Bioremediation of Petroleum Hydrocarbon Contaminated Sites

Energy Technology Data Exchange (ETDEWEB)

Fallgren, Paul

2009-03-30

Bioremediation has been widely applied in the restoration of petroleum hydrocarbon-contaminated. Parameters that may affect the rate and efficiency of biodegradation include temperature, moisture, salinity, nutrient availability, microbial species, and type and concentration of contaminants. Other factors can also affect the success of the bioremediation treatment of contaminants, such as climatic conditions, soil type, soil permeability, contaminant distribution and concentration, and drainage. Western Research Institute in conjunction with TechLink Environmental, Inc. and the U.S. Department of Energy conducted laboratory studies to evaluate major parameters that contribute to the bioremediation of petroleum-contaminated drill cuttings using land farming and to develop a biotreatment cell to expedite biodegradation of hydrocarbons. Physical characteristics such as soil texture, hydraulic conductivity, and water retention were determined for the petroleum hydrocarbon contaminated soil. Soil texture was determined to be loamy sand to sand, and high hydraulic conductivity and low water retention was observed. Temperature appeared to have the greatest influence on biodegradation rates where high temperatures (>50 C) favored biodegradation. High nitrogen content in the form of ammonium enhanced biodegradation as well did the presence of water near field water holding capacity. Urea was not a good source of nitrogen and has detrimental effects for bioremediation for this site soil. Artificial sea water had little effect on biodegradation rates, but biodegradation rates decreased after increasing the concentrations of salts. Biotreatment cell (biocell) tests demonstrated hydrocarbon biodegradation can be enhanced substantially when utilizing a leachate recirculation design where a 72% reduction of hydrocarbon concentration was observed with a 72-h period at a treatment temperature of 50 C. Overall, this study demonstrates the investigation of the effects of

Risk analysis associated with petroleum hydrocarbons: is everything running smoothly?

International Nuclear Information System (INIS)

Morin, D.

1999-01-01

Petroleum products represent one of the main sources of environmental contamination, and these products are complex, composed of several hundred individual hydrocarbons. The evaluation of the risks associated with petroleum products is often limited by certain specific parameters such as benzene. The petroleum hydrocarbons running from C(10) to C(50) are not often integrated in an analysis of the toxological risks since the toxological characterization of a complex mixture of hydrocarbons is difficult to carry out. There exist in the United States two approaches that were developed recently that allow the integration of various hydrocarbons comprising a mixture. In this presentation, two of these approaches are described and compared. An overview of these approaches related to Canadian regulatory bodies is included, and a case study completes the account. The two approaches that are most well known in this area are: 1) that of the Massachusetts Dept. of Environmental Protection, and 2) that of the Total Petroleum Hydrocarbon Criteria Working Group. The integration of petroleum hydrocarbons in a quantitative evaluation of their toxological risk is possible by present methods. This integration allows a reduction in the uncertainty associated with the use of an integrating parameter in the case of these petroleum hydrocarbons in the C(10) to the C(50) range

Characterization of Petroleum Hydrocarbon Decomposing Fungi Isolated from Mangrove Rhizosphere

Directory of Open Access Journals (Sweden)

Nuni Gofar

2011-01-01

Full Text Available The research was done to obtain the isolates of soil borne fungi isolated from mangrove rhizosphere which were capable of degrading petroleum hydrocarbon compounds. The soil samples were collected from South Sumatra mangrove forest which was contaminated by petroleum. The isolates obtained were selected based on their ability to survive, to grow and to degrade polycyclic aromatic hydrocarbons in medium containing petroleum residue. There were 3 isolates of soil borne hydrocarbonoclastic fungi which were able to degrade petroleum in vitro. The 3 isolates were identified as Aspergillus fumigates, A. parasiticus, and Chrysonilia sitophila. C. sitophila was the best isolate to decrease total petroleum hydrocarbon (TPH from medium containing 5-20% petroleum residue.

Petroleum-hydrocarbons biodegradation by Pseudomonas strains ...

African Journals Online (AJOL)

The capability of these isolates to degrade petroleum was performed by measuring the optical density, colony forming unit counts (CFU/ml) and concentration of total petroleum hydrocarbons (TPH). Degradation of Isomerate by these isolates was analyzed by gas chromatography with flame ionization detector (FID). Results ...

Structural segregation of petroleum and prospective hydrocarbon regions in Azerbaijan

International Nuclear Information System (INIS)

Kerimov, K.M.; Huseynov, A.N.; Hajiyev, F.M.

2002-01-01

Full text : Structural segregation allows identify the earth crust blocks according to their geological setting and structural history conductive for hydrocarbon generation and their entrapment in the sedimentary fill reservoirs. Since then there has been a need to design a new tectonic map of petroleum and hydrocarbons potential systems in Azerbaijan embracing both on- and offshore areas. Map's legend designed upon above mentioned concepts and principles has made it possible to evaluate the role of individual stratigraphic units in hydrocarbon generation and its entrapment, as well as in recognition of regional structural criteria of the hydrocarbon bearing potential of different structural patterns. Tectonic map of petroleum and prospective hydrocarbon bearing on and offshore areas in Azerbaijan for the first time contained a wide range of information related to structural criteria of hydrocarbon bearing potential, sedimentary fill's structural architecture, its thickness, both timing of their formation stages and basement consolidation, its subsidence depth, as well as hydrocarbon deposit areal and vertical distribution across individual regions. This map was considered to be of important implication both for the petroleum geoscience and petroleum industry endeavors.

Petroleum hydrocarbon concentration in sediments along northern west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Ram, A.; Kadam, A.N.

Gas chromatography revealed that nonpolar material extracted from surface sediments collected along the northern west coast of India was originated from petroleum hydrocarbon residue. Petroleum hydrocarbon levels as determinEd. by fluorescence...

Petroleum hydrocarbon concentrations in eight mollusc species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Sudhakar, S; Raja, P; Rajeswari, V

2011-01-01

Eight mollusc species and sediment samples collected from three different stations along Tamilnadu coast, Bay of Bengal, India were analysed for the levels of petroleum hydrocarbons to elucidate the status of the petroleum residues in mollusc meant for human consumption. The concentrations of petroleum hydrocarbons in sediments along Tamilnadu coast varied from 5.04-25.5 microg/g dw (dry weight). High concentration of petroleum hydrocarbons in the sediment of Uppanar estuary (25.5 +/- 1.45 microg/g dw) was perhaps land and marine based anthropogenic sources of this region. The petroleum hydrocarbon residues in eight mollusc species collected from Uppanar, Vellar and Coleroon estuaries varied between 2.44-6.04 microg/g ww (wet weight). Although the concentration of petroleum hydrocarbons in sediment of the Uppanar region was markedly higher than the background, the petroleum hydrocarbon residues in mollusc collected from Uppanar estuary did not suggest bioaccumulation. The results signified that industrial growth has affected the aquatic environments and regular monitoring will help to adopt stringent pollution control measures for better management of the aquatic region.

Total petroleum hydrocarbons in edible marine biota from Northern Persian Gulf.

Science.gov (United States)

Nozar, Seyedeh Laili Mohebbi; Pauzi, Mohamad Zakaria; Salarpouri, Ali; Daghooghi, Behnam; Salimizadeh, Maryam

2015-04-01

To provide a baseline information for consumer's health, distribution of total petroleum hydrocarbons in 18 edible marine biota species from northern Persian Gulf was evaluated. The samples were purchased from fish market of Hormozgan Province, South of Iran. Marine biota samples included different species with various feeding habits and were analyzed based on ultraviolet florescence spectroscopy. Petroleum hydrocarbons showed narrow variation, ranging from 0.67 to 3.36 μg/g dry weight. The maximum value was observed in silver pomfret. Anchovy and silver pomfret with the highest content of petroleum hydrocarbons were known as good indicator for oil pollution in the studied area. From public health point of view, the detected concentrations for total petroleum hydrocarbons were lower than hazardous guidelines. The results were recorded as background data and information in the studied area; the continuous monitoring of pollutants is recommended, according to the rapid extension of industrial and oily activities in Hormozgan Province.

Field desorption mass spectroscopy monitoring of changes in hydrocarbon type composition during petroleum biodegradation

International Nuclear Information System (INIS)

Huesemann, M.H.

1995-01-01

A comprehensive petroleum hydrocarbon characterization procedure involving group type separation, boiling point distribution, and hydrocarbon typing by field desorption mass spectroscopy (FDMS) has been developed to quantify changes in hydrocarbon type composition during bioremediation of petroleum-contaminated soils. FDMS is able to quantify the concentration of hundreds of specific hydrocarbon types based on their respective hydrogen deficiency (z-number) and molecular weight (carbon number). Analytical results from two bioremediation experiments involving soil contaminated with crude oil and motor oil indicate that alkanes and two-ring saturates (naphthenes) were readily biodegradable. In addition, low-molecular-weight hydrocarbons generally were biodegraded to a larger extent than those of high molecular weight. More importantly, it was found that the extent of biodegradation of specific hydrocarbon types was comparable between treatments and appeared to be unaffected by the petroleum contaminant source, soil type, or experimental conditions. It was therefore concluded that in these studies the extent of total petroleum hydrocarbon (TPH) biodegradation is primarily affected by the molecular composition of the petroleum hydrocarbons present in the contaminated soil

Bioremediation of petroleum hydrocarbons in soil environments

International Nuclear Information System (INIS)

Rowell, M.J.; Ashworth, J.; Qureshi, A.A.

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs

Bioremediation of petroleum hydrocarbons in soil environments

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs.

Petroleum hydrocarbons in offshore sediments from the Gulf

International Nuclear Information System (INIS)

Al-Lihaibi, S.S.; Al-Omran, Laila

1996-01-01

Petroleum hydrocarbons in offshore sediments from the central part of the Gulf were measured using fluorescence spectrophotometry. Concentrations varied between 4.0 and 56.2 μg/g wet sediment (expressed as Kuwait Crude Oil equivalents), with an average of 12.3 μ/g. Highest concentrations were recorded in the north-west sector, with concentrations decreasing in a south-westerly direction. No significant correlations were observed between petroleum hydrocarbons and sedimentary organic carbon (r-0.07), 'mud' content (r=0.09), 'sand' content (r= -0.08) or 'gravel' content (r= -0.12). Distributions of oil are considered to relate more closely to prevailing current and localized pollutant sources in the region. Despite the substantial inputs of oil to the Gulf, contamination can be considered comparatively low, possibly reflecting physical processes and biological degradation which accelerate removal of petroleum from this marine environment. (author)

Toxicity of oils and petroleum hydrocarbons to estuarine crustaceans

Energy Technology Data Exchange (ETDEWEB)

Tatem, H.E. (Army Engineer Waterways Experiment Station, Vicksburg, MS); Cox, B.A.; Anderson, J.W.

1978-04-01

Bioassay experiments with various life stages of three estuarine shrimp and soluble petroleum hydrocarbons (PH) revealed residual Bunker C oil and refined No. 2 fuel oil to be more toxic than two crude oils tested. Larvae of Palaemonetes pugio were slightly more sensitive to the PH than adults, while young penaeid shrimp were shown to be more resistant than older, larger individuals. Shrimp exposed to PH in conjunction with temperature and salinity changes were more susceptible to the PH. Some common aromatic and diaromatic PH, including three naphthalene compounds, were utilized in bioassays. Naphthalenes were highly toxic. The toxicity of petroleum products is closely related to aromatic hydrocarbon content, especially the naphthalenes and related hydrocarbons.

Earthworm-assisted bioremediation of petroleum hydrocarbon ...

African Journals Online (AJOL)

Ameh

The use of earthworms (Eudrilus eugenia) for vermi-assisted bioremediation of petroleum hydrocarbon contaminated mechanic workshop soils ... not always result in complete neutrali- zation of pollutants (Yerushalmi et al., 2003). ..... Screening of biofouling activity in marine bacterial isolate from ship hull. Int. J. Environ. Sci.

Biological effects of petroleum hydrocarbons: Predictions of long-term effects and recovery

International Nuclear Information System (INIS)

Capuzzo, J.M.

1990-01-01

Biological effects of petroleum hydrocarbons on marine organisms and ecosystems are dependent on the persistence and bioavailability of specific hydrocarbons, the ability of organisms to accumulate and metabolize various hydrocarbons, the fate of metabolized products, and the interference of specific hydrocarbons with normal metabolic processes that may alter an organism's chances for survival and reproduction in the environment. In considering the long-term effects of petroleum hydrocarbons on marine ecosystems it is important to ascertain what biological effects may result in subtle ecological changes, changes in community structure and function, and possible impairment of fisheries resources. It is also important to understand which hydrocarbons persist in benthic environments and the sublethal effects that lead to reduced growth, delayed development and reduced reproductive effort, population decline and the loss of that population's function in marine communities. Only through a multi-disciplinary approach to the study of the fate, transport and effects of petroleum hydrocarbons on marine ecosystems will there be a significant improvement in the ability to predict the long-term effects of oil spills and to elucidate the mechanisms of recovery

Prospects of using leguminous species in phytoremediation of total petroleum hydrocarbons polluted soils

Directory of Open Access Journals (Sweden)

Smaranda Masu

2014-05-01

Full Text Available Selecting the plant species to grow on aged petroleum hydrocarbons polluted soils is an important factor for a successful phytoremediation. Phytoremediation is a green technology that can become a promising solution for decontaminating polluted soils and ecological restoration of the landscape. Our comparative studies evaluate the effect of oil hydrocarbon pollution with high initial concentration on the growth leguminous plant species: Vicia sativa and Glycine max. The experimental block contains control variants, polluted soil unfertilized / fertilized with municipal sludge anaerobically stabilized in absence/presence of modified volcanic tuff amendment. After period of time the experiment’s soil in which plant species had grown well was sampled and analyzed for petroleum hydrocarbons removal. Both species showed promising efficiency in the phytoremediation of petroleum hydrocarbon highly polluted soils but a reduced growth of the surveyed plants was noticed. The efficiency of the petroleum hydrocarbons diminution is increased in the case of the addition of fertilizer 16.6 % for Vicia sativa and 30 % for Glycine max vs. the initial quantity. In the case of the phytoremediation of polluted soils treated with fertilizer and volcanic tuff, the efficiency of the petroleum hydrocarbons reduction was 72.9 % for Vicia sativa and 53.7 % for Glycine max.

Analysis of petroleum hydrocarbons in soil from view of bioremediation process

International Nuclear Information System (INIS)

Mracnova, R.; Sojak, L.; Kubinec, R.; Kraus, A.; Eszenyiova, A.; Ostrovsky, I.

2002-01-01

The pollution of the environment by petroleum hydrocarbons is the most often pollution of them all. Nevertheless, hydrocarbons present in environment can be not only of petroleum or anthropogenic origin, but of biogenic as well. Typically the hydrocarbons are presented in the environment as very complex mixtures of individual compounds with very different chemical structure, wide range of the boiling points (∼800 0 C) as well as with the wide range of the number of carbon atoms. Immediately they are spread in any environmental matrix the complex physical, chemical and biochemical reactions start. A lot of methods have been developed and new are permanently in progress for the monitoring and control of petroleum hydrocarbons contamination and/or soils bioremediation. Generally, all methods by whose the hydrocarbons contaminants are determined in GC-FID system do not satisfied recommendations for enough accurate and precise results. Hyphenation of capillary gas chromatography and mass selective detector operated in the selective ion monitoring mode essentially allows detailed specification of non-polar extractable hydrocarbons. Isoprenoid alkanes, alkylhomologues of aromatic hydrocarbons and polycyclic alkanes hopanes-like were investigated as markers for recognition of petroleum and biogenic contamination. C 30 17α(H)21β(H)-hopane (C 30 -hopane) seems to be a suitable marker to identify hydrocarbons origin, to determine composting rates for nonpolar extractable compounds and to calculate real content of non-polar extractable compounds in final composting status on the assumption that the contamination is of mineral oil type. This is the survey into the results obtained in this field published in the literature as well as reached in our laboratory. (author)

Comparative survey of petroleum hydrocarbons i lake sediments

Energy Technology Data Exchange (ETDEWEB)

Wakeham, S G

1976-11-01

Hydrocarbon distribution in sediments from three lakes in Washington State were studied and found to be related to the level of human activity in the respective drainage basins. Petroleum hydrocarbon contamination was found in surface sediments of a lake surrounded by a major city, compared to no detectable contamination in a lake located in a National Park.

Bioavailability enhanced rhizosphere remediation of petroleum hydrocarbon contaminated soil

International Nuclear Information System (INIS)

Marchenko, A.; Vorobyov, A.; Zharikov, G.; Ermolenko, Z.; Dyadishchev, N.; Borovick, R.; Sokolov, M.; Ortega-Calvo, J.J.

2005-01-01

Aliphatic, aromatic and polycyclic aromatic oil hydrocarbons are structurally complicated man-caused pollutants that are constantly brought into biosphere. Oil production in Russia, so as all over the world, is connected with pollution of biotopes, ecosystems and agro-landscapes. Presently large funds are allocated either for oil leak prevention or for discharged oil gathering. At the same time, in spite of large necessity in technologies for efficient reconstruction of soil bio-productivity, reliable regional systems of their remediation in situ have not been developed yet. One such method is rhizosphere remediation, a biotechnology, based on the functioning of plant-microbial complexes. Little is known about bioavailability in phyto-remediation systems. Specific bioavailability-promoting mechanisms, operating in soil with hydrocarbon-degrading populations, may be responsible for increased rates of pollutant transformation (increased bacterial adherence to the pollutants, production of bio-surfactants by bacteria or by plants, possible role of chemotaxis). In the course of work collection of 42 chemo-tactically active bio-surfactant producing strain-degraders of petroleum hydrocarbons including polycyclic aromatic hydrocarbons (PAHs) was created. Two representative strains were selected for detailed chemotaxis studies with PAHs (naphthalene, phenanthrene, anthracene, and pyrene), bacterial lipopolysaccharide and root exudates from seven different plants. These strains are produce the bio-surfactants (rhamno-lipid). The chemotactic response was quantified with a capillary and densitometric chemotaxis assay. Surface tension of cultural liquid was measured after cultivation of strains in the presence of hexadecane or phenanthrene with the use of a ring tensiometer. Before measuring of surface tension microbial cells were collected from liquid culture by centrifugation. Total petroleum Hydrocarbons (TPH) in soil were analyzed by infra-red spectroscopy method. PAHs

Bioavailability enhanced rhizosphere remediation of petroleum hydrocarbon contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Marchenko, A.; Vorobyov, A.; Zharikov, G.; Ermolenko, Z.; Dyadishchev, N.; Borovick, R.; Sokolov, M. [Research Centre for Toxicology and Hygienic Regulation of Biopreparations, Moscow region (Russian Federation); Ortega-Calvo, J.J. [Instituto de Recursos Naturales y Agrobiologia, CSIC, Sevilla (Spain)

2005-07-01

Aliphatic, aromatic and polycyclic aromatic oil hydrocarbons are structurally complicated man-caused pollutants that are constantly brought into biosphere. Oil production in Russia, so as all over the world, is connected with pollution of biotopes, ecosystems and agro-landscapes. Presently large funds are allocated either for oil leak prevention or for discharged oil gathering. At the same time, in spite of large necessity in technologies for efficient reconstruction of soil bio-productivity, reliable regional systems of their remediation in situ have not been developed yet. One such method is rhizosphere remediation, a biotechnology, based on the functioning of plant-microbial complexes. Little is known about bioavailability in phyto-remediation systems. Specific bioavailability-promoting mechanisms, operating in soil with hydrocarbon-degrading populations, may be responsible for increased rates of pollutant transformation (increased bacterial adherence to the pollutants, production of bio-surfactants by bacteria or by plants, possible role of chemotaxis). In the course of work collection of 42 chemo-tactically active bio-surfactant producing strain-degraders of petroleum hydrocarbons including polycyclic aromatic hydrocarbons (PAHs) was created. Two representative strains were selected for detailed chemotaxis studies with PAHs (naphthalene, phenanthrene, anthracene, and pyrene), bacterial lipopolysaccharide and root exudates from seven different plants. These strains are produce the bio-surfactants (rhamno-lipid). The chemotactic response was quantified with a capillary and densitometric chemotaxis assay. Surface tension of cultural liquid was measured after cultivation of strains in the presence of hexadecane or phenanthrene with the use of a ring tensiometer. Before measuring of surface tension microbial cells were collected from liquid culture by centrifugation. Total petroleum Hydrocarbons (TPH) in soil were analyzed by infra-red spectroscopy method. PAHs

Microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock

Energy Technology Data Exchange (ETDEWEB)

Akinlua, A., E-mail: geochemresearch@yahoo.com [Fossil Fuels and Environmental Geochemistry Group, Department of Chemistry, Obafemi Awolowo University, Ile-Ife (Nigeria); Jochmann, M.A.; Laaks, J.; Ewert, A.; Schmidt, T.C. [Instrumental Analytical Chemistry, University Duisburg-Essen, Universitaetsstr, 5, 45141 Essen (Germany)

2011-04-08

The extraction of aliphatic hydrocarbons from petroleum source rock using nonionic surfactants with the assistance of microwave was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and kinetic rates have significant effects on extraction yields of aliphatic hydrocarbons. The optimum temperature for microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock was 105 deg. C. The optimum extraction time for the aliphatic hydrocarbons was at 50 min. Concentration of the nonionic surfactant solution and irradiation power had significant effect on the yields of aliphatic hydrocarbons. The yields of the analytes were much higher using microwave assisted nonionic surfactant extraction than with Soxhlet extraction. The recoveries of the n-alkanes and acyclic isoprenoid hydrocarbons for GC-MS analysis from the extractant nonionic surfactant solution by in-tube extraction (ITEX 2) with a TENAX TA adsorbent were found to be efficient. The results show that microwave-assisted nonionic surfactant extraction (MANSE) is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.

Microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock

International Nuclear Information System (INIS)

Akinlua, A.; Jochmann, M.A.; Laaks, J.; Ewert, A.; Schmidt, T.C.

2011-01-01

The extraction of aliphatic hydrocarbons from petroleum source rock using nonionic surfactants with the assistance of microwave was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and kinetic rates have significant effects on extraction yields of aliphatic hydrocarbons. The optimum temperature for microwave-assisted nonionic surfactant extraction of aliphatic hydrocarbons from petroleum source rock was 105 deg. C. The optimum extraction time for the aliphatic hydrocarbons was at 50 min. Concentration of the nonionic surfactant solution and irradiation power had significant effect on the yields of aliphatic hydrocarbons. The yields of the analytes were much higher using microwave assisted nonionic surfactant extraction than with Soxhlet extraction. The recoveries of the n-alkanes and acyclic isoprenoid hydrocarbons for GC-MS analysis from the extractant nonionic surfactant solution by in-tube extraction (ITEX 2) with a TENAX TA adsorbent were found to be efficient. The results show that microwave-assisted nonionic surfactant extraction (MANSE) is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.

Towards minimizing measurement uncertainty in total petroleum hydrocarbon determination by GC-FID

Energy Technology Data Exchange (ETDEWEB)

Saari, E.

2009-07-01

Despite tightened environmental legislation, spillages of petroleum products remain a serious problem worldwide. The environmental impacts of these spillages are always severe and reliable methods for the identification and quantitative determination of petroleum hydrocarbons in environmental samples are therefore needed. Great improvements in the definition and analysis of total petroleum hydrocarbons (TPH) were finally introduced by international organizations for standardization in 2004. This brought some coherence to the determination and, nowadays, most laboratories seem to employ ISO/DIS 16703:2004, ISO 9377-2:2000 and CEN prEN 14039:2004:E draft international standards for analysing TPH in soil. The implementation of these methods, however, usually fails because the reliability of petroleum hydrocarbon determination has proved to be poor.This thesis describes the assessment of measurement uncertainty for TPH determination in soil. Chemometric methods were used to both estimate the main uncertainty sources and identify the most significant factors affecting these uncertainty sources. The method used for the determinations was based on gas chromatography utilizing flame ionization detection (GC-FID).Chemometric methodology applied in estimating measurement uncertainty for TPH determination showed that the measurement uncertainty is in actual fact dominated by the analytical uncertainty. Within the specific concentration range studied, the analytical uncertainty accounted for as much as 68-80% of the measurement uncertainty. The robustness of the analytical method used for petroleum hydrocarbon determination was then studied in more detail. A two-level Plackett-Burman design and a D-optimal design were utilized to assess the main analytical uncertainty sources of the sample treatment and GC determination procedures. It was also found that the matrix-induced systematic error may also significantly reduce the reliability of petroleum hydrocarbon determination

BioDegradation of Refined Petroleum Hydrocarbons in Soil | Obire ...

African Journals Online (AJOL)

Carbon-dioxide production and hydrocarbon degradation of refined petroleum hydrocarbon in soils treated with 5% gasoline, kerosene and diesel oil were investigated. Soil for study was bulked from around a car park in Port Harcourt. Soil samples were collected at weekly intervals for four weeks and subsequently at ...

Petroleum hydrocarbon concentrations in ten commercial fish species along Tamilnadu coast, Bay of Bengal, India.

Science.gov (United States)

Veerasingam, S; Venkatachalapathy, R; Raja, P; Sudhakar, S; Rajeswari, V; Asanulla, R Mohamed; Mohan, R; Sutharsan, P

2011-05-01

The aim of the present study was to evaluate the distribution of petroleum hydrocarbons in ten commercial fish species and water samples in three estuaries along Tamilnadu coast, Bay of Bengal, India. Fish and water samples collected from Tamilnadu coast, India, were extracted and analyzed for petroleum hydrocarbons by ultraviolet fluorescence (UVF) spectroscopy. The petroleum hydrocarbon concentration (PHC) in coastal waters and fish species varied between 2.28 and 14.02 μg/l and 0.52 and 2.05 μg/g, respectively. The highest PHC concentration was obtained in Uppanar estuarine waters (14.02 ± 0.83) and the lowest was observed in Vellar estuarine waters (2.28 ± 0.25). Among the ten fish species, Sardinella longiceps have high PHC concentration from all the locations. This study suggests that S. longiceps can be used as a good biological indicator for petroleum hydrocarbon pollution in water. The concentration of petroleum hydrocarbons in coastal waters along Tamilnadu coast is markedly higher than that in the background, but there is no evidence for its increase in fish of this region. From a public health point, petroleum hydrocarbon residue levels in all fish samples analyzed in this study are considerably lower than the hazardous levels. At present, as Tamilnadu coastal area is in a rapid development stage of new harbour, chemical industries, power plants, oil exploration and other large-scale industries, further assessment of petroleum hydrocarbons and the various hydrodynamic conditions acting in the region are to be studied in detail and continuous pollution monitoring studies should be conducted for improving the aquatic environment. The results will also be useful for pollution monitoring program along the coastal region and also to check the levels of petroleum hydrocarbons.

A proposal for revised Intervention Values for petroleum hydrocarbons ('minerale olie') on base of fractions of petroleum hydrocarbons

NARCIS (Netherlands)

Franken ROG; Baars AJ; Crommentuijn GH; Otte P; LBG

1999-01-01

The present Dutch intervention values for mineral oil (i.e. 'Total Petroleum Hydrocarbons') have been reviewed with respect to fractions of TPH and using ecotoxicological and human toxicological data. It is found that review of TPH-fractions is significant with respect to both human and ecological

The internal combustion engine; a simple solution for pollution from petroleum hydrocarbons

International Nuclear Information System (INIS)

Johnson, G.A.

1992-01-01

The internal combustion (IC) engine is an indirect cause of groundwater and soil contamination from petroleum hydrocarbons. Leaking underground storage tank systems that are used to store and distribute fuel for automobiles are a major cause of environmental degradation. That same IC engine which has indirectly caused the pollution is an excellent tool for cleaning up environmental contamination from petroleum releases. An extremely flexible clean-up system using an IC engine was designed, constructed and operated to recover free product, treat contaminated soil and remediate groundwater pollution. The treatment system uses the IC engine for vapor extraction, groundwater pumping, spray aeration and incineration. The IC engine is an excellent incinerator. The petroleum vapors are burned in the IC engine with a supplemental propane fuel. The engine drives a power-takeoff unit and provides energy for an air compressor, water pump, electrical generation and other accessories. Using waste to energy methods multiple techniques are being used in combination with different treatment technologies to optimize the remediation. As the remediation progresses the treatment system can be modified to use additional techniques. Another benefit that is directly associated with the IC engine is the presence of excess heat which is helpful in northern climates. The excess heat has many uses including spray aeration and enhanced biological remediation. The IC engine has several limitations and requires an understanding of the physical and chemical properties of the contamination. As with all environmental remediation, a proper understanding of the Hydrogeological System is critical. When properly applied the IC engine has many advantages over other methods of remediation for petroleum hydrocarbons

Petroleum Hydrocarbons Contamination Profile of Ochani Stream in ...

African Journals Online (AJOL)

Michael Horsfall

ABSTRACT: Petroleum hydrocarbon contamination profile, heavy metals and .... potential conduits for oil and water migrating from the ... by Gas Chromatography: Soil / sediment / sludge ..... fractions contained in the dump pits) which have.

Studies on the effect of petroleum hydrocarbon on the microbial and ...

African Journals Online (AJOL)

SERVER

2007-08-20

Aug 20, 2007 ... Key words: Hydrocarbon, microbial counts, physico-chemical characteristics. INTRODUCTION. Petroleum ... carbons, whose composition also varies with the source. ... hydrocarbons into aquifers can lead to concentrations of.

Environmental hazard and risk characterisation of petroleum substances: a guided "walking tour" of petroleum hydrocarbons.

Science.gov (United States)

Bierkens, Johan; Geerts, Lieve

2014-05-01

Petroleum substances are used in large quantities, primarily as fuels. They are complex mixtures whose major constituents are hydrocarbons derived from crude oil by distillation and fractionation. Determining the complete molecular composition of petroleum and its refined products is not feasible with current analytical techniques because of the huge number of molecular components. This complex nature of petroleum products, with their varied number of constituents, all of them exhibiting different fate and effect characteristics, merits a dedicated hazard and risk assessment approach. From a regulatory perspective they pose a great challenge in a number of REACH processes, in particular in the context of dossier and substance evaluation but also for priority setting activities. In order to facilitate the performance of hazard and risk assessment for petroleum substances the European oil company association, CONCAWE, has developed the PETROTOX and PETRORISK spreadsheet models. Since the exact composition of many petroleum products is not known, an underlying assumption of the PETROTOX and PETRORISK tools is that the behaviour and fate of a total petroleum substance can be simulated based on the physical-chemical properties of representative structures mapped to hydrocarbon blocks (HBs) and on the relative share of each HB in the total mass of the product. To assess how differing chemical compositions affect the simulated chemical fate and toxicity of hydrocarbon mixtures, a series of model simulations were run using an artificial petroleum substance, containing 386 (PETROTOX) or 160 (PETRORISK) HBs belonging to different chemical classes and molecular weight ranges, but with equal mass assigned to each of them. To this artificial petroleum substance a guided series of subsequent modifications in mass allocation to a delineated number of HBs belonging to different chemical classes and carbon ranges was performed, in what we perceived as a guided "walking tour

Comprehensive review on toxicity of persistent organic pollutants from petroleum refinery waste and their degradation by microorganisms.

Science.gov (United States)

Varjani, Sunita J; Gnansounou, Edgard; Pandey, Ashok

2017-12-01

Control and prevention of environmental pollution has become a worldwide issue of concern. Aromatic hydrocarbons including benzene, toluene, ethyl benzene, xylene (BTEX) and polyaromatic hydrocarbons (PAHs) are persistent organic pollutants (POPs), released into the environment mainly by exploration activities of petroleum industry. These pollutants are mutagenic, carcinogenic, immunotoxic and teratogenic to lower and higher forms of life i.e. microorganisms to humans. According to the International Agency for Research on Cancer (IARC) and United States Environmental Protection Agency (U.S. EPA), Benzo[a]pyrene (BaP) is carcinogenic in laboratory animals and humans. Aromatic hydrocarbons are highly lipid soluble and thus readily absorbed from environment in gastrointestinal tract of mammals. Treatment and remediation of petroleum refinery waste have been shown either to reduce or to eliminate genotoxicity of these pollutants. Bioremediation by using microorganisms to treat this waste is showing a promising technology as it is safe and cost-effective option among various technologies tested. The main aim of this review is to provide contemporary information on variety of aromatic hydrocarbons present in crude oil (with special focus to mono- and poly-aromatic hydrocarbons), exposure routes and their adverse effects on humans. This review also provides a synthesis of scientific literature on remediation technologies available for aromatic hydrocarbons, knowledge gaps and future research developments in this field. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mathematical modelling on transport of petroleum hydrocarbons in ...

Indian Academy of Sciences (India)

Groundwater being the world's most extracted raw material, with withdrawal rates .... and analytical results, while Petroleum Hydro-Carbons (PHC) generally ... and pipeline ruptures form the major source of groundwater contamination by ...

Remediation of total petroleum hydrocarbons using combined in-vessel composting ‎and oxidation by activated persulfate

Directory of Open Access Journals (Sweden)

A.R. Asgari

2017-12-01

Full Text Available This study was investigated the efficiency of activated persulfate and ‎in-vessel composting for removal of total petroleum hydrocarbons. ‎Remediation by activated persulfate with ferrous sulfate as pre-treatment was done at batch system. In the chemical oxidation, various variables including persulfate concentrations (10-3000 mg/g as waste, pH (3-7, ferrous sulfate (0.5-4 mg/g as wasteand temperature (20-60°C were studied. In the biological system, premature compost was added as an amendment. The filter cake to compost ratio were 1:0 (as control and 1:5 to 15 (as dry basis. C: N: P ratio and moisture content were 100:5:1 and 45-60%, respectively. The results showed that acidic pH (pH=3 had high efficiency for the removal of total petroleum hydrocarbons by activated persulfate. Temperature had the significant effect during the persulfate oxidation. When ferrous sulfate was used as an activator for degradation at acidic condition and 60°C, removal efficiency increased to 47.32%. The results of biological process showed that the minimum total petroleum hydrocarbons removal in all reactors was 62 percent. The maximum and minimum removal efficiency was obtained at 1:5 (69.46% and 1:10 (62.42% mixing ratios, respectively. Kinetic study showed that second order kinetic model (R2>0.81 shows the best agreement with the experimental data and the rate of TPH degradation at low mixing ratio (1:3 was faster than high mixing ratio (1:15. Therefore, according to the results, in-vessel composting after pre-treatment by activated persulfate is suggested as an efficient process for degradation of total petroleum hydrocarbons.

Biological Remediation of Petroleum Contaminants

Science.gov (United States)

Kuhad, Ramesh Chander; Gupta, Rishi

Large volumes of hazardous wastes are generated in the form of oily sludges and contaminated soils during crude oil transportation and processing. Although many physical, chemical and biological treatment technologies are available for petroleum contaminants petroleum contaminants in soil, biological methods have been considered the most cost-effective. Practical biological remediation methods typically involve direct use of the microbes naturally occurring in the contaminated environment and/or cultured indigenous or modified microorganisms. Environmental and nutritional factors, including the properties of the soil, the chemical structure of the hydrocarbon(s), oxygen, water, nutrient availability, pH, temperature, and contaminant bioavailability, can significantly affect the rate and the extent of hydrocarbon biodegradation hydrocarbon biodegradation by microorganisms in contaminated soils. This chapter concisely discusses the major aspects of bioremediation of petroleum contaminants.

Dissolved petroleum hydrocarbons in the Andaman Sea

Digital Repository Service at National Institute of Oceanography (India)

Topgi, R.S.; Noronha, R.J.; Fondekar, S.P.

Mean dissolved petroleum hydrocarbons, measured using UV-spectrophotometry, at 0 and 10m were 51 plus or minus 1 and 55 plus or minus 1.2 mu g/litre respectively; range of variation being between 28 and 83 mu g/litre. Very little difference...

Bioremediation of petroleum hydrocarbons in soil environments. Report No. EE-141

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-01-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed by means of a literature survey and also through discussions with workers in relevent disciplines. This report discusses both the impacts of hydrocarbons on soil and a range of methods available to assist in the decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, oily sludges, asphalts and bitumens, drilling mud residues, creosote tars and some pesticides.

Petroleum hydrocarbon concentrations in marine sediments along Chennai Coast, Bay of Bengal, India.

Science.gov (United States)

Venkatachalapathy, R; Veerasingam, S; Ramkumar, T

2010-10-01

The spatial and temporal distribution of petroleum hydrocarbons (PHC) in marine sediments along the Chennai coast, Bay of Bengal was quantified by Ultra-Violet Fluorescence (UVF) Spectroscopy. The concentration of PHC in surface sediments varied from 1.88 to 39.76 ppm. The highest values obtained in the northern part of the study area, where shipping activities and land-based waste waters disposed into sea through the rivers like Kuvam and Adayar. The Adayar (7.26-16.83 ppm) and Kuvam (5.5-39.72 ppm) cores reveal a clear horizon of increase in PHC above 50 and 35 cm respectively. PHC values showed a decreasing pattern with depth in all sediment cores suggesting the excess anthropogenic loading occurring in the recent past. The present study revealed that the PHC values of Chennai coastal sediments are lower than the values reported from selected costal areas including the sediment of the Mumbai coast (7.6-42.8 ppm), Arabian Sea. The results will be useful for pollution monitoring program along the coastal region and also to check the level of petroleum hydrocarbons in marine sediments.

A method for predicting the extent of petroleum hydrocarbon biodegradation in contaminated soils

International Nuclear Information System (INIS)

Huesemann, M.H.

1994-01-01

A series of solid- and slurry-phase soil bioremediation experiments involving different crude oils and refined petroleum products were performed to investigate the factors which affect the maximum extent of total petroleum hydrocarbon (TPH) biodegradation. The authors used a comprehensive petroleum hydrocarbon characterization procedure involving group-type separation analyses, boiling-point distributions, and hydrocarbon typing by field ionization mass spectroscopy. Initial and final concentrations of specified hydrocarbon classes were determined in each of seven different bioremediation treatments. Generally, they found that the degree of TPH biodegradation was affected mainly by the type of hydrocarbons in the contaminant matrix. In contrast, the influence of experimental variables such as soil type, fertilizer concentrations, microbial plate counts, and treatment type (slurry versus landfarming) on the overall extent of TPH biodegradation was insignificant. Based on these findings, a predictive algorithm was developed to estimate the extent of TPH biodegradation from the average reduction of 86 individual hydrocarbon classes and their respective initial concentrations. Model predictions for gravimetric TPH removals were in close agreement with analytical results from two independent laboratories

Investigating bioremediation of petroleum hydrocarbons through landfarming using apparent electrical conductivity measurements

Science.gov (United States)

Van De Vijver, Ellen; Van Meirvenne, Marc; Seuntjens, Piet

2015-04-01

Bioremediation of soil contaminated with petroleum hydrocarbons through landfarming has been widely applied commercially at large scale. Biodegradation is one of the dominant pollutant removal mechanisms involved in landfarming, but strongly depends on the environmental conditions (e.g. presence of oxygen, moisture content). Conventionally the biodegradation process is monitored by the installation of field monitoring equipment and repeated sample collection and analysis. Because the presence of petroleum hydrocarbons and their degradation products can affect the electrical properties of the soil, proximal soil sensors such as electromagnetic induction (EMI) sensors may provide an alternative to investigate the biodegradation process of these contaminants. We investigated the relation between the EMI-based apparent electrical conductivity (ECa) of a landfarm soil and the presence and degradation status of petroleum hydrocarbons. The 3 ha study area was located in an oil refinery complex contaminated with petroleum hydrocarbons, mainly composed of diesel. At the site, a landfarm was constructed in 1999. The most recent survey of the petroleum hydrocarbon concentrations was conducted between 2011 and 2013. The sampling locations were defined by a grid with a 10 m by 10 m cell size and on each location a sample was taken from four successive soil layers with a thickness of 0.5 m each. Because the survey was carried out in phases using different georeferencing methods, the final dataset suffered from uncertainty in the coordinates of the sampling locations. In September 2013 the landfarm was surveyed for ECa with a multi-receiver electromagnetic induction sensor (DUALEM-21S) using motorized conveyance. The horizontal measurement resolution was 1 m by 0.25 m. On each measurement location the sensor recorded four ECa values representative of measurement depths of 0.5 m, 1.0 m, 1.6 m and 3.2 m. After the basic processing, the ECa measurements were filtered to remove

Petroleum-hydrocarbon utilization by native bacterial population ...

African Journals Online (AJOL)

Two Nigerian crude oils (Bonny light and Escravos blend) were exposed to the wastewater canal via oil impregnated membrane filters (0.45 μm diameter) for 21 days in a microcosm experiment. Bacterial petroleum-hydrocarbon utilizers were later harvested from both the millipore membrane filters and laboratory ...

Bioremediation of hydrocarbon degradation in a petroleum-contaminated soil and microbial population and activity determination.

Science.gov (United States)

Wu, Manli; Li, Wei; Dick, Warren A; Ye, Xiqiong; Chen, Kaili; Kost, David; Chen, Liming

2017-02-01

Bioremediation of hydrocarbon degradation in petroleum-polluted soil is carried out by various microorganisms. However, little information is available for the relationships between hydrocarbon degradation rates in petroleum-contaminated soil and microbial population and activity in laboratory assay. In a microcosm study, degradation rate and efficiency of total petroleum hydrocarbons (TPH), alkanes, and polycyclic aromatic hydrocarbons (PAH) in a petroleum-contaminated soil were determined using an infrared photometer oil content analyzer and a gas chromatography mass spectrometry (GC-MS). Also, the populations of TPH, alkane, and PAH degraders were enumerated by a modified most probable number (MPN) procedure, and the hydrocarbon degrading activities of these degraders were determined by the Biolog (MT2) MicroPlates assay. Results showed linear correlations between the TPH and alkane degradation rates and the population and activity increases of TPH and alkane degraders, but no correlation was observed between the PAH degradation rates and the PAH population and activity increases. Petroleum hydrocarbon degrading microbial population measured by MPN was significantly correlated with metabolic activity in the Biolog assay. The results suggest that the MPN procedure and the Biolog assay are efficient methods for assessing the rates of TPH and alkane, but not PAH, bioremediation in oil-contaminated soil in laboratory. Copyright © 2016 Elsevier Ltd. All rights reserved.

Recent Advances in Petroleum Microbiology

Science.gov (United States)

Van Hamme, Jonathan D.; Singh, Ajay; Ward, Owen P.

2003-01-01

Recent advances in molecular biology have extended our understanding of the metabolic processes related to microbial transformation of petroleum hydrocarbons. The physiological responses of microorganisms to the presence of hydrocarbons, including cell surface alterations and adaptive mechanisms for uptake and efflux of these substrates, have been characterized. New molecular techniques have enhanced our ability to investigate the dynamics of microbial communities in petroleum-impacted ecosystems. By establishing conditions which maximize rates and extents of microbial growth, hydrocarbon access, and transformation, highly accelerated and bioreactor-based petroleum waste degradation processes have been implemented. Biofilters capable of removing and biodegrading volatile petroleum contaminants in air streams with short substrate-microbe contact times (desulfurization processes with biodesulfurization methods through promotion of selective sulfur removal without degradation of associated carbon moieties. However, since microbes require an environment containing some water, a two-phase oil-water system must be established to optimize contact between the microbes and the hydrocarbon, and such an emulsion is not easily created with viscous crude oil. This challenge may be circumvented by application of the technology to more refined gasoline and diesel substrates, where aqueous-hydrocarbon emulsions are more easily generated. Molecular approaches are being used to broaden the substrate specificity and increase the rates and extents of desulfurization. Bacterial processes are being commercialized for removal of H2S and sulfoxides from petrochemical waste streams. Microbes also have potential for use in removal of nitrogen from crude oil leading to reduced nitric oxide emissions provided that technical problems similar to those experienced in biodesulfurization can be solved. Enzymes are being exploited to produce added-value products from petroleum substrates, and

Soil bioremediation approaches for petroleum hydrocarbon polluted environments

Directory of Open Access Journals (Sweden)

Eman Koshlaf

2017-01-01

Full Text Available Increasing industrialisation, continued population growth and heavy demand and reliance on petrochemical products have led to unprecedented economic growth and development. However, inevitably this dependence on fossil fuels has resulted in serious environmental issues over recent decades. The eco-toxicity and the potential health implications that petroleum hydrocarbons pose for both environmental and human health have led to increased interest in developing environmental biotechnology-based methodologies to detoxify environments impacted by petrogenic compounds. Different approaches have been applied for remediating polluted sites with petroleum derivatives. Bioremediation represents an environmentally sustainable and economical emerging technology for maximizing the metabolism of organic pollutants and minimizing the ecological effects of oil spills. Bioremediation relies on microbial metabolic activities in the presence of optimal ecological factors and necessary nutrients to transform organic pollutants such as petrogenic hydrocarbons. Although, biodegradation often takes longer than traditional remediation methods, the complete degradation of the contaminant is often accomplished. Hydrocarbon biodegradation in soil is determined by a number of environmental and biological factors varying from site to site such as the pH of the soil, temperature, oxygen availability and nutrient content, the growth and survival of hydrocarbon-degrading microbes and bioavailability of pollutants to microbial attack. In this review we have attempted to broaden the perspectives of scientists working in bioremediation. We focus on the most common bioremediation technologies currently used for soil remediation and the mechanisms underlying the degradation of petrogenic hydrocarbons by microorganisms.

Mathematical modelling on transport of petroleum hydrocarbons

Indian Academy of Sciences (India)

A brief theory has been included on the composition and transport of petroleum hydrocarbons following an onshore oil spill in order to demonstrate the level of complexity associated with the LNAPL dissolution mass transfer even in a classical porous medium. However, such studies in saturated fractured rocks are highly ...

Bioremediation of a Petroleum-Hydrocarbon Polluted Agricultural ...

African Journals Online (AJOL)

A combination of field cells involving a control and five treatment cells were evaluated under field conditions in the bioremediation of a petroleum- hydrocarbon polluted agricultural soil over a six-week period. Previous works have indicated that crude oil contamination of soils depletes oxygen reserves in the soils and slows ...

Surfactant-enhanced recovery of dissolved hydrocarbons at petroleum production facilities

International Nuclear Information System (INIS)

Freeman, J.T.; Mayes, M.; Wassmuth, F.; Taylor, K.; Rae, W.; Kuipers, F.

1997-01-01

The feasibility and cost effectiveness of surfactant-enhanced pumping to reduce source concentrations of petroleum hydrocarbons from contaminated soils was discussed. Light non-aqueous phase liquids (LNAPL) hydrocarbons are present beneath many petroleum production processing facilities in western Canada. Complete removal of LNAPLs from geologic materials is difficult and expensive. Treatment technologies include costly ex-situ methods such as excavation and in-situ methods such as physical extraction by soil venting and pumping, bioremediation, and combination methods such as bioventing, bioslurping or air sparging. Surfactant-aided pumping can reduce source hydrocarbon concentrations when used in conjunction with traditional pump and treat, or deep well injection. This study involved the selection of an appropriate surfactant from a wide variety of commercially available products. A site contaminated by hydrocarbons in Turner Valley, Alberta, was used for field scale testing. One of the major problems was quantifying the increase in the dissolved hydrocarbon concentrations in the recovered water once a surfactant was added. From the 30 surfactants screened in a series of washing and oil solubilization tests, two surfactants, Brij 97 and Tween 80, were selected for further evaluation. Increased hydrocarbon recovery was observed within 10 days of the introduction of the first surfactant. 2 refs., 7 figs

Sand amendment enhances bioelectrochemical remediation of petroleum hydrocarbon contaminated soil.

Science.gov (United States)

Li, Xiaojing; Wang, Xin; Ren, Zhiyong Jason; Zhang, Yueyong; Li, Nan; Zhou, Qixing

2015-12-01

Bioelectrochemical system is an emerging technology for the remediation of soils contaminated by petroleum hydrocarbons. However, performance of such systems can be limited by the inefficient mass transport in soil. Here we report a new method of sand amendment, which significantly increases both oxygen and proton transports, resulting to increased soil porosity (from 44.5% to 51.3%), decreased Ohmic resistance (by 46%), and increased charge output (from 2.5 to 3.5Cg(-1)soil). The degradation rates of petroleum hydrocarbons increased by up to 268% in 135d. The degradation of n-alkanes and polycyclic aromatic hydrocarbons with high molecular weight was accelerated, and denaturing gradient gel electrophoresis showed that the microbial community close to the air-cathode was substantially stimulated by the induced current, especially the hydrocarbon degrading bacteria Alcanivorax. The bioelectrochemical stimulation imposed a selective pressure on the microbial community of anodes, including that far from the cathode. These results suggested that sand amendment can be an effective approach for soil conditioning that will enhances the bioelectrochemical removal of hydrocarbons in contaminated soils. Copyright © 2015 Elsevier Ltd. All rights reserved.

Isolation and Characterization of Hydrocarbon-Degrading Yeast Strains from Petroleum Contaminated Industrial Wastewater

Science.gov (United States)

Gargouri, Boutheina; Mhiri, Najla; Karray, Fatma; Aloui, Fathi; Sayadi, Sami

2015-01-01

Two yeast strains are enriched and isolated from industrial refinery wastewater. These strains were observed for their ability to utilize several classes of petroleum hydrocarbons substrates, such as n-alkanes and aromatic hydrocarbons as a sole carbon source. Phylogenetic analysis based on the D1/D2 variable domain and the ITS-region sequences indicated that strains HC1 and HC4 were members of the genera Candida and Trichosporon, respectively. The mechanism of hydrocarbon uptaking by yeast, Candida, and Trichosporon has been studied by means of the kinetic analysis of hydrocarbons-degrading yeasts growth and substrate assimilation. Biodegradation capacity and biomass quantity were daily measured during twelve days by gravimetric analysis and gas chromatography coupled with mass spectrometry techniques. Removal of n-alkanes indicated a strong ability of hydrocarbon biodegradation by the isolated yeast strains. These two strains grew on long-chain n-alkane, diesel oil, and crude oil but failed to grow on short-chain n-alkane and aromatic hydrocarbons. Growth measurement attributes of the isolates, using n-hexadecane, diesel oil, and crude oil as substrates, showed that strain HC1 had better degradation for hydrocarbon substrates than strain HC4. In conclusion, these yeast strains can be useful for the bioremediation process and decreasing petroleum pollution in wastewater contaminated with petroleum hydrocarbons. PMID:26339653

Isolation and Characterization of Hydrocarbon-Degrading Yeast Strains from Petroleum Contaminated Industrial Wastewater

Directory of Open Access Journals (Sweden)

Boutheina Gargouri

2015-01-01

Full Text Available Two yeast strains are enriched and isolated from industrial refinery wastewater. These strains were observed for their ability to utilize several classes of petroleum hydrocarbons substrates, such as n-alkanes and aromatic hydrocarbons as a sole carbon source. Phylogenetic analysis based on the D1/D2 variable domain and the ITS-region sequences indicated that strains HC1 and HC4 were members of the genera Candida and Trichosporon, respectively. The mechanism of hydrocarbon uptaking by yeast, Candida, and Trichosporon has been studied by means of the kinetic analysis of hydrocarbons-degrading yeasts growth and substrate assimilation. Biodegradation capacity and biomass quantity were daily measured during twelve days by gravimetric analysis and gas chromatography coupled with mass spectrometry techniques. Removal of n-alkanes indicated a strong ability of hydrocarbon biodegradation by the isolated yeast strains. These two strains grew on long-chain n-alkane, diesel oil, and crude oil but failed to grow on short-chain n-alkane and aromatic hydrocarbons. Growth measurement attributes of the isolates, using n-hexadecane, diesel oil, and crude oil as substrates, showed that strain HC1 had better degradation for hydrocarbon substrates than strain HC4. In conclusion, these yeast strains can be useful for the bioremediation process and decreasing petroleum pollution in wastewater contaminated with petroleum hydrocarbons.

Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

Energy Technology Data Exchange (ETDEWEB)

Tellez, G.; Khandan, N.

1995-12-31

The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l; and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.

Biodegradation and chemical characterization of petroleum diesel hydrocarbons in seawater at low temperatures

OpenAIRE

Bausch, Alexandre Renee

2010-01-01

Master's thesis in Environmental engineering Petroleum hydrocarbons are a major source of marine contamination. Biodegradation, which is fundamental for the natural attenuation of these hydrocarbons in nature, involves mineralization or transformation of organic compounds by autochthonous microorganism communities. Various limiting factors characteristic of the petroleum, the external environment, and the microbial community determine the fate of oil (e.g., diesel) in the marine environmen...

Petroleum Hydrocarbons Contamination Profile of Ochani Stream in ...

African Journals Online (AJOL)

Petroleum hydrocarbon contamination profile, heavy metals and some physicochemical parameters were investigated in Ochani Stream site in Ejamah Ebubu, Eleme Local Government Area of Rivers State. The results show that a major crude oil spillage occurred at Ejamah Ebubu, Rivers State, Nigeria approximately 30 ...

Petroleum hydrocarbon toxicity to corals: A review.

Science.gov (United States)

Turner, Nicholas R; Renegar, D Abigail

2017-06-30

The proximity of coral reefs to coastal urban areas and shipping lanes predisposes corals to petroleum pollution from multiple sources. Previous research has evaluated petroleum toxicity to coral using a variety of methodology, including monitoring effects of acute and chronic spills, in situ exposures, and ex situ exposures with both adult and larval stage corals. Variability in toxicant, bioassay conditions, species and other methodological disparities between studies prevents comprehensive conclusions regarding the toxicity of hydrocarbons to corals. Following standardized protocols and quantifying the concentration and composition of toxicant will aid in comparison of results between studies and extrapolation to actual spills. Copyright © 2017 Elsevier Ltd. All rights reserved.

Monitoring of ground water quality and heavy metals in soil during large scale bioremediation of petroleum hydrocarbon contaminated waste in India: case studies

Directory of Open Access Journals (Sweden)

Ajoy Kumar Mandal

2014-10-01

Full Text Available Bioremediation using microbes has been well accepted as an environmentally friendly and economical treatment method for disposal of hazardous petroleum hydrocarbon contaminated waste (oily waste and this type of bioremediation has been successfully conducted in laboratory and on a pilot scale in various countries, including India. Presently there are no federal regulatory guidelines available in India for carrying out field-scale bioremediation of oily waste using microbes. The results of the present study describe the analysis of ground water quality as well as selected heavy metals in oily waste in some of the large-scale field case studies on bioremediation of oily waste (solid waste carried out at various oil installations in India. The results show that there was no contribution of oil and grease and selected heavy metals to the ground water in the nearby area due to adoption of this bioremediation process. The results further reveal that there were no changes in pH and EC of the groundwater due to bioremediation. In almost all cases the selected heavy metals in residual oily waste were within the permissible limits as per Schedule – II of Hazardous Waste Management, Handling and Transboundary Movement Act, Amendment 2008, (HWM Act 2008, by the Ministry of Environment and Forests (MoEF, Government of India (GoI.

Current developments in the assessment of petroleum hydrocarbon contaminated sites: Analysis, interpretation, and use of the TPH parameter for quantitative risk assessment

International Nuclear Information System (INIS)

Garcia-Surette, M.; Maynard, P.; Lamie, P.O.; Kaslick, C.

1995-01-01

In 1994, the Massachusetts Department of Environmental Protection (MDEP) estimated that petroleum-only cases comprised approximately one-half of the state's hazardous waste sites currently under investigation and/or remediation. Because of this significant percentage, it became clear that assessing petroleum sites more efficiently in terms of risk and cleanup alternatives was necessary. One of these key MDEP policies describes an alternative risk assessment approach enabling the quantitative characterization of total petroleum hydrocarbon (TPH)-related health risks. The approach relies on the use of an analytical technique by which the mass of petroleum hydrocarbons within specified carbon ranges is quantified. MDEP's TPH risk assessment approach was successfully employed at a residential site contaminated with No. 2 fuel oil. The combined use of MDEP's suggested analytical methods, alternative reference compounds and toxicity values, as well as chromatograms, standard dose equations, and an EPA-approved box model, facilitated the performance of a more realistic and cost-effective assessment of risk. Such assessment provided key management information to regulatory agencies, and project managers, as well as property owners concerned with potential property value loss

Pilot-scale feasibility of petroleum hydrocarbon-contaminated soil in situ bioremediation

International Nuclear Information System (INIS)

Walker, J.F. Jr.; Walker, A.B.

1995-01-01

An environmental project was conducted to evaluate in situ bioremediation of petroleum hydrocarbon-contaminated soils on Kwajalein Island, a US Army Kwajalein Atoll base in the Republic of the Marshall Islands. Results of laboratory column studies determined that nutrient loadings stimulated biodegradation rates and that bioremediation of hydrocarbon-contaminated soils at Kwajalein was possible using indigenous microbes. The column studies were followed by an ∼10-month on-site demonstration at Kwajalein to further evaluate in situ bioremediation and to determine design and operating conditions necessary to optimize the process. The demonstration site contained low levels of total petroleum hydrocarbons (diesel fuel) in the soil near the ground surface, with concentrations increasing to ∼10,000 mg/kg in the soil near the groundwater. The demonstration utilized 12 in situ plots to evaluate the effects of various combinations of water, air, and nutrient additions on both the microbial population and the hydrocarbon concentration within the treatment plots as a function of depth from the ground surface

Petroleum hydrocarbons in intertidal ecosystem along the Bombay Coast

Digital Repository Service at National Institute of Oceanography (India)

Ingole, S.A.; Kadam, A.N.; Mayadeo, M.S.; Dhadke, P.M.

of petroleum hydrocarbons (153.8 mu g.l sup(-1) in water sample collected near an outfall indicated that the intertidal ecosystem of Worli might be contaminated by the effluent discharges from the onshore industrial unit...

