WorldWideScience

Sample records for permissible concentration calculations

  1. Permissible annual depositions and radionuclide concentrations in air

    International Nuclear Information System (INIS)

    Belyaev, V.A.; Golovko, M.Yu.

    1993-01-01

    It is established that it necessary to take into account the other ways of radionuclide intake apart from the inhalation one when determining the standards for radionuclide contamination of the atmospheric air. Whereby it is proposed to standardize annual depositions rather than permissible concentration in the atmospheric air for the ways related to radionuclide releases on the ground surface, which is explained by ambiguity of their dry deposition rate from the air. Formulae and results of calculation of standard characteristics are presented. The permissible radionuclide depositions, related to the intake through food chains are calculated with account for diet diversity, agroclimatic and phenological parameters in different regions of the country

  2. Maximum Permissible Concentrations and Negligible Concentrations for pesticides

    NARCIS (Netherlands)

    Crommentuijn T; Kalf DF; Polder MD; Posthumus R; Plassche EJ van de; CSR

    1997-01-01

    Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) derived for a series of pesticides are presented in this report. These MPCs and NCs are used by the Ministry of Housing, Spatial Planning and the Environment (VROM) to set Environmental Quality Objectives. For some of the

  3. The ecological determination of the permissible concentrations for radioactive contamination

    International Nuclear Information System (INIS)

    Kononovich, A.L.

    1996-01-01

    It is supposed that all inhabitants of the ecosystem are enjoying equal rights. The report describes the approximate method of ecology normalizing of the permissible radionuclide concentrations. Definition of the permissible concentration is made by an indirect way, since the defining criterion is unknown

  4. Maximum permissible concentration (MPC) values for spontaneously fissioning radionuclides

    International Nuclear Information System (INIS)

    Ford, M.R.; Snyder, W.S.; Dillman, L.T.; Watson, S.B.

    1976-01-01

    The radiation hazards involved in handling certain of the transuranic nuclides that exhibit spontaneous fission as a mode of decay were reaccessed using recent advances in dosimetry and metabolic modeling. Maximum permissible concentration (MPC) values in air and water for occupational exposure (168 hr/week) were calculated for 244 Pu, 246 Cm, 248 Cm, 250 Cf, 252 Cf, 254 Cf, /sup 254m/Es, 255 Es, 254 Fm, and 256 Fm. The half-lives, branching ratios, and principal modes of decay of the parent-daughter members down to a member that makes a negligible contribution to the dose are given, and all daughters that make a significant contribution to the dose to body organs following inhalation or ingestion are included in the calculations. Dose commitments for body organs are also given

  5. Maximum permissible concentrations and negligible concentrations for antifouling substances. Irgarol 1051, dichlofluanid, ziram, chlorothalonil and TCMTB

    NARCIS (Netherlands)

    Wezel AP van; Vlaardingen P van; CSR

    2001-01-01

    This report presents maximum permissible concentrations and negligible concentrations that have been derived for various antifouling substances used as substitutes for TBT. Included here are Irgarol 1051, dichlofluanide, ziram, chlorothalonil and TCMTB.

  6. Influence of the composition of radionuclide mixtures on the maximum permissible concentration

    International Nuclear Information System (INIS)

    Schillinger, K.; Schuricht, V.

    1975-08-01

    By dividing radionuclides according to their formation mechanisms it is possible to assess the influence of separate partial mixtures on the maximum permissible concentration (MPC) of the total mixture without knowing exactly their contribution to the total activity. Calculations showed that the MPC of a total mixture of unsoluble radionuclides, which may occur in all fields of peaceful uses of nuclear energy, depends on the gastrointestinal tract as the critical organ and on the composition of the fission product mixture. The influence of fractionation on the MPC can be reglected in such a case, whereas in case of soluble radionuclides this is not possible

  7. On the substantion of permissible concentrations of plutonium isotopes in the water of fresh water and sea water NPP cooling reservoirs

    International Nuclear Information System (INIS)

    Grachev, M.I.; Gusev, D.I.; Stepanova, V.D.

    1985-01-01

    Substantiation of maximum permissible concentration (PC) of plutonium isotopes ( 238 Pu, 239 Pu, 240 Pu) in fresh and sea water cooling reservoirs of NPP with fast neutron reactors is given. The main criterion when calculating permissible plutonium content in water of surface reservoirs is the requirement not to exceed the established limits for radiation doses to persons resulted from water use. Data on coefficients of plutonium concentration in sea and fresh water hydrobionts are presented as well as on plutonium PC in water of fresh and sea water cooling reservoirs and bottom sediments of sea water cooling reservoirs. It is shown that doses to critical groups of population doesn't exceed potentially hazardous levels due to plutonium intake through food chains. But the calculation being carried out further should be corrected

  8. Evaluation of the external radiation exposure dosimetry and calculation of maximum permissible concentration values for airborne materials containing 18F, 15O, 13N, 11C and 133Xe

    International Nuclear Information System (INIS)

    Piltingsrud, H.V.; Gels, G.L.

    1985-01-01

    To better understand the dose equivalent (D.E.) rates produced by airborne releases of gaseous positron-emitting radionuclides under various conditions of cloud size, a study of the external radiation exposure dosimetry of these radionuclides, as well as negatron, gamma and x-ray emitting 133Xe, was undertaken. This included a calculation of the contributions to D.E. as a function of cloud radii, at tissue depths of 0.07 mm (skin), 3 mm (lens of eye) and 10 mm (whole body) from both the particulate and photon radiations emitted by these radionuclides. Estimates of maximum permissible concentration (MPC) values were also calculated based on the calculated D.E. rates and current regulations for personnel radiation protection (CFR84). Three continuous air monitors, designed for use with 133Xe, were evaluated for applications in monitoring air concentrations of the selected positron emitters. The results indicate that for a given radionuclide and for a cloud greater than a certain radius, personnel radiation dosimeters must respond acceptably to only the photon radiations emitted by the radionuclide to provide acceptable personnel dosimetry. For clouds under that radius, personnel radiation dosimeters must also respond acceptably to the positron or negatron radiations to provide acceptable personnel dosimetry. It was found that two out of the three air concentration monitors may be useful for monitoring air concentrations of the selected positron emitters

  9. The calculation of maximum permissible exposure levels for laser radiation

    International Nuclear Information System (INIS)

    Tozer, B.A.

    1979-01-01

    The maximum permissible exposure data of the revised standard BS 4803 are presented as a set of decision charts which ensure that the user automatically takes into account such details as pulse length and pulse pattern, limiting angular subtense, combinations of multiple wavelength and/or multiple pulse lengths, etc. The two decision charts given are for the calculation of radiation hazards to skin and eye respectively. (author)

  10. Account of low temperature hardening in calculation of permissible stresses

    International Nuclear Information System (INIS)

    Novikov, N.V.; Ul'yanenko, A.P.; Gorodyskij, N.I.

    1980-01-01

    Suggested is a calculation scheme of permissible stresses with the account of temperature hardening for steels and alloys, the dependences of strength, plasticity and rupture work of which on cooling temperature do not have threshold changes in a wide range of low temperatures (from 300 to 4.2 K). Application of the suggested scheme is considered on the example of 12Kh18N10T austenitic chromium-nickel steel

  11. Statistic method of research reactors maximum permissible power calculation

    International Nuclear Information System (INIS)

    Grosheva, N.A.; Kirsanov, G.A.; Konoplev, K.A.; Chmshkyan, D.V.

    1998-01-01

    The technique for calculating maximum permissible power of a research reactor at which the probability of the thermal-process accident does not exceed the specified value, is presented. The statistical method is used for the calculations. It is regarded that the determining function related to the reactor safety is the known function of the reactor power and many statistically independent values which list includes the reactor process parameters, geometrical characteristics of the reactor core and fuel elements, as well as random factors connected with the reactor specific features. Heat flux density or temperature is taken as a limiting factor. The program realization of the method discussed is briefly described. The results of calculating the PIK reactor margin coefficients for different probabilities of the thermal-process accident are considered as an example. It is shown that the probability of an accident with fuel element melting in hot zone is lower than 10 -8 1 per year for the reactor rated power [ru

  12. Study on the determination of permissible concentration in sea food

    International Nuclear Information System (INIS)

    Lee, C.M.; Lee, K.J.; Lee, W.K.

    2002-01-01

    Radioactive permissible concentration limit using the data which is suitable for Koreans is not established. In this paper, concentration limit is determined by using Korean food intake. Ministry of science of technology will adopt the new recommendation soon, so at this paper, dose limit of new value in ICRP 60 is used. Experts who have studied on this area worry about over-exposure by estimation of the case that intake contaminated a food by one radionuclide, therefore, complex intake limit is determined about all kinds of fishery products to solve this problem. Derived Food Concentration in single food divided by S(number of samples) and N(number of radionuclides) gives Complex intake limit (Derived Food Concentration in plural food). The value of N and S in this study is 3 and 12 respectively

  13. Maximum permissible concentrations and negligible concentrations for phthalates (dibutylphthalate and di(2-ethylhexyl)phthlate), with emphasis on endocrine disruptive properties

    NARCIS (Netherlands)

    Wezel AP van; Posthumus R; Vlaardingen P van; Crommentuijn T; Plassche EJ van de; CSR

    This report presents maximal permissible concentrations (MPCs) and negligible concentrations (NCs) are derived for di-n-butylphthalate (DBP) and di(2-ethylhexyl)phthalate (DEHP). Phthalates are often mentioned as suspected endocrine disrupters. Data with endpoints related to the endocrine or

  14. Secondary poisoning of cadmium, copper and mercury: implications for the Maximum Permissible Concentrations and Negligible Concentrations in water, sediment and soil

    NARCIS (Netherlands)

    Smit CE; Wezel AP van; Jager T; Traas TP; CSR

    2000-01-01

    The impact of secondary poisoning on the Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) of cadmium, copper and mercury in water, sediment and soil have been evaluated. Field data on accumulation of these elements by fish, mussels and earthworms were used to derive

  15. Determination of permissible exposure doses under the provisions of the regulations on installation and operation of marine reactors

    International Nuclear Information System (INIS)

    1979-01-01

    The Ministry of Transportation defines on radioactive doses in the controlled area that exterior radioactive dose shall be 30 mili-rem for a week; concentrations of radioactive materials in the air or under the water shall be permissible concentrations otherwise specified for the employees multiplied by 0.75 in average for a week and that densities of radioactive materials on the surface of the things contaminated by such materials shall be 1/10 of permissible surface densities provided in a table attached. Permissible exposure dose outside the inspected surrounding area is 0.5 rem for a year. Permissible surface densities are included in a list attached. Permissible accumulative dose for the employees is the figure (unit rem) calculated by the formula D = 5(N-18), when D means permissible accumulative dose and N number of the age. Permissible exposure dose is 3 rem for 3 months for the employees, 1.5 rem for a year for persons other than the employees and 12 rem for the urgent work. Permissible densities for the employees, calculation of doses by interior exposure and permissible densities outside the inspected surrounding area are stipulated in detail with attached lists. (Okada, K.)

  16. Determination of permissible doses under the provisions of the regulations on installation and operation of reactors for power generation

    International Nuclear Information System (INIS)

    1979-01-01

    The determination is defined under the regulations on installation and operation of reactors for power generation. In the controlled area exterior radiation dose shall be 30 mili-rem for a week by the Minister of International Trade and Industry. The concentrations of radioactive materials in the air or under the water shall be permissible concentrations specified for the employees multiplied by 0.75 in average for a week. The densities of radioactive materials on the surface of the things contaminated by such materials shall be 1/10 of permissible surface densities stipulated in the table attached. Permissible exposure dose outside the inspected surrounding area is 0.5 rem for a year. Permissible surface densities are included in the table attached. Permissible accumulative dose for the employees is the figure (unit rem) calculated by the formula D = 5(N-18), when D means permissible accumulative dose and N number of the age. Permissible exposure dose is 3 rem for 3 months for the employees, 1.5 rem for a year for persons other than the employees and 12 rem for the urgent work. Permissible concentrations are defined in detail for the employees and outside the inspected surrounding area. Calculation of exposure dose in the case of interior exposure is particularly provided for. (Okada, K.)

  17. Maximum permissible concentration of radon {sup 222}Rn in air; La concentration maximale admissible du radon 222 dans l'air

    Energy Technology Data Exchange (ETDEWEB)

    Hamard, J; Beau, P G; Ergas, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires, departement de la protection sanitaire, service d' hygiene atomique

    1968-09-01

    In order to verify the validity of the values proposed for the maximum permissible concentration of {sup 222}Rn in air, one can either approach the problem: - by epidemiological studies tending to determine the relation dose-effect both quantitatively and qualitatively; - or by choosing a lung model and clearance constants allowing a more accurate determination of the delivered dose and the localisation of the more severely irradiated portions of the bronchial tree. The radon MPC have been calculated using the model and the respiration constants set up by the I.C.R.P. Task Group on Lung dynamics. Two cases have been considered, i.e. when the radon daughter products behave as soluble materials and as insoluble ones. The values which have been found have been compared with those given up to now by several national and international bodies. (authors) [French] Deux voies d'approche peuvent etre empruntees pour verifier la validite des valeurs proposees pour la concentration maximale admissible du radon 222 dans l'air: - etudes epidemiologiques tendant a preciser qualitativement et quantitativement la relation dose-effet; - choix d'un modele pulmonaire et de constantes d'epuration permettant une determination plus precise de la dose delivree et la localisation des segments de l'arbre pulmonaire les plus irradies. Les auteurs ont utilise pour le calcul de la CMA du radon le modele et les constantes respiratoires proposees par le Task Group on Lungs dynamics de la C.I.P.R. On a pris en consideration le cas ou les descendants du radon se comportent comme des substances solubles et celui ou ils se comportent comme des substances insolubles. Les valeurs trouvees sont comparees a celles proposees jusqu'alors par divers organismes nationaux et internationaux. (auteurs)

  18. Experimental study, in rat wistar, of cadmium distribution and elimination as a function of administration route. Cadmium 109 maximum permissible concentration

    International Nuclear Information System (INIS)

    Valero, Marc.

    1979-01-01

    The absorption and the elimination of cadmium have been investigated in rats wistar after oral administration or after inhalation. Before studying gastro-intestinal absorption, it appeared necessary to precise acute toxicity of orally administred cadmium. The distribution of cadmium within organes was determined following a single or multiple oral doses, and we specially studied retention of a Cd dose ingested after several weeks of treatment with Cd-Acetate. Pulmonary and gastro-intestinal absorption of cadmium after ihalation of Cd-microparticles were studied. Data obtained from these studies on rats and extrapolated to man were used to calculate mximum permissible concentration (M.P.C.) of Cd-109 in water and in air [fr

  19. MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2015-01-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  20. MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2014-01-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  1. A guide for the calculation of the maximum permissible costs for shelters

    International Nuclear Information System (INIS)

    Schwarzlose, H.

    1981-01-01

    Among other things, this paper has the aim to define the scope which is reasonable for shelter costs as well as to inform about their real amount. Various assumptions have been made and examples have been given which seldom coincide with the specific facts. Thus, the possibility of how to find solutions which are precisely appropriate for persons is shown in a formula. The less the income, life expectancy and the number of persons to be considered the less are the maximum permissible costs for shelters. Under certain conditions the permissible costs are lower than the real costs. Thus, taking those assumptions into account, the shelter is not profitable any more. This case, for example, really applies to a couple, 57 years old, without children, with an income of 40,000 DM/year who intend to build an interior shelter. For a family with children who are under age, however, it is always profitable to build an interior basic shelter. (orig.) [de

  2. MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2017-01-01

    The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

  3. MAK and BAT values list 2016. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

    International Nuclear Information System (INIS)

    2016-01-01

    The MAK and BAT values list 2016 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

  4. Calculation of radon concentration in water by toluene extraction method

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Masaaki [Tokyo Metropolitan Isotope Research Center (Japan)

    1997-02-01

    Noguchi method and Horiuchi method have been used as the calculation method of radon concentration in water. Both methods have two problems in the original, that is, the concentration calculated is changed by the extraction temperature depend on the incorrect solubility data and the concentration calculated are smaller than the correct values, because the radon calculation equation does not true to the gas-liquid equilibrium theory. However, the two problems are solved by improving the radon equation. I presented the Noguchi-Saito equation and the constant B of Horiuchi-Saito equation. The calculating results by the improved method showed about 10% of error. (S.Y.)

  5. Contrasting amino acid profiles among permissive and non-permissive hosts of Candidatus Liberibacter asiaticus, putative causal agent of Huanglongbing.

    Directory of Open Access Journals (Sweden)

    Mamoudou Sétamou

    Full Text Available Huanglongbing is a devastating disease of citrus. In this study, a comprehensive profile of phloem sap amino acids (AA in four permissive host plants of Candidatus Liberibacter asiaticus (CLas and three non-permissive Rutaceae plants was conducted to gain a better understanding of host factors that may promote or suppress the bacterium. The AA profiles of Diaphorina citri nymphs and adults were similarly analyzed. A total of 38 unique AAs were detected in phloem sap of the various plants and D. citri samples, with phloem sap of young shoots containing more AAs and at higher concentrations than their mature counterparts. All AAs detected in phloem sap of non-permissive plants were also present in CLas -permissive hosts plus additional AAs in the latter class of plants. However, the relative composition of 18 commonly shared AAs varied between CLas -permissive hosts and non-permissive plants. Multivariate analysis with a partial least square discriminant methodology revealed a total of 12 AAs as major factors affecting CLas host status, of which seven were positively related to CLas tolerance/resistance and five positively associated with CLas susceptibility. Most of the AAs positively associated with CLas susceptibility were predominantly of the glutamate family, notably stressed-induced AAs such as arginine, GABA and proline. In contrast, AAs positively correlated with CLas tolerance/resistance were mainly of the serine family. Further analysis revealed that whereas the relative proportions of AAs positively associated with CLas susceptibility did not vary with host developmental stages, those associated with CLas tolerance/resistance increased with flush shoot maturity. Significantly, the proline-to-glycine ratio was determined to be an important discriminating factor for CLas permissivity with higher values characteristic of CLas -permissive hosts. This ratio could be exploited as a biomarker in HLB-resistance breeding programs.

  6. Maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere in a milk producing area

    Energy Technology Data Exchange (ETDEWEB)

    Bryant, P M

    1963-01-01

    A method is given for calculating, for design purposes, the maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere with respect to milk contamination. In the absence of authoritative advice from the Medical Research Council, provisional working levels for the concentration of phosphorus-32 and sulphur-35 in milk are derived, and details are given of the agricultural assumptions involved in the calculation of the relationship between the amount of the nuclide deposited on grassland and that to be found in milk. The agricultural and meteorological conditions assumed are applicable as an annual average to England and Wales. The results (in mc/day) for phosphorus-32 and sulphur-35 for a number of stack heights and distances are shown graphically; typical values, quoted in a table, include 20 mc/day of phosphorus-32 and 30 mc/day of sulfur-35 as the maximum permissible continuous release rates with respect to ground level releases at a distance of 200 metres from pastureland.

  7. Measured and calculated NO2 concentrations in Amsterdam in 2008

    International Nuclear Information System (INIS)

    Wesseling, J.P.; Nguyen, P.L.; Van der Zee, S.

    2010-08-01

    Calculations using the Dutch standard calculation method for air quality in urban streets performed for 38 streets in Amsterdam in 2008 yield, on average, lower Nitrogen dioxide concentrations than measurements at those locations. This follows from research by the RIVM and the Public Health Service of Amsterdam (GGD Amsterdam). The average difference between measured and calculated concentrations is 11 %. At measuring locations of the National Air Quality Measuring Network in the Netherlands no significant underestimation of concentrations by the model is observed. The research was performed by the Dutch ministry of Housing, Spatial Planning en the Environment (VROM). The air quality in the streets that were investigated is mainly determined by emissions from local traffic. The measurements have been performed during thirteen periods of four weeks each, using so called 'Palmes' diffusion tubes. These measurements have been calibrated using the European reference method that is operational in the permanent measuring stations of the GGD Amsterdam. The calculations were performed using the geometry of the roads and information of the traffic at the measuring locations. Part of the differences can be explained, as some locations are not within the scope of the model. In these situations the model is known to perform slightly less. Apart from local traffic, other sources, like shipping, also contribute to the NO2 background concentrations in streets in Amsterdam. Sources that have only globally been included in the calculation of this background concentration may influence concentrations at specific locations. Further studies on this subject will be conducted in 2010. [nl

  8. Model for calculating the boron concentration in PWR type reactors

    International Nuclear Information System (INIS)

    Reis Martins Junior, L.L. dos; Vanni, E.A.

    1986-01-01

    A PWR boron concentration model has been developed for use with RETRAN code. The concentration model calculates the boron mass balance in the primary circuit as the injected boron mixes and is transported through the same circuit. RETRAN control blocks are used to calculate the boron concentration in fluid volumes during steady-state and transient conditions. The boron reactivity worth is obtained from the core concentration and used in RETRAN point kinetics model. A FSAR type analysis of a Steam Line Break Accident in Angra I plant was selected to test the model and the results obtained indicate a sucessfull performance. (Author) [pt

  9. Long-term calculation of radionuclides concentration in the ocean by OGCM

    International Nuclear Information System (INIS)

    Tsumune, Daisuke; Maruyama, Koki; Nakashiki, Norikazu; Aoyama, Michio; Hirose, Katsumi

    2000-01-01

    The ocean transports of radioactive materials have been carried out from Europe to Japan through the several routes on the world ocean. To sustain the safety of the transport of radioactive materials and to gain the public acceptance, it is necessary evaluate the radionuclide concentration in the ocean at the hypothetical submergence of radioactive materials into the world ocean. The purpose of this study is to develop a new method to evaluate the radionuclides concentration in the world ocean. A method to calculate the concentration of radionuclides in the ocean was developed using an ocean general circulation model (OGCM). The concentration of radionuclides ( 137 Cs, 90 Sr and 239+240 Pu) in the ocean was calculated from 1957 to 1994, on the assumption that these radionuclides were injected into the ocean only as the fallout from the atmospheric weapons tests. The calculated concentrations gave a good agreement with the observed data. The concentration of radionuclides in the ocean was estimated by this method in case of the hypothetical submergence of a package of fresh MOX fuel into the ocean on the routes of ocean transport from Europe to Japan. We calculated the concentration of 6 radionuclides ( 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu and 241 Am) over 1000 years. It takes 3.5 CPU hours for 1000-year calculation by the supercomputer HITACHI S3800. The concentration in the ocean due to the hypothetical submergence of a package of fresh MOX fuel is estimated to be much smaller than the present background concentration of fallout. (author)

  10. Maximum permissible dose

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    This chapter presents a historic overview of the establishment of radiation guidelines by various national and international agencies. The use of maximum permissible dose and maximum permissible body burden limits to derive working standards is discussed

  11. Hazards and maximum permissible doses of radiation for man

    International Nuclear Information System (INIS)

    Walinder, G.

    1977-11-01

    Maximum permissible dose levels are primarely based on risks for genetic damage and cancer. The reason for this is the observation that such late effects of radiation seem to arise even after doses that are to low to give rise to acute effects. In contrast to the tumour incidence found in irradiated human populations no genetic effects of radiation have been observed in man. This does not mean that genetic effects have not been induced but that it has been impossible to find an increase or to discern them among all the congenital defects, that can not be ascribed to the irradiation. As a consequence, the radiological risk estimation has been concentrated on the hazard of malignant diseases. Tumour risks are generally expressed as excess rates of incidence and mortality per million persons per rem. These figures are, however, not obtained from direct epidemiological observations but have been calculated from such data under the assumption of a linear relationship between effect and radiation dose. This formal extrapolation of observed data involves an uncertainty which, of course, is proportionately greater for the calculated effects in the millirem range. However, although the calculated tumour risks can not be said to be founded on direct scientific evidence, there are scientific reasons to believe that the figures derived from the formal extrapolations constitute an upper limit of possible ri02050

  12. Permission Marketing and Privacy Concerns - Why Do Customers (Not) Grant Permissions?

    NARCIS (Netherlands)

    Krafft, Manfred; Arden, Christine M.; Verhoef, Peter C.

    Little is known about the influence of motivators that drive consumers to grant permission to be contacted via personalized communication. In this study, a framework is developed to investigate the effect of select drivers of consumers granting permission to receive personalized messages. The

  13. MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2015. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-11-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  14. MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2014. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-11-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  15. MAK and BAT values list 2013. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2013. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-01

    The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2013 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

  16. Program for TI programmable 59 calculator for calculation of 3H concentration of water samples

    International Nuclear Information System (INIS)

    Hussain, S.D.; Asghar, G.

    1982-09-01

    A program has been developed for TI Programmable 59 Calculator of Texas Instruments Inc. to calculate from the observed parameters such as count rate etc. the 3 H (tritium) concentration of water samples processed with/without prior electrolytic enrichment. Procedure to use the program has been described in detail. A brief description of the laboratory treatment of samples and the mathematical equations used in the calculations have been given. (orig./A.B.)

  17. Take control of permissions in Leopard

    CERN Document Server

    Tanaka, Brian

    2009-01-01

    Permissions problems got you down? Turn to Unix expert Brian Tanaka's unique guide to the permissions in Mac OS X 10.5 Leopard that control access to your files, folders, and disks. You'll learn how to keep files private, when to set Ignore Permissions, what happens when you repair permissions, how to delete stuck files, and the best ways to solve permissions-related problems. Advanced concepts include the sticky bit, Leopard's more-important access control lists, bit masks, and symbolic versus absolute ways to set permissions. The book covers how to take control of permissions via the Finder

  18. Substantiation of the permissible radioactive contamination of working clothes

    International Nuclear Information System (INIS)

    Shcherbakov, V.L.; Korostin, A.S.

    1977-01-01

    A permissible level of working clothes contamination was determined on the base of the main migration routes of radioactive contaminants: permeation directly through the clothes into subclothes space on skin surface, emission into the air with amount of contaminants subsequently got by the organism of a working person through inhalation as well as transfer in the process of contacting of contaminated working clothes and surfaces of premises equipment, working person hands with amount of contaminants posteriorly got by the organism by alimentary or inhalation ways. Using the experimental and literature data available the permissible levels of working clothes contamination for the mentioned migration routes of radioactive materials have been calculated. According to the data obtained the permissible levels of working clothes contamination must not exceed 4 alpha-part/(cm 2 xmin) for contamination with high-tonic isotopes, 20 alpha-part./(cm 2 xmin) with other alpha-detine isotopes, 1000 beta-part./(cm 2 xmin) with beta-active ones. The permissible level of contamination of additional materials of the individual protection in the case of their contamination with high-tonic alpha-actine isotopes must not exceed 50 alpha-part./(cm 2 xmin), 200 alpha-part./(cm 2 xmin) for contamination th other alpha-active isotopes and 400 beta-part./(cm 2 xmin) with beta-active isotopes

  19. Concentration of Nitrate in Bottled Drinking Water in Qom, Iran

    Directory of Open Access Journals (Sweden)

    Mohammad Saberi Bidgoli

    2013-11-01

    Full Text Available Background & Aims of the Study: The global consumption of bottled water is growing with substantial growth in sales volumes on every continent. The highest growth rates are occurring in Asia and South America. Biological and chemical monitoring of these waters is necessary. The aim of current study was determination of nitrate concentration in bottled drinking water in Qom, Iran in 2012. Materials & Methods: A cross-sectional study carried out in Qom, Iran. First of all, 18 most frequent brands of bottled drinking waters were purchased in June 2012 randomly. Then concentration of nitrate was measured according to the spectrophotometric method. In next step, experiment data were analyzed by Excel Software and P value was obtained by statistical calculations. Finally data were comprised with written nitrate concentration on labels and recommended permissible values . Results: The median nitrate concentration was 2.1 mg/L with the minimum 0.8 mg/L and maximum 8.1 mg/L. In 66.7 % of the samples, the measured nitrate concentrations were less than the written nitrate concentrations and in 33.3% of samples, the nitrate concentration was higher. The statistical calculation proved the significant difference between the median of written nitrate concentration on the label and investigated nitrate concentration (P value > 0.05. Conclusions: It be concluded that the measured nitrate concentration in all of the water samples is below the recommended permissible level.

  20. Vegetation concentration and inventory of metals and radionuclides in the old F-area seepage basin, 904-49G

    International Nuclear Information System (INIS)

    Murphy, C.E. Jr.

    1994-01-01

    Measured concentrations of radionuclides and toxic metals are used to calculate the total inventory of in the vegetation growing on the Old F-Area Seepage Basin. Air concentrations and inhalation doses from exposure to smoke from burning the vegetation are calculated to evaluate the effect of open air burning. Radionuclide inventory is one order of magnitude (10 x) less than those necessary to produce a 1 mrem dose. Air concentrations of toxic metals are less than one third the permissible occupational dose

  1. Permissible Delay in Payments

    Directory of Open Access Journals (Sweden)

    Yung-Fu Huang

    2007-01-01

    Full Text Available The main purpose of this paper wants to investigate the optimal retailer's lot-sizing policy with two warehouses under partially permissible delay in payments within the economic order quantity (EOQ framework. In this paper, we want to extend that fully permissible delay in payments to the supplier would offer the retailer partially permissible delay in payments. That is, the retailer must make a partial payment to the supplier when the order is received. Then the retailer must pay off the remaining balance at the end of the permissible delay period. In addition, we want to add the assumption that the retailer's storage space is limited. That is, the retailer will rent the warehouse to store these exceeding items when the order quantity is larger than retailer's storage space. Under these conditions, we model the retailer's inventory system as a cost minimization problem to determine the retailer's optimal cycle time and optimal order quantity. Three theorems are developed to efficiently determine the optimal replenishment policy for the retailer. Finally, numerical examples are given to illustrate these theorems and obtained a lot of managerial insights.

  2. Calculation of critical concentrations of actinides in an infinite medium of silicon dioxide

    International Nuclear Information System (INIS)

    Okuno, Hiroshi; Sato, Shohei; Kawasaki, Hiromitsu

    2009-01-01

    The critical concentrations of actinides in metal-silicon-dioxide (SiO 2 ) and in metal-water (H 2 O) mixtures were calculated for 26 actinides including 233,235 U, 239,241 Pu, 242m Am, 243,245,247 Cm, and 249,251 Cf. The calculations were performed using the Monte Carlo neutron transport calculation code MCNP5 combined with the evaluated nuclear data library JENDL3.3. The results showed that the critical concentration of actinide in metal-SiO 2 mixtures was about 1/5 of that in metal-H 2 O mixtures for all the fissile nuclides investigated. The k ∞ 's of metal-SiO 2 and metal-H 2 O at one-half of the respective critical concentration of actinide, which was assumed as the subcritical concentration limit, were found to be less than 0.8 for all the actinides considered. By applying the sum-of-fractions rule to the concentrations of six nuclides in metal-SiO 2 mixtures, the subcriticality of high-level radioactive wastes was confirmed for a reported sample. The effects of different nuclear data libraries on the results of critical concentrations were found to be large for 242 Cm, 247 Cm, and 250 Cf by comparison with the results calculated with another evaluated nuclear data library, ENDF/B-VI. (author)

  3. Android Multi-Level System Permission Management Approach

    OpenAIRE

    Luo, Yang; Zhang, Qixun; Shen, Qingni; Liu, Hongzhi; Wu, Zhonghai

    2017-01-01

    With the expansion of the market share occupied by the Android platform, security issues (especially application security) have become attention focus of researchers. In fact, the existing methods lack the capabilities to manage application permissions without root privilege. This study proposes a dynamic management mechanism of Android application permissions based on security policies. The paper first describes the permissions by security policies, then implementes permission checking code ...

  4. Maximum permissible voltage of YBCO coated conductors

    Energy Technology Data Exchange (ETDEWEB)

    Wen, J.; Lin, B.; Sheng, J.; Xu, J.; Jin, Z. [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Hong, Z., E-mail: zhiyong.hong@sjtu.edu.cn [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Wang, D.; Zhou, H.; Shen, X.; Shen, C. [Qingpu Power Supply Company, State Grid Shanghai Municipal Electric Power Company, Shanghai (China)

    2014-06-15

    Highlights: • We examine three kinds of tapes’ maximum permissible voltage. • We examine the relationship between quenching duration and maximum permissible voltage. • Continuous I{sub c} degradations under repetitive quenching where tapes reaching maximum permissible voltage. • The relationship between maximum permissible voltage and resistance, temperature. - Abstract: Superconducting fault current limiter (SFCL) could reduce short circuit currents in electrical power system. One of the most important thing in developing SFCL is to find out the maximum permissible voltage of each limiting element. The maximum permissible voltage is defined as the maximum voltage per unit length at which the YBCO coated conductors (CC) do not suffer from critical current (I{sub c}) degradation or burnout. In this research, the time of quenching process is changed and voltage is raised until the I{sub c} degradation or burnout happens. YBCO coated conductors test in the experiment are from American superconductor (AMSC) and Shanghai Jiao Tong University (SJTU). Along with the quenching duration increasing, the maximum permissible voltage of CC decreases. When quenching duration is 100 ms, the maximum permissible of SJTU CC, 12 mm AMSC CC and 4 mm AMSC CC are 0.72 V/cm, 0.52 V/cm and 1.2 V/cm respectively. Based on the results of samples, the whole length of CCs used in the design of a SFCL can be determined.

  5. A revised method to calculate the concentration time integral of atmospheric pollutants

    International Nuclear Information System (INIS)

    Voelz, E.; Schultz, H.

    1980-01-01

    It is possible to calculate the spreading of a plume in the atmosphere under nonstationary and nonhomogeneous conditions by introducing the ''particle-in-cell'' method (PIC). This is a numerical method by which the transport of and the diffusion in the plume is reproduced in such a way, that particles representing the concentration are moved time step-wise in restricted regions (cells) and separately with the advection velocity and the diffusion velocity. This has a systematical advantage over the steady state Gaussian plume model usually used. The fixed-point concentration time integral is calculated directly instead of being substituted by the locally integrated concentration at a constant time as is done in the Gaussian model. In this way inaccuracies due to the above mentioned computational techniques may be avoided for short-time emissions, as may be seen by the fact that both integrals do not lead to the same results. Also the PIC method enables one to consider the height-dependent wind speed and its variations while the Gaussian model can be used only with averaged wind data. The concentration time integral calculated by the PIC method results in higher maximum values in shorter distances to the source. This is an effect often observed in measurements. (author)

  6. 30 CFR 62.130 - Permissible exposure level.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Permissible exposure level. 62.130 Section 62... REGULATIONS OCCUPATIONAL NOISE EXPOSURE § 62.130 Permissible exposure level. (a) The mine operator must assure that no miner is exposed during any work shift to noise that exceeds the permissible exposure level. If...

  7. OPT-TWO: Calculation code for two-dimensional MOX fuel models in the optimum concentration distribution

    International Nuclear Information System (INIS)

    Sato, Shohei; Okuno, Hiroshi; Sakai, Tomohiro

    2007-08-01

    OPT-TWO is a calculation code which calculates the optimum concentration distribution, i.e., the most conservative concentration distribution in the aspect of nuclear criticality safety, of MOX (mixed uranium and plutonium oxide) fuels in the two-dimensional system. To achieve the optimum concentration distribution, we apply the principle of flattened fuel importance distribution with which the fuel system has the highest reactivity. Based on this principle, OPT-TWO takes the following 3 calculation steps iteratively to achieve the optimum concentration distribution with flattened fuel importance: (1) the forward and adjoint neutron fluxes, and the neutron multiplication factor, with TWOTRAN code which is a two-dimensional neutron transport code based on the SN method, (2) the fuel importance, and (3) the quantity of the transferring fuel. In OPT-TWO, the components of MOX fuel are MOX powder, uranium dioxide powder and additive. This report describes the content of the calculation, the computational method, and the installation method of the OPT-TWO, and also describes the application method of the criticality calculation of OPT-TWO. (author)

  8. Methodology for calculating guideline concentrations for safety shot sites

    International Nuclear Information System (INIS)

    1997-06-01

    Residual plutonium (Pu), with trace quantities of depleted uranium (DU) or weapons grade uranium (WU), exists in surficial soils at the Nevada Test Site (NTS), Nellis Air Force Range (NAFR), and the Tonopah Test Range (TTR) as the result of the above-ground testing of nuclear weapons and special experiments involving the detonation of plutonium-bearing devices. The special experiments (referred to as safety shots) involving plutonium-bearing devices were conducted to study the behavior of Pu as it was being explosively compressed; ensure that the accidental detonation of the chemical explosive in a production weapon would not result in criticality; evaluate the ability of personnel to manage large-scale Pu dispersal accidents; and develop criteria for transportation and storage of nuclear weapons. These sites do not pose a health threat to either workers or the general public because they are under active institutional control. The DOE is committed to remediating the safety shot sites so that radiation exposure to the public, both now and in the future, will be maintained within the established limits and be as low as reasonably achievable. Remediation requires calculation of a guideline concentration for the Pu, U, and their decay products that are present in the surface soil. This document presents the methodology for calculating guideline concentrations of weapons grade plutonium, weapons grade uranium, and depleted uranium in surface soils at the safety shot sites. Emphasis is placed on obtaining site-specific data for use in calculating dose to potential residents from the residual soil contamination

  9. Methodology for calculating guideline concentrations for safety shot sites

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    Residual plutonium (Pu), with trace quantities of depleted uranium (DU) or weapons grade uranium (WU), exists in surficial soils at the Nevada Test Site (NTS), Nellis Air Force Range (NAFR), and the Tonopah Test Range (TTR) as the result of the above-ground testing of nuclear weapons and special experiments involving the detonation of plutonium-bearing devices. The special experiments (referred to as safety shots) involving plutonium-bearing devices were conducted to study the behavior of Pu as it was being explosively compressed; ensure that the accidental detonation of the chemical explosive in a production weapon would not result in criticality; evaluate the ability of personnel to manage large-scale Pu dispersal accidents; and develop criteria for transportation and storage of nuclear weapons. These sites do not pose a health threat to either workers or the general public because they are under active institutional control. The DOE is committed to remediating the safety shot sites so that radiation exposure to the public, both now and in the future, will be maintained within the established limits and be as low as reasonably achievable. Remediation requires calculation of a guideline concentration for the Pu, U, and their decay products that are present in the surface soil. This document presents the methodology for calculating guideline concentrations of weapons grade plutonium, weapons grade uranium, and depleted uranium in surface soils at the safety shot sites. Emphasis is placed on obtaining site-specific data for use in calculating dose to potential residents from the residual soil contamination.

