Flow in porous media, phase behavior and ultralow interfacial tensions: mechanisms of enhanced petroleum recovery. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Davis, H.T.; Scriven, L.E.

1982-01-01

A major program of university research, longer-ranged and more fundamental in approach than industrial research, into basic mechanisms of enhancing petroleum recovery and into underlying physics, chemistry, geology, applied mathematics, computation, and engineering science has been built at Minnesota. The 1982 outputs of the interdisciplinary team of investigators were again ideas, instruments, techniques, data, understanding and skilled people: forty-one scientific and engineering papers in leading journals; four pioneering Ph.D. theses; numerous presentations to scientific and technical meetings, and to industrial, governmental and university laboratories; vigorous program of research visits to and from Minnesota; and two outstanding Ph.D.'s to research positions in the petroleum industry, one to a university faculty position, one to research leadership in a governmental institute. This report summarizes the 1982 papers and theses and features sixteen major accomplishments of the program during that year. Abstracts of all forty-five publications in the permanent literature are appended. Further details of information transfer and personnel exchange with industrial, governmental and university laboratories appear in 1982 Quarterly Reports available from the Department of Energy and are not reproduced here. The Minnesota program continues in 1983, notwithstanding earlier uncertainty about the DOE funding which finally materialized and is the bulk of support. Supplemental grants-in-aid from nine companies in the petroleum industry are important, as are the limited University and departmental contributions. 839 references, 172 figures, 29 tables.

40 CFR 1065.720 - Liquefied petroleum gas.

Science.gov (United States)

2010-07-01

... may use fuel that your in-use engines normally use, such as commercial-quality liquefied petroleum gas... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Liquefied petroleum gas. 1065.720... CONTROLS ENGINE-TESTING PROCEDURES Engine Fluids, Test Fuels, Analytical Gases and Other Calibration...

New engineers for the natural gas and petroleum industry; Nachwuchs fuer die Erdgas-/Erdoelindustrie

Energy Technology Data Exchange (ETDEWEB)

Reinicke, K.M.; Pusch, G. [TU Clausthal (Germany). Inst. fuer Erdoel- und Erdgastechnik

2007-09-13

Tne natural gas and petroleum industry needs engineers. Universities are faced with the challenge of training them and ensuring their technical, communicative and personal skills. Universities are taking new strategies to do this, joining efforts with other universities and with the oil and natural gas industry. New media are employed, increasingly also for advanced training and for learning by correspondence course in order to provide students with special knowledge and facilitate career changes. The paper describes implemented and projected studies in petroleum and natural gas technology at TU Clausthal university and joint projects with partner universities and industry. (orig.)

Modeling a distributed environment for a petroleum reservoir engineering application with software product line

International Nuclear Information System (INIS)

Scheidt, Rafael de Faria; Vilain, Patrícia; Dantas, M A R

2014-01-01

Petroleum reservoir engineering is a complex and interesting field that requires large amount of computational facilities to achieve successful results. Usually, software environments for this field are developed without taking care out of possible interactions and extensibilities required by reservoir engineers. In this paper, we present a research work which it is characterized by the design and implementation based on a software product line model for a real distributed reservoir engineering environment. Experimental results indicate successfully the utilization of this approach for the design of distributed software architecture. In addition, all components from the proposal provided greater visibility of the organization and processes for the reservoir engineers

Modeling a distributed environment for a petroleum reservoir engineering application with software product line

Science.gov (United States)

de Faria Scheidt, Rafael; Vilain, Patrícia; Dantas, M. A. R.

2014-10-01

Petroleum reservoir engineering is a complex and interesting field that requires large amount of computational facilities to achieve successful results. Usually, software environments for this field are developed without taking care out of possible interactions and extensibilities required by reservoir engineers. In this paper, we present a research work which it is characterized by the design and implementation based on a software product line model for a real distributed reservoir engineering environment. Experimental results indicate successfully the utilization of this approach for the design of distributed software architecture. In addition, all components from the proposal provided greater visibility of the organization and processes for the reservoir engineers.

Recycling used palm oil and used engine oil to produce white bio oil, bio petroleum diesel and heavy fuel

Science.gov (United States)

Al-abbas, Mustafa Hamid; Ibrahim, Wan Aini Wan; Sanagi, Mohd. Marsin

2012-09-01

Recycling waste materials produced in our daily life is considered as an additional resource of a wide range of materials and it conserves the environment. Used engine oil and used cooking oil are two oils disposed off in large quantities as a by-product of our daily life. This study aims at providing white bio oil, bio petroleum diesel and heavy fuel from the disposed oils. Toxic organic materials suspected to be present in the used engine oil were separated using vacuum column chromatography to reduce the time needed for the separation process and to avoid solvent usage. The compounds separated were detected by gas chromatography-mass spectrometry (GC-MS) and found to contain toxic aromatic carboxylic acids. Used cooking oils (thermally cracked from usage) were collected and separated by vacuum column chromatography. White bio oil produced was examined by GC-MS. The white bio oil consists of non-toxic hydrocarbons and is found to be a good alternative to white mineral oil which is significantly used in food industry, cosmetics and drugs with the risk of containing polycyclic aromatic compounds which are carcinogenic and toxic. Different portions of the used cooking oil and used engine were mixed to produce several blends for use as heavy oil fuels. White bio oil was used to produce bio petroleum diesel by blending it with petroleum diesel and kerosene. The bio petroleum diesel produced passed the PETRONAS flash point and viscosity specification test. The heat of combustion of the two blends of heavy fuel produced was measured and one of the blends was burned to demonstrate its burning ability. Higher heat of combustion was obtained from the blend containing greater proportion of used engine oil. This study has provided a successful recycled alternative for white bio oil, bio petroleum fuel and diesel which can be an energy source.

Mechanical engineer's handbook

CERN Document Server

Marghitu, Dan B

2001-01-01

The Mechanical Engineer's Handbook was developed and written specifically to fill a need for mechanical engineers and mechanical engineering students throughout the world. With over 1000 pages, 550 illustrations, and 26 tables the Mechanical Engineer's Handbook is very comprehensive, yet affordable, compact, and durable. The Handbook covers all major areas of mechanical engineering with succinct coverage of the definitions, formulas, examples, theory, proofs, and explanations of all principle subject areas. The Handbook is an essential, practical companion for all mechanic

Combustion characteristics of a turbocharged DI compression ignition engine fueled wth petroleum diesel fuels and biodiesel

Energy Technology Data Exchange (ETDEWEB)

Canakci, M. [Kocaeli University, Izmit (Turkey). Department of Mechanical Education

2007-04-15

In this study, the combustion characteristics and emissions of two different petroleum diesel fuels (No. 1 and No. 2) and biodiesel from soybean oil were compared. The tests were performed at steady state conditions in a four-cylinder turbocharged DI diesel engine at full load at 1400-rpm engine speed. The experimental results compared with No. 2 diesel fuel showed that biodiesel provided significant reductions in PM, CO, and unburned HC, the NO{sub x} increased by 11.2%. Biodiesel had a 13.8% increase in brake-specific fuel consumption due to its lower heating value. However, using No. 1 diesel fuel gave better emission results, NO{sub x} and brake-specific fuel consumption reduced by 16.1% and 1.2%, respectively. The values of the principal combustion characteristics of the biodiesel were obtained between two petroleum diesel fuels. The results indicated that biodiesel may be blended with No. 1 diesel fuel to be used without any modification on the engine. (author)

Mechanical engineering education

CERN Document Server

Davim, J Paulo

2012-01-01

Mechanical Engineering is defined nowadays as a discipline "which involves the application of principles of physics, design, manufacturing and maintenance of mechanical systems". Recently, mechanical engineering has also focused on some cutting-edge subjects such as nanomechanics and nanotechnology, mechatronics and robotics, computational mechanics, biomechanics, alternative energies, as well as aspects related to sustainable mechanical engineering.This book covers mechanical engineering higher education with a particular emphasis on quality assurance and the improvement of academic

Experimental analysis on a spark ignition petrol engine fuelled with LPG (liquefied petroleum gas)

International Nuclear Information System (INIS)

Masi, Massimo

2012-01-01

The use of LPG (liquefied petroleum gas) as alternative fuel to petrol is common practise in spark ignition engines. While the main driving force to the use of LPG still remains the low cost for the end user, its favourable pollutant emissions, in particular carbon dioxide, will in the middle term probably increase interest in LPG as an IC engine fuel. In addition, there are both theoretical and technical reasons to consider LPG as an attractive fuel also in terms of engine performance. Despite the continuously increasing stock production of dual-fuel (petrol–LPG) passenger car models, doubts still exist about both real engine performance in LPG operation and the reliability of the dual-fuel feeding system. This paper deals with the theoretical advantages of using LPG as fuel for SI engines. Brake performance tests of a passenger car engine fed with petrol and LPG are analysed and compared. The stock engine has been equipped with a “third-generation” standard kit for dual-fuel operation. The performance reductions in LPG operation are discussed in both steady state and transient condition. The results of some modifications to the set-up of both the petrol and LPG metering devices, designed for a better justification of the measured performance, are also presented. -- Highlights: ► Experimental research on the actual performances of an SI engine fed with petrol and gaseous LPG. ► Theoretical advantages and drawbacks of fuelling SI ICE’s with LPG. ► Brake performance analysis shows a noticeable gap between LPG and petrol operation. ► Local measurements confirm that the thermodynamic operation of the evaporator-pressure reducer device is crucial for the engine performance. ► The performance of the up-to-date kit for petrol–LPG dual-fuel operation is greatly affected by the settings of the mechanical components of the LPG evaporator device.

Tokamak engineering mechanics

International Nuclear Information System (INIS)

Song, Yuntao; Wu, Weiyue; Du, Shijun

2014-01-01

Provides a systematic introduction to tokamaks in engineering mechanics. Includes design guides based on full mechanical analysis, which makes it possible to accurately predict load capacity and temperature increases. Presents comprehensive information on important design factors involving materials. Covers the latest advances in and up-to-date references on tokamak devices. Numerous examples reinforce the understanding of concepts and provide procedures for design. Tokamak Engineering Mechanics offers concise and thorough coverage of engineering mechanics theory and application for tokamaks, and the material is reinforced by numerous examples. Chapter topics include general principles, static mechanics, dynamic mechanics, thermal fluid mechanics and multiphysics structural mechanics of tokamak structure analysis. The theoretical principle of the design and the methods of the analysis for various components and load conditions are presented, while the latest engineering technologies are also introduced. The book will provide readers involved in the study of mechanical/fusion engineering with a general understanding of tokamak engineering mechanics.

Engineering mechanics

CERN Document Server

Gross, Dietmar; Schröder, Jörg; Wall, Wolfgang A; Rajapakse, Nimal

Statics is the first volume of a three-volume textbook on Engineering Mechanics. The authors, using a time-honoured straightforward and flexible approach, present the basic concepts and principles of mechanics in the clearest and simplest form possible to advanced undergraduate engineering students of various disciplines and different educational backgrounds. An important objective of this book is to develop problem solving skills in a systematic manner. Another aim of this volume is to provide engineering students as well as practising engineers with a solid foundation to help them bridge the gap between undergraduate studies on the one hand and advanced courses on mechanics and/or practical engineering problems on the other. The book contains numerous examples, along with their complete solutions. Emphasis is placed upon student participation in problem solving. The contents of the book correspond to the topics normally covered in courses on basic engineering mechanics at universities and colleges. Now in i...

Tokamak engineering mechanics

CERN Document Server

Song, Yuntao; Du, Shijun

2013-01-01

Tokamak Engineering Mechanics offers concise and thorough coverage of engineering mechanics theory and application for tokamaks, and the material is reinforced by numerous examples. Chapter topics include general principles, static mechanics, dynamic mechanics, thermal fluid mechanics and multiphysics structural mechanics of tokamak structure analysis. The theoretical principle of the design and the methods of the analysis for various components and load conditions are presented, while the latest engineering technologies are also introduced. The book will provide readers involved in the study

Corrosion in systems for storage and transportation of petroleum products and biofuels identification, monitoring and solutions

CERN Document Server

Groysman, Alec

2014-01-01

This book treats corrosion as it occurs and affects processes in real-world situations, and thus points the way to practical solutions. Topics described include the conditions in which petroleum products are corrosive to metals; corrosion mechanisms of petroleum products; which parts of storage tanks containing crude oils and petroleum products undergo corrosion; dependence of corrosion in tanks on type of petroleum products; aggressiveness of petroleum products to polymeric material; how microorganisms take part in corrosion of tanks and pipes containing petroleum products; which corrosion monitoring methods are used in systems for storage and transportation of petroleum products; what corrosion control measures should be chosen; how to choose coatings for inner and outer surfaces of tanks containing petroleum products; and how different additives (oxygenates, aromatic solvents) to petroleum products and biofuels influence metallic and polymeric materials. The book is of interest to corrosion engineers, mat...

COBEM 99: Proceedings of the 15. Brazilian congress on mechanical engineering

International Nuclear Information System (INIS)

1999-01-01

The Brazilian Congress on Mechanical Engineering is the main event promoted by the Brazilian Society of Mechanical Sciences and happens biannually. In the congress people involved in industrial, research and teaching activities are able to meet and discuss or present, in technical sessions and exhibitions, recent technological and scientific contributions to this area and related activities. The 15. edition of the COBEM, due to 99, took place in Aguas de Lindoia, Sao Paulo State. Theoretical and experimental papers are presented approaching the following area and subjects: petroleum industry, equipment and products, gas and wind turbines, hydroelectric power plants and equipment, environmental subjects, computerized analysis, heat transfer, fluid flow, thermal machines, porous media, nuclear energy, solar energy, refrigeration, energy sources, consumption and conservation

Flow in porous media, phase and ultralow interfacial tensions: Mechanisms of enhanced petroleum recovery

Energy Technology Data Exchange (ETDEWEB)

Davis, H.T.; Scriven, L.E.

1991-07-01

A major program of university research, longer-ranged and more fundamental in approach than industrial research, into basic mechanisms of enhancing petroleum recovery and into underlying physics, chemistry, geology, applied mathematics, computation, and engineering science has been built at Minnesota. The original focus was surfactant-based chemical flooding, but the approach taken was sufficiently fundamental that the research, longer-ranged than industrial efforts, has become quite multidirectional. Topics discussed are volume controlled porosimetry; fluid distribution and transport in porous media at low wetting phase saturation; molecular dynamics of fluids in ultranarrow pores; molecular dynamics and molecular theory of wetting and adsorption; new numerical methods to handle initial and boundary conditions in immiscible displacement; electron microscopy of surfactant fluid microstructure; low cost system for animating liquid crystallites viewed with polarized light; surfaces of constant mean curvature with prescribed contact angle.

Environmental science, petroleum engineer`s view. CO2 gas reduction technologies for global warming prevention; Sekiyu gijutsusha no shiten kara no kankyo kagaku. Chikyu ondanka eno taio no tame no CO{sub 2} yokusei gijutsu

Energy Technology Data Exchange (ETDEWEB)

Nomura, K [Tokyo (Japan)

1998-08-01

This paper discusses the techniques concerning diesel engines for cogeneration systems, techniques concerning fuel consumption-saving type lubricating oils and techniques concerning oil refineries, out of the CO2 emission control (energy saving) techniques for coping with the global warming which the petroleum engineers are now tackling. The paper introduces CO2 emission control techniques using a petroleum cogeneration system and studies on NOx removing techniques using catalysts as the techniques concerning diesel engines; techniques for reducing friction loss, which occurs in an engine and a transmission, by improving the recipes of lubricating oils and the development of novel friction modifiers as the fuel consumption-saving type lubricating oil techniques; and the CO2 separating techniques using a system for recovering the low-temperature waste heat produced in petroleum refinement with a high efficiency, or using a solid film such as a molecular sieve as the energy-saving techniques used in oil refineries. 18 refs., 8 figs., 1 tab.

Mechanical engineering

CERN Document Server

Darbyshire, Alan

2010-01-01

Alan Darbyshire's best-selling text book provides five-star high quality content to a potential audience of 13,000 engineering students. It explains the most popular specialist units of the Mechanical Engineering, Manufacturing Engineering and Operations & Maintenance Engineering pathways of the new 2010 BTEC National Engineering syllabus. This challenging textbook also features contributions from specialist lecturers, ensuring that no stone is left unturned.

Engineering and service activities in the Cogema group

International Nuclear Information System (INIS)

1998-03-01

This short document presents the engineering and service daughter companies of the Cogema group: SGN (nuclear engineering, fuel cycle, wastes and spent fuels management, decontamination and dismantling); Euriware group (advice, expertise and information systems in nuclear, pharmacy, petroleum, automotive and steel making industries); Game group (industrial maintenance in nuclear, chemistry, petroleum, automotive and steel making industries); Eurisys Mesures (nuclear measurements, instrumentation, radiation protection and nuclear imaging); SICN (mechanics); STMI and Socodei (nuclear cleansing and management of low level radioactive wastes); Krebs/Speichim (chemical engineering, divisions of SGN and Technip). (J.S.)

The role of the University of Calgary in the development of a centre of excellence in petroleum technology

International Nuclear Information System (INIS)

Moore, G.; Chakma, A.

1996-01-01

The role of the University of Calgary's Department of Chemical and Petroleum Engineering in developing a world centre of excellence in petroleum engineering in Calgary, was discussed. Reasons for the failure of previous efforts to establish a Department of Petroleum Engineering at the University were explained. High participation levels in the existing Department of Chemical and Petroleum Reservoir Engineering's water-flooding, and reservoir engineering programs were noted. Support for the development of a centre of excellence in petroleum engineering from government and industry, with specific reference to the the recently instituted, government sponsored, ACCESS program, was described. Problems in maintaining a University Faculty with a wide range of petroleum expertise were noted. Current plans for the development of a Conjoint Centre of Applied Petroleum Technology in conjunction with the Southern Alberta Institute of Technology were described. The joint effort between the two institutions appeared to be the most promising avenue to date to realize the dream of Calgary as a world center of excellence in petroleum engineering, preparing future workers in the petroleum industry at all levels, from technologists to post-doctoral fellows

Engineering and the Politics of Commensuration in the Mining and Petroleum Industries

Directory of Open Access Journals (Sweden)

Jessica M. Smith

2018-03-01

Full Text Available Engineers and applied scientists form the backbone of the mining and petroleum industries, yet rarely figure in social science accounts of natural resource extraction. This article begins to fill that gap by ethnographically exploring how community conflicts have prompted engineers and applied scientists working in these industries to reconsider the relationship between the surface and subsurface dimensions of their work. To make social concerns on the surface matter to how drilling and extraction would happen, they tried to make these two domains legible to one another. Using mapping and modeling, they created new techniques for making “social” concerns visible and actionable by field operators, even as they expressed reservations about unduly flattening the inherent complexity of human thought, action, and emotion in the process. While these practices opened space for other engineers and applied scientists to incorporate the concerns of nearby residents into their plans and practices, they also raised questions about the appropriateness of commensuration, or the process of translation through which things and values are made comparable.

Orbital compressed air and petroleum injury mimicking necrotizing fasciitis.

Science.gov (United States)

Mellington, Faye E; Bacon, Annette S; Abu-Bakra, Mohammed A J; Martinez-Devesa, Pablo; Norris, Jonathan H

2014-09-01

Orbital injury secondary to petroleum-based products is rare. We report the first case, to our knowledge, of a combined compressed air and chemical orbital injury, which mimicked necrotizing fasciitis. A 58-year-old man was repairing his motorcycle engine when a piston inadvertently fired, discharging compressed air and petroleum-based carburetor cleaner into his left eye. He developed surgical emphysema, skin necrosis, and a chemical cellulitis, causing an orbital compartment syndrome. He was treated initially with antibiotics and subsequently with intravenous steroid and orbital decompression surgery. There was almost complete recovery by 4 weeks postsurgery. WHY SHOULD AN EMERGENCY PHYSICIAN BE AWARE OF THIS?: Petroleum-based products can cause severe skin irritation and necrosis. Compressed air injury can cause surgical emphysema. When these two mechanisms of injury are combined, the resulting orbitopathy and skin necrosis can mimic necrotizing fasciitis and cause diagnostic confusion. A favorable outcome is achievable with aggressive timely management. Copyright © 2014 Elsevier Inc. All rights reserved.

Mechanical engineers data handbook

CERN Document Server

Carvill, James

1994-01-01

This text provides the student and professional mechanical engineer with a reference text of an essentially practical nature. It is uncluttered by text, and extensive use of illustrations and tables provide quick and clear access to information. It alsoincludes examples of detailed calculations on many of the applications of technology used by mechanical and production engineers, draughtsmen and engineering designers.Although mainly intended for those studying and practising mechanical engineering, a glance at the contents will show that it is also useful to those in related br

Mechanics of fluid flow

CERN Document Server

Basniev, Kaplan S; Chilingar, George V 0

2012-01-01

The mechanics of fluid flow is a fundamental engineering discipline explaining both natural phenomena and human-induced processes, and a thorough understanding of it is central to the operations of the oil and gas industry.  This book, written by some of the world's best-known and respected petroleum engineers, covers the concepts, theories, and applications of the mechanics of fluid flow for the veteran engineer working in the field and the student, alike.  It is a must-have for any engineer working in the oil and gas industry.

Predicting the performances of a CAMPRO engine retrofitted with liquefied petroleum gas (LPG system using 1-dimensional software

Directory of Open Access Journals (Sweden)

Kamaruddin M. Hazeem

2017-01-01

Full Text Available Recently, the depletion of petroleum resources and the impact of exhaust emission caused by combustion towards environmental has been forced to all researchers to come out with an alternative ways to prevent this situation become worse. Liquefied petroleum gas (LPG is the most compatible and have a potential to become a source of energy for internal combustion engine. Unfortunately, the investigation of LPG in internal combustion engine among researcher still have a gap in research. Thus, in this study a 1-Dimensional simulation CAMPRO 1.6L engine model using GT-Power is developed to predict the performances of engines that using LPG as a fuel for internal combustion engine. The constructed model simulation will throughout the validation process with the experimental data to make sure the precision of this model. The validation process shows that the results have a good agreement between the simulation model and the experimental data. As a result, the performance of LPG simulation model shows that a Brake Torque (BT, Brake Power (BP and Brake Mean Effective Pressure (BMEP were significantly improved in average of 7% in comparison with gasoline model. In addition, Brake Specific Fuel Consumption (BSFC also shows an improvement by 5%, which is become more economic. Therefore, the developed GT-Power model offer a successful fuel conversion to LPG systems via retrofit technology to provide comprehensive support for implementation of energy efficient and environmental friendly vehicles.

Applications of aerospace technology to petroleum extraction and reservoir engineering

Science.gov (United States)

Jaffe, L. D.; Back, L. H.; Berdahl, C. M.; Collins, E. E., Jr.; Gordon, P. G.; Houseman, J.; Humphrey, M. F.; Hsu, G. C.; Ham, J. D.; Marte, J. E.;

Springer handbook of mechanical engineering

Energy Technology Data Exchange (ETDEWEB)

Grote, Karl-Heinrich [Magdeburg Univ. (Germany). Dept. of Mechanical Engineering; Antonsson, Erik K. (eds.) [California Inst. of Technology (CALTEC), Pasadena, CA (United States). Dept. of Mechanical Engineering

2009-07-01

Mechanical Engineering is a professional engineering discipline which involves the application of principles of physics, design, manufacturing and maintenance of mechanical systems. It requires a solid understanding of the key concepts including mechanics, kinematics, thermodynamics and energy. Mechanical engineers use these principles and others in the design and analysis of automobiles, aircrafts, heating and cooling systems, industrial equipment and machinery. In addition to these main areas, specialized fields are necessary to prepare future engineers for their positions in industry, such as mechatronics and robotics, transportation and logistics, fuel technology, automotive engineering, biomechanics, vibration, optics and others. Accordingly, the Springer Handbook of Mechanical Engineering devotes its contents to all areas of interest for the practicing engineer as well as for the student at various levels and educational institutions. Authors from all over the world have contributed with their expertise and support the globally working engineer in finding a solution for today's mechanical engineering problems. Each subject is discussed in detail and supported by numerous figures and tables. DIN standards are retained throughout and ISO equivalents are given where possible. The text offers a concise but detailed and authoritative treatment of the topics with full references. (orig.)

A brief history of mechanical engineering

CERN Document Server

Dixit, Uday Shanker; Davim, J Paulo

2017-01-01

What is mechanical engineering? What a mechanical engineering does? How did the mechanical engineering change through ages? What is the future of mechanical engineering? This book answers these questions in a lucid manner. It also provides a brief chronological history of landmark events and answers questions such as: When was steam engine invented? Where was first CNC machine developed? When did the era of additive manufacturing start? When did the marriage of mechanical and electronics give birth to discipline of mechatronics? This book informs and create interest on mechanical engineering in the general public and particular in students. It also helps to sensitize the engineering fraternity about the historical aspects of engineering. At the same time, it provides a common sense knowledge of mechanical engineering in a handy manner.

Combustion and exhaust emission characteristics of a compression ignition engine using liquefied petroleum gas-Diesel blended fuel

International Nuclear Information System (INIS)

Qi, D.H.; Bian, Y.ZH.; Ma, ZH.Y.; Zhang, CH.H.; Liu, SH.Q.

2007-01-01

Towards the effort of reducing pollutant emissions, especially smoke and nitrogen oxides, from direct injection (DI) Diesel engines, engineers have proposed various solutions, one of which is the use of a gaseous fuel as a partial supplement for liquid Diesel fuel. The use of liquefied petroleum gas (LPG) as an alternative fuel is a promising solution. The potential benefits of using LPG in Diesel engines are both economical and environmental. The high auto-ignition temperature of LPG is a serious advantage since the compression ratio of conventional Diesel engines can be maintained. The present contribution describes an experimental investigation conducted on a single cylinder DI Diesel engine, which has been properly modified to operate under LPG-Diesel blended fuel conditions, using LPG-Diesel blended fuels with various blended rates (0%, 10%, 20%, 30%, 40%). Comparative results are given for various engine speeds and loads for conventional Diesel and blended fuels, revealing the effect of blended fuel combustion on engine performance and exhaust emissions

Mechanical engineers' handbook, materials and engineering mechanics

CERN Document Server

Kutz, Myer

2015-01-01

Full coverage of materials and mechanical design inengineering Mechanical Engineers' Handbook, Fourth Edition provides aquick guide to specialized areas you may encounter in your work,giving you access to the basics of each and pointing you towardtrusted resources for further reading, if needed. The accessibleinformation inside offers discussions, examples, and analyses ofthe topics covered. This first volume covers materials and mechanical design, givingyou accessible and in-depth access to the most common topics you'llencounter in the discipline: carbon and alloy steels, stainlesssteels, a

Perspectives of ukrainian mechanical engineering development

OpenAIRE

Dyrda, E.; Schepetkova, A.; Galushko, O.

2013-01-01

Theses are devoted to problems and perspectives of Ukrainian mechanical engineering development. Role of mechanical engineering in national economy is described. Problems of mechanical engineering, such as losing the cometetive advantages, production decreasing, debts growing, ineffective assets structure, are investigated. Influence of European integration process on mechanical engineering enterprises is discussed.

Document imaging finding niche in petroleum industry

International Nuclear Information System (INIS)

Cisco, S.L.

1992-01-01

Optical disk-based document imaging systems can reduce operating costs, save office space, and improve access to necessary information for petroleum companies that have extensive records in various formats. These imaging systems help solve document management problems to improve technical and administrative operations. Enron Gas Pipeline Group has installed a document imaging system for engineering applications to integrate records stored on paper, microfilm, or computer-aided drafting (CAD) systems. BP Exploration Inc. recently implemented a document imaging system for administrative applications. The company is evaluating an expansion of the system to include engineering and technical applications. The petroleum industry creates, acquires, distributes, and retrieves enormous amounts of data and information, which are stored on multiple media, including paper, microfilm, and electronic formats. There are two main factors responsible for the immense information storage requirements in the petroleum industry

Generation and characterization of diesel engine combustion emissions from petroleum diesel and soybean biodiesel fuels and application for inhalation exposure studies

Science.gov (United States)

Biodiesel made from the transesterification of plant- and anmal-derived oils is an important alternative fuel source for diesel engines. Although numerous studies have reported health effects associated with petroleum diesel emissions, information on biodiesel emissions are more ...

Modern mechanical engineering research, development and education

CERN Document Server

2014-01-01

This book covers modern subjects of mechanical engineering such as nanomechanics and nanotechnology, mechatronics and robotics, computational mechanics, biomechanics, alternative energies, sustainability as well as all aspects related with mechanical engineering education. The chapters help enhance the understanding of both the fundamentals of mechanical engineering and its application to the solution of problems in modern industry. This book is suitable for students, both in final undergraduate mechanical engineering courses or at the graduate level. It also serves as a useful reference for academics, mechanical engineering researchers, mechanical, materials and manufacturing engineers, professionals in related with mechanical engineering.

Generation and characterization of diesel engine combustion emissions from petroleum diesel and soybean biodiesel fuels and application for inhalation exposure studies.

NARCIS (Netherlands)

Mutlu, E.; Nash, D.G.; King, C.; Krantz, T.Q.; Preston, W.T.; Kooter, I.M.; Higuchi, M.; DeMarini, D.; Linak, W.P.; Ian Gilmour, M.

2015-01-01

Biodiesel made from the transesterification of plant- and animal-derived oils is an important alternative fuel source for diesel engines. Although numerous studies have reported health effects associated with petroleum diesel emissions, information on biodiesel emissions are more limited. To this

Photolysis of petroleum

International Nuclear Information System (INIS)

Bobra, M.

1992-05-01

A study was conducted to examine the chemical and physical changes that occur in oils as a result of photooxidation. A literature review of recent studies in petroleum photochemistry revealed reported effects of photo-induced reactions in petroleum, including changes in color, polymerization, solidification, increases in solubility and toxicity, and changes in interfacial properties. A list of products reported as a result of photolysis of petroleum is presented, including such compounds as aldehydes, ketones, esters, and lactones. The photoreactivity of various petroleum components is discussed and mechanisms of photooxidation of petroleum are suggested. In the experimental portion of the study, a variety of crude oils and petroleum products were used to determine how different oils are affected by photolysis, and to examine the importance of photolysis as a weathering process. Photooxidation products from several oils were isolated and identified, including aliphatic and aromatic acids, alcohols, and phenols. Some physical manifestations attributed to photolysis included yellowing, formation of precipitates or crusts, increases in density and viscosity with time, increases of asphaltene content in some oils, changes in pH of the surrounding water, and emulsification. 51 refs., 38 figs., 18 tabs

Teaching Continuum Mechanics in a Mechanical Engineering Program

Science.gov (United States)

Liu, Yucheng

2011-01-01

This paper introduces a graduate course, continuum mechanics, which is designed for and taught to graduate students in a Mechanical Engineering (ME) program. The significance of continuum mechanics in engineering education is demonstrated and the course structure is described. Methods used in teaching this course such as topics, class…

System dynamics for mechanical engineers

CERN Document Server

Davies, Matthew

2015-01-01

This textbook is ideal for mechanical engineering students preparing to enter the workforce during a time of rapidly accelerating technology, where they will be challenged to join interdisciplinary teams. It explains system dynamics using analogies familiar to the mechanical engineer while introducing new content in an intuitive fashion. The fundamentals provided in this book prepare the mechanical engineer to adapt to continuous technological advances with topics outside traditional mechanical engineering curricula by preparing them to apply basic principles and established approaches to new problems. This book also: ·         Reinforces the connection between the subject matter and engineering reality ·         Includes an instructor pack with the online publication that describes in-class experiments with minimal preparation requirements ·         Provides content dedicated to the modeling of modern interdisciplinary technological subjects, including opto-mechanical systems, high...

Rare and expensive petroleum: impact on careers

International Nuclear Information System (INIS)

Thomas, E.; Krasowski, T.; Kerdraon, Y.; Drevet, R.; Andreis, D.; Pouille, J.P.; Villoslada Prado, P.; Sigaud, J.B.

2006-01-01

Oil peak, reserves depletion, greenhouse effect, pollution, uncertain future and international insecurity could be negative arguments to discourage candidates to start up a career in the petroleum industry. This press kit presents testimonies of young professionals who explain their motivations for committing themselves in this way. Testimonies are chosen in various domains of the petroleum industry: geophysics, exploration, processes, refining, and engines technology. (J.S.)

Engineering quantum mechanics

CERN Document Server

Ahn, Doyeol

2011-01-01

A clear introduction to quantum mechanics concepts Quantum mechanics has become an essential tool for modern engineering, particularly due to the recent developments in quantum computing as well as the rapid progress in optoelectronic devices. Engineering Quantum Mechanics explains the fundamentals of this exciting field, providing broad coverage of both traditional areas such as semiconductor and laser physics as well as relatively new yet fast-growing areas such as quantum computation and quantum information technology. The book begins with basic quantum mechanics, reviewing measurements and probability, Dirac formulation, the uncertainty principle, harmonic oscillator, angular momentum eigenstates, and perturbation theory. Then, quantum statistical mechanics is explored, from second quantization and density operators to coherent and squeezed states, coherent interactions between atoms and fields, and the Jaynes-Cummings model. From there, the book moves into elementary and modern applications, discussing s...

Petroleum software and the road ahead

International Nuclear Information System (INIS)

Heggelund, D.G.

1996-01-01

Regardless of what software vendors want to do, in the end, it is the user, through his/her choices of software products, who will decide what the software of the petroleum-engineering industry will look like. In this article, the author has looked at several items that will impact the future of petroleum-engineering software. Out of these, two will stand out: (1) the adoption of a single integrated dynamic reservoir model and (2) the move to a client/server architecture. However, the biggest challenge for both vendors and users will be to manage change. This will require users to participate more actively in the development of new technology and to be willing to pay for it, and it will require vendors to adopt standards more readily

Hamiltonian mechanics limits microscopic engines

Science.gov (United States)

Anglin, James; Gilz, Lukas; Thesing, Eike

2015-05-01

We propose a definition of fully microscopic engines (micro-engines) in terms of pure mechanics, without reference to thermodynamics, equilibrium, or cycles imposed by external control, and without invoking ergodic theory. This definition is pragmatically based on the observation that what makes engines useful is energy transport across a large ratio of dynamical time scales. We then prove that classical and quantum mechanics set non-trivial limits-of different kinds-on how much of the energy that a micro-engine extracts from its fuel can be converted into work. Our results are not merely formal; they imply manageable design constraints on micro-engines. They also suggest the novel possibility that thermodynamics does not emerge from mechanics in macroscopic regimes, but rather represents the macroscopic limit of a generalized theory, valid on all scales, which governs the important phenomenon of energy transport across large time scale ratios. We propose experimental realizations of the dynamical mechanisms we identify, with trapped ions and in Bose-Einstein condensates (``motorized bright solitons'').

Standardized Curriculum for Diesel Engine Mechanics.

Science.gov (United States)

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

Standardized curricula are provided for two courses for the secondary vocational education program in Mississippi: diesel engine mechanics I and II. The eight units in diesel engine mechanics I are as follows: orientation; shop safety; basic shop tools; fasteners; measurement; engine operating principles; engine components; and basic auxiliary…

1992 petroleum software directory

International Nuclear Information System (INIS)

Anon.