Microbial activity and soil organic matter decay in roadside soils polluted with petroleum hydrocarbons

Science.gov (United States)

Mykhailova, Larysa; Fischer, Thomas; Iurchenko, Valentina

2015-04-01

It has been demonstrated previously that hydrocarbon addition to soil provokes soil organic matter priming (Zyakun et al., 2011). It has further been shown that petroleum hydrocarbons deposit to roadside soils bound to fine mineral particles and together with vehicle spray (Mykhailova et al., 2014), and that hydrocarbon concentrations decrease to safe levels within the first 15 m from the road, reaching background concentrations at 60-100 m distance (Mykhailova et al., 2013). It was the aim of this study to (I) identify the bioavailability of different petroleum hydrocarbon fractions to degradation and to (II) identify the native (i.e. pedogenic) C fraction affected by hydrocarbon-mediated soil organic matter priming during decay. To address this aim, we collected soil samples at distances from 1 to 100 m (sampling depth 15 cm) near the Traktorostroiteley avenue and the Pushkinskaya street in Kharkov, as well as near the country road M18 near Kharkov, Ukraine. The roads have been under exploitation for several decades, so microbial adaptation to enhanced hydrocarbon levels and full expression of effects could be assumed. The following C fractions were quantified using 13C-CP/MAS-NMR: Carbohydrates, Proteins, Lignin, Aliphates, Carbonyl/Carboxyl as well as black carbon according to Nelson and Baldock (2005). Petroleum hydrocarbons were determind after hexane extraction using GC-MS and divided into a light fraction (chain-length C27, Mykhailova et al., 2013). Potential soil respiration was determined every 48 h by trapping of CO2 evolving from 20 g soil in NaOH at 20 ° C and at 60% of the maximum water holding capacity and titration after a total incubation period of 4 weeks in the lab. It was found that soil respiration positively correlated with the ratio of the light fraction to the sum of medium and heavy fractions of petroleum hydrocarbons, which indicates higher biodegradation primarily of the light petroleum hydrocarbon fraction. Further, soil respiration was

Petroleum hydrocarbon concentration in surface sediments in continental shelf region along the central west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Ram, A.; Kadam, A.N.

Gas chromatography revealed that nonpolar material extracted from surface sediments collected along the northern west coast of India was originated from petroleum hydrocarbon residue. Petroleum hydrocarbon levels as determinEd. by fluorescence...

Total petroleum hydrocarbons: Characterization of physico-chemical behaviour and risks

Energy Technology Data Exchange (ETDEWEB)

Gemoets, J.; Lookman, R.; Vanermen, G.; Houtven, D. van; Bertels, D.; Weltens, R.; Cornelis, C. [VITO, Mol (Belgium); Vries, P. de; Sterren, G. van der; Alphenaar, A. [TTE, Deventer (Netherlands)

2003-07-01

Several methods are available for the characterization of petroleum hydrocarbons. Recently, the TPHCWG (Total Petroleum Hydrocarbon Criteria Working Group) developed a method based upon a silica column separation of aromatics and aliphatics and a GC-FID subdivision into equivalent-carbon fractions (EC) ('TPH-method'). Within NOBIS (Dutch Research program Biological I-situ Remediation), another method was developed based upon an equilibrium-experiment of the oil-polluted soil with water (column recirculation), which was further developed by TTE ('TTE-method'). This method uses measured water solubilities of individual oil components and GC-retention times yielding a subdivision of the hydrocarbons into compound classes. The present study aims at a verification (reproducibility; accuracy) and optimization of both methods and a critical review on the relevance of the proposed fractions for the prediction of human health risks. Two 'umpire' methods were selected for reference: GS-MS in full scan mode and liquid state NMR. (orig.)

Interpreting residues of petroleum hydrocarbons in wildlife tissues

International Nuclear Information System (INIS)

Hall, R.J.; Coon, N.C.

1988-08-01

This report is the first publication in the field of environmental-contaminant effects on wildlife to tell the reader how to interpret the results of analytical chemical results. Specifically, the publication describes how to interpret residues of petroleum hydrocarbons in wildlife tissues. Pollutant oil residues in avian species are emphasized

Bioremediation of petroleum hydrocarbon contaminated soils using soil vapor extraction: Case study

International Nuclear Information System (INIS)

Roth, R.J.; Peterson, R.M.

1994-01-01

Soils contaminated with petroleum hydrocarbons are being remediated in situ at a site in Lakewood, New Jersey by bioremediation in conjunction with soil vapor extractions (SVE) and nutrient addition. The contaminants were from hydraulic oils which leaked from subsurface hydraulic lifts, waste oil from leaking underground storage tanks (USTs), an aboveground storage tank, and motor oil from a leaking UST. The oils contaminated subsurface soils at the site to a depth of 25 feet. Approximately 900 cubic yards of soil were contaminated. Soil sample analyses showed total petroleum hydrocarbon (TPH) concentrations up to 31,500 ppm. The design of the remedial system utilized the results of a treatability study which showed that TPH degrading microorganisms, when supplied with oxygen and nutrients, affected a 14% reduction in TPH in 30 days. A SVE system was installed which used three wells, each installed to a depth of 25 feet below grade. The SVE system was operated to achieve an extracted air flow of approximately 20 to 30 scfm from each well. Bioremediation of the TPH was monitored by measuring CO 2 and O 2 concentrations at the wellheads and vapor monitoring probes. After four months of remediation, CO 2 concentrations were at a minimum, at which point the subsurface soils were sampled and analyzed for TPH. The soil analyses showed a removal of TPH by biodegradation of up to 99.8% after four months of remediation

A new biodegradation prediction model specific to petroleum hydrocarbons.

Science.gov (United States)

Howard, Philip; Meylan, William; Aronson, Dallas; Stiteler, William; Tunkel, Jay; Comber, Michael; Parkerton, Thomas F

2005-08-01

A new predictive model for determining quantitative primary biodegradation half-lives of individual petroleum hydrocarbons has been developed. This model uses a fragment-based approach similar to that of several other biodegradation models, such as those within the Biodegradation Probability Program (BIOWIN) estimation program. In the present study, a half-life in days is estimated using multiple linear regression against counts of 31 distinct molecular fragments. The model was developed using a data set consisting of 175 compounds with environmentally relevant experimental data that was divided into training and validation sets. The original fragments from the Ministry of International Trade and Industry BIOWIN model were used initially as structural descriptors and additional fragments were then added to better describe the ring systems found in petroleum hydrocarbons and to adjust for nonlinearity within the experimental data. The training and validation sets had r2 values of 0.91 and 0.81, respectively.

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

International Nuclear Information System (INIS)

Akbari, Ali; Ghoshal, Subhasis

2014-01-01

Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day −1 in biopile tank compared to 0.11 day −1 in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction were

Efficiency of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from contaminated soil.

Science.gov (United States)

Singh, Anil Kumar; Cameotra, Swaranjit Singh

2013-10-01

This study describes the potential application of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from the soil samples collected from industrial dumping site. High concentrations of heavy metals (like iron, lead, nickel, cadmium, copper, cobalt and zinc) and petroleum hydrocarbons were present in the contaminated soil samples. Lipopeptide biosurfactant, consisting of surfactin and fengycin was obtained from Bacillus subtilis A21. Soil washing with biosurfactant solution removed significant amount of petroleum hydrocarbon (64.5 %) and metals namely cadmium (44.2 %), cobalt (35.4 %), lead (40.3 %), nickel (32.2 %), copper (26.2 %) and zinc (32.07 %). Parameters like surfactant concentration, temperature, agitation condition and pH of the washing solution influenced the pollutant removing ability of biosurfactant mixture. Biosurfactant exhibited substantial hydrocarbon solubility above its critical micelle concentration. During washing, 50 % of biosurfactant was sorbed to the soil particles decreasing effective concentration during washing process. Biosurfactant washed soil exhibited 100 % mustard seed germination contradictory to water washed soil where no germination was observed. The results indicate that the soil washing with mixture of lipopeptide biosurfactants at concentrations above its critical micelle concentration can be an efficient and environment friendly approach for removing pollutants (petroleum hydrocarbon and heavy metals) from contaminated soil.

Fate of petroleum hydrocarbons and toxic organics in Louisiana coastal environments

International Nuclear Information System (INIS)

DeLaune, R.D.; Gambrell, R.P.; Pardue, J.H.; Patrick, W.H. Jr.

1991-01-01

Numerous potentially toxic compounds are entering Louisiana's inshore and nearshore coastal environments. To a large degree there is insufficient information for predicting the fate and effect of these materials in aquatic environments. Studies documenting the impact of petroleum hydrocarbons entering Louisiana coastal wetlands are summarized. Also included are research findings on factors affecting the persistence of petroleum hydrocarbons and other toxic organics (pentachlorophenol (PCP), 2,4-dichlorophenoxyacetic acid (2,4-D), creosote, etc.) in sediment-water systems. Sediment pH and redox conditions have been found to play an important role in the microbial degradation of toxic organics. Most of the hydrocarbons investigated degrade more rapidly under high redox (aerobic) conditions although there are exceptions (e.g., 1,1,1-trichloro-2,2-bis(4-chlorophenyl)(DDT) and polychlorobiphenyls (PCBs)). Some of these compounds, due to their slow degradation in anaerobic sediment, may persist in the system for decades

Combination of biochar amendment and phytoremediation for hydrocarbon removal in petroleum-contaminated soil.

Science.gov (United States)

Han, Tao; Zhao, Zhipeng; Bartlam, Mark; Wang, Yingying

2016-11-01

Remediation of soils contaminated with petroleum is a challenging task. Four different bioremediation strategies, including natural attenuation, biochar amendment, phytoremediation with ryegrass, and a combination of biochar and ryegrass, were investigated with greenhouse pot experiments over a 90-day period. The results showed that planting ryegrass in soil can significantly improve the removal rate of total petroleum hydrocarbons (TPHs) and the number of microorganisms. Within TPHs, the removal rate of total n-alkanes (45.83 %) was higher than that of polycyclic aromatic hydrocarbons (30.34 %). The amendment of biochar did not result in significant improvement of TPH removal. In contrast, it showed a clear negative impact on the growth of ryegrass and the removal of TPHs by ryegrass. The removal rate of TPHs was significantly lower after the amendment of biochar. The results indicated that planting ryegrass is an effective remediation strategy, while the amendment of biochar may not be suitable for the phytoremediation of soil contaminated with petroleum hydrocarbons.

Degradation of Total Petroleum Hydrocarbon and BTEX Compounds in Produced Water

Energy Technology Data Exchange (ETDEWEB)

Jackson, Lorri

2002-04-01

Petroleum Environmental Technologies, LLC entered into a Cooperative Research and Development agreement with the Rocky Mountain Oilfield Testing Center to an in-situ pit treatment demonstration and produced water treatment demonstration. The purpose of the test is to demonstrate the degradation of petroleum hydrocarbon compounds in soil and aqueous matrices where ECOSAFE is applied to enhance the degradation of these contaminants.

Abiogenic origin of petroleum hydrocarbons: Need to rethink exploration strategies

Digital Repository Service at National Institute of Oceanography (India)

Paropkari, A.L.

-depletion of petroleum deposits since long. Considering these strong evidences, it is suggested to explore the onshore and offshore regions characterized by faults, gas escape features, mud diapirs and mud volcanoes for detailed abiogenic hydrocarbon exploration...

Bioremediation of soils containing petroleum hydrocarbons, chlorinated phenols, and polycyclic aromatic hydrocarbons

International Nuclear Information System (INIS)

Seech, A.; Burwell, S.; Marvan, I.

1994-01-01

Bench-scale treatability investigations, pilot-scale and full-scale bioremediation projects were conducted to evaluate Daramend trademark bioremediation of soils containing petroleum hydrocarbons, heavy oils, paraffins, chlorinated phenols and polycyclic aromatic hydrocarbons (PAHs). Bench-scale investigations were conducted using glass microcosms. Pilot-scale and full-scale demonstrations were conducted at industrial sites and included treatment of excavated soils and sediments in on-site cells constructed using synthetic liners and covered by steel/polyethylene structures as well as in-situ treatment. A total of approximately 5,000 tons of soil was treated. The soil treatment included organic soil amendments, specialized tillage/aeration apparatus, and strict control of soil moisture. The amendments are composed of naturally-occurring organic materials prepared to soil-specific particle size distributions, nutrient profiles, and nutrient-release kinetics. Bench-scale work indicated that in refinery soil containing high concentrations of heavy oils, extractable hydrocarbon concentrations could be rapidly reduced to industrial clean-up criteria, and that the hydrocarbons were fully mineralized with release of CO 2

Total petroleum hydrocarbons in sediments from the coastline and mangroves of the northern Persian Gulf.

Science.gov (United States)

Mohebbi-Nozar, Seyedeh Laili; Zakaria, Mohamad Pauzi; Ismail, Wan Ruslan; Mortazawi, Mohammad Seddiq; Salimizadeh, Maryam; Momeni, Mohammad; Akbarzadeh, Gholamali

2015-06-15

To provide baseline information for the marine ecosystem of Hormozgan province, the distribution of petroleum hydrocarbons was evaluated in 52 stations involved in the mangrove and coastline ecosystem. Coastline sampling sites included areas facing harbor, river, domestic and industrial discharge. Sediment samples were analyzed based on ultraviolet fluorescence spectroscopy. Petroleum hydrocarbons showed narrow variations ranging from non-detectable (ND) to 1.71 and from 0.2 to 0.63μg/g dry weight for coastline and mangrove sediments, respectively. The detected concentrations for total petroleum hydrocarbons were lower than guideline values for ecological risk. Furthermore, the minimum environmental risk was confirmed by background levels for the Persian Gulf, the Sea of Oman, and detected values for reference areas. The results were regarded as background data in the studied area, and, considering the rapid expansion of activities related to the petroleum industry in Hormozgan province, the continuous monitoring of pollutants is recommended. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fate and effects of petroleum hydrocarbons in marine coastal ecosystems

International Nuclear Information System (INIS)

Vanderhorst, J.R.

1977-01-01

Preliminary results are reported from field and laboratory studies on the effects of petroleum hydrocarbons on marine organisms of Northwest Pacific coastal ecosystems. Chemical methods for the characterization of test solutions for specific hydrocarbons (benzene, toluene, xylene, and heptodecane) were developed concurrently with population and community studies of the effects of short-term and chronic exposures. Results are reported from studies on algae (Ulva), clams (protothaca staminea), crustaceans (Anomyx and Neomysis) and burrowing worms

Bioremediation and reclamation of soil contaminated with petroleum oil hydrocarbons by exogenously seeded bacterial consortium: a pilot-scale study.

Science.gov (United States)

Mukherjee, Ashis K; Bordoloi, Naba K

2011-03-01

Spillage of petroleum hydrocarbons causes significant environmental pollution. Bioremediation is an effective process to remediate petroleum oil contaminant from the ecosystem. The aim of the present study was to reclaim a petroleum oil-contaminated soil which was unsuitable for the cultivation of crop plants by using petroleum oil hydrocarbon-degrading microbial consortium. Bacterial consortium consisting of Bacillus subtilis DM-04 and Pseudomonas aeruginosa M and NM strains were seeded to 20% (v/w) petroleum oil-contaminated soil, and bioremediation experiment was carried out for 180 days under laboratory condition. The kinetics of hydrocarbon degradation was analyzed using biochemical and gas chromatographic (GC) techniques. The ecotoxicity of the elutriates obtained from petroleum oil-contaminated soil before and post-treatment with microbial consortium was tested on germination and growth of Bengal gram (Cicer aretinum) and green gram (Phaseolus mungo) seeds. Bacterial consortium showed a significant reduction in total petroleum hydrocarbon level in contaminated soil (76% degradation) as compared to the control soil (3.6% degradation) 180 days post-inoculation. The GC analysis confirmed that bacterial consortium was more effective in degrading the alkane fraction compared to aromatic fraction of crude petroleum oil hydrocarbons in soil. The nitrogen, sulfur, and oxygen compounds fraction was least degraded. The reclaimed soil supported the germination and growth of crop plants (C. aretinum and P. mungo). In contrast, seeds could not be germinated in petroleum oil-contaminated soil. The present study reinforces the application of bacterial consortium rather than individual bacterium for the effective bioremediation and reclamation of soil contaminated with petroleum oil.

Toxicology of oil field wastes. Hazards to livestock associated with the petroleum industry.

Science.gov (United States)

Edwards, W C

1989-07-01

In oil-producing states, the proximity of livestock to drilling operations and production sites often results in poisoning of animals from ingestion of crude oil, condensate, salt water, heavy metals, and caustic chemicals. The heavy metals encountered most frequently are lead from pipe joint compound and arsenicals and chromates used as corrosion inhibitors. Numerous toxic and caustic chemicals are used in drilling muds and fluids. Crude oil and salt water spills are common occurrences around production sites. Pipeline breaks may result in exposure of livestock to crude oil or refined petroleum hydrocarbons. Ingestion of petroleum hydrocarbons may result in sudden death from peracute bloat. The most common cause of illness or death following exposure to petroleum hydrocarbons is aspiration pneumonia, which may cause a chronic progressive deterioration of health, with death after several days or weeks. Cases in which livestock are exposed to oil, salt water, or caustic chemicals, but do not die acutely or from aspiration pneumonia are more frustrating to diagnose. In these cases, parasitism, poor nutrition, and other debilitating diseases must be considered. Anorexia, weight loss, and decreased rumen motility may be caused by a disruption of normal rumen function. Petroleum hydrocarbons, salt water, and caustic chemicals have the potential of altering rumen flora and enzymatic processes as well as damaging the ruminal and gastrointestinal epithelium. The toxicity of petroleum hydrocarbons appears to be related more closely to the volatility and viscosity of the product than to other factors. The more volatile straight chain and aromatic petroleum hydrocarbons have a greater potential for aspiration pneumonia and may produce an anesthetic-like action if absorbed systemically. The more volatile petroleum hydrocarbons also are more irritating to skin and mucous membranes and appear to be more damaging to rumen flora. Treatment of petroleum hydrocarbon ingestion is

Applying petroleum biomarkers as a tool for confirmation of petroleum hydrocarbons in high organic content soils

Energy Technology Data Exchange (ETDEWEB)

O' Sullivan, G.; Martin, E.J.; Waddell, J.; Sandau, C.D. [TRIUM Environmental Solutions, Cochrane, AB (Canada); Denham, G. [Nexen Inc., Calgary, AB (Canada); Samis, M.W. [Great Plains Environmental Management Ltd., Medecine Hat, AB (Canada)

2009-10-01

It is often difficult to separate naturally occurring phytogenic organic materials from petrogenic sources in routine gas chromatography flame ionization detection (GC-FID) analyses. Phytogenic compounds include tannins, waxes, terpenes, fats and oils. This study examined the use of petroleum biomarkers as a means of determining the nature, sources, type and geological conditions of the formation of petroleum hydrocarbons (PHCs). The analysis was conducted at a former well site consisting of low-lying peat marshlands that had the potential to interfere with the delineation of PHC impacts. Fourteen boreholes and 8 hand auger holes were placed at the site. Soil samples were analyzed for salinity, metals, and PHC constituents. Biomarker targets included acyclic isoprenoid compounds, polycyclic aromatic hydrocarbon (PAH) compounds, terpanes, hopanes, and triaromatic steranes. A grain-size analysis showed the presence of peat materials within the saturated zone. Results of the study demonstrated the presence of PHC constituents that exceeded applicable guidelines. The biomarker analysis was used to statistically determine site-specific background levels of hydrocarbons. Nearly 3000 tonnes of soil were excavated from the site. It was concluded that site-specific conditions should be taken into consideration when evaluating reclamation targets. 3 refs., 6 figs.

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

Energy Technology Data Exchange (ETDEWEB)

Akbari, Ali; Ghoshal, Subhasis, E-mail: subhasis.ghoshal@mcgill.ca

2014-09-15

Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day{sup −1} in biopile tank compared to 0.11 day{sup −1} in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction

[Compositions and residual properties of petroleum hydrocarbon in contaminated soil of the oilfields].

Science.gov (United States)

Hu, Di; Li, Chuan; Dong, Qian-Qian; Li, Li-Ming; Li, Guang-He

2014-01-01

The aims of this study were to determine the compositions and residual properties of petroleum hydrocarbon in soil, as well as to identify the source and weathering degree of the pollution. A total of 5 producing wells in Gudao and Hekou oil producing region of Shengli oilfields were analyzed. More than 50 individual target compounds including straight-and branched-chain alkanes( n-alkanes, pristine and phytane) and polycyclic aromatic hydrocarbons (PAHs) in soil samples and crude oil were determined by gas chromatography-mass spectrometry (GC-MS). The percentages of chain alkanes and PAHs in total solvent extractable matters(TSEM) of soil samples were both much lower than those in the crude oil samples. The compositions of petroleum hydrocarbon in soil samples differed from those in crude oil, which indicated the n-alkanes with carbon numbers contaminated soils, the relationship between the index and petroleum hydrocarbon compounds was analyzed using principal component analysis (PCA). The results showed that the n-alkanes with carbon numbers > 33 and the PAHs with rings between 3 and 5 were much harder to degrade. PCA of 4 indexes for source identification revealed more than 50% of the soil samples were polluted by crude oil, which needs more attention during remediation.

Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site.

Science.gov (United States)

Akbari, Ali; Ghoshal, Subhasis

2014-09-15

Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16-C34) in a pilot-scale biopile experiment conducted at 15°C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16-C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day(-1) in biopile tank compared to 0.11 day(-1) in slurry bioreactors for C16-C34 hydrocarbons, the biodegradation extents for this fraction were comparable in these two systems. Copyright © 2014 Elsevier B.V. All rights reserved.

International petroleum enviromental conference (IPEC) offers opportunity for exchange of ideas

International Nuclear Information System (INIS)

Veil, J.A.; Spiric, Z.

2001-01-01

Oil and gas are produced in many parts of the world. Persons working in the petroleum industry can learn much by communicating with colleagues in other countries, but the opportunities for engineers and scientists to come together and discuss petroleum environmental control practices, technologies, and regulations with representatives of other countries are limited. This paper describes the very useful International Petroleum Environmental Conference (IPEC) which completed its seventh meeting in November 2000 in Albuquerque, New Mexico, USA. The 7th IPEC attracted 350 participants, including 26 participants from countries other than the United States. The 7th IPEC emphasized international issues and included more than 20 papers by international authors or on international topics. The conference covered all aspects of petroleum environmental issues and featured speakers from many disciplines. The conference included technical sessions on the following topics: Legal and Regulatory Issues in the Oil and Gas Industry; Pollution Prevention, Waste Management, and Waste Minimization; Bioremediation of Petroleum Hydrocarbons; Characterization and Remediation of Brine-Impacted Soils; Biotreatment and Bioremediation; International Issues in the Oil and Gas Industry; Phytoremediation of Petroleum Hydrocarbons; Treatment and Management of Produced Water; Forensic Geochemistry and Site Characterization/Technology Transfer; Environmentall Acceptable Endpoints; Desulfurization of Fuels and Waste Streams; Control of Air Emissions; MTBE/Phytoremediation and Natural Attenuation; and Treatment and Remediation of Petroleum Hydrocarbons. The last day of the conference was devoted to a special symposium on 'Innovative Technologies for Subsurface Characterization and Remediation.' The authors recommend this conference as a forum for industry, government, and academia to freely exchange ideas and information

40 CFR 268.35 - Waste specific prohibitions-petroleum refining wastes.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Waste specific prohibitions-petroleum refining wastes. 268.35 Section 268.35 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... generator may use knowledge of the waste. If the waste contains constituents in excess of the applicable...

Influence of soil and hydrocarbon properties on the solvent extraction of high-concentration weathered petroleum from contaminated soils.

Science.gov (United States)

Sui, Hong; Hua, Zhengtao; Li, Xingang; Li, Hong; Wu, Guozhong

2014-05-01

Petroleum ether was used to extract petroleum hydrocarbons from soils collected from six oil fields with different history of exploratory and contamination. It was capable of fast removing 76-94 % of the total petroleum hydrocarbons including 25 alkanes (C11-C35) and 16 US EPA priority polycyclic aromatic hydrocarbons from soils at room temperature. The partial least squares analysis indicated that the solvent extraction efficiencies were positively correlated with soil organic matter, cation exchange capacity, moisture, pH, and sand content of soils, while negative effects were observed in the properties reflecting the molecular size (e.g., molecular weight and number of carbon atoms) and hydrophobicity (e.g., water solubility, octanol-water partition coefficient, soil organic carbon partition coefficient) of hydrocarbons. The high concentration of weathered crude oil at the order of 10(5) mg kg(-1) in this study was demonstrated adverse for solvent extraction by providing an obvious nonaqueous phase liquid phase for hydrocarbon sinking and increasing the sequestration of soluble hydrocarbons in the insoluble oil fractions during weathering. A full picture of the mass distribution and transport mechanism of petroleum contaminants in soils will ultimately require a variety of studies to gain insights into the dynamic interactions between environmental indicator hydrocarbons and their host oil matrix.

Prediction of Petroleum Hydrocarbon Bioavailability in Contaminated Soils and Sediments

NARCIS (Netherlands)

Cuypers, M.P.; Clemens, R.; Grotenhuis, J.T.C.; Rulkens, W.H.

2001-01-01

Recently, several laboratory methods have been developed for the prediction of contaminant bioavailability. So far, none of these methods has been extensively tested for petroleum hydrocarbons. In the present study we investigated solid-phase extraction and persulfate oxidation for the prediction of

Biofuel components change the ecology of bacterial volatile petroleum hydrocarbon degradation in aerobic sandy soil

International Nuclear Information System (INIS)

Elazhari-Ali, Abdulmagid; Singh, Arvind K.; Davenport, Russell J.; Head, Ian M.; Werner, David

2013-01-01

We tested the hypothesis that the biodegradation of volatile petroleum hydrocarbons (VPHs) in aerobic sandy soil is affected by the blending with 10 percent ethanol (E10) or 20 percent biodiesel (B20). When inorganic nutrients were scarce, competition between biofuel and VPH degraders temporarily slowed monoaromatic hydrocarbon degradation. Ethanol had a bigger impact than biodiesel, reflecting the relative ease of ethanol compared to methyl ester biodegradation. Denaturing gradient gel electrophoresis (DGGE) of bacterial 16S rRNA genes revealed that each fuel mixture selected for a distinct bacterial community, each dominated by Pseudomonas spp. Despite lasting impacts on soil bacterial ecology, the overall effects on VHP biodegradation were minor, and average biomass yields were comparable between fuel types, ranging from 0.40 ± 0.16 to 0.51 ± 0.22 g of biomass carbon per gram of fuel carbon degraded. Inorganic nutrient availability had a greater impact on petroleum hydrocarbon biodegradation than fuel composition. Highlights: ► The effect of 10% ethanol or 20% biodiesel on the biodegradability of volatile petroleum hydrocarbons in soil was investigated. ► Competition for scarce inorganic nutrients between biofuel and VPH degraders slowed monoaromatic hydrocarbon degradation. ► Biofuel effects were transitional. ► Each fuel selected for a distinct predominant bacterial community. ► All bacterial communities were dominated by Pseudomonas spp. - Blending of petroleum with ethanol or biodiesel changes the fuel degrading soil bacterial community structure, but the long-term effects on fuel biodegradability are minor.

Valorization of Waste Lipids through Hydrothermal Catalytic Conversion to Liquid Hydrocarbon Fuels with in Situ Hydrogen Production

Energy Technology Data Exchange (ETDEWEB)

Kim, Dongwook; Vardon, Derek R.; Murali, Dheeptha; Sharma, Brajendra K.; Strathmann, Timothy J.

2016-03-07

We demonstrate hydrothermal (300 degrees C, 10 MPa) catalytic conversion of real waste lipids (e.g., waste vegetable oil, sewer trap grease) to liquid hydrocarbon fuels without net need for external chemical inputs (e.g., H2 gas, methanol). A supported bimetallic catalyst (Pt-Re/C; 5 wt % of each metal) previously shown to catalyze both aqueous phase reforming of glycerol (a triacylglyceride lipid hydrolysis coproduct) to H2 gas and conversion of oleic and stearic acid, model unsaturated and saturated fatty acids, to linear alkanes was applied to process real waste lipid feedstocks in water. For reactions conducted with an initially inert headspace gas (N2), waste vegetable oil (WVO) was fully converted into linear hydrocarbons (C15-C17) and other hydrolyzed byproducts within 4.5 h, and H2 gas production was observed. Addition of H2 to the initial reactor headspace accelerated conversion, but net H2 production was still observed, in agreement with results obtained for aqueous mixtures containing model fatty acids and glycerol. Conversion to liquid hydrocarbons with net H2 production was also observed for a range of other waste lipid feedstocks (animal fat residuals, sewer trap grease, dry distiller's grain oil, coffee oil residual). These findings demonstrate potential for valorization of waste lipids through conversion to hydrocarbons that are more compatible with current petroleum-based liquid fuels than the biodiesel and biogas products of conventional waste lipid processing technologies.

Petroleum Hydrocarbon Profiles of Water and Sediment of Algoa Bay, Eastern Cape, South Africa

Directory of Open Access Journals (Sweden)

Abiodun O. Adeniji

2017-10-01

Full Text Available Petroleum hydrocarbon profiles of water and sediment samples of Algoa Bay in the Eastern Cape Province of South Africa were assessed using standard analytical procedures. Water (from surface and bottom levels and sediment samples were collected from five locations in the bay from February to June 2016. Extraction of the petroleum hydrocarbons from the water and sediment samples collected was achieved using liquid-liquid and Soxhlet extraction techniques, respectively, followed by column clean up. Target compounds were analytically determined with gas chromatography–flame ionization detector (GC-FID and quantified by integrating the areas of both the resolved and unresolved components. Physicochemical properties of the water samples were also determined on site using a SeaBird 19plusV2 CTD SBE 55 device. Estimated limit of detection, limit of quantitation and relative standard deviation for the 35 n-alkane standards ranged from 0.06 to 0.13 μg/L, 0.30 to 0.69 μg/L and 3.61 to 8.32%, respectively. Results showed that total petroleum hydrocarbon (TPH varied from 45.07 to 307 μg/L in the water and 0.72 to 27.03 mg/kg in the sediments. The mean concentrations of TPH in both the water and sediment samples from Algoa Bay revealed a slight level of pollution. The diagnostic indices used showed that the hydrocarbons in the area were from both biogenic and anthropogenic sources. Hence, there is need for adequate regulation and control of all activities contributing to the levels of petroleum hydrocarbon in the marine environment for the safety of human, aquatic and wild lives in the area.

Petroleum Hydrocarbon Profiles of Water and Sediment of Algoa Bay, Eastern Cape, South Africa.

Science.gov (United States)

Adeniji, Abiodun O; Okoh, Omobola O; Okoh, Anthony I

2017-10-20

Petroleum hydrocarbon profiles of water and sediment samples of Algoa Bay in the Eastern Cape Province of South Africa were assessed using standard analytical procedures. Water (from surface and bottom levels) and sediment samples were collected from five locations in the bay from February to June 2016. Extraction of the petroleum hydrocarbons from the water and sediment samples collected was achieved using liquid-liquid and Soxhlet extraction techniques, respectively, followed by column clean up. Target compounds were analytically determined with gas chromatography-flame ionization detector (GC-FID) and quantified by integrating the areas of both the resolved and unresolved components. Physicochemical properties of the water samples were also determined on site using a SeaBird 19plusV2 CTD SBE 55 device. Estimated limit of detection, limit of quantitation and relative standard deviation for the 35 n -alkane standards ranged from 0.06 to 0.13 μg/L, 0.30 to 0.69 μg/L and 3.61 to 8.32%, respectively. Results showed that total petroleum hydrocarbon (TPH) varied from 45.07 to 307 μg/L in the water and 0.72 to 27.03 mg/kg in the sediments. The mean concentrations of TPH in both the water and sediment samples from Algoa Bay revealed a slight level of pollution. The diagnostic indices used showed that the hydrocarbons in the area were from both biogenic and anthropogenic sources. Hence, there is need for adequate regulation and control of all activities contributing to the levels of petroleum hydrocarbon in the marine environment for the safety of human, aquatic and wild lives in the area.

Site characterization and petroleum hydrocarbon plume mapping

Energy Technology Data Exchange (ETDEWEB)

Ravishankar, K. [Harding Lawson Associates, Houston, TX (United States)

1996-12-31

This paper presents a case study of site characterization and hydrocarbon contamination plume mapping/delineation in a gas processing plant in southern Mexico. The paper describes innovative and cost-effective use of passive (non-intrusive) and active (intrusive) techniques, including the use of compound-specific analytical methods for site characterization. The techniques used, on a demonstrative basis, include geophysical, geochemical, and borehole drilling. Geochemical techniques used to delineate the horizontal extent of hydrocarbon contamination at the site include soil gas surveys. The borehole drilling technique used to assess the vertical extent of contamination and confirm geophysical and geochemical data combines conventional hollow-stem auguring with direct push-probe using Geoprobe. Compound-specific analytical methods, such as hydrocarbon fingerprinting and a modified method for gasoline range organics, demonstrate the inherent merit and need for such analyses to properly characterize a site, while revealing the limitations of noncompound-specific total petroleum hydrocarbon analysis. The results indicate that the techniques used in tandem can properly delineate the nature and extent of contamination at a site; often supplement or complement data, while reducing the risk of errors and omissions during the assessment phase; and provide data constructively to focus site-specific remediation efforts. 7 figs.

Analysis of Oxidative Stress in Chronic Exposure to Petroleum Hydrocarbons in Karnataka, India

Directory of Open Access Journals (Sweden)

Suttur Malini

2017-03-01

Full Text Available Background:Several studies have reported the toxicological implications of inhalation of petroleum hydrocarbon fumes in animal models. But, there is certainly little or no documentation of the exposure to petroleum hydrocarbon fuel on oxidative stress levels in humans, unlike the pulmonary physiology. The present study was carried out to evaluate the effects of constituents of the hydrocarbon fuels on oxidative stress levels of the petrol fillers and tanker drivers. Methods: The study involved 165 males divided into three groups were the petrol fillers, tanker drivers and the controls. Case control data set was established wherein the control subjects are not exposed to hydrocarbon fuels with similar age. Serum samples of the subjects were collected and subjected for various biochemical assays. The enzymatic antioxidants such as superoxide dismutase, malondialdehyde a byproduct of lipid peroxidation and total antioxidant capacity of the individuals along with non-enzymatic antioxidant Vitamin A was estimated. Results: The results showed a no significant differences for age, body mass index, superoxide dismutase and levels of Malondialdehyde and total antioxidant capacity. But on the other hand, there is significant changes observed for total antioxidant capacity and vitamin A when exposed group is compared with control subject. Conclusion: It is evidential from the present study that prolonged exposure to petroleum hydrocarbon fumes leads to an increase in their oxidative stress in turn resulting broad spectrum of diseases. Hence, there is a raised need for public awareness about the health hazards in order to enable petrol attendants.

Biodegradation testing of hydrophobic chemicals in mixtures at low concentrations – covering the chemical space of petroleum hydrocarbons

DEFF Research Database (Denmark)

Birch, Heidi; Hammershøj, Rikke Høst; Mayer, Philipp

Petroleum products are complex mixtures of varying composition containing thousands of hydrocarbons each with their own physicochemical properties and degradation kinetics. One approach for risk assessment of these products is therefore to group the hydrocarbons by carbon number and chemical class...... i.e. hydrocarbon blocks. However, the biodegradation kinetic data varies in quantity and quality for the different hydrocarbon blocks, hampering the characterization of their fate properties. In this study, biodegradation kinetics of a large number of hydrocarbons aiming to cover the chemical space...... of petroleum hydrocarbons, were therefore determined at ng/L to µg/L concentrations in surface water, seawater and activated sludge filtrate. Two hydrocarbon mixtures were prepared, comprising a total of 53 chemicals including paraffins, naphthenics and aromatic hydrocarbons from C8 to C20. Passive dosing from...

The influence of dissolved petroleum hydrocarbon residues on natural phytoplankton biomass

Digital Repository Service at National Institute of Oceanography (India)

Shailaja, M.S.

on phytoplankton biomass varies depending on the nature rather than the quantity of petroleum hydrocarbons present. Culture studies with unialgal Nitzschia sp. in seawater collected from selected stations in the study area as well as in artificial seawater spiked...

The Effects of Environmental Factors on Biological Remediation of Petroleum Hydrocarbon Contaminated Soil

Directory of Open Access Journals (Sweden)

Mohammad reza Moslemi

2005-09-01

Full Text Available Among the consequences of discharging industrial wastes to land and water bodies, is the widespread accumulation and migration of toxic chemical mixtures in soil and groundwater resources. It is believed that the accumulation of contaminants in the environment constitutes a serious threat to ecological and human health. Bioremediation is an effective measure in dealing with such contaminations particularly those from petroleum hydrocarbon sources; moreover bioremediation is emerging as a promising technology for the treatment of soil and groundwater contamination. Therefore the goal of this study is discussing the theory and practice of biological remediation of petroleum hydrocarbon contaminated soils and assessing the effects of operational conditions and parameters such as: temperature, dissolved oxygen concentration and  pH on the removal rate of the target contaminant which is handled in the designed reactor. Due to large production and consumption rate of diesel fuel inIran and many other countries, diesel fuel has been selected as target contaminant. In this study TOC and COD testing methods have been used to measure and assess the removal rate of the contaminant in the reactor. The experimental results indicate that, considering the operational conditions the indigenous microorganisms which have been separated from the soil are able to remove 50 to 83 percent of the contaminant after 30 days. Thereafter on the base of the results and considering the laboratorial specifications and conditions applied in this project, the optimum values of temperature, dissolved oxygen concentration andpH were respectively determined as 35°C, 4mg/L and 7.

Bioremediation of Petroleum and Radiological Contaminated Soils at the Savannah River Site: Laboratory to Field Scale Applications

Energy Technology Data Exchange (ETDEWEB)

BRIGMON, ROBINL.

2004-06-07

In the process of Savannah River Site (SRS) operations limited amounts of waste are generated containing petroleum, and radiological contaminated soils. Currently, this combination of radiological and petroleum contaminated waste does not have an immediate disposal route and is being stored in low activity vaults. SRS developed and implemented a successful plan for clean up of the petroleum portion of the soils in situ using simple, inexpensive, bioreactor technology. Treatment in a bioreactor removes the petroleum contamination from the soil without spreading radiological contamination to the environment. This bioreactor uses the bioventing process and bioaugmentation or the addition of the select hydrocarbon degrading bacteria. Oxygen is usually the initial rate-limiting factor in the biodegradation of petroleum hydrocarbons. Using the bioventing process allowed control of the supply of nutrients and moisture based on petroleum contamination concentrations and soil type. The results of this work have proven to be a safe and cost-effective means of cleaning up low level radiological and petroleum-contaminated soil. Many of the other elements of the bioreactor design were developed or enhanced during the demonstration of a ''biopile'' to treat the soils beneath a Polish oil refinery's waste disposal lagoons. Aerobic microorganisms were isolated from the aged refinery's acidic sludge contaminated with polycyclic aromatic hydrocarbons (PAHs). Twelve hydrocarbon-degrading bacteria were isolated from the sludge. The predominant PAH degraders were tentatively identified as Achromobacter, Pseudomonas Burkholderia, and Sphingomonas spp. Several Ralstonia spp were also isolated that produce biosurfactants. Biosurfactants can enhance bioremediation by increasing the bioavailability of hydrophobic contaminants including hydrocarbons. The results indicated that the diversity of acid-tolerant PAH-degrading microorganisms in acidic oil wastes may

BIOREMEDIATION - TECHNOLOGY FOR DECONTAMINATION OF SOILS POLLUTED WITH PETROLEUM HYDROCARBONS

Directory of Open Access Journals (Sweden)

Irina-Ramona PECINGINĂ

2013-05-01

Full Text Available The pollution of soil with petroleum hydrocarbons prevents unfolding processes ofwater infiltration in soil, its circulation and the exchanges of the gaseous substances with theatmosphere. The biodegradation speed of the pollutants by the microorganisms is influenced ofsome factors: nutrients, soil type, humidity, temperature, pH, the type and the metabolism of themicroorganisms. The spill of the crude oil in the soil results in numerical growth of bacteriapopulations, with a concomitant reduction in their diversity, respectively with the predominantspecies that degrade hydrocarbons to simpler compounds, determining their gradualdisappearance.

Bioaccumulation of petroleum hydrocarbons in arctic amphipods in the oil development area of the Alaskan Beaufort Sea.

Science.gov (United States)

Neff, Jerry M; Durell, Gregory S

2012-04-01

An objective of a multiyear monitoring program, sponsored by the US Department of the Interior, Bureau of Ocean Energy Management was to examine temporal and spatial changes in chemical and biological characteristics of the Arctic marine environment resulting from offshore oil exploration and development activities in the development area of the Alaskan Beaufort Sea. To determine if petroleum hydrocarbons from offshore oil operations are entering the Beaufort Sea food web, we measured concentrations of hydrocarbons in tissues of amphipods, Anonyx nugax, sediments, Northstar crude oil, and coastal peat, collected between 1999 and 2006 throughout the development area. Mean concentrations of polycyclic aromatic hydrocarbons (PAH), saturated hydrocarbons (SHC), and sterane and triterpane petroleum biomarkers (StTr) were not significantly different in amphipods near the Northstar oil production facility, before and after it came on line in 2001, and in amphipods from elsewhere in the study area. Forensic analysis of the profiles (relative composition and concentrations) of the 3 hydrocarbon classes revealed that hydrocarbon compositions were different in amphipods, surface sediments where the amphipods were collected, Northstar crude oil, and peat from the deltas of 4 North Slope rivers. Amphipods and sediments contained a mixture of petrogenic, pyrogenic, and biogenic PAH. The SHC in amphipods were dominated by pristane derived from zooplankton, indicating that the SHC were primarily from the amphipod diet of zooplankton detritus. The petroleum biomarker StTr profiles did not resemble those in Northstar crude oil. The forensic analysis revealed that hydrocarbons in amphipod tissues were not from oil production at Northstar. Hydrocarbons in amphipod tissues were primarily from their diet and from river runoff and coastal erosion of natural diagenic and fossil terrestrial materials, including seep oils, kerogens, and peat. Offshore oil and gas exploration and development

Quantification of compositional changes of petroleum hydrocarbons by GC/FID and GC/MS during a long-term bioremediation experiment

DEFF Research Database (Denmark)

Jensen, Trine S.; Arvin, Erik; Svensmark, Bo

2000-01-01

Samples from a long-term bioremediation experiment contaminated with two crude oils, Arabian Heavy and Gullfax, was used to analyze the compositional change of petroleum hydrocarbons. A time course of five different homologous series of petroleum hydrocarbons were analysed by GC/FID and GC...

Combined in-situ and ex-situ bioremediation of petroleum hydrocarbon contaminated soils by closed-loop soil vapor extraction and air injection

International Nuclear Information System (INIS)

Hu, S.S.; Buckler, M.J.

1993-01-01

Treatment and restoration of petroleum hydrocarbon contaminated soils at a bulk petroleum above-ground storage tank (AST) site in Michigan is being conducted through in-situ and ex-situ closed-loop soil vapor extraction (SVE), soil vapor treatment, and treated air injection (AI) processes. The soil vapor extraction process applies a vacuum through the petroleum hydrocarbon affected soils in the ex-situ bio-remediation pile (bio-pile) and along the perimeter of excavated area (in-situ area) to remove the volatile or light petroleum hydrocarbons. This process also draws ambient air into the ex-situ bio-pile and in-situ vadose zone soil along the perimeter of excavated area to enhance biodegradation of light and heavy petroleum hydrocarbons in the soil. The extracted soil vapor is treated using a custom-designed air bio-remediation filter (bio-filter) to degrade the petroleum hydrocarbon compounds in the soil vapor extraction air streams. The treated air is then injected into a flush grade soil bed in the backfill area to perform final polishing of the air stream, and to form a closed-loop air flow with the soil vapor extraction perforated pipes along the perimeter of the excavated area

Simulation of enhanced in-situ biorestoration of petroleum hydrocarbons

International Nuclear Information System (INIS)

Borden, R.C.

1991-01-01

This paper discusses a general mathematical model being developed to aid in the design and analysis of projects for the enhanced aerobic bioremediation of petroleum-contaminated aquifers. Development of the enhanced biotransformation model is proceeding in three steps: development of an abiotic hydrocarbon dissolution model; coupling the dissolution model with existing equations for simulating aerobic biodegradation; and comparison with laboratory data. The model assumes that the residual hydrocarbon is distributed between two fractions, a fast fraction in equilibrium with the aqueous phase and a slow fraction in which mass transfer is limited. Overall, the model provides an excellent fit to the experimental data and requires a minimum of input parameters

Sustainable treatment of hydrocarbon-contaminated industrial land

OpenAIRE

Cunningham, Colin John

2012-01-01

Land contamination by petroleum hydrocarbons is a widespread and global environmental pollution issue from recovery and refining of crude oil and the ubiquitous use of hydrocarbons in industrial processes and applications. Sustainable treatment of hydrocarbon-contaminated industrial land was considered with reference to seven published works on contaminated railway land including the track ballast, crude oil wastes and contaminated refinery soils. A methodology was developed...

Validation of an analytical methodology for the quantitative analysis of petroleum hydrocarbons in marine sediment samples

Directory of Open Access Journals (Sweden)

Eloy Yordad Companioni Damas

2009-01-01

Full Text Available This work describes a validation of an analytical procedure for the analysis of petroleum hydrocarbons in marine sediment samples. The proposed protocol is able to measure n-alkanes and polycyclic aromatic hydrocarbons (PAH in samples at concentrations as low as 30 ng/g, with a precision better than 15% for most of analytes. The extraction efficiency of fortified sediments varied from 65.1 to 105.6% and 59.7 to 97.8%, for n-alkanes and PAH in the ranges: C16 - C32 and fluoranthene - benzo(apyrene, respectively. The analytical protocol was applied to determine petroleum hydrocarbons in sediments collected from a marine coastal zone.

Ecological risk assessment of a site contaminated with petroleum hydrocarbons

International Nuclear Information System (INIS)

Starodub, M.E.; Feniak, N.A.; Willes, R.F.; Moore, C.E.; Mucklow, L.

1995-01-01

The aquatic and terrestrial health risks associated with petroleum contamination on a decommissioned military base, contaminated with products ranging from Bunker C oil to aviation fuel, were assessed using a methodology whereby an analytical measurement of total petroleum hydrocarbons (TPH) could be correlated with compositional characterization and thus with toxicity. The constituents of petroleum hydrocarbon contamination represent wide ranges of physical-chemical properties, environmental fate, and toxicity. The composition of TPH can vary greatly, dependent on the sources or fuel types and the interaction of age as well as site- and chemical-specific characteristics in determining the impact of weathering processes. Therefore, a bulk sum analysis of TPH cannot be related to toxicity without characterization of its composition and association of the constituents, and therefore composition, with actual toxicity data. To address this need, the constituents of TPH were represented by surrogate chemicals, with selection based on structure-activity relationships and available toxicity data. Toxicological profiles were developed from governmental regulations and on the published literature for both the aquatic and terrestrial media. Risk characterization consisted of a comparison of water concentration limits and exposure limits, developed for each surrogate, to estimated surrogate concentrations throughout the site. The concentrations of surrogates were extrapolated from TPH composition characterization analyses, conducted at a select number of sampling locations, to bulk sum analyses of TPH at related sampling locations

Phytoremediation of petroleum hydrocarbon-contaminated saline-alkali soil by wild ornamental Iridaceae species.

Science.gov (United States)

Cheng, Lijuan; Wang, Yanan; Cai, Zhang; Liu, Jie; Yu, Binbin; Zhou, Qixing

2017-03-04

As a green remediation technology, phytoremediation is becoming one of the most promising methods for treating petroleum hydrocarbons (PHCs)-contaminated soil. Pot culture experiments were conducted in this study to investigate phytoremediation potential of two representative Iridaceae species (Iris dichotoma Pall. and Iris lactea Pall.) in remediation of petroleum hydrocarbon-contaminated saline-alkali soil from the Dagang Oilfield in Tianjin, China. The results showed that I. lactea was more endurable to extremely high concentration of PHCs (about 40,000 mg/kg), with a relatively high degradation rate of 20.68%.The degradation rate of total petroleum hydrocarbons (TPHs) in soils contaminated with 10,000 and 20,000 mg/kg of PHCs was 30.79% and 19.36% by I. dichotoma, and 25.02% and 19.35% by I. lactea, respectively, which improved by 10-60% than the unplanted controls. The presence of I. dichotoma and I. lactea promoted degradation of PHCs fractions, among which saturates were more biodegradable than aromatics. Adaptive specialization was observed within the bacterial community. In conclusion, phytoremediation by I. dichotoma should be limited to soils contaminated with ≤20,000 mg/kg of PHCs, while I. lactea could be effectively applied to phytoremediation of contaminated soils by PHCs with at least 40,000 mg/kg.

Dispersion, sorption and photodegradation of petroleum hydrocarbons in dispersant-seawater-sediment systems.

Science.gov (United States)

Zhao, Xiao; Liu, Wen; Fu, Jie; Cai, Zhengqing; O'Reilly, S E; Zhao, Dongye

2016-08-15

This work examined effects of model oil dispersants on dispersion, sorption and photodegradation of petroleum hydrocarbons in simulated marine systems. Three dispersants (Corexit 9500A, Corexit 9527A and SPC 1000) were used to prepare dispersed water accommodated oil (DWAO). While higher doses of dispersants dispersed more n-alkanes and PAHs, Corexit 9500A preferentially dispersed C11-C20 n-alkanes, whereas Corexit 9527A was more favorable for smaller alkanes (C10-C16), and SPC 1000 for C12-C28 n-alkanes. Sorption of petroleum hydrocarbons on sediment was proportional to TPH types/fractions in the DWAOs. Addition of 18mg/L of Corexit 9500A increased sediment uptake of 2-3 ring PAHs, while higher dispersant doses reduced the uptake, due to micelle-enhanced solubilization effects. Both dispersed n-alkanes and PAHs were susceptible to photodegradation under simulated sunlight. For PAHs, both photodegradation and photo-facilitated alkylation were concurrently taking place. The information can facilitate sounder assessment of fate and distribution of dispersed oil hydrocarbons in marine systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

New Hydrocarbon Degradation Pathways in the Microbial Metagenome from Brazilian Petroleum Reservoirs

Science.gov (United States)

Sierra-García, Isabel Natalia; Correa Alvarez, Javier; Pantaroto de Vasconcellos, Suzan; Pereira de Souza, Anete; dos Santos Neto, Eugenio Vaz; de Oliveira, Valéria Maia

2014-01-01

Current knowledge of the microbial diversity and metabolic pathways involved in hydrocarbon degradation in petroleum reservoirs is still limited, mostly due to the difficulty in recovering the complex community from such an extreme environment. Metagenomics is a valuable tool to investigate the genetic and functional diversity of previously uncultured microorganisms in natural environments. Using a function-driven metagenomic approach, we investigated the metabolic abilities of microbial communities in oil reservoirs. Here, we describe novel functional metabolic pathways involved in the biodegradation of aromatic compounds in a metagenomic library obtained from an oil reservoir. Although many of the deduced proteins shared homology with known enzymes of different well-described aerobic and anaerobic catabolic pathways, the metagenomic fragments did not contain the complete clusters known to be involved in hydrocarbon degradation. Instead, the metagenomic fragments comprised genes belonging to different pathways, showing novel gene arrangements. These results reinforce the potential of the metagenomic approach for the identification and elucidation of new genes and pathways in poorly studied environments and contribute to a broader perspective on the hydrocarbon degradation processes in petroleum reservoirs. PMID:24587220

Degradation of Total Petroleum Hydrocarbon in Phytoremediation Using Terrestrial Plants

Directory of Open Access Journals (Sweden)

Mushrifah Idris

2014-06-01

Full Text Available This study focused on the total petroleum hydrocarbon (TPH degradation in phytoremediation of spiked diesel in sand. The diesel was added to the sand that was planted with terrestrial plants. Four selected terrestrial plants used were Paspalum vaginatum Sw, Paspalums crobiculatum L. varbispicatum Hack, Eragrotis atrovirens (Desf. Trin. ex Steud and Cayratia trifolia (L. Domin since all the plants could survive at a hydrocarbon petroleum contaminated site in Malaysia. The samplings were carried out on Day 0, 7, 14, 28, 42 and 72. The analysis of the TPH was conducted by extracting the spiked sand using ultrasonic extraction. The determination of the TPH concentration in the sand was performed using GC-FID. The degradation of TPH depends on the plant species and time of exposure. The highest percentage degradation by P. vaginatum, P. scrobiculatum, E. atrovirens and C. trifolia were 91.9, 74.0, 68.9 and 62.9%, respectively. In conclusion, the ability to degrade TPH by plants were P. vaginatum > P. scrobiculatum > E. atrovirens> C. trifolia.

Predicting the environmental fate properties of petroleum hydrocarbon mixtures

International Nuclear Information System (INIS)

Pisigan, R.A. Jr.; Tucker, W.A.

1995-01-01

The environmental fate and transport of petroleum products for risk assessment can be evaluated based on the physico-chemical properties of an indicator chemical or a surrogate compound, or the whole mixture. A study was conducted to develop a simple representation of the hydrocarbon mixture as if it contained only few constituents, each of which represents a large number of compounds. The products considered are gasoline, diesel fuel, and jet fuel (JP4). Each petroleum hydrocarbon was characterized as a mixture of six constituents: short chain alkanes, long chain alkanes, short chain cycloalkanes and alkenes, long chain cycloalkanes and alkenes, BTEX, and other aromatics. The carbon number used as a cut-off between short and long chain alkanes, alkenes, and cycloalkanes varies with the type of product. Each mixture has different average molecular weight, water solubility, vapor pressure, organic carbon partition coefficient, and air diffusivity. The properties of each constituent of gasoline were derived from the weighted average of all compounds belonging to each constituent group. For diesel fuel and JP4, the properties of each constituent were generated from the properties of the component most representative of the group. Any property that is missing or not available from common literature sources was derived from regression equations developed from the data base for gasoline. These regression equations express the property as function of the number of carbon atoms. The R 2 values of the regression equations range from 0.82--0.92. Some case studies involving petroleum product contamination in which the estimated properties were applied are presented

Enumeration of petroleum hydrocarbon utilizing bacteria

International Nuclear Information System (INIS)

Mukherjee, S.; Barot, M.; Levine, A.D.

1996-01-01

In-situ biological treatment is one among a number of emerging technologies that may be applied to the remediation of contaminated soils and groundwater. In 1985, a surface spill of 1,500 gallons of dielectric transformer oil at the Sandia National Laboratories (HERMES II facility) resulted in contamination of soil up to depths of 160 feet. The extent of contamination and site characteristics favored the application of in-situ bioremediation as a potential remedial technology. The purpose of this research was to enumerate indigenous microbial populations capable of degrading petroleum hydrocarbons. Microbial enumeration and characterization methods suitably adapted for hydrocarbon utilizing bacteria were used as an indicator of the presence of viable microbial consortia in excavated oil samples with hydrocarbon (TPH) concentrations ranging from 300 to 26,850 ppm. Microbial activity was quantified by direct and streak plating soil samples on silica gel media. Effects of toxicity and temperature were studied using batch cultures of hydrocarbon utilizing bacteria (selectively isolated in an enrichment medium), at temperatures of 20 and 35 C. It was concluded from this study that it is possible to isolate native microorganisms from contaminated soils from depths of 60 to 160 feet, and with oil concentration ranging from 300 to 26,850 ppm. About 62% of the microorganisms isolated form the contaminated soil were capable of using contaminant oil as a substrate for growth and metabolism under aerobic conditions. Growth rates were observed to be 50% higher for the highest contaminant concentration at 20 C. Resistance to toxicity to contaminant oil was also observed to be greater at 20 C than at 35 C

The characterization of petroleum and creosote-contaminated soils: Class component analysis by thin layer chromatography with flame ionization detection

International Nuclear Information System (INIS)

Pollard, S.J.T.; Hrudey, S.E.; Fuhr, B.J.; Alex, R.F.; Holloway, L.R.

1992-01-01

The assessment and reclamation of coal tar, creosote and petroleum-contaminated sites is emerging as a major challenge to industry and the federal and provincial Canadian governments. Contaminants frequently include polynuclear aromatic compounds (PAH), several high molecular weight analogues of which are documented carcinogens. Adaptation of thin layer chromatography with flame ionization detection for the analysis of hydrocarbon-contaminated soils is described. The method is directly applicable to the analysis of oily waste extracts from petroleum and creosote wood preservative site soils and is capable of distinguishing between the saturate, aromatic and polar components of waste residues. The method provides a rapid, low cost class component analysis of heavy hydrocarbon waste extracts and is particularly useful for estimating the extent of weathering experienced by chronically exposed hydrocarbon wastes in the soil environment. As such, it is useful as a screening tool for a preliminary assessment of the biotreatability or inherent recalcitrance of hydrocarbon waste mixtures. 11 refs., 5 figs

Migrated hydrocarbons in outcrop samples: revised petroleum exploration directions in the Tarim Basin

Energy Technology Data Exchange (ETDEWEB)

Li, Maowen; Snowdon, Lloyd [Geological Survey of Canada, Calgary, AB (Canada); Xiao, Zhongyao [CNPC Tarim Petroleum Exploration Bureau, Kuerle, Xinjiang (China); Lin, Renzi [Petroleum Univ., Changping, Beijing (China); Wang, Peirong; Hou, Dujie [Jianghan Petroleum Univ., Hubei (China); Zhang, Linye [SINOPEC Shengli Petroleum Bureau, Dongying, Shandong (China); Zhang, Shuichang; Liang, Digang [Research Inst. of Petroleum Exploration and Development, Beijing (China)

2000-07-01

The application of age-specific biomarker distributions established from mature exploration areas of the Tarim Basin, northwestern China, indicates that most Carboniferous-Permian outcrop samples in the eastern segment of the Southwest Depression, previously believed to have significant petroleum source potential, in fact contain migrated hydrocarbons derived from Cambrian-Lower Ordovician strata. New geochemical results have led to a major revision of petroleum exploration directions in this area. (Author)

Combination of biochar amendment and phytoremediation for hydrocarbon removal in petroleum-contaminated soil

OpenAIRE

Han, Tao; Zhao, Zhipeng; Bartlam, Mark; Wang, Yingying

2016-01-01

Remediation of soils contaminated with petroleum is a challenging task. Four different bioremediation strategies, including natural attenuation, biochar amendment, phytoremediation with ryegrass, and a combination of biochar and ryegrass, were investigated with greenhouse pot experiments over a 90-day period. The results showed that planting ryegrass in soil can significantly improve the removal rate of total petroleum hydrocarbons (TPHs) and the number of microorganisms. Within TPHs, the rem...

