006-01-01

This Phase 3 study was undertaken to complement the previous phases of the nepheline formation studies1, 2 by continuing the investigation into the ability of the nepheline discriminator to predict the occurrence of nepheline crystallization in Sludge Batch 4 (SB4) glasses and into the impact of such phases on the durability of the SB4 glasses. The Phase 3 study had two primary objectives. The first was to continue to demonstrate the ability of the discriminator value to adequately predict the nepheline formation potential for specific glass systems of interest. The second was to generate additional data that have a high probability of supporting the SB4 variability study. To support these two objectives, sixteen glasses were selected based on the most recent SB4 compositional projection, Case 15C Blend 1.3 Four different frits were included, based on previous assessments of projected operating windows and melt rate,4, 5 with four WLs selected for each frit. Eight of these frit-sludge combinations covered WLs which tightly bound the nepheline discriminator value of 0.62, with the intent of refining this value to a level of confidence where it can be incorporated into offline administrative controls and/or the Process Composition Control System (PCCS) to support Slurry Mix Evaporator (SME) acceptability decisions. The remaining eight frit-sludge combinations targeted lower WLs (35 and 40%) and were prepared and analyzed to contribute needed data to the ComPro database6 to support a potential variability study for SB4

Phase formation kinetics, hardness and magnetocaloric effect of sub-rapidly solidified LaFe11.6Si1.4 plates during isothermal annealing

Science.gov (United States)

Dai, Yuting; Xu, Zhishuai; Luo, Zhiping; Han, Ke; Zhai, Qijie; Zheng, Hongxing

2018-05-01

High-temperature phase transition behavior and intrinsic brittleness of NaZn13-type τ1 phase in La-Fe-Si magnetocaloric materials are two key problems from the viewpoint of materials production and practical applications. In the present work, the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation was introduced to quantitatively characterize the formation kinetics of τ1 phase in sub-rapidly solidified LaFe11.6Si1.4 plates during the isothermal annealing process. Avrami index was estimated to be 0.43 (∼0.5), which suggests that the formation of τ1 phase is in a diffusion-controlled one-dimensional growth mode. Meanwhile, it is found that the Vickers hardness as a function of annealing time for sub-rapidly solidified plates also agrees well with the JMAK equation. The Vickers hardness of τ1 phase was estimated to be about 754. Under a magnetic field change of 30 kOe, the maximum magnetic entropy change was about 22.31 J/(kg·K) for plates annealed at 1323 K for 48 h, and the effective magnetic refrigeration capacity reached 191 J/kg.

Ocean Margins Programs, Phase I research summaries

Energy Technology Data Exchange (ETDEWEB)

Verity, P. [ed.

1994-08-01

During FY 1992, the DOE restructured its regional coastal-ocean programs into a new Ocean Margins Program (OMP), to: Quantify the ecological and biogeochemical processes and mechanisms that affect the cycling, flux, and storage of carbon and other biogenic elements at the land/ocean interface; Define ocean-margin sources and sinks in global biogeochemical cycles, and; Determine whether continental shelves are quantitatively significant in removing carbon dioxide from the atmosphere and isolating it via burial in sediments or export to the interior ocean. Currently, the DOE Ocean Margins Program supports more than 70 principal and co-principal investigators, spanning more than 30 academic institutions. Research funded by the OMP amounted to about $6.9M in FY 1994. This document is a collection of abstracts summarizing the component projects of Phase I of the OMP. This phase included both research and technology development, and comprised projects of both two and three years duration. The attached abstracts describe the goals, methods, measurement scales, strengths and limitations, and status of each project, and level of support. Keywords are provided to index the various projects. The names, addresses, affiliations, and major areas of expertise of the investigators are provided in appendices.

A non-typical sequence of phase transitions in (NH4)3GeF7: optical and structural characterization.

Science.gov (United States)

Mel'nikova, S V; Molokeev, M S; Laptash, N M; Misyul, S V

2016-03-28

Single crystals of germanium double salt (NH4)3GeF7 = (NH4)2GeF6·NH4F = (NH4)3[GeF6]F were grown and studied by the methods of polarization optics and X-ray diffraction. The birefringence Δn = (no - ne), the rotation angle of the optical indicatrix ϕ(T) and unit cell parameters were measured in the temperature range 100-400 K. Three structural phase transitions were found at the temperatures: T1↓ = 279.2 K (T1↑ = 279.4 K), T2↑ = 270 K (T2↓ = 268.9 K), T3↓ = 218 K (T3↑ = 227 K). An unusual sequence of symmetry transformations with temperature change was established: P4/mbm (Z = 2) (G1) ↔ Pbam (Z = 4) (G2) ↔ P21/c (Z = 4) (G3) ↔ Pa3[combining macron] (Z = 8) (G4). The crystal structures of different phases were determined. The experimental data were additionally interpreted by a group-theoretical analysis of the complete condensate of order parameters taking into account the critical and noncritical atomic displacements. Strengthening of the N-HF hydrogen bonds can be a driving force of the observed phase transitions.

Detection of high PD-L1 expression in oral cancers by a novel monoclonal antibody L1Mab-4

Directory of Open Access Journals (Sweden)

Shinji Yamada

2018-03-01

Full Text Available Programmed cell death-ligand 1 (PD-L1, which is a ligand of programmed cell death-1 (PD-1, is a type I transmembrane glycoprotein that is expressed on antigen-presenting cells and several tumor cells, including melanoma and lung cancer cells. There is a strong correlation between human PD-L1 (hPD-L1 expression on tumor cells and negative prognosis in cancer patients. In this study, we produced a novel anti-hPD-L1 monoclonal antibody (mAb, L1Mab-4 (IgG2b, kappa, using cell-based immunization and screening (CBIS method and investigated hPD-L1 expression in oral cancers. L1Mab-4 reacted with oral cancer cell lines (Ca9-22, HO-1-u-1, SAS, HSC-2, HSC-3, and HSC-4 in flow cytometry and stained oral cancers in a membrane-staining pattern. L1Mab-4 stained 106/150 (70.7% of oral squamous cell carcinomas, indicating the very high sensitivity of L1Mab-4. These results indicate that L1Mab-4 could be useful for investigating the function of hPD-L1 in oral cancers. Keywords: Programmed cell death-ligand 1, Monoclonal antibody, Oral cancer

THE ROLE OF 4-HYDROXYPHENYLPYRUVATE DIOXYGENASE IN ENHANCEMENT OF SOLID-PHASE ELECTRON TRANSFER BY SHEWANELLA ONEIDENSIS MR-1

Energy Technology Data Exchange (ETDEWEB)

Turick, C; Amy Ekechukwu, A

2007-06-01

While mechanistic details of dissimilatory metal reduction are far from being understood, it is postulated that the electron transfer to solid metal oxides is mediated by outer membrane-associated c-type cytochromes and redox active electron shuttling compounds. This study focuses on the production of homogensitate in Shewanella oneidensis MR-1, an intermediate of tyrosine degradation pathway, which is a precursor of a redox cycling metabolite, pyomelanin. In this study, we determined that two enzymes involved in this pathway, 4-hydroxyphenylpyruvate dioxygenase (4HPPD) and homogentisate 1,2-dioxygenase are responsible for homogentisate production and oxidation, respectively. Inhibition of 4-HPPD activity with the specific inhibitor sulcotrione (2-(2-chloro-4-methane sulfonylbenzoyl)-1,3-cyclohexanedione), and deletion of melA, a gene encoding 4-HPPD, resulted in no pyomelanin production by S. oneidensis MR-1. Conversely, deletion of hmgA which encodes the putative homogentisate 1,2-dioxygenase, resulted in pyomelanin overproduction. The efficiency and rates, with which MR-1 reduces hydrous ferric oxide, were directly linked to the ability of mutant strains to produce pyomelanin. Electrochemical studies with whole cells demonstrated that pyomelanin substantially increases the formal potential (E{sup o}{prime}) of S. oneidensis MR-1. Based on this work, environmental production of pyomelanin likely contributes to an increased solid-phase metal reduction capacity in Shewanella oneidensis.

Phase evolution and photoluminescence enhancement of CePO4 nanowires from a low phosphate concentration system

International Nuclear Information System (INIS)

Xu Pengfei; Yu Ranbo; Zong Lingbo; Wang Jiali; Wang Dan; Deng Jinxia; Chen Jun; Xing Xianran

2013-01-01

Uniform CePO 4 nanowires have been successfully synthesized in a low phosphate concentration system through a single-step hydrothermal process. The low phosphate concentration might decrease the surface PO 4 3− adsorption of the as-synthesized CePO 4 nanowires efficiently and benefit their photoluminescence. The CePO 4 nanowires were identified to go through phase evolution from pure monoclinic to mixed hexagonal and monoclinic phase by only increasing the initial molar ratio of cerium and phosphate source (denoted as Ce/P). Interestingly, the strongest photoluminescence was observed in the CePO 4 nanowires synthesized with the initial Ce/P of 4:1, which proved to be the critical phase evolution point between the hexagonal and monoclinic CePO 4 . Therefore, the strong photoluminescence could be explained by the existence of the structure-sensitive energy level in the CePO 4 . This kind of photoluminescence enhancement would be a meaningful reference for design of other photoluminescent materials, in which the photoluminescent emission might be related to the structure-sensitive energy level. Additionally, the growth processes of CePO 4 nanowires based on related well-designed experiments were proposed.

High Pressure Differential Scanning Calorimetry of poly(4-methyl-pentene-1)

NARCIS (Netherlands)

Hoehne, G.W.H.; Rastogi, S.; Wunderlich, B.

2000-01-01

The polymer poly(4-methyl pentene-1), P4MP1, displays an unusual pressure–temperature phase diagram. The previous exploration of this phase behavior through X-ray diffraction has been extended through high-pressure calorimetry. The resulting phase diagram displays a melt area, the common tetragonal

A new high-pressure phase of Fe2SiO4 and the relationship between spin and structural transitions

Science.gov (United States)

Yamanaka, T.; Kyono, A.; Nakamoto, Y.; Kharlamova, S. A.; Struzhkin, V. V.; Gramsch, S.; Mao, H.; Hemley, R. J.

2013-12-01

O4. This new high-pressure phase reversibly transforms to the spinel structure under decompression. A Martensitic transformation of spinel slabs with translation vector [1/8 1/8 1/8] generates the I-Fe2SiO4 structure. The transition is induced by atomic displacements in the spinel structure, which generates the orthorhombic distortion resulting in I-Fe2SiO4 arrangement. A topotactic relation between spinel and I-Fe2SiO4 is suggested as the origin of this phase transition: Fe2SiO4 spinel at 34.8 GPa, Fd m, z = 8, a(spinel)= 7.894 Å I-Fe2SiO4 at 54.6 GPa, Imma,, z = 4, a= 5.543(1)Å, b=6.032(4)Å, c= 7.201(5)Å a = b = d(spnel 110) = 0.707107a (spinel) c= c(spinel) Compression along the [001] direction of the spinel structure and simultaneous elongation along the [110] direction results in the I-Fe2SiO4 arrangement. This transition is induced by the 20% shrinkage of ionic radius of Fe2+in the octahedral site at the low spin state.

EGS4 benchmark program

International Nuclear Information System (INIS)

Yasu, Y.; Hirayama, H.; Namito, Y.; Yashiro, S.

1995-01-01

This paper proposes EGS4 Benchmark Suite which consists of three programs called UCSAMPL4, UCSAMPL4I and XYZDOS. This paper also evaluates optimization methods of recent RISC/UNIX systems, such as IBM, HP, DEC, Hitachi and Fujitsu, for the benchmark suite. When particular compiler option and math library were included in the evaluation process, system performed significantly better. Observed performance of some of the RISC/UNIX systems were beyond some so-called Mainframes of IBM, Hitachi or Fujitsu. The computer performance of EGS4 Code System on an HP9000/735 (99MHz) was defined to be the unit of EGS4 Unit. The EGS4 Benchmark Suite also run on various PCs such as Pentiums, i486 and DEC alpha and so forth. The performance of recent fast PCs reaches that of recent RISC/UNIX systems. The benchmark programs have been evaluated with correlation of industry benchmark programs, namely, SPECmark. (author)

40 CFR 76.8 - Early election for Group 1, Phase II boilers.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Early election for Group 1, Phase II boilers. 76.8 Section 76.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.8 Early election for Group 1...

Thermodynamic properties of 1-ethyl-4-nitro-1,2,3-triazole

Energy Technology Data Exchange (ETDEWEB)

Blokhin, Andrey V., E-mail: blokhin@bsu.by; Kohut, Sviataslau V.; Kabo, Gennady J.; Stepurko, Elena N.; Paulechka, Yauheni U.; Voitkevich, Olga V.

