Material-balance assessment of the New Albany-Chesterian petroleum system of the Illinois basin

Science.gov (United States)

Lewan, M.D.; Henry, M.E.; Higley, D.K.; Pitman, Janet K.

2002-01-01

The New Albany-Chesterian petroleum system of the Illinois basin is a well-constrained system from which petroleum charges and losses were quantified through a material-balance assessment. This petroleum system has nearly 90,000 wells penetrating the Chesterian section, a single New Albany Shale source rock accounting for more than 99% of the produced oil, well-established stratigraphic and structural frameworks, and accessible source rock samples at various maturity levels. A hydrogen index (HI) map based on Rock-Eval analyses of source rock samples of New Albany Shale defines the pod of active source rock and extent of oil generation. Based on a buoyancy-drive model, the system was divided into seven secondary-migration catchments. Each catchment contains a part of the active pod of source rock from which it derives a petroleum charge, and this charge is confined to carrier beds and reservoirs within these catchments as accountable petroleum, petroleum losses, or undiscovered petroleum. A well-constrained catchment with no apparent erosional or leakage losses is used to determine an actual petroleum charge from accountable petroleum and residual migration losses. This actual petroleum charge is used to calibrate the other catchments in which erosional petroleum losses have occurred. Petroleum charges determined by laboratory pyrolysis are exaggerated relative to the actual petroleum charge. Rock-Eval charges are exaggerated by a factor of 4-14, and hydrouspyrolysis charges are exaggerated by a factor of 1.7. The actual petroleum charge provides a more meaningful material balance and more realistic estimates of petroleum losses and remaining undiscovered petroleum. The total petroleum charge determined for the New Albany-Chesterian system is 78 billion bbl, of which 11.4 billion bbl occur as a accountable in place petroleum, 9 billion bbl occur as residual migration losses, and 57.6 billion bbl occur as erosional losses. Of the erosional losses, 40 billion bbl

Source rock potential of middle cretaceous rocks in Southwestern Montana

Science.gov (United States)

Dyman, T.S.; Palacas, J.G.; Tysdal, R.G.; Perry, W.J.; Pawlewicz, M.J.

1996-01-01

The middle Cretaceous in southwestern Montana is composed of a marine and nonmarine succession of predominantly clastic rocks that were deposited along the western margin of the Western Interior Seaway. In places, middle Cretaceous rocks contain appreciable total organic carbon (TOC), such as 5.59% for the Mowry Shale and 8.11% for the Frontier Formation in the Madison Range. Most samples, however, exhibit less than 1.0% TOC. The genetic or hydrocarbon potential (S1+S2) of all the samples analyzed, except one, yield less than 1 mg HC/g rock, strongly indicating poor potential for generating commercial amounts of hydrocarbons. Out of 51 samples analyzed, only one (a Thermopolis Shale sample from the Snowcrest Range) showed a moderate petroleum potential of 3.1 mg HC/g rock. Most of the middle Cretaceous samples are thermally immature to marginally mature, with vitrinite reflectance ranging from about 0.4 to 0.6% Ro. Maturity is high in the Pioneer Mountains, where vitrinite reflectance averages 3.4% Ro, and at Big Sky Montana, where vitrinite reflectance averages 2.5% Ro. At both localities, high Ro values are due to local heat sources, such as the Pioneer batholith in the Pioneer Mountains.

An experimental investigation of geochromatography during secondary migration of petroleum performed under subsurface conditions with a real rock

Directory of Open Access Journals (Sweden)

Larter Steve

2000-10-01

Full Text Available An understanding of the size of petroleum secondary migration systems is vital for successful exploration for petroleum reserves. Geochemists have suggested that compositional fractionation of petroleum accompanying the migration process (geochromatography can potentially be used to infer distances petroleum may have travelled and the ratio of oil in the reservoir to that lost in the carrier. To date, this has been attempted by measuring concentrations and distributions of specific steranes, and aromatic oxygen and nitrogen compounds in reservoired oils which have been proposed to respond to migration rather than to source maturity or other effects. We report here an experiment involving oil migration through an initially water wet siltstone under realistic subsurface carrier bed or reservoir conditions (48 MPa, 70°C where source facies and maturity effects are eliminated. We show that geochromatography does indeed occur even for initially water-saturated rocks and that the migration fractionations observed for alkylcarbazoles, benzocarbazoles and alkylphenols are very similar to those seen in field data sets. In contrast, sterane based migration parameters show no compositional fractionation under these conditions.

Organic compositions of lacustrine source rocks in Jiyang super-depression and its implication to petroleum geology

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The compositions of organic matter in four immature source rocks from Tertiary strata of Jiyang super-depression, the most typical continental rift subsidence basin in East China, have been studied by different extracting methods with CHCl3, MAC and CS2/NMP, respectively. The results suggest that there are great differences among the chemical compositions of organic matter in the source rocks derived from different depositional environments. About 79% of all the organic matter exists by non- covalent bond in the Es4 source rocks which were deposited under the saline lacustrine, indicating that its organic matter is not the real kerogen, but mainly composed of soluble organic matter which is easy to generate hydrocarbon at lower temperature. This is why the immature oils were derived from Es4 source rocks in Dongying depression. In contrast, around 60% of organic matter exists by covalent bond in Es3 source rocks which were deposited under the deep brackish-fresh lacustrine, showing that Es3 source rocks are mainly composed of kerogen producing mature hydrocarbon at higher temperature. The thermal simulation experiments, upon the remaining solid source rocks which were sequentially extracted by the three solvents, have been carried out. The chloroform extracts from the simulation product have been compared with the other three solvent extracts gained at room temperature. It is obvious that remarkable odd/even predominance (OEP) is mainly the characteristic of soluble organic matter; phytane mostly exists in the soluble organic matter by means of non-covalent bonds and characteristics of soluble organic matter are similar to these in immature oils produced in Jiyang super-depression.

Geochemistry of crude oils, seepage oils and source rocks from Belize and Guatemala

DEFF Research Database (Denmark)

Petersen, H.I.; Holland, B.; Nytoft, H.P.

2012-01-01

This study reviews the stratigraphy and the poorly documented petroleum geology of the Belize-Guatemala area in northern Central America. Guatemala is divided by the east-west trending La Libertad arch into the North and South Petén Basins. The arch is the westward continuation of the Maya...... generated from source rocks with similar thermal maturities. The crude oils were generated from marine carbonate source rocks and could be divided into three groups: Group 1 oils come from the North Petén Basin (Guatemala) and the western part of the Corozal Basin (Belize), and have a typical carbonate...

Petroleum geochemical responses to reservoir rock properties

Energy Technology Data Exchange (ETDEWEB)

Bennett, B.; Larter, S.R. [Calgary Univ., AB (Canada)

2008-07-01

Reservoir geochemistry is used to study petroleum basin development, petroleum mixing, and alterations. In this study, polar non-hydrocarbons were used as proxies for describing reservoir properties sensitive to fluid-rock interactions. A core flood experiment was conducted on a Carboniferous siltstone core obtained from a site in the United Kingdom. Core samples were then obtained from a typical upper shoreface in a North Sea oilfield. The samples were extracted with a dichloromethane and methanol mixture. Alkylcarbazoles and alkylfluorenones were then isolated from the samples. Compositional changes along the core were also investigated. Polar non hydrocarbons were studied using a wireline gamma ray log. The strongest deflections were observed in the basal coarsening upwards unit. The study demonstrated the correlations between molecular markers, and indicated that molecular parameters can be used to differentiate between clean sand units and adjacent coarsening upward muddy sand sequences. It was concluded that reservoir geochemical parameters can provide an independent response to properties defined by petrophysical methods. 6 refs., 2 figs.

Petroleum coke as energy source: an update

International Nuclear Information System (INIS)

Pinelli, G.

2008-01-01

A previous review presented a critical evaluation of the use of petroleum coke as energy source. After some years, with reference to increased petroleum coke production, that paper is revised. In particular, the attention is now focused on world petroleum coke market trends and, in regard to petroleum coke used as fuel, on new Italian environment laws. [it

Source rock potential of the organic rich Turonian - Upper Campanian carbonates of northern Lebanon

Energy Technology Data Exchange (ETDEWEB)

Daher, S. Bou; Littke, R. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Nader, F.H. [IFP Energies nouvelles, Paris (France). Dept. of Sedimentology-Stratigraphy

2013-08-01

Upper Cretaceous chalks, marls, and shales are arguably the most prolific petroleum source rocks in the eastern Mediterranean region. 209 core samples from the Turonian - Upper Campanian rock succession in north Lebanon were collected and analyzed for their organic matter (OM) content, quality, and maturity. The total organic carbon (TOC) measurements revealed a very good source rock potential for a 150 m interval within the Upper Santonian - Upper Campanian, with an average of 2% TOC. High HI values (average 707 mg/g TOC) characterize these source rocks as type I kerogen and reflect a very good preservation of the organic matter. T{sub max} values (average 421 C) match the other maturity parameters such as vitrinite reflectance (average 0.35%), and all point towards immature organic matter. The equivalent Upper Cretaceous in the offshore Levant basin has enough overburden to have reached maturity. However, the accurate extrapolation of the organic matter quality and quantity to the offshore is yet a challenge with the data at hand. (orig.)

Evaluation of kinetic uncertainty in numerical models of petroleum generation

Science.gov (United States)

Peters, K.E.; Walters, C.C.; Mankiewicz, P.J.

2006-01-01

Oil-prone marine petroleum source rocks contain type I or type II kerogen having Rock-Eval pyrolysis hydrogen indices greater than 600 or 300-600 mg hydrocarbon/g total organic carbon (HI, mg HC/g TOC), respectively. Samples from 29 marine source rocks worldwide that contain mainly type II kerogen (HI = 230-786 mg HC/g TOC) were subjected to open-system programmed pyrolysis to determine the activation energy distributions for petroleum generation. Assuming a burial heating rate of 1??C/m.y. for each measured activation energy distribution, the calculated average temperature for 50% fractional conversion of the kerogen in the samples to petroleum is approximately 136 ?? 7??C, but the range spans about 30??C (???121-151??C). Fifty-two outcrop samples of thermally immature Jurassic Oxford Clay Formation were collected from five locations in the United Kingdom to determine the variations of kinetic response for one source rock unit. The samples contain mainly type I or type II kerogens (HI = 230-774 mg HC/g TOC). At a heating rate of 1??C/m.y., the calculated temperatures for 50% fractional conversion of the Oxford Clay kerogens to petroleum differ by as much as 23??C (127-150??C). The data indicate that kerogen type, as defined by hydrogen index, is not systematically linked to kinetic response, and that default kinetics for the thermal decomposition of type I or type II kerogen can introduce unacceptable errors into numerical simulations. Furthermore, custom kinetics based on one or a few samples may be inadequate to account for variations in organofacies within a source rock. We propose three methods to evaluate the uncertainty contributed by kerogen kinetics to numerical simulations: (1) use the average kinetic distribution for multiple samples of source rock and the standard deviation for each activation energy in that distribution; (2) use source rock kinetics determined at several locations to describe different parts of the study area; and (3) use a weighted

Hydrodynamic thickness of petroleum oil adsorbed layers in the pores of reservoir rocks.

Science.gov (United States)

Alkafeef, Saad F; Algharaib, Meshal K; Alajmi, Abdullah F

2006-06-01

The hydrodynamic thickness delta of adsorbed petroleum (crude) oil layers into the pores of sandstone rocks, through which the liquid flows, has been studied by Poiseuille's flow law and the evolution of (electrical) streaming current. The adsorption of petroleum oil is accompanied by a numerical reduction in the (negative) surface potential of the pore walls, eventually stabilizing at a small positive potential, attributed to the oil macromolecules themselves. After increasing to around 30% of the pore radius, the adsorbed layer thickness delta stopped growing either with time or with concentrations of asphaltene in the flowing liquid. The adsorption thickness is confirmed with the blockage value of the rock pores' area determined by the combination of streaming current and streaming potential measurements. This behavior is attributed to the effect on the disjoining pressure across the adsorbed layer, as described by Derjaguin and Churaev, of which the polymolecular adsorption films lose their stability long before their thickness has approached the radius of the rock pore.

Review of oil families and their petroleum systems of the Williston Basin

Science.gov (United States)

Lillis, Paul G.

2013-01-01

The petroleum system concept was first applied in 1974 (Dow/Williams) to identify three oil systems in the Williston Basin, and recent studies have expanded the number to at least nine. This paper reviews the petroleum geochemistry, oil-oil, and oil-source correlations of the oil systems of the Williston Basin, providing a new perspective and some new findings. Petroleum systems with a known source (documented oil-source correlation) include the Red River (Ordovician), Winnipegosis (Devonian), Bakken (Devonian-Mississippian), Madison (Mississippian), and Tyler (Pennsylvanian) systems. Petroleum systems with an identified source rock but no documented oil-source correlation are considered hypothetical and include the Winnipeg (Ordovician), Duperow (Devonian), and Birdbear (Devonian). The Deadwood (Cambrian-Ordovician) petroleum system is speculative because a good oil-prone source rock has not been identified. The stratigraphic distribution of the oil families from each system is generally limited to the same formation from which they were sourced due to efficient seals and a paucity of vertical migration pathways, but some notable exceptions do occur.

Evaluation of the quality, thermal maturity and distribution of potential source rocks in the Danish part of the Norwegian–Danish Basin

Directory of Open Access Journals (Sweden)

Kristensen, Lars

2008-11-01

Full Text Available The quality, thermal maturity and distribution of potential source rocks within the Palaeozoic–Mesozoic succession of the Danish part of the Norwegian–Danish Basin have been evaluated on the basis of screening data from over 4000 samples from the pre-Upper Cretaceous succession in 33 wells. The Lower Palaeozoic in the basin is overmature and the Upper Cretaceous – Cenozoic strata have no petroleum generation potential, but the Toarcian marine shales of the Lower Jurassic Fjerritslev Formation (F-III, F-IV members and the uppermost Jurassic – lowermost Cretaceous shales of the Frederikshavn Formation may qualify as potential source rocks in parts of the basin. Neither of these potential source rocks has a basinwide distribution; the present occurrence of the Lower Jurassic shales was primarily determined by regional early Middle Jurassic uplift and erosion. The generation potential of these source rocks is highly variable. The F-III and F-IV members show significant lateral changes in generation capacity, the best-developed source rocks occurring in the basin centre. The combined F-III andF-IV members in the Haldager-1, Kvols-1 and Rønde-1 wells contain ‘net source-rock’ thicknesses (cumulative thickness of intervals with Hydrogen Index (HI >200 mg HC/g TOC of 40 m, 83 m, and 92 m, respectively, displaying average HI values of 294, 369 and 404 mg HC/g TOC. The Mors-1 well contains 123 m of ‘net source rock’ with an average HI of 221 mg HC/g TOC. Parts of the Frederikshavn Formation possess a petroleum generation potential in the Hyllebjerg-1, Skagen-2, Voldum-1 and Terne-1 wells, the latter well containing a c.160 m thick highly oil-prone interval with an average HI of 478 mg HC/g TOC and maximum HI values >500 mg HC/g TOC. The source-rock evaluation suggests that a Mesozoic petroleum system is the most likely in the study area. Two primary plays are possible: (1 the Upper Triassic – lowermost Jurassic Gassum play, and (2the

Geology and oil and gas assessment of the Mancos-Menefee Composite Total Petroleum System: Chapter 4 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Condon, S.M.; Hatch, J.R.

2013-01-01

The Mancos-Menefee Composite Total Petroleum System (TPS) includes all genetically related hydrocarbons generated from organic-rich shales in the Cretaceous Mancos Shale and from carbonaceous shale, coal beds, and humate in the Cretaceous Menefee Formation of the Mesaverde Group. The system is called a composite total petroleum system because the exact source of the hydrocarbons in some of the reservoirs is not known. Reservoir rocks that contain hydrocarbons generated in Mancos and Menefee source beds are found in the Cretaceous Dakota Sandstone, at the base of the composite TPS, through the lower part of the Cliff House Sandstone of the Mesaverde Group, at the top. Source rocks in both the Mancos Shale and Menefee Formation entered the oil generation window in the late Eocene and continued to generate oil or gas into the late Miocene. Near the end of the Miocene in the San Juan Basin, subsidence ceased, hydrocarbon generation ceased, and the basin was uplifted and differentially eroded. Reservoirs are now underpressured.

Geologic characterization of Cuvette Centrale petroleum systems Congo-DRC

Energy Technology Data Exchange (ETDEWEB)

Vicentelli, Maria Gabriela C.; Barbosa, Mauro; Rezende, Nelio G.A.M. [HRT Petroleum, Rio de Janeiro, RJ (Brazil)

2008-07-01

The Cuvette Centrale is an almost unexplored basin, which contains some petroleum system elements that indicate the presence of hydrocarbons. In this sense; this paper presents an exploratory alternative for this intracratonic basin. The interpretation of the limited gravimetric, magnetometric, geochemical and seismic available data allowed the identification of many huge structural features and also some areas with hydrocarbon potential for stratigraphic traps. The presence of several oil and gas seeps widespread around the Busira and Lokoro sub-basins indicate that at least one active petroleum system exist in the basin. Despite only four wells have been drilled in the basin, one of them presented oil shows during drilling. Geological correlations between Brazilian Paleozoic basins and Cuvette Centrale sedimentary sequences permitted to conclude that Cambro-Ordovician and Siluro-Devonian source rocks must be present and active in the Cuvette Centrale basin. The tectono-stratigraphic evolution history of the Cuvette Centrale from Neo proterozoic to Recent times shows extensional and compressional/transpressional alternating phases along the geological time. The most confident petroleum system expected in the Cuvette Centrale is characterized by the Cambrian Mamungi shale - source rock - and the Cambro-Ordovician. Upper Arenaceous Sequence - reservoirs, as observed in the MBandaka and Gilson wells and confirmed by surface geology in outcrops. Besides, other potential petroleum systems are expected to occur in the basin. One is characterized by the Neo proterozoic Itury Group source rock and reservoirs in the mature/over mature stage, the others are the Siluro-Devonian and Cretaceous source rocks and reservoirs, expected to occur with better maturity conditions only in the deeper parts of the basin. (author)

Source rock

Directory of Open Access Journals (Sweden)

Abubakr F. Makky

2014-03-01

Full Text Available West Beni Suef Concession is located at the western part of Beni Suef Basin which is a relatively under-explored basin and lies about 150 km south of Cairo. The major goal of this study is to evaluate the source rock by using different techniques as Rock-Eval pyrolysis, Vitrinite reflectance (%Ro, and well log data of some Cretaceous sequences including Abu Roash (E, F and G members, Kharita and Betty formations. The BasinMod 1D program is used in this study to construct the burial history and calculate the levels of thermal maturity of the Fayoum-1X well based on calibration of measured %Ro and Tmax against calculated %Ro model. The calculated Total Organic Carbon (TOC content from well log data compared with the measured TOC from the Rock-Eval pyrolysis in Fayoum-1X well is shown to match against the shale source rock but gives high values against the limestone source rock. For that, a new model is derived from well log data to calculate accurately the TOC content against the limestone source rock in the study area. The organic matter existing in Abu Roash (F member is fair to excellent and capable of generating a significant amount of hydrocarbons (oil prone produced from (mixed type I/II kerogen. The generation potential of kerogen in Abu Roash (E and G members and Betty formations is ranging from poor to fair, and generating hydrocarbons of oil and gas prone (mixed type II/III kerogen. Eventually, kerogen (type III of Kharita Formation has poor to very good generation potential and mainly produces gas. Thermal maturation of the measured %Ro, calculated %Ro model, Tmax and Production index (PI indicates that Abu Roash (F member exciting in the onset of oil generation, whereas Abu Roash (E and G members, Kharita and Betty formations entered the peak of oil generation.

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1997-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

A Study of Porphyrins in Petroleum Source Rocks

Energy Technology Data Exchange (ETDEWEB)

Huseby, Berit

1996-12-31

This thesis discusses several aspects of porphyrin geochemistry. Degradation experiments have been performed on the Messel oil shale (Eocene, Germany) to obtain information on porphyrins bound or incorporated into macromolecular structures. Thermal heating of the preextracted kerogen by hydrous pyrolysis was used to study the release of porphyrins and their temperature dependent changes during simulated diagenesis and catagenesis. Selective chemical degradation experiments were performed on the preextracted sediment to get more detailed information about porphyrins that are specifically bound to the macromolecular structures via ester bonds. From the heating experiments, in a separate study, the porphyrin nitrogen content in the generated bitumens was compared to the bulk of organic nitrogen compounds in the fraction. The bulk nitrogen contents in the generated bitumens, the water phase and the residual organic matter was recorded to establish the distribution of nitrogen between the kerogen and product phases. Porphyrins as biomarkers were examined in naturally matured Kimmeridge clay source rocks (Upper Jurassic, Norway), and the use of porphyrins as general indicators of maturity was evaluated. Underlying maturity trends in the biomarker data was investigated by Partial Least Squares analysis. Porphyrin as indicators of depositional conditions was also addressed, where the correlations between the (amounts) abundance of nickel and vanadyl porphyrins were mapped together with other descriptors that are assumed to be indicative of redox depositional conditions. 252 refs., 28 figs., 4 tabs.

Methods for differentiating identity and sources of mixed petroleum pollutants in the environment

International Nuclear Information System (INIS)

Kaplan, I.R.; Alimi, H.; Lee, R.P.

1993-01-01

When crude or refined oil products enter the environment they begin to degrade by numerous microbiological or physical processes. The result of such changes is to alter the molecular composition of the product so that its source is unrecognizable by application of conventional EPA-type methodology. Numerous methods have been devised in the petroleum exploration industry to characterize source rock bitumens and reservoir hydrocarbons. A modification of these methods has been successfully applied at the authors company to identify the source of the fugitive hydrocarbons. For mildly altered products a statistical comparison is made using pattern recognition of the n-alkane distribution between C 10 -C 35 for heavy products and C 3 -C 10 for the gasoline range products. For highly altered products, a search is made for complex organic molecules that have undergone the least alteration, which include long chain polynuclear aromatic hydrocarbons and the polycyclic paraffinic hydrocarbons. These biomarker compounds have many isomeric forms which help characterize their sources. Elemental composition; especially sulfur, vanadium and nickel, and other transition and base metals help differentiate crude oil from refined products. Lead alkyls and MTBE are especially useful in determining residence time of gasoline products in soil and ground water. Petroporphyrin characterization can help differentiate crude oil from heavy refined oils or fluids. Stable isotope ratios are particularly useful for differentiating sources of highly altered petroleum products

Egret-Hibernia(!), a significant petroleum system, northern Grand Banks area, offshore eastern Canada

Science.gov (United States)

Magoon, L.B.; Hudson, T.L.; Peters, K.E.

2005-01-01

Egret-Hibernia(!) is a well-explored petroleum system (3.25 billion barrels oil equivalent [BOE]) located in the Jeanne d'Arc Basin on the Labrador - Newfoundland shelf. Rifting and sediment fill began in the Late Triassic. Egret source rock was deposited in the Late Jurassic at about 153 Ma. After this time, alternating reservoir rock and seal rock were deposited with some syndepositional faulting. By the end of the Early Cretaceous, faults and folds had formed numerous structural traps. For the next 100 m.y., overburden rock thermally matured the source rock when it reached almost 4 km (2.5 mi) burial depth. For 2 km (1.25 mi) below this depth, oil and gas were expelled, until the source was depleted. The expelled petroleum migrated updip to nearby faulted, anticlinal traps, where much of it migrated across faults and upsection to the Hibernia Formation (44% recoverable oil) and Avalon Formation (28%). Accumulation size decreased, and gas content increased from west to east, independent of trap size. These changes correspond to a decrease in source rock richness and quality from west to east. Almost all (96%) of the discovered petroleum resides in the Lower Cretaceous or older reservoir rock units. All accumulations found to date are normally pressured in structural traps. Fifty-two exploration wells found eighteen discoveries. Their size ranges from 1.2 to 0.01 billion BOE. Most discoveries were made between 1979 and 1991. The discovery cycle began with larger accumulations and progressed to smaller accumulations. The estimated sizes of the larger accumulations have grown since 1990. Estimated mean value for undiscovered hydrocarbons is 3.8 billion BOE, thereby raising the ultimate size of Egret-Hibernia(!) to 6.19 billion BOE. Copyright ?? 2005. The American Association of Petroleum Geologists. All rights reserved.

The Chuar Petroleum System, Arizona and Utah

Science.gov (United States)

Lillis, Paul G.

2016-01-01

The Neoproterozoic Chuar Group consists of marine mudstone, sandstone and dolomitic strata divided into the Galeros and Kwagunt Formations, and is exposed only in the eastern Grand Canyon, Arizona. Research by the U.S. Geological Survey (USGS) in the late 1980s identified strata within the group to be possible petroleum source rocks, and in particular the Walcott Member of the Kwagunt Formation. Industry interest in a Chuar oil play led to several exploratory wells drilled in the 1990s in southern Utah and northern Arizona to test the overlying Cambrian Tapeats Sandstone reservoir, and confirm the existence of the Chuar in subcrop. USGS geochemical analyses of Tapeats oil shows in two wells have been tentatively correlated to Chuar bitumen extracts. Distribution of the Chuar in the subsurface is poorly constrained with only five well penetrations, but recently published gravity/aeromagnetic interpretations provide further insight into the Chuar subcrop distribution. The Chuar petroleum system was reexamined as part of the USGS Paradox Basin resource assessment in 2011. A map was constructed to delineate the Chuar petroleum system that encompasses the projected Chuar source rock distribution and all oil shows in the Tapeats Sandstone, assuming that the Chuar is the most likely source for such oil shows. Two hypothetical plays were recognized but not assessed: (1) a conventional play with a Chuar source and Tapeats reservoir, and (2) an unconventional play with a Chuar source and reservoir. The conventional play has been discouraging because most surface structures have been tested by drilling with minimal petroleum shows, and there is some evidence that petroleum may have been flushed by CO2 from Tertiary volcanism. The unconventional play is untested and remains promising even though the subcrop distribution of source facies within the Chuar Group is largely unknown.

A chemical and thermodynamic model of oil generation in hydrocarbon source rocks

Science.gov (United States)

Helgeson, Harold C.; Richard, Laurent; McKenzie, William F.; Norton, Denis L.; Schmitt, Alexandra

2009-02-01

Thermodynamic calculations and Gibbs free energy minimization computer experiments strongly support the hypothesis that kerogen maturation and oil generation are inevitable consequences of oxidation/reduction disproportionation reactions caused by prograde metamorphism of hydrocarbon source rocks with increasing depth of burial.These experiments indicate that oxygen and hydrogen are conserved in the process.Accordingly, if water is stable and present in the source rock at temperatures ≳25 but ≲100 °C along a typical US Gulf Coast geotherm, immature (reduced) kerogen with a given atomic hydrogen to carbon ratio (H/C) melts incongruently with increasing temperature and depth of burial to produce a metastable equilibrium phase assemblage consisting of naphthenic/biomarker-rich crude oil, a type-II/III kerogen with an atomic hydrogen/carbon ratio (H/C) of ˜1, and water. Hence, this incongruent melting process promotes diagenetic reaction of detritus in the source rock to form authigenic mineral assemblages.However, in the water-absent region of the system CHO (which is extensive), any water initially present or subsequently entering the source rock is consumed by reaction with the most mature kerogen with the lowest H/C it encounters to form CO 2 gas and a new kerogen with higher H/C and O/C, both of which are in metastable equilibrium with one another.This hydrolytic disproportionation process progressively increases both the concentration of the solute in the aqueous phase, and the oil generation potential of the source rock; i.e., the new kerogen can then produce more crude oil.Petroleum is generated with increasing temperature and depth of burial of hydrocarbon source rocks in which water is not stable in the system CHO by a series of irreversible disproportionation reactions in which kerogens with higher (H/C)s melt incongruently to produce metastable equilibrium assemblages consisting of crude oil, CO 2 gas, and a more mature (oxidized) kerogen with a lower

Biomarker fingerprinting : application and limitations for source identification and correlation of oils and petroleum products

International Nuclear Information System (INIS)

Wang, Z.; Fingas, M.F.; Yang, C.; Hollebone, B.

2004-01-01

Biological markers or biomarkers are complex molecules originating from formerly living organisms. They are among the most important hydrocarbon groups in petroleum because every crude oil exhibits an essentially unique biomarker or fingerprint due to the wide variety of geological conditions under which oil is formed. When found in crude oils, rocks and sediments, biomarkers have the same structures as their parent organic molecules. Therefore, chemical analysis of source-characteristic and environmentally persistent biomarkers can provide valuable information in determining the source of spilled oil. Biomarkers can also be used to differentiate oils and to monitor the degradation process and the weathering state of oils under a range of conditions. The use of biomarker techniques to study oil spills has increased significantly in recent years. This paper provided case studies to demonstrate: (1) biomarker distribution in weathered oil and in petroleum products with similar chromatographic profiles, (2) sesquiterpenes and diamondoid biomarkers in oils and light petroleum products, (3) unique biomarker compounds in oils, (4) diagnostic ratios of biomarkers, and (5) biodegradation of biomarkers. It was noted that the trend to use biomarkers to study oil spills will continue. Continuous advances in analytical methods will further improve the application of oil hydrocarbon fingerprinting for environmental studies. 36 refs., 5 tabs., 12 figs

Petroleum geological features and exploration prospect of deep marine carbonate rocks in China onshore: A further discussion

Directory of Open Access Journals (Sweden)

Zhao Wenzhi

2014-10-01

Full Text Available Deep marine carbonate rocks have become one of the key targets of onshore oil and gas exploration and development for reserves replacement in China. Further geological researches of such rocks may practically facilitate the sustainable, steady and smooth development of the petroleum industry in the country. Therefore, through a deep investigation into the fundamental geological conditions of deep marine carbonate reservoirs, we found higher-than-expected resource potential therein, which may uncover large oil or gas fields. The findings were reflected in four aspects. Firstly, there are two kinds of hydrocarbon kitchens which were respectively formed by conventional source rocks and liquid hydrocarbons cracking that were detained in source rocks, and both of them can provide large-scale hydrocarbons. Secondly, as controlled by the bedding and interstratal karstification, as well as the burial and hydrothermal dolomitization, effective carbonate reservoirs may be extensively developed in the deep and ultra-deep strata. Thirdly, under the coupling action of progressive burial and annealing heating, some marine source rocks could form hydrocarbon accumulations spanning important tectonic phases, and large quantity of liquid hydrocarbons could be kept in late stage, contributing to rich oil and gas in such deep marine strata. Fourthly, large-scale uplifts were formed by the stacking of multi-episodic tectonism and oil and gas could be accumulated in three modes (i.e., stratoid large-area reservoir-forming mode of karst reservoirs in the slope area of uplift, back-flow type large-area reservoir-forming mode of buried hill weathered crust karst reservoirs, and wide-range reservoir-forming mode of reef-shoal reservoirs; groups of stratigraphic and lithologic traps were widely developed in the areas of periclinal structures of paleohighs and continental margins. In conclusion, deep marine carbonate strata in China onshore contain the conditions for

Total petroleum systems of the Pelagian Province, Tunisia, Libya, Italy, and Malta; the Bou Dabbous, Tertiary and Jurassic-Cretaceous composite

Science.gov (United States)

Klett, T.R.

2001-01-01

Undiscovered conventional oil and gas resources were assessed within total petroleum systems of the Pelagian Province (2048) as part of the U.S. Geological Survey World Petroleum Assessment 2000. The Pelagian Province is located mainly in eastern Tunisia and northwestern Libya. Small portions of the province extend into Malta and offshore Italy. Although several petroleum systems may exist, only two ?composite? total petroleum systems were identified. Each total petroleum system comprises a single assessment unit. These total petroleum systems are called the Bou Dabbous?Tertiary and Jurassic-Cretaceous Composite, named after the source-rock intervals and reservoir-rock ages. The main source rocks include mudstone of the Eocene Bou Dabbous Formation; Cretaceous Bahloul, Lower Fahdene, and M?Cherga Formations; and Jurassic Nara Formation. Known reservoirs are in carbonate rocks and sandstone intervals throughout the Upper Jurassic, Cretaceous, and Tertiary sections. Traps for known accumulations include fault blocks, low-amplitude anticlines, high-amplitude anticlines associated with reverse faults, wrench fault structures, and stratigraphic traps. The estimated means of the undiscovered conventional petroleum volumes in total petroleum systems of the Pelagian Province are as follows: [MMBO, million barrels of oil; BCFG, billion cubic feet of gas; MMBNGL, million barrels of natural gas liquids] Total Petroleum System MMBO BCFG MMBNGL Bou Dabbous?Tertiary 667 2,746 64 Jurassic-Cretaceous Composite 403 2,280 27

Depositional environment and source rock potential of Cenomanian and Turonian sedimentary rocks of the Tarfaya Basin, Southwest Morocco

Energy Technology Data Exchange (ETDEWEB)

Ghassal, B.I.; Littke, R.; Sachse, V.; Sindern, S.; Schwarzbauer, J.

2016-07-01

from bituminite-fair to bituminite-rich and to higher percentages of visible organic matter towards the younger interval. These differences in the organic matter type are attributed to i) early diagenetic kerogen sulfurization and ii) the upwelling depositional environment. Moreover, kerogen sulfurization was controlled by the relationship between carbonate, iron and sulfur as well as the organic matter. Thus, the organic carbon-rich deposits can be grouped into: i) low Sorg and moderately organic matter-rich oil prone source rocks, ii) moderate Sorg and organic-carbon-rich oil prone source rocks, iii) high Sorg and organic carbon-rich oil prone source rocks and iv) very high Sorg and organic carbon-rich oil prone source rocks, the latter representing the CTBE interval. Types 2 to 4 will generate sulfur-rich petroleum upon maturation or artificial oil shale retorting. This integrated organic and inorganic approach sheds light on the various processes leading to the development of the world-class oil shales deposited through the Cenomanian to Turonian. In addition, this study shows how the changes in the depositional environment might have controlled kerogen sulfurization and organic matter preservation and structure. This detailed approach provides a better understanding on source rock development during the Cenomanian to Turonian in a global context, as many of the geochemical features were identified worldwide for deposits related to OAE2. (Author)

Estimating thermal maturity in the Eagle Ford Shale petroleum system using gas gravity data

Science.gov (United States)

Birdwell, Justin E.; Kinney, Scott A.

2017-01-01

Basin-wide datasets that provide information on the geochemical properties of petroleum systems, such as source rock quality, product composition, and thermal maturity, are often difficult to come by or assemble from publically available data. When published studies are available and include these kinds of properties, they generally have few sampling locations and limited numbers and types of analyses. Therefore, production-related data and engineering parameters can provide useful proxies for geochemical properties that are often widely available across a play and in some states are reported in publically available or commercial databases. Gas-oil ratios (GOR) can be calculated from instantaneous or cumulative production data and can be related to the source rock geochemical properties like kerogen type (Lewan and Henry, 1999) and thermal maturity (Tian et al., 2013; U.S. Energy Information Administration [EIA], 2014). Oil density or specific gravity (SG), often reported in American Petroleum Institute units (°API = 141.5 /SG – 131.5), can also provide information on source rock thermal maturity, particularly when combined with GOR values in unconventional petroleum systems (Nesheim, 2017).

Total petroleum systems of the Paleozoic and Jurassic, Greater Ghawar Uplift and adjoining provinces of central Saudi Arabia and northern Arabian-Persian Gulf

Science.gov (United States)

Pollastro, Richard M.

2003-01-01

The greater Paleozoic and Jurassic petroleum systems of the Arabian Peninsula form two of the most prolific petroleum-producing systems in the world. Source rocks of these systems extend throughout the eastern Arabian Peninsula and Arabian-Persian Gulf. Primary elements of these Paleozoic and Jurassic petroleum systems - source, reservoir, and seal rocks - are of great areal extent and exceptional quality. The combination of these regionally extensive, exceptional petroleum-system elements, and the formation of large subtle structural closures prior to, or coincident with, peak oil generation and migration, have produced oil and gas fields with reserve volumes second to none.

Application of uniaxial confining-core clamp with hydrous pyrolysis in petrophysical and geochemical studies of source rocks at various thermal maturities

Science.gov (United States)

Lewan, Michael D.; Birdwell, Justin E.; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

2013-01-01

Understanding changes in petrophysical and geochemical parameters during source rock thermal maturation is a critical component in evaluating source-rock petroleum accumulations. Natural core data are preferred, but obtaining cores that represent the same facies of a source rock at different thermal maturities is seldom possible. An alternative approach is to induce thermal maturity changes by laboratory pyrolysis on aliquots of a source-rock sample of a given facies of interest. Hydrous pyrolysis is an effective way to induce thermal maturity on source-rock cores and provide expelled oils that are similar in composition to natural crude oils. However, net-volume increases during bitumen and oil generation result in expanded cores due to opening of bedding-plane partings. Although meaningful geochemical measurements on expanded, recovered cores are possible, the utility of the core for measuring petrophysical properties relevant to natural subsurface cores is not suitable. This problem created during hydrous pyrolysis is alleviated by using a stainless steel uniaxial confinement clamp on rock cores cut perpendicular to bedding fabric. The clamp prevents expansion just as overburden does during natural petroleum formation in the subsurface. As a result, intact cores can be recovered at various thermal maturities for the measurement of petrophysical properties as well as for geochemical analyses. This approach has been applied to 1.7-inch diameter cores taken perpendicular to the bedding fabric of a 2.3- to 2.4-inch thick slab of Mahogany oil shale from the Eocene Green River Formation. Cores were subjected to hydrous pyrolysis at 360 °C for 72 h, which represents near maximum oil generation. One core was heated unconfined and the other was heated in the uniaxial confinement clamp. The unconfined core developed open tensile fractures parallel to the bedding fabric that result in a 38 % vertical expansion of the core. These open fractures did not occur in the

The Red Sea Basin Province: Sudr-Nubia(!) and Maqna(!) Petroleum Systems

Science.gov (United States)

Lindquist, Sandra J.

1999-01-01

The Sudr-Nubia(!) oil-prone total petroleum system dominates the densely explored Gulf of Suez part of the rifted Red Sea Basin Province. Upper Cretaceous to Eocene source rocks, primarily the Senonian Sudr Formation, are organic-rich, areally uniform marine carbonates that have generated known ultimate recoverable reserves exceeding 11 BBOE. The name Nubia is used for sandstone reservoirs with a wide range of poorly constrained, pre-rift geologic ages ranging from Early Paleozoic to Early Cretaceous. Syn- and post-rift Tertiary reservoirs, especially the Kareem Formation, also contain significant reserves. Partly overlapping Sudr-Nubia(!) is the areally larger and geochemically distinct, oil-and-gas-prone Maqna(!) total petroleum system within the southern Gulf of Suez basin and the sparsely explored remaining Red Sea basin. Known ultimate recoverable reserves are 50-100 MMBOE and more than 900 MMBOE, respectively, in those areas. Both the source and reservoir rocks in this petroleum system are Tertiary, dominantly Miocene, in age. Maqna(!) has the greater potential for future resource development.

Circum-Arctic petroleum systems identified using decision-tree chemometrics

Science.gov (United States)

Peters, K.E.; Ramos, L.S.; Zumberge, J.E.; Valin, Z.C.; Scotese, C.R.; Gautier, D.L.

2007-01-01

Source- and age-related biomarker and isotopic data were measured for more than 1000 crude oil samples from wells and seeps collected above approximately 55??N latitude. A unique, multitiered chemometric (multivariate statistical) decision tree was created that allowed automated classification of 31 genetically distinct circumArctic oil families based on a training set of 622 oil samples. The method, which we call decision-tree chemometrics, uses principal components analysis and multiple tiers of K-nearest neighbor and SIMCA (soft independent modeling of class analogy) models to classify and assign confidence limits for newly acquired oil samples and source rock extracts. Geochemical data for each oil sample were also used to infer the age, lithology, organic matter input, depositional environment, and identity of its source rock. These results demonstrate the value of large petroleum databases where all samples were analyzed using the same procedures and instrumentation. Copyright ?? 2007. The American Association of Petroleum Geologists. All rights reserved.

Shahejie-Shahejie/Guantao/Wumishan and Carboniferous/Permian Coal-Paleozoic Total Petroleum Systems in the Bohaiwan Basin, China (based on geologic studies for the 2000 World Energy Assessment Project of the U.S. Geological Survey)

Science.gov (United States)

Ryder, Robert T.; Qiang, Jin; McCabe, Peter J.; Nuccio, Vito F.; Persits, Felix

2012-01-01

This report discusses the geologic framework and petroleum geology used to assess undiscovered petroleum resources in the Bohaiwan basin province for the 2000 World Energy Assessment Project of the U.S. Geological Survey. The Bohaiwan basin in northeastern China is the largest petroleum-producing region in China. Two total petroleum systems have been identified in the basin. The first, the Shahejie&ndashShahejie/Guantao/Wumishan Total Petroleum System, involves oil and gas generated from mature pods of lacustrine source rock that are associated with six major rift-controlled subbasins. Two assessment units are defined in this total petroleum system: (1) a Tertiary lacustrine assessment unit consisting of sandstone reservoirs interbedded with lacustrine shale source rocks, and (2) a pre-Tertiary buried hills assessment unit consisting of carbonate reservoirs that are overlain unconformably by Tertiary lacustrine shale source rocks. The second total petroleum system identified in the Bohaiwan basin is the Carboniferous/Permian Coal–Paleozoic Total Petroleum System, a hypothetical total petroleum system involving natural gas generated from multiple pods of thermally mature coal beds. Low-permeability Permian sandstones and possibly Carboniferous coal beds are the reservoir rocks. Most of the natural gas is inferred to be trapped in continuous accumulations near the center of the subbasins. This total petroleum system is largely unexplored and has good potential for undiscovered gas accumulations. One assessment unit, coal-sourced gas, is defined in this total petroleum system.

Neoproterozoic rift basins and their control on the development of hydrocarbon source rocks in the Tarim Basin, NW China

Science.gov (United States)

Zhu, Guang-You; Ren, Rong; Chen, Fei-Ran; Li, Ting-Ting; Chen, Yong-Quan

2017-12-01

The Proterozoic is demonstrated to be an important period for global petroleum systems. Few exploration breakthroughs, however, have been obtained on the system in the Tarim Basin, NW China. Outcrop, drilling, and seismic data are integrated in this paper to focus on the Neoproterozoic rift basins and related hydrocarbon source rocks in the Tarim Basin. The basin consists of Cryogenian to Ediacaran rifts showing a distribution of N-S differentiation. Compared to the Cryogenian basins, those of the Ediacaran are characterized by deposits in small thickness and wide distribution. Thus, the rifts have a typical dual structure, namely the Cryogenian rifting and Ediacaran depression phases that reveal distinct structural and sedimentary characteristics. The Cryogenian rifting basins are dominated by a series of grabens or half grabens, which have a wedge-shaped rapid filling structure. The basins evolved into Ediacaran depression when the rifting and magmatic activities diminished, and extensive overlapping sedimentation occurred. The distributions of the source rocks are controlled by the Neoproterozoic rifts as follows. The present outcrops lie mostly at the margins of the Cryogenian rifting basins where the rapid deposition dominates and the argillaceous rocks have low total organic carbon (TOC) contents; however, the source rocks with high TOC contents should develop in the center of the basins. The Ediacaran source rocks formed in deep water environment of the stable depressions evolving from the previous rifting basins, and are thus more widespread in the Tarim Basin. The confirmation of the Cryogenian to Ediacaran source rocks would open up a new field for the deep hydrocarbon exploration in the Tarim Basin.

Petroleum Systems and Assessment of Undiscovered Oil and Gas in the Raton Basin - Sierra Grande Uplift Province, Colorado and New Mexico - USGS Province 41

Science.gov (United States)

Higley, Debra K.

2007-01-01

Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas resources of the Raton Basin-Sierra Grande Uplift Province of southeastern Colorado and northeastern New Mexico (USGS Province 41). The Cretaceous Vermejo Formation and Cretaceous-Tertiary Raton Formation have production and undiscovered resources of coalbed methane. Other formations in the province exhibit potential for gas resources and limited production. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define two total petroleum systems and five assessment units. All five assessment units were quantitatively assessed for undiscovered gas resources. Oil resources were not assessed because of the limited potential due to levels of thermal maturity of petroleum source rocks.

Geochemical investigation of petroleum source rocks by using Rock- Eval data in the Agha-Jari oilfield

Directory of Open Access Journals (Sweden)

Behzad khani

2015-01-01

Full Text Available In this study, 40 drilling cutting of the Pabdeh, Gurpi, kazhdumi and Gadvan Formations from the Agha-Jari Oilfield were analyzed by using Rock-Eval pyrolysis. In order to recognizing sedimentary environmental conditions of studied Formations, they are divided to 4 zones which A (Kazhdumi Formation#187 and C (Kazhdumi Formation#140 zones show reduction conditions by presence of sea organic materials and B (Gadvan Formation #140 and D(Gadvan Formation#187 zones show oxidation conditions by presence of continental organic materials to basin. Based on the Rock-Eval pyrolysis data, the Pabeh, Gurpi, Kazhdumi and Gadvan Formations have variable hydrocarbon generative potential. HI vs. OI plot revealed that the kerogen type in this Formations is a mixed of types II & III. The intensity of matrix effect in the Pabdeh, Gurpi, Kazhdumi and Gadvan Formations was compared by using S2 vs. TOC plot and calculating its regression equation. The results show that the significant amount of S2 adsorption by matrix was happened in the Pabdeh (4.98-6.96 mg HC/gr rock in wells 113 and 121 and Gurpi Formations ‌(4.33 mg HC/gr rock in well 113 which is due to their low thermal maturity‌(Tmax

Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

,

2013-01-01

In 2002, the U.S. Geological Survey (USGS) estimated undiscovered oil and gas resources that have the potential for additions to reserves in the San Juan Basin Province, New Mexico and Colorado. Paleozoic rocks were not appraised. The last oil and gas assessment for the province was in 1995. There are several important differences between the 1995 and 2002 assessments. The area assessed is smaller than that in the 1995 assessment. This assessment of undiscovered hydrocarbon resources in the San Juan Basin Province also used a slightly different approach in the assessment, and hence a number of the plays defined in the 1995 assessment are addressed differently in this report. After 1995, the USGS has applied a total petroleum system (TPS) concept to oil and gas basin assessments. The TPS approach incorporates knowledge of the source rocks, reservoir rocks, migration pathways, and time of generation and expulsion of hydrocarbons; thus the assessments are geologically based. Each TPS is subdivided into one or more assessment units, usually defined by a unique set of reservoir rocks, but which have in common the same source rock. Four TPSs and 14 assessment units were geologically evaluated, and for 13 units, the undiscovered oil and gas resources were quantitatively assessed.

Petroleum geology of the Palo Duro Basin, Texas Panhandle

International Nuclear Information System (INIS)

Rose, P.R.

1986-03-01

The Palo Duro Basin, Permian Basin, Texas is an asymmetric, relatively shallow, intracratonic basin in the southern Texas Panhandle filled mostly by Mississippian, Pennsylvanian, and Permian sedimentary rocks. Although deeper and prolific prolific petroleum-producing basins adjoin it on the north (Anadarko Basin), south (Midland Basin), and east (Hardeman Basin), the Palo Duro Basin has produced remarkably small amounts of oil and gas to date. This is all the more noteworthy because the sedimentary sequence and rock types of the basin are similar to those of the adjacent basins. Analyses of the stratigraphic succession and structural configuration of the Palo Duro Basin suggest that adequate reservoir rocks, top-seals, and geologic structures are present. Most of the structures formed early enough to have trapped hydrocarbons if they were migrating in the rock column. Although additional work is under way to properly address the question of the petroleum source rocks, generation, and migration, the general absence of production in the basin may relate to an overall deficiency in hydrocarbon generation within the basin. Geologic information in this report will form part of the basis for further analysis and conclusions on hydrocarbon potential in the Palo Duro Basin

Total petroleum systems of the Trias/Ghadames Province, Algeria, Tunisia, and Libya; the Tanezzuft-Oued Mya, Tanezzuft-Melrhir, and Tanezzuft-Ghadames

Science.gov (United States)

Klett, T.R.

2000-01-01

Undiscovered conventional oil and gas resources were assessed within total petroleum systems of the Trias/Ghadames Province (2054) as part of the U.S. Geological Survey World Petroleum Assessment 2000. The Trias/Ghadames Province is in eastern Algeria, southern Tunisia, and westernmost Libya. The province and its total petroleum systems generally coincide with the Triassic Basin. The province includes the Oued Mya Basin, Melrhir Basin, and Ghadames (Berkine) Basin. Although several total petroleum systems may exist within each of these basins, only three “composite” total petroleum systems were identified. Each total petroleum system occurs in a separate basin, and each comprises a single assessment unit.The main source rocks are the Silurian Tanezzuft Formation (or lateral equivalents) and Middle to Upper Devonian mudstone. Maturation history and the major migration pathways from source to reservoir are unique to each basin. The total petroleum systems were named after the oldest major source rock and the basin in which it resides.The estimated means of the undiscovered conventional petroleum volumes in total petroleum systems of the Trias/Ghadames Province are as follows [MMBO, million barrels of oil; BCFG, billion cubic feet of gas; MMBNGL, million barrels of natural gas liquids]:Tanezzuft-Oued Mya 830 MMBO 2,341 BCFG 110 MMBNGLTanezzuft-Melrhir 1,875 MMBO 4,887 BCFG 269 MMBNGLTanezzuft-Ghadames 4,461 MMBO 12,035 BCFG 908 MMBNGL

Oil source rocks in the Adiyaman area, southeast Turkey

Science.gov (United States)

Soylu, Cengiz

In the Adiyaman area, southeast Turkey, two carbonate source rock units, the Karababa-A Member and the Karabogaz Formation, are identified. The maturity levels of the source rock units increase towards the north and the west. Both the Karababa-A Member and the Karabogaz Formation are good to excellent oil-source rocks with widespread "kitchen areas".

Qingshankou-Putaohua/Shaertu and Jurassic Coal-Denglouku/Nongan total petroleum systems in the Songliao Basin, China

Science.gov (United States)

Ryder, Robert T.; Qiang, Jin; McCabe, Peter J.; Nuccio, Vito F.; Persits, Felix

2003-01-01

The Qingshankou-Putaohua/Shaertu petroleum system involves the generation of oil and gas from a mature pod of lacustrine source rock near the center of the Songliao Basin in northeastern China. The primary source rock is the Lower Cretaceous Qingshankou Formation, and a secondary source rock is Member 1 of the Lower Cretaceous Nenjiang Formation. The most productive of six sandstone reservoirs are the Putaohua reservoir (Member 1 of the Lower Cretaceous Yaojia Formation) and the Shaertu reservoir (Members 2 and 3 of the Yaojia Formation and Member 1 of the Nenjiang Formation). Most oil and associated gas generated from the Qingshankou Formation and Nenjiang Formation (Member 1) are trapped in large faulted anticlines, fault blocks, and faulted anticlinal noses in combination with facies-change and (or) diagenetic stratigraphic traps. Two assessment units are defined in the petroleum system: (1) an anticlinal assessment unit; and (2) a subtle-traps assessment unit consisting of (a) anticlinal noses in combination with fault or stratigraphic traps, (b) stratigraphic traps, and (c) unconventional reservoirs. Undiscovered conventional oil and gas resources are expected in both assessment units in small (5?10 million barrels of oil; 30?60 billion ft3 gas) and medium (10?25 million barrels of oil; 60?150 billion ft3 of gas) fields. Also, undiscovered conventional oil and gas resources are expected in several large fields (25?73 million barrels of oil; 150?173 billion ft3 of gas). The Jurassic coal?Dengloukou/Nongan petroleum system involves the generation of natural gas from multiple pods of mature source rock in graben structures at the base of the Songliao Basin. Sandstone and conglomeratic sandstone in the Lower Cretaceous Denglouku Formation and the Lower Cretaceous Quantou Formation are the major reservoir rocks. Most of the known natural gas is trapped in anticlines, anticlinal noses, and fault blocks. This petroleum system is largely unexplored in comparison to

Proceedings of the 39. annual conference of the Ontario Petroleum Institute

International Nuclear Information System (INIS)

2000-01-01

Several issues relevant to the petroleum industry in Ontario were presented at this thirty-ninth annual conference of the Ontario Petroleum Institute. The presentations dealt with a variety of topics including the sedimentology and petrology of oil and natural gas reservoirs, with emphasis on their depositional histories and geological correlations such as sequence stratigraphy, source rocks, and hydrodynamics. Many of the papers reviewed exploration methods, market economics and enhanced recovery techniques. A total of 15 papers were presented at this conference, of which 8 were processed separately for inclusion in the database. refs., tabs., figs

Source rock hydrocarbons. Present status

International Nuclear Information System (INIS)

Vially, R.; Maisonnier, G.; Rouaud, T.

