WorldWideScience

Sample records for peroxide mechanical pulping

  1. HYDROGEN PEROXIDE BLEACHING OF CMP PULP USING MAGNESIUM HYDROXIDE

    Directory of Open Access Journals (Sweden)

    Farhad Zeinaly

    2009-11-01

    Full Text Available Conventional bleaching of hardwood CMP pulp with magnesium hydroxide (Mg(OH2 show significant benefits over bleaching with sodium hydroxide (NaOH under various conditions. Magnesium hydroxide bleaching generate higher optical properties, higher pulp yield and lower effluent COD at the same chemical charge, but the physical properties were found to be similar for both processes. The initial freeness of the bleached pulps and refining value to reach a target freeness (about 350 ml. CSF were more for the Mg(OH2-based process. The residual peroxide of filtrate from the Mg(OH2-based process was very high as compared to conventional bleaching.

  2. MOLYBDENUM CATALYZED ACID PEROXIDE BLEACHING OF EUCALYPTUS KRAFT PULP

    Directory of Open Access Journals (Sweden)

    Marcos S. Rabelo

    2008-08-01

    Full Text Available Molybdenum catalyzed peroxide bleaching (PMo Stage consists of pulp treatment with hydrogen peroxide under acidic conditions in the presence of a molybdenum catalyst. Molybdenum is applied in catalytic doses (50-200 mg/kg pulp and may originate from various sources, including (NH46Mo7O24.4H2O, Na2MoO4.2H2O, siliconmolybdate, etc. This work is aimed at optimizing the PMo stage and evaluating its industrial application in the OAZDP sequence. Optimum PMo stage conditions for bleaching eucalyptus pulp were 90 ºC, pH 3.5, 2 h, 0.1 kg/adt Mo and 5 kg/adt H2O2. The PMo stage was more efficient to remove pulp hexenuronic acids than lignin. Its efficiency decreased with increasing pH in the range of 1.5-5.5, while it increased with increasing temperature and peroxide and molybdenum doses. The application of the PMo stage as replacement for the A-stage of the AZDP sequence significantly decreased chlorine dioxide demand. The PMo stage caused a decrease of 20-30% in the generation of organically bound chlorine. The quality parameters of the pulp produced during the PMo stage mill trial were comparable to those obtained with the reference A-stage.

  3. Kraft pulp bleaching with molybdenum activated acid peroxide (PMo stage)

    International Nuclear Information System (INIS)

    Rabelo, Marcos Sousa

    2009-01-01

    Optimum conditions to run the P Mo stage for bleaching eucalyptus kraft pulp were 90 deg C, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H 2 O 2 . The P Mo stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 deg C), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P Mo stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO. (author)

  4. Arundo donax L. reed: new perspectives for pulping and bleaching. Part 4. Peroxide bleaching of organosolv pulps.

    Science.gov (United States)

    Shatalov, A A; Pereira, H

    2005-05-01

    A comparative study on TCF (totally chlorine-free) bleachability of organosolv pulps from the annual fibre crop Arundo donax L. (giant reed) was carried out using a simple three-stage peroxide bleaching sequence without oxygen pre-bleaching. ASAM (alkali-sulfite-anthraquinone-methanol), Organocell (alkali-anthraquinone-methanol) and ethanol-soda organosolv pulps were bleached and compared with kraft pulp, as a reference. The final brightness of 76-78% ISO was attained for all tested pulps. The chemical charge required to reach this level of brightness varied for different pulps (despite the equal initial content of the residual lignin) and directly related to starting brightness values. No direct correlation between brightness improvement and lignin removal during bleaching was found, indicating the influence of the specific pulp properties introduced by pulping process on bleaching chemistry. The general higher bleaching response of organosolv pulps from A. donax was noted in comparison with kraft.

  5. Fabrication of microfibrillated cellulose gel from waste pulp sludge via mild maceration combined with mechanical shearing

    Science.gov (United States)

    Nusheng Chen; Junyong Zhu; Zhaohui Tong

    2016-01-01

    This article describes a facile route, which combines mild maceration of waste pulp sludge and a mechanical shearing process, to prepare microfibrillated cellulose (MFC) with a high storage modulus. In the maceration, the mixture of glacial acetic acid and hydrogen peroxide was used to extract cellulose from never-dried waste pulp sludge. Then, two different mechanical...

  6. High levels of hydrogen peroxide in overnight tooth-whitening formulas: effects on enamel and pulp.

    Science.gov (United States)

    Pugh, George; Zaidel, Lynette; Lin, Nora; Stranick, Michael; Bagley, Daniel

    2005-01-01

    Limited data are available to assess the safety of high levels of hydrogen peroxide in overnight tooth-whitening formulas. The purpose of this study was to assess the effects of hydrogen peroxide on enamel microhardness, pulp penetration, and enamel morphology. Colgate Platinum Professional Overnight Whitening System (Colgate Oral Pharmaceuticals, Inc., Canton, MA, USA) (10% carbamide peroxide, equivalent to 3.5% hydrogen peroxide) was compared with two prototype formulations containing either 7.0% or 12.0% hydrogen peroxide. In the pulp chamber studies, human extracted teeth were exposed to 3.5%, 7.0%, or 12.0% hydrogen peroxide for 30 minutes, 4 hours, or 7 hours. Microhardness, electron spectroscopy for chemical analysis, and atomic force microscopy evaluations were made from enamel blocks cut from human extracted molars. The enamel blocks were evaluated following 14 7-hour treatments (98 h total). At 7 hours' post-treatment, hydrogen peroxide penetrated the pulp chamber at 23.12 +/- 10.09, 24.58 +/- 6.90, and 26.39 +/- 5.43 microg for 3.5%, 7.0%, and 12.0% hydrogen peroxide, respectively. With regard to enamel morphology, pulp penetration, microhardness, and elemental composition, no statistically significant differences were observed between treatment groups following 98 hours of treatment. Hydrogen peroxide does not adversely affect enamel morphology or microhardness. The levels recovered in pulp indicate that hydrogen peroxide is not expected to inhibit pulpal enzymes. Overnight tray products containing levels of hydrogen peroxide of 3.5%, 7.0%, and 12.0% are not expected to adversely affect the enamel or pulpal enzymes. Additional safety studies are needed to assess the potential for tooth sensitivity and gingival irritation.

  7. Ranking mechanical pulps for their potential to photoyellow

    Science.gov (United States)

    Umesh P. Agarwal

    2000-01-01

    Recently found experimental evidence has provided strong support for an alternative photoyellowing mechanism that suggests that pulp- photoyellowing occurs due to direct photooxidation of hydroquinones (present in mechanical pulps) top-quinones. Because hydroquinones were found to be present in pulps, it may be possible to quantify them. Quantification of mechanical-...

  8. A clinical assessment of the effects of 10% carbamide peroxide gel on human pulp tissue.

    Science.gov (United States)

    Anderson, D G; Chiego, D J; Glickman, G N; McCauley, L K

    1999-04-01

    Bleaching vital teeth with 10% carbamide peroxide gel is a routine procedure in which there has been no evidence of associated permanent pulpal damage. Synthesis of the enzyme heme oxygenase-1 (HO-1) is increased after exposure of eukaryotic cells to conditions of oxidative stress (including H2O2) as a defense against the damaging effects of free radicals. Dental pulps were evaluated for HO-1 (aka Heat Shock Protein 32) presence in teeth treated with 10% carbamide peroxide. Seventeen intact first premolars scheduled for orthodontic extraction were bleached for 4 h immediately preceding extraction. Fourteen additional premolars from the same individuals were not bleached. All 31 teeth were extracted, fixed, demineralized, frozen, sectioned, and immunostained with anti-HO-1 antibody using a standard ABC protocol. There was no significant difference in the presence of HO-1 between total bleached versus total unbleached teeth using the Fisher's Exact Test (p pulp proper may have the potential to respond to oxidative stress by increasing the synthesis of HO-1 (HSP32). This could represent a component of an initial defensive response by specific cells in strategic locations in the pulp that precedes classical inflammatory pathways.

  9. Mechanisms of wet oxidation by hydrogen peroxide

    International Nuclear Information System (INIS)

    Baxter, R.A.

    1987-08-01

    A research programme is currently under way at BNL and MEL to investigate the possible use of Hydrogen Peroxide with metal ion catalysts as a wet oxidation treatment system for CEGB organic radioactive wastes. The published literature relating to the kinetics and mechanism of oxidation and decomposition reactions of hydrogen peroxide is reviewed and the links with practical waste management by wet oxidation are examined. Alternative wet oxidation systems are described and the similarities to the CEGB research effort are noted. (author)

  10. Effect of ultrasonic pre-treatment of thermomechanical pulp on hydrogen peroxide bleaching

    Science.gov (United States)

    Loranger, E.; Charles, A.; Daneault, C.

    2012-12-01

    Ultrasound pre-treatments of softwood TMP had been carried to evaluate its impact on the efficiency of hydrogen peroxide bleaching. The trials were performed after a factorial design of experiment using frequency, power and time as variables. The experiments were conducted in an ultrasonic bath and then bleached with hydrogen peroxide. Measurements such as brightness, L*A*B* color system coordinate, residual hydrogen peroxide and metal content were evaluated on bleached pulp. The results indicate that the effect of ultrasonic treatment on brightness was dependent on the ultrasound frequency used; the brightness increased slightly at 68 kHz and decreased at 40 and 170 kHz. These results were correlated to the ultrasound effect on the generation of transition metals (copper, iron and manganese) which are responsible for catalytic decomposition of hydrogen peroxide. The influence of metal interference was minimized by using a chelating agent such as diethylene triamine pentaacetic acid (DTPA). With the results obtained in this study we have identified a set of option conditions, e.g. 1000 W, 40 kHz, 1.5 % consistency and 0.2% addition of DTPA prior to the bleaching stage (after ultrasonic pre-treatment) who improve brightness by 2.5 %ISO.

  11. The Use of Mg(OH2 in the Final Peroxide Bleaching Stage of Wheat Straw Pulp

    Directory of Open Access Journals (Sweden)

    Yan-Lan Liu

    2013-11-01

    Full Text Available Magnesium-based alkali is an attractive alkaline source for the peroxide bleaching of high-yield pulp. However, little information is available on Mg(OH2 application in the final peroxide bleaching stage of wheat straw pulp. The use of Mg(OH2 was demonstrated as a partial replacement for NaOH in the peroxide bleaching of a chelated oxygen-delignified wheat straw pulp. The yield, viscosity, and strength properties of bleached pulp significantly increased with increasing replacement ratio of Mg(OH2, while the chemical oxygen demand load (COD of filtrate was decreased. For similar brightness of bleached pulp at a 24% replacement ratio of Mg(OH2, the tensile and tear indices were higher, by 2.1 Nm.g-1 and 1.75 mN*m2.g-1, respectively, than that of control pulp bleached with NaOH as the sole alkaline source. When the MgSO4 was eliminated and the dosage of Na2SiO3 was decreased in the bleaching process, the tear and burst indices of the bleached pulp were also enhanced, with the brightness maintained. Scanning electron microscopy (SEM showed that more swelling occurred in the fibers of bleached pulp from the Mg(OH2-based bleaching process. Fiber analysis indicated that peroxide bleaching with Mg(OH2 increased the proportion of fiber lengths between 0.20 to 1.20 mm and 1.20 to 7.60 mm.

  12. Alkaline peroxide treatment of ECF bleached softwood kraft pulps: part 2. effect of increased fiber charge on refining, wet-end application, and hornification

    Science.gov (United States)

    Zheng Dang; Thomas Elder; Jeffery S. Hsieh; Arthur J. Ragauskas

    2007-01-01

    The effect of increased fiber charge on refining, cationic starch adsorption, and hornification was examined. Two pulps were investigated: (1) a softwood (SW) kraft pulp (KP) which was bleached elementally chlorine-free (ECF) and sewed as control; and (2) a control pulp treated with alkaline peroxide, which had a higher fiber charge. It was shown that increased fiber...

  13. Penetration of 35% hydrogen peroxide into the pulp chamber in bovine teeth after LED or Nd:YAG laser activation.

    Science.gov (United States)

    Camargo, Samira Esteves Afonso; Cardoso, Paula Elaine; Valera, Marcia Carneiro; de Araújo, Maria Amélia Máximo; Kojima, Alberto Noriyuki

    2009-01-01

    This aim of the present study was to evaluate the pulp chamber penetration of 35% hydrogen peroxide activated by LED (light-emitting diode) or Nd:YAG laser in bovine teeth, after an in-office bleaching technique. Forty-eight bovine lateral incisors were divided into four groups, acetate buffer was placed into the pulp chamber and bleaching agent was applied as follows: for group A (n = 12), activation was performed by LED; for group B (n = 12), activation was performed by Nd:YAG laser (60 mJ, 20 Hz); group C (n = 12) received no light or laser activation; and the control group (n = 12) received no bleaching gel application or light or laser activation. The acetate buffer solution was transferred to a glass tube and Leuco Crystal Violet and horseradish peroxidase were added, producing a blue solution. The optical density of this solution was determined spectrophotometrically and converted into microgram equivalents of hydrogen peroxide. The results were analysed using ANOVA and Tukey's test (5%). It was verified that the effect of activation was significant, as groups activated by LED or laser presented greater hydrogen peroxide penetration into the pulp chamber (0.499 +/- 0.622 microg) compared with groups that were not (0.198 +/- 0.218 microg). There was no statistically significant difference in the penetration of hydrogen peroxide into the pulp chamber between the two types of activation (LED or laser). The results suggest that activation by laser or LED caused an increase in hydrogen peroxide penetration into the pulp chamber.

  14. Penetration of 38% hydrogen peroxide into the pulp chamber in bovine and human teeth submitted to office bleach technique.

    Science.gov (United States)

    Camargo, Samira Esteves Afonso; Valera, Marcia Carneiro; Camargo, Carlos Henrique Ribeiro; Gasparoto Mancini, Maria Nadir; Menezes, Marcia Maciel

    2007-09-01

    This study evaluated the pulp chamber penetration of peroxide bleaching agent in human and bovine teeth after office bleach technique. All the teeth were sectioned 3 mm apical of the cement-enamel junction and were divided into 2 groups, A (70 third human molars) and B (70 bovine lateral incisors), that were subdivided into A1 and B1 restored by using composite resin, A2 and B2 by using glass ionomer cement, and A3 and B3 by using resin-modified glass ionomer cement; A4, A5, B4, and B5 were not restored. Acetate buffer was placed in the pulp chamber, and the bleaching agent was applied for 40 minutes as follows: A1-A4 and B1-B4, 38% hydrogen peroxide exposure and A5 and B5, immersion into distilled water. The buffer solution was transferred to a glass tube in which leuco crystal violet and horseradish peroxidase were added, producing a blue solution. The optical density of the blue solution was determined by spectrophotometer and converted into microgram equivalents of hydrogen peroxide. Data were submitted to analysis of variance and Dunnett, Kruskal-Wallis, and Tukey tests (5%). A higher level of hydrogen peroxide penetrated into the pulp chamber in resin-modified glass ionomer cements in bovine (0.79 +/- 0.61 microg) and human (2.27 +/- 0.41 microg) groups. The bleaching agent penetration into the pulp chamber was higher in human teeth for any experimental situation. The penetration of the hydrogen peroxide depends on restorative materials, and under the conditions of this study human teeth are more susceptible to penetration of bleaching agent into the pulp chamber than bovine teeth.

  15. Effects of the concentration and composition of in-office bleaching gels on hydrogen peroxide penetration into the pulp chamber.

    Science.gov (United States)

    Mena-Serrano, A P; Parreiras, S O; do Nascimento, E M S; Borges, C P F; Berger, S B; Loguercio, A D; Reis, A

    2015-01-01

    In tooth whitening, the hydrogen peroxide (HP) diffuses in the enamel and dentin, reaching the pulp. This in vitro study aimed to quantify the penetration of HP in the pulp chamber in teeth submitted to bleaching agents of different concentrations of HP without calcium (HP 20% [20CF], HP 35% [35CF]) and with calcium (HP 20% [20CC], HP 35% [35CC]). Fifty human premolars were sectioned 3 mm from the cemento-enamel junction and the pulp tissue was removed. The teeth were divided into five groups according to treatment and with a control group (n=10). An acetate buffer solution was placed in the pulp chamber of all teeth. The control group was exposed only to distilled water, while the other groups were treated with a bleaching procedure, according to the manufacturer's recommendations. After treatment, the acetate buffer solution was transferred to a glass tube in which leuco-crystal violet and peroxidase solutions were added, resulting in a blue solution. The optical density of this blue solution was determined spectrophotometrically and converted into micrograms equivalent to the HP. Data were analyzed using analysis of variance and Tukey tests (α=0.05). The HP concentration did not affect the HP inside the pulp chamber, but the presence of calcium significantly reduced it (p<0.0001). The amount of HP that reaches the pulp chamber depends on the bleaching protocol and the product employed, and it seems to be less affected by HP concentration.

  16. Dental Pulp Defence and Repair Mechanisms in Dental Caries.

    Science.gov (United States)

    Farges, Jean-Christophe; Alliot-Licht, Brigitte; Renard, Emmanuelle; Ducret, Maxime; Gaudin, Alexis; Smith, Anthony J; Cooper, Paul R

    2015-01-01

    Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and reducing innate repair capacities. For complete tooth healing the formation of a reactionary/reparative dentin barrier to distance and protect the pulp from infectious agents and restorative materials is required. Clinical and in vitro experimental data clearly indicate that dentin barrier formation only occurs when pulp inflammation and infection are minimised, thus enabling reestablishment of tissue homeostasis and health. Therefore, promoting the resolution of pulp inflammation may provide a valuable therapeutic opportunity to ensure the sustainability of dental treatments. This paper focusses on key cellular and molecular mechanisms involved in pulp responses to bacteria and in the pulpal transition between caries-induced inflammation and dentinogenic-based repair. We report, using selected examples, different strategies potentially used by odontoblasts and specialized immune cells to combat dentin-invading bacteria in vivo.

  17. Dental Pulp Defence and Repair Mechanisms in Dental Caries

    Directory of Open Access Journals (Sweden)

    Jean-Christophe Farges

    2015-01-01

    Full Text Available Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and reducing innate repair capacities. For complete tooth healing the formation of a reactionary/reparative dentin barrier to distance and protect the pulp from infectious agents and restorative materials is required. Clinical and in vitro experimental data clearly indicate that dentin barrier formation only occurs when pulp inflammation and infection are minimised, thus enabling reestablishment of tissue homeostasis and health. Therefore, promoting the resolution of pulp inflammation may provide a valuable therapeutic opportunity to ensure the sustainability of dental treatments. This paper focusses on key cellular and molecular mechanisms involved in pulp responses to bacteria and in the pulpal transition between caries-induced inflammation and dentinogenic-based repair. We report, using selected examples, different strategies potentially used by odontoblasts and specialized immune cells to combat dentin-invading bacteria in vivo.

  18. Mechanical pulping with a sequential velocity refiner- a new concept

    Science.gov (United States)

    C.W. McMillin

    1978-01-01

    In previous research with refiner mechanical pulps, a theoretical stress analysis indicated that longitudinal tracheids of Pinus taeda L. fail while under torsional stress and unwind into ribbonlike elements that provide the coherence necessary for strength development. When macerated tracheids of loblolly pine were individually stressed in torsion...

  19. Possible mechanism for anthraquinone species diffusion in alkaline pulping

    Science.gov (United States)

    X.-S. Chai; J. Samp; Q.X. Hou; S.-H Yoon; J.Y. Zhu

    2007-01-01

    An analysis of the effectiveness of anthraquinone (AQ) in kraft-AQ pulping in terms of its mechanism of transport has been conducted. Our previous work showed that caustic solutions of wood lignin can decrease the membrane exclusion for anthraquinones, i.e., the presence of wood lignin enhances the ability of AQ to pass through a membrane when a reducing agent is...

  20. A comparative evaluation of explosion hazards in chemical and mechanical pulp bleaching systems

    Science.gov (United States)

    Peter W. Hart; Alan W. Rudie

    2010-01-01

    Over the past several years, at least three pulp mills in North America have experienced catastrophic events that resulted in the explosion of pumps, mixers, and tanks. All these mills were using 50% concentration hydrogen peroxide at the site of the explosions. In at least two instances, alkali catalyzed decomposition of peroxide is implicated in the explosion....

  1. Effect of fluoride-treated enamel on indirect cytotoxicity of a 16% carbamide peroxide bleaching gel to pulp cells.

    Science.gov (United States)

    Soares, Diana Gabriela; Ribeiro, Ana Paula Dias; Lima, Adriano Fonseca; Sacono, Nancy Tomoko; Hebling, Josimeri; de Souza Costa, Carlos Alberto

    2013-01-01

    The aim of this study was to evaluate the possibility of fluoride solutions applied to enamel to protect pulp cells against the trans-enamel and transdentinal cytotoxicity of a 16% carbamide peroxide (CP) bleaching gel. The CP gel was applied to enamel/dentin discs adapted to aicial pulp chambers (8 h/day) during 1, 7 or 14 days, followed by fluoride (0.05% or 0.2%) application for 1 min. The extracts (culture medium in contact with dentin) were applied to MDPC-23 cells for 1 h, and cell metabolism (MTT assay), alkaline phosphatase (ALP) activity and cell membrane damage (flow cytometry) were analyzed. Knoop microhardness of enamel was also evaluated. Data were analyzed statistically by ANOVA and Kruskal-Wallis tests (α=0.05). For the MTT assay and ALP activity, significant reductions between the control and the bleached groups were observed (p0.05), regardless of fluoride application or treatment days. Flow cytometry analysis demonstrated 30% of cell membrane damage in all bleached groups. After 14 days of treatment, the fluoride-treated enamel presented significantly higher microhardness values than the bleached-only group (pfluoride solutions, the treated enamel surface did not prevent the toxic effects caused by the 16% CP gel to odontoblast-like cells.

  2. Protective Effect of Pulp Oil Extracted from Canarium odontophyllum Miq. Fruit on Blood Lipids, Lipid Peroxidation, and Antioxidant Status in Healthy Rabbits

    Directory of Open Access Journals (Sweden)

    Faridah Hanim Shakirin

    2012-01-01

    Full Text Available The aim of this paper was to compare the effects of pulp and kernel oils of Canarium odontophyllum Miq. (CO on lipid profile, lipid peroxidation, and oxidative stress of healthy rabbits. The oils are rich in SFAs and MUFAs (mainly palmitic and oleic acids. The pulp oil is rich in polyphenols. Male New Zealand white (NZW rabbits were fed for 4 weeks on a normal diet containing pulp (NP or kernel oil (NK of CO while corn oil was used as control (NC. Total cholesterol (TC, HDL-C, LDL-c and triglycerides (TG levels were measured in this paper. Antioxidant enzymes (superoxide dismutase and glutathione peroxidise, thiobarbiturate reactive substances (TBARSs, and plasma total antioxidant status (TAS were also evaluated. Supplementation of CO pulp oil resulted in favorable changes in blood lipid and lipid peroxidation (increased HDL-C, reduced LDL-C, TG, TBARS levels with enhancement of SOD, GPx, and plasma TAS levels. Meanwhile, supplementation of kernel oil caused lowering of plasma TC and LDL-C as well as enhancement of SOD and TAS levels. These changes showed that oils of CO could be beneficial in improving lipid profile and antioxidant status as when using part of normal diet. The oils can be used as alternative to present vegetable oil.

  3. Dental Pulp Defence and Repair Mechanisms in Dental Caries

    OpenAIRE

    Farges, Jean-Christophe; Alliot-Licht, Brigitte; Renard, Emmanuelle; Ducret, Maxime; Gaudin, Alexis; Smith, Anthony J.; Cooper, Paul R.

    2015-01-01

    Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and red...

  4. Kraft pulp bleaching with molybdenum activated acid peroxide (P{sub Mo} stage); Branqueamento de polpa celulosica kraft de eucalipto com peroxido acido ativado por molibdenio

    Energy Technology Data Exchange (ETDEWEB)

    Rabelo, Marcos Sousa [Servico Nacional de Aprendizagem Industrial (SENAI), Lauro de Freitas, BA (Brazil). Dept. Regional da Bahia; Silva, Vanessa Lopes; Barros, Denise Pires de; Colodette, Jorge Luiz [Universidade Federal de Vicosa (UFV), MG (Brazil). Dept. de Engenharia Florestal; Sacon, Vera Maria; Silva, Marcelo Rodrigues da [Votorantim Celulose e Papel, Jacarei, SP (Brazil)

    2009-07-01

    Optimum conditions to run the P{sub Mo} stage for bleaching eucalyptus kraft pulp were 90 deg C, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H{sub 2}O{sub 2}. The P{sub Mo} stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 deg C), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P{sub Mo} stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO. (author)

  5. Effect of Bagasse Chemical Pulping and Coupling Agent on the Physical - Mechanical Properties of Composites Based on Bagasse pulp/Low density polyethylene

    Directory of Open Access Journals (Sweden)

    maryam allahdadi

    2016-12-01

    Full Text Available In this research, effect of reinforcing bagasse pulp and raw bagasse fibers and applying coupling agent MAPE (Maleic Anhydride Polyethylene on physical-mechanical properties of low density polyethylene (LDPE composites were studided. Fresh bagasse were collected from an experimental field in Khuzestan and after investigating anatomy and chemical properties of Different pulp fibers including monoethanolamine (MEA bagasse pulp, alkaline sulfite-anthraquinone (AS bagasse pulp, bleached soda (BS bagasse pulp, unbleached soda (UNS bagasse pulp and raw bagasse fibers (B were prepared. Then, composites with 30wt.% fiber content were manufactured by twin-screw extrusion followed by compression molding processing. The mechanical and physical properties of these composites were analyzed and compared. Results revealed that the chemical pulping dissolved a fraction of lignin and hemicelluloses so that the linkage potential and aspect ratio of bagasse fibers was improved and consequently, as compared with the raw bagasse fibers, bagasse pulp fibers have better reinforcing capability. The best overall properties were achieved with MEA and AS/AQ fibers. Addition of 5% (wt/wt of coupling agent MAPE resulted in a significant enhancement in the tensile strength, tensile modulus and impact strength in line with the improvement of the fiber-matrix interfacial adhesion making more effective the transfer of stress from the matrix to the rigid reinforcement.

  6. Microsomal lipid peroxidation as a mechanism of cellular damage. [Dissertation

    Energy Technology Data Exchange (ETDEWEB)

    Kornbrust, D.J.

    1979-01-01

    The NADPH/iron-dependent peroxidation of lipids in rat liver microsomes was found to be dependent on the presence of free ferrous ion and maintains iron in the reduced Fe/sup 2 +/ state. Chelation of iron by EDTA inhibited peroxidation. Addition of iron, after preincubation of microsomes in the absence of iron, did not enhance the rate of peroxidation suggesting that iron acts by initiating peroxidative decomposition of membrane lipids rather than by catalyzing the breakdown of pre-formed hydroperoxides. Liposomes also underwent peroxidation in the presence of ferrous iron at a rate comparable to intact microsomes and was stimulated by ascorbate. Carbon tetrachloride initiated lipid peroxidation in the absence of free metal ions. Rates of in vitro lipid peroxidation of microsomes and homogenates were found to vary widely between different tissues and species. The effects of paraquat on lipid peroxidation was also studied. (DC)

  7. Study on mechanism of decreased lipid peroxide by low dose radiation

    International Nuclear Information System (INIS)

    Yamaoka, Kiyonori; Okazoe, Yoko; Akimaru, Kunihiro; Sato, E.F.; Utsumi, Kozo.

    1991-01-01

    We examined the effect of SOD on lipid peroxidation in biomembrane from V.E-deficient rats, in order to study the mechanism of increased SOD activities and decreased lipid peroxide by low dose irradiation. The following results were obtained. i. Active oxygen (O 2 - ) strongly enhances lipid peroxidations in biomembrane with the Fe 3+ as catalyst. ii. SOD evidently inhibits lipid peroxidations under above conditions. iii. We suggested that the effect of SOD enhanced by low dose irradiation results in inhibition of lipid peroxidation. (author)

  8. Concentrations of and application protocols for hydrogen peroxide bleaching gels: effects on pulp cell viability and whitening efficacy.

    Science.gov (United States)

    Soares, Diana Gabriela; Basso, Fernanda Gonçalves; Hebling, Josimeri; de Souza Costa, Carlos Alberto

    2014-02-01

    To assess the whitening effectiveness and the trans-enamel/trans-dentinal toxicity of experimental tooth-bleaching protocols on pulp cells. Enamel/dentine discs individually adapted to trans-well devices were placed on cultured odontoblast-like cells (MDPC-23) or human dental pulp cells (HDPCs). The following groups were formed: G1 - no treatment (control); G2 to G4 - 35% H2O2, 3 × 15, 1 × 15, and 1 × 5 min, respectively; and G5 to G7 - 17.5% H2O2, 3 × 15, 1 × 15, and 1 × 5 min, respectively. Cell viability and morphology were evaluated immediately after bleaching (T1) and 72 h thereafter (T2). Oxidative stress and cell membrane damage were also assessed (T1). The amount of H2O2 in culture medium was quantified (Mann-Whitney; α=5%) and colour change (ΔE) of enamel was analysed after 3 sessions (Tukey's test; α=5%). Cell viability reduction, H2O2 diffusion, cell morphology alteration, oxidative stress, and cell membrane damage occurred in a concentration-/time-dependent fashion. The cell viability reduction was significant in all groups for HDPCs and only for G2, G3, and G5 in MDPC-23 cells compared with G1. Significant cell viability and morphology recovery were observed in all groups at T2, except for G2 in HDPCs. The highest ΔE value was found in G2. However, all groups presented significant ΔE increases compared with G1. Shortening the contact time of a 35%-H2O2 gel for 5 min, or reducing its concentration to 17.5% and applying it for 45, 15, or 5 min produce gradual tooth colour change associated with reduced trans-enamel and trans-dentinal cytotoxicity to pulp cells. The experimental protocols tested in the present study provided significant tooth-bleaching improvement associated with decreased toxicity to pulp cells, which may be an interesting alternative to be tested in clinical situations intended to reduce tooth sensitivity and pulp damage. Copyright © 2013 Elsevier Ltd. All rights reserved.

  9. Mechanisms underlying ectopic persistent tooth-pulp pain following pulpal inflammation.

    Directory of Open Access Journals (Sweden)

    Shingo Matsuura

    Full Text Available In order to clarify the peripheral mechanisms of ectopic persistent pain in a tooth pulp following pulpal inflammation of an adjacent tooth, masseter muscle activity, phosphorylated extracellular signal-regulated protein kinase (pERK and TRPV1 immunohistochemistries and satellite cell activation using glial fibrillary acidic protein (GFAP immunohistochemistry in the trigeminal ganglion (TG were studied in the rats with molar tooth-pulp inflammation. And, Fluorogold (FG and DiI were also used in a neuronal tracing study to analyze if some TG neurons innervate more than one tooth pulp. Complete Freund's adjuvant (CFA or saline was applied into the upper first molar tooth pulp (M1 in pentobarbital-anesthetized rats, and capsaicin was applied into the upper second molar tooth pulp (M2 on day 3 after the CFA or saline application. Mean EMG activity elicited in the masseter muscle by capsaicin application to M2 was significantly larger in M1 CFA-applied rats compared with M1 vehicle-applied rats. The mean number of pERK-immunoreactive (IR TG cells was significantly larger in M1 CFA-applied rats compared with M1 vehicle-applied rats. Application of the satellite cell inhibitor fluorocitrate (FC into TG caused a significant depression of capsaicin-induced masseter muscle activity and a significant reduction of satellite cell activation. The number of TRPV1-IR TG cells innervating M2 was significantly larger in M1 CFA-applied rats compared with M1 vehicle-applied rats, and that was decreased following FC injection into TG. Furthermore, 6% of TG neurons innervating M1 and/or M2 innervated both M1 and M2. These findings suggest that satellite cell activation following tooth pulp inflammation and innervation of multiple tooth pulps by single TG neurons may be involved in the enhancement of the activity of TG neurons innervating adjacent non-inflamed teeth that also show enhancement of TRPV1 expression in TG neurons, resulting in the ectopic persistent tooth-pulp

  10. Membrane lipid peroxidation by UV-A: Mechanism and implications

    International Nuclear Information System (INIS)

    Bose, B.; Agarwal, S.; Chatterjee, S.N.

    1990-01-01

    UV-A produced a dose-dependent linear increase of lipid peroxidation in liposomal membrane, as detected by the assay of (i) conjugated dienes, (ii) lipid hydroperoxides, (iii) malondialdehydes (MDA), and (iv) the fluorescent adducts formed by the reaction of MDA with glycine and also a linear dose-dependent increase of [ 14 C]glucose efflux from the liposomes. UV-A-induced MDA production could not be inhibited by any significant degree by sodium formate, dimethyl sulfoxide, EDTA, or superoxide dismutase but was very significantly inhibited by butylated hydroxytoluene, alpha-tocopherol, sodium azide, L-histidine, dimethylfuran, and beta-carotene. MDA formation increased with an increase in the D 2 O content in water, leading to a maximal amount of nearly 50% enhancement of lipid peroxidation in 100% D 2 O vis-a-vis water used as dispersion medium. The experimental findings indicate the involvement of singlet oxygen as the initiator of the UV-A-induced lipid peroxidation

  11. Mechanical Responses and Physical Factors of the Fingertip Pulp

    Directory of Open Access Journals (Sweden)

    N. Sakai

    2006-01-01

    Full Text Available The images of the mechanical responses were analysed when the fingertip was pressed against a plateau plate, and the influence of the contact angle on the loading pressure and the mechanical responses was investigated. As a result, as the contact angle was smaller, the change ratios due to the loading pressure were significantly larger in the contact length, the contact width and the distortion of lateral-view area. These parameters were thought to be useful in clinical medicine as indices for the degrees of mechanical responses of the fingertip. The length of the central axis and the maximum width of the fingertip were inappropriate as the parameters to represent the mechanical responses of the fingertip. The maximum width of the fingertip scarcely changed. This does not reflect the compressibility of the fingertip, and the fingertip as a whole extended along the central axis and in the vertical direction, and the change was not reflected in the maximum width.

  12. Kinetics and mechanism of the furan peroxide formation in the reaction of furfural with hydrogen peroxide in the presence and absence of sodium molybdate

    International Nuclear Information System (INIS)

    Grunskaya, E.P.; Badovskaya, L.A.; Kaklyugina, T.Ya.; Poskonin, V.V.

    2000-01-01

    Kinetics of the initial stage of the reaction of furfural with hydrogen peroxide are studied in the presence of Na 2 MoO 4 in water and without catalytic additions in n-butanol. Organic peroxide having in its disposal Mo(6), which is the only product on the initial stage of the reaction, is formed since the first minutes of oxidation of furfural by hydrogen peroxide with the presence of Na 2 MoO 4 . The mechanisms of conversion of furfural in the Na 2 MoO 4 - H 2 O system and its oxidation by peroxide without sodium molybdate are discussed. Schemes of formation of furfural complexes based on the results of kinetic studies are suggested. Comparison of obtained data demonstrates that presence of the sodium molybdates in the reaction medium trends to change of reaction procedure in the hydrogen peroxide [ru

  13. SUSTAINABLE PAPER - Biotechnical modification of mechanical pulp. Final report; KESTAeVAe PAPERI - Mekaanisen massan biotekninen muokkaus. Loppuraportti

    Energy Technology Data Exchange (ETDEWEB)

    Pere, J.; Liukkonen, S.; Gullichsen, J.; Viikari, L.

    1997-12-31

    In this work the application of purified enzymes in mechanical pulping was studied. The aim was to gain energy savings in secondary refining of mechanical pulp by modifying pulp fractions with enzymes. One special objective was to increase the flexibility and bonding ability of long fibre fraction. The main interest was in Trichoderma reesei cellulases (CBH I, CBH II, EG I) and hemicellulases (xylanase, mannanase), but a few commercial enzyme preparations (pectinase, cellulase) were also tested. Coarse mechanical pulp (CSF 350-600 ml) or functioned reject (CSF 550-700 ml) were treated with enzymes (45 deg C. pH 5,2-16 h). After enzymatic treatment the pulps were subjected to secondary refining either with a laboratory scale disk refiner (Sprout-Waldron) or a wing defibrator. Some of the results obtained in laboratory scale were further verified in pilot scale. The accessibility of mechanical pulp to enzymatic hydrolysis was limited and therefore yield losses of raw material due to the enzymatic treatments were usually very low, < 0,6 % of original dry weight. The liberation of soluble oligosaccharides was affected by the enzyme used and also depended on the freeness level and metal composition of the pulp. Endoglucanase (EG I) and mannanase solubilized reducing sugars more efficiently than cellobiohydrolases (CBH I, CBH II). If secondary refining was performed with the atmospheric disk refiner no energy savings or improvement in pulp properties were gained with any of the enzymes tested as compared with the untreated reference. But energy savings up to 20-30 % were obtained when the pulp was pretreated with CBH I prior to secondary refining with the wing defibrator. Pretreatment of the pulp with mannanase gave small energy savings (10-20 %), too. Boosting of secondary refining with CBH I and mannanase was attained while retaining good handsheet properties of the pulp. The positive effects of CBH I on secondary refining were further verified in pilot scale. In a two

  14. Mechanism of ascorbic acid interference in biochemical tests that use peroxide and peroxidase to generate chromophore.

    Science.gov (United States)

    Martinello, Flávia; Luiz da Silva, Edson

    2006-11-01

    Ascorbic acid interferes negatively in peroxidase-based tests (Trinder method). However, the precise mechanism remains unclear for tests that use peroxide, a phenolic compound and 4-aminophenazone (4-AP). We determined the chemical mechanism of this interference, by examining the effects of ascorbic acid in the reaction kinetics of the production and reduction of the oxidized chromophore in urate, cholesterol, triglyceride and glucose tests. Reaction of ascorbic acid with the Trinder method constituents was also verified. Ascorbic acid interfered stoichiometrically with all tests studied. However, it had two distinct effects on the reaction rate. In the urate test, ascorbic acid decreased the chromophore formation with no change in its production kinetics. In contrast, in cholesterol, triglyceride and glucose tests, an increase in the lag phase of color development occurred. Of all the Trinder constituents, only peroxide reverted the interference. In addition, ascorbic acid did not interfere with oxidase activity nor reduce significantly the chromophore formed. Peroxide depletion was the predominant chemical mechanism of ascorbic acid interference in the Trinder method with phenolics and 4-AP. Distinctive effects of ascorbic acid on the reaction kinetics of urate, cholesterol, glucose and triglyceride might be due to the rate of peroxide production by oxidases.

  15. BLEACHING EUCALYPTUS PULPS WITH SHORT SEQUENCES

    Directory of Open Access Journals (Sweden)

    Flaviana Reis Milagres

    2011-03-01

    Full Text Available Eucalyptus spp kraft pulp, due to its high content of hexenuronic acids, is quite easy to bleach. Therefore, investigations have been made attempting to decrease the number of stages in the bleaching process in order to minimize capital costs. This study focused on the evaluation of short ECF (Elemental Chlorine Free and TCF (Totally Chlorine Free sequences for bleaching oxygen delignified Eucalyptus spp kraft pulp to 90% ISO brightness: PMoDP (Molybdenum catalyzed acid peroxide, chlorine dioxide and hydrogen peroxide, PMoD/P (Molybdenum catalyzed acid peroxide, chlorine dioxide and hydrogen peroxide, without washing PMoD(PO (Molybdenum catalyzed acid peroxide, chlorine dioxide and pressurized peroxide, D(EPODP (chlorine dioxide, extraction oxidative with oxygen and peroxide, chlorine dioxide and hydrogen peroxide, PMoQ(PO (Molybdenum catalyzed acid peroxide, DTPA and pressurized peroxide, and XPMoQ(PO (Enzyme, molybdenum catalyzed acid peroxide, DTPA and pressurized peroxide. Uncommon pulp treatments, such as molybdenum catalyzed acid peroxide (PMo and xylanase (X bleaching stages, were used. Among the ECF alternatives, the two-stage PMoD/P sequence proved highly cost-effective without affecting pulp quality in relation to the traditional D(EPODP sequence and produced better quality effluent in relation to the reference. However, a four stage sequence, XPMoQ(PO, was required to achieve full brightness using the TCF technology. This sequence was highly cost-effective although it only produced pulp of acceptable quality.

  16. THERMO-MECHANICAL PULPING AS A PRETREATMENT FOR AGRICULTURAL BIOMASS FOR BIOCHEMICAL CONVERSION

    Directory of Open Access Journals (Sweden)

    Ronalds W. Gonzalez

    2011-03-01

    Full Text Available The use of thermo-mechanical pulping (TMP, an existing and well known technology in the pulp and paper industry, is proposed as a potential pretreatment pathway of agriculture biomass for monomeric sugar production in preparation for further fermentation into alcohol species. Three agricultural biomass types, corn stover, wheat straw, and sweet sorghum bagasse, were pretreated in a TMP unit under two temperature conditions, 160 ºC and 170 ºC, and hydrolyzed using cellulase at 5, 10, and 20 FPU/g OD biomass. Wheat straw biomass was further pretreated at different conditions including: i soaking with acetic acid, ii longer steaming residence time (15 and 30 min, and iii refined at lower disk gap (0.0508 and 0.1524 mm. Preliminary results showed that carbohydrate conversion increased from 25% to 40% when the TMP temperature was increased from 160 to 170 ºC. Carbohydrate conversion was relatively similar for the three biomasses under the same pretreatment conditions and enzyme loading. Acetic acid soaking and refining at a reduce disk gap increases carbohydrate conversion. Further studies within this technological field to identify optimum process and TMP conditions for pretreatment are suggested.

  17. Antibacterial Properties and Mechanism of Activity of a Novel Silver-Stabilized Hydrogen Peroxide.

    Directory of Open Access Journals (Sweden)

    Nancy L Martin

    Full Text Available Huwa-San peroxide (hydrogen peroxide; HSP is a NSF Standard 60 (maximum 8 mg/L(-1 new generation peroxide stabilized with ionic silver suitable for continuous disinfection of potable water. Experiments were undertaken to examine the mechanism of HSP against planktonic and biofilm cultures of indicator bacterial strains. Contact/kill time (CT relationships that achieve effective control were explored to determine the potential utility in primary disinfection. Inhibitory assays were conducted using both nutrient rich media and a medium based on synthetic wastewater. Assays were compared for exposures to three disinfectants (HSP, laboratory grade hydrogen peroxide (HP and sodium hypochlorite at concentrations of 20 ppm (therefore at 2.5 and 5 times the NSF limit for HP and sodium hypochlorite, respectively and at pH 7.0 and 8.5 in dechlorinated tap water. HSP was found to be more or equally effective as hypochlorite or HP. Results from CT assays comparing HSP and HP at different bacterial concentrations with neutralization of residual peroxide with catalase suggested that at a high bacterial concentration HSP, but not HP, was protected from catalase degradation possibly through sequestration by bacterial cells. Consistent with this hypothesis, at a low bacterial cell density residual HSP was more effectively neutralized as less HSP was associated with bacteria and therefore accessible to catalase. Silver in HSP may facilitate this association through electrostatic interactions at the cell surface. This was supported by experiments where the addition of mono (K(+ and divalent (Ca(+2 cations (0.005-0.05M reduced the killing efficacy of HSP but not HP. Experiments designed to distinguish any inhibitory effect of silver from that of peroxide in HSP were carried out by monitoring the metabolic activity of established P. aeruginosa PAO1 biofilms. Concentrations of 70-500 ppm HSP had a pronounced effect on metabolic activity while the equivalent

  18. Understanding the mechanism of DNA deactivation in ion therapy of cancer cells: hydrogen peroxide action*

    Science.gov (United States)

    Piatnytskyi, Dmytro V.; Zdorevskyi, Oleksiy O.; Perepelytsya, Sergiy M.; Volkov, Sergey N.

    2015-11-01

    Changes in the medium of biological cells under ion beam irradiation has been considered as a possible cause of cell function disruption in the living body. The interaction of hydrogen peroxide, a long-lived molecular product of water radiolysis, with active sites of DNA macromolecule was studied, and the formation of stable DNA-peroxide complexes was considered. The phosphate groups of the macromolecule backbone were picked out among the atomic groups of DNA double helix as a probable target for interaction with hydrogen peroxide molecules. Complexes consisting of combinations including: the DNA phosphate group, H2O2 and H2O molecules, and Na+ counterion, were considered. The counterions have been taken into consideration insofar as under the natural conditions they neutralise DNA sugar-phosphate backbone. The energy of the complexes have been determined by considering the electrostatic and the Van der Waals interactions within the framework of atom-atom potential functions. As a result, the stability of various configurations of molecular complexes was estimated. It was shown that DNA phosphate groups and counterions can form stable complexes with hydrogen peroxide molecules, which are as stable as the complexes with water molecules. It has been demonstrated that the formation of stable complexes of H2O2-Na+-PO4- may be detected experimentally by observing specific vibrations in the low-frequency Raman spectra. The interaction of H2O2 molecule with phosphate group of the double helix backbone can disrupt DNA biological function and induce the deactivation of the cell genetic apparatus. Thus, the production of hydrogen peroxide molecules in the nucleus of living cells can be considered as an additional mechanism by which high-energy ion beams destroy tumour cells during ion beam therapy. Contribution to the Topical Issue "COST Action Nano-IBCT: Nano-scale Processes Behind Ion-Beam Cancer Therapy", edited by Andrey Solov'yov, Nigel Mason, Gustavo García, Eugene

  19. PROCESS OPTIMIZATION OF TETRA ACETYL ETHYLENE DIAMINE ACTIVATED HYDROGEN PEROXIDE BLEACHING OF POPULUS NIGRA CTMP

    OpenAIRE

    Qiang Zhao; Junwen Pu; Shulei Mao; Guibo Qi

    2010-01-01

    To enhance the bleaching efficiency, the activator of tetra acetyl ethylene diamine (TAED) was used in conventional H2O2 bleaching. The H2O2/TAED bleaching system can accelerate the reaction rate and shorten bleaching time at relative low temperature, which can reduce the production cost. In this research, the process with hydrogen peroxide activated by TAED bleaching of Populus nigra chemi-thermo mechanical pulp was optimized. Suitable bleaching conditions were confirmed as follows: pulp con...

  20. China’s High-yield Pulp Sector and Its Carbon Dioxide Emission: Considering the Saved Standing Wood as an Increase of Carbon Storage

    Directory of Open Access Journals (Sweden)

    Yanhong Gao

    2014-11-01

    Full Text Available The production of high-yield pulp in China has increased significantly in recent years. The well-known advantages of this type of pulp include low production cost, high opacity, and good paper formation. In the context of state-of-the-art technologies, China’s high-yield pulping, which is dominated by the PRC-APMP (preconditioning refiner chemical treatment-alkaline peroxide mechanical pulping process, has a much higher energy input but a significantly lower wood consumption in comparison with the kraft pulping process. If the saved wood in the forest or plantation is considered as an increment of carbon storage, then the carbon dioxide emission from the production of high-yield pulp can be regarded as much lower than that of kraft pulp.

  1. Mechanical and Thermal Properties of Bamboo Pulp Fiber Reinforced Polyethylene Composites

    Directory of Open Access Journals (Sweden)

    Wenhan Ren

    2014-05-01

    Full Text Available The purpose of this study was to investigate the mechanical and thermal properties of high-density polyethylene (HDPE composites reinforced by bamboo pulp fibers (BPF. Using a twin-screw extruder, polymer composites were fabricated using BPF and bamboo flour (BF as the reinforcement and HDPE as the matrix. Tensile and flexural tests of the HDPE composites were performed to determine the mechanical properties under different conditions. The thermal properties of HDPE composites were characterized by thermogravimetric analysis (TGA and dynamic mechanical analysis (DMA. The results showed that BPF improved the mechanical and thermal properties of the polymer composites more than did BF. The tensile and flexural strength of composites with 30 wt% BPF were increased by 61.46% and 22.94%, respectively, while the tensile and flexural modulus were increased by 84.52% and 27.30%, respectively. Compared to composites with 50 wt% BF, the T5% of composites with 50 wt% BPF increased by 20.18 °C. As the BPF content increased, the storage modulus (E’ and loss modulus (E” initially increased, followed by a decrease. Compared to the BF/HDPE composites, BPF/HDPE composites reinforced at 30 wt% had a higher storage modulus (E’ and loss modulus (E” and lower damping parameter (tanδ.

  2. STUDIES ON THE INITIATION MECHANISM OF ORGANIC PEROXIDE AND N-METHACRYLOYLOXYETHYL-N-METHYL ANILINE IN METHYL METHACRYLATE POLYMERIZATION

    Institute of Scientific and Technical Information of China (English)

    QIU Kunyuan; GUO Dajie; GUO Xinqiu; FENG Xinde

    1990-01-01

    The initiation mechanism of methyl methacrylate (MMA) polymerization by organic peroxide and polymerizable aromatic tertiary amine such as N-methacryloyloxyethyl-N-methyi aniline (MEMA) binary system has been studied. The kinetics of polymerization of MMA and the ESR spectra of organic peroxide/MEMA system were determined. Based on the ESR study and the end-group analysis by UV spectra of the polymer formed, the initiation mechanism is proposed.

  3. In-office tooth bleaching with 38% hydrogen peroxide promotes moderate/severe pulp inflammation and production of ll-1β, TNF-β, GPX, FGF-2 and osteocalcin in rats.

    Science.gov (United States)

    Silva-Costa, Renata Suellen Galvão da; Ribeiro, Andressa Eveline de Lima; Assunção, Isauremi Vieira de; Araújo Júnior, Raimundo Fernandes de; Araújo, Aurigena Antunes de; Guerra, Gerlane Coelho Bernardo; Borges, Boniek Castillo Dutra

    2018-06-11

    To study the intensity of inflammatory infiltrate and production of interleukin-1β (ll-1β), tumor necrosis factor-β (TNF-β), fibroblast growth factor-2 (FGF-2), glutathione peroxidase (GPX), and osteocalcin in response to in-office tooth bleaching in rats. Twenty male Wistar rats were randomized into four groups (n=5) according to the received treatment (tooth bleaching or no treatment - control) and the period of euthanasia after treatment (24 h or 10 days). We performed tooth bleaching using a 38% hydrogen peroxide gel on maxillary and mandibular incisors. After euthanasia, incisors (20 per group) were processed for histological analysis, immunohistochemistry staining of ll-1β, TNF-β, FGF-2 and GPX and osteocalcin by immunofluorescence. We analyzed data using the Mann-Whitney and Kruskal-Wallis/Dunn tests (p<0.05). The bleached groups presented statistically significant differences regarding the pulp inflammation stage compared with the control groups. Bleached teeth showed moderate/severe inflammatory infiltrate and control groups presented absent inflammatory cells or a negligible number of mononuclear cells (p<0.001) at two times (24 h and 10 days). There was strong staining for ll-1β, TNF-β, and GPX in bleached groups at 24 h and strong staining for ll-1β, TNF-β, GPX and FGF-2 at 10 days. After 10 days of tooth bleaching, the bleached group showed a statistically superior amount of osteocalcin than the other groups (p<0.01). Tooth bleaching with 38% hydrogen peroxide causes severe pulp inflammation, but characteristics of tissue repair after 10 days.

  4. In-office tooth bleaching with 38% hydrogen peroxide promotes moderate/severe pulp inflammation and production of ll-1β, TNF-β, GPX, FGF-2 and osteocalcin in rats

    Directory of Open Access Journals (Sweden)

    Renata Suellen Galvão da Silva-Costa

    2018-06-01

    Full Text Available Abstract Objectives: To study the intensity of inflammatory infiltrate and production of interleukin-1β (ll-1β, tumor necrosis factor-β (TNF-β, fibroblast growth factor-2 (FGF-2, glutathione peroxidase (GPX, and osteocalcin in response to in-office tooth bleaching in rats. Material and Methods: Twenty male Wistar rats were randomized into four groups (n=5 according to the received treatment (tooth bleaching or no treatment - control and the period of euthanasia after treatment (24 h or 10 days. We performed tooth bleaching using a 38% hydrogen peroxide gel on maxillary and mandibular incisors. After euthanasia, incisors (20 per group were processed for histological analysis, immunohistochemistry staining of ll-1β, TNF-β, FGF-2 and GPX and osteocalcin by immunofluorescence. We analyzed data using the Mann-Whitney and Kruskal-Wallis/Dunn tests (p<0.05. Results: The bleached groups presented statistically significant differences regarding the pulp inflammation stage compared with the control groups. Bleached teeth showed moderate/severe inflammatory infiltrate and control groups presented absent inflammatory cells or a negligible number of mononuclear cells (p<0.001 at two times (24 h and 10 days. There was strong staining for ll-1β, TNF-β, and GPX in bleached groups at 24 h and strong staining for ll-1β, TNF-β, GPX and FGF-2 at 10 days. After 10 days of tooth bleaching, the bleached group showed a statistically superior amount of osteocalcin than the other groups (p<0.01. Conclusions: Tooth bleaching with 38% hydrogen peroxide causes severe pulp inflammation, but characteristics of tissue repair after 10 days.

  5. [Participation of final products of lipid peroxidation in the anticancer mechanism of ionizing radiation and radiomimetic cytostatics].

    Science.gov (United States)

    Przybyszewski, W M

    2001-01-01

    This review reports the evidence for the participation of final products of lipid peroxidation in the anticancer mechanism of ionising radiation and radiomimetic cytostatics. Processes of lipid peroxidation occur endogenously in response to oxidative stress and great diversity of reactive metabolites is formed. However, direct observation of radical reaction in pathophysiology of cells, tissues and organs is limited technically. Most investigations focused on the indirect assessment of their final products, aldehydes. The peroxidative breakdown of polyunsaturated fatty acids is believed to be involved in the regulation of cell division, and antitumor effect through biochemical and genetic processes.

  6. Protective mechanisms against peptide and protein peroxides generated by singlet oxygen

    DEFF Research Database (Denmark)

    Morgan, Philip E; Dean, Roger T; Davies, Michael Jonathan

    2004-01-01

    or detoxify such peroxides. It is shown that catalase, horseradish peroxidase, and Cu/Zn superoxide dismutase do not react rapidly with these peroxides. Oxymyoglobin and oxyhemoglobin, but not the met (Fe3+) forms of these proteins, react with peptide but not protein, peroxides with oxidation of the heme iron...

  7. Effect of Soda-Anthraquinone Pulping Conditions and Beating Revolution on the Mechanical Properties of Paper made from Gigantochloa scortechinii (Semantan Bamboo)

    International Nuclear Information System (INIS)

    Nurul Husna Mohd Hassan; Suhaimi Muhammed

    2013-01-01

    The effect of soda-AQ pulping conditions and beating revolution on the mechanical properties of paper made from Semantan bamboo (Gigantochloa scortechinii) was studied. The bamboo chips were pulped using MK digester pulping unit with 10 to 20 % alkali charge and 150 to 170 degree Celsius cooking temperature. The screened yield varies from 38.7 to 48.4 %, and each yield went through beating process at 1000 or 8000 beating revolutions. The bamboo pulp was then made into 60 g/ m 2 laboratory scale papers and their mechanical properties were assessed conforming to TAPPI standards. The results revealed that tensile index, bursting index, tearing index and folding endurance ranged from 42.04 to 91.09 Nm/ g, 2.68 to 7.10 kPa.m 2 /g, 11.03 to 26.64 mN.m 2 /g and 30 to 1127 double folds, respectively. The highest paper properties were found from pulping condition of 15 % alkali charge and 150 degree Celsius cooking temperature based on the fibre bonding index, with tensile index at 87.71 Nm/g, bursting index at 6.94 kPa.m 2 / g, tearing index at 12.72 mN.m 2 / g and folding endurance at 613 double folds. Such findings indicate that comparable high strength mechanical properties of paper can be produced from Semantan bamboo pulp with more environmentally friendly pulping process compared to the kraft pulping process that had been used in bamboo pulping. (author)

  8. Superoxide anions and hydrogen peroxide induce hepatocyte death by different mechanisms : Involvement of JNK and ERK MAP kinases

    NARCIS (Netherlands)

    Conde de la Rosa, L; Schoemaker, MH; Vrenken, TE; Buist-Homan, M; Havinga, R; Jansen, PLM; Moshage, H

    Background/Aims: In liver diseases, reactive oxygen species (ROS) are involved in cell death and liver injury, but the mechanisms are not completely elucidated. To elucidate the mechanisms of hepatocyte cell death induced by the ROS superoxide anions and hydrogen peroxide, primary cultures of

  9. Superoxide anions and hydrogen peroxide induce hepatocyte death by different mechanisms: involvement of JNK and ERK MAP kinases

    NARCIS (Netherlands)

    Conde de la Rosa, Laura; Schoemaker, Marieke H.; Vrenken, Titia E.; Buist-Homan, Manon; Havinga, Rick; Jansen, Peter L. M.; Moshage, Han

    2006-01-01

    BACKGROUND/AIMS: In liver diseases, reactive oxygen species (ROS) are involved in cell death and liver injury, but the mechanisms are not completely elucidated. To elucidate the mechanisms of hepatocyte cell death induced by the ROS superoxide anions and hydrogen peroxide, primary cultures of

  10. Determination of The Optimum Use of Cationic Starch on the Basis of the Mechanical Strengths of Mixed OCC and Virgin NSSC pulps

    Directory of Open Access Journals (Sweden)

    Mansour Ghaffari

    2012-01-01

    Full Text Available This study was carried out to optimize of cationic starch use for improvement of the mechanical properties of mixed OCC & NSSC pulps. NSSC pulps were mixed with the OCC pulps by following weight ratios: 80/20, 70/30 and 60/40, respectively. Cationic starch was used in different charges of 0.5, 1.25, 2 and 3 %. The produced paper strength properties were measured according to Tappi standard. The results obtained from normalized equation showed that treatment of C4 (60% NSSC+ 40% OCC using 3% Cationic starch is the best suitable samples. Also, by increasing the OCC proportion in mixed pulps, tensile, Tear, burst strengths increases, but Concora medium test (CMT and Ring crush test (RCT decreased. In general, by increasing of the cationic starch dosage, mechanical strengths has increased and its improved use had determined by 3% cationic starch.

  11. Morphological development of cellulose fibrils of a bleached eucalyptus pulp by mechanical fibrillation

    Science.gov (United States)

    Q.Q. Wang; J.Y. Zhu; R. Gleisner; T.A. Kuster; U. Baxa; S.E. McNeil

    2012-01-01

    This study reports the production of cellulose nanofibrils (CNF) from a bleached eucalyptus pulp using a commercial stone grinder. Scanning electronic microscopy and transmission electronic microscopy imaging were used to reveal morphological development of CNF at micro and nano scales, respectively. Two major structures were identified (1) highly kinked, naturally...

  12. Evaluating chemical-, mechanical-, and bio-pulping processes and their sustainability characterization using life cycle assessment

    Science.gov (United States)

    Tapas K. Das; Carl Houtman

    2004-01-01

    Pulp and paper manufacturing constitutes one of the largest industry segments in the United States in term of water and energy usage and total discharges to the environment. More than many other industries, however, this industry plays an important role in sustainable development because its chief raw material— wood fiber—is renewable. This industry provides an example...

  13. Mechanism of Sporicidal Activity for the Synergistic Combination of Peracetic Acid and Hydrogen Peroxide.

    Science.gov (United States)

    Leggett, Mark J; Schwarz, J Spencer; Burke, Peter A; McDonnell, Gerald; Denyer, Stephen P; Maillard, Jean-Yves

    2016-02-15

    There is still great interest in controlling bacterial endospores. The use of chemical disinfectants and, notably, oxidizing agents to sterilize medical devices is increasing. With this in mind, hydrogen peroxide (H2O2) and peracetic acid (PAA) have been used in combination, but until now there has been no explanation for the observed increase in sporicidal activity. This study provides information on the mechanism of synergistic interaction of PAA and H2O2 against bacterial spores. We performed investigations of the efficacies of different combinations, including pretreatments with the two oxidizers, against wild-type spores and a range of spore mutants deficient in the spore coat or small acid-soluble spore proteins. The concentrations of the two biocides were also measured in the reaction vessels, enabling the assessment of any shift from H2O2 to PAA formation. This study confirmed the synergistic activity of the combination of H2O2 and PAA. However, we observed that the sporicidal activity of the combination is largely due to PAA and not H2O2. Furthermore, we observed that the synergistic combination was based on H2O2 compromising the spore coat, which was the main spore resistance factor, likely allowing better penetration of PAA and resulting in the increased sporicidal activity. Copyright © 2016 Leggett et al.

  14. Coupling mechanism between wear and oxidation processes of 304 stainless steel in hydrogen peroxide environments.

    Science.gov (United States)

    Dong, Conglin; Yuan, Chengqing; Bai, Xiuqin; Li, Jian; Qin, Honglin; Yan, Xinping

    2017-05-24

    Stainless steel is widely used in strongly oxidizing hydrogen peroxide (H 2 O 2 ) environments. It is crucial to study its wear behaviour and failure mode. The tribological properties and oxidation of 304 stainless steel were investigated using a MMW-1 tribo-tester with a three-electrode setup in H 2 O 2 solutions with different concentrations. Corrosion current densities (CCDs), coefficients of frictions (COFs), wear mass losses, wear surface topographies, and metal oxide films were analysed and compared. The results show that the wear process and oxidation process interacted significantly with each other. Increasing the concentration of H 2 O 2 or the oxidation time was useful to form a layer of integrated, homogeneous, compact and thick metal oxide film. The dense metal oxide films with higher mechanical strengths improved the wear process and also reduced the oxidation reaction. The wear process removed the metal oxide films to increase the oxidation reaction. Theoretical data is provided for the rational design and application of friction pairs in oxidation corrosion conditions.

  15. Peroxide organometallic compounds and their transformations

    International Nuclear Information System (INIS)

    Razuvaev, G.A.; Brilkina, T.G.

    1976-01-01

    A survey is given experimental works on synthesis and reactions of peroxide organometallic compounds. Reactions have been considered of organometallic compounds with oxygen and organic peroxides which result in formation of both peroxide and non-peroxide products. Possible routes and mechanisms of chemical transformations of peroxide organometallic compounds have been discussed. Reactions of organometallic compounds with oxygen and peroxides have been considered

  16. Ageing mechanisms in chickpea seeds: Relationship of sugar hydrolysis and lipid peroxidation with Amadori and Millard reactions

    Directory of Open Access Journals (Sweden)

    mahdi shaaban

    2017-05-01

    Full Text Available This experiment was performed in order to study on ageing mechanisms of chickpea seeds (Cicer arietinum L. in natural storage and accelerated ageing conditions in seed laboratory of Gorgan Agricultural Science and Natural Resources, Gorgan, Iran at 2015. Experiment was in completely randomized design arrangement with four replications. Treatments were 2 and 4 years natural storage and 1-5 days of accelerated ageing with control treatment. The results showed that with increasing of natural storage and accelerated ageing duration, germination percentage was decreased. Increasing of ageing duration decreased soluble sugars, non-reducing sugars and soluble proteins but lipid peroxidation, reducing sugars, protein carbonylation and Amadori and Millard reaction were increased. In natural storage condition lipid peroxidation was more than sugar hydrolysis but in accelerated ageing condition sugar hydrolysis was more than lipid peroxidation. These results show that the main reason of Amadori and Millard reaction in chickpea seeds in natural storage condition is lipid peroxidation and in accelerated ageing condition is sugar hydrolysis. Also, the results showed that Amadori reaction in natural storage condition was more than Amadori reaction and in accelerated ageing condition Millard reaction was more than Amadori reaction. The results of the present study showed that sever Millard reaction after Amadori reaction induced higher damage on seed and results to more decrease of seed viability and reduce of seed germination percentage in accelerated ageing than natural storage.

  17. Improved diffusivity of NaOH solution in autohydrolyzed poplar sapwood chips for chemi-mechanical pulp production.

    Science.gov (United States)

    Zhang, Honglei; Hou, Qingxi; Liu, Wei; Yue, Zhen; Jiang, Xiaoya; Ma, Xixi

    2018-07-01

    This work investigated the changes in the physical structure of autohydrolyzed poplar sapwood chips and the effect on the subsequent alkali liquor diffusion properties for chemi-mechanical pulping (CMP). An alkali impregnation process was conducted by using the autohydrolyzed poplar sapwood with different levels of autohydrolysis intensity. The results showed that the volume porosity, water constraint capacity, and saturated water absorption of the autohydrolyzed poplar sapwood chips increased. Also, the effective capillary cross-sectional area (ECCSA) in the radial direction and the diffusion coefficients of NaOH solution in both the radial and axial directions all increased. Autohydrolysis pretreatment enhanced the alkali liquor diffusion properties in poplar sapwood chips, and the diffusion coefficient was increased more greatly in the radial direction than that in the axial direction. Copyright © 2018 Elsevier Ltd. All rights reserved.

  18. Reduction of lipophilic extractives in mechanical pulps; Mekaanisen massan uuteainepitoisuuden alentaminen - EKT 07

    Energy Technology Data Exchange (ETDEWEB)

    Edelmann, K [VTT Energy, Jyvaeskylae (Finland)

    1999-12-31

    Adsorption of lipophilic extractives released from wood to various filtrates and pressed fractions in the production of thermomechanical pulp on various inorganic substrates has been studied. Both commercial and experimental adsorbents were used. Equilibrium concentrations of lipophilic extractives were determined. Best adsorption results were achieved with talcum and cationized kaolin. Adsorption behaviour of Al2O3 granulate was varied with respect to surface charge and surface energy. In addition to adsorption, oxidation of lipophilic extractives through ozonation and cavitation was studied. In the oxidation studies also other compounds than lipophilic extractives should be followed in order to determine the chemical changes of the process water. The adsorption process is economically more feasible, if the concentration of lipophilic extractives were four to five times higher than the present value 50 mg/l. However more work has to be directed to the development of production methods of the adsorbent itself. Dynamics of the adsorption process should closely be studied. Combined adsorption and ozonation especially in the presence of an oxidation catalyst might be an interesting topic for further studies. (orig.)

  19. Reduction of lipophilic extractives in mechanical pulps; Mekaanisen massan uuteainepitoisuuden alentaminen - EKT 07

    Energy Technology Data Exchange (ETDEWEB)

    Edelmann, K. [VTT Energy, Jyvaeskylae (Finland)

    1998-12-31

    Adsorption of lipophilic extractives released from wood to various filtrates and pressed fractions in the production of thermomechanical pulp on various inorganic substrates has been studied. Both commercial and experimental adsorbents were used. Equilibrium concentrations of lipophilic extractives were determined. Best adsorption results were achieved with talcum and cationized kaolin. Adsorption behaviour of Al2O3 granulate was varied with respect to surface charge and surface energy. In addition to adsorption, oxidation of lipophilic extractives through ozonation and cavitation was studied. In the oxidation studies also other compounds than lipophilic extractives should be followed in order to determine the chemical changes of the process water. The adsorption process is economically more feasible, if the concentration of lipophilic extractives were four to five times higher than the present value 50 mg/l. However more work has to be directed to the development of production methods of the adsorbent itself. Dynamics of the adsorption process should closely be studied. Combined adsorption and ozonation especially in the presence of an oxidation catalyst might be an interesting topic for further studies. (orig.)

  20. A kinetic analysis of the changes in infra-red spectra of mechanical pulps during irradiation

    International Nuclear Information System (INIS)

    Kimura, F.; Kimura, T.; Gray, D.G.

    1995-01-01

    Photo-induced colour rever s ion of unbleached thermomechanical pulp under UV irradiation at 320 nm was studied by FT-IR transmission spectroscopy. The changes of peak heights against the irradiation time were analyzed assuming concurrent first-order reaction processes with slow and fast reaction rates, where r s and r F are slow and fast reaction rates, respectively. The values of r s were larger for peaks due to lignin than for peaks due to carbohydrates (cellulose and hemicellulose), and the slow process predominates for both lignin and carbohydrate peaks. Carbohydrate CH bonds decreased more quickly than CO bonds in carbohydrates during irradiation; r s for the peak assignable to carbohydrate sugar ring stretching is very small. Three newly generated peaks at 2981, 1723, and 1190 cm -1 are attributed to lignin break-down products: they are assignable to CH 2 symmetric (in >CH = CH 2 ) or CH 3 asymmetric stretching vibrations, to non-conjugated carbonyl vibrations, and to C-O stretching of free phenol units, respectively. Weight loss of the sample was observed during irradiation. (author)

  1. Kinetics and mechanism of the oxidation of alkenes and silanes by hydrogen peroxide catalyzed by methylrhenium trioxide (MTO) and a novel application of electrospray mass spectrometry to study the hydrolysis of MTO

    Energy Technology Data Exchange (ETDEWEB)

    Tan, Haisong [Iowa State Univ., Ames, IA (United States)

    1999-11-08

    Conjugated dienes were oxidized by hydrogen peroxide with methylrhenium trioxide (MTO) as catalyst. Methylrhenium bis-peroxide was the major reactive catalyst present. Hydroxyalkenes and trisubstituted silane were also tested. Mechanisms for each of these reactions are presented.

  2. Eucalyptus kraft pulp production: Thermogravimetry monitoring

    International Nuclear Information System (INIS)

    Barneto, Agustin G.; Vila, Carlos; Ariza, Jose

    2011-01-01

    Highlights: → Thermogravimetric analysis can be used to monitor the pulping process in a pulp mill. → ECF bleaching process affects the crystalline cellulose volatilization. → The fibre size has an influence on composition and thermal behavior of pulp. - Abstract: Under oxidative environment the thermal degradation of lignocellulosic materials like wood or pulp is sensitive to slight composition changes. For this, in order to complement the chemical and X-ray diffraction results, thermogravimetric analyses (TGA) were used to monitor pulp production in a modern pulp mill. Runs were carried out on crude, oxygen delignified and bleached pulps from three eucalyptus woods from different species and geographical origins. Moreover, with the modeling of thermogravimetric data, it was possible to obtain an approximate composition of samples which includes crystalline and amorphous cellulose. TGA results show that pulping has an intensive effect on bulk lignin and hemicellulose, but it has limited influence on the removal of these substances when they are linked to cellulose microfibril. The stages of oxygen delignification and bleaching, based in chlorine dioxide and hydrogen peroxide, increase the crystalline cellulose volatilization rate. These changes are compatible with a more crystalline microfibril. The influence of the fibre size on pulp composition, crystallinity and thermal degradation behavior was observed.

  3. Mechanisms of DNA damage by the tumor promoter and progressor benzoyl peroxide

    International Nuclear Information System (INIS)

    Swauger, J.E.; Dolan, P.M.; Zweier, J.L.; Kensler, T.W.