Fingerprinting of petroleum hydrocarbons (PHC) and other biogenic organic compounds (BOC) in oil-contaminated and background soil samples.

Science.gov (United States)

Wang, Zhendi; Yang, C; Yang, Z; Hollebone, B; Brown, C E; Landriault, M; Sun, J; Mudge, S M; Kelly-Hooper, F; Dixon, D G

2012-09-01

Total petroleum hydrocarbons (TPH) or petroleum hydrocarbons (PHC) are one of the most widespread soil contaminants in Canada, the United States and many other countries worldwide. Clean-up of PHC-contaminated soils costs the Canadian economy hundreds of millions of dollars annually. In Canada, most PHC-contaminated site evaluations are based on the methods developed by the Canadian Council of the Ministers of the Environment (CCME). However, the CCME method does not differentiate PHC from BOC (the naturally occurring biogenic organic compounds), which are co-extracted with petroleum hydrocarbons in soil samples. Consequently, this could lead to overestimation of PHC levels in soil samples. In some cases, biogenic interferences can even exceed regulatory levels (300 μg g(-1) for coarse soils and 1300 μg g(-1) for fine soils for Fraction 3, C(16)-C(34) range, in the CCME Soil Quality Level). Resulting false exceedances can trigger unnecessary and costly cleanup or remediation measures. Therefore, it is critically important to develop new protocols to characterize and quantitatively differentiate PHC and BOC in contaminated soils. The ultimate objective of this PERD (Program of Energy Research and Development) project is to correct the misconception that all detectable hydrocarbons should be regulated as toxic petroleum hydrocarbons. During 2009-2010, soil and plant samples were collected from over forty oil-contaminated and paired background sites in various provinces. The silica gel column cleanup procedure was applied to effectively remove all target BOC from the oil-contaminated sample extracts. Furthermore, a reliable GC-MS method in combination with the derivatization technique, developed in this laboratory, was used for identification and characterization of various biogenic sterols and other major biogenic compounds in these oil-contaminated samples. Both PHC and BOC in these samples were quantitatively determined. This paper reports the characterization

Dissolved petroleum hydrocarbon concentrations in some regions of the northern Indian Ocean

Digital Repository Service at National Institute of Oceanography (India)

SenGupta, R.; Qasim, S.Z.; Fondekar, S.P.; Topgi, R.S.

Dissolved petroleum hydrocarbons were measured in some parts of the Northern Indian Ocean using UV bsorbance technique with a clean up step. The concentration of oil ranged from 0.6 to 26.5 mu gl. Higher values were recorded along the oil tanker...

A closer look at bioaccumulation of petroleum hydrocarbon mixtures in aquatic worms.

NARCIS (Netherlands)

Muijs, B.; Jonker, M.T.O.

2010-01-01

Petroleum hydrocarbons (oils) are ubiquitous in the aquatic environment, and adequate risk assessment is thus essential. Bioaccumulation plays a key role in risk assessment, but the current knowledge on bioaccumulation of oils is limited. Therefore, this process was studied in detail, using the

Toxicity of petroleum hydrocarbon distillates to soil organisms.

Science.gov (United States)

Cermak, Janet H; Stephenson, Gladys L; Birkholz, Detlef; Wang, Zhendi; Dixon, D George

2010-12-01

Canadian standards for petroleum hydrocarbons in soil are based on four distillate ranges (F1, C6-C10; F2, >C10-C16; F3, >C16-C34; and F4, >C34). Concerns have arisen that the ecological soil contact standards for F3 may be overly conservative. Oil distillates were prepared and characterized, and the toxicity of F3 and two subfractions, F3a (>C16-C23) and F3b (>C23-C34), to earthworms (Eisenia andrei), springtails (Orthonychiurus folsomi), and northern wheatgrass (Elymus lanceolatus), as well as the toxicity of F2 to earthworms, was determined. Clean soil was spiked with individual distillates and measured concentrations were determined for select tests. Results agree with previous studies with these distillates. Reported toxicities of crude and petroleum products to invertebrates were generally comparable to that of F3 and F3a. The decreasing order of toxicity was F3a > F3 > F3b with invertebrates, and F3a > F3b > F3 with plants. The toxicities of F3a and F3b were not sufficiently different to recommend regulating hydrocarbons based on these distillate ranges. The results also suggest that test durations may be insufficient for determining toxicity of higher distillate ranges, and that the selection of species and endpoints may significantly affect interpretation of toxicity test results. Copyright © 2010 SETAC.

Investigation and monitoring of a petroleum hydrocarbon plume in the Blue Ridge Physiographic Province of southwestern Virginia

International Nuclear Information System (INIS)

Risner, A.C.

1995-01-01

Petroleum was observed in a ditch between two bulk petroleum facilities in southwestern Virginia. Employees of an adjacent furniture factory reported to the local Hazardous Materials Team that petroleum fumes were present in factory buildings. A total of thirty seven soil borings and twenty four monitoring wells were installed and sampled. Field measurements indicated that liquid phase petroleum hydrocarbons were not present in the monitoring wells. Laboratory results from soil samples indicated total petroleum hydrocarbons as gasoline were present at concentrations as high as 1,000,000 micrograms per kilogram. Laboratory results of ground water sampling indicated concentrations of benzene as high as 3,100 micrograms per liter. Due to the urban location of the site, a secure public water source was available. Based on the availability of public water and the absence of liquid phase petroleum at the site, it was determined that the risk to human health from exposure to petroleum compounds was minimal. A Site Characterization Report was prepared to summarize site conditions and the information gathered during the site investigation. The report recommended ground water monitoring based on the lack of complete exposure pathways. The DEQ agreed with the recommendation for monitoring

The use of polynuclear aromatic hydrocarbon (PAH) alkyl homologues in determining petroleum source identification and weathering

International Nuclear Information System (INIS)

Brown, J.S.; Boehm, P.D.; Sauer, T.C.; Wong, W.M.C.

1993-01-01

Techniques utilizing double ratio plots of selected polynuclear aromatic hydrocarbon (PAH) alkyl homologues were used to identify and distinguish crude oils and refined petroleum products from each other and to distinguish petroleum sources in complex pollutant regimes. Petroleum samples were fractionated by high performance liquid chromatography (HPLC) into saturated and aromatic (PAH) hydrocarbon fractions. The saturated hydrocarbon fractions were then analyzed by gas chromatography/flame ionization detection (GC/FID) to obtain a resolved/unresolved alkane fingerprint of each oil. The aromatic fractions of the oils were analyzed by gas chromatography/mass spectrometry (GC/MS) for PAH and selected alkyl homologues. Comparisons of the saturated hydrocarbon fingerprints indicated that some oils were indistinguishable based on the alkane fingerprint alone. Another double ratio plot of the alkyl chrysenes and alkyl dibenzothiophenes was effective in establishing the weathering of oil in environmental samples which were processed using the same analytical techniques, since the dibenzothiophenes are degraded more rapidly than the chrysenes. The application of selected ratios in oil spill source identification in complex environmental samples from Suisin Bay California and Boston Harbor are discussed. The use of ratios to measure the extent of weathering in oil spill samples from Prince William Sound and the Gulf of Alaska is examined

Biological Treatment of Petroleum in Radiologically Contaminated Soil

Energy Technology Data Exchange (ETDEWEB)

BERRY, CHRISTOPHER

2005-11-14

This chapter describes ex situ bioremediation of the petroleum portion of radiologically co-contaminated soils using microorganisms isolated from a waste site and innovative bioreactor technology. Microorganisms first isolated and screened in the laboratory for bioremediation of petroleum were eventually used to treat soils in a bioreactor. The bioreactor treated soils contaminated with over 20,000 mg/kg total petroleum hydrocarbon and reduced the levels to less than 100 mg/kg in 22 months. After treatment, the soils were permanently disposed as low-level radiological waste. The petroleum and radiologically contaminated soil (PRCS) bioreactor operated using bioventing to control the supply of oxygen (air) to the soil being treated. The system treated 3.67 tons of PCRS amended with weathered compost, ammonium nitrate, fertilizer, and water. In addition, a consortium of microbes (patent pending) isolated at the Savannah River National Laboratory from a petroleum-contaminated site was added to the PRCS system. During operation, degradation of petroleum waste was accounted for through monitoring of carbon dioxide levels in the system effluent. The project demonstrated that co-contaminated soils could be successfully treated through bioventing and bioaugmentation to remove petroleum contamination to levels below 100 mg/kg while protecting workers and the environment from radiological contamination.

Endocrine, Physiological and Histopathological Responses of Fish and their Larvae to Stress with Emphasis on Exposure to Crude Oil and Various Petroleum Hydrocarbons

Directory of Open Access Journals (Sweden)

A. Y. A. AL-Kindi

2000-12-01

Full Text Available Various endocrine and physiological responses of fish exposed to forceful physical and chemical stimuli are reviewed with emphasis on the effects of crude oils and their hydrocarbon constituents. The chemistry and toxicity of petroleum hydrocarbons are examined and methods for experimental exposure of fish to crude oil and petroleum hydrocarbons are considered. A variety of blood-borne parameters recognized as reliable tools in determining the relative severity of stress in fish are reviewed. The effects of stress and petroleum hydrocarbons on endocrine responses including changes in plasma catecholamines, corticosteroids, and thyroid hormones are reviewed. The physiological responses: changes in plasma glucose, osmotic and ionic regulation, blood oxygen, hematocrit and hemoglobin concentration are explored, and histopathological effects of crude oil on fish are reviewed. Recent studies of the effects of petroleum hydrocarbons on fish larvae are considered and the increased sensitivity of the early life stages of fish are highlighted.

Petroleum environmental research forum field study on biofilters for control of volatile hydrocarbons

International Nuclear Information System (INIS)

Leson, G.; Smith, B.J.

1997-01-01

A field study on the treatment of volatile petroleum hydrocarbons (PHC) by biofiltration was conducted by the Petroleum Environmental Research Forum (PERF) between 1992 and 1994. Its objective was to assess the technical, regulatory, and economic feasibility of biofiltration for off-gases from petroleum processing and soil remediation equipment. It involved three small-scale biofilters provided by US vendors, treating off-gas from two soil vapor extraction sites and a source of refinery wastewater. Comprehensive monitoring of biofilter operating parameters and performance was conducted. Typically more than 95% of aromatic compounds such as benzene, and odorous reduced sulfur compounds can be removed at residence times of one minute or less, while removal of more than 70% of light aliphatics will require residence times of several minutes, and will thus require correspondingly large filter volumes and higher capital expenditure. The high percentage removal of aromatic hazardous air pollutants (HAP) and odors can generally be accomplished at comparatively short residence times while the need for high-percentage removal, particular of light aliphatics ( 5 ) will generally render biofiltration noncompetitive. Finally, a preliminary economic comparison of biofilters and established control technologies suggested that biofiltration may, for a representative design case involving off-gas from a refinery wastewater treatment operation, offer considerable savings in total cost of air pollution control for petroleum hydrocarbon streams if regulations require the control of aromatic HAP or odors

Distribution and activity of petroleum hydrocarbon degrading bacteria in the North Sea and Baltic Sea

International Nuclear Information System (INIS)

Bruns, K.; Dahlmann, G.; Gunkel, W.

1993-01-01

Data were collected in 1988 and 1989 on the distribution and activity of petroleum hydrocarbon degrading bacteria in the North Sea and Baltic Sea. Crude oil degrading bacteria and the number of bacteria which in particular degrade naphthalene were quantified using a modified dilution method (MPN). Crude oil degrading bacteria were present in all of about 100 water samples, with as many as 10 3 ml -1 in some samples. Numbers of naphthalene degrading bacteria were at least tenfold lower. There is obviously a greater connection between this bacteria group and petroleum hydrocarbon (PHC) contamination than between the more nonspecific group of crude oil degrading bacteria and PHC contamination. Data from the North Sea show an extremely high abundance of hydrocarbon degrading bacteria, even in winter, while in the southern Baltic Sea low numbers of bacteria were found and slower crude oil degradation was observed. (orig.)

Microbial metabolism and community structure in response to bioelectrochemically enhanced remediation of petroleum hydrocarbon-contaminated soil.

Science.gov (United States)

Lu, Lu; Huggins, Tyler; Jin, Song; Zuo, Yi; Ren, Zhiyong Jason

2014-04-01

This study demonstrates that electrodes in a bioelectrochemical system (BES) can potentially serve as a nonexhaustible electron acceptor for in situ bioremediation of hydrocarbon contaminated soil. The deployment of BES not only eliminates aeration or supplement of electron acceptors as in contemporary bioremediation but also significantly shortens the remediation period and produces sustainable electricity. More interestingly, the study reveals that microbial metabolism and community structure distinctively respond to the bioelectrochemically enhanced remediation. Tubular BESs with carbon cloth anode (CCA) or biochar anode (BCA) were inserted into raw water saturated soils containing petroleum hydrocarbons for enhancing in situ remediation. Results show that total petroleum hydrocarbon (TPH) removal rate almost doubled in soils close to the anode (63.5-78.7%) than that in the open circuit positive controls (37.6-43.4%) during a period of 64 days. The maximum current density from the BESs ranged from 73 to 86 mA/m(2). Comprehensive microbial and chemical characterizations and statistical analyses show that the residual TPH has a strongly positive correlation with hydrocarbon-degrading microorganisms (HDM) numbers, dehydrogenase activity, and lipase activity and a negative correlation with soil pH, conductivity, and catalase activity. Distinctive microbial communities were identified at the anode, in soil with electrodes, and soil without electrodes. Uncommon electrochemically active bacteria capable of hydrocarbon degradation such as Comamonas testosteroni, Pseudomonas putida, and Ochrobactrum anthropi were selectively enriched on the anode, while hydrocarbon oxidizing bacteria were dominant in soil samples. Results from genus or phylum level characterizations well agree with the data from cluster analysis. Data from this study suggests that a unique constitution of microbial communities may play a key role in BES enhancement of petroleum hydrocarbons

Petroleum hydrocarbon contaminated sites: a review of investigation and remediation regulations and processes

Energy Technology Data Exchange (ETDEWEB)

Epelbaum, Michel; Claudio, Jair R [Bureau Veritas do Brasil Sociedade Classificadora e Certificadora Ltda., Sao Paulo, SP (Brazil)

1994-12-31

This paper discusses alternatives on remediation of petroleum hydrocarbon contaminated sites which include groundwater remediation techniques and soil remediation techniques. Finally, the work points out some trends of sites remediation in Brazil and abroad. 6 refs., 1 fig., 7 tabs.

Petroleum hydrocarbon contaminated sites: a review of investigation and remediation regulations and processes

Energy Technology Data Exchange (ETDEWEB)

Epelbaum, Michel; Claudio, Jair R. [Bureau Veritas do Brasil Sociedade Classificadora e Certificadora Ltda., Sao Paulo, SP (Brazil)

1993-12-31

This paper discusses alternatives on remediation of petroleum hydrocarbon contaminated sites which include groundwater remediation techniques and soil remediation techniques. Finally, the work points out some trends of sites remediation in Brazil and abroad. 6 refs., 1 fig., 7 tabs.

Waste Plastic Converting into Hydrocarbon Fuel Materials

Energy Technology Data Exchange (ETDEWEB)

Sarker, Moinuddin; Mamunor Rashid, Mohammad; Molla, Mohammad

2010-09-15

The increased demand and high prices for energy sources are driving efforts to convert organic compounds into useful hydrocarbon fuels. Although much of this work has focused on biomass, there are strong benefits to deriving fuels from waste plastic material. Natural State Research Inc. (NSR) has invented a simple and economically viable process to decompose the hydrocarbon polymers of waste plastic into the shorter chain hydrocarbon of liquid fuel (patent pending). The method and principle of the production / process will be discussed. Initial tests with several widely used polymers indicate a high potential for commercialization.

Using microorganisms to aid in hydrocarbon degradation

International Nuclear Information System (INIS)

Black, W.; Zamora, J.

1993-01-01

Aliphatic hydrocarbons are threatening the potable water supply and the aquatic ecosystem. Given the right microbial inhabitant(s), a large portion of these aliphatic hydrocarbons could be biodegraded before reaching the water supply. The authors' purpose is to isolate possible oil-degrading organisms. Soil samples were taken from hydrocarbon-laden soils at petroleum terminals, a petroleum refinery waste-treatment facility, a sewage-treatment plant grease collector, a site of previous bioremediation, and various other places. Some isolates known to be good degraders were obtained from culture collection services. These samples were plated on a 10w-30 multigrade motor oil solid medium to screen for aliphatic hydrocarbon degraders. The degrading organisms were isolated, identified, and tested (CO 2 evolution, BOD, and COD) to determine the most efficient degrader(s). Thirty-seven organisms were tested, and the most efficient degraders were Serratia marcescens, Escherichia coli, and Enterobacter agglomerans

The conversion of waste plastics/petroleum residue mixtures to transportation fuels

International Nuclear Information System (INIS)

Ali, M.F.; Siddiqui, M.N.

2005-01-01

Plastics have become the material of choice in the modern world and its applications in the industrial field are continually increasing. Presently the plastics are manufactured for various uses such as: consumer packaging, wires, pipes, containers, bottles, appliances, electrical/electronic parts, computers and automotive parts. Most of he post consumer, plastic products are discarded and end up as mixed plastic municipal waste. The disposal of his waste has become a major social concern. Mixed plastic waste (MPW) recycling is still very much in its infancy. Approximately 20 million tons of plastic waste is generated in the United States of America, while about 15 million tons is generated throughout the Europe. With existing recycle efforts, only 7% of the MPW are recycled to produce low-grade plastic products such as plastic sacks, pipes, plastic fencing, and garden furniture. The current plastic reclamation technology options are generally grouped into the following four types: (i) Primary: The processing of plastic for use comparable to the original application. (ii) Secondary: The processing of plastics waste into new products with a lower quality level. (iii) Tertiary: The chemical or thermal processing of plastic waste to their basic hydrocarbon feedstock. The resulting raw materials are then reprocessed into plastic material or other products of the oil refining process. (iv) Quaternary: The incineration of plastics waste to recover energy. This paper deals exclusively with tertiary recycling by pyrolysis and catalytic cracking of plastics waste alone and by coprocessing with petroleum residue or heavy oils to fuels and petrochemical feedstock for further processing in existing refinery and petrochemical units. (author)

Improvement of phytoremediation of an aged petroleum hydrocarbon-contaminated soil by Rhodococcus erythropolis CD 106 strain.

Science.gov (United States)

Płociniczak, Tomasz; Fic, Ewa; Pacwa-Płociniczak, Magdalena; Pawlik, Małgorzata; Piotrowska-Seget, Zofia

2017-07-03

The aim of this study was to assess the impact of soil inoculation with the Rhodococcus erythropolis CD 106 strain on the effectiveness of the phytoremediation of an aged hydrocarbon-contaminated [approx. 1% total petroleum hydrocarbon (TPH)] soil using ryegrass (Lolium perenne). The introduction of CD 106 into the soil significantly increased the biomass of ryegrass and the removal of hydrocarbons in planted soil. The fresh weight of the shoots and roots of plants inoculated with CD 106 increased by 49% and 30%, respectively. After 210 days of the experiment, the concentration of TPH was reduced by 31.2%, whereas in the planted, non-inoculated soil, it was reduced by 16.8%. By contrast, the concentration of petroleum hydrocarbon decreased by 18.7% in non-planted soil bioaugmented with the CD 106 strain. The rifampicin-resistant CD 106 strain survived after inoculation into soil and was detected in the soil during the entire experimental period, but the number of CD 106 cells decreased constantly during the enhanced phytoremediation and bioaugmentation experiments. The plant growth-promoting and hydrocarbon-degrading properties of CD 106, which are connected with its long-term survival and limited impact on autochthonous microflora, make this strain a good candidate for improving the phytoremediation efficiency of soil contaminated with hydrocarbons.

INTEGRATED ASSESSMENT AND GEOSPATIAL ANALYSIS OF ACCUMULATION OF PETROLEUM HYDROCARBONS IN THE SOIL COVER OF SAKHALIN ISLAND

Directory of Open Access Journals (Sweden)

V. V. Dmitriev

2017-01-01

Full Text Available The article considers the approach to the integral estimation of the assessment of petroleum hydrocarbons (PHc in the soil cover of Sakhalin Island. The soil map of Sakhalin was used as the cartographic base for this work. The soil map includes 103 soil polygons. An additional information on soils was also taken from The Soil Atlas of the Russian Federation. As an integral criterion for the accumulation of PHc, it is proposed to use an integral indicator calculated on the basis of 5 evaluation criteria. The choice of criteria for the assessment was based on the works of Russian scientists. The evaluation criteria on each of the polygons include information on the soil texture, the total thickness of the organic and humus horizons, the content of organic carbon in these horizons and the content of organic carbon in the mineral horizons, as well as the presence of a gley barrier.The calculation of the integral indicator is based on the principles of the ASPID methodology. On this basis, the authors compiled the map of the potential capacity of Sakhalin soils to accumulate petroleum hydrocarbons. On the basis of GIS-technology using the estimates of the integral indicator, the analysis has been performed revealing the features of spatial differentiation of PHc accumulation in the soil cover.The analysis and assessment of the accumulations of petroleum hydrocarbons has shown that peaty and peat boggy soil have the greatest ability to holding the PHc. The lowest ability to accumulate petroleum hydrocarbons is typical of illuvial-ferruginous podzols (illuvial low-humic podzols. The soils of this group occupy 1% of the island. In general, soils with low and very low hydrocarbon accumulation capacity occupy less than forty percent of the territory. 

Investigation of the toxicokinetics of petroleum hydrocarbon distillates with the earthworm Eisenia andrei.

Science.gov (United States)

Cermak, Janet; Stephenson, Gladys; Birkholz, Detlef; Dixon, D George

2013-04-01

The Canada-wide standards for petroleum hydrocarbons in soils regulate petroleum hydrocarbons based on four distillate ranges: F1 (C6-C10), F2 (>C10-C16), F3 (>C16-C34), and F4 (>C34). Previous toxicity tests with earthworms and F2, as well as two subfractions of F3, F3a (>C16-C23) and F3a (>C23-C34), indicate that test durations might not be sufficiently long to reach threshold effect concentrations, likely because of the differing toxicokinetics for each distillate. A study was conducted to determine the toxicokinetics of both aliphatic and aromatic fractions of F2, F3a, and F3b with the earthworm Eisenia andrei. Peak accumulation curves were observed for F2 aliphatics and aromatics and F3a aromatics, likely as a result of changes in exposure concentration over the test duration via loss or a decrease in the bioavailable fraction. Biota-soil accumulation factors were >1 for total F2 aliphatics and aromatics and F3a aromatics as well as for several individual polyaromatic hydrocarbons for each distillate. Aromatics were disproportionately accumulated over aliphatics and were the main contributors to toxicity; therefore, aromatics and aliphatics should be regulated separately. The toxicokinetics were used to interpret previous toxicity data. Higher molecular weight distillates need longer-than-standard test durations to determine toxicity, so toxicity test results from fixed, standard-duration tests are not strictly comparable for these petroleum distillates. Copyright © 2013 SETAC.

Bioremediation of oil-contaminated soil using Candida catenulata and food waste

International Nuclear Information System (INIS)

Joo, Hung-Soo; Ndegwa, Pius M.; Shoda, Makoto; Phae, Chae-Gun

2008-01-01

Even though petroleum-degrading microorganisms are widely distributed in soil and water, they may not be present in sufficient numbers to achieve contaminant remediation. In such cases, it may be useful to inoculate the polluted area with highly effective petroleum-degrading microbial strains to augment the exiting ones. In order to identify a microbial strain for bioaugmentation of oil-contaminated soil, we isolated a microbial strain with high emulsification and petroleum hydrocarbon degradation efficiency of diesel fuel in culture. The efficacy of the isolated microbial strain, identified as Candida catenulata CM1, was further evaluated during composting of a mixture containing 23% food waste and 77% diesel-contaminated soil including 2% (w/w) diesel. After 13 days of composting, 84% of the initial petroleum hydrocarbon was degraded in composting mixes containing a powdered form of CM1 (CM1-solid), compared with 48% of removal ratio in control reactor without inoculum. This finding suggests that CM1 is a viable microbial strain for bioremediation of oil-contaminated soil with food waste through composting processes. - Enhancement on degradation ability of petroleum hydrocarbon by the microbial strain in the composting process with food waste

Determining the better solvent and time for extracting soil by soxhlet in TPH (Total Petroleum Hydrocarbon) gravimetric method; A determinacao de qual o melhor solvente e o melhor tempo de extracao de sedimento em aparato Soxhlet na metodologia do TPH (Total Petroleum Hydrocarbon) gravimetrico

Energy Technology Data Exchange (ETDEWEB)

Koike, Renato S.; Lima, Guilherme; Baisch, Paulo R. [Fundacao Universidade Federal do Rio Grande (FURG), RS (Brazil)

2004-07-01

There are several methods of TPH (Total Petroleum Hydrocarbons) analysis of petroleum hydrocarbons contaminants in sediment. The TPH gravimetric has been widely used in many studies and in oil spill monitoring case. The present work examined three different solvents (DCM, DCM/N-HEX and N-HEX), in three different times, to the purpose to optimize the contaminants extraction using USEPA 9071 and 3540 reference method. Then was realized analysis of Total Organic Carbon (TOC) for monitoring the reproducible extracts. The sediments used in this experiment was collected in the Cavalos Island, localized in the city of Rio Grande, RS-Brasil. The sediment was 'washed' and after then contaminated with petroleum. The extracts were realized in Soxhlet apparatus, in three different times (4, 8 and 12 hours), and TOC analysis were realized before and after the extraction. The result demonstrated that eight hours with DCM/N-HEX solvent is more indicated for TPH gravimetric in sediment analysis with high concentration of petroleum hydrocarbons. TOC analysis demonstrated inappropriate for monitoring extract reproducibility. (author)

Evaluation of clean-up agents for total petroleum hydrocarbon analysis in biota and sediments.

NARCIS (Netherlands)

Muijs, B.; Jonker, M.T.O.

2009-01-01

Petroleum hydrocarbons (oil) are common environmental contaminants. For risk assessment purposes, their concentrations in environmental matrixes, such as biota and soils/sediments are frequently determined by solvent extraction and subsequent analysis with gas chromatography (GC) equipped with flame

Reuse of solid petroleum waste in the manufacture of porcelain stoneware tile.

Science.gov (United States)

Pinheiro, B C A; Holanda, J N F

2013-03-30

This study investigates the incorporation of solid petroleum waste as raw material into a porcelain stoneware tile body, in replacement to natural kaolin material by up to 5 wt.%. Tile formulations containing solid petroleum waste were pressed and fired at 1240 °C by using a fast-firing cycle. The tile pieces were tested to determine their properties (linear shrinkage, water absorption, apparent density, and flexural strength), sintered microstructure, and leaching toxicity. The results therefore indicated that the growing addition of solid petroleum waste into tile formulations leads to a decrease of linear shrinkage, apparent density, and flexural strength, and to an increase of water absorption of the produced tile materials. It was also found that the replacement of kaolin with solid petroleum waste, in the range up to 2.5 wt.%, allows the production of porcelain stoneware tile (group BIa, ISO 13006 standard). All concentrations of Ag, As, Ba, Cd, Cr (total), Hg, and Pb of the fired porcelain stoneware tile pieces in the leachate comply with the current regulatory limits. These results indicate that the solid petroleum waste could be used for high-quality porcelain stoneware tile production, thus giving rise to a new possibility for an environmentally friendly management of this abundant waste. Copyright © 2013 Elsevier Ltd. All rights reserved.

Microbial degradation of petroleum hydrocarbons in estuarine sediment of Tama River in Tokyo urban area

International Nuclear Information System (INIS)

Yamane, Akiko; Hosomi, Masaaki; Murakami, Akihiko; Sakakibara, Koji

1997-01-01

Aerobic and anaerobic biodegradation rates of petroleum hydrocarbons, i.e., hexadecane (HEX), phenanthrene (PHE), and anthracene (ANT), were determined in estuarine sediment of the Tama River in urban Tokyo, followed by estimating their respective degradation potential. While in a sediment slurry, the aerobic biodegradation rates of these petroleum hydrocarbons ranged from 40 to 70 μg.g -1 dry sediment:day -1 . The anaerobic biodegradation rate of HEX was found to be 5 -8 μg.g -1 dry sediment.day -1 , whereas that of PHE and ANT could not be detected following a 2-month incubation. Aerobic degradation of HEX was not affected by coexistence with either PHE or ANT, nor by the salinity level. The number of HEX-, PHE-, or ANT-utilizing bacteria ranged from 5 - 10% of the total number of aerobic heterotrophic bacteria. We calculated their biodegradation potentials using the biomass of naturally existing petroleum hydrocarbon utilizing bacteria present in the sampled sediment, with results for HEX, PHE, and ANT being 1.0 -3.5, 4.2 x 10 -2 , and 1.2 x 10 -2 -9.4 x 10 -1 μg.g -1 dry sediment day -1 , respectively. In the aerobic tidal sediment of the Tama River, the purification potentials of HEX, PHE, and ANT were assessed to be approximately equal to their accumulation potentials occurring at the normal water level. (Author)

Subsurface migration of petroleum hydrocarbons: A case study of immiscible migration and chromatographic separation

International Nuclear Information System (INIS)

Dawson, H.E.

1991-01-01

The subsurface distribution of a leaked crude oil illustrates the combined influence of both the chemical and physical properties of soil and free product on the migration of petroleum hydrocarbons. Immiscible phase behavior was observed, as well as chromatographic-like separation of the lighter constituents of the crude oil from the heavier constituents. After downward migration through approximately 50 ft of unsaturated, heterogeneous alluvial sediments, the crude oil formed a horizontal plume on top of a perched, saturated zone. Immiscible phase trapping is evident from the occurrence of very high concentration of hydrocarbons in both the vertical and horizontal plumes. Samples taken from the vertical zone of contamination indicate a transition from heavier hydrocarbons near the surface to lighter hydrocarbons at depth. This phenomenon is attributed to chromatographic-like separation of the heavier hydrocarbons by the soil, possibly due to preferential solubility of the lighter hydrocarbons in percolating ran water

Remediation of petroleum hydrocarbons by inoculation with laboratory-cultured microorganisms

International Nuclear Information System (INIS)

Maxwell, C.R.; Baqai, H.A.

1995-01-01

An unauthorized release of gasoline from an underground storage tank (UST) impacted the soil and groundwater beneath a maintenance and fueling capacity. The property owner attempted to remediate the site by inoculating wells screened within the unsaturated and saturated zones with laboratory-cultured microorganisms. The inoculation was a one-time event. No nutrients were added to the subsurface. Air was injected into all inoculation wells during the project to promote aerobic microbial activity. At the first groundwater sampling event after inoculation, concentrations of petroleum hydrocarbon constituents increased inoculation wells. Measurements of dissolved oxygen in the groundwater appeared to indicate that oxygen consumption, and thus hydrocarbon degradation, was not occurring. Visual and olfactory evidence of the groundwater indicated evidence of decaying organic matter. After approximately 1 year and a thorough purging of the inoculation wells, decaying matter disappeared and dissolved oxygen and hydrocarbon concentrations generally returned to preproject levels. Further contaminant reduction did not occur, indicating temporary degradation of water quality as a result of the project and unsuccessful remediation

Evaluating the utility of hydrocarbons for Re-Os geochronology : establishing the timing of processes in petroleum ore systems

Energy Technology Data Exchange (ETDEWEB)

Selby, D.; Creaser, R.A. [Alberta Univ., Edmonton, AB (Canada). Dept. of Earth and Atmospheric Sciences

2005-07-01

Oil from 6 Alberta oil sands deposits were analyzed with a rhenium-osmium (Re-Os) isotope chronometer, an emerging tool for determining valuable age information on the timing of petroleum generation and migration. The tool uses molybdenite and other sulphide minerals to establish the timing and duration of mineralization. However, establishing the timing events of petroleum systems can be problematic because viable sulphides for the Re-Os chronometer are often not available. Therefore, the known presence of Re and Os associated with organic matter in black shale, a common source of hydrocarbons, may suggest that bitumen and petroleum common to petroleum systems may be utilised for Re-Os geochronology. This study evaluated the potential of the Re-Os isotopic system for geochronology and as an isotopic tracer for hydrocarbon systems. The evaluation was based on Re-Os isotopic analyses of bitumen and oil sands. Hydrocarbons formed from migrated oil in both Alberta oil sand deposits and a Paleozoic Mississippi Valley-type lead-zinc deposit contain significant Re and Os contents with high {sup 187}Re/{sup 188}Os and radiogenic {sup 187}Os/{sup 188}Os ratios suitable for geochronology. The oil from the 6 Alberta oil sand deposits yields Re-Os analyses with very high Re/{sup 188}Os ratios, and radiogenic Os isotopic compositions. Regression of the Re-Os data yields a date of 116 {+-} 27 Ma. This date plausibly represents the period of in situ radiogenic growth of {sup 187}Os following hydrocarbon migration and reservoir filling. Therefore, directly dating these processes, and this formation age corresponds with recent burial history models for parts of the Western Canada Sedimentary Basin. The very high initial {sup 187}Os/{sup 188}Os for this regression requires rocks much older than Cretaceous for the hydrocarbon source.

Environmental impact of petroleum products in the soil. Part II: Petroleum products composition and key properties

International Nuclear Information System (INIS)

Zerlia, T.

2001-01-01

The fate of petroleum hydrocarbons in the soil depends on the chemical-physic properties of each hydrocarbon, as well as on the soil characteristics. The mean composition of various petroleum products, the key chemical compounds and their characteristics are focused in order to outline the environmental behaviour of petroleum hydrocarbons in the soil [it

Bioremediation of petroleum hydrocarbons in soil: Activated sludge treatability study

International Nuclear Information System (INIS)

Rue-Van Es, J.E. La.

1993-05-01

Batch activated sludge treatability studies utilizing petroleum hydrocarbon contaminated soils (diesel oil and leaded gasoline) were conducted to determine: initial indigenous biological activity in hydrocarbon-contaminated soils; limiting factors of microbiological growth by investigating nutrient addition, chemical emulsifiers, and co-substrate; acclimation of indigenous population of microorganisms to utilize hydrocarbons as sole carbon source; and temperature effects. Soil samples were taken from three different contaminated sites and sequencing batch reactors were run. Substrate (diesel fuel) and nutrient were added as determined by laboratory analysis of orthophosphate, ammonia nitrogen, chemical oxygen demand, and total organic carbon. Substrate was made available to the bacterial mass by experimenting with four different chemical emulsifiers. Indigenous microorganisms capable of biotransforming hydrocarbons seem to be present in all the contaminated soil samples received from all sites. Microscopic analysis revealed no visible activity at the beginning of the study and presence of flagellated protozoa, paramecium, rotifers, and nematodes at the end of the year. Nutrient requirements and the limiting factors in microorganism growth were determined for each site. An emulsifier was initially necessary to make the substrate available to the microbial population. Decreases in removal were found with lowered temperature. Removal efficiencies ranged from 50-90%. 95 refs., 11 figs., 13 tabs

Bioremediation of petroleum hydrocarbons in soil: Activated sludge treatability study

Energy Technology Data Exchange (ETDEWEB)

Rue-Van Es, J.E. La.

1993-05-01

Batch activated sludge treatability studies utilizing petroleum hydrocarbon contaminated soils (diesel oil and leaded gasoline) were conducted to determine: initial indigenous biological activity in hydrocarbon-contaminated soils; limiting factors of microbiological growth by investigating nutrient addition, chemical emulsifiers, and co-substrate; acclimation of indigenous population of microorganisms to utilize hydrocarbons as sole carbon source; and temperature effects. Soil samples were taken from three different contaminated sites and sequencing batch reactors were run. Substrate (diesel fuel) and nutrient were added as determined by laboratory analysis of orthophosphate, ammonia nitrogen, chemical oxygen demand, and total organic carbon. Substrate was made available to the bacterial mass by experimenting with four different chemical emulsifiers. Indigenous microorganisms capable of biotransforming hydrocarbons seem to be present in all the contaminated soil samples received from all sites. Microscopic analysis revealed no visible activity at the beginning of the study and presence of flagellated protozoa, paramecium, rotifers, and nematodes at the end of the year. Nutrient requirements and the limiting factors in microorganism growth were determined for each site. An emulsifier was initially necessary to make the substrate available to the microbial population. Decreases in removal were found with lowered temperature. Removal efficiencies ranged from 50-90%. 95 refs., 11 figs., 13 tabs.

Environmental magnetic and petroleum hydrocarbons records in sediment cores from the north east coast of Tamilnadu, Bay of Bengal, India.

Science.gov (United States)

Venkatachalapathy, R; Veerasingam, S; Basavaiah, N; Ramkumar, T; Deenadayalan, K

2011-04-01

In this study, mineral magnetic properties and petroleum hydrocarbons were statistically analysed in four sediment cores (C1, A1, T1 and K1) from the north east coast of Tamilnadu, India to examine the feasibility of PHC concentrations assessment using magnetic susceptibility. The C1 and A1 cores reveal a clear horizon of increase in PHC above 35 and 50 cm respectively suggesting the excess anthropogenic loading occurred in the recent past. Magnetic properties which were enhanced in the upper part of the sediment cores were the result of ferrimagnetic minerals from anthropogenic sources. Factor analysis confirmed that the input of magnetic minerals and petroleum hydrocarbons in Chennai coastal sediments are derived from the same sources. The present study shows that instead of expensive and destructive PHC chemical methods, magnetic susceptibility is found to be a suitable, cheap and rapid method for detailed study of petroleum hydrocarbon contamination in marine sediments. Copyright © 2011 Elsevier Ltd. All rights reserved.

CBOS damage assessment on Pacific herring - Toxicity of petroleum hydrocarbons (PAHs) to fish early life stages

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Ecotox Program is at the forefront, nationally and internationally, of targeted research to characterize the impacts of petroleum hydrocarbons on NOAA trust...

DWH damage assessment on marine species - Toxicity of petroleum hydrocarbons (PAHs) to fish early life stages

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Ecotox Program is at the forefront, nationally and internationally, of targeted research to characterize the impacts of petroleum hydrocarbons on NOAA trust...

Succession of Hydrocarbon Degradation and Microbial Diversity during a Simulated Petroleum Seepage in Caspian Sea Sediments

Science.gov (United States)

Mishra, S.; Stagars, M.; Wefers, P.; Schmidt, M.; Knittel, K.; Krueger, M.; Leifer, I.; Treude, T.

2016-02-01

Microbial degradation of petroleum was investigated in intact sediment cores of Caspian Sea during a simulated petroleum seepage using a sediment-oil-flow-through (SOFT) system. Over the course of the SOFT experiment (190 days), distinct redox zones established and evolved in the sediment core. Methanogenesis and sulfate reduction were identified to be important processes in the anaerobic degradation of hydrocarbons. C1 to C6 n-alkanes were completely exhausted in the sulfate-reducing zone and some higher alkanes decreased during the upward migration of petroleum. A diversity of sulfate-reducing bacteria was identified by 16s rRNA phylogenetic studies, some of which are associated with marine seeps and petroleum degradation. The δ13C signal of produced methane decreased from -33.7‰ to -49.5‰ indicating crude oil degradation by methanogenesis, which was supported by enrichment culturing of methanogens with petroleum hydrocarbons and presence of methanogenic archaea. The SOFT system is, to the best of our knowledge, the first system that simulates an oil-seep like condition and enables live monitoring of biogeochemical changes within a sediment core during petroleum seepage. During our presentation we will compare the Caspian Sea data with other sediments we studied using the SOFT system from sites such as Santa Barbara (Pacific Ocean), the North Alex Mud Volcano (Mediterranean Sea) and the Eckernfoerde Bay (Baltic Sea). This research was funded by the Deutsche Forschungsgemeinschaft (SPP 1319) and DEA Deutsche Erdoel AG. Further support came from the Helmholtz and Max Planck Gesellschaft.

Identification of petroleum hydrocarbons using a reduced number of PAHs selected by Procrustes rotation.

Science.gov (United States)

Fernández-Varela, R; Andrade, J M; Muniategui, S; Prada, D; Ramírez-Villalobos, F

2010-04-01

Identifying petroleum-related products released into the environment is a complex and difficult task. To achieve this, polycyclic aromatic hydrocarbons (PAHs) are of outstanding importance nowadays. Despite traditional quantitative fingerprinting uses straightforward univariate statistical analyses to differentiate among oils and to assess their sources, a multivariate strategy based on Procrustes rotation (PR) was applied in this paper. The aim of PR is to select a reduced subset of PAHs still capable of performing a satisfactory identification of petroleum-related hydrocarbons. PR selected two subsets of three (C(2)-naphthalene, C(2)-dibenzothiophene and C(2)-phenanthrene) and five (C(1)-decahidronaphthalene, naphthalene, C(2)-phenanthrene, C(3)-phenanthrene and C(2)-fluoranthene) PAHs for each of the two datasets studied here. The classification abilities of each subset of PAHs were tested using principal components analysis, hierarchical cluster analysis and Kohonen neural networks and it was demonstrated that they unraveled the same patterns as the overall set of PAHs. (c) 2009 Elsevier Ltd. All rights reserved.

Petroleum hydrocarbons in sediment from the northern Gulf of Mexico shoreline, Texas to Florida

Science.gov (United States)

Rosenbauer, Robert J.; Campbell, Pamela L.; Lam, Angela; Lorenson, T.D.; Hostettler, Frances D.; Thomas, Burt; Wong, Florence L.

2011-01-01

Petroleum hydrocarbons were extracted and analyzed from shoreline sediment collected from the northern Gulf of Mexico (nGOM) coastline that could potentially be impacted by Macondo-1 (M-1) well oil. Sediment was collected before M-1 well oil made significant local landfall and analyzed for baseline conditions by a suite of diagnostic petroleum biomarkers. Oil residue in trace quantities was detected in 45 of 69 samples. With the aid of multivariate statistical analysis, three different oil groups, based on biomarker similarity, were identified that were distributed geographically along the nGOM from Texas to Florida. None of the sediment hydrocarbon extracts correlated with the M-1 well oil extract, however, the similarity of tarballs collected at one site (FL-18) with the M-1 well oil suggests that some oil from the Deepwater Horizon spill may have been transported to this site in the Florida Keys, perhaps by a loop current, before that site was sampled.

Biodegradation Of Polycyclic Aromatic Hydrocarbons In Petroleum Oil Contaminating The Environment

International Nuclear Information System (INIS)

Partila, A.M.

2013-01-01

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous pollutants in urban atmospheres (Chen et al., 2013). PAHs enter the environment via incomplete combustion of fossil fuels and accidental leakage of petroleum products, and as components of products such as creosote (Muckian et al., 2009). Due to PAHs carcinogenic activity, they have been included in the European Union (EU) and the Environmental Protection Agency (EPA) priority pollutant lists. Human exposure to PAHs occurs in three ways, inhalation, dermal contact and consumption of contaminated foods, which account for 88-98% of such contamination; in other words, diet is the major source of human exposure to these contaminants (Rey-Salgueiro et al., 2008). Both the World Health Organization and the UK Expert Panel on Air Quality Standards (EPAQS) have considered benzo(a)pyrene (BaP) as a marker of the carcinogenic potency of the polycyclic aromatic hydrocarbons (PAH) mixture (Delgado-Saborit et al., 2011). Polycyclic aromatic and heavier aliphatic hydrocarbons, which have a stable recalcitrant molecular structure, exhibit high hydrophobicity and low aqueous solubility, are not readily removed from soil through leaching and volatilization (Brassington et al., 2007). The hydrophobicity of PAHs limits desorption to the aqueous phase (Donlon et al., 2002). Six main ways of dissipation, i.e. disappearance, are recognized in the environment: volatilization, photooxidation, Aim of the Work chemical oxidation, sorption, leaching and biodegradation. Microbial degradation is considered to be the main process involved in the dissipation of PAH (Yuan et al., 2002). Thus, more and more research interests are turning to the biodegradation of PAHs. Some microorganisms can utilize PAHs as a source of carbon and energy so that PAHs can be degraded to carbon dioxide and water, or transformed to other nontoxic or low-toxic substances (Perelo, 2010). Compared with other physical and chemical methods such as combustion

Management of the solid waste in perforation projects exploratory hydrocarbons

International Nuclear Information System (INIS)

Rodriguez Miranda, J.P.

2010-01-01

This paper describes de considerations for solid waste management in hydrocarbons exploration projects, as the serious environmental affectation as a function of soil contamination by leachate form the temporary storage of contaminated industrial waste hydrocarbons, altered by the presence of deposits landscaping waste materials, pollution of water and vegetation and the production of odors.

A combined approach of physicochemical and biological methods for the characterization of petroleum hydrocarbon-contaminated soil.

Science.gov (United States)

Masakorala, Kanaji; Yao, Jun; Chandankere, Radhika; Liu, Haijun; Liu, Wenjuan; Cai, Minmin; Choi, Martin M F

2014-01-01

Main physicochemical and microbiological parameters of collected petroleum-contaminated soils with different degrees of contamination from DaGang oil field (southeast of Tianjin, northeast China) were comparatively analyzed in order to assess the influence of petroleum contaminants on the physicochemical and microbiological properties of soil. An integration of microcalorimetric technique with urease enzyme analysis was used with the aim to assess a general status of soil metabolism and the potential availability of nitrogen nutrient in soils stressed by petroleum-derived contaminants. The total petroleum hydrocarbon (TPH) content of contaminated soils varied from 752.3 to 29,114 mg kg(−1). Although the studied physicochemical and biological parameters showed variations dependent on TPH content, the correlation matrix showed also highly significant correlation coefficients among parameters, suggesting their utility in describing a complex matrix such as soil even in the presence of a high level of contaminants. The microcalorimetric measures gave evidence of microbial adaptation under highest TPH concentration; this would help in assessing the potential of a polluted soil to promote self-degradation of oil-derived hydrocarbon under natural or assisted remediation. The results highlighted the importance of the application of combined approach in the study of those parameters driving the soil amelioration and bioremediation.

Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

1994-12-31

With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

Information processing to determine waste minimization/pollution prevention strategies in the petroleum industry

Energy Technology Data Exchange (ETDEWEB)

Falcon, Mariali F. de [CORPOVEN, S.A. (Venezuela)

1993-12-31

With the passage of the 1984 Hazardous and Solid Waste Amendments to the Resource Conservation and Recovery Act in the United States, industries, and particularly the petroleum industry, have become more interested in their waste management practices. This works aims to present a methodology to organize the collected data concerning waste minimization and, or, pollution prevention in the petroleum industry into a bibliographic database

The reduction of petroleum hydrocarbons in soil under saline conditions using ultrasound

Energy Technology Data Exchange (ETDEWEB)

McMillan, D. [SNC-Lavallin, Vancouver, BC (Canada); Northern British Columbia Univ., Prince George, BC (Canada)

2010-07-01

Petroleum hydrocarbons (PHCs) and salts are two of the most common soil contaminants found at oil and gas extraction sites. High concentrations of salt from brine spills may amplify the challenges of soil remediation by reducing bioavailability for remediation. This PowerPoint presentation described an ultrasonic soil flushing technology that used sonic cavitation to break down contaminants. Long chain and aromatic hydrocarbons with complex structures were broken down by the direct oxidation under high temperature and pressure environments created by the sonic cavitation process. The cavitation waves broke up the aggregates of solid particles and increased the turbulence and transportation of the contaminants. A laboratory study evaluated the ability of the treatment process to remediate salt and hydrocarbon contaminated soil samples. The adsorption isotherms of the samples were analyzed. Sand, clay, and muskeg samples were treated. Results of the study suggested that the treatment is more effective when treating granular soils with high hydraulic conductivity. Even small amounts of salt were found to have a negative impact on the reduction of hydrocarbon contaminants. tabs., figs.

Development and application of techniques for monitoring the bioremediation of petroleum hydrocarbon-contaminated soils

International Nuclear Information System (INIS)

Greer, C.; Hawar, J.; Samson, R.

1994-01-01

A series of tests was designed to examine bioremediation potential in soil and to monitor performance during the treatment operation. Physical and chemical characterization of the soil provides information on the types of organics, their concentrations, and whether interfering materials are present. Microbiological assessment involves culturing of bacterial populations in the soil and examination of the colonies to determine which have the genetic potential to degrade the soil contaminants. Catabolic gene probes are used to survey viable bacteria from petroleum hydrocarbon contaminated soils. Such soils consistently demonstrate the presence of bacteria possessing the genetic capability to degrade simple straight-chain alkanes and aromatics. Mineralization and respirometric studies are indicators of the biological activity in the soil, and can be directed at microbial activity towards specific substrates. Gene probe monitoring of a petroleum hydrocarbon contaminated soil during biopile treatment demonstrated that hydrocarbon-degrading bacterial numbers and activity were temperature dependent. The results showed that the activity of the indigenous bacteria as measured by hexadecane mineralization also correlated with the disappearance of the oil and grease. The application of this protocol has provided a useful means to screen contaminated soils for bacteria with desirable catabolic properties and to monitor pollutant-degrading bacteria during biotreatment. 15 refs., 10 figs

Oil characterisation: assessment of composition, risks, degradation and remediation potential of total petroleum hydrocarbons in soil

International Nuclear Information System (INIS)

Lookman, R.; Vanermen, G.; Van De Weghe, H.; Gemoets, J.; Van der Sterren, G.; Alphenaar, A.

2005-01-01

Several methods are available for the characterization of petroleum hydrocarbons. The TPHCWG (Total Petroleum Hydrocarbon Criteria Working Group) developed a method based on a silica column separation of aromatics and aliphatics and a GC-FID subdivision into equivalent-carbon fractions (EC) ('TPH-method'). This method was mainly developed for assessing human risks of oil compounds. Within NOBIS (Dutch Research program Biological In-situ Remediation), another method was developed based upon an equilibrium-experiment of the oil-polluted soil with water (column recirculation), which was further developed by TTE ('TTE-method'). This method uses measured water solubilities of individual oil components and GC-retention times yielding a subdivision of the hydrocarbons into compound classes that are relevant for assessing the remediation potential of the specific oil pollution. In this paper we present results of a research project in which we developed a new method, the 'OK-method' that combines these two procedures and allows a complete characterisation of the oil in terms of composition, (human) risks, volatility, solubility, plume behaviour (migration velocities of the soluble components) and aerobic degradation potential. (authors)

Removal of polycyclic aromatic hydrocarbons from organic solvents by ashes wastes

Energy Technology Data Exchange (ETDEWEB)

Perez-Gregorio, M.R.; Garcia-Falcon, M.S.; Martinez-Carballo, E. [Nutrition and Bromatology Group, Analytical and Food Chemistry Department, Faculty of Food Science and Technology, University of Vigo, Ourense Campus, E32004 Ourense (Spain); Simal-Gandara, J., E-mail: jsimal@uvigo.es [Nutrition and Bromatology Group, Analytical and Food Chemistry Department, Faculty of Food Science and Technology, University of Vigo, Ourense Campus, E32004 Ourense (Spain)

2010-06-15

Polycyclic aromatic hydrocarbons (PAHs) can be formed during the refinery processes of crude petroleum. Their removal is of great importance. The same happens with other organic solvents used for the extraction of PAHs (hexane, acetonitrile...), which can be polluted with PAHs. Kinetic and equilibrium batch sorption tests were used to investigate the effect of wood ashes wastes as compared to activated carbon on the sorption of three representative PAHs from n-hexane and acetonitrile. Mussel shell ashes were discarded for batch sorption experiments because they were the only ashes containing PAHs. The equilibrium time was reached at 16 h. Physical sorption caused by the aromatic nature of the compounds was the main mechanism that governed the PAHs removal process. Our investigation revealed that wood ashes obtained at lower temperature (300 deg. C) did not show any PAHs sorption, while ashes obtained at higher temperature (>500 deg. C) have adsorbent sites readily available for the PAH molecules. An increase in the molecular weight of PAHs has a strong effect on sorption wood ashes wastes. As low the wood ashes particle size as high the sorption of PAHs, as a result of differences in adsorbent sites. The performance of wood ash wastes vs. activated carbon to remove 10 PAHs from organic solvents is competitive in price, and a good way for waste disposal.

The Amoco CadizOil Spill: Evolution of Petroleum Hydrocarbons in the Ile Grande Salt Marshes (Brittany) after a 13-year Period

Science.gov (United States)

Mille, G.; Munoz, D.; Jacquot, F.; Rivet, L.; Bertrand, J.-C.

1998-11-01

The Ile Grande salt marshes (Brittany coast) were polluted by petroleum hydrocarbons after theAmoco Cadizgrounding in 1978. Thirteen years after the oil spill, sediments were analysed for residual hydrocarbons in order to monitor the aliphatic and aromatic hydrocarbon signatures and to assess both qualitatively and quantitatively the changes in composition of theAmoco Cadizoil. Six stations were selected in the Ile Grande salt marshes and sediments were sampled to a depth of 20 cm. For each sample, the hydrocarbon compositions were determined for alkanes, alkenes, aromatics and biomarkers (terpanes, steranes, diasteranes). Hydrocarbon levels drastically decreased between 1978 and 1991, but to different extents according to the initial degree of contamination. In 1991, hydrocarbon concentrations never exceeded 1·7 g kg-1sediment dry weight, and in most cases were less than 0·1 g kg-1sediment dry weight. Even though petroleum hydrocarbons are still present, natural hydrocarbons were also detected at several stations. Changes in some biomarker distributions were observed 13 years after the oil spill. Nevertheless, most of the biomarkers are very stable in the salt marsh environment and remain unaltered even after a 13-year period.

Desulfurization of waste gases of the incinerator after petroleum refining

International Nuclear Information System (INIS)

Samesova, D.; Ladomersky, J.

2001-01-01

Desulfurization of waste gases of the incinerator after petroleum refining was developed. Mixing of wastes with lime (10% of additive of total volume of waste) was proved before introduction into incinerator. Concentrations of CO, CO 2 , O 2 , NO 2 , SO 2 and temperature of combustion products were measured by automatic analyser

Dissolved petroleum hydrocarbons along the oil tanker route in the southern Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Topgi, R; Noronha, R; Fondekar, S.P.; SenGupta, R

Concentrations of dissolved petroleum hydrocarbons during 3 cruises (Nos. 51, 66 and 68) of R V Gaveshani, along the oil tanker route, in the southern Bay of Bengal at 0, 10 and 20 m were 19.95 + or - 3.38, 16.78 + or - 2.53 and 13.45 + or - 2.17 mu...

Pyrolysis of municipal plastic wastes for recovery of gasoline-range hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Demirbas, Ayhan [Department of Chemical Engineering, Selcuk University, Konya (Turkey)

2004-08-01

This paper describes non-catalytic pyrolysis of plastic waste materials. Three types of waste plastics were used in this study: polystyrene (PS), polyethylene (PE) and polypropylene (PP). Under pyrolysis conditions, plastic wastes can be decomposed into three fractions: gas, liquid and solid residue. The liquid products are usually composed of higher boiling point hydrocarbons. In order to obtain useful gasoline-range hydrocarbons from the pyrolytic oil, fractional distillation is preferred for product separation. More valuable chemical raw materials including benzene, toluene and other condensed aromatic hydrocarbons may be obtained by refining the pyrolytic oil. The results showed that waste PS yielded higher liquid, and waste PE and PP yielded higher gaseous products. The dominant pyrolytic liquid product of PS waste was styrene.

Proceedings of Conference on Hydrocarbon Contaminated Soils (3rd) Held in Amherst, Massachusetts on September 1989 (Petroleum Contaminated Soils. Volume 3)

Science.gov (United States)

1990-10-01

degraders (105 to 106). After exposure to petroleum hydrocarbons, the microbial ecology of the soil adjusts so that the number of petroleum degraders...34 in R. M. Atlas , ed., Petroleum Microbiology (Macmillan Pub- lishing Co., Inc., 1984). 3. Bossert, I., and R. Bartha . "The Fate of Petroleum in Soil...and nature of the microbial population. I For instance, the soil class (i.e., dominant grain size or grade) may help the health assessor determine

The method of purification of waste water of NPS from petroleum oil using UV-radiation

International Nuclear Information System (INIS)

Kulemin, V.V.; Kareta, V.I.

1993-01-01

The main methods of concentration and purification of radioactive waste water of russian NPS are distillation and ion exchange. When waste water containing petroleum oil and washing matter is distillated, part of petroleum and washing matters go to the condensate. The purification of this condensate leads to pollution of ion exchange resins by petroleum oil and reduction of the filter cycle number. The purification of condensate of Russian NPS from petroleum oil is carried out using active carbon and polymer filters, but this process is not effective and fails to give pure condensate. Therefore, the authors began to search for more effective methods of purification of waste water from petroleum oil. They found that UV-radiation makes it possible to purify water from petroleum matter to concentration of the organic phase less than 0.5 mg/dm3. In this process of purification the air, contained in the water phase, was used as an oxidant. When purification is carried out in the absence of sorbents, the quantity of radioactive solid waste, which have to be recovered, decreases. During the study of purification of waste water it was found that increasing of the temperature of the process increases the rate of UV-radiation-induced oxidation of organic phase. The increase in the initial concentration of petroleum products also increases the rate of petroleum oil decomposition. The content of ions in water phase decreases the purification rate. The investigations were carried out on the laboratory scale with water and condensate from Tver's NPS

Biochemical ripening of dredged sediments. Part 2. Degradation of polycyclic aromatic hydrocarbons and total petroleum hydorcarbons in slurried and consolidated sediments

NARCIS (Netherlands)

Vermeulen, J.; Gool, van M.P.M.; Mentink, G.H.; Joziasse, J.; Bruning, H.; Grotenhuis, J.T.C.

