WorldWideScience

Sample records for pesticide factory waltham

  1. Abatement of malodorants from pesticide factory in dielectric barrier discharges

    International Nuclear Information System (INIS)

    Chen Jie; Yang Jiantao; Pan Hua; Su Qingfa; Liu Yamin; Shi Yao

    2010-01-01

    Traditional odor control methods are limitative technically and economically for the abatement of odor from pesticide factory due to its toxicity and complicated composition. Non-thermal plasma (NTP) methods, typically characterized by high removal efficiency, energy yields and good economy, offer possible alternative solutions. This paper provides laboratory scale experimental data on the removal of simulated odors from pesticide factory with various humidity (0-0.8 vol%) and oxygen contents (0-21%) by a dielectric barrier discharge (DBD) reactor. Peak voltage and initial dimethylamine (DML) concentration are important factors that influence the DML removal efficiency and energy yield. The conversion of DML of 761 mg/m 3 reaches 100% at a peak voltage of 41.25 kV. Under the experiment conditions, the conversion of DML increases with an increase of oxygen contents. And the highest DML conversion was achieved with the gas stream containing 0.3% water. Simultaneously, the concentration of O 3 and OH radical in reactor was measured. Higher conversion, higher energy yield and fewer byproducts were found in mixed odor (DML + dimethyl sulfide (DMS)) treatment than that in single odor treatment. The energy yield is promoted from 2.13 to 5.20 mg/kJ.

  2. [Risk assessment and countermeasure of BTEX in pesticide factory].

    Science.gov (United States)

    Pang, Bo; Wang, Tie-Yu; Du, Li-Yu; Tan, Bing; Zhu, Zhao-Yun; Lu, Yong-Long

    2013-07-01

    BTEX are important environmental pollutants, harmful to human through respiratory inhalation, digestive tract and skin contact, and also have teratogenic, mutagenic and carcinogenic effects. BTEX were detected in multi-media to identify their distributions and assess their human health risk in a pesticide factory in Hebei province. Purge and trap GC-MS, adsorption/thermal desorption GC chromatography and the health risk assessment model were applied, and corresponding management measures were proposed. The results showed that BTEX existed in soil, dust, air, groundwater and wastewater. The concentration of BTEX in dust of the production area was 7.33 mg x kg(-1), in particular the concentration of toluene was 5.64 mg x kg(-1), exceeding the Canadian industrial land standard. Building three scenarios for working more than 10 years, 20 years and 30 years, the total non-carcinogens index was 4.19 x10(-3), 8.25 x 10(-3) and 1.22 x 10(-2), respectively, all lower than 1; the carcinogens index of benzene was 1.70 x 10(-7), 3.34 x 10(-7) and 4.92 x 10(-7), respectively, all lower than 10(-6). It indicated that there was no significant non-carcinogens and carcinogens hazard to workers inside the factory, but they might be exposed to more health risks if their work experience increase. Finally, recommendations for improving the environmental quality and personnel security in the factory were proposed based on the research results.

  3. Heavy metals and pesticide exposure from agricultural activities and former agrochemical factory in a Salvadoran rural community.

    Science.gov (United States)

    Quinteros, Edgar; Ribó, Alexandre; Mejía, Roberto; López, Alejandro; Belteton, Wilfredo; Comandari, Aimee; Orantes, Carlos M; Pleites, Ernesto B; Hernández, Carlos E; López, Dina L

    2017-01-01

    Pesticide handling in farming activities involves substantial hazards for the rural population and for the environment. In Latin America, it is estimated that the population at risk of being affected by heavy metals is over 4 million. This research describes the different types of exposure to pesticides and heavy metals in a rural population (Loma del Gallo), considering both environmental and occupational exposure. This study consists of an inspection in a former pesticide factory (QUIMAGRO), analysis of heavy metals in samples from surface and ground water in the community close to the factory, and a survey to the local population about their perceptions of pesticide exposures. Containers with 34.6 tons of chemicals improperly stored were identified in the former factory and removed by the government. Arsenic and cadmium were found in groundwater, and the highest values were 0.012 and 0.004 mg/l, respectively. These contaminants were also detected in most surface water samples, with maximum values of 0.026 and 0.0001 mg/l, respectively. Results of the survey show that of the 44 participants 42 % were farmers. Farmers used 19 different pesticide products containing 11 active ingredients. The most used active ingredients were paraquat (65 %), methamidophos (35 %), and atrazina (29 %). Eighty-two percent of the farmers did not use personal protective equipment. In addition to the pesticides used in the agriculture of the area, pesticide containers were removed from the QUIMAGRO area, but the pollution was still present at time of sampling and it is evident by the odor of the site. Surface water had the major concentration of heavy metals than the groundwater. Loma del Gallo population has been exposed to toxic pesticide from QUIMAGRO and agriculture for many years. The farmers carry out mishandling of pesticides and they not use PPE.

  4. [Pollution characteristics and health risk assessment of atmospheric volatile organic compounds (VOCs) in pesticide factory].

    Science.gov (United States)

    Tan, Bing; Wang, Tie-Yu; Pang, Bo; Zhu, Zhao-Yun; Wang, Dao-Han; Lü, Yong-Long

    2013-12-01

    A method for determining volatile organic compounds (VOCs) in air by summa canister collecting and gas chromatography/ mass spectroscopy detecting was adopted. Pollution condition and characteristics of VOCs were discussed in three representative pesticide factories in Zhangjiakou City, Hebei Province. Meanwhile, an internationally recognized four-step evaluation model of health risk assessment was applied to preliminarily assess the health risk caused by atmospheric VOCs in different exposure ways, inhalation and dermal exposure. Results showed that serious total VOCs pollution existed in all factories. Concentrations of n-hexane (6161.90-6910.00 microg x m(-3)), benzene (126.00-179.30 microg x m(-3)) and 1,3-butadiene (115.00-177.30 microg x m(-3)) exceeded the Chronic Inhalation Reference Concentrations recommended by USEPA, corresponding to 700, 30 and 2 microg x m(-3), respectively. Concentration of dichloromethane (724.00 microg x m(-3)) in factory B was also higher than the reference concentration (600 microg x m(-3)). Results of health risk assessment indicated that non-carcinogenic risk indexes of VOCs ranged from 1.00E-04 to 1.00E + 00 by inhalation exposure, and 1.00E-09 to 1.00E-05 by dermal exposure. Risk indexes of n-hexane and dichloromethane by inhalation exposure in all factories exceeded 1, and risk index of benzene by inhalation in factory B was also higher than 1. Carcinogenic risk indexes exposed to VOCs ranged from 1.00E-08 to 1.00E-03 by inhalation exposure and 1. oo00E -13 to 1.00E-08 by dermal exposure. Cancer risk of 1,3-butadiene by inhalation exceeded 1.0E-04, which lead to definite risk, and those of benzene by inhalation also exceeded the maximum allowable level recommended by International Commission on Radiological Protection (5.0E-05). The risks of dermal exposure presented the same trend as inhalation exposure, but the level was much lower than that of inhalation exposure. Thus, inhalation exposure of atmospheric VOCs was the

  5. [Risk assessment and countermeasures of BTEX contamination in soils of typical pesticide factory].

    Science.gov (United States)

    Tan, Bing; Wang, Tie-Yu; Li, Qi-Feng; Zhang, Hai-Yan; Pang, Bo; Zhu, Zhao-Yun; Wang, Dao-Han; Lü, Yong-Long

    2014-06-01

    Soil samples around three representative pesticide factories were collected in Zhangjiakou City, Hebei Province, and analyzed to identify their pollution characteristics and health risk of BTEX by purge-and trap and gas chromatography/mass spectroscopy method. Total concentrations of BTEX in soils in Plant A, B and C ranged from 673.50 to 32 363.50 ng x g(-1), nd to 6 461.80 ng x g(-1) and 461.70 to 8 740.80 ng x g(-1), respectively. Concentrations of detected toluene (4 619.50-7 234.30 ng x g(-1)) and ethylbenzene (364.60-7 944.60 ng x g(-1)) had exceeded the Canadian guidelines for industrial land (370 ng x g(-1) and 82 ng x g(-1)), and concentration of xylene (19 799.40 ng x g(-1)) in dust in production area of Plant A was larger than the Dutch soil intervention value (17 000 ng x g(-1)). While concentrationsn of BTEX around Plant A (Region I ) and Plant B and C (Region II) ranged from nd to 645.81 ng x g(-1), and nd to 309.13 ng x g(-1), respectively, which were below the Canadian guidelines for agricultural land. The non-carcinogenic risk of BTEX in Plant A (2.90E-06 -1.32E-04), B (nd -4.30E-05) and C (1.29E-06 -5.64E-05) were all below 1, which suggested that no obvious health risk existed in each plant. The non-carcinogenic risks in Region I (nd -2.02E-06) and Region II (nd -1.10E-06) were below than 1, and also lower than those in factories. High risk areas were mainly concentrated in the downwind, moreover, soils around villages and towns were also with higher risk. In conclusion, soils and dusts in each factory had been polluted and the quality of agricultural land had been partly deteriorated. Finally, environmental management and occupational protection countermeasures were proposed based on the research results.

  6. Pesticides

    Science.gov (United States)

    ... stores. Exposure to pesticides can happen in the workplace, through foods that are eaten, and in the ... or place bait in areas where children or pets have access. DO NOT stock up on pesticides, ...

  7. Multivariate study of parameters in the determination of pesticide residues in apple by headspace solid phase microextraction coupled to gas chromatography-mass spectrometry using experimental factorial design.

    Science.gov (United States)

    Abdulra'uf, Lukman Bola; Tan, Guan Huat

    2013-12-15

    Solid-phase microextraction (SPME) is a solvent-less sample preparation method which combines sample preparation, isolation, concentration and enrichment into one step. In this study, multivariate strategy was used to determine the significance of the factors affecting the solid phase microextraction of pesticide residues (fenobucarb, diazinon, chlorothalonil and chlorpyrifos) using a randomised factorial design. The interactions and effects of temperature, time and salt addition on the efficiency of the extraction of the pesticide residues were evaluated using 2(3) factorial designs. The analytes were extracted with 100 μm PDMS fibres according to the factorial design matrix and desorbed into a gas chromatography-mass spectrometry detector. The developed method was applied for the analysis of apple samples and the limits of detection were between 0.01 and 0.2 μg kg(-)(1), which were lower than the MRLs for apples. The relative standard deviations (RSD) were between 0.1% and 13.37% with average recovery of 80-105%. The linearity ranges from 0.5-50 μg kg(-)(1) with correlation coefficient greater than 0.99. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Particle factories

    International Nuclear Information System (INIS)

    Schindler, Rafe

    1989-01-01

    Physicists' attention is increasingly turning to the high luminosity frontier - providing enough collisions to amass sizable numbers of rare events - to complement the traditional quest for higher energies. This month we cover three areas where projects are now being considered: Phi-factory workshop, PSI Planning for B meson factory, Tau-charm factory

  9. Particle factories

    Energy Technology Data Exchange (ETDEWEB)

    Schindler, Rafe

    1989-07-15

    Physicists' attention is increasingly turning to the high luminosity frontier - providing enough collisions to amass sizable numbers of rare events - to complement the traditional quest for higher energies. This month we cover three areas where projects are now being considered: Phi-factory workshop, PSI Planning for B meson factory, Tau-charm factory.

  10. Internet Factories

    NARCIS (Netherlands)

    Strijkers, R.J.

    2014-01-01

    This thesis contributes a novel concept for introducing new network technologies in network infrastructures. The concept, called Internet factories, describes the methodical process to create and manage application-specific networks from application programs, referred to as Netapps. An Internet

  11. Internet factories

    NARCIS (Netherlands)

    Strijkers, R.J.

    2014-01-01

    This thesis contributes a novel concept for introducing new network technologies in network infrastructures. The concept, called Internet factories, describes the methodical process to create and manage application-specific networks from application programs, referred to as Netapps. An Internet

  12. Factory physics

    CERN Document Server

    Hopp, Wallace J.

    2011-01-01

    After a brief introductory chapter, "Factory Physics 3/e" is divided into three parts: I - The Lessons of History; II - Factory Physics; and III - Principles in Practice. The scientific approach to manufacturing and supply chain management, developed in Part II, is unique to this text. No other text or professional book provides a rigorous, principles-based foundation for manufacturing management. The Third Edition offers tighter connections between Lean Manufacturing, MRP/ERP, Six Sigma, Supply Chain Management, and Factory Physics. In addition to enhancing the historical overview of how these systems evolved, the authors show explicitly how users can achieve Lean Manufacturing objectives (faster response, less inventory) using the integration aspects of MRP/ERP/SCM systems along with the variance analysis methods of Six Sigma. Factory Physics provides the overarching framework that coordinates all of these initiatives into a single-focused strategy.

  13. Baby Factory

    African Journals Online (AJOL)

    Prof

    2018-01-24

    Jan 24, 2018 ... mass media have the power to easily propagate ideas on social change ... issue of 'baby factory' is becoming everyday news affecting the right of ... according to recent mass media reports, teenage girls and young women are.

  14. Neutrino Factory

    CERN Document Server

    Bogomilov, M; Tsenov, R; Dracos, M; Bonesini, M; Palladino, V; Tortora, L; Mori, Y; Planche, T; Lagrange, J  B; Kuno, Y; Benedetto, E; Efthymiopoulos, I; Garoby, R; Gilardoini, S; Martini, M; Wildner, E; Prior, G; Blondel, A; Karadzhow, Y; Ellis, M; Kyberd, P; Bayes, R; Laing, A; Soler, F  J  P; Alekou, A; Apollonio, M; Aslaninejad, M; Bontoiu, C; Jenner, L  J; Kurup, A; Long, K; Pasternak, J; Zarrebini, A; Poslimski, J; Blackmore, V; Cobb, J; Tunnell, C; Andreopoulos, C; Bennett, J  R  J; Brooks, S; Caretta, O; Davenne, T; Densham, C; Edgecock, T  R; Fitton, M; Kelliher, D; Loveridge, P; McFarland, A; Machida, S; Prior, C; Rees, G; Rogers, C; Rooney, M; Thomason, J; Wilcox, D; Booth, C; Skoro, G; Back, J  J; Harrison, P; Berg, J  S; Fernow, R; Gallardo, J  C; Gupta, R; Kirk, H; Simos, N; Stratakis, D; Souchlas, N; Witte, H; Bross, A; Geer, S; Johnstone, C; Mokhov, N; Neuffer, D; Popovic, M; Strait, J; Striganov, S; Morfín, J  G; Wands, R; Snopok, P; Bogacz, S  A; Morozov, V; Roblin, Y; Cline, D; Ding, X; Bromberg, C; Hart, T; Abrams, R  J; Ankenbrandt, C  M; Beard, K  B; Cummings, M  A  C; Flanagan, G; Johnson, R  P; Roberts, T  J; Yoshikawa, C  Y; Graves, V  B; McDonald, K  T; Coney, L; Hanson, G

    2014-01-01

    The properties of the neutrino provide a unique window on physics beyond that described by the standard model. The study of subleading effects in neutrino oscillations, and the race to discover CP-invariance violation in the lepton sector, has begun with the recent discovery that $\\theta_{13} > 0$. The measured value of $\\theta_{13}$ is large, emphasizing the need for a facility at which the systematic uncertainties can be reduced to the percent level. The neutrino factory, in which intense neutrino beams are produced from the decay of muons, has been shown to outperform all realistic alternatives and to be capable of making measurements of the requisite precision. Its unique discovery potential arises from the fact that only at the neutrino factory is it practical to produce high-energy electron (anti)neutrino beams of the required intensity. This paper presents the conceptual design of the neutrino factory accelerator facility developed by the European Commission Framework Programme 7 EURO$\

  15. Phi factories

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    Plans for 'phi factories' gathered momentum with a recent workshop at UCLA. These machines, high luminosity electron-positron colliders working near the phi resonance at 1020 MeV, have been proposed at Laboratories in Europe, the US, Japan and the USSR

  16. Smart Factory

    DEFF Research Database (Denmark)

    Bilberg, Arne; Radziwon, Agnieszka; Grube Hansen, David

    2017-01-01

    their innovation and competitive advantage by focusing at their competences, strengths and opportunities. The project suggests innovative solutions and business models through collaboration and use of new technologies. In the Smart Factory, SMEs should be able to collaborate on new products, markets and production......, and to target their challenges and ensure sustainable growth and business in these enterprises. Therefore the focus of the Smart Factory project was to support the growth and sustainable development of the small and medium sized manufacturing industry in Denmark. The project focused on SMEs and how to improve......A large part of Danish Industry is based on Small and Medium Sized Enterprises (SMEs), which account for –99% of the companies in Denmark and about two third of the job positions (source: statistikbanken.dk) . That is why, it is so important also to focus research and development at SMEs...

  17. Neutrino factories

    International Nuclear Information System (INIS)

    Dydak, F.

    2002-01-01

    The discovery of neutrino oscillations marks a major milestone in the history of neutrino physics, and opens a window to what lies beyond the Standard Model. Many current and forthcoming experiments will answer open questions; however, a major step forward, up to and possibly including CP violation in the neutrino mixing matrix, will be offered by the neutrino beams from a neutrino factory. The neutrino factory is a new concept for producing neutrino beams of unprecedented quality in terms of intensity, flavour composition, and precision of the beam parameters. These beams enable the exploration of otherwise inaccessible domains in neutrino oscillation physics by exploiting baselines of planetary dimensions. Suitable detectors pose formidable challenges but seem within reach with only moderate extrapolations from existing technologies. Although the main physics attraction of the neutrino factory is in the area of neutrino oscillations, an interesting spectrum of further opportunities ranging from high-precision, high-rate neutrino scattering to physics with high-intensity stopped muons comes with it

  18. Meson factories

    International Nuclear Information System (INIS)

    Dicello, J.F.; Zaider, M.; Bradbury, J.N.

    1979-01-01

    Technological improvements in accelerator design in the 1960's resulted in the capability to develop medium-energy proton accelerators with beam intensities of almost 1 mA. These beams are able to produce fluxes of secondary particles, including pions, muons, neutrinos, and neutrons, which are as much as 10,000 times as intense as those previously available. Those machines built for optimum meson production are commonly called meson factories. The characteristics of these facilities are reviewed, and the present programs in applied research, and some potential areas of future work are discussed

  19. Kaon factories

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1983-03-01

    Kaon factories would provide beams 100-1000 times more intense than those available from present accelerators in the 10-30 GeV range. More intense or cleaner secondary beams of kaons, antiprotons and neutrinos would be of particular interest for high precision experiments and studies of rare processes in both particle and nuclear physics, e.g. symmetry violations in K-decay, neutrino scattering, meson and baryon spectroscopy, hypernuclei, exotic atoms, K + studies of nuclear density and resonance propagation in nuclei. The various accelerators proposed include both fast-cycling synchrotrons providing 100 μA proton beams at 15 to 32 GeV and superconducting isochronous ring cyclotrons giving 100-400 μA at up to 15 GeV. This paper describes these designs and the various technical problems associated with them

  20. KAON factories

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1989-09-01

    Proposals for high intensity proton synchrotrons (typically providing 100 μA (6 x 10 14 p/s)) at 30 GeV have been made in Canada, Europe, Japan, the USA and the USSR. These beams would be roughly 100 times more intense than those available now and would yield equivalent increases in the fluxes of secondary particles (kaons, pions, muons, antiprotons, hyperons and neutrinos) - or cleaner beams for a smaller increase in flux. The ability to investigate rare processes on the precision frontier opens new avenues to fundamental questions in both particle and nuclear physics, complementary to traditional approaches via the energy frontier. The demand for higher currents has led to novel features in many of the accelerator designs: asymmetric magnet cycles, avoidance of transition crossing, separate collector and stretcher rings, three-dimensional beam painting at injection, bucket-to-bucket beam transfer, perpendicular biassing of microwave ferrite in the rf tuners, the use of Siberian Snakes to preserve polarization, and the addition of a pre-septum to make slow extraction >99.8% efficient. Other characteristic features include rapid cycling rates, booster stages, H - injection, low impedance enclosures, powerful feedback systems for control of beam instabilities and beam loading, and local collimation systems for handling beam loss. This paper reviews the general features of kaon factory accelerator design and the status of the various proposals

  1. Pesticide Labels

    Science.gov (United States)

    Pesticide labels translate results of our extensive evaluations of pesticide products into conditions, directions and precautions that define parameters for use of a pesticide with the goal of ensuring protection of human health and the environment.

  2. Antimicrobial Pesticides

    Science.gov (United States)

    EPA regulates pesticides under the statutory authority of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA). The registration requirements for antimicrobial pesticides differ somewhat from those of other pesticides. Find out more.

  3. Fractional factorial plans

    CERN Document Server

    Dey, Aloke

    2009-01-01

    A one-stop reference to fractional factorials and related orthogonal arrays.Presenting one of the most dynamic areas of statistical research, this book offers a systematic, rigorous, and up-to-date treatment of fractional factorial designs and related combinatorial mathematics. Leading statisticians Aloke Dey and Rahul Mukerjee consolidate vast amounts of material from the professional literature--expertly weaving fractional replication, orthogonal arrays, and optimality aspects. They develop the basic theory of fractional factorials using the calculus of factorial arrangements, thereby providing a unified approach to the study of fractional factorial plans. An indispensable guide for statisticians in research and industry as well as for graduate students, Fractional Factorial Plans features: * Construction procedures of symmetric and asymmetric orthogonal arrays. * Many up-to-date research results on nonexistence. * A chapter on optimal fractional factorials not based on orthogonal arrays. * Trend-free plans...

  4. Cell Factory Engineering

    DEFF Research Database (Denmark)

    Davy, Anne Mathilde; Kildegaard, Helene Faustrup; Andersen, Mikael Rørdam

    2017-01-01

    focused on individual strategies or cell types, but collectively they fall under the broad umbrella of a growing field known as cell factory engineering. Here we condense >130 reviews and key studies in the art into a meta-review of cell factory engineering. We identified 33 generic strategies......-review provides general strategy guides for the broad range of applications of rational engineering of cell factories....

  5. PCs in the factory

    CERN Document Server

    2013-01-01

    Please note this is a short discount publication.PCs have become as essential to the factory environment as they are to the office environment. This in-depth report examines how specially adapted PCs and peripherals are being established in Factory Process Control and Reporting. The report covers: * Hardware and Software* Typical Applications* Implementation Issues* Case Studies and Real Applications

  6. Towards energy transparent factories

    CERN Document Server

    Posselt, Gerrit

    2016-01-01

    This monograph provides a methodological approach for establishing demand-oriented levels of energy transparency of factories. The author presents a systematic indication of energy drivers and cost factors, taking into account the interdependencies between facility and production domains. Particular attention is given to energy flow metering and monitoring. Readers will also be provided with an in-depth description of a planning tool which allows for systematically deriving suitable metering points in complex factory environments. The target audience primarily comprises researchers and experts in the field of factory planning, but the book may also be beneficial for graduate students.

  7. Planned Positron Factory project

    International Nuclear Information System (INIS)

    Okada, Sohei

    1990-01-01

    The Japan Atomic Energy Research Institute, JAERI, has started, drafting a construction plan for the 'Positron Factory', in which intense energy-controllable monoenergetic positron beams are produced from pair-production reactions caused by high-energy electrons from a linac. The JAERI organized a planning committee to provide a basic picture for the Positron Factory. This article presents an overview of the interactions of positrons, intense positron sources and the research program and facilities planned for the project. The interactions of positrons and intense positron sources are discussed focusing on major characteristics of positrons in different energy ranges. The research program for the Positron Factory is then outlined, focusing on advanced positron annihilation techniques, positron spectroscopy (diffraction, scattering, channeling, microscopy), basic positron physics (exotic particle science), and positron beam technology. Discussion is also made of facilities required for the Positron Factory. (N.K.)

  8. Virtual Factory Testbed

    Data.gov (United States)

    Federal Laboratory Consortium — The Virtual Factory Testbed (VFT) is comprised of three physical facilities linked by a standalone network (VFNet). The three facilities are the Smart and Wireless...

  9. TRIUMF kaon factory plans

    International Nuclear Information System (INIS)

    Blackmore, E.W.

    1983-01-01

    A progress report on the TRIUMF Kaon Factory Feasibility Study is presented. The requirements placed on the machine parameters and experimental facilities by the potentially interesting experiments are discussed

  10. TRIUMF kaon factory plans

    International Nuclear Information System (INIS)

    Blackmore, E.W.

    1982-11-01

    A progress report on the TRIUMF Kaon Factory Feasibility Study is presented. The requirements placed on the machine parameters and experimental facilities by the potentially interesting experiments are discussed

  11. Super B Factories

    Indian Academy of Sciences (India)

    B factory; CP violation; B meson; supersymmetry. PACS Nos 11.30.Hv; 11.30.Pb; 12.15.Hh; 12.15.Mm; 13.20.He; 13.20.Fc;. 13.35.Dx; 14.65.Fy. 1. Introduction. The two asymmetric B factories, PEP-II and KEK-B, and their companion detec- tors, BABAR and Belle, have produced a wealth of flavor physics results, subjecting.

  12. Pesticide Reevaluation

    Science.gov (United States)

    Learn about the process for periodically evaluating registered pesticides to ensure they meet current science standards for risk assessment, as required by the Federal Insecticide Fungicide and Rodenticide Act.

  13. Tau-charm factory..

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1995-10-15

    In addition to hearing the latest experimental and theoretical developments at the 17th International Symposium on Lepton Photon Interactions in Beijing, delegates were brought up-to-date on the substantial progress towards the realization of a Tau-Charm Factory in the Chinese capital. Opening the Symposium, Zhou Guangzhao, President of the Chinese Academy of Sciences, expressed a commitment of the Chinese government to basic research and its interest in the continuing development high energy physics in China. Following the very successful construction and operation of Beijing's Electron-Positron Collider, BEPC, the Chinese government has provided 5M yuan ($US 600,000) for a feasibility study by the end of 1996 for a Tau-Charm Factory at Beijing's Institute of High Energy Physics (IHEP). Professor Zhou expressed his belief that, once approved, such a factory would greatly enhance high energy physics in China. He warmly welcomed international collaboration both in the construction of the accelerator and in the experimental programme. His comments were reinforced in the following welcome speech by IHEP Director Zheng Zhipeng. Conference delegates had the opportunity to inspect the BEPC injector and collider, built almost entirely by Chinese industry. The International Committee for Future Accelerators (ICFA) met during the Symposium, with Tau- Charm Factory business on the agenda. In his subsequent report, ICFA Chairman John Peoples said that a Tau-Charm Factory provides a unique experimental environment for the precision studies of tau, charm and light quark-gluon spectroscopy, and that some issues in these fields are not satisfactorily addressed solely by B Factories or fixed-target experiments. The committee expressed a strong interest in seeing a Tau-Charm Factory built and noted the serious interest, especially in China, and looks forward to operation and exploitation by the international physics community. In their Beijing summary talks, both Sam Ting and T

  14. Tau-charm factory..

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    In addition to hearing the latest experimental and theoretical developments at the 17th International Symposium on Lepton Photon Interactions in Beijing, delegates were brought up-to-date on the substantial progress towards the realization of a Tau-Charm Factory in the Chinese capital. Opening the Symposium, Zhou Guangzhao, President of the Chinese Academy of Sciences, expressed a commitment of the Chinese government to basic research and its interest in the continuing development high energy physics in China. Following the very successful construction and operation of Beijing's Electron-Positron Collider, BEPC, the Chinese government has provided 5M yuan ($US 600,000) for a feasibility study by the end of 1996 for a Tau-Charm Factory at Beijing's Institute of High Energy Physics (IHEP). Professor Zhou expressed his belief that, once approved, such a factory would greatly enhance high energy physics in China. He warmly welcomed international collaboration both in the construction of the accelerator and in the experimental programme. His comments were reinforced in the following welcome speech by IHEP Director Zheng Zhipeng. Conference delegates had the opportunity to inspect the BEPC injector and collider, built almost entirely by Chinese industry. The International Committee for Future Accelerators (ICFA) met during the Symposium, with Tau- Charm Factory business on the agenda. In his subsequent report, ICFA Chairman John Peoples said that a Tau-Charm Factory provides a unique experimental environment for the precision studies of tau, charm and light quark-gluon spectroscopy, and that some issues in these fields are not satisfactorily addressed solely by B Factories or fixed-target experiments. The committee expressed a strong interest in seeing a Tau-Charm Factory built and noted the serious interest, especially in China, and looks forward to operation and exploitation by the international physics community. In their Beijing summary talks, both Sam Ting

  15. Colorful Microbial Cell Factories

    DEFF Research Database (Denmark)

    Petersen, Pia Damm

    Yeast cell factories are powerful tools used for the production of high-value natural compounds otherwise not easily available. Many bioactive and industrially important plant secondary metabolites can be produced in yeast by engineering their biosynthetic pathways into yeast cells, as these both...... anthocyanins. Yeast cell factories present a platform to circumvent the problem of low yields of interesting molecular structures in plant tissues, as hand-picking of desired enzyme activities allows for specific biosynthesis of the precise pigment of interest, as well as choosing more stable structures...... for heterologous biosynthesis is possible. In cell factories, great improvements in yields can be achieved through molecular engineering of flux from endogenous yeast precursors, e.g. by elimination of by-product formation, and by genetic optimization of pathway components, such as fine-tuning of expression levels...

  16. The Smart Factory

    DEFF Research Database (Denmark)

    Radziwon, Agnieszka; Bilberg, Arne; Bogers, Marcel

    2014-01-01

    Nowadays we live in a world, which a decade ago would only be described in the science fiction literature. More and more things become smart and both scientists and engineers strive for developing not only new and innovative devices, but also homes, factories, or even cities. Despite of continuous...... development, many of those concepts are still being just a vision of the future, which still needs a lot of effort to become true. This paper reviews the usage of adjective smart in respect to technology and with a special emphasis on the smart factory concept placement among contemporary studies. Due...... to a lack of a consensus of common understanding of this term, a unified definition is proposed. The conceptualization will not only refer to various smart factory visions reported in the literature, but also link the crucial characteristics of this emerging manufacturing concept to usual manufacturing...

  17. B-factory detectors

    International Nuclear Information System (INIS)

    Marlow, D.R.

    2002-01-01

    The designs of the recently commissioned BaBar and Belle B-Factory detectors are described. The discussion is organized around the methods and instruments used to detect the so-called gold-plated-mode B 0 →J/ΨK S decays and related modes

  18. Factorial Analysis of Profitability

    OpenAIRE

    Georgeta VINTILA; Ilie GHEORGHE; Ioana Mihaela POCAN; Madalina Gabriela ANGHEL

    2012-01-01

    The DuPont analysis system is based on decomposing the profitability ratio in factors of influence. This paper describes the factorial analysis of profitability based on the DuPont system. Significant importance is given to the impact on various indicators on the shares value and profitability.

  19. The Clone Factory

    Science.gov (United States)

    Stoddard, Beryl

    2005-01-01

    Have humans been cloned? Is it possible? Immediate interest is sparked when students are asked these questions. In response to their curiosity, the clone factory activity was developed to help them understand the process of cloning. In this activity, students reenact the cloning process, in a very simplified simulation. After completing the…

  20. Four-legged factories

    International Nuclear Information System (INIS)

    Mackie, R.I.; Van der Walt, J.G.

    1982-01-01

    Insight into how ruminants utilise plant material, converting what is essentially waste into food, wool and draught power for Man is being sought by Animal Scientists using isotopic tracer techniques. Answers to cost-effectice biological conversion lie in the complex interactions of the rumen's microbial fermentation factory and the host animal's diet and metabolism

  1. Haiti. Educating factory workers.

    Science.gov (United States)

    Hughes, H

    1990-04-01

    There are approximately 50,000 workers employed in the light assembly industry in Haiti. About 70% are women, the majority of whom are aged between 25 and 34 years, and are either single or in a nonpermanent relationship with the father of their children. Many live and work in appalling conditions, surviving on very low wages to support several children and an extended family. The acquired immunodeficiency syndrome (AIDS) is now a visible problem in many factories. In October 1988, the Center for the Promotion of Women Workers (Centre de Promotion des Femmes Ouvriers/CPFO) launched a pilot AIDS education program for factory women. The Center, based in a large industrial zone near the airport, runs a health clinic and courses in literacy, communications skills, health promotion and family planning. The new AIDS program allowed CPFO staff to gain entry into factories for the 1st time. Other courses were held outside working hours and outside factory premises. Staff contacted manages by telephone to arrange a meeting to discuss AIDS and to ask permission to hold educational "round tables" with workers. Of 18 managers in the factories approached over a 12-month period, only 2 refused entry to CPFO staff. Almost all managers reported they had registered between 2 and 5 deaths from AIDS among their employees over the past couple of years. A total of 85 educational sessions, each lasting about 2 hours, were held within 28 different factories, community or labor organizations reaching 3063 workers (male and female). In each session, the presentation was carried out by 2 CPFO trained monitors and included a slide show, flip charts, and the video "Met ko," originally produced for Haitian immigrants in New York. The most important aspect of the program was the training of 38 volunteer factory-based health promoters. These promoters attended the round table sessions, where they facilitated discussion and distributed condoms and were subsequently available for counseling co

  2. Food-Energy Interactive Tradeoff Analysis of Sustainable Urban Plant Factory Production Systems

    Directory of Open Access Journals (Sweden)

    Li-Chun Huang

    2018-02-01

    Full Text Available This research aims to analyze the food–energy interactive nexus of sustainable urban plant factory systems. Plant factory systems grow agricultural products within artificially controlled growing environment and multi-layer vertical growing systems. The system controls the supply of light, temperature, humidity, nutrition, water, and carbon dioxide for growing plants. Plant factories are able to produce consistent and high-quality agricultural products within less production space for urban areas. The production systems use less labor, pesticide, water, and nutrition. However, food production of plant factories has many challenges including higher energy demand, energy costs, and installation costs of artificially controlled technologies. In the research, stochastic optimization model and linear complementarity models are formulated to conduct optimal and equilibrium food–energy analysis of plant factory production. A case study of plant factories in the Taiwanese market is presented.

  3. Virtual Learning Factory on VR-Supported Factory Planning

    OpenAIRE

    Weidig , Christian; Menck , Nicole; Winkes , Pascal ,; Aurich , Jan ,

    2014-01-01

    Part 13: Virtual Reality and Simulation; International audience; Learning Factories are becoming popular as tangible measures to teach engineering methods while making use of them in an industrial-like environment. Their core component is usually a factory demonstrator, users are physically working with. For factory planning such approaches can hardly be adapted, due to long lasting realization phases.To overcome this obstacle a virtual learning factory has been developed whose core component...

  4. Review of kaon factory proposals

    International Nuclear Information System (INIS)

    Thiessen, H.A.

    1985-01-01

    Nuclear physics issues and particle physics issues for a kaon factory are discussed. Kaon factory accelerator proposals are then considered. Secondary beam considerations are covered and hardware development for a kaon factory is discussed. The prospects for construction are presented. 9 refs., 12 figs., 2 tabs

  5. Superconducting cavities for beauty factories

    International Nuclear Information System (INIS)

    Lengeler, H.

    1992-01-01

    The possibilities and merits of superconducting accelerating cavities for Beauty-factories are considered. There exist already large sc systems of size and frequency comparable to the ones needed for Beauty-factories. Their status and operation experience is discussed. A comparison of normal conducting and superconducting systems is done for two typical Beauty-factory rings

  6. Hazardous factories: Nigerian evidence.

    Science.gov (United States)

    Oloyede, Olajide

    2005-06-01

    The past 15 years have seen an increasing governmental and corporate concern for the environment worldwide. For governments, information about the environmental performance of the industrial sector is required to inform macro-level decisions about environmental targets such as those required to meet UN directives. However, in many African, Asian, and Latin American countries, researching and reporting company environmental performance is limited. This article serves as a contribution to filling the gap by presenting evidence of physical and chemical risk in Nigerian factories. One hundred and three factories with a total of 5,021 workers were studied. One hundred and twenty physical and chemical hazards were identified and the result shows a high number of workers exposed to such hazards. The study also reveals that workers' awareness level of chemical hazards was high. Yet the danger was perceived in behavioral terms, especially by manufacturing firms, which tend to see environmental investment in an increasingly global economy as detrimental to profitability.

  7. Engineering the smart factory

    Science.gov (United States)

    Harrison, Robert; Vera, Daniel; Ahmad, Bilal

    2016-10-01

    The fourth industrial revolution promises to create what has been called the smart factory. The vision is that within such modular structured smart factories, cyber-physical systems monitor physical processes, create a virtual copy of the physical world and make decentralised decisions. This paper provides a view of this initiative from an automation systems perspective. In this context it considers how future automation systems might be effectively configured and supported through their lifecycles and how integration, application modelling, visualisation and reuse of such systems might be best achieved. The paper briefly describes limitations in current engineering methods, and new emerging approaches including the cyber physical systems (CPS) engineering tools being developed by the automation systems group (ASG) at Warwick Manufacturing Group, University of Warwick, UK.

  8. Pesticides and the Environment

    Science.gov (United States)

    ; Environment Human Health Animal Health Safe Use Practices Food Safety Environment Air Water Soil Wildlife Home Page Pesticides and the Environment Related Topics: What Happens to Pesticides Released into the Environment? Pesticide Storage Pesticide Disposal Pesticide Products Integrated Pest Management (IPM) How Safe

  9. The TRIUMF KAON Factory

    International Nuclear Information System (INIS)

    Craddock, M.

    1989-05-01

    TRIUMF has been awarded $11M for a one-year pre-construction Engineering Design and Impact Study of the KAON Factory. This will enable prototypes of many accelerator components to be built and the design of the accelerators and the layout of the experimental areas to be reviewed. The building and tunnel designs will be finalized, environmental, legal and economic impact studies carried out, and international involvement pursued further

  10. Automation in the factory

    Energy Technology Data Exchange (ETDEWEB)

    Hatvany, J

    1984-05-01

    There are now about 100000 computers in the manufacturing plants of the world, but the thirty-year old dream of the computer-controlled factory is only now beginning to materialize. With the advent of advanced microprocessor technology of distributed systems based on local area networking and of supervisory and diagnostic systems utilizing artificial intelligence techniques, computer-integrated manufacturing (CIM) has today become a realistic aim. 6 references.

  11. SLAC B Factory computing

    International Nuclear Information System (INIS)

    Kunz, P.F.

    1992-02-01

    As part of the research and development program in preparation for a possible B Factory at SLAC, a group has been studying various aspects of HEP computing. In particular, the group is investigating the use of UNIX for all computing, from data acquisition, through analysis, and word processing. A summary of some of the results of this study will be given, along with some personal opinions on these topics

  12. Safe Disposal of Pesticides

    Science.gov (United States)

    ... Toxics Environmental Information by Location Greener Living Health Land, Waste, and Cleanup Lead Mold Pesticides Radon Science ... or www.earth911.com . Think before disposing of extra pesticides and containers: Never reuse empty pesticide containers. ...

  13. Endangered Species: Pesticide Restrictions

    Science.gov (United States)

    Our goal is to protect threatened and endangered species and their habitats, without placing unnecessary burden on agriculture and pesticide users. Pesticide limitations are developed to ensure safe use of pesticides in order to meet this goal.

  14. TRIUMF: Kaon factory physics

    International Nuclear Information System (INIS)

    Anon.

    1982-01-01

    The second TRIUMF Kaon Factory Physics Workshop was held on 10-14 August, 1981. About a hundred physicists participated in the meeting, which consisted of fifteen invited talks and four afternoon workshop sessions, and proved to be a stimulating and productive event. The discussions centred on identifying the most important physics that could be studied with a machine providing an increase in intensity of two orders of magnitude in primary proton beam over present accelerators in the energy range 8 to 20 GeV, and on establishing some preliminary guidelines on the desirable properties of secondary beams at such a machine

  15. KEK: B factory plans

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    To boost the study of B mesons (carrying the heavy b quark), the Japanese KEK Laboratory is looking to construct a B-meson 'factory'. B-mesons have revealed unexpected and important quark physics. Well-known examples are the long lifetime of the B-mesons, indicating a large gap between the third and second quark generation (compared to that between the second and the first), and relatively large mixing of the neutral B-meson and its antiparticle, now interpreted as being due to a heavy sixth ('top') quark

  16. Deciding WQO for factorial languages

    KAUST Repository

    Atminas, Aistis; Lozin, Vadim V.; Moshkov, Mikhail

    2013-01-01

    A language is factorial if it is closed under taking factors (i.e. contiguous subwords). Every factorial language can be described by an antidictionary, i.e. a minimal set of forbidden factors. We show that the problem of deciding whether a factorial language given by a finite antidictionary is well-quasi-ordered under the factor containment relation can be solved in polynomial time. © 2013 Springer-Verlag Berlin Heidelberg.

  17. Deciding WQO for factorial languages

    KAUST Repository

    Atminas, Aistis

    2013-04-05

    A language is factorial if it is closed under taking factors (i.e. contiguous subwords). Every factorial language can be described by an antidictionary, i.e. a minimal set of forbidden factors. We show that the problem of deciding whether a factorial language given by a finite antidictionary is well-quasi-ordered under the factor containment relation can be solved in polynomial time. © 2013 Springer-Verlag Berlin Heidelberg.

  18. Water and Pesticides

    Science.gov (United States)

    ; Environment Human Health Animal Health Safe Use Practices Food Safety Environment Air Water Soil Wildlife Home Page Pesticides and the Environment Water and Pesticides Related Topics: What Happens to Pesticides Released into the Environment? Water Solubility Drinking Water and Pesticides Fact Sheet

  19. Soil and Pesticides

    Science.gov (United States)

    ; Environment Human Health Animal Health Safe Use Practices Food Safety Environment Air Water Soil Wildlife Home Page Pesticides and the Environment Soil and Pesticides Related Topics: What Happens to Pesticides español Soil and Pesticides Soil can be degraded and the community of organisms living in the soil can

  20. KEK: B factory

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    After more than three years of intensive evaluation, the Japanese government has approved the conversion of the TRISTAN electronpositron collider at the national KEK Laboratory to a two-ring asymmetric B-meson factory. The project will take about five years to complete. Initial construction will proceed while TRISTAN experiments continue datataking, expected to continue until summer 1995. When it becomes operational in 1998, the new facility (TRISTAN II) will be capable of producing more than ten million B meson pairs each year. Detailed studies of their decay properties are expected to reveal answers to the long-standing puzzle of the violation of CP symmetry - combined left-right reversal and particle-antiparticle substitution

  1. SRF for neutrino factories

    International Nuclear Information System (INIS)

    Padamsee, H.

    2003-01-01

    The Neutrino Factory calls for nearly 500 meters of 200 MHz SRF cavities to provide 7.5 GV. Such a facility is more demanding than the largest SRF installation to date, i.e., LEP-II, where 500 m of niobium-coated copper cavities provided more than 3 GV of acceleration. Based on the high real estate gradient desired to minimize muon loss, superconducting cavities are selected to provide active gradients of 15 - 17 MV/m, and a real estate gradient of 7.5 MV/m. At such high gradients, the peak RF power demand for copper cavities would become prohibitively expensive. By virtue of low losses, SC cavities can be filled slowly (rise time 3 ms) reducing the peak power demand to roughly half MW per cell. (author)

  2. Positron Factory project

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Sohei; Sunaga, Hiromi; Kaneko, Hirohisa; Kawasuso, Atsuo; Masuno, Shin-ichi; Takizawa, Haruki; Yotsumoto, Keiichi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    1997-03-01

    We have started drafting a construction program for the Positron Factory, in which linac-based intense monoenergetic positron beams are planned to be applied for materials science, biotechnology and basic physics and chemistry. A technical survey study confirmed the feasibility of manufacturing a dedicated electron linac of 100 kW class with a beam energy of 100 MeV, which will produce a world-highest monoenergetic positron beam of more than 10{sup 10}/sec in intensity. A self-driven rotating converter (electrons to positrons and photons) suitable for the high power electron beam was devised and successfully tested. The practicability of simultaneous extraction of multi-channel monoenergetic positron beams with multiple moderator assemblies, which had been originated on the basis of a Monte Carlo simulation, was demonstrated by an experiment using an electron linac. An efficient moderator structure, which is composed of honeycomb-like assembled moderator foils and reflectors, is also proposed. (author)

  3. General B factory design considerations

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1992-12-01

    We describe the general considerations that go into the design of an asymmetric B factory collider. Justification is given for the typical parameters of such a facility, and the physics and technology challenges that arise from these parameter choices are discussed. Cost and schedule issues for a B factory are discussed briefly. A summary of existing proposals is presented, noting their similarities and differences

  4. The eldercare factory.

    Science.gov (United States)

    Sharkey, Noel; Sharkey, Amanda

    2012-01-01

    Rapid advances in service robotics together with dramatic shifts in population demographics have led to the notion that technology may be the answer to our eldercare problems. Robots are being developed for feeding, washing, lifting, carrying and mobilising the elderly as well as monitoring their health. They are also being proposed as a substitute for companionship. While these technologies could accrue major benefits for society and empower the elderly, we must balance their use with the ethical costs. These include a potential reduction in human contact, increased feeling of objectification and loss of control, loss of privacy and personal freedom as well as deception and infantilisation. With appropriate guidelines in place before the introduction of robots en masse into the care system, robots could improve the lives of the elderly, reducing their dependence and creating more opportunities for social interaction. Without forethought, the elderly may find themselves in a barren world of machines, a world of automated care: a factory for the elderly. Copyright © 2011 S. Karger AG, Basel.

  5. The TRIUMF KAON factory

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1991-05-01

    The TRIUMF KAON Factory is designed to produce beams of kaons, antiprotons, other hadrons and neutrinos 100 times more intense, or cleaner, than are available now, for a broad range of particle and nuclear physics experiments. This will require a 100 μA beam of 30 GeV protons, to be produced by an interleaved sequence of two fast-cycling synchrotrons and three storage rings, with the existing TRIUMF H - cyclotron as injector. An $11-million preconstruction study has enabled the overall design to be reviewed and prototypes of various components to be built and evaluated -fast-cycling dipole and quadrupole magnets, a dual-frequency magnet power supply, ceramic beam pipes with internal RF shields, an RF cavity (using perpendicular bias), an extraction kicker, and RF beam chopper, and production targets. Environmental, industrial and economic impact studies have also been completed and the cost estimates and schedule updated. The total cost of $708 million (Canadian) will be shared equally between Canada, British Columbia (already approved) and international contributors. The federal decision is expected shortly. (Author) 29 refs., 5 figs

  6. The TRIUMF KAON Factory

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1990-11-01

    The TRIUMF KAON Factory is designed to produce beams of kaons, antiprotons, other hadrons and neutrinos 100 times more intense, or cleaner, than are available now, for a broad range of experiments in particle and nuclear physics. This will require a 100 μA beam of 30 GeV protons, to be produced by an interleaved sequence of two fast-cycling synchrotrons and three storage rings, with the existing TRIUMF H - cyclotron as injector. An $11-million preconstruction study has enabled the overall design to be reviewed and prototypes of various accelerator components to be built and evaluated. Environmental, industrial and economic impact studies have also been completed. Payment of one-third of the total cost of $708 million (Canadian) has been approved by the government of British Columbia; a further third is expected from international sources, on the basis of inter-governmental consultations. A decision on the final third is expected from the government of Canada before the end of 1990. (Author) (15 refs., 7 figs.)

  7. The nearby supernova factory

    International Nuclear Information System (INIS)

    Wood-Vasey, W.M.; Aldering, G.; Lee, B.C.; Loken, S.; Nugent, P.; Perlmutter, S.; Siegrist, J.; Wang, L.; Antilogus, P.; Astier, P.; Hardin, D.; Pain, R.; Copin, Y.; Smadja, G.; Gangler, E.; Castera, A.; Adam, G.; Bacon, R.; Lemonnier, J.-P.; Pecontal, A.; Pecontal, E.; Kessler, R.

    2004-01-01

    The Nearby Supernova Factory (SNfactory) is an ambitious project to find and study in detail approximately 300 nearby Type Ia supernovae (SNe Ia) at redshifts 0.03 < z < 0.08. This program will provide an exceptional data set of well-studied SNe in the nearby smooth Hubble flow that can be used as calibration for the current and future programs designed to use SNe to measure the cosmological parameters. The first key ingredient for this program is a reliable supply of Hubble-flow SNe systematically discovered in unprecedented numbers using the same techniques as those used in distant SNe searches. In 2002, 35 SNe were found using our test-bed pipeline for automated SN search and discovery. The pipeline uses images from the asteroid search conducted by the Near Earth Asteroid Tracking group at JPL. Improvements in our subtraction techniques and analysis have allowed us to increase our effective SN discovery rate to ∼12 SNe/month in 2003

  8. Pesticide Environmental Stewardship Program (PESP)

    Science.gov (United States)

    PESP is an EPA partnership program that works with the nation's pesticide-user community to promote IPM practices. Pesticide users can reduce the risks from pests and pesticides. Members include organizations and companies in the pesticide-user community.

  9. AutoPyFactory: A Scalable Flexible Pilot Factory Implementation

    International Nuclear Information System (INIS)

    Caballero, J; Hover, J; Love, P; Stewart, G A

    2012-01-01

    The ATLAS experiment at the CERN LHC is one of the largest users of grid computing infrastructure, which is a central part of the experiment's computing operations. Considerable efforts have been made to use grid technology in the most efficient and effective way, including the use of a pilot job based workload management framework. In this model the experiment submits ‘pilot’ jobs to sites without payload. When these jobs begin to run they contact a central service to pick-up a real payload to execute. The first generation of pilot factories were usually specific to a single Virtual Organization (VO), and were bound to the particular architecture of that VO's distributed processing. A second generation provides factories which are more flexible, not tied to any particular VO, and provide new and improved features such as monitoring, logging, profiling, etc. In this paper we describe this key part of the ATLAS pilot architecture, a second generation pilot factory, AutoPyFactory. AutoPyFactory has a modular design and is highly configurable. It is able to send different types of pilots to sites and exploit different submission mechanisms and queue characteristics. It is tightly integrated with the PanDA job submission framework, coupling pilot flow to the amount of work the site has to run. It gathers information from many sources in order to correctly configure itself for a site and its decision logic can easily be updated. Integrated into AutoPyFactory is a flexible system for delivering both generic and specific job wrappers which can perform many useful actions before starting to run end-user scientific applications, e.g., validation of the middleware, node profiling and diagnostics, and monitoring. AutoPyFactory also has a robust monitoring system that has been invaluable in establishing a reliable pilot factory service for ATLAS.

  10. Pesticides poisoning

    International Nuclear Information System (INIS)

    Ahmad, I.

    1999-01-01

    Pesticides are chemical toxicants which are used to kill by their toxic actions, the pest organisms, known to incur significant economic losses or threaten human life, his health and that of his domesticated animals. These toxicants are seldom species-specific. The presence of these or their metabolites may scientific be vouched not only in the environment they are used, but in the entire ecosystem, in the subsoil, in the underwater reservoirs and in the food chain of all non-target species including man, his friends i.e. predator and parasite organisms which be uses against the pests, and in his cherished domesticated animals. In the present paper a survey is made of different groups of toxic chemicals generally used to manage pests, in the ecosystem, food chain and tissues and body parts of non-target species including man and the ones dear to him. Toxicology and biochemistry of these toxic materials and their important metabolites are also briefly discussed with special reference to ways and means through which these poison the above non-target species. (author)

  11. Pesticide Product Label System

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Pesticide Product Label System (PPLS) provides a collection of pesticide product labels (Adobe PDF format) that have been approved by EPA under Section 3 of the...