    1990-01-01

    Benzoyl peroxide (BzPO), a tumor promoter and progressor in mouse skin, produces strand breaks in DNA of exposed cells. Previously we have reported that the metabolism of BzPO in keratinocytes proceeds via the initial cleavage of the peroxide bond, yielding benzoyloxyl radicals which, in turn, can fragment to form phenyl radicals and carbon dioxide. Benzoic acid, the product of hydrogen abstraction by the benzoyloxyl radical, is the major stable metabolite of BzPO produced by keratinocytes. In the present study we have examined the capacity of BzPO to generate strand scissions in φX-174 plasmid DNA. DNA damage was dose-dependent over a concentration range of 10-1000 μM BzPO and was dependent on the presence of copper but not other transition state metals. By contrast, benzoic acid did not produce DNA damage in this system. The inclusion of spin trapping agents (PBN, DBNBS), radical scavenging agents (Nal, GSH), or the copper chelator o-phenanthroline in incubations was found to significantly reduce the extent of DNA damage. Electron paramagnetic resonance spectroscopy studies suggested that the primary radical trapped was the benzoyloxyl radical, implying a role for this radical in the generation of the observed DNA damage. Collectively these observations suggest BzPO may be activated to DNA damaging intermediates in keratinocytes via metal-catalyzed cleavage of the peroxide bond resulting in the formation of the benzoyloxyl radical. Covalent modification of DNA was not observed when [ 14 C]BzPO was incubated with calf thymus DNA in the presence of copper. Overall, these results suggest that BzPO induces DNA damage via benzoyloxyl radical mediated proton abstraction from the DNA strand and the adduct formation with DNA is unlikely to occur

  4. The influence of the extraction parameters on the quality of dried sugar beet pulp

    Directory of Open Access Journals (Sweden)

    Bogdanović Branislav V.

    2013-01-01

    Full Text Available Growing demand for better quality and cheaper products put on the need to industry to balance between the two kinds of needs, which are the reduction of production costs and to ensure a high quality product. This is the case with dried sugar beet pulp as a byproduct of sugar refining process. One of the possibilities to reduce energy consumption is savings in the process of thermal dehydration in the process of the conventional drying of pulp. Pulp drying is one third of total energy consumption in the sugar factory. Acidification of water extraction result in pulp that could be pressed better and in other hand in the juice with less non-sucrose compounds. Keeping the extraction process under certain conditions, directly affects on the quality of the extracted pulp and on effects of their further processing. This paper examines the impact of the extraction parameters of sugar from sugar beet and agents of acidification for water extraction (sulphurous acid, hydrogen peroxide on the quality of dried sugar beet pulp. Extraction of sugar from sugar beet cossettes by hydrogen peroxide at pH 5.5 to 8.5 does not cause changes in mechanical properties of sugar beet cossettes and in water retention coefficient, but increases the brightness of dried sugar beet pulp for about 5-7 units, which solubility in water does not depend on the applied concentration of extracting agents, but increases in dependence on the duration of the extraction. Sugar beet pulp extracted at pH 11.0 has reduced strength, they are highly hydrated, and under the force they lose their shape, binding a larger amount of water thus reducing the effect of their pressing. The changes in microstructure were probably accompanied by segmenting the linear parts of macromolecules and are reflected in the increase of water retention capacity and increase the solubility of dried sugar beet pulp for two to three times. Under the same conditions of extraction, sulphurous acid produces similar

  5. Human Dental Pulp-Derived Cells Produce Bone-Like Tissue and Exhibit Bone Cell-Like Responsiveness to Mechanical Loading

    DEFF Research Database (Denmark)

    Kraft, David Christian Evar; Melsen, Birte; Bindslev, Dorthe Arenholt

    2010-01-01

    and characterize cell lines from human 3rd molar dental pulp tissue to determine whether human dental pulp-derived cells (DPCs) are osteogenic and responsive to mechanical loading by pulsating fluid flow (PFF) in vitro. Methods: Human DPCs used for this study were characterized by measuring proliferation....... We also assessed bone formation by DPCs on hydroxyapatite-tricalcium phosphate granules after subcutaneous implantation in mice. Results: We found that DPCs are intrinsically mechanosensitive and, like osteogenic cells, respond to PFF-induced fluid shear stress. Implantation of DPCs resulted...... remodeling in vivo, and therefore provide a promising new tool for regenerative dentistry, for example mineralized tissue engineering to restore bone defects in relation to periodontitis, periimplantatis and orofacial surgery. Experiments in progress have proven that DPCSs are also useful for assessing...

  6. Alkaline pulping of some eucalypts from Sudan.

    Science.gov (United States)

    Khristova, P; Kordsachia, O; Patt, R; Dafaalla, S

    2006-03-01

    Four eucalypts (Eucalyptus camaldulensis, Eucalyptus microtheca, Eucalyptus tereticornis and Eucalyptus citriodora) grown in Sudan were examined for their suitability for pulping and papermaking with different alkaline methods. Their physical, morphological and chemical characteristics are reported. The pulping trials with E. citriodora and E. tereticornis were carried out using the kraft-AQ, soda-AQ, modified AS/AQ (ASA), ASAM and kraft methods. For the other two species, only the ASAM and the kraft process were applied. ASAM pulping gave the best results in terms of yield, degree of delignification, mechanical and optical pulp properties. The best pulps, obtained in kraft and ASAM cooking of E. citriodora, were bleached to 88% ISO brightness in a totally chlorine free bleaching sequence (OQ1O/PQ2P). The bleached pulps, especially the ASAM pulp, showed good papermaking properties and would be suitable for manufacture of writing and printing grades of paper.

  7. The role of bound chlorine in the brightness reversion of bleached hardwood kraft pulp

    Directory of Open Access Journals (Sweden)

    Kátia Maria Morais Eiras

    2009-01-01

    Full Text Available Our previous paper showed fragmentary evidence that pulp brightness reversion may be negatively affected by its organically bound chlorine (OX content. A thorough investigation on eucalyptus kraft pulp led to the conclusion that OX increases reversion of certain pulps but this trend is not universal. Alkaline bleaching stages decrease reversion regardless of pulp OX content. Pulps bleached with high temperature chlorine dioxide revert less than those bleached with conventional chlorine dioxide in sequences ending with a chlorine dioxide stage but similarly in sequences ending with a final peroxide stage. The use of secondary condensate for pulp washing decreases reversion.

  8. The Effect of Wood Alignment on Wood Grinding – Part 1: Properties of Pulp and Fines Revealed in the Grinding Mechanism

    Directory of Open Access Journals (Sweden)

    Erkki Tapani Saharinen

    2016-03-01

    Full Text Available In industrial wood grinding, logs are pressed against a rotating stone, with the logs and fiber axis parallel to the axis of the stone. The objective of this study is to clarify how the wood alignment affects the process and pulp properties. In this research, wood blocks were fed into a laboratory grinder with various alignments in relation to the surface of the grinding stone. The effects of the alignment on the properties of the pulp and the amount and quality of fines were measured. A grinding mechanism was proposed. The results show that the pulp quality is very sensitive to the angle between the stone surface and the log. In gentle refining, the fiber structure is loosened by fatigue before it is bent on the surface; pressure pulses produce fibrillar material, and fibers develop toward having good bonding ability. In forced grinding, the process is “violent”, and the fiber wears and becomes crushed immediately on the surface into small particles with low bonding ability.

  9. Physical and Mechanical Properties of Cellulose Nanofibril Films from Bleached Eucalyptus Pulp by Endoglucanase Treatment and Microfluidization

    Science.gov (United States)

    Wangxia Wang; Ronald C. Sabo; Michael D. Mozuch; Phil Kersten; J. Y. Zhu; Yongcan Jin

    2015-01-01

    A GH5 hyperthermostable endoglucanase (Ph-GH5) from the archaeon Pyrococcus horikoshii and a commercial endoglucanase (FR) were used to treat bleached eucalyptus pulp (BEP) fibers to produce cellulose nanofibrils (CNF) and subsequently to CNF films. TEM imaging indicated that Ph-GH5 produced longer and more entangled CNF than FR with the same number...

  10. Influence of mechanical environment on the engineering of mineralized tissues using human dental pulp stem cells and silk fibroin scaffolds

    NARCIS (Netherlands)

    Woloszyk, A.; Holsten Dircksen, S.; Bostanci, N.; Müller, R.; Hofmann, S.; Mitsiadis, T.A.

    2015-01-01

    Teeth constitute a promising source of stem cells that can be used for tissue engineering and regenerative medicine purposes. Bone loss in the craniofacial complex due to pathological conditions and severe injuries could be treated with new materials combined with human dental pulp stem cells

  11. Pulp regeneration: Current approaches and future challenges

    Directory of Open Access Journals (Sweden)

    Jingwen eYANG

    2016-03-01

    Full Text Available Regenerative endodontics aims to replace inflamed/necrotic pulp tissues with regenerated pulp-like tissues to revitalize teeth and improve life quality. Pulp revascularization case reports, which showed successful clinical and radiographic outcomes, indicated the possible clinical application of pulp regeneration via cell homing strategy. From a clinical point of view, functional pulp-like tissues should be regenerated with the characterization of vascularization, re-innervation, and dentin deposition with a regulated rate similar to that of normal pulp. Efficient root canal disinfection and proper size of the apical foramen are the two requisite preconditions for pulp regeneration. Progress has been made on pulp regeneration via cell homing strategies. This review focused on the requisite preconditions and cell homing strategies for pulp regeneration. In addition to the traditionally used mechanical preparation and irrigation, antibiotics, irrigation assisted with EndoVac apical negative-pressure system, and ultrasonic and laser irradiation are now being used in root canal disinfection. In addition, pulp-like tissues could be formed with the apical foramen less than 1 mm, although more studies are needed to determine the appropriate size. Moreover, signaling molecules including stromal cell derived factor (SDF-1α, basic Fibroblast Growth Factor (bFGF, Platelet Derived Growth Factor (PDGF, stem cell factor (SCF, and Granulocyte Colony-Stimulating Factor (G-CSF were used to achieve pulp-like tissue formation via a cell homing strategy. Studies on the cell sources of pulp regeneration might give some indications on the signaling molecular selection. The active recruitment of endogenous cells into root canals to regenerate pulp-like tissues is a novel concept that may offer an unprecedented opportunity for the near-term clinical translation of current biology-based therapies for dental pulp regeneration.

  12. Organo mercurials in pulp and paper industry

    Energy Technology Data Exchange (ETDEWEB)

    Bouveng, H O

    1967-01-01

    Today phenyl mercury acetate (PMA) is used in the paper and pulp industry for two purposes: slime control in paper machine systems and impregnation of wet mechanical pulp. PMA is a commonly used slimicide. It is used for slime control in such a way that a minor part (5-20% depending on mill operation) will reach the watercourse with the waste water and contaminate aquatic life. PMA used for impregnation concerns wet mechanical pulp produced for export as raw material, mostly for newsprint. Treatment of this pulp with PMA is necessary to avoid changes caused by molds and rot fungi.

  13. [Vital pulp therapy of damaged dental pulp].

    Science.gov (United States)

    Xuedong, Zhou; Dingming, Huang; Jianguo, Liu; Zhengwei, Huang; Xin, Wei; Deqin, Yang; Jin, Zhao; Liming, Chen; Lin, Zhu; Yanhong, Li; Jiyao, Li

    2017-08-01

    The development of an expert consensus on vital pulp therapy can provide practical guidance for the improvement of pulp damage care in China. Dental pulp disease is a major type of illness that adversely affects human oral health. Pulp capping and pulpotomy are currently the main methods for vital pulp therapy. Along with the development of minimal invasion cosmetic dentistry, using different treatment technologies and materials reasonably, preserving healthy tooth tissue, and extending tooth save time have become urgent problems that call for immediate solution in dental clinics. This paper summarizes the experiences and knowledge of endodontic experts. We develop a clinical path of vital pulp therapy for clinical work by utilizing the nature, approach, and degree of pulp damage as references, defense and self-repairing ability of pulp as guidance, and modern technologies of diagnosis and treatment as means.

  14. Reaction mechanisms and evaluation of effective process operation for catalytic oxidation and coagulation by ferrous solution and hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.H.; Moon, H.J.; Kim, Y.M. [Dept. of Environmental Engineering, Sangmyung Univ., Cheonan (Korea); Bae, W.K. [Dept. of Civil and Environmental Engineering, Hanyang Univ., Ansan, Kyounggi (Korea)

    2003-07-01

    This research was carried out to evaluate the removal efficiencies of COD{sub cr} and colour for the dyeing wastewater by ferrous solution and the different dosage of H{sub 2}O{sub 2} in Fenton process. In the case of H{sub 2}O{sub 2} divided dosage, 7:3 was more effective than 3:7 to remove COD{sub cr} and colour. The results showed that COD was mainly removed by Fenton coagulation, where the ferric ions are formed in the initial step of Fenton reaction. On the other hand colour was removed by Fenton oxidation rather than Fenton coagulation. This paper also aims at pursuing to investigate the effective removal mechanisms using ferrous ion coagulation, ferric ion coagulation and Fenton oxidation process. The removal mechanism of COD{sub cr} and colour was mainly coagulation by ferrous ion, ferric ion and Fenton oxidation. The removal efficiencies were dependent on the ferric ion amount at the beginning of the reaction. However the final removal efficiency of COD and colour was in the order of Fenton oxidation, ferric ion coagulation and ferrous ion coagulation. The reason of the highest removal efficiency by Fenton oxidation can be explained by the chain reactions with ferrous solution, ferric ion and hydrogen peroxide. (orig.)

  15. A novel role for Twist-1 in pulp homeostasis.

    Science.gov (United States)

    Galler, K M; Yasue, A; Cavender, A C; Bialek, P; Karsenty, G; D'Souza, R N

    2007-10-01

    The molecular mechanisms that maintain the equilibrium of odontoblast progenitor cells in dental pulp are unknown. Here we tested whether homeostasis in dental pulp is modulated by Twist-1, a nuclear protein that partners with Runx2 during osteoblast differentiation. Our analysis of Twist-1(+/-) mice revealed phenotypic changes that involved an earlier onset of dentin matrix formation, increased alkaline phosphatase activity, and pulp stones within the pulp. RT-PCR analyses revealed Twist-1 expression in several adult organs, including pulp. Decreased levels of Twist-1 led to higher levels of type I collagen and Dspp gene expression in perivascular cells associated with the pulp stones. In mice heterozygous for both Twist-1 and Runx2 inactivation, the phenotype of pulp stones appeared completely rescued. These findings suggest that Twist-1 plays a key role in restraining odontoblast differentiation, thus maintaining homeostasis in dental pulp. Furthermore, Twist-1 functions in dental pulp are dependent on its interaction with Runx2.

  16. Generation mechanism of hydrogen peroxide in dc plasma with a liquid electrode

    Science.gov (United States)

    Takeuchi, Nozomi; Ishibashi, Naoto

    2018-04-01

    The production mechanism of liquid-phase H2O2 in dc driven plasma in O2 and Ar with a water electrode was investigated. When a water anode was used, the concentration of H2O2 increased linearly with the treatment time. The production rate was proportional to the discharge current, and there was no dependence on the gap distance. On the other hand, the production rate was much smaller with a water anode. We concluded that the production of gas-phase H2O2 in the cathode sheath just above a water cathode and diffusion of this H2O2 into the water constitute the key mechanism in the production of liquid-phase H2O2.

  17. Lipophilic extractives and the loss of solid material in mechanical pulp washing; Rasvaliukoiset uuteaineet ja kiintoainetappiot mekaanisen massan katkaisupesussa - EKT 02

    Energy Technology Data Exchange (ETDEWEB)

    Manner, H; Kaeyhkoe, J; Keskinen, K [Lappeenranta Univ. of Technology (Finland). Lab. of Paper Technology

    1999-12-31

    In this project the aim is to produce basic information for the optimization of mechanical pulp washing. In the first stage, the main emphasis is put on the behavior of lipophilic extractives and on the solid material which is lost during washing. The first task was to make the simulation of mill scale washing processes on a laboratory scale possible. This has been achieved by building two laboratory scale presses and comparing them to mill scale presses. The experimental information obtained there from verified that similar conditions could be obtained on a laboratory scale as from mill scale presses. The main research areas and results obtained in this project are: Washing studies: A considerable deresination efficiency can be obtained in a single washing stage with reasonable water usage. Dissolution and dispersion of wood components in the mixing: Temperature, time and power in the mixing of mechanical pulp has a significant effect on the dispersion of the lipophilic extractives. Also, the dissolution and dispersion of wood components in the mixing may form quite a complex issue to study. Form of the lipophilic extractives in the filtrates: The amount of lipophilic extractives in the solid phase of the filtrates obtained from the presses was so low that it had no effect on the deresination efficiency. The effect of the dispersing agents on the deresination efficiency: The deresination efficiency can be significantly improved by the optimum usage of dispersing agents. Research work in these areas will be continued. (orig.)

  18. Lipophilic extractives and the loss of solid material in mechanical pulp washing; Rasvaliukoiset uuteaineet ja kiintoainetappiot mekaanisen massan katkaisupesussa - EKT 02

    Energy Technology Data Exchange (ETDEWEB)

    Manner, H.; Kaeyhkoe, J.; Keskinen, K. [Lappeenranta Univ. of Technology (Finland). Lab. of Paper Technology

    1998-12-31

    In this project the aim is to produce basic information for the optimization of mechanical pulp washing. In the first stage, the main emphasis is put on the behavior of lipophilic extractives and on the solid material which is lost during washing. The first task was to make the simulation of mill scale washing processes on a laboratory scale possible. This has been achieved by building two laboratory scale presses and comparing them to mill scale presses. The experimental information obtained there from verified that similar conditions could be obtained on a laboratory scale as from mill scale presses. The main research areas and results obtained in this project are: Washing studies: A considerable deresination efficiency can be obtained in a single washing stage with reasonable water usage. Dissolution and dispersion of wood components in the mixing: Temperature, time and power in the mixing of mechanical pulp has a significant effect on the dispersion of the lipophilic extractives. Also, the dissolution and dispersion of wood components in the mixing may form quite a complex issue to study. Form of the lipophilic extractives in the filtrates: The amount of lipophilic extractives in the solid phase of the filtrates obtained from the presses was so low that it had no effect on the deresination efficiency. The effect of the dispersing agents on the deresination efficiency: The deresination efficiency can be significantly improved by the optimum usage of dispersing agents. Research work in these areas will be continued. (orig.)

  19. Hydrogen peroxide increases depolarization-induced contraction of mechanically skinned slow twitch fibres from rat skeletal muscles.

    Science.gov (United States)

    Plant, David R; Lynch, Gordon S; Williams, David A

    2002-03-15

    The effect of exogenous hydrogen peroxide (H(2)O(2)) on excitation-contraction (E-C) coupling and sarcoplasmic reticulum (SR) function was compared in mechanically skinned slow twitch fibres (prepared from the soleus muscles) and fast twitch fibres (prepared from the extensor digitorum longus; EDL muscles) of adult rats. Equilibration (5 min) with 1 mM H(2)O(2) diminished the ability of the Ca(2+)-depleted SR to reload Ca(2+) in both slow (P fast twitch fibres (P fast twitch fibres by 24 +/- 5 % (P slow twitch fibres. Treatment with 1 mM H(2)O(2) also increased the peak force of low [caffeine] contracture by approximately 45% in both fibre types compared to control (P slow twitch fibres, compared to control (no H(2)O(2); P fast twitch fibres was not altered by 1 mM H(2)O(2) treatment. Equilibration with 5 mM H(2)O(2) induced a spontaneous force response in both slow and fast twitch fibres, which could be partly reversed by 2 min treatment with 10 mM DTT. Peak DICR was also increased approximately 40% by 5 mM H(2)O(2) in slow twitch fibres compared to control (no H(2)O(2); P slow but not fast twitch fibres. The increase in depolarization-induced contraction in slow twitch fibres might be mediated by an increased SR Ca(2+) release during contraction and/or an increase in Ca(2+) sensitivity.

  20. Papaya pulp gelling: is it premature ripening or problems of water accumulation in the apoplast?

    Directory of Open Access Journals (Sweden)

    Jurandi Gonçalves de Oliveira

    Full Text Available Gelled aspect in papaya fruit is typically confused with premature ripening. This research reports the characterization of this physiological disorder in the pulp of papaya fruit by measuring electrolyte leakage, Pi content, lipid peroxidation, pulp firmness, mineral contents (Ca, Mg and K - in pulp and seed tissues, and histological analysis of pulp tissue. The results showed that the gelled aspect of the papaya fruit pulp is not associated with tissue premature ripening. Data indicate a reduction of the vacuole water intake as the principal cause of the loss of cellular turgor; while the waterlogged aspect of the tissue may be due to water accumulation in the apoplast.

  1. Influence of rice straw cooking conditions in the soda-ethanol-water pulping on the mechanical properties of produced paper sheets.

    Science.gov (United States)

    Navaee-Ardeh, S; Mohammadi-Rovshandeh, J; Pourjoozi, M

    2004-03-01

    A normalized design was used to examine the influence of independent variables (alcohol concentration, cooking time and temperature) in the catalytic soda-ethanol pulping of rice straw on various mechanical properties (breaking length, burst, tear index and folding endurance) of paper sheets obtained from each pulping process. An equation of each dependent variable as a function of cooking variables (independent variables) was obtained by multiple non-linear regression using the least square method by MATLAB software for developing of empirical models. The ranges of alcohol concentration, cooking time and temperature were 40-65% (w/w), 150-180 min and 195-210 degrees C, respectively. Three-dimensional graphs of dependent variables were also plotted versus independent variables. The optimum values of breaking length, burst and tear index and folding endurance were 4683.7 (m), 30.99 (kN/g), 376.93 (mN m2/g) and 27.31, respectively. However, short cooking time (150 min), high ethanol concentration (65%) and high temperature (210 degrees C) could be used to produce papers with suitable burst and tear index. However, for papers with best breaking length and folding endurance low temperature (195 degrees C) was desirable. Differences between optimum values of dependent variables obtained by normalized design and experimental data were less than 20%.

  2. Human dental pulp-derived stem cells promote locomotor recovery after complete transection of the rat spinal cord by multiple neuro-regenerative mechanisms.

    Science.gov (United States)

    Sakai, Kiyoshi; Yamamoto, Akihito; Matsubara, Kohki; Nakamura, Shoko; Naruse, Mami; Yamagata, Mari; Sakamoto, Kazuma; Tauchi, Ryoji; Wakao, Norimitsu; Imagama, Shiro; Hibi, Hideharu; Kadomatsu, Kenji; Ishiguro, Naoki; Ueda, Minoru

    2012-01-01

    Spinal cord injury (SCI) often leads to persistent functional deficits due to loss of neurons and glia and to limited axonal regeneration after injury. Here we report that transplantation of human dental pulp stem cells into the completely transected adult rat spinal cord resulted in marked recovery of hind limb locomotor functions. Transplantation of human bone marrow stromal cells or skin-derived fibroblasts led to substantially less recovery of locomotor function. The human dental pulp stem cells exhibited three major neuroregenerative activities. First, they inhibited the SCI-induced apoptosis of neurons, astrocytes, and oligodendrocytes, which improved the preservation of neuronal filaments and myelin sheaths. Second, they promoted the regeneration of transected axons by directly inhibiting multiple axon growth inhibitors, including chondroitin sulfate proteoglycan and myelin-associated glycoprotein, via paracrine mechanisms. Last, they replaced lost cells by differentiating into mature oligodendrocytes under the extreme conditions of SCI. Our data demonstrate that tooth-derived stem cells may provide therapeutic benefits for treating SCI through both cell-autonomous and paracrine neuroregenerative activities.

  3. Nanofibrillated cellulose as paper additive in Eucalyptus pulps

    Directory of Open Access Journals (Sweden)

    Israel González

    2012-11-01

    Full Text Available In this work, the physical and mechanical properties of bleached Eucalyptus pulp reinforced with nanofibrillated cellulose (NFC are compared with those of traditional beaten pulp used in the making of writing/printing and offset printing papers. For this purpose, three different types of hardwood slurries were prepared: beaten pulps, unbeaten pulps reinforced with NFC, and slightly beaten pulps also reinforced with NFC. Physical and mechanical tests were performed on handsheets from these different slurries. The results showed that adding NFC to unbeaten pulps results in physical and mechanical properties similar to those in pulps used for printing/writing papers. Nevertheless, the best results were obtained in slurries previously beaten at slight conditions and subsequently reinforced with NFC. These results demonstrate that the addition of NFC allows a reduction in beating intensity without decreasing the desired mechanical properties for this specific purpose.

  4. The Effects of Short Wave UV Irradiation (254-366nm on Color Values of Recycled and Bleached ONP/OMP Pulps

    Directory of Open Access Journals (Sweden)

    Emrah Peşman

    2011-04-01

    Full Text Available ABSTRACT As it is known, mechanical pulp papers include significant amount of lignin and carbohydrates as well as cellulose. Thus, when these lignin reach papers irradiated with short wave UV light they could not protect their color. In this study, bleaching of ONP/OMG recycled pulps with hydrogen peroxide, sodium percarbonate, sodium dithyonite, sodium borohydride and formamidin sulfunic acid were performed. Then the test papers of these pulps were irradiated with 254-366nm UV light and changes in the ISO Brightness, CIE L*a*b*, yellowness (YI and whiteness (WI values were observed. At the result of study, all bleaching agents were determined as insufficient in the respect of color stability. But if they compared with each other, the two stages sodium percarbonate-sodium borohydride bleaching sequence was gave the best results against to color reversion. Keywords: Old news/old magazine papers (ONP/OMG, Bleaching, Color Stability, UV Irradiation

  5. [The study of the protective effect and its mechanism of Edaravone to neurons with hydrogen peroxide stimulated].

    Science.gov (United States)

    Long, Hao; Zhang, Ning; Fan, Jin; Li, Qing-qing; Li, Yi-ming; Tang, Jian; Cheng, Gang; Yin, Guo-yong; Cai, Wei-hua

    2013-03-01

    To prove the protective effect of Edaravone to neurons and to study the particular mechanism. Neurons were collected from 18-day fetal rat brains and a culture of almost pure neurons was obtained after 14-day culture, then the cells were randomly assigned to one of the three groups: control group, hydrogen peroxide (H₂O₂)-treated group, and Edaravone-treated group. In H₂O₂-treated group, 300 µmol/L H₂O₂ was added to the medium, followed by returning to the normal culture for the presupposition of time. In Edaravone-treated group, 500 µmol/L Edaravone was prophylactically added to the medium for 30 minutes before the insult. Morphology of mitochondria was visualized by transmission electron microscopy. The rate of apoptotic cells was detected by flow cytometry analysis. The relationships between the proteins and the key proteins expressions were observed by immunoprecipitation and immunoblotting. Compared to the Edaravone-treated group, mitochondria in H₂O₂-treated group displayed more vesicular matrix compartments at the same time. Percentage of apoptotic cells in H₂O₂-treated group after 0.5, 2, 6 and 12 h were 14.40% ± 1.23%, 45.50% ± 2.81%, 56.40% ± 3.53%, 62.50% ± 4.23%, which were higher than control group (F = 274.8, P Edaravone-treated group were 0.90% ± 0.07%, 1.10% ± 0.08%, 3.50% ± 1.90%, 12.60% ± 1.10%, which were lower than H₂O₂-treated group (F = 362.7, P Edaravone-treated group. As a free radical scavenger, the Edaravone could protect neurons by inhibiting the activity of JNK, the disassociation of BAD from 14-3-3 and the translocation of BAX from the cytosol to mitochondria.

  6. Activation of rho is involved in the mechanism of hydrogen-peroxide-induced lung edema in isolated perfused rabbit lung.

    Science.gov (United States)

    Chiba, Y; Ishii, Y; Kitamura, S; Sugiyama, Y

    2001-09-01

    Acute lung injury is attributed primarily to increased vascular permeability caused by reactive oxygen species derived from neutrophils, such as hydrogen peroxide (H2O2). Increased permeability is accompanied by the contraction and cytoskeleton reorganization of endothelial cells, resulting in intercellular gap formation. The Rho family of Ras-like GTPases is implicated in the regulation of the cytoskeleton and cell contraction. We examined the role of Rho in H2O2-induced pulmonary edema with the use of isolated perfused rabbit lungs. To our knowledge, this is the first study to examine the role of Rho in increased vascular permeability induced by H2O2 in perfused lungs. Vascular permeability was evaluated on the basis of the capillary filtration coefficient (Kfc, ml/min/cm H2O/100 g). We found that H2O2 (300 microM) increased lung weight, Kfc, and pulmonary capillary pressure. These effects of H2O2 were abolished by treatment with Y-27632 (50 microM), an inhibitor of the Rho effector p160 ROCK. In contrast, the muscular relaxant papaverine inhibited the H2O2-induced rise in pulmonary capillary pressure, but did not suppress the increases in lung weight and Kfc. These findings indicate that H2O2 causes pulmonary edema by elevating hydrostatic pressure and increasing vascular permeability. Y-27632 inhibited the formation of pulmonary edema by blocking both of these H2O2-induced effects. Our results suggest that Rho-related pathways have a part in the mechanism of H2O2-induced pulmonary edema. Copyright 2001 Academic Press.

  7. ON THE RECOVERY OF HEMICELLULOSE BEFORE KRAFT PULPING

    Directory of Open Access Journals (Sweden)

    Carlos Vila,

    2012-07-01

    Full Text Available To assess the feasibility of implementing hemicellulose recovery stages in kraft mills, Eucalyptus globulus wood samples were subjected to aqueous treatments with hot, compressed water (autohydrolysis processing to achieve partial dissolution of xylan. Autohydrolyzed solids were subjected to kraft pulping under selected conditions to yield a pulp of low kappa number, and to an optimized TCF bleaching sequence made up of three stages (alkaline oxygen delignification, chelating, and pressurized hydrogen peroxide, with minimized additions of pulping and bleaching chemicals. The final product had a relatively low kappa number (1.4, 641 mL/g ISO intrinsic viscosity, and 86.4% brightness.

  8. Optimization of Dithionite Bleaching of High Yield Bagasse Pulp

    International Nuclear Information System (INIS)

    Mohamed, E.

    2005-01-01

    High yield bagasse pulp was prepared by soaking bagasse in 10 % cold sodium hydroxide for 24 hours and then refluxing for two hours at 95 degree C. Optimization of dithionite bleaching was attained by investigation of different parameters as consistency, temperature, time and ph. Effect of additives as chelating agent (EDTA) or stabilizing of bleaching solution (Zn compound and hexamethylene tetramine) was considered. The effect of air content was also studied. One and two stages bleaching of the pulp were investigated by using sodium dithionite (D) as a sole bleaching agent or after application of one stage bleaching by hydrogen peroxide to attain high brightness for high yield pulp

  9. Gamma ray induced chromophore modification of softwood thermomechanical pulp

    International Nuclear Information System (INIS)

    Robert, S.; Daneault, C.; Viel, C.; Lepine, F.

    1992-01-01

    This study focuses on bleaching a softwood (black spruce, balsam fur) thermomechanical pulp with gamma rays. Gamma rays are known for their enormous penetrating power, along with their ionizing properties. They can generate highly energetic radicals capable of oxidizing lignin chromophores. The authors studied the influence of isopropyl alcohol, sodium borohydride, oxygen, hydrogen peroxide, nitrogen dioxide and water along with gamma ray irradiation of the pulps. The authors measured the optimal dose and dose rate, along with the influence of the radical scavengers like oxygen on the bleaching effect of gamma irradiated pulps. They observe various degrees of bleaching of these pulps. Evidence relates this bleaching to the generation of perhydroxyl anions upon irradiation of water. Also, they were able to pinpoint the influence of the dose rate on the rate of formation and disappearance of these perhydroxyl anions and their influence on bleaching kinetics. Stability toward photoyellowing, and photoyellowing's kinetic of papers from these pulps was also studied

  10. In vitro pharmacological characterization of a novel TRPA1 antagonist and proof of mechanism in a human dental pulp model

    Directory of Open Access Journals (Sweden)

    Nyman E

    2013-01-01

    Full Text Available Eva Nyman,1,* Bo Franzén,1,* Andreas Nolting,1 Göran Klement,1 Gang Liu,1 Maria Nilsson,1 Annika Rosén,2 Charlotta Björk,3 Dirk Weigelt,4 Patrik Wollberg,1 Paul Karila,1 Patrick Raboisson11Neuroscience, Innovative Medicines CNS/Pain, AstraZeneca R&D, Södertälje, Sweden; 2Division of Oral and Maxillofacial Surgery, Karolinska Institute/Karolinska University Hospital, Huddinge, Sweden; 3Clinical TA NS Early Development, 4Medicinal Chemistry, Innovative Medicines CNS/Pain, AstraZeneca R&D, Södertälje, Sweden*These authors contributed equally to this workAbstract: AZ465 is a novel selective transient receptor potential cation channel, member A1 (TRPA1 antagonist identified during a focused drug discovery effort. In vitro, AZ465 fully inhibits activation by zinc, O-chlorobenzylidene malononitrile (CS, or cinnamaldehyde of the human TRPA1 channel heterologously expressed in human embryonic kidney cells. Our data using patch-clamp recordings and mouse/human TRPA1 chimeras suggest that AZ465 binds reversibly in the pore region of the human TRPA1 channel. Finally, in an ex vivo model measuring TRPA1 agonist-stimulated release of neuropeptides from human dental pulp biopsies, AZD465 was able to block 50%–60% of CS-induced calcitonin gene-related peptide release, confirming that AZ465 inhibits the native human TRPA1 channel in neuronal tissue.Keywords: pain, pharmacology, antagonist, chimeric proteins, dental pulp, inflammation, neuropeptide, calcitonin gene-related peptide, CGRP

  11. Spectrophotometric Evaluation of the Pulpal Peroxide Levels in Intact and Restored Teeth - An Invitro Study.

    Science.gov (United States)

    Patri, Gaurav; Acharya, Gourismita; Agrawal, Pratik; Panda, Vijeta

    2016-08-01

    Hydrogen peroxide (30%) is a commonly used "in office" bleaching agent. Deleterious effects of hydrogen peroxide on the pulp have been observed. The present study was conducted with the aim to evaluate the penetration of 30% hydrogen peroxide into the pulp chamber through intact teeth and through the surface of teeth, restored with either hybrid composite or Resin Modified Glass Ionomer Cement (RMGIC). Sixty extracted human maxillary central incisors were selected and divided into six groups. Two groups were restored with hybrid composite resin and two with RMGIC, while two groups were left intact. The teeth with acetate buffer solution in their pulp cavity were then immersed in either 30% hydrogen peroxide or distilled water depending upon the group, for 60 minutes at 37°C. Then horseradish peroxidase and leucocrystal violet were added to the acetate buffer solution present in the pulp chamber after it was transferred to a test tube and the optical density of the resultant blue solution obtained was measured spectrophotometrically. The data obtained were analyzed using one way ANOVA and Student's t-test. The data obtained established that hydrogen peroxide penetrated into the pulp from the bleaching agent used. Hydrogen peroxide (30%) showed the highest pulpal peroxide level in teeth restored with RMGIC followed by teeth restored with hybrid composite resin and the least amount of penetration was observed in intact teeth. The amount of peroxide penetration into the tooth is more through restored tooth than intact tooth and is also dependant on the type of restorative materials used.

  12. High-yield pulping effluent treatment technologies

    International Nuclear Information System (INIS)

    Su, W.X.; Hsieh, J.S.

    1993-03-01

    The objective of this report is to examine the high-yield (mechanical) pulp processes with respect to environmental issues affected by the discharge of their waste streams. Various statistics are given that support the view that high-yield pulping processes will have major growth in the US regions where pulp mills are located, and sites for projects in the development phase are indicated. Conventional and innovative effluent-treatment technologies applicable to these processes are reviewed. The different types of mechanical pulping or high-yield processes are explained, and the chemical additives are discussed. The important relationship between pulp yield and measure of BOD in the effluent is graphically presented. Effluent contaminants are identified, along with other important characteristics of the streams. Current and proposed environmental limitations specifically related to mechanical pulp production are reviewed. Conventional and innovative effluent-treatment technologies are discussed, along with their principle applications, uses, advantages, and disadvantages. Sludge management and disposal techniques become an intimate part of the treatment of waste streams. The conclusion is made that conventional technologies can successfully treat effluent streams under current waste-water discharge limitations, but these systems may not be adequate when stricter standards are imposed. At present, the most important issue in the treatment of pulp-mill waste is the management and disposal of the resultant sludge

  13. The Influence of Chemical Surface Modification of Kenaf Fiber using Hydrogen Peroxide on the Mechanical Properties of Biodegradable Kenaf Fiber/Poly(Lactic Acid Composites

    Directory of Open Access Journals (Sweden)

    Nur Inani Abdul Razak

    2014-03-01

    Full Text Available Bleaching treatment of kenaf fiber was performed in alkaline medium containing hydrogen peroxide solution maintained at pH 11 and 80 °C for 60 min. The bleached kenaf fiber was analyzed using Fourier Transform Infrared (FTIR and X-ray Diffraction (XRD analysis. The bleached kenaf fiber was then compounded with poly-(lactic acid (PLA via a melt blending method. The mechanical (tensile, flexural and impact performance of the product was tested. The fiber treatment improved the mechanical properties of PLA/bleached kenaf fiber composites. Scanning electron micrograph (SEM morphological analysis showed improvement of the interfacial adhesion between the fiber surface and polymer matrix.

  14. Purification and recycling of the waste water of a paper mill using mechanical pulp; Mekaanista massaa kaeyttaevaen paperitehtaan jaeteveden puhdistus ja uudelleenkaeyttoe - EKY 07

    Energy Technology Data Exchange (ETDEWEB)

    Mattelemaeki, R [Enso Oyj, Imatra (Finland)

    1999-12-31

    The objective of the project was to study which levels of organic and inorganic substances could be obtained by treatment of waste waters of mechanical pulper and paper machine biologically and after that with solid matter removal. Another target was also to test the utilisation of the purified water in pulp and paper manufacture, and to study the properties of purified water. The three months test runs with PK 4 and TMP plant clarified waters were carried out using a pilot-scale plant, which also consisted of two serial aerobic bioreactors and a parallel anaerobic line as a reference. The solid matter was removed by chemical flocculation, flotation and sand filtration. The purification efficiencies of both waters were similar both in aerobic and anaerobic lines. The reduction of soluble COD in biological stage was about 75 % and that of the whole line about 85 %. The solid matter reduction was 60-70 %. Solid fines, including bacteria, could not be removed sufficiently from the water by flotation and sand filtration so the water cannot be recommended to be used to replace fresh water. Circulating water sheets were produced, and pulp washing tests, retention tests and microbiological tests were carried out in order to estimate the recyclability of the water. Minor lowering of whiteness of the sheets were observed when a part of the fresh water was replaced with recycled water. Microscopic analysis shoved that after the sand filter there were a lot of free bacteria in the water. Further research will be concentrated to recycling of purified water, e.g. To research on how the colour of the water effects on the quality of the product. (orig.)

  15. Purification and recycling of the waste water of a paper mill using mechanical pulp; Mekaanista massaa kaeyttaevaen paperitehtaan jaeteveden puhdistus ja uudelleenkaeyttoe - EKY 07

    Energy Technology Data Exchange (ETDEWEB)

    Mattelemaeki, R. [Enso Oyj, Imatra (Finland)

    1998-12-31

    The objective of the project was to study which levels of organic and inorganic substances could be obtained by treatment of waste waters of mechanical pulper and paper machine biologically and after that with solid matter removal. Another target was also to test the utilisation of the purified water in pulp and paper manufacture, and to study the properties of purified water. The three months test runs with PK 4 and TMP plant clarified waters were carried out using a pilot-scale plant, which also consisted of two serial aerobic bioreactors and a parallel anaerobic line as a reference. The solid matter was removed by chemical flocculation, flotation and sand filtration. The purification efficiencies of both waters were similar both in aerobic and anaerobic lines. The reduction of soluble COD in biological stage was about 75 % and that of the whole line about 85 %. The solid matter reduction was 60-70 %. Solid fines, including bacteria, could not be removed sufficiently from the water by flotation and sand filtration so the water cannot be recommended to be used to replace fresh water. Circulating water sheets were produced, and pulp washing tests, retention tests and microbiological tests were carried out in order to estimate the recyclability of the water. Minor lowering of whiteness of the sheets were observed when a part of the fresh water was replaced with recycled water. Microscopic analysis shoved that after the sand filter there were a lot of free bacteria in the water. Further research will be concentrated to recycling of purified water, e.g. To research on how the colour of the water effects on the quality of the product. (orig.)

  16. Microstructure and mechanical properties of 2024-T3 and 7075-T6 aluminum alloys and austenitic stainless steel 304 after being exposed to hydrogen peroxide

    Science.gov (United States)

    Sofyan, Nofrijon Bin Imam

    The effect of hydrogen peroxide used as a decontaminant agent on selected aircraft metallic materials has been investigated. The work is divided into three sections; bacterial attachment behavior onto an austenitic stainless steel 304 surface; effect of decontamination process on the microstructure and mechanical properties of aircraft metallic structural materials of two aluminum alloys, i.e. 2024-T3 and 7075-T6, and an austenitic stainless steel 304 as used in galley and lavatory surfaces; and copper dissolution rate into hydrogen peroxide. With respect to bacterial attachment, the results show that surface roughness plays a role in the attachment of bacteria onto metallic surfaces at certain extent. However, when the contact angle of the liquid on a surface increased to a certain degree, detachment of bacteria on that surface became more difficult. In its relation to the decontamination process, the results show that a corrosion site, especially on the austenitic stainless steel 304 weld and its surrounding HAZ area, needs more attention because it could become a source or a harborage of bio-contaminant agent after either incidental or intentional bio-contaminant delivery. On the effect of the decontamination process on the microstructure and mechanical properties of aircraft metallic structural materials, the results show that microstructural effects are both relatively small in magnitude and confined to a region immediately adjacent to the exposed surface. No systematic effect is found on the tensile properties of the three alloys under the conditions examined. The results of this investigation are promising with respect to the application of vapor phase hydrogen peroxide as a decontaminant agent to civilian aircraft, in that even under the most severe circumstances that could occur; only very limited damage was observed. The results from the dissolution of copper by concentrated liquid hydrogen peroxide showed that the rate of copper dissolution increased for

  17. Region-specific vulnerability to lipid peroxidation and evidence of neuronal mechanisms for polyunsaturated fatty acid biosynthesis in the healthy adult human central nervous system.

    Science.gov (United States)

    Naudí, Alba; Cabré, Rosanna; Dominguez-Gonzalez, Mayelin; Ayala, Victoria; Jové, Mariona; Mota-Martorell, Natalia; Piñol-Ripoll, Gerard; Gil-Villar, Maria Pilar; Rué, Montserrat; Portero-Otín, Manuel; Ferrer, Isidre; Pamplona, Reinald

    2017-05-01

    Lipids played a determinant role in the evolution of the brain. It is postulated that the morphological and functional diversity among neural cells of the human central nervous system (CNS) is projected and achieved through the expression of particular lipid profiles. The present study was designed to evaluate the differential vulnerability to oxidative stress mediated by lipids through a cross-regional comparative approach. To this end, we compared 12 different regions of CNS of healthy adult subjects, and the fatty acid profile and vulnerability to lipid peroxidation, were determined by gas chromatography (GC) and gas chromatography/mass spectrometry (GC/MS), respectively. In addition, different components involved in PUFA biosynthesis, as well as adaptive defense mechanisms against lipid peroxidation, were also measured by western blot and immunohistochemistry, respectively. We found that: i) four fatty acids (18.1n-9, 22:6n-3, 20:1n-9, and 18:0) are significant discriminators among CNS regions; ii) these differential fatty acid profiles generate a differential selective neural vulnerability (expressed by the peroxidizability index); iii) the cross-regional differences for the fatty acid profiles follow a caudal-cranial gradient which is directly related to changes in the biosynthesis pathways which can be ascribed to neuronal cells; and iv) the higher the peroxidizability index for a given human brain region, the lower concentration of the protein damage markers, likely supported by the presence of adaptive antioxidant mechanisms. In conclusion, our results suggest that there is a region-specific vulnerability to lipid peroxidation and offer evidence of neuronal mechanisms for polyunsaturated fatty acid biosynthesis in the human central nervous system. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Laccase-Catalyzed Surface Modification of Thermo-Mechanical Pulp (TMP) for the Production of Wood Fiber Insulation Boards Using Industrial Process Water

    Science.gov (United States)

    Schubert, Mark; Ruedin, Pascal; Civardi, Chiara; Richter, Michael; Hach, André; Christen, Herbert

    2015-01-01

    Low-density wood fiber insulation boards are traditionally manufactured in a wet process using a closed water circuit (process water). The water of these industrial processes contains natural phenolic extractives, aside from small amounts of admixtures (e.g., binders and paraffin). The suitability of two fungal laccases and one bacterial laccase was determined by biochemical characterization considering stability and substrate spectra. In a series of laboratory scale experiments, the selected commercial laccase from Myceliophtora thermophila was used to catalyze the surface modification of thermo-mechanical pulp (TMP) using process water. The laccase catalyzed the covalent binding of the phenolic compounds of the process water onto the wood fiber surface and led to change of the surface chemistry directly via crosslinking of lignin moieties. Although a complete substitution of the binder was not accomplished by laccase, the combined use of laccase and latex significantly improved the mechanical strength properties of wood fiber boards. The enzymatically-treated TMP showed better interactions with the synthetic binder, as shown by FTIR-analysis. Moreover, the enzyme is extensively stable in the process water and the approach requires no fresh water as well as no cost-intensive mediator. By applying a second-order polynomial model in combination with the genetic algorithm (GA), the required amount of laccase and synthetic latex could be optimized enabling the reduction of the binder by 40%. PMID:26046652

  19. Pulp stem cells: implication in reparative dentin formation.

    Science.gov (United States)

    Dimitrova-Nakov, Sasha; Baudry, Anne; Harichane, Yassine; Kellermann, Odile; Goldberg, Michel

    2014-04-01

    Many dental pulp stem cells are neural crest derivatives essential for lifelong maintenance of tooth functions and homeostasis as well as tooth repair. These cells may be directly implicated in the healing process or indirectly involved in cell-to-cell diffusion of paracrine messages to resident (pulpoblasts) or nonresident cells (migrating mesenchymal cells). The identity of the pulp progenitors and the mechanisms sustaining their regenerative capacity remain largely unknown. Taking advantage of the A4 cell line, a multipotent stem cell derived from the molar pulp of mouse embryo, we investigated the capacity of these pulp-derived precursors to induce in vivo the formation of a reparative dentin-like structure upon implantation within the pulp of a rodent incisor or a first maxillary molar after surgical exposure. One month after the pulp injury alone, a nonmineralized fibrous matrix filled the mesial part of the coronal pulp chamber. Upon A4 cell implantation, a mineralized osteodentin was formed in the implantation site without affecting the structure and vitality of the residual pulp in the central and distal parts of the pulp chamber. These results show that dental pulp stem cells can induce the formation of reparative dentin and therefore constitute a useful tool for pulp therapies. Finally, reparative dentin was also built up when A4 progenitors were performed by alginate beads, suggesting that alginate is a suitable carrier for cell implantation in teeth. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  20. REPLACEMENT OF SOFTWOOD KRAFT PULP WITH ECF-BLEACHED BAMBOO KRAFT PULP IN FINE PAPER

    Directory of Open Access Journals (Sweden)

    Guanglei Zhao

    2010-06-01

    Full Text Available Non-wood fibers such as bamboo and wheat straw have been playing important roles in the pulp and paper industry in China. In this study an ECF-bleached bamboo kraft pulp was compared with a bleached softwood kraft pulp (NBSK as the reinforcement pulp in fine paper production. Areas that were examined include the refining of pure fibers, influence of bamboo on dewatering, retention, and sizing. The influence of bamboo kraft pulp as a part of a furnish replacing NBSK was compared as well. Results show that fiber shortening was more prominent with bamboo when refined. This resulted in a higher amount of fines, and addition wet-end chemicals may be required to compensate. Handsheets with bamboo as a reinforcement fiber showed similar mechanical and optical properties to handsheets containing NBSK.

  1. Protective mechanisms of melatonin against hydrogen-peroxide-induced toxicity in human bone-marrow-derived mesenchymal stem cells.

    Science.gov (United States)

    Mehrzadi, Saeed; Safa, Majid; Kamrava, Seyed Kamran; Darabi, Radbod; Hayat, Parisa; Motevalian, Manijeh

    2017-07-01

    Many obstacles compromise the efficacy of bone marrow mesenchymal stem cells (BM-MSCs) by inducing apoptosis in the grafted BM-MSCs. The current study investigates the effect of melatonin on important mediators involved in survival of BM-MSCs in hydrogen peroxide (H 2 O 2 ) apoptosis model. In brief, BM-MSCs were isolated, treated with melatonin, and then exposed to H 2 O 2 . Their viability was assessed by MTT assay and apoptotic fractions were evaluated through Annexin V, Hoechst staining, and ADP/ATP ratio. Oxidative stress biomarkers including ROS, total antioxidant power (TAP), superoxide dismutase (SOD) and catalase (CAT) activity, glutathione (GSH), thiol molecules, and lipid peroxidation (LPO) levels were determined. Secretion of inflammatory cytokines (TNF-α and IL-6) were measured by ELISA assay. The protein expression of caspase-3, Bax, and Bcl-2, was also evaluated by Western blotting. Melatonin pretreatment significantly increased viability and decreased apoptotic fraction of H 2 O 2 -exposed BM-MSCs. Melatonin also decreased ROS generation, as well as increasing the activity of SOD and CAT enzymes and GSH content. Secretion of inflammatory cytokines in H 2 O 2 -exposed cells was also reduced by melatonin. Expression of caspase-3 and Bax proteins in H 2 O 2 -exposed cells was diminished by melatonin pretreatment. The findings suggest that melatonin may be an effective protective agent against H 2 O 2 -induced oxidative stress and apoptosis in MSC.

  2. Comparative effect of mechanical beating and nanofibrillation of cellulose on paper properties made from bagasse and softwood pulps.

    Science.gov (United States)

    Afra, Elyas; Yousefi, Hossein; Hadilam, Mohamad Mahdi; Nishino, Takashi

    2013-09-12

    Cellulose fibers were fibrillated using mechanical beating (shearing refiner) and ultra-fine friction grinder, respectively. The fibrillated fibers were then used to make paper. Mechanical beating process created a partial skin fibrillation, while grinding turned fiber from micro to nanoscale through nanofibrillation mechanism. The partially fibrillated and nano fibrillated fibers had significant effects on paper density, tear strength, tensile strength and water drainage time. The effect of nanofibrillation on paper properties was quantitatively higher than that of mechanical beating. Paper sheets from nanofibrillated cellulose have a higher density, higher tensile strength and lower tear strength compared to those subjected to mechanical beating. Mechanical beating and nanofibrillation were both found to be promising fiber structural modifications. Long water drainage time was an important drawback of both fibrillation methods. Copyright © 2013 Elsevier Ltd. All rights reserved.

  3. Evaluating pulp stiffness from fibre bundles by ultrasound

    Science.gov (United States)

    Karppinen, Timo; Montonen, Risto; Määttänen, Marjo; Ekman, Axel; Myllys, Markko; Timonen, Jussi; Hæggström, Edward

    2012-06-01

    A non-destructive ultrasonic tester was developed to measure the stiffness of pulp bundles. The mechanical properties of pulp are important when estimating the behaviour of paper under stress. Currently available pulp tests are tedious and alter the fibres structurally and mechanically. The developed tester employs (933 ± 15) kHz tweezer-like ultrasonic transducers and time-of-flight measurement through (9.0 ± 2.5) mm long and (0.8 ± 0.1) mm thick fibre bundles kept at (19.1 ± 0.4) °C and (62 ± 1)% RH. We determined the stiffness of soft wood pulps produced by three kraft pulping modifications: standard kraft pulp, (5.2 ± 0.4) GPa, prehydrolysis kraft pulp, (4.3 ± 0.4) GPa, and alkali extracted prehydrolysis kraft pulp, (3.3 ± 0.4) GPa. Prehydrolysis and alkali extraction processes mainly lowered the hemicellulose content of the pulps, which essentially decreased the fibre-wall stiffness hence impairing the stiffness of the fibre networks. Our results indicate that the method allows ranking of pulps according to their stiffness determined from bundle-like samples taken at an early phase of the papermaking process.

  4. Performance of Schizolobium amazonicum Wood in Bleached Kraft Pulp Production

    Directory of Open Access Journals (Sweden)

    Camila Sarto

    2015-05-01

    Full Text Available This study aimed to evaluate the characteristics of Schizolobium amazonicum wood, specifically its performance in bleached kraft pulp production and the characteristics of its pulp. Chips of Schizolobium amazonicum and Eucalyptus grandis x Eucalyptus urophylla (reference were used. The following parameters were evaluated in the wood: basic density, total extractives, total lignin, holocellulose, and fiber morphology. The pulping simulations were carried out in a laboratory digester, with parameters set to obtain pulp with kappa number 19 ± 0.5. Both pulps were bleached in a PFI mill and submitted to physical-mechanical tests. The results showed that S. amazonicum wood has low basic density and higher content of extractives when compared to E. grandis x E. urophylla wood. For pulping, S. amazonicum required higher alkali charge and H factor to achieve the same delignification level of E. grandis x E. urophylla, resulting in a lower yield, pulp with lower viscosity, and higher wood specific consumption. During bleaching, the brightness gain and final viscosity of S. amazonicum pulp were lower than E. grandis x E. urophylla pulp. Moreover, S. amazonicum pulp had worse physical-mechanical characteristics than E. grandis x E. urophylla.

  5. [Daily practice and pulp diseases].

    Science.gov (United States)

    Calmein, S; Claisse, A

    1990-09-01

    Constructive or destructive processes of pulp tissue depend on many factors: anatomic topography, particular physiology, or intensity and duration of infectious, mechanical and chemical aggression. Also irritation of the pulpo-dentinal complex induce histologic and physiologic changes. The positive diagnosis of hyperemia, acute or chronic pulpitis, pulpal necrosis and acute or chronic apical abscess is performed by clinical investigations which allow a differential diagnosis with other dental or extra-dental diseases. These multiple steps lead to an adapted and appropriate treatment.

  6. Hydrogen peroxide and caustic soda: Dancing with a dragon while bleaching

    Science.gov (United States)

    Peter W. Hart; Carl Houtman; Kolby Hirth

    2013-01-01

    When hydrogen peroxide is mixed with caustic soda, an auto-accelerating reaction can lead to generation of significant amounts of heat and oxygen. On the basis of experiments using typical pulp mill process concentration and temperatures, a relatively simple kinetic model has been developed. Evaluation of these model results reveals that hydrogen peroxide-caustic soda...

  7. The influence of lignin on steam pretreatment and mechanical pulping of poplar to achieve high sugar recovery and ease of enzymatic hydrolysis.

    Science.gov (United States)

    Chandra, Richard P; Chu, QiuLu; Hu, Jinguang; Zhong, Na; Lin, Mandy; Lee, Jin-Suk; Saddler, Jack

    2016-01-01

    With the goal of enhancing overall carbohydrate recovery and reducing enzyme loading refiner mechanical pulping and steam pretreatment (210°C, 5 min) were used to pretreat poplar wood chips. Neutral sulphonation post-treatment indicated that, although the lignin present in the steam pretreated substrate was less reactive, the cellulose-rich, water insoluble component was more accessible to cellulases and Simons stain. This was likely due to lignin relocation as the relative surface lignin measured by X-ray photoelectron spectroscopy increased from 0.4 to 0.8. The integration of sulphite directly into steam pretreatment resulted in the solubilisation of 60% of the lignin while more than 80% of the carbohydrate present in the original substrate was recovered in the water insoluble fraction after Na2CO3 addition. More than 80% of the sugars present in the original cellulose and xylan could be recovered after 48 h using an enzyme loading of 20 mg protein/g cellulose at a 10% substrate concentration. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Pulp and paper from blue agave waste from tequila production.

    Science.gov (United States)

    Idarraga, G; Ramos, J; Zuñiga, V; Sahin, T; Young, R A

    1999-10-01

    Pulping of blue agave waste, from the production of tequila, was evaluated by both chemical and biomechanical pulping processes. Two conventional and two organosolv systems were used to pulp the agave waste under a standard set of conditions. The soda-ethanol process was superior in terms of delignification and pulp properties in comparison to the soda and ethanol organosolv processes for pulping of agave waste; however, the kraft process gave the best strength properties. In general, the strength of the agave waste pulps was rather poor in comparison to wood and other agro-based pulps; however, the tear strength was relatively high. This result is typical of poorly bonded sheets and may be due to the coarseness of the agave fibers and/or loss of hemicelluloses in the steaming process for the tequila production. Fungal treatment of the agave waste with Ceriporiopsis subvermispora reduced the energy consumption for mechanical refining but gave biomechanical pulps with inferior strength properties. The blue agave chemical pulps should be suitable for blending with softwood kraft pulps for publication grade paper.

  9. STUDIES ON HIBISCUS CANNABINUS, HIBISCUS SABDARIFFA, AND CANNABINUS SATIVA PULP TO BE A SUBSTITUTE FOR SOFTWOOD PULP- PART 1: AS-AQ DELIGNIFICATION PROCESS

    OpenAIRE

    Dharm Dutt; J. S. Upadhyaya; C. H. Tyagi

    2010-01-01

    Hibiscus cannabinus, Hibiscus sabdariffa, and Cannabinus sativa, which are renewable non-woody fiber resources having characteristics similar to that of softwood (bast fibers), when used together with hardwood (core fibers), gave higher pulp yield with good mechanical strength properties when using an alkaline sulphite-anthraquinone (AS-AQ) pulping process rather than a conventional kraft pulping process and bleached more readily than kraft and soda pulps with a CEHH bleaching sequence. A com...

  10. Degradation kinetics and mechanism of trace nitrobenzene by granular activated carbon enhanced microwave/hydrogen peroxide system.

    Science.gov (United States)

    Tan, Dina; Zeng, Honghu; Liu, Jie; Yu, Xiaozhang; Liang, Yanpeng; Lu, Lanjing

    2013-07-01

    The kinetics of the degradation of trace nitrobenzene (NB) by a granular activated carbon (GAC) enhanced microwave (MW)/hydrogen peroxide (H202) system was studied. Effects of pH, NB initial concentration and tert-butyl alcohol on the removal efficiency were examined. It was found that the reaction rate fits well to first-order reaction kinetics in the MW/GAC/H202 process. Moreover, GAC greatly enhanced the degradation rate of NB in water. Under a given condition (MW power 300 W, H202 dosage 10 mg/L, pH 6.85 and temperature (60 +/- 5)degrees C), the degradation rate of NB was 0.05214 min-1when 4 g/L GAC was added. In general, alkaline pH was better for NB degradation; however, the optimum pH was 8.0 in the tested pH value range of 4.0-12.0. At H202 dosage of 10 mg/L and GAC dosage of 4 g/L, the removal of NB was decreased with increasing initial concentrations of NB, indicating that a low initial concentration was beneficial for the degradation of NB. These results indicated that the MW/GAC/H202 process was effective for trace NB degradation in water. Gas chromatography-mass spectrometry analysis indicated that a hydroxyl radical addition reaction and dehydrogenation reaction enhanced NB degradation.

  11. Pulping and paper properties of Palmyra palm fruit fibers

    Directory of Open Access Journals (Sweden)

    Waranyou Sridach

    2010-05-01

    Full Text Available Palmyra palm fruit fibers have the properties to be used as an alternative raw material of cellulosic pulps for papermaking.Acid and alkali pulping were investigated by using nitric acid and caustic soda on a laboratory scale, with the purpose of producing printing or writing grade pulp. The chemical composition of fiber strands from palmyra palm fruits were examined, such as holocellulose, cellulose, pentosan, lignin and extractives. The yields of acid and soda pulps were below 40%. The main physical and mechanical properties of hand sheets produced from acid and soda processes were evaluated on 80 g/m2 test sheets as functions of the following parameters: tensile index, tear index, and brightness. The mechanical properties of soda pulps were developed by twin-roll press while it was not necessary to fibrillate acidic pulps through the beating step. The soda pulp sheets presented a lower brightness than that of acidic pulp sheets. The mechanicaland physical properties of the acidic and alkaline pulps verified that they were of an acceptable quality for papermaking.

  12. Influence of the mechanical environment on the engineering of mineralised tissues using human dental pulp stem cells and silk fibroin scaffolds.

    Directory of Open Access Journals (Sweden)

    Anna Woloszyk

    Full Text Available Teeth constitute a promising source of stem cells that can be used for tissue engineering and regenerative medicine purposes. Bone loss in the craniofacial complex due to pathological conditions and severe injuries could be treated with new materials combined with human dental pulp stem cells (hDPSCs that have the same embryonic origin as craniofacial bones. Optimising combinations of scaffolds, cells, growth factors and culture conditions still remains a great challenge. In the present study, we evaluate the mineralisation potential of hDPSCs seeded on porous silk fibroin scaffolds in a mechanically dynamic environment provided by spinner flask bioreactors. Cell-seeded scaffolds were cultured in either standard or osteogenic media in both static and dynamic conditions for 47 days. Histological analysis and micro-computed tomography of the samples showed low levels of mineralisation when samples were cultured in static conditions (0.16±0.1 BV/TV%, while their culture in a dynamic environment with osteogenic medium and weekly µCT scans (4.9±1.6 BV/TV% significantly increased the formation of homogeneously mineralised structures, which was also confirmed by the elevated calcium levels (4.5±1.0 vs. 8.8±1.7 mg/mL. Molecular analysis of the samples showed that the expression of tooth correlated genes such as Dentin Sialophosphoprotein and Nestin were downregulated by a factor of 6.7 and 7.4, respectively, in hDPSCs when cultured in presence of osteogenic medium. This finding indicates that hDPSCs are able to adopt a non-dental identity by changing the culture conditions only. Also an increased expression of Osteocalcin (1.4x and Collagen type I (1.7x was found after culture under mechanically dynamic conditions in control medium. In conclusion, the combination of hDPSCs and silk scaffolds cultured under mechanical loading in spinner flask bioreactors could offer a novel and promising approach for bone tissue engineering where appropriate and

  13. Influence of the mechanical environment on the engineering of mineralised tissues using human dental pulp stem cells and silk fibroin scaffolds.

    Science.gov (United States)

    Woloszyk, Anna; Holsten Dircksen, Sabrina; Bostanci, Nagihan; Müller, Ralph; Hofmann, Sandra; Mitsiadis, Thimios A

    2014-01-01

    Teeth constitute a promising source of stem cells that can be used for tissue engineering and regenerative medicine purposes. Bone loss in the craniofacial complex due to pathological conditions and severe injuries could be treated with new materials combined with human dental pulp stem cells (hDPSCs) that have the same embryonic origin as craniofacial bones. Optimising combinations of scaffolds, cells, growth factors and culture conditions still remains a great challenge. In the present study, we evaluate the mineralisation potential of hDPSCs seeded on porous silk fibroin scaffolds in a mechanically dynamic environment provided by spinner flask bioreactors. Cell-seeded scaffolds were cultured in either standard or osteogenic media in both static and dynamic conditions for 47 days. Histological analysis and micro-computed tomography of the samples showed low levels of mineralisation when samples were cultured in static conditions (0.16±0.1 BV/TV%), while their culture in a dynamic environment with osteogenic medium and weekly µCT scans (4.9±1.6 BV/TV%) significantly increased the formation of homogeneously mineralised structures, which was also confirmed by the elevated calcium levels (4.5±1.0 vs. 8.8±1.7 mg/mL). Molecular analysis of the samples showed that the expression of tooth correlated genes such as Dentin Sialophosphoprotein and Nestin were downregulated by a factor of 6.7 and 7.4, respectively, in hDPSCs when cultured in presence of osteogenic medium. This finding indicates that hDPSCs are able to adopt a non-dental identity by changing the culture conditions only. Also an increased expression of Osteocalcin (1.4x) and Collagen type I (1.7x) was found after culture under mechanically dynamic conditions in control medium. In conclusion, the combination of hDPSCs and silk scaffolds cultured under mechanical loading in spinner flask bioreactors could offer a novel and promising approach for bone tissue engineering where appropriate and rapid bone

  14. Dental pulp stem cells

    DEFF Research Database (Denmark)

    Ashri, N. Y.; Ajlan, S. A.; Aldahmash, Abdullah M.

    2015-01-01

    scaffold, and guided through signaling molecules. Dental pulp stem cells have been used in an increasing number of studies in dental tissue engineering. Those cells show mesenchymal (stromal) stem cell-like properties including self-renewal and multilineage differentiation potentials, aside from...... an updated review on dental pulp stem cells and their applications in periodontal regeneration, in combination with different scaffolds and growth factors....

  15. Application of resin in pulp technique for ion exchange separation of uranium from alkaline leachate

    International Nuclear Information System (INIS)

    Sreenivas, T.; Rajan, K.; Chakravorty, J.

    2014-01-01

    The hydrometallurgical process for the recovery of uranium from different ores uses ion exchange (IX) technique for the separation of dissolved uranium values. Conventionally, the IX process is carried out on leach solution obtained after the filtration or counter-current decantation of the leach slurries. Amongst the two types of leach pulps generated in uranium ore processing, viz acidic and alkaline, the latter one consists of predominantly fine-size pulps of higher viscosity, thus making the solid-liquid separation an arduous task. Sustained research for improvising the efficiency of various unit operations in the uranium process flowsheet have resulted in advent of new generation resins which are mechanically re-silent, posses higher exchange capacity thereby enabling separation of dissolved uranium ions from the leach pulps directly. Some of the prominent low-grade uranium ore deposits in India are hosted in acid consuming gangue matrix. These ore deposits necessitate fine grinding as well as application of alkaline leaching for the dissolution of uranium values. The leach pulps analyse 500 – 600 mg/l of U3O8 and contain total dissolved solutes (TDS) to the extent of about 50 g/l. Analysis of the characteristics of the leach pulp indicated suitability of resin-in-pulp technique for the separation of uranyl carbonate anions from the leachate. This paper describes the results of the RIP test work on alkaline leach slurry using various commercially available strong base anionic exchange resins. Parametric variation studies were conducted to establish the adsorption isotherm and sorption kinetics followed by elution of loaded uranium. Based on these results semi-continuous experiments on “carousel” mode were carried out. The results indicate superiority of gel type polystyrene based resins grafted with quaternary ammonium ion in comparison to the macro-porous resins. Semi-continuous counter-current extraction and elution tests indicated that about 98% of

  16. Proteomic analysis of human tooth pulp: proteomics of human tooth.

    Science.gov (United States)

    Eckhardt, Adam; Jágr, Michal; Pataridis, Statis; Mikšík, Ivan

    2014-12-01

    The unique pulp-dentin complex demonstrates strong regenerative potential, which enables it to respond to disease and traumatic injury. Identifying the proteins of the pulp-dentin complex is crucial to understanding the mechanisms of regeneration, tissue calcification, defense processes, and the reparation of dentin by dental pulp. The lack of knowledge of these proteins limits the development of more efficient therapies. The proteomic profile of human tooth pulp was investigated and compared with the proteome of human dentin and blood. The samples of tooth pulp were obtained from 5 sound permanent human third molars of 5 adults (n = 5). The extracted proteins were separated by 2-dimensional gel electrophoresis, analyzed by nano-liquid chromatography tandem mass spectrometry, and identified by correlating mass spectra to the proteomic databases. A total of 342 proteins were identified with high confidence, and 2 proteins were detected for the first time in an actual human sample. The identified tooth pulp proteins have a variety of functions: structural, catalytic, transporter, protease activity, immune response, and many others. In a comparison with dentin and blood plasma, 140 (pulp/dentin) shared proteins were identified, 37 of which were not observed in plasma. It can be suggested that they might participate in the unique pulp-dentin complex. This proteomic investigation of human tooth pulp, together with the previously published study of human dentin, is one of the most comprehensive proteome lists of human teeth to date. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  17. The mechanism of action of lymphokines. IX. The enzymatic basis of hydrogen peroxide production by lymphokine-activated macrophages.

    Science.gov (United States)

    Freund, M; Pick, E

    1986-08-15

    The purpose of this study was to elucidate the biochemical basis of the enhanced hydrogen peroxide (H2O2) production by guinea pig peritoneal macrophages (MP) cultured in lymphokine (LK)-containing medium. The markedly augmented H2O2 generation by these cells, demonstrable by the horseradish peroxidase (HRP)-catalyzed oxidation of phenol red, is distinguished by its lack of dependence on a second stimulus. We demonstrate that H2O2 production is truly spontaneous and is not caused by a stimulant present among the H2O2 assay reagents. The principal candidate for such a role was HRP type II (a mixture of five isoenzymes) that was reported to be capable of eliciting an oxidative burst in MP. Four distinct HRP isoenzymes that were found incapable of provoking an oxidative response were nevertheless adequate for demonstrating H2O2 production by LK-activated MP. Blocking the MP receptor for mannose by the addition of mannan to the assay system resulted in enhanced detection of H2O2 by low concentrations of HRP type II and by three out of four HRP isoenzymes. Treatment of MP with LK-containing medium for 72 hr did not result in a significant change in the activity of cellular superoxide dismutase (SOD) compared with MP cultured for the same length of time in control medium. By using the specific inhibitor of copper, zinc-containing SOD, sodium diethyldithiocarbamate (DDC), and the universal SOD inhibitor, sodium nitroprusside, we found that the predominant enzyme in guinea pig peritoneal MP is probably manganese-containing SOD. Incubation of LK-activated MP with nitroprusside resulted in almost total inhibition of H2O2 production and a simultaneous switch to superoxide (O2-) liberation. Similar exposure to DDC had no effect. These data indicate that H2O2 produced by LK-activated MP is derived exclusively by enzymatic dismutation of O2- mediated by a manganese-containing SOD. The increase in spontaneous H2O2 production induced by LK is therefore secondary to augmented O2

  18. Simultaneous production of bio-ethanol and bleached pulp from red algae.

    Science.gov (United States)

    Yoon, Min Ho; Lee, Yoon Woo; Lee, Chun Han; Seo, Yung Bum

    2012-12-01

    The red algae, Gelidium corneum, was used to produce bleached pulp for papermaking and ethanol. Aqueous extracts obtained at 100-140 °C were subjected to saccharification, purification, fermentation, and distillation to produce ethanol. The solid remnants were bleached with chlorine dioxide and peroxide to make pulp. In the extraction process, sulfuric acid and sodium thiosulfate were added to increase the extract yield and to improve de-polymerization of the extracts, as well as to generate high-quality pulp. An extraction process incorporating 5% sodium thiosulfate by dry weight of the algae provided optimal production conditions for the production of both strong pulp and a high ethanol yield. These results suggest that it might be possible to utilize algae instead of trees and starch for pulp and ethanol production, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. Biogas generation apple pulp.

    Science.gov (United States)

    Llaneza Coalla, H; Blanco Fernández, J M; Morís Morán, M A; López Bobo, M R

    2009-09-01

    In view of the pressing problem that appears in our region (Asturias, north of Spain) with the residues from the cider production, it was decided to test this kind of material as a co-substrate joint with slaughterhouse waste in a laboratory unit. The anaerobic digestion of apple pulp was investigated for biogas production. This paper presents the results where apple pulp was co-digested with slaughterhouse waste (pig intestine and bovine stomach content) in a biogas laboratory unit (10 l CSTR reactor). The production of biogas has reached very satisfactory values during the whole test (0.8m(3)kg(-1)OTS), verifying that the process is kept in stable conditions of pH (near 8.0), and the volatile fatty acids was always underneath 3000 mg/l, when the pulp amount was lower than 100g in mesophilic conditions. The fat concentration into the digester remained always below the value that causes inhibition of the methanogenic bacteria, 500 mg/l. Finally, methane concentration (77-80%) and H(2)S concentration (400 ppm) in the biogas, they were similar to those obtained when the test was run out in the absence of apple pulp. The process efficiency with respect to COD removal was high, near 80% of the total COD. Finally, inhibitory effects of methanogenic bacteria were observed when pulp concentration was around 10% in the input material.