1991-01-01

This book is designed especially for the petroleum industry. Each program listing includes a description of the function, language and memory requirements, operating systems, special accessories required, compatibles and pricing information. A separate section lists the more than 600 companies that produce and sell the programs. Companies are listed alphabetically and include address, phone, fax and telex numbers as well as contact names for each location. Many company listings also include distributors. This book includes information on Accounting/Statistics, Design/Construction/Engineering Graphics, Drilling Engineering and Equipment, Economics/Financial Analysis, Engineering, Exploration, Land and Leasing, Maintenance and Repair/Quality Control/Monitoring, Manufacturing, Maps, Marketing, Pipelines/Shipping/Storage, Production Engineering and Recovery Methods, Synthetic/Alternate Resources and Fuels

Mechanical design engineering handbook

CERN Document Server

Childs, Peter R N

2013-01-01

Mechanical Design Engineering Handbook is a straight-talking and forward-thinking reference covering the design, specification, selection, use and integration of machine elements fundamental to a wide range of engineering applications. Develop or refresh your mechanical design skills in the areas of bearings, shafts, gears, seals, belts and chains, clutches and brakes, springs, fasteners, pneumatics and hydraulics, amongst other core mechanical elements, and dip in for principles, data and calculations as needed to inform and evaluate your on-the-job decisions. Covering the full spectrum

Introductory Education for Mechanical Engineering by Exercise in Mechanical Disassembly

Science.gov (United States)

Matsui, Yoshio; Asakawa, Naoki; Iwamori, Satoru

An introductory program “Exercise for engineers in mechanical disassembly” is an exercise that ten students of every team disassemble a motor scooter to the components and then assemble again to the initial form in 15 weeks. The purpose of this program is to introduce mechanical engineering by touching the real machine and learning how it is composed from various mechanical parts to the students at the early period after the entrance into the university. Additional short lectures by young teachers and a special lecture by a top engineer in the industry encourage the students to combine the actual machine and the mechanical engineering subjects. Furthermore, various educations such as group leader system, hazard prediction training, parts filing are included in this program. As a result, students recognize the importance of the mechanical engineering study and the way of group working.

REGISTER ANALYSIS OF THE CONVERSATIONS AMONG PETROLEUM ENGINEERS

Directory of Open Access Journals (Sweden)

Siti Nurani

2015-03-01

Full Text Available This present research aims at identifying register used in the conversations among petroleum engineers by examining the linguistic feature which is viewed from the aspect of the field, the tenor and the mode of discourse of the Systemic Functional Linguistics (SFL approach. Findings show that in the field of discourse, all terms of register found in the experiential domain analysis function as technical terms, of which the two major forms of nouns and verbs (i.e., single-word and compound/phrasal word forms are the most frequent categories identified among other kinds of technical terms. The goal orientation appears to have both short and long term while the social activity results in exchanges among participants. In the tenor of discourse, the agentive role is said to be equal and the social role is considered as non-hierarchic. The social distance within the interaction is said to be minimal which is excessively characterized by the use of informal form of expressions. In the mode of discourse, the language role exists equally of both constitutive and ancillary identified by the use of present simple tense and non-present tenses, that is, future simple, past simple and present perfect. The channel is in phonic form. The medium is in spoken with visual contact as it is largely characterized by the use of endophoric reference as well as pronouns.

Mechanical Engineering Practice – using a simple Stirling engine as case

DEFF Research Database (Denmark)

Meyer, Knud Erik

2011-01-01

The first technical course that students in mechanical engineering take at the Technical University of Denmark is called “Mechanical Engineering Practice”. We have used a simple Stirling engine as a design-implement project. Students were asked to design and build a heat engine using materials....... The Stirling engine worked well in the drawing assignments. The Stirling engine also served as illustration of coming courses in mechanical engineering. The resulting engines had large variations in their design and most groups succeeded in building a functioning engine. However, achieved efficiencies were...... obtained by their own means and were competing on achieving the highest efficiency. We added an extra dimension to the project by making detailed measurements of the pressure variation to check simple thermodynamic models of the engine. The course had integrated lessons in sketching and technical drawing...

Mechanical engineering science in SI units

CERN Document Server

Gwyther, J L; Williams, G

1970-01-01

0.1 Mechanical Engineering Science covers various fundamental concepts that are essential in the practice of mechanical engineering. The title is comprised of 19 chapters that detail various topics, including chemical and physical laws. The coverage of the book includes Newtonian laws, mechanical energy, friction, stress, and gravity. The text also discusses the chemical aspects of mechanical engineering, which include gas laws, states of matter, and fuel combustion. The last chapter tackles concerns in laboratory experiments. The book will be of great use to students of mechanical eng

Engineering Change Management Method Framework in Mechanical Engineering

Science.gov (United States)

Stekolschik, Alexander

2016-11-01

Engineering changes make an impact on different process chains in and outside the company, and lead to most error costs and time shifts. In fact, 30 to 50 per cent of development costs result from technical changes. Controlling engineering change processes can help us to avoid errors and risks, and contribute to cost optimization and a shorter time to market. This paper presents a method framework for controlling engineering changes at mechanical engineering companies. The developed classification of engineering changes and accordingly process requirements build the basis for the method framework. The developed method framework comprises two main areas: special data objects managed in different engineering IT tools and process framework. Objects from both areas are building blocks that can be selected to the overall business process based on the engineering process type and change classification. The process framework contains steps for the creation of change objects (both for overall change and for parts), change implementation, and release. Companies can select singleprocess building blocks from the framework, depending on the product development process and change impact. The developed change framework has been implemented at a division (10,000 employees) of a big German mechanical engineering company.

Treatment of petroleum hydrocarbon polluted environment through bioremediation: a review.

Science.gov (United States)

Singh, Kriti; Chandra, Subhash

2014-01-01

Bioremediation play key role in the treatment of petroleum hydrocarbon contaminated environment. Exposure of petroleum hydrocarbon into the environment occurs either due to human activities or accidentally and cause environmental pollution. Petroleum hydrocarbon cause many toxic compounds which are potent immunotoxicants and carcinogenic to human being. Remedial methods for the treatment of petroleum contaminated environment include various physiochemical and biological methods. Due to the negative consequences caused by the physiochemical methods, the bioremediation technology is widely adapted and considered as one of the best technology for the treatment of petroleum contaminated environment. Bioremediation utilizes the natural ability of microorganism to degrade the hazardous compound into simpler and non hazardous form. This paper provides a review on the role of bioremediation in the treatment of petroleum contaminated environment, discuss various hazardous effects of petroleum hydrocarbon, various factors influencing biodegradation, role of various enzymes in biodegradation and genetic engineering in bioremediation.

Petroleum service projects in the Gulf of Guinea

Science.gov (United States)

Ken-Worgu, Kenneth Chukwumeka

2011-07-01

The goal of this record of study is to examine the major facets involved in managing several petroleum service projects located in three different countries in the Gulf of Guinea simultaneously, while effectively engaging in business development activities for the Oil and Industrial Services Group (OIS). This work also furnishes adequate background on related subject matters to enable understanding of the projects presented. The petroleum services sector is the back bone of the oil and gas industry. Services companies are vital to the success of all petroleum and energy producers in the USA, the Gulf of Guinea and the world. There is a need and demand for these service companies because they play various roles such as logistics, drilling, construction, dredging, pipe laying, procurement, food supply, human resource supply, etc. The Gulf of Guinea comprises of countries from west and central Africa. This project was limited to Nigeria, Equatorial Guinea and Cameroon. This area holds the largest petroleum reserves in Africa and plays a vital role in the global supply of petroleum. The Oil and Industrial Services Group (OIS), plans to establish herself as one of the leading petroleum service companies in this gulf. To manage this expansion, I have taken the role of Gulf of Guinea manager to apply my background as a petroleum engineer as well as my business skills to build a successful division of the company. This work provides a record of study of the management of services, projects and contracts carried out by the OIS group in the gulf of Guinea. The following are the specific projects in the Gulf of Guinea that I participated in: Managing delivering, maintenance and marketing of offshore vessels, Offshore pipe laying project, Integrated pipeline maintenance project, Development a petroleum technical training facilities, Agbami pipe insulation project, Engineering lift project and Capital budgeting analysis for potential investments. The details of the specific

Proceedings of the ENCIT 2008: 12. Brazilian congress of thermal sciences and engineering

International Nuclear Information System (INIS)

Koury, Ricardo Nicolau Nassar; Barbosa, Marcos Pinotti

2008-01-01

Theoretical and experimental papers are presented in this proceedings covering the following subjects: petroleum, industry, fractions and distillates, gas turbines and power plants, reservoir engineering, oil field and wells, offshore operation, electric power generation, aerospace engineering, heat and mass transfer, refrigeration, ventilation and building simulation, nuclear engineering, instrumentation and metrology, fluid mechanics, rheology, environment and numerical analysis

Inverse Theory for Petroleum Reservoir Characterization and History Matching

Science.gov (United States)

Oliver, Dean S.; Reynolds, Albert C.; Liu, Ning

This book is a guide to the use of inverse theory for estimation and conditional simulation of flow and transport parameters in porous media. It describes the theory and practice of estimating properties of underground petroleum reservoirs from measurements of flow in wells, and it explains how to characterize the uncertainty in such estimates. Early chapters present the reader with the necessary background in inverse theory, probability and spatial statistics. The book demonstrates how to calculate sensitivity coefficients and the linearized relationship between models and production data. It also shows how to develop iterative methods for generating estimates and conditional realizations. The text is written for researchers and graduates in petroleum engineering and groundwater hydrology and can be used as a textbook for advanced courses on inverse theory in petroleum engineering. It includes many worked examples to demonstrate the methodologies and a selection of exercises.

Processing (refining) of petroleum and natural gases. Pererabotka neftyanykh i prirodnykh gazov

Energy Technology Data Exchange (ETDEWEB)

Berlin, M A; Gorechenkov, V G; Volkov, N P

1981-01-01

A discussion is made of the theoretical principles underlying the processes involved in the processing of natural and petroleum gases and gas condensate. Information is given on apparatus, engineering systems, and machine methods for the designing of gas refining plants. The book is intended for engineers and operation personnel of gas refining plants, and might also be useful to senior undergraduates at chemistry and petroleum institutes of higher learning. 278 references, 54 tables.

Updating the U.S. Life Cycle GHG Petroleum Baseline to 2014 with Projections to 2040 Using Open-Source Engineering-Based Models.

Science.gov (United States)

Cooney, Gregory; Jamieson, Matthew; Marriott, Joe; Bergerson, Joule; Brandt, Adam; Skone, Timothy J

2017-01-17

The National Energy Technology Laboratory produced a well-to-wheels (WTW) life cycle greenhouse gas analysis of petroleum-based fuels consumed in the U.S. in 2005, known as the NETL 2005 Petroleum Baseline. This study uses a set of engineering-based, open-source models combined with publicly available data to calculate baseline results for 2014. An increase between the 2005 baseline and the 2014 results presented here (e.g., 92.4 vs 96.2 g CO 2 e/MJ gasoline, + 4.1%) are due to changes both in modeling platform and in the U.S. petroleum sector. An updated result for 2005 was calculated to minimize the effect of the change in modeling platform, and emissions for gasoline in 2014 were about 2% lower than in 2005 (98.1 vs 96.2 g CO 2 e/MJ gasoline). The same methods were utilized to forecast emissions from fuels out to 2040, indicating maximum changes from the 2014 gasoline result between +2.1% and -1.4%. The changing baseline values lead to potential compliance challenges with frameworks such as the Energy Independence and Security Act (EISA) Section 526, which states that Federal agencies should not purchase alternative fuels unless their life cycle GHG emissions are less than those of conventionally produced, petroleum-derived fuels.

Mechanics of materials an introduction to engineering technology

CERN Document Server

Ghavami, Parviz

2015-01-01

This book, framed in the processes of engineering analysis and design, presents concepts in mechanics of materials for students in two-year or four-year programs in engineering technology, architecture, and building construction, as well as for students in vocational schools and technical institutes. Using the principles and laws of mechanics, physics, and the fundamentals of engineering, Mechanics of Materials: An Introduction for Engineering Technology will help aspiring and practicing engineers and engineering technicians from across disciplines—mechanical, civil, chemical, and electrical—apply concepts of engineering mechanics for analysis and design of materials, structures, and machine components. The book is ideal for those seeking a rigorous, algebra/trigonometry-based text on the mechanics of materials. This book also: ·       Elucidates concepts of engineering mechanics in materials, including stress and strain, force systems on structures, moment of inertia, and shear and bending moments...

Practical electrical engineering

CERN Document Server

N Makarov, Sergey; Bitar, Stephen J

2016-01-01

This textbook provides comprehensive, in-depth coverage of the fundamental concepts of electrical and computer engineering. It is written from an engineering perspective, with special emphasis on circuit functionality and applications. Reliance on higher-level mathematics and physics, or theoretical proofs has been intentionally limited in order to prioritize the practical aspects of electrical engineering. This text is therefore suitable for a number of introductory circuit courses for other majors such as robotics, mechanical, biomedical, aerospace, civil, architecture, petroleum, and industrial engineering. The authors’ primary goal is to teach the aspiring engineering student all fundamental tools needed to understand, analyze and design a wide range of practical circuits and systems. Their secondary goal is to provide a comprehensive reference, for both major and non-major students as well as practicing engineers. Provides a self-contained, fundamental textbook on electric circuits and basic electronic...

An introduction to mechanical engineering, pt.2

CERN Document Server

Clifford, Michael

2010-01-01

An Introduction to Mechanical Engineering: Part 2 is an essential text for all second-year undergraduate students as well as those studying foundation degrees and HNDs. The text provides thorough coverage of the following core engineering topics:Fluid dynamicsThermodynamicsSolid mechanicsControl theory and techniquesMechanical power, loads and transmissionsStructural vibrationAs well as mechanical engineers, the text will be highly relevant to automotive, aeronautical/aerospace and general engineering students.The material in this book has full student and lecturer support on an accompanying w

An introduction to mechanical engineering, pt.1

CERN Document Server

Clifford, Michael; Shipway, Philip

2012-01-01

An Introduction to Mechanical Engineering is an essential text for all first-year undergraduate students as well as those studying for foundation degrees and HNDs. The text gives a thorough grounding in the following core engineering topics: thermodynamics, fluid mechanics, solid mechanics, dynamics, electricals and electronics, and materials science. As well as mechanical engineers, the text will be highly relevant to civil, automotive, aeronautical/aerospace and general engineering students.The text is written by an experienced team of first-year lecturers at the internationally renowned Uni

Estimating decades-long trends in petroleum field energy return on investment (EROI) with an engineering-based model

Science.gov (United States)

Tripathi, Vinay S.

2017-01-01

This paper estimates changes in the energy return on investment (EROI) for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE). The modeled fields include Cantarell (Mexico), Forties (U.K.), Midway-Sunset (U.S.), Prudhoe Bay (U.S.), and Wilmington (U.S.). Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER) and external energy ratio (EER) are calculated, each using two measures of energy outputs, (1) oil-only and (2) all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy). All fields display significant declines in NER over the modeling period driven by a combination of (1) reduced petroleum production and (2) increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs). The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases. PMID:28178318

Estimating decades-long trends in petroleum field energy return on investment (EROI) with an engineering-based model.

Science.gov (United States)

Tripathi, Vinay S; Brandt, Adam R

2017-01-01

This paper estimates changes in the energy return on investment (EROI) for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE). The modeled fields include Cantarell (Mexico), Forties (U.K.), Midway-Sunset (U.S.), Prudhoe Bay (U.S.), and Wilmington (U.S.). Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER) and external energy ratio (EER) are calculated, each using two measures of energy outputs, (1) oil-only and (2) all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy). All fields display significant declines in NER over the modeling period driven by a combination of (1) reduced petroleum production and (2) increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs). The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases.

Estimating decades-long trends in petroleum field energy return on investment (EROI with an engineering-based model.

Directory of Open Access Journals (Sweden)

Vinay S Tripathi

Full Text Available This paper estimates changes in the energy return on investment (EROI for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE. The modeled fields include Cantarell (Mexico, Forties (U.K., Midway-Sunset (U.S., Prudhoe Bay (U.S., and Wilmington (U.S.. Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER and external energy ratio (EER are calculated, each using two measures of energy outputs, (1 oil-only and (2 all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy. All fields display significant declines in NER over the modeling period driven by a combination of (1 reduced petroleum production and (2 increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs. The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases.

The characteristics of mechanical engineering systems

CERN Document Server

Holmes, R

1977-01-01

The Characteristics of Mechanical Engineering Systems focuses on the characteristics that must be considered when designing a mechanical engineering system. Mechanical systems are presented on the basis of component input-output relationships, paying particular attention to lumped-parameter problems and the interrelationships between lumped components or """"black-boxes"""" in an engineering system. Electric motors and generators are treated in an elementary manner, and the principles involved are explained as far as possible from physical and qualitative reasoning. This book is comprised of

Handbook of mechanical engineering terms

CERN Document Server

Ramalingam, KK

2009-01-01

About the Book: The Handbook of Mechanical Engineering terms contains short, precise definitions of about four thousand terms. These terms have been collected from different sources, edited and grouped under twenty six parts and given alphabetically under each part for easy reference. The book will be a source of guidance and help to the students, staff and practising engineers in understanding and updating the subject matter. Contents: The Handbook of Mechanical Engineering terms contains short, precise definitions of about four thousand terms. These terms have been collected from differ

46 CFR 12.15-13 - Deck engine mechanic.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Deck engine mechanic. 12.15-13 Section 12.15-13 Shipping... ENDORSEMENTS Qualified Member of the Engine Department § 12.15-13 Deck engine mechanic. (a) An applicant for an endorsement as deck engine mechanic shall be a person holding an MMC or MMD endorsed as junior engineer. The...

Expose Mechanical Engineering Students to Biomechanics Topics

Science.gov (United States)

Shen, Hui

2011-01-01

To adapt the focus of engineering education to emerging new industries and technologies nationwide and in the local area, a biomechanics module has been developed and incorporated into a mechanical engineering technical elective course to expose mechanical engineering students at ONU (Ohio Northern University) to the biomedical engineering topics.…

Mechanical engineer's reference book

CERN Document Server

Parrish, A

1973-01-01

Mechanical Engineer's Reference Book: 11th Edition presents a comprehensive examination of the use of Systéme International d' Unités (SI) metrication. It discusses the effectiveness of such a system when used in the field of engineering. It addresses the basic concepts involved in thermodynamics and heat transfer. Some of the topics covered in the book are the metallurgy of iron and steel; screw threads and fasteners; hole basis and shaft basis fits; an introduction to geometrical tolerancing; mechanical working of steel; high strength alloy steels; advantages of making components as castings

Fluid mechanics for engineers. A graduate textbook

Energy Technology Data Exchange (ETDEWEB)

Schobeiri, Meinhard T. [Texas A and M Univ., College Station, TX (United States). Dept. of Mechanical Engineering

2010-07-01

The contents of this book covers the material required in the Fluid Mechanics Graduate Core Course (MEEN-621) and in Advanced Fluid Mechanics, a Ph.D-level elective course (MEEN-622), both of which I have been teaching at Texas A and M University for the past two decades. While there are numerous undergraduate fluid mechanics texts on the market for engineering students and instructors to choose from, there are only limited texts that comprehensively address the particular needs of graduate engineering fluid mechanics courses. To complement the lecture materials, the instructors more often recommend several texts, each of which treats special topics of fluid mechanics. This circumstance and the need to have a textbook that covers the materials needed in the above courses gave the impetus to provide the graduate engineering community with a coherent textbook that comprehensively addresses their needs for an advanced fluid mechanics text. Although this text book is primarily aimed at mechanical engineering students, it is equally suitable for aerospace engineering, civil engineering, other engineering disciplines, and especially those practicing professionals who perform CFD-simulation on a routine basis and would like to know more about the underlying physics of the commercial codes they use. Furthermore, it is suitable for self study, provided that the reader has a sufficient knowledge of calculus and differential equations. (orig.)

Engineering science and mechanics department head named

OpenAIRE

Nystrom, Lynn A.

2004-01-01

Ishwar K. Puri, professor of mechanical engineering and executive associate dean of engineering at the University of Illinois at Chicago, will become the head of Virginia Tech•À_ó»s Department of Engineering Science and Mechanics Aug. 1.

The Stirling engine mechanism optimization

Directory of Open Access Journals (Sweden)

Jiří Podešva

2016-03-01

Full Text Available A special type of the gas engine with external combustion is called Stirling engine. The mechanism has two pistons with two volumes inside. The pistons are connected together through cooler, regenerator and warmer. The engine effectivity depends on the piston movement behaviour. The usual sinusoidal time curve leads to low effectiveness. The quick movement from lower to upper position with a certain delay in both top and bottom dead centres is more effective. The paper deals with three types of mechanisms, analyzing the piston movement, and their behavior. Special emphasize is taken to the piston movement regime.

Korean society of mechanical engineers 60 years

International Nuclear Information System (INIS)

2005-12-01

This book introduces 60 years of Korean society of mechanical engineers with birth, foundation, development process, change of enforcement regulation and articles of association, important data of this association, 60 years of parts, committee and branch, business of association like academic event, publication, technical development business, supporting research centers, bond Korean society of mechanical engineers and mechanical industry and development of related organizations, development for industrial fields and development direction of Korean society of mechanical engineers.

Micro electromechanical systems (MEMS) for mechanical engineers

Energy Technology Data Exchange (ETDEWEB)

Lee, A. P., LLNL

1996-11-18

The ongoing advances in Microelectromechanical Systems (MEMS) are providing man-kind the freedom to travel to dimensional spaces never before conceivable. Advances include new fabrication processes, new materials, tailored modeling tools, new fabrication machines, systems integration, and more detailed studies of physics and surface chemistry as applied to the micro scale. In the ten years since its inauguration, MEMS technology is penetrating industries of automobile, healthcare, biotechnology, sports/entertainment, measurement systems, data storage, photonics/optics, computer, aerospace, precision instruments/robotics, and environment monitoring. It is projected that by the turn of the century, MEMS will impact every individual in the industrial world, totaling sales up to $14 billion (source: System Planning Corp.). MEMS programs in major universities have spawned up all over the United States, preparing the brain-power and expertise for the next wave of MEMS breakthroughs. It should be pointed out that although MEMS has been initiated by electrical engineering researchers through the involvement of IC fabrication techniques, today it has evolved such that it requires a totally multi-disciplinary team to develop useful devices. Mechanical engineers are especially crucial to the success of MEMS development, since 90% of the physical realm involved is mechanical. Mechanical engineers are needed for the design of MEMS, the analysis of the mechanical system, the design of testing apparatus, the implementation of analytical tools, and the packaging process. Every single aspect of mechanical engineering is being utilized in the MEMS field today, however, the impact could be more substantial if more mechanical engineers are involved in the systems level designing. In this paper, an attempt is made to create the pathways for a mechanical engineer to enter in the MEMS field. Examples of application in optics and medical devices will be used to illustrate how mechanical

Desulfurization of petroleum by Co-60 gamma irradiation and analysis of products using GC-MS

International Nuclear Information System (INIS)

Mathuthu, M.; Tshivhase, V.M.; Olobatoke, R.Y.; Gaxela, N.N.

2014-01-01

Sulfur is an undesirable hetero-atom that has negative on motor engines if present in quantities between 50 and 180.000 ppm. Research has shown that sour petroleum can be 'sweetened' by gamma irradiation to de-sulfurize the crude oil. In this research we will report experimental results of desulfurizing petroleum locally procured. The objective is to improve the quality of product delivered to the motor market and also reduce the environmental pollution due to SO 2 emissions from engines. The gamma irradiated (de-sulfurized petroleum was chemically analyzed using GC-MS. The preliminary results show that the petroleum is polymerized by gamma radiation to higher molecular mass. The un-irradiated petroleum had a sulfur concentration of 3.24% and 0.020% wt after gamma irradiation. The sulfur content was reduced by a factor of about 160 when dose was increased from zero to 50 kGys. GC-MS Chromatographs are presented for the identified hydrocarbons after gamma irradiation. (authors)

Mechanical engineering principles

CERN Document Server

Bird, John

2014-01-01

A student-friendly introduction to core engineering topicsThis book introduces mechanical principles and technology through examples and applications, enabling students to develop a sound understanding of both engineering principles and their use in practice. These theoretical concepts are supported by 400 fully worked problems, 700 further problems with answers, and 300 multiple-choice questions, all of which add up to give the reader a firm grounding on each topic.The new edition is up to date with the latest BTEC National specifications and can also be used on undergraduate courses in mecha

Computational structural mechanics for engine structures

Science.gov (United States)

Chamis, C. C.

1989-01-01

The computational structural mechanics (CSM) program at Lewis encompasses: (1) fundamental aspects for formulating and solving structural mechanics problems, and (2) development of integrated software systems to computationally simulate the performance/durability/life of engine structures. It is structured to mainly supplement, complement, and whenever possible replace, costly experimental efforts which are unavoidable during engineering research and development programs. Specific objectives include: investigate unique advantages of parallel and multiprocesses for: reformulating/solving structural mechanics and formulating/solving multidisciplinary mechanics and develop integrated structural system computational simulators for: predicting structural performances, evaluating newly developed methods, and for identifying and prioritizing improved/missing methods needed. Herein the CSM program is summarized with emphasis on the Engine Structures Computational Simulator (ESCS). Typical results obtained using ESCS are described to illustrate its versatility.

The United Nations Framework Classification for World Petroleum Resources

Science.gov (United States)

Ahlbrandt, T.S.; Blystad, P.; Young, E.D.; Slavov, S.; Heiberg, S.

2003-01-01

The United Nations has developed an international framework classification for solid fuels and minerals (UNFC). This is now being extended to petroleum by building on the joint classification of the Society of Petroleum Engineers (SPE), the World Petroleum Congresses (WPC) and the American Association of Petroleum Geologists (AAPG). The UNFC is a 3-dimansional classification. This: Is necessary in order to migrate accounts of resource quantities that are developed on one or two of the axes to the common basis; Provides for more precise reporting and analysis. This is particularly useful in analyses of contingent resources. The characteristics of the SPE/WPC/AAPG classification has been preserved and enhanced to facilitate improved international and national petroleum resource management, corporate business process management and financial reporting. A UN intergovernmental committee responsible for extending the UNFC to extractive energy resources (coal, petroleum and uranium) will meet in Geneva on October 30th and 31st to review experiences gained and comments received during 2003. A recommended classification will then be delivered for consideration to the United Nations through the Committee on Sustainable Energy of the Economic Commission for Europe (UN ECE).

Mechanical engineers' handbook, energy and power

CERN Document Server

Kutz, Myer

2015-01-01

The engineer's ready reference for mechanical power and heat Mechanical Engineer's Handbook provides the mostcomprehensive coverage of the entire discipline, with a focus onexplanation and analysis. Packaged as a modular approach, thesebooks are designed to be used either individually or as a set,providing engineers with a thorough, detailed, ready reference ontopics that may fall outside their scope of expertise. Each bookprovides discussion and examples as opposed to straight data andcalculations, giving readers the immediate background they needwhile pointing them toward more in-depth infor

Laws of the electrochemical soils remediation from petroleum pollution

Energy Technology Data Exchange (ETDEWEB)

Korolev, V.A. [Moscow State Univ. (Russian Federation)

2001-07-01

The man-caused petroleum pollution of humus and soils in places of oil production, and also the pollution of geological environment by petroleum is carried out in growing scales. Very much frequently of ground and soils become soiled by petroleum at failures during transportation of petroleum. The humus and clay soils polluted by petroleum causes destruction ecosystems and landscapes. Therefore finding - out of the nature and mechanisms of interaction water-saturated dispersed soils with the liquid hydrocarbons becomes one of priority problems in the field of ecological geology. The development of methods of electrochemical clearing soils from the liquid hydrocarbons pollution is the important task too. Therefore, the study of dependences of a double electrical layer (DEL) parameters of the water-petroleum-saturated caolinite clay and electrochemical migration in it of petroleum was the purpose of the present work. (orig.)

Engineered in situ bioremediation of a petroleum hydrocarbon-contaminated aquifer: assessment of mineralization based on alkalinity, inorganic carbon and stable carbon isotope balances

Science.gov (United States)

Hunkeler, Daniel; Höhener, Patrick; Bernasconi, Stefano; Zeyer, Josef

1999-04-01

A concept is proposed to assess in situ petroleum hydrocarbon mineralization by combining data on oxidant consumption, production of reduced species, CH 4, alkalinity and dissolved inorganic carbon (DIC) with measurements of stable isotope ratios. The concept was applied to a diesel fuel contaminated aquifer in Menziken, Switzerland, which was treated by engineered in situ bioremediation. In the contaminated aquifer, added oxidants (O 2 and NO 3-) were consumed, elevated concentrations of Fe(II), Mn(II), CH 4, alkalinity and DIC were detected and the DIC was generally depleted in 13C compared to the background. The DIC production was larger than expected based on the consumption of dissolved oxidants and the production of reduced species. Stable carbon isotope balances revealed that the DIC production in the aquifer originated mainly from microbial petroleum hydrocarbon mineralization, and that geochemical reactions such as carbonate dissolution produced little DIC. This suggests that petroleum hydrocarbon mineralization can be underestimated if it is determined based on concentrations of dissolved oxidants and reduced species.

Mechanical Engineering Department technical abstracts

International Nuclear Information System (INIS)

1984-01-01

The Mechanical Engineering Department publishes abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). General information about the current role and activities of each of the Department's seven divisions precedes the technical abstracts. Further information about a division's work may be obtained from the division leader, whose name is given at the end of each divisional summary. The Department's seven divisions are as follows: Nuclear Test Engineering Division, Nuclear Explosives Engineering Division, Weapons Engineering Division, Energy Systems Engineering Division, Engineering Sciences Division, Magnetic Fusion Engineering Division and Materials Fabrication Division

Petroleum Characterisation and Reservoir Dynamics - The Froey Field and the Rind Discovery, Norwegian Continental Shelf

Energy Technology Data Exchange (ETDEWEB)

Bhullar, Abid G.

1999-07-01

The objective of this thesis is to apply the fundamental principles of petroleum geochemistry integrated with petroleum/reservoir engineering and geological concepts to the dynamics and characterisation of petroleum reservoirs. The study is based on 600 core samples and 9 DST oils from 11 wells in the Froey Field and the Rind Discovery. The work is presented in five papers. Paper 1 is a detailed characterisation of the reservoirs using a petroleum geochemical approach. Paper 2 describes the application of a single reservoir geochemical screening technique to exploration, appraisal and production geology and reservoir/petroleum engineering. Paper 3 compares the Iatroscan TLC-FID screening technique and the extraction efficiency of micro-extraction used in this work with the well-established Rock-Eval geochemical screening method and with the Soxtec extraction method. Paper 4 refines the migration and filling models of Paper 1, and Paper 5 presents a comparison of models of petroleum generation, migration and accumulation based on geochemical data with 1D burial history, a ''pseudo well'' based on actual well data and regional seismic analysis representing the hydrocarbon generative basin conditions.

Associated petroleum gas in Russia: reasons for non-utilization

Energy Technology Data Exchange (ETDEWEB)

Roeland, Tonje Hulbak

2010-10-22

This report studies the factors hindering increased utilization of associated petroleum gas (APG) in Russia. The issue of flaring versus utilization is studied from a Technology Innovation System (TIS) perspective, seeing the non-utilization issue as a problem of technology diffusion. There are many technological options available for APG utilization, but a main blocking mechanism in the Russian case is the Gazprom monopoly on gas transportation via their pipelines. A commonly discussed solution is policy to ensure third party access, but this study finds that this solution holds little potential, as its ramifications are too extensive and unacceptable to the key actor Gazprom. More promising solutions may be found in small, emerging engineering companies. (Author)

Mechanical engineering

International Nuclear Information System (INIS)

1988-01-01

The Mechanical Engineering Division provides the other NAC divisions with design and construction services. Items of special mechanical significance are discussed here. The projects which received major design attention during the past year were: a coupling capacitor for SPC2; a bending magnet and solenoid for ECR ion source; a scanner for outer orbits of the SSC; a scattering chamber for an experimental beamline; a beam swinger; a rotary target magazine for isotope production; a robot arm for isotope production; an isotope transport system and a target cooling system for isotope production. The major projects that were under construction are: a magnetic spectrometer; a second injector cyclotron (SPC2) and extensions to the high-energy beamlines. 4 figs

Hydro mechanical coupling for non linear behaviour laws. Application to petroleum problems; Couplage hydromecanique pour des lois de comportement non lineaires Application a des problemes petroliers

Energy Technology Data Exchange (ETDEWEB)

Longuemare, P.

1996-11-28

The aim of this study is to provide a better description of the rock contribution to fluid flows in sedimentary basins and petroleum reservoirs. After a study of the mechanical behaviour of high porosity chalks and shales, we present the elaboration of an elastoplastic constitutive model for the description of their behaviour under various strain and stress paths. This model is introduced in a coupled poro-mechanical approach and used to study the advantages of a good description of strain and stress paths in petroleum reservoirs and sedimentary basins studies. Hydro-mechanical modelling of the behaviour of petroleum reservoir allowed us to analyse the influence of boundary limit conditions on stress paths recovery rates. The study of sedimentary basins showed the importance of the consideration of the evolution of the porosity with time due to the time-scale difference between the laboratory and the field data. (author) 58 refs.

Combustion and emission characteristics of a dual fuel engine operated with mahua oil and liquefied petroleum gas

Directory of Open Access Journals (Sweden)

Nadar Kapilan N.

2008-01-01

Full Text Available For the present work, a single cylinder diesel engine was modified to work in dual fuel mode. To study the feasibility of using methyl ester of mahua oil as pilot fuel, it was used as pilot fuel and liquefied petroleum gas was used as primary fuel. In dual fuel mode, pilot fuel quantity and injector opening pressure are the few variables, which affect the performance and emission of dual fuel engine. Hence, in the present work, pilot fuel quantity and injector opening pressure were varied. From the test results, it was observed that the pilot fuel quantity of 5 mg per cycle and injector opening pressure of 200 bar results in higher brake thermal efficiency. Also the exhaust emissions such as smoke, unburnt hydrocarbon and carbon monoxide are lower than other pressures and pilot fuel quantities. The higher injection pressure and proper pilot fuel quantity might have resulted in better atomization, penetration of methyl ester of mahua oil and better combustion of fuel.

Petroleum Science and Technology Institute with the TeXas Earth and Space Science (TXESS) Revolution

Science.gov (United States)

Olson, H. C.; Olson, J. E.; Bryant, S. L.; Lake, L. W.; Bommer, P.; Torres-Verdin, C.; Jablonowski, C.; Willis, M.

2009-12-01

The TeXas Earth and Space Science (TXESS) Revolution, a professional development program for 8th- thru 12th-grade Earth Science teachers, presented a one-week Petroleum Science and Technology Institute at The University of Texas at Austin campus. The summer program was a joint effort between the Jackson School of Geosciences and the Department of Petroleum and Geosystems Engineering. The goal of the institute was to focus on the STEM components involved in the petroleum industry and to introduce teachers to the larger energy resources theme. The institute kicked off with a welcoming event and tour of a green, energy-efficient home (LEED Platinum certified) owned by one of the petroleum engineering faculty. Tours of the home included an introduction to rainwater harvesting, solar energy, sustainable building materials and other topics on energy efficiency. Classroom topics included drilling technology (including a simulator lab and an overview of the history of the technology), energy use and petroleum geology, well-logging technology and interpretation, reservoir engineering and volumetrics (including numerous labs combining chemistry and physics), risk assessment and economics, carbon capture and storage (CO2 sequestration technology) and hydraulic fracturing. A mid-week field trip included visiting the Ocean Star offshore platform in Galveston, the Weiss Energy Hall at the Houston Museum of Science and Schlumberger (to view 3-D visualization technology) in Houston. Teachers remarked that they really appreciated the focused nature of the institute and especially found the increased use of mathematics both a tool for professional growth, as well as a challenge for them to use more math in their science classes. STEM integration was an important feature of the summer institute, and teachers found the integration of science (earth sciences, geophysics), technology, engineering (petroleum, chemical and reservoir) and mathematics particularly valuable. Pre

Geometry of surfaces a practical guide for mechanical engineers

CERN Document Server

Radzevich, Stephen P

2012-01-01

Presents an in-depth analysis of geometry of part surfaces and provides the tools for solving complex engineering problems Geometry of Surfaces: A Practical Guide for Mechanical Engineers is a comprehensive guide to applied geometry of surfaces with focus on practical applications in various areas of mechanical engineering. The book is divided into three parts on Part Surfaces, Geometry of Contact of Part Surfaces and Mapping of the Contacting Part Surfaces. Geometry of Surfaces: A Practical Guide for Mechanical Engineers combines differential geometry and gearing theory and presents new developments in the elementary theory of enveloping surfaces. Written by a leading expert of the field, this book also provides the reader with the tools for solving complex engineering problems in the field of mechanical engineering. Presents an in-depth analysis of geometry of part surfaces Provides tools for solving complex engineering problems in the field of mechanical engineering Combines differential geometry an...