  10. Permissiveness toward tobacco sponsorship undermines tobacco control support in Africa.

    Science.gov (United States)

    Ayo-Yusuf, Olalekan A; Olutola, Bukola G; Agaku, Israel T

    2016-06-01

    School personnel, who are respected members of the community, may exert significant influence on policy adoption. This study assessed the impact of school personnel's permissiveness toward tobacco industry sponsorship activities on their support for complete bans on tobacco advertisements, comprehensive smoke-free laws and increased tobacco prices. Representative data were obtained from the Global School Personnel Survey for 29 African countries (n = 17 929). Adjusted prevalence ratios (aPR) were calculated using multi-variable Poisson regression models to assess the impact of permissiveness toward tobacco sponsorship activities on support for tobacco control policies (p industry should be allowed to sponsor school events were significantly less likely to support complete bans on tobacco advertisements [aPR = 0.89; 95% confidence interval (CI) 0.84-0.95] and comprehensive smoke-free laws (aPR = 0.95; 95% CI 0.92-0.98). In contrast, support for complete tobacco advertisement bans was more likely among those who believed that the tobacco industry encourages youths to smoke (aPR = 1.27; 95% CI 1.17-1.37), and among those who taught about health sometimes (aPR = 1.06; 95% CI 1.01-1.11) or a lot (aPR = 1.05; 95% CI 1.01-1.10) compared with those who did not teach about health at all. These findings underscore the need to educate school personnel on tobacco industry's strategies to undermine tobacco control policies. This may help to build school personnel support for laws intended to reduce youth susceptibility, experimentation and established use of tobacco products. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  11. 12 CFR 703.14 - Permissible investments.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Permissible investments. 703.14 Section 703.14 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING CREDIT UNIONS INVESTMENT AND DEPOSIT ACTIVITIES § 703.14 Permissible investments. (a) Variable rate investment. A Federal...

  12. Study on calculation models and distribution rules of the radon concentration and its progenies concentration in blind roadway with forced-exhaust ventilation

    International Nuclear Information System (INIS)

    Ye Yongjun; Wang Liheng; Zhou Xinghuo; Li Xiangyang; Zhong Yongming; Wang Shuyun; Ding Dexin

    2014-01-01

    The forced-exhaust ventilation is an important way to control the concentration of radon and its progenies in long-distance blind driving roadway. It is of great significance for guiding the design of ventilation and radiation protection to study distribution characteristics of the concentration of radon and its progenies in the wind of roadway adopting the forced-exhaust ventilation. Therefore, according to the decay relationship of radon and its progenies, a simplified mathematical calculation model was built, which relates to the radon activity concentration and the potential alpha concentration of radon progenies. The paper also analyzed the sources of radon and its progenies in the limited space of the blind roadway. Then, based on the turbulence mass transfer theory of ventilation air flow, the paper established mathematical calculation models of distribution characteristics of the radon activity concentration and the potential alpha concentration of radon progenies in blind roadway with forced-exhaust ventilation, respectively. Finally, the paper applied the calculation models to a special blind roadway, and discussed the influence of the ventilation air inflow and the radon exhalation rate of rock wall on the distribution of radon concentration and the potential alpha concentration of radon progenies in the roadway. Meanwhile, some protective measurements were put forward to reduce the radiation dose of worker caused by radon and its progenies in the blind roadway. (authors)

  13. A concept of dynamic permission mechanism on android

    Science.gov (United States)

    Aron, Lukas; Hanacek, Petr

    2016-02-01

    This paper discuss the main security topic in mobile security area and this topic is protect user against the leakage of data. This work primarily contains the proposal of concept of dynamic permission mechanism for Android operating system. This mechanism deals with assignment or enforcement permissions to the application according to files that the application works with. Application has set of permissions that can use, but if the user opens confident files the application permissions should change its permission set and there should not be possible leakage of this secret data. The permissions set should be stricter according to opened confidential file or more open (without restriction) if the file is not secret file. The concept proposes the solution for protecting this data leakage. Idea covers rule that user should be avoided of change this permissions himself, but this behavior should be dynamic, automatic and independent. This proposal is mainly aimed to Android operating system, but the concept can be applied to other mobile platforms with some implementation changes.

  14. A single-blinded randomised clinical trial of permissive underfeeding in patients requiring parenteral nutrition.

    Science.gov (United States)

    Owais, Anwar Elias; Kabir, Syed Irfan; Mcnaught, Clare; Gatt, Marcel; MacFie, John

    2014-12-01

    The importance of adequate nutritional support is well established, but characterising what 'adequate nutrition' represents remains contentious. In recent years there has been increasing interest in the concept of 'permissive underfeeding' where patients are intentionally prescribed less nutrition than their calculated requirements. The aim of this study was to evaluate the effect of permissive underfeeding on septic and nutrition related morbidity in patients requiring short term parenteral nutrition (PN). This was a single-blinded randomised clinical trial of 50 consecutive patients requiring parenteral nutritional support. Patients were randomized to receive either normocaloric or hypocaloric feeding (respectively 100% vs. 60% of estimated requirements). The primary end point was septic complications. Secondary end points included the metabolic, physiological and clinical outcomes to the two feeding protocols. Permissive underfeeding was associated with fewer septic complications (3 vs. 12 patients; p = 0.003), and a lower incidence of the systemic inflammatory response syndrome (9 vs. 16 patients; p = 0.017). Permissively underfed patients had fewer feed related complications (2 vs. 9 patients; p = 0.016). Permissive underfeeding in patients requiring short term PN appears to be safe and may results in reduced septic and feed-related complications. NCT01154179 TRIAL REGISTRY: http://clinicaltrials.gov/ct2/show/NCT01154179. Copyright © 2014 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

  15. A dynamic model to calculate cadmium concentrations in bovine tissues from basic soil characteristics

    International Nuclear Information System (INIS)

    Waegeneers, Nadia; Ruttens, Ann; De Temmerman, Ludwig

    2011-01-01

    A chain model was developed to calculate the flow of cadmium from soil, drinking water and feed towards bovine tissues. The data used for model development were tissue Cd concentrations of 57 bovines and Cd concentrations in soil, feed and drinking water, sampled at the farms were the bovines were reared. Validation of the model occurred with a second set of measured tissue Cd concentrations of 93 bovines of which age and farm location were known. The exposure part of the chain model consists of two parts: (1) a soil-plant transfer model, deriving cadmium concentrations in feed from basic soil characteristics (pH and organic matter content) and soil Cd concentrations, and (2) bovine intake calculations, based on typical feed and water consumption patterns for cattle and Cd concentrations in feed and drinking water. The output of the exposure model is an animal-specific average daily Cd intake, which is then taken forward to a kinetic uptake model in which time-dependent Cd concentrations in bovine tissues are calculated. The chain model was able to account for 65%, 42% and 32% of the variation in observed kidney, liver and meat Cd concentrations in the validation study. - Research highlights: → Cadmium transfer from soil, drinking water and feed to bovine tissues was modeled. → The model was based on 57 bovines and corresponding feed and soil Cd concentrations. → The model was validated with an independent data set of 93 bovines. → The model explained 65% of variation in kidney Cd in the validation study.

  16. A method for calculation of dose per unit concentration values for aquatic biota

    International Nuclear Information System (INIS)

    Batlle, J Vives i; Jones, S R; Gomez-Ros, J M

    2004-01-01

    A dose per unit concentration database has been generated for application to ecosystem assessments within the FASSET framework. Organisms are represented by ellipsoids of appropriate dimensions, and the proportion of radiation absorbed within the organisms is calculated using a numerical method implemented in a series of spreadsheet-based programs. Energy-dependent absorbed fraction functions have been derived for calculating the total dose per unit concentration of radionuclides present in biota or in the media they inhabit. All radionuclides and reference organism dimensions defined within FASSET for marine and freshwater ecosystems are included. The methodology has been validated against more complex dosimetric models and compared with human dosimetry based on ICRP 72. Ecosystem assessments for aquatic biota within the FASSET framework can now be performed simply, once radionuclide concentrations in target organisms are known, either directly or indirectly by deduction from radionuclide concentrations in the surrounding medium

  17. Estimating permissible /sup 129/I-emission rates

    Energy Technology Data Exchange (ETDEWEB)

    Huebschmann, W G

    1976-06-01

    A mathematical method of iodine release limitation is presented which, in assessing the radiological effectiveness of /sup 129/I, takes advantage of the fact that the chemical behaviour of /sup 129/I resembles that of /sup 131/I and relies on the already extensive knowledge of the chemical and biological behaviour of /sup 131/I. If this method is used for calculating permissible /sup 129/I emission rates it is stated that no unnecessary restrictions need be imposed on a fuel reprocessing plant and that the grazing season for the pasture-cow-milk pathway can be taken into account. The concept is currently in use at the Karlsruhe Nuclear Research Center and seems to be appropriate for licensing of nuclear fuel reprocessing plants.

  18. MAK and BAT values list 2017. Maximum permissible concentrations at the place of work and biological tolerance values for working materials; MAK- und BAT-Werte-Liste 2017. Maximale Arbeitsplatzkonzentrationen und Biologische Arbeitsstofftoleranzwerte

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2017-08-01

    The MAK and BAT values list 2017 includes the maximum permissible concentrations at the place of work and biological tolerance values for working materials. The following working materials are covered: carcinogenic working materials, sensitizing materials and aerosols. The report discusses the restriction of exposure peaks, skin resorption, MAK (maximum working place concentration) values during pregnancy, germ cell mutagens and specific working materials. Importance and application of BAT (biological working material tolerance) values, list of materials, carcinogens, biological guide values and reference values are also included.

  19. Connection of automatic integral multichannel monitor of aerosol concentration

    International Nuclear Information System (INIS)

    Krejci, M.; Stulik, P.

    1985-01-01

    The instrument consists of the actual aerosol concentration monitor with two equivalent inputs, of an electropneumatic sampling selector, an aerosol pump, an electropneumatic valve, and of an exhaust device. For integral operating mode the instrument allows rapid checking and indication of exceedance of the permissible aerosol concentration limit at any sampling point. Upon exceedance of the permissible concentration limit, the device automatically switches into the multichannel cyclic measurement mode while the sampling point is identified where the aerosol concentration was increased. An emergency is displayed if the permissible limit has been exceeded. Following removal of the source of dangerous aerosol concentration, the control unit automatically switches the device into the integral measurement mode. (J.B.)

  20. Calculation of the isotope concentrations, source terms and radiation shielding of the SAFARI-1 irradiation products

    International Nuclear Information System (INIS)

    Stoker, C.C.; Ball, G.

    2000-01-01

    The ever increasing expansion of the irradiation product portfolio of the SAFARI-1 reactor leads to the need to routinely calculate the radio-isotope concentrations and source terms for the materials irradiated in the reactor accurately. In addition to this, the required shielding for the transportation and processing of these irradiation products needs to be determined. In this paper the calculational methodology applied is described with special attention given to the spectrum dependence of the one-group cross sections of selected SAFARI-1 irradiation materials and the consequent effect on the determination of the isotope concentrations and source terms. Comparisons of the calculated isotopic concentrations and dose rates with experimental analysis and measurements provide confidence in the calculational methodologies and data used. (author)

  1. Shell and Double Concentric Tube Heat Exchanger Calculations and Analysis

    Directory of Open Access Journals (Sweden)

    Basma Abbas Abdulmajeed

    2015-01-01

    Full Text Available This study concerns a new type of heat exchangers, which is that of shell-and-double concentric tube heat exchangers. The case studies include both design calculations and performance calculations. The new heat exchanger design was conducted according to Kern method. The volumetric flow rates were 3.6 m3/h and 7.63 m3/h for the hot oil and water respectively. The experimental parameters studied were: temperature, flow rate of hot oil, flow rate of cold water and pressure drop. A comparison was made for the theoretical and experimental results and it was found that the percentage error for the hot oil outlet temperature was (- 1.6%. The percentage errors for the pressure drop in the shell and in the concentric tubes were (17.2% and (- 39% respectively. For cold water outlet temperature, the percentage error was (- 3.3%, while it was (18% considering the pressure drop in the annulus formed. The percentage error for the total power consumed was (-10.8% A theoretical comparison was made between the new design and the conventional heat exchanger from the point of view of, length, mass, pressure drop and total power consumed.

  2. Osmotic potential calculations of inorganic and organic aqueous solutions over wide solute concentration levels and temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Cochrane, T. T., E-mail: agteca@hotmail.com [AGTECA S.A., 230 Oceanbeach Road, Mount Maunganui, Tauranga 3116 (New Zealand); Cochrane, T. A., E-mail: tom.cochrane@canterbury.ac.nz [Department of Civil and Natural Resources Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140 (New Zealand)

    2016-01-15

    Purpose: To demonstrate that the authors’ new “aqueous solution vs pure water” equation to calculate osmotic potential may be used to calculate the osmotic potentials of inorganic and organic aqueous solutions over wide ranges of solute concentrations and temperatures. Currently, the osmotic potentials of solutions used for medical purposes are calculated from equations based on the thermodynamics of the gas laws which are only accurate at low temperature and solute concentration levels. Some solutions used in medicine may need their osmotic potentials calculated more accurately to take into account solute concentrations and temperatures. Methods: The authors experimented with their new equation for calculating the osmotic potentials of inorganic and organic aqueous solutions up to and beyond body temperatures by adjusting three of its factors; (a) the volume property of pure water, (b) the number of “free” water molecules per unit volume of solution, “N{sub f},” and (c) the “t” factor expressing the cooperative structural relaxation time of pure water at given temperatures. Adequate information on the volume property of pure water at different temperatures is available in the literature. However, as little information on the relative densities of inorganic and organic solutions, respectively, at varying temperatures needed to calculate N{sub f} was available, provisional equations were formulated to approximate values. Those values together with tentative t values for different temperatures chosen from values calculated by different workers were substituted into the authors’ equation to demonstrate how osmotic potentials could be estimated over temperatures up to and beyond bodily temperatures. Results: The provisional equations formulated to calculate N{sub f}, the number of free water molecules per unit volume of inorganic and organic solute solutions, respectively, over wide concentration ranges compared well with the calculations of N{sub f

  3. Osmotic potential calculations of inorganic and organic aqueous solutions over wide solute concentration levels and temperatures

    International Nuclear Information System (INIS)

    Cochrane, T. T.; Cochrane, T. A.

    2016-01-01

    Purpose: To demonstrate that the authors’ new “aqueous solution vs pure water” equation to calculate osmotic potential may be used to calculate the osmotic potentials of inorganic and organic aqueous solutions over wide ranges of solute concentrations and temperatures. Currently, the osmotic potentials of solutions used for medical purposes are calculated from equations based on the thermodynamics of the gas laws which are only accurate at low temperature and solute concentration levels. Some solutions used in medicine may need their osmotic potentials calculated more accurately to take into account solute concentrations and temperatures. Methods: The authors experimented with their new equation for calculating the osmotic potentials of inorganic and organic aqueous solutions up to and beyond body temperatures by adjusting three of its factors; (a) the volume property of pure water, (b) the number of “free” water molecules per unit volume of solution, “N f ,” and (c) the “t” factor expressing the cooperative structural relaxation time of pure water at given temperatures. Adequate information on the volume property of pure water at different temperatures is available in the literature. However, as little information on the relative densities of inorganic and organic solutions, respectively, at varying temperatures needed to calculate N f was available, provisional equations were formulated to approximate values. Those values together with tentative t values for different temperatures chosen from values calculated by different workers were substituted into the authors’ equation to demonstrate how osmotic potentials could be estimated over temperatures up to and beyond bodily temperatures. Results: The provisional equations formulated to calculate N f , the number of free water molecules per unit volume of inorganic and organic solute solutions, respectively, over wide concentration ranges compared well with the calculations of N f using recorded

  4. A Symbolic Approach to Permission Accounting for Concurrent Reasoning

    NARCIS (Netherlands)

    Huisman, Marieke; Mostowski, Wojciech

    2015-01-01

    Permission accounting is fundamental to modular, thread-local reasoning about concurrent programs. This paper presents a new, symbolic system for permission accounting. In existing systems, permissions are numeric value-based and refer to the current thread only. Our system is based on symbolic

  5. A sensitivity study on neutron flux variation due to 10B concentration in dose calculation for BNCT

    International Nuclear Information System (INIS)

    Jung, Sang Hoon

    2006-02-01

    The effects of inclusion of 10 B concentration on neutron flux and dose in dose calculation were studied. In order to provide the quantitative effects of inclusion of 10 B concentrations on depressions of neutron and photon flux and dose, the fluxes and doses with voxel head phantoms for various 10 B concentrations homogeneously distributed were calculated by using MCNPX simulations. A lithium target system and beam shaping assembly, which have been developed at the Hanyang University, were used as epithermal neutron beam. The calculation results show that the neutron flux at the center of the head phantom decreases by approximately 5.4% per 10 ppm of 10 B concentration in comparison with the neutron flux in the case of boron-free. It was also observed that the tissue dose at the center of the head phantom is depressed by approximately 4.7% per 10 ppm of the 10 B concentration and the tumor dose by approximately 5.3% per 10 ppm. According to depth of tumors, it was observed that the depressions of the doses in the tumors are ranged in 3.7 ∼ 9.2%. The dose calculations in the case of boron-free show that it is overestimated in comparison with the dose calculations in the cases of the inclusion of 10 B concentrations for the normal tissue and the tumors. Therefore, in dose calculation for BNCT, the depressions of neutron flux and dose should be considered. The results in this study are available to setting up the depression ratios which can be used for converting neutron and gamma fluxes and doses in phantom with boron free into the fluxes and doses in phantom with inclusion of 10 B concentrations in treatment. It is expected that the depression ratios is practicable to dose evaluation for BNCT

  6. Practical method of calculating time-integrated concentrations at medium and large distances

    International Nuclear Information System (INIS)

    Cagnetti, P.; Ferrara, V.

    1980-01-01

    Previous reports have covered the possibility of calculating time-integrated concentrations (TICs) for a prolonged release, based on concentration estimates for a brief release. This study proposes a simple method of evaluating concentrations in the air at medium and large distances, for a brief release. It is known that the stability of the atmospheric layers close to ground level influence diffusion only over short distances. Beyond some tens of kilometers, as the pollutant cloud progressively reaches higher layers, diffusion is affected by factors other than the stability at ground level, such as wind shear for intermediate distances and the divergence and rotational motion of air masses towards the upper limit of the mesoscale and on the synoptic scale. Using the data available in the literature, expressions for sigmasub(y) and sigmasub(z) are proposed for transfer times corresponding to those for up to distances of several thousand kilometres, for two initial diffusion situations (up to distances of 10 - 20 km), those characterized by stable and neutral conditions respectively. Using this method simple hand calculations can be made for any problem relating to the diffusion of radioactive pollutants over long distances

  7. 14 CFR 399.35 - Special tariff permission.

    Science.gov (United States)

    2010-01-01

    ... PROCEEDINGS) POLICY STATEMENTS STATEMENTS OF GENERAL POLICY Policies Relating to Rates and Tariffs § 399.35 Special tariff permission. (a) Definition. As used in this section, to grant STP means to approve a... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Special tariff permission. 399.35 Section...

  8. Verification of average daily maximum permissible concentration of styrene in the atmospheric air of settlements under the results of epidemiological studies of the children’s population

    Directory of Open Access Journals (Sweden)

    М.А. Zemlyanova

    2015-03-01

    Full Text Available We presented the materials on the verification of the average daily maximum permissible concentration of styrene in the atmospheric air of settlements performed under the results of own in-depth epidemiological studies of children’s population according to the principles of the international risk assessment practice. It was established that children in the age of 4–7 years when exposed to styrene at the level above 1.2 of threshold level value for continuous exposure develop the negative exposure effects in the form of disorders of hormonal regulation, pigmentary exchange, antioxidative activity, cytolysis, immune reactivity and cytogenetic disbalance which contribute to the increased morbidity of diseases of the central nervous system, endocrine system, respiratory organs, digestion and skin. Based on the proved cause-and-effect relationships between the biomarkers of negative effects and styrene concentration in blood it was demonstrated that the benchmark styrene concentration in blood is 0.002 mg/dm3. The justified value complies with and confirms the average daily styrene concentration in the air of settlements at the level of 0.002 mg/m3 accepted in Russia which provides the safety for the health of population (1 threshold level value for continuous exposure.

  9. Exploring Permission-Induced Risk in Android Applications for Malicious Application Detection

    KAUST Repository

    Wang, Wei

    2014-10-07

    Android has been a major target of malicious applications (malapps). How to detect and keep the malapps out of the app markets is an ongoing challenge. One of the central design points of Android security mechanism is permission control that restricts the access of apps to core facilities of devices. However, it imparts a significant responsibility to the app developers with regard to accurately specifying the requested permissions and to the users with regard to fully understanding the risk of granting certain combinations of permissions. Android permissions requested by an app depict the app\\'s behavioral patterns. In order to help understanding Android permissions, in this paper, we explore the permission-induced risk in Android apps on three levels in a systematic manner. First, we thoroughly analyze the risk of an individual permission and the risk of a group of collaborative permissions. We employ three feature ranking methods, namely, mutual information, correlation coefficient, and T-test to rank Android individual permissions with respect to their risk. We then use sequential forward selection as well as principal component analysis to identify risky permission subsets. Second, we evaluate the usefulness of risky permissions for malapp detection with support vector machine, decision trees, as well as random forest. Third, we in depth analyze the detection results and discuss the feasibility as well as the limitations of malapp detection based on permission requests. We evaluate our methods on a very large official app set consisting of 310 926 benign apps and 4868 real-world malapps and on a third-party app sets. The empirical results show that our malapp detectors built on risky permissions give satisfied performance (a detection rate as 94.62% with a false positive rate as 0.6%), catch the malapps\\' essential patterns on violating permission access regulations, and are universally applicable to unknown malapps (detection rate as 74.03%).

  10. Is the maximum permissible radiation burden for the population indeed permissible

    International Nuclear Information System (INIS)

    Renesse, R.L. van.

    1975-01-01

    It is argued that legislation based on the ICRP doses will, under economical influences, lead to a situation where the population is exposed to radiation doses near the maximum permissible dose. Due to cumulative radiation effects, this will introduce unacceptable health risks. Therefore, it will be necessary to lower the legal dose limit of 170 millrem per year per person by a factor 10 to 20

  11. A simple method to estimate the optimum iodine concentration of contrast material through microcatheters: hydrodynamic calculation with spreadsheet software

    International Nuclear Information System (INIS)

    Yamauchi, Teiyu; Hayashi, Toshihiko; Yamada, Takeshi; Futami, Choichiro; Tsukiyama, Yumiko; Harada, Motoko; Furui, Shigeru; Suzuki, Shigeru; Mimura, Kohshiro

    2008-01-01

    It is important to increase the iodine delivery rate (I), that is the iodine concentration of the contrast material (C) x the flow rate of the contrast material (Q), through microcatheters to obtain arteriograms of the highest contrast. It is known that C is an important factor that influences I. The purpose of this study is to establish a method of hydrodynamic calculation of the optimum iodine concentration (i.e., the iodine concentration at which I becomes maximum) of the contrast material and its flow rate through commercially available microcatheters. Iopamidol, ioversol and iohexol of ten iodine concentrations were used. Iodine delivery rates (I meas) of each contrast material through ten microcatheters were measured. The calculated iodine delivery rate (I cal) and calculated optimum iodine concentration (calculated C opt) were obtained with spreadsheet software. The agreement between I cal and I meas was studied by correlation and logarithmic Bland-Altman analyses. The value of the calculated C opt was within the optimum range of iodine concentrations (i.e. the range of iodine concentrations at which I meas becomes 90% or more of the maximum) in all cases. A good correlation between I cal and I meas (I cal = 1.08 I meas, r = 0.99) was observed. Logarithmic Bland-Altman analysis showed that the 95% confidence interval of I cal/I meas was between 0.82 and 1.29. In conclusion, hydrodynamic calculation with spreadsheet software is an accurate, generally applicable and cost-saving method to estimate the value of the optimum iodine concentration and its flow rate through microcatheters

  12. Rethinking Permissioned Blockchains

    OpenAIRE

    Vukolic, Marko

    2017-01-01

    Current blockchain platforms, especially the recent permissioned systems, have architectural limitations: smart contracts run sequentially, all node executes all smart contracts, consensus protocols are hard-coded, the trust model is static and not exible, and non-determinism in smart-contract execution poses serious problems. Overcoming these limitations is critical for improving both functional properties of blockchains, such as con dentiality and consistency, as well as their non-functiona...

  13. A New Theory for Calculation of Some Biochemical Parameters Concentration in Human Serum

    International Nuclear Information System (INIS)

    Moustafa, K.A.; Amien, A.I.

    2009-01-01

    The serum volumes of the blood samples are varied from one patient to another according to the packed cell volume (PCV %), so if the patient sample has low PCV %, it will have high serum volume and vice versa. To calculate a certain clinical parameter such as glucose in the serum of patients using the conventional calculation, it will give the concentration in units per deci liter serum, while by calculating the concentration according to the ratio of serum volume to the total volume of the blood, it will give different results. Thus, the present study aimed to find a new theory used for calculation of some biochemical parameters concentration taking into consideration the ratio of plasma volume to the total blood volume. The present study was conducted on 122 subjects. These subjects were categorized into 4 groups. Group 1 (G1) comprised 40 healthy subjects as control group, group 2 (G2) comprised 30 low PCV % patients, group 3 (G3) comprised 30 subjects with relatively high PCV % and group 4 comprised 22 diabetic patients. Each group of the previous groups was further subdivided into group a (G a ) and group b (G b ). In the later group, the results were multiplied by the correction factor (V p /V b ), which is the ratio of plasma volume (V p ) to the blood volume (V b ) TSH hormone, glucose, cholesterol, triglycerides, urea, creatinine, uric acid, alanine aminotransferase (ALT), aspartate transaminase (AST) and alkaline phosphatase (ALP) were estimated and the results were multiplied by the correction factor (V p /V b ) to get the results after correction. Compared the results before and after correction, there was a very highly significant (ρ p /V b ), thus we recommended that biochemical parameters results must be calculated as indicated in the present study to obtain actual results which might be useful in the correct diagnosis, monitoring and follow up of the different diseases

  14. Model for calculation of concentration and load on behalf of accidents with radioactive materials

    International Nuclear Information System (INIS)

    Janssen, L.A.M.; Heugten, W.H.H. van

    1987-04-01

    In the project 'Information- and calculation-system for disaster combatment', by order of the Dutch government, a demonstration model has been developed for a diagnosis system for accidents. In this demonstration a model is used to calculate the concentration- and dose-distributions caused by incidental emissions of limited time. This model is described in this report. 4 refs.; 2 figs.; 3 tabs

  15. 42 CFR 433.66 - Permissible provider-related donations.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Permissible provider-related donations. 433.66... Requirements State Financial Participation § 433.66 Permissible provider-related donations. (a) General rule... provider-related donations without a reduction in FFP, only in accordance with the requirements of this...

  16. Can ‘Mobile Platform’ and ‘Permission Marketing’ dance a tango to the consumers' tune? Modeling adoption of ‘SMS based Permission Advertising’

    OpenAIRE

    Prerna Bamoriya

    2015-01-01

    Many a times situation of advertising clutter is further aggrieved by the markers’ intrusive practices i.e. not asking for consumer’s explicit permission. It results in consumers’ alienation and reduced advertising effectiveness. Solution could be integration of Permission Marketing with an innovative advertising platform like Mobile. This study aimed to develop and validate a comprehensive model for understanding consumers’ adoption behavior towards SMS Based Permission Advertising (SBPA). F...

  17. Quantitative Security Risk Assessment of Android Permissions and Applications

    OpenAIRE

    Wang , Yang; Zheng , Jun; Sun , Chen; Mukkamala , Srinivas

    2013-01-01

    Part 6: Mobile Computing; International audience; The booming of the Android platform in recent years has attracted the attention of malware developers. However, the permissions-based model used in Android system to prevent the spread of malware, has shown to be ineffective. In this paper, we propose DroidRisk, a framework for quantitative security risk assessment of both Android permissions and applications (apps) based on permission request patterns from benign apps and malware, which aims ...

  18. Immunotoxicity of perfluorinated alkylates: calculation of benchmark doses based on serum concentrations in children

    DEFF Research Database (Denmark)

    Grandjean, Philippe; Budtz-Joergensen, Esben

    2013-01-01

    BACKGROUND: Immune suppression may be a critical effect associated with exposure to perfluorinated compounds (PFCs), as indicated by recent data on vaccine antibody responses in children. Therefore, this information may be crucial when deciding on exposure limits. METHODS: Results obtained from...... follow-up of a Faroese birth cohort were used. Serum-PFC concentrations were measured at age 5 years, and serum antibody concentrations against tetanus and diphtheria toxoids were obtained at ages 7 years. Benchmark dose results were calculated in terms of serum concentrations for 431 children...

  19. Android Permission Model

    OpenAIRE

    Birendra, Chalise

    2016-01-01

    The recent evolution on the smart phone technology has made its application market huge and less secure. Every single day large number of apps introduced in the android market (mostly on google play store) without any particular inspections which creates a lot of security issues and they remain unresolved. There are a lot of recent and increasing security issues which are mostly caused by the android apps. Mainly, the access of user data through the apps relied on the users given permission t...

  20. Calculation and evaluation of sediment effect concentrations for the amphipod Hyalella azteca and the midge Chironomus riparius

    Science.gov (United States)

    Ingersoll, Christopher G.; Haverland, Pamela S.; Brunson, Eric L.; Canfield, Timothy J.; Dwyer, F. James; Henke, Chris; Kemble, Nile E.; Mount, David R.; Fox, Richard G.

    1996-01-01

    Procedures are described for calculating and evaluating sediment effect concentrations (SECs) using laboratory data on the toxicity of contaminants associated with field-collected sediment to the amphipod Hyalella azteca and the midge Chironomus riparius. SECs are defined as the concentrations of individual contaminants in sediment below which toxicity is rarely observed and above which toxicity is frequently observed. The objective of the present study was to develop SECs to classify toxicity data for Great Lake sediment samples tested with Hyalella azteca and Chironomus riparius. This SEC database included samples from additional sites across the United States in order to make the database as robust as possible. Three types of SECs were calculated from these data: (1) Effect Range Low (ERL) and Effect Range Median (ERM), (2) Threshold Effect Level (TEL) and Probable Effect Level (PEL), and (3) No Effect Concentration (NEC). We were able to calculate SECs primarily for total metals, simultaneously extracted metals, polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs). The ranges of concentrations in sediment were too narrow in our database to adequately evaluate SECs for butyltins, methyl mercury, polychlorinated dioxins and furans, or chlorinated pesticides. About 60 to 80% of the sediment samples in the database are correctly classified as toxic or not toxic depending on type of SEC evaluated. ERMs and ERLs are generally as reliable as paired PELs and TELs at classifying both toxic and non-toxic samples in our database. Reliability of the SECs in terms of correctly classifying sediment samples is similar between ERMs and NECs; however, ERMs minimize Type I error (false positives) relative to ERLs and minimize Type II error (false negatives) relative to NECs. Correct classification of samples can be improved by using only the most reliable individual SECs for chemicals (i.e., those with a higher percentage of correct classification). SECs

  1. Maximum permissible body burdens and maximum permissible concentrations of radionuclides in air and in water for occupational exposure. Recommendations of the National Committee on Radiation Protection. Handbook 69

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1959-06-05

    The present Handbook and its predecessors stem from the Second International Congress of Radiology, held in Stockholm in 1928. At that time, under the auspices of the Congress, the International Commission on Radiological Protection (ICRP) was organized to deal initially with problems of X-ray protection and later with radioactivity protection. At that time 'permissible' doses of X-rays were estimated primarily in terms of exposures which produced erythema, the amount of exposure which would produce a defined reddening of the skin. Obviously a critical problem in establishing criteria for radiation protection was one of developing useful standards and techniques of physical measurement. For this reason two of the organizations in this country with a major concern for X-ray protection, the American Roentgen Ray Society and the Radiology Society of North America, suggested that the National Bureau of Standards assume responsibility for organizing representative experts to deal with the problem. Accordingly, early in 1929, an Advisory Committee on X-ray and Radium Protection was organized to develop recommendations on the protection problem within the United States and to formulate United States points of view for presentation to the International Commission on Radiological Protection. The organization of the U.S. Advisory Committee included experts from both the medical and physical science fields. The recommendations of this Handbook take into consideration the NCRP statement entitled 'Maximum Permissible Radiation Exposures to Man', published as an addendum to Handbook 59 on April 15, 1958. As noted above this study was carried out jointly by the ICRP and the NCRP, and the complete report is more extensive than the material contained in this Handbook.

  2. Maximum permissible body burdens and maximum permissible concentrations of radionuclides in air and in water for occupational exposure. Recommendations of the National Committee on Radiation Protection. Handbook 69

    International Nuclear Information System (INIS)

    1959-01-01

    The present Handbook and its predecessors stem from the Second International Congress of Radiology, held in Stockholm in 1928. At that time, under the auspices of the Congress, the International Commission on Radiological Protection (ICRP) was organized to deal initially with problems of X-ray protection and later with radioactivity protection. At that time 'permissible' doses of X-rays were estimated primarily in terms of exposures which produced erythema, the amount of exposure which would produce a defined reddening of the skin. Obviously a critical problem in establishing criteria for radiation protection was one of developing useful standards and techniques of physical measurement. For this reason two of the organizations in this country with a major concern for X-ray protection, the American Roentgen Ray Society and the Radiology Society of North America, suggested that the National Bureau of Standards assume responsibility for organizing representative experts to deal with the problem. Accordingly, early in 1929, an Advisory Committee on X-ray and Radium Protection was organized to develop recommendations on the protection problem within the United States and to formulate United States points of view for presentation to the International Commission on Radiological Protection. The organization of the U.S. Advisory Committee included experts from both the medical and physical science fields. The recommendations of this Handbook take into consideration the NCRP statement entitled 'Maximum Permissible Radiation Exposures to Man', published as an addendum to Handbook 59 on April 15, 1958. As noted above this study was carried out jointly by the ICRP and the NCRP, and the complete report is more extensive than the material contained in this Handbook

  3. Control over Permissible Short Emergency Overloads in Power Transformers

    Directory of Open Access Journals (Sweden)

    V. A. Anischenko

    2010-01-01

    Full Text Available The paper proposes a method for determination a permissible duration of short intermittent overloads of power transformers that permits to avoid non-permissible over-heating of winding insulation and fully utilize overloading transformer ability.