2013-08-10

Graphical abstract: - Highlights: • Heat capacities and phase transition enthalpies for 1-ethyl-4-nitro-1,2,3-triazole were measured. • Enthalpy of formation for 1-ethyl-4-nitro-1,2,3-triazole was determined. • Vapor pressure and enthalpy of sublimation of 1-ethyl-4-nitro-1,2,3-triazole were found from Knudsen measurements. - Abstract: Temperature dependence of the heat capacity and the parameters of phase transitions of 1-ethyl-4-nitro-1,2,3-triazole (1ET) were studied between 5 and 370 K in a vacuum adiabatic calorimeter. Thermodynamic properties of the 1ET in the condensed state were obtained over the range of 0–370 K. Saturated vapor pressure for crystalline 1ET in the temperature ranges from 313 to 344 K and its enthalpy of sublimation were measured by the Knudsen effusion method. The standard enthalpy of formation for crystalline 1ET at 298.15 K was determined in a static bomb combustion calorimeter. From these data, the standard enthalpy of formation for gaseous 1ET was evaluated. The enthalpy of formation calculated using quantum chemical methods is in excellent agreement with the experimental value.

Thermodynamic properties of 1-ethyl-4-nitro-1,2,3-triazole

International Nuclear Information System (INIS)

Blokhin, Andrey V.; Kohut, Sviataslau V.; Kabo, Gennady J.; Stepurko, Elena N.; Paulechka, Yauheni U.; Voitkevich, Olga V.

2013-01-01

Graphical abstract: - Highlights: • Heat capacities and phase transition enthalpies for 1-ethyl-4-nitro-1,2,3-triazole were measured. • Enthalpy of formation for 1-ethyl-4-nitro-1,2,3-triazole was determined. • Vapor pressure and enthalpy of sublimation of 1-ethyl-4-nitro-1,2,3-triazole were found from Knudsen measurements. - Abstract: Temperature dependence of the heat capacity and the parameters of phase transitions of 1-ethyl-4-nitro-1,2,3-triazole (1ET) were studied between 5 and 370 K in a vacuum adiabatic calorimeter. Thermodynamic properties of the 1ET in the condensed state were obtained over the range of 0–370 K. Saturated vapor pressure for crystalline 1ET in the temperature ranges from 313 to 344 K and its enthalpy of sublimation were measured by the Knudsen effusion method. The standard enthalpy of formation for crystalline 1ET at 298.15 K was determined in a static bomb combustion calorimeter. From these data, the standard enthalpy of formation for gaseous 1ET was evaluated. The enthalpy of formation calculated using quantum chemical methods is in excellent agreement with the experimental value

Ku to V-band 4-bit MEMS phase shifter bank using high isolation SP4T switches and DMTL structures

Science.gov (United States)

Dey, Sukomal; Koul, Shiban K.; Poddar, Ajay K.; Rohde, Ulrich L.

2017-10-01

This work presents a micro-electro-mechanical system (MEMS) based on a wide-band 4-bit phase shifter using two back-to-back single-pole-four-throw (SP4T) switches and four different distributed MEMS transmission line (DMTL) structures that are implemented on 635 µm alumina substrate using surface micromachining process. An SP4T switch is designed with a series-shunt configuration and it demonstrates an average return loss of  >17 dB, an insertion loss of  28 dB up to 60 GHz. A maximum area of the SP4T switch is ~0.76 mm2. Single-pole-single-throw and SP4T switches are capable of handling 1 W of radio frequency (RF) power up to  >100 million cycles at 25° C; they can even sustained up to  >70 million cycles with 1 W at 85 °C. The proposed wide-band phase shifter works at 17 GHz (Ku-band), 25 GHz (K-band), 35 GHz (Ka-band) and 60 GHz (V-band) frequencies. Finally,a 4-bit phase shifter demonstrates an average insertion loss of  10 dB and maximum phase error of ~3.8° at 60 GHz frequency over 500 MHz bandwidth. Total area of the fabricated device is ~11 mm2. In addition, the proposed device works well up to  >107 cycles with 1 W of RF power. To the best of the author’s knowledge, this is the best reported wide-band MEMS 4-bit phase shifter in the literature that works with a constant resolution.

Seismic Safety Margins Research Program: Phase II program plan (FY 83-FY 84)

International Nuclear Information System (INIS)

Bohn, M.P.; Bernreuter, D.L.; Cover, L.E.; Johnson, J.J.; Shieh, L.C.; Shukla, S.N.; Wells, J.E.

1982-01-01

The Seismic Safety Margins Research Program (SSMRP) is an NRC-funded, multiyear program conducted by Lawrence Livermore National Laboratory (LLNL). Its goal is to develop a complete, fully coupled analysis procedure (including methods and computer codes) for estimating the risk of an earthquake-caused radioactive release from a commercial nuclear power plant. The analysis procedure is based upon a state-of-the-art evaluation of the current seismic analysis and design process and explicitly includes the uncertainties inherent in such a process. The results will be used to improve seismic licensing requirements for nuclear power plants. As currently planned, the SSMRP will be completed in September, 1984. This document presents the program plan for work to be done during the remainder of the program. In Phase I of the SSMRP, the necessary tools (both computer codes and data bases) for performing a detailed seismic risk analysis were identified and developed. Demonstration calculations were performed on the Zion Nuclear Power Plant. In the remainder of the program (Phase II) work will be concentrated on developing a simplified SSMRP methodology for routine probabilistic risk assessments, quantitative validation of the tools developed and application of the simplified methodology to a Boiling Water Reactor. (The Zion plant is a pressurized water reactor.) In addition, considerable effort will be devoted to making the codes and data bases easily accessible to the public

Reliability and safety program plan outline for the operational phase of a waste isolation facility

International Nuclear Information System (INIS)

Ammer, H.G.; Wood, D.E.

1977-01-01

A Reliability and Safety Program plan outline has been prepared for the operational phase of a Waste Isolation Facility. The program includes major functions of risk assessment, technical support activities, quality assurance, operational safety, configuration monitoring, reliability analysis and support and coordination meetings. Detailed activity or task descriptions are included for each function. Activities are time-phased and presented in the PERT format for scheduling and interactions. Task descriptions include manloading, travel, and computer time estimates to provide data for future costing. The program outlined here will be used to provide guidance from a reliability and safety standpoint to design, procurement, construction, and operation of repositories for nuclear waste. These repositories are to be constructed under the National Waste Terminal Storage program under the direction of the Office of Waste Isolation, Union Carbide Corp. Nuclear Division

Evaluation of the Tier 1 Program of Project P.A.T.H.S.: Secondary Data Analyses of Conclusions Drawn by the Program Implementers

Directory of Open Access Journals (Sweden)

Daniel T. L. Shek

2008-01-01

Full Text Available The Tier 1 Program of the Project P.A.T.H.S. (Positive Adolescent Training through Holistic Social Programmes is a curricula-based positive youth development program. In the experimental implementation phase, 52 schools participated in the program. Based on subjective outcome evaluation data collected from the program participants (Form A and program implementers (Form B in each school, the program implementers were invited to write down five conclusions based on an integration of the evaluation findings (N = 52. The conclusions stated in the 52 evaluation reports were further analyzed via secondary data analyses in this paper. Results showed that most of the conclusions concerning perceptions of the Tier 1 Program, instructors, and effectiveness of the programs were positive in nature. There were also conclusions reflecting the respondents’ appreciation of the program. Finally, responses on the difficulties encountered and suggestions for improvements were observed. In conjunction with the previous evaluation findings, the present study suggests that the Tier 1 Program was well received by the stakeholders and the program was beneficial to the development of the program participants.

An Overview of 2014 SBIR Phase 1 and Phase 2 Communications Technology and Development

Science.gov (United States)

Nguyen, Hung D.; Steele, Gynelle C.; Morris, Jessica R.

2015-01-01

NASA's Small Business Innovation Research (SBIR) program focuses on technological innovation by investing in development of innovative concepts and technologies to help NASA mission directorates address critical research needs for Agency programs. This report highlights eight of the innovative SBIR 2014 Phase I and Phase II projects that emphasize one of NASA Glenn Research Center's six core competencies-Communication Technology and Development. The technologies cover a wide spectrum of applications such as X-ray navigation, microsensor instrument for unmanned aerial vehicle airborne atmospheric measurements, 16-element graphene-based phased array antenna system, interferometric star tracker, ultralow power fast-response sensor, and integrated spacecraft navigation and communication. Each featured technology describes an innovation, technical objective, and highlights NASA commercial and industrial applications. This report provides an opportunity for NASA engineers, researchers, and program managers to learn how NASA SBIR technologies could help their programs and projects, and lead to collaborations and partnerships between the small SBIR companies and NASA that would benefit both.

Investigation of properties and performance of ceramic composite components: Final report on Phases 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Curtin, W.A.; Halverson, H.; Carter, R.H.; Miraj, N.; Reifsnider, K.L. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States)

1998-01-15

The objective of the Fossil Energy Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for longer-term fossil energy applications as well as for generic needs of various fossil fuel technologies. The research program of the Materials Response Group at Virginia Tech addresses the need for reliable and durable structural ceramic composites to perform in high temperature environments. The research effort provides an experimental and analytical basis for the transition from properties of materials to performance of actual component structures. Phases 1 and 2 of the present program focused on the development of test capabilities, initial studies of component mechanical response under various conditions and the development of a life prediction methodology. These efforts have been described in previous reports. This report summarizes the major tasks completed under Phases 3 and 4 of the project. Overall, the authors have made significant progress in a broad spectrum of tasks in this program. Their efforts have encompassed component evaluation, assessment of new SiC-based composites with improved high-temperature potential, development of oxide coating materials for SiC, and the extension and development of new models for predicting the durability of composite components under specific operating conditions for various CMC applications. Each of these areas of work is an important area for achieving the ultimate goal of usable SiC-based composites in high-temperature corrosive environments typical of fossil energy applications.

Compact Monitor for Airborne Carbon Dioxide Measurements, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Eltron Research we anticipate a TRL of 4 by the end of Phase I. By the end of the Phase II program, a prototype instrument will be built with ±0.1 ppm resolution in...

Cell cycle phase dependent emergence of thymidylate synthase studied by monoclonal antibody (M-TS-4).

Science.gov (United States)

Shibui, S; Hoshino, T; Iwasaki, K; Nomura, K; Jastreboff, M M

1989-05-01

A method of identifying thymidylate synthase (TS) at the cellular level was developed using anti-TS monoclonal antibody (M-TS-4), a monoclonal antibody created against purified TS from a HeLa cell line. In HeLa cells and four human glioma cell lines (U-251, U-87, 343-MGA, and SF-188), TS was identified primarily in the cytoplasm. Autoradiographic and flow cytometric studies showed that TS appeared mainly in the G1 phase and subsided early in the S phase; thus, the G1 phase can be divided into TS-positive and -negative fractions. Nuclear TS was not demonstrated unequivocally with M-TS-4, and the relationship between nuclear TS and DNA synthesis could not be determined. Although the percentage of TS-positive cells was larger than the S-phase fraction measured by autoradiography after a pulse of tritiated thymidine or by the immunoperoxidase method using BUdR, the ratios were within a similar range (1.2-1.4) in all cell lines studied. Therefore, the S-phase fraction can be estimated indirectly from the percentage of TS-positive cells measured by M-TS-4. Because the emergence of TS detected by our method is cell cycle dependent, M-TS-4 may be useful for biochemical studies of TS and for cytokinetic analysis.

Basic hydrolysis of 1, 3, 4, 6-tetra-O-acetyl-2-[18F] fluoro-D-glucose on solid phase extraction

International Nuclear Information System (INIS)

Zhang Jinming; Tian Jiahe; He Yijie; Huan Dingcai; Liu Boli

2003-01-01

A new base hydrolysis method are used for 1, 3, 4, 6-tetra-O-acetyl-2-[ 18 F] fluoro-D-glucose on solid phase extraction. The labeled intermediate is trapped on an active C-18 solid phase extraction cartridge, and hydrolyzed in cartridge with 1 mL 2 mol/L NaOH at room temperature. The results show that there are over 99% of the labeled intermediate being turned into 18 F-FDG within 2 min. It is easy to get 18 F-FDG after neutralized with phosphate buffer, purified by C-18 and Alumina cartridge. The basic hydrolysis on solid extraction is a simple method for preparation of 18 F-FDG

26 CFR 1.50B-4 - Partnerships.

Science.gov (United States)

2010-04-01

... § 1.50A-3, or if the partnership fails to pay comparable wages and such failure is subject to the... 26 Internal Revenue 1 2010-04-01 2010-04-01 true Partnerships. 1.50B-4 Section 1.50B-4 Internal... Credit for Expenses of Work Incentive Programs § 1.50B-4 Partnerships. (a) General rule—(1) In general...

US/French Joint Research Program regarding the behavior of polymer base materials subjected to beta radiation. Volume 1. Phase-1 normalization results

International Nuclear Information System (INIS)

Wyant, F.J.; Buckalew, W.H.; Chenion, J.; Carlin, F.; Gaussens, G.; Le Tutour, P.; Le Meur, M.