  20. Epigenetic regulation in dental pulp inflammation

    Science.gov (United States)

    Hui, T; Wang, C; Chen, D; Zheng, L; Huang, D; Ye, L

    2016-01-01

    Dental caries, trauma, and other possible factors could lead to injury of the dental pulp. Dental infection could result in immune and inflammatory responses mediated by molecular and cellular events and tissue breakdown. The inflammatory response of dental pulp could be regulated by genetic and epigenetic events. Epigenetic modifications play a fundamental role in gene expression. The epigenetic events might play critical roles in the inflammatory process of dental pulp injury. Major epigenetic events include methylation and acetylation of histones and regulatory factors, DNA methylation, and small non-coding RNAs. Infections and other environmental factors have profound effects on epigenetic modifications and trigger diseases. Despite growing evidences of literatures addressing the role of epigenetics in the field of medicine and biology, very little is known about the epigenetic pathways involved in dental pulp inflammation. This review summarized the current knowledge about epigenetic mechanisms during dental pulp inflammation. Progress in studies of epigenetic alterations during inflammatory response would provide opportunities for the development of efficient medications of epigenetic therapy for pulpitis. PMID:26901577

  1. Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Lei Hu

    2017-01-01

    Full Text Available Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental pulp ECM from swine and evaluated whether it could mediate pulp regeneration. Dental pulps were acquired from the mandible anterior teeth of swine 12 months of age and decellularized with 10% sodium dodecyl sulfate (SDS combined with Triton X-100. Pulp regeneration was conducted by seeding human dental pulp stem cells into decellularized pulp and transplanted subcutaneously into nude mice for 8 weeks. The decellularized pulp demonstrated preserved natural shape and structure without any cellular components. Histological analysis showed excellent ECM preservation and pulp-like tissue, and newly formed mineralized tissues were regenerated after being transplanted in vivo. In conclusion, decellularized swine dental pulp maintains ECM components favoring stem cell proliferation and differentiation, thus representing a suitable scaffold for improving clinical outcomes and functions of teeth with dental pulp diseases.

  2. Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration.

    Science.gov (United States)

    Hu, Lei; Gao, Zhenhua; Xu, Junji; Zhu, Zhao; Fan, Zhipeng; Zhang, Chunmei; Wang, Jinsong; Wang, Songlin

    2017-01-01

    Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM) is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental pulp ECM from swine and evaluated whether it could mediate pulp regeneration. Dental pulps were acquired from the mandible anterior teeth of swine 12 months of age and decellularized with 10% sodium dodecyl sulfate (SDS) combined with Triton X-100. Pulp regeneration was conducted by seeding human dental pulp stem cells into decellularized pulp and transplanted subcutaneously into nude mice for 8 weeks. The decellularized pulp demonstrated preserved natural shape and structure without any cellular components. Histological analysis showed excellent ECM preservation and pulp-like tissue, and newly formed mineralized tissues were regenerated after being transplanted in vivo. In conclusion, decellularized swine dental pulp maintains ECM components favoring stem cell proliferation and differentiation, thus representing a suitable scaffold for improving clinical outcomes and functions of teeth with dental pulp diseases.

  3. Mucoid conversion of Pseudomonas aeruginosa by hydrogen peroxide: a mechanism for virulence activation in the cystic fibrosis lung

    DEFF Research Database (Denmark)

    Mathee, Kalai; Ciofu, Oana; Sternberg, Claus

    1999-01-01

    leukocytes (PMNs), which release free oxygen radicals such as H(2)O(2) The mucoid phenotype among the strains infecting CF patients indicates overproduction of a linear polysaccharide called alginate. To mimic the inflammatory environment of the CF lung, P. aeruginosa PAO1, a typical non-mucoid strain....... These findings indicate that gene activation in bacteria by toxic oxygen radicals, similar to that found in plants and mammalian cells, may serve as a defence mechanism for the bacteria. This suggests that mucoid conversion is a response to oxygen radical exposure and that this response is a mechanism of defence...... by the bacteria. This is the first report to show that PMNs and their oxygen radicals can cause this phenotypic and genotypic change which is so typical of the intractable form of P. aeruginosa in the CF lung. These findings may provide a basis for the development of anti-oxidant and anti-inflammatory therapy...

  4. Possible involvement of membrane lipids peroxidation and oxidation of catalytically essential thiols of the cerebral transmembrane sodium pump as component mechanisms of iron-mediated oxidative stress-linked dysfunction of the pump's activity

    Directory of Open Access Journals (Sweden)

    T.I. Omotayo

    2015-04-01

    Full Text Available The precise molecular events defining the complex role of oxidative stress in the inactivation of the cerebral sodium pump in radical-induced neurodegenerative diseases is yet to be fully clarified and thus still open. Herein we investigated the modulation of the activity of the cerebral transmembrane electrogenic enzyme in Fe2+-mediated in vitro oxidative stress model. The results show that Fe2+ inhibited the transmembrane enzyme in a concentration dependent manner and this effect was accompanied by a biphasic generation of aldehydic product of lipid peroxidation. While dithiothreitol prevented both Fe2+ inhibitory effect on the pump and lipid peroxidation, vitamin E prevented only lipid peroxidation but not inhibition of the pump. Besides, malondialdehyde (MDA inhibited the pump by a mechanism not related to oxidation of its critical thiols. Apparently, the low activity of the pump in degenerative diseases mediated by Fe2+ may involve complex multi-component mechanisms which may partly involve an initial oxidation of the critical thiols of the enzyme directly mediated by Fe2+ and during severe progression of such diseases; aldehydic products of lipid peroxidation such as MDA may further exacerbate this inhibitory effect by a mechanism that is likely not related to the oxidation of the catalytically essential thiols of the ouabain-sensitive cerebral electrogenic pump.

  5. A Histopathological Study of Direct Pulp Capping with Adhesive Resins

    Directory of Open Access Journals (Sweden)

    J. Salhenejad

    2004-12-01

    Full Text Available Statement of Problem: Recently, it has been proposed that different adhesive materials can be used for direct pulp capping. Previous studies have demonstrated that multi steps dentin adhesives could form reparative dentin similar to calcium hydroxide (CH.Purpose: The aim of this study was to evaluate the histological pulp response of ninety mechanically exposed cat pulps to two adhesive resins (Scotch Bond MP and Single Bond 3M were compared with a calcium hydroxide cement (Dycal, Dentsply.Materials and Methods : Class V facial cavities with similar pulpal exposures were prepared in canines. In the experimental groups phosphoric acid was used to etch the enamel and dentin and pulp exposure, and after it dentin adhesives was applied. The exposure point of the control group was capped with Dycal then the remainder of the cavities was etched and a dentin adhesive (single bond was applied. All of the cavities were restored with a composite resin (Z 100 in usual manner. The animals were scarified after 7, 30 and 60 days (n=30, and the pulp evaluated histologically, statistical analysis was carried out with Kruskal- Wallis test (a=0.05.Results: The data showed that most of the cases had mild inflammation of pulp tissue.There was no significant difference in inflammatory reaction of pulp by Dycal and two adhesive systems, severe inflammatory reaction of pulp was observed only in most of the 30- day Single Bond group. Soft tissue organization of dentin bridge was less than ScotchBond and Dycal groups, the differentiation of dentin bridge was less than Scotch Bond group after 7 days.Conclusion: Slight inflammatory cell infiltration was the main reaction of exposed pulp when two commercially available adhesive resins were placed directly on the exposed pulp.There was no significant difference in inflammatory reaction of pulp between Dycal and two adhesive systems after 7 days and 60 days. After 7 days most of the specimens showed an amount of predentin

  6. Hydrogen peroxide safety issues

    International Nuclear Information System (INIS)

    Conner, W.V.

    1993-01-01

    A literature survey was conducted to review the safety issues involved in handling hydrogen peroxide solutions. Most of the information found in the literature is not directly applicable to conditions at the Rocky Flats Plant, but one report describes experimental work conducted previously at Rocky Flats to determine decomposition reaction-rate constants for hydrogen peroxide solutions. Data from this report were used to calculate decomposition half-life times for hydrogen peroxide in solutions containing several decomposition catalysts. The information developed from this survey indicates that hydrogen peroxide will undergo both homogeneous and heterogeneous decomposition. The rate of decomposition is affected by temperature and the presence of catalytic agents. Decomposition of hydrogen peroxide is catalyzed by alkalies, strong acids, platinum group and transition metals, and dissolved salts of transition metals. Depending upon conditions, the consequence of a hydrogen peroxide decomposition can range from slow evolution of oxygen gas to a vapor, phase detonation of hydrogen peroxide vapors

  7. Kinetics and mechanisms of the oxidation of alcohols and hydroxylamines by hydrogen peroxide, catalyzed by methyltrioxorhenium, MTO, and the oxygen binding properties of cobalt Schiff base complexes

    Energy Technology Data Exchange (ETDEWEB)

    Zauche, Timothy [Iowa State Univ., Ames, IA (United States)

    1999-02-12

    Catalysis is a very interesting area of chemistry, which is currently developing at a rapid pace. A great deal of effort is being put forth by both industry and academia to make reactions faster and more productive. One method of accomplishing this is by the development of catalysts. Enzymes are an example of catalysts that are able to perform reactions on a very rapid time scale and also very specifically; a goal for every man-made catalyst. A kinetic study can also be carried out for a reaction to gain a better understanding of its mechanism and to determine what type of catalyst would assist the reaction. Kinetic studies can also help determine other factors, such as the shelf life of a chemical, or the optimum temperature for an industrial scale reaction. An area of catalysis being studied at this time is that of oxygenations. Life on this earth depends on the kinetic barriers for oxygen in its various forms. If it were not for these barriers, molecular oxygen, water, and the oxygenated materials in the land would be in a constant equilibrium. These same barriers must be overcome when performing oxygenation reactions on the laboratory or industrial scale. By performing kinetic studies and developing catalysts for these reactions, a large number of reactions can be made more economical, while making less unwanted byproducts. For this dissertation the activation by transition metal complexes of hydrogen peroxide or molecular oxygen coordination will be discussed.

  8. Reaction Mechanisms and Structural and Physicochemical Properties of Caffeic Acid Grafted Chitosan Synthesized in Ascorbic Acid and Hydroxyl Peroxide Redox System.

    Science.gov (United States)

    Liu, Jun; Pu, Huimin; Chen, Chong; Liu, Yunpeng; Bai, Ruyu; Kan, Juan; Jin, Changhai

    2018-01-10

    The ascorbic acid (AA) and hydroxyl peroxide (H 2 O 2 ) redox pair induced free radical grafting reaction is a promising approach to conjugate phenolic groups with chitosan (CS). In order to reveal the exact mechanisms of the AA/H 2 O 2 redox pair induced grafting reaction, free radicals generated in the AA/H 2 O 2 redox system were compared with hydroxyl radical ( • OH) produced in the Fe 2+ /H 2 O 2 redox system. Moreover, the structural and physicochemical properties of caffeic acid grafted CS (CA-g-CS) synthesized in these two redox systems were compared. Results showed that only ascorbate radical (Asc •- ) was produced in the AA/H 2 O 2 system. The reaction between Asc •- and CS produced novel carbon-centered radicals, whereas no new free radicals were detected when • OH reacted with CS. Thin layer chromatography, UV-vis, Fourier transform infrared, and nuclear magnetic resonance spectroscopic analyses all confirmed that CA was successfully grafted onto CS through Asc •- . However, CA could be hardly grafted onto CS via • OH. CA-g-CS synthesized through Asc •- exhibited lower thermal stability and crystallinity than the reaction product obtained through • OH. For the first time, our results demonstrated that the synthesis of CA-g-CS in the AA/H 2 O 2 redox system was mediated by Asc •- rather than • OH.

  9. Dual Mechanism of an Intramolecular Charge Transfer (ICT)-FRET-Based Fluorescent Probe for the Selective Detection of Hydrogen Peroxide.

    Science.gov (United States)

    Liang, Xiao; Xu, Xiaoyi; Qiao, Dan; Yin, Zheng; Shang, Luqing

    2017-12-14

    A dual-mechanism intramolecular charge transfer (ICT)-FRET fluorescent probe for the selective detection of H 2 O 2 in living cells has been designed and synthesized. This probe used a coumarin-naphthalimide hybrid as the FRET platform and a boronate moiety as the recognition group. Upon the addition of H 2 O 2 , the probe exhibited a redshifted (73 nm) fluorescence emission, and the ratio of fluorescence intensities at λ=558 and 485 nm (F 558 /F 485 ) shifted notably (up to 100-fold). Moreover, there was a good linearity (R 2 =0.9911) between the ratio and concentration of H 2 O 2 in the range of 0 to 60 μm, with a limit of detection of 0.28 μm (signal to noise ratio (S/N)=3). This probe could also detect enzymatically generated H 2 O 2 . Importantly, it could be used to visualize endogenous H 2 O 2 produced by stimulation from epidermal growth factor. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Biomechanical pulping of kenaf

    Science.gov (United States)

    Aziz Ahmed; Masood Akhtar; Gary C. Myers; Gary M. Scott

    1999-01-01

    The objective of this study was to investigate the effect of fungal pretreatment of whole kenaf prior to refining on refiner electrical energy consumption, paper strength, and optical properties. We also explored the suitability of whole kenaf biomechanical pulp for making newsprint in terms of ISO brightness and strength properties. Kenaf was sterilized by autoclaving...

  11. Infection and Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Sahng G. Kim

    2016-03-01

    Full Text Available The regeneration of the pulp-dentin complex has been a great challenge to both scientists and clinicians. Previous work has shown that the presence of prior infection may influence the characteristics of tissues formed in the root canal space after regenerative endodontic treatment. The formation of ectopic tissues such as periodontal ligament, bone, and cementum has been observed in the root canal space of immature necrotic teeth with apical periodontitis, while the regeneration of dentin and pulp has been identified in previously non-infected teeth. The current regenerative endodontic therapy utilizes disinfection protocols, which heavily rely on chemical irrigation using conventional disinfectants. From a microbiological point of view, the current protocols may not allow a sufficiently clean root canal microenvironment, which is critical for dentin and pulp regeneration. In this article, the significance of root canal disinfection in regenerating the pulp-dentin complex, the limitations of the current regenerative endodontic disinfection protocols, and advanced disinfection techniques designed to reduce the microorganisms and biofilms in chronic infection are discussed.

  12. Production of uranium peroxide

    International Nuclear Information System (INIS)

    Caropreso, F.E.; Kreuz, D.F.

    1977-01-01

    A process is claimed of recovering uranium values as uranium peroxide from an aqueous uranyl solution containing dissolved vanadium and sodium impurities by treating the uranyl solution with hydrogen peroxide in an amount sufficient to have an excess of at least 0.5 parts H 2 O 2 per part of vanadium (V 2 O 5 ) above the stoichiometric amount required to form the uranium peroxide, the hydrogen peroxide treatment is carried out in three sequential phases consisting of I, a precipitation phase in which the hydrogen peroxide is added to the uranyl solution to precipitate the uranium peroxide and the pH of the reaction medium maintained in the range of 2.5 to 5.5 for a period of from about 1 to 60 minutes after the hydrogen peroxide addition; II, a digestion phase in which the pH of the reaction medium is maintained in the range of 3.0 to 7.0 for a period of about 5 to 180 minutes and III, a final phase in which the pH of the reaction medium is maintained in the range of 4.0 to 7.0 for a period of about 1 to 60 minutes during which time the uranium peroxide is separated from the reaction solution containing the dissolved vanadium and sodium impurities. The excess hydrogen peroxide is maintained during the entire treatment up until the uranium peroxide is separated from the reaction medium

  13. Sisal organosolv pulp as reinforcement for cement based composites

    Directory of Open Access Journals (Sweden)

    Ana Paula Joaquim

    2009-09-01

    Full Text Available The present work describes non-conventional sisal (Agave sisalana chemical (organosolv pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP fibres were produced by the slurry de-watering and pressing method as a crude simulation of the Hatschek process. Composites were evaluated at 28 days of age, after exposition to accelerated carbonation and after 100 soak/dry cycles. Composites containing organosolv pulp presented lower mechanical strength, water absorption and apparent porosity than composites reinforced with kraft pulp. The best mechanical performance after ageing was also achieved by samples reinforced with kraft pulp. The addition of PP fibres favoured the maintenance of toughness after ageing. Accelerated carbonation promoted the densification of the composites reinforced with sisal organosolv + PP fibres.

  14. Antioxidant activity of citrullus colocynthis pulp extract in the RBC's of alloxan-induced diabetic rats

    International Nuclear Information System (INIS)

    Dallak, M.; Jaliah, B.I.

    2010-01-01

    Previous studies in our laboratory showed that Citrullus colocynthis pulp seedless extract have antihyperglycemic and insulinotropic effects in alloxan induced diabetes. Reactive oxygen species have been implicated in the mechanism of damage of red blood cells and anaemia in diabetic patients. So the current study was carried out to investigate the protective role of citrullus colocynthis against oxidative stress in the RBC's of alloxan induced diabetic rats. Methods: Rats were divided into four groups each of ten rats, the first group was normal non diabetic rats given normal saline orally and was named control group, the second group was diabetic rats given normal saline orally and were named normal saline treated-diabetic rats, the third and fourth group were diabetic rats treated with the pulp extract or glibenclamide (a positive control) orally. Evaluations were made for haematological parameters in the blood and for lipid peroxidation and oxidative stress enzymes activities in the RBC's of all experimental rats. Results: The diabetic rats had a significant decrease (p<0.05) in total erythrocytes count and Packed Cell Volume (PCV) and a normal Haemoglobin (Hb) value in the blood. They also showed decreased levels of Thiobarbituric Acid Reactive Substances (TBARS) and decreased activities of Superoxide Dismutase (SOD) and Catalase (CAT) in the RBC's hemolysate. On other hand, oral administration of citrullus colocynthis or glibenclamide alleviated these altered parameters in the treated rats, they resulted in a significant increase (p<0.05) in the in total erythrocytes count and PCV (Haematocrit) values in the blood and caused a significant decreased levels of TBARS and increased activities of SOD and CAT in the RBC's of those diabetic treated rats when compared to diabetic rats given normal saline. The effect was more profound in citrullus colocynthis treated diabetic rats. Conclusion: Citrullus colocynthis pulp extract possesses a potent antioxidant property

  15. Mechanism of hydrogen peroxide dismutation by a dimanganese catalase mimic: dominant role of an intramolecular base on substrate binding affinity and rate acceleration.

    Science.gov (United States)

    Boelrijk, A E; Dismukes, G C

    2000-07-10

    Several modifications of the manganese coordination environment and oxidation states of a family of synthetic dimanganese complexes have been introduced in search of the structural features that promote high rates of hydrogen peroxide dismutation (catalase activity). The X-ray structure of reduced catalase (T thermophilus) reveals a dimanganese(II,II) site linked by three bridges: mu 13-glutamate-, mu-OH-, and mu-OH2. The roles of a bridging hydroxide vs mu-aqua and the carboxylate have been examined in the reduced Mn2(II,II) complexes, [(L1,2)Mn2(mu-O2CCH3)(mu-X)]2+ for X- = OH- (7A) or X = H2O (1-4), and their oxidized Mn2(III,III) analogues, [(L1,2)Mn2(mu-O)(O2CCH3)(OH)]+ (6) (L1 is N,N,N',N'-tetrakis(2-methylenebenzamidazolyl)-1,3-diaminopropan- 2-ol, and L2 is the tetrakis-N-ethylated analogue of L1, which has all amine protons replaced by ethyl groups). The steady-state catalase rate is first-order in concentration of both substrate and reduced catalyst and saturates at high peroxide concentrations in all cases, confirming peroxide/catalyst complex formation. No catalyst decomposition is seen after > 2000 turnovers. Catalysis proceeds via a ping-pong mechanism between the Mn2(II,II/III,III) redox states, involving complexes 6 and 7A/7A'. The Mn2(III,IV) oxidation state was not active in catalase activity. Replacement of the mu-aqua bridge by mu-hydroxide eliminates a kinetic lag phase in production of the O2 product, increases the affinity for substrate peroxide in the rate-limiting step as seen by a 5-fold. decrease in the Michaelis constant (KM), and accelerates the maximum rate (kcat) by 65-fold The kinetic and spectroscopic data are consistent with substrate deprotonation by the hydroxide bridge, yielding a hydroperoxyl bridge coordinated between the Mn ions (mu, eta 2 geometry, "end-on") as the basis for catalysis: mu-OH- + H2O2-->mu-O2H- + H2O. Binding of a second hydroxide ion to 7A causes a further increase in kcat by 4-fold with no further change in

  16. The number of bleaching sessions influences pulp tissue damage in rat teeth.

    Science.gov (United States)

    Cintra, Luciano Tavares Angelo; Benetti, Francine; da Silva Facundo, Aguinaldo Cândido; Ferreira, Luciana Louzada; Gomes-Filho, João Eduardo; Ervolino, Edilson; Rahal, Vanessa; Briso, André Luiz Fraga

    2013-12-01

    Hydrogen peroxide tooth bleaching is claimed to cause alterations in dental tissue structures. This study investigated the influence of the number of bleaching sessions on pulp tissue in rats. Male Wistar rats were studied in 5 groups (groups 1S-5S) of 10 each, which differed by the number (1-5) of bleaching sessions. In each session, the animals were anesthetized, and 35% hydrogen peroxide gel was applied to 3 upper right molars. Two days after the experimental period, the animals were killed, and their jaws were processed for light microscope evaluation. Pulp tissue reactions were scored as follows: 1, no or few inflammatory cells and no reaction; 2, session, necrotic tissue in the pulp horns and underlying inflammatory changes were observed. The extent and intensity of these changes increased with the number of bleaching sessions. After 5 sessions, the changes included necrotic areas in the pulp tissue involving the second third of the radicular pulp and intense inflammation in the apical third. The number of bleaching sessions directly influenced the extent of pulp damage. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  17. Antioxidant capacity of Kraft black liquor from the pulp and paper industry.

    Science.gov (United States)

    Perez-Perez, Elizabeth; Rodríguez-Malaver, Antonio J

    2005-07-01

    The effect of Kraft black liquor on the lipid peroxidation of rat homogenates was examined. The lipid peroxidation of homogenates from different organs (kidney, brain, lung, and liver) was induced by Fenton's reagent. The products of lipid peroxidation, lipid hydroperoxides and TBARS were measured by FOX method and TBA assay, respectively. It was found that black liquor significantly reduced the concentration of TBARS, but not the concentration of lipid hydroperoxides. This inhibition was directly proportional to the concentration of Kraft black liquor and the incubation temperature. Conclusively, the black liquor from pulp and paper industry exhibited an antioxidant activity.

  18. Fungal biomass production from coffee pulp juice

    Energy Technology Data Exchange (ETDEWEB)

    De Leon, R.; Calzada, F.; Herrera, R.; Rolz, C.

    1980-01-01

    Coffee pulp or skin represents about 40% of the weight of the fresh coffee fruit. It is currently a waste and its improper handling creates serious pollution problems for coffee producing countries. Mechanical pressing of the pulp will produce two fractions: coffee pulp juice (CPJ) and pressed pulp. Aspergillus oryzae, Trichoderma harzianum, Penicillium crustosum and Gliocladium deliquescens grew well in supplemented CPJ. At shake flask level the optimum initial C/N ratio was found to be in the range of 8 to 14. At this scale, biomass values of up to 50 g/l were obtained in 24 hours. Biomass production and total sugar consumption were not significantly different to all fungal species tested at the bench-scale level, even when the initial C/N ratio was varied. Best nitrogen consumption values were obtained when the initial C/N ratio was 12. Maximum specific growth rates occurred between 4-12 hours for all fungal species tested. (Refs. 8).

  19. Pulp-Capping with Mineral Trioxide Aggregate

    Directory of Open Access Journals (Sweden)

    Peycheva Kalina

    2015-11-01

    Full Text Available There are two considerations for direct pulp capping - accidental mechanical pulp exposure and exposure caused by caries. Mineral trioxide aggregate (MTA was used as pulp-capping material to preserve the vitality of the pulpal tissues. Follow-up examinations revealed that treatment was successful in preserving pulpal vitality and continued development of the tooth. On the basis of available information, it appears that MTA is the material of choice for some clinical applications. Material and methods: Cases 18 - 8 teeth with grey MTA, 10 teeth with white MTA; diagnose: Pulpitis chronica ulcerosa, Electro pulpal test (EOD - 30-35 μA, pre-clinical X-ray - without changes in the structures, follow ups for 4 years. Successful treatments: without clinical symptoms and changes in the X-rays: 5 teeth with grey MTA, 8 teeth with white MTA for period of 4 years. Unsuccessful treatments: Clinical symptoms and sometimes changes in the X-ray: 3 with grey MTA, 2 with white MTA. MTA is an appropriate material for pulp-capping and follow-up examinations revealed that the treatment was successful in preserving pulpal vitality.

  20. The problem of peroxidation in radiolis logy

    International Nuclear Information System (INIS)

    Baraboj, V.A.; Chebotarev, E.E.

    1986-01-01

    A hypothesis is validated concerning the products of freeradical oxidation of lipids and the phenol compounds as a mediator of the stress-syndrome. The data are reviewed on activation of peroxidation under the effect of radiation, cytochemical agents, etc., secondarily stimulating the neurohumoral system function of homeostasis regulation. With the emotional-algesic and cold-stresses, the regulatory system stimulation is of primary, reflex, nature, but it secondarily promotes the peroxidation activation. The radiotoxins (of the quinoid and lipid nature) appearing in tissues under the effect of ionizing radiation, are smilar in structure and mechanism of action to peroxidation activation products formed under the effect of other stress-agents

  1. Inorganic precursor peroxides for antifouling coatings

    DEFF Research Database (Denmark)

    Olsen, S.M.; Pedersen, L.T.; Hermann, M.H.

    2009-01-01

    Modern antifouling coatings are generally based on cuprous oxide (Cu2O) and organic biocides as active ingredients. Cu2O is prone to bioaccumulation, and should therefore be replaced by more environmentally benign compounds when technically possible. However, cuprous oxide does not only provide...... antifouling properties, it is also a vital ingredient for the antifouling coating to obtain its polishing and leaching mechanism. In this paper, peroxides of strontium, calcium, magnesium, and zinc are tested as pigments in antifouling coatings. The peroxides react with seawater to create hydrogen peroxide...... matrix provides antifouling properties exceeding those of a similar coating based entirely on zinc oxide....

  2. Influence of Alkaline-Peroxide Treatment of Fiber on the Mechanical Properties of Oil Palm Mesocarp Fiber/Poly(butylene succinate Biocomposite

    Directory of Open Access Journals (Sweden)

    Yoon Yee Then

    2015-01-01

    Full Text Available In this work, the surface of oil palm mesocarp fiber (OPMF was modified via alkaline-peroxide treatment with hydrogen peroxide under alkaline conditions. The effect of the treatment on the chemical composition and microstructure of the fiber was examined using chemical analysis, Fourier transform infrared (FTIR spectroscopy, scanning electron microscopy (SEM, and X-ray diffraction (XRD analysis. The treatment resulted in the removal of lignin, hemicellulose, and waxy substances from the fiber and increased its surface roughness and crystallinity. The eco-friendly biocomposite was made from poly(butylene succinate (PBS and chemically treated fiber at a weight ratio of 30:70, and was fabricated via a melt-blending technique followed by hot-pressed moulding. The results indicated that alkaline-peroxide treatment of the fiber improved the tensile strength, tensile modulus, and elongation at break of the OPMF/PBS biocomposite by 54, 830, and 43%, respectively. The SEM analysis revealed improvement of the interfacial adhesion between the chemically treated fiber and the PBS. This work demonstrates that alkaline-peroxide treatment of fiber is beneficial prior to its use in fabricating biocomposites.

  3. Peroxides and radiation impairment of oxidative phosphorylation

    Energy Technology Data Exchange (ETDEWEB)

    Dovgii, I E; Akoev, I G

    1975-09-01

    An increase in the peroxidase activity of the mitochondria and a simultaneous rise in the amount of peroxide compounds, which are half lipid-like substances, are detected within the first 10 minutes after irradiation (1000 r). A mechanism of radiation impairment of oxidative phosphorylation is connected with the penetration of its inhibitors to the mitochondria due to the disturbed permeability of membranes affected by peroxides.

  4. Isolation and characterization of lignocellulose nanofibers from different wheat straw pulps.

    Science.gov (United States)

    Sánchez, Rafael; Espinosa, Eduardo; Domínguez-Robles, Juan; Loaiza, Javier Mauricio; Rodríguez, Alejandro

    2016-11-01

    Wheat straw was cooked under different pulping processes: Soda (100°C, 7% NaOH, 150min), Kraft (170°C, 16% alkalinity, 25% sulfidity, 40min) and Organosolv (210°C, 60% ethanol, 60min). Once the pulps were obtained, lignocellulose nanofibers (LCNF) were isolated by mechanical process and TEMPO-mediated oxidation followed by a high pressure homogenization. After pulping process, the different pulps were characterized and its chemical composition was determined. The pulps characterization indicates that the Soda process is the process that, despite producing less delignification, retains much of the hemicelluloses in the pulp, being this content a key factor in the nanofibrillation process. Regarding the LCNF obtained by mechanical process, those nanofibers isolated from Organosolv wheat pulp (OWP) and Kraft wheat pulp (KWP) show low values for nanofibrillation yield, specific surface area and greater diameter. However, those nanofibers isolated from Soda wheat pulp (SWP) reach much higher values for these parameters and presents a diameter of 14nm, smaller than those obtained by TEMPO-mediated oxidation from OWP. Smaller diameters are generally obtained in TEMPO-oxidized LCNF. This work concludes that the lignin content does not affect greatly to obtain LCNF as does the hemicellulose content, so it is accurate to use a soft pulping process. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. STORAGE OF CHEMICALLY PRETREATED WHEAT STRAW – A MEANS TO ENSURE QUALITY RAW MATERIAL FOR PULP PREPARATION

    Directory of Open Access Journals (Sweden)

    Terttu Heikkilä

    2010-07-01

    Full Text Available The aim of this study was to evaluate effects of chemical pretreatment and storage on non-wood pulping and on pulp quality. The processes studied were hot water treatment followed by alkaline peroxide bleaching or soda cooking. The results showed that it is possible to store wheat straw outside for at least one year without significant changes in the raw material chemical composition and without adverse effects on the resulting pulp quality. The results are significant to the industry using non-woods to ensure the availability and the quality of the raw-material throughout the year in spite of the short harvesting time.

  6. Effects of the bleaching sequence on the optical brighteners action in eucalyptus kraft pulp

    Directory of Open Access Journals (Sweden)

    Mauro Manfredi

    2014-06-01

    Full Text Available During the bleaching process the pulp is treated with chemical reagents that can be retained in the pulp and interfere in the action of the optical brighteners. Different bleaching sequences can produce pulps at the same brightness but with different potential to whiteness increase when treated with optical brighteners. The objective of this study was to evaluate the influence of the bleaching sequence on the efficiency of disulphonated and tetrasulphonated optical brighteners. Eucalyptus kraft pulp was bleached using four different bleaching sequences. For each pulp three brightness targets were aimeds. For each bleaching sequence mathematical model was generated for predicting the final pulp whiteness according to the initial brightness and the optical brightener charge applied. The presence of organochlorine residues in the pulp reduced the effectiveness of the optical brighteners. Therefore, bleaching sequences that use low chlorine dioxide charge favors for greater gains in whiteness with the application of optical brighteners. The replacement of the final chlorine dioxide bleaching stage with a hydrogen peroxide one in the sequence increased the efficiency of the optical brightening agents.

  7. Alkaline pulping with additives of date palm rachis and leaves from Sudan.

    Science.gov (United States)

    Khristova, P; Kordsachia, O; Khider, T

    2005-01-01

    Soda-anthraquinone (soda-AQ), alkaline sulphite-anthraquinone (AS-AQ) and alkaline sulphite-anthraquinone-methanol (ASAM) pulping of date palm rachis and leaves from Sudan was carried under different conditions, and pulps with variable yields and mechanical properties were obtained. The date palm rachis gave best yields and mechanical properties with the AS-AQ or the ASAM process, while the leaves were best pulped with the soda method with low yield, but very good strength properties. Blending with 10% and 30% kenaf bark pulp was beneficial, especially for the AS-AQ pulps. Totally chlorine free (TCF) bleached rachis pulps were obtained of high brightness and strength properties suitable for use in writing and printing papers.

  8. Durability of pulp fiber-cement composites

    Science.gov (United States)

    Mohr, Benjamin J.

    Wood pulp fibers are a unique reinforcing material as they are non-hazardous, renewable, and readily available at relatively low cost compared to other commercially available fibers. Today, pulp fiber-cement composites can be found in products such as extruded non-pressure pipes and non-structural building materials, mainly thin-sheet products. Although natural fibers have been used historically to reinforce various building materials, little scientific effort has been devoted to the examination of natural fibers to reinforce engineering materials until recently. The need for this type of fundamental research has been emphasized by widespread awareness of moisture-related failures of some engineered materials; these failures have led to the filing of national- and state-level class action lawsuits against several manufacturers. Thus, if pulp fiber-cement composites are to be used for exterior structural applications, the effects of cyclical wet/dry (rain/heat) exposure on performance must be known. Pulp fiber-cement composites have been tested in flexure to examine the progression of strength and toughness degradation. Based on scanning electron microscopy (SEM), environmental scanning electron microscopy (ESEM), energy dispersive spectroscopy (EDS), a three-part model describing the mechanisms of progressive degradation has been proposed: (1) initial fiber-cement/fiber interlayer debonding, (2) reprecipitation of crystalline and amorphous ettringite within the void space at the former fiber-cement interface, and (3) fiber embrittlement due to reprecipitation of calcium hydroxide filling the spaces within the fiber cell wall structure. Finally, as a means to mitigate kraft pulp fiber-cement composite degradation, the effects of partial portland cement replacement with various supplementary cementitious materials (SCMs) has been investigated for their effect on mitigating kraft pulp fiber-cement composite mechanical property degradation (i.e., strength and toughness

  9. The Anti-Inflammatory Effect of Human Telomerase-Derived Peptide on P. gingivalis Lipopolysaccharide-Induced Inflammatory Cytokine Production and Its Mechanism in Human Dental Pulp Cells

    Directory of Open Access Journals (Sweden)

    Yoo-Jin Ko

    2015-01-01

    Full Text Available Porphyromonas gingivalis is considered with inducing pulpal inflammation and has lipopolysaccharide (LPS as an inflammatory stimulator. GV1001 peptide has anticancer and anti-inflammation activity due to inhibiting activation of signaling molecules after penetration into the various types of cells. Therefore, this study examined inhibitory effect of GV1001 on dental pulp cells (hDPCs stimulated by P. gingivalis LPS. The intracellular distribution of GV1001 was analyzed by confocal microscopy. Real-time RT-PCR was performed to determine the expression levels of TNF-α and IL-6 cytokines. The role of signaling by MAP kinases (ERK and p38 was explored using Western blot analysis. The effect of GV1001 peptide on hDPCs viability was measured by MTT assay. GV1001 was predominantly located in hDPC cytoplasm. The peptide inhibited P. gingivalis LPS-induced TNF-α and IL-6 production in hDPCs without significant cytotoxicity. Furthermore, GV1001 treatment markedly inhibited the phosphorylation of MAP kinases (ERK and p38 in LPS-stimulated hDPCs. GV1001 may prevent P. gingivalis LPS-induced inflammation of apical tissue. Also, these findings provide mechanistic insight into how GV1001 peptide causes anti-inflammatory actions in LPS-stimulated pulpitis without significantly affecting cell viability.

  10. On the Mechanism of Cytoprotection by Ferrostatin-1 and Liproxstatin-1 and the Role of Lipid Peroxidation in Ferroptotic Cell Death

    OpenAIRE

    Zilka, Omkar; Shah, Ron; Li, Bo; Friedmann Angeli, Jos? Pedro; Griesser, Markus; Conrad, Marcus; Pratt, Derek A.

    2017-01-01

    Ferroptosis is a form of regulated necrosis associated with the iron-dependent accumulation of lipid hydroperoxides that may play a key role in the pathogenesis of degenerative diseases in which lipid peroxidation has been implicated. High-throughput screening efforts have identified ferrostatin-1 (Fer-1) and liproxstatin-1 (Lip-1) as potent inhibitors of ferroptosis ? an activity that has been ascribed to their ability to slow the accumulation of lipid hydroperoxides. Herein we demonstrate t...

  11. Avoiding total reduced sulfur (TRS) emissions from sodium sulfite pulping recovery processes

    International Nuclear Information System (INIS)

    Norman, J.C.; Sell, N.J.; Ciriacks, J.C.

    1990-01-01

    This paper reports that one of the current trends in paper-making with cellulose pulping is the use of high-yield processes. With yields greater than 65%, these processes include mechanical pulps (groundwood and thermomechanical pulps or TMP), and semichemical types (chemi-TMP or CTMP). Groundwood and TMP make up about 10% of North American pulp production. Semichemical pulp makes up about 7% and is mostly used for corrugating medium. High-yield pulping for linerboard, particularly using the alkaline sulfite process, is also likely to be used in the future. High-yield pulping is based primarily on the sulfite process using mostly sodium-based chemicals. A disadvantage of this process is the unavailability of a recovery system for the inorganic pulping chemicals. Generally, mills have not accepted any particular recovery system for this process. For this and other reasons, sulfite processes constitute only 3-4% of the total North American pulp production. If high-yield processes continue to increase in popularity, a sodium sulfite chemical recovery system will be needed. A number of chemical recovery systems have been developed in the past 30 years for sodium-based sulfite pulping processes, with most of the mills successfully using this process located in Scandinavia

  12. Is Pulp Inflammation a Prerequisite for Pulp Healing and Regeneration?

    Directory of Open Access Journals (Sweden)

    Michel Goldberg

    2015-01-01

    Full Text Available The importance of inflammation has been underestimated in pulpal healing, and in the past, it has been considered only as an undesirable effect. Associated with moderate inflammation, necrosis includes pyroptosis, apoptosis, and nemosis. There are now evidences that inflammation is a prerequisite for pulp healing, with series of events ahead of regeneration. Immunocompetent cells are recruited in the apical part. They slide along the root and migrate toward the crown. Due to the high alkalinity of the capping agent, pulp cells display mild inflammation, proliferate, and increase in number and size and initiate mineralization. Pulp fibroblasts become odontoblast-like cells producing type I collagen, alkaline phosphatase, and SPARC/osteonectin. Molecules of the SIBLING family, matrix metalloproteinases, and vascular and nerve mediators are also implicated in the formation of a reparative dentinal bridge, osteo/orthodentin closing the pulp exposure. Beneath a calciotraumatic line, a thin layer identified as reactionary dentin underlines the periphery of the pulp chamber. Inflammatory and/or noninflammatory processes contribute to produce a reparative dentinal bridge closing the pulp exposure, with minute canaliculi and large tunnel defects. Depending on the form and severity of the inflammatory and noninflammatory processes, and according to the capping agent, pulp reactions are induced specifically.

  13. OPTICAL PROPERTY ANALYSIS OF THERMALLY AND PHOTOLYTICALLY AGED EUCALYPTUS CAMALDULENSIS CHEMITHERMOMECHANICAL PULP (CTMP

    Directory of Open Access Journals (Sweden)

    Yao Chen,

    2012-02-01

    Full Text Available To investigate the optical properties of chemithermomechanical pulp (CTMP from Eucalyptus camaldulensis, one group of samples of CTMP was aged by heating, and another group was first subjected to bleaching with different bleaching agents, and then aging by exposure to sunlight. Chromophores were analyzed using diffuse reflectance UV-Vis spectra (DRUV, and the brightness and color parameters (L*, a*, b* were analyzed using colorimetry. Results showed that the color reactions of the pulp, upon heating, were enhanced in the presence of moisture. There was a linear relationship between the pulp initial moisture content (MC and the intensity of UV-Vis absorption. The contribution of different chromophores to pulp color was analyzed with the help of bleaching agents: hydrogen peroxide, sodium dithionite, and sodium borohydride. Sodium borohydride and hydrogen peroxide treatments resulted in a decrease in the absorption band at 280 nm along with the shoulder near 320 nm, which could be attributed to conjugated C=O and C=C systems. Similarly, sodium dithionite treatment also led to a decrease in absorption of the carbonyls and double bonds conjugated with aromatic double bonds. The chromaticity parameters of bleached pulp increased after exposure to sunlight. A correspondingly higher concentration of quinoid structures was found.

  14. PRODUCTION OF PRINTING AND WRITING PAPER GRADE PULP FROM ELEPHANT GRASS

    Directory of Open Access Journals (Sweden)

    Marcela Freitas Andrade

    2016-09-01

    Full Text Available The main goal of this study was to characterize chemically and morphologically elephant grass (Pennisetum purpureum, and evaluate the potential of its fibers for production of printing and writing paper grade pulp. The elephant grass was chemically and morphologically characterized and cooked by the soda process to two different degrees of delignification (kappa 17.5 and 10.6. The resulting pulps were fully bleached by the O-D*-(EP-D sequence and characterized for their beatability, drainability and physical-mechanical properties. The lignin content (20.2% was low, indicating that this grass should be easier to pulp. The morphological analyses of the elephant grass indicated a short fiber material, similar to hardwoods. The soda pulp from elephant grass cooked to kappa number 17.5 presented higher screened yield than 10.6 kappa pulp, with alkali demands of 15.0% and 20.0%, respectively. The total active chlorine required by the 17.5 and 10.6 kappa pulps, were 42.1 and 35.1 kg/odt pulp, respectively, to achieve an ISO brightness of approximately 90.0%. The bleached soda pulps cooked to 17.5 and 10.6 kappa number showed similar refinability and resistance to drainage, but the tensile and burst index were highest for the 17.5 kappa pulp at beating energy consumptions in the range of 0-6 Wh. It was concluded that both 10.6 and 17.5 kappa pulps from elephant grass are suitable for the production of printing and writing paper grade pulps, but the highest kappa 17.5 pulp is more economically attractive given its highest pulping yield, despite the significantly increased of chemical demand for bleaching A produção de papel para impressão e escrita Grau de celulose a partir de capim-elefante.

  15. Chapter 6: Prehydrolysis Pulping with Fermentation Coproducts

    Science.gov (United States)

    T.H. Wegner; C.J. Houtman; A.W. Rudie; B.L. Illman; P.J. Ince; E.M. Bilek; T.W. Jeffries

    2013-01-01

    Although the term “integrateed biorefinery” is new, the concept has long been familiar to the pulp and paper industry, where processes include biomass boilers providing combined heat and power, and byproducts of pulping include turpentine, fatty acids and resin acids. In the dominant kraft (or sulfate) pulping process, dissolved lignin and chemicals from the pulp...

  16. Factors affecting the optimal performance of a high-yield pulping operation

    Energy Technology Data Exchange (ETDEWEB)

    Broderick, G [Noranda Technology Centre, Pointe-Claire, PQ (Canada); Paris, J [Ecole Polytechnique, Montreal, PQ (Canada); Valada, J L [Quebec Univ., Trois-Rivieres, PQ (Canada)

    1995-06-01

    Strategies for operating a chemical-mechanical pulp mill were investigated from data based on process models from some one hundred pilot scale pulping runs. Optimal values for 55 process and pulp quality variables have been calculated by applying a genetic algorithm search to a fuzzy model of the overall system. Best pulp quality was achieved and maintained when the chemical pretreatment was conducted at moderately low temperatures using a high SO{sub 2} concentration, which produced high sulphonation and high yield at the same time. By characterizing the quality of the pulp at the fibre level, optimization results were said to be more easily transferable to other high yield pulping systems. 19 refs., 6 tabs.

  17. Degumming Pretreatment with Sodium Hydroxide and Sodium Oxalate in the Process of Whole Cotton Stalk APMP Pulping

    Directory of Open Access Journals (Sweden)

    Yu-Meng Zhao

    2015-03-01

    Full Text Available The effect of degumming pretreatment on whole cotton stalk alkaline peroxide mechanical pulp (APMP was researched. Degumming pretreatment was used as the first stage of an APMP pulping process, replacing conventional hot water pretreatment. Two degumming agents of sodium hydroxide (NaOH and sodium oxalate (Na2C2O4 were researched separately. The efficiency of hot water pretreatment, NaOH pretreatment, and Na2C2O4 pretreatment on pectin and metal ions removal was compared. After pretreatment of hot water, NaOH, and Na2C2O4, pectin content was reduced to 4.0%, 2.1%, 1.6%, respectively, compared to original material (4.3%, at removal rates of 7%, 51%, and 64%, respectively. For metal ions, especially transition metal ions, the removal rate was up to 20% after degumming pretreatment. The brightness of the handsheets was 64% ISO, 68% ISO, and 73% ISO, respectively. The dirt count was 2674 mm2•m-2, 533 mm2•m-2, and 132 mm2•m-2, respectively. After Na2C2O4 pretreatment, the tension index and tear index were increased to 40.5 N•m•g-1 and 4.5 mN•m2•g-1, respectively. Through degumming pretreatment, pectin, metal ions, and dirt count were reduced efficiently, and the brightness and physical strength were improved significantly.

  18. Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration

    OpenAIRE

    Hu, Lei; Gao, Zhenhua; Xu, Junji; Zhu, Zhao; Fan, Zhipeng; Zhang, Chunmei; Wang, Jinsong; Wang, Songlin

    2017-01-01

    Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM) is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental p...

  19. Dentin and pulp sense cold stimulus.

    Science.gov (United States)

    Tokuda, Masayuki; Tatsuyama, Shoko; Fujisawa, Mari; Morimoto-Yamashita, Yoko; Kawakami, Yoshiko; Shibukawa, Yoshiyuki; Torii, Mistuso

    2015-05-01

    Dentin hypersensitivity is a common symptom, and recent convergent evidences have reported transient receptor potential (TRP) channels in odontoblasts act as mechanical and thermal molecular sensor, which detect stimulation applied on the exposed dentin surface, to drive multiple odontoblastic cellular functions, such as sensory transduction and/or dentin formation. In the present study, we confirmed expression of TRP melastatin subfamily member-8 (TRPM8) channels in primary cultured cells derived from human dental pulp cells (HPCs) and mouse odontoblast-lineage cells (OLCs) as well as in dentin matrix protein-1 (DMP-1) and dentin sialoprotein (DSP) positive acutely isolated rat odontoblasts from dental pulp tissue slice culture by immunohistochemical analyses. In addition, we detected TRPM8 channel expression on HPCs and OLCs by RT-PCR and Western blotting analyses. These results indicated that both odontoblasts and dental pulp cells express TRPM8 channels in rat, mouse and human, and therefore we hypothesize they may contribute as cold sensor in tooth. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Protein oxidation and peroxidation

    DEFF Research Database (Denmark)

    Davies, Michael Jonathan

    2016-01-01

    Proteins are major targets for radicals and two-electron oxidants in biological systems due to their abundance and high rate constants for reaction. With highly reactive radicals damage occurs at multiple side-chain and backbone sites. Less reactive species show greater selectivity with regard...... to the residues targeted and their spatial location. Modification can result in increased side-chain hydrophilicity, side-chain and backbone fragmentation, aggregation via covalent cross-linking or hydrophobic interactions, protein unfolding and altered conformation, altered interactions with biological partners...... and modified turnover. In the presence of O2, high yields of peroxyl radicals and peroxides (protein peroxidation) are formed; the latter account for up to 70% of the initial oxidant flux. Protein peroxides can oxidize both proteins and other targets. One-electron reduction results in additional radicals...

  1. Protective effects of Arctium lappa L. roots against hydrogen peroxide-induced cell injury and potential mechanisms in SH-SY5Y cells.

    Science.gov (United States)

    Tian, Xing; Guo, Li-Ping; Hu, Xiao-Long; Huang, Jin; Fan, Yan-Hua; Ren, Tian-Shu; Zhao, Qing-Chun

    2015-04-01

    Accumulated evidence has shown that excessive reactive oxygen species (ROS) have been implicated in neuronal cell death related with various chronic neurodegenerative disorders. This study was designed to explore neuroprotective effects of ethyl acetate extract of Arctium lappa L. roots (EAL) on hydrogen peroxide (H2O2)-induced cell injury in human SH-SY5Y neuroblastoma cells. The cell viability was significantly decreased after exposure to 200 μM H2O2, whereas pretreatment with different concentrations of EAL attenuated the H2O2-induced cytotoxicity. Hoechst 33342 staining indicated that EAL reversed nuclear condensation in H2O2-treated cells. Meanwhile, TUNEL assay with DAPI staining showed that EAL attenuated apoptosis was induced by H2O2. Pretreatment with EAL also markedly elevated activities of antioxidant enzyme (GSH-Px and SOD), reduced lipid peroxidation (MDA) production, prevented ROS formation, and the decrease of mitochondrial membrane potential. In addition, EAL showed strong radical scavenging ability in 2,2'-azino-bis(3-ethylbenzthiazoline-6-sulfonic acid) assays. Furthermore, EAL inhibited H2O2-induced apoptosis by increases in the Bcl-2/Bax ratio, decreases in cytochrome c release, and attenuation of caspase-3, caspase-9 activities, and expressions. These findings suggest that EAL may be regarded as a potential antioxidant agent and possess potent neuroprotective activity against H2O2-induced injury.

  2. Alkaline Peroxide Delignification of Corn Stover

    Energy Technology Data Exchange (ETDEWEB)

    Mittal, Ashutosh [Biosciences; Katahira, Rui [National; Donohoe, Bryon S. [Biosciences; Black, Brenna A. [National; Pattathil, Sivakumar [Complex; Stringer, Jack M. [National; Beckham, Gregg T. [National

    2017-05-30

    Selective biomass fractionation into carbohydrates and lignin is a key challenge in the conversion of lignocellulosic biomass to fuels and chemicals. In the present study, alkaline hydrogen peroxide (AHP) pretreatment was investigated to fractionate lignin from polysaccharides in corn stover (CS), with a particular emphasis on the fate of the lignin for subsequent valorization. The influence of peroxide loading on delignification during AHP pretreatment was examined over the range of 30-500 mg H2O2/g dry CS at 50 degrees C for 3 h. Mass balances were conducted on the solid and liquid fractions generated after pretreatment for each of the three primary components, lignin, hemicellulose, and cellulose. AHP pretreatment at 250 mg H2O2/g dry CS resulted in the pretreated solids with more than 80% delignification consequently enriching the carbohydrate fraction to >90%. Two-dimensional nuclear magnetic resonance (2D-NMR) spectroscopy of the AHP pretreated residue shows that, under high peroxide loadings (>250 mg H2O2/g dry CS), most of the side chain structures were oxidized and the aryl-ether bonds in lignin were partially cleaved, resulting in significant delignification of the pretreated residues. Gel permeation chromatography (GPC) analysis shows that AHP pretreatment effectively depolymerizes CS lignin into low molecular weight (LMW) lignin fragments in the aqueous fraction. Imaging of AHP pretreated residues shows a more granular texture and a clear lamellar pattern in secondary walls, indicative of layers of varying lignin removal or relocalization. Enzymatic hydrolysis of this pretreated residue at 20 mg/g of glucan resulted in 90% and 80% yields of glucose and xylose, respectively, after 120 h. Overall, AHP pretreatment is able to selectively remove more than 80% of the lignin from biomass in a form that has potential for downstream valorization processes and enriches the solid pulp into a highly digestible material.

  3. A survey of chemicals inducing lipid peroxidation in biological systems.

    Science.gov (United States)

    Kappus, H

    1987-01-01

    A great number of drugs and chemicals are reviewed which have been shown to stimulate lipid peroxidation in any biological system. The underlying mechanisms, as far as known, are also dealt with. Lipid peroxidation induced by iron ions, organic hydroperoxides, halogenated hydrocarbons, redox cycling drugs, glutathione depleting chemicals, ethanol, heavy metals, ozone, nitrogen dioxide and a number of miscellaneous compounds, e.g. hydrazines, pesticides, antibiotics, are mentioned. It is shown that lipid peroxidation is stimulated by many of these compounds. However, quantitative estimates cannot be given yet and it is still impossible to judge the biological relevance of chemical-induced lipid peroxidation.

  4. On the Mechanism of Cytoprotection by Ferrostatin-1 and Liproxstatin-1 and the Role of Lipid Peroxidation in Ferroptotic Cell Death.

    Science.gov (United States)

    Zilka, Omkar; Shah, Ron; Li, Bo; Friedmann Angeli, José Pedro; Griesser, Markus; Conrad, Marcus; Pratt, Derek A

    2017-03-22

    Ferroptosis is a form of regulated necrosis associated with the iron-dependent accumulation of lipid hydroperoxides that may play a key role in the pathogenesis of degenerative diseases in which lipid peroxidation has been implicated. High-throughput screening efforts have identified ferrostatin-1 (Fer-1) and liproxstatin-1 (Lip-1) as potent inhibitors of ferroptosis - an activity that has been ascribed to their ability to slow the accumulation of lipid hydroperoxides. Herein we demonstrate that this activity likely derives from their reactivity as radical-trapping antioxidants (RTAs) rather than their potency as inhibitors of lipoxygenases. Although inhibited autoxidations of styrene revealed that Fer-1 and Lip-1 react roughly 10-fold more slowly with peroxyl radicals than reactions of α-tocopherol (α-TOH), they were significantly more reactive than α-TOH in phosphatidylcholine lipid bilayers - consistent with the greater potency of Fer-1 and Lip-1 relative to α-TOH as inhibitors of ferroptosis. None of Fer-1, Lip-1, and α-TOH inhibited human 15-lipoxygenase-1 (15-LOX-1) overexpressed in HEK-293 cells when assayed at concentrations where they inhibited ferroptosis. These results stand in stark contrast to those obtained with a known 15-LOX-1 inhibitor (PD146176), which was able to inhibit the enzyme at concentrations where it was effective in inhibiting ferroptosis. Given the likelihood that Fer-1 and Lip-1 subvert ferroptosis by inhibiting lipid peroxidation as RTAs, we evaluated the antiferroptotic potential of 1,8-tetrahydronaphthyridinols (hereafter THNs): rationally designed radical-trapping antioxidants of unparalleled reactivity. We show for the first time that the inherent reactivity of the THNs translates to cell culture, where lipophilic THNs were similarly effective to Fer-1 and Lip-1 at subverting ferroptosis induced by either pharmacological or genetic inhibition of the hydroperoxide-detoxifying enzyme Gpx4 in mouse fibroblasts, and glutamate

  5. Application of the MASSAHAKE-method for birch whole tree chips and for the production of raw material for mechanical pulp production; MASSAHAKE-menetelmaen soveltaminen koivulle sekae mekaanisen massan raaka-ainetuotantoon

    Energy Technology Data Exchange (ETDEWEB)

    Ahonen, M.; Seppaenen, V.; Nikala, L.

    1996-12-31

    The objectives of this project for the year 1995 were: (1) To develop the grinding process in order to decrease the wood losses in grinder, (2) To find the connection between the initial values in the process and the quality of the pulp chips, (3) To find out the behaviour of chips from mixed tree species in the MASSAHAKE process, (4) To find out the amount of knots in the pulp chips from the MASSAHAKE-process and (5) To find out the critical factors in big fuel stock made of the fuel fraction from the MASSAHAKE-process. The research with grinder was made with five different types of grinder plates. One of the blade sets was used as a reference where all the other sets were compared. In the second task a relationship between three most important initial values and the quality of pulp chips was determined. These values were: the feeding capacity of the whole tree chips to the process, the sensitivity of the optical sorter and the pixel size of bark to be removed in optical sorter. Based on the research and analysis results a linear model describing the process was made. In the third task the behaviour of mixed tree chips in the process was examined and also some full scale pulping experiments were done. Comparing the knot content of the pulp chips both from MASSAHAKE-process and normal pulp chip process a significant difference was noticed. The pulp chips from MASSAHAKE-system contained only 1/3 of the knots in normal de-barking+chipping pulp chip line. With decreased knot content a 1-3 % increase in digester capacity could be reached. Finally in fuel fraction storing research a significant dry material loss was determined

  6. Application of the MASSAHAKE-method for birch whole tree chips and for the production of raw material for mechanical pulp production; MASSAHAKE-menetelmaen soveltaminen koivulle sekae mekaanisen massan raaka-ainetuotantoon

    Energy Technology Data Exchange (ETDEWEB)

    Ahonen, M; Seppaenen, V; Nikala, L

    1997-12-31

    The objectives of this project for the year 1995 were: (1) To develop the grinding process in order to decrease the wood losses in grinder, (2) To find the connection between the initial values in the process and the quality of the pulp chips, (3) To find out the behaviour of chips from mixed tree species in the MASSAHAKE process, (4) To find out the amount of knots in the pulp chips from the MASSAHAKE-process and (5) To find out the critical factors in big fuel stock made of the fuel fraction from the MASSAHAKE-process. The research with grinder was made with five different types of grinder plates. One of the blade sets was used as a reference where all the other sets were compared. In the second task a relationship between three most important initial values and the quality of pulp chips was determined. These values were: the feeding capacity of the whole tree chips to the process, the sensitivity of the optical sorter and the pixel size of bark to be removed in optical sorter. Based on the research and analysis results a linear model describing the process was made. In the third task the behaviour of mixed tree chips in the process was examined and also some full scale pulping experiments were done. Comparing the knot content of the pulp chips both from MASSAHAKE-process and normal pulp chip process a significant difference was noticed. The pulp chips from MASSAHAKE-system contained only 1/3 of the knots in normal de-barking+chipping pulp chip line. With decreased knot content a 1-3 % increase in digester capacity could be reached. Finally in fuel fraction storing research a significant dry material loss was determined

  7. Microarray evaluation of age-related changes in human dental pulp.

    Science.gov (United States)

    Tranasi, Michelangelo; Sberna, Maria Teresa; Zizzari, Vincenzo; D'Apolito, Giuseppe; Mastrangelo, Filiberto; Salini, Luisa; Stuppia, Liborio; Tetè, Stefano

    2009-09-01

    The dental pulp undergoes age-related changes that could be ascribed to physiological, defensive, or pathological irritant-induced changes. These changes are regulated by pulp cell activity and by a variety of extracellular matrix (ECM) macromolecules, playing important roles in growth regulation, tissue differentiation and organization, formation of calcified tissue, and defense mechanisms and reactions to inflammatory stimuli. The aim of this research was to better understand the genetic changes that underlie the histological modification of the dental pulp in aging. The gene expression profile of the human dental pulp in young and older subjects was compared by RNA microarray analysis that allowed to simultaneously analyze the expression levels of thousands of genes. Data were statistically analyzed by Significance Analysis of Microarrays (SAM) Ingenuity Pathway Analysis (IPA) software. Semiquantitative and real-time reverse-transcriptase polymerase chain reaction analyses were performed to confirm the results. Microarray analysis revealed several differentially expressed genes that were categorized in growth factors, transcription regulators, apoptosis regulators, and genes of the ECM. The comparison analysis showed a high expression level of the biological functions of cell and tissue differentiation, development, and proliferation and of the immune, lymphatic, and hematologic system in young dental pulp, whereas the pathway of apoptosis was highly expressed in older dental pulp. Expression profile analyses of human dental pulp represent a sensible and useful tool for the study of mechanisms involved in differentiation, growth and aging of human dental pulp in physiological and pathological conditions.

  8. Influence of whitening gel on pulp chamber temperature rise by in-office bleaching technique

    Directory of Open Access Journals (Sweden)

    Sandro Cordeiro Loretto

    Full Text Available INTRODUCTION: Dental bleaching is a conservative method for the aesthetic restoration of stained teeth. However, whitening treatments are likely to cause adverse effects when not well planned and executed. OBJECTIVE: This study evaluated the influence of whitening gel on temperature rise in the pulp chamber, using the in-office photoactivated dental bleaching technique. MATERIAL AND METHOD: The root portion of an upper central human incisor was sectioned 3mm below the cemento-enamel junction. The root canal was enlarged to permit the insertion of the K-type thermocouple sensor (MT-401 into the pulp chamber, which was filled with thermal paste to facilitate the transfer of heat during bleaching. Three photosensitive whitening agents (35% hydrogen peroxide were used: Whiteness HP (FGM, Whiteness HP Maxx (FGM and Lase Peroxide Sensy (DMC. An LED photocuring light (Flash Lite - Discus Dental was used to activate the whitening gels. Six bleaching cycles were performed on each group tested. The results were submitted to one-way ANOVA and LSD t-test (α<0.05. RESULT: The lowest mean temperature variation (ºC was detected for Lase Peroxide Sensy (0.20, while the highest was recorded for Whiteness HP (1.50. CONCLUSION: The Whiteness HP and Whiteness HP Maxx whitening gels significantly affected the temperature rise in the pulp chamber during bleaching, and this variation was dependent on the type of whitening gel used.

  9. Evaluation of a value prior to pulping-thermomechanical pulp business concept. Part 2.

    Science.gov (United States)

    Ted Bilek; Carl Houtman; Peter Ince

    2011-01-01

    Value Prior to Pulping (VPP) is a novel biorefining concept for pulp mills that includes hydrolysis extraction of hemicellulose wood sugars and acetic acid from pulpwood prior to pulping. The concept involves conversion of wood sugars via fermentation to fuel ethanol or other chemicals and the use of remaining solid wood material in the pulping process. This paper...

  10. Engineering structural integrity issues in the pulp and paper industry

    International Nuclear Information System (INIS)

    Garner, A.; Singbeil, D.

    2002-01-01

    ESI issues for Pulp and Paper (P and P) plant are reviewed. Five typical processes are covered, namely: Chemical Pulping, Bleaching, Chemical Recovery, Mechanical Pulping and Papermaking. Equipment, chemical environments and failure modes are summarized with examples from each process. Pressure, temperature, corrosion and rotation are typical sources of risk, which is managed by appropriate inspection. The nature of the P and P Industry and its technology supply is summarized: current trends are consolidation and outsourcing. Three examples are presented to illustrate typical ESI issues: deaerator cracking where the P and P Industry alerted others to this serious cross-industry problem; pressure vessel safety factors and inconsistent international codes; and caustic cracking in continuous kraft digesters, which required rapid and concerted action to diagnose and control. In the future better predictability, data-bases, more formal risk based inspection and fitness-for-service assessments are envisaged. (author)

  11. Kraft pulping of industrial wood waste

    Science.gov (United States)

    Aziz. Ahmed; Masood. Akhtar; Gary C. Myers; Gary M. Scott

    1998-01-01

    Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

  12. Comparative pulping of sunflower stalks

    Directory of Open Access Journals (Sweden)

    Valerii Barbash

    2016-03-01

    Full Text Available The procedure of holocellulose content determination in non-wood plant raw materials was developed. The strength properties of pulp obtained from sunflower stalks by neutral-sulphite, soda, alkaline sulphite-anthraquinone-ethanol and peracetic methods of delignification were studied. Methodology of comparison of plant materials delignification methods using new lignin-carbohydrate diagram was proposed. It was shown, that the alkaline sulphite-anthraquinone-ethanol method of pulping is characterized by the highest delignification degree and is the most efficient among the studied methods

  13. Atmospheric hydrogen peroxide and organic hydroperoxides during PRIDE-PRD'06, China: their concentration, formation mechanism and contribution to secondary aerosols

    Directory of Open Access Journals (Sweden)

    W. Hua

    2008-11-01

    Full Text Available Atmospheric hydrogen peroxide (H2O2 and organic hydroperoxides were measured from 18 to 30 July in 2006 during the PRIDE-PRD'06 campaign at Backgarden, a rural site located 48 km north of Guangzhou, a mega-city in southern China. A ground-based instrument was used as a scrubbing coil collector to sample ambient air, followed by on-site analysis by high-performance liquid chromatography (HPLC coupled with post-column derivatization and fluorescence detection. The H2O2 mixing ratio over the 13 days ranged from below the detection limit to a maximum of 4.6 ppbv, with a mean (and standard deviation of (1.26±1.24 ppbv during the daytime (08:00–20:00 LT. Methyl hydroperoxide (MHP, with a maximum of 0.8 ppbv and a mean (and standard deviation of (0.28±0.10 ppbv during the daytime, was the dominant organic hydroperoxide. Other organic peroxides, including bis-hydroxymethyl hydroperoxide (BHMP, peroxyacetic acid (PAA, hydroxymethyl hydroperoxide (HMHP, 1-hydroxy-ethyl hydroperoxide (1-HEHP and ethyl hydroperoxide (EHP, were detected occasionally. The concentration of H2O2 exhibited a pronounced diurnal variation on sunny days, with a peak mixing ratio in the afternoon (12:00–18:00 LT, but lacked an explicit diurnal cycle on cloudy days. Sometimes a second peak mixing ratio of H2O2 was observed during the evening, suggesting that H2O2 was produced by the ozonolysis of alkenes. The diurnal variation profile of MHP was, in general, consistent with that of H2O2. The estimation indicated that in the morning the H2O2 detected was formed mostly through local photochemical activity, with the rest probably attributable to vertical transport. It is notable that relatively high levels of H2O2 and MHP were found in polluted air. The unexpectedly high level of HO2 radicals

  14. Atmospheric hydrogen peroxide and organic hydroperoxides during PRIDE-PRD'06, China: their concentration, formation mechanism and contribution to secondary aerosols

    Science.gov (United States)

    Hua, W.; Chen, Z. M.; Jie, C. Y.; Kondo, Y.; Hofzumahaus, A.; Takegawa, N.; Chang, C. C.; Lu, K. D.; Miyazaki, Y.; Kita, K.; Wang, H. L.; Zhang, Y. H.; Hu, M.

    2008-11-01

    Atmospheric hydrogen peroxide (H2O2) and organic hydroperoxides were measured from 18 to 30 July in 2006 during the PRIDE-PRD'06 campaign at Backgarden, a rural site located 48 km north of Guangzhou, a mega-city in southern China. A ground-based instrument was used as a scrubbing coil collector to sample ambient air, followed by on-site analysis by high-performance liquid chromatography (HPLC) coupled with post-column derivatization and fluorescence detection. The H2O2 mixing ratio over the 13 days ranged from below the detection limit to a maximum of 4.6 ppbv, with a mean (and standard deviation) of (1.26±1.24) ppbv during the daytime (08:00 20:00 LT). Methyl hydroperoxide (MHP), with a maximum of 0.8 ppbv and a mean (and standard deviation) of (0.28±0.10) ppbv during the daytime, was the dominant organic hydroperoxide. Other organic peroxides, including bis-hydroxymethyl hydroperoxide (BHMP), peroxyacetic acid (PAA), hydroxymethyl hydroperoxide (HMHP), 1-hydroxy-ethyl hydroperoxide (1-HEHP) and ethyl hydroperoxide (EHP), were detected occasionally. The concentration of H2O2 exhibited a pronounced diurnal variation on sunny days, with a peak mixing ratio in the afternoon (12:00 18:00 LT), but lacked an explicit diurnal cycle on cloudy days. Sometimes a second peak mixing ratio of H2O2 was observed during the evening, suggesting that H2O2 was produced by the ozonolysis of alkenes. The diurnal variation profile of MHP was, in general, consistent with that of H2O2. The estimation indicated that in the morning the H2O2 detected was formed mostly through local photochemical activity, with the rest probably attributable to vertical transport. It is notable that relatively high levels of H2O2 and MHP were found in polluted air. The unexpectedly high level of HO2 radicals detected in this region can account for the production of hydroperoxides, while the moderate level of NOx suppressed the formation of hydroperoxides. High concentrations of hydroperoxides were detected

  15. Insight into the mechanism revealing the peroxidase mimetic catalytic activity of quaternary CuZnFeS nanocrystals: colorimetric biosensing of hydrogen peroxide and glucose

    Science.gov (United States)

    Dalui, Amit; Pradhan, Bapi; Thupakula, Umamahesh; Khan, Ali Hossain; Kumar, Gundam Sandeep; Ghosh, Tanmay; Satpati, Biswarup; Acharya, Somobrata

    2015-05-01

    Artificial enzyme mimetics have attracted immense interest recently because natural enzymes undergo easy denaturation under environmental conditions restricting practical usefulness. We report for the first time chalcopyrite CuZnFeS (CZIS) alloyed nanocrystals (NCs) as novel biomimetic catalysts with efficient intrinsic peroxidase-like activity. Novel peroxidase activities of CZIS NCs have been evaluated by catalytic oxidation of the peroxidase substrate 3,3',5,5'-tetramethylbenzidine (TMB) in the presence of hydrogen peroxide (H2O2). CZIS NCs demonstrate the synergistic effect of elemental composition and photoactivity towards peroxidase-like activity. The quaternary CZIS NCs show enhanced intrinsic peroxidase-like activity compared to the binary NCs with the same constituent elements. Intrinsic peroxidase-like activity has been correlated with the energy band position of CZIS NCs extracted using scanning tunneling spectroscopy and ultraviolet photoelectron spectroscopy. Kinetic analyses indicate Michaelis-Menten enzyme kinetic model catalytic behavior describing the rate of the enzymatic reaction by correlating the reaction rate with substrate concentration. Typical color reactions arising from the catalytic oxidation of TMB over CZIS NCs with H2O2 have been utilized to establish a simple and sensitive colorimetric assay for detection of H2O2 and glucose. CZIS NCs are recyclable catalysts showing high efficiency in multiple uses. Our study may open up the possibility of designing new photoactive multi-component alloyed NCs as enzyme mimetics in biotechnology applications.Artificial enzyme mimetics have attracted immense interest recently because natural enzymes undergo easy denaturation under environmental conditions restricting practical usefulness. We report for the first time chalcopyrite CuZnFeS (CZIS) alloyed nanocrystals (NCs) as novel biomimetic catalysts with efficient intrinsic peroxidase-like activity. Novel peroxidase activities of CZIS NCs have been

  16. Post-translational transformation of methionine to aspartate is catalyzed by heme iron and driven by peroxide: a novel subunit-specific mechanism in hemoglobin.