  12. Pesticide Instrumental Analysis

    International Nuclear Information System (INIS)

    Samir, E.; Fonseca, E.; Baldyga, N.; Acosta, A.; Gonzalez, F.; Felicita, F.; Tomasso, M.; Esquivel, D.; Parada, A.; Enriquez, P.; Amilibia, M.

    2012-01-01

    This workshop was the evaluation of the pesticides impact on the vegetable matrix with the purpose to determine the analysis by GC / M S. The working material were lettuce matrix, chard and a mix of green leaves and pesticides.

  13. Photon factory activity report, 1992

    International Nuclear Information System (INIS)

    1993-01-01

    This issue is the annual report of the Photon Factory, National laboratory of High Energy Physics. First, the outline of the Photon Factory is presented. Injector linac, light source, beamlines and instrumentation, the Tristan synchrotron radiation facility at the accumulation ring, and the Tristan super light facility are described in detail. The facility is open to researchers. The user's reports are collected as well. (J.P.N.) (435 refs.)

  14. Atomic Energy (factories) rules: 1988

    International Nuclear Information System (INIS)

    1988-01-01

    These rules are made by the Central Government under the Factories Act, 1948 and extend to all factories engaged in carrying out the purposes of the Atomic Energy Act, 1962. The rules cover the requirements of inspecting staff, health aspects, personnel safety, personnel welfare, working hours, employment of young persons, special provisions in case of dangerous manufacturing processes or operations, supplemental rules for administrative aspects and special powers of competent authority. (M.G.B.)

  15. Photon factory activity report, 1993

    International Nuclear Information System (INIS)

    1994-01-01

    This issue is the annual report of the Photon Factory, National Laboratory of High Energy Physics. First the outline of the Photon Factory is presented. Injector linac, light source, beamlines and instrumentation, synchrotron radiation facility at the Tristan accumulation ring, and the Tristan super light facility are described in detail. The facility is open to researchers. The user's reports are collected as well. (J.P.N.)

  16. Muon colliders and neutrino factories

    Energy Technology Data Exchange (ETDEWEB)

    Geer, S.; /Fermilab

    2010-09-01

    Over the last decade there has been significant progress in developing the concepts and technologies needed to produce, capture and accelerate {Omicron}(10{sup 21}) muons/year. This development prepares the way for a new type of neutrino source (Neutrino Factory) and a new type of very high energy lepton-antilepton collider (Muon Collider). This article reviews the motivation, design and R&D for Neutrino Factories and Muon Colliders.

  17. Pesticide exposure - Indian scene

    International Nuclear Information System (INIS)

    Gupta, P.K.

    2004-01-01

    Use of pesticides in India began in 1948 when DDT was imported for malaria control and BHC for locust control. India started pesticide production with manufacturing plant for DDT and benzene hexachloride (BHC) (HCH) in the year 1952. In 1958, India was producing over 5000 metric tonnes of pesticides. Currently, there are approximately 145 pesticides registered for use, and production has increased to approximately 85,000 metric tonnes. Rampant use of these chemicals has given rise to several short-term and long-term adverse effects of these chemicals. The first report of poisoning due to pesticides in India came from Kerala in 1958 where, over 100 people died after consuming wheat flour contaminated with parathion. Subsequently several cases of pesticide-poisoning including the Bhopal disaster have been reported. Despite the fact that the consumption of pesticides in India is still very low, about 0.5 kg/ha of pesticides against 6.60 and 12.0 kg/ha in Korea and Japan, respectively, there has been a widespread contamination of food commodities with pesticide residues, basically due to non-judicious use of pesticides. In India, 51% of food commodities are contaminated with pesticide residues and out of these, 20% have pesticides residues above the maximum residue level values on a worldwide basis. It has been observed that their long-term, low-dose exposure are increasingly linked to human health effects such as immune-suppression, hormone disruption, diminished intelligence, reproductive abnormalities, and cancer. In this light, problems of pesticide safety, regulation of pesticide use, use of biotechnology, and biopesticides, and use of pesticides obtained from natural plant sources such as neem extracts are some of the future strategies for minimizing human exposure to pesticides

  18. AutoPyFactory: A Scalable Flexible Pilot Factory Implementation

    CERN Document Server

    Caballero, J; The ATLAS collaboration; Love, P; Stewart, G

    2012-01-01

    The ATLAS experiment at the CERN LHC is one of the largest users of grid computing infrastructure, which is a central part of the experiment’s computing operations. Considerable efforts have been made to use grid technology in the most efficient and effective way, including the use of a pilot job based workload management framework. In this model the experiment submits ’pilot’ jobs to sites without payload. When these jobs begin to run they contact a central service to retrieve a real payload to execute. The first generation of pilot factories were usually specific to a single VO, and were bound to the particular architecture of that VO’s distributed processing. A second generation provides factories which are more flexible, not tied to any particular VO, and provide new or improved features such as monitoring, logging, profiling, etc. In this paper we describe this key part of the ATLAS pilot architecture, a second generation pilot factory, AutoPyFactory. AutoPyFactory has a modular design and is hig...

  19. The tau-charm factory: Experimental perspectives

    International Nuclear Information System (INIS)

    Perl, M.L.; Schindler, R.H.

    1991-09-01

    This report discusses the Tau-Charm Factory Concept; D and D S Physics at the Tau-Charm Factory; τ and ν τ Physics at the Tau-Charm Factory; and Charmonium, Gluonium and Light Quark Spectroscopy at the Tau-Charm Factory

  20. Pesticides and children

    International Nuclear Information System (INIS)

    Garry, Vincent F.

    2004-01-01

    Prevention and control of damage to health, crops, and property by insects, fungi, and noxious weeds are the major goals of pesticide applications. As with use of any biologically active agent, pesticides have unwanted side-effects. In this review, we will examine the thesis that adverse pesticide effects are more likely to occur in children who are at special developmental and behavioral risk. Children's exposures to pesticides in the rural and urban settings and differences in their exposure patterns are discussed. The relative frequency of pesticide poisoning in children is examined. In this connection, most reported acute pesticide poisonings occur in children younger than age 5. The possible epidemiological relationships between parental pesticide use or exposure and the risk of adverse reproductive outcomes and childhood cancer are discussed. The level of consensus among these studies is examined. Current concerns regarding neurobehavioral toxicity and endocrine disruption in juxtaposition to the relative paucity of toxicant mechanism-based studies of children are explored

  1. Neutrino Factory: status and prospects

    International Nuclear Information System (INIS)

    Long, K.

    2011-01-01

    The properties of the neutrino provide a unique window on physics beyond that described by the Standard Model. The study of sub-leading effects in neutrino oscillations has begun with the race to measure θ 13 consensus is emerging within the international community that a novel neutrino source is required to allow sensitive searches for leptonic CP violation to be carried out and the neutrino mass-hierarchy to be determined. The Neutrino Factory, in which intense neutrino beams are produced from the decay of muons, has been shown to out-perform the other proposed facilities. The physics case for the Neutrino Factory will be reviewed and the baseline design of the facility being developed by the International Design Study for the Neutrino Factory (the IDS-NF) collaboration will be described.

  2. Steps towards the Neutrino Factory

    International Nuclear Information System (INIS)

    Long, K.

    2012-01-01

    The properties of the neutrino provide a unique window on physics beyond that described by the Standard Model. The study of sub-leading effects in neutrino oscillations has begun with the race to measure θ 13 . A consensus is emerging within the international community that a novel neutrino source is required to allow sensitive searches for leptonic CP violation to be carried out and the neutrino mass-hierarchy to be determined. The Neutrino Factory, in which intense neutrino beams are produced from the decay of muons, has been shown to out-perform the other proposed facilities. The physics case for the Neutrino Factory will be reviewed and the baseline design of the facility being developed by the International Design Study for the Neutrino Factory (the IDS-NF) collaboration will be described.

  3. Engineering the Polyketide Cell Factory

    DEFF Research Database (Denmark)

    Mølgaard, Louise

    sufficient titers. To improve the production of polyketides biological engineering principles have been applied for the development and engineering of microbial polyketide cell factories. The two biological hosts used for heterologous polyketide production were Aspergillus nidulans and Saccharomyces...... phosphopantetheinylase (PPTase). This versatile vector system can easily be used for expression of other polyketides of interest as well as extended to express whole gene clusters. After achieving proof of principle in terms of expression, the polyketide cell factory must be optimized. The optimization can be achieved...... characterization in bioreactors revealed that the yields of 6-MSA on biomass increased albeit not significantly. As a result of this it may be argued that there is still more work to be done in terms of model building in A. nidulans. Utilizing another well-established cell factory S. cerevisiae the capabilities...

  4. Photon Factory activity report, 1991

    International Nuclear Information System (INIS)

    1992-01-01

    The Photon Factory is a national synchrotron radiation research facility affiliated with the National Laboratory for High Energy Physics located in Tsukuba Science City. The Photon Factory consists of a 2.5 GeV electron/positron linear accelerator, a 2.5 GeV electron/positron storage ring, beam lines and experimental stations. All the facilities for synchrotron radiation research are open to scientists. A part of the accumulation ring of the TRISTAN main ring has been used as a synchrotron radiation source in the energy range from 5.8 to 6.5 GeV. The Photon Factory is composed of three divisions of Injector Linac, Light Source and Instrumentation. The researches of each divisions are reviewed, and the users' short reports are collected. The list of published papers with author index is also included in the publication. (K.I.) 233 refs

  5. Math for the digital factory

    CERN Document Server

    Hömberg, Dietmar; Landry, Chantal

    2017-01-01

    This volume provides a unique collection of mathematical tools and industrial case studies in digital manufacturing. It addresses various topics, ranging from models of single production technologies, production lines, logistics and workflows to models and optimization strategies for energy consumption in production. The digital factory represents a network of digital models and simulation and 3D visualization methods for the holistic planning, realization, control and ongoing improvement of all factory processes related to a specific product. In the past ten years, all industrialized countries have launched initiatives to realize this vision, sometimes also referred to as Industry 4.0 (in Europe) or Smart Manufacturing (in the United States). Its main goals are • reconfigurable, adaptive and evolving factories capable of small-scale production • high-performance production, combining flexibility, productivity, precision and zero defects • energy and resource efficiency in manufacturing None of these...

  6. Pesticides: chemicals for survival

    International Nuclear Information System (INIS)

    Lindquist, D.A.

    1981-01-01

    Pesticides are chemicals used to control pests such as insects, weeds, plant diseases, nematodes, and rodents. The increased use of pesticides since 1945 has greatly aided the increase in crop production, protected livestock from diseases such as trypanosomiasis, protected man from diseases such as malaria and filarisis, decreased losses of stored grain, and has generally improved man's welfare. Despite the enormous benefits derived from pesticides these chemicals are not problem-free. Many pesticides are toxic to living organisms and interfere with specific biochemical systems. To measure the very small quantities of a pesticide radiolabelled chemicals are frequently essential, particularly to measure changes in the chemical structure of the pesticide, movement of the pesticide in soil, plants, or animals, amounts of pesticide going through various steps in food processing, etc. The use of radiolabelled pesticides is shortly shown for metabolism of the pesticide in crop species, metabolism in ruminant, in chickens and eggs, in soil, and possibly leaching and sorption in soil, hydrolysis, bio-concentration, microbial and photodegradation, and toxicity studies

  7. Neutrino factory plans at CERN

    CERN Document Server

    Riche, J A

    2001-01-01

    The considerable interest raised by the discovery of neutrino oscillations and recent progress in studies of muon colliders has triggered interest in considering a neutrino factory at CERN. This paper explains the reference scenario, indicates the other possible choices and mentions the R&D that are foreseen.

  8. Planned e+e- factories

    International Nuclear Information System (INIS)

    Le Duff, J.

    1993-09-01

    Various Beauty and Tau-Charm factories and projects are reviewed. Different machines (TRISTAN II, PEP II, CESR-B, the Dubna project and the European project) are compared and their design and parameters are described. (K.A.) 34 refs., 2 figs., 2 tabs

  9. Factorial representations of path groups

    International Nuclear Information System (INIS)

    Albeverio, S.; Hoegh-Krohn, R.; Testard, D.; Vershik, A.

    1983-11-01

    We give the reduction of the energy representation of the group of mappings from I = [ 0,1 ], S 1 , IRsub(+) or IR into a compact semi simple Lie group G. For G = SU(2) we prove the factoriality of the representation, which is of type III in the case I = IR

  10. A Review of "Infinity Factory."

    Science.gov (United States)

    National Council of Teachers of Mathematics, Inc., Reston, VA.

    Following a discussion of the historical background of the TV series "Infinity Factory," the goals of the television project are listed. A general description of the television series, an evaluation of the entertainment value, and an evaluation of children's attitude change are briefly presented. The program's presentation of mathematics…

  11. Pesticide Worker Safety Cooperative Agreements

    Science.gov (United States)

    The worker safety program cooperative agreements fund projects to educate pesticide applicators, handlers, and farmworkers on working safely with, and around, pesticides. Read about pesticide related grant opportunities and reports from previous grants.

  12. Models for Pesticide Risk Assessment

    Science.gov (United States)

    EPA considers the toxicity of the pesticide as well as the amount of pesticide to which a person or the environments may be exposed in risk assessment. Scientists use mathematical models to predict pesticide concentrations in exposure assessment.

  13. Understanding Pesticide Risks: Toxicity and Formulation

    OpenAIRE

    Muntz, Helen; Miller, Rhonda; Alston, Diane

    2016-01-01

    This fact sheet provides information about pesticide risks to human health, primary means of pesticide exposure, standardized measures of pesticide toxicity, pesticide signal words and type of pesticide formulations.

  14. Pesticide Program Dialogue Committee (PPDC)

    Science.gov (United States)

    The Pesticide Program Dialogue Committee, a permanent, broadly representative advisory committee, meets with EPA on a regular basis to discuss pesticide regulatory, policy, and program implementation issues.

  15. Pesticide Product Information System (PPIS)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Pesticide Product Information System contains information concerning all pesticide products registered in the United States. It includes registrant name and...

  16. Photon Factory Activity Report, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    Photon Factory Activity Report no.12 deals with our activities in the period from October 1993 through September 1994. We operate two light sources at the Photon Factory; the 2.5-GeV Photon Factory storage ring, which is a dedicated light source, and the 6.5-GeV TRISTAN Accumulation Ring, which is parasitically used as a light source. We keep more than seventy experimental stations at two facilities, and accept experiments primarily according to approval by the Program Advisory Committee. The number of proposals to the Photon Factory has been still growing. Three-hundred eighty two proposals were approved by the PAC in FY1994, which is an increase by thirteen percent compared to the previous year. Remarkable was growth in biology proposals, particularly proposals in protein crystallography. In FY 1994, we accepted approximately 20,000 man-days as general users, and almost ten percent of them were from abroad. We always open the facility to users, not only domestic but also international. Recently we have been concentrating our effort to upgrading of the light sources and reconstruction of the experimental stations to keep the Photon Factory an attractive research facility in the forthcoming years. We have already started a program of reducing the emittance of the 2.5-GeV storage ring, which now operates with an emittance of 110 nm-rad, to 27 nm-rad by modifying the lattice, with the goal of operation at the reduced emittance in the fall of 1997. We also have conceived of a conversion of the TRISTAN Accumulation Ring to a dedicated light source of high energies. The on-going TRISTAN project will terminate by the end of 1995, and the TRISTAN Main Ring will be converted to a new B-Factory. At this moment, the TRISTAN Accumulation Ring will be disused as the injector to the Main Ring, and conversion of the AR to a dedicated light source becomes possible. (J.P.N.)

  17. Photon Factory Activity Report, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    Photon Factory Activity Report no.12 deals with our activities in the period from October 1993 through September 1994. We operate two light sources at the Photon Factory; the 2.5-GeV Photon Factory storage ring, which is a dedicated light source, and the 6.5-GeV TRISTAN Accumulation Ring, which is parasitically used as a light source. We keep more than seventy experimental stations at two facilities, and accept experiments primarily according to approval by the Program Advisory Committee. The number of proposals to the Photon Factory has been still growing. Three-hundred eighty two proposals were approved by the PAC in FY1994, which is an increase by thirteen percent compared to the previous year. Remarkable was growth in biology proposals, particularly proposals in protein crystallography. In FY 1994, we accepted approximately 20,000 man-days as general users, and almost ten percent of them were from abroad. We always open the facility to users, not only domestic but also international. Recently we have been concentrating our effort to upgrading of the light sources and reconstruction of the experimental stations to keep the Photon Factory an attractive research facility in the forthcoming years. We have already started a program of reducing the emittance of the 2.5-GeV storage ring, which now operates with an emittance of 110 nm-rad, to 27 nm-rad by modifying the lattice, with the goal of operation at the reduced emittance in the fall of 1997. We also have conceived of a conversion of the TRISTAN Accumulation Ring to a dedicated light source of high energies. The on-going TRISTAN project will terminate by the end of 1995, and the TRISTAN Main Ring will be converted to a new B-Factory. At this moment, the TRISTAN Accumulation Ring will be disused as the injector to the Main Ring, and conversion of the AR to a dedicated light source becomes possible. (J.P.N.)

  18. Photon Factory Activity Report, 1994

    International Nuclear Information System (INIS)

    1995-01-01

    Photon Factory Activity Report no.12 deals with our activities in the period from October 1993 through September 1994. We operate two light sources at the Photon Factory; the 2.5-GeV Photon Factory storage ring, which is a dedicated light source, and the 6.5-GeV TRISTAN Accumulation Ring, which is parasitically used as a light source. We keep more than seventy experimental stations at two facilities, and accept experiments primarily according to approval by the Program Advisory Committee. The number of proposals to the Photon Factory has been still growing. Three-hundred eighty two proposals were approved by the PAC in FY1994, which is an increase by thirteen percent compared to the previous year. Remarkable was growth in biology proposals, particularly proposals in protein crystallography. In FY 1994, we accepted approximately 20,000 man-days as general users, and almost ten percent of them were from abroad. We always open the facility to users, not only domestic but also international. Recently we have been concentrating our effort to upgrading of the light sources and reconstruction of the experimental stations to keep the Photon Factory an attractive research facility in the forthcoming years. We have already started a program of reducing the emittance of the 2.5-GeV storage ring, which now operates with an emittance of 110 nm-rad, to 27 nm-rad by modifying the lattice, with the goal of operation at the reduced emittance in the fall of 1997. We also have conceived of a conversion of the TRISTAN Accumulation Ring to a dedicated light source of high energies. The on-going TRISTAN project will terminate by the end of 1995, and the TRISTAN Main Ring will be converted to a new B-Factory. At this moment, the TRISTAN Accumulation Ring will be disused as the injector to the Main Ring, and conversion of the AR to a dedicated light source becomes possible. (J.P.N.)

  19. Handbook factory planning and design

    CERN Document Server

    Wiendahl, Hans-Peter; Nyhuis, Peter

    2015-01-01

    This handbook introduces a methodical approach and pragmatic concept for the planning and design of changeable factories that act in strategic alliances to supply the ever-changing needs of the global market. In the first part, the change drivers of manufacturing enterprises and the resulting new challenges are considered in detail with focus on an appropriate change potential. The second part concerns the design of the production facilities and systems on the factory levels work place, section, building and site under functional, organisational, architectural and strategic aspects keeping in mind the environmental, health and safety aspects including corporate social responsibility. The third part is dedicated to the planning and design method that is based on a synergetic interaction of process and space. The accompanying project management of the planning and construction phase and the facility management for the effective utilization of the built premises close the book. -        Concise overview o...

  20. RIKEN RI Beam Factory project

    Energy Technology Data Exchange (ETDEWEB)

    Yano, Yasushige; Goto, Akira; Katayama, Takeshi [Institute of Physical and Chemical Research, Wako, Saitama (Japan)

    1997-03-01

    The RARF proposes `RIKEN RI Beam Factory` as a next facility-expanding project. The factory makes it the primary aim to provide RI (Radioactive Isotope) beams covering over the whole atomic-mass range with the world-highest intensity in a wide energy range up to several hundreds MeV/nucleon. These RI beams are generated by the fragmentation of high-intensity heavy-ion beams. For the efficient production heavy-ion energies will be boosted up to over 100 MeV/nucleon even for very heavy ions by a K2500-MeV superconducting ring cyclotron serving as a post accelerator of the existing K540-MeV ring cyclotron. A new type of experimental installation called `MUSES` (Multi-USe Experimental Storage rings) will be constructed as well. With MUSES, various types of unique colliding experiments will become possible. (author)

  1. On KEK B-Factory

    Science.gov (United States)

    Sugawara, H.

    2009-07-01

    There are two principles which the management of a research institute like KEK must respect when dealing with such big project as B-Factory. One is the scientific merit of the project and the other is the organizational consideration which includes financial, human, technical and historical elements. Ideally, the two principles are to be fully taken into account. But, in many cases, one or the other is only partially fulfilled due to unavoidable circumstances. The lack of flexibility to respond to all possible situations is more dangerous and may lead to a disaster as in the case of SSC. I will describe the process which lead to the successful construction, operation and physics presentations of KEK B-Factory following faithfully the official records.

  2. On KEK B-factory

    International Nuclear Information System (INIS)

    Sugawara, Hirotaka

    2009-01-01

    There are two principles which the management of a research institute like KEK must respect when dealing with such big project as B-Factory. One is the scientific merit of the project and the other is the organizational consideration which includes financial, human, technical and historical elements. Ideally, the two principles are to be fully taken into account. But, in many cases, one or the other is only partially fulfilled due to unavoidable circumstances. The lack of flexibility to respond to all possible situations is more dangerous and may lead to a disaster as in the case of SSC. I will describe the process which lead to the successful construction, operation and physics presentations of KEK B-Factory following faithfully the official records. (author)

  3. Apiary B Factory lattice design

    International Nuclear Information System (INIS)

    Donald, M.H.R.; Garren, A.A.

    1991-04-01

    The Apiary B Factory is a proposed high-intensity electron-positron collider. This paper will present the lattice design for this facility, which envisions two rings with unequal energies in the PEP tunnel. The design has many interesting optical and geometrical features due to the needs to conform to the existing tunnel, and to achieve the necessary emittances, damping times and vacuum. Existing hardware is used to a maximum extent. 8 figs. 1 tab

  4. A kaon factory for TRIUMF

    International Nuclear Information System (INIS)

    Measday, D.F.

    1988-11-01

    The design study for the TRIUMF Kaon Factory has recently been funded. A short discussion of the scientific motivation is given first, followed by a brief description of the 30 GeV synchrotron which is being proposed. There will be five rings altogether using the present TRIUMF 500 MeV cyclotron as an injector. If the project is funded in 1990 the accelerators would be completed in 1995 or so, and the experimental programme would start a year later

  5. Control of Pesticides 2001

    DEFF Research Database (Denmark)

    Krongaard, T.; Petersen, K. K.; Christoffersen, C.

    comply with the label-claimed content. The tolerance of deviation from the label-claimed content of active ingredient is set by the Danish pesticide regulation. Three different groups of products covered by the pesticide regulation have been included in the 2001 analytical chemical authority control: 1...

  6. Pesticides in Ground Water

    DEFF Research Database (Denmark)

    Bjerg, Poul Løgstrup

    1996-01-01

    Review af: Jack E. Barbash & Elizabeth A. Resek (1996). Pesticides in Ground Water. Distribution trends and governing factors. Ann Arbor Press, Inc. Chelsea, Michigan. pp 588.......Review af: Jack E. Barbash & Elizabeth A. Resek (1996). Pesticides in Ground Water. Distribution trends and governing factors. Ann Arbor Press, Inc. Chelsea, Michigan. pp 588....

  7. National Pesticide Information Center

    Science.gov (United States)

    ... How can I protect my pets when using pesticides around them? More FAQs FAQ Comics Video FAQs From NPIC: Fact Sheets Videos Web Apps Podcasts Outreach Materials NPIC Professional Resources Social Media: National Pesticide Information Center Tweets by NPICatOSU Please read our ...

  8. Food and Pesticides

    Science.gov (United States)

    EPA sets limits on how much of a pesticide may be used on food during growing and processing, and how much can remain on the food you buy. Learn about regulation of pesticides on food and how you can limit exposure.

  9. Photon Factory activity report, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The Photon Factory at the National Laboratory for High Energy Physics is a national facility for scientific research utilizing synchrotron radiation. Although the Photon Factory operator the linear injector, two light sources including the 2.5 GeV storage ring and the 6.5 GeV TRISTAN accumulation Ring as well as a major fraction of their beamlines and experimental station. This report is covered the period from October 1994 to September 1995. The total number of proposals by this PAC was 399 in 1995. Facility development projects currently in progress include the following, TRISTAN Super Light Facility (TSLF) project, VUV-FEL project, KEKB project and Slow-positron Source. This report contents outline of the Photon Factory, introduction, scientific disciplines, electronic properties of condensed matters, atomic and molecular science, X-ray imaging, radiobiology using synchrotron radiation, structural properties of condensed matters, structural properties of solid surfaces and adsorbates, structure and function of proteins, theoretical researches, experimental facilities, beamlines, new instrumentation, AR Upgrade, collaborations, projects, user`s short reports, list of published papers 1994/95. (S.Y.)

  10. Photon Factory activity report, 1995

    International Nuclear Information System (INIS)

    1996-01-01

    The Photon Factory at the National Laboratory for High Energy Physics is a national facility for scientific research utilizing synchrotron radiation. Although the Photon Factory operator the linear injector, two light sources including the 2.5 GeV storage ring and the 6.5 GeV TRISTAN accumulation Ring as well as a major fraction of their beamlines and experimental station. This report is covered the period from October 1994 to September 1995. The total number of proposals by this PAC was 399 in 1995. Facility development projects currently in progress include the following, TRISTAN Super Light Facility (TSLF) project, VUV-FEL project, KEKB project and Slow-positron Source. This report contents outline of the Photon Factory, introduction, scientific disciplines, electronic properties of condensed matters, atomic and molecular science, X-ray imaging, radiobiology using synchrotron radiation, structural properties of condensed matters, structural properties of solid surfaces and adsorbates, structure and function of proteins, theoretical researches, experimental facilities, beamlines, new instrumentation, AR Upgrade, collaborations, projects, user's short reports, list of published papers 1994/95. (S.Y.)

  11. Photon Factory activity report, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The Photon Factory at the National Laboratory for High Energy Physics is a national facility for scientific research utilizing synchrotron radiation. Although the Photon Factory operator the linear injector, two light sources including the 2.5 GeV storage ring and the 6.5 GeV TRISTAN accumulation Ring as well as a major fraction of their beamlines and experimental station. This report is covered the period from October 1994 to September 1995. The total number of proposals by this PAC was 399 in 1995. Facility development projects currently in progress include the following, TRISTAN Super Light Facility (TSLF) project, VUV-FEL project, KEKB project and Slow-positron Source. This report contents outline of the Photon Factory, introduction, scientific disciplines, electronic properties of condensed matters, atomic and molecular science, X-ray imaging, radiobiology using synchrotron radiation, structural properties of condensed matters, structural properties of solid surfaces and adsorbates, structure and function of proteins, theoretical researches, experimental facilities, beamlines, new instrumentation, AR Upgrade, collaborations, projects, user`s short reports, list of published papers 1994/95. (S.Y.)

  12. Photon Factory activity report, 1990

    International Nuclear Information System (INIS)

    1991-01-01

    The Photon Factory has grown at a considerable rate, and 600 experiments are carried out in 1991, while the number of users is now 2300 including about 500 from industrial sectors. The use of synchrotron radiation increased from fundamental research to industrial development. The development at the Photon Factory is supported by the capability of the accelerators. At present, the 2.5 GeV PF ring is operated with positrons at the initial beam current of 350 mA. The total operation time was 3500 hours in the fiscal year 1990. The development of an avalanche mode photodiode, the observation of quantum beat in the experiment of nuclear Bragg scattering, the measurement of photo-electron and photo-ion spectroscopy were carried out. The conversion of TRISTAN main ring to an ultrahigh brilliance and high coherence source is planned for the future. The annual PF Symposium was held, and Professor H. Winick gave the lecture 'Ultrahigh brightness and coherent radiation from large storage rings'. In this report, the outline of the Photon Factory and the activities in Divisions of Injector Linac, Light Source and Instrumentation are described. (K.I.)

  13. PESTICIDES: BENEFITS AND HAZARDS

    Directory of Open Access Journals (Sweden)

    Ivan Maksymiv

    2015-05-01

    Full Text Available Pesticides are an integral part of modern life used to prevent growth of unwanted living  organisms. Despite the fact that scientific statements coming from many toxicological works provide indication on the low risk of the pesticides and their residues, the community especially last years is deeply concerned about massive application of pesticides in diverse fields. Therefore evaluation of hazard risks particularly in long term perspective is very important. In the fact there are at least two clearly different approaches for evaluation of pesticide using: the first one is defined as an objective or probabilistic risk assessment, while the second one is the potential economic and agriculture benefits. Therefore, in this review the author has considered scientifically based assessment of positive and negative effects of pesticide application and discusses possible approaches to find balance between them.

  14. Pesticide Exposure in Children

    Science.gov (United States)

    Roberts, James R.; Karr, Catherine J.

    2018-01-01

    Pesticides are a collective term for a wide array of chemicals intended to kill unwanted insects, plants, molds, and rodents. Food, water, and treatment in the home, yard, and school are all potential sources of children’s exposure. Exposures to pesticides may be overt or subacute, and effects range from acute to chronic toxicity. In 2008, pesticides were the ninth most common substance reported to poison control centers, and approximately 45% of all reports of pesticide poisoning were for children. Organophosphate and carbamate poisoning are perhaps the most widely known acute poisoning syndromes, can be diagnosed by depressed red blood cell cholinesterase levels, and have available antidotal therapy. However, numerous other pesticides that may cause acute toxicity, such as pyrethroid and neonicotinoid insecticides, herbicides, fungicides, and rodenticides, also have specific toxic effects; recognition of these effects may help identify acute exposures. Evidence is increasingly emerging about chronic health implications from both acute and chronic exposure. A growing body of epidemiological evidence demonstrates associations between parental use of pesticides, particularly insecticides, with acute lymphocytic leukemia and brain tumors. Prenatal, household, and occupational exposures (maternal and paternal) appear to be the largest risks. Prospective cohort studies link early-life exposure to organophosphates and organochlorine pesticides (primarily DDT) with adverse effects on neurodevelopment and behavior. Among the findings associated with increased pesticide levels are poorer mental development by using the Bayley index and increased scores on measures assessing pervasive developmental disorder, inattention, and attention-deficit/hyperactivity disorder. Related animal toxicology studies provide supportive biological plausibility for these findings. Additional data suggest that there may also be an association between parental pesticide use and adverse birth

  15. The Influence of Industrial Waste on Pesticide and Heavy Metal Conetnts in Cipinang-Sunter River Water Jakarta

    International Nuclear Information System (INIS)

    Ulfa, T S; Mellawati, J; Sofni, M C

    1996-01-01

    The measurement of pesticide and heavy metal contents of river water in upperstream (around some factories), and downstream (housing area), along Cipinang-Sunter river Jakarta, on February-June 1996 had been done. The aim of the measurement was to get information about the influence of factories waste on pesticide and heavy metal contents in the Cipinang river water. Gas and liquid chromatographis were used to measure the pesticide content and X-ray fluorecence spectrometry was used to measure the heavy metals content. Result of the measurements showed that Cipinang river water has contained some organochlorin pesticides, i.e., BHC, a and b endosulfan, dieldrin, pp-DDE, and heavy metals, i.e., Ti, V, Cr, Fe, Ni, Cu, Zn, and Pb

  16. Information security of Smart Factories

    Science.gov (United States)

    Iureva, R. A.; Andreev, Y. S.; Iuvshin, A. M.; Timko, A. S.

    2018-05-01

    In several years, technologies and systems based on the Internet of things (IoT) will be widely used in all smart factories. When processing a huge array of unstructured data, their filtration and adequate interpretation are a priority for enterprises. In this context, the correct representation of information in a user-friendly form acquires special importance, for which the market today presents advanced analytical platforms designed to collect, store and analyze data on technological processes and events in real time. The main idea of the paper is the statement of the information security problem in IoT and integrity of processed information.

  17. Muon Colliders and Neutrino Factories

    Energy Technology Data Exchange (ETDEWEB)

    Kaplan, Daniel M. [IIT, Chicago

    2015-05-29

    Muon colliders and neutrino factories are attractive options for future facilities aimed at achieving the highest lepton-antilepton collision energies and precision measurements of Higgs boson and neutrino mixing matrix parameters. The facility performance and cost depend on how well a beam of muons can be cooled. Recent progress in muon cooling design studies and prototype tests nourishes the hope that such facilities could be built starting in the coming decade. The status of the key technologies and their various demonstration experiments is summarized. Prospects "post-P5" are also discussed.

  18. Magnets for TRIUMF's KAON factory

    International Nuclear Information System (INIS)

    Otter, A.J.; Reeve, P.A.

    1991-05-01

    The KAON Factory will require over 2000 magnets to transport protons from the existing 500 Mev cyclotron through three storage rings and two synchrotrons and deliver them to the experimental area at 30 Gev. The magnet requirements are summarized and the results of measurements on prototypes for the 50 hz Booster magnets are compared with design values. This paper will address three topics: the results of prototype work, some of the more difficult design aspects of other magnets and the tolerances required to achieve production magnets uniform to ± 2 parts in 10 4 . (Author) 10 refs., 3 figs., tab

  19. Photon Factory activity report, 1988

    International Nuclear Information System (INIS)

    1989-01-01

    Since the foundation of Photon Factory a decade age, it has played an important role as a unique synchrotron X-ray radiation source in Japan. Installation of various insertion devices, storage of intense positron beam and reduction of beam emittance were the substantial achievements in the last several years. The exploitation of the TRISTAN Accumulation Ring as a synchrotron radiation source has paved the way for a new potential of development. All these activities have brought about the increase of beamlines and the expansion of scientific fronts. Third International Conference on Synchrotron Radiation Instrumentation held in Tsukuba was one of the most highlighted events for the facility. In coming years, it is intended to open new research fields using the promising single bunch beam and circularly polarized wiggler radiation. The TRISTAN Main Ring also will be applied to synchrotron radiation research. The Photon Factory in a national synchrotron radiation research facility affiliated to the National Laboratory for High Energy Physics, and it consists of a 2.5 GeV electron linac, a 2.5 GeV storage ring as a synchrotron light source, beam lines and experimental stations. The operation, improvement and development in respective departments are reported. (Kako, I.)

  20. Reducing Pesticide Drift

    Science.gov (United States)

    Provides information about pesticide spray drift, including problems associated with drift, managing risks from drift and the voluntary Drift Reduction Technology program that seeks to reduce spray drift through improved spray equipment design.

  1. Types of Pesticide Ingredients

    Science.gov (United States)

    Pesticide active ingredients are described by the types of pests they control or how they work. For example, algicides kill algae, biopesticides are derived from natural materials, and insecticides kill insects.

  2. Pesticides and Pregnancy

    Science.gov (United States)

    ... It is unlikely that having your home or workplace treated by a professional exterminator will result in a high enough exposure to increase the risk to a pregnancy. To reduce exposure to pesticides found on food, ...

  3. What are Antimicrobial Pesticides?

    Science.gov (United States)

    Antimicrobial pesticides are substances or mixtures of substances used to destroy or suppress the growth of harmful microorganisms such as bacteria, viruses, or fungi on inanimate objects and surfaces.

  4. What Is a Pesticide?

    Science.gov (United States)

    ... Directory Planning, Budget and Results Jobs and Internships Headquarters Offices Regional Offices Labs and Research Centers Related ... pesticide's distribution, sale, and use only after the company meets the scientific and regulatory requirements. In evaluating ...

  5. Control of Pesticides 2004

    DEFF Research Database (Denmark)

    Krongaard, T.; Petersen, K. K.; Christoffersen, C.

    Four different groups of products covered by the pesticide regulation were included in the 2004 analytical chemical authority control: 1) Herbicides containing bentazone, dicamba, dichlorprop-P, mecoprop-P, MCPA, foramsulfuron, iodosulfuron-methylsodium, rimsulfuron and triasulfuron. 2) Fungicides...

  6. Pesticide Registration Information System

    Data.gov (United States)

    U.S. Environmental Protection Agency — PRISM provides an integrated, web portal for all pesticide related data, communications, registrations and transactions for OPP and its stakeholders, partners and...

  7. Control of Pesticides 2000

    DEFF Research Database (Denmark)

    Krongaard, T.; Petersen, K. K.; Christoffersen, C.

    , fluazinam, and kresoximmethyl. 3) Insecticides containing buprofezin and fenazaquin. All products were examined for content of active ingredient. Satisfactory results were found among herbicides containing aclonifen, dicamba, quinoclamine, bromoxynil, and simazine, among fungicides containing fenpropidin......, fluazinam, and kresoxim-methyl, and among insecticides containing fenazaquin. Thus, all the eighteen analysed samples of these pesticides complied with the accepted tolerances with respect to content of active ingredients set by the Danish regulation of pesticides. The only product containing buprofezin...

  8. Information Management for Factory Planning and Design

    OpenAIRE

    Chen, Danfang

    2012-01-01

    This thesis is dedicated to the manufacturing industry for the improvement of information management within the factory planningand design domain, and for more efficient factory planning and design. Currently the manufacturing industry lacks sufficient methods for capturing, structuring, and representing information and knowledge for easy access, exchange, integration and reuse within the domain. Therefore the focus of this thesis is on information and knowledge management within factory plan...

  9. WQO is Decidable for Factorial Languages

    KAUST Repository

    Atminas, Aistis

    2017-08-08

    A language is factorial if it is closed under taking factors, i.e. contiguous subwords. Every factorial language can be described by an antidictionary, i.e. a minimal set of forbidden factors. We show that the problem of deciding whether a factorial language given by a finite antidictionary is well-quasi-ordered under the factor containment relation can be solved in polynomial time. We also discuss possible ways to extend our solution to permutations and graphs.

  10. Preserving the Modernist Vertical Urban Factory

    Directory of Open Access Journals (Sweden)

    Nina Rappaport

    2016-07-01

    Full Text Available This essay is adapted in part, from the section, “Modern Factory Architecture” case studies from Nina Rappaport’s book Vertical Urban Factory, published by Actar this spring. Vertical Urban Factory began as an architecture studio, and then an exhibition, which opened in New York in 2011 and traveled to Detroit and Toronto in 2012. Last year the show was displayed at Archizoom at EPFL in Lausanne; Industry City, Brooklyn; and the Charles Moore School of Architecture at Kean University, in New Jersey. The project continues as a think tank evaluating factory futures and urban industrial potential.

  11. Photon Factory activity report, 1987

    International Nuclear Information System (INIS)

    1987-01-01

    The Photon Factory made great strides in 1987. The low emittance operation of the PF ring was achieved in March, and resulted favorably in the increase of brilliance from 2 to 20 times for all the beam lines with high beam stability. At the same time, the installation of inserted devices was under way for all available straight sections of the ring. A 54-pole wiggler-undulator has been commissioned at BL-16. The devices to be inserted in the near future are a multipole wiggler for BL-13, an undulator for BL-19, and an undulator for circular polarized radiation at BL-28. The construction of beam lines continued, and four new beam lines, BL-6, BL-9, BL-16 and BL-17, are now in operation, BL-13 and BL-19 are under construction, and BL-3, BL-5, BL-18, BL-20 and BL-28 are in the design stage. Since its inauguration with four beam lines in 1982, the Photon Factory has grown rapidly, and approaches the goal of operating the PF ring with positrons in full use of its 24 beam ports and the straight sections for inserted devices. The total operation time was limited to 3,000 hours by the budget for fiscal year 1987, and about 80 % of the operation hours were devoted to the experiments of users. The nearly perfect operation of the 400 m long linac has continued in 1987, and has supplied both electrons and positrons to the TRISTAN collision experiment. The light source of a 2.5 GeV electron storage ring was normally operated. (Kako, I.)

  12. Organochlorine pesticide level differences among female inhabitants from Veracruz, Puebla and Tabasco, Mexico.

    Science.gov (United States)

    Waliszewski, Stefan M; Caba, M; Saldarriaga-Noreña, H; Martínez, A J; Meza, E; Valencia Quintana, R; Zepeda, R

    2014-08-01

    Organochlorine pesticides have been used in Mexico in malaria control programs and against ectoparasites. The objective of this study was to compare the levels of organochlorine pesticides: HCB, α-β-γ-HCH, pp'-DDE, op'-DDT and pp'-DDT in adipose tissue of female inhabitants from three Mexican states: Veracruz, Puebla and Tabasco. Data analyses indicated higher β-HCH levels in Puebla inhabitants. When comparing the mean values of the pp'-DDE concentrations among the three states, no statistically significant differences were noted. A trend of increasing concentrations of op'-DDT from Veracruz to Puebla and Tabasco was observed. Significantly higher pp'-DDT concentrations in Veracruz as compared to Puebla and Tabasco were determined. Using factorial analysis of three age categories (>30, 31-50, pesticide concentrations increases with age of participants, indicating time of exposure as a principal factor of organochlorine pesticides accumulation in adipose tissue.

  13. Antimicrobial Pesticide Use Site Index

    Science.gov (United States)

    This Use Site Index provides guidance to assist applicants for antimicrobial pesticide registration by helping them identify the data requirements necessary to register a pesticide or support their product registrations.

  14. Human Health Benchmarks for Pesticides

    Data.gov (United States)

    U.S. Environmental Protection Agency — Advanced testing methods now allow pesticides to be detected in water at very low levels. These small amounts of pesticides detected in drinking water or source...

  15. A Tau-Charm Factory at CEBAF

    Energy Technology Data Exchange (ETDEWEB)

    Seth, K.K. [Northwestern Univ., Evanston, IL (United States)

    1994-04-01

    It is proposed that a Tau Charm Factory represents a natural extension of CEBAF into higher energy domains. The exciting nature of the physics of charm quarks and tau leptons is briefly reviewed and it is suggested that the concept of a linac-ring collider as a Tau Charm Factory at CEBAF should be seriously studied.

  16. Photon Factory activity report, 1989

    International Nuclear Information System (INIS)

    1990-01-01

    At the Photon Factory about 500 experiments are now running annually with about 50 experimental stations, the total operation time of the 2.5 GeV storage ring was 3400 hour in 1989, and the number of users was more than 2000, including 300 scientists from industry. This wide usage of synchrotron radiation has been supported by good performance of the accelerators. The positron beam current of the linac was increased for rapid injection (injection time: 20 min). The entire roof of the Light Source building was covered with thermal insulator (urethane-foam). This has greatly improved the beam stability of the ring. It has been operated at an initial ring current of 350 mA with a life time of 20 hours. Distinctive instrumentation at the Photon Factory has expanded to various fields such as angle-resolved ion-spectroscopy, dispersive EXAFS, trace impurity X-ray fluorescence analysis, plane-wave topography, structure analysis under high pressure, and imaging plates. Recently, experiments of protein structure analysis have been carried out extensively; Sakabe developed a new type of Weissenberg camera for protein crystallography, and about 50 experiments have been done for the past six months by a combination of Sakabe camera and imaging plates. The 2.5 GeV light source is now at an entrance of its harvest season. The TRISTAN Accumulation Ring has been used throughout this year in a time sharing basis with the TRISTAN experiment; twenty minutes for injection to TRISTAN Main Ring and 2 hours for SR experiment. The main subject has been magnetic Compton scattering with circularly polarized wiggler radiation. Such experiences enable us to expand our perspective for research in the following decade; we are investigating the possibility of operating the TRISTAN Main Ring at 6-8 GeV with 6000-pole undulaters, resulting in an extremely brilliant radiation source (Emittance: 0.1 nm·rad at 5 GeV with damping rings). (J.P.N.)

  17. The KAON Factory at TRIUMF

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1992-08-01

    The TRIUMF KAON Factory is designed to produce beams of kaons, antiprotons, other hadrons and neutrinos 100 times more intense, or cleaner, than are available now, for a broad range of particle and nuclear physics experiments. This will require a 100 μA beam of 30 GeV protons, to be produced by an interleaved sequence of two fast-cycling synchrotrons and three storage rings, with the existing TRIUMF H - cyclotron as injector. An $11-million preconstruction study has enabled the overall design to be reviewed and prototypes of various components to be built and evaluated -fast-cycling dipole and quadrupole magnets, a dual-frequency magnet power supply, ceramic beam pipes with internal rf shields, and rf cavity (using perpendicular bias), an extraction kicker, and rf beam chopper, and production targets. Environmental, industrial and economic impact studies have also been completed and the cost estimates and schedule updated. The total cost of $708 million (Canadian) will be shared equally between Canada, British Columbia and international contributors: the first two-thirds of this sum have already been approved and negotiations for the remainder are under way. 25 refs., 7 figs

  18. The KAON factory at TRIUMF

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1992-07-01

    The TRIUMF KAON Factory is designed to produce beams of kaons, antiprotons, other hadrons and neutrinos 100 times more intense, or cleaner, than are available now, for a broad range of particle and nuclear physics experiments. This will require a 100 μA beam of 30 GeV protons, to be produced by an interleaved sequence of two fast-cycling synchrotrons and three storage rings, with the existing TRIUMF H - cyclotron as injector. An $11-million pre-construction study has enabled the overall design to be reviewed and prototypes of various components to be built and evaluated: fast-cycling dipole and quadrupole magnets, a dual frequency magnet power supply, ceramic beam pipes with internal rf shields, an rf cavity (using perpendicular bias), an extraction kicker, an rf beam chopper, and production targets. Environmental, industrial and economic impact studies have also been completed and the cost estimates and schedule updated. The total cost of $708 million (Canadian) will be shared equally between Canada, British Columbia and international contributors; the first two-thirds of this sum have already been approved and negotiations for the remainder are under way. 26 refs., 6 figs

  19. Radiation-adsorption purification of effluents containing pesticides

    International Nuclear Information System (INIS)

    Brusentseva, S.A.; Shubin, V.N.; Nikonorova, G.K.; Zorin, D.M.; Sosnovskaya, A.A.; Petryaev, E.P.; Vlasova, V.I.; Edimicheva, I.P.; Subbotina, N.N.; Belorusskij Gosudarstvennyj Univ., Minsk)

    1986-01-01

    The radiation-adsorption purification is one of the new direction in the radiation purification of natural wastes and effluents containing pesticides. This method combines the conventional adsorption purification with radiation treatment of the sorbent, and the result the protection time of the sorbent increases due to the radiation regeneration of carbon. In present work the method was used for purification of effluents from pesticides, such as 4,4'Dichlorodiphenyltrichloroethane /DDT/, 1,2,3,4,5,6-hexachlorocyclohexane /HCCH/, dimethyl 2,2-dichlorovinylphosphate /DDVF/ and petroleum products (a mixture of kerosene and xylene in ratio 7:1). Such effluents are formed at factories producing an insecticide aerosol 'Prime-71'. Three investigations were carried out on model with a solution similar composition to industrial effluents. (author)

  20. Factorial structure of aerobics athletes’ fitness

    Directory of Open Access Journals (Sweden)

    T.V. Shepelenko

    2017-11-01

    Full Text Available The purpose of the research is to develop an algorithm of teams’ formation in sport aerobics and to define factorial structure of athletes’ fitness. Material : in the research sport aerobics’ athletes (n=19 participated. All athletes are members of Kharkiv national team (Ukraine. All athletes underwent complete medical examination. The functional condition of an organism (arterial blood pressure, indicators of a variability of the rhythm of the heart, treadbahn testing, psycho-physiological state (time’s determination of simple and complex reaction were defined. The physical development and physical fitness and stability of vestibular system were also defined. The factorial and cluster analysis were used. Results : The algorithm of teams’ formation in sport aerobics is developed for performances in various competitive categories. The algorithm contains all stages of standard procedure of the factorial and cluster analysis. In the factorial analysis the individual factorial values were also defined. Conclusions : The obtained data are recommended to be used at teams’ formation for performances in various competitive categories: team formation for pair and group performances. The general and individual factorial structure of athletes’ complex fitness is defined. It is possible to select athletes with similar qualities and with different qualities for the mixed performances. The determination of individual factorial structure of fitness permits to estimate objectively variants of athletes’ formation in groups.

  1. SatisFactory Final System Evaluation Report

    OpenAIRE

    Sunlight SA

    2018-01-01

    The present document is a deliverable of the SatisFactory project, funded by the European Commission’s Directorate-General for Research and Innovation (DG RTD), under its Horizon 2020 Research and innovation programme (H2020). The main objective of this deliverable is to report on the SatisFactory Final System Evaluation, with regards to the industrial pilots at COMAU and SUNLIGHT. The evaluation of SatisFactory platform is based on the implementation of the business scenarios where each tool...

  2. STANFORD (SLAC): B factory construction begins

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1994-03-15

    At a ceremony marking the start of construction, members of the US Congress and Secretary of Energy Hazel O'Leary hailed the new Asymmetric B Factory as the key to continued vitality of the Stanford Linear Accelerator Center (SLAC). Being built in collaboration with the Lawrence Berkeley Laboratory and the Lawrence Livermore National Laboratory, the B factory is a $177 million upgrade of the existing PEP electron-positron collider. Scheduled for completion in 1998, the B factory will generate many millions of B mesons, allowing, among other physics, an intensive search for the phenomena of CP violation in the decays of these particles.

  3. STANFORD (SLAC): B factory construction begins

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    At a ceremony marking the start of construction, members of the US Congress and Secretary of Energy Hazel O'Leary hailed the new Asymmetric B Factory as the key to continued vitality of the Stanford Linear Accelerator Center (SLAC). Being built in collaboration with the Lawrence Berkeley Laboratory and the Lawrence Livermore National Laboratory, the B factory is a $177 million upgrade of the existing PEP electron-positron collider. Scheduled for completion in 1998, the B factory will generate many millions of B mesons, allowing, among other physics, an intensive search for the phenomena of CP violation in the decays of these particles

  4. Factorial correlators: angular scaling within QCD jets

    International Nuclear Information System (INIS)

    Peschanski, R.

    2001-01-01

    Factorial correlators measure the amount of dynamical correlation in the multiplicity between two separated phase-space windows. We present the analytical derivation of factorial correlators for a QCD jet described at the double logarithmic (DL) accuracy. We obtain a new angular scaling property for properly normalized correlators between two solid-angle cells or two rings around the jet axis. Normalized QCD factorial correlators scale with the angular distance and are independent of the window size. Scaling violations are expected beyond the DL approximation, in particular from the subject structure. Experimental tests are feasible, and thus would be welcome. (orig.)

  5. Deficits and Solutions in the Development of Modular Factory Systems

    OpenAIRE

    Achim Kampker; Peter Burggräf; Moritz Krunke; Hanno Voet

    2017-01-01

    As a reaction to current challenges in factory planning, many companies think about introducing factory standards to lower planning times and decrease planning costs. If these factory standards are set-up with a high level of modularity, they are defined as modular factory systems. This paper deals with the main current problems in the application of modular factory systems in practice and presents a solution approach with its basic models. The methodology is based on methods from factory pla...

  6. Control of Pesticides 2006

    DEFF Research Database (Denmark)

    Krongaard, Teddy; Petersen, Kitty Kastalag; Christoffersen, Christel

    in the products comply with the labelled content. The tolerance of deviation from the labelled content of active ingredient is set by the Danish Statutory Order on pesticides. In addition to the examination of the content of active ingredients, all collected samples are examined for the content of octylphenol...