1986-06-01

As part of the ongoing multi-year joint NRC/CEA international cooperative test program to investigate the dose-damage equivalence of gamma and beta radiation on polymer base materials, dosimetry and ethylene-propylene rubber (EPR) specimens were exchanged, irradiated, and evaluated for property changes at research facilities in the US (Sandia National Laboratories) and France (Compagnie ORIS Industrie). The purpose of this Phase-1 test series was to normalize and cross-correlate the results obtained by one research center to the other, in terms of exposure (1.0 MeV accelerated electrons and 60 Co gammas) and postirradiation testing (ultimate elongation and tensile strength, hardness, and density) techniques. The dosimetry and material specimen results indicate good agreement between the two countries regarding the exposure conditions and postirradiation evaluation techniques employed

Defense Small Business Innovation Research Program (SBIR) Volume 2. Navy Abstracts of Phase 1 Awards, 1987

Science.gov (United States)

1988-04-01

LOSS OF POWER TO THE COMPRESSOR SYS- TEM. COMPLETE EFFICIENCY OF THIS DEHYDRATOR WILL RESUME WITHIN A FEW SECONDS FOLLOWING RESTORATION OF POWER...NAVY SUBMITTED BY THIS PHASE I PROGRAM IS DIRECTED TOWARD THE DEVELOPMENT OF A CHARGE- ENHANCED MICROFILTRATION MEMBRANE SYSTEM FOR REMOVAL OF SUSPENDED...THAT A SINGLE 10V " RESTORE " PULSE RETURNS THE KNO(3) MEMORIES TO A STATE VERY NEAR THAT OF VIRGIN DEVICES. RE- LATED ELECTRICAL REMEDIES FOR FATIGUE

Fourier transform infrared study of the phase transitions in (NH4)3VO2FO4

Science.gov (United States)

de Waal, D.; Heyns, A. M.

1994-01-01

Ammonium oxofluorovanadate compounds are known to show some potential as ferroelectric materials. The whole series of ammonium and sodium oxofluorovanadate compounds including Na3VO2F4 have already been prepared and investigated by means of various techniques including x-ray diffraction, EPR, and vibrational spectroscopy. It was established that the pure ammonium compound shows the two above mentioned transitions from phase A (below 200 K) to phase B (between 200 and 400 K) and phase C (above 400 K) while Na(NH4)2VO2F4 has only one transition from phase A to phase B around 400 K4. In the present study various aspects regarding the nature of the structures of (NH4)3VO2F3 and Na(NH4)2VO2F4 and its influence on the phase transitions have been investigated.

Quantum phase transition in the U(4) vibron model and the E(3) symmetry

International Nuclear Information System (INIS)

Zhang Yu; Hou Zhanfeng; Chen Huan; Wei Haiqing; Liu Yuxin

2008-01-01

We study the details of the U(3)-O(4) quantum phase transition in the U(4) vibron model. Both asymptotic analysis in the classical limit and rigorous calculations for finite boson number systems indicate that a second-order phase transition is still there even for the systems with boson number N ranging from tens to hundreds. Two kinds of effective order parameters, including E1 transition ratios B(E1:2 1 →1 1 )/B(E1:1 1 →0 1 ) and B(E1:0 2 →1 1 )/B(E1:1 1 →0 1 ), and the energy ratios E 2 1 /E 0 2 and E 3 1 /E 0 2 are proposed to identify the second-order phase transition in experiments. We also found that the critical point of phase transition can be approximately described by the E(3) symmetry, which persists even for moderate N∼10 protected by the scaling behaviors of quantities at the critical point. In addition, a possible empirical example exhibiting roughly the E(3) symmetry is discussed

"Optics 4 every1", the hands-on optics outreach program of the Universidad Autonoma de Nuevo Leon

Science.gov (United States)

Viera-González, Perla M.; Sánchez-Guerrero, Guillermo E.

2016-09-01

The Fisica Pato2 (Physics 4 every1) outreach group started as a need of hands-on activities and active Science demonstrations in the education for kids, teenagers and basic education teachers in Nuevo Leffon maintaining a main objective of spread the word about the importance of Optics and Photonics; for accomplish this objective, since November 2013 several outreach events are organized every year by the group. The program Optics 4 every1 is supported by the Facultad de Ciencias Fisico Matematicas of the Universidad Autonoma de Nuevo Leon and the International Society for Optics and Photonics and consist in quick hands-on activities and Optics demonstrations designed for teach basic optical phenomena related with light and its application in everyday life. During 2015, with the purpose of celebrate the International Year of Light 2015, the outreach group was involved in 13 different events and reached more than 8,000 people. The present work explains the activities done and the outcome obtained with this program.

Lattice parameters values and phase diagram for the Cu{sub 2}Zn{sub 1−z}Mn{sub z}GeSe{sub 4} alloy system

Energy Technology Data Exchange (ETDEWEB)

Caldera, D. [Centro de Estudios de Semiconductores, Departamento de Física, Facultad de Ciencias, Universidad de Los Andes, Mérida 5101 (Venezuela, Bolivarian Republic of); Quintero, M., E-mail: mquinter@ula.ve [Centro de Estudios de Semiconductores, Departamento de Física, Facultad de Ciencias, Universidad de Los Andes, Mérida 5101 (Venezuela, Bolivarian Republic of); Morocoima, M.; Moreno, E.; Quintero, E.; Grima-Gallardo, P.; Bocaranda, P. [Centro de Estudios de Semiconductores, Departamento de Física, Facultad de Ciencias, Universidad de Los Andes, Mérida 5101 (Venezuela, Bolivarian Republic of); Henao, J.A.; Macías, M.A. [Grupo de Investigación en Química Estructural (GIQUE), Facultad de Ciencias, Escuela de Química, Universidad Industrial de Santander, Apartado aéreo 678, Bucaramanga (Colombia); Briceño, J.M.; Mora, A.E. [Laboratorio de Análisis Químico y Estructura de Materiales, Departamento de Física, Universidad de Los Andes, Mérida 5101 (Venezuela, Bolivarian Republic of)

2014-11-25

Highlights: • The samples were annealed at 500 °C for 1 month. • Samples in the ranges 0 < z < 0.375 had the tetragonal stannite α structure (I4{sup ¯}2m). • For 0.725 < z ⩽ 1 the wurtz–stannite δ structure (Pmn2{sub 1}). • Undercooling effects occur for samples in the range 0.725 < z < 0.925. - Abstract: The T(z) phase diagram of the Cu{sub 2}Zn{sub 1−z}Mn{sub z}GeSe{sub 4} alloy system is obtained from X-ray diffraction and differential thermal analysis DTA. At room temperature, the X-ray diffraction data showed that samples in the ranges 0 < z < 0.375 had the tetragonal stannite α structure (I4{sup ¯}2m), while for 0.725 < z ⩽ 1 the wurtz–stannite δ structure (Pmn2{sub 1}). The α and δ fields are separated by a relative wide three-phase field (α + δ + MnSe{sub 2}). The DTA thermograms were used to construct the phase diagram of the Cu{sub 2}Zn{sub 1−z}Mn{sub z}GeSe{sub 4} alloy system. It was confirmed that the Cu{sub 2}ZnGeSe{sub 4} and Cu{sub 2}MnGeSe{sub 4} compounds melt incongruently. It was observed that undercooling effects occur for samples in the range 0.725 < z < 0.925.

Psi4 1.1: An Open-Source Electronic Structure Program Emphasizing Automation, Advanced Libraries, and Interoperability.

Science.gov (United States)

Parrish, Robert M; Burns, Lori A; Smith, Daniel G A; Simmonett, Andrew C; DePrince, A Eugene; Hohenstein, Edward G; Bozkaya, Uğur; Sokolov, Alexander Yu; Di Remigio, Roberto; Richard, Ryan M; Gonthier, Jérôme F; James, Andrew M; McAlexander, Harley R; Kumar, Ashutosh; Saitow, Masaaki; Wang, Xiao; Pritchard, Benjamin P; Verma, Prakash; Schaefer, Henry F; Patkowski, Konrad; King, Rollin A; Valeev, Edward F; Evangelista, Francesco A; Turney, Justin M; Crawford, T Daniel; Sherrill, C David

2017-07-11

Psi4 is an ab initio electronic structure program providing methods such as Hartree-Fock, density functional theory, configuration interaction, and coupled-cluster theory. The 1.1 release represents a major update meant to automate complex tasks, such as geometry optimization using complete-basis-set extrapolation or focal-point methods. Conversion of the top-level code to a Python module means that Psi4 can now be used in complex workflows alongside other Python tools. Several new features have been added with the aid of libraries providing easy access to techniques such as density fitting, Cholesky decomposition, and Laplace denominators. The build system has been completely rewritten to simplify interoperability with independent, reusable software components for quantum chemistry. Finally, a wide range of new theoretical methods and analyses have been added to the code base, including functional-group and open-shell symmetry adapted perturbation theory, density-fitted coupled cluster with frozen natural orbitals, orbital-optimized perturbation and coupled-cluster methods (e.g., OO-MP2 and OO-LCCD), density-fitted multiconfigurational self-consistent field, density cumulant functional theory, algebraic-diagrammatic construction excited states, improvements to the geometry optimizer, and the "X2C" approach to relativistic corrections, among many other improvements.

Army Enlisted Personnel Competency Assessment Program Phase 1. Volume 1: Needs Analysis

National Research Council Canada - National Science Library

Knapp, Deirdre

2004-01-01

.... The PerformM21 program has two mutually supporting tracks. The first is a needs analysis that will result in design recommendations and identification of issues related to implementation of a competency assessment program...

Density-functional theory study of the pressure-induced phase transition in hydronitrogen compound N{sub 4}H{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Liu, Qi-Jun, E-mail: qijunliu@home.swjtu.edu.cn [Bond and Band Engineering Group, Sichuan Provincial Key Laboratory (for Universities) of High Pressure Science and Technology, School of Physical Science and Technology, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhang, Ning-Chao; Sun, Yan-Yun; Zhang, Ming-Jian; Liu, Fu-Sheng [Bond and Band Engineering Group, Sichuan Provincial Key Laboratory (for Universities) of High Pressure Science and Technology, School of Physical Science and Technology, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Liu, Zheng-Tang [State Key Laboratory of Solidification Processing, School of Materials Science and Engineering, Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China)

2014-03-01

Using first-principles density-functional theory, we have investigated the pressure-induced phase transition in hydronitrogen compound N{sub 4}H{sub 4} and discussed the potential tetragonal structure. We find that tetragonal structure with P4{sub 2}/n space group is mechanically stable and ductile. The thermodynamic stability of Pmna>P1{sup ¯}>P4{sub 2}/n>P2{sub 1}/m has been obtained. With increasing pressure, the phase transition pressures of T{sub Pmna→P4{sub 2/n}}, T{sub P4{sub 2/n→Pmna}}, T{sub Pmna→P1{sup ¯}} and T{sub P1{sup ¯}→P2{sub 1/m}} are 5.6, 15.0, 30.0 and 69.2 GPa, respectively, which are in agreement with the available data. Moreover, the mechanical stability of four structures under pressure has been analyzed.

Feasibility study of $B_s \\rightarrow \\phi \\phi \\rightarrow$ 4K with L1 Tracks at the CMS Phase-II Detector

CERN Document Server

Bhattacharya, Rajarshi

2017-01-01

$B_s \\rightarrow \\phi \\phi \\rightarrow$ 4 Kaons is an important physics process to study during the LHC Phase-II which is expected to start in 2024. In this process, the CP violating weak phase arises due to the CP violation of the $B_s - \\bar{B_s}$ mixing and the gluonic penguin decay of b $\\rightarrow$ s$\\bar s$s. The penguin decay of the b-quark makes it a rare process also. The CMS experiment is planning to include tracker information at Level-1 Trigger to keep event rate manageable in the high luminosity regime of the LHC PhaseII. The aim of the present study is to understand whether CMS will be able to trigger on the $B_s \\rightarrow \\phi \\phi \\rightarrow$ 4 Kaons events and be competitive with LHCb during LHC PhaseII. We shall discuss about signal efficiency and event rate both at the trigger as well as physics analysis levels and also look at several ways of optimization of efficiency and event rate.