    Science.gov (United States)

    Strader, Michael Brad; Hicks, Wayne A; Kassa, Tigist; Singleton, Eileen; Soman, Jayashree; Olson, John S; Weiss, Mitchell J; Mollan, Todd L; Wilson, Michael T; Alayash, Abdu I

    2014-08-08

    A pathogenic V67M mutation occurs at the E11 helical position within the heme pockets of variant human fetal and adult hemoglobins (Hb). Subsequent post-translational modification of Met to Asp was reported in γ subunits of human fetal Hb Toms River (γ67(E11)Val → Met) and β subunits of adult Hb (HbA) Bristol-Alesha (β67(E11)Val → Met) that were associated with hemolytic anemia. Using kinetic, proteomic, and crystal structural analysis, we were able to show that the Met → Asp transformation involves heme cycling through its oxoferryl state in the recombinant versions of both proteins. The conversion to Met and Asp enhanced the spontaneous autoxidation of the mutants relative to wild-type HbA and human fetal Hb, and the levels of Asp were elevated with increasing levels of hydrogen peroxide (H2O2). Using H2(18)O2, we verified incorporation of (18)O into the Asp carboxyl side chain confirming the role of H2O2 in the oxidation of the Met side chain. Under similar experimental conditions, there was no conversion to Asp at the αMet(E11) position in the corresponding HbA Evans (α62(E11)Val → Met). The crystal structures of the three recombinant Met(E11) mutants revealed similar thioether side chain orientations. However, as in the solution experiments, autoxidation of the Hb mutant crystals leads to electron density maps indicative of Asp(E11) formation in β subunits but not in α subunits. This novel post-translational modification highlights the nonequivalence of human Hb α, β, and γ subunits with respect to redox reactivity and may have direct implications to α/β hemoglobinopathies and design of oxidatively stable Hb-based oxygen therapeutics. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

  17. PEMUTIHAN PULP DENGAN HIDROGEN PEROKSIDA

    Directory of Open Access Journals (Sweden)

    Ahmad M. Fuadi

    2012-01-01

    Full Text Available The use of bleaching agent has increased as the result of increasing of paper consumption. The conventional bleaching agent that commonly used is material containing of chlorine. This material is not environmentally friendly and should be replaced by environmentally benign chemical, such as H2O2. About 40 gram of dry Akasia pulp was mixed with 600 ml of distilled water was put into plastic bag heated in a water bath. When the temperature reached 630C, a solution of 4 % of H2O2 and distilled water was added to obtain 5 % consistency. This mixture was put into water bath and was heated for 2 hours. The same procedure was conducted with various concentration of H2O2, time and pH. At the end of the process, the pulp was dewatered and washed. The filtrate obtained from the initial dewatering was used to determine the residual of H2O2. The pulp was analyzed to determine brightness, fiber strength and kappa number. The maximum achievement of brightness was 62,1 % ISO, 6.86 of kappa number and 1.02 kg/15 mm of fiber strength, which are reached at16 % of the use of H2O2, pH 11 and 5 hours of bleaching time. This achievement is similar to bleaching result by the additional of 4% H2O2. Inefficient usage of H2O2 was caused by some metal ions in the pulp which facilitate the decomposition of H2O2 to produce oxygen and water which has not effect on increasing the brightness. To improve the bleach ability of H2O2, initial treatment to remove metal ions from pulp should be done. Seiring dengan meningkatnya kebutuhan kertas, kebutuhan bahan pemutih juga mengalami kenaikan. Saat ini bahan pemutih yang banyak digunakan adalah senyawa yang mengandung khlor. Senyawa ini sangat tidak ramah lingkungan, oleh karena itu, perlu dicari bahan yang ramah lingkungan untuk menggantikannya. Salah satunya adalah hidrogen peroksida. Pulp dari pohon akasia sebanyak 40 gram kering dicampur dengan 600 ml aquadest dimasukkan dalam kantung plastik dipanaskan dalam water bath

  18. The influence of irradiation of gamma-rays on the pulping and paper making, (4)

    International Nuclear Information System (INIS)

    Suzuki, Kyoji; Inoue, Kaoru; Hanamura, Norio; Mori, Kenji

    1980-01-01

    The influence of gamma-irradiation on the beating properties of unbleached kraft pulps was studied, and the changes of the mechanical and chemical properties of the sheet made from those pulps were also investigated. The results obtained were as follows: (1) When the unbeaten pulp was treated with gamma-ray, the degree of polymerization of cellulose was decreased rapidly and the formation of aldehyde and carboxyl groups in pulp was observed in addition to that the beating time of irradiated pulps was reduced comparing with non-irradiated pulp. These effects increased roughly in proportion to the radiation dose. (2) Gamma-irradiation was more effective in wet state (moisture content = 70 - 80%) than air dry state. This may be due to the degradation products of water by gamma-irradiation. (3) The mechanical properties (breaking length, tear and burst factors) of the sheets made from irradiated pulps were considerably deteriorated at 10 7 R, but there was a slight deterioration up to 10 6 R. (4) Comparing the result of the mechanical properties, the strengths of the various sheets were shown in the following order: the sheet irradiated after paper making gt the sheet irradiated before beating (air dry state) gt the sheet irradiated before beating (wet state). (author)

  19. Davallialactone reduces inflammation and repairs dentinogenesis on glucose oxidase-induced stress in dental pulp cells.

    Science.gov (United States)

    Lee, Young-Hee; Kim, Go-Eun; Song, Yong-Beom; Paudel, Usha; Lee, Nan-Hee; Yun, Bong-Sik; Yu, Mi-Kyung; Yi, Ho-Keun

    2013-11-01

    The chronic nature of diabetes mellitus (DM) raises the risk of oral complication diseases. In general, DM causes oxidative stress to organs. This study aimed to evaluate the cellular change of dental pulp cells against glucose oxidative stress by glucose oxidase with a high glucose state. The purpose of this study was to test the antioxidant character of davallialactone and to reduce the pathogenesis of dental pulp cells against glucose oxidative stress. The glucose oxidase with a high glucose concentration was tested for hydroxy peroxide (H2O2) production, cellular toxicity, reactive oxygen species (ROS) formation, induction of inflammatory molecules and disturbance of dentin mineralization in human dental pulp cells. The anti-oxidant effect of Davallilactone was investigated to restore dental pulp cells' vitality and dentin mineralization via reduction of H2O2 production, cellular toxicity, ROS formation and inflammatory molecules. The treatment of glucose oxidase with a high glucose concentration increased H2O2 production, cellular toxicity, and inflammatory molecules and disturbed dentin mineralization by reducing pulp cell activity. However, davallialactone reduced H2O2 production, cellular toxicity, ROS formation, inflammatory molecules, and dentin mineralization disturbances even with a long-term glucose oxidative stress state. The results of this study imply that the development of oral complications is related to the irreversible damage of dental pulp cells by DM-induced oxidative stress. Davallialactone, a natural antioxidant, may be useful to treat complicated oral disease, representing an improvement for pulp vital therapy. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  20. The optimization, kinetics and mechanism of m-cresol degradation via catalytic wet peroxide oxidation with sludge-derived carbon catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yamin [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Wei, Huangzhao; Zhao, Ying [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Sun, Wenjing [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Sun, Chenglin, E-mail: clsun@dicp.ac.cn [Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China)

    2017-03-15

    Highlights: • The sludge derived carbon modified with 0 °C acid was used as catalyst in CWPO. • RSM was used to optimize CWPO reaction conditions of m-cresol for the first time. • The kinetic model was disclosed to be correlated with residue target concentration. • The proposed degradation pathways of m-cresol were well proven by DFT method. - Abstract: The sludge-derived carbon catalyst modified with 0 °C HNO{sub 3} solution was tested in catalytic wet peroxide oxidation of m-cresol (100 mg L{sup −1}) with systematical mathematical models and theoretical calculation for the first time. The reaction conditions were optimized by response surface methodology (RSM) as T = 60 °C, initial pH = 3.0, C{sub 0,H2O2(30%)} = 1.20 g L{sup −1} (lower than the stoichiometric amount of 1.80 g L{sup −1}) and C{sub cat} = 0.80 g L{sup −1}, with 96% of m-cresol and 47% of TOC converted after 16 min and 120 min of reaction, respectively, and ξ (mg TOC/g H{sub 2}O{sub 2} fed) = 83.6 mg/g. The end time of the first kinetic period in m-cresol model was disclosed to be correlated with the fixed residue m-cresol concentration of about 33%. Furthermore, the kinetic constants in models of TOC and H{sub 2}O{sub 2} exactly provide convincing proof of three-dimensional response surfaces analysis by RSM, which showed the influence of the interaction between organics and H{sub 2}O{sub 2} on effective H{sub 2}O{sub 2} utilization. The reaction intermediates over time were identified by gas chromatography–mass spectrometer based on kinetics analysis. Four degradation pathways for m-cresol were proposed, of which the possibility and feasibility were well proven by frontier molecule orbital theory and atomic charge distribution via density functional theory method.

  1. Effect of organosolv and soda pulping processes on the metals content of non-woody pulps.

    Science.gov (United States)

    González, M; Cantón, L; Rodríguez, A; Labidi, J

    2008-09-01

    In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).

  2. Melatonin attenuates inflammation of acute pulpitis subjected to dental pulp injury

    Science.gov (United States)

    Li, Ji-Guo; Lin, Jia-Ji; Wang, Zhao-Ling; Cai, Wen-Ke; Wang, Pei-Na; Jia, Qian; Zhang, An-Sheng; Wu, Gao-Yi; Zhu, Guo-Xiong; Ni, Long-Xing

    2015-01-01

    Acute pulpitis (AP), one of the most common diseases in the endodontics, usually causes severe pain to the patients, which makes the search for therapeutic target of AP essential in clinic. Toll-like receptor 4 (TLR4) signaling is widely involved in the mechanism of pulp inflammation, while melatonin has been reported to have an inhibition for a various kinds of inflammation. We hereby studied whether melatonin can regulate the expression of TLR4/NF-ĸB signaling in the pulp tissue of AP and in human dental pulp cells (HDPCs). Two left dental pulps of the adult rat were drilled open to establish the AP model, and the serum levels of melatonin and pro-inflammatory cytokines, including interleukin 1β (IL-1β), interleukin 18 (IL-18) and tumor necrosis factor α (TNF-α), were assessed at 1, 3 and 5 d post injury. At the same time points, the expression of TLR4 signaling in the pulp was explored by quantitative real-time PCR and immunohistochemistry. The AP rats were administered an abdominal injection of melatonin to assess whether melatonin rescued AP and TLR4/NF-ĸB signaling. Dental pulp injury led to an approximately five-day period acute pulp inflammation and necrosis in the pulp and a significant up-regulation of IL-1β, IL-18 and TNF-α in the serum. ELISA results showed that the level of melatonin in the serum decreased due to AP, while an abdominal injection of melatonin suppressed the increase in serum cytokines and the percentage of necrosis at the 5 d of the injured pulp. Consistent with the inflammation in AP rats, TLR4, NF-ĸB, TNF-α and IL-1β in the pulp were increased post AP compared with the baseline expression. And melatonin showed an inhibition on TLR4/NF-ĸB signaling as well as IL-1β and TNF-α production in the pulp of AP rats. Furthermore, melatonin could also regulate the expression of TLR4/NF-ĸB signaling in LPS-stimulated HDPCs. These data suggested that dental pulp injury induced AP and reduced the serum level of melatonin and that

  3. Correlation, by multivariate statistical analysis, between the scavenging capacity against reactive oxygen species and the bioactive compounds from frozen fruit pulps

    Directory of Open Access Journals (Sweden)

    Lizziane Cynara Vissotto

    2013-02-01

    Full Text Available The contents of total phenolic compounds (TPC, total flavonoids (TF, and ascorbic acid (AA of 18 frozen fruit pulps and their scavenging capacities against peroxyl radical (ROO•, hydrogen peroxide (H2O2, and hydroxyl radical (•OH were determined. Principal Component Analysis (PCA showed that TPC (total phenolic compounds and AA (ascorbic acid presented positive correlation with the scavenging capacity against ROO•, and TF (total flavonoids showed positive correlation with the scavenging capacity against •OH and ROO• However, the scavenging capacity against H2O2 presented low correlation with TF (total flavonoids, TPC (total phenolic compounds, and AA (ascorbic acid. The Hierarchical Cluster Analysis (HCA allowed the classification of the fruit pulps into three groups: one group was formed by the açai pulp with high TF, total flavonoids, content (134.02 mg CE/100 g pulp and the highest scavenging capacity against ROO•, •OH and H2O2; the second group was formed by the acerola pulp with high TPC, total phenolic compounds, (658.40 mg GAE/100 g pulp and AA , ascorbic acid, (506.27 mg/100 g pulp contents; and the third group was formed by pineapple, cacao, caja, cashew-apple, coconut, cupuaçu, guava, orange, lemon, mango, passion fruit, watermelon, pitanga, tamarind, tangerine, and umbu pulps, which could not be separated considering only the contents of bioactive compounds and the scavenging properties.

  4. 21 CFR 172.802 - Acetone peroxides.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acetone peroxides. 172.802 Section 172.802 Food and... Multipurpose Additives § 172.802 Acetone peroxides. The food additive acetone peroxides may be safely used in... acetone peroxide, with minor proportions of higher polymers, manufactured by reaction of hydrogen peroxide...

  5. Drying kinetics of atemoya pulp

    Directory of Open Access Journals (Sweden)

    Plúvia O. Galdino

    Full Text Available ABSTRACT This study was conducted in order to obtain drying curves of whole atemoya pulp through the foam-mat drying method. The suspension was prepared with whole atemoya pulp mixed with 2% of Emustab® and 2% of Super Liga Neutra® with mixing time of 20 min, and dried in a forced-air oven at different temperatures (60; 70 and 80 °C and thicknesses of the foam layer (0.5, 1.0 and 1.5 cm. The drying rate curves were plotted against the water content ratio and the semi-theoretical models of Henderson & Pabis, Page and Midilli were used. All tested models showed coefficient of determination (R2 above 0.993, and the Midilli model showed the best fit for all conditions. Drying curves were affected by temperature and layer thickness.

  6. CD44 is involved in mineralization of dental pulp cells.

    Science.gov (United States)

    Chen, Kuan-Liang; Huang, Yu-Yuan; Lung, Jrhau; Yeh, Ying-Yi; Yuan, Kuo

    2013-03-01

    CD44 is a transmembrane glycoprotein with various biological functions. Histologic studies have shown that CD44 is strongly expressed in odontoblasts at the appositional stage of tooth development. We investigated whether CD44 is involved in the mineralization of dental pulp cells. Ten human third molars with incomplete root formation were collected and processed for immunohistochemistry of CD44. Dental pulp cells isolated from another 5 human third molars were assayed for their viability, alkaline phosphatase activity, and alizarin red staining in vitro after silencing stably their expression of CD44 by using the short hairpin RNA technique. The CD44 knockdown cells were cultured on a collagen sponge and transplanted subcutaneously into the dorsal surfaces of immunocompromised mice. After 6 weeks, the subcutaneous tissues were processed for alizarin red staining and immunohistochemistry of human specific antigen. The dental pulp cells transduced with control short hairpin RNA were used as the control in all assays. CD44 is expressed in odontogenic cells with active mineral deposition during tooth development. Odontoblasts in the root ends of immature teeth express a stronger CD44 signal compared with those in the crown portion. When CD44 expression was stably suppressed in dental pulp cells, their mineralization activities were substantially decreased in both in vitro and in vivo assays. CD44 may play a crucial role in the initial mineralization of tooth-associated structures. However, further studies are required to clarify the underlying mechanisms. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  7. Preventive endodontics by direct pulp capping with restorative dentin substitute-biodentine: A series of fifteen cases

    Directory of Open Access Journals (Sweden)

    Kavita Dube

    2018-01-01

    Full Text Available Introduction: Treatment of mechanical exposure of the pulp during caries excavation presents a clinical challenge. In this case series of 15 patients, with a follow-up period of over a year, the outcome of direct pulp capping with Biodentine (septodont after mechanical pulp exposure was assessed. Aim of Study: The aim of this study is to evaluate the outcome of direct pulp capping with Biodentine in deeply carious teeth when pulp was mechanically exposed during caries excavation and cavity preparation. Vital pulps exposed during caries excavation in molar teeth were treated with 3% sodium hypochlorite for 2 min. If adequate hemostasis was achieved, the pulp tissue was capped with Biodentine, which covered the entire pulpal floor. This was followed by the placement of a layer of resin-modified glass ionomer cement and a final layer of composite resin (Filtek Z350-3M to complete the restoration. The patients were recalled periodically and evaluated for any evidence of pulpal/periapical pathology. Results: In the follow-up period that ranged from 12 to 24 months, all teeth were asymptomatic. Conclusion: Biodentine appears to be a suitable material for direct pulp capping under clinical conditions. However, long-term follow-up studies and controlled trials involving a large sample size are warranted.

  8. Histological evaluation of the pulp in teeth from dogs with naturally occurring periodontal disease.

    Science.gov (United States)

    Nemec, Ana; Pavlica, Zlatko; Stiblar-Martincic, Draga; Petelin, Milan; Erzen, Damjan; Crossley, David

    2007-12-01

    The purpose of this investigation was to evaluate the pulp of dog teeth affected by advanced periodontal disease. Histological examination was done on demineralized teeth extracted during clinical treatment of mature, client owned small and medium-size breed dogs with either good periodontal health or with advanced naturally occurring periodontal disease. Routinely stained sections from 5 clinically normal teeth and 22 teeth with advanced periodontitis from dogs between 5 and 12-years of age were examined using light microscopy. The pulp cavities of most teeth were narrow with low cellularity and some fibrosis of the pulp. Findings specific to periodontally affected teeth included acute and chronic pulpitis, vascular congestion, and pulp necrosis. A glomus body was identified in the pulp of one tooth and areas of poorly mineralized cementum were seen in both normal and diseased teeth. Age related changes in dog teeth appear similar to those reported for man and the rat. In addition to age related changes, the pulp of dog teeth with advanced periodontal disease were frequently inflamed or necrotic. This may reflect the advanced periodontitis affecting these teeth or a mechanical effect related to excessive tooth mobility. Further study is required to determine the etiology and significance of these findings and to investigate pulp status in less severely diseased teeth.

  9. An overview of the dental pulp: its functions and responses to injury.

    Science.gov (United States)

    Yu, C; Abbott, P V

    2007-03-01

    The dental pulp is a unique tissue and its importance in the long-term prognosis of the tooth is often ignored by clinicians. It is unique in that it resides in a rigid chamber which provides strong mechanical support and protection from the microbial rich oral environment. If this rigid shell loses its structural integrity, the pulp is under the threat of the adverse stimuli from the mouth, such as caries, cracks, fractures and open restoration margins, all of which provide pathways for micro-organisms and their toxins to enter the pulp. The pulp initially responds to irritation by becoming inflamed and, if left untreated, this will progress to pulp necrosis and infection. The inflammation will also spread to the surrounding alveolar bone and cause periapical pathosis. The magnitude of pulp-related problems should not be underestimated since their most serious consequence is oral sepsis, which can be life threatening, and hence correct diagnosis and management are essential. Clinicians must have a thorough understanding of the physiological and pathological features of the dental pulp as well as the biological consequences of treatment interventions.

  10. Anti-inflammatory, and antinociceptive effects of Campomanesia adamantium microencapsulated pulp

    Directory of Open Access Journals (Sweden)

    Danieli Z. Viscardi

    Full Text Available ABSTRACT Guavira fruits have antimicrobial, antioxidant, antinociceptive, and anti-inflammatory activities. Spray drying has been widely used in the food industry presenting good retention in bioactive compounds used to transform the pulp/fruit juice into powder form. Therefore, the present study has evaluated the anti-inflammatory and antinociceptive activities of the microencapsulated pulp of Campomanesia adamantium (Cambess. O.Berg, Myrtaceae, by spray drying. Different groups of mice were treated with the doses of 100 and 300 mg/kg of microencapsulated "guavira" pulp and inflammatory parameters were assessed in a carrageenan paw edema-model and leukocyte migration with pleurisy model, while the antinociceptive activity was assessed using the formalin method and CFA-induced hyperalgesia model. A significant reduction in leukocyte migration and in paw edema was observed in rodents in all time after carrageenan injection for both doses of microencapsulated pulp of C. adamantium when compared with control group. Microencapsulated pulp of C. adamantium also reduced licking time at the first (nociceptive and second (inflammatory phases in the formalin model. In CFA-induced cold and mechanical hyperalgesia, depressive behavior, and knee edema, all parameters analyzed were significantly inhibited by microencapsulated pulp of C. adamantium. Microencapsulation by spray drying proved to be a technique that promotes bioavailability and the preservation of bioactive components in guavira pulp.

  11. EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

    OpenAIRE

    Ahmad Azizi Mossello; Jalaluddin Harun; Rushdan Ibrahim; Hossien Resalati; Seyed Rashid Fallah Shamsi; Paridah Md Tahir; Mohd Nor Mohad Yusoff

    2010-01-01

    Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ) pulp of kenaf fibers versus old corrugated container (OCC) and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the h...

  12. Oxidation of lignin-carbohydrate complex from bamboo with hydrogen peroxide catalyzed by Co(salen

    Directory of Open Access Journals (Sweden)

    Zhou Xue-Fei

    2014-01-01

    Full Text Available The reactivity of salen complexes toward hydrogen peroxide has been long recognized. Co(salen was tested as catalyst for the aqueous oxidation of a refractory lignin-carbohydrate complex (LCC isolated from sweet bamboo (Dendrocalamushamiltonii in the presence of hydrogen peroxide as oxidant. Co(salen catalyzed the reaction of hydrogen peroxide with LCC. From the spectra analyses, lignin units in LCC were undergoing ring-opening, side chain oxidation, demethoxylation, β-O-4 cleavage with Co(salen catalytic oxidation. The degradation was also observed in the carbohydrate of LCC. The investigation on the refractory LCC degradation catalyzed by Co(salen may be an important aspect for environmentally-oriented biomimetic bleaching in pulp and paper industry.

  13. Diabetes induces metabolic alterations in dental pulp.

    Science.gov (United States)

    Leite, Mariana Ferreira; Ganzerla, Emily; Marques, Márcia Martins; Nicolau, José

    2008-10-01

    Diabetes can interfere in tissue nutrition and can impair dental pulp metabolism. This disease causes oxidative stress in cells and tissues. However, little is known about the antioxidant system in the dental pulp of diabetics. Thus, it would be of importance to study this system in this tissue in order to verify possible alterations indicative of oxidative stress. The aim of this study was to evaluate some parameters of antioxidant system of the dental pulp of healthy (n = 8) and diabetic rats (n = 8). Diabetes was induced by streptozotocin in rats. Six weeks after diabetes induction, a pool of the dental pulp of the 4 incisors of each rat (healthy and diabetic) was used for the determination of total protein and sialic acid concentrations and catalase and peroxidase activities. Data were compared by a Student t test (p pulps from both groups presented similar total protein concentrations and peroxidase activity. Dental pulps of diabetic rats exhibited significantly lower free, conjugated, and total sialic acid concentrations than those of control tissues. Catalase activity in diabetic dental pulps was significantly enhanced in comparison with that of control pulps. The result of the present study is indicative of oxidative stress in the dental pulp caused by diabetes. The increase of catalase activity and the reduction of sialic acid could be resultant of reactive oxygen species production.

  14. PRODUCTION OF DISSOLVING GRADE PULP FROM ALFA

    Directory of Open Access Journals (Sweden)

    Baya Bouiri

    2010-02-01

    Full Text Available Alfa, also known as Stipa tenacissimaI or “halfa”, is grown in North Africa and south Spain. Due to its short fiber length, paper made from alfa pulp retains bulk and takes block letters well. In this study alfa was evaluated for bleached pulp production. Two cellulose pulps with different chemical compositions were pulped by a conventional kraft process. One sample was taken from the original alfa material and another from alfa that had been pretreated by diluted acid. The pulp produced from the pretreated alfa was bleached by the elemental-chlorine-free sequences DEPD and DEDP. The yield, Kappa number, brightness, and α- cellulose content of bleached and unbleached pulps were evaluated. The results showed that during the chemical pulping process, treated alfa cooked more easily than the original alfa. The treated alfa pulp also showed very good bleaching, reaching a brightness level of 94.8% ISO with a yield of 93.6% at an α-cellulose content 96.8(% with a DEDP bleaching sequence, compared to 83.2% ISO brightness level, 92.8% yield, and 95.1% α-cellulose content for bleached pulp with a DEPD bleaching sequence. Therefore, this alfa material could be considered as a worthwhile choice for cellulosic fiber supply.

  15. Pulp and paper production from Spruce wood with kraft and ...

    African Journals Online (AJOL)

    STORAGESEVER

    2010-03-15

    Mar 15, 2010 ... optical properties of resultant paper were included to determine the properties of these pulp samples. ... pulping compounds in the kraft method are Na2S and .... Scanning electron microscope (SEM) measurement of pulp.

  16. Dental pulp stone formation during orthodontic treatment: A ...

    African Journals Online (AJOL)

    2015-06-21

    Jun 21, 2015 ... the presence of dental pulp stone, gender, age, tooth type and arches. Results: Dental pulp ... primary and permanent dentition.[1] Dental pulp stones .... interpretation provided training to familiarize the other observer with the ...

  17. Catalase activity in healthy and inflamed pulp tissues of permanent ...

    African Journals Online (AJOL)

    2015-11-02

    Nov 2, 2015 ... pulps, which is due to pulpitis in comparison to healthy dental pulp. Key words: .... human dental pulp cells by Porphyromonas endodontalis lipopolysaccharide. J Endod ... Biology of disease: Free radicals and tissue injury.

  18. In vitro penetration of bleaching agents into the pulp chamber

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Valera, M C; Mancini, M N G

    2004-01-01

    To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures.......To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures....

  19. PULP DEMAND IN THE INTERNATIONAL MARKET

    Directory of Open Access Journals (Sweden)

    Edmilson Santos Cruz

    2003-01-01

    Full Text Available This study aimed at analyzing the international pulp market, taking into account themain exporting countries and importing regions, with the objective of estimating, for each market, theown-price and cross-price elasticity in relation to the demand of the pulp, differentiated for country oforigin. The model considers that imports are differentiated by origin; therefore they are not perfect substitutes. The demand from Europe, North America and the Rest of the World for the pulp from theUnited States,Canada, Sweden, Finland, Portugal and Brazil was inelastic. The Asian demand for thissome pulp was elastic. Europe and the Rest of the World showed negative cross-price elasticity, i. e.,and the imported pulp from other countries are complementary products. North America and Asiashowed positive crow-price elasticity, i. e., they consider the pulp produced in other countries assubstitute products. The net effect of the variation on the price of pulp in a country h, over the amountof pulp that goes to the region i depends on the matching of values related to the elasticity ofsubstitution and the price elasticity of the total demand.

  20. Characterization of sugar beet pulp derived oligosaccharides

    NARCIS (Netherlands)

    Leijdekkers, M.

    2015-01-01

    Abstract

    This thesis aimed at characterizing complex mixtures of sugar beet pulp derived oligosaccharides, in order to be able to monitor and optimize the enzymatic saccharification of sugar beet pulp.

    Hydrophilic interaction chromatography with on-line evaporative

  1. Pulp quality from small-diameter trees.

    Science.gov (United States)

    G.C. Myers; S. Kumar; R.R. Gustafson; R.J. Barbour; S.M. Abubakr

    1997-01-01

    Kraft and thermomechanical (TMP) pulps were prepared and evaluated from lodgepole pine and mixed Douglas-fir/western larch sawmill residue chips; lodgepole pine, Douglas-fir, and western larch submerchantable logs; and lodgepole pine, Douglas-fir, and western larch small trees and tops. Kraft pulp from small trees and tops was identical to that from submerchantable...

  2. Enzymes improve ECF bleaching of pulp

    Directory of Open Access Journals (Sweden)

    Lachenal, D.

    2006-07-01

    Full Text Available The delignification efficiency of different laccase enzymes was examined on the eucalyptus Kraft pulp. The laccase enzyme from Trametes versicolor showing the highest delignification efficiency was selected and used in the elemental chlorine-free bleaching sequence for improving the pulp bleachability. An appreciable reduction in chlorine dioxide consumption was also obtained. Further reduction in chlorine dioxide consumption was obtained when the same laccase treated pulp was subjected to an acid treatment after the extraction stage followed by the DEPD sequence. Elemental-chlorine free bleaching was also performed using the xylanase-laccase treated pulp. Xylanase treatment was incorporated to the laccase mediator system in the elemental-chlorine free bleaching both sequentially and simultaneously. The bleaching sequence DEPD followed and in both the cases, the reduction in chlorine dioxide consumption was greater in comparison to the control. The chlorine dioxide consumption was reduced further when xylanase-laccase treated pulp was given an additional acid treatment. The final pulp properties of the treated pulps were comparable to the control pulp.

  3. Activity-guided identification of acetogenins as novel lipophilic antioxidants present in avocado pulp (Persea americana).

    Science.gov (United States)

    Rodríguez-Sánchez, Dariana; Silva-Platas, Christian; Rojo, Rocío P; García, Noemí; Cisneros-Zevallos, Luis; García-Rivas, Gerardo; Hernández-Brenes, Carmen

    2013-12-30

    Avocado fruit is a rich source of health-related lipophilic phytochemicals such as monounsaturated fatty acids, tocopherols, carotenes, acetogenins and sterols. However, limited information is available on the contribution of specific phytochemicals to the overall antioxidant capacity (AOC) of the fruit. Centrifugal partition chromatography was used as fractionation tool, guided by an in vitro chemical assay of oxygen radical absorbance capacity (ORAC). Subsequent experiments focused on isolation and characterization of the chemical nature of the main contributors to lipophilic AOC of avocado pulp. ORAC values obtained for acetogenins were contrasted with results from an isolated kidney mitochondria membrane lipid peroxidation bioassay. The present study established that lipophilic AOC of the pulp was significantly higher than its hydrophilic AOC. Our results confirmed the presence of acetogenins in the fractions with highest lipophilic AOC, and for the first time linked them as contributors to lipophilic-ORAC values. Further HPLC-PDA/MS-TOF analysis led to structural elucidation of two novel acetogenins, not previously reported as present in avocado pulp, along with five already known related-compounds. Antioxidant properties observed for avocado pulp acetogenins by the ORAC assay suggested that, in the presence of an emulsifying agent, acetogenins could serve as novel lipophilic antioxidants in a food matrix. Results from isolated mitochondria lipid peroxidation bioassay, indicated that L-ORAC values which may have relevance for food matrix applications, should not be interpreted to have a direct relevance in health-related claims, compounds need to be evaluated considering the complexity of biological systems. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. Regenerative medicine using dental pulp stem cells for liver diseases.

    Science.gov (United States)

    Ohkoshi, Shogo; Hara, Hajime; Hirono, Haruka; Watanabe, Kazuhiko; Hasegawa, Katsuhiko

    2017-02-06

    Acute liver failure is a refractory disease and its prognosis, if not treated using liver transplantation, is extremely poor. It is a good candidate for regenerative medicine, where stem cell-based therapies play a central role. Mesenchymal stem cells (MSCs) are known to differentiate into multiple cell lineages including hepatocytes. Autologous cell transplant without any foreign gene induction is feasible using MSCs, thereby avoiding possible risks of tumorigenesis and immune rejection. Dental pulp also contains an MSC population that differentiates into hepatocytes. A point worthy of special mention is that dental pulp can be obtained from deciduous teeth during childhood and can be subsequently harvested when necessary after deposition in a tooth bank. MSCs have not only a regenerative capacity but also act in an anti-inflammatory manner via paracrine mechanisms. Promising efficacies and difficulties with the use of MSC derived from teeth are summarized in this review.

  5. Enhanced cellulase hydrolysis of eucalyptus waste fibers from pulp mill by Tween80-assisted ferric chloride pretreatment.

    Science.gov (United States)

    Chen, Liheng; Fu, Shiyu

    2013-04-03

    Pretreatment combining FeCl3 and Tween80 was performed for cellulose-to-ethanol conversion of eucalyptus alkaline peroxide mechanical pulping waste fibers (EAWFs). The FeCl3 pretreatment alone showed a good effect on the enzymatic hydrolysis of EAWFs, but inhibited enzyme activity to some extent. A surfactant, Tween80, added during FeCl3 pretreatment was shown to significantly enhance enzyme reaction by eluting enzymatic inhibitors such as iron(III) that are present at the surface of the pretreated biomass. Treatment temperature, liquid-solid ratio, treatment time, FeCl3 concentration, and Tween80 dosage for pretreatment were optimized as follows: 180 °C, 8:1, 30 min, 0.15 mol/L, and 1% (w/v). Pretreated EAWFs under such optimal conditions provided enzymatic glucose (based on 100 g of oven-dried feedstock) and substrate enzymatic digestibility of EAWFs of 34.8 g and 91.3% after 72 h of enzymatic hydrolysis, respectively, with an initial cellulase loading of 20 FPU/g substrate.

  6. Pulping Variables, Storage Time and Pitch Deposit | Ogunwusi ...

    African Journals Online (AJOL)

    Pulp resin is also influenced by effective alkali concentration of the pulping medium. With increase in effective alkali concentration from 13% to 15%, pulp pitch is reduced. The interaction effect of storage and effective alkali concentration was not significant indicating that reduction in pulp pitch caused by effective alkali ...

  7. Regenerative medicine in dental and oral tissues: Dental pulp mesenchymal stem cell

    Directory of Open Access Journals (Sweden)

    Janti Sudiono

    2017-08-01

    Full Text Available Background. Regenerative medicine is a new therapeutic modality using cell, stem cell and tissue engineering technologies. Purpose. To describe the regenerative capacity of dental pulp mesenchymal stem cell. Review. In dentistry, stem cell and tissue engineering technologies develop incredibly and attract great interest, due to the capacity to facilitate innovation in dental material and regeneration of dental and oral tissues. Mesenchymal stem cells derived from dental pulp, periodontal ligament and dental follicle, can be isolated, cultured and differentiated into various cells, so that can be useful for regeneration of dental, nerves, periodontal and bone tissues. Tissue engineering is a technology in reconstructive biology, which utilizes mechanical, cellular, or biological mediators to facilitate regeneration or reconstruction of a particular tissue. The multipotency, high proliferation rates and accessibility, make dental pulp as an attractive source of mesenchymal stem cells for tissue regeneration. Revitalized dental pulp and continued root development is the focus of regenerative endodontic while biological techniques that can restore lost alveolar bone, periodontal ligament, and root cementum is the focus of regenerative periodontic. Conclucion. Dentin-derived morphogens such as BMP are known to be involved in the regulation of odontogenesis. The multipotency and angiogenic capacity of DPSCs as the regenerative capacity of human dentin / pulp complex indicated that dental pulp may contain progenitors that are responsible for dentin repair. The human periodontal ligament is a viable alternative source for possible primitive precursors to be used in stem cell therapy.

  8. Effect of depth beating on the fiber properties and enzymatic saccharification efficiency of softwood kraft pulp.

    Science.gov (United States)

    Gao, Wenhua; Xiang, Zhouyang; Chen, Kefu; Yang, Rendang; Yang, Fei

    2015-01-01

    Commercial bleached softwood kraft pulp was mechanically fibrillated by a PFI-mill with beating revolution from 5000 to 30,000 r. The extent of fibrillating on the pulp was evaluated by beating degree, fiber morphological properties (fiber length, width, coarseness and curls index), water retention value (WRV) and physical properties of paper made from the pulp. Depth beating process significantly affected the pulp fibrillations as showed by the decreased fiber length and width as well as the SEM analysis, but the effects were limited after beating revolution of 15,000. Depth beating process also improved the total internal pore and inter-fibril surface areas as shown by the increased WRV values. Substrate enzymatic digestibility (SED) of beaten pulp at 5000 revolutions could reach 95% at cellulase loading of 15 FPU/g of glucan. After the enzymatic hydrolysis, the size of the pulp residues was reduced to micro-scale, and a relative uniform size distribution of the residues appeared at 10,000 r beating revolution. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. The Relix process for the resin-in-pulp recovery of uranium

    International Nuclear Information System (INIS)

    Cloete, F.L.D.

    1981-01-01

    The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performance was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp [af

  10. The dynamics of TGF-β in dental pulp, odontoblasts and dentin.

    Science.gov (United States)

    Niwa, Takahiko; Yamakoshi, Yasuo; Yamazaki, Hajime; Karakida, Takeo; Chiba, Risako; Hu, Jan C-C; Nagano, Takatoshi; Yamamoto, Ryuji; Simmer, James P; Margolis, Henry C; Gomi, Kazuhiro

    2018-03-13

    Transforming growth factor-beta (TGF-β) is critical for cell proliferation and differentiation in dental pulp. Here, we show the dynamic mechanisms of TGF-β in porcine dental pulp, odontoblasts and dentin. The mRNA of latent TGF-β1 and TGF-β3 is predominantly expressed in odontoblasts, whereas the mRNA expression level of latent TGF-β2 is high in dental pulp. TGF-β1 is a major isoform of TGF-β, and latent TGF-β1, synthesized in dental pulp, is primarily activated by matrix metalloproteinase 11 (MMP11). Activated TGF-β1 enhances the mRNA expression levels of MMP20 and full-length dentin sialophosphoprotein (DSPP) in dental pulp cells, coinciding with the induction of odontoblast differentiation. Latent TGF-β1 synthesized in odontoblasts is primarily activated by MMP2 and MMP20 in both odontoblasts and dentin. The activity level of TGF-β1 was reduced in the dentin of MMP20 null mice, although the amount of latent TGF-β1 expression did not change between wild-type and MMP20 null mice. TGF-β1 activity was reduced with the degradation of DSPP-derived proteins that occurs with ageing. We propose that to exert its multiple biological functions, TGF-β1 is involved in a complicated dynamic interaction with matrix metalloproteinases (MMPs) and/or DSPP-derived proteins present in dental pulp, odontoblasts and dentin.

  11. Pulp mill as an energy producer

    International Nuclear Information System (INIS)

    Kaulamo, O.

    1998-01-01

    The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

  12. Recruitment of dental pulp cells by dentine and pulp extracellular matrix components.

    Science.gov (United States)

    Smith, J G; Smith, A J; Shelton, R M; Cooper, P R

    2012-11-01

    The present study aimed to determine whether dentine tissue and preparations of extracellular matrix (ECM) from pulp (pECM) and dentine (dECM), and breakdown products, influenced pulp cell migration. Chemotaxis transwell and agarose spot assays demonstrated that both dentine and pulp ECM molecules acted as chemoattractants for primary pulp cells. Chemoattractant activities of dECM and pECM were enhanced when subjected to acid and enzymatic breakdown, respectively. This enhanced activity following physiologically relevant breakdown may be pertinent to the disease environment. Pulp cell migration in response to dental ECMs was dependent on an active rho pathway. Recruited cells exhibited increased stem cell marker expression indicating that dental ECMs and their breakdown products selectively attract progenitor cells that contribute to repair processes. In conclusion, combined these results indicate that ECM molecules contribute to cell recruitment necessary for regeneration of the dentine-pulp complex after injury. Copyright © 2012 Elsevier Inc. All rights reserved.

  13. Vital Pulp Therapy—Current Progress of Dental Pulp Regeneration and Revascularization

    Directory of Open Access Journals (Sweden)

    Weibo Zhang

    2010-01-01

    Full Text Available Pulp vitality is extremely important for the tooth viability, since it provides nutrition and acts as biosensor to detect pathogenic stimuli. In the dental clinic, most dental pulp infections are irreversible due to its anatomical position and organization. It is difficult for the body to eliminate the infection, which subsequently persists and worsens. The widely used strategy currently in the clinic is to partly or fully remove the contaminated pulp tissue, and fill and seal the void space with synthetic material. Over time, the pulpless tooth, now lacking proper blood supply and nervous system, becomes more vulnerable to injury. Recently, potential for successful pulp regeneration and revascularization therapies is increasing due to accumulated knowledge of stem cells, especially dental pulp stem cells. This paper will review current progress and feasible strategies for dental pulp regeneration and revascularization.

  14. Optimization of pulping conditions of abaca. An alternative raw material for producing cellulose pulp.

    Science.gov (United States)

    Jiménez, L; Ramos, E; Rodríguez, A; De la Torre, M J; Ferrer, J L

    2005-06-01

    The influence of temperature (150-170 degrees C), pulping time (15-45 min) and soda concentration (5-10%) in the pulping of abaca on the yield, kappa, viscosity, breaking length, stretch and tear index of pulp and paper sheets, was studied. Using a factorial design to identify the optimum operating conditions, equations relating the dependent variables to the operational variables of the pulping process were derived that reproduced the former with errors lower than 25%. Using a high temperature, and a medium time and soda concentration, led to pulp that was difficult to bleach (kappa 28.34) but provided acceptable strength-related properties (breaking length 4728 m; stretch 4.76%; tear index 18.25 mN m2/g), with good yield (77.33%) and potential savings on capital equipment costs. Obtaining pulp amenable to bleaching would entail using more drastic conditions than those employed in this work.

  15. The relationship between pulp calcifications and salivary gland calcifications

    OpenAIRE

    Kaswan, Sumita; Patil, Santosh; Maheshwari, Sneha; Rahman, Farzan; Khandelwal, Suneet

    2014-01-01

    Aim: Pulp stones are discrete calcified bodies found in the dental pulp. Sialolithasis is the most common salivary gland disease. The aim of the present study was to determine the relationship between the pulp stones and salivary gland stones. Material and Methods: 196 patients were randomly selected from the out patient department for the study. The periapical radiographs for all patients were evaluated for the presence or absence of the narrowing of dental pulp chambers and pulp canals. The...

  16. Low Temperature Soda-Oxygen Pulping of Bagasse

    OpenAIRE

    Fengxia Yue; Ke-Li Chen; Fachuang Lu

    2016-01-01

    Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum coo...

  17. Lipid Peroxidation: Pathophysiology and Pharmacological Implications in the Eye

    Directory of Open Access Journals (Sweden)

    Ya Fatou eNjie-Mbye

    2013-12-01

    Full Text Available Oxygen-derived free radicals such as hydroxyl and hydroperoxyl species have been shown to oxidize phospholipids and other membrane lipid components leading to lipid peroxidation. In the eye, lipid peroxidation has been reported to play an important role in degenerative ocular diseases (age-related macular degeneration, cataract, glaucoma, diabetic retinopathy. Indeed, ocular tissues are prone to damage from reactive oxygen species due to stress from constant exposure of the eye to sunlight, atmospheric oxygen and environmental chemicals. Furthermore, free radical catalyzed peroxidation of long chain polyunsaturated acids (LCPUFAs such as arachidonic acid and docosahexaenoic acid leads to generation of LCPUFA metabolites including isoprostanes and neuroprostanes that may further exert pharmacological/toxicological actions in ocular tissues. Evidence from literature supports the presence of endogenous defense mechanisms against reactive oxygen species in the eye, thereby presenting new avenues for the prevention and treatment of ocular degeneration. Hydrogen peroxide (H2O2 and synthetic peroxides can exert pharmacological and toxicological effects on tissues of the anterior uvea of several mammalian species. There is evidence suggesting that the retina, especially retinal ganglion cells can exhibit unique characteristics of antioxidant defense mechanisms. In the posterior segment of the eye, H2O2 and synthetic peroxides produce an inhibitory action on glutamate release (using [3H]-D-aspartate as a marker, in vitro and on the endogenous glutamate and glycine concentrations in vivo. In addition to peroxides, isoprostanes can elicit both excitatory and inhibitory effects on norepinephrine (NE release from sympathetic nerves in isolated mammalian iris ciliary bodies. Whereas isoprostanes attenuate dopamine release from mammalian neural retina, in vitro, these novel arachidonic acid metabolites exhibit a biphasic regulatory effect on glutamate release

  18. Electrothermal debracketing: patient acceptance and effects on the dental pulp.

    Science.gov (United States)

    Dovgan, J S; Walton, R E; Bishara, S E

    1995-09-01

    Adhesives bond ceramic brackets so effectively that their removal by mechanical forces can fracture the brackets and may damage the tooth surface. Electrothermal debracketers have been developed to facilitate removal; whether the heat generated will damage the underlying pulp is unclear. In our experiment, a prototype device with a high heat tip was used to remove brackets from premolars in patients. The following parameters were evaluated: (1) time required for removal, (2) patient acceptance, and (3) histologic effect on the pulp. Forty-eight experimental teeth planned for orthodontic extraction were bonded by a filled Bis-GMA composite resin and a monocrystalline sapphire bracket. After the chemically cured composite set, debracketing was performed according to the manufacturer's recommendations. Seventeen premolars were not etched or bracketed and served as controls. The interval between heat application and removal of the bracket was timed. Patients were questioned as to sensations during debracketing. Teeth were extracted at 5 to 7 or 28 to 32 days and histologically prepared. Pulps were evaluated for alterations. Brackets were removed in an average of 2.1 seconds, usually at the bracket/composite interface. Patient acceptance was generally positive. Pulpal necrosis was not observed but, in a number of specimens, slight inflammation and odontoblastic disruption occurred at both observation periods.

  19. Wood-plastic composites using thermomechanical pulp made from oxalic acid-pretreated red pine chips

    Science.gov (United States)

    J.E. Winandy; N.M. Stark; E. Horn

    2008-01-01

    The characteristics and properties of wood fiber is one of many factors of critical importance to the performance of wood-plastic composites. In commercial thermo-mechanical pulping (TMP) of wood chips to produce fibers, high temperatures (>100°C) are used to separate the fibers during TMP refining. These mechanical pressures and temperatures are usually modulated...

  20. 21 CFR 872.1720 - Pulp tester.

    Science.gov (United States)

    2010-04-01

    ... battery powered device intended to evaluate the pulpal vitality of teeth by employing high frequency current transmitted by an electrode to stimulate the nerve tissue in the dental pulp. (b) Classification...

  1. Pulpectomy in hyperemic pulp and accelerated root resorption in primary teeth: A review with associated case report

    Directory of Open Access Journals (Sweden)

    Tarun Walia

    2014-01-01

    Full Text Available Persistent hemorrhage after complete amputation of coronal pulp is a common clinical finding during pulpotomy procedure in primary teeth. These teeth are best managed with pulpectomy, but they have hyperemic pulp with some remaining vital tissue. Good chemico-biomechanical preparation of primary canals cannot guarantee complete removal of this vital tissue from inaccessible areas. Use of Ca(OH 2 containing root filling pastes in vital pulp tissue can cause accelerated resorption of primary roots. The possible mechanism behind such extensive root resorption is discussed with review of literature. A case report of a child with 30 months follow-up is presented and discussed.

  2. Aging of in vitro pulp illustrates change of inflammation and dentinogenesis.

    Science.gov (United States)

    Lee, Young-Hee; Kim, Go-Eun; Cho, Hye-Jin; Yu, Mi-Kyoung; Bhattarai, Govinda; Lee, Nan-Hee; Yi, Ho-Keun

    2013-03-01

    Dental pulp functions include pulp cell activity involvement in dentin formation. In this study we investigated the age-related changes in dental pulp cells that may influence pulp cell activity for restoring pulp function. Human dental pulp cells (HDPCs) were serially subcultured until spontaneously arrested. Altered expression of chronic inflammatory molecules and age-related molecules were determined by Western blotting. Odontogenic functions impaired by senescence were assayed by Western blotting, reverse transcriptase polymerase chain reaction, alkaline phosphatase activity, and alizarin red S staining. To understand the mechanism of aging process by stress-induced premature senescence (SIPS), the cells were treated with H(2)O(2). Replicative senescence and SIPS were also compared. Replicative senescence of HDPCs was characterized by senescence-associated β-galactosidase activity and reactive oxygen species formation. These cells exhibited altered expression of chronic inflammatory molecules such as intracellular adhesion molecule-1, vascular cell adhesion molecule-1, peroxisome proliferator activated receptor-gamma, and heme oxygenase-1 and age-related molecules such as p53, p21, phosphorylated-extracellular signal-regulated kinase, and c-myb. SIPS cell results were similar to replicative senescence. Furthermore, HDPCs decreased odontogenic markers such as dentin sialophosphoprotein and dentin matrix-1 and osteogenic markers such as bone morphogenetic protein-2 and -7, runt-related transcription factor-2, osteopontin, alkaline phosphatase activity, and mineralized nodule formation by replicative senescence and SIPS. This study suggests that development of aging-related molecules in pulp cells offers understanding of cellular mechanisms and biological events responsible for tooth preservation and maintenance strategies for healthy teeth across the life span. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  3. Uranium precipitation with hydrogen peroxide

    International Nuclear Information System (INIS)

    Brown, R.A.

    1980-01-01

    Although hydrogen peroxide precipitation of uranium continues to be used primarily as means of producing a high purity yellowcake, it has also become an important process due to its superior physical properties. Processing costs such as filtering, drying and/or calcining and drumming, can be reduced. 5 refs

  4. Hydrogen peroxide: importance and determination

    OpenAIRE

    Mattos, Ivanildo Luiz de; Shiraishi, Karina Antonelli; Braz, Alexandre Delphini; Fernandes, João Roberto

    2003-01-01

    A brief discussion about the hydrogen peroxide importance and its determination is presented. It was emphasized some consideration of the H2O2 as reagent (separated or combined), uses and methods of analysis (techniques, detection limits, linear response intervals, sensor specifications). Moreover, it was presented several applications, such as in environmental, pharmaceutical, medicine and food samples.

  5. Influence of alkaline hydrogen peroxide pre-hydrolysis on the isolation of microcrystalline cellulose from oil palm fronds.

    Science.gov (United States)

    Owolabi, Abdulwahab F; Haafiz, M K Mohamad; Hossain, Md Sohrab; Hussin, M Hazwan; Fazita, M R Nurul

    2017-02-01

    In the present study, microcrystalline cellulose (MCC) was isolated from oil palm fronds (OPF) using chemo-mechanical process. Wherein, alkaline hydrogen peroxide (AHP) was utilized to extract OPF fibre at different AHP concentrations. The OPF pulp fibre was then bleached with acidified sodium chlorite solution followed by the acid hydrolysis using hydrochloric acid. Several analytical methods were conducted to determine the influence of AHP concentration on thermal properties, morphological properties, microscopic and crystalline behaviour of isolated MCC. Results showed that the MCC extracted from OPF fibres had fibre diameters of 7.55-9.11nm. X-ray diffraction (XRD) analyses revealed that the obtained microcrystalline fibre had both celluloses I and cellulose II polymorphs structure, depending on the AHP concentrations. The Fourier transmission infrared (FTIR) analyses showed that the AHP pre-hydrolysis was successfully removed hemicelluloses and lignin from the OPF fibre. The crystallinity of the MCC was increased with the AHP concentrations. The degradation temperature of MCC was about 300°C. The finding of the present study showed that pre-treatment process potentially influenced the quality of the isolation of MCC from oil palm fronds. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Low Temperature Soda-Oxygen Pulping of Bagasse.

    Science.gov (United States)

    Yue, Fengxia; Chen, Ke-Li; Lu, Fachuang

    2016-01-13

    Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today's pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm³/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115-125 °C), this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

  7. Low Temperature Soda-Oxygen Pulping of Bagasse

    Directory of Open Access Journals (Sweden)

    Fengxia Yue

    2016-01-01

    Full Text Available Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm3/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115–125 °C, this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

  8. Color, TOC and AOX removals from pulp mill effluent by advanced oxidation processes: A comparative study

    International Nuclear Information System (INIS)

    Catalkaya, Ebru Cokay; Kargi, Fikret

    2007-01-01

    Pulp mill effluent containing toxic chemicals was treated by different advanced oxidation processes (AOPs) consisting of treatments by hydrogen peroxide, Fenton's reagent (H 2 O 2 /Fe 2+ ), UV, UV/H 2 O 2 , photo-Fenton (UV/H 2 O 2 /Fe 2+ ), ozonation and peroxone (ozone/H 2 O 2 ) in laboratory-scale reactors for color, total organic carbon (TOC) and adsorbable organic halogens (AOX) removals from the pulp mill effluent. Effects of some operating parameters such as the initial pH, oxidant and catalyst concentrations on TOC, color, AOX removals were investigated. Almost every method used resulted in some degree of color removal from the pulp mill effluent. However, the Fenton's reagent utilizing H 2 O 2 /Fe 2+ resulted in the highest color, TOC and AOX removals under acidic conditions when compared with the other AOPs tested. Approximately, 88% TOC, 85% color and 89% AOX removals were obtained by the Fenton's reagent at pH 5 within 30 min. Photo-Fenton process yielded comparable TOC (85%), color (82%) and AOX (93%) removals within 5 min due to oxidations by UV light in addition to the Fenton's reagent. Fast oxidation reactions by the photo-Fenton treatment makes this approach more favorable as compared to the others used

  9. Kinetics of pulp mill effluent treatment by ozone-based processes

    International Nuclear Information System (INIS)

    Ko, Chun-Han; Hsieh, Po-Hung; Chang, Meng-Wen; Chern, Jia-Ming; Chiang, Shih-Min; Tzeng, Chewn-Jeng

    2009-01-01

    The wastewaters generated from wood pulping and paper production processes are traditionally treated by biological and physicochemical processes. In order to reduce chemical oxygen demand (COD) and color to meet increasingly strict discharge standards, advanced oxidation processes (AOPs) are being adapted as polishing treatment units. Various ozone-based processes were used in this study to treat simulated wastewaters prepared from black liquor from a hardwood Kraft pulp mill in Taiwan. The experimental results showed that the COD and color were primarily removed by direct ozone oxidation and activated carbon adsorption. While the addition of activated carbon could enhance the COD and color removal during ozonation, the addition of hydrogen peroxide improved the color removal only. For the various ozone-based treatment processes, kinetic models were developed to satisfactorily predict the COD and color removal rates. According to the kinetic parameters obtained from the various ozone-based processes, the enhanced COD and color removal of ozonation in the presence of activated carbon was attributed to the regeneration of the activated carbon by ozonation. These kinetic models can be used for reactor design and process design to treat pulping wastewater using ozone-based processes.

  10. The effect of irradiation in the quality of the avocado frozen pulp

    International Nuclear Information System (INIS)

    Valdivia, M.A.; Bustos, Ma. Emilia; Ruiz, Javier; Ruiz, Luisa F.

    2002-01-01

    The quality of frozen avocado pulp irradiated with 60 Co gamma rays at doses of: 0.5, 1.0, 1.5, and 2.5 kGy, was studied. These are possible doses for reducing the content of bacteria Listeria monocytogenes by 1-4 log cycles. The study principally consisted of weekly evaluations of damages caused in lipids and chlorophyll pigment over a period of one year. No significant differences were found in either hydrolysis rancidity or in the oxidative rancidity for any of the doses. The concentrations of fatty acids and peroxides were below those established by Codex Alimentarius. This means that the quality of the oil in the frozen avocado pulp remains acceptable. The kinetic model for the oxidative rancidity is of first order and the shelf life of the product is of about 120 weeks. The concentrations of the fatty acids and of malondialdehyde were not high enough to produce off-flavors. It was also determined that the radiation doses did not influence the chemistry of the chlorophyll. The results were confirmed by the panelists, who accepted irradiated frozen pulp at the highest radiation dose

  11. The effect of irradiation in the quality of the avocado frozen pulp

    Energy Technology Data Exchange (ETDEWEB)

    Valdivia, M.A. E-mail: mavald@servidor.unam.mx; Bustos, Ma. Emilia; Ruiz, Javier; Ruiz, Luisa F

    2002-03-01

    The quality of frozen avocado pulp irradiated with {sup 60}Co gamma rays at doses of: 0.5, 1.0, 1.5, and 2.5 kGy, was studied. These are possible doses for reducing the content of bacteria Listeria monocytogenes by 1-4 log cycles. The study principally consisted of weekly evaluations of damages caused in lipids and chlorophyll pigment over a period of one year. No significant differences were found in either hydrolysis rancidity or in the oxidative rancidity for any of the doses. The concentrations of fatty acids and peroxides were below those established by Codex Alimentarius. This means that the quality of the oil in the frozen avocado pulp remains acceptable. The kinetic model for the oxidative rancidity is of first order and the shelf life of the product is of about 120 weeks. The concentrations of the fatty acids and of malondialdehyde were not high enough to produce off-flavors. It was also determined that the radiation doses did not influence the chemistry of the chlorophyll. The results were confirmed by the panelists, who accepted irradiated frozen pulp at the highest radiation dose.

  12. The effect of irradiation in the quality of the avocado frozen pulp

    Science.gov (United States)

    Valdivia, Ma. Ángeles; Bustos, Ma. Emilia; Ruiz, Javier; Ruiz, Luisa F.

    2002-03-01

    The quality of frozen avocado pulp irradiated with 60Co gamma rays at doses of: 0.5, 1.0, 1.5, and 2.5 kGy, was studied. These are possible doses for reducing the content of bacteria Listeria monocytogenes by 1-4 log cycles. The study principally consisted of weekly evaluations of damages caused in lipids and chlorophyll pigment over a period of one year. No significant differences were found in either hydrolysis rancidity or in the oxidative rancidity for any of the doses. The concentrations of fatty acids and peroxides were below those established by Codex Alimentarius. This means that the quality of the oil in the frozen avocado pulp remains acceptable. The kinetic model for the oxidative rancidity is of first order and the shelf life of the product is of about 120 weeks. The concentrations of the fatty acids and of malondialdehyde were not high enough to produce off-flavors. It was also determined that the radiation doses did not influence the chemistry of the chlorophyll. The results were confirmed by the panelists, who accepted irradiated frozen pulp at the highest radiation dose.

  13. Inhibition of odontogenic differentiation of human dental pulp cells by dental resin monomers.

    Science.gov (United States)

    Kwon, Ji Hyun; Park, Hee Chul; Zhu, Tingting; Yang, Hyeong-Cheol

    2015-01-01

    Dental resin monomers that are leached from the resin matrix due to incomplete polymerization can affect the viability and various functions of oral tissues and cells. In this study, the effects of triethylene glycol dimethacrylate (TEGDMA) and 2-hydroxyethyl methacrylate (HEMA) on odontogenic differentiation of human dental pulp cells (HDPCs) were examined. To mimic clinical situations, dental pulp cells were treated with resin monomers for 24 h prior to the analysis of alkaline phosphatase (ALP) activity and mRNA expression of genes related to pulp cell differentiation. To elucidate the underlying signaling pathways, regulation of mitogen-activated protein (MAP) kinases by resin monomers was also investigated. The ALP activity of HDPCs was reduced by TEGDMA and HEMA at noncytotoxic concentrations. The mRNA expression of dentin sialophosphoprotein (DSPP), osteocalcin (OCN), and osteopontin (OPN) was also downregulated by resin monomers. However, DSPP expression was not affected by hydrogen peroxide (H2O2). Among the MAP kinases examined, ERK activation (ERK phosphorylation) was not affected by either resin monomers or H2O2, whereas JNK was phosphorylated by TEGDMA and HEMA. Phospho-p38 was upregulated by HEMA, while TEGDMA and H2O2 suppressed p38 phosphorylation. Exposure to TEGDMA and HEMA for a limited period suppresses differentiation of HDPCs via different signaling pathways.

  14. Expression and Function of Hypoxia Inducible Factor-1α and Vascular Endothelial Growth Factor in Pulp Tissue of Teeth under Orthodontic Movement

    Directory of Open Access Journals (Sweden)

    Fulan Wei

    2015-01-01

    Full Text Available Orthodontic force may lead to cell damage, circulatory disturbances, and vascular changes of the dental pulp, which make a hypoxic environment in pulp. In order to maintain the homeostasis of dental pulp, hypoxia will inevitably induce the defensive reaction. However, this is a complex process and is regulated by numerous factors. In this study, we established an experimental animal model of orthodontic tooth movement to investigate the effects of mechanical force on the expression of VEGF and HIF-1α in dental pulp. Histological analysis of dental pulp and expressions of HIF-1α and VEGF proteins in dental pulp were examined. The results showed that inflammation and vascular changes happened in dental pulp tissue in different periods. Additionally, there were significant changes in the expression of HIF-1α and VEGF proteins under orthodontic force. After application of mechanical load, expression of HIF-1α and VEGF was markedly positive in 1, 3, 7 d, and 2 w groups, and then it weakened in 4 w group. These findings suggested that the expression of HIF-1α and VEGF was enhanced by mechanical force. HIF-1α and VEGF may play an important role in retaining the homeostasis of dental pulp during orthodontic tooth movement.

  15. Hydrothermal carbonization of autoclaved municipal solid waste pulp and anaerobically treated pulp digestate

    Science.gov (United States)

    In this study, the autoclaved organic fraction of municipal solid waste pulp (OFMSW) and the digestate from OFMSW pulp after anaerobic digestion (AD) were processed by hydrothermal carbonization (HTC) at 200, 250, and 300 °C for 30 min and 2 h. The focus of this work was to evaluate the potential fo...

  16. Extracellular matrix of dental pulp stem cells: Applications in pulp tissue engineering using somatic MSCs

    Directory of Open Access Journals (Sweden)

    Sriram eRavindran

    2014-01-01

    Full Text Available Dental Caries affects approximately 90% of the world’s population. At present, the clinical treatment for dental caries is root canal therapy. This treatment results in loss of tooth sensitivity and vitality. Tissue engineering can potentially solve this problem by enabling regeneration of a functional pulp tissue. Dental pulp stem cells (DPSCs have been shown to be an excellent source for pulp regeneration. However, limited availability of these cells hinders its potential for clinical translation. We have investigated the possibility of using somatic mesenchymal stem cells from other sources for dental pulp tissue regeneration using a biomimetic dental pulp extracellular matrix (ECM incorporated scaffold. Human periodontal ligament stem cells (PDLSCs and human bone marrow stromal cells (HMSCs were investigated for their ability to differentiate towards an odontogenic lineage. In vitro real-time PCR results coupled with histological and immunohistochemical examination of the explanted tissues confirmed the ability of PDLSCs and HMSCs to form a vascularized pulp-like tissue. These findings indicate that the dental pulp stem derived ECM scaffold stimulated odontogenic differentiation of PDLSCs and HMSCs without the need for exogenous addition of growth and differentiation factors. This study represents a translational perspective toward possible therapeutic application of using a combination of somatic stem cells and extracellular matrix for pulp regeneration.

  17. EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

    Directory of Open Access Journals (Sweden)

    Ahmad Azizi Mossello

    2010-06-01

    Full Text Available Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ pulp of kenaf fibers versus old corrugated container (OCC and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the highest strength properties, except for tear resistance. The OCC gave paper with the lowest strength properties. In the case of kenaf fractions, bast pulp with high freeness needed less beating than softwood and produced paper with high tear resistance. Core fiber, which had the lowest freeness and highest drainage time, led to paper with high strength but very low tear resistance. Kenaf whole stem pulp showed intermediate properties between core and bast and close to those of unbleached softwood pulp, but with very lower beating requirement. Finally, kenaf whole stem, due to its strength properties, moderate separation cost, and simple pulping process, was judged to be more suitable for commercialization for linerboard production in Malaysia.

  18. 21 CFR 529.1150 - Hydrogen peroxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Hydrogen peroxide. 529.1150 Section 529.1150 Food... DRUGS, FEEDS, AND RELATED PRODUCTS CERTAIN OTHER DOSAGE FORM NEW ANIMAL DRUGS § 529.1150 Hydrogen peroxide. (a) Specifications. Each milliliter of solution contains 396.1 milligrams (mg) hydrogen peroxide...

  19. The increasing of odontoblast-like cell number on direct pulp capping of Rattus norvegicus using chitosan

    OpenAIRE

    Prananingrum, Widyasri

    2010-01-01

    Background: Pulpal perforation care with direct pulp capping in the case of reversible pulpitis due to mechanical trauma was performed with chitosan which has the ability to facilitate migration, proliferation, and progenitor cell differentiation. Purpose: The purpose of this study was to determine the increasing number of odontoblast-like cells in direct pulp capping dental care of Rattus norvegicus using chitosan for seven and fourteen days. Methods: Samples were molars of male Rattus norve...

  20. STARCH/PULP-FIBER BASED PACKAGING FOAMS AND CAST FILMS CONTAINING ALASKAN FISH BY-PRODUCTS (WASTE)

    OpenAIRE

    Syed H. Imam; Bor-Sen Chiou; Delilah Woods; Justin Shey; Gregory M. Glenn; William J. Orts; Rajnesh Narayan; Robert J. Avena-Bustillos; Tara H. McHugh; Alberto Pantoja; Peter J. Bechtel

    2008-01-01

    Baked starch/pulp foams were prepared from formulations containing zero to 25 weight percent of processed Alaskan fish by-products that consisted mostly of salmon heads, pollock heads, and pollock frames (bones and associated remains produced in the filleting operation). Fish by-products thermoformed well along with starch and pulp fiber, and the foam product (panels) exhibited useful mechanical properties. Foams with all three fish by-products, ranging between 10 and 15 wt%, showed the highe...

  1. Electrochemical behaviour of platinum in hydrogen peroxide solution (1963)

    International Nuclear Information System (INIS)

    Prost, G.H.

    1963-06-01

    The relative stability of hydrogen peroxide in aqueous solution at 25 deg. C, allows its amperometric determination from the theory, using either its cathodic reduction or its anodic oxidation. The cathodic reduction yields a wave on a platinum electrode only when some oxygen is present in the solution. It cannot, therefore, be used for electrochemical determination. On the other hand, the anodic oxidation on platinum produces a wave which might be used. However, a passivation of platinum occurs at the same time. This passivation process is studied by means of potentio-kinetic, potentio-static, intensio-static curves and of pH measurements in the vicinity of the anode. A mechanism for passivation is presented, which takes into account the role of hydrogen peroxide as a reducing agent. This passivation rules out any analytical application of the oxidation reaction of hydrogen peroxide. (author) [fr

  2. PULP OBTAINING METHOD FOR PACKAGE PRODUCTION

    Directory of Open Access Journals (Sweden)

    V. V. Kuzmich

    2015-01-01

    Full Text Available The paper presents a new method for obtaining pulp which is used for production of cardboard, paper and package while using carbon dioxide and hydrazine hydrate and neutral-sulfite  shive cooking. Output increase of  the desired product can be explained by reduction in destruction of plant raw material carbohydrates during its cooking process. Quality improvement of the desired product (improvement in bleaching and output is attributed to the fact that usage of carbon dioxide and hydrazine contributes to provision of polysaccharide chain resistance to destruction due to the presence of  end links having structure of metasaccharinic and aldonic acids.The author has developed a new method for pulp obtaining on the basis of the executed investigations  and literature data.  СО2 and hydrazine hydrate have been used for obtaining pulp. Method invention concerns pulp obtaining and it can be used for paper and cardboard package manufacturing in pulp and paper industry.The method is to be carried in the following way: pulp-containing plant raw material is loaded into an autoclave and then aqua solution of sodium monosulfite containing hydrazine hydrate that constitutes 4–5 % of absolute dry pulp-containing raw material mass with liquid module 1:6–1:8 is supplied into the autoclave. The autoclave is closed for operation under pressure and the solution is carbonated under pressure which constitutes 5–8 % of absolute dry plant raw material (shover. Temperature is subsequently raised up to 180 °С in the space of 2 hours and cooking is carried out in the course of 4 hours. Usage of  the proposed method for shover cooking makes it possible to reduce monosulfite cooking process and improve qualitative characteristics and output of the desired product.  In addition to above mentioned fact there is a possibility to improve bleaching and final product output. 

  3. CHEMICAL COMPOSITION, CRYSTALLINITY, AND THERMAL DEGRADATION OF BLEACHED AND UNBLEACHED KENAF BAST (Hibiscus cannabinus PULP AND NANOFIBERS

    Directory of Open Access Journals (Sweden)

    Mehdi Jonoobi

    2009-05-01

    Full Text Available Kenaf (Hibiscus cannabinus nanofibers were isolated from unbleached and bleached pulp by a combination of chemical and mechanical treatments. The chemical methods were based on NaOH-AQ (anthraquinone and three-stage bleaching (DEpD processes, whereas the mechanical techniques involved refining, cryo-crushing, and high-pressure homogenization. The size and morphology of the obtained fibers were characterized by environmental scanning electron microscopy (ESEM and transmission electron microscopy (TEM, and the studies showed that the isolated nanofibers from unbleached and bleached pulp had diameters between 10-90 nm, while their length was in the micrometer range. Fourier transform infrared (FTIR spectroscopy demonstrated that the content of lignin and hemicellulose decreased in the pulping process and that lignin was almost completely removed during bleaching. Moreover, thermogravimetric analysis (TGA indicated that both pulp types as well as the nanofibers displayed a superior thermal stability as compared to the raw kenaf. Finally, X-ray analyses showed that the chemo-mechanical treatments altered the crystallinity of the pulp and the nanofibers: the bleached pulp had a higher crystallinity than its unbleached counterpart, and the bleached nanofibers presented the highest crystallinity of all the investigated materials.

  4. Preparation and Properties of Nanocellulose from Organosolv Straw Pulp

    Science.gov (United States)

    Barbash, V. A.; Yaschenko, O. V.; Shniruk, O. M.

    2017-03-01

    The object of this work is to present a study of nanocellulose preparation from organosolv straw pulp (OSP) and its properties. OSP was obtained through thermal treatment in the system of isobutyl alcohol-H2O-KOH-hydrazine followed by processing in the mixture of acetic acid and hydrogen peroxide for bleaching and removal of residual non-cellulosic components. We have obtained nanocellulose from OSP through acid hydrolysis with lower consumption of sulfuric acid and followed by ultrasound treatment. The structural change and crystallinity degree of OSP and nanocellulose were studied by means of SEM and XRD techniques. It has been established that nanocellulose has a density up to 1.3 g/cm3, transparency up to 70%, crystallinity degree 72.5%. The TEM and AFM methods shown that nanocellulose have diameter of particles in the range from 10 to 40 nm. Thermogravimetric analysis confirmed that nanocellulose films have more dense structure and smaller mass loss in the temperature range 220-260 °C compared with OSP. The obtained nanocellulose films had high Young's modulus up to 11.45 GPa and tensile strength up to 42.3 MPa. The properties of obtained nanocellulose from OSP exhibit great potential in its application for the preparation of new nanocomposite materials.

  5. Transenamel and transdentinal penetration of hydrogen peroxide applied to cracked or microabrasioned enamel.

    Science.gov (United States)

    Briso, A L F; Lima, A P B; Gonçalves, R S; Gallinari, M O; dos Santos, P H

    2014-01-01

    The present study evaluated transenamel and transdentinal penetration of hydrogen peroxide during tooth whitening recognized in altered enamel by the presence of cracks or microabrasion. We used 72 experimental units (n=20) obtained from bovine incisors: GI-sound enamel; GII-teeth showing visible enamel cracks (4 mm to 5.7 mm in length); and GIII-microabrasioned enamel. The 12 remaining specimens were used to analyze the enamel surface morphology using scanning electron microscopy. The specimens were cylindrical and 5.7 mm in diameter and 3.5 mm thick. A product based on 35% hydrogen peroxide was used for bleaching, following the manufacturer's recommendations for use. To quantify the H2O2 penetration, the specimens were placed in artificial pulp chambers containing an acetate buffer solution. After bleaching, the solution was collected and adequately proportioned with leucocrystal violet, peroxidase enzyme, and deionized water. The resulting solution was evaluated using ultraviolet visible reflectance spectrophotometer equipment. The data were analyzed by analysis of variance (ANOVA) and Fisher's PLSD at a significance level of 0.05, and significant differences in the penetration of peroxide in different substrate conditions were observed (penamel was microabraded showed intermediate values when compared to the control group. Microabrasion and the presence of cracks in the enamel make this substrate more susceptible to penetration of hydrogen peroxide during in-office whitening.