  4. Efficiency of individual dosage of digoxin with calculated concentration

    Directory of Open Access Journals (Sweden)

    Zhao L

    2014-07-01

    Full Text Available Li Zhao,1,* Peng Yang,2,* Pengmei Li,1 Xiaoxing Wang,1 Wangjun Qin,1 Xianglin Zhang1 1Department of Pharmacy, 2Department of Cardiology, China-Japan Friendship Hospital, Beijing, People’s Republic of China *These authors contributed equally to this work Background: Digoxin is a frequently prescribed drug, particularly in the elderly population, in which there is an increased prevalence of atrial fibrillation and cardiac failure. With its complex pharmacokinetic profile and narrow therapeutic index, use of digoxin requires regular monitoring of blood levels. Recent evidence suggests that a lower concentration range (0.4–1.0 ng/mL is preferable in patients with congestive heart failure and a higher range (0.8–2.0 ng/mL is needed in patients with atrial tachyarrhythmia. The Konishi equation is widely used to predict the serum digoxin concentration (SDC in Japan. This study assessed the correlation between SDC predicted by the Konishi equation and that actually measured in Chinese patients and investigated the impact of renal function on SDC. Methods: The study subjects comprised 72 patients with cardiac failure or/and atrial tachyarrhythmia seen at our hospital from January 2012 to December 2013. The patients were divided into five groups according to Kidney Diseases Outcome Quality Initiative guidelines. SDCs were measured using the Abbott Architect i1000 immunology analyzer. The correlations between measured SDCs and calculated SDCs and between clearance of digoxin and creatinine clearance rate were assessed retrospectively.Results: The correlation between measured and predicted SDC calculated by the Konishi equation was significant (r=0.655, P<0.001 for the 72 patients overall; however, correlations within the different stages of renal function were nonsignificant, with a correlation found only in patients with stage 3 (30 mL per minute < creatinine clearance <60 mL per minute. With regard to the correlation between clearance of

  5. Determination of the longest permissible distance between expansion compensators in gas transmission pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Huening, R [Fachhochschule Muenster, Burgsteinfurt (Germany, F.R.). Fachbereich Versorgungstechnik

    1977-01-01

    In order to effectively protect long-distance gas pipelines against mountain damage in the areas in which underground mining is done, expansion compensators must be built in at certain distances. The tests to determine the slippage resistance and the highest permissible distance of expanders Lsub(max) in a transmission line NW 600 having a plastic insulation are described in this work. In addition, a way of calculating the Lsub(max) value from the existing data for pipes of varying diameter and different insulating material is shown.

  6. Is the publication of exit poll results morally permissible?

    DEFF Research Database (Denmark)

    Sønderholm, Jørn

    2016-01-01

    This article is about exit polls. It addresses the question of whether or not it is morally permissible to publish exit poll results. The conclusion of the article is that an affirmative answer should be given to this question. In section 2, the master argument in favor of the moral permissibility...... of the publication of exit poll results is introduced. This is a strong argument. It is, however, argued that it might be the case that the conclusion of this argument should be rejected if there are other, and weightier, arguments against the idea that the publication of exit poll results is morally permissible....... In section 3, the strongest arguments against the moral permissibility of the publication of exit poll results are outlined and discussed. The conclusion of this section is that all these arguments fail in their intended purpose. The conclusion of the article is therefore justified....

  7. 45 CFR 1639.4 - Permissible representation of eligible clients.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Permissible representation of eligible clients... CORPORATION WELFARE REFORM § 1639.4 Permissible representation of eligible clients. Recipients may represent an individual eligible client who is seeking specific relief from a welfare agency. [62 FR 30766...

  8. Calculation Of Radon Gas Inhaled By A Front End Worker Of The Nuclear Fuel Cycles

    International Nuclear Information System (INIS)

    Soedardjo

    1996-01-01

    The calculation of Radon gas inhaled by workers in a front end nuclear fuel cycle has been studied. The cycle of front end nuclear fuel is underground uranium exploration on Remaja tunnel West Kalimantan. The activities of mining consider of drilling, blasting, transporting mineral and tunnel supporting were chosen, It is assumed that in one month, for a worker has four assignments namely in tunnel I, tunnel II, tunnel III and tunnel IV, The activities in the mine are divided into some categories, namely 12 hours of drilling, 2 hours of after blasting, 9 hours of mineral transportation and 8 hours of tunnel support construction. The result of calculation shows that the average Radon gas concentration on each particular location is still less than maximum permissible concentration 300 pCi/l. The prediction of maximum dose inhaled by one uranium miner during a year is 2.3 x 10 2 μCi which is less than BATAN regulation 7.3 x 10 2 μCi

  9. 46 CFR 115.700 - Permission for repairs and alterations.

    Science.gov (United States)

    2010-10-01

    ... replacement in kind, of electrical wiring, fuel lines, tanks, boilers and other pressure vessels, and steering... 46 Shipping 4 2010-10-01 2010-10-01 false Permission for repairs and alterations. 115.700 Section... AND CERTIFICATION Repairs and Alterations § 115.700 Permission for repairs and alterations. (a...

  10. 46 CFR 176.700 - Permission for repairs and alterations.

    Science.gov (United States)

    2010-10-01

    ... repair or replacement, other than replacement in kind, of electrical wiring, fuel lines, tanks, boilers... 46 Shipping 7 2010-10-01 2010-10-01 false Permission for repairs and alterations. 176.700 Section... (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Repairs and Alterations § 176.700 Permission for...

  11. User-centric android flexible permissions

    NARCIS (Netherlands)

    Scoccia, Gian Luca; Malavolta, Ivano; Autili, Marco; Di Salle, Amleto; Inverardi, Paola

    2017-01-01

    Privacy in mobile apps is a fundamental aspect to be considered, particularly with regard to meeting end user expectations. Due to the rigidities of the Android permission model, desirable trade-offs are not allowed. End users are confined into a secondary role, having the only option of choosing

  12. The levels of heavy metals in water and all aquatic in Ismailia canal, (Egypt) compared with the international permissible limits and accumulative studies for these metals in biota

    International Nuclear Information System (INIS)

    Saleh, H.M.; Moloukhia, H.; Belacy, N.; Abd El-Rahman, G.A.

    2011-01-01

    The concentration of Pb, Cd, Cu, Zu, Ni, Fe and Mn were determined in water, and in different organs of fishes, bivalves, snails and plants in Ismailia canal, Egypt. Moreover, accumulation of the investigated heavy metals by aquatic biota in Ismailia canal and the concentration factor values for this accumulation were calculated to qualify the degree of pollution and compare these levels with the international permissible limits. Results showed that Pb, Cd, Cu and Zn were exceeded the permissible limits especially in the industrial area of Abu- Zaabal, Kalubia governorate. The relative order of heavy metal levels in the canal water was: Fe>Mn>Pb>Zn>Ni>Cd>Cu.Accumulation of heavy metals by the aquatic biota was determined. The accumulation of heavy metals by common snails, namely physa acuta and biomphalaria alexandrina and the bivalve oyster Caelatura (caelatura) companyoi was found mainly in the edible parts (soft parts), whereas, the accumulation by their shells, which are mainly formed of calcium carbonate was via adsorption and surface complexation, since all the accumulated heavy metals were released by adding 0.1 M HCl for few minutes . Moreover, accumulation of heavy metals by common plants namely water hyacinth plant (Eichhornia crassipes) and freshwater weeds were determined. It was found that the accumulation of heavy metals was higher in roots than in leaves. On the other hand, the accumulation of heavy metals by common fish namely, Oreochromis niloticus (Nile Tilapia) was measured in its organs : muscles, liver, gills and gonads. It was found that there is variation of distribution of heavy metals among fish organs. Since the high accumulation of heavy metals among the investigated biota, they can be used as biological indicator for pollution of heavy metals in aquatic ecosystem . The average values and standard deviation for all measurements were determined. Data obtained were compared with the permissible concentrations of the environmental protection

  13. Non-Newtonian flow between concentric cylinders calculated from thermophysical properties obtained from simulations

    International Nuclear Information System (INIS)

    Narayan, A.P.; Rainwater, J.C.; Hanley, H.J.M.

    1995-01-01

    A study of the Weissenberg effect (rod climbing in a stirred system) based on nonequilibrium molecular dynamics (NEMD) is reported. Simulation results from a soft-sphere fluid are used to obtain a self-consistent free-surface profile of the fluid of finite compressibility undergoing Couette flow between concentric cylinders. A numerical procedure is then applied to calculate the height profile for a hypothetical fluid with thermophysical properties of the soft-sphere liquid and of a dense colloidal suspension. The height profile calculated is identified with shear thickening and the forms of the viscometric functions. The maximum climb occurs between the cylinders rather than at the inner cylinder

  14. Simulating Osmotic Equilibria: A New Tool for Calculating Activity Coefficients in Concentrated Aqueous Salt Solutions.

    Science.gov (United States)

    Bley, Michael; Duvail, Magali; Guilbaud, Philippe; Dufrêche, Jean-François

    2017-10-19

    Herein, a new theoretical method is presented for predicting osmotic equilibria and activities, where a bulk liquid and its corresponding vapor phase are simulated by means of molecular dynamics using explicit polarization. Calculated time-averaged number density profiles provide the amount of evaporated molecules present in the vapor phase and consequently the vapor-phase density. The activity of the solvent and the corresponding osmotic coefficient are determined by the vapor density at different solute concentrations with respect to the reference vapor density of the pure solvent. With the extended Debye-Hückel equation for the activity coefficient along with the corresponding Gibbs-Duhem relation, the activity coefficients of the solutes are calculated by fitting the osmotic coefficients. A simple model based on the combination of Poisson processes and Maxwell-Boltzmann velocity distributions is introduced to interpret statistical phenomena observed during the simulations, which are related to evaporation and recondensation. This method is applied to aqueous dysprosium nitrate [Dy(NO 3 ) 3 ] solutions at different concentrations. The obtained densities of the liquid bulk and the osmotic and activity coefficients are in good agreement with the experimental results for concentrated and saturated solutions. Density profiles of the liquid-vapor interface at different concentrations provide detailed insight into the spatial distributions of all compounds.

  15. Estimation and justification of permissible levels of Sr 90 in firewood and timber produced on the territories contaminated after the Chernobyl NPP accident

    International Nuclear Information System (INIS)

    Zabrodskij, V.N.; Bondar', Yu.I.; Sadchikov, V.I.; Kalinin, V.N.

    2014-01-01

    The permissible levels of Sr 90 in firewood and timber produced on the radioactively contaminated territory are calculated and justified. They are proposed to be used on the territories contaminated after the Chernobyl accident. (authors)

  16. Can ‘Mobile Platform’ and ‘Permission Marketing’ dance a tango to the consumers' tune? Modeling adoption of ‘SMS based Permission Advertising’

    Directory of Open Access Journals (Sweden)

    Prerna Bamoriya

    2015-12-01

    Full Text Available Many a times situation of advertising clutter is further aggrieved by the markers’ intrusive practices i.e. not asking for consumer’s explicit permission. It results in consumers’ alienation and reduced advertising effectiveness. Solution could be integration of Permission Marketing with an innovative advertising platform like Mobile. This study aimed to develop and validate a comprehensive model for understanding consumers’ adoption behavior towards SMS Based Permission Advertising (SBPA. For this, data was collected using systematic random sampling from 524 respondents and was analyzed using Structural Equation Modeling. Study revealed some critical variables along with complex relationships among such variables, in form of an empirically validated model. At last, study made some important implications for practitioners and researchers.

  17. The link between maternal sleep and permissive parenting during late adolescence.

    Science.gov (United States)

    Tu, Kelly M; Elmore-Staton, Lori; Buckhalt, Joseph A; El-Sheikh, Mona

    2018-03-05

    Utilizing a multi-method design, the present study examined the association between maternal sleep, assessed via actigraphy and self-reports, and permissive parenting (e.g. lax, inconsistent discipline) during adolescence, as well as the extent to which this association differed by mothers' race/ethnicity and socioeconomic status. The sample was comprised of 234 mothers (M age = 41.76 years, SD = 6.25; 67% European-American, 31% African-American, 2% other race/ethnicities) and 237 adolescents (113 boys, 124 girls; M age = 15.80 years, SD = 0.80; 66% European-American, 34% African-American). Mothers' sleep duration (actual sleep minutes) and quality (sleep efficiency, latency, long wake episodes) were assessed using actigraphy. Mothers also reported on their sleep problems and adolescents reported on mothers' permissive parenting behaviours. Results revealed that actigraphy-based longer sleep duration and shorter sleep latency were associated with lower levels of permissive parenting. Further, mothers' race/ethnicity and socioeconomic status moderated the association between actigraphy-based sleep quality (i.e. sleep efficiency, long wake episodes) and permissive parenting. Specifically, a negative association between sleep efficiency and permissive parenting was evident only for African-American mothers. In addition, a positive association between more frequent night wakings and permissive parenting was evident only for mothers from lower socioeconomic status households. The findings highlight the benefits of longer and higher-quality sleep for reducing the risk of permissive parenting, especially among ethnic minority mothers and mothers from lower socioeconomic status households. © 2018 European Sleep Research Society.

  18. May I sleep in your bed? Getting permission to book

    NARCIS (Netherlands)

    Karlsson, L.; Kemperman, A.D.A.M.; Dolnicar, S.

    2017-01-01

    Demand for tourist accommodation offered on peer-to-peer networks is skyrocketing. In such networks tourists can only book if the accommodation provider (host) gives their permission. Needing permission to book accommodation is radically new in tourism. No hotel, motel or B&B assesses a tourist

  19. Rationalizing the Permissibility of Mosque Decoration

    Directory of Open Access Journals (Sweden)

    Spahic Omer

    2016-06-01

    Full Text Available This paper discusses the subject of mosque decoration and some of the criteria which determine its permissibility or otherwise. Some aspects of the matter are somewhat sensitive and double-edged. Thus, the paper presents an objective, balanced and scientific account of the theme, steering clear of the sentimental aspects of the evidences often put forth by both the proponents and opponents of mosque decoration. The main thrusts of the paper are the issues pertaining to the legitimacy of decoration in general, the subject of the function of mosques vis-à-vis their decoration, as well as the broad guidelines that regulate mosque decoration emphasizing the decoration of the mihrab (praying niche area and the qiblah wall. The paper concludes that in principle mosque decoration is permissible so long as it conforms to the requirements of the Islamic spirituality and the quintessence of genuine Islamic art and architecture.

  20. Ways of solving the problem of NPP evaporate concentrate storage

    International Nuclear Information System (INIS)

    Dmitriev, S.A.; Lifanov, F.A.; Savkin, A.E.; Lashchenov, S.M.

    2000-01-01

    The use of next engineering operations: isotope separation using oxidation, filtration and selective sorption methods, hardening and long term secondary radioactive waste disposal (cement compound from filtration stage and depleted sorbent on filters); concentration and preparation of dry salts from the radionuclide-free stillage residues were proposed for NPP waste reprocessing. The laboratory and pilot tests that demonstrated the possibility for purification of NPP stillage residues from radionuclides to the levels less than maximum permissible ones were conducted. The purified stillage residues are sent for the burial after drying. The calculations of material flows are treated by the example of the Kursk NPP stillage residue and the scheme of the waste retrieval is given [ru

  1. FOOD II: an interactive code for calculating concentrations of radionuclides in food products

    International Nuclear Information System (INIS)

    Zach, R.

    1978-11-01

    An interactive code, FOOD II, has been written in FORTRAN IV for the PDP 10 to allow calculation of concentrations of radionuclides in food products and internal doses to man under chronic release conditions. FOOD II uses models unchanged from a previous code, FOOD, developed at Battelle, Pacific Northwest Laboratories. The new code has different input and output features than FOOD and a number of options have been added to increase flexibility. Data files have also been updated. FOOD II takes into account contamination of vegetation by air and irrigation water containing radionuclides. Contamination can occur simultaneously by air and water. Both direct deposition of radionuclides on leaves, and their uptake from soil are possible. Also, animals may be contaminated by ingestion of vegetation and drinking water containing radionuclides. At present, FOOD II provides selection of 14 food types, 13 diets and numerous radionuclides. Provisions have been made to expand all of these categories. Six additional contaminated food products can also be entered directly into the dose model. Doses may be calculated for the total body and six internal organs. Summaries of concentrations in food products and internal doses to man can be displayed at a local terminal or at an auxiliary high-speed printer. (author)

  2. Method for calculating ionic and electronic defect concentrations in y-stabilised zirconia

    Energy Technology Data Exchange (ETDEWEB)

    Poulsen, F W [Risoe National Lab., Materials Research Dept., Roskilde (Denmark)

    1997-10-01

    A numerical (trial and error) method for calculation of concentration of ions, vacancies and ionic and electronic defects in solids (Brouwer-type diagrams) is presented. No approximations or truncations of the set of equations describing the chemistry for the various defect regions are used. Doped zirconia and doped thoria with simultaneous presence of protonic and electronic defects are taken as examples: 7 concentrations as function of oxygen partial pressure and/or water vapour partial pressure are determined. Realistic values for the equilibrium constants for equilibration with oxygen gas and water vapour, as well as for the internal equilibrium between holes and electrons were taken from the literature. The present mathematical method is versatile - it has also been employed by the author to treat more complex systems, such as perovskite structure oxides with over- and under-stoichiometry in oxygen, cation vacancies and simultaneous presence of protons. (au) 6 refs.

  3. Permissive Subsorted Partial Logic in CASL

    DEFF Research Database (Denmark)

    Cerioli, Maura; Haxthausen, Anne Elisabeth; Krieg-Brückner, Bernd

    1997-01-01

    This paper presents a permissive subsorted partial logic used in the CoFI Algebraic Specification Language. In contrast to other order-sorted logics, subsorting is not modeled by set inclusions, but by injective embeddings allowing for more general models in which subtypes can have different data...

  4. Permissive hypercapnia and risk for brain injury and developmental impairment.

    Science.gov (United States)

    Hagen, Erika W; Sadek-Badawi, Mona; Carlton, David P; Palta, Mari

    2008-09-01

    Permissive hypercapnia is a respiratory-care strategy that is used to reduce the risk for lung injury. The goal of this study was to evaluate whether permissive hypercapnia is associated with higher risk for intraventricular hemorrhage and early childhood behavioral and functional problems than normocapnia among very low birth weight infants. Very low birth weight infants from a statewide cohort were eligible for this study when they were born at <32 weeks' gestational age and survived at least 24 hours. Infants were classified as receiving a permissive hypercapnia, normocapnia, or unclassifiable respiratory strategy during the first 24 hours after birth according to an algorithm based on Pco(2) values and respiratory-treatment decisions that were abstracted from medical charts. Intraventricular hemorrhage diagnosis was also abstracted from the medical chart. Behavioral and functional outcomes were assessed by parent interview at 2 to 3 years. Logistic regression was used to evaluate the relationship between intraventricular hemorrhage and respiratory strategy; ordinary linear regression was used to evaluate differences in behavior and function scores between children by respiratory strategy. Infants who received a permissive hypercapnia strategy were not more likely to have intraventricular hemorrhage than those with normocapnia. There were no differences in any of the behavioral or functional scores among children according to respiratory strategy. There was a significant interaction between care strategy and 1-minute Apgar score, indicating that infants with lower Apgar scores may be at higher risk for intraventricular hemorrhage with permissive hypercapnia. This study suggests that permissive hypercapnia does not increase risk for brain injury and impairment among very low birth weight children. The interaction between respiratory strategy and Apgar score is a potential worrisome exception to this conclusion. Future research should further evaluate the effect

  5. Effect of germanium concentrations on tunnelling current calculation of Si/Si1-xGex/Si heterojunction bipolar transistor

    Science.gov (United States)

    Hasanah, L.; Suhendi, E.; Khairrurijal

    2018-05-01

    Tunelling current calculation on Si/Si1-xGex/Si heterojunction bipolar transistor was carried out by including the coupling between transversal and longitudinal components of electron motion. The calculation results indicated that the coupling between kinetic energy in parallel and perpendicular to S1-xGex barrier surface affected tunneling current significantly when electron velocity was faster than 1x105 m/s. This analytical tunneling current model was then used to study how the germanium concentration in base to Si/Si1-xGex/Si heterojunction bipolar transistor influenced the tunneling current. It is obtained that tunneling current increased as the germanium concentration given in base decreased.

  6. Follow My Recommendations: A Personalized Privacy Assistant for Mobile App Permissions

    DEFF Research Database (Denmark)

    Andersen, Mads Schaarup; Liu, Bin; Schaub, Florian

    2016-01-01

    Modern smartphone platforms have millions of apps, many of which request permissions to access private data and resources, like user accounts or location. While these smartphone platforms provide varying degrees of control over these permissions, the sheer number of decisions that users are expec...

  7. Releasable activity and maximum permissible leakage rate within a transport cask of Tehran Research Reactor fuel samples

    Directory of Open Access Journals (Sweden)

    Rezaeian Mahdi

    2015-01-01

    Full Text Available Containment of a transport cask during both normal and accident conditions is important to the health and safety of the public and of the operators. Based on IAEA regulations, releasable activity and maximum permissible volumetric leakage rate within the cask containing fuel samples of Tehran Research Reactor enclosed in an irradiated capsule are calculated. The contributions to the total activity from the four sources of gas, volatile, fines, and corrosion products are treated separately. These calculations are necessary to identify an appropriate leak test that must be performed on the cask and the results can be utilized as the source term for dose evaluation in the safety assessment of the cask.

  8. An Ethics of Permission: A Response to the California End of Life Option Act.

    Science.gov (United States)

    Nelson, Craig

    2016-01-01

    An ethics of permission can be helpful in framing a response to the ethical differences surrounding the California End of Life Option Act. Law does not define morality, and reaching a moral understanding demands thorough reflection. An ethics of permission examines the ethical demands of a permissive law for both clinician and patient. Serving the good of the patient, respecting professional conscience, and following the law are three ethical elements. Although developing an ethics of permission includes these three elements, these elements do not exhaust all the moral implications involved. An ethics of permission also includes the importance of exercising professional tolerance in the honoring of clinicians who choose to participate or refuse to participate. In addition, an ethics of permission also provides insight in implementing just and fair behavior among medical professionals.

  9. Comparison of calculated and measured soil-gas radon concentration and radon exhalation rate

    International Nuclear Information System (INIS)

    Neznal, Martin; Neznal, Matej; Jiranek, Martin

    2000-01-01

    The computer model RADON2D for WINDOWS, which makes it possible to estimate the radon exhalation rate from the ground surface and the distribution of soil-gas radon concentration, was tested using a large set of experimental data coming from four reference areas located in regions with different geological structure. A good agreement between calculated and experimental data was observed. In the majority of cases, a correct description of the real situation was obtained using non-modified experimental input data. (author)

  10. Permissive underfeeding versus target enteral feeding in adult critically ill patients (PermiT Trial: a study protocol of a multicenter randomized controlled trial

    Directory of Open Access Journals (Sweden)

    Arabi Yaseen M

    2012-10-01

    Full Text Available Abstract Background Nutritional support is an essential part of the management of critically ill patients. However, optimal caloric intake has not been systematically evaluated. We aim to compare two strategies of enteral feeding: permissive underfeeding versus target feeding. Method/Design This is an international multi-center randomized controlled trial in critically ill medical- surgical adult patients. Using a centralized allocation, 862 patients will be randomized to permissive underfeeding or target feeding. Patients in the permissive group receive 50% (acceptable range is 40% to 60% of the calculated caloric requirement, while those in the targeted group receive 100% (acceptable range 70% to 100% of the calculated caloric requirement. The primary outcome is 90-day all-cause mortality. Secondary outcomes include ICU and hospital mortality, 28-day, and 180-day mortality as well as health care-associated infections, organ failure, and length of stay in the ICU and hospital. The trial has 80% power to detect an 8% absolute reduction in 90-day mortality assuming a baseline risk of death of 25% at an alpha level of 0.05. Discussion Patient recruitment started in November 2009 and is currently active in five centers. The Data Monitoring Committee advised continuation of the trial after the first interim analysis. The study is expected to finish by November 2013. Trial registration Current Controlled Trials ISRCTN68144998

  11. [Behavior of Orf virus in permissive and nonpermissive systems].

    Science.gov (United States)

    Büttner, M; Czerny, C P; Schumm, M

    1995-04-01

    Dogs were immunized i.m. with attenuated poxvirus vaccines (vaccinia virus, Orf-virus) and a bovine herpesvirus-1 (BHV-1) vaccine. After intradermal (i.d.) application of the vaccine viruses a specific delayed type hypersensitivity (DTH) reaction of the skin occurred only with vaccinia virus. The i.d. application of Orf-virus caused a short-term, non-specific inflammatory reaction of the skin, even in dogs not immunized with Orf-virus. Out of 30 sera from Orf-virus immunized beagles (n = 4) only eight were found reactive to Orf-virus in a competition ELISA. Three sera from dogs not Orf-virus immunized but skin-tested with the virus contained low antibody titers. Using indirect immunofluorescence (IIF) in flow cytometry, the existence of Orf-virus antigens was examined on the surface and in the cytoplasm of permissive (BFK and Vero)- and questionable permissive MDCK cells. The canine kidney MDCK cell line was found to be non-permissive for Orf-virus replication; the occurrence of an Orf-(ecthyma contagiosum) like disease in dogs is unlikely.

  12. Estimation of minimum detectable concentration of chlorine in the blast furnace slag cement concrete

    Energy Technology Data Exchange (ETDEWEB)

    Naqvi, A.A., E-mail: aanaqvi@kfupm.edu.s [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Maslehuddin, M. [Center for Engineering Research, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Garwan, M.A.; Nagadi, M.M. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Al-Amoudi, O.S.B. [Department of Civil Engineering, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Khateeb-ur-Rehman,; Raashid, M. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

    2011-01-01

    The Prompt Gamma Neutron Activation Analysis technique was used to measure the concentration of chloride in the blast furnace slag (BFS) cement concrete to assess the possibility of reinforcement corrosion. The experimental setup was optimized using Monte Carlo calculations. The BFS concrete specimens containing 0.8-3.5 wt.% chloride were prepared and the concentration of chlorine was evaluated by determining the yield of 6.11, 6.62, 7.41, 7.79 and 8.58 MeV gamma-rays. The Minimum Detectable Concentration (MDC) of chlorine in the BFS cement concrete was estimated. The best value of MDC limit of chlorine in the BFS cement concrete was found to be 0.034 {+-} 0.011 and 0.038 {+-} 0.012 wt.% for 6.11 and 6.62 MeV prompt gamma-rays. Within the statistical uncertainty the lower bound of the measured MDC of chlorine in the BFS cement concrete meets the maximum permissible limit of 0.03 wt.% of chloride set by the American Concrete Institute.

  13. Religiosity and Premarital Sexual Permissiveness: A Response to the Reiss-Heltsley and Broderick Debate

    Science.gov (United States)

    Ruppel, Howard J., Jr.

    1970-01-01

    When religiosity among college students was measured by Faulkner and DeJong's 5-D Scale of Religiosity" and the Reiss scale was used to measure permissiveness, the expected stronger relationship between religiosity and permissiveness in groups with traditions of low sexual permissiveness than in groups with traditions of high sexual…

  14. Gender Differences In Premarital Sexual Permissiveness Among ...

    African Journals Online (AJOL)

    This paper examined the concept of premariatal sexual permissiveness among selected University undergraduates in a state owned university in Nigeria, believing that the policy of non-residential status of the University will facilitate premarital sexual activity among the students. Using a total of 400 purposively selected ...

  15. Urine Creatinine Concentrations in Drug Monitoring Participants and Hospitalized Patients.

    Science.gov (United States)

    Love, Sara A; Seegmiller, Jesse C; Kloss, Julie; Apple, Fred S

    2016-10-01

    Urine drug testing is commonly performed in both clinical and forensic arenas for screening, monitoring and compliance purposes. We sought to determine if urine creatinine concentrations in monitoring program participants were significantly different from hospital in-patients and out-patients undergoing urine drug testing. We retrospectively reviewed urine creatinine submitted in June through December 2015 for all specimens undergoing urine drug testing. The 20,479 creatinine results were categorized as hospitalized patients (H) and monitoring/compliance groups for pain management (P), legal (L) or recovery (R). Median creatinine concentrations (interquartile range, mg/dL) were significantly different (P creatinine concentrations were significantly lower in the R vs. L group (Pcreatinine concentration and may indicate participants' attempts to tamper with their drug test results through dilution means. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  16. Axiomatizations of Banzhaf Permisson Values for Games with a Hierarchical Permission Structure.

    NARCIS (Netherlands)

    van den Brink, J.R.

    2010-01-01

    In games with a permission structure it is assumed that players in a cooperative transferable utility game are hierarchically ordered in the sense that there are players that need permission from other players before they are allowed to cooperate. We provide axiomatic characterizations of Banzhaf

  17. Permissivity of the NCI-60 cancer cell lines to oncolytic Vaccinia Virus GLV-1h68

    International Nuclear Information System (INIS)

    Ascierto, Maria Libera; Bedognetti, Davide; Uccellini, Lorenzo; Rossano, Fabio; Ascierto, Paolo A; Stroncek, David F; Restifo, Nicholas P; Wang, Ena; Szalay, Aladar A; Marincola, Francesco M; Worschech, Andrea; Yu, Zhiya; Adams, Sharon; Reinboth, Jennifer; Chen, Nanhai G; Pos, Zoltan; Roychoudhuri, Rahul; Di Pasquale, Giovanni

    2011-01-01

    Oncolytic viral therapy represents an alternative therapeutic strategy for the treatment of cancer. We previously described GLV-1h68, a modified Vaccinia Virus with exclusive tropism for tumor cells, and we observed a cell line-specific relationship between the ability of GLV-1h68 to replicate in vitro and its ability to colonize and eliminate tumor in vivo. In the current study we surveyed the in vitro permissivity to GLV-1h68 replication of the NCI-60 panel of cell lines. Selected cell lines were also tested for permissivity to another Vaccinia Virus and a vesicular stomatitis virus (VSV) strain. In order to identify correlates of permissity to viral infection, we measured transcriptional profiles of the cell lines prior infection. We observed highly heterogeneous permissivity to VACV infection amongst the cell lines. The heterogeneity of permissivity was independent of tissue with the exception of B cell derivation. Cell lines were also tested for permissivity to another Vaccinia Virus and a vesicular stomatitis virus (VSV) strain and a significant correlation was found suggesting a common permissive phenotype. While no clear transcriptional pattern could be identified as predictor of permissivity to infection, some associations were observed suggesting multifactorial basis permissivity to viral infection. Our findings have implications for the design of oncolytic therapies for cancer and offer insights into the nature of permissivity of tumor cells to viral infection

  18. Breakout Session: Fight for Your Right to Copy: How One Library Acquired the Copyright Permissions Service and Reduced Students’ Costs. Presented by Emily Riha, Copyright Permissions Coordinator, University of Minnesota.

    Directory of Open Access Journals (Sweden)

    Connie Strittmatter

    2018-02-01

    Full Text Available Emily Riha, Copyright Permissions Coordinator at the University of Minnesota, presented at the 2017 Kraemer Copyright Conference her experience when the process of securing copyright permissions moved from Printing Services to the University Libraries.

  19. 26 CFR 1.422-5 - Permissible provisions.

    Science.gov (United States)

    2010-04-01

    ... of the incentive stock option are subject to a substantial risk of forfeiture and not transferable...) INCOME TAXES Certain Stock Options § 1.422-5 Permissible provisions. (a) General rule. An option that otherwise qualifies as an incentive stock option does not fail to be an incentive stock option merely...

  20. Model equations for Calculating Rn-gas Concentrations in Air of Uranium Exploratory Tunnels, Allouga, West-Central Sinai , Egypt

    International Nuclear Information System (INIS)

    Abdel-Monem, A.A.; Soliman, S.F.H.; Abd El-Kader, F.H.; El-Naggar, A.M.; Eissa, H.M.; Abd El-Hafez, A.A.

    2001-01-01

    Gabal Allouga area is located some 40 km due east from Abu Zenima town on the east coast of the Gulf of Suez, West-Central Sinai, Egypt. A network of exploratory tunnels totaling 670m in length and approximately 2x2 m in cross section, were excavated within a paleosol clayey bed. They host (Fe, Mn)-, Cu-, and U-mineralizations. Portions of the tunnels are naturally ventilated and others portions are non-ventilated and show ground water seepage through fractures. Model equations were developed for calculating the Rn-gas concentrations in the air of the tunnels under dry conditions where Rn-gas transport is mainly by air flow through porous media as well as for wet conditions where Rn-gas transport is mainly by ground water flow into the tunnels. Under dry conditions the model calculated Rn-gas concentrations(15.2-60.6 PCi/1) are consistent with measured values by active techniques (3.26-22.85 pCi/1) and by SSNTD techniques (19-69.1 pCi/1) when the Rn-emanation coefficient (alpha= 0.05-0.2), the emanating rock thickness (X=10 cm) and U-concentration averages 30 ppm. Under wet and non-ventilated conditions the model calculated Rn-gas concentrations (159-1248 pCi/1) are consistent with the measured values by active techniques (231-1348 pCi/1) and by SSNTD techniques (144-999pCi/1), when the Rn-emanation coefficient (alpha=0.1-0.25), the ground water flow (F=0.04-0.10 ml/s -1 cm -2 ) and U-concertrations (100-250ppm)

  1. 17 CFR 230.433 - Conditions to permissible post-filing free writing prospectuses.

    Science.gov (United States)

    2010-04-01

    ... writing prospectus used at the same time as a communication in a business combination transaction subject... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Conditions to permissible post... Prospectuses § 230.433 Conditions to permissible post-filing free writing prospectuses. (a) Scope of section...

  2. Maternal risk factors in fetal alcohol syndrome: provocative and permissive influences.

    Science.gov (United States)

    Abel, E L; Hannigan, J H

    1995-01-01

    We present an hypothesis integrating epidemiological, clinical case, and basic biomedical research to explain why only relatively few women who drink alcohol during pregnancy give birth to children with alcohol-related birth defects (ARBDs), in particular, Fetal Alcohol Syndrome (FAS). We argue that specific sociobehavioral risk factors, e.g., low socioeconomic status, are permissive for FAS in that they provide the context for increased vulnerability. We illustrate how these permissive factors are related to biological factors, e.g., decreased antioxidant status, which in conjunction with alcohol, provoke FAS/ARBDs in vulnerable fetuses. We propose an integrative heuristic model hypothesizing that these permissive and provocative factors increase the likelihood of FAS/ARBDs because they potentiate two related mechanisms of alcohol-induced teratogenesis, specifically, maternal/fetal hypoxia and free radical formation.

  3. A Dynamic Operation Permission Technique Based on an MFM Model and Numerical Simulation

    International Nuclear Information System (INIS)

    Akio, Gofuku; Masahiro, Yonemura

    2011-01-01

    It is important to support operator activities to an abnormal plant situation where many counter actions are taken in relatively short time. The authors proposed a technique called dynamic operation permission to decrease human errors without eliminating creative idea of operators to cope with an abnormal plant situation by checking if the counter action taken is consistent with emergency operation procedure. If the counter action is inconsistent, a dynamic operation permission system warns it to operators. It also explains how and why the counter action is inconsistent and what influence will appear on the future plant behavior by a qualitative influence inference technique based on a model by the Mf (Multilevel Flow Modeling). However, the previous dynamic operation permission is not able to explain quantitative effects on plant future behavior. Moreover, many possible influence paths are derived because a qualitative reasoning does not give a solution when positive and negative influences are propagated to the same node. This study extends the dynamic operation permission by combining the qualitative reasoning and the numerical simulation technique. The qualitative reasoning based on an Mf model of plant derives all possible influence propagation paths. Then, a numerical simulation gives a prediction of plant future behavior in the case of taking a counter action. The influence propagation that does not coincide with the simulation results is excluded from possible influence paths. The extended technique is implemented in a dynamic operation permission system for an oil refinery plant. An MFM model and a static numerical simulator are developed. The results of dynamic operation permission for some abnormal plant situations show the improvement of the accuracy of dynamic operation permission and the quality of explanation for the effects of the counter action taken

  4. Procedures for permission under atomic energy laws in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Kuhnt, D.

    1980-01-01

    The selection of proper locations by the enterprisers responsible for projects is usually accompanied in recent years by the active location policy of the state. The application for the permission of locations and projects shall be filed to one or more ministries of the province where the facilities are to be installed. The papers describing the projects, especially safety reports and summaries shall be attached to the applications. The applications shall be published on a bulletin of the government office or daily newspapers, and every person has access to the applications, the safety reports and the summaries for two months. When objections are lodged within the period, closed hearings are held to examine the protests with attendance of the objector, the enterpriser of the project and the government office which has joined the decision. Following the phase of public participation and after the confirmation of facts highly important to the decision, fact examination is carried out with cooperation of specialists by the government office authorized for permission. As a special feature of the procedures under Atomgesetz, the government office is not necessarily obliged to give permission considering the safety policy, even when the pre-requisites of permission are all fulfilled. In other respects, permission may be offered for each partial installation of the facilities and various stages of operation by particular administrative measures (partial permission). The experiences of past 20 years indicate the virtual defects of the laws applied, and the amendment is urgently required. (Okada, K.)