  7. Citizen's Guide to Pesticides.

    Science.gov (United States)

    Environmental Protection Agency, Washington, DC. Office of Pesticide Programs.

    This guide provides suggestions on pest control and safety rules for pesticide use at home. Pest prevention may be possible by modification of pest habitat: removal of food and water sources, removal or destruction of pest shelter and breeding sites, and good horticultural practices that reduce plant stress. Nonchemical alternatives to pesticides…

  8. The Danish Pesticide Tax

    DEFF Research Database (Denmark)

    Pedersen, Anders Branth; Nielsen, Helle Ørsted; Andersen, Mikael Skou

    2015-01-01

    pesticide taxes on agriculture, which makes it interesting to analyze how effective they have been. Here the effects of the ad valorem tax (1996-2013) are analyzed. The case study demonstrates the challenges of choosing an optimal tax design in a complex political setting where, additionally, not all...

  9. The factory as a battlefield

    Directory of Open Access Journals (Sweden)

    Helena Chávez Mac Gregor

    Full Text Available The crisis of labour is also one of representation. Some contemporary artists working with moving images have been questioning how to represent capital, labour and the worker. Isaac Julien or Harun Farocki, for example, have focused on interlacing characters - from fiction or reality - with geopolitical spaces in order to present the entanglement of the economical new order with the new forms of labour. The South African artist Simon Gush has shifted from this trend in order to present labour without directly representing the workers. In his artwork there is no longer a search for the political subject as a historical force or for the individuals who occupied its place; instead he leads viewers to a critical reading of an object, allowing a staging of the past from the viewpoint of the present. That is what I think Red does. In this article I explore Gush's connections with Marx, Benjamin and Steyerl to show how Gush's work is part of a critical tradition that has abandoned the subject as the privileged instance of political agency; turning the emphasis of the modern schema upside down, it focuses on the object as the force of emancipation. I would like to suggest that Gush used an object, Mandela's red Mercedes-Benz, to produce another image so that the story told is not necessarily that of a symbol of pacification, but one in which the factory was a battlefield. In this way I explore the emancipatory potencies of the object. What I propose is a reading of Red from the point of view of a return to the thing, where the latter becomes a political force.

  10. Physics opportunities for a B Factory

    International Nuclear Information System (INIS)

    Quinn, H.R.

    1992-02-01

    In the short time allotted for this talk it is not possible to review all the physics opportunities offered by a B Factory. I focus on the physics of CP Violation and the resulting tests of the Standard Model

  11. Benthic carbonate factories of the Phanerozoic

    NARCIS (Netherlands)

    Schlager, W.

    2003-01-01

    Marine carbonate precipitation occurs in three basic modes: abiotic (or quasi-abiotic), biotically induced, and biotically controlled. On a geologic scale, these precipitation modes combine to form three carbonate production systems, or "factories" in the benthic environment: (1) tropical

  12. The physics of the B factories

    CERN Document Server

    Bevan, A J; Mannel, Th; Prell, S; Yabsley, B D; Abe, K; Aihara, H; Anulli, F; Arnaud, N; Aushev, T; Beneke, M; Beringer, J; Bianchi, F; Bigi, I I; Bona, M; Brambilla, N; Brodzicka, J; Chang, P; Charles, M J; Cheng, C H; Cheng, H -Y; Chistov, R; Colangelo, P; Coleman, J P; Drutskoy, A; Druzhinin, V P; Eidelman, S; Eigen, G; Eisner, A M; Faccini, R; Flood, K T; Gambino, P; Gaz, A; Gradl, W; Hayashii, H; Higuchi, T; Hulsbergen, W D; Hurth, T; Iijima, T; Itoh, R; Jackson, P D; Kass, R; Kolomensky, Yu G; Kou, E; Križan, P; Kronfeld, A; Kumano, S; Kwon, Y J; Latham, T E; Leith, D W G S; Lüth, V; Martinez-Vidal, F; Meadows, B T; Mussa, R; Nakao, M; Nishida, S; Ocariz, J; Olsen, S L; Pakhlov, P; Pakhlova, G; Palano, A; Pich, A; Playfer, S; Poluektov, A; Porter, F C; Robertson, S H; Roney, J M; Roodman, A; Sakai, Y; Schwanda, C; Schwartz, A J; Seidl, R; Sekula, S J; Steinhauser, M; Sumisawa, K; Swanson, E S; Tackmann, F; Trabelsi, K; Uehara, S; Uno, S; van der Water, R; Vasseur, G; Verkerke, W; Waldi, R; Wang, M Z; Wilson, F F; Zupan, J; Zupanc, A; Adachi, I; Albert, J; Banerjee, Sw; Ben-Haim, E; Biassoni, P; Cahn, R N; Cartaro, C; Chauveau, J; Chen, C; Chiang, C C; Cowan, R; Dalseno, J; Davier, M; Davies, C; Dingfelder, J C; Echenard, B; Epifanov, D; Fulsom, B G; Gabareen, A M; Gary, J W; Godang, R; Graham, M T; Hafner, A; Hamilton, B; Hartmann, T; Hayasaka, K; Hearty, C; Iwasaki, Y; Khodjamirian, A; Kusaka, A; Kuzmin, A; Lafferty, G D; Lazzaro, A; Li, J; Lindemann, D; Long, O; Lusiani, A; Marchiori, G; Martinelli, M; Miyabayashi, K; Mizuk, R; Mohanty, G B; Muller, D R; Nakazawa, H; Ongmongkolkul, P; Pacetti, S; Palombo, F; Pedlar, T K; Piilonen, L E; Pilloni, A; Poireau, V; Prothmann, K; Pulliam, T; Rama, M; Ratcliff, B N; Roudeau, P; Schrenk, S; Schroeder, T; Schubert, K R; Shen, C P; Shwartz, B; Soffer, A; Solodov, E P; Somov, A; Starič, M; Stracka, S; Telnov, A V; Todyshev, K Yu; Tsuboyama, T; Uglov, T; Vinokurova, A; Walsh, J J; Watanabe, Y; Won, E; Wormser, G; Wright, D H; Ye, S; Zhang, C C; Abachi, S; Abashian, A; Abe, N; Abe, R; Abe, T; Abrams, G S; Adam, I; Adamczyk, K; Adametz, A; Adye, T; Agarwal, A; Ahmed, H; Ahmed, M; Ahmed, S; Ahn, B S; Ahn, H S; Aitchison, I J R; Akai, K; Akar, S; Akatsu, M; Akemoto, M; Akhmetshin, R; Akre, R; Alam, M S; Albert, J N; Aleksan, R; Alexander, J P; Alimonti, G; Allen, M T; Allison, J; Allmendinger, T; Alsmiller, J R G; Altenburg, D; Alwyn, K E; An, Q; Anderson, J; Andreassen, R; Andreotti, D; Andreotti, M; Andress, J C; Angelini, C; Anipko, D; Anjomshoaa, A; Anthony, P L; Antillon, E A; Antonioli, E; Aoki, K; Arguin, J F; A, K; Arisaka, K; Asai, K; Asai, M; Asano, Y; Asgeirsson, D J; Asner, D M; Aso, T; Aspinwall, M L; Aston, D; Atmacan, H; Aubert, B; Aulchenko, V; Ayad, R; Azemoon, T; Aziz, T; Azzolini, V; Azzopardi, D E; Baak, M A; Back, J J; Bagnasco, S; Bahinipati, S; Bailey, D S; Bailey, S; Bailly, P; van Bakel, N; Bakich, A M; Bala, A; Balagura, V; Baldini-Ferroli, R; Ban, Y; Banas, E; Band, H R; Banerjee, S; Baracchini, E; Barate, R; Barberio, E; Barbero, M; Bard, D J; Barillari, T; Barlow, N R; Barlow, R J; Barrett, M; Bartel, W; Bartelt, J; Bartoldus, R; Batignani, G; Battaglia, M; Bauer, J M; Bay, A; Beaulieu, M; Bechtle, P; Beck, T W; Becker, J; Becla, J; Bedny, I; Behari, S; Behera, P K; Behn, E; Behr, L; Beigbeder, C; Beiline, D; Bell, R; Bellini, F; Bellis, M; Bellodi, G; Belous, K; Benayoun, M; Benelli, G; Benitez, J F; Benkebil, M; Berger, N; Bernabeu, J; Bernard, D; Bernet, R; Bernlochner, F U; Berryhill, J W; Bertsche, K; Besson, P; Best, D S; Bettarini, S; Bettoni, D; Bhardwaj, V; Bhimji, W; Bhuyan, B; Biagini, M E; Biasini, M; van Bibber, K; Biesiada, J; Bingham, I; Bionta, R M; Bischofberger, M; Bitenc, U; Bizjak, I; Blanc, F; Blaylock, G; Blinov, V E; Bloom, E; Bloom, P C; Blount, N L; Blouw, J; Bly, M; Blyth, S; Boeheim, C T; Bomben, M; Bondar, A; Bondioli, M; Bonneaud, G R; Bonvicini, G; Booke, M; Booth, J; Borean, C; Borgland, A W; Borsato, E; Bosi, F; Bosisio, L; Botov, A A; Bougher, J; Bouldin, K; Bourgeois, P; Boutigny, D; Bowerman, D A; Boyarski, A M; Boyce, R F; Boyd, J T; Bozek, A; Bozzi, C; Bračko, M; Brandenburg, G; Brandt, T; Brau, B; Brau, J; Breon, A B; Breton, D; Brew, C; Briand, H; Bright-Thomas, P G; Brigljević, V; Britton, D I; Brochard, F; Broomer, B; Brose, J; Browder, T E; Brown, C L; Brown, C M; Brown, D N; Browne, M; Bruinsma, M; Brunet, S; Bucci, F; Buchanan, C; Buchmueller, O L; Bünger, C; Bugg, W; Bukin, A D; Bula, R; Bulten, H; Burchat, P R; Burgess, W; Burke, J P; Button-Shafer, J; Buzykaev, A R; Buzzo, A; Cai, Y; Calabrese, R; Calcaterra, A; Calderini, G; Camanzi, B; Campagna, E; Campagnari, C; Capra, R; Carassiti, V; Carpinelli, M; Carroll, M; Casarosa, G; Casey, B C K; Cason, N M; Castelli, G; Cavallo, N; Cavoto, G; Cecchi, A; Cenci, R; Cerizza, G; Cervelli, A; Ceseracciu, A; Chai, X; Chaisanguanthum, K S; Chang, M C; Chang, Y H; Chang, Y W; Chao, D S; Chao, M; Chao, Y; Charles, E; Chavez, C A; Cheaib, R; Chekelian, V; Chen, A; Chen, E; Chen, G P; Chen, H F; Chen, J -H; Chen, J C; Chen, K F; Chen, P; Chen, S; Chen, W T; Chen, X; Chen, X R; Chen, Y Q; Cheng, B; Cheon, B G; Chevalier, N; Chia, Y M; Chidzik, S; Chilikin, K; Chistiakova, M V; Cizeron, R; Cho, I S; Cho, K; Chobanova, V; Choi, H H F; Choi, K S; Choi, S K; Choi, Y; Choi, Y K; Christ, S; Chu, P H; Chun, S; Chuvikov, A; Cibinetto, G; Cinabro, D; Clark, A R; Clark, P J; Clarke, C K; Claus, R; Claxton, B; Clifton, Z C; Cochran, J; Cohen-Tanugi, J; Cohn, H; Colberg, T; Cole, S; Colecchia, F; Condurache, C; Contri, R; Convert, P; Convery, M R; Cooke, P; Copty, N; Cormack, C M; Corso, F Dal; Corwin, L A; Cossutti, F; Cote, D; Ramusino, A Cotta; Cottingham, W N; Couderc, F; Coupal, D P; Covarelli, R; Cowan, G; Craddock, W W; Crane, G; Crawley, H B; Cremaldi, L; Crescente, A; Cristinziani, M; Crnkovic, J; Crosetti, G; Cuhadar-Donszelmann, T; Cunha, A; Curry, S; D'Orazio, A; Dû, S; Dahlinger, G; Dahmes, B; Dallapiccola, C; Danielson, N; Danilov, M; Das, A; Dash, M; Dasu, S; Datta, M; Daudo, F; Dauncey, P D; David, P; Davis, C L; Day, C T; De Mori, F; De Domenico, G; De Groot, N; De la Vaissière, C; de la Vaissière, Ch; de Lesquen, A; De Nardo, G; de Sangro, R; De Silva, A; DeBarger, S; Decker, F J; Sanchez, P del Amo; Del Buono, L; Del Gamba, V; del Re, D; Della Ricca, G; Denig, A G; Derkach, D; Derrington, I M; DeStaebler, H; Destree, J; Devmal, S; Dey, B; Di Girolamo, B; Di Marco, E; Dickopp, M; Dima, M O; Dittrich, S; Dittongo, S; Dixon, P; Dneprovsky, L; Dohou, F; Doi, Y; Doležal, Z; Doll, D A; Donald, M; Dong, L; Dong, L Y; Dorfan, J; Dorigo, A; Dorsten, M P; Dowd, R; Dowdell, J; Drásal, Z; Dragic, J; Drummond, B W; Dubitzky, R S; Dubois-Felsmann, G P; Dubrovin, M S; Duh, Y C; Duh, Y T; Dujmic, D; Dungel, W; Dunwoodie, W; Dutta, D; Dvoretskii, A; Dyce, N; Ebert, M; Eckhart, E A; Ecklund, S; Eckmann, R; Eckstein, P; Edgar, C L; Edwards, A J; Egede, U; Eichenbaum, A M; Elmer, P; Emery, S; Enari, Y; Enomoto, R; Erdos, E; Erickson, R; Ernst, J A; Erwin, R J; Escalier, M; Eschenburg, V; Eschrich, I; Esen, S; Esteve, L; Evangelisti, F; Everton, C W; Eyges, V; Fabby, C; Fabozzi, F; Fahey, S; Falbo, M; Fan, S; Fang, F; Fanin, C; Farbin, A; Farhat, H; Fast, J E; Feindt, M; Fella, A; Feltresi, E; Ferber, T; Fernholz, R E; Ferrag, S; Ferrarotto, F; Ferroni, F; Field, R C; Filippi, A; Finocchiaro, G; Fioravanti, E; da Costa, J Firmino; Fischer, P -A; Fisher, A; Fisher, P H; Flacco, C J; Flack, R L; Flaecher, H U; Flanagan, J; Flanigan, J M; Ford, K E; Ford, W T; Forster, I J; Forti, A C; Forti, F; Fortin, D; Foster, B; Foulkes, S D; Fouque, G; Fox, J; Franchini, P; Sevilla, M Franco; Franek, B; Frank, E D; Fransham, K B; Fratina, S; Fratini, K; Frey, A; Frey, R; Friedl, M; Fritsch, M; Fry, J R; Fujii, H; Fujikawa, M; Fujita, Y; Fujiyama, Y; Fukunaga, C; Fukushima, M; Fullwood, J; Funahashi, Y; Funakoshi, Y; Furano, F; Furman, M; Furukawa, K; Futterschneider, H; Gabathuler, E; Gabriel, T A; Gabyshev, N; Gaede, F; Gagliardi, N; Gaidot, A; Gaillard, J -M; Gaillard, J R; Galagedera, S; Galeazzi, F; Gallo, F; Gamba, D; Gamet, R; Gan, K K; Gandini, P; Ganguly, S; Ganzhur, S F; Gao, Y Y; Gaponenko, I; Garmash, A; Tico, J Garra; Garzia, I; Gaspero, M; Gastaldi, F; Gatto, C; Gaur, V; Geddes, N I; Geld, T L; Genat, J -F; George, K A; George, M; George, S; Georgette, Z; Gershon, T J; Gill, M S; Gillard, R; Gilman, J D; Giordano, F; Giorgi, M A; Giraud, P -F; Gladney, L; Glanzman, T; Glattauer, R; Go, A; Goetzen, K; Goh, Y M; Gokhroo, G; Goldenzweig, P; Golubev, V B; Gopal, G P; Gordon, A; Gorišek, A; Goriletsky, V I; Gorodeisky, R; Gosset, L; Gotow, K; Gowdy, S J; Graffin, P; Grancagnolo, S; Grauges, E; Graziani, G; Green, M G; Greene, M G; Grenier, G J; Grenier, P; Griessinger, K; Grillo, A A; Grinyov, B V; Gritsan, A V; Grosdidier, G; Perdekamp, M Grosse; Grosso, P; Grothe, M; Groysman, Y; Grünberg, O; Guido, E; Guler, H; Gunawardane, N J W; Guo, Q H; Guo, R S; Guo, Z J; Guttman, N; Ha, H; Ha, H C; Haas, T; Haba, J; Hachtel, J; Hadavand, H K; Hadig, T; Hagner, C; Haire, M; Haitani, F; Haji, T; Haller, G; Halyo, V; Hamano, K; Hamasaki, H; de Monchenault, G Hamel; Hamilton, J; Hamilton, R; Hamon, O; Han, B Y; Han, Y L; Hanada, H; Hanagaki, K; Handa, F; Hanson, J E; Hanushevsky, A; Hara, K; Hara, T; Harada, Y; Harrison, P F; Harrison, T J; Harrop, B; Hart, A J; Hart, P A; Hartfiel, B L; Harton, J L; Haruyama, T; Hasan, A; Hasegawa, Y; Hast, C; Hastings, N C; Hasuko, K; Hauke, A; Hawkes, C M; Hayashi, K; Hazumi, M; Hee, C; Heenan, E M; Heffernan, D; Held, T; Henderson, R; Henderson, S W; Hertzbach, S S; Hervé, S; Heß, M; Heusch, C A; Hicheur, A; Higashi, Y; Higasino, Y; Higuchi, I; Hikita, S; Hill, E J; Himel, T; Hinz, L; Hirai, T; Hirano, H; Hirschauer, J F; Hitlin, D G; Hitomi, N; Hodgkinson, M C; Höcker, A; Hoi, C T; Hojo, T; Hokuue, T; Hollar, J J; Hong, T M; Honscheid, K; Hooberman, B; Hopkins, D A; Horii, Y; Hoshi, Y; Hoshina, K; Hou, S; Hou, W S; Hryn'ova, T; Hsiung, Y B; Hsu, C L; Hsu, S C; Hu, H; Hu, T; Huang, H C; Huang, T J; Huang, Y C; Huard, Z; Huffer, M E; Hufnagel, D; Hung, T; Hutchcroft, D E; Hyun, H J; Ichizawa, S; Igaki, T; Igarashi, A; Igarashi, S; Igarashi, Y; Igonkina, O; Ikado, K; Ikeda, H; Ikeda, K; Ilic, J; Inami, K; Innes, W R; Inoue, Y; Ishikawa, A; Ishino, H; Itagaki, K; Itami, S; Itoh, K; Ivanchenko, V N; Iverson, R; Iwabuchi, M; Iwai, G; Iwai, M; Iwaida, S; Iwamoto, M; Iwasaki, H; Iwasaki, M; Iwashita, T; Izen, J M; Jackson, D J; Jackson, F; Jackson, G; Jackson, P S; Jacobsen, R G; Jacoby, C; Jaegle, I; Jain, V; Jalocha, P; Jang, H K; Jasper, H; Jawahery, A; Jayatilleke, S; Jen, C M; Jensen, F; Jessop, C P; Ji, X B; John, M J J; Johnson, D R; Johnson, J R; Jolly, S; Jones, M; Joo, K K; Joshi, N; Joshi, N J; Judd, D; Julius, T; Kadel, R W; Kadyk, J A; Kagan, H; Kagan, R; Kah, D H; Kaiser, S; Kaji, H; Kajiwara, S; Kakuno, H; Kameshima, T; Kaminski, J; Kamitani, T; Kaneko, J; Kang, J H; Kang, J S; Kani, T; Kapusta, P; Karbach, T M; Karolak, M; Karyotakis, Y; Kasami, K; Katano, G; Kataoka, S U; Katayama, N; Kato, E; Kato, Y; Kawai, H; Kawai, M; Kawamura, N; Kawasaki, T; Kay, J; Kay, M; Kelly, M P; Kelsey, M H; Kent, N; Kerth, L T; Khan, A; Khan, H R; Kharakh, D; Kibayashi, A; Kichimi, H; Kiesling, C; Kikuchi, M; Kikutani, E; Kim, B H; Kim, C H; Kim, D W; Kim, H; Kim, H J; Kim, H O; Kim, H W; Kim, J B; Kim, J H; Kim, K T; Kim, M J; Kim, P; Kim, S K; Kim, S M; Kim, T H; Kim, Y I; Kim, Y J; King, G J; Kinoshita, K; Kirk, A; Kirkby, D; Kitayama, I; Klemetti, M; Klose, V; Klucar, J; Knecht, N S; Knoepfel, K J; Knowles, D J; Ko, B R; Kobayashi, N; Kobayashi, S; Kobayashi, T; Kobel, M J; Koblitz, S; Koch, H; Kocian, M L; Kodyš, P; Koeneke, K; Kofler, R; Koike, S; Koishi, S; Koiso, H; Kolb, J A; Kolya, S D; Kondo, Y; Konishi, H; Koppenburg, P; Koptchev, V B; Kordich, T M B; Korol, A A; Korotushenko, K; Korpar, S; Kouzes, R T; Kovalskyi, D; Kowalewski, R; Kozakai, Y; Kozanecki, W; Kral, J F; Krasnykh, A; Krause, R; Kravchenko, E A; Krebs, J; Kreisel, A; Kreps, M; Krishnamurthy, M; Kroeger, R; Kroeger, W; Krokovny, P; Kronenbitter, B; Kroseberg, J; Kubo, T; Kuhr, T; Kukartsev, G; Kulasiri, R; Kulikov, A; Kumar, R; Kumar, S; Kumita, T; Kuniya, T; Kunze, M; Kuo, C C; Kuo, T -L; Kurashiro, H; Kurihara, E; Kurita, N; Kuroki, Y; Kurup, A; Kutter, P E; Kuznetsova, N; Kvasnička, P; Kyberd, P; Kyeong, S H; Lacker, H M; Lae, C K; Lamanna, E; Lamsa, J; Lanceri, L; Landi, L; Lang, M I; Lange, D J; Lange, J S; Langenegger, U; Langer, M; Lankford, A J; Lanni, F; Laplace, S; Latour, E; Lau, Y P; Lavin, D R; Layter, J; Lebbolo, H; LeClerc, C; Leddig, T; Leder, G; Diberder, F Le; Lee, C L; Lee, J; Lee, J S; Lee, M C; Lee, M H; Lee, M J; Lee, S -J; Lee, S E; Lee, S H; Lee, Y J; Lees, J P; Legendre, M; Leitgab, M; Leitner, R; Leonardi, E; Leonidopoulos, C; Lepeltier, V; Leruste, Ph; Lesiak, T; Levi, M E; Levy, S L; Lewandowski, B; Lewczuk, M J; Lewis, P; Li, H; Li, H B; Li, S; Li, X; Li, Y; Gioi, L Li; Libby, J; Lidbury, J; Lillard, V; Lim, C L; Limosani, A; Lin, C S; Lin, J Y; Lin, S W; Lin, Y S; Lindquist, B; Lindsay, C; Lista, L; Liu, C; Liu, F; Liu, H; Liu, H M; Liu, J; Liu, R; Liu, T; Liu, Y; Liu, Z Q; Liventsev, D; Vetere, M Lo; Locke, C B; Lockman, W S; Di Lodovico, F; Lombardo, V; London, G W; Pegna, D Lopes; Lopez, L; Lopez-March, N; Lory, J; LoSecco, J M; Lou, X C; Louvot, R; Lu, A; Lu, C; Lu, M; Lu, R S; Lueck, T; Luitz, S; Lukin, P; Lund, P; Luppi, E; Lutz, A M; Lutz, O; Lynch, G; Lynch, H L; Lyon, A J; Lyubinsky, V R; MacFarlane, D B; Mackay, C; MacNaughton, J; Macri, M M; Madani, S; Mader, W F; Majewski, S A; Majumder, G; Makida, Y; Malaescu, B; Malaguti, R; Malclès, J; Mallik, U; Maly, E; Mamada, H; Manabe, A; Mancinelli, G; Mandelkern, M; Mandl, F; Manfredi, P F; Mangeol, D J J; Manoni, E; Mao, Z P; Margoni, M; Marker, C E; Markey, G; Marks, J; Marlow, D; Marques, V; Marsiske, H; Martellotti, S; Martin, E C; Martin, J P; Martin, L; Martinez, A J; Marzolla, M; Mass, A; Masuzawa, M; Mathieu, A; Matricon, P; Matsubara, T; Matsuda, T; Matsumoto, H; Matsumoto, S; Matsumoto, T; Matsuo, H; Mattison, T S; Matvienko, D; Matyja, A; Mayer, B; Mazur, M A; Mazzoni, M A; McCulloch, M; McDonald, J; McFall, J D; McGrath, P; McKemey, A K; McKenna, J A; Mclachlin, S E; McMahon, S; McMahon, T R; McOnie, S; Medvedeva, T; Melen, R; Mellado, B; Menges, W; Menke, S; Merchant, A M; Merkel, J; Messner, R; Metcalfe, S; Metzler, S; Meyer, N T; Meyer, T I; Meyer, W T; Michael, A K; Michelon, G; Michizono, S; Micout, P; Miftakov, V; Mihalyi, A; Mikami, Y; Milanes, D A; Milek, M; Mimashi, T; Minamora, J S; Mindas, C; Minutoli, S; Mir, L M; Mishra, K; Mitaroff, W; Miyake, H; Miyashita, T S; Miyata, H; Miyazaki, Y; Moffitt, L C; Mohapatra, A; Mohapatra, A K; Mohapatra, D; Moll, A; Moloney, G R; Mols, J P; Mommsen, R K; Monge, M R; Monorchio, D; Moore, T B; Moorhead, G F; de Freitas, P Mora; Morandin, M; Morgan, N; Morgan, S E; Morganti, M; Morganti, S; Mori, S; Mori, T; Morii, M; Morris, J P; Morsani, F; Morton, G W; Moss, L J; Mouly, J P; Mount, R; Mueller, J; Müller-Pfefferkorn, R; Mugge, M; Muheim, F; Muir, A; Mullin, E; Munerato, M; Murakami, A; Murakami, T; Muramatsu, N; Musico, P; Nagai, I; Nagamine, T; Nagasaka, Y; Nagashima, Y; Nagayama, S; Nagel, M; Naisbit, M T; Nakadaira, T; Nakahama, Y; Nakajima, M; Nakajima, T; Nakamura, I; Nakamura, T; Nakamura, T T; Nakano, E; Nakayama, H; Nam, J W; Narita, S; Narsky, I; Nash, J A; Natkaniec, Z; Nauenberg, U; Nayak, M; Neal, H; Nedelkovska, E; Negrini, M; Neichi, K; Nelson, D; Nelson, S; Neri, N; Nesom, G; Neubauer, S; Newman-Coburn, D; Ng, C; Nguyen, X; Nicholson, H; Niebuhr, C; Nief, J Y; Niiyama, M; Nikolich, M B; Nisar, N K; Nishimura, K; Nishio, Y; Nitoh, O; Nogowski, R; Noguchi, S; Nomura, T; Nordby, M; Nosochkov, Y; Novokhatski, A; Nozaki, S; Nozaki, T; Nugent, I M; O'Grady, C P; O'Neale, S W; O'Neill, F G; Oberhof, B; Oddone, P J; Ofte, I; Ogawa, A; Ogawa, K; Ogawa, S; Ogawa, Y; Ohkubo, R; Ohmi, K; Ohnishi, Y; Ohno, F; Ohshima, T; Ohshima, Y; Ohuchi, N; Oide, K; Oishi, N; Okabe, T; Okazaki, N; Okazaki, T; Okuno, S; Olaiya, E O; Olivas, A; Olley, P; Olsen, J; Ono, S; Onorato, G; Onuchin, A P; Onuki, Y; Ooba, T; Orimoto, T J; Oshima, T; Osipenkov, I L; Ostrowicz, W; Oswald, C; Otto, S; Oyang, J; Oyanguren, A; Ozaki, H; Ozcan, V E; Paar, H P; Padoan, C; Paick, K; Palka, H; Pan, B; Pan, Y; Vazquez, W Panduro; Panetta, J; Panova, A I; Panvini, R S; Panzenböck, E; Paoloni, E; Paolucci, P; Pappagallo, M; Paramesvaran, S; Park, C S; Park, C W; Park, H; Park, H K; Park, K S; Park, W; Parry, R J; Parslow, N; Passaggio, S; Pastore, F C; Patel, P M; Patrignani, C; Patteri, P; Pavel, T; Pavlovich, J; Payne, D J; Peak, L S; Peimer, D R; Pelizaeus, M; Pellegrini, R; Pelliccioni, M; Peng, C C; Peng, J C; Peng, K C; Peng, T; Penichot, Y; Pennazzi, S; Pennington, M R; Penny, R C; Penzkofer, A; Perazzo, A; Perez, A; Perl, M; Pernicka, M; Perroud, J -P; Peruzzi, I M; Pestotnik, R; Peters, K; Peters, M; Petersen, B A; Petersen, T C; Petigura, E; Petrak, S; Petrella, A; Petrič, M; Petzold, A; Pia, M G; Piatenko, T; Piccolo, D; Piccolo, M; Piemontese, L; Piemontese, M; Pierini, M; Pierson, S; Pioppi, M; Piredda, G; Pivk, M; Plaszczynski, S; Polci, F; Pompili, A; Poropat, P; Posocco, M; Potter, C T; Potter, R J L; Prasad, V; Prebys, E; Prencipe, E; Prendki, J; Prepost, R; Prest, M; Prim, M; Pripstein, M; Prudent, X; Pruvot, S; Puccio, E M T; Purohit, M V; Qi, N D; Quinn, H; Raaf, J; Rabberman, R; Raffaelli, F; Ragghianti, G; Rahatlou, S; Rahimi, A M; Rahmat, R; Rakitin, A Y; Randle-Conde, A; Rankin, P; Rashevskaya, I; Ratkovsky, S; Raven, G; Re, V; Reep, M; Regensburger, J J; Reidy, J; Reif, R; Reisert, B; Renard, C; Renga, F; Ricciardi, S; Richman, J D; Ritchie, J L; Ritter, M; Rivetta, C; Rizzo, G; Roat, C; Robbe, P; Roberts, D A; Robertson, A I; Robutti, E; Rodier, S; Rodriguez, D M; Rodriguez, J L; Rodriguez, R; Roe, N A; Röhrken, M; Roethel, W; Rolquin, J; Romanov, L; Romosan, A; Ronan, M T; Rong, G; Ronga, F J; Roos, L; Root, N; Rosen, M; Rosenberg, E I; Rossi, A; Rostomyan, A; Rotondo, M; Roussot, E; Roy, J; Rozanska, M; Rozen, Y; Rubin, A E; Ruddick, W O; Ruland, A M; Rybicki, K; Ryd, A; Ryu, S; Ryuko, J; Sabik, S; Sacco, R; Saeed, M A; Tehrani, F Safai; Sagawa, H; Sahoo, H; Sahu, S; Saigo, M; Saito, T; Saitoh, S; Sakai, K; Sakamoto, H; Sakaue, H; Saleem, M; Salnikov, A A; Salvati, E; Salvatore, F; Samuel, A; Sanders, D A; Sanders, P; Sandilya, S; Sandrelli, F; Sands, W; Sands, W R; Sanpei, M; Santel, D; Santelj, L; Santoro, V; Santroni, A; Sanuki, T; Sarangi, T R; Saremi, S; Sarti, A; Sasaki, T; Sasao, N; Satapathy, M; Sato, Nobuhiko; Sato, Noriaki; Sato, Y; Satoyama, N; Satpathy, A; Savinov, V; Savvas, N; Saxton, O H; Sayeed, K; Schaffner, S F; Schalk, T; Schenk, S; Schieck, J R; Schietinger, T; Schilling, C J; Schindler, R H; Schmid, S; Schmitz, R E; Schmuecker, H; Schneider, O; Schnell, G; Schönmeier, P; Schofield, K C; Schott, G; Schröder, H; Schram, M; Schubert, J; Schümann, J; Schultz, J; Schumm, B A; Schune, M H; Schwanke, U; Schwarz, H; Schwiening, J; Schwierz, R; Schwitters, R F; Sciacca, C; Sciolla, G; Scott, I J; Seeman, J; Seiden, A; Seitz, R; Seki, T; Sekiya, A I; Semenov, S; Semmler, D; Sen, S; Senyo, K; Seon, O; Serbo, V V; Serednyakov, S I; Serfass, B; Serra, M; Serrano, J; Settai, Y; Seuster, R; Sevior, M E; Shakhova, K V; Shang, L; Shapkin, M; Sharma, V; Shebalin, V; Shelkov, V G; Shen, B C; Shen, D Z; Shen, Y T; Sherwood, D J; Shibata, T; Shibata, T A; Shibuya, H; Shidara, T; Shimada, K; Shimoyama, M; Shinomiya, S; Shiu, J G; Shorthouse, H W; Shpilinskaya, L I; Sibidanov, A; Sicard, E; Sidorov, A; Sidorov, V; Siegle, V; Sigamani, M; Simani, M C; Simard, M; Simi, G; Simon, F; Simonetto, F; Sinev, N B; Singh, H; Singh, J B; Sinha, R; Sitt, S; Skovpen, Yu I; Sloane, R J; Smerkol, P; Smith, A J S; Smith, D; Smith, D S; Smith, J G; Smol, A; Snoek, H L; Snyder, A; So, R Y; Sobie, R J; Soderstrom, E; Soha, A; Sohn, Y S; Sokoloff, M D; Sokolov, A; Solagna, P; Solovieva, E; Soni, N; Sonnek, P; Sordini, V; Spaan, B; Spanier, S M; Spencer, E; Speziali, V; Spitznagel, M; Spradlin, P; Staengle, H; Stamen, R; Stanek, M; Stanič, S; Stark, J; Steder, M; Steininger, H; Steinke, M; Stelzer, J; Stevanato, E; Stocchi, A; Stock, R; Stoeck, H; Stoker, D P; Stroili, R; Strom, D; Strother, P; Strube, J; Stugu, B; Stypula, J; Su, D; Suda, R; Sugahara, R; Sugi, A; Sugimura, T; Sugiyama, A; Suitoh, S; Sullivan, M K; Sumihama, M; Sumiyoshi, T; Summers, D J; Sun, L; Sun, S; Sundermann, J E; Sung, H F; Susaki, Y; Sutcliffe, P; Suzuki, A; Suzuki, J; Suzuki, J I; Suzuki, K; Suzuki, S; Suzuki, S Y; Swain, J E; Swain, S K; T'Jampens, S; Tabata, M; Tackmann, K; Tajima, H; Tajima, O; Takahashi, K; Takahashi, S; Takahashi, T; Takasaki, F; Takayama, T; Takita, M; Tamai, K; Tamponi, U; Tamura, N; Tan, N; Tan, P; Tanabe, K; Tanabe, T; Tanaka, H A; Tanaka, J; Tanaka, M; Tanaka, S; Tanaka, Y; Tanida, K; Taniguchi, N; Taras, P; Tasneem, N; Tatishvili, G; Tatomi, T; Tawada, M; Taylor, F; Taylor, G N; Taylor, G P; Telnov, V I; Teodorescu, L; Ter-Antonyan, R; Teramoto, Y; Teytelman, D; Thérin, G; Thiebaux, Ch; Thiessen, D; Thomas, E W; Thompson, J M; Thorne, F; Tian, X C; Tibbetts, M; Tikhomirov, I; Tinslay, J S; Tiozzo, G; Tisserand, V; Tocut, V; Toki, W H; Tomassini, E W; Tomoto, M; Tomura, T; Torassa, E; Torrence, E; Tosi, S; Touramanis, C; Toussaint, J C; Tovey, S N; Trapani, P P; Treadwell, E; Triggiani, G; Trincaz-Duvoid, S; Trischuk, W; Troost, D; Trunov, A; Tsai, K L; Tsai, Y T; Tsujita, Y; Tsukada, K; Tsukamoto, T; Tuggle, J M; Tumanov, A; Tung, Y W; Turnbull, L; Turner, J; Turri, M; Uchida, K; Uchida, M; Uchida, Y; Ueki, M; Ueno, K; Ujiie, N; Ulmer, K A; Unno, Y; Urquijo, P; Ushiroda, Y; Usov, Y; Usseglio, M; Usuki, Y; Uwer, U; Va'vra, J; Vahsen, S E; Vaitsas, G; Valassi, A; Vallazza, E; Vallereau, A; Vanhoefer, P; van Hoek, W C; Van Hulse, C; van Winkle, D; Varner, G; Varnes, E W; Varvell, K E; Vasileiadis, G; Velikzhanin, Y S; Verderi, M; Versillé, S; Vervink, K; Viaud, B; Vidal, P B; Villa, S; Villanueva-Perez, P; Vinograd, E L; Vitale, L; Vitug, G M; Voß, C; Voci, C; Voena, C; Volk, A; von Wimmersperg-Toeller, J H; Vorobyev, V; Vossen, A; Vuagnin, G; Vuosalo, C O; Wacker, K; Wagner, A P; Wagner, D L; Wagner, G; Wagner, M N; Wagner, S R; Wagoner, D E; Walker, D; Walkowiak, W; Wallom, D; Wang, C C; Wang, C H; Wang, J; Wang, J G; Wang, K; Wang, L; Wang, L L; Wang, P; Wang, T J; Wang, W F; Wang, X L; Wang, Y F; Wappler, F R; Watanabe, M; Watson, A T; Watson, J E; Watson, N K; Watt, M; Weatherall, J H; Weaver, M; Weber, T; Wedd, R; Wei, J T; Weidemann, A W; W, A J R; Wenzel, W A; West, C A; West, C G; West, T J; White, R M; Wicht, J; Widhalm, L; Wiechczynski, J; Wienands, U; Wilden, L; Wilder, M; Williams, D C; Williams, G; Williams, J C; Williams, K M; Williams, M I; Willocq, S Y; Wilson, J R; Wilson, M G; Wilson, R J; Winklmeier, F; Winter, M A; Wisniewski, W J; Wittgen, M; Wittlin, J; Wittmer, W; Wixted, R; Woch, A; Wogsland, B J; Wong, Q K; Wray, B C; Wren, A C; Wright, D M; Wu, C H; Wu, J; Wu, S L; Wulsin, H W; Xella, S M; Xie, Q L; Xie, Y; Xu, Z Z; Yèche, Ch; Yamada, Y; Yamaga, M; Yamaguchi, A; Yamaguchi, H; Yamaki, T; Yamamoto, H; Yamamoto, N; Yamamoto, R K; Yamamoto, S; Yamanaka, T; Yamaoka, H; Yamaoka, J; Yamaoka, Y; Yamashita, Y; Yamauchi, M; Yan, D S; Yan, Y; Yanai, H; Yanaka, S; Yang, H; Yang, R; Yang, S; Yarritu, A K; Yashchenko, S; Yashima, J; Yasin, Z; Yasu, Y; Ye, S W; Yeh, P; Yi, J I; Yi, K; Yi, M; Yin, Z W; Ying, J; Yocky, G; Yokoyama, K; Yokoyama, M; Yokoyama, T; Yoshida, K; Yoshida, M; Yoshimura, Y; Young, C C; Yu, C X; Yu, Z; Yuan, C Z; Yuan, Y; Yumiceva, F X; Yusa, Y; Yushkov, A N; Yuta, H; Zacek, V; Zain, S B; Zallo, A; Zambito, S; Zander, D; Zang, S L; Zanin, D; Zaslavsky, B G; Zeng, Q L; Zghiche, A; Zhang, B; Zhang, J; Zhang, L; Zhang, L M; Zhang, S Q; Zhang, Z P; Zhao, H W; Zhao, M; Zhao, Z G; Zheng, Y; Zheng, Y H; Zheng, Z P; Zhilich, V; Zhou, P; Zhu, R Y; Zhu, Y S; Zhu, Z M; Zhulanov, V; Ziegler, T; Ziegler, V; Zioulas, G; Zisman, M; Zito, M; Zürcher, D; Zwahlen, N; Zyukova, O; Živko, T; Žontar, D; Bevan, Adrian; Golob, Bostjan; Mannel, Thomas; Prell, Soeren; Yabsley, Bruce

    2014-01-01

    This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C.

  13. Tips for Reducing Pesticide Impacts on Wildlife

    Science.gov (United States)

    This Web page provides tips for pesticide users in residential and agricultural settings, as well as tips for certified pesticide applicators for ways to protect wildlife from potentially harmful effects of pesticides.

  14. 2011 EPA Pesticide General Permit (PGP)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The 2011 EPA Pesticide General Permit (PGP) covers discharges of biological pesticides, and chemical pesticides that leave a residue, in areas where EPA is the NPDES...

  15. Radiation induced microbial pesticide

    International Nuclear Information System (INIS)

    Kim, Ki Yup; Lee, Young Keun; Kim, Jae Sung; Kim, Jin Kyu; Lee, Sang Jae

    2000-01-01

    To control plant pathogenic fungi, 4 strains of bacteria (K1, K3, K4, YS1) were isolated from mushroom compost and hot spring. K4, K1, K3, YS1 strain showed wide antifungal spectrum and high antifungal activities against 13 kinds of fungi. Mutants of K1 and YS1 strains were induced by gamma-ray radiation and showed promising antifungal activities. These wild type and mutants showed resistant against more than 27 kinds of commercial pesticides among 30 kinds of commercial pesticides test particularly, YS1-1006 mutant strain showed resistant against hydrogen oxide. And mutants had increased antifungal activity against Botryoshaeria dothidea. These results suggested that radiation could be an useful method for the induction of functional mutants. (author)

  16. The geochemistry of pesticides

    Science.gov (United States)

    Barbash, Jack E.

    2007-01-01

    The mid-1970s marked a major turning point in human history, for it was at that moment that the ability of the Earth’s ecosystems to absorb most of the biological impacts of human activities appears to have been exceeded by the magnitude of those impacts. This conclusion is based partly upon estimates of the rate of carbon dioxide emission during the combustion of fossil fuels, relative to the rate of its uptake by terrestrial ecosystems (Loh, 2002). A very different threshold, however, had already been crossed several decades earlier with the birth of the modern chemical industry, which produced novel substances for which no such natural assimilative capacity existed. Among these new chemical compounds, none has posed a greater challenge to the planet’s ecosystems than synthetic pesticides, compounds that have been intentionally released into the hydrologic system in vast quantities—several hundred million pounds of active ingredient (a.i.) per year in the United States alone (Donaldson et al., 2002)—for many decades. To gauge the extent to which we are currently able to assess the environmental implications of this new development in the Earth’s history, this chapter presents an overview of current understanding regarding the sources, transport, fate, and biological effects of pesticides, their transformation products, and selected adjuvants in the hydrologic system. (Adjuvants are the so-called inert ingredients included in commercial pesticide formulations to enhance the effectiveness of the active ingredients.)

  17. Electronic Submissions of Pesticide Applications

    Science.gov (United States)

    Applications for pesticide registration can be submitted electronically, including forms, studies, and draft product labeling. Applicants need not submit multiple electronic copies of any pieces of their applications.

  18. Factorials of real negative and imaginary numbers - A new perspective.

    Science.gov (United States)

    Thukral, Ashwani K

    2014-01-01

    Presently, factorials of real negative numbers and imaginary numbers, except for zero and negative integers are interpolated using the Euler's gamma function. In the present paper, the concept of factorials has been generalised as applicable to real and imaginary numbers, and multifactorials. New functions based on Euler's factorial function have been proposed for the factorials of real negative and imaginary numbers. As per the present concept, the factorials of real negative numbers, are complex numbers. The factorials of real negative integers have their imaginary part equal to zero, thus are real numbers. Similarly, the factorials of imaginary numbers are complex numbers. The moduli of the complex factorials of real negative numbers, and imaginary numbers are equal to their respective real positive number factorials. Fractional factorials and multifactorials have been defined in a new perspective. The proposed concept has also been extended to Euler's gamma function for real negative numbers and imaginary numbers, and beta function.

  19. Analysis of scaled-factorial-moment data

    International Nuclear Information System (INIS)

    Seibert, D.

    1990-01-01

    We discuss the two standard constructions used in the search for intermittency, the exclusive and inclusive scaled factorial moments. We propose the use of a new scaled factorial moment that reduces to the exclusive moment in the appropriate limit and is free of undesirable multiplicity correlations that are contained in the inclusive moment. We show that there are some similarities among most of the models that have been proposed to explain factorial-moment data, and that these similarities can be used to increase the efficiency of testing these models. We begin by calculating factorial moments from a simple independent-cluster model that assumes only approximate boost invariance of the cluster rapidity distribution and an approximate relation among the moments of the cluster multiplicity distribution. We find two scaling laws that are essentially model independent. The first scaling law relates the moments to each other with a simple formula, indicating that the different factorial moments are not independent. The second scaling law relates samples with different rapidity densities. We find evidence for much larger clusters in heavy-ion data than in light-ion data, indicating possible spatial intermittency in the heavy-ion events

  20. Baby factories taint surrogacy in Nigeria.

    Science.gov (United States)

    Makinde, Olusesan Ayodeji; Makinde, Olufunmbi Olukemi; Olaleye, Olalekan; Brown, Brandon; Odimegwu, Clifford O

    2016-01-01

    The practice of reproductive medicine in Nigeria is facing new challenges with the proliferation of 'baby factories'. Baby factories are buildings, hospitals or orphanages that have been converted into places for young girls and women to give birth to children for sale on the black market, often to infertile couples, or into trafficking rings. This practice illegally provides outcomes (children) similar to surrogacy. While surrogacy has not been well accepted in this environment, the proliferation of baby factories further threatens its acceptance. The involvement of medical and allied health workers in the operation of baby factories raises ethical concerns. The lack of a properly defined legal framework and code of practice for surrogacy makes it difficult to prosecute baby factory owners, especially when they are health workers claiming to be providing services to clients. In this environment, surrogacy and other assisted reproductive techniques urgently require regulation in order to define when ethico-legal lines have been crossed in providing surrogacy or surrogacy-like services. Copyright © 2015 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

  1. Pesticide Program Dialogue Committee and Pesticide Regulatory Reform Meetings

    Science.gov (United States)

    EPA’s Office of Pesticide Programs will hold a public meeting of the Pesticide Program Dialogue Committee (PPDC) on Wednesday, May 3, from 9:00 a.m. to 4:45 p.m., and on Thursday, May 4, from 8:30 a.m. to noon.

  2. Evaluation System for Pesticides (ESPE). 1. Agricultural pesticides

    NARCIS (Netherlands)

    Emans HJB; Beek MA; Linders JBHJ

    1992-01-01

    In this report a risk assessment or evaluation system for agricultural pesticides is presented, which estimates the hazards for man and environment resulting from the use of these pesticides. The evaluation system has also been placed within the context of the Uniform System for the Evaluation of

  3. Tracer work in pesticide research

    International Nuclear Information System (INIS)

    Gonzales, B.P.

    1989-01-01

    Innumerable studies on the large number of pesticides being used throughout the world led to some adverse findings on the properties and behavior of these chemicals and their degradation products in revelation to potential toxicity and environmental pollution. However, it is also a fact (difficult to accept as it may) that the use of pesticides as an indirect means of increasing food production cannot yet be dispensed with despite the potential dangers attributed to it. What can be done is to insure its judicious application which means minimizing its effectiveness in controlling pest infestations. To be able to do this it is necessary to know not only what pesticide is to be used against a given pest but also the fate of pesticide after application to a particular environment under prevailing conditions. Knowledge of the distribution and persistence of the parent compounds under metabolites will also help either, to confirm or to dispel the alleged dangers posed by them. Radiotracer methodology is particularly effective for this type of work because it permits highly sensitive analysis with minimum clean-up and permits one to determine even the bound residues which defies ordinary extraction procedures. Some studies made are studies on fate of pesticides in plant after foliar application to plant needs, uptake and translocation of systemic pesticides, fate of pesticides in soil, bioaccumulation of pesticide by aquatic organisms, etc. This particular study is on distribution of pesticide among the components of a rice/fish ecosystem. This project aims to generate data from experiments conducted in a model ecosystem using radiolabelled lindane and carbo-furan. In both cases, results show a decline in extractable species from the recommended dosage of pesticide application although they tend to imbibe a considerable amount of pesticide. It is hoped that depuration in additional experiments will bring useful results. (Auth.)

  4. Pseudomonas putida as a microbial cell factory

    DEFF Research Database (Denmark)

    Wigneswaran, Vinoth

    for sustainable production of chemicals, which can be achieved by microbial cell factories. The work presented in this PhD thesis elucidates the application of Pseudomonas putida as a microbial cell factory for production of the biosurfactant rhamnolipid. The rhamnolipid production was achieved by heterologous...... phase. The genomic alterations were identified by genome sequencing and revealed parallel evolution. Glycerol was also shown to be able to support biofilm growth and as a result of this it can be used as an alternative substrate for producing biochemicals in conventional and biofilm reactors. The use...... of biofilm as a production platform and the usage of glycerol as a feedstock show the potential of using microbial cell factories in the transition toward sustainable production of chemicals. Particularly, the applicability of biofilm as a production platform can emerge as a promising alternative...

  5. Ergonomic analysis jobs in recovered factories.

    Science.gov (United States)

    Cuenca, Gabriela; Zotta, Gastón

    2012-01-01

    With the advent of the deep economic crisis in Argentina on 2001, the recovery of companies through to the creation of the Cooperatives Working Self-Management or Factories Recovered by its workers was constituted as one of the ways in which the salaried disobeyed the increasing unemployment. When the companies turn into recovered factories they tend to leave of side practices that have been seen like imposed by the previous organization and not understanding them as a primary condition for the execution of his tasks. Safety and ergonomics are two disciplines that are no longer considered relevant to the daily work. Therefore this investigation aims to revalue, undergo semantic to give back to a place in every organization analyzed. This research developed a self-diagnostic tool for working conditions, and the environment, present in the recovered factories.

  6. A conceptual design of circular Higgs factory

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yunhai

    2016-11-30

    Similar to a super B-factory, a circular Higgs factory (CHF) will require strong focusing systems near the interaction points and a low-emittance lattice in the arcs to achieve a factory luminosity. At electron beam energy of 125 GeV, beamstrahlung effects during the collision pose an additional challenge to the collider design. In particular, a large momentum acceptance at the 2% level is necessary to retain an adequate beam lifetime. This turns out to be the most challenging aspect in the design of a CHF. In this paper, an example will be provided to illustrate the beam dynamics in a CHF, emphasizing the chromatic optics. Basic optical modules and advanced analysis will be presented. Most importantly, we will show that 2% momentum aperture is achievable.

  7. Hadronic atoms at a kaon factory

    International Nuclear Information System (INIS)

    Leon, M.

    1982-01-01

    Beyond doubt, the advent of a kaon factory will be of immense significance for the study of hadronic atoms. Here we will discuss some classes of experiments that certainly can and will be done at a kaon factory, as well as some very interesting possibilities which deserve investigation. Among the certains we include the observation of hadronic x rays from kaonic and μ - atoms, for both Z greater than one and for the isotopes of hydrogen, mainly for strong interaction information. More conjectural is the possibility of measuring Xi - and Ω - x rays

  8. Nuclear physics at the KAON factory

    International Nuclear Information System (INIS)

    Kitching, R.