  6. Thermochemistry of cyclic acetone peroxides

    Energy Technology Data Exchange (ETDEWEB)

    Sinditskii, V.P., E-mail: vps@rctu.ru [Mendeleev University of Chemical Technology, 9 Miusskaya Square, 125047 Moscow (Russian Federation); Kolesov, V.I.; Egorshev, V.Yu.; Patrikeev, D.I. [Mendeleev University of Chemical Technology, 9 Miusskaya Square, 125047 Moscow (Russian Federation); Dorofeeva, O.V. [Department of Chemistry, Lomonosov Moscow State University, 119991 Moscow (Russian Federation)

    2014-06-01

    Highlights: • Old data on DADP and TATP enthalpies of formation have been revised. • Combining Gaussian-4 (G4) theory with an isodesmic reaction scheme allowed calculated enthalpies of formation of TATP and DADP. • Oxygen bomb calorimetry measurements allowed experimental enthalpies of formation of the peroxides. • Both experimental and calculated values show a satisfactory agreement between each other. • The newly obtained enthalpies reasonably account for the observed derivative parameters: heats of decomposition, combustion, and explosion. - Abstract: Two potentially initiating explosive peroxides, diacetonediperoxide (DADP) and triacetonetriperoxide (TATP), were studied in respect to their thermochemical properties. To get the internally self-consistent estimations of gas-phase enthalpy of formation of DADP and TATP, their values were calculated by combining Gaussian-4 (G4) theory with an isodesmic reaction scheme. The energies of combustion (Δ{sub c}U) were measured and the standard enthalpies of formation (Δ{sub f}H{sub 298}{sup °}) of DADP and TATP were derived using the standard enthalpies of formation of the combustion products. The heat of explosion was measured for small low-pressed charges of the peroxides. The obtained enthalpies of formation of DADP and TATP were found to agree well with quantum chemical calculations and reasonably account for the observed derivative parameters: heats of decomposition, combustion, and detonation.

  7. Development of a Direct Pulp-capping Model for the Evaluation of Pulpal Wound Healing and Reparative Dentin Formation in Mice.

    Science.gov (United States)

    Song, Minju; Kim, Sol; Kim, Terresa; Park, Sil; Shin, Ki-Hyuk; Kang, Mo; Park, No-Hee; Kim, Reuben

    2017-01-12

    Dental pulp is a vital organ of a tooth fully protected by enamel and dentin. When the pulp is exposed due to cariogenic or iatrogenic injuries, it is often capped with biocompatible materials in order to expedite pulpal wound healing. The ultimate goal is to regenerate reparative dentin, a physical barrier that functions as a "biological seal" and protects the underlying pulp tissue. Although this direct pulp-capping procedure has long been used in dentistry, the underlying molecular mechanism of pulpal wound healing and reparative dentin formation is still poorly understood. To induce reparative dentin, pulp capping has been performed experimentally in large animals, but less so in mice, presumably due to their small sizes and the ensuing technical difficulties. Here, we present a detailed, step-by-step method of performing a pulp-capping procedure in mice, including the preparation of a Class-I-like cavity, the placement of pulp-capping materials, and the restoration procedure using dental composite. Our pulp-capping mouse model will be instrumental in investigating the fundamental molecular mechanisms of pulpal wound healing in the context of reparative dentin in vivo by enabling the use of transgenic or knockout mice that are widely available in the research community.

  8. Hydrogen peroxide kinetics in water radiolysis

    Science.gov (United States)

    Iwamatsu, Kazuhiro; Sundin, Sara; LaVerne, Jay A.

    2018-04-01

    The kinetics of the formation and reaction of hydrogen peroxide in the long time γ- radiolysis of water is examined using a combination of experiment with model calculations. Escape yields of hydrogen peroxide on the microsecond time scale are easily measured with added radical scavengers even with substantial amounts of initial added hydrogen peroxide. The γ-radiolysis of aqueous hydrogen peroxide solutions without added radical scavengers reach a steady state limiting concentration of hydrogen peroxide with increasing dose, and that limit is directly proportional to the initial concentration of added hydrogen peroxide. The dose necessary to reach that limiting hydrogen peroxide concentration is also proportional to the initial concentration, but dose rate has a very small effect. The addition of molecular hydrogen to aqueous solutions of hydrogen peroxide leads to a decrease in the high dose limiting hydrogen peroxide concentration that is linear with the initial hydrogen concentration, but the amount of decrease is not stoichiometric. Proton irradiations of solutions with added hydrogen peroxide and hydrogen are more difficult to predict because of the decreased yields of radicals; however, with a substantial increase in dose rate there is a sufficient decrease in radical yields that hydrogen addition has little effect on hydrogen peroxide decay.

  9. Dental pulp stem cells in regenerative dentistry.

    Science.gov (United States)

    Casagrande, Luciano; Cordeiro, Mabel M; Nör, Silvia A; Nör, Jacques E

    2011-01-01

    Stem cells constitute the source of differentiated cells for the generation of tissues during development, and for regeneration of tissues that are diseased or injured postnatally. In recent years, stem cell research has grown exponentially owing to the recognition that stem cell-based therapies have the potential to improve the life of patients with conditions that span from Alzheimer's disease to cardiac ischemia to bone or tooth loss. Growing evidence demonstrates that stem cells are primarily found in niches and that certain tissues contain more stem cells than others. Among these tissues, the dental pulp is considered a rich source of mesenchymal stem cells that are suitable for tissue engineering applications. It is known that dental pulp stem cells have the potential to differentiate into several cell types, including odontoblasts, neural progenitors, osteoblasts, chondrocytes, and adipocytes. The dental pulp stem cells are highly proliferative. This characteristic facilitates ex vivo expansion and enhances the translational potential of these cells. Notably, the dental pulp is arguably the most accessible source of postnatal stem cells. Collectively, the multipotency, high proliferation rates, and accessibility make the dental pulp an attractive source of mesenchymal stem cells for tissue regeneration. This review discusses fundamental concepts of stem cell biology and tissue engineering within the context of regenerative dentistry.

  10. An Overview of Pathogen Recognition Receptors for Innate Immunity in Dental Pulp

    Directory of Open Access Journals (Sweden)

    Ji-Hyun Jang

    2015-01-01

    Full Text Available Pathogen recognition receptors (PRRs are a class of germ line-encoded receptors that recognize pathogen-associated molecular patterns (PAMPs. The activation of PRRs is crucial for the initiation of innate immunity, which plays a key role in first-line defense until more specific adaptive immunity is developed. PRRs differ in the signaling cascades and host responses activated by their engagement and in their tissue distribution. Currently identified PRR families are the Toll-like receptors (TLRs, the C-type lectin receptors (CLRs, the nucleotide-binding oligomerization domain-like receptors (NLRs, the retinoic acid-inducible gene-I-like receptors (RLRs, and the AIM2-like receptor (ALR. The environment of the dental pulp is substantially different from that of other tissues of the body. Dental pulp resides in a low compliance root canal system that limits the expansion of pulpal tissues during inflammatory processes. An understanding of the PRRs in dental pulp is important for immunomodulation and hence for developing therapeutic targets in the field of endodontics. Here we comprehensively review recent finding on the PRRs and the mechanisms by which innate immunity is activated. We focus on the PRRs expressed on dental pulp and periapical tissues and their role in dental pulp inflammation.

  11. A Hyaluronan-Based Scaffold for the in Vitro Construction of Dental Pulp-Like Tissue

    Directory of Open Access Journals (Sweden)

    Letizia Ferroni

    2015-03-01

    Full Text Available Dental pulp tissue supports the vitality of the tooth, but it is particularly vulnerable to external insults, such as mechanical trauma, chemical irritation or microbial invasion, which can lead to tissue necrosis. In the present work, we present an endodontic regeneration method based on the use of a tridimensional (3D hyaluronan scaffold and human dental pulp stem cells (DPSCs to produce a functional dental pulp-like tissue in vitro. An enriched population of DPSCs was seeded onto hyaluronan-based non-woven meshes in the presence of differentiation factors to induce the commitment of stem cells to neuronal, glial, endothelial and osteogenic phenotypes. In vitro experiments, among which were gene expression profiling and immunofluorescence (IF staining, proved the commitment of DPSCs to the main components of dental pulp tissue. In particular, the hyaluronan-DPSCs construct showed a dental pulp-like morphology consisting of several specialized cells growing inside the hyaluronan fibers. Furthermore, these constructs were implanted into rat calvarial critical-size defects. Histological analyses and gene expression profiling performed on hyaluronan-DPSCs grafts showed the regeneration of osteodentin-like tissue. Altogether, these data suggest the regenerative potential of the hyaluronan-DPSC engineered tissue.

  12. A hyaluronan-based scaffold for the in vitro construction of dental pulp-like tissue.

    Science.gov (United States)

    Ferroni, Letizia; Gardin, Chiara; Sivolella, Stefano; Brunello, Giulia; Berengo, Mario; Piattelli, Adriano; Bressan, Eriberto; Zavan, Barbara

    2015-03-02

    Dental pulp tissue supports the vitality of the tooth, but it is particularly vulnerable to external insults, such as mechanical trauma, chemical irritation or microbial invasion, which can lead to tissue necrosis. In the present work, we present an endodontic regeneration method based on the use of a tridimensional (3D) hyaluronan scaffold and human dental pulp stem cells (DPSCs) to produce a functional dental pulp-like tissue in vitro. An enriched population of DPSCs was seeded onto hyaluronan-based non-woven meshes in the presence of differentiation factors to induce the commitment of stem cells to neuronal, glial, endothelial and osteogenic phenotypes. In vitro experiments, among which were gene expression profiling and immunofluorescence (IF) staining, proved the commitment of DPSCs to the main components of dental pulp tissue. In particular, the hyaluronan-DPSCs construct showed a dental pulp-like morphology consisting of several specialized cells growing inside the hyaluronan fibers. Furthermore, these constructs were implanted into rat calvarial critical-size defects. Histological analyses and gene expression profiling performed on hyaluronan-DPSCs grafts showed the regeneration of osteodentin-like tissue. Altogether, these data suggest the regenerative potential of the hyaluronan-DPSC engineered tissue.

  13. MASS BALANCE OF SILICA IN STRAW FROM THE PERSPECTIVE OF SILICA REDUCTION IN STRAW PULP

    Directory of Open Access Journals (Sweden)

    Celil Atik,

    2012-06-01

    Full Text Available The high silica content of wheat straw is an important limiting factor for straw pulping. High silica content complicates processing and black liquor recovery, wears out factory installations, and lowers paper quality. Each section of wheat straw has different cells and chemical compositions and thus different silica content. In this work, the silica content of balled straw samples were examined according to their physical components, including internodes, nodes, leaves (sheath and blade, rachis, grain, other plant bodies, and other plant spikes. Mass distribution of silica was determined by a dry ashing method. Half (50.90% of the silica comes from leaves, and its mechanical separation will reduce the silica content in wheat straw pulp significantly. Destroying silica bodies by sonication will increase the strength properties of straw pulp.

  14. Enzymatic pulp upgrade for producing high-value cellulose out of a Kraft paper pulp.

    Science.gov (United States)

    Hutterer, Christian; Kliba, Gerhard; Punz, Manuel; Fackler, Karin; Potthast, Antje

    2017-07-01

    The high-yield separation of polymeric parts from wood-derived lignocellulosic material is indispensable in biorefinery concepts. For the separation of cellulose and xylan from hardwood paper pulps to obtain pulps of high cellulose contents, simple alkaline extractions were found to be the most suitable technology, although having certain limitations. These are embodied by residual alkali resistant xylan incorporated in the pulp matrix. Further purification in order to produce pure cellulose with a low uniformity could be achieved selectively degrading residual xylan and depolymerizing the cellulose macromolecules by xylanase and cellulase. The latter help to adjust cellulose chain lengths for certain dissolving pulp grades while reducing the demand for ozone in subsequent TCF bleaching. Experiments applying different commercially available enzyme preparations revealed the dependency of xylanase performance on the residual xylan content in pulps being stimulated by additional cellulase usage. The action of the latter strongly depends on the cellulose allomorphy confirming the impact of the pulp morphology. Hence, the combined application of both types of enzymes offers a high potential for upgrading pulps in order to produce a pure and high-value cellulose product. Copyright © 2017 Elsevier Inc. All rights reserved.

  15. Mechanosensitivity of dental pulp stem cells is related to their osteogenic maturity

    NARCIS (Netherlands)

    Kraft, D.C.E.; Bindslev, D.A.; Melsen, B.; Abdallah, B.M.; Kassem, K.; Klein-Nulend, J.

    2010-01-01

    For engineering bone tissue, mechanosensitive cells are needed for bone (re)modelling. Local bone mass and architecture are affected by mechanical loading, which provokes a cellular response via loading-induced interstitial fluid flow. We studied whether human dental pulp-derived mesenchymal stem

  16. Preparation and Characterization of Cellulose Nanofibers from Two Commercial Hardwood and Softwood Pulps

    DEFF Research Database (Denmark)

    Stelte, Wolfgang; Sanadi, Anand R.

    2009-01-01

    The aim of this work was to study the mechanical fibrillation process for the preparation of cellulose nanofibers from two commercial hard- and softwood cellulose pulps. The process consisted of initial refining and subsequent high-pressure homogenization. The progress in fibrillation was studied...

  17. Innervated boomerang flap for finger pulp reconstruction.

    Science.gov (United States)

    Chen, Shao-Liang; Chiou, Tai-Fung

    2007-11-01

    The boomerang flap originates from the dorsolateral aspect of the proximal phalanx of an adjacent digit and is supplied by the retrograde blood flow through the vascular arcades between the dorsal and palmar digital arteries. To provide sensation of the boomerang flap for finger pulp reconstruction, the dorsal sensory branch of the proper digital nerve and the superficial sensory branch of the corresponding radial or ulnar nerve are included within the skin flap. After transfer of the flap to the injured site, epineural neurorrhaphies are done between the digital nerves of the pulp and the sensory branches of the flap. We used this sensory flap in five patients, with more than 1 year follow-up, and all patients achieved measurable two-points discrimination. The boomerang flap not only preserves the proper palmar digital artery but also provides an extended and innervated skin paddle. It seems to be an alternative choice for one-stage reconstruction of major pulp defect.

  18. Integrated chemical plants at the pulp mill

    Energy Technology Data Exchange (ETDEWEB)

    Ehtonen, P.; Hurme, M.; Jaervelaeinen, M.

    1995-12-31

    The goal of this paper is to present how the chemical plants can be integrated to the pulp mill. The integration renders possible to balance the chemical consumptions. The total mass balance of a pulp mill with the incoming fuel material and the outgoing waste and flue gases are discussed. The balance figures are presented for the chemicals of the modern fibre line, which will produce fully bleached softwood pulp with an improved effluent quality. The main benefits are lower chemical and transportation costs. The principal over-all plant process block diagrams and process descriptions are presented. The presented info system provides real time information on process and production status at overall mill and department levels. (author)

  19. Sisal organosolv pulp as reinforcement for cement based composites

    OpenAIRE

    Joaquim, Ana Paula; Tonoli, Gustavo Henrique Denzin; Santos, Sérgio Francisco Dos; Savastano Junior, Holmer

    2009-01-01

    The present work describes non-conventional sisal (Agave sisalana) chemical (organosolv) pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP) fibres were produced by the slurry de-watering and pressin...

  20. Effects of transportation time after extraction on the magnetic cryopreservation of pulp cells of rat dental pulp

    Directory of Open Access Journals (Sweden)

    Mao-Suan Huang

    2011-03-01

    Conclusions: The freezing technique used in this animal study provided positive effects on pulp cell storage. In addition, the storage time before the freezing procedure is an important issue for cryopreserving pulp cells in intact teeth.

  1. 78 FR 31315 - Kraft Pulp Mills NSPS Review

    Science.gov (United States)

    2013-05-23

    ... Kraft Pulp Mills NSPS Review; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 100 / Thursday, May...-OAR-2012-0640; FRL-9815-9] RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection... performance standards for kraft pulp mills. These revised standards include particulate matter emission limits...

  2. Comparative study of percentage yield of pulp from various Nigerian ...

    African Journals Online (AJOL)

    user

    also other applications like in the chemical industry. (Biermann, 1993). Therefore pulp is a very .... digester was maintained at an operating condition of. 170°C, pressure of 2 bars, with liquor to wood ratio of 4:1. Cooking ... The effects of different concentrations of pulping liquor on the yield of pulp from the wood species are ...

  3. Organosolv pulping and test paper characterization of fiber hemp

    NARCIS (Netherlands)

    Zomers, F.H.A.; Gosselink, R.J.A.; Dam, van J.E.G.; Tjeerdsma, B.F.

    1995-01-01

    The autocatalyzed ethanol pulping of hemp to produce chemical-grade pulp was examined. Batch delignification conditions were developed for hemp core, hemp bast, and hemp whole stem. Although successful pulping of both hemp core and bast fibre is possible, further research is necessary.

  4. Betatron activation analysis of cupriferous flotation pulp

    International Nuclear Information System (INIS)

    Kaminski, R.; Matenko, J.; Mencel, J.; Janiczek, J.; Kielsznia, J.

    1974-01-01

    A method of copper determination in cupriferous flotation pulp by photo-activation analysis using betatron and another equipments of existent ''analytical line'' intended for copper determination in dry samples has been described. An activation has been achieved with 14.9 MeV γ-photons. The excitation activity was investigated by using two scintillation detectors and a fast coincidence circuit with resolution time 80 ns. The precision of method was determined as +- 4.25% in 0.95 confidence level for pulp with concentration 5% Cu and +- 24% for 0.06% Cu. (author)

  5. Plasma lipoproteins as mediators of the oxidative stress induced by UV light in human skin: a review of biochemical and biophysical studies on mechanisms of apolipoprotein alteration, lipid peroxidation, and associated skin cell responses.

    Science.gov (United States)

    Filipe, Paulo; Morlière, Patrice; Silva, João N; Mazière, Jean-Claude; Patterson, Larry K; Freitas, João P; Santus, R

    2013-01-01

    There are numerous studies concerning the effect of UVB light on skin cells but fewer on other skin components such as the interstitial fluid. This review highlights high-density lipoprotein (HDL) and low-density lipoprotein (LDL) as important targets of UVB in interstitial fluid. Tryptophan residues are the sole apolipoprotein residues absorbing solar UVB. The UVB-induced one-electron oxidation of Trp produces (•)Trp and (•)O2 (-) radicals which trigger lipid peroxidation. Immunoblots from buffered solutions or suction blister fluid reveal that propagation of photooxidative damage to other residues such as Tyr or disulfide bonds produces intra- and intermolecular bonds in apolipoproteins A-I, A-II, and B100. Partial repair of phenoxyl tyrosyl radicals (TyrO(•)) by α -tocopherol is observed with LDL and HDL on millisecond or second time scales, whereas limited repair of α -tocopherol by carotenoids occurs in only HDL. More effective repair of Tyr and α -tocopherol is observed with the flavonoid, quercetin, bound to serum albumin, but quercetin is less potent than new synthetic polyphenols in inhibiting LDL lipid peroxidation or restoring α -tocopherol. The systemic consequences of HDL and LDL oxidation and the activation and/or inhibition of signalling pathways by oxidized LDL and their ability to enhance transcription factor DNA binding activity are also reviewed.

  6. Plasma Lipoproteins as Mediators of the Oxidative Stress Induced by UV Light in Human Skin: A Review of Biochemical and Biophysical Studies on Mechanisms of Apolipoprotein Alteration, Lipid Peroxidation, and Associated Skin Cell Responses

    Directory of Open Access Journals (Sweden)

    Paulo Filipe

    2013-01-01

    Full Text Available There are numerous studies concerning the effect of UVB light on skin cells but fewer on other skin components such as the interstitial fluid. This review highlights high-density lipoprotein (HDL and low-density lipoprotein (LDL as important targets of UVB in interstitial fluid. Tryptophan residues are the sole apolipoprotein residues absorbing solar UVB. The UVB-induced one-electron oxidation of Trp produces •Trp and O2•- radicals which trigger lipid peroxidation. Immunoblots from buffered solutions or suction blister fluid reveal that propagation of photooxidative damage to other residues such as Tyr or disulfide bonds produces intra- and intermolecular bonds in apolipoproteins A-I, A-II, and B100. Partial repair of phenoxyl tyrosyl radicals (TyrO• by α-tocopherol is observed with LDL and HDL on millisecond or second time scales, whereas limited repair of α-tocopherol by carotenoids occurs in only HDL. More effective repair of Tyr and α-tocopherol is observed with the flavonoid, quercetin, bound to serum albumin, but quercetin is less potent than new synthetic polyphenols in inhibiting LDL lipid peroxidation or restoring α-tocopherol. The systemic consequences of HDL and LDL oxidation and the activation and/or inhibition of signalling pathways by oxidized LDL and their ability to enhance transcription factor DNA binding activity are also reviewed.

  7. Effects of Soda-Anthraquinone Pulping Variables on the Durian Rind Pulp and Paper Characteristics: A Preliminary Test

    Science.gov (United States)

    Rizal Masrol, Shaiful; Irwan Ibrahim, Mohd Halim; Adnan, Sharmiza; Rahmad Talib, Mohd; Sian, Lau Lee

    2017-08-01

    Good combination of pulping variables is required to obtain the quality pulp and paper characteristics. Thus, in this preliminary work, naturally dried durian rind were pulped under Soda-Anthraquinone (Soda-AQ) pulping process with 18% to 22% alkali charge, 0% to 0.1% Anthraquinone (AQ) charge, 90 minutes to 150 minutes of cooking time and 150°C to 170°C to investigate the effect of pulping variables on the characteristics of the pulp and paper. Pulping condition with 0% of AQ charge was also conducted for comparison. Results indicated that the best screen yield percentage, reject yield percentage, freeness, drainage time, tear index, number of folds and optical properties were shown by the pulp produced with combination of the highest active alkali (22%), AQ charge (0.1%), cooking time (150 minutes) and cooking temperature (170°C) except apparent density, tensile index and burst index. This preliminary result shows that the optimum quality of durian rind pulp as a potential papermaking raw material pulp could be produced by selecting the good combination of pulping variables which influences the pulp and paper characteristics.

  8. Detection of hydrogen peroxide with graphyne

    Science.gov (United States)

    Majidi, R.; Karami, A. R.

    2013-12-01

    The effect of hydrogen peroxide on the electronic properties of graphyne has been investigated to explore the possibility of using graphyne based biosensor. We have used density functional theory to study the electronic properties of γ-graphyne in the presence of different number of hydrogen peroxide. The optimal adsorption position, orientation, and distance of hydrogen peroxide adsorbed on the graphyne sheet have been determined by calculating adsorption energy. It is found that γ-graphyne which is an intrinsic semiconductor becomes an n-type semiconductor due to the presence of hydrogen peroxide. The energy band gap of γ-graphyne is decreased by increasing the number of hydrogen peroxide. The results demonstrate that γ-graphyne is a promising candidate for biosensor application because of its electrical sensitivity to hydrogen peroxide.

  9. A theranostic dental pulp capping agent with improved MRI and CT contrast and biological properties.

    Science.gov (United States)

    Mastrogiacomo, S; Güvener, N; Dou, W; Alghamdi, H S; Camargo, W A; Cremers, J G O; Borm, P J A; Heerschap, A; Oosterwijk, E; Jansen, J A; Walboomers, X F

    2017-10-15

    Different materials have been used for vital dental pulp treatment. Preferably a pulp capping agent should show appropriate biological performance, excellent handling properties, and a good imaging contrast. These features can be delivered into a single material through the combination of therapeutic and diagnostic agents (i.e. theranostic). Calcium phosphate based composites (CPCs) are potentially ideal candidate for pulp treatment, although poor imaging contrast and poor dentino-inductive properties are limiting their clinical use. In this study, a theranostic dental pulp capping agent was developed. First, imaging properties of the CPC were improved by using a core-shell structured dual contrast agent (csDCA) consisting of superparamagnetic iron oxide (SPIO) and colloidal gold, as MRI and CT contrast agent respectively. Second, biological properties were implemented by using a dentinogenic factor (i.e. bone morphogenetic protein 2, BMP-2). The obtained CPC/csDCA/BMP-2 composite was tested in vivo, as direct pulp capping agent, in a male Habsi goat incisor model. Our outcomes showed no relevant alteration of the handling and mechanical properties (e.g. setting time, injectability, and compressive strength) by the incorporation of csDCA particles. In vivo results proved MRI contrast enhancement up to 7weeks. Incisors treated with BMP-2 showed improved tertiary dentin deposition as well as faster cement degradation as measured by µCT assessment. In conclusion, the presented theranostic agent matches the imaging and regenerative requirements for pulp capping applications. In this study, we combined diagnostic and therapeutic agents in order to developed a theranostic pulp capping agent with enhanced MRI and CT contrast and improved dentin regeneration ability. In our study we cover all the steps from material preparation, mechanical and in vitro characterization, to in vivo study in a goat dental model. To the best of our knowledge, this is the first time that a

  10. PEROXIDE PROCESS FOR SEPARATION OF RADIOACTIVE MATERIALS

    Science.gov (United States)

    Seaborg, G.T.; Perlman, I.

    1958-09-16

    reduced state, from hexavalent uranium. It consists in treating an aqueous solution containing such uranium and plutonium ions with sulfate ions in order to form a soluble uranium sulfate complex and then treating the solution with a soluble thorium compound and a soluble peroxide compound in order to ferm a thorium peroxide carrier precipitate which carries down with it the plutonium peroxide present. During this treatment the pH of the solution must be maintained between 2 and 3.

  11. Method for rapidly determining a pulp kappa number using spectrophotometry

    Science.gov (United States)

    Chai, Xin-Sheng; Zhu, Jun Yong

    2002-01-01

    A system and method for rapidly determining the pulp kappa number through direct measurement of the potassium permanganate concentration in a pulp-permanganate solution using spectrophotometry. Specifically, the present invention uses strong acidification to carry out the pulp-permanganate oxidation reaction in the pulp-permanganate solution to prevent the precipitation of manganese dioxide (MnO.sub.2). Consequently, spectral interference from the precipitated MnO.sub.2 is eliminated and the oxidation reaction becomes dominant. The spectral intensity of the oxidation reaction is then analyzed to determine the pulp kappa number.

  12. Effect of Urea Addition on Soda Pulping of Oak Wood

    OpenAIRE

    Cho, Nam-Seok; Matsumoto, Yuji; Cho, Hee-Yeon; Shin, Soo-Jeong; Oga, Shoji

    2008-01-01

    Many studies have been conducted to find a sulfur-free additive for alkaline pulping liquors that would have an effect similar to that of sulfide in kraft pulping. Some reagents that partially fulfill this role have been found, but they are too expensive to be used in the quantities required to make them effective. As an alternative method to solve air pollution problem and difficulty of pulp bleaching of kraft pulping process, NaOH-Urea pulping was applied. The properties of NaOH-Urea pul...

  13. Characterization of Coronal Pulp Cells and Radicular Pulp Cells in Human Teeth.

    Science.gov (United States)

    Honda, Masaki; Sato, Momoko; Toriumi, Taku

    2017-09-01

    Dental pulp has garnered much attention as an easily accessible postnatal tissue source of high-quality mesenchymal stem cells (MSCs). Since the discovery of dental pulp stem cells (DPSCs) in permanent third molars, stem cells from human exfoliated deciduous teeth and from supernumerary teeth (mesiodentes) have been identified as a population distinct from DPSCs. Dental pulp is divided into 2 parts based on the developing stage: the coronal pulp and the radicular pulp. Root formation begins after the crown part is completed. We performed a sequential study to examine the differences between the characteristics of coronal pulp cells (CPCs) and radicular pulp cells (RPCs) from permanent teeth, mesiodentes, and deciduous teeth. Interestingly, although we have not obtained any data on the difference between CPCs and RPCs in permanent teeth, there are some differences between the characteristics of CPCs and RPCs from mesiodentes and deciduous teeth. The MSC characteristics differed between the RPCs and CPCs, and the reprogramming efficiency for the generation of induced pluripotent stem cells was greater in RPCs than in CPCs from deciduous teeth. The proportion of CD105 + cells in CPCs versus that in RPCs varied in mesiodentes but not in permanent teeth. The results indicate that the proportion of CD105 + cells is an effective means of characterizing dental pulp cells in mesiodentes. Taken together, the stem cells in deciduous and supernumerary teeth share many characteristics, such as a high proliferation rate and an immunophenotype similar to that of DPSCs. Thus, mesiodentes accidentally encountered on radiographs by the general dental practitioner might be useful for stem cell therapy. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  14. Pulp and paper from oil palm fronds: Wavelet neural networks modeling of soda-ethanol pulping

    OpenAIRE

    Zarita Zainuddin; Wan Rosli Wan Daud; Pauline Ong; Amran Shafie

    2012-01-01

    Wavelet neural networks (WNNs) were used to investigate the influence of operational variables in the soda-ethanol pulping of oil palm fronds (viz. NaOH concentration (10-30%), ethanol concentration (15-75%), cooking temperature (150-190 ºC), and time (60-180 min)) on the resulting pulp and paper properties (viz. screened yield, kappa number, tensile index, and tear index). Performance assessments demonstrated the predictive capability of WNNs, in that the experimental results of the dependen...

  15. Overoxidation of chloroplast 2-Cys peroxiredoxins: balancing toxic and signaling activities of hydrogen peroxide

    Directory of Open Access Journals (Sweden)

    Leonor ePuerto-Galán

    2013-08-01

    Full Text Available Photosynthesis, the primary source of biomass and oxygen into the biosphere, involves the transport of electrons in the presence of oxygen and, therefore, chloroplasts constitute an important source of reactive oxygen species (ROS, including hydrogen peroxide. If accumulated at high level, hydrogen peroxide may exert a toxic effect; however, it is as well an important second messenger. In order to balance the toxic and signaling activities of hydrogen peroxide its level has to be tightly controlled. To this end, chloroplasts are equipped with different antioxidant systems such as 2-Cys peroxiredoxins (2-Cys Prxs, thiol-based peroxidases able to reduce hydrogen- and organic peroxides. At high peroxide concentrations the peroxidase function of 2-Cys Prxs may become inactivated through a process of overoxidation. This inactivation has been proposed to explain the signaling function of hydrogen peroxide in eukaryotes, whereas in prokaryotes, the 2-Cys Prxs of which were considered to be insensitive to overoxidation, the signaling activity of hydrogen peroxide is less relevant. Here we discuss the current knowledge about the mechanisms controlling 2-Cys Prx overoxidation in chloroplasts, organelles with an important signaling function in plants. Given the prokaryotic origin of chloroplasts, we discuss the occurrence of 2-Cys Prx overoxidation in cyanobacteria with the aim of identifying similarities between chloroplasts and their ancestors regarding their response to hydrogen peroxide.

  16. Enrichment of coal pulps by selective flocculation

    Energy Technology Data Exchange (ETDEWEB)

    Blaschke, Z

    1977-01-01

    The results are presented of selective flocculation of coal pulps using different reagents. In some tests the coal particles were flocculated, and in others the coal remained in suspension and the dirt was flocculated. Selective flocculation makes it possible to obtain coal concentrates with a very low ash content from slurries with a high ash content. (In Polish)

  17. Enrichment of coal pulps by selective flocculation

    Energy Technology Data Exchange (ETDEWEB)

    Blaschke, Z

    1977-01-01

    The results are presented of selective flocculation of coal pulps using different reagents. In some tests the coal particles were flocculated, and in others the coal remained in suspension and the dirt was flocculated. Selective flocculation makes it possible to obtain coal concentrates with a very low ash content from slurries with a high ash content.

  18. Pulp regeneration by transplantation of dental pulp stem cells in pulpitis: a pilot clinical study.

    Science.gov (United States)

    Nakashima, Misako; Iohara, Koichiro; Murakami, Masashi; Nakamura, Hiroshi; Sato, Yayoi; Ariji, Yoshiko; Matsushita, Kenji

    2017-03-09

    Experiments have previously demonstrated the therapeutic potential of mobilized dental pulp stem cells (MDPSCs) for complete pulp regeneration. The aim of the present pilot clinical study is to assess the safety, potential efficacy, and feasibility of autologous transplantation of MDPSCs in pulpectomized teeth. Five patients with irreversible pulpitis were enrolled and monitored for up to 24 weeks following MDPSC transplantation. The MDPSCs were isolated from discarded teeth and expanded based on good manufacturing practice (GMP). The quality of the MDPSCs at passages 9 or 10 was ascertained by karyotype analyses. The MDPSCs were transplanted with granulocyte colony-stimulating factor (G-CSF) in atelocollagen into pulpectomized teeth. The clinical and laboratory evaluations demonstrated no adverse events or toxicity. The electric pulp test (EPT) of the pulp at 4 weeks demonstrated a robust positive response. The signal intensity of magnetic resonance imaging (MRI) of the regenerated tissue in the root canal after 24 weeks was similar to that of normal dental pulp in the untreated control. Finally, cone beam computed tomography demonstrated functional dentin formation in three of the five patients. Human MDPSCs are safe and efficacious for complete pulp regeneration in humans in this pilot clinical study.

  19. Radiation -adsorption treatment of pesticides by using wood pulp and bagasse pulp

    International Nuclear Information System (INIS)

    Abd El-Aal, S.E.; Sokker, S.S.; Dessooki, A.M.

    2005-01-01

    Alkaline pulping of pulp wood and bagasse using sodium hydroxide resulted in the reduction of lignin from the wood and bagasse fibers and consequently increase adsorption of the pesticide pollutants to these fibers. Three different types of pesticides were used in this study namely, metalaxyl, dicloran and arelon. which were irradiated at a dose of 4 kGy before adsorption treatment.The results show that moderate adsorption was observed for all pesticides when adsorption was carried out without alkaline pulping and irradiation. This is due to the presence of lignin which retard the adsorption process. Batch sorption experiments at different pH values (3, 7, 9) for the retention of these pesticides by pulp wood and pulp bagasse fibers indicated that sorption is governed by the interaction of the ionized form of these compounds with the polyhydroxyl structure of cellulose. The study shows that alkaline pulping of pulpwood and bagasse improves its ability towards adsorption of the radiation degraded pesticide molecules

  20. DPSCs from Inflamed Pulp Modulate Macrophage Function via the TNF-α/IDO Axis

    Science.gov (United States)

    Lee, S.; Zhang, Q.Z.; Karabucak, B.; Le, A.D.

    2016-01-01

    Human dental pulp stem cells (DPSCs) can be isolated from inflamed pulp derived from carious teeth with symptomatic irreversible pulpitis (I-DPSCs), which possess stemness and multidifferentiation potentials similar to DPSCs from healthy pulp. Since macrophages—essential cell players of the pulpal innate immunity—can regulate pulpal inflammation and repair, the authors investigated the immunomodulatory effects of DPSCs/I-DPSCs on macrophage functions and their underlying mechanisms. Similar to DPSCs, I-DPSCs were capable of colony-forming efficiency and adipogenic and osteo/dentinogenic differentiation under in vitro induction conditions. I-DPSCs also expressed a similar phenotypic profile of mesenchymal stem cell markers, except a relatively higher level of CD146 as compared with DPSCs. Coculture of DPSCs or I-DPSCs with differentiated THP-1 cells, the human monocyte cell line, markedly suppressed tumor necrosis factor α (TNF-α) secretion in response to stimulation with lipopolysaccharides (LPS) and/or nigericin. However, unlike TNF-α, the secreted level of interleukin 1β was not affected by coculture with DPSCs or I-DPSCs. Furthermore, DPSC/I-DPSC-mediated inhibition of TNF-α secretion by macrophages was abolished by pretreatment with 1-methyl-D-tryptophan, a specific inhibitor of indoleamine-pyrrole 2,3-dioxygenase (IDO), but not by NSC-398, a specific inhibitor of COX-2, suggesting IDO as a mediator. Interestingly, IDO expression was significantly augmented in macrophages and mesenchymal stromal cells in inflamed human pulp tissues. Collectively, these findings show that I-DPSCs, similar to DPSCs, possess stem cell properties and suppress macrophage functions via the TNF-α/IDO axis, thereby providing a physiologically relevant context for their innate immunomodulatory activity in the dental pulp and their capability for pulp repair. PMID:27384335

  1. DPSCs from Inflamed Pulp Modulate Macrophage Function via the TNF-α/IDO Axis.

    Science.gov (United States)

    Lee, S; Zhang, Q Z; Karabucak, B; Le, A D

    2016-10-01

    Human dental pulp stem cells (DPSCs) can be isolated from inflamed pulp derived from carious teeth with symptomatic irreversible pulpitis (I-DPSCs), which possess stemness and multidifferentiation potentials similar to DPSCs from healthy pulp. Since macrophages-essential cell players of the pulpal innate immunity-can regulate pulpal inflammation and repair, the authors investigated the immunomodulatory effects of DPSCs/I-DPSCs on macrophage functions and their underlying mechanisms. Similar to DPSCs, I-DPSCs were capable of colony-forming efficiency and adipogenic and osteo/dentinogenic differentiation under in vitro induction conditions. I-DPSCs also expressed a similar phenotypic profile of mesenchymal stem cell markers, except a relatively higher level of CD146 as compared with DPSCs. Coculture of DPSCs or I-DPSCs with differentiated THP-1 cells, the human monocyte cell line, markedly suppressed tumor necrosis factor α (TNF-α) secretion in response to stimulation with lipopolysaccharides (LPS) and/or nigericin. However, unlike TNF-α, the secreted level of interleukin 1β was not affected by coculture with DPSCs or I-DPSCs. Furthermore, DPSC/I-DPSC-mediated inhibition of TNF-α secretion by macrophages was abolished by pretreatment with 1-methyl-D-tryptophan, a specific inhibitor of indoleamine-pyrrole 2,3-dioxygenase (IDO), but not by NSC-398, a specific inhibitor of COX-2, suggesting IDO as a mediator. Interestingly, IDO expression was significantly augmented in macrophages and mesenchymal stromal cells in inflamed human pulp tissues. Collectively, these findings show that I-DPSCs, similar to DPSCs, possess stem cell properties and suppress macrophage functions via the TNF-α/IDO axis, thereby providing a physiologically relevant context for their innate immunomodulatory activity in the dental pulp and their capability for pulp repair. © International & American Associations for Dental Research 2016.

  2. Cellulose, hemicelluloses, lignin and ash content of some organic materials and their suitability for use as paper pulp supplements.

    Science.gov (United States)

    Ververis, C; Georghiou, K; Danielidis, D; Hatzinikolaou, D G; Santas, P; Santas, R; Corleti, V

    2007-01-01

    Freshwater algal biomass and orange and lemon peels were assessed as tissue paper pulp supplements. Cellulose and hemicellulose contents of algal biomass were 7.1% and 16.3%, respectively, whereas for citrus peels cellulose content ranged from 12.7% to 13.6% and hemicellulose from 5.3% to 6.1%. For all materials, lignin and ash content was 2% or lower, rendering them suitable for use as paper pulp supplements. The addition of algal biomass to paper pulp increased its mechanical strength significantly. However, brightness was adversely affected by chlorophyll. The addition of citrus peels in paper pulp had no effect on breaking length, increased bursting strength and decreased tearing resistance. Brightness was negatively affected at proportions of 10%, because citrus peel particles behave as coloured pigments. The cost of both materials is about 45% lower than that of conventional pulp, resulting in a 0.9-4.5% reduction in final paper price upon their addition to the pulp.

  3. A Novel Strategy to Engineer Pre-Vascularized Full-Length Dental Pulp-like Tissue Constructs.

    Science.gov (United States)

    Athirasala, Avathamsa; Lins, Fernanda; Tahayeri, Anthony; Hinds, Monica; Smith, Anthony J; Sedgley, Christine; Ferracane, Jack; Bertassoni, Luiz E

    2017-06-12

    The requirement for immediate vascularization of engineered dental pulp poses a major hurdle towards successful implementation of pulp regeneration as an effective therapeutic strategy for root canal therapy, especially in adult teeth. Here, we demonstrate a novel strategy to engineer pre-vascularized, cell-laden hydrogel pulp-like tissue constructs in full-length root canals for dental pulp regeneration. We utilized gelatin methacryloyl (GelMA) hydrogels with tunable physical and mechanical properties to determine the microenvironmental conditions (microstructure, degradation, swelling and elastic modulus) that enhanced viability, spreading and proliferation of encapsulated odontoblast-like cells (OD21), and the formation of endothelial monolayers by endothelial colony forming cells (ECFCs). GelMA hydrogels with higher polymer concentration (15% w/v) and stiffness enhanced OD21 cell viability, spreading and proliferation, as well as endothelial cell spreading and monolayer formation. We then fabricated pre-vascularized, full-length, dental pulp-like tissue constructs by dispensing OD21 cell-laden GelMA hydrogel prepolymer in root canals of extracted teeth and fabricating 500 µm channels throughout the root canals. ECFCs seeded into the microchannels successfully formed monolayers and underwent angiogenic sprouting within 7 days in culture. In summary, the proposed approach is a simple and effective strategy for engineering of pre-vascularized dental pulp constructs offering potentially beneficial translational outcomes.

  4. Effects of mineral trioxide aggregate and formocresol on vital pulp after pulpotomy of primary molars: An in vivo study

    Directory of Open Access Journals (Sweden)

    Brinda Godhi

    2011-01-01

    Full Text Available Background: Preservation of pulp vitality is of utmost importance to the normal physiological functioning of tooth in situ and physiological process of exfoliation in a tooth affected by disease or trauma. Pulpotomy serves such a purpose using various medicaments applied directly on vital pulp. Aim: The aim of this study was to evaluate clinically and radiographically the effects of mineral trioxide aggregate (MTA and formocresol (FC as a pulp dressing after coronal pulp amputation (pulpotomy in primary molars prospectively over a period of 1 year. Materials and Methods: Thirty-three healthy children, aged between 5 and 8 years, requiring pulp therapy were selected after clinical and radiographic assessment. A total of 50 maxillary and mandibular primary molars were treated by the conventional pulpotomy technique. The teeth were divided into two equal groups. In Group A, FC was used as the pulp dressing agent, and in Group B, MTA was used before restoration with stainless steel crowns. The research employed was a prospective study. The teeth treated were assessed postoperatively after 1, 3, 6 and 12 months. The observations were tabulated and statistically analyzed. Results: Clinically, both the groups showed 100% success at 1, 3, 6 and 12 months. At 3 months, the radiographic success rates of FC and MTA were 92% and 96%, respectively, and at 6 and 12 months, the radiographic success rates of FC and MTA were 88% and 96%, respectively. Conclusion: MTA showed a higher success rate than FC and may be a favorable material for pulpotomy in primary molars whose pulps have been compromised by a carious or mechanical pulp exposure

  5. Potassium hydroxide pulping of rice straw in biorefinery initiatives.

    Science.gov (United States)

    Jahan, M Sarwar; Haris, Fahmida; Rahman, M Mostafizur; Samaddar, Purabi Rani; Sutradhar, Shrikanta

    2016-11-01

    Rice straw is supposed to be one of the most important lignocellulosic raw materials for pulp mill in Asian countries. The major problem in rice straw pulping is silica. The present research is focused on the separation of silica from the black liquor of rice straw pulping by potassium hydroxide (KOH) and pulp evaluation. Optimum KOH pulping conditions of rice straw were alkali charge 12% as NaOH, cooking temperature 150°C for 2h and material to liquor ratio, 1:6. At this condition pulp yield was 42.4% with kappa number 10.3. KOH pulp bleached to 85% brightness by D0EpD1 bleaching sequences with ClO2 consumption of 25kg/ton of pulp. Silica and lignin were separated from the black liquor of KOH pulping. The amount of recovered silica, lignin and hemicelluloses were 10.4%, 8.4% and 13.0%. The papermaking properties of KOH pulp from rice straw were slightly better than those of corresponding NaOH pulp. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Characterization and Degradation of Pectic Polysaccharides in Cocoa Pulp.

    Science.gov (United States)

    Meersman, Esther; Struyf, Nore; Kyomugasho, Clare; Jamsazzadeh Kermani, Zahra; Santiago, Jihan Santanina; Baert, Eline; Hemdane, Sami; Vrancken, Gino; Verstrepen, Kevin J; Courtin, Christophe M; Hendrickx, Marc; Steensels, Jan

    2017-11-08

    Microbial fermentation of the viscous pulp surrounding cocoa beans is a crucial step in chocolate production. During this process, the pulp is degraded, after which the beans are dried and shipped to factories for further processing. Despite its central role in chocolate production, pulp degradation, which is assumed to be a result of pectin breakdown, has not been thoroughly investigated. Therefore, this study provides a comprehensive physicochemical analysis of cocoa pulp, focusing on pectic polysaccharides, and the factors influencing its degradation. Detailed analysis reveals that pectin in cocoa pulp largely consists of weakly bound substances, and that both temperature and enzyme activity play a role in its degradation. Furthermore, this study shows that pulp degradation by an indigenous yeast fully relies on the presence of a single gene (PGU1), encoding for an endopolygalacturonase. Apart from their basic scientific value, these new insights could propel the selection of microbial starter cultures for more efficient pulp degradation.

  7. TESTING OF PULP VITALITY BY PULSOXIMETRY

    Directory of Open Access Journals (Sweden)

    Gabriela CIOBANU

    2012-06-01

    Full Text Available The methods applied for diagnosing the health condition of the pulp tissue are numerous, however, nowadays, an increasingly higher number of conventional tests are replaced by some objective, non-invasive, painless and reliable tests. Among them, pulse oximetry is a method for the investigation of pulp vitality based on oxygen saturation (SaO2 of the hemoglobin from the blood present in the pulp vascular bed, as a means of differentiating among the vital and the non-vital teeth. In the present study, registrations were made on a group of 120 frontal maxillary teeth, in patients with ages between 20 and 40 years, on using a digital sensor modified by the pulse oximeter with which the pulse and the values of oxygen saturation were measured at the level of both teeth and right hand finger. The mean SaO2 value in the pulp blood of the vital teeth was of 83.30% for the central incisor, of 78.51% for the lateral one and of 84.56%, respectively, for the canine; the value recorded at finger level was of 97%. In the non-vital teeth, the SaO2 value measured on the pulse oximeter was of 0%. Pulse registration showed mean values of 70.56 beatings/min at tooth level and of 70.88 beatings/min, respectively, at finger level. The results of the present study may confirm that pulse oximetry represents a simple, non-traumatic, efficient and objective method for testing the vitality condition of the dental pulp.

  8. Evaluation of genotoxicity induced by hydrogen peroxide in the presence of ions chelator Fe2+ (2,2'-dipyridyl) and of Cu2+(neocuproine), in Escherichia coli: involvement of DNA repair mechanisms in the bacteria survival

    International Nuclear Information System (INIS)

    Almeida, Carlos Eduardo Bonacossa de

    1998-01-01

    Prior incubation of the E. coli cultures with the iron ions chelator 2,2'-dipyridyl (1 mM) caused an intensification of the lethality and the mutagenesis induced by the hydrogen peroxide, mainly at high concentrations (20 mM). It was also detected an enhancement of DNA strand breaks in this condition. The addition of the copper ions chelator neocuproine blocked partially this phenomenon. The enzymes XthA and Nfo act alternatively in the repair of the lesions induced by H 2 O 2 in the presence of 2,2'-dipyridyl. H 2 O 2 can act synergistically with neocuproine in killing E. coli, causing an enhancement in DNA strand breaks. The recombinational repair, the UvrABC excinuclease and Fpg function appeared to participate in the repair of the synergistic lesions. (author)

  9. Dental Pulp Revascularization of Necrotic Permanent Teeth with Immature Apices.

    Science.gov (United States)

    El Ashiry, Eman A; Farsi, Najat M; Abuzeid, Sawsan T; El Ashiry, Mohamed M; Bahammam, Hammam A

    The treatment of immature necrotic teeth with apical periodontitis presents challenges in endodontic and pediatric dentistry. Revascularization is a recent treatment for such cases as an alternative to conventional apexification. The purpose is to examine the effect of a pulpal revascularization procedure on immature necrotic teeth with apical periodontitis. Twenty patients were enrolled for pulp revascularization procedure by root canal disinfection using a triple antibiotic mixture for 1-2 weeks, followed by creating a blood clot, sealing the root canal orifice using white mineral trioxide aggregate and a coronal seal of composite resin. Patients were recalled periodically for up to 24 months. During follow-up, all patients were asymptomatic. Three cases of chronic apical periodontitis showed clinical disappearance of the sinus tract 2 weeks after treatment. Radiography revealed progressive periapical radiolucency resolution within the first 12 months. Within 12-24 months, the treated teeth showed progressive increases in dentinal wall thickness, root length and continued root development. Clinical and radiographic evidence showed successful revascularization treatments of immature necrotic permanent teeth with apical periodontitis. More studies are necessary to understand the underlying mechanisms and to perform histopathology of the pulp space contents after revascularization procedures.

  10. Human dental pulp stem cells with highly angiogenic and neurogenic potential for possible use in pulp regeneration.

    Science.gov (United States)

    Nakashima, Misako; Iohara, Koichiro; Sugiyama, Masahiko

    2009-01-01

    Dental caries is a common public health problem, causing early loss of dental pulp and resultant tooth loss. Dental pulp has important functions to sustain teeth providing nutrient and oxygen supply, innervation, reactionary/reparative dentin formation and immune response. Regeneration of pulp is an unmet need in endodontic therapy, and angiogenesis/vasculogenesis and neurogenesis are critical for pulp regeneration. Permanent and deciduous pulp tissue is easily available from teeth after extraction without ethical issues and has potential for clinical use. In this review, we introduce some stem cell subfractions, CD31(-)/CD146(-) SP cells and CD105(+) cells with high angiogenic and neurogenic potential, derived from human adult dental pulp tissue. Potential utility of these cells is addressed as a source of cells for treatment of cerebral and limb ischemia and pulp inflammation complete with angiogenesis and vasculogenesis.

  11. The corrosion of titanium and some other construction materials during hydrogen peroxide bleaching according to the field measurements

    Energy Technology Data Exchange (ETDEWEB)

    Hyoekyvirta, O.; Pohjanne, P.; Heinaevaara, A. [Oy METSA-BOTNIA Ab, Kaskinen' s mill, 64260 Kaskinen (Finland); Hirvonen, J. [VTT Automation, Industrial Automation, P.O. Box 1301, FIN-02044 (Finland); Lewenstam, A. [Center for Process Analytical Chemistry and Sensor Technology ' ProSens' Abo Akademi University, 20500 Abo (Finland)

    1999-07-01

    In a Finnish pulp mill, the field measurements of different materials were performed in different stages of peroxide bleaching: P{sub 1} and P{sub 2}. The field measurements were performed with three different sensors. The sensors were designed in co-operation with Valmet Automation Kajaani Oy. Each sensor measured the corrosion potential, the redox potential and the weight losses of three different materials. Simultaneously, the data of the most important parameters of bleaching, i.e. temperature, pH, peroxide flow rate and concentration, mass flow, consistency, residuals, flow rate and concentration of alkaline, were collected in the data logger by a dedicated program. The results proved that the corrosion of different materials (stainless steel S31654, nickel-based alloy N10276 and titanium Gr. 5) could be estimated with field experiments. The uniform corrosion of titanium occurred in a certain bleaching situation. The field measurements gave a good estimation of whether the material dissolved during process operation or process disorders. Our results clearly show that the mixing of the chemicals can be reliably estimated, and thus advantageous for a pulp mill. The materials studied withstood the bleaching significantly better if the chemicals were mixed directly with a pulp. Usually the chemicals are mixed with alkaline and then added to the pulp. The field measurements could also be applied in ozone and in the peracetic acid bleaching stage. The sensors can be utilized as tools during process monitoring or diagnostics. With the aid of monitoring it is possible to clarify how the different process operation models affect the corrosion of materials. (author)

  12. The corrosion of titanium and some other construction materials during hydrogen peroxide bleaching according to the field measurements

    International Nuclear Information System (INIS)

    Hyoekyvirta, O.; Pohjanne, P.; Heinaevaara, A.; Hirvonen, J.; Lewenstam, A.

    1999-01-01

    In a Finnish pulp mill, the field measurements of different materials were performed in different stages of peroxide bleaching: P 1 and P 2 . The field measurements were performed with three different sensors. The sensors were designed in co-operation with Valmet Automation Kajaani Oy. Each sensor measured the corrosion potential, the redox potential and the weight losses of three different materials. Simultaneously, the data of the most important parameters of bleaching, i.e. temperature, pH, peroxide flow rate and concentration, mass flow, consistency, residuals, flow rate and concentration of alkaline, were collected in the data logger by a dedicated program. The results proved that the corrosion of different materials (stainless steel S31654, nickel-based alloy N10276 and titanium Gr. 5) could be estimated with field experiments. The uniform corrosion of titanium occurred in a certain bleaching situation. The field measurements gave a good estimation of whether the material dissolved during process operation or process disorders. Our results clearly show that the mixing of the chemicals can be reliably estimated, and thus advantageous for a pulp mill. The materials studied withstood the bleaching significantly better if the chemicals were mixed directly with a pulp. Usually the chemicals are mixed with alkaline and then added to the pulp. The field measurements could also be applied in ozone and in the peracetic acid bleaching stage. The sensors can be utilized as tools during process monitoring or diagnostics. With the aid of monitoring it is possible to clarify how the different process operation models affect the corrosion of materials. (author)

  13. Yield-increasing additives in kraft pulping: Effect on carbohydrate retention, composition and handsheet properties

    Energy Technology Data Exchange (ETDEWEB)

    Vaaler, David Andre Grimsoeen

    2008-07-01

    In this thesis, increased hemicellulose retention during kraft pulping has been studied. The work has been divided into three parts: i) Development of an accessible and reliable method for determination of carbohydrate composition of kraft pulps ii) Investigation of the composition and molecular mass distributions of the carbohydrates in kraft pulps with increased hemicellulose content iii) Investigation of the effect of increased hemicellulose content on the sheet properties of kraft pulps with increased hemicellulose content. A method for carbohydrate determination was developed. In this method, enzymes are used to hydrolyse the pulp into monosaccharides. A relatively mild acid hydrolysis is performed prior to detection on an HPLC with an RI-detector. The pulp is not derivatized and no pre-treatment (mechanical or chemical) is needed to determine the carbohydrate composition using the method developed here. Peak deconvolution software is used to improve the accuracy. Polysulphide and H2S primarily increase the glucomannan yield, which can be boosted by up to 7 % on o.d. wood. However, the cellulose yield is more affected by the cooking time and the maximum yield increase of cellulose is approximately 2 % on o.d. wood compared to an ordinary kraft pulp. The cooking time is influenced by sulphide ion concentration, AQ addition and the final Kappa number. The xylan yield is remarkably stable, however the alkali profile during the cook may influence the xylan yield. Surface xylan content of the fibres depends on residual alkali concentration in the black liquor. The molecular mass distributions of cellulose and hemicellulose were determined for pulps with increased hemicellulose content using size exclusion chromatography. Deconvolution by peak separation software is used to gain information about the degree of polymerization for cellulose and hemicellulose. The average DP of glucomannan in the kraft fibre was found to be 350 +- 30 and the average DP of xylan in the

  14. Phenol oxidation with hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Ramiez Cortina, R.C.; Hernadez Perez, I. [Univ. Autonoma Metropolitana - Azcapotzalco, Div. de CBI, Dept. de Energia, Azcapotzalco (Mexico); Ortiz Lozoya, C.E. [Univ. Autonoma Metropolitana - Azcapotzalco, Div. de CBI, Dept. de Energia, Azcapotzalco (Mexico)]|[Inst. Mexicano del Petroleo (Mexico); Alonso Gutierrez, M.S. [Inst. National Polytechnique, ENSCT, Lab. of Chimie Agro-Industrielle, Toulouse (France)

    2003-07-01

    In this work the process application of advanced oxidation is investigated with hydrogen peroxide, for the phenol destruction. The experiments were carried out in a glass reactor of 750 mL. Three phenol concentrations were studied (2000, 1000 and 500 ppm) being oxidized with H{sub 2}O{sub 2} (1, 2 and 3 M). The tests of oxidation had a reaction time of 48 h at ambient temperature and pressure. The phenol degradation was determined as COD at different reaction times and intermediate oxidation products were analyzed by chromatography. The results of this study show that it is possible to degrade phenol (1000 ppm) until 90% with H{sub 2}O{sub 2} 2M. Being achieved the best efficiency with a good molar relationship of H{sub 2}O{sub 2}/phenol. Intends a reaction outline in the degradation of the phenol. (orig.)

  15. 7 CFR 58.431 - Hydrogen peroxide.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Hydrogen peroxide. 58.431 Section 58.431 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.431 Hydrogen peroxide. The solution shall comply with the specification of the U.S...

  16. Problem of the lithium peroxide thermal stability

    International Nuclear Information System (INIS)

    Nefedov, R A; Ferapontov, Yu A; Kozlova, N P

    2016-01-01

    The behavior of lithium peroxide and lithium peroxide monohydrate samples under heating in atmospheric air was studied by the method of thermogravimetric analysis (TGA) and differential thermal analysis (DTA). It was found that in the temperature range of 32°C to 82°C the interaction of lithium peroxides and steam with the formation of lithium peroxide monohydrate occurs, which was confirmed chemically and by X-ray Single-qualitative analysis. It was experimentally found that lithium peroxide starts to decompose into the lithium oxide and oxygen in the temperature range of 340 ÷ 348°C. It was established that the resulting thermal decomposition of lithium oxide, lithium peroxide at the temperature of 422°C melts with lithium carbonate eutecticly. The manifestation of polymorphism was not marked(seen or noticed) under the heating of studied samples of lithium peroxide and lithium peroxide monohydrate in the temperature range of 25°C ÷ 34°C. (paper)

  17. Photo-oxidation of histidine peptides yields high concentrations of unstable peroxides

    International Nuclear Information System (INIS)

    Policarpio, V.V.; Hawkins, C.L.; Davies, M.J.

    2003-01-01

    Oxidation of proteins by UV, and visible light in the presence of sensitizers, results in side chain modification as well as aggregation and fragmentation. In particular, singlet oxygen has been reported to oxidize Met, Trp, Tyr, Cys and His side chains in a selective manner. In this study the oxidation of histidine and its derivatives, and His-containing peptides is examined using a range of sensitizers, to determine whether peroxides are major intermediates, and the mechanism of formation of these species. Visible light-sensitised oxidation of Gly-His-Gly in the presence of oxygen and rose bengal gives unstable substrate-derived peroxides with the peroxide yield increasing with increasing photolysis time. Similar behaviour was detected with other photosensitizers, though the peroxide yields varied with the sensitizer at identical concentrations with rose bengal > aluminium phthalocyanine > hematoporphyrin IX > zinc phthalocyanine > tetrakisporphine. The peroxide yield was decreased in the presence of azide and enhanced when deuterium oxide was employed as the solvent, consistent with peroxide formation being singlet oxygen mediated. Experiments using anoxic conditions gave low yields of peroxides confirming the oxygen-dependence of these reactions. HPLC analysis showed rapid loss of the parent peptide, with subsequent formation of both stable and unstable products; these are currently being characterized by MS and NMR. Similar behavior has been observed with other His derivatives. The yield of singlet oxygen formed in these reactions has been estimated using a bleaching assay (N, N-dimethyl-4-nitrosoaniline). Quantification of singlet oxygen formation and Gly-His-Gly derived peroxide during rose bengal-mediated photooxidation indicated a conversion efficiency of the initial singlet oxygen into substrate-derived peroxides of ca. 75% indicating that peroxide formation is a highly efficient and major reaction pathway

  18. Induced resistance to hydrogen peroxide, UV and gamma radiation in bacillus species

    International Nuclear Information System (INIS)

    Bashandy, A.S.

    2005-01-01

    The catalase activity produced in four bacillus spp.(bacillus cereus, B. laterosporus, B. pumilus and B. subtilis (Escherichia coli was used for comparison) was measured and the sensitivity of these bacteria to hydrogen peroxide was tested. Bacillus spp. had higher resistance to hydrogen peroxide than E. coil. cultures of bacillus spp . When pretreated with sublethal level of hydrogen peroxide, became relatively resistant to the lethal effects of hydrogen than untreated control cultures. These pretreated cells were also resistant to lethality mediated by UV light and gamma radiation. The obtained results suggest that bacillus spp. Possess inducible defense mechanism (s) against the deleterious effects of oxidants and /or ionizing radiation

  19. Viscoelastic Properties of Dental Pulp Tissue and Ramifications on Biomaterial Development for Pulp Regeneration.

    Science.gov (United States)

    Erisken, Cevat; Kalyon, Dilhan M; Zhou, Jian; Kim, Sahng G; Mao, Jeremy J

    2015-10-01

    A critical step in biomaterial selection effort is the determination of material as well as the biological properties of the target tissue. Previously, the selection of biomaterials and carriers for dental pulp regeneration has been solely based on empirical experience. In this study, first, the linear viscoelastic material functions and compressive properties of miniature pig dental pulp were characterized using small-amplitude oscillatory shear and uniaxial compression at a constant rate. They were then compared with the properties of hydrogels (ie, agarose, alginate, and collagen) that are widely used in tissue regeneration. The comparisons of the linear viscoelastic material functions of the native pulp tissue with those of the 3 hydrogels revealed the gel-like behavior of the pulp tissue over a relatively large range of time scales (ie, over the frequency range of 0.1-100 rps). At the constant gelation agent concentration of 2%, the dynamic properties (ie, storage and loss moduli and the tanδ) of the collagen-based gel approached those of the native tissue. Under uniaxial compression, the peak normal stresses and compressive moduli of the agarose gel were similar to those of the native tissue, whereas alginate and collagen exhibited significantly lower compressive properties. The linear viscoelastic and uniaxial compressive properties of the dental pulp tissue reported here should enable the more appropriate selection of biogels for dental pulp regeneration via the better tailoring of gelation agents and their concentrations to better mimic the dynamic and compressive properties of native pulp tissue. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  20. Immunolocalization of bone-resorptive cytokines in rat pulp and periapical lesions following surgical pulp exposure.

    Science.gov (United States)

    Tani-Ishii, N; Wang, C Y; Stashenko, P

    1995-08-01

    The bone-resorptive cytokines interleukin 1 (IL-1) and tumor necrosis factor (TNF) have been implicated in the pathogenesis of many chronic inflammatory diseases, including pulpitis and apical periodontitis.To further elucidate their role in these disorders, we have identified cells that express IL-1 alpha and TNF alpha in infected pulps and in developing rat periapical lesions after surgical pulp exposure. As detected by immunohistochemistry, IL-1 alpha- and TNF alpha-positive cells were present as early as 2 days after pulp exposure in both the pulp and periapical region. The numbers of cytokine-expressing cells increased up to day 4 in the pulp and up to day 30 in the periapex. In contrast, cells expressing IL-1 beta and TNF beta, the homologous forms of these mediators, were not found in pulp or periapical lesions during this period. Cells expressing IL-1 alpha and TNF alpha were identified primarily as macrophages and fibroblasts, with occasional staining of polymorphonuclear leukocytes. Osteoblasts and osteoclasts were also positive, whereas lymphocytes were negative. In general, cytokine-expressing cells were located proximal to abscesses and the root apex. These findings demonstrate that cells that express bone-resorptive cytokines IL-1 alpha and TNF alpha are present immediately after pulp exposure in this model, which supports the hypothesis that these mediators play a key role in pulpal and periapical pathogenesis, including the concomitant bone destruction. They also indicate that both resident connective tissue cells as well as infiltrating cells express bone-resorptive cytokines in response to infection in these lesions.

  1. Hydrogen peroxide treatment of TCE contaminated soil

    International Nuclear Information System (INIS)

    Hurst, D.H.; Robinson, K.G.; Siegrist, R.L.

    1993-01-01

    Solvent contaminated soils are ubiquitous in the industrial world and represent a significant environmental hazard due to their persistence and potentially negative impacts on human health and the environment. Environmental regulations favor treatment of soils with options which reduce the volume and toxicity of contaminants in place. One such treatment option is the in-situ application of hydrogen peroxide to soils contaminated with chlorinated solvents such as trichloroethylene (TCE). This study investigated hydrogen peroxide mass loading rates on removal of TCE from soils of varying organic matter content. Batch experiments conducted on contaminated loam samples using GC headspace analysis showed up to 80% TCE removal upon peroxide treatment. Column experiments conducted on sandy loam soils with high organic matter content showed only 25% TCE removal, even at hydrogen peroxide additions of 25 g peroxide per kg soil

  2. Rearrangements of organic peroxides and related processes

    Directory of Open Access Journals (Sweden)

    Ivan A. Yaremenko

    2016-08-01

    Full Text Available This review is the first to collate and summarize main data on named and unnamed rearrangement reactions of peroxides. It should be noted, that in the chemistry of peroxides two types of processes are considered under the term rearrangements. These are conventional rearrangements occurring with the retention of the molecular weight and transformations of one of the peroxide moieties after O–O-bond cleavage. Detailed information about the Baeyer−Villiger, Criegee, Hock, Kornblum−DeLaMare, Dakin, Elbs, Schenck, Smith, Wieland, and Story reactions is given. Unnamed rearrangements of organic peroxides and related processes are also analyzed. The rearrangements and related processes of important natural and synthetic peroxides are discussed separately.

  3. Evaluation of bleachability on pine and eucalyptus kraft pulps

    Directory of Open Access Journals (Sweden)

    Marcela Freitas Andrade

    2013-09-01

    Full Text Available In recent decades, the pulp industry has been changing and improving its manufacturing processes in order to enhance production capacity, product quality and environmental performance. The aim of this study was to evaluate the bleachability effect on the efficient washing and alkaline leaching in eucalyptus and pine Kraft pulps using three different bleaching sequences: AD(EPD, A/D(EPDP and DHT(EPDP. This study was carried out in two stages. In the first part, the optimum conditions for pulp bleaching in order to achieve a brightness of 90% ISO were established. The second step was a comparative study between the pulps that received alkaline leaching and efficient washing with reference pulp (without treatment. The brightness, viscosity, kappa number and HexA in pulp were analyzed. The three sequences studied reached the desired brightness, but the sequence AD(EPD produced a lower reagent consumption for the same brightness. In the three sequences studied, the efficient washing of the pulp after oxygen delignification has contributed significantly to the removal of dissolved organic and inorganic materials in the pulp and the alkaline leaching decreased significantly the pulp kappa number due to a higher pulp delignification and bleachability.

  4. Expression of high mobility group box 1 in inflamed dental pulp and its chemotactic effect on dental pulp cells

    International Nuclear Information System (INIS)

    Zhang, Xufang; Jiang, Hongwei; Gong, Qimei; Fan, Chen; Huang, Yihua; Ling, Junqi

    2014-01-01

    Highlights: • HMGB1 translocated from nucleus to cytoplasm during dental pulp inflammation. • HMGB1and its receptor RAGE were up-regulated in hDPCs under LPS stimulation. • HMGB1 enhanced hDPCs migration and induces cytoskeleton reorganization. • HMGB1 may play a critical role in dental pulp repair during inflamed state. - Abstract: High mobility group box 1 protein (HMGB1) is a chromatin protein which can be released extracellularly, eliciting a pro-inflammatory response and promoting tissue repair process. This study aimed to examine the expression and distribution of HMGB1 and its receptor RAGE in inflamed dental pulp tissues, and to assess its effects on proliferation, migration and cytoskeleton of cultured human dental pulp cells (DPCs). Our data demonstrated that cytoplasmic expression of HMGB1 was observed in inflamed pulp tissues, while HMGB1 expression was confined in the nuclei in healthy dental pulp. The mRNA expression of HMGB1 and RAGE were significantly increased in inflamed pulps. In in vitro cultured DPCs, expression of HMGB1 in both protein and mRNA level was up-regulated after treated with lipopolysaccharide (LPS). Exogenous HMGB1 enhanced DPCs migration in a dose-dependent manner and induced the reorganization of f-actin in DPCs. Our results suggests that HMGB1 are not only involved in the process of dental pulp inflammation, but also play an important role in the recruitment of dental pulp stem cells, promoting pulp repair and regeneration

  5. Expression of high mobility group box 1 in inflamed dental pulp and its chemotactic effect on dental pulp cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xufang, E-mail: xufang.zhang@student.qut.edu.au [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Institute of Health and Biomedical Innovation, Queensland University of Technology, Brisbane, QLD 4059 (Australia); Jiang, Hongwei, E-mail: jianghw@163.com [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Gong, Qimei, E-mail: gongqmei@gmail.com [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Fan, Chen, E-mail: c3.fan@student.qut.edu.au [Institute of Health and Biomedical Innovation, Queensland University of Technology, Brisbane, QLD 4059 (Australia); Huang, Yihua, E-mail: enu0701@163.com [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Ling, Junqi, E-mail: lingjq@mail.sysu.edu.cn [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China)

    2014-08-08

    Highlights: • HMGB1 translocated from nucleus to cytoplasm during dental pulp inflammation. • HMGB1and its receptor RAGE were up-regulated in hDPCs under LPS stimulation. • HMGB1 enhanced hDPCs migration and induces cytoskeleton reorganization. • HMGB1 may play a critical role in dental pulp repair during inflamed state. - Abstract: High mobility group box 1 protein (HMGB1) is a chromatin protein which can be released extracellularly, eliciting a pro-inflammatory response and promoting tissue repair process. This study aimed to examine the expression and distribution of HMGB1 and its receptor RAGE in inflamed dental pulp tissues, and to assess its effects on proliferation, migration and cytoskeleton of cultured human dental pulp cells (DPCs). Our data demonstrated that cytoplasmic expression of HMGB1 was observed in inflamed pulp tissues, while HMGB1 expression was confined in the nuclei in healthy dental pulp. The mRNA expression of HMGB1 and RAGE were significantly increased in inflamed pulps. In in vitro cultured DPCs, expression of HMGB1 in both protein and mRNA level was up-regulated after treated with lipopolysaccharide (LPS). Exogenous HMGB1 enhanced DPCs migration in a dose-dependent manner and induced the reorganization of f-actin in DPCs. Our results suggests that HMGB1 are not only involved in the process of dental pulp inflammation, but also play an important role in the recruitment of dental pulp stem cells, promoting pulp repair and regeneration.

  6. Activated carbon prepared from coffee pulp: potential adsorbent of organic contaminants in aqueous solution.

    Science.gov (United States)

    Gonçalves, Maraisa; Guerreiro, Mário César; Ramos, Paulize Honorato; de Oliveira, Luiz Carlos Alves; Sapag, Karim

    2013-01-01

    The processing of coffee beans generates large amounts of solid and liquid residues. The solid residues (pulp, husk and parchment) represent a serious environmental problem and do not have an adequate disposal mechanism. In this work, activated carbons (ACs) for adsorption of organic compounds were prepared from coffee pulp by controlled temperature at different pulp/Na2HPO4 ratios (4:1, 2:1, 5:4 and 1:1). The N2 adsorption/desorption isotherms showed ACs with high quantities of mesopores and micropores and specific surface areas of 140, 150, 450 and 440 m(2)g(-1) for AC 4:1, AC 2:1, AC 5:4 and AC 1:1, respectively. The prepared material AC 5:4 showed a higher removal capacity of the organic contaminants methylene blue (MB), direct red (DR) and phenol than did a Merck AC. The maximum capacities for this AC are approximately 150, 120 and 120 mg g(-1) for MB, DR and phenol, respectively. Thus, a good adsorbent was obtained from coffee pulp, an abundant Brazilian residue.