2007-01-01

Ripening of polycyclic aromatic hydrocarbons (PAH) and total petroleum hydrocarbons (TPH) polluted dredged sediment can be considered as a bioremediation technique. Aerobic biodegradation of PAH and TPH was studied in five previously anaerobic-slurried sediments during a 350-d laboratory incubation

Pollution by petroleum hydrocarbons in sediments from continental shelf of Tabasco State, Mexico

International Nuclear Information System (INIS)

Botello, A.V.; Gonzalez, C.; Diaz, G.

1991-01-01

The Wider Caribbean is potentially one of the largest oil producing areas in the world. Major petroleum production areas include Louisiana and Texas, USA; the Bay of Campeche, Mexico; Lake Maracaibo, Venezuela; and Gulf of Paria, Trinidad; all of which are classified as production accident high-risk zones. About 5 million of barrels are transported every day in the Caribbean, thus generating an intense tanker traffic. It has been estimated that oil discharges from tank washings within the Wider Caribbean could be as high as 7 million barrels/year. For all those reasons petroleum pollution is considered as the major environmental problem in the Wider Caribbean area and increasing day to day due to the use of petroleum as the main energy source. On the other hand, the continental shelf of Tabasco state actually represents one of the most productive areas for crude oil in the Gulf of Mexico. Sediments were collected from this area and analyzed for hydrocarbons

Distribution and Fractional Composition of Petroleum Hydrocarbons in Roadside Soils

Directory of Open Access Journals (Sweden)

Larysa Mykhailova

2013-01-01

Full Text Available Total petroleum hydrocarbon (TPH concentrations and their fractional composition (medium fraction: n-alkane chain-length C15 to C27, heavy fraction: >C27 were determined at distances from 1 to 60 m from roads and at soil depths from 0.5 to 15 cm. The traffic intensities were up to 25000 vehicles per day. Soil TPH concentrations were highest within 15 m distance (665 and 3198 mg kg−1 at the windward and leeward sides, resp., followed by a rapid drop to background values beyond (196 and 115 mg kg−1 in 60 m distance at the windward and leeward sides, resp.. The data variability was lowest at distances of 1 m and highest within tree plantations at distances of 15 m from the road. The TPH concentrations decreased with depth but were significantly higher than the background at all depths investigated. A principal component analysis revealed a positive relation between the medium-to-heavy fraction ratio and soil depth. A fractional differentiation of hydrocarbons with distance from road was not observed. It was concluded that the assessment of the potential of hydrocarbons to translocate, accumulate, or degrade in soil necessitates their subdivision into fractions based on their physicochemical and metabolic properties.

Oil characterisation: assessment of composition, risks, degradation and remediation potential of total petroleum hydrocarbons in soil

Energy Technology Data Exchange (ETDEWEB)

Lookman, R.; Vanermen, G.; Van De Weghe, H.; Gemoets, J. [Vito, Mol (Belgium); Van der Sterren, G.; Alphenaar, A. [TTE, Deventer (Netherlands)

2005-07-01

Several methods are available for the characterization of petroleum hydrocarbons. The TPHCWG (Total Petroleum Hydrocarbon Criteria Working Group) developed a method based on a silica column separation of aromatics and aliphatics and a GC-FID subdivision into equivalent-carbon fractions (EC) ('TPH-method'). This method was mainly developed for assessing human risks of oil compounds. Within NOBIS (Dutch Research program Biological In-situ Remediation), another method was developed based upon an equilibrium-experiment of the oil-polluted soil with water (column recirculation), which was further developed by TTE ('TTE-method'). This method uses measured water solubilities of individual oil components and GC-retention times yielding a subdivision of the hydrocarbons into compound classes that are relevant for assessing the remediation potential of the specific oil pollution. In this paper we present results of a research project in which we developed a new method, the 'OK-method' that combines these two procedures and allows a complete characterisation of the oil in terms of composition, (human) risks, volatility, solubility, plume behaviour (migration velocities of the soluble components) and aerobic degradation potential. (authors)

Biodegradation and Bioremediation of Petroleum Pollutants in Soil

Energy Technology Data Exchange (ETDEWEB)

Huesemann, Michael H.

2004-08-02

During bioremediation, petroleum hydrocarbons are converted by naturally occurring or indigenous soil microorganisms to carbon dioxide, water, bacterial cells (biomass), and humic materials. Numerous factors are known to affect both the rate and the extent of hydrocarbon biodegradation in contaminated soils. These include soil properties such as moisture content, aeration, nutrient status, pH, and temperature as well as waste characteristics such as the concentration and molecular structure of hydrocarbon compounds or classes, the presence of inhibitors and cometabolic substrates, and the degree of contaminant sequestration which often leads to serious bioavailability limitations, particularly in aged soils. It is the objective of this chapter to outline a strategy for optimizing the hydrocarbon bioremediation process by adjusting the various operational parameters so that none of them become a limiting factor during treatment.

Tainting by short-term exposure of Atlantic salmon to water soluble petroleum hydrocarbons

International Nuclear Information System (INIS)

Ackman, R.G.; Heras, H.

1992-01-01

Experiments were conducted to examine the extent of tainting of salmon by exposure to the soluble fraction of petroleum hydrocarbons. The experiments were conducted on Atlantic salmon in tanks containing seawater artificially contaminated at three different concentrations with the soluble fraction of a North Sea crude. The salmon flesh was analyzed by gas chromatography and taste tests were conducted on cooked salmon samples to determine the extent of tainting. Salmon in control tanks with uncontaminated seawater had muscle accumulations of total hydrocarbons of ca 1 ppM. The muscle accumulations of total hydrocarbons in the salmon were 13.5 ppM, 25.6 ppM, and 31.3 ppM for water soluble fraction concentrations of 0.45, 0.87, and 1.54 ppM respectively. The threshold for taint was clearly inferred to be less than 0.45 ppM of water soluble fraction. 18 refs., 2 figs

Laboratory modeling, field study, and numerical simulation of bioremediation of petroleum contaminants

International Nuclear Information System (INIS)

Livingston, R.J.; Islam, M.R.

1999-01-01

Historical methods of cleaning up petroleum hydrocarbons from the vadose zone, the capillary zone, and the aquifers are not technically true cleanup technologies but rather transfer techniques. In addition, environmental engineers are realizing that the standard remediation techniques are not entirely effective in removing the hazardous material in a reasonable time frame. Long-chain hydrocarbons such as kerosene, diesel, and waste oil are particularly difficult to remediate using conventional techniques. The use of bioremediation as an alternative remediation technology is fast becoming the technique of choice among many environmental professionals. This method offers substantial benefits not found in other remediation processes. Bioremediation is very cost effective, nondestructive, relatively uncomplicated in implementing, requires non specialized equipment, and can be extremely effective in removing recalcitrant petroleum hydrocarbons. This study researched the availability of viable microbial populations in the arid climate in South Dakota. Exponential growth of the bacteria and the ability of bacteria to degrade long-chain hydrocarbons indicated that healthy populations do exist and could be used to mineralize organic hydrocarbons. Experimental results indicated that bioremediation can be effectively enhanced in landfills as well as in the subsurface using a supply of harmless nutrients. The biodegradation rate can be further enhanced with the use of edible surfactant that helped disperse the petroleum products. Also, the use of hydrogen peroxide enhanced the oxygen availability and increased the degradation rate. Interestingly, the bacterial growth rate is found to be high in difficult-to-biodegrade contaminants, such as waste oil. A numerical simulation program was also developed that describes the bacterial growth in the subsurface along with the reduction in substrate (contamination). Results from this program were found to be consistent with laboratory

Petroleum hydrocarbon assessment in the sediments of the northeastern Havana littoral, Cuba

Energy Technology Data Exchange (ETDEWEB)

Companioni Dams, Eloy Yordad; Nunez Clemente, Ana Catalina; Cora Medina, Miriam Odette [Laboratorio de Quimica Ambiental, Centro de Investigaciones del Petroleo, Habana (Cuba)]. E-mail: elocompa@yahoo.com; Gonzalez Brovo, Luis [Centro de Aplicaciones Tecnologicas y Desarrollo Nuclear, Habana, (Cuba); Marbot Ramada, Rolando [Laboratorio de Quimica Analitica, Centro de Investigaciones del Petroleo, Habana (Cuba); Montes de Oca Porto, Rodny [Laboratorio Antidoping, Habana (Cuba); Rosabal Rodriguez, Maikel [Centro de Ingenieria y Manejo Ambiental de Bahias y Costas, Habana (Cuba); Diaz Diaz, Miguel angel [Laboratorio de Quimica Ambiental, Centro de Investigaciones del Petroleo, Habana (Cuba)

2009-02-15

As a part of a geochemical study, aliphatic and aromatic hydrocarbons were determined in surficial sediments, from a Cuban coastal zone located in the Northeastern Havana Littoral. Sediment samples were collected at 15 sites in this area, and then extracted and analyzed by gas chromatography with flame ionization and mass spectrometry detectors. Total concentration of both, aliphatic (AH) and aromatic (ArH) hydrocarbons, varied from 2.4 {+-} 0.2 to 105.1 {+-} 5.9 {mu}g/g (dry weight) and from 1.1 {+-} 0.2 to 38.4 {+-} 7.6 {mu}g/g (dry weight), respectively. The chromatography profile of AH was dominated by an unresolved complex mixture (UCM), and the presence of isoprenoid hydrocarbons, steranes and hopanes, indicated petroleum - related hydrocarbon inputs. The predominant concentration of phytoplanktonic molecular markers (pristane and nC17) in collected sediments, revealed the marine productivity in this sites. The anthropogenic contribution detected showed the impact of the petroleum exploration along this coastal area. [Spanish] Como parte de un estudio geoquimico se determinaron hidrocarburos alifaticos y aromaticos en sedimentos superficiales, de una zona costera situada en el Litoral Nordeste de La Habana. Las muestras de sedimento se colectaron en 15 estaciones de muestreo en esta area, y posteriormente se extrajeron y analizaron mediante cromatografia gaseosa con detectores de ionizacion a la llama y espectrometria de masas. Las concentraciones totales de hidrocarburos alifaticos (HA) e hidrocarburos aromaticos (HAr) variaron desde 2.4 {+-} 0.2 a 105.1 {+-} 5.9 {mu}g/g (peso eco) y desde 1.1 {+-} 0.2 a 38.4 {+-} 7.6 {mu}g/g (peso eco), respectivamente. El perfil cromatografico de los hidrocarburos alifaticos estuvo dominado por una mezcla compleja no resuelta (MCNR), y la presencia de hidrocarburos isoprenoides, esteranos y hopanos, indico el aporte de hidrocarburos derivados del petroleo. La concentracion predominante de marcadores moleculares

Toxicities of azadirachtin and polychlorinated petroleum Hydrocarbon against resist and susceptible strains of tribolium castaneum (coleoptera: tenebrionidae) adults

International Nuclear Information System (INIS)

Hussain, R.; Riaz, M.; Riaz, M.

2014-01-01

The LC/sub 50/ values for malathion-resistant (PAK) and organo-50 phosphate-susceptible (FSS-II) strains of red flour beetle, Tribolium castaneum (Herbst) (Coleoptera: Tenebrionidae) adult beetles were determined through filter paper impregnated method against azadirachtin (Nimbokil 60 EC) and polychlorinated petroleum hydrocarbon (Tenekil 100 EC). The LC values of these insecticides were worked out as 12830 and 50 9331 ppm for azadirachtin and 5148 and 4047 ppm for Tenekil 100 EC against PAK and FSS-II strains, respectively. The results revealed that polychlorinated petroleum hydrocarbon was more toxic than the azadirachtin. Furthermore, both the insecticides were equally toxic to the adult beetles of T. castaneum as the difference was non-significant because of overlapping 95% FLs to LC./sub 50/. (author)

Application of the Salmonella mutagenicity assay and determination of polycyclic aromatic hydrocarbons in workplaces exposed to petroleum pitch and petroleum coke

Energy Technology Data Exchange (ETDEWEB)

Monarca, S; Pasquini, R; Sforzolini, G S; Viola, V; Fagioli, F

1982-02-01

Workplaces of an Italian carbon electrode factory, exposed to petroleum pitch and petroleum coke, were studied using a coupled chemical and biological approach to evaluate occupational mutagenic/carcinogenic hazards. Analytical procedures for the determination of polycyclic aromatic hydrocarbons (PAH) and Salmonella/microsome mutagenicity tests were performed on both industrial ingredients and airborne particulate matter of the working environment, after fractionating by sequential Soxhlet extractions with four organic solvents of increasing polarity. The results showed: the presence of extraordinarily high PAH contents in the benzene extracts of petroleum pitch and of airborne particulate samples, in correlation with very high indirect (after metabolic activation) mutagenic responses of benzene extracts with strain TA98; very high indirect mutagenic responses in the other extracts of the airborne particulate samples; the production during the processing at high temperatures of directly acting mutaggens which were absent in the starting materials and their release in the air of workplaces. The comparison of chemical analytical and mutagenicity data has proved to be an interesting approach for better defining the relative health hazards due to occupational exposure to potentially mutagenic/carcinogenic petroleum products.

[Influence of Mirabilis jalapa Linn. Growth on the Microbial Community and Petroleum Hydrocarbon Degradation in Petroleum Contaminated Saline-alkali Soil].

Science.gov (United States)

Jiao, Hai-hua; Cui, Bing-jian; Wu, Shang-hua; Bai, Zhi-hui; Huang, Zhan-bin

2015-09-01

In order to explore the effect of Mirabilis jalapa Linn. growth on the structure characteristics of the microbial community and the degradation of petroleum hydrocarbon (TPH) in the petroleum-contaminated saline-alkali soil, Microbial biomass and species in the rhizosphere soils of Mirabilis jalapa Linn. in the contaminated saline soil were studied with the technology of phospholipid fatty acids (PLFAs) analysis. The results showed that comparing to CK soils without Mirabilis jalapa Linn., the ratio of PLFAs species varied were 71. 4%, 69. 2% and 33. 3% in the spring, summer and autumn season, respectively. In addition, there was distinct difference of the biomasses of the microbial community between the CK and rhizosphere soils and among the difference seasons of growth of Mirabilis jalapa Linn.. Compare to CK soil, the degradation rates of total petroleum hydrocarbon (TPH) was increased by 47. 6%, 28. 3%, and 18. 9% in spring, summer, and autumn rhizosphere soils, respectively. Correlation analysis was used to determine the correlation between TPH degradation and the soil microbial community. 77. 8% of the total soil microbial PLFAs species showed positive correlation to the TPH degradation (the correlation coefficient r > 0), among which, 55. 6% of PLFAs species showed high positive correlation(the correlation coefficient was r≥0. 8). In addition, the relative content of SAT and MONO had high correlation with TPH degradation in the CK sample soils, the corelation coefficient were 0. 92 and 0. 60 respectively; However, the percent of positive correlation was 42. 1% in the rhizosphere soils with 21. 1% of them had high positive correlation. The relative content of TBSAT, MONO and CYCLO had moderate or low correlation in rhizosphere soils, and the correlation coefficient were 0. 56, 0. 50, and 0. 07 respectively. Our study showed that the growth of mirabilis Mirabilis jalapa Linn. had a higher influence on the species and biomass of microbial community in the

Bio-electrochemical system (BES) as an innovative approach for sustainable waste management in petroleum industry.

Science.gov (United States)

Srikanth, Sandipam; Kumar, Manoj; Puri, S K

2018-02-15

Petroleum industry is one of the largest and fast growing industries due to the ever increasing global energy demands. Petroleum refinery produces huge quantities of wastes like oily sludge, wastewater, volatile organic compounds, waste catalyst, heavy metals, etc., because of its high capacity and continuous operation of many units. Major challenge to this industry is to manage the huge quantities of waste generated from different processes due to the complexity of waste as well as changing stringent environmental regulations. To decrease the energy loss for treatment and also to conserve the energy stored in the chemical bonds of these waste organics, bio-electrochemical system (BES) may be an efficient tool that reduce the economics of waste disposal by transforming the waste into energy pool. The present review discusses about the feasibility of using BES as a potential option for harnessing energy from different waste generated from petroleum refineries. Copyright © 2018. Published by Elsevier Ltd.

A soil washing pilot plant for removing petroleum hydrocarbons from contaminated soils

International Nuclear Information System (INIS)

Toor, I.A.; Roehrig, G.R.

1992-01-01

A soil washing pilot plant was built and tested for its ability to remove petroleum hydrocarbons from certain soils. The ITEX soil washing pilot plant is a trailer mountable mobile unit which has a washing capacity of two tons per hour of contaminated soils. A benchscale study was carried out prior to the fabrication of the pilot plant. The first sample was contaminated with diesel fuel while the second sample was contaminated with crude oil. Various nonionic, cationic and anionic cleaning agents were evaluated for their ability to remove petroleum hydrocarbons from these materials. The nonionic cleaning agents were more successful in cleaning the soils in general. The ultimate surfactant choice was based on several factors including cost, biodegradability, cleaning efficiency and other technical considerations. The soil samples were characterized in terms of their particle size distributions. Commercial diesel fuel was carefully mixed in this sand to prepare a representative sample for the pilot plant study. Two pilot runs were made using this material. A multistage washing study was also conducted in the laboratory which indicates that the contamination level can be reduced to 100 ppm using only four stages. Because the pilot plant washing efficiency is twice as high, it is believed that ultimate contamination levels can be reduced to lower levels using the same number of stages. However, this hypothesis has not been demonstrated to date

Total petroleum hydrocarbon degradation by hybrid electrobiochemical reactor in oilfield produced water

International Nuclear Information System (INIS)

Mousa, Ibrahim E.

2016-01-01

The crude oil drilling and extraction operations are aimed to maximize the production may be counterbalanced by the huge production of contaminated produced water (PW). PW is conventionally treated through different physical, chemical, and biological technologies. The efficiency of suggested hybrid electrobiochemical (EBC) methods for the simultaneous removal of total petroleum hydrocarbon (TPH) and sulfate from PW generated by petroleum industry is studied. Also, the factors that affect the stability of PW quality are investigated. The results indicated that the effect of biological treatment is very important to keep control of the electrochemical by-products and more TPH removal in the EBC system. The maximum TPH and sulfate removal efficiency was achieved 75% and 25.3%, respectively when the detention time was about 5.1 min and the energy consumption was 32.6 mA/cm 2 . However, a slight increasing in total bacterial count was observed when the EBC compact unit worked at a flow rate of average 20 L/h. Pseudo steady state was achieved after 30 min of current application in the solution. Also, the results of the study indicate that when the current intensity was increased above optimum level, no significant results occurred due to the release of gases. - Highlights: • The hybrid electrolytic biological cell was used for degradation of oilfield produced water. • Decomposition of Total Petroleum Hydrocarbon with or without the biofilter. • High saline water with the high chloride and sulfate ions content treatment. • The removal of electrochemical by-products is a phase change technique that requires the maintenance the biofilm on the filter media, which is sensitive and a complex operation. • Biofilter is efficient for the degradation of PW bye products, the critical drawback to their utility in full-scale operations is high TDS water content and detention time of treatment.

Degradation of volatile hydrocarbons from steam-classified solid waste by a mixture of aromatic hydrocarbon-degrading bacteria.

Science.gov (United States)

Leahy, Joseph G; Tracy, Karen D; Eley, Michael H

2003-03-01

Steam classification is a process for treatment of solid waste that allows recovery of volatile organic compounds from the waste via steam condensate and off-gases. A mixed culture of aromatic hydrocarbon-degrading bacteria was used to degrade the contaminants in the condensate, which contained approx. 60 hydrocarbons, of which 38 were degraded within 4 d. Many of the hydrocarbons, including styrene, 1,2,4-trimethylbenzene, naphthalene, ethylbenzene, m-/p-xylene, chloroform, 1,3-dichloropropene, were completely or nearly completely degraded within one day, while trichloroethylene and 1,2,3-trichloropropane were degraded more slowly.

Total Petroleum Hydrocarbon Criteria Working Group (TPHCWG) Field Demonstration Report: IRP Site 4, POL Area, Springfield ANG Base, Springfield, Ohio

National Research Council Canada - National Science Library

Reed, Dennis

2003-01-01

...) methodology to compare the approaches. Soil core composites were analyzed for trichloroethylene, gasoline-range organics, volatile petroleum hydrocarbons, benzene, toluene, ethylbenzene, and xylenes...

Natural and anthropogenic hydrocarbon inputs to sediments of Patos Lagoon Estuary, Brazil.

Science.gov (United States)

Medeiros, Patricia Matheus; Bícego, Márcia Caruso; Castelao, Renato Menezes; Del Rosso, Clarissa; Fillmann, Gilberto; Zamboni, Ademilson Josemar

2005-01-01

The Patos Lagoon Estuary, southern Brazil, is an area of environmental interest not only because of tourism, but also because of the presence of the second major port of Brazil, with the related industrial and shipping activities. Thus, potential hydrocarbon pollution was examined in this study. Sediment samples were collected at 10 sites in the estuary, extracted, and analyzed by GC-FID and GC-MS for composition and concentration of the following organic geochemical markers: normal and isoprenoid alkanes, petroleum biomarkers, linear alkylbenzenes (LABs), and polycyclic aromatic hydrocarbons (PAHs). The total concentrations varied from 1.1 to 129.6 microg g(-1) for aliphatic hydrocarbons, from 17.8 to 4510.6 ng g(-1) for petroleum biomarkers, from 3.2 to 1601.9 ng g(-1) for LABs, and from 37.7 to 11,779.9 ng g(-1) for PAHs. Natural hydrocarbons were mainly derived from planktonic inputs due to a usual development of blooms in the estuary. Terrestrial plant wax compounds prevailed at sites located far from Rio Grande City and subject to stronger currents. Anthropogenic hydrocarbons are related to combustion/pyrolysis processes of fossil fuel, release of unburned oil products and domestic/industrial waste outfalls. Anthropogenic hydrocarbon inputs were more apparent at sites associated with industrial discharges (petroleum distributor and refinery), shipping activities (dry docking), and sewage outfalls (sewage). The overall concentrations of anthropogenic hydrocarbons revealed moderate to high hydrocarbon pollution in the study area.

Bioavailability and bioaccessibility of petroleum hydrocarbons in contaminated site soils

International Nuclear Information System (INIS)

Stephenson, G.; Angell, R.; Strive, E.; Ma, W.

2010-01-01

Although the bioavailability and/or bioaccessibility of contaminants in soil can be measured by various ecological receptors, the methods that are suitable for metals do not necessarily work well for petroleum hydrocarbons (PHCs). In this study, several biological and chemical methods were used at various PHC contaminated sites to find the most fitting method for different soil types in terms of predicting the biological responses of organisms as measured by standard single species toxicity tests. Organisms such as plants, earthworms, and collembolan were exposed to soils with different PHC concentrations. Multiple endpoints were then measured to evaluate the biological responses. The exposure concentrations for the 4 CCME hydrocarbon fractions were measured using hexane:acetone extraction as well as extractions with cyclodextrin, and a mixture of enzymes to simulate the gastro-intestinal fluid of an earthworm. The estimated exposure concentrations depended on the extraction method. The study showed that existing methodologies must be modified in order to better estimate the biological effect of PHCs in soil. Comparative data was presented and discussed along with proposed methodological modifications.

Bioavailability and bioaccessibility of petroleum hydrocarbons in contaminated site soils

Energy Technology Data Exchange (ETDEWEB)

Stephenson, G.; Angell, R.; Strive, E.; Ma, W. [Stantec Consulting Ltd., Surrey, BC (Canada)

2010-07-01

Although the bioavailability and/or bioaccessibility of contaminants in soil can be measured by various ecological receptors, the methods that are suitable for metals do not necessarily work well for petroleum hydrocarbons (PHCs). In this study, several biological and chemical methods were used at various PHC contaminated sites to find the most fitting method for different soil types in terms of predicting the biological responses of organisms as measured by standard single species toxicity tests. Organisms such as plants, earthworms, and collembolan were exposed to soils with different PHC concentrations. Multiple endpoints were then measured to evaluate the biological responses. The exposure concentrations for the 4 CCME hydrocarbon fractions were measured using hexane:acetone extraction as well as extractions with cyclodextrin, and a mixture of enzymes to simulate the gastro-intestinal fluid of an earthworm. The estimated exposure concentrations depended on the extraction method. The study showed that existing methodologies must be modified in order to better estimate the biological effect of PHCs in soil. Comparative data was presented and discussed along with proposed methodological modifications.

Removal of light petroleum hydrocarbons from water sources using polypropylene and titanium dioxide nano-composite

Directory of Open Access Journals (Sweden)

H. Karyab

2016-08-01

Full Text Available Background: Petroleum hydrocarbons are the most important pollutants which threat human health and aquatics. Adsorbents are one of the common equipment in water pollution management; however, their applications have been associated with limitations. Objective: To evaluate the potential of polypropylene/titanium dioxide Nano-composite in adsorption of light petroleum hydrocarbons from water sources. Methods: This experimental study was conducted at school of health, Qazvin University of Medical Sciences in 2014-15. Activation of polypropylene fibers, with 1 cm length and 300 microns diameters, was achieved with wet heating. To synthesize of nano-composite the fibers were coated with nano-titanium dioxide with 20 nm diameter. The sonication was performed at 26 kHz and 100 W of power in 40ºc. The morphology of the fractured surfaces of impact specimens was examined by FESEM. The adsorption rate of petrol and gasoline, as surrogate of TPH, was evaluated in different retention time within polyamide mesh aperture diameter of 250 nm. Average of TPH adsorbing, per unit weight of adsorbent, were analyzed with analysis of variance and Scheffe post hoc tests. Findings: The FESEM micrographs showed that the dispersion of the nano-Tio2 particles was relatively good and only few aggregations exist. The maximum adsorption capacity of petrol and gasoline was obtained in 30 minute. The adsorption rate of gasoline was 6.49±0.10 g/g and oil was 7.01±0.13 g/g. Conclusion: According to the results and in comparison with commercial imported adsorbents, the synthesized Nano-composite had favorable performance. The results show that the polypropylene/Tio2 Nano-composite can be used effectively in light petroleum hydrocarbons removal from polluted water sources.

Application of electrochemical technology for removing petroleum hydrocarbons from produced water using lead dioxide and boron-doped diamond electrodes.

Science.gov (United States)

Gargouri, Boutheina; Gargouri, Olfa Dridi; Gargouri, Bochra; Trabelsi, Souhel Kallel; Abdelhedi, Ridha; Bouaziz, Mohamed

2014-12-01

Although diverse methods exist for treating polluted water, the most promising and innovating technology is the electrochemical remediation process. This paper presents the anodic oxidation of real produced water (PW), generated by the petroleum exploration of the Petrobras plant-Tunisia. Experiments were conducted at different current densities (30, 50 and 100 mA cm(-2)) using the lead dioxide supported on tantalum (Ta/PbO2) and boron-doped diamond (BDD) anodes in an electrolytic batch cell. The electrolytic process was monitored by the chemical oxygen demand (COD) and the residual total petroleum hydrocarbon [TPH] in order to know the feasibility of electrochemical treatment. The characterization and quantification of petroleum wastewater components were performed by gas chromatography mass spectrometry. The COD removal was approximately 85% and 96% using PbO2 and BDD reached after 11 and 7h, respectively. Compared with PbO2, the BDD anode showed a better performance to remove petroleum hydrocarbons compounds from produced water. It provided a higher oxidation rate and it consumed lower energy. However, the energy consumption and process time make useless anodic oxidation for the complete elimination of pollutants from PW. Cytotoxicity has shown that electrochemical oxidation using BDD could be efficiently used to reduce more than 90% of hydrocarbons compounds. All results suggest that electrochemical oxidation could be an effective approach to treat highly concentrated organic pollutants present in the industrial petrochemical wastewater and significantly reduce the cost and time of treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

Petroleum-related contaminants near a produced water discharge site in the Santa Barbara Channel

International Nuclear Information System (INIS)

Jones, A.D.; Witter, A.E.; Higashi, R.M.

1994-01-01

Offshore oil production generates substantial quantities of waste water that is frequently discharged into marine waters. Contamination of coastal sediments occurs due to other inputs including natural petroleum seeps, and this complicates assessments of the environmental effects of produced water in marine ecosystems. The current study has focused on characterization of contaminants in sediments near produced water discharge site off the coast of Southern California. First, it was important to address the question: ''What contaminants in sediments should be monitored as indicators of produced water effects?'' Dichloromethane extracts of sediments were analyzed for numerous organic constituents using gas chromatography-mass spectrometry and selected ion monitoring. Though the phenols and fatty acids were not detected in sediment extracts, normal and branched alkanes and other petroleum hydrocarbon biomarkers were quantified. No relationship was evident that related absolute concentrations of organic compounds to distance from the outfall, but patterns of petroleum hydrocarbons exhibited consistent spatial variations that could be related to distance from the produced water out fall. Analysis of chemical fossil ''biomarkers'' provides potentially useful indices of effects of waste discharges upon microbial biodegradation of organic compounds in sediments

Changes in hydrocarbon groups, soil ecotoxicity and microbiology along horizontal and vertical contamination gradients in an old landfarming field for oil refinery waste.

Science.gov (United States)

Mikkonen, Anu; Hakala, Kati P; Lappi, Kaisa; Kondo, Elina; Vaalama, Anu; Suominen, Leena

2012-03-01

Horizontal and vertical contaminant gradients in an old landfarming field for oil refinery waste were characterised with the aim to assess parallel changes in hydrocarbon groups and general, microbiological and ecotoxicological soil characteristics. In the surface soil polar compounds were the most prevalent fraction of heptane-extractable hydrocarbons, superseding GC-FID-resolvable and high-molar-mass aliphatics and aromatics, but there was no indication of their relatively higher mobility or toxicity. The size of the polar fraction correlated poorly with soil physical, chemical and microbiological properties, which were better explained by the total heptane-extractable and total petroleum hydrocarbons (TPH). Deleterious effects on soil microbiology in situ were observed at surprisingly low TPH concentrations (0.3%). Due to the accumulation of polar and complexed degradation products, TPH seems an insufficient measure to assess the quality and monitor the remediation of soil with weathered hydrocarbon contamination. Copyright © 2011 Elsevier Ltd. All rights reserved.

Fate and transport of petroleum hydrocarbons in soil and ground water at Big South Fork National River and Recreation Area, Tennessee and Kentucky, 2002-2003

Science.gov (United States)

Williams, Shannon D.; Ladd, David E.; Farmer, James

2006-01-01

In 2002 and 2003, the U.S. Geological Survey (USGS), by agreement with the National Park Service (NPS), investigated the effects of oil and gas production operations on ground-water quality at Big South Fork National River and Recreation Area (BISO) with particular emphasis on the fate and transport of petroleum hydrocarbons in soils and ground water. During a reconnaissance of ground-water-quality conditions, samples were collected from 24 different locations (17 springs, 5 water-supply wells, 1 small stream, and 1 spring-fed pond) in and near BISO. Benzene, toluene, ethylbenzene, and xylene (BTEX) compounds were not detected in any of the water samples, indicating that no widespread contamination of ground-water resources by dissolved petroleum hydrocarbons probably exists at BISO. Additional water-quality samples were collected from three springs and two wells for more detailed analyses to obtain additional information on ambient water-quality conditions at BISO. Soil gas, soil, water, and crude oil samples were collected at three study sites in or near BISO where crude oil had been spilled or released (before 1993). Diesel range organics (DRO) were detected in soil samples from all three of the sites at concentrations greater than 2,000 milligrams per kilogram. Low concentrations (less than 10 micrograms per kilogram) of BTEX compounds were detected in lab-analyzed soil samples from two of the sites. Hydrocarbon-degrading bacteria counts in soil samples from the most contaminated areas of the sites were not greater than counts for soil samples from uncontaminated (background) sites. The elevated DRO concentrations, the presence of BTEX compounds, and the low number of -hydrocarbon-degrading bacteria in contaminated soils indicate that biodegradation of petroleum hydrocarbons in soils at these sites is incomplete. Water samples collected from the three study sites were analyzed for BTEX and DRO. Ground-water samples were collected from three small springs at the

Variability of soil potential for biodegradation of petroleum hydrocarbons in a heterogeneous subsurface

DEFF Research Database (Denmark)

Kristensen, Andreas Houlberg; Poulsen, Tjalfe; Mortensen, Lars

2010-01-01

for biodegradation was highly variable, which from autoregressive state-space modeling was partly explained by changes in soil air-filled porosity and gravimetric water content. The results suggest considering biological heterogeneity when evaluating the fate of contaminants in the subsurface.......Quantifying the spatial variability of factors affecting natural attenuation of hydrocarbons in the unsaturated zone is important to (i) performing a reliable risk assessment and (ii) evaluating the possibility for bioremediation of petroleum-polluted sites. Most studies to date have focused...... on the shallow unsaturated zone. Based on a data set comprising analysis of about 100 soil samples taken in a 16-m-deep unsaturated zone polluted with volatile petroleum compounds, we statistically and geostatistically analyzed values of essential soil properties. The subsurface of the site was highly layered...

Biodegradation of different petroleum hydrocarbons by free and immobilized microbial consortia.

Science.gov (United States)

Shen, Tiantian; Pi, Yongrui; Bao, Mutai; Xu, Nana; Li, Yiming; Lu, Jinren

2015-12-01

The efficiencies of free and immobilized microbial consortia in the degradation of different types of petroleum hydrocarbons were investigated. In this study, the biodegradation rates of naphthalene, phenanthrene, pyrene and crude oil reached about 80%, 30%, 56% and 48% under the optimum environmental conditions of free microbial consortia after 7 d. We evaluated five unique co-metabolic substances with petroleum hydrocarbons, α-lactose was the best co-metabolic substance among glucose, α-lactose, soluble starch, yeast powder and urea. The orthogonal biodegradation analysis results showed that semi-coke was the best immobilized carrier followed by walnut shell and activated carbon. Meanwhile, the significance of various factors that contribute to the biodegradation of semi-coke immobilized microbial consortia followed the order of: α-lactose > semi-coke > sodium alginate > CaCl2. Moreover, the degradation rate of the immobilized microbial consortium (47%) was higher than that of a free microbial consortium (26%) under environmental conditions such as the crude oil concentration of 3 g L(-1), NaCl concentration of 20 g L(-1), pH at 7.2-7.4 and temperature of 25 °C after 5 d. SEM and FTIR analyses revealed that the structure of semi-coke became more porous and easily adhered to the microbial consortium; the functional groups (e.g., hydroxy and phosphate) were identified in the microbial consortium and were changed by immobilization. This study demonstrated that the ability of microbial adaptation to the environment can be improved by immobilization which expands the application fields of microbial remediation.

Factors controlling leaching of polycyclic aromatic hydrocarbons from petroleum source rock using nonionic surfactant

Energy Technology Data Exchange (ETDEWEB)

Akinlua, Akinsehinwa [Obafemi Awolowo Univ., Ile-Ife (Nigeria). Fossil Fuels and Environmental Geochemistry Group; Jochmann, Maik A.; Qian, Yuan; Schmidt, Torsten C. [Duisburg-Essen Univ., Essen (Germany). Instrumental Analytical Chemistry; Sulkowski, Martin [Duisburg-Essen Univ., Essen (Germany). Inst. of Environmental Analytical Chemistry

2012-03-15

The extraction of polycyclic aromatic hydrocarbons (PAHs) from petroleum source rock by nonionic surfactants with the assistance of microwave irradiation was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and type of surfactant have significant effects on extraction yields of PAHs. Factors such as surfactant concentration, irradiation power, sample/solvent ratio and mixing surfactants (i.e., mixture of surfactant at specific ratio) also influence the extraction efficiencies for these compounds. The optimum temperature for microwave-assisted nonionic surfactant extraction of PAHs from petroleum source rock was 120 C and the best suited surfactant was Brij 35. The new method showed extraction efficiencies comparable to those afforded by the Soxhlet extraction method, but a reduction of the extraction times and environmentally friendliness of the new nonionic surfactant extraction system are clear advantages. The results also show that microwave-assisted nonionic surfactant extraction is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock. (orig.)

Effects of diurnal temperature variation on microbial community and petroleum hydrocarbon biodegradation in contaminated soils from a sub-Arctic site.

Science.gov (United States)

Akbari, Ali; Ghoshal, Subhasis

2015-12-01

Contaminated soils are subject to diurnal and seasonal temperature variations during on-site ex-situ bioremediation processes. We assessed how diurnal temperature variations similar to that in summer at the site from which petroleum hydrocarbon-contaminated soil was collected affect the soil microbial community and the extent of biodegradation of petroleum hydrocarbons compared with constant temperature regimes. Microbial community analyses for 16S rRNA and alkB genes by pyrosequencing indicated that the microbial community for soils incubated under diurnal temperature variation from 5°C to 15°C (VART5-15) evolved similarly to that for soils incubated at constant temperature of 15°C (CST15). In contrast, under a constant temperature of 5°C (CST5), the community evolved significantly different. The extent of biodegradation of C10-C16 hydrocarbons in the VART5-15 systems was 48%, comparable with the 41% biodegradation in CST15 systems, but significantly higher than CST5 systems at 11%. The enrichment of Gammaproteobacteria was observed in the alkB gene-harbouring communities in VART5-15 and CST15 but not in CST5 systems. However, the Actinobacteria was abundant at all temperature regimes. The results suggest that changes in microbial community composition as a result of diurnal temperature variations can significantly influence petroleum hydrocarbon bioremediation performance in cold regions. © 2015 Society for Applied Microbiology and John Wiley & Sons Ltd.

Methanogenic degradation of petroleum hydrocarbons in subsurface environments remediation, heavy oil formation, and energy recovery.

Science.gov (United States)

Gray, N D; Sherry, A; Hubert, C; Dolfing, J; Head, I M

2010-01-01

Hydrocarbons are common constituents of surface, shallow, and deep-subsurface environments. Under anaerobic conditions, hydrocarbons can be degraded to methane by methanogenic microbial consortia. This degradation process is widespread in the geosphere. In comparison with other anaerobic processes, methanogenic hydrocarbon degradation is more sustainable over geological time scales because replenishment of an exogenous electron acceptor is not required. As a consequence, this process has been responsible for the formation of the world's vast deposits of heavy oil, which far exceed conventional oil assets such as those found in the Middle East. Methanogenic degradation is also a potentially important component of attenuation in hydrocarbon contamination plumes. Studies of the organisms, syntrophic partnerships, mechanisms, and geochemical signatures associated with methanogenic hydrocarbon degradation have identified common themes and diagnostic markers for this process in the subsurface. These studies have also identified the potential to engineer methanogenic processes to enhance the recovery of energy assets as biogenic methane from residual oils stranded in petroleum systems. Copyright 2010 Elsevier Inc. All rights reserved.

Application of the salmonella mutagenicity assay and determination of polycyclic aromatic hydrocarbons in workplaces exposed to petroleum pitch and petroleum coke

Energy Technology Data Exchange (ETDEWEB)

Monarca, S; Pasquini, R; Sforzolini, G S; Fagioli, F; Viola, V

1982-02-01

Workplaces of an Italian carbon electrode factory, exposed to petroleum pitch and petroleum coke, were studied using a coupled chemical and biological approach to evaluate occupational mutagenic/carcinogenic hazards. Analytical procedures for the determination of polycyclic aromatic hydrocarbons (PAH) and Salmonella/microsome mutagenicity tests were performed on pitch and coke and airborne particulate matter of the working environment, after fractionating by sequential Soxhlet extractions with four organic solvents of increasing polarity (benzene, chloroform, methanol and acetone). The results showed: (a) the presence of extraordinarily high PAH (carcinogenic and noncarcinogenic) contents in the benzene extracts of petroleum pitch (3.6 wt% of total PAH) and of airborne particulate samples (up to 0.35 wt% of total PAH), in correlation with very high indirect mutagenic responses of benzene extracts; (b) very high indirect mutagenic responses in the other extracts of the airborne particulate samples; (c) the production during the processing at high temperatures of directly acting mutagens which were absent in the starting materials and their release in the air of workplaces. The comparison of chemical analytical and mutagenicity data has proved to be an interesting approach for better defining the relative health hazards due to occupational exposure to potentially mutagenic/carcinogenic petroleum products.

2005 yearly days of petroleum

International Nuclear Information System (INIS)

Constant, R.; Susbielles, G.

2005-01-01

14 articles are gathered in this data sheet; they deal with the opening address of the 2005 petroleum days; the hydrocarbons: the evolutive resource; the para-petroleum engineers and the Europe; the speech of Mr Francois Loos; the Shell global scenarios to 2025; the evolution of the gas resource and its uses; the French para-petroleum industry; Bernard Bensaid, Corinne Sagary, Armelle Saniere, economic studies, IFP; the contribution of the innovation and of the technology in the diversification of the hydrocarbons supply; innovation and diversification of the petroleum resource: the point of view of Total; research, development and diversification of the petroleum resource; innovation in services companies; innovation in study and development and engineering; the closing address of the 2005 petroleum days. (O.M.)

Embryotoxic and teratogenic effects of petroleum hydrocarbons in mallards (Anas platyrhynchos)

Science.gov (United States)

Hoffman, D.J.

1979-01-01

Egg surface applications of microliter quantities of crude and refined oils of high aromatic content are embryotoxic to mallards (Anas platyrhynchos) and other avian species; applications of aliphatic hydrocarbons have virtually no effect. Mallard eggs at 72 h of development were exposed to a mixture of aromatic hydrocarbons or to aromatic compounds representative to those present in crude oil to assess their toxicity. The class composition of the mixture was similar to that of South Louisiana crude oil, an American Petroleum Institute reference oil. Application of 20 microliter of the mixture reduced embryonic survival by nearly 70%. The temporal pattern of embryonic death was similar to that after exposure to South Louisiana crude oil. Embryonic growth was stunted, as reflected by weight, crown-rump length, and bill length, and there was a significant increase in the incidence of abnormal survivors. When individual classes of aromatic hydrocarbons were tested, tetracyclics caused some embryonic death at the concentrations in the mixture. When classes were tested in all possible combinations of two, no combination appeared to be as toxic as the entire mixture. Addition of the tetracyclic compound chrysene to the aromatic mixture considerably enhanced embryotoxicity, but could not completely account for the toxicity of the crude oil. The presence of additional unidentified polycyclic aromatic hydrocarbons as well as methylated derivatives of polycyclic aromatic compounds such as chrysene may further account for the embryotoxicity of the crude oil.

Innovative hazardous waste treatment technology

International Nuclear Information System (INIS)

Freeman, H.M.; Sferra, P.R.

1990-01-01

This book contains 21 various biodegradation techniques for hazardous waste treatment. Topics include: cyclic vertical water table movement for enhancement of in situ biodegradation of diesel fuel; enhanced biodegradation of petroleum hydrocarbons; and evaluation of aeration methods to bioremediate fuel-contaminated soils

Evaluating the impact of extraction and cleanup parameters on the yield of total petroleum hydrocarbons in soil

Energy Technology Data Exchange (ETDEWEB)

Saari, Eija; Peraemaeki, Paavo; Jalonen, Jorma [University of Oulu, Department of Chemistry (Finland)

2008-11-15

Interlaboratory comparisons for the analysis of mineral oil in polluted soil using the GC-FID method indicate that extraction and cleanup conditions have significant effects on the analytical results. In this investigation a ruggedness test was performed on the extraction and cleanup method for the determination of total petroleum hydrocarbons in soil. A two-level Plackett-Burman design was utilized to study the effect of 11 different method parameters on the extraction recovery of total petroleum hydrocarbons (TPH) in soil. Both qualitative and quantitative factors were investigated. The results indicate that total petroleum hydrocarbons can be relatively reliably monitored through strict implementation of the ISO and CEN draft standards. However, variation in certain method parameters readily affects the validity of the results. The most critical factors affecting TPH recovery were the solvent and co-solvent used for extraction, the extraction time, adsorbent and its weight and sample TPH concentration. Because adaptation of the draft standards especially with respect to these factors easily leads to TPH recoveries higher than 200% or lower than 70%, the validity of the adapted method should always be verified. A proper estimate of the expanded uncertainty should also be appended to TPH results, because only then can the reliability of the results be guaranteed and further justification is gained to support the end-use of the data. This also supports the credibility of the analytical services and prevents the data end-users from drawing misleading conclusions concerning the environmental risks and potential remediation requirements. (orig.)

Thermal soil desorption for total petroleum hydrocarbon testing on gas chromatographs

International Nuclear Information System (INIS)

Mott, J.

1995-01-01

Testing for total petroleum hydrocarbons (TPH) is one of the most common analytical tests today. A recent development in chromatography incorporates Thermal Soil Desorption technology to enable analyses of unprepared soil samples for volatiles such as BTEX components and semi-volatiles such as diesel, PCBs, PAHs and pesticides in the same chromatogram, while in the field. A gas chromatograph is the preferred method for determining TPH because the column in a GC separates the individual hydrocarbons compounds such as benzene and toluene from each other and measures each individually. A GC analysis will determine not only the total amount of hydrocarbon, but also whether it is gasoline, diesel or another compound. TPH analysis with a GC is typically conducted with a Flame Ionization Detector (FID). Extensive field and laboratory testing has shown that incorporation of a Thermal Soil Desorber offers many benefits over traditional analytical testing methods such as Headspace, Solvent Extraction, and Purge and Trap. This paper presents the process of implementing Thermal Soil Desorption in gas chromatography, including procedures for, and advantages of faster testing and analysis times, concurrent volatile and semi-volatile analysis, minimized sample manipulation, single gas (H 2 ) operation, and detection to the part-per billion levels

Contribution of offshore petroleum deposits to marine food chain

Science.gov (United States)

Mori, S.

2009-12-01

Petroleum production out of offshore petroleum deposits often coincides with abundant fisheries in the world. Superposition of marine microorganism concentration distribution and offshore petroleum field distribution from various data in the literature provides to prove this coincidence. Sakhalin Island coastal regions, North Sea, Gulf of Mexico, etc. are chosen for the superpositions. Significant conformity is observed between the plankton concentration distribution and the offshore petroleum deposit distribution in all those regions. Also, most studies on the consequence of oil spills to marine eco-systems have focused mainly on hazardous marine pollution caused by spilled petroleum at high concentration in marine environment. However, some of those data clearly indicate stimulation of plankton population in properly low concentration levels of dissolved hydrocarbons and dissolved petroleum compositions. Further, increase of hydrocarbon concentration leads to its inhibition from its stimulation conditions upon crossing over a critical concentration level—a plankton stimulation/inhibition threshold concentration (SITC) of hydrocarbons. The SITC varies depending on hydrocarbon compounds, petroleum compositions, and microorganisms such as planktons. Further, petroleum composition diffusing through subterranean layers from petroleum deposits reacts with dissolved oxygen to be consumed at the ocean floor to precipitate the agglomerate suspension of hydrocarbons, leaving the sea water in a condition of oxygen depletion on the ocean floor. Such incidents are also briefly discussed.Plankton stimulation/inhibition threshold concentration of petroleum fractions

Petroleum pollution in surface sediments of Daya Bay, South China, revealed by chemical fingerprinting of aliphatic and alicyclic hydrocarbons

Science.gov (United States)

Gao, Xuelu; Chen, Shaoyong

2008-10-01

Nine surface sediments collected from Daya Bay have been Soxhlet-extracted with 2:1 (v/v) dichloromethane-methanol. The non-aromatic hydrocarbon (NAH) fraction of solvent extractable organic matter (EOM) and some bulk geochemical parameters have been analyzed to determine petroleum pollution of the bay. The NAH content varies from 32 to 276 μg g -1 (average 104 μg g -1) dry sediment and accounts for 5.8-64.1% (average 41.6%) of the EOM. n-Alkanes with carbon number ranging from 15 to 35 are identified to be derived from both biogenic and petrogenic sources in varying proportions. The contribution of marine authigenic input to the sedimentary n-alkanes is lower than the allochthonous input based on the average n-C 31/ n-C 19 alkane ratio. 25.6-46.5% of the n-alkanes, with a mean of 35.6%, are contributed by vascular plant wax. Results of unresolved complex mixture, isoprenoid hydrocarbons, hopanes and steranes also suggest possible petroleum contamination. There is strong evidence of a common petroleum contamination source in the bay.

Engineered in situ bioremediation of a petroleum hydrocarbon-contaminated aquifer: assessment of mineralization based on alkalinity, inorganic carbon and stable carbon isotope balances

Science.gov (United States)

Hunkeler, Daniel; Höhener, Patrick; Bernasconi, Stefano; Zeyer, Josef

1999-04-01

A concept is proposed to assess in situ petroleum hydrocarbon mineralization by combining data on oxidant consumption, production of reduced species, CH 4, alkalinity and dissolved inorganic carbon (DIC) with measurements of stable isotope ratios. The concept was applied to a diesel fuel contaminated aquifer in Menziken, Switzerland, which was treated by engineered in situ bioremediation. In the contaminated aquifer, added oxidants (O 2 and NO 3-) were consumed, elevated concentrations of Fe(II), Mn(II), CH 4, alkalinity and DIC were detected and the DIC was generally depleted in 13C compared to the background. The DIC production was larger than expected based on the consumption of dissolved oxidants and the production of reduced species. Stable carbon isotope balances revealed that the DIC production in the aquifer originated mainly from microbial petroleum hydrocarbon mineralization, and that geochemical reactions such as carbonate dissolution produced little DIC. This suggests that petroleum hydrocarbon mineralization can be underestimated if it is determined based on concentrations of dissolved oxidants and reduced species.

A novel phytoremediation technology shown to remediate petroleum hydrocarbons from soils in situ

Energy Technology Data Exchange (ETDEWEB)

Huang, X.D.; Yu, X.M.; Gerhardt, K.; Glick, B.; Greenberg, B [Waterloo Environmental Biotechnology Inc., Hamilton, ON (Canada); Waterloo Univ., ON (Canada). Dept. of Biology

2009-04-01

This article described a newly developed, advanced microbe-enhanced phytoremediation system that can be used to remediate lands polluted by hydrocarbons, salts and metals. The technology uses 3 complementary processes to achieve effective remediation of strongly bound persistent organic pollutants (POPs) from soil. The remediation process involves physical soil treatment, photochemical photooxidation, microbial remediation and growth of plants treated with plant growth promoting rhizobacteria (PGPR). The PGPR-enhanced phytoremediation system (PEPS) alleviates plant stress and increases biodegradation activities, thereby accelerating plant growth in the presence of POPs or poor soils. The PEPS has been used successfully to remove petroleum hydrocarbons (PHCs) from impacted soils in situ at several sites across Canada. Studies have shown that the PHCs are degraded in the rhizosphere. This article also presented a summary of the work conducted at 3 sites in Alberta. It took only 2 years to remediate the 3 sites to levels required for site closure under Alberta Tier 1 guidelines. It was concluded that PEPS is equally effective for total PHC and Fraction 3 CCME hydrocarbons. 1 tab., 3 figs.

Effects of humic acid on phytodegradation of petroleum hydrocarbons in soil simultaneously contaminated with heavy metals

Institute of Scientific and Technical Information of China (English)

Soyoung Park; Ki Seob Kim; Jeong-Tae Kim; Daeseok Kang; Kijune Sung

2011-01-01

The use of humic acid (HA) to enhance the efficiency of phytodegradation of petroleum hydrocarbons in soil contaminated with diesel fuel was evaluated in this study.A sample of soil was artificially contaminated with commercially available diesel fuel to an initial total petroleum hydrocarbons (TPH) concentration of 2300 mg/kg and four heavy metals with concentrations of 400 mg/kg for Pb,200 mg/kg for Cu,12 mg/kg for Cd,and 160 mg/kg for Ni.Three plant species,Brassica campestris,Festuca arundinacea,and Helianthus annuus,were selected for the phytodegradation experiment.Percentage degradation of TPH in the soil in a control pot supplemented with HA increased to 45% from 30% without HA.The addition of HA resulted in an increases in the removal of TPH from the soil in pots planted with B.campestris,F.arundinacea,and H.annuus,enhancing percentage degradation to 86%,64%,and 85% from 45%,54%,and 66%,respectively.The effect of HA was also observed in the degradation of n-alkanes within 30 days.The rates of removal of n-alkanes in soil planted with B.campestris and H.annuus were high for n-alkanes in the range of C11-C28.A dynamic increase in dehydrogenase activity was observed during the last 15 days of a 30-day experimental period in all the pots amended with HA.The enhanced biodegradation performance for TPHs observed might be due to an increase in microbial activities and bioavailable TPH in soils caused by combined effects of plants and HA.The results suggested that HA could act as an enhancing agent for phytodegradation of petroleum hydrocarbons in soil contaminated with diesel fuel and heavy metals.

MOLECULAR DIAGNOSTIC RATIOS TO ASSESS THE APPORTIONMENT OF PETROLEUM HYDROCARBONS CONTAMINANTION IN MARINE SEDIMENT

Directory of Open Access Journals (Sweden)

Agung Dhamar Syakti

2016-11-01

Full Text Available As maritime fulcrum nation, in Indonesia, marine environmental analytical chemistry field is still under developed. So that why, this review paper aims to provide basic understanding of the use some molecular diagnostic indices using n-alkanes indexes and polycyclic aromatic hydrocarbons (PAHs diagnostic ratios to estimate the source of apportionment of the hydrocarbons contamination and origin. The n-alkane chromatograms were then used to characterize the predominance of petrogenic or biogenic either terrestrial or aquatic. Furthermore, characterization allowed to discriminate riverine versus marine input. The occurrence of a broad unresolved complex mixture can be an evidence of biodegraded petroleum residues. For aromatic compounds, the prevalence of petrogenic, pyrolitic, and combustion-derived can be easily plotted by using isomers ratio calculation. This paper thus provides useful information on the hydrocarbon contamination origin, especially in marine sediments. Further researches should be undertaken in order to validate the use of molecular diagnostic ratio with isotopic approach.

Influence of dispersants on trophic transfer of petroleum hydrocarbons in a marine food chain

Energy Technology Data Exchange (ETDEWEB)

Wolfe, M.; Tjeerdema, R. [Univ. of California, Santa Cruz, CA (United States). Dept. of Chemistry and Biochemistry; Sowby, M. [California Dept. of Fish and Game, Sacramento, CA (United States)

1995-12-31

When crude oil is accidentally released into the ocean, it threatens many levels of marine life. Intervention, in the form of chemical dispersing agents, alters the normal behavior of petroleum hydrocarbons (PH) by increasing their functional water solubility and the extent of their exposure to sub-surface organisms. Dispersing agents may modify bioavailability as a result of altered interactions between dispersed PH droplets and organismal cell membranes.The objective of this research was to determine the impact of dispersing agents on PH bioavailability and trophic transfer in primary levels of a marine food chain. Uptake, bioaccumulation, depuration, and metabolic transformation of a model PH, {sup 14}C-naphthalene, were measured and compared for Prudhoe Bay Crude Oil (PBCO) dispersed with Corexit 9527 and undispersed preparations of the water-accommodated fractions (WAF) of PBCO at two salinities and temperatures. The model food chain consisted of Isochrysis galbana and Brachionus plicatilis. Direct aqueous exposure was compared with combined aqueous and dietary exposure. Fractionation and identification of metabolites was done by HPLC co-chromatography with analytical standards, and quantitation was done by liquid scintillation counting. GC-FID characterization of WAF and dispersed oil (DO) preparations shows higher concentrations of petroleum hydrocarbons and a greater number of individual constituents in the dispersed oil preparations.

Influence of dispersants on trophic transfer of petroleum hydrocarbons in a marine food chain

International Nuclear Information System (INIS)

Wolfe, M.; Tjeerdema, R.

1995-01-01

When crude oil is accidentally released into the ocean, it threatens many levels of marine life. Intervention, in the form of chemical dispersing agents, alters the normal behavior of petroleum hydrocarbons (PH) by increasing their functional water solubility and the extent of their exposure to sub-surface organisms. Dispersing agents may modify bioavailability as a result of altered interactions between dispersed PH droplets and organismal cell membranes.The objective of this research was to determine the impact of dispersing agents on PH bioavailability and trophic transfer in primary levels of a marine food chain. Uptake, bioaccumulation, depuration, and metabolic transformation of a model PH, 14 C-naphthalene, were measured and compared for Prudhoe Bay Crude Oil (PBCO) dispersed with Corexit 9527 and undispersed preparations of the water-accommodated fractions (WAF) of PBCO at two salinities and temperatures. The model food chain consisted of Isochrysis galbana and Brachionus plicatilis. Direct aqueous exposure was compared with combined aqueous and dietary exposure. Fractionation and identification of metabolites was done by HPLC co-chromatography with analytical standards, and quantitation was done by liquid scintillation counting. GC-FID characterization of WAF and dispersed oil (DO) preparations shows higher concentrations of petroleum hydrocarbons and a greater number of individual constituents in the dispersed oil preparations

Natural attenuation of petroleum hydrocarbons-a study of biodegradation effects in groundwater (Vitanovac, Serbia).

Science.gov (United States)

Marić, Nenad; Matić, Ivan; Papić, Petar; Beškoski, Vladimir P; Ilić, Mila; Gojgić-Cvijović, Gordana; Miletić, Srđan; Nikić, Zoran; Vrvić, Miroslav M

2018-01-20

The role of natural attenuation processes in groundwater contamination by petroleum hydrocarbons is of intense scientific and practical interest. This study provides insight into the biodegradation effects in groundwater at a site contaminated by kerosene (jet fuel) in 1993 (Vitanovac, Serbia). Total petroleum hydrocarbons (TPH), hydrochemical indicators (O 2 , NO 3 - , Mn, Fe, SO 4 2- , HCO 3 - ), δ 13 C of dissolved inorganic carbon (DIC), and other parameters were measured to demonstrate biodegradation effects in groundwater at the contaminated site. Due to different biodegradation mechanisms, the zone of the lowest concentrations of electron acceptors and the zone of the highest concentrations of metabolic products of biodegradation overlap. Based on the analysis of redox-sensitive compounds in groundwater samples, redox processes ranged from strictly anoxic (methanogenesis) to oxic (oxygen reduction) within a short distance. The dependence of groundwater redox conditions on the distance from the source of contamination was observed. δ 13 C values of DIC ranged from - 15.83 to - 2.75‰, and the most positive values correspond to the zone under anaerobic and methanogenic conditions. Overall, results obtained provide clear evidence on the effects of natural attenuation processes-the activity of biodegradation mechanisms in field conditions.