A new and efficient mechanism for spark ignition engines

International Nuclear Information System (INIS)

Shadloo, M.S.; Poultangari, R.; Abdollahzadeh Jamalabadi, M.Y.; Rashidi, M.M.

2015-01-01

Highlights: • A new slider–crank mechanism, with superior performance is presented. • Thermodynamic processes as well as vibration and internal forces have been modeled. • Comparison with the conventional four-stroke spark ignition engines is made. • Advantages and disadvantages of the proposed mechanism are discussed. - Abstract: In this paper a new symmetrical crank and slider mechanism is proposed and a zero dimensional model is utilized to study its combustion performance enhancement in a four-stroke spark ignition (SI) engine. The main features of this new mechanism are superior thermodynamic efficiency, lower internal frictions, and lower pollutants. Comparison is made between its performance and that of the conventional four-stroke SI engines. Presented mechanism is designed to provide better fuel consumption of internal combustion engines. These advantages over standard engine are achieved through synthesis of new mechanism. Numerical calculation have been performed for several cases of different mechanism parameters, compression ratio and engine speed. A comprehensive comparison between their thermodynamic processes as well as vibration and internal forces has been done. Calculated efficiency and power diagrams are plotted and compared with performance of a conventional SI engine. Advantages and disadvantages of the proposed mechanism are discussed in details

Mechanical technology for higher engineering technicians

CERN Document Server

Black, Peter

1972-01-01

Mechanical Technology for Higher Engineering Technicians deals with the mechanics of machines, thermodynamics, and mechanics of fluids. This book presents discussions and examples that deal with the strength of materials, technology of machines, and techniques used by professional engineers. The book explains the strain energy of torsion, coil springs, and the effects of axial load. The author also discusses the forces that produce bending, shearing, and bending combined with direct stress, as well as beams subjected to a uniform bending moment or simply supported beams with concentrated non-c

Mechanical Engineering Department Technical Review

International Nuclear Information System (INIS)

Carr, R.B.; Denney, R.M.

1981-01-01

The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication

PETROLEUM BIOREFINING FOR POLLUTION PREVENTION

Energy Technology Data Exchange (ETDEWEB)

John J. Kilbane II

2002-03-01

The objective of this project was to isolate and characterize thermophilic bacterial cultures that can be used for the selective removal of nitrogen, sulfur, and/or metals in the biorefining of petroleum. The project was completed on schedule and no major difficulties were encountered. Significant progress was made on multiple topics relevant to the development of a petroleum biorefining process capable of operating at thermophilic temperatures. New cultures capable of selectively cleaving C-N or C-S bonds in molecules relevant to petroleum were obtained, and the genes encoding the enzymes for these unique biochemical reactions were cloned and sequenced. Genetic tools were developed that enable the use of Thermus thermophilus as a host to express any gene of interest, and information was obtained regarding the optimum conditions for the growth of T. thermophilus. The development of a practical biorefining process still requires further research and the future research needs identified in this project include the development of new enzymes and pathways for the selective cleavage of C-N or C-S bonds that have higher specific activities, increased substrate range, and are capable of functioning at thermophilic temperatures. Additionally, there is a need for process engineering research to determine the maximum yield of biomass and cloned gene products that can be obtained in fed-batch cultures using T. thermophilus, and to determine the best configuration for a process employing biocatalysts to treat petroleum.

The role of the national petroleum company in petroleum development market

Energy Technology Data Exchange (ETDEWEB)

Lee, B J [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

1997-08-01

The present century started with the creation of national petroleum companies, and it ends with those national petroleum companies exerting various types of efforts to increase the efficiency of their management. Especially, the efforts of these national petroleum companies are ever intensifying to adapt to new trends in the world petroleum market such as intensified competition, ever-deepening price unstableness, separation of structure between upstream and downstream portions, rapid development of petroleum development technologies, change of political systems and the demise of national borders, ever-increasing consciousness of environmental preservation, etc. Korea cannot be exempt from management rationalization efforts of national petroleum companies. Especially, Korea established its own national petroleum company in order to actively deal with these as its supply system is very weak. Therefore, the national petroleum company should create as many successful petroleum development businesses by actively carrying out petroleum development businesses domestically and overseas in order to establish a stable supply system of petroleum and to support the petroleum development businesses of civilian enterprises more effectively. The national petroleum company must, first of all, replace the bureaucracy with entrepreneurship. Esp., in order to enhance the efficiency of management, short- term outcome should not be emphasized over long-term tenure of petroleum development businesses, and excessive interference of government on the national petroleum company should be excluded. The entrepreneurship of the national petroleum company should be pursued in Positive-sum way, and its public image should be actively promoted through this. 35 refs., 11 figs., 32 tabs.

Statistics for Petroleum Engineers and Geoscientists

International Nuclear Information System (INIS)

Jensen, J.L.; Lake, L.W.; Corbett, P.W.M.; Goggin, D.J.

2000-01-01

Geostatistics is a common tool in reservoir characterisation. Several texts discuss the subject, however this book differs in its approach and audience from currently available material. Written from the basics of statistics it covers only those topics that are needed for the two goals of the text: to exhibit the diagnostic potential of statistics and to introduce the important features of statistical modeling. This revised edition contains expanded discussions of some materials, in particular conditional probabilities, Bayes Theorem, correlation, and Kriging. The coverage of estimation, variability, and modeling applications have been updated. Seventy examples illustrate concepts and show the role of geology for providing important information for data analysis and model building. Four reservoir case studies conclude the presentation, illustrating the application and importance of the earlier material. This book can help petroleum professionals develop more accurate models, leading to lower sampling costs

Experiences of a Multidisciplinary Course on Geo-Signal Processing from a DSP Perspective Offered in Electrical Engineering at King Fahd University of Petroleum and Minerals

Science.gov (United States)

Mousa, W. A.

2012-01-01

The purpose of this paper is to share the experience gained in, and the efforts made toward, introducing and implementing a new course in the challenging and important area of geophysical signal processing at the Electrical Engineering (EE) Department, King Fahd University of Petroleum and Minerals (KFUPM), Dhahran, Saudi Arabia. The new course,…

The Purdue Mechanics Freeform Classroom: A New Approach to Engineering Mechanics Education

OpenAIRE

Rhoads, Jeffrey F.; Nauman, Eric; Holloway, Beth M; Krousgrill, Charles Morton

2014-01-01

The [REMOVED] Mechanics Freeform Classroom: A New Approach to Engineering Mechanics EducationMotivated by the need to address the broad spectrum of learning styles embraced by today’sengineering students, a desire to encourage active, peer-to-peer, and self-learning, and a goal ofinteracting with every student despite ever-expanding enrollments, the mechanics faculty at[REMOVED] University have developed the [REMOVED] Mechanics Freeform Classroom(PMFC) -- a new approach to engineering mechani...

Petroleum supply monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Selection of software for mechanical engineering undergraduates

International Nuclear Information System (INIS)

Cheah, C. T.; Yin, C. S.; Halim, T.; Naser, J.; Blicblau, A. S.

2016-01-01

A major problem with the undergraduate mechanical course is the limited exposure of students to software packages coupled with the long learning curve on the existing software packages. This work proposes the use of appropriate software packages for the entire mechanical engineering curriculum to ensure students get sufficient exposure real life design problems. A variety of software packages are highlighted as being suitable for undergraduate work in mechanical engineering, e.g. simultaneous non-linear equations; uncertainty analysis; 3-D modeling software with the FEA; analysis tools for the solution of problems in thermodynamics, fluid mechanics, mechanical system design, and solid mechanics.

Selection of software for mechanical engineering undergraduates

Energy Technology Data Exchange (ETDEWEB)

Cheah, C. T.; Yin, C. S.; Halim, T.; Naser, J.; Blicblau, A. S., E-mail: ablicblau@swin.edu.au [Swinburne University of Technology, Faculty of Science Engineering and Technology, PO Box 218 Hawthorn, Victoria, Australia, 3122 (Australia)

2016-07-12

A major problem with the undergraduate mechanical course is the limited exposure of students to software packages coupled with the long learning curve on the existing software packages. This work proposes the use of appropriate software packages for the entire mechanical engineering curriculum to ensure students get sufficient exposure real life design problems. A variety of software packages are highlighted as being suitable for undergraduate work in mechanical engineering, e.g. simultaneous non-linear equations; uncertainty analysis; 3-D modeling software with the FEA; analysis tools for the solution of problems in thermodynamics, fluid mechanics, mechanical system design, and solid mechanics.

Measure of the volumetric efficiency and evaporator device performance for a liquefied petroleum gas spark ignition engine

International Nuclear Information System (INIS)

Masi, Massimo; Gobbato, Paolo

2012-01-01

Highlights: ► Measure of the effect of LPG fuel on volumetric efficiency of a SI petrol ICE. ► Steady-state and transient performance of a LPG evaporator device on a SI ICE. ► Volume displaced by LPG causes slight performance loss in SI petrol engines. ► LPG reveals peak efficiency and high-efficiency range wider than petrol in SI ICE’s. ► One-stage pressure reducer for LPG performs satisfactorily during SI ICE transients. - Abstract: The use of Liquefied Petroleum Gas (LPG) as fuel for spark ignition engines originally designed to be gasoline fuelled is common practice in many countries. Despite this, some questions remain still open. The present paper deals with the two main problems related to LPG port-fuel SI engines: the volumetric efficiency drop and the LPG evaporator device performance. A passengers car SI engine equipped with a “third generation” kit for the dual-fuel operation was tested using a dynamometer test rig. A single-stage pressure reducer was selected as LPG evaporator, to take advantage of an additional pre-heating of the liquid LPG that allows higher power output than a two-stage device of the same size. Engine performance, volumetric efficiency and change of LPG thermodynamic states in the evaporator were measured both in steady-state and transient operation of the engine. Steady-state measurements show the advantage of LPG in terms of engine efficiency, and quantify the drop in steady-state brake torque due to the volume swept by gaseous fuel in the fresh charge admission process. On the other hand, transient measurements show that a single-stage evaporator device is capable to match overall simplicity and satisfactory performance during strong changes in engine load.

Gasoline Engine Mechanics. Florida Vocational Program Guide.

Science.gov (United States)

University of South Florida, Tampa. Dept. of Adult and Vocational Education.

This vocational program guide is intended to assist in the organization, operation, and evaluation of a program in gasoline engine mechanics in school districts, area vocational centers, and community colleges. The following topics are covered: job duties of small-engine mechanics; program content (curriculum framework and student performance…

Impact of petroleum products on soil composition and physical-chemical properties

Science.gov (United States)

Brakorenko, N. N.; Korotchenko, T. V.

2016-03-01

The article describes the grain-size distribution, physical and mechanical properties, swelling and specific electrical resistivity of soils before and after the contact with petroleum products. The changes in mechanical properties of soils contaminated with petroleum products have been stated. It leads to the increase in compressibility values, decline in internal friction angle and cohesion.

Impact of petroleum products on soil composition and physical-chemical properties

OpenAIRE

Brakorenko, Nataliya Nikolaevna; Korotchenko, Tatiana Valerievna

2016-01-01

The article describes the grain-size distribution, physical and mechanical properties, swelling and specific electrical resistivity of soils before and after the contact with petroleum products. The changes in mechanical properties of soils contaminated with petroleum products have been stated. It leads to the increase in compressibility values, decline in internal friction angle and cohesion.

International Conference on Research and Innovations in Mechanical Engineering

CERN Document Server

Singh, Paramjit; Singh, Harwinder; Brar, Gurinder

2014-01-01

This book comprises the proceedings of International Conference on Research and Innovations in Mechanical Engineering (ICRIME 2013) organized by Guru Nanak Dev Engineering College, Ludhiana with support from AICTE, TEQIP, DST and PTU, Jalandhar. This international conference served as a premier forum for communication of new advances and research results in the fields of mechanical engineering. The proceedings reflect the conference’s emphasis on strong methodological approaches and focus on applications within the domain of mechanical engineering. The contents of this volume aim to highlight new theoretical and experimental findings in the fields of mechanical engineering and closely related fields, including interdisciplinary fields such as robotics and mechatronics.

Crude petroleum

International Nuclear Information System (INIS)

1990-01-01

Crude petroleum statistics by country of production, export values and import values from 1983 to 1988 are given. Table A.1 of the Annex includes free market prices and price indices for crude petroleum based on average of Dubai, United Kingdom Brent and Alaska N Slope crude prices (price expressed in dollars/barrel). The data sources are: Crude petroleum United Nations Statistical Office; OPEC Annual Statistical Bulletin, and Petroleum Economist. For trade the sources of data are: National trade statistics; United Nations international trade statistics; International Moneytary Fund (IMF); Organization of the Petroleum Exporting Countries (OPEC); UNCTAD secretariat estimates. Tabs

Proceedings of the Canadian International Petroleum Conference 2005 and the 56. Annual Technical Meeting of the Petroleum Society of CIM : Because Technology Changes Everything. CD ed.

International Nuclear Information System (INIS)

2005-01-01

This conference and trade show outlined the latest technologies associated with hydrocarbon exploration, petroleum geology, resource development, and enhanced recovery. It was attended by local and international participants in the petroleum sector. The 31 sessions highlighted the challenges facing the petroleum industry in terms of maturing basins and focused on issues such as business development and risk management; cold production of heavy oil; health, safety and regulatory issues; and environmental concerns regarding oil and gas development. The presentations were targeted for managers, engineers, technologists, geologists, and other petroleum industry specialists dealing with topical issues such as: well completion; well stimulation; well test analysis; thermal recovery; reservoir characterization; fluid characterization; numerical simulation; computerized simulation; emerging technology; thermal field projects; production operations; business development; and refining facilities. A total of 122 papers have been catalogued separately for inclusion in this database. (author)

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are gathered the results of the year 1999 concerning the petroleum industry in France ('UFIP' data), the market quotations of crude oil, the prices of fuels in France and in Portugal and some news about the petroleum industry in Algeria (privatization, exploration-offshore, repurchase), in Iraq (exports, contracts with foreign companies), in Russian Federation (petroleum pipelines and oil ports constructions) and in Chad (production sharing, offshore sites discoveries). (O.M.)

Petroleum Supply Monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Basic Mechanics with Engineering Applications

CERN Document Server

Jones, J; Fawcett, J N

2012-01-01

This book gives a sufficient grounding in mechanics for engineers to tackle a significant range of problems encountered in the design and specification of simple structures and machines. It also provides an excellent background for students wishing to progress to more advanced studies in three-dimensional mechanics.

Mechanical engineers' handbook, design, instrumentation, and controls

CERN Document Server

Kutz, Myer

2015-01-01

Full coverage of electronics, MEMS, and instrumentation andcontrol in mechanical engineering This second volume of Mechanical Engineers' Handbookcovers electronics, MEMS, and instrumentation and control, givingyou accessible and in-depth access to the topics you'll encounterin the discipline: computer-aided design, product design formanufacturing and assembly, design optimization, total qualitymanagement in mechanical system design, reliability in themechanical design process for sustainability, life-cycle design,design for remanufacturing processes, signal processing, dataacquisition and dis

Condition and prospects of development of agricultural mechanical engineering

OpenAIRE

Vsevolod Babushkin; Margarita Ignatyeva

2011-01-01

In this paper, an estimation of condition and level of development of agricultural mechanical engineering is given; also an expert estimation of scales of the Russian market of agricultural machinery is given. The factors negatively influencing formation of the named market are designated. Features and prospects of development of agricultural mechanical engineering of Sverdlovsk region are defined. State regulation mechanisms of domestic agricultural mechanical engineering development are des...

The energy policy and sustainability of the subsidy mechanism for retail petroleum products consumed in Trinidad and Tobago

Energy Technology Data Exchange (ETDEWEB)

Baksh, Timmy

2010-09-15

In 1974 the Petroleum Production Levy and Subsidy Act gave effect to legislation which detailed a mechanism to implement a subsidy on all fuel consumed within, and in the territorial waters of, Trinidad and Tobago. This paper will analyse the underlying principles of this energy policy, follow how the mechanism has evolved over the years and propose new iterations to the existing model in order to reduce the Governments liability. The sustainability of the subsidy will be examined and as well as an in-depth analysis on the possible impact on inflation if this mechanism is removed.

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are briefly summarized 1)the OPEC decisions and their consequences concerning the production of petroleum in the world 2)some news about the petroleum industry in Chad and in Iraq 3)some news about the new pipelines constructed or to be constructed in the world 4)some news about the LPG industry (start of a LPG extraction unit in Argentina, legislation in France for LPG vehicles) 4)and some news about the petroleum distribution in France. (O.M.)

Bureau Veritas: 1995 realizations in the petroleum domain

International Nuclear Information System (INIS)

Anon.

1996-01-01

The completion of the Bureau Veritas (BV) company reorganization in France led to a stabilization of its main activities which fall into five engineering domains: sea service, building and exploitation safety, industry, international trade, aeronautics. The petroleum industry remains a great consumer of the offshore and onshore services provided by this company worldwide. This short paper briefly describes some recent contracts signed between BV and famous petroleum and service companies for the inspection and the safety analyses of industrial materials devoted to offshore exploitation, drilling and lodging, of gas transportation and storage systems (pipelines, reservoirs, tankers), and for the research and development studies related to deep-sea operations. (J.S.)

The world economy of petroleum products and the strategy of a petroleum company from exporting country: Cases of SONATRACH (Algeria), KPC (Kuwait), PEMEX (Mexico), PDVSA (Venezuela). Second volume

International Nuclear Information System (INIS)

Preure, M.

1992-12-01

This thesis contains 2 volumes. In this second volume, the author describes the industrial and technological developments and the strategy of petroleum companies in exporting countries. The main industrial strategies studied are national integration strategy in a planned economy (case of Algeria) or in a controlled-liberal economy (case of Mexico) and international integration strategies to the lower part of petroleum industry and external growth (cases of Kuwait and Venezuela). Technological strategies studied are development of a national engineering, information, research programs/ development and innovation. The last chapter takes stock of research and development programs for petroleum products (case of Mexico) . 258 refs., 103 tabs

Shell petroleum handbook. [Glossary included

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

The present edition has been completely updated and revised, reflecting the very great changes which have come about in the oil industry over the last 18 years, since the last edition appeared. The expressed aim of the Handbook is to combine explanations of the processes of today's petroleum industry, from crude oil exploration to product end-use, with some historical background and explanation of the economic context in which the oil, gas and petrochemical industries operate. It is therefore intended as a technical reference manual, although it will be of interest both to specialists in search of information outside their expertise and to the more general reader. Chapter 3, entitled Exploration and Production, is concerned with structural geology, exploration methods and theory, and reservoir engineering, although the economic and financial aspects of drilling, project management and communication logistics are also considered. Other chapters are devoted to the distribution, consumption and end use of natural gas and NGL, the chemistry of petroleum, the manufacture of oil products, marketing, supply and trading, petrochemicals, synfuels, R and D, environmental conservation, and introduction to the world petroleum industry, and a review of oil and gas in the centrally planned economies, although only the Soviet Union is considered in any detail.

46 CFR 113.35-15 - Mechanical engine order telegraph systems; application.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Mechanical engine order telegraph systems; application...) ELECTRICAL ENGINEERING COMMUNICATION AND ALARM SYSTEMS AND EQUIPMENT Engine Order Telegraph Systems § 113.35-15 Mechanical engine order telegraph systems; application. If a mechanical engine order telegraph...

Vermiremediation of soils contaminated with mixture of petroleum ...

African Journals Online (AJOL)

In this paper, vermiremediation, a biological technique was utilized in order to clean-up soil contaminated with gasoline, diesel and spent engine oil using an earthworm - Eisenia fetida. The contaminated soils were analyzed for the total petroleum hydrocarbon (TPH) level every 24 hours over a period of 120 hours using ...

Biodegradation and chemical characterization of petroleum diesel hydrocarbons in seawater at low temperatures

OpenAIRE

Bausch, Alexandre Renee

2010-01-01

Master's thesis in Environmental engineering Petroleum hydrocarbons are a major source of marine contamination. Biodegradation, which is fundamental for the natural attenuation of these hydrocarbons in nature, involves mineralization or transformation of organic compounds by autochthonous microorganism communities. Various limiting factors characteristic of the petroleum, the external environment, and the microbial community determine the fate of oil (e.g., diesel) in the marine environmen...

Proceedings of the Go-Expo Gas and Oil Exposition and the 4. Annual Canadian International Petroleum Conference and the 54. Annual Technical Meeting of the Petroleum Society of CIM : Global Challenges and Technology Integration. CD-ROM ed.

International Nuclear Information System (INIS)

2003-01-01

A series of technical papers dealing with various aspects of petroleum geology and resource development were presented at this conference and trade show which was attended by local and international participants. The 27 sessions reflected the changes facing the petroleum industry in terms of fluctuating product prices, aging staff, maturing basins, frontier development, and environmental concerns. The conference is truly international with nearly one third of the 250 presentations coming from outside of Canada. The presentations were targeted for managers, engineers, technologists, geologists, and other petroleum industry specialists dealing with issues such as: business development; conventional oil and gas recovery; conventional and unconventional heavy oil recovery; corrosion, pipelines and process engineering; drilling engineering; enhanced recovery; environmental management; production operations; regulatory and operations management; reservoir fluid characterization; reservoir simulation; risk management; well test analysis; and, well design and completions. A total of 124 papers have been processed separately for inclusion in this database. refs., tabs., figs

Welcoming speech from Dean Faculty of Mechanical Engineering, UMP

Science.gov (United States)

Taha, Zahari

2012-09-01

In the Name of Allah, the Most Beneficent, the Most Merciful. It is with great pleasure that I welcome the participants of the International Conference of Mechanical Engineering Research 2011. The Prophet Muhammad (peace be upon him) said 'Acquire knowledge and impart it to the people.' (Al Tirmidhi). The quest for knowledge has been from the beginning of time but knowledge only becomes valuable when it is disseminated and applied to benefit humankind. It is hoped that ICMER 2011 will be a platform to gather and disseminate the latest knowledge in mechanical engineering. Academicians, Scientist, Researchers and practitioners of mechanical engineering will be able to share and discuss new findings and applications of mechanical engineering. It is envisaged that the intellectual discourse will result in future collaborations between universities, research institutions and industry both locally and internationally. In particular it is expected that focus will be given to issues on environmental and energy sustainability. Researchers in the mechanical engineering faculty at UMP have a keen interest in technology to harness energy from the ocean. Lowering vehicle emissions has been a primary goal of researchers in the mechanical engineering faculty and the automotive engineering centre as well including developing vehicles using alternative fuels such as biodiesel and renewable sources such as solar driven electric vehicles. Finally I would like to congratulate the organizing committee for their tremendous efforts in organizing the conference. As I wrote this in the Holy Land of Makkah, I pray to Allah swt that the conference will be a success. Prof. Dr. Zahari Taha CEng, MIED, FASc Dean, Faculty of Mechanical Engineering Universiti Malaysia Pahang

Optimization of a relativistic quantum mechanical engine.

Science.gov (United States)

Peña, Francisco J; Ferré, Michel; Orellana, P A; Rojas, René G; Vargas, P

2016-08-01

We present an optimal analysis for a quantum mechanical engine working between two energy baths within the framework of relativistic quantum mechanics, adopting a first-order correction. This quantum mechanical engine, with the direct energy leakage between the energy baths, consists of two adiabatic and two isoenergetic processes and uses a three-level system of two noninteracting fermions as its working substance. Assuming that the potential wall moves at a finite speed, we derive the expression of power output and, in particular, reproduce the expression for the efficiency at maximum power.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Association of engineering geologists 32nd annual meeting

International Nuclear Information System (INIS)

Anon.

1989-01-01

This book contains the proceedings of the 32nd Annual Meeting of the Association of Engineering Geologists. Included are the following articles: Engineering geology---a tool in petroleum exploration ventures font, The soil headspace survey method as an indicator of soil and groundwater contamination by petroleum products, Determination of compressive strength of coal for pillar design hirt

Petroleum 2006. Statistical elements

International Nuclear Information System (INIS)

2007-06-01

This document gathers in 5 parts, the main existing statistical data about petroleum industry in France and in the rest of the world, together with an insight on other energy sources: 1 - petroleum in the French economy (petroleum and other energies, petroleum and transports, petroleum and energy in the industry, the residential and tertiary sectors, environment: 42 pages); 2 - the French petroleum industry (exploration, production, foreign trade, transports, refining, storage, petrochemistry: 66 pages); 3 - the French market of petroleum products (evolution of sales by product and detail by region for the past year: 38 pages); 4 - prices and taxes of petroleum products (world prices and rates for crude and refined products, evolution of fret rates, retail prices and French taxes: 28 pages); 5 - petroleum in the world (world energy production and consumption, detailed petroleum activity by main areas and for the main countries: 112 pages). (J.S.)

Quantum Mechanics for Electrical Engineers

CERN Document Server

Sullivan, Dennis M

2011-01-01

The main topic of this book is quantum mechanics, as the title indicates.  It specifically targets those topics within quantum mechanics that are needed to understand modern semiconductor theory.   It begins with the motivation for quantum mechanics and why classical physics fails when dealing with very small particles and small dimensions.  Two key features make this book different from others on quantum mechanics, even those usually intended for engineers:   First, after a brief introduction, much of the development is through Fourier theory, a topic that is at

Recent Advances in Petroleum Microbiology

Science.gov (United States)

Van Hamme, Jonathan D.; Singh, Ajay; Ward, Owen P.

2003-01-01

Recent advances in molecular biology have extended our understanding of the metabolic processes related to microbial transformation of petroleum hydrocarbons. The physiological responses of microorganisms to the presence of hydrocarbons, including cell surface alterations and adaptive mechanisms for uptake and efflux of these substrates, have been characterized. New molecular techniques have enhanced our ability to investigate the dynamics of microbial communities in petroleum-impacted ecosystems. By establishing conditions which maximize rates and extents of microbial growth, hydrocarbon access, and transformation, highly accelerated and bioreactor-based petroleum waste degradation processes have been implemented. Biofilters capable of removing and biodegrading volatile petroleum contaminants in air streams with short substrate-microbe contact times (desulfurization processes with biodesulfurization methods through promotion of selective sulfur removal without degradation of associated carbon moieties. However, since microbes require an environment containing some water, a two-phase oil-water system must be established to optimize contact between the microbes and the hydrocarbon, and such an emulsion is not easily created with viscous crude oil. This challenge may be circumvented by application of the technology to more refined gasoline and diesel substrates, where aqueous-hydrocarbon emulsions are more easily generated. Molecular approaches are being used to broaden the substrate specificity and increase the rates and extents of desulfurization. Bacterial processes are being commercialized for removal of H2S and sulfoxides from petrochemical waste streams. Microbes also have potential for use in removal of nitrogen from crude oil leading to reduced nitric oxide emissions provided that technical problems similar to those experienced in biodesulfurization can be solved. Enzymes are being exploited to produce added-value products from petroleum substrates, and

46 CFR 113.35-9 - Mechanical engine order telegraph systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Mechanical engine order telegraph systems. 113.35-9 Section 113.35-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING COMMUNICATION AND ALARM SYSTEMS AND EQUIPMENT Engine Order Telegraph Systems § 113.35-9 Mechanical engine order...

PETROLEUM-COLLECTING AND DISPERSING CHEMICALS FOR ...

African Journals Online (AJOL)

Preferred Customer

Films of petroleum origin reflecting sunlight rays hinder absorption of energy by water necessary for life ... Dispersing chemicals like mechanical clean-up methods have their own place in fighting oil spills. They are ... yellow color, and filtered.

Thermal integrity in mechanics and engineering

CERN Document Server

Shorr, Boris F

2015-01-01

The book is targeted at engineers, university lecturers, postgraduates, and final year undergraduate students involved in computational modelling and experimental and theoretical analysis of the high-temperature behavior of engineering structures. It will also be of interest to researchers developing the thermal strength theory as a branch of continuum mechanics. Thermal integrity is a multidisciplinary field combining the expertise of mechanical engineers, material scientists and applied mathematicians, each approaching the problem from their specific viewpoint. This monograph draws on the research of a broad scientific community including the author’s contribution. The scope of thermal strength analysis was considerably extended thanks to modern computers and the implementation of FEM codes. However, the author believes that some material models adopted in the advanced high-performance software, are not sufficiently justificated due to lack of easy-to-follow books on the theoretical and experimental aspec...

Engineering a General Education Program: Designing Mechanical Engineering General Education Courses

Science.gov (United States)

Fagette, Paul; Chen, Shih-Jiun; Baran, George R.; Samuel, Solomon P.; Kiani, Mohammad F.

2013-01-01

The Department of Mechanical Engineering at our institution created two engineering courses for the General Education Program that count towards second level general science credit (traditional science courses are first level). The courses were designed for the general student population based upon the requirements of our General Education Program…

The role of mechanical loading in ligament tissue engineering.

Science.gov (United States)

Benhardt, Hugh A; Cosgriff-Hernandez, Elizabeth M

2009-12-01

Tissue-engineered ligaments have received growing interest as a promising alternative for ligament reconstruction when traditional transplants are unavailable or fail. Mechanical stimulation was recently identified as a critical component in engineering load-bearing tissues. It is well established that living tissue responds to altered loads through endogenous changes in cellular behavior, tissue organization, and bulk mechanical properties. Without the appropriate biomechanical cues, new tissue formation lacks the necessary collagenous organization and alignment for sufficient load-bearing capacity. Therefore, tissue engineers utilize mechanical conditioning to guide tissue remodeling and improve the performance of ligament grafts. This review provides a comparative analysis of the response of ligament and tendon fibroblasts to mechanical loading in current bioreactor studies. The differential effect of mechanical stimulation on cellular processes such as protease production, matrix protein synthesis, and cell proliferation is examined in the context of tissue engineering design.

Overview of soil and groundwater research activities of the American Petroleum Institute (API)

International Nuclear Information System (INIS)

Bauman, B.

1992-01-01

The American Petroleum Institute (API) is a trade association for the domestic petroleum industry in the USA, with over 2000 corporate and 5000 individual members. Subsurface research activities are managed by the API soil/groundwater technical task force, a committee made up of over 25 member company engineers, hydrologists, soil scientists, and chemists representing both the research and operations sectors of the petroleum industry. The research areas of the group have been divided into five principle areas: biodegradation processes, fate and transport, remediation, decision making tools for remediation, and detection/analytical methods. A summary of each of the current projects in these subject areas is presented

Petroleum fiscality indicators

International Nuclear Information System (INIS)

2008-02-01

This document presents the different taxes imposed to petroleum products in France: domestic tax on petroleum products (TIPP) and added value tax (TVA). A comparison is made with the fiscality into effect in other European countries for some petroleum products. Then, the fiscality is detailed for the different petroleum products and automotive fuels with its regional modulations. Finally, the fiscal measures adopted in 2007 are detailed. They concern the transposition of the European directive 2003-96/CE into French right and some fiscal regime changes given to some economical sectors particularly penalized by the rise of petroleum energy prices in 2007. (J.S.)

Petroleum industry 1996

International Nuclear Information System (INIS)

1997-01-01

A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector's companies (oil groups, para-petroleum French industry, scientific and technical research)

Mechanics of materials formulas and problems : engineering mechanics 2

CERN Document Server

Gross, Dietmar; Wriggers, Peter; Schröder, Jörg; Müller, Ralf

2017-01-01

This book contains the most important formulas and more than 140 completely solved problems from Mechanics of Materials and Hydrostatics. It provides engineering students material to improve their skills and helps to gain experience in solving engineering problems. Particular emphasis is placed on finding the solution path and formulating the basic equations. Topics include: - Stress - Strain - Hooke’s Law - Tension and Compression in Bars - Bending of Beams - Torsion - Energy Methods - Buckling of Bars - Hydrostatics .

Petroleum industry in 2004

International Nuclear Information System (INIS)

2005-01-01

This document presents a detailed outlook of the petroleum industry in the world and more particularly in France in 2005: evolution of crude oil prices; petroleum exploration and production in the world and in France; the French para-petroleum and petroleum industry; the oil supplies; the refining activities; the evolution of products quality and the substitution fuels; the domestic transports, the storage and consumption of petroleum products; the fiscality, prices and distribution of petroleum products. (J.S.)

19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

International Conference on Mechanical Engineering and Technology

CERN Document Server

Mechanical Engineering and Technology

2012-01-01

The volume includes a set of selected papers extended and revised from the 2011 International Conference on Mechanical Engineering and Technology, held on London, UK, November 24-25, 2011.   Mechanical engineering technology is the application of physical principles and current technological developments to the creation of useful machinery and operation design. Technologies such as solid models may be used as the basis for finite element analysis (FEA) and / or computational fluid dynamics (CFD) of the design. Through the application of computer-aided manufacturing (CAM), the models may also be used directly by software to create "instructions" for the manufacture of objects represented by the models, through computer numerically controlled (CNC) machining or other automated processes, without the need for intermediate drawings.   This volume covers the subject areas of mechanical engineering and technology, and also covers interdisciplinary subject areas of computers, communications, control and automation...

Mechanical engineers' handbook, manufacturing and management

CERN Document Server

Kutz, Myer

2015-01-01

Full coverage of manufacturing and management in mechanicalengineering Mechanical Engineers' Handbook, Fourth Edition provides aquick guide to specialized areas that engineers may encounter intheir work, providing access to the basics of each and pointingtoward trusted resources for further reading, if needed. The book'saccessible information offers discussions, examples, and analysesof the topics covered, rather than the straight data, formulas, andcalculations found in other handbooks. No single engineer can be aspecialist in all areas that they are called upon to work in. It'sa discipline

Mechanical Engineering Senior Design Project Final Presentations | College

Science.gov (United States)

Engineering Research Computational Mechanics Laboratory Environmental Engineering Laboratory Geotechnical of Engineering & Applied Science A B C D E F G H I J K L M N O P Q R S T U V W X Y Z D2L Programs Concentration in Biomedical Engineering Concentration on Ergonomics M.S. Program in Computer

Characterization of crude oils and petroleum products: (I Elution liquid chromatographic separation and gas chromatographic analysis of crude oils and petroleum products

Directory of Open Access Journals (Sweden)

E.O. Odebunmi

2002-12-01

Full Text Available Some physical and chemical properties of samples of light, medium and heavy Nigerian crude oils and petroleum products including gasoline, kerosene and engine oil have been measured and are reported in this paper. The crude oils and petroleum products have also been characterized by fractional distillation and elution liquid chromatography. The fractions obtained from elution liquid chromatography were analyzed using gas chromatography (GC. The GC fractions were identified by comparing the retention time of peaks in the unknown samples with those of components of calibration standard mixtures. The importance of the physico-chemical properties and the significance of the fractional distillation and chromatographic separation methods to industrial process operations have been discussed.

The petroleum industry in 2003

International Nuclear Information System (INIS)

2004-01-01

This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-11-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

Estimating air emissions from a remediation of a petroleum sump using direct measurement and modeling

International Nuclear Information System (INIS)

Schmidt, C.E.