    1989-05-01

    The author surveys the range of nuclear physics issues which can be addressed with a high intensity hadron facility such as the KAON factory. He discusses hadron spectroscopy, kaon scattering, hypernuclear physics, spin physics, and nuclear physics with neutrinos. Nuclear Physics is defined rather broadly, encompassing the study of strongly interacting systems, and including the structure of individual hadrons, hadron-hadron interactions, hadronic weak and electromagnetic currents (in nuclei too), conventional nuclear structure, and exotic nuclei. The basic theme is how the KAON Factory can shed light on non-perturbative QCD and its relation to conventional nuclear physics

  9. Particle physics prospects for the KAON factory

    International Nuclear Information System (INIS)

    Bryman, D.

    1989-05-01

    The Kaon Factory at TRIUMF will produce beams of kaons, antiprotons, neutrinos and other particles with a hundred-fold increase in intensity over existing machines in the 30 GeV region. This will make possible new high precision experiments designed to test current ideas as well as high sensitivity measurements which could potentially reveal new effects. A sample of particle physics experiments involving rare kaon decays, CP and T violation studies, neutrino properties and reactions and light quark spectroscopy which might take advantage of the new opportunities presented by the Kaon Factory is discussed

  10. Choice of pesticide fate models

    International Nuclear Information System (INIS)

    Balderacchi, Matteo; Trevisan, Marco; Vischetti, Costantino

    2006-01-01

    The choice of a pesticide fate model at field scale is linked to the available input data. The article describes the available pesticide fate models at a field scale and the guidelines for the choice of the suitable model as function of the data input requested [it

  11. Pesticide Health and Safety Information

    Science.gov (United States)

    Animal Health Safe Use Practices Pest Control Food Safety Low Risk Pesticides Integrated Pest Management directed by the product label. Pesticides may be ingested if stored improperly in food or beverage ; Environment Human Health Animal Health Safe Use Practices Food Safety Environment Air Water Soil Wildlife

  12. Behavior of pesticides in plants.

    Science.gov (United States)

    Logan A. Norris

    1974-01-01

    A number of chemicals of diverse characteristics have arbitrarily been classed together on the basis of their use and given the descriptive name "pesticides." An unfortunate aura of mystery has developed about these chemicals. However, there is nothing unique or mysterious about the chemicals we refer to as "pesticides." Like other chemicals, they...

  13. Multiple stressors and amphibian declines: dual impacts of pesticides and fish on yellow-legged frogs.

    Science.gov (United States)

    Davidson, Carlos; Knapp, Roland A

    2007-03-01

    More than 40% of Earth's 5700+ amphibian species have undergone recent declines. Despite the likely involvement of multiple factors in driving these declines, most studies continue to focus on single stressors. In California (USA), separate studies have implicated either introduced fish or pesticides as causal agents. To date, however, no study has simultaneously evaluated the respective roles of these two potential stressors nor attempted to assess their relative importance, information critical for the development of effective conservation efforts and environmental policies. We examined the role and relative effect of fish and pesticides on the mountain yellow-legged frog (Rana muscosa) using unusually detailed data sets for a large portion of R. muscosa's historic range in California's Sierra Nevada. Habitat characteristics and presence/absence of R. muscosa and fish were quantified at each of 6831 sites during field surveys. Pesticide use upwind of each site was calculated from pesticide application records and predominant wind directions. Using generalized additive models, we found that, after accounting for habitat effects, the probability of R. muscosa presence was significantly reduced by both fish and pesticides, with the landscape-scale effect of pesticides much stronger than that of fish. The degree to which a site was sheltered from the predominant wind (and associated pesticides) was also a significant predictor of R. muscosa presence. Taken together, these results represent the strongest evidence to date that windborne pesticides are contributing to amphibian declines in pristine locations. Our results suggest that amphibian declines may have complex multi-factorial causes, and caution that single-factor studies that demonstrate the importance of one factor should not be used as evidence against the importance of other factors.

  14. Quality control of pesticide products

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-15

    In light of an established need for more efficient analytical procedures, this publication, which documents the findings of an IAEA coordinated research project (CRP) on “Quality Control of Pesticide Products”, simplifies the existing protocol for pesticide analysis while simultaneously upholding existing standards of quality. This publication includes both a report on the development work done in the CRP and a training manual for use by pesticide analysis laboratories. Based on peer reviewed and internationally recognized methods published by the Association of Analytical Communities (AOAC) and the Collaborative International Pesticides Analytical Council (CIPAC), this report provides laboratories with versatile tools to enhance the analysis of pesticide chemicals and to extend the scope of available analytical repertoires. Adoption of the proposed analytical methodologies promises to reduce laboratories’ use of solvents and the time spent on reconfiguration and set-up of analytical equipment.

  15. Quality control of pesticide products

    International Nuclear Information System (INIS)

    2009-07-01

    In light of an established need for more efficient analytical procedures, this publication, which documents the findings of an IAEA coordinated research project (CRP) on “Quality Control of Pesticide Products”, simplifies the existing protocol for pesticide analysis while simultaneously upholding existing standards of quality. This publication includes both a report on the development work done in the CRP and a training manual for use by pesticide analysis laboratories. Based on peer reviewed and internationally recognized methods published by the Association of Analytical Communities (AOAC) and the Collaborative International Pesticides Analytical Council (CIPAC), this report provides laboratories with versatile tools to enhance the analysis of pesticide chemicals and to extend the scope of available analytical repertoires. Adoption of the proposed analytical methodologies promises to reduce laboratories’ use of solvents and the time spent on reconfiguration and set-up of analytical equipment

  16. Pesticide reducing instruments

    DEFF Research Database (Denmark)

    Jacobsen, Lars-Bo; Jensen, Jørgen Dejgård; Andersen, Martin

    2005-01-01

    -mentioned models and tools. All three scenarios are constructed such that they result in the same welfare implication (measured by national consumption in the CGE model). The scenarios are: 1) pesticide taxes resulting in a 25 percent overall reduction; 2) use of unsprayed field margins, resulting in the same...... for improving bio-diversity and securing drinking water. That is, combining economic modeling with physical biological modeling and geological evaluation allows us to select unsprayed field margins as the most effective instrument. Sensitivity analysis conducted on bio-diversity suggest that this result...

  17. 75 FR 62323 - Pesticide Management and Disposal; Standards for Pesticide Containers and Containment; Change to...

    Science.gov (United States)

    2010-10-08

    ... Pesticide Management and Disposal; Standards for Pesticide Containers and Containment; Change to Labeling... the pesticide container and containment regulations to provide an 8-month extension of the labeling... titled ``Pesticide Management and Disposal; Standards for Pesticide Containers and Containment'' (71 FR...

  18. Training Manual Occupational Pesticide Exposure & Health and Safe & Responsible Handling of Pesticides

    NARCIS (Netherlands)

    Maden, van der E.C.L.J.; Koomen, I.

    2016-01-01

    Pesticides are commonly used in the horticulture sector. While emphasis is often on the correct and efficient application of pesticides, the risk associated with application of pesticides receives less attention. Those working with pesticides need to know about occupational pesticide exposure and

  19. BERKELEY/STANFORD: B factory plans

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    For the past several years, accelerator physicists at Lawrence Berkeley Laboratory (LBL) and the Stanford Linear Accelerator Center (SLAC) have been involved in the design of an Asymmetric B Factory to be sited in the tunnel of the PEP electron-positron collider at SLAC

  20. KEKB B-Factory, the luminosity frontier

    International Nuclear Information System (INIS)

    Oide, Katsunobu

    2009-01-01

    The experiment at the KEKB B-Factory, as well as PEP-II, brought the final blow on the 2008 Nobel Prize in Physics for the Kobayashi-Maskawa theory. A few key issues will be described on the design and performance of KEKB to make the world's highest luminosity possible. (author)

  1. The Low-Energy Neutrino Factory

    International Nuclear Information System (INIS)

    Brass, Alan; Geer, Steve; Ellis, Malcolm; Mena, Olga; Pascoli, Silvia

    2008-01-01

    To date most studies of Neutrino Factories have focused on facilities where the energy of the muon in the storage ring has been in the range of 25-50 GeV. In this paper we present a concept for a Low-Energy (∼ 4 GeV) neutrino factory. For baselines of O(1000 km), the rich oscillation pattern at low neutrino interaction energy (0.5 - ∼3 GeV) provides the unique performance of this facility with regard to its sensitivity to CP violation and the determination of the neutrino mass hierarchy. A unique neutrino detector is needed, however, in order to exploit this oscillation pattern. We will describe the basic accelerator facility, demonstrate the methodology of the analysis and give an estimate on how well the Low-Energy neutrino factory can measure θ 13 , CP violation and the mass hierarchy. We will also describe the detector concept that is used, show a preliminary analysis regarding its performance and indicate what R and D is still needed. Finally we will show how the Low-Energy neutrino factory could be a step towards an energy frontier muon collider.

  2. The Energy Factory; EnergieFabriek

    Energy Technology Data Exchange (ETDEWEB)

    Van den Boomen, M.; Van den Dungen, G.J.; Elias, T.; Jansen, M. [Universiteit van Amsterdam UvA, Amsterdam (Netherlands)

    2009-05-15

    The Energy Factory is a collaboration of 26 Dutch local water boards in which options for energy saving and energy production are examined. According to the authors, the initiative of the Energy Factory will lead to a reframing of the role of the water boards. Moreover, they explain how the PPP concept (People, Planet, Profit) may act as platform for negotiations between actors who are involved in the Energy Factory. In addition, the PPP concept is used to demonstrate that the Energy Factory will lead to larger social involvement, social entrepreneurship and growing profits [Dutch] De Energiefabriek is een samenwerkingsverband van 26 waterschappen in Nederland waarin wordt gezocht naar mogelijkheden om energie te besparen en zelf energie te produceren. Volgens de auteurs van deze notitie leidt het initiatief van de Energiefabriek tot een reframing van de rol van waterschappen. Daarnaast leggen ze uit hoe het PPP-concept (People, Profit, Planet) kan fungeren als platform voor onderhandelingen tussen de actoren die betrokken zijn bij de Energiefabriek. Verder wordt met het PPP-concept aangetoond dat de Energiefabriek leidt tot ruimere maatschappelijke betrokkenheid, maatschappelijk ondernemen en winstvergroting.

  3. Racetrack lattices for the TRIUMF KAON factory

    International Nuclear Information System (INIS)

    Servranckx, R.V.; Wienands, U.; Craddock, M.K.; Rees, G.H.

    1989-03-01

    Separated-function racetrack lattices have been developed for the KAON Factory accelerators that have more flexibility than the old circular lattices. Straight sections with zero dispersion are provided for rf cavities and fast injection and extraction, and with controlled dispersion for H - injection and slow extraction. In addition the new lattices have fewer depolarizing resonances than the old circular lattices

  4. Factory automation for heavy electric equipment

    International Nuclear Information System (INIS)

    Rokutani, Takashi; Ninomiya, Iwao; Hatayama, Naokatsu; Kato, Hiroshi; Yano, Hideaki.

    1986-01-01

    The heightening of productivity in the factories manufacturing heavy electric equipment has been advanced so far by the rationalization of direct workings such as NC, robots and the adoption of FMS (flexible manufacturing system). However, as CAD advances, the effective utilization of these data and the expansion to future CIM (computer integrated manufacture) have become to be demanded. In the Hitachi Works of Hitachi Ltd., it was decided to advance the synthetic rationalization by adopting FA (factory automation) system. Steam turbine blades, pipings for nuclear power plants and motor coils were taken up as the objects since these are important parts, and for the purpose of the drastic heightening of QA level, the heightening of accuracy and the shortening of processes, the synchronization with field installation schedule and the creation of safe working place environment, the FA projects for these three sections were simultaneously planned. When the automation of non-mass production factories is promoted, there are the unmanned factories combining FMS lines for relatively many products and those characterized by FMC of shortening preparation time for small lot products, and this is the examples of the former. The system constitution for FA and the production management combined with it are described. The high reliability of the optical network was regarded as important. (Kako, I.)

  5. Employment and Training Problems in New Factories.

    Science.gov (United States)

    International Labour Office, Geneva (Switzerland).

    Does management in newly established factories using highly advanced technology meet special problems in recruitment and training of their workers? Are the traditional training systems supplying the skilled manpower required for running highly sophisticated plants? These were the basic questions asked when the present study was started in seven…

  6. The Mathematics of Symmetrical Factorial Designs

    Indian Academy of Sciences (India)

    The Mathematics of Symmetrical Factorial Designs. Mausumi Bose (nee Sen) obtained her MSc degree in. Statistics from the Calcutta. University and PhD degree from the Indian Statistical. Institute. She is on the faculty of the Indian. Statistical Institute. Her main field of research interest is design and analysis of experiments.

  7. A tau -- charm -- factory at Argonne

    International Nuclear Information System (INIS)

    Berger, E.; Fields, T.; Grosnick, D.; Norem, J.; Repond, J.; Schoessow, P.

    1994-01-01

    Depending on the beam energy setting, the τ -- charm -- factory will be optimized to study physics with τ leptons, with charmed mesons, or with charmonium states. This report gives a short overview of the physics of these topics. Also discussed are the detectors and the costs associated with this project

  8. Plant factories; crop transpiration and energy balance

    NARCIS (Netherlands)

    Graamans, Luuk; Dobbelsteen, van den Andy; Meinen, Esther; Stanghellini, Cecilia

    2017-01-01

    Population growth and rapid urbanisation may result in a shortage of food supplies for cities in the foreseeable future. Research on closed plant production systems, such as plant factories, has attempted to offer perspectives for robust (urban) agricultural systems. Insight into the explicit role

  9. Factorial and reduced K-means reconsidered

    NARCIS (Netherlands)

    Timmerman, Marieke E.; Ceulemans, Eva; Kiers, Henk A. L.; Vichi, Maurizio

    2010-01-01

    Factorial K-means analysis (FKM) and Reduced K-means analysis (RKM) are clustering methods that aim at simultaneously achieving a clustering of the objects and a dimension reduction of the variables. Because a comprehensive comparison between FKM and RKM is lacking in the literature so far, a

  10. Undergraduate Students' Initial Conceptions of Factorials

    Science.gov (United States)

    Lockwood, Elise; Erickson, Sarah

    2017-01-01

    Counting problems offer rich opportunities for students to engage in mathematical thinking, but they can be difficult for students to solve. In this paper, we present a study that examines student thinking about one concept within counting, factorials, which are a key aspect of many combinatorial ideas. In an effort to better understand students'…

  11. The Idea Factory: An Interactive Intergroup Exercise

    Science.gov (United States)

    Rosh, Lisa; Leach, Evan

    2011-01-01

    This article outlines the Idea Factory exercise, an interactive exercise designed to help participants examine group, individual, and organizational factors that affect intergroup conflict. Specific emphasis is placed on exploring the relationship between intra- and intergroup dynamics and identifying managerial practices that foster effective…

  12. Business plan Feed Factory Zambezi Valley, Mozambique

    NARCIS (Netherlands)

    Vernooij, A.G.; Wilschut, S.

    2015-01-01

    This business plan focuses on the establishment of a poultry feed factory, one of the essential elements of a sustainable and profitable poultry meat value chain. There is a growing demand for poultry meat in the Tete Province, and currently a large part of the consumed broilers come from other

  13. MODEL PENGELOLAAN TEACHING FACTORY SEKOLAH MENENGAH KEJURUAN

    Directory of Open Access Journals (Sweden)

    M Burhan R Wijaya

    2013-02-01

    Full Text Available This study aims to identify and develop management models Factory Teaching Vocational School through a series of tests and validation of the model with the approach of reasearch and Development. Teaching Factory Management Models at Vocational Schools is a concept that combines learning management approach learning Competency Based Training (CBT and Production Based Training (PBT in the real atmosphere so that the process of achieving competence or skill skills life skills (life skills in accordance with the standards of graduate work in the industrial world. In particular, this study aims to formulate design management model development Teaching Factory Vocational School. To achieve the research objectives above using the approach of Research and Development, through preliminary studies, design development models, testing and validation. Preliminary study phase is planned to take the flow / stage as follows: the study of literature, study / collection of field data, and a description and analysis of field findings (factual, namely: (1 the description of the characteristics of vocational school with a standard performance indicators that can be poured as the content of the development of Teaching Factory, (2 description of the characteristics and potential development group management model Tefa as an outcome groups to develop and implement management models Tefa for Vocational Schools (3 description of the characteristics of potential stakeholders to support the development and implementation TEFA management model, and (4 preparation of the management model TEFA for Vocational Schools excellence and innovative. Trial design done on a limited scale model group. Then the model was accompanied by outcome group to develop and implement a model TEFA for Vocational Schools to determine whether the model developed can be applied correctly. Data analysis in this study, the preliminary study stage, the findings or the facts about productive learning

  14. Promising pesticide results

    International Nuclear Information System (INIS)

    Wallace, Paula

    2012-01-01

    Full text: Virotec Global Solutions has announced what it believes is the first successful destruction of intractable organochlorine pesticide contamination in industrial wastewater. Dichlorodiphenyltrichloroethane, otherwise known as DDT, is one of the most intractable and persistent chemical compounds known to man. In February remediation specialist Virotec reported it had been successful in reducing DDT contaminant levels. In addition to destroying DDT in wastewater, Virotec showed its ViroFlow Technology can reduce levels of two DDT metabolites (or breakdown products), DDD and DDE, along with an organo-phosphate insecticide called chlorpyrifos. Virotec was commissioned by a large pesticide and fertiliser company to find a way of using its ViroFlow suite of products to reliably reduce high levels of pesticides and heavy metals from wastewater and stormwater at an industrial site. “Along with our strategic partner Green Shadows Commercial from Tasmania, we were able to successfully reduce DDT from 108 parts per billion to under two parts per billion in industrial wastewater using a combination of ozofractionation and ElectroBind reagent,” said business development manager Gisela Barros. “In addition, we were successful in demonstrating similar reductions in Dichlorodiphenyldichloroethane (DDD) from 15.2 parts per billion to under 0.5 parts per billion, and Dichlorodiphenyldichloroethylene (DDE) from one part per billion to under accurate to around 0.5 parts per billion.” The level of detection for pesticides was 0.5 parts per billion (ppb). In addition, ViroFlow reduced chlorpyrifos from 7,972 ppb to 6.4 ppb, arsenic (a key ingredient in pesticide composition) from 0.13 parts per million (ppm) to 0.002 ppm, and zinc from 0.35 ppm to less than 0.005 ppm. “The significance of these findings cannot be overstated,” Barros said. “DDT and its metabolites are among the most persistent and toxic contaminants to be found in soil and groundwater and

  15. Residues leaching from 'Factory of barren ores'

    International Nuclear Information System (INIS)

    Rakhmatov, N.; Khakimov, N.; Nazarov, Kh.M.; Barotov, A.M.

    2012-01-01

    The objective of the present work is safe management of residues from Factory of Barren Ores, their reprocessing, expenditures reduction for remediation of Istiklol city former uranium tailings. For this purpose, some experiences were adopted - Factory of Barren Ores tailing use for filling up the open pit where water with uranium content 3-5 mg/l is located. Factory of Barren Ores waste are passed through heap leaching and have some amount of uranium salts dissolved in water. Thus, we propose to dissolve uranium from Factory of Barren Ores wastes with uranium bearing water flowing out from gallery and filling up the open-pit by radioactive wastes. In so doing, uranium content flowing out from gallery will increase twice, and further, passing them through apricot's shell, as a sorbent, we will clean the water against radionuclides. Residue samples with uranium content 0,015% from Factory of Barren Ores and uranium bearing waters from gallery 1 with uranium content 0,0025 g/l were used for laboratory tests. After which, a slurry was prepared by means of residue mixing with water in ratio of solid and liquid phases (S:L) - 1:2 and 9,7 ml of sulfuric acid (Ρ=1,82) was added which corresponds consumption by H 2 SO 4 176,54 kg/t. For the first test, leaching was carried out during 4 hours at ph=1,6 at room temperature. For the second test, leaching was carried out at 60 d eg C a nd ph=1,6 during 4 hours. Slurry heating and mixing was carried out by means of magnetic mixer. The basic residue leaching indicators are provided in this article.

  16. Long-term lessons on pesticide leaching obtained via the Danish Pesticide Leaching Assessment Programme

    DEFF Research Database (Denmark)

    Rosenbom, Anette E.; Olsen, Preben; Plauborg, Finn

    To avoid any unacceptable influence on the environment posed by pesticides and their degradation products, all pesticides used in the European Union needs authorization. The authorization procedure includes assessing the leaching risk of both pesticides and their degradation products...

  17. Better ways of using pesticides

    International Nuclear Information System (INIS)

    Hussain, M.

    1992-01-01

    The primary role of agriculture is to produce a reliable supply of wholesome food to feed the world's population, safely and without adverse effects on the environment. Pesticides have a crucial part to play in reducing the loss of food during production and after harvesting, and this article discusses how the use of pesticides can be made more efficient. Two particular examples of safer and more effective pesticide delivery systems are described, relating to tsetse fly control in Africa and to the control of weeds in a rice paddy or rice-fish mixed ecosystem. 45 refs, 6 figs

  18. Pesticide use and application: An Indian scenario

    International Nuclear Information System (INIS)

    Abhilash, P.C.; Singh, Nandita

    2009-01-01

    Agricultural development continues to remain the most important objective of Indian planning and policy. In the process of development of agriculture, pesticides have become an important tool as a plant protection agent for boosting food production. Further, pesticides play a significant role by keeping many dreadful diseases. However, exposure to pesticides both occupationally and environmentally causes a range of human health problems. It has been observed that the pesticides exposures are increasingly linked to immune suppression, hormone disruption, diminished intelligence, reproductive abnormalities and cancer. Currently, India is the largest producer of pesticides in Asia and ranks twelfth in the world for the use of pesticides. A vast majority of the population in India is engaged in agriculture and is therefore exposed to the pesticides used in agriculture. Although Indian average consumption of pesticide is far lower than many other developed economies, the problem of pesticide residue is very high in India. Pesticide residue in several crops has also affected the export of agricultural commodities in the last few years. In this context, pesticide safety, regulation of pesticide use, proper application technologies, and integrated pest management are some of the key strategies for minimizing human exposure to pesticides. There is a dearth of studies related to these issues in India. Therefore, the thrust of this paper was to review the technology of application of pesticides in India and recommend future strategies for the rational use of pesticides and minimizing the problems related to health and environment.

  19. Acute pesticide poisoning and pesticide registration in Central America

    International Nuclear Information System (INIS)

    Wesseling, Catharina; Corriols, Marianela; Bravo, Viria

    2005-01-01

    The International Code of Conduct on the Distribution and Use of Pesticides of the Food and Agriculture Organization (FAO) of the United Nations has been for 20 years the most acknowledged international initiative for reducing negative impact from pesticide use in developing countries. We analyzed pesticide use and poisoning in Central America, particularly in Costa Rica and Nicaragua, and evaluated whether registration decisions are based on such data, in accordance with the FAO Code. Extensive use of very hazardous pesticides continues in Central America and so do poisonings with organophosphates, carbamates, endosulfan and paraquat as the main causative agents. Central American governments do not carry out or commission scientific risk assessments. Instead, guidelines from international agencies are followed for risk management through the registration process. Documentation of pesticide poisonings during several decades never induced any decision to ban or restrict a pesticide. However, based on the official surveillance systems, in 2000, the ministers of health of the seven Central American countries agreed to ban or restrict twelve of these pesticides. Now, almost 4 years later, restrictions have been implemented in El Salvador and in Nicaragua public debate is ongoing. Chemical and agricultural industries do not withdraw problematic pesticides voluntarily. In conclusion, the registration processes in Central America do not comply satisfactorily with the FAO Code. However, international regulatory guidelines are important in developing countries, and international agencies should strongly extend its scope and influence, limiting industry involvement. Profound changes in international and national agricultural policies, steering towards sustainable agriculture based on non-chemical pest management, are the only way to reduce poisonings

  20. Flow-based approach for holistic factory engineering and design

    OpenAIRE

    Constantinescu, C.; Westkämper, E.

    2010-01-01

    The engineering of future factories requires digital tools along life cycle phases from investment planning to ramp-up. Manufacturers need scientific-based integrated highly dynamic data management systems for the participative and integrated factory planning. The paper presents a new approach for the continuously integrated product design, factory and process planning, through a service-oriented architecture for the implementation of digital factory tools. A first prototype of the digital fa...

  1. An Interactive Simulation Tool for Production Planning in Bacon Factories

    DEFF Research Database (Denmark)

    Nielsen, Jens Frederik Dalsgaard; Nielsen, Kirsten Mølgaard

    1994-01-01

    The paper describes an interactive simulation tool for production planning in bacon factories. The main aim of the tool is to make it possible to combine the production plans of all parts of the factory......The paper describes an interactive simulation tool for production planning in bacon factories. The main aim of the tool is to make it possible to combine the production plans of all parts of the factory...

  2. Radiation induced pesticidal microbes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Yup; Lee, Y. K.; Kim, J. S.; Kim, J. K.; Lee, S. J.; Lim, D. S

    2001-01-01

    To isolate pesticidal microbes against plant pathogenic fungi, 4 strains of bacteria(K1. K3, K4, YS1) were isolated from mushroom compost and hot spring. K4, K1, K3, YS1 strain showed wide antifungal spectrum and high antifungal activities against 12 kinds of fungi. Specific proteins and the specific transcribed genes were found from the YS1 and its radiation-induced mutants. And knock-out mutants of antifungal activity were derived by transposon mutagenesis. From these knock-out mutants, the antifungal activity related genes and its modification by gamma-ray radiation are going to be studied. These results suggested that radiation could be an useful tool for the induction of functional mutants.

  3. Radiation induced pesticidal microbes

    International Nuclear Information System (INIS)

    Kim, Ki Yup; Lee, Y. K.; Kim, J. S.; Kim, J. K.; Lee, S. J.; Lim, D. S.

    2001-01-01

    To isolate pesticidal microbes against plant pathogenic fungi, 4 strains of bacteria(K1. K3, K4, YS1) were isolated from mushroom compost and hot spring. K4, K1, K3, YS1 strain showed wide antifungal spectrum and high antifungal activities against 12 kinds of fungi. Specific proteins and the specific transcribed genes were found from the YS1 and its radiation-induced mutants. And knock-out mutants of antifungal activity were derived by transposon mutagenesis. From these knock-out mutants, the antifungal activity related genes and its modification by gamma-ray radiation are going to be studied. These results suggested that radiation could be an useful tool for the induction of functional mutants

  4. Control of pesticides 2003

    DEFF Research Database (Denmark)

    Krongaard, T.; Petersen, K. K.; Christoffersen, C.

    . 3) Insecticides containing cypermethrin, deltamethrin, lambda-cyhalothrin, methoprene and cyromazine. 4) Plant growth regulators containing 1-napthylacetic acid. All products were examined for the content of the respective active ingredients and for the content of OPEO and NPEO. All samples but one...... containing methoprene complied with the accepted tolerance limits with respect to the content of the active ingredient as specified in Danish Statutory Order on pesticides. None of the 44 examined samples contained OPEO, but 5 of the samples contained NPEO. Three of these five samples were produced before...... the agreement. On three products, the content of active ingredient was declared only in g/L, but not in % (w/w). One product was declared as the ester and not as the acid...

  5. The Virtual Factory Teaching System (VFTS): Project Review and Results.

    Science.gov (United States)

    Kazlauskas, E. J.; Boyd, E. F., III; Dessouky, M. M.

    This paper presents a review of the Virtual Factory Teaching (VFTS) project, a Web-based, multimedia collaborative learning network. The system allows students, working alone or in teams, to build factories, forecast demand for products, plan production, establish release rules for new work into the factory, and set scheduling rules for…

  6. e sup + e sup - Factories: PEP-II, KEKB, DAPHINE

    CERN Document Server

    Guiducci, S

    2001-01-01

    In 1999 two B-factories, PEP-II and KEK, and a PHI-factory, DAPHINE, started their physics experiments. A status report of the three factories is presented. A description of the interaction regions, strongly influenced by the detector requirements, and of the machine background in the detectors is presented.

  7. The Physics of the B Factories

    Energy Technology Data Exchange (ETDEWEB)

    Bevan, A.J. [Queen Mary Univ., London (United Kingdom); Golob, B. [Ljubljana Univ. (Slovenia). Faculty of Mathematics and Physics; J. Stefan Institute, Ljubljana (Slovenia); Mannel, T. [Siegen Univ. (Germany). Theoretische Physik 1; Collaboration: BABAR Collaboration; Belle Collaboration; and others

    2014-11-15

    The inspiration for this book came from Fran@cois le Diberder. During his term as spokesperson for BABAR he laid down a vision for the two B Factory detector collaborations, BABAR and Belle, to work together on a book that would describe the methodologies used and physics results obtained by those experiments. A key ideal emphasized from the outset was that this book should be written from a pedagogical perspective; it should be of interest to the student and expert alike. This vision was presented during a BABAR collaboration meeting on the island of Elba in May 2008 and a follow up Belle collaboration meeting at KEK, with visiting colleagues from the BABAR collaboration, and was embraced by the community. A number of workshops involving people from the theoretical community as well as the two collaborations were held on four continents over the following years. The resulting book, ''The Physics of the B Factories'', is a testament to the way that this concept captured the zeitgeist on both sides of the Pacific Ocean. This book is divided into three parts, the first of which provides a brief description of the B Factories, including a short (though not exhaustive) historical perspective, as well as descriptions of the detectors, ancillary data acquisition systems and data (re)processing systems that were built by the two detector collaborations in the late 1990's. The second part of the book discusses tools and methods that are frequently used when analyzing the data collected. These range from details of low level reconstruction algorithms and abstract summaries of statistical methods to high level prescriptions used when evaluating systematic uncertainties on measurements of observables. The third part of the book is devoted to physics results. This includes sufficient theoretical discussion in order for the reader to understand the context of the work being described. We are indebted to our colleagues from the theoretical community who

  8. The Physics of the B Factories

    International Nuclear Information System (INIS)

    Bevan, A.J.; Golob, B.; Mannel, T.

    2014-01-01

    The inspiration for this book came from Fran@cois le Diberder. During his term as spokesperson for BABAR he laid down a vision for the two B Factory detector collaborations, BABAR and Belle, to work together on a book that would describe the methodologies used and physics results obtained by those experiments. A key ideal emphasized from the outset was that this book should be written from a pedagogical perspective; it should be of interest to the student and expert alike. This vision was presented during a BABAR collaboration meeting on the island of Elba in May 2008 and a follow up Belle collaboration meeting at KEK, with visiting colleagues from the BABAR collaboration, and was embraced by the community. A number of workshops involving people from the theoretical community as well as the two collaborations were held on four continents over the following years. The resulting book, ''The Physics of the B Factories'', is a testament to the way that this concept captured the zeitgeist on both sides of the Pacific Ocean. This book is divided into three parts, the first of which provides a brief description of the B Factories, including a short (though not exhaustive) historical perspective, as well as descriptions of the detectors, ancillary data acquisition systems and data (re)processing systems that were built by the two detector collaborations in the late 1990's. The second part of the book discusses tools and methods that are frequently used when analyzing the data collected. These range from details of low level reconstruction algorithms and abstract summaries of statistical methods to high level prescriptions used when evaluating systematic uncertainties on measurements of observables. The third part of the book is devoted to physics results. This includes sufficient theoretical discussion in order for the reader to understand the context of the work being described. We are indebted to our colleagues from the theoretical community who have helped us achieve

  9. Portable Material Culture and Death Factory Auschwitz

    Directory of Open Access Journals (Sweden)

    Adrian T. Myers

    2007-11-01

    Full Text Available Like any other factory, the death factory of Auschwitz consumed primary materials and produced secondary products. Unique to Auschwitz, though, is that the primary material consumed was human life; not just the life of the breathing human body, but also the material possessions associated with that life. The detritus of this most efficient genocide – clothing, jewellery, food, corpses – was appropriated and put to new uses by the SS and the prisoners. Others have recognised the various postwar material cultural outcomes of the camp: the writing, the film, the theatre, the art, the tourism. This article, however, demonstrates that the material culture of Auschwitz is not a phenomenon exclusive to the postwar era. It focuses on the fact that inside the camp during the war, despite the landscape of death and deprivation, intimate interaction between humans and material culture continued.

  10. JINR tau-charm factory design study

    International Nuclear Information System (INIS)

    Perel'shtejn, E.; Aleksandrov, V.; Antropov, V.

    1993-01-01

    The review on tau-charm factory in JINR (Dubna) is presented. The structure scheme of tau-charm factory is described. The problems on injection complex are discussed: the composition, the working regime and parameters. The magnetic lattice of a booster is described. A versatile magnet lattice is used in tau-charm collider. It can realize both conventional flat beam scheme and monochromatization scheme. The results of chromaticity correction in high emittance lattice are presented. The list of parameters of tau-charm collider is given. The technical proposal of magnetic elements of booster and collider and their power supplies is made, as well as RF power supply in collider and vacuum system in its periodic cell. 12 refs.; 12 figs.; 3 tabs

  11. B factory rf system design issues

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1992-06-01

    We discuss the issues of relevance to the design of a B factory RF system. First, the general parameter regime is outlined, and the reasons behind certain commonly made choices are indicated. This regime involves high beam currents, and many relatively short bunches. Next, the physics difficulties associated with coupled-bunch instabilities are described briefly. We then describe in general terms the alternative approaches taken by various B factory designers, the motivation for these choices, and the technical issues raised by them. Technical solutions have been proposed for both the room-temperature and the superconducting RF scenarios, and considerable R ampersand D is being carried out worldwide to confirm and optimize these solutions

  12. Physics at e+e- factories

    International Nuclear Information System (INIS)

    Lueth, V.; MacFarlane, D.B.

    1991-02-01

    Feasible designs are well advanced for high-luminosity e + e - storage rings which produce B 0 bar B 0 pairs either at rest or, in what appears to be a more promising option, boosted in the detector frame. Facilities which could provide samples of 30--100 fb -1 per year on the Υ(4S) will be proposed in early 1991. Here we examine the principal physics goal of such B Factories, namely CP violation in the b system. Methods in a variety of channels, estimated event samples, and detector requirements are all considered. We conclude that the physics argument for an e + e - B Factory is well documented, and compelling. 50 refs., 22 figs., 10 tabs

  13. B factory RF system design issues

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1992-01-01

    We discuss the issues of relevance to the design of a B factory RF system. First, the general parameter regime is outlined, and the reasons behind certain commonly made choices are indicated. This regime involves high beam currents, and many relatively short bunches. Next, the physics difficulties associated with coupled-bunch instabilities are described briefly. We then describe in general terms the alternative approaches taken by various B factory designers, the motivation for these choices, and the technical issues raised by them. Technical solutions have been proposed for both the room-temperature and the superconducting RF scenarios, and considerable R ampersand D is being carried out worldwide to confirm and optimize these solutions

  14. Individual Pesticides in Registration Review

    Science.gov (United States)

    You can used the Chemical Search database to search pesticides by chemical name and find their registration review dockets, along with Work Plans, risk assessments, interim and final decisions, tolerance rules, and cancellation actions.

  15. Pesticide Product Information System (PPIS)

    Science.gov (United States)

    PPIS includes registrant name and address, chemical ingredients, toxicity category, product names, distributor brand names, site/pest uses, pesticidal type, formulation code, and registration status for all products registered in the U.S.

  16. Neutrino Factory Targets and the MICE Beam

    International Nuclear Information System (INIS)

    Walaron, Kenneth A.

    2007-01-01

    The future of particle physics in the next 20 years must include detailed study of neutrinos. The first proof of physics beyond the Standard Model of particle physics is evident in results from recent neutrino experiements which imply that neutrinos have mass and flavour mixing. The Neutrino Factory is the leading contender to measure precisely the neutrino mixing parameters to probe beyond the Standard Model physics.

  17. Review of proposed kaon factory facilities

    International Nuclear Information System (INIS)

    Macek, R.J.

    1985-01-01

    A number of proton accelerator facilities, popularly called ''Kaon Factories,'' have been proposed to extend the intensity frontier from about 1 GeV to higher energies in the range of 15 to 45 GeV. Seven proposed facilities - LAMPF II, TRIUMF II, SIN II, AGS II, KEK, MUNICH, and KYOTO - are reviewed with emphasis on capabilities of the experimental facilities. Costs and the choice of energy and current are also discussed. 7 refs., 29 figs., 7 tabs

  18. Design studies for the Positron Factory

    International Nuclear Information System (INIS)

    Okada, S.; Sunaga, H.; Kaneko, H.; Masuno, S.; Kawasuso, A.; Sakai, T.; Takizawa, H.; Yotsumoto, K.; Honda, Y.; Tagawa, S.

    1996-01-01

    In the design study for the Positron Factory, a feasibility of simultaneous extraction of multi-channel monoenergetic positron beams, which had been proposed at the previous conference (Linac 94), was demonstrated by an experiment using an electron linac. On the basis of the experimental result, an efficient moderator structure, which is composed of honeycomb-like assembled moderator foils and reflectors, is proposed. (author)

  19. Muon front end for the neutrino factory

    Directory of Open Access Journals (Sweden)

    C. T. Rogers

    2013-04-01

    Full Text Available In the neutrino factory, muons are produced by firing high-energy protons onto a target to produce pions. The pions decay to muons and pass through a capture channel known as the muon front end, before acceleration to 12.6 GeV. The muon front end comprises a variable frequency rf system for longitudinal capture and an ionization cooling channel. In this paper we detail recent improvements in the design of the muon front end.

  20. Muon front end for the neutrino factory

    CERN Document Server

    Rogers, C T; Prior, G; Gilardoni, S; Neuffer, D; Snopok, P; Alekou, A; Pasternak, J

    2013-01-01

    In the neutrino factory, muons are produced by firing high-energy protons onto a target to produce pions. The pions decay to muons and pass through a capture channel known as the muon front end, before acceleration to 12.6 GeV. The muon front end comprises a variable frequency rf system for longitudinal capture and an ionization cooling channel. In this paper we detail recent improvements in the design of the muon front end.

  1. LAMPF: the meson factory. A LASL monograph

    Energy Technology Data Exchange (ETDEWEB)

    Allred, J.C.

    1977-08-01

    A general and simplified introduction to the entire concept of LAMPF is given in terms of its experimental capabilities. Parts of the current experimental program are used as illustrative examples. Topics discussed include: (1) the evolution of the meson factory; (2) accelerator construction; (3) strong focusing; (4) accelerator innovations at LAMPF; (5) photons and pions; (6) muons as nuclear probes; (7) nuclear chemistry; (8) radiobiology and medical applications; (9) radioisotope production; (10) materials testing; and (11) LAMPF management and users group. (PMA)

  2. Collective issues related to B-factories

    International Nuclear Information System (INIS)

    Pestrikov, D.V.

    1993-02-01

    This report reviews the limitations on the performance of the planned B- and Φ-factories due to the collective interactions of stored bunches. Together with the traditional revision of the limitations due to the single- and multi-bunch interaction with surrounding electrodes, we briefly discuss in this report the limitations on the performance due to collective beam-beam instabilities of colliding beams and instabilities due to the collective interaction of beams with the ions. (author)

  3. LAMPF: the meson factory. A LASL monograph

    International Nuclear Information System (INIS)

    Allred, J.C.

    1977-08-01

    A general and simplified introduction to the entire concept of LAMPF is given in terms of its experimental capabilities. Parts of the current experimental program are used as illustrative examples. Topics discussed include: (1) the evolution of the meson factory; (2) accelerator construction; (3) strong focusing; (4) accelerator innovations at LAMPF; (5) photons and pions; (6) muons as nuclear probes; (7) nuclear chemistry; (8) radiobiology and medical applications; (9) radioisotope production; (10) materials testing; and (11) LAMPF management and users group

  4. The Factory of the Future, Group Exhibition

    OpenAIRE

    Dean, Lionel T.

    2016-01-01

    3D Printing, The factory of the future, Lieu du Design (centre for Design), Paris This exhibition dedicated entirely to 3D printing technology was billed as “the first in France wholly devoted to exploring the interdisciplinary and multifaceted topic of 3D printing technology and its undeniable influence on everything from industry, to economics, to creative and social issues, demonstrated to the public through achievements in the fields of 3D design, 3D printed architecture, 3D printed fa...

  5. Cell factories for a sustainable world

    DEFF Research Database (Denmark)

    Kindtler, Jens William

    2016-01-01

    The Novo Nordisk Foundation Center for Biosustainability (CFB) is a university research center under the Technical University of Denmark within the field of design, engineering and construction of superior cell factories for the production of biopharmaceuticals, anti-infective compounds, industrial......-spectrum inhibitors against multi-drug resistant (MDR) Gram-negative bacterial pathogens using co-Adaptive Laboratory Evolution, 3. Design and engineering of E. coli and Saccharomyces cerevisiae for biobased production of various classes of chemicals. CFB has 230 employees....

  6. A biophysical model for transcription factories

    International Nuclear Information System (INIS)

    Canals-Hamann, Ana Z; Neves, Ricardo Pires das; Reittie, Joyce E; Iñiguez, Carlos; Soneji, Shamit; Enver, Tariq; Buckle, Veronica J; Iborra, Francisco J

    2013-01-01

    Transcription factories are nuclear domains where gene transcription takes place although the molecular basis for their formation and maintenance are unknown. In this study, we explored how the properties of chromatin as a polymer may contribute to the structure of transcription factories. We found that transcriptional active chromatin contains modifications like histone H4 acetylated at Lysine 16 (H4K16ac). Single fibre analysis showed that this modification spans the entire body of the gene. Furthermore, H4K16ac genes cluster in regions up to 500 Kb alternating active and inactive chromatin. The introduction of H4K16ac in chromatin induces stiffness in the chromatin fibre. The result of this change in flexibility is that chromatin could behave like a multi-block copolymer with repetitions of stiff-flexible (active-inactive chromatin) components. Copolymers with such structure self-organize through spontaneous phase separation into microdomains. Consistent with such model H4K16ac chromatin form foci that associates with nascent transcripts. We propose that transcription factories are the result of the spontaneous concentration of H4K16ac chromatin that are in proximity, mainly in cis

  7. A tau-charm-factory at Argonne

    International Nuclear Information System (INIS)

    Norem, J.; Repond, J.

    1994-01-01

    In this paper we explore the possibility of building a tau-charm-factory at the Argonne National Laboratory. A tau-charm-factory is an e + e - collider with a center-of-mass energy between 3.0 GeV and 5.0 GeV and a luminosity of at least 1 x 10 33 cm -2 s -1 . Once operational, the facility will produce large samples of τ pairs, charm mesons, and charmonium with either negligible or well understood backgrounds. This will lead to high precision measurements in the second generation quark and the third generation lepton sectors that cannot be done at other facilities. Basic physical properties and processes, such as the tau neutrino mass, rare tau decays, charm decay constants, rare charm meson decays, neutral D 0 -- meson mixing, and many more will be studied with unique precision. An initial design of the collider including the injector system is described. The design shows that a luminosity of at least 1 x 10 33 cm -2 s -1 can be achieved over the entire center-of-mass energy range of the factory

  8. Ultrastructural Characterization of Zika Virus Replication Factories

    Directory of Open Access Journals (Sweden)

    Mirko Cortese

    2017-02-01

    Full Text Available Summary: A global concern has emerged with the pandemic spread of Zika virus (ZIKV infections that can cause severe neurological symptoms in adults and newborns. ZIKV is a positive-strand RNA virus replicating in virus-induced membranous replication factories (RFs. Here we used various imaging techniques to investigate the ultrastructural details of ZIKV RFs and their relationship with host cell organelles. Analyses of human hepatic cells and neural progenitor cells infected with ZIKV revealed endoplasmic reticulum (ER membrane invaginations containing pore-like openings toward the cytosol, reminiscent to RFs in Dengue virus-infected cells. Both the MR766 African strain and the H/PF/2013 Asian strain, the latter linked to neurological diseases, induce RFs of similar architecture. Importantly, ZIKV infection causes a drastic reorganization of microtubules and intermediate filaments forming cage-like structures surrounding the viral RF. Consistently, ZIKV replication is suppressed by cytoskeleton-targeting drugs. Thus, ZIKV RFs are tightly linked to rearrangements of the host cell cytoskeleton. : Cortese et al. show that ZIKV infection in both human hepatoma and neuronal progenitor cells induces drastic structural modification of the cellular architecture. Microtubules and intermediate filaments surround the viral replication factory composed of vesicles corresponding to ER membrane invagination toward the ER lumen. Importantly, alteration of microtubule flexibility impairs ZIKV replication. Keywords: Zika virus, flavivirus, human neural progenitor cells, replication factories, replication organelles, microtubules, intermediate filaments, electron microscopy, electron tomography, live-cell imaging

  9. Engineering Robustness of Microbial Cell Factories.

    Science.gov (United States)

    Gong, Zhiwei; Nielsen, Jens; Zhou, Yongjin J

    2017-10-01

    Metabolic engineering and synthetic biology offer great prospects in developing microbial cell factories capable of converting renewable feedstocks into fuels, chemicals, food ingredients, and pharmaceuticals. However, prohibitively low production rate and mass concentration remain the major hurdles in industrial processes even though the biosynthetic pathways are comprehensively optimized. These limitations are caused by a variety of factors unamenable for host cell survival, such as harsh industrial conditions, fermentation inhibitors from biomass hydrolysates, and toxic compounds including metabolic intermediates and valuable target products. Therefore, engineered microbes with robust phenotypes is essential for achieving higher yield and productivity. In this review, the recent advances in engineering robustness and tolerance of cell factories is described to cope with these issues and briefly introduce novel strategies with great potential to enhance the robustness of cell factories, including metabolic pathway balancing, transporter engineering, and adaptive laboratory evolution. This review also highlights the integration of advanced systems and synthetic biology principles toward engineering the harmony of overall cell function, more than the specific pathways or enzymes. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Neutrinos: from the Workshop to the Factory

    CERN Multimedia

    2001-01-01

    Over the next 5 years much work will be done to reach a theoretical and practical description of a neutrino factory. How could this project turn out to be an interesting future option for CERN? Neutrino beams travelling from CERN to the Canary Islands? And to the Svalbard archipelago in Norway? Or even to the Pyhaesalmi Mine in Finland? Why neutrinos? And why so far? The answers provide one of CERN's next challenging options: the construction of a high-energy muon storage ring to provide neutrino beams. This project, nicknamed 'neutrino factory', now figures in CERN's middle term plan as a recognized and supported research and development project. International collaborations, with other European laboratories and also with America and Japan, are now being set up. Long baseline locations for neutrino oscillations studies at a CERN based neutrino factory. Early in its history, LEP established that there exist just three kinds of light neutrinos, those associated with the electron, muon, and tau leptons. For a...

  11. An asymmetric B factory based on PEP

    Energy Technology Data Exchange (ETDEWEB)

    1991-02-01

    In this report we describe a design for a high-luminosity Asymmetric B Factory to be built in the PEP tunnel on the SLAC site. This proposal, a collaborative effort SLAC, LBL, and LLNL, is the culmination of more than two years of effort aimed at the design and construction of an asymmetric e{sup +}e{sup {minus}} collider capable of achieving a luminosity of L = 3 {times} 10{sup 33} cm{sup {minus}2} s{sup {minus}1}. The configuration adopted utilizes two storage rings, and electron ring operating at 9 GeV and a positron ring at 3.1 GeV, each with a circumference of 2200 m. The high-energy ring is an upgrade of the PEP storage ring at SLAC; all PEP magnets and most power supplies will be reused. The upgrade consists primarily of replacing the PEP vacuum chamber and RF system with newly designed versions optimized for the high-current environment of the B Factory. The low-energy ring will be newly constructed and will be situated atop the high-energy ring in the PEP tunnel. Utilities already installed in the PEP tunnel are largely sufficient to operate the two B Factory storage rings.

  12. An asymmetric B factory based on PEP

    International Nuclear Information System (INIS)

    1991-02-01

    In this report we describe a design for a high-luminosity Asymmetric B Factory to be built in the PEP tunnel on the SLAC site. This proposal, a collaborative effort SLAC, LBL, and LLNL, is the culmination of more than two years of effort aimed at the design and construction of an asymmetric e + e - collider capable of achieving a luminosity of L = 3 x 10 33 cm -2 s -1 . The configuration adopted utilizes two storage rings, and electron ring operating at 9 GeV and a positron ring at 3.1 GeV, each with a circumference of 2200 m. The high-energy ring is an upgrade of the PEP storage ring at SLAC; all PEP magnets and most power supplies will be reused. The upgrade consists primarily of replacing the PEP vacuum chamber and RF system with newly designed versions optimized for the high-current environment of the B Factory. The low-energy ring will be newly constructed and will be situated atop the high-energy ring in the PEP tunnel. Utilities already installed in the PEP tunnel are largely sufficient to operate the two B Factory storage rings

  13. Factorial complexity and Morally Debatable Behaviors

    Directory of Open Access Journals (Sweden)

    Grimaldo Muchotrigo, Mirian P.

    2011-12-01

    Full Text Available Currently, from the scientific and professional practice point of view, comes out the necessity to know more about moral permissiveness, as it seems to be an increase in “moral relativism”.. Because it, it this is important to have tools to collect valid and reliable information about moral in social situations defined as social and personal behavior issue. This paper presents a technical note of The Morally Debatable Behaviors Scale (MDBS from Harding & Phillips (1986, which was developed in USA and mainly focused on young people and adults. This technical note makes direct reference to a recent Latin American study (Merino & Grimaldo, 2010; this article focuses on the internal structure and the problems associated with evidences of factorial complexity among items of the MDBS. This means that the interpretation of scores is not factorially simple and could not be achieved by a conceptual distinction between the latent constructs applied to the study sample.. The results in the previous study of the factorial complexity leads the researcher to decide whether an instrument for measuring this aspect may contain a reasonable amount of complexity that is consistent with what is in reality, or look for the unidimensional and simple structure.

  14. 77 FR 74003 - Pesticides; Draft Guidance for Pesticide Registrants on Antimicrobial Pesticide Products With...

    Science.gov (United States)

    2012-12-12

    ... Insecticide, Fungicide, and Rodenticide Act (FIFRA) or are required to register pesticides. The following list... remediation, on nonporous and porous surfaces, for residual activity, for mold prevention, and in heating...

  15. Household pesticide usage in the United States.

    Science.gov (United States)

    Savage, E P; Keefe, T J; Wheeler, H W; Mounce, L; Helwic, L; Applehans, F; Goes, E; Goes, T; Mihlan, G; Rench, J; Taylor, D K

    1981-01-01

    A total of 10,000 U.S. households in 25 standard metropolitan statistical areas and 25 counties were included in the United States. More than 8,200 households granted an interview. Nine of every ten households in the United States used some types of pesticide in their house, garden, or yard. Households in the southeastern United States used the most pesticides. Although more than 500 different pesticide formulations were used by the sampled households, 15 pesticides accounted for 65.5% of all pesticides reported in this study. Thirteen of these 15 pesticides were insecticides, one was a herbicide, and one was a rodenticide.

  16. Confirmatory factorial analysis of TEOSQp / Análise factorial confirmatória do TEOSQp

    Directory of Open Access Journals (Sweden)

    Helder M. Fernandes

    2010-01-01

    Full Text Available The present research assessed the reliability, factorial validity and measurement invariance (by gender of the Portuguese version of TEOSQ –Task and Ego Orientation in Sport Questionnaire (Fonseca & Biddle, 2001. Data were collected from 1010 physical education students with a mean age of 15.42 ( SD=1.91. Factorial and invariance measurements were tested via confirmatory factorial analysis. Results supported internal consistency for the two proposed subscales (task and ego. Based on modification indices and theoretical justification the TEOSQ p was reduced to 12 items with better goodness-of-fit indices for the oblique model. The results of gender invariance did not provide full empirical support to the multi-group equivalence assumption, being suggested that TEOSQ p does not measure in the same way goal orientations for boys (orthogonal model and girls (oblique model. In light of these results, conceptual, empirical and practical issues were discussed.