Comparison of analytical methods used to measure petroleum hydrocarbons in soils and their application to bioremediation studies

International Nuclear Information System (INIS)

Douglas, G.S.; Wong, W.M.; Rigatti, M.J.; McMillen, S.J.

1995-01-01

Chemical measurements provide a means to evaluate crude oil and refined product bioremediation effectiveness in field and laboratory studies. These measurements are used to determine the net decrease in product or target compound concentrations in complex soil systems. The analytical methods used to evaluate these constituents will have a direct impact on the ability of the investigator to; (1) detect losses due to biodegradation, (2) understand the processes responsible for the hydrocarbon degradation and, (3) determine the rates of hydrocarbon degradation. This understanding is critical for the testing and design of bioremediation programs. While standard EPA methods are useful for measuring a wide variety of industrial and agrochemicals, they were not designed for the detection and accurate measurement of petroleum compounds. The chemical data generated with these standard methods are usually of limited utility because they lack the chemical specificity required to evaluate hydrocarbon compositional changes in the oil contamination required to evaluate biodegradation. The applications and limitations of standard EPA methodologies (EPA Methods 418.1, 8270, and modified 8015) will be evaluated and compared to several new analytical methods currently being used by the petroleum industry (e.g., gross compositional analysis, TLC-FID analysis, and enhanced EPA Method 8270) to evaluate bioremediation effectiveness in soils

Phytoremediation of petroleum hydrocarbons by using a freshwater fern species Azolla filiculoides Lam.

Science.gov (United States)

Kösesakal, Taylan; Ünal, Muammer; Kulen, Oktay; Memon, Abdülrezzak; Yüksel, Bayram

2016-01-01

In this study, the phytoremediation capacity of Azolla filiculoides Lam. for the water resources contaminated with petroleum hydrocarbons was investigated. The plants were grown in nitrogen-free Hoagland nutrient solution containing 0.005%, 0.01%, 0.05%, 0.1%, 0.2%, 0.3%, 0.4%, and 0.5% crude oil under greenhouse conditions for 15 days. Although the growth rate of the plants were not negatively influenced by the presence of crude oil in the media for the concentration of 0.005% and 0.01% v/v, a gradual impeding effect of crude oil in the growth media has been observed at concentrations 0.05-0.1%. More than 0.1% crude oil in the growth medium ostensibly retarded the growth. For example, 0.2% oil in the media reduced growth approximately 50% relative to the control, and the presence of crude oil at concentrations 0.3% or more were lethal. The data about the percentage of plant growth, fresh weight increase and root growth clearly indicated that the tolerance level of A. filiculoides plants to crude oil ranges between 0.1% and 0.2%. In comparison to control samples, the biodegradation rate of total aliphatic and aromatic (phenathrene) hydrocarbons at 0.05-0.2% oil concentrations, was 94-73% and 81-77%, respectively. On the other hand, in case of further increases in oil concentration in media, i.e.; 0.3-0.5%, the biodegradation rate was still higher in the experimental samples, respectively 71-63% and 75-71%. The high biodegradation rates of petroleum hydrocarbons in the experimental samples suggested that A. filiculoides plants could be a promising candidate to be used for the phytoremediation of low crude oil contaminated precious freshwater resources.

The petroleum industry in 2003

International Nuclear Information System (INIS)

2004-01-01

This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

Petroleum potential of two sites in Deaf Smith and Swisher Counties, Texas Panhandle: Volume 1: Technical report

International Nuclear Information System (INIS)

Rose, P.R.

1986-09-01

This is the third in a series of regional geologic studies to assess the petroleum resources of two potentially acceptable sites under study for a nuclear waste disposal facility. Site 1 is in northeastern Deaf Smith County, Texas, and Site 2 is in northeastern Swisher County, Texas. Although potential reservoir zones are present under Site 1, the likelihood of hydrocarbon charge and structural or stratigraphic entrapment is low. The probability of a commercial petroleum discovery is estimated at 1:1000, and expected net present value of potential production is about $700,000. Little future industry drilling activity is foreseen around Site 1. Five potential reservoir zones are present under Site 2, and some may contain hydrocarbons. Anticlines are adjacent to Site 2, and some may contain hydrocarbons. Anticlines are adjacent to Site 2 on the northeast, southeast, and northwest, but the middle of the acreage block is synclinal, and its petroleum potential is very low. Discovery probability of the structures adjacent to Site 2 is higher, but the chance of developing commercial production is only about 2:100. Such accumulations might extend into the northeast and southeast corners of the block; expected net present value of such conjectured reserves is about $1,100,000 and $650,000, respectively. Continued industry activity pursuant to these three structures is expected, including seismic surveys and drilling. Considering the potential loss of petroleum resources through withdrawal of acreage from exploration, and the possibility of adjacent drilling, Site 1 in Deaf Smith County is clearly preferable for location of the proposed nuclear waste disposal facility

Bioremediation of oil-contaminated soil using Candida catenulata and food waste.

Science.gov (United States)

Joo, Hung-Soo; Ndegwa, Pius M; Shoda, Makoto; Phae, Chae-Gun

2008-12-01

Even though petroleum-degrading microorganisms are widely distributed in soil and water, they may not be present in sufficient numbers to achieve contaminant remediation. In such cases, it may be useful to inoculate the polluted area with highly effective petroleum-degrading microbial strains to augment the exiting ones. In order to identify a microbial strain for bioaugmentation of oil-contaminated soil, we isolated a microbial strain with high emulsification and petroleum hydrocarbon degradation efficiency of diesel fuel in culture. The efficacy of the isolated microbial strain, identified as Candida catenulata CM1, was further evaluated during composting of a mixture containing 23% food waste and 77% diesel-contaminated soil including 2% (w/w) diesel. After 13 days of composting, 84% of the initial petroleum hydrocarbon was degraded in composting mixes containing a powdered form of CM1 (CM1-solid), compared with 48% of removal ratio in control reactor without inoculum. This finding suggests that CM1 is a viable microbial strain for bioremediation of oil-contaminated soil with food waste through composting processes.

The analysis of semi-volatile and non-volatile petroleum hydrocarbons in a soil/sediment matrix by capillary column gas chromatography/flame ionization detection (GC/FID)

International Nuclear Information System (INIS)

George, J.E. III; Thoma, J.J.; Hastings, M.

1990-01-01

A comprehensive analysis for semi-volatile and non-volatile fractions of petroleum hydrocarbons can be achieved by a solvent extraction/concentration techniques that will effectively extract these high molecular weight fractions from a soil matrix. The prepared extract is then injected directly into a gas chromatograph equipped with a capillary column and flame ionization detector. This technique applies to the following types of commercially available petroleum hydrocarbons: Diesel Nos. 2,4,5, and 6, fuel oils and several grades of lubrication oil. The identification of a particular petroleum hydrocarbon is determined visually by comparison of the samples with known hydrocarbon standards. Accurate quantitation of the chromatograms is possible by using peak area summation and the presence of an internal standard. The practical quantitation limit for the method is 10 mg/Kg for most fuel types. This paper presents a method for determining the concentration of these fuel types in soil. Data will be presented only on 10W40 lubrication oil in terms of method validation, calibration, percent recovery, and method detection limits. A discussion of the quatitation techniques used will also be included

Validating potential toxicity assays to assess petroleum hydrocarbon toxicity in polar soil.

Science.gov (United States)

Harvey, Alexis Nadine; Snape, Ian; Siciliano, Steven Douglas

2012-02-01

Potential microbial activities are commonly used to assess soil toxicity of petroleum hydrocarbons (PHC) and are assumed to be a surrogate for microbial activity within the soil ecosystem. However, this assumption needs to be evaluated for frozen soil, in which microbial activity is limited by liquid water (θ(liquid)). Influence of θ(liquid) on in situ toxicity was evaluated and compared to the toxicity endpoints of potential microbial activities using soil from an aged diesel fuel spill at Casey Station, East Antarctica. To determine in situ toxicity, gross mineralization and nitrification rates were determined by the stable isotope dilution technique. Petroleum hydrocarbon-contaminated soil (0-8,000 mg kg(-1)), packed at bulk densities of 1.4, 1.7, and 2.0 g cm(-3) to manipulate liquid water content, was incubated at -5°C for one, two, and three months. Although θ(liquid) did not have a significant effect on gross mineralization or nitrification, gross nitrification was sensitive to PHC contamination, with toxicity decreasing over time. In contrast, gross mineralization was not sensitive to PHC contamination. Toxic response of gross nitrification was comparable to potential nitrification activity (PNA) with similar EC25 (effective concentration causing a 25% effect in the test population) values determined by both measurement endpoints (400 mg kg(-1) for gross nitrification compared to 200 mg kg(-1) for PNA), indicating that potential microbial activity assays are good surrogates for in situ toxicity of PHC contamination in polar regions. Copyright © 2011 SETAC.

A study of light hydrocarbons (C{sub 4}-C{sub 1}3) in source rocks and petroleum fluid

Energy Technology Data Exchange (ETDEWEB)

Odden, Wenche

2000-07-01

This thesis consists of an introduction and five included papers. Of these, four papers are published in international journals and the fifth was submitted for review in April 2000. Emphasis has been placed on both naturally and artificially generated light hydrocarbons in petroleum fluids and their proposed source rocks as well as direct application of light hydrocarbons to oil/source rock correlations. Collectively, these papers describe a strategy for interpreting the source of the light hydrocarbons in original oils and condensates as well as the source of the asphaltene fractions from the reservoir fluids. The influence of maturity on light hydrocarbon composition has also been evaluated. The papers include (1) compositional data on the light hydrocarbons from thermal extracts and kerogen pyrolysates of sediment samples, (2) light hydrocarbon data of oils and condensates as well as the pyrolysis products of the asphaltenes from these fluids, (3) assessment of compositional alteration effects, such as selective losses of light hydrocarbons due to evaporation, thermal maturity, phase fractionation and biodegradation, (4) comparison of naturally and artificially generated light hydrocarbons, and (5) compound-specific carbon isotope analysis of the whole range of hydrocarbons of all sample types. (author)

Evaluation of the effectiveness of different methods for the remediation of contaminated groundwater by determining the petroleum hydrocarbon content

Energy Technology Data Exchange (ETDEWEB)

Voyevoda, Maryna; Geyer, Wolfgang; Mothes, Sibylle [Department of Analytical Chemistry, UFZ, Helmholtz Centre for Environmental Research - UFZ, Leipzig (Germany); Mosig, Peter [Centre for Environmental Biotechnology, UFZ, Helmholtz Centre for Environmental Research - UFZ, Leipzig (Germany); Seeger, Eva M. [Department of Environmental Biotechnology, UFZ, Helmholtz Centre for Environmental Research - UFZ, Leipzig (Germany)

2012-08-15

The effectiveness of different remediation procedures for decreasing the amount of TPH (total petroleum hydrocarbons) in contaminated groundwater was evaluated at the site of a former refinery. The investigations were carried out on samples taken from several gravel based HSSF (horizontal subsurface flow) constructed wetlands (CW) which differed in relation to their filter material additives (no additive, charcoal, and ferric oxides additives) and examined the potential effect of these additives on the overall treatment efficiency. Samples of the following gravel based HSSF CW were investigated. No filter additive (system A), 0.1% activated carbon (system B), 0.5% iron(III) hydroxide (system C), and the reference (system D). Systems A-C were planted with common reed (Phragmites australis), whereas system D remained unplanted. In addition, the influence of seasonal conditions on the reduction of these hydrocarbons and the correlation between the amounts of TPH and BTEX (benzene, toluene, ethylbenzene, and xylene isomers), on the one hand, and methyl tert-butyl ether, on the other, was investigated. The study was carried out by using a modified GC-FID approach and multivariate methods. The investigations carried out in the first year of operation demonstrated that the effectiveness of the petroleum hydrocarbon removal was highest and reached a level of 93 {+-} 3.5% when HSSF filters with activated carbon as a filter additive were used. This remediation method allowed the petroleum hydrocarbon content to be reduced independently of seasonal conditions. The correlation between the reduction of TPH and BTEX was found to be R = 0.8824. Using this correlation coefficient, the time-consuming determination of the BTEX content was no longer necessary. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The potential for hydrocarbon biodegradation and production of extracellular polymeric substances by aerobic bacteria isolated from a Brazilian petroleum reservoir.

Science.gov (United States)

Vasconcellos, S P; Dellagnezze, B M; Wieland, A; Klock, J-H; Santos Neto, E V; Marsaioli, A J; Oliveira, V M; Michaelis, W

2011-06-01

Extracellular polymeric substances (EPS) can contribute to the cellular degradation of hydrocarbons and have a huge potential for application in biotechnological processes, such as bioremediation and microbial enhanced oil recovery (MEOR). Four bacterial strains from a Brazilian petroleum reservoir were investigated for EPS production, emulsification ability and biodegradation activity when hydrocarbons were supplied as substrates for microbial growth. Two strains of Bacillus species had the highest EPS production when phenanthrene and n-octadecane were offered as carbon sources, either individually or in a mixture. While Pseudomonas sp. and Dietzia sp., the other two evaluated strains, had the highest hydrocarbon biodegradation indices, EPS production was not detected. Low EPS production may not necessarily be indicative of an absence of emulsifier activity, as indicated by the results of a surface tension reduction assay and emulsification indices for the strain of Dietzia sp. The combined results gathered in this work suggest that a microbial consortium consisting of bacteria with interdependent metabolisms could thrive in petroleum reservoirs, thus overcoming the limitations imposed on each individual species by the harsh conditions found in such environments.

Separation of motor oils, oily wastes and hydrocarbons from contaminated water by sorption on chrome shavings.

Science.gov (United States)

Gammoun, A; Tahiri, S; Albizane, A; Azzi, M; Moros, J; Garrigues, S; de la Guardia, M

2007-06-25

In this paper, the ability of chrome shavings to remove motor oils, oily wastes and hydrocarbons from water has been studied. To determine amount of hydrocarbons sorbed on tanned wastes, a FT-NIR methodology was used and a multivariate calibration based on partial least squares (PLS) was employed for data treatment. The light density, porous tanned waste granules float on the surface of water and remove hydrocarbons and oil films. Wastes fibers from tannery industry have high sorption capacity. These tanned solid wastes are capable of absorbing many times their weight in oil or hydrocarbons (6.5-7.6g of oil and 6.3g of hydrocarbons per gram of chrome shavings). The removal efficiency of the pollutants from water is complete. The sorption of pollutants is a quasi-instantaneous process.

Hazardous Waste Management System - Identification and Listing of Hazardous Waste - Toxicity Characteristic - Hydrocarbon Recovery Operations - Federal Register Notice, February 1, 1991

Science.gov (United States)

Extends the compliance date of the Toxicity Characteristic until January 25, 1991 for groundwater that is reinjected or reinfiltrated during existing hydrocarbon recovery operations at petroleum refineries, marketing terminals, and bulk plants.

The petroleum industry in 2005

International Nuclear Information System (INIS)

2006-01-01

This document provides information on the petroleum industry for the year 2005. It discusses the world gas and petroleum markets, the world and french petroleum exploration and production, the petroleum and byproducts industry in France, the hydrocarbons supplying, the refining in France, the evolution of the products and fuels substitution quality, the internal transports of petroleum products, the storage consumption and taxes of petroleum products, the prices and distribution of the petroleum products. (A.L.B.)

Evaluation of gastrointestinal solubilization of petroleum hydrocarbon residues in soil using an in vitro physiologically based model.

Science.gov (United States)

Holman, Hoi-Ying N; Goth-Goldstein, Regine; Aston, David; Yun, Mao; Kengsoontra, Jenny

2002-03-15

Petroleum hydrocarbon residues in weathered soils may pose risks to humans through the ingestion pathway. To understand the factors controlling their gastrointestinal (GI) absorption, a newly developed experimental extraction protocol was used to model the GI solubility of total petroleum hydrocarbon (TPH) residues in highly weathered soils from different sites. The GI solubility of TPH residues was significantly higher for soil contaminated with diesel than with crude oil. Compared to the solubility of TPH residues during fasted state,the solubility of TPH residues during fat digestion was much greater. Diesel solubility increased from an average of 8% during the "gallbladder empty" phase of fasting (and less than 0.2% during the otherfasting phase) to an average of 16% during fat digestion. For crude oil, the solubility increased from an average of 1.2% during the gallbladder empty phase of fasting (and undetectable during the other fasting phase) to an average of 4.5% during fat digestion. Increasing the concentration of bile salts also increased GI solubility. GI solubility was reduced by soil organic carbon but enhanced by the TPH content.

Metal accumulation in the polychaete Hediste japonica with emphasis on interaction between heavy metals and petroleum hydrocarbons

International Nuclear Information System (INIS)

Sun Fuhong; Zhou Qixing

2007-01-01

The accumulation of cadmium (Cd) and copper (Cu) in the polychaete Hediste japonica exposed to the mixture of Cd (or Cu) and petroleum hydrocarbons (PHCs) was investigated and compared with that exposed to single Cd (or Cu). The increased bioavailability of Cd or Cu with exposure concentrations resulted in an increase in the accumulation and net accumulation rate of Cd or Cu during single metal exposure. The net accumulation rate of Cd increased, but the net accumulation rate of Cu decreased with exposure time during single metal exposure, suggesting that H. japonica could actively regulate Cu burden in their body by inhibition of absolute uptake or promotion of excretion. The interactions between Cd (or Cu) and PHCs had complicated influences on the net accumulation rate of Cd and Cu in H. japonica under the condition of the binary mixture, which are dependent on their concentration combinations and exposure time. - The influences of petroleum hydrocarbons on Cd and Cu accumulation in H. japonica depend on their concentration combinations and exposure time

Assessment of intra-species diversity among strains of Acinetobacter baumannii isolated from sites contaminated with petroleum hydrocarbons

International Nuclear Information System (INIS)

Manab Sarma, P.; Bhattacharya, D.; Krishnan, S.; Lal, B.

2004-01-01

Intra-species diversity among Acinetobacter baumannii strains isolated from crude oil-contaminated soils from different geographic regions in India was assessed, including their capability to degrade different fractions of total petroleum hydrocarbons. A total of 96 strains were isolated from five different sites. Of the 96 isolates, 25 strains were identified as Acinetobacter baumannii; all of these strains were biochemically profiled and grouped into eight phenovars on the basis of multivariate analysis of their substrate utilization profiles. All strains were able to degrade the total petroleum hydrocarbon fractions of crude oil. Intraspecies relatedness among the 25 strains was determined using tRNA intergenic spacer length polymorphism. Specific variants among the strains with different degradation capacities for different fractions of crude oil were detected. Environmental influences that cause intra-species diversity, such as functional resilience, within the selected strains of A. baumannii were also noted. It is suggested that such diversities may make it possible to select contaminant-specific strains for efficient biotechnological strategies in environmental remediation. 19 refs., 4 tabs., 3 figs

Assessment of intra-species diversity among strains of Acinetobacter baumannii isolated from sites contaminated with petroleum hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Manab Sarma, P.; Bhattacharya, D.; Krishnan, S. [TERI School of Advanced Studies, Center of Bioresources and Biotechnology, New Delhi (India); Lal, B. [TERI School of Advanced Studies, Microbial Biotechnology Division, New Delhi (India)

2004-06-01

Intra-species diversity among Acinetobacter baumannii strains isolated from crude oil-contaminated soils from different geographic regions in India was assessed, including their capability to degrade different fractions of total petroleum hydrocarbons. A total of 96 strains were isolated from five different sites. Of the 96 isolates, 25 strains were identified as Acinetobacter baumannii; all of these strains were biochemically profiled and grouped into eight phenovars on the basis of multivariate analysis of their substrate utilization profiles. All strains were able to degrade the total petroleum hydrocarbon fractions of crude oil. Intraspecies relatedness among the 25 strains was determined using tRNA intergenic spacer length polymorphism. Specific variants among the strains with different degradation capacities for different fractions of crude oil were detected. Environmental influences that cause intra-species diversity, such as functional resilience, within the selected strains of A. baumannii were also noted. It is suggested that such diversities may make it possible to select contaminant-specific strains for efficient biotechnological strategies in environmental remediation. 19 refs., 4 tabs., 3 figs.

Mangrove microniches determine the structural and functional diversity of enriched petroleum hydrocarbon-degrading consortia.

Science.gov (United States)

Gomes, Newton C M; Flocco, Cecilia G; Costa, Rodrigo; Junca, Howard; Vilchez, Ramiro; Pieper, Dietmar H; Krögerrecklenfort, Ellen; Paranhos, Rodolfo; Mendonça-Hagler, Leda C S; Smalla, Kornelia

2010-11-01

In this study, the combination of culture enrichments and molecular tools was used to identify bacterial guilds, plasmids and functional genes potentially important in the process of petroleum hydrocarbon (PH) decontamination in mangrove microniches (rhizospheres and bulk sediment). In addition, we aimed to recover PH-degrading consortia (PHDC) for future use in remediation strategies. The PHDC were enriched with petroleum from rhizosphere and bulk sediment samples taken from a mangrove chronically polluted with oil hydrocarbons. Southern blot hybridization (SBH) assays of PCR amplicons from environmental DNA before enrichments resulted in weak positive signals for the functional gene types targeted, suggesting that PH-degrading genotypes and plasmids were in low abundance in the rhizosphere and bulk sediments. However, after enrichment, these genes were detected and strong microniche-dependent differences in the abundance and composition of hydrocarbonoclastic bacterial populations, plasmids (IncP-1α, IncP-1β, IncP-7 and IncP-9) and functional genes (naphthalene, extradiol and intradiol dioxygenases) were revealed by in-depth molecular analyses [PCR-denaturing gradient gel electrophoresis and hybridization (SBH and microarray)]. Our results suggest that, despite the low abundance of PH-degrading genes and plasmids in the environmental samples, the original bacterial composition of the mangrove microniches determined the structural and functional diversity of the PHDC enriched. © 2010 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

Hydrocarbon composition products of the catalytic recycling plastics waste

Directory of Open Access Journals (Sweden)

Zhaksyntay Kairbekov

2013-09-01

Full Text Available The paper represents the IR spectroscopy results of the hydrocarbon composition of products, which is obtained from catalytic processing of plastic wastes. The optimal conditions for the hydrogenation with to producny liquid of products are identified.  These liquid products are enriched with aromatics, paraffinic- naphthenic and unsaturated hydrocarbons. The main characteristics of the distillates received by hydrogenation of plastics (as density, refractive index, iodine number, pour point, cloud point, filtering, sulfur content,  fractional and composition of the hydrocarbon group.

Partnership in an application of RBCA: Case study for quantitative assessment of total petroleum hydrocarbons

International Nuclear Information System (INIS)

Srinivasan, K.; Shepherd, D.

1995-01-01

Risk-Based Corrective Action (RBCA) was successfully applied at a site contaminated with weathered Total Petroleum Hydrocarbons (TPH) from a past release of Diesel Fuel No. 2. In partnership with the state regulatory agency, an approach was developed to assess the toxicity of TPH by the evaluation of its individual classes/constituents. Historically, assessments of petroleum product releases have focused solely on TPH as an analytical parameter and not its individual fractions and/or constituents which represent the actual toxicity of the released product. Soil and groundwater TPH data by Modified California Method 8015 (GC/MS) were reviewed. Based on analytical standards, typical Diesel Fuel No. 2 carbon ranges/fractions were identified. In addition, site-specific carbon-chain lengths were identified based on the aforementioned standard. In consultation with state regulators and according to state draft RBCA guidance, site-specific polycyclic aromatic hydrocarbons (PAHs) and three TPH carbon-range fractions were identified as constituents of concern. In order to quantify the three TPH fractions, appropriate toxicological surrogates were identified. Site-specific exposures to potential human and ecological receptors were evaluated in close consultation with the state regulators. Limited contaminant fate and transport analysis was conducted. Subsequently, complete exposure pathways were quantified

PGPR enhanced phytoremediation of petroleum contaminated soil and rhizosphere microbial community response.

Science.gov (United States)

Hou, Jinyu; Liu, Wuxing; Wang, Beibei; Wang, Qingling; Luo, Yongming; Franks, Ashley E

2015-11-01

The aim of this study was to investigate petroleum phytoremediation enhancement by plant growth promoting bacteria (PGPR), specifically the correlation between petroleum hydrocarbon fractions and bacterial community structure affected by remediation and PGPR inocula. Aged petroleum contaminated soil was remediated by tall fescue (Testuca arundinacea L.) inoculated with two PGPR strains. Hydrocarbon degradation was measured by GC-MS (Gas-chromatography Mass-spectrometer) based on carbon fraction numbers (C8-C34). Changes in bacterial community structure were analyzed by high-throughput pyrosequencing of 16s rRNA. PGPR inoculation increased tall fescue biomass and petroleum hydrocarbons were removed in all the treatments. Maximum hydrocarbon removal, particular high molecular weight (C21-C34) aliphatic hydrocarbons (AHs) and polycyclic aromatic hydrocarbons (PAHs), was observed in tall fescue inoculated with PGPR. The relative abundance of phyla γ-proteobacteria and Bacteroidetes increased after different treatments compared with controls. Moreover, a bacterial guild mainly comprising the genera Lysobacter, Pseudoxanthomonas, Planctomyces, Nocardioides, Hydrogenophaga, Ohtaekwangia was found to be positively correlated with C21-C34 petroleum hydrocarbons fractions removal by RDA analysis, implying that petroleum degradation was unrelated to bacterial community diversity but positively correlated with specific petroleum degraders and biosurfactant producers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Removal of polycyclic aromatic hydrocarbons in soil spiked with model mixtures of petroleum hydrocarbons and heterocycles using biosurfactants from Rhodococcus ruber IEGM 231.

Science.gov (United States)

Ivshina, Irina; Kostina, Ludmila; Krivoruchko, Anastasiya; Kuyukina, Maria; Peshkur, Tatyana; Anderson, Peter; Cunningham, Colin

2016-07-15

Removal of polycyclic aromatic hydrocarbons (PAHs) in soil using biosurfactants (BS) produced by Rhodococcus ruber IEGM 231 was studied in soil columns spiked with model mixtures of major petroleum constituents. A crystalline mixture of single PAHs (0.63g/kg), a crystalline mixture of PAHs (0.63g/kg) and polycyclic aromatic sulfur heterocycles (PASHs), and an artificially synthesized non-aqueous phase liquid (NAPL) containing PAHs (3.00g/kg) dissolved in alkanes C10-C19 were used for spiking. Percentage of PAH removal with BS varied from 16 to 69%. Washing activities of BS were 2.5 times greater than those of synthetic surfactant Tween 60 in NAPL-spiked soil and similar to Tween 60 in crystalline-spiked soil. At the same time, amounts of removed PAHs were equal and consisted of 0.3-0.5g/kg dry soil regardless the chemical pattern of a model mixture of petroleum hydrocarbons and heterocycles used for spiking. UV spectra for soil before and after BS treatment were obtained and their applicability for differentiated analysis of PAH and PASH concentration changes in remediated soil was shown. The ratios A254nm/A288nm revealed that BS increased biotreatability of PAH-contaminated soils. Copyright © 2016 Elsevier B.V. All rights reserved.

Hazardous Waste Management System - Identification and Listing of Hazardous Waste - Toxicity Characteristic - Hydrocarbon Recovery Operations - Federal Register Notice, April 2, 1991

Science.gov (United States)

Proposal to extend the compliance date for the Toxicity Characteristic until January 25, 1993 for produced groundwater from free phase hydrocarbon recovery operations at certain petroleum industry sites-namely, refineries, marketing terminals, bulk plants.

Fate and degradation of petroleum hydrocarbons in stormwater bioretention cells

Science.gov (United States)

LeFevre, Gregory Hallett

This dissertation describes the investigation of the fate of hydrocarbons in stormwater bioretention areas and those mechanisms that affect hydrocarbon fate in such systems. Seventy-five samples from 58 bioretention areas were collected and analyzed to measure total petroleum hydrocarbon (TPH) residual and biodegradation functional genes. TPH residual in bioretention areas was greater than background sites but low overall (hydrocarbon biodegradation. Field soils were capable of mineralizing naphthalene, a polycyclic aromatic hydrocarbon (PAH) when incubated in the laboratory. In an additional laboratory investigation, a column study was initiated to comprehensively determine naphthalene fate in a simulated bioretention cell using a 14C-labeled tracer. Sorption to soil was the greatest sink of naphthalene in the columns, although biodegradation and vegetative uptake were also important loss mechanisms. Little leaching occurred following the first flush, and volatilization was insignificant. Significant enrichment of naphthalene degrading bacteria occurred over the course of the experiment as a result of naphthalene exposure. This was evident from enhanced naphthalene biodegradation kinetics (measured via batch tests), significant increases in naphthalene dioxygenase gene quantities, and a significant correlation observed between naphthalene residual and biodegradation functional genes. Vegetated columns outperformed the unplanted control column in terms of total naphthalene removal and biodegradation kinetics. As a result of these experiments, a final study focused on why planted systems outperform unplanted systems was conducted. Plant root exudates were harvested from hydroponic setups for three types of plants. Additionally, a solution of artificial root exudates (AREs) as prepared. Exudates were digested using soil bacteria to create metabolized exudates. Raw and metabolized exudates were characterized for dissolved organic carbon, specific UV absorbance

Hydrocarbon pollution in the sediment from the Jarzouna-Bizerte coastal area of Tunisia (Mediterranean Sea).

Science.gov (United States)

Zrafi-Nouira, I; Khedir-Ghenim, Z; Zrafi, F; Bahri, R; Cheraeif, I; Rouabhia, M; Saidane-Mosbahi, D

2008-06-01

This study investigated the presence and origin of hydrocarbon pollution in industrial waste water sediments found near the Jarzouna (Bizerte, Tunisia) oil refinery. Analyses of surface sediments (layer 1) and deep sediments (layer 2) showed that Total Hydrocarbon (TH) concentrations ranged from 602 +/- 7.638 microg/g in layer-1 to 1270 +/- 2.176 microg/g in layer-2. The results suggest that the deeper the sediment, the higher the level of total hydrocarbon found. The sedimentary Non Aromatic Hydrocarbon (NAH) and Aromatic Hydrocarbon (AH) concentrations ranged from 66.22 +/- 1.516 to 211.82 +/- 10.670 microg/g for NAH, and from 13.84 +/- 0.180 to 115.60 +/- 2.479 microg/g for AH. The high variability of these concentrations was associated with the location of the sediment collection sites. Aliphatic biomarker analysis revealed petroleum contamination close to the refinery rejection site, and biogenic sources further away. Petroleum contamination may be associated with increased industrial activity in the area of Jarzouna-Bizerte in the Mediterranean Sea.

Analyzing tree cores to detect petroleum hydrocarbon-contaminated groundwater at a former landfill site in the community of Happy Valley-Goose Bay, eastern Canadian subarctic.

Science.gov (United States)

Fonkwe, Merline L D; Trapp, Stefan

2016-08-01

This research examines the feasibility of analyzing tree cores to detect benzene, toluene, ethylbenzene, and m, p, o-xylene (BTEX) compounds and methyl tertiary-butyl ether (MTBE) in groundwater in eastern Canada subarctic environments, using a former landfill site in the remote community of Happy Valley-Goose Bay, Labrador. Petroleum hydrocarbon contamination at the landfill site is the result of environmentally unsound pre-1990s disposal of households and industrial solid wastes. Tree cores were taken from trembling aspen, black spruce, and white birch and analyzed by headspace-gas chromatography-mass spectrometry. BTEX compounds were detected in tree cores, corroborating known groundwater contamination. A zone of anomalously high concentrations of total BTEX constituents was identified and recommended for monitoring by groundwater wells. Tree cores collected outside the landfill site at a local control area suggest the migration of contaminants off-site. Tree species exhibit different concentrations of BTEX constituents, indicating selective uptake and accumulation. Toluene in wood exhibited the highest concentrations, which may also be due to endogenous production. Meanwhile, MTBE was not found in the tree cores and is considered to be absent in the groundwater. The results demonstrate that tree-core analysis can be useful for detecting anomalous concentrations of petroleum hydrocarbons, such as BTEX compounds, in subarctic sites with shallow unconfined aquifers and permeable soils. This method can therefore aid in the proper management of contamination during landfill operations and after site closures.

A test of plant-aided petroleum hydrocarbon degradation

Energy Technology Data Exchange (ETDEWEB)

Hosler, K R [Water Technology International Corp., Burlington, ON (Canada); Drake, E N [Exxon Research Engineering Co., Annandale, NJ (United States)

1999-12-31

A research program was established to develop environmental restoration technologies which apply to contaminated industrial sites. The program involved two separate but related parts. Part One involved a multi-year field study, Part Two a greenhouse potted plant study. This paper presents the results of the greenhouse-based phytoremediation experiment which assessed the potential impacts of three treatment factors on the degradation of total petroleum hydrocarbons (TPH) in contaminated soils for use in those cases where the use of plants for restoring contaminated environments might be a simple and cost-effective clean-up alternative. This study showed that biologically-aided contaminant degradation can be enhanced by various treatments such as adding nutrients in the form of inorganic fertilizers, adding oxygen or modifying soil conditions. The study also showed that contaminant degradation can be enhanced in the rhizosphere of various plant species and that remediation of some contaminants can be achieved by exploiting the unique symbiotic relationship between some fungal species and plant roots. 22 refs., 3 tabs., 1 fig.

A test of plant-aided petroleum hydrocarbon degradation

International Nuclear Information System (INIS)

Hosler, K.R.; Drake, E.N.

1998-01-01

A research program was established to develop environmental restoration technologies which apply to contaminated industrial sites. The program involved two separate but related parts. Part One involved a multi-year field study, Part Two a greenhouse potted plant study. This paper presents the results of the greenhouse-based phytoremediation experiment which assessed the potential impacts of three treatment factors on the degradation of total petroleum hydrocarbons (TPH) in contaminated soils for use in those cases where the use of plants for restoring contaminated environments might be a simple and cost-effective clean-up alternative. This study showed that biologically-aided contaminant degradation can be enhanced by various treatments such as adding nutrients in the form of inorganic fertilizers, adding oxygen or modifying soil conditions. The study also showed that contaminant degradation can be enhanced in the rhizosphere of various plant species and that remediation of some contaminants can be achieved by exploiting the unique symbiotic relationship between some fungal species and plant roots. 22 refs., 3 tabs., 1 fig

Polycyclic Aromatic Hydrocarbons in Fine Particulate Matter Emitted from Burning Kerosene, Liquid Petroleum Gas, and Wood Fuels in Household Cookstoves

Science.gov (United States)

This study measured polycyclic aromatic hydrocarbon (PAH) composition in particulate matter emissions from residential cookstoves. A variety of fuel and cookstove combinations were examined, including: (i) liquid petroleum gas (LPG), (ii) kerosene in a wick stove, (iii) wood (10%...

Biochemical and Physical Characterization of Petroleum Hydrocarbon Contaminated Soils in Tehran

Directory of Open Access Journals (Sweden)

Mehrdad Cheraghi

2015-07-01

Full Text Available    Contamination of soil was investigated in this study from the Tehran Oil refining Co. of Iran. Fifteen soil samples were collected at several points in the Azimabad, 15 km south of Tehran City, Iran. Samples were collected at depths of 0–30 cm. Control sampleswere prepared to determinebackgroundlevels ofsoil contaminationwithpetroleumhydrocarbonsfor comparison with contaminatedsites. Total petroleum hydrocarbon (TPH and poly-aromatic hydrocarbons (PAH concentrations varied from 101334.0–101367.1 and 25321.1–25876.6 mg kg-1 respectively. The results elevated levels of TPH and PAH contents when compared with the control sample. Soil acidity (low pH of 5.3–5.9 and low electrical conductivity provided evidence of reduced metabolic activities on the affected site.Microbialgrowthrates for bacteria and fungi expressed as colony forming units were 2.62×109 and 4.14×106CFU/g soil, respectively for the contaminated and 5.76×109 and 6.83×106CFU/g soil, for the control treatments respectively. These drastic changes can have impact on the nutrient cycle and prevents the absorption of nutrients by plant root sand lead to a reduction in yield. 

Hydrocarbon Degradation in Caspian Sea Sediment Cores Subjected to Simulated Petroleum Seepage in a Newly Designed Sediment-Oil-Flow-Through System

Directory of Open Access Journals (Sweden)

Tina Treude

2017-04-01

Full Text Available The microbial community response to petroleum seepage was investigated in a whole round sediment core (16 cm length collected nearby natural hydrocarbon seepage structures in the Caspian Sea, using a newly developed Sediment-Oil-Flow-Through (SOFT system. Distinct redox zones established and migrated vertically in the core during the 190 days-long simulated petroleum seepage. Methanogenic petroleum degradation was indicated by an increase in methane concentration from 8 μM in an untreated core compared to 2300 μM in the lower sulfate-free zone of the SOFT core at the end of the experiment, accompanied by a respective decrease in the δ13C signal of methane from -33.7 to -49.5‰. The involvement of methanogens in petroleum degradation was further confirmed by methane production in enrichment cultures from SOFT sediment after the addition of hexadecane, methylnapthalene, toluene, and ethylbenzene. Petroleum degradation coupled to sulfate reduction was indicated by the increase of integrated sulfate reduction rates from 2.8 SO42-m-2 day-1 in untreated cores to 5.7 mmol SO42-m-2 day-1 in the SOFT core at the end of the experiment, accompanied by a respective accumulation of sulfide from 30 to 447 μM. Volatile hydrocarbons (C2–C6 n-alkanes passed through the methanogenic zone mostly unchanged and were depleted within the sulfate-reducing zone. The amount of heavier n-alkanes (C10–C38 decreased step-wise toward the top of the sediment core and a preferential degradation of shorter (C30 was seen during the seepage. This study illustrates, to the best of our knowledge, for the first time the development of methanogenic petroleum degradation and the succession of benthic microbial processes during petroleum passage in a whole round sediment core.

Hydrocarbon Degradation in Caspian Sea Sediment Cores Subjected to Simulated Petroleum Seepage in a Newly Designed Sediment-Oil-Flow-Through System.

Science.gov (United States)

Mishra, Sonakshi; Wefers, Peggy; Schmidt, Mark; Knittel, Katrin; Krüger, Martin; Stagars, Marion H; Treude, Tina

2017-01-01

The microbial community response to petroleum seepage was investigated in a whole round sediment core (16 cm length) collected nearby natural hydrocarbon seepage structures in the Caspian Sea, using a newly developed Sediment-Oil-Flow-Through (SOFT) system. Distinct redox zones established and migrated vertically in the core during the 190 days-long simulated petroleum seepage. Methanogenic petroleum degradation was indicated by an increase in methane concentration from 8 μM in an untreated core compared to 2300 μM in the lower sulfate-free zone of the SOFT core at the end of the experiment, accompanied by a respective decrease in the δ 13 C signal of methane from -33.7 to -49.5‰. The involvement of methanogens in petroleum degradation was further confirmed by methane production in enrichment cultures from SOFT sediment after the addition of hexadecane, methylnapthalene, toluene, and ethylbenzene. Petroleum degradation coupled to sulfate reduction was indicated by the increase of integrated sulfate reduction rates from 2.8 SO 4 2- m -2 day -1 in untreated cores to 5.7 mmol SO 4 2- m -2 day -1 in the SOFT core at the end of the experiment, accompanied by a respective accumulation of sulfide from 30 to 447 μM. Volatile hydrocarbons (C2-C6 n -alkanes) passed through the methanogenic zone mostly unchanged and were depleted within the sulfate-reducing zone. The amount of heavier n -alkanes (C10-C38) decreased step-wise toward the top of the sediment core and a preferential degradation of shorter (C30) was seen during the seepage. This study illustrates, to the best of our knowledge, for the first time the development of methanogenic petroleum degradation and the succession of benthic microbial processes during petroleum passage in a whole round sediment core.

Biodegradation studies of oil sludge containing high hydrocarbons concentration

International Nuclear Information System (INIS)

Olguin-Lora, P.; Munoz-Colunga, A.; Castorena-Cortes, G.; Roldan-Carrillo, T.; Quej Ake, L.; Reyes-Avila, J.; Zapata-Penasco, I.; Marin-Cruz, J.

2009-01-01

Oil industry has a significant impact on environment due to the emission of, dust, gases, waste water and solids generated during oil production all the way to basic petrochemical product manufacturing stages. the aim of this work was to evaluate the biodegradation of sludge containing high hydrocarbon concentration originated by a petroleum facility. A sludge sampling was done at the oil residuals pool (ORP) on a gas processing center. (Author)

Degradation of Total Petroleum Hydrocarbon (TPH) in Contaminated Soil Using Bacillus pumilus MVSV3.

Science.gov (United States)

Varma, Surendra Sheeba; Lakshmi, Mahalingam Brinda; Rajagopal, Perumalsam; Velan, Manickam

2017-01-01

　A study on bioremediation of soil contaminated with petroleum sludge was performed using Bacillus pumilus/MVSV3 (Accession number JN089707). In this study, 5 kg of agricultural soil was mixed well with 5% oil sludge and fertilizers containing nitrogen, phosphorus and potassium (N:P:K). The treatment resulted in 97% removal of total petroleum hydrocarbon (TPH) in 122 d in bacteria mixed contaminated soil when compared to 12% removal of TPH in uninoculated contaminated soil. The population of the microorganism remained stable after introduced into the oil environment. The physical and chemical parameters of the soil mixed with sludge showed variation indicating improvement and the pH level decreased during the experiment period. Elemental analysis and Gas Chromatography-Mass Spectroscopy (GC-MS) analysis revealed the bacterial ability to degrade oil sludge components. Growth experiments with Trigonellafoenumgraecum (Fenugreek) showed the applicability of bioremediated soil for the production.

Petroleum.

Science.gov (United States)

McManus, T. R.; And Others

1989-01-01

This review of petroleum covers: crude oil; fuels, gaseous and liquid; lubricants, oils, and greases; asphalts, bitumens, tars, and pitches; hydrocarbons; physical properties; metals in oil; nonmetallic elements and heterocompounds; and analytical methods and apparatus. (MVL)

High paraffin Kumkol petroleum processing under fuel and lubricant petroleum scheme

International Nuclear Information System (INIS)

Nadirov, N.K.; Konaev, Eh.N.

1997-01-01

Technological opportunity of high paraffin Kumkol petroleum processing under the fuel and lubricant scheme with production of lubricant materials in short supply, combustible materials and technical paraffin is shown. Mini petroleum block putting into operation on Kumkol deposit is reasonable economically and raises profitableness of hydrocarbon raw material production. (author)

Evaluation of phytoremediation of petroleum hydrocarbon and heavy metals with using Catharanthus roseus

Directory of Open Access Journals (Sweden)

Mehri Askary Mehrabadi

2014-08-01

Full Text Available Crude oil pollution is an inevitable worldwide phenomenon in oil producing and consuming areas that stems from human error, accidental discharge and other sources. The aim of this study was to evaluate the phytoremediation potential of vinca in petroleum-polluted soil. The experiment was laid out as a completely randomized design in 3 replications with different concentrations of crude oil (0, 0.5, 1, 2, 3 and 4 % V/W in pot planting stage. At the end of the 70-day period, soil samples were analyzed for total hydrocarbons removal. Contents of pb, zn and Ni were measured by atomic absorption from the soils and the leaves. Statistical analysis of data were performed on the basis of duncan’s test and by using of SPSS16 software. In concentrations higher than 3 % no growth was observed. The growth parameters such as stem length, stem fresh and dry matter decreased progressively from 0.5-3 % crude oil in soil. The results showed heavy metal accumulation in plant leaves and reduction of them in the soil. Heavy metals containing zinc, lead and nickel in plant increased in different concentration of crude oil. Total hydrocarbons and heavy metals containing zinc, lead and nickel reduced were in planted contaminated soil. This study showed that Periwinkle was able to grow and survive in low concentrations of oil and reduced pollutants in the soil. Based upon these results, Catharanthus roseus can be used as phytoremediator of petroleum-contaminated soil in low concentrations.

Determination of radioactivity in petroleum products and wastes

International Nuclear Information System (INIS)

Hrichi, Hajer

2009-01-01

At this end engineering study, we determined the activities of gamma- emitting radionuclides belonging to the families of 238 U, 235 U, 232 Th and 40K in the petroleum products and wastes of the refinery S.T.I.R. The activities of radionuclides which exceed that of crude oil prove that it's a technologically enhanced natural radioactivity since several chemical products were injected during the refining process. (Author)

Biotechnological Potential of Bacillus salmalaya 139SI: A Novel Strain for Remediating Water Polluted with Crude Oil Waste

OpenAIRE

Ismail, Salmah; Dadrasnia, Arezoo

2015-01-01

Environmental contamination by petroleum hydrocarbons, mainly crude oil waste from refineries, is becoming prevalent worldwide. This study investigates the bioremediation of water contaminated with crude oil waste. Bacillus salamalaya 139SI, a bacterium isolated from a private farm soil in the Kuala Selangor in Malaysia, was found to be a potential degrader of crude oil waste. When a microbial population of 108 CFU ml-1 was used, the 139SI strain degraded 79% and 88% of the total petroleum hy...

Petroleum hydrocarbon biodegradation under seasonal freeze-thaw soil temperature regimes in contaminated soils from a sub-Arctic site.

Science.gov (United States)

Chang, Wonjae; Klemm, Sara; Beaulieu, Chantale; Hawari, Jalal; Whyte, Lyle; Ghoshal, Subhasis

2011-02-01

Several studies have shown that biostimulation in ex situ systems such as landfarms and biopiles can facilitate remediation of petroleum hydrocarbon contaminated soils at sub-Arctic sites during summers when temperatures are above freezing. In this study, we examine the biodegradation of semivolatile (F2: C10-C16) and nonvolatile (F3: C16-C34) petroleum hydrocarbons and microbial respiration and population dynamics at post- and presummer temperatures ranging from -5 to 14 °C. The studies were conducted in pilot-scale tanks with soils obtained from a historically contaminated sub-Arctic site in Resolution Island (RI), Canada. In aerobic, nutrient-amended, unsaturated soils, the F2 hydrocarbons decreased by 32% during the seasonal freeze-thaw phase where soils were cooled from 2 to -5 °C at a freezing rate of -0.12 °C d(-1) and then thawed from -5 to 4 °C at a thawing rate of +0.16 °C d(-1). In the unamended (control) tank, the F2 fraction only decreased by 14% during the same period. Biodegradation of individual hydrocarbon compounds in the nutrient-amended soils was also confirmed by comparing their abundance over time to that of the conserved diesel biomarker, bicyclic sesquiterpanes (BS). During this period, microbial respiration was observed, even at subzero temperatures when unfrozen liquid water was detected during the freeze-thaw period. An increase in culturable heterotrophs and 16S rDNA copy numbers was noted during the freezing phase, and the (14)C-hexadecane mineralization in soil samples obtained from the nutrient-amended tank steadily increased. Hydrocarbon degrading bacterial populations identified as Corynebacterineae- and Alkanindiges-related strains emerged during the freezing and thawing phases, respectively, indicating there were temperature-based microbial community shifts.

The effect of salinity, redox mediators and temperature on anaerobic biodegradation of petroleum hydrocarbons in microbial fuel cells

Energy Technology Data Exchange (ETDEWEB)

Adelaja, Oluwaseun, E-mail: o.adelaja@my.westminster.ac.uk; Keshavarz, Tajalli, E-mail: t.keshavarz@westminster.ac.uk; Kyazze, Godfrey, E-mail: g.kyazze@westminster.ac.uk

2015-02-11

Highlights: • Effective degradation of petroleum hydrocarbon mixtures was achieved using MFC. • Adapted anaerobic microbial consortium was used as inoculum. • Bio-electricity generation was enhanced by 30-fold when riboflavin, was added. • Optimum MFC performance was obtained at mesophilic and moderately saline conditions. • Stable MFC performance was obtained during prolonged fed-batch MFC operation. - Abstract: Microbial fuel cells (MFCs) need to be robust if they are to be applied in the field for bioremediation. This study investigated the effect of temperature (20–50 °C), salinity (0.5–2.5% (w/v) as sodium chloride), the use of redox mediators (riboflavin and anthraquinone-2-sulphonate, AQS) and prolonged fed-batch operation (60 days) on biodegradation of a petroleum hydrocarbon mix (i.e. phenanthrene and benzene) in MFCs. The performance criteria were degradation efficiency, % COD removal and electrochemical performance. Good electrochemical and degradation performance were maintained up to a salinity of 1.5% (w/v) but deteriorated by 35-fold and 4-fold respectively as salinity was raised to 2.5%w/v. Degradation rates and maximum power density were both improved by approximately 2-fold at 40 °C compared to MFC performance at 30 °C but decreased sharply by 4-fold when operating temperature was raised to 50 °C. The optimum reactor performance obtained at 40 °C was 1.15 mW/m{sup 2} maximum power density, 89.1% COD removal and a degradation efficiency of 97.10%; at moderately saline (1% w/v) conditions the maximum power density was 1.06 mW/m{sup 2}, 79.1% COD removal and 91.6% degradation efficiency. This work suggests the possible application of MFC technology in the effective treatment of petroleum hydrocarbons contaminated site and refinery effluents.

The effect of salinity, redox mediators and temperature on anaerobic biodegradation of petroleum hydrocarbons in microbial fuel cells

International Nuclear Information System (INIS)

Adelaja, Oluwaseun; Keshavarz, Tajalli; Kyazze, Godfrey

2015-01-01

Highlights: • Effective degradation of petroleum hydrocarbon mixtures was achieved using MFC. • Adapted anaerobic microbial consortium was used as inoculum. • Bio-electricity generation was enhanced by 30-fold when riboflavin, was added. • Optimum MFC performance was obtained at mesophilic and moderately saline conditions. • Stable MFC performance was obtained during prolonged fed-batch MFC operation. - Abstract: Microbial fuel cells (MFCs) need to be robust if they are to be applied in the field for bioremediation. This study investigated the effect of temperature (20–50 °C), salinity (0.5–2.5% (w/v) as sodium chloride), the use of redox mediators (riboflavin and anthraquinone-2-sulphonate, AQS) and prolonged fed-batch operation (60 days) on biodegradation of a petroleum hydrocarbon mix (i.e. phenanthrene and benzene) in MFCs. The performance criteria were degradation efficiency, % COD removal and electrochemical performance. Good electrochemical and degradation performance were maintained up to a salinity of 1.5% (w/v) but deteriorated by 35-fold and 4-fold respectively as salinity was raised to 2.5%w/v. Degradation rates and maximum power density were both improved by approximately 2-fold at 40 °C compared to MFC performance at 30 °C but decreased sharply by 4-fold when operating temperature was raised to 50 °C. The optimum reactor performance obtained at 40 °C was 1.15 mW/m 2 maximum power density, 89.1% COD removal and a degradation efficiency of 97.10%; at moderately saline (1% w/v) conditions the maximum power density was 1.06 mW/m 2 , 79.1% COD removal and 91.6% degradation efficiency. This work suggests the possible application of MFC technology in the effective treatment of petroleum hydrocarbons contaminated site and refinery effluents

Horizontal arrangement of anodes of microbial fuel cells enhances remediation of petroleum hydrocarbon-contaminated soil.

Science.gov (United States)

Zhang, Yueyong; Wang, Xin; Li, Xiaojing; Cheng, Lijuan; Wan, Lili; Zhou, Qixing

2015-02-01

With the aim of in situ bioremediation of soil contaminated by hydrocarbons, anodes arranged with two different ways (horizontal or vertical) were compared in microbial fuel cells (MFCs). Charge outputs as high as 833 and 762C were achieved in reactors with anodes horizontally arranged (HA) and vertically arranged (VA). Up to 12.5 % of the total petroleum hydrocarbon (TPH) was removed in HA after 135 days, which was 50.6 % higher than that in VA (8.3 %) and 95.3 % higher than that in the disconnected control (6.4 %). Hydrocarbon fingerprint analysis showed that the degradation rates of both alkanes and polycyclic aromatic hydrocarbons (PAHs) in HA were higher than those in VA. Lower mass transport resistance in the HA than that of the VA seems to result in more power and more TPH degradation. Soil pH was increased from 8.26 to 9.12 in HA and from 8.26 to 8.64 in VA, whereas the conductivity was decreased from 1.99 to 1.54 mS/cm in HA and from 1.99 to 1.46 mS/cm in VA accompanied with the removal of TPH. Considering both enhanced biodegradation of hydrocarbon and generation of charge in HA, the MFC with anodes horizontally arranged is a promising configuration for future applications.

Analysis of soils contaminated with petroleum constituents

International Nuclear Information System (INIS)

O'Shay, T.A.; Hoddinott, K.

1994-01-01

This symposium was held in Atlanta, Georgia on June 24, 1993. The purpose of the symposium was to provide a forum for exchange of information on petroleum contaminated soils. When spilled on the ground, petroleum products can cause massive problems in the environment. In this Special Technical Publication (STP), papers were selected in two categories; the analytical procedures for soil contaminated with petroleum hydrocarbons and the behavior of hydrocarbon contaminated soils. Individual papers have been processed separately for inclusion in the appropriate data bases

Changes in hydrocarbon groups, soil ecotoxicity and microbiology along horizontal and vertical contamination gradients in an old landfarming field for oil refinery waste

International Nuclear Information System (INIS)

Mikkonen, Anu; Hakala, Kati P.; Lappi, Kaisa; Kondo, Elina; Vaalama, Anu; Suominen, Leena

2012-01-01

Horizontal and vertical contaminant gradients in an old landfarming field for oil refinery waste were characterised with the aim to assess parallel changes in hydrocarbon groups and general, microbiological and ecotoxicological soil characteristics. In the surface soil polar compounds were the most prevalent fraction of heptane-extractable hydrocarbons, superseding GC–FID-resolvable and high-molar-mass aliphatics and aromatics, but there was no indication of their relatively higher mobility or toxicity. The size of the polar fraction correlated poorly with soil physical, chemical and microbiological properties, which were better explained by the total heptane-extractable and total petroleum hydrocarbons (TPH). Deleterious effects on soil microbiology in situ were observed at surprisingly low TPH concentrations (0.3%). Due to the accumulation of polar and complexed degradation products, TPH seems an insufficient measure to assess the quality and monitor the remediation of soil with weathered hydrocarbon contamination. - Highlights: ► Weathered hydrocarbon contamination and soil quality on landfarm site were studied. ► Silica fractionation of hydrocarbons separated aliphatics, aromatics and polars. ► Polar hydrocarbon metabolites had accumulated in the surface soil. ► Total hydrocarbons and TPH correlated with soil quality changes better than polars. ► Toxic response of soil microbial biomass and activity were seen at low TPH (<0.5%). - Polar metabolites constitute the largest fraction of crude oil-derived contaminants in a landfarming site, but TPH better explains soil microbial and ecotoxicological responses.

Analysis of ORC (Organic Rankine Cycle) systems with pure hydrocarbons and mixtures of hydrocarbon and retardant for engine waste heat recovery

International Nuclear Information System (INIS)

Song, Jian; Gu, Chun-wei

2015-01-01

The Organic Rankine Cycle (ORC) has been demonstrated to be a promising technology for the recovery of engine waste heat. Systems with hydrocarbons as the working fluids exhibit good thermal performance. However, the flammability of hydrocarbons limits their practical applications because of safety concerns. This paper examines the potential of using mixtures of a hydrocarbon and a retardant in an ORC system for engine waste heat recovery. Refrigerants R141b and R11 are selected as the retardants and blended with the hydrocarbons to form zeotropic mixtures. The flammability is suppressed, and in addition, zeotropic mixtures provide better temperature matches with the heat source and sink, which reduces the exergy loss within the heat exchange processes, thereby increasing the cycle efficiency. Energetic and exergetic analysis of ORC systems with pure hydrocarbons and with mixtures of a hydrocarbon and a retardant are conducted and compared. The net power output and the second law efficiency are chosen as the evaluation criteria to select the suitable working fluid compositions and to define the optimal set of thermodynamic parameters. The simulation results reveal that the ORC system with cyclohexane/R141b (0.5/0.5) is optimal for this engine waste heat recovery case, thereby increasing the net power output of the system by 13.3% compared to pure cyclohexane. - Highlights: • ORC with zeotropic mixtures for engine waste heat recovery is discussed. • Energetic and exergetic analysis of ORC system are conducted. • Optimal mixture working fluid composition is identified. • Greater utilization of jacket water and lower irreversible loss are important.

Hydrocarbon pollution from marinas in estuarine sediments

Science.gov (United States)

Voudrias, Evangelos A.; Smith, Craig L.

1986-03-01

A measure of the impact of marinas on three Eastern Virginia estuarine creeks was obtained by a study of hydrocarbons in their sediments. Two of the creeks support considerable marine activity, including pleasure boat marinas, boat repair facilities, and commercial fishing operations. The third creek, which served as a control, is seldom used by boats, and is surrounded by marsh and woodland. Sediments from the creeks with marinas contained significantly higher levels of both aromatic and aliphatic hydrocarbons than did the control. Differences in the concentrations of certain oil-pollution indicators, such as the 17α,21β-hopane homologs and phytane, and low molecular weight aromatic hydrocarbons, are indicative of light petroleum fractions. Most of the aromatic hydrocarbons from all creeks, however, appear to have a pyrogenic origin. Although hydrocarbons from three probable origins (petroleum, pyrogenesis, and recent biosynthesis) were detected in all locations, the petroleum-derived and pyrogenic hydrocarbons were of only minor importance relative to the biogenic hydrocarbons in the control creek.

An assessment of the disposal of radioactive petroleum industry waste in nonhazardous landfills using risk-based modeling

International Nuclear Information System (INIS)

Smith, K.P.; Arnish, J.J.; Williams, G.P.; Blunt, D.L.