2013-01-01

This report first presents the characteristics of conventional oil and gas system, and the classification of liquid and gaseous non conventional hydrocarbons, with the peculiar case of coal-bed methane. The authors then describe how source rock hydrocarbons are produced: production of shale oils and gases (horizontal drilling, hydraulic fracturing, exploitation) and of coal-bed methane and coal mine methane. In the next part, they address and discuss the environmental impact of source rock hydrocarbon production: installation footprint, water resource management, drilling fluids, fracturing fluids composition, toxicity and recycling, air pollution, induced seismicity, pollutions from other exploitation and production activities. They propose an overview of the exploitation and production of source rock gas, coal-bed gas and other non conventional gases in the world. They describe the current development and discuss their economic impacts: world oil context and trends in the USA, in Canada and other countries, impacts on the North American market, on the world oil industry, on refining industries, on the world oil balance. They analyse the economic impacts of non conventional gases: development potential, stakes for the world gas trade, consequence for gas prices, development opportunities for oil companies and for the transport sector, impact on CO 2 emissions, macro-economic impact in the case of the USA

Characterization of contamination, source and degradation of petroleum between upland and paddy fields based on geochemical characteristics and phospholipid fatty acids.

Science.gov (United States)

Zhang, Juan; Wang, Renqing; Du, Xiaoming; Li, Fasheng; Dai, Jiulan

2012-01-01

To evaluate contamination caused by petroleum, surface soil samples were collected from both upland and paddy fields along the irrigation canals in the Hunpu wastewater irrigation region in northeast China. N-alkanes, terpanes, steranes, and phospholipid fatty acids (PLFA) in the surface soil samples were analyzed. The aliphatic hydrocarbon concentration was highest in the samples obtained from the upland field near an operational oil well; it was lowest at I-3P where wastewater irrigation promoted the downward movement of hydrocarbons. The Hunpu region was found contaminated by heavy petroleum from oxic lacustrine fresh water or marine deltaic source rocks. Geochemical parameters also indicated significantly heavier contamination and degradation in the upland fields compared with the paddy fields. Principal component analysis based on PLFA showed various microbial communities between petroleum contaminated upland and paddy fields. Gram-negative bacteria indicated by 15:0, 3OH 12:0, and 16:1(9) were significantly higher in the paddy fields, whereas Gram-positive bacteria indicated by i16:0 and 18:1(9)c were significantly higher in the upland fields (p petroleum contamination. Poly-unsaturated PLFA (18:2omega6, 9; indicative of hydrocarbon-degrading bacteria and fungi) was also significantly elevated in the upland fields. This paper recommends more sensitive indicators of contamination and degradation of petroleum in soil. The results also provide guidelines on soil pollution control and remediation in the Hunpu region and other similar regions.

Crude petroleum

International Nuclear Information System (INIS)

1990-01-01

Crude petroleum statistics by country of production, export values and import values from 1983 to 1988 are given. Table A.1 of the Annex includes free market prices and price indices for crude petroleum based on average of Dubai, United Kingdom Brent and Alaska N Slope crude prices (price expressed in dollars/barrel). The data sources are: Crude petroleum United Nations Statistical Office; OPEC Annual Statistical Bulletin, and Petroleum Economist. For trade the sources of data are: National trade statistics; United Nations international trade statistics; International Moneytary Fund (IMF); Organization of the Petroleum Exporting Countries (OPEC); UNCTAD secretariat estimates. Tabs

Examination of the Reelfoot Rift Petroleum System, south-central United States, and the elements that remain for potential exploration and development

Science.gov (United States)

Coleman, James; Pratt, Thomas L.

2016-01-01

The Reelfoot rift is one segment of a late Proterozoic(?) to early Paleozoic intracontinental rift complex in the south-central United States. The rift complex is situated beneath Mesozoic to Cenozoic strata of the Mississippi embayment of southeastern Missouri, northeastern Arkansas, and western Tennessee and Kentucky. The rift portion of the stratigraphic section consists primarily of synrift Cambrian and Ordovician strata, capped by a postrift sag succession of Late Ordovician to Cenozoic age. Potential synrift source rocks have been identified in the Cambrian Elvins Shale. Thermal maturity of Paleozoic strata within the rift ranges from the oil window to the dry gas window. Petroleum generation in Elvins source rocks likely occurred during the middle to late Paleozoic. Upper Cretaceous sedimentary rocks unconformably overlie various Paleozoic units and define the likely upper boundary of the petroleum system.

Tectonics of East Siberian Sea Basin and its influence on petroleum systems

Science.gov (United States)

Karpov, Yury; Antonina, Stoupakova; Anna, Suslova; Mariia, Agasheva

2016-04-01

The East Siberian Sea basin (ESSB) is the largest part of the Siberian Arctic shelf, extending for over 1000 km from New Siberian Islands archipelago to Wrangel Island. Nowadays East Siberian Sea margin is considered as a region with probable high petroleum potential. This part of Russian Arctic shelf is the least studied. The major problems in geological investigation of East Siberian Sea shelf are absence of deep wells in area and low seismic exploration maturity. Only general conclusions on its geology and hydrocarbon systems can be drawn based on limited seismic, gravity and magnetic data, supported by projection of onshore geological data to offshore. So, that's why now only complex geological and seismic stratigraphy interpretations are provided. Today we have several concepts and can summarize the tectonic history of the basin. The basin is filled with siliclastic sediments. In the deepest depocentres sediments thickness exceed 8 km in average. Seismic data was interpreted using methods of seismic stratigraphy. Stratigraphic interpretation was possible to achieve because seismic reflections follow chronostratigraphic correlations. Finally, main seismic horizons were indicated. Each indicated horizon follows regional stratigraphic unconformity. In case of absence of deep wells in ESSB, we can only prove possible source rocks by projection of data about New Siberian Islands archipelago source rocks on offshore. The petroleum potential of these rocks was investigated by several authors [1, 2, 3]. Perspective structures, investigated in ESSB were founded out by comparing seismogeological cross-sections with explored analogs in other Russian and foreign onshore and offshore basins. The majority of structures could be connected with stratigraphic and fault traps. New data on possible petroleum plays was analyzed, large massif of data on geology and tectonic history of the region was collected, so now we can use method of basin modelling to evaluate hydrocarbon

Magmatism and petroleum exploration in the Brazilian Paleozoic basins

Energy Technology Data Exchange (ETDEWEB)

Thomaz Filho, Antonio; Antonioli, Luzia [Universidade do Estado do Rio de Janeiro, Faculdade de Geologia, Rua Sao Francisco Xavier, no 524/2030, CEP 20550-900, Rio de Janeiro, RJ (Brazil); Mizusaki, Ana Maria Pimentel [Universidade Federal do Rio Grande do Sul, Instituto de Geociencias, Avenida Bento Goncalves, no 9500, Campus do Vale, CEP 91509-900, Porto Alegre, RS (Brazil)

2008-02-15

Petroleum exploration in the Paleozoic sedimentary basins of Brazil has proven very challenging for explorationists. Except for the Solimoes Basin, in which transcurrent tectonism formed prospective structural highs, Brazilian Paleozoic basins lack intense structural deformation, and hence the detection and prospecting of place is often difficult. Magmatic intrusive and associated rocks in all these basins have traditionally been considered heat sources and hydrocarbon traps. The role of tholeiitic basic dikes in the generation, migration and accumulation of petroleum in the Anhembi oil occurrence (Sao Paulo State) is discussed herein. It follows that similar geological settings in other Paleozoic basins can be regarded as promising sites for oil accumulation that warrant investigation via modern geological and geophysical methods. (author)

Petroleum system modeling capabilities for use in oil and gas resource assessments

Science.gov (United States)

Higley, Debra K.; Lewan, Michael; Roberts, Laura N.R.; Henry, Mitchell E.

2006-01-01

Summary: Petroleum resource assessments are among the most highly visible and frequently cited scientific products of the U.S. Geological Survey. The assessments integrate diverse and extensive information on the geologic, geochemical, and petroleum production histories of provinces and regions of the United States and the World. Petroleum systems modeling incorporates these geoscience data in ways that strengthen the assessment process and results are presented visually and numerically. The purpose of this report is to outline the requirements, advantages, and limitations of one-dimensional (1-D), two-dimensional (2-D), and three-dimensional (3-D) petroleum systems modeling that can be applied to the assessment of oil and gas resources. Primary focus is on the application of the Integrated Exploration Systems (IES) PetroMod? software because of familiarity with that program as well as the emphasis by the USGS Energy Program on standardizing to one modeling application. The Western Canada Sedimentary Basin (WCSB) is used to demonstrate the use of the PetroMod? software. Petroleum systems modeling quantitatively extends the 'total petroleum systems' (TPS) concept (Magoon and Dow, 1994; Magoon and Schmoker, 2000) that is employed in USGS resource assessments. Modeling allows integration of state-of-the-art analysis techniques, and provides the means to test and refine understanding of oil and gas generation, migration, and accumulation. Results of modeling are presented visually, numerically, and statistically, which enhances interpretation of the processes that affect TPSs through time. Modeling also provides a framework for the input and processing of many kinds of data essential in resource assessment, including (1) petroleum system elements such as reservoir, seal, and source rock intervals; (2) timing of depositional, hiatus, and erosional events and their influences on petroleum systems; (3) incorporation of vertical and lateral distribution and lithologies of

Pre-Messinian (Sub-Salt Source-Rock Potential on Back-Stop Basins of the Hellenic Trench System (Messara Basin, Central Crete, Greece

Directory of Open Access Journals (Sweden)

Maravelis A.

2016-01-01

Full Text Available The Greek part of the Mediterranean Ridge suggests, in terms of its hydrocarbon potential, further frontier exploration. The geological similarities between its prolific portions, within the Cyprus and Egyptian Exclusive Economic Zones, indicate possible recoverable natural gas reserves in its Greek portion. Nevertheless it lacks of systematic frontier exploration although direct petroleum indicators occur. Active mud volcanoes on the Mediterranean Ridge, still emitting concurrently gas and gas hydrates, have not been yet assessed even though are strongly related to hydrocarbon occurrence worldwide (Caspian Sea, Gulf of Mexico, Western African Basin, Trinidad-Tobago, the Nile Cone. For this reason, the source rock potential of the Late Miocene lacustrine deposits on a backstop basin of the Hellenic Trench System (Messara Basin, Crete, Greece, was studied. The obtained pyrolysis data indicate that the containing organic matter is present in sufficient abundance and with good enough quality to be regarded as potential source rocks. The observed type III kerogen suggests gas generation potential. Although indications of higher thermal evolution occur the studied rocks suggest low maturation levels. The biogenic gas seeps in the studied research well further demonstrate the regional gas generation potential.

Characterization of a petroleum system in the Himalayan foreland basin

Energy Technology Data Exchange (ETDEWEB)

Sorkhabi, R. [Japan National Oil Corp., Tokyo (Japan)

1998-10-30

The Himalayan foreland basin that is a part of the Tethyan tectonic belt is a potential target for hydrocarbon exploration. Petroleum has been yield in the west part of basin (Pakistan), and in the east part (Myanmar). This study takes aim to the central parts of the Himalayan foreland basin (India and Nepal), and identifies sediments Paleocene in age (the Subathu Formation made up of limestone and shale, and Murree Group made up of mudstone and shale) as source rock (TOC content up to 0.5 %), and also identifies permeable Siwalik sandstone (Paleocene-Middle to Neogene) as reservoir rock (porosity ranges from 4 to 27%, and permeability ranges from 0.1 to 10 millidarcy). Source rock had been occurred thermal maturity by burial in late Miocene. The serious problem is the localization of seals and traps. It indicates a potentiality that suitable trap structures had been formed by Main Boundary Thrust (MBT), close to Lesser Himalaya, lifting up and transporting the Proterozoic shale and carbonate rocks atop the Siwalik sandstone. The overthrust activities of source rock (Subathu-Murree Group) atop the Siwalik are important for formation of seals and traps. Actuary, gas and oil seeps are found not in Tarai (plain) but in the vicinity of the MBT. (translated by NEDO)

Phosphate-rich sedimentary rocks: significance for organic facies and petroleum exploration

Energy Technology Data Exchange (ETDEWEB)

Waples, D W

1982-03-01

Phosphorus-bearing rocks and sediments can be divided into two genetically distinct classes: phosphatic shales or limestones and phosphorites. Phosphatic shales are primary sediments in which phosphate nodules or micronodules have formed diagenetically by precipitation of calcium phosphates derived mainly from organic phosphorus. The nodules form in reducing environments at shallow depths within the sediments, where loss of phosphate by diffusion to the overlying water column is minimized. Highly biogenic sediments containing large amounts of organic matter and some fine clastic debris provide ideal environments for the formation of phosphate nodules. Phosphorites, in contrast, represent concentrated accumulations of reworked phosphate nodules which originated in phosphatic shales or limestones. Currents, wave action, recrystallization, and erosion and resedimentation are important mechanisms in the concentration process. Phosphatic shales and limestones may become excellent oil source rocks if thermal maturity is achieved. They are useful facies indicators for anoxic or nearly anoxic depositional environments, and are often associated with restricted basins, or, during certain geologic periods, with broad shelves developed during transgressions. Phosphorites, in contrast, are often correlated with sea-level regressions or uplifts. They are modest source rocks because of their low organic carbon contents and the fact that they were reworked under oxidizing conditions. Nevertheless, because phosphorites are derived from, and often grade into, phosphatic shales, they also are of potential utility in the search for oil source beds.

The strata and palaeo-geomorphology framework at the end of neoproterozoic and development mode of source rocks at the beginning of Cambrian in Tarim Basin, China

Directory of Open Access Journals (Sweden)

Xin Yang

2017-12-01

Full Text Available Referred to the new recognition from petroleum exploration of the Sinian to Cambrian in South China, it could be considered that the distribution of the early Cambrian source rocks was controlled by the palaeo-geomorphology at the end of Neoproterozoic in the Tarim Basin. Based on the zircon U-Pb dating of pyroclastic rock samples from the clastic rock stratum under the bottom of Cambrian carbonate rocks, the stratigraphic correlation of the Sinian to Cambrian was conducted to build the palaeo-geomorphology framework at the end of Neoproterozoic in Tarim Basin. Lastly, according to the development mode of source rocks at the beginning of Cambrian, the distribution of source rocks was predicted initially through the division of seismic facies. The youngest zircon concordia age of pyroclastic rocks from the bottom of well Tong 1 is 707±8Ma. It was revealed by the strata framework of the Sinian to Cambrian, the palaeo-geomorphology at the end of Neoproterozoic in Tarim Basin was characterized by an uplift highland in Bachu-Tazhong area, the south north high-low, and the west is higher than the east. The distribution of source rocks in the bottom of the Cambrian on the palaeo-platform and slopes was coincident with the Upper Sinian dolomite basically. But the contemporaneous sediment happened to be absent or changed in sedimentary facies on the uplift and its edges. From the seismic facies of the strata under the bottom of Cambrian, it could be concluded that source rocks in the type of the Xishanbraque Group (∈1xs was limited in the Manjiaer Depression, while the source rocks in the type of the Yuertusi Group (∈1y are widely distributed in south of Tabei Uplift, east Awat Depression, and even the Maigt Slope. However, among the west Awat Depression and western Tanguzibasi Depression, and the middle area of the Bachu-Tazhong Uplifts, the contemporaneous source rocks may have changed into sedimentary facies of tidal flat and lagoon, instead of

The source rock characters of U-rich granite

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Feng; Debao, He [CNNC Key Laboratory of Uranium Resources Exploration and Evaluation Technology, Beijing Research Institute of Uranium Geology (China)

2012-03-15

This paper discusses the stratum composition, lithological association, uranium content of crust and the activation, migration, concentration of uranium at each tectonic cycle in South China. The authors point out that the source rock of U-rich granite is U-rich continental crust which is rich in Si, Al and K. The lithological association is mainly composed of terrestrial clastic rocks formation of mudstone and sandstone, mingled with intermediate-acidic, mafic pyroclastic rocks and carbonate rocks formation. During tectonic movements, the rocks had undergone regional metamorphism, migmatitization, granitization, and formed U-rich granites finally. (authors)

The source rock characters of U-rich granite

International Nuclear Information System (INIS)

Feng Mingyue; He Debao

2012-01-01

This paper discusses the stratum composition, lithological association, uranium content of crust and the activation, migration, concentration of uranium at each tectonic cycle in South China. The authors point out that the source rock of U-rich granite is U-rich continental crust which is rich in Si, Al and K. The lithological association is mainly composed of terrestrial clastic rocks formation of mudstone and sandstone, mingled with intermediate-acidic, mafic pyroclastic rocks and carbonate rocks formation. During tectonic movements, the rocks had undergone regional metamorphism, migmatitization, granitization, and formed U-rich granites finally. (authors)

Geothermal regime and Jurassic source rock maturity of the Junggar basin, northwest China

Science.gov (United States)

Nansheng, Qiu; Zhihuan, Zhang; Ershe, Xu

2008-01-01

We analyze the thermal gradient distribution of the Junggar basin based on oil-test and well-logging temperature data. The basin-wide average thermal gradient in the depth interval of 0-4000 m is 22.6 °C/km, which is lower than other sedimentary basins in China. We report 21 measured terrestrial heat flow values based on detailed thermal conductivity data and systematical steady-state temperature data. These values vary from 27.0 to 54.1 mW/m 2 with a mean of 41.8 ± 7.8 mW/m 2. The Junggar basin appears to be a cool basin in terms of its thermal regime. The heat flow distribution within the basin shows the following characteristics. (1) The heat flow decreases from the Luliang Uplift to the Southern Depression; (2) relatively high heat flow values over 50 mW/m 2 are confined to the northern part of the Eastern Uplift and the adjacent parts of the Eastern Luliang Uplift and Central Depression; (3) The lowest heat flow of smaller than 35 mW/m 2 occurs in the southern parts of the basin. This low thermal regime of the Junggar basin is consistent with the geodynamic setting, the extrusion of plates around the basin, the considerably thick crust, the dense lithospheric mantle, the relatively stable continental basement of the basin, low heat generation and underground water flow of the basin. The heat flow of this basin is of great significance to oil exploration and hydrocarbon resource assessment, because it bears directly on issues of petroleum source-rock maturation. Almost all oil fields are limited to the areas of higher heat flows. The relatively low heat flow values in the Junggar basin will deepen the maturity threshold, making the deep-seated widespread Permian and Jurassic source rocks in the Junggar basin favorable for oil and gas generation. In addition, the maturity evolution of the Lower Jurassic Badaowan Group (J 1b) and Middle Jurassic Xishanyao Group (J 2x) were calculated based on the thermal data and burial depth. The maturity of the Jurassic

Executive summary--2002 assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado: Chapter 1 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

,

2013-01-01

In 2002, the U.S. Geological Survey (USGS) estimated undiscovered oil and gas resources that have the potential for additions to reserves in the San Juan Basin Province (5022), New Mexico and Colorado (fig. 1). Paleozoic rocks were not appraised. The last oil and gas assessment for the province was in 1995 (Gautier and others, 1996). There are several important differences between the 1995 and 2002 assessments. The area assessed is smaller than that in the 1995 assessment. This assessment of undiscovered hydrocarbon resources in the San Juan Basin Province also used a slightly different approach in the assessment, and hence a number of the plays defined in the 1995 assessment are addressed differently in this report. After 1995, the USGS has applied a total petroleum system (TPS) concept to oil and gas basin assessments. The TPS approach incorporates knowledge of the source rocks, reservoir rocks, migration pathways, and time of generation and expulsion of hydrocarbons; thus the assessments are geologically based. Each TPS is subdivided into one or more assessment units, usually defined by a unique set of reservoir rocks, but which have in common the same source rock. Four TPSs and 14 assessment units were geologically evaluated, and for 13 units, the undiscovered oil and gas resources were quantitatively assessed.

Pulsed neutron logging - a modern approach to petroleum exploration

International Nuclear Information System (INIS)

Navalkar, M.P.

1978-01-01

As hydrocarbons have strikingly different properties for neutrons as compared with rocks, neutronic methods are useful to prepare logs of bore holes drilled for petroleum exploration. The earlier neutron logs were based on steady neutron sources, but the superior logs, namely, neutron life time log and neutron induced spectral log are based on pulsed neutron sources. The methods of obtaining these logs, their limitations and the field equipment required are described briefly. As the two logs are complementary, a plea has been made to develop field equipment which can obtain two logs in a single run. (M.G.B.)

Rock-Eval 6 Applications in Hydrocarbon Exploration, Production, and Soil Contamination Studies Les applications de Rock-Eval 6 dans l'exploration et la production des hydrocarbures, et dans les études de contamination des sols

Directory of Open Access Journals (Sweden)

Lafargue E.

2006-12-01

Full Text Available Successful petroleum exploration relies on detailed analysis of the petroleum system in a given area. Identification of potential source rocks, their maturity and kinetic parameters, and their regional distribution are best accomplished by rapid screening of rock samples (cores and/or cuttings using the Rock-Eval apparatus. The technique has been routinely used for about fifteen years and has become a standard tool for hydrocarbon exploration. This paper describes how the new functions of the latest version of Rock-Eval (Rock-Eval 6 have expanded applications of the method in petroleum geoscience. Examples of new applications are illustrated for source rock characterization, reservoir geochemistry, and environmental studies, including quantification. Le succès d'une exploration pétrolière repose sur l'analyse détaillée du système pétrolier dans une zone donnée. L'identification des roches mères potentielles, la détermination de leur maturité, de leurs paramètres cinétiques et de leur répartition sont réalisées au mieux à partir d'examens rapides d'échantillons de roches (carottes ou déblais au moyen de la pyrolyse Rock-Eval. Cette technique a été utilisée en routine pendant une quinzaine d'années et elle est devenue un outil standard pour l'exploration des hydrocarbures. Cet article décrit comment les nouvelles fonctionnalités de la dernière version de l'appareil Rock-Eval (Rock-Eval 6 ont permis une expansion des applications de la méthode en géosciences pétrolières. Des exemples d'applications nouvelles sont illustrés dans les domaines de la caractérisation des roches mères, de la géochimie de réservoir et des études environnementales incluant la quantification et la description des hydrocarbures dans des sols contaminés.

Geochemical characteristics of Lower Jurassic source rocks in the Zhongkouzi Basin

Science.gov (United States)

Niu, Haiqing; Han, Xiaofeng; Wei, Jianshe; Zhang, Huiyuan; Wang, Baowen

2018-01-01

Zhongkouzi basin is formed in Mesozoic and Cenozoic and developed on the Hercynian folded belt, the degree of exploration for oil and gas is relatively low hitherto. In order to find out the geochemical characteristics of the source rocks and the potentials for hydrocarbon generation. The research result shows that by analysis the geochemical characteristics of outcrop samples and new core samples in Longfengshan Group, Longfengshan Group are most developed intervals of favorable source rocks. They are formed in depression period of the basin when the sedimentary environments is salt water lacustrine and the water is keeping stable; The organic matter abundance is middle-higher, the main kerogen type is II1-II2 and few samples act as III type, The organic matter maturity is low maturity to medium maturity. The organic matter maturity of the source rock from eastern part of the basin is higher than in the western region. The source rock of Longfengshan Group are in the hydrocarbon generation threshold. The great mass of source rocks are matured and in the peak stage of oil generation.

Carbonate rock depositional models: A microfacies approach

Energy Technology Data Exchange (ETDEWEB)

Carozzi, A.V.

1988-01-01

Carbonate rocks contain more than 50% by weight carbonate minerals such as calcite, dolomite, and siderite. Understanding how these rocks form can lead to more efficient methods of petroleum exploration. Micofacies analysis techniques can be used as a method of predicting models of sedimentation for carbonate rocks. Micofacies in carbonate rocks can be seen clearly only in thin sections under a microscope. This section analysis of carbonate rocks is a tool that can be used to understand depositional environments, diagenetic evolution of carbonate rocks, and the formation of porosity and permeability in carbonate rocks. The use of micofacies analysis techniques is applied to understanding the origin and formation of carbonate ramps, carbonate platforms, and carbonate slopes and basins. This book will be of interest to students and professionals concerned with the disciplines of sedimentary petrology, sedimentology, petroleum geology, and palentology.

Kinetics of the generation of the petroleum: Principles and application in the Colombian basins

International Nuclear Information System (INIS)

Goncalves, F T T; Garcia, D F; Penteado, H L B; Giraldo, B N; Bedregal, R P; Gomez

2001-01-01

Most of the mathematical models that describe the conversion of kerogen into petroleum are based on the formulations of first-order kinetics. Although the application of such models requires the knowledge of the kinetic parameters (activation energies and frequency factor) of the kerogen, the usual practice in basin modeling studies is to use kinetic data of standard kerogen types (I, II or III) when measured data are not available. In this study, Rock-Eval pyrolysis under different heating rates and numerical optimization techniques were used to determine the kinetic parameters of cretaceous and tertiary source rocks of the upper Magdalena and llanos basins. The obtained kinetic parameters revealed a significant variability, which appears to be unrelated to the kerogen type classification based on hydrogen and oxygen indices. Modeling exercises under a constant heating rate (1.25 degrades C/M.y., 274.5K/M.y.) using the measured kinetic data indicates that kerogen conversion of organic facies with distinct kinetic parameters may be out of phase by 20-30M.y. therefore, petroleum generation and expulsion history might be longer and more complex than if the kinetic behavior of these rocks was considered homogeneous. These differences are critical in defining the timing between petroleum generations a trap formation/destruction, particularly in the case of the Colombian sedimentary basins, characterized by a highly complex tectonic evolution

Well-Posedness of a fully coupled thermo-chemo-poroelastic system with applications to petroleum rock mechanics

Directory of Open Access Journals (Sweden)

Tetyana Malysheva

2017-05-01

Full Text Available We consider a system of fully coupled parabolic and elliptic equations constituting the general model of chemical thermo-poroelasticity for a fluid-saturated porous media. The main result of this paper is the developed well-posedness theory for the corresponding initial-boundary problem arising from petroleum rock mechanics applications. Using the proposed pseudo-decoupling method, we establish, subject to some natural assumptions imposed on matrices of diffusion coefficients, the existence, uniqueness, and continuous dependence on initial and boundary data of a weak solution to the problem. Numerical experiments confirm the applicability of the obtained well-posedness results for thermo-chemo-poroelastic models with real-data parameters.

Petroleum system of Northwest Java basin based on gravity data analysis

Science.gov (United States)

Widianto, E.

2018-01-01

Energy management in the upstream oil and gas sector becomes very important for the country’s energy security. The renewal of energy resources and reserves becomes necessary and is a must. In the oil and gas industry, gravity data is usually used only for regional surveys, but with the development of instrumentation technology and gravity software development, this method can be used for assessing oil and gas survey stages from exploration to production. This study was conducted to evaluate aspects of petroleum system and exploration play concept in the part of Northwest Java Basin, covering source rock deposition regions (source kitchen area, migration direction), development of reservoirs, structural and stratigraphic trap, based on gravity data. This study uses data from Bouguer gravity anomaly map by filtering process to produce a residual map depicting sedimentation basin configuration. The mapping generated 20 sedimentary basins in Java Island with the total hydrocarbon resources of 113 BBOE (Billion Barrel of Oil Equivalent). The petroleum system analysis was conducted in the Northwest Basin section. The final map produced illustrates the condition of petroleum system and play concept that can be used as exploration direction, expectedly reducing the risk of drilling failure.

Relationships between stratigraphy, deformation and thermal history in sedimentary basins. Impact of geodynamic concepts in petroleum exploration

International Nuclear Information System (INIS)

Sarmiento, Luis Fernando

2002-01-01

The natural processes that generate petroleum accumulations in a sedimentary basin require several ingredients: (1) the petroleum system elements: source, reservoir, seal and overburden rocks, which are the result of sedimentation processes in a subsiding basin; (2) petroleum traps, which in many cases are the result of deformation and (3) heat to convert suitable organic matter into petroleum. Although these different phenomena are considered independent at the scale of an oil field, at the lithosphere scale thermal phenomena, (2) vertical movements of the earth surface responsible for sedimentation and erosion and (3) tectonic deformation are not independent phenomena, physical quantitative laws intimately relate them. These mutual inter relationships are useful in petroleum exploration to predict one factor having knowledge of the others. Applications of these concepts can contribute to understand the tectonic history of complex areas, such as the Colombian sedimentary basins and reduce exploration risk

Hot dry rock heat mining

International Nuclear Information System (INIS)

Duchane, D.V.

1992-01-01

Geothermal energy utilizing fluids from natural sources is currently exploited on a commercial scale at sites around the world. A much greater geothermal resource exists, however, in the form of hot rock at depth which is essentially dry. This hot dry rock (HDR) resource is found almost everywhere, but the depth at which usefully high temperatures are reached varies from place to place. The technology to mine the thermal energy from HDR has been under development for a number of years. Using techniques adapted from the petroleum industry, water is pumped at high pressure down an injection well to a region of usefully hot rock. The pressure forces open natural joints to form a reservoir consisting of a small amount of water dispensed in a large volume of hot rock. This reservoir is tapped by second well located at some distance from the first, and the heated water is brought to the surface where its thermal energy is extracted. The same water is then recirculated to mine more heat. Economic studies have indicated that it may be possible to produce electricity at competitive prices today in regions where hot rock is found relatively close to the surface

Impacts of petroleum production on ground and surface waters: Results from the Osage-Skiatook Petroleum Environmental Research A site, Osage County Oklahoma

Science.gov (United States)

Kharaka, Y.K.; Thordsen, J.J.; Kakouros, E.; Herkelrath, W.N.

2005-01-01

As part of a multidisciplinary group of about 20 scientists, we are investigating the transport, fate, natural attenuation, and ecosystem impacts of inorganic salts and organic compounds present in releases of produced water and associated hydrocarbons at the Osage-Skiatook Petroleum Environmental Research (OSPER) sites, located in Osage County, Oklahoma. Geochemical data collected from nearby oil wells show that the produced water source is a Na-Ca-Cl brine (???150,000 mg/L total dissolved solids [TDS]), with relatively high concentrations of Mg, Sr, and NH4, but low SO4 and H2S. Results from the depleted OSPER A site show that the salts continue to be removed from the soil and surficial rocks, but degraded oil persists on the contaminated surface. Eventually, the bulk of inorganic salts and dissolved organics in the brine will reach the adjacent Skiatook Lake, a 4250-ha (10,501-ac) potable water reservoir. Repeated sampling of 44 wells show a plume of high-salinity water (2000-30,000 mg/L TDS) at intermediate depths that intersects Skiatook Lake and extends beyond the visibly impacted areas. No liquid petroleum was observed in this plume, but organic acid anions, benzene, toluene, ethylbenzene, and xylene (BTEX), and other volatile organic carbon (VOC) are present. The chemical composition of released brine is modified by sorption, mineral precipitation and dissolution, evapotranspiration, volatilization, and bacterially mediated oxidation-reduction reactions, in addition to mixing with percolating precipitation water, lake water, and pristine groundwater. Results show that only minor amounts of salt are removed by runoff, supporting the conclusion that significant amounts of salts from produced water and petroleum releases still remain in the soils and rocks of the impacted area after more than 65 yr of natural attenuation. Copyright ?? 2005. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

Igneous-sedimentary petroleum systems; Sistemas petroliferos igneo-sedimentares

Energy Technology Data Exchange (ETDEWEB)

Eiras, Jaime Fernandes [Para Univ., Belem, PA (Brazil)]. E-mail: eiras@ufpa.br; Wanderley Filho, Joaquim Ribeiro [PETROBRAS S.A., Manaus, AM (Brazil). Unidade de Negocios-BSOL]. E-mail: jwand@petrobras.com.br

2003-07-01

Igneous-sedimentary petroleum systems are mixed systems in which one or more essential elements or processes are related to magmatic events. Many examples worldwide are presented to show the importance of igneous rocks in the exploratory activities, as well as in the petroleum occurrence. Volcanic ash layers are of great importance in stratigraphic correlation and elucidation of structures, particularly when they occur in thick nonfossiliferous strata. They are also good indicators of turbidite deposition where turbidity currents are related to earthquakes generated by magmatic events. Unconventional reservoirs can be created by volcanic eruptions or intrusions, crystallization, reworking, and fracturing. Unaltered igneous rocks can seal vertically and laterally conventional reservoirs due to its excellent cap capacity. Abnormal thermal effect of igneous rocks can compensate the lack of overburden in shallow basins. Structural or combined traps can be formed due to intrusions, such as folded, faulted, and unconformity traps. Porosity can be either primary or secondary, or both. Primary porosity mainly consists of cavities produced by gas volatilization during eruption and cooling. Secondary porosity refers to those pores that result from hydrothermal alteration, recrystallization, and dissolution by groundwater, and tectonic stress. It includes intercrystalline pores formed by crystallization of various secondary minerals, dissolution pores, and tectonic fractures. New technologies of petroleum development and production are encouraging to search for oil and gas within igneous rocks, and new discoveries are expected. (author)

Executive Summary -- assessment of undiscovered oil and gas resources of the San Joaquin Basin Province of California, 2003: Chapter 1 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

Science.gov (United States)

Gautier, Donald L.; Scheirer, Allegra Hosford; Tennyson, Marilyn E.; Peters, Kenneth E.; Magoon, Leslie B.; Lillis, Paul G.; Charpentier, Ronald R.; Cook, Troy A.; French, Christopher D.; Klett, Timothy R.; Pollastro, Richard M.; Schenk, Christopher J.

2007-01-01

In 2003, the U.S. Geological Survey (USGS) completed an assessment of the oil and gas resource potential of the San Joaquin Basin Province of California (fig. 1.1). The assessment is based on the geologic elements of each Total Petroleum System defined in the province, including hydrocarbon source rocks (source-rock type and maturation and hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined five total petroleum systems and ten assessment units within these systems. Undiscovered oil and gas resources were quantitatively estimated for the ten assessment units (table 1.1). In addition, the potential was estimated for further growth of reserves in existing oil fields of the San Joaquin Basin.

Continuous distillation of oil-bearing rocks

Energy Technology Data Exchange (ETDEWEB)

1923-11-14

A continuous process of distilling petroleum-bearing, asphaltic, or bituminous rocks to free bitumen is characterized by vaporizing hydrocarbons solid, pasty, or liquid from petroleum-containing asphaltic or bituminous rocks to free bitumen without ever reaching the temperatures at which they can produce decomposition, the necessary heat being furnished by combustion of part of the hydrocarbons of the treated rocks. A furnace for carrying out the process of claim 1 is characterized by consisting of a cavity lined inside with reflector, of variable section and with a throat at the upper part for charging the material to be treated and means for blowing the lower part of the furnace with the air necessary for combustion and inert gas for regulating the combustion and removal of the hydrocarbons.

Petroleum systems and geologic assessment of undiscovered oil and gas, Cotton Valley group and Travis Peak-Hosston formations, East Texas basin and Louisiana-Mississippi salt basins provinces of the northern Gulf Coast region. Chapters 1-7.

Science.gov (United States)

,

2006-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Cotton Valley Group and Travis Peak and Hosston Formations in the East Texas Basin and Louisiana-Mississippi Salt Basins Provinces in the Gulf Coast Region (USGS Provinces 5048 and 5049). The Cotton Valley Group and Travis Peak and Hosston Formations are important because of their potential for natural gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and eight assessment units. Seven assessment units were quantitatively assessed for undiscovered oil and gas resources.

Relationship of oil seep in Kudat Peninsula with surrounding rocks based on geochemical analysis

Science.gov (United States)

Izzati Azman, Nurul; Nur Fathiyah Jamaludin, Siti

2017-10-01

This study aims to investigate the relation of oil seepage at Sikuati area with the structural and petroleum system of Kudat Peninsula. The abundance of highly carbonaceous rocks with presence of lamination in the Sikuati Member outcrop at Kudat Peninsula may give an idea on the presence of oil seepage in this area. A detailed geochemical analysis of source rock sample and oil seepage from Sikuati area was carried out for their characterization and correlation. Hydrocarbon propectivity of Sikuati Member source rock is poor to good with Total Organic Carbon (TOC) value of 0.11% to 1.48%. and also categorized as immature to early mature oil window with Vitrinite Reflectance (VRo) value of 0.43% to 0.50 %Ro. Based on biomarker distribution, from Gas Chromatography (GC) and Gas Chromatography-Mass Spectrometry (GC-MS) analysis, source rock sample shows Pr/Ph, CPI and WI of 2.22 to 2.68, 2.17 to 2.19 and 2.46 to 2.74 respectively indicates the source rock is immature and coming from terrestrial environment. The source rock might be rich in carbonaceous material organic matter resulting from planktonic/bacterial activity which occurs at fluvial to fluvio-deltaic environment. Overall, the source rock from outcrop level of Kudat Peninsula is moderately prolific in term of prospectivity and maturity. However, as go far deeper beneath the surface, we can expect more activity of mature source rock that generate and expulse hydrocarbon from the subsurface then migrating through deep-seated fault beneath the Sikuati area.

Late Jurassic – early Cretaceous inversion of rift structures, and linkage of petroleum system elements across post-rift unconformity, U.S. Chukchi Shelf, arctic Alaska

Science.gov (United States)

Houseknecht, David W.; Connors, Christopher D.

2015-01-01

Basin evolution of the U.S. Chukchi shelf involved multiple phases, including Late Devonian–Permian rifting, Permian–Early Jurassic sagging, Late Jurassic–Neocomian inversion, and Cretaceous–Cenozoic foreland-basin development. The focus of ongoing exploration is a petroleum system that includes sag-phase source rocks; inversion-phase reservoir rocks; structure spanning the rift, sag, and inversion phases; and hydrocarbon generation during the foreland-basin phase.

The new challenges of petroleum

International Nuclear Information System (INIS)

Gernelle, E.

2006-02-01

Petroleum in in the center of our civilization: abundant, easy to use and energy powerful, it is used almost everywhere: transports, lighting, space heating, plastics, fertilizers, cloth industry etc. The 'black-gold' is the object of all stakes, from richness to power. However, petroleum is also at the origin of many evils: pollution, corruption, violence. Today, petroleum is a source of worries: how long will it last? How long will we be able to stand its impacts on environment? This book shades light on all these questions and supplies some concrete elements about this energy source. Content: technological challenges of petroleum; producers: powers and risks; consumers' dependence; to learn more about petroleum. (J.S.)

The Putumayo-Oriente-Maranon Province of Colombia, Ecuador, and Peru; Mesozoic-Cenozoic and Paleozoic petroleum systems

Science.gov (United States)

Higley, D.K.

2001-01-01

This report is an evaluation of oil and gas resources for petroleum systems of the Putumayo-Oriente-Maranon province of Columbia, Ecuador, and Peru. This assessment is a product of the World Energy Project of the U.S. Geological Survey, under the direction of Thomas Ahlbrandt. Described in this explanation of the petroleum geology of the Putumayo-Oriente-Maranon province are thermal maturation of hydrocarbon source rocks, primary reservoir formations, areas and volumes of oil and (or) gas production, and the history of exploration. Complete oil and gas resource assessment results are planned for a later publication, although some data and results are contained in this report.

Geological evolution of clay sediments: the petroleum exploration vision

International Nuclear Information System (INIS)

Schneider, F.

2004-01-01

The radioactive waste isolation capacity assessment for a clay sediment host rock is link: (1) to the understanding of their present state properties and 3-D repartition (from basin evolution, including sedimentary and diagenetic process); and (2) to the prediction of their future evolution during the next million years. For petroleum exploration, basin modelling aims at reconstructing the accumulation of hydrocarbons at basin scale, and at geological timescale, taking into account the effects of kinematics displacements, sedimentation, erosion, compaction, temperatures history, overpressures and fluids flows (water and hydrocarbons). Furthermore, explorationists wish to address overpressure reconstruction in order to estimate the risks of drilling. Clay sediments are of interest for petroleum exploration because source rocks and seal are generally composed of them. Nevertheless, in spite of their occurrence in nature their evolution at geological timescale is not well understood. And, most of the knowledge has been achieved by those working in the realms of soils mechanics and civil engineering until the present geological investigations for long term radioactive waste repositories. Application of this knowledge to clay sediment is considered to be valid within the first hundreds of meters at the top of the sedimentary pile, according to a repository depth. This paper is dedicated to the sedimentary rocks behaviour at geological timescale. This behaviour is characterised by: (1) the deposition of the sediment; (2) the loading path at geological timescale; (3) the constitutive law which includes the consolidation process and the rupture criteria; and (4) the parameters evolution related to consolidation. (author)

The potentiality of hydrocarbon generation of the Jurassic source rocks in Salam-3x well,

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2016-03-01

Full Text Available The present work deals with the identification of the potential and generating capability of oil generation in the Jurassic source rocks in the Salam-3x well. This depending on the organo-geochemical analyses of cutting samples representative of Masajid, Khatatba and Ras Qattara formations, as well as, representative extract samples of the Khatatba and Ras Qattara formations. The geochemical analysis suggested the potential source intervals within the encountered rock units as follows: Masajid Formation bears mature source rocks and have poor to fair generating capability for generating gas (type III kerogen. Khatatba Formation bears mature source rock, and has poor to good generating capability for both oil and gas. Ras Qattara Formation constituting mature source rock has good to very good generating capability for both oil and gas. The burial history modeling shows that the Masajid Formation lies within oil and gas windows; Khatatba and Ras Qattara formations lie within the gas window. From the biomarker characteristics of source rocks it appears that the extract is genetically related as the majority of them were derived from marine organic matters sources (mainly algae deposited under reducing environment and take the direction of increasing maturity and far away from the direction of biodegradation. Therefore, Masajid Formation is considered as effective source rocks for generating hydrocarbons, while Khatatba and Ras Qattara formations are the main source rocks for hydrocarbon accumulations in the Salam-3x well.

Upper Devonian (Frasnian) non-calcified, algae, Alberta: Geological relevance to Leduc platforms and petroleum source rocks

Energy Technology Data Exchange (ETDEWEB)

Dix, G.R. (Univ. of British Columbia, Vancouver, BC (Canada))

1990-12-01

Several types of non-calcified fossil algae comparable to extant brown and green benithic macrophytes occur abundantly on two bedding planes in drill core from argillaceous slope carbonates of the Ireton Formation in northern Alberta. Fossiliferous strata abruptly overlie part of a stepped-back margin of the Sturgeon Lake carbonate platform (Leduc Formation), southeast of the Peace River Arch. Fossils are flattened organic fragments, some representing nearly complete specimens. Tentative comparisons are made with some Paleozoic algae; some of the Sturgeon Lake flora may be new species or genera. Preliminary examination of selected cores from the Ireton Formation and organic-rich Duvernay Formation in central Alberta indicates a widespread distribution of algal-derived organic matter within Upper Devonian basinal strata. The geological relevance of non-calcified algae to Devonian carbonate platforms and basins is postulated in three cases. Their presence in slope sediments may indicate that algal lawns flourished in muddy, upper slope environments. Fossils accumulated either in situ, or were ripped up and quickly buried within downshope resedimented deposits. All or some algal fragments may have been swept from the adjacent carbonate platform during storms. Prolific shallow water algal growth may have occurred simultaneously with oceanic crises when shallow water carbonate production either decreased or was shut down. The present position of fossil algae, therefore, would mark a bedding surface that is stratigraphically equivalent to an intraplatform disconformity. Regardless of the original environment, a sufficient accumulation of non-calcified algae in slope strata represents a viable petroleum source proximal to carbonate platforms. 46 refs., 9 figs.

Petroleum 2006. Statistical elements

International Nuclear Information System (INIS)

2007-06-01

This document gathers in 5 parts, the main existing statistical data about petroleum industry in France and in the rest of the world, together with an insight on other energy sources: 1 - petroleum in the French economy (petroleum and other energies, petroleum and transports, petroleum and energy in the industry, the residential and tertiary sectors, environment: 42 pages); 2 - the French petroleum industry (exploration, production, foreign trade, transports, refining, storage, petrochemistry: 66 pages); 3 - the French market of petroleum products (evolution of sales by product and detail by region for the past year: 38 pages); 4 - prices and taxes of petroleum products (world prices and rates for crude and refined products, evolution of fret rates, retail prices and French taxes: 28 pages); 5 - petroleum in the world (world energy production and consumption, detailed petroleum activity by main areas and for the main countries: 112 pages). (J.S.)

Reliability analysis of hydrologic containment of liquefied petroleum gas within unlined rock caverns.

Science.gov (United States)

Gao, X.; Yan, E. C.; Yeh, T. C. J.; Wang, Y.; Liang, Y.; Hao, Y.

2017-12-01

Notice that most of the underground liquefied petroleum gas (LPG) storage caverns are constructed in unlined rock caverns (URCs), where the variability of hydraulic properties (in particular, hydraulic conductivity) has significant impacts on hydrologic containment performance. However, it is practically impossible to characterize the spatial distribution of these properties in detail at the site of URCs. This dilemma forces us to cope with uncertainty in our evaluations of gas containment. As a consequence, the uncertainty-based analysis is deemed more appropriate than the traditional deterministic analysis. The objectives of this paper are 1) to introduce a numerical first order method to calculate the gas containment reliability within a heterogeneous, two-dimensional unlined rock caverns, and 2) to suggest a strategy for improving the gas containment reliability. In order to achieve these goals, we first introduced the stochastic continuum representation of saturated hydraulic conductivity (Ks) of fractured rock and analyzed the spatial variability of Ks at a field site. We then conducted deterministic simulations to demonstrate the importance of heterogeneity of Ks in the analysis of gas tightness performance of URCs. Considering the uncertainty of the heterogeneity in the real world situations, we subsequently developed a numerical first order method (NFOM) to determine the gas tightness reliability at crucial locations of URCs. Using the NFOM, the effect of spatial variability of Ks on gas tightness reliability was investigated. Results show that as variance or spatial structure anisotropy of Ks increases, most of the gas tightness reliability at crucial locations reduces. Meanwhile, we compare the results of NFOM with those of Monte Carlo simulation, and we find the accuracy of NFOM is mainly affected by the magnitude of the variance of Ks. At last, for improving gas containment reliability at crucial locations at this study site, we suggest that vertical

Geology, sequence stratigraphy, and oil and gas assessment of the Lewis Shale Total Petroleum System, San Juan Basin, New Mexico and Colorado: Chapter 5 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

Dubiel, R.F.

2013-01-01

The Lewis Shale Total Petroleum System (TPS) in the San Juan Basin Province contains a continuous gas accumulation in three distinct stratigraphic units deposited in genetically related depositional environments: offshore-marine shales, mudstones, siltstones, and sandstones of the Lewis Shale, and marginal-marine shoreface sandstones and siltstones of both the La Ventana Tongue and the Chacra Tongue of the Cliff House Sandstone. The Lewis Shale was not a completion target in the San Juan Basin (SJB) in early drilling from about the 1950s through 1990. During that time, only 16 wells were completed in the Lewis from natural fracture systems encountered while drilling for deeper reservoir objectives. In 1991, existing wells that penetrated the Lewis Shale were re-entered by petroleum industry operators in order to fracture-stimulate the Lewis and to add Lewis gas production onto preexisting, and presumably often declining, Mesaverde Group production stratigraphically lower in the section. By 1997, approximately 101 Lewis completions had been made, both as re-entries into existing wells and as add-ons to Mesaverde production in new wells. Based on recent industry drilling and completion practices leading to successful gas production from the Lewis and because new geologic models indicate that the Lewis Shale contains both source rocks and reservoir rocks, the Lewis Shale TPS was defined and evaluated as part of this U.S. Geological Survey oil and gas assessment of the San Juan Basin. Gas in the Lewis Shale Total Petroleum System is produced from shoreface sandstones and siltstones in the La Ventana and Chacra Tongues and from distal facies of these prograding clastic units that extend into marine rocks of the Lewis Shale in the central part of the San Juan Basin. Reservoirs are in shoreface sandstone parasequences of the La Ventana and Chacra and their correlative distal parasequences in the Lewis Shale where both natural and artificially enhanced fractures produce

Méthode rapide de caractérisation des roches mètres, de leur potentiel pétrolier et de leur degré d'évolution Rapid Method for Source Rocks Characrerysation and for Determination of Petroleum Potential and Degree of Evolution

Directory of Open Access Journals (Sweden)

Espitalié J.

2006-11-01

Full Text Available Les études fondamentales réalisées sur les kérogènes à l'aide de diverses méthodes physico-chimiques d'analyse ont permis de mettre au point une méthode et un appareillage adaptés à l'exploration pétrolière. On expose dans cet article la mise au point de cette méthode et on montre, à l'aide des paramètres qu'elle permet d'obtenir, ses applications dans le domaine de l'exploration pétrolière - reconnaissance des différents types de roche mère et de leur potentiel pétrolier; - caractérisation de leur degré d'évolution (zone à huile - zone à gaz. On montre aussi que cette méthode convient particulièrement bien à l'estimation du rendement en huile des roches bitumineuses et à l'étude de la qualité et du rang des charbons. Fundamental research on kerogens by different physico-chemical analysis methods have led to the development of a method and equipment suited for petroleum exploration. This article describes the development of this method and, by means of the parameters it determines, shows how it con be applied in the field of petroleum exploration - exploring different types of source rock and their petroleum potential ; - characterizing their degree of evolution (ail zone/gas zone. This method is also shown ta be particularly suited for estimating the oil yield of cil shales and investigating the quality and classification of cool.

Geology and total petroleum systems of the Paradox Basin, Utah, Colorado, New Mexico, and Arizona

Science.gov (United States)

Whidden, Katherine J.; Lillis, Paul G.; Anna, Lawrence O.; Pearson, Krystal M.; Dubiel, Russell F.

2014-01-01

The geological model for the development of the Total Petroleum Systems (TPSs) within the Paradox Basin formed the foundation of the recent U.S. Geological Survey assessment of undiscovered, technically recoverable resources in the basin. Five TPSs were defined, of which three have known production and two are hypothetical. These TPSs are based on geologic elements of the basin and the potential development of Precambrian, Devonian, Pennsylvanian, Permian-Mississippian, and Cretaceous source rock intervals.