1991-01-01

A technical approach was developed for the remediation of a petroleum sump near a residential neighborhood. The approach evolved around sludge handling/in-situ solidification and on-site disposal. As part of the development of the engineering approach, a field investigation and modeling program was conducted to predict air emissions from the proposed remediation. Field measurements using the EPA recommended surface isolation flux chamber were conducted to represent each major activity or air exposure involving waste at the site. Air emissions from freshly disturbed petroleum waste, along with engineering estimates were used to predict emissions from each phase of the engineering approach. This paper presents the remedial approach and the measurement/modeling technologies used to predict air toxic emissions from the remediation. Emphasis will be placed on the measurement approaches used in obtaining the emission rate data and the assumptions used in the modeling to estimate emissions from engineering scenarios

Application of Modern Simulation Technology in Mechanical Outstanding Engineer Training

Directory of Open Access Journals (Sweden)

Gongfa Li

2014-03-01

Full Text Available This text has described the relationship between outstanding engineer training and modern simulation technology, have recommended the characteristics of mechanical outstanding engineer in detail. Aiming at the importance of the teaching practice link to course of theory of mechanics, mechanical design and mechanical signal analysis, have expounded the function of modern simulation technology in the mechanical outstanding engineer training, especially on teaching practice in the theory of mechanics, mechanical design and mechanical signal analysis. It has the advantages of economizing the teaching cost, overcoming the hardware constrains, model prediction, promoting student's innovation and manipulative ability, so can popularize and develop in a more cost-effective manner in the university.

Experimental investigations of LPG use at the automotive diesel engine

Directory of Open Access Journals (Sweden)

Nutu Cristian

2017-01-01

Full Text Available The liquefied petroleum gas has a great potential to improve energetically and pollution performance of compression ignition engines due to its good combustion properties. This paper presents results of the researches carried on a car compression ignition engine with a 1.5 dm3 displacement, fuelled with diesel fuel and liquefied petroleum gas by diesel-gas method at the operating regimens of 70% and 55% engine load, engine speed of 2000 rpm and for substitute ratios between (6–19%. A specific objective of this paper is to establish a correlation between the optimum adjustments and the substitute ratio of the diesel fuel with liquefied petroleum gas for the investigated regimens to limit the maximum pressure and smoke level, knock and rough engine functioning and having regard to decrease the fuel consumption and the level of the pollutant emissions.

Petroleum software profiles

International Nuclear Information System (INIS)

Anon.

1996-01-01

A profile of twenty-two software packages designed for petroleum exploration and production was provided. Some focussed on the oil and gas engineering industry, and others on mapping systems containing well history files and well data summaries. Still other programs provided accounting systems designed to address the complexities of the oil and gas industry. The software packages reviewed were developed by some of the best-known groups involved in software development for the oil and gas industry, including among others, Geoquest, the Can Tek Group, Applied Terravision Systems Inc., Neotechnology Consultants Ltd., (12) OGCI Software Inc., Oracle Energy, Production Revenue Information Systems Management, Virtual Computing Services Ltd., and geoLogic Systems Ltd

Mechanical Properties and Acoustic Emission Properties of Rocks with Different Transverse Scales

OpenAIRE

Yan, Xi; Jun, Li; Gonghui, Liu; Xueli, Guo

2017-01-01

Since the stability of engineering rock masses has important practical significance to projects like mining, tunneling, and petroleum engineering, it is necessary to study mechanical properties and stability prediction methods for rocks, cementing materials that are composed of minerals in all shapes and sizes. Rocks will generate acoustic emission during damage failure processes, which is deemed as an effective means of monitoring the stability of coal rocks. In the meantime, actual mining a...

The para-petroleum industry. International context and results of the 2005 French inquiry

International Nuclear Information System (INIS)

Bensaid, B.; Sagary, C.; Saniere, A.

2005-01-01

Oil companies rarely carry out themselves the important works planned in the framework of their investments or of the exploitation of their facilities. In most cases, they act as prime contractor and generate a huge market of equipments, services and engineering needs in which many companies of various size are involved and make the overall para-petroleum industry. The French position on this market was asserted very early thanks to the continuation of ambitious R and D programs, very often carried out in the framework of the CEP and M and of the COPREP, which have permitted to build and maintain a solid technological knowledge. In this context, the lack of regular statistical data about the French para-petroleum industry has led, since 1978, the group of para-petroleum and para-gas companies, the CEP and M and the former COPREP (now the Committee of petroleum and marine studies - CEP and M), and the French institute of petroleum (IFP), to launch an annual inquiry at the national scale. This document makes a brief overview of the international context of the petroleum industry and then presents the last results of the 2004 inquiry about the French para-petroleum industry. Some data are foreseen for 2005, based on the estimations supplied by the companies themselves. (J.S.)

Engineering mechanical microenvironment of macrophage and its biomedical applications.

Science.gov (United States)

Li, Jing; Li, Yuhui; Gao, Bin; Qin, Chuanguang; He, Yining; Xu, Feng; Yang, Hui; Lin, Min

2018-03-01

Macrophages are the most plastic cells in the hematopoietic system and can be widely found in almost all tissues. Recently studies have shown that mechanical cues (e.g., matrix stiffness and stress/strain) can significantly affect macrophage behaviors. Although existing reviews on the physical and mechanical cues that regulate the macrophage's phenotype are available, engineering mechanical microenvironment of macrophages in vitro as well as a comprehensive overview and prospects for their biomedical applications (e.g., tissue engineering and immunotherapy) has yet to be summarized. Thus, this review provides an overview on the existing methods for engineering mechanical microenvironment of macrophages in vitro and then a section on their biomedical applications and further perspectives are presented.

Mechanics, Models and Methods in Civil Engineering

CERN Document Server

Maceri, Franco

2012-01-01

„Mechanics, Models and Methods in Civil Engineering” collects leading papers dealing with actual Civil Engineering problems. The approach is in the line of the Italian-French school and therefore deeply couples mechanics and mathematics creating new predictive theories, enhancing clarity in understanding, and improving effectiveness in applications. The authors of the contributions collected here belong to the Lagrange Laboratory, an European Research Network active since many years. This book will be of a major interest for the reader aware of modern Civil Engineering.

Elements of theoretical mechanics for electronic engineers

CERN Document Server

Bultot, Franz

1965-01-01

Elements of Theoretical Mechanics for Electronic Engineers deals with theoretical mechanics, which is considered one of the fundamental branches of instruction essential to training an engineer. This book discusses the oscillatory motions and their counterparts in electrical circuits and radio, and provides an introduction to differential operators of vector field theory. Other topics covered include systems and functions of vectors; dynamics of a free point; vibrations and waves; and statics. Worked examples and many notes on the application of most sections of the theories to electrical deve

46 CFR 113.35-13 - Mechanical engine order telegraph systems; operation.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Mechanical engine order telegraph systems; operation...) ELECTRICAL ENGINEERING COMMUNICATION AND ALARM SYSTEMS AND EQUIPMENT Engine Order Telegraph Systems § 113.35-13 Mechanical engine order telegraph systems; operation. If more than one transmitter operates a...

Proceedings of the 3. Canada-US rock mechanics symposium and 20. Canadian rock mechanics symposium : rock engineering 2009 : rock engineering in difficult conditions

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference provided a forum for geologists, mining operators and engineers to discuss the application of rock mechanics in engineering designs. Members of the scientific and engineering communities discussed challenges and interdisciplinary elements involved in rock engineering. New geological models and methods of characterizing rock masses and ground conditions in underground engineering projects were discussed along with excavation and mining methods. Papers presented at the conference discussed the role of rock mechanics in forensic engineering. Geophysics, geomechanics, and risk-based approaches to rock engineering designs were reviewed. Issues related to high pressure and high flow water conditions were discussed, and new rock physics models designed to enhance hydrocarbon recovery were presented. The conference featured 84 presentations, of which 9 have been catalogued separately for inclusion in this database. tabs., figs.

Earthworm-assisted bioremediation of petroleum hydrocarbon ...

African Journals Online (AJOL)

Ameh

The use of earthworms (Eudrilus eugenia) for vermi-assisted bioremediation of petroleum hydrocarbon contaminated mechanic workshop soils ... not always result in complete neutrali- zation of pollutants (Yerushalmi et al., 2003). ..... Screening of biofouling activity in marine bacterial isolate from ship hull. Int. J. Environ. Sci.

Engineering cell factories for producing building block chemicals for bio-polymer synthesis.

Science.gov (United States)

Tsuge, Yota; Kawaguchi, Hideo; Sasaki, Kengo; Kondo, Akihiko

2016-01-21

Synthetic polymers are widely used in daily life. Due to increasing environmental concerns related to global warming and the depletion of oil reserves, the development of microbial-based fermentation processes for the production of polymer building block chemicals from renewable resources is desirable to replace current petroleum-based methods. To this end, strains that efficiently produce the target chemicals at high yields and productivity are needed. Recent advances in metabolic engineering have enabled the biosynthesis of polymer compounds at high yield and productivities by governing the carbon flux towards the target chemicals. Using these methods, microbial strains have been engineered to produce monomer chemicals for replacing traditional petroleum-derived aliphatic polymers. These developments also raise the possibility of microbial production of aromatic chemicals for synthesizing high-performance polymers with desirable properties, such as ultraviolet absorbance, high thermal resistance, and mechanical strength. In the present review, we summarize recent progress in metabolic engineering approaches to optimize microbial strains for producing building blocks to synthesize aliphatic and high-performance aromatic polymers.

The petroleum industry in 2005

International Nuclear Information System (INIS)

2006-01-01

This document provides information on the petroleum industry for the year 2005. It discusses the world gas and petroleum markets, the world and french petroleum exploration and production, the petroleum and byproducts industry in France, the hydrocarbons supplying, the refining in France, the evolution of the products and fuels substitution quality, the internal transports of petroleum products, the storage consumption and taxes of petroleum products, the prices and distribution of the petroleum products. (A.L.B.)

International petroleum enviromental conference (IPEC) offers opportunity for exchange of ideas

International Nuclear Information System (INIS)

Veil, J.A.; Spiric, Z.

2001-01-01

Oil and gas are produced in many parts of the world. Persons working in the petroleum industry can learn much by communicating with colleagues in other countries, but the opportunities for engineers and scientists to come together and discuss petroleum environmental control practices, technologies, and regulations with representatives of other countries are limited. This paper describes the very useful International Petroleum Environmental Conference (IPEC) which completed its seventh meeting in November 2000 in Albuquerque, New Mexico, USA. The 7th IPEC attracted 350 participants, including 26 participants from countries other than the United States. The 7th IPEC emphasized international issues and included more than 20 papers by international authors or on international topics. The conference covered all aspects of petroleum environmental issues and featured speakers from many disciplines. The conference included technical sessions on the following topics: Legal and Regulatory Issues in the Oil and Gas Industry; Pollution Prevention, Waste Management, and Waste Minimization; Bioremediation of Petroleum Hydrocarbons; Characterization and Remediation of Brine-Impacted Soils; Biotreatment and Bioremediation; International Issues in the Oil and Gas Industry; Phytoremediation of Petroleum Hydrocarbons; Treatment and Management of Produced Water; Forensic Geochemistry and Site Characterization/Technology Transfer; Environmentall Acceptable Endpoints; Desulfurization of Fuels and Waste Streams; Control of Air Emissions; MTBE/Phytoremediation and Natural Attenuation; and Treatment and Remediation of Petroleum Hydrocarbons. The last day of the conference was devoted to a special symposium on 'Innovative Technologies for Subsurface Characterization and Remediation.' The authors recommend this conference as a forum for industry, government, and academia to freely exchange ideas and information

Figures on petroleum 1981

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This table taken out from the 1981 annual report 1981 contains an introductory remark on the reorganization of mineral oil statistics up to January 82. It is followed by the tables ranged as follows: refinery capacity and production, crude oil supply, GDR-coverings, import of petroleum products, petroleum consumption, export of petroleum products, transport, oil storage tanks, motor vehicle stock, taxes and tariffs, petroleum export trade, energy consumption and world petroleum numbers. In parts the tables contain comparative figures back to 1950.

Petroleum supply monthly, April 1990

Energy Technology Data Exchange (ETDEWEB)

None

1990-06-26

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the Petroleum Supply Monthly describe (PSM) the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply.'' Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: (1) the Summary Statistics and (2) the Detailed Statistics.

Mechanical design criteria for intervertebral disc tissue engineering.

Science.gov (United States)

Nerurkar, Nandan L; Elliott, Dawn M; Mauck, Robert L

2010-04-19

Due to the inability of current clinical practices to restore function to degenerated intervertebral discs, the arena of disc tissue engineering has received substantial attention in recent years. Despite tremendous growth and progress in this field, translation to clinical implementation has been hindered by a lack of well-defined functional benchmarks. Because successful replacement of the disc is contingent upon replication of some or all of its complex mechanical behaviors, it is critically important that disc mechanics be well characterized in order to establish discrete functional goals for tissue engineering. In this review, the key functional signatures of the intervertebral disc are discussed and used to propose a series of native tissue benchmarks to guide the development of engineered replacement tissues. These benchmarks include measures of mechanical function under tensile, compressive, and shear deformations for the disc and its substructures. In some cases, important functional measures are identified that have yet to be measured in the native tissue. Ultimately, native tissue benchmark values are compared to measurements that have been made on engineered disc tissues, identifying where functional equivalence was achieved, and where there remain opportunities for advancement. Several excellent reviews exist regarding disc composition and structure, as well as recent tissue engineering strategies; therefore this review will remain focused on the functional aspects of disc tissue engineering. Copyright 2009 Elsevier Ltd. All rights reserved.

Petroleum supply monthly, April 1994

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

The Strategic Petroleum Reserve: United States energy security, oil politics, and petroleum reserves policies in the twentieth century

Science.gov (United States)

Beaubouef, Bruce Andre

The history of U.S. petroleum reserves policies in the twentieth century, including the Strategic Petroleum Reserve (SPR) program, provides a case study of the economic and political aspects of national security, and shows the ways in which the American political economy influences national security. One key problem plagued federal petroleum reserve programs and proposals throughout the twentieth century. In a political economy which traditionally placed strong emphasis upon the sanctity of private property and free markets, could the government develop an emergency petroleum reserve policy despite opposition from the private sector? Previous literature on the SPR and oil-stockpiling programs has largely disregarded the historical perspective, focusing instead upon econometric models, suggesting future oil-stockpiling policy options. This study will also make conclusions about the future of governmental oil-stockpiling policies, particularly with regard to the SPR program, but it will do so informed by a systematic history of the emergency petroleum reserve impulse in the twentieth century. Through a study of the emergency petroleum reserve impulse, one can see how the American political economy of oil and energy changed over the twentieth century. As petroleum became crucial to the military and then economic security of the United States, the federal government sought to develop emergency petroleum reserves first for the military, then for the civilian economy. But while the American petroleum industry could deliver the energy "goods" to American energy consumers at a reasonable price, the companies reigned supreme in the political equation. While that was true, federal petroleum reserve programs and proposals conflicted with and were overwhelmed by the historic American tradition of individual economic and private property rights. The depletion of American petroleum reserves changed that political equation, and the ensuing energy crises of the 1970s not only

DESIGN QUALITY IN MECHANICAL ENGINEERING APPLICATION

Directory of Open Access Journals (Sweden)

Ayşegül Akdogan Eker

2010-09-01

Full Text Available There is a close relationship between material chose and quality in mechanical engineering application like there is in all the other engineering applications. If this relation is balanced then engineering success increases. Material chose comes to fore in the design process most of the time. The two most important responsibilities of the design engineer in here is to chose suitable material and to know the production processes about design. The chose of material of a design that will fulfill the needs all through its life has great importance. It is needed to limit the material applicants by choosing the most suitable ones among variable material. Choosing materials that were examined before and whose behavior is well known provides the designer to feel confident. However since using highly successful materials would increase the competitive power of the designs; designers should follow the developments in materials and know the features of new materials. The description of these features can be interpreted within quality. Quality from the point of engineer is the total fulfillment of expectations.Engineer today are faced with very important problems such as fast technological innovations, a dynamic socio-economical environment, global rivalry. One of the life buoys they stick while trying to solve these problems is total method of quality control. Total Quality model which can provide higher competitive power compared to classical management model brings success only when applied with its whole components. "Approach toward prevention" and "measurement and statistics" have an important place among these elements. The first step of the approach toward prevention composes of design quality and Quality Function Deployment (QFD, or in other words The House of Quality method that will provide this. In this paper; considering the quality function deployment, how the chose of material are done in mechanical engineering applications will be explained.

Fire and explosion safety in the petroleum sector

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

The conference has 13 presentations in topics on LNG projects nationally and internationally, simulations of gas dispersion due to LNG discharges, transports of pressurized natural gas, technological aspects of fire protection and combat equipment, safety aspects of offshore installations and transportation systems, offshore platform and transportation systems design and various examples of safety design and management. Some experiences within safety engineering in the petroleum exploitation are included.

Degradation of petroleum hydrocarbons in a laboratory aquifer column

International Nuclear Information System (INIS)

Billowits, M.; Whyte, L.; Greer, C.; Ramsay, J.

1998-01-01

One of the primary mechanisms for eliminating hydrocarbon pollutants from the environment is degradation of hydrocarbons by indigenous microorganisms. This report describes a study in which samples from a petroleum polluted shallow aquifer in the Yukon were used which contained a hundred times greater concentration of psychrotropic bacteria than mesophilic bacteria. Results showed a maximum degradation of 47 per cent of the total petroleum hydrocarbon in columns which simulated the aquifer conditions and to which nutrients were added. It was concluded that although in this case bioaugmentation of the columns with a psychrotropic hydrocarbon-degrading consortium increased microbial numbers, total petroleum hydrocarbon degradation was not much greater than could be achieved by remediation with nutrients alone

Petroleum marketing annual 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-24

The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date.

Petroleum marketing annual 1994

International Nuclear Information System (INIS)

1995-01-01

The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date

Effect of engine parameters and type of gaseous fuel on the performance of dual-fuel gas diesel engines. A critical review

Energy Technology Data Exchange (ETDEWEB)

Sahoo, B.B. [Centre for Energy, Indian Institute of Technology, Guwahati 781039 (India); Sahoo, N.; Saha, U.K. [Department of Mechanical Engineering, Indian Institute of Technology, Guwahati 781039 (India)

2009-08-15

Petroleum resources are finite and, therefore, search for their alternative non-petroleum fuels for internal combustion engines is continuing all over the world. Moreover gases emitted by petroleum fuel driven vehicles have an adverse effect on the environment and human health. There is universal acceptance of the need to reduce such emissions. Towards this, scientists have proposed various solutions for diesel engines, one of which is the use of gaseous fuels as a supplement for liquid diesel fuel. These engines, which use conventional diesel fuel and gaseous fuel, are referred to as 'dual-fuel engines'. Natural gas and bio-derived gas appear more attractive alternative fuels for dual-fuel engines in view of their friendly environmental nature. In the gas-fumigated dual-fuel engine, the primary fuel is mixed outside the cylinder before it is inducted into the cylinder. A pilot quantity of liquid fuel is injected towards the end of the compression stroke to initiate combustion. When considering a gaseous fuel for use in existing diesel engines, a number of issues which include, the effects of engine operating and design parameters, and type of gaseous fuel, on the performance of the dual-fuel engines, are important. This paper reviews the research on above issues carried out by various scientists in different diesel engines. This paper touches upon performance, combustion and emission characteristics of dual-fuel engines which use natural gas, biogas, producer gas, methane, liquefied petroleum gas, propane, etc. as gaseous fuel. It reveals that 'dual-fuel concept' is a promising technique for controlling both NO{sub x} and soot emissions even on existing diesel engine. But, HC, CO emissions and 'bsfc' are higher for part load gas diesel engine operations. Thermal efficiency of dual-fuel engines improve either with increased engine speed, or with advanced injection timings, or with increased amount of pilot fuel. The ignition

Thermal integrity in mechanics and engineering

International Nuclear Information System (INIS)

Shorr, Boris F.

2015-01-01

The book is targeted at engineers, university lecturers, postgraduates, and final year undergraduate students involved in computational modelling and experimental and theoretical analysis of the high-temperature behavior of engineering structures. It will also be of interest to researchers developing the thermal strength theory as a branch of continuum mechanics. Thermal integrity is a multidisciplinary field combining the expertise of mechanical engineers, material scientists and applied mathematicians, each approaching the problem from their specific viewpoint. This monograph draws on the research of a broad scientific community including the author's contribution. The scope of thermal strength analysis was considerably extended thanks to modern computers and the implementation of FEM codes. However, the author believes that some material models adopted in the advanced high-performance software, are not sufficiently justificated due to lack of easy-to-follow books on the theoretical and experimental aspects of thermal integrity. The author endeavors to provide a thorough yet sufficiently simple presentation of the underlying concepts, making the book compelling to a wide audience.

Thermal integrity in mechanics and engineering

Energy Technology Data Exchange (ETDEWEB)

Shorr, Boris F. [Central Institute of Aviation Motors (CIAM), Moscow (Russian Federation)

2015-07-01

The book is targeted at engineers, university lecturers, postgraduates, and final year undergraduate students involved in computational modelling and experimental and theoretical analysis of the high-temperature behavior of engineering structures. It will also be of interest to researchers developing the thermal strength theory as a branch of continuum mechanics. Thermal integrity is a multidisciplinary field combining the expertise of mechanical engineers, material scientists and applied mathematicians, each approaching the problem from their specific viewpoint. This monograph draws on the research of a broad scientific community including the author's contribution. The scope of thermal strength analysis was considerably extended thanks to modern computers and the implementation of FEM codes. However, the author believes that some material models adopted in the advanced high-performance software, are not sufficiently justificated due to lack of easy-to-follow books on the theoretical and experimental aspects of thermal integrity. The author endeavors to provide a thorough yet sufficiently simple presentation of the underlying concepts, making the book compelling to a wide audience.

Elements of Motivational Structure for Studying Mechanical Engineering

OpenAIRE

Nikša Dubreta; Damir Miloš

2017-01-01

The article presents the findings on students' reasons for studying mechanical engineering. These reasons were covered in terms of extrinsic and intrinsic motivation additionally related to selected independent variables of the sample – students' secondary school Grade Point Average, their gender and the socio-economic status. The research was conducted with the first year students of the Faculty of Mechanical Engineering at the University of Zagreb, Croatia. The sample consisted of 282 stude...

Analysis of the Lifecycle of Mechanical Engineering Products

OpenAIRE

Gubaidulina, Rauza Khamidovna; Gruby, S. V.; Davlatov, G. D.

2016-01-01

Principal phases of the lifecycle of mechanical engineering products are analyzed in the paper. The authors have developed methods and procedures to improve designing, manufacturing, operating and recycling of the machine. It has been revealed that economic lifecycle of the product is a base for appropriate organization of mechanical engineering production. This lifecycle is calculated as a minimal sum total of consumer and producer costs. The machine construction and its manufacturing techno...

Petroleum supply monthly, January 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-15

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum supply monthly, October 1993

Energy Technology Data Exchange (ETDEWEB)

1993-10-26

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Petroleum Supply Monthly, August 1990

Energy Technology Data Exchange (ETDEWEB)

1990-10-30

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) district movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics.

Petroleum supply monthly, September 1991

Energy Technology Data Exchange (ETDEWEB)

1991-09-30

The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

SMAP Instrument Mechanical System Engineering

Science.gov (United States)

Slimko, Eric; French, Richard; Riggs, Benjamin

2013-01-01

The Soil Moisture Active Passive (SMAP) mission, scheduled for launch by the end of 2014, is being developed to measure the soil moisture and soil freeze/thaw state on a global scale over a three-year period. The accuracy, resolution, and global coverage of SMAP measurements are invaluable across many science and applications disciplines including hydrology, climate, carbon cycle, and the meteorological, environment, and ecology applications communities. The SMAP observatory is composed of a despun bus and a spinning instrument platform that includes both a deployable 6 meter aperture low structural frequency Astromesh reflector and a spin control system. The instrument section has engendered challenging mechanical system issues associated with the antenna deployment, flexible antenna pointing in the context of a multitude of disturbances, spun section mass properties, spin control system development, and overall integration with the flight system on both mechanical and control system levels. Moreover, the multitude of organizations involved, including two major vendors providing the spin subsystem and reflector boom assembly plus the flight system mechanical and guidance, navigation, and control teams, has led to several unique system engineering challenges. Capturing the key physics associated with the function of the flight system has been challenging due to the many different domains that are applicable. Key interfaces and operational concepts have led to complex negotiations because of the large number of organizations that integrate with the instrument mechanical system. Additionally, the verification and validation concerns associated with the mechanical system have had required far-reaching involvement from both the flight system and other subsystems. The SMAP instrument mechanical systems engineering issues and their solutions are described in this paper.

Petroleum price

International Nuclear Information System (INIS)

Chevallier, B.

2009-01-01

The 'AFTP' conference on 'petroleum prices' organized by Total last March, tries to explain the different aspects of the crisis we undergo for July 2007 and its consequential effects on the petroleum markets (supply, demand evolvements, impacts on reserves, prices, refining...). (O.M.)

77 FR 56421 - Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...

Science.gov (United States)

2012-09-12

... Parts 9 and 60 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...-9672-3] RIN 2060-AN72 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007...

Petroleum supply monthly, January 1994

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum marketing monthly, July 1994

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

Petroleum supply monthly, August 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-26

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

46 CFR 148.04-15 - Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture).

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture). 148.04-15 Section 148.04-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Certain Material § 148.04-15 Petroleum coke, uncalcined; petroleum coke, uncalcined and...

Petroleum and geopolitics

International Nuclear Information System (INIS)

Chaigneau, P.

2004-01-01

Todays, petroleum companies consider that despite the constant increase of petroleum consumption, petroleum will remain the main energy source for at least 40 years. However, after the Iraq conflict, new regional situations are changing. China, for instance, with its growing up demand, will change the physiognomy of the oil market. In parallel, from Indonesia to Africa, petroleum and religion interfere and explain the new conflict areas. As for the US strategy, which is not limited to the energy paradigm, it largely integrates energy in the main lines of its diplomacy, from the 'Wide Middle East' to the 'Sahel initiative', and in its position with respect to Venezuela

Determination of radioactivity in petroleum products and wastes

International Nuclear Information System (INIS)

Hrichi, Hajer

2009-01-01

At this end engineering study, we determined the activities of gamma- emitting radionuclides belonging to the families of 238 U, 235 U, 232 Th and 40K in the petroleum products and wastes of the refinery S.T.I.R. The activities of radionuclides which exceed that of crude oil prove that it's a technologically enhanced natural radioactivity since several chemical products were injected during the refining process. (Author)

Reliability design of mechanical systems a guide for mechanical and civil engineers

CERN Document Server

Woo, Seongwoo

2017-01-01

This book describes basic reliability concepts – parametric ALT plan, failure mechanism and design, and reliability testing with acceleration factor and sample size equation. A generalized life-stress failure model with a new effort concept has been derived and recommended to calculate the acceleration factor of the mechanical system. The new sample size equation with the acceleration factor has also been derived to carry out the parametric ALT. This new parametric ALT should help a mechanical/civil engineer to uncover the design parameters affecting reliability during the design process of the mechanical system. Consequently, it should help companies to improve product reliability and avoid recalls due to the product/structure failures in the field. As the improper or missing design parameters in the design phase are experimentally identified by this new reliability design method - parametric ALT, the mechanical/civil engineering system might improve in reliability by the increase in lifetime and the reduc...

Mechanical Engineering Department engineering research: Annual report, FY 1986

International Nuclear Information System (INIS)

Denney, R.M.; Essary, K.L.; Genin, M.S.; Highstone, H.H.; Hymer, J.D.; Taft, S.O.

1986-12-01

This report provides information on the five areas of research interest in LLNL's Mechanical Engineering Department. In Computer Code Development, a solid geometric modeling program is described. In Dynamic Systems and Control, structure control and structure dynamics are discussed. Fabrication technology involves machine cutting, interferometry, and automated optical component manufacturing. Materials engineering reports on composite material research and measurement of molten metal surface properties. In Nondestructive Evaluation, NMR, CAT, and ultrasound machines are applied to manufacturing processes. A model for underground collapse is developed. Finally, an alternative heat exchanger is investigated for use in a fusion power plant. Separate abstracts were prepared for each of the 13 reports in this publication

Petroleum Supply Monthly, July 1990

Energy Technology Data Exchange (ETDEWEB)

1990-09-28

Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

2012 International Conference on Mechanical and Electronic Engineering

CERN Document Server

Lin, Sally; ICMEE2012; Advances in Mechanical and Electronic Engineering v.2

2012-01-01

This book includes the volume 2 of the proceedings of the 2012 International Conference on Mechanical and Electronic Engineering(ICMEE2012), held at June 23-24,2012 in Hefei, China. The conference provided a rare opportunity to bring together worldwide researchers who are working in the fields. This volume 2 is focusing on Mechatronic Engineering and Technology,  Electronic Engineering and Electronic Information Technology .

Engineering three-dimensional cell mechanical microenvironment with hydrogels.

Science.gov (United States)

Huang, Guoyou; Wang, Lin; Wang, Shuqi; Han, Yulong; Wu, Jinhui; Zhang, Qiancheng; Xu, Feng; Lu, Tian Jian

2012-12-01

Cell mechanical microenvironment (CMM) significantly affects cell behaviors such as spreading, migration, proliferation and differentiation. However, most studies on cell response to mechanical stimulation are based on two-dimensional (2D) planar substrates, which cannot mimic native three-dimensional (3D) CMM. Accumulating evidence has shown that there is a significant difference in cell behavior in 2D and 3D microenvironments. Among the materials used for engineering 3D CMM, hydrogels have gained increasing attention due to their tunable properties (e.g. chemical and mechanical properties). In this paper, we provide an overview of recent advances in engineering hydrogel-based 3D CMM. Effects of mechanical cues (e.g. hydrogel stiffness and externally induced stress/strain in hydrogels) on cell behaviors are described. A variety of approaches to load mechanical stimuli in 3D hydrogel-based constructs are also discussed.

Engineering three-dimensional cell mechanical microenvironment with hydrogels

International Nuclear Information System (INIS)

Huang Guoyou; Wang Lin; Han Yulong; Zhang Qiancheng; Xu Feng; Lu Tianjian; Wang Shuqi; Wu Jinhui

2012-01-01

Cell mechanical microenvironment (CMM) significantly affects cell behaviors such as spreading, migration, proliferation and differentiation. However, most studies on cell response to mechanical stimulation are based on two-dimensional (2D) planar substrates, which cannot mimic native three-dimensional (3D) CMM. Accumulating evidence has shown that there is a significant difference in cell behavior in 2D and 3D microenvironments. Among the materials used for engineering 3D CMM, hydrogels have gained increasing attention due to their tunable properties (e.g. chemical and mechanical properties). In this paper, we provide an overview of recent advances in engineering hydrogel-based 3D CMM. Effects of mechanical cues (e.g. hydrogel stiffness and externally induced stress/strain in hydrogels) on cell behaviors are described. A variety of approaches to load mechanical stimuli in 3D hydrogel-based constructs are also discussed. (topical review)

Well-Posedness of a fully coupled thermo-chemo-poroelastic system with applications to petroleum rock mechanics

Directory of Open Access Journals (Sweden)

Tetyana Malysheva

2017-05-01

Full Text Available We consider a system of fully coupled parabolic and elliptic equations constituting the general model of chemical thermo-poroelasticity for a fluid-saturated porous media. The main result of this paper is the developed well-posedness theory for the corresponding initial-boundary problem arising from petroleum rock mechanics applications. Using the proposed pseudo-decoupling method, we establish, subject to some natural assumptions imposed on matrices of diffusion coefficients, the existence, uniqueness, and continuous dependence on initial and boundary data of a weak solution to the problem. Numerical experiments confirm the applicability of the obtained well-posedness results for thermo-chemo-poroelastic models with real-data parameters.

Microfabrication of hierarchical structures for engineered mechanical materials

Science.gov (United States)

Vera Canudas, Marc

Materials found in nature present, in some cases, unique properties from their constituents that are of great interest in engineered materials for applications ranging from structural materials for the construction of bridges, canals and buildings to the fabrication of new lightweight composites for airplane and automotive bodies, to protective thin film coatings, amongst other fields. Research in the growing field of biomimetic materials indicates that the micro-architectures present in natural materials are critical to their macroscopic mechanical properties. A better understanding of the effect that structure and hierarchy across scales have on the material properties will enable engineered materials with enhanced properties. At the moment, very few theoretical models predict mechanical properties of simple materials based on their microstructures. Moreover these models are based on observations from complex biological systems. One way to overcome this challenge is through the use of microfabrication techniques to design and fabricate simple materials, more appropriate for the study of hierarchical organizations and microstructured materials. Arrays of structures with controlled geometry and dimension can be designed and fabricated at different length scales, ranging from a few hundred nanometers to centimeters, in order to mimic similar systems found in nature. In this thesis, materials have been fabricated in order to gain fundamental insight into the complex hierarchical materials found in nature and to engineer novel materials with enhanced mechanical properties. The materials fabricated here were mechanically characterized and compared to simple mechanics models to describe their behavior with the goal of applying the knowledge acquired to the design and synthesis of future engineered materials with novel properties.

Petroleum marketing monthly, June 1994

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. The feature article is entitled ``The Second Oxygenated Gasoline Season.`` 7 figs., 50 tabs.

The development and application of CFD technology in mechanical engineering

Science.gov (United States)

Wei, Yufeng

2017-12-01

Computational Fluid Dynamics (CFD) is an analysis of the physical phenomena involved in fluid flow and heat conduction by computer numerical calculation and graphical display. The numerical method simulates the complexity of the physical problem and the precision of the numerical solution, which is directly related to the hardware speed of the computer and the hardware such as memory. With the continuous improvement of computer performance and CFD technology, it has been widely applied to the field of water conservancy engineering, environmental engineering and industrial engineering. This paper summarizes the development process of CFD, the theoretical basis, the governing equations of fluid mechanics, and introduces the various methods of numerical calculation and the related development of CFD technology. Finally, CFD technology in the mechanical engineering related applications are summarized. It is hoped that this review will help researchers in the field of mechanical engineering.