2003-01-01

Certain petroleum production activities cause naturally occurring radioactive materials (NORM) to accumulate in concentrations above natural background levels, making safe and cost-effective management of such technologically enhanced NORM (TENORM) a key issue for the petroleum industry. As a result, both industry and regulators are interested in identifying cost-effective disposal alternatives that provide adequate protection of human health and the environment. One such alternative, currently allowed in Michigan with restrictions, is the disposal of TENORM wastes in nonhazardous waste landfills. The disposal of petroleum industry wastes containing radium-226 (Ra-226) in nonhazardous landfills was modeled to evaluate the potential radiological doses and health risks to workers and the public. Multiple scenarios were considered in evaluating the potential risks associated with landfill operations and the future use of the property. The scenarios were defined, in part, to evaluate the Michigan policy; sensitivity analyses were conducted to evaluate the impact of key parameters on potential risks. The results indicate that the disposal of petroleum industry TENORM wastes in nonhazardous landfills in accordance with the Michigan policy and existing landfill regulations presents a negligible risk to most of the potential receptors considered in this study.

The use of rockfish Sebastiscus marmoratus as a sentinel species to assess petroleum hydrocarbons pollution: A case study in Quanzhou Bay, China.

Science.gov (United States)

Bo, Jun; Zheng, Ronghui; Kuang, Weiming; Hong, Fukun; Xie, Qing; Zhang, Yusheng

2017-11-30

To monitor the biological effects of marine pollution, choosing a native fish species and establishing suitable biomarkers are required. In this study, the full-length cDNA of cyp1a1 was cloned from Sebastiscus marmoratus (SM-CYP1A1). Then the dose-response and time-course induction of hepatic CYP1A1 mRNA by the crude oil water-soluble fraction (WSF) were determined. Subsequently, SM-CYP1A1 mRNA was applied to investigate the biological effect of petroleum hydrocarbon pollution in Quanzhou Bay, China. The transcription levels of hepatic CYP1A1 were significantly elevated in fish caged in the polluted sites for 2weeks compared with those of the reference site, which were correlated with the concentrations of petroleum hydrocarbon and polycyclic aromatic hydrocarbon (PAH) in the surface seawaters. The results suggest that S. marmoratus is a potential sentinel organism to monitor marine pollutants and the hepatic CYP1A1 mRNA can serve as a sensitive biomarker to organic xenobiotics in aquatic environments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of genotoxic responses of Chaetoceros tenuissimus and Skeletonema costatum to water accommodated fraction of petroleum hydrocarbons as biomarker of exposure

Digital Repository Service at National Institute of Oceanography (India)

Desai, S.R.; Verlecar, X.N.; Ansari, Z.A.; Jagtap, T.G.; Sarkar, A.; Vashistha, D.; Dalal, S.G.

by water accommodated fraction of petroleum hydrocarbons was assessed in terms of the DNA integrity measured by alkaline unwinding assay. The comparative study of the growth pattern of C. tenuissimus with respect to DNA integrity and the DNA strand breaks...

Fixation of petroleum contaminated soils via cold-mix asphalt for use as a liner

International Nuclear Information System (INIS)

Testa, S.M.; Patton, D.L.; Conca, J.L.

1992-01-01

This paper reports on several methodologies which are available for the remediation of petroleum hydrocarbon-affected soils (PHAS) including bioremediation vapor extraction, chemical fixation and direct disposal. A proven alternative for the fixation of petroleum-contaminated soils is via combination with cold-mix asphalt. One viable and creative use which is within the intent and spirit of current regulations is producing, in lieu of a landfill waste, an end-product for use as a cap, liner or other site-specific application. Consideration of certain factors including durability, aging, permeability and leachability suggests that cold-mix asphalt incorporation petroleum-contaminated soils will perform more than adequately under normal conditions for a long period of time - probably more than 1,000 years

Using Ramped Pyrolysis - Gas Chromatography - Mass Spectrometry to Evaluate Petroleum Hydrocarbons Following the Deepwater Horizon Oil Spill

Science.gov (United States)

Evans, M.; Rosenheim, B. E.; Bacosa, H. P.; Liu, J.; Liu, Z.

2016-02-01

In summer of 2010, the Deepwater Horizon oil spill polluted hundreds of miles of coastline along the Gulf of Mexico. A combination of human-mediated and natural weathering processes then altered the chemical composition (i.e. toxicity) of this spilled crude oil over time and space. One of the most important, yet challenging, aspects of oil spill science is to quantify these chemical changes in natural environments. In this study, we develop ramped pyrolysis - gas chromatography - mass spectrometry (Py-GC-MS) to address this challenge. In this technique, 0.1mg of freeze-dried sample is pyrolyzed over a gradual temperature ramp (50-650°C). The eluded gas is cold-trapped over different thermal ranges (a.k.a. thermal slicing) and each range is individually analyzed via GC-MS, yielding quantifiable, compound-specific results. Py-GC-MS with thermal slicing has never been used for petroleum hydrocarbon analysis, but it has many advantages - it uses minimal sample, is time efficient and does not require sample preparation (minimizing compound loss and increasing the analytical window). During development of this method, we analyzed oiled sediments and tar collected on Grand Isle, Louisiana from 2010-2012. We quantified n-alkane (C10-C38), polycyclic aromatic hydrocarbon (PAH) and hopane content and confirmed these results with traditional solvent extraction, silica gel fractionation and mass spectrometry. Overall, we found rapid depletion of n-alkanes and PAHs (>90% depletion) in all samples within one year of Deepwater Horizon. After this, n-alkanes were almost 100% depleted by 2012, while PAH degradation continued to a maximum total degradation of 99% and 98% in sediment and tar, respectively. This not only describes the fate of petroleum compounds in salt marshes and beach deposits over time, but also complements previous radiocarbon studies of the same samples showing different rates of degradation in different micro-environments. In addition, the results presented

Biotechnological potential of Bacillus salmalaya 139SI: a novel strain for remediating water polluted with crude oil waste.

Science.gov (United States)

Ismail, Salmah; Dadrasnia, Arezoo

2015-01-01

Environmental contamination by petroleum hydrocarbons, mainly crude oil waste from refineries, is becoming prevalent worldwide. This study investigates the bioremediation of water contaminated with crude oil waste. Bacillus salamalaya 139SI, a bacterium isolated from a private farm soil in the Kuala Selangor in Malaysia, was found to be a potential degrader of crude oil waste. When a microbial population of 108 CFU ml-1 was used, the 139SI strain degraded 79% and 88% of the total petroleum hydrocarbons after 42 days of incubation in mineral salt media containing 2% and 1% of crude oil waste, respectively, under optimum conditions. In the uninoculated medium containing 1% crude oil waste, 6% was degraded. Relative to the control, the degradation was significantly greater when a bacteria count of 99 × 108 CFU ml-1 was added to the treatments polluted with 1% oil. Thus, this isolated strain is useful for enhancing the biotreatment of oil in wastewater.

Biotechnological potential of Bacillus salmalaya 139SI: a novel strain for remediating water polluted with crude oil waste.

Directory of Open Access Journals (Sweden)

Salmah Ismail

Full Text Available Environmental contamination by petroleum hydrocarbons, mainly crude oil waste from refineries, is becoming prevalent worldwide. This study investigates the bioremediation of water contaminated with crude oil waste. Bacillus salamalaya 139SI, a bacterium isolated from a private farm soil in the Kuala Selangor in Malaysia, was found to be a potential degrader of crude oil waste. When a microbial population of 108 CFU ml-1 was used, the 139SI strain degraded 79% and 88% of the total petroleum hydrocarbons after 42 days of incubation in mineral salt media containing 2% and 1% of crude oil waste, respectively, under optimum conditions. In the uninoculated medium containing 1% crude oil waste, 6% was degraded. Relative to the control, the degradation was significantly greater when a bacteria count of 99 × 108 CFU ml-1 was added to the treatments polluted with 1% oil. Thus, this isolated strain is useful for enhancing the biotreatment of oil in wastewater.

Hydrocarbons derived from petroleum in bottled drinking water from Mexico City.

Science.gov (United States)

Vega, Salvador; Gutiérrez, Rey; Ortiz, Rutilio; Schettino, Beatriz; Ramírez, Maria de Lourdes; Pérez, José Jesus

2011-06-01

This paper describes the concentrations of polycyclic aromatic hydrocarbons (PAHs) and aliphatic hydrocarbons (AHs) derived from petroleum in bottled drinking water samples that were collected over 1 year from Mexico City in two bottle sizes (1.5 and 19 L), all brought in supermarkets. The analysis was by gas chromatography with flame ionization detection. -Concentrations of AHs (9.26-1.74 μg/L) were greater than PAHs (20.15-12.78 ng/L). Individual concentrations of PAHs such as fluoranthene, benzo(b)fluoranthene, benzo(k)fluoranthene, indeno(1,2,3-cd)pyrene and benzo(ghi)perylene were comparable with data reported by the World Health Organization (WHO). Total concentrations of PAHs for all samples (BDW1: 12.78 μg/L, BDW2: 16.72 μg/L, BDW3: 14.62 μg/L, BDW4: 20.15 μg/L and BDW5: 13.23 ng/L) were below the maximum permissible European level of 100 ng/L; no regulations exist for AHs although their values were greater than PAHs (BDW1: 3.11 μg/L, BDW2: 8.45 μg/L, BDW3: 1.74 μg/L, BDW4: 4.75 μg/L and BDW5: 9.26 μg/L).

Bioremediation and phytoremediation of total petroleum hydrocarbons (TPH) under various conditions.

Science.gov (United States)

McIntosh, Patrick; Schulthess, Cristian P; Kuzovkina, Yulia A; Guillard, Karl

2017-08-03

Remediation of contaminated soils is often studied using fine-textured soils rather than low-fertility sandy soils, and few studies focus on recontamination events. This study compared aerobic and anaerobic treatments for remediation of freshly introduced used motor oil on a sandy soil previously phytoremediated and bioacclimated (microorganisms already adapted in the soil environment) with some residual total petroleum hydrocarbon (TPH) contamination. Vegetated and unvegetated conditions to remediate anthropogenic fill containing residual TPH that was spiked with nonaqueous phase liquids (NAPLs) were evaluated in a 90-day greenhouse pot study. Vegetated treatments used switchgrass (Panicum virgatum). The concentration of aerobic bacteria were orders of magnitude higher in vegetated treatments compared to unvegetated. Nevertheless, final TPH concentrations were low in all saturated soil treatments, and high in the presence of switchgrass. Concentrations were also low in unvegetated pots with fertilizer. Acclimated indigenous microbial communities were shown to be more effective in breaking down hydrocarbons than introducing microbes from the addition of plant treatments in sandy soils. Remediation of fresh introduced NAPLs on pre-phytoremediated and bioacclimated soil was most efficient in saturated, anaerobic environments, probably due to the already pre-established microbial associations, easily bioavailable contaminants, and optimized soil conditions for microbial establishment and survival.

Comparison of earthworm responses to petroleum hydrocarbon exposure in aged field contaminated soil using traditional ecotoxicity endpoints and 1H NMR-based metabolomics

International Nuclear Information System (INIS)

Whitfield Åslund, Melissa; Stephenson, Gladys L.; Simpson, André J.; Simpson, Myrna J.

2013-01-01

1 H NMR metabolomics and conventional ecotoxicity endpoints were used to examine the response of earthworms exposed to petroleum hydrocarbons (PHCs) in soil samples collected from a site that was contaminated with crude oil from a pipeline failure in the mid-1990s. The conventional ecotoxicity tests showed that the soils were not acutely toxic to earthworms (average survival ≥90%), but some soil samples impaired reproduction endpoints by >50% compared to the field control soil. Additionally, metabolomics revealed significant relationships between earthworm metabolic profiles (collected after 2 or 14 days of exposure) and soil properties including soil PHC concentration. Further comparisons by partial least squares regression revealed a significant relationship between the earthworm metabolomic data (collected after only 2 or 14 days) and the reproduction endpoints (measured after 63 days). Therefore, metabolomic responses measured after short exposure periods may be predictive of chronic, ecologically relevant toxicity endpoints for earthworms exposed to soil contaminants. -- Highlights: •Earthworm response to petroleum hydrocarbon exposure in soil is examined. •Metabolomics shows significant changes to metabolic profile after 2 days. •Significant relationships observed between metabolomic and reproduction endpoints. •Metabolomics may have value as a rapid screening tool for chronic toxicity. -- Earthworm metabolomic responses measured after 2 and 14 days are compared to traditional earthworm ecotoxicity endpoints (survival and reproduction) in petroleum hydrocarbon contaminated soil

Controlled release fertilizer increased phytoremediation of petroleum-contaminated sandy soil.

Science.gov (United States)

Cartmill, Andrew D; Cartmill, Donita L; Alarcón, Alejandro

2014-01-01

A greenhouse experiment was conducted to determine the effect of the application of controlled release fertilizer [(CRF) 0, 4,6, or 8 kg m(-3)] on Lolium multiflorum Lam. survival and potential biodegradation of petroleum hydrocarbons (0, 3000, 6000, or 15000 mg kg(-1)) in sandy soil. Plant adaptation, growth, photosynthesis, total chlorophyll, and proline content as well as rhizosphere microbial population (culturable heterotrophic fungal and bacterial populations) and total petroleum hydrocarbon (TPH)-degradation were determined. Petroleum induced-toxicity resulted in reduced plant growth, photosynthesis, and nutrient status. Plant adaptation, growth, photosynthesis, and chlorophyll content were enhanced by the application of CRF in contaminated soil. Proline content showed limited use as a physiological indicator of petroleum induced-stress in plants. Bacterial and filamentous fungi populations were stimulated by the petroleum concentrations. Bacterial populations were stimulated by CRF application. At low petroleum contamination, CRF did not enhance TPH-degradation. However, petroleum degradation in the rhizosphere was enhanced by the application of medium rates of CRF, especially when plants were exposed to intermediate and high petroleum contamination. Application of CRF allowed plants to overcome the growth impairment induced by the presence of petroleum hydrocarbons in soils.

Integrated environmental risk assessment for petroleum-contaminated sites - a North American case study

International Nuclear Information System (INIS)

Chen, Z.; Huang, G.H.; Chakma, A.

1998-01-01

In this study, an integrated risk assessment approach is proposed for evaluating environmental risks derived from petroleum-contaminated sites. The proposed approach is composed of (i) a hydrocarbon spill screening model (HSSM) which is used for simulating immiscible flow of released hydrocarbons in vadose zone, formation of lens in capillary fringe, dissolution of pollutants at water table, and transport of the pollutants to receptors, and (ii) a fuzzy relation analysis (FRA) model which is developed for comprehensively evaluating risks caused by a number of pollutants with different impact characteristics, based on the HSSM results. This hybrid HSSM-FRA approach was applied to a case study for a petroleum-contaminated site in western Canada, where soil and groundwater was contaminated by industrial wastes containing benzene, toluene, ethylbenzene and xylenes (BTEXs). The results suggest that the HSSM-FRA can provide insight into the potential risk to the receptor of concern downward the aquifer and can serve as a basis for further remediation-related decision analysis. (author)

Analyzing tree cores to detect petroleum hydrocarbon-contaminated groundwater at a former landfill site in the community of Happy Valley-Goose Bay, eastern Canadian subarctic

DEFF Research Database (Denmark)

Fonkwe, Merline L D; Trapp, Stefan

2016-01-01

-gas chromatography-mass spectrometry. BTEX compounds were detected in tree cores, corroborating known groundwater contamination. A zone of anomalously high concentrations of total BTEX constituents was identified and recommended for monitoring by groundwater wells. Tree cores collected outside the landfill site......This research examines the feasibility of analyzing tree cores to detect benzene, toluene, ethylbenzene, and m, p, o-xylene (BTEX) compounds and methyl tertiary-butyl ether (MTBE) in groundwater in eastern Canada subarctic environments, using a former landfill site in the remote community of Happy...... Valley-Goose Bay, Labrador. Petroleum hydrocarbon contamination at the landfill site is the result of environmentally unsound pre-1990s disposal of households and industrial solid wastes. Tree cores were taken from trembling aspen, black spruce, and white birch and analyzed by headspace...

Total petroleum hydrocarbon in the tissues of some commercially important fishes of the Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Ansari, Z.A.; Desilva, C.; Badesab, S.

anthropogenic activities is absorbed by marine organisms because of its low degradability and persistence (Vandermeulen et al., 1985). The manifestation of petroleum hydrocarbon in sea food is a serious human health hazard and needs to be studied in detail... of common pollutants causing marine pollution on the Indian coast is worked out to demonstrate whether the concentrations of these pollutants can pose problem of health hazards to common man in the coastal areas. Such information becomes handy in future...

The petroleum industry in 1999 (editorial)

International Nuclear Information System (INIS)

2001-01-01

This document deals with the petroleum activity in 1999. It provides three economic analysis. The first one concerns the petroleum industry activity in 1999 and the corresponding french energy policy. The second one presents the petroleum activity in the world. The third one presents the hydrocarbons market supplying in France. (A.L.B.)

Method for quantifying the fate of petroleum in the environment

International Nuclear Information System (INIS)

Mills, M.A.; McDonald, T.J.; Bonner, J.S.; Simon, M.A.; Autenrieth, R.L.

1999-01-01

Petroleum is a complex mixture of a wide range of hydrocarbon and non-hydrocarbon compounds of various physical and chemical properties. In recent years, the research on the fate of petroleum in the environment has required analytical methods that can provide more detailed information on the components of petroleum than traditional standard methods. The analytical method presented for aqueous, sediment, and soil samples provides several levels of information on petroleum in the environment. The Total Extractable Materials (TEM) analysis provides a gross measure of petroleum in the environment using methylene chloride extraction and gravimetric analysis. Gross composition analysis separates the methylene chloride extract into a saturate hydrocarbon, an aromatic hydrocarbon, and a polar fraction each measured gravimetrically. In contrast, the target compound analysis provides a detailed measure by GC-MS of 62 specific compounds. Normalization to the conservative compound, 17α, 21β-(H)Hopane, is incorporated into the method to reduce the effects of sample and site heterogeneity. Quality control and quality assurance procedures are integral parts of these analyses to assure the validity of the resulting data. (author)

Petroleum hydrocarbon contamination of the Southern Black Sea Shelf, Turkey.

Science.gov (United States)

Balkıs, Nuray; Aksu, Abdullah; Erşan, Mahmut S

2012-02-01

In this study, total petroleum hydrocarbon (TPH) contents and some aliphatic and aromatic hydrocarbon concentrations were analysed in coastal sediments of hot points collected from along the Southern Black Sea Shelf. Surface sediment (0-2 cm) samples were collected from the locations using a Van Veen type grab sampler in September 2008 during a cruise on the Pollution Monitoring R/V ARAR. All sampling procedures were carried out according to internationally recognized guide-lines (UNEP 1991). Samples were analysed using a UV-fluorescence spec-trophotometry (UNEP/IOC/IAEA 1992) and gas chromatog- raphy (GC) via a Hewlett-Packard HP6890N series with a selective detector (GC-MSD) after hexane/ dichloromethane extraction. The ratio C(17)/C(18) varied between 2.2 and 2.9 for the surface sediments of TRK 34Y (Samsun), TRK46 (Giresun), and TRK55 (Rize), respectively. These results showed higher marine organic matter accumulation. However, pyrolytic PAHs were found predominant in these areas. In contrast, petrogenic contributions were found at Stations TRK1 (İğneada), TRK13 (Zonguldak), TRK53 (Trabzon) and TRK61 (Hopa). TPH contents of surface sediments varied between 0.29 and 363 μg g(-1) (dry wt) throughout the shelf. The lowest values were measured at Stations TRK1 (İğneada) and TRK 19 (Bartın), whereas the highest values were found at Stations TRK13 (Zonguldak) and TRK 53 (Trabzon).

Fate and transport of petroleum hydrocarbons in the subsurface near Cass Lake, Minnesota

Science.gov (United States)

Drennan, Dina M.; Bekins, Barbara A.; Warren, Ean; Cozzarelli, Isabelle M.; Baedecker, Mary Jo; Herkelrath, William N.; Delin, Geoffrey N.; Rosenbauer, Robert J.; Campbell, Pamela L.

2010-01-01

The U.S. Geological Survey (USGS) investigated the natural attenuation of subsurface petroleum hydrocarbons leaked over an unknown number of years from an oil pipeline under the Enbridge Energy Limited Partnership South Cass Lake Pumping Station, in Cass Lake, Minnesota. Three weeks of field work conducted between May 2007 and July 2008 delineated a dissolved plume of aromatic hydrocarbons and characterized the biodegradation processes of the petroleum. Field activities included installing monitoring wells, collecting sediment cores, sampling water from wells, and measuring water-table elevations. Geochemical measurements included concentrations of constituents in both spilled and pipeline oil, dissolved alkylbenzenes and redox constituents, sediment bioavailable iron, and aquifer microbial populations. Groundwater in this area flows east-southeast at approximately 26 meters per year. Results from the oil analyses indicate a high degree of biodegradation, characterized by nearly complete absence of n-alkanes. Cass Lake oil samples were more degraded than two oil samples collected in 2008 from the similarly contaminated USGS Bemidji, Minnesota, research site 40 kilometers away. Based on 19 ratios developed for comparing oil sources, the conclusion is that the oils at the two sites appear to be from the same hydrocarbon source. In the Cass Lake groundwater plume, benzene concentrations decrease by three orders of magnitude within 150 meters (m) downgradient from the oil body floating on the water table (between well MW-10 and USGS-4 well nest). The depths of the highest benzene concentrations increase with distance downgradient from the oil, a condition typical of plumes in shallow, unconfined aquifers. Background groundwater, which is nearly saturated with oxygen, becomes almost entirely anaerobic in the plume. As at the Bemidji site, the most important biodegradation processes are anaerobic and dominated by iron reduction. The similarity between the Cass Lake and

An In Silico Approach for Evaluating a Fraction-Based, Risk Assessment Method for Total Petroleum Hydrocarbon Mixtures

Directory of Open Access Journals (Sweden)

Nina Ching Y. Wang

2012-01-01

Full Text Available Both the Massachusetts Department of Environmental Protection (MADEP and the Total Petroleum Hydrocarbon Criteria Working Group (TPHCWG developed fraction-based approaches for assessing human health risks posed by total petroleum hydrocarbon (TPH mixtures in the environment. Both organizations defined TPH fractions based on their expected environmental fate and by analytical chemical methods. They derived toxicity values for selected compounds within each fraction and used these as surrogates to assess hazard or risk of exposure to the whole fractions. Membership in a TPH fraction is generally defined by the number of carbon atoms in a compound and by a compound's equivalent carbon (EC number index, which can predict its environmental fate. Here, we systematically and objectively re-evaluate the assignment of TPH to specific fractions using comparative molecular field analysis and hierarchical clustering. The approach is transparent and reproducible, reducing inherent reliance on judgment when toxicity information is limited. Our evaluation of membership in these fractions is highly consistent (̃80% on average across various fractions with the empirical approach of MADEP and TPHCWG. Furthermore, the results support the general methodology of mixture risk assessment to assess both cancer and noncancer risk values after the application of fractionation.

Uptake of Total Petroleum Hydrocarbon (TPH) and Polycyclic Aromatic Hydrocarbons (PAHs) by Oryza sativa L. Grown in Soil Contaminated with Crude Oil.

Science.gov (United States)

Patowary, Rupshikha; Patowary, Kaustuvmani; Devi, Arundhuti; Kalita, Mohan Chandra; Deka, Suresh

2017-01-01

The purpose of this study was to determine whether total petroleum hydrocarbon (TPH) and polycyclic aromatic hydrocarbons (PAHs) present in crude oil contaminated sites are transferred to roots, shoots and finally the grains of rice crops (Oryza sativa L.) grown in those sites. Soil was artificially contaminated with crude oil at concentrations of 0, 1000, 5000, 10,000, and 15,000 mg/kg, followed by planting of rice seedlings. After harvest, TPH in plant samples were measured, and it was determined that the uptake of TPH by the plants gradually increased as the concentration of oil in soil increased. Further, from GC-MS analysis, it was observed that PAHs including naphthalene and phenanthrene bioaccumulated in rice plant parts. Vital physico-chemical properties of soil were also altered due to crude oil contamination. Our study revealed that rice plants grown in crude oil polluted sites can uptake TPH including PAHs, thus emphasising the importance of prior investigation of soil condition before cultivation of crops.

Dominant petroleum hydrocarbon-degrading bacteria in the Archipelago Sea in South-West Finland (Baltic Sea) belong to different taxonomic groups than hydrocarbon degraders in the oceans.

Science.gov (United States)

Reunamo, Anna; Riemann, Lasse; Leskinen, Piia; Jørgensen, Kirsten S

2013-07-15

The natural petroleum hydrocarbon degrading capacity of the Archipelago Sea water in S-W Finland was studied in a microcosm experiment. Pristine and previously oil exposed sites were examined. Bacterial community fingerprinting was performed using terminal restriction fragment length polymorphism (T-RFLP) and samples from selected microcosms were sequenced. The abundance of PAH degradation genes was measured by quantitative PCR. Bacterial communities in diesel exposed microcosms diverged from control microcosms during the experiment. Gram positive PAH degradation genes dominated at both sites in situ, whereas gram negative PAH degrading genes became enriched in diesel microcosms. The dominant bacterial groups after a 14 days of diesel exposure were different depending on the sampling site, belonging to the class Actinobacteria (32%) at a pristine site and Betaproteobacteria (52%) at a previously oil exposed site. The hydrocarbon degrading bacteria in the Baltic Sea differ from those in the oceans, where most hydrocarbon degraders belong to Gammaproteobacteria. Copyright © 2013 Elsevier Ltd. All rights reserved.

Biodegradation of petroleum hydrocarbons in hypersaline environments

Directory of Open Access Journals (Sweden)

Luiz Fernando Martins

2012-09-01

Full Text Available Literature on hydrocarbon degradation in extreme hypersaline media presents studies that point to a negative effect of salinity increase on hydrocarbonoclastic activity, while several others report an opposite tendency. Based on information available in the literature, we present a discussion on the reasons that justify these contrary results. Despite the fact that microbial ability to metabolize hydrocarbons is found in extreme hypersaline media, indeed some factors are critical for the occurrence of hydrocarbon degradation in such environments. How these factors affect hydrocarbon degradation and their implications for the assessment of hydrocarbon biodegradation in hypersaline environments are presented in this review.

Phototoxicity of individual polycyclic aromatic hydrocarbons and petroleum to marine invertebrate larvae and juveniles

International Nuclear Information System (INIS)

Pelletier, M.C.; Burgess, R.M.; Ho, K.T.; Kuhn, A.; McKinney, R.A.; Ryba, S.A.

1997-01-01

Phototoxicity resulting from photoactivated polycyclic aromatic hydrocarbons (PAHs) has been reported in the literature for a variety of freshwater organisms. The magnitude of increase in PAH toxicity often exceeds a factor of 100. In the marine environment phototoxicity to marine organisms has not been reported for individual or complex mixtures of PAHs. In this study, larvae and juveniles of the bivalve, Mulinia lateralis, and juveniles of the mysid shrimp, Mysidopsis bahia, were exposed to individual known phototoxic PAHs (anthracene, fluoranthene, pyrene), as well as the water-accommodated fractions of several petroleum products (Fuel Oil number-sign 2, Arabian Light Crude, Prudhoe Bay Crude, Fuel Oil number-sign 6) containing PAHs. Phototoxicity of individual PAHs was 12 to >50,000 times that of conventional toxicity. Three of the petroleum products demonstrated phototoxicity while the lightest product, Fuel Oil number-sign 2, was not phototoxic at the concentrations tested. The phototoxicity of petroleum products appears to be dependent on the composition and concentrations of phototoxic PAHs present: lighter oils have fewer multiple aromatic ring, phototoxic compounds while heavier oils have higher levels of these types of molecules. This study shows that phototoxicity can occur in marine waters to marine species. Further, the occurrence of oil in marine waters presents the additional risk of phototoxicity not routinely assessed for during oil spills

Contribution of chronic petroleum inputs to Narragansett Bay and Rhode Island Sound sediments

Energy Technology Data Exchange (ETDEWEB)

Van Vleet, E S; Quin, J G

1978-05-01

Sediment cores from Narragansett Bay and Rhode Island Sound have been analyzed for petroleum hydrocarbons and compared with a relatively unpolluted sediment core from the Gulf of Maine. The sediments were analyzed for unbound hydrocarbons, hydrocarbons bound or closely associated with humic substances, and residual hydrocarbons bound or closely associated with the clay mineral or kerogen matrix. Results indicated that in general 90-100% of the hydrocarbons were in the unbound form and could be easily extracted with organic solvents. The petroleum hydrocarbons decreased with depth at all stations. Biogenic hydrocarbons (nC/sub 25/, nC/sub 27/, nC/sub 29/, and nC/sub 31/) made up an increasingly greater percentage of the total with increasing depth. The hydrocarbons in the Narragansett Bay sediments and near surface Rhode Island Sound sediments strongly resembled the hydrocarbons previously reported for the Providence River and upper Narragansett Bay. These petroleum-like hydrocarbons were shown to be largely introduced to the river and bay through chronic inputs from a municipal wastewater treatment plant. These hydrocarbons then undergo sedimentation throughout the entire bay and into Rhode Island Sound. Preliminary calculations indicate that over 0.2 million t (tonne) of petroleum hydrocarbons may be transported to the marine environment annually from municipal treatment plants. Most of these hydrocarbons appear to accumulate in estuarine and coastal sediments.

Laws of the electrochemical soils remediation from petroleum pollution

Energy Technology Data Exchange (ETDEWEB)

Korolev, V.A. [Moscow State Univ. (Russian Federation)

2001-07-01

The man-caused petroleum pollution of humus and soils in places of oil production, and also the pollution of geological environment by petroleum is carried out in growing scales. Very much frequently of ground and soils become soiled by petroleum at failures during transportation of petroleum. The humus and clay soils polluted by petroleum causes destruction ecosystems and landscapes. Therefore finding - out of the nature and mechanisms of interaction water-saturated dispersed soils with the liquid hydrocarbons becomes one of priority problems in the field of ecological geology. The development of methods of electrochemical clearing soils from the liquid hydrocarbons pollution is the important task too. Therefore, the study of dependences of a double electrical layer (DEL) parameters of the water-petroleum-saturated caolinite clay and electrochemical migration in it of petroleum was the purpose of the present work. (orig.)

Petroleum contamination movement into permafrost in the high Arctic

International Nuclear Information System (INIS)

Biggar, K.W.

1997-01-01

The extent of petroleum hydrocarbon contamination that has penetrated the active layer into the permafrost at sites where spills have occurred in Canada's Arctic was discussed. There was evidence to suggest that hydrocarbon contamination may enter the permafrost layer through gravity drainage and cap suction through fissures in the frozen soil, and perhaps by diffusion through the unfrozen water of fine-grained soils. Core samples were taken in frozen silty clay to be sectioned and analyzed for total petroleum hydrocarbons, using ultrasonic solvent extraction and gas chromatography and mass spectrometry analysis. It was concluded that it is possible for petroleum contamination in permafrost to migrate by gravity drainage down soil fissures and then diffuse into surrounding soil. 2 figs

Understanding Plant-Microbe Interactions for Phytoremediation of Petroleum-Polluted Soil

Science.gov (United States)

Nie, Ming; Wang, Yijing; Yu, Jiayi; Xiao, Ming; Jiang, Lifen; Yang, Ji; Fang, Changming; Chen, Jiakuan; Li, Bo

2011-01-01

Plant-microbe interactions are considered to be important processes determining the efficiency of phytoremediation of petroleum pollution, however relatively little is known about how these interactions are influenced by petroleum pollution. In this experimental study using a microcosm approach, we examined how plant ecophysiological traits, soil nutrients and microbial activities were influenced by petroleum pollution in Phragmites australis, a phytoremediating species. Generally, petroleum pollution reduced plant performance, especially at early stages of plant growth. Petroleum had negative effects on the net accumulation of inorganic nitrogen from its organic forms (net nitrogen mineralization (NNM)) most likely by decreasing the inorganic nitrogen available to the plants in petroleum-polluted soils. However, abundant dissolved organic nitrogen (DON) was found in petroleum-polluted soil. In order to overcome initial deficiency of inorganic nitrogen, plants by dint of high colonization of arbuscular mycorrhizal fungi might absorb some DON for their growth in petroleum-polluted soils. In addition, through using a real-time polymerase chain reaction method, we quantified hydrocarbon-degrading bacterial traits based on their catabolic genes (i.e. alkB (alkane monooxygenase), nah (naphthalene dioxygenase) and tol (xylene monooxygenase) genes). This enumeration of target genes suggests that different hydrocarbon-degrading bacteria experienced different dynamic changes during phytoremediation and a greater abundance of alkB was detected during vegetative growth stages. Because phytoremediation of different components of petroleum is performed by different hydrocarbon-degrading bacteria, plants’ ability of phytoremediating different components might therefore vary during the plant life cycle. Phytoremediation might be most effective during the vegetative growth stages as greater abundances of hydrocarbon-degrading bacteria containing alkB and tol genes were observed

Polycyclic hydrocarbon biomarkers confirm selective incorporation of petroleum in soil and kangaroo rat liver samples near an oil well blowout site in the western San Joaquin Valley, California

International Nuclear Information System (INIS)

Kaplan, I.; Lu, S.T.; Lee, R.P.; Warrick, G.

1996-01-01

Following an accidental oil well blow out at an oil field in the western part of the San Joaquin Valley, soil samples and specimens of Heermann's kangaroo rats (Dipodomys heermanni) were collected from two oil-impacted areas and one control area. Fingerprinting by GC-MS and quantitative evaluation of metabolized petroleum hydrocarbons was performed on oil, soil extracts, and rat livers. A liver from a domestically raised rabbit was used as an experimental control. The results show that there is no significant incorporation of PAHs or low molecular weight n-alkanes (C 13 --C 25 ) into the liver tissues. The C 25 --C 35 n-alkane range for all soil samples, kangaroo rat livers, and rabbit liver, is dominated by a high abundance of C 27 , C 29 , C 31 , and C 33 hydrocarbons typical of epicuticular plant waxes. In all liver tissue samples, squalene, the cholesterol precursor, is the dominant hydrocarbon. Although evidence is lacking for metabolism of PAHs and paraffinic petroleum hydrocarbons, very strong evidence is available for incorporation of a set of polycyclic hydrocarbons (biomarkers) belonging to the terpane, sterane, and monoaromatic and triaromatic sterane families, identified by ion monitoring at 191, 217, 253, and 231 m/z, respectively. Because these hydrocarbons are not known to exist in the biosphere, but are only synthesized during oil- and coal-forming processes, their presence in the liver samples constitutes proof for crude oil incorporation into tissues. This conclusion is further substantiated by the selective incorporation of only the 20S enantiomer of C 28 and C 29 steranes and aromatic steranes into the livers, with the exclusion of the 20R enantiomer. The results from the study conclusively demonstrate that polycyclic hydrocarbon biomarkers provide excellent indices for proof of petroleum exposure and metabolism in some terrestrial herbivores

ZoBell and his contributions to petroleum microbiology

International Nuclear Information System (INIS)

Bass, C.

2000-01-01

The unique contributions that microbiologist Claude ZoBell has made toward the advancement of knowledge in petroleum microbiology was discussed. His research from 1938 to 1978 has provided opportunity for improved oil recovery, modification of petroleum products, knowledge of subsurface microbiology and remediation of polluted environments. Much of his work focused on the key role of microorganisms in the diagenesis of hydrocarbon products and in enhanced oil recovery. Petroleum microbiology is divided into the following six broad areas: (1) diagenesis of organic components in sediments and subsequent oleogenesis, (2) degradation of hydrocarbons, (3) improved recovery of hydrocarbons from reservoirs, (4) modification of hydrocarbon products in formation or post production, (5) mitigation of the effects of 'nuisance organisms' during production, and (6) bioremediation of escaped crude or processed product. ZoBell recognized that oil recovery could be improved using bacterial products such as acids and gases to help mobilisation and as a control agent in oil spill pollution. 26 refs

Profiling of plants at petroleum contaminated site for phytoremediation.

Science.gov (United States)

Anyasi, Raymond Oriebe; Atagana, Harrison Ifeanyichukwu

2018-03-21

The paucity of information in the literature on the characteristics of plants that could be used for phytoremediation of petroleum hydrocarbons (PHC)-contaminated sites was the principal reason for this study. The aim of the study was to identify indigenous plants growing in PHC-impacted soil in Umuahia in eastern-Nigeria that have the ability to phytoremediate soils contaminated with hydrocarbons under tropical monsoon climate conditions. A total of 28 native plant species from different families growing in and around hydrocarbon-impacted soil in the vicinity of vandalized pipelines carrying petroleum products were collected and studied for their ability to grow in a hydrocarbon-impacted soil and remove the PHC from the impacted soil. Some of the plants demonstrated the ability to grow in soil with high levels of the total petroleum hydrocarbons (TPH), which shows that they may be tolerant to hydrocarbons in soil and could potentially phytoremediate a hydrocarbon-contaminated soil. Chromolaena odorata, Aspilia africana, Chloris barbata, Pasparlum vaginatum, Bryophyllum pinnatum, Paspalum scrobiculatum, Cosmos bipinnatus, Eragrostis atrovirens, Cyperus rotundus, and Uvaria chamae showed tendencies to phytoremediate contaminated soil. By using bioaccumulation coefficient (BAC) as a measure of phytoremediation, results showed that C. odorata, A. africana, and U. chamae demonstrated the highest potentials to phytodegrade hydrocarbons in soil.

Laboratory modeling, field study, and numerical simulation of bioremediation of petroleum contaminants

International Nuclear Information System (INIS)

Livingston, R.J.; Islam, M.R.

1999-01-01

The use of bioremediation as an alternative remediation technology is fast becoming the technique of choice among many environmental professionals. This method offers substantial benefits not found in other remediation processes. Bioremediation is very cost effective, nondestructive, relatively uncomplicated in implementing, requires nonspecialized equipment, and can be extremely effective in removing recalcitrant petroleum hydrocarbons. This study researched the availability of viable microbial populations in the arid climate in South Dakota. Exponential growth of the bacteria and the ability of bacteria to degrade long-chain hydrocarbons indicated that healthy populations do exist and could be used to mineralize organic hydrocarbons. Experimental results indicated that bioremediation can be effectively enhanced in landfills as well as in the subsurface using a supply of harmless nutrients. The biodegradation rate can be further enhanced with the use of edible surfactant that helped disperse the petroleum products. Also, the use of hydrogen peroxide enhanced the oxygen availability and increased the degradation rate. Interestingly, the bacterial growth rate was found to be high in difficult-to-biodegrade contaminants, such as waste oil. A numerical simulation program was also developed that describes the bacterial growth in the subsurface along with the reduction in substrate (contamination). Results from this program were found to be consistent with laboratory results

Large scale treatment of total petroleum-hydrocarbon contaminated groundwater using bioaugmentation.

Science.gov (United States)

Poi, Gregory; Shahsavari, Esmaeil; Aburto-Medina, Arturo; Mok, Puah Chum; Ball, Andrew S

2018-05-15

Bioaugmentation or the addition of microbes to contaminated sites has been widely used to treat contaminated soil or water; however this approach is often limited to laboratory based studies. In the present study, large scale bioaugmentation has been applied to total petroleum hydrocarbons (TPH)-contaminated groundwater at a petroleum facility. Initial TPH concentrations of 1564 mg L -1 in the field were reduced to 89 mg L -1 over 32 days. This reduction was accompanied by improved ecotoxicity, as shown by Brassica rapa germination numbers that increased from 52 at day 0 to 82% by the end of the treatment. Metagenomic analysis indicated that there was a shift in the microbial community when compared to the beginning of the treatment. The microbial community was dominated by Proteobacteria and Bacteroidetes from day 0 to day 32, although differences at the genus level were observed. The predominant genera at the beginning of the treatment (day 0 just after inoculation) were Cloacibacterium, Sediminibacterium and Brevundimonas while at the end of the treatment members of Flavobacterium dominated, reaching almost half the population (41%), followed by Pseudomonas (6%) and Limnobacter (5.8%). To the author's knowledge, this is among the first studies to report the successful large scale biodegradation of TPH-contaminated groundwater (18,000 L per treatment session) at an offshore petrochemical facility. Copyright © 2018 Elsevier Ltd. All rights reserved.

Stable isotope mass spectrometry in petroleum exploration

International Nuclear Information System (INIS)

Mathur, Manju

1997-01-01

The stable isotope mass spectrometry plays an important role to evaluate the stable isotopic composition of hydrocarbons. The isotopic ratios of certain elements in petroleum samples reflect certain characteristics which are useful for petroleum exploration

Isolation of microorganisms with chinitase, protease and keratinase activities from petroleum contaminated soils

International Nuclear Information System (INIS)

Cervantes-Gonzalez, E.; Rojas-Avelizapa, L.; Cruz-Camarillo, R.; Rojas-Avelizapa, N.G.

2005-01-01

The most important part in one process of bio-remediation are the microorganisms with the capacities to degrade target compounds, this research is based to find microorganisms hydrocarbon-clastic with enzyme activities to degrade chicken feather (keratinolytic activity) which is also a contaminant and has been used such as sorbent of petroleum and can be composted after the oil spill cleanup is complete, the isolation was also to degrade shrimp waste (chitinolitic and proteolitic activity) which is waste material that can be used in compost or such as sorbent of petroleum too. We isolated mesofilic aerobic microorganisms from mexican soils located in Tabasco, Mexico. We achieved to isolate 105 bacteria from 10 soils, 90% was Bacillus Gram (-) which are common in soils and all were hydrocarbon-clastic, only 7 different bacteria had protease and chitinase activity and 12 bacteria had keratinase activity. So we found three fungi and one actinomycete with capacity to degrade hydrocarbons and presence of chitinase activity. The results of growth and enzyme activities in liquid culture showed that the protease activity was produced between 18 and 48 h in almost all bacteria, the chitinase activity started at 12 h but was slight , only 0.5 U/ml, and the keratinase activity was produced after 6 h of incubation and there were correlation between logarithmic phase of growth and enzymes production. With this study we showed the existence of some enzyme activities from microorganisms that live in hostile habitats. This, can be useful in bio-treatment soils by the possible use of this type of residues that can be bio-degraded at the same time that the hydrocarbons increasing the speed or the quality of cleanup in soils. (authors)

Petroleum Vapor Intrusion

Science.gov (United States)

One type of vapor intrusion is PVI, in which vapors from petroleum hydrocarbons such as gasoline, diesel, or jet fuel enter a building. Intrusion of contaminant vapors into indoor spaces is of concern.

Crude oil degradation potential of bacteria isolated from oil-polluted soil and animal wastes in soil amended with animal wastes

Directory of Open Access Journals (Sweden)

Voke O. Urhibo

2017-03-01

Full Text Available The influence of animal wastes on crude oil degradation potential of strains of Proteus vulgaris and Bacillus subtilis isolated from animal wastes (poultry and pig droppings and petroleum-polluted soil was compared in laboratory studies. Both bacterial strains were selected for high crude oil degradation ability after screening many isolates by the 2,6-dichlorophenol indophenol method. Analyses by gas chromatography (GC showed that degradation of crude oil was markedly enhanced (88.3–97.3% vs 72.1–78.8% in soil amended with animal wastes as indicated by the reduction of total petroleum hydrocarbon (TPH. TPH reduction by animal waste bacterial strains in animal waste-amended soil was more than the reduction by strains from soil contaminated with petroleum (P < 0.001. The greatest reduction of TPH (96.6–97.3% vs 80.4–95.9% was by poultry waste strains and it occurred in soil amended with poultry waste. GC analyses of n-alkanes showed that although shorter chains were preferentially degraded [32.0–78.5% (C8–23 vs 6.3–18.5% (C24–36] in normal soil, biodegradation of longer chains increased to 38.4–46.3% in animal waste-amended soil inoculated with the same animal wastes’ strains. The results indicate that these animal waste strains may be of potential application for bioremediation of oil-polluted soil in the presence of the wastes from where they were isolated.

Radon effective dose from TENORM waste associated with petroleum industries

International Nuclear Information System (INIS)

Abo-Elmagd, M.; Soliman, H. A.; Daif, M. M.

2009-01-01

Technically enhanced naturally occurring radioactive material (TENORM) associated with petroleum industries can be accumulated with elevated quantities and therefore can threat the workers through external and internal exposure. Measurements of radon-related parameters give information about the radioactivity levels in the TENORM waste using the well-established correlation. Also, it is useful to calculate the internal exposure due to radon inhalation in terms of effective radon dose. Among radon-related parameters, areal exhalation rate is the most suitable for characterising land and objects with only upper surface contamination in the case of petroleum waste. The TENORM in this study is collected from waste storage areas located near oil fields at south Sinai governorate (Egypt). The average values of exhalation rates as measured by Lucas cell based on delay count method are 273 ± 144 and 38 ± 8 Bq m -2 h -1 for scale and sludge, respectively. Whereas, two count method gives results with 18 and 20 % lower values for scale and sludge, respectively with good correlation coefficient of 0.999 and 0.852, respectively. Sealed cup fitted with CR-39 gives results compatible with Lucas cell with minor deviation in case of scale due to its thoron content. The results of CR-39 are qualified by taking into consideration the correction for back diffusion effect. The effective radon dose was calculated for different simulated radioactive waste storage areas with different contaminated areas and air ventilation rate. Minimising the contaminated areas and building up efficient ventilation systems can reduce the internal exposure even in the case of RWSA-containing TENORM with elevated radioactivity. (authors)

Hydrogen or Soot?: Partial Oxidation of High-boiling Hydrocarbon Wastes

Czech Academy of Sciences Publication Activity Database

Lederer, J.; Hanika, Jiří; Nečesaný, F.; Poslední, W.; Tukač, V.; Veselý, Václav

2015-01-01

Roč. 29, č. 1 (2015), s. 5-11 ISSN 0352-9568 Institutional support: RVO:67985858 Keywords : partial oxidation * waste * hydrocarbon Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.675, year: 2015

Bioremediation of petroleum contaminated soil using vegetation--A technology transfer project

International Nuclear Information System (INIS)

Banks, M.K.; Schwab, A.P.; Govindaraju, R.S.; Chen, Z.

1994-01-01

A common environmental problem associated with the pumping and refining of crude oil is the disposal of petroleum sludge. Unfortunately, the biodegradation fate of more recalcitrant and potentially toxic contaminants, such as the polynuclear aromatic hydrocarbons (PNAs), is rapid at first but declines quickly. Biodegradation of these compounds is limited by their strong adsorption potential and low solubility. Recent research has suggested that vegetation may play an important role in the biodegradation of toxic organic chemicals, such as PNAs, in soil. The establishment of vegetation on hazardous waste sites may be an economic, effective, low maintenance approach to waste remediation and stabilization. Completed greenhouse studies have indicated that vegetative remediation is a feasible method for clean-up of surface soil contaminated with petroleum products. However, a field demonstration is needed to exhibit this new technology to the industrial community. In this project, several petroleum contaminated field sites will be chosen in collaboration with three industrial partners. These sites will be thoroughly characterized for chemical properties, physical properties, and initial PNA concentrations. A variety of plant species will be established on the sites, including warm and cool season grasses and alfalfa. Soil analyses for the target compounds over time will allow them to assess the efficiency and applicability of this remediation method

Converting petroleum into acids, soaps, etc

Energy Technology Data Exchange (ETDEWEB)

Imray, J

1883-06-19

The conversion of petroleum and hydrocarbons resulting from distillation of lignite, coal, peat, shale, etc., into organic acids by treating the hydrocarbons in the presence of caustic alkalies, alkaline earths, alkaline carbonates, or other bodies with alkaline reaction, with a current of air or oxygen, with or without pressure, at a raised temperature, and decomposing the soaps formed, the free acid being removed from the compound which is then separated into single fractions by fractional distillation or by taking advantage of the unequal solubility in petroleum or similar solvents is described.

Biodegradation of petroleum hydrocarbons at low temperatures

International Nuclear Information System (INIS)

Whyte, L. G.; Greer, C W.

1999-01-01

Bioremediation of contaminated Arctic sites has been proposed as the logistically and economically most favorable solution despite the known technical difficulties. The difficulties involve the inhibition of pollutants removal by biodegradation below freezing temperatures and the relative slowness of the process to remove enough hydrocarbon pollutants during the above-freezing summer months. Despite these formidable drawbacks, biodegradation of hydrocarbon contaminants is possible even in below-zero temperatures, especially if indigenous psychrophilic and psychrotropic micro-organism are used. This paper reports results of a study involving several hydrocarbon-degrading psychrotropic bacteria and suggests bioaugmentation with specific cold-adapted organisms and/or biostimulation with commercial fertilizers for enhancing degradation of specific contaminants in soils from northern Canada. An evaluation of the biodegradation potential of hydrocarbon contaminated soils in the high Arctic suggested that the contaminated soils contained sufficient numbers of cold-adapted hydrocarbon-degrading bacteria and that the addition of fertilizer was sufficient to enhance the level of hydrocarbon degradation at low ambient summer temperatures. 9 refs., 2 tabs., 3 figs

Geological evolution of clay sediments: the petroleum exploration vision

International Nuclear Information System (INIS)

Schneider, F.

2004-01-01

The radioactive waste isolation capacity assessment for a clay sediment host rock is link: (1) to the understanding of their present state properties and 3-D repartition (from basin evolution, including sedimentary and diagenetic process); and (2) to the prediction of their future evolution during the next million years. For petroleum exploration, basin modelling aims at reconstructing the accumulation of hydrocarbons at basin scale, and at geological timescale, taking into account the effects of kinematics displacements, sedimentation, erosion, compaction, temperatures history, overpressures and fluids flows (water and hydrocarbons). Furthermore, explorationists wish to address overpressure reconstruction in order to estimate the risks of drilling. Clay sediments are of interest for petroleum exploration because source rocks and seal are generally composed of them. Nevertheless, in spite of their occurrence in nature their evolution at geological timescale is not well understood. And, most of the knowledge has been achieved by those working in the realms of soils mechanics and civil engineering until the present geological investigations for long term radioactive waste repositories. Application of this knowledge to clay sediment is considered to be valid within the first hundreds of meters at the top of the sedimentary pile, according to a repository depth. This paper is dedicated to the sedimentary rocks behaviour at geological timescale. This behaviour is characterised by: (1) the deposition of the sediment; (2) the loading path at geological timescale; (3) the constitutive law which includes the consolidation process and the rupture criteria; and (4) the parameters evolution related to consolidation. (author)

Solo Mycoremediation Impacted by Waste Hydrocarbons

Directory of Open Access Journals (Sweden)

Franklin Santos Freire

2015-06-01

Full Text Available Oil and its derivatives are the principal means of energy generation for vehicles that transport raw materials and goods produced in developed and developing regions accentuating the risk of accidents by spills in stockpiling, transport, use or discarding. The contamination by total hydrocarbons suggests the elevated propension to mutations and to the formation of carcinogenic tumors, as a consequence of the exposure to human contamination by these products. This work had as aims: a To investigate, in a laboratorial scale, the degrading capacity of autochthonous microbiota in the presence of differing concentrations of hydrocarbons (0%, 2,5%, 5% e 7,5%; b To isolate fungi tolerant to the contaminant; c To quantify and analyze the biodegradation capacity of soil through the microbial biomass and metabolic quotient; and d To set, in laboratory, ideal conditions of biodegradation of the xenobiotic compound. Some parameters of microbial activity have been evaluated, such as: biological (Carbon of microbial biomass, CO2 , qCO2 emission, and fungi growth, chemical (pH, electrical conductivity –EC –, analysis of fertility and total hydrocarbons and physical (physical composition of the soil for analysis and comparisons. The obtained results suggest that the adding of 5% of waste oil in the ground provided ideal condition for the biodegradation of he   contaminant in the environment. From the evaluated parameters, the emission of CO2 and microbial C were considered more indicative of changes in soil microbial activity subject to the addition of hydrocarbons, confirming the possibility of microremediation use.

Effect of petroleum hydrocarbons on algae

International Nuclear Information System (INIS)

Bhadauria, S.; Sengar, R.M.S.; Mittal, S.; Bhattacharjee, S.

1992-01-01

Algal species (65) were isolated from oil refinery effluent. Twenty-five of these species were cultured in Benecke's medium in a growth chamber, along with controls. Retardation in algal growth, inhibition in algal photosynthesis, and discoloration was observed in petroleum enriched medium. Few forms, viz. Cyclotella sp., Cosmarium sp., and Merismopedia sp. could not survive. The lag phase lengthened by several days and slope of exponential phase was also depressed. Chlamydomonas sp., Scenedesmus sp., Ankistrodesmus sp., Nitzschia sp. and Navicula sp. were comparatively susceptible to petroleum. Depression in carbon fixation, cell numbers, and total dry algal mass was noticeable, showing toxicity to both diatoms and green algae

Dermal uptake of petroleum substances.

Science.gov (United States)

Jakasa, Ivone; Kezic, Sanja; Boogaard, Peter J

2015-06-01

Petroleum products are complex substances comprising varying amounts of linear and branched alkanes, alkenes, cycloalkanes, and aromatics which may penetrate the skin at different rates. For proper interpretation of toxic hazard data, understanding their percutaneous absorption is of paramount importance. The extent and significance of dermal absorption of eight petroleum substances, representing different classes of hydrocarbons, was evaluated. Literature data on the steady-state flux and permeability coefficient of these substances were evaluated and compared to those predicted by mathematical models. Reported results spanned over 5-6 orders of magnitude and were largely dependent on experimental conditions in particular on the type of the vehicle used. In general, aromatic hydrocarbons showed higher dermal absorption than more lipophilic aliphatics with similar molecular weight. The results showed high variation and were largely influenced by experimental conditions emphasizing the need of performing the experiments under "in use" scenario. The predictive models overestimated experimental absorption. The overall conclusion is that, based on the observed percutaneous penetration data, dermal exposure to petroleum hydrocarbons, even of aromatics with highest dermal absorption is limited and highly unlikely to be associated with health risks under real use scenarios. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Development of a waste minimization plan for the Department of Energy's Naval petroleum reserve No. 3

International Nuclear Information System (INIS)

Falconer, K.L.; Lane, T.C.

1991-01-01

A Waste Minimization Program Plan for the U.S. Department of Energy's (DOE) Naval Petroleum Reserve No. 3 (NPR-3) was prepared in response to DOE Order 5400.1, open-quotes General Environmental Protection Program close-quote The NPR-3 Waste Minimization Program Plan encompasses all ongoing operations at the Naval Petroleum Reserve and is consistent with the principles set forth in the mission statement for NPR-3. The mission of the NPR-3 is to apply project management, engineering and scientific capabilities to produce oil and gas from subsurface zones at the maximum efficiency rate for the United States Government. NPR-3 generates more than 60 discrete waste streams, many of significant volume. Most of these waste streams are categorized as wastes from the exploration, development and production of oil and gas and, as such, are exempt from Subtitle C of RCRA as indicated in the regulatory determination published in the Federal Register on July 6, 1988. However, because so many of these waste streams contain hazardous substances and because of an increasingly more restrictive regulatory environment, in 1990 an overall effort was made to characterize all waste streams produced and institute the best waste management practice economically practical to reduce the volume and toxicity of the waste generated

Petroleum industry. 1997 activity report; L`industrie Petroliere. Rapport d`activite 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

This activity report from the direction of hydrocarbons of the French general direction of energy and raw materials (ministry of economy, finances and industry) presents an economic analysis of the activities of the French petroleum industry for 1997. After a recall of the missions of the direction of hydrocarbons, the report analyses successively: 1- the evolution of the petroleum market: the international petroleum market in 1997, the hydrocarbon supplies and external trade (natural gas, crude oil, condensates), the French petroleum market (primary energy consumption, final energy consumption, French petroleum consumption, the petroleum logistics in overseas departments and territories), the prices, margins and fiscal policy in France and Europe (crude oil and refined product prices in the international market, retail prices in France and Europe, the French petroleum fiscal policy, statistics of petroleum prices in France and Europe; 2- the petroleum industry activities: exploration and production in France and worldwide, the maritime and domestic transports and the storage (French commercial fleet, domestic transports, storage facilities, strategic stocks), the refining activity and the quality of products and fuel substitutes (refining, automotive fuels quality, bio-fuels), the distribution of petroleum products (automotive and diesel fuels, LPG, aircraft fuels, lubricants); 3- the environmental and safety aspects of refining, transportation (pipelines, tanker-ships) and exploration-production; 4- the economic situation of the companies: petroleum groups, French para-petroleum industry, scientific and technical research. (J.S.)

Ecotoxicological assessment of bioremediation of a petroleum hydrocarbon-contaminated soil

International Nuclear Information System (INIS)

Renoux, A.Y.; Tyagi, R.D.; Samson, R.

1995-01-01

A battery of bioassays [barley seed germination, barley plant growth, lettuce seed germination, worm mortality, Microtox reg-sign, lettuce root elongation, algae Selenastrum capricornutum growth, Daphnia magna mortality, and SOS Chromotest (±S9)] was used to assess an above-ground heap pile treatment of a soil contaminated with aliphatic petroleum hydrocarbons (12 to 24 carbons). Despite an initial oil and grease concentration of 2,000 mg/kg, no significant (geno)toxicity was apparent in the soil sample before treatment. During the treatment, which decreased oil and grease concentrations to 800 mg/kg, slight toxicity was revealed by three bioassays (barley seed germination, worm mortality, Daphnia magna mortality), and a significant increase in genotoxicity was measured with the SOS Chromotest (± S9). It appears that ecotoxicological evaluation revealed harmful condition(s) that were not detected by chemical assessment. This suggests that the remediation had ceased before complete detoxification occurred. This phenomenon must be further investigated, however, to furnish solid conclusions on the toxicological effectiveness of the biotreatment

Laboratory Scale Bioremediation of Petroleum Hydrocarbon – Polluted Mangrove Swamps in the Niger Delta Using Cow Dung

Directory of Open Access Journals (Sweden)

Dike, E. N.