  5. Immortalized sheep microglial cells are permissive to a diverse range of ruminant viruses.

    Science.gov (United States)

    Stanton, James B; Swanson, Beryl; Orozco, Edith; Muñoz-Gutiérrez, Juan F; Evermann, James F; Ridpath, Julia F

    2017-12-01

    Ruminants, including sheep and goats (small ruminants), are key agricultural animals in many parts of the world. Infectious diseases, including many viral diseases, are significant problems to efficient production of ruminants. Unfortunately, reagents tailored to viruses of ruminants, and especially small ruminants, are lacking compared to other animals more typically used for biomedical research. The purpose of this study was to determine the permissibility of a stably immortalized, sheep microglial cell line to viruses that are reported to infect ruminants: bovine viral diarrhea virus (BVDV), bovine herpesvirus 1 (BoHV-1), small ruminant lentiviruses (SRLV), and bovine respiratory syncytial virus (BRSV). Sublines A and H of previously isolated, immortalized, and characterized (CD14-positive) ovine microglial cells were used. Bovine turbinate cells and goat synovial membrane cells were used for comparison. Cytopathic changes were used to confirm infection of individual wells, which were then counted and used to calculate the 50% tissue culture infectious dose. Uninoculated cells served as negative controls and confirmed that the cells were not previously infected with these viruses using polymerase chain reaction (PCR). Inoculation of the two microglial cell sublines with laboratory and field isolates of BVDV, BoHV-1, and BRSV resulted in viral infection in a manner similar to bovine turbinate cells. Immortalized microglia cells are also permissive to SRLV, similar to goat synovial membrane cells. These immortalized sheep microglial cells provide a new tool for the study of ruminant viruses in ruminant microglial cell line.

  6. Parental permissiveness, control, and affect and drug use among adolescents.

    Science.gov (United States)

    Becoña, Elisardo; Martínez, Úrsula; Calafat, Amador; Fernández-Hermida, José Ramón; Juan, Montse; Sumnall, Harry; Mendes, Fernando; Gabrhelík, Roman

    2013-01-01

    Parents play an important role in determining the risk of children's drug use. The aim of this study was to analyse how certain family-related variables (permissiveness toward drug use, and parental control and affect) were linked to the use of alcohol, tobacco and cannabis, based on young people's self-report of such variables. The sample was composed of 1,428 school children (51.8% males) aged between 11 and 19 from Mallorca (Spain). We found that the young people who perceived their parents as permissive and those who perceived less maternal control and higher levels of both paternal and maternal affect were more likely to use alcohol, tobacco and cannabis. Sex differences were found within this pattern. Variables of maternal affect and control were not influential among males, whereas the general pattern was maintained among females. This study highlights the importance of perceived permissiveness and the need of considering parent's and children's gender when providing control and affect, as fathers will influence male children whereas mothers will influence female children.

  7. Permissive parenting and mental health in college students: Mediating effects of academic entitlement.

    Science.gov (United States)

    Barton, Alison L; Hirsch, Jameson K

    2016-01-01

    Student mental health may suffer due to unreasonable expectations associated with academic entitlement; permissive parenting may be one source of these expectations. The authors examined the role of academic entitlement as a mediator of the relationship between permissive parenting and psychological functioning. Participants were 524 undergraduate students at a single institution (52% female; age range = 18-22). Data collection was completed in May 2011. Cross-sectional design. Participants completed online self-report measures of parenting styles, academic entitlement, stress, depressive symptoms, and well-being. Permissive parenting was associated with greater academic entitlement and, in turn, to more perceived stress and poorer mental health. Mother/father differences were found in some cases. Academic entitlement may partially explain why permissive parenting is detrimentally related to mental health for college students. Implications for academic affairs and counseling include helping students develop an appreciation of the role of self-regulation in college success.

  8. Permissive Parenting and Mental Health in College Students: Mediating Effects of Academic Entitlement

    Science.gov (United States)

    Barton, Alison L.; Hirsch, Jameson K.

    2016-01-01

    Objective: Student mental health may suffer due to unreasonable expectations associated with academic entitlement; permissive parenting may be one source of these expectations. The authors examined the role of academic entitlement as a mediator of the relationship between permissive parenting and psychological functioning. Participants:…

  9. 50 CFR 216.252 - Permissible methods of taking.

    Science.gov (United States)

    2010-10-01

    ... ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking Marine Mammals Incidental to Conducting Precision Strike Weapon Missions in the Gulf of Mexico § 216.252 Permissible methods of taking. (a) Under Letters of Authorization issued pursuant to...

  10. Calculation of Radioactivity Concentration on Cover Depth of Contaminated Zone for Self-Disposal

    Energy Technology Data Exchange (ETDEWEB)

    Koo, Daeseo; Sung, Hyun-Hee; Kim, Gye-Nam; Kim, Seung-Soo; Kim, Ilgook; Han, Gyu Seong; Choi, Jong-Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    We have a lot of uranium contaminated soil and concrete wastes owing to dismantlement of uranium conversion facility. There are several radioactive material disposal methods such as regulation exemption, decontamination and long term storage. It is necessary for us to perform permanent disposal of these wastes. To acquire radiation dose under self-disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinectic-electrodialytic. In this study, we evaluated radiation dose on the cover depth of contaminated zone from the wastes under radiation dose limit using RESRAD Version 6.5. At first, the calculation of the radiation dose on the wastes of contaminated zone are carried out. The second, the cover depth of contaminated zone are analyzed. The application to self-disposal of contaminated zone are also analyzed. To acquire radiation dose under self-disposal from uranium contaminated soil and concrete wastes, we decontaminated some uranium contaminated soil and concrete wastes using electrokinectic-electrodialytic. To perform self-disposal of the quantity (30,000kg) of contaminated zone, the calculating conditions for radiation dose on the cover depth of contaminated zone are as follows. The area of contaminated zone is 10m{sup 2}. The thickness of contaminated zone is 2 m. The cover depth of contaminated zone are analyzed. The application to self-disposal of contaminated zone are also analyzed. Therefore, as the cover depth increases, the uranium concentration has an increasing trend. It realize that the cover depth of contaminated zone is adequate < 2m at the quantity(30,000kg) of contaminated zone. As the cover depth increases, the uranium concentration has a decreasing trend. As the cover depth increases, the radiation dose(residents) has also a decreasing trend.

  11. 50 CFR 216.213 - Permissible methods of taking.

    Science.gov (United States)

    2010-10-01

    ... ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking of Marine Mammals Incidental to Explosive Severance Activities Conducted During Offshore Structure Removal Operations on the Outer Continental Shelf in the U.S. Gulf of Mexico § 216.213 Permissible...

  12. 36 CFR 223.12 - Permission to cut, damage, or destroy trees without advertisement.

    Science.gov (United States)

    2010-07-01

    ... destroy trees without advertisement. 223.12 Section 223.12 Parks, Forests, and Public Property FOREST... § 223.12 Permission to cut, damage, or destroy trees without advertisement. Permission may be granted to cut, damage, or destroy trees, portions of trees, or other forest products on National Forest System...

  13. 47 CFR 74.790 - Permissible service of digital TV translator and LPTV stations.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Permissible service of digital TV translator... DISTRIBUTIONAL SERVICES Low Power TV, TV Translator, and TV Booster Stations § 74.790 Permissible service of digital TV translator and LPTV stations. (a) Digital TV translator stations provide a means whereby the...

  14. Legitimate Permissions And Specifity Of Their Enforceability In Modern Russia

    Directory of Open Access Journals (Sweden)

    Vitaly Subochev

    2014-01-01

    Full Text Available Northern Caucasus Institute of Advanced Training (branch of Krasnodar University of Ministry of Internal Affairs of Russia, 123, Malbahova Street, Nalshik, 360016, Russia. Abstract: The article investigates the basic legal permissions in Russian law - legal rights, freedoms and legitimate interests. Potential of these means of legal regulation is examined as well as their common features and essential differences. Authors argue that the effectiveness of the mechanism of legal regulation largely depends on the proper use of legal permissions. Particular attention is paid to such kind of legal mean as a legitimate interest. The article draws attention to the fact that if a legal right or freedom are such kind of permissions which are guaranteed by the law in order to sustain certain demands of subjects of law, the legitimate interest is qualitatively different mean of regulation. The authors suggest considering a legitimate interest as reflected in the objective law legal possibility of subjects of law to enjoy certain social benefits and to seek protection from the state authorities in order to meet their interests which are not contradictory to provisions of law. Qualitative difference between legitimate interest and legal right and freedom is that the legitimate interest is an opportunity, guaranteed to a lesser extent than the permitted behavior within a legal right or freedom. Legitimate interest is a mere permission, admitted by the state and to some extent supported by it. But legal right and freedom - are those means of regulation, which are directly approved and sanctioned by the state which presuppose duty of a person to a particular behavior. The author's vision of the specifity of legal enforcement of legitimate admissions is presented.

  15. LEGITIMATE PERMISSIONS AND SPECIFITY OF THEIR ENFORCEABILITY IN MODERN RUSSIA

    Directory of Open Access Journals (Sweden)

    Vitaly Subochev

    2014-01-01

    Full Text Available Northern Caucasus Institute of Advanced Training (branch of Krasnodar University of Ministry of Internal Affairs of Russia, 123, Malbahova Street, Nalshik, 360016, Russia. Abstract: The article investigates the basic legal permissions in Russian law - legal rights, freedoms and legitimate interests. Potential of these means of legal regulation is examined as well as their common features and essential differences. Authors argue that the effectiveness of the mechanism of legal regulation largely depends on the proper use of legal permissions. Particular attention is paid to such kind of legal mean as a legitimate interest. The article draws attention to the fact that if a legal right or freedom are such kind of permissions which are guaranteed by the law in order to sustain certain demands of subjects of law, the legitimate interest is qualitatively different mean of regulation. The authors suggest considering a legitimate interest as reflected in the objective law legal possibility of subjects of law to enjoy certain social benefits and to seek protection from the state authorities in order to meet their interests which are not contradictory to provisions of law. Qualitative difference between legitimate interest and legal right and freedom is that the legitimate interest is an opportunity, guaranteed to a lesser extent than the permitted behavior within a legal right or freedom. Legitimate interest is a mere permission, admitted by the state and to some extent supported by it. But legal right and freedom - are those means of regulation, which are directly approved and sanctioned by the state which presuppose duty of a person to a particular behavior. The author's vision of the specifity of legal enforcement of legitimate admissions is presented.

  16. Variable Potassium Concentrations: Which Is Right and Which Is Wrong?

    Science.gov (United States)

    Theparee, Talent; Benirschke, Robert C; Lee, Hong-Kee

    2017-05-01

    Reverse pseudohyperkalemia is a term used to describe in vitro, falsely elevated potassium concentrations in plasma specimens that occur in association with extreme leukocytosis and are commonly associated with hematologic malignant neoplasms. Tumor lysis syndrome is an in vivo lysis of tumor cells that leads to elevated levels of potassium, uric acid, phosphate, and lactate dehydrogenase, as well as decreased calcium concentrations. Herein, we report a case of a 66-year-old Caucasian man with stage IV mantle-cell lymphoma who has elevated levels of potassium, uric acid, and phosphorus, as well as a white blood cell (WBC) count greater than 100,000 cells per mm3. The patient initially was diagnosed as having tumor lysis syndrome. His subsequent potassium concentrations in whole blood remained elevated even after hemodialysis; however, his serum potassium concentrations were decreased. The patient then was diagnosed accurately as having reverse pseudohyperkalemia, and accurate potassium measurements were obtained via serum specimens. © American Society for Clinical Pathology, 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  17. Calculation of the thermal utilisation factor in a cell made up of a given number of concentric media

    International Nuclear Information System (INIS)

    Amouyal, A.; Benoist, P.; Guionnet, Ch.

    1961-01-01

    The method of calculating the thermal utilisation factor, described in a previous report, is extended to the case of a cylindrical cell containing a given number of concentric media, certain of which may be empty. A collision by collision method is used in all but the peripheral medium, which may be treated by a theory of controlled diffusion. A programme for the IBM 650 calculator has been based on this method. Some numerical results are presented. An equivalent matrix formulation, due to C. Guionnet, is given as an appendix. (author) [fr

  18. A new model for deteriorating items with inflation under permissible delay in payments

    Directory of Open Access Journals (Sweden)

    R.P. Tripathi

    2014-05-01

    Full Text Available Inflation is an important factor influencing traditional economic order quality models. Marketing strategy depends on inflation due to public demand and availability of the materials. This paper presents an optimal inventory policy for deteriorating items using exponential demand rate under permissible delay in payments. Mathematical model has been derived under two cases: case I: cycle time is greater than or equal to permissible delay period, case II: cycle time is less than permissible delay period by considering holding cost as a function of time. Numerical examples and sensitivity analysis are given to reflect the numerical results. Mathematica software is used for finding optimal solutions.

  19. Development of hybrid core calculation system using 2-D full-core heterogeneous transport calculation and 3-D advanced nodal calculation

    International Nuclear Information System (INIS)

    Sugimura, Naoki; Mori, Masaaki; Hijiya, Masayuki; Ushio, Tadashi; Arakawa, Yasushi

    2004-01-01

    This paper presents the Hybrid Core Calculation System which is a very rigorous but a practical calculation system applicable to best estimate core design calculations taking advantage of the recent remarkable progress of computers. The basic idea of this system is to generate the correction factors for assembly homogenized cross sections, discontinuity factors, etc. by comparing the CASMO-4 and SIMULATE-3 2-D core calculation results under the consistent calculation condition and then apply them for SIMULATE-3 3-D calculation. The CASMO-4 2-D heterogeneous core calculation is performed for each depletion step with the core conditions previously determined by ordinary SIMULATE-3 core calculation to avoid time consuming iterative calculations searching for the critical boron concentrations while treating the thermal hydraulic feedback. The final SIMULATE-3 3-D calculation using the correction factors is performed with iterative calculations searching for the critical boron concentrations while treating the thermal hydraulic feedback. (author)

  20. DelPhiForce web server: electrostatic forces and energy calculations and visualization.

    Science.gov (United States)

    Li, Lin; Jia, Zhe; Peng, Yunhui; Chakravorty, Arghya; Sun, Lexuan; Alexov, Emil

    2017-11-15

    Electrostatic force is an essential component of the total force acting between atoms and macromolecules. Therefore, accurate calculations of electrostatic forces are crucial for revealing the mechanisms of many biological processes. We developed a DelPhiForce web server to calculate and visualize the electrostatic forces at molecular level. DelPhiForce web server enables modeling of electrostatic forces on individual atoms, residues, domains and molecules, and generates an output that can be visualized by VMD software. Here we demonstrate the usage of the server for various biological problems including protein-cofactor, domain-domain, protein-protein, protein-DNA and protein-RNA interactions. The DelPhiForce web server is available at: http://compbio.clemson.edu/delphi-force. delphi@clemson.edu. Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

  1. Calculations of radiation levels during reactor operations for safeguard inspections

    International Nuclear Information System (INIS)

    Sobhy, M.

    1996-01-01

    When an internal core spent fuel storage is used in the shield tank to accommodate a large number of spent fuel baskets, physical calculations are performed to determine the number of these spent fuel elements which can be accommodated and still maintain the gamma activity outside under the permissible limit. The corresponding reactor power level is determined. The radioactivity calculations are performed for this internal storage at different axial levels to avoid the criticality of the reactor core. Transport theory is used in calculations based on collision probability for multi group cell calculations. Diffusion theory is used in three dimensions in the core calculations. The nuclear fuel history is traced and radioactive decay is calculated, since reactor fission products are very sensitive to power level. The radioactivity is calculated with a developed formula based on fuel basket loading integrity. (author)

  2. Ozone in the Upper Silesia region -- concentration and effects on plants

    Science.gov (United States)

    Stefan Godzik

    1998-01-01

    In the Beskidy Mountains at Brenna, Poland, and several other locations in the Katowice administrative district, plants were used as bioindicators to determine ozone concentration measurements in 1994 and 1995. Results showed that ozone is the only gaseous air pollutant significantly exceeding the permissible concentrations and causing foliar injury to both test and...

  3. Influence of Permissive Parenting on Youth Farm Risk Behaviors.

    Science.gov (United States)

    Jinnah, Hamida A; Stoneman, Zolinda

    2016-01-01

    Farm youth continue to experience high rates of injuries and premature deaths as a result of agricultural activities. Increased parental permissiveness is positively associated with many different types of high-risk behaviors in youth. This study explored whether permissive parenting (fathering and mothering) predicts youth unsafe behaviors on the farm. Data were analyzed for 67 youth and their parents. Families were recruited from a statewide farm publication, through youth organizations (i.e., FFA [Future Farmers of America]), local newspapers, farmer referrals, and through the Cooperative Extension Network. Hierarchical multiple regression was completed. Results revealed that fathers and mothers who practiced lax-inconsistent disciplining were more likely to have youth who indulged in unsafe farm behaviors. Key hypotheses confirmed that permissive parenting (lax-inconsistent disciplining) by parents continued to predict youth unsafe farm behaviors, even after youth age, youth gender, youth personality factor of risk-taking, and father's unsafe behaviors (a measure associated with modeling) were all taken into account. A key implication is that parents may play an important role in influencing youth farm safety behaviors. Parents (especially fathers) need to devote time to discuss farm safety with their youth. Farm safety interventions need to involve parents as well as address and respect the culture and values of families. Interventions need to focus not only on safe farm practices, but also promote positive parenting practices, including increased parent-youth communication about safety, consistent disciplining strategies, and increased monitoring and modeling of safe farm behaviors by parents.

  4. Activity concentration and radiological impact assessment of 226Ra, 228Ra and 40K in drinking waters from (OML) 30, 58 and 61 oil fields and host communities in Niger Delta region of Nigeria

    International Nuclear Information System (INIS)

    Agbalagba, E.O.; Avwiri, G.O.; Ononugbo, C.P.

    2013-01-01

    This paper presents the concentrations of naturally occurring radionuclides ( 226 Ra, 228 Ra and 40 K) measured in hand dug wells, boreholes and river waters collected from three oil mineral leases (OML) 30, 58 and 61 oil and gas fields onshore of the Niger delta, using gamma spectroscopy. Fifty-four water samples from the three sources of drinking water supply were collected within the oil fields and host communities and three water samples from a control site. The results showed average activity concentrations of 226 Ra, 228 Ra and 40 K as 8.9 ± 1.0, 8.1 ± 0.9 and 39.8 ± 3.3 respectively for hand dug wells, 4.4 ± 0.8, 4.6 ± 0.5 and 28.5 ± 3.0 for borehole water and 8.2 ± 1.0, 6.7 ± 0.7 and 32.1 ± 3.5 for river water respectively. These 226 Ra, 228 Ra and 40 K average are well above the WHO permissible levels of 1.0, 0.1 and 10 BqL −1 respectively and also above the control values. Although the hazard indices calculated are still within their tolerable levels, the estimated committed effective dose due to intake of the sampled water for all the four age groups considered are far above the ICPR 0.1 mSvyr −1 maximum permissible limit. The result indicates some level of water pollution in the studied area. - Highlights: ► The concentration of natural radioactive series nuclides varies widely within oil fields and from one oil field to another in the OML30. ► The radionuclide activity concentrations in most water samples are higher than world average values. ► Calculated hazard indices and committed effective dose to assess the potential radiological health risk in samples are well above their permissible limit. ► The sources of water in these oil fields have been polluted and may cause some health hazard to the public users.

  5. Model for Calculating the Maximum Permissible Tax Burden in Amur Region in the Context of the Implementation of Largest Investment Projects

    Directory of Open Access Journals (Sweden)

    Viktor Vladimirovich Ivanov

    2018-03-01

    Full Text Available According to the Government of the Amur region, tax collection from the implementation of investment projects was tightly controlled from 2016, because of the region’s high debt load. This situation requires assessing the acceptability of the level of regional tax burden for business entities. The purpose of this paper is to develop a model for assessing the level of regional tax burden, taking into account the implementation of the largest investment projects in the territory. The main hypothesis of this paper consists, firstly, in the existence of tax burden, which is acceptable for regional economic entities. Secondly, this level of tax burden ensures the growth of fiscal revenues for the budget. We proposed to assess the level of tax burden on the basis of a three-factor linear heterogeneous production function, taking into account certain economic indicators of the largest investment project — “Construction of the Vostochny Сosmodrome”. The concept of the Laffer curve serves as a research methodology. According to our calculations, since 2011, the tax burden in the Amur region has a clear tendency to increase. At the same time, from 2007 to the present time, the tax burden exceeds its maximum permissible value and constrains economic growth in the region. If this trend continues, by 2018 tax revenues from the territory of the region will be on the verge of reduction. The obtained results show that the tax burden in the Amur region in 2017 is 16.81 %. To stimulate the activities of economic entities in the region, and as a consequence, to increase the GRP of the region, it is necessary to reduce the level of taxation by 4.77 percentage points (to 12.04 %, Thus, the current economic situation requires to change the course of regional taxation policy to a more liberal attitude towards taxpayers. Otherwise, soon the budget of the Amur region may fail to receive a part of revenues, as the region’s economic entities will not be able to

  6. The effect of boron concentration on the structure and elastic properties of Ru-Ir alloys: first-principles calculations

    Science.gov (United States)

    Li, Xiaolong; Zhou, Zhaobo; Hu, Riming; Zhou, Xiaolong; Yu, Jie; Liu, Manmen

    2018-04-01

    The Phase stability, electronic structure, elastic properties and hardness of Ru-Ir alloys with different B concentration were investigated by first principles calculations. The calculated formation enthaplies and cohesive energies show that these compounds are all thermodynamically stable. Information on electronic structure indicates that they possess metallic characteristic and Ru-Ir-B alloys were composed of the Ru-B and Ir-B covalent bond. The elastic properties were calculated, which included bulk modulus, shear modulus, Young’s modulus, Poisson’s ratio and hardness. The calculated results reveal that the plastic of Ru-Ir-B alloys increase with the increase of the content of B atoms, but the hardness of Ru-Ir-B alloys have no substantial progress with the increase of the content of B atoms. However, it is interesting that the hardness of the Ru-Ir-B compound was improved obviously as the B content was higher than 18 atoms because of a phase structure transition.

  7. 20 CFR 416.1321 - Suspension for not giving us permission to contact financial institutions.

    Science.gov (United States)

    2010-04-01

    ... contact financial institutions. 416.1321 Section 416.1321 Employees' Benefits SOCIAL SECURITY....1321 Suspension for not giving us permission to contact financial institutions. (a) If you don't give us permission to contact any financial institution and request any financial records about you when...

  8. Variation of atmospheric tritium concentration in three chemical forms at Toki, Japan: 2004-12.

    Science.gov (United States)

    Tanaka, M; Uda, T

    2015-11-01

    Atmospheric tritium concentrations of HTO, HT and CH3T have been measured at Toki, Japan, for the environmental impact assessment of tritium for a fusion test facility. According to the data from 2004 to 2012, the concentrations of HT and HTO in water vapour tend to increase in spring. The seasonal variation in HT concentration at Toki was compared with the H2 concentration between 1990 and 2005 at Tae-ahn Peninsula, Republic of Korea, which is at approximately the same latitude as Toki. The monthly average of HT-specific activity varied from 1.24 × 10(5) to 1.76 × 10(5) TU. The peak of the monthly average H2 concentration did not match that of HT. This indicates that the mechanism of the production or the source of HT might be different from the production mechanism of H2. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  9. On permission of waste-burying business in Tokai Research Establishment, Japan Atomic Energy Research Institute (Answer)

    International Nuclear Information System (INIS)

    1995-01-01

    As to this case written in the title which was inquired on July 19, 1994, from the prime minister, and changed partly on November 21, 1994, the Nuclear Safety Commission answered to the prime minister as follows after the prudent deliberation. As for the application of the criteria for permission, the technical capability is adequate, and the results of the examination of safety by the expert committee for examining nuclear fuel safety is adequate. It was judged that the safety after the permission of this waste-burying business can be secured. The expert committee reported on the policy of the investigation and deliberation, and the contents of the investigation and deliberation, such as the basic location conditions, namely, site, weather, ground, hydraulics, earthquakes and social environment, the radioactive wastes to be buried, the method of determining radioactivity concentration, the expected time of changing the measures to be taken for security, the safety design for the waste-burying facility related to radiation control, environment safety, earthquakes, fires and explosion, the loss of electric power and the standards and criteria to be conformed, and the assessment of dose equivalent in normal state, after finishing the period of control and safety evaluation, and the course of the investigation and deliberation. (K.I.)

  10. Early alcohol use with parental permission: Psychosocial characteristics and drinking in late adolescence.

    Science.gov (United States)

    Colder, Craig R; Shyhalla, Kathleen; Frndak, Seth E

    2018-01-01

    The earliest experiences with alcohol for many children occur in the family context with parental supervision. The current study examined individual and sociocultural characteristics associated with early (prior to age 13years) sipping and tasting alcohol with parental permission in two longitudinal community samples. Early sipping/tasting was also tested as a predictor of frequency and quantity of alcohol use, and alcohol-related problems seven years later in late adolescence. Early sipping/tasting with parental permission was associated with a sociocultural context supportive of alcohol use (e.g., parental alcohol use, permissive rules about alcohol use in the home, parental attitudes about underage drinking, perceived peer norms), adolescent sensation seeking and disinhibition (e.g., surgency, externalizing behavior) and appraisals of alcohol (negative outcome expectancies and negative implicit alcohol associations). Early sipping/tasting predicted increased frequency and quantity of alcohol consumption, and increased alcohol-related problems in late adolescence, even after controlling sociocultural and individual difference variables. Findings suggest that early sipping/tasting with parental permission is not benign and is a viable target for preventive interventions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Calculation of HNO2 concentration from redox potential in HNO3-H2O system as an aid to understanding the cathodic reaction of nitric acid corrosion

    International Nuclear Information System (INIS)

    Takeuchi, Masayuki; Whillock, G.O.H.

    2002-01-01

    Nitrous acid affects the corrosion of metals such as stainless steels in nitric acid. However nitrous acid is not particularly stable in nitric acid and the analytical methods available are quite involved. Accordingly, the calculation of nitrous acid concentration from redox potential was tested in the HNO 3 -H 2 O system as a convenient in situ analysis method. The calculation process is based on Nernst's equation and the required thermodynamic data were obtained from published values. The available thermodynamic data allow calculation of nitrous acid concentration from 273K to 373K for 0%-100% HNO 3 . The redox potential was 8 kmol·m -3 HNO 3 under NO bubbling and the nitrous acid concentration was determined by a Colourimetric method. The calculated data were compared with the measured data and a good agreement was found. It was found that the corrosion potential of stainless steel is influenced by nitrous acid concentration in nitric acid solution. The calculation process is useful for in-situ analysis of nitrous acid species in HNO 3 -H 2 O system and understanding the behavior of the cathodic reaction associated with nitric acid corrosion. (author)

  12. A strategy to calculate cyclosporin A area under the time-concentration curve in pediatric renal transplantation.

    Science.gov (United States)

    David-Neto, Elias; Araujo, Lilian Pereira; Feres Alves, Cristiane; Sumita, Nairo; Romano, Pascoalina; Yagyu, Elisa Midori; Nahas, William Carlos; Ianhez, Luiz Estevam

    2002-08-01

    The complete area under the time-concentration curve (AUC) is considered the gold standard for cyclosporin A (CsA) monitoring, particularly in pediatric kidney graft recipients who have great absorption and drug clearance variability. However, complete AUC is time-consuming and expensive. For this reason, we retrospectively reviewed 131 complete 4-h AUC (AUC0-4) performed in 34 children (mean age 10.6 +/- 2 yr) in order to construct an equation to calculate AUC0-4. The median time after transplantation was 540 (range: 247-1,358) days. Multiple regression analysis was performed either with a single variable or with a combination of two variables. CsA blood concentration at the second hour after the oral morning dose (C2) was the best predictor of AUC0-4, where AUC0-4 = 424 + (2.65 x C2), R2 = 0.81, p time-periods, C2 was the best parameter to use to calculate AUC0-4. The equations obtained during these two time-periods were very close to the one for the whole population. Our data shows that C2 can be safely used to estimate AUC0-4. However, for values above 4,000 ng/h/mL, the formula overestimates the trapezoidal AUC0-4. The C2 equation simplifies the CsA monitoring as a result of its high predictive value and clinical feasibility.

  13. Drug evaluation and the permissive principle: continuities and contradictions between standards and practices in antidepressant regulation.

    Science.gov (United States)

    Abraham, John; Davis, Courtney

    2009-08-01

    Pharmaceuticals are not permitted on to the market unless they are granted regulatory approval. The regulatory process is, therefore, crucial in whether or not a drug is widely prescribed. Regulatory agencies have developed standards of performance that pharmaceuticals are supposed to meet before entering the market. Regulation of technologies is often discussed by reference to the precautionary principle. In contrast, this paper develops the concept of the 'permissive principle' as a way of understanding the departure of regulators' practices from standards of drug efficacy to which regulatory agencies themselves subscribe. By taking a case study of antidepressant regulation in the UK and the USA, the mechanisms of permissive regulatory practices are examined. An STS methodology of both spatial (international) and temporal comparisons of regulatory practices with regulatory standards is employed to identify the nature and extent of the permissive regulation. It is found that the permissive principle was adopted by drug regulators in the UK and the USA, but more so by the former than the latter. Evidently, permissive regulation, which favours the commercial interests of the drug manufacturer, but is contrary to the interests of patients, may penetrate to the heart of regulatory science. On the other hand, permissive regulation of specific drugs should not be regarded as an inevitable result of marketing strategies and concomitant networks deployed by powerful pharmaceutical companies, because the extent of permissive regulation may vary according to the intra-institutional normative commitments of regulators to uphold their technical standards against the commercial interests of the manufacturer. Likely sociological factors that can account for such permissive regulatory practices are 'corporate bias', secrecy and excessive regulatory trust in the pharmaceutical industry in the UK, political expediency and ideological capture in the USA, combined in both countries

  14. WifiLeaks: Underestimated Privacy Implications of the ACCESS_WIFI_STATE Android Permission

    OpenAIRE

    Achara , Jagdish Prasad; Cunche , Mathieu; Roca , Vincent; Francillon , Aurélien

    2014-01-01

    A short version has been accepted for publication in: 7th ACM Conference on Security and Privacy in Wireless and Mobile Networks (WISEC'14) Oxford, United Kingdom, July 23rd -- 25th 2014; On Android, users can choose to install an application, or not, based on the permissions it requests. These permissions are later enforced on the application by the system, e.g., when accessing sensitive user data. In this work, we focus on the access to Wi-Fi related information, which is protected by the A...

  15. A permissive graphical patcher for supercollider synths

    OpenAIRE

    Dufeu, Frédéric

    2016-01-01

    This article presents the first version of a permissive graphical patcher (referred to in the text as SCPGP) dedicated to fluid interconnection and control of SuperCollider Synths. With SCPGP, the user programs her/his SynthDefs normally as code in the SuperCollider environment, along with a minimal amount of additional information on these SynthDefs, and programs Patterns according to a simple SuperCollider-compliant syntax.\\ud From the execution of this SuperCollider session, the SCPGP inte...

  16. Verification of Snapshotable Trees using Access Permissions and Typestate

    DEFF Research Database (Denmark)

    Mehnert, Hannes; Aldrich, Jonathan

    2012-01-01

    We use access permissions and typestate to specify and ver- ify a Java library that implements snapshotable search trees, as well as some client code. We formalize our approach in the Plural tool, a sound modular typestate checking tool. We describe the challenges to verify- ing snapshotable tree...

  17. Left-turn phase: permissive, protected, or both? A quasi-experimental design in New York City.

    Science.gov (United States)

    Chen, Li; Chen, Cynthia; Ewing, Reid

    2015-03-01

    The practice of left-turn phasing selection (permissive, protected-only, or both) varies from one locality to another. The literature evidence on this issue is equally mixed and insufficient. In this study, we evaluate the safety impacts of changing left-turn signal phasing from permissive to protected/permissive or protected-only at 68 intersections in New York City using a rigorous quasi-experimental design accompanied with regression modeling. Changes in police reported crashes including total crashes, multiple-vehicle crashes, left-turn crashes, pedestrian crashes and bicyclist crashes were compared between before period and after period for the treatment group and comparison group by means of negative binomial regression using a Generalized Estimating Equations (GEE) technique. Confounding factors such as the built environment characteristics that were not controlled in comparison group selection are accounted for by this approach. The results show that the change of permissive left-turn signal phasing to protected/permissive or protected-only signal phasing does not result in a significant reduction in intersection crashes. Though the protected-only signal phasing does reduce the left-turn crashes and pedestrian crashes, this reduction was offset by a possible increase in over-taking crashes. These results suggest that left-turn phasing should not be treated as a universal solution that is always better than the permissive control for left-turn vehicles. The selection and implementation of left-turn signal phasing needs to be done carefully, considering potential trade-offs between safety and delay, and many other factors such as geometry, traffic flows and operations. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. WAD, a program to calculate the heat produced by alpha decay

    International Nuclear Information System (INIS)

    Jarvis, R.G.; Bretzlaff, C.I.

    1982-09-01

    The FORTRAN program WAD (Watts from Alpha Decay) deals with the alpha and beta decay chains to be encountered in advanced fuel cycles for CANDU reactors. The data library covers all necessary alpha-emitting and beta-emitting nuclides and the program calculates the heat produced by alpha decay. Any permissible chain can be constructed very simply

  19. An Idea on the Maximum Permissible Concentrations of Radioactive Materials in Sea Water; Concentrations Maxima Admissibles des Substances Radioactives dans l'Eau de Mer; 041e 041c 0414 ; Concentracion Maxima Admisible de Materiales Radiactivos en las Aguas del Mar

    Energy Technology Data Exchange (ETDEWEB)

    Hiyama, Yoshio [University of Tokyo (Japan)

    1960-07-01

    The author of the present paper has tried to find a relationship between the level of sea-water contamination by several radionuclides and the level of the radiation dose-rate inside the human body caused by these radionuclides of marine origin, using the ICRP recommendation and the few data on the chemical analysis of sea water and of the human body at present available to the author. However, even if the idea of this calculation were to be recognized by scientists in the fields of oceanography, public health, nutrition, radiation biology, and others, it would still be necessary to get further data on the amounts of trace elements in sea-water, in marine products, and in the human body in order to complete a table of the maximum permissible concentrations in sea-water of various radionuclides. Here the idea is merely advanced and a few examples are described. (author) [French] L'auteur a cherche a etablir un rapport entre le degre de contamination de l'eau de mer par plusieurs radionuclides et le degre d'irradiation de l'interieur du corps humain due a ces radionuclides d'origine marine; a cet effet, il s'est fonde sur les recommandations de la CIPR et sur les quelques donnees relatives a l'analyse chimique de l'eau de mer et du corps humain qu'il avait a sa disposition. Cependant, meme si le principe de ce calcul etait reconnu par les oceanographes, les hygienistes, les bromatologistes, les radiobiologistes et d'autres specialistes, il n'en serait pas moins necessaire d'obtenir des renseignements supplementaires sur les quantites d'oligoelements existant dans l'eau de mer, les produits de la mer et le corps humain, en vue de dresser un tableau complet des concentrations maxima admissibles de divers radionuclides dans l'eau de mer. L'auteur se borne a formuler le concept et a donner quelques exemples. (author) [Spanish] El autor, teniendo en cuenta la recomendacion de la Comision Internacional de Proteccion Radiologica y los pocos datos de que actualmente dispone

  20. Calculation model for predicting concentrations of radioactive corrostion products in the primary coolant of boiling water reactors

    International Nuclear Information System (INIS)

    Uchida, S.; Kikuchi, M.; Asakura, Y.; Yusa, H.; Ohsumi, K.

    1978-01-01

    A calculation model was developed to predict the shutdown dose rate around the recirculation pipes and their components in boiling water reactors (BWRs) by simulating the corrosion product transport in primary cooling water. The model is characterized by separating cobalt species in the water into soluble and insoluble materials and then calculating each concentration using the following considerations: (1) Insoluble cobalt (designated as crud cobalt is deposited directly on the fuel surface, while soluble cobalt (designated as ionic cobalt) is adsorbed on iron oxide deposits on the fuel surface. (2) Cobalt-60 activated on the fuel surface is dissolved in the water in an ionic form, and some is released with iron oxide as crud. The model can follow the reduction of 60 Co in the primary cooling water caused by the control of the iron feed rate into the reactor, which decreases the iron oxide deposits on the fuel surface and then reduces the cobalt adsorption rate. The calculated results agree satisfactorily with the measurements in several BWR plants

  1. Iodine concentration calculated by dual-energy computed tomography (DECT) as a functional parameter to evaluate thyroid metabolism in patients with hyperthyroidism.