Plutonium disposition study phase 1b final report

International Nuclear Information System (INIS)

1993-01-01

This report provides the results of the Westinghouse activities performed as part of the Plutonium Disposition Study Phase 1b. These activities, which took place from May 16, 1993 to September 15, 1993, build upon the work completed in Phase 1a, which concluded on May 15, 1993. In Phase 1a, three Plutonium Disposal Reactor (PDR) options were developed for the disposal of excess weapons grade plutonium from returned and dismantled nuclear weapons. This report documents the results of several tasks that were performed to further knowledge in specific areas leading up to Phase 2 of the PDR Study. The Westinghouse activities for Phase 1b are summarized as follows: (1) resolved technical issues concerning reactor physics including equilibrium cycle calculations, use of gadolinium, moderator temperature coefficient, and others as documented in Section 2.0; (2) analyzed large Westinghouse commercial plants for plutonium disposal; (3) reactor safety issues including the steam line break were resolved, and are included in Section 2.0; (4) several tasks related to the PDR Fuel Cycle were examined; (5) cost and deployment options were examined to determine optimal configuration for both plutonium disposal and tritium production; (6) response to questions from DOE and National Academy of Scientists (NAS) reviewers concerning the PDR Phase 1a report are included in Appendix A

A visual user interface program, EGSWIN, for EGS4

International Nuclear Information System (INIS)

Qiu Rui; Li Junli; Wu Zhen

2005-01-01

To overcome the inconvenience and difficulty in using the EGS4 code by novice users, a visual user interface program, called the EGSWIN system, has been developed by the Monte Carlo Research Center of Tsinghua University in China. EGSWIN allows users to run EGS4 for many applications without any user coding. A mixed-language programming technique with Visual C++ and Visual Fortran is used in order to embed both EGS4 and PEGS4 into EGSWIN. The system has the features of visual geometry input, geometry processing, visual definitions of source, scoring and computing parameters, and particle trajectories display. Comparison between the calculated results with EGS4 and EGSWIN, as well as with FLUKA and GEANT, has been made to validate EGSWIN. (author)

DYNAPO 4 - a fluid system and frames analysis computer program

International Nuclear Information System (INIS)

Lefter, J.D.; Ahdout, H.

1982-01-01

DYNAPO 4 is a user oriented specialized computer program, capable of analyzing three-dimensional linear elastic piping systems or frames for static loads, dynamic loads represented by acceleration response spectra, transient dynamic loads represented by harmonic, polynomial of second order, and time history forcing functions. DYNAPO 4 has plotting capability, which plots the input configuration of the piping system or of the structure and also plots its deformed shape after the load is applied. DYNAPO 4 performs the analysis for ASME Section III Class 1, Class 2, and 3, piping, and provides the user with stress reports as per ASME and ANSI Code requirements. 3 refs

Lattice parameters values and phase diagram for the Cu{sub 2}Zn{sub 1-z}Fe{sub z}GeSe{sub 4} alloy system

Energy Technology Data Exchange (ETDEWEB)

Caldera, D. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Quintero, M. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela)], E-mail: mquinter@ula.ve; Morocoima, M.; Quintero, E.; Grima, P.; Marchan, N.; Moreno, E.; Bocaranda, P. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Delgado, G.E. [Laboratorio de Cristalografia, Departamento de Quimica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Mora, A.E.; Briceno, J.M.; Fernandez, J.L. [Laboratorio de Analisis Quimico y Estructura de Materiales, Departamento de Fisica, Universidad de Los Andes, Merida 5101 (Venezuela)

2008-06-12

X-ray powder diffraction and differential thermal analysis (DTA) measurements were made on polycrystalline samples of the Cu{sub 2}Zn{sub 1-z}Fe{sub z}GeSe{sub 4} alloy system. The diffraction patterns were used to show the equilibrium conditions and to estimate crystalline parameter values. It was found that, at room temperature, a single phase solid solution with the tetragonal stannite {alpha} structure (I4-bar2m) occurs across the whole composition range. The DTA thermograms were used to construct the phase diagram of the Cu{sub 2}Zn{sub 1-z}Fe{sub z}GeSe{sub 4} alloy system. It was confirmed that the Cu{sub 2}ZnGeSe{sub 4} compound melts incongruently. It was observed that undercooling effects occur for samples with z > 0.9.

Low-temperature structural phase transition in synthetic libethenite Cu2PO4OH

International Nuclear Information System (INIS)

Belik, Alexei A.; Naumov, Pance; Kim, Jungeun; Tsuda, Shunsuke

2011-01-01

Low-temperature structural properties of the synthetic mineral libethenite Cu 2 PO 4 OH were investigated by single-crystal X-ray diffraction, synchrotron X-ray powder diffraction, specific heat measurements, and Raman spectroscopy. A second-order structural phase transition from the Pnnm symmetry (a=8.0553(8) A, b=8.3750(9) A, c=5.8818(6) A at 180 K) to the P2 1 /n symmetry (a=8.0545(8) A, b=8.3622(9) A, c=5.8755(6) A, β=90.0012(15) at 120 K) was found at 160 K during cooling. At 120 K, the monoclinic angle is 90.0012(15) from single crystal X-ray data vs 90.083(1) from powder X-ray diffraction data. The P2 1 /n-to-Pnnm transition may be a general feature of the adamite-type compounds, M 2 XO 4 OH. - Graphical Abstract: Fragments of experimental synchrotron X-ray powder diffraction patterns of Cu 2 PO 4 OH between 100 and 280 K. Arrows show additional reflections that appear below 160 K in the monoclinic P2 1 /n phase. Highlights: → A low-temperature phase transition was found in the mineral libethenite Cu 2 PO 4 OH. → No magnetic anomalies and weak specific heat anomalies are detected. → Phase transition is of the second order. → Libethenite may exemplify a general feature of the adamite-type compounds.

Development of object oriented program `SONSHO` for strength evaluation. Manual of Version 4.0 program

Energy Technology Data Exchange (ETDEWEB)

Hosogai, Hiromi [Joyo Industries Co. Ltd., Tokai, Ibaraki (Japan); Kasahara, Naoto

1998-07-01

Object Oriented Program `SONSHO` predicts creep fatigue damage factors based on Elevated Temperature Structural Design Guide for `Monju` and other various procedures from stress classification data obtained from structural analysis results. From view point of program implementation, it is required that external programs interface and frequent revise from update of material and creep fatigue evaluation methods. Object oriented approach was continuously introduced to improve these aspects of the program. Version 4.0 has the following new functions. (1) Material strength library was implemented as an independent program module based on Microsoft Active X control and 32bitDLL technologies, which can be accessed by general Windows programs. (2) Self instruction system `Wizard` enables manual less operation. (3) Microsoft common object model (COM) was adopted for program interface, and this program can communicate with Excel sheet data on memory. Sonsho Ver.4.0 can work on Windows 95 or Windows NT4.0. Microsoft Visual Basic 5.0 (Enterprose Edition) and Microsoft FORTRAN Power Station 4.0 were adopted for program. (author)

A 4-channel 3 Tesla phased array receive coil for awake rhesus monkey fMRI and diffusion MRI experiments.

Science.gov (United States)

Khachaturian, Mark Haig

2010-01-01

Awake monkey fMRI and diffusion MRI combined with conventional neuroscience techniques has the potential to study the structural and functional neural network. The majority of monkey fMRI and diffusion MRI experiments are performed with single coils which suffer from severe EPI distortions which limit resolution. By constructing phased array coils for monkey MRI studies, gains in SNR and anatomical accuracy (i.e., reduction of EPI distortions) can be achieved using parallel imaging. The major challenges associated with constructing phased array coils for monkeys are the variation in head size and space constraints. Here, we apply phased array technology to a 4-channel phased array coil capable of improving the resolution and image quality of full brain awake monkey fMRI and diffusion MRI experiments. The phased array coil is that can adapt to different rhesus monkey head sizes (ages 4-8) and fits in the limited space provided by monkey stereotactic equipment and provides SNR gains in primary visual cortex and anatomical accuracy in conjunction with parallel imaging and improves resolution in fMRI experiments by a factor of 2 (1.25 mm to 1.0 mm isotropic) and diffusion MRI experiments by a factor of 4 (1.5 mm to 0.9 mm isotropic).

Phased Startup Initiative Phase 3 and 4 Test Procedure (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.

2000-01-01

The purpose of this test procedure is to safely operate the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) with specific fuel canisters, and show that canisters containing fuel can be retrieved from the canister queue, decapped in the Canister Decapper, and loaded into the Primary Clean Machine (PCM) for fuel cleaning; and that fuel can be sorted on the Process Table, then loaded back into fuel canisters and relocated in basin storage. An option is included to load selected elements into multi-canister overpack (MCO) Fuel Baskets. Additional Data are collected during this test, beyond that collected during production operations. These data support qualifying the cleaning performance of the PCM, assessing the quantity of scrap generated during the cleaning, and evaluating the impact of fuel retrieval operations on the Basin water quality. The additional data collected primarily consist of weighing fuel and scrap at selected points in the operation, as well as photographing fuel and scrap as it is processed. The time to perform operations is also monitored for comparison with design predictions. Water quality data are collected to establish a baseline to predict the effectiveness of equipment design for control of contamination and visibility during production operation. The scope of this test procedure is to validate the operation of FRS and IWTS components as a complete system. Fuel canisters shall be processed in accordance with this test procedure such that fuel inspection results are clearly attributed to a particular set of PCM operating parameters. The Phase 3 test sequence processes a minimum of six canisters. Twenty-four contingency canisters have been identified, and will be processed if additional performance data are required. The Phase 4 test sequence processes a minimum of 29 specific canisters. Twenty-nine contingency canisters have been identified for Phase 4 activities and will be processed to complete process validation, if

Composition and property measurements for PHA Phase 4 glasses

International Nuclear Information System (INIS)

Edwards, T.B.

2000-01-01

The results presented in this report are for nine Precipitate Hydrolysis Aqueous (PHA) Phase 4 glasses. Three of the glasses contained HM sludge at 22, 26, and 30 wt% respectively, 10 wt% PHA and 1.25 wt% monosodium titanate (MST), all on an oxide basis. The remaining six glasses were selected from the Phase 1 and Phase 2 studies (Purex sludge) but with an increased amount of MST. The high-end target for MST of 2.5 wt% oxide was missed in Phases 1 and 2 due to ∼30 wt% water content of the MST. A goal of this Phase 4 study was to determine whether this increase in titanium concentration from the MST had any impact on glass quality or processibility. Two of the glasses, pha14c and pha15c, were rebatched and melted due to apparent batching errors with pha14 and pha15. The models currently in the Defense Waste Processing Facility's (DWPF) Product Composition Control System (PCCS) were used to predict durability, homogeneity, liquidus, and viscosity for these nine glasses. All of the HM glasses and half of the Purex glasses were predicted to be phase separated, and consequently prediction of glass durability is precluded with the cument models for those glasses that failed the homogeneity constraint. If one may ignore the homogeneity constraint, the measured durabilities were within the 95% prediction limits of the model. Further efforts will be required to resolve this issue on phase separation (inhomogeneity). The liquidus model predicted unacceptable liquidus temperatures for four of the nine glasses. The approximate, bounding liquidus temperatures measured for all had upper limits of 1,000 C or less. Given the fact that liquidus temperatures were only approximated, the 30 wt% loading of Purex may be near or at the edge of acceptability for liquidus. The measured viscosities were close to the predictions of the model. For the Purex glasses, pha12c and pha15c, the measured viscosities of 28 and 23 poise, respectively, indicate that DWPF processing may be compromised

Phase controlled solvothermal synthesis of Cu_2ZnSnS_4, Cu_2ZnSn(S,Se)_4 and Cu_2ZnSnSe_4 Nanocrystals: The effect of Se and S sources on phase purity

International Nuclear Information System (INIS)

Pal, Mou; Mathews, N.R.; Paraguay-Delgado, F.; Mathew, X.

2015-01-01

In this study, we have reported the synthesis of Cu_2ZnSnSe_4 (CZTSe), Cu_2ZnSnS_4 (CZTS) and Cu_2ZnSn(S,Se)_4 (CZTSSe) nanocrystals with tunable band gap and composition obtained by solvothermal method. The crystalline structure, composition, morphology and optical properties of the nanoparticles were characterized by X-ray diffraction (XRD), Raman scattering, energy dispersive X-ray spectroscopy, transmission electron microscopy and diffuse reflectance (DR) spectroscopy. While the XRD patterns of CZTS and CZTSe nanoparticles prepared with elemental S/Se powder revealed the presence of phase pure nanoparticles, the CZTSSe nanoparticles obtained using a mixture of S and Se, were found to contain many secondary phases under the same synthesis protocol. Formation of impurity phases in CZTSSe sample, can be avoided by using a mixture of 1-dodecanethiol (DT; CH_3(CH_2)_1_1SH)/oleylamine (OLA) instead of S powder and following the same experimental procedure. The incorporation of S in CZTSe nanocrystals prepared in presence of DDT/OLA mixture was confirmed through structural and optical characterizations. The optical properties of the quaternary chalcogenide nanocrystals were found to vary with the chemical composition of the material. - Highlights: • Solvothermal synthesis of CZTS, CZTSSe and CZTSe nanocrystals and discussion on possible formation mechanism. • Use of dodecanethiol/oleylamine mixture to synthesize phase-pure CZTSSe nanocrystals. • Formation of impurity phases can be controlled with proper S and Se sources.

COMMIX-1A: a three-dimensional transient single-phase computer program for thermal hydraulic analysis of single and multicomponent systems. Volume I: users manual

International Nuclear Information System (INIS)

Domanus, H.M.; Schmitt, R.C.; Sha, W.T.; Shah, V.L.