2D compositional modeling of petroleum generation, expulsion and migration in the Southern compartment of the Reconcavo Basin, Brazil; Modelisation compositionnelle 2D de la genese, expulsion et migration du petrole dans le compartiment sud du Bassin de Reconcavo, Bresil

Energy Technology Data Exchange (ETDEWEB)

Barroz Penteado, H.L. de

1999-01-07

The Reconcavo Basin is part of a rift formed between the Late Jurassic and the Early Cretaceous in northeastern Brazil. The objective of this thesis was the compositional modeling of petroleum generation, expulsion and migration along a cross-section in the Southern Compartment of the basin with the Temispack basin simulation software. A geochemical study of the lacustrine shales of the Gomo Member (Candelas Fm.) has been performed to determine their petroleum potential, the evolution of maturation with depth and changes in petroleum composition. Hydrogen indices of immature kerogens (400-850 mg/g TOC) were shown to be higher than those of whole rocks, thus indicating a retention of Rock-Eval pyrolysis products in the mineral matrix of these type I source rocks. Saturates (30-50% of organic extracts in the immature zone) increase both in absolute and in relative (60-80%) terms in the oil window (2000-2600 m) because of a partial secondary cracking of NSOs and aromatics. After having tested several scenarios of geodynamic evolution between the Aptian and the Oligocene, a variable thickness of post-rift sediments (maximum of 1200 m) has been shown to be necessary to calibrate maturity parameters. Petroleum migration has been modeled to understand migration pathways as well as the role of faults as drains. Thus, two petroleum migration systems have been identified for the Dom Joao and Cexis accumulations. Petroleum compositional variations have been modeled by coupling the processes of retention and secondary cracking. A good calibration of compositions was obtained with secondary cracking parameters for NSOs and aromatics which are close to those of the main primary cracking reaction of a type I kerogen, coupled with a retention of 50% of NSOs within the source rocks. (author)

Petroleum and geopolitics

International Nuclear Information System (INIS)

Chaigneau, P.

2004-01-01

Todays, petroleum companies consider that despite the constant increase of petroleum consumption, petroleum will remain the main energy source for at least 40 years. However, after the Iraq conflict, new regional situations are changing. China, for instance, with its growing up demand, will change the physiognomy of the oil market. In parallel, from Indonesia to Africa, petroleum and religion interfere and explain the new conflict areas. As for the US strategy, which is not limited to the energy paradigm, it largely integrates energy in the main lines of its diplomacy, from the 'Wide Middle East' to the 'Sahel initiative', and in its position with respect to Venezuela

Petroleum data for the pre-mid-Devonian basal clastics play, southern Mackenzie Valley

Energy Technology Data Exchange (ETDEWEB)

Lemieux, Y. [Natural Resources Canada, Yellowknife, NT (Canada). Geological Survey of Canada; Gal, L.P. [Northwest Territories Geoscience Office, Yellowknife, NT (Canada)

2008-07-01

This document presented petroleum data from the Mackenzie Corridor exploration area in the Northwest Territories. Both quantitative and qualitative geoscience data was compiled as part of a project under the Secure Canadian Energy Supply program of the Geological Survey of Canada. Three separate reservoir facies have been identified within the study area for their attributes relevant to petroleum exploration. This document defined and described the pre-mid-Devonian basal clastics play in the southern Great Slave Plains region where potential Lower Paleozoic source rocks include organic-rich beds of the Mirage Point and Chinchaga Formations, and regionally widespread, Middle to lower Upper Devonian shale. The play is analogous to the oil producing Middle Devonian clastic plays onlapping the Peace River Arch in northwestern Alberta. The seals, migration and trap styles for the reservoirs were discussed. Exploration risks include a thin and discontinuous reservoir with poor porosity; isolation from potential source beds; inadequate reservoir seals; and timing of hydrocarbon migration with respect to trap development. The petroleum play information was based on very few well penetrations. As such, the pre-mid-Devonian basal clastics play is considered to be a conceptual play that has not yet been adequately explored. 40 refs., 3 tabs., 12 figs.

CG/MS quantitation of diamondoid compounds in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.D.; Hollebone, B.P.; Fingas, M.; Peng, X.; Landriault, M.

2006-01-01

Diamondoids are a class of saturated hydrocarbons that consist of 3-dimensionally fused cyclohexane rings. Diamondoid compounds in petroleum are the result of carbonium ion rearrangements of cyclic precursors on clay superacids in the source rock during oil generation. They are considered to be a problem due to their deposition during production of reservoir fluids and transportation of natural gas, gas condensates and light crude oils. At high concentrations, and with changes in pressure and temperature, diamondoid compounds can segregate out of reservoir fluids during production. Environmental scientists have considered fingerprinting the diamondoid hydrocarbons as a forensic method for oil spill studies. Since diamondoid compounds are thermodynamically stable, they have potential applications in oil-source correlation and differentiation for cases where traditional biomarker terpanes and steranes are absent because of environmental weathering or refining of petroleum products. Although there is increased awareness of possible use of diamondoid compounds for source identification, there is no systematic approach for using these compounds. Quantitative surveys of the abundances of diamondoids are not available. Therefore, this study developed a reliable analytical method for quantitative diamondoid analysis. Gas chromatography/mass spectrometry (GC/MS) was used to quantitatively determine diamondoid compounds (adamantane, diamantane and their alkylated homologues) in 14 fresh crude oils and 23 refined petroleum products, including light and mid-range distillate fuels, residual fuels and lubricating oils collected from different sources. Results were compared with 2 types of biomarker compounds in oil saturated hydrocarbon fractions. Several diagnostic ratios of diamondoids were developed based on their concentrations. Their potential use for forensic oil spill source identification was evaluated. 24 refs., 8 tabs., 4 figs

Assessment of Appalachian basin oil and gas resources: Utica-Lower Paleozoic Total Petroleum System: Chapter G.10 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ryder, Robert T.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The Utica-Lower Paleozoic Total Petroleum System (TPS) in the Appalachian Basin Province is named for the Upper Ordovician Utica Shale, which is the source rock, and for multiple lower Paleozoic sandstone and carbonate units that are the important reservoirs. The total organic carbon (TOC) values for the Utica Shale are usually greater than 1 weight percent. TOC values ranging from 2 to 3 weight percent outline a broad, northeast-trending area that extends across western and southern Pennsylvania, eastern Ohio, northern West Virginia, and southeastern New York. The Utica Shale is characterized by type II kerogen, which is a variety of kerogen that is typically prone to oil generation. Conondont color-alteration index (CAI) isograds, which are based on samples from the Upper Ordovician Trenton Limestone (or Group), indicate that a pod of mature Utica Shale source rocks occupies most of the TPS.

U.S. Geological Survey Assessment of Undiscovered Petroleum Resources of the Hamra Basin, Libya, 2006

Science.gov (United States)

,

2007-01-01

The Hamra Basin Province encompasses approximately 244,100 square kilometers (94,250 square miles) and is entirely within Libya. One composite total petroleum system (TPS) was defined for this assessment; it extends from Libya westward into adjacent parts of Algeria and southern Tunisia. The Hamra Basin part of the TPS was subdivided into four assessment units for the purpose of resource assessment. The assessment units cover only 172,390 square kilometers of the Hamra Basin Province; the remaining area has little potential for undiscovered petroleum resources because of the absence of petroleum source rocks. Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean volumes of 784 million barrels of crude oil, 4,748 billion cubic feet of natural gas, and 381 million barrels of natural gas liquids in the Hamra Basin of northwestern Libya. Most of the undiscovered crude oil and natural gas are interpreted to be in deeper parts of the Hamra Basin.

Petroleum resources assessment 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

This report consists of two articles. (1) Petroleum resources assessment of the Okinawa Trough: The hydrocarbon potential has been evaluated for the Tertiary strata in the northwestern margin of the Okinawa Trough on the basis of the pale-ontological, petrological, geochemical data from two wells (Nikkan 8-9 and JDZ 7-3), and geophysical data. (2) Petroliferous basin analysis in Jinju area (2): Petroleum geological studies such as stratigraphy, sedimentology, petrology and organic geochemistry were carried out in the Gyeongsang Supergroup, Junju area. Based on lithofacies and rock color, the sequence can be divided into seven formations which can be organized into two groups (Sindong Group: Nagdong, Hasandong and Jinju formations in ascending order; Hayang Group: Chilgog, Silla Conglomerate, Haman and Jindong formations). (author). 57 refs.

Case studies using the United States Coast Guard's Oil Identification System for petroleum spill source identification

International Nuclear Information System (INIS)

Grosser, P.W.; Castellano, F.P.

1993-01-01

The Oil Identification System (OIS) was developed in the 1970's at the Coast Guard Research and Development Center, to determine the unique, intrinsic properties which would allow the matching of a spilled oil with its correct source. The Central Oil Identification Laboratory (COIL) was established in 1978 as the operating facility to implement the OIS. The OIS encompasses four analytical methods; thin layer chromatography, fluorescence spectroscopy, infrared spectroscopy and gas chromatography. A sample can be studied according to each individual method or multi-methods approach can be chosen if no single technique gives unequivocal results. Combined these methods are greater than 99% effective. The authors recently utilized the OIS and the COIL for three petroleum spill investigations in New York. As part of the investigation to determine the source(s) of several different petroleum product spills, OIS was conducted along with a review of groundwater sample chromatograms

Discovery and identification of a series of alkyl decalin isomers in petroleum geological samples.

Science.gov (United States)

Wang, Huitong; Zhang, Shuichang; Weng, Na; Zhang, Bin; Zhu, Guangyou; Liu, Lingyan

2015-07-07

The comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry (GC × GC/TOFMS) has been used to characterize a crude oil and a source rock extract sample. During the process, a series of pairwise components between monocyclic alkanes and mono-aromatics have been discovered. After tentative assignments of decahydronaphthalene isomers, a series of alkyl decalin isomers have been synthesized and used for identification and validation of these petroleum compounds. From both the MS and chromatography information, these pairwise compounds were identified as 2-alkyl-decahydronaphthalenes and 1-alkyl-decahydronaphthalenes. The polarity of 1-alkyl-decahydronaphthalenes was stronger. Their long chain alkyl substituent groups may be due to bacterial transformation or different oil cracking events. This systematic profiling of alkyl-decahydronaphthalene isomers provides further understanding and recognition of these potential petroleum biomarkers.

Application of a multimolecular marker approach to fingerprint petroleum pollution in the marine environment

International Nuclear Information System (INIS)

Barakat, Assem O.; Mostafa, Alaa R.; Rullkoetter, Juergen; Hegazi, Abdel Rahman

1999-01-01

In an attempt to investigate the suitability of a multibiological marker approach for defining the origin of petroleum pollution in marine systems, the aliphatic hydrocarbon composition of tar ball samples collected from the beaches of a small island impacted by heavy tar loads were determined by gas chromatography and gas chromatography/mass spectrometry. The tar ball samples, as collected, were at low stages of biodegradation and had diverse physical appearance. The majority of the samples (as many as 7 of the 10) appeared to be heavy fuel oils - possibly Bunker C. The GC traces for the other three tar balls, however, indicated that they were crude oils probably from tanker ballast washings or other non-point sources like the oil entering from the adjacent North Mediterranean. The biomarkers for the sterane and hopane series in these samples, however, had remained unaffected by weathering, and their distributions revealed significant differences among the samples suggesting multiple sources of the tar balls. The tar ball samples could be genetically subdivided into four groups on the basis of their biomarker fingerprints. A marine carbonate or evaporite, hypersaline, anoxic depositional environment of the petroleum source rock for Type I residues could be inferred from the even-carbon-number predominance of n-alkanes, the high relative abundance of gammacerane and the predominance of C 35 relative to C 34 17α(H)-homohopanes. Higher plant contribution and a deltaic environment of source rock deposition could be concluded for Type II residues from the high concentrations of oleanane and diasteranes. On the other hand, Type III residues possessed geochemical characteristics consistent with a normal marine carbonate or evaporite source depositional environment under normal saline, reducing conditions. Finally, type IV residues had biomarker signatures intermediate between Types II and III. (Author)

Geochemistry of Eagle Ford group source rocks and oils from the first shot field area, Texas

Science.gov (United States)

Edman, Janell D.; Pitman, Janet K.; Hammes, Ursula

2010-01-01

Total organic carbon, Rock-Eval pyrolysis, and vitrinite reflectance analyses performed on Eagle Ford Group core and cuttings samples from the First Shot field area, Texas demonstrate these samples have sufficient quantity, quality, and maturity of organic matter to have generated oil. Furthermore, gas chromatography and biomarker analyses performed on Eagle Ford Group oils and source rock extracts as well as weight percent sulfur analyses on the oils indicate the source rock facies for most of the oils are fairly similar. Specifically, these source rock facies vary in lithology from shales to marls, contain elevated levels of sulfur, and were deposited in a marine environment under anoxic conditions. It is these First Shot Eagle Ford source facies that have generated the oils in the First Shot Field. However, in contrast to the generally similar source rock facies and organic matter, maturity varies from early oil window to late oil window in the study area, and these maturity variations have a pronounced effect on both the source rock and oil characteristics. Finally, most of the oils appear to have been generated locally and have not experienced long distance migration. 

Characterizing the hypersiliceous rocks of Belgium used in (pre-)history: a case study on sourcing sedimentary quartzites

International Nuclear Information System (INIS)

Veldeman, Isis; Baele, Jean-Marc; De Doncker, H W J A; Goemaere, Eric; Deceukelaire, Marleen; Dusar, Michiel

2012-01-01

Tracking raw material back to its extraction source is a crucial step for archaeologists when trying to deduce migration patterns and trade contacts in (pre-)history. Regarding stone artefacts, the main rock types encountered in the archaeological record of Belgium are hypersiliceous rocks. This is a newly introduced category of rock types comprising those rocks made of at least 90% silica. These are strongly silicified quartz sands or sedimentary quartzites, siliceous rocks of chemical and biochemical origin (e.g. flint), very pure metamorphic quartzites and siliceous volcanic rocks (e.g. obsidian). To be able to distinguish between different extraction sources, ongoing research was started to locate possible extraction sources of hypersiliceous rocks and to characterize rocks collected from these sources. Characterization of these hypersiliceous rocks is executed with the aid of optical polarizing microscopy, optical cold cathodoluminescence and scanning-electron microscopy combined with energy-dispersive x-ray spectrometry and with back-scatter electron imaging. In this paper, we focus on various sedimentary quartzites of Paleogene stratigraphical level. (paper)

The use of nuclear energy for obtaining petroleum

International Nuclear Information System (INIS)

Waldmann, H.; Koch, C.; Thelen, H.J.; Kappe, P.

1982-01-01

After some basic considerations of petroleum demand, petroleum supply and petroleum reserves, the article gives a survey of the various methods of obtaining petroleum. The use of energy in the form of steam and electricity in the previously used processes and in conventional deposits requires up to 50% of the energy contained in the oil obtained. Now unconventional sources of petroleum (tertiary petroleum, heavy fractions and shale oil) could become of interest to West Germany in the near future. The economy of production can be determined by the energy source used, to a large extent. A series of possibilities are discussed for using nuclear steam raising systems for this purpose. (UA) [de

Hydrocarbon Source Rock Potential of the Sinamar Formation, Muara Bungo, Jambi

Directory of Open Access Journals (Sweden)

Moh. Heri Hermiyanto Zajuli

2014-07-01

Full Text Available DOI: 10.17014/ijog.v1i1.175The Oligocene Sinamar Formation consists of shale, claystone, mudstone, sandstone, conglomeratic sandstone, and intercalation of coal seams. The objective of study was to identify the hydrocarbon source rock potential of the Sinamar Formation based on geochemichal characteristics. The analyses were focused on fine sediments of the Sinamar Formation comprising shale, claystone, and mudstone. Primary data collected from the Sinamar Formation well and outcrops were analyzed according to TOC, pyrolisis analysis, and gas chromatography - mass spectometry of normal alkanes that include isoprenoids and sterane. The TOC value indicates a very well category. Based on TOC versus Pyrolysis Yields (PY diagram, the shales of Sinamar Formation are included into oil prone source rock potential with good to excellent categories. Fine sediments of the Sinamar Formation tend to produce oil and gas originated from kerogen types I and III. The shales tend to generate oil than claystone and mudstone and therefore they are included into a potential source rock. 

Dysfunctionalism in the Williston Basin: The Bakken/mid-Madison petroleum system

Energy Technology Data Exchange (ETDEWEB)

Price, L.C. (United States Geological Survey, Denver, CO (United States)); LeFever, J. (North Dakota Geological Survey, Grand Forks, ND (United States))

1994-06-01

Analyses of fifteen oils produced from fractured shales of the Upper Devonian and Lower Mississippian Bakken Formation in the Williston Basin were compared to the same analyses for eighteen Williston Basin oils produced from conventional reservoirs in the middle of the Lower and Upper Mississippian Madison Group. All oils came from the U.S. portion of the Williston Basin. These comparisons demonstrate that the Bakken and mid-Madison oils are different oil families from different source rocks. Within the saturated hydrocarbons (HCs) the Bakken oils are more naphthenic, less paraffinic, have different n-paraffin and isoprenoid-HC profiles, and have different compound ratios for 'generic' saturated HCs, as compared to the Madison oils. Within the aromatic HCs the mid-Madison oils have an unusual trimethylnaphthalene distribution, high concentrations of dibenzothiophenes and alkylated variants thereof, and different aromatic-HC peak distributions in general (and thus different aromatic-HC compound ratio plots), as compared to the Bakken oils. Because of wide maturity ranges in both oil sets, biomarkers were of limited utility as source-facies indices and thus correlation tools. No oil has yet been found to be generated by the Bakken shales or any mixing of Bakken and Madison oils in a Madison reservoir. It is believed the range of variation in the correlation indices is too large among the Madison oils for these oils to have a single source rock. It is hypothesized that the Madison oils are from separate source rocks interbedded with the different mid-Madison reservoirs in the basin, rocks which appear to have the same, or very similar, depositional environments. Thus the original Bakken/mid-Madison petroleum system appears dysfunctional. 55 refs., 30 figs., 7 figs.

Petroleum generation 3D modeling of Espirito Santo Basin, Brazil; Modelagem 3D da geracao de petroleo na Bacia do Espirito Santo, Brasil

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Daniella A.; Lemgruber, Adriana; Goncalves, Felix T.T. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Lab. de Modelagem Multidisciplinar de Bacias Sedimentares (LAB2M); Petersohn, Eliane [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

2008-07-01

Intervals of potential source rocks were identified and characterized by the analysis and interpretation of total organic carbon (TOC) and Rock-Eval pyrolysis data. The rift section presents the best conditions for hydrocarbon generation, especially in Mariricu formation, that presents high TOC, hydrogen index and type I Kerogen. The drift section possesses low source rock potential, the intervals with best organic matter characteristic (quantity and quality) are represented by thin packages positioned in the superior portion of Regencia and Sao Mateus formation and in the basis of Urucutuca formation. The geochemistry data was integrated, on a regional scale, into the thermal maturation and petroleum generation three-dimensional model. Four potentially source rock intervals were simulated, two in the pre-salt section and two in the post-salt section. The results point out that the pre-salt intervals have reached thermal maturity in the proximal shelf and were overmatured in deep water. The thermal evolution obtained for the post-salt zone was very similar to those obtained for the rift section (pre-salt section). (author)

Trace element characterisation of Cretaceous Orange Basin hydrocarbon source rocks

International Nuclear Information System (INIS)

Akinlua, A.; Adekola, S.A.; Swakamisa, O.; Fadipe, O.A.; Akinyemi, S.A.

2010-01-01

Research highlights: → Vanadium and nickel contents indicate that the rock samples from the Orange Basin have marine organic matter input. → The organic matter of the Orange Basin source rocks were deposited in reducing conditions. → Despite the similarities in the organic matter source input and depositional environment of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal their subtle differences. → Cluster analysis classified the samples into three groups based on subtle differences in their .thermal maturity. - Abstract: Trace elements in the kerogen fraction of hydrocarbon source rock samples from two wells obtained from the Cretaceous units of the Orange Basin, South Africa were determined using X-ray fluorescence spectrometry, in order to determine their distribution and geochemical significances. The concentrations of the elements (As, Ce, Co, Cu, Fe, Mo, Ni, Pb and V) determined ranged from 0.64 to 47,300 ppm for the samples analysed. The total organic carbon (TOC) values indicate that the samples are organic rich but did not show any trend with the distribution of the trace metals except Ce, Mo and Pb. Dendrogram cluster analysis discriminated the samples into three groups on the basis of their level of thermal maturity. Thermal maturity has a significant effect on the distribution of the trace metals. Cobalt/Ni and V/Ni ratios and cross plots of the absolute values of V and Ni indicate that the samples had significant marine organic matter input. The V and Ni contents and V/(V + Ni) ratio indicate that the organic matter of the source rocks had been deposited in reducing conditions. Despite the similarities in the organic matter source input and depositional environment of the organic matter of the samples from the two well, cross plots of Co/Ni versus V/Ni and Mo/Ni versus Co/Ni were able to reveal subtle differences. Cluster analysis of the samples was also able to reveal the subtle

Assessment of undiscovered conventionally recoverable petroleum resources of the Northwest European region

Science.gov (United States)

Masters, Charles D.; Klemme, H. Douglas

1984-01-01

The estimates of undiscovered conventionally recoverable petroleum resources in the northwest European region at probability levels of 95 percent, 5 percent, statistical mean, and mode are for oil (in billions of barrels): 9, 34, 20, and 15; and for gas (in trillions of cubic feet): 92, 258, 167, and 162. The occurrence of petroleum can be accounted for in two distinct geological plays located in the various subbasins of the region. Play I is associated with the distribution of mature source rocks of Late Jurassic age relative to four distinct trapping conditions. The play has been demonstrated productive mostly in the Viking and Central Grabens of the North Sea, where the shale has been buried to optimum depths for the generation of both oil and gas. To the north of 62 ? N. latitude up to the Barents Sea, source rocks become increasingly deeply buried and are interpreted to be dominantly gas prone; a narrow band of potentially oil-prone shales tracks most of the coast of Norway, but water depths in favorable localities commonly range from 600 to 1,200 feet. To the south of the Central Graben, the Jurassic source rocks are either immature or minimally productive because of a change in facies. Undrilled traps remain within the favorable source-rock area, and exploration will continue to challenge the boundaries of conventional wisdom, especially on the Norwegian side where little has .been reported on the geology of the adjoining Bergen High or Horda Basin, though, reportedly, the Jurassic source rocks are missing on the high and are immature in the southern part of the basin. Play II is associated with the distribution of a coal facies of Carboniferous age that is mature for the generation of gas and locally underlies favorable reservoir and sealing rocks. The play is limited largely by facies development to the present area of discovery and production but is limited as well to the southeast into onshore Netherlands and Germany by the unfavorable economics of an

Depositional environments and oil potential of Jurassic/Cretaceous source rocks within the Seychelles microcontinent

Energy Technology Data Exchange (ETDEWEB)

Plummer, P.S.; Joseph, P.R.; Samson, P.J. [Seychelles National Oil Co., Mahe (Seychelles)

1998-12-31

The Seychelles microcontinent became isolated between the Somali, Mascarene and Arabian basins of the Indian Ocean as a result of the Mesozoic fragmentation of Gondwana. Major rifting events occurred during the Triassic-Middle Jurassic and Late Cretaceous (Cenomanian-Santonian and Maastrichtian) during which shaly source rock facies accumulated in principally marginal marine/deltaic environments. Between these times, post-rift passive margin deposition within restricted to open marine environments produced shaly source rocks during late Middle Jurasic-Early Cretaceous, Campanian-Maastrichtian and Paleocene times. Recent geochemical analysis of cuttings from the Seagull Shoals-1 well has identified an oil-prone liptinitic (Type II) coaly shale within early Middle Jurassic abandoned deltaic deposits. This coaly source rock is regionally developed, having also been identified in the Majunja and Morondava basins of Madagascar. Oil-prone Type II organic matter has also been identified in the Owen Bank A-1 well within restricted marine shales of late Middle Jurassic age. These shales are part of a thick post-rift source rock sequence that extends into the Early Cretaceous and is in part correlative with the proven Late Jurassic Uarandab Shale of Somalia. Analysis of Campanian marine shales from Reith Bank-1 well identified significant dilution of total organic carbon content in composite, compared to picked, well cuttings samples. This finding supports a published inference that these post-rift shales have source rock potential. (author)

Organic Geochemistry of the Cenomanian-Turonian Bahloul Formation Petroleum Source Rock, Central and Northern Tunisia

OpenAIRE

Affouri , Hassene; Montacer , Mabrouk; Disnar , Jean-Robert

2013-01-01

International audience; Total organic carbon (TOC) determination, Rock-Eval pyrolysis, extractable organic matter content (EOM) fractionation, gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS) analyses, were carried out on 79 samples from eleven outcrop cross sections of the Bahloul Formation in central and northern Tunisia. The TOC content varied between 0.23 to 35.6%, the highest average values (18.73%, 8.46% and 4.02%) being at the east of the study area (at Ain Zakk...

Hydrocarbon source rock potential evaluation of the Late Paleocene ...

Indian Academy of Sciences (India)

63

research is available on its source rock potential evaluation at Nammal Gorge Section in the Salt. Range, Potwar Basin .... methods of Tucker (2003) and Assaad (2008) have been followed. A total of fifteen ..... Business Media. Baker D M, Lillie ...

Alternative designs for petroleum product storage tanks for groundwater protection.

Science.gov (United States)

Oke Adeleke, Samson

In developing countries, there are numerous occurrences of petroleum product spillage in groundwater. The current practice of burying storage tanks beneath the surface without adequate safety devices facilitates this phenomenon. Underground tanks rust and leak, and spilled petroleum products migrate downward. The movement of the oil in the soil depends on its viscosity and quantity, the permeability of the soil/rock, and the presence of fractures within the rock. The oil spreads laterally in the form of a thin pancake due to its lower specific gravity, and soluble components dissolve in water. The pollution plume of petroleum products and dissolved phases moves in the direction of groundwater flow in the aquifer within the pores of soil and sediments or along fractures in basement complex areas. Most communities reply heavily on groundwater for potable and industrial supplies. However, the sustainability of this resource is under threat in areas where there are filling stations as a result of significant groundwater contamination from petroleum product spillage. Drinking water becomes unpalatable when it contains petroleum products in low concentrations, and small quantities may contaminate large volumes of water. Considering the losses incurred from spillage, the cost of cleaning the aquifer, and the fact that total cleansing and attenuation is impossible, the need to prevent spillage and if it happens to prevent it from getting into the groundwater system is of paramount importance. This paper proposes alternative design procedures with a view to achieving these objectives.

The use of polynuclear aromatic hydrocarbon (PAH) alkyl homologues in determining petroleum source identification and weathering

International Nuclear Information System (INIS)

Brown, J.S.; Boehm, P.D.; Sauer, T.C.; Wong, W.M.C.

1993-01-01

Techniques utilizing double ratio plots of selected polynuclear aromatic hydrocarbon (PAH) alkyl homologues were used to identify and distinguish crude oils and refined petroleum products from each other and to distinguish petroleum sources in complex pollutant regimes. Petroleum samples were fractionated by high performance liquid chromatography (HPLC) into saturated and aromatic (PAH) hydrocarbon fractions. The saturated hydrocarbon fractions were then analyzed by gas chromatography/flame ionization detection (GC/FID) to obtain a resolved/unresolved alkane fingerprint of each oil. The aromatic fractions of the oils were analyzed by gas chromatography/mass spectrometry (GC/MS) for PAH and selected alkyl homologues. Comparisons of the saturated hydrocarbon fingerprints indicated that some oils were indistinguishable based on the alkane fingerprint alone. Another double ratio plot of the alkyl chrysenes and alkyl dibenzothiophenes was effective in establishing the weathering of oil in environmental samples which were processed using the same analytical techniques, since the dibenzothiophenes are degraded more rapidly than the chrysenes. The application of selected ratios in oil spill source identification in complex environmental samples from Suisin Bay California and Boston Harbor are discussed. The use of ratios to measure the extent of weathering in oil spill samples from Prince William Sound and the Gulf of Alaska is examined

Mathematical modelling on transport of petroleum hydrocarbons

Indian Academy of Sciences (India)

A brief theory has been included on the composition and transport of petroleum hydrocarbons following an onshore oil spill in order to demonstrate the level of complexity associated with the LNAPL dissolution mass transfer even in a classical porous medium. However, such studies in saturated fractured rocks are highly ...

Petroleum migration and mixing in the Pearl River Mouth Basin, South China Sea

Energy Technology Data Exchange (ETDEWEB)

Chunming Zhang [Jianghan Petroleum Univ., Geochemistry Research Center, Jingzhou, Hubei (China); China Univ. of Geosciences, Dept. of Energy Resources, Beijing (China); Sitian Li [China Univ. of Geosciences, Dept. of Energy Resources, Beijing (China); Jiaming Yang [China National Offshore Oil Corp., Beijing (China); Shaokun Yang; Jianrong Wang [Nanhai East Oil Co., Research Inst., Guangzhou (China)

2004-02-01

Two oil groups have been investigated in the Pearl River Mouth Basin using their geochemical characteristics. In combination with source data, the two oil groups may be extrapolated into two end-member oils: petroleum populations A and B. The oil population A with abundant 4-methylsteranes, derived from the deeper Wenchang source rocks, migrated and accumulated earlier. The oil population B with absent 4-methylsteranes was expelled from the Enping source rocks and is associated with a relatively later phase of migration and accumulation. The two distinctive oil populations migrated updip through the marine blanket-like sandstone carriers within the Zhuhai Formation to accumulate in a series of traps along the main migration pathways at different times. Most of the accumulations are mixtures of the two end-member oils. The variations of 4-methylsterane concentrations in the accumulations can be related to the contributions from the two sources: the oils, which migrated furthest, contain greater contributions from the Wenchang source rocks, whereas those with shorter migration paths have greater contributions from the Enping sources. The later migrated oils closer to the depression areas are highly mature and the former oils in the Liuhua oil fields are of relatively low maturity, which may indicate the main migration direction along the Hui-Liu Structure Ridge (HLSR). Oils with abnormally high maturity in the middle of the HLSR may suggest oil-filling points, from which branch conduits connected the source kitchens to the main migration pathway. Oils with abnormally low maturities may reveal minor contributions from some small sags in the Dongsha Massif in a later phase. (Author)

On the source material of magmas - with special reference to Nd isotopic ratios of igneous rocks

International Nuclear Information System (INIS)

Shuto, Kenji

1980-01-01

In 1973, the Sm-Nd method was first used for the measurement of the absolute age of igneous rocks and meteorites. Subsequently in the following years, the research works by means of the Nd isotopic ratio in igneous rocks have been made strenuously in order to reveal the chemistry of the source materials of magma giving rise to the igneous rocks and further the evolution process of mantle and earth's crust. The fundamental items for the Sm-Nd method are explained. Then, the research results more important in the above connection are given. Finally, the ideas by the author concerning the source materials of magma are presented from the data available on the Nd isotopes in meteorites and igneous rocks. The following matters are described: the fundamentals of Sm-Nd method, the Nd content in seawater, the negative correlation between Nd and Sr isotopic ratios in igneous rocks, magma source materials and Nd isotopes, and considerations on magma source materials. (J.P.N.)

Applying Bioaugmentation to Treat DNAPL Sources in Fractured Rock

Science.gov (United States)

2017-03-27

Figure 1. This ESTCP demonstration was focused in the vicinity of Building 8595, adjacent to the location of a reported surface release of PCE ( Earth ...electron donor source, such as vegetable oil, is typically used in passive approaches. When treating a DNAPL source area in fractured rock, there are... vegetable oil) are used. Hydrogen The generation of hydrogen can be used to verify fermentation of electron donor. Metals (Fe, Mn, As) Increase

Summary of regional geology, petroleum potential, resource assessment and environmental considerations for oil and gas lease sale area No. 56

Science.gov (United States)

Dillon, William P.; Klitgord, Kim D.; Paull, Charles K.; Grow, John A.; Ball, Mahlon M.; Dolton, Gordon L.; Powers, Richard B.; Khan, Abdul S.; Popenoe, Peter; Robb, James M.; Dillon, William P.

1980-01-01

This report summarizes our general knowledge of the petroleum potential, as well as problems and hazards associated with development of petroleum resources in the area proposed for nominations for lease sale number 56. This area includes the U.S. eastern continental margin from the North Carolina-Virginia border south to approximately Cape Canaveral, Florida and from three miles from shore, seaward to include the upper Continental Slope and inner Blake Plateau. The area for possible sales is shown in figure 1; major physiographic features of the region are shown in figure 2.No wells have been drilled for petroleum within this proposed lease area and no significant commercial production has been obtained onshore in the Southeast Georgia Embayment. The COST GE-1 stratigraphic test well, drilled on the Continental Shelf off Jacksonville, Fla. (fig- 1), reached basement at 3,300 m. The bottom third of the section consists of dominantly continental rocks that are typically poor sources of petroleum (Scholle, 1979) and the rocks that contain organic carbon adequate for generation of petroleum at the well are seen in seismic profiles always at shallow subbottom depths, so they probably have not reached thermal maturity. However, seismic profiles indicate that the sedimentary deposits thicken markedly in a seaward direction where more of the section was deposited under marine conditions; therefore, commercial accumulations of petroleum offshore are more likely.Several potential sources of environmental hazard exist. Among the most important are hurricanes, the Gulf Stream, and earthquakes. The potential danger from high wind, waves, storm surges, and storm-driven currents associated with hurricanes is obvious. Evidence for significant bottom scour by the Gulf Stream is abundant; such scour is a threat to the stability of bottom-mounted structures. The fast-flowing water also will hamper floating drill rigs and control of drill strings. A major earthquake of about magnitude

Water isotopic characterization of hypersaline formation of a petroleum field Reconcavo basin, Brazil

International Nuclear Information System (INIS)

Teles, Danilo Ribeiro de Sa; Azevedo, Antonio Expedito Gomes de

2010-01-01

Formation water is the water present in reservoir rock pores, produced together with petroleum. Usually it is hyper saline with concentrations that can be higher than 250 g/l of dissolved solids. The concentration of the dissolved elements and the isotopic composition of the water and of some of the dissolved elements can be excellent tracers to study the dynamic of underground fluid flux, the mixing of distinct sources and the origin of salinization of these waters. This work reports the isotopic composition (δ 2 H , δ 18 O) and electrical conductivity (EC) of formation waters from 10 wells of a petroleum field of the Reconcavo Basin, looking for their evolution, interaction with the minerals and rocks and reservoir interconnection. The samples have electric conductivity ranging from 84 to 137 mS/cm, with conductivity increasing with depth of production zone. It is observed an enrichment of deuterium and oxygen-18 with the depth of production zone, probably due to water-rock interactions that were probably increased by higher temperatures of the deeper levels and longer residence times. The samples from the production zone between 1450 to 1520 m, drained by 7 of the 10 wells sampled, show a small range in isotopic composition and in electric conductivity, indicating homogeneity in this level of the reservoir. In the shallow level of 450 m the values of δ 2 H , δ 18 O and EC are lower, with isotopic composition similar to the oceanic water, possibly representing the original water that entered the reservoir during the sedimentation of the basin. (author)

Total porosity of carbonate reservoir rocks by X-ray microtomography in two different spatial resolutions

International Nuclear Information System (INIS)

Nagata, Rodrigo; Appoloni, Carlos R.; Marques, Leonardo C.; Fernandes, Celso P.

2011-01-01

Carbonate reservoir rocks contain more than 50% of world's petroleum. To know carbonate rocks' structural properties is quite important to petroleum extraction. One of their main structural properties is the total porosity, which shows the rock's capacity to stock petroleum. In recent years, the X-ray microtomography had been used to analyze the structural parameters of reservoir rocks. Such nondestructive technique generates images of the samples' internal structure, allowing the evaluation of its properties. The spatial resolution is a measurement parameter that indicates the smallest structure size observable in a sample. It is possible to measure one sample using two or more different spatial resolutions in order to evaluate the samples' pore scale. In this work, two samples of the same sort of carbonate rock were measured, and in each measurement a different spatial resolution (17 μm and 7 μm) was applied. The obtained results showed that with the better resolution it was possible to measure 8% more pores than with the poorer resolution. Such difference provides us with good expectations about such approach to study the pore scale of carbonate rocks. (author)

40Ar/39Ar geochronology of hypabyssal igneous rocks in the Maranon Basin of Peru - A record of thermal history, structure, and alteration

Science.gov (United States)

Prueher, L.M.; Erlich, R.; Snee, L.W.

2005-01-01

Hypabyssal andesites and dacites from the Balsapuerto Dome in the Mara?on Basin of Peru record the thermal, tectonic, and alteration history of the area. The Mara?on Basin is one of 19 sub-Andean foreland basins. The hypabyssal rocks in the Balsapuerto Dome are one of four known occurrences of subvolcanic rocks along the deformation front in Peru. This dome is a potential petroleum structural trap. Petroleum seeps near the dome indicate that a source for the petroleum is present, but the extent and amount of petroleum development is unknown. The Balsapuerto hypabyssal rocks are plagioclase-, hornblende-, pyroxene-phyric andesites to dacites. Some parts of the dome are pervasively altered to a hydrothermal assemblage of quartz-sericite-pyrite. 40Ar/39Ar geochronology shows that thermal activity related to emplacement of these subvolcanic rocks took place between 12-10 Ma, subsequent to the major periods of Andean folding and faulting, previously assumed to have occurred about 9 Ma. Eleven argon mineral age-spectrum analyses were completed. Argon apparent ages on amphibole range from 12.7 to 11.6 Ma, and the age spectra are simple, which indicates that the ages are very close to emplacement ages. Potassium feldspar yields an argon age spectrum ranging in age from 12.5 to 11.4 Ma, reflecting the period during which the potassium feldspar closed to argon diffusion between the temperature range of 350?C to about 150?C; thus the potassium feldspar age spectrum reflects a cooling profile throughout this temperature range. This age range is consistent with ages of emplacement for the entire igneous complex indicating that an increased thermal state existed in the area for at least 1.0 m.y. Combined with the coexisting hornblende age, this rock cooled from ~580?C to ~150?C in ~1.2 m.y. resulting in an average cooling rate of 358?C /m.y. White mica, or sericite, formed as a later alteration phase associated with quartz- sericite- pyrite and propylitic alteration in some

The oil potential of the BM-J-2 block, Jequitinhonha basin, Brazil: the integrated study of the basin analysis and modeling of petroleum system; Potencial petrolifero do Bloco BM-J-2, Bacia de Jequitinhonha, Brasil: um estudo integrado de analise de bacia e modelagem de sistemas petroliferos

Energy Technology Data Exchange (ETDEWEB)

Porto, Roberto; Braga, Jose A.E.; Saito, Makoto; Cortez, Marcella; Ponte Filho, Francisco C.; Romao, Felipe [Queiroz Galvao Perfuracoes S.A., Rio de Janeiro, RJ (Brazil); Goncalves, Felix T.T. [PGT-Petroleum Geoscience Technology Ltd., Rio de Janeiro, RJ (Brazil)

2004-07-01

The integration of all available geochemical data from this and adjoining blocks (BM-J-1 e BM-J-3) Jequitinhonha Basin revealed that only the Albian-Turonian and Aptian sections contains potential hydrocarbon source rock intervals. The existence of an oil accumulation (1-BAS-37) represents an unequivocal evidence of the presence of effective source rocks in the Jequitinhonha Basin. The geochemical characteristics of this oil accumulation points to an origin related to petroleum source rocks deposited under a lacustrine/marine restricted (hyper saline) environment. Such characteristics are typical of pre-salt Aptian source rocks in several basins along the Brazilian margin. The pseudo-3D modeling results indicate that the stage of thermal evolution of the base of the rift section attained ranges from early mature (0.6-0.8 Ro) in the structural highs to over mature (up to 2.0% Ro) in the structural lows On the other hand, the potential sources rocks of Albian-Turonian age ranges to immature to early mature throughout the block. The modeling results also points to the existence of two distinct hydrocarbon 'kitchens': one located in the easternmost portion of the block (slope/deep water area) and the other in a structural low located in the shallow platform area. The main phase of petroleum expulsion ranged from Late Cretaceous/Paleogene in the platform area. Probabilistic simulations has estimated migrated oils and gas volumes around 507 MMbbl and 20 billion cubic meters, respectively. (author)

Taxation of petroleum products: theory and empirical evidence

International Nuclear Information System (INIS)

Gupta, S.; Mahler, W.

1995-01-01

The domestic taxation of petroleum products is an important source of revenue in most countries. However, there is a wide variation of tax rates on petroleum products across countries, which cannot be explained by economic theory alone. This paper surveys different considerations advanced for taxing petroleum and presents petroleum tax rate data in 120countries. (author)

Relationship between fluvial clastic sediment and source rock abundance in Rapti river basin of central Nepal Himalayas

International Nuclear Information System (INIS)

Tamrakar Naresh Kazi; Shresth Madhusudan Bhakta

2008-01-01

Many tributaries from carbonate sedimentary, metamorphic and igneous rocks of the Lesser Himalayan and clastic sedimentary rocks of the Sub-Himalayan Ranges carry gravelly sediments to the Rapti River. River bar sediments were analyzed for composition and texture to evaluate downstream changes in properties, and to establish relationship between proportion of clasts and the abundance of rock types in the source areas. Percent quartzite clast or granite clast increases whereas that of carbonate, schist or slate decreases along downstream. The largest grain size decreases downstream, whereas fatness index and sphericity tend to increase. Despite of little diminish in relative abundance of rock types in source areas along the river, the relative proportion of corresponding clast type shows rapid reduction (e.g. slate or phyllite or carbonate clasts) or rapid enhancement (e.g. granite clast). The relationships of quartzite clast and schist clasts with their corresponding source rocks are statistically significant suggesting that these clasts can provide clue to source rock abundance. About 85 to 94% of the gravel clasts represent rock types of the Lesser Himalayan Range suggesting that this range has been contributing enormous amount of sediments.

Osmium Isotopic Evolution of the Mantle Sources of Precambrian Ultramafic Rocks

Science.gov (United States)

Gangopadhyay, A.; Walker, R. J.

2006-12-01

The Os isotopic composition of the modern mantle, as recorded collectively by ocean island basalts, mid- oceanic ridge basalts (MORB) and abyssal peridotites, is evidently highly heterogeneous (γ Os(I) ranging from +25). One important question, therefore, is how and when the Earth's mantle developed such large-scale Os isotopic heterogeneities. Previous Os isotopic studies of ancient ultramafic systems, including komatiites and picrites, have shown that the Os isotopic heterogeneity of the terrestrial mantle can be traced as far back as the late-Archean (~ 2.7-2.8 Ga). This observation is based on the initial Os isotopic ratios obtained for the mantle sources of some of the ancient ultramafic rocks determined through analyses of numerous Os-rich whole-rock and/or mineral samples. In some cases, the closed-system behavior of these ancient ultramafic rocks was demonstrated via the generation of isochrons of precise ages, consistent with those obtained from other radiogenic isotopic systems. Thus, a compilation of the published initial ^{187}Os/^{188}Os ratios reported for the mantle sources of komatiitic and picritic rocks is now possible that covers a large range of geologic time spanning from the Mesozoic (ca. 89 Ma Gorgona komatiites) to the Mid-Archean (e.g., ca. 3.3 Ga Commondale komatiites), which provides a comprehensive picture of the Os isotopic evolution of their mantle sources through geologic time. Several Precambrian komatiite/picrite systems are characterized by suprachondritic initial ^{187}Os/^{188}Os ratios (e.g., Belingwe, Kostomuksha, Pechenga). Such long-term enrichments in ^{187}Os of the mantle sources for these rocks may be explained via recycling of old mafic oceanic crust or incorporation of putative suprachondritic outer core materials entrained into their mantle sources. The relative importance of the two processes for some modern mantle-derived systems (e.g., Hawaiian picrites) is an issue of substantial debate. Importantly, however, the

A simple source preparation method for alpha-ray spectrometry of volcanic rock sample

International Nuclear Information System (INIS)

Takahashi, Masaomi; Kurihara, Yuichi; Sato, Jun

2006-01-01

A simple source preparation method was developed for the alpha-ray spectrometry to determine U and Th in volcanic rockes. Isolation of U and Th from volcanic rocks was made by use of UTEVA-Spec. resin, extraction chromatograph material. U and Th were extracted by TTA-benzene solution and organic phase was evaporated drop by drop on a hot stainless steel planchet to dryness. This method was found to be effective for the preparation of sources for alpha-ray spectrometry. (author)

Scientific results from the deepened Lopra-1 borehole, Faroe Islands: Petroleum geochemistry of the deepened Lopra-1/1A re-entry well, Faroe Islands

Directory of Open Access Journals (Sweden)

Nytoft, H. Peter

2006-07-01

Full Text Available The Lopra-1/1A re-entry well was drilled as a stratigraphic test with no immediate exploration objectives. Hence, petroleum geochemical studies were of limited extent, and restricted to non-destructive analyses. The presence of natural petroleum hydrocarbons could not be confirmed with certainty, but hydrocarbons extracted from the hydrochloric acid solute of a calcite vug present in RSWC #1 (3543 m, may represent indigenous petroleum since hydrocarbon-bearing fluid inclusions have been reported from the same sample. These hydrocarbons show some similarities to petroleum generatedfrom the Upper Jurassic – Lower Cretaceous Kimmeridge Clay type source rocks present in surrounding areas. Except for this sample, the results generally show the presence of a variety of contaminantsof different origins such as ‘naturally greasy fingers’ (squalene and cholesterol, cosmetics such as chap stick or hand lotion (e.g. esters such as butyl-stearate, stearyl-palmitate, vitamin A, plasticisers (phthalates, diesel oil and ‘pipe dope’.

Identifying the source of petroleum pollution in sediment cores of southwest of the Caspian Sea using chemical fingerprinting of aliphatic and alicyclic hydrocarbons.

Science.gov (United States)

Shirneshan, Golshan; Bakhtiari, Alireza Riyahi; Memariani, Mahmoud

2017-02-15

In this study, the concentration and sources of aliphatic and petroleum markers were investigated in 105 samples of Anzali, Rezvanshahr and Astara cores from the southwest of Caspian Sea. Petroleum importation was diagnosed as a main source in most depths of cores by the results of unresolved complex mixture, carbon preference index and hopanes and steranes. From the chemical diagnostic parameters, petroleum inputs in sediment of cores were determined to be different during years and the sources of hydrocarbons in some sections differed than Anzali and Turkmenistan and Azerbaijan oils. Diagenic ratios in most sediments of upper and middle sections in Astara core were determined to be highly similar to those of Azerbaijan oil, while the presence of Turkmenistan and Anzali oils were detected in a few sections of Anzali and Rezvanshahr cores and only five layers of downer section in Anzali core, respectively. Copyright © 2016. Published by Elsevier Ltd.

Petroleum: An energy profile, 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

This report prepared by the Energy Information Administration covers the following topics: petroleum production and end-use sectors; resources and reserves; exploration and production; LPG sources and processing; motor gasoline octane enhancement; constructing pipelines; the strategic petroleum reserve; imports and exports; marketing; district descriptions and maps; and refinery processes and facilities. 33 figs., 7 tabs.

Interpretation of Oil Seepage of Source Rock Based Magnetic Survey in Cipari Cilacap District

Directory of Open Access Journals (Sweden)

Sukmaji Anom Raharjo

2015-12-01

Full Text Available The magnetic survey had been conducted in Village of Cipari, District of Cipari, Region of  Cilacap to interpret to the location of the oil seepage source rock. Boundary of the research area is 108.75675°E – 108.77611°E and 7.42319°S – 7.43761°S. The observed total magnetic data is corrected and reducted to obtain the local magnetic anomaly data. The local magnetic anomaly data is applied to model the subsurface bodies anomalies based on the Mag2DC for Windows software. With be supported the geological information, the some bodies anomalies are interpreted as the basaltic igneous rock (c = 0.0051, the alternately of sandstone and claystone and insert of marl from Halang Formation (c = 0.0014, the breccia from Kumbang Formation (c = 0.0035, the alternately of sandstones and claystone with insert of marl and breccia from Halang Formation (c = 0.0036, the claystone from Tapak Formation (c = 0.0015, the alternately of sandstones and claystone with insert of marl and compacted breccia from Halang Formation (c = 0.0030, and the alternately of sandstone and claystone from   Halang Formation (c = 0.0020. The plantonic foraminifer fossils as resources of oil seepage are estimated in the sedimentaries rocks, where the oil flows from those rocks into the         reservoir (source rock. Based on the interpretation results, the source rock is above basaltic igneous rock with the approximate position is 108.76164°W and 7.43089°S; and the depth is 132.09 meters below the average topographic.

Petroleum supply annual 1992

International Nuclear Information System (INIS)

1993-01-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1992 through annual and monthly surveys. The PSA is divided into two volumes. The first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. This second volume contains final statistics for each month of 1992, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary

Geology and oil and gas assessment of the Fruitland Total Petroleum System, San Juan Basin, New Mexico and Colorado: Chapter 6 in Geology and Oil and Gas Assessment of the Fruitland Total Petroleum System, San Juan Basin, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Condon, S.M.; Hatch, J.R.

2013-01-01

The Fruitland Total Petroleum System (TPS) of the San Juan Basin Province includes all genetically related hydrocarbons generated from coal beds and organic-rich shales in the Cretaceous Fruitland Formation. Coal beds are considered to be the primary source of the hydrocarbons. Potential reservoir rocks in the Fruitland TPS consist of the Upper Cretaceous Pictured Cliffs Sandstone, Fruitland Formation (both sandstone and coal beds), and the Farmington Sandstone Member of the Kirtland Formation, and the Tertiary Ojo Alamo Sandstone, and Animas, Nacimiento, and San Jose Formations.

Reexamination of the source material of acid igneous rocks, based on the selected Sr isotopic data

International Nuclear Information System (INIS)

Kagami, Hiroo; Shuto, Kenji; Gorai, Masao

1975-01-01

The relation between the ages and the initial strontium isotopic compositions obtained from acid igneous rocks by the whole-rock isochron method is re-examined, on the basis of the selected data. The points based on the data having high values of standard deviation (on the isochrons) show considerable scattering. This is probably ascribed to admixture of sialic materials, or secondary alteration and other geologic causes. The points based on the data having lower values of standard deviation (sigma value: 0.0001 - 0.0019), on the other hand, are evidently plotted within a narrow region just above the presumed Sr evolutional region of the source material of oceanic tholeiites. It is noteworthy that the former region meets the latter region at an earlier stage of the evolutional history of the earth (about 40 x 10 8 yrs. ago or older). It may be conceivable that the former region is the Sr evolutional region of the source material of acid igneous rocks. Considering from the inclination of the above Sr evolutional region, the source material of most of acid igneous rocks may possibly be a certain basic material, chemically similar to the continental tholeiitic basalts or basaltic andesites. On the other hand, the source material of a few acid igneous rocks with low initial strontium isotopic ratios may be a certain basic material resembling the oceanic tholeiites. Another possibility is that these acid igneous rocks and oceanic tholeiites may have been formed, under different physical conditions, directly from a certain common source material presumably of peridotitic composition. (auth.)