    Science.gov (United States)

    Binh, Duong Duc; Nakajima, Takahito; Otake, Hidenori; Higuchi, Tetsuya; Tsushima, Yoshito

    2017-07-19

    Thyroid function in patients with Grave's disease is usually evaluated by thyroid scintigraphy with radioactive iodine. Recently, dual-energy computed tomography (DECT) with two different energy X-rays can calculate iodine concentrations and can be applied for iodine measurements in thyroid glands. This study aimed to assess the potential use of DECT for the functional assessment of the thyroid gland. Thirteen patients with Grave's disease treated at our hospital from May to September 2015 were included in this retrospective study. Before treatments, all subjects had undergone both iodine scintigraphy [three and 24 h after oral administration of 123 I (20 μCi)] and non-enhanced DECT. The region of interests (ROIs) were placed in both lobes of the thyroid glands, and CT values (HU: Hounsfield unit) and iodine concentrations (mg/mL) calculated from DECT images were measured. The correlation between CT values and iodine concentrations from DECT in the thyroid gland was evaluated and then the iodine concentrations were compared with radioactive iodine uptake ratios by thyroid scintigraphy. Mean (±SD) 123 I uptake increased from 46.3 (±22.2) % (range, 11.1-80.1) at 3 h, to 66.5 (±15.2) % (range, 40.0-86.1) at 24 h (p hyperthyroid patients.

  2. Oligothiophene-based colorimetric and ratiometric fluorescence dual-channel cyanide chemosensor: Sensing ability, TD-DFT calculations and its application as an efficient solid state sensor

    Science.gov (United States)

    Lan, Linxin; Li, Tianduo; Wei, Tao; Pang, He; Sun, Tao; Wang, Enhua; Liu, Haixia; Niu, Qingfen

    2018-03-01

    An oligothiophene-based colorimetric and ratiometric fluorescence dual-channel cyanide chemosensor 3 T-2CN was reported. Sensor 3 T-2CN showed both naked-eye recognition and ratiometric fluorescence response for CN- with an excellent selectivity and high sensitivity. The sensing mechanism based on the nucleophilic attack of CN- on the vinyl Cdbnd C bond has been successfully confirmed by the optical measurements, 1H NMR titration, FT-IR spectra as well as the DFT/TD-DFT calculations. Moreover, the detection limit was calculated to be 0.19 μM, which is much lower than the maximum permission concentration in drinking water (1.9 μM). Importantly, test strips (filter paper and TLC plates) containing 3 T-2CN were fabricated, which could act as a practical and efficient solid state optical sensor for CN- in field measurements.

  3. Experimental verification of the imposing principle for maximum permissible levels of multicolor laser radiation

    Directory of Open Access Journals (Sweden)

    Ivashin V.A.

    2013-12-01

    Full Text Available Aims. The study presents the results of experimental research to verify the principle overlay for maximum permissible levels (MPL of multicolor laser radiation single exposure on eyes. This principle of the independence of the effects of radiation with each wavelength (the imposing principle, was founded and generalized to a wide range of exposure conditions. Experimental verification of this approach in relation to the impact of laser radiation on tissue fundus of an eye, as shows the analysis of the literature was not carried out. Material and methods. Was used in the experimental laser generating radiation with wavelengths: Л1 =0,532 microns, A2=0,556to 0,562 microns and A3=0,619to 0,621 urn. Experiments were carried out on eyes of rabbits with evenly pigmented eye bottom. Results. At comparison of results of processing of the experimental data with the calculated data it is shown that these levels are close by their parameters. Conclusions. For the first time in the Russian Federation had been performed experimental studies on the validity of multi-colored laser radiation on the organ of vision. In view of the objective coincidence of the experimental data with the calculated data, we can conclude that the mathematical formulas work.

  4. Maximum permissible concentrations of uranium in air

    CERN Document Server

    Adams, N

    1973-01-01

    The retention of uranium by bone and kidney has been re-evaluated taking account of recently published data for a man who had been occupationally exposed to natural uranium aerosols and for adults who had ingested uranium at the normal dietary levels. For life-time occupational exposure to uranium aerosols the new retention functions yield a greater retention in bone and a smaller retention in kidney than the earlier ones, which were based on acute intakes of uranium by terminal patients. Hence bone replaces kidney as the critical organ. The (MPC) sub a for uranium 238 on radiological considerations using the current (1959) ICRP lung model for the new retention functions is slightly smaller than for earlier functions but the (MPC) sub a determined by chemical toxicity remains the most restrictive.

  5. CACA-2: revised version of CACA-a heavy isotope and fission-product concentration calculational code for experimental irradiation capsules

    International Nuclear Information System (INIS)

    Allen, E.J.

    1976-02-01

    A computer program is described which calculates nuclide concentration histories, power or neutron flux histories, burnups, and fission-product birthrates for fueled experimental capsules subjected to neutron irradiations. Seventeen heavy nuclides in the chain from 232 Th to 242 Pu and a user-specified number of fission products are treated. A fourth-order Runge-Kutta calculational method solves the differential equations for nuclide concentrations as a function of time. For a particular problem, a user-specified number of fuel regions may be treated. A fuel region is described by volume, length, and specific irradiation history. A number of initial fuel compositions may be specified for each fuel region. The irradiation history for each fuel region can be divided into time intervals, and a constant power density or a time-dependent neutron flux is specified for each time interval. Also, an independent cross-section set may be selected for each time interval in each irradiation history. The fission-product birthrates for the first composition of each fuel region are summed to give the total fission-product birthrates for the problem

  6. Heavy metals concentration in various tissues of two freshwater ...

    African Journals Online (AJOL)

    Heavy metals like cadmium, zinc, copper, chromium, lead and mercury were measured in the various tissues of Labeo rohita and Channa striatus and in the water samples collected from ... The values of heavy metals concentration in the present study are within the maximum permissible levels for drinking water and fish.

  7. Corruption and the Other(s): Scope of Superordinate Identity Matters for Corruption Permissibility.

    Science.gov (United States)

    Pisor, Anne C; Gurven, Michael

    2015-01-01

    The decision to engage in corruption-public and private corruption, nepotism, and embezzlement-is often attributed to rational actors maximizing benefits to themselves. However, the importance of reciprocal relationships in humans suggests that an actor may weigh the costs of harms of her corrupt behavior to individuals who may generate future benefits for her. We hypothesize that actors who have a larger circle of actual and potential social partners will have more individuals to consider when generating harms and will thus be less likely to find corrupt acts permissible than actors with smaller circles of valued others. Using data from the World Values Survey and European Values Study (WVS), we explore whether participants with a larger geographic identity or a greater number of group memberships (i.e. a larger scope of actual and potential social partners) are less likely to find accepting bribes permissible. We find mixed support for our hypotheses, but consistently find that WVS participants with local, country, continent, or world geographic identities are less likely to find accepting a bribe permissible than those with regional identities-that is, actors whose primary identities that encompass more than their region find corruption less permissible. We discuss the importance of considering an actor's valuation of others when modeling corruption persistence, noting that establishing scopes of positive valuation is a precursor to predicting where actors will target benefits and shunt costs.

  8. Application of nomograms to calculate radiography parameters

    International Nuclear Information System (INIS)

    Voronin, S.A.; Orlov, K.P.; Petukhov, V.I.; Khomchenkov, Yu.F.; Meshalkin, I.A.; Grachev, A.V.; Akopov, V.'S.; Majorov, A.N.

    1979-01-01

    The method of calculation of radiography parameters with the help of nomograms usable for practical application under laboratory and industrial conditions, is proposed. Nomograms are developed for determining the following parameters: relative sensitivity, general non-definition of image, permissible difference of blackening density between the centre and edge of the picture (ΔD), picture contrast, focus distance, item thickness, radiation-physical parameter, dose build up factor, groove dimension and error. An experimental test has been carried out for evaluating the results, obtained with nomograms. Steel items from 25 to 79 mm thick have been subjected to testing 191 Ir has been used as a source. Comparison of calculation and experimental results has shown the discrepancy in sensitivity values, caused by ΔDsub(min) apriori index and the error, inherent in graphical plotting on a nomogram

  9. Brain intra- and extracellular sodium concentration in multiple sclerosis: a 7 T MRI study.

    Science.gov (United States)

    Petracca, Maria; Vancea, Roxana O; Fleysher, Lazar; Jonkman, Laura E; Oesingmann, Niels; Inglese, Matilde

    2016-03-01

    Intra-axonal accumulation of sodium ions is one of the key mechanisms of delayed neuro-axonal degeneration that contributes to disability accrual in multiple sclerosis. In vivo sodium magnetic resonance imaging studies have demonstrated an increase of brain total sodium concentration in patients with multiple sclerosis, especially in patients with greater disability. However, total sodium concentration is a weighted average of intra- and extra-cellular sodium concentration whose changes reflect different tissue pathophysiological processes. The in vivo, non-invasive measurement of intracellular sodium concentration is quite challenging and the few applications in patients with neurological diseases are limited to case reports and qualitative assessments. In the present study we provide first evidence of the feasibility of triple quantum filtered (23)Na magnetic resonance imaging at 7 T, and provide in vivo quantification of global and regional brain intra- and extra-cellular sodium concentration in 19 relapsing-remitting multiple sclerosis patients and 17 heathy controls. Global grey matter and white matter total sodium concentration (respectively P brain regional level, clusters of increased total sodium concentration and intracellular sodium concentration and decreased intracellular sodium volume fraction were found in several cortical, subcortical and white matter regions when patients were compared with healthy controls (P Brain. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  10. 29 CFR 3.6 - Payroll deductions permissible with the approval of the Secretary of Labor.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Payroll deductions permissible with the approval of the Secretary of Labor. 3.6 Section 3.6 Labor Office of the Secretary of Labor CONTRACTORS AND SUBCONTRACTORS ON....6 Payroll deductions permissible with the approval of the Secretary of Labor. Any contractor or...

  11. Android Apps and Permissions: Security and Privacy Risks

    OpenAIRE

    Boksasp, Trond; Utnes, Eivind

    2012-01-01

    This thesis investigates the permissions requested by Android applications, and the possibility of identifying suspicious applications based only on information presented to the user before an application is downloaded. During the course of this project, a large data set consisting of applications published on Google Play and three different third-party Android application markets was collected over a two-month period. These applications are analysed using manual pattern recognition and k-mea...

  12. Sexual and Gender Minority Adolescents' Views On HIV Research Participation and Parental Permission: A Mixed-Methods Study.

    Science.gov (United States)

    Mustanski, Brian; Coventry, Ryan; Macapagal, Kathryn; Arbeit, Miriam R; Fisher, Celia B

    2017-06-01

    Sexual and gender minority adolescents are underrepresented in HIV research, partly because institutional review boards (IRBs) are reluctant to waive parental permission requirements for these studies. Understanding teenagers' perspectives on parental permission and the risks and benefits of participating in HIV research is critical to informing evidence-based IRB decisions. Data from 74 sexual and gender minority adolescents aged 14-17 who participated in an online focus group in 2015 were used to examine perspectives on the risks and benefits of participation in a hypothetical HIV surveillance study and the need for parental permission and adequate protections. Data were analyzed thematically; mixed methods analyses examined whether concerns about parental permission differed by whether teenagers were out to their parents. Most adolescents, especially those who were not out to their parents, would be unwilling to participate in an HIV study if parental permission were required. Perceived benefits of participation included overcoming barriers to HIV testing and contributing to the health of sexual and gender minority youth. Few risks of participation were identified. Adolescents suggested steps that researchers could take to facilitate informed decision making about research participation and ensure minors' safety in the absence of parental permission; these included incorporating multimedia presentations into the consent process and explaining researchers' motivations for conducting the study. Respondents believed that the benefits of HIV surveillance research outweighed the risks. Requiring parental permission may exclude many sexual and gender minority teenagers from taking part in HIV research, especially if they are not out. Copyright © 2017 by the Guttmacher Institute.

  13. Carbon-concentrating mechanisms in seagrasses.

    Science.gov (United States)

    Larkum, Anthony William D; Davey, Peter A; Kuo, John; Ralph, Peter J; Raven, John A

    2017-06-01

    Seagrasses are unique angiosperms that carry out growth and reproduction submerged in seawater. They occur in at least three families of the Alismatales. All have chloroplasts mainly in the cells of the epidermis. Living in seawater, the supply of inorganic carbon (Ci) to the chloroplasts is diffusion limited, especially under unstirred conditions. Therefore, the supply of CO2 and bicarbonate across the diffusive boundary layer on the outer side of the epidermis is often a limiting factor. Here we discuss the evidence for mechanisms that enhance the uptake of Ci into the epidermal cells. Since bicarbonate is plentiful in seawater, a bicarbonate pump might be expected; however, the evidence for such a pump is not strongly supported. There is evidence for a carbonic anhydrase outside the outer plasmalemma. This, together with evidence for an outward proton pump, suggests the possibility that local acidification leads to enhanced concentrations of CO2 adjacent to the outer tangential epidermal walls, which enhances the uptake of CO2, and this could be followed by a carbon-concentrating mechanism (CCM) in the cytoplasm and/or chloroplasts. The lines of evidence for such an epidermal CCM are discussed, including evidence for special 'transfer cells' in some but not all seagrass leaves in the tangential inner walls of the epidermal cells. It is concluded that seagrasses have a CCM but that the case for concentration of CO2 at the site of Rubisco carboxylation is not proven. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  14. Calculations concerning the capability of passive recombiners to control hydrogen concentration in the containment of an advanced PWR

    International Nuclear Information System (INIS)

    Fineschi, F.; Vanini, P.

    1997-01-01

    The Department of Mechanical and Nuclear Constructions of the University of Pisa has developed a computer code, HOCRA, which is able to make an initial evaluation of the capability of catalytic recombiners to remove hydrogen from the atmosphere of the safety containments of nuclear reactors in accident conditions. The code allows the analysis of the average concentration transient of hydrogen in a generic compartment of a safety containment in a nuclear reactor. The software is structured into two groups. The first, mode-1, analyses the average concentration in all the free volume of the containment before a possible venting., whereas the second, mode-2, analyses the average concentration transient in a containment compartment, assuming input and output flow rates into and from the compartment itself The first part of this paper outlines the physical and mathematical model of the code, the second part reports calculations made for an advanced PWR in cooperation with ENEL. (author)

  15. Permissive cytomegalovirus infection of primary villous term and first trimester trophoblasts.

    Science.gov (United States)

    Hemmings, D G; Kilani, R; Nykiforuk, C; Preiksaitis, J; Guilbert, L J

    1998-06-01

    Forty percent of women with primary cytomegalovirus (CMV) infections during pregnancy infect their fetuses with complications for the baby varying from mild to severe. How CMV crosses the syncytiotrophoblast, the barrier between maternal blood and fetal tissue in the villous placenta, is unknown. Virus may cross by infection of maternal cells that pass through physical breaches in the syncytiotrophoblast or by direct infection of the syncytiotrophoblast, with subsequent transmission to underlying fetal placental cells. In this study, we show that pure (>99.99%), long-term and healthy (>3 weeks) cultures of syncytiotrophoblasts are permissively infected with CMV. Greater than 99% of infectious progeny virus remained cell associated throughout culture periods up to 3 weeks. Infection of term trophoblasts required a higher virus inoculum, was less efficient, and progressed more slowly than parallel infections of placental and human embryonic lung fibroblasts. Three laboratory strains (AD169, Towne, and Davis) and a clinical isolate from a congenitally infected infant all permissively infected trophoblasts, although infection efficiencies varied. The infection of first trimester syncytiotrophoblasts with strain AD169 occurred at higher frequency and progressed more rapidly than infection of term cells but less efficiently and rapidly than infection of fibroblasts. These results show that villous syncytiotrophoblasts can be permissively infected by CMV but that the infection requires high virus titers and proceeds slowly and that progeny virus remains predominantly cell associated.

  16. Tritium activity concentrations and residence times of groundwater collected in Rokkasho, Japan.

    Science.gov (United States)

    Hasegawa, Hidenao; Ueda, Shinji; Akata, Naofumi; Kakiuchi, Hideki; Hisamatsu, Shun'ichi

    2015-11-01

    Tritium ((3)H) concentrations were measured in groundwater samples from four surface wells (4-10 m deep), four shallow wells (24-26.5 m deep) and a 150-m-deep well in the Futamata River catchment area, which is adjacent to the large-scale commercial spent nuclear fuel reprocessing plant in Rokkasho, Japan. The (3)H concentrations in most of the surface- and shallow-well samples (<0.03-0.57 Bq l(-1)) were similar to those in precipitation (annual mean: 0.31-0.79 Bq l(-1)), suggesting that the residence time of the water in those wells was 0-15 y. The (3)H concentrations in the samples from a 26-m-deep well and the 150-m-deep well were lower than those in the other wells, indicating that groundwater with a long residence time exists in deep aquifers and the estuary area of the catchment. It is not clear whether (3)H released during test operation of the plant with actual spent nuclear fuel affected the (3)H concentrations observed in this study. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  17. Lead (Pb) and Zinc (Zn) Concentrations in Marine Gastropod Strombus Canarium in Johor Coastal Areas

    International Nuclear Information System (INIS)

    Shaikhah Sabri; Mohd Ismid Mohd Said; Shamila Azman

    2014-01-01

    Strombus canarium is a popular food source with high commercial value in southern part of Peninsular Malaysia. As a deposit feeder, Strombus canarium can accumulate pollutants especially heavy metals in their system. Study on this species was conducted at Teluk Sengat and Mersing, Johor where samples of seawater and Strombus canarium were collected during spring low tides around 0 to 0.2 meters. Lead (Pb) and zinc (Zn) concentrations were investigated to determine pollution status in the area. Samples from Teluk Sengat showed that Zn has higher concentration in both water and S. canarium with 0.055 mg/ L and 20.257 mg/ kg wet weight respectively. However the concentrations were within permissible limit of Malaysia Marine Water Quality Criteria and Standard (MMWQS). In contrast, Pb concentration at Teluk Sengat exceeded the MMWQS and its concentration in soft tissues of S. canarium also exceeded the permissible limit recommended by Food and Agriculture Organisation (0.5 mg/ kg wet weight) and World Health Organisation (0.2 mg/ kg wet weight). (author)

  18. Corruption and the Other(s: Scope of Superordinate Identity Matters for Corruption Permissibility.

    Directory of Open Access Journals (Sweden)

    Anne C Pisor

    Full Text Available The decision to engage in corruption-public and private corruption, nepotism, and embezzlement-is often attributed to rational actors maximizing benefits to themselves. However, the importance of reciprocal relationships in humans suggests that an actor may weigh the costs of harms of her corrupt behavior to individuals who may generate future benefits for her. We hypothesize that actors who have a larger circle of actual and potential social partners will have more individuals to consider when generating harms and will thus be less likely to find corrupt acts permissible than actors with smaller circles of valued others. Using data from the World Values Survey and European Values Study (WVS, we explore whether participants with a larger geographic identity or a greater number of group memberships (i.e. a larger scope of actual and potential social partners are less likely to find accepting bribes permissible. We find mixed support for our hypotheses, but consistently find that WVS participants with local, country, continent, or world geographic identities are less likely to find accepting a bribe permissible than those with regional identities-that is, actors whose primary identities that encompass more than their region find corruption less permissible. We discuss the importance of considering an actor's valuation of others when modeling corruption persistence, noting that establishing scopes of positive valuation is a precursor to predicting where actors will target benefits and shunt costs.

  19. Perceived realism moderates the relation between sexualized media consumption and permissive sexual attitudes in Dutch adolescents.

    Science.gov (United States)

    Baams, Laura; Overbeek, Geertjan; Dubas, Judith Semon; Doornwaard, Suzan M; Rommes, Els; van Aken, Marcel A G

    2015-04-01

    This study examined whether the development of sexualized media consumption and permissive sexual attitudes would be more strongly interrelated when adolescents perceived sexualized media images as highly realistic. We used data from a three-wave longitudinal sample of 444 Dutch adolescents aged 13-16 years at baseline. Results from parallel process latent growth modeling multigroup analyses showed that higher initial levels of sexualized media consumption were associated with higher initial level of permissive sexual attitudes. Moreover, increases of sexualized media consumption over time were associated with increases of permissive sexual attitudes over time. Considering the moderation by perceived realism, we found these effects only for those who perceived sexualized media as more realistic. Findings for male and female adolescents were similar except for the relations between initial levels and subsequent development. Among male adolescents who perceived sexualized media images to be realistic, higher initial levels of permissive sexual attitudes were related to subsequent less rapid development of sexualized media consumption. For male adolescents who perceived sexualized media to be less realistic, higher initial levels of sexualized media consumption were related to a subsequent less rapid development of permissive sexual attitudes. These relations were not found for female adolescents. Overall, our results suggest that, in male and female adolescents, those with a high level of perceived realism showed a correlated development of sexualized media consumption and permissive sexual attitudes. These findings point to a need for extended information on how to guide adolescents in interpreting and handling sexualized media in everyday life.

  20. Gender Differences in Adolescent Premarital Sexual Permissiveness in Three Asian Cities: Effects of Gender-Role Attitudes

    Science.gov (United States)

    Xiayun, Zuo; Chaohua, Lou; Ersheng, Gao; Yan, Cheng; Hongfeng, Niu; Zabin, Laurie S.

    2014-01-01

    Purpose Gender is an important factor in understanding premarital sexual attitudes and behaviors. Many studies indicate that males are more likely to initiate sexual intercourse and have more permissive perceptions about sex than females. Yet few studies have explored possible reasons for these gender differences. With samples of unmarried adolescents in three Asian cities influenced by Confucian cultures, this paper investigates the relationship between underlying gender norms and these differences in adolescents’ premarital sexual permissiveness. Methods 16,554 unmarried participants aged 15–24 were recruited in the Three-City Asian Study of Adolescents and Youth, a collaborative survey conducted in 2006–2007 in urban and rural areas of Hanoi, Shanghai and Taipei, with 6204, 6023 and 4327 from each city respectively. All of the adolescents were administered face-to-face interviews, coupled with Computer Assisted Self Interview (CASI) for sensitive questions. Scales on gender-role attitudes and on premarital sexual permissiveness for both male and female respondents were developed and applied to our analysis of the data. Multi-linear regression was used to analyze the relationship between gender-role attitudes and sexual permissiveness. Results Male respondents in each city held more permissive attitudes towards premarital sex than did females with both boys and girls expressing greater permissiveness to male premarital sexual behaviors. Boys also expressed more traditional attitudes to gender roles (condoning greater inequality) than did girls in each city. Adolescents’ gender-role attitudes and permissiveness to premarital sex varied considerably across the three cities, with the Vietnamese the most traditional, the Taiwanese the least traditional, and the adolescents in Shanghai in the middle. A negative association between traditional gender roles and premarital sexual permissiveness was only found among girls in Shanghai and Taipei. In Shanghai

  1. Adaptive Landscapes of Resistance Genes Change as Antibiotic Concentrations Change.

    Science.gov (United States)

    Mira, Portia M; Meza, Juan C; Nandipati, Anna; Barlow, Miriam

    2015-10-01

    Most studies on the evolution of antibiotic resistance are focused on selection for resistance at lethal antibiotic concentrations, which has allowed the detection of mutant strains that show strong phenotypic traits. However, solely focusing on lethal concentrations of antibiotics narrowly limits our perspective of antibiotic resistance evolution. New high-resolution competition assays have shown that resistant bacteria are selected at relatively low concentrations of antibiotics. This finding is important because sublethal concentrations of antibiotics are found widely in patients undergoing antibiotic therapies, and in nonmedical conditions such as wastewater treatment plants, and food and water used in agriculture and farming. To understand the impacts of sublethal concentrations on selection, we measured 30 adaptive landscapes for a set of TEM β-lactamases containing all combinations of the four amino acid substitutions that exist in TEM-50 for 15 β-lactam antibiotics at multiple concentrations. We found that there are many evolutionary pathways within this collection of landscapes that lead to nearly every TEM-genotype that we studied. While it is known that the pathways change depending on the type of β-lactam, this study demonstrates that the landscapes including fitness optima also change dramatically as the concentrations of antibiotics change. Based on these results we conclude that the presence of multiple concentrations of β-lactams in an environment result in many different adaptive landscapes through which pathways to nearly every genotype are available. Ultimately this may increase the diversity of genotypes in microbial populations. © The Author 2015. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  2. Evaluation of heavy metal concentrations in Rutilus frisii kutum on the southern coast of the Caspian Sea (northern Iran

    Directory of Open Access Journals (Sweden)

    Dariush Naghipour

    2016-04-01

    Full Text Available Background: Marine products, especially fish, play an increasingly significant role in human diets and health. This research evaluated the concentrations of cadmium, lead, chromium, and nickel in liver and muscle tissues of Rutilus frisii kutum along the Caspian Sea coasts of northern Iran. Methods: Thirty samples of fishes were taken from five stations (Astara, Rezvanshahr, Anazali, Ramsar, and Tonekabon during fishing season. An ICP-OES spectrophotometer was used to determine concentrations of the studied metals. Data was analyzed by SPSS 19 using descriptive statistical index, t test, and analysis of variance (ANOVA test; P Ni>Pb>Cd. The results showed statistically significant differences in the concentrations of these metals in liver and muscle tissues (P < 0.05, but no significant difference was observed between males and females. Conclusion: Based on calculations, the estimated permissible tolerable weekly intakes (PTWIs of cadmium (0.042 and 0.567 mg and lead (0.0021 and 0.027 mg in this study are lower than the levels established by the World Health Organization (WHO (0.455 mg for cadmium and 1.625 mg for lead.

  3. Data base to compare calculations and observations

    International Nuclear Information System (INIS)

    Tichler, J.L.

    1985-01-01

    Meteorological and climatological data bases were compared with known tritium release points and diffusion calculations to determine if calculated concentrations could replace measure concentrations at the monitoring stations. Daily tritium concentrations were monitored at 8 stations and 16 possible receptors. Automated data retrieval strategies are listed

  4. A Rational Threshold Signature Model and Protocol Based on Different Permissions

    Directory of Open Access Journals (Sweden)

    Bojun Wang

    2014-01-01

    Full Text Available This paper develops a novel model and protocol used in some specific scenarios, in which the participants of multiple groups with different permissions can finish the signature together. We apply the secret sharing scheme based on difference equation to the private key distribution phase and secret reconstruction phrase of our threshold signature scheme. In addition, our scheme can achieve the signature success because of the punishment strategy of the repeated rational secret sharing. Besides, the bit commitment and verification method used to detect players’ cheating behavior acts as a contributing factor to prevent the internal fraud. Using bit commitments, verifiable parameters, and time sequences, this paper constructs a dynamic game model, which has the features of threshold signature management with different permissions, cheat proof, and forward security.

  5. 11 CFR 114.15 - Permissible use of corporate and labor organization funds for certain electioneering communications.

    Science.gov (United States)

    2010-01-01

    ... 11 Federal Elections 1 2010-01-01 2010-01-01 false Permissible use of corporate and labor organization funds for certain electioneering communications. 114.15 Section 114.15 Federal Elections FEDERAL ELECTION COMMISSION GENERAL CORPORATE AND LABOR ORGANIZATION ACTIVITY § 114.15 Permissible use of corporate...

  6. Nicotine concentrations with electronic cigarette use: effects of sex and flavor.

    Science.gov (United States)

    Oncken, Cheryl A; Litt, Mark D; McLaughlin, Lynn D; Burki, Nausherwan A

    2015-04-01

    This study examined overall changes in nicotine concentrations when using a popular e-cigarette and 18 mg/mL nicotine e-Juice, and it further explored effects of sex and flavorings on these concentrations. We recruited nontreatment-seeking smokers who were willing to try e-cigarettes for 2 weeks and abstain from cigarette smoking. Subjects were randomized to either menthol tobacco or non-menthol tobacco-flavored e-cigarette use for 7-10 days, and the next week they were crossed over to the other condition. On the last day of e-cigarette use of each flavor, subjects completed a laboratory session in which they used the e-cigarette for 5 min ad libitum. Nicotine concentrations were obtained 5 min before and 5, 10, 15, 20, and 30 min after the onset of e-cigarette use. Twenty subjects completed at least 1 monitoring session. Nicotine concentrations significantly increased from baseline to 5 min by 4 ng/mL at the first laboratory session (p e-cigarette as less likeable (p e-cigarette use for 5 min, and flavor may impact nicotine concentrations with e-cigarette use in women. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  7. Boiling water reactors with Uranium-Plutonium mixed oxide fuel. Report 1: Accuracy of the nuclide concentrations calculated by CASMO-4

    International Nuclear Information System (INIS)

    Demaziere, C.

    1999-01-01

    This report is a part of the project titled 'Boiling Water Reactors With Uranium-Plutonium Mixed Oxide (MOx) Fuel'. The aim of this study is to model the impact of a core loading pattern containing MOx bundles upon the main characteristics of a BWR (reactivity coefficients, stability, etc.). The tools that are available to perform a modeling in the Department of Reactor Physics in Chalmers are CASMO-4/TABLES-3/SIMULATE-3 from Studsvik of America. These CMS (Core Management System) programs have been extensively compared with both measurements and reference codes. Nevertheless some data are proprietary in particular the comparison of the calculated nuclide concentrations versus experiments (because of the cost of this kind of experimental study). This is why this report describes such a comparative investigation carried out with a General Electric 7x7 BWR bundle. Unfortunately, since some core history parameters were unknown, a lot of hypotheses have been adopted. This invokes sometimes a significant discrepancy in the results without being able to determine the origin of the differences between calculations and experiments. Yet one can assess that, except for four nuclides - Plutonium-238, Curium-243, Curium-244 and Cesium-135 - for which the approximate power history (history effect) can be invoked, the accuracy of the calculated nuclide concentrations is rather good if one takes the numerous approximations into account

  8. The calculation of warping spools of warp-knitting machines

    Directory of Open Access Journals (Sweden)

    Vitaliy V. Chaban

    2014-12-01

    Full Text Available The paper is devoted to the development of scientific bases of the knitting machine design, in particular, to the calculation of warping spools of warp-knitting machines. The method of calculating the operating parameters of warping spools and mode of winding is offered. A formula that is obtained allows to define relationship between the parameters of the threads wound on a warping spool, their pull, structural dimensions of spool barrel and the diameter of spooling. With the given spool design and the given value of permissible tension of the material of its barrel, the offered formula allows to determine the maximum tension of the threads in the process of their winding on a spool. By this formula the safe diameter of winding the threads onto the spool can be calculated at a given pull of the threads during winding.

  9. Challenges to obtaining parental permission for child participation in a school-based waterpipe tobacco smoking prevention intervention in Qatar.

    Science.gov (United States)

    Nakkash, Rima T; Al Mulla, Ahmad; Torossian, Lena; Karhily, Roubina; Shuayb, Lama; Mahfoud, Ziyad R; Janahi, Ibrahim; Al Ansari, Al Anoud; Afifi, Rema A

    2014-09-30

    Involving children in research studies requires obtaining parental permission. A school-based intervention to delay/prevent waterpipe use for 7th and 8th graders in Qatar was developed, and parental permission requested. Fifty three percent (2308/4314) of the parents returned permission forms; of those 19.5% of the total (840/4314) granted permission. This paper describes the challenges to obtaining parental permission. No research to date has described such challenges in the Arab world. A random sample of 40 schools in Doha, Qatar was selected for inclusion in the original intervention. Permission forms were distributed to parents for approval of their child's participation. The permission forms requested that parents indicate their reasons for non-permission if they declined. These were categorized into themes. In order to understand reasons for non-permission, interviews with parents were conducted. Phone numbers of parents were requested from the school administration; 12 of the 40 schools (30%) agreed to provide the contact information. A random sample of 28 parents from 12 schools was interviewed to reach data saturation. Thematic analysis was used to analyze their responses. Reasons for non-permission documented in both the forms and interviews included: poor timing; lack of interest; the child not wanting to participate; and the child living in a smoke-free environment. Interviews provided information on important topics to include in the consent forms, parents' decision-making processes regarding their child's participation, and considerations for communicating with parents. Many parents also indicated that this was the first time they had been asked to give an informed consent for their child's participation in a study. Results indicate that more attention needs to be given to the informed parental consent process. Researchers should consider enhancing both the methods of communicating information as well the specific information provided. Before

  10. 12 CFR 714.2 - What are the permissible leasing arrangements?

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false What are the permissible leasing arrangements? 714.2 Section 714.2 Banks and Banking NATIONAL CREDIT UNION ADMINISTRATION REGULATIONS AFFECTING... leasing. In direct leasing, you purchase personal property from a vendor, becoming the owner of the...

  11. Parental feeding practices predict authoritative, authoritarian, and permissive parenting styles.

    Science.gov (United States)

    Hubbs-Tait, Laura; Kennedy, Tay Seacord; Page, Melanie C; Topham, Glade L; Harrist, Amanda W

    2008-07-01

    Our goal was to identify how parental feeding practices from the nutrition literature link to general parenting styles from the child development literature to understand how to target parenting practices to increase effectiveness of interventions. Stand-alone parental feeding practices could be targeted independently. However, parental feeding practices linked to parenting styles require interventions treating underlying family dynamics as a whole. To predict parenting styles from feeding practices and to test three hypotheses: restriction and pressure to eat are positively related whereas responsibility, monitoring, modeling, and encouraging are negatively related to an authoritarian parenting style; responsibility, monitoring, modeling, and encouraging are positively related whereas restriction and pressure to eat are negatively related to an authoritative parenting style; a permissive parenting style is negatively linked with all six feeding practices. Baseline data of a randomized-controlled intervention study. Two hundred thirty-nine parents (93.5% mothers) of first-grade children (134 boys, 105 girls) enrolled in rural public schools. Parental responses to encouraging and modeling questionnaires and the Child Feeding Questionnaire, as well as parenting styles measured by the Parenting Styles and Dimensions Questionnaire. Correlation and regression analyses. Feeding practices explained 21%, 15%, and 8% of the variance in authoritative, authoritarian, and permissive parenting, respectively. Restriction, pressure to eat, and monitoring (negative) significantly predicted an authoritarian style (Hypothesis 1); responsibility, restriction (negative), monitoring, and modeling predicted an authoritative style (Hypothesis 2); and modeling (negative) and restriction significantly predicted a permissive style (Hypothesis 3). Parental feeding practices with young children predict general parenting styles. Interventions that fail to address underlying parenting styles

  12. Calculation of depleted uranium concentration in dental fillings samples using the nuclear track detector CR-39

    International Nuclear Information System (INIS)

    Mahdi, K. H.; Subhi, A. T.; Tawfiq, N. F.

    2012-12-01

    The purpose of this study is to determine the concentration of depleted uranium in dental fillings samples, which were obtained some hospital and dental office, sale of materials deployed in Iraq. 8 samples were examined from two different fillings and lead-filling (amalgam) and composite filling (plastic). concentrations of depleted uranium were determined in these samples using a nuclear track detector CR-39 through the recording of the tracks left by of fragments of fission resulting from the reaction 2 38U (n, f). The samples are bombarded by neutrons emitted from the neutron source (2 41A m-Be) with flux of ( 10 5 n. cm- 2. s -1 ). The period of etching to show the track of fission fragments is 5 hours using NaOH solution with normalization (6.25N), and temperature (60 o C ). Concentration of depleted uranium were calculated by comparison with standard samples. The result that obtained showed that the value of the weighted average for concentration of uranium in the samples fillings (5.54± 1.05) ppm lead to thr filling (amalgam) and (5.33±0.6) ppm of the filling composite (plastic). The hazard- index, the absorbed dose and the effective dose for these concentration were determined. The obtained results of the effective dose for each of the surface of the bone and skin (as the areas most affected by this compensation industrial) is (0.56 mSv / y) for the batting lead (amalgam) and (0.54 mSv / y) for the filling composite (plastic). From the results of study it was that the highest rate is the effective dose to a specimen amalgam filling (0.68 mSv / y) which is less than the allowable limit for exposure of the general people set the World Health Organization (WHO), a (1 mSv / y). (Author)

  13. Atmospheric relative concentrations in building wakes

    International Nuclear Information System (INIS)

    Ramsdell, J.V. Jr.; Simonen, C.A.; Smyth, S.B.

    1995-05-01

    This report documents the ARCON95 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Regulatory Research for use in control room habitability assessments. The document includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON95 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more five percent of the time. These concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. Relative concentrations calculated by ARCON95 are significantly lower than concentrations calculated using the currently accepted procedure when winds are less than two meters per second. For higher wind speeds, ARCON95 calculates about the same concentrations as the current procedure

  14. Exploring Permission-Induced Risk in Android Applications for Malicious Application Detection

    KAUST Repository

    Wang, Wei; Wang, Xing; Feng, Dawei; Liu, Jiqiang; Han, Zhen; Zhang, Xiangliang

    2014-01-01

    Android has been a major target of malicious applications (malapps). How to detect and keep the malapps out of the app markets is an ongoing challenge. One of the central design points of Android security mechanism is permission control

  15. 34 CFR 222.194 - Are “in-kind” contributions permissible?

    Science.gov (United States)

    2010-07-01

    .... (b) Third party in-kind contributions mean property or services that benefit this grant program and... indirect costs, the provisions of 34 CFR 80.24 govern the allowability and valuation of in-kind contributions, except that it is permissible for a third party to contribute real property to a grantee for a...

  16. Concentration factors for fish

    International Nuclear Information System (INIS)

    Feldt, W.; Lauer, R.; Melzer, M.; Siebert, W.