  17. In-Factory Learning - Qualification For The Factory Of The Future

    Science.gov (United States)

    Quint, Fabian; Mura, Katharina; Gorecky, Dominic

    2015-07-01

    The Industry 4.0 vision anticipates that internet technologies will find their way into future factories replacing traditional components by dynamic and intelligent cyber-physical systems (CPS) that combine the physical objects with their digital representation. Reducing the gap between the real and digital world makes the factory environment more flexible, more adaptive, but also more complex for the human workers. Future workers require interdisciplinary competencies from engineering, information technology, and computer science in order to understand and manage the diverse interrelations between physical objects and their digital counterpart. This paper proposes a mixed-reality based learning environment, which combines physical objects and visualisation of digital content via Augmented Reality. It uses reality-based interaction in order to make the dynamic interrelations between real and digital factory visible and tangible. We argue that our learning system does not work as a stand-alone solution, but should fit into existing academic and advanced training curricula.

  18. Investigation on the level and movement of Mercury contaminants around storage areas and food processing factories in Hassahesa town, Sudan

    International Nuclear Information System (INIS)

    Abdelrahman, Nawal Ahmed Mohamed

    1999-11-01

    A total of 62 surface soil samples were taken from various sites in Hassahesa town and analyzed for total mercury level using X-ray fluorescence spectrometer. Sites were chosen to represent the soil of pesticide store, food processing factories (involved in using contaminated seeds as fuel), near stock of redundant cotton seeds and neighbouring cotton fields. Control soils were sampled from similar soil type south Hassahesa town. The results indicated an elevated mercury level in all samples analyzed far exceeding the background and normal range for mercury in soil. The highest level of contamination was found in soil of the pesticide store (51ppm), followed by the tow food factories (24 ppm and 19 ppm). Horizontal movement of mercury contaminants at various rates from foci of area selected was noticed, wind direction and/ or topography apparently had some role in this movement. The level of total mercury in the control soil was exceeding the background and normal range for mercury in soils reported from other places. Various aspects of levels of mercury contamination, their movements, transportation and toxicological impacts on various forms of life were discussed.(Author)

  19. Investigation on the level and movement of mercury contaminants around storage areas and food processing factories in Hassahesa town

    International Nuclear Information System (INIS)

    Abdelrahman, Nawal Ahmed Mohamed

    1999-11-01

    A total of 62 surface soil samples were taken from various sites in Hassahesa town and analyzed for total mercury level using x-ray fluorescence spectrometer. Sites were chosen to represent the soil of pesticide store, food processing factories (involved in using contaminated seeds as fuel), nera stock of redundant cotton seeds and neighbouring cotton fields. Control soils were sampled from similar soil type south Hassahesa town. The results indicated an elevated mercury level in all samples analyzed far exceeding the background and normal range for mercury in soil. The highest level of contamination was found in soil of pesticide store (51 ppm), followed by the two food factories (24 ppm and 19 ppm). Horizontal movement of mercury contaminants at various rates from foci of areas selected was noticed, wind direction and/or topography apparently had some role in this movement. The level of total mercury in the control soil was exceeding the background and normal range for mercury in soils reported from other places. Various aspects of levels of mercury contamination, their movements, transportation and toxicological impacts on various forms of life were discussed. (Author)

  20. The Tau-Charm Factory in the ERA of B-Factories and CESR

    International Nuclear Information System (INIS)

    Beers, L.V.; Perl, M.L.

    1994-10-01

    This paper is a collection of presentations made at a conference on tau-charm factories, held at the Stanford Linear Accelerator Center and Stanford University on August 15-16, 1994. The papers presented summarize the physics which can be learned from such a facility, the advantages it would present over planned B-factories and large centers such as CESR, and the types of decay modes which could be observed. More detailed studies of tau physics are opened up, as well as charmonium and charmed systems. Seperate presentations to the proceedings are indexed individually into the database

  1. 75 FR 33705 - Pesticide Management and Disposal; Standards for Pesticide Containers and Containment; Change to...

    Science.gov (United States)

    2010-06-15

    ... Pesticide Management and Disposal; Standards for Pesticide Containers and Containment; Change to Labeling... the pesticide container and containment regulations to provide a 4-month extension of the 40 CFR 156... pesticide labels to comply with the label requirements in the container and containment regulations. DATES...

  2. Diamond Growth in the Subduction Factory

    Science.gov (United States)

    Bureau, H.; Frost, D. J.; Bolfan-Casanova, N.; Leroy, C.; Estève, I.

    2014-12-01

    Natural diamonds are fabulous probes of the deep Earth Interior. They are the evidence of the deep storage of volatile elements, carbon at first, but also hydrogen and chlorine trapped as hydrous fluids in inclusions. The study of diamond growth processes in the lithosphere and mantle helps for our understanding of volatile elements cycling between deep reservoirs. We know now that inclusion-bearing diamonds similar to diamonds found in nature (i.e. polycrystalline, fibrous and coated diamonds) can grow in hydrous fluids or melts (Bureau et al., GCA 77, 202-214, 2012). Therefore, we propose that the best environment to promote such diamonds is the subduction factory, where highly hydrous fluids or melts are present. When oceanic plates are subducted in the lithosphere, they carry an oceanic crust soaked with seawater. While the slabs are traveling en route to the mantle, dehydration processes generate saline fluids highly concentrated in NaCl. In the present study we have experimentally shown that diamonds can grow from the saline fluids (up to 30 g/l NaCl in water) generated in subducted slabs. We have performed multi-anvil press experiments at 6-7 GPa and from 1300 to 1400°C during 6:00 hours to 30:00 hours. We observed large areas of new diamond grown in epitaxy on pure diamond seeds in salty hydrous carbonated melts, forming coated gems. The new rims are containing multi-component primary inclusions. Detailed characterizations of the diamonds and their inclusions have been performed and will be presented. These experimental results suggest that multi-component salty fluids of supercritical nature migrate with the slabs, down to the deep mantle. Such fluids may insure the first stage of the deep Earth's volatiles cycling (C, H, halogen elements) en route to the transition zone and the lower mantle. We suggest that the subduction factory may also be a diamond factory.

  3. Pesticide risks around the home (image)

    Science.gov (United States)

    Pesticides are substances which kill or deter unwanted pests, such as insects or rodents. These substances can ... avoid an accidental ingestion is to keep all pesticides out of the reach of children.

  4. Neurobehavioral and neurodevelopmental effects of pesticide exposures

    DEFF Research Database (Denmark)

    London, Leslie; Beseler, Cheryl; Bouchard, Maryse F

    2012-01-01

    The association between pesticide exposure and neurobehavioral and neurodevelopmental effects is an area of increasing concern. This symposium brought together participants to explore the neurotoxic effects of pesticides across the lifespan. Endpoints examined included neurobehavioral, affective ...

  5. Secondary Containers and Service Containers for Pesticides

    Science.gov (United States)

    Secondary containers and service containers are used by pesticide applicators in the process of applying a pesticide. EPA does not require secondary containers or service containers to be labeled or to meet particular construction standards. Learn more.

  6. Chiral Pesticides: Identification, Description and Environmental Implications

    Science.gov (United States)

    Anthropogenic chemicals, including pesticides, are a major source of contamination and pollution in the environment. Pesticides have many positive uses: increased food production, decreased damage to crops and structures, reduced disease vector populations, and more. Nevertheless...

  7. How We Engage Our Pesticide Stakeholders

    Science.gov (United States)

    The success of EPA's pesticide program is directly connected to our efforts to engage all stakeholders. In addition to meetings on pesticide-specific actions, we sponsor advisory committees that include diverse, independent stakeholders.

  8. 75 FR 4383 - Pesticide Products: Registration Applications

    Science.gov (United States)

    2010-01-27

    ..., Biopesticides and Pollution Prevention Division (7511P), Office of Pesticide Programs, Environmental Protection..., Biopesticides and Pollution Prevention Division, Office of Pesticide Programs. [FR Doc. 2010-1582 Filed 1-26-10...

  9. Organochlorine Pesticides in the Environment

    Science.gov (United States)

    Stickel, L.F.

    1968-01-01

    Each year for nearly 20 years, thousands of pounds of persistent organochlorine pesticides have been applied to outdoor areas in many countries. These compounds may last for a very long time in the environment, and be carried by wind, water, and animals to places far distant from where they are used. As a result, most living organisms now contain organochlorine residues. This paper constitutes a selective review of the literature concerning the occurrence, distribution, and effects of organochlorines in the environment. Highest concentrations generally occur in carnivorous species. Thus predatory and fish-eating birds ordinarily have higher residues than do herbivores; quantities are similar in birds of similar habits in different countries. Any segment of the ecosystem - marshland, pond, forest, or field - receives various amounts and kinds of pesticides at irregular intervals. The different animals absorb, detoxify, store, and excrete pesticides at different rates. Different degrees of magnification of pesticide residues by living organisms in an environment are the practical result of many interactions that are far more complex than implied by the statement of magnification up the food chain. These magnifications may be millions of times from water to mud or only a few times from food to first consumer. Direct mortality of wild animals as an aftermath of recommended pesticide treatments has been recorded in the literature of numerous countries. However, accidents and carelessness also accompany pesticide use on a percentage basis and are a part of the problem. More subtle effects on the size and species composition of populations are more difficult to perceive in time to effect remedies. The possibility of ecological effects being mediated through changes in physiology and behavior has received some attention and has resulted in some disquieting findings. These include discovery of the activity of organochlorines in stimulating the breakdown of hormones or in

  10. Recent developments at the TRIUMF meson factory

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1976-10-01

    The TRIUMF meson factory, which is based on a 6-sector isochronous cyclotron accelerating H - ions to 520 MeV, has been operating since December 1974. Two proton beams are extracted simultaneously to feed the two experimental areas. Characteristics of the beams and beam lines are given. Work is also proceeding on (i) additional beam lines, (ii) a 180 kW beam dump and thermal neutron source, (iii) a medium resolution proton spectrometer, and (iv) adding third harmonic flat-topping to the RF to permit separation of the internal orbits and reduction of the energy spread of the extracted beam to 0.1 MeV. (author)

  11. RI beam factory project at RIKEN

    CERN Document Server

    Motobayashi, T

    2003-01-01

    Construction of the RI beam factory project in the first phase has started. The aim of the project is to provide intense radio-isotopes (RI) beams at energies of several hundred MeV/nucleon in a wide range of atomic masses. These beams will be produced by the projectile fragmentation of primary beams accelerated by a cascade of the existing ring cyclotron and a series of new ring cyclotrons. Improvements of the existing facility made for the new cyclotron complex have extended the energy range of available beams, which already opened new domains of study.

  12. The physics case of the Neutrino Factory

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Cadenas, J J [IFIC, CSIC-UV, Valencia (Spain)], E-mail: gomez@ific.uv.es

    2008-11-01

    I discuss the physics case of the standard Neutrino Factory facility coupled to an iron detector to exploit the so-called 'Golden-Channel'. The performance of the facility is impressive, although it is not free from degeneracies arising from a combination of physics and instrumental limitations. Nevertheless, one could explore at great depth the parameter of the leptonic mixing matrix as well as the mass hierarchy. Best performance is obtained with two baselines (one of them very long) and an improved magnetic detector with low energy detection threshold.

  13. Advanced manufacturing: optimising the factories of tomorrow

    International Nuclear Information System (INIS)

    Philippon, Patrick

    2013-01-01

    Faced with competition Patrick Philippon - Les Defis du CEA no.179 - April 2013 from the emerging countries, the competitiveness of the industrialised nations depends on the ability of their industries to innovate. This strategy necessarily entails the reorganisation and optimisation of the production systems. This is the whole challenge for 'advanced manufacturing', which relies on the new information and communication technologies. Interactive robotics, virtual reality and non-destructive testing are all technological building blocks developed by CEA, now approved within a cross-cutting programme, to meet the needs of industry and together build the factories of tomorrow. (author)

  14. Tau/Charm Factory Accelerator Report

    OpenAIRE

    M. E. BiaginiINFN, Laboratori Nazionali Frascati, Italy; R. BoniINFN, Laboratori Nazionali Frascati, Italy; M. BoscoloINFN, Laboratori Nazionali Frascati, Italy; A. ChiarucciINFN, Laboratori Nazionali Frascati, Italy; R. CiminoINFN, Laboratori Nazionali Frascati, Italy; A. ClozzaINFN, Laboratori Nazionali Frascati, Italy; A. DragoINFN, Laboratori Nazionali Frascati, Italy; S. GuiducciINFN, Laboratori Nazionali Frascati, Italy; C. LigiINFN, Laboratori Nazionali Frascati, Italy; G. MazzitelliINFN, Laboratori Nazionali Frascati, Italy; R. RicciINFN, Laboratori Nazionali Frascati, Italy; C. SanelliINFN, Laboratori Nazionali Frascati, Italy; M. SerioINFN, Laboratori Nazionali Frascati, Italy; A. StellaINFN, Laboratori Nazionali Frascati, Italy; S. TomassiniINFN, Laboratori Nazionali Frascati, Italy

    2014-01-01

    The present Report concerns the current status of the Italian Tau/Charm accelerator project and in particular discusses the issues related to the lattice design, to the accelerators systems and to the associated conventional facilities. The project aims at realizing a variable energy Flavor Factory between 1 and 4.6 GeV in the center of mass, and succeeds to the SuperB project from which it inherits most of the solutions proposed in this document. The work comes from a cooperation involving t...

  15. Racetrack lattices for the TRIUMF KAON factory

    International Nuclear Information System (INIS)

    Servranckx, R.V.; Craddock, M.K.

    1989-05-01

    Separated-function racetrack lattices have been developed for the KAON Factory accelerators that have more flexibility than the old circular lattices. The arcs of the large rings have a regular FODO structure with a superimposed six-fold symmetric modulation of the betafunction in order to raise γ t to infinity. In the small rings, γ t is kept high enough by choosing a sufficiently large phase advance in the arcs. Straight sections with zero dispersion are provided for rf cavities and fast injection and extraction, and with controlled dispersion for H - injection and slow extraction. The ion-optical properties of the lattices and the results from tracking studies are discussed

  16. Tests of CPT invariance at neutrino factories

    International Nuclear Information System (INIS)

    Bilenky, Samoil M.; Freund, Martin; Lindner, Manfred; Ohlsson, Tommy; Winter, Walter

    2002-01-01

    We investigate possible tests of CPT invariance on the level of event rates at neutrino factories. We do not assume any specific model but phenomenological differences in the neutrino-antineutrino masses and mixing angles in a Lorentz invariance preserving context, such as could be induced by physics beyond the standard model. We especially focus on the muon neutrino and antineutrino disappearance channels in order to obtain constraints on the neutrino-antineutrino mass and mixing angle differences; we found, for example, that the sensitivity |m 3 -m(bar sign) 3 |(less-or-similar sign)1.9x10 -4 eV could be achieved

  17. 77 FR 38285 - Pesticide Products; Registration Applications

    Science.gov (United States)

    2012-06-27

    ... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OPP-2012-0101; FRL-9348-5] Pesticide Products... announces receipt of applications to register pesticide products containing new active ingredients not... Pollution Prevention Division (7511P) or the Registration Division (7505P), Office of Pesticide Programs...

  18. Fact Sheets on Pesticides in Schools.

    Science.gov (United States)

    National Coalition against the Misuse of Pesticides, Washington, DC.

    This document consists of a collection of fact sheets about the use of pesticides in schools and how to reduce it. The sheets are: (1) "Alternatives to Using Pesticides in Schools: What Is Integrated Pest Management?"; (2) "Health Effects of 48 Commonly Used Pesticides in Schools"; (3) "The Schooling of State Pesticide…

  19. Earthworm tolerance to residual agricultural pesticide contamination

    DEFF Research Database (Denmark)

    Givaudan, Nicolas; Binet, Françoise; Le Bot, Barbara

    2014-01-01

    of soluble glutathione-S-transferases (sGST) and catalase increased with soil pesticide contamination in A. caliginosa. Pesticide stress was reflected in depletion of energy reserves in A. chlorotica. Acute exposure of pre-adapted and naïve A. caliginosa to pesticides (fungicide Opus ®, 0.1 μg active...

  20. Rare B decays at B factories

    International Nuclear Information System (INIS)

    Trabelsi, Karim

    2010-01-01

    Radiative and Electroweak Penguin Decays are Flavor Changing Neutral Currents (FCNC) occurring in the Standard Model only at the loop level. They are characterized by high sensitivity to New Physics (they can appear in the loop with size comparable to leading SM contributions) and they are Complementary to the direct production of new particles expected at LHC. Huge datasets collected at the two B- factories, BaBar and Belle, have made it possible to explore precisely these decays in exclusive channels and inclusive measurements. b →sγ, b→dγ, b→s l + l - , B + →τν, B→Dτν etc measured provide tests of SM predictions and interesting BSM constraints: Charged Higgs bounds from b →sγ, B + →τν, B + →Dτν; Constraints on Wilson coefficients C 7 , C 9 and C 10 ; and Constraints on |V td |/|V ts |. They provide interesting signatures: B(B + →τ + ν) direct measurement versus CKM fit; and large forward-backward asymmetry of K* l + l - . Final Belle/BaBar data samples are yet to be analyzed and even more interesting results are expected at Super B factories with two orders of magnitude larger data samples

  1. Radiation safety design of super KEKB factory

    International Nuclear Information System (INIS)

    Sanami, Toshiya

    2015-01-01

    The SuperKEKB factory, which was scheduled to start operation early 2015, is an electron-positron collider designed to produce an 80x10"3"4-1/cm"2/s luminosity, which is 40 times greater than the KEKB factory. Built to investigate CP violation and 'new physics' beyond the Standard Model, the facility consists of a 7-GeV electron/3.5-GeV positron linac, a 1.1- GeV positron damping ring, beam transport, and a 7-GeV electron/4-GeV positron collider. To meet this level of luminosity, the collider will be operated with a small beam size and a large crossing angle at the interaction point. According to particle tracking simulations, beam losses under these conditions will be 35 times more than those previously operated. To help optimise shielding configurations, leakage radiation and induced activity are estimated through empirical equations and detailed Monte-Carlo simulations using MARS15 code for the interaction region, beam halo collimators, emergency pathways, ducts, forward direction tunnels, and positron production target. Examples of shielding strategies are presented to reduce both leakage dose and airborne activity for several locations in the facility. (authors)

  2. Muon Acceleration: Neutrino Factory and Beyond

    Energy Technology Data Exchange (ETDEWEB)

    Bogacz, Alex [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2018-03-01

    We summarize the current state of a concept for muon acceleration aimed at a future Neutrino Factory and extendable to Higgs Factory. The main thrust of these studies was to reduce the overall cost while maintaining performance by exploring the interplay between the complexity of the cooling systems and the acceptance of the accelerator complex. To ensure adequate survival for the short-lived muons, acceleration must occur at high average gradient. The need for large transverse and longitudinal acceptances drives the design of the acceleration system to an initially low RF frequency, e.g., 325 MHz, which is then increased to 650 MHz as the transverse size shrinks with increasing energy. High-gradient normal conducting RF cavities at these frequencies require extremely high peak-power RF sources. Hence superconducting RF (SRF) cavities are chosen. We consider an SRF-efficient design based on a multi-pass (4.5) ?dogbone? RLA, extendable to multi-pass FFAG-like arcs.

  3. Particle identification at an asymmetric B Factory

    International Nuclear Information System (INIS)

    Coyle, P.; Eigen, G.; Hitlin, D.; Oddone, P.; Ratcliff, B.; Roe, N.; Va'vra, J.; Ypsilantis, T.

    1991-09-01

    Particle identification systems are an important component of any detector at a high-luminosity, asymmetric B Factory. In particular, excellent hadron identification is required to probe CP violation in B 0 decays to CP eigenstates. The particle identification systems discussed below also provide help in separating leptons from hadrons at low momenta. We begin this chapter with a discussion of the physics motivation for providing particle identification, the inherent limitations due to interactions and decays in flight, and the requirements for hermiticity and angular coverage. A special feature of an asymmetric B Factory is the resulting asymmetry in the momentum distribution as a function of polar angle; this will also be quantified and discussed. In the next section the three primary candidates, time-of-flight (TOF), energy loss (dE/dx), and Cerenkov counters, both ring-imaging and threshold, will be briefly described and evaluated. Following this, one of the candidates, a long-drift Cerenkov ring-imaging device, is described in detail to provide a reference design. Design considerations for a fast RICH are then described. A detailed discussion of aerogel threshold counter designs and associated R ampersand D conclude the chapter. 56 refs., 64 figs., 13 tabs

  4. The rehabilitation of ancient gas factory sites

    International Nuclear Information System (INIS)

    Costes, J.M.; Hua, C.

    1996-01-01

    In France, the inheritance of ancient town gas factories, mainly under the responsibility of Gaz de France, has left pollutants in the soils of their sites. The aim of the national company is to control these pollutants. Several hundred of town gas factories were exploited in France from 1798 (date of the invention of the process by Lebon) to the end of the 60's. The town gas, obtained from high temperature pyrogenic decomposition of coal, led to by-products which were stored or mixed with the soil. This paper describes the environmental and quality policy carried out by Gaz de France to characterize and remove the pollutants (coke, clinker, tar, phenols, ammoniated water, hydrogen sulphide, cyanides, benzene, toluene, xylenes..) to evaluate the risks of exposure of contaminants and their possible impact on human health. A method with 17 criteria was elaborated to characterize the sites and the rehabilitation comprises three steps: the environmental audit (evaluation of the concentration of pollutants and of their possible environmental and human impact), the complementary analysis (extension of the contaminated area, nature and concentration of pollutants, geologic and hydrogeologic characterisation of the site), and the rehabilitation itself when necessary (confinement or elimination of pollutants using thermal, physico-chemical or biological treatments). (J.S.)

  5. Optimization of a furniture factory layout

    Directory of Open Access Journals (Sweden)

    Tadej Kanduč

    2015-03-01

    Full Text Available This paper deals with the problem of optimizing a factory floor layout in a Slovenian furniture factory. First, the current state of the manufacturing system is analyzed by constructing a discrete event simulation (DES model that reflects the manufacturing processes. The company produces over 10,000 different products, and their manufacturing processes include approximately 30,000 subprocesses. Therefore, manually constructing a model to include every subprocess is not feasible. To overcome this problem, a method for automated model construction was developed to construct a DES model based on a selection of manufacturing orders and relevant subprocesses. The obtained simulation model provided insight into the manufacturing processes and enable easy modification of model parameters for optimizing the manufacturing processes. Finally, the optimization problem was solved: the total distance the products had to traverse between machines was minimized by devising an optimal machine layout. With the introduction of certain simplifications, the problem was best described as a quadratic assignment problem. A novel heuristic method based on force-directed graph drawing algorithms was developed. Optimizing the floor layout resulted in a significant reduction of total travel distance for the products.

  6. Pesticides: Food and environmental implications

    International Nuclear Information System (INIS)

    1988-01-01

    Pesticides are an integral part of modern agriculture, also in most developing countries. Although the annual average consumption of active ingredients in agriculture may be below 0.1 kg a.i./ha, most countries now consume more than 2 kg a.i./ha; some of the intensively cropped regions in South-East Asia are exposed to even higher amounts. Inherent contamination of the environment follows if rules and regulations are not strictly adhered to. The search for safer, less persistent and more specific pesticides and examination of the fate of applied pesticides in various regions of the world were the main themes of the symposium. Special emphasis was placed on the use of nuclear techniques, especially on labelled compounds in research. The Proceedings include all the papers and posters that were presented. Refs, figs and tabs

  7. Application of Pesticide Phytoremediation in Irrigated Rice Fields System Using Eceng Gondok (Eichhornia crassipes) Plants

    Science.gov (United States)

    Febriani, Ika Kartika; Hadiyanto

    2018-02-01

    The problem of environmental pollution especially urban water pollution becomes major issue in Indonesia. The cause of water pollution is not only from industrial factory waste disposal but also other causes which become pollution factor. One cause of water pollution is the existence of agricultural activities with the use of the amount of pesticides that exceed the threshold. As regulated in Government Regulation No. 82/2001 on Water Quality Management and Water Pollution Control, it is necessary to manage water quality and control water pollution wisely by taking into account the interests of current and future generations as well as the ecological balance. To overcome the problem of water pollution due to agricultural activities, it is necessary to conduct research on phytoremediation technique by utilizing eceng gondok plant. It is excepted that using this phytoremediation technique can reduce the problem of water pollution due to the use of pesticides on agricultural activities.

  8. Application of Pesticide Phytoremediation in Irrigated Rice Fields System Using Eceng Gondok (Eichhornia crassipes Plants

    Directory of Open Access Journals (Sweden)

    Kartika Febriani Ika

    2018-01-01

    Full Text Available The problem of environmental pollution especially urban water pollution becomes major issue in Indonesia. The cause of water pollution is not only from industrial factory waste disposal but also other causes which become pollution factor. One cause of water pollution is the existence of agricultural activities with the use of the amount of pesticides that exceed the threshold. As regulated in Government Regulation No. 82/2001 on Water Quality Management and Water Pollution Control, it is necessary to manage water quality and control water pollution wisely by taking into account the interests of current and future generations as well as the ecological balance. To overcome the problem of water pollution due to agricultural activities, it is necessary to conduct research on phytoremediation technique by utilizing eceng gondok plant. It is excepted that using this phytoremediation technique can reduce the problem of water pollution due to the use of pesticides on agricultural activities.

  9. INDOOR THERMAL CONDITION OF FACTORY BUILDING IN BANGLADESH

    OpenAIRE

    Muhammed Abdullah Al Sayem Khan; Mohd. Hamdan Ahmad; Tareef Hayat Khan

    2011-01-01

    Bangladesh is a developing country and has a lot of factories for different products for local use and also export to abroad. Garments industries are one of the top most items of exported items. A huge number of populations are working in garments industries. But these factories are not well designed in sense of the thermal environment. Workers experiences sickness related to indoor environment. The productions of these factories are affected due to employees’ health condition. The research i...

  10. Pesticide bioconcentration modelling for fruit trees.

    Science.gov (United States)

    Paraíba, Lourival Costa

    2007-01-01

    The model presented allows simulating the pesticide concentration evolution in fruit trees and estimating the pesticide bioconcentration factor in fruits. Pesticides are non-ionic organic compounds that are degraded in soils cropped with woody species, fruit trees and other perennials. The model allows estimating the pesticide uptake by plants through the water transpiration stream and also the time in which maximum pesticide concentration occur in the fruits. The equation proposed presents the relationships between bioconcentration factor (BCF) and the following variables: plant water transpiration volume (Q), pesticide transpiration stream concentration factor (TSCF), pesticide stem-water partition coefficient (K(Wood,W)), stem dry biomass (M) and pesticide dissipation rate in the soil-plant system (k(EGS)). The modeling started and was developed from a previous model "Fruit Tree Model" (FTM), reported by Trapp and collaborators in 2003, to which was added the hypothesis that the pesticide degradation in the soil follows a first order kinetic equation. The FTM model for pesticides (FTM-p) was applied to a hypothetic mango plant cropping (Mangifera indica) treated with paclobutrazol (growth regulator) added to the soil. The model fitness was evaluated through the sensitivity analysis of the pesticide BCF values in fruits with respect to the model entry data variability.

  11. The Danish Pesticide Leaching Assessment Programme

    DEFF Research Database (Denmark)

    Rosenbom, Annette Elisabeth; Brüsch, Walter Michael; Juhler, Rene K.

    In 1998, the Danish Parliament initiated the Pesticide Leaching Assessment Programme (PLAP), an intensive monitoring programme aimed at evaluating the leaching risk of pesticides under field conditions. The objective of the PLAP is to improve the scientific foundation for decision......-making in the Danish regulation of pesticides. The specific aim is to analyse whether pesticides applied in accordance with current regulations leach to groundwater in unacceptable concentrations. The programme currently evaluates the leaching risk of 41 pesticides and 40 degradation products at five agricultural......, thiamethoxam, tribenuronmethyl, and triasulfuron) did not leach during the 1999-2009 monitoring period. 13 of the applied pesticides exhibited pronounced leaching of the pesticide and/or their degradation product(-s) 1 m b.g.s. in yearly average concentrations exceeding 0.1 μg/l (maximum allowable...

  12. Análise factorial confirmatória do TEOSQp Confirmatory factorial analysis of TEOSQp

    Directory of Open Access Journals (Sweden)

    Helder M. Fernandes

    2010-04-01

    Full Text Available O propósito do presente estudo foi avaliar a confiabilidade, a validade factorial e a invariância (por sexo da versão portuguesa do TEOSQ (Fonseca & Biddle, 2001. Integraram a amostra 1010 estudantes com uma média de idade de 15,42 anos. A análise factorial e da invariância foi avaliada através da análise factorial confirmatória. Os resultados corroboram a proposta de uma estrutura de duas subescalas (tarefa e ego. Com base nos índices de modificação e justificação teórica, o TEOSQ p foi reduzido a 12-itens, com melhores índices de adequação para o modelo oblíquo. Os resultados relativos à invariância por sexo não apresentaram apoio empírico total para a assumpção de equivalência multi-grupo, sugerindo que o TEOSQ p não parece avaliar as orientações cognitivas do mesmo modo, para os indivíduos do sexo masculino (modelo ortogonal e feminino (modelo oblíquo. Face aos resultados obtidos, foram discutidas as implicações conceptuais, empíricas, assim como os aspectos de carácter aplicado.The present research assessed the reliability, factorial validity and measurement invariance (by gender of the Portuguese version of TEOSQ -Task and Ego Orientation in Sport Questionnaire (Fonseca & Biddle, 2001. Data were collected from 1010 physical education students with a mean age of 15.42 ( SD=1.91. Factorial and invariance measurements were tested via confirmatory factorial analysis. Results supported internal consistency for the two proposed subscales (task and ego. Based on modification indices and theoretical justification the TEOSQ p was reduced to 12 items with better goodness-of-fit indices for the oblique model. The results of gender invariance did not provide full empirical support to the multi-group equivalence assumption, being suggested that TEOSQ p does not measure in the same way goal orientations for boys (orthogonal model and girls (oblique model. In light of these results, conceptual, empirical and practical

  13. [Demodicosis of dogs--a factorial disease?].

    Science.gov (United States)

    Gothe, R

    1989-09-01

    Demodex canis is a normal resident of the intact canine skin, being present in small numbers in virtually every dog. Most animals are only carriers of the mites and do not develop clinical symptoms, therefore, demodectic mange has already to be considered as a factorial disease. The modus operandi of transition of clinically inapparent colonization of the mites into a disease may be explained according to investigations so far published multifactorially and thereby essentially as consequences of primary or secondary immunodepression. A primary immunodepression is initially based most probably on a hereditary defect of T-cells and is subsequently reinforced by substances, which are presumably synthesized and liberated not only by mites but also by secondary bacterial agents. A secondary immunodepression operates as trigger mechanism of a clinical manifestation after corticosteroid or cytostatic therapy or in course of underlying diseases of potentially immunodepressive nature, i.e., malignant neoplasia, hepatopathies, hyperadrenocorticism and lymphosarcoma.

  14. ATHEROSCLEROSIS DISEASE: A MULTI-FACTORIAL PATHOLOGY

    Directory of Open Access Journals (Sweden)

    Marcieli da Luz Giroldo1; Arienne Serrano Alves1; Francielle Baptista1

    2007-06-01

    Full Text Available Atherosclerosis or arterial stiffening is a gradual disease that restricts the normal blood flow in different areas of body and maylead to secondary illnesses as myocardial infarction and cerebral stroke. Innumerable factors are related to the development ofatherosclerosis, among them are the dyslipidemia; genetic factors; arterial hypertension; diabetes mellitus; obesity; smoking;lack of exercise; pulmonary infection by Chlamydia and stress. Due to multi-factorial atherosclerosis characteristics,innumerable drugs, with differentiated mechanisms of action, are being elaborated to be used in prevention and control of thisdisease. However, beyond the pharmacological therapy, a balanced diet, physical activity and elimination of risk habits, assmoking, also are need for controlling atherosclerosis progression, as well as for the increase of expectative and quality of life

  15. Nuclear structure physics at RI beam factory

    International Nuclear Information System (INIS)

    Otsuka, Takaharu

    1998-01-01

    The nuclear structure physics is becoming extremely interesting owing to recent development of RI beam factories. Among various interesting developments in this field, I will focus upon two subjects. One is the breaking of the usual magic numbers in unstable nuclei, and the other is the invention of a new method for quantum many-body problems: Quantum Monte Carlo diagonalization method (QMCD). For the first subject, I will discuss the vanishing of N=8 and 20 magic numbers in 11 Li and 32 Mg, respectively. For the latter, I will present brief description of the theory and results of some applications including the one to 64 Ge, a proton-rich unstable nucleus. (author)

  16. The B-factory project at KEK

    International Nuclear Information System (INIS)

    Kurokawa, Shin-ichi; Satoh, Kotaro

    1993-01-01

    The B-Factory project at KEK aims at constructing an accelerator complex which enables us to detect the CP-violation effect of B-mesons. It is a two-ring electron-positron collider of 3.5x8 GeV in the existing TRISTAN tunnel. The design peak luminosity is 10 34 cm -2 s -1 , which will be realized in two steps: from a small-angle collision with a luminosity of 2x10 33 cm -2 s -1 to a large-angle crab-crossing scheme with the final luminosity of 10 34 cm -2 s -1 . Progress of design work and present status of R and D are reported. (author)

  17. N-Nitrosamines in the factory environment

    Energy Technology Data Exchange (ETDEWEB)

    Fajen, J M; Fine, D H; Rounbehler, D P

    1980-01-01

    Under the NIOSH-sponsored contract, a total of 40 surveys were conducted at 28 manufacturing plants. The industries investigated were the fish, dye, leather, rubber and manufacturers and users of cutting fluids. NDELA, NMOR, NDMA and NDPhA were found in the air of several factories. In a chrome tannery, NDMA was identified at levels as high as 47 micrograms/m3 and NMOR was found at 27 micrograms/m3 in a rubber tire plant. This study has resulted in an increased understanding of man's exposure to exogenous N-nitrosamines. It is conceivable, from the information obtained in this study, that nitrosamine exposure comparable to that in the tire and rubber industry exists in other industries not yet surveyed. NIOSH is continuing its research on nitrosamines in the industrial environment. A full, industry-wide report on the 40 plant surveys is being compiled for publication.

  18. Lattices for the TRIUMF KAON factory

    International Nuclear Information System (INIS)

    Servranckx, R.V.; Craddock, M.K.

    1989-09-01

    Separated-function racetrack lattices have been developed for the KAON Factory accelerators that have more flexibility than the old circular lattices. The arcs of the large rings have a regular FODO structure with a superimposed six-fold symmetric modulation of the betafunction in order to raise γ t to infinity. Straight sections with zero dispersion are provided for rf cavities and fast injection and extraction, and with controlled dispersion for H - injection and slow extraction. For the small rings, sixfold symmetric circular lattices with high γ t are retained. In the Accumulator lattice, a straight section with double waist and controlled η function allows for H - injection and phase-space painting. The ion-optical properties of the lattices and the results from tracking studies are discussed

  19. Intense muon beams and neutrino factories

    International Nuclear Information System (INIS)

    Parsa, Z.

    2000-01-01

    High intensity muon sources are needed in exploring neutrino factories, lepton flavor violating muon processes, and lower energy experiments as the stepping phase towards building higher energy μ + μ - colliders. We present a brief overview, sketch of a neutrino source, and an example of a muon storage ring at BNL with detector(s) at Fermilab, Sudan, etc. Physics with low energy neutrino beams based on muon storage rings (μSR) and conventional Horn Facilities are described and compared. CP violation Asymmetries and a new Statistical Figure of Merit to be used for comparison is given. Improvements in the sensitivity of low energy experiments to study Flavor changing neutral currents are also included

  20. Producción escrita: Estructura factorial

    Directory of Open Access Journals (Sweden)

    María Esperanza HERRERA GARCÍA

    2009-11-01

    Full Text Available Este estudio se planteó con la idea de comprobar de forma empírica si los indicadores lingüísticos obtenidos en investigaciones realizadas sobre comprensión lectora aparecían también como significativos en el análisis de la producción escrita. Si bien la investigación psicológica ha demostrado en numerosas ocasiones la relación existente entre comprensión y producción en el sentido de una maduración anterior de la primera con respecto a la segunda, podemos considerar a priori la existencia de indicadores que nos permitan medir ambos aspectos. Para ello buscamos la estructura factorial que presentan los indicadores lingüísticos que vamos a considerar y comprobaremos si presenta los factores encontrados en comprensión lectora.

  1. Targeting population heterogeneity for optimal cell factories

    DEFF Research Database (Denmark)

    Heins, Anna-Lena; Carlqvist, Magnus; Helmark, S.

    the heterogeneity level of the population. To further investigate these phenomena and gain a deeper understanding of population heterogeneity, Saccharomyces cerevisiae growth reporter strains based on the expression of green fluorescent protein (GFP) were constructed which enabled us to perform single cell level...... analysis, and thereby created the possibility to map population heterogeneity. A factorial design with pH, glucose concentration and oxygen level was performed in batch cultivations using the growth reporter strains to evaluate the effect of those environmental factors on heterogeneity level and amount......To achieve an efficient production process, it is essential to optimize both the strain and the cultivation conditions. Traditionally, a microbial population has been considered homogeneous in optimization studies of fermentation processes. However, research has shown that a typical microbial...

  2. High-gravity brewing utilizing factorial design

    Directory of Open Access Journals (Sweden)

    R. B. Almeida

    2000-06-01

    Full Text Available A number of factors can influence the behavior of yeast during fermentation. Some of these factors (initial wort concentration, initial pH and percentage of corn syrup in the composition of the wort were studied in order to determine their influence on the productivity of fermentation. Fermentations were carried out at 25ºC utilizing a 2³ factorial design of these factors. The results showed that the percentage of corn syrup had no influence on process productivity, whereas initial pH and especially initial wort concentration did. It can be concluded that using pH and initial wort concentration values higher than those utilized in this work (5.5 and 20ºP, respectively will result in a higher productivity.

  3. Present status of positron factory project

    International Nuclear Information System (INIS)

    Okada, S.; Sunaga, H.; Kaneko, H.; Tachibana, H.; Yotsumoto, K.; Okamoto, J.

    1992-01-01

    The Japan Atomic Energy Research Institute, JAERI, has been promoting design studies for the 'Positron Factory', in which linac-based intense monoenergetic positron beams are planned to be applied to advanced materials characterization and new fields of basic research. A tentative goal of the beam intensity is 10 10 s -1 , which is assumed to be realized with an electron linac of 100 kW class with a beam energy around 100 to 150 MeV. We performed a technical survey on the dedicated linac. It confirmed technical feasibility of manufacturing the state-of-the-art machine. We have been carrying out a design study of the target. A new concept of the target design is proposed, which is expected to supply intense slow positron beams simultaneously for multiple beam channels, on the basis of Monte Carlo simulations. (author)

  4. Achille Maramotti, between factory and collection

    Directory of Open Access Journals (Sweden)

    Chiara Pirozzi

    2016-11-01

    Full Text Available The article analyzes Achille Maramotti’s figure and links between entrepreneurship and his passion for art and contemporary collections: from the desire to expose his private collection inside Max Mara factory to create a collection that was the mirror of the artistic experiments of his time. The article analyzes the critical contributions in the development of Maramotti Collection and, in particular, the relationship between Achille Maramotti and Mario Diacono that, as the Emilian collector, is expert and admirer of European and American painting of the second half of the twentieth century. Achille Maramotti, sons and daughter are considered among the most influential collectors in the world, and represents a successful example of contemporary art collection linked to the image and business management; the Max Mara fashion house.

  5. KEKB and PEP-II B Factories

    International Nuclear Information System (INIS)

    Seeman, J.T.

    1997-01-01

    Two asymmetric B-Factories KEKB at KEK and PEP-II at SLAC are under construction, designed to study CP violation in the b-quark sector with a center of mass energy of 10.58 GeV. These two new accelerators are high luminosity two-ring two-energy e + e - colliders with one interaction point. There are many challenging accelerator physics and engineering issues associated with the high beam currents and high luminosities of these rings. The chosen solutions to these issues and the general parameters of the two rings are described in detail side-by-side. KEKB and PEP-II are well into the installation phase and are both scheduled to be completed in 1998. The particle physics programs are scheduled to start in 1999

  6. Status of the TRIUMF KAON factory proposal

    International Nuclear Information System (INIS)

    Craddock, M.K.

    1988-03-01

    Over the last year considerable progress has been achieved on both technical and political fronts. Hardware studies have continued on both magnet power supplies and on rf cavities - the latter work gaining an extra dimension from a recently-instituted formal collaboration with LAMPF. A racetrack-shaped lattice is being considered in conjunction with a three-element slow extraction system in an effort to reduce losses to the 0.1% level. British Columbia has agreed to fund the buildings and tunnels (Cdn $87M) and is making the KAON Factory its tope priority project with the Canadian federal government. A joint federal-provincial delegation has traveled abroad and found that a number of countries would consider significant contributions to the cost. Government approval contingent upon such contributions is anticipated later in 1988, together with preconstruction R and D funds

  7. Improved premises for cell factory development

    DEFF Research Database (Denmark)

    Søgaard, Karina Marie

    The sustainable manufacturing of medicines, materials and chemicals is enabled with biotechnology, and the key to the development of new processes, as well as improvement of existing ones, lies in our fundamental understanding of the biological systems we manipulate. Recombinant protein production...... is at the core of biotechnology and numerous molecular tools and bacterial strains have been developed over the past four decades for this purpose. Understanding of the genetic code and our ability to manipulate genetic material, paves the way for the microbial cell factory development that enables production......, and building a platform for enhanced expression of certain plant genes in bacteria. The relevance of the conducted research to the field of biotechnology is covered, as well as necessary scientific background and history. Specifically, the surprisingly minor effects of tRNA overexpression on the production...

  8. Golden measurements at a neutrino factory

    International Nuclear Information System (INIS)

    Cervera, A.; Donini, A.; Gavela, M.B.; Gomez Cadenas, J.J.; Hernandez, P.; Mena, O.; Rigolin, S.

    2000-01-01

    The precision and discovery potential of a neutrino factory based on muon storage rings is studied. For three-family neutrino oscillations, we analyse how to measure or severely constraint the angle θ 13 , CP-violation, MSW effects and the sign of the atmospheric mass difference Δm 2 23 . We present a simple analytical formula for the oscillation probabilities in matter, with all neutrino mass differences non-vanishing, which clarifies the subtleties involved in disentangling the unknown parameters. The appearance of 'wrong-sign muons' at three reference baselines is considered: 732 km, 3500 km, and 7332 km. We exploit the dependence of the signal on the neutrino energy, and include as well realistic background estimations and detection efficiencies. The optimal baseline turns out to be O (3000 km). Analyses combining the information from different baselines are also presented

  9. Golden measurements at a neutrino factory

    CERN Document Server

    Cervera-Villanueva, Anselmo; Gavela-Legazpi, Maria Belen; Cadenas, J J G; Hernández, Pilar; Mena, O; Rigolin, Stefano

    2000-01-01

    The precision and discovery potential of a neutrino factory based on muonstorage rings is studied. For three-family neutrino oscillations, we analysehow to measure or severely constraint the angle $\\theta_{13}$, CP violation,MSW effects and the sign of the atmospheric mass difference $\\Delta m^2_{23}$.We present a simple analytical formula for the oscillation probabilities inmatter, with all neutrino mass differences non-vanishing, which clarifies thesubtleties involved in disentangling the unknown parameters. The appearance of``wrong-sign muons'' at three reference baselines is considered: 732 km, 3500km, and 7332 km. We exploit the dependence of the signal on the neutrinoenergy, and include as well realistic background estimations and detectionefficiencies. The optimal baseline turns out to be ${\\cal O}(3000$ km).Analyses combining the information from different baselines are also presented.

  10. Chiral Synthons in Pesticide Syntheses

    NARCIS (Netherlands)

    Feringa, Bernard

    1988-01-01

    The use of chiral synthons in the preparation of enantiomerically pure pesticides is described in this chapter. Several routes to chiral synthons based on asymmetric synthesis or on natural products are illustrated. Important sources of chiral building blocks are reviewed. Furthermore the

  11. New insights into pesticide photoprotection.

    Science.gov (United States)

    Trivella, Aurélien; Richard, Claire

    2014-04-01

    Photolysis may be a significant route of pesticide dissipation on crops, leading to an increase of pesticide use. Spraying strong absorbing compounds (photoprotector) along with pesticide is an attractive strategy to prevent the photodegradation phenomenon. The aim of this study is to get a better understanding of the parameters governing the photoprotection efficiency. Experiments were conducted using formulated sulcotrione as a pesticide and a grape wine extract as a photoprotector. These compounds were irradiated using simulated solar light as dried deposits on carnauba wax films or on disks of tobacco leaves and analyzed by ultra performance liquid chromatography ultraviolet (UV), spectroscopy, and microscopy. It is shown that photolysis is faster on leaves than on carnauba wax and that the photoprotection effect of grape wine extract is more efficient on leaves than on wax. Images recorded by microscopy bring evidence that deposits are very different on the two supports both in the absence and in the presence of the photoprotector. The grape wine extract plays a double role; it is antioxidant and UV screen. Photoprotection by the grape wine extract is a complex mixing of UV screen and antioxidant effects. The UV screen effect can be rationalized by considering the rate of light absorption by sulcotrione. Our results demonstrate that the rates of sulcotrione phototransformation are mainly governed by the repartition of the deposit on the solid support.

  12. Evolution of the Factory 1975-2006

    International Nuclear Information System (INIS)

    2006-01-01

    Since it was founded in 1973. Equipos Nucleares (ENSA) has been actively present in the nuclear market. This was the reason for its creation and for which it was organized from the very beginning, by designing a company with a nuclear structure and mentality. The author reviews the history and evolution of the Factory- more than a workshop- and describes its different stages, which were strongly affected by the unexpected evolution of a diminishing market- an inexistent market the likes to say- and also stresses the extraordinary difficulty of its work and the determination to remain in the nuclear market. He acknowledges the people and the culture of ENSA emphasizing their dedication, generosity, flexibility, training and enthusiasm, and stresses their stake in being the best and to attain excellence in the quality of supplies, meeting deadlines and customer satisfaction, identifying these as fundamental factors of the company's legacy. Having a better Factory is possible by improving its technological capability through researching and developing its processes, automating and robotizing manufacturing and inspection activities, and simplifying its operating systems. A result of these efforts is the continuous international presence as a supplier and collaborator with the world's leading designers, which has consolidated it as a reference supplier on the American market. Of not is the supply to the market of its different product lines a result of combining its design and manufacturing capabilities with its flexibility and size, all of which contribute to ENSA's wealth, diversity and appeal. ENSA is aware of the forthcoming resurgence of the new nuclear market. It is preparing for the future by renewing and upgrading its manufacturing facilities and implementing new systems techniques- Lean Manufacturing and Six Sigma-into its Annual Improvement Plans to favor and drive its technological capability and competitiveness and to respond to the increasingly demanding

  13. Proceedings of the Workshop on CP Violation at KAON Factory

    International Nuclear Information System (INIS)

    Ng, J.N.

    1989-07-01

    These proceedings contain the written version of eight talks delivered at the Workshop on CP Violation at KAON Factory. The articles contain reviews on the exploration of CP violation effects associated with the s-quark. Discussion on the use of intense kaon fluxes, which will be available at the proposed KAON Factory, are included

  14. Factory Gate Pricing: An Analysis of the Dutch Retail Distribution

    NARCIS (Netherlands)

    H.M. le Blanc; F. Cruijssen (Frans); H.A. Fleuren; M.B.M. de Koster (René)

    2004-01-01

    textabstractFactory Gate Pricing (FGP) is a relatively new phenomenon in retail distribution. Under FGP, products are no longer delivered at the retailer distribution center, but collected by the retailer at the factory gates of the suppliers. Owing to both the asymmetry in the distribution networks

  15. Factory Gate Pricing : An Analysis of the Dutch Retail Distribution

    NARCIS (Netherlands)

    Le Blanc, H.M.; Cruijssen, F.C.A.M.; Fleuren, H.A.; de Koster, M.B.M.

    2004-01-01

    Factory Gate Pricing (FGP) is a relatively new phenomenon in retail distribution.Under FGP, products are no longer delivered at the retailer distribution center, but collected by the retailer at the factory gates of the suppliers.Owing to both the asymmetry in the distribution networks (the supplier

  16. Parametric study of a target factory for laser fusion

    International Nuclear Information System (INIS)

    Sherohman, J.W.; Meier, W.R.

    1980-01-01

    An analysis of a target factory leading to the derivation of production rate equations has provided the basis for a parametric study. Rate equations describing the production of laser fusion targets have been developed for the purpose of identifying key parameters, attractive production techniques and cost scaling relationships for a commercial target factory

  17. Why and how to normalize the factorial moments of intermittency

    International Nuclear Information System (INIS)

    Peschanski, R.

    1990-01-01

    The normalization of factorial moments of intermittency, which is often the subject of controverses, is justified and (re-)derived from the general assumption of multi-Poissonian statistical noise in the production of particles at high-energy. Correction factors for the horizontal vs. Vertical analyses are derived in general cases, including the factorial multi-bin correlation moments

  18. Review of U.S. Neutrino Factory Studies

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2005-01-01

    We summarize the status of the two U.S. feasibility studies carried out by the Neutrino Factory and Muon Collider Collaboration (NFMCC) along with recent improvements to Neutrino Factory design developed during the American Physical Society (APS) Neutrino Physics Study. Suggested accelerator topics for the International Scoping Study (ISS) are also indicated

  19. Review of Hosein Aabad Sugar Factory (HASF) Wastewater and ...

    African Journals Online (AJOL)

    Sugar industry is one of the largest industries in the world. Hosein Abad sugar factory (HASF) is located in Hamadan province of Iran. The aim of this research was to evaluate the quality and quantity of wastewater of the said factory and to estimate the pollution load and its emission factor as prerequisite of the management ...

  20. Pesticides and their effects on wildlife

    Energy Technology Data Exchange (ETDEWEB)

    Driver, C.J.

    1994-07-01

    About 560 active ingredients are currently used as pesticides. Applications of these pesticides are made to agricultural lands and other areas inhabited by wildlife. Unfortunately, many agricultural-use pesticides also entail some measure of risk to organisms other than the pest species. Because testing of pesticides prior to registration cannot evaluate all the potential environmental-pesticide-wildlife/fish interactions, current methods of risk assessment do not always provide sufficient safety to nontarget organisms. This is evidenced by die-offs of fish and wildlife from applications of pesticides at environmentally {open_quotes}safe{close_quotes} rates, the linking of population declines of some species with agrochemical use, and observations of survival-threatening behavioral changes in laboratory and field animals exposed to typical field levels of pesticides. It is important to note, however, that the majority of pesticides, when properly applied, have not caused significant injury to wildlife. A brief summary of pesticide effects on wildlife and fish are presented for the common classes of pesticides in use today.