Crustal contamination versus an enriched mantle source for intracontinental mafic rocks: Insights from early Paleozoic mafic rocks of the South China Block

Science.gov (United States)

Xu, Wenjing; Xu, Xisheng; Zeng, Gang

2017-08-01

Several recent studies have documented that the silicic rocks (SiO2 > 65 wt.%) comprising Silicic Large Igneous Provinces are derived from partial melting of the crust facilitated by underplating/intraplating of "hidden" large igneous province-scale basaltic magmas. The early Paleozoic intracontinental magmatic rocks in the South China Block (SCB) are dominantly granitoids, which cover a combined area of 22,000 km2. In contrast, exposures of mafic rocks total only 45 km2. These mafic rocks have extremely heterogeneous isotopic signatures that range from depleted to enriched (whole rock initial 87Sr/86Sr = 0.7041-0.7102; εNd(t) = - 8.4 to + 1.8; weighted mean zircon εHf(t) = - 7.4 to + 5.2), show low Ce/Pb and Nb/U ratios (0.59-13.1 and 3.5-20.9, respectively), and variable Th/La ratios (0.11-0.51). The high-MgO mafic rocks (MgO > 10 wt.%) tend to have lower εNd(t) values (- 4) and Sm/Nd ratios (> 0.255). The differences in geochemistry between the high-MgO and low-MgO mafic rocks indicate greater modification of the compositions of high-MgO mafic magmas by crustal material. In addition, generally good negative correlations between εNd(t) and initial 87Sr/86Sr ratios, MgO, and K2O, along with the presence of inherited zircons in some plutons, indicate that the geochemical and isotopic compositions of the mafic rocks reflect significant crustal contamination, rather than an enriched mantle source. The results show that high-MgO mafic rocks with fertile isotopic compositions may be indicative of crustal contamination in addition to an enriched mantle source, and it is more likely that the lithospheric mantle beneath the SCB during the early Paleozoic was moderately depleted than enriched by ancient subduction processes.

Petroleum and geopolitics; Petrole et geopolitique

Energy Technology Data Exchange (ETDEWEB)

Chaigneau, P. [Centre d' etudes diplomatiques et strategiques de Paris, 75 (France)

2004-04-01

Todays, petroleum companies consider that despite the constant increase of petroleum consumption, petroleum will remain the main energy source for at least 40 years. However, after the Iraq conflict, new regional situations are changing. China, for instance, with its growing up demand, will change the physiognomy of the oil market. In parallel, from Indonesia to Africa, petroleum and religion interfere and explain the new conflict areas. As for the US strategy, which is not limited to the energy paradigm, it largely integrates energy in the main lines of its diplomacy, from the 'Wide Middle East' to the 'Sahel initiative', and in its position with respect to Venezuela.

Evaluation on occluded hydrocarbon in deep–ultra deep ancient source rocks and its cracked gas resources

Directory of Open Access Journals (Sweden)

Jian Li

2015-12-01

Full Text Available Oil-cracked gas, as the main type of high-over mature marine natural gas in China, is mainly derived from occluded hydrocarbon. So it is significant to carry out quantitative study on occluded hydrocarbon. In this paper, the occluded hydrocarbon volume of the main basins in China was calculated depending on their types, abundances and evolution stages by means of the forward method (experimental simulation and the inversion method (geologic profile dissection. And then, occluded hydrocarbon evolution models were established for five types of source rocks (sapropelic, sapropelic prone hybrid, humic prone hybrid, humic and coal. It is shown that the hydrocarbon expulsion efficiency of sapropelic and sapropelic prone hybrid excellent source rocks is lower than 30% at the low-maturity stage, 30%–60% at the principal oil generation stage, and 50%–80% at the high-maturity stage, which are all about 10% higher than that of humic prone hybrid and humic source rocks at the corresponding stages. The resource distribution and cracked gas expulsion of occluded hydrocarbon since the high-maturity stage of marine source rocks in the Sichuan Basin were preliminarily calculated on the basis of the evolution models. The cracked gas expulsion is 230.4 × 1012 m3 at the high evolution stage of occluded hydrocarbon of the Lower Cambrian Qiongzhusi Fm in this basin, and 12.3 × 1012 m3 from the source rocks of Sinian Doushantuo Fm, indicating good potential for natural gas resources. It is indicated that the favorable areas of occluded hydrocarbon cracked gas in the Qiongzhusi Fm source rocks in the Sichuan Basin include Gaoshiti–Moxi, Ziyang and Weiyuan, covering a favorable area of 4.3 × 104 km2.

Will Venezuelan extra-heavy oil be a significant source of petroleum in the next decades?

International Nuclear Information System (INIS)

Sena, Marcelo Fonseca Monteiro de; Rosa, Luiz Pinguelli; Szklo, Alexandre

2013-01-01

Unconventional oil resources are needed to complement petroleum supply in the next decades. However, given the restrictions that pertain to the production of these resources, this article evaluates the availability of Venezuelan unconventional oil for helping meet the future worldwide petroleum demand. Venezuela has the world's second-largest oil reserves, but the majority of it is unconventional extra-heavy oil from the Orinoco Oil Belt. The perspective of Venezuelan production, the ways in which PDVSA, the state oil company, will raise funds for planned investments and the future oil price predictions are used to assess Venezuela's ability to serve as a source of unconventional oil in the coming years. Findings indicate that Venezuelan crude oil will be increasingly able to provide part of the marginal petroleum supply at a level predicted in global scenarios but short of that predicted by the country's government. Operational difficulties and the effort to raise financial resources for the oil production in the Belt require urgency in overcoming difficulties. As conventional production in Venezuela will stabilise in the coming years and the country is dependent on oil production, Venezuela will rely on extra-heavy oil extraction to ensure increased oil production and the stabilisation of internal accounts. - Highlights: • We analyse the future unconventional oil production capacity of Venezuela. • The study is based on operational capacity, investments capacity and future prices. • The study indicates a production shorter than that predicted by the Venezuelan government. • Venezuela can provide part of the marginal petroleum supply in the coming years

A comparison of geochemical features of extracts from coal-seams source rocks with different polarity solvents

Energy Technology Data Exchange (ETDEWEB)

Chen, Jianping; Deng, Chunping; Wang, Huitong

2009-02-15

There exists a great difference in group-type fractions and biomarker distributions of chloroform extracts from coals and coal-seams oils, which makes the source identification of coal-seams oils in sedimentary basins rather difficult. The experiment, in which four different polarity solvents, n-hexane, benzene, dichloromethane and chloroform, were used to extract 9 coal-seams source rocks and 3 typical lacustrine source rocks, showed that the yield of extracts increased gradually with increasing solvent polarity. The distribution features of their n-alkanes, isoprenoids and sterane and terpane biomarkers remained, in general, similar, showing no distinct enrichment or depletion for a certain fraction by any solvent. The compositional analysis on n-hexane and chloroform extracts showed that the absolute amount (concentration) of biomarkers was relatively low for the n-hexane extract but comparatively high for the chloroform extract, this difference became great among coal-seams source rocks but small among lacustrine mudstones. The statistical analysis on the relative amount of the 18 major biomarkers in n-hexane and chloroform extracts from 10 source rock samples showed that extracts with a proportional error for the same biomarker of less than 5% (including the analytical error) accounted for 84% while those with a proportional error over 10% amounted to below 5%. This suggested that the outcome of oil-source correlation made by these biomarkers will be independent of variations in amounts of saturates and biomarkers arising from solvent polarity. Therefore, biomarkers obtained from organic-rich source rocks including coals by the extraction with the commonly used chloroform solvent can be applied for the oilsource correlation of coal-seams petroliferous basins.

Mechanical Properties and Acoustic Emission Properties of Rocks with Different Transverse Scales

OpenAIRE

Yan, Xi; Jun, Li; Gonghui, Liu; Xueli, Guo

2017-01-01

Since the stability of engineering rock masses has important practical significance to projects like mining, tunneling, and petroleum engineering, it is necessary to study mechanical properties and stability prediction methods for rocks, cementing materials that are composed of minerals in all shapes and sizes. Rocks will generate acoustic emission during damage failure processes, which is deemed as an effective means of monitoring the stability of coal rocks. In the meantime, actual mining a...

Resource Assessment of the In-Place and Potentially Recoverable Deep Natural Gas Resource of the Onshore Interior Salt Basins, North Central and Northeastern Gulf of Mexico

Energy Technology Data Exchange (ETDEWEB)

Ernest A. Mancini; Donald A. Goddard

2005-04-15

The principal research effort for the first six months of Year 2 of the project has been petroleum system characterization. Understanding the burial and thermal maturation histories of the strata in the onshore interior salt basins of the North Central and Northeastern Gulf of Mexico areas is important in petroleum system characterization. The underburden and overburden rocks in these basins and subbasins are a product of their rift-related geohistory. Petroleum source rock analysis and thermal maturation and hydrocarbon expulsion modeling indicate that an effective regional petroleum source rock in the onshore interior salt basins, the North Louisiana Salt Basin, Mississippi Interior Salt Basin, Manila Subbasin and Conecuh Subbasin, was the Upper Jurassic Smackover lime mudstone. The Upper Cretaceous Tuscaloosa shale was an effective local petroleum source rock in the Mississippi Interior Salt Basin and a possible local source bed in the North Louisiana Salt Basin. Hydrocarbon generation and expulsion was initiated in the Early Cretaceous and continued into the Tertiary in the North Louisiana Salt Basin and the Mississippi Interior Salt Basin. Hydrocarbon generation and expulsion was initiated in the Late Cretaceous and continued into the Tertiary in the Manila Subbasin and Conecuh Subbasin. Reservoir rocks include Jurassic, Cretaceous and Tertiary siliciclastic and carbonate strata. Seal rocks include Jurassic, Cretaceous and Tertiary anhydrite and shale beds. Petroleum traps include structural and combination traps.

A Thermal Maturity Analysis of the Effective Cretaceous Petroleum System in the Southern Persian Gulf Basin

Directory of Open Access Journals (Sweden)

Majid Alipour

2017-10-01

Full Text Available Commercial hydrocarbon discoveries in the Cretaceous of the southern Persian Gulf basin provide direct evidence that there is an effective petroleum system associated with the Cretaceous series. The revised models of thermal maturity in this region are needed to investigate lateral and stratigraphic variations of thermal maturity, which have not so far been addressed in detail for this part of the Persian Gulf. Such thermal maturity models are required to delineate the existing play assessment risks and to predict properties in more deeply buried undrilled sections. This study uses two dimensional basin modeling techniques to reconstruct maturity evolution of the Cenomanian Middle Sarvak source rock, presumably the most likely source for these hydrocarbons. The results indicate that an estimated 900 meter difference in the depth of burial between the southeastern high and the adjacent trough tends to be translated into noticeable variations at both temperature (135 °C versus 162 °C and vitrinite reflectance (0.91% versus 1.35%. Since the organic matter in the mentioned source rock is of reactive type II, these could cause a shift of about 18 million years in the onset of hydrocarbon generation over respective areas.

Ideas: the column of: about the petroleum

International Nuclear Information System (INIS)

Sachs, J.D.

2004-01-01

Two energy problems will modify the economical and geopolitical future the next ten years: the petroleum supply insecurity from the Middle East and the climatic change. In this context the energy future depends on many solutions: the exploration and the development of new petroleum sources (without the Middle East), a better energy efficiency, the development of renewable energies sources and the use of fossil fuels respectful of the environment. (A.L.B.)

Bioremediation of petroleum-contaminated soil: A Review

Science.gov (United States)

Yuniati, M. D.

2018-02-01

Petroleum is the major source of energy for various industries and daily life. Releasing petroleum into the environment whether accidentally or due to human activities is a main cause of soil pollution. Soil contaminated with petroleum has a serious hazard to human health and causes environmental problems as well. Petroleum pollutants, mainly hydrocarbon, are classified as priority pollutants. The application of microorganisms or microbial processes to remove or degrade contaminants from soil is called bioremediation. This microbiological decontamination is claimed to be an efficient, economic and versatile alternative to physicochemical treatment. This article presents an overview about bioremediation of petroleum-contaminated soil. It also includes an explanation about the types of bioremediation technologies as well as the processes.

Metals distribution in Kumkol deposit petroleum

International Nuclear Information System (INIS)

Musaeva, Z.G.; Nadirov, A.N.; Ajdarbaev, A.S.

1997-01-01

Metals content in samples of Kumkol deposit petroleum is determined by the method of X-ray diffraction and neutron activation analysis. Specific consideration was devoted to nickel and vanadium. It is possible, that sources of these metals are various petroleum formation as well as both the absorbed or the got in stratum microelements. (author)

Requirements of radiation protection and physical protection for facilities of petroleum well logging

International Nuclear Information System (INIS)

Goessa, Eunícia João

2017-01-01

Petroleum is generated from the transformation of the organic matter accumulated in the sedimentary rocks, when submitted to the appropriate thermal conditions and is found both in the marine and terrestrial subsoil. In order to determine the volume of petroleum existing in a deposit oil wells technique is used which consists of a set of operations in which are recorded as a function of the depth, some characteristics of the geological layers along the well, such as permeability and porosity with the use of radioactive sources. The sources used in this practice belong to category 3, among five categories of categorization considered dangerous and in case of accident represents a higher level of radiological risk. The present work aims to present the main requirements of radiological safety and physical security to be applied in the licensing of an oil well profiling plant. In this work, the author supported the bibliographical review, which consisted in the collection of the essential literature related to the theme. The literature is composed of theoretical references published in books, theses, Brazilian norms, Mozambican laws, IAEA manuals and some published on the internet. The methodology used in this work was the bibliographical review with the objective of obtaining information on the formation of oil, oil well profiling concept, the radioactive sources used in this practice, for information on the main applicable radiological security and safety requirements radioactive sources and oil well profiling facilities. The inventory of radioactive sources, the use of shielding and the smear tests in radioactive sources are technical requirements that integrate the radiological safety and physical safety that must be followed by the licensees of the oil well profiling. (author). (author)

Petroleum systems and hydrocarbon accumulation models in the Santos Basin, SP, Brazil; Sistemas petroliferos e modelos de acumulacao de hidrocarbonetos na Bacia de Santos

Energy Technology Data Exchange (ETDEWEB)

Chang, Hung Kiang; Assine, Mario Luis; Correa, Fernando Santos; Tinen, Julio Setsuo [Universidade Estadual Paulista (UNESP), Rio Claro, SP (Brazil). Lab. de Estudos de Bacias]. E-mails: chang@rc.unesp.br; assine@rc.unesp.br; fscorrea@rc.unesp.br; jstinen@rc.unesp.br; Vidal, Alexandre Campane; Koike, Luzia [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Centro de Estudos de Petroleo]. E-mails: vidal@ige.unicamp.br; luzia@iqm.unicamp.br

2008-07-01

The Santos Basin was formed by rifting process during Mesozoic Afro-American separation. Sediment accumulation initiated with fluvial-lacustrine deposits, passing to evaporitic stage until reaching marginal basin stages. The analysis of hydrocarbon potential of Santos Basin identified two petroleum systems: Guaratiba-Guaruja and Itajai-Acu-Ilhabela. The Guaratiba Formation is less known in the Santos Basin because of small number of wells that have penetrated the rift section. By comparison with Campos Basin, hydrocarbons are of saline lacustrine origin deposited in Aptian age. Analogous to Campos Basin the major source rock is of saline-lacustrine origin, which has been confirmed from geochemical analyses of oil samples recovered from the various fields. These analyses also identified marine source rock contribution, indicating the Itajai-Acu source rock went through oil-window, particularly in structural lows generated by halokynesis. Models of hydrocarbon accumulation consider Guaratiba Formacao as the major source rock for shallow carbonate reservoirs of Guaruja Formacao and for late Albian to Miocene turbidites, as well as siliciclastic and carbonate reservoirs of the rift phase. Migration occurs along salt window and through carrier-beds. The seal rock is composed of shales and limestones intercalated with reservoir facies of the post-rift section and by thick evaporites overlying rift section, especially in the deeper water. In the shallow portion, shale inter-tongued with reservoir rocks is the main seal rock. The hydrocarbon generation and expulsion in the central-north portion of the basin is caused by overburden of a thick Senonian section. Traps can be structural (rollovers and turtle), stratigraphic (pinch-outs) and mixed origins (pinch-outs of turbidites against salt domes). (author)

Petroleum generation: 3D modeling of Cumuruxatiba Basin, Brazil; Modelagem 3D da geracao de petroleo na Bacia de Curumuxatiba, Brasil

Energy Technology Data Exchange (ETDEWEB)

Lemgruber, Adriana; Ferreira, Daniella A.; Goncalves, Felix T.T. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Lab. de Modelagem Multidisciplinar de Bacias Sedimentares (LAB2M); Vieira, Juliana R. [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

2008-07-01

In order to update and improve the knowledge of the tectonic-sedimentary evolution of Cumuruxatiba's petroleum systems, and also to call the attention of the petroleum companies, the National Agency of Oil, Gas and Biofuels (ANP) signed contract with COPPE / UFRJ for carrying out an extensive project of basin analysis. This paper presents the results of the integration geochemical data and three-dimensional maturation and petroleum generation modeling, on a regional scale. The results present an important progress in understanding the dynamic of the petroleum system in the area, and may be used as a basis for more consistent evaluation of the oil and gas potential and also of the exploitation risk at Cumuraxatiba basin. Three potential source rock intervals were simulated in the 3D model. Two intervals have been defined in the pre-salt zone, at the upper and basal portions of the rift section, and an interval at the post-salt section, at the top of Regencia formation/ basis of Urucutuca formation. The results point out that there is a significant oil and gas potential in deep-water regions and in the south portion of the continental shelf. (author)

La pyrolyse Rock-Eval et ses applications. Troisième partie. Rock-Eval Pyrolysis and Its Applications (Part Three

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

techniques du raffinage et de la récupération secondaire des bruts. The Rock-Eval pyrolysis method was designed to meet the needs of petroleum prospection and has now gained widespread use. It quickly provides different data on the organic content of rocks, such as the petroleum potential of series encountered, the nature of kerogens and their state of maturity. Two new versions of this equipment have been developed by Institut Français du Pétrole (IFP since the appearance of the first Rock-Eval devices in 1977. One is a Rock-Eval II that is completely automated thanks to its microprocessor and is also equipped with a module for determining the organic-carbon content. The other is a Rock-Eval III (Oil Show Analyzer which is different from the preceding one in that it makes a separate analysis of gas and oil as well as determining the organic-carbon content in place of peak S3. Concerning the interpretation of the method, experience gained both by applications to sedimentary basins and by experimental investigations in the laboratory has provided a better understanding of the parameters used (peaks S1, S2 and S3, pyrolysis temperature Tmax through their variations and, from this, better insight into the application limits of the method. Concerning the application of the method, the vertical representation of results in the form of geochemical logs leads to an interpretation that is both effective and practical. Reference charts and diagrams are used to characterize source rocks (petroleum potentials, types of organic matter, degree of evolution, weathering, etc. as well as migration phenomena. The compiling of geochemical maps on a basin-wide scale then becomes possible. Likewise, the method has left the field of petroleum prospection per se and found applications in the analyzing of coals, bituminous rocks, recent sediments and even techniques of the refining and secondary recovery of crude oils.

La pyrolyse Rock-Eval et ses applications. Première partie. Rock-Eval Pyrolysis and Its Applications (Part One

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

techniques du raffinage et de la récupération secondaire des bruts. The Rock-Eval pyrolysis method was designed to meet the needs of petroleum prospection and has now gained widespread use. It quickly provides different data on the organic content of rocks, such as the petroleum potential of series encountered, the nature of kerogens and their state of maturity. Two new versions of this equipment have been developed by Institut Français du Pétrole (IFP since the appearance of the first Rock-Eval devices in 1977. One is a Rock-Eval II that is completely automated thanks to its microprocessor and is also equipped with a module for determining the organic-carbon content. The other is a Rock-Eval III (Oil Show Analyzer which is different from the preceding one in that it makes a separate analysis of gas and oil as well as determining the organic-carbon content in place of peak S3. Concerning the interpretation of the method, experience gained both by applications to sedimentary basins and by experimental investigations in the laboratory has provided a better understanding of the parameters used (peaks S1, S2 and S3, pyrolysis temperature Tmax through their variations and, from this, better insight into the application limits of the method. Concerning the application of the method, the vertical representation of results in the form of geochemical logs leads to an interpretation that is both effective and practical. Reference charts and diagrams are used to characterize source rocks (petroleum potentials, types of organic matter, degree of evolution, weathering, etc. as well as migration phenomena. The compiling of geochemical maps on a basin-wide scale then becomes possible. Likewise, the method has left the field of petroleum prospection per se and found applications in the analyzing of coals, bituminous rocks, recent sediments and even techniques of the refining and secondary recovery of crude oils.

La pyrolyse Rock-Eval et ses applications. Deuxième partie. Rock-Eval Pyrolysis and Its Applications (Part Two

Directory of Open Access Journals (Sweden)

Espitalie J.

2006-11-01

techniques du raffinage et de la récupération secondaire des bruts. The Rock-Eval pyrolysis method was designed to meet the needs of petroleum prospection and has now gained widespread use. It quickly provides different data on the organic content of rocks, such as the petroleum potential of series encountered, the nature of kerogens and their state of maturity. Two new versions of this equipment have been developed by Institut Français du Pétrole (IFP since the appearance of the first Rock-Eval devices in 1977. One is a Rock-Eval II that is completely automated thanks to its microprocessor and is also equipped with a module for determining the organic-carbon content. The other is a Rock-Eval III (Oil Show Analyzer which is different from the preceding one in that it makes a separate analysis of gas and oil as well as determining the organic-carbon content in place of peak S3. Concerning the interpretation of the method, experience gained both by applications to sedimentary basins and by experimental investigations in the laboratory has provided a better understanding of the parameters used (peaks S1, S2 and S3, pyrolysis temperature Tmax through their variations and, from this, better insight into the application limits of the method. Concerning the application of the method, the vertical representation of results in the form of geochemical logs leads to an interpretation that is both effective and practical. Reference charts and diagrams are used to characterize source rocks (petroleum potentials, types of organic matter, degree of evolution, weathering, etc. as well as migration phenomena. The compiling of geochemical maps on a basin-wide scale then becomes possible. Likewise, the method has left the field of petroleum prospection per se and found applications in the analyzing of coals, bituminous rocks, recent sediments and even techniques of the refining and secondary recovery of crude oils.

Removal of light petroleum hydrocarbons from water sources using polypropylene and titanium dioxide nano-composite

Directory of Open Access Journals (Sweden)

H. Karyab

2016-08-01

Full Text Available Background: Petroleum hydrocarbons are the most important pollutants which threat human health and aquatics. Adsorbents are one of the common equipment in water pollution management; however, their applications have been associated with limitations. Objective: To evaluate the potential of polypropylene/titanium dioxide Nano-composite in adsorption of light petroleum hydrocarbons from water sources. Methods: This experimental study was conducted at school of health, Qazvin University of Medical Sciences in 2014-15. Activation of polypropylene fibers, with 1 cm length and 300 microns diameters, was achieved with wet heating. To synthesize of nano-composite the fibers were coated with nano-titanium dioxide with 20 nm diameter. The sonication was performed at 26 kHz and 100 W of power in 40ºc. The morphology of the fractured surfaces of impact specimens was examined by FESEM. The adsorption rate of petrol and gasoline, as surrogate of TPH, was evaluated in different retention time within polyamide mesh aperture diameter of 250 nm. Average of TPH adsorbing, per unit weight of adsorbent, were analyzed with analysis of variance and Scheffe post hoc tests. Findings: The FESEM micrographs showed that the dispersion of the nano-Tio2 particles was relatively good and only few aggregations exist. The maximum adsorption capacity of petrol and gasoline was obtained in 30 minute. The adsorption rate of gasoline was 6.49±0.10 g/g and oil was 7.01±0.13 g/g. Conclusion: According to the results and in comparison with commercial imported adsorbents, the synthesized Nano-composite had favorable performance. The results show that the polypropylene/Tio2 Nano-composite can be used effectively in light petroleum hydrocarbons removal from polluted water sources.

Oil companies' customer records as a source of petroleum statistics; Oljeselskapenes kunderegistre som kilde i petroleumsstatistikken

Energy Technology Data Exchange (ETDEWEB)

Isaksen, Elisabeth Thuestad; Hoeie, Henning; Flugsrud, Ketil

2012-10-15

Detailed sales data from oil companies' customer records are considered a better source of data for the sales statistics for petroleum products than today's more aggregated source basis. Using detailed data from sales transactions allow for a safer, more detailed and more consistent industry classification and geographic distribution of sales than what is possible with current practice. Particularly for sale to transport and the public sector will the detailed data could make a more proper distribution of sales.(eb)

Source Test Report for the 205 Delayed Coking Unit Drum 205-1201 and Drum 205-1202 Depressurization Vents (Marathon Petroleum Company LLC)

Science.gov (United States)

The 2010 Source Test was performed during the atmospheric depressurization step of the delayed coking process prior to the removal of petroleum coke from the coke drum. The 205 DCU was operated under a variety of conditions during the 2010 Source Test.

Bioremediation of petroleum contaminated soil

International Nuclear Information System (INIS)

Autry, A.R.; Ellis, G.M.

1992-01-01

This paper reports on bioremediation, which offers a cost-competitive, effective remediation alternative for soil contaminated with petroleum products. These technologies involve using microorganisms to biologically degrade organic constituents in contaminated soil. All bioremediation applications must mitigate various environmental rate limiting factors so that the biodegradation rates for petroleum hydrocarbons are optimized in field-relevant situations. Traditional bioremediation applications include landfarming, bioreactors, and composting. A more recent bioremediation application that has proven successful involves excavation of contaminated soil. The process involves the placement of the soils into a powerscreen, where it is screened to remove rocks and larger debris. The screened soil is then conveyed to a ribbon blender, where it is mixed in batch with nutrient solution containing nitrogen, phosphorus, water, and surfactants. Each mixed soil batch is then placed in a curing pile, where it remains undisturbed for the remainder of the treatment process, during which time biodegradation by naturally occurring microorganisms, utilizing biochemical pathways mediated by enzymes, will occur

Effects of Host-rock Fracturing on Elastic-deformation Source Models of Volcano Deflation.

Science.gov (United States)

Holohan, Eoghan P; Sudhaus, Henriette; Walter, Thomas R; Schöpfer, Martin P J; Walsh, John J

2017-09-08

Volcanoes commonly inflate or deflate during episodes of unrest or eruption. Continuum mechanics models that assume linear elastic deformation of the Earth's crust are routinely used to invert the observed ground motions. The source(s) of deformation in such models are generally interpreted in terms of magma bodies or pathways, and thus form a basis for hazard assessment and mitigation. Using discontinuum mechanics models, we show how host-rock fracturing (i.e. non-elastic deformation) during drainage of a magma body can progressively change the shape and depth of an elastic-deformation source. We argue that this effect explains the marked spatio-temporal changes in source model attributes inferred for the March-April 2007 eruption of Piton de la Fournaise volcano, La Reunion. We find that pronounced deflation-related host-rock fracturing can: (1) yield inclined source model geometries for a horizontal magma body; (2) cause significant upward migration of an elastic-deformation source, leading to underestimation of the true magma body depth and potentially to a misinterpretation of ascending magma; and (3) at least partly explain underestimation by elastic-deformation sources of changes in sub-surface magma volume.

Madbi Amran/Qishn total petroleum system of the Ma'Rib-Al Jawf/Shabwah, and Masila-Jeza basins, Yemen

Science.gov (United States)

Ahlbrandt, Thomas S.

2002-01-01

Since the first discovery of petroleum in Yemen in 1984, several recent advances have been made in the understanding of that countrys geologic history and petroleum systems. The total petroleum resource endowment for the combined petroleum provinces within Yemen, as estimated in the recent U.S. Geological Survey world assessment, ranks 51st in the world, exclusive of the United States, at 9.8 BBOE, which includes cumulative production and remaining reserves, as well as a mean estimate of undiscovered resources. Such undiscovered petroleum resources are about 2.7 billion barrels of oil, 17 trillion cubic feet (2.8 billion barrels of oil equivalent) of natural gas and 1 billion barrels of natural gas liquids. A single total petroleum system, the Jurassic Madbi Amran/Qishn, dominates petroleum generation and production; it was formed in response to a Late Jurassic rifting event related to the separation of the Arabian Peninsula from the Gondwana supercontinent. This rifting resulted in the development of two petroleum-bearing sedimentary basins: (1) the western MaRibAl Jawf / Shabwah basin, and (2) the eastern Masila-Jeza basin. In both basins, petroleum source rocks of the Jurassic (Kimmeridgian) Madbi Formation generated hydrocarbons during Late Cretaceous time that migrated, mostly vertically, into Jurassic and Cretaceous reservoirs. In the western MaRibAl Jawf / Shabwah basin, the petroleum system is largely confined to syn-rift deposits, with reservoirs ranging from deep-water turbidites to continental clastics buried beneath a thick Upper Jurassic (Tithonian) salt. The salt initially deformed in Early Cretaceous time, and continued halokinesis resulted in salt diapirism and associated salt withdrawal during extension. The eastern Masila-Jeza basin contained similar early syn-rift deposits but received less clastic sediment during the Jurassic; however, no salt formed because the basin remained open to ocean circulation in the Late Jurassic. Thus, Madbi Formation-sourced

Petroleum supply monthly, March 1994

Energy Technology Data Exchange (ETDEWEB)

1994-03-30

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

Petroleum Market Model of the National Energy Modeling System. Part 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-18

The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions, the production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level.

Analysis of petroleum company investments in nonpetroleum energy sources. Book I

Energy Technology Data Exchange (ETDEWEB)

Ryan, P. Jr.; Ryan, T.C.

1979-12-12

The purpose of this report is to analyze the investment strategies of US oil companies and the depth of their present and future investments in nonpetroleum energy sources. For purposes of this study, the nonpetroleum energy sources to be discussed are coal, uranium/nuclear, synthetics from coal, oil shale, geothermal, and solar. To gather necessary subjective data, the authors interviewed the managements of more than forty companies, the majority of which are directly involved in the production of various forms of energy. Others are substantial energy users. Interviews were also held with various federal and state regulatory agencies, with federal legislative groups, and with representatives of industry associations. These interviews were not intended to be a survey; their purpose was rather to explore the perceptions of petroleum company managements concerning nonpetroleum energy sources and the reasons for their company's participation, or lack of participation, in the development of these resources. Quantitative data came from reports prepared by federal investigative and regulatory agencies, from testimony given before investigative and regulatory bodies, from public company reports (annual reports, quarterly reports, 10-K's, 8-K's, registration statements, press releases, etc.), from industry, research and investment organizations, from universities, and from a variety of publications.

Energy and public health: the challenge of peak petroleum.

Science.gov (United States)

Frumkin, Howard; Hess, Jeremy; Vindigni, Stephen

2009-01-01

Petroleum is a unique and essential energy source, used as the principal fuel for transportation, in producing many chemicals, and for numerous other purposes. Global petroleum production is expected to reach a maximum in the near future and to decline thereafter, a phenomenon known as "peak petroleum." This article reviews petroleum geology and uses, describes the phenomenon of peak petroleum, and reviews the scientific literature on the timing of this transition. It then discusses how peak petroleum may affect public health and health care, by reference to four areas: medical supplies and equipment, transportation, energy generation, and food production. Finally, it suggests strategies for anticipating and preparing for peak petroleum, both general public health preparedness strategies and actions specific to the four expected health system impacts.

Taking the petroleum out of petrochemistry

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, T

1982-01-01

It is thought to be inevitable that world production of petroleum will start declining in the not too distant future. When this happens, the only feedstock for the organic chemicals industry and the polymer chemistry industry will be coal. It is emphasized that the best way of substituting coal for petroleum fractions as an alternative energy source is the technologically easy conversion of economic coal to methanol. There are explanations of the problems involved in obtaining fuel methanol as an energy source, as feedstock for the chemical industry, and as a raw material for chemistry. (13 refs.)

Modelling the petroleum generation and migration of the third member of the Shahejie Formation (Es3) in the Banqiao Depression of Bohai Bay Basin, Eastern China

Science.gov (United States)

Guo, Xiaowen; He, Sheng; Liu, Keyu; Shi, Zhongsheng; Bachir, Sani

2011-01-01

The mudstones in the third member of the Shahejie Formation (Es3) are the primary source rocks in the Banqiao Depression of Bohai Bay Basin. They are rich in organic matter with Total Organic Carbon (TOC) content up to 3.5%. The sandstones in the Es3 member are the deepest proven hydrocarbon reservoir rocks with measured porosity and permeability values ranging from 3.6% to 32.4% and from 0.01 md to 3283.7 md, respectively. One, two and three-dimensional basin modelling studies were performed to analyse the petroleum generation and migration history of the Es3 member in the Banqiao Depression based on the reconstruction of the burial, thermal and maturity history in order to evaluate the remaining potential of this petroleum province. The modelling results are calibrated with measured vitrinite reflectance ( R o), borehole temperatures and some drilling results of 63 wells in the study area. Calibration of the model with thermal maturity and borehole temperature data indicates that the present-day heat flow in the Banqiao Depression varies from 59.8 mW/m 2 to 61.7 mW/m 2 and the paleo-heat flow increased from 65 Ma to 50.4 Ma, reached a peak heat-flow values of approximately 75 mW/m 2 at 50.4 Ma and then decreased exponentially from 50.4 Ma to present-day. The source rocks of the Es3 member are presently in a stage of oil and condensate generation with maturity from 0.5% to 1.8% R o and had maturity from 0.5% to 1.25% R o at the end of the Dongying Formation (Ed) deposition (26 Ma). Oil generation (0.5% R o) in the Es3 member began from about 37 Ma to 34 Ma and the peak hydrocarbon generation (1.0% R o) occurred approximately from 30 Ma to 15 Ma. The modelled hydrocarbon expulsion evolution suggested that the timing of hydrocarbon expulsion from the Es3 member source rocks began from 31 Ma to 10 Ma with the peak hydrocarbon expulsion shortly after 26 Ma. Secondary petroleum migration pathways in the Es3 member of the Banqiao Depression are modelled based on the

A computer-assisted rock type data catalogue for gas formations; Ein rechnergestuetzter Gesteinsdatenkatalog fuer Gasformationen

Energy Technology Data Exchange (ETDEWEB)

Reitenbach, V.; Pusch, G.; Moeller, M.; Koll, S. [TU Clausthal (Germany). Inst. fuer Erdoel- und Erdgastechnik; Constantini, A.; Junker, A.; Anton, H. [RWE Dea AG, Hamburg (Germany)

2007-09-13

Modern reservoir management commonly requires versatile reservoir data which are neces-sary for integrated reservoir characterization, evaluation and development planning. The rock data necessary for numerical reservoir simulation studies often have to be collected from different sources, analysed and sorted with a considerable effort. In a framework of DGMK research program (DGMK project 593-9/4), the Institute of Petro-leum Engineering (Clausthal University of Technology) and RWE DEA AG have developed a new tool named Rock Data Catalogue, which is capable of managing large amounts of rock data more efficiently and deriving new specific correlations for European rock types. The use of Rock Data Catalogue can facilitate the essential input data generation and proc-essing procedure for reservoir simulation studies. The Rock Data Catalogue is comprised of a Data Base Module of digitalized reservoir rock data and an interactive Data Correlation Module. Both modules are built-up as an interface to common reservoir simulation software. The universal structure of the software also makes it possible to exchange the data with other rock data information systems. The Data Correlation Module implements a ''Decision-Structure'' module, which helps the reservoir engineer to select the rock data for analysis and correlation depending on its litho-facial type and permeability class. The Data Base Module enables a quick search of appro-priated data sets and their export into the correlation module. The open source data of the North German Rotliegend gas formations as well as the data of measurements on Rotliegend core samples performed at the ITE in course of the DGMK tight gas projects were implemented in the rock data base. Correlations of poro/perm data, two-phase flow and capillary pressure functions of the Rotliegend sandstones with the per-meability range between 20 and 0.01 mD are implemented in the rock data base and serve for quality checking of the

Qualitative and quantitative analysis of Dibenzofuran, Alkyldibenzofurans, and Benzo[b]naphthofurans in crude oils and source rock extracts

Science.gov (United States)

Meijun Li,; Ellis, Geoffrey S.

2015-01-01

Dibenzofuran (DBF), its alkylated homologues, and benzo[b]naphthofurans (BNFs) are common oxygen-heterocyclic aromatic compounds in crude oils and source rock extracts. A series of positional isomers of alkyldibenzofuran and benzo[b]naphthofuran were identified in mass chromatograms by comparison with internal standards and standard retention indices. The response factors of dibenzofuran in relation to internal standards were obtained by gas chromatography-mass spectrometry analyses of a set of mixed solutions with different concentration ratios. Perdeuterated dibenzofuran and dibenzothiophene are optimal internal standards for quantitative analyses of furan compounds in crude oils and source rock extracts. The average concentration of the total DBFs in oils derived from siliciclastic lacustrine rock extracts from the Beibuwan Basin, South China Sea, was 518 μg/g, which is about 5 times that observed in the oils from carbonate source rocks in the Tarim Basin, Northwest China. The BNFs occur ubiquitously in source rock extracts and related oils of various origins. The results of this work suggest that the relative abundance of benzo[b]naphthofuran isomers, that is, the benzo[b]naphtho[2,1-d]furan/{benzo[b]naphtho[2,1-d]furan + benzo[b]naphtho[1,2-d]furan} ratio, may be a potential molecular geochemical parameter to indicate oil migration pathways and distances.

A review of the petroleum geochemistry of the Precaspian Basin

Energy Technology Data Exchange (ETDEWEB)

Pairazian, V.V. [All-Russian Geological Oil Research and Prospecting Inst. (VNIGNI), Moscow (Russian Federation); ENI-AGIP, San Donato Milanese (Italy)

1999-11-01

On the territory of the former Soviet Union more than 30- oil and gas-bearing basins have been defined. Among them the Precaspian basin is one of the most prolific in terms of oil and gas exploration and production. The basin is situated in the southeastern part of the East European Platform and covers an areas of about 500 000 km{sup 2}. There are a number of source rocks of different ages, among which the principal ones are Lower Permian, Middle Carboniferous and Middle Devonian marine shales and carbonates. The post-salt Mesozoic sources are of less significance. Geological and geochemical data interpretation allows the main oil/gas accumulation zones and new exploration prospects to be defined. Two main petroleum systems are recognised in the Palaeozoic sequence of the basin, containing 90% of the recoverable hydrocarbon resources: Lower Permian-Middle Carboniferous and Lower Carboniferous-Upper Devonian. The new exploration targets are deep Middle Devonian clastic reservoirs on the passive continental margins and Middle Carboniferous (Bashkirian) carbonates in the Caspian offshore part of the basin. (Author)

Shale characterization in mass transport complex as a potential source rock: An example from onshore West Java Basin, Indonesia

Science.gov (United States)

Nugraha, A. M. S.; Widiarti, R.; Kusumah, E. P.

2017-12-01

This study describes a deep-water slump facies shale of the Early Miocene Jatiluhur/Cibulakan Formation to understand its potential as a source rock in an active tectonic region, the onshore West Java. The formation is equivalent with the Gumai Formation, which has been well-known as another prolific source rock besides the Oligocene Talang Akar Formation in North West Java Basin, Indonesia. The equivalent shale formation is expected to have same potential source rock towards the onshore of Central Java. The shale samples were taken onshore, 150 km away from the basin. The shale must be rich of organic matter, have good quality of kerogen, and thermally matured to be categorized as a potential source rock. Investigations from petrography, X-Ray diffractions (XRD), and backscattered electron show heterogeneous mineralogy in the shales. The mineralogy consists of clay minerals, minor quartz, muscovite, calcite, chlorite, clinopyroxene, and other weathered minerals. This composition makes the shale more brittle. Scanning Electron Microscope (SEM) analysis indicate secondary porosities and microstructures. Total Organic Carbon (TOC) shows 0.8-1.1 wt%, compared to the basinal shale 1.5-8 wt%. The shale properties from this outcropped formation indicate a good potential source rock that can be found in the subsurface area with better quality and maturity.

Petroleum supply annual 1998: Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1998 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. This second volume contains final statistics for each month of 1998, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

Petroleum supply annual, 1997. Volume 2

International Nuclear Information System (INIS)

1998-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs

Petroleum supply annual 1996: Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The second volume contains final statistics for each month of 1996, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

Petroleum supply annual, 1997. Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs.

Petroleum supply annual 1994, Volume 2

International Nuclear Information System (INIS)

1995-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary

Petroleum supply annual 1996: Volume 2

International Nuclear Information System (INIS)

1997-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1996 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Capacity; each with final annual data. The second volume contains final statistics for each month of 1996, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs

Petroleum supply annual 1995: Volume 2

International Nuclear Information System (INIS)

1996-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1995 through monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and selected Refinery Statistics each with final annual data. The second volume contains final statistics for each month of 1995, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary

Petroleum supply annual 1998. Volume 2

International Nuclear Information System (INIS)

1999-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1998 through monthly surveys. The PSA is divided into two volumes. The first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. This second volume contains final statistics for each month of 1998, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary. 35 tabs

Radiation Emergency Planning in Petroleum Industry

International Nuclear Information System (INIS)

El-Shinawy, R.M.K.; El-Naggar, M.A.; Abdel-Fattah, A.T.; Gomaa, A.M.

2001-01-01

Similar to all industrial activities utilizing radiation sources, or dealing with radioactive materials in its operations, petroleum industry requires the organization of a Radiation Emergency Plan. This plan should be based on a comprehensive and subtle understanding of the extensive multidisciplinary operations involved in petroleum processing and the dangers that threaten human health, environment and property; both from ordinary emergency situations common to petroleum industry activities and also from radiation emergency events. Radiation emergencies include radiological source accidents involving occurrence of high dose exposures. Radioactive contamination or spill are also major problems that may cause low dose exposures and environmental radioactive contamination. The simultaneous occurrence of other industrial emergency events such as fires or structural collapses will add to the seriousness of the emergency situation. The essential aspects of Radiation Emergency Planning include notification, assessment of situation, foresight, definition of roles and responsibilities including health safety and environmental concepts. An important contribution to the Emergency Planning is the proper intelligent medical response. Another essential parameter is the training of personnel that will undertake the responsibility of executing the emergency procedures according to the various emergency situations. The main features of the radiation Emergency Plan in Petroleum industry is presented in the text

Petroleum Market Model of the National Energy Modeling System

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions. The production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level. This report is organized as follows: Chapter 2, Model Purpose; Chapter 3, Model Overview and Rationale; Chapter 4, Model Structure; Appendix A, Inventory of Input Data, Parameter Estimates, and Model Outputs; Appendix B, Detailed Mathematical Description of the Model; Appendix C, Bibliography; Appendix D, Model Abstract; Appendix E, Data Quality; Appendix F, Estimation methodologies; Appendix G, Matrix Generator documentation; Appendix H, Historical Data Processing; and Appendix I, Biofuels Supply Submodule.

Petroleum Market Model of the National Energy Modeling System

International Nuclear Information System (INIS)

1997-01-01

The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions. The production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level. This report is organized as follows: Chapter 2, Model Purpose; Chapter 3, Model Overview and Rationale; Chapter 4, Model Structure; Appendix A, Inventory of Input Data, Parameter Estimates, and Model Outputs; Appendix B, Detailed Mathematical Description of the Model; Appendix C, Bibliography; Appendix D, Model Abstract; Appendix E, Data Quality; Appendix F, Estimation methodologies; Appendix G, Matrix Generator documentation; Appendix H, Historical Data Processing; and Appendix I, Biofuels Supply Submodule

Analysis of petroleum oily sludge producing in petroleum field of Rio Grande do Norte, Brazil

Energy Technology Data Exchange (ETDEWEB)

Lima, Cicero de Souza; Lima, Regineide Oliveira; Silva, Edjane Fabiula Buriti da; Castro, Kesia Kelly Vieira de; Chiavone Filho, Osvaldo; Araujo, Antonio Souza de [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil)

2012-07-01

In exploration and production of petroleum is generated solid waste different and components other. The petroleum oily sludge is a complex mix of components different (water, oil and solid). The petroleum oily sludge generally has other residues and is formed during production and operations, transport, storage and petroleum refining (atmospheric residue, vacuum residue and catalytic cracking residue). However, according to its origin, the compositions can be found quite varied for sludge. Observing the process steps production and refining is possible to locate its main sources and percentage contributions in terms of waste generation. The elemental analysis was performed with oily sludge from region and it showed different composition. For carbon element and hydrogen, small differences was observed, but for was observed greater differences for Oxygen element. The sludge has different inorganic and organic composition. The sludge from oil water separator (OWS) 2 showed a greater amount of oil (94.88%), this may indicate a residue of aggregate high for petroleum industry. In analysis of Saturates, Aromatics, Resins and Asphaltenes (SARA), the sludge from unloading showed amount high of saturates. The inorganic material separated from sludge was characterized and sludge from OWS 2 had high amount sulfur (41.57%). The sludge analyzed showed organic components high values, so it can be treated and reprocessed in process units petroleum industry. The analysis thermal degradation had a better setting for treated oily sludge. (author)

Industry sector analysis, Mexico: Annual petroleum report. Export Trade Information

International Nuclear Information System (INIS)

1992-01-01

The comprehensive appraisal of the Mexican Petroleum industry was completed in July 1991. Some of the topics concerning the Mexican petroleum industry covered in the Annual Petroleum Report include: exploration efforts, oil reserves, pipelines, refining, finances, transportation, alternative energy sources, and others. The report also contains lists of petrochemicals produced in Mexico and extensive statistics on oil production and export prices

Characterization of norm sources in petroleum coke calcining processes - 16314

International Nuclear Information System (INIS)

Hamilton, Ian S.; Halter, Donald A.; Fruchtnicht, Erich H.; Arno, Matthew G.; Haumann, Donald F

2009-01-01

Petroleum coke, or 'petcoke', is a waste by-product of the oil refining industry. The majority of petcoke consumption is in energy applications; catalyst coke is used as refinery fuel, anode coke for electricity conduction, and marketable coke for heating cement kilns. Roskill has predicted that long-term growth in petroleum coke production will be maintained, and may continue to increase slightly through 2012. Petcoke must first be calcined to drive off any undesirable petroleum by-products that would shorten the coke product life cycle. As an example, the calcining process can take place in large, rotary kilns heated to maximum temperatures as high as approximately 1400-1540 deg. C. The kilns and combustion/settling chambers, as well as some cooler units, are insulated with refractory bricks and other, interstitial materials, e.g., castable refractory materials, to improve the efficiency of the calcining process. The bricks are typically made of 70-85-percent bauxite, and are slowly worn away by the calcining process; bricks used to line the combustion chambers wear away, as well, but at a slower rate. It has been recognized that the refractory materials contain slight amounts of naturally occurring radioactive materials (NORM) from the uranium- and thorium-decay series. Similarly, low levels of NORM could be present in the petcoke feed stock given the nature of its origin. Neither the petcoke nor the refractory bricks represent appreciable sources of radiation or radioactive waste. However, some of the demolished bricks that have been removed from service because of the aforementioned wearing process have caused portal alarms to activate at municipal disposal facilities. This has lead to the current investigation into whether there is a NORM concentrating mechanism facilitated by the presence of the slightly radioactive feed stock in the presence of the slightly radioactive refractory materials, at calcining-zone temperatures. Research conducted to date has been

The History of Petroleum Pollution in Malaysia; Urgent Need for Integrated Prevention Approach

OpenAIRE

Mahyar Sakari

2010-01-01

Petroleum pollution is known as point and non-point source of contaminations in the environment. A major class of petroleum contaminant is groups of compounds consist of two or more fused benzene rings called polycyclic aromatic hydrocarbons (PAHs) that are carcinogenic, mutagenic and toxic. Source identification of petroleum pollution is necessary to prevent pollution entry into the environment. Eight sedimentary cores were obtained from developed and developing areas around Peninsular Malay...

The Future of Petroleum As an Energy Resource L'avenir du pétrole comme source d'énergie

Directory of Open Access Journals (Sweden)

Erdman J. G.

2006-10-01

Full Text Available Civilization is based on man's capacity to generate more energy than is necessary to provide for subsistence. The industrial revolution became possible through the developpement of abundant energy based mainly on the production and utilization of fossil fuels. As non-renewable energy resources are exploited, the energy required Io produce and utilize these fuels trends upward. Ultimately for each resource the trade-off point is reached, that is where the energy return no longer exceeds the energy for production and utilization. ln compensation for particularly desirable properties a slightly negative balance may be acceptable provided there is compention by a somewhat less desirable energy source. In this century, petroleum has become a highly favored energy source. Today in the United States 75% of the energy consumed is derived from petroleum. The recent rapid rise in the world price of petroleum is, for the most part, the consequence of political and economic factors. Such factors may well force a trend to altern energy sources in some consumer countries. On a world basis, the future use of petroleum both in time and in extent of depletion of reserves will depend upon the capability of petroleum technologists to slow the closing of the gap between energy outlay and return. To perpetuate past successes, new philosophies and technologies exploration, production and utilization must be developed. La civilisation est basée sur la capacité humaine de créer plus d'énergie qu'il est nécessaire d'en fournir pour subsister. La révolution industrielle a été possible grâce ou développement d'énergie abondante basée principalement sur la production et l'utilisation des combustibles fossiles. Au fur et à mesure que l'on exploite les sources non renouvelables d'énergie, on constate une augmentation de la quantité d'énergie requise pour les produire et les utiliser. A la fin pour chaque matière première, le point limite est atteint lorsque

Old and new versions of the alpha radiation theory of petroleum origin

International Nuclear Information System (INIS)

Paschoa, A.S.

1981-03-01

Some aspects of petroleum formation and the world distribution of fossil fuels deposits were recent clarified. However, the source of energy associated with petroleum genesis is still largely debatable. Evidence accumulated over the years allows to demonstrate the energetic feasibility of a modern version of the old alpha radiation theory of petroleum origin. This theory is reviewed and examined critically under new light to be reformulated by taking advantage of relevant interdisciplinary data mostly not available when the old alpha radiation theory was suggested, developed and then discredited. The geological ages accepted for the formation of most of the known petroleum reserves are within a range that makes long-lived natural alpha emitters a feasible energy source for at least part of the energy necessary for the formation of petroleum hydrocarbon. (author) [pt

Source rock identification of sediments using trace element ratios and 13C isotope data - a case study from Pondicherry region

International Nuclear Information System (INIS)

Tirumalesh, K.; Kulkarni, U.P.; Singh, Gursharan; Ramakumar, K.L.; Chidambaram, S.

2012-01-01

Compositional characteristics of source rocks are generally well recorded in sedimentary deposits and provide valuable information about nature of source rocks even though weathering, physical sorting and deposition environment influence the sediment geochemistry. In this paper we report major, trace element and 13 C isotope data of cutting samples collected from Quaternary, Tertiary and Cretaceous formations in Pondicherry area. The distribution patterns and inter elemental correlations are used to identify source rock composition and carbon isotope compositions to understand the sediment deposition conditions. Mineralogy of the bulk sediment indicates presence of Quartz, K-feldspar, Calcite, Mg-calcite, Aragonite and Clay minerals. Compared to upper continental crust values most of these sediments show lower concentration of all elements except Ca and Zn at some depths. The depletion is probably associated with weathering of feldspar and removal of elements through solution. This also increases the proportion of quartz relative to source rock. The ratios of redox sensitive elements (Th/U) infer oxic weathering in shallow sediments. Elemental ratios (La/Sc, Th/Sc, Th/Cr, Th/Co) and ternary plots (La-Th-Sc and Th-Hf-Co) indicate contribution of felsic source rocks with varying degree of weathering. These plots also infer the inherent heterogeneity in the source rocks. Hafnium correlations with other trace elements suggest contribution of Tonalitic rocks in addition to granite to these sediments. The geochemical characteristics of the sediments are found to be similar to that of sediments belonging to similar geology in nearby regions. Presence of shallow marine condition during the sedimentation is inferred from the detrital index (DI) values, which is further supported by the presence of fibrous clay minerals in ESEM scans. This study also brings out the utility of δ 13 C information to reinforce the geochemical and mineralogical inferences. (author)

Characteristics of the Triassic Source Rocks of the Aitutu Formation in the (West Timor Basin

Directory of Open Access Journals (Sweden)

Asep Kurnia Permana

2014-12-01

Full Text Available DOI:10.17014/ijog.v1i3.192The Triassic rocks of the (West Timor Basin have been identified that was mainly deposited in the  marine environment. The fine grained clastics and carbonate  rocks of this Triassic marine  facies are considered to be the most promising source rocks potential in this basin. In this paper we present geochemical and petrographic data from outcrop samples of the Triassic carbonate Aitutu Formation, due to emphasized the organic maturation, kerogen type of the organic matter and the origin of the organic matter.  A representative of selected sample were subjected to the Rock-Eval Pyrolisis, vitrinite reflectance and thermal alteration index, bitumen extraction, were analyzed on the GC-MS. The samples were collected from marine deposit of the Triassic Sequence. The TOC values of the analyzed sample range between rich and rich organic richness (0.51% - 9.16%, wt.%, TOC, which consists mainly of type II and III kerogen and the organic matter consider to be predominantly oil/gas prone and gas prone potential. The thermal maturity assessed from Tmax, TAI, and vitrinite reflectance shows an immature to early peak mature stage of the organic matter. The GC-MS analyses of the biomarkers indicate mainly the organic matter derived from mixed source rocks facies containing alga debris and higher plant terrestrial origin.