  7. A practical approach towards energy conversion through bio-refining of mixed kraft pulps

    Energy Technology Data Exchange (ETDEWEB)

    Dharm, D.; Upadhyaya, J.S.; Tyagi, C.H.; Ahamad, S. (Dept. of Paper Technology, Indian Inst. of Technology Roorkee, Saharanpur (India))

    2007-07-01

    The pulp and paper industry is an energy intensive process industry where energy contributes about 16-20% of the manufacturing cost. Due to shortage in energy availability and increase in energy cost, energy conservation has become a necessity in the paper industry. A laboratory study on bleached and unbleached kraft pulps having 15% bamboo, eucalyptus 15%, poplar waste 20% and veneer waste 50% was conducted using two distinct commercial enzymes i.e. cellulases and xylanase and its effect on slowness, drainage time, beating time, mechanical strength properties and power consumption were studied. Enzymatic pretreatment of chemical pulp in laboratory improves degSR by 5 and 4 points in case of bleached and unbleached pulps respectively at the same beating time. Breaking length improves up to 4.0% at the constant beating level. The application of cellulase during refining saves energy 18.5% at constant refining level i.e. 28 degSR. The enzymatic treatment shows a power saving per 100 metric tone of paper by 1390 kWh which costs power saving in euro 160.70/ 100 metric tone of paper. In this way, net cost saving by deducting the cost of enzyme per 100 metric tone of paper is euro 157.90. (orig.)

  8. Stage-specific effects of FGF2 on the differentiation of dental pulp cells

    Science.gov (United States)

    Sagomonyants, Karen; Mina, Mina

    2015-01-01

    Dentinogenesis is a complex and multistep process, which is regulated by various growth factors, including members of the Fibroblast Growth Factor (FGF) family. Both positive and negative effects of FGFs on dentinogenesis have been reported but the underlying mechanisms of these conflicting results are still unclear. To gain better insight into the role of FGF2 in dentinogenesis, we used dental pulp cells from various transgenic mice, in which fluorescent protein expression identifies cells at different stages of odontoblast differentiation. Our results showed that continuous exposure of pulp cells to FGF2 inhibited mineralization and revealed both stimulatory and inhibitory effects of FGF2 on expression of markers of dentinogenesis and various transgenes. During the proliferation phase of in vitro growth FGF2 increased expression of markers of dentinogenesis and the percentages of DMP1-GFP+ functional odontoblasts and DSPP-Cerulean+ odontoblasts. Additional exposure to FGF2 during the differentiation/mineralization phase of in vitro growth decreased the extent of mineralization, expression of markers of dentinogenesis, and expression of DMP1-GFP and DSPP-Cerulean transgenes. Recovery experiments showed that the inhibitory effects of FGF2 on dentinogenesis were related to the blocking of differentiation of cells into mature odontoblasts. These observations together showed stage-specific effects of FGF2 on dentinogenesis by dental pulp cells and provide critical information for the development of improved treatments for vital pulp therapy and dentin regeneration. PMID:25823776

  9. Papermaking Properties of Carpinus betulus with kraft, Soda and Soda-Urea Pulping Processes

    Directory of Open Access Journals (Sweden)

    Rasoul Darstan

    2013-06-01

    Full Text Available This research was carried out in order to comparatively investigate the hornbeam kraft, soda and soda-urea papermaking properties. The selected treatment in kraft process had an average yield of 44.43% and kappa number of 23.75. In soda process the selected treatment had an average yield of 38.75% and kappa number of 19.28. In soda-urea process, the selected treatments had an average yield of 39.85, 40.1, 40.5, 39.8 and 40.61 and kappa number of 21.21, 22.33, 22.66, 25.28 and 26.85. After refining the selected pulp to reach the freeness of 400±25 ml CSF, 60 g/m2 handsheets were made and physical, mechanical and optical properties were measured. Results showed that kraft pulps had higher yield and better refinability than soda and soda-urea pulps. Papers made from kraft process had higher strength properties than those made of soda and soda-urea process. With addition of urea, yield and kappa number of pulps increased. The highest improvement in tensile index, breaking length and tear index was achieved with addition of 3% urea and the highest improvement in burst index was achieved with adding 4% urea. Results of brightness measurements showed that papers from kraft and soda processes had the lowest and highest brightness degree respectively. With the addition of urea, brightness of papers decreased.

  10. [Temporal and spacial expression of perlecan in dental pulp after injury].

    Science.gov (United States)

    Li, Qiao; Sun, Hong; Pan, Yi-huai; Liu, Chuan-tong

    2014-02-01

    To investigate the temporal and special expressions and functions of perlecan in dental pulp of rats after injury. Specimens of one side of maxillary molars of 24 male SD rats were collected 1,3,5,7 days after injury, and the other side were used as controls. The specimens were decalcified and embedded in paraffin, sliced by longitudinal section and stained by immunohistochemistry. The staining of perlecan and β1 integrin were examined, and the average optical density (AOD) was compared. The measurement data were analyzed by ANOVA using SPSS 19.0 software package. The staining intensity of perlecan in dental pulp in the experimental group was significantly higher compared with that of the control group. The immunolocalization of perlecan in dental pulp was gradually progressed as the inflamed tissue was progressing after injury, and its AOD was significantly higher than that of control group (F=11.104,P>0.05), especially in the group of 1 d. The staining of β1 integrin was generally enhanced in the pulp 3 d after injury, and its AOD was significantly higher than that of control group (F=124.18,P>0.05). Perlecan may play an important role in tissue defense mechanism after injury through regulating angiogenesis and inflammatory cell infiltration. Supported by Science and Technology Research Project of Department of Education of Zhejiang Province (20051196) and Wenzhou City (Y20100015).

  11. Oil quality of passion fruit seeds subjected to a pulp-waste purification process

    Directory of Open Access Journals (Sweden)

    Suelen Alvarenga Regis

    2015-06-01

    Full Text Available Passion fruit seeds must be clean and dry before the extraction processing to obtain high-quality oil for edible and cosmetic purposes. This research studies the viability of a cleaning process of seeds by evaluating the oil quality. The research examined 2 maturation stages of the fruit and one purification process of the seeds, compared to the control. The oil quality was evaluated by fatty acid composition, acidity, peroxide value and oxidative stability. The pulp waste suffered a thermal treatment in an alkaline water solution at 60°C for 10min and was further purified in an experimental decanter. In the control treatment, the pulp waste was processed using only water at ambient conditions. The passion fruit seeds were totally cleaned by the thermal/chemical treatment, allowing a faster drying (less than 50% of the drying time of the seeds and a bit higher yield of oil extraction (proportionally around 7.7%, without changes in quality of the oil

  12. Pembuatan Pulp dari Alang-alang

    OpenAIRE

    Ivan Wibisono Aylianawati

    2011-01-01

    Alang-alang merupakan tanaman gulma yang jumlahnya cukup besar di Indonesia. Hingga saat ini pemanfaatan dalam jumlah yang besar terhadap alang-alang di Indonesia belum ada. Alang-alang mempunyai kandungan selulosa yang cukup tinggi. Pada penelitian pendahuluan terhadap bahan baku alang-alang mengandung kadar alfa selulosa sekitar 41,7% dan mempunyai bilangan Kappa sebesar 37,1886. Maka alang-alang bisa dijadikan sebagai bahan dari pulp untuk pembuatan kertas. Tujuan penelitian ini adalah ...

  13. Potential for biohydrogen and methane production from olive pulp

    DEFF Research Database (Denmark)

    Gavala, Hariklia N.; Skiadas, Ioannis V.; Ahring, Birgitte Kiær

    2005-01-01

    The present study investigates the potential for thermophilic biohydrogen and methane production from olive pulp, which is the semi-solid residue coming from the two-phase processing of olives. It focussed on: a) production of methane from the raw olive pulp, b) anaerobic bio-production of hydrogen...... from the olive pulp, and c) subsequent anaerobic treatment of the hydrogen-effluent with the simultaneous production of methane. Both continuous and batch experiments were performed. The hydrogen potential of the olive pulp amounted to 1.6 mmole H-2 per g TS. The methane potential of the raw olive pulp...... and hydrogen-effluent was as high as 19 mmole CH4 per g TS. This suggests that olive pulp is an ideal substrate for methane production and it shows that biohydrogen production can be very efficiently coupled with a subsequent step for methane production....

  14. Mechanical deconstruction of lignocellulose cell walls and their enzymatic saccharification

    Science.gov (United States)

    Ingrid C. Hoeger; Sandeep S. Nair; Arthur J. Ragauskas; Yulin Deng; Orlando J. Rojas; J.Y. Zhu

    2013-01-01

    Laboratory mechanical softwood pulps (MSP) and commercial bleached softwood kraft pulps (BSKP) were mechanically fibrillated by stone grinding with a SuperMassColloider®. The extent of fibrillation was evaluated by SEM imaging, water retention value (WRV) and cellulase adsorption. Both lignin content and mechanical treatment significantly affected deconstruction and...

  15. Polyphenols profile and antioxidant activity of skin and pulp of a rare apple from Marche region (Italy).

    Science.gov (United States)

    Giomaro, Giovanna; Karioti, Anastasia; Bilia, Anna Rita; Bucchini, Anahi; Giamperi, Laura; Ricci, Donata; Fraternale, Daniele

    2014-01-01

    Apples are an important source of polyphenols in the human diet and the consumption of this fruit has been linked to the prevention of degenerative diseases. CATECHINS, PROCYANIDINS, HYDROXYCINNAMIC ACIDS, FLAVONOL GLYCOSIDES, DIHYDROCHALCONE GLYCOSIDES AND ONE ANTHOCYANIN: cyanidin-3-O-galactoside, were identified both in the peel and pulp. Procyanidins, catechins and flavonols represent the main constituents of peel. Concerning the antioxidant activity, in the reduction of the stable DPPH radical and in the inhibition of lipid peroxidation, the ethanolic extracts of red peel and red pulp showed a good similar activity comparable to ascorbic acid in the DPPH test and about ten times more active than BHT in the lipoxygenase test, and were much more active than aqueous extracts. The ORAC value of red pulp aqueous extract resulted comparable to that of red berries: vaccinium, rubus and ribes, foods appreciated for their health value. This apple contains an appreciable amount of polyphenols also in the flesh; this variety with red flesh can also be useful for researchers engaged in apples varietal innovation in addition to being used as food apple.

  16. Assay to detect lipid peroxidation upon exposure to nanoparticles.

    Science.gov (United States)

    Potter, Timothy M; Neun, Barry W; Stern, Stephan T

    2011-01-01

    This chapter describes a method for the analysis of human hepatocarcinoma cells (HEP G2) for lipid peroxidation products, such as malondialdehyde (MDA), following treatment with nanoparticle formulations. Oxidative stress has been identified as a likely mechanism of nanoparticle toxicity, and cell-based in vitro systems for evaluation of nanoparticle-induced oxidative stress are widely considered to be an important component of biocompatibility screens. The products of lipid peroxidation, lipid hydroperoxides, and aldehydes, such as MDA, can be measured via a thiobarbituric acid reactive substances (TBARS) assay. In this assay, which can be performed in cell culture or in cell lysate, MDA combines with thiobarbituric acid (TBA) to form a fluorescent adduct that can be detected at an excitation wavelength of 530 nm and an emission wavelength of 550 nm. The results are then expressed as MDA equivalents, normalized to total cellular protein (determined by Bradford assay).

  17. Study on the agglomeration kinetics of uranium peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Bertrand, M.; Mojica Rodriguez, L.A. [CEA, Centre de Marcoule, Nuclear Energy Division, RadioChemistry and Process Department, 17171, Bagnols-sur-Ceze 30207 (France); Muhr, H.; Plasari, E. [Reaction and Process Engineering Laboratory, CNRS, University of Lorraine. 1 rue Grandville, BP 20451, Nancy 54001 (France); Auger, F. [Areva Mines/SEPA. 2 route de Lavaugrasse, Bessines-sur-Gartempe 87250 (France)

    2016-07-01

    Considering the previous study dealing with thermodynamic and kinetic phenomena (nucleation and crystal growth) during the uranium peroxide precipitation, this work focuses on the agglomeration mechanism. It provides the results obtained from the experiments carried out in a mixed suspension - mixed product removal (MSMPR) mixer operating at steady state. The influence of the operating parameters on the uranium peroxide agglomerates was studied in order to identify the agglomeration kernel. The method is based on the resolution of the population balance equation using the method of moments and the experimental particle size distributions. The results lead to a size-independent kernel directly proportional to the crystal growth rate. Under the stirring conditions studied, the agglomeration appears to be significantly reduced by mixing which results in a kernel inversely proportional to the average shear rate. The agglomeration kinetic law obtained in this study will be used for the process modelling in a further study. (authors)

  18. Study on the agglomeration kinetics of uranium peroxide

    International Nuclear Information System (INIS)

    Bertrand, M.; Mojica Rodriguez, L.A.; Muhr, H.; Plasari, E.; Auger, F.

    2016-01-01

    Considering the previous study dealing with thermodynamic and kinetic phenomena (nucleation and crystal growth) during the uranium peroxide precipitation, this work focuses on the agglomeration mechanism. It provides the results obtained from the experiments carried out in a mixed suspension - mixed product removal (MSMPR) mixer operating at steady state. The influence of the operating parameters on the uranium peroxide agglomerates was studied in order to identify the agglomeration kernel. The method is based on the resolution of the population balance equation using the method of moments and the experimental particle size distributions. The results lead to a size-independent kernel directly proportional to the crystal growth rate. Under the stirring conditions studied, the agglomeration appears to be significantly reduced by mixing which results in a kernel inversely proportional to the average shear rate. The agglomeration kinetic law obtained in this study will be used for the process modelling in a further study. (authors)

  19. Association between dental pulp stones and calcifying nanoparticles.

    Science.gov (United States)

    Zeng, Jinfeng; Yang, Fang; Zhang, Wei; Gong, Qimei; Du, Yu; Ling, Junqi

    2011-01-07

    The etiology of dental pulp stones, one type of extraskeletal calcification disease, remains elusive to date. Calcifying nanoparticles (CNPs), formerly referred to as nanobacteria, were reported to be one etiological factor in a number of extraskeletal calcification diseases. We hypothesized that CNPs are involved in the calcification of the dental pulp tissue, and therefore investigated the link between CNPs and dental pulp stones. Sixty-five freshly collected dental pulp stones, each from a different patient, were analyzed. Thirteen of the pulp stones were examined for the existence of CNPs in situ by immunohistochemical staining (IHS), indirect immunofluorescence staining (IIFS), and transmission electron microscope (TEM). The remaining 52 pulp stones were used for isolation and cultivation of CNPs; the cultured CNPs were identified and confirmed via their shape and growth characteristics. Among the dental pulp stones examined in situ, 84.6% of the tissue samples staines positive for CNPs antigen by IHS; the corresponding rate by IIFS was 92.3 %. In 88.2% of the cultured samples, CNPs were isolated and cultivated successfully. The CNPs were visible under TEM as 200-400 nm diameter spherical particles surrounded by a compact crust. CNPs could be detected and isolated from a high percentage of dental pulp stones, suggesting that CNPs might play an important role in the calcification of dental pulp.

  20. The caries process and its effect on the pulp

    DEFF Research Database (Denmark)

    Bjørndal, Lars

    2008-01-01

    The understanding of the caries process and its effect on the pulp is presented in the context that caries does develop in various rates of progression. Early in the caries process, the pulp reflects changes within lesion activity. Thus, the early pulp response is reversible. Later, the rate...... of caries progression is reflected by the quality of the tertiary dentin. Slowly progressing lesions create tertiary dentin resembling normal tubular dentin. Rapidly progressing lesions lead to the production of a tubular dentin or complete absence of tertiary dentin, as well as pulp necrosis and apical...

  1. A modified efficient method for dental pulp stem cell isolation.

    Science.gov (United States)

    Raoof, Maryam; Yaghoobi, Mohammad Mehdi; Derakhshani, Ali; Kamal-Abadi, Ali Mohammadi; Ebrahimi, Behnam; Abbasnejad, Mehdi; Shokouhinejad, Noushin

    2014-03-01

    Dental pulp stem cells can be used in regenerative endodontic therapy. The aim of this study was to introduce an efficient method for dental pulp stem cells isolation. In this in-vitro study, 60 extracted human third molars were split and pulp tissue was extracted. Dental pulp stem cells were isolated by the following three different methods: (1) digestion of pulp by collagenase/dispase enzyme and culture of the released cells; (2) outgrowth of the cells by culture of undigested pulp pieces; (3) digestion of pulp tissue pieces and fixing them. The cells were cultured in minimum essential medium alpha modification (αMEM) medium supplemented with 20% fetal bovine serum(FBS) in humid 37°C incubator with 5% CO 2. The markers of stem cells were studied by reverse transcriptase polymerase chain reaction (PCR). The student t-test was used for comparing the means of independent groups. P third method, we obtained stem cells successfully with about 60% efficiency after 2 days. The results of RT-PCR suggested the expression of Nanog, Oct-4, and Nucleostemin markers in the isolated cells from dental pulps. This study proposes a new method with high efficacy to obtain dental pulp stem cells in a short time.

  2. Method of increasing efficiency of uranium sorption from acid pulp

    International Nuclear Information System (INIS)

    Parobek, P.; Hinterholzinger, O.; Baloun, S.; Homolka, V.; Vanek, J.; Vebr, Z.

    1989-01-01

    Acid pulp containing uranium is adjusted to pH 2.5 to 4 with alkaline agents, such as alkaline pulp, lime milk, finely ground limestone or soda, or a combination thereof. The treated pulp is put into contact with an ion exchanger whose pH has been adjuste to a range of 2.5 to 4. Partial pulp neutralization causes the hydrolysis of the iron present and an overall reduction in salt contents and a significant increase in the ion exchanger sorptio capacity and thus the overall sorption efficiency. The quality o the eluate and of the uranium concentrate improves. (B.S.)

  3. Kinetic modeling of formic acid pulping of bagasse.

    Science.gov (United States)

    Tu, Qiliang; Fu, Shiyu; Zhan, Huaiyu; Chai, Xinsheng; Lucia, Lucian A

    2008-05-14

    Organic solvent or organosolv pulping processes are alternatives to soda or kraft pulping to delignify lignocellulosic materials for the production of paper pulp. Formic acid, a typical organosolv system, has been presently examined under atmospheric pressure to pulp bagasse fibers. It was shown that efficient bagasse pulping was achieved when the formic acid concentration was limited to 90% (v/v). A statistical kinetic model based on the experimental results for the delignification of bagasse during formic acid pulping was developed that can be described as follows: D (delignification) = 0.747 x C(formicacid) (1.688) x (1 - e(-0.05171t)), an equation that can be used to predict the lignin content in formic acid during the pulping process. The delignification of bagasse by 90% formic acid was almost completed after approximately 80 min, while extended pulping did not improve the delignification but tended to degrade the carbohydrates in bagasse, especially the hemicelluloses, which were rapidly hydrolyzed at the onset of pulping.

  4. Functionalized scaffolds to control dental pulp stem cell fate

    Science.gov (United States)

    Piva, Evandro; Silva, Adriana F.; Nör, Jacques E.

    2014-01-01

    Emerging understanding about interactions between stem cells, scaffolds and morphogenic factors has accelerated translational research in the field of dental pulp tissue engineering. Dental pulp stem cells constitute a sub-population of cells endowed with self-renewal and multipotency. Dental pulp stem cells seeded in biodegradable scaffolds and exposed to dentin-derived morphogenic signals give rise to a pulp-like tissue capable of generating new dentin. Notably, dentin-derived proteins are sufficient to induce dental pulp stem cell differentiation into odontoblasts. Ongoing work is focused on developing ways of mobilizing dentin-derived proteins and disinfecting the root canal of necrotic teeth without compromising the morphogenic potential of these signaling molecules. On the other hand, dentin by itself does not appear to be capable of inducing endothelial differentiation of dental pulp stem cells, despite the well known presence of angiogenic factors in dentin. This is particularly relevant in the context of dental pulp tissue engineering in full root canals, where access to blood supply is limited to the apical foramina. To address this challenge, scientists are looking at ways to use the scaffold as a controlled release device for angiogenic factors. The aim of this manuscript is to present and discuss current strategies to functionalize injectable scaffolds and customize them for dental pulp tissue engineering. The long-term goal of this work is to develop stem cell-based therapies that enable the engineering of functional dental pulps capable of generating new tubular dentin in humans. PMID:24698691

  5. Final Technical Report Steam Cycle Washer for Unbleached Pulp

    Energy Technology Data Exchange (ETDEWEB)

    Starkey, Yvonne; Salminen, Reijo; Karlsnes, Andy

    2008-09-22

    Project Abstract for “Steam Cycle Washer for Unbleached Pulp” When completed, the patented SC Washer will provide an innovative, energy efficient demonstration project to wash unbleached pulp using a pressure vessel charged with steam. The Port Townsend Paper Corporation’s pulp mill in Port Townsend, WA was initially selected as the host site for conducting the demonstration of the SCW. Due to 2006 and 2007 delays in the project caused by issues with 21st Century Pulp & Paper, the developer of the SCW, and the 2007 bankruptcy proceedings and subsequent restructuring at Port Townsend Paper, the mill can no longer serve as a host site. An alternate host site is now being sought to complete the commercial demonstration of the Steam Cycle Washer for Unbleached Pulp. Additionally, estimated costs to complete the project have more than doubled since the initial estimates for the project were completed in 2002. Additional grant funding from DOE was sought and in July, 2008 the additional DOE funds were procured under a new DOE award, DE-PS36-08GO98014 issued to INL. Once the new host site is secured the completion of the project will begin under the management of INL. Future progress reports and milestone tracking will be completed under requirements of new DOE Award Number DE-PS36-08GO98014. The following are excerpts from the project Peer Review completed in 2006. They describe the project in some detail. Additional information can be found by reviewing DOE Award Number: DE-PS36-08GO98014. 5. Statement of Problem and Technical Barriers: The chemical pulping industry is one of the major users of fresh water in the United States. On average the industry uses over 80 tons of water to produce one ton of pulp, some states use up to 50% more (Washington 120 and Wisconsin 140). In order to process one ton of pulp using 80 tons of process water, a large amount of: • energy is used in process heat and • power is required for pumping the large volume of pulp slurries

  6. Hydrogen production from carrot pulp by the extreme thermophiles Caldicellulosiruptor saccharolyticus and Thermotoga neapolitana

    NARCIS (Netherlands)

    Vrije, de G.J.; Budde, M.A.W.; Lips, S.J.J.; Bakker, R.R.; Mars, A.E.; Claassen, P.A.M.

    2010-01-01

    Hydrogen was produced from carrot pulp hydrolysate, untreated carrot pulp and (mixtures of) glucose and fructose by the extreme thermophiles Caldicellulosiruptor saccharolyticus and Thermotoga neapolitana in pH-controlled bioreactors. Carrot pulp hydrolysate was obtained after enzymatic hydrolysis

  7. Observation of atmospheric peroxides during Wangdu Campaign 2014 at a rural site in the North China Plain

    Directory of Open Access Journals (Sweden)

    Y. Wang

    2016-09-01

    Full Text Available Measurements of atmospheric peroxides were made during Wangdu Campaign 2014 at Wangdu, a rural site in the North China Plain (NCP in summer 2014. The predominant peroxides were detected to be hydrogen peroxide (H2O2, methyl hydroperoxide (MHP and peroxyacetic acid (PAA. The observed H2O2 reached up to 11.3 ppbv, which was the highest value compared with previous observations in China at summer time. A box model simulation based on the Master Chemical Mechanism and constrained by the simultaneous observations of physical parameters and chemical species was performed to explore the chemical budget of atmospheric peroxides. Photochemical oxidation of alkenes was found to be the major secondary formation pathway of atmospheric peroxides, while contributions from alkanes and aromatics were of minor importance. The comparison of modeled and measured peroxide concentrations revealed an underestimation during biomass burning events and an overestimation on haze days, which were ascribed to the direct production of peroxides from biomass burning and the heterogeneous uptake of peroxides by aerosols, respectively. The strengths of the primary emissions from biomass burning were on the same order of the known secondary production rates of atmospheric peroxides during the biomass burning events. The heterogeneous process on aerosol particles was suggested to be the predominant sink for atmospheric peroxides. The atmospheric lifetime of peroxides on haze days in summer in the NCP was about 2–3 h, which is in good agreement with the laboratory studies. Further comprehensive investigations are necessary to better understand the impact of biomass burning and heterogeneous uptake on the concentration of peroxides in the atmosphere.

  8. Characterization of the oils from the pulp and seeds of avocado (cultivar: Fuerte fruits

    Directory of Open Access Journals (Sweden)

    Queiroz Paulo, Marçal

    2001-08-01

    Full Text Available Avocado (Persea americana Mill pulp and seeds of the cultivar Fuerte, cultivated in the Northeast region of Brazil, were analysed for their proximate composition. The lipid contents of the pulp and seeds were 15.39% and 1.87%, respectively. Hexane extracted oils from pulp and seeds presented similar refractive indices (1.4608 and 1.4592, specific gravity (0.9272 and 0.9300 and peroxide values (1.40 and 1.37, but different acid (2.45 and 4.12, iodine (77.6 and 69.4 and saponification values (178.3 and 231.6, respectively. Gas chromatographic analysis revealed the presence of twenty two and twenty seven fatty acids in pulp and seed oils, respectively. Palmitic acid was the principal saturated acid, present in concentrations of 21.3% in pulp and 20.8% in seed oils. The major difference between these oils was in their mono-unsaturated (C18:1 - 64.3%, for pulp and 15.4% in seed oil and poly-unsaturated (C18:2 and C18:3 - 9.14% and 0.46%, respectively, in pulp oil and 34.39% and 5.81%, respectively, in seed oil fatty acids composition.La semilla y pulpa del aguacate (Persea americana Mill, cultivar Fuerte, cultivado en la región del nordeste de Brasil fueron analizados para determinar su composición centesimal. El contenido de lípidos en pulpa y semillas, en la base húmeda fueron 15.39% y 1.87%, respectivamente. Los aceites extraídos de la pulpa y de las semillas por hexano representan similares índices de refracción (1.4608 y 1.4592, densidad específica (0.9272 y 0.9300 e índice de peróxidos (1.40 y 1.37 pero diferentes índices de acidez (2.45 y 4.12, iodo (77.6 y 69.4 y saponificación (178.3 y 231.6, respectivamente. El análisis de cromatografía gaseosa revela la presencia de 22 y 27 ácidos grasos en aceite de pulpa y de semillas, respectivamente. El ácido palmítico fue el principal ácido saturado, presente en concentraciones de 21,3% en pulpa y 20,8% en aceites de semillas. La principal diferencia entre estos aceites fue su

  9. EZH2 regulates dental pulp inflammation by direct effect on inflammatory factors.

    Science.gov (United States)

    Hui, Tianqian; A, Peng; Zhao, Yuan; Yang, Jing; Ye, Ling; Wang, Chenglin

    2018-01-01

    Pulpitis is a multi-factorial disease that could be caused by complex interactions between genetics, epigenetics and environmental factors. We aimed to evaluate the role of Enhancer of Zeste Homolog 2 (EZH2) in the inflammatory response of human dental pulp cells (HDPCs) and dental pulp tissues. The expressions of inflammatory cytokines in HDPCs treated by EZH2 complex or EZH2 siRNA with or without rhTNF-α were examined by quantitative real-time polymerase chain reaction (q-PCR). The levels of secreted inflammatory cytokines including IL-6, IL-8, IL-15, CCL2 and CXCL12 in culture supernatants were measured by Luminex assay. In rat pulpitis model, the effects of EZH2 on dental pulp tissues were verified by histology. We invested the mechanisms of the effect of EZH2 on the inflammatory factors by ChIP assay. EZH2 down-regulation inhibited the expression of inflammatory factors, including IL-6, IL-8, IL-15, CCL2 and CXCL12 in HDPCs. EZH2 complex promoted the expression and secretion of these inflammatory factors in HDPCs, while EZH2 silencing could attenuate the promotion of inflammatory factors that were induced by rhTNF-α. In pulpitis models of rats, EZH2 down-regulation inhibited the inflammatory process of dental pulp while EZH2 complex showed no significant facilitation of pulpal inflammation. In addition, EZH2 could bind on the promoters of IL-6, IL-8 and CCL2, but not IL-15 and CXCL12, to affect the transcription of these proinflammatory cytokines. In HDPCs, EZH2 could induce inflammation, while EZH2 down-regulation could attenuate the inflammatory responses. EZH2 plays an important role in this inflammatory process of dental pulp. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Comparison of Radicular Peroxide Leakage from four Commonly used Bleaching agents following Intracoronal Bleaching in Endodontically treated teeth - An In Vitro Study.

    Science.gov (United States)

    Madhu, Ks; Hegde, Swaroop; Mathew, Sylvia; Lata, DA; Bhandi, Shilpa H; N, Shruthi

    2013-08-01

    Non vital bleaching is simple, conservative procedure for esthetic correction of discolored endodontically treated teeth. The aim of this study was to determine and compare the amount of peroxide leakage from four different bleaching agents i.e superoxol, sodium perborate, combination of superoxol & sodium perborate and carbamide peroxide during intracoronal bleaching, as the safe and effective bleaching is the need of the hour. 50 extracted maxillary centrals were selected for the study. Following standardized protocol access, cleaning and shaping by step back technique and obturation was done using guttapercha and AH plus sealer. Access was sealed with Cavit G and outer root surface was coated with wax and nail varnish. The teeth were separated into crown and root and the root portion was placed in plastic tube containing distilled water for 7days.After incubation, 3mm of gutta-percha was removed below CEJ and 2mm glass ionomer cement base was placed. Grouped into five categories based on the bleaching agent placed in pulp chamber as -group1 (control)-distilled water, group 2-sodium perborate with distilled water , group 3- 30% hydrogen peroxide ,group 4-mixture of sodium perborate and 30% hydrogen peroxide and group 5-10% carbamide peroxide gel. Peroxide leakage was measured after 24hrs using ferrothiocyanate method and optical density using spectrophotometer. Statistical analysis of the data was conducted using ANOVA and multiple comparisons within the groups was done using BONFERRONI method (Post-Hoc tests). The results showed highest peroxide penetration from 30% hydrogen peroxide followed by mixture of sodium perborate with 30% hydrogen peroxide, mixture of sodium perborate with distilled water and least penetration from 10% carbamide peroxide gel. The results were statistically significant. Radicular peroxide leakage in 10% carbamide peroxide was significantly lower than the other tested bleaching agents making it a very safe alternative for intracoronal

  11. Potential of hot water extraction of birch wood to produce high-purity dissolving pulp after alkaline pulping.

    Science.gov (United States)

    Borrega, Marc; Tolonen, Lasse K; Bardot, Fanny; Testova, Lidia; Sixta, Herbert

    2013-05-01

    The potential of hot water extraction of birch wood to produce highly purified dissolving pulp in a subsequent soda-anthraquinone pulping process was evaluated. After intermediate extraction intensities, pulps with low xylan content (3-5%) and high cellulose yield were successfully produced. Increasing extraction intensity further decreased the xylan content in pulp. However, below a xylan content of 3%, the cellulose yield dramatically decreased. This is believed to be due to cleavage of glycosidic bonds in cellulose during severe hot water extractions, followed by peeling reactions during alkaline pulping. Addition of sodium borohydride as well as increased anthraquinone concentration in the pulping liquor increased the cellulose yield, but had no clear effects on pulp purity and viscosity. The low intrinsic viscosity of pulps produced after severe extraction intensities and soda-anthraquinone pulping corresponded to the viscosity at the leveling-off degree of polymerization, suggesting that nearly all amorphous cellulose had been degraded. Copyright © 2012 Elsevier Ltd. All rights reserved.

  12. Pemanfaatan Limbah Pulp Buah Semangka (Citrullus vulgaris, Schard) Untuk Pembuatan Nata De Watermelon Pulp Dengan Menggunakan Bakteri Acetobacter xylinum

    OpenAIRE

    Mawaddah

    2011-01-01

    This research done to know can or not the waste of watermelon pulp use to produce nata and how the effect of mass variation using to nata’s quality. This research was done with mass variation of watermelon pulp that is 10 g, 20 g, 30 g, 40 g, 50 g, 60 g, and watermelon pulp without adding sugar as control. Statistical analysis count the thickness, water content, ash content, fiber content and organoleptic test of texture, color, aroma, and taste of nata de watermelon pulp. The result show...

  13. UV-C photolysis of endocrine disruptors. The influence of inorganic peroxides

    International Nuclear Information System (INIS)

    Rivas, Javier; Gimeno, Olga; Borralho, Teresa; Carbajo, Maria

    2010-01-01

    Norfloxacin, doxycycline and mefenamic acid have been photolysed with UV-C radiation (254 nm) in the presence and absence of inorganic peroxides (hydrogen peroxide or sodium monopersulfate). Quantum yields in the range (1.1-4.5) x 10 -3 mol Einstein -1 indicate the low photo-reactivity of these pharmaceuticals. Inorganic peroxides considerably enhanced the contaminants conversion, although no appreciable mineralization could be obtained. A simplistic reaction mechanism for the hydrogen peroxide promoted experiments allowed for a rough estimation of the rate constant between hydroxyl radicals and norfloxacin (k > 1 x 10 9 M -1 s -1 ), doxycycline (k > 1.5 x 10 9 M -1 s -1 ) and mefenamic acid (k > 11.0 x 10 9 M -1 s -1 ).

  14. In vitro and in vivo antioxidant activity of the pulp of Jatobá-do-cerrado

    Directory of Open Access Journals (Sweden)

    Daniela Granja ARAKAKI

    2016-03-01

    Full Text Available Abstract Oxygen metabolism in cells causes the production of free radicals, which produce damage, including changes in cell structure and function. Antioxidants are substances that, at low concentrations, slow down or prevent oxidation. Fruits and vegetables contribute to the dietary supply of these compounds. The flora of the Cerrado in Brazil has shown to have high levels of bioactive compounds. This study aimed to characterize the antioxidant activity of the pulp of jatobá-do-cerrado in vitro and in vivo.In vitro antioxidant activity of the aqueous, ethanol and aqueous acetone extracts was evaluated by the DPPH method. We determined total phenols by the Folin-Ciocalteu assay and tannins by the Folin-Denis method.In vivo antioxidant potential of the aqueous acetone extract was evaluated by the TBARS technique. The aqueous acetone extract had the highest antioxidant capacity, followed by the aqueous and ethanol extracts. The same pattern occurred in the extraction of phenols and in the extraction of tannins. In vivo administration of the aqueous acetone extract inhibited lipid peroxidation compared to the control group. The inhibition of peroxidation has increased by elevating the dosage concentration of the extracts, demonstrating a significant antioxidant potential in vivo as well as in vitro.

  15. Phenolic extract of Dialium guineense pulp enhances reactive oxygen species detoxification in aflatoxin B₁ hepatocarcinogenesis.

    Science.gov (United States)

    Adeleye, Abdulwasiu O; Ajiboye, Taofeek O; Iliasu, Ganiyat A; Abdussalam, Folakemi A; Balogun, Abdulazeez; Ojewuyi, Oluwayemisi B; Yakubu, Musa T

    2014-08-01

    This study investigated the effect of Dialium guineense pulp phenolic extract on aflatoxin B1 (AFB1)-induced oxidative imbalance in rat liver. Reactive oxygen species (ROS) scavenging potentials of free and bound phenolic extract of D. guineense (0.2-1.0 mg/mL) were investigated in vitro using 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical, superoxide ion (O2(-)), hydrogen peroxide (H2O2), hydroxyl radical, and ferric ion reducing system. In the in vivo study, 35 animals were randomized into seven groups of five rats each. Free and bound phenolic extract (1 mg/mL) produced 66.42% and 93.08%, 57.1% and 86.0%, 62.0% and 90.05%, and 60.11% and 72.37% scavenging effect on DPPH radical, O2(-) radical, H2O2, and hydroxyl radical, while ferric ion was significantly reduced. An AFB1-mediated decrease in the activities of ROS detoxifying enzymes (superoxide dismutase, catalase, glutathione peroxidase, glutathione reductase, and glucose 6 phosphate dehydrogenase) was significantly attenuated (P<.05). AFB1-mediated elevation in the concentrations of oxidative stress biomarkers; malondialdehyde, conjugated dienes, lipid hydroperoxides, protein carbonyl, and percentage DNA fragmentation were significantly lowered by D. guineense phenolic extract (P<.05). Overall, the in vitro and in vivo effects suggest that D. guineense phenolic extract elicited ROS scavenging and detoxification potentials, as well as the capability of preventing lipid peroxidation, protein oxidation, and DNA fragmentation.

  16. Comparative studies on sulfur, peroxide, and radiation vulcanization of EFDM rubber

    International Nuclear Information System (INIS)

    Abdel-Aziz, M.M.; Basfar, A.A.; Mofti, S.

    2000-01-01

    The temperature and concentration dependence of the vulcanization characteristics and mechanical properties of epdm rubber containing various concentrations of peroxide compounds was studied. The peroxides used are Luperox Di, Luperox 500-40 Ke, peroximon Dc Sc and peroximon Dc 40 Ke. The optimum cure parameters for the different types of peroxides indicated that Luperox Di, relatively, Give the best properties among the studied peroxides. The mechanical properties of EPDM containing different concentrations of Luperox Di and vulcanized at different temperatures were compared with those of either radiation or sulfur-cured EPDM. The modulus stress and tensile strength of the Luperox Di-cured EPDM were found to increase with either increasing the temperature of vulcanization and/ or concentration of the peroxide. Moreover, the tensile strength values are much higher than those of the sulfur-cured samples, except for those with low concentration of peroxide and vulcanized at relatively low temperature. A comparable result to those of the chemically vulcanized samples was attained by the radiation- vulcanized samples containing 1 phr of crosslinking agent and irradiated to 150 KGy

  17. Energy Efficient Catalytic Activation of Hydrogen peroxide for Green Chemical Processes: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Collins, Terrence J.; Horwitz, Colin

    2004-11-12

    A new, highly energy efficient approach for using catalytic oxidation chemistry in multiple fields of technology has been pursued. The new catalysts, called TAML® activators, catalyze the reactions of hydrogen peroxide and other oxidants for the exceptionally rapid decontamination of noninfectious simulants (B. atrophaeus) of anthrax spores, for the energy efficient decontamination of thiophosphate pesticides, for the facile, low temperature removal of color and organochlorines from pulp and paper mill effluent, for the bleaching of dyes from textile mill effluents, and for the removal of recalcitrant dibenzothiophene compounds from diesel and gasoline fuels. Highlights include the following: 1) A 7-log kill of Bacillus atrophaeus spores has been achieved unambiguously in water under ambient conditions within 15 minutes. 2) The rapid total degradation under ambient conditions of four thiophosphate pesticides and phosphonate degradation intermediates has been achieved on treatment with TAML/peroxide, opening up potential applications of the decontamination system for phosphonate structured chemical warfare agents, for inexpensive, easy to perform degradation of stored and aged pesticide stocks (especially in Africa and Asia), for remediation of polluted sites and water bodies, and for the destruction of chemical warfare agent stockpiles. 3) A mill trial conducted in a Pennsylvanian bleached kraft pulp mill has established that TAML catalyst injected into an alkaline peroxide bleach tower can significantly lower color from the effluent stream promising a new, more cost effective, energy-saving approach for color remediation adding further evidence of the value and diverse engineering capacity of the approach to other field trials conducted on effluent streams as they exit the bleach plant. 4) Dibenzothiophenes (DBTs), including 4,6-dimethyldibenzothiophene, the most recalcitrant sulfur compounds in diesel and gasoline, can be completely removed from model gasoline

  18. Hydrogen peroxide as a sustainable energy carrier: Electrocatalytic production of hydrogen peroxide and the fuel cell

    International Nuclear Information System (INIS)

    Fukuzumi, Shunichi; Yamada, Yusuke; Karlin, Kenneth D.

    2012-01-01

    This review describes homogeneous and heterogeneous catalytic reduction of dioxygen with metal complexes focusing on the catalytic two-electron reduction of dioxygen to produce hydrogen peroxide. Whether two-electron reduction of dioxygen to produce hydrogen peroxide or four-electron O 2 -reduction to produce water occurs depends on the types of metals and ligands that are utilized. Those factors controlling the two processes are discussed in terms of metal–oxygen intermediates involved in the catalysis. Metal complexes acting as catalysts for selective two-electron reduction of oxygen can be utilized as metal complex-modified electrodes in the electrocatalytic reduction to produce hydrogen peroxide. Hydrogen peroxide thus produced can be used as a fuel in a hydrogen peroxide fuel cell. A hydrogen peroxide fuel cell can be operated with a one-compartment structure without a membrane, which is certainly more promising for the development of low-cost fuel cells as compared with two compartment hydrogen fuel cells that require membranes. Hydrogen peroxide is regarded as an environmentally benign energy carrier because it can be produced by the electrocatalytic two-electron reduction of O 2 , which is abundant in air, using solar cells; the hydrogen peroxide thus produced could then be readily stored and then used as needed to generate electricity through the use of hydrogen peroxide fuel cells.

  19. Hydrogen Peroxide as a Sustainable Energy Carrier: Electrocatalytic Production of Hydrogen Peroxide and the Fuel Cell.

    Science.gov (United States)

    Fukuzumi, Shunichi; Yamada, Yusuke; Karlin, Kenneth D

    2012-11-01

    This review describes homogeneous and heterogeneous catalytic reduction of dioxygen with metal complexes focusing on the catalytic two-electron reduction of dioxygen to produce hydrogen peroxide. Whether two-electron reduction of dioxygen to produce hydrogen peroxide or four-electron O 2 -reduction to produce water occurs depends on the types of metals and ligands that are utilized. Those factors controlling the two processes are discussed in terms of metal-oxygen intermediates involved in the catalysis. Metal complexes acting as catalysts for selective two-electron reduction of oxygen can be utilized as metal complex-modified electrodes in the electrocatalytic reduction to produce hydrogen peroxide. Hydrogen peroxide thus produced can be used as a fuel in a hydrogen peroxide fuel cell. A hydrogen peroxide fuel cell can be operated with a one-compartment structure without a membrane, which is certainly more promising for the development of low-cost fuel cells as compared with two compartment hydrogen fuel cells that require membranes. Hydrogen peroxide is regarded as an environmentally benign energy carrier because it can be produced by the electrocatalytic two-electron reduction of O 2 , which is abundant in air, using solar cells; the hydrogen peroxide thus produced could then be readily stored and then used as needed to generate electricity through the use of hydrogen peroxide fuel cells.

  20. Bioceramic/Poly (glycolic-poly (lactic acid composite induces mineralized barrier after direct capping of rat tooth pulp tissue

    Directory of Open Access Journals (Sweden)

    Alfonso Gala-Garcia

    2010-03-01

    Full Text Available The aim of this study was to observe the histopathological pulp response following direct pulp capping of mechanically exposed teeth in rats with a composite of beta-tricalcium phosphate-hydroxyapatite bioceramic (BC and poly (glycolic-poly (lactic acid (PLGA material or a calcium hydroxide [Ca(OH2] material, compared to BC alone and a negative control of water. Pulp of the maxillary molars was exposed, followed by capping with the experimental material. The pulpal tissue response was assessed post-operatively at 1, 7, 14 and 30 d, followed by histological analysis. The Ca(OH2 group exhibited severe acute inflammatory cell infiltration at day 14. However after 30 d, a new hard tissue with macro porous obliteration of the pulp chamber and a characteristic necrotic area had appeared. BC and Ca(OH2 capping were associated with moderate inflammation and dentinal bridge similar. Meanwhile, in the BC/PLGA composite group, there was moderate inflammatory infiltrate and formation of a dense and complete dentinal bridge. In conclusion, the BC/PLGA composite material showed a large zone of tertiary dentin, and effectively reorganized the dentin-pulp complex.

  1. Evaluation of the antihypertensive properties of yellow passion fruit pulp (Passiflora edulis Sims f. flavicarpa Deg.) in spontaneously hypertensive rats.

    Science.gov (United States)

    Konta, Eliziane Mieko; Almeida, Mara Ribeiro; do Amaral, Cátia Lira; Darin, Joana Darc Castania; de Rosso, Veridiana V; Mercadante, Adriana Zerlotti; Antunes, Lusânia Maria Greggi; Bianchi, Maria Lourdes Pires

    2014-01-01

    Various species of the genus Passiflora have been extensively used in traditional medicine as sedatives, anxiolytics, diuretics and analgesics. In the present study, after the identification and quantification of phytochemical compounds from yellow passion fruit pulp by liquid chromatography-photodiode array-mass spectrometry (HPLC-PDA-MS/MS), its antihypertensive effect was investigated on spontaneously hypertensive rats. Additionally, the renal function, evaluated by kidney/body weight, serum creatinine, proteinuria, urinary flow, reduced glutathione (GSH) levels and thiobarbituric acid-reactive substances (TBARS) and mutagenicity in bone marrow cells were assessed to evaluate the safety of passion fruit consumption. Yellow passion fruit pulp (5, 6 or 8 g/kg b.w.) was administered by gavage once a day for 5 consecutive days. HLPC-PDA-MS/MS analysis revealed that yellow passion fruit pulp contains phenolic compounds, ascorbic acid, carotenoids and flavonoids. The highest dose of passion fruit pulp significantly reduced the systolic blood pressure, increased the GSH levels and decreased TBARS. There were no changes in renal function parameters or the frequency of micronuclei in bone marrow cells. In conclusion, the antihypertensive effect of yellow passion fruit pulp, at least in part, might be due to the enhancement of the antioxidant status. The exact mechanisms responsible by this effect need further investigation. Copyright © 2013 John Wiley & Sons, Ltd.

  2. Study on Effectiveness of Processed and Unprocessed Black Liquor pulps in improving the properties of PPC mortar, Concrete and SCC

    Science.gov (United States)

    Ananthkumar, M.; Sathyan, Dhanya; Prabha, B.

    2018-02-01

    The cost of construction materials is increasing day by day because of high demand, scarcity of raw materials and high price of energy. From the view point of energy saving and over consumption of resources, the use of alternative constituents in construction materials is now a global concern. From this, the extensive research and development works towards exploring new ingredients are required for producing sustainable and environment friendly construction materials. Bagasse pulp liquor is one such material that can be used as a chemical admixture which is obtained as a by-product of paper manufacturing process. Around 5 million tons of bagasse pulp is obtained throughout the world each year. since the material is a waste product from paper industry, this can be changed as a admixture by its effective use in concrete. In the present investigation black pulp liquor is added to fresh concrete in different dosages, the concrete is then tested for workability, compressive strength, flexural, split tensile strength and setting time. From results it is shown that 1% replacement of water with black pulp liquor increases the fresh properties of the concrete, 2% replacement of water with black pulp liquor increases the mechanical properties of the concrete and acts as a set retarder.

  3. EFFLUENT TREATMENT FACILITY PEROXIDE DESTRUCTION CATALYST TESTING

    International Nuclear Information System (INIS)

    HALGREN DL

    2008-01-01

    The 200 Area Effluent Treatment Facility (ETF) main treatment train includes the peroxide destruction module (PDM) where the hydrogen peroxide residual from the upstream ultraviolet light/hydrogen peroxide oxidation unit is destroyed. Removal of the residual peroxide is necessary to protect downstream membranes from the strong oxidizer. The main component of the PDM is two reaction vessels utilizing granular activated carbon (GAC) as the reaction media. The PDM experienced a number of operability problems, including frequent plugging, and has not been utilized since the ETF changed to groundwater as the predominant feed. The unit seemed to be underperforming in regards to peroxide removal during the early periods of operation as well. It is anticipated that a functional PDM will be required for wastewater from the vitrification plant and other future streams. An alternate media or methodology needs to be identified to replace the GAC in the PDMs. This series of bench scale tests is to develop information to support an engineering study on the options for replacement of the existing GAC method for peroxide destruction at the ETF. A number of different catalysts will be compared as well as other potential methods such as strong reducing agents. The testing should lead to general conclusions on the viability of different catalysts and identify candidates for further study and evaluation

  4. Free toe pulp flap for finger pulp and volar defect reconstruction

    Directory of Open Access Journals (Sweden)

    Jyoshid R Balan

    2016-01-01

    Full Text Available Background: Fingertip injury requiring flap cover is very common in the modern era. The ideal cover should fulfill both functional and aesthetic improvement. Materials and Methods: From June 2015 to April 2016, we performed seven free toe pulp flaps for finger defect reconstruction. All patients were males. Five flaps were done in emergency post-traumatic cases, and two were done in elective set up. The cases included reconstruction of three thumbs, one index and one ring finger in an emergency set up and two ring fingers in the elective. Thumb reconstruction was done with great toe lateral pulp and the other digits reconstructed with second toe pulp flap. Follow-up evaluation included both functional and aesthetic assessment. Results: Five flaps survived completely, one suffered partial loss, and one flap failed completely. The median follow-up period was 9 months. The median duration of surgery was 255 min (range 210 to 300 min. The median two-point discrimination was 6.5 mm (range 4–8 mm. There was the return of temperature sensation in all patients; two had cold intolerance. The Semmes-Weinstein monofilament score varied from 3.61 to 5.07 (median filament index value 4.31/pressure value of 2 g/mm2. Three patients had delayed donor site wound healing. Conclusions: The free toe pulp flap is an efficient choice for fingertip and volar finger defects reconstruction with an excellent tissue match.

  5. Cell-derived micro-environment helps dental pulp stem cells promote dental pulp regeneration.

    Science.gov (United States)

    Zhang, Xuexin; Li, Hui; Sun, Jingjing; Luo, Xiangyou; Yang, Hefeng; Xie, Li; Yang, Bo; Guo, Weihua; Tian, Weidong

    2017-10-01

    The function of the dental pulp is closely connected to the extracellular matrix (ECM) structure, and ECM has received significant attention due to its biological functions for regulating cells. As such, the interaction between the ECM niche and cells is worth exploring for potential clinical uses. In this study, dental pulp stem cell (DPSC)-derived ECM (DPM) was prepared through cell culture and decellularization to function as the cell niche, and changes in DPSC behaviour and histological analysis of dental pulp tissue regeneration were evaluated following the DPM culture. DPM promoted the replication of DPSCs and exhibited retention of their mineralization. Then, the DPM-based culture strategy under odontogenic culture medium was further investigated, and the mineralization-related markers showed that DPSCs were regulated towards odontogenic differentiation. Dental pulp-like tissue with well-arranged ECM was harvested after a 2-month subcutaneous implantation in nude mice with DPM application. Additionally, DPSCs cultured on the plastic culture surface showed the up-regulation of mineralization makers in vitro, but there was a disorder in matrix formation and mineralization when the cells were cultured in vivo. DPM-based cultivation could serve as a cell niche and modulate DPSC behaviour, and this method also provided an alternative to harvest tissue-specific ECM and provided a strategy for ECM-cell interaction. © 2017 John Wiley & Sons Ltd.

  6. Functional analysis of a novel hydrogen peroxide resistance gene in Lactobacillus casei strain Shirota.

    Science.gov (United States)

    Serata, Masaki; Kiwaki, Mayumi; Iino, Tohru

    2016-11-01

    Lactic acid bacteria have a variety of mechanisms for tolerance to oxygen and reactive oxygen species, and these mechanisms differ among species. Lactobacillus casei strain Shirota grows well under aerobic conditions, indicating that the various systems involved in oxidative stress resistance function in this strain. To elucidate the mechanism of oxidative stress resistance in L. casei strain Shirota, we examined the transcriptome response to oxygen or hydrogen peroxide exposure. We then focused on an uncharacterized gene that was found to be up-regulated by both oxygen and hydrogen peroxide stress; we named the gene hprA1 (hydrogen peroxide resistance gene). This gene is widely distributed among lactobacilli. We investigated the involvement of this gene in oxidative stress resistance, as well as the mechanism of tolerance to hydrogen peroxide. Growth of L. casei MS105, an hprA1-disrupted mutant, was not affected by oxygen stress, whereas the survival rate of MS105 after hydrogen peroxide treatment was markedly reduced compared to that of the wild-type. However, the activity of MS105 in eliminating hydrogen peroxide was similar to that of the wild-type. We cloned hprA1 from L. caseiShirota and purified recombinant HprA1 protein from Escherichia coli. We demonstrated that the recombinant HprA1 protein bound to iron and prevented the formation of a hydroxyl radical in vitro. Thus, HprA1 protein probably contributes to hydrogen peroxide tolerance in L. casei strain Shirota by binding to iron in the cells and preventing the formation of a hydroxyl radical.

  7. Interappointment emergencies in teeth with necrotic pulps.

    Science.gov (United States)

    Alaçam, Tayfun; Tinaz, Ali Cemal

    2002-05-01

    The incidence of interappointment emergencies in symptomatic and asymptomatic teeth with necrotic pulps was evaluated, and severity of flare-ups was determined by a quantitative method using a flare-up index. There were no significant differences in the incidence of flare-ups attributable to gender, age, diameter of lesion, taking analgesics, placebos, or no medication, or preoperative symptomatic or asymptomatic tooth diagnoses (p > 0.05). There were significantly more painful flare-ups in mandibular teeth than in maxillary (p < 0.05).

  8. CD146 positive human dental pulp stem cells promote regeneration of dentin/pulp-like structures.

    Science.gov (United States)

    Matsui, Mikiko; Kobayashi, Tomoko; Tsutsui, Takeo W

    2018-04-01

    CD146 and STRO-1 are endothelial biomarkers that are co-expressed on the cellular membranes of blood vessels within human dental pulp tissue. This study characterized the percentage of dentin-like structures produced by CD146-positive (CD146 + ) human dental pulp stem cells (DPSCs), compared with their CD146-negative (CD146 - ) counterparts. DPSC populations were enriched using magnetic-activated cell sorting (MACS), yielding CD146 + and CD146 - cells, as well as mixtures composed of 25% CD146 + cells and 75% CD146 - cells (CD146 +/- ). Cell growth assays indicated that CD146 + cells exhibit an approximate 3-4 h difference in doubling time, compared with CD146 - cells. Cell cycle distributions were determined by flow cytometry analysis. The low percentage of CD146 + cells' DNA content in G 0 /G 1 phase were compared with CD146 - and non-separated cells. In contrast to CD146 - and non-separated cells, prompt mineralization was observed in CD146 + cells. Subsequently, qRT-PCR revealed high mRNA expression of CD146 and Alkaline phosphatase in mineralization-induced CD146 + cells. CD146 + cells were also observed high adipogenic ability by Oil red O staining. Histological examinations revealed an increased area of dentin/pulp-like structures in transplanted CD146 + cells, compared with CD146 - and CD146 +/- cells. Immunohistochemical studies detected dentin matrix protein-1 (DMP1) and dentin sialophosphoprotein (DSPP), as well as human mitochondria, in transplanted DPSCs. Co-expression of CD146 and GFP indicated that CD146 was expressed in transplanted CD146 + cells. CD146 + cells may promote mineralization and generate dentin/pulp-like structures, suggesting a role in self-renewal of stem cells and dental pulp regenerative therapy.

  9. Influence of moderate to severe chronic periodontitis on dental pulp.

    Science.gov (United States)

    Fatemi, K; Disfani, R; Zare, R; Moeintaghavi, A; Ali, Saadat A; Boostani, H R

    2012-10-01

    The relationship between periodontal disease and dental pulp changes is controversial and has been debated for many years. This human study was performed to evaluate the possible effects of moderate to advanced periodontal disease on the different aspect of dental pulp structure. Twenty hopeless permanent teeth were extracted from systemically healthy adults because of moderate to advanced chronic periodontitis, with a bone loss of >6 mm and a mobility of grade 2 or 3. Upon extraction, the apical 2 to 3 mm of the roots were immediately sectioned. Four to five sections were mounted on each slide, and every third slide was stained with hematoxylin and eosin. The specimens were histologically processed and examined by an oral pathologist. Non-inflamed pulp, with partial or complete necrosis in some sections and several non-necrotic sections, was found in only 6.3% of teeth. Most teeth (58.3%) displayed edematous pulps. Slightly fibrotic pulps were seen in 52.1% of sections. Odontoblastic integrity was seen in 31.3% of teeth. Most teeth (77.1%) displayed no pulp stones. In 43.8% of teeth, the pulp vessels displayed dilatation. Moderate to advanced periodontal disease can affect the dental pulp. Careful consideration of diagnostic and treatment planing in patients with endodontic-periodontal involvement is therefore recommended.

  10. Influence of moderate to severe chronic periodontitis on dental pulp

    Science.gov (United States)

    Fatemi, K; Disfani, R; Zare, R; Moeintaghavi, A; Ali, Saadat A.; Boostani, H. R

    2012-01-01

    Background: The relationship between periodontal disease and dental pulp changes is controversial and has been debated for many years. This human study was performed to evaluate the possible effects of moderate to advanced periodontal disease on the different aspect of dental pulp structure. Materials and Methods: Twenty hopeless permanent teeth were extracted from systemically healthy adults because of moderate to advanced chronic periodontitis, with a bone loss of >6 mm and a mobility of grade 2 or 3. Upon extraction, the apical 2 to 3 mm of the roots were immediately sectioned. Four to five sections were mounted on each slide, and every third slide was stained with hematoxylin and eosin. The specimens were histologically processed and examined by an oral pathologist. Results: Non-inflamed pulp, with partial or complete necrosis in some sections and several non-necrotic sections, was found in only 6.3% of teeth. Most teeth (58.3%) displayed edematous pulps. Slightly fibrotic pulps were seen in 52.1% of sections. Odontoblastic integrity was seen in 31.3% of teeth. Most teeth (77.1%) displayed no pulp stones. In 43.8% of teeth, the pulp vessels displayed dilatation. Conclusions: Moderate to advanced periodontal disease can affect the dental pulp. Careful consideration of diagnostic and treatment planing in patients with endodontic-periodontal involvement is therefore recommended. PMID:23493524

  11. Differentiation ability of rat postnatal dental pulp cells in vitro.

    NARCIS (Netherlands)

    Zhang, W.; Walboomers, X.F.; Wolke, J.G.C.; Bian, Z.; Fan, M.W.; Jansen, J.A.

    2005-01-01

    The current rapid progression in stem cell research has enhanced our knowledge of dental tissue regeneration. In this study, rat dental pulp cells were isolated and their differentiation ability was evaluated. First, dental pulp cells were obtained from maxillary incisors of male Wistar rats.

  12. 78 FR 38877 - Kraft Pulp Mills NSPS Review

    Science.gov (United States)

    2013-06-28

    ... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 60 [EPA-HQ-OAR-2012-0640] FRL-9829-3 RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... comments on the May 23, 2013, proposed rule titled, ``Kraft Pulp Mills NSPS Review'' is being extended by...

  13. Eggshells – assisted hydrolysis of banana pulp for biogas production

    African Journals Online (AJOL)

    KARAKANA

    In this study, pretreatment of banana pulp using eggshells in both calcined and un-calcined forms to examine the ... Key words: Anaerobic digestion, banana pulp hydrolysis biogas, eggshells. .... obtain fine powder. ..... using pig waste and cassava peels. ... from bioethanol waste: the effect of pH and urea addition to biogas.

  14. Nemesia root hair response to paper pulp substrate for micropropagation.

    Science.gov (United States)

    Labrousse, Pascal; Delmail, David; Decou, Raphaël; Carlué, Michel; Lhernould, Sabine; Krausz, Pierre

    2012-01-01

    Agar substrates for in vitro culture are well adapted to plant micropropagation, but not to plant rooting and acclimatization. Conversely, paper-pulp-based substrates appear as potentially well adapted for in vitro culture and functional root production. To reinforce this hypothesis, this study compares in vitro development of nemesia on several substrates. Strong differences between nemesia roots growing in agar or in paper-pulp substrates were evidenced through scanning electron microscopy. Roots developed in agar have shorter hairs, larger rhizodermal cells, and less organized root caps than those growing on paper pulp. In conclusion, it should be noted that in this study, in vitro microporous substrates such as paper pulp lead to the production of similar root hairs to those found in greenhouse peat substrates. Consequently, if agar could be used for micropropagation, rooting, and plant acclimatization, enhancement could be achieved if rooting stage was performed on micro-porous substrates such as paper pulp.

  15. Path analysis for selection of feijoa with greater pulp weight

    Directory of Open Access Journals (Sweden)

    Joel Donazzolo

    Full Text Available ABSTRACT: The objective of this paper was to identify the direct and indirect effects of feijoa fruits (Acca sellowiana traitson pulp weight, in order to use these traits in indirect genotypes selection. Fruits of five feijoa plants were collected in Rio Grande do Sul, in the years of 2009, 2010 and 2011. Six traits were evaluated: diameter, length, total weight, pulp weight, peel thickness and number of seeds per fruit. In the path analysis, with or without ridge regression, pulp weight was considered as the basic variable, and the other traits were considered as explanatory variables. Total weight and fruit diameter had high direct effect, and are the main traits associated with pulp weight. These traits may serve as criteria for indirect selection to increase feijoa pulp weight, since they are easy to be measured.

  16. Holdup time measurement by radioactive tracers in pulp production

    International Nuclear Information System (INIS)

    Roetzer, H.; Donhoffer, D.

    1988-12-01

    A batch of pulp was to be labelled before passing two bleaching towers of a pulp plant. Activated glass fibres were used as a tracer, which contained 24-Na with a half-life of 15 hours. It was shown in laboratory tests, that the glass fibres were suitable for transport studies of wood pulp. For use in the tests the fibres were activated and suspended in water. Due to the small diameter of the fibres (2-5 micrometers) this suspension shows physical properties very similar to the pulp. For detection six scintillation probes were mounted at different positions outside the bleaching tower. Radiation protection during the test was very easy due to the low total activity of the tracer material. Residence time distributions for both towers were measured. The successful tracer experiments show, that the method of labelling is suited for investigations of material transport in the pulp and paper industry. 3 figs., 11 refs., 2 tabs. (Author)

  17. PROCESS OF ELIMINATING HYDROGEN PEROXIDE IN SOLUTIONS CONTAINING PLUTONIUM VALUES

    Science.gov (United States)

    Barrick, J.G.; Fries, B.A.

    1960-09-27

    A procedure is given for peroxide precipitation processes for separating and recovering plutonium values contained in an aqueous solution. When plutonium peroxide is precipitated from an aqueous solution, the supernatant contains appreciable quantities of plutonium and peroxide. It is desirable to process this solution further to recover plutonium contained therein, but the presence of the peroxide introduces difficulties; residual hydrogen peroxide contained in the supernatant solution is eliminated by adding a nitrite or a sulfite to this solution.

  18. COD removal from pulp and paper effluents by Advanced Oxidation Processes (AOP); COD:n vaehentaeminen aop-menetelmaellae metsaeteollisuuden jaetevesistae - EKY 04

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, K; Wikberg, H [Kemira Chemicals Oy, Vaasa (Finland)

    1999-12-31

    The aim of this project is to develop a process where COD from pulp and paper industry can be removed by an AOP process. AOP is a process utilizing the oxidation power of the hydroxyl radical, which can be produced in many different ways. Compared to evaporation and membrane techniques, the benefits of this process are lack of condense, concentrate and sludge. It is a very simple process, based on adjusting the COD removal by means of hydrogen peroxide dosage. The study focuses on using heterogeneous catalyst together with hydrogen peroxide to produce hydroxyl radicals in order to remove COD at low temperatures (< 100 deg C) and normal pressures. The project started by screening catalysts able to perform this task in laboratory scale. Later on pilot scale equipment will be constructed for use in pulp and paper mill trials. The project will be carried out during 1997-1999. The study started by screening the possibilities of different catalysts together with hydrogen peroxide to remove phenols from a model water. Sofar, about hundred catalysts have been screened. These tests show that many of the heterogeneous catalysts are working, but most of them have actually dissolved in the water and `translated` to homogenous catalysts. This means that they cannot be used in this project. A few catalysts have been found to meet the targets for synthetic phenol waters. Next step will be to test these catalysts on actual water samples from pulp and paper mills, and after that a pilot and full-scale trial will be planned. In these trials we will find out which mill streams are possible to treat, and the cost/performances of a system totally based on the catalyst in use. Also, measurements of catalyst leaching and clogging will be made during these tests. The last test series is planned to be a full-scale trial. (orig.)

  19. COD removal from pulp and paper effluents by Advanced Oxidation Processes (AOP); COD:n vaehentaeminen aop-menetelmaellae metsaeteollisuuden jaetevesistae - EKY 04

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, K.; Wikberg, H. [Kemira Chemicals Oy, Vaasa (Finland)

    1998-12-31

    The aim of this project is to develop a process where COD from pulp and paper industry can be removed by an AOP process. AOP is a process utilizing the oxidation power of the hydroxyl radical, which can be produced in many different ways. Compared to evaporation and membrane techniques, the benefits of this process are lack of condense, concentrate and sludge. It is a very simple process, based on adjusting the COD removal by means of hydrogen peroxide dosage. The study focuses on using heterogeneous catalyst together with hydrogen peroxide to produce hydroxyl radicals in order to remove COD at low temperatures (< 100 deg C) and normal pressures. The project started by screening catalysts able to perform this task in laboratory scale. Later on pilot scale equipment will be constructed for use in pulp and paper mill trials. The project will be carried out during 1997-1999. The study started by screening the possibilities of different catalysts together with hydrogen peroxide to remove phenols from a model water. Sofar, about hundred catalysts have been screened. These tests show that many of the heterogeneous catalysts are working, but most of them have actually dissolved in the water and `translated` to homogenous catalysts. This means that they cannot be used in this project. A few catalysts have been found to meet the targets for synthetic phenol waters. Next step will be to test these catalysts on actual water samples from pulp and paper mills, and after that a pilot and full-scale trial will be planned. In these trials we will find out which mill streams are possible to treat, and the cost/performances of a system totally based on the catalyst in use. Also, measurements of catalyst leaching and clogging will be made during these tests. The last test series is planned to be a full-scale trial. (orig.)

  20. Investigation of pulping and paper making potential of weeds

    Directory of Open Access Journals (Sweden)

    omid Ghaffarzadeh Mollabashi

    2017-08-01

    Full Text Available Increasing use of wood products accompanying with resource constraint has revealed the importance of nonwood based material. In this study, pulping and papermaking potential of three varieties of weeds including Xanthium spinosum, Carthamus tinctorius and Cyperus papyrus have been considered. At first, chemical components of the samples i.e. cellulose, lignin and extractives have been measured following TAPPI standard test methods. Afterwards, pulping process based as soda and Kraft has been carried out and the pulp properties i.e. screen yield and reject, kappa number, caliper, bust index, tear index, brightness have been considered. According to the results, the amount cellulose, lignin and extractives have been measured for the Xanthium spinosum %38.15, %13.5 and 4.72, respectively. Theses parameters have been estimated about %38.25, %10.3 and % 2.95 for Carthamus tinctorius and %38.8, %19.2 and 4.4 in case of papyrus. The yield of soda and Kraft pulp of the papyrus was more than Xanthium spinosum and Carthamus tinctorius. Among all treatments, the highest screen yield related to soda pulping of Cyperus papyrus by %39.8 which has been obtained by 175 centigrade as a maximum temperature, L/W: 6/1, active alkaline: %30 and 90 minutes as the time at temperature. The lowest and highest amounts of the tear index were related to soda pulp sample of the Carthamus tinctorius and Kraft pulp sample of Xanthium spinosum by 2.49 and 8.1, respectively. In addition, the lowest and highest amounts of the bursting index were related to soda pulp sample of the Cyperus papyrus and Kraft pulp sample of Xanthium spinosum by 0.61and 2.48, respectively. Meanwhile, soda pulp sample of the Cyperus papyrus showed the highest amount of brightness with %45 ISO.

  1. Isolation and Characterization of Human Dental Pulp Stem Cells from Cryopreserved Pulp Tissues Obtained from Teeth with Irreversible Pulpitis.

    Science.gov (United States)

    Malekfar, Azin; Valli, Kusum S; Kanafi, Mohammad Mahboob; Bhonde, Ramesh R

    2016-01-01

    Human dental pulp stem cells (DPSCs) are becoming an attractive target for therapeutic purposes because of their neural crest origin and propensity. Although DPSCs can be successfully cryopreserved, there are hardly any reports on cryopreservation of dental pulp tissues obtained from teeth diagnosed with symptomatic irreversible pulpitis during endodontic treatment and isolation and characterization of DPSCs from such cryopreserved pulp. The aim of this study was to cryopreserve the said pulp tissues to propagate and characterize isolated DPSCs. A medium consisting of 90% fetal bovine serum and 10% dimethyl sulfoxide was used for cryopreservation of pulp tissues. DPSCs were isolated from fresh and cryopreserved pulp tissues using an enzymatic method. Cell viability and proliferation were determined using the MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assay. DPSC migration and interaction were analyzed with the wound healing assay. Mesenchymal characteristics of DPSCs were verified by flow cytometric analysis of cell surface CD markers. The osteogenic and adipogenic potential of DPSCs was shown by von Kossa and oil red O staining methods, respectively, and the polymerase chain reaction method. We found no significant difference in CD marker expression and osteogenic and adipogenic differentiation potential of DPSCs obtained from fresh and cryopreserved dental pulp tissue. Our study shows that dental pulp can be successfully cryopreserved without losing normal characteristics and differentiation potential of their DPSCs, thus making them suitable for dental banking and future therapeutic purposes. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  2. Hygroscopic behavior of lyophilized acerola pulp powder

    Directory of Open Access Journals (Sweden)

    Luciana C. Ribeiro

    2016-03-01

    Full Text Available ABSTRACT Powder products are characterized by their practicality and long life. However, fruit powders have high hygroscopicity and tend to agglomerate due to its hydrophilic nature. The isotherms of equilibrium moisture content apply to the study of dehydrated food preservation potential. Acerola is a nutritionally rich fruit, with great economic and industrial potential. The objective of this study was to analyse acerola powder adsorption isotherms obtained by lyophilization and characterize the powder obtained from lyophilized acerola pulp. Analysis of hygroscopicity, solubility and degree of caking were performed. Isotherms were represented by the mathematical models of GAB, BET, Henderson and Oswin, at temperatures of 25, 35 and 45 °C. According to the results, the obtained powder showed hygroscopicity of 5.96 g of absorbed water 100g-1 of solids, solubility of 95.08% and caking of 14.12%. The BET model showed the best fit to the adsorption isotherms of the acerola pulp powder obtained by lyophilization. The obtained isotherm was of type III, with a "J" shape. There was an inversion of the effect of temperature on the isotherms of acerola powders.