Deconstructing Engineering Education Programmes: The DEEP Project to Reform the Mechanical Engineering Curriculum

Science.gov (United States)

Busch-Vishniac, Ilene; Kibler, Tom; Campbell, Patricia B.; Patterson, Eann; Guillaume, Darrell; Jarosz, Jeffrey; Chassapis, Constantin; Emery, Ashley; Ellis, Glenn; Whitworth, Horace; Metz, Susan; Brainard, Suzanne; Ray, Pradosh

2011-01-01

The goal of the Deconstructing Engineering Education Programmes project is to revise the mechanical engineering undergraduate curriculum to make the discipline more able to attract and retain a diverse community of students. The project seeks to reduce and reorder the prerequisite structure linking courses to offer greater flexibility for…

Thermodynamic and Mechanical Analysis of a Thermomagnetic Rotary Engine

International Nuclear Information System (INIS)

Fajar, D M; Khotimah, S N; Khairurrijal

2016-01-01

A heat engine in magnetic system had three thermodynamic coordinates: magnetic intensity ℋ, total magnetization ℳ, and temperature T, where the first two of them are respectively analogous to that of gaseous system: pressure P and volume V. Consequently, Carnot cycle that constitutes the principle of a heat engine in gaseous system is also valid on that in magnetic system. A thermomagnetic rotary engine is one model of it that was designed in the form of a ferromagnetic wheel that can rotates because of magnetization change at Curie temperature. The study is aimed to describe the thermodynamic and mechanical analysis of a thermomagnetic rotary engine and calculate the efficiencies. In thermodynamic view, the ideal processes are isothermal demagnetization, adiabatic demagnetization, isothermal magnetization, and adiabatic magnetization. The values of thermodynamic efficiency depend on temperature difference between hot and cold reservoir. In mechanical view, a rotational work is determined through calculation of moment of inertia and average angular speed. The value of mechanical efficiency is calculated from ratio between rotational work and heat received by system. The study also obtains exergetic efficiency that states the performance quality of the engine. (paper)

Thermodynamic and Mechanical Analysis of a Thermomagnetic Rotary Engine

Science.gov (United States)

Fajar, D. M.; Khotimah, S. N.; Khairurrijal

2016-08-01

A heat engine in magnetic system had three thermodynamic coordinates: magnetic intensity ℋ, total magnetization ℳ, and temperature T, where the first two of them are respectively analogous to that of gaseous system: pressure P and volume V. Consequently, Carnot cycle that constitutes the principle of a heat engine in gaseous system is also valid on that in magnetic system. A thermomagnetic rotary engine is one model of it that was designed in the form of a ferromagnetic wheel that can rotates because of magnetization change at Curie temperature. The study is aimed to describe the thermodynamic and mechanical analysis of a thermomagnetic rotary engine and calculate the efficiencies. In thermodynamic view, the ideal processes are isothermal demagnetization, adiabatic demagnetization, isothermal magnetization, and adiabatic magnetization. The values of thermodynamic efficiency depend on temperature difference between hot and cold reservoir. In mechanical view, a rotational work is determined through calculation of moment of inertia and average angular speed. The value of mechanical efficiency is calculated from ratio between rotational work and heat received by system. The study also obtains exergetic efficiency that states the performance quality of the engine.

Speciation of Mercury in Selected Areas of the Petroleum Value Chain.

Science.gov (United States)

Avellan, Astrid; Stegemeier, John P; Gai, Ke; Dale, James; Hsu-Kim, Heileen; Levard, Clément; O'Rear, Dennis; Hoelen, Thomas P; Lowry, Gregory V

2018-02-06

Petroleum, natural gas, and natural gas condensate can contain low levels of mercury (Hg). The speciation of Hg can affect its behavior during processing, transport, and storage so efficient and safe management of Hg requires an understanding of its chemical form in oil, gas and byproducts. Here, X-ray absorption spectroscopy was used to determine the Hg speciation in samples of solid residues collected throughout the petroleum value chain including stabilized crude oil residues, sediments from separation tanks and condensate glycol dehydrators, distillation column pipe scale, and biosludge from wastewater treatment. In all samples except glycol dehydrators, metacinnabar (β-HgS) was the primary form of Hg. Electron microscopy on particles from a crude sediment showed nanosized (crude oil being processed, i.e. sweet (low sulfur crudes) vs sour (higher sulfur crudes). This information on Hg speciation in the petroleum value chain will inform development of better engineering controls and management practices for Hg.

Mechanical Engineering Department engineering research: Annual report, FY 1986

Energy Technology Data Exchange (ETDEWEB)

Denney, R.M.; Essary, K.L.; Genin, M.S.; Highstone, H.H.; Hymer, J.D.; Taft, S.O. (eds.)

1986-12-01

This report provides information on the five areas of research interest in LLNL's Mechanical Engineering Department. In Computer Code Development, a solid geometric modeling program is described. In Dynamic Systems and Control, structure control and structure dynamics are discussed. Fabrication technology involves machine cutting, interferometry, and automated optical component manufacturing. Materials engineering reports on composite material research and measurement of molten metal surface properties. In Nondestructive Evaluation, NMR, CAT, and ultrasound machines are applied to manufacturing processes. A model for underground collapse is developed. Finally, an alternative heat exchanger is investigated for use in a fusion power plant. Separate abstracts were prepared for each of the 13 reports in this publication. (JDH)

Petroleum and Health Care: Evaluating and Managing Health Care's Vulnerability to Petroleum Supply Shifts

Science.gov (United States)

Bednarz, Daniel; Bae, Jaeyong; Pierce, Jessica

2011-01-01

Petroleum is used widely in health care—primarily as a transport fuel and feedstock for pharmaceuticals, plastics, and medical supplies—and few substitutes for it are available. This dependence theoretically makes health care vulnerable to petroleum supply shifts, but this vulnerability has not been empirically assessed. We quantify key aspects of petroleum use in health care and explore historical associations between petroleum supply shocks and health care prices. These analyses confirm that petroleum products are intrinsic to modern health care and that petroleum supply shifts can affect health care prices. In anticipation of future supply contractions lasting longer than previous shifts and potentially disrupting health care delivery, we propose an adaptive management approach and outline its application to the example of emergency medical services. PMID:21778473

Petroleum and ethics

International Nuclear Information System (INIS)

Henn, N.; Train, E.; Chagnoux, H.; Heinzle, P.; Daubresse, M.; Bret-Rouzaut, N.; Fradin, J.

2000-01-01

7 articles in this data sheet, they concern: political stakes and stakes of the industrial petroleum sector towards ethical questions; establishment of associations attending to human and environmental questions; examples of of ethical, environmental and safety policy in an industrialized country (ExxonMobil) and in a developing country (TotalFina); synthesis of the ethical problems that the petroleum industry encounter in industrialized and developing countries; considerations on the communication stakes in petroleum companies with the general public. (O.M.)

Petroleum marketing monthly, May 1994

Energy Technology Data Exchange (ETDEWEB)

1994-05-26

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Development of Engineering Design Education in the Department of Mechanical Engineering at Kanazawa Technical College

Science.gov (United States)

Yamada, Hirofumi; Ten-Nichi, Michio; Mathui, Hirosi; Nakamura, Akizi

This paper introduces a method of the engineering design education for college of technology mechanical engineering students. In order to teach the practical engineering design, the MIL-STD-499A process is adapted and improved upon for a Mechatronics hands-on lesson used as the MOT method. The educational results in five years indicate that knowledge of the engineering management is useful for college students in learning engineering design. Portfolio for lessons and the hypothesis method also have better effects on the understanding of the engineering specialty.

Petroleum question. Die Oelfrage

Energy Technology Data Exchange (ETDEWEB)

Mommer, B

1983-01-01

The author analyses the development of the world petroleum market and its pricing factors to the present on the basis of the theory of ground rent, in which the part played by absolute ground rent, differential rent, and free and national state property in the capitalist mode of production is determined. His investigation of economic policy traces the absorbing history of the petroleum production and policy of the United States of America, which for so long governed the world market, the development of Venezuela into a petroleum country (whose true history is here revealed for the first time), the penetration of the middle East by the international petroleum leaseholders' capital and their cartel, the formation of the OPEC, and finally the 'victory' of the lather over the petroleum combines in the international petroleum crisis of 1970-1973. The book closes with a survey at the start of the 80s and an outlook into the foreseeable future. What is really hidden behind the quarrels about prices, profit, taxes, royalties, franchise agreements, production quotas, nationalization and so forth and behind the economic, political, and even moral arguments of the parties concerned turns out to be the fight of the petroleum ground proprietors for the ground rent - but to win a victory in this fight means ultimately to face its limitations, too. Blindness to the economic and political importance of ground rent, right from the theoretical approach, also created a major cause of the false diagnoses and forecasts on the petroleum market western economic scientists were misled into, and thus of the surprise effect that came in the form of the petroleum crisis of the early 1970s.

Indicators on the world petroleum markets

International Nuclear Information System (INIS)

2000-10-01

This paper presents tendencies of the petroleum industry market. It analyses the petroleum demand and supply, the prices elaboration, the petroleum market and the OPEC objective, the third petroleum crisis of the year 2000 and gives some data concerning the petroleum market. (A.L.B.)

Figures of the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

The statistic tables give informations about: Reserves and production of petroleum and natural gas, supply of crude petroleum in the Federal Republic of Germany, pipelines, tanker ships, petroleum refineries, petroleum consumption, storage and distribution, automobiles, prices, taxis and energy consumption. The data compilations are primarily given for the Federal Republic of Germany.

Petroleum Oxidation in Marine Microcosms by Natural Microbial Assemblages

Science.gov (United States)

Wardlaw, G. D.; Reddy, C. M.; Nelson, R. K.; Ehrhardt, C. J.; Valentine, D. L.

2006-12-01

Millions of gallons of petroleum are emitted into marine environments each year and the oxidation of this oil by microbes is an important mechanism for mediating toxicity. In terms of quantity, petroleum is the most abundant organic pollutant impacting marine environments today. Recent advances in chromatography have led to the development of comprehensive two-dimensional gas chromatography (GC &GC). The acronym, GC GC, is used because orthogonal gas chromatographic separations are achieved in both analytical dimensions by using stationary phases with varying partitioning abilities and selectivity. This novel method has greatly expanded the analytical window of petroleum hydrocarbons and was used to track the loss of petroleum hydrocarbons in aerobic marine microcosm experiments. Sediment microcosms were composed of seawater and sediment collected from the Coal Oil Point (COP) seep field off the coast of Santa Barbara, CA. Oil collected directly from the reservoir underlying the seep field was added to each microcosm, and samples were incubated for one year. Net metabolism was tracked by quantifying oxygen consumption and carbon dioxide production. The loss of petroleum components was tracked with GC GC, whereas the bacterial and archaeal community structures were tracked using T-RFLP. Results of these incubation studies will be presented.

Chemistry of fossil fuels and biofuels (cambridge series in chemical engineering)

CERN Document Server

Schobert, Harold

2013-01-01

Focusing on today's major fuel resources - ethanol, biodiesel, wood, natural gas, petroleum products and coal - this book discusses the formation, composition and properties of the fuels, and the ways in which they are processed for commercial use. The book examines the origin of fuels through natural processes such as photosynthesis and the geological transformation of ancient plant material; the relationships between their composition, molecular structures, and physical properties; and the various processes by which they are converted or refined into the fuel products appearing on today's market. Fundamental chemical aspects such as catalysis and the behaviour of reactive intermediates are presented, and global warming and anthropogenic carbon dioxide emissions are also discussed. The book is suitable for graduate students in energy engineering, chemical engineering, mechanical engineering and chemistry, as well as professional scientists and engineers.

Control Engineering as a Part of Undergraduate Curriculum for Mechanical Engineering in India

Science.gov (United States)

Akhtar, Shagil; Iqbal, Syed Muneeb; Bajpai, Shrish

2016-01-01

In this present study we have traced the genesis of control engineering in the scope of mechanical engineering and then some analysis on its recent developments, their increasing need and how this particular subject has evolved machines functioning nowadays specifically its standard of education in India. We have probed this field right from its…

Petroleum marketing monthly, August 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-15

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product Sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly, September 1994

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum product sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Deformation and fracture mechanics of engineering materials

National Research Council Canada - National Science Library

Hertzberg, Richard W; Vinci, Richard Paul; Hertzberg, Jason L

2012-01-01

"Hertzberg's 5th edition of Deformation & Fracture Mechanics of Engineering Materials offers several new features including a greater number and variety of homework problems using more computational software...

Mechanics of oriented electrospun nanofibrous scaffolds for annulus fibrosus tissue engineering.

Science.gov (United States)

Nerurkar, Nandan L; Elliott, Dawn M; Mauck, Robert L

2007-08-01

Engineering a functional replacement for the annulus fibrosus (AF) of the intervertebral disc is contingent upon recapitulation of AF structure, composition, and mechanical properties. In this study, we propose a new paradigm for AF tissue engineering that focuses on the reconstitution of anatomic fiber architecture and uses constitutive modeling to evaluate construct function. A modified electrospinning technique was utilized to generate aligned nanofibrous polymer scaffolds for engineering the basic functional unit of the AF, a single lamella. Scaffolds were tested in uniaxial tension at multiple fiber orientations, demonstrating a nonlinear dependence of modulus on fiber angle that mimicked the nonlinearity and anisotropy of native AF. A homogenization model previously applied to native AF successfully described scaffold mechanical response, and parametric studies demonstrated that nonfibrillar matrix, along with fiber connectivity, are key contributors to tensile mechanics for engineered AF. We demonstrated that AF cells orient themselves along the aligned scaffolds and deposit matrix that contributes to construct mechanics under loading conditions relevant to the in vivo environment. The homogenization model was applied to cell-seeded constructs and provided quantitative measures for the evolution of matrix and interfibrillar interactions. Finally, the model demonstrated that at fiber angles of the AF (28 degrees -44 degrees ), engineered material behaved much like native tissue, suggesting that engineered constructs replicate the physiologic behavior of the single AF lamella. Constitutive modeling provides a powerful tool for analysis of engineered AF neo-tissue and native AF tissue alike, highlighting key mechanical design criteria for functional AF tissue engineering.

Yugoslavian Petroleum Refinery development program

International Nuclear Information System (INIS)

Ocic, Ozren

1999-01-01

This paper shows the analysis of the world petroleum industry development, being an important factor in planning the development of the Yugoslav petroleum industry and Pancevo Petroleum Refinery, as well. Then Yugoslav petroleum industry development is analysed, including the appropriate balances of crude oil production and crude oil products consumption. The way of realizing the basic targets are also proposed. Likewise, the analysis of the condition within West European refineries has been conducted, from the aspects of technology, energy consumption and environmental protection and the same analysis for Pancevo Petroleum Refinery has been presented, too. The analysis of the condition within the refineries in the European Union countries and comparing it with the condition within Pancevo Petroleum Refinery, makes it mainly possible to recognize the development programmes which should be realized in order that Pancevo Petroleum Refinery could reach the refining level of the EU countries. (Original)

Facts 2010 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Mechanical and materials engineering of modern structure and component design

CERN Document Server

Altenbach, Holm

2015-01-01

This book presents the latest findings on mechanical and materials engineering as applied to the design of modern engineering materials and components. The contributions cover the classical fields of mechanical, civil and materials engineering, as well as bioengineering and advanced materials processing and optimization. The materials and structures discussed can be categorized into modern steels, aluminium and titanium alloys, polymers/composite materials, biological and natural materials, material hybrids and modern nano-based materials. Analytical modelling, numerical simulation, state-of-the-art design tools and advanced experimental techniques are applied to characterize the materials’ performance and to design and optimize structures in different fields of engineering applications.

Production by thermo-mechanical process and stability in crude petroleum studies of Ba{sub 2}AlZrO{sub 5,5} ceramics; Producao por processo termo-mecanico e estudos de estabilidade em petroleo cru da ceramica Ba{sub 2}AlZrO{sub 5,5}

Energy Technology Data Exchange (ETDEWEB)

Yadava, Y.P.; Bezerra, L.P.; Ferreira, R.A.S., E-mail: yadava@ufpe.b [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Engenharia Mecanica

2010-07-01

The necessity of developing technologies that makes possible the petroleum wells exploration is very important. Knowing that those are hostile environments is necessary ta find materials that are able to resist to those environment conditions. In this way we worked on the fabrication of ceramic embedding temperature sensors for petroleum industry. The present work looks for the fabrication of Ba{sub 2}AlZrO{sub 5,5} ceramic by thermo-mechanical process and the study of it's stability in crude petroleum. The Ba{sub 2}AlZrO{sub 5,5} was fabricated by thermo-mechanical process. The ceramic powder was calcined and then the granulometry was analyzed by laser. The samples were compacted, sintered and the microstructure and mechanical properties were characterized. The ceramic stability study in crude petroleum was done and the ceramic was analyzed by X-Ray diffraction and Vickers micro hardness The results shows that the ceramic is stable in crude petroleum. (author)

Creating mechanisms of toxic substances emission of combustion engines

OpenAIRE

Jankowski Antoni; Kowalski Mirosław

2015-01-01

The paper analyses the mechanisms of creation of toxic exhaust gases, which mainly derived from inexact fuel metering and improper air-fuel mixture preparation. The paper describes the process of creating toxic components in the exhaust gases of piston engines during engine operation, and impact on the emission of these components determining the composition of the fuel mixture determined equivalence factor Φ. The principal mechanisms of formation of toxic exhaust gases, in particular nitroge...

Petroleum refining and air quality

International Nuclear Information System (INIS)

Raimbault, C.

1992-01-01

This paper studies the methods which may be developed in petroleum refineries or during petroleum products using for air pollution abatement: petroleum products desulfurization, lead elimination in gasoline and catalytic converters to reduce sulfur dioxide and nitrogen oxides in exhaust gases. Investments and costs estimation to adapt petroleum refineries for environment protection is also given. 1 ref., 6 figs., 6 tabs

Facts 2011 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2011-07-15

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Facts 2010 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2010-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

Changing demographics and shrinking engineering enrollments

International Nuclear Information System (INIS)

Vetter, B.M.

1992-01-01

This paper reports that changing U.S. population demographics, poor academic preparation, and a decreasing interest in engineering among college student indicate possible shortages ahead, particularly among chemical and petroleum engineers. If we are to ensure an adequate future supply for the U.S., the engineering talent pool must be enlarged to include women and minority men

Dynamic model of Stirling engine crank mechanism with connected electric generator

Directory of Open Access Journals (Sweden)

Vlach R.

2009-06-01

Full Text Available This paper treats of a numerical dynamic model of Stirling engine crank mechanism. The model is included in the complex model of combined heat and power unit. The unit is composed of the Stirling engine and of attached three-phase synchronous generator. This generator should start the Stirling engine in motor mode as well. It is necessary to combine the crank shaft dynamic model and the complete thermal model of Stirling engine for simulations and analyses of engine run. Our aim is to create a dynamics model which takes into account the parameters of crankshaft, piston rods, pistons, and attached generator. For unit working, the electro-mechanical behaviour of generator is also important. That is why we experimentally verified the parameters of generator. The measured characteristics are used in a complex model of heat and power unit. Moreover, it is also possible to determine the Stirling engine torque by the help of these electro-mechanical characteristics. These values can be used e. g. for determination of optimal engine working point or for unit control.

Logistics aspects of petroleum pipeline operations

Directory of Open Access Journals (Sweden)

W. J. Pienaar

2010-11-01

Full Text Available The paper identifies, assesses and describes the logistics aspects of the commercial operation of petroleum pipelines. The nature of petroleum-product supply chains, in which pipelines play a role, is outlined and the types of petroleum pipeline systems are described. An outline is presented of the nature of the logistics activities of petroleum pipeline operations. The reasons for the cost efficiency of petroleum pipeline operations are given. The relative modal service effectiveness of petroleum pipeline transport, based on the most pertinent service performance measures, is offered. The segments in the petroleum-products supply chain where pipelines can play an efficient and effective role are identified.

Petroleum supply monthly, March 1994

Energy Technology Data Exchange (ETDEWEB)

1994-03-30

Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

Development of a robust and compact kerosene–diesel reaction mechanism for diesel engines

International Nuclear Information System (INIS)

Tay, Kun Lin; Yang, Wenming; Mohan, Balaji; An, Hui; Zhou, Dezhi; Yu, Wenbin

2016-01-01

Highlights: • An approach is used to develop a robust kerosene–diesel reaction mechanism. • Ignition delay of the kerosene sub-mechanism is well validated with experiments. • The kerosene sub-mechanism reproduces the flame lift-off lengths of Jet-A reasonably well. • The kerosene sub-mechanism performs reasonably well under engine conditions. - Abstract: The use of kerosene fuels in internal combustion engines is getting more widespread. The North Atlantic Treaty Organization military is pushing for the use of a single fuel on the battlefield in order to reduce logistical issues. Moreover, in some countries, fuel adulteration is a serious matter where kerosene is blended with diesel and used in diesel engines. So far, most investigations done regarding the use of kerosene fuels in diesel engines are experimental and there is negligible simulation work done in this area possibly because of the lack of a robust and compact kerosene reaction mechanism. This work focuses on the development of a small but reliable kerosene–diesel reaction mechanism, suitable to be used for diesel engine simulations. The new kerosene–diesel reaction mechanism consists only of 48 species and 152 reactions. Furthermore, the kerosene sub-mechanism in this new mechanism is well validated for its ignition delay times and has proven to replicate kerosene combustion well in a constant volume combustion chamber and an optical engine. Overall, this new kerosene–diesel reaction mechanism is proven to be robust and practical for diesel engine simulations.

Mechanical Engineering Department technical abstracts

International Nuclear Information System (INIS)

Denney, R.M.

1982-01-01

The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts

Identification of petroleum pollution sources

International Nuclear Information System (INIS)

Begak, O.Yu.; Syroezhko, A.M.

2001-01-01

A possibility of preliminary identification of petroleum pollution sources was investigated on specimens of the Khanty-Mansi autonomous district six deposits and specimens of soil and water polluted by these petroleums. Investigations were conducted using IR Fourier spectroscopy and gamma spectrometry, as well as methods of chromato-mass spectrometry and capillary gas liquid chromatography. Every of studied samples of petroleum from different deposits have an individual radiation impression. Insignificant total content of radionuclides in samples is specific to the Khanty-Mansi petroleum region. Gamma spectrometry admits to identify potential source of petroleum pollution using radionuclides of uranium and thorium series [ru

Creating mechanisms of toxic substances emission of combustion engines

Directory of Open Access Journals (Sweden)

Jankowski Antoni

2015-12-01

Full Text Available The paper analyses the mechanisms of creation of toxic exhaust gases, which mainly derived from inexact fuel metering and improper air-fuel mixture preparation. The paper describes the process of creating toxic components in the exhaust gases of piston engines during engine operation, and impact on the emission of these components determining the composition of the fuel mixture determined equivalence factor Φ. The principal mechanisms of formation of toxic exhaust gases, in particular nitrogen oxides, carbon monoxide and hydrocarbons, and also essential according to create each of toxic exhaust gases are the subject of the paper. Moreover, empirical relationships, by means of which it is possible to determine the time of creation of the individual components of toxic exhaust gases, are presented. For example, one of the mechanisms for prompt formation of nitrogen oxides and hydrocarbons graphic illustration of formation as a function of crank angle is described. At the conclusion, the summary and significance of information on creation mechanisms of toxic components in the exhaust gases of piston engines are presented.

Metabolic engineering of microorganisms for biofuels production: from bugs to synthetic biology to fuels

Energy Technology Data Exchange (ETDEWEB)

Kuk Lee, Sung; Chou, Howard; Ham, Timothy S.; Soon Lee, Taek; Keasling, Jay D.

2009-12-02

The ability to generate microorganisms that can produce biofuels similar to petroleum-based transportation fuels would allow the use of existing engines and infrastructure and would save an enormous amount of capital required for replacing the current infrastructure to accommodate biofuels that have properties significantly different from petroleum-based fuels. Several groups have demonstrated the feasibility of manipulating microbes to produce molecules similar to petroleum-derived products, albeit at relatively low productivity (e.g. maximum butanol production is around 20 g/L). For cost-effective production of biofuels, the fuel-producing hosts and pathways must be engineered and optimized. Advances in metabolic engineering and synthetic biology will provide new tools for metabolic engineers to better understand how to rewire the cell in order to create the desired phenotypes for the production of economically viable biofuels.

Microbial dynamics in petroleum oilfields and their relationship with physiological properties of petroleum oil reservoirs.

Science.gov (United States)

Varjani, Sunita J; Gnansounou, Edgard

2017-12-01

Petroleum is produced by thermal decay of buried organic material over millions of years. Petroleum oilfield ecosystems represent resource of reduced carbon which favours microbial growth. Therefore, it is obvious that many microorganisms have adapted to harsh environmental conditions of these ecosystems specifically temperature, oxygen availability and pressure. Knowledge of microorganisms present in ecosystems of petroleum oil reservoirs; their physiological and biological properties help in successful exploration of petroleum. Understanding microbiology of petroleum oilfield(s) can be used to enhance oil recovery, as microorganisms in oil reservoirs produce various metabolites viz. gases, acids, solvents, biopolymers and biosurfactants. The aim of this review is to discuss characteristics of petroleum oil reservoirs. This review also provides an updated literature on microbial ecology of these extreme ecosystems including microbial origin as well as various types of microorganisms such as methanogens; iron, nitrate and sulphate reducing bacteria, and fermentative microbes present in petroleum oilfield ecosystems. Copyright © 2017 Elsevier Ltd. All rights reserved.

The world petroleum industry

International Nuclear Information System (INIS)

Mons, L.

2005-01-01

This study proposes a global vision of the petroleum industry, a precise and well argued state of the art of the petroleum markets. It defines the strategical challenges which the petroleum companies are exposed and allows to anticipate the sector evolutions. It details the key acts of the last three years, the financial performances of the companies. (A.L.B.)

Contact mechanics of reverse engineered distal humeral hemiarthroplasty implants.

Science.gov (United States)

Willing, Ryan; King, Graham J W; Johnson, James A

2015-11-26

Erosion of articular cartilage is a concern following distal humeral hemiarthroplasty, because native cartilage surfaces are placed in contact with stiff metallic implant components, which causes decreases in contact area and increases in contact stresses. Recently, reverse engineered implants have been proposed which are intended to promote more natural contact mechanics by reproducing the native bone or cartilage shape. In this study, finite element modeling is used in order to calculate changes in cartilage contact areas and stresses following distal humeral hemiarthroplasty with commercially available and reverse engineered implant designs. At the ulna, decreases in contact area were -34±3% (p=0.002), -27±1% (pengineered and cartilage reverse engineered designs, respectively. Peak contact stresses increased by 461±57% (p=0.008), 387±127% (p=0.229) and 165±16% (p=0.003). At the radius, decreases in contact area were -21±3% (p=0.013), -13±2% (p0.999), 241±32% (p=0.010) and 61±10% (p=0.021). Between the three different implant designs, the cartilage reverse engineered design yielded the largest contact areas and lowest contact stresses, but was still unable to reproduce the contact mechanics of the native joint. These findings align with a growing body of evidence indicating that although reverse engineered hemiarthroplasty implants can provide small improvements in contact mechanics when compared with commercially available designs, further optimization of shape and material properties is required in order reproduce native joint contact mechanics. Copyright © 2015 Elsevier Ltd. All rights reserved.

Geological evolution of clay sediments: the petroleum exploration vision

International Nuclear Information System (INIS)

Schneider, F.

2004-01-01

The radioactive waste isolation capacity assessment for a clay sediment host rock is link: (1) to the understanding of their present state properties and 3-D repartition (from basin evolution, including sedimentary and diagenetic process); and (2) to the prediction of their future evolution during the next million years. For petroleum exploration, basin modelling aims at reconstructing the accumulation of hydrocarbons at basin scale, and at geological timescale, taking into account the effects of kinematics displacements, sedimentation, erosion, compaction, temperatures history, overpressures and fluids flows (water and hydrocarbons). Furthermore, explorationists wish to address overpressure reconstruction in order to estimate the risks of drilling. Clay sediments are of interest for petroleum exploration because source rocks and seal are generally composed of them. Nevertheless, in spite of their occurrence in nature their evolution at geological timescale is not well understood. And, most of the knowledge has been achieved by those working in the realms of soils mechanics and civil engineering until the present geological investigations for long term radioactive waste repositories. Application of this knowledge to clay sediment is considered to be valid within the first hundreds of meters at the top of the sedimentary pile, according to a repository depth. This paper is dedicated to the sedimentary rocks behaviour at geological timescale. This behaviour is characterised by: (1) the deposition of the sediment; (2) the loading path at geological timescale; (3) the constitutive law which includes the consolidation process and the rupture criteria; and (4) the parameters evolution related to consolidation. (author)

Industrial rag cleaning process for the environmentally safe removal of petroleum-based solvents

International Nuclear Information System (INIS)

Fierro, J.V.

1993-01-01

A process for the cleaning of industrial rags contaminated with environmentally unsafe petroleum-based solvent is described, comprising the step of: (a) placing a load of the industrial rags in a mechanically driven rotary drum; (b) revolving the drum at a high speed sufficient to physically extract liquid petroleum-based solvent contaminate from the industrial rags; (c) routing the extracted petroleum-based solvent contaminate from the rotary drum to a waste solvent collection line for environmentally safe disposal; (d) revolving the rotary drum to cause a tumbling of the industrial rags while maintaining the temperature within the drum at below the flash point of the petroleum-based solvent; (e) intermittently forcing cold air and hot air through the rotary drum to vaporize solvent from the industrial rags; (f) routing the vaporized petroleum-based solvent contaminant from the rotary drum to a condenser wherein the petroleum-based solvent contaminate is condensed and thereafter further routing said condensed solvent to a waste collection line for environmentally safe disposal; and (g) cleaning the industrial rags in the presence of a dry cleaning solvent to remove residual petroleum-based solvents and soil

Comparison of Engineering Education in Norway and China

Science.gov (United States)

Sun, Xiaodong; Jia, Yanrui; Li, Zhenchun; Song, Yu

2018-01-01

The Washington Accord is an internationally recognized agreement in engineering education of undergraduates. China joined the agreement as the 18th member country in 2016. The exploration technology and engineering major of China University of Petroleum has obtained the professional certification from international engineering education system and…

Eurisys: chemistry and petroleum as diversification centers

International Nuclear Information System (INIS)

Anon.

1996-01-01

The Eurisys Network has followed in 1995 its strategy of diversification and extended its engineering and servicing activities outside the nuclear domain towards other sectors such as the hydrocarbons sector. This development led to a 26% turnover increase (4.7 billions of French Francs (GF) in 1996 with respect to 3.8 GF in 1994) and a net result of 204 millions of Francs for the group. This short paper summarises the new servicing activities and contracts of the group in the petrochemistry, chemistry, petroleum and natural gas domain. (J.S.)

Ex-USSR: petroleum activities in 1991

International Nuclear Information System (INIS)

1992-01-01

This paper gives statistical data on economy and petroleum industry in ex-USSR: Primary energy production and consumption (coal, petroleum, natural gas, primary power), petroleum and natural gas reserves, drilling activity, exports and imports of petroleum products, refining capacity. 2 figs., 14 tabs

Engineering Education and Students' Challenges: Strategies toward Enhancing the Educational Environment in Engineering Colleges

Science.gov (United States)

Alkandari, Nabila Y.

2014-01-01

The main goal of this research is to gain an understanding of the challenges which have to be confronted by the engineering students at the College of Engineering and Petroleum at Kuwait University. The college has a large number of students, of which three hundred and eighty five were selected on a random basis for study purposes. The results…

Channeled Scaffolds for Engineering Myocardium with Mechanical Stimulation

Science.gov (United States)

Zhang, Ting; Wan, Leo Q.; Xiong, Zhuo; Marsano, Anna; Maidhof, Robert; Park, Miri; Yan, Yongnian; Vunjak-Novakovic, Gordana

2011-01-01

The characteristics of the matrix (composition, structure, mechanical properties) and external culture environment (pulsatile perfusion, physical stimulation) are critically important for engineering functional myocardial tissue. We report the development of chitosan-collagen scaffolds with micro-pores and an array of parallel channels (~200 μm in diameter) that were specifically designed for cardiac tissue engineering with mechanical stimulation. The scaffolds were designed to have the structural and mechanical properties similar to those of the native human heart matrix. Scaffolds were seeded with neonatal rat heart cells and subjected to dynamic tensile stretch using a custom-designed bioreactor. The channels enhanced oxygen transport and facilitated the establishment of cell connections within the construct. The myocardial patches (14 mm in diameter, 1–2 mm thick) consisted of metabolically active cells and started to contract synchronously after 3 days of culture. Mechanical stimulation with high tensile stresses promoted cell alignment, elongation, and the expression of connexin-43 (Cx-43). This study confirms the importance of scaffold design and mechanical stimulation for the formation of contractile cardiac constructs. PMID:22081518

Acoustic emission measurements in petroleum-related rock mechanics

Energy Technology Data Exchange (ETDEWEB)

Unander, Tor Erling

2002-07-01

Acoustic emission activity in rock has usually been studied in crystalline rock, which reflects that rock mechanics has also mostly been occupied with such rocks in relations to seismology, mining and tunneling. On the other hand, petroleum-related rock mechanics focuses on the behaviour of sedimentary rock. Thus, this thesis presents a general study of acoustic emission activity in sedimentary rock, primarily in sandstone. Chalk, limestone and shale have also been tested, but to much less degree because the AE activity in these materials is low. To simplify the study, pore fluids have not been used. The advent of the personal computer and computerized measuring equipment have made possible new methods both for measuring and analysing acoustic emissions. Consequently, a majority of this work is devoted to the development and implementation of new analysis techniques. A broad range of topics are treated: (1) Quantification of the AE activity level, assuming that the event rate best represents the activity. An algorithm for estimating the event rate and a methodology for objectively describing special changes in the activity e.g., onset determination, are presented. (2) Analysis of AE waveform data. A new method for determining the source energy of an AE event is presented, and it is shown how seismic source theory can be used to analyze even intermediate quality data. Based on these techniques, it is shown that a major part of the measured AE activity originates from a region close to the sensor, not necessarily representing the entire sample. (3) An improved procedure for estimating source locations is presented. The main benefit is a procedure that better handles arrival time data with large errors. Statistical simulations are used to quantify the uncertainties in the locations. The analysis techniques are developed with the application to sedimentary rock in mind, and in two articles, the techniques are used in the study of such materials. The work in the first

Latest progress of soft rock mechanics and engineering in China

Directory of Open Access Journals (Sweden)

Manchao He

2014-06-01

Full Text Available The progress of soft rock mechanics and associated technology in China is basically accompanied by the development of mining engineering and the increasing disasters of large rock deformation during construction of underground engineering. In this regard, Chinese scholars proposed various concepts and classification methods for soft rocks in terms of engineering practices. The large deformation mechanism of engineering soft rocks is to be understood through numerous experiments; and thus a coupled support theory for soft rock roadways is established, followed by the development of a new support material, i.e. the constant resistance and large deformation bolt/anchor with negative Poisson's ratio effect, and associated control technology. Field results show that large deformation problems related to numbers of engineering cases can be well addressed with this new technology, an effective way for similar soft rock deformation control.

The International Congress of Mechanical Engineering and Agricultural Sciences – CIIMCA 2013

International Nuclear Information System (INIS)

Remolina-Millán, Aduljay; Hernández-Arroyo, Emil

2014-01-01

The organizing committee of The International Congress of Mechanical Engineering and Agricultural Sciences – CIIMCA 2013 – are pleased to present CIIMCA-2013: the first international conference focused on subjects of materials science, mechanical engineering and renewable energy organized by Mechanical Engineering Faculty of the ''Universidad Pontificia Bolivariana'' in Bucaramanga, Colombia. This conference aims to be a place to produce discussions on whole topics of the congress, between the scientists of Colombia and the world. We strongly believe that knowledge is fundamental to the development of our countries. For that reason this multidisciplinary conference is looking forward to integrate engineering, agricultural science and nanoscience and nanotechnology to produce a synergy of this area of knowledge and to achieve scientific and technological developments. Agriculture is a very important topic for our conference; in Colombia, agricultural science needs more attention from the scientific community and the government. In the Faculty of Mechanical Engineering we are beginning to work on these issues to produce knowledge and improve the conditions in our country. The CIIMCA conference is a great opportunity to create interpersonal relationships and networks between scientists around the world. The interaction between scientists is very important in the process of the construction of knowledge. The general chairman encourages and invites you to make friends, relationships and participate strongly in the symposia and all program activities. PhD Aduljay Remolina-Millán Principal Chairman, International Mechanical Engineering and Agricultural Sciences Congress – CIIMCA Msc Emil Hernández-Arroyo Principal Chairman, International Mechanical Engineering and Agricultural Sciences Congress – CIIMCA Conferencephotograph Conferencephotograph 'Universidad Pontificia Bolivariana seccional Bucaramanga' host of the first

Investigating an effective supply chain for a refinery in a regulated petroleum sector

Directory of Open Access Journals (Sweden)

Chris Adendorf

2012-12-01

Full Text Available Currently, refined petroleum products are manufactured by six refineries in South Africa. The supply of refined petroleum products is supplemented by imports of refined petroleum products. These refined petroleum products are transported by pipeline, rail, road, sea and a combination thereof to depots across the country. These products are then distributed directly to commercial customers through points of resale in the form of retail service stations. The challenge is that the storage facilities and distribution networks in South Africa are currently utilised to its full capacity. There is a need to expand current storage infrastructure or to erect new storage facilities to facilitate imports. Durban Port that currently handles 70% of the country’s crude oil and 40% of refined products is also utilised to its full capacity. The investigated problem pertains to the limited storage and transport capacity available for the distribution of petroleum products in the country. The interview protocol, which was based on the literature reviewed, was used for compiling the primary data for the case study. Selected findings revealed that the respondents perceived that storage capacity is the most significant constraint militating against adequate supply by the supply chain. The findings also indicated that the respondents were of the opinion that transport rates and routes (cost of logistics are the greatest contributor to the prices of products. As a result, there appears to be a major scope for improvement in terms of the usage of pipelines and rails for the movement of petroleum products. Keywords: Petroleum products, storage facilities, supply chain, transportation, South African energy sector. Disciplines: civil engineering, architecture, business studies, energy studies

Project-Based Laboratory Experiences in Mechanical Engineering

Directory of Open Access Journals (Sweden)

Narendra Sharma

2011-12-01

Full Text Available In this paper we describe project-based laboratories in Mechanical Engineering designed to provide semester-long team experiences which mimic the real life industrial processes of design, development, testing and optimization. The labs are focused on courses at the sophomore level and thus require special attention to constraints of student backgrounds and experience. This paper describes laboratory projects in Dynamics and Fluid Mechanics.