  1. The use and disposal of household pesticides

    International Nuclear Information System (INIS)

    Grey, Charlotte N.B.; Nieuwenhuijsen, Mark J.; Golding, Jean

    2005-01-01

    Most pesticides are synthetic chemicals manufactured specifically for their toxic properties to the target species, and widely used globally. Several epidemiological studies in the United States have suggested health concerns arising from the chronic exposure of young children to pesticides in the domestic environment. In the UK very little is currently known about how nonoccupational pesticides are being used or disposed of. Any use of pesticides is a potential risk factor for children's exposure, and any potential exposure is likely to be reduced by the parents' adopting precautionary behaviour when using these pesticide products. This was investigated using a sample of 147 parents from the Avon Longitudinal Study of Parents and Children cohort in and around Bristol, through an in-depth interview between August and November 2001. The results of this study add to the understanding of the underlying behaviour of parents applying pesticide products in the home environment in the UK. Pesticides are readily available, and are normally purchased in do-it-yourself shops and supermarkets and mostly disposed of in domestic waste. Safety was stated by 45% of parents to be the most important factor to consider when buying a pesticide. When buying pesticide products, labels were stated to be the most important source of information about pesticides. However, a third of parents stated they would not follow the product label exactly when using a product, just under half felt labels were both inadequate and hard to understand, and about 10% of parents would not take notice of warnings on the pesticide label. Less than half of parents would use gloves when applying a pesticide, although the use of protective equipment such as gloves during the application of pesticides could greatly reduce the exposure. It is a public health concern that the instructions on the labels of products may not always be understood or followed, and further understanding of user behaviour is needed

  2. The Three-dimensional Digital Factory for Shipbuilding Technology Research

    Directory of Open Access Journals (Sweden)

    Xu Wei

    2016-01-01

    Full Text Available The three-dimensional digital factory technology research is the hotspot in shipbuilding recently. The three-dimensional digital factory technology not only focus on design the components of the product, but also discuss on the simulation and analyses of the production process.Based on the three-dimensional model, the basic data layer, application control layer and the presentation layer of hierarchical structure are established in the three-dimensional digital factory of shipbuilding in this paper. And the key technologies of three-dimensional digital factory of shipbuilding are analysed. Finally, a case study is applied and the results show that the three-dimensional digital factory will play an important role in the future.

  3. The Experience Factory: Strategy and Practice

    Science.gov (United States)

    Basili, Victor R.; Caldiera, Gianluigi

    1995-01-01

    The quality movement, that has had in recent years a dramatic impact on all industrial sectors, has recently reached the system and software industry. Although some concepts of quality management, originally developed for other product types, can be applied to software, its specificity as a product which is developed and not produced requires a special approach. This paper introduces a quality paradigm specifically tailored on the problem of the systems and software industry. Reuse of products, processes and experiences originating from the system life cycle is seen today as a feasible solution to the problem of developing higher quality systems at a lower cost. In fact, quality improvement is very often achieved by defining and developing an appropriate set of strategic capabilities and core competencies to support them. A strategic capability is, in this context, a corporate goal defined by the business position of the organization and implemented by key business processes. Strategic capabilities are supported by core competencies, which are aggregate technologies tailored to the specific needs of the organization in performing the needed business processes. Core competencies are non-transitional, have a consistent evolution, and are typically fueled by multiple technologies. Their selection and development requires commitment, investment and leadership. The paradigm introduced in this paper for developing core competencies is the Quality Improvement Paradigm which consists of six steps: (1) Characterize the environment, (2) Set the goals, (3) Choose the process, (4) Execute the process, (5) Analyze the process data, and (6) Package experience. The process must be supported by a goal oriented approach to measurement and control, and an organizational infrastructure, called Experience Factory. The Experience Factory is a logical and physical organization distinct from the project organizations it supports. Its goal is development and support of core competencies

  4. Pesticide Environmental Accounting: a method for assessing the external costs of individual pesticide applications.

    Science.gov (United States)

    Leach, A W; Mumford, J D

    2008-01-01

    The Pesticide Environmental Accounting (PEA) tool provides a monetary estimate of environmental and health impacts per hectare-application for any pesticide. The model combines the Environmental Impact Quotient method and a methodology for absolute estimates of external pesticide costs in UK, USA and Germany. For many countries resources are not available for intensive assessments of external pesticide costs. The model converts external costs of a pesticide in the UK, USA and Germany to Mediterranean countries. Economic and policy applications include estimating impacts of pesticide reduction policies or benefits from technologies replacing pesticides, such as sterile insect technique. The system integrates disparate data and approaches into a single logical method. The assumptions in the system provide transparency and consistency but at the cost of some specificity and precision, a reasonable trade-off for a method that provides both comparative estimates of pesticide impacts and area-based assessments of absolute impacts.

  5. Citizen's Guide to Pest Control and Pesticide Safety

    Science.gov (United States)

    ... contain pesticide residues. In addition, birds such as ducks and geese may absorb pesticide residues if they ... Where do you store your pesticides? A nationwide study conducted by EPA revealed that almost half (approximately ...

  6. A mobile App for military operational entomology pesticide applications

    Science.gov (United States)

    Multiple field studies conducted for the Deployed War Fighter Protection (DWFP) research program have generated over 80 specific guidance points for innovative combinations of pesticide application equipment, pesticide formulations, and application techniques for aerosol and residual pesticide treat...

  7. How to Report a Pesticide Incident Involving Exposures to People

    Science.gov (United States)

    Pesticides incidents must be reported by pesticide registrants. Others, such as members of the public and environmental professionals, would like to report pesticide incidents. This website will facilitate such incident reporting.

  8. Pesticide registration, distribution and use practices in Ghana

    NARCIS (Netherlands)

    Onwona Kwakye, Michael; Mengistie, Belay; Ofosu-Anim, John; Nuer, Alexander Tetteh K.; Den Brink, van Paul J.

    2018-01-01

    Ghana has implemented regulation on the registration, distribution and usage of pesticides in order to evaluate their environmental and human health effects. However, environmental monitoring and certified laboratories for pesticide analysis are lacking. Pesticide misuse, misapplication,

  9. The factorial structure of pathological gambling.

    Science.gov (United States)

    Steel, Z; Blaszczynski, A

    1996-03-01

    Pathological gambling has been characterised by DSM-III-R and DSM-IV as a disorder of impulse control with a proportion of gamblers identified as meeting criteria for a co-morbid diagnosis of Antisocial Personality Disorder. To date, empirical evidence in support of the notion that pathological gamblers as a group manifest elevated traits of impulsivity remains equivocal. Principal components analysis was used to investigate relationships between the constructs of impulsivity, psychopathy, DSM-III-R criteria for Antisocial Personality Disorder, psychological distress, criminal offending behavior and a range of other common psychological measures employed with pathological gamblers. The sample comprised 115 pathological gamblers, 80 consecutive gamblers seeking treatment from a general hospital psychiatric inpatient behavior therapy unit, and 35 volunteer Gamblers Anonymous attenders. Four primary factors were determined: psychological distress, sensation seeking, crime and liveliness, and impulsive-antisocial. Results suggest that pathological gambling consists of a number of discrete and reproducible factorial structures. The impulsive antisocial factor was found to be associated with gambling behavior and indices of poor psychosocial functioning.

  10. Hospitals as factories of medical garbage.

    Science.gov (United States)

    Hodges, Sarah

    2017-12-01

    Over the course of the twentieth century, as hospitals cleaned up, they came to produce more and more rubbish. Beginning in the 1970s and gaining pace in the 1980s and 1990s, single-use plastic items (syringes, blood bags, tubing) saturated everyday medical practice across the globe. This essay brings the question of plastic to bear upon the longer history of twentieth century sanitary science. The widespread adoption of single-use disposable medical plastics consolidated a century's worth of changes in medical hygiene. As strange as it may seem today, the initial uptake of medical plastics was not driven primarily by concerns about hygiene. Plastic began as a mid-century technology of convenience and durability. It was not until the end of the twentieth century that it morphed into a powerful symbol and instrument of medical hygiene. Today, both patients and practitioners have embraced plastic as an indispensable technology of clean medicine. The procession of single-use medical plastics through everyday medicine now comprises a constant, if disposable, infrastructure of medical hygiene. This new processional infrastructure of disposable hygiene has produced another, albeit unintended, consequence. This new regime has exponentially increased hospitals' material outputs. In so doing, plastic has refigured the ecologies of everyday medicine. Plastic hygiene has rendered hospitals factories of medical garbage.

  11. New Physics at a Super Flavor Factory

    CERN Document Server

    Browder, Thomas E; Pirjol, Dan; Soni, Amarjit; Zupan, Jure

    2009-01-01

    The potential of a Super Flavor Factory (SFF) for searches of New Physics is reviewed. While very high luminosity B physics is assumed to be at the core of the program, its scope for extensive charm and tau studies are also emphasized. The possibility to run at the Upsilon(5S) as well as at the Upsilon(4S) is also very briefly discussed; in principle, this could provide very clean measurements of B_s decays. The strength and reach of a SFF is most notably due to the possibility of examining an impressive array of very clean observables. The angles and the sides of the unitarity triangle can be determined with unprecedented accuracy. These serve as a reference for New Physics (NP) sensitive decays such as B^+ ->tau^+ nu and penguin dominated hadronic decay modes, providing tests of generic NP scenarios with an accuracy of a few percent. Besides, very precise studies of direct and time dependent CP asymmetries in radiative B decays and forward-backward asymmetry studies in B -> X_s l^+ l^- and numerous null tes...

  12. Shielding design of RIKEN RI Beam Factory

    Energy Technology Data Exchange (ETDEWEB)

    Uwamino, Yoshitomo; Fukunishi, Nobuhisa [Institute of Physical and Chemical Research, Wako, Saitama (Japan); Oishi, Koji [Shimizu Corp., Tokyo (Japan)

    2000-03-01

    Construction of the RIKEN RI Beam Factory is started, and the phase 1 will be finished by the end of March 2003. Two ring cyclotrons including one superconducting machine and two Big RIPSs will be constructed in the phase 1. Heavy ions of proton to uranium will be accelerated up to 400 MeV/u (A<40) and 150 MeV/u for uranium at an intensity of 10{sup 13} pps. Neutron production by the 400 MeV/u {sup 20}Ne beam was measured at HIMAC of NIRS and it was used for the source term of the shielding calculations. The deep penetration of high-energy neutrons was calculated by using the ANISN code with the DLC-119/HILO86R group constants and also by using the HETC code. The ANISN results were modified by using the HETC results and the shielding experiment at ISIS, and they were fitted by a simple formula for practical use. High-energy neutron penetrations of slantwise injection and the reflection probabilities of iron slab were calculated with the HETC code, and these results were used for the estimation of the thickness for the iron local shielding of Big RIPSs. Induced radioactivity in the air, accelerator components and the building, and the skyshine effect were also estimated. (author)

  13. The Gamma Factory proposal for CERN

    CERN Document Server

    Krasny, Mieczyslaw Witold

    2015-01-01

    This year, 2015, marks the centenary of the publication of Einsteins Theory of General Relativity and it has been named the International Year of Light and light-based technologies by the UN General Assembly. It is thus timely to discuss the possibility of broadening the present CERN research program by including a new component based on a novel concept of the light source which could pave a way towards a multipurpose Gamma Factory. The proposed light source could be realized at CERN by using the infrastructure of the existing accelerators. It could push the intensity limits of the presently operating light-sources by at least 7 orders of magnitude, reaching the flux of the order of 10^17 photons/s, in the particularly interesting gamma-ray energy domain of 1 < Ephoton < 400 MeV. This domain is out of reach for the FEL-based light sources. The energy-tuned, quasi-monochromatic gamma beams, together with the gamma-beam-driven, high intensity secondary beams of polarized positrons, polarized muons, neutro...

  14. Multiple exposure routes of a pesticide exacerbate effects on a grazing mayfly.

    Science.gov (United States)

    Pristed, Mathias Joachim Skov; Bundschuh, Mirco; Rasmussen, Jes Jessen

    2016-09-01

    Hydrophobic pesticides such as pyrethroid insecticides tend to occur in their soluble form mainly as transient pulses in streams. In addition, they are regularly detected in significant quantities adsorbed to stream sediments and other organic in-stream structures. Consequently, stream biota is likely subjected to pesticide exposure via multiple routes. In this study we aimed at investigating the influence of exposure routes for the pyrethroid insecticide lambda-cyhalothrin on the grazing mayfly Heptagenia sulphurea. Therefore, H. sulphurea was exposed to lambda-cyhalothrin via single- (water or biofilm) or biphasic exposure (water and biofilm) at environmentally realistic concentrations (0, 0.1, 1μgL(-1)) and exposure duration (2h) in a full factorial design (n=5). Mortality, moulting frequency, and biofilm accrual (proxy for feeding rate) were recorded subsequent to a 7 d post exposure period. Mortality significantly increased and moulting frequency significantly decreased with increasing concentrations of lambda-cyhalothrin in the water phase whereas exposure via biofilm prompted no significant effects on these endpoints (α=0.05). Effect predictions systematically underestimated and overestimated effects for mortality and moulting frequency, respectively. Similarly, mayfly feeding rate was significantly reduced by water phase exposure whereas pre-exposed biofilm did not significantly affect this variable. However, we found a significant but non-systematic interaction between water phase and biofilm exposure on mayfly feeding rate. Our results show that exposure to the same pesticide via multiple exposure routes may increase the magnitude of effects beyond the level predicted from single phase exposures which has clear implications for the aquatic risk assessment of hydrophobic pesticides. However, our results additionally reveal that interactions between pesticide exposure routes may vary between selected dependent variables. We emphasize that unravelling the

  15. Removal of Pesticides From Water by Nanofiltration

    OpenAIRE

    RIUNGU, N J; HESAMPOUR, M; PIHLAJAMAKI, A; MANTTARI, M; home, P G; NDEGWA, G M

    2012-01-01

    Agricultural activities form the backborne of Kenyas economy. Inorder to control crop losses, pesticides are used and in the recent past, more of the pesticides have been used to increase production. However, the effect of pesticides on the environment is very complex as undesirable transfers occur continually among different environmental sections. This eventually leads to contamination of drinking water source especially for rivers and lakes located near active agriculture practices especia...

  16. Determination of Pesticide Residues in Cannabis Smoke

    OpenAIRE

    Nicholas Sullivan; Sytze Elzinga; Jeffrey C. Raber

    2013-01-01

    The present study was conducted in order to quantify to what extent cannabis consumers may be exposed to pesticide and other chemical residues through inhaled mainstream cannabis smoke. Three different smoking devices were evaluated in order to provide a generalized data set representative of pesticide exposures possible for medical cannabis users. Three different pesticides, bifenthrin, diazinon, and permethrin, along with the plant growth regulator paclobutrazol, which are readily available...

  17. Reduction of substituted benzonitrile pesticides

    Czech Academy of Sciences Publication Activity Database

    Sokolová, Romana; Hromadová, Magdaléna; Fiedler, Jan; Pospíšil, Lubomír; Giannarelli, S.; Valášek, Michal

    2008-01-01

    Roč. 622, č. 2 (2008), s. 211-218 ISSN 1572-6657 R&D Projects: GA AV ČR IAA400400505; GA MŠk OC 140; GA MŠk LC510 Institutional research plan: CEZ:AV0Z40400503; CEZ:AV0Z40550506 Keywords : benzonitrile pesticides * polarography * voltammetry Subject RIV: CG - Electrochemistry Impact factor: 2.484, year: 2008

  18. 76 FR 41246 - Pesticide Program Dialogue Committee, Pesticide Registration Improvement Act Process Improvement...

    Science.gov (United States)

    2011-07-13

    ... Committee, Pesticide Registration Improvement Act Process Improvement Workgroup; Notice of Public Meeting...) Process Improvement Work Group. EPA plans to meet its ESA consultation obligations through the pesticide... a pesticide during the registration review process. This meeting of the PRIA Process Improvement...

  19. Pesticides: Benefaction or Pandora's Box? A synopsis of the environmental aspects of 243 pesticides

    NARCIS (Netherlands)

    Linders JBHJ; Jansma JW; Mensink BJWG; Otermann K; ACT

    1994-01-01

    The report provides an overview of physical, chemical and environmental data of 243 pesticides. The data mentioned are based on confidential information supplied by the manufacturers of the pesticides. For all pesticides mentioned a Final Environmental File, which is public, is derived. Tables with

  20. Occupational Pesticide Exposures and Respiratory Health

    Science.gov (United States)

    Ye, Ming; Beach, Jeremy; Martin, Jonathan W.; Senthilselvan, Ambikaipakan

    2013-01-01

    Pesticides have been widely used to control pest and pest-related diseases in agriculture, fishery, forestry and the food industry. In this review, we identify a number of respiratory symptoms and diseases that have been associated with occupational pesticide exposures. Impaired lung function has also been observed among people occupationally exposed to pesticides. There was strong evidence for an association between occupational pesticide exposure and asthma, especially in agricultural occupations. In addition, we found suggestive evidence for a link between occupational pesticide exposure and chronic bronchitis or COPD. There was inconclusive evidence for the association between occupational pesticide exposure and lung cancer. Better control of pesticide uses and enforcement of safety behaviors, such as using personal protection equipment (PPE) in the workplace, are critical for reducing the risk of developing pesticide-related symptoms and diseases. Educational training programs focusing on basic safety precautions and proper uses of personal protection equipment (PPE) are possible interventions that could be used to control the respiratory diseases associated with pesticide exposure in occupational setting. PMID:24287863

  1. Sorption of pesticides to aquifer minerals

    DEFF Research Database (Denmark)

    Clausen, Liselotte; Fabricius, Ida Lykke

    2000-01-01

    This paper summarizes results from a work were the sorption of five pesticides on seven minerals were studied in order to quantify the adsorption to different mineral surfaces. Investigated mineral phases are: quartz, calcite, kaolinite, a-alumina, and three iron oxides (2-line ferrihydrite......, goethite, lepidocrocite). Selected pesticides are: atrazine, isoproturon, mecoprop, 2,4-D, and bentazone. The results demonstrate that pesticides adsorb to pure mineral surfaces. However, the size of the adsorption depends on the type of pesticide and the type of mineral....

  2. Effect of Endocrine Disruptor Pesticides: A Review

    Directory of Open Access Journals (Sweden)

    Benoit Roig

    2011-06-01

    Full Text Available Endocrine disrupting chemicals (EDC are compounds that alter the normal functioning of the endocrine system of both wildlife and humans. A huge number of chemicals have been identified as endocrine disruptors, among them several pesticides. Pesticides are used to kill unwanted organisms in crops, public areas, homes and gardens, and parasites in medicine. Human are exposed to pesticides due to their occupations or through dietary and environmental exposure (water, soil, air. For several years, there have been enquiries about the impact of environmental factors on the occurrence of human pathologies. This paper reviews the current knowledge of the potential impacts of endocrine disruptor pesticides on human health.

  3. 76 FR 63298 - Pesticide Products; Registration Applications

    Science.gov (United States)

    2011-10-12

    ... each contact person is: Biopesticides and Pollution Prevention Division, Office of Pesticide Programs...: October 3, 2011. Keith A Matthews, Director, Biopesticides and Pollution Prevention Division, Office of...

  4. 75 FR 6656 - Pesticide Product; Registration Application

    Science.gov (United States)

    2010-02-10

    ... (703) 305-5805. FOR FURTHER INFORMATION CONTACT: Shanaz Bacchus, Biopesticides and Pollution Prevention... protection, Pesticides and pests. Dated: January 29, 2010. Keith A. Matthews, Acting Director, Biopesticides...

  5. Survivor shielding. Part A. Nagasaki factory worker shielding

    International Nuclear Information System (INIS)

    Santoro, Robert T.; Barnes, John M.; Azmy, Yousry Y.; Kerr, George D.; Egbert, Stephen D.; Cullings, Harry M.

    2005-01-01

    Recent investigations based on conventional chromosome aberration data by the RERF suggest that the DS86 doses received by many Nagasaki factory workers may have been overestimated by as much as 40% relative to those for other survivors in Japanese-type houses and other shielding configurations (Kodama et al. 2001). Since the factory workers represent about 25% of the Nagasaki survivors with DS86 doses in excess of 0.5 Gy (50 rad), systematic errors in their dose estimates can have a major impact on the risk coefficients from RERF studies. The factory worker doses may have been overestimated for a number of reasons. The calculation techniques, including the factory building modeling, weapon source spectra and cross-section data used in the DS86 shielding calculations were not detailed enough to replicate actual conditions. The models used did not take into account local shielding provided by machinery, tools, and the internal structure in the buildings. In addition, changes in the disposition of shielding following collapse of the building by the blast wave were not considered. The location of large factory complexes may be uncertain, causing large numbers of factory survivors, correctly located relative to each other, to be uniformly too close to the hypocenter. Any or all of these reasons are sufficient to result in an overestimate of the factory worker doses. During the DS02 studies, factory worker doses have been reassessed by more carefully modeling the factory buildings, incorporating improved radiation transport methods and cross-section data and using the most recent bomb leakage spectra (Chapter 2). Two-dimensional discrete ordinates calculations were carried out initially to estimate the effects of workbenches and tools on worker doses to determine if the inclusion of these components would, in fact, reduce the dose by amounts consistent with the RERF observations (Kodama et al. 2001). (author)

  6. Dioxin/POPs legacy of pesticide production in Hamburg: part 1--securing of the production area.

    Science.gov (United States)

    Weber, Roland; Varbelow, Hans Gerhard

    2013-04-01

    α-Hexachlorocyclohexane (HCH), β-HCH, and γ-HCH (lindane) were recently included as new persistent organic pollutants (POPs) in the Stockholm Convention. Therefore, the chemicals need to be globally addressed, including the disposal of historic wastes. At most sites, the approximately 85% of HCH waste isomers were dumped. At a former lindane factory in Hamburg and some other factories the HCH, waste was recycled producing residues with high polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/PCDF) levels. The soil and ground water under the former pesticide factory was/is highly contaminated with HCH (260 tons), chlorobenzenes (550 tons), and PCDD/PCDF (6 kg toxic equivalents (TEQ)). This contamination did not result from disposal operations but from spillages and leakages during the 30 years of the factory's production history. A containment wall has been constructed around the production area to prevent the dispersal of the pollutants. The ground water is managed by a pump and treat system. Over the last 15 years, approximately 10-30 tons of this pollution reservoir has been pumped and incinerated. For the contaminated production buildings, specific assessment and demolition technologies have been applied. In addition to their HCH waste isomer deposition, former lindane/HCH productions need to be assessed for possible recycling practice of HCH and related PCDD/PCDF contamination of the production area and buildings. Since such recycling activities have taken place at several factories in different countries, the experience of assessment and management of the described production area and contaminated buildings could be valuable. Such assessment could be addressed within the frame of the Stockholm Convention.

  7. Make your company a talent factory.

    Science.gov (United States)

    Ready, Douglas A; Conger, Jay A

    2007-06-01

    Despite the great sums of money companies dedicate to talent management systems, many still struggle to fill key positions - limiting their potential for growth in the process. Virtually all the human resource executives in the authors' 2005 survey of 40 companies around the world said that their pipeline of high-potential employees was insufficient to fill strategic management roles. The survey revealed two primary reasons for this. First, the formal procedures for identifying and developing next-generation leaders have fallen out of sync with what companies need to grow or expand into new markets. To save money, for example, some firms have eliminated positions that would expose high-potential employees to a broad range of problems, thus sacrificing future development opportunities that would far outweigh any initial savings from the job cuts. Second, HR executives often have trouble keeping top leaders' attention on talent issues, despite those leaders' vigorous assertions that obtaining and keeping the best people is a major priority. If passion for that objective doesn't start at the top and infuse the culture, say the authors, talent management can easily deteriorate into the management of bureaucratic routines. Yet there are companies that can face the future with confidence. These firms don't just manage talent, they build talent factories. The authors describe the experiences of two such corporations - consumer products icon Procter & Gamble and financial services giant HSBC Group -that figured out how to develop and retain key employees and fill positions quickly to meet evolving business needs. Though each company approached talent management from a different direction, they both maintained a twin focus on functionality (rigorous talent processes that support strategic and cultural objectives) and vitality (management's emotional commitment, which is reflected in daily actions).

  8. The Experiment Factory: standardizing behavioral experiments

    Directory of Open Access Journals (Sweden)

    Vanessa V Sochat

    2016-04-01

    Full Text Available The administration of behavioral and experimental paradigms for psychology research is hindered by lack of a coordinated effort to develop and deploy standardized paradigms. While several frameworks (de Leeuw (2015; McDonnell et al. (2012; Mason and Suri (2011; Lange et al. (2015 have provided infrastructure and methods for individual research groups to develop paradigms, missing is a coordinated effort to develop paradigms linked with a system to easily deploy them. This disorganization leads to redundancy in development, divergent implementations of conceptually identical tasks, disorganized and error-prone code lacking documentation, and difficulty in replication. The ongoing reproducibility crisis in psychology and neuroscience research (Baker (2015; Open Science Collaboration (2015 highlights the urgency of this challenge: reproducible research in behavioral psychology is conditional on deployment of equivalent experiments. A large, accessible repository of experiments for researchers to develop collaboratively is most efficiently accomplished through an open source framework. Here we present the Experiment Factory, an open source framework for the development and deployment of web-based experiments. The modular infrastructure includes experiments, virtual machines for local or cloud deployment, and an application to drive these components and provide developers with functions and tools for further extension. We release this infrastructure with a deployment (http://www.expfactory.org that researchers are currently using to run a set of over 80 standardized web-based experiments on Amazon Mechanical Turk. By providing open source tools for both deployment and development, this novel infrastructure holds promise to bring reproducibility to the administration of experiments, and accelerate scientific progress by providing a shared community resource of psychological paradigms.

  9. Overview of the nearby supernova factory

    International Nuclear Information System (INIS)

    Aldering, Greg; Adam, Gilles; Antilogus, Pierre; Astier, Pierre; Bacon, Roland; Bongard, S.; Bonnaud, C.; Copin, Yannick; Hardin, D.; Howell, D. Andy; Lemmonnier, Jean-Pierre; Levy, J.-M.; Loken, S.; Nugent, Peter; Pain, Reynald; Pecontal, Arlette; Pecontal, Emmanuel; Perlmutter, Saul; Quimby, Robert; Schahmaneche, Kyan; Smadja, Gerard; Wood-Vasey, W. Michael

    2002-01-01

    The Nearby Supernova Factory (SNfactory) is an international experiment designed to lay the foundation for the next generation of cosmology experiments (such as CFHTLS, wP, SNAP and LSST) which will measure the expansion history of the Universe using Type Ia supernovae. The SNfactory will discover and obtain frequent lightcurve spectrophotometry covering 3200-10000 (angstrom) for roughly 300 Type Ia supernovae at the loW--redshift end of the smooth Hubble flow. The quantity, quality, breadth of galactic environments, and homogeneous nature of the SNfactory dataset will make it the premier source of calibration for the Type Ia supernova width-brightness relation and the intrinsic supernova colors used for K-correction and correction for extinction by host-galaxy dust. This dataset will also allow an extensive investigation of additional parameters which possibly influence the quality of Type Ia supernovae as cosmological probes. The SNfactory search capabilities and folloW--up instrumentation include wide-field CCD imagers on two 1.2-m telescopes (via collaboration with the Near Earth Asteroid Tracking team at JPL and the QUEST team at Yale), and a two-channel integral-field-unit optical spectrograph/imager being fabricated for the University of Hawaii 2.2-m telescope. In addition to ground-based folloW--up, UV spectra for a subsample of these supernovae will be obtained with HST. The pipeline to obtain, transfer via wireless and standard internet, and automatically process the search images is in operation. Software and hardware development is now underway to enable the execution of folloW--up spectroscopy of supernova candidates at the Hawaii 2.2-m telescope via automated remote control of the telescope and the IFU spectrograph/imager

  10. PEP-II: An asymmetric B factory

    International Nuclear Information System (INIS)

    1993-06-01

    In this report, the authors have described an updated conceptual design for the high-luminosity Asymmetric B Factory (PEP-II) to be built in the PEP tunnel culmination of more than four years of effort aimed at the design and construction of an asymmetric e + e - collider capable of achieving a luminosity of L = 3 x 10 33 cm -2 s -1 . All aspects of the conceptual design were scrutinized in March 1991 by a DOE technical review committee chaired by Dr. L. Edward Temple. The design was deemed feasible and capable of achieving its physics goals. Furthermore, the cost estimate, schedule, and management plan for the project were fully endorsed by the committee. This updated conceptual design report captures the technical progress since the March 1991 review and reflects the lower cost estimate corresponding to the improved design. Although the PEP-II design has continued to evolve, no technical scope changes have been made that invalidate the conclusion of the DOE review. The configuration adopted utilizes two storage rings, an electron ring operating at 9 GeV and a positron ring at 3.1 GeV, each with a circumference of 2200 m. The high-energy ring is an upgrade of the PEP storage ring at SLAC; all PEP magnets and most power supplies will be reused. The upgrade consists primarily of replacing the PEP vacuum chamber and RF system with newly designed versions optimized for the high-current environment of PEP-II. The low-energy ring will be newly constructed and will be situated atop the high-energy ring in the PEP tunnel. Utilities already installed in the PEP tunnel are largely sufficient to operate the two PEP-II storage rings

  11. Pesticide regulations and farm worker safety: the need to improve pesticide regulations in Viet Nam.

    Science.gov (United States)

    Phung, Dung Tri; Connell, Des; Miller, Greg; Rutherford, Shannon; Chu, Cordia

    2012-06-01

    Agricultural pesticide use in Viet Nam has more than tripled since 1990. However, pesticide legislation and regulations have not been developed in response to this large increase in usage, as a result of which pesticides pose a serious threat to human health and the environment. This paper identifies the need to improve pesticide regulations in Viet Nam through a comparative analysis of pesticide regulations in Viet Nam and the United States of America, where the rate of acute poisoning among agricultural workers is much lower than in Viet Nam and where information pertaining to pesticide regulations is made accessible to the public. The analysis identified several measures that would help to improve Viet Nam's pesticide regulations. These include enhancing pesticide legislation, clarifying the specific roles and active involvement of both the environmental and health sectors; performing a comprehensive risk-benefit evaluation of pesticide registration and management practices; improving regulations on pesticide suspension and cancellation, transport, storage and disposal; developing import and export policies and enhancing pesticide-related occupational safety programmes.

  12. Pattern of pesticide storage before pesticide self-poisoning in rural Sri Lanka

    DEFF Research Database (Denmark)

    Mohamed, Fahim; Manuweera, Gamini; Gunnell, David

    2009-01-01

    BACKGROUND: Deliberate self-poisoning with agricultural pesticides is the commonest means of suicide in rural Asia. It is mostly impulsive and facilitated by easy access to pesticides. The aim of this large observational study was to investigate the immediate source of pesticides used for self......-harm to help inform suicide prevention strategies such as reducing domestic access to pesticides. METHODS: The study was conducted in a district hospital serving an agricultural region of Sri Lanka. Patients who had self-poisoned with pesticides and were admitted to the adult medical wards were interviewed...... the particular pesticide for self-harm were its easy accessibility (n = 311, 46%) or its popularity as a suicide agent in their village (n = 290, 43%). CONCLUSION: Three quarters of people who ingested pesticides in acts of self-harm used products that were available within the home or in close proximity...

  13. Neutrino Factory Accelerator R and D: Status and Priorities

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2005-01-01

    This paper summarizes the status of worldwide Neutrino Factory R and D efforts. Activities are categorized as simulations, component development, and system tests. An indication of R and D tasks that remain to be accomplished is also given

  14. Training Workers for the Factory of the Future.

    Science.gov (United States)

    Clancy, J. Anthony

    1989-01-01

    In the factory of the future, emphasis on quality and increased productivity creates a competitive advantage. People and computers work together in all major activities. Training is a major factor in creating that competitive advantage. (JOW)

  15. Three-dimensional structure of Rubella virus factories

    International Nuclear Information System (INIS)

    Fontana, Juan; Lopez-Iglesias, Carmen; Tzeng, Wen-Ping; Frey, Teryl K.; Fernandez, Jose J.; Risco, Cristina

    2010-01-01

    Viral factories are complex structures in the infected cell where viruses compartmentalize their life cycle. Rubella virus (RUBV) assembles factories by recruitment of rough endoplasmic reticulum (RER), mitochondria and Golgi around modified lysosomes known as cytopathic vacuoles or CPVs. These organelles contain active replication complexes that transfer replicated RNA to assembly sites in Golgi membranes. We have studied the structure of RUBV factory in three dimensions by electron tomography and freeze-fracture. CPVs contain stacked membranes, rigid sheets, small vesicles and large vacuoles. These membranes are interconnected and in communication with the endocytic pathway since they incorporate endocytosed BSA-gold. RER and CPVs are coupled through protein bridges and closely apposed membranes. Golgi vesicles attach to the CPVs but no tight contacts with mitochondria were detected. Immunogold labelling confirmed that the mitochondrial protein p32 is an abundant component around and inside CPVs where it could play important roles in factory activities.

  16. PARTICLE FACTORIES: Tau-charm in the spotlight

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1991-07-15

    Following earlier workshops in Stanford (1989) and in Orsay (1990), some hundred physicists from Europe and the United States met from 29 April to 2 May in Seville, Spain, to consolidate plans for a Tau-Charm Factory.

  17. Measurement of CP violation at a Neutrino Factory

    CERN Document Server

    Gómez-Cadenas, J J

    2001-01-01

    The prospects of measuring CP violation in the leptonic sector using the intense neutrino beams arising from muon decay in the straight sections of a muon accumulator ring (the so-called neutrino factory) are discussed.

  18. Argonne Tau-charm factory collider design study

    International Nuclear Information System (INIS)

    Teng, L.C.; Crosbie, E.A.; Norem, J.

    1995-01-01

    The design approach and design principles for a Tau-charm Factory at Argonne were studied. These studies led to a set of preliminary parameters and tentative component features as presented in this paper

  19. PARTICLE FACTORIES: Tau-charm in the spotlight

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    Following earlier workshops in Stanford (1989) and in Orsay (1990), some hundred physicists from Europe and the United States met from 29 April to 2 May in Seville, Spain, to consolidate plans for a Tau-Charm Factory

  20. Review of Hosein Aabad Sugar Factory (HASF) Wastewater and ...

    African Journals Online (AJOL)

    MICHAEL HORSFALL

    evaluate the quality and quantity of wastewater of the said factory and to estimate the pollution ... appropriate for artificial recharge use, discharge in rivers and lakes or utilization in agriculture ..... These problems have a negative impact on.

  1. Fluorine in plants in the areas of Yugoslav aluminum factories

    Energy Technology Data Exchange (ETDEWEB)

    Ivos, J.; Ciszek, H.; Rezek, A.; Marjanovic, L.

    1970-01-01

    Distribution of fluorine in the areas around aluminum production facilities was investigated. The plants in areas around the factories did indeed show increased levels of fluorine. Distribution patterns were found to be affected by wind and precipitation patterns.

  2. Architectural design of experience based factory model for software ...

    African Journals Online (AJOL)

    architectural design. Automation features are incorporated in the design in which workflow system and intelligent agents are integrated, and the facilitation of cloud environment is empowered to further support the automation. Keywords: architectural design; knowledge management; experience factory; workflow;

  3. Argonne Tau-charm Factory collider design study

    International Nuclear Information System (INIS)

    Teng, L.C.; Crosbie, E.A.; Norem, J.; Repond, J.

    1996-01-01

    The design approach and design principles for a Tau-charm Factory at Argonne were studied. These studies led to a set of preliminary parameters and tentative component features as presented in this paper. copyright 1996 American Institute of Physics

  4. Mainz/PSI φ-factory design considerations

    International Nuclear Information System (INIS)

    Streun, A.

    1991-01-01

    Design considerations for a φ-factory with a Luminosity of the order of 10 33 cm -2 s -1 lead to the concept of a multi-bunch round beam double storage ring with superconducting solenoids for micro-beta focusing and beam rotation. Simulations of the beam-beam-interaction indicate, that significantly higher beam-beam-parameters may become possible with round beams. A rough draft design of a round beam φ-factory is presented. (orig.)

  5. Synchronous method and engineering tool for the strategic factory planning

    OpenAIRE

    Abdul Rahman, O.; Jaeger, J.; Constantinescu, C.

    2011-01-01

    This paper presents the approach to combine two reference methods and engineering tools, for "Factory Performance and Investment Planning«as well as "Value Added Ideal Production Network Planning". The resulted synchronous method aims to support factories in the strategic planning as well as in the network planning. The corresponding engineering tool is employed for assessment planning, sales planning, capacity planning and production costs planning under the consideration of dynamic and stoc...

  6. Russian factory inspection (1882-1918): cui bono?

    OpenAIRE

    Volodin , Andrei Y.

    2008-01-01

    This study deals with history of important state institution in late Russian Empire - factory inspection. Such aspects of institutional development as evolution of legislative regulations, growth of staff, and complication of functions (and particularly, mediation in labour conflicts) are scrutinized. This paper presents some results on Russian experience of labour law implementation seeking to determine and evaluate the role and efficiency of Russian factory inspectors in conflicting triangl...

  7. Development of Rotational Smart Lighting Control System for Plant Factory

    OpenAIRE

    Won-Sub Lee; Sung-Gaun Kim

    2012-01-01

    Rotational Smart Lighting Control System can supply the quantity of lighting which is required to run plants by rotating few LED and Fluorescent instead of that are used in the existing plant factories.The initial installation of the existing plants factory is expensive, so in order to solve the problem with smart lighting control system was developed. The beam required intensity for the growth of crops, Photosynthetic Photon Flux Density(PPFD)is calculated; and the numbe...

  8. Factorial moment and fractal analysis of γ families

    International Nuclear Information System (INIS)

    Kalmakhelidze, M.Eh.; Roinishvili, N.N.; Svanidze, M.S.; Khizanishvili, L.A.; Chadranyan, L.Kh.

    1997-01-01

    Factorial and fractal methods were applied to nuclear-electromagnetic cascades in the atmosphere (γ families) to find sensitivity of these methods to multiparticle fluctuations in γ families. Averaged parameters of factorial and fractal methods of the real families were compared with the same quantities for the statistical set of random families. The correlations between the same parameters for families divided into sectors and into rings are studied. The correlations between different parameters for the same families divided into sectors are investigated

  9. Virtual Factory Framework for Supporting Production Planning and Control.

    Science.gov (United States)

    Kibira, Deogratias; Shao, Guodong

    2017-01-01

    Developing optimal production plans for smart manufacturing systems is challenging because shop floor events change dynamically. A virtual factory incorporating engineering tools, simulation, and optimization generates and communicates performance data to guide wise decision making for different control levels. This paper describes such a platform specifically for production planning. We also discuss verification and validation of the constituent models. A case study of a machine shop is used to demonstrate data generation for production planning in a virtual factory.

  10. Pattern of pesticide storage before pesticide self-poisoning in rural Sri Lanka

    Science.gov (United States)

    Mohamed, Fahim; Manuweera, Gamini; Gunnell, David; Azher, Shifa; Eddleston, Michael; Dawson, Andrew; Konradsen, Flemming

    2009-01-01

    Background Deliberate self-poisoning with agricultural pesticides is the commonest means of suicide in rural Asia. It is mostly impulsive and facilitated by easy access to pesticides. The aim of this large observational study was to investigate the immediate source of pesticides used for self-harm to help inform suicide prevention strategies such as reducing domestic access to pesticides. Methods The study was conducted in a district hospital serving an agricultural region of Sri Lanka. Patients who had self-poisoned with pesticides and were admitted to the adult medical wards were interviewed by study doctors following initial resuscitation to identify the source of pesticides they have ingested. Results Of the 669 patients included in the analysis, 425 (63.5%) were male; the median age was 26 (IQR 20-36). In 511 (76%) cases, the pesticides had been stored either inside or immediately outside the house; among this group only eight patients obtained pesticides that were kept in a locked container. Ten percent (n = 67) of the patients used pesticides stored in the field while 14% (n = 91) purchased pesticides from shops within a few hours of the episode. The most common reasons for choosing the particular pesticide for self-harm were its easy accessibility (n = 311, 46%) or its popularity as a suicide agent in their village (n = 290, 43%). Conclusion Three quarters of people who ingested pesticides in acts of self-harm used products that were available within the home or in close proximity; relatively few patients purchased the pesticide for the act. The study highlights the importance of reducing the accessibility of toxic pesticides in the domestic environment. PMID:19889236

  11. Public health effects of pesticides used in pest management and precautions for the protection

    Directory of Open Access Journals (Sweden)

    Mustafa Alparslan Babayigit

    2014-10-01

    Full Text Available Pesticides, which are widely used not only for weed and pest control efforts in agricultural sector but also preservatives and antifouling for factory products, consumer products such as household disinfectants and food packaging and storage operations, can be detected both from the basic components of the environment and all living tissues. Due to the toxic effects, they can lead to many chronic irreversible diseases such as cancer, defective births, nervous system disorders, endocrine system disorders including diabetes. Not only the risk groups in the community including children, the elderly, pregnant women, and particularly the agricultural sector workers, who have high risk of exposure to pesticides, but also all the individuals in the community must be protected against the harmful effects of pesticides. For this reason, when fighting against the pests, integrated pest management principles, which primarily targets not damaging the humans and community as well as the environment and other organisms, should be based on. [TAF Prev Med Bull 2014; 13(5.000: 405-412

  12. The Impact of Pesticides on Honey Bees and Hence on Humans

    Directory of Open Access Journals (Sweden)

    Antonina Jivan

    2013-05-01

    Full Text Available Bee crisis is threatening global food security, given the fact that one third of global agricultural production relies on pollination, especially that of honey bees. Despite their importance for human being, honey bees die with alarming speed. In recent years, in Europe and America, due to pollution, pesticides and neglect there was registered an unprecedented rate of disappearance of honey bees. Einstein's theory, the fact that once the bees cease to exist, humanity has only four years to extinction, seems now truer than ever. Thus, the issue has gained a tone of maximum urgency; the bee crisis can entirely shatter the world food security, already affected by the economic crisis. There are plenty of factors that could cause honey bee population decline: disease, parasites, climatic factors (high temperature, drought or decrease in the diversity of honey flora. It may sometimes happen that the beekeeper himself causes the poisoning of his honey bees, use inappropriate products which should protect the honey bees. It is therefore possible to imagine a multi-factorial explanation of problems encountered by honey bees and to underestimate the key role of pesticides. Considering these, a review of the impact of pesticides on honey bees should not be superfluous.

  13. 33 CFR 274.4 - Pesticide management.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Pesticide management. 274.4... DEFENSE PEST CONTROL PROGRAM FOR CIVIL WORKS PROJECTS Project Operation § 274.4 Pesticide management. (a... control management personnel prior to advertisement of the contract and procurement of services. The...

  14. Modeling pesticide risk to California gnatcatchers

    Science.gov (United States)

    Pesticides are used widely in US agriculture and may affect non-target organisms, including birds. Recently, USEPA has worked with other federal agencies, including USFWS and NMFS, to revise and strengthen methods for conducting pesticide risk assessments under section 7 of the U...

  15. Reproductive disorders associated with pesticide exposure.

    Science.gov (United States)

    Frazier, Linda M

    2007-01-01

    Exposure of men or women to certain pesticides at sufficient doses may increase the risk for sperm abnormalities, decreased fertility, a deficit of male children, spontaneous abortion, birth defects or fetal growth retardation. Pesticides from workplace or environmental exposures enter breast milk. Certain pesticides have been linked to developmental neurobehavioral problems, altered function of immune cells and possibly childhood leukemia. In well-designed epidemiologic studies, adverse reproductive or developmental effects have been associated with mixed pesticide exposure in occupational settings, particularly when personal protective equipment is not used. Every class of pesticides has at least one agent capable of affecting a reproductive or developmental endpoint in laboratory animals or people, including organophosphates, carbamates, pyrethroids, herbicides, fungicides, fumigants and especially organochlorines. Many of the most toxic pesticides have been banned or restricted in developed nations, but high exposures to these agents are still occurring in the most impoverished countries around the globe. Protective clothing, masks and gloves are more difficult to tolerate in hot, humid weather, or may be unavailable or unaffordable. Counseling patients who are concerned about reproductive and developmental effects of pesticides often involves helping them assess their exposure levels, weigh risks and benefits, and adopt practices to reduce or eliminate their absorbed dose. Patients may not realize that by the first prenatal care visit, most disruptions of organogenesis have already occurred. Planning ahead provides the best chance of lowering risk from pesticides and remediating other risk factors before conception.

  16. Toxicity of Pesticides. Agrichemical Fact Sheet 2.

    Science.gov (United States)

    Hock, Winand K.

    This fact sheet gives the acute oral and dermal toxicity (LD 50) of over 250 pesticides in lab animals. The chemicals are categorized as fungicides, herbicides, insecticides, or miscellaneous compounds. One or more trade names are given for each pesticide. In addition, a brief explanation of toxicity determination is given. (BB)

  17. Aquatic Macrophyte Risk Assessment for Pesticides

    NARCIS (Netherlands)

    Maltby, L.; Arnold, D.; Arts, G.H.P.; Davies, J.; Heimbach, F.; Pickl, C.; Poulsen, V.

    2009-01-01

    Given the essential role that primary producers play in aquatic ecosystems, it is imperative that the potential risk of pesticides to the structure and functioning of aquatic plants is adequately assessed. This book discusses the assessment of the risk of pesticides with herbicidal activity to

  18. 75 FR 56105 - Pesticide Products; Registration Applications

    Science.gov (United States)

    2010-09-15

    ... Products, Inc., 2625 South 158th Plaza, Omaha, NE 68130. Active ingredient: Bifenthrin. Proposed uses: Dogs... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OPP-2010-0008; FRL-8843-5] Pesticide Products... announces receipt of applications to register new uses for pesticide products containing currently...

  19. Atmospheric Concentrations of Organochlorine Pesticides in the ...

    African Journals Online (AJOL)

    Organochlorine pesticides may still be in use in the Eastern African region for agricultural purposes and for the control of mosquitoes. Atmospheric concentrations of organochlorine pesticides are expected to be higher in the tropics compared to temperate regions due to prevailing high temperatures. However, no study has ...

  20. EPA Regulation of Bed Bug Pesticides

    Science.gov (United States)

    All pesticides must be registered by EPA before being sold and used in the U.S., other than those that rely on a limited set of active ingredients (so-called minimum risk pesticides). EPA reviews for safety and effectiveness.

  1. Chlorinated pesticide residues in marine sediments

    Digital Repository Service at National Institute of Oceanography (India)

    Sarkar, A.; SenGupta, R.

    of pesticide in contaminated river water into the Bay of Bengal. Con centration ranges of all these pesticide residues detected were, aldrine: 0.02-0.53, gamma BHC: 0.01-0.21, dieldrine: 0.05-0.51, and total DDT: 0.02-0.78, all in mu g g sup(-1) (wet wt)....

  2. Pesticide biotransformation and fate in heterogeneous environments

    NARCIS (Netherlands)

    Vink, J.P.M.

    1997-01-01

    The effects and relative impacts of environmental variables on the behaviour of pesticides, through the effect on pesticide-degrading microorganisms, was studied in a broad spectrum and covered the most relevant emission routes. It is shown that the effect of landscape geochemistry, which

  3. QA/QC in pesticide residue analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ambrus, A [Agrochemicals Unit, Agency' s Laboratories, Seibersdorf (Austria)

    2002-07-01

    This paper outlines problems related to pesticide residue analysis in a regulatory laboratory that are related to: availability of reference materials, as over 1000 pesticide active ingredients are currently in use and over 400 crops represent a large part of a healthy diet; analysis time; availability of samples in sufficient numbers; uncertainties of the procedures.

  4. QA/QC in pesticide residue analysis

    International Nuclear Information System (INIS)

    Ambrus, A.

    2002-01-01

    This paper outlines problems related to pesticide residue analysis in a regulatory laboratory that are related to: availability of reference materials, as over 1000 pesticide active ingredients are currently in use and over 400 crops represent a large part of a healthy diet; analysis time; availability of samples in sufficient numbers; uncertainties of the procedures

  5. Residential exposures to pesticides and childhood leukaemia

    International Nuclear Information System (INIS)

    Metayer, C.; Buffler, P. A.

    2008-01-01

    Like many chemicals, carcinogenicity of pesticides is poorly characterised in humans, especially in children, so that the present knowledge about childhood leukaemia risk derives primarily from epidemiological studies. Overall, case-control studies published in the last decade have reported positive associations with home use of insecticides, mostly before the child's birth, while findings for herbicides are mixed. Previous studies relied solely on self-reports, therefore lacking information on active ingredients and effects of potential recall bias. Few series to date have examined the influence of children's genetic susceptibility related to transport and metabolism of pesticides. To overcome these limitations, investigators of the Northern California Childhood Leukaemia Study (NCCLS) have undertaken, in collaboration with a multidisciplinary team, a comprehensive assessment of residential pesticide exposure, including: (1) quality control of self-reports; (2) home pesticide inventory and linkage to the Environmental Protection Agency to obtain data on active ingredients; (3) collection and laboratory analyses of ∼600 home dust samples for over 60 pesticides and (4) geographic information studies using California environmental databases to assess exposure to agricultural pesticides. The NCCLS is also conducting large-scale geno-typing to evaluate the role of genes in xenobiotic pathways relevant to the transport and metabolism of pesticides. A better quantification of children's exposures to pesticides at home is critical to the evaluation of childhood leukaemia risk, especially for future gene-environment interaction studies. (authors)

  6. PESTICIDE CONTAMINATION OF THE DRIDJI COTTON ...

    African Journals Online (AJOL)

    ruud

    pesticide contamination in the Dridji cotton production area poses a risk to public ... the Kiti River as well as bean leaves grown near the river were sampled and ... Sediments were analysed at the Institute of Environmental Studies of the VU .... Empty bottles of pesticides were recycled to buy oil from the market and to bring.

  7. INDOOR THERMAL CONDITION OF FACTORY BUILDING IN BANGLADESH

    Directory of Open Access Journals (Sweden)

    Muhammed Abdullah Al Sayem Khan

    2011-12-01

    Full Text Available Bangladesh is a developing country and has a lot of factories for different products for local use and also export to abroad. Garments industries are one of the top most items of exported items. A huge number of populations are working in garments industries. But these factories are not well designed in sense of the thermal environment. Workers experiences sickness related to indoor environment. The productions of these factories are affected due to employees’ health condition. The research is done in two different methods. One is empirical data collection using thermal data loggers and the other is questionnaire survey on the spots for three factory buildings. The field study was conducted in four different months of the same year during winter and summer period. Expected findings of this research are that the indoor environment is not comfortable for works at day time during summer season. This research will help the factory workers in providing a comfortable thermal environment and also help the employers or factory owners to increase their production margin.