2012-01-01

Full Text Available Aims: The aim of the study was to carry-out laboratory–scale bioremediation of petroleum hydrocarbon polluted mangrove swamps using cow dung as source of limiting of nutrients.Methodology and Results: In a 70 days study, the cow dung treated polluted soil had its total culturable hydrocarbon utilising bacterial/fungi, heterotrophic bacterial and fungal counts increased progressively from the 28th day to the 70th day. The control set- up showed very slight increment in its microbial growth. Alkaline pH was observed in all the treatments and control during the study period. The conductivity values of cow dung decreased progressively. In the cow dung treatment option, the nitrate concentration decreased from 35.44 mg/kg to 14.28 mg/kg. Phosphate concentration of cow dung option decreased from 25.41 mg/kg to 9.31mg/kg. The control had the nitrate decreased from 8.42 mg/kg to 6.98 mg/kg. Percentage total organic carbon (% TOC in the cow dung option decreased from 4.06% to 0.96%. Control experiment had the % TOC decreased from 3.32% to 2.99%. Studies using Gas chromatographic analyses showed that 0%, 49.88%, and 69.85% of Total petroleum hydrocarbon (TPH were lost at zero hour, 28th day and 70th day respectively in the cow dung option. In addition, in the control experimental set-up, 0%, 7.14% and 13.42% of TPH were lost at zero hour, 28th day and 70th day respectively.Conclusion, significance and impact of study: The use of organic nutrient sources such as cow dung has shown good promises in bioremediation of crude oil impacted Mangrove Swamps in the Niger Delta. The next line of action is to transfer the technology to pilot scale study.

Biopiles for remediation of petroleum-contaminated soils: a Polish case study

International Nuclear Information System (INIS)

Hazen, T. C.; Tien, A. J.; Worsztynowicz, A.; Altman, D. J.; Ulfig, K.; Manko, T.

2002-01-01

The US Department of Energy and the Institute for Ecology of Industrial Areas of Poland demonstrated bioremediation techniques for the clean up of acidic petroleum sludge impacted soils at an oil refinery in southern Poland. The waste was composed of high molecular weight paraffinic and polynuclear aromatic hydrocarbons. Benzo(a)pyrene and BTEX compounds were identified as the contaminants of concern. Approximately 3,300 m 3 of contaminated soil (TPH ∼ 30,000 ppm) was targeted for treatment. A biopile design which employed a combination of passive and active aeration in conjunction with nutrient and surfactant application was used to increase the biodegradation of the contaminants of concern. Over the 20 month project, more than 81% (120 metric tons) of petroleum hydrocarbons were biodegraded. Despite the fact the material treated was highly weathered and very acidic, biodegradation rates of 121 mg/kg soil/day in the actively aerated side (82 mg/kg soil/day in the passive side) were achieved in this biopile. Microbial counts and dehydrogenase measurements gave the best correlation with the biodegradation rates. Costs were competitive or significantly lower when compared with other ex situ treatment processes. (author)

Distribution and origin of hydrocarbons in water and sediment in Sao Sebastiao, SP, Brazil

International Nuclear Information System (INIS)

Zanardi, Eliete; Bicego, Marcia Caruso; Miranda, Luiz Bruner de; Weber, Rolf Roland

1999-01-01

This study describes the dissolved/dispersed petroleum hydrocarbons (DDPH) in surface water and the origin and distribution of aliphatic and aromatic hydrocarbons in samples from the surface bottom sediments. The main objective was to verify the anthropogenic contribution on the adjacent inner shelf of Sao Sebastiao, taking into account the distribution of hydrographic properties and knowledge of the main circulation. The DDPH concentration range of the 20 samples were from 0.35 to 2.50 m u g . L -1 , characterising this region as slightly affected by the contribution of petroleum hydrocarbons. Considering sediment hydrocarbon results, sites located in the inner shelf were divided into three groups: one with mainly biogenic hydrocarbons, a second one with biogenic and petroleum hydrocarbons and a third with significant contribution of petroleum hydrocarbons. These results show an influence of human activities in the Sao Sebastiao Channel on the surrounding areas of the inner shelf. (Author)

SOLID FUEL OF HYDROCARBON, WOOD AND AGRICULTURAL WASTE FOR LOCAL HEAT SUPPLY SYSTEMS

Directory of Open Access Journals (Sweden)

B. M. Khroustalev

2017-01-01

Full Text Available In Belarus oil refining and oil producing industries are paid close attention. On the background of the active maintaining the level of oil processing and volume of oil extraction in our country and in the countries of the Eurasian Economic Union there is a steady formation of hydrocarbon-containing waste; therefore recycling of the latter is an urgent task to improve the competitiveness of production. The most cost-effective way of using hydrocarbon waste is the conversion of it into power resources. In this case it is possible to obtain significant power-saving and economic effect of the combined use of a hydrocarbon, wood, agricultural and other combustible waste, meanwhile improving the ecological situation at the sites of waste storage and creating a solid fuel with the necessary energy and specified physical-and-chemical properties. A comprehensive solution of a recycling problem makes it possible to use as energy resources a lot of waste that has not found application in other technologies, to produce alternative multi-component fuel which structure meets environmental and energy requirement for local heating systems. In addition, the implementation of such technology will make it possible to reduce power consumption of enterprises of various kinds that consume fuel and will also increase the share of local fuels in the energy balance of a particular region.

Source identification of hydrocarbons following environmental releases

Energy Technology Data Exchange (ETDEWEB)

Birkholz, D.A. [ALS Environmental, Edmonton, AB (Canada)

2010-07-01

Methods of identifying the sources of hydrocarbon contaminations were discussed in this PowerPoint presentation. Laboratories analyze for total petroleum hydrocarbons (TPH) by obtaining chromatograms of observed products. However, many petroleum products provide similar chromatograms. Several independent lines of evidence are needed for the purposes of accurate determination in legal applications. A case study of a lube oil plant spill was used to demonstrate the inconclusiveness of chromatograms and the need to determine petroleum biomarkers. Terpane, sterane, triaromatic sterane, isoprenoid, and alkylcyclohexane analyses were conducted to differentiate between the hydrocarbon samples. The analysis methods are being used with various soil, water, and crab species samples from the BP oil spill. Oil found at the different sites must be directly related to the spill. However, there are 3858 oil and gas platforms currently operating in the Gulf of Mexico. Ratios of biomarkers and polycyclic aromatic hydrocarbons (PAHs) are being developed to generate weight of evidence. A critical difference analysis was also presented. tabs., figs.

Assessment of soil pollution based on total petroleum hydrocarbons and individual oil substances.

Science.gov (United States)

Pinedo, J; Ibáñez, R; Lijzen, J P A; Irabien, Á

2013-11-30

Different oil products like gasoline, diesel or heavy oils can cause soil contamination. The assessment of soils exposed to oil products can be conducted through the comparison between a measured concentration and an intervention value (IV). Several national policies include the IV based on the so called total petroleum hydrocarbons (TPH) measure. However, the TPH assessment does not indicate the individual substances that may produce contamination. The soil quality assessment can be improved by including common hazardous compounds as polycyclic aromatic hydrocarbons (PAHs) and aromatic volatile hydrocarbons like benzene, toluene, ethylbenzene and xylenes (BTEX). This study, focused on 62 samples collected from different sites throughout The Netherlands, evaluates TPH, PAH and BTEX concentrations in soils. Several indices of pollution are defined for the assessment of individual variables (TPH, PAH, B, T, E, and X) and multivariables (MV, BTEX), allowing us to group the pollutants and simplify the methodology. TPH and PAH concentrations above the IV are mainly found in medium and heavy oil products such as diesel and heavy oil. On the other hand, unacceptable BTEX concentrations are reached in soils contaminated with gasoline and kerosene. The TPH assessment suggests the need for further action to include lighter products. The application of multivariable indices allows us to include these products in the soil quality assessment without changing the IV for TPH. This work provides useful information about the soil quality assessment methodology of oil products in soils, focussing the analysis into the substances that mainly cause the risk. Copyright © 2013 Elsevier Ltd. All rights reserved.

Influence of dispersants on trophic transfer of petroleum hydrocarbons in a marine food chain

International Nuclear Information System (INIS)

Wolfe, M. F.; Schwartz, G. J. B.; Singaram, S.; Tjeerdema, R. S.

1997-01-01

Experiments were conducted to determine the impact of dispersing agents on petroleum hydrocarbons (PH) bioavailability and trophic transfer in primary levels of a marine food chain. Uptake, bioaccumulation and metabolic transformation of a model PH, ( 1 4C)naphthalene, were measured and compared with Prudhoe Bay Crude Oil (PBCO) dispersed with Corexit 9527, and undispersed preparations of PBCO. The model food chain consisted of a primary algae producer and a primary rotifer consumer. Results showed that uptake of naphthalene increased significantly in the presence of a dispersant in algae. A significant increase in uptake was also recorded in rotifers via trophic transfer. Trophic transfer played a significant, sometimes even dominant, role in uptake and bioaccumulation. 27 refs., 6 figs

Clonal variation in survival and growth of hybrid poplar and willow in an in situ trial on soils heavily contaminated with petroleum hydrocarbons

Science.gov (United States)

Ronald S., Jr. Zalesny; Edmund O. Bauer; Richard B. Hall; Jill A. Zalesny; Joshua Kunzman; Chris J. Rog; Don E. Riemenschneider

2005-01-01

Species and hybrids between species belonging to the genera Populus (poplar) and Salix (willow) have been used successfully for phytoremediation of contaminated soils. Our objectives were to: 1) evaluate the potential for establishing genotypes of poplar and willow on soils heavily contaminated with petroleum hydrocarbons and 2)...

Poland petroleum refinery sludge lagoon demonstration project

International Nuclear Information System (INIS)

Altman, D.J.

2000-01-01

The US Department of Energy and the Institute for Ecology of Industrial Area have been working together to develop mutually beneficial, cost-effective environmental remediation technologies such as the demonstration of bioremediation techniques for the clean up of acidic petroleum sludge impacted soils at an oil refinery in southern Poland. After an expedited site characterization, treatability study, and a risk assessment study, a remediation strategy was devised. The waste material was composed primarily of high molecular weight paraffinic and polynuclear aromatic hydrocarbons. A biopile design which employed a combination of passive and active aeration in conjunction with nutrient and surfactant application as used to increase the biodegradation of the contaminants of concern

Total petroleum hydrocarbon in the tissues of some commercially important fishes of the Bay of Bengal.

Science.gov (United States)

Ansari, Zakir A; Desilva, Classy; Badesab, Shahin

2012-11-01

The present study reports the level of total petroleum hydrocarbon (TPH) in 27 commercially important fish, crustaceans and cephalopods from Orissa coast, Bay of Bengal to provide the baseline data for oil contamination in marine biota. The results showed significant differences in the TPH concentration in different species. Of all fish, Carangoides malabaricus showed the maximum TPH level (av. 13.70 μg g(-1)). In cephalopods, Loligo recorded the maximum TPH (av. 14.87 μg g(-1)) while Metapenaeus dobsoni recorded the maximum TPH (av. 13.18 μg g(-1)) among crustaceans. The concentration of TPH recorded in the present study were higher than the reported values from other studies in Bay of Bengal but were comparable with those of other Indian coast and Gulf water. The species recording maximum concentration and giving significant correlation coefficient may be of interest in oil pollution monitoring and can be used as indicator of hydrocarbon pollution in the region. Copyright © 2012 Elsevier Ltd. All rights reserved.

Molecular identification and potential of an isolate of white rot fungi in bioremediation of petroleum contaminated soils

Directory of Open Access Journals (Sweden)

Maryam Mohammadi-sichani

2017-06-01

Full Text Available Introduction:Elimination or reduction of petroleum hydrocarbons from natural resources such as water and soil is a serious problem of countries, particularly oil-rich countries of the world. Using white rotting fungi compost for bioremediation of soils contaminated by petroleum hydrocarbons is effective. The aim of this study is molecular identification and potential of anisolate of white rot fungi in bioremediation of petroleum contaminated soils. Materials and methods: Spent compost of white rotting fungi was inoculated with petroleum contaminated soil into 3%, 5% and 10% (w/w. Treatments were incubated at 25-23 °C for 3 months. Reduction of petroleum hydrocarbons in treated soil was determined by gas chromatography. Ecotoxicity of soil was evaluated by seed germination test. Results: Based on the genome sequence of 18s rRNA, it is revealed that this isolate is Ganoderma lucidum and this isolate is deposited as accession KX525204 in the Gene Bank database. Reduction of petroleum hydrocarbons in soil treated with compost (3, 5 and 10% ranged from 42% to 71%. The germination index (% in ecotoxicity tests ranged from 20.8% to 70.8%. Gas chromatography results also showed a decrease in soil Hydrocarbons compounds. Discussion and conclusion: The compost of Ganoderma lucidum, a white rot fungus, has a potential ability to remove petroleum hydrocarbons in contaminated soil. Removal of hydrocarbons was increased with increase in compost mixed with contaminated soil. Petroleum contaminated soil amended with spent compost of G.lucidum 10% during three months is appropriate to remove this pollutant.

Distribution and origin of hydrocarbons in water and sediment in Sao Sebastiao, SP, Brazil

Energy Technology Data Exchange (ETDEWEB)

Zanardi, Eliete [Universidade de Sao Paulo, Instituto Oceanografico, Sao Paulo, SP (Brazil); Bicego, Marcia Caruso; Miranda, Luiz Bruner de; Weber, Rolf Roland [Miami Univ., RSMAS/NAC, Miami, FL (United States)

1999-04-01

This study describes the dissolved/dispersed petroleum hydrocarbons (DDPH) in surface water and the origin and distribution of aliphatic and aromatic hydrocarbons in samples from the surface bottom sediments. The main objective was to verify the anthropogenic contribution on the adjacent inner shelf of Sao Sebastiao, taking into account the distribution of hydrographic properties and knowledge of the main circulation. The DDPH concentration range of the 20 samples were from 0.35 to 2.50 {sup m}u{sup g}. L{sup -1}, characterising this region as slightly affected by the contribution of petroleum hydrocarbons. Considering sediment hydrocarbon results, sites located in the inner shelf were divided into three groups: one with mainly biogenic hydrocarbons, a second one with biogenic and petroleum hydrocarbons and a third with significant contribution of petroleum hydrocarbons. These results show an influence of human activities in the Sao Sebastiao Channel on the surrounding areas of the inner shelf. (Author)

Remedial design for petroleum hydrocarbons: Soil vapor extraction, product skimmers, and air stripping

International Nuclear Information System (INIS)

Anastasi, F.S.; Loftin, H.J.

1994-01-01

Site characterization activities at an Army installation in Virginia performed prior to closure identified a significant release of gasoline from underground storage tanks and piping associated with the post exchange service station. Floating liquid-phase petroleum hydrocarbons (FLPH) observed in the subsurface over an area of approximately 80,000 square feet ranged up to 5 feet in thickness. Ground water was found to be contaminated with dissolved components of gasoline over an area of approximately 150,000 square feet. A nearby lake and adjacent streams were not impacted by either free-phase or dissolved contamination. Interim remedial measures, including pilot testing of FLPH, vapor-phase, and ground water recovery technologies, were implemented following discovery of the release. Over 5,000 gallons of free-phase product were recovered by skimming and approximately 1,450 gallons of product equivalent were recovered during pilot testing of a soil vapor extraction (SVE) system. At the conclusion of these actions, hydrocarbons remain distributed in the subsurface in the adsorbed-, dissolved-, and vapor-phase. The majority of residual on-site contamination is believed to be either adsorbed to soil particles or as FLPH. The final design of an integrated remediation system based on the pilot test results addressed these conditions

Petroleum Hydrocarbon in Surface Sediment from Coastal Area of Putatan and Papar, Sabah

International Nuclear Information System (INIS)

Siti Aishah Mohd Ali; Rohana Tair; Yang, S.Z.; Masni Mohd Ali

2013-01-01

Total petroleum hydrocarbons (TPH) and percent total organic carbon (TOC) were investigated in surface sediments from coastal area of Papar and Putatan, Sabah. Samples were collected in five different stations in each area by using Ponar grab sampler. Samples were extracted with Soxhlet, concentrated and analyzed by using UV/ VIS spectrophotometer. The overall mean and range of TPH concentrations in the sediments from coastal area of Papar and Putatan were 1.95 (0.53-4.59 mg/ kg dw Miri crude oil equivalents) and 0.85 (0.26-1.64 mg/ kg dw Miri crude oil equivalents) respectively. Meanwhile, the TOC ranged from 0.81-2.32 % and 0.35-0.81 % respectively. Statistical analysis using Pearson correlation showed no significant differences between TPH and TOC (p<0.05) in both areas. (author)

Direct soil contact values for ecological receptors exposed to weathered petroleum hydrocarbon (PHC) fraction 2.

Science.gov (United States)

Angell, Robin A; Kullman, Steve; Shrive, Emma; Stephenson, Gladys L; Tindal, Miles

2012-11-01

Ecological tier 1 Canada-wide standards (CWS) for petroleum hydrocarbon (PHC) fraction 2 (F2; >nC10-C16) in soil were derived using ecotoxicological assessment endpoints (effective concentrations [ECs]/lethal concentrations [LCs]/inhibitory concentrations, 25% [IC25s]) with freshly spiked (fresh) fine- and coarse-grained soils. These soil standards might be needlessly conservative when applied to field samples with weathered hydrocarbons. The purpose of the present study was to assess the degradation and toxicity of weathered PHC F2 in a fine-grained soil and to derive direct soil contact values for ecological receptors. Fine-grained reference soils were spiked with distilled F2 and weathered for 183 d. Toxicity tests using plants and invertebrates were conducted with the weathered F2-spiked soils. Endpoint EC/IC25s were calculated and used to derive soil standards for weathered F2 in fine-grained soil protective of ecological receptors exposed via direct soil contact. The values derived for weathered F2 were less restrictive than current ecological tier 1 CWS for F2 in soil. Copyright © 2012 SETAC.

Wet Oxidation of Fine Soil Contaminated with Petroleum Hydrocarbons: A Way towards a Remediation Cycle

Directory of Open Access Journals (Sweden)

Maria Cristina Collivignarelli

2018-06-01

Full Text Available The aim of this experimental study was to assess the feasibility of using a wet oxidation (WO process for treating fine soil with a high level of total petroleum hydrocarbons (TPHs. Two samples of soil were spiked with two different contaminants (motor oil, and motor oil + diesel. The samples were subjected to a WO bench plant test, where the effect of the main process parameters (i.e., temperature and reaction time on the removal of TPHs was investigated. Results show that the WO process is effective for the decontamination of hydrocarbons, and a strong reduction (>85% can be obtained with the typical working conditions of a full-scale plant (temperature = 250 °C, reaction time = 30 min. The solid residue resulting from the WO process was characterized in order to evaluate the recovery options. In terms of chemical characterization, the contents of the pollutants comply with the Italian regulations for commercial and industrial site use. Moreover, the results of the leaching test suggested that these residues could be reused for ceramic and brick manufacturing processes.

Caspian sea: petroleum challenges

International Nuclear Information System (INIS)

2005-01-01

The Caspian sea is one of the world areas the most promising in terms of investments and petroleum development. This study presents the petroleum challenges generated by this hydrocarbons reserve. The first part discusses the juridical status (sea or lake), the petroleum and the gas reserves, the ecosystem and the today environment (fishing and caviar), the geostrategic situation and the transport of gas and oil. It provides also a chronology from 1729 to 2005, a selection of Internet sites, books and reports on the subject and identity sheets of the countries around the Caspian sea. (A.L.B.)

Lasers and petroleum in Venezuela

Energy Technology Data Exchange (ETDEWEB)

da Costa, G.; Guerri, G.; Calatroni, J. (Universidad Simon Bolivar, Caracas (Venezuela). Lab. de Optica Cuantica)

1978-06-01

The viscosity of heavy hydrocarbons is one reason why conventional drilling methods are insufficient for petroleum extraction in Venezuela at a depth of 1000 m. The Quantum Optics Laboratory of Simon Bolivar University in Caracas is conducting a search for novel perforation and heating tools for petroleum extraction. Basic research is being carried out using a 10 MW TEA-CO/sub 2/ laser. The laser is not only a research tool but a matter of national interests, as petroleum is Venezuela's main export article.

Gasoline from Kumkol deposit petroleum

International Nuclear Information System (INIS)

Nadirov, A.N.; Zhizhin, N.I.; Musaeva, Z.G.

1997-01-01

Samples of gasoline from petroleum of Kumkol deposit are investigated by chromatographic analysis. It is found, that gasoline is characterizing by increased content of iso-paraffin hydrocarbons. (author)

The petroleum industry in 2003; L'industrie petroliere en 2003

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

Biotreatment of hydrocarbons from petroleum tank bottom sludges in soil slurries

International Nuclear Information System (INIS)

Ferrari, M.D.; Neirotti, E.; Albornoz, C.; Mostazo, M.R.; Cozzo, M.

1996-01-01

Biotreatment of oil wastes in aqueous slurries prepared with sandy loam soil and inoculated with selected soil cultures was evaluated. After 90 days, oil removal was 47%. Removal of each hydrocarbon class was 84% for saturates, 20% for aromatics, and 44% for asphaltenes. Resins increased by 68%. The use of a soil with a lower level of fine particles or minor organic matter content, or reinoculation with fresh culture did not improve oil elimination. Residual oil recovered from slurries was biotreated. Oil removal was 22%. Slurry-phase biotreatment showed less variability and faster oil removal than solid-phase biotreatment. (author)

Solid wastes management in petroleum refineries; Gerenciamento de residuos solidos em refinarias de petroleo

Energy Technology Data Exchange (ETDEWEB)

Araujo, Lizabela Souza de [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica]|[Agencia Nacional de Petroleo, Brasilia, DF (Brazil)]. E-mail: lizabela@eq.ufrj.br; Nicolaiewsky, Elioni [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica. Dept. de Engenharia Quimica]. E-mail: elioni@eq.ufrj.br; Freire, Denize Dias de Carvalho [Universidade Federal, Rio de Janeiro, RJ (Brazil). Escola de Quimica. Dept. de Engenharia Bioquimica]. E-mail: denize@eq.ufrj.br

2002-07-01

This work performs a survey on the solid wastes generated from petroleum refining activities. The possible environmental impacts are analysed and procedures for disposal and treatment are suggested. The treatment techniques are detached: minimization, incineration, co-processing, bioremediation and industrial embankments.

Status of the petroleum pollution in the Wider Caribbean Sea

Energy Technology Data Exchange (ETDEWEB)

Botello, Alfonso V; Villanueva F, Susana [Universidad Nacional Autonoma de Mexico, Mexico City (Mexico). Inst. de Ciencias del Mar y Limnologia

1996-07-01

In 1976, the IOC-UNESCO and UNEP convened a meeting in Port of Spain to analyze the marine pollution problems in the region and noted that petroleum pollution was of region-wide concern and recommended to initiate a research and monitoring program to determine the severity of the problem and monitor its effects. Actually, the Wider Caribbean is potentially one of the largest oil producing areas in the world. Major production sites include Louisiana and Texas; USA; the Bay of Campeche, Mexico; Lake Maracaibo, Venezuela; and the Gulf of Paria, Trinidad; all which are classified as production accident high-risk zones. Main sources of petroleum pollution in the Wider Caribbean are: production, exploitation, transportation, urban and municipal discharges, refining and chemical wastes, normal loading operations and accidental spills. About 5 million of barrels are transported daily in the Caribbean, thus generating an intense tanker traffic. It has been estimated that oil discharges from tank washings within the Wider Caribbean could be as high as 7 millions barrels/year. The results of the CARIPOL Regional Programme conducted between 1980-1987 pointed out that a significant levels of petroleum pollution exists throughout the Wider Caribbean and include serious tar contamination of windward exposed beaches, high levels of floating tar within the major currents system and very high levels of dissolved/dispersed hydrocarbons in surface waters. Major effects of this petroleum pollution include: high tar level on many beaches that either prevent recreational use or require very expensive clean-up operations, distress and death to marine life and responses in the enzyme systems of marine organisms that have been correlated with declines in reproductive success. Finally the presence of polycyclic aromatic hydrocarbons in tissues of important economic species have been reported with its potential carcinogenic effects. (author)

Status of the petroleum pollution in the Wider Caribbean Sea

International Nuclear Information System (INIS)

Botello, Alfonso V.; Villanueva F, Susana

1996-01-01

In 1976, the IOC-UNESCO and UNEP convened a meeting in Port of Spain to analyze the marine pollution problems in the region and noted that petroleum pollution was of region-wide concern and recommended to initiate a research and monitoring program to determine the severity of the problem and monitor its effects. Actually, the Wider Caribbean is potentially one of the largest oil producing areas in the world. Major production sites include Louisiana and Texas; USA; the Bay of Campeche, Mexico; Lake Maracaibo, Venezuela; and the Gulf of Paria, Trinidad; all which are classified as production accident high-risk zones. Main sources of petroleum pollution in the Wider Caribbean are: production, exploitation, transportation, urban and municipal discharges, refining and chemical wastes, normal loading operations and accidental spills. About 5 million of barrels are transported daily in the Caribbean, thus generating an intense tanker traffic. It has been estimated that oil discharges from tank washings within the Wider Caribbean could be as high as 7 millions barrels/year. The results of the CARIPOL Regional Programme conducted between 1980-1987 pointed out that a significant levels of petroleum pollution exists throughout the Wider Caribbean and include serious tar contamination of windward exposed beaches, high levels of floating tar within the major currents system and very high levels of dissolved/dispersed hydrocarbons in surface waters. Major effects of this petroleum pollution include: high tar level on many beaches that either prevent recreational use or require very expensive clean-up operations, distress and death to marine life and responses in the enzyme systems of marine organisms that have been correlated with declines in reproductive success. Finally the presence of polycyclic aromatic hydrocarbons in tissues of important economic species have been reported with its potential carcinogenic effects. (author)

Treatment of Petroleum Drill Cuttings Using Stabilization/Solidification Method by Cement and Modified Clay Mixes

Directory of Open Access Journals (Sweden)

Soroush Ghasemi

2017-04-01

Full Text Available High organic content in petroleum drill cuttings is a substantial obstacle which hinders cement hydration and subsequently decreases the clean-up efficiency of the stabilization/solidification (S/S process. In this study, a modified clayey soil (montmorillonite with low to moderate polarity was used as an additive to cement. Because of its high adsorption capacity, the clay is capable of mitigating the destructive role of organic materials and preventing their interference with the hydration process. Mixes containing different ratios of cement, waste and modified clay were prepared and tested for their mechanical and chemical characteristics. Total petroleum hydrocarbons (TPH and Pb content of the samples were analyzed as well. For this purpose, the mixes were subjected to unconfined compressive strength (UCS and toxicity characteristic leaching procedure (TCLP tests. The results indicated that the specimens with 28-day curing time at a cement/waste ratio of 25% or higher (w/w and 10% modified clay (w/w met the Environmental Protection Agency (EPA criterion for compressive strength. Moreover, a reduction of 94% in the leaching of TPH was observed with the specimens undergoing the TCLP with a cement/waste ratio of 30% (w/w and a clay/waste ratio of 30% (w/w. Finally, the specimens with 30% cement/waste and 10% clay/waste ratios showed the least concentration (6.14% of leached Pb.

Reduction of polycyclic aromatic hydrocarbons (PAHs) from petroleum-contaminated soil using thermal desorption technology

International Nuclear Information System (INIS)

Silkebakken, D.M.; Davis, H.A.; Ghosh, S.B.; Beardsley, G.P.

1995-01-01

The remediation of petroleum-contaminated soil typically requires the selection of a treatment option that addresses the removal of both volatile and semi-volatile organic compounds. Volatile organic compounds (VOCs), primarily BTEX (benzene, toluene, ethylbenzene, and xylenes) compounds, can be readily removed from the soil by a variety of well-established technologies. The semivolatile organic compounds, especially the polycyclic aromatic hydrocarbons (PAHS) that are characteristic of petroleum-contaminated soil, are not as amenable to conventional treatment. Low temperature thermal volatilization (LTTV) can be a viable treatment technology depending on the initial contaminant concentrations present and applicable cleanup objectives that must be attained. A-two-phase treatability study was conducted at 14 former underground storage tank (UST) sites to evaluate the applicability and effectiveness of LTTV for remediation of approximately 31,000 tons of PAH-contaminated soil. The PAHs of primary concern included benzo(a)anthracene, chrysene, benzo(a)pyrene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(g,h,i)perylene, dibenz(a,h) anthracene, and indeno(1,2,3-cd)pyrene. During Phase 1, LTTV operational parameters were varied by trial-and-error and changes in soil treatment effectiveness were monitored. Phase B of the treatability study incorporated the appropriate treatment regime established during Phase 1 to efficiently remediate the remaining contaminated soil

Thermal treatment of petroleum contaminated soils - A case study

International Nuclear Information System (INIS)

Bubier, T.W.; Bilello. C.M.

1993-01-01

Thermal treatment is a cost-effective treatment method for removing chemicals from contaminated soils. However, detailed applicability studies are lacking. The goals of this paper are to (1) present the results of a thermal treatment study and (2) discuss the specific elements which must be evaluated prior to determining whether thermal treatment is a feasible option for a remediation project. Results of data collected during a pilot study involving thermal treatment of petroleum contaminated soils at a Marine Terminal are presented. The pilot study consisted of thermally treating the C8 through C40 + (gasoline, kerosene, diesel, motor oil, bunker fuel, etc.) hydrocarbon contaminated soils at treatment temperatures ranging from 250 degrees Fahrenheit (degree F) up to 550 degrees F. The low-temperature thermal treatment unit consisted of a rotary kiln with a temperature capacity of approximately 600 degrees F, a baghouse, and a catalytic oxidizer. The soil was monitored for concentrations of petroleum hydrocarbons and volatile organic compounds before and after treatment. The results of the pilot study were used to determine if thermal treatment technology is a cost-efficient and effective option of remediating the estimated 300,000 tons of petroleum contaminated soil to acceptable cleanup levels. The low-temperature thermal treatment pilot study was effective in desorbing the short chain hydrocarbons (gasoline and diesel) but was not effective in desorbing the long-chain petroleum hydrocarbons, such as motor oils and bunker fuels, from the soil. This was primarily due to the boiling points of motor oil and bunker fuels which were higher than the temperature capacity of the pilot study treatment equipment. Additional factors that influenced the effectiveness of the desorption process included configuration of the treatment equipment, soil moisture content, soil particle size, and type and concentration of petroleum hydrocarbons

27 CFR 21.125 - Rubber hydrocarbon solvent.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative. (b...

Mutagenicity and chemical characterization of two petroleum distillates.

Science.gov (United States)

Carver, J H; MacGregor, J A; King, R W

1984-08-01

To investigate if the Salmonella/microsome assay could reliably screen complex petroleum samples for their carcinogenic potential, two high boiling (700-1070 degrees F) petroleum distillates with known activity in a dermal carcinogenesis bioassay were fully characterized with respect to their hydrocarbon composition and polynuclear aromatic hydrocarbon (PNA) content and assayed for mutagenic activity. Mutagenicity assays were also carried out on the aromatic hydrocarbon aggregates separated from these oils by adsorption chromatography. The composition of the distillates differed substantially, and reflected the fact that they were derived from crude oils that were extremely divergent in hydrocarbon character. Both the distillate and aromatic samples consistently induced a very slight increase in revertant TA98 and TA100 colonies; however, an increase of 2-4-fold over background was observed when the S-9 concentration was increased 5-10 times that of the standard assay. The maximal response was less than that expected from the samples' known PNA content and observed potency in the dermal carcinogenesis bioassay. In the Salmonella/microsome assay, all samples inhibited the mutagenic activity of added benzo[a]pyrene. Discordance between the magnitude of the samples' mutagenic activity and their known PNA content may be related to direct or indirect inhibition of sample PNAs by other components of the complex petroleum fractions. Observed inhibitory effects support the use of elevated S-9 concentration in the in vitro assays assessing the carcinogenic potential of petroleum-derived materials.

TECHNOLOGY FOR EFFICIENT USAGE OF HYDROCARBON-CONTAINING WASTE IN PRODUCTION OF MULTI-COMPONENT SOLID FUEL

Directory of Open Access Journals (Sweden)

B. M. Khroustalev

2016-01-01

Full Text Available The paper considers modern approaches to usage of hydrocarbon-containing waste as energy resources and presents description of investigations, statistic materials, analysis results on formation of hydrocarbon-containing waste in the Republic of Belarus. Main problems pertaining to usage of waste as a fuel and technologies for their application have been given in the paper. The paper describes main results of the investigations and a method for efficient application of viscous hydrocarbon-containing waste as an energy-packed component and a binding material while producing a solid fuel. A technological scheme, a prototype industrial unit which are necessary to realize a method for obtaining multi-component solid fuel are represented in the paper. A paper also provides a model of technological process with efficient sequence of technological operations and parameters of optimum component composition. Main factors exerting significant structure-formation influence in creation of structural composition of multi-component solid fuel have been presented in the paper. The paper gives a graphical representation of the principle for selection of mixture particles of various coarseness to form a solid fuel while using a briquetting method and comprising viscous hydrocarbon-containing waste. A dependence of dimensionless concentration g of emissions into atmosphere during burning of two-component solid fuel has been described in the paper. The paper analyzes an influence of the developed methodology for emission calculation of multi-component solid fuels and reveals a possibility to optimize the component composition in accordance with ecological function and individual peculiar features of fuel-burning equipment. Special features concerning storage and transportation, advantages and disadvantages, comparative characteristics, practical applicability of the developed multi-component solid fuel have been considered and presented in the paper. The paper

In Situ Hydrocarbon Degradation by Indigenous Nearshore Bacterial Populations

International Nuclear Information System (INIS)

Cherrier, J.

2005-01-01

Potential episodic hydrocarbon inputs associated with oil mining and transportation together with chronic introduction of hydrocarbons via urban runoff into the relatively pristine coastal Florida waters poses a significant threat to Florida's fragile marine environment. It is therefore important to understand the extent to which indigenous bacterial populations are able to degrade hydrocarbon compounds and also determine factors that could potentially control and promote the rate at which these compounds are broken down in situ. Previous controlled laboratory experiments carried out by our research group demonstrated that separately both photo-oxidation and cometabolism stimulate bacterial hydrocarbon degradation by natural bacterial assemblages collected from a chronically petroleum contaminated site in Bayboro Bay, Florida. Additionally, we also demonstrated that stable carbon and radiocarbon abundances of respired CO 2 could be used to trace in situ hydrocarbon degradation by indigenous bacterial populations at this same site. This current proposal had two main objectives: (a) to evaluate the cumulative impact of cometabolism and photo-oxidation on hydrocarbon degradation by natural bacterial assemblages collected the same site in Bayboro Bay, Florida and (b) to determine if in situ hydrocarbon degradation by indigenous bacterial populations this site could be traced using natural radiocarbon and stable carbon abundances of assimilated bacterial carbon. Funds were used for 2 years of full support for one ESI Ph.D. student, April Croxton. To address our first objective a series of closed system bacterial incubations were carried out using photo-oxidized petroleum and pinfish (i.e. cometabolite). Bacterial production of CO 2 was used as the indicator of hydrocarbon degradation and (delta) 13 C analysis of the resultant CO 2 was used to evaluate the source of the respired CO 2 (i.e. petroleum hydrocarbons or the pinfish cometabolite). Results from these time

Production, characterization and fuel properties of alternative diesel fuel from pyrolysis of waste plastic grocery bags

Science.gov (United States)

Pyrolysis of HDPE waste grocery bags followed by distillation resulted in a liquid hydrocarbon mixture that consisted of saturated aliphatic paraffins (96.8%), aliphatic olefins (2.6%), and aromatics (0.6%) that corresponded to the boiling range of conventional petroleum diesel fuel (#1 diesel 182–2...

The petroleum industry in 2002; L'industrie petroliere en 2002

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

This document presents the petroleum industry situation in 2002 on the following topics: the evolution of the crude oil prices, the world petroleum exploration and production, the french petroleum exploration and production, the para-petroleum industry, the supplies in hydrocarbons, the refining, the evolution of the products quality and the substitution fuels, the internal transportation of petroleum products, the petroleum products storage and the crisis management, the petroleum products consumption, the taxation of the petroleum products, the prices of the petroleum products, the distribution of the petroleum products. (A.L.B.)

Hydrocarbon degradation potential in reference soils and soils contaminated with jet fuel

International Nuclear Information System (INIS)

Lee, R.F.; Hoeppel, R.

1991-01-01

Petroleum degradation in surface and subsurface soils is affected by such factors as moisture content, pH, soil type, soil organics, temperature, and oxygen concentrations. In this paper, the authors determine the degradation rates of 14 C-labeled hydrocarbons added to soils collected from a contaminated surface site, contaminated subsurface sites, and a clean reference site. The radiolabeled hydrocarbons used include benzene, toluene, naphthalene, 1-methynaphthalene, phenanthrene, fluorene, anthracene, chrysene, and hexadecane. Microbial degradation rates were based on determination of mineralization rates (production of 14 CO 2 ) of hydrocarbons that were added to soil samples. Since water was added and oxygen was not limiting, the hydrocarbon rates determined are likely to be higher than those occurring in situ. Using radiolabeled hydrocarbons, information can be provided on differences in the degradation rates of various petroleum compounds in different types of soils at a site, on possible production of petroleum metabolites in the soil, and on the importance of anaerobic petroleum degradation and the effects of nutrient, water, and surfactant addition on biodegradation rates

The petroleum industry in 2005; L'industrie petroliere en 2005

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

This document provides information on the petroleum industry for the year 2005. It discusses the world gas and petroleum markets, the world and french petroleum exploration and production, the petroleum and byproducts industry in France, the hydrocarbons supplying, the refining in France, the evolution of the products and fuels substitution quality, the internal transports of petroleum products, the storage consumption and taxes of petroleum products, the prices and distribution of the petroleum products. (A.L.B.)

Contamination by heavy metals and petroleum hydrocarbons: a threat to mangroves

Directory of Open Access Journals (Sweden)

Thaís dos Santos Alencar

2016-12-01

Full Text Available The mangrove ecosystem is one of the most productive ecosystems on the planet with relevant ecological importance. It offers several services such as protection of the coastal region, immobilization of contaminants, as it is a food source and refuge for various organisms. However, mangroves are threatened by human activities. Oil spills in areas close to mangroves, for example, are potential sources for the entry of contaminants such as heavy metals and hydrocarbons. Among other sources of threat, we list industrial waste and sewage, mining and fertilizer use. When they reach the mangroves, these contaminants may cause several negative effects and affect its balance.

Bacterial community shift and hydrocarbon transformation during bioremediation of short-term petroleum-contaminated soil.

Science.gov (United States)

Wu, Manli; Ye, Xiqiong; Chen, Kaili; Li, Wei; Yuan, Jing; Jiang, Xin

2017-04-01

A laboratory study was conducted to evaluate the impact of bioaugmentation plus biostimulation (BR, added both nutrients and bacterial consortia), and natural attenuation (NA) on hydrocarbon degradation efficiency and microflora characterization during remediation of a freshly contaminated soil. After 112 days of remediation, the initial level of total petroleum hydrocarbon (TPH) (61,000 mg/kg soil) was reduced by 4.5% and 5.0% in the NA and BR treatments, respectively. Bioremediation did not significantly enhance TPH biodegradation compared to natural attenuation. The degradation of the aliphatic fraction was the most active with the degradation rate of 30.3 and 28.7 mg/kg/day by the NA and BR treatments, respectively. Soil microbial activities and counts in soil were generally greater for bioremediation than for natural attenuation. MiSeq sequencing indicated that the diversity and structure of microbial communities were affected greatly by bioremediation. In response to bioremediation treatment, Promicromonospora, Pseudomonas, Microcella, Mycobacterium, Alkanibacter, and Altererythrobacter became dominant genera in the soil. The result indicated that combining bioaugmentation with biostimulation did not improve TPH degradation, but soil microbial activities and structure of microbial communities are sensitive to bioremediation in short-term and heavily oil-contaminated soil. Copyright © 2017 Elsevier Ltd. All rights reserved.

Filamentous fungi remove weathered hydrocarbons from polluted soil of tropical Mexico

OpenAIRE

PÉREZ-ARMENDÁRIZ, Beatriz; MARTÍNEZ-CARRERA, Daniel; CALIXTO-MOSQUEDA, María; ALBA, Joel; RODRÍGUEZ-VÁZQUEZ, Refugio

2010-01-01

Weathered hydrocarbons from worldwide petrolic activities become more recalcitrant over time. The removal of petroleum hydrocarbons from a polluted soil [65,000 mg total petroleum hydrocarbons (TPH)/kg soil], which had been exposed to tropical environmental conditions for more than 20 years in southeast Mexico, was studied using filamentous fungi. Experiments were carried out in batch reactors (60 mL) containing a substrate consisting of polluted soil and sugar cane bagasse pith as bulk agent...

Seasonal effect on biomarkers of exposure to petroleum hydrocarbons in fish from Kuwait's marine area.

Science.gov (United States)

Beg, M U; Al-Subiai, S N; Al-Jandal, N; Butt, S A; Beg, K R; Al-Husaini, M

2015-11-30

The aquatic biota of the Arabian Gulf deals with exposure to chronic oil pollution, several constituents of which cause induction of Cytochrome P450 1A that serves as a biomarker of AhR ligand exposure. In this study, fluorescent aromatic compounds (FACs) in bile and 7-ethoxyresorufin-o-deethylase (EROD) catalytic activity were determined as a measure of exposure biomarkers in two fish species, yellow fin seabream (Acanthopagrus latus) and tonguesole (Cynoglossus arel) captured from Kuwait Bay and outside the Bay area. FACs in fish bile determined by using fixed-wavelength fluorescence (FF) showed high fluorescence ratios between FF290/335 and FF380/430 indicating predominant exposure to low molecular weight, naphthalene-rich petroleum products (375±91.0 pg ml(-1)). Exposures to benzo(a)pyrene-type high-molecular weight polycyclic aromatic hydrocarbons (PAHs) originating from burnt fuel were also present in appreciable concentration in the bile. The ratio of petrogenic to pyrogenic hydrocarbon was twofold higher in winter compared to summer months in both species. Seasonal effect on EROD was significant in tonguesole in Auha site (Ppollution in Kuwait Bay area. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermal and catalytic decomposition behavior of PVC mixed plastic waste with petroleum residue

Energy Technology Data Exchange (ETDEWEB)

Ali, Mohammad Farhat; Siddiqui, Mohammad Nahid [Department of Chemistry, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2005-08-15

The pyrolysis and hydropyrolysis of PVC mixed plastic waste alone and with petroleum residue was carried out at 150 and 350{sup o}C under N{sub 2} gas and at 430{sup o}C under 6.5MPa H{sub 2} gas pressure. The behavior of plastic waste during thermal and catalytic decomposition has also been studied in single- and two-stage reaction processes. In the individual pyrolysis process, both the petroleum residue and polystyrene (PS) undergo more than 90% conversion to liquid and gaseous products, whereas low-density polyethylene (LDPE) and high-density polyethylene (HDPE) yielded lower conversions products, and polypropylene (PP) and polyvinyl chloride (PVC) afforded somewhere a moderate to high conversion products. In a single-stage pyrolysis reaction, PVC was processed with petroleum residue at 150 and 430{sup o}C, under N{sub 2} gas for 1h at each temperature in a glass reactor. The model PVC and waste PVC showed slight variations in the products distribution obtained from the glass reactor. In two-stage process, model PVC, vacuum gas oil (VGO) and a number of different catalysts were used in a stainless steel autoclave micro tubular reactor at 350{sup o}C under the stream of N{sub 2} gas for 1h and at 430{sup o}C under 950psi (6.5MPa) H{sub 2} pressure for the duration of 2h. Significantly, different products distributions were obtained. Among the catalysts used, fluid catalytic cracking (FCC) and hydrocracking catalysts (HC-1) were most effective in producing liquid fuel (hexane soluble) materials. The study shows that the catalytic coprocessing of PVC with VGO is a feasible process by which PVC and VGO materials can be converted into transportation fuels.

The petroleum industry in 2001; L'industrie petroliere en 2001

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This economic analysis presents the 2001 highlights and key-data of the world petroleum industry: evolution of crude prices, exploration and production worldwide, petroleum exploration and production in France, para-petroleum industry, hydrocarbon supplies, refining activity, evolution of quality of products and fuel substitutes, domestic transports, storage, consumption, fiscality, prices and distribution of petroleum products. (J.S.)

Aspects of petroleum hydrocarbon metabolism in marine animals

Science.gov (United States)

Mironov, O. G.

1980-03-01

Studies on hydrocarbon composition of Black Sea mussels Mytilus galloprovincialis sampled from different habitats indicate that the quantity and composition of hydrocarbons distributed in the molluscs depend on season and sea-water quality. The data obtained under experimental conditions testify to the possibility of hydrocarbon concentration in mussel tissues after death. During filtration in sea water containing oil and oil products, these pollutants are bound into faeces and pseudofaeces which contain a greater percentage of aromatic compounds than the oil initially present in sea water. Quantitative data are presented on hydrocarbon changes in mussel excretory products during transfer from oil-polluted to clean sea water. When Black Sea crabs Eriphia verrucosa are fed with mussels containing fuel-oil components accumulated from sea water, the pollutants concentrate in the whole body of the crab. This is in contrast to parenteral oil uptake, which leads to a concentration of most of the hydrocarbon in the muscles.

Stimulation of biological N2-fixation to accelerate the microbial remediation of soil contaminated by petroleum hydrocarbons

International Nuclear Information System (INIS)

Tereshenko, N.N.; Lushnikov, S.V.

2005-01-01

All remediation projects are comprised at least in accelerating the processes of the self-cleaning and self-restoration of biocenose which is led to increasing the functional activity of hydrocarbon-oxidizing microflora (HOM). Some of experts are carefully relate to introducing the commercial cultures of active hydrocarbon-consuming microbes into soils. They are afraid of unpredictable behavior of the cultures in soils. That why the stimulation of metabolic activity of indigenous soil microflora seems to be most preferable. In fact, contamination of soil with low nitrogen capacity by oil spills leads to significant deficient of nitrogen for HOM. Nitrogen content limits the soil self-restoration. Inorganic nitrogen fertilizers are supplied to recover the balance. The study of the microbial destruction of petroleum-hydrocarbons in association with biochemical transformation of nitrogen was carried out in lab and field experiments during 2000-2004. Study showed the activity of HOM correlates with rate of microbial fixing atmospheric nitrogen. Activity of biological N 2 -fixation significantly depends on supplying fertilizers (dose, date and kind). General practice of remediation of hydrocarbon-contaminated soils applies high initial doses of nitrogen-fertilizers (0.5-1 t per ha). Such practice leads to inhibition of N 2 -fixation processes, decreasing rate of oil destruction and loosing nitrogen due to activation of microbial denitrification. In opposition to that, the fractioned and advanced supplying mineral nitrogen fertilizers with aluminosilicate is the cost-effective approach to remediation of hydrocarbon-contaminated soils. Field experiments showed that the approach allows to increase efficiency of treatment up to 70-75% and to decrease operational expenses 2-3 times at least. (authors)

Comparison of three field screening techniques for delineating petroleum hydrocarbon plumes in groundwater at a site in the southern Carson Desert, Nevada

International Nuclear Information System (INIS)

Smuin, D.R.

1993-01-01

Three types of field screening techniques used in the characterization of potentially contaminated sites at Naval Air Station Fallon, Nevada, are compared. The methods and results for each technique are presented. The three techniques include soil-gas surveys, electromagnetic geophysical surveys, and groundwater test hole screening. Initial screening at the first study site included two soil-gas surveys and electromagnetic geophysical studies. These screening methods identified I areas of contamination; however, results were inconclusive. Therefore groundwater test hole screening was performed. Groundwater screening consisted of auger drilling down to the shallow alluvial aquifer. Groundwater samples were collected from the open drill hole with a bailer. On-site head-space analyses for volatile organic compounds (VOCS) were performed using a portable gas chromatograph (GC). Five areas of floating petroleum hydrocarbon product were identified along with the overall dissolved contaminant plume boundaries. Well placement was re-evaluated, and well sites were relocated based on the screening information. The most effective technique for identification of petroleum hydrocarbon-contaminant plumes was groundwater test hole screening. Groundwater screening was subsequently performed at 19 other sites. A total of 450 test holes were analyzed resulting in the delineation of six plumes

Fiscal 1997 report on the results of the international research cooperation project for a feasibility survey for finding out seeds of the international joint research. Effective use technology of saturated hydrocarbon (technology against the surplus aromatic hydrocarbon/technology of high grade treatment of petroleum coke); 1997 nendo kokusai kenkyu kyoryoku jigyo (kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa). Howa tanka suiso no yuko riyo gijutsu / hokozoku tanka suiso no yojo taisaku gijutsu / sekiyu cokes no kodo shori gijutsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of the effective international research cooperation, the paper surveyed in fiscal 1997 the effective use technology of saturated hydrocarbon, technology against the surplus aromatic hydrocarbon and technology of high grade treatment of petroleum coke. In the survey of the effective use technology of saturated hydrocarbon, trends of FT synthesis technology and DME synthesis technology were studied as trends of technology to produce synthetic gas, and a project was proposed for technical development of using natural gas as liquid fuel in Japan. In the survey of technology against the surplus aromatic hydrocarbon, studied were the benzene law regulation and the supply/demand trend of aromatic hydrocarbon, process to reduce production of aromatic hydrocarbon as much as possible, process to reduce aromatics of the produced petroleum products, and process to effectively use aromatic hydrocarbon as chemical raw material. In the survey of high grade treatment of petroleum coke, studied were a possibility of using HS petroleum coke in the DIOS method, iron bath gasification, and copper bath gasification technology. 108 refs., 146 figs., 103 tabs.

A tiered analytical protocol for the characterization of heavy oil residues at petroleum-contaminated hazardous waste sites

International Nuclear Information System (INIS)

Pollard, S.J.T.; Kenefick, S.L.; Hrudey, S.E.; Fuhr, B.J.; Holloway, L.R.; Rawluk, M.

1994-01-01

The analysis of hydrocarbon-contaminated soils from abandoned refinery sites in Alberta, Canada is used to illustrate a tiered analytical approach to the characterization of complex hydrocarbon wastes. Soil extracts isolated from heavy oil- and creosote-contaminated sites were characterized by thin layer chromatography with flame ionization detection (TLC-FID), ultraviolet fluorescence, simulated distillation (GC-SIMDIS) and chemical ionization GC-MS analysis. The combined screening and detailed analytical methods provided information essential to remedial technology selection including the extent of contamination, the class composition of soil extracts, the distillation profile of component classes and the distribution of individual class components within various waste fractions. Residual contamination was characteristic of heavy, degraded oils, consistent with documented site operations and length of hydrocarbon exposure at the soil surface

Biodegradasi Petroleum dan Hidrokarbon Eikosana oleh Isolat Bakteri Pseudomonas aeruginosa

Directory of Open Access Journals (Sweden)

Faiqah Umar

2015-01-01

Full Text Available Biodegradation of petroleum and hydrocarbon eicosane by Pseudomonas aeruginosa isolate. Hydrocarbon are important environmental contaminants in soil and water. These compounds have a potential risk to human health, as many of them are carsinogenic and toxic to marine organisms such as diatome, gasthrophode, mussel, and fish. The purpose of this research was to know the ability of Pseudomonas aeruginosa to degradate the hydrocarbon (petroleum Hundill and eicosane substrate. Growing test used in two steps, the preculture and culture step. The biodegradation capacity was measured by quantitative and qualitative tests. The essay showed an increasing biodegradation capacitypercentage of bacteria cell mass on hydrocarbon substrate. The percentage on petroleum Hundill substrat as follows; log phase was 51,6%, descelerate phase was 73%, and linear phase was 81,4%. On eicosane substrate as follows; log phase was 62,7%, descelerate phase was 85,2%, and linear phase was 85,2%. The qualitative biodegradation capacity by chromatography result showed separate enchained of carbon n-alkana in each growth phase on petroleum Hundill substrate. Carbon chain termination as follows; C11, C12, C14, C15, C16, C18, C22 on log phase, C12, C17, C19, C20, C24 on descelerate phase, and C12 until C25 even better on linear phase.

Identifying the source of petroleum pollution in sediment cores of southwest of the Caspian Sea using chemical fingerprinting of aliphatic and alicyclic hydrocarbons.

Science.gov (United States)

Shirneshan, Golshan; Bakhtiari, Alireza Riyahi; Memariani, Mahmoud

2017-02-15

In this study, the concentration and sources of aliphatic and petroleum markers were investigated in 105 samples of Anzali, Rezvanshahr and Astara cores from the southwest of Caspian Sea. Petroleum importation was diagnosed as a main source in most depths of cores by the results of unresolved complex mixture, carbon preference index and hopanes and steranes. From the chemical diagnostic parameters, petroleum inputs in sediment of cores were determined to be different during years and the sources of hydrocarbons in some sections differed than Anzali and Turkmenistan and Azerbaijan oils. Diagenic ratios in most sediments of upper and middle sections in Astara core were determined to be highly similar to those of Azerbaijan oil, while the presence of Turkmenistan and Anzali oils were detected in a few sections of Anzali and Rezvanshahr cores and only five layers of downer section in Anzali core, respectively. Copyright © 2016. Published by Elsevier Ltd.

Characterization of hydrocarbon-degrading and biosurfactant-producing Pseudomonas sp. P-1 strain as a potential tool for bioremediation of petroleum-contaminated soil.

Science.gov (United States)

Pacwa-Płociniczak, Magdalena; Płaza, Grażyna Anna; Poliwoda, Anna; Piotrowska-Seget, Zofia

2014-01-01

The Pseudomonas sp. P-1 strain, isolated from heavily petroleum hydrocarbon-contaminated soil, was investigated for its capability to degrade hydrocarbons and produce a biosurfactant. The strain degraded crude oil, fractions A5 and P3 of crude oil, and hexadecane (27, 39, 27 and 13% of hydrocarbons added to culture medium were degraded, respectively) but had no ability to degrade phenanthrene. Additionally, the presence of gene-encoding enzymes responsible for the degradation of alkanes and naphthalene in the genome of the P-1 strain was reported. Positive results of blood agar and methylene blue agar tests, as well as the presence of gene rhl, involved in the biosynthesis of rhamnolipid, confirmed the ability of P-1 for synthesis of glycolipid biosurfactant. 1H and 13C nuclear magnetic resonance, Fourier transform infrared spectrum and mass spectrum analyses indicated that the extracted biosurfactant was affiliated with rhamnolipid. The results of this study indicate that the P-1 and/or biosurfactant produced by this strain have the potential to be used in bioremediation of hydrocarbon-contaminated soils.

Purifying hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Dunstan, A E

1918-06-03

Ligroin, kerosene, and other distillates from petroleum and shale oil, are purified by treatment with a solution of a hypochlorite containing an excess of alkali. The hydrocarbon may be poured into brine, the mixture stirred, and an electric current passed through. Heat may be applied.

Petroleum investment conditions in Peru

International Nuclear Information System (INIS)

Garcia Schreck, M.

1996-01-01

This report focuses on the current petroleum investment conditions in Peru, and Peru's hydrocarbon potential. Investment conditions are examined, and political risk, internal security, the economic environment, and the legal framework for investment are considered. (UK)

Concentration of petroleum-hydrocarbon contamination shapes fungal endophytic community structure in plant roots

Directory of Open Access Journals (Sweden)

Guillaume eBourdel

2016-05-01

Full Text Available Plant-root inhabiting fungi are a universal phenomenon found in all ecosystems where plants are able to grow, even in harsh environments. Interactions between fungi and plant roots can vary widely from mutualism to parasitism depending on many parameters. The role of fungal endophytes in phytoremediation of polluted sites, and characterization of the endophytic diversity and community assemblages in contaminated areas remain largely unexplored. In this study, we investigated the composition of endophytic fungal communities in the roots of two plant species growing spontaneously in petroleum-contaminated sedimentation basins of a former petro-chemical plant. The three adjacent basins showed a highly heterogeneous patterns of pollutant concentrations. We combined a culture-based isolation approach with the pyrosequencing of fungal ITS ribosomal DNA. We selected two species, Eleocharis erythropoda Steud. and Populus balsamifera L., and sampled three individuals of each species from each of three adjacent basins, each with a different concentration of petroleum hydrocarbons. We found that contamination level significantly shaped endophytic fungal diversity and community composition in E. erythropoda, with only 9.9% of these fungal Operational Taxonomic Units (OTUs retrieved in all three basins. However, fungal community structure associated with P. balsamifera remained unaffected by the contamination level with 28.2% of fungal OTUs shared among all three basins. This could be explained by the smaller differences of pollutant concentrations in the soil around our set of P. balsamifera sampless compared to that around our set of E. erythropoda samples. Our culture-based approach allowed isolation of 11 and 30 fungal endophytic species from surface-sterilized roots of E. erythropoda and P. balsamifera, respectively. These isolates were ribotyped using ITS, and all were found in pyrosequensing datasets. Our results demonstrate that extreme levels of

Evaluation of quicklime mixing for the remediation of petroleum contaminated soils.

Science.gov (United States)

Schifano, V; Macleod, C; Hadlow, N; Dudeney, R

2007-03-15

Quicklime mixing is an established solidification/stabilization technique to improve mechanical properties and immobilise contaminants in soils. This study examined the effects of quicklime mixing on the concentrations and leachability of petroleum hydrocarbon compounds, in two natural soils and on a number of artificial sand/kaolinite mixtures. Several independent variables, such as clay content, moisture content and quicklime content were considered in the study. After mixing the soils with the quicklime, pH, temperature, moisture content, Atterberg limits and concentrations of petroleum hydrocarbon compounds were determined on soil and leachate samples extracted from the treated soils. Significant decreases in concentrations of petroleum hydrocarbon compounds were measured in soils and leachates upon quicklime mixing, which may be explained by a number of mechanisms such as volatilization, degradation and encapsulation of the hydrocarbon compounds promoted by the quicklime mixing. The increase in temperature due to the exothermic hydration reaction of quicklime when in contact with porewater helps to volatilize the light compounds but may not be entirely responsible for their concentration decreases and for the decrease of heavy aliphatics and aromatics concentrations.

[Analysis of fluorescence spectrum of petroleum-polluted water].