1983-12-01

The COMMIX-1A computer program is an updated and improved version of COMMIX-1 designed to analyze steady-state/transient, single-phase, three-dimensional fluid flow with heat transfer in reactor components and multicomponent systems. A new porous-media formulation via local volume averaging has been derived and employed in the COMMIX code. The concepts of volume porosity, directional surface permeability, distributed resistance, and distributed heat source or sink is used in the new porous-media formulation to model a flow domain with stationary structures. The concept of directional surface permeability is new and greatly facilitates modeling of velocity and temperature fields in anisotropic media. The new porous-media formulation represents the first unified approach to thermal-hydraulic analysis. It is now possible to perform a multidimensional thermal-hydraulic simulation of either a single component, such as a rod bundle, reactor plenum, piping system, heat exchanger, etc., or a multicomponent system that is a combination of these components. The conservation equations of mass, momentum, and energy based on the new porous-media formulation are solved as a boundary-value problem in space and an initial-value problem in time. Two other unique features provided in the COMMIX-1A code are (1) two solution procedures - a semi-implicit procedure modified from ICE and a fully-implicit procedure, named SIMPLEST-ANL, similar to the SIMPLE/SIMPLER algorithms - available a user's option and (2) a geometrical package capable of approximating many geometries. This report (Volume I) describes in detail the basic equations, formulations, solution procedures, flow charts, rebalancing scheme for faster convergence, options available to users, models to describe the auxiliary phenomena, input instructions, and two sample problems. The Volume II assembles and summarizes the results of many simulations that have been performed with COMMIX-1A computer program

Epstein-Barr virus BGLF4 kinase retards cellular S-phase progression and induces chromosomal abnormality.

Directory of Open Access Journals (Sweden)

Yu-Hsin Chang

Full Text Available Epstein-Barr virus (EBV induces an uncoordinated S-phase-like cellular environment coupled with multiple prophase-like events in cells replicating the virus. The EBV encoded Ser/Thr kinase BGLF4 has been shown to induce premature chromosome condensation through activation of condensin and topoisomerase II and reorganization of the nuclear lamina to facilitate the nuclear egress of nucleocapsids in a pathway mimicking Cdk1. However, the observation that RB is hyperphosphorylated in the presence of BGLF4 raised the possibility that BGLF4 may have a Cdk2-like activity to promote S-phase progression. Here, we investigated the regulatory effects of BGLF4 on cell cycle progression and found that S-phase progression and DNA synthesis were interrupted by BGLF4 in mammalian cells. Expression of BGLF4 did not compensate Cdk1 defects for DNA replication in S. cerevisiae. Using time-lapse microscopy, we found the fate of individual HeLa cells was determined by the expression level of BGLF4. In addition to slight cell growth retardation, BGLF4 elicits abnormal chromosomal structure and micronucleus formation in 293 and NCP-TW01 cells. In Saos-2 cells, BGLF4 induced the hyperphosphorylation of co-transfected RB, while E2F1 was not released from RB-E2F1 complexes. The E2F1 regulated activities of the cyclin D1 and ZBRK1 promoters were suppressed by BGLF4 in a dose dependent manner. Detection with phosphoamino acid specific antibodies revealed that, in addition to Ser780, phosphorylation of the DNA damage-responsive Ser612 on RB was enhanced by BGLF4. Taken together, our study indicates that BGLF4 may directly or indirectly induce a DNA damage signal that eventually interferes with host DNA synthesis and delays S-phase progression.

Research and development toward a 4.5-1.5{angstrom} linac coherent light source (LCLS) at SLAC

Energy Technology Data Exchange (ETDEWEB)

Tatchyn, R.; Arthur, J.; Baltay, M. [Stanford Univ., CA (United States)] [and others

1995-12-31

In recent years significant studies have been initiated on the theoretical and technical feasibility of utilizing a portion of the 3km S-band accelerator at the Stanford Linear Accelerator Center (SLAC) to drive a short wavelength (4.5-1.5 {Angstrom}) Linac Coherent Light Source (LCLS), a Free-Electron Laser (FEL) operating in the Self-Amplified Spontaneous Emission (SASE) regime. Electron beam requirements for single-pass saturation include: (1) a peak current in the 3-7 kA range, (2) a relative energy spread of <0.05%, ad (3) a transverse emittance, {epsilon}{le}{lambda}/4{pi}, where {lambda}[m] is the output wavelength. Requirements on the insertion device include field error levels of 0.1-0.2% for keeping the electron bunch centered on and in phase with the amplified photons, and a focusing beta of 4-8 m for inhibiting the dilution of its transverse density. Although much progress techniques necessary for LCLS operation down to {approximately}20 {angstrom}, a substantial amount of research and development is still required in a number of theoretical and experimental areas leading to the construction and operation of a 4.5-1.5 {angstrom} LCLS. In this paper we report on a research and development program underway and in planning at SLAC for addressing critical questions in these areas. These include the construction and operation of a linac test stand for developing laser-driven photocathode rf guns with normalized emittances approaching 1 mm-mr; development of advanced beam compression, stability, an emittance control techniques at multi-GeV energies; the construction and operation of a FEL Amplifier Test Experiment (FATE) for theoretical and experimental studies of SASE at IR wavelengths; an undulator development program to investigate superconducting, hybrid/permanent magnet (hybrid/PM), and pulsed-Cu technologies; theoretical and computational studies of high-gain FEL physics and LCLS component designs.

Oxygen Exchange and Transport in (La0.6Sr0.4)0.98FeO3-d – Ce0.9Gd0.1O1.95 Dual-Phase Composites

DEFF Research Database (Denmark)

Ovtar, Simona; Søgaard, Martin; Norrman, Kion

2018-01-01

The chemical diffusion coefficient and the effective surface exchange coefficient (kex) of dual-phase (La0.6Sr0.4)0.98FeO3-d (LSF) − Ce0.9Gd0.1O1.95 (CGO) composites containing between 30 and 70 vol.% of CGO were determined by electrical conductivity relaxation (ECR) at high oxygen partial...... pressures (10−3 .../s for a 70 vol.% of CGO in the composite at 750°C for a pO2 change from 0.2 to 1.0 atm. The experiments demonstrate that the kex is enhanced due to a synergistic effect between the two phases, and suggest a direct involvement of CGO phase in the oxygen surface exchange reaction. Possible mechanisms...

Electron Number-Based Phase Diagram of Pr1 -xLaCex CuO4 -δ and Possible Absence of Disparity between Electron- and Hole-Doped Cuprate Phase Diagrams

Science.gov (United States)

Song, Dongjoon; Han, Garam; Kyung, Wonshik; Seo, Jeongjin; Cho, Soohyun; Kim, Beom Seo; Arita, Masashi; Shimada, Kenya; Namatame, Hirofumi; Taniguchi, Masaki; Yoshida, Y.; Eisaki, H.; Park, Seung Ryong; Kim, C.

2017-03-01

We performed annealing and angle resolved photoemission spectroscopy studies on electron-doped cuprate Pr1 -xLaCex CuO4 -δ (PLCCO). It is found that the optimal annealing condition is dependent on the Ce content x . The electron number (n ) is estimated from the experimentally obtained Fermi surface volume for x =0.10 , 0.15 and 0.18 samples. It clearly shows a significant and annealing dependent deviation from the nominal x . In addition, we observe that the pseudo-gap at hot spots is also closely correlated with n ; the pseudogap gradually closes as n increases. We established a new phase diagram of PLCCO as a function of n . Different from the x -based one, the new phase diagram shows similar antiferromagnetic and superconducting phases to those of hole doped ones. Our results raise a possibility for absence of disparity between the phase diagrams of electron- and hole-doped cuprates

Lattice parameter values and phase transitions for the Cu{sub 2}Cd{sub 1-z}Mn {sub z}GeSe{sub 4} and Cu{sub 2}Cd{sub 1-z}Fe {sub z}GeSe{sub 4} alloys

Energy Technology Data Exchange (ETDEWEB)

Quintero, E. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Tovar, R. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Quintero, M. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela)]. E-mail: mquinter@ula.ve; Delgado, G.E. [Laboratorio de Cristalografia, Departamento de Quimica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Morocoima, M. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Caldera, D. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Ruiz, J. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida 5101 (Venezuela); Mora, A.E. [Laboratorio de Analisis Quimico y Estructural de Materiales, Departamento de Fisica, Universidad de Los Andes, Merida 5101 (Venezuela); Briceno, M. [Laboratorio de Analisis Quimico y Estructural de Materiales, Departamento de Fisica, Universidad de Los Andes, Merida 5101 (Venezuela); Fernandez, J.L. [Laboratorio de Analisis Quimico y Estructural de Materiales, Departamento de Fisica, Universidad de Los Andes, Merida 5101 (Venezuela)

2007-04-25

X-ray powder diffraction measurements and differential thermal analysis (DTA) were made on polycrystalline samples of the Cu{sub 2}Cd{sub 1-z}Mn {sub z}GeSe{sub 4} and Cu{sub 2}Cd{sub 1-z}Fe {sub z}GeSe{sub 4} alloy systems. The diffraction patterns were used to show the equilibrium conditions and to derive lattice parameter values. The effect of the annealing temperature and cooling rate to room temperature are discussed. For the Cu{sub 2}Cd{sub 1-z}Fe {sub z}GeSe{sub 4} system, only two single solid phase fields, the tetragonal stannite {alpha} and the wurtz-stannite {delta} structures were found to occur in the diagram. For the Cu{sub 2}Cd{sub 1-z}Mn {sub z}GeSe{sub 4} system, in addition to the tetragonal stannite {alpha} and the wurtz-stannite {delta} phases, MnSe was found to exist in the diagram. The DTA experiments showed that the cooling curves for both systems exhibited effects of undercooling.

User's manual of BISHOP. A Bi-Phase, Sodium-Hydrogen-Oxygen system, chemical equilibrium calculation program

International Nuclear Information System (INIS)

Okano, Yasushi; Yamaguchi, Akira

2001-07-01

In an event of sodium leakage in liquid metal fast breeder reactors, liquid sodium flows out of piping, and droplet combustion might occur under a certain environmental condition. The combustion heat and reaction products should be evaluated in the sodium fire analysis codes for investigating the influence of the sodium leak age and fire incident. In order to analyze the reaction heat and products, the multi-phase chemical equilibrium calculation program for a sodium, oxygen and hydrogen system has been developed. The developed numerical program is named BISHOP, which denotes 'Bi-Phase, Sodium-Hydrogen-Oxygen, Chemical Equilibrium Calculation Program'. The Gibbs free energy minimization method is used because of the following advantages. Chemical species are easily added and changed. A variety of thermodynamic states, such as isothermal and isentropic changes, can be dealt with in addition to constant temperature and pressure processes. In applying the free energy minimization method to solve the multi-phase sodium reaction system, three new numerical calculation techniques are developed. One is theoretical simplification of phase description in equation system, the other is to extend the Gibbs free energy minimization method to a multi-phase system, and the last is to establish the efficient search for the minimum value. The reaction heat and products at the equilibrium state can be evaluated from the initial conditions, such as temperature, pressure and reactants, using BISHOP. This report describes the thermochemical basis of chemical equilibrium calculations, the system of equations, simplification models, and the procedure to prepare input data and usage of BISHOP. (author)

TWRS Privatization Phase 1 Master Site Plan

International Nuclear Information System (INIS)

PARAZIN, R.J.

1999-01-01

The U.S. Department of Energy (DOE) has chosen to accomplish the Tank Waste Remediation System disposal mission via privatization. The disposal mission has been divided into two privatization phases. Phase I, a 'proof of concept' phase, will establish and demonstrate the technical, commercial, and procurement capabilities necessary far privatization to proceed. Once established, privatization will be expanded in the form of a second phase (Phase II) to dispose of the remainder of the tank waste. In conjunction with preparation of the Tank Waste Remediation System (TWRS) Privatization Request for Proposals (RFP)(RL, 1996), a location was selected for the Phase I demonstration facilities (Shord, 1996). The location selected was the area previously developed and characterized for the Grout Disposal Site, adjoining the 200 East Area. The site is of sufficient size for a Private Contractor (PC) to carry out pretreatment, immobilization, and vitrification operations and possesses the required characteristics (e.g., close to feed tanks) to best facilitate the Phase I operations. This overall long-range Master Site Plan (MSP) has been developed to establish a ''baseline'' for the (TWRS) Privatization Phase I (TPPI) PC Site. The MSP depicts the planned layout for the PC Site along with various interfaces between the site and other Hanford utilities and functions. The complete integration of TPPl MSP with overall Hanford Site planning process will assist in establishing the PC site and the necessary priorities to meet the Hanford cleanup mission. The MSP has been developed systematically into a comprehensive, safe, flexible, logical and cost-effective plan. The general philosophy behind the preparation of a MSP for the TPPl program is that it will serve as a single source documentation of the planning for the development of the TPPl complex. The effort will plan temporary and permanent land use, utilities, and traffic flow for the overall program. It will identify needs

Transverse emittance and phase space program developed for use at the Fermilab A0 Photoinjector

International Nuclear Information System (INIS)

Thurman-Keup, R.; Johnson, A.S.; Lumpkin, A.H.; Ruan, J.