Appalachian basin oil and natural gas: stratigraphic framework, total petroleum systems, and estimated ultimate recovery: Chapter C.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ryder, Robert T.; Milici, Robert C.; Swezey, Christopher S.; Trippi, Michael H.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The most recent U.S. Geological Survey (USGS) assessment of undiscovered oil and gas resources of the Appalachian basin was completed in 2002 (Milici and others, 2003). This assessment was based on the total petroleum system (TPS), a concept introduced by Magoon and Dow (1994) and developed during subsequent studies such as those by the U.S. Geological Survey World Energy Assessment Team (2000) and by Biteau and others (2003a,b). Each TPS is based on specific geologic elements that include source rocks, traps and seals, reservoir rocks, and the generation and migration of hydrocarbons. This chapter identifies the TPSs defined in the 2002 Appalachian basin oil and gas assessment and places them in the context of the stratigraphic framework associated with regional geologic cross sections D–D′ (Ryder and others, 2009, which was re-released in this volume, chap. E.4.1) and E–E′ (Ryder and others, 2008, which was re-released in this volume, chap. E.4.2). Furthermore, the chapter presents a recent estimate of the ultimate recoverable oil and natural gas in the basin.

EIA model documentation: Petroleum market model of the national energy modeling system

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-28

The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. Documentation of the model is in accordance with EIA`s legal obligation to provide adequate documentation in support of its models. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions, the production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level.

EIA model documentation: Petroleum market model of the national energy modeling system

International Nuclear Information System (INIS)

1995-01-01

The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. Documentation of the model is in accordance with EIA's legal obligation to provide adequate documentation in support of its models. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions, the production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level

Evaluating the utility of hydrocarbons for Re-Os geochronology : establishing the timing of processes in petroleum ore systems

Energy Technology Data Exchange (ETDEWEB)

Selby, D.; Creaser, R.A. [Alberta Univ., Edmonton, AB (Canada). Dept. of Earth and Atmospheric Sciences

2005-07-01

Oil from 6 Alberta oil sands deposits were analyzed with a rhenium-osmium (Re-Os) isotope chronometer, an emerging tool for determining valuable age information on the timing of petroleum generation and migration. The tool uses molybdenite and other sulphide minerals to establish the timing and duration of mineralization. However, establishing the timing events of petroleum systems can be problematic because viable sulphides for the Re-Os chronometer are often not available. Therefore, the known presence of Re and Os associated with organic matter in black shale, a common source of hydrocarbons, may suggest that bitumen and petroleum common to petroleum systems may be utilised for Re-Os geochronology. This study evaluated the potential of the Re-Os isotopic system for geochronology and as an isotopic tracer for hydrocarbon systems. The evaluation was based on Re-Os isotopic analyses of bitumen and oil sands. Hydrocarbons formed from migrated oil in both Alberta oil sand deposits and a Paleozoic Mississippi Valley-type lead-zinc deposit contain significant Re and Os contents with high {sup 187}Re/{sup 188}Os and radiogenic {sup 187}Os/{sup 188}Os ratios suitable for geochronology. The oil from the 6 Alberta oil sand deposits yields Re-Os analyses with very high Re/{sup 188}Os ratios, and radiogenic Os isotopic compositions. Regression of the Re-Os data yields a date of 116 {+-} 27 Ma. This date plausibly represents the period of in situ radiogenic growth of {sup 187}Os following hydrocarbon migration and reservoir filling. Therefore, directly dating these processes, and this formation age corresponds with recent burial history models for parts of the Western Canada Sedimentary Basin. The very high initial {sup 187}Os/{sup 188}Os for this regression requires rocks much older than Cretaceous for the hydrocarbon source.

Research on supplying potential of uranium source from rocks in western provenance area of Hailaer basin

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Chinese Academy of Geological Sciences, Beijing

2006-01-01

Using U-Pb isotope composition evolution, this paper expounds the initial uranium content in volcanic rocks of provenance area of Xihulitu basin and in granites of provenance area of Kelulun sag, western Hailaer basin. The initial uranium content (U 0 ) in volcanic rocks of provenance area is higher, the average initial uranium content of volcanic rocks is 10.061 x 10 -6 , the average uranium variation coefficient (ΔU) is -49.57%; the average initial uranium content of granites is 18.381 x 10 -6 , the average uranium variation coefficient (ΔU) is -80%. The results indicate that rocks in provenance area could provide the pre-enrichment of uranium in deposited sandstone. U-Ra equilibrium coefficients of rocks indicate that there is obvious U-Ra disequilibrium phenomenon in volcanic rocks, and the time when granites provided uranium source occurred 16000 a ago. (authors)

Water sources for cyanobacteria below desert rocks in the Negev Desert determined by conductivity

OpenAIRE

McKay, Christopher P.

2016-01-01

We present year round meteorological and conductivity measurements of colonized hypolithic rocks in the Arava Valley, Negev Desert, Israel. The data indicate that while dew is common in the Negev it is not an important source of moisture for hypolithic organisms at this site. The dominance of cyanobacteria in the hypolithic community is consistent with predictions that cyanobacteria are confined to habitats supplied by rain. To monitor the presence of liquid water under the small Negev rocks ...

The History of Petroleum Pollution in Malaysia; Urgent Need for Integrated Prevention Approach

Directory of Open Access Journals (Sweden)

Mahyar Sakari

2010-01-01

Full Text Available Petroleum pollution is known as point and non-point source of contaminations in the environment. A major class of petroleum contaminant is groups of compounds consist of two or more fused benzene rings called polycyclic aromatic hydrocarbons (PAHs that are carcinogenic, mutagenic and toxic. Source identification of petroleum pollution is necessary to prevent pollution entry into the environment. Eight sedimentary cores were obtained from developed and developing areas around Peninsular Malaysia to investigate the historical profile of PAHs, their characteristics and its possible origins. The results showed that the PAHs concentrations varied from very minimum to 2400 ng/g d. w. in average quarter century intervals. Most of the studied locations showed high contribution of PAHs from combusted fuel, coal, biomasses and wood materials except for the southern part of Peninsular Malaysia in which revealed dominance of petroleum products. The findings indicate that PAHs are delivered from different intermediate materials such as asphalt, street dust, vehicular emission and crankcase oil. However, there has been a decline of PAHs input into the marine environment in recent years; petroleum is shown to be a significant cause of marine pollution since the second quarter of 20th century. An overview on sourced materials of petroleum pollution indicates multi-approach necessity toward pollution control, regardless of concentration and possible degradation processes. Various sectors both governmental and non-governmental are needed for prevention and control of petroleum pollution where different sources apparently contribute to the pollution generation process.

The petroleum dilemma of Russia

International Nuclear Information System (INIS)

Roubinski, Y.

2004-01-01

Russia is confronted with major choices in the research of an optimum petroleum strategy. Now the first world exporter, Russia takes advantage of the Usa policy, first importer, which aim to diversify their supply sources since the 11 september 2001, to decrease their dependence from the Saudi Arabia and more generally from the instable Middle East. In another hand, Moscow wants to minimize the dependence of the petroleum benefit and the oils prices fluctuations, by a diversification of its economy structure. These choices define a part of the russian policy in the context of the presidential elections of march 2004. (A.L.B.)

New guidelines for oil spill identification of waterborne petroleum and petroleum products

Energy Technology Data Exchange (ETDEWEB)

Faksness, L.G.; Daling, P.S. [SINTEF Energy Research, Trondheim (Norway); Hansen, A.B. [National Environmental Research Inst., Roskilde (Denmark); Kienhuis, P. [RIZA, (Netherlands); Duus, R. [Norwegian Standard Association (Norway)

2005-07-01

Advances in interpretive and analytical methods have opened the possibility to improve the existing Nordtest methodology for oil spill identification which was developed in 1991 under the Nordic Council of Ministers. In 2002, the European Committee for Standardization (CEN) established 2 working groups to revise the Nordtest Methodology into the following 2 CEN guidelines: (1) oil spill identification which includes waterborne and petroleum products, and (2) oil spill identification which in addition to including waterborne petroleum and petroleum products, includes analytical methodology and interpretation of results. The revised methodology includes a protocol/decision chart that has 3 tiered levels of analyses and data treatment. The methodology relies on the characterization of diagnostic ratios. The CEN working group intends to use the guidelines as a basis for a national oil spill identification protocol in each European country and for further international use. The methodology can be applied to oil samples of petrogenic origin with boiling points above 200 degrees C, such as crude oils, diesel fuel oils, residual bunker oils, lubricants, and mixtures of oily bilge and sludge samples. It is not intended for automotive gasolines or other light petroleum products. The method has been implemented in most forensic laboratories in Europe and has successfully differentiated between oils from a spill and possible pollution sources. 19 refs., 4 tabs., 10 figs.

New guidelines for oil spill identification of waterborne petroleum and petroleum products

International Nuclear Information System (INIS)

Faksness, L.G.; Daling, P.S.; Hansen, A.B.; Kienhuis, P.; Duus, R.

2005-01-01

Advances in interpretive and analytical methods have opened the possibility to improve the existing Nordtest methodology for oil spill identification which was developed in 1991 under the Nordic Council of Ministers. In 2002, the European Committee for Standardization (CEN) established 2 working groups to revise the Nordtest Methodology into the following 2 CEN guidelines: (1) oil spill identification which includes waterborne and petroleum products, and (2) oil spill identification which in addition to including waterborne petroleum and petroleum products, includes analytical methodology and interpretation of results. The revised methodology includes a protocol/decision chart that has 3 tiered levels of analyses and data treatment. The methodology relies on the characterization of diagnostic ratios. The CEN working group intends to use the guidelines as a basis for a national oil spill identification protocol in each European country and for further international use. The methodology can be applied to oil samples of petrogenic origin with boiling points above 200 degrees C, such as crude oils, diesel fuel oils, residual bunker oils, lubricants, and mixtures of oily bilge and sludge samples. It is not intended for automotive gasolines or other light petroleum products. The method has been implemented in most forensic laboratories in Europe and has successfully differentiated between oils from a spill and possible pollution sources. 19 refs., 4 tabs., 10 figs

Petroleum and mineral resources of Antarctica

Science.gov (United States)

Kovar, Karel; Behrendt, John Charles

1983-01-01

No known petroleum or mineral resources occur in Antarctica. The data on these subjects have been collected, mainly since the IGY (International Geophysical Year), 1957-58, as a part of other research carried out by geologists and geophysicists from a number of countries. Specific resource-related studies have not been made. Wright and Williams (1974) summarized what was known of Antarctic mineral resources a decade ago.The U.S. Geological Survey has been actively pursuing various investigations in Antarctica since 194 7. In the course of this work and that of our colleagues elsewhere in the United States and in other countries, much information relevant to petroleum and mineral resources has been obtained. Since 1976, modern state-of-the-art multichannel seismic reflection and aeromagnetic surveys by several countries over the continental margin of Antarctica have indicated thick sedimentary basins. However, no offshore drilling beneath the continental shelf has taken place since the DSDP (Deep Sea Drilling Project) holes in the Ross Sea in 1973. Geologic field investigations begun at the turn of the twentieth century have been intensified in the past two decades; most rock outcrops have been visited and samples collected. Technology to exploit resources, particularly in the Arctic, has been developing at a rapid rate, and much of it could be applied to Antarctica. As a result of the petroleum price increases of the past decade, the attention of a number of countries has turned to Antarctica, but under the policy of "voluntary restraint" adopted by the Antarctic Treaty nations, no active petroleum or mineral exploration is taking place. The Antarctic treaty countries are in the process of negotiating an Antarctic mineral resources regime that is anticipated to be completed within the next several years. Therefore it seemed timely to us to readdress the question of petroleum and mineral resources. These reports review and summarize the available information. The

shales: a review of their classifications, properties and importance to ...

African Journals Online (AJOL)

DJFLEX

In the Niger Delta petroleum province, the source rocks and seal rocks are the marine/deltaic, plastic and over-pressured shales of Akata and Agbada Formations. KEY WORDS: Shales, Classification, Strength, Composition, Petroleum Industry, Niger Delta. INTRODUCTION. Shales are fine-grained laminated or fissile.

Statistical handbook for Canada's upstream petroleum industry: '96 updates

International Nuclear Information System (INIS)

1997-01-01

The Statistical Handbook of CAPP is an annual compilation of useful information about the Canadian petroleum and natural gas industry. It has been published since 1955, and is a key source of upstream petroleum statistics. It presents a historical summary of the petroleum industry''s progress and provides detailed statistical information on the production and consumption of petroleum, petroleum products, natural gas and natural gas liquids, imports and exports, land sales, pipelines, reserves, drilling and refinery activities, and prices in Canada. The information, mostly in tabular form, is based on the latest available data (generally up to and including 1996). For the first time in 1997, the Handbook is also made available in CD-ROM format (EXCEL 5.0). Plans are also underway to publish the Handbook on a secure site on the Internet

Enhancement of biodegradation of crude petroleum-oil in contaminated water by the addition of nitrogen sources.

Science.gov (United States)

Mukred, A M; Hamid, A A; Hamzah, A; Yusoff, W M Wan

2008-09-01

Addition of nitrogen sources as supplementary nutrient into MSM medium to enhance biodegradation by stimulating the growth four isolates, Acinetobacter faecalis, Staphylococcus sp., Pseudomonas putida and Neisseria elongata isolated from petroleum contaminated groundwater, wastewater aeration pond and biopond at the oil refinery Terengganu Malaysia was investigated. The organic nitrogen sources tested not only supported growth but also enhances biodegradation of 1% Tapis crude oil. All four isolates showed good growth especially when peptone was employed as the organic nitrogen compared to growth in the basal medium. Gas chromatography showed that more then 91, 93, 94 and 95% degradation of total hydrocarbon was observed after 5 days of incubation by isolates Pseudomonas putida, Neisseria elongate, Acinetobacter faecalis and Staphylococcus sp., respectively.

Updating the U.S. Life Cycle GHG Petroleum Baseline to 2014 with Projections to 2040 Using Open-Source Engineering-Based Models.

Science.gov (United States)

Cooney, Gregory; Jamieson, Matthew; Marriott, Joe; Bergerson, Joule; Brandt, Adam; Skone, Timothy J

2017-01-17

The National Energy Technology Laboratory produced a well-to-wheels (WTW) life cycle greenhouse gas analysis of petroleum-based fuels consumed in the U.S. in 2005, known as the NETL 2005 Petroleum Baseline. This study uses a set of engineering-based, open-source models combined with publicly available data to calculate baseline results for 2014. An increase between the 2005 baseline and the 2014 results presented here (e.g., 92.4 vs 96.2 g CO 2 e/MJ gasoline, + 4.1%) are due to changes both in modeling platform and in the U.S. petroleum sector. An updated result for 2005 was calculated to minimize the effect of the change in modeling platform, and emissions for gasoline in 2014 were about 2% lower than in 2005 (98.1 vs 96.2 g CO 2 e/MJ gasoline). The same methods were utilized to forecast emissions from fuels out to 2040, indicating maximum changes from the 2014 gasoline result between +2.1% and -1.4%. The changing baseline values lead to potential compliance challenges with frameworks such as the Energy Independence and Security Act (EISA) Section 526, which states that Federal agencies should not purchase alternative fuels unless their life cycle GHG emissions are less than those of conventionally produced, petroleum-derived fuels.

76 FR 22825 - Mandatory Reporting of Greenhouse Gases: Petroleum and Natural Gas Systems

Science.gov (United States)

2011-04-25

... Reporting of Greenhouse Gases: Petroleum and Natural Gas Systems AGENCY: Environmental Protection Agency... Subpart W: Petroleum and Natural Gas Systems of the Greenhouse Gas Reporting Rule. As part of the... greenhouse gas emissions for the petroleum and natural gas systems source category of the greenhouse gas...

Source identification of underground fuel spills in a petroleum refinery using fingerprinting techniques and chemo-metric analysis. A Case Study

International Nuclear Information System (INIS)

Kanellopoulou, G.; Gidarakos, E.; Pasadakis, N.

2005-01-01

Crude oil and its refining products are the most frequent contaminants, found in the environment due to spills. The aim of this work was the identification of spill source(s) in the subsurface of a petroleum refinery. Free phase samples were analyzed with gas chromatography and the analytical results were interpreted using Principal Component Analysis (PCA) method. The chemical analysis of groundwater samples from the refinery subsurface was also employed to obtain a comprehensive picture of the spill distribution and origin. (authors)

Petroleum Characterisation and Reservoir Dynamics - The Froey Field and the Rind Discovery, Norwegian Continental Shelf

Energy Technology Data Exchange (ETDEWEB)

Bhullar, Abid G.

1999-07-01

The objective of this thesis is to apply the fundamental principles of petroleum geochemistry integrated with petroleum/reservoir engineering and geological concepts to the dynamics and characterisation of petroleum reservoirs. The study is based on 600 core samples and 9 DST oils from 11 wells in the Froey Field and the Rind Discovery. The work is presented in five papers. Paper 1 is a detailed characterisation of the reservoirs using a petroleum geochemical approach. Paper 2 describes the application of a single reservoir geochemical screening technique to exploration, appraisal and production geology and reservoir/petroleum engineering. Paper 3 compares the Iatroscan TLC-FID screening technique and the extraction efficiency of micro-extraction used in this work with the well-established Rock-Eval geochemical screening method and with the Soxtec extraction method. Paper 4 refines the migration and filling models of Paper 1, and Paper 5 presents a comparison of models of petroleum generation, migration and accumulation based on geochemical data with 1D burial history, a ''pseudo well'' based on actual well data and regional seismic analysis representing the hydrocarbon generative basin conditions.

Addendum to uranium favorability of Cenozoic sedimentary rocks of the Western Snake River Basin, Idaho

International Nuclear Information System (INIS)

Marjaniemi, D.K.; Curry, W.E.; Robins, J.W.

1976-10-01

Eight appendices are included: stratigraphic and lithologic data for sample localities; gamma-ray spectrometric analyses of rock samples; semiquantitative emission spectroscopic analyses of selected rock samples; average concentrations of trace elements in samples analyzed by emission spectroscopy; petrographic analyses of selected samples; uranium analyses of water samples; list of water wells; and list of petroleum test wells

Petroleum geophysics

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The book is compiled from a series of e-learning modules. GeoCLASS is an e-learning system with contents from petroleum geophysics. It is the result of collaboration between professors at the University of Bergen and the University of Oslo, and its material has been used as curriculum in master program courses at these universities for several years. Using a unique feature to GeoCLASS, these advanced scientific topics are presented on multiple levels. The introductions open the door to this vast pool of knowledge, accessible even for high school students. Enter the door, and you enter the modules. Various levels of content are presented, and the more advanced levels can be shielded from the regular user, and only accessed by those with particular interest. The chapters in the book are: Elastic waves; Survey planning; Seismic acquisition; Basic seismic signal theory and processing; Seismic imaging; Seismic attributes; Rock physics; Reservoir monitoring. (AG)

Screening of biosurfactant producers from petroleum hydrocarbon contaminated sources in cold marine environments.

Science.gov (United States)

Cai, Qinhong; Zhang, Baiyu; Chen, Bing; Zhu, Zhiwen; Lin, Weiyun; Cao, Tong

2014-09-15

An overview of literature about isolating biosurfactant producers from marine sources indicated no such producers have been reported form North Atlantic Canada. Water and sediment samples were taken from petroleum hydrocarbon contaminated coastal and offshore areas in this region. Either n-hexadecane or diesel was used as the sole carbon source for the screening. A modified colony-based oil drop collapsing test was used to cover sessile biosurfactant producers. Fifty-five biosurfactant producers belong to genera of Alcanivorax, Exiguobacterium, Halomonas, Rhodococcus, Bacillus, Acinetobacter, Pseudomonas, and Streptomyces were isolated. The first three genera were established after 1980s with interesting characteristics and limited relevant publications. Some of the 55 isolated strains were found with properties such as greatly reducing surface tension, stabilizing emulsion and producing flocculant. Isolates P6-4P and P1-5P were selected to demonstrate the performance of biosurfactant production, and were found to reduce the surface tension of water to as low as 28 dynes/cm. Copyright © 2014 Elsevier Ltd. All rights reserved.

The role of the national petroleum company in petroleum development market

Energy Technology Data Exchange (ETDEWEB)

Lee, B J [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

1997-08-01

The present century started with the creation of national petroleum companies, and it ends with those national petroleum companies exerting various types of efforts to increase the efficiency of their management. Especially, the efforts of these national petroleum companies are ever intensifying to adapt to new trends in the world petroleum market such as intensified competition, ever-deepening price unstableness, separation of structure between upstream and downstream portions, rapid development of petroleum development technologies, change of political systems and the demise of national borders, ever-increasing consciousness of environmental preservation, etc. Korea cannot be exempt from management rationalization efforts of national petroleum companies. Especially, Korea established its own national petroleum company in order to actively deal with these as its supply system is very weak. Therefore, the national petroleum company should create as many successful petroleum development businesses by actively carrying out petroleum development businesses domestically and overseas in order to establish a stable supply system of petroleum and to support the petroleum development businesses of civilian enterprises more effectively. The national petroleum company must, first of all, replace the bureaucracy with entrepreneurship. Esp., in order to enhance the efficiency of management, short- term outcome should not be emphasized over long-term tenure of petroleum development businesses, and excessive interference of government on the national petroleum company should be excluded. The entrepreneurship of the national petroleum company should be pursued in Positive-sum way, and its public image should be actively promoted through this. 35 refs., 11 figs., 32 tabs.

Natural and technologically enhanced sources of radon-222

International Nuclear Information System (INIS)

Travis, C.C.; Watson, A.P.; McDowell-Boyer, L.M.; Cotter, S.J.; Randolph, M.L.; Fields, D.E.

1979-01-01

An assessment of 222 Rn releases (curies/year) from major natural and technologically enhanced sources in the United States is presented. The resulting inhalation population dose commitments to the bronchial epithelium of the lung (lung-rem) are also estimated. The sources of radon considered are natural soil, evapotranspiration, potable water supplies, building materials, natural gas, uranium mining and milling, coal and phosphate mining, phosphate fertilizer, liquefied petroleum gas, geothermal power facilities, coal-fired power plants, and gas and oil wells. The most important natural source of 222 Rn is decay of 226 Ra in the soil and rocks of the earth's crust. This source results in approximately 40% of the total population dose from all sources of radon. The largest technoligcally enhanced contributor to population dose is airborne 222 Rn in building interiors, which is estimated to contribute 55% to the total population exposure to 222 Rn. Each of the other sources is estimated to contribute less than 3% to the total

Petroleum supply monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Multi-elemental characterization of volcanic and vulcano-sedimentary rocks from Pina petroleum ore, central Cuba

International Nuclear Information System (INIS)

Montero-Cabrera, M.E.; Herrera-Peraza, E.; Betancourt-Tanda, L.; Campa-Menendez, R.; Diaz-Rizo, O.; Rodriguez-Martinez, N.; Segura-Soto, R.; Hernandez-Lopez, B.; Valdes-Lopez, S.

1994-01-01

Concentrations of 32 elements in 22 clay, limestone, tuff and volcanic rock samples from the Pina ore have been obtained by neutron activation and X-ray fluorescence analyses. Several LILE (large ion lithofile elements) and REE (rare earth element) concentration diagrams showed the calc-alkaline character of the volcanic rocks corresponding to the Greater Antilles Island, Arc. The basaltic andesite behavior of the rocks studied was confirmed by comparing the average concentrations obtained from tuffs and volcanic rocks with proper mean values of rock elemental compositions of the earth's crust. (Author)

Multi-elemental characterization of volcanic and vulcano-sedimentary rocks from Pina petroleum ore, central Cuba

Energy Technology Data Exchange (ETDEWEB)

Montero-Cabrera, M.E.; Herrera-Peraza, E.; Betancourt-Tanda, L.; Campa-Menendez, R.; Diaz-Rizo, O. (Instituto Superior de Ciencia y Tecnologia Nuclear (ISCTN), La Habana (Cuba)); Rodriguez-Martinez, N.; Segura-Soto, R.; Hernandez-Lopez, B.; Valdes-Lopez, S. (Centro de Investigaciones y Desarrollo del Petroleo, La Habana (Cuba))

1994-08-01

Concentrations of 32 elements in 22 clay, limestone, tuff and volcanic rock samples from the Pina ore have been obtained by neutron activation and X-ray fluorescence analyses. Several LILE (large ion lithofile elements) and REE (rare earth element) concentration diagrams showed the calc-alkaline character of the volcanic rocks corresponding to the Greater Antilles Island, Arc. The basaltic andesite behavior of the rocks studied was confirmed by comparing the average concentrations obtained from tuffs and volcanic rocks with proper mean values of rock elemental compositions of the earth's crust. (Author).

Mass balance constraints on the sources of the petrogenic hydrocarbon background in offshore sediments of Prince William Sound and the Gulf of Alaska

International Nuclear Information System (INIS)

Page, D.S.; Boehm, P.D.; Douglas, G.S.; Brown, J.S.; Bence, A.E.; Burns, W.A.

2000-01-01

A comprehensive sampling program was conducted in 1999 in the offshore sediments of Prince William Sound and the Gulf of Alaska to verify a recent claim that eroding coal beds are the source of petrogenic hydrocarbons background in the area. Samples taken in 1993 and 1994 were reanalyzed to determine concentrations of polycyclic aromatic hydrocarbons (PAH) and chemical biomarkers. Three Bering River coal samples plus 10 archived source-rock and 3 archived Gulf of Alaska seep and field oil samples from exploration activities in the 1960s and 1970s were also analyzed. The linear combination of the analyte distributions of 18 representative sources that most likely matched the compositions of each sample was derived using the least-squares method. Some of the potential contributing sources which were examined for this study included seep oil, eroding source rocks, eroding coal beds, glacial flour, recent terrestrial sources and human activity. It was determined that the recent claim was incorrect. Eroding Tertiary petroleum source rocks and residues of seep oils are the main sources of hydrocarbon background in the area, rather than area coals or residues from the Exxon Valdez oil spill. 10 refs., 2 tabs., 3 figs

Geology and oil and gas assessment of the Todilto Total Petroleum System, San Juan Basin Province, New Mexico and Colorado: Chapter 3 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Hatch, J.R.

2013-01-01

Organic-rich, shaly limestone beds, which contain hydrocarbon source beds in the lower part of the Jurassic Todilto Limestone Member of the Wanakah Formation, and sandstone reservoirs in the overlying Jurassic Entrada Sandstone, compose the Todilto Total Petroleum System (TPS). Source rock facies of the Todilto Limestone were deposited in a combined marine-lacustrine depositional setting. Sandstone reservoirs in the Entrada Sandstone were deposited in eolian depositional environments. Oil in Todilto source beds was generated beginning in the middle Paleocene, about 63 million years ago, and maximum generation of oil occurred in the middle Eocene. In the northern part of the San Juan Basin, possible gas and condensate were generated in Todilto Limestone Member source beds until the middle Miocene. The migration distance of oil from the Todilto source beds into the underlying Entrada Sandstone reservoirs was short, probably within the dimensions of a single dune crest. Traps in the Entrada are mainly stratigraphic and diagenetic. Regional tilt of the strata to the northeast has influenced structural trapping of oil, but also allowed for later introduction of water. Subsequent hydrodynamic forces have influenced the repositioning of the oil in some reservoirs and flushing in others. Seals are mostly the anhydrite and limestone facies of the Todilto, which thin to as little as 10 ft over the crests of the dunes. The TPS contains only one assessment unit, the Entrada Sandstone Conventional Oil Assessment Unit (AU) (50220401). Only four of the eight oil fields producing from the Entrada met the 0.5 million barrels of oil minimum size used for this assessment. The AU was estimated at the mean to have potential additions to reserves of 2.32 million barrels of oil (MMBO), 5.56 billion cubic feet of natural gas (BCFG), and 0.22 million barrels of natural gas liquids (MMBNGL).

Correlation of the Canol Formation source rock with oil from Norman Wells

Energy Technology Data Exchange (ETDEWEB)

Snowdon, L.R.; Brooks, P.W.; Williams, G.K.; Goodarzi, F.

1987-01-01

The source of the oil at Norman Wells has long been assumed to have been the Canol Formation and/or the Bluefish Member of the Hare Indian Formation. These two units are stratigraphically above and below the Kee Scarp Formation reservoir unit respectively, and are both bituminous shales. A wide range of analytical techniques including Rock-Eval pyrolysis, solvent extraction and fractionation, capillary gas chromatography, gas chromatography-mass spectrometry, and white light and fluorescence microscopy has been used to characterize core samples of these two units and two samples of crude oil from the Norman Wells field. Most of the analytical techniques were insufficiently refined to either differentiate the extracts from each other or to make a definitive oil/source rock correlation. Collision activated decomposition coupled with multiple ion detection mass spectrometry (GC-MS-MS) did provide sufficient chemical compositional detail of the oils and the two potential sources to demonstrate that the Canol Formation has been the effective source of the Normal Wells oil whereas the Bluefish Member has not. The level of thermal maturity of the core samples ranges from immature to moderately mature in the vicinity of the Norman Wells field to overmature for the samples obtained to the west and north of the field. The level of thermal maturity of the oil was observed to be somewhat higher than that of the samples of the source formation directly above the field. It was thus inferred that some lateral migration from more mature areas has occurred but the extent of this migration was not necessarily more than a few to tens of kilometers.

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are gathered the results of the year 1999 concerning the petroleum industry in France ('UFIP' data), the market quotations of crude oil, the prices of fuels in France and in Portugal and some news about the petroleum industry in Algeria (privatization, exploration-offshore, repurchase), in Iraq (exports, contracts with foreign companies), in Russian Federation (petroleum pipelines and oil ports constructions) and in Chad (production sharing, offshore sites discoveries). (O.M.)

Petroleum Supply Monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

A Systems Approach to Identifying Exploration and Development Opportunities in the Illinois Basin: Digital Portifolio of Plays in Underexplored Lower Paleozoic Rocks [Part 1 of 2

Energy Technology Data Exchange (ETDEWEB)

Seyler, Beverly; Harris, David; Keith, Brian; Huff, Bryan; Lasemi, Yaghoob

2008-06-30

This study examined petroleum occurrence in Ordovician, Silurian and Devonian reservoirs in the Illinois Basin. Results from this project show that there is excellent potential for additional discovery of petroleum reservoirs in these formations. Numerous exploration targets and exploration strategies were identified that can be used to increase production from these underexplored strata. Some of the challenges to exploration of deeper strata include the lack of subsurface data, lack of understanding of regional facies changes, lack of understanding the role of diagenetic alteration in developing reservoir porosity and permeability, the shifting of structural closures with depth, overlooking potential producing horizons, and under utilization of 3D seismic techniques. This study has shown many areas are prospective for additional discoveries in lower Paleozoic strata in the Illinois Basin. This project implemented a systematic basin analysis approach that is expected to encourage exploration for petroleum in lower Paleozoic rocks of the Illinois Basin. The study has compiled and presented a broad base of information and knowledge needed by independent oil companies to pursue the development of exploration prospects in overlooked, deeper play horizons in the Illinois Basin. Available geologic data relevant for the exploration and development of petroleum reservoirs in the Illinois Basin was analyzed and assimilated into a coherent, easily accessible digital play portfolio. The primary focus of this project was on case studies of existing reservoirs in Devonian, Silurian, and Ordovician strata and the application of knowledge gained to future exploration and development in these underexplored strata of the Illinois Basin. In addition, a review of published reports and exploration in the New Albany Shale Group, a Devonian black shale source rock, in Illinois was completed due to the recent increased interest in Devonian black shales across the United States. The New

Resource Assessment of the In-Place and Potentially Recoverable Deep Natural Gas Resource of the Onshore Interior Salt Basins, North Central and Northeastern Gulf of Mexico

Energy Technology Data Exchange (ETDEWEB)

Ernest A. Mancini; Paul Aharon; Donald A. Goddard; Roger Barnaby

2005-10-28

The principal research effort for Year 2 of the project has been petroleum system characterization and modeling. Understanding the burial, thermal maturation, and hydrocarbon expulsion histories of the strata in the onshore interior salt basins of the North Central and Northeastern Gulf of Mexico areas is important in hydrocarbon resource assessment. The underburden and overburden rocks in these basins and subbasins are a product of their rift-related geohistory. Petroleum source rock analysis and initial thermal maturation and hydrocarbon expulsion modeling indicated that an effective regional petroleum source rock in the onshore interior salt basins and subbasins, the North Louisiana Salt Basin, Mississippi Interior Salt Basin, Manila Subbasin and Conecuh Subbasin, was Upper Jurassic Smackover lime mudstone. The initial modeling also indicated that hydrocarbon generation and expulsion were initiated in the Early Cretaceous and continued into the Tertiary in the North Louisiana Salt Basin and the Mississippi Interior Salt Basin and that hydrocarbon generation and expulsion were initiated in the Late Cretaceous and continued into the Tertiary in the Manila Subbasin and Conecuh Subbasin. Refined thermal maturation and hydrocarbon expulsion modeling and additional petroleum source rock analysis have confirmed that the major source rock in the onshore interior salt basins and subbasins is Upper Jurassic Smackover lime mudstone. Hydrocarbon generation and expulsion were initiated in the Early to Late Cretaceous and continued into the Tertiary.

Tectonic control in source rock maturation and oil migration in Trinidad

Energy Technology Data Exchange (ETDEWEB)

Persad, K.M.; Talukdar, S.C.; Dow, W.G. (DGSI, The Woodlands, TX (United States))

1993-02-01

Oil accumulation in Trinidad were sourced by the Upper Cretaceous calcareous shales deposited along the Cretaceous passive margin of northern South America. Maturation of these source rocks, oil generation, migration and re-migration occurred in a foreland basin setting that resulted from interaction between Caribbean and South American plates during Late Oligocene to recent times. During Middle Miocene-Recent times, the foreland basin experienced strong compressional events, which controlled generation, migration, and accumulation of oil in Trinidad. A series of mature source rock kitchens formed in Late Miocene-Recent times in the Southern and Colombus Basins to the east-southeast of the Central Range Thrust. This thrust and associated fratured developed around 12 m.y.b.p. and served as vertical migration paths for the oil generated in Late Miocene time. This oil migrated into submarine fans deposited in the foreland basin axis and older reservoirs deformed into structural traps. Further generation and migration of oil, and re-migration of earlier oil took place during Pliocene-Holocene times, when later thrusting and wrench faulting served as vertical migration paths. Extremely high sedimentation rates in Pliocene-Pleistocene time, concurrent with active faulting, was responsible for very rapid generation of oil and gas. Vertically migrating gas often mixed with earlier migrated oil in overlying reservoirs. This caused depletion of oil in light hydrocarbons with accompanied fractionation among hydrocarbon types resulting in heavier oil in lower reservoirs, enrichment of light hydrocarbons and accumulation of gas-condensates in upper reservoirs. This process led to an oil-gravity stratification within about 10,000 ft of section.

Canadian Petroleum Products Institute 1996 annual review

International Nuclear Information System (INIS)

1996-01-01

The Canadian Petroleum Products Institute (CPPI) is an association of Canadian companies involved in the downstream sector of the petroleum industry which includes refining, distributing and marketing of petroleum products. CPPI's mandate includes: (1) establishing environmental policies, (2) establishing working relationships with governments to develop public policy, (3) developing guidelines for the safe handling of petroleum products, and (4) providing information about the petroleum industry to the public. Canada's 19 refineries processed an average of 1.5 million barrels of crude oil per day in 1996. Domestic sources of crude made up 61 per cent of crude oil processed in 1996. Total exports during the year amounted to 105 million barrels. Some of the issues that the CPPI focused on during 1996 included the controversy over the future of the octane enhancing fuel additive MMT, fuel quality standards for transportation fuels and reformulated fuels, gasoline pricing, air quality and workplace safety. CPPI members' participation in the Voluntary Challenge and Registry (VCR) program towards reducing greenhouse gas emissions was also discussed. The industry was also actively involved in seeking to improve its refinery wastewater discharges

Revisions to the original extent of the Devonian Shale-Middle and Upper Paleozoic Total Petroleum System

Science.gov (United States)

Enomoto, Catherine B.; Rouse, William A.; Trippi, Michael H.; Higley, Debra K.

2016-04-11

Technically recoverable undiscovered hydrocarbon resources in continuous accumulations are present in Upper Devonian and Lower Mississippian strata in the Appalachian Basin Petroleum Province. The province includes parts of New York, Pennsylvania, Ohio, Maryland, West Virginia, Virginia, Kentucky, Tennessee, Georgia, and Alabama. The Upper Devonian and Lower Mississippian strata are part of the previously defined Devonian Shale-Middle and Upper Paleozoic Total Petroleum System (TPS) that extends from New York to Tennessee. This publication presents a revision to the extent of the Devonian Shale-Middle and Upper Paleozoic TPS. The most significant modification to the maximum extent of the Devonian Shale-Middle and Upper Paleozoic TPS is to the south and southwest, adding areas in Tennessee, Georgia, Alabama, and Mississippi where Devonian strata, including potential petroleum source rocks, are present in the subsurface up to the outcrop. The Middle to Upper Devonian Chattanooga Shale extends from southeastern Kentucky to Alabama and eastern Mississippi. Production from Devonian shale has been established in the Appalachian fold and thrust belt of northeastern Alabama. Exploratory drilling has encountered Middle to Upper Devonian strata containing organic-rich shale in west-central Alabama. The areas added to the TPS are located in the Valley and Ridge, Interior Low Plateaus, and Appalachian Plateaus physiographic provinces, including the portion of the Appalachian fold and thrust belt buried beneath Cretaceous and younger sediments that were deposited on the U.S. Gulf Coastal Plain.

[Analysis of fluorescence spectrum of petroleum-polluted water].

Science.gov (United States)

Huang, Miao-Fen; Song, Qing-Jun; Xing, Xu-Feng; Jian, Wei-Jun; Liu, Yuan; Zhao, Zu-Long

2014-09-01

In four ratio experiments, natural waters, sampled from the mountain reservoir and the sea water around Dalian city, were mixed with the sewage from petroleum refinery and petroleum exploitation plants. The fluorescence spectra of water samples containing only chromophoric dissolved organic matters(CDOM), samples containing only petroleum, and samples containing a mixture of petroleum and CDOM were analyzed, respectively. The purpose of this analysis is to provide a basis for determining the contribution of petroleum substances and CDOM to the total absorption coefficient of the petroleum-contaminated water by using fluorescence technique. The results showed that firstly, CDOM in seawater had three main fluorescence peaks at Ex: 225-230 nm/Em: 320-330 nm, Ex: 280 nm/Em: 340 nm and Ex: 225-240 nm/Em: 430-470 nm, respectively, and these may arise from the oceanic chlorophyll. CDOM in natural reservoir water had two main fluorescence peaks at EX: 240- 260 nm/Em: 420-450 nm and Ex: 310~350 nm/Em: 420--440 nm, respectively, and these may arise from the terrestrial sources; secondly, the water samples containing only petroleum extracted with n-hexane had one to three fluorescence spectral peaksat Ex: 220-240 nm/Em: 320-340 nm, Ex: 270-290 nm/Em: 310-340 nm and Ex: 220-235 nm/Em: 280-310 nm, respectively, caused by their hydrocarbon component; finally, the water samples containing both petroleum and CDOM showed a very strong fluorescence peak at Ex: 230-250 nm/Em: 320-370 nm, caused by the combined effect of CDOM and petroleum hydrocarbons.

Evaluation of the nature, origin and potentiality of the subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well, North Western Desert, Egypt

Directory of Open Access Journals (Sweden)

Mohamed M. El Nady

2015-09-01

Full Text Available The present work aims to evaluate the nature and origin of the source rock potentiality of subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well. This target was achieved throughout the evaluation of total organic carbon, rock Eval pyrolysis and vitrinite reflectance for fifteen cutting samples and three extract samples collected from Khatatba, Alam El Bueib and Kharita formations in the studied well. The result revealed that the main hydrocarbon of source rocks, for the Middle Jurassic (Khatatba Fm. is mainly mature, and has good capability of producing oil and minor gas. Lower Cretaceous source rocks (Alam El Bueib Fm. are mature, derived from mixed organic sources and have fair to good capability to generate gas and oil. Kharita Formation of immature source rocks originated from terrestrial origin and has poor to fair potential to produce gas. This indicates that Khatatba and Alam El Bueib formations take the direction of increasing maturity far away from the direction of biodegradation and can be considered as effective source potential in the Melleiha G-1x well.

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are briefly summarized 1)the OPEC decisions and their consequences concerning the production of petroleum in the world 2)some news about the petroleum industry in Chad and in Iraq 3)some news about the new pipelines constructed or to be constructed in the world 4)some news about the LPG industry (start of a LPG extraction unit in Argentina, legislation in France for LPG vehicles) 4)and some news about the petroleum distribution in France. (O.M.)

Petroleum tax and financial decisions

International Nuclear Information System (INIS)

Stensland, G.; Sunnevaag, K.

1993-03-01

The work presented in this report focuses on tax motivated financial incentives in the Norwegian petroleum tax system. Of particular concern is the effects of the reserve fund requirement in the Joint Stock Companies Act. Our prime concern is the Norwegian petroleum tax system as applicable from January 1992, but for the sake of comparison, we have also examined the ''old'' Norwegian petroleum tax system. The findings presented in this report can be divided in two parts. Based on an overview over the development in debt and equity for the major part of companies operating on the Norwegian continental shelf it seems reasonable to divide the companies in three groups. The first group is companies which is not in a tax paying position, both ''foreign'' and domestic. These companies seem to use debt as their most important capital source. The second group is Norwegian companies in a tax paying position. These companies also seem to use debt as the most important capital source. The last group is ''foreign'' companies in a tax paying position. This is a group of companies that mainly use equity to finance their investments in the offshore sector. The second part of the report tries to explain these observations. In the report we compare the incentive effects in the new petroleum tax system to the old tax system. The incentives to finance investments with debt is stronger in the new tax system. Several explanations emerge. Firstly, in the old tax system the investor got an effective tax deduction of 12.8% for dividends. This is removed in the new system. Secondly, in the new system 78% tax is included in the financial statements after tax profit calculation and the maximum dividend calculation, while in the old tax system the withholding tax was excluded. 31 refs., 13 figs. 2 tabs

Environmental Impacts of Petroleum Production: Initial Results from the Osage-Skiatook Petroleum Environmental Research Sites, Osage County, Oklahoma

Science.gov (United States)

Kharaka, Yousif K.; Otton, James K.

2003-01-01

releases from active and inactive pipes and tank batteries. The leases are typical of many depleted and aging petroleum fields in Osage County, which ranks among the top oil and gas producing counties in Oklahoma with about 39,000 wells. Oil and gas production has occurred in Osage county for over one hundred years, but current production is mainly from stripper wells (averaging ~2.8 bbl/d oil and >30 bbl/d brine) that are shallow, mostly 300-700 m in depth, and produce from several sandstones of Pennsylvanian age. Results to date show that the produced water source is a Na-Ca-Cl brine (~150,000 mg/L total dissolved solids), with relatively high concentrations of Mg, Sr, and NH4, but low SO4 and H2S. With the exception of Fe and Mn, the concentrations of trace metals are low. Results also show that some and, eventually, the bulk, of inorganic salts and some dissolved organic species in the released brine from both sites will reach Skiatook Lake. Results at the 'A' site show that the salts have essentially been removed from the sandy soil which formed in a surficial layer of eolian sand, but degraded and weathered oil persists on the surface of old oil and brine pits, close to sites of old tanks, on old channels that carried oil from tanks to the oil pits and other impacted areas. Results also show a plume of high salinity water (5,000-30,600 mg/L TDS) is present at intermediate depths that extend from below the old oil and brine pits to Skiatook Lake. No liquid petroleum was found in the contaminated groundwater, but soluble petroleum byproducts, including organic acid anions and other volatile organic compounds (VOCs) are present. Results to date clearly show that significant amounts of salts from produced-water releases and petroleum hydrocarbons still remain in the soils and rocks of the impacted area after more than 60 years of natural attenuation. At the 'B' site significant amounts of produced water from the two active brine pits percolate into th

National Institute for Petroleum and Energy Research 1989 annual report

Energy Technology Data Exchange (ETDEWEB)

1990-11-01

Research programs on reservoir rocks petroleum, and enhanced recovery are briefly presented. Topics include: Geotechnology; reservoir assessment and characterization; TORIS Research Support; three phase relative permeability; static pore structure analysis of reservoir rocks; effects of pore structure on oil/contaminants ganglia distribution; development of improved microbial flooding methods; development of improved surfactant flooding systems; development of improved alkaline flooding methods; development of improved mobility-control methods; gas miscible displacement; development of improved immiscible gas displacement methodology; thermal processes for light oil recovery; thermal processes for heavy oil recovery; an application of natural isotopes in groundwater for solving environmental problems; processing and thermodynamics research; thermochemistry and thermophysical properties of organic nitrogen- and diheteroatom-containing compounds; in situ hydrogenation; and fuel chemistry.

Instrumental neutron activation analysis of rocks from Cayajabos petroleum ore

International Nuclear Information System (INIS)

Montero Cabrera, M.E.; Herrera Hernandez, H.; Herrera Peraza, E.; Rodriguez Martinez, N.; Lopez Reyes, M.C.

2000-01-01

The relative INAA method under statistical control was used to measure the concentrations of Sb, La, Eu, Co, Rb, Tb, Cs, Hf, Th, Cr, Lu, Yb, Ce, Sm, Gd, Nd. Rare earth element (REE) Chondrite-normalized patterns are presented. The La cond /Lu cond normalized concentration ratios obtained confirm the carbonaceous character of the rocks

Explosion Source Characteristics in Frozen and Unfrozen Rock

National Research Council Canada - National Science Library

Bonner, Jessie L; Leidig, Mark R; Murphy, Katherine; Dougherty, Sara L; Martin, Randolph J

2008-01-01

.... Central Alaska has abrupt lateral boundaries in discontinuous permafrost, and we detonated 3 shots in frozen, saturated rock and 3 shots nearby in unfrozen, dry rock ranging in size from 200 to 350 Ibs...

Present and future situation of Austrian petroleum supply in consideration of energy economy aspects

Energy Technology Data Exchange (ETDEWEB)

Filip, G

1982-02-02

The author attempts to show the present situation (as of 1979/80) of the Austrian petroleum industry. Section two of the study is, to a certain extent, pointing out the range of activities of the OeMV-AG, which is the most important national petroleum company. Furthermore, the most important data and figures documenting the importance of petroleum and its processing products are mentioned in that section. In many countries the energy source petroleum contributes more than 50% to the total energy supply. Especially for this reason, it is necessary to attribute a certain weight to this energy source in making forecasts. This is considered in detail mainly in the third section, and apart from imports problems and environmental protection also the recent technologies in the field of petroleum production are described. The dissertation ends with a short view to the future energy situation and its problems.

76 FR 80553 - Mandatory Reporting of Greenhouse Gases: Technical Revisions to the Petroleum and Natural Gas...

Science.gov (United States)

2011-12-23

... permeability gas, shale gas, coal seam, or other tight reservoir rock. For example, wells producing coal bed... separation means one or more of the following processes: forced extraction of natural gas liquids, sulfur and... Mandatory Reporting of Greenhouse Gases: Technical Revisions to the Petroleum and Natural Gas Systems...

Water and Proppant Requirements and Water Production Associated with Undiscovered Petroleum in the Bakken and Three Forks Formations, North Dakota and Montana, USA

Science.gov (United States)

Haines, S. S.; Varela, B. A.; Thamke, J.; Hawkins, S. J.; Gianoutsos, N. J.; Tennyson, M. E.

2017-12-01

Water is used for several stages of oil and gas production, in particular for hydraulic fracturing that is typically used during production of petroleum from low-permeability shales and other rock types (referred to as "continuous" petroleum accumulations). Proppant, often sand, is also consumed during hydraulic fracturing. Water is then produced from the reservoir along with the oil and gas, representing either a disposal consideration or a possible source of water for further petroleum development or other purposes. The U.S. Geological Survey (USGS) has developed an approach for regional-scale estimation of these water and proppant quantities in order to provide an improved understanding of possible impacts and to help with planning and decision-making. Using the new methodology, the USGS has conducted a quantitative assessment of water and proppant requirements, and water production volumes, associated with associated with possible future production of undiscovered petroleum resources in the Bakken and Three Forks Formations, Williston Basin, USA. This water and proppant assessment builds directly from the 2013 USGS petroleum assessment for the Bakken and Three Forks Formations. USGS petroleum assessments incorporate all available geologic and petroleum production information, and include the definition of assessment units (AUs) that specify the geographic regions and geologic formations for the assessment. The 2013 petroleum assessment included 5 continuous AUs for the Bakken Formation and one continuous AU for the Three Forks Formation. The assessment inputs are defined probabilistically, and a Monte Carlo approach provides outputs that include uncertainty bounds. We can summarize the assessment outputs with the mean values of the associated distributions. The mean estimated total volume of water for well drilling and cement for all six continuous AUs is 5.9 billion gallons, and the mean estimated volume of water for hydraulic fracturing for all AUs is 164

Black out - The post-petroleum era has started

International Nuclear Information System (INIS)

Enderlin, S.

2009-01-01

The predictable shortage of petroleum resources raises up some worrying questions: how can we get rid of petroleum? What will be our life without petroleum? Will we have enough energy tomorrow to keep the same way of life as today? With what new energy sources tomorrow's world will turn? The author has travelled the world from the Americas to Asia and from Europe to the Persian Gulf to find the leads of the after-petroleum era. From the Chinese coal to the US ethanol, from the nuclear comeback to the Scandinavian innovations, this inquiry makes the world tour of projects, ideas and solutions. First world energy consumer and squanderer, the US hold a prominent place in the energy revolution that Barack Obama election will speed up. In Europe, Germany, Spain and Denmark have taken a serious lead in the green energies race, while China has become recently the first world power of greenhouse gas emissions. (J.S.)