  8. Implementing Clinical Research Using Factorial Designs: A Primer.

    Science.gov (United States)

    Baker, Timothy B; Smith, Stevens S; Bolt, Daniel M; Loh, Wei-Yin; Mermelstein, Robin; Fiore, Michael C; Piper, Megan E; Collins, Linda M

    2017-07-01

    Factorial experiments have rarely been used in the development or evaluation of clinical interventions. However, factorial designs offer advantages over randomized controlled trial designs, the latter being much more frequently used in such research. Factorial designs are highly efficient (permitting evaluation of multiple intervention components with good statistical power) and present the opportunity to detect interactions amongst intervention components. Such advantages have led methodologists to advocate for the greater use of factorial designs in research on clinical interventions (Collins, Dziak, & Li, 2009). However, researchers considering the use of such designs in clinical research face a series of choices that have consequential implications for the interpretability and value of the experimental results. These choices include: whether to use a factorial design, selection of the number and type of factors to include, how to address the compatibility of the different factors included, whether and how to avoid confounds between the type and number of interventions a participant receives, and how to interpret interactions. The use of factorial designs in clinical intervention research poses choices that differ from those typically considered in randomized clinical trial designs. However, the great information yield of the former encourages clinical researchers' increased and careful execution of such designs. Copyright © 2017. Published by Elsevier Ltd.

  9. Black hole as a wormhole factory

    Directory of Open Access Journals (Sweden)

    Sung-Won Kim

    2015-12-01

    Full Text Available There have been lots of debates about the final fate of an evaporating black hole and the singularity hidden by an event horizon in quantum gravity. However, on general grounds, one may argue that a black hole stops radiation at the Planck mass (ħc/G1/2∼10−5 g, where the radiated energy is comparable to the black hole's mass. And also, it has been argued that there would be a wormhole-like structure, known as “spacetime foam”, due to large fluctuations below the Planck length (ħG/c31/2∼10−33 cm. In this paper, as an explicit example, we consider an exact classical solution which represents nicely those two properties in a recently proposed quantum gravity model based on different scaling dimensions between space and time coordinates. The solution, called “Black Wormhole”, consists of two different states, depending on its mass parameter M and an IR parameter ω: For the black hole state (with ωM2>1/2, a non-traversable wormhole occupies the interior region of the black hole around the singularity at the origin, whereas for the wormhole state (with ωM2<1/2, the interior wormhole is exposed to an outside observer as the black hole horizon is disappearing from evaporation. The black hole state becomes thermodynamically stable as it approaches the merging point where the interior wormhole throat and the black hole horizon merges, and the Hawking temperature vanishes at the exact merge point (with ωM2=1/2. This solution suggests the “Generalized Cosmic Censorship” by the existence of a wormhole-like structure which protects the naked singularity even after the black hole evaporation. One could understand the would-be wormhole inside the black hole horizon as the result of microscopic wormholes created by “negative” energy quanta which have entered the black hole horizon in Hawking radiation process; the quantum black hole could be a wormhole factory! It is found that this speculative picture may be consistent with the

  10. Predictive acute toxicity tests with pesticides.

    Science.gov (United States)

    Brown, V K

    1983-01-01

    By definition pesticides are biocidal products and this implies a probability that pesticides may be acutely toxic to species other than the designated target species. The ways in which pesticides are manufactured, formulated, packaged, distributed and used necessitates a potential for the exposure of non-target species although the technology exists to minimize adventitious exposure. The occurrence of deliberate exposure of non-target species due to the misuse of pesticides is known to happen. The array of predictive acute toxicity tests carried out on pesticides and involving the use of laboratory animals can be justified as providing data on which hazard assessment can be based. This paper addresses the justification and rationale of this statement.

  11. Measurement of Air Pollution Comes from Adra Cement Factory

    International Nuclear Information System (INIS)

    Odat, M.; Meslmani, Y.; Al-Kharfan, K.; Shamali, K.

    2013-06-01

    Measurements of air pollution were carried out in and around Adra cement factory during a single period (December). The Measurements included the following: 1- Dust fall. 2- Total suspended particulates (TSP) and inhalable particulates PM-1-0 & PM-3 inside the factor and in residential area surrounded the factory (Worker City of Adra, Adra city, Wafeden Mokheam, Baironi Hospital and Alkatiefa City). 3-Determination the levels of Cd, Pb, Cu and zinc associated with air born. 4- Determination of toxic gases (CO, SO-2 and NO-x) emitted from the chimneys. The results showed that the quantity of dust fall was varied obviously inside the factory and the regions affected by air pollutions. The monthly concentration of dust fall were 165, 27 and 10 tons/Km 2 /month inside the factory , affected villages and Baironi Hospital respectively, Wherein the permissible limit is (9tons/Km'2/month). The total suspended particulates (TSP) and inhalable particulates PM-1-0 & PM-3 in the studies area were higher than the permissible limit. The TSP concentrations inside the factory ranged between 497 and 2021 microgram/m'3 while the ranged between 328 and 561 microgram /m'3 in the surrounded villages and between 232 and 244 microgram/m'3 near Damascus, the were far higher than the world health organization (WHO) standards (120 Microgram/m'3). The PM-3 which is the most effecting on the human health reached 117.6, 124.6 and 62.6 microgram /m 3 inside the factory (main in trance), city worker of Adra and Baironi Hospital respectively, theses concentrations were higher than the Syrian standards (15 microgram/m'3) The measurements which were carried out through an exclusive day refered that the percentage of TSP/PM-3 is increasedwith moving away from the factory and reached 6.8, 18.6, 19.3% in the main intrance of the factory, worker city of Adra and Bironi Hospital respectively. The level of toxic gases inside the source (chimneys) was within the standards

  12. Direct immersion single drop micro-extraction method for multi-class pesticides analysis in mango using GC-MS.

    Science.gov (United States)

    Pano-Farias, Norma S; Ceballos-Magaña, Silvia G; Muñiz-Valencia, Roberto; Jurado, Jose M; Alcázar, Ángela; Aguayo-Villarreal, Ismael A

    2017-12-15

    Due the negative effects of pesticides on environment and human health, more efficient and environmentally friendly methods are needed. In this sense, a simple, fast, free from memory effects and economical direct-immersion single drop micro-extraction (SDME) method and GC-MS for multi-class pesticides determination in mango samples was developed. Sample pre-treatment using ultrasound-assisted solvent extraction and factors affecting the SDME procedure (extractant solvent, drop volume, stirring rate, ionic strength, time, pH and temperature) were optimized using factorial experimental design. This method presented high sensitive (LOD: 0.14-169.20μgkg -1 ), acceptable precision (RSD: 0.7-19.1%), satisfactory recovery (69-119%) and high enrichment factors (20-722). Several obtained LOQs are below the MRLs established by the European Commission; therefore, the method could be applied for pesticides determination in routing analysis and custom laboratories. Moreover, this method has shown to be suitable for determination of some of the studied pesticides in lime, melon, papaya, banana, tomato, and lettuce. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Pesticide Toxicity Index: a tool for assessing potential toxicity of pesticide mixtures to freshwater aquatic organisms

    Science.gov (United States)

    Nowell, Lisa H.; Norman, Julia E.; Moran, Patrick W.; Martin, Jeffrey D.; Stone, Wesley W.

    2014-01-01

    Pesticide mixtures are common in streams with agricultural or urban influence in the watershed. The Pesticide Toxicity Index (PTI) is a screening tool to assess potential aquatic toxicity of complex pesticide mixtures by combining measures of pesticide exposure and acute toxicity in an additive toxic-unit model. The PTI is determined separately for fish, cladocerans, and benthic invertebrates. This study expands the number of pesticides and degradates included in previous editions of the PTI from 124 to 492 pesticides and degradates, and includes two types of PTI for use in different applications, depending on study objectives. The Median-PTI was calculated from median toxicity values for individual pesticides, so is robust to outliers and is appropriate for comparing relative potential toxicity among samples, sites, or pesticides. The Sensitive-PTI uses the 5th percentile of available toxicity values, so is a more sensitive screening-level indicator of potential toxicity. PTI predictions of toxicity in environmental samples were tested using data aggregated from published field studies that measured pesticide concentrations and toxicity to Ceriodaphnia dubia in ambient stream water. C. dubia survival was reduced to ≤ 50% of controls in 44% of samples with Median-PTI values of 0.1–1, and to 0% in 96% of samples with Median-PTI values > 1. The PTI is a relative, but quantitative, indicator of potential toxicity that can be used to evaluate relationships between pesticide exposure and biological condition.

  14. Utilization of Boxes for Pesticide Storage in Sri Lanka

    DEFF Research Database (Denmark)

    Pieris, Ravi; Weerasinghe, Manjula; Abeywickrama, Tharaka

    2017-01-01

    Pesticide self-poisoning is now considered one of the two most common methods of suicide worldwide. Encouraging safe storage of pesticides is one particular approach aimed at reducing pesticide self-poisoning. CropLife Sri Lanka (the local association of pesticide manufacturers), with the aid of ...

  15. 33 CFR 274.7 - Authorization of pesticide use.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Authorization of pesticide use... of pesticide use. (a) Programs approved in § 274.6(b) must be those as described on the pesticide label. Pesticide uses which are different from the registered use, require amendment of the label...

  16. Spreading the Word about Pesticide Hazards and Alternatives.

    Science.gov (United States)

    Grier, Norma

    1993-01-01

    Presents a pamphlet and four brochures about pesticide hazards, pesticide use and alternatives, special impacts on children, lawn and garden pest management, and pesticides in food. Discusses the whys and ways of using these materials to inform people about pesticide issues. (MDH)

  17. Simulating Effects of Forest Management Practices on Pesticide.

    Science.gov (United States)

    M.C. Smith; W.G. Knisel; J.L. Michael; D.G. Neary

    1993-01-01

    The GLEAMS model pesticide component was modified to simulate up to 245 pesticides simultaneously, and the revised model was used to pesticide pesticide application windows for forest site preparation and pine release. Five herbicides were made for soils representing four hydrologic soil groups in four climatic regions of the southeastern United States. Five herbicides...

  18. Apply Pesticides Correctly: A Guide for Commercial Applicators.

    Science.gov (United States)

    Environmental Protection Agency, Washington, DC.

    This document provides practical information needed by commercial pesticide applicators to meet the minimum Federal regulation requirements for the use of various pesticides. The text and accompanying illustrations cover the seven major topics of pests, pest control, pesticides, labels and labeling, using pesticides safely, application equipment,…

  19. 40 CFR 273.3 - Applicability-pesticides.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Applicability-pesticides. 273.3... (CONTINUED) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT General § 273.3 Applicability—pesticides. (a) Pesticides covered under this part 273. The requirements of this part apply to persons managing pesticides, as...

  20. [Ecotoxicological study of chlorinated pesticides].

    Science.gov (United States)

    Rosival, L; Szokolay, A; Uhnák, J

    1980-01-01

    The authors describe a model for the ecotoxicological investigation of pesticide residues guided by the analysis of various links of the food chain and of human materials. It is pointed to the possibility of studying the dynamics of the exposure to human beings by analyzing gynaecological material (prenatal stage) and samples obtained at necropsy from human beings of varying age (different durations of exposure). The observations of the relative accumulation of hexachlorobenzene, beta-BHC and DDT in butter, human milk and human fat in a region with intensive cultivation revealed a considerble accumulation of hexachlorobenzene which reaches the level of DDT. The conclusion drawn from ecotoxicological studies indicates that a reduction of the tolerances of pesticide residues in raw materials for baby foods is imperative. The analyses of gynaecological material (202 samples of the available content of the uterus and 24 placental and embryonic specimens) permitted to evidence a significant difference between two regions and a specific relationship of the observed substances and their metabolites to the fat-dissolving power of the analyzed materials.

  1. DEVELOPMENT OF LAW RELATING TO FACTORIES IN INDIA

    Directory of Open Access Journals (Sweden)

    M. K. Sahu

    2015-01-01

    Full Text Available The rapid growth of industrial town and factories has paved the way to develop our industrial legislation accordingly. The Government of India never expressed their interest in framing separate legislation vis-à-vis factories which resulted in implementation of the same statute which was enacted pre-independence. It was done by virtue of Art. 372 of the Constitution of India. However, the Constitutional Lawmakers created vacuum for the implementation of new statute in accordance with the demand of society by inserting scope under the Directive Principles of State Policies. However, in the 67 years history of Indian Republic, there are unprecedented developments of law relating to factories in India.The Government of India, with the adoption of existed statute, made an effort to incorporate the welfare legislation but it never developed along with the change in time. It is to be noticed that as far as existing statutes are concerned, the development is an effect of judicial pronouncement or some tragic incident like Bhopal Gas Tragedy. This paper succinctly describes the history of factory legislation, the constitutional validity of the previous statute and necessary amendment which have already been done and / or on the verge of being amended. It will further discuss contribution of judiciary in developing the law relating to factories, scope of industrial jurisprudence in promoting the development of factory legislation. The primary focus of the research project is to reflect upon the areas where factory legislation has developed, so that proper yardstick could be made in order to put emphasis on those areas which have been remained untouched.

  2. Design, analysis and presentation of factorial randomised controlled trials

    Directory of Open Access Journals (Sweden)

    Little Paul

    2003-11-01

    Full Text Available Abstract Background The evaluation of more than one intervention in the same randomised controlled trial can be achieved using a parallel group design. However this requires increased sample size and can be inefficient, especially if there is also interest in considering combinations of the interventions. An alternative may be a factorial trial, where for two interventions participants are allocated to receive neither intervention, one or the other, or both. Factorial trials require special considerations, however, particularly at the design and analysis stages. Discussion Using a 2 × 2 factorial trial as an example, we present a number of issues that should be considered when planning a factorial trial. The main design issue is that of sample size. Factorial trials are most often powered to detect the main effects of interventions, since adequate power to detect plausible interactions requires greatly increased sample sizes. The main analytical issues relate to the investigation of main effects and the interaction between the interventions in appropriate regression models. Presentation of results should reflect the analytical strategy with an emphasis on the principal research questions. We also give an example of how baseline and follow-up data should be presented. Lastly, we discuss the implications of the design, analytical and presentational issues covered. Summary Difficulties in interpreting the results of factorial trials if an influential interaction is observed is the cost of the potential for efficient, simultaneous consideration of two or more interventions. Factorial trials can in principle be designed to have adequate power to detect realistic interactions, and in any case they are the only design that allows such effects to be investigated.

  3. Pesticides in Brazilian freshwaters: a critical review.

    Science.gov (United States)

    Albuquerque, A F; Ribeiro, J S; Kummrow, F; Nogueira, A J A; Montagner, C C; Umbuzeiro, G A

    2016-07-13

    The widespread use of pesticides in agriculture can lead to water contamination and cause adverse effects on non-target organisms. Brazil has been the world's top pesticide market consumer since 2008, with 381 approved pesticides for crop use. This study provides a comprehensive literature review on the occurrence of pesticide residues in Brazilian freshwaters. We searched for information in official agency records and peer-reviewed scientific literature. Risk quotients were calculated to assess the potential risk posed to aquatic life by the individual pesticides based on their levels of water contamination. Studies about the occurrence of pesticides in freshwaters in Brazil are scarce and concentrated in few sampling sites in 5 of the 27 states. Herbicides (21) accounted for the majority of the substances investigated, followed by fungicides (11), insecticides (10) and plant growth regulators (1). Insecticides are the class of major concern. Brazil would benefit from the implementation of a nationwide pesticide freshwater monitoring program to support preventive, remediation and enforcement actions.

  4. Characterizing pesticide dissipation in food crops

    DEFF Research Database (Denmark)

    Fantke, Peter; Juraske, R.; Jolliet, O.

    2013-01-01

    Ingestion of residues via consumption of food crops is the predominant exposure route of the general population toward pesticides. However, pesticide dissipation in crops constitutes a main source of uncertainty in estimating residues in harvested crop parts and subsequent human exposure. Neverth......Ingestion of residues via consumption of food crops is the predominant exposure route of the general population toward pesticides. However, pesticide dissipation in crops constitutes a main source of uncertainty in estimating residues in harvested crop parts and subsequent human exposure....... Nevertheless, dissipation is a key mechanism in models assessing pesticide distribution in the cropenvironment and the magnitude of residues in harvest. We provide a consistent framework for characterizing pesticide dissipation in food crops for use in modeling approaches applied in health risk and impact...... degradation is dominating. We are currently testing the regression to predict degradation half-lives in crops. By providing mean degradation half-lives at 20°C for more than 300 pesticides, we reduce uncertainty and improve assumptions in current practice of health risk and impact assessments....

  5. 78 FR 36778 - Pesticide Program Dialogue Committee; Notice of Public Meeting

    Science.gov (United States)

    2013-06-19

    ... associations; environmental, consumer, and farm worker groups; pesticide users and growers; animal rights... animal rights groups; farm worker organizations; pesticide industry and trade associations; pesticide...

  6. Incense and Joss Stick Making in Small Household Factories, Thailand

    Directory of Open Access Journals (Sweden)

    S Siripanich

    2014-07-01

    Full Text Available Background: Incense and joss stick are generally used in the world. Most products were made in small household factories. There are many environmental and occupational hazards in these factories. Objective: To evaluate the workplace environmental and occupational hazards in small household incense and joss stick factories in Roi-Et, Thailand. Methods: Nine small household factories in rural areas of Roi-Et, Thailand, were studied. Dust concentration and small aerosol particles were counted through real time exposure monitoring. The inductively coupled plasma optical emission spectrometry (ICP-OES was used for quantitative measurement of heavy metal residue in incense products. Results: Several heavy metals were found in dissolved dye and joss sticks. Those included barium, manganese, and lead. Rolling and shaking processes produced the highest concentration of dust and aerosols. Only 3.9 % of female workers used personal protection equipment. Conclusion: Dust and chemicals were major threats in small household incense and joss stick factories in Thailand. Increasing awareness towards using personal protection equipment and emphasis on elimination of environmental workplace hazards should be considered to help the workers of this industry.

  7. SYSTEMS BIOLOGY AND METABOLIC ENGINEERING OF ARTHROSPIRA CELL FACTORIES

    Directory of Open Access Journals (Sweden)

    Amornpan Klanchui

    2012-10-01

    Full Text Available Arthrospira are attractive candidates to serve as cell factories for production of many valuable compounds useful for food, feed, fuel and pharmaceutical industries. In connection with the development of sustainable bioprocessing, it is a challenge to design and develop efficient Arthrospira cell factories which can certify effective conversion from the raw materials (i.e. CO2 and sun light into desired products. With the current availability of the genome sequences and metabolic models of Arthrospira, the development of Arthrospira factories can now be accelerated by means of systems biology and the metabolic engineering approach. Here, we review recent research involving the use of Arthrospira cell factories for industrial applications, as well as the exploitation of systems biology and the metabolic engineering approach for studying Arthrospira. The current status of genomics and proteomics through the development of the genome-scale metabolic model of Arthrospira, as well as the use of mathematical modeling to simulate the phenotypes resulting from the different metabolic engineering strategies are discussed. At the end, the perspective and future direction on Arthrospira cell factories for industrial biotechnology are presented.

  8. Operating a production pilot factory serving several scientific domains

    Science.gov (United States)

    Sfiligoi, I.; Würthwein, F.; Andrews, W.; Dost, J. M.; MacNeill, I.; McCrea, A.; Sheripon, E.; Murphy, C. W.

    2011-12-01

    Pilot infrastructures are becoming prominent players in the Grid environment. One of the major advantages is represented by the reduced effort required by the user communities (also known as Virtual Organizations or VOs) due to the outsourcing of the Grid interfacing services, i.e. the pilot factory, to Grid experts. One such pilot factory, based on the glideinWMS pilot infrastructure, is being operated by the Open Science Grid at University of California San Diego (UCSD). This pilot factory is serving multiple VOs from several scientific domains. Currently the three major clients are the analysis operations of the HEP experiment CMS, the community VO HCC, which serves mostly math, biology and computer science users, and the structural biology VO NEBioGrid. The UCSD glidein factory allows the served VOs to use Grid resources distributed over 150 sites in North and South America, in Europe, and in Asia. This paper presents the steps taken to create a production quality pilot factory, together with the challenges encountered along the road.

  9. Operating a production pilot factory serving several scientific domains

    International Nuclear Information System (INIS)

    Sfiligoi, I; Würthwein, F; Andrews, W; Dost, J M; MacNeill, I; McCrea, A; Sheripon, E; Murphy, C W

    2011-01-01

    Pilot infrastructures are becoming prominent players in the Grid environment. One of the major advantages is represented by the reduced effort required by the user communities (also known as Virtual Organizations or VOs) due to the outsourcing of the Grid interfacing services, i.e. the pilot factory, to Grid experts. One such pilot factory, based on the glideinWMS pilot infrastructure, is being operated by the Open Science Grid at University of California San Diego (UCSD). This pilot factory is serving multiple VOs from several scientific domains. Currently the three major clients are the analysis operations of the HEP experiment CMS, the community VO HCC, which serves mostly math, biology and computer science users, and the structural biology VO NEBioGrid. The UCSD glidein factory allows the served VOs to use Grid resources distributed over 150 sites in North and South America, in Europe, and in Asia. This paper presents the steps taken to create a production quality pilot factory, together with the challenges encountered along the road.

  10. Status of pesticides pollution in Tanzania - A review.

    Science.gov (United States)

    Elibariki, Raheli; Maguta, Mihayo Musabila

    2017-07-01

    Various studies have been conducted in Tanzania to assess the magnitude of pesticides pollution associated with pesticides application, storage, disposal as well as knowledge of farmers on pesticides handling. The studies analysed samples from different matrices covering vegetation, biota, water, sediments and soil. The objective of this review was to summarise the results of pesticides residues reported in different components of the environment to give a clear picture of pesticides pollution status in the country for law enforcement as well as for taking precaution measures. Gaps which need to be filled in order to establish a comprehensive understanding on pesticides pollution in the country have also been highlighted. Reviewed studies revealed that, most of the samples contained pesticides below permissible limits (WHO, FAO, US-EPA) except for few samples such as water from Kikavu river, Kilimanjaro region and Kilolo district, Iringa region which were detected with some Organochlorine pesticides (OCPs) above WHO permissible limits. Some soil samples from the former storage sites also contained pesticides above FAO permissible limits. Pesticides and their metabolites were also detected both in vegetation, food and biota samples. The prevalent pesticides in the reviewed studies were the organochlorines such as Dichlorodiphenyltrichloroethane (DDT), endosulfan and Hexachlorocyclohexane (HCH). Surveys to assess farmer's knowledge on pesticides handling observed poor understanding of farmers on pesticides storage, application and disposal. Decontamination of former storage areas, continuous monitoring of pesticide applications and training of farmers on proper handling of pesticides are highly recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. The Pesticide Risk Beliefs Inventory: A Quantitative Instrument for the Assessment of Beliefs about Pesticide Risks

    OpenAIRE

    LePrevost, Catherine E.; Blanchard, Margaret R.; Cope, W. Gregory

    2011-01-01

    Recent media attention has focused on the risks that agricultural pesticides pose to the environment and human health; thus, these topics provide focal areas for scientists and science educators to enhance public understanding of basic toxicology concepts. This study details the development of a quantitative inventory to gauge pesticide risk beliefs. The goal of the inventory was to characterize misconceptions and knowledge gaps, as well as expert-like beliefs, concerning pesticide risk. This...

  12. Pesticide Environmental Accounting: A method for assessing the external costs of individual pesticide applications

    International Nuclear Information System (INIS)

    Leach, A.W.; Mumford, J.D.

    2008-01-01

    The Pesticide Environmental Accounting (PEA) tool provides a monetary estimate of environmental and health impacts per hectare-application for any pesticide. The model combines the Environmental Impact Quotient method and a methodology for absolute estimates of external pesticide costs in UK, USA and Germany. For many countries resources are not available for intensive assessments of external pesticide costs. The model converts external costs of a pesticide in the UK, USA and Germany to Mediterranean countries. Economic and policy applications include estimating impacts of pesticide reduction policies or benefits from technologies replacing pesticides, such as sterile insect technique. The system integrates disparate data and approaches into a single logical method. The assumptions in the system provide transparency and consistency but at the cost of some specificity and precision, a reasonable trade-off for a method that provides both comparative estimates of pesticide impacts and area-based assessments of absolute impacts. - A method to estimate the external costs of a pesticide application based on the ecotoxicology, environmental behaviour and application rate of an active ingredient

  13. Pesticides

    Science.gov (United States)

    ... with Scientists Press Events & Ceremonies Science & Training Videos Scientific Seminars News & Events Find out about the exciting discoveries being made by NIEHS and NIEHS-supported researchers ...

  14. Pesticides

    Science.gov (United States)

    ... Board Review Course ACMT at NACCT Seminars in Forensic Toxicology Annual Scientific Meeting Past ACMT Courses Chemical Agents ... Training Research Webinar Other Enduring Education Seminar in Forensic Toxicology Webinar PEHSU National Classroom Toxicology Visual Pearls Chemical ...

  15. ASME factory authorization system and the situation in Japan

    International Nuclear Information System (INIS)

    Futagawa, Kiyoshi

    1978-01-01

    Since about three or four years ago, the enterprises of machinery, iron and steel and welding materials in Japan are paying much attention to the acquisition of ASME (American Society of Mechanical Engineers) certificates or authorization to stamp the code symbols. That is, over 70 factories in Japan have undergone ASME examination, and consequently acquired the authorization or certificates. Such authorization is divided into over 20 kinds, of which about 7 are possessed by the companies in Japan. In nuclear field, the kinds of authorization are N (nuclear vessel), NPT (nuclear vessel parts), NV (nuclear vessel safety valve), and MM (material manufacturing). In non-nuclear fields, they are S (power boilers), U (pressure vessels, in Div. 1), and U2 (pressure vessels in Div. 2). The following matters are described: ASME setup, authorization procedures of ASME for factories, the kinds of authorization, factories in Japan holding the authorization or certificates, and renewal of the authorization. (Mori, K.)

  16. Synthetic yeast based cell factories for vanillin-glucoside production

    DEFF Research Database (Denmark)

    Strucko, Tomas

    and controlled expression/overexpression of genes of interest. De novo biosynthetic pathway for vanillin-β-glucoside production was employed as a model system for several case studies in this project. In order to construct yeast cell factories fulfilling current demands of industrial biotechnology, methods......The yeast Saccharomyces cerevisiae is well a characterized microorganism and widely used as eukaryotic model organism as well as a key cell factory for bioproduction of various products. The latter comprise a large variety of scientifically and industrially relevant products such as low-value bulk...... chemicals and biofuels, food additives, high-value chemicals and recombinant proteins. Despite the recent achievements in the fields of systems biology and metabolic engineering together with availability of broad genetic engineering toolbox, the full potential of S. cerevisiae as a cell factory is not yet...

  17. Enzyme stabilization for pesticide degradation

    Energy Technology Data Exchange (ETDEWEB)

    Rivers, D.B.; Frazer, F.R. III; Mason, D.W.; Tice, T.R.

    1988-01-01

    Enzymes offer inherent advantages and limitations as active components of formulations used to decontaminate soil and equipment contaminated with toxic materials such as pesticides. Because of the catalytic nature of enzymes, each molecule of enzyme has the potential to destroy countless molecules of a contaminating toxic compound. This degradation takes place under mild environmental conditions of pH, temperature, pressure, and solvent. The basic limitation of enzymes is their degree of stability during storage and application conditions. Stabilizing methods such as the use of additives, covalent crosslinking, covalent attachment, gel entrapment, and microencapsulation have been directed developing an enzyme preparation that is stable under extremes of pH, temperature, and exposure to organic solvents. Initial studies were conducted using the model enzymes subtilisin and horseradish peroxidase.

  18. A survey of warning colours of pesticides.

    Science.gov (United States)

    Thierauf, Annette; Weinmann, Wolfgang; Auwärter, Volker; Vennemann, Benedikt; Bohnert, Michael

    2010-12-01

    Pesticides are used to protect plants all over the world. Their increasing specificity has been due to utilization of differences in biochemical processes, and has been accompanied by lower human toxicity. Nevertheless cases of poisoning are still observed. While certain toxic substances are provided with characteristic dyes or pigments to facilitate easy identification, no overview of pesticide colors exists. The lack of available product information prompted us to explore the colors and dyes of pesticides registered in Germany, most of which are commercially available worldwide. A compilation of the colors and odors of 207 pesticide products is presented. While some of the substances can be identified by their physical characteristics, in other cases, the range of possibilities can be narrowed by their nature and color.

  19. A review: radiolabeled synthesis of pesticides

    International Nuclear Information System (INIS)

    Li Juying; Han Ailiang; Wang Haiyan; Wang Wei; Ye Qingfu

    2010-01-01

    Isotope tracer technique has been widely applied in studies of metabolism, mode action, fate and environmental behavior of pesticides. In such studies, the key point is to obtain suitable radiolabelled compounds. However, the radiotracers, especially the labelled pesticides which are novel compounds with complex structures and longer synthesis routes, are usually unavailable from domestic and /or foreign markets. Therefore, it is essential to explore the synthesis methods of radiolabelled pesticides, which are quite different from the conventional nonradiosynthesis, and are requested to obtain higher yield. This article is a review on current status of choosing the available radionuclide and labelled position, the main synthesis methods and problems in the process of preparing radiolabelled pesticides. (authors)

  20. Pesticide Applicator Certification in Indian Country

    Science.gov (United States)

    This website provides information about the EPA Plan for the Federal Certification of Applicators of Restricted Use Pesticides within Indian Country, including plan requirements, how to become certified, how to register for training, and who is certified.

  1. Assessing Pesticides under the Endangered Species Act

    Science.gov (United States)

    EPA’s pesticide risk assessment and regulatory processes ensure that protections are in place for all populations of non-target species. We have developed risk assessment procedures to determine potential for harm to individuals of a listed species.

  2. Pesticides in Wyoming Groundwater, 2008-10

    Science.gov (United States)

    Eddy-Miller, Cheryl A.; Bartos, Timothy T.; Taylor, Michelle L.

    2013-01-01

    Groundwater samples were collected from 296 wells during 1995-2006 as part of a baseline study of pesticides in Wyoming groundwater. In 2009, a previous report summarized the results of the baseline sampling and the statistical evaluation of the occurrence of pesticides in relation to selected natural and anthropogenic (human-related) characteristics. During 2008-10, the U.S. Geological Survey, in cooperation with the Wyoming Department of Agriculture, resampled a subset (52) of the 296 wells sampled during 1995-2006 baseline study in order to compare detected compounds and respective concentrations between the two sampling periods and to evaluate the detections of new compounds. The 52 wells were distributed similarly to sites used in the 1995-2006 baseline study with respect to geographic area and land use within the geographic area of interest. Because of the use of different types of reporting levels and variability in reporting-level values during both the 1995-2006 baseline study and the 2008-10 resampling study, analytical results received from the laboratory were recensored. Two levels of recensoring were used to compare pesticides—a compound-specific assessment level (CSAL) that differed by compound and a common assessment level (CAL) of 0.07 microgram per liter. The recensoring techniques and values used for both studies, with the exception of the pesticide 2,4-D methyl ester, were the same. Twenty-eight different pesticides were detected in samples from the 52 wells during the 2008-10 resampling study. Pesticide concentrations were compared with several U.S. Environmental Protection Agency drinking-water standards or health advisories for finished (treated) water established under the Safe Drinking Water Act. All detected pesticides were measured at concentrations smaller than U.S. Environmental Protection Agency drinking-water standards or health advisories where applicable (many pesticides did not have standards or advisories). One or more pesticides

  3. Neonatal outcome following exposure to organophosphorous pesticides

    Directory of Open Access Journals (Sweden)

    Đorđević M.

    2010-01-01

    Full Text Available The aim of our study was to determine the neonatal outcome in mothers and children exposed to organophosphorous pesticides (OP. We found that 22.4% pregnant women were exposed to organophosphorous pesticides. OP pesticide concentration was higher in breast milk, newborn sera than maternal sera. Newborn parameters such as birth weight, birth length, head circumference, Apgar score and presence of meconium, as well as gestational age of delivery, showed no significant difference between the two groups. However, postpartum weight loss, hospitalization duration, levels of newborn bilirubin and glycaemia differed significantly between the two groups. Morbidity and presence of CNS disorders were six times and more than twelve times higher, respectively, in the OP-exposed than in the OP pesticide non-exposed group.

  4. Chiral Pesticide Pharmacokinetics: A Range of Values

    Science.gov (United States)

    Approximately 30% of pesticides are chiral and used as mixtures of two or more stereoisomers. In biological systems, these stereoisomers can exhibit significantly different pharmacokinetics (absorption, distribution, metabolism, and elimination). In spite of these differences, th...

  5. Pesticide Information Sources in the United States.

    Science.gov (United States)

    Alston, Patricia Gayle

    1992-01-01

    Presents an overview of electronic and published sources on pesticides. Includes sources such as databases, CD-ROMs, books, journals, brochures, pamphlets, fact sheets, hotlines, courses, electronic mail, and electronic bulletin boards. (MCO)

  6. Cooperative Agreement on Pesticide Safety Education

    Science.gov (United States)

    EPA is awarding the eXtension Foundation with a cooperative agreement to establish a system to distribute EPA funds to Pesticide Safety Education Programs (PSEPs) in State Cooperative Extension Services at Land Grant Universities.

  7. 78 FR 24094 - Azoxystrobin; Pesticide Tolerances

    Science.gov (United States)

    2013-04-24

    ... Statistics Service (USDA/NASS), proprietary market surveys, and the National Pesticide Use Database for the... 1 to the table in paragraph (a)(1); and 0 e. Revise the introductory text of paragraph (a)(2) The...

  8. Mobile Application for Pesticide Label Matching

    Science.gov (United States)

    The label matching application will give inspectors the ability to instantly compare pesticide product labels against state and federal label databases via their cell phone, tablet or other mobile device.

  9. Find a Bed Bug Pesticide Product

    Science.gov (United States)

    Introduces the Bed Bug Product Search Tool, to help consumers find EPA-registered pesticides for bed bug infestation control. Inclusion in this database is not an endorsement. Always follow label directions carefully.

  10. Anticholinesterase pesticides: metabolism, neurotoxicity, and epidemiology

    National Research Council Canada - National Science Library

    Satoh, Tetsuo, Ph. D; Gupta, Ramesh C

    2010-01-01

    .... The early portion of the book deals with metabolism, mechanisms and biomonitoring of anticholinesterase pesticides, while the later part deals with epidemiological studies, regulatory issues, and therapeutic intervention"--Provided by publisher.

  11. Organophosphorus pesticide poisoning : cases and developments

    NARCIS (Netherlands)

    Aardema, H.; Ligtenberg, J. J. M.; Peters-Polman, O. M.; Tulleken, J. E.; Zijlstra, J. G.; Meertens, John H. J. M.

    Self-poisoning with organophosphate pesticides is a major health problem world-wide. Through the inhibition of acetylcholinesterase, organophosphorus poisoning is characterised by the clinical picture of acute cholinergic crisis. Other manifestations are the intermediate neurotoxic syndrome and

  12. Occurrence of organochlorine and organophosphorus pesticide ...

    African Journals Online (AJOL)

    ADOWIE PERE

    Most of the concentrations were above the maximum residue limits ... (accuracy), precision tests and detection limits. ... times higher than the noise level. ..... Exposure to highly hazardous pesticides: A major public health concern, WHO ...

  13. Endangered Species Litigation and Associated Pesticide Limitations

    Science.gov (United States)

    EPA has been subject to several citizen suits. As a result we have conducted scientific assessments and made effects determinations for various pesticide products as related to specific species of concern.

  14. Genetic Alterations in Pesticide Exposed Bolivian Farmers

    DEFF Research Database (Denmark)

    Jørs, Erik; González, Ana Rosa; Ascarrunz, Maria Eugenia

    2007-01-01

    : Questionnaires were applied and blood tests taken from 81 volunteers from La Paz County, of whom 48 were pesticide exposed farmers and 33 non-exposed controls. Sixty males and 21 females participated with a mean age of 37.3 years (range 17-76). Data of exposure and possible genetic damage were collected...... and evaluated by well known statistical methods, controlling for relevant confounders. To measure genetic damage chromosomal aberrations and the comet assay analysis were performed. Results: Pesticide exposed farmers had a higher degree of genetic damage compared to the control group. The number of chromosomal......, probably related to exposure to pesticides. Due to the potentially negative long term health effects of genetic damage on reproduction and the development of cancer, preventive measures are recommended. Effective control with imports and sales, banning of the most toxic pesticides, education...

  15. 76 FR 17644 - Pesticide Product; Registration Application

    Science.gov (United States)

    2011-03-30

    ... telephone number is (703) 305-5805. FOR FURTHER INFORMATION CONTACT: Gina Casciano, Biopesticides and... Environmental protection, Pesticides and pest. Dated: March 18, 2011. Keith A. Matthews, Director, Biopesticides...

  16. Persistent organochlorine pesticide residues in freshwater systems ...

    African Journals Online (AJOL)

    DRINIE

    determined in water and sediment samples of freshwater systems in the Eastern Cape Province of South Africa that ... The organochlorine pesticides (OCPs) in water and sediments ...... Test Methods For Evaluating Solid Waste (3rd edn.) ...

  17. Pesticide leaching in a changing climate

    DEFF Research Database (Denmark)

    Rasmussen, Signe Bonde

    There is a widespread consensus among scientists that the climate will change in the future, and that this change has already begun. These climatic changes will undoubtedly challenge the use of pesticides, which has been proposed to increase in the future. Accordingly, the primary aim of this Ph......D-project was to contribute to the knowledge of how climate change will effect pesticide leaching in the future, which was done by use of mathematical modelling. The agro-ecological model Daisy, was used in all simulations, as well as the 2 model soils: a coarse sand and a subsurface drained sandy loam containing......, resulting in 3000-year long weather series of statistically stationary climate. Effects of pesticide properties (sorption and degradation), pesticide application dates, and soil properties were included. The synthetic weather series produced in relation to objective (II) were used to simulate future changes...

  18. Determination of Pesticide Residues in Cannabis Smoke

    Directory of Open Access Journals (Sweden)

    Nicholas Sullivan

    2013-01-01

    Full Text Available The present study was conducted in order to quantify to what extent cannabis consumers may be exposed to pesticide and other chemical residues through inhaled mainstream cannabis smoke. Three different smoking devices were evaluated in order to provide a generalized data set representative of pesticide exposures possible for medical cannabis users. Three different pesticides, bifenthrin, diazinon, and permethrin, along with the plant growth regulator paclobutrazol, which are readily available to cultivators in commercial products, were investigated in the experiment. Smoke generated from the smoking devices was condensed in tandem chilled gas traps and analyzed with gas chromatography-mass spectrometry (GC-MS. Recoveries of residues were as high as 69.5% depending on the device used and the component investigated, suggesting that the potential of pesticide and chemical residue exposures to cannabis users is substantial and may pose a significant toxicological threat in the absence of adequate regulatory frameworks.

  19. Anticholinesterase pesticides: metabolism, neurotoxicity, and epidemiology

    National Research Council Canada - National Science Library

    Satoh, Tetsuo, Ph. D; Gupta, Ramesh C

    2010-01-01

    ...; and epidemiology of poisonings and fatalities in people from short- and long- term exposures to these pesticides in different occupational settings on a individual country basis as well as on a global basis...

  20. CONTAMINANTS AND REMEDIAL OPTIONS AT PESTICIDE SITES

    Science.gov (United States)

    Many types of soils, sediments, and sludges are contaminated with a wide variety of pesticides. ite-specific characteristics such as volume to be treated, extent of contamination, and applicable cleanup goals differ greatly, and contaminant toxicity, migration pathways, persisten...

  1. A factory concept for processing and manufacturing with lunar material

    Science.gov (United States)

    Driggers, G. W.

    1977-01-01

    A conceptual design for an orbital factory sized to process 1.5 million metric tons per year of raw lunar fines into 0.3 million metric tons of manufacturing materials is presented. A conservative approach involving application of present earth-based technology leads to a design devoid of new inventions. Earth based counterparts to the factory machinery were used to generate subsystem masses and lumped parameters for volume and mass estimates. The results are considered to be conservative since technologies more advanced than those assumed are presently available in many areas. Some attributes of potential space processing technologies applied to material refinement and component manufacture are discussed.

  2. Neutrino Factory and Muon Collider Collaboration R and D Program

    International Nuclear Information System (INIS)

    Zisman, M.S.

    2000-01-01

    The Neutrino Factory and Muon Collider Collaboration (MC) comprises some 140 scientists and engineers located at U.S. National Laboratories and Universities, and at a number of non-U.S. research institutions. In the past year, the MC R and D program has shifted its focus mainly toward the design issues related to the development of a Neutrino Factory based on a muon storage ring. In this paper the status of the various R and D activities is described, and future plans are outlined

  3. R and D Toward a Neutrino Factory and Muon Collider

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2011-01-01

    Significant progress has been made in recent years in R and D towards a neutrino factory and muon collider. The U.S. Muon Accelerator Program (MAP) has been formed recently to expedite the R and D efforts. This paper will review the U.S. MAP R and D programs for a neutrino factory and muon collider. Muon ionization cooling research is the key element of the program. The first muon ionization cooling demonstration experiment, MICE (Muon Ionization Cooling Experiment), is under construction now at RAL (Rutherford Appleton Laboratory) in the UK. The current status of MICE will be described.

  4. Preliminary analysis of a target factory for laser fusion

    International Nuclear Information System (INIS)

    Sherohman, J.W.; Hendricks, C.D.

    1980-01-01

    An analysis of a target factory leading to the determination of production expressions has provided for the basis of a parametric study. Parameters involving the input and output rate of a process system, processing yield factors, and multiple processing steps and production lines have been used to develop an understanding of their dependence on the rate of target injection for laser fusion. Preliminary results have indicated that a parametric study of this type will be important in the selection of processing methods to be used in the final production scheme of a target factory

  5. Jean Piaget: Images of a life and his factory.

    Science.gov (United States)

    Burman, Jeremy Trevelyan

    2012-08-01

    In this article, I use a new book about Jean Piaget to introduce a new historical method: examining "psychological factories." I also discuss some of the ways that "Great Men" are presented in the literature, as well as opportunities for new projects if one approaches the history of the discipline differently and examines the conditions that made that greatness possible. To that end, the article includes many details about Piaget that have never before been discussed in English. Attention is drawn, in particular, to Piaget's collaborators: the hundreds of workers at his factory in Geneva, many of whom were women. (PsycINFO Database Record (c) 2012 APA, all rights reserved).

  6. Profil Konsumen dan Pesaing pada “Factory Bakery”

    OpenAIRE

    Salam, Ramdhan; Rengkung, Leonardus R; Katiandagho, Theodora M; Ngangi, Charles R

    2015-01-01

    The purpose of this study was to describe the profile of competitors and consumers in the Factory Bakery. This research was conducted at the Factory Bakery is located at Pogidon Street, Tuminting, Manado. The collection of data carried out for three months, from June 2015 to Agustus 2015. The primary data in this study were taken two ways to measure the variables of consumers by asking directly to consumers for six days, whereas for measuring competitors by asking directly to the owner of th...

  7. JINR studies for a Tau-Charm Factory

    International Nuclear Information System (INIS)

    Chelkov, G.

    1994-01-01

    This paper touches on work being done a JINR relevant to a proposal for construction of a tau charm factory, and its attendant detector system. A workshop on such a device was held at JINR in 1992, and here the author touches on questions of what one wants to learn about tau particles from such a machine, the charge to the group looking at a detector design for such a facility, the general conclusions of the JINR study, and a status report of work on the JINR Tau Charm Factory project

  8. CONFOUNDING STRUCTURE OF TWO-LEVEL NONREGULAR FACTORIAL DESIGNS

    Institute of Scientific and Technical Information of China (English)

    Ren Junbai

    2012-01-01

    In design theory,the alias structure of regular fractional factorial designs is elegantly described with group theory.However,this approach cannot be applied to nonregular designs directly. For an arbitrary nonregular design,a natural question is how to describe the confounding relations between its effects,is there any inner structure similar to regular designs? The aim of this article is to answer this basic question.Using coefficients of indicator function,confounding structure of nonregular fractional factorial designs is obtained as linear constrains on the values of effects.A method to estimate the sparse significant effects in an arbitrary nonregular design is given through an example.

  9. The role of factorial cumulants in reactor neutron noise theory

    International Nuclear Information System (INIS)

    Colombino, A.; Pacilio, N.; Sena, G.

    1979-01-01

    The physical meaning and the combinatorial implications of the factorial cumulant of a state variable such as the number of neutrons or the number of neutron counts are specified. Features of the presentation are: (1) the fission process is treated in its entirety without the customary binary emission restriction, (b) the introduction of the factorial cumulants helps in reducing the complexity of the mathematical problems, (c) all the solutions can be obtained analytically. Only the ergodic hypothesis for the neutron population evolution is dealt with. (author)

  10. An asymmetric Β-factory based on PEP

    International Nuclear Information System (INIS)

    Oddone, P.

    1989-01-01

    This paper reviews the motivation for building asymmetric B-factories based on storage rings and describes the current LBL/SLAC study to develop such a factory by modifying the PEP storage ring and adding a new low energy (2.5-3 GeV) storage ring. Collisions between the beam of the modified high energy PEP ring and the low energy ring lead to a luminosity of 2 x 10 33 cm- 2 sec - 1 at E cm = Y(4s) with currents of 0.8A in each beam. Further increases in current can lead to luminosities close to 10 34 cm - 2 sec - 1

  11. PowerFactory applications for power system analysis

    CERN Document Server

    Gonzalez-Longatt, Francisco

    2014-01-01

    This book presents a comprehensive set of guidelines and applications of DIgSILENT PowerFactory, an advanced power system simulation software package, for different types of power systems studies. Written by specialists in the field, it combines expertise and years of experience in the use of DIgSILENT PowerFactory with a deep understanding of power systems analysis. These complementary approaches therefore provide a fresh perspective on how to model, simulate and analyse power systems. It presents methodological approaches for modelling of system components, including both classical and non-

  12. Super oxidation and solidification of organic solvents, polycyclic aromatic hydrocarbons and pesticides at an abandoned chemical factory site

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Kevin; Xu, Paul [Suntime Remediation Company, Changzhou, Jiangsu (China); Loo, Walter [Environment and Technology Services, 1323 Horizon Lane, Patterson, CA 95363 (United States)

    2013-07-01

    Large quantities of organic chemical such as VOCs, SVOCs and POPs were found in the soil of land at an abandoned Chemical Plant. Technology of super oxidation was applied to the soil for cleanup. Fenton process was utilized to treat soil contaminated heavily by BHC, benzene, chlorobenzene, dichlorobenzene, hexachlorobenzene, dichloroethane, dichloropropane, trichlorobenzene and dichloroether, etc. Super oxidation was coupled with method of stabilization for this case to enhance the remediation effect, which proved to be successful. Concentration of concerned pollutants was brought down below the national regulation level by approximately 8 folds. To make the treated soil strong and effective layer preventing pollutants breaking through, Iron powder was mixed in the soil, forming PBR (Permeable Barrier Reactor), to lower the risk to human health. The site after enhanced super oxidation above was totally safe to be developed into a residential community and/or commercial area. (authors)

  13. Management of acute organophosphorus pesticide poisoning

    OpenAIRE

    Eddleston, Michael; Buckley, Nick A; Eyer, Peter; Dawson, Andrew H

    2008-01-01

    Summary Organophosphorus pesticide self-poisoning is an important clinical problem in rural regions of the developing world, and kills an estimated 200?000 people every year. Unintentional poisoning kills far fewer people but is a problem in places where highly toxic organophosphorus pesticides are available. Medical management is difficult, with case fatality generally more than 15%. We describe the limited evidence that can guide therapy and the factors that should be considered when design...

  14. Types of pesticides and determination of their residues

    International Nuclear Information System (INIS)

    Kassem, A.R.

    2010-01-01

    The pesticide is any material or component used to protect from pests. Its toxic effect is related to the chemical structure, which can be divided into 3 types : 1- Metal pesticides : Sulphur, cupper, zinc, mercury; 2- Vegetal pesticides : advanced and less toxic to the general health; 3- Synthetic organo pesticides : organo chlorine, organophosphorous, carbamate and pyrethroids. Pesticides in the soil undergo biological dissociation according to their concentration and chemical structure. High concentration of the pesticides in the soil may lead to fertility decrease due to destruction of micro-organisms by the pesticides. Many methods are used to analyze the residues of pesticides in plant or soil : 1- Chromatographic methods : Gas chromatography, gas liquid chromatography and high performance liquid chromatography; 2- Spectroscopy methods : spectrophotometer and mass spectrometer; 3- Isotopic methods : based on tracers technique which is the most sensitive and accurate method and can estimate minor amounts of the pesticides. (author)

  15. Pesticide modelling for a small catchment using SWAT-2000.

    Science.gov (United States)

    Kannan, Narayanan; White, Sue M; Worrall, Fred; Whelan, Mick J

    2006-01-01

    Pesticides in stream flow from the 142 ha Colworth catchment in Bedfordshire, UK were monitored from October 1999 to December 2000. About 47% of the catchment is tile-drained and different pesticides and cropping patterns have recently been evaluated in terms of their effect on nutrient and pesticide losses to the stream. The data from Colworth were used to test soil and water assessment tool (SWAT) 2000 predictions of pesticide concentrations at the catchment outlet. A sound model set-up to carry out pesticide modelling was created by means of hydrological modelling with proper simulation of crop growth and evapotranspiration. The pesticides terbuthylazine, terbutryn, cyanazine and bentazone were modelled. There was close agreement between SWAT-predicted pesticide concentration values and observations. Scenario trials were conducted to explore management options for reducing pesticide loads arriving at the catchment outlet. The results obtained indicate that SWAT can be used as a tool to understand pesticide behavior at the catchment scale.

  16. Increased Frequency of Rheumatoid Arthritis and Allergic Rhinitis among Pesticide Sprayers and Associations with Pesticide Use.

    Science.gov (United States)

    Koureas, Michalis; Rachiotis, George; Tsakalof, Andreas; Hadjichristodoulou, Christos

    2017-08-01

    Objective : The aim of this study was to identify diseases linked with the pesticide sprayer occupation and explore possible associations with exposure history data. Methods : Α cross sectional study was conducted among pesticide sprayers ( n = 80) and the general population ( n = 90) in Thessaly (Greece). Medical history, demographic characteristics and detailed exposure history were recorded by conducting personal interviews. Lifetime exposure indicators were calculated for several pesticide chemical subclasses. Moreover, organophosphate metabolite levels were quantified in urine samples of all participants by using gas chromatography -mass spectrometry (GC-MS). Multinomial analysis was used to determine associations between occupational pesticide exposure and diseases or disorders. Results : In the pesticide sprayers group, significantly higher frequencies for rheumatoid arthritis (RA) and allergic rhinitis were observed compared with the control group ( p = 0.002 and p = 0.024 respectively). Within the pesticide sprayers group, high lifetime pesticide exposure was associated with increased risk for reporting RA (OR: 43.07 95% CI: 3.09-600.67) and allergic rhinitis (OR: 9.72 95% CI: 2.31-40.89), compared with low pesticide exposure. Exposure to organophsphate, guanidine and quinone pesticides were associated with RA while organophosphates, pyrethroids and paraquat were associated with allergic rhinitis. Despite the higher levels of certain pesticide metabolites observed among participants with rheumatoid arthritis, the differences were not statistically significant. One metabolite (diethylthiophosphate) was found to be significantly increased in allergic rhinitis cases ( p = 0.037). Conclusion s : The results from the current study suggest a possible association of occupational pesticide exposure with RA and allergic rhinitis that should be further investigated.