2011-01-01

The Fermilab A0 Photoinjector is a 16 MeV high intensity, high brightness electron linac developed for advanced accelerator R and D. One of the key parameters for the electron beam is the transverse beam emittance. Here we report on a newly developed MATLAB based GUI program used for transverse emittance measurements using the multi-slit technique. This program combines the image acquisition and post-processing tools for determining the transverse phase space parameters with uncertainties. An integral part of accelerator research is a measurement of the beam phase space. Measurements of the transverse phase space can be accomplished by a variety of methods including multiple screens separated by drift spaces, or by sampling phase space via pepper pots or slits. In any case, the measurement of the phase space parameters, in particular the emittance, can be drastically simplified and sped up by automating the measurement in an intuitive fashion utilizing a graphical interface. At the A0 Photoinjector (A0PI), the control system is DOOCS, which originated at DESY. In addition, there is a library for interfacing to MATLAB, a graphically capable numerical analysis package sold by The Mathworks. It is this graphical package which was chosen as the basis for a graphical phase space measurement system due to its combination of analysis and display capabilities.

A combined experimental and DFT study of a novel unsymmetrical azine 2-(4-methoxybenzylidene)-1-(1-(4-isobutylphenyl) ethylidene) hydrazine

Science.gov (United States)

Vijaya, P.; Sankaran, K. R.

2015-03-01

A novel unsymmetrical azine 2-(4-methoxybenzylidene)-1-(1-(4-isobutylphenyl) ethylidene) hydrazine (UA) was prepared and characterized by IR, 1H and 13C NMR spectral studies. A 2D - potential energy scan (PES) of p-isobutylacetophenone (IBAP) was the portal to the conformational analysis of UA by density functional theory (DFT) methods using 6-31G(d,p) basis set by Gaussian 03 program. The theoretical IR frequencies were found to be in good agreement with the experimental values. The IR frequencies of UA were analyzed by means of Potential energy Distribution (PED %) calculation using Vibrational Energy Distribution Analysis (VEDA 4) program. The experimental NMR chemical shift values of UA were compared with the theoretical values obtained by DFT method. Nonlinear optical behavior of the unsymmetrical azine is also examined by the theoretically predicted values of dipole moment (μ), polarizability (α0) and first hyperpolarizability (βtot). Stability of the UA molecule has been analyzed using NBO analysis. The electrochemistry of UA studied experimentally by cyclic voltammetry is complemented by the computational analysis of the anionic form of the molecule UA. The determination of various global and local reactivity descriptors in the context of chemical reactivity is also performed and the electrophilicity at the vital atomic sites in UA is revealed. Bader's Atoms in molecules (AIM) theory of UA indicated the presence of intramolecular hydrogen bonding in the molecule. The molecular electrostatic potential (MEP) and HOMO-LUMO orbital analysis are also performed for the molecule UA.

Phase transitions and molecular motions in [Ni(ND3)6](ClO4)2

International Nuclear Information System (INIS)

Migdal-Mikuli, Anna; Mikuli, Edward; Gorska, Natalia; Kowalska, Aneta; Ulanski, Jacek

2004-01-01

[Ni(ND 3 ) 6 ](ClO 4 ) 2 has three solid phases between 100 and 300 K. The phase transitions temperatures at heating (T C1 h =164.1 K and T C2 h =145.1 K) are shifted, as compared to the non-deuterated compound, towards the lower temperature of ca. 8 and 5 K, respectively. The ClO 4 - anions perform fast, picosecond, isotropic reorientation with the activation energy of 6.6 kJ mol -1 , which abruptly slow down at T C1 c phase transition, during sample cooling. The ND 3 ligands perform fast uniaxial reorientation around the Ni-N bond in all three detected phases, with the effective activation energy of 2.9 kJ mol -1 . The reorientational motion of ND 3 is only slightly distorted at the T C1 phase transition due to the dynamical orientational order-disorder process of anions. The low value of the activation energy for the ND 3 reorientation suggests that this reorientation undergoes the translation-rotation coupling, which makes the barrier to the rotation of the ammonia ligands not constant but fluctuating. The phase polymorphism and the dynamics of the molecular reorientations of the title compound are similar but not quite identical with these of the [Ni(NH 3 ) 6 ](ClO 4 ) 2

Small business innovation research program solicitation

Science.gov (United States)

1994-01-01

The National Aeronautics and Space Administration invites eligible small business concerns to submit Phase 1 proposals for its 1994 Small Business Innovation Research (SBIR) Program, which is described in this twelfth annual NASA SBIR Program Solicitation. The 1994 solicitation period for Phase 1 proposals begins April 4, 1994 and ends June 15, 1994. Eligible firms with research or research and development capabilities (R/R&D) in any of the listed topic and subtopic areas are encouraged to participate. Through SBIR, NASA seeks innovative concepts addressing the program needs described in the SBIR solicitation subtopics and offering commercial application potential. This document contains program background information, outlines eligibility requirements for SBIR participants, describes the three SBIR program phases, and provides the information qualified offerors need to prepare and submit responsive proposals.

Reliability program plan for the Isotope Brayton Ground Demonstration System (phase I)

International Nuclear Information System (INIS)

1975-01-01

The reliability and quality assurance organizational relationships, the methods to be used, the tasks to be completed, and the documentation to be published are presented. The total program is intended to provide the necessary reliability and quality assurance associated with the design, fabrication, and testing of the GDS. It is consistent with the general objectives of the ERDA Quality Assurance (QA) program requirements document ''SNS-1'' dated April 1972 and reliability program requirements document ''SNS-2'' dated 17 June 1974 but has been specifically modified for the GDS with the intent of establishing background data for the subsequent Phase II effort

Prolonged early G1 arrest by selective CDK4/CDK6 inhibition sensitizes myeloma cells to cytotoxic killing through cell cycle–coupled loss of IRF4

Science.gov (United States)

Huang, Xiangao; Di Liberto, Maurizio; Jayabalan, David; Liang, Jun; Ely, Scott; Bretz, Jamieson; Shaffer, Arthur L.; Louie, Tracey; Chen, Isan; Randolph, Sophia; Hahn, William C.; Staudt, Louis M.; Niesvizky, Ruben; Moore, Malcolm A. S.

2012-01-01

Dysregulation of cyclin-dependent kinase 4 (CDK4) and CDK6 by gain of function or loss of inhibition is common in human cancer, including multiple myeloma, but success in targeting CDK with broad-spectrum inhibitors has been modest. By selective and reversible inhibition of CDK4/CDK6, we have developed a strategy to both inhibit proliferation and enhance cytotoxic killing of cancer cells. We show that induction of prolonged early-G1 arrest (pG1) by CDK4/CDK6 inhibition halts gene expression in early-G1 and prevents expression of genes programmed for other cell-cycle phases. Removal of the early-G1 block leads to S-phase synchronization (pG1-S) but fails to completely restore scheduled gene expression. Consequently, the IRF4 protein required to protect myeloma cells from apoptosis is markedly reduced in pG1 and further in pG1-S in response to cytotoxic agents, such as the proteasome inhibitor bortezomib. The coordinated loss of IRF4 and gain of Bim sensitize myeloma tumor cells to bortezomib-induced apoptosis in pG1 in the absence of Noxa and more profoundly in pG1-S in cooperation with Noxa in vitro. Induction of pG1 and pG1-S by reversible CDK4/CDK6 inhibition further augments tumor-specific bortezomib killing in myeloma xenografts. Reversible inhibition of CDK4/CDK6 in sequential combination therapy thus represents a novel mechanism-based cancer therapy. PMID:22718837

Prolonged early G(1) arrest by selective CDK4/CDK6 inhibition sensitizes myeloma cells to cytotoxic killing through cell cycle-coupled loss of IRF4.

Science.gov (United States)

Huang, Xiangao; Di Liberto, Maurizio; Jayabalan, David; Liang, Jun; Ely, Scott; Bretz, Jamieson; Shaffer, Arthur L; Louie, Tracey; Chen, Isan; Randolph, Sophia; Hahn, William C; Staudt, Louis M; Niesvizky, Ruben; Moore, Malcolm A S; Chen-Kiang, Selina

2012-08-02

Dysregulation of cyclin-dependent kinase 4 (CDK4) and CDK6 by gain of function or loss of inhibition is common in human cancer, including multiple myeloma, but success in targeting CDK with broad-spectrum inhibitors has been modest. By selective and reversible inhibition of CDK4/CDK6, we have developed a strategy to both inhibit proliferation and enhance cytotoxic killing of cancer cells. We show that induction of prolonged early-G(1) arrest (pG1) by CDK4/CDK6 inhibition halts gene expression in early-G(1) and prevents expression of genes programmed for other cell-cycle phases. Removal of the early-G(1) block leads to S-phase synchronization (pG1-S) but fails to completely restore scheduled gene expression. Consequently, the IRF4 protein required to protect myeloma cells from apoptosis is markedly reduced in pG1 and further in pG1-S in response to cytotoxic agents, such as the proteasome inhibitor bortezomib. The coordinated loss of IRF4 and gain of Bim sensitize myeloma tumor cells to bortezomib-induced apoptosis in pG1 in the absence of Noxa and more profoundly in pG1-S in cooperation with Noxa in vitro. Induction of pG1 and pG1-S by reversible CDK4/CDK6 inhibition further augments tumor-specific bortezomib killing in myeloma xenografts. Reversible inhibition of CDK4/CDK6 in sequential combination therapy thus represents a novel mechanism-based cancer therapy.

Monoclinic MB phase and phase instability in [110] field cooled Pb(Zn1/3Nb2/3)O3-4.5%PbTiO3 single crystals

Science.gov (United States)

Yao, Jianjun; Cao, Hu; Ge, Wenwei; Li, Jiefang; Viehland, D.

2009-08-01

We report the finding of a monoclinic MB phase in Pb(Zn1/3Nb2/3)O3-4.5%PbTiO3 single crystals. High precision x-ray diffraction investigations of [110] field cooled crystals have shown a transformation sequence of cubic(C)→tetragonal(T)→orthorhombic(O)→monoclinic(MB), which is different from that previously reported [A.-E. Renault et al., J. Appl. Phys. 97, 044105 (2005)]. Beginning in the zero-field-cooled condition at 383 K, a rhombohedral (R)→MB→O sequence was observed with increasing field. Coexisting MB and O phases were then found upon removal of field, which fully transformed to MB on cooling to room temperature.

Method of forming an oxide superconducting thin film having an R1A2C3 crystalline phase over an R2A1C1 crystalline phase

International Nuclear Information System (INIS)

Lelental, M.; Romanofsky, H.J.

1992-01-01

This patent describes a process which comprises forming a mixed rare earth alkaline earth copper oxide layer on a substrate and converting the mixed rare earth alkaline earth copper oxide layer to an electrically conductive layer. It comprises crystalline R 1 A 2 C 3 oxide phase by heating in the presence of oxygen, wherein rare earth and R is in each instance chosen from among yttrium, lanthanum, samarium, europium, gadolinium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium and alkaline earth and A is in each instance chosen from among calcium, strontium and barium, characterized in that a crystalline R 2 A 1 C 1 oxide phase is first formed as a layer on the substrate and the crystalline R 1 A 2 C 3 oxide phase is formed over the crystalline R 2 A 1 C 1 oxide phase by coating a mixed rare earth alkaline earth copper oxide on the crystalline R 2 A 1 C 1 oxide phase and heating the mixed rare earth alkaline earth copper oxide to a temperature of at least 1000 degrees C

Solid-phase synthesis of NH-1,2,3-triazoles using 4,4′- bismethoxybenzhydryl azide

DEFF Research Database (Denmark)

Cohrt, Anders Emil O'Hanlon; Le Quement, Sebastian Thordal; Nielsen, Thomas Eiland

2014-01-01

Readily available 4,4′-bismethoxybenzhydryl azide was found to be a useful building block for the synthesis of NH-1,2,3-triazoles through copper(I)-catalyzed cycloaddition reactions with solid-supported terminal alkynes, followed by acid-mediated deprotection. Peptide-containing NH-1,2,3-triazole...

Army-NASA aircrew/aircraft integration program (A3I) software detailed design document, phase 3

Science.gov (United States)

Banda, Carolyn; Chiu, Alex; Helms, Gretchen; Hsieh, Tehming; Lui, Andrew; Murray, Jerry; Shankar, Renuka

1990-01-01

The capabilities and design approach of the MIDAS (Man-machine Integration Design and Analysis System) computer-aided engineering (CAE) workstation under development by the Army-NASA Aircrew/Aircraft Integration Program is detailed. This workstation uses graphic, symbolic, and numeric prototyping tools and human performance models as part of an integrated design/analysis environment for crewstation human engineering. Developed incrementally, the requirements and design for Phase 3 (Dec. 1987 to Jun. 1989) are described. Software tools/models developed or significantly modified during this phase included: an interactive 3-D graphic cockpit design editor; multiple-perspective graphic views to observe simulation scenarios; symbolic methods to model the mission decomposition, equipment functions, pilot tasking and loading, as well as control the simulation; a 3-D dynamic anthropometric model; an intermachine communications package; and a training assessment component. These components were successfully used during Phase 3 to demonstrate the complex interactions and human engineering findings involved with a proposed cockpit communications design change in a simulated AH-64A Apache helicopter/mission that maps to empirical data from a similar study and AH-1 Cobra flight test.