Tucano Sul Basin: petroleum habitat; Bacia de Tucano Sul - habitat do petroleo

Energy Technology Data Exchange (ETDEWEB)

Schaller, Hannfried; Magalhaes, Celso Carvalho; Carvalho, Renato Kramberger

2008-07-01

The South Tucano Basin is located in the State of Bahia, and is an integrating part of the Northeast Brazilian intracratonic graben system which embraces the Jatoba, Tucano (North, Central and South), and Reconcavo Basins. It comprises a Late Jurassic - Early Cretaceous system of half grabens that evolved during the preliminary stages of continental break related to the South Atlantic opening, from which it was aborted during the Aptian. Close to one hundred wells have so far been drilled in the area, leading to the discovery of about 35 million m{sup 3} (220 mmboe) of oil equivalent, comprised in about ten small oil and gas pools, among which Conceicao, Querera, Lagoa Branca, Estacao de Irai and Sempre Viva . Organic shales, that area found in the lower half of the Candeias Fm, are interpreted as the main source rocks, and in regard to the stratigraphic position of the oil pool, three petroleum-systems are recognized in the basin: Candeias-Sergi; Candeias-Candeias, and Candeias-Ilhas. (author)

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

The Chinese Cretaceous Continental Scientific Drilling Project in the Songliao Basin, NE China: Organic-rich source rock evaluation with geophysical logs from Borehole SK-2

Science.gov (United States)

Zhang, X.; Zou, C.

2017-12-01

The Cretaceous strata have been recognized as an important target of oil or gas exploration in the Songliao Basin, northeast China. The second borehole (SK-2) of the Chinese Cretaceous Continental Scientific Drilling Project in the Songliao Basin (CCSD-SK) is the first one to drill through the Cretaceous continental strata in the frame of ICDP. It was designed not only to solve multiple scientific problems (including the Cretaceous paleoenvironment and paleoclimate, as well as deep resources exploration of the Songliao Basin), but also to expect to achieve new breakthroughs in oil and gas exploration. Based on the project, various geophysical log data (including gamma, sonic, resistivity, density etc.) and core samples have been collected from Borehole SK-2. We do research on organic-rich source rocks estimation using various geophysical log data. Firstly, we comprehensively analyzed organic-rich source rocks' geophysical log response characteristics. Then, source rock's identification methods were constructed to identify organic-rich source rocks with geophysical logs. The main identification methods include cross-plot, multiple overlap and Decision Tree method. Finally, the technique and the CARBOLOG method were applied to evaluate total organic carbon (TOC) content from geophysical logs which provide continuous vertical profile estimations (Passey, 1990; Carpentier et al., 1991). The results show that source rocks are widely distributed in Borehole SK-2, over a large depth strata (985 5700m), including Nenjiang, Qingshankou, Denglouku, Yingcheng, Shahezi Formations. The organic-rich source rocks with higher TOC content occur in the Qingshankou (1647 1650m), Denglouku (2534 2887m) and Shahezi (3367 5697m) Formations. The highest TOC content in these formations can reach 10.31%, 6.58%, 12.79% respectively. The bed thickness of organic-rich source rocks in the these formations are totally up to 7.88m, 74.34m, 276.60m respectively. These organic-rich rocks in the

Real-time petroleum spill detection system

International Nuclear Information System (INIS)

Dakin, D.T.

2001-01-01

A real-time autonomous oil and fuel spill detection system has been developed to rapidly detect of a wide range of petroleum products floating on, or suspended in water. The system consists of an array of spill detection buoys distributed within the area to be monitored. The buoys are composed of a float and a multispectral fluorometer, which looks up through the top 5 cm of water to detect floating and suspended petroleum products. The buoys communicate to a base station computer that controls the sampling of the buoys and analyses the data from each buoy to determine if a spill has occurred. If statistically significant background petroleum levels are detected, the system raises an oil spill alarm. The system is useful because early detection of a marine oil spill allows for faster containment, thereby minimizing the contaminated area and reducing cleanup costs. This paper also provided test results for biofouling, various petroleum product detection, water turbidity and wave tolerance. The technology has been successfully demonstrated. The UV light source keeps the optic window free from biofouling, and the electronics are fully submerged so there is no risk that the unit could ignite the vapours of a potential oil spill. The system can also tolerate moderately turbid waters and can therefore be used in many rivers, harbours, water intakes and sumps. The system can detect petroleum products with an average thickness of less than 3 micrometers floating on the water surface. 3 refs., 15 figs

Petroleum supply monthly, July 1999, with data for May 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The Petroleum Supply Monthly (PSM) is one of a family of four petroleum supply publications produced by the Petroleum Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the US and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The Detail Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas--the US (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

Energy Technology Data Exchange (ETDEWEB)

Tellez, G.; Khandan, N.

1995-12-31

The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l; and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.

Results of analyzing natural gas during the use of biochemical processes in a petroleum deposit

Energy Technology Data Exchange (ETDEWEB)

Yulbarisov, E M

1972-01-01

Laboratory and commercial scale experiments with a geobioreagent and the Arlanskii deposit petroleum gave a sharp increase in the content of heavier hydrocarbons, nitrogen, and carbon dioxide in the gas and an increase in the yield of gasoline fraction boiling below 122/sup 0/C. The commercial scale experiments were done in a stratum 1200 m deep during waterflood recovery at 200 kg/cm/sup 2/. A substantial increase in ethane and higher hydrocarbons in the gas and increased petroleum yield were observed, especially after each waterflood. The effect of water was explained by higher activity of the bacteria at a lower concentration of rock salts.

Flow and contaminant transport in fractured rocks

International Nuclear Information System (INIS)

Bear, J.; Tsang, C.F.; Marsily, G. de

1993-01-01

This book is a compilation of nine articles dealing with various aspect of flow in fractured media. Articles range from radionuclide waste to multiphase flow in petroleum reservoirs to practical field test methods. Each chapter contains copious figures to aid the reader, but is also a detailed in-depth analysis of some major flow problem. The subjects covered are as follows: an introduction to flow and transport models; solute transport in fractured rock with application to radioactive waste repositories; solute transport models through fractured networks; theoretical view of stochastic models of fracture systems; numerical models of tracers; multiphase flow models in fractured systems and petroleum reservoirs; unsaturated flow modeling; comparative analysis of various flow modeling techniques in fractured media; and, a summary of field methods for measuring transfers of mass, heat, contaminant, momentum, and electrical charge in fractured media

Paleofacies of Eocene Lower Ngimbang Source Rocks in Cepu Area, East Java Basin based on Biomarkers and Carbon-13 Isotopes

Science.gov (United States)

Devi, Elok A.; Rachman, Faisal; Satyana, Awang H.; Fahrudin; Setyawan, Reddy

2018-02-01

The Eocene Lower Ngimbang carbonaceous shales are geochemically proven hydrocarbon source rocks in the East Java Basin. Sedimentary facies of source rock is important for the source evaluation that can be examined by using biomarkers and carbon-13 isotopes data. Furthermore, paleogeography of the source sedimentation can be reconstructed. The case study was conducted on rock samples of Lower Ngimbang from two exploration wells drilled in Cepu area, East Java Basin, Kujung-1 and Ngimbang-1 wells. The biomarker data include GC and GC-MS data of normal alkanes, isoprenoids, triterpanes, and steranes. Carbon-13 isotope data include saturate and aromatic fractions. Various crossplots of biomarker and carbon-13 isotope data of the Lower Ngimbang source samples from the two wells show that the source facies of Lower Ngimbang shales changed from transitional/deltaic setting at Kujung-1 well location to marginal marine setting at Ngimbang-1 well location. This reveals that the Eocene paleogeography of the Cepu area was composed of land area in the north and marine setting to the south. Biomarkers and carbon-13 isotopes are powerful data for reconstructing paleogeography and paleofacies. In the absence of fossils in some sedimentary facies, these geochemical data are good alternatives.

Determination of in-situ rock stresses related to petroleum activities on the Norwegian Continental Shelf

Energy Technology Data Exchange (ETDEWEB)

Fejerskov, Morten

1996-12-31

In-situ rock stresses have proved to be important for exploration and production of hydrocarbons. This thesis uses various stress determination techniques to characterize the in-situ stress field on the Norwegian Continental Shelf. Leak off tests and borehole breakouts have been used to determine the in-situ stress in deep well bores. Overcoring and earthquake focal mechanisms data have also been compiled and evaluated together with stress information from petroleum wells. A new test procedure is suggested to improve the quality of leak off tests that emphasises the importance of accurate pressure determination, longer test periods and digital data sampling. Four-arm calliper logs are used to identify borehole breakouts on the Tampen Spur and Horda Platform. However, it proved difficult to distinguish borehole breakouts from other drilling processes since the elongations of the borehole consistently appeared in the direction of hole azimuth; drilling-induced key seats are here observed in vertical wells. This behaviour is discussed but not fully understood. This reduces the number of reliable stress data and their quality enormously and even casts some doubt about the quality of previous breakout studies from the North Sea. A highly compressive horizontal stress field seems to be present onshore and offshore Norway. Different stress determination techniques yield very consistent stress orientation, regional and internal variation. A 1. order stress direction is identified, where the maximum horizontal stress direction is rotating from N-S in the Barents Sea to NW-SE in the Norwegian Sea and WNW-ESE in the northern North Sea. At Tampen Spur, a dominant WNW-ESE maximum horizontal stress direction, normal to the major tectonic structures is identified as well as a minimum stress close to the vertical stress, the latter indicating high horizontal stresses. 250 refs., 91 figs., 14 tabs.

10 CFR 503.38 - Permanent exemption for certain fuel mixtures containing natural gas or petroleum.

Science.gov (United States)

2010-01-01

... natural gas or petroleum. 503.38 Section 503.38 Energy DEPARTMENT OF ENERGY (CONTINUED) ALTERNATE FUELS... mixtures containing natural gas or petroleum. (a) Eligibility. Section 212(d) of the Act provides for a... proposes to use a mixture of natural gas or petroleum and an alternate fuel as a primary energy source; (2...

Organic geochemical characterization of terrestrial source rocks of the Triassic Madygen formation (Southern Tien Shan, Kyrgyzstan)

Energy Technology Data Exchange (ETDEWEB)

Berner, U.; Scheeder, G.; Kus, J. [Section Geochemistry of Petroleum and Coal, BGR, Hannover (Germany); Voigt, S.; Schneider, J.W. [Geological Inst., TU Bergakademic Freiberg (Germany)

2009-09-15

Along the northern foothills of the Turkestan-Alai Range (SW Kyrgyzstan), a 1000 to 1500m thick succession of Mesozoic deposits is exposed recording regional changes of the paleo-landscape during Triassic to Cretaceous times. Detailed litho- and biofacies analyses, conducted by the TU Bergakademie Freiberg since 2006, provided for the first time a nearly complete columnar section of the continental Triassic Madygen Formation of Kyrgyzstan. Organic petrographical and organic geochemical methods (including RockEval pyrolyses, and biomarker analyses) have been applied to a suite of terrestrial sedimentary rocks of Triassic age with the intention to identify the depositional environment. Our investigations suggest that the potential source rocks of the terrestrial pluvial Madygen Formation might generate predominantly gaseous hydrocarbons at higher maturities. (orig.)

Mathematical modelling on transport of petroleum hydrocarbons in ...

Indian Academy of Sciences (India)

Groundwater being the world's most extracted raw material, with withdrawal rates .... and analytical results, while Petroleum Hydro-Carbons (PHC) generally ... and pipeline ruptures form the major source of groundwater contamination by ...

Petroleum fiscality indicators

International Nuclear Information System (INIS)

2008-02-01

This document presents the different taxes imposed to petroleum products in France: domestic tax on petroleum products (TIPP) and added value tax (TVA). A comparison is made with the fiscality into effect in other European countries for some petroleum products. Then, the fiscality is detailed for the different petroleum products and automotive fuels with its regional modulations. Finally, the fiscal measures adopted in 2007 are detailed. They concern the transposition of the European directive 2003-96/CE into French right and some fiscal regime changes given to some economical sectors particularly penalized by the rise of petroleum energy prices in 2007. (J.S.)

Petroleum industry 1996

International Nuclear Information System (INIS)

1997-01-01

A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector's companies (oil groups, para-petroleum French industry, scientific and technical research)

Petroleum industry in 2004

International Nuclear Information System (INIS)

2005-01-01

This document presents a detailed outlook of the petroleum industry in the world and more particularly in France in 2005: evolution of crude oil prices; petroleum exploration and production in the world and in France; the French para-petroleum and petroleum industry; the oil supplies; the refining activities; the evolution of products quality and the substitution fuels; the domestic transports, the storage and consumption of petroleum products; the fiscality, prices and distribution of petroleum products. (J.S.)

BASIN ANALYSIS AND PETROLEUM SYSTEM CHARACTERIZATION AND MODELING, INTERIOR SALT BASINS, CENTRAL AND EASTERN GULF OF MEXICO

Energy Technology Data Exchange (ETDEWEB)

Ernest A. Mancini; Donald A. Goddard; Ronald K. Zimmerman

2005-05-10

The principal research effort for Year 2 of the project has been data compilation and the determination of the burial and thermal maturation histories of the North Louisiana Salt Basin and basin modeling and petroleum system identification. In the first nine (9) months of Year 2, the research focus was on the determination of the burial and thermal maturation histories, and during the remainder of the year the emphasis has basin modeling and petroleum system identification. Existing information on the North Louisiana Salt Basin has been evaluated, an electronic database has been developed, regional cross sections have been prepared, structure and isopach maps have been constructed, and burial history, thermal maturation history and hydrocarbon expulsion profiles have been prepared. Seismic data, cross sections, subsurface maps and related profiles have been used in evaluating the tectonic, depositional, burial and thermal maturation histories of the basin. Oil and gas reservoirs have been found to be associated with salt-supported anticlinal and domal features (salt pillows, turtle structures and piercement domes); with normal faulting associated with the northern basin margin and listric down-to-the-basin faults (state-line fault complex) and faulted salt features; and with combination structural and stratigraphic features (Sabine and Monroe Uplifts) and monoclinal features with lithologic variations. Petroleum reservoirs are mainly Upper Jurassic and Lower Cretaceous fluvial-deltaic sandstone facies and Lower Cretaceous and Upper Cretaceous shoreline, marine bar and shallow shelf sandstone facies. Cretaceous unconformities significantly contribute to the hydrocarbon trapping mechanism capacity in the North Louisiana Salt Basin. The chief petroleum source rock in this basin is Upper Jurassic Smackover lime mudstone beds. The generation of hydrocarbons from Smackover lime mudstone was initiated during the Early Cretaceous and continued into the Tertiary

Evolution of wettability in terms of petroleum and petroleum fractions adsorption. An approach by the Wilhelmy method; Evolution de la mouillabilite en fonction de l`adsorption du petrole et de ses fractions. Approche par la methode des angles de contact dynamiques

Energy Technology Data Exchange (ETDEWEB)

Mattos Saliba, A

1996-12-06

Reservoir wettability is very important to petroleum recovery by waterflooding and other processes. It is a key parameter controlling multiphase flow and fluids distribution in a porous medium. Nevertheless, the original water-wetness can be modified by the petroleum`s natural surfactants (asphaltenes and resins) adsorption onto the rock surface. This adsorption may reduce petroleum recovery. In this study, the adsorption of model molecules (pyridine and benzo-quinoline), of rude oil and of its heavier fractions (asphaltenes and resins) has been investigated in terms of wettability alteration for initially water-wet surfaces (glass or quartz). In this case, the dynamic Wilhelmy plate technique provides quantitative values of wetting preference to either oil or water. The results show that, at ambient conditions, adsorption depends on concentration, adsorbent/adsorbate interaction time, pH, solvent type, substrate surface, brine concentration and environment liquid phase (water or oil). However, the initial water film on the surface does not strongly influence this phenomena. (author) 222 refs.

19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

Quantitative determination of minor and trace elements in rocks and soils by spark source mass spectrometry

International Nuclear Information System (INIS)

Ure, A.M.; Bacon, J.R.

1978-01-01

Experimental details are given of the quantitative determination of minor and trace elements in rocks and soils by spark source mass spectrometry. The effects of interfering species, and corrections that can be applied, are discussed. (U.K.)

The petroleum industry in 2003

International Nuclear Information System (INIS)

2004-01-01

This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-11-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

The fate of oil and gas in a constrained natural system - implications from the Bakken petroleum system

Energy Technology Data Exchange (ETDEWEB)

Muscio, G P.A.

1995-07-01

When petroleum is produced from its reservoir at present day, it has already been submitted to a complex array of natural processes, which have left their imprint on its chemical and physical properties. These processes involve the generation of petroleum in its source rock as a function of thermal evolution, and its migration to the reservoir. In order to achieve a better understanding of the effects that these processes have on the nature and occurrence of petroleum, it is crucial to investigate a study area that represents an integrated system encompassing all processes from the beginning of crude oil formation to entrapment. The Bakken Shale petroleum system of the Williston Basin (U.S.A./Canada) appears to fulfil these requirements as it covers a broad range of maturity incorporating all stages of catagenesis, and source and reservoir are closely associated, i.e. Bakken petroleum has not been submitted to long secondary migration routes. Combined with a basinwide uniformity in kerogen type, the latter feature constrains the broad scope of potential influences, and therefore the Bakken petroleum system is an ideal candidate to study petroleum generation, its expulsion and migration under natural conditions. By using a selected set of wells/core samples which were considered to be representative for the entire Bakken petroleum system based on comprehensive screening analyses on both kerogen and bitumen, the present study focussed on the following principal aspects: (1) Evolution of petroleum generation as a function of maturation; (2) Primary migration and distribution of crude oil in a constrained natural system; (3) Occurrence of gas in the immature zone; (4) Evaluation of the natural maturity series with simulation experiments. (orig./HS) [Deutsch] Die Prozesse und Phaenomene der natuerlichen Bildung und Migration von Erdoel und Erdgas laufen waehrend der Katagenese sowohl zeitlich als auch raeumlich zu grossen Teilen parallel zueinander ab und praegen die

Liquefied petroleum gas overexposure in South Africa

African Journals Online (AJOL)

Liquefied petroleum gas (LPG) contains propane and butane gas and is ... source of energy, there are specific health risks to the uninformed user. In SA, LPG is ... the collateral history indicated the gas as the possible agent. • the patient had a ...

hydrocarbons biodegradation and evidence of mixed petroleum

African Journals Online (AJOL)

DJFLEX

MIXED PETROLEUM SOURCE INPUTS TO SURFACE. SEDIMENTS ... environmental risk assessment and remediation efforts. ... (station CR10), a distance of approximately 95km ... Cross River –near Oku Iboku beach area and ... extraction, and evapourated to near dryness ..... Ecological parameters of the mangrove.

Discovery and basic characteristics of high-quality source rocks found in the Yuertusi Formation of the Cambrian in Tarim Basin, China

Directory of Open Access Journals (Sweden)

Guangyou Zhu

2016-02-01

Full Text Available The Upper Paleozoic strata of the Tarim Basin have abundant resources of marine oil and gas. In the Tahe area, Halahatang area, and Tazhong area of the basin, many large-scale oilfields have been found. These oilfields have a confirmed oil and gas reserves worth more than 2.5 billion tons and have completed the annual output of more than 14 million tons of marine oil and gas equivalent. The belief that the only main hydrocarbon source rocks are of the Cambrian or Ordovician is still controversial. Chemists have made significant progress and have effectively lead the oil and gas exploration in Tarim Basin. Due to the complexity of the basin and the limitation of samples, the research work, and fine contrast is restricted. In this article, we investigated the Cambrian strata outcrop of Tarim Basin in detail. By analyzing a lot of outcrops, high-quality hydrocarbon source rocks of Yuertusi Formation have been found in more than 10 outcrop points in Aksu region. The source rocks' lithology is black shale with total organic carbon (TOC content that ranges between 2% and 16%. Total organic carbon (TOC of the black shale layer could be as much as 4%–16%, especially in the outcrops of the Yutixi and Shiairike. This by far is the best marine hydrocarbon source rock that was found in China. The source rocks were distributed consistently in the Aksu region, the thickness of which is about 10–15 m. It was formed in a sedimentary environment of a middle gentle slope to a low gentle slope. Organic matter enrichment is controlled by the upwelling currents. The thick strata of dolostone that developed in the Xiaoerblak Formation are considered to be good reservoirs of the beach and microbial reef in the upper strata of Yuertusi Formation. No hydrocarbon source rocks have been found in the outcrop of Xiaoerblak Formation. The thick strata of gyprock and mudstone development are a set of satisfactory cap layer in the Lower Cambrian. This hydrocarbon

Geophysical Prediction Technology Based on Organic Carbon Content in Source Rocks of the Huizhou Sag, the South China Sea

Directory of Open Access Journals (Sweden)

Yang Wei

2017-08-01

Full Text Available Due to the high exploration cost, limited number of wells for source rocks drilling and scarce test samples for the Total Organic Carbon Content (TOC in the Huizhou sag, the TOC prediction of source rocks in this area and the assessment of resource potentials of the basin are faced with great challenges. In the study of TOC prediction, predecessors usually adopted the logging assessment method, since the data is only confined to a “point” and the regional prediction of the source bed in the seismic profile largely depends on the recognition of seismic facies, making it difficult to quantify TOC. In this study, we combined source rock geological characteristics, logging and seismic response and built the mathematical relation between quasi TOC curve and seismic data based on the TOC logging date of a single well and its internal seismic attribute. The result suggested that it was not purely a linear relationship that was adhered to by predecessors, but was shown as a complicated non-linear relationship. Therefore, the neural network algorithm and SVMs were introduced to obtain the optimum relationship between the quasi TOC curve and the seismic attribute. Then the goal of TOC prediction can be realized with the method of seismic inversion.

Extraction of Iodine from Source Rock and Oil for Radioiodine Dating Final Report CRADA No. TC-1550-98

Energy Technology Data Exchange (ETDEWEB)

Moran, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Summa, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-19

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Exxon Production Research Company (EPR) to develop improved techniques for extracting, concentrating, and measuring iodine from large volumes of source rock and oil. The purpose of this project was to develop a technique for measuring total iodine extracted from rock, obtain isotopic ratios, and develop age models for samples provided by EPR.

Applied Geophysics Opportunities in the Petroleum Industry

Science.gov (United States)

Olgaard, D. L.; Tikku, A.; Roberts, J. C.; Martinez, A.

2012-12-01

Meeting the increasing global demand for energy over the next several decades presents daunting challenges to engineers and scientists, including geoscientists of all disciplines. Many opportunities exist for geophysicists to find and produce oil and gas in a safe, environmentally responsible and affordable manner. Successful oil and gas exploration involves a 'Plates to Pores' approach that integrates multi-scale data from satellites, marine and land seismic and non-seismic field surveys, lab experiments, and even electron microscopy. The petroleum industry is at the forefront of using high performance computing to develop innovative methods to process and analyze large volumes of seismic data and perform realistic numerical modeling, such as finite element fluid flow and rock deformation simulations. Challenging and rewarding jobs in exploration, production and research exist for students with BS/BA, MS and PhD degrees. Geophysics students interested in careers in the petroleum industry should have a broad foundation in science, math and fundamental geosciences at the BS/BA level, as well as mastery of the scientific method, usually gained through thesis work at MS and PhD levels. Field geology or geophysics experience is also valuable. Other personal attributes typical for geoscientists to be successful in industry include a passion for solving complex geoscience problems, the flexibility to work on a variety of assignments throughout a career and skills such as teamwork, communication, integration and leadership. In this presentation we will give examples of research, exploration and production opportunities for geophysicists in petroleum companies and compare and contrast careers in academia vs. industry.

Towards minimizing measurement uncertainty in total petroleum hydrocarbon determination by GC-FID

Energy Technology Data Exchange (ETDEWEB)

Saari, E.

2009-07-01

Despite tightened environmental legislation, spillages of petroleum products remain a serious problem worldwide. The environmental impacts of these spillages are always severe and reliable methods for the identification and quantitative determination of petroleum hydrocarbons in environmental samples are therefore needed. Great improvements in the definition and analysis of total petroleum hydrocarbons (TPH) were finally introduced by international organizations for standardization in 2004. This brought some coherence to the determination and, nowadays, most laboratories seem to employ ISO/DIS 16703:2004, ISO 9377-2:2000 and CEN prEN 14039:2004:E draft international standards for analysing TPH in soil. The implementation of these methods, however, usually fails because the reliability of petroleum hydrocarbon determination has proved to be poor.This thesis describes the assessment of measurement uncertainty for TPH determination in soil. Chemometric methods were used to both estimate the main uncertainty sources and identify the most significant factors affecting these uncertainty sources. The method used for the determinations was based on gas chromatography utilizing flame ionization detection (GC-FID).Chemometric methodology applied in estimating measurement uncertainty for TPH determination showed that the measurement uncertainty is in actual fact dominated by the analytical uncertainty. Within the specific concentration range studied, the analytical uncertainty accounted for as much as 68-80% of the measurement uncertainty. The robustness of the analytical method used for petroleum hydrocarbon determination was then studied in more detail. A two-level Plackett-Burman design and a D-optimal design were utilized to assess the main analytical uncertainty sources of the sample treatment and GC determination procedures. It was also found that the matrix-induced systematic error may also significantly reduce the reliability of petroleum hydrocarbon determination

Nigeria National Petroleum Reserves Asset: Looking Beyond the Niger Delta

International Nuclear Information System (INIS)

Obaje, P. N.

2002-01-01

Nigeria's current national petroleum reserves asset (proven) put at 28 billion barrels of oil and 150 trillion standard cubic feet of gas derives mainly from the Niger Delta onshore and offshore.However, there are opportunities to tremendously add to this asset from the inland basins. These inland basins have continued to frustrate the efforts of many explorers, principally because of their virginity and far distance from existing infrastructure, and for these reasons, many international companies have turned their focus away from frontier onshore to frontier deep-water and ultra deep-water offshore.Petroleum exploration, particularly in the Sudan and Chad Republics has shown that commercial success can be achieved in our own sector, even if it may take some time to put all the elements together. Some pointers have been found from the successes in the other rifted inland basins and the strategies adopted there have been examined in this paper. Congnizance has also been taken of the relative success of Shell's Kolmani River-1 well (33 billion cubit feet of gas) in the Gongola Basin. The paper went ahead to highlight potential petroleum systems in the different sectors of Nigeria's inland basins.Recommendations have also been put forward, which include amongst others (i) the introduction of a JV arrangement that allows State Governments on the inland basins to participate in the exploration for hydrocarbons in their domains (ii) tie future allocation of offshore blocks to acquisition of at least a block in any of the inland basins (iii) initiate a programme of deep drilling and coring of at least one research well to penetrate the entire sedimentary rock successions in each of the inland basins to facilitate a better understanding of their petroleum geology and benefit future exploration campaigns; to be funded and supervised by the Petroleum Technology Development Fund (PTDF)

Burial and thermal history of the Paradox Basin, Utah and Colorado, and petroleum potential of the Middle Pennsylvanian Paradox Basin

Science.gov (United States)

Nuccio, Vito F.; Condon, Steven M.

1996-01-01

The Ismay?Desert Creek interval and Cane Creek cycle of the Alkali Gulch interval of the Middle Pennsylvanian Paradox Formation in the Paradox Basin of Utah and Colorado contain excellent organic-rich source rocks having total organic carbon contents ranging from 0.5 to 11.0 percent. The source rocks in both intervals contain types I, II, and III organic matter and are potential source rocks for both oil and gas. Organic matter in the Ismay?Desert Creek interval and Cane Creek cycle of the Alkali Gulch interval (hereinafter referred to in this report as the ?Cane Creek cycle?) probably is more terrestrial in origin in the eastern part of the basin and is interpreted to have contributed to some of the gas produced there. Thermal maturity increases from southwest to northeast for both the Ismay?Desert Creek interval and Cane Creek cycle, following structural and burial trends throughout the basin. In the northernmost part of the basin, the combination of a relatively thick Tertiary sedimentary sequence and high basinal heat flow has produced very high thermal maturities. Although general thermal maturity trends are similar for both the Ismay?Desert Creek interval and Cane Creek cycle, actual maturity levels are higher for the Cane Creek due to the additional thickness (as much as several thousand feet) of Middle Pennsylvanian section. Throughout most of the basin, the Ismay?Desert Creek interval is mature and in the petroleum-generation window (0.10 to 0.50 production index (PI)), and both oil and gas are produced; in the south-central to southwestern part of the basin, however, the interval is marginally mature (0.10 PI) in the central part of the basin and is overmature (past the petroleum-generation window (>0.50 PI)) throughout most of the eastern part of the basin. The Cane Creek cycle generally produces oil and associated gas throughout the western and central parts of the basin and thermogenic gas in the eastern part of the basin. Burial and thermal

The application of SEM in analyzing the damage to the petroleum reservoirs caused by drilling fluids

International Nuclear Information System (INIS)

Abdul Razak Ismail

1996-01-01

An experimental study has been conducted to analyze the damage to the potential oil and gas reservoirs due to the invasion of drilling fluid during drilling operation. Two types of rock samples representing low and high permeability were used to stimulate the petroleum reservoirs. Sea water based drilling fluids were used in this study. Detail observations to the rock samples were analyzed using scanning electron microscope (SEM). The results of both permeability restoration and SEM observation showed that severe permeability impairments were obtained for high permeability rock. These results indicate that the relative size of the barite particles and the pore size distribution and characteristics of the formation play an important role in determining the damage caused by the drilling fluids

Look! It's Rock'n'roll!

DEFF Research Database (Denmark)

Lindelof, Anja

2007-01-01

, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- Anja Mølle Lindelof. (2007). Look! it's rock'n'roll! how television participated in shaping the visual genre conventions of popular music...... to personal names, capitalization, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- Anja Mølle Lindelof. "Look! It's Rock'n'roll! How television participated in shaping the visual genre....... Pay special attention to personal names, capitalization, and dates. Consult your library or click here for more information on citing sources. -------------------------------------------------------------------------------- TY - JOUR T1 - Look! It's Rock'n'roll! How television participated in shaping...

Crude petroleum-oil biodegradation efficiency of Bacillus subtilis and Pseudomonas aeruginosa strains isolated from a petroleum-oil contaminated soil from North-East India.

Science.gov (United States)

Das, Kishore; Mukherjee, Ashis K

2007-05-01

The efficiency of Bacillus subtilis DM-04 and Pseudomonas aeruginosa M and NM strains isolated from a petroleum contaminated soil sample from North-East India was compared for the biodegradation of crude petroleum-oil hydrocarbons in soil and shake flask study. These bacterial strains could utilize crude petroleum-oil hydrocarbons as sole source of carbon and energy. Bioaugmentation of TPH contaminated microcosm with P. aeruginosa M and NM consortia and B. subtilis strain showed a significant reduction of TPH levels in treated soil as compared to control soil at the end of experiment (120 d). P. aeruginosa strains were more efficient than B. subtilis strain in reducing the TPH content from the medium. The plate count technique indicated expressive growth and biosurfactant production by exogenously seeded bacteria in crude petroleum-oil rich soil. The results showed that B. subtilis DM-04 and P. aeruginosa M and NM strains could be effective for in situ bioremediation.

Petroleum hydrocarbon toxicity to corals: A review.

Science.gov (United States)

Turner, Nicholas R; Renegar, D Abigail

2017-06-30

The proximity of coral reefs to coastal urban areas and shipping lanes predisposes corals to petroleum pollution from multiple sources. Previous research has evaluated petroleum toxicity to coral using a variety of methodology, including monitoring effects of acute and chronic spills, in situ exposures, and ex situ exposures with both adult and larval stage corals. Variability in toxicant, bioassay conditions, species and other methodological disparities between studies prevents comprehensive conclusions regarding the toxicity of hydrocarbons to corals. Following standardized protocols and quantifying the concentration and composition of toxicant will aid in comparison of results between studies and extrapolation to actual spills. Copyright © 2017 Elsevier Ltd. All rights reserved.

Potential displacement of petroleum imports by solar energy technologies

Energy Technology Data Exchange (ETDEWEB)

DeLeon, P.; Jackson, B.L.; McNown, R.F.; Mahrenholz, G.J.

1980-05-01

The United States currently imports close to half of its petroleum requirements. This report delineates the economic, social, and political costs of such a foreign oil dependency. These costs are often intangible, but combined they clearly constitute a greater price for imported petroleum than the strictly economic cost. If we can assume that imported oil imposes significant socioeconomic costs upon the American economy and society, one way to reduce these costs is to develop alternative, domestic energy sources - such as solar energy technologies - which can displace foreign petroleum. The second half of this report estimates that by the year 2000, solar energy technologies can displace 3.6 quads of petroleum. This figure includes solar energy applications in utilities, industrial and agricultural process heat, and transportation. The estimate can be treated as a lower bound; if the United States were to achieve the proposed goal of 20 quads by 2000, the amount of displaced oil probably would be greater. Although all the displaced oil would not be imported, the reduction in imported petroleum would relieve many of the conditions that increase the present cost of foreign oil to the American consumer.

Application of petroleum markers to geochemical and environmental investigations

International Nuclear Information System (INIS)

Abu-Elgheit, M.A.; El-Gayar, M.S.; Hegazi, A.H.

1998-01-01

Application of trace-metal and biological markers to geochemical studies has shown that crude oils could be correlated or differentiated according to their geologic age. The V/Ni, V/Σ Ni, Mg, Fe, and pristine to phytane (Pr/Ph) markers were almost uniform in Gulf of Suez crude oils, revealing their same origin, yet showing marked differences in Western Desert crude oils, reflecting varying degrees of their maturity and migrational history. The significance of petroleum markers was extended to monitoring of oil spill sources. Weathering of spills usually renders their source identification questionable by infrared or gas chromatography profiles. Since evaporative loss light petroleum fractions does not appreciably affect the high-Molecular Weight components with which trace metals, isoprenoids, hopanes, and steranes are associated, V/Ni, Pr/Ph, m/z 191, and m/z 217 mass chromatogram fragments were found reliable in fingerprinting oil spill sources in Mediterranean waters

Petroleum hydrocarbons in offshore sediments from the Gulf

International Nuclear Information System (INIS)

Al-Lihaibi, S.S.; Al-Omran, Laila

1996-01-01

Petroleum hydrocarbons in offshore sediments from the central part of the Gulf were measured using fluorescence spectrophotometry. Concentrations varied between 4.0 and 56.2 μg/g wet sediment (expressed as Kuwait Crude Oil equivalents), with an average of 12.3 μ/g. Highest concentrations were recorded in the north-west sector, with concentrations decreasing in a south-westerly direction. No significant correlations were observed between petroleum hydrocarbons and sedimentary organic carbon (r-0.07), 'mud' content (r=0.09), 'sand' content (r= -0.08) or 'gravel' content (r= -0.12). Distributions of oil are considered to relate more closely to prevailing current and localized pollutant sources in the region. Despite the substantial inputs of oil to the Gulf, contamination can be considered comparatively low, possibly reflecting physical processes and biological degradation which accelerate removal of petroleum from this marine environment. (author)

The petroleum industry in 2005

International Nuclear Information System (INIS)

2006-01-01

This document provides information on the petroleum industry for the year 2005. It discusses the world gas and petroleum markets, the world and french petroleum exploration and production, the petroleum and byproducts industry in France, the hydrocarbons supplying, the refining in France, the evolution of the products and fuels substitution quality, the internal transports of petroleum products, the storage consumption and taxes of petroleum products, the prices and distribution of the petroleum products. (A.L.B.)

Lead isotopes in archaean plutonic rocks

International Nuclear Information System (INIS)

Oversby, V.M.

1978-01-01

Archaean intrusive rocks have initial Pb isotopic compositions which show a varied and complex history for the source regions of the rocks. Even the oldest rocks from Greenland indicate heterogenous U and Pb distribution prior to 3800 m.y. ago. Source regions with μ values less than 7 must have played a significant role in the early history of the earth. By late Archaean time U/Pb ratios of source regions had increased substantially. Data from Australia and North America show distinct regional differences, both within and between continents. (Auth.)

Russian petroleum tax policy – Continuous maneuvering in rocky waters

International Nuclear Information System (INIS)

Fjaertoft, Daniel; Lunden, Lars Petter

2015-01-01

This article maps and analyses petroleum taxation policy in Russia to investigate the extent to which it reaches the goal of maximizing government revenue from new petroleum field developments. Expected cash flows from four real-world fields in Russia are modeled in four real-world tax regimes in an attempt to determine whether the so-called ‘tax maneuver’ of December 2014 helps the government to reach its goal. Russia's tax policy is further analyzed in terms of the desirable tax system design features of simplicity, flexibility, stability and competitiveness. The article concludes that the changes to the tax system introduced additional incentives for field developments but failed both to improve tax system design per se and to maximize government tax revenue. - Highlights: • Petroleum tax revenue is the Russian government’s largest single source of revenue. • Tax legislation has not maximized government revenue from the petroleum industry. • The December 2014 tax reform is just one in a long line of reforms and amendments. • Russian petroleum taxation is set to change perpetually.

Figures on petroleum 1981

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This table taken out from the 1981 annual report 1981 contains an introductory remark on the reorganization of mineral oil statistics up to January 82. It is followed by the tables ranged as follows: refinery capacity and production, crude oil supply, GDR-coverings, import of petroleum products, petroleum consumption, export of petroleum products, transport, oil storage tanks, motor vehicle stock, taxes and tariffs, petroleum export trade, energy consumption and world petroleum numbers. In parts the tables contain comparative figures back to 1950.

Petroleum supply monthly, April 1990

Energy Technology Data Exchange (ETDEWEB)

None

1990-06-26

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the Petroleum Supply Monthly describe (PSM) the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply.'' Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: (1) the Summary Statistics and (2) the Detailed Statistics.

An analysis of natural gas exploration potential in the Qiongdongnan Basin by use of the theory of “joint control of source rocks and geothermal heat”

Directory of Open Access Journals (Sweden)

Zhang Gongcheng

2014-10-01

Full Text Available The Oligocene Yacheng Fm contains the most important source rocks that have been confirmed by exploratory wells in the Qiongdongnan Basin. The efficiency of these source rocks is the key to the breakthrough in natural gas exploration in the study area. This paper analyzes the hydrocarbon potential of each sag in this basin from the perspective of control of both source rocks and geothermal heat. Two types of source rocks occur in the Yacheng Fm, namely mudstone of transitional facies and mudstone of neritic facies. Both of them are dominated by a kerogen of type-III, followed by type-II. Their organic matter abundances are controlled by the amount of continental clastic input. The mudstone of transitional facies is commonly higher in organic matter abundance, while that of neritic facies is lower. The coal-measure source rocks of transitional facies were mainly formed in such environments as delta plains, coastal plains and barrier tidal flat-marshes. Due to the control of Cenozoic lithosphere extension and influence of neotectonism, the geothermal gradient, terrestrial heat flow value (HFV and level of thermal evolution are generally high in deep water. The hot setting not only determines the predominance of gas generation in the deep-water sags, but can promote the shallow-buried source rocks in shallow water into oil window to generate oil. In addition to promoting the hydrocarbon generation of source rocks, the high geothermal and high heat flow value can also speed up the cracking of residual hydrocarbons, thus enhancing hydrocarbon generation efficiency and capacity. According to the theory of joint control of source quality and geothermal heat on hydrocarbon generation, we comprehensively evaluate and rank the exploration potentials of major sags in the Qiongdongnan Basin. These sags are divided into 3 types, of which type-I sags including Yanan, Lingshui, Baodao, Ledong and Huaguang are the highest in hydrocarbon exploration potential.

Petroleum supply monthly, April 1994

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

Climate modeling - a tool for the assessment of the paleodistribution of source and reservoir rocks

Energy Technology Data Exchange (ETDEWEB)

Roscher, M.; Schneider, J.W. [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Geologie; Berner, U. [Bundesanstalt fuer Geowissenschaften und Rohstoffe, Hannover (Germany). Referat Organische Geochemie/Kohlenwasserstoff-Forschung

2008-10-23

In an on-going project of BGR and TU Bergakademie Freiberg, numeric paleo-climate modeling is used as a tool for the assessment of the paleo-distribution of organic rich deposits as well as of reservoir rocks. This modeling approach is based on new ideas concerning the formation of the Pangea supercontinent. The new plate tectonic concept is supported by paleo- magnetic data as it fits the 95% confidence interval of published data. Six Permocarboniferous time slices (340, 320, 300, 290, 270, 255 Ma) were chosen within a first paleo-climate modeling approach as they represent the most important changes of the Late Paleozoic climate development. The digital maps have a resolution of 2.8 x 2.8 (T42), suitable for high-resolution climate modeling, using the PLASIM model. CO{sub 2} concentrations of the paleo-atmosphere and paleo-insolation values have been estimated by published methods. For the purpose of validation, quantitative model output, had to be transformed into qualitative parameters in order to be able to compare digital data with qualitative data of geologic indicators. The model output of surface temperatures and precipitation was therefore converted into climate zones. The reconstructed occurrences of geological indicators like aeolian sands, evaporites, reefs, coals, oil source rocks, tillites, phosphorites and cherts were then compared to the computed paleo-climate zones. Examples of the Permian Pangea show a very good agreement between model results and geological indicators. From the modeling approach we are able to identify climatic processes which lead to the deposition of hydrocarbon source and reservoir rocks. The regional assessment of such atmospheric processes may be used for the identification of the paleo-distribution of organic rich deposits or rock types suitable to form hydrocarbon reservoirs. (orig.)

Study utilization of extractable petroleum hydrocarbons biodegradation waste as the main material for making solid fuels

Science.gov (United States)

Hendrianie, Nuniek; Juliastuti, Sri Rachmania; Ar-rosyidah, Fanny Husna; Rochman, Hilal Abdur

2017-05-01

Nowadays the existence of energy sources of oil and was limited. Therefore, it was important to searching for new innovations of renewable energy sources by utilizing the waste into a source of energy. On the other hand, the process of extractable petroleum hydrocarbons biodegradation generated sludge that had calorific value and untapped. Because of the need for alternative sources of energy innovation with the concept of zero waste and the fuel potential from extractable petroleum hydrocarbons biodegradation waste, so it was necessary to study the use of extractable petroleum hydrocarbons biodegradation waste as the main material for making solid fuel. In addition, sawdust is a waste that had a great quantities and also had a high calorific value to be mixed with extractable petroleum hydrocarbons biodegradation waste. The purpose of this study was to determine the characteristics of the extractable petroleum hydrocarbons biodegradation waste and to determine the potential and a combination of a mixture of extractable petroleum hydrocarbons biodegradation waste and sawdust which has the best calorific value. The variables of this study was the composition of the waste and sawdust as follows 1:1; 1:3; and 3:1 (mass of sawdust : mass of waste) and time of sawdust carbonization was 10, 15 and 20 minutes. Sawdust was carbonized to get the high heating value. The characteristic of main material and fuel analysis performed with proximate analysis. While the calorific value analysis was performed with a bomb calorimeter. From the research, it was known that extractable petroleum hydrocarbons biodegradation waste had a moisture content of 3.06%; volatile matter 19.98%; ash content of 0.56%; fixed carbon content of 76.4% and a calorific value of 717 cal/gram. And a mixture that had the highest calorific value (4286.5 cal/gram) achieved in comparison sawdust : waste (3:1) by carbonization of sawdust for 20 minutes.

Analysis and control of odors from petroleum refineries

International Nuclear Information System (INIS)

O'Brien, M.A.; Duffee, R.A.; Ostojic, N.

1992-01-01

This paper presents a proven approach used to effectively solve odor problems associated with atmospheric emissions from petroleum refineries. A systematic evaluation is first conducted to identify all emissions with the potential for off-site odor impacts. Sampling is then conducted and dynamic dilution olfactometry is used to quantify the odor emission rates of each source. Community odor surveys are performed simultaneously with the source sampling to quantitatively document the downwind odor impacts. Atmospheric dispersion modeling specifically designed for odor is then used to predict instantaneous odor occurrences at various receptor sites under meteorological conditions not actually encountered during the field study. The findings make it possible to rank sources by their odor emission rates and potential for odor impacts in the community. It is then possible to determine how much odor reduction is required to bring the present odor impacts of the individual sources to an acceptable level under worst-case meteorological conditions. Once the degree of control required is determined, control alternatives are selected and evaluated. Case histories have been selected to illustrate the application of this approach at petroleum refineries. They provide descriptions of odor assessment and abatement studies conducted specifically for refinery effluent treatment plant sources as well as process unit emission sources. The sources identified as needing control and the odor abatement measures taken are discussed

Geology and hydrocarbon potential of the Hartford-Deerfield Basin, Connecticut and Massachusetts

Science.gov (United States)

Coleman, James

2016-01-01

The Hartford-Deerfield basin, a Late Triassic to Early Jurassic rift basin located in central Connecticut and Massachusetts, is the northernmost basin of the onshore Mesozoic rift basins in the eastern United States. The presence of asphaltic petroleum in outcrops indicates that at least one active petroleum system has existed within the basin. However, to-date oil and gas wells have not been drilled in the basin to test any type of petroleum trap. There are good to excellent quality source rocks (up to 3.8% present day total organic carbon) within the Jurassic East Berlin and Portland formations. While these source rock intervals are fairly extensive and at peak oil to peak gas stages of maturity, individual source rock beds are relatively thin (typically less than 1 m) based solely on outcrop observations. Potential reservoir rocks within the Hartford-Deerfield basin are arkosic conglomerates, pebbly sandstones, and finer grained sandstones, shales, siltstones, and fractured igneous rocks of the Triassic New Haven and Jurassic East Berlin and Portland formations (and possibly other units). Sandstone porosity data from 75 samples range from less than 1% to 21%, with a mean of 5%. Permeability is equally low, except around joints, fractures, and faults. Seals are likely to be unfractured intra-formational shales and tight igneous bodies. Maturation, generation, and expulsion likely occurred during the late synrift period (Early Jurassic) accentuated by an increase in local geothermal gradient, igneous intrusions, and hydrothermal fluid circulation. Migration pathways were likely along syn- and postrift faults and fracture zones. Petroleum resources, if present, are probably unconventional (continuous) accumulations as conventionally accumulated petroleum is likely not present in significant volumes.

Winters-Domengine Total Petroleum System—Northern Nonassociated Gas Assessment Unit of the San Joaquin Basin Province: Chapter 21 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

Science.gov (United States)

Hosford Scheirer, Allegra; Magoon, Leslie B.

2008-01-01

Stanislaus-San Joaquin county line, which also defines the northern boundary of the San Joaquin Basin Province. In the vertical dimension, the AU extends from the uppermost crystalline basement to the topographic surface (fig. 21.3), to allow for the possibility of down-section charge across fault surfaces and up-dip migration. The gas in this AU may be sourced from the Winters- Domengine(?) petroleum system, located in the Sacramento Valley north of the San Joaquin Valley, as defined by Magoon and others (1994a,b) (question mark notation derives from convention of Magoon and Dow, 1994, and indicates speculative genetic relationship between hydrocarbons and source rock). The Winters-Domengine Total Petroleum System defined for this assessment contains about 7.2 trillion cubic feet (TCF) of known, recoverable gas and includes the Rio Vista gas field, which alone accounts for 4 TCF of recoverable gas through 2002 (CDOGGR, 2003). Alternatively, the northern nonassociated gas may be sourced from the Moreno Formation within the San Joaquin Valley itself.

Source targeting tar balls along the southern Louisiana coastline

International Nuclear Information System (INIS)

Boerts, P.O.; Henry, C.B. Jr.; Overton, E.B.

1993-01-01

Stranded oil and tarballs deposited along the southern coast of Louisiana were source targeted, or compared for petroleum similarities, during 1992. The distribution, frequency, and composition of the stranded oil was assessed for specific study sites covering about 200 miles of the Louisiana coastline. Petroleum transportation off Louisiana shores is in the millions of barrels; with the Louisiana Offshore Oil Port receiving more than 200 million barrels per year. Also contributing to this transportation system are the outer continental shelf production activities, transporting 98 percent of their production by pipeline and 2 percent by barge. The questions addressed here are: What are the sources of the stranded oil and tar found upon the beaches? Are they primarily from small unrelated events, or are they from chronic discharges of identifiable sources? Preliminary data indicates a wide range of petroleum sources, with bunker oils most abundant. The petroleum has undergone varying degrees of weathering, or degradation by environmental processes. Preliminary data indicate relatively undegraded as well as extremely degraded petroleum, with no apparent correlation with study stations. Stations selected along the coastline were biannually surveyed, and petroleum samples collected were quantitatively assessed for petroleum per square meter per station. For a complete chemical assessment, the samples were qualitatively analyzed by detailed gas chromatography/mass spectrometry (GC/MS) characterization and source fingerprinting using selective ion monitoring (SIM). The results were plotted in a cluster matrix to highlight the number of possible sources and the chemical characteristics of the petroleum found

Organic geochemical characterization of potential hydrocarbon source rocks in the upper Benue Trough

International Nuclear Information System (INIS)

Obaje, N. G.; Pearson, M. J.; Suh, C. E.; Dada, S. S.

1999-01-01

The Upper Benue Trough of Nigeria is the northeastern most portion of the Benue rift structure that extends from the northern limit of the Niger Delta in the south to the southern limit of the Chad basin int he northeast. this portion of the trough is made up of two arms: the Gongola Arm and the Yola Arm. Stratigraphic sequence in the Gongola Arm comprises the continental Albian Bima Sandstone, the transitional Cenomanian Yolde Formation and the marine Turonian - Santonian Gongila, Pindiga, and Fika Formations. Overlying these are the continental Campane - Maastrichtian Gombe Sandstone and the Tertiary Kerri - Kerri Formation. In the Yola Arm, the Turonian - Santonian sequence is replaced by the equally marine Dukul, Jessu, Sekuliye Formations, Numanha Shale, and the Lamja Sandstone. Organic geochemical studies have been carried on outcrop sample form the Gongila, Pindiga, Dukul Formations, the Fika shale and the shaly units of the Gombe Sandstone, with the aim of assessing their source rock potential. Gas Chromatography (GC), Gas Chromatography - Mass Spectrometry (C - MS), and Rock Eval Pyrolysis were the major organic geochemical tools employed. Biomaker hydrocarbon signatures obtained from the GC - MS and the Rock Eval Pyrolysis results indicate that all he formations studied, except the Dukul formation, are immature and are all lean in organic matter

Petroleum marketing annual 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-24

The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date.

Petroleum marketing annual 1994

International Nuclear Information System (INIS)

1995-01-01

The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date

Assessment of information needs: Production phase of the petroleum industry for an evaluaton of International Energy Agency Energy Technology Data Exchange

Energy Technology Data Exchange (ETDEWEB)

Linville, B.

1989-09-01

This survey was conducted to determine needs of the petroleum industry for information and data on petroleum production technology, including subjects of most interest and most difficult to obtain, and sources being used to acquire such information. Results of the survey will be used in evaluating the Energy Technology Data Exchange and Department of Energy common data base. A selected sample of world petroleum production specialists and petroleum information specialists and other related personnel were surveyed to learn about their problems in retrieving information and data on petroleum production. They were asked what topics and kinds of information are of current interest, what sources they are using to help resolve their technological problems, what petroleum-producing countries are of interest to them, and other related questions.