  17. Pesticides in Soil: Effects on Microorganisms

    Directory of Open Access Journals (Sweden)

    Ljiljana Radivojević

    2007-01-01

    Full Text Available Since their discovery to the present day, pesticides have been an inevitable segment of agricultural production and efforts have been made to synthesize compounds that would share a required efficacy along with selectivity, sufficient persistence on the object of protection and favourable toxicological and ecotoxicological characteristics so as to minimize their effect on the environment.When a pesticide gets into soil after application, it takes part in a number of physical, chemical and biological processes that depend not only on the compound itself, but a number of other factors as well, such as: physical, chemical and biological characteristics of soil; climatic factors, equipment used, method of application, method of storage, handling and disposal of waste, site characteristics (proximity of ground and underground waters, biodiversity and sensitivity of the environment. Microorganisms play an important role in pesticide degradation as they are able to utilize the biogenic elements from those compounds, as well as energy for their physiological processes. On the other hand, pesticides are more or less toxic substances that can have adverse effect on populations of microorganisms and prevent their development, reduce their abundance, deplete their taxonomic complexity and create communities with a lower level of diversity and reduced physiological activity.The article discusses complex interactions between pesticides and microorganisms in soil immediately after application and over the ensuing period. Data on changes in the abundance of some systematic and physiological groups of microorganisms, their microbial biomass and enzymatic activity caused under pesticide activity are discussed as indicators of these processes.

  18. Occupational exposure to pesticides and respiratory health

    Directory of Open Access Journals (Sweden)

    Ali Mamane

    2015-06-01

    Full Text Available This article aims to review the available literature regarding the link between occupational exposure to pesticides and respiratory symptoms or diseases. Identification of epidemiological studies was performed using PubMed. 41 articles were included, 36 regarding agricultural workers and five regarding industry workers. Among the 15 cross-sectional studies focusing on respiratory symptoms and agricultural pesticide exposure, 12 found significant associations with chronic cough, wheeze, dyspnoea, breathlessness or chest tightness. All four studies on asthma found a relationship with occupational exposure, as did all three studies on chronic bronchitis. The four studies that performed spirometry reported impaired respiratory function linked to pesticide exposure, suggestive of either obstructive or restrictive syndrome according to the chemical class of pesticide. 12 papers reported results from cohort studies. Three out of nine found a significant relationship with increased risk of wheeze, five out of nine with asthma and three out of three with chronic bronchitis. In workers employed in pesticide production, elevated risks of chronic obstructive pulmonary disease (two studies out of three and impaired respiratory function suggestive of an obstructive syndrome (two studies out of two were reported. In conclusion, this article suggests that occupational exposure to pesticides is associated with an increased risk of respiratory symptoms, asthma and chronic bronchitis, but the causal relationship is still under debate.

  19. Chlorination of organophosphorus pesticides in natural waters

    Energy Technology Data Exchange (ETDEWEB)

    Acero, Juan L. [Departamento de Ingenieria Quimica y Energetica, Universidad de Extremadura, 06071 Badajoz (Spain)], E-mail: jlacero@unex.es; Benitez, F. Javier; Real, Francisco J.; Gonzalez, Manuel [Departamento de Ingenieria Quimica y Energetica, Universidad de Extremadura, 06071 Badajoz (Spain)

    2008-05-01

    Unknown second-order rate constants for the reactions of three organophosphorus pesticides (chlorpyrifos, chlorfenvinfos and diazinon) with chlorine were determined in the present study, and the influence of pH and temperature was established. It was found that an increase in the pH provides a negative effect on the pesticides degradation rates. Apparent second-order rate constants at 20 {sup o}C and pH 7 were determined to be 110.9, 0.004 and 191.6 M{sup -1} s{sup -1} for chlorpyrifos, chlorfenvinfos and diazinon, respectively. A higher reactivity of chlorine with the phosphorothioate group (chlorpyrifos and diazinon) than with the phosphate moiety (chlorfenvinfos) could explain these results. Intrinsic rate constant for the elementary reactions of chlorine species with chlorpyrifos and diazinon were also calculated, leading to the conclusion that the reaction between hypochlorous acid and the pesticide is predominant at neutral pH. The elimination of these pesticides in surface waters was also investigated. A chlorine dose of 2.5 mg L{sup -1} was enough to oxidize chlorpyrifos and diazinon almost completely, with a formation of trihalomethanes below the EU standard for drinking water. However, the removal of chlorfenvinfos was not appreciable. Therefore, chlorination is a feasible option for the removal of organophosphorus pesticides with phosphorothioate group during oxidation and disinfection processes, but not for the elimination of pesticides with phosphate moiety.

  20. Chlorination of organophosphorus pesticides in natural waters

    International Nuclear Information System (INIS)

    Acero, Juan L.; Benitez, F. Javier; Real, Francisco J.; Gonzalez, Manuel

    2008-01-01

    Unknown second-order rate constants for the reactions of three organophosphorus pesticides (chlorpyrifos, chlorfenvinfos and diazinon) with chlorine were determined in the present study, and the influence of pH and temperature was established. It was found that an increase in the pH provides a negative effect on the pesticides degradation rates. Apparent second-order rate constants at 20 o C and pH 7 were determined to be 110.9, 0.004 and 191.6 M -1 s -1 for chlorpyrifos, chlorfenvinfos and diazinon, respectively. A higher reactivity of chlorine with the phosphorothioate group (chlorpyrifos and diazinon) than with the phosphate moiety (chlorfenvinfos) could explain these results. Intrinsic rate constant for the elementary reactions of chlorine species with chlorpyrifos and diazinon were also calculated, leading to the conclusion that the reaction between hypochlorous acid and the pesticide is predominant at neutral pH. The elimination of these pesticides in surface waters was also investigated. A chlorine dose of 2.5 mg L -1 was enough to oxidize chlorpyrifos and diazinon almost completely, with a formation of trihalomethanes below the EU standard for drinking water. However, the removal of chlorfenvinfos was not appreciable. Therefore, chlorination is a feasible option for the removal of organophosphorus pesticides with phosphorothioate group during oxidation and disinfection processes, but not for the elimination of pesticides with phosphate moiety

  1. Effect of pesticides on soil microbial community.

    Science.gov (United States)

    Lo, Chi-Chu

    2010-07-01

    According to guidelines for the approval of pesticides, information about effects of pesticides on soil microorganisms and soil fertility are required, but the relationships of different structures of pesticides on the growth of various groups of soil microorganisms are not easily predicted. Some pesticides stimulate the growth of microorganisms, but other pesticides have depressive effects or no effects on microorganisms. For examples, carbofuran stimulated the population of Azospirillum and other anaerobic nitrogen fixers in flooded and non-flooded soil, but butachlor reduced the population of Azospirillum and aerobic nitrogen fixers in non-flooded soil. Diuron and chlorotoluron showed no difference between treated and nontreated soil, and linuron showed a strong difference. Phosphorus(P)-contains herbicides glyphosate and insecticide methamidophos stimulated soil microbial growth, but other P-containing insecticide fenamiphos was detrimental to nitrification bacteria. Therefore, the following review presents some data of research carried out during the last 20 years. The effects of twenty-one pesticides on the soil microorganisms associated with nutrient and cycling processes are presented in section 1, and the applications of denaturing gradient gel electrophoresis (DGGE) for studying microbial diversity are discussed in section 2.

  2. Environmental exposure to pesticides and respiratory health

    Directory of Open Access Journals (Sweden)

    Ali Mamane

    2015-09-01

    Full Text Available Respiratory effects of environmental exposure to pesticides are debated. Here we aimed to review epidemiological studies published up until 2013, using the PubMed database. 20 studies dealing with respiratory health and non-occupational pesticide exposure were identified, 14 carried out on children and six on adults. In four out of nine studies in children with biological measurements, mothers' dichlorodiphenyldichloroethylene (DDE blood levels during pregnancy were associated with asthma and wheezing in young children. An association was also found between permethrin in indoor air during pregnancy and wheezing in children. A significant association between asthma and DDE measured in children's blood (aged 7–10 years was observed in one study. However, in three studies, no association was found between asthma or respiratory infections in children and pesticide levels in breast milk and/or infant blood. Lastly, in three out of four studies where post-natal pesticide exposure of children was assessed by parental questionnaire an association with respiratory symptoms was found. Results of the fewer studies on pesticide environmental exposure and respiratory health of adults were much less conclusive: indeed, the associations observed were weak and often not significant. In conclusion, further studies are needed to confirm whether there is a respiratory risk associated with environmental exposure to pesticides.

  3. Quantum chemistry in environmental pesticide risk assessment.

    Science.gov (United States)

    Villaverde, Juan J; López-Goti, Carmen; Alcamí, Manuel; Lamsabhi, Al Mokhtar; Alonso-Prados, José L; Sandín-España, Pilar

    2017-11-01

    The scientific community and regulatory bodies worldwide, currently promote the development of non-experimental tests that produce reliable data for pesticide risk assessment. The use of standard quantum chemistry methods could allow the development of tools to perform a first screening of compounds to be considered for the experimental studies, improving the risk assessment. This fact results in a better distribution of resources and in better planning, allowing a more exhaustive study of the pesticides and their metabolic products. The current paper explores the potential of quantum chemistry in modelling toxicity and environmental behaviour of pesticides and their by-products by using electronic descriptors obtained computationally. Quantum chemistry has potential to estimate the physico-chemical properties of pesticides, including certain chemical reaction mechanisms and their degradation pathways, allowing modelling of the environmental behaviour of both pesticides and their by-products. In this sense, theoretical methods can contribute to performing a more focused risk assessment of pesticides used in the market, and may lead to higher quality and safer agricultural products. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  4. Pesticide risk assessment in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Hill, Richard N [Environmental Protection Agency, Washington, DC (United States)

    1992-07-01

    In recognition of potential risks, all pesticides distributed and sold in the United States must fulfil extensive registration requirements for the Environmental Protection Agency (EPA). Registration is a licensing procedure where industry must submit data to demonstrate the safety of pesticidal substances and products before they can be used commercially. The regulatory control of pesticides is unique among chemicals in the U.S. in that testing beyond initial registration may be imposed by the Agency throughout the commercial life of the chemical, as long as there is adequate justification. Registration requirements are gauged to the nature of potential exposures. For instance, more data are generally needed for food use registrations than for non-food uses because of direct consumption of treated foods by the whole U.S. population. Unlike pesticide practices in many countries and authorities, as in the European Community where agricultural pesticides, non-agricultural pesticides and genetically engineered microbial agents are handled by separate directives, all pesticide activities are covered in the U.S. by the Federal Insecticide, Fungicide and Rodenticide Act. This statute covers pesticide uses on foods and animal feed and a number of non-food applications like forest and horticultural uses, residential lawn care, in-home applications, and disinfectants/sterilants. Traditional inorganic and organic chemicals are covered, as well as biological agents like pheromones. Naturally occurring and genetically altered microorganisms also come under the definition of pesticides, but multicellular animals are exempt from regulation as pesticides. Pesticide registration in the U.S. as in many other countries may be a long-term, resource intensive undertaking. Not uncommonly the process from beginning to complete registration may take 4 to 10 years and cost about $10 million. To meet the responsibilities of reviewing studies, overseeing 400 active ingredients and 35

  5. Pesticide risk assessment in the United States

    International Nuclear Information System (INIS)

    Hill, Richard N.

    1992-01-01

    In recognition of potential risks, all pesticides distributed and sold in the United States must fulfil extensive registration requirements for the Environmental Protection Agency (EPA). Registration is a licensing procedure where industry must submit data to demonstrate the safety of pesticidal substances and products before they can be used commercially. The regulatory control of pesticides is unique among chemicals in the U.S. in that testing beyond initial registration may be imposed by the Agency throughout the commercial life of the chemical, as long as there is adequate justification. Registration requirements are gauged to the nature of potential exposures. For instance, more data are generally needed for food use registrations than for non-food uses because of direct consumption of treated foods by the whole U.S. population. Unlike pesticide practices in many countries and authorities, as in the European Community where agricultural pesticides, non-agricultural pesticides and genetically engineered microbial agents are handled by separate directives, all pesticide activities are covered in the U.S. by the Federal Insecticide, Fungicide and Rodenticide Act. This statute covers pesticide uses on foods and animal feed and a number of non-food applications like forest and horticultural uses, residential lawn care, in-home applications, and disinfectants/sterilants. Traditional inorganic and organic chemicals are covered, as well as biological agents like pheromones. Naturally occurring and genetically altered microorganisms also come under the definition of pesticides, but multicellular animals are exempt from regulation as pesticides. Pesticide registration in the U.S. as in many other countries may be a long-term, resource intensive undertaking. Not uncommonly the process from beginning to complete registration may take 4 to 10 years and cost about $10 million. To meet the responsibilities of reviewing studies, overseeing 400 active ingredients and 35

  6. Fatty Acid Methyl Ester (FAME) Succession in Different Substrates as Affected by the Co-Application of Three Pesticides.

    Science.gov (United States)

    Cardinali, Alessandra; Pizzeghello, Diego; Zanin, Giuseppe

    2015-01-01

    In intensive agriculture areas the use of pesticides can alter soil properties and microbial community structure with the risk of reducing soil quality. In this study the fatty acid methyl esters (FAMEs) evolution has been studied in a factorial lab experiment combining five substrates (a soil, two aged composts and their mixtures) treated with a co-application of three pesticides (azoxystrobin, chlorotoluron and epoxiconazole), with two extraction methods, and two incubation times (0 and 58 days). FAMEs extraction followed the microbial identification system (MIDI) and ester-linked method (EL). The pesticides showed high persistence, as revealed by half-life (t1/2) values ranging from 168 to 298 days, which confirms their recalcitrance to degradation. However, t1/2 values were affected by substrate and compost age down to 8 days for chlorotoluron in S and up to 453 days for epoxiconazole in 12M. Fifty-six FAMEs were detected. Analysis of variance (ANOVA) showed that the EL method detected a higher number of FAMEs and unique FAMEs than the MIDI one, whereas principal component analysis (PCA) highlighted that the monosaturated 18:1ω9c and cyclopropane 19:0ω10c/19ω6 were the most significant FAMEs grouping by extraction method. The cyclopropyl to monoenoic acids ratio evidenced higher stress conditions when pesticides were applied to compost and compost+soil than solely soil, as well as with final time. Overall, FAMEs profiles showed the importance of the extraction method for both substrate and incubation time, the t1/2 values highlighted the effectiveness of solely soil and the less mature compost in reducing the persistence of pesticides.

  7. Fatty Acid Methyl Ester (FAME Succession in Different Substrates as Affected by the Co-Application of Three Pesticides.

    Directory of Open Access Journals (Sweden)

    Alessandra Cardinali

    Full Text Available In intensive agriculture areas the use of pesticides can alter soil properties and microbial community structure with the risk of reducing soil quality.In this study the fatty acid methyl esters (FAMEs evolution has been studied in a factorial lab experiment combining five substrates (a soil, two aged composts and their mixtures treated with a co-application of three pesticides (azoxystrobin, chlorotoluron and epoxiconazole, with two extraction methods, and two incubation times (0 and 58 days. FAMEs extraction followed the microbial identification system (MIDI and ester-linked method (EL.The pesticides showed high persistence, as revealed by half-life (t1/2 values ranging from 168 to 298 days, which confirms their recalcitrance to degradation. However, t1/2 values were affected by substrate and compost age down to 8 days for chlorotoluron in S and up to 453 days for epoxiconazole in 12M. Fifty-six FAMEs were detected. Analysis of variance (ANOVA showed that the EL method detected a higher number of FAMEs and unique FAMEs than the MIDI one, whereas principal component analysis (PCA highlighted that the monosaturated 18:1ω9c and cyclopropane 19:0ω10c/19ω6 were the most significant FAMEs grouping by extraction method. The cyclopropyl to monoenoic acids ratio evidenced higher stress conditions when pesticides were applied to compost and compost+soil than solely soil, as well as with final time.Overall, FAMEs profiles showed the importance of the extraction method for both substrate and incubation time, the t1/2 values highlighted the effectiveness of solely soil and the less mature compost in reducing the persistence of pesticides.

  8. Agricultural expansion as risk to endangered wildlife: Pesticide exposure in wild chimpanzees and baboons displaying facial dysplasia.

    Science.gov (United States)

    Krief, Sabrina; Berny, Philippe; Gumisiriza, Francis; Gross, Régine; Demeneix, Barbara; Fini, Jean Baptiste; Chapman, Colin A; Chapman, Lauren J; Seguya, Andrew; Wasswa, John

    2017-11-15

    Prenatal exposure to environmental endocrine disruptors can affect development and induce irreversible abnormalities in both humans and wildlife. The northern part of Kibale National Park, a mid-altitude rainforest in western Uganda, is largely surrounded by industrial tea plantations and wildlife using this area (Sebitoli) must cope with proximity to human populations and their activities. The chimpanzees and baboons in this area raid crops (primarily maize) in neighboring gardens. Sixteen young individuals of the 66 chimpanzees monitored (25%) exhibit abnormalities including reduced nostrils, cleft lip, limb deformities, reproductive problems and hypopigmentation. Each pathology could have a congenital component, potentially exacerbated by environmental factors. In addition, at least six of 35 photographed baboons from a Sebitoli troop (17%) have similar severe nasal deformities. Our inquiries in villages and tea factories near Sebitoli revealed use of eight pesticides (glyphosate, cypermethrin, profenofos, mancozeb, metalaxyl, dimethoate, chlorpyrifos and 2,4-D amine). Chemical analysis of samples collected from 2014 to 2016 showed that mean levels of pesticides in fresh maize stems and seeds, soils, and river sediments in the vicinity of the chimpanzee territory exceed recommended limits. Notably, excess levels were found for total DDT and its metabolite pp'-DDE and for chlorpyrifos in fresh maize seeds and in fish from Sebitoli. Imidacloprid was detected in coated maize seeds planted at the edge the forest and in fish samples from the Sebitoli area, while no pesticides were detected in fish from central park areas. Since some of these pesticides are thyroid hormone disruptors, we postulate that excessive pesticide use in the Sebitoli area may contribute to facial dysplasia in chimpanzees and baboons through this endocrine pathway. Chimpanzees are considered as endangered by IUCN and besides their intrinsic value and status as closely related to humans, they

  9. Prioritizing pesticide compounds for analytical methods development

    Science.gov (United States)

    Norman, Julia E.; Kuivila, Kathryn; Nowell, Lisa H.

    2012-01-01

    The U.S. Geological Survey (USGS) has a periodic need to re-evaluate pesticide compounds in terms of priorities for inclusion in monitoring and studies and, thus, must also assess the current analytical capabilities for pesticide detection. To meet this need, a strategy has been developed to prioritize pesticides and degradates for analytical methods development. Screening procedures were developed to separately prioritize pesticide compounds in water and sediment. The procedures evaluate pesticide compounds in existing USGS analytical methods for water and sediment and compounds for which recent agricultural-use information was available. Measured occurrence (detection frequency and concentrations) in water and sediment, predicted concentrations in water and predicted likelihood of occurrence in sediment, potential toxicity to aquatic life or humans, and priorities of other agencies or organizations, regulatory or otherwise, were considered. Several existing strategies for prioritizing chemicals for various purposes were reviewed, including those that identify and prioritize persistent, bioaccumulative, and toxic compounds, and those that determine candidates for future regulation of drinking-water contaminants. The systematic procedures developed and used in this study rely on concepts common to many previously established strategies. The evaluation of pesticide compounds resulted in the classification of compounds into three groups: Tier 1 for high priority compounds, Tier 2 for moderate priority compounds, and Tier 3 for low priority compounds. For water, a total of 247 pesticide compounds were classified as Tier 1 and, thus, are high priority for inclusion in analytical methods for monitoring and studies. Of these, about three-quarters are included in some USGS analytical method; however, many of these compounds are included on research methods that are expensive and for which there are few data on environmental samples. The remaining quarter of Tier 1

  10. Personal exposure to pesticide among workers engaged in pesticide container recycling operations.

    Science.gov (United States)

    Guidotti, T L; Yoshida, K; Clough, V

    1994-12-01

    Pesticide container handling operations in western Canada were examined to determine the exposure of workers to residual pesticide in sorting, metal-container crushing, metal-container shredding, plastic-container shredding, metal washing, and metal melting. Environmental exposure monitoring and biological monitoring were applied, including measurement of pesticide deposition density on outer clothing (test coveralls and other protective wear), deposition on fabric and gauze patches under the outer clothing, inhalation of airborne pesticide residues, dislodgement of pesticide residues by hand washing, and pre- and postexposure urinary excretion of pesticide (2,4-D). Exposure levels were highly variable; some variability was accounted for by work practices or lapses in protection. The highest levels of exposure were observed for metal washing, metal crushing, and metal shredding; sorting and plastic shredding were intermediate, and metal melting was associated with very little exposure. Urinary 2,4-D excretion, as an indicator of internal dose, correlated most closely with exposure by the inhalation route, and both were highest for metal washing and shredding. Deposition of pesticide on garments was highest for metal crushing. Melting of washed metal does not appear to present a significant hazard of exposure. Recommendations are proposed for the protection of workers emphasizing health and safety guidelines, worker education, personal hygiene, exposure and health monitoring, and record-keeping, and specific recommendations for each process. These recommendations apply to all pesticide container recycling operations except melting of washed metal containers.

  11. Use of labelled pesticides in pesticide research studies and problems in the interpretation of the data

    International Nuclear Information System (INIS)

    Sree Ramulu, U.S.; Krishnamoorthy, K.K.

    1980-01-01

    The introduction of labelled pesticides has helped to solve number of problems connected with the formation and degradation of pesticides, factors influencing the above, location of the metabolites in the plants etc. However in most of the studies, the active ingredient has been labelled and diluted and applied at the recommended doses. But the efficacy of the pesticide is modified by the method of formulation, nature of fillers, emulsifiers, solvents, size of droplets etc. Hence the utility as well as the limitations in the use of labelled pesticides in the formulations are discussed. Also due to the variations in the half life of the radioisotopes used for labelling, the use of labelled pesticides for long as well as short duration crops has also been indicated. Autoradiography has become an useful tool in studying the movement of pesticide in the plant, and insects and also locating the regions of high concentration of pesticides and their residues. Though useful, the production of artefacts caused by exudation of cell sap, and other exudates, thickness of samples, increasing time of contact in the case of low energy radioisotope labelled compounds etc. have prevented the use of this technique on a wide scale. The problems in the preparation of autoradiographs of the plant specimens treated with labelled pesticides are also discussed. (author)

  12. 75 FR 13284 - Pesticide Program Dialogue Committee; Request for Nominations to the Pesticide Program Dialogue...

    Science.gov (United States)

    2010-03-19

    ... particular interest to persons who work in agricultural settings or persons who are concerned about... entities may include, but are not limited to: Agricultural workers and farmers; pesticide industry and... and special ecosystems from potential risks posed by pesticides. The Charter for EPA's PPDC was...

  13. 40 CFR 168.22 - Advertising of unregistered pesticides, unregistered uses of registered pesticides and FIFRA...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Advertising of unregistered pesticides... ENFORCEMENT POLICIES AND INTERPRETATIONS Advertising § 168.22 Advertising of unregistered pesticides.... EPA interprets these provisions as extending to advertisements in any advertising medium to which...

  14. Review of North American Neutrino Factory R and D

    International Nuclear Information System (INIS)

    Zisman, Michael S.; Neutrino Factory and Muon Collider Collaboration

    2002-01-01

    We report here on the R and D program of the U.S. Neutrino Factory and Muon Collider Collaboration. Our effort includes work on targetry, muon ionization cooling, simulation work, and development of superconducting RF cavities. In addition, we are involved in the international effort toward a Muon Ionization Cooling Experiment (MICE). Recent activities in all these areas will be described

  15. Development in the Learning Factory: Training Human Capital.

    Science.gov (United States)

    Barton, Harry; Delbridge, Rick

    2001-01-01

    A study of human resource practices in 18 automobile factories in the United States and Britain showed that manufacturing innovations are placing greater demands on line managers and workers. Training is being refocused to develop their interpersonal, team, and leadership skills. However, lack of time and suitable training facilities are barriers.…

  16. Manufacturing data analytics using a virtual factory representation.

    Science.gov (United States)

    Jain, Sanjay; Shao, Guodong; Shin, Seung-Jun

    2017-01-01

    Large manufacturers have been using simulation to support decision-making for design and production. However, with the advancement of technologies and the emergence of big data, simulation can be utilised to perform and support data analytics for associated performance gains. This requires not only significant model development expertise, but also huge data collection and analysis efforts. This paper presents an approach within the frameworks of Design Science Research Methodology and prototyping to address the challenge of increasing the use of modelling, simulation and data analytics in manufacturing via reduction of the development effort. The use of manufacturing simulation models is presented as data analytics applications themselves and for supporting other data analytics applications by serving as data generators and as a tool for validation. The virtual factory concept is presented as the vehicle for manufacturing modelling and simulation. Virtual factory goes beyond traditional simulation models of factories to include multi-resolution modelling capabilities and thus allowing analysis at varying levels of detail. A path is proposed for implementation of the virtual factory concept that builds on developments in technologies and standards. A virtual machine prototype is provided as a demonstration of the use of a virtual representation for manufacturing data analytics.

  17. Physics of a high-luminosity Tau-Charm Factory

    International Nuclear Information System (INIS)

    King, M.E.

    1992-10-01

    This paper highlights the physics capabilities of a Tau-Charm Factory; i.e., high luminosity (∼10 33 cm -2 s -1 ) e + e - collider operating in the center-of-mass energy range of 3-5 GeV, with a high-precision, general-purpose detector. Recent developments in τ and charm physics are emphasized

  18. Lettuce growth and quality optimization in a plant factory

    NARCIS (Netherlands)

    Nicole, C.C.S.; Charalambous, F.; Martinakos, S.; De Voort, Van S.; Li, Z.; Verhoog, M.; Krijn, M.

    2016-01-01

    Since the early 2000s, plant factory (or vertical farm) technology has been introduced for growing vegetables and soft fruits. With a well-controlled environment, new health benefits, food safety, optimized nutrients and increased shelf-life can be offered to consumers. With the progress of light

  19. Introduction to radiation backgrounds in a B factory

    International Nuclear Information System (INIS)

    Khan, S.

    1992-08-01

    Detector backgrounds in a B factory due to synchrotron radiation and beam-gas interactions are discussed and the computational tools to simulate these processes are outlined. As an example of their application, simulations and beam tests that preceded the installation of the ARGUS silicon vertex detector are described. (orig.)

  20. Factorial study of rain garden design for nitrogen removal

    Science.gov (United States)

    Abstract Nitrate (〖NO〗_3^--N ) removal studies in bioretention systems showed great variability in removal rates and in some cases 〖NO〗_3^--N was exported. A 3-way factorial design (2 x 2 x 4) was devised for eight outdoor un-vegetated rain gardens to evaluate the effects of ...

  1. Mobile monitoring and embedded control system for factory environment.

    Science.gov (United States)

    Lian, Kuang-Yow; Hsiao, Sung-Jung; Sung, Wen-Tsai

    2013-12-17

    This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine) core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT) approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC) technology is used to carry out the actual electricity load experiments using smart phones.

  2. A factorial experiment on image quality and radiation dose

    International Nuclear Information System (INIS)

    Norrman, E.; Persliden, J.

    2005-01-01

    To find if factorial experiments can be used in the optimisation of diagnostic imaging, a factorial experiment was performed to investigate some of the factors that influence image quality, kerma area product (KAP) and effective dose (E). In a factorial experiment the factors are varied together instead of one at a time, making it possible to discover interactions between the factors as well as major effects. The factors studied were tube potential, tube loading, focus size and filtration. Each factor was set to two levels (low and high). The influence of the factors on the response variables (image quality, KAP and E) was studied using a direct digital detector. The major effects of each factor on the response variables were estimated as well as the interaction effects between factors. The image quality, KAP and E were mainly influenced by tube loading, tube potential and filtration. There were some active interactions, for example, between tube potential and filtration and between tube loading and filtration. The study shows that factorial experiments can be used to predict the influence of various parameters on image quality and radiation dose. (authors)

  3. Pioneering role of the KEKB B-factory

    International Nuclear Information System (INIS)

    Oide, Katsunobu

    2009-01-01

    The KEKB B-factory experimentally verified the Kobayashi-Masukawa theory, and contributed to their 2008 Nobel Prize in Physics. KEKB has realized various innovative technologies to achieve the highest luminosity in the world. KEKB has opened up a new frontier of high-luminosity colliders. (author)

  4. Factory Acceptance Test Procedure Westinghouse 100 ton Hydraulic Trailer

    International Nuclear Information System (INIS)

    Aftanas, B.L.

    1994-01-01

    This Factory Acceptance Test Procedure (FAT) is for the Westinghouse 100 Ton Hydraulic Trailer. The trailer will be used for the removal of the 101-SY pump. This procedure includes: safety check and safety procedures; pre-operation check out; startup; leveling trailer; functional/proofload test; proofload testing; and rolling load test

  5. RIKEN radioactive isotope beam factory project – Present status and ...

    Indian Academy of Sciences (India)

    Programs for studying nuclear reactions and structure of exotic nuclei available at the RIKEN radioactive isotope beam factory project are introduced and discussed by demonstrating recent highlights. Special emphasis ... RIKEN Nishina Center for Accelerator-Based Science, 2-1 Hirosawa, Wako, Saitama 351-0198, Japan ...

  6. 3D thermal climate monitoring in factory buildings

    NARCIS (Netherlands)

    Posselt, G.; Booij, P.S.; Thiede, S.; Fransman, J.E.; Driessen, B.J.F.; Herrmann, C.

    2015-01-01

    Guaranteeing defined conditions, such as the temperature levels inside the factory's building shell, is often important to produce high-quality products. Heating, ventilation and air conditioning (HVAC) equipment, as part of the technical building services, is energy intensive and accounts for a

  7. Proceedings of the tau-charm factory workshop

    International Nuclear Information System (INIS)

    Beers, L.V.

    1989-06-01

    This report contains papers on the following main topics: machine physics; tau physics; D and D s physics; J/Ψ and charmonium physics; tau charm factories; workshop summary; accelerator physics; tau physics; charmed meson physics; J/Ψ and charmonium physics; and detector

  8. Child Protection Decision Making: A Factorial Analysis Using Case Vignettes

    Science.gov (United States)

    Stokes, Jacqueline; Schmidt, Glen

    2012-01-01

    This study explored decision making by child protection social workers in the province of British Columbia, Canada. A factorial survey method was used in which case vignettes were constructed by randomly assigning a number of key characteristics associated with decision making in child protection. Child protection social workers (n = 118) assessed…

  9. Reward-allocation judgments in Romania : A factorial survey approach

    NARCIS (Netherlands)

    Buzea, C.; Meseşan-Schmitz, L.; van de Vijver, F.J.R.

    2013-01-01

    We investigated reward-allocation judgments when positive outcomes (monetary rewards) were distributed and the allocator was not a co-recipient, in a sample of 200 Romanian students. Within a full factorial survey design, seven factors, selected to affect the allocation decision, were orthogonally

  10. Two ways factorial design for round robin test of anemometers

    International Nuclear Information System (INIS)

    Cuerva, A.

    1998-01-01

    This work presents a way to carry out an inter-comparison between different cup anemometers that are tested in different wind tunnels. The method applied is known as Factorial design and allows determining the influence in the test of different factors in this case the anemometer itself and the wind tunnel where it is tested. (Author) 4 refs

  11. Designing fractional factorial split-plot experiments using integer programming

    DEFF Research Database (Denmark)

    Capehart, Shay R.; Keha, Ahmet; Kulahci, Murat

    2011-01-01

    factorial (FF) design, with the restricted randomisation structure to account for the whole plots and subplots. We discuss the formulation of FFSP designs using integer programming (IP) to achieve various design criteria. We specifically look at the maximum number of clear two-factor interactions...

  12. Constructing General Orthogonal Fractional Factorial Split-Plot Designs

    NARCIS (Netherlands)

    Sartono, B.; Goos, P.; Schoen, E.

    2015-01-01

    While the orthogonal design of split-plot fractional factorial experiments has received much attention already, there are still major voids in the literature. First, designs with one or more factors acting at more than two levels have not yet been considered. Second, published work on nonregular

  13. Neutrino Factory R and D in the U.S

    International Nuclear Information System (INIS)

    Zisman, Michael S.

    2003-01-01

    We report here on the technical progress and R andD plans of the U.S. Neutrino Factory and Muon Collider Collaboration. Programs in targetry, cooling, acceleration, and simulations are covered. U.S. activities in support of the international Muon Ionization Cooling Experiment (MICE) are also described

  14. Muon physics possibilities at a muon-neutrino factory

    NARCIS (Netherlands)

    Jungmann, KP

    2001-01-01

    New intense proton accelerators with above GeV energies and MW beam power, such as they are discussed in connection with neutrino factories, appear to be excellently suited for feeding bright muon sources for low-energy muon science. Muon rates with several orders of magnitude increased flux

  15. Limit values in special agreements between factories and sewage works

    International Nuclear Information System (INIS)

    Lundstroem, Yrjoe

    1987-01-01

    The operation of sewage works is controlled in Finland by the water and health authorities. These authorities set special quality demands for the effluent from sewage treatment plants into the recipient. Also other wastes from treatment plants, mainly sludges, have special regulations and operational target values. Sewage works have to achieve the aim goals and limit values set. In order to fulfill the regulations, sewage works impose such limit values on factory wastewaters that there will be no problems at the treatment plants. Sewage works can act in two ways: - require the factory to operate in such a way that the limit values are not exceeded, - the factory pays a certain sum of money to the sewage works, which takes care of the whole problem. It can be said in general, that it is not possible to get rid of harmful substances by payment to the sewage works if the substances cause treatment problems or problems in sludge disposal. If the factory produces wastewater that contains a higher organic load, more suspended solids or a higher nutrient load than normal sanitary wastewater, the problem is most often solved by paying an extra fee to the sewage works

  16. 29 BABY DUMPING AND EVOLVING BABY FACTORIES IN NIGERIA

    African Journals Online (AJOL)

    room for a conducive environment for child rights and social protection. ... new dimensions to include the worst of all forms of human trafficking issues ... of strict penalties for offenders in the bid to give every child born the benefit of ..... vein, the study conducted by Onuoha (2014) listed the causes of baby factory incidences to.

  17. Feasibility study for an asymmetric B-factory at KEK

    International Nuclear Information System (INIS)

    Ozaki, Hitoshi; Yoshimura, Yoshio

    1990-06-01

    In June, 1989, the study group for exploring the feasibility of B meson physics using an asymmetric energy accelerator was organized. This report is the summary of the results of the works that this study group carried out in nine months, and is the Japanese edition of the report of English edition 'Task Force Report on Asymmetric B-factory at KEK'. The activity plan of the study group was to make up the plan exceeding the preceding CLEO-2 experiment by utilizing the features of an asymmetric B-factory. Under this plan, the activities have been carried out by the study meetings twice every week on the physics side and once every two weeks on the accelerator side. Besides, in two study meetings held in October and December, 1989, several persons who have engaged in the research on B meson physics actually in foreign countries were invited, and the discussion was carried out. At present toward the materialization of the plan, the concrete investigation of accelerators and measuring instruments was begun. The significance of a B-factory and the construction project, the physics of a B-factory, the experimental method and the plan for an accelerator are reported. (K.I.)

  18. Two Ways Factorial Design for round robin test of anemometers

    Energy Technology Data Exchange (ETDEWEB)

    Cuerva, A.

    1998-07-01

    This work presents a way to carry out an inter-comparison between different cup anemometers that are tested in different wind tunnels. The method applied is known as Factorial design and allows determining the influence in the test of different factors in this case the anemometer itself and the wind tunnel where it is tested. (Author) 4 refs.

  19. Reallocating resources to focused factories: a case study in chemotherapy

    NARCIS (Netherlands)

    Vanberkel, P.T.; Boucherie, Richardus J.; Hans, Elias W.; Hurink, Johann L.; Litvak, Nelli; van Lent, W.A.M.; van Harten, Willem H.; van Harten, Wim H.; Blake, J.; Carter, M.

    2010-01-01

    This study investigates the expected service performance associated with a proposal to reallocate resources from a centralized chemotherapy department to a breast cancer focused factory. Using a slotted queueing model we show that a decrease in performance is expected and calculate the amount of

  20. Mobile Monitoring and Embedded Control System for Factory Environment

    Science.gov (United States)

    Lian, Kuang-Yow; Hsiao, Sung-Jung; Sung, Wen-Tsai

    2013-01-01

    This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine) core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT) approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC) technology is used to carry out the actual electricity load experiments using smart phones. PMID:24351642

  1. Mobile Monitoring and Embedded Control System for Factory Environment

    Directory of Open Access Journals (Sweden)

    Kuang-Yow Lian

    2013-12-01

    Full Text Available This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC technology is used to carry out the actual electricity load experiments using smart phones.

  2. A Neutrosophic Binomial Factorial Theorem with their Refrains

    Directory of Open Access Journals (Sweden)

    Huda E. Khalid

    2016-12-01

    Full Text Available The Neutrosophic Precalculus and the Neutrosophic Calculus can be developed in many ways, depending on the types of indeterminacy one has and on the method used to deal with such indeterminacy. This article is innovative since the form of neutrosophic binomial factorial theorem was constructed in addition to its refrains.

  3. Holland Code, Job Satisfaction and Productivity in Clothing Factory Workers.

    Science.gov (United States)

    Heesacker, Martin; And Others

    Published research on vocational interests and personality has not often assessed the characteristics of workers and the work environment in blue-collar, women-dominated industries. This study administered the Self-Directed Search (Form E) to 318 sewing machine operators in three clothing factories. Holland codes, productivity, job satisfaction,…

  4. Monitoring public health following a major firework factory explosion.

    NARCIS (Netherlands)

    Dirkzwager, A.J.E.; IJzermans, C.J.; Kerssens, J.J.

    2003-01-01

    Background: In May 2000, a firework factory exploded in a residential area in the Netherlands, resulting in 22 deaths, 947 wounded people, and about 2.000 severely damaged houses. Following the explosion, a largescale monitoring study was implemented to examine disaster-related health consequences

  5. Monitoring health status following a major firework factory explosion.

    NARCIS (Netherlands)

    Dirkzwager, A.; IJzermans, J.

    2003-01-01

    In May 2000, a firework factory exploded in a residential area in the Netherlands, resulting in 22 death, 947 wounded people, 500 destroyed houses, and 1.500 severely damaged houses. Following the explosion, a large-scale monitoring study was implemented to investigate disaster-related health

  6. The Layout of Power and Space in Jingdezhen Imperial Factory

    Directory of Open Access Journals (Sweden)

    Zhan Jia

    2014-12-01

    Full Text Available This paper, by referring to the archaeological reports and local gazetteers and comparing images of porcelain wares, makes a comprehensive and in-depth analysis of the layout of power and space in Jingdezhen Imperial Factory according to its geography, geomancy, security management, space regulation, architectural features, production characteristics and production layout. It contends that the Imperial Factory which integrates porcelain making factory with local government is the embodiment of absolute monarchy in ceramic culture. The factory is located on Zhushan mountain, the center of Jingdezhen’s industry, business and transportation. Being at the center, it gives off an air of prestige and majesty, overlooking dominantly the surrounding private kilns. It has also turned the political system into power operation, setting up not only workshops but also administrative offices. By taking advantage of the best resources, it has produced porcelain for imperial family and court. Its specialized production has solved the contradiction between complicated technology and numerous procedures of production. The shape, color and pattern of the porcelain wares are strictly stipulated and the best of the best wares are demanded. Hence the porcelain production is featured with longest firing, largest scale, superb craftsmanship, and best kinds of wares. All of these reveal the process and rule power and space are intersected and different cultures overlapped.

  7. Improving the Welfare of Women Factory Workers: Lessons from Indonesia.

    Science.gov (United States)

    White, Mary C.

    1990-01-01

    Attention to the quality of the working environment for women factory workers can make a real contribution to productivity. The example of an Indonesian project that introduced low-cost workplace improvements and provided health instruction shows the feasibility and effectiveness of such efforts, provided there is a clear commitment from…

  8. Beam finding algorithms at the interaction point of B factories

    International Nuclear Information System (INIS)

    Kozanecki, W.

    1992-10-01

    We review existing methods to bring beams in collision in circular machines, and examine collision alignment strategies proposed for e + e - B-factories. The two-ring feature of such machines, while imposing more stringent demands on beam control, also opens up new diagnostic possibilities

  9. Bioretention Systems: Partial Factorial Designs for Nitrate Removal

    Science.gov (United States)

    Changes in nutrient loadings are monitored by introducing captured stormwater runoff into eight outdoor rain gardens at EPA’s Urban Water Research Facility in Edison, New Jersey scaled for residential and urban landscapes. The partial factorial design includes non-vegetated meso...

  10. Search for new physics at a super-B factory

    Indian Academy of Sciences (India)

    The importance of a super- factory in the search for new physics, in particular, due to CP-odd phase(s) from physics beyond the standard model is surveyed. The first point to emphasize is that we now know how to directly measure all three angles of the unitarity triangle very cleanly, i.e. without theoretical assumptions with ...

  11. Biosensor technology for pesticides--a review.

    Science.gov (United States)

    Verma, Neelam; Bhardwaj, Atul

    2015-03-01

    Pesticides, due to their lucrative outcomes, are majorly implicated in agricultural fields for crop production enhancement. Due to their pest removal properties, pesticides of various classes have been designed to persist in the environment over a longer duration after their application to achieve maximum effectiveness. Apart from their recalcitrant structure and agricultural benefits, pesticides also impose acute toxicological effects onto the other various life forms. Their accumulation in the living system may prove to be detrimental if established in higher concentrations. Thus, their prompt and accurate analysis is a crucial matter of concern. Conventional techniques like chromatographic techniques (HPLC, GC, etc.) used for pesticides detection are associated with various limitations like stumpy sensitivity and efficiency, time consumption, laboriousity, requirement of expensive equipments and highly trained technicians, and many more. So there is a need to recruit the methods which can detect these neurotoxic compounds sensitively, selectively, rapidly, and easily in the field. Present work is a brief review of the pesticide effects, their current usage scenario, permissible limits in various food stuffs and 21st century advancements of biosensor technology for pesticide detection. Due to their exceptional performance capabilities, easiness in operation and on-site working, numerous biosensors have been developed for bio-monitoring of various environmental samples for pesticide evaluation immensely throughout the globe. Till date, based on sensing element (enzyme based, antibody based, etc.) and type of detection method used (Electrochemical, optical, and piezoelectric, etc.), a number of biosensors have been developed for pesticide detection. In present communication, authors have summarized 21st century's approaches of biosensor technology for pesticide detection such as enzyme-based biosensors, immunosensors, aptamers, molecularly imprinted polymers, and

  12. Phenomenology of neutrino oscillations at the neutrino factory

    International Nuclear Information System (INIS)

    Tang, Jian

    2011-01-01

    We consider the prospects for a neutrino factory measuring mixing angles, the CP violating phase and mass-squared differences by detecting wrong-charge muons arising from the chain μ + → ν e → ν μ → μ - and the right-charge muons coming from the chain μ + → anti ν μ → anti ν μ → μ - (similar to μ - chains), where ν e → ν μ and anti ν μ → anti ν μ are neutrino oscillation channels through a long baseline. First, we study physics with near detectors and consider the treatment of systematic errors including cross section errors, flux errors, and background uncertainties. We illustrate for which measurements near detectors are required, discuss how many are needed, and what the role of the flux monitoring is. We demonstrate that near detectors are mandatory for the leading atmospheric parameter measurements if the neutrino factory has only one baseline, whereas systematic errors partially cancel if the neutrino factory complex includes the magic baseline. Second, we perform the baseline and energy optimization of the neutrino factory including the latest simulation results from the magnetized iron neutrino detector (MIND). We also consider the impact of τ decays, generated by appearance channels ν μ → ν τ and ν e → ν τ , on the discovery reaches of the mass orderings, the leptonic CP violation, and the non-zero θ 13 , which we find to be negligible for the considered detector. Third, we make a comparison of a high energy neutrino factory to a low energy neutrino factory and find that they are just two versions of the same experiment optimized for different regions of the parameter space. In addition, we briefly comment on whether it is useful to build the bi-magic baseline at the low energy neutrino factory. Finally, the effects of one additional massive sterile neutrino are discussed in the context of a combined short and long baseline setup. It is found that near detectors can provide the required sensitivity at the

  13. Phenomenology of neutrino oscillations at the neutrino factory

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Jian

    2011-12-19

    We consider the prospects for a neutrino factory measuring mixing angles, the CP violating phase and mass-squared differences by detecting wrong-charge muons arising from the chain {mu}{sup +} {yields} {nu}{sub e} {yields} {nu}{sub {mu}} {yields} {mu}{sup -} and the right-charge muons coming from the chain {mu}{sup +} {yields} anti {nu}{sub {mu}} {yields} anti {nu}{sub {mu}} {yields} {mu}{sup -} (similar to {mu}{sup -} chains), where {nu}{sub e} {yields} {nu}{sub {mu}} and anti {nu}{sub {mu}} {yields} anti {nu}{sub {mu}} are neutrino oscillation channels through a long baseline. First, we study physics with near detectors and consider the treatment of systematic errors including cross section errors, flux errors, and background uncertainties. We illustrate for which measurements near detectors are required, discuss how many are needed, and what the role of the flux monitoring is. We demonstrate that near detectors are mandatory for the leading atmospheric parameter measurements if the neutrino factory has only one baseline, whereas systematic errors partially cancel if the neutrino factory complex includes the magic baseline. Second, we perform the baseline and energy optimization of the neutrino factory including the latest simulation results from the magnetized iron neutrino detector (MIND). We also consider the impact of {tau} decays, generated by appearance channels {nu}{sub {mu}} {yields} {nu}{sub {tau}} and {nu}{sub e} {yields} {nu}{sub {tau}}, on the discovery reaches of the mass orderings, the leptonic CP violation, and the non-zero {theta}{sub 13}, which we find to be negligible for the considered detector. Third, we make a comparison of a high energy neutrino factory to a low energy neutrino factory and find that they are just two versions of the same experiment optimized for different regions of the parameter space. In addition, we briefly comment on whether it is useful to build the bi-magic baseline at the low energy neutrino factory. Finally, the

  14. Pesticide poisoning in the developing world--a minimum pesticides list

    DEFF Research Database (Denmark)

    Eddleston, Michael; Karalliedde, Lakshman; Buckley, Nick

    2002-01-01

    In parts of the developing world, pesticide poisoning causes more deaths than infectious diseases. Use of pesticides is poorly regulated and often dangerous; their easy availability also makes them a popular method of self-harm. In 1985, the UN Food and Agriculture Organisation (FAO) produced...... a voluntary code of conduct for the pesticide industry in an attempt to limit the harmful effects of pesticides. Unfortunately, a lack of adequate government resources in the developing world makes this code ineffective, and thousands of deaths continue today. WHO has recommended that access to highly toxic...... to do specific tasks within an integrated pest management system. Use of safer pesticides should result in fewer deaths, just as the change from barbiturates to benzodiazepines has reduced the number of deaths from pharmaceutical self-poisoning....

  15. 40 CFR 158.2170 - Experimental use permit data requirements-microbial pesticides.

    Science.gov (United States)

    2010-07-01

    ... requirements-microbial pesticides. 158.2170 Section 158.2170 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Microbial Pesticides § 158.2170 Experimental use permit data requirements—microbial pesticides. (a) For all microbial pesticides. (1) The...

  16. Energy usage in Beet Suger Factories. Sockerfabrikens energianvaendning; En systemstudie

    Energy Technology Data Exchange (ETDEWEB)

    Feltborg, G

    1990-02-01

    A computer program has been developed in order to simulate the energy consumption of beet sugar factories, for various plant configurations. The program is divided into five block units: Extraction and Juice purification, Juice concentration, Crystallization, Drying and finally the Power House. Each block consists of different modules, for example, a heat exchanger, an evaporator, a turbine and a dryer. The purpose of this project was to simulate some different system configurations of a sugar factory, whereby both new and previously used process technologies were utilized. The following parts of the process have been particularly emphasized: Power House - gas turbine, waste heat boiler. Drying - low-temperature dryer, steam dryer. Evaporation - vapour recompression. Crystallization - vapour recompression, continuous system. The different plant configurations have been compared to a reference factory, which is designed according to current technology used in a modern and well balanced Swedish factory. The comparisons are based upon the total power consumption as well as the total annual energy costs. Eleven different plant configurations were studied. The maximum power reduction is 36%, relative to the reference factory. The dissertation also contains an experimental study of a low-temperature drying process. The drying characteristics of pressed beet pulp were studied in a specially designed rotary dryer pilot plant. A number of parameters were varied i.e. the solid moisture content, air velocity, temperature and rotational speed. The results are given in terms of an apparent volumetric heat-transfer coefficient, determined from measured data. A mathematical model was established to determine the residence time of the material in the rotary dryer at different air velocities. (45 refs.).

  17. Novel GABA receptor pesticide targets.

    Science.gov (United States)

    Casida, John E; Durkin, Kathleen A

    2015-06-01

    The γ-aminobutyric acid (GABA) receptor has four distinct but overlapping and coupled targets of pesticide action importantly associated with little or no cross-resistance. The target sites are differentiated by binding assays with specific radioligands, resistant strains, site-directed mutagenesis and molecular modeling. Three of the targets are for non-competitive antagonists (NCAs) or channel blockers of widely varied chemotypes. The target of the first generation (20th century) NCAs differs between the larger or elongated compounds (NCA-IA) including many important insecticides of the past (cyclodienes and polychlorocycloalkanes) or present (fiproles) and the smaller or compact compounds (NCA-IB) highly toxic to mammals and known as cage convulsants, rodenticides or chemical threat agents. The target of greatest current interest is designated NCA-II for the second generation (21st century) of NCAs consisting for now of isoxazolines and meta-diamides. This new and uniquely different NCA-II site apparently differs enough between insects and mammals to confer selective toxicity. The fourth target is the avermectin site (AVE) for allosteric modulators of the chloride channel. NCA pesticides vary in molecular surface area and solvent accessible volume relative to avermectin with NCA-IBs at 20-22%, NCA-IAs at 40-45% and NCA-IIs at 57-60%. The same type of relationship relative to ligand-docked length is 27-43% for NCA-IBs, 63-71% for NCA-IAs and 85-105% for NCA-IIs. The four targets are compared by molecular modeling for the Drosophila melanogaster GABA-R. The principal sites of interaction are proposed to be: pore V1' and A2' for NCA-IB compounds; pore A2', L6' and T9' for NCA-IA compounds; pore T9' to S15' in proximity to M1/M3 subunit interface (or alternatively an interstitial site) for NCA-II compounds; and M1/M3, M2 interfaces for AVE. Understanding the relationships of these four binding sites is important in resistance management and in the discovery and use

  18. Avoid Counterfeit Pesticide Products for Dogs and Cats

    Science.gov (United States)

    EPA is aware of counterfeit pet pesticides designed to look like legitimately registered pesticide products. The information on this page is intended to help consumers avoid unregistered pet products.

  19. Effects of Pesticide Application on the Growth of Soil Nitrifying ...

    African Journals Online (AJOL)

    ADOWIE PERE

    shows that the bacteria could survive and grow at lower pesticide concentrations but were completely ... soil bacteria before application. .... capacities to degrade or utilize pesticides as carbon ... effects of plastic composted soil on nitrifying.

  20. STORAGE STABILITY OF PESTICIDES IN EXTRACT SOLVENTS AND SAMPLING MEDIA

    Science.gov (United States)

    Demonstrating that pesticides are stable in field media and their extracts over extended storage periods allows operational flexibility and cost efficiency. Stability of the 31 neutral pesticides and 2 acid herbicides of the Agricultural Health Study exposure pilot was evaluate...