A novel synthesis of octahydropyrido[3,2-c]carbazole framework of aspidospermidine alkaloids and a combined computational, FT-IR, NMR, NBO, NLO, FMO, MEP study of the cis-4a-Ethyl-1-(2hydroxyethyl)-2,3,4,4a,5,6,7,11c-octahydro-1H-pyrido[3,2-c]carbazole

Science.gov (United States)

Uludağ, Nesimi; Serdaroğlu, Goncagul; Yinanc, Abdullah

2018-06-01

In this study, we performed a novel synthesis of the octahydropyrido[3,2-c]carbazole derivative 6 from 1 in five steps with a 34% overall yield. We also developed a unique compound 2 by a cyclization reaction from the cyanoethylation of compound 1, which is an intermediate step in the synthesis of Aspidospermidine. The parent compound of Aspidospermidine alkaloids, comprise a large family of diverse structures. As a result, we obtained octahydropyrido[3,2-c]carbazole (6)and the proposed method may be applicable to other alkaloids. All quantum chemical calculations of the cis-4a-Ethyl-1-(2-hydroxyethyl)-2,3,4,4a,5,6,7,11c-octahydro-1H-pyrido[3,2-c]carbazole have been performed with the DFT/B3LYP and HF methods by using the Gaussian 09W software package. The most stable conformer obtained from the Potential Energy Surface (PES) scan analysis at the B3LYP/6-31G** level of theory in the gas phase was used as the starting structure of the title compound to further computational analysis. The Natural Bond Orbital (NBO) and NLO analyses were performed to evaluate the intra-molecular interactions contributing to the molecular stability and to predict the optical properties of the title compound, respectively. Gauge-Independent Atomic Orbital (GIAO) approach was used to determine the 1H and 1C NMR chemical shifts of the title compound by subtracting the shielding constants of TMS at both methods. The calculated vibrational frequencies of the title compound were assigned by using the VEDA program and were scaled down by using the scaling factor 0.9668 for B3LYP/6-311++G(d, p) and 0.9050 for HF/6-311++G(d, p) to improve the calculated vibrational frequencies. The FMO (frontier molecular orbital) analysis was evaluated to predict the chemical and physical properties of the title compound and the HOMO, LUMO, and MEP diagrams were visualized by GaussView 4.1 program to present the reactive site of the title compound.

Bright Localized Near-Infrared Emission at 1-4 AU in the AB Aurigae Disk Revealed by IOTA Closure Phases

Science.gov (United States)

Millan-Gabet, R.; Monnier, J. D.; Berger, J.-P.; Traub, W. A.; Schloerb, F. P.; Pedretti, E.; Benisty, M.; Carleton, N. P.; Haguenauer, P.; Kern, P.; Labeye, P.; Lacasse, M. G.; Malbet, F.; Perraut, K.; Pearlman, M.; Thureau, N.

2006-07-01

We report on the detection of localized off-center emission at 1-4 AU in the circumstellar environment of the young stellar object AB Aurigae. We used closure-phase measurements in the near-infrared that were made at the long-baseline interferometer IOTA, the first obtained on a young stellar object using this technique. When probing sub-AU scales, all closure phases are close to zero degrees, as expected given the previously determined size of the AB Aurigae inner-dust disk. However, a clear closure-phase signal of -3.5d +/- 0.5d is detected on one triangle containing relatively short baselines, requiring a high degree of non-point symmetry from emission at larger (AU-sized) scales in the disk. We have not identified any alternative explanation for these closure-phase results, and we demonstrate that a ``disk hot spot'' model can fit our data. We speculate that such detected asymmetric near-infrared emission might arise as a result of localized viscous heating due to a gravitational instability in the AB Aurigae disk, or to the presence of a close stellar companion or accreting substellar object.

Experimental studies of interaction mechanisms and phase transport processes in two-phase flow (NOVA program)

International Nuclear Information System (INIS)

Sauter, H.; Meyder, R.; Philipp, P.; Samstag, M.

1995-01-01

The NOVA program was continued with turbulent, vertical, upward two-phase flow experiments. The development of a local gas distribution along the test section was visualized by X-ray tomography. (orig.)

Program PLOTC4. (Version 87-1). Plot evaluated data from the ENDF/B format and/or experimental data which is in a computation format

International Nuclear Information System (INIS)

Cullen, D.E.

1987-06-01

Experimental and evaluated nuclear reaction data are world-wide compiled in EXFOR format (see document IAEA-NDS-1) and ENDF format (see document IAEA-NDS-10), respectively. The computer program PLOTC4 described in the present document plots data from both formats; EXFOR data must be converted first to a ''computation format'' (see document IAEA-NDS-80). The program is available upon request costfree from the IAEA Nuclear Data Section. (author)

Detection of high PD-L1 expression in oral cancers by a novel monoclonal antibody L1Mab-4.

Science.gov (United States)

Yamada, Shinji; Itai, Shunsuke; Kaneko, Mika K; Kato, Yukinari

2018-03-01

Programmed cell death-ligand 1 (PD-L1), which is a ligand of programmed cell death-1 (PD-1), is a type I transmembrane glycoprotein that is expressed on antigen-presenting cells and several tumor cells, including melanoma and lung cancer cells. There is a strong correlation between human PD-L1 (hPD-L1) expression on tumor cells and negative prognosis in cancer patients. In this study, we produced a novel anti-hPD-L1 monoclonal antibody (mAb), L 1 Mab-4 (IgG 2b , kappa), using cell-based immunization and screening (CBIS) method and investigated hPD-L1 expression in oral cancers. L 1 Mab-4 reacted with oral cancer cell lines (Ca9-22, HO-1-u-1, SAS, HSC-2, HSC-3, and HSC-4) in flow cytometry and stained oral cancers in a membrane-staining pattern. L 1 Mab-4 stained 106/150 (70.7%) of oral squamous cell carcinomas, indicating the very high sensitivity of L 1 Mab-4. These results indicate that L 1 Mab-4 could be useful for investigating the function of hPD-L1 in oral cancers.

On the structural phase transitions of the perovskite-type layer structures (Csub(n)Hsub(2n+1)NH3)2MeCl4

International Nuclear Information System (INIS)

Heger, G.

1978-01-01

The perovskite-type layer compounds (Csub(n)Hsub(2n+1)NH 3 ) 2 MeCl 4 show a variety of different structural modifications. They differ from oneanother by the order and dynamical behaviour of the CH 3 -CH 2 -...-CH 2 -NH 3 chain molecules and the [MeCl 6 ] octahedra layers. These two structural members are coupled together by N-H...Cl hydrogen bonds. According to group theoretical relations the modifications of (Csub(n)Hsub(2n+1)NH 3 ) 2 MeCl 4 were ordered in the scheme of a 'family tree'. Taking (CH 3 NH 3 ) 2 MnCl 4 as an example, various experimental investigations incorporated neutron diffraction are reported. They lead to a sequence of phase transitions. For these phase transitions a model is developed based on the orientations of the CH 3 NH 3 dump-bell molecules and their interactions with the [MnCl 6 ] layers. (orig./HPOE) [de

Evaluation of the phase composition of (NH4)2SO4 + (NH4)H2PO4 mixtures by X-ray diffractometry

International Nuclear Information System (INIS)

Ortiz, Angel L.; Cumbrera, Francisco L.; Perez, Jose; Vas, Beatriz del; Perez, Eduardo

2009-01-01

The phase composition of standard (NH 4 ) 2 SO 4 + (NH 4 )H 2 PO 4 mixtures was investigated by X-ray diffractometry (XRD) using the internal-standard, reference-intensity-ratio, and Rietveld methods. It was found that the Rietveld method yields the most accurate phase-composition measurements, with an average error of ∼2 wt.%. It was also found that the internal-standard method is only effective in determining the phase composition if the calibration curve for (NH 4 )H 2 PO 4 is used, giving an average error of ∼6.5 wt.%. On the contrary, the internal-standard method with the calibration curve of the (NH 4 ) 2 SO 4 phase and the reference-intensity-ratio method are not valid. The inappropriateness of these two methods was attributed to graininess in the (NH 4 ) 2 SO 4 phase, with the attendant deviation of its diffracted intensities from the theoretical values. Direct scanning electron microscopy observations of the morphology of the powder particles in the mixtures showed clear evidence of the large agglomerates formed because the individual powder particles are partially sintered together during milling, thus corroborating the graininess determined by the XRD analyses. Finally, the implications of the present study for the quantitative phase-composition analysis of (NH 4 ) 2 SO 4 + (NH 4 )H 2 PO 4 mixtures, which are of great technological importance for the fire prevention industry, are discussed.

Reconstructive phase transition in (NH4)3TiF7 accompanied by the ordering of TiF6 octahedra.

Science.gov (United States)

Molokeev, Maxim; Misjul, S V; Flerov, I N; Laptash, N M

2014-12-01

An unusual phase transition P4/mnc → Pa\\bar 3 has been detected after cooling the (NH4)3TiF7 compound. Some TiF6 octahedra, which are disordered in the room-temperature tetragonal structure, become ordered in the low-temperature cubic phase due to the disappearance of the fourfold axis. Other TiF6 octahedra undergo large rotations resulting in huge displacements of the F atoms by 1.5-1.8 Å that implies a reconstructive phase transition. It was supposed that phases P4/mbm and Pm\\bar 3m could be a high-temperature phase and a parent phase, respectively, in (NH4)3TiF7. Therefore, the sequence of phase transitions can be written as Pm\\bar 3m → P4/mbm → P4/mnc → Pa\\bar 3. The interrelation between (NH4)3TiF7, (NH4)3GeF7 and (NH4)3PbF7 is found, which allows us to suppose phase transitions in relative compounds.

Small Business Innovation Research: Abstracts of Phase 1 awards, 1994

Energy Technology Data Exchange (ETDEWEB)

1994-12-31

The Small Business Innovation Research (SBIR) program enables DOE to obtain effective, innovative solutions to important problems through the private sector, which has a commercial incentive to pursue the resulting technology and bring it to the marketplace. The growing number of awardees, many of them started in business in response to SBIR solicitations, is becoming a significant resource for the solution of high risk, high technology problems for the Department. As detailed here, this publication describes the technical efforts for SBIR Phase 1 awards in 1994. It is intended for the educated layman, and may be of particular interest to potential investors who wish to get in on the ground floor of exciting opportunities. Contained in this booklet are abstracts of the Phase 1 awards made in FY 1994 under the DOE SBIR program. The 212 Phase 1 projects described here were selected in a highly competitive process from a total of 2,276 grant applications received in response to the 1994 DOE annual SBIR Solicitation. The selections for awards were made on scientific and technical merit, as judged against the specific criteria listed in the Solicitation. Conclusions were reached on the basis of detailed reports returned by reviewers drawn from DOE laboratories, universities, private industry, and government. (Any discrepancies noted in prior DOE releases naming the firms selected for awards are due either to the firm changing its name after the award selection or to the firm not proceeding to a signed grant.) It is expected that between one-third and one-half of the Phase 1 projects will be continued into Phase 2. The work described in the abstracts is novel, high-risk research, but the benefits will also be potentially high if the objectives are met. Brief comments on the potential applications are given after each abstract. Individuals and organizations with an interest in the research described are encouraged to contact the appropriate small business directly.

RIS4E Science Journalism Program

Science.gov (United States)

Whelley, N.; Bleacher, L.; Jones, A. P.; Bass, E.; Bleacher, J. E.; Firstman, R.; Glotch, T. D.; Young, K.

2017-12-01

NASA's Remote, In-Situ, and Synchrotron Studies for Science and Exploration (RIS4E) team addresses the goals of the Solar System Exploration Research Virtual Institute via four themes, one of which focuses on evaluating the role of handheld and portable field instruments for human exploration. The RIS4E Science Journalism Program highlights science in an innovative way: by instructing journalism students in the basics of science reporting and then embedding them with scientists in the field. This education program is powerful because it is deeply integrated within a science program, strongly supported by the science team and institutional partners, and offers an immersive growth experience for learners, exposing them to cutting edge NASA research and field technology. This program is preparing the next generation of science journalists to report on complex science accurately and effectively. The RIS4E Science Journalism Program consists of two components: a semester-long science journalism course and a reporting trip in the field. First, students participate in the RIS4E Science Journalism Practicum offered by the Stony Brook University School of Journalism. Throughout the semester, students learn about RIS4E science from interactions with the RIS4E science team, through classroom visits, one-on-one interviews, and tours of laboratories. At the conclusion of the course, several students, along with a professor and a teaching assistant, join the RIS4E team during the field season. The journalism students observe the entire multi-day field campaign, from set-up, to data collection and analysis, and investigation of questions that arise as a result of field discoveries. They watch the scientists formulate and test hypotheses in real time. The field component for the 2017 RIS4E Science Journalism Program took journalism students to the Potrillo Volcanic Field in New Mexico for a 10-day field campaign. Student feedback was overwhelmingly positive. They gained experience

24 CFR 982.1 - Programs: purpose and structure.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Programs: purpose and structure. 982.1 Section 982.1 Housing and Urban Development Regulations Relating to Housing and Urban... § 982.1 Programs: purpose and structure. (a) General description. (1) In the HUD Housing Choice Voucher...