  3. Impacts of heterogeneous reactions to atmospheric peroxides: Observations and budget analysis study

    Science.gov (United States)

    Qin, Mengru; Chen, Zhongming; Shen, Hengqing; Li, Huan; Wu, Huihui; Wang, Yin

    2018-06-01

    Atmospheric peroxides play important roles in atmospheric chemistry, acting as reactive oxidants and reservoirs of HOX and ROX radicals. Field measurements of atmospheric peroxides were conducted over urban Beijing from 2015 to 2016, including dust storm days, haze days and different seasons. We employed a box model based on RACM2 mechanism to conduct concentration simulation and budget analysis of hydrogen peroxide (H2O2) and peroxyacetic acid (PAA). In this study, heterogeneous reaction is found to be a significant sink for atmospheric H2O2 and PAA in urban Beijing. Here, we recommend a suitable uptake coefficient formula considering the water effect for model research of peroxides. It is found that H2O2 and PAA unexpectedly maintained considerable concentrations on haze days, even higher than that on non-haze days. This phenomenon is mainly ascribed to relatively high levels of volatile organic compounds and ozone on haze days. In addition, high levels of water vapor in pollution episode can promote not only the heterogeneous uptake to aerosol phase but also the production of H2O2. Atmospheric PAA formation is suggested to be sensitive to alkenes and NOX in urban Beijing. In particular, with the help of peroxides, sulfate formation rate from heterogeneous uptake could increase by ∼4 times on haze days, indicating the potential effect of peroxides on enhancement of aerosol oxidative property and secondary sulfate formation.

  4. Chemical pulping of waste pineapple leaves fiber for kraft paper production

    Directory of Open Access Journals (Sweden)

    Waham Ashaier Laftah

    2015-07-01

    Full Text Available The main objective of this study is to evaluate the implementation of acetone as a pulping agent for pineapple leaves. Mixtures of water and acetone with concentration of 1%, 3%, 5%, 7%, and 10% were used. The effects of soaking and delignification time on the paper properties were investigated. Thermal and physical properties of paper sheet were studied using thermogravimetric analysis (TGA and tearing resistance test respectively. The morphological properties were observed using microscope at 200× magnification. The paper sheet produced from pulping with 3% acetone concentration shows the highest mechanical properties. Papers strength was improved by increasing the delignification time. The delignification time was reduced by cooking the pineapple leaves at a temperature of 118 °C under applied pressure of 80 kPa which has remarkable effect on paper strength.

  5. Safe handling of potential peroxide forming compounds and their corresponding peroxide yielded derivatives.

    Energy Technology Data Exchange (ETDEWEB)

    Sears, Jeremiah Matthew; Boyle, Timothy J.; Dean, Christopher J.

    2013-06-01

    This report addresses recent developments concerning the identification and handling of potential peroxide forming (PPF) and peroxide yielded derivative (PYD) chemicals. PPF chemicals are described in terms of labeling, shelf lives, and safe handling requirements as required at SNL. The general peroxide chemistry concerning formation, prevention, and identification is cursorily presented to give some perspective to the generation of peroxides. The procedure for determining peroxide concentrations and the proper disposal methods established by the Hazardous Waste Handling Facility are also provided. Techniques such as neutralization and dilution are provided for the safe handling of any PYD chemicals to allow for safe handling. The appendices are a collection of all available SNL documentation pertaining to PPF/PYD chemicals to serve as a single reference.

  6. Mill Integration-Pulping, Stream Reforming and Direct Causticization for Black Liquor Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Adriaan van Heiningen

    2007-06-30

    agglomeration problems of the conversion of Na{sub 2}CO{sub 3} to (high sodium) titanates during gasification of black liquor in the presence of (low sodium) titanates or TiO{sub 2} (Task 2). MTCI/ThermoChem tested the performance and operability of the combined technology of steam reforming and direct causticization in their Process Development Unit (PDU) (Task 3). The specific objectives were: (1) to investigate how split sulfidity and polysulfide (+ AQ) pulping can be used to increase pulp fiber yield and properties compared to conventional kraft pulping; (2) to determine the economics of black liquor gasification combined with these pulping technologies in comparison with conventional kraft pulping and black liquor recovery; (3) to determine the effect of operating conditions on the kinetics of the titanate-based direct causticization reaction during black liquor gasification at relatively low temperatures ({le} 750 C); (4) to determine the mechanism of particle agglomeration during gasification of black liquor in the presence of titanates at relatively low temperatures ({le} 750 C); and (5) to verify performance and operability of the combined technology of steam reforming and direct causticization of black liquor in a pilot scale fluidized bed test facility.

  7. Development of hemicelluloses biorefineries for integration into kraft pulp mills

    Science.gov (United States)

    Ajao, Olumoye Abiodun

    The development and wide spread acceptance of production facilities for biofuels, biochemicals and biomaterials is an important condition for reducing reliance on limited fossil resources and transitioning towards a global biobased economy. Pulp and paper mills in North America are confronted with high energy prices, high production costs and intense competition from emerging economies and low demand for traditional products. Integrated forest biorefineries (IFBR) have been proposed as a mean to diversify their product streams, increase their revenue and become more sustainable. This is feasible because they have access to forest biomass, an established feedstock supply chain and wood processing experience. In addition, the integration of a biorefinery process that can share existing infrastructure and utilities on the site of pulp mill would significantly lower investment cost and associated risks. Kraft pulping mills are promising receptor processes for a biorefinery because they either possess a prehydrolysis step for extracting hemicelluloses sugars prior to wood pulping or it can be added by retrofit. The extracted hemicelluloses could be subsequently transformed into a wide range of value added products for the receptor mill. To successfully implement hemicelluloses biorefinery, novel processes that are technically and economically feasible are required. It is necessary to identify products that would be profitable, develop processes that are energy efficient and the receptor mill should be able to supply the energy, chemicals and material demands of the biorefinery unit. The objective of this thesis is to develop energy efficient and economically viable hemicelluloses biorefineries for integration into a Kraft pulping process. A dissolving pulp mill was the reference case study. The transformation of hemicellulosic sugars via a chemical and biochemical conversion pathway, with furfural and ethanol as representative products for each pathway was studied. In

  8. Banana fruit pulp and peel involved in antianxiety and antidepressant effects while invigorate memory performance in male mice: Possible role of potential antioxidants.

    Science.gov (United States)

    Samad, Noreen; Muneer, Aqsa; Ullah, Najeeb; Zaman, Aqal; Ayaz, M Mazhar; Ahmad, Ijaz

    2017-05-01

    The present study was aimed to investigate the anti-stress and memory enhancing effects of banana (Musa sapientum L.) fruit pulp and peel extract in male mice. Locally bred albino Wistar mice were divided into control and 2 test groups (n=10). Control rats received drinking water while test groups were treated with banana fruit pulp (600 mg/kg; oral administration) and extract of banana peel (400mg/kg; oral administration). Behavioral activities of animals were monitored 14 days post administration of banana pulp and peel extract. Depression-like symptoms were measured by forced swimming test (FST). Anxiety like behavior was monitored using light-dark activity (LDA) test and plus maze activity (PMA) test and memory functions of rats were assessed by morris water maze (MWM) test. Following 2 weeks animals were decapitated and brain was removed for estimation of antioxidant enzymes such as catalase (CAT), super oxide dismutase (SOD) and reduced glutathione (GSH). In the present study both banana peel and pulp increased the time spent in light box and open arm, suggesting anxiolytic effects. A significant decrease in immobility time was observed in FST in both banana pulp and peel treated animals suggesting antidepressant like effects. Moreover, learning and memory assessed by MWM showed decrease in time to reach platform in both short term and long term memory test suggested increased memory function in both banana pulp and peel treated animals as compared to control animals. The activities of all antioxidant enzymes were significantly (pbanana pulp and peel treated animals than control. It is concluded that both banana pulp and peel have anti-anxiety, antidepressant effect as well as strengthen the memory possibly via its antioxidant mechanism. Therefore, it is recommended that supplementation of banana could be taken a vital role in stress (anxiety and depression) relief and increased in memory function possibly by phyto-antioxidants.

  9. Performance of a Horizontal Triple Cylinder Type Pulping Machine

    Directory of Open Access Journals (Sweden)

    Sukrisno Widyotomo

    2011-05-01

    Full Text Available Pulping is one important step in wet coffee processing method. Pulping process usually uses a machine which constructed by wood or metal materials. A horizontal single cylinder type of fresh coffee cherries pulping machine is the most popular machine in coffee processing. One of the weaknesses of a horizontal single cylinder type of fresh coffee cherries pulping machine is higher in broken beans. Broken bean is one of mayor aspects in defect system that contribute to low quality. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal double cylinder type of fresh coffee cherries pulping machine which resulted in 12.6—21.4% of broken beans. To reduce percentage of broken beans, Indonesian Coffee and Cocoa Research Institute has developed and tested a horizontal triple cylinder type of fresh coffee cherries pulping machine. Material tested was fresh mature Robusta coffee cherries, 60—65% (wet basis moisture content; has classified on 3 levels i.e. unsorted, small and medium, and clean from metal and foreign materials. The result showed that the machine produced 6,340 kg/h in optimal capacity for operational conditions, 1400 rpm rotor rotation speed for unsorted coffee cherries with composition 55.5% whole parchment coffee, 3.66% broken beans, and 1% beans in wet skin.Key words : coffee, pulp, pulper, cylinder, quality.

  10. Scaffolds to Control Inflammation and Facilitate Dental Pulp Regeneration

    Science.gov (United States)

    Colombo, John S.; Moore, Amanda N.; Hartgerink, Jeffrey D.; D’Souza, Rena N.

    2014-01-01

    In dentistry, the maintenance of a vital dental pulp is of paramount importance, as teeth devitalized by root canal treatment may become more brittle and prone to structural failure over time. Advanced carious lesions can irreversibly damage the dental pulp by propagating a sustained inflammatory response throughout the tissue. While the inflammatory response initially drives tissue repair, sustained inflammation has an enormously destructive effect on the vital pulp, eventually leading to total necrosis of the tissue and necessitating its removal. The implications of tooth devitalization have driven significant interest in the development of bioactive materials that facilitate the regeneration of damaged pulp tissues by harnessing the capacity of the dental pulp for self-repair. In considering the process by which pulpitis drives tissue destruction, it is clear that an important step in supporting the regeneration of pulpal tissues is the attenuation of inflammation. Macrophages, key mediators of the immune response, may play a critical role in the resolution of pulpitis due to their ability to switch to a pro-resolution phenotype. This process can be driven by the resolvins, a family of molecules derived from fatty acids that show great promise as therapeutic agents. In this review, we outline the importance of preserving the capacity of the dental pulp to self-repair through the rapid attenuation of inflammation. Potential treatment modalities, such as shifting macrophages to a pro-resolving phenotype with resolvins are described, and a range of materials known to support the regeneration of dental pulp are presented. PMID:24698696

  11. Microarray expression profiling of human dental pulp from single subject.

    Science.gov (United States)

    Tete, Stefano; Mastrangelo, Filiberto; Scioletti, Anna Paola; Tranasi, Michelangelo; Raicu, Florina; Paolantonio, Michele; Stuppia, Liborio; Vinci, Raffaele; Gherlone, Enrico; Ciampoli, Cristian; Sberna, Maria Teresa; Conti, Pio

    2008-01-01

    Microarray is a recently developed simultaneous analysis of expression patterns of thousand of genes. The aim of this research was to evaluate the expression profile of human healthy dental pulp in order to find the presence of genes activated and encoding for proteins involved in the physiological process of human dental pulp. We report data obtained by analyzing expression profiles of human tooth pulp from single subjects, using an approach based on the amplification of the total RNA. Experiments were performed on a high-density array able to analyse about 21,000 oligonucleotide sequences of about 70 bases in duplicate, using an approach based on the amplification of the total RNA from the pulp of a single tooth. Obtained data were analyzed using the S.A.M. system (Significance Analysis of Microarray) and genes were merged according to their molecular functions and biological process by the Onto-Express software. The microarray analysis revealed 362 genes with specific pulp expression. Genes showing significant high expression were classified in genes involved in tooth development, protoncogenes, genes of collagen, DNAse, Metallopeptidases and Growth factors. We report a microarray analysis, carried out by extraction of total RNA from specimens of healthy human dental pulp tissue. This approach represents a powerful tool in the study of human normal and pathological pulp, allowing minimization of the genetic variability due to the pooling of samples from different individuals.

  12. Radiation induced peroxidation in model lipid systems

    International Nuclear Information System (INIS)

    Dahlan, K.Z.B.H.M.

    1981-08-01

    In the studies of radiation induced lipid peroxidation, lecithin-liposomes and aqueous micellar solutions of sodium linoleate (or linoleic acid) have been used as models of lipid membrane systems. The liposomes and aqueous linoleate micelles were irradiated in the presence of O 2 and N 2 O/O 2 (80/20 v/v). The peroxidation was initiated using gamma radiation from 60 Co radiation source and was monitored by measuring the increase in absorbance of conjugated diene at 232 nm and by the thiobarbituric acid (TBA) test. The oxidation products were also identified by GLC and GLC-MS analysis. (author)

  13. Precipitation of uranium concentrates by hydrogen peroxide

    International Nuclear Information System (INIS)

    Barbosa Filho, O.; Teixeira, L.A.C.

    1987-01-01

    An experimental study on the precipitation of uranyl peroxide (UO 4 x H 2 O) has been carried out in a laboratory scale. The objective was to assess the possibility of the peroxide route as an alternative to a conventional ammonium diuranate process. A factorial design was used to evaluate the effects of the initial pH, precipitation pH and H 2 O 2 /UO 2 2+ ratio upon the process. The responses were measured in terms of: efficiency of U precipitation, content of U in the precipitates, and distribution of impurities in the precipitates. (Author) [pt

  14. Uranium peroxide precipitate drying temperature relationships

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, C.; Dyck, B., E-mail: chick_rodgers@cameco.com [Cameco Corp., Saskatoon, SK (Canada)

    2010-07-01

    Cameco Corporation is in the process of revitalizing the mill at its Key Lake operation in northern Saskatchewan. The current Key Lake process employs ammonia stripping and ammonia precipitation. As part of the revitalization, the company is considering installing strong acid stripping in solvent extraction as used at its Rabbit Lake operation. This change would lead to using hydrogen peroxide for uranium precipitation. As part of the process evaluation, tests were carried out to study how changes in the temperature of an indirect fired dryer affected the properties of uranium peroxide [yellowcake] precipitate. This paper discusses the results of the test work, including the relationships between drying temperature and the following: (author)

  15. A modified efficient method for dental pulp stem cell isolation

    Directory of Open Access Journals (Sweden)

    Maryam Raoof

    2014-01-01

    Full Text Available Background: Dental pulp stem cells can be used in regenerative endodontic therapy. The aim of this study was to introduce an efficient method for dental pulp stem cells isolation. Materials and Methods: In this in-vitro study, 60 extracted human third molars were split and pulp tissue was extracted. Dental pulp stem cells were isolated by the following three different methods: (1 digestion of pulp by collagenase/dispase enzyme and culture of the released cells; (2 outgrowth of the cells by culture of undigested pulp pieces; (3 digestion of pulp tissue pieces and fixing them. The cells were cultured in minimum essential medium alpha modification (αMEM medium supplemented with 20% fetal bovine serum(FBS in humid 37°C incubator with 5% CO 2 . The markers of stem cells were studied by reverse transcriptase polymerase chain reaction (PCR. The student t-test was used for comparing the means of independent groups. P <0.05 was considered as significant. Results: The results indicated that by the first method a few cell colonies with homogenous morphology were detectable after 4 days, while in the outgrowth method more time was needed (10-12 days to allow sufficient numbers of heterogeneous phenotype stem cells to migrate out of tissue. Interestingly, with the improved third method, we obtained stem cells successfully with about 60% efficiency after 2 days. The results of RT-PCR suggested the expression of Nanog, Oct-4, and Nucleostemin markers in the isolated cells from dental pulps. Conclusion: This study proposes a new method with high efficacy to obtain dental pulp stem cells in a short time.

  16. Basic effects of pulp refining on fiber properties--a review.

    Science.gov (United States)

    Gharehkhani, Samira; Sadeghinezhad, Emad; Kazi, Salim Newaz; Yarmand, Hooman; Badarudin, Ahmad; Safaei, Mohammad Reza; Zubir, Mohd Nashrul Mohd

    2015-01-22

    The requirement for high quality pulps which are widely used in paper industries has increased the demand for pulp refining (beating) process. Pulp refining is a promising approach to improve the pulp quality by changing the fiber characteristics. The diversity of research on the effect of refining on fiber properties which is due to the different pulp sources, pulp consistency and refining equipment has interested us to provide a review on the studies over the last decade. In this article, the influence of pulp refining on structural properties i.e., fibrillations, fine formation, fiber length, fiber curl, crystallinity and distribution of surface chemical compositions is reviewed. The effect of pulp refining on electrokinetic properties of fiber e.g., surface and total charges of pulps is discussed. In addition, an overview of different refining theories, refiners as well as some tests for assessing the pulp refining is presented. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Effect of metal sulfide pulp density on gene expression of electron transporters in Acidithiobacillus sp. FJ2.

    Science.gov (United States)

    Fatemi, Faezeh; Miri, Saba; Jahani, Samaneh

    2017-05-01

    In Acidithiobacillus ferrooxidans, one of the most important bioleaching bacterial species, the proteins encoded by the rus operon are involved in the electron transfer from Fe 2+ to O 2 . To obtain further knowledge about the mechanism(s) involved in the adaptive responses of the bacteria to growth on the different uranium ore pulp densities, we analyzed the expression of the four genes from the rus operon by real-time PCR, when Acidithiobacillus sp. FJ2 was grown in the presence of different uranium concentrations. The uranium bioleaching results showed the inhibitory effects of the metal pulp densities on the oxidation activity of the bacteria which can affect Eh, pH, Fe oxidation and uranium extractions. Gene expression analysis indicated that Acidithiobacillus sp. FJ2 tries to survive in the stress with increasing in the expression levels of cyc2, cyc1, rus and coxB, but the metal toxicity has a negative effect on the gene expression in different pulp densities. These results indicated that Acidithiobacillus sp. FJ2 could leach the uranium even in high pulp density (50%) by modulation in rus operon gene responses.

  18. Enzyme Enhanced Protein Recovery from Green Biomass Pulp

    DEFF Research Database (Denmark)

    Dotsenko, Gleb; Lange, Lene

    2017-01-01

    of local protein resources based on upgrade from e.g. green plant biomass. In present work we consider different strategies for protein recovery from white clover and ryegrass screw press pulps, using aqueous extraction, as well as carbohydrases and proteases enhanced extraction. Protein recovery...... in these studies was determined as a yield of solubilized protein with regard to the total protein in a screw press pulp. Aqueous extraction at pH 8.0 resulted in approx. 40 % protein recovery, while proteases application (Savinase 16.0L, Novozymes) enabled twice higher protein yield. Application of plant cell...... pulp proteolyzates, generated by Savinase 16.0L protease....

  19. Competitiveness of wood pulp production in different Brazilian states

    Directory of Open Access Journals (Sweden)

    Naisy Silva Soares

    2013-06-01

    Full Text Available This work aimed to analyze the competitiveness of wood pulp production in different Brazilian states, in May, 2008 (Minas Gerais, São Paulo, Espírito Santo and Bahia, using the Policy Analysis Matrix (PAM. The results obtained indicated that the private and social profitability of wood pulp production and commercialization was positive and greater in Bahia. The Brazilian companies were penalized by public policies adopted for the sector; the wood pulp production in São Paulo and Bahia were more competitive and less exposed to the negative effects of public policies that reduce the national company profits.

  20. Using renewable sources in the pulp and paper mills

    International Nuclear Information System (INIS)

    Hazi, Aneta; Hazi, Gheorghe

    2007-01-01

    The pulp and paper industry is a major consumer of natural sources (wood) and energy (fossil fuels, electricity) and a significant contributor of pollutant discharges to the environment. In this paper there are presented pulp and paper making process and steam and power generation using renewable sources. This paper includes also an exergy analysis of the steam and power generation process for a pulp and paper mill. Based on the analysis, two sustainability indicators were calculated: the exergetic efficiency and the exergy renewability. (authors)

  1. Chemi-thermomechanical pulping of para rubber waste wood

    Energy Technology Data Exchange (ETDEWEB)

    Kubo, T.; Hosokawa, J.; Kobayashi, T.; Kobayashi, Y.

    1981-01-01

    The addition of NaOH to Na/sub 2/SO/sub 3/-treated waste wood chips (Hevea brasiliensis) increased long fiber fraction, Klason lignin content and bulk density, improved breaking length and tear factor, and decreased energy consumption in refining and brightness of resulting chemithermomechanical pulp. Lowering in brightness by alkali treatment was recovered by H/sub 2/O/sub 2/ bleaching, and bleaching with 8% H/sub 2/O/sub 2/ on pulp gave pulp with 61.3% brightness.

  2. Method and apparatus for assaying wood pulp fibers

    Science.gov (United States)

    Gustafson, Richard [Bellevue, WA; Callis, James B [Seattle, WA; Mathews, Jeffrey D [Neenah, WI; Robinson, John [Issaquah, WA; Bruckner, Carsten A [San Mateo, CA; Suvamakich, Kuntinee [Seattle, WA

    2009-05-26

    Paper pulp is added to a stain solution. The stain solution and pulp fibers are mixed to form a slurry. Samples are removed from the slurry and are admixed with dilution water and a bleach. Then, the fibers are moved into a flow cell where they are subjected to a light source adapted to stimulate fluorescence from the stained pulp fiber. Before the fiber slurry enters the flow cell it is mixed with a dilution water of bleach to reduce background fluorescence. The fluorescent light is collimated and directed through a dichroic filter onto a fluorescence splitting dichroic filter.

  3. Can Acceptable Pulp be Obtained from Eucalyptus globulus Wood Chips after Hemicellulose Extraction?

    OpenAIRE

    Francisco López; M. Trinidad García; Vicente Mena; J. Mauricio Loaiza; Minerva A. M. Zamudio; Juan C. García

    2014-01-01

    This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or be...

  4. Vascular endothelial growth factor and its relationship with the dental pulp.

    Science.gov (United States)

    Grando Mattuella, Leticia; Westphalen Bento, Leticia; de Figueiredo, José Antonio Poli; Nör, Jacques Eduardo; de Araujo, Fernando Borba; Fossati, Anna Christina Medeiros

    2007-05-01

    The dental pulp is a loose connective tissue located within rigid dentinal walls. Therefore, when subjected to a stimulus, the pulpal tissue has little expansion capacity. The defense mechanisms of this tissue include the formation of tertiary dentin as well as the production of signaling molecules that help in the repair. The dentin matrix is rich in growth factors (GFs) that, when diluted and diffused into the pulp tissue, aid the healing process of the dentinopulpar complex. The angiogenic GFs participate in this event. Vascular endothelial growth factor (VEGF), a potent mitogen for endothelial cells, promotes endothelial cell survival and angiogenesis. Among its receptors, VEGFR-2 seems to be the most intimately associated with mitogenic activities, cell migration, vascular permeability, and survival of endothelial cells. This literature review addresses the cell-signaling process that occurs in response to a pulp stimulus up to its transduction in the target cell, describing the VEGF, as well as its characteristics and receptors. The reported studies have correlated the expression of VEGF and its potential functions that may have an impact on several dental specialties, thus indicating that further clinical investigations should be conducted in order to translate the results obtained until this moment primarily in laboratory experiments.

  5. Cytoprotection mediated antiulcer effect of aqueous fruit pulp extract of Cucumis sativus

    Directory of Open Access Journals (Sweden)

    Swapnil Sharma

    2012-05-01

    Full Text Available Objective: The study was aimed to evaluate the gastroprotective potential of Cucumis Sativus fruit pulp aqueous extract (CSE in gastric ulcerated rats. Methods: Cytoprotective potential was evaluated via oral administration of CSE at the doses of 250, 500 &1000 mg/kg three times in a day, for 5 days before the induction of ulcers in indomethacin and pyloric ligation induced ulcer model. Further, its effects were studied on various parameters volume of gastric juice, pH, free and total acidity, protein concentration, acid output in gastric juice, lipid peroxide (LPO, and activities of enzymic antioxidants-super oxide dismutase (SOD and catalase (CAT in gastric mucosa. The levels of hexose, hexosamine, sialic acid, fucose in gastric mucosa and gastric juice were also examined. The extent of healing was also determined with post administration of CSE at the same doses & dosage schedule in acetic acid induced model. Results: In indomethacin and pyloric ligation model, the pretreatment with CSE and ranitidine significantly reduced the lesion index, in comparison with control treated group (P< 0.05. The percentages of protection of ulcers were 25.8, 65.7, 80.6 & 93.8 for the treated groups of CSE and ranitidine whereas in pyloric ligation it was 31.26, 55.18, 93.26 & 95.51 respectively. In pyloric ligation model, CSE resulted in significant increase in pH, enzymic antioxidants i.e. SOD & CAT, with a significant decrease in volume of gastric juice, free and total acidity, protein & carbohydrate concentration and LPO levels. In acetic acid inducer model, treatment with Cucumis sativus (CSE caused significant reduction in lesion index in when compared to control treated group, providing evidence for ulcer healing capacity of it. The presence of the flavonoids and polyphenols may be responsible for the gastroprotective effect of CSE. Conclusions: The aqueous fruit pulp extract of Cucumis sativus (CSE has a gastroprotective property.

  6. Vitamin C Supplementation Reduces Peroxidative Damage without ...

    African Journals Online (AJOL)

    Objective: This study was designed to assess the effects of vitamin C supplementation on the lung function tests and peroxidative damage in asthmatic children. Methodology: Fifteen asthmatics aged between 8 - 14 years, all in the stable state were used in this study. Three millilitres of blood were drawn from the antecubital ...

  7. Relationship Between Calorie Restriction, Lipid Peroxidation ...

    African Journals Online (AJOL)

    In the brain of the caloric restricted rats, there was little or no change in the tGSH and GSH, although the GSSG and GSSG/GSH% ratio were increased significantly. These results suggest that aging of rats had been decelerated by caloric restriction due to the decrease in the peroxidative damage in the lungs and brain.

  8. Nutrient contents of the fresh pulps and dried pulp cakes of vitellaria paradoxa of Gulu District, Uganda

    DEFF Research Database (Denmark)

    Oryema, Christine; Oryem-Origa, Hannington; Roos, Nanna

    2016-01-01

    Vitellaria paradoxa Gaertn locally known as ‘Yaa’ in Acholi is a valuable edible indigenous wild fruit in Gulu District, northern Uganda. It is a multipurpose fruit tree and highly favoured by the inhabitants of this district. Its fruit pulps are eaten when fresh and/or made into cakes and dried....... This study determined the nutrient compositions of the fresh pulps and dried pulp cakes of V. paradoxa. Laboratory analyses were undertaken to determine the micro and macro nutrients in the samples on fresh (FM) and dry matter (DM) basis following standard procedures and protocols. The potassium, sodium...

  9. Methods to use biomass, consisting of peat and wood material, to extract fiber substance to be used to make paper pulp and a fuel product. Saett att ur biomassa, bestaaende av torv och vedmatarial, utvinna en foer tillverkning av en pappersmassaprodukt laemplig fibermassa samt en braensleprodukt

    Energy Technology Data Exchange (ETDEWEB)

    Lindahl, J A.I.

    1985-12-16

    Peat cut from the upper layers is used to make paper pulp of low density. The wood material of the peat is mechanically separated three times. The result is a pulp of peat fibres and wood fibres and dewatered colloidal peat to be used as a fuel. (M.B).

  10. Pulp Stone, Haemodialysis, End-stage Renal Disease, Carotid Atherosclerosis

    OpenAIRE

    Patil, Santosh; Sinha, Nidhi

    2013-01-01

    Objectives: The aim of this study was to determine the relationship between the presence of pulp calcification and carotid artery calcification on the dental panoramic radiographs in End Stage Renal Disease (ESRD) patients who were on haemodialysis.

  11. UTILIZATION OF Prosopis afiicana PULP FOR RABBIT FEEDING: 2

    African Journals Online (AJOL)

    IBB

    The formulated diets contained similar crude protein content of 18%. The apparent ... These results indicate that Prosopis africana pulp can completely replace maize in the diets of ... serum albumin were determined by Biuret reactions. (Bush ...

  12. Processing pineapple pulp into dietary fibre supplement | Ackom ...

    African Journals Online (AJOL)

    Processing pineapple pulp into dietary fibre supplement. ... The pasting characteristics or properties of wheat flour fortified with the product up to 20 ... of some popular foods to help increase the fibre intake and health of the general population.

  13. Effects of feeding cassava pulp fermented with Acremonium ...

    African Journals Online (AJOL)

    Acer

    2017-01-27

    #, T. .... Briefly, 10 kg steamed cassava pulp (87.5% DM) was soaked with sterile water (1 : 1). .... The data on digestibility and retention of broilers are presented in Table 3. .... Taken together, the antioxidant capacity of A.

  14. Partial pulp necrosis caused by excessive orthodontic force

    Directory of Open Access Journals (Sweden)

    Min-Young Kim

    2011-03-01

    Full Text Available As the dental pulp is encased with a rigid, noncompliant shell, changes in pulpal blood flow or vascular tissue pressure can have serious implication for the health of pulp. Numerous studies have demonstrated that orthodontic force application may influence both blood flow and cellular metabolism, leading degenerative and/or inflammatory responses in the dental pulp. The aim of this case report is to present a case about tooth with chronic periapical abscess which showed normal vital responses. Excessive orthodontic force is thought to be the prime cause of partial pulp necrosis. Owing to remaining vital tissue, wrong dianosis can be made, and tooth falsely diagnosed as vital may be left untreated, causing the necrotic tissue to destroy the supporting tissuses. Clinician should be able to utilize various diagnostic tools for the precise diagnosis, and be aware of the endodontic-orthodontic inter-relationship.

  15. Proximate and Mineral Composition of the Pulp of Chrysophyllum ...

    African Journals Online (AJOL)

    MBI

    2014-11-13

    Nov 13, 2014 ... The results showed that the fruit pulp of Chrysophyllum albidum contained essential ... seed of the plant is a good source of oil which is ... Sample Collection and Treatment ... AAS machine due to its good precision and.

  16. NIRS Characterization of Paper Pulps to Predict Kappa Number

    Directory of Open Access Journals (Sweden)

    Ana Moral

    2015-01-01

    Full Text Available Rice is one of the most abundant food crops in the world and its straw stands as an important source of fibres both from an economic and an environmental point of view. Pulp characterization is of special relevance in works involving alternative raw materials, since pulp properties are closely linked to the quality of the final product. One of the analytical techniques that can be used in pulp characterization is near-infrared spectroscopy (NIRS. The use of NIRS has economic and technical advantages over conventional techniques. This paper aims to discuss the convenience of using NIRS to predict Kappa number in rice straw pulps produced under different conditions. We found that the resulting Kappa number can be acceptably estimated by NIRS, as the errors obtained with that method are similar to those found for other techniques.

  17. Factors influencing cassava - pulp fermentation period for gari ...

    African Journals Online (AJOL)

    Factors influencing cassava - pulp fermentation period for gari processing among ... Result of probit model analysis at 5% significance level shows an R value ... Marital status (2.236**) and respondents' cultural influences (1.960**) were ...

  18. Claustral single cell reactions to tooth pulp stimulation in cats.

    Science.gov (United States)

    Jastreboff, P; Sikora, M; Frydrychowski, A; Słoniewski, P

    1983-01-01

    Single unit activity in the central region of the claustrum, evoked by electrical stimulation of tooth pulp or paws was studied on cats under chloralose anesthesia. The majority of cells responded in similar manner to stimulation of tooth pulp or paws, but there were cells with clear preference to a given type of stimulation. Latencies of reactions evoked by tooth pulp stimulation were significantly shorter than those for limb stimulation. In the former case latencies as short as 8 rns were observed. It is postulated that the central region of the claustrum receives a projection from the tooth pulp, and that in those cases with very short latency the projection is direct and does not involve the cerebral cortex.

  19. Prevalence and Analysis of Factors Related to Occurrence of Pulp ...

    African Journals Online (AJOL)

    Uche

    between pulp stone and pristine posterior teeth, chronic periodontitis and posterior teeth ... Conclusion: It is recommended that researchers should pay special care in case selections, and ... (1982) reported a PS prevalence rate of 20.7 % in.

  20. Timing of pulp extirpation for replanted avulsed teeth.

    LENUS (Irish Health Repository)

    Stewart, Chris

    2009-01-01

    A search was performed (April 2004) across four databases, namely Ovid Medline, Cochrane Library, PubMed and Web of Science, relevant to the proposed PICO ( Patient or problem, Intervention, Comparison, Outcome) question: (P) for a replanted avulsed permanent tooth, (I) is early pulp extirpation within 10-14 days of replantation, (C) compared with delayed pulp extirpation, (O) associated an increased likelihood of successful periodontal healing after tooth replantation. Only articles published in the English language were considered.

  1. Pectin methyl esterase activity in apple and orange pulps

    International Nuclear Information System (INIS)

    Abdullaev, A.; Djumaev, B.B.; Djumaev, N.B.; Mukhidinov, Z.K.

    2008-01-01

    The results of pectin methyl esterase activity from apple, orange pulp and orange peel depending of ph and temperature are discussed. It's shown that the methyl esterase activity form apple and orange pulps higher in range of temperatures from +37...+60 d ig C . The analysis of dependence of its activity from ph has shown that in both case the enzyme activity increase with increase of ph

  2. Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

    Energy Technology Data Exchange (ETDEWEB)

    Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J., E-mail: rosemarymj@lifecarehll.com

    2016-04-01

    Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

  3. Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

    International Nuclear Information System (INIS)

    Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J.

    2016-01-01

    Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

  4. Pulp fictions of medieval England: Essays in popular romance

    OpenAIRE

    McDonald, Nicola

    2004-01-01

    Middle English popular romance is the most audacious and compendious testimony to the imaginary world of the English Middle Ages. Yet, with few exceptions, it remains under read and under studied. Pulp fictions of medieval England demonstrates that popular romance merits and rewards serious critical attention and that it is crucial to our understanding of the complex and conflicted world of medieval England. Pulp fictions of medieval England comprises ten essays on individual romances that, w...

  5. Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration

    OpenAIRE

    Keller, Laetitia; Offner, Damien; Schwint?, Pascale; Morand, David; Wagner, Quentin; Gros, Catherine; Bornert, Fabien; Bahi, Sophie; Musset, Anne-Marie; Benkirane-Jessel, Nadia; Fioretti, Florence

    2015-01-01

    The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be p...

  6. Pulp-dentin Regeneration: Current State and Future Prospects.

    Science.gov (United States)

    Cao, Y; Song, M; Kim, E; Shon, W; Chugal, N; Bogen, G; Lin, L; Kim, R H; Park, N-H; Kang, M K

    2015-11-01

    The goal of regenerative endodontics is to reinstate normal pulp function in necrotic and infected teeth that would result in reestablishment of protective functions, including innate pulp immunity, pulp repair through mineralization, and pulp sensibility. In the unique microenvironment of the dental pulp, the triad of tissue engineering would require infection control, biomaterials, and stem cells. Although revascularization is successful in resolving apical periodontitis, multiple studies suggest that it alone does not support pulp-dentin regeneration. More recently, cell-based approaches in endodontic regeneration based on pulpal mesenchymal stem cells (MSCs) have demonstrated promising results in terms of pulp-dentin regeneration in vivo through autologous transplantation. Although pulpal regeneration requires the cell-based approach, several challenges in clinical translation must be overcome-including aging-associated phenotypic changes in pulpal MSCs, availability of tissue sources, and safety and regulation involved with expansion of MSCs in laboratories. Allotransplantation of MSCs may alleviate some of these obstacles, although the long-term stability of MSCs and efficacy in pulp-dentin regeneration demand further investigation. For an alternative source of MSCs, our laboratory developed induced MSCs (iMSCs) from primary human keratinocytes through epithelial-mesenchymal transition by modulating the epithelial plasticity genes. Initially, we showed that overexpression of ΔNp63α, a major isoform of the p63 gene, led to epithelial-mesenchymal transition and acquisition of stem characteristics. More recently, iMSCs were generated by transient knockdown of all p63 isoforms through siRNA, further simplifying the protocol and resolving the potential safety issues of viral vectors. These cells may be useful for patients who lack tissue sources for endogenous MSCs. Further research will elucidate the level of potency of these iMSCs and assess their

  7. Seeking optimality in fruit pulping schedules: A case study*

    Directory of Open Access Journals (Sweden)

    J.H. Van Vuuren

    2014-01-01

    Full Text Available The process of scheduling fruit pulping for the production of fruit juices is of great importance in the beverage industry. Decisions have to be made regarding available processing time, the disposal of fruit that will not be pulped before stock loss due to spoilage, the fulfilment of customer demand and an optimal financial position. Sheduling depends on the capacity of the work force, pulping machine limitations and delivery deadlines. However, the situation is often encountered where the plant manager has to decide which fruit batches (usually from stock piles of overwhelming proportions during the harvesting season are to be pulped in order to minimize losses due to fruit deterioration. Such decisions are usually done manually, based on intuition and experience. A mathematical model is presented here which constructs a pulping strategy while minimising cascading financial losses associated with fruit grade drops within the stock pile. It is shown in particular that a minimisation of fruit losses is not a good criterion for optimality, and that substantial financial gains may be accomplished when minimising financial losses in stead of fruit losses, which is currently standard practice at most fruit pulping plants.

  8. Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration.

    Science.gov (United States)

    Keller, Laetitia; Offner, Damien; Schwinté, Pascale; Morand, David; Wagner, Quentin; Gros, Catherine; Bornert, Fabien; Bahi, Sophie; Musset, Anne-Marie; Benkirane-Jessel, Nadia; Fioretti, Florence

    2015-11-05

    The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be possible to achieve such complex regeneration. Indeed, three crucial steps are needed: the control of infection and inflammation and the regeneration of lost pulp tissues. For regenerative medicine, in particular for dental pulp regeneration, the use of nano-structured biomaterials becomes decisive. Nano-designed materials allow the concentration of many different functions in a small volume, the increase in the quality of targeting, as well as the control of cost and delivery of active molecules. Nanomaterials based on extracellular mimetic nanostructure and functionalized with multi-active therapeutics appear essential to reverse infection and inflammation and concomitantly to orchestrate pulp cell colonization and differentiation. This novel generation of nanomaterials seems very promising to meet the challenge of the complex dental pulp regeneration.

  9. Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Laetitia Keller

    2015-11-01

    Full Text Available The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be possible to achieve such complex regeneration. Indeed, three crucial steps are needed: the control of infection and inflammation and the regeneration of lost pulp tissues. For regenerative medicine, in particular for dental pulp regeneration, the use of nano-structured biomaterials becomes decisive. Nano-designed materials allow the concentration of many different functions in a small volume, the increase in the quality of targeting, as well as the control of cost and delivery of active molecules. Nanomaterials based on extracellular mimetic nanostructure and functionalized with multi-active therapeutics appear essential to reverse infection and inflammation and concomitantly to orchestrate pulp cell colonization and differentiation. This novel generation of nanomaterials seems very promising to meet the challenge of the complex dental pulp regeneration.

  10. Ionizing radiation and lipid peroxidation in human body

    International Nuclear Information System (INIS)

    Giubileo, Gianfranco

    1997-07-01

    Lipids are organic compounds constituting the living cells. Lipid molecules can be disassembled through peroxidative pathways and hydrocarbons can be bred as end-product of lipid peroxidation in vivo. Lipid peroxidation can be started by an indirect effect of ionizing radiation. So a radioinduced cellular damage in human body can be detected by monitoring the production of specific hydrocarbons

  11. Evolution of Lignocellulosic Macrocomponents in the Wastewater Streams of a Sulfite Pulp Mill: A Preliminary Biorefining Approach

    Directory of Open Access Journals (Sweden)

    Tamara Llano

    2015-01-01

    Full Text Available The evolution of lignin, five- and six-carbon sugars, and other decomposition products derived from hemicelluloses and cellulose was monitored in a sulfite pulp mill. The wastewater streams were characterized and the mass balances throughout digestion and total chlorine free bleaching stages were determined. Summative analysis in conjunction with pulp parameters highlights some process guidelines and valorization alternatives towards the transformation of the traditional factory into a lignocellulosic biorefinery. The results showed a good separation of cellulose (99.64% during wood digestion, with 87.23% of hemicellulose and 98.47% lignin dissolved into the waste streams. The following steps should be carried out to increase the sugar content into the waste streams: (i optimization of the digestion conditions increasing hemicellulose depolymerization; (ii improvement of the ozonation and peroxide bleaching stages, avoiding deconstruction of the cellulose chains but maintaining impurity removal; (iii fractionation of the waste water streams, separating sugars from the rest of toxic inhibitors for 2nd generation biofuel production. A total of 0.173 L of second-generation ethanol can be obtained in the spent liquor per gram of dry wood. The proposed methodology can be usefully incorporated into other related industrial sectors.

  12. Water requirements of the pulp and paper industry

    Science.gov (United States)

    Mussey, Orville D.

    1955-01-01

    Water, of varied qualities, is used for several purposes in the manufacture of pulp and paper, as a vehicle for transporting the constituents of paper in the paper machines; as process water for cooking wood chips to make pulp; as a medium for heat transfer; and for washing the pulpwood, the woodpulp, and the machines that handle the pulp. About 3,200 million gallons of water was withdrawn from surface- and ground-water sources each day during 1950 for the use of the pulp and paper industry. This is about 4 percent of the total estimated industrial withdrawal of water in the Nation The paper industry in the United States has been growing at a rapid rate. It has increased about tenfold in the last 50 years and has doubled every 15 years. The 1950 production of paper was about 24 million tons, which amounts to about 85 percent of the domestic consumption. In 1950, the pulp mills of the country produced more than 14 million tons of woodpulp, which supplied about 85 percent of the demand by the paper mills and other industries. The remainder of the fiber for paper manufacture was obtained from imported woodpulp, from reclaimed wastepaper, and from other fibers including rags and straw. The nationwide paper consumption for 1955 has been estimated at 31,700,000 tons. Woodpulp is classified according to the process by which it is made. Every woodpulp has characteristics that are carried over into the many and diverse grades of paper. Groundwood pulp is manufactured by simply grinding up wood and refining the resulting product. Soda, sulfite, and sulfate pulps are manufactured by chemically breaking down the lignin that cements the cellulose of the wood together and removing, cleaning, and sometimes bleaching the resulting fibers. Some woodpulp is produced by other methods. Sulfate-pulp mills are increasing in number and in rated daily capacity and are manufacturing more than half of the present domestic production of woodpulp. Most of the newer and larger woodpulp mills

  13. Potential for free radical-induced lipid peroxidation as a cause of endothelial cell injury in Rocky Mountain spotted fever.

    Science.gov (United States)

    Silverman, D J; Santucci, L A

    1988-01-01

    Cells infected by Rickettsia rickettsii, the causative agent of Rocky Mountain spotted fever, display unusual intracellular morphological changes characterized by dilatation of the membranes of the endoplasmic reticulum and outer nuclear envelope. These changes are consistent with those that might be expected to occur following peroxidation of membrane lipids initiated by oxygen radical species, such as the hydroxyl radical or a variety of organic radicals. Using a fluorescent probe, we have found significantly increased levels of peroxides in human endothelial cells infected by R. rickettsii. Studies with desferrioxamine, an iron chelator effective in preventing formation of the hydroxyl radical from hydrogen peroxide and the superoxide free radical, reduced peroxide levels in infected cells to those found in uninfected cells. This observation suggests that the increased peroxides in infected cells may be lipid peroxides, degradation products of free radical attack on polyenoic fatty acids. The potential for lipid peroxidation as an important mechanism in endothelial cell injury caused by R. rickettsii is discussed. Images PMID:3141280

  14. Modified silk fibroin scaffolds with collagen/decellularized pulp for bone tissue engineering in cleft palate: Morphological structures and biofunctionalities

    International Nuclear Information System (INIS)

    Sangkert, Supaporn; Meesane, Jirut; Kamonmattayakul, Suttatip; Chai, Wen Lin

    2016-01-01

    Cleft palate is a congenital malformation that generates a maxillofacial bone defect around the mouth area. The creation of performance scaffolds for bone tissue engineering in cleft palate is an issue that was proposed in this research. Because of its good biocompatibility, high stability, and non-toxicity, silk fibroin was selected as the scaffold of choice in this research. Silk fibroin scaffolds were prepared by freeze-drying before immerging in a solution of collagen, decellularized pulp, and collagen/decellularized pulp. Then, the immersed scaffolds were freeze-dried. Structural organization in solution was observed by Atomic Force Microscope (AFM). The molecular organization of the solutions and crystal structure of the scaffolds were characterized by Fourier transform infrared (FT-IR) and X-ray diffraction (XRD), respectively. The weight increase of the modified scaffolds and the pore size were determined. The morphology was observed by a scanning electron microscope (SEM). Mechanical properties were tested. Biofunctionalities were considered by seeding osteoblasts in silk fibroin scaffolds before analysis of the cell proliferation, viability, total protein assay, and histological analysis. The results demonstrated that dendrite structure of the fibrils occurred in those solutions. Molecular organization of the components in solution arranged themselves into an irregular structure. The fibrils were deposited in the pores of the modified silk fibroin scaffolds. The modified scaffolds showed a beta-sheet structure. The morphological structure affected the mechanical properties of the silk fibroin scaffolds with and without modification. Following assessment of the biofunctionalities, the modified silk fibroin scaffolds could induce cell proliferation, viability, and total protein particularly in modified silk fibroin with collagen/decellularized pulp. Furthermore, the histological analysis indicated that the cells could adhere in modified silk fibroin

  15. Comparative evaluation of the medicinal activities of methanolic extract of seeds, fruit pulps and fresh juice of Syzygium cumini in vitro

    Directory of Open Access Journals (Sweden)

    Repon Kumer Saha

    2013-11-01

    Full Text Available Objective: To establish the health benefits of Syzgium cumin to discover functional components present in the seeds, fruit pulps and fresh juice of this fruit grown in Bangladesh. Methods: Thin layer chromatography and ultra-violet spectroscopy were used to detect the presence of various types of compound in seeds and juice. Antioxidant effects were measured by DPPH scavenging assay and total reducing assay. Receptor binding activities was performed by hemagglutination inhibition assay. Anti-inflammatory assay and hydrogen peroxide induced hemolysis assay was also investigated. Disc diffusion assay was performed to show the antibacterial effect using Gram positive, Gram negative strains of bacteria and fungi. Results: Methanolic extract of the seeds showed stronger antioxidant, hydrogen peroxide induced hemolysis activities, hemagglutination inhibition activities and membrane stabilization activities than those of fresh juice. However, fresh juice showed stronger antibacterial and antifungal activities than those of methanolic seed extract. The seed contains higher amount of polyphenols and flavanoids than those of fruit juice. Conclusions: Therefore, fruit juice, fruit pulp and seed of Syzygium cumini contain medicinal active components in different ratios.

  16. The Kraft Pulp And Paper Properties of Sweet Sorghum Bagasse (Sorghum bicolor L Moench

    Directory of Open Access Journals (Sweden)

    Widya Fatriasari

    2015-05-01

    Full Text Available This study investigated the potency of sweet sorghum (Sorghum bicolor bagasse as raw material for pulp and paper using kraft pulping. The effects of alkali and sulfidity loading on kraft pulp and paper properties were also investigated. The pulping condition of the kraft pulp consisted of three levels of alkali loading (17, 19 and 22% and sulfidity loading (20, 22 and 24%. The maximum cooking temperature was 170°C for 4 h with a liquid to wood ratio of 10:1. Kraft pulping of this Numbu bagasse produced good pulp indicated by high screen yield and delignification selectivity with a low Kappa number (< 10. The unbleached pulp sheet produced a superior brightness level and a high burst index. The increase of active alkali loading tended to produce a negative effect on the pulp yield, Kappa number and paper sheet properties. Therefore, it is suggested to use a lower active alkaline concentration.

  17. Intestinal glutathione: determinant of mucosal peroxide transport, metabolism, and oxidative susceptibility

    International Nuclear Information System (INIS)

    Aw, Tak Yee

    2005-01-01

    The intestine is a primary site of nutrient absorption and a critical defense barrier against dietary-derived mutagens, carcinogens, and oxidants. Accumulation of oxidants like peroxidized lipids in the gut lumen can contribute to impairment of mucosal metabolic pathways, enterocyte dysfunction independent of cell injury, and development of gut pathologies, such as inflammation and cancer. Despite this recognition, we know little of the pathways of intestinal transport, metabolism, and luminal disposition of dietary peroxides in vivo or of the underlying mechanisms of lipid peroxide-induced genesis of intestinal disease processes. This chapter summarizes our current understanding of the determinants of intestinal absorption and metabolism of peroxidized lipids. I will review experimental evidence from our laboratory and others (Table 1) supporting the pivotal role that glutathione (GSH) and reduced nicotinamide adenine dinucleotide phosphate (NADPH) play in mucosal transport and metabolism of lipid hydroperoxides and how reductant availability can be compromised under chronic stress such as hypoxia, and the influence of GSH on oxidative susceptibility, and redox contribution to genesis of gut disorders. The discussion is pertinent to understanding dietary lipid peroxides and GSH redox balance in intestinal physiology and pathophysiology and the significance of luminal GSH in preserving the integrity of the intestinal epithelium

  18. Hydrogen peroxide and polyamines act as double edged swords in plant abiotic stress responses

    Directory of Open Access Journals (Sweden)

    Kamala Gupta

    2016-09-01

    Full Text Available The specific genetic changes through which plants adapt to the multitude of environmental stresses are possible because of the molecular regulations in the system. These intricate regulatory mechanisms once unveiled will surely raise interesting questions. Polyamines and hydrogen peroxide have been suggested to be important signalling molecules during biotic and abiotic stresses. Hydrogen peroxide plays a versatile role from orchestrating physiological processes to stress response. It helps to achieve acclimatization and tolerance to stress by coordinating intra-cellular and systemic signalling systems. Polyamines, on the other hand, are low molecular weight polycationic aliphatic amines, which have been implicated in various stress responses. It is quite interesting to note that both hydrogen peroxide and polyamines have a fine line of inter-relation between them since the catabolic pathways of the latter releases hydrogen peroxide. In this review we have tried to illustrate the roles and their multifaceted functions of these two important signalling molecules based on current literature. This review also highlights the fact that over accumulation of hydrogen peroxide and polyamines can be detrimental for plant cells leading to toxicity and pre-mature cell death.

  19. Hydrogen Peroxide and Polyamines Act as Double Edged Swords in Plant Abiotic Stress Responses.

    Science.gov (United States)

    Gupta, Kamala; Sengupta, Atreyee; Chakraborty, Mayukh; Gupta, Bhaskar

    2016-01-01

    The specific genetic changes through which plants adapt to the multitude of environmental stresses are possible because of the molecular regulations in the system. These intricate regulatory mechanisms once unveiled will surely raise interesting questions. Polyamines and hydrogen peroxide have been suggested to be important signaling molecules during biotic and abiotic stresses. Hydrogen peroxide plays a versatile role from orchestrating physiological processes to stress response. It helps to achieve acclimatization and tolerance to stress by coordinating intra-cellular and systemic signaling systems. Polyamines, on the other hand, are low molecular weight polycationic aliphatic amines, which have been implicated in various stress responses. It is quite interesting to note that both hydrogen peroxide and polyamines have a fine line of inter-relation between them since the catabolic pathways of the latter releases hydrogen peroxide. In this review we have tried to illustrate the roles and their multifaceted functions of these two important signaling molecules based on current literature. This review also highlights the fact that over accumulation of hydrogen peroxide and polyamines can be detrimental for plant cells leading to toxicity and pre-mature cell death.

  20. The hydrogen peroxide impact on larval settlement and metamorphosis of abalone Haliotis diversicolor supertexta

    Science.gov (United States)

    Zhang, Xiangjing; Yang, Zhihui; Cai, Zhonghua

    2008-08-01

    Abalone Haliotis diversicolor supertexta is an important economic mollusk. The settlement and metamorphosis are two critical stages during its development period, which has direct influence on abalone survival and production. The influence of reactive oxygen species (hydrogen peroxide) on abalone embryo and juvenile development were examined in this study. Larvae of Haliotis diversicolor supertexta were induced to settlement and metamorphose by exposure to seawater supplemented with hydrogen peroxide. They had the best performance at 800 μmol/L. The concentration of 1 000 μmol/L or higher was toxic to the larvae, as the larvae could settle down only at benthic diatom plates without complete metamorphosis. In addition, H2O2 adding time was critical to the larval performance. 24h after two-day post-fertilization was proved to be the optimal adding time. In this paper, two action mechanisms of hydrogen peroxide are discussed: (1) hydrogen peroxide has direct toxicity to ciliated cells, thus cause apoptosis; (2) hydrogen peroxide, as a product from catecholamines’ autoxidation process in vivo, can reverse this process to produce neuro-transmitters to induce abalone metamorphosis.

  1. The study of hydrogen peroxide level under cisplatin action using genetically encoded sensor hyper

    Science.gov (United States)

    Belova, A. S.; Orlova, A. G.; Maslennikova, A. V.; Brilkina, A. A.; Balalaeva, I. V.; Antonova, N. O.; Mishina, N. M.; Shakhova, N. M.; Belousov, V. V.

    2014-03-01

    The aim of the work was to study the participation of hydrogen peroxide in reaction of cervical cancer cell line HeLa Kyoto on cisplatin action. Determination of hydrogen peroxide level was performed using genetically encoded fluorescent sensor HyPer2. The dependence of cell viability on cisplatin concentration was determined using MTT assay. Mechanisms of cell death as well as HyPer2 reaction was revealed by flow cytometry after 6-hours of incubation with cisplatin in different concentrations. Cisplatin used in low concentrations had no effect on hydrogen peroxide level in HeLa Kyoto cells. Increase of HyPer2 fluorescence was detected only after exposure with cisplatin in high concentration. The reaction was not the consequence of cell death.

  2. Repair Responses of Dental Pulp to Tooth Injury and Biological Properties of Dentin-pulp Complex

    OpenAIRE

    大島, 勇人; Ohshima, Hayato

    2004-01-01

    Regeneration-the creation of a new tissue after the original one has been lost-is the fundamental biological capability in an organism. Numerous organs are considered to contain stem cells referred to as adult stem cells, even in the adult. Adult stem cells can give rise to a limited set of adult tissue types. In the field of clinical dentistry, it is well-known that the dentin-pulp complex is capable of repair after tooth injuries such as tooth replantation/transplantation or restorative pro...

  3. Pulp tissue inflammation and angiogenesis after pulp capping with transforming growth factor β1

    Directory of Open Access Journals (Sweden)

    Sri Kunarti

    2008-06-01

    Full Text Available In Restorative dentistry the opportunity to develop biomemitic approaches has been signalled by the possible use of various biological macromolecules in direct pulp capping reparation. The presence of growth factors in dentin matrix and the putative role indicating odontoblast differentiation during embryogenesis has led to the examination on the effect of endogenous TGF-β1. TGF-β1 is one of the Growth Factors that plays an important role in pulp healing. The application of exogenous TGF-β1 in direct pulp capping treatment should be experimented in fibroblast tissue in-vivo to see the responses of inflammatory cells and development of new blood vessels. The increase in food supplies always occurs in the process of inflammation therefore the development of angiogenesis is required to fulfil the requirement. This in-vivo study done on orthodontic patients indicated for premolar extraction between 10–15 years of age. A class V cavity preparation was created in the buccal aspect 1 mm above gingival margin to pulp exposure. The cavity was slowly irrigated with saline solution and dried using a sterile small cotton pellet. The sterile absorbable collagen membrane was applied and soaked in 5 ml TGF-β1. It was covered by a Teflon pledge to separate from Glass Ionomer Cement restoration. Evaluation was performed on day 7; 14; and 21. All samples were histopathologycally examined and data was statistically analysed using one way ANOVA and Dunnet T3.There were no inflammatory symptoms in clinical examination on both Ca(OH2 and TGF-β1, but they increased the infiltration of inflammatory cells on histopathological examination. There were no significant differences (p > 0.05 between Ca(OH2 and TGF-β1 in inflammation cell and significant differences (p < 0.05 in angiogenesis on day 7 and 14. There were no significant differences (p > 0.05 in inflammation cell with in TGF-β1 groups and significant differences (p < 0.05 with in Ca(OH2 groups on day 7

  4. Dry Kraft Pulping at Ambient Pressure for Cost Effective Energy Saving and Pollution Deduction

    Energy Technology Data Exchange (ETDEWEB)

    Yulin Deng; Art Ragauskas

    2012-08-28

    Sponsored by the DOE Industrial Energy Efficiency Grand Challenge program, our research team at the Georgia Institute of Technology conducted laboratory studies and confirmed the concept of making wood pulp using a dry pulping technology. This technology is a new process different from any prior pulping technology used in Kraft and CTMP pulping. Three different kinds of dry pulping methods were investigated. (a) Dry Pulping at Atmospheric Pressure: The first one is to dry and bake the pretreated woodchips in a conventional oven at atmospheric pressure without the use of a catalyst. (b) Dry Pulping at Reduced Pressure: The second method is to dry the pretreated woodchips first in a vacuum oven in the presence of anthraquinone (AQ) as a pulping catalyst, followed by baking at elevated temperature. (c) Liquid Free Chemical Pulping, LFCP. The third method is to first remove the free water of pretreated woodchips, followed by dry pulping using a conventional Kraft pulping digester with AQ and triton as additives. Method one: Experimental results indicated that Dry Pulping at Atmospheric Pressure could produce pulp with higher brightness and lower bulk than conventional Kraft pulp. However, tensile strength of the acquired pulp is much lower than traditional Kraft pulp, and their Kappa number and energy consumption are higher than conventional Kraft pulp. By fully analyzing the results, we concluded that wood fibers might be damaged during the drying process at elevated temperature. The main reason for wood fiber damage is that a long drying time was used during evaporation of water from the woodchips. This resulted in an un-uniform reaction condition on the woodchips: the outside layer of the woodchips was over reacted while inside the woodchips did not reacted at all. To solve this problem, dry pulping at reduced pressure was investigated. Method two: To achieve uniform reaction throughout the entire reaction system, the water inside the pretreated woodchips was

  5. Crystal structure of rubidium peroxide ammonia disolvate

    Directory of Open Access Journals (Sweden)

    Tobias Grassl

    2017-02-01

    Full Text Available The title compound, Rb2O2·2NH3, has been obtained as a reaction product of rubidium metal dissolved in liquid ammonia and glucuronic acid. As a result of the low-temperature crystallization, a disolvate was formed. To our knowledge, only one other solvate of an alkali metal peroxide is known: Na2O2·8H2O has been reported by Grehl et al. [Acta Cryst. (1995, C51, 1038–1040]. We determined the peroxide bond length to be 1.530 (11 Å, which is in accordance with the length reported by Bremm & Jansen [Z. Anorg. Allg. Chem. (1992, 610, 64–66]. One of the ammonia solvate molecules is disordered relative to a mirror plane, with 0.5 occupancy for the corresponding nitrogen atom.

  6. Functionalized Palladium Nanoparticles for Hydrogen Peroxide Biosensor

    Directory of Open Access Journals (Sweden)

    H. Baccar

    2011-01-01

    Full Text Available We present a comparison between two biosensors for hydrogen peroxide (H2O2 detection. The first biosensor was developed by the immobilization of Horseradish Peroxidase (HRP enzyme on thiol-modified gold electrode. The second biosensor was developed by the immobilization of cysteamine functionalizing palladium nanoparticles on modified gold surface. The amino groups can be activated with glutaraldehyde for horseradish peroxidase immobilization. The detection of hydrogen peroxide was successfully observed in PBS for both biosensors using the cyclic voltammetry and the chronoamperometry techniques. The results show that the limit detection depends on the large surface-to-volume ratio attained with palladium nanoparticles. The second biosensor presents a better detection limit of 7.5 μM in comparison with the first one which is equal to 75 μM.

  7. Innovations in papermaking: An LCA of printing and writing paper from conventional and high yield pulp

    International Nuclear Information System (INIS)

    Manda, B.M. Krishna; Blok, Kornelis; Patel, Martin K.

    2012-01-01

    Pulp and paper industry is facing challenges such as resource scarcity and greenhouse gas (GHG) emissions. The objective of this research is to investigate whether the use of new coatings (micro or nano TiO 2 ) and different pulp types could bring savings in wood, energy, GHG emissions and other environmental impacts in comparison with conventional printing and writing paper. We studied three types of pulp, namely i) unbleached virgin kraft pulp, ii) recovered fiber, and iii) high yield virgin chemithermo-mechanical pulp (CTMP). A life cycle assessment (LCA) was conducted from cradle to grave. Applying attributional modeling, we found that wood savings amount to 60% for the nanoparticle coated recovered fiber paper and 35% for the micro TiO 2 coated CTMP paper. According to the ReCiPe single score impact assessment method, the new product configurations allow the reduction of the environmental impacts by 10–35% compared to conventional kraft paper. Applying consequential modeling, we found larger energy and GHG emission savings compared to attributional modeling because the saved wood is used for producing energy, thereby replacing fossil fuels. The nanoparticle coated recovered fiber paper offered savings of non-renewable energy use (NREU) by 100% (13 GJ/ton paper) and GHG emission reduction by 75% (0.6 ton CO 2 eq./ton paper). Micro TiO 2 coated CTMP paper offered NREU savings by 25% (3 GJ/ton paper) and savings of GHG emissions by 10% (0.1 ton CO 2 eq./ton paper). The taking into account of all environmental impacts with the ReCiPe single score method leads to comparable results as that of attributional modeling. We conclude that the nanoparticle coated recovered fiber paper offered the highest savings and lowest environmental impacts. However, human toxicity and ecotoxicity impacts of the nanoparticles were not included in this analysis and need further research. If this leads to the conclusion that the toxicity impacts of the nanoparticles are serious, then

  8. Understanding about the classification of pulp inflammation

    Directory of Open Access Journals (Sweden)

    Trijoedani Widodo

    2007-03-01

    Full Text Available Since most authors use the reversible pulpitis and irreversible pulpitis classification, however, many dentists still do not implement these new classifications. Research was made using a descriptive method by proposing questionnaire to dentists from various dental clinics. The numbers of the dentists participating in this research are 22 dentists. All respondents use the diagnosis sheet during their examinations on patients. Nonetheless, it can't be known what diagnosis card used and most of the dentists are still using the old classification. Concerning responses given towards the new classification: a the new classification had been heard, however, it was not clear (36.3%; b the new classification has never been heard at all (63.6%. Then, responses concerning whether a new development is important to be followed-up or not: a there are those who think that information concerning new development is very important (27.2%; b those who feel that it is important to have new information (68.3%; c those who think that new information is not important (8%. It concluded that information concerning the development of classification of pulp inflammation did not reach the dentists.

  9. Bacterial infections of pulp and periodontal origin.

    Science.gov (United States)

    González-Moles, Miguel Angel; González, Nabila M

    2004-01-01

    The anatomical and structural characteristics of the pulp make this structure prone to altering as a result of, for instance, periodontal conditions (proximity), iatrogenic alterations, infections and involvement of vascular and nerve structures (it is surrounded by hard tissues that prevent expansion), to name just a few. Pulpitis is a process that courses with pain of varying intensity that allows us to determine the location of the lesion in clinical terms. Its evolution varies and may even progress to pulpar necrosis that in turn, produces neuritis-like pain. Diagnosis is established by means of clinical symptomatology and supported by X-rays, palpation of tissues at painful sites, application of electrical stimuli, heat, etc. Periodontitis is a bacterial infection originating in the apex. The most important form is the so-called acute apical periodontitis that arises as a result of a prior episode of pulpitis. It is characterized by acute pain located in the tooth, accompanied by the feeling of having a long-tooth. The patient refers being unable to chew on that side; there may be painful mobility of the tooth and an outflow of pus that alleviates symptoms. X-rays do not provide a lot of information, but may attest to a widening of the apical space. This pathology may disseminate to surrounding tissues, leading to conditions of considerable severity.

  10. Prospect of trema orientalis as a pulping raw material in bangladesh

    International Nuclear Information System (INIS)

    Jahan, M.S.

    2013-01-01

    The pulp and paper industry in Bangladesh is looking for new raw materials with high productivity per hectare. Currently, bamboo and Gmelina arborea are the main pulping raw materials for the pulp and paper industry of the country. Trema orientalis is one of the fastest growing woods in the tropical region. This paper reviews the literature on the topic, in particular, related to the chemical, morphological and physical properties of T. orientalis and its suitability for pulping. In addition, the advantages and disadvantages of various ulping processes proposed in the literature were critically analyzed. It was concluded that T. orientalis is a potential pulp wood for the Bangladesh pulp and paper industry. (author)

  11. Research on Wheat Straw Pulping with Ionic Liquid 1-Ethyl-3-Methylimidazole Bromide

    Directory of Open Access Journals (Sweden)

    Wei Song

    2016-12-01

    Full Text Available In this paper, the pulping process of wheat straw using ionic liquid 1-ethyl-3-methylimidazolium bromide ([Emim]Br as the digestion liquor is presented. The influence of pulping conditions on the pulp yield are analysed by single-factor and orthogonal experiments, and optimum pulping conditions are obtained. The average pulp yield reaches 44 %, and the average recovery rate of ionic liquid is 93.5 %. The XRD pattern shows no obvious change in the crystal structure of the wheat straw cellulose. Additionally, the SEM image illustrates that there are many fine fibres in the pulp and the spaces between the fibres are large.

  12. Cynara cardunculus L. alkaline pulps: alternatives fibres for paper and paperboard production.

    Science.gov (United States)

    Abrantes, S; Amaral, M E; Costa, A P; Duarte, A P

    2007-11-01

    The pulping of Cynara cardunculus L. (cardoon) was performed under conditions for kraft, kraft-AQ and soda-AQ processes. The best results in terms of delignification degree, expressed as kappa number, pulp viscosity and screened yield, were obtained for the kraft-AQ process with 0.20% of anthraquinone (AQ). The papermaking potential of the selected pulp was studied attending to biometric fibre characterisation, refining aptitude, optical and strength properties. All properties were compared against a Eucalyptus globulus pulp at different refining degrees. The cardoon pulp was also evaluated concerning its potential to board manufacture, alone and in mixtures with pine pulp, giving rise to promising results for liner manufacture.

  13. The effects of wood storage on the chemical composition and indigenous microflora of eucalyptus species used in the pulping industry

    CSIR Research Space (South Africa)

    Ramnath, L

    2018-02-01

    Full Text Available Lipophilic extractives naturally occurring in wood tend to coalesce during pulping to form pitch deposits, which have particularly undesirable effects on the pulping process and quality of pulp produced. A chemical characterization of different...

  14. Scaffold-free Prevascularized Microtissue Spheroids for Pulp Regeneration.

    Science.gov (United States)

    Dissanayaka, W L; Zhu, L; Hargreaves, K M; Jin, L; Zhang, C

    2014-12-01

    Creating an optimal microenvironment that mimics the extracellular matrix (ECM) of natural pulp and securing an adequate blood supply for the survival of cell transplants are major hurdles that need to be overcome in dental pulp regeneration. However, many currently available scaffolds fail to mimic essential functions of natural ECM. The present study investigated a novel approach involving the use of scaffold-free microtissue spheroids of dental pulp stem cells (DPSCs) prevascularized by human umbilical vein endothelial cells (HUVECs) in pulp regeneration. In vitro-fabricated microtissue spheroids were inserted into the canal space of tooth-root slices and were implanted subcutaneously into immunodeficient mice. Histological examination revealed that, after four-week implantation, tooth-root slices containing microtissue spheroids resulted in well-vascularized and cellular pulp-like tissues, compared with empty tooth-root slices, which were filled with only subcutaneous fat tissue. Immunohistochemical staining indicated that the tissue found in the tooth-root slices was of human origin, as characterized by the expression of human mitochondria, and contained odontoblast-like cells organized along the dentin, as assessed by immunostaining for nestin and dentin sialoprotein (DSP). Vascular structures formed by HUVECs in vitro were successfully anastomosed with the host vasculature upon transplantation in vivo, as shown by immunostaining for human CD31. Collectively, these findings demonstrate that prevascularized, scaffold-free, microtissue spheroids can successfully regenerate vascular dental pulp-like tissue and also highlight the significance of the microtissue microenvironment as an optimal environment for successful pulp-regeneration strategies. © International & American Associations for Dental Research.

  15. Yield Improvement and Energy Savings Uing Phosphonates as Additives in Kraft pulping

    Energy Technology Data Exchange (ETDEWEB)

    Ulrike W. Tschirner; Timothy Smith

    2007-03-31

    Project Objective: Develop a commercially viable modification to the Kraft process resulting in energy savings, increased yield and improved bleachability. Evaluate the feasibility of this technology across a spectrum of wood species used in North America. Develop detailed fundamental understanding of the mechanism by which phosphonates improve KAPPA number and yield. Evaluate the North American market potential for the use of phosphonates in the Kraft pulping process. Examine determinants of customer perceived value and explore organizational and operational factors influencing attitudes and behaviors. Provide an economic feasibility assessment for the supply chain, both suppliers (chemical supply companies) and buyers (Kraft mills). Provide background to most effectively transfer this new technology to commercial mills.

  16. Studies on the influence of structurally different peroxides in polypropylene/ethylene alpha olefin thermoplastic vulcanizates (TPVs

    Directory of Open Access Journals (Sweden)

    2008-03-01

    Full Text Available Novel thermoplastic vulcanizates (TPVs based on polypropylene (PP and new generation ethylene-octene copolymer (EOC have been developed by dynamic vulcanization process, which involves melt-mixing and simultaneously crosslinking a rubber with a thermoplastic. In this paper technologically compatibilized blends of PP and EOC were dynamically vulcanized by coagent assisted peroxide crosslinking system. The effect of structurally different types of peroxides, namely dicumyl peroxide, di-tert butyl peroxy isopropyl benzene and tert-butyl cumyl peroxide with varying concentrations on the properties on TPVs was mainly studied. The physico-mechanical, thermal and morphological properties of these TPVs were characterized by using X-ray diffraction (XRD, differential scanning calorimeter (DSC and scanning electron microscopy (SEM.

  17. Nano-hydroxyapatite and calcium-enriched mixture for pulp capping of sound primary teeth: a randomized clinical trial.

    Science.gov (United States)

    Haghgoo, Roza; Asgary, Saeed; Mashhadi Abbas, Fatemeh; Montazeri Hedeshi, Roshanak

    2015-01-01

    Nano-hydroxyapatite (NHA) has been used for regeneration of osseous defects. Calcium-enriched mixture (CEM) cement is also used for various dental treatments. This trial compared the efficacy of NHA and CEM cement for direct pulp capping (DPC) of sound primary teeth. In this randomized clinical trial with split-mouth design, after attaining informed consent, 20 sound primary canines scheduled for orthodontic extraction, were selected. After mechanical pulp exposure, the exposed site was capped with either NHA or CEM cement and then immediately restored with glass-ionomer and resin composite. The teeth were extracted after two months and examined histologically. Parameters of hard tissue bridge (HTB) formation, its type and quality as well as pulpal inflammation scores were compared between the two experimental groups. The data were analyzed using the Mann Whitney U and Fisher's exact test. The level of significance was set at 0.001. All CEM specimens showed inflammation score of 0 (less than 10%). However, in NHA group, inflammation scores of 0 (less than 10%), 1 (10%-30%) and 2 (30%-50%) were observed in 2 (20%), 4 (40%) and 4 (40%) specimens, respectively (P<0.001). HTB was formed in all CEM specimens while it was developed in 2 specimens of NHA (20%; P<0.001). All CEM specimens showed normal pulp; only two cases in NHA group (20%) demonstrated uninflamed normal pulp. CEM cement was superior to NHA as a DPC agent in terms of HTB formation and pulp inflammation scores. It is a suitable material for the DPC of primary teeth.