Study of variation grain size in desulfurization process of calcined petroleum coke

Science.gov (United States)

Pintowantoro, Sungging; Setiawan, Muhammad Arif; Abdul, Fakhreza

2018-04-01

Indonesia is a country with abundant natural resources, such as mineral mining and petroleum. In petroleum processing, crude oil can be processed into a source of fuel energy such as gasoline, diesel, oil, petroleum coke, and others. One of crude oil potentials in Indonesia is petroleum coke. Petroleum coke is a product from oil refining process. Sulfur reducing process in calcined petroleum cokes can be done by desulfurization process. The industries which have potential to become petroleum coke processing consumers are industries of aluminum smelting (anode, graphite block, carbon mortar), iron riser, calcined coke, foundry coke, etc. Sulfur reducing process in calcined petroleum coke can be done by thermal desulfurization process with alkaline substance NaOH. Desulfurization of petroleum coke process can be done in two ways, which are thermal desulfurization and hydrodesulphurization. This study aims to determine the effect of various grain size on sulfur, carbon, and chemical bond which contained by calcined petroleum coke. The raw material use calcined petroleum coke with 0.653% sulfur content. The grain size that used in this research is 50 mesh, then varied to 20 mesh and 100 mesh for each desulfurization process. Desulfurization are tested by ICP, UV-VIS, and FTIR to determine levels of sulfur, carbon, chemical bonding and sulfur dissolved water which contained in the residual washing of calcined petroleum coke. From various grain size that mentioned before, the optimal value is on 100 mesh grain size, where the sulfur content in petroleum coke is 0.24% and carbon content reaches the highest level of 97.8%. Meanwhile for grain size 100 mesh in the desulfurization process is enough to break the chemical bonds of organic sulfur in petroleum coke.

Risk analysis associated with petroleum hydrocarbons: is everything running smoothly?

International Nuclear Information System (INIS)

Morin, D.

1999-01-01

Petroleum products represent one of the main sources of environmental contamination, and these products are complex, composed of several hundred individual hydrocarbons. The evaluation of the risks associated with petroleum products is often limited by certain specific parameters such as benzene. The petroleum hydrocarbons running from C(10) to C(50) are not often integrated in an analysis of the toxological risks since the toxological characterization of a complex mixture of hydrocarbons is difficult to carry out. There exist in the United States two approaches that were developed recently that allow the integration of various hydrocarbons comprising a mixture. In this presentation, two of these approaches are described and compared. An overview of these approaches related to Canadian regulatory bodies is included, and a case study completes the account. The two approaches that are most well known in this area are: 1) that of the Massachusetts Dept. of Environmental Protection, and 2) that of the Total Petroleum Hydrocarbon Criteria Working Group. The integration of petroleum hydrocarbons in a quantitative evaluation of their toxological risk is possible by present methods. This integration allows a reduction in the uncertainty associated with the use of an integrating parameter in the case of these petroleum hydrocarbons in the C(10) to the C(50) range

Tectonic evolution of the Anadyr Basin, northeastern Eurasia, and its petroleum resource potential

Science.gov (United States)

Antipov, M. P.; Bondarenko, G. E.; Bordovskaya, T. O.; Shipilov, E. V.

2009-09-01

East Anadyr troughs. (3) The middle Miocene resumption of sedimentation was largely related to strike-slip faulting and rifting. In the Miocene to Quaternary, sedimentation was the most intense in the central and northern parts of the Anadyr Basin, as well as in local strike-slip fault-line depressions of the Central Trough. Geological and geophysical data corroborate thrusting in the southern Anadyr Basin. The amplitude of thrusting over the Main River Trough reaches a few tens of kilometers. The vertical thickness of the tectonically screened Paleogene and Neogene rocks in the southern Main River Trough exceeds 10 km. The quantitative forecast of hydrocarbon emigration from Cretaceous and Paleogene source rocks testifies to the disbalance between hydrocarbons emigrated and accumulated in traps of petroleum fields discovered in the Anadyr Basin. The southern portion of the Anadyr Basin is the most promising for the discovery of new petroleum fields in the Upper Cretaceous, Eocene, and Upper Oligocene-Miocene porous and fracture-porous reservoir rocks in subthrust structural and lithological traps.

Petroleum supply monthly, January 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-15

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum supply monthly, October 1993

Energy Technology Data Exchange (ETDEWEB)

1993-10-26

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum Supply Monthly, August 1990

Energy Technology Data Exchange (ETDEWEB)

1990-10-30

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) district movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics.

Petroleum supply monthly, September 1991

Energy Technology Data Exchange (ETDEWEB)

1991-09-30

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

New insights into the stratigraphic, paleogeographic and tectonic evolution and petroleum potential of Kerkennah Islands, Eastern Tunisia

Science.gov (United States)

Elfessi, Maroua

2017-01-01

This work presents general insights into the stratigraphic and paleogeographic evolution as well as the structural architecture and the petroleum potential of Kerkennah Islands, located in the Eastern Tunisia Foreland, from Cenomanian to Pliocene times. Available data from twenty wells mostly drilled in Cercina and Chergui fields are used to establish three lithostratigraphic correlations as well as isopach and isobath maps in order to point out thickness and depth variations of different geological formations present within our study area; in addition to a synthetic log and isoporosity map of the main carbonate reservoir (the nummulites enriched Reineche Member). The integrated geological study reveals relatively condensed but generally continuous sedimentation and a rugged substrate with horsts, grabens and tilted blocks due to the initiation and the individualization of Kerkennah arch throughout the studied geological times. Furthermore, a relationship was highlighted between the evolution of our study zone and those of Sirt basin, Western Mediterranean Sea and Pelagian troughs; this relationship is due to the outstanding location of Kerkennah Islands. The main Bou Dabbous source rock is thicker and more mature within the central-east of the Gulf of Gabes indicating therefore the southeast charge of Reineche reservoir which shows NW-SE trending tilted block system surrounded by normal faults representing the hydrocarbon migration pathways. Besides, the thick Oligo-Miocene formations deposited during the collapse of the Pelagian block caused the maturation of the Ypresian source rock, while the Pliocene unconformity allowed basin inversion and hydrocarbon migration.

Petroleum price

International Nuclear Information System (INIS)

Chevallier, B.

2009-01-01

The 'AFTP' conference on 'petroleum prices' organized by Total last March, tries to explain the different aspects of the crisis we undergo for July 2007 and its consequential effects on the petroleum markets (supply, demand evolvements, impacts on reserves, prices, refining...). (O.M.)

Mechanical Properties and Acoustic Emission Properties of Rocks with Different Transverse Scales

Directory of Open Access Journals (Sweden)

Xi Yan

2017-01-01

Full Text Available Since the stability of engineering rock masses has important practical significance to projects like mining, tunneling, and petroleum engineering, it is necessary to study mechanical properties and stability prediction methods for rocks, cementing materials that are composed of minerals in all shapes and sizes. Rocks will generate acoustic emission during damage failure processes, which is deemed as an effective means of monitoring the stability of coal rocks. In the meantime, actual mining and roadway surrounding rocks tend to have transverse effects; namely, the transverse scale is larger than the length scale. Therefore, it is important to explore mechanical properties and acoustic emission properties of rocks under transverse size effects. Considering the transverse scale effects of rocks, this paper employs the microparticle flow software PFC2D to explore the influence of different aspect ratios on damage mechanics and acoustic emission properties of rocks. The results show that (1 the transverse scale affects uniaxial compression strength of rocks. As the aspect ratio increases, uniaxial compression strength of rocks decreases initially and later increases, showing a V-shape structure and (2 although it affects the maximum hit rate and the strain range of acoustic emission, it has little influence on the period of occurrence. As the transverse scale increases, both damage degree and damage rate of rocks decrease initially and later increase.

Petroleum exploration and development opportunities in Manitoba

International Nuclear Information System (INIS)

Fox, J.N.; Martiniuk, C.D.

1992-01-01

The productive areas of Manitoba are located along the northeastern flank of the Williston basin. Rocks of Paleozoic, Mesozoic and Cenozoic age form a basin-ward thickening wedge of sedimentary strata that reach a total thickness of 2,300 m in the southwest corner of the province. A brief description is presented of the geology and reservoir characteristics of petroleum producing horizons in Manitoba. Manitoba's Crown land tenure system of leases and exploitation reservations is described and an overview of Manitoba's petroleum royalty and tax structure and incentive programs is presented. Exploration and development opportunities in Manitoba are outlined. There are numerous development drilling opportunities along the poorly defined edges of existing pools. Exploration opportunities exist in the Mississippian in the sparsely explored areas outside existing field boundaries. Deeper Devonian and Ordovician horizons, productive elsewhere in the Williston basin, remain relatively untested in Manitoba. An attractive, stable investment climate is created by: availability of land at comparatively low cost; a stable and competitive fiscal regime; incentive programs designed to enhance pay-out; low drilling density; relatively untested deep potential below the Mississippian; low drilling and completion costs; easy access to market; and competitive oil prices. 12 refs., 11 figs., 7 tabs

Petroleum exploration and development opportunities in Manitoba

International Nuclear Information System (INIS)

Fox, J.N.; Martiniuk, C.D.

1991-01-01

The productive areas of Manitoba are located along the northeastern flank of the Williston basin. Rocks of paleozoic, Mesozoic and Cenozoic age form a basin-ward thickening wedge of sedimentary strata that reach a total thickness of 2,300 m in the southwest corner of the province. A brief description is presented of the geology and reservoir characteristics of petroleum producing horizons in Manitoba. Manitoba's Crown land tenure system of leases and exploitation reservations is described and an overview of Manitoba's petroleum royalty and tax structure and incentive programs is presented. Exploration and development opportunities in Manitoba are outlined. There are numerous development drilling opportunities along the poorly defined edges of existing pools. Exploration opportunities exist in the Mississippian in the sparsely explored areas outside existing field boundaries. Deeper Devonian and Ordovician horizons, productive elsewhere in the Williston basin, remain relatively untested in Manitoba. An attractive, stable investment climate is created by: availability of land at comparatively low cost; a stable and competitive fiscal regime; incentive programs designed to enhance pay-out; low drilling density; relatively untested deep potential below the Mississippian; low drilling and completion costs; easy access to market; and competitive oil prices. 12 refs., 11 figs., 7 tabs

77 FR 56421 - Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...

Science.gov (United States)

2012-09-12

... Parts 9 and 60 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...-9672-3] RIN 2060-AN72 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007...

Geochemistry characterization, biomarker and determination of correlation, maturity of petroleum from Bangko-Rohil and Duri Bengkalis, Riau

Science.gov (United States)

Tamboesai, Emrizal Mahidin

2017-11-01

Petroleum is the main source of the energy for industry, transportation. Thedemand for crude oil in Indonesia is much higher than its production which leads to current energy crisis. One of solutions for this crisis is to conduct correlation study, which determines the genetic relationship at each oil well. This study is aimed to provide the indication of the genetic relationship (source matter, source rock and the origins) of Bangko and Duri crude oil. The saturated fraction was analyzed using Gas Chromatography (GC). On the basis of the abundance of hydrocarbon aliphatic, the crude oils samples have small ratio value, which is 0,38-0,50 forPr/n-C17 and 0,16-0,18Ph/n-C18. This values indicated that the samples were originated from higher vascular plants (terrestrial). The samples derived from lacustrine environments (lake) have ratio valueof Pr/Ph (2,50-2,90). The calculation from Star diagram have showed that the oil samples in area MB-07, MB-076 dan MB-172 of Bangko with the oil sample in Duri (MD-01) are negatively correlated. The negative correlation indicated that the oil samples have different the genetic relationship source matter and different in enhance oil recovery.

Applying petroleum biomarkers as a tool for confirmation of petroleum hydrocarbons in high organic content soils

Energy Technology Data Exchange (ETDEWEB)

O' Sullivan, G.; Martin, E.J.; Waddell, J.; Sandau, C.D. [TRIUM Environmental Solutions, Cochrane, AB (Canada); Denham, G. [Nexen Inc., Calgary, AB (Canada); Samis, M.W. [Great Plains Environmental Management Ltd., Medecine Hat, AB (Canada)

2009-10-01

It is often difficult to separate naturally occurring phytogenic organic materials from petrogenic sources in routine gas chromatography flame ionization detection (GC-FID) analyses. Phytogenic compounds include tannins, waxes, terpenes, fats and oils. This study examined the use of petroleum biomarkers as a means of determining the nature, sources, type and geological conditions of the formation of petroleum hydrocarbons (PHCs). The analysis was conducted at a former well site consisting of low-lying peat marshlands that had the potential to interfere with the delineation of PHC impacts. Fourteen boreholes and 8 hand auger holes were placed at the site. Soil samples were analyzed for salinity, metals, and PHC constituents. Biomarker targets included acyclic isoprenoid compounds, polycyclic aromatic hydrocarbon (PAH) compounds, terpanes, hopanes, and triaromatic steranes. A grain-size analysis showed the presence of peat materials within the saturated zone. Results of the study demonstrated the presence of PHC constituents that exceeded applicable guidelines. The biomarker analysis was used to statistically determine site-specific background levels of hydrocarbons. Nearly 3000 tonnes of soil were excavated from the site. It was concluded that site-specific conditions should be taken into consideration when evaluating reclamation targets. 3 refs., 6 figs.

Petroleum service projects in the Gulf of Guinea

Science.gov (United States)

Ken-Worgu, Kenneth Chukwumeka

2011-07-01

The goal of this record of study is to examine the major facets involved in managing several petroleum service projects located in three different countries in the Gulf of Guinea simultaneously, while effectively engaging in business development activities for the Oil and Industrial Services Group (OIS). This work also furnishes adequate background on related subject matters to enable understanding of the projects presented. The petroleum services sector is the back bone of the oil and gas industry. Services companies are vital to the success of all petroleum and energy producers in the USA, the Gulf of Guinea and the world. There is a need and demand for these service companies because they play various roles such as logistics, drilling, construction, dredging, pipe laying, procurement, food supply, human resource supply, etc. The Gulf of Guinea comprises of countries from west and central Africa. This project was limited to Nigeria, Equatorial Guinea and Cameroon. This area holds the largest petroleum reserves in Africa and plays a vital role in the global supply of petroleum. The Oil and Industrial Services Group (OIS), plans to establish herself as one of the leading petroleum service companies in this gulf. To manage this expansion, I have taken the role of Gulf of Guinea manager to apply my background as a petroleum engineer as well as my business skills to build a successful division of the company. This work provides a record of study of the management of services, projects and contracts carried out by the OIS group in the gulf of Guinea. The following are the specific projects in the Gulf of Guinea that I participated in: Managing delivering, maintenance and marketing of offshore vessels, Offshore pipe laying project, Integrated pipeline maintenance project, Development a petroleum technical training facilities, Agbami pipe insulation project, Engineering lift project and Capital budgeting analysis for potential investments. The details of the specific

Photolysis of petroleum

International Nuclear Information System (INIS)

Bobra, M.

1992-05-01

A study was conducted to examine the chemical and physical changes that occur in oils as a result of photooxidation. A literature review of recent studies in petroleum photochemistry revealed reported effects of photo-induced reactions in petroleum, including changes in color, polymerization, solidification, increases in solubility and toxicity, and changes in interfacial properties. A list of products reported as a result of photolysis of petroleum is presented, including such compounds as aldehydes, ketones, esters, and lactones. The photoreactivity of various petroleum components is discussed and mechanisms of photooxidation of petroleum are suggested. In the experimental portion of the study, a variety of crude oils and petroleum products were used to determine how different oils are affected by photolysis, and to examine the importance of photolysis as a weathering process. Photooxidation products from several oils were isolated and identified, including aliphatic and aromatic acids, alcohols, and phenols. Some physical manifestations attributed to photolysis included yellowing, formation of precipitates or crusts, increases in density and viscosity with time, increases of asphaltene content in some oils, changes in pH of the surrounding water, and emulsification. 51 refs., 38 figs., 18 tabs

Petroleum supply monthly, January 1994

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Facts 2000. The Norwegian Petroleum Sector

International Nuclear Information System (INIS)

2000-02-01

Petroleum production on the Norwegian continental shelf (NCS) in the North Sea, the Norwegian Sea and the Barents Sea totalled 2.7 bn scm oil equivalents (oe) up to 1998. Per December 1999, remaining reserves totalled 1.5 bn scm of oil, 1.2 bn scm oe gas and 0.2 bn scm oe of NGL/condensate. Twenty-eight exploration wells were completed or temporarily abandoned on the NCS in 1999. By 31 December 1999, 967 exploration wells had been completed or temporarily abandoned off Norway. Discoveries totalled 45-60 mill scm of oil and 45-70 bn scm of gas. Governmental approval was given in 1999 for the Tune, Borg and Sygna developments. Investment in exploration, field development and pipeline transport totalled about NOK 67 bn in 1998. Oil and gas production in 1999 was roughly on the par with 1998, while NGL/condensate sales rose by 19 per cent. The Balder, Gullfaks South, Jotun, Oseberg East, Visund and Aasgard projects came on stream during 1999. It is estimated that, with the present production rate, Norway's remaining discovered oil resources will last for 17 years, and gas, 93 years. The estimated value of Norwegian petroleum export in 1999 was NOK 168 bn, which is about 36% of the country's total earnings from foreign sales. Published by the Norwegian Ministry of Petroleum and Energy, the book is a major source of information on the Norwegian offshore petroleum activities

Facts 2000. The Norwegian Petroleum Sector

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-02-01

Petroleum production on the Norwegian continental shelf (NCS) in the North Sea, the Norwegian Sea and the Barents Sea totalled 2.7 bn scm oil equivalents (oe) up to 1998. Per December 1999, remaining reserves totalled 1.5 bn scm of oil, 1.2 bn scm oe gas and 0.2 bn scm oe of NGL/condensate. Twenty-eight exploration wells were completed or temporarily abandoned on the NCS in 1999. By 31 December 1999, 967 exploration wells had been completed or temporarily abandoned off Norway. Discoveries totalled 45-60 mill scm of oil and 45-70 bn scm of gas. Governmental approval was given in 1999 for the Tune, Borg and Sygna developments. Investment in exploration, field development and pipeline transport totalled about NOK 67 bn in 1998. Oil and gas production in 1999 was roughly on the par with 1998, while NGL/condensate sales rose by 19 per cent. The Balder, Gullfaks South, Jotun, Oseberg East, Visund and Aasgard projects came on stream during 1999. It is estimated that, with the present production rate, Norway's remaining discovered oil resources will last for 17 years, and gas, 93 years. The estimated value of Norwegian petroleum export in 1999 was NOK 168 bn, which is about 36% of the country's total earnings from foreign sales. Published by the Norwegian Ministry of Petroleum and Energy, the book is a major source of information on the Norwegian offshore petroleum activities.

Facts 2000. The Norwegian Petroleum Sector

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-02-01

Petroleum production on the Norwegian continental shelf (NCS) in the North Sea, the Norwegian Sea and the Barents Sea totalled 2.7 bn scm oil equivalents (oe) up to 1998. Per December 1999, remaining reserves totalled 1.5 bn scm of oil, 1.2 bn scm oe gas and 0.2 bn scm oe of NGL/condensate. Twenty-eight exploration wells were completed or temporarily abandoned on the NCS in 1999. By 31 December 1999, 967 exploration wells had been completed or temporarily abandoned off Norway. Discoveries totalled 45-60 mill scm of oil and 45-70 bn scm of gas. Governmental approval was given in 1999 for the Tune, Borg and Sygna developments. Investment in exploration, field development and pipeline transport totalled about NOK 67 bn in 1998. Oil and gas production in 1999 was roughly on the par with 1998, while NGL/condensate sales rose by 19 per cent. The Balder, Gullfaks South, Jotun, Oseberg East, Visund and Aasgard projects came on stream during 1999. It is estimated that, with the present production rate, Norway's remaining discovered oil resources will last for 17 years, and gas, 93 years. The estimated value of Norwegian petroleum export in 1999 was NOK 168 bn, which is about 36% of the country's total earnings from foreign sales. Published by the Norwegian Ministry of Petroleum and Energy, the book is a major source of information on the Norwegian offshore petroleum activities.

Petroleum marketing monthly, July 1994

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum supply monthly, August 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-26

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

46 CFR 148.04-15 - Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture).

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture). 148.04-15 Section 148.04-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Certain Material § 148.04-15 Petroleum coke, uncalcined; petroleum coke, uncalcined and...

Characteristics of source rocks of the Datangpo Fm, Nanhua System, at the southeastern margin of Sichuan Basin and their significance to oil and gas exploration

Directory of Open Access Journals (Sweden)

Zengye Xie

2017-11-01

Full Text Available In recent years, much attention has been paid to the development environment, biogenetic compositions and hydrocarbon generation characteristics of ancient source rocks in the deep strata of the Sichuan Basin because oil and gas exploration extends continuously to the deep and ultra-deep strata and a giant gas field with the explored reserves of more than 1 × 1012 m3 was discovered in the Middle and Upper Proterozoic–Lower Paleozoic strata in the stable inherited paleo-uplift of the central Sichuan Basin. Based on the previous geological research results, outcrop section of the Datangpo Fm, Nanhua System, at the southeastern margin of the Sichuan Basin was observed and the samples taken from the source rocks were tested and analyzed in terms of their organic geochemistry and organic petrology. It is shown that high-quality black shale source rocks of the Datangpo Fm are developed in the tensional background at the southeastern margin of the Sichuan Basin between two glacial ages, i.e., Gucheng and Nantuo ages in the Nanhua Period. Their thickness is 16–180 m and mineral compositions are mainly clay minerals and clastic quartz. Besides, shale in the Datangpo Fm is of high-quality sapropel type source rock with high abundance at an over-mature stage, and it is characterized by low pristane/phytane ratios (0.32–0.83, low gammacerane abundance, high-abundance tricyclic terpane and higher-content C27 and C29 gonane, indicating that biogenetic compositions are mainly algae and microbes in a strong reducing environment with low salinity. It is concluded that the Datangpo Fm source rocks may be developed in the rift of Nanhua System in central Sichuan Basin. Paleo-uplifts and paleo-slopes before the Caledonian are the favorable locations for the accumulation of dispersed liquid hydrocarbons and paleo-reservoirs derived from the Datangpo Fm source rocks. In addition, scale accumulation zones of dispersed organic matter cracking gas and paleo

The influence of petroleum products on the methane fermentation process.

Science.gov (United States)

Choromański, Paweł; Karwowska, Ewa; Łebkowska, Maria

2016-01-15

In this study the influence of the petroleum products: diesel fuel and spent engine oil on the sewage sludge digestion process and biogas production efficiency was investigated. Microbiological, chemical and enzymatic analyses were applied in the survey. It was revealed that the influence of the petroleum derivatives on the effectiveness of the methane fermentation of sewage sludge depends on the type of the petroleum product. Diesel fuel did not limit the biogas production and the methane concentration in the biogas, while spent engine oil significantly reduced the process efficacy. The changes in physical-chemical parameters, excluding COD, did not reflect the effect of the tested substances. The negative influence of petroleum products on individual bacterial groups was observed after 7 days of the process, while after 14 days probably some adaptive mechanisms appeared. The dehydrogenase activity assessment was the most relevant parameter to evaluate the effect of petroleum products contamination. Diesel fuel was probably used as a source of carbon and energy in the process, while the toxic influence was observed in case of spent engine oil. Copyright © 2015 Elsevier B.V. All rights reserved.

Geochemistry of coal-measure source rocks and natural gases in deep formations in Songliao Basin, NE China

Energy Technology Data Exchange (ETDEWEB)

Mi, Jingkui; Zhang, Shuichang; Hu, Guoyi; He, Kun [State Key Laboratory for Enhanced Oil Recovery, Beijing (China); Petroleum Geology Research and Laboratory Center, Research Institute of Petroleum Exploration and Development, PetroChina (China); Key Laboratory for Petroleum Geochemistry, China National Petroleum Corp. (China)

2010-12-01

The natural gases developed in deep volcanic rock reservoirs of the Songliao Basin, NE China are characterized by enriched {delta}{sup 13}C value for methane and frequently reversal carbon isotopic distribution pattern. Although many researchers consider such gas type as an abiogenic origin, we believe the natural gases have a biogenic origin mainly except little inorganic gases and the reversal carbon isotopic distribution pattern of gases is caused by mixing of different origin gases. Methane carbon isotopic values for majority samples fall in the range from - 24 permille to - 32 permille, which is heavier than typical coal-type gases in other Chinese basins. There are several reasons caused heavy carbon isotope of methane: (1) Carbon isotopic values of source kerogen are 3-5 permille heavier than these from other basins; (2) Source rocks are at extremely high maturity stage with vitrinite reflectance mostly above 3.0%; (3) Portion of gas is derived from basement mudrock or slate with higher maturity. The observation on the organic from deep formation reveals that there is a relatively high content for liptinite, which reaches approximately 8 to 10%. The macerals component of source rock shows that the source rocks have some ability to generate oil. Small portion of oil was generated from high hydrogen content macerals in coals and shales as proof by oil found in microcrack and in micropore of coal and oil-bearing fluid inclusions grown in volcanic reservoir. The occurrence of pyrobitumen in volcanic reservoir indicates preexisted oil had been cracked into wet gas, and this kind of gas had also been found in gas pools. Heavy isotopic methane is derived from coal at extremely high maturity stage. There may be little inorganic alkane gases in deep layers for their geochemistry and special geological setting of Songliao Basin. Artificial mixing experiments of different origins gases confirm that inorganic gas such as gas from well FS1 mixed with other end members

Petroleum Supply Monthly, July 1990

Energy Technology Data Exchange (ETDEWEB)

1990-09-28

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum products : part 1 - overview and prospects

International Nuclear Information System (INIS)

1996-01-01

The petroleum products industry represents the downstream (refining and products marketing) portion of the oil industry. It includes companies that refine crude oil into petroleum products, transport them to distribution storage terminals and sell them directly to major users or wholesale and retail outlets. Issues regarding investment and financing, trade and export strategies, technological innovation and adaptation, human resources, the environment and sustainable development within the sector are discussed, illustrating, among other things, how government and industry can commit to mutually beneficial goals and actions. The petroleum industry is a major source of revenue for Canadian governments which collect about $9 billion annually in federal and provincial taxes on gasoline alone. The industry is capital-intensive and very competitive, with a strong domestic focus. Key points relevant to the sector are examined from the global, North American and Canadian perspectives, highlighting changing conditions and industry responses in both the refining and retailing segments of the sector. Growth prospects in terms of profitability and environmental issues were also analyzed. 11 figs

Characteristics of petroleum contaminants and their distribution in Lake Taihu, China.

Science.gov (United States)

Guo, Jixiang; Fang, Jia; Cao, Jingjing

2012-08-31

Taihu Lake is a typical plain eutrophic shallow lake. With rapidly economic development of the lake area, the petroleum products and oil wastewater produced in various processes have been inevitably discharged into Taihu Lake. As the major fresh water resource in the economically developed region of Yangtze River Delta, the water quality and environmental condition of Taihu Lake have the direct bearing on the natural environment and sustainable development of economy in this region. For this reason we carried out the study to explore the composition, distribution characteristics and sources of petroleum contaminants in Taihu Lake. The aim of this study was to provide the basis for standard management and pollution control of the Taihu Lake environment. The result showed that water samples from near industrial locations were of relatively higher petroleum contaminants concentrations. The oil pollutants concentrations in different areas of Lake Taihu ranged from 0.106 mg/L to 1.168 mg/L, and the sequence of total contents distribution characteristics of petroleum pollutants from high to low in different regions of Taihu Lake was: "Dapu", "Xiaomeikou", "Zhushan Bay", "Lake center", "Qidu". The results showed that total concentrations of n-alkanes and PAHs ranged from 0.045 to 0.281 mg/L and from 0.011 to 0.034 mg/L respectively. In the same region, the concentrations of hydrocarbon pollutants in the surface and bottom of the lake were higher than that in the middle. This paper reached a conclusion that the petroleum contaminants in Taihu Lake mainly derived from petroleum pollution caused by human activities as indicated by OEP, bimodal distribution, CPI, Pr/Ph ratio, the LMW/HMW ratio and other evaluation indices for sources of n-alkanes and polycyclic aromatic hydrocarbons (PAHs).

Cenozoic basin thermal history reconstruction and petroleum systems in the eastern Colombian Andes

Science.gov (United States)

Parra, Mauricio; Mora, Andres; Ketcham, Richard A.; Stockli, Daniel F.; Almendral, Ariel

2017-04-01

Late Mesozoic-Cenozoic retro-arc foreland basins along the eastern margin of the Andes in South America host the world's best detrital record for the study of subduction orogenesis. There, the world's most prolific petroleum system occur in the northernmost of these foreland basin systems, in Ecuador, Colombia and Venezuela, yet over 90% of the discovered hydrocarbons there occur in one single province in norteastern Venezuela. A successful industry-academy collaboration applied a multidisciplinary approach to the study of the north Andes with the aim of investigating both, the driving mechanisms of orogenesis, and its impact on hydrocarbon accumulation in eastern Colombia. The Eastern Cordillera is an inversion orogen located at the leading edge of the northern Andes. Syn-rift subsidence favored the accumulation of km-thick organic matter rich shales in a back-arc basin in the early Cretaceous. Subsequent late Cretaceous thermal subsidence prompted the accumulation of shallow marine sandstones and shales, the latter including the Turonian-Cenomanian main hydrocarbon source-rock. Early Andean uplift since the Paleocene led to development of a flexural basin, filled with mainly non-marine strata. We have studied the Meso-Cenozoic thermal evolution of these basins through modeling of a large thermochronometric database including hundreds of apatite and zircon fission-track and (U-Th)/He data, as well as paleothermometric information based on vitrinite reflectance and present-day temperatures measured in boreholes. The detrital record of Andean construction was also investigated through detrital zircon U-Pb geochronometry in outcrop and borehole samples. A comprehensive burial/exhumation history has been accomplished through three main modeling strategies. First, one-dimensional subsidence was used to invert the pre-extensional lithospheric thicknesses, the magnitude of stretching, and the resulting heat flow associated to extension. The amount of eroded section and

Spatial distribution and sources of heavy metals and petroleum hydrocarbon in the sand flats of Shuangtaizi Estuary, Bohai Sea of China.

Science.gov (United States)

Yang, Xiaolong; Yuan, Xiutang; Zhang, Anguo; Mao, Yuze; Li, Qiang; Zong, Humin; Wang, Lijun; Li, Xiaodong

2015-06-15

The concentrations of heavy metals and petroleum hydrocarbons (PHCs) in surface sediments were investigated in the sand flats of Shuangtaizi Estuary, Bohai Sea of China in May, 2013. Ecological risk assessment indicated that most heavy metals cause low ecological risk to the estuarine environment, with the exception of Cd and Hg (considerable and moderate risk, respectively). Principal component analysis in combination with correlation analysis among heavy metals, PHCs and geological factors (e.g., granularity) was used to identify possible sources of pollutants in Shuangtaizi Estuary. Results showed that the main pollution sources of the area come from anthropogenic factors, such as sewage discharge and oil exploitation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of source rocks and groundwater radioactivity at the Chihuahua valley

Energy Technology Data Exchange (ETDEWEB)

Renteria V, M.; Montero C, M.E.; Reyes C, M.; Herrera P, E.F.; Valenzuela H, M. [Centro de lnvestigacion en Materiales Avanzados, Miguel de Cervantes 120, 31109 Chihuahua, (Mexico); Rodriguez P, A. [World Wildlife Fund (WWF), Chihuahuan Desert Program, Coronado 1005, 31000 Chihuahua (Mexico); Manjon C, G.; Garcia T, R. [Universidad de Sevilla, Departamento de Fisica Aplicada 11, ETS Arquitectura, Av. Reina Mercedes 2, 41012 Sevilla, (Spain); Crespo, T. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Av. Complutense 22, 28040 Madrid, (Spain)]. e-mail: elena.montero@cimav.edu.mx

2007-07-01

As part of a scientific research project about alpha radioactivity in groundwater for human consumption at the Chihuahua City, the characterization of rock sources of radioactivity around de Chihuahua valley was developed. The radioactivity of groundwater and sediments was determined, too. The radioactivity of uranium- and thorium- series isotopes contained in rocks was obtained by high resolution gamma-ray spectroscopy. Some representative values are 50 Bq/kg for the mean value of Bi-214 activity, and 121.5 Bq/kg for the highest value at West of the city. The activity of sediments, extracted during wells perforation, was determined using a Nal(TI) detector. A non-reported before uranium ore was localized at the San Marcos range formation. Its outcrops are inside the Chihuahua-Sacramento valley basin and its activity characterization was performed. Unusually high specific uranium activities, determined by alpha spectrometry, were obtained in water, plants, sediments and fish extracted at locations close to outcrops of uranium minerals. The activity of water of the San Marcos dam reached 7.7 Bq/L. The activity of fish, trapped at San Marcos dam, is 0.99 Bq/kg. Conclusions about the contamination of groundwater at North of Chihuahua City were obtained. (Author)

Characterization of source rocks and groundwater radioactivity at the Chihuahua valley

International Nuclear Information System (INIS)

Renteria V, M.; Montero C, M.E.; Reyes C, M.; Herrera P, E.F.; Valenzuela H, M.; Rodriguez P, A.; Manjon C, G.; Garcia T, R.; Crespo, T.

2007-01-01

As part of a scientific research project about alpha radioactivity in groundwater for human consumption at the Chihuahua City, the characterization of rock sources of radioactivity around de Chihuahua valley was developed. The radioactivity of groundwater and sediments was determined, too. The radioactivity of uranium- and thorium- series isotopes contained in rocks was obtained by high resolution gamma-ray spectroscopy. Some representative values are 50 Bq/kg for the mean value of Bi-214 activity, and 121.5 Bq/kg for the highest value at West of the city. The activity of sediments, extracted during wells perforation, was determined using a Nal(TI) detector. A non-reported before uranium ore was localized at the San Marcos range formation. Its outcrops are inside the Chihuahua-Sacramento valley basin and its activity characterization was performed. Unusually high specific uranium activities, determined by alpha spectrometry, were obtained in water, plants, sediments and fish extracted at locations close to outcrops of uranium minerals. The activity of water of the San Marcos dam reached 7.7 Bq/L. The activity of fish, trapped at San Marcos dam, is 0.99 Bq/kg. Conclusions about the contamination of groundwater at North of Chihuahua City were obtained. (Author)

Petroleum marketing monthly, June 1994

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. The feature article is entitled ``The Second Oxygenated Gasoline Season.`` 7 figs., 50 tabs.

Metals distribution in Kumkol deposit petroleum; Raspredelenie metallov v nefti Kumkol`skogo mestorozhdeniya

Energy Technology Data Exchange (ETDEWEB)

Musaeva, Z G; Nadirov, A N; Ajdarbaev, A S

1997-11-04

Metals content in samples of Kumkol deposit petroleum is determined by the method of X-ray diffraction and neutron activation analysis. Specific consideration was devoted to nickel and vanadium. It is possible, that sources of these metals are various petroleum formation as well as both the absorbed or the got in stratum microelements. (author) 10 refs., 1 tab. Suppl. Neft` i gaz Kazakhstana

Investigations of some rock stress measuring techniques and the stress field in Norway

Energy Technology Data Exchange (ETDEWEB)

Hanssen, Tor Harald

1998-12-31

Rock stresses are important to the safe construction and operation of all man-made structures in rock, whether In mining, civil or petroleum engineering. The crucial issue is their relative magnitude and orientation. This thesis develops equipment and methods for further rock stress assessment and reevaluates existing overcoring rock stress measurements, and relates this information to the present geological setting. Both laboratory work and field work are involved. In the field, rock stresses are measured by the overcoring and the hydraulic fracturing technique. An observation technique for assessing likely high stresses is developed. The field data refer to several hydropower projects and to some offshore hydrocarbon fields. The principal sections are: (1) Tectonic setting in the western Fennoscandia, (2) Triaxial rock stress measurements by overcoring using the NTH cell (a strain gauge cell developed at the Norwegian technical university in Trondheim and based on the CSIR cell of the South African Council for Scientific and Industrial Research), (3) Laboratory testing of the NTH cell, (4) Quality ranking of stresses measured by the NTH cell, (4) Recalculated rock stresses and implications to the regional stress field, (5) Hydraulic fracturing stress measurements. 113 refs., 98 figs., 62 tabs.

Investigations of some rock stress measuring techniques and the stress field in Norway

Energy Technology Data Exchange (ETDEWEB)

Hanssen, Tor Harald

1997-12-31

Rock stresses are important to the safe construction and operation of all man-made structures in rock, whether In mining, civil or petroleum engineering. The crucial issue is their relative magnitude and orientation. This thesis develops equipment and methods for further rock stress assessment and reevaluates existing overcoring rock stress measurements, and relates this information to the present geological setting. Both laboratory work and field work are involved. In the field, rock stresses are measured by the overcoring and the hydraulic fracturing technique. An observation technique for assessing likely high stresses is developed. The field data refer to several hydropower projects and to some offshore hydrocarbon fields. The principal sections are: (1) Tectonic setting in the western Fennoscandia, (2) Triaxial rock stress measurements by overcoring using the NTH cell (a strain gauge cell developed at the Norwegian technical university in Trondheim and based on the CSIR cell of the South African Council for Scientific and Industrial Research), (3) Laboratory testing of the NTH cell, (4) Quality ranking of stresses measured by the NTH cell, (4) Recalculated rock stresses and implications to the regional stress field, (5) Hydraulic fracturing stress measurements. 113 refs., 98 figs., 62 tabs.

Petroleum hydrocarbon concentrations in eight mollusc species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Sudhakar, S; Raja, P; Rajeswari, V

2011-01-01

Eight mollusc species and sediment samples collected from three different stations along Tamilnadu coast, Bay of Bengal, India were analysed for the levels of petroleum hydrocarbons to elucidate the status of the petroleum residues in mollusc meant for human consumption. The concentrations of petroleum hydrocarbons in sediments along Tamilnadu coast varied from 5.04-25.5 microg/g dw (dry weight). High concentration of petroleum hydrocarbons in the sediment of Uppanar estuary (25.5 +/- 1.45 microg/g dw) was perhaps land and marine based anthropogenic sources of this region. The petroleum hydrocarbon residues in eight mollusc species collected from Uppanar, Vellar and Coleroon estuaries varied between 2.44-6.04 microg/g ww (wet weight). Although the concentration of petroleum hydrocarbons in sediment of the Uppanar region was markedly higher than the background, the petroleum hydrocarbon residues in mollusc collected from Uppanar estuary did not suggest bioaccumulation. The results signified that industrial growth has affected the aquatic environments and regular monitoring will help to adopt stringent pollution control measures for better management of the aquatic region.

Statistical handbook for Canada's upstream petroleum industry : technical report

International Nuclear Information System (INIS)

2008-01-01

This document is an up-to-date reference source that summarizes the progress of Canada's petroleum industry. It includes detailed statistical data from 2006 and 2007 in one publication. The handbook features a compilation of key data on major economic sectors of the petroleum industry. It includes real-time drilling, reserves, and production data for crude oil and natural gas along with expenditures by province, revenues, prices, demand, consumption, refining, transportation, imports, and exports. Ethane production was also summarized along with electricity generation capacity in Canada and the status of oil, gas and product pipelines. tabs

Facts 2002. The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

The petroleum sector is highly significant for the Norwegian economy. Its share of gross domestic product, exports and total government revenues has been substantial over the past two decades, reaching a particularly high level in 2000 and 2001. The principal reason why revenues were so high in these two years is a combination of high oil prices, a strong USD against the NOK and historically high petroleum production. The share of petroleum investment in total capital spending in the Norwegian economy was at its highest in the early 1990s. Total investment in the petroleum sector has been above NOK 40 bn every year since 1992, and peaked in 1998 at roughly NOK 80 bn. Capital spending declined to around NOK 56.9 bn in 2001. The government's most important revenue sources in recent years have been cash flow from the state's direct financial interest (SDFI) and from taxes. Production of crude oil has averaged around three mill barrels per day since 1996. The figure for 2001 was 3.1 mill barrels. Including natural gas liquids (NGL) and condensate raises the 2001 average to 3.4 mill barrels oe per day. At 53 mill scm oe, gas production was also high in 2001. Oil production is expected to remain more or less unchanged over the next few years, and then to go into a gradual decline. Gas output, on the other hand, should expand substantially over the coming decade and is expected to be increasingly significant in Norwegian petroleum output in future. The petroleum sector is also a substantial player internationally. Norway ranks as the world's sixth largest producer and third largest net exporter of oil. It is also the world's third largest exporter of pipeline gas, and Norwegian foreign sales of this commodity accounted for about two per cent of global consumption in 2001. Roughly 10 per cent of west European gas consumption is covered from Norway. Several changes were made to state participation in the petroleum sector during 2001. The government sold 15 per cent of the

Facts 2002. The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

The petroleum sector is highly significant for the Norwegian economy. Its share of gross domestic product, exports and total government revenues has been substantial over the past two decades, reaching a particularly high level in 2000 and 2001. The principal reason why revenues were so high in these two years is a combination of high oil prices, a strong USD against the NOK and historically high petroleum production. The share of petroleum investment in total capital spending in the Norwegian economy was at its highest in the early 1990s. Total investment in the petroleum sector has been above NOK 40 bn every year since 1992, and peaked in 1998 at roughly NOK 80 bn. Capital spending declined to around NOK 56.9 bn in 2001. The government's most important revenue sources in recent years have been cash flow from the state's direct financial interest (SDFI) and from taxes. Production of crude oil has averaged around three mill barrels per day since 1996. The figure for 2001 was 3.1 mill barrels. Including natural gas liquids (NGL) and condensate raises the 2001 average to 3.4 mill barrels oe per day. At 53 mill scm oe, gas production was also high in 2001. Oil production is expected to remain more or less unchanged over the next few years, and then to go into a gradual decline. Gas output, on the other hand, should expand substantially over the coming decade and is expected to be increasingly significant in Norwegian petroleum output in future. The petroleum sector is also a substantial player internationally. Norway ranks as the world's sixth largest producer and third largest net exporter of oil. It is also the world's third largest exporter of pipeline gas, and Norwegian foreign sales of this commodity accounted for about two per cent of global consumption in 2001. Roughly 10 per cent of west European gas consumption is covered from Norway. Several changes were made to state participation in the petroleum sector during 2001. The government sold

Facts 2002. The Norwegian petroleum sector

International Nuclear Information System (INIS)

2002-01-01

The petroleum sector is highly significant for the Norwegian economy. Its share of gross (domestic product, exports and total government revenues has been substantial over the past two decades, reaching a particularly high level in 2000 and 2001. The principal reason why revenues were so high in these two years is a combination of high oil prices, a strong USD against the NOK and historically high petroleum production. The share of petroleum investment in total capital spending in the Norwegian economy was at its highest in the early 1990s. Total investment in the petroleum sector has been above NOK 40 bn every year since 1992, and peaked in 1998 at roughly NOK 80 bn. Capital spending declined to around NOK 56.9 bn in 2001. The government's most important revenue sources in recent years have been cash flow from the state's direct financial interest (SDFI) and from taxes. Production of crude oil has averaged around three mill barrels per day since 1996. The figure for 2001 was 3.1 mill barrels. Including natural gas liquids (NGL) and condensate raises the 2001 average to 3.4 mill barrels oe per day. At 53 mill scm oe, gas production was also high in 2001. Oil production is expected to remain more or less unchanged over the next few years, and then to go into a gradual decline. Gas output, on the other hand, should expand substantially over the coming decade and is expected to be increasingly significant in Norwegian petroleum output in future. The petroleum sector is also a substantial player internationally. Norway ranks as the world's sixth largest producer and third largest net exporter of oil. It is also the world's third largest exporter of pipeline gas, and Norwegian foreign sales of this commodity accounted for about two per cent of global consumption in 2001. Roughly 10 per cent of west European gas consumption is covered from Norway. Several changes were made to state participation in the petroleum sector during 2001. The government sold 15 per cent of the

Petroleum and Health Care: Evaluating and Managing Health Care's Vulnerability to Petroleum Supply Shifts

Science.gov (United States)

Bednarz, Daniel; Bae, Jaeyong; Pierce, Jessica

2011-01-01

Petroleum is used widely in health care—primarily as a transport fuel and feedstock for pharmaceuticals, plastics, and medical supplies—and few substitutes for it are available. This dependence theoretically makes health care vulnerable to petroleum supply shifts, but this vulnerability has not been empirically assessed. We quantify key aspects of petroleum use in health care and explore historical associations between petroleum supply shocks and health care prices. These analyses confirm that petroleum products are intrinsic to modern health care and that petroleum supply shifts can affect health care prices. In anticipation of future supply contractions lasting longer than previous shifts and potentially disrupting health care delivery, we propose an adaptive management approach and outline its application to the example of emergency medical services. PMID:21778473

Source rock evaluation and organic geochemistry of Belayim Marine Oil Field, Gulf of Suez, Egypt

Directory of Open Access Journals (Sweden)

Mohamed Abu Al-Atta

2014-09-01

In general, TOC analyses showed that the Nubia-A and B formation sediments are fairly immature compared to good source rocks with very high Hydrogen Index indicative of kerogen type II. The geochemical investigations of two oil samples indicate that the Upper Rudeis oil of Belayim Marine was derived from a marine carbonate rich source, which is relatively rich in algal organic matter and has moderate sulfur content. The maturity of the analyzed oils (about 0.75% R0 falls short from the stage of peak hydrocarbon generation which is known to be reached at about 0.85% R0.

Petroleum and ethics

International Nuclear Information System (INIS)

Henn, N.; Train, E.; Chagnoux, H.; Heinzle, P.; Daubresse, M.; Bret-Rouzaut, N.; Fradin, J.

2000-01-01

7 articles in this data sheet, they concern: political stakes and stakes of the industrial petroleum sector towards ethical questions; establishment of associations attending to human and environmental questions; examples of of ethical, environmental and safety policy in an industrialized country (ExxonMobil) and in a developing country (TotalFina); synthesis of the ethical problems that the petroleum industry encounter in industrialized and developing countries; considerations on the communication stakes in petroleum companies with the general public. (O.M.)

Petroleum marketing monthly, May 1994

Energy Technology Data Exchange (ETDEWEB)

1994-05-26

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum question. Die Oelfrage

Energy Technology Data Exchange (ETDEWEB)

Mommer, B

1983-01-01

The author analyses the development of the world petroleum market and its pricing factors to the present on the basis of the theory of ground rent, in which the part played by absolute ground rent, differential rent, and free and national state property in the capitalist mode of production is determined. His investigation of economic policy traces the absorbing history of the petroleum production and policy of the United States of America, which for so long governed the world market, the development of Venezuela into a petroleum country (whose true history is here revealed for the first time), the penetration of the middle East by the international petroleum leaseholders' capital and their cartel, the formation of the OPEC, and finally the 'victory' of the lather over the petroleum combines in the international petroleum crisis of 1970-1973. The book closes with a survey at the start of the 80s and an outlook into the foreseeable future. What is really hidden behind the quarrels about prices, profit, taxes, royalties, franchise agreements, production quotas, nationalization and so forth and behind the economic, political, and even moral arguments of the parties concerned turns out to be the fight of the petroleum ground proprietors for the ground rent - but to win a victory in this fight means ultimately to face its limitations, too. Blindness to the economic and political importance of ground rent, right from the theoretical approach, also created a major cause of the false diagnoses and forecasts on the petroleum market western economic scientists were misled into, and thus of the surprise effect that came in the form of the petroleum crisis of the early 1970s.

Petroleum hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) in Hong Kong marine sediments

International Nuclear Information System (INIS)

Zheng, G.J.; Richardson, B.J.

1999-01-01

A total of 20 surficial sediment samples, obtained from Hong Kong coastal waters, were analysed for petroleum hydrocarbons (PHCs) and a suite of 15 polycyclic aromatic hydrocarbons (PAHs). The results indicate that Hong Kong coastal sediments are often seriously polluted with petroleum related hydrocarbons. This is especially so in heavily urbanised or industrialized localities, such as Kowloon Bay (Victoria Harbour), Tsing Yi North and Tolo Harbour. Petroleum hydrocarbon pollutants in marine sediments are believed to be mainly derived from the transportation of oil, shipping activities, spillages, and industrial, stormwater and waste wastewater discharge. The ratio of unresolved complex mixture (UCM) to n-alkanes, carbon preference index (CPI), and n-C 16 values indicate that the main contribution to petroleum hydrocarbon contamination is via oil and its products. Pollutant sources appear to be stable and continuing when compared with previous data. (author)

Indicators on the world petroleum markets

International Nuclear Information System (INIS)

2000-10-01

This paper presents tendencies of the petroleum industry market. It analyses the petroleum demand and supply, the prices elaboration, the petroleum market and the OPEC objective, the third petroleum crisis of the year 2000 and gives some data concerning the petroleum market. (A.L.B.)

Figures of the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

The statistic tables give informations about: Reserves and production of petroleum and natural gas, supply of crude petroleum in the Federal Republic of Germany, pipelines, tanker ships, petroleum refineries, petroleum consumption, storage and distribution, automobiles, prices, taxis and energy consumption. The data compilations are primarily given for the Federal Republic of Germany.

Isotope shifting capacity of rock

International Nuclear Information System (INIS)

Blattner, P.; Department of Scientific and Industrial Research, Lower Hutt

1980-01-01

Any oxygen isotope shifted rock volume exactly defines a past throughput of water. An expression is derived that relates the throughput of an open system to the isotope shift of reservoir rock and present-day output. The small isotope shift of Ngawha reservoir rock and the small, high delta oxygen-18 output are best accounted for by a magmatic water source

Studies on the effect of petroleum hydrocarbon on the microbial and ...

African Journals Online (AJOL)

SERVER

2007-08-20

Aug 20, 2007 ... Key words: Hydrocarbon, microbial counts, physico-chemical characteristics. INTRODUCTION. Petroleum ... carbons, whose composition also varies with the source. ... hydrocarbons into aquifers can lead to concentrations of.

Water isotopic characterization of hypersaline formation of a petroleum field Reconcavo basin, Brazil; Caracterizacao isotopica de aguas de formacao hipersalinas de um campo de petroleo da Bacia do Reconcavo, Brasil

Energy Technology Data Exchange (ETDEWEB)

Teles, Danilo Ribeiro de Sa; Azevedo, Antonio Expedito Gomes de, E-mail: danilosateles@yahoo.com.br, E-mail: expedito@ufba.br [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Inst. de Fisica. Centro de Pesquisa em Geofisica e Geologia; Santos, Christian Pereira Lopes dos, E-mail: cplsgs@gmail.com [Instituto Federal Baiano, Salvador, BA (Brazil)

2010-04-15

Formation water is the water present in reservoir rock pores, produced together with petroleum. Usually it is hyper saline with concentrations that can be higher than 250 g/l of dissolved solids. The concentration of the dissolved elements and the isotopic composition of the water and of some of the dissolved elements can be excellent tracers to study the dynamic of underground fluid flux, the mixing of distinct sources and the origin of salinization of these waters. This work reports the isotopic composition ({delta}{sup 2}H , {delta}{sup 18}O) and electrical conductivity (EC) of formation waters from 10 wells of a petroleum field of the Reconcavo Basin, looking for their evolution, interaction with the minerals and rocks and reservoir interconnection. The samples have electric conductivity ranging from 84 to 137 mS/cm, with conductivity increasing with depth of production zone. It is observed an enrichment of deuterium and oxygen-18 with the depth of production zone, probably due to water-rock interactions that were probably increased by higher temperatures of the deeper levels and longer residence times. The samples from the production zone between 1450 to 1520 m, drained by 7 of the 10 wells sampled, show a small range in isotopic composition and in electric conductivity, indicating homogeneity in this level of the reservoir. In the shallow level of 450 m the values of {delta}{sup 2}H , {delta}{sup 18}O and EC are lower, with isotopic composition similar to the oceanic water, possibly representing the original water that entered the reservoir during the sedimentation of the basin. (author)

Petroleum marketing monthly, August 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-15

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product Sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, September 1994

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum product sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Biodegradation and chemical characterization of petroleum diesel hydrocarbons in seawater at low temperatures

OpenAIRE

Bausch, Alexandre Renee

2010-01-01

Master's thesis in Environmental engineering Petroleum hydrocarbons are a major source of marine contamination. Biodegradation, which is fundamental for the natural attenuation of these hydrocarbons in nature, involves mineralization or transformation of organic compounds by autochthonous microorganism communities. Various limiting factors characteristic of the petroleum, the external environment, and the microbial community determine the fate of oil (e.g., diesel) in the marine environmen...