    1978-01-01

    Concentration factors are defined as operators allowing to calculate the specific activity of fish meat from a given concentration of an element in the water. This parameter depends among others from the content of stable isotopes and homologues in the different waters. If this parameter is reasonably to be used for model calculations it must be referred to water with all of its content substances, these calculations also being based on this type of 'water'. (orig.) [de

  17. ESTABLISHMENT OF THE PERMISSIBLE TRAIN SPEED ON THE CURVED TURNOUTS

    Directory of Open Access Journals (Sweden)

    O. M. Patlasov

    2016-04-01

    Full Text Available Purpose. Turnouts play a key role in the railway transportation process. One-sided and many-sided curved turnouts were railed over the last 20 years in difficult conditions (curved sections, yard necks. They have a number of geometric features, unlike the conventional one-sided turnouts. Today the normative documents prohibit laying such turnouts in curved track sections and only partially regulate the assessment procedure of their real condition. The question of establishment the permissible train speed within the curved turnouts is still open. In this regard, authors propose to set the train speed according to the driving comfort criterion using the results of field measurements of ordinates from the baseline for the particular curved turnout. Methodology. The article considers the criteria using which one can set the permissible speed on the turnouts. It defines the complexity of their application, advantages and disadvantages. Findings. The work analyzes the speed distribution along the length of the real curved turnout for the forward and lateral directions. It establishes the change rate values of unbalanced accelerations for the existing norms of the curved track sections maintenance according to the difference in the adjacent bend versine at speeds up to 160 km/h. Originality. A method for establishing the trains’ speed limit within the curved turnouts was developed. It takes into account the actual geometric position in the plan of forward and lateral turnout directions. This approach makes it possible to establish a barrier places in plan on the turnouts limiting the train speed. Practical value. The proposed method makes it possible to objectively assess and set the trains’ permissible speed on the basis of the ordinate measurement of the forward and lateral directions of the curved turnouts from the baseline using the driving comfort criteria. The method was tested using real turnouts, which are located within the Pridneprovsk

  18. Swedish or American heterosexual college youth: who is more permissive?

    Science.gov (United States)

    Weinberg, M S; Lottes, I L; Shaver, F M

    1995-08-01

    Theories of human sexuality have proposed that two factors reduce the double standard of sexuality and lead to a convergence of male and female sexual behavior: the degree of social benefits and amount of power women have in basic societal institutions and the extent to which a society accepts permissive sexual norms. As these factors increase, the strength of the double standard will decrease and the convergence between male and female behaviors will increase. Compared to the United States, Sweden has instituted more policies to promote gender equality and has been thought to accept more permissive premarital sexual attitudes. The focus of the research reported here is to examine country and gender differences in sexual attitudes and sexual behavior for a sample of university students in the United States (N = 407) and Sweden (N = 570). Results indicate that Swedish students endorsed more similar sexual standards for women and men and reported more accepting attitudes than did American students. For sexual behavior, American men reported the most sexual experience, Swedish men the least, with the women of both countries generally in the middle category. Notwithstanding this more permissive behavior on the part of American men, gender convergence with respect to sexual behavior is stronger in Sweden on several of the dimensions examined: age of first engaging in partner-related sexual activities for those who were sexually experienced, relationship with first partner, number of partners both in the last year and in their lifetime, and affective reactions to first coitus. Gender convergence, however, is weaker in Sweden than in the United States with respect to the incidence and frequency of various sexual activities and the degree of satisfaction with current sex life. Findings are discussed with respect to the questions they raise about the current theories that framed this research and the differential amount of sex education provided in the two countries.

  19. Assessment of permissible low-level releases of radionuclides into the marine environment

    International Nuclear Information System (INIS)

    Kryshev, I.I.; Sazykina, T.G.

    2002-01-01

    The subject of this paper is radio-ecological assessment of permissible low-level releases of radionuclides in sea waters ensuring the radiological protection of the human population, as well as marine biota. (author)

  20. Calculating flux to predict future cave radon concentrations

    Czech Academy of Sciences Publication Activity Database

    Rowberry, Matthew David; Martí, Xavier; Frontera, C.; Van De Wiel, M.J.; Briestenský, Miloš

    2016-01-01

    Roč. 157, JUN (2016), 16-26 ISSN 0265-931X R&D Projects: GA MŠk LM2010008 Institutional support: RVO:67985891 ; RVO:68378271 Keywords : cave radon concentration * cave radon flux * cave ventilation * radioactive decay * fault slip * numerical modelling Subject RIV: DC - Siesmology, Volcanology, Earth Structure; BG - Nuclear, Atomic and Molecular Physics, Colliders (FZU-D) Impact factor: 2.310, year: 2016

  1. The analysis of results received from the programme for calculating the concentration of pollutants from vehicles with internal combustion engines on the crossroads in urban environments

    International Nuclear Information System (INIS)

    Tashevski, Done; Dimitrovski, Mile

    1995-01-01

    The analysis of results and influence of specified factors on the concentration of pollutants on the crossroads with chosen characteristic conditions has been made, on the basis of the programme for calculating the concentration of pollutants from vehicles with internal combustion engines on the crossroads in urban environments. (author)

  2. Determination of toxic and essential element concentrations in foodstuffs from local market

    International Nuclear Information System (INIS)

    Surtipanti; Suwirma; Yumiarti; June, M.; Syaifudin, S.

    1989-01-01

    Determination of toxic and essential elements concentrations in foodstuffs from local market in Jakarta. Concentration of toxic essential elements, such as, As, Hg, Cr, Pb, Cu, and Zn, in rice, corn bean, small green peas, wheat, vegetables, fruits, tea and coffee, have been determined. As, Hg, Sb, Cr, Se, and Zn, were determined using neutron activation analysis, after being irradiated at TRIGA-MARK II reactor, while Pb and Cu were determined using atomic absorption spectrophotometer. The results obtained were lower than the maximum permissible concentration allowed. (author). 8 refs

  3. Low air exchange rate causes high indoor radon concentration in energy-efficient buildings.

    Science.gov (United States)

    Vasilyev, A V; Yarmoshenko, I V; Zhukovsky, M V

    2015-06-01

    Since 1995, requirements on energy-efficient building construction were established in Russian Building Codes. In the course of time, utilisation of such technologies became prevailing, especially in multi-storey building construction. According to the results of radon survey in buildings constructed meeting new requirements on energy efficiency, radon concentration exceeds the average level in early-constructed buildings. Preponderance of the diffusion mechanism of radon entry in modern multi-storey buildings has been experimentally established. The experimental technique of the assessment of ventilation rate in dwellings under real conditions was developed. Based on estimates of average ventilation rate, it was approved that measures to increase energy efficiency lead to reduction in ventilation rate and accumulation of higher radon concentrations indoors. Obtained ventilation rate values have to be considered as extremely low. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  4. Concentrations and human health implications of heavy metals in wild aquatic organisms captured from the core area of Daya Bay's Fishery Resource Reserve, South China Sea.

    Science.gov (United States)

    Gu, Yang-Guang; Huang, Hong-Hui; Lin, Qin

    2016-07-01

    Heavy metal concentrations in edible organisms from the core area of Daya Bay's Fishery Resource Reserve, South China Sea, were determined. Samples of 14 crustacean, fish, and shellfish species were collected and analyzed. The As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn concentrations were 0.18-1.16, 0.002-0.919, 0.40-2.85, 0.07-4.10, 0.004-0.055, 0.14-1.19, 0.014-0.070, and 4.57-15.94μg/g wet weight, respectively. The As concentrations were higher than the Chinese maximum permissible levels in all of the fish and shellfish species and two crustacean species, indicating that consumption of these wild species by humans may pose health risks. However, calculations of the health risks posed to humans indicated that no significant adverse health effects would be associated with consuming these species. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Permissive Attitude Towards Drug Use, Life Satisfaction, and Continuous Drug Use Among Psychoactive Drug Users in Hong Kong.

    Science.gov (United States)

    Cheung, N Wt; Cheung, Y W; Chen, X

    2016-06-01

    To examine the effects of a permissive attitude towards regular and occasional drug use, life satisfaction, self-esteem, depression, and other psychosocial variables in the drug use of psychoactive drug users. Psychosocial factors that might affect a permissive attitude towards regular / occasional drug use and life satisfaction were further explored. We analysed data of a sample of psychoactive drug users from a longitudinal survey of psychoactive drug abusers in Hong Kong who were interviewed at 6 time points at 6-month intervals between January 2009 and December 2011. Data of the second to the sixth time points were stacked into an individual time point structure. Random-effects probit regression analysis was performed to estimate the relative contribution of the independent variables to the binary dependent variable of drug use in the last 30 days. A permissive attitude towards drug use, life satisfaction, and depression at the concurrent time point, and self-esteem at the previous time point had direct effects on drug use in the last 30 days. Interestingly, permissiveness to occasional drug use was a stronger predictor of drug use than permissiveness to regular drug use. These 2 permissive attitude variables were affected by the belief that doing extreme things shows the vitality of young people (at concurrent time point), life satisfaction (at concurrent time point), and self-esteem (at concurrent and previous time points). Life satisfaction was affected by sense of uncertainty about the future (at concurrent time point), self-esteem (at concurrent time point), depression (at both concurrent and previous time points), and being stricken by stressful events (at previous time point). A number of psychosocial factors could affect the continuation or discontinuation of drug use, as well as the permissive attitude towards regular and occasional drug use, and life satisfaction. Implications of the findings for prevention and intervention work targeted at

  6. Factors affecting neutron measurements and calculations. Part C. Trace element concentrations in granite and their impact on thermal neutron activation

    International Nuclear Information System (INIS)

    Ruehm, Werner; Huber, Thomas; Nolte, Eckehart; Kato, Kazuo; Imanaka, Tetsuji; Egbert, Stephen D.

    2005-01-01

    Trace elements such as Li, B, Sm, and Gd can, despite their low elemental concentration in mineral materials, influence thermal neutron activation in Hiroshima and Nagasaki samples, due to their high thermal neutron absorption cross sections. This was demonstrated for a granite core, where the addition of those trace elements to the elemental composition of granite reduces the production of 152 Eu by some 25% at a depth of 25 cm from the surface. If typical concentrations of those trace elements are added to DS02 reference soil, however, the production of 152 Eu one meter above ground is not changed significantly, because of the high water content of the soil. This indicates that DS02 soil represents a reasonable reference material for the air-over-ground transport calculations. It must be kept in mind, however, that the local environment of any sample investigated for thermal neutron activation might be characterized by other elemental compositions. In particular, trace element and hydrogen concentrations could be considerably different from those used for DS02 reference soil. As an example it was demonstrated that in a granite gravestone thermal neutron activation of 36 Cl close to the surface might be, in the worst case, reduced by some 30%, due to increased local granite concentration in this type of environment. Beside other parameters such as, for example, individual sample geometry, the variability of trace elements in soil might be one reason for the variability that is observed in the individual thermal neutron activation measurements (Gold 1995). It is necessary, therefore, to carefully model the exposure geometry of the exposed material, its chemical composition, and the surrounding interface materials in order to obtain the best possible agreement in comparisons between calculated and measured data for thermal neutrons. (author)

  7. 75 FR 66050 - Permissible Sharing of Client Records by Customs Brokers

    Science.gov (United States)

    2010-10-27

    .... USCBP-2010-0038] RIN 1651-AA80 Permissible Sharing of Client Records by Customs Brokers AGENCIES... the Code of Federal Regulations (CFR) pertaining to the obligations of customs brokers to keep clients' information confidential. The proposed amendment would allow brokers, upon the client's consent in a written...

  8. PROBABILISTIC APPROACH FOR THE DETERMINATION OF CUTS PERMISSIBLE BRAKING MODES ON THE GRAVITY HUMPS

    Directory of Open Access Journals (Sweden)

    Volodymyr BOBROVSKYI

    2016-03-01

    Full Text Available The paper presents the research results of cuts braking modes on the gravity humps. The objective of this paper is developing the methods for assessment of braking modes of cuts under conditions of fuzziness of their rolling properties, as well as selecting the permissible starting speed range of cuts from retardant positions. As a criterion for assessing the modes of target control of cut rolling speed, it was proposed to use an average gap size on a classification track at the established norms of probable exceeding of permissible speed of cars collision and their stop in retarders. As a criterion for evaluating the modes of interval control of cuts rolling speed, using the risk of their non-separation on the switches was proposed. Using the simulation modeling and mathematical statistics, the configuration of the range of permissible speed of cuts coming out from retardant positions has been set. The conducted researches allow simplifying the choice of cut braking modes in systems of automatic control of cut rolling speed.

  9. Permissive hypercapnia for the prevention of morbidity and mortality in mechanically ventilated newborn infants.

    Science.gov (United States)

    Woodgate, P G; Davies, M W

    2001-01-01

    Experimental animal data and uncontrolled, observational studies in human infants have suggested that hyperventilation and hypocapnia may be associated with increased pulmonary and neurodevelopmental morbidity. Protective ventilatory strategies allowing higher levels of arterial CO2 (permissive hypercapnia) are now widely used in adult critical care. The aggressive pursuit of normocapnia in ventilated newborn infants may contribute to the already present burden of lung disease. However, the safe or ideal range for PCO2 in this vulnerable population has not been established. To assess whether, in mechanically ventilated neonates, a strategy of permissive hypercapnia improves short and long term outcomes (esp. mortality, duration of respiratory support, incidence of chronic lung disease and neurodevelopmental outcome). Standard strategies of the Cochrane Neonatal Review Group were used. Searches were made of the Oxford Database of Perinatal Trials, MEDLINE, CINAHL, and Current Contents. Searches were also made of previous reviews including cross-referencing, abstracts, and conference and symposia proceedings published in Pediatric Research. All randomised controlled trials in which a strategy of permissive hypercapnia was compared with conventional strategies aimed at achieving normocapnia (or lower levels of hypercapnia) in newborn infants who are mechanically ventilated were eligible. Standard methods of the Cochrane Neonatal Review Group were used. Trials identified by the search strategy were independently reviewed by each author and assessed for eligibility and trial quality. Data were extracted separately. Differences were compared and resolved. Additional information was requested from trial authors. Only published data were available for review. Results are expressed as relative risk and risk difference for dichotomous outcomes, and weighted mean difference for continuous variables. Two trials involving 269 newborn infants were included. Meta-analysis of

  10. State-of-the-art literature review on permissive/protected left-turn control.

    Science.gov (United States)

    2013-06-01

    In spring 2010, the Illinois Department of Transportation initiated an areawide implementation to integrate the : flashing yellow arrow as the display for the left-turn permissive interval at more than 100 intersections operating : with protected/per...

  11. Accounting of possibilities of blade oscillation emergence at the calculation of operating wheel of turbomolecular vacuum pump

    International Nuclear Information System (INIS)

    Pereslavlev, A.V.

    1988-01-01

    Possibilities of blade oscillation emergence in the operating wheel of turbomolecular vacuum pump (TVP) are considered. Permissible value of safety factor for tensile strength in the operating wheel blade root section, at which the necessary fatigue limit of a material is provided for (k=2 for aluminium alloys and k=1.5 for VT-8 titanium alloy) is determined. Methods of calculating the main dimensions of blade operating wheel on the basis of the specified maximum pumping speed, taking account of possibilities of blade oscillation emergence are presented. Results of calculating the 4S max/πD 2 2 complex, characterizing maximum speed of operating wheel pumping, depending on permissible tensipn in the blade root section (σ), are given. It is shown that (σ increase above (2.5 2.7)x10 8 Pa for aluminium alloys and above ∼ 4x10 8 Pa for VT titanium alloy don't cause increase of operating wheel maximum pumping speed. 8 refs.; 6 figs

  12. 29 CFR 3.5 - Payroll deductions permissible without application to or approval of the Secretary of Labor.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Payroll deductions permissible without application to or approval of the Secretary of Labor. 3.5 Section 3.5 Labor Office of the Secretary of Labor CONTRACTORS AND... STATES § 3.5 Payroll deductions permissible without application to or approval of the Secretary of Labor...

  13. Radioactive contamination of foodstuffs: determination of permissible levels; Contamination radioactive des denrees alimentaires: determination des niveaux admissibles

    Energy Technology Data Exchange (ETDEWEB)

    Ledermann, S [Commissariat a l' Energie Atomique, Fontenay- aux-Roses (France). Centre d' Etudes Nucleaires

    1965-07-01

    In a latent air-soil contamination situation, the population would receive 80 per cent of its contamination through foodstuffs. The supervision of this food poses many problems: sampling, radionuclide dosages, etc. It is also necessary to estimate the maximum permissible concentration of radionuclides in foodstuffs, once the maximum exposure limit for the human body has been fixed. The passage of this level to the maximum concentrations is not simple since a) each radionuclide has its own particular effect on the body; b) their concentrations vary from one foodstuff to another, and c) the average amounts of foodstuffs vary from one population to another. Two methods are given here for estimating the maximum permissible concentrations in foodstuffs, together with the first diets likely to become critical when several of them are to be considered simultaneously. The results depend on the way in which the present situation can change to become critical. This evolutionary path can only be estimated approximately. Two methods are therefore given for studying the sensitivity of the results. As an example, a numerical application of these methods using data actually available is given. The data used is naturally incomplete and this will always be true. This application test indicates however two fields in which an improvement is absolutely necessary. 1 - The obtention of multiple observations (simultaneous dosage of at least 2 radionuclides in the same foodstuff, and simultaneous dosage of at least two foodstuffs for the same radionuclide); this assumes a combined effort by the various organisms; 2 - The reaching of an agreement on the dosage methods used by the various organisms since the results actually available are not comparable. (authors) [French] Dans une situation de contamination air-sol latente, la contamination des populations se ferait a 80 pour cent par l'alimentation. Surveiller cette alimentation pose des problemes complexes: echantillonnage, dosage des

  14. Procedures for permission of installation of nuclear power stations

    International Nuclear Information System (INIS)

    Narita, Yoriaki

    1980-01-01

    The locations of atomic power stations are first selected by electric power enterprises in consultation with the Ministry of International Trade and Industry or under the guidance of authorities concerned. The surveys of the climate, topography, water and plants in the planned sites and the influences of nuclear power generation to the surrounding areas are made by the enterprisers under the administrative guidance of the MITI. Secondly, the basic project shall be submitted to and decided by the Power Resource Development Council headed by the Prime Minister (Article 10, the Power Resource Development Law). The Council shall, if necessary, call for the attendance of the governors of prefectures concerned and hear their opinions (Article 11, the Law). As the third and most complicated phase, various procedures include; (a) permission of the changes of electrical facilities under the Electricity Enterprises Act; (b) authorization of the installation of reactors under the Nuclear Reactor Regulation Law; (c) permission or authorization under other regulations including the Agricultural Land Act, etc.; (d) additional procedures related to the indemnification to fishery and so forth. Finally the reactors are to be operated after receiving the certificates of the Minister of ITI on the inspections of construction works, nuclear fuel materials used for the reactors and welding processes of reactor containment vessels, boilers, turbines, etc. (Okada, K.)

  15. Particle-in-cell vs straight-line airflow Gaussian calculations of concentration and deposition of airborne emissions out to 70 km for two sites of differing meteorological and topographical character

    International Nuclear Information System (INIS)

    Lange, R.; Dickerson, M.A.; Peterson, K.R.; Sherman, C.A.; Sullivan, T.J.

    1976-01-01

    Two numerical models for the calculation of air concentration and ground deposition of airborne effluent releases are compared. The Particle-in-Cell (PIC) model and the Straight-Line Airflow Gaussian model were used for the simulation. Two sites were selected for comparison: the Hudson River Valley, New York, and the area around the Savannah River Plant, South Carolina. Input for the models was synthesized from meteorological data gathered in previous studies by various investigators. It was found that the PIC model more closely simulated the three-dimensional effects of the meteorology and topography. Overall, the Gaussian model calculated higher concentrations under stable conditions with better agreement between the two methods during neutral to unstable conditions. In addition, because of its consideration of exposure from the returning plume after flow reversal, the PIC model calculated air concentrations over larger areas than did the Gaussian model

  16. 77 FR 17367 - Permissible Sharing of Client Records by Customs Brokers

    Science.gov (United States)

    2012-03-26

    ...-0038] RIN 1651-AA80 Permissible Sharing of Client Records by Customs Brokers AGENCY: U.S. Customs and... would allow brokers, upon the client's consent in a written authorization, to share client information... services to the broker's clients. Although the proposed rule was prepared in response to a request from a...

  17. A cash flow oriented EOQ model under permissible delay in payments

    African Journals Online (AJOL)

    A cash flow oriented EOQ model under permissible delay in payments. RP Tripathi, SS Misra, HS Shukla. Abstract. This study presents an inventory model to determine an optimal ordering policy for non-deteriorating items and timedependent demand rate with delay in payments permitted by the supplier under inflation and ...

  18. A comparison of methods used to calculate normal background concentrations of potentially toxic elements for urban soil

    Energy Technology Data Exchange (ETDEWEB)

    Rothwell, Katherine A., E-mail: k.rothwell@ncl.ac.uk; Cooke, Martin P., E-mail: martin.cooke@ncl.ac.uk

    2015-11-01

    To meet the requirements of regulation and to provide realistic remedial targets there is a need for the background concentration of potentially toxic elements (PTEs) in soils to be considered when assessing contaminated land. In England, normal background concentrations (NBCs) have been published for several priority contaminants for a number of spatial domains however updated regulatory guidance places the responsibility on Local Authorities to set NBCs for their jurisdiction. Due to the unique geochemical nature of urban areas, Local Authorities need to define NBC values specific to their area, which the national data is unable to provide. This study aims to calculate NBC levels for Gateshead, an urban Metropolitan Borough in the North East of England, using freely available data. The ‘median + 2MAD’, boxplot upper whisker and English NBC (according to the method adopted by the British Geological Survey) methods were compared for test PTEs lead, arsenic and cadmium. Due to the lack of systematically collected data for Gateshead in the national soil chemistry database, the use of site investigation (SI) data collected during the planning process was investigated. 12,087 SI soil chemistry data points were incorporated into a database and 27 comparison samples were taken from undisturbed locations across Gateshead. The SI data gave high resolution coverage of the area and Mann–Whitney tests confirmed statistical similarity for the undisturbed comparison samples and the SI data. SI data was successfully used to calculate NBCs for Gateshead and the median + 2MAD method was selected as most appropriate by the Local Authority according to the precautionary principle as it consistently provided the most conservative NBC values. The use of this data set provides a freely available, high resolution source of data that can be used for a range of environmental applications. - Highlights: • The use of site investigation data is proposed for land contamination studies

  19. Low pO2 Contributes to Potential Error in Oxygen Saturation Calculations Using a Point-of-Care Assay.

    Science.gov (United States)

    Gunsolus, Ian L; Love, Sara A; Kohl, Louis P; Schmidt, Martin; Apple, Fred S

    2017-12-20

    The present study addressed the accuracy of calculated oxygen saturation (sO2) using point-of-care (POC) testing compared with measured values on a blood gas analyzer. In total, 3,323 sO2 values were measured in 1,180 patients using a CO-oximeter (ABL 800 Flex; Radiometer, Copenhagen, Denmark). Measured parameters were then used to calculate an expected sO2 for the POC method (Abbott i-STAT; Abbott POC, Princeton, NJ). Cases in which calculated sO2 differed from measured sO2 by 10% or more were analyzed. Of the 3,323 comparisons performed, 260 (8%) showed discrepancies (± ≥10%) between measured and calculated sO2 values. Ninety-four of discrepant measurements (245 of 260) occurred when pO2 was less than 50 mm Hg. pH and bicarbonate distributions shifted to lower values in discrepant vs nondiscrepant cases. Our results suggest that the likelihood of discrepant sO2 is 27% among patients with pO2 less than 50 mm Hg. Direct measurement of sO2 by CO-oximetry is strongly suggested in this clinical scenario. © American Society for Clinical Pathology, 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

  20. Calculations of electronic structure of UF6 molecule and crystal UO2 with relativistic pseudopotential

    International Nuclear Information System (INIS)

    Ehvarestov, R.A.; Panin, A.I.; Bandura, A.V.

    2008-01-01

    Account of relativistic effects on the properties of uranium hexafluoride is testified. Detailed comparison of single electron energies spectrum revealed in nonrelativistic (by Hartree-Fock method), relativistic (by Dirac-Fock method), and scalar-relativistic (using relativistic potential of atomic uranium frame) has been conducted. Optimization procedures of atomic basis in LCAO calculations of molecules and crystals permissive taking into account distortion of atomic orbitals when chemical bonding are discussed, and optimization effect of atomic basis on the results of scalar-relativistic calculations of UF 6 molecule properties is analyzed. Calculations of electronic structure and properties of UO 2 crystal having relativistic and nonrelativistic pseudopotentials have been realized [ru

  1. Relationship of apelin, procalcitonin, and fetuin-A concentrations with carotid intima-media thickness in acromegaly.

    Science.gov (United States)

    Topsakal, S; Akin, F; Turgut, S; Yaylali, G F; Herek, D; Ayada, C

    2015-07-01

    Acromegaly is characterized by excess growth hormone and insulin-like growth factor-1 concentrations. There is conflicting evidence as to whether acromegaly is associated with an increased risk of atherosclerosis. Apelin is an adipose tissue-derived peptide that may be associated with hyperinsulinemia. Fetuin-A is a hepatocyte produced plasma glycoprotein that has an important role as a calcification inhibitor. The aim of this study was to examine apelin, fetuin-A, and procalcitonin concentrations and to assess their relationship with carotid intima medial thickness (cIMT) in subjects with acromegaly. Apelin, fetuin-A, and procalcitonin serum concentrations were measured in 37 (20 inactive and 17 active) subjects with acromegaly and 30 control subjects, along with carotid intima medial thickness. The concentrations of apelin, fetuin-A, and procalcitonin were increased in subjects with acromegaly. There were significant correlations between apelin, fetuin-A, and procalcitonin in subjects with acromegaly. Carotid intima medial thickness values were similar between control subjects and subjects with acromegaly. Carotid intima medial thickness was not increased in subjects with acromegaly. It is possible that the increased apelin and fetuin-A concentrations observed play a protective role against the development of atherosclerosis in subjects with acromegaly. © The Author(s) 2015 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

  2. Assessment of effectiveness of geologic isolation systems. ARRRG and FOOD: computer programs for calculating radiation dose to man from radionuclides in the environment

    International Nuclear Information System (INIS)

    Napier, B.A.; Roswell, R.L.; Kennedy, W.E. Jr.; Strenge, D.L.

    1980-06-01

    The computer programs ARRRG and FOOD were written to facilitate the calculation of internal radiation doses to man from the radionuclides in the environment and external radiation doses from radionuclides in the environment. Using ARRRG, radiation doses to man may be calculated for radionuclides released to bodies of water from which people might obtain fish, other aquatic foods, or drinking water, and in which they might fish, swim or boat. With the FOOD program, radiation doses to man may be calculated from deposition on farm or garden soil and crops during either an atmospheric or water release of radionuclides. Deposition may be either directly from the air or from irrigation water. Fifteen crop or animal product pathways may be chosen. ARRAG and FOOD doses may be calculated for either a maximum-exposed individual or for a population group. Doses calculated are a one-year dose and a committed dose from one year of exposure. The exposure is usually considered as chronic; however, equations are included to calculate dose and dose commitment from acute (one-time) exposure. The equations for calculating internal dose and dose commitment are derived from those given by the International Commission on Radiological Protection (ICRP) for body burdens and Maximum Permissible Concentration (MPC) of each radionuclide. The radiation doses from external exposure to contaminated farm fields or shorelines are calculated assuming an infinite flat plane source of radionuclides. A factor of two is included for surface roughness. A modifying factor to compensate for finite extent is included in the shoreline calculations

  3. Assessment of effectiveness of geologic isolation systems. ARRRG and FOOD: computer programs for calculating radiation dose to man from radionuclides in the environment

    Energy Technology Data Exchange (ETDEWEB)

    Napier, B.A.; Roswell, R.L.; Kennedy, W.E. Jr.; Strenge, D.L.

    1980-06-01

    The computer programs ARRRG and FOOD were written to facilitate the calculation of internal radiation doses to man from the radionuclides in the environment and external radiation doses from radionuclides in the environment. Using ARRRG, radiation doses to man may be calculated for radionuclides released to bodies of water from which people might obtain fish, other aquatic foods, or drinking water, and in which they might fish, swim or boat. With the FOOD program, radiation doses to man may be calculated from deposition on farm or garden soil and crops during either an atmospheric or water release of radionuclides. Deposition may be either directly from the air or from irrigation water. Fifteen crop or animal product pathways may be chosen. ARRAG and FOOD doses may be calculated for either a maximum-exposed individual or for a population group. Doses calculated are a one-year dose and a committed dose from one year of exposure. The exposure is usually considered as chronic; however, equations are included to calculate dose and dose commitment from acute (one-time) exposure. The equations for calculating internal dose and dose commitment are derived from those given by the International Commission on Radiological Protection (ICRP) for body burdens and Maximum Permissible Concentration (MPC) of each radionuclide. The radiation doses from external exposure to contaminated farm fields or shorelines are calculated assuming an infinite flat plane source of radionuclides. A factor of two is included for surface roughness. A modifying factor to compensate for finite extent is included in the shoreline calculations.

  4. Concentrations of thiocyanate and goitrin in human plasma, their precursor concentrations in brassica vegetables, and associated potential risk for hypothyroidism.

    Science.gov (United States)

    Felker, Peter; Bunch, Ronald; Leung, Angela M

    2016-04-01

    Brassica vegetables are common components of the diet and have beneficial as well as potentially adverse health effects. Following enzymatic breakdown, some glucosinolates in brassica vegetables produce sulforaphane, phenethyl, and indolylic isothiocyanates that possess anticarcinogenic activity. In contrast, progoitrin and indolylic glucosinolates degrade to goitrin and thiocyanate, respectively, and may decrease thyroid hormone production. Radioiodine uptake to the thyroid is inhibited by 194 μmol of goitrin, but not by 77 μmol of goitrin. Collards, Brussels sprouts, and some Russian kale (Brassica napus) contain sufficient goitrin to potentially decrease iodine uptake by the thyroid. However, turnip tops, commercial broccoli, broccoli rabe, and kale belonging to Brassica oleracae contain less than 10 μmol of goitrin per 100-g serving and can be considered of minimal risk. Using sulforaphane plasma levels following glucoraphanin ingestion as a surrogate for thiocyanate plasma concentrations after indole glucosinolate ingestion, the maximum thiocyanate contribution from indole glucosinolate degradation is estimated to be 10 μM, which is significantly lower than background plasma thiocyanate concentrations (40-69 μM). Thiocyanate generated from consumption of indole glucosinolate can be assumed to have minimal adverse risks for thyroid health. © The Author(s) 2016. Published by Oxford University Press on behalf of the International Life Sciences Institute. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  5. RADON CONCENTRATION TIME SERIES MODELING AND APPLICATION DISCUSSION.

    Science.gov (United States)

    Stránský, V; Thinová, L

    2017-11-01

    In the year 2010 a continual radon measurement was established at Mladeč Caves in the Czech Republic using a continual radon monitor RADIM3A. In order to model radon time series in the years 2010-15, the Box-Jenkins Methodology, often used in econometrics, was applied. Because of the behavior of radon concentrations (RCs), a seasonal integrated, autoregressive moving averages model with exogenous variables (SARIMAX) has been chosen to model the measured time series. This model uses the time series seasonality, previously acquired values and delayed atmospheric parameters, to forecast RC. The developed model for RC time series is called regARIMA(5,1,3). Model residuals could be retrospectively compared with seismic evidence of local or global earthquakes, which occurred during the RCs measurement. This technique enables us to asses if continuously measured RC could serve an earthquake precursor. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  6. Mycobacteria exploit nitric oxide-induced transformation of macrophages into permissive giant cells.

    Science.gov (United States)

    Gharun, Kourosh; Senges, Julia; Seidl, Maximilian; Lösslein, Anne; Kolter, Julia; Lohrmann, Florens; Fliegauf, Manfred; Elgizouli, Magdeldin; Vavra, Martina; Schachtrup, Kristina; Illert, Anna L; Gilleron, Martine; Kirschning, Carsten J; Triantafyllopoulou, Antigoni; Henneke, Philipp

    2017-12-01

    Immunity to mycobacteria involves the formation of granulomas, characterized by a unique macrophage (MΦ) species, so-called multinucleated giant cells (MGC). It remains unresolved whether MGC are beneficial to the host, that is, by prevention of bacterial spread, or whether they promote mycobacterial persistence. Here, we show that the prototypical antimycobacterial molecule nitric oxide (NO), which is produced by MGC in excessive amounts, is a double-edged sword. Next to its antibacterial capacity, NO propagates the transformation of MΦ into MGC, which are relatively permissive for mycobacterial persistence. The mechanism underlying MGC formation involves NO-induced DNA damage and impairment of p53 function. Moreover, MGC have an unsurpassed potential to engulf mycobacteria-infected apoptotic cells, which adds a further burden to their antimycobacterial capacity. Accordingly, mycobacteria take paradoxical advantage of antimicrobial cellular efforts by driving effector MΦ into a permissive MGC state. © 2017 The Authors.

  7. Permissiveness toward divorce : The influence of divorce experiences in three social contexts

    NARCIS (Netherlands)

    Sieben, I.J.P.; Verbakel, C.M.C.

    2013-01-01

    In this study, we assess whether divorce experiences in three social contexts shape individual’s permissiveness toward divorce. Using European Values Study data from 44 countries, we find that—net of personal divorce experience—parental divorce before the age of 18 (socialization context); parental

  8. Permissiveness toward divorce: The influence of divorce experiences in three social contexts

    NARCIS (Netherlands)

    Sieben, I.J.P.; Verbakel, C.M.C.

    2013-01-01

    In this study, we assess whether divorce experiences in three social contexts shape individual’s permissiveness toward divorce. Using European Values Study data from 44 countries, we find that—net of personal divorce experience—parental divorce before the age of 18 (socialization context); parental

  9. Permissive weight bearing in trauma patients with fracture of the lower extremities: prospective multicenter comparative cohort study.

    Science.gov (United States)

    Kalmet, Pishtiwan H S; Meys, Guido; V Horn, Yvette Y; Evers, Silvia M A A; Seelen, Henk A M; Hustinx, Paul; Janzing, Heinrich; Vd Veen, Alexander; Jaspars, Coen; Sintenie, Jan Bernard; Blokhuis, Taco J; Poeze, Martijn; Brink, Peter R G

    2018-02-02

    The standard aftercare treatment in surgically treated trauma patients with fractures around or in a joint, known as (peri)- or intra-articular fractures of the lower extremities, is either non-weight bearing or partial weight bearing. We have developed an early permissive weight bearing post-surgery rehabilitation protocol in surgically treated patients with fractures of the lower extremities. In this proposal we want to compare our early permissive weight bearing protocol to the existing current non-weight bearing guidelines in a prospective comparative cohort study. The study is a prospective multicenter comparative cohort study in which two rehabilitation aftercare treatments will be contrasted, i.e. permissive weight bearing and non-weight bearing according to the AO-guideline. The study population consists of patients with a surgically treated fracture of the pelvis/acetabulum or a surgically treated (peri)- or intra-articular fracture of the lower extremities. The inclusion period is 12 months. The duration of follow up is 6 months, with measurements taken at baseline, 2,6,12 and 26 weeks post-surgery. ADL with Lower Extremity Functional Scale. Outcome variables for compliance, as measured with an insole pressure measurement system, encompass peak load and step duration. This study will investigate the (cost-) effectiveness of a permissive weight bearing aftercare protocol. The results will provide evidence whether a permissive weight bearing protocol is more effective than the current non-weight bearing protocol. The study is registered in the Dutch Trial Register ( NTR6077 ). Date of registration: 01-09-2016.

  10. Concentration of some radionuclides in some popular sudanese medicinal plants

    International Nuclear Information System (INIS)

    Sagiroun, M. I. A.

    2012-10-01

    In this study was measured concentration of naturally occurring radionuclides 2 38U , 2 32T h and 4 0K in samples of sudanese medicinal plants. The radionuclide activity concentrations in samples analyzed ranged from 4.09 to 41.07 Bq kg -1 for 2 38T h and from 353.14 to 2270.21 Bq kg -1 for 4 0k . No trace of artificial radionuclide was determined in all the samples. The effective dose due to the presence of these radionuclides was estimated and found to be 0.524 mSv/year which is well below the permissible levels. (Author)

  11. Larval diet affects mosquito development and permissiveness to Plasmodium infection.

    Science.gov (United States)

    Linenberg, Inbar; Christophides, George K; Gendrin, Mathilde

    2016-12-02

    The larval stages of malaria vector mosquitoes develop in water pools, feeding mostly on microorganisms and environmental detritus. Richness in the nutrient supply to larvae influences the development and metabolism of larvae and adults. Here, we investigated the effects of larval diet on the development, microbiota content and permissiveness to Plasmodium of Anopheles coluzzii. We tested three fish diets often used to rear mosquitoes in the laboratory, including two pelleted diets, Dr. Clarke's Pool Pellets and Nishikoi Fish Pellets, and one flaked diet, Tetramin Fish-Flakes. Larvae grow and develop faster and produce bigger adults when feeding on both types of pellets compared with flakes. This correlates with a higher microbiota load in pellet-fed larvae, in agreement with the known positive effect of the microbiota on mosquito development. Larval diet also significantly influences the prevalence and intensity of Plasmodium berghei infection in adults, whereby Nishikoi Fish Pellets-fed larvae develop into adults that are highly permissive to parasites and survive longer after infection. This correlates with a lower amount of Enterobacteriaceae in the midgut microbiota. Together, our results shed light on the influence of larval feeding on mosquito development, microbiota and vector competence; they also provide useful data for mosquito rearing.