The hidden face of the petroleum

International Nuclear Information System (INIS)

Laurent, E.

2006-02-01

For the first time, a book reveals what that was hidden to the public opinions: why the petroleum crisis of 1973 what only a manipulation, an arrangement between the OPEC and the petroleum companies, why the data concerning the petroleum reserves are wrong and increased by the producers countries, how Washington used the Saudi petroleum weapon to create the Soviet Union fall, and why from march 2001 maps of the Iraq (where were drawn the future petroleum explorations) were working documents for the vice President Cheney and petroleum managers for the ''secret society''. (A.L.B.)

A Comparison of the mechanical engineering and safety engineering student’s ICT attitudes at the Obuda University

Directory of Open Access Journals (Sweden)

Kiss Gabor

2016-01-01

Full Text Available Communication and technology are critical to education. However, using technology in education is not an easy task as communication barriers emerge. The aim of this research is to analyze the ICT attitudes from different faculties at the Obuda University that is between the mechanical engineering students and safety engineering students from the Donát Bánki Mechanical Safety Engineer Faculty. The students from these two groups will use different ICT tool at work after their graduation; the mechanical engineering students will work mostly with designer ICT tools, the safety engineering students will use security systems. It would be important to know whether instructors, when using ICT, have to follow different teaching methods and approaches in these two different groups or not. We measured the ICT attitude with a tool consisting of 23 items (Likert scaled. We worked with 361 students. The data analysis was performed with SPSS software using descriptive statistics and Mann-Whitney test. The results show both groups having the same positive ICT attitude however with one difference.

Petroleum industry in CIS

International Nuclear Information System (INIS)

Vaillaud, P.

1992-01-01

This paper gives statistical data on petroleum and natural gas industry in USSR and in Eastern Europe: crude oil and gas production, petroleum and natural gas deposits, exports, fuel consumption, pipelines network (total length, compressor or pump stations), petroleum refineries. This paper describes also air pollution (carbon dioxide and sulfur dioxide) and Environmental effects of coal and lignite using in fossil power plants in Eastern Europe. 17 figs., 7 tabs

Marks on the petroleum fiscality

International Nuclear Information System (INIS)

2007-02-01

This document offers some marks on the petroleum fiscality in France: the taxes as the 'accises' and the 'TVA', the part of the taxes in the sale price at the service station, the comparison with other countries of Europe, the tax revenues and the Government budget. It provides also marks on the fuels prices formation (margins), the world petroleum markets (supply and demand) and the part of the petroleum companies on the petroleum market. (A.L.B.)

Isolation of bacteria from mechanic workshops' soil environment ...

African Journals Online (AJOL)

PRECIOUS

2009-11-16

Nov 16, 2009 ... Key words: Used engine oil, contaminated soil, pollution. INTRODUCTION. Environmental pollution with petroleum and petroleum products (complex mixture of hydrocarbons) has been recognized as one of the most serious current problems especially when associated with accidental spills on large-scale.

Environmental control technology in petroleum drilling and production

International Nuclear Information System (INIS)

Wojtanowicz, A.K.

1997-01-01

Environmental control technology (ECT) is process integrated and relates mainly to pollution prevention and risk assessment. Mechanisms of environmental impact in petroleum drilling, well completion and production, include the generation of waste, induction of toxicity or the creation of pathways for pollutant migration. The identification and evaluation of these mechanisms constitute two parts of the scope of ECT. A third part is the development of new techniques to comply with environmental requirements without prejudicing productivity. The basic concepts of the ECT approach are presented in this chapter. The approach is then used to analyse oilfield drilling and production processes. Environmental control components developed in these technologies are described. These include: the control of the volume and toxicity of drilling fluids; source separation technology in produced water cleaning; subsurface injection of oilfield waste slurries; containment technology in the integrity of petroleum wells; subsurface reduction of produced water; oilfield pit closure technology. (37 figures; 26 tables; 227 references) (UK)

Apparatus for extracting petroleum

Energy Technology Data Exchange (ETDEWEB)

Coogan, J

1921-01-18

An apparatus for extracting petroleum from petroleum bearing sand or shale is described comprising a container for liquids, the container being divided into a plurality of compartments, an agitator mounted within the container and below the liquid level and having its forward end opening into one of the compartments, means for delivering sand or shale to the forward end of the agitator, means for subjecting the sand or shale to the action of a solvent for the petroleum while the sand or shale is being agitated and is submerged, the first-mentioned compartment being adapted to receive the extracted petroleum and means for removing the treated sand or shale from adjacent the rear end of the agitator.

Quantum mechanics for applied physics and engineering

CERN Document Server

Fromhold, Albert T

2011-01-01

This excellent text, directed to upper-level undergraduates and graduate students in engineering and applied physics, introduces the fundamentals of quantum mechanics, emphasizing those aspects of quantum mechanics and quantum statistics essential to an understanding of solid-state theory. A heavy background in mathematics and physics is not required beyond basic courses in calculus, differential equations, and calculus-based elementary physics.The first three chapters introduce quantum mechanics (using the Schrödinger equations), quantum statistics, and the free-electron theory of metals. Ch

Evaluation of quicklime mixing for the remediation of petroleum contaminated soils.

Science.gov (United States)

Schifano, V; Macleod, C; Hadlow, N; Dudeney, R

2007-03-15

Quicklime mixing is an established solidification/stabilization technique to improve mechanical properties and immobilise contaminants in soils. This study examined the effects of quicklime mixing on the concentrations and leachability of petroleum hydrocarbon compounds, in two natural soils and on a number of artificial sand/kaolinite mixtures. Several independent variables, such as clay content, moisture content and quicklime content were considered in the study. After mixing the soils with the quicklime, pH, temperature, moisture content, Atterberg limits and concentrations of petroleum hydrocarbon compounds were determined on soil and leachate samples extracted from the treated soils. Significant decreases in concentrations of petroleum hydrocarbon compounds were measured in soils and leachates upon quicklime mixing, which may be explained by a number of mechanisms such as volatilization, degradation and encapsulation of the hydrocarbon compounds promoted by the quicklime mixing. The increase in temperature due to the exothermic hydration reaction of quicklime when in contact with porewater helps to volatilize the light compounds but may not be entirely responsible for their concentration decreases and for the decrease of heavy aliphatics and aromatics concentrations.

Petroleum refining. Separation processes; Le raffinage du petrole. Procedes de separation

Energy Technology Data Exchange (ETDEWEB)

Wauquier, J.P. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Bonfils, P. [AB Industries (France); Company, J.P. [Compagnie de Raffinage et de Distribution TOTAL France, 75 - Paris (France); Deschamps, A. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Gourlia, J.P. [Elf Aquitaine (France); Gouzien, L. [Compagnie de Raffinage et de Distribution TOTAL France, 75 - Paris (France); Hombourger, T. [Mobil (France); Jullian, S. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Marty, C. [Compagnie de Raffinage et de Distribution TOTAL France, 75 - Paris (France); Mikitenko, P. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France); Ptak, C. [Technip, 92 - Rueil-Malmaison (France); Rojey, A.; Streicher, C.; Vidal, J. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

1998-12-01

After having given into details the conventional separation processes used in petroleum refining, the author describes the development future prospects: improvement of the existing technologies, introduction of new techniques or separation processes still not used today in this industry. This book is particularly devoted to students and to engineers and technical men who work in refineries. (O.M.) 308 refs.

The new challenges of petroleum

International Nuclear Information System (INIS)

Gernelle, E.

2006-02-01

Petroleum in in the center of our civilization: abundant, easy to use and energy powerful, it is used almost everywhere: transports, lighting, space heating, plastics, fertilizers, cloth industry etc. The 'black-gold' is the object of all stakes, from richness to power. However, petroleum is also at the origin of many evils: pollution, corruption, violence. Today, petroleum is a source of worries: how long will it last? How long will we be able to stand its impacts on environment? This book shades light on all these questions and supplies some concrete elements about this energy source. Content: technological challenges of petroleum; producers: powers and risks; consumers' dependence; to learn more about petroleum. (J.S.)

Fundamentals of Petroleum.

Science.gov (United States)

Bureau of Naval Personnel, Washington, DC.

Basic information on petroleum is presented in this book prepared for naval logistics officers. Petroleum in national defense is discussed in connection with consumption statistics, productive capacity, world's resources, and steps in logistics. Chemical and geological analyses are made in efforts to familiarize methods of refining, measuring,…

Analytical expression for an optimised link bar mechanism for a beta-type Stirling engine

DEFF Research Database (Denmark)

Carlsen, Henrik; Bovin, Jonas Kabell

2007-01-01

The design of a mechanism for kinematic beta-type Stirling engines, where the displacer piston and the working piston share the same cylinder, is complicated. A well-known solution is the rhombic drive, but this solution depends on oil lubrication because of the gear wheels connecting the two...... counter rotating crank shafts. In a hermetically sealed Stirling engine it is an advantage to avoid oil in the crank case, making the application of the rhombic drive difficult. In this paper, another crank mechanism is presented, which has been developed for a 9 kW single cylinder engine. The new crank...... mechanism is a further development of the mechanism in a previous 9 kW engine. The crank mechanism for the beta-type Stirling engine is based on two four-link straight line mechanisms pointing up and down, respectively. The mechanism pointing upwards is connected to the working piston, while the mechanism...

2002 Chemical Engineering Division annual report

International Nuclear Information System (INIS)

Lewis, D.; Graziano, D.; Miller, J. F.

2003-01-01

The Chemical Engineering Division is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. The Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory; Environment, Safety, and Health Analytical Chemistry services; and Dosimetry and Radioprotection services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors. Our wide-ranging expertise finds ready application in solving energy and environmental problems. Division personnel are frequently called on by

Incorporation of petroleum coke into red ceramic; Incorporacao de coque de petroleo em ceramica vermelha

Energy Technology Data Exchange (ETDEWEB)

Freitas, L.A. de; Monteiro, S.N.; Sanchez, R.; Vieira, C.M.F. [Laboratorio de Materiais Avancados - LAMAV, Universidade Estadual do Norte Fluminense Darcy Ribeiro - UENF, Campos dos Goytacazes, RJ (Brazil)], e-mails: sanchez@uenf.br, vieira@uenf.br

2011-04-15

This work has as its objective the evaluation of the effect of incorporation of petroleum coke in the physical and mechanical properties of red ceramic. Compositions were prepared with 0%, 1%, 2% and 4 wt.% of petroleum coke incorporated into a kaolinitic clayey body. Rectangular specimens were formed by extrusion to fire at 850 deg C and 1050 deg C. The determined physical and mechanical properties were flexural rupture strength and water absorption. The microstructure of the fired ceramics was evaluated by optical microscopy. The results show that the petroleum coke waste can significantly contribute to reduce the energy consumption during the firing stage. However, incorporations must be done in amounts around 1 wt.% to avoid deleterious effect on the water absorption of the ceramic. (author)

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT VI, MAINTAINING MECHANICAL GOVERNORS--DETROIT DIESEL ENGINES.

Science.gov (United States)

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF MECHANICAL GOVERNORS USED ON DIESEL ENGINES. TOPICS ARE (1) TYPES OF GOVERNORS AND ENGINE LOCATION, (2) GOVERNOR APPLICATIONS, (3) LIMITING SPEED MECHANICAL GOVERNOR, (4) VARIABLE SPEED MECHANICAL GOVERNOR, AND (5) CONSTANT SPEED…

Dynamic Mechanical and Nanofibrous Topological Combinatory Cues Designed for Periodontal Ligament Engineering.

Science.gov (United States)

Kim, Joong-Hyun; Kang, Min Sil; Eltohamy, Mohamed; Kim, Tae-Hyun; Kim, Hae-Won

2016-01-01

Complete reconstruction of damaged periodontal pockets, particularly regeneration of periodontal ligament (PDL) has been a significant challenge in dentistry. Tissue engineering approach utilizing PDL stem cells and scaffolding matrices offers great opportunity to this, and applying physical and mechanical cues mimicking native tissue conditions are of special importance. Here we approach to regenerate periodontal tissues by engineering PDL cells supported on a nanofibrous scaffold under a mechanical-stressed condition. PDL stem cells isolated from rats were seeded on an electrospun polycaprolactone/gelatin directionally-oriented nanofiber membrane and dynamic mechanical stress was applied to the cell/nanofiber construct, providing nanotopological and mechanical combined cues. Cells recognized the nanofiber orientation, aligning in parallel, and the mechanical stress increased the cell alignment. Importantly, the cells cultured on the oriented nanofiber combined with the mechanical stress produced significantly stimulated PDL specific markers, including periostin and tenascin with simultaneous down-regulation of osteogenesis, demonstrating the roles of topological and mechanical cues in altering phenotypic change in PDL cells. Tissue compatibility of the tissue-engineered constructs was confirmed in rat subcutaneous sites. Furthermore, in vivo regeneration of PDL and alveolar bone tissues was examined under the rat premaxillary periodontal defect models. The cell/nanofiber constructs engineered under mechanical stress showed sound integration into tissue defects and the regenerated bone volume and area were significantly improved. This study provides an effective tissue engineering approach for periodontal regeneration-culturing PDL stem cells with combinatory cues of oriented nanotopology and dynamic mechanical stretch.

Canadian petroleum history bibliography

Energy Technology Data Exchange (ETDEWEB)

Cass, D.

2003-09-27

The Petroleum History Bibliography includes a list of more than 2,000 publications that record the history of the Canadian petroleum industry. The list includes books, theses, films, audio tapes, published articles, company histories, biographies, autobiographies, fiction, poetry, humour, and an author index. It was created over a period of several years to help with projects at the Petroleum History Society. It is an ongoing piece of work, and as such, invites comments and additions.

Research Skills Enhancement in Future Mechanical Engineers

Directory of Open Access Journals (Sweden)

Jorge Lino Alves

2011-04-01

Full Text Available Nowadays, the Web is a common tool for students searching information about the subjects taught in the different university courses. Although this is a good tool for the first rapid knowledge, a deeper study is usually demanded.

After many years of teaching a course about ceramic and composite materials in the Integrated Master in Mechanical Engineering of Faculty of Engineering of University of Porto, Portugal, the authors used the Bologna reformulation of the mechanical engineering course to introduce new teaching methodologies based on a project based learning methodology.

One of the main innovations is a practical work that comprises the study of a recent ceramic scientific paper, using all the actual available tools, elaboration of a scientific report, work presentation and participation in a debate.

With this innovative teaching method the enrolment of the students was enhanced with a better knowledge about the ceramics subject and the skills related with the CDIO competences.

This paper presents the reasons for this implementation and explains the teaching methodology adopted as well as the changes obtained in the students’ final results.

Investing in Saskatchewan, sustaining energy development: proceedings of the 8. Saskatchewan petroleum conference

International Nuclear Information System (INIS)

1999-01-01

The theme of the 8. Saskatchewan Petroleum Conference 'Investing in Saskatchewan - Sustaining Energy Development' was explored in 33 papers presented in sessions on operations and facilities, reservoir engineering, exploration and development, improved oil recovery, fluid properties and phase behavior, well logging and completions and environmental concerns. Papers are indexed separately

Mathematical formulas for industrial and mechanical engineering

CERN Document Server

Kadry, Seifedine

2014-01-01

Mathematical Formulas For Industrial and Mechanical Engineering serves the needs of students and teachers as well as professional workers in engineering who use mathematics. The contents and size make it especially convenient and portable. The widespread availability and low price of scientific calculators have greatly reduced the need for many numerical tables that make most handbooks bulky. However, most calculators do not give integrals, derivatives, series and other mathematical formulas and figures that are often needed. Accordingly, this book contains that information in an easy way to

Petroleum marketing monthly, March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-10

This report for March 1995, provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly. A glossary is included.

Mechanisms of distinct activated carbon and biochar amendment effects on petroleum vapour biofiltration in soil.

Science.gov (United States)

Bushnaf, Khaled M; Mangse, George; Meynet, Paola; Davenport, Russell J; Cirpka, Olaf A; Werner, David

2017-10-18

We studied the effects of two percent by weight activated carbon versus biochar amendments in 93 cm long sand columns on the biofiltration of petroleum vapours released by a non-aqueous phase liquid (NAPL) source. Activated carbon greatly enhanced, whereas biochar slightly reduced, the biofiltration of volatile petroleum hydrocarbons (VPHs) over 430 days. Sorbent amendment benefitted the VPH biofiltration by retarding breakthrough during the biodegradation lag phase. Subsequently, sorbent amendment briefly reduced the mineralization of petroleum hydrocarbons by limiting their bioavailability. During the last and longest study period, when conditions became less supportive of microbial growth, because of inorganic nutrient scarcity, the sorbents again improved the pollution attenuation by preventing the degrading microorganisms from being overloaded with VPHs. A 16S rRNA gene based analysis showed sorbent amendment effects on soil microbial communities. Nocardioidaceae benefitted the most from petroleum hydrocarbons in activated carbon amended soil, whereas Pseudomonadacea predominated in unamended soil. Whilst the degrading microorganisms were overloaded with VPHs in the unamended soil, the reduced mobility and bioavailability of VPHs in the activated carbon amended soil led to the emergence of communities with higher specific substrate affinity, which removed bioavailable VPHs effectively at low concentrations. A numerical pollutant fate model reproduced these experimental observations by considering sorption effects on the pollutant migration and bioavailability for growth of VPH degrading biomass, which is limited by a maximum soil biomass carrying capacity. Activated carbon was a much stronger sorbent for VPHs than biochar, which explained the diverging effects of the two sorbents in this study.

Petroleum marketing annual, 1991

International Nuclear Information System (INIS)

1992-08-01

The Petroleum Marketing Annual contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates

Petroleum marketing annual 1993

International Nuclear Information System (INIS)

1995-01-01

The Petroleum Marketing Annual (PMA) contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board (f.o.b.) and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates

Petroleum marketing annual 1993

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

The Petroleum Marketing Annual (PMA) contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board (f.o.b.) and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates.

Mechanical stretching for tissue engineering: two-dimensional and three-dimensional constructs.

Science.gov (United States)

Riehl, Brandon D; Park, Jae-Hong; Kwon, Il Keun; Lim, Jung Yul

2012-08-01

Mechanical cell stretching may be an attractive strategy for the tissue engineering of mechanically functional tissues. It has been demonstrated that cell growth and differentiation can be guided by cell stretch with minimal help from soluble factors and engineered tissues that are mechanically stretched in bioreactors may have superior organization, functionality, and strength compared with unstretched counterparts. This review explores recent studies on cell stretching in both two-dimensional (2D) and three-dimensional (3D) setups focusing on the applications of stretch stimulation as a tool for controlling cell orientation, growth, gene expression, lineage commitment, and differentiation and for achieving successful tissue engineering of mechanically functional tissues, including cardiac, muscle, vasculature, ligament, tendon, bone, and so on. Custom stretching devices and lab-specific mechanical bioreactors are described with a discussion on capabilities and limitations. While stretch mechanotransduction pathways have been examined using 2D stretch, studying such pathways in physiologically relevant 3D environments may be required to understand how cells direct tissue development under stretch. Cell stretch study using 3D milieus may also help to develop tissue-specific stretch regimens optimized with biochemical feedback, which once developed will provide optimal tissue engineering protocols.

21 CFR 178.3710 - Petroleum wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Petroleum wax. 178.3710 Section 178.3710 Food and... and Production Aids § 178.3710 Petroleum wax. Petroleum wax may be safely used as a component of nonfood articles in contact with food, in accordance with the following conditions: (a) Petroleum wax is a...

Photoenhanced Toxicity of Petroleum to Aquatic Invertebrates and Fish

Science.gov (United States)

Photoenhanced toxicity is a distinct mechanism of petroleum toxicity that is mediated by the interaction of solar radiation with specific polycyclic aromatic compounds in oil. Phototoxicity is observed as a twofold to greater than 1000-fold increase in chemical toxicity to aquati...

High paraffin Kumkol petroleum processing under fuel and lubricant petroleum scheme

International Nuclear Information System (INIS)

Nadirov, N.K.; Konaev, Eh.N.

1997-01-01

Technological opportunity of high paraffin Kumkol petroleum processing under the fuel and lubricant scheme with production of lubricant materials in short supply, combustible materials and technical paraffin is shown. Mini petroleum block putting into operation on Kumkol deposit is reasonable economically and raises profitableness of hydrocarbon raw material production. (author)

Energy Saving Separations Technologies for the Petroleum Industry: An Industry-University-National Laboratory Research Partnership

Energy Technology Data Exchange (ETDEWEB)

Dorgan, John R.; Stewart, Frederick F.; Way, J. Douglas

2003-03-28

This project works to develop technologies capable of replacing traditional energy-intensive distillations so that a 20% improvement in energy efficiency can be realized. Consistent with the DOE sponsored report, Technology Roadmap for the Petroleum Industry, the approach undertaken is to develop and implement entirely new technology to replace existing energy intensive practices. The project directly addresses the top priority issue of developing membranes for hydrocarbon separations. The project is organized to rapidly and effectively advance the state-of-the-art in membranes for hydrocarbon separations. The project team includes ChevronTexaco and BP, major industrial petroleum refiners, who will lead the effort by providing matching resources and real world management perspective. Academic expertise in separation sciences and polymer materials found in the Chemical Engineering and Petroleum Refining Department of the Colorado School of Mines is used to invent, develop, and test new membrane materials. Additional expertise and special facilities available at the Idaho National Engineering and Environmental Laboratory (INEEL) are also exploited in order to effectively meet the goals of the project. The proposed project is truly unique in terms of the strength of the team it brings to bear on the development and commercialization of the proposed technologies.

Channelled scaffolds for engineering myocardium with mechanical stimulation.

Science.gov (United States)

Zhang, Ting; Wan, Leo Q; Xiong, Zhuo; Marsano, Anna; Maidhof, Robert; Park, Miri; Yan, Yongnian; Vunjak-Novakovic, Gordana

2012-10-01

The characteristics of the matrix (composition, structure, mechanical properties) and external culture environment (pulsatile perfusion, physical stimulation) of the heart are important characteristics in the engineering of functional myocardial tissue. This study reports on the development of chitosan-collagen scaffolds with micropores and an array of parallel channels (~ 200 µm in diameter) that were specifically designed for cardiac tissue engineering using mechanical stimulation. The scaffolds were designed to have similar structural and mechanical properties of those of native heart matrix. Scaffolds were seeded with neonatal rat heart cells and subjected to dynamic tensile stretch using a custom designed bioreactor. The channels enhanced oxygen transport and facilitated the establishment of cell connections within the construct. The myocardial patches (14 mm in diameter, 1-2 mm thick) consisted of metabolically active cells that began to contract synchronously after 3 days of culture. Mechanical stimulation with high tensile stress promoted cell alignment, elongation, and expression of connexin-43 (Cx-43). This study confirms the importance of scaffold design and mechanical stimulation for the formation of contractile cardiac constructs. Copyright © 2011 John Wiley & Sons, Ltd.

Canadian Petroleum Products Inst. annual report, 1991

International Nuclear Information System (INIS)

1992-01-01

The Canadian Petroleum Products Institute (CPPI) was created in 1989 as a nonprofit association of Canadian refiners and marketers of petroleum products. In 1991, the Atlantic Petroleum Association, the Quebec Petroleum Association, the Ontario Petroleum Association, the Canada West Petroleum Association, and the Petroleum Association for Conservation of the Canadian Environment (PACE) were integrated into the CPPI. The objective of the CPPI is to serve and represent the refining and marketing sectors of the petroleum industry with respect to environment, health and safety, and business issues. An industry overview is provided, as well as highlights of environmental achievements and challenges, and economics and operations for the year. Lists of CPPI publications, standing committees, and officers are also included. 9 figs

Reducing barriers to energy efficiency in the German mechanical engineering sector. Executive summary

Energy Technology Data Exchange (ETDEWEB)

Schleich, J.; Boede, U.

2000-12-01

This report describes the empirical research into barriers to energy efficiency in the German mechanical engineering (ME) sector. It is one of nine such reports in the BARRIERS project. The report contains description and analysis of four case studies of energy management in German companies in the ME sector. The results are analysed using the theoretical framework developed for the BARRIERS project. The report also provides brief recommendations on how these barriers to the rational use of energy (RUE) may be overcome and how energy efficiency within the ME sector may be improved. The results of the study for the ME sector in Germany are summarised in this executive summary under the following headings: - Characterising the mechanical engineering sector; - Case studies of energy management in the German mechanical engineering sector; - Evidence of barriers in the German mechanical engineering sector; - The role of energy service companies in the mechanical engineering sector; - Policy implications. (orig.)

Reducing barriers to energy efficiency in the German mechanical engineering sector. Final report

Energy Technology Data Exchange (ETDEWEB)

Schleich, J.; Boede, U.

2000-12-01

This report describes the empirical research into barriers to energy efficiency in the German mechanical engineering (ME) sector. It is one of nine such reports in the BARRIERS project. The report contains description and analysis of four case studies of energy management in German companies in the ME sector. The results are analysed using the theoretical framework developed for the BARRIERS project. The report also provides brief recommendations on how these barriers to the rational use of energy (RUE) may be overcome and how energy efficiency within the ME sector may be improved. The results of the study for the ME sector in Germany are summarised in this executive summary under the following headings: - Characterising the mechanical engineering sector; - Case studies of energy management in the German mechanical engineering sector; - Evidence of barriers in the German mechanical engineering sector; - The role of energy service companies in the mechanical engineering sector; - Policy implications. (orig.)

Mechanical stimulation in the engineering of heart muscle.

Science.gov (United States)

Liaw, Norman Yu; Zimmermann, Wolfram-Hubertus

2016-01-15

Recreating the beating heart in the laboratory continues to be a formidable bioengineering challenge. The fundamental feature of the heart is its pumping action, requiring considerable mechanical forces to compress a blood filled chamber with a defined in- and outlet. Ventricular output crucially depends on venous loading of the ventricles (preload) and on the force generated by the preloaded ventricles to overcome arterial blood pressure (afterload). The rate of contraction is controlled by the spontaneously active sinus node and transmission of its electrical impulses into the ventricles. The underlying principles for these physiological processes are described by the Frank-Starling mechanism and Bowditch phenomenon. It is essential to consider these principles in the design and evaluation of tissue engineered myocardium. This review focuses on current strategies to evoke mechanical loading in hydrogel-based heart muscle engineering. Copyright © 2015. Published by Elsevier B.V.

Petroleum Sector (NAICS 324)

Science.gov (United States)

Find relevant environmental regulations for the petroleum industry (NAICS 324), including National Emission Standards for Hazardous Air Pollutants (NESHAP)s for petroleum refineries and gasoline dispensing & effluent guidelines for oil and gas extraction

Mechanical Engineering Department. Technical review

Energy Technology Data Exchange (ETDEWEB)

Simecka, W.B.; Condouris, R.A.; Talaber, C. (eds.)

1980-01-01

The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work.

Mechanical engineering department technical review

International Nuclear Information System (INIS)

Carr, R.B.; Denney, R.M.

1981-01-01

The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work

Mechanical Engineering Department. Technical review

International Nuclear Information System (INIS)

Simecka, W.B.; Condouris, R.A.; Talaber, C.

1980-01-01

The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work

Theoretical Background for Predicting the Properties of Petroleum Fluids via Group Contribution Methods

Czech Academy of Sciences Publication Activity Database

Bogdanić, Grozdana; Pavlíček, Jan; Wichterle, Ivan

2012-01-01

Roč. 42, SI (2012), s. 1873-1878 E-ISSN 1877-7058. [International Congress of Chemical and Process Engineering CHISA 2012 and 15th Conference PRES 2012 /20./. Prague, 25.08.2012-29.08.2012] Institutional support: RVO:67985858 Keywords : petroleum fluids * prediction * physico-chemical properties Subject RIV: CF - Physical ; Theoretical Chemistry

Fabrication and study of stability of Ca2AlWO5,5 ceramic in crude petroleum for applications in petroleum industry

International Nuclear Information System (INIS)

Yadava, Y.P.; Silva, N.D.G.; Sousa, A.G. de; Sanguinetti Ferreira, R.A.

2010-01-01

Perovskite-type ceramic oxides or their derivatives are used for applications in high technology because of their enormous range of physic-chemical properties with little change in structural characteristics. In this paper we report manufacture ceramic components of a new ceramic Ca 2 AlWO 5,5 by thermo-mechanical process. Stoichiometric amounts of chemical constituents with high degree of purity, were homogenized using a ball mill and high purity alumina balls, compacted by uniaxial pressing and annealed at 1200 deg C for 48 hours. The structural characterization studied by x-ray diffraction that this material has a typical complex ordered cubic perovskite structure. For the study the stability of these ceramics in crude petroleum circular discs of 20 mm diameter and 2 mm thickness were produced and sintering. These discs were submerged in crude petroleum for 15, 30 and 45 days and were examined at each stage by X-ray diffraction, optical microscopy and hardness testing and these results show that Ca 2 AlWO 5,5 are stable in crude petroleum environment. (author)

Facts 2009 - The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

2009-07-01

The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Contents: Foreword; The petroleum sector; Norwegian resource management; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology; Environmental considerations; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

PREFACE: 3rd International Conference of Mechanical Engineering Research (ICMER 2015)

Science.gov (United States)

Mamat, Riazalman; Rahman, Mustafizur; Mohd. Zuki Nik Mohamed, Nik; Che Ghani, Saiful Anwar; Harun, Wan Sharuzi Wan

2015-12-01

The 3rd ICMER2015 is the continuity of the NCMER2010. The year 2010 represents a significant milestone in the history for Faculty of Mechanical Engineering, Universiti Malaysia Pahang (UMP) Malaysia with the organization of the first and second national level conferences (1st and 2nd NCMER) at UMP on May 26-27 and Dec 3-4 2010. The Faculty then changed the name from National Conference on Mechanical Engineering Research (NCMER) to International Conference on Mechanical Engineering Research (ICMER) in 2011 and this year, 2015 is our 3rd ICMER. These proceedings contain the selected scientific manuscripts submitted to the conference. It is with great pleasure to welcome you to the "International Conference on Mechanical Engineering Research (ICMER2015)" that is held at Zenith Hotel, Kuantan, Malaysia. The call for papers attracted submissions of over two hundred abstracts from twelve different countries including Japan, Iran, China, Kuwait, Indonesia, Norway, Philippines, Morocco, Germany, UAE and more. The scientific papers published in these proceedings have been revised and approved by the technical committee of the 3rd ICMER2015. All of the papers exhibit clear, concise, and precise expositions that appeal to a broad international readership interested in mechanical engineering, combustion, metallurgy, materials science as well as in manufacturing and biomechanics. The reports present original ideas or results of general significance supported by clear reasoning and compelling evidence, and employ methods, theories and practices relevant to the research. The authors clearly state the questions and the significance of their research to theory and practice, describe how the research contributes to new knowledge, and provide tables and figures that meaningfully add to the narrative. In this edition of ICMER representatives attending are from academia, industry, governmental and private sectors. The plenary and invited speakers will present, discuss, promote and

Formula Student as Part of a Mechanical Engineering Curriculum

Science.gov (United States)

Davies, Huw Charles

2013-01-01

Formula Student (FS) is a multi-university student design competition managed by the UK Institution of Mechanical Engineers. Students are required to demonstrate and prove their creativity and engineering skills through the design, manufacture and financing of a small formula style race car. This paper seeks to explore the educational value that…

Mechanical Engineering Department technical abstracts for the period January-June 1985

International Nuclear Information System (INIS)

Woo, H.H.

1986-01-01

This document contains the abstracts from 116 reports produced by the Mechanical Engineering Department of the Lawrence Livermore National Laboratory during the period January - June, 1985. The Mechanical Engineering Department is reponsible for the design, analysis, fabrication, testing, and field installation of all mechanical components and systems required by Defence Systems, Lasers, Magnetic Fusion Energy, Physics, and Biomedical and Environmental Research. Similar support is provided to the Chemistry and Computation Departments. Keyword, author, and report-number indices are included

Financing petroleum agreements

International Nuclear Information System (INIS)

Robson, C.J.V.

1994-01-01

This chapter describes the typical type of financing agreements which are currently used to finance North Sea petroleum projects whether they are in the cause of development or have been developed and are producing. It deals with the agreements which are entered into to finance borrowings for petroleum projects on a non-resource or limited resource basis. (UK)

Applied Geophysics Opportunities in the Petroleum Industry

Science.gov (United States)

Olgaard, D. L.; Tikku, A.; Roberts, J. C.; Martinez, A.

2012-12-01

Meeting the increasing global demand for energy over the next several decades presents daunting challenges to engineers and scientists, including geoscientists of all disciplines. Many opportunities exist for geophysicists to find and produce oil and gas in a safe, environmentally responsible and affordable manner. Successful oil and gas exploration involves a 'Plates to Pores' approach that integrates multi-scale data from satellites, marine and land seismic and non-seismic field surveys, lab experiments, and even electron microscopy. The petroleum industry is at the forefront of using high performance computing to develop innovative methods to process and analyze large volumes of seismic data and perform realistic numerical modeling, such as finite element fluid flow and rock deformation simulations. Challenging and rewarding jobs in exploration, production and research exist for students with BS/BA, MS and PhD degrees. Geophysics students interested in careers in the petroleum industry should have a broad foundation in science, math and fundamental geosciences at the BS/BA level, as well as mastery of the scientific method, usually gained through thesis work at MS and PhD levels. Field geology or geophysics experience is also valuable. Other personal attributes typical for geoscientists to be successful in industry include a passion for solving complex geoscience problems, the flexibility to work on a variety of assignments throughout a career and skills such as teamwork, communication, integration and leadership. In this presentation we will give examples of research, exploration and production opportunities for geophysicists in petroleum companies and compare and contrast careers in academia vs. industry.

Petroleum marketing annual, 1990

International Nuclear Information System (INIS)

1991-01-01

The Petroleum Marketing Annual contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. (VC)

Reference data about petroleum fiscality

International Nuclear Information System (INIS)

2006-01-01

This paper explains the different taxes existing in France for the petroleum products (domestic tax on petroleum products, added-value tax), the share of taxes in the retail price, the differences with other European countries, the French Government fiscal receipts and budget. Some information forms are attached to this document and concern: the formation of fuel prices (upstream, refining and transport-distribution margins), the evolution of annual average transport-distribution margins, some reference data about world petroleum markets (supply and demand, prices, market data), and some reference data about the role of oil companies on the petroleum market. (J.S.)