Dating and source determination of volcanic rocks from Khunik area (South of Birjand, South Khorasan using Rb-Sr and Sm-Nd isotopes

Directory of Open Access Journals (Sweden)

Somayeh Samiee

2016-12-01

Full Text Available The Khunik area is located in the south of Birjand, Khorasan province, in the eastern margin of Lut block. Tertiary volcanic rocks have andesite to trachy-andesite composition. Dating analyzing by Rb-Sr method on plagioclase and hornblende as well as whole-rock isochron method was performed on pyroxene-hornblende andesite rock unit. On this basis the emplacement age is Upper Paleocene (58±11 Ma. These rocks have initial 87Sr/86Sr and εNd 0.7046-0.7049 and 2.16-3.12, respectively. According to isotopic data, volcanic rocks originated from depleted mantle and have the least crust contamination while it was fractionated. Geochemically, Khunik volcanic rocks have features typical of calk-alkaline to shoshonite and are metaluminous. Enrichment in LILEs and typical negative anomalies of Nb and Ti are evidences that the volcanic rocks formed in a subduction zone and active continental margin. Modeling suggests that these rocks were derived dominantly from 1–5% partial melting of a mainly spinel garnet lherzolite mantle source that is metasomatized by slab-derived fluid.

Implicit fracture modelling in FLAC3D: Assessing the behaviour of fractured shales, carbonates and other fractured rock types

NARCIS (Netherlands)

Osinga, S.; Pizzocolo, F.; Veer, E.F. van der; Heege, J.H. ter

2016-01-01

Fractured rocks play an important role in many types of petroleum and geo-energy operations. From fractured limestone reservoirs to unconventionals, understanding the geomechanical behaviour and the dynamically coupled (dual) permeability system is paramount for optimal development of these systems.

Conditions promoting and restraining agronomic effectiveness of water-insoluble phosphate sources, in particular phosphate rock (PR): I. Indices of phosphate rock use opportunity (PRUOIS) and of phosphate rock suitability for direct use (PRSIDU)

International Nuclear Information System (INIS)

Borlan, Z.; Gavriluta, I.; Soare, M.; Stefanescu, D.; Alexandrescu, A.

2002-01-01

Several issues of phosphate rock (PR) use are discussed in this paper. Maize for green fodder (Zea mays L) and ryegrass (Lolium multiflorum Lam.) were grown in 7 kg of dry soil and in small pots of 1.25 kg dry soil capacity, respectively, on several base unsaturated soils belonging to Hapludoll and Hapludalf soil groups. The amount of phosphate rock (PR) to apply was based on experimental data considering soil adsorbed acidity (Ah), humus content (H 2 ), cation exchange capacity (T), sum of exchangeable bases (SEB) and mobile (easily soluble) phosphate content (P A L) in the soil. The factors were combined in a rock phosphate use, opportunity index of the soil (PRUOIS): PRUOIS=(A h *H 2 *100)/SEB*10 0.0245*P AL Rock phosphate suitability for direct use was evaluated by means of the rate of PR-P dissolution (PRPRS) in a 0.6% ammonium heptamolybdate in 0.01M calcium chloride solution (ppm P) and by carbonate content (%CaCO 3 ) in PR. Both of these parameters combined provided a phosphate rock suitability index for direct use (PRSIDU): PRSIDU [ppmP/min]=PRPRS*(1-0.03*CaCO 3 ) Water insoluble P sources studied were PR from Kola-Russia, Morocco, Kneifiss-Siria, El Hassa-Jordan, Gafsa- Tunisia, North-Carolina (USA), and Arad-Israel. All PRs were compared with TSP applied at the same rate of P. Neither PRUOIS or PRSIDU considered separately could satisfactorily explain the variance of PR efficiency. An index obtained by multiplicative combination of PRUOIS x PRSIDU did correlate significantly with indices on the agronomic efficiency of PR. (author)

Yugoslavian Petroleum Refinery development program

International Nuclear Information System (INIS)

Ocic, Ozren

1999-01-01

This paper shows the analysis of the world petroleum industry development, being an important factor in planning the development of the Yugoslav petroleum industry and Pancevo Petroleum Refinery, as well. Then Yugoslav petroleum industry development is analysed, including the appropriate balances of crude oil production and crude oil products consumption. The way of realizing the basic targets are also proposed. Likewise, the analysis of the condition within West European refineries has been conducted, from the aspects of technology, energy consumption and environmental protection and the same analysis for Pancevo Petroleum Refinery has been presented, too. The analysis of the condition within the refineries in the European Union countries and comparing it with the condition within Pancevo Petroleum Refinery, makes it mainly possible to recognize the development programmes which should be realized in order that Pancevo Petroleum Refinery could reach the refining level of the EU countries. (Original)

Problems of radiation safety of petroleum and gas production

International Nuclear Information System (INIS)

Garibov, A.A.

2002-01-01

Oil and gas production is the basis of economy of the Azerbaijan Republic and its cause in ecological and radioecology problems. One form this problem is the pollution by radionuclides of environment at the time of gas and petroleum production. At the time of petroleum and gas production the three-phase radionuclides are emitted in atmosphere: Emissions consisted from solid U-238, Ra-226, Th-232, K-40 discharged to atmosphere at the time of production, exploring and exploitation of petroleum and gas. They are presented in compounds of sand, clay, and petroleum residues; During the drilling and production the gross quantities of water flows out and collects. These water areas consist of radium, uranium, Th and K-40 dissolved in water salts; There are the radionuclides being in 902 condition emitted in atmosphere at the places of petroleum and gas production. The radon and its isotopes are emitted at this time; At the places of petroleum and gas production it is observed at local pollution areas polluted by solid emissions that at this territories the doze of exposition power variable 100 - 1000 micro/hour. The radioactivity at this system according to 2-1000 year/k consists from Ra, K-40, and U. At this areas the value of total background changes 5 - 1000 micro R/hour. The total radioactivity of water polls formed at the places of petroleum and gas production consisted 50 -150 Bq/L. In the case of gas the separated radionuclides are mainly consisted from Radon and its isotopes. In the compound of produced gas the concentration of radon varied 20 - 1700 Bq/m 3 . Thus, at the places of petroleum and gas production radioactive pollutants emitted to atmosphere, forms the polluted environment for working and living people at the same territory. This problem's status haven't been investigated thoroughly, the sources of pollution hasn't been uncovered concretely, the cleaning technology for polluted areas is unknown

Applications of T-ray spectroscopy in the petroleum field

Science.gov (United States)

Al-Douseri, Fatemah M.

2005-11-01

Because of heavy usage of petroleum products, which are the main source of energy in daily life and industry, a fast, reliable, and portable analysis system is needed to complement traditional techniques. Terahertz (THz) radiation, or T-rays, is electromagnetic radiation in the 0.1 to 10 THz frequency range. One unique attribute of T-rays is their ability to sensitively measure the induced molecular dipole moments in non-polar liquids such as aromatics, which make up the majority of the contents of many petroleum products. This information can lead to several applications in petroleum analysis. The application of T-rays to petroleum product analysis has the potential to make a significant impact in the petroleum field. In this dissertation, I show the first use of T-ray time-domain spectroscopy and Fourier transform infrared (FTIR) spectroscopy techniques for petroleum product analysis. I report on the feasibility of analyzing selected petroleum products, including gasoline, diesel, lubricating oil, and selected compounds of toluene, ethylbenzene, and xylene (BTEX). With the use of a T-ray time-domain spectrometer. I demonstrate that gasolines with different octane numbers and diesel all show specific absorption coefficients and refractive indexes in the spectral range from 0.5 to 2.0 THz. Furthermore, I report the qualitative and quantitative analysis of selected BTEX components in gasoline and diesel using FTIR spectroscopy in the 50 to 650 cm-1 region. I distinguish gasolines with different octane numbers from diesel and lubricating oil according to their different spectral features. I also determine the concentration of (o, m, p) xylene isomers in gasoline according to their specific absorption bands. The experimental results in this thesis, imply that linking between the knowledge of petroleum products and the development of T-ray spectrometer with the cooperation of industry might translate the T-ray spectroscopic system into a real world application in

Facts 2010 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Thermal Maturity Data Used by the U.S. Geological Survey for the U.S. Gulf Coast Region Oil and Gas Assessment

Science.gov (United States)

Dennen, Kristin O.; Warwick, Peter D.; McDade, Elizabeth Chinn

2010-01-01

The U.S. Geological Survey is currently assessing the oil and natural gas resources of the U.S. Gulf of Mexico region using a total petroleum system approach. An essential part of this geologically based method is evaluating the effectiveness of potential source rocks in the petroleum system. The purpose of this report is to make available to the public RockEval and vitrinite reflectance data from more than 1,900 samples of Mesozoic and Tertiary rock core and coal samples in the Gulf of Mexico area in a format that facilitates inclusion into a geographic information system. These data provide parameters by which the thermal maturity, type, and richness of potential sources of oil and gas in this region can be evaluated.

Petroleum resources assessment (I)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

On the basis of diverse microfossils such as foraminifers, ostracods, micromulluscs, fossil spores and pollen and calcareous nannofossils derived from 14 drill holes, the sediments are divided into two part, the upper marine part and the lower nonmarine one. Marine part is subdivided into 4 foraminiferal zones and 3 nannofossil zones of Plio-Pleistocene age. In the lower part ranging from Oligocene to Late Miocene 4 palynomoph assemblages are established, which reflect climatic changes fluctuating between subtropical and cool temperate. Some fine sediments occurring in the South Sea continental shelf are rich in organic matter to be hydrocarbon source rock. The organic matter is mainly compared to type 3. However, lower part of the Geobuk-1 and Okdom-1 shows more oil prone geochemical characteristics than other wells. The kerosene is mixture type 1 and type 3 organic matter. The main oil generation zone located between 2,500 m and 3,000 m and gas generation zone from 3,500 m to 4,000 m approximately. Hydrocarbon accumulation could be expected in the trap formed in the period earlier than 10 Ma. as the hydrocarbon started to be expelled at 10 Ma. according to the modeling. Approximately 13,000 Line-km of multichannel seismic data integrated with 14 wells and gravity and magnetic data were analyzed to investigate the structural and stratigraphic evolution of southern part of offshore Korea. The northeast-southwest trending Taiwan-Sinzi Uplift Belt separates the area into two regions with different tectonic features, northwestern and southwestern regions. The potential hydrocarbon traps associated with anticline, tilted fault block, fault, unconformity, and rollover structure exist. This project is consisted of two main subjects. 1) Petroleum resources assessment on the continental shelf basin of the south sea. 2) Petroliferous basin analysis in Taegu area (1). (author). refs., tabs., figs.

Identification of refined petroleum products in contaminated soils using an identification index for GC chromatograms.

Science.gov (United States)

Kwon, Dongwook; Ko, Myoung-Soo; Yang, Jung-Seok; Kwon, Man Jae; Lee, Seung-Woo; Lee, Seunghak

2015-08-01

Hydrocarbons found in the environment are typically characterized by gas chromatography (GC). The shape of the GC chromatogram has been used to identify the source of petroleum contamination. However, the conventional practice of simply comparing the peak patterns of source products to those of environmental samples is dependent on the subjective decisions of individual analysts. We have developed and verified a quantitative analytical method for interpreting GC chromatograms to distinguish refined petroleum products in contaminated soils. We found that chromatograms for gasoline, kerosene, and diesel could be divided into three ranges with boundaries at C6, C8, C16, and C26. In addition, the relative peak area (RPA(GC)) of each range, a dimensionless ratio of the peak area within each range to that of the total range (C6-C26), had a unique value for each petroleum product. An identification index for GC chromatograms (ID(GC)), defined as the ratio of RPA(GC) of C8-C16 to that of C16-C26, was able to identify diesel and kerosene sources in samples extracted from artificially contaminated soils even after weathering. Thus, the ID(GC) can be used to effectively distinguish between refined petroleum products in contaminated soils.

Petroleum refining and air quality

International Nuclear Information System (INIS)

Raimbault, C.

1992-01-01

This paper studies the methods which may be developed in petroleum refineries or during petroleum products using for air pollution abatement: petroleum products desulfurization, lead elimination in gasoline and catalytic converters to reduce sulfur dioxide and nitrogen oxides in exhaust gases. Investments and costs estimation to adapt petroleum refineries for environment protection is also given. 1 ref., 6 figs., 6 tabs

Facts 2011 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2011-07-15

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Facts 2010 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

2005 yearly days of petroleum

International Nuclear Information System (INIS)

Constant, R.; Susbielles, G.

2005-01-01

14 articles are gathered in this data sheet; they deal with the opening address of the 2005 petroleum days; the hydrocarbons: the evolutive resource; the para-petroleum engineers and the Europe; the speech of Mr Francois Loos; the Shell global scenarios to 2025; the evolution of the gas resource and its uses; the French para-petroleum industry; Bernard Bensaid, Corinne Sagary, Armelle Saniere, economic studies, IFP; the contribution of the innovation and of the technology in the diversification of the hydrocarbons supply; innovation and diversification of the petroleum resource: the point of view of Total; research, development and diversification of the petroleum resource; innovation in services companies; innovation in study and development and engineering; the closing address of the 2005 petroleum days. (O.M.)

Proceedings of the 2004 annual petroleum days

International Nuclear Information System (INIS)

Millet, M.

2004-01-01

The 2004 annual petroleum days were organized by the AFTP, the CEPM and the GEP. The main theme, entitled 'hydrocarbons, energies of the future and environment' was dealing with the depletion of the petroleum resources and the necessity to reduce the greenhouse gases emissions (industrial facilities and transportation systems). The leaders of French companies (IFP, CGG, BP France, Total) explained their point of view during the plenary sessions, while during the parallel sessions, several experts presented the works in progress in the different branches of the petroleum industry. This article summarizes these different talks and treats of the following topics: the evolution of the global oil production and the abatement of air pollution, the evolution of exploration-production investments and the evolution of oil prices, the evaluation of reserves and their reevaluation, the global warming and the fight against the greenhouse effect (air pollution abatement, development of renewable energy sources, increase of energy efficiency, CO 2 sequestration etc..), evolution of transportation systems (hydrogen fuel cell, biomass fuels, hybrid electric-powered vehicles). A summary of the specialized sessions about new techniques concludes the article: improvements in stratigraphy, seismic surveys, and well logging. (J.S.)

EIA model documentation: Petroleum Market Model of the National Energy Modeling System

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-30

The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. Documentation of the model is in accordance with EIA`s legal obligation to provide adequate documentation in support of its models (Public Law 94-385, section 57.b.2). The PMM models petroleum refining activities, the marketing of products, the production of natural gas liquids and domestic methanol, projects petroleum provides and sources of supplies for meeting demand. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption.

Unzen volcanic rocks as heat source of geothermal activity

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Masao; Sugiyama, Hiromi

1987-03-25

Only a few radiometric ages have been reported so far for the Unzen volcanic rocks. In this connection, in order to clarify the relation between volcanism and geothermal activity, fission track ages of zircon seperated from the Unzen volcanic rocks in western Kyushu have been dated. Since all the rocks are thought to be young, the external surface re-etch method was adopted. The results are that the age and standard error of the basal volcaniclastic rocks of the Tatsuishi formation are 0.28 +- 0.05 Ma and 0.25 +- 0.05 Ma. The next oldest Takadake lavas range from 0.26 to 0.20 Ma. The Kusenbudake lavas fall in a narrow range from 0.19 to 0.17 Ma. The latest Fugendake lavas are younger than 0.07 Ma.In conclusion, the most promising site for geothermal power generation is the Unzen hot spring field because of its very high temperature. After that, comes the Obama hot spring field because of the considerable high temperature chemically estimated. In addition, the northwestern area of the Unzen volcanic region will be promising for electric power generation in spite of no geothermal manifestations, since its volcanos are younger than 0.2 Ma. (14 figs, 14 tabs, 22 refs)

Bio-paraffins: alternative products to petroleum paraffins; Bioparafinas: produtos alternativos as parafinas de petroleo

Energy Technology Data Exchange (ETDEWEB)

Lima, Anie Daniela Medeiros [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES). Gerencia de Hidrorrefino e Processos Especiais; Oliveira, Claudia Cristina Cardoso Calvano de; Carvalho, Ivone de Freitas; Silva, Danilo do Carmo Santos; Cruz, Valeria Senra da Silva [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES). Gerencia de Lubrificantes e Produtos Especiais]. E-mails: anie.lima, claudiacristina, ivone, danilosilva, vsenra@petrobras.com.br

2007-04-15

Market trends and social and environmental issues encouraged the vegetal wax presence in the world-wide paraffin market. This work presents the most commercialized vegetal waxes, soy and pal, comparing their physicochemical characteristics and their applicability with the paraffins obtained from petroleum. It also presents a characterization of the carnauba wax, produced exclusively in Brazil and a comparison with paraffins from petroleum. The carnauba wax is an alternative product, with good applicability as a substitute for waxes from petroleum or a petroleum/vegetal mixture. The characteristics of palm and soy waxes show the possible application in candles, cosmetics, foods and others industries. Brazil, having a great agricultural potential, represents a source of vegetal wax that could be use to meet the market demands. (author)

Logistics aspects of petroleum pipeline operations

Directory of Open Access Journals (Sweden)

W. J. Pienaar

2010-11-01

Full Text Available The paper identifies, assesses and describes the logistics aspects of the commercial operation of petroleum pipelines. The nature of petroleum-product supply chains, in which pipelines play a role, is outlined and the types of petroleum pipeline systems are described. An outline is presented of the nature of the logistics activities of petroleum pipeline operations. The reasons for the cost efficiency of petroleum pipeline operations are given. The relative modal service effectiveness of petroleum pipeline transport, based on the most pertinent service performance measures, is offered. The segments in the petroleum-products supply chain where pipelines can play an efficient and effective role are identified.

Geology and assessment of the undiscovered, technically recoverable petroleum resources of Armenia, 2013

Science.gov (United States)

Klett, T.R.

2016-02-23

The U.S. Geological Survey (USGS) assessed the undiscovered, technically recoverable oil and gas resources of Armenia in 2013. A Paleozoic and a Cenozoic total petroleum system (TPS) were identified within the country of Armenia. The postulated petroleum system elements are uncertain, resulting in low geologic probabilities for significant oil an gas resources. Two assessment units (AU) were delineated in each TPS—a Paleozoic-Sourced Conventional Reservoirs AU and a Permian Shale Gas AU in the Paleozoic Composite TPS and a Paleogene-Sourced Conventional Reservoirs AU and a Cenozoic Coalbed Gas AU in the Cenozoic Composite TPS. The TPS elements are largely uncertain and risked, and so only the Paleogene-Sourced Conventional Reservoirs AU was quantitatively assessed because the geologic probability is more than the threshold of 10 percent (that is, the probability of at least one conventional oil or gas accumulation of 5 million barrels of oil equivalent or greater based on postulated petroleum-system elements). The USGS estimated fully risked mean volumes of about 1 million barrels of oil (MMBO), about 6 billion cubic feet of natural gas (BCFG), and less than 1 million barrels of natural gas liquids (MMBNGL).

Impact of Acid Attack on the Shear Behaviour of a Carbonate Rock Joint

Science.gov (United States)

Nouailletas, O.; Perlot, C.; Rivard, P.; Ballivy, G.; La Borderie, C.

2017-06-01

The mechanical behaviour of structural discontinuities in rock mass is a key element of the stability analysis in civil engineering, petroleum engineering and mining engineering. In this paper, the mechanical analysis is coupled with the acidic attack of a rock joint associated with leakage of CO2 through a geological fault in the context of carbon sequestration. Experiments were conducted at the laboratory scale to assess the shear behaviour of degraded joint: direct shear tests were performed on rock joints that have been previously immersed into water or into an acidic solution (pH 0.2). The shear behaviour of joints is governed by the roughness of its walls: the parameters Z2, Z3, Z4 and RL characterize the rough surfaces. They are calculated from the scans of joint surfaces after and before immersion. Their comparison pointed out a slight impact of the acidic attack. However, the results of the direct shear tests show significant modifications in the shear behaviour for the degraded joints: the tangential stress peak disappears, the tangential stiffness decreases in the stress/displacement curve, and the contraction increases, the dilation angle decreases in the dilation curve. Acid attack has a greater impact on the mechanical properties of the asperities than their geometric characteristics. The results of this study will be used to improve chemo-mechanical modelling to better simulate with higher accuracy the fault stability in different cases of civil engineering, petroleum engineering and mining engineering.

Migrated hydrocarbons in outcrop samples: revised petroleum exploration directions in the Tarim Basin

Energy Technology Data Exchange (ETDEWEB)

Li, Maowen; Snowdon, Lloyd [Geological Survey of Canada, Calgary, AB (Canada); Xiao, Zhongyao [CNPC Tarim Petroleum Exploration Bureau, Kuerle, Xinjiang (China); Lin, Renzi [Petroleum Univ., Changping, Beijing (China); Wang, Peirong; Hou, Dujie [Jianghan Petroleum Univ., Hubei (China); Zhang, Linye [SINOPEC Shengli Petroleum Bureau, Dongying, Shandong (China); Zhang, Shuichang; Liang, Digang [Research Inst. of Petroleum Exploration and Development, Beijing (China)

2000-07-01

The application of age-specific biomarker distributions established from mature exploration areas of the Tarim Basin, northwestern China, indicates that most Carboniferous-Permian outcrop samples in the eastern segment of the Southwest Depression, previously believed to have significant petroleum source potential, in fact contain migrated hydrocarbons derived from Cambrian-Lower Ordovician strata. New geochemical results have led to a major revision of petroleum exploration directions in this area. (Author)

Microbial dynamics in petroleum oilfields and their relationship with physiological properties of petroleum oil reservoirs.

Science.gov (United States)

Varjani, Sunita J; Gnansounou, Edgard

2017-12-01

Petroleum is produced by thermal decay of buried organic material over millions of years. Petroleum oilfield ecosystems represent resource of reduced carbon which favours microbial growth. Therefore, it is obvious that many microorganisms have adapted to harsh environmental conditions of these ecosystems specifically temperature, oxygen availability and pressure. Knowledge of microorganisms present in ecosystems of petroleum oil reservoirs; their physiological and biological properties help in successful exploration of petroleum. Understanding microbiology of petroleum oilfield(s) can be used to enhance oil recovery, as microorganisms in oil reservoirs produce various metabolites viz. gases, acids, solvents, biopolymers and biosurfactants. The aim of this review is to discuss characteristics of petroleum oil reservoirs. This review also provides an updated literature on microbial ecology of these extreme ecosystems including microbial origin as well as various types of microorganisms such as methanogens; iron, nitrate and sulphate reducing bacteria, and fermentative microbes present in petroleum oilfield ecosystems. Copyright © 2017 Elsevier Ltd. All rights reserved.

The world petroleum industry

International Nuclear Information System (INIS)

Mons, L.

2005-01-01

This study proposes a global vision of the petroleum industry, a precise and well argued state of the art of the petroleum markets. It defines the strategical challenges which the petroleum companies are exposed and allows to anticipate the sector evolutions. It details the key acts of the last three years, the financial performances of the companies. (A.L.B.)

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

International Nuclear Information System (INIS)

Xiong Yongqiang; Wang Yanmei; Wang Yongquan; Xu Shiping

2007-01-01

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition

Compound-specific C- and H-isotope compositions of enclosed organic matter in carbonate rocks: Implications for source identification of sedimentary organic matter and paleoenvironmental reconstruction

Energy Technology Data Exchange (ETDEWEB)

Xiong Yongqiang [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)], E-mail: xiongyq@gig.ac.cn; Wang Yanmei; Wang Yongquan; Xu Shiping [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2007-11-15

The Bohai Bay Basin is one of the most important oil-producing provinces in China. Molecular organic geochemical characteristics of Lower Paleozoic source rocks in this area have been investigated by analyzing chemical and isotopic compositions of solvent extracts and acid-released organic matter from the Lower Paleozoic carbonate rocks in the Jiyang Sub-basin of the Bohai Bay Basin. The results indicate that enclosed organic matter in carbonate rocks has not been recognizably altered by post-depositional processes. Two end-member compositions are suggested for early organic matter trapped in the Lower Paleozoic carbonate rocks: (1) a source dominated by aquatic organisms and deposited in a relatively deep marine environment and (2) a relatively high saline, evaporative marine depositional environment. In contrast, chemical and isotopic compositions of solvent extracts from these Lower Paleozoic carbonate rocks are relatively complicated, not only inheriting original characteristics of their precursors, but also overprinted by various post-depositional alterations, such as thermal maturation, biodegradation and mixing. Therefore, the integration of both organic matter characteristics can provide more useful information on the origin of organic matter present in carbonate rocks and the environments of their deposition.

Molecular isotopic characterisation of hydrocarbon biomarkers in Palaeocene-Eocene evaporitic, lacustrine source rocks from the Jianghan Basin, China

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Grice, Kliti; Schouten, S.; Peters, Kenneth E.

1998-01-01

Immature organic matter in lacustrine source rocks from the Jianghan Basin, eastern China, was studied for distributions and stable carbon isotopic compositions (13C) of hydrocarbon biomarkers. All of the bitumens contain isorenieratane (13C ca. −17 ) indicating the presence of Chlorobiaceae, and

The north-east Baffin Bay region, offshore Greenland - a new frontier petroleum exploration region

Energy Technology Data Exchange (ETDEWEB)

Gregersen, U. (Geological Survey of Denmark and Greenland, Copenhagen (Denmark))

2008-07-15

In recent years the Arctic has come into focus for hydrocarbon exploration, and areas offshore both West and East Greenland have been evaluated as promising frontier hydrocarbon provinces. Seven hydrocarbon exploration and exploitation licenses were awarded in 2007-2008 offshore the Disko-Nuussuaq region, and two more have been awarded in the open-door region offshore south-western Greenland. In 2007, an extensive amount of new seismic and aero-magnetic data was acquired by the TGS-NOPEC Geophysical Company in the north-eastern Baffin Bay region. Geophysical mapping has been initiated by the Geological Survey of Denmark and Greenland (GEUS) in the Melville Bugt region offshore North-West Greenland with the purpose of evaluating the hydrocarbon prospectivity. Initial interpretation of seismic and gravity data suggests the presence of deep sedimentary basins separated by structural highs. Geological information on source rock, reservoir rock and seal intervals from surrounding regions suggest that the Melville Bugt region is likely to have a significant petroleum potential. The study is based on public domain magnetic and gravity data, and all proprietary and public 2-D seismic data acquired before 2003. Seismic horizons from the 'seismic basement' to 'base Quaternary' are being interpreted regionally. Based on the seismic interpretation, a structural element map, depth-structure maps and isopach maps will be produced in order to assess the prospectivity of the Melville Bugt region. (au)

Sources And Compositional Distribution Of Polycyclic Aromatic ...

African Journals Online (AJOL)

For molecular mass 178, an anthracene to anthracene plus phenanthrene ratio ≤ 0.10 was taken as indication of petroleum related sources, while a ratio > 0.10 indicated dominance of combustion related sources. For molecular mass 202, a fluoranthene to fluoranthene plus pyrene ratio ≤ 0.50 was indication of petroleum ...

Geology and total petroleum systems of the Gulf of Guinea province of West Africa

Science.gov (United States)

Brownfield, Michael E.; Charpentier, Ronald R.

2006-01-01

The Gulf of Guinea Province as defined by the U.S. Geological Survey (USGS) consists of the coastal and offshore areas of Cote d'Ivoire, Ghana, Togo, and Benin, and the western part of the coast of Nigeria, from the Liberian border east to the west edge of the Niger Delta. The province includes the Ivory Coast, Tano, Central, Saltpond, Keta, and Benin Basins and the Dahomey Embayment. The area has had relatively little hydrocarbon exploration since 1968, with only 33 small to moderate-sized oil and gas fields having been discovered prior to the USGS assessment. Most discoveries to 1995 have been located in water depths less than 500 m. Since 1995, only eight new offshore discoveries have been made, with four of the discoveries in the deep-water area of the province. Although as many as five total petroleum systems exist in the Gulf of Guinea Province, only one, the Cretaceous Composite Total Petroleum System, and its assessment unit, the Coastal Plain and Offshore Assessment Unit, had sufficient data to allow assessment. The province shows two important differences compared to the passive-margin basins south of the Niger Delta: (1) the influence of transform tectonics, and (2) the absence of evaporites and salt deformation. The province also lacks long-lived, large deltaic systems that typically result in rapid source rock burial and abundant high-quality hydrocarbon reservoirs. The USGS assessed the potential for undiscovered conventional oil and gas resources in the Gulf of Guinea Province as part of its World Petroleum Assessment 2000, estimating a mean of 1,004 million barrels of conventional undiscovered oil, 10,071 billion cubic feet of gas, and 282 million barrels of natural gas liquids. Most of the hydrocarbon potential is postulated to be in the offshore, deeper waters of the province. Gas resources may be large, as well as accessible, in areas where the zone of hydrocarbon generation is relatively shallow.

Sedimentary basin analysis and petroleum potential of the Cretaceous and Tertiary strata in Korea.

Energy Technology Data Exchange (ETDEWEB)

Son, Jin-Dam; Kwak, Young-Hoon; Bong, Pil-Yoon [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

1999-12-01

Since 1992 sedimentary basin analysis to assess petroleum potential of the Cretaceous and Tertiary strata in the Korean onshore and continental shelf have been carried out. The Cretaceous non-marine strata mainly occupy the Gyeongsang Basin in southeastern part of the Korean Peninsula and small basins such as Haenam and Gyeokpo depressions in western coastal areas. The Tertiary strata are mostly distributed in Domi, Cheju, Socotra subbasins, and Okinawa Trough in the South Continental Shelf, and Kunsan and Heuksan basins in the West. The basin evolution and petroleum potential for each basins are characterized as follow. The Cretaceous Gyeongsang sediments were deposited in three subbasins including Milyang, Euisung and Yongyang subbasins. The black shales in Nakdong and Jinju formations are interpreted to contain abundant organic matter during the deposition, thermal maturity reaching up to the zone of dry gas formation. Because porosity and permeability are too low, the sandstones can act as a tight gas reservoir rather than conventional oil and gas reservoir. The latest Cretaceous strata of Haenam and Kyeokpo depressions in western coastal area are correlated into the Yuchon Volcanic Group of the Gyeongsang Basin. Petroleum potential of the Early Cretaceous basin in the West Continental Shelf could be relatively high in terms of sedimentary basin filled with thick lacustrine sediments. The Kunsan basin in the West Continental Shelf originated in the Early Cretaceous time expanded during the Paleocene time followed by regional erosion at the end of Paleocene on which Neogene sediment have been accumulated. The Paleocene-Eocene sublacustrine shales may play an major role as a source and cap rocks. South Continental Shelf Basin is subdivided by Cheju subbasin in the center, Socotra Subbasin to the west, Domi Subbasin to the northeast and Okinawa Trough to the East. The potential hydrocarbon traps associated with anticline, titled fault blocks, fault, unconformity

Energy and more in '84

International Nuclear Information System (INIS)

Anon.

1984-01-01

This book contains 116 abstracts from papers presented at a Utah meeting of the American Association of Petroleum Geologists. The abstracts are published in alphabetical order by author's name, but were presented at the meeting under the following categories: structure of the basin and range province and its margin; stratigraphy of Paleozoic rocks; uranium and tar sands; structure of the Rocky Mountain Thrust Belt; source rock symposium; stratigraphy of Mesozoic-Cenozoic rocks; coal; coal and alternate energy; foreland basins and structures; oil and gas fields; sedimentation and depositional environments - marine/marginal marine/terrestrial; and petroleum activities and concepts of exploration

Risk management guidelines for petroleum storage tank sites

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-10-01

These guidelines provide a site management process designed particularly for soil and groundwater pollution originating from existing or former petroleum storage tank (PST) facilities and provide uniform standards for the remediation of polluted PST sites in Alberta. The numerical criteria, risk management objectives and technical information described in this document were compiled from four documents including Remediation Guidelines for Petroleum Storage Tank Sites 1994, the Canada-Wide Standards for Petroleum Hydrocarbons in Soil, Alberta Soil and Water Quality Guidelines for Hydrocarbons at Upstream Oil and Gas Facilities, and Guidelines for Managing Risks at Contaminated Sites in Alberta. The changes in these updated guidelines reflect new remediation criteria and provide a process for determining alternate site-specific management objectives for more petroleum storage tank sites. The guidelines were developed using a risk-based approach that ensures the protection of human health, safety and the environment. The guidelines apply to aboveground and underground storage tank facilities that contain gasoline, diesel, heating oil, and aviation fuel. The guidelines specify requirements by Alberta Environment and the Alberta Fire Code. The chapter on risk management process included information on site investigation, determination of soil type, pollution source removal, land use assessment, selection of exposure pathways, depth of remediation, human inhalation and groundwater protection pathways, and verification of remediation. figs, 4 tabs., 2 appendices.

Origin of a Tertiary oil from El Mahafir wildcat & geochemical correlation to some Muglad source rocks, Muglad basin, Sudan

Science.gov (United States)

Fadul Abul Gebbayin, Omer. I. M.; Zhong, Ningning; Ali Ibrahim, Gulfan; Ali Alzain, Mohamed

2018-01-01

Source rock screening analysis was performed on four stratigraphic units from the Muglad basin namely; Abu Gabra, Zarqa, Ghazal, and Baraka formations using pyrolysis and Vitrinite Reflectance (Ro). Results, integrated with the chromatographic and isotopic data from these rocks extracts and a Tertiary oil from El Mahafir-1 wild cat, were used to determine the origin of the oil. A good organic source within the Middle Abu Gabra Formation is observed in wells El Toor-6 and Neem Deep-1 (TOC, 1.0-2.0% & S2 5.0-10.0 mg C/g rock), with mixed kerogens I, II, & III, and thermally mature (% Ro = 0.74-0.94). The Campanian-Early Maastrichtian sequence, i.e. Zarqa and Ghazal formations are generally poor (TOC, diversity, both in space and time and is characterized by dominant algal input at some areas and or stratigraphic intervals [Elevated tricyclics, higher C29/C30 hopanes (0.5-1.14), and relatively low Gammacerane indices (4.6-14.4)], while mixed with abundant terrigenous material at others. A direct correlation between El Mahafir oil and the Abu Gabra extracts is thus inferred based on: its mixed organic source nature, oxic to sub-oxic depositional environment (Pr/Ph 1.22), relatively low C29/C30 hopanes (0.54), low C28 steranes (29%), and a high gammacerane index (20.5). This is largely supported by the maturity modeling results which suggest generation is only from the Abu Gabra at this location.

A review of modern instrumental methods of elemental analysis of petroleum related material. Part 2

International Nuclear Information System (INIS)

Nadkarni, R.A.

1991-01-01

In this paper a review is presented of the state of the art in elemental analysis of petroleum-related materials (crude oil, gasoline, additives, and lubricants) using modern instrumental analysis techniques. The major instrumental techniques used for elemental analysis of petroleum products include atomic absorption spectrometry (both with flame and with graphite furnace atomizer), inductively coupled plasma atomic emission spectrometry, ion chromatography, microelemental methods, neutron activation, spark source mass spectrometry, and x-ray fluorescence. Each of these techniques is compared for its advantages, disadvantages, and typical applications in the petroleum field

Organic maturation levels, thermal history and hydrocarbon source rock potential of the Namurian rocks of the Clare Basin, Ireland

Energy Technology Data Exchange (ETDEWEB)

Goodhue, Robbie; Clayton, Geoffrey [Trinity Coll., Dept. of Geology, Dublin (Ireland)

1999-11-01

Vitrinite reflectance data from two inland cored boreholes confirm high maturation levels throughout the onshore part of the Irish Clare Basin and suggest erosion of 2 to 4 km of late Carboniferous cover and elevated palaeogeothermal gradients in the Carboniferous section. The observed maturation gradients are fully consistent with the published hypothesis of a late Carboniferous/Permian 'superplume' beneath Pangaea but local vertical reversals in gradients also suggest a complex thermal regime probably involving advective heating. The uppermost Visean--lower Namurian Clare Shale is laterally extensive and up to 300 m thick. Although this unit is post-mature, TOC values of up to 15% suggest that it could have considerable hydrocarbon source rock potential in any less mature offshore parts of the basin. (Author)

Ex-USSR: petroleum activities in 1991

International Nuclear Information System (INIS)

1992-01-01

This paper gives statistical data on economy and petroleum industry in ex-USSR: Primary energy production and consumption (coal, petroleum, natural gas, primary power), petroleum and natural gas reserves, drilling activity, exports and imports of petroleum products, refining capacity. 2 figs., 14 tabs

Mechanical study of the Chartreuse Fold-and-Thrust Belt: relationships between fluids overpressure and decollement within the Toarcian source-rock

Science.gov (United States)

Berthelon, Josselin; Sassi, William; Burov, Evgueni

2016-04-01

Many source-rocks are shale and constitute potential detachment levels in Fold-and-Thrust Belts (FTB): the toarcian Schistes-Cartons in the French Chartreuse FTB for example. Their mechanical properties can change during their burial and thermal maturation, as for example when large amount of hydrocarbon fluids are generated. A structural reconstruction of the Chartreuse FTB geo-history places the Toarcian Formation as the major decollement horizon. In this work, a mechanical analysis integrating the fluids overpressuring development is proposed to discuss on the validity of the structural interpretation. At first, an analogue of the Chartreuse Toarcian Fm, the albanian Posidonia Schist, is documented as it can provide insights on its initial properties and composition of its kerogen content. Laboratory characterisation documents the vertical evolution of the mineralogical, geochemical and mechanical parameters of this potential decollement layer. These physical parameters (i.e. Total Organic Carbon (TOC), porosity/permeability relationship, friction coefficient) are used to address overpressure buildup in the frontal part of the Chartreuse FTB with TEMISFlow Arctem Basin modelling approach (Faille et al, 2014) and the structural emplacement of the Chartreuse thrust units using the FLAMAR thermo-mechanical model (Burov et al, 2014). The hydro-mechanical modeling results highlight the calendar, distribution and magnitude of the overpressure that developed within the source-rock in the footwall of a simple fault-bend fold structure localized in the frontal part of the Chartreuse FTB. Several key geological conditions are required to create an overpressure able to fracture the shale-rocks and induce a significant change in the rheological behaviour: high TOC, low permeability, favourable structural evolution. These models highlight the importance of modeling the impact of a diffuse natural hydraulic fracturing to explain fluids propagation toward the foreland within

Petroleum, alcohol, and energy substitution in Brazil: Theoretical and empirical issues

International Nuclear Information System (INIS)

Biller, D.

1991-01-01

As in other Latin American nations, the petroleum industry has always been surrounded by controversy in Brazil. Issues related to exploration, exploitation, and import of crude have received special attention by Brazilian decision makers. In the past decade, an additional relevant issue was brought into play by the oil crisis. An import substitution program for energy was implemented by the development of alternative indigenous energy sources. Among these sources, sugarcane was viewed as a reliable renewable resource for the production of fuel alcohol and, very recently, of electricity. Brazil engaged in a gigantic program of fuel substitution, which is now facing severe problems due to the fall of petroleum prices. This study analyzes the recent energy import substitution program in Brazil, specifically concentrating on microeconomic and environmental aspects of fuel substitution

Iron speciation and mineral characterization of upper Jurassic reservoir rocks in the Minhe Basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiangxian; Zheng, Guodong, E-mail: gdzhbj@mail.iggcas.ac.cn; Xu, Wang [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Liang, Minliang [Chinese Academy of Geological Sciences, Institute of Geomechanics, Key Lab of Shale Oil and Gas Geological Survey (China); Fan, Qiaohui; Wu, Yingzhong; Ye, Conglin [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Shozugawa, Katsumi; Matsuo, Motoyuki [The University of Tokyo, Graduate School of Arts and Sciences (Japan)

2016-12-15

Six samples from a natural outcrop of reservoir rocks with oil seepage and two control samples from surrounding area in the Minhe Basin, northwestern China were selectively collected and analyzed for mineralogical composition as well as iron speciation using X-ray powder diffraction (XRD) and Mössbauer spectroscopy, respectively. Iron species revealed that: (1) the oil-bearing reservoir rocks were changed by water-rock-oil interactions; (2) even in the same site, there was a different performance between sandstone and mudstone during the oil and gas infusion to the reservoirs; and (3) this was evidence indicating the selective channels of hydrocarbon migration. In addition, these studies showed that the iron speciation by Mössbauer spectroscopy could be useful for the study of oil and gas reservoirs, especially the processes of the water-rock interactions within petroleum reservoirs.

The hidden face of the petroleum

International Nuclear Information System (INIS)

Laurent, E.

2006-02-01

For the first time, a book reveals what that was hidden to the public opinions: why the petroleum crisis of 1973 what only a manipulation, an arrangement between the OPEC and the petroleum companies, why the data concerning the petroleum reserves are wrong and increased by the producers countries, how Washington used the Saudi petroleum weapon to create the Soviet Union fall, and why from march 2001 maps of the Iraq (where were drawn the future petroleum explorations) were working documents for the vice President Cheney and petroleum managers for the ''secret society''. (A.L.B.)

Canadian petroleum industry: 1988 monitoring report. First six months

International Nuclear Information System (INIS)

1988-01-01

The Petroleum Monitoring Agency was established in 1980 to provide the federal government with comprehensive and objective information on and analysis of the financial performance of the petroleum industry in Canada. The Agency publishes a semi-annual and an annual report based on information received directly from all but the smallest oil and gas companies. Data published are mainly aggregate data derived from survey schedules prescribed by regulations. This report presents a summary and highlights of the activities of the first half of 1988. Information is presented on corporate mergers and acquisitions; financial performance by sector (upstream, downstream, foreign) and total operations as seen by net income and cash flow; sources and uses of funds; a comparative performance by the petroleum and other industries as seen by net income and capital expenditures; ownership and control trends; international flows of funds; capital structures; and data related to income taxes. New features added in this report include expansion of the table representing the financial performance and profit margins of the refining/marketing segment to incorporate net income as a component of the analysis; analysis of the industry's use of exploration and investment tax credits; and a chart showing Canadian crude oil acquisition costs vs petroleum product prices. 12 figs., 63 tabs

A novel molecular index for secondary oil migration distance.

Science.gov (United States)

Zhang, Liuping; Li, Maowen; Wang, Yang; Yin, Qing-Zhu; Zhang, Wenzheng

2013-01-01

Determining oil migration distances from source rocks to reservoirs can greatly help in the search for new petroleum accumulations. Concentrations and ratios of polar organic compounds are known to change due to preferential sorption of these compounds in migrating oils onto immobile mineral surfaces. However, these compounds cannot be directly used as proxies for oil migration distances because of the influence of source variability. Here we show that for each source facies, the ratio of the concentration of a select polar organic compound to its initial concentration at a reference point is independent of source variability and correlates solely with migration distance from source rock to reservoir. Case studies serve to demonstrate that this new index provides a valid solution for determining source-reservoir distance and could lead to many applications in fundamental and applied petroleum geoscience studies.

Petroleum industry in CIS

International Nuclear Information System (INIS)

Vaillaud, P.

1992-01-01

This paper gives statistical data on petroleum and natural gas industry in USSR and in Eastern Europe: crude oil and gas production, petroleum and natural gas deposits, exports, fuel consumption, pipelines network (total length, compressor or pump stations), petroleum refineries. This paper describes also air pollution (carbon dioxide and sulfur dioxide) and Environmental effects of coal and lignite using in fossil power plants in Eastern Europe. 17 figs., 7 tabs

Marks on the petroleum fiscality

International Nuclear Information System (INIS)

2007-02-01

This document offers some marks on the petroleum fiscality in France: the taxes as the 'accises' and the 'TVA', the part of the taxes in the sale price at the service station, the comparison with other countries of Europe, the tax revenues and the Government budget. It provides also marks on the fuels prices formation (margins), the world petroleum markets (supply and demand) and the part of the petroleum companies on the petroleum market. (A.L.B.)

Apparatus for extracting petroleum

Energy Technology Data Exchange (ETDEWEB)

Coogan, J

1921-01-18

An apparatus for extracting petroleum from petroleum bearing sand or shale is described comprising a container for liquids, the container being divided into a plurality of compartments, an agitator mounted within the container and below the liquid level and having its forward end opening into one of the compartments, means for delivering sand or shale to the forward end of the agitator, means for subjecting the sand or shale to the action of a solvent for the petroleum while the sand or shale is being agitated and is submerged, the first-mentioned compartment being adapted to receive the extracted petroleum and means for removing the treated sand or shale from adjacent the rear end of the agitator.

Fundamentals of Petroleum.

Science.gov (United States)

Bureau of Naval Personnel, Washington, DC.

Basic information on petroleum is presented in this book prepared for naval logistics officers. Petroleum in national defense is discussed in connection with consumption statistics, productive capacity, world's resources, and steps in logistics. Chemical and geological analyses are made in efforts to familiarize methods of refining, measuring,…

REE enrichment in granite-derived regolith deposits of the southeast United States: Prospective source rocks and accumulation processes

Science.gov (United States)

Foley, Nora K.; Ayuso, Robert A.; Simandl, G.J.; Neetz, M.

2015-01-01

The Southeastern United States contains numerous anorogenic, or A-type, granites, which constitute promising source rocks for REE-enriched ion adsorption clay deposits due to their inherently high concentrations of REE. These granites have undergone a long history of chemical weathering, resulting in thick granite-derived regoliths, akin to those of South China, which supply virtually all heavy REE and Y, and a significant portion of light REE to global markets. Detailed comparisons of granite regolith profiles formed on the Stewartsville and Striped Rock plutons, and the Robertson River batholith (Virginia) indicate that REE are mobile and can attain grades comparable to those of deposits currently mined in China. A REE-enriched parent, either A-type or I-type (highly fractionated igneous type) granite, is thought to be critical for generating the high concentrations of REE in regolith profiles. One prominent feature we recognize in many granites and mineralized regoliths is the tetrad behaviour displayed in REE chondrite-normalized patterns. Tetrad patterns in granite and regolith result from processes that promote the redistribution, enrichment, and fractionation of REE, such as late- to post- magmatic alteration of granite and silicate hydrolysis in the regolith. Thus, REE patterns showing tetrad effects may be a key for discriminating highly prospective source rocks and regoliths with potential for REE ion adsorption clay deposits.

Place of petroleum in the U. K. fuel market. [In relation to electricity, gas, and coal

Energy Technology Data Exchange (ETDEWEB)

Nicolaou, G B

1977-06-01

An attempt is made to study the interaction process that occurs between petroleum products and the remainder of the fuel market. Petroleum competes with electricity, gas, and coal as a source of fuel, and an assessment is made of the demand elasticities of its place in the fuel market. In the U.K. fuel market the question is to what extent petroleum is a substitute or complement to the others. Petroleum consumption constituted 25 percent in 1960 of the total fuel consumption and has grown constantly since. The extent to which it changes depends upon its close substitutes. Which out of gas, coal, and electricity is, in fact, the closest substitute for petroleum; is it sensitive to price or to other things. In order to attempt to answer these questions, two models are presented. The first presents a straightforward linear equation for the demand for petroleum due to a change in total fuel consumption. This is then used in Model 2, which is basically the Slutsky equation, to obtain the mean substitution effect between petroleum and coal, gas and electricity. This, then, measures the net substitution or complementarity between petroleum and the commodities mentioned. 11 references.

Canadian petroleum history bibliography

Energy Technology Data Exchange (ETDEWEB)

Cass, D.

2003-09-27

The Petroleum History Bibliography includes a list of more than 2,000 publications that record the history of the Canadian petroleum industry. The list includes books, theses, films, audio tapes, published articles, company histories, biographies, autobiographies, fiction, poetry, humour, and an author index. It was created over a period of several years to help with projects at the Petroleum History Society. It is an ongoing piece of work, and as such, invites comments and additions.

Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

Science.gov (United States)

Hackley, Paul C.; Sanfilipo, John

2016-01-01

Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro  1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2α-methylhopane for photosynthetic cyanobacteria implies shallow photic zone deposition of Madr marls and 3β-methylhopane indicates presence of methanotrophic archaea in the microbial consortium. The data presented herein are consistent with deposition of Suzak bituminous marls in shallow stratified waters of a restricted marine basin associated with the southeastern incipient or proto-Paratethys. Geochemical proxies from Suzak rock extracts (S content, high polar content, C isotopes, normal (αααR) C27–29 steranes, and C29/C30 and C26/C25 hopane ratios) are similar to extant data from Paleogene oils produced to the north in the Afghan-Tajik Basin. This observation may indicate laterally equivalent strata are effective source rocks as suggested by previous workers; however, further work is needed to strengthen oil-source correlations.

Boom times : Canada's crude petroleum industry : analysis in brief

International Nuclear Information System (INIS)

Rowat, M.R.

2006-01-01

This document examined the trends in crude oil prices, the production and exports of Canada's crude petroleum industry, and Canada's imports of crude petroleum. As an exporter and importer of crude oil, Canada's petroleum industry is currently experiencing economic prosperity as a result of high oil prices combined with high global demand for oil. This document reviewed industry activity for 2005 and addressed the reasons for the first decline in Canadian crude oil production in 6 years. A quick review of soaring crude oil prices, supply and shortages was also presented. A review of exports revealed that since 1995, the United States has received 99 per cent of Canadian exports. Although production activity is occurring in 7 provinces, the biggest participant is Alberta, followed by Saskatchewan. In 2005, Canada produced 136.4 million cubic metres of crude petroleum, of which two-thirds came from Alberta. Saskatchewan contributed 18 per cent of total Canadian crude oil production, while offshore oil rigs in Newfoundland and Labrador contributed 13 per cent. The vast oil sands resource accounted for 42 per cent of the province's total production. Alberta oil export is piped entirely into the United States. In 2005, even with a slight drop in exports, Canadian oil exporters received $30 billion for their products, up from $25 billion the year before. Canada also supplied nearly 10 per cent of the American crude oil needs. According to the National Energy Board, Canadian refineries are approaching capacity. Canada's 19 refineries, which have a capacity of 320,000 cubic metres per day, operated at 92 per cent of capacity in 2005 to meet the needs of the domestic market. More imported petroleum was refined than Canadian sourced petroleum. In 2005, the gas and oil industry saw historically high profits, taxes paid and investments. 6 refs., 5 figs

Petroleum marketing monthly, March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-10

This report for March 1995, provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly. A glossary is included.

Effects of explosions in hard rocks

International Nuclear Information System (INIS)

Heuze, F.E.; Walton, O.R.; Maddix, D.M.; Shaffer, R.J.; Butkovich, T.R.

1993-01-01

This work relates to explosions in hard rocks (ex: basalt, granite, limestone...). Hard rock masses typically have a blocky structure created by the existence of geologic discontinuities such as bedding contacts, faults, and joints. At very high pressure - hundreds of kilobars and above - these discontinuities do not act separately, and the rock appears to be an equivalent continuous medium. At stress of a few tens of kilobars and below, the geologic discontinuities control the kinematics of the rock masses. Hence, the simulation of rock dynamics, anywhere but in the very-near source region, should account for those kinematics

75 FR 74457 - Mandatory Reporting of Greenhouse Gases: Petroleum and Natural Gas Systems

Science.gov (United States)