  12. A new method for calculating number concentrations of cloud condensation nuclei based on measurements of a three-wavelength humidified nephelometer system

    Science.gov (United States)

    Tao, Jiangchuan; Zhao, Chunsheng; Kuang, Ye; Zhao, Gang; Shen, Chuanyang; Yu, Yingli; Bian, Yuxuan; Xu, Wanyun

    2018-02-01

    The number concentration of cloud condensation nuclei (CCN) plays a fundamental role in cloud physics. Instrumentations of direct measurements of CCN number concentration (NCCN) based on chamber technology are complex and costly; thus a simple way for measuring NCCN is needed. In this study, a new method for NCCN calculation based on measurements of a three-wavelength humidified nephelometer system is proposed. A three-wavelength humidified nephelometer system can measure the aerosol light-scattering coefficient (σsp) at three wavelengths and the light-scattering enhancement factor (fRH). The Ångström exponent (Å) inferred from σsp at three wavelengths provides information on mean predominate aerosol size, and hygroscopicity parameter (κ) can be calculated from the combination of fRH and Å. Given this, a lookup table that includes σsp, κ and Å is established to predict NCCN. Due to the precondition for the application, this new method is not suitable for externally mixed particles, large particles (e.g., dust and sea salt) or fresh aerosol particles. This method is validated with direct measurements of NCCN using a CCN counter on the North China Plain. Results show that relative deviations between calculated NCCN and measured NCCN are within 30 % and confirm the robustness of this method. This method enables simplerNCCN measurements because the humidified nephelometer system is easily operated and stable. Compared with the method using a CCN counter, another advantage of this newly proposed method is that it can obtain NCCN at lower supersaturations in the ambient atmosphere.

  13. Calcium and Strontium in Swedish Waters and Fish, and Accumulation of Strontium-90

    Energy Technology Data Exchange (ETDEWEB)

    Agnedal, P O

    1966-04-15

    The purpose of this study has been to investigate the correlation between calcium and strontium in fish in relation to the concentration of these elements in the water. An investigation of the uptake of strontium-90 has also been made and permissible levels of strontium-90 in the water is calculated based upon the uptake in fish muscle tissues. Lakes with calcium concentrations between 2 - 63 mg/l have been studied and samples from the Baltic coastal water are also included. Three fish species are studied, viz. pike (Esox lucius (L.)), perch (Perca fluviatilis (L.)) and roach (Leuciscus rutilus (L.)). Bones, muscle tissues and skin + scales have been analysed. Strontium-90 measurements have been made showing an increase in both water and fish. Calculations show that in water with about 2 mg Ca/l a 10-fold increase of the existing strontium-90 level might give strontium-90 concentrations in fish muscle tissues close to what is permissible. In lakes with calcium concentrations 20 - 40 mg/l the permissible levels for drinking water will be exceeded before the fish consumption would have to be restricted.

  14. Calcium and Strontium in Swedish Waters and Fish, and Accumulation of Strontium-90

    International Nuclear Information System (INIS)

    Agnedal, P.O.

    1966-04-01

    The purpose of this study has been to investigate the correlation between calcium and strontium in fish in relation to the concentration of these elements in the water. An investigation of the uptake of strontium-90 has also been made and permissible levels of strontium-90 in the water is calculated based upon the uptake in fish muscle tissues. Lakes with calcium concentrations between 2 - 63 mg/l have been studied and samples from the Baltic coastal water are also included. Three fish species are studied, viz. pike (Esox lucius (L.)), perch (Perca fluviatilis (L.)) and roach (Leuciscus rutilus (L.)). Bones, muscle tissues and skin + scales have been analysed. Strontium-90 measurements have been made showing an increase in both water and fish. Calculations show that in water with about 2 mg Ca/l a 10-fold increase of the existing strontium-90 level might give strontium-90 concentrations in fish muscle tissues close to what is permissible. In lakes with calcium concentrations 20 - 40 mg/l the permissible levels for drinking water will be exceeded before the fish consumption would have to be restricted

  15. Flexing the PECs: Predicting environmental concentrations of veterinary drugs in Canadian agricultural soils.

    Science.gov (United States)

    Kullik, Sigrun A; Belknap, Andrew M

    2017-03-01

    Veterinary drugs administered to food animals primarily enter ecosystems through the application of livestock waste to agricultural land. Although veterinary drugs are essential for protecting animal health, their entry into the environment may pose a risk for nontarget organisms. A means to predict environmental concentrations of new veterinary drug ingredients in soil is required to assess their environmental fate, distribution, and potential effects. The Canadian predicted environmental concentrations in soil (PECsoil) for new veterinary drug ingredients for use in intensively reared animals is based on the approach currently used by the European Medicines Agency for VICH Phase I environmental assessments. The calculation for the European Medicines Agency PECsoil can be adapted to account for regional animal husbandry and land use practices. Canadian agricultural practices for intensively reared cattle, pigs, and poultry differ substantially from those in the European Union. The development of PECsoil default values and livestock categories representative of typical Canadian animal production methods and nutrient management practices culminates several years of research and an extensive survey and analysis of the scientific literature, Canadian agricultural statistics, national and provincial management recommendations, veterinary product databases, and producers. A PECsoil can be used to rapidly identify new veterinary drugs intended for intensive livestock production that should undergo targeted ecotoxicity and fate testing. The Canadian PECsoil model is readily available, transparent, and requires minimal inputs to generate a screening level environmental assessment for veterinary drugs that can be refined if additional data are available. PECsoil values for a hypothetical veterinary drug dosage regimen are presented and discussed in an international context. Integr Environ Assess Manag 2017;13:331-341. © 2016 Her Majesty the Queen in Right of Canada

  16. Larval diet affects mosquito development and permissiveness to Plasmodium infection

    OpenAIRE

    Gendrin, MEM; Christophides; Linenberg, Inbar

    2016-01-01

    The larval stages of malaria vector mosquitoes develop in water pools, feeding mostly on microorganisms and environmental detritus. Richness in the nutrient supply to larvae influences the development and metabolism of larvae and adults. Here, we investigated the effects of larval diet on the development, microbiota content and permissiveness to Plasmodium of Anopheles coluzzii . We tested three fish diets often used to rear mosquitoes in the laboratory, including two pelleted diets, Dr. Clar...

  17. Analysis of Co, Cr and Mn Concentrations in Atmospheric Dry Deposition in Hamadan City

    Directory of Open Access Journals (Sweden)

    P. Shokri Ragheb

    2016-07-01

    Full Text Available Introduction & Objective: Heavy metals are major pollutants that can spread in the atmosphere with particulate matter and dust and because of the toxic and carcinogenic effects, their meas-urement and control is very important. Therefore, this study was conducted to assess Co, Cr and Mn concentration in the atmospheric dry deposition collected from Hamadan city in 2014. Materials & Methods: After collection of 12 dust samples from 3 sampling stations and their laboratory preparation, metals concentrations were determined using ICP–OES. All statistical analyses were performed using the SPSS statistical package. Results: The results showed that the minimum and maximum mean concentrations of Co were 0.19 and 0.29 mg/kg for high and low traffic intensity sampling stations, respectively. The min and max mean concentrations of Cr were 0.65and 1.02 mg/kg for high traffic intensity and suburb sampling stations, respectively and the min and max mean concentrations of Mn were 7.23and 8.82 mg/kg for high and low traffic intensity sampling stations , respectively. Also comparing the mean concentrations of assessed metals with WHO permissible limits showed a significant difference (P< 0.05. The mean concentrations of metals were signifi-cantly lower than the maximum permissible limits. Conclusion: Although the mean concentrations of Co, Cr and Mn are lower than the standard levels, lack of continuous monitoring of heavy metals concentrations in the dust and particu-late matters in the air can lead to the entrance of various types of toxic pollutants such as heavy metals into the air and result in adverse health effects. (Sci J Hamadan Univ Med Sci 2016; 23 (2:149-156

  18. Permissive and instructive anterior patterning rely on mRNA localization in the wasp embryo.

    Science.gov (United States)

    Brent, Ava E; Yucel, Gozde; Small, Stephen; Desplan, Claude

    2007-03-30

    The long-germ mode of embryogenesis, in which segments arise simultaneously along the anteriorposterior axis, has evolved several times in different lineages of the holometabolous, or fully metamorphosing, insects. Drosophila's long-germ fate map is established largely by the activity of the dipteran-specific Bicoid (Bcd) morphogen gradient, which operates both instructively and permissively to accomplish anterior patterning. By contrast, all nondipteran long-germ insects must achieve anterior patterning independently of bcd. We show that bcd's permissive function is mimicked in the wasp by a maternal repression system in which anterior localization of the wasp ortholog of giant represses anterior expression of the trunk gap genes so that head and thorax can properly form.

  19. Indoor radon concentration in Poland

    International Nuclear Information System (INIS)

    Mamont-Ciesla, K.; Jagielak, J.; Rosinski, S.W.; Sosinka, A.; Bysiek, M.; Henschke, J.

    1996-01-01

    Preliminary survey of Rn concentration indoors by means of track detectors and y-ray dose rate with the use of TLD in almost 500 homes in selected areas of Poland was performed in the late 1980s. It was concluded that radon contributes 1.16 mSv i.e. about 46 per cent of the total natural environment ionizing radiation dose to the Polish population. Comparison of the average radon concentrations in 4 seasons of a year and in 3 groups of buildings: masonry, concrete and wood, revealed that the ground beneath the building structure is likely the dominant source of radon indoors. Since the National Atomic Energy Agency in its regulations of 1988-03-31 set up the permissible limit of the equilibrium equivalent concentration of radon in new buildings (equal 100 Bq/m3), the nation-scale survey project for radon in buildings has been undertaken. These regulations were supposed to take effect in 1995-01-01. The project has 3 objectives: to estimate the radiation exposure due to radon daughters received by Polish population to identify radon-prone areas in Poland to investigate dependence of the indoor radon concentrations on such parameters as: type of construction material, presence (or absence) of cellar under the building, number of floor

  20. Determination of free cyanide and total cyanide concentrations in surface and underground waters in Bogoso and its surrounding areas in Ghana

    Directory of Open Access Journals (Sweden)

    S. Obiri

    2007-08-01

    Full Text Available Concentrations of free cyanide and total cyanide in water samples in Bogoso and its surrounding areas in Ghana have been measured in this study. Concentrations of free cyanide and total cyanide were found to be above the maximum permissible discharge limit of effluent from mining companies into natural waters set by Environmental Protection Agency, Ghana (GEPA. A comparison of the results obtained in this study with permissible levels set by US Environmental Protection Agency and the World Health Organization reveals that surface waters in the study areas are highly polluted with cyanide and it's not safe for human consumptions. This means that, the resident in and around Bogoso are at risk.

  1. CALCULATION OF FLUENCE-TO-EFFECTIVE DOSE CONVERSION COEFFICIENTS FOR THE OPERATIONAL QUANTITY PROPOSED BY ICRU RC26.

    Science.gov (United States)

    Endo, Akira

    2017-07-01

    Fluence-to-effective dose conversion coefficients have been calculated for photons, neutrons, electrons, positrons, protons, muons, pions and helium ions for various incident angles of radiations. The aim of this calculation is to provide a set of conversion coefficients to the Report Committee 26 (RC26) of the International Commission on Radiation Units and Measurements (ICRU) for use in defining personal dose equivalent for individual monitoring. The data sets comprise effective dose conversion coefficients for incident angles of radiations from 0° to ±90° in steps of 15° and at ±180°. Conversion coefficients for rotational, isotropic, superior hemisphere semi-isotropic and inferior hemisphere semi-isotropic irradiations are also included. Numerical data of the conversion coefficients are presented as supplementary data. The conversion coefficients are used to define the personal dose equivalent, which is being considered by the ICRU RC26, as the operational quantity for individual monitoring. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  2. Effect of boron and gadolinium concentration on the calculated neutron multiplication factor of U(3)O2 fuel pins in optimum geometries

    International Nuclear Information System (INIS)

    Thomas, J.T.

    1984-10-01

    The KENO-Va improved Monte Carlo criticality program is used to calculate the neutron multiplication factor for TMI-U2 fuel compositions in a variety of configurations and to display parametric regions giving rise to maximum reactivity contributions. The lattice pitch of UO 2 fuel pins producing a maximum k/sub eff/ is determined as a function of boron concentrations in the coolant for infinite and finite systems. The characteristics of U 3 O 8 -coolant mixtures of interest to modeling the rubble region of the core are presented. Several disrupted core configurations are calculated and comparisons made. The results should be useful to proposed defueling of the TMI-U2 reactor

  3. Primary Human Placental Trophoblasts are Permissive for Zika Virus (ZIKV) Replication.

    Science.gov (United States)

    Aagaard, Kjersti M; Lahon, Anismrita; Suter, Melissa A; Arya, Ravi P; Seferovic, Maxim D; Vogt, Megan B; Hu, Min; Stossi, Fabio; Mancini, Michael A; Harris, R Alan; Kahr, Maike; Eppes, Catherine; Rac, Martha; Belfort, Michael A; Park, Chun Shik; Lacorazza, Daniel; Rico-Hesse, Rebecca

    2017-01-27

    Zika virus (ZIKV) is an emerging mosquito-borne (Aedes genus) arbovirus of the Flaviviridae family. Although ZIKV has been predominately associated with a mild or asymptomatic dengue-like disease, its appearance in the Americas has been accompanied by a multi-fold increase in reported incidence of fetal microcephaly and brain malformations. The source and mode of vertical transmission from mother to fetus is presumptively transplacental, although a causal link explaining the interval delay between maternal symptoms and observed fetal malformations following infection has been missing. In this study, we show that primary human placental trophoblasts from non-exposed donors (n = 20) can be infected by primary passage ZIKV-FLR isolate, and uniquely allowed for ZIKV viral RNA replication when compared to dengue virus (DENV). Consistent with their being permissive for ZIKV infection, primary trophoblasts expressed multiple putative ZIKV cell entry receptors, and cellular function and differentiation were preserved. These findings suggest that ZIKV-FLR strain can replicate in human placental trophoblasts without host cell destruction, thereby serving as a likely permissive reservoir and portal of fetal transmission with risk of latent microcephaly and malformations.

  4. ESCLOUD: A computer program to calculate the air concentration, deposition rate and external dose rate from a continuous discharge of radioactive material to atmosphere

    International Nuclear Information System (INIS)

    Jones, J.A.

    1980-03-01

    Radioactive material may be discharged to atmosphere in small quantities during the normal operation of a nuclear installation as part of a considered waste management practice. Estimates of the individual and collective dose equivalent rates resulting from such a discharge are required in a number of contexts: for example, in assessing compliance with dose limits, in estimating the radiological impact of the discharge and as an input into optimisation studies. The suite of programs which has been developed to undertake such calculations is made up of a number of independent modules one of which, ESCLOUD, is described in this report. The ESCLOUD program evaluates, as a function of distance and direction from the release point, the air concentration, deposition rate and external β and γ doses from airborne and deposited activity. The air concentration and deposition rate can be used as input to other modules for calculating inhalation and ingestion doses. (author)

  5. The Impact of Different Permissible Exposure Limits on Hearing Threshold Levels Beyond 25 dBA.

    Science.gov (United States)

    Sayapathi, Balachandar S; Su, Anselm Ting; Koh, David

    2014-10-01

    Development of noise-induced hearing loss is reliant on a few factors such as frequency, intensity, and duration of noise exposure. The occurrence of this occupational malady has doubled from 120 million to 250 million in a decade. Countries such as Malaysia, India, and the US have adopted 90 dBA as the permissible exposure limit. According to the US Occupational Safety and Health Administration (OSHA), the exposure limit for noise is 90 dBA, while that of the US National Institute of Occupational Safety and Health (NIOSH) is 85 dBA for 8 hours of noise exposure. This study aimed to assess the development of hearing threshold levels beyond 25 dBA on adoption of 85 dBA as the permissible exposure limit compared to 90 dBA. This is an intervention study done on two automobile factories. There were 203 employees exposed to noise levels beyond the action level. Hearing protection devices were distributed to reduce noise levels to a level between the permissible exposure limit and action level. The permissible exposure limits were 90 and 85 dBA in factories 1 and 2, respectively, while the action levels were 85 and 80 dBA, respectively. The hearing threshold levels of participants were measured at baseline and at first month of postshift exposure of noise. The outcome was measured by a manual audiometer. McNemar and chi-square tests were used in the statistical analysis. We found that hearing threshold levels of more than 25 dBA has changed significantly from pre-intervention to post-intervention among participants from both factories (3000 Hz for the right ear and 2000 Hz for the left ear). There was a statistically significant association between participants at 3000 Hz on the right ear at 'deteriorated' level ( χ² (1) = 4.08, φ = - 0.142, P = 0.043), whereas there was worsening of hearing threshold beyond 25 dBA among those embraced 90 dBA. The adoption of 85 dBA as the permissible exposure limit has preserved hearing threshold level among participants at 3000 Hz

  6. Determination of particle concentrations in multitemperature plasmas

    International Nuclear Information System (INIS)

    Richley, E.; Tuma, D.T.

    1982-01-01

    The use of the multitemperature Saha equation (MSE) of Prigogine 1 and Patapov 2 for calculating particle concentrations in plasmas is shown to be an invalid procedure. Errors greater than one order of magnitude in the electron density in high-pressure argon and nitrogen electric arc plasmas can be easily incurred by using the multitemperature Saha equation. The alternative kinetic method for calculating concentrations is shown to be based on firm concepts. Simpliying procedures and computational techniques for calculating concentrations with the kinetic method are illustrated with examples

  7. Designing generalized conic concentrators for conventional optical systems

    Science.gov (United States)

    Eichhorn, W. L.

    1985-01-01

    Generalized nonimaging concentrators can be incorporated into conventional optical systems in situations where flux concentration rather than imaging is required. The parameters of the concentrator for maximum flux concentration depend on the design of the particular optical system under consideration. Rationale for determining the concentrator parameters is given for one particular optical system and the procedure used for calculation of these parameters is outlined. The calculations are done for three concentrators applicable to the optical system.

  8. Student Learning with Permissive and Restrictive Cell Phone Policies: A Classroom Experiment

    Science.gov (United States)

    Lancaster, Alexander L.

    2018-01-01

    Based on Finn and Ledbetter's (2013; 2014) work regarding classroom technology policies, this experimental study examined the implementation of a permissive and a restrictive cellular phone policy and the effect of these policies on students' cognitive and affective learning in two sections of a public speaking course. College students (N = 31)…

  9. Calculation and analysis of hydrogen volume concentrations in the vent pipe rigid proposed for NPP-L V

    International Nuclear Information System (INIS)

    Gomez T, A. M.; Xolocostli M, V.; Lopez M, R.; Filio L, C.; Royl, P.

    2014-10-01

    In 2012 was modeled of primary and secondary container of the nuclear power plant of Laguna Verde (NPP-L V) for the CFD Gas-Flow code. These models were used to calculate hydrogen volume concentrations run release the reactor building in case of a severe accident. The results showed that the venting would produce detonation conditions in the venting level (level 33) and flammability at ground level of reload. One of the solutions to avoid reaching critical concentrations (flammable or detonable) inside the reactor building and thus safeguard the contentions is to make a rigid venting. The rigid vent is a pipe connected to the primary container could go to the level 33 of the secondary container and style fireplace climb to the top of the reactor building. The analysis of hydrogen transport inside the vent pipe can be influenced by various environmental criteria and factors vent, so a logical consequence of the 2012 analysis is the analysis of the gases transport within said pipe to define vent ideal conditions. For these evaluations the vent pipe was modeled with a fine mesh of 32 radial interior nodes and a coarse mesh of 4 radial interior nodes. With three-dimensional models were realized calculations that allow observing the influence of heat transfer in the long term, i.e. a complete analysis of exhaust (approx. 700 seconds). However, the most interesting results focus on the first milliseconds, when the H 2 coming from the atmosphere of the primary container faces the air in the vent pipe. These first milliseconds besides allowing evaluating the detonation criteria in great detail in the different tubular sections similarly allow evaluating the pressure wave that occurs in the pipe and that at some point slows to the fluid on the last tubular section and could produce a detonation inside the pipe. Results are presented for venting fixed conditions, showing possible detonations into the pipe. (Author)

  10. Ecological imperatives for aquatic CO2-concentrating mechanisms.

    Science.gov (United States)

    Maberly, Stephen C; Gontero, Brigitte

    2017-06-01

    In aquatic environments, the concentration of inorganic carbon is spatially and temporally variable and CO2 can be substantially oversaturated or depleted. Depletion of CO2 plus low rates of diffusion cause inorganic carbon to be more limiting in aquatic than terrestrial environments, and the frequency of species with a CO2-concentrating mechanism (CCM), and their contribution to productivity, is correspondingly greater. Aquatic photoautotrophs may have biochemical or biophysical CCMs and exploit CO2 from the sediment or the atmosphere. Though partly constrained by phylogeny, CCM activity is related to environmental conditions. CCMs are absent or down-regulated when their increased energy costs, lower CO2 affinity, or altered mineral requirements outweigh their benefits. Aquatic CCMs are most widespread in environments with low CO2, high HCO3-, high pH, and high light. Freshwater species are generally less effective at inorganic carbon removal than marine species, but have a greater range of ability to remove carbon, matching the environmental variability in carbon availability. The diversity of CCMs in seagrasses and marine phytoplankton, and detailed mechanistic studies on larger aquatic photoautotrophs are understudied. Strengthening the links between ecology and CCMs will increase our understanding of the mechanisms underlying ecological success and will place mechanistic studies in a clearer ecological context. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  11. Use of the theory of recognition of patterns in developing methane metering equipment for blow-out-dangerous mines. [Instrument recognizes rate of change of methane concentration and, if dangerous, shuts off electrical equipment

    Energy Technology Data Exchange (ETDEWEB)

    Medvedev, V N

    1978-01-01

    In the most general form, the existing methane-metering equipment which issues command signals when the maximum permissible value of methane concentration has been reached can be viewed as a recognition system. The algorithm for operation on the principle of evaluating the degree of blow-out danger of the ore atmosphere stipulates the recognition of two situations: 1) ''not dangerous ''(methane concentration below maximum permissible value); 2) ''dangerous'' (disorders in technological process; methane concentration above maximum permissible value). This approach for constructing means for gas protection is optimal only for mines working beds which are not dangerous for sudden blow-outs. However, if we ''train'' the apparatus to recognize what was the reason for increase in methane concentration, ways are afforded for solving the problem of creating an effective methane-metering equipment for mines with sudden blow-outs. Gas-dynamic processes with sudden blow-outs can be distinguished from standard technological, in particular, according to the rate in increase in methane concentration. On this basis, functional plan is proposed for constructing the automatic gas protection for explosiondangerous mines which includes a primary measurement of methane concentration, block of concentration control, block of process recognition, block of command signals, block of information delay, block of measuring the rate of methane concentration, threshold device for the rate of increase in concentration.

  12. Comparative Evaluation of Permissiveness to Dengue Virus Serotype 2 Infection in Primary Rodent Macrophages

    Directory of Open Access Journals (Sweden)

    Jeanette Prada-Arismendy

    2012-01-01

    Full Text Available Infection with dengue virus presents a broad clinical spectrum, which can range from asymptomatic cases to severe cases that are characterised by haemorrhagic syndrome and/or shock. The reason for such variability remains unknown. This work evaluated the in vitro permissiveness of mouse, rat, hamster and guinea pig macrophages to infection by dengue virus 2 (DENV2. The results established that macrophages derived from the BALB/c mouse strain showed higher permissiveness to DENV2 infection than macrophages from other rodent species, although all rodent species studied had the C820T mutation in the oligoadenylate synthetase 1b gene, indicating no relationship to the different in vitro susceptibilities of mouse cells at this locus. Other molecular mechanisms related to flavivirus susceptibility remain to be explored.

  13. Elevated lung cancer in younger adults and low concentrations of arsenic in water.

    Science.gov (United States)

    Steinmaus, Craig; Ferreccio, Catterina; Yuan, Yan; Acevedo, Johanna; González, Francisca; Perez, Liliana; Cortés, Sandra; Balmes, John R; Liaw, Jane; Smith, Allan H

    2014-12-01

    Arsenic concentrations greater than 100 µg/L in drinking water are a known cause of cancer, but the risks associated with lower concentrations are less well understood. The unusual geology and good information on past exposure found in northern Chile are key advantages for investigating the potential long-term effects of arsenic. We performed a case-control study of lung cancer from 2007 to 2010 in areas of northern Chile that had a wide range of arsenic concentrations in drinking water. Previously, we reported evidence of elevated cancer risks at arsenic concentrations greater than 100 µg/L. In the present study, we restricted analyses to the 92 cases and 288 population-based controls who were exposed to concentrations less than 100 µg/L. After adjustment for age, sex, and smoking behavior, these exposures from 40 or more years ago resulted in odds ratios for lung cancer of 1.00, 1.43 (90% confidence interval: 0.82, 2.52), and 2.01 (90% confidence interval: 1.14, 3.52) for increasing tertiles of arsenic exposure, respectively (P for trend = 0.02). Mean arsenic water concentrations in these tertiles were 6.5, 23.0, and 58.6 µg/L. For subjects younger than 65 years of age, the corresponding odds ratios were 1.00, 1.62 (90% confidence interval: 0.67, 3.90), and 3.41 (90% confidence interval: 1.51, 7.70). Adjustments for occupation, fruit and vegetable intake, and socioeconomic status had little impact on the results. These findings provide new evidence that arsenic water concentrations less than 100 µg/L are associated with higher risks of lung cancer. © The Author 2014. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  14. The study on the adaptation for regulation - the permission of a radioisotope

    Energy Technology Data Exchange (ETDEWEB)

    Park, Byoung Il; Choi, Won Seok; Jung, Yong Moon [Gallup Korea, Seoul (Korea, Republic of)

    2003-08-15

    The restriction -the permission of a radioisotope keeps satisfaction with almost parts for example, awareness, observance and so on. Moreover two concepts are considered fully -too strict about certain specific control rules and needed more discriminated application standards to each organization related to KINS, it's preserved and controlled properly even if the penalties are downsized.

  15. Activity Concentrations of radionuclides in sea water in some Coastal Egyptian Regions and Their Public Health Impacts

    International Nuclear Information System (INIS)

    Sefien, S.M.; Abdel Malik, W.E.Y.; Ibrahim, A.S.; Yousef, S.K.

    2008-01-01

    Extensive investigations have been carried out monthly for one year period in order to find out the average activity concentrations of the natural radionuclide in some Egyptian coastal aquatic environment and to assess the annual radiation doses likely to be received by population near by. The determinations were mainly for the measurement of gross α, β and γ activities in sea water samples and some of its constituents. It has been found that; the average gross α, β and γ activities in sea water samples for the different studied locations ranged from (0-52) x 10 -3 ,(3-68) x10 -3 and (13-283) x10 -3 Bq.l -1 respectively but still below the recommended permissible limits in most locations. It was found that Rashid area posses the highest concentrations of uranium and thorium. The present results have shown that the radio activities of most of the locations are mainly due to naturally occurring radionuclide. No regular tendency increase was observed in activity concentrations of any particular radionuclide in the studied period. Calculations have shown that, the average external dose from the γ- emitting radionuclide is ranged over (0.5-177)x10 -3 nGy/hr with annual exposure dose ranged from (1.04-29)x10 -3 nGy in most locations except Rashid. This exposure dose does not present radiological injuries to the population

  16. Methane on Mars: Thermodynamic Equilibrium and Photochemical Calculations

    Science.gov (United States)

    Levine, J. S.; Summers, M. E.; Ewell, M.

    2010-01-01

    The detection of methane (CH4) in the atmosphere of Mars by Mars Express and Earth-based spectroscopy is very surprising, very puzzling, and very intriguing. On Earth, about 90% of atmospheric ozone is produced by living systems. A major question concerning methane on Mars is its origin - biological or geological. Thermodynamic equilibrium calculations indicated that methane cannot be produced by atmospheric chemical/photochemical reactions. Thermodynamic equilibrium calculations for three gases, methane, ammonia (NH3) and nitrous oxide (N2O) in the Earth s atmosphere are summarized in Table 1. The calculations indicate that these three gases should not exist in the Earth s atmosphere. Yet they do, with methane, ammonia and nitrous oxide enhanced 139, 50 and 12 orders of magnitude above their calculated thermodynamic equilibrium concentration due to the impact of life! Thermodynamic equilibrium calculations have been performed for the same three gases in the atmosphere of Mars based on the assumed composition of the Mars atmosphere shown in Table 2. The calculated thermodynamic equilibrium concentrations of the same three gases in the atmosphere of Mars is shown in Table 3. Clearly, based on thermodynamic equilibrium calculations, methane should not be present in the atmosphere of Mars, but it is in concentrations approaching 30 ppbv from three distinct regions on Mars.

  17. SOIL 222Rn CONCENTRATION, CO2 AND CH4 FLUX MEASUREMENTS AROUND THE JWALAMUKHI AREA OF NORTH-WEST HIMALAYAS, INDIA.

    Science.gov (United States)

    Kumar, Arvind; Walia, Vivek; Yang, Tsanyao Frank; Fu, Ching-Chou; Singh, Surinder; Bajwa, Bikramjit Singh; Arora, Vishal

    2016-10-01

    Soil 222 Rn concentration, CO 2 and CH 4 flux measurements were conducted around the Jwalamukhi area of North-West Himalayas, India. During this study, around 37 soil gas points and flux measurements were taken with the aim to assure the suitability of this method in the study of fault zones. For this purpose, RAD 7 (Durridge, USA) was used to monitor radon concentrations, whereas portable diffuse flux meter (West Systems, Italy) was used for the CO 2 and CH 4 flux measurements. The recorded radon concentration varies from 6.1 to 34.5 kBq m -3 with an average value of 16.5 kBq m -3 The anomalous value of radon concentrations was recorded between Jwalamukhi thrust and Barsar thrust. The recorded average of CO 2 and CH 4 flux were 11.8 and 2.7 g m -2 day -1 , respectively. The good correlation between anomalous CO 2 flux and radon concentrations has been observed along the fault zone in the study area, suggesting that radon migration is dependent on CO 2 . © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  18. Gender differences in adolescent premarital sexual permissiveness in three Asian cities: effects of gender-role attitudes.

    Science.gov (United States)

    Zuo, Xiayun; Lou, Chaohua; Gao, Ersheng; Cheng, Yan; Niu, Hongfeng; Zabin, Laurie S

    2012-03-01

    Gender is an important factor in understanding premarital sexual attitudes and behaviors. Many studies indicate that males are more likely to initiate sexual intercourse and have more permissive perceptions about sex than females. Yet few studies have explored possible reasons for these gender differences. With samples of unmarried adolescents in three Asian cities influenced by Confucian cultures, this article investigates the relationship between underlying gender norms and these differences in adolescents' premarital sexual permissiveness (PSP). In a collaborative survey conducted in 2006-2007 in urban and rural areas of Hanoi, Shanghai, and Taipei, 16,554 unmarried participants aged 15-24 years were recruited in the three-City Asian Study of Adolescents and Youth, with 6,204, 6,023, and 4,327 respondents from each city, respectively. All the adolescents were administered face-to-face interviews, coupled with computer-assisted self-interview for sensitive questions. Scales on gender-role attitudes and on PSP for both male and female respondents were developed and applied to our analysis of the data. Multilinear regression was used to analyze the relationship between gender-role attitudes and sexual permissiveness. Male respondents in each city held more permissive attitudes toward premarital sex than did females, with both boys and girls expressing greater permissiveness to male premarital sexual behaviors. Boys also expressed more traditional attitudes to gender roles (condoning greater inequality) than did girls in each city. Adolescents' gender-role attitudes and permissiveness to premarital sex varied considerably across the three cities, with the Vietnamese the most traditional, the Taiwanese the least traditional, and the adolescents in Shanghai in the middle. A negative association between traditional gender roles and PSP was only found among girls in Shanghai and Taipei. In Shanghai, female respondents who held more traditional gender-role attitudes were

  19. Permissive Parenting, Deviant Peer Affiliations, and Delinquent Behavior in Adolescence: the Moderating Role of Sympathetic Nervous System Reactivity.

    Science.gov (United States)

    Hinnant, J Benjamin; Erath, Stephen A; Tu, Kelly M; El-Sheikh, Mona

    2016-08-01

    The present study examined two measures of sympathetic nervous system (SNS) activity as moderators of the indirect path from permissive parenting to deviant peer affiliations to delinquency among a community sample of adolescents. Participants included 252 adolescents (M = 15.79 years; 53 % boys; 66 % European American, 34 % African American). A multi-method design was employed to address the research questions. Two indicators of SNS reactivity, skin conductance level reactivity (SCLR) and cardiac pre-ejection period reactivity (PEPR) were examined. SNS activity was measured during a baseline period and a problem-solving task (star-tracing); reactivity was computed as the difference between the task and baseline periods. Adolescents reported on permissive parenting, deviant peer affiliations, externalizing behaviors, and substance use (alcohol, marijuana). Analyses revealed indirect effects between permissive parenting and delinquency via affiliation with deviant peers. Additionally, links between permissive parenting to affiliation with deviant peers and affiliation with deviant peers to delinquency was moderated by SNS reactivity. Less SNS reactivity (less PEPR and/or less SCLR) were risk factors for externalizing problems and alcohol use. Findings highlight the moderating role of SNS reactivity in parenting and peer pathways that may contribute to adolescent delinquency and point to possibilities of targeted interventions for vulnerable youth.

  20. 49 CFR 350.319 - What are permissible uses of High Priority Activity Funds?

    Science.gov (United States)

    2010-10-01

    ... Activity Funds? 350.319 Section 350.319 Transportation Other Regulations Relating to Transportation... permissible uses of High Priority Activity Funds? (a) The FMCSA may generally use these funds to support, enrich, or evaluate State CMV safety programs and to accomplish the five objectives listed below: (1...

  1. Legal Permissibility of Unilateral Humanitarian Interventions

    Directory of Open Access Journals (Sweden)

    Petra Perisic

    2013-03-01

    Full Text Available The paper explores the status of unilateral humanitarian interventions in international law. The United Nations Charter prohibits the use of force, except in case of self-defense and the collective action authorized by the Security Council. The question is whether the non-existence of unilateral humanitarian intervention among these exceptions means that they are not in conformity with the Charter and if so, whether the right to such interventions exists as the part of customary law. The issue has become even more controversial after the adoption of the “responsibility to protect” principle. Findings of legal scholars on this issue differ significantly. This paper analyzes and interprets the Charter provisions in order to answer the question of compatibility of humanitarian interventions with the Charter and examines the state practice in order to conclude whether the customary law rule allowing the humanitarian intervention exists. The conclusion of the paper is that there is no evidence to support the contentions that interventions without the Security Council authorization are permissible, although there are elements which point to the possibility of the creation of customary law allowing them.

  2. The SSC access shafts calculational study

    International Nuclear Information System (INIS)

    Baishev, I.S.; Mokhov, N.V.; Toohig, T.E.

    1991-06-01

    The SSC generic shaft requirements and access spacing are considered elsewhere. The shafts connecting the ground surface with the underground accelerator tunnel deliver to the surface some portion of the radiation created in the tunnel. The radiation safety problem of access shafts consists of two major questions: Does the dose equivalent at the ground surface exceed permissible limits? If it exceeds those limits, what additional shielding measures are required? A few works deal with this problem for high energy machines. This work is an attempt to answer these questions for the basic types of shafts specific to the SSC magnet delivery, utility and personnel shafts using full-scale Monte-Carlo calculations of the entire process from hadronic cascades in the lattice elements to particles scattered in the tunnel, niches, alcoves, shafts and surface bunkers and buildings. 9 refs., 16 figs., 1 tab

  3. Leishmania attachment in permissive vectors and the role of sand fly midgut proteins in parasite-vector interaction

    OpenAIRE

    Dostálová, Anna

    2012-01-01

    of PhD. thesis named "Leishmania attachment in permissive vectors and the role of sand fly midgut proteins in parasite-vector interaction", Anna Dostálová, 2011 This thesis focuses on the development of protozoan parasites of the genus Leishmania in their insect vectors, sand flies. It sums up results of three projects I was involved in during my PhD studies. Main emphasis was put on permissive sand fly species that support development of various species of Leishmania. Using a novel method of...