A study on an electronically controlled liquefied petroleum gas diesel dual-fuel automobile

Energy Technology Data Exchange (ETDEWEB)

Chunhua Zhang; Yaozhang Bian; Lizeng Si; Junzhi Liao; Odbileg, N. [Chang' an Univ., Automobile Faculty, Xi' an (China)

2005-02-15

In this paper, the control scheme of a liquefied petroleum gas (LPG)-diesel dual-fuel engine with electronic control is illustrated, the external characteristics and load characteristics of the LPG-diesel dual-fuel engine and the diesel engine are compared and analysed, and the results of automobile road tests are also given. The experimental results show that, compared with diesel, the output performance of dual fuel is not reduced, while smoke emission of dual fuel is significantly reduced, NO{sub x} emission of dual fuel is hardly changed, but HC emission and CO emission of dual fuel are increased and fuel consumption of dual fuel is reduced. (Author)

Mechanical testing of hydrogels in cartilage tissue engineering: beyond the compressive modulus.

Science.gov (United States)

Xiao, Yinghua; Friis, Elizabeth A; Gehrke, Stevin H; Detamore, Michael S

2013-10-01

Injuries to articular cartilage result in significant pain to patients and high medical costs. Unfortunately, cartilage repair strategies have been notoriously unreliable and/or complex. Biomaterial-based tissue-engineering strategies offer great promise, including the use of hydrogels to regenerate articular cartilage. Mechanical integrity is arguably the most important functional outcome of engineered cartilage, although mechanical testing of hydrogel-based constructs to date has focused primarily on deformation rather than failure properties. In addition to deformation testing, as the field of cartilage tissue engineering matures, this community will benefit from the addition of mechanical failure testing to outcome analyses, given the crucial clinical importance of the success of engineered constructs. However, there is a tremendous disparity in the methods used to evaluate mechanical failure of hydrogels and articular cartilage. In an effort to bridge the gap in mechanical testing methods of articular cartilage and hydrogels in cartilage regeneration, this review classifies the different toughness measurements for each. The urgency for identifying the common ground between these two disparate fields is high, as mechanical failure is ready to stand alongside stiffness as a functional design requirement. In comparing toughness measurement methods between hydrogels and cartilage, we recommend that the best option for evaluating mechanical failure of hydrogel-based constructs for cartilage tissue engineering may be tensile testing based on the single edge notch test, in part because specimen preparation is more straightforward and a related American Society for Testing and Materials (ASTM) standard can be adopted in a fracture mechanics context.

Mechanical Engineering | Classification | College of Engineering & Applied

Science.gov (United States)

Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

Phytoremediation of petroleum contaminated soils by Mirabilis Jalapa L. in a greenhouse plot experiment.

Science.gov (United States)

Peng, Shengwei; Zhou, Qixing; Cai, Zhang; Zhang, Zhineng

2009-09-15

Phytoremediation of soils contaminated by organic chemicals is a challenging problem in environmental science and engineering. On the basis of identifying remediation plants from ornamentals, the remediation capability of Mirabilis Jalapa L. to treat petroleum contaminated soil from the Shengli Oil Field in Dongying City, Shandong Province, China was further investigated using a field plot experiment carried out in a greenhouse. The results showed that the average efficiency of removing total petroleum hydrocarbons (TPHs) by M. jalapa over the 127-day culture period was high, up to 41.61-63.20%, when the removal rate by natural attenuation was only 19.75-37.92%. The maximum reduction occurred in the saturated hydrocarbon fraction compared with other components of petroleum contaminants. According to the qualitative and quantitative parameters including plant height, fresh weight, dry weight, root length, root weight and visual stress symptoms, it was indicated that M. jalapa had a peculiar tolerance to petroleum contamination and could effectively promote the degradation of TPHs when the concentration of petroleum hydrocarbons in soil was equal to and lower than 10,000 mg/kg. The population of living microorganisms in the planted soil could be also adaptive to contaminated soil. On the whole, M. jalapa is a widely spread species that can be effectively applied to phytoremediation of contaminated soil.

Petroleum supply annual 1992

International Nuclear Information System (INIS)

1993-01-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1992 through annual and monthly surveys. The PSA is divided into two volumes. The first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. This second volume contains final statistics for each month of 1992, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Explanatory Notes, located at the end of this publication, present information describing data collection, sources, estimation methodology, data quality control procedures, modifications to reporting requirements and interpretation of tables. Industry terminology and product definitions are listed alphabetically in the Glossary

15 CFR Supplement No. 1 to Part 754 - Petroleum and Petroleum Products

Science.gov (United States)

2010-01-01

... fuel (including tractor fuel and stationary turbine fuel). 2710.00.2000 Kerosene derived from petroleum... medicinal grade derived from petroleum, shale oil or both. 3819.00.0000 Hydraulic fluids, including... lubricating oil. 2710.00.3030 Turbine lubricating oil, including marine. 2710.00.3040 Automotive gear oils...

Petroleum investment in Kazakhstan

International Nuclear Information System (INIS)

Friedrich, M.

1994-01-01

There is no specific petroleum legislation as such in place in Kazakhstan and tax legislation is unsophisticated. Regulation of operations is subject to generally applicable legislation. A brief account of the difficulties which exist for both sides in renegotiating a contract is given. Since the competence to enter into contracts with foreign companies has not been fully defined, the first problem when applying for petroleum rights is the identification of a negotiating partner. A summary of terms and conditions and a list of the main laws applicable to petroleum operations are included. (UK)

Petroleum marketing monthly with data for April 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-05

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data on the Petroleum Marketing Monthly. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in the Petroleum Marketing Monthly in five sections: Summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption.

Superconducting Qubits as Mechanical Quantum Engines.

Science.gov (United States)

Sachtleben, Kewin; Mazon, Kahio T; Rego, Luis G C

2017-09-01

We propose the equivalence of superconducting qubits with a pistonlike mechanical quantum engine. The work reports a study on the nature of the nonequilibrium work exchanged with the quantum-nonadiabatic working medium, which is modeled as a multilevel coupled quantum well system subject to an external control parameter. The quantum dynamics is solved for arbitrary control protocols. It is shown that the work output has two components: one that depends instantaneously on the level populations and another that is due to the quantum coherences built in the system. The nonadiabatic coherent dynamics of the quantum engine gives rise to a resistance (friction) force that decreases the work output. We consider the functional equivalence of such a device and a rf-SQUID flux qubit.

Jet Engines as High-Capacity Vacuum Pumps

Science.gov (United States)

Wojciechowski, C. J.

1983-01-01

Large diffuser operations envelope and long run times possible. Jet engine driven ejector/diffuser system combines two turbojet engines and variable-area-ratio ejector in two stages. Applications in such industrial proesses as handling corrosive fumes, evaporation of milk and fruit juices, petroleum distillation, and dehydration of blood plasma and penicillin.

Petroleum Supply Monthly, September 1990. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

Whited, D.; Jacobus, P. (eds.)

1990-11-28

Data presented in this PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 46 tabs.

Petroleum supply monthly, October 1990. [Contains Glossary

Energy Technology Data Exchange (ETDEWEB)

1990-12-27

Data presented in this report describes the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. 12 figs., 54 tabs.

Cell Patterning for Liver Tissue Engineering via Dielectrophoretic Mechanisms

Directory of Open Access Journals (Sweden)

Wan Nurlina Wan Yahya

2014-07-01

Full Text Available Liver transplantation is the most common treatment for patients with end-stage liver failure. However, liver transplantation is greatly limited by a shortage of donors. Liver tissue engineering may offer an alternative by providing an implantable engineered liver. Currently, diverse types of engineering approaches for in vitro liver cell culture are available, including scaffold-based methods, microfluidic platforms, and micropatterning techniques. Active cell patterning via dielectrophoretic (DEP force showed some advantages over other methods, including high speed, ease of handling, high precision and being label-free. This article summarizes liver function and regenerative mechanisms for better understanding in developing engineered liver. We then review recent advances in liver tissue engineering techniques and focus on DEP-based cell patterning, including microelectrode design and patterning configuration.

Selling petroleum to the military

International Nuclear Information System (INIS)

Uscher, R.H.

1999-01-01

This article examines what petroleum products and services the US military buys, the contracts awarded to Asian and European refiners for supplies outside the USA, and military specifications and test methods including the specifications of JP-8 battlefield fuel and the JP-8+100 additive package for military aircraft. The way in which the military buys petroleum products is described, and details are given of the types of military contracts, the bidding on Defense Energy Support Center (DESC) petroleum contracts, the performance of military petroleum contracts, socio-economic programmes, the Prompt Payment Act requiring contractors to be paid promptly, and procedures for claims and disputes

Advances in Application of Mechanical Stimuli in Bioreactors for Cartilage Tissue Engineering.

Science.gov (United States)

Li, Ke; Zhang, Chunqiu; Qiu, Lulu; Gao, Lilan; Zhang, Xizheng

2017-08-01

Articular cartilage (AC) is the weight-bearing tissue in diarthroses. It lacks the capacity for self-healing once there are injuries or diseases due to its avascularity. With the development of tissue engineering, repairing cartilage defects through transplantation of engineered cartilage that closely matches properties of native cartilage has become a new option for curing cartilage diseases. The main hurdle for clinical application of engineered cartilage is how to develop functional cartilage constructs for mass production in a credible way. Recently, impressive hyaline cartilage that may have the potential to provide capabilities for treating large cartilage lesions in the future has been produced in laboratories. The key to functional cartilage construction in vitro is to identify appropriate mechanical stimuli. First, they should ensure the function of metabolism because mechanical stimuli play the role of blood vessels in the metabolism of AC, for example, acquiring nutrition and removing wastes. Second, they should mimic the movement of synovial joints and produce phenotypically correct tissues to achieve the adaptive development between the micro- and macrostructure and function. In this article, we divide mechanical stimuli into three types according to forces transmitted by different media in bioreactors, namely forces transmitted through the liquid medium, solid medium, or other media, then we review and summarize the research status of bioreactors for cartilage tissue engineering (CTE), mainly focusing on the effects of diverse mechanical stimuli on engineered cartilage. Based on current researches, there are several motion patterns in knee joints; but compression, tension, shear, fluid shear, or hydrostatic pressure each only partially reflects the mechanical condition in vivo. In this study, we propose that rolling-sliding-compression load consists of various stimuli that will represent better mechanical environment in CTE. In addition, engineers

A high throughput mechanical screening device for cartilage tissue engineering.

Science.gov (United States)

Mohanraj, Bhavana; Hou, Chieh; Meloni, Gregory R; Cosgrove, Brian D; Dodge, George R; Mauck, Robert L

2014-06-27

Articular cartilage enables efficient and near-frictionless load transmission, but suffers from poor inherent healing capacity. As such, cartilage tissue engineering strategies have focused on mimicking both compositional and mechanical properties of native tissue in order to provide effective repair materials for the treatment of damaged or degenerated joint surfaces. However, given the large number design parameters available (e.g. cell sources, scaffold designs, and growth factors), it is difficult to conduct combinatorial experiments of engineered cartilage. This is particularly exacerbated when mechanical properties are a primary outcome, given the long time required for testing of individual samples. High throughput screening is utilized widely in the pharmaceutical industry to rapidly and cost-effectively assess the effects of thousands of compounds for therapeutic discovery. Here we adapted this approach to develop a high throughput mechanical screening (HTMS) system capable of measuring the mechanical properties of up to 48 materials simultaneously. The HTMS device was validated by testing various biomaterials and engineered cartilage constructs and by comparing the HTMS results to those derived from conventional single sample compression tests. Further evaluation showed that the HTMS system was capable of distinguishing and identifying 'hits', or factors that influence the degree of tissue maturation. Future iterations of this device will focus on reducing data variability, increasing force sensitivity and range, as well as scaling-up to even larger (96-well) formats. This HTMS device provides a novel tool for cartilage tissue engineering, freeing experimental design from the limitations of mechanical testing throughput. © 2013 Published by Elsevier Ltd.

Introduction to Analytical Methods for Internal Combustion Engine Cam Mechanisms

CERN Document Server

Williams, J J

2013-01-01

Modern design methods of Automotive Cam Design require the computation of a range of parameters. This book provides a logical sequence of steps for the derivation of the relevant equations from first principles, for the more widely used cam mechanisms. Although originally derived for use in high performance engines, this work is equally applicable to the design of mass produced automotive and other internal combustion engines.   Introduction to Analytical Methods for Internal Combustion Engine Cam Mechanisms provides the equations necessary for the design of cam lift curves with an associated smooth acceleration curve. The equations are derived for the kinematics and kinetics of all the mechanisms considered, together with those for cam curvature and oil entrainment velocity. This permits the cam shape, all loads, and contact stresses to be evaluated, and the relevant tribology to be assessed. The effects of asymmetry on the manufacture of cams for finger follower and offset translating curved followers is ...

77 FR 42297 - National Petroleum Council

Science.gov (United States)

2012-07-18

... DEPARTMENT OF ENERGY National Petroleum Council AGENCY: Department of Energy, Office of Fossil... National Petroleum Council. The Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires that... Matters Discussion of Any Other Business Properly Brought Before the National Petroleum Council...

76 FR 53889 - National Petroleum Council

Science.gov (United States)

2011-08-30

... DEPARTMENT OF ENERGY National Petroleum Council AGENCY: Department of Energy, Office of Fossil... Petroleum Council. The Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires that public... Properly Brought Before the National, Petroleum Council, Adjournment. Public Participation: The meeting is...

Petroleum supply monthly, October 1991. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

1991-10-30

Data presented in this report describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importer, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics 14 figs., 56 tabs.

Petroleum supply monthly - with data for May 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. This document contains a glossary.

Petroleum supply monthly with data from April 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum and international policy

International Nuclear Information System (INIS)

Pertuzio, A.

2002-01-01

To illustrate the relation between the petroleum and the international policy, the author presents the place of the petroleum industry in the international relations by an analysis of the historical aspects, the states and international organizations interventions and the prices evolution. (A.L.B.)

Petroleum systems of Indonesia

NARCIS (Netherlands)

Doust, H.; Noble, R.A.

2008-01-01

Indonesia contains many Tertiary basins, several of which have proven to be very prolific producers of oil and gas. The geology and petroleum systems of these productive basins are reviewed, summarized and updated according to the most recent developments. We have linked the recognized petroleum

Caspian sea: petroleum challenges

International Nuclear Information System (INIS)

2005-01-01

The Caspian sea is one of the world areas the most promising in terms of investments and petroleum development. This study presents the petroleum challenges generated by this hydrocarbons reserve. The first part discusses the juridical status (sea or lake), the petroleum and the gas reserves, the ecosystem and the today environment (fishing and caviar), the geostrategic situation and the transport of gas and oil. It provides also a chronology from 1729 to 2005, a selection of Internet sites, books and reports on the subject and identity sheets of the countries around the Caspian sea. (A.L.B.)

Petroleum: the new deal

International Nuclear Information System (INIS)

Magalhaes, St.; Kan, E.

2008-01-01

The drop of oil prices imposes a revision of development and investment strategies of petroleum and para-petroleum companies, while technologies under study try to optimize the exploration and production costs. Following the financial and economical crises, the petroleum industry is preparing its restructuring: new profitability threshold of projects, slowing down of the activity, expected surge of mergers. Despite the crisis, the R and D for the exploitation of tar sands still goes on while on the offshore side, R and D has never been so active to take up the challenge of extreme deep sea conditions. (J.S.)

Basic petroleum research. Final report

International Nuclear Information System (INIS)

Roesjoe, Bjarne; Stiksrud, Helge

2004-01-01

An overview of projects in the field of basic petroleum research (PetroForsk) is presented. A brief presentation of some of the projects is included, as well as political comments on the value of these projects. The research program Basic Petroleum Research (PetroForsk) was established in 1998 and ended in 2004. The program has been part of the Research Council of Norway's long-term effort in petroleum research (ml)

78 FR 40131 - National Petroleum Council

Science.gov (United States)

2013-07-03

... DEPARTMENT OF ENERGY National Petroleum Council AGENCY: Office of Fossil Energy, Department of... Petroleum Council. The Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires that public... Administrative Matters Discussion of Any Other Business Properly Brought Before the National Petroleum Council...

REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

Energy Technology Data Exchange (ETDEWEB)

Kevin C. Galbreath; Donald L. Toman; Christopher J. Zygarlicke

1999-09-01

Petroleum coke, a byproduct of the petroleum-refining process, is an attractive primary or supplemental fuel for power production primarily because of a progressive and predictable increase in the production volumes of petroleum coke (1, 2). Petroleum coke is most commonly blended with coal in proportions suitable to meet sulfur emission compliance. Petroleum coke is generally less reactive than coal; therefore, the cofiring of petroleum coke with coal typically improves ignition, flame stability, and carbon loss relative to the combustion of petroleum coke alone. Although petroleum coke is a desirable fuel for producing relatively inexpensive electrical power, concerns about the effects of petroleum coke blending on combustion and pollution control processes exist in the coal-fired utility industry (3). The Energy & Environmental Research Center (EERC) completed a 2-year technical assessment of petroleum coke as a supplemental fuel. A survey questionnaire was sent to seven electric utility companies that are currently cofiring coal and petroleum coke in an effort to solicit specific suggestions on research needs and fuel selections. An example of the letter and survey questionnaire is presented in Appendix A. Interest was expressed by most utilities in evaluating the effects of petroleum coke blending on grindability, combustion reactivity, fouling, slagging, and fly ash emissions control. Unexpectedly, concern over corrosion was not expressed by the utilities contacted. Although all seven utilities responded to the question, only two utilities, Northern States Power Company (NSP) and Ameren, sent fuels to the EERC for evaluation. Both utilities sent subbituminous coals from the Power River Basin and petroleum shot coke samples. Petroleum shot coke is produced unintentionally during operational upsets in the petroleum refining process. This report evaluates the effects of petroleum shot coke blending on grindability, fuel reactivity, fouling/slagging, and

Fact sheet. Norwegian petroleum activity 1996

Energy Technology Data Exchange (ETDEWEB)

Westgaard, T. [ed.

1996-02-01

The present report from the Royal Ministry of Industry and Energy deals with the Norwegian petroleum activity. Main topics are as follow: Historical overview; state organisation of petroleum activities; the economic impact of Norwegian oil and gas; state revenues; mainland activities; petroleum resources; production; marketing situation for petroleum products; environmental aspects; the legal and licence framework; licensing rounds; exploration; fields in production; fields under development; discoveries with development plan under consideration; transportation systems; licence interests; company interests. 36 refs., 24 figs., 15 tabs.

MULTIDISCIPLINARY PROJECTS FOR SECOND YEAR CHEMICAL AND MECHANICAL ENGINEERING STUDENTS

Directory of Open Access Journals (Sweden)

MARWAN M. SHAMEL

2013-04-01

Full Text Available In the second semester of the second year of a Mechanical Engineering course, students are supposed to take a Module Outside the Main Discipline (MOMD. This module is chosen to be “Product Design Exercise” a module that is offered to Chemical Engineering students at the same stage. The aim was to expose students from both disciplines to an environment in which they are encouraged to interact with and engage team members with a relatively different background. The students were divided into eight groups all comprised of Chemical and Mechanical Engineering students, and they were offered different open-ended projects that were selected to exploit the knowledge developed by the students thus far and they were slightly skewed towards Chemical Engineering. The students demonstrated a high level of cooperation and motivation throughout the period of the project. Effective communication and closing of knowledge gaps were prevalent. At the end of the project period, students produced a journal paper in lieu of the project report.

Gasoline Engine Mechanics. Performance Objectives. Intermediate Course.

Science.gov (United States)

Jones, Marion

Several intermediate performance objectives and corresponding criterion measures are listed for each of six terminal objectives presented in this curriculum guide for an intermediate gasoline engine mechanics course at the secondary level. (For the beginning course guide see CE 010 947.) The materials were developed for a two-semester (2 hour…

Aerosols emitted in underground mine air by diesel engine fueled with biodiesel.

Science.gov (United States)

Bugarski, Aleksandar D; Cauda, Emanuele G; Janisko, Samuel J; Hummer, Jon A; Patts, Larry D

2010-02-01

Using biodiesel in place of petroleum diesel is considered by several underground metal and nonmetal mine operators to be a viable strategy for reducing the exposure of miners to diesel particulate matter. This study was conducted in an underground experimental mine to evaluate the effects of soy methyl ester biodiesel on the concentrations and size distributions of diesel aerosols and nitric oxides in mine air. The objective was to compare the effects of neat and blended biodiesel fuels with those of ultralow sulfur petroleum diesel. The evaluation was performed using a mechanically controlled, naturally aspirated diesel engine equipped with a muffler and a diesel oxidation catalyst. The effects of biodiesel fuels on size distributions and number and total aerosol mass concentrations were found to be strongly dependent on engine operating conditions. When fueled with biodiesel fuels, the engine contributed less to elemental carbon concentrations for all engine operating modes and exhaust configurations. The substantial increases in number concentrations and fraction of organic carbon (OC) in total carbon over the baseline were observed when the engine was fueled with biodiesel fuels and operated at light-load operating conditions. Size distributions for all test conditions were found to be single modal and strongly affected by engine operating conditions, fuel type, and exhaust configuration. The peak and total number concentrations as well as median diameter decreased with an increase in the fraction of biodiesel in the fuels, particularly for high-load operating conditions. The effects of the diesel oxidation catalyst, commonly deployed to counteract the potential increase in OC emissions due to use of biodiesel, were found to vary depending upon fuel formulation and engine operating conditions. The catalyst was relatively effective in reducing aerosol number and mass concentrations, particularly at light-load conditions, but also showed the potential for an

Environmental impact of petroleum products in the soil. Part II: Petroleum products composition and key properties

International Nuclear Information System (INIS)

Zerlia, T.

2001-01-01

The fate of petroleum hydrocarbons in the soil depends on the chemical-physic properties of each hydrocarbon, as well as on the soil characteristics. The mean composition of various petroleum products, the key chemical compounds and their characteristics are focused in order to outline the environmental behaviour of petroleum hydrocarbons in the soil [it

21 CFR 172.888 - Synthetic petroleum wax.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Synthetic petroleum wax. 172.888 Section 172.888... CONSUMPTION Multipurpose Additives § 172.888 Synthetic petroleum wax. Synthetic petroleum wax may be safely used in or on foods in accordance with the following conditions: (a) Synthetic petroleum wax is a...

A study of competence in mathematics and mechanics in an engineering curriculum

Science.gov (United States)

Munns, Andrew

2017-11-01

Professional bodies expect engineers to show competence in both mathematics and engineering topics such as mechanics, using their abilities in both of these to solve problems. Yet within engineering programmes there is a phenomenon known as 'The Mathematics Problem', with students not demonstrating understanding of the subject. This paper will suggest that students are constructing different concept images in engineering and mathematics, based on their perception of either the use or exchange-value for the topics. Using a mixed methods approach, the paper compares 10 different types of concept image constructed by students, which suggests that familiar procedural images are preferred in mathematics. In contrast strategic and conceptual images develop for mechanics throughout the years of the programme, implying that different forms of competence are being constructed by students between the two subjects. The paper argues that this difference is attributed to the perceived use-value of mechanics in the career of the engineer, compared to the exchange-value associated with mathematics. Questions are raised about the relevance of current definitions of competence given that some routine mathematical operations previously performed by engineers are now being replaced by technology, in the new world of work.

Petroleum coke as energy source: an update

International Nuclear Information System (INIS)

Pinelli, G.

2008-01-01

A previous review presented a critical evaluation of the use of petroleum coke as energy source. After some years, with reference to increased petroleum coke production, that paper is revised. In particular, the attention is now focused on world petroleum coke market trends and, in regard to petroleum coke used as fuel, on new Italian environment laws. [it

Petroleum supply monthly with data from January 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum supply monthly with data for March 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration reflecting different levels of data timeliness and completeness. Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

Petroleum.

Science.gov (United States)

McManus, T. R.; And Others

1989-01-01

This review of petroleum covers: crude oil; fuels, gaseous and liquid; lubricants, oils, and greases; asphalts, bitumens, tars, and pitches; hydrocarbons; physical properties; metals in oil; nonmetallic elements and heterocompounds; and analytical methods and apparatus. (MVL)

Engineering of Impulse Mechanism for Mechanical Hander Power Tools

Science.gov (United States)

Nikolaevich Drozdov, Anatoliy

2018-03-01

The solution to the problem of human security in cities should be considered on the basis of an integrated and multidisciplinary approach, including issues of security and ecology in the application of technical means used to ensure the viability and development of technocracy. In this regard, an important task is the creation of a safe technique with improved environmental properties with high technological characteristics. This primarily relates to mechanised tool — the division of technological machines with built in engines is that their weight is fully or partially perceived by the operator’s hands, making the flow and control of the car. For this subclass of machines is characterized by certain features: a built-in motor, perception of at least part of their weight by the operator during the work, the implementation of feeding and management at the expense of the muscular power of the operator. Therefore, among the commonly accepted technical and economic characteristics, machines in this case, important ergonomic (ergonomics), regulation of levels which ensures the safety of the operator. To ergonomics include vibration, noise characteristics, mass, and force feeding machine operator. Vibration is a consequence of the dynamism of the system operator machine - processed object (environment) in which the engine energy is redistributed among all the structures, causing their instability. In the machine vibration caused by technological and constructive (transformative mechanisms) unbalance of individual parts of the drive, the presence of technological and design (impact mechanisms) clearances and other reasons. This article describes a new design of impulse mechanism for hander power tools (wrenches, screwdrivers) with enhanced torque. The article substantiates a simulation model of dynamic compression process in an operating chamber during impact, provides simulation results and outlines further lines of research.

Naval Petroleum and Oil Shale Reserves

International Nuclear Information System (INIS)

1992-01-01

During fiscal year 1992, the reserves generated $473 million in revenues, a $181 million decrease from the fiscal year 1991 revenues, primarily due to significant decreases in oil and natural gas prices. Total costs were $200 million, resulting in net cash flow of $273 million, compared with $454 million in fiscal year 1991. From 1976 through fiscal year 1992, the Naval Petroleum and Oil Shale Reserves generated more than $15 billion in revenues and a net operating income after costs of $12.5 billion. In fiscal year 1992, production at the Naval Petroleum Reserves at maximum efficient rates yielded 26 million barrels of crude oil, 119 billion cubic feet of natural gas, and 164 million gallons of natural gas liquids. From April to November 1992, senior managers from the Naval Petroleum and Oil Shale Reserves held a series of three workshops in Boulder, Colorado, in order to build a comprehensive Strategic Plan as required by Secretary of Energy Notice 25A-91. Other highlights are presented for the following: Naval Petroleum Reserve No. 1--production achievements, crude oil shipments to the strategic petroleum reserve, horizontal drilling, shallow oil zone gas injection project, environment and safety, and vanpool program; Naval Petroleum Reserve No. 2--new management and operating contractor and exploration drilling; Naval Petroleum Reserve No. 3--steamflood; Naval Oil Shale Reserves--protection program; and Tiger Team environmental assessment of the Naval Petroleum and Oil Shale Reserves in Colorado, Utah, and Wyoming

Effects of the petroleum tax reform

International Nuclear Information System (INIS)

Stensland, G.; Sunnevaag, K.; Tennfjord, B.S.

1992-04-01

The report evaluates the effects of the petroleum taxation in Norway. In connection with the general reform of the Norwegian industry taxation, changes are proposed in the petroleum tax law. The report gives a survey of the development in the Norwegian petroleum taxation, and analyses the effects of changing the tax revenue both for the Government and for the companies concerned. The effects of incentives caused by changing the taxation are looked upon. In the appendix the depreciation rules in connection with petroleum taxation are discussed. 18 refs., 17 figs

Kaner biodiesel production through hybrid reactor and its performance testing on a CI engine at different compression ratios

Directory of Open Access Journals (Sweden)

Ashok Kumar Yadav

2017-06-01

Full Text Available The present study deals with development of a hybrid reactor for biodiesel production based on the combined hydrodynamic cavitation and mechanical stirring processes. Biodiesel were produced using Kaner Seed Oil (KSO. The experimental results show that hybrid reactor produces 95% biodiesel yield within 45 min for 0.75% of catalyst and 6:1 M ratio which is significantly higher as compared to mechanical stirring or hydrodynamic cavitation alone. Thus biodiesel production process in hybrid reactor is cheap (high yield, efficient (time saving and environmentally friendly (lower% of catalyst. Performance study on engine shows that an increase in compression ratios (from 16 to 18 improves the engine performance using biodiesel blends as compared to petroleum diesel.

Research Advances of Microencapsulation and Its Prospects in the Petroleum Industry

Directory of Open Access Journals (Sweden)

Miaomiao Hu

2017-03-01

Full Text Available Additives in the petroleum industry have helped form an efficient system in the past few decades. Nowadays, the development of oil and gas has been facing more adverse conditions, and smart response microcapsules with the abilities of self-healing, and delayed and targeted release are introduced to eliminate obstacles for further exploration in the petroleum industry. However, limited information is available, only that of field measurement data, and not mechanism theory and structural innovation data. Thus we propose that the basic type, preparation, as well as mechanism of microcapsules partly depend on other mature fields. In this review, we explore the latest advancements in evaluating microcapsules, such as X-ray computed tomography (XCT, simulation, and modeling. Finally, some novel microencapsulated additives with unparalleled advantages, such as flexibility, efficiency, and energy-conservation are described.

The petroleum industry in 1999 (editorial)

International Nuclear Information System (INIS)

2001-01-01

This document deals with the petroleum activity in 1999. It provides three economic analysis. The first one concerns the petroleum industry activity in 1999 and the corresponding french energy policy. The second one presents the petroleum activity in the world. The third one presents the hydrocarbons market supplying in France. (A.L.B.)

International Joint Conference on Mechanics, Design Engineering & Advanced Manufacturing

CERN Document Server

Nigrelli, Vincenzo; Oliveri, Salvatore; Peris-Fajarnes, Guillermo; Rizzuti, Sergio

2017-01-01

This book gathers papers presented at the International Joint Conference on Mechanics, Design Engineering and Advanced Manufacturing (JCM 2016), held on 14-16 September, 2016, in Catania, Italy. It reports on cutting-edge topics in product design and manufacturing, such as industrial methods for integrated product and process design; innovative design; and computer-aided design. Further topics covered include virtual simulation and reverse engineering; additive manufacturing; product manufacturing; engineering methods in medicine and education; representation techniques; and nautical, aeronautics and aerospace design and modeling. The book is divided into eight main sections, reflecting the focus and primary themes of the conference. The contributions presented here will not only provide researchers, engineers and experts in a range of industrial engineering subfields with extensive information to support their daily work; they are also intended to stimulate new research directions, advanced applications of t...

Improvement of hydrodenitrogenation (HDN) in co-refining of coal-derived liquid and petroleum fraction

Energy Technology Data Exchange (ETDEWEB)

Machida, M.; Ono, S. [Idemitsu Kosan Co. Ltd., Tokyo (Japan); Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

1997-09-01

The improvement in hydrodenitrogenation (HDN) of coal-derived liquids by co-refining with a petroleum fraction results principally from lowering the nitrogen content of the feedstock (coal-derived liquid) by blending with a nitrogen-free petroleum fraction. Effects of different fractions of coal-derived liquids on HDN and hydrodeoxygenation (HDO) were also examined. The HDN improvement by co-refining could be interpreted in terms of Langmuir-Hinshelwood mechanism. 38 refs., 3 figs., 3 tabs.

Canadian retail petroleum markets study

International Nuclear Information System (INIS)

Ervin, M.J.

1998-02-01

A retail petroleum market study was conducted to provide a comprehensive overview of the competitiveness of the downstream petroleum industry in Canada and to set a foundation for effective policy development. The downstream petroleum industry, which includes the petroleum refining and marketing sectors, faces a poor public image, competitive pressures from U.S. and offshore refiners, and a broad range of environmental challenges. In this study, 19 markets representing a wide range of conditions were chosen for a detailed review of outlet economics. A market-by-market and regional comparisons of key competitiveness indicators was made in order to identify market and regional competitive differences as potential issues or opportunities within the industry. The study also included a pump price/margin model and provided a general overview of the retail gasoline sub-sector in terms of infrastructure. A review of prices, margins and demand patterns over the past several years was also undertaken to show the relationship between consumer demand patterns and pump price fluctuations. The study presented 22 findings which led to several conclusions and recommendations regarding the competitiveness of Canada's petroleum marketing sector. Two of the key conclusions were that taxation is a significant factor in the price of retail gasoline (about 50 per cent) and that government intervention into petroleum marketing is likely to be a poor alternative to market-based regulation. 18 tabs., 37 figs

A new guide of mechanical engineering

International Nuclear Information System (INIS)

1993-01-01

This book introduces a new guide of mechanical engineering which deals with basic thing such as mathematical formula, dynamics, material dynamics, industrial materials, machine design like screws and rivets, gears and springs, the method of machine such as drilling machine and its work, planar, shaper and slotter and their work, honing and super finishing machine and their work, measuring of machine, test and machine, hydraulics and hydraulic machine and telecommunication equipment and automation.

The para-petroleum industry

International Nuclear Information System (INIS)

2002-07-01

The para-petroleum industry includes societies that realize studies and installations for the deposits exploitation. This document presents the situation of the para-petroleum industry in 2001, the world investment growth of the activity, the french societies financial results and an inventory of the main operations in the amalgamation domain. (A.L.B.)

Environmental hazard and risk characterisation of petroleum substances: a guided "walking tour" of petroleum hydrocarbons.

Science.gov (United States)

Bierkens, Johan; Geerts, Lieve

2014-05-01

Petroleum substances are used in large quantities, primarily as fuels. They are complex mixtures whose major constituents are hydrocarbons derived from crude oil by distillation and fractionation. Determining the complete molecular composition of petroleum and its refined products is not feasible with current analytical techniques because of the huge number of molecular components. This complex nature of petroleum products, with their varied number of constituents, all of them exhibiting different fate and effect characteristics, merits a dedicated hazard and risk assessment approach. From a regulatory perspective they pose a great challenge in a number of REACH processes, in particular in the context of dossier and substance evaluation but also for priority setting activities. In order to facilitate the performance of hazard and risk assessment for petroleum substances the European oil company association, CONCAWE, has developed the PETROTOX and PETRORISK spreadsheet models. Since the exact composition of many petroleum products is not known, an underlying assumption of the PETROTOX and PETRORISK tools is that the behaviour and fate of a total petroleum substance can be simulated based on the physical-chemical properties of representative structures mapped to hydrocarbon blocks (HBs) and on the relative share of each HB in the total mass of the product. To assess how differing chemical compositions affect the simulated chemical fate and toxicity of hydrocarbon mixtures, a series of model simulations were run using an artificial petroleum substance, containing 386 (PETROTOX) or 160 (PETRORISK) HBs belonging to different chemical classes and molecular weight ranges, but with equal mass assigned to each of them. To this artificial petroleum substance a guided series of subsequent modifications in mass allocation to a delineated number of HBs belonging to different chemical classes and carbon ranges was performed, in what we perceived as a guided "walking tour

BIOREMEDIATION OF A PETROLEUM-HYDROCARBON

African Journals Online (AJOL)

ES OBE

under field conditions in the bioremediation of a petroleum- hydrocarbon polluted ... an accelerated biodegradation of petroleum hydrocarbons in a polluted agricultural soil ..... 12) Jackson, M.L. Soil chemical analysis. ... biological assay. 3 rd.