Comparison of phase composition, morphology and electrochemical property for Li3−xNaxV2(PO4)3 (x=0.5, 1.5 and 2.0) as lithium storage cathode materials

International Nuclear Information System (INIS)

Mao, Jinli; Shao, Lianyi; Li, Peng; Lin, Xiaoting; Shui, Miao; Long, Nengbing; Shu, Jie

2015-01-01

Graphical abstract: Display Omitted -- Highlights: •Li 3−x Na x V 2 (PO 4 ) 3 is prepared by a solid-state reaction method. •Li 2.5 Na 0.5 V 2 (PO 4 ) 3 is a three-phase mixture. •Both Li 1.5 Na 1.5 V 2 (PO 4 ) 3 and LiNa 2 V 2 (PO 4 ) 3 are two-phase composite. •Lithium ion diffusion coefficient is detected by cyclic voltammetry. •Structural change of LiNa 2 V 2 (PO 4 ) 3 is observed by in-situ XRD. -- Abstract: Three Li 3-x Na x V 2 (PO 4 ) 3 (x=0.5, 1.5 and 2.0) samples are synthesized by a traditional solid-state reaction method in this work. Their phase composition, surface morphology and electrochemical property are described and compared by using various physical/chemical methods. Phase analysis results reveal that Li 2.5 Na 0.5 V 2 (PO 4 ) 3 consists of monoclinic Li 3 V 2 (PO 4 ) 3 , rhombohedral Li 3 V 2 (PO 4 ) 3 and rhombohedral Na 3 V 2 (PO 4 ) 3. While, both Li 1.5 Na 1.5 V 2 (PO 4 ) 3 and LiNa 2 V 2 (PO 4 ) 3 are the two-phase mixture consisted of rhombohedral Li 3 V 2 (PO 4 ) 3 and rhombohedral Na 3 V 2 (PO 4 ) 3 . Electrochemical testing results reveal that LiNa 2 V 2 (PO 4 ) 3 and Li 1.5 Na 1.5 V 2 (PO 4 ) 3 can deliver the initial discharge capacities of 101.4 mAh g −1 and 108.6 mAh g −1 with a long potential plateau at 3.69 V, respectively. In contrast, Li 2.5 Na 0.5 V 2 (PO 4 ) 3 presents an initial discharge capacity of 111.7 mAh g −1 with four potential plateaus. High lithium ion diffusion coefficient in Li 2.5 Na 0.5 V 2 (PO 4 ) 3 indicates that the existence of monoclinic Li 3 V 2 (PO 4 ) 3 phase can improve the ionic conductivity and then be responsible for good electrochemical performance. Besides, in-situ X-ray diffraction observation of LiNa 2 V 2 (PO 4 ) 3 demonstrates that the phase transition is not fully reversible but quasi-reversible during the lithiation-delithiation process. The partial irreversibility of structural evolution for LiNa 2 V 2 (PO 4 ) 3 induces the capacity loss upon repeated cycles

Effect of dispersed SiO2 on the phase behaviour of NH4HSO4

Directory of Open Access Journals (Sweden)

Vargas, R. A.

2002-02-01

Full Text Available Phase equilibria and electrical conductivity of (1-xNH4HSO4-xSiO2 composites were studied by thermal and impedance measurements. Silica with particle size of 14 nm was used. The phase transitions of NH4HSO4 (AHS at 154 K and 420 K (melting point were not affected by the silica doping. No large changes in the low-temperature (T Estudiamos el equilibrio de fases y la conductividad eléctrica de las compositas (1-xNH4HSO4-xSiO2 por medidas térmicas y de impedancia. Se utilizaron partículas de silica de diámetro 14 nm. Las transiciones de fase del NH4HSO4 (AHS en 154 K y 420 K (punto de fusión no fueron afectadas con el dopaje de silica. No se observaron grandes cambios a bajas temperaturas (T < 420 K en la conductividad dc y la relajación eléctrica de las compositas al ser dopadas con silica. La parte imaginaria de la conductividad corregida (después de haber substraído la contribución de la conductividad dc, ε″(ω,T, como función de la frecuencia (f = ω/ 2π y la temperatura muestra un pico de dispersión alrededor de 1 MHz para pequeñas concentraciones de silica, cuya posición (fmax esta también térmicamente activada. Los resultados dieléctricos se discuten en términos del efecto de la polarización de las celdas sobre el movimiento de los protones.

Reversible Resistance Switching Effect in Amorphous Ge1Sb4Te7 Thin Films without Phase Transformation

International Nuclear Information System (INIS)

Hua-Jun, Sun; Li-Song, Hou; Yi-Qun, Wu; Xiao-Dong, Tang

2009-01-01

We demonstrate a reversible resistance switching effect that does not rely on amorphous-crystalline phase transformation in a nanoscale capacitor-like cell using Ge 1 Sb 4 Te 7 films as the working material. The polarity and amplitude of the applied electric voltage switches the cell resistance between low- and high-resistance states, as revealed in the current-voltage characteristics of the film by conductive atomic force microscopy (CAFM). This reversible SET/RESET switching effect is induced by voltage pulses and their polarity. The change of electrical resistance due to the switching effect is approximately two orders of magnitude

Sr3Fe5/4Mo3/4O6.9, an n = 2 Ruddlesen-Popper Phase: Synthesis and Properties

International Nuclear Information System (INIS)

Whaley, L.; Lobanov, M.; Sehptyakov, D.; Croft, M.; Ramanujachary, K.; Lofland, S.; Stephens, P.; Her, J.; Van Tendeloo, G.

2006-01-01

In a systematic search for an oxygen-stoichiometric phase, Sr 3 (FeMo)O 7 , in a range of iron-to-molybdenum ratios greater than 1:1 that typically give phase mixtures, we have found an n = 2 Ruddlesden-Popper phase, Sr 3 Fe 5/4 Mo 3/4 O 6.9 , as supported by synchrotron powder X-ray diffraction (SPXD), high-resolution transmission electron microscopy (HREM), and powder neutron diffraction (PND) results. By SPXD, this oxygen-deficient, B-site disordered, two-dimensional analogue of Sr2FeMoO6 adopts tetragonal I4/mmm symmetry (a = b = 3.92449(5) Angstroms; c = 20.3423(3) Angstroms) with vacancies at the O(1) oxygen site and with a composition that refines to a nominal stoichiometry Sr 3 Fe 5/4 Mo 3/4 O 6.9 . The two-phase SPXD refinement includes Sr 3 Fe 5/4 Mo 3/4 O 6.9 (95.7%) and a double-perovskite (DP) intergrowth, Sr 2 FeMoO 6 (4.3%), consistent with HREM studies in which DP intergrowths but no individual DP grains were found. The G-type antiferromagnetically (AFM)-ordered structure of the phase, with the magnetic cell a m = √2a ∼ 5.548 Angstroms, c m = c ∼ 20.35 Angstroms, derived from PND data, displays a saturated moment of 2.17(1) μ B at 9 K and an asynchronous decrease of the in-plane component of the Fe/Mo moment (μ xy ), with respect to the out-of-plane moment (μ z ) upon increasing temperature from 9 K up to the Neel temperature, TN ∼ 150 K. No structural transitions were observed over the entire temperature range studied: from 1.5 to 500 K. The temperature-dependent resistivity is consistent with Efros-Shklovskii variable-range hopping, applicable to two ranges of temperature (189 K RT ∼ 3 μ(Omega)·cm). A small negative magnetoresistance is observed (∼2.5%) at 5 T near the ordering temperature (∼150 K). The temperature-dependent magnetic susceptibility shows an inflection between 125 and 150 K, consistent with the AFM ordering temperature (∼150 K) observed by PND. X-ray near-edge spectroscopy data are consistent with formal

Near-term hybrid vehicle program, phase 1

Science.gov (United States)

1979-01-01

The preliminary design of a hybrid vehicle which fully meets or exceeds the requirements set forth in the Near Term Hybrid Vehicle Program is documented. Topics addressed include the general layout and styling, the power train specifications with discussion of each major component, vehicle weight and weight breakdown, vehicle performance, measures of energy consumption, and initial cost and ownership cost. Alternative design options considered and their relationship to the design adopted, computer simulation used, and maintenance and reliability considerations are also discussed.

Gas Phase Chromatography of some Group 4, 5, and 6 Halides

Energy Technology Data Exchange (ETDEWEB)

Sylwester, Eric Robert [Univ. of California, Berkeley, CA (United States)

1998-10-01

Gas phase chromatography using The Heavy Element Volatility Instrument (HEVI) and the On Line Gas Apparatus (OLGA III) was used to determine volatilities of ZrBr₄, HfBr₄, RfBr₄, NbBr₅, TaOBr₃, HaCl₅, WBr₆, FrBr, and BiBr₃. Short-lived isotopes of Zr, Hf, Rf, Nb, Ta, Ha, W, and Bi were produced via compound nucleus reactions at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory and transported to the experimental apparatus using a He gas transport system. The isotopes were halogenated, separated from the other reaction products, and their volatilities determined by isothermal gas phase chromatography. Adsorption Enthalpy (ΔH_a) values for these compounds were calculated using a Monte Carlo simulation program modeling the gas phase chromatography column. All bromides showed lower volatility than molecules of similar molecular structures formed as chlorides, but followed similar trends by central element. Tantalum was observed to form the oxybromide, analogous to the formation of the oxychloride under the same conditions. For the group 4 elements, the following order in volatility and ΔH_a was observed: RfBr₄ > ZrBr₄ > HfBr₄. The ΔH_a values determined for the group 4, 5, and 6 halides are in general agreement with other experimental data and theoretical predictions. Preliminary experiments were performed on Me-bromides. A new measurement of the half-life of ²⁶¹Rf was performed. ²⁶¹Rf was produced via the ²⁴⁸Cm(¹⁸O, 5n) reaction and observed with a half-life of 74_-6⁺⁷ seconds, in excellent agreement with the previous measurement of 78_-6⁺¹¹ seconds. We recommend a new half-life of 75±7 seconds for ²⁶¹Rf based on these two measurements. Preliminary studies in transforming HEVI from an isothermal (constant

Conductivity, calorimetry and phase diagram of the NaHSO4–KHSO4 system

DEFF Research Database (Denmark)

Hind, Hamma-Cugny; Rasmussen, Søren Birk; Rogez, J.

2006-01-01

to polynomials of the form κ(X)=A(X)+B(X)(T-Tm)+C(X)(T-Tm)2, where Tm is the intermediate temperature of the measured temperature range and X, the mole fraction of KHSO4. The possible role of this binary system as a catalyst solvent is also discussed. (C) 2005 Elsevier B.V. All rights reserved.......Physico-chemical properties of the binary system NaHSO4-KHSO4 were studied by calorimetry and conductivity, The enthalpy of mixing has been measured at 505 K in the full composition range and the phase diagram calculated. The phase diagram has also been constructed from phase transition...

Infinite statistics and the SU(1, 1) phase operator

International Nuclear Information System (INIS)

Gerry, Christopher C

2005-01-01

A few years ago, Agarwal (1991 Phys. Rev. A 44 8398) showed that the Susskind-Glogower phase operators, expressible in terms of Bose operators, provide a realization of the algebra for particles obeying infinite statistics. In this paper we show that the SU(1, 1) phase operators, constructed in terms of the elements of the su(1, 1) Lie algebra, also provide a realization of the algebra for infinite statistics. There are many realizations of the su(1, 1) algebra in terms of single or multimode bose operators, three of which are discussed along with their corresponding phase states. The Susskind-Glogower phase operator is a special case of the SU(1, 1) phase operator associated with the Holstein-Primakoff realization of su(1, 1). (letter to the editor)

Hypersonic ramjet experiment project. Phase 1: Computer program description, ramjet and scramjet cycle performance

Science.gov (United States)

Jackson, R. J.; Wang, T. T.

1974-01-01

A computer program was developed to describe the performance of ramjet and scramjet cycles. The program performs one dimensional calculations of the equilibrium, real-gas internal flow properties of the engine. The program can be used for the following: (1) preliminary design calculation and (2) design analysis of internal flow properties corresponding to stipulated flow areas. Only the combustion of hydrogen in air is considered in this case.