  18. Lipid Peroxidation and Antioxidant Status in Preeclampsia

    Directory of Open Access Journals (Sweden)

    Rokeya Begum

    2011-07-01

    Full Text Available Background: Preeclampsia is the most common and major medical complication of pregnancy with a high incidence of maternal and foetal morbidity and mortality. During pregnancy abnormally increased lipid peroxidation and free radical formation as well as significantly decreased antioxidants production in maternal blood may lead to pathogenesis of preeclampsia. So, we designed this study as little information is known about lipid peroxidation and antioxidant level in preeclampsia. Objectives: To assess the serum malondialdehyde (MDA level as a lipid peroxidation product and vitamin E (antioxidant level in women with preeclampsia as well as in normal pregnancy and to compare the values. Materials and Methods: The study was conducted on 60 women aged from 25 to 35 years in the department of Biochemistry, Budi Kemuliaan Maternity Hospital (BKMH in Jakarta during the period April to July 2004. Twenty were normal pregnant women and 20 were preeclamptic patients. For comparison age matched 20 apparently healthy nonpregnant women were included in the study. The study subjects were selected from outpatient department (OPD of Obstetrics and Gynaecology of BKMH in Jakarta. Serum MDA (lipid peroxidation product level was measured by thiobarbituric acid reactive substances assay (TBRAS method and vitamin E was estimated spectroflurometrically. Data were analyzed by unpaired Student’s t test between the groups by using SPSS version 12. Results: The mean serum MDA levels were significantly higher in normal pregnancy and also in preeclampsia than that of nonpregnant control group women (p<0.001. Again the serum MDA levels were significantly higher in preeclampsia than that of normal pregnant women (p<0.001. The serum vitamin E levels were significantly lower in preeclampsia and also in normal pregnancy than that of nonpregnant control women (p<0.001. Moreover, the serum vitamin E levels were significantly lower in preeclampsia compared to that of normal

  19. Mechanism of action of hydrogen peroxide in wheat thermotolerance

    African Journals Online (AJOL)

    With the increase in H2O2 accumulation, an increase in the number of isoenzymes of superoxide dismutase and catalase were observed with high activities under differential heat shock. A decrease in the proline accumulation was observed under differential heat shock. Exogenous application of H2O2 (10 mmole/L) leads ...

  20. Antioxidant activity of dietary fruits, vegetables, and commercial frozen fruit pulps.

    Science.gov (United States)

    Hassimotto, Neuza Mariko Aymoto; Genovese, Maria Inés; Lajolo, Franco Maria

    2005-04-20

    Fruits, vegetables, and commercial frozen pulps (FP) consumed in the Brazilian diet were analyzed for antioxidant activities using two different methods, one that determines the inhibition of copper-induced peroxidation of liposome and another based on the inhibition of the co-oxidation of linoleic acid and beta-carotene. The anthocyanin-rich samples showed the highest, concentration-dependent, antioxidant activities in both systems. In the liposome system, at both 10 and 50 microM gallic acid equivalent (GAE) addition levels, the neutral and acidic flavonoids of red cabbage, red lettuce, black bean, mulberry, Gala apple peel, jambolao, acai FP, mulberry FP, and the acidic flavonoids of acerola FP showed the highest antioxidant activities (>85% inhibition). In the beta-carotene bleaching system, the samples cited above plus red guava gave inhibition values >70%. On the other hand, some samples showed pro-oxidant activity in the liposome system coincident with a low antioxidant activity in the beta-carotene system. There was no relationship between total phenolics content, vitamin C, and antioxidant activity, suggesting that the antioxidant activity is a result of a combination of different compounds having synergic and antagonistic effects.

  1. Physicochemical and spectroscopical investigation of Pequi (Caryocar coriaceum Wittm.) pulp oil

    Energy Technology Data Exchange (ETDEWEB)

    Sena, D. M.; Rodrigues, F. F. G.; Freire, P. T. C.; Lima, S. D. de; Coutinho, H. D. M.; Carvajal, J. C. L.; Costa, J. G. M. da

    2010-07-01

    This work describes the physicochemical characterization of the fruit pulp oil of Caryocar coriaceum (Wittm), pequi. The chemical composition was assessed by GLC, which demonstrated the following fatty acid contents: oleic (55.79%), palmitic (34.18%), heptadecenoic (5.86%), linoleic (1.80%), stearic (1.73%), eicosenoic (0.37%) and palmitoleic (0.27%). The vibrational spectroscopy results were typical of an edible oil, and are in accordance with the high unsaturated fatty acid content. Physical properties such as water content, acidity, peroxide index, saponification index, relative density, viscosity and refraction index are reported for the first time for this species. Pequi fruits have a high nutritional value, and are rich in protein and vitamins. In addition, their composition includes essential fatty acids, which accounts for the popular use of the fruit oil for antioxidant and antiinflammatory activity. There is great interest in extending the use of this natural product by exploiting the combined social, economic and therapeutic values of its derivatives. (Author)

  2. Use of Coffee Pulp and Minerals for Natural Soil Ameliorant

    Directory of Open Access Journals (Sweden)

    Pujiyanto Pujiyanto

    2007-05-01

    Full Text Available In coffee plantation, solid waste of coffee pulp is usually collected as heap nearby processing facilities for several months prior being used as compost. The practice is leading to the formation of odor and liquid which contaminate the environment. Experiments to evaluate the effect of natural soil ameliorant derived from coffee pulp and minerals were conducted at The Indonesian Coffee and Cocoa Research Institute in Jember, East Java. The experiments were intended to optimize the use of coffee pulp to support farming sustainability and minimize negative impacts of solid waste disposal originated from coffee cherry processing. Prior to applications, coffee pulp was hulled to organic paste. The paste was then mixed with 10% minerals (b/b. Composition of the minerals was 50% zeolite and 50% rock phosphate powder. The ameliorant was characterized for their physical and chemical properties. Agronomic tests were conducted on coffee and cocoa seedling. The experiments were arranged according to Randomized Completely Design with 2 factors, consisted of natural ameliorant and inorganic fertilizer respectively. Natural ameliorant derived from coffee pulp was applied at 6 levels: 0, 30, 60, 90, 120 and 150 g dry ameliorant/seedling of 3 kg soil, equivalent to 0, 1, 2, 3, 4 and 5% (b/b of ameliorant respectively. Inorganic fertilizer was applied at 2 levels: 0 and 2 g fertilizer/application of N-P-K compound fertilizer of 15-15-15 respectively. The inorganic fertilizer was applied 4 times during nursery of coffee and cocoa. The result of the experiment indicated that coffee pulp may be used as natural soil ameliorant. Composition of ameliorant of 90% coffee pulp and 10% of minerals has good physical and chemical characteristics for soil amelioration. The composition has high water holding capacity; cations exchange capacity, organic carbon and phosphorus contents which are favorable to increase soil capacity to support plant growth. Application of

  3. Pollution control in pulp and paper industrial effluents using integrated chemical-biological treatment sequences.

    Science.gov (United States)

    El-Bestawy, Ebtesam; El-Sokkary, Ibrahim; Hussein, Hany; Keela, Alaa Farouk Abu

    2008-11-01

    The main objective of the present study was to improve the quality of pulp and paper industrial wastewater of two local mills RAKTA and El-Ahlia, Alexandria, Egypt, and to bring their pollutant contents to safe discharge levels. Quality improvement was carried out using integrated chemical and biological treatment approaches after their optimization. Chemical treatment (alum, lime, and ferric chloride) was followed by oxidation using hydrogen peroxide and finally biological treatment using activated sludge (90 min for RAKTA and 60 min for El-Ahlia effluents). Chemical coagulation produced low-quality effluents, while pH adjustment during coagulation treatment did not enhance the quality of the effluents. Maximum removal of the tested pollutants was achieved using the integrated treatment and the pollutants recorded residual concentrations (RCs) of 34.67, 17.33, 0.13, and 0.43 mg/l and 15.0, 11.0, 0.0, and 0.13 mg/l for chemical oxygen demand (COD), biochemical oxygen demand (BOD5), tannin and lignin, and silica in RAKTA and El-Ahlia effluents, respectively, all of which were below their maximum permissible limits (MPLs) for the safe discharge into water courses. Specific oxygen uptake rate (SOUR) and sludge volume index (SVI) values reflect good conditions and healthy activated sludge. Based on the previous results, optimized conditions were applied as bench scale on the raw effluents of RAKTA and El-Ahlia via the batch chemical and the biological treatment sequences proposed. For RAKTA effluents, the sequence was as follows: (1) coagulation with 375 mg/l FeCl3, (2) oxidation with 50 mg/l hydrogen peroxide, and (3) biological treatment using activated sludge with 2,000 mg/l initial concentration and 90 min hydraulic retention time (HRT), while for El-Ahlia raw effluents, the sequence was (1) coagulation with 250 mg/l FeCl3, (2) oxidation with 45 mg/l hydrogen peroxide, and (3) biological treatment using activated sludge with 2,000 mg/l initial concentration and 60

  4. Characterization of Cypress Wood for Kraft Pulp Production

    Directory of Open Access Journals (Sweden)

    António J. A. Santos

    2014-06-01

    Full Text Available Wood samples of Cupressus arizonica, C. lusitanica, and C. sempervirens were evaluated for chemical, anatomical, and pulp characteristics as raw material for pulp production. Two 17-year-old trees per species were harvested, and wood samples were taken at a height of 2 m. Wood chips from Pinus pinaster (Portugal and P. sylvestris (Finland were used as references. C. arizonica differed from C. lusitanica and C. sempervirens with significantly lower (p < 0.05 tracheid diameter and wall thickness in the earlywood. The total extractives contents were 3.9%, 3.3%, and 2.5% for C. lusitanica, C. sempervirens, and C. arizonica, respectively, lower than the 5.1% for P. pinaster and 4.5% for P. sylvestris. Klason lignin content ranged from 33.0 to 35.6%, higher than the 28.0 to 28.7% for the pinewoods. The kraft pulp yields for C. arizonica, C. lusitanica, and C. sempervirens were 37.7%, 36.7%, and 38.7%, respectively, with kappa numbers of 32.0, 31.6, and 28.7, respectively; the yield values were 40.8% and 42.8%, with kappa numbers of 23.4 and 21.0, for P. pinaster and P. sylvestris, respectively. The cypress species are clearly different from pine in relation to wood pulping behavior. Among the cypress, C. sempervirens provided the best pulping results.

  5. Paleoproteomics of the Dental Pulp: The plague paradigm.

    Science.gov (United States)

    Barbieri, Rémi; Mekni, Rania; Levasseur, Anthony; Chabrière, Eric; Signoli, Michel; Tzortzis, Stéfan; Aboudharam, Gérard; Drancourt, Michel

    2017-01-01

    Chemical decomposition and fragmentation may limit the detection of ancient host and microbial DNA while some proteins can be detected for extended periods of time. We applied paleoproteomics on 300-year-old dental pulp specimens recovered from 16 individuals in two archeological funeral sites in France, comprising one documented plague site and one documented plague-negative site. The dental pulp paleoproteome of the 16 teeth comprised 439 peptides representative of 30 proteins of human origin and 211 peptides representative of 27 proteins of non-human origin. Human proteins consisted of conjunctive tissue and blood proteins including IgA immunoglobulins. Four peptides were indicative of three presumable Yersinia pestis proteins detected in 3/8 dental pulp specimens from the plague-positive site but not in the eight dental pulp specimens collected in the plague-negative site. Paleoproteomics applied to the dental pulp is a new and innovative approach to screen ancient individuals for the detection of blood-borne pathogens and host inflammatory response.

  6. Mesta/Kenaf as raw material for Kraft pulping

    Energy Technology Data Exchange (ETDEWEB)

    Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

    1980-03-15

    In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

  7. Pulp tissue in sex determination: A fluorescent microscopic study

    Science.gov (United States)

    Nayar, Amit; Singh, Harkanwal Preet; Leekha, Swati

    2014-01-01

    Aims: To determine and compare the reliability of pulp tissue in determination of sex and to analyze whether caries have any effect on fluorescent body test. Materials and Methods: This study was carried on 50 maxillary and mandibular teeth (25 male teeth and 25 female teeth), which were indicated for extraction. The teeth are categorized into 5 groups, 10 each (5 from males and 5 from females) on the basis of caries progression. The pulp cells are stained with quinacrine hydrochloride and observed with fluorescent microscope for fluorescent body. Gender is determined by identification of Y chromosome fluorescence in dental pulp. Results: Fluorescent bodies were found to be more in sound teeth in males as the caries increase the mean percentage of fluorescent bodies observed decreases in males. We also observed the fluorescent spots in females, and the value of the spot increases in female as the caries progresses, thereby giving false positive results in females. Conclusion: Sex determination by fluorescent staining of the Y chromosome is a reliable technique in teeth with healthy pulps or caries with enamel or up to half way of dentin. Teeth with caries involving pulp cannot be used for sex determination. PMID:25125912

  8. Radiation modification of cellulose pulps. Preparation of cellulose derivatives

    International Nuclear Information System (INIS)

    Iller, E.; Zimek, Z.; Stupinska, H.; Mikolajczyk, W; Starostka, P.

    2005-01-01

    One of the most common methods of cellulose pulp modification (activation) applied in the production process of cellulose derivatives is the treatment of the pulp with NaOH solutions leading to the formation of alkalicellulose. The product then undergoes a prolonged process of maturation by its storage under specific conditions. The goal of the process is lowering of the molecular weight of cellulose down to the level resulting from various technological requirements. The process is time-consuming and costly; besides, it requires usage of large-capacity technological vessels and produces considerable amounts of liquid waste. Therefore, many attempts have been made to limit or altogether eliminate the highly disadvantageous stage of cellulose treatment with lye. One of the alternatives proposed so far is the radiation treatment of the cellulose pulp. In the pulp exposed to an electron beam, the bonds between molecules of D-antihydroglucopiranoses loosen and the local crystalline lattice becomes destroyed. This facilitates the access of chemical reagents to the inner structure of the cellulose and, in consequence, eliminates the need for the prolonged maturation of alkalicellulose, thus reducing the consumption of chemicals by the whole process. Research aimed at the application of radiation treatment of cellulose pulp for the production of cellulose derivatives has been conducted by a number of scientific institutions including the Institute of Nuclear Chemistry and Technology, Institute of Biopolymers and Chemical Fibres, and Pulp and Paper Research Institute. For the investigations and assessment of the molecular, hypermolecular, morphologic properties and the chemical reactivity, cellulose pulps used for chemical processing, namely Alicell, Borregaard and Ketchikan, as well as paper pulps made from pine and birch wood were selected. The selected cellulose pulps were exposed to an electron beam with an energy of 10 MeV generated in a linear electron accelerator

  9. Rice straw pulp obtained by using various methods.

    Science.gov (United States)

    Rodríguez, Alejandro; Moral, Ana; Serrano, Luis; Labidi, Jalel; Jiménez, Luis

    2008-05-01

    Rice straw was used as an alternative raw material to obtain cellulosics pulps. Pulping was done by using classics reagents as soda (with anthraquinone and parabenzoquinone as aditives), potassium hydroxide and Kraft process. The holocellulose, alpha-cellulose and lignin contents of rice straw (viz. 60.7, 41.2 and 21.9 wt%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using soda, soda and anthraquinone at 1 wt%, soda and parabenzoquinone at 1 wt%, potassium hydroxide and sodium sulphate (Kraft process) under two different sets of operating conditions, namely: (a) a 10 wt% reagent concentration, 170 degrees C and 60 min; and (b) 15 wt% reagent, 180 degrees C and 90 min. The solid/liquid ratio was 6 in both cases. Paper sheets made from pulp extracted by cooking with soda (15 wt%) and AQ (1 wt%) at 180 degrees C and 90 min pulp exhibit the best drainage index, breaking length, stretch and burst index (viz. 23 degrees SR, 3494 m, 3.34% and 2.51 kN/g, respectively).

  10. Characterization of active paper packaging incorporated with ginger pulp oleoresin

    Science.gov (United States)

    Wiastuti, T.; Khasanah, L. U.; Atmaka Kawiji, W.; Manuhara, G. J.; Utami, R.

    2016-02-01

    Utilization of ginger pulp waste from herbal medicine and instant drinks industry in Indonesia currently used for fertilizer and fuel, whereas the ginger pulp still contains high oleoresin. Active paper packaging were developed incorporated with ginger pulp oleoresin (0%, 2%, 4%, and 6% w/w). Physical (thickness, tensile strength, and folding endurance, moisture content), sensory characteristics and antimicrobial activity of the active paper were evaluated. Selected active paper then were chemically characterized (functional groups). The additional of ginger pulp oleoresin levels are reduced tensile strength, folding endurance and sensory characteristic (color, texture and overall) and increased antimicrobial activity. Due to physical, sensory characteristic and antimicrobial activity, active paper with 2% ginger pulp oleoresin incorporation was selected. Characteristics of selected paper were 9.93% of water content; 0.81 mm of thickness; 0.54 N / mm of tensile strength; 0.30 of folding endurance; 8.43 mm inhibits the growth of Pseudomonas fluorescence and 27.86 mm inhibits the growth of Aspergillus niger (antimicrobial activity) and neutral preference response for sensory properties. For chemical characteristic, selected paper had OH functional group of ginger in 3422.83 cm-1 of wave number and indicated contain red ginger active compounds.

  11. Secretoneurin and PE-11 immunoreactivity in the human dental pulp.

    Science.gov (United States)

    Steiner, René; Fischer-Colbrie, Reiner; Bletsa, Athanasia; Laimer, Johannes; Troger, Josef

    2018-02-01

    To explore whether there are differences in the concentration of the secretogranin II-derived peptide secretoneurin and the chromogranin B-derived peptide PE-11 between the healthy and inflamed human dental pulps. Furthermore, colocalization studies with calcitonin gene-related peptide were performed to confirm the sensory origin of the peptidergic nerves in the dental pulp. The concentrations of secretoneurin and PE-11 were determined by highly sensitive radioimmunoassays in extracts of dental pulps, the molecular form of secretoneurin immunoreactivities by RP-HPLC with subsequent radioimmunoassay and colocalization studies with calcitonin gene-related peptide were performed by double immunofluorescence. Only secretoneurin but not PE-11 was detectable by radioimmunoassays whereas nerve fibers could be made visible for both secretoneurin and PE-11. Furthermore, there was a full colocalization of secretoneurin and PE-11 with calcitonin gene-related peptide in immunohistochemical experiments. There were no differences in the concentration of secretoneurin between the healthy and inflamed human dental pulp and moreover, the characterization of the secretoneurin immunoreactivities revealed that only authentic secretoneurin was detected with the secretoneurin antibody. There is unequivocal evidence that secretoneurin and PE-11 are constituents of the sensory innervation of the human dental pulp and although not exclusively but are yet present in unmyelinated C-fibers which transmit predominantly nociceptive impulses. Secretoneurin might be involved in local effector functions as well, particularly in neurogenic inflammation, given that this is the case despite of unaltered levels in inflamed tissue. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Dentin and dental pulp regeneration by the patient's endogenous cells.

    Science.gov (United States)

    Kim, Sahng G; Zheng, Ying; Zhou, Jian; Chen, Mo; Embree, Mildred C; Song, Karen; Jiang, Nan; Mao, Jeremy J

    2013-03-01

    The goal of regenerative endodontics is to restore the functions of the dental pulp-dentin complex. Two approaches are being applied toward dental pulp-dentin regeneration: cell transplantation and cell homing. The majority of previous approaches are based on cell transplantation by delivering ex vivo cultivated cells toward dental pulp or dentin regeneration. Many hurdles limit the clinical translation of cell transplantation such as the difficulty of acquiring and isolating viable cells, uncertainty of what cells or what fractions of cells to use, excessive cost of cell manipulation and transportation, and the risk of immune rejection, pathogen transmission, and tumorigenesis in associated with ex vivo cell manipulation. In contrast, cell homing relies on induced chemotaxis of endogenous cells and therefore circumvents many of the difficulties that are associated with cell transplantation. An array of proteins, peptides, and chemical compounds that are yet to be identified may orchestrate endogenous cells to regenerate dental pulp-dentin complex. Both cell transplantation and cell homing are scientifically valid approaches; however, cell homing offers a number of advantages that are compatible with the development of clinical therapies for dental pulp-dentin regeneration.

  13. The annual frequency of root fillings, tooth extractions and pulp-related procedures in Danish adults during 1977-2003

    DEFF Research Database (Denmark)

    Bjørndal, L.; Reit, C.

    2004-01-01

    endodontic epidemiology, frequency of root fillings, pulp capping, stepwise excavation, tooth extractions......endodontic epidemiology, frequency of root fillings, pulp capping, stepwise excavation, tooth extractions...

  14. miRNA-720 controls stem cell phenotype, proliferation and differentiation of human dental pulp cells.

    Directory of Open Access Journals (Sweden)

    Emilio Satoshi Hara

    Full Text Available Dental pulp cells (DPCs are known to be enriched in stem/progenitor cells but not well characterized yet. Small non-coding microRNAs (miRNAs have been identified to control protein translation, mRNA stability and transcription, and have been reported to play important roles in stem cell biology, related to cell reprogramming, maintenance of stemness and regulation of cell differentiation. In order to characterize dental pulp stem/progenitor cells and its mechanism of differentiation, we herein sorted stem-cell-enriched side population (SP cells from human DPCs and periodontal ligament cells (PDLCs, and performed a locked nucleic acid (LNA-based miRNA array. As a result, miR-720 was highly expressed in the differentiated main population (MP cells compared to that in SP cells. In silico analysis and a reporter assay showed that miR-720 targets the stem cell marker NANOG, indicating that miR-720 could promote differentiation of dental pulp stem/progenitor cells by repressing NANOG. Indeed, gain-and loss-of-function analyses showed that miR-720 controls NANOG transcript and protein levels. Moreover, transfection of miR-720 significantly decreased the number of cells positive for the early stem cell marker SSEA-4. Concomitantly, mRNA levels of DNA methyltransferases (DNMTs, which are known to play crucial factors during stem cell differentiation, were also increased by miR-720 through unknown mechanism. Finally, miR-720 decreased DPC proliferation as determined by immunocytochemical analysis against ki-67, and promoted odontogenic differentiation as demonstrated by alizarin red staining, as well as alkaline phosphatase and osteopontin mRNA levels. Our findings identify miR-720 as a novel miRNA regulating the differentiation of DPCs.

  15. The prevalence and distribution of radiopaque, calcified pulp stones: A cone-beam computed tomography study in a northern Taiwanese population

    Directory of Open Access Journals (Sweden)

    Chen-Yu Hsieh

    2018-06-01

    Conclusion: Pulp stones are more frequent in maxillary teeth compared to mandibular teeth. Pulp stones in molar teeth were significantly more common than premolars and incisors. CBCT could be a sensitive tool to detect pulp stones, especially simplifying identification of pulp stones in radicular pulp. Knowledge of pulp stones distribution can aid dentists in clinical endodontic treatment.

  16. Wood Pulp Digetster Wall Corrosion Investigation

    Energy Technology Data Exchange (ETDEWEB)

    Giles, GE

    2003-09-18

    The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

  17. Ameliorating effects of genestein: Study on mice liver glutathione and lipid peroxidation after irradiation

    International Nuclear Information System (INIS)

    Gaur, A.

    2010-01-01

    Genistein is a soya isoflavone, which is found naturally in legumes. such as soybeans and chickpeas. Radiation-induced free radicals in turn impair the antioxidative defense mechanism, leading to an increased membrane lipid peroxidation that results in damage of the membrane bound enzyme and may lead to damage or death of cell. Hence, the lipid peroxidation is a good biomarker of damage occurs due to radiation and the inhibition of lipid peroxidation is suggestive of radioprotective action. Glutathione has been shown to protect cells against oxidative stress by reacting with peroxides and hydroperoxides and determines the inherent radiosensitivity of cells. Materials and Methods: For experimentation, healthy Swiss Albino male mice of 6-8 weeks old were selected from inbred colony. Genistein was dissolved in dimethyl sulfoxide and then prepared different concentration solutions so that the volume administered intraperitoneally was 0.5 ml. Lipid peroxidation was estimated by the method of Ohkawa and GSH was estimated by the method of Moron. Results: The intraperitoneal administration of optimum dose (200 mg/kg body weight) of Genistein before 24 hours and 15 minutes of irradiation (8 Gy at a dose rate of 1.02 Gy/min)reverted the increase in lipid peroxidation (by 18.01% ± 3.05) and decrease of Glutathione (by 62.05%±21.58) caused by irradiation in liver of Swiss albino mice. Statistically analyzed survival data produced a dose reduction factor = 1.24. Conclusion: The results indicate that Genistein against radiation effect may pave way to the formulation of medicine in radiotherapy for normal tissue and possible against radiomimetic drug induced toxicity.

  18. Application of thermoalkalophilic xylanase from Arthrobacter sp. MTCC 5214 in biobleaching of kraft pulp

    Digital Repository Service at National Institute of Oceanography (India)

    Khandeparker, R.; Bhosle, N.B.

    released by enzyme treatment showed a characteristic peak at 280 nm indicating the presence of lignin in the released coloring matter. Enzymatic prebleaching of kraft pulp showed 20 % reduction in kappa number of the pulp without much change in viscosity...

  19. Nutritional composition of Annona crassiflora pulp and acceptability of bakery products prepared with its flour

    Directory of Open Access Journals (Sweden)

    Paula Villela

    2013-09-01

    Full Text Available Annona crassiflora offers an edible fruit native to the Savanna. This study aimed to develop a flour meal from Annona crassiflora pulp; analyze the chemical composition of the fresh pulp and its flour; develop and verify the acceptance of formulations with different concentrations of the flour of Annona crassiflora pulp. Fruit used were selected and processed. The pulp was dried in an oven at 60-65 ºC/48h. We analyzed the chemical composition, and two formulations of breads were prepared with 10 and 20% Annona crassiflora pulp. The results showed that the drying of Annona crassiflora pulp enriched its nutritional value. The Annona crassiflora pulp showed important chemical components, as insoluble fibers (pulp and flour, minerals (potassium, calcium, manganese and others and antioxidant compounds. The formulations were well-accepted in a sensory point of view and proved to be a good alternative to the exploitation of the fruit.

  20. Hydrogen peroxide stabilization in one-dimensional flow columns

    Science.gov (United States)

    Schmidt, Jeremy T.; Ahmad, Mushtaque; Teel, Amy L.; Watts, Richard J.

    2011-09-01

    Rapid hydrogen peroxide decomposition is the primary limitation of catalyzed H 2O 2 propagations in situ chemical oxidation (CHP ISCO) remediation of the subsurface. Two stabilizers of hydrogen peroxide, citrate and phytate, were investigated for their effectiveness in one-dimensional columns of iron oxide-coated and manganese oxide-coated sand. Hydrogen peroxide (5%) with and without 25 mM citrate or phytate was applied to the columns and samples were collected at 8 ports spaced 13 cm apart. Citrate was not an effective stabilizer for hydrogen peroxide in iron-coated sand; however, phytate was highly effective, increasing hydrogen peroxide residuals two orders of magnitude over unstabilized hydrogen peroxide. Both citrate and phytate were effective stabilizers for manganese-coated sand, increasing hydrogen peroxide residuals by four-fold over unstabilized hydrogen peroxide. Phytate and citrate did not degrade and were not retarded in the sand columns; furthermore, the addition of the stabilizers increased column flow rates relative to unstabilized columns. These results demonstrate that citrate and phytate are effective stabilizers of hydrogen peroxide under the dynamic conditions of one-dimensional columns, and suggest that citrate and phytate can be added to hydrogen peroxide before injection to the subsurface as an effective means for increasing the radius of influence of CHP ISCO.

  1. Using Apparent Density of Paper from Hardwood Kraft Pulps to Predict Sheet Properties, based on Unsupervised Classification and Multivariable Regression Techniques

    Directory of Open Access Journals (Sweden)

    Ofélia Anjos

    2015-07-01

    Full Text Available Paper properties determine the product application potential and depend on the raw material, pulping conditions, and pulp refining. The aim of this study was to construct mathematical models that predict quantitative relations between the paper density and various mechanical and optical properties of the paper. A dataset of properties of paper handsheets produced with pulps of Acacia dealbata, Acacia melanoxylon, and Eucalyptus globulus beaten at 500, 2500, and 4500 revolutions was used. Unsupervised classification techniques were combined to assess the need to perform separated prediction models for each species, and multivariable regression techniques were used to establish such prediction models. It was possible to develop models with a high goodness of fit using paper density as the independent variable (or predictor for all variables except tear index and zero-span tensile strength, both dry and wet.

  2. Advanced Scaffolds for Dental Pulp and Periodontal Regeneration.

    Science.gov (United States)

    Bottino, Marco C; Pankajakshan, Divya; Nör, Jacques E

    2017-10-01

    No current therapy promotes root canal disinfection and regeneration of the pulp-dentin complex in cases of pulp necrosis. Antibiotic pastes used to eradicate canal infection negatively affect stem cell survival. Three-dimensional easy-to-fit antibiotic-eluting nanofibers, combined with injectable scaffolds, enriched or not with stem cells and/or growth factors, may increase the likelihood of achieving predictable dental pulp regeneration. Periodontitis is an aggressive disease that impairs the integrity of tooth-supporting structures and may lead to tooth loss. The latest advances in membrane biomodification to endow needed functionalities and technologies to engineer patient-specific membranes/constructs to amplify periodontal regeneration are presented. Copyright © 2017 Elsevier Inc. All rights reserved.

  3. Design of a Turbulence Generator of Medium Consistency Pulp Pumps

    Directory of Open Access Journals (Sweden)

    Hong Li

    2012-01-01

    Full Text Available The turbulence generator is a key component of medium consistency centrifugal pulp pumps, with functions to fluidize the medium consistency pulp and to separate gas from the liquid. Structure sizes of the generator affect the hydraulic performance. The radius and the blade laying angle are two important structural sizes of a turbulence generator. Starting with the research on the flow inside and shearing characteristics of the MC pulp, a simple mathematical model at the flow section of the shearing chamber is built, and the formula and procedure to calculate the radius of the turbulence generator are established. The blade laying angle is referenced from the turbine agitator which has the similar shape with the turbulence generator, and the CFD simulation is applied to study the different flow fields with different blade laying angles. Then the recommended blade laying angle of the turbulence generator is formed to be between 60° and 75°.

  4. Electron treatment of wood pulp for the viscose process

    Science.gov (United States)

    Stepanik, T. M.; Ewing, D. E.; Whitehouse, R.

    2000-03-01

    Electron processing is currently being evaluated by several viscose producers for integration into their process. The viscose industry converts dissolving wood pulp into products such as staple fibre, filament, cord, film, packaging, and non-edible sausage casings. These materials are used in the clothing, drapery, hygiene, automobile, food, and packaging industries. Viscose producers are facing increasingly high production costs and stringent environmental regulations that have forced some plants to close. Electron treatment of wood pulp can significantly reduce the amounts of chemicals used for producing viscose and the production of hazardous pollutants. Acsion Industries has worked with companies worldwide to demonstrate the benefits of using electron treated pulp for producing viscose (rayon). This paper describes the viscose process, the benefits of using electron treatment in the viscose process, and Acsion's efforts in developing this technology.

  5. Magnet options for sensors for the pulp and paper industry

    International Nuclear Information System (INIS)

    Green, M.A.; Barale, P.J.; Fong, C.G.; Luft, P.A.; Reimer, J.A.; Yahnke, M.S.

    2001-01-01

    The Lawrence Berkeley National Laboratory (LBNL) has been developing sensors for the pulp and paper industry that uses a magnetic field. The applications for magnetic sensors that have studied include (1) sensors for the measurement of the water and ice content of wood chips entering the pulping mill, (2) sensors for measuring the water content and other constituents of the black liquor leaving the paper digester, and (3) sensors for measuring paper thickness and water content as the paper is being processed. These tasks can be done using nuclear magnetic resonance (NMR). The magnetic field used for doing the NMR can come from either permanent magnets or superconducting magnets. The choice of the magnet is dependent on a number of factors, which include the size of the sample and field strength needed to do the sensing task at hand. This paper describes some superconducting magnet options that can be used in the pulp and paper industry.

  6. Outcomes of Different Vital Pulp Therapy Techniques on Symptomatic Permanent Teeth: A Case Series

    OpenAIRE

    Asgary, Saeed; Fazlyab, Mahta; Sabbagh, Sedigheh; Eghbal, Mohammad Jafar

    2014-01-01

    In modern endodontics, vital pulp therapy (VPT) has been considered an ultra-conservative treatment modality. Based on the level of pulp preservation, VPT includes stepwise excavation, indirect pulp capping (IDPC), direct pulp capping (DPC), miniature pulpotomy (MP), partial/Cvek pulpotomy and coronal/complete pulpotomy (CP). The present article reviews the treatment outcomes of 94 permanent teeth with irreversible pulpitis treated with either IDPC (n=28), DPC (n=28), MP (n=29) or CP (n=9) us...

  7. Engineering bacterial motility towards hydrogen-peroxide.

    Science.gov (United States)

    Virgile, Chelsea; Hauk, Pricila; Wu, Hsuan-Chen; Shang, Wu; Tsao, Chen-Yu; Payne, Gregory F; Bentley, William E

    2018-01-01

    Synthetic biologists construct innovative genetic/biological systems to treat environmental, energy, and health problems. Many systems employ rewired cells for non-native product synthesis, while a few have employed the rewired cells as 'smart' devices with programmable function. Building on the latter, we developed a genetic construct to control and direct bacterial motility towards hydrogen peroxide, one of the body's immune response signaling molecules. A motivation for this work is the creation of cells that can target and autonomously treat disease, the latter signaled by hydrogen peroxide release. Bacteria naturally move towards a variety of molecular cues (e.g., nutrients) in the process of chemotaxis. In this work, we engineered bacteria to recognize and move towards hydrogen peroxide, a non-native chemoattractant and potential toxin. Our system exploits oxyRS, the native oxidative stress regulon of E. coli. We first demonstrated H2O2-mediated upregulation motility regulator, CheZ. Using transwell assays, we showed a two-fold increase in net motility towards H2O2. Then, using a 2D cell tracking system, we quantified bacterial motility descriptors including velocity, % running (of tumble/run motions), and a dynamic net directionality towards the molecular cue. In CheZ mutants, we found that increased H2O2 concentration (0-200 μM) and induction time resulted in increased running speeds, ultimately reaching the native E. coli wild-type speed of ~22 μm/s with a ~45-65% ratio of running to tumbling. Finally, using a microfluidic device with stable H2O2 gradients, we characterized responses and the potential for "programmed" directionality towards H2O2 in quiescent fluids. Overall, the synthetic biology framework and tracking analysis in this work will provide a framework for investigating controlled motility of E. coli and other 'smart' probiotics for signal-directed treatment.

  8. Peroxide coordination of tellurium in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Mikhaylov, Alexey A.; Medvedev, Alexander G. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel); Churakov, Andrei V.; Grishanov, Dmitry A.; Prikhodchenko, Petr V. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Lev, Ovadia [The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel)

    2016-02-15

    Tellurium-peroxo complexes in aqueous solutions have never been reported. In this work, ammonium peroxotellurates (NH{sub 4}){sub 4}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2} (1) and (NH{sub 4}){sub 5}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH).1.28 H{sub 2}O.0.72 H{sub 2}O{sub 2} (2) were isolated from 5 % hydrogen peroxide aqueous solutions of ammonium tellurate and characterized by single-crystal and powder X-ray diffraction analysis, by Raman spectroscopy and thermal analysis. The crystal structure of 1 comprises ammonium cations and a symmetric binuclear peroxotellurate anion [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2}]{sup 4-}. The structure of 2 consists of an unsymmetrical [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH)]{sup 5-} anion, ammonium cations, hydrogen peroxide, and water. Peroxotellurate anions in both 1 and 2 contain a binuclear Te{sub 2}(μ-OO){sub 2}(μ-O) fragment with one μ-oxo- and two μ-peroxo bridging groups. {sup 125}Te NMR spectroscopic analysis shows that the peroxo bridged bitellurate anions are the dominant species in solution, with 3-40 %wt H{sub 2}O{sub 2} and for pH values above 9. DFT calculations of the peroxotellurate anion confirm its higher thermodynamic stability compared with those of the oxotellurate analogues. This is the first direct evidence for tellurium-peroxide coordination in any aqueous system and the first report of inorganic tellurium-peroxo complexes. General features common to all reported p-block element peroxides could be discerned by the characterization of aqueous and crystalline peroxotellurates. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Comparison of sensitivity of repair-proficient and repair-deficient strains of Bacillus subtilis to ultraviolet irradiation and hydrogen peroxide

    International Nuclear Information System (INIS)

    Bayliss, C.E.; Shah, J.; Waites, W.M.

    1982-01-01

    Dormant bacterial spores are very resistant to irradiation with ultraviolet (UV) light. The authors have shown that simultaneous treatment with far-UV (254 nm) and hydrogen peroxide in a kill up to 2000-fold greater than that produced by irradiation either alone or followed by treatment with hydrogen peroxide. UV irradiation of hydrogen peroxide produces free hydroxyl radicals which are particularly lethal to microorganisms but free radical quenchers fail to protect spores against simultaneous UV and hydrogen peroxide. It is possible, therefore, that another mechanism is responsible for this synergistic killing. In this study the resistance was examined to simultaneous treatment with UV and hydrogen peroxide of a mutant of Bacillus subtilis which forms UV-sensitive spores. (Auth.)

  10. Anthraquinone-A Review of the Rise and Fall of a Pulping Catalyst

    Science.gov (United States)

    Peter W. Hart; Alan W. Rudie

    2014-01-01

    The application of anthraquinone (AQ) as a pulping catalyst has been well documented in scientific studies and mill applications. AQ is known to increase the rate of delignification, enabling a reduction in pulping time, temperature, or chemical charge and an increase in pulp yield. Specific details of AQ use are not extensively reviewed in this work. The review...

  11. Studies of lignin transformation in polyoxometalate (POM) bleaching of kraft pulp

    Science.gov (United States)

    Biljana Bujanovic; Richard S. Reiner; Kolby C. Hirth; Sally A. Ralph; Rajai H. Atalla

    2005-01-01

    In order to elucidate changes occurring in lignin during polyoxometalate delignification of kraft pulp, residual lignins of a series of POM- delignified kraft pulps of decreasing kappa number were isolated and characterized. Oxidative treatment of commercial unbleached kraft pulp was performed using complex POM solutions containing the active [SiVW11O40]anion. For...

  12. Alkaline Pulping and Bleaching of Acacia auriculiformis Grown in Bangladesh

    OpenAIRE

    JAHAN, M. Sarwar; SABINA, Rowshan; RUBAIYAT, Arjumand

    2014-01-01

    The physical, chemical, and morphological characteristics of Acacia auriculiformis were evaluated in terms of its suitability for papermaking. The fiber length (1.1 mm) of A. auriculiformis in this study was within the range of tropical hardwoods. The lignin content in A. auriculiformis was 19.4% and a-cellulose 44.1%, which was within the range of other acacias, but that of extractives was higher. Soda, soda-AQ, and kraft processes were studied in pulping. Screened pulp yield was increased w...

  13. Effect of cadmium chloride on hepatic lipid peroxidation in mice

    DEFF Research Database (Denmark)

    Andersen, H R; Andersen, O

    1988-01-01

    Intraperitoneal administration of cadmium chloride to 8-12 weeks old CBA-mice enhanced hepatic lipid peroxidation. A positive correlation between cadmium chloride dose and level of peroxidation was observed in both male and female mice. A sex-related difference in mortality was not observed...... but at a dose of 25 mumol CdCl2/kg the level of hepatic lipid peroxidation was higher in male mice than in female mice. The hepatic lipid peroxidation was not increased above the control level in 3 weeks old mice, while 6 weeks old mice responded with increased peroxidation as did 8-12 weeks old mice....... The mortality after an acute toxic dose of cadmium chloride was the same in the three age groups. Pretreatment of mice with several low intraperitoneal doses of cadmium chloride alleviated cadmium induced mortality and lipid peroxidation. The results demonstrate both age dependency and a protective effect...

  14. Stone-ground wood pulp-reinforced polypropylene composites: Water uptake and thermal properties

    Directory of Open Access Journals (Sweden)

    Joan Pere López

    2012-11-01

    Full Text Available Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC and thermogravimetric analysis (TGA were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC.

  15. Mechanics

    CERN Document Server

    Hartog, J P Den

    1961-01-01

    First published over 40 years ago, this work has achieved the status of a classic among introductory texts on mechanics. Den Hartog is known for his lively, discursive and often witty presentations of all the fundamental material of both statics and dynamics (and considerable more advanced material) in new, original ways that provide students with insights into mechanical relationships that other books do not always succeed in conveying. On the other hand, the work is so replete with engineering applications and actual design problems that it is as valuable as a reference to the practicing e

  16. Nutritional Value of Tamarindus Indica Fruit Pulp

    International Nuclear Information System (INIS)

    Chiteva, R.; Kitui, J.L

    2007-01-01

    In Kenya Tamarindus Indica (Tamarind) fruits are not fully utilized despite their abundance in Nyanza, Rift Valley and Eastern provinces. This study determined the nutritional composition of the edible fruit pulp to enhance utilization. The edible portion of Tamarindus indica fruit ('Ukwaju' in Kiswahili) was analysed for it's chemical and nutritional composition. The fruit was sampled from Kitui, Mwingi and Makueni districts of Ukambani, with an assumption that they could be climatically different. The analysis carried out included moisture content, sulphated ash, Vitamin C content, crude protein and minerals namely Na, Ca, Mg, Fe, Zn, Cu and Mn. The energy contents were determined and total carbohydrates calculated. The results showed very low protein content of 0.01% for Kvisuni and Makindu divisions, while Katse and Kyanundu in Mwingi and TARDA in Makueni districts gave the highest value of 0.02% . This is a fairly low protein content compared with other indigenous fruits like Andasonia digitata (Baobab) with a value of 2.9%. The fat content was also low, especially for Makueni that had a value of 0.04% for the unripe fruits while Mwingi gave 0.04% for those fruits that were ripe. Vitamin C content was similar for the fruit from the three districts (8mg100g-1 ) sample. The fruits also contained an appreciable high internal energy level with Mbitini recording highest at 2.94 kcal. All samples had levels of Fe above 1mg100g-1 . Sodium was also available in all samples with TARDA sample having the highest (0.8mg/100g-1 ) . Potassium values were over 200 mg100g-1 s ample for all samples with TARDA leading (1050 mg100g-1 ) . Calcium in all samples was over 20 mg100g-1 w hile mg was 30 mg100g-1 w ith Makindu having the highest value of 75.2mg100g-1 . This fruit, therefore has the potential of providing nutrients and can be used as a food supplement

  17. Hydrogen peroxide probes directed to different cellular compartments.

    OpenAIRE

    Mikalai Malinouski; You Zhou; Vsevolod V Belousov; Dolph L Hatfield; Vadim N Gladyshev

    2011-01-01

    Background Controlled generation and removal of hydrogen peroxide play important roles in cellular redox homeostasis and signaling. We used a hydrogen peroxide biosensor HyPer, targeted to different compartments, to examine these processes in mammalian cells. Principal Findings Reversible responses were observed to various redox perturbations and signaling events. HyPer expressed in HEK 293 cells was found to sense low micromolar levels of hydrogen peroxide. When targeted to various cellular ...

  18. Radiation-induced peroxidation of egg lecithin liposomes

    International Nuclear Information System (INIS)

    Bisby, R.H.; Cundall, R.B.; Tomaszewski, K.E.; Coleman, M.H.; Gould, G.

    1983-01-01

    Peroxidation of multilamellar vesicles of egg lecithin was measured following γ-irradiation of oxygen saturated suspensions. The addition of hydroxyl radical scavengers and the enzymes superoxide dismutase and catalase was used to show that hydroxyl radicals were the major species initiating peroxidation. Superoxide radicals were found to be much less effective initiators of peroxidation. Trolox C, a water soluble analogue of vitamin E, was found to act as an efficient antioxidant in this system. (author)

  19. Modification of NSSC pulp broke fibers using layering method and investigating its effect on paper properties

    Directory of Open Access Journals (Sweden)

    hamidreza rudi

    2016-12-01

    Full Text Available In the current study, modification of NSSC pulp broke fibers was done by forming starch polymeric multilayers, using Layer-by-Layer (LbL layering method. After fiber slushing and preparation of pulp suspension with 0.5% consistency and conductivity formation of about 437 µS/cm, adding water solution of 1 mM NaCl, the experiments of fibers treatment were conducted to build the polymeric layers (up to 5 consecutive layers. Afterward, water retention value (WRV of fibers was calculated in samples to evaluate the influence of this method on fibers hydrophilicity. The fibers were then used to prepare standard handsheets (60±3g/m2 and the physical and strength properties of sheets were evaluated as a function of the number of layers deposited on the fibers. The results showed that the WRV index of the fibers was improved by the LbL treatment of NSSC broke pulp fibers, due to the increase in starch electrostatic absorption. Successive variation in paper apparent density increase and paper thickness decrease confirmed the construction of starch multilayers on the surface of broke fibers. Formation of such multilayers on broke fibers has led to considerable improvement in tensile index (from 13.21 N.m/g to 30.65 N.m/g and burst index (from 1.23 kPa.m2/g to 2.36 kPa.m2/g. Also, the prepared SEM micrographs approve the sheet web compaction and paper mechanical improvement resulted due to an increase in inter-fiber bonding.

  20. Use of coffee (Coffea arabica pulp for the production of briquettes and pellets for heat generation

    Directory of Open Access Journals (Sweden)

    Robert Cubero-Abarca

    2014-10-01

    Full Text Available Coffee bean (Coffea arabica processing generates high amount of residues that are sources of environmental pollution. Therefore, an appropriate solution is needed. The objective of this study was to determine the potential of coffee pulp to produce briquettes and pellets. The study included pulp drying (using air, solar and hot air methods; the production of briquettes and pellets; the evaluation of their energy, physical and mechanical properties; and the evaluation of pellet quality using X-ray densitometry. The results showed that the pulp presented an initial moisture content of 90%, resulting in drying times of 699, 308 and 55 hours for air, solar and hot air drying, respectively, and the calorific values of the pellets and briquettes were 12,501 kJ kg-1 and 11,591 kJ kg-1, respectively. The ash content was 8.68% for the briquettes and 6.74% for the pellets. The density of the briquettes was 1,110 kg m-3, compared with 1,300 kg m-3 for the pellets. The apparent densities were 1,000 kg m-3 and 600 kg m-3 for the briquettes and pellets, respectively, and the water absorptions by the briquettes were 7.90% and 8.10% by the pellets. The maximum horizontal compression effort was 26.86 kg cm-2, measured in the pellets, compared with 4.52 kg cm-2 in the briquettes. The maximum horizontal load was 93.24 kg, measured in the briquettes, compared with 33.50 kg in the pellets. The value of the pellet durability test was 75.54%. X-ray densitometry showed that the pellet was uniform and a few cracks were observed on the pellet surface.

  1. Modeling fiber motion in a pulp pressure screen: the effect of slot shape

    International Nuclear Information System (INIS)

    Dong, S.; Salcudean, M.; Gartshore, I.

    2003-01-01

    A pressure screen is a piece of equipment in the pulp and paper industry used either to remove contaminants from the pulp suspension or to separate fibers having different properties. Contaminants such as fiber bundles, bark and plastic specks are introduced when fibers are separated from the wood by mechanical or chemical pulping processes. Contaminants significantly affect the strength and smoothness of the paper and must be removed before the final paper is produced. The screen plate is a critical part of the pressure screen and its design is the key to screen performance. This paper uses a new and comprehensive CFD simulation tool to examine the flow and fiber behavior in a single slot screen having any reasonable slot shape. -This simulation tool includes three coupled models: first, the flow model solves the Reynolds Averaged Navier-Stokes (RANS) equation using the standard k - ε turbulence model to predict the flow field in the equipment. Second, a three-dimensional flexible fiber model is used to track the fiber trajectory in the screen. Third, a very general wall model is used to deal with the case when a fiber touches the equipment wall. The simulated results show that the slot shape has a critical influence on fiber behavior and screen performance. Three general slot shapes were investigated: the smooth slot, the step-step contour slot and slope-slope contour slot. Of these the slope-slope contour slot provides the best passage for the fibers with a length of 1mm and 3mm. (author)

  2. Pulp revascularization after root canal decontamination with calcium hydroxide and 2% chlorhexidine gel.

    Science.gov (United States)

    Soares, Adriana de Jesus; Lins, Fernanda Freitas; Nagata, Juliana Yuri; Gomes, Brenda Paula Figueiredo de Almeida; Zaia, Alexandre Augusto; Ferraz, Caio Cezar Randi; de Almeida, José Flávio Affonso; de Souza-Filho, Francisco José

    2013-03-01

    Pulp revascularization may be considered a promising alternative for necrotic immature teeth. Many studies have accomplished passive decontamination associated with an antibiotic paste. To date, there is no report evaluating calcium hydroxide associated with 2% chlorhexidine gel for revascularization therapy. The aim of this case report was to describe a new proposal for pulp revascularization with mechanical decontamination and intracanal medication composed of calcium hydroxide and 2% chlorhexidine gel. The patient, a 9-year-old girl, suffered an intrusion associated with pulp exposure caused by an enamel-dentin fracture in her maxillary left central incisor. After diagnosis, treatment consisted of revascularization therapy with gentle manual instrumentation of the cervical and medium thirds of the root in addition to intracanal medication with calcium hydroxide and 2% chlorhexidine gel for 21 days. In the second session, a blood clot was stimulated up to the cervical third of the root canal. Mineral trioxide aggregate (MTA; Angelus, Londrina, Paraná, Brazil) was used for cervical sealing of the canal. Coronal sealing was performed with temporary filling material and composite resin. During the follow-up period, the root canal space showed a progressive decrease in width, mineralized tissue deposition on root canal walls, and apical closure. A cone-beam computed tomography scan taken at the 2-year follow-up confirmed these findings and did not show complete root canal calcification. This new proposal for revascularization therapy with 2% chlorhexidine gel may be used for the treatment of necrotic immature root canals. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  3. Composite grafting with pulp adipofascial advancement flaps for treating non-replantable fingertip amputations.

    Science.gov (United States)

    Lai, Hsin-Ti; Wu, Sheng-Hua; Lai, Ya-Wei; Hsieh, Tung-Ying; Lee, Su-Shin; David Wang, Hui-Min; Chang, Kao-Ping; Lin, Sin-Daw; Lai, Chung-Sheng; Huang, Shu-Hung

    2016-11-01

    Non-replantable fingertip amputation is still a clinical challenge. We performed modified composite grafting with pulp adipofascial advancement flap for Hirase IIA fingertip amputations. Results from a series of patients are presented and achieved better outcome than traditional composite grafting. From September 2012 to April 2014, fourteen patients with sixteen digits were included in our study. Mean age of patients was 43.9 years (20-71 years). All of our patients underwent this procedure under digital block anesthesia. We performed pulp adipofascial advancement flap for better soft tissue coverage of bone exposure stump first. The amputated parts were defatted, trimming, and reattached as composite graft. Age and gender of patients, injured finger, Hirase classification, mechanism of trauma, overall graft survival area, two-point discrimination (2PD) (mm) at six-month, length of shortening of digit, The average disabilities of the arm, shoulder, and hand (DASH) score and subjective self-evaluation questionnaire at 6 month were recorded. Average graft survival area was 89% (75-100%). Average length of shortening was 2.2 mm (1.8-3.5 mm). 2PD at six-month after surgery was 6.3 mm in average (5-8 mm). Average DASH score at 6 month was 1.45 (0.83-2.5). The self-evaluated aesthetic results showed twelve patients (85.7%) were very satisfied, and no patient was completely unsatisfied. In Hirase zone IIA traumatic fingertip amputation where replantation is difficult, our modified technique of composite grafting with pulp adipofascial advancement flap provided an alternative choice with high successful rate, acceptable functional and aesthetic outcomes. © 2016 Wiley Periodicals, Inc. Microsurgery, 2016. © 2015 Wiley Periodicals, Inc. Microsurgery 36:651-657, 2016. © 2016 Wiley Periodicals, Inc.

  4. Precipitation of uranium concentrates by hydrogen peroxide

    International Nuclear Information System (INIS)

    Barbosa Filho, O.

    1986-12-01

    An experimental study on the (UO 4 .xH 2 ) uranyl peroxide precipitation from a uranium process strip solution is presented. The runs were performed in a batch reactor, in laboratory scale. The main objective was to assess the possibility of the peroxide route as an alternative to a conventional ammonium diuranate process. The chemical composition of process solution was obtained. The experiments were conducted according to a factorial design, aiming to evaluate the effects of initial pH, precipitation pH and H 2 O 2 /UO 2 2+ ratio upon the process. The responses were measured in terms of the efficiency of U precipitation, the content of U in the precipitates and the distribution of impurities in the precipitates. The results indicated that the process works is satisfactory on the studied conditions and depending on conditions, it is possible to achieve levels of U precipitation efficiency greater than 99.9% in reaction times of 2 hours. The precipitates reach grades around 99% U 3 O 8 after calcination (900 0 C) and impurities fall below the limit for penalties established by the ASTM and the Allied Chemical Standards. The precipitates are composed of large aggregates of crystals of 1-4 μm, are fast settling and filtering, and are free-flowing when dry. (Author) [pt

  5. Antioxidant effect of bisphosphonates and simvastatin on chondrocyte lipid peroxidation

    International Nuclear Information System (INIS)

    Dombrecht, E.J.; De Tollenaere, C.B.; Aerts, K.; Cos, P.; Schuerwegh, A.J.; Bridts, C.H.; Van Offel, J.F.; Ebo, D.G.; Stevens, W.J.; De Clerck, L.S.

    2006-01-01

    The objective of this study was to evaluate the effect of bisphosphonates (BPs) and simvastatin on chondrocyte lipid peroxidation. For this purpose, a flow cytometrical method using C11-BODIPY 581/591 was developed to detect hydroperoxide-induced lipid peroxidation in chondrocytes. Tertiary butylhydroperoxide (t-BHP) induced a time and concentration dependent increase in chondrocyte lipid peroxidation. Addition of a Fe 2+ /EDTA complex to t-BHP or hydrogen peroxide (H 2 O 2 ) clearly enhanced lipid peroxidation. The lipophilic simvastatin demonstrated a small inhibition in the chondrocyte lipid peroxidation. None of three tested BPs (clodronate, pamidronate, and risedronate) had an effect on chondrocyte lipid peroxidation induced by t-BHP. However, when Fe 2+ /EDTA complex was added to t-BHP or H 2 O 2 , BPs inhibited the lipid peroxidation process varying from 25% to 58%. This study demonstrates that BPs have antioxidant properties as iron chelators, thereby inhibiting the chondrocyte lipid peroxidation. These findings add evidence to the therapeutic potential of bisphosphonates and statins in rheumatoid arthritis

  6. Hydrogen Peroxide Probes Directed to Different Cellular Compartments

    Science.gov (United States)

    Malinouski, Mikalai; Zhou, You; Belousov, Vsevolod V.; Hatfield, Dolph L.; Gladyshev, Vadim N.

    2011-01-01

    Background Controlled generation and removal of hydrogen peroxide play important roles in cellular redox homeostasis and signaling. We used a hydrogen peroxide biosensor HyPer, targeted to different compartments, to examine these processes in mammalian cells. Principal Findings Reversible responses were observed to various redox perturbations and signaling events. HyPer expressed in HEK 293 cells was found to sense low micromolar levels of hydrogen peroxide. When targeted to various cellular compartments, HyPer occurred in the reduced state in the nucleus, cytosol, peroxisomes, mitochondrial intermembrane space and mitochondrial matrix, but low levels of the oxidized form of the biosensor were also observed in each of these compartments, consistent with a low peroxide tone in mammalian cells. In contrast, HyPer was mostly oxidized in the endoplasmic reticulum. Using this system, we characterized control of hydrogen peroxide in various cell systems, such as cells deficient in thioredoxin reductase, sulfhydryl oxidases or subjected to selenium deficiency. Generation of hydrogen peroxide could also be monitored in various compartments following signaling events. Conclusions We found that HyPer can be used as a valuable tool to monitor hydrogen peroxide generated in different cellular compartments. The data also show that hydrogen peroxide generated in one compartment could translocate to other compartments. Our data provide information on compartmentalization, dynamics and homeostatic control of hydrogen peroxide in mammalian cells. PMID:21283738

  7. Hydrogen peroxide probes directed to different cellular compartments.

    Directory of Open Access Journals (Sweden)

    Mikalai Malinouski

    2011-01-01

    Full Text Available Controlled generation and removal of hydrogen peroxide play important roles in cellular redox homeostasis and signaling. We used a hydrogen peroxide biosensor HyPer, targeted to different compartments, to examine these processes in mammalian cells.Reversible responses were observed to various redox perturbations and signaling events. HyPer expressed in HEK 293 cells was found to sense low micromolar levels of hydrogen peroxide. When targeted to various cellular compartments, HyPer occurred in the reduced state in the nucleus, cytosol, peroxisomes, mitochondrial intermembrane space and mitochondrial matrix, but low levels of the oxidized form of the biosensor were also observed in each of these compartments, consistent with a low peroxide tone in mammalian cells. In contrast, HyPer was mostly oxidized in the endoplasmic reticulum. Using this system, we characterized control of hydrogen peroxide in various cell systems, such as cells deficient in thioredoxin reductase, sulfhydryl oxidases or subjected to selenium deficiency. Generation of hydrogen peroxide could also be monitored in various compartments following signaling events.We found that HyPer can be used as a valuable tool to monitor hydrogen peroxide generated in different cellular compartments. The data also show that hydrogen peroxide generated in one compartment could translocate to other compartments. Our data provide information on compartmentalization, dynamics and homeostatic control of hydrogen peroxide in mammalian cells.

  8. Synthesis and thermal properties of strontium and calcium peroxides

    Science.gov (United States)

    Philipp, Warren H.; Kraft, Patricia A.

    1989-01-01

    A practical synthesis and a discussion of some chemical properties of pure strontium peroxide and calcium peroxide are presented. The general synthesis of these peroxides involves precipitation of their octahydrates by addition of H2O2 to aqueous ammoniacal Sr(NO3)2 or CaCl2. The octahydrates are converted to the anhydrous peroxides by various dehydration techniques. A new x-ray diffraction powder pattern for CaO2 x 8H2O is given from which lattice parameters a=6.212830 and c=11.0090 were calculated on the basis of the tetragonal crystal system.

  9. Effect of antioxidants and silicates on peroxides in povidone.

    Science.gov (United States)

    Narang, Ajit S; Rao, Venkatramana M; Desai, Divyakant S

    2012-01-01

    Reactive peroxides in povidone often lead to degradation of oxidation-labile drugs. To reduce peroxide concentration in povidone, the roles of storage conditions, antioxidants, and silicates were investigated. Povidone alone and its physical mixtures with ascorbic acid, propyl gallate, sodium sulfite, butylated hydroxyanisole (BHA), or butylated hydroxytoluene (BHT) were stored at 25 °C and 40 °C, at 11%, 32%, and 50% relative humidity. In addition, povidone solution in methanol was equilibrated with silicates (silica gel and molecular sieves), followed by solvent evaporation to recover povidone powder. Peroxide concentrations in povidone were measured. The concentration of peroxides in povidone increased under very-low-humidity storage conditions. Among the antioxidants, ascorbic acid, propyl gallate, and sodium sulfite reduced the peroxide concentration in povidone, whereas BHA and BHT did not. Water solubility appeared to determine the effectiveness of antioxidants. Also, some silicates significantly reduced peroxide concentration in povidone without affecting its functionality as a tablet binder. Porosity of silicates was critical to their ability to reduce the peroxide concentration in povidone. A combination of these approaches can reduce the initial peroxide concentration in povidone and minimize peroxide growth under routine storage conditions. Copyright © 2011 Wiley-Liss, Inc.

  10. Microarray evaluation of gene expression profiles in inflamed and healthy human dental pulp: the role of IL1beta and CD40 in pulp inflammation.

    Science.gov (United States)

    Gatta, V; Zizzari, V L; Dd ' Amico, V; Salini, L; D' Aurora, M; Franchi, S; Antonucci, I; Sberna, M T; Gherlone, E; Stuppia, L; Tetè, S

    2012-01-01

    Dental pulp undergoes a number of changes passing from healthy status to inflammation due to deep decay. These changes are regulated by several genes resulting differently expressed in inflamed and healthy dental pulp, and the knowledge of the processes underlying this differential expression is of great relevance in the identification of the pathogenesis of the disease. In this study, the gene expression profile of inflamed and healthy dental pulps were compared by microarray analysis, and data obtained were analyzed by Ingenuity Pathway Analysis (IPA) software. This analysis allows to focus on a variety of genes, typically expressed in inflamed tissues. The comparison analysis showed an increased expression of several genes in inflamed pulp, among which IL1β and CD40 resulted of particular interest. These results indicate that gene expression profile of human dental pulp in different physiological and pathological conditions may become an useful tool for improving our knowledge about processes regulating pulp inflammation.

  11. CIDEX, SAVLON AND HYDROGEN PEROXIDE: WHICH OF THEM IS MORE EFFECTIVE IN DISINFECTION OF VENTILATOR TUBES

    Directory of Open Access Journals (Sweden)

    H SOLTANI NEZHAD

    2001-12-01

    Full Text Available Introduction: Nasocomial infections threat any hospitalized patient, specially in intensive care unit. Incidence of these infections has been reported from 1.9 to more than 25 percent. The most common nasocomial infection in intensive care units (ICU is pneumonia caused by endotraheal intubation and mechanical ventilation. The best procedure for pneumonia prevention in patients under mechanical ventilation is utilization of suitable and proper techniques for equipment sterilization: The goal of this study is determination and comparison of disinfectant materials (cidex, savlon and hydrogen peroxide about their effects on incidence and type of mechanical ventilators breathing tubes contamination in intensive care unit. Methods: This is an experimental trial which was done on three groups of mechanical ventilator breathing tubes. Each group contained 20 samples. These three groups of breathing tubes were disinfected with cidex, savlon and hydrogen peroxide. Samples were obtained from tubes for microbial culture berore and after disinfection. Samples were cultured on blood agar. The results of microbial culturing were compared between three groups. Results: There was no significant difference between three groups of breathing tubes about microbial types and number of colony counted before disinfection. There was no significant difference between cultured colony numbers in three groups before and after disinfection. Cidex, savlon and hydrogen peroxide could decrease incidence of contamination to 100, 98.09 and 100 percent, respectively. Discussion: All of tested chemical materials have the same results in disinfection. Hydrogen peroxide has less adverse effect on human and environment than cidex. It is less expensive than cidex. So, we recommend to use this material for disifection of mechanical ventilator berthing tubes.

  12. Recovery of ovary size, follicle cell apoptosis, and HSP70 expression in fish exposed to bleached pulp mill effluent

    Energy Technology Data Exchange (ETDEWEB)

    Janz, D. M.; Weber, L. P. [Oklahoma State Univ., Stillwater, OK (United States); McMaster, M. E.; Munkittrrick, K. R. [Environment Canada, Burlington, ON (Canada); Van Der Kraak, G. [Guelph Univ., Dept. of Zoology, ON (Canada)

    2001-03-01

    Apoptosis of granulosa cells that provide hormonal support for the oocyte is the normal mechanism by which atresia ( reduced ovarian size, decreased fecundity, delayed sexual maturation, alterations in plasma sex steroid levels, etc) occurs in mammals, birds and possibly fish. The objective of this study is to determine ovarian cell apoptosis, gonadosomatic index (GSI) and heat shock protein (HSP70) expression during the growth stage of ovarian development in white sucker fish in order to compare samples of fish collected upstream and downstream of a bleached kraft pulp mill in Ontario. Fish for the study were collected in two different years, before and after the pulp mill undertook a number of improvements to eliminate the release of process chemicals. Results showed a 3.4-fold increase in ovarian cell apoptosis in growing white sucker collected four km downstream of the bleached kraft pulp mill in 1996 (before the improvements) compared to fish collected from upstream sources. The elevated ovarian cell apoptosis was associated with significant reduction in gonadosomatic index in fish collected downstream. There were no differences in ovarian cell apoptosis or gonadosomatic index between fish collected upstream and four km downstream of the mill in September 1998 (after the improvements.) Based on the results, it may be concluded that chronic stimulation of ovarian cell apoptosis by certain components of bleached kraft pulp mill effluents represents an important cellular mechanism for reducing the size of ovaries and other related reproductive responses in female fish exposed to these effluents. Although the specific effluent components are not known, the improvements undertaken between 1996 and 1998 resulted in significant enough recovery of these responses to justify the belief in a cause-effect relationship. 32 refs., 1 tab., 2 figs.

  13. Amino acid derivative-mediated detoxification and functionalization of dual cure dental restorative material for dental pulp cell mineralization.

    Science.gov (United States)

    Minamikawa, Hajime; Yamada, Masahiro; Iwasa, Fuminori; Ueno, Takeshi; Deyama, Yoshiaki; Suzuki, Kuniaki; Yawaka, Yasutaka; Ogawa, Takahiro

    2010-10-01

    Current dental restorative materials are only used to fill the defect of hard tissues, such as dentin and enamel, because of their cytotoxicity. Therefore, exposed dental pulp tissues in deep cavities must be first covered by a pulp capping material like calcium hydroxide to form a layer of mineralized tissue. However, this tissue mineralization is based on pathological reaction and triggers long-lasting inflammation, often causing clinical problems. This study tested the ability of N-acetyl cysteine (NAC), amino acid derivative, to reduce cytotoxicity and induce mineralized tissue conductivity in resin-modified glass ionomer (RMGI), a widely used dental restorative material having dual cure mechanism. Rat dental pulp cells were cultured on untreated or NAC-supplemented RMGI. NAC supplementation substantially increased the percentage of viable cells from 46.7 to 73.3% after 24-h incubation. Cell attachment, spreading, proliferative activity, and odontoblast-related gene and protein expressions increased significantly on NAC-supplemented RMGI. The mineralization capability of cells, which was nearly suppressed on untreated RMGI, was induced on NAC-supplemented RMGI. These improved behaviors and functions of dental pulp cells on NAC-supplemented RMGI were associated with a considerable reduction in the production of intracellular reactive oxygen species and with the increased level of intracellular glutathione reserves. These results demonstrated that NAC could detoxify and functionalize RMGIs via two different mechanisms involving in situ material detoxification and antioxidant cell protection. We believe that this study provides a new approach for developing dental restorative materials that enables mineralized tissue regeneration.

  14. EFFECTIVITY OF TWO BLEACHING AGENT OF 10% CARBAMIDE PEROXIDE WITH AND WITHOUT POTASSIUM NITRATE-FLUORIDE (CLINICAL STUDY

    Directory of Open Access Journals (Sweden)

    Ayus Lusiyanti

    2015-06-01

    Full Text Available Tooth bleaching has become a popular treatment for esthetic improvement in dentistry. There are several 10% carbamide peroxide bleaching agents that are available in Indonesia which contained potassium nitrate-fluoride or without potassium nitrate-fluoride. However, there was no clinical report about these products in Indonesia. This study was conducted to compare the effectiveness of two bleaching and sensitivity of tooth and gingiva. Sixty-four participants were divided into 2 groups. The first group was treated with bleaching agent that contained potassium nitrate-fluoride (Opalescence PF, Ultradent. Bleaching treatment was done for 6-8 hours per night over a 2 week-period. Evaluations were performed at the baseline and at 3, 7, 14 day afterwards. Color change was measured using a value-ordered Vita classic shade guide; tooth and gingival sensitivity were examine using Electric Pulp Tester, Gingival Index and patient log. The results showed that there were no statistical differences in degree of color change between the two products. The mean color change after 2 weeks was 7-8 tabs lighter than baseline. Also there was no statistical difference in tooth and gingival sensitivity between the products. It can be concluded that 10% carbamide peroxide containing potassium nitrate-fluoride has the same effectiveness compared to other agent without potassium nitrate-fluoride for tooth color change and tooth and gingival sensitivity.

  15. Vital pulp therapy in symptomatic immature permanent molars: Report of 3 cases

    Directory of Open Access Journals (Sweden)

    SheikhRezaie MS.

    2009-11-01

    Full Text Available "nEndodontic treatment of immature permanent teeth accompanies with several issues. The primary goal when treating such teeth is to maintain pulp vitality so that root development can occur normally. Indications and requirements for vital pulp therapy include asymptomatic and reversible pulpitis. Also there are controversial opinions regarding the ultimate clinical treatment of the vital pulp therapy techniques. In this manuscript we report 3 cases of immature symptomatic permanent molars with irreversible pulpitis caused by caries exposure of the pulp that have been undergone vital pulp therapy successfully.

  16. Recuperation of uranium and gold in mineral pulps by adsorption

    International Nuclear Information System (INIS)

    Bruno, J.B.; Amorim, L.O.

    1985-06-01

    The technological routes for the treatment of the gold and uranium ores are presented. The results obtained during the continuous tests with the uraniferous Ores of Wabo in Somalia are presented. The utilization of 99% of the uranium content in the alkaline pulp is obtained. (C.B.) [pt

  17. Pequi pulp ( Caryocar brasiliense Cambess): Drying kinetics and ...

    African Journals Online (AJOL)

    The entropy values found were -251.01, -250.38 and -250.05 (J.Mol-1K-1) for the same temperatures. The values obtained from the Gibbs free energy for the drying of Pequi pulp increased with increasing temperature. The obtained data were consistent to the drying process, and the mathematical equations were effective ...

  18. Incidence and Distribution of Pulp Stones Found in Radiographic ...

    African Journals Online (AJOL)

    or more in a single tooth, their size varying from minute particles to large masses ... between pulp stones and sex, tooth type, dental arch, side and .... attended Kırıkkale University Dental School (KUDS).Caution .... Beside these disadvantages,.

  19. Comparison of various pulping characteristic of Fraxinus angustifolia ...

    African Journals Online (AJOL)

    Handsheets made from different pulping methods were compared with each other for strength and optical properties. Strength properties were found to be higher for kraft and kraft + anthraquinone processes, while optical properties were found to be higher for cold soda and NSSC processes. Key words: Ash, Fraxinus ...

  20. Selection of Corymbia citriodora for pulp productivity | Brawner ...

    African Journals Online (AJOL)

    Evaluation of a series of spotted gum (Corymbia citirodora) progeny trials, established in the subtropical region of Queensland, Australia, was undertaken to provide information for the development of advanced-generation breeding populations suitable for pulp production. Measurements of growth at two ages were ...