Science.gov (United States)

Huang, Miao-Fen; Song, Qing-Jun; Xing, Xu-Feng; Jian, Wei-Jun; Liu, Yuan; Zhao, Zu-Long

2014-09-01

In four ratio experiments, natural waters, sampled from the mountain reservoir and the sea water around Dalian city, were mixed with the sewage from petroleum refinery and petroleum exploitation plants. The fluorescence spectra of water samples containing only chromophoric dissolved organic matters(CDOM), samples containing only petroleum, and samples containing a mixture of petroleum and CDOM were analyzed, respectively. The purpose of this analysis is to provide a basis for determining the contribution of petroleum substances and CDOM to the total absorption coefficient of the petroleum-contaminated water by using fluorescence technique. The results showed that firstly, CDOM in seawater had three main fluorescence peaks at Ex: 225-230 nm/Em: 320-330 nm, Ex: 280 nm/Em: 340 nm and Ex: 225-240 nm/Em: 430-470 nm, respectively, and these may arise from the oceanic chlorophyll. CDOM in natural reservoir water had two main fluorescence peaks at EX: 240- 260 nm/Em: 420-450 nm and Ex: 310~350 nm/Em: 420--440 nm, respectively, and these may arise from the terrestrial sources; secondly, the water samples containing only petroleum extracted with n-hexane had one to three fluorescence spectral peaksat Ex: 220-240 nm/Em: 320-340 nm, Ex: 270-290 nm/Em: 310-340 nm and Ex: 220-235 nm/Em: 280-310 nm, respectively, caused by their hydrocarbon component; finally, the water samples containing both petroleum and CDOM showed a very strong fluorescence peak at Ex: 230-250 nm/Em: 320-370 nm, caused by the combined effect of CDOM and petroleum hydrocarbons.

Bioremediation of petroleum-contaminated soil: A Review

Science.gov (United States)

Yuniati, M. D.

2018-02-01

Petroleum is the major source of energy for various industries and daily life. Releasing petroleum into the environment whether accidentally or due to human activities is a main cause of soil pollution. Soil contaminated with petroleum has a serious hazard to human health and causes environmental problems as well. Petroleum pollutants, mainly hydrocarbon, are classified as priority pollutants. The application of microorganisms or microbial processes to remove or degrade contaminants from soil is called bioremediation. This microbiological decontamination is claimed to be an efficient, economic and versatile alternative to physicochemical treatment. This article presents an overview about bioremediation of petroleum-contaminated soil. It also includes an explanation about the types of bioremediation technologies as well as the processes.

Distribution and concentrations of petroleum hydrocarbons associated with the BP/Deepwater Horizon Oil Spill, Gulf of Mexico.

Science.gov (United States)

Sammarco, Paul W; Kolian, Steve R; Warby, Richard A F; Bouldin, Jennifer L; Subra, Wilma A; Porter, Scott A

2013-08-15

We examined the geographic extent of petroleum hydrocarbon contamination in sediment, seawater, biota, and seafood during/after the BP/Deepwater Horizon Oil Spill (April 20-July 15, 2010; 28.736667°N, -88.386944°W). TPH, PAHs, and 12 compound classes were examined, particularly C1-benzo(a)anthracenes/chrysenes, C-2-/C-4-phenanthrenes/anthracenes, and C3-naphthalenes. Sediment TPH, PAHs, and all classes peaked near Pensacola, Florida, and Galveston, Texas. Seawater TPH peaked off Pensacola; all of the above classes peaked off the Mississippi River, Louisiana and Galveston. Biota TPH and PAHs peaked near the Mississippi River; C-3 napthalenes peaked near the spill site. Seafood TPH peaked near the spill site, with PAHs and all classes peaking near Pensacola. We recommend that oil concentrations continued to be monitored in these media well after the spill has ceased to assist in defining re-opening dates for fisheries; closures should be maintained until hydrocarbon levels are deemed within appropriate limits. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Effect of petroleum hydrocarbons in copper phytoremediation by a salt marsh plant (Juncus maritimus) and the role of autochthonous bioaugmentation.

Science.gov (United States)

Montenegro, I P F M; Mucha, A P; Reis, I; Rodrigues, P; Almeida, C M R

2016-10-01

This work aimed to investigate, under controlled but environmental relevant conditions, the effects of the presence of both inorganic and organic contaminants (copper and petroleum hydrocarbons) on phytoremediation potential of the salt marsh plant Juncus maritimus. Moreover, bioaugmentation, with an autochthonous microbial consortium (AMC) resistant to Cu, was tested, aiming an increase in the remediation potential of this plant in the presence of a co-contamination. Salt marsh plants with sediment attached to their roots were collected, placed in vessels, and kept in greenhouses, under tidal simulation. Sediments were contaminated with Cu and petroleum, and the AMC was added to half of the vessels. After 5 months, plants accumulated significant amounts of Cu but only in belowground structures. The amount of Cu was even higher in the presence of petroleum. AMC addition increased Cu accumulation in belowground tissues, despite decreasing Cu bioavailability, promoting J. maritimus phytostabilization potential. Therefore, J. maritimus has potential to phytoremediate co-contaminated sediments, and autochthonous bioaugmentation can be a valuable strategy for the recovery and management of moderately impacted estuaries. This approach can contribute for a sustainable use of the environmental resources. Graphical abstract ᅟ.

PhytoPet : a database of plants that play a role in the phytoremediation of petroleum hydrocarbons

International Nuclear Information System (INIS)

Farrell, R.E.; Frick, C.M.; Germida, J.J.

2004-01-01

This support document summarized the results of botanical surveys conducted as part of a phytoremediation research project that catalogued plants found growing at a petroleum impacted site in Alberta. Phytoremediation refers to the growing of chosen plant species in a polluted site for a period of time in order for the plant to remove contaminants through its natural attributes of absorption, translocation, storage and excretion. Several different plant species with phytoremediation properties are being considered for wide scale bioremediation use. This document described the PhytoPet database which was originally developed as an inventory of plants with phytoremediation capabilities. It was designed to provide easy access to information and help users choose plants with the potential to phytoremediate petroleum hydrocarbons. The information in this document is intended for remediation specialists, site owners and managers as well as environmental scientists in assessing the suitability of phytoremediation as a tool for the remediation and restoration of petroleum impacted sites. The document contains detailed data on the research objectives of each botanical survey and experimental conditions under which each plant's phytoremediation potential was evaluated. PhytoPet is interactive, allowing researchers to submit data on new studies to an administrated website that verifies the data before adding it to an on-line database. The database is grouped by experimental data and plant specific data. A brief description of individual plants and their mechanism of phytoremediation was presented. Plant specific data include information on the taxonomy, habitat, biology, and distribution of each plant in the database. refs., tabs., figs

Evaluation of total petroleum hydrocarbons (TPH in urban soil from Maicao, Colombia

Directory of Open Access Journals (Sweden)

Martha L. Castellanos

2015-09-01

Full Text Available The presence of total petroleum hydrocarbons (TPH and their effects on soil properties in urban area of Maicao, Colombia, was evaluated. 18 sites were selected: nine contaminated and nine non-contaminated and two depths (0-30 cm and 30-60 cm were evaluated. The medium TPH fraction (Soxhlet reflux method, EPA 3540C and heavy TPH fraction (Soxhlet reflux method, EPA 3550C were extracted. TPH were identified by gas chromatography with flame ionization detector (GC-FID. Soil parameters related potential adsorption were determined: pH, electrical conductivity (EC, organic carbon (OC, cation exchange capacity (CEC, texture; soil moisture retention, aggregate stability. High contents of TPH was found in all fractions. No significant changes were found for texture and (EC. There was an increase in the content of OC (500%, soil aggregation and aggregate stability (200%; slight decrease pH, CEC and soil moisture retention (23.5% soil surface. These results show the vulnerability of the urban soils to the TPH contamination and exposure of the human population to these contaminants.

Crude petroleum-oil biodegradation efficiency of Bacillus subtilis and Pseudomonas aeruginosa strains isolated from a petroleum-oil contaminated soil from North-East India.

Science.gov (United States)

Das, Kishore; Mukherjee, Ashis K

2007-05-01

The efficiency of Bacillus subtilis DM-04 and Pseudomonas aeruginosa M and NM strains isolated from a petroleum contaminated soil sample from North-East India was compared for the biodegradation of crude petroleum-oil hydrocarbons in soil and shake flask study. These bacterial strains could utilize crude petroleum-oil hydrocarbons as sole source of carbon and energy. Bioaugmentation of TPH contaminated microcosm with P. aeruginosa M and NM consortia and B. subtilis strain showed a significant reduction of TPH levels in treated soil as compared to control soil at the end of experiment (120 d). P. aeruginosa strains were more efficient than B. subtilis strain in reducing the TPH content from the medium. The plate count technique indicated expressive growth and biosurfactant production by exogenously seeded bacteria in crude petroleum-oil rich soil. The results showed that B. subtilis DM-04 and P. aeruginosa M and NM strains could be effective for in situ bioremediation.

Enzymatic bioremediation of polyaromatic hydrocarbons by fungal consortia enriched from petroleum contaminated soil and oil seeds.

Science.gov (United States)

Balaji, V; Arulazhagan, P; Ebenezer, P

2014-05-01

The present study focuses on fungal strains capable of secreting extracellular enzymes by utilizing hydrocarbons present in the contaminated soil. Fungal strains were enriched from petroleum hydrocarbons contaminated soil samples collected from Chennai city, India. The potential fungi were isolated and screened for their enzyme secretion such as lipase, laccase, peroxidase and protease and also evaluated fungal enzyme mediated PAHs degradation. Total, 21 potential PAHs degrading fungi were isolated from PAHs contaminated soil, which belongs to 9 genera such as Aspergillus, Curvularia, Drechslera, Fusarium, Lasiodiplodia, Mucor Penicillium, Rhizopus, Trichoderma, and two oilseed-associated fungal genera such as Colletotrichum and Lasiodiplodia were used to test their efficacy in degradation of PAHs in polluted soil. Maximum lipase production was obtained with P. chrysogenum, M. racemosus and L. theobromae VBE1 under optimized cultural condition, which utilized PAHs in contaminated soil as sole carbon source. Fungal strains, P. chrysogenum, M. racemosus and L. theobromae VBE1, as consortia, used in the present study were capable of degrading branched alkane isoprenoids such as pristine (C17) and pyrene (C18) present in PAHs contaminated soil with high lipase production. The fungal consortia acts as potential candidate for bioremediation of PAHs contaminated environments.

Colombian petroleum - A good business

International Nuclear Information System (INIS)

Carta Petrolera

1998-01-01

A great interest exists for Colombia, a country in which the statistics of petroleum and gas production, have been shot to volumes record; where 15 new contracts are signed every year, arriving in December from 1997 to an effective figure record of 107, a country that see grow their exports of raw; a country that every time has more facilities of transport and commercialization of hydrocarbons and it receives to more companies interested in sharing the risk in petroleum search

Management of the solid waste in perforation projects exploratory hydrocarbons; Manejo de los residuos solidos en proyectos de perforacion exploratoria de hidrocarburos

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Miranda, J.P.

2010-07-01

This paper describes de considerations for solid waste management in hydrocarbons exploration projects, as the serious environmental affectation as a function of soil contamination by leachate form the temporary storage of contaminated industrial waste hydrocarbons, altered by the presence of deposits landscaping waste materials, pollution of water and vegetation and the production of odors.

Petroleum business of high risk

International Nuclear Information System (INIS)

Carta Petrolera

2001-01-01

The paper is about the economic risk and of the geologic risk that assist the industry of the petroleum; an analysis of these types of risk, possibilities of success and investments to carry out in the search of hydrocarbons are made

Our petroleum challenge : sustainability into the 21. century. 7. ed.

International Nuclear Information System (INIS)

Bott, R.D.; Carson, D.M.; Henderson, J.W.

2004-01-01

The Canadian Centre for Energy Information provides accurate information on all aspects of Canada's energy sector. This report reviews Canada's petroleum resources and the role they play in society. In particular, it discussed the origins of crude oil and natural gas, exploration, production, processing, transportation, refining, marketing and end-use. The report is intended for a diverse audience interested in hydrocarbons, natural gas, crude oil, bitumen, gasoline, petroleum, natural gas liquids, and liquefied natural gas. The report explains the science and technology of the upstream and downstream petroleum industry. Canada's hydrocarbon legacy was described in the first section, followed by exploration, land use, seismic surveys, drilling, and production issues. The challenges and opportunities facing the industry in the twenty-first century were also discussed with reference to sustainable development. Business aspects were also outlined in terms of revenues, public interest, petroleum prices, and employment. refs., tabs., figs

Non-woven Textile Materials from Waste Fibers for Cleanup of Waters Polluted with Petroleum and Oil Products

Science.gov (United States)

Neznakomova, Margarita; Boteva, Silvena; Tzankov, Luben; Elhag, Mohamed

2018-04-01

The aim of this work was to investigate the possibility of using non-woven materials (NWM) from waste fibers for oil spill cleanup and their subsequent recovery. Manufacture of textile and readymade products generates a significant amount of solid waste. A major part of it is deposited in landfills or disposed of uncontrollably. This slowly degradable waste causes environmental problems. In the present study are used two types of NWM obtained by methods where waste fibers are utilized. Thus, real textile products are produced (blankets) with which spills are covered and removed by adsorption. These products are produced by two methods: the strengthening of the covering from recovered fibers is made by entanglement when needles of special design pass through layers (needle-punching) or by stitching with thread (technology Maliwatt). Regardless of the random nature of the fiber mixture, the investigated products are good adsorbents of petroleum products. The nature of their structure (a significant void volume and developed surface) leads to a rapid recovery of the spilled petroleum products without sinking of the fiber layer for the sampled times. The used NWM can be burned under special conditions.

Applications of biosurfactants in the petroleum industry and the remediation of oil spills.

Science.gov (United States)

de Cássia F S Silva, Rita; Almeida, Darne G; Rufino, Raquel D; Luna, Juliana M; Santos, Valdemir A; Sarubbo, Leonie Asfora

2014-07-15

Petroleum hydrocarbons are important energy resources. However, petroleum is also a major pollutant of the environment. Contamination by oil and oil products has caused serious harm, and increasing attention has been paid to the development and implementation of innovative technologies for the removal of these contaminants. Biosurfactants have been extensively used in the remediation of water and soil, as well as in the main stages of the oil production chain, such as extraction, transportation, and storage. This diversity of applications is mainly due to advantages such as biodegradability, low toxicity and better functionality under extreme conditions in comparison to synthetic counterparts. Moreover, biosurfactants can be obtained with the use of agro-industrial waste as substrate, which helps reduce overall production costs. The present review describes the potential applications of biosurfactants in the oil industry and the remediation of environmental pollution caused by oil spills.

Applications of Biosurfactants in the Petroleum Industry and the Remediation of Oil Spills

Directory of Open Access Journals (Sweden)

Rita de Cássia F. S. Silva

2014-07-01

Full Text Available Petroleum hydrocarbons are important energy resources. However, petroleum is also a major pollutant of the environment. Contamination by oil and oil products has caused serious harm, and increasing attention has been paid to the development and implementation of innovative technologies for the removal of these contaminants. Biosurfactants have been extensively used in the remediation of water and soil, as well as in the main stages of the oil production chain, such as extraction, transportation, and storage. This diversity of applications is mainly due to advantages such as biodegradability, low toxicity and better functionality under extreme conditions in comparison to synthetic counterparts. Moreover, biosurfactants can be obtained with the use of agro-industrial waste as substrate, which helps reduce overall production costs. The present review describes the potential applications of biosurfactants in the oil industry and the remediation of environmental pollution caused by oil spills.

Development of oil hydrocarbon fingerprinting and identification techniques

International Nuclear Information System (INIS)

Wang Zhendi; Fingas, Merv F.

2003-01-01

Oil, refined product, and pyrogenic hydrocarbons are the most frequently discovered contaminants in the environment. To effectively determine the fate of spilled oil in the environment and to successfully identify source(s) of spilled oil and petroleum products is, therefore, extremely important in many oil-related environmental studies and liability cases. This article briefly reviews the recent development of chemical analysis methodologies which are most frequently used in oil spill characterization and identification studies and environmental forensic investigations. The fingerprinting and data interpretation techniques discussed include oil spill identification protocol, tiered analytical approach, generic features and chemical composition of oils, effects of weathering on hydrocarbon fingerprinting, recognition of distribution patterns of petroleum hydrocarbons, oil type screening and differentiation, analysis of 'source-specific marker' compounds, determination of diagnostic ratios of specific oil constituents, stable isotopic analysis, application of various statistical and numerical analysis tools, and application of other analytical techniques. The issue of how biogenic and pyrogenic hydrocarbons are distinguished from petrogenic hydrocarbons is also addressed

Petroleum apocalypse

International Nuclear Information System (INIS)

Cochet, Y.

2005-09-01

Oil prices are increasing while current explanations for this phenomenon are no longer satisfactory. The cheap petroleum era is ending and this problem can seriously convulse our lifestyles. Transports, agriculture, plastics, clothes, medicines: petroleum is everywhere. This is why the rise of hydrocarbons price will not be a simple economic shock but the end of the world like the one we know. However, it is still possible to postpone this event to a later date and to limit its effects by the implementation of a new oil sobriety era. This implies to already organize the decay of materials and energy consumption, together with keeping solidarity, democracy and peace up. In this condition only the transition will be less painful. (J.S.)

Comparison of the composition between coal-liquid naphtha and petroleum gasoline

Energy Technology Data Exchange (ETDEWEB)

Miki, Y.; Sugimoto, Y.; Ono, S.; Machida, M. [National Chemical Laboratory for Industry, Tsukuba (Japan)

1997-08-01

Compositional characterization was performed using a gas chromatography-mass spectrometry-atomic emission detector technique on coal-liquid raw naphtha, coal-liquid refined naphtha, coal-liquid reformate and commercial petroleum gasoline. The chemical composition of these oils are divided into five groups: chain hydrocarbons, monocyclic hydrocarbons, bicyclic hydrocarbons, oxygen-containing compounds and other compounds (containing unidentified compounds). Compared to petroleum gasoline, the coal-liquid raw naphtha contains higher concentrations of straight paraffins, cycloparaffins, cycloolefins, bicycloparaffins and oxygen-containing compounds, and contains lower concentrations of brached paraffins and monocyclic aromatic compounds. Phenols and ketones are the major components of oxygen-containing compounds. The total concentration of paraffins and cycloparaffins increased after refining. The hydrogenation of olefins and the hydrodeoxygenation of oxygen-containing compounds are suggested to proceed during the refining process. The reforming treatment increased the concentrations of branched paraffins and monocyclic aromatic compounds; this suggests that coal-liquid reformat could be used as a major blending substance with petroleum gasoline.

Hydrous pyrolysis/oxidation process for in situ destruction of chlorinated hydrocarbon and fuel hydrocarbon contaminants in water and soil

Science.gov (United States)

Knauss, Kevin G.; Copenhaver, Sally C.; Aines, Roger D.

2000-01-01

In situ hydrous pyrolysis/oxidation process is useful for in situ degradation of hydrocarbon water and soil contaminants. Fuel hydrocarbons, chlorinated hydrocarbons, polycyclic aromatic hydrocarbons, petroleum distillates and other organic contaminants present in the soil and water are degraded by the process involving hydrous pyrolysis/oxidation into non-toxic products of the degradation. The process uses heat which is distributed through soils and water, optionally combined with oxygen and/or hydrocarbon degradation catalysts, and is particularly useful for remediation of solvent, fuel or other industrially contaminated sites.

Biodegradation of low and high molecular weight hydrocarbons in petroleum refinery wastewater by a thermophilic bacterial consortium.

Science.gov (United States)

Pugazhendi, Arulazhagan; Abbad Wazin, Hadeel; Qari, Huda; Basahi, Jalal Mohammad Al-Badry; Godon, Jean Jacques; Dhavamani, Jeyakumar

2017-10-01

Clean-up of contaminated wastewater remains to be a major challenge in petroleum refinery. Here, we describe the capacity of a bacterial consortium enriched from crude oil drilling site in Al-Khobar, Saudi Arabia, to utilize polycyclic aromatic hydrocarbons (PAHs) as sole carbon source at 60°C. The consortium reduced low molecular weight (LMW; naphthalene, phenanthrene, fluorene and anthracene) and high molecular weight (HMW; pyrene, benzo(e)pyrene and benzo(k)fluoranthene) PAH loads of up to 1.5 g/L with removal efficiencies of 90% and 80% within 10 days. PAH biodegradation was verified by the presence of PAH metabolites and evolution of carbon dioxide (90 ± 3%). Biodegradation led to a reduction of the surface tension to 34 ± 1 mN/m thus suggesting biosurfactant production by the consortium. Phylogenetic analysis of the consortium revealed the presence of the thermophilic PAH degrader Pseudomonas aeruginosa strain CEES1 (KU664514) and Bacillus thermosaudia (KU664515) strain CEES2. The consortium was further found to treat petroleum wastewater in continuous stirred tank reactor with 96 ± 2% chemical oxygen demand removal and complete PAH degradation in 24 days.

Toxicity and toxicokinetics of binary combinations of petroleum hydrocarbon distillates with the earthworm Eisenia andrei.

Science.gov (United States)

Cermak, Janet; Stephenson, Gladys; Birkholz, Detlef; Dixon, D George

2013-04-01

Petroleum hydrocarbons (PHCs) act via narcosis and are expected to have additive toxicity. However, previous work has demonstrated less-than-additive toxicity with PHC distillates and earthworms. A study was initiated to investigate this through toxicity and toxicokinetic studies with the earthworm Eisenia andrei. Three petroleum distillate fractions, F2 (>C10-C16), F3a (>C16-C23), and F3b (>C23-C34), were used in two binary combinations, F2F3a and F3aF3b. In the toxicity study, clean soil was spiked with equitoxic combinations of the two distillates ranging from 0.5 to 2.5 toxic units. In the toxicokinetic study, a binary combination consisting of one concentration of each distillate was used. On a soil concentration basis, the toxicity of the binary combinations of distillates was less than additive. Accumulation of the individual distillates, however, was generally reduced when a second distillate was present, resulting in lower body burden. This is thought to be due to the presence of a nonaqueous-phase liquid at the soil concentrations used. On a tissue concentration basis, toxicity was closer to additive. The results demonstrate that tissue concentrations are the preferred metric for toxicity for earthworms. They also demonstrate that the Canada-wide soil standards based on individual distillates are likely protective. Copyright © 2013 SETAC.

Utilization of the waste gases from a petroleum refinery as fuel

International Nuclear Information System (INIS)

Torres Contreras, Jose Francisco

2012-01-01

The fuels waste gases that are burned in a flare stack were proposed as an alternative for its utilization. The current operation of the flare stack system of a petroleum refinery was analyzed. The historical information of the equipment and original design of the same was used. From the calculations that were performed, it is expected that the delivered heat for the flare gases approaching to 65 MJ/M 3 , so it would be an effective fuel for be used in furnaces and boilers. A new flare stack system and a system for recovery of the waste gases of process is proposed. The new flare stack system must have a liquid separator of 2,3 meters of diameter, a length of 6,4 meters and a capacity of 26,1 cubic meters. The velocity of the gas to the exit of the separator has been of 80,7 m/s. The liquid hydrocarbon flow that has exited the separator has been of 71 m 3 /h, with a speed of 0,91 m/s and a pump of 2,75 HP is required. The liquid seal of flare stack systems must have a minimum height of 1,05 m. The gas recovery system to burn in the flare stack should be located between the liquid separator and liquid seal of the flare stack systems. For an average consumption of 150 m 3 /h of fuel gas for furnaces and boilers, the gas recovery system must have with a compressor of 4,75 HP, a liquid separator of 50 m 3 and a pump of 2,50 HP. The gas recovery system has had with an absorber of 7 plates for washing of the stream acid gas with MEA, at 40 degrees celsius and an pressure of operating of 67 kPa, and a flow of 55,88 kg/h at amine solution. The flare gas flow has been recommended to be analyzed chemically, as well as the measurement of the flow of gas streams plant consumption and gases flare. A technical-economic feasibility study of the process should be realized. (author) [es

The use of field redox measurements in assessing remediation of ground water containing petroleum hydrocarbons and chlorinated organic compounds

International Nuclear Information System (INIS)

Warner, S.D.; Gallinatti, J.D.; Honniball, J.H.

1995-01-01

Field measurements of the reduction-oxidation (redox) condition of ground water were used to assess the effects of in situ remediation of ground water affected by petroleum hydrocarbons and chlorinated organic compounds at multiple sites in northern California. The redox condition of ground water, traditionally measured quickly and inexpensively using a meter that measures electrode potential (Eh), is a valuable parameter by which to assess the conditions that affect the relative stability of various chemicals in ground water. Although not specific to a given redox couple measurements obtained using the traditional Eh meter give a sense of the relative tendency for a ground water to be reducing or oxidizing by providing a measurement of the system Eh. Two cases demonstrate the use of ground water Eh measurements in assessing the effects of in situ ground water remediation. In the first case, ground water affected by petroleum hydrocarbons-gasoline (TPHg), and benzene, toluene, ethylbenzene, and xylenes (BTEX) (ambient Eh of -100 to +100 millivolts [mv]) was treated by injecting hydrogen peroxide to supply oxygen to the subsurface environment and stimulate microbial activity. The second case involved remediation of ground water containing chlorinated organic compounds. In this case, a subsurface permeable ground water treatment wall containing granular iron was installed across the flow path of the affected ground water. The in situ chemical treatment, which successfully dechlorinates compounds such as trichloroethylene, 1,2-dichloroethylene, and vinyl chloride, caused reducing conditions in the ground water, which resulted in the decrease in ground water Eh from am ambient reading of about -50 mv to about -400 mv

hydrocarbons biodegradation and evidence of mixed petroleum

African Journals Online (AJOL)

DJFLEX

MIXED PETROLEUM SOURCE INPUTS TO SURFACE. SEDIMENTS ... environmental risk assessment and remediation efforts. ... (station CR10), a distance of approximately 95km ... Cross River –near Oku Iboku beach area and ... extraction, and evapourated to near dryness ..... Ecological parameters of the mangrove.

Application of chemical tools to evaluate phytoremediation of weathered hydrocarbons

International Nuclear Information System (INIS)

Camp, H.; Kulakow, P.; Smart, D.R.; O'Reilly, K.

2002-01-01

The effectiveness of using phytoremediation methods to treat soils contaminated with hydrocarbons was tested in a three-year study at a site in northern California at a treatment pond for refinery process water. The treatment pond was drained several years ago and is targeted for cleanup. The petroleum hydrocarbons from the refinery waste were already highly degraded from natural weathering processes by the time the study began. The soil consists of about 23 per cent sand, 38 per cent silt, and 39 per cent clay. The study followed the Environmental Protection Agency's standardized field protocol and analytical approach. During the study, chemical data for several hydrocarbon parameters was gathered. Soil samples were Soxhlet-extracted in organic solvent and measured for oil and grease and total petroleum hydrocarbons using gravimetric techniques. One of the objectives was to develop an accurate quantitative way to identify sites and conditions where phytoremediation will be effective to supplement decision-tree-type approaches. The focus of the study is the application of chemical data in evaluating the effectiveness of the treatment process. Phytoremediation uses living plants for in situ remediation of polluted soils. The basic benefits of the techniques is that it is aesthetically pleasing, natural and passive. In addition, it is effective in cleaning up sites with low to moderate levels of pollution at shallow depths. A particular form of phytoremediation called rhizodegradation or enhanced rhizosphere biodegradation was the treatment used in this study. It is a treatment in which microorganisms digest organic substances and beak them down by biodegradation while being supported in the plant root structure. Test results indicate that the effects of phytoremediation treatments are subtle for highly weathered source material. It was noted that more statistical analysis will be performed with the data to determine compositional changes due to phytoremediation

Studies on the production of hydrocarbon mixtures from waste methyl ethyl ketone

International Nuclear Information System (INIS)

Kokitkar, P.B.; Roth, O.B.; Debelak, K.A.

1992-01-01

Large quantities of waste solvents are generated annually around the world in a large number of diverse industries, the paints and plastics industry being the largest consumer. The management of these waste solvents is becoming more and more difficult due to stricter environmental regulations by the EPA. The paint and allied products industry is expected to shift its solvent use from aliphatics and aromatics to oxygenated solvents to meet emissions and disposal standards. Many researchers have studied the dehydration reactions of oxygenated solvents to produce dehydration. However, most researchers have obtained only low molecular weight compounds (C 3 - C 4 hydrocarbons) from C 1 - C 4 alcohols and ketones. The kinetics of this class of reactions are not available in the open literature. The objective of this paper is to investigate the thermodynamic feasibility of this class of reactions and to compare the hydrocarbon products obtained using methylethyl ketone with regular unleaded gasoline

Distribution of petroleum hydrocarbons and organochlorinated contaminants in marine biota and coastal sediments from the ROPME Sea Area during 2005.

Science.gov (United States)

de Mora, Stephen; Tolosa, Imma; Fowler, Scott W; Villeneuve, Jean-Pierre; Cassi, Roberto; Cattini, Chantal

2010-12-01

The composition and spatial distribution of various petroleum hydrocarbons (PHs), comprising both aliphatic and polycyclic aromatic hydrocarbons (PAHs), and selected chlorinated pesticides and PCBs were measured in biota and coastal sediments from seven countries in the Persian Gulf and the Gulf of Oman (Bahrain, Iran, Kuwait, Oman, Qatar, Saudi Arabia and the United Arab Emirates). Evidence of extensive marine contamination with respect to organochlorinated compounds and PHs was not observed. Only one site, namely the BAPCO oil refinery in Bahrain, was considered to be chronically contaminated. Comparison of the results from this survey for Σ DDTs and Σ PCBs in rock oysters from the Gulf of Oman with similar measurements made at the same locations over the past two decades indicates a temporal trend of overall decreasing Σ PCB concentrations in oysters, whereas Σ DDTs levels have little changed during that period. Copyright © 2010 Elsevier Ltd. All rights reserved.

Petroleum industry opportunities in Guatemala

International Nuclear Information System (INIS)

1991-01-01

The investment opportunities that Guatemala has to offer in the petroleum sector are discussed, highlighting aspects of legislation as well as investment recovery. The increase in seismic and geological information that Guatemala has recently accumulated allows for an increased level of success in petroleum exploration, which coupled with an increase in basic infrastructure and the experience acquired in the administration of the hydrocarbons law, make it more attractive for foreign investment. An overview is presented of the sedimentary basins present, exploratory activity, surface reconnaissance permits, production sharing contracts, prices, taxation, royalties, and options. 7 figs

Effect of NiO/SiO2 on thermo-chemical conversion of waste cooking oil to hydrocarbons

Directory of Open Access Journals (Sweden)

J. Sani

2017-05-01

Full Text Available Increase in organic waste generation, dwindling nature of global oil reserves coupled with environmental challenges caused by waste oil disposal and burning of fossil fuels necessitated the need for alternative energy resources. Waste cooking oil obtained from the frying fish outlet was analyzed for its physicochemical properties using ASTM D-975 methods. Acid and Iodine values of the oil were 30.43 ± 0.32 mgKOH/g and 57.08 ± 0.43 mgI2/100 g respectively. Thermo-chemical conversion of the oil using NiO/SiO2 at different reaction conditions (pressure, temperature, and catalyst concentration at a residence time of 3 h yielded 33.63% hydrocarbons. Hydro-catalytic pyrolysis of waste cooking oil at 400 °C, H2 pressure of 15 bars, and catalyst to oil ratio of 0.25 g/100 cm3 resulted in highest hydrocarbon yield (41.98%. The fuel properties of the product were: cetane number (71.16, high heating value (41.43 MJ/kg, kinematic viscosity (2.01 mm2/s, density (0.94 g/ml, saponification value (185.1 ± 3.96 mgKOH/g, and iodine value (20.57 ± 0.20 I2/100 g respectively. These results show that the NiO/SiO2 could be a suitable catalyst for conversion of waste vegetable oil to hydrocarbons. Keywords: Energy, Chemical engineering

Hydrocarbons biodegradation and evidence of mixed petroleum ...

African Journals Online (AJOL)

Chromatographic analysis of extracts from the Cross River system show evidence of variable composition of biogenic n-alkane profile with dominance of terrigenous over aquatic organic matter present (LHC/SHC-0.36-10.57) at upstream location reflecting the natural background levels and marked levels of petroleum ...

Toxicity of vapor phase petroleum contaminants to microbial degrader communities

International Nuclear Information System (INIS)

Long, S.C.; Davey, C.A.

1994-01-01

Petroleum products constitute the largest quantity of synthetic organic chemical products produced in the US. They are comprised of mostly hydrocarbon constituents from many different chemical classes including alkenes, cycloalkanes, aromatic compounds, and polyaromatic hydrocarbons. Many petroleum constituents are classified as volatile organic compounds or VOCs. Petroleum products also constitute a major portion of environmental pollution. One emerging technology, with promise for applications to VOCs in subsurface soil environments, is bioventing coupled with soil vapor extraction. These technologies involve volatilization of contaminants into the soil gas phase by injection and withdrawal of air. This air movement causes enhancement of the aerobic microbial degradation of the mobilized vapors by the indigenous populations. This study investigated the effects of exposure of mixed, subsurface microbial communities to vapor phase petroleum constituents or vapors of petroleum mixtures. Soil slurries were prepared and plated onto mineral salts agar plates and exposed to vapor phase contaminants at equilibrium with pure product. Representative n-alkane, branched alkane, cycloalkane, and aromatic compounds were tested as well as petroleum product mixtures. Vapor exposure altered the numbers and morphologies of the colonies enumerated when compared to controls. However, even at high, equilibrium vapor concentrations, microbial degrader populations were not completely inhibited

Pelagic tar, dissolved/dispersed petroleum hydrocarbons and plastic distribution in the Cretan Sea, Greece

Energy Technology Data Exchange (ETDEWEB)

Kornilios, S.; Drakopoulos, P.G.; Dounas, C. [Institute of Marine Biology of Crete, Iraklio (Greece). Environmental Dept.

1998-12-01

During the first cruise of R/V `Philia` in July 1997 within the framework of the TALOS programme supported by the Greek Ministry of Physical Planning and Public Works, the sampling of floating tar, litter and sea water for dissolved/dispersed petroleum hydrocarbons (DDPH) was carried out in the Cretan Sea. Analysis of these data has allowed a first assessment of the status of floating marine pollution in the region. DDPH measurements showed a mean concentration of 0.145 {mu}g/l of chrysene equivalents (n = 24). Tar and plastics concentrations were in the range of 1-4280 and 0-1160 {mu}g/m{sup 2}, respectively. Mean pelagic tar concentration was 318 {mu}g/m{sup 2}, more than two times higher than what was reported for the area in previous studies. Based on in situ hydrographic observations there is strong evidence that most of the floating tar enters the Cretan Sea through the Ionian Sea. (author)

Pelagic tar, dissolved/dispersed petroleum hydrocarbons and plastic distribution in the Cretan Sea, Greece

Energy Technology Data Exchange (ETDEWEB)

Kornilios, S.; Drakopoulos, P.G.; Dounas, C. [Institute of Marine Biology of Crete, Iraklio (Greece). Environmental Dept.

1998-12-01

During the first cruise of R/V 'Philia' in July 1997 within the framework of the TALOS programme supported by the Greek Ministry of Physical Planning and Public Works, the sampling of floating tar, litter and sea water for dissolved/dispersed petroleum hydrocarbons (DDPH) was carried out in the Cretan Sea. Analysis of these data has allowed a first assessment of the status of floating marine pollution in the region. DDPH measurements showed a mean concentration of 0.145 {mu}g/l of chrysene equivalents (n = 24). Tar and plastics concentrations were in the range of 1-4280 and 0-1160 {mu}g/m{sup 2}, respectively. Mean pelagic tar concentration was 318 {mu}g/m{sup 2}, more than two times higher than what was reported for the area in previous studies. Based on in situ hydrographic observations there is strong evidence that most of the floating tar enters the Cretan Sea through the Ionian Sea. (author)

Pelagic tar, dissolved/dispersed petroleum hydrocarbons and plastic distribution in the Cretan Sea, Greece

International Nuclear Information System (INIS)

Kornilios, S.; Drakopoulos, P.G.; Dounas, C.

1998-01-01

During the first cruise of R/V 'Philia' in July 1997 within the framework of the TALOS programme supported by the Greek Ministry of Physical Planning and Public Works, the sampling of floating tar, litter and sea water for dissolved/dispersed petroleum hydrocarbons (DDPH) was carried out in the Cretan Sea. Analysis of these data has allowed a first assessment of the status of floating marine pollution in the region. DDPH measurements showed a mean concentration of 0.145 μg/l of chrysene equivalents (n = 24). Tar and plastics concentrations were in the range of 1-4280 and 0-1160 μg/m 2 , respectively. Mean pelagic tar concentration was 318 μg/m 2 , more than two times higher than what was reported for the area in previous studies. Based on in situ hydrographic observations there is strong evidence that most of the floating tar enters the Cretan Sea through the Ionian Sea. (author)

Bioremediation of petroleum-contaminated soil

International Nuclear Information System (INIS)

Pearce, K.; Snyman, H.G.; Oellermann, R.A.; Gerber, A.

1995-01-01

A pilot-scale study was conducted to evaluate the application of land-farming techniques in bioremediating a soil highly contaminated with petroleum products. A commercial biosupplement, and one prepared with indigenous microorganisms from the contaminated soil, were tested. Application of either of the biosupplements, in addition to the control of pH, moisture, and oxygen levels, resulted in a 94% reduction of the initial total petroleum hydrocarbon concentration (TPHC) (32% mass/mass) over a 70-day period. Implementation of these findings at full scale to bioremediate highly weathered petroleum products showed an average reduction of 89% over 5.5 months. Target levels of 1,400 mg/kg soil were reached from an initial average TPHC concentration of 12,200 mg/kg soil

World-wide and regional intercomparison for the determination of organochlorine compounds and petroleum hydrocarbons in mussel sample IAEA-142. Report no. 59

International Nuclear Information System (INIS)

Villeneuve, J.P.; Horvat, M.; Cattini, C.

1996-03-01

The accurate and precise determination of organochlorine compounds and petroleum hydrocarbons in marine environmental samples is an important aspect of marine pollution assessments in coastal and ocean environments. Intercomparison exercises represent an essential element of method testing and are used as a basic tool for evaluating data quality on a global and regional level. The Marine Environmental Studies Laboratory (MESL) of IAEA-MEL has conducted intercomparison exercises on trace organic compounds for over nineteen years as part of its contribution to IAEA's analytical quality control service and UNEP's regional seas programme, and occasionally in association with the intergovernmental oceanographic commission (of UNESCO) GIPME programme. These exercises are organized on a continuous basis, at least once per year. Result of previous exercises have revealed serious problems for many regional laboratories to obtain comparable data. As a consequence of this situation, it was decided to seek increased support for quality assurance programmes. Staff of MESL, with funding from UNEP, the World Bank and regional trust funds, embarked on a campaign to train analysts in modern measurement techniques, supply appropriate and reliable reference methods and materials and, where possible, to improve analytical instruments in Member State laboratories. This report describes results of the IAEA/UNEP intercomparison run 142 for the chemical analysis of organochlorine compounds and petroleum hydrocarbons in a homogenised mussel sample

Screening of biosurfactant producers from petroleum hydrocarbon contaminated sources in cold marine environments.

Science.gov (United States)

Cai, Qinhong; Zhang, Baiyu; Chen, Bing; Zhu, Zhiwen; Lin, Weiyun; Cao, Tong

2014-09-15

An overview of literature about isolating biosurfactant producers from marine sources indicated no such producers have been reported form North Atlantic Canada. Water and sediment samples were taken from petroleum hydrocarbon contaminated coastal and offshore areas in this region. Either n-hexadecane or diesel was used as the sole carbon source for the screening. A modified colony-based oil drop collapsing test was used to cover sessile biosurfactant producers. Fifty-five biosurfactant producers belong to genera of Alcanivorax, Exiguobacterium, Halomonas, Rhodococcus, Bacillus, Acinetobacter, Pseudomonas, and Streptomyces were isolated. The first three genera were established after 1980s with interesting characteristics and limited relevant publications. Some of the 55 isolated strains were found with properties such as greatly reducing surface tension, stabilizing emulsion and producing flocculant. Isolates P6-4P and P1-5P were selected to demonstrate the performance of biosurfactant production, and were found to reduce the surface tension of water to as low as 28 dynes/cm. Copyright © 2014 Elsevier Ltd. All rights reserved.

Petroleum contamination of soil and water, and their effects on vegetables by statistically analyzing entire data set.

Science.gov (United States)

Zhang, Juan; Fan, Shu-kai; Yang, Jun-cheng; Du, Xiao-ming; Li, Fa-sheng; Hou, Hong

2014-04-01

Aliphatic hydrocarbons have been used to assess total oil concentrations, petroleum sources, and petroleum degradation. In this study, surface soil, groundwater, surface water, and vegetables were collected from the outskirts of Xi'an, the largest city in northwestern China, and the samples were analyzed for aliphatic hydrocarbon contents. The concentrations of n-alkanes were 1.06-4.01 μg/g in the soil. The concentrations and the geochemical characteristics of n-alkanes showed that the low carbon number hydrocarbons were mainly from petroleum sources, whereas the high carbon number hydrocarbons received more hydrocarbons from herbaceous plants. The concentrations of n-alkanes were 9.20-93.44 μg/L and 23.74-118.27 μg/L in the groundwater and the surface water, respectively. The water had characteristics of petroleum and submerged/floating macrophytes and was found in concentrations that would cause chronic disruption of sensitive organisms. The concentrations and geochemical characteristics of n-alkanes in Brassica chinensis L. and Apium graveolens were different, but both were contaminated by petroleum hydrocarbons. The results from principal component analysis (PCA) indicated that the sorption of n-alkanes to soil particles could not be described by linear models. The distributions of n-alkanes in vegetables were positively correlated with those in soil, and the correlation coefficient was up to 0.9310 using the constructed vectors. Therefore, the researchers should pay close attention to the effect of soil contamination on vegetables. Copyright © 2014 Elsevier B.V. All rights reserved.

Response of microalgae from mud-flats to petroleum hydrocarbons ...

African Journals Online (AJOL)

SERVER

2008-03-04

Mar 4, 2008 ... hydrocarbons in the presence of nitrogenous fertilizer ... the hydrocarbon, there was delayed nutrient uptake. ... waters, but the use of inorganic of organic nitrogen in ... ment, fish kills as oxygen is depleted, offensive odour.

Geochemical assessment of light gaseous hydrocarbons in near ...

Indian Academy of Sciences (India)

Light hydrocarbons in soil have been used as direct indicators in geochemical hydrocarbon exploration, which remains an unconventional path in the petroleum industry. The occurrence of adsorbed soil ... Kalpana1 D J Patil1 A M Dayal1. National Geophysical Research Institute, Uppal Road, Hyderabad 500606, India.

Hydrocarbon removal with constructed wetlands

OpenAIRE

Eke, Paul Emeka

2008-01-01

Wetlands have long played a significant role as natural purification systems, and have been effectively used to treat domestic, agricultural and industrial wastewater. However, very little is known about the biochemical processes involved, and the use of constructed treatment wetlands in the removal of petroleum aromatic hydrocarbons from produced and/or processed water. Wastewaters from the oil industry contain aromatic hydrocarbons such as benzene, toluene, ethylbenzene and x...

Petroleum Oxidation in Marine Microcosms by Natural Microbial Assemblages

Science.gov (United States)

Wardlaw, G. D.; Reddy, C. M.; Nelson, R. K.; Ehrhardt, C. J.; Valentine, D. L.

2006-12-01

Millions of gallons of petroleum are emitted into marine environments each year and the oxidation of this oil by microbes is an important mechanism for mediating toxicity. In terms of quantity, petroleum is the most abundant organic pollutant impacting marine environments today. Recent advances in chromatography have led to the development of comprehensive two-dimensional gas chromatography (GC &GC). The acronym, GC GC, is used because orthogonal gas chromatographic separations are achieved in both analytical dimensions by using stationary phases with varying partitioning abilities and selectivity. This novel method has greatly expanded the analytical window of petroleum hydrocarbons and was used to track the loss of petroleum hydrocarbons in aerobic marine microcosm experiments. Sediment microcosms were composed of seawater and sediment collected from the Coal Oil Point (COP) seep field off the coast of Santa Barbara, CA. Oil collected directly from the reservoir underlying the seep field was added to each microcosm, and samples were incubated for one year. Net metabolism was tracked by quantifying oxygen consumption and carbon dioxide production. The loss of petroleum components was tracked with GC GC, whereas the bacterial and archaeal community structures were tracked using T-RFLP. Results of these incubation studies will be presented.

Use of a multi-process phytoremediation system for decontamination of petroleum impacted soils : results of successful field trials

International Nuclear Information System (INIS)

Greenberg, B.M.; Gurska, J.; Huang, X.D.; Gerhardt, K.E.; Yu, X.M.; Nykamp, J.; MacNeill, G.; Yang, S.; Lu, X.; Glick, B.; Wang, W.; Knezevich, N.; Reid, N.

2008-01-01

The multi-process phytoremediation system (MPPS) was developed to degrade petroleum hydrocarbons (PHCs) in impacted soils. Phytoremediation of persistent contaminants in soils holds significant promise for rapid remediation kinetics. MPPS effectively removes polycyclic aromatic hydrocarbons (PAHs), total petroleum hydrocarbons (TPHs) and chlorinated hydrocarbons (CHCs) from soils. A plant growth promoting rhizobacteria interaction is the main element for success as it mitigates stress ethylene effects in plants, leading to high root biomass which, in turn, promotes growth of rhizosphere organisms. Field tests of the MPPS were initiated at a farm site in Sarnia, Ontario in the summer of 2004. The field was contaminated with petroleum hydrocarbons from refinery oil sludge. The second field trial was performed for 3 consecutive years at a petroleum contaminated biopile in Turner Valley, Alberta. The paper presented the results of the successful field tests of the MPPS. It was concluded that increased root biomass is achieved in the contaminated soils, which leads to more efficient and complete removal of TPHs in the field. Three years of field trials of the MPPS showed that remediation continues with successive seasons. 28 refs., 1 tab., 3 figs

Water Pollution and Treatments Part II: Utilization of Agricultural Wastes to Remove Petroleum Oils From Refineries Pollutants Present in Waste Water

International Nuclear Information System (INIS)

Ali, N.A.; El-Emary, M.M.

2011-01-01

Several natural agricultural wastes, of lignocellulose nature, such as Nile flower plant (ward El-Nil), milled green leaves, sugar cane wastes, palm tree leaves (carina), milled cotton stems, milled linseed stems, fine sawdust, coarse sawdust and palm tree cover were dried and then crushed to suitable size to be evaluated and utilized as adsorbents to remove oils floating or suspended in the waste water effluents from refineries and petroleum installations. The parameters investigated include effect of adsorbent type (adsorptive efficiency), adsorbate (type and concentration), mixing time, salinity of the water, adsorbent ratio to treated water, temperature, ph and stirring. Two different Egyptian crude oils varying in their properties and several refined products such as gasoline, kerosene, gas oil, diesel oil, fuel oil and lubricating oil were employed in this work in addition to the skimmed oil from the skim basin separator. Most of the agricultural wastes proved to be very effective in adsorbing oils from waste water effluents.

Condensation Mechanism of Hydrocarbon Field Formation.

Science.gov (United States)

Batalin, Oleg; Vafina, Nailya

2017-08-31

Petroleum geology explains how hydrocarbon fluids are generated, but there is a lack of understanding regarding how oil is expelled from source rocks and migrates to a reservoir. To clarify the process, the multi-layer Urengoy field in Western Siberia was investigated. Based on this example, we have identified an alternative mechanism of hydrocarbon field formation, in which oil and gas accumulations result from the phase separation of an upward hydrocarbon flow. There is evidence that the flow is generated by the gases released by secondary kerogen destruction. This study demonstrates that oil components are carried by the gas flow and that when the flow reaches a low-pressure zone, it condenses into a liquid with real oil properties. The transportation of oil components in the gas flow provides a natural explanation for the unresolved issues of petroleum geology concerning the migration process. The condensation mechanism can be considered as the main process of oil field formation.

Comparative bioremediation of heavy metals and petroleum hydrocarbons co-contaminated soil by natural attenuation, phytoremediation, bioaugmentation and bioaugmentation-assisted phytoremediation.

Science.gov (United States)

Agnello, A C; Bagard, M; van Hullebusch, E D; Esposito, G; Huguenot, D

2016-09-01

Biological remediation technologies are an environmentally friendly approach for the treatment of polluted soils. This study evaluated through a pot experiment four bioremediation strategies: a) natural attenuation, b) phytoremediation with alfalfa (Medicago sativa L.), c) bioaugmentation with Pseudomonas aeruginosa and d) bioaugmentation-assisted phytoremediation, for the treatment of a co-contaminated soil presenting moderate levels of heavy metals (Cu, Pb and Zn at 87, 100 and 110mgkg(-1) DW, respectively) and petroleum hydrocarbons (3800mgkg(-1) DW). As demonstrated by plant biomass and selected physiological parameters alfalfa plants were able to tolerate and grow in the co-contaminated soil, especially when soil was inoculated with P. aeruginosa, which promoted plant growth (56% and 105% increase for shoots and roots, respectively) and appeared to alleviate plant stress. The content of heavy metals in alfalfa plants was limited and followed the order: Zn>Cu>Pb. Heavy metals were mainly concentrated in plant roots and were poorly translocated, favouring their stabilization in the root zone. Bioaugmentation of planted soil with P. aeruginosa generally led to a decrease of plant metal concentration and translocation. The highest degree of total petroleum hydrocarbon removal was obtained for bioaugmentation-assisted phytoremediation treatment (68%), followed by bioaugmentation (59%), phytoremediation (47%) and natural attenuation (37%). The results of this study demonstrated that the combined use of plant and bacteria was the most advantageous option for the treatment of the present co-contaminated soil, as compared to natural attenuation, bioaugmentation or phytoremediation applied alone. Copyright © 2015 Elsevier B.V. All rights reserved.

Response of microbial community and catabolic genes to simulated petroleum hydrocarbon spills in soils/sediments from different geographic locations.

Science.gov (United States)

Liu, Q; Tang, J; Liu, X; Song, B; Zhen, M; Ashbolt, N J

2017-10-01

Study the response of microbial communities and selected petroleum hydrocarbon (PH)-degrading genes on simulated PH spills in soils/sediments from different geographic locations. A microcosm experiment was conducted by spiking mixtures of petroleum hydrocarbons (PHs) to soils/sediments collected from four different regions of China, including the Dagang Oilfield (DG), Sand of Bohai Sea (SS), Northeast China (NE) and Xiamen (XM). Changes in bacterial community and the abundance of PH-degrading genes (alkB, nah and phe) were analysed by denaturing gradient electrophoresis (DGGE) and qPCR, respectively. Degradation of alkanes and PAHs in SS and NE materials were greater (P < 0·05) than those in DG and XM. Clay content was negatively correlated with the degradation of total alkanes by 112 days and PAHs by 56 days, while total organic carbon content was negatively correlated with initial degradation of total alkanes as well as PAHs. Abundances of alkB, nah and phe genes increased 10- to 100-fold and varied by soil type over the incubation period. DGGE fingerprints identified the dominance of α-, β- and γ-Proteobacteria (Gram -ve) and Actinobacteria (Gram +ve) bacteria associated with degradation of PHs in the materials studied. The geographic divergence resulting from the heterogeneity of physicochemical properties of soils/sediments appeared to influence the abundance of metabolic genes and community structure of microbes capable of degrading PHs. When developing practical in-situ bioremediation approaches for PHs contamination of soils/sediment, appropriate microbial community structures and the abundance of PH-degrading genes appear to be influenced by geographic location. © 2017 The Society for Applied Microbiology.

Petroleum hydrocarbon concentrations in marine sediments along Nagapattinam - Pondicherry coastal waters, Southeast coast of India.

Science.gov (United States)

Kamalakannan, K; Balakrishnan, S; Sampathkumar, P

2017-04-15

In this present study, petroleum hydrocarbons were statistically analyzed in three different coastal sediment cores viz., (N1, P1 and P2) from the Southeast coast of Tamil Nadu, India to examine the viability of PHCs. The significant positive relationship between mud (silt+clay+sand) and PHC unveiled that high specific surface of area of mud content raise the level of PHCs. Cluster analysis was used to discriminate the sediment samples based on their degree of contamination. The present study shows that instead of expensive and destructive PHC chemical methods, magnetic susceptibility is found to be a suitable, cheap and rapid method for detailed study of PHC in marine sediments. This baseline PHCs data can be used for regular ecological monitoring and effective management for the mining and tourism related activities in the coastal ecosystem. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Process for the separation of light hydrocarbons, etc

Energy Technology Data Exchange (ETDEWEB)

1886-02-28

A process is described for producing by distillation under pressure (less than 2 atm.) from heavy, light, or dark paraffin oils (brown-coal tar oils), crude shale oil, and petroleum, from the residues remaining from the refining of crude petroleum, from the tar resulting from the manufacture of oil gases from paraffin oils or petroleum residues, and from all similar mineral oils light hydrocarbons and at the same time thick lubricating oil or asphaltlike oils.

The Use of Integrated Fluid Inclusion Studies for Constraining Petroleum Charge History at Parsons Pond, Western Newfoundland, Canada

Directory of Open Access Journals (Sweden)

James Conliffe

2017-03-01

Full Text Available This study, based on fluid inclusion petrography, microthermometry and ultraviolet microspectroscopy of inclusion oil, investigates the petroleum charge history at Parsons Pond, western Newfoundland. To address this matter, drill core and cuttings samples of allochthonous and autochthonous strata in the Parson’s Pond area were collected from three exploration wells. Fluid inclusions were examined from fragments of calcite and quartz veins, diagenetic cements in sandstone, and in large hydrothermal dolomite and calcite crystals. Primary aqueous inclusions in authigenic sandstone cements indicate that cementation occurred at relatively shallow depths and low temperatures (<50 °C. Hydrocarbon-bearing fluid inclusions (petroleum, wet gas and gas are generally restricted to calcite and quartz veins, indicating that petroleum and gas migration at Parson’s Pond is fracture-controlled. No hydrocarbons were observed in the diagenetic cements of the essentially tight sandstones. Fluid inclusion microthermometry and ultraviolet microspectroscopy indicate the presence of multiple generations of hydrocarbon fluid, ranging in composition from ~33 API gravity petroleum to pure CH4. Petrographic evidence suggests that hydrocarbons were generated multiple times during progressive burial and heating. In addition, the distribution of hydrocarbon bearing inclusions with depth suggests that deeper levels are gas-prone, with petroleum confined to relatively shallow depths. Although only gas flow was encountered during the drilling of exploration wells at Parson’s Pond, the presence of petroleum-bearing fluid inclusions in calcite and quartz veins indicates that the historical production from shallow wells in the Parsons Pond area likely tapped small reservoirs of fractured petroliferous strata.

China's petroleum industry

International Nuclear Information System (INIS)

Boykiw, A.; Katsuris, D.

1997-01-01

Petroleum and natural gas resources, industry organization, production, pipeline construction and other transportation issues, refining and business aspects of the Chinese petroleum and natural gas industries were reviewed. The need for large amounts of foreign capital and western technology to stem the deficit in domestic hydrocarbon supply were emphasized as being responsible for the creation in China of favourable conditions for foreign participation in oil and gas exploration, and for the growing confidence for Western investment in China. The most important considerations for successful participation in the economic development of China include: understanding the roles of networking, cultural affinity and reciprocity; hands-on management; finding an appropriate business partner, agent/distributor, or joint venture partner; and understanding local peculiarities and customs. 3 refs

The petroleum refining industry and the implications for the environment

International Nuclear Information System (INIS)

Saraiva, Gerardo Jose de Pontes

2000-01-01

The petroleum refining industry is basically concerned with the production of oil, lubricants and intermediate petrochemical products, utilizing crude oil as its main raw material. Petroleum refining, a distillation process that breaks hydrocarbons into fractions, eliminating undesired impurities, generates irreducible residues. Until the industrial revolution, the residues were essentially organic, susceptible to the attack of agents of destruction and transformation (bacterium, fungi, etc). Suddenly, due to the intensification of human activities of modern man, nature scattered across the planet more resistant products, many of them with long life times, that produce a deeper impact in the environment. Almost entirely marine is the pollution that results from increasing quantity of hydrocarbons dumped into the sea, a problem that is aggravated by the development of manufacturing and transportation of petroleum products. The expansion of the petroleum commerce, using essentially maritime transportation, has increased considerably the probability of accidents increasing the risks of environment pollution. This work presents suggestions and possible solutions to minimize the problem of environment pollution, caused by refining and transportation of this combustible, essential to present time industry. (author)

[Effects and Biological Response on Bioremediation of Petroleum Contaminated Soil].

Science.gov (United States)

Yang, Qian; Wu, Man-li; Nie, Mai-qian; Wang, Ting-ting; Zhang, Ming-hui

2015-05-01

Bioaugmentation and biostimulation were used to remediate petroleum-contaminated soil which were collected from Zichang city in North of Shaanxi. The optimal bioremediation method was obtained by determining the total petroleum hydrocarbon(TPH) using the infrared spectroscopy. During the bioremediation, number of degrading strains, TPH catabolic genes, and soil microbial community diversity were determined by Most Probable Number (MPN), polymerase chain reaction (PCR) combined agarose electrophoresis, and PCR-denaturing gradient electrophoresis (DGGE). The results in different treatments showed different biodegradation effects towards total petroleum hydrocarbon (TPH). Biostimulation by adding N and P to soils achieved the best degradation effects towards TPH, and the bioaugmentation was achieved by inoculating strain SZ-1 to soils. Further analysis indicated the positive correlation between catabolic genes and TPH removal efficiency. During the bioremediation, the number of TPH and alkanes degrading strains was higher than the number of aromatic degrading strains. The results of PCR-DGGE showed microbial inoculums could enhance microbial community functional diversity. These results contribute to understand the ecologically microbial effects during the bioremediation of petroleum-polluted soil.