The 1999 MWV petroleum consumption forecast: Petroleum still in the lead in the German energy market

International Nuclear Information System (INIS)

Anon.

1999-01-01

Petroleum consumption in Germany has been stagnant over the last few years. Since in 1998 the decline in light heating oil sales was balanced out by an increase in fuel consumption and petroleum sales to the petrochemical industry, total domestic supplies of petroleum products amounted to 127.4 million tonnes and thus remained at last year's level. According to the latest forecast of the Mineraloelwirtschaftsverband e.V., extending to the year 2010, stagnation will continue for some years, but petroleum consumption is expected to then take a clear downward trend and fall off by 11 million tonnes (or 9%) until 2010. (orig./CB) [de

Petroleum marketing monthly, December 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-05

This publication provides information and statistical data on a variety of crude oils and refined petroleum products. It presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include domestic first purchase price, f.o.b. and landed cost of imported crude, and refiners` acquisition cost of crude. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane.

Isotope analysis in petroleum exploration

International Nuclear Information System (INIS)

Rodrigues, R.

1982-01-01

The study about isotopic analysis in petroleum exploration performed at Petrobras Research Center is showed. The results of the petroleum recuperation in same Brazilian basin and shelves are comented. (L.H.L.L.) [pt

Petroleum industry 1996; L`industrie petroliere 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector`s companies (oil groups, para-petroleum French industry, scientific and technical research)

Petroleum industry 1996; L`industrie petroliere 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector`s companies (oil groups, para-petroleum French industry, scientific and technical research)

Summary of Research 2001, Department of Mechanical Engineering, Graduate School of Engineering and Applied Sciences

National Research Council Canada - National Science Library

McNelley, Terry

2002-01-01

This report contains project summaries of the research projects in the Department of Mechanical Engineering A list of recent publications is also included, which consists of conference presentations...

Environment 2002. The Norwegian petroleum sector

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

The Ministry of Petroleum and Energy produces an annual environmental review in cooperation with the Norwegian Petroleum Directorate. The purpose of this publication is threefold: (1) to increase knowledge about the environmental aspects of Norwegian oil and gas activities, (2) to take a more detailed look at a specific topic which particularly concerns both the industry and the authorities, and identify the challenges and options faced, (3) to emphasise the governments goal of ensuring that Norway reconciles its role as a large energy producer with a pioneering position on environmental issues. This year's edition focuses on the topic of ''oil and fish - common sea''. Both the petroleum and fishing industries depend on the waters off Norway. Ever since petroleum activities began on the Norwegian continental shelf more than 30 years ago, the authorities have been keen to ensure that these two sectors can work in the same sea areas. What challenges and opportunities face the petroleum industry over discharges to the sea and living marine resources? How can the authorities ensure that this sector is able to coexist with the fisheries? These and similar questions about the relationship between the petroleum and fishing industries in their shared seas are covered in section two of this publication. Environment 2002 also incorporates a factual section, which covers the status of emissions/discharges, environmental impacts and measures to reduce discharges to the sea and emissions to the air from petroleum activities. The MPE hopes that a publication of this kind can enhance basic knowledge about petroleum activities and environmental issues.

Environment 2002. The Norwegian petroleum sector

International Nuclear Information System (INIS)

2002-01-01

The Ministry of Petroleum and Energy produces an annual environmental review in cooperation with the Norwegian Petroleum Directorate. The purpose of this publication is threefold: (1) to increase knowledge about the environmental aspects of Norwegian oil and gas activities, (2) to take a more detailed look at a specific topic which particularly concerns both the industry and the authorities, and identify the challenges and options faced, (3) to emphasise the governments goal of ensuring that Norway reconciles its role as a large energy producer with a pioneering position on environmental issues. This year's edition focuses on the topic of ''oil and fish - common sea''. Both the petroleum and fishing industries depend on the waters off Norway. Ever since petroleum activities began on the Norwegian continental shelf more than 30 years ago, the authorities have been keen to ensure that these two sectors can work in the same sea areas. What challenges and opportunities face the petroleum industry over discharges to the sea and living marine resources? How can the authorities ensure that this sector is able to coexist with the fisheries? These and similar questions about the relationship between the petroleum and fishing industries in their shared seas are covered in section two of this publication. Environment 2002 also incorporates a factual section, which covers the status of emissions/discharges, environmental impacts and measures to reduce discharges to the sea and emissions to the air from petroleum activities. The MPE hopes that a publication of this kind can enhance basic knowledge about petroleum activities and environmental issues

Environmental pollution by petroleum

Energy Technology Data Exchange (ETDEWEB)

Murata, T

1974-06-01

Pollution causes, cases, and remedies at various stages of petroleum production and usage are reviewed. Petroleum extraction (off-shore drilling and Arctic drilling) can be accompanied by mishaps. In 1971, IMCO (an international safety committee) proposed the partitioning of oil tanker holds into smaller compartments to minimize spillage in case of disaster. Although the solubility of oil in waste water from refineries is reckoned by ppM, the total amount dissolved is not negligible. Petroleum storage and transport on land is complicated by problems of safety in terms of population density as well as by pollution problems. Petroleum end-products such as plastic trash and automobile exhausts contribute to pollution. The role of aldehydes and peroxides in photochemical smog formation must be investigated further. Proper treatment of pollution at each specific point of occurrence, rather than at the end of a production line is recommended. Pollutant concentration for treatment, rather than pollutant dilution for dispersal, should be considered. Technology for pollution abatement is available, but not always economically feasible.

Analysis of petroleum oily sludge producing in petroleum field of Rio Grande do Norte, Brazil

Energy Technology Data Exchange (ETDEWEB)

Lima, Cicero de Souza; Lima, Regineide Oliveira; Silva, Edjane Fabiula Buriti da; Castro, Kesia Kelly Vieira de; Chiavone Filho, Osvaldo; Araujo, Antonio Souza de [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil)

2012-07-01

In exploration and production of petroleum is generated solid waste different and components other. The petroleum oily sludge is a complex mix of components different (water, oil and solid). The petroleum oily sludge generally has other residues and is formed during production and operations, transport, storage and petroleum refining (atmospheric residue, vacuum residue and catalytic cracking residue). However, according to its origin, the compositions can be found quite varied for sludge. Observing the process steps production and refining is possible to locate its main sources and percentage contributions in terms of waste generation. The elemental analysis was performed with oily sludge from region and it showed different composition. For carbon element and hydrogen, small differences was observed, but for was observed greater differences for Oxygen element. The sludge has different inorganic and organic composition. The sludge from oil water separator (OWS) 2 showed a greater amount of oil (94.88%), this may indicate a residue of aggregate high for petroleum industry. In analysis of Saturates, Aromatics, Resins and Asphaltenes (SARA), the sludge from unloading showed amount high of saturates. The inorganic material separated from sludge was characterized and sludge from OWS 2 had high amount sulfur (41.57%). The sludge analyzed showed organic components high values, so it can be treated and reprocessed in process units petroleum industry. The analysis thermal degradation had a better setting for treated oily sludge. (author)

The business of petroleum exploration

International Nuclear Information System (INIS)

Steinmetz, R.

1992-01-01

This book contains the proceedings of the Business of Petroleum Exploration. The following topics are included: Petroleum business; Economic aspects of the business; Managing business; and Legal, Political, Ethical and environment aspects of the business

Petroleum supply annual, 1997. Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 48 tabs.

Petroleum supply annual 1992: Volume 1

International Nuclear Information System (INIS)

1993-01-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1992 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1992, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them

Petroleum supply annual, 1997. Volume 1

International Nuclear Information System (INIS)

1998-06-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1997 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains three sections: Summary Statistics, Detailed Statistics, and Refinery Statistics; each with final annual data. The second volume contains final statistics for each month of 1997, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. 16 figs., 48 tabs

Lasers and petroleum in Venezuela

Energy Technology Data Exchange (ETDEWEB)

da Costa, G.; Guerri, G.; Calatroni, J. (Universidad Simon Bolivar, Caracas (Venezuela). Lab. de Optica Cuantica)

1978-06-01

The viscosity of heavy hydrocarbons is one reason why conventional drilling methods are insufficient for petroleum extraction in Venezuela at a depth of 1000 m. The Quantum Optics Laboratory of Simon Bolivar University in Caracas is conducting a search for novel perforation and heating tools for petroleum extraction. Basic research is being carried out using a 10 MW TEA-CO/sub 2/ laser. The laser is not only a research tool but a matter of national interests, as petroleum is Venezuela's main export article.

Petroleum marketing monthly with data for January 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

This publication provides information and statistical data on a variety of crude oils and refined petroleum products. Statistics on crude oil costs and refined petroleum products sales are presented. Data on crude oil include the domestic purchase price, the free on board and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oils and sales of petroleum products are presented in five sections: (1) summary statistics, (2) crude oil prices, (3) prices of petroleum products, (4) volumes of petroleum products, and (5) prime supplier sales volumes of petroleum products for local consumption. 50 tabs.

Engineering a Place for Women: A Study of How Departmental Climate Influences the Career Satisfaction of Female Mechanical Engineering Faculty Members

Science.gov (United States)

Young, Monica J.

2012-01-01

The purpose of this mixed-methods study was to better understand how female mechanical engineering faculty members' career experiences in academia affect their satisfaction. Specifically, the research considered differences in satisfaction reported by female and male mechanical engineering faculty members in terms of: (a) departmental…

Petroleum Resins: Separation, Character, and Role in Petroleum

DEFF Research Database (Denmark)

Andersen, Simon Ivar; Speight, James

2001-01-01

are precipitated, adsorbents are added to the n-pentane solutions of the resins and oils, by which process the resins are adsorbed and subsequently recovered by the use of a more polar solvent, and the oils remain in solution. The resin fraction plays an important role in the stability of petroleum and prevents...... separation of the asphaltene constituents as a separate phase. Indeed, the absence of the resin fraction (produced by a variety of methods) from the maltenes influences the ability of the de-resined maltenes to accommodate the asphaltenes either in solution or as a stable part of a colloidal system. In spite....... Suggestions are also made regarding current thoughts of the role of these constituents on the structure and stability of petroleum....

Healthcare Technology Management (HTM) of mechanical ventilators by clinical engineers

OpenAIRE

Yoshioka, Jun; Nakane, Masaki; Kawamae, Kaneyuki

2014-01-01

Mechanical ventilator failures expose patients to unacceptable risks, and maintaining mechanical ventilator safety is an important issue. We examined the usefulness of maintaining mechanical ventilators by clinical engineers (CEs) using a specialized calibrator. These evaluations and the ability to make in-house repairs proved useful for obviating the need to rent ventilators which, in turn, might prove faulty themselves. The CEs' involvement in maintaining mechanical ventilators is desirable...

A Study of Competence in Mathematics and Mechanics in an Engineering Curriculum

Science.gov (United States)

Munns, Andrew

2017-01-01

Professional bodies expect engineers to show competence in both mathematics and engineering topics such as mechanics, using their abilities in both of these to solve problems. Yet within engineering programmes there is a phenomenon known as "The Mathematics Problem", with students not demonstrating understanding of the subject. This…

Computational Quantum Mechanics for Materials Engineers The EMTO Method and Applications

CERN Document Server

Vitos, L

2007-01-01

Traditionally, new materials have been developed by empirically correlating their chemical composition, and the manufacturing processes used to form them, with their properties. Until recently, metallurgists have not used quantum theory for practical purposes. However, the development of modern density functional methods means that today, computational quantum mechanics can help engineers to identify and develop novel materials. Computational Quantum Mechanics for Materials Engineers describes new approaches to the modelling of disordered alloys that combine the most efficient quantum-level th

Estimating thermal maturity in the Eagle Ford Shale petroleum system using gas gravity data

Science.gov (United States)

Birdwell, Justin E.; Kinney, Scott A.

2017-01-01

Basin-wide datasets that provide information on the geochemical properties of petroleum systems, such as source rock quality, product composition, and thermal maturity, are often difficult to come by or assemble from publically available data. When published studies are available and include these kinds of properties, they generally have few sampling locations and limited numbers and types of analyses. Therefore, production-related data and engineering parameters can provide useful proxies for geochemical properties that are often widely available across a play and in some states are reported in publically available or commercial databases. Gas-oil ratios (GOR) can be calculated from instantaneous or cumulative production data and can be related to the source rock geochemical properties like kerogen type (Lewan and Henry, 1999) and thermal maturity (Tian et al., 2013; U.S. Energy Information Administration [EIA], 2014). Oil density or specific gravity (SG), often reported in American Petroleum Institute units (°API = 141.5 /SG – 131.5), can also provide information on source rock thermal maturity, particularly when combined with GOR values in unconventional petroleum systems (Nesheim, 2017).

The petroleum taxation in France

International Nuclear Information System (INIS)

2005-09-01

This document details the french specificities of taxation concerning the petroleum products: the TIPP. It shows how this policy acts upon the petroleum products consumption behavior and how it allows the financing of the decentralization. (A.L.B.)

The United States facing their petroleum dependence

International Nuclear Information System (INIS)

Noel, P.

2002-06-01

In the framework of ''the energy crisis of 2000-2001'', the Cheney report and the petroleum dependence, this study presents a critical examination of the United States petroleum situation, its perception in the american political milieu and the public policies implementing during the last ten years. The first section is devoted to the petroleum supply. In the second section, the american petroleum policy and the energy safety are studied. (A.L.B.)

Petroleum marketing monthly, November 1993

Energy Technology Data Exchange (ETDEWEB)

1993-11-09

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed costs of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, July 1993

Energy Technology Data Exchange (ETDEWEB)

1993-07-15

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, January 1994

Energy Technology Data Exchange (ETDEWEB)

1994-02-01

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, February 1994

Energy Technology Data Exchange (ETDEWEB)

1994-02-25

The Petroleum Marketing Monthly is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, August 1993

Energy Technology Data Exchange (ETDEWEB)

1993-08-10

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, April 1994

Energy Technology Data Exchange (ETDEWEB)

1994-04-12

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, March 1994

Energy Technology Data Exchange (ETDEWEB)

1994-03-22

The Petroleum Marketing Monthly is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, education institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiner`s acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented.

Petroleum marketing monthly, October 1993

Energy Technology Data Exchange (ETDEWEB)

1993-10-07

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase prices, the f.o b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates residuals, aviation fuels, kerosene, and propane are presented.

Simulation based engineering in solid mechanics

CERN Document Server

Rao, J S

2017-01-01

This book begins with a brief historical perspective of the advent of rotating machinery in 20th century Solid Mechanics and the development of the discipline of the Strength of Materials. High Performance Computing (HPC) and Simulation Based Engineering Science (SBES) have gradually replaced the conventional approach in Design bringing science directly into engineering without approximations. A recap of the required mathematical principles is given. The science of deformation, strain and stress at a point under the application of external traction loads is next presented. Only one-dimensional structures classified as Bars (axial loads), Rods (twisting loads) and Beams (bending loads) are considered in this book. The principal stresses and strains and von Mises stress and strain that used in design of structures are next presented. Lagrangian solution was used to derive the governing differential equations consistent with assumed deformation field and solution for deformations, strains and stresses were obtai...

PREFACE: 1st International Conference on Mechanical Engineering Research 2011 (ICMER2011)

Science.gov (United States)

Abu Bakar, Rosli

2012-09-01

The year 2010 represented a significant milestone in the history of the Mechanical Engineering community with the organization of the first and second national level conferences (National Conference in Mechanical Engineering for Research, 1st and 2nd NCMER) at Universiti Malaysia Pahang on 26-27 May and 3-4 December 2010. The conferences attracted a large number of delegates from different premier academic and research institutions in the country to participate and share their research experiences at the conference. The International Conference on Mechanical Engineering Research (ICMER 2011) followed on from the first and second conferences due to good support from researchers. The ICMER 2011 is a good platform for researchers and postgraduate students to present their latest finding in research. The conference covers a wide range of topics including the internal combustion engine, machining processes, heat and mass transfer, fuel, biomechanical analysis, aerodynamic analysis, thermal comfort, computational techniques, design and simulation, automotive transmission, optimization techniques, hybrid electric vehicles, engine vibration, heat exchangers, finite element analysis, computational fluid dynamics, green energy, vehicle dynamics renewable energy, combustion, design, product development, advanced experimentation techniques, to name but a few. The international conference has helped to bridge the gap between researchers working at different institutions and in different countries to share their knowledge and has helped to motivate young scientists with their research. This has also given some clear direction for further research from the deliberations of the conference. Several people have contributed in different ways to the success of the conference. We thank the keynote speakers and all authors of the contributed papers, for the cooperation rendered to us in the publication of the CD conference proceedings. In particular, we would like to place on record our

Neutron activation analysis for the determination of arsenic and mercury in petroleum and petroleum distillates

International Nuclear Information System (INIS)

Resnizky, Sara M.

1999-01-01

A radiochemical separation procedure to determine As and Hg in petroleum and petroleum distillates is described. The procedure uses the formation of HgS to co-precipitate the As and Hg activities produced during the irradiation. (author)

The Engineering Mechanism in Formation of Informational Basis of Analysis of Financial Sustainability of Enterprise

Directory of Open Access Journals (Sweden)

Chumak Oksana V.

2017-12-01

Full Text Available The article is aimed at substantiating the mechanism and instruments of financial and accountancy engineering with purpose of formation of information support of analysis of financial sustainability in the enterprise management system. The essence and preconditions of introduction of financial and accountancy engineering are disclosed. Expediency of application of the financial engineering mechanism at enterprise while analyzing financial sustainability has been substantiated. An analysis of methods of formation and use of derivative balance reports was carried out. Models of the conception of mechanisms and instruments of financial and accountancy engineering in analyzing the financial sustainability of enterprise have been suggested. A mega-accounts system in the working plan of the enterprise’s accounts has been recommended. Seven iterations have been provided, which constitute the basis of accounting-analytical support of the accountancy engineering. The information obtained on the basis of the financial and accountancy engineering mechanism allows to carry out real assessment of the enterprise’s financial sustainability.

Petroleum and geopolitics; Petrole et geopolitique

Energy Technology Data Exchange (ETDEWEB)

Chaigneau, P. [Centre d' etudes diplomatiques et strategiques de Paris, 75 (France)

2004-04-01

Todays, petroleum companies consider that despite the constant increase of petroleum consumption, petroleum will remain the main energy source for at least 40 years. However, after the Iraq conflict, new regional situations are changing. China, for instance, with its growing up demand, will change the physiognomy of the oil market. In parallel, from Indonesia to Africa, petroleum and religion interfere and explain the new conflict areas. As for the US strategy, which is not limited to the energy paradigm, it largely integrates energy in the main lines of its diplomacy, from the 'Wide Middle East' to the 'Sahel initiative', and in its position with respect to Venezuela.

Propulsion Mechanism of Catalytic Microjet Engines.

Science.gov (United States)

Fomin, Vladimir M; Hippler, Markus; Magdanz, Veronika; Soler, Lluís; Sanchez, Samuel; Schmidt, Oliver G

2014-02-01

We describe the propulsion mechanism of the catalytic microjet engines that are fabricated using rolled-up nanotech. Microjets have recently shown numerous potential applications in nanorobotics but currently there is a lack of an accurate theoretical model that describes the origin of the motion as well as the mechanism of self-propulsion. The geometric asymmetry of a tubular microjet leads to the development of a capillary force, which tends to propel a bubble toward the larger opening of the tube. Because of this motion in an asymmetric tube, there emerges a momentum transfer to the fluid. In order to compensate this momentum transfer, a jet force acting on the tube occurs. This force, which is counterbalanced by the linear drag force, enables tube velocities of the order of 100 μ m/s. This mechanism provides a fundamental explanation for the development of driving forces that are acting on bubbles in tubular microjets.

The Application of Problem-Based Learning in Mechanical Engineering

Science.gov (United States)

Putra, Z. A.; Dewi, M.

2018-02-01

The course of Technology and Material Testing prepare students with the ability to do a variety of material testing in the study of mechanical engineering. Students find it difficult to understand the materials to make them unable to carry out the material testing in accordance with the purpose of study. This happens because they knowledge is not adequately supported by the competence to find and construct learning experience. In this study, quasy experiment research method with pre-post-test with control group design was used. The subjects of the study were students divided in two groups; control and experiment with twenty-two students in each group. Study result: their grades showed no difference in between the pre-test or post-test in control group, but the difference in grade existed between the pre-test and post-test in experiment group. Yet, there is no significant difference in the study result on both groups. The researcher recommend that it is necessary to develop Problem-Based Learning that suits need analysis on D3 Program for Mechanical Engineering Department at the State University of Padang, to ensure the compatibility between Model of Study and problems and need. This study aims to analyze how Problem-Based Learning effects on the course of Technology and Material Testing for the students of D3 Program of Mechanical Engineering of the State University of Padang.

Petroleum product scarcity: a review of the supply and distribution of petroleum products in Nigeria

International Nuclear Information System (INIS)

Akpoghomeh, Osi S.; Badejo, Dele

2006-01-01

Nigeria ranks high among the comity of oil producers both at the world level and among the OPEC eleven. It is, therefore, paradoxical that the supply of all petroleum products is erratic and has declined sharply in the recent past. This paper thus reviews the petroleum product supply and distribution systems in the country to ascertain the extent to which the system may have contributed to the present product scarcity in Nigeria and, by extension, identify the causes of the present regime of petroleum product scarcity. The paper observes that the network density and connectivity of petroleum product distribution pipelines are low and both indicators consequently show the inadequacy/deficiency of the network in ensuring an efficient distribution system. The supply mode, on the other hand, has, over the years, demonstrated its inability to guarantee adequate supply due to factors including sabotage, vandalism, banditry and poorly maintained infrastructure. Further, the federal government and the major and independent marketers could not sustain the importation of petroleum products because of the shortfall between the landed cost of imported products and their selling prices in Nigeria, which made the business unprofitable. Finally, the paper examines the withdrawal by the federal government of subsidies on the price of petroleum products consumed locally. All the above factors together occasioned increases in the cost of products. In conclusion, this paper supports the call for the privatization of refineries and the depot/pipeline system as a viable option to end the supply problems. (Author)

Game mechanics engine

OpenAIRE

Magnusson, Lars V

2011-01-01

Game logic and game rules exists in all computer games, but they are created di erently for all game engines. This game engine dependency exists because of how the internal object model is implemented in the engine, as a place where game logic data is intermingled with the data needed by the low- level subsystems. This thesis propose a game object model design, based on existing theory, that removes this dependency and establish a general game logic framework. The thesis the...

Environmental Impacts of Petroleum Production: Initial Results from the Osage-Skiatook Petroleum Environmental Research Sites, Osage County, Oklahoma

Science.gov (United States)

Kharaka, Yousif K.; Otton, James K.

2003-01-01

Exploration for and production of petroleum have caused major detrimental impacts to soils, surface and ground waters, and the local ecosystems in the United States. These impacts arise primarily from the improper disposal of large volumes of saline water produced with oil and gas, from accidental hydrocarbon and produced water releases, and from abandoned oil wells that were not correctly sealed. It is important to understand the long-term and short-term effects of produced water and hydrocarbon releases from these sites in order to develop risk-based remediation plans. Remediation is particularly needed in aging and depleted fields where land use is changing from petroleum production to residential, agricultural or recreational uses. About 20 scientists from the USGS and other governmental agencies and academia are involved in a multidisciplinary investigation to study the transport, fate, and natural attenuation of inorganic salts, trace metals, organic compounds and radionuclides present in produced water, and their impacts at the Osage-Skiatook Petroleum Environmental Research (OSPER) 'A' and 'B' sites, located on the Osage Reservation in Osage County, Oklahoma. Stakeholders in the project include the Osage Nation, which holds the mineral rights, the Bureau of Indian Affairs with trust responsibility, and the Army Corps of Engineers, which owns the surface rights at these sites and manages adjacent Skiatook Lake. The 4250-hectare Skiatook Lake provides drinking water to local Tulsa suburban communities and a rural water district, and offers recreational fishing and boating opportunities to tens of thousands of visitors each year. Approximately 1.5 and 1.0 hectare of land at the OSPER 'A' (depleted Lester lease) and 'B' (active Branstetter lease) sites, respectively, are affected by salt scarring, tree kills, soil salinization and brine and petroleum contamination due to the leakage of produced water and associated hydrocarbons from brine pits and accidental

Healthcare Technology Management (HTM) of mechanical ventilators by clinical engineers.

Science.gov (United States)

Yoshioka, Jun; Nakane, Masaki; Kawamae, Kaneyuki

2014-01-01

Mechanical ventilator failures expose patients to unacceptable risks, and maintaining mechanical ventilator safety is an important issue. We examined the usefulness of maintaining mechanical ventilators by clinical engineers (CEs) using a specialized calibrator. These evaluations and the ability to make in-house repairs proved useful for obviating the need to rent ventilators which, in turn, might prove faulty themselves. The CEs' involvement in maintaining mechanical ventilators is desirable, ensures prompt service, and, most importantly, enhances safe management of mechanical ventilators.

comparison of elastic-plastic FE method and engineering method for RPV fracture mechanics analysis

International Nuclear Information System (INIS)

Sun Yingxue; Zheng Bin; Zhang Fenggang

2009-01-01

This paper described the FE analysis of elastic-plastic fracture mechanics for a crack in RPV belt line using ABAQUS code. It calculated and evaluated the stress intensity factor and J integral of crack under PTS transients. The result is also compared with that by engineering analysis method. It shows that the results using engineering analysis method is a little larger than the results using FE analysis of 3D elastic-plastic fracture mechanics, thus the engineering analysis method is conservative than the elastic-plastic fracture mechanics method. (authors)

Tailpipe emissions and engine performance of a light-duty diesel engine operating on petro- and bio-diesel fuel blends.

Science.gov (United States)

2014-06-01

This report summarizes the experimental apparatus developed in the Transportation Air Quality Laboratory (TAQ Lab) at the University of Vermont to compare light-duty diesel engine performance and exhaust emissions when operating on petroleum diesel (...

Bioremediation of petroleum-contaminated soil: A Review

Science.gov (United States)

Yuniati, M. D.

2018-02-01

Petroleum is the major source of energy for various industries and daily life. Releasing petroleum into the environment whether accidentally or due to human activities is a main cause of soil pollution. Soil contaminated with petroleum has a serious hazard to human health and causes environmental problems as well. Petroleum pollutants, mainly hydrocarbon, are classified as priority pollutants. The application of microorganisms or microbial processes to remove or degrade contaminants from soil is called bioremediation. This microbiological decontamination is claimed to be an efficient, economic and versatile alternative to physicochemical treatment. This article presents an overview about bioremediation of petroleum-contaminated soil. It also includes an explanation about the types of bioremediation technologies as well as the processes.

Use of Water-Fuel Mixture in Diesel Engines at Fishing Vessels

Science.gov (United States)

Klyus, Oleg; Bezyukov, O.

2017-06-01

The paper presents the laboratory test results determining physical parameters of fuel mixture made up of petroleum diesel oil, rapeseed oil methyl esters (up to 20%) and water (up to 2.5%). The obtained parameters prove that adding bio-components (rapeseed oil methyl esters) and water to fuel does not result in deterioration of their physical and chemical properties and are comparable to base fuel parameters, namely petroleum diesel oil. The mixture was a subject of bench testing with the use of a self-ignition engine by means of pre-catalytic fuel treatment. The treatment process consisted in fuel - catalytically active material direct contact on the atomizer body. At the comparable operational parameters for the engine, the obtained exhaust gases opacity was lower up to 60% due to the preliminary fuel mixture treatment in relation to the factory-made fuel injection system using petroleum diesel oil.

USE OF WATER-FUEL MIXTURE IN DIESEL ENGINES AT FISHING VESSELS

Directory of Open Access Journals (Sweden)

Oleg KLYUS

2017-04-01

Full Text Available The paper presents the laboratory test results determining physical parameters of fuel mixture made up of petroleum diesel oil, rapeseed oil methyl esters (up to 20% and water (up to 2.5%. The obtained parameters prove that adding bio-components (rapeseed oil methyl esters and water to fuel does not result in deterioration of their physical and chemical properties and are comparable to base fuel parameters, namely petroleum diesel oil. The mixture was a subject of bench testing with the use of a self-ignition engine by means of pre-catalytic fuel treatment. The treatment process consisted in fuel – catalytically active material direct contact on the atomizer body. At the comparable operational parameters for the engine, the obtained exhaust gases opacity was lower up to 60% due to the preliminary fuel mixture treatment in relation to the factory-made fuel injection system using petroleum diesel oil.

NASA GSFC Mechanical Engineering Latest Inputs for Verification Standards (GEVS) Updates

Science.gov (United States)

Kaufman, Daniel

2003-01-01

This viewgraph presentation provides information on quality control standards in mechanical engineering. The presentation addresses safety, structural loads, nonmetallic composite structural elements, bonded structural joints, externally induced shock, random vibration, acoustic tests, and mechanical function.

The use of nuclear energy for obtaining petroleum

International Nuclear Information System (INIS)

Waldmann, H.; Koch, C.; Thelen, H.J.; Kappe, P.

1982-01-01

After some basic considerations of petroleum demand, petroleum supply and petroleum reserves, the article gives a survey of the various methods of obtaining petroleum. The use of energy in the form of steam and electricity in the previously used processes and in conventional deposits requires up to 50% of the energy contained in the oil obtained. Now unconventional sources of petroleum (tertiary petroleum, heavy fractions and shale oil) could become of interest to West Germany in the near future. The economy of production can be determined by the energy source used, to a large extent. A series of possibilities are discussed for using nuclear steam raising systems for this purpose. (UA) [de

Petroleum marketing monthly with data for May 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly with data for September 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures and accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Elements of Motivational Structure for Studying Mechanical Engineering

Science.gov (United States)

Dubreta, Nikša; Miloš, Damir

2017-01-01

The article presents the findings on students' reasons for studying mechanical engineering. These reasons were covered in terms of extrinsic and intrinsic motivation additionally related to selected independent variables of the sample--students' secondary school Grade Point Average, their gender and the socio-economic status. The research was…

A comparative study of the rheological and sensory properties of a petroleum-free and a petroleum-based cosmetic cream.

Science.gov (United States)

Wang, Fan C; Marangoni, Alejandro G

A petroleum-free skin cream was developed using food-grade ingredients. The rheological and sensorial properties of this petroleum-free skin cream were compared to a commercially available petroleum-based skin cream. Specifically, large-amplitude oscillatory shear (LAOS) characterization of the two skin creams was performed. The petroleum-free skin cream showed similar linear and nonlinear viscoelastic rheological properties, comparable skin hydration functions, and consumer acceptance as the commercially available skin cream. A schematic diagram aiming to correlate the physical and sensorial properties of skin cream was also proposed at the end of the work. Results of this work could provide the cosmetic industry necessary information for the development of alternatives for petroleum-based skin creams.

Essays on the history of mechanical engineering

CERN Document Server

Genchi, Giuseppe

2016-01-01

This book treats several subjects from the History of Mechanism and Machine Science, and also contains an illustrative presentation of the Museum of Engines and Mechanisms of the University of Palermo, Italy, which houses a collection of various pieces of machinery from the last 150 years. The various sections deal with some eminent scientists of the past, with the history of industrial installations, machinery and transport, with the human inventiveness for mechanical and scientific devices, and with robots and human-driven automata. All chapters have been written by experts in their fields. The volume shows a wide-ranging panorama on the historical progress of scientific and technical knowledge in the past centuries. It will stimulate new research and ideas for those involved in the history of Science and Technology.

Petroleum supply monthly with data for September 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

Data presented in this document describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. This document contains information on oil production, imports, exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). When aggregated, the data reported by the various petroleum sectors in this report approximately represent the consumption of petroleum products in the U.S.

Petroleum supply annual 1994. Volume 1

International Nuclear Information System (INIS)

1995-01-01

The Petroleum Supply Annual (PSA) contains information on the supply and disposition of crude oil and petroleum products. The publication reflects data that were collected from the petroleum industry during 1994 through annual and monthly surveys. The PSA is divided into two volumes. This first volume contains four sections: Summary Statistics, Detailed Statistics, Refinery Capacity, and Oxygenate Capacity each with final annual data. The second volume contains final statistics for each month of 1994, and replaces data previously published in the Petroleum Supply Monthly (PSM). The tables in Volumes 1 and 2 are similarly numbered to facilitate comparison between them. Below is a description of each section in Volume 1 of the PSA

Stirling engine control mechanism and method

Science.gov (United States)

Dineen, John J.

1983-01-01

A reciprocating-to-rotating motion conversion and power control device for a Stirling engine includes a hub mounted on an offset portion of the output shaft for rotation relative to the shaft and for sliding motion therealong which causes the hub to tilt relative to the axis of rotation of the shaft. This changes the angle of inclination of the hub relative to the shaft axis and changes the axial stroke of a set of arms connected to the hub and nutating therewith. A hydraulic actuating mechanism is connected to the hub for moving its axial position along the shaft. A balancing wheel is linked to the hub and changes its angle of inclination as the angle of inclination of the hub changes to maintain the mechanism in perfect balance throughout its range of motion.

Taxation of petroleum products: theory and empirical evidence

International Nuclear Information System (INIS)

Gupta, S.; Mahler, W.

1995-01-01

The domestic taxation of petroleum products is an important source of revenue in most countries. However, there is a wide variation of tax rates on petroleum products across countries, which cannot be explained by economic theory alone. This paper surveys different considerations advanced for taxing petroleum and presents petroleum tax rate data in 120countries. (author)

Petroleum marketing monthly, August 1990

Energy Technology Data Exchange (ETDEWEB)

1990-11-07

The Petroleum Marketing Monthly (PMM) is designed to give information and statistical data about a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. 12 figs., 49 tabs.

Rare earth oxide reinforced Al{sub 2}O{sub 3}-TiO{sub 2} ceramics for inert coating of metallic parts for petroleum extraction

Energy Technology Data Exchange (ETDEWEB)

Yadava, Yoggendra Prasad; Rego, Sheila Alves Bezerra da Costa; Ferreira, Ricardo Artur Sanguinetti [Universidade Federal de Pernambuco (UFPE), Recife (Brazil)

2012-07-01

Recent findings of largest known pre-salt petroleum reservoir in Brazil have created an intense demand for new materials capable of withstanding direct contact with the crude petroleum as it is a highly corrosive and chemically reactive fluid. Petroleum drilling equipment, storage tanks and transportation systems suffer from constant physical stress caused by chemical attack of crude petroleum on its structure. Ceramics are materials with high chemical stability in hostile environment and therefore can be used as an inert coating material to resolve such problems. To date, ceramics based on alumina are most widely used in practice where there is demand for high mechanical strength and high fracture toughness. However intrinsic fragility of ceramics is still a fatal factor for their use in mechanical structures. To improve these characteristics, usually ceramics are reinforced with one or more ceramic additives. Mechanical properties of alumina based ceramics improve considerably with the addition of TiO{sub 2}, TiN, ZrO{sub 2} etc. ceramic additives. Nucleation and propagation of cracks is a major problem for ceramic coating applications. Initial studies show that addition of small percentages of rare earth oxides can increase the toughness of the alumina based ceramics. In the present work, we have produced rare-earth oxide (CeO{sub 2}) reinforced Al{sub 2}O{sub 3}-TiO{sub 2} ceramics in proportions of 5-20 wt% TiO{sub 2} and 2%wt% CeO{sub 2} through thermomechanical processing and sintering techniques and studied there microstructural characteristics and mechanical properties. To evaluate the potential of these ceramics as inert coatings for crude petroleum extraction, storage and transportation systems, we have studied the physic-chemical and mechanical stability of these ceramics in crude petroleum environment. Our studies presented satisfactory results in terms of physic-chemical and mechanical stability of these materials for the use of 2wt% of CeO{sub 2