  4. Progress and challenges of engineering a biophysical CO2-concentrating mechanism into higher plants.

    Science.gov (United States)

    Rae, Benjamin D; Long, Benedict M; Förster, Britta; Nguyen, Nghiem D; Velanis, Christos N; Atkinson, Nicky; Hee, Wei Yih; Mukherjee, Bratati; Price, G Dean; McCormick, Alistair J

    2017-06-01

    Growth and productivity in important crop plants is limited by the inefficiencies of the C3 photosynthetic pathway. Introducing CO2-concentrating mechanisms (CCMs) into C3 plants could overcome these limitations and lead to increased yields. Many unicellular microautotrophs, such as cyanobacteria and green algae, possess highly efficient biophysical CCMs that increase CO2 concentrations around the primary carboxylase enzyme, Rubisco, to enhance CO2 assimilation rates. Algal and cyanobacterial CCMs utilize distinct molecular components, but share several functional commonalities. Here we outline the recent progress and current challenges of engineering biophysical CCMs into C3 plants. We review the predicted requirements for a functional biophysical CCM based on current knowledge of cyanobacterial and algal CCMs, the molecular engineering tools and research pipelines required to translate our theoretical knowledge into practice, and the current challenges to achieving these goals. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  5. Hamming method for solving the delayed neutron precursor concentration for reactivity calculation

    International Nuclear Information System (INIS)

    Díaz, Daniel Suescún; Ospina, Juan Felipe Flórez; Sarasty, Jesús Andrés Rodríguez

    2012-01-01

    Highlights: ► We present a new formulation to calculate the reactivity using the Hamming method. ► This method shows better accuracy than existing methods for reactivity calculation. ► The reactivity is calculated without limitation of the nuclear power form. ► The method can be implemented in reactivity meters with time step of up to 0.1 s. - Abstract: We propose a new method for numerically solving the inverse point kinetic equation for a nuclear reactor using the Hamming method, without requiring the nuclear power history and without using the Laplace transform. This new method converges with accuracy of order h 5 , where h is the step in the computation time. The procedure is validated for different forms of the nuclear power and with different time steps. The results indicate that this method has a better accuracy and lower computational effort compared with other conventional methods that use the nuclear power history.

  6. The Calculation of Self-Disposal Date by Analyzing the Radioactive Contamination of Air Filters Disused in Radioisotope Production Facility

    International Nuclear Information System (INIS)

    Kim, Sung Ho; Lee, Bu Hyung; Kwon, Soo Il

    2016-01-01

    The aim of the study is to decrease the diffusion of air contamination which occurred in radiation work places handle radioisotope under the permissible level. Accordingly, we replaced used air filter with a new one at the appropriate time , and computed disposal dates for disposing used air filters by calculate radioactive contamination. Air filter contaminated by radioactivity is possible to be self-disposed on condition that all detected nuclides is below permissible level according to Nuclear Safety and Security Commission (NSSC) notification No. 2014-003. Radioisotope, produced by 30, 50 MeV cyclotron and carried from other institutions, is used to treat patients, diagnose diseases, and research technology in Korea Institute of Radiological and Medical Sciences (KIRAMS). With unsealed sources generate radioactive contamination in air, it is important to use fume hood or hot cell. The accurate date needs to be calculated by the equation for calculation of self disposal date. If disposal date is in 1000 days, disposal for external institution is required. With increasing the number of medical institute which was related to use the radioisotopes, the importance of radioactive safety management was increased. As disposing radioactive waste, in particular, is the procedure of inspecting for releasing radioactive waste to outside, appropriate action and continuous research are required at a radioactive safety management.

  7. Calculation of tritium release from reactor's stack

    International Nuclear Information System (INIS)

    Akhadi, M.

    1996-01-01

    Method for calculation of tritium release from nuclear to environment has been discussed. Part of gas effluent contain tritium in form of HTO vapor released from reactor's stack was sampled using silica-gel. The silica-gel was put in the water to withdraw HTO vapor absorbed by silica-gel. Tritium concentration in the water was measured by liquid scintillation counter of Aloka LSC-703. Tritium concentration in the gas effluent and total release of tritium from reactor's stack during certain interval time were calculated using simple mathematic formula. This method has examined for calculation of tritium release from JRR-3M's stack of JAERI, Japan. From the calculation it was obtained the value of tritium release as much as 4.63 x 10 11 Bq during one month. (author)

  8. Calculation of near-field concentrations of hydrogen sulphide

    International Nuclear Information System (INIS)

    Baynes, C.J.

    1985-03-01

    This report provides simulations of the near-field dispersion in the atmosphere of postulated releases of hydrogen sulphide gas (H2S) at a heavy water plant. The size and extent of the flammable or detonable gas clouds which might result are estimated. This work was undertaken to support experimental studies of the detonability of H2S releases. Thirty-six different cases were simulated involving the catastrophic failure of a liquid H2S storage tank or tank car of H2S. The major variables were the size of the release, the initial mixing ratio of gas with ambient air, and the wind speed. Since the gas/air mixture is initially heavier than air, an existing heavy gas mathematical model (DENZ) was used for these simulations. The model was modified to provide the outputs needed to support the experimental studies. The outputs were the mass of H2S in the cloud, the mass and volume of the cloud, its radius at ground level and its temperature, all as functions of distance and time from release. The edge of the cloud was defined by a given concentration of H2S in air. The simulations were repeated for ten different values of this parameter, ranging between 3% and 40% H2S by volume. Simulations were also performed using a simple 'top-hat' mixing model to predict the length of the flammable or detonable jet formed at the break in a pipe carrying H2S vapour under pressure. The analysis was conducted for four postulated pipe break diameters and repeated for the same ten concentration levels used in the storage tank studies. The report presents a summary of the results. The complete outputs from the 36 storage tank failure simulations are available on floppy disks in a format suitable for detailed examination using any IBM-PC compatible microcomputer system

  9. A colorimetric sensor array for identification of toxic gases below permissible exposure limits†

    OpenAIRE

    Feng, Liang; Musto, Christopher J.; Kemling, Jonathan W.; Lim, Sung H.; Suslick, Kenneth S.

    2010-01-01

    A colorimetric sensor array has been developed for the rapid and sensitive detection of 20 toxic industrial chemicals (TICs) at their PELs (permissible exposure limits). The color changes in an array of chemically responsive nanoporous pigments provide facile identification of the TICs with an error rate below 0.7%.

  10. 26 CFR 1.414(w)-1 - Permissible withdrawals from eligible automatic contribution arrangements.

    Science.gov (United States)

    2010-04-01

    ... contribution arrangements. 1.414(w)-1 Section 1.414(w)-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT... Plans, Etc. § 1.414(w)-1 Permissible withdrawals from eligible automatic contribution arrangements. (a) Overview. Section 414(w) provides rules under which certain employees are permitted to elect to make a...

  11. THE EFFECT OF ACQUISITION ON THE STOCK RETURNS OF ACQUIRING COMPANIES: EXAMINING THE EFFECT OF ACQUISITIONS OCCURED THROUGH THE PERMISSION OF CAPITAL MARKET BOARD ON THE STOCK RETURNS OF ACQUIRING COMPANIES

    Directory of Open Access Journals (Sweden)

    LEVENT ÇITAK

    2013-06-01

    Full Text Available A merger can be defined as the economical and legal integration of two or more firms. On the other hand, an acquisiton is the transfer of all asssets and liabilities of the target firm to the acquiring firm. In the literature, merger and acquisition concepts can be used interchangeably. Firms tend to merge for the sake of creating snergy, competitive advantage, diversification, increasing firm value etc. Mergers and acquisitions are sometimes in favour of acquiring firms’ stock holders and sometimes target firms’ stock holders. Merger gains change, depending on the type of the merger and form of payment. In this study, mergers that occured through the permission of Capital Market Board have been used for the analyses. Of the mergers which have the permission, acquiring firms that are listed on Istanbul Stock Exchange have been considered and postacquisition buy and hold abnormal returns and cumulative abnormal returns have been calculated. It is concluded that postacquisition abnormal returns aren’t statistically significant. On the other hand, 1 month, 3 month, 6 month, 1 year and 2 year buy and hold abnormal returns and cumulative abnormal returns of the acquiring firms that use different payment methods are not statistically different from each other, on the basis of same return horizon. Two different methods of abnormal return calculation don’t make any difference in postacquisition abnormal returns, either.

  12. Android Application Install-time Permission Validation and Run-time Malicious Pattern Detection

    OpenAIRE

    Ma, Zhongmin

    2014-01-01

    The open source structure of Android applications introduces security vulnerabilities that can be readily exploited by third-party applications. We address certain vulnerabilities at both installation and runtime using machine learning. Effective classification techniques with neural networks can be used to verify the application categories on installation. We devise a novel application category verification methodology that involves machine learning the application permissions...

  13. Permissive hypotension in the extremely low birthweight infant with signs of good perfusion.

    LENUS (Irish Health Repository)

    Dempsey, E M

    2012-01-31

    INTRODUCTION: Many practitioners routinely treat infants whose mean arterial blood pressure in mm Hg is less than their gestational age in weeks (GA). OBJECTIVE: To assess the effectiveness of utilising a combined approach of clinical signs, metabolic acidosis and absolute blood pressure (BP) values when deciding to treat hypotension in the extremely low birthweight (ELBW) infant. METHODS: Retrospective cohort study of all live born ELBW infants admitted to our neonatal intensive care unit over a 4-year period. Patients were grouped as either normotensive (BP never less than GA), hypotensive and not treated (BPpermissive hypotension) and hypotensive treated (BPpermissive hypotension had similar outcomes. Mean blood pressure in the permissive group increased from 26 mm Hg at 6 h to 31 mm Hg at 24 h. In a logistic regression model, treated hypotension is independently associated with mortality, odds ratio 8.0 (95% CI 2.3 to 28, p<0.001). CONCLUSIONS: Blood pressure spontaneously improves in ELBW infants during the first 24 h. Infants hypotensive on GA criteria but with clinical evidence of good perfusion had as good an outcome as normotensive patients. Treated low blood pressure was associated with adverse outcome.

  14. Concentration of 134Cs and 137Cs in Malaysian palm products

    International Nuclear Information System (INIS)

    Yii Mei Wo; Nor Aza Hassan; Narizan Sanusi

    2008-08-01

    Until today, countries importing food products from Malaysia, in region such as Indian Continental, Middle East, Central Europe and Central America still require the products to be tested for the radioactive contamination particularly for 134 Cs and 137 Cs. Information extracted from 3371 analytical results observed on isotopic concentration for 134 Cs and 137 Cs in the exported Malaysia origins palm products between years 2002 until 2007 had been summarized and reported in this work. Data shown that the concentration level of the concerned radio nuclides are below the minimum detectable activity and also well below maximum permissible limits adopted by Malaysian Government and also the international bodies. (Author)

  15. Analysis of problems and failures in the measurement of soil-gas radon concentration.

    Science.gov (United States)

    Neznal, Martin; Neznal, Matěj

    2014-07-01

    Long-term experience in the field of soil-gas radon concentration measurements allows to describe and explain the most frequent causes of failures, which can appear in practice when various types of measurement methods and soil-gas sampling techniques are used. The concept of minimal sampling depth, which depends on the volume of the soil-gas sample and on the soil properties, is shown in detail. Consideration of minimal sampling depth at the time of measurement planning allows to avoid the most common mistakes. The ways how to identify influencing parameters, how to avoid a dilution of soil-gas samples by the atmospheric air, as well as how to recognise inappropriate sampling methods are discussed. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  16. Interstitial adenosine concentration is increased by dipyridamole

    International Nuclear Information System (INIS)

    Gorman, M.W.; Wangler, R.D.; DeWitt, D.F.; Wang, C.Y.; Bassingthwaighte, J.B.; Sparks, H.V.

    1986-01-01

    The authors used the multiple indicator dilution technique to observe the capillary transport of adenosine (ADO) in isolated guinea pig hearts. Radiolabelled albumin, sucrose and ADO were injected on the arterial side and measured in venous samples collected during the following 20 seconds. Transport parameters calculated from these data include permeability-surface area products (PS) for transendothelial diffusion, endothelial cell (EC) uptake at the lumenal and ablumenal membranes, and EC metabolism. With simultaneous measurements of arterial and venous ADO concentrations and flow, the authors calculated the steady-state interstitial fluid (ISF) ADO concentration. Under control conditions the venous ADO concentration was 7.1 +/- 2.8 nM. The calculated ISF concentration depends on whether they assume the venous ADO comes from the ISF, or directly from ECs. These ISF concentrations are 25 +/- 12 nM and 9.8 +/- 4.0 nM, respectively. During dipyridamole infusion (10 uM) the EC transport parameters became nearly zero. Venous and ISF ADO concentrations increased to 33 +/- 8.9 nM and 169 +/- 42 nM, respectively. The authors conclude that the ISF ADO concentration is 1.5-4 fold higher than the venous concentration at rest, and the ISF concentration increases greatly with dipyridamole

  17. Estimation of surface area concentration of workplace incidental nanoparticles based on number and mass concentrations

    Science.gov (United States)

    Park, J. Y.; Ramachandran, G.; Raynor, P. C.; Kim, S. W.

    2011-10-01

    Surface area was estimated by three different methods using number and/or mass concentrations obtained from either two or three instruments that are commonly used in the field. The estimated surface area concentrations were compared with reference surface area concentrations (SAREF) calculated from the particle size distributions obtained from a scanning mobility particle sizer and an optical particle counter (OPC). The first estimation method (SAPSD) used particle size distribution measured by a condensation particle counter (CPC) and an OPC. The second method (SAINV1) used an inversion routine based on PM1.0, PM2.5, and number concentrations to reconstruct assumed lognormal size distributions by minimizing the difference between measurements and calculated values. The third method (SAINV2) utilized a simpler inversion method that used PM1.0 and number concentrations to construct a lognormal size distribution with an assumed value of geometric standard deviation. All estimated surface area concentrations were calculated from the reconstructed size distributions. These methods were evaluated using particle measurements obtained in a restaurant, an aluminum die-casting factory, and a diesel engine laboratory. SAPSD was 0.7-1.8 times higher and SAINV1 and SAINV2 were 2.2-8 times higher than SAREF in the restaurant and diesel engine laboratory. In the die casting facility, all estimated surface area concentrations were lower than SAREF. However, the estimated surface area concentration using all three methods had qualitatively similar exposure trends and rankings to those using SAREF within a workplace. This study suggests that surface area concentration estimation based on particle size distribution (SAPSD) is a more accurate and convenient method to estimate surface area concentrations than estimation methods using inversion routines and may be feasible to use for classifying exposure groups and identifying exposure trends.

  18. Estimation of surface area concentration of workplace incidental nanoparticles based on number and mass concentrations

    International Nuclear Information System (INIS)

    Park, J. Y.; Ramachandran, G.; Raynor, P. C.; Kim, S. W.

    2011-01-01

    Surface area was estimated by three different methods using number and/or mass concentrations obtained from either two or three instruments that are commonly used in the field. The estimated surface area concentrations were compared with reference surface area concentrations (SA REF ) calculated from the particle size distributions obtained from a scanning mobility particle sizer and an optical particle counter (OPC). The first estimation method (SA PSD ) used particle size distribution measured by a condensation particle counter (CPC) and an OPC. The second method (SA INV1 ) used an inversion routine based on PM1.0, PM2.5, and number concentrations to reconstruct assumed lognormal size distributions by minimizing the difference between measurements and calculated values. The third method (SA INV2 ) utilized a simpler inversion method that used PM1.0 and number concentrations to construct a lognormal size distribution with an assumed value of geometric standard deviation. All estimated surface area concentrations were calculated from the reconstructed size distributions. These methods were evaluated using particle measurements obtained in a restaurant, an aluminum die-casting factory, and a diesel engine laboratory. SA PSD was 0.7–1.8 times higher and SA INV1 and SA INV2 were 2.2–8 times higher than SA REF in the restaurant and diesel engine laboratory. In the die casting facility, all estimated surface area concentrations were lower than SA REF . However, the estimated surface area concentration using all three methods had qualitatively similar exposure trends and rankings to those using SA REF within a workplace. This study suggests that surface area concentration estimation based on particle size distribution (SA PSD ) is a more accurate and convenient method to estimate surface area concentrations than estimation methods using inversion routines and may be feasible to use for classifying exposure groups and identifying exposure trends.

  19. Can medical students calculate drug doses? | Harries | Southern ...

    African Journals Online (AJOL)

    ... with calculations when the drug concentration was expressed either as a ratio or a percentage. Conclusion: Our findings support calls for the standardised labelling of drugs in solution and for dosage calculation training in the medical curriculum. Keywords: drug dosage calculations, clinical competence, medication errors

  20. Radionuclide concentrations in soils and produce from Cochiti, Jemez, Taos, and San Ildefonso Pueblo Gardens

    International Nuclear Information System (INIS)

    Fresquez, P.R.; Armstrong, D.R.; Salazar, J.G.

    1995-05-01

    Radionuclide ( 3 H, 90 Sr, 137 Cs, 238 Pu, 239 Pu, and total uranium) concentrations were determined in soils and produce collected from Cochiti, Jemez, Taos, and San Ildefonso Pueblo gardens. All radionuclides in soils from Pueblo areas were within or just above regional statistical (natural and/or worldwide fallout) reference levels. Similarily, the average levels of radionuclides in produce collected from Cochiti, Jemez, Taos, and San Ildefonso Pueblo gardens were not significantly different in produce collected from regional (background) locations. The effective (radiation) dose equivalent from consuming 352 lb of produce from Cochiti, Jemez, Taos, and San Ildefonso, after natural background has been subtracted, was 0.036 (±0.016), 0.072 (±0.051), 0.012 (±0.027), and 0.110 (±0.102) mrem/yr, respectively. The highest calculated dose, based on the mean + 2 std dev (95% confidence level), was 0.314 mrem/yr; this was <0.4% of the International Commission on Radiological Protection permissible dose limit for protecting members of the public

  1. Radionuclide concentrations in fish collected from Jemez, Nambe, and San Ildefonso Tribal Lakes

    International Nuclear Information System (INIS)

    Fresquez, P.R.; Armstrong, D.R.; Salazar, J.G.

    1995-02-01

    Radionuclide concentrations ( 90 Sr, 137 Cs, 238 Pu, 239 Pu,and total uranium) were determined in fish collected from Jemez, Nambe, and San Ildefonso tribal lakes. With the exception of 137 Cs, all other radionuclides were not significantly different in (stocked) rainbow trout collected from Jemez and Nambe as compared with game fish collected from Abiquiu, Heron, and El Vado Reservoirs. Although 137 Cs levels in trout from Jemez (3.2 x 10 -2 pCi per dry gram) and Nambe (7.5 x 10 -2 pCi per dry gram) were significantly higher than 137 Cs concentrations in fish from Abiquiu, Heron, and El Vado, they were still well below the regional statistical (worldwide fallout) reference level (i.e., -2 pCi per dry gram). Game and nongame fish collected from San Ildefonso contained higher and significantly higher concentrations of uranium, respectively, as compared with fish collected from Abiquiu, Heron, and El Vado. The higher uranium concentrations in fish from San Ildefonso as compared with fish from Abiquiu, Heron, and El Vado were attributed to the higher natural soil uranium contents in the area as compared with the geology of the area upstream of San Ildefonso. The effective (radiation) dose equivalent (EDE) from consuming 46 lb of game fish from Jemez, Nambe, and San Ildefonso lakes, after natural background has been subtracted, was 0.013 (±0.002), 0.019 (±0.012), and 0.017 (±0.028) mrem/yr, respectively. Similarly, the EDE from consuming nongame fish from San Ildefonso was 0.0092 (±0.0084) mrem/yr. The highest calculated dose, based on the mean + 2 standard deviation (95% confidence level), was 0.073 mrem/yr; this was <0.08% of the International Commission on Radiological Protection permissible dose limit for protecting members of the public

  2. Activation Product Inverse Calculations with NDI

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Mark Girard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-27

    NDI based forward calculations of activation product concentrations can be systematically used to infer structural element concentrations from measured activation product concentrations with an iterative algorithm. The algorithm converges exactly for the basic production-depletion chain with explicit activation product production and approximately, in the least-squares sense, for the full production-depletion chain with explicit activation product production and nosub production-depletion chain. The algorithm is suitable for automation.

  3. Permissive Attitude toward LGBT in Jakarta: Study of Differences in the Level of Permissiveness among individuals born in 1950-1970’s and 1980-2000’s

    Directory of Open Access Journals (Sweden)

    Setiowati Endang

    2017-01-01

    Full Text Available Lesbian, Gay, Bisexual and Transgender (LGBT movement is strongly resisted in Indonesia. This is not only that Indonesian people are still religious, but also the traditional norms and values are still very strong in daily life. Based on the Pew Research Centre in 2014, the homosexuality level of acceptance in Indonesia is only about 3%, while the rejection is 93%. LGBT has been started since the 1960s, but it became strength since the private television in early 1990s promoted the effeminate characters to be the top celebrities paid hundreds of millions of rupiah. People who born in the 1950s to 1970s that consume only one TV station will have different respond to LGBT with people who born in the 1980s to 2000s with some TV stations. Purpose: to look for the differences in the level of permissiveness toward homosexuality between those two groups of people. Method: using a mix method of qualitative and quantitative. Qualitative methods interviewed 6 informants. The quantitative will be a survey of 100 respondents. Result: The level of permissiveness on LGBT of the younger group is higher than the older group. According to acceptance factor both group mostly reject LGBT. But according to properness, the older group tend to say disturbing and disgusting, while for the younger group assume not disturbing.

  4. Concentration transport calculations by an original C++ program with interediate fidelity physics through user-defined buildings with an emphasis on release scenarios in radiological facilities

    Science.gov (United States)

    Sayre, George Anthony

    The purpose of this dissertation was to develop the C ++ program Emergency Dose to calculate transport of radionuclides through indoor spaces using intermediate fidelity physics that provides improved spatial heterogeneity over well-mixed models such as MELCORRTM and much lower computation times than CFD codes such as FLUENTRTM . Modified potential flow theory, which is an original formulation of potential flow theory with additions of turbulent jet and natural convection approximations, calculates spatially heterogeneous velocity fields that well-mixed models cannot predict. Other original contributions of MPFT are: (1) generation of high fidelity boundary conditions relative to well-mixed-CFD coupling methods (conflation), (2) broadening of potential flow applications to arbitrary indoor spaces previously restricted to specific applications such as exhaust hood studies, and (3) great reduction of computation time relative to CFD codes without total loss of heterogeneity. Additionally, the Lagrangian transport module, which is discussed in Sections 1.3 and 2.4, showcases an ensemble-based formulation thought to be original to interior studies. Velocity and concentration transport benchmarks against analogous formulations in COMSOLRTM produced favorable results with discrepancies resulting from the tetrahedral meshing used in COMSOLRTM outperforming the Cartesian method used by Emergency Dose. A performance comparison of the concentration transport modules against MELCORRTM showed that Emergency Dose held advantages over the well-mixed model especially in scenarios with many interior partitions and varied source positions. A performance comparison of velocity module against FLUENTRTM showed that viscous drag provided the largest error between Emergency Dose and CFD velocity calculations, but that Emergency Dose's turbulent jets well approximated the corresponding CFD jets. Overall, Emergency Dose was found to provide a viable intermediate solution method for

  5. Harmonization of standards for permissible radionuclide activity concentrations in foodstuffs in the long term after the Chernobyl accident.

    Science.gov (United States)

    Balonov, Mikhail I; Kashparov, Valery; Nikolaenko, Elena; Berkovsky, Volodymyr; Fesenko, Sergey

    2018-04-16

    The article critically examines the practice of post-Chernobyl standardization of radionuclide concentrations (mainly 137Cs and 90Sr) in food products in the USSR and the successor countries of Belarus, Russia and Ukraine. Recommendations are given on potential harmonization of these standards of radionuclide concentrations in food products among three countries, taking into account substantial international experience. We propose to reduce the number of product groups for standardization purpose from the current several dozens to three to five groups to optimize radiation control and increase the transparency of the process. We recommend five product groups for the standardization of 137Cs and three groups for 90Sr in food in radiocontaminated areas. The values of standards for individual product groups are recommended to be set proportionally to the measured specific activity in each of these groups, which will reduce unreasonable food rejection. The standards might be set for the entire country, and could be also used to control imports from other countries as well as exports to other countries. The developed recommendations were transferred in 2015-2016 to the regulatory authorities of the three countries. © 2018 IOP Publishing Ltd.

  6. Design Characteristics and Tobacco Metal Concentrations in Filtered Cigars.

    Science.gov (United States)

    Caruso, Rosalie V; O'Connor, Richard J; Travers, Mark J; Delnevo, Cristine D; Stephens, W Edryd

    2015-11-01

    While U.S. cigarette consumption has declined, cigar use has steadily increased, for reasons including price compared to cigarettes and the availability of filtered varieties resembling cigarettes, and flavors that have been banned in cigarettes (excluding menthol). Little published data exists on the design characteristics of such cigars. A variety of filtered cigar brands were tested for design characteristics such as whole cigar weight, ventilation, and per-cigar tobacco weight. Cigar sticks were then sent to the University of St. Andrews for metal concentration testing of As, Pb, Cr, Ni, and Cd. Large and small cigars were statistically different between cigar weight (p ≤ .001), per-cigar tobacco weight (p = .001), rod diameter (p = .006), and filter diameter (p = .012). The differences in mean ventilation (overall mean = 19.6%, min. = 0.84%, max. = 57.6%) across filtered cigar brands were found to be statistically significant (p = .031), and can be compared to the ventilation of the average of 2013 U.S. Marlboro Red, Gold, and Silver packs at 29% ventilation. There were no significant differences for metal concentrations between cigar types (p = .650), with Pb and As levels being similar to U.S. 2009 cigarette concentrations, Cd cigar levels being slightly higher, and Cr and Ni levels much lower than cigarette levels. With cigar use rising, and filtered cigars displaying substantial similarities to filtered cigarettes, more research on product characteristics is warranted. Future plans include testing tobacco alkaloid and more observation of cigar weight for tax bracket purposes. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  7. Importance of upper-limb inertia in calculating concentric bench press force.

    Science.gov (United States)

    Rambaud, Olivier; Rahmani, Abderrahmane; Moyen, Bernard; Bourdin, Muriel

    2008-03-01

    The purpose of this study was to investigate the influence of upper-limb inertia on the force-velocity relationship and maximal power during concentric bench press exercise. Reference peak force values (Fpeakp) measured with a force plate positioned below the bench were compared to those measured simultaneously with a kinematic device fixed on the barbell by taking (Fpeakt) or not taking (Fpeakb) upper-limb inertia into account. Thirteen men (27.8 +/- 4.1 years, 184.6 +/- 5.5 cm, 99.5 +/- 18.6 kg) performed all-out concentric bench press exercise against 8 loads ranging between 7 and 74 kg. The results showed that for each load, Fpeakb was significantly less than Fpeakp (P force (F0), maximal velocity (V0), optimal velocity (Vopt), and maximal power (Pmax), extrapolated from the force- and power-velocity relationships determined with the kinematic device, were significantly underestimated when upper-limb inertia was ignored. The results underline the importance of taking account of the total inertia of the moving system to ensure precise evaluation of upper-limb muscular characteristics in all-out concentric bench press exercise with a kinematic device. A major application of this study would be to develop precise upper-limb muscular characteristic evaluation in laboratory and field conditions by using a simple and cheap kinematic device.

  8. Recombinant pestivirus E2 glycoproteins prevent viral attachment to permissive and non permissive cells with different efficiency.

    Science.gov (United States)

    Asfor, A S; Wakeley, P R; Drew, T W; Paton, D J

    2014-08-30

    Bovine viral diarrhoea virus (BVDV) is an economically important animal pathogen, which like other pestiviruses has similar molecular biological features to hepaciviruses, including human Hepatitis C virus. The pestivirus E2 glycoproteins are the major target for virus-neutralising antibodies, as well as playing a role in receptor binding and host range restriction. In this study, recombinant E2 glycoproteins (rE2) derived from three different pestivirus species were examined for their inhibitory effects on pestivirus infectivity in cell culture. Histidine-tagged rE2 glycoproteins of BVDV type 2 strain 178003, BVDV type 1 strain Oregon C24V and CSFV strain Alfort 187 were produced in Spodoptera frugiperda insect cells and purified under native conditions. The ability of rE2 glycoprotein to inhibit the infection of permissive cells by both homologous and heterologous virus was compared, revealing that the inhibitory effects of rE2 glycoproteins correlated with the predicted similarity of the E2 structures in the recombinant protein and the test virus. This result suggests that the sequence and structure of E2 are likely to be involved in the host specificity of pestiviruses at their point of uptake into cells. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. PWR core follow calculations using the ELCOS code system

    International Nuclear Information System (INIS)

    Grimm, P.; Paratte, J.M.

    1990-01-01

    The ELCOS code system developed at PSI is used to simulate a cycle of a PWR in which one fifth of the assemblies are MOX fuel. The reactor and the calculational methods are briefly described. The calculated critical boron concentrations and power distributions are compared with the measurements at the plant. Although the critical boron concentration is somewhat overpredicted and the computed power distributions are slightly flatter than the measured ones the results of the calculations agree generally well with the measured data. (author) 1 tab., 8 figs., 6 refs

  10. Calculation of activity concentration and dose rates from online radioactivity measurement in primary coolant channel of TAPS-III and IV

    International Nuclear Information System (INIS)

    Chaudhury, Sanhita; Agarwal, Chhavi; Goswami, A.; Mhatre, Amol; Chaturvedi, T.P.; Tawde, N.; Gathibandhe, Manohar; Dash, S.C.

    2011-05-01

    Radioactivity measurement using CdZnTe detector and dose measurement using teletector were done at several locations of primary heat transport (PHT) system of the Tarapur Atomic Power Station-III and IV reactor during shut down as well as operating condition of the reactors. The detector efficiency for the required counting geometry was simulated using MCNP code. Using this simulated efficiency and the experimental count rate (cps), the activity concentrations (Bq/mL) of different radionuclides in coolant water were calculated. The dose rates for the counted locations were also simulated using Monte Carlo code and it matched well with the experimentally obtained dose rate. (author)

  11. Concentration creation of system and applied software of reactor calculations

    International Nuclear Information System (INIS)

    Zizin, M.N.

    1995-01-01

    Basic concept provisions, including modularity, openness and machine-independent programs; accumulation of procedure knowledge in form of computer module library; creation of medium facilitating module development and accompanying; possibility of head programs automated generation and user-friendly interface are presented. Intellectual program shell ShIPR for mathematical reactor modeling, the final goal whereof consists in automated generation of machine-independent programs in the Fortran 77 language on the basis of calculation moduli and accumulated knowledge base, is developed on the basis of the above concept

  12. Plasma 25-hydroxyvitamin D concentration and subsequent risk of total and site specific cancers in Japanese population: large case-cohort study within Japan Public Health Center-based Prospective Study cohort.

    Science.gov (United States)

    Budhathoki, Sanjeev; Hidaka, Akihisa; Yamaji, Taiki; Sawada, Norie; Tanaka-Mizuno, Sachiko; Kuchiba, Aya; Charvat, Hadrien; Goto, Atsushi; Kojima, Satoshi; Sudo, Natsuki; Shimazu, Taichi; Sasazuki, Shizuka; Inoue, Manami; Tsugane, Shoichiro; Iwasaki, Motoki

    2018-03-07

    To evaluate the association between pre-diagnostic circulating vitamin D concentration and the subsequent risk of overall and site specific cancer in a large cohort study. Nested case-cohort study within the Japan Public Health Center-based Prospective Study cohort. Nine public health centre areas across Japan. 3301 incident cases of cancer and 4044 randomly selected subcohort participants. Plasma concentration of 25-hydroxyvitamin D measured by enzyme immunoassay. Participants were divided into quarters based on the sex and season specific distribution of 25-hydroxyvitamin D among subcohorts. Weighted Cox proportional hazard models were used to calculate the multivariable adjusted hazard ratios for overall and site specific cancer across categories of 25-hydroxyvitamin D concentration, with the lowest quarter as the reference. Incidence of overall or site specific cancer. Plasma 25-hydroxyvitamin D concentration was inversely associated with the risk of total cancer, with multivariable adjusted hazard ratios for the second to fourth quarters compared with the lowest quarter of 0.81 (95% confidence interval 0.70 to 0.94), 0.75 (0.65 to 0.87), and 0.78 (0.67 to 0.91), respectively (P for trend=0.001). Among the findings for cancers at specific sites, an inverse association was found for liver cancer, with corresponding hazard ratios of 0.70 (0.44 to 1.13), 0.65 (0.40 to 1.06), and 0.45 (0.26 to 0.79) (P for trend=0.006). A sensitivity analysis showed that alternately removing cases of cancer at one specific site from total cancer cases did not substantially change the overall hazard ratios. In this large prospective study, higher vitamin D concentration was associated with lower risk of total cancer. These findings support the hypothesis that vitamin D has protective effects against cancers at many sites. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  13. Monte Carlo simulations used to calculate the energy deposited in the coronary artery lumen as a function of iodine concentration and photon energy.

    Science.gov (United States)

    Hocine, Nora; Meignan, Michel; Masset, Hélène

    2018-04-01

    To better understand the risks of cumulative medical X-ray investigations and the possible causal role of contrast agent on the coronary artery wall, the correlation between iodinated contrast media and the increase of energy deposited in the coronary artery lumen as a function of iodine concentration and photon energy is investigated. The calculations of energy deposition have been performed using Monte Carlo (MC) simulation codes, namely PENetration and Energy LOss of Positrons and Electrons (PENELOPE) and Monte Carlo N-Particle eXtended (MCNPX). Exposure of a cylinder phantom, artery and a metal stent (AISI 316L) to several X-ray photon beams were simulated. For the energies used in cardiac imaging the energy deposited in the coronary artery lumen increases with the quantity of iodine. Monte Carlo calculations indicate a strong dependence of the energy enhancement factor (EEF) on photon energy and iodine concentration. The maximum value of EEF is equal to 25; this factor is showed for 83 keV and for 400 mg Iodine/mL. No significant impact of the stent is observed on the absorbed dose in the artery for incident X-ray beams with mean energies of 44, 48, 52 and 55 keV. A strong correlation was shown between the increase in the concentration of iodine and the energy deposited in the coronary artery lumen for the energies used in cardiac imaging and over the energy range between 44 and 55 keV. The data provided by this study could be useful for creating new medical imaging protocols to obtain better diagnostic information with a lower level of radiation exposure.

  14. 17 CFR 240.12f-1 - Applications for permission to reinstate unlisted trading privileges.

    Science.gov (United States)

    2010-04-01

    ... reinstate unlisted trading privileges. 240.12f-1 Section 240.12f-1 Commodity and Securities Exchanges... Rules and Regulations Under the Securities Exchange Act of 1934 Unlisted Trading § 240.12f-1 Applications for permission to reinstate unlisted trading privileges. (a) An application to reinstate unlisted...

  15. 42 CFR 433.67 - Limitations on level of FFP for permissible provider-related donations.

    Science.gov (United States)

    2010-10-01

    ... provider-related donations. 433.67 Section 433.67 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES... permissible provider-related donations. (a)(1) Limitations on bona fide donations. There are no limitations on the amount of bona fide provider-related donations that a State may receive without a reduction in FFP...

  16. Maximum Permissible Risk Levels for Human Intake of Soil Contaminants: Fourth Series of Compounds

    NARCIS (Netherlands)

    Janssen PJCM; Apeldoorn ME van; Engelen JGM van; Schielen PCJI; Wouters MFA; CSR

    1998-01-01

    This report documents the human-toxicological risk assessment work done in 1996 and 1997 at RIVM's Centre for Substances and Risk Assessment within the scope of the RIVM project on soil intervention values for soil clean-up. The method used for derivation of the Maximum Permissible Risk, as

  17. EMISSION OF SOIL GAS RADON CONCENTRATION AROUND MAIN CENTRAL THRUST IN UKHIMATH (RUDRAPRAYAG) REGION OF GARHWAL HIMALAYA.

    Science.gov (United States)

    Aswal, Sunita; Kandari, Tushar; Sahoo, B K; Bourai, A A; Ramola, R C

    2016-10-01

    In this paper, the result of systematic measurement of the soil gas radon concentrations is discussed and the background values are defined along and around the Main Central Thrust (MCT) in Ukhimath region of Garhwal Himalaya, India. The Ukhimath region is being subjected to intense neotectonic activities like earthquake and landslide. For the systematic study, the measurement has been done in grid pattern form along and across the MCT. The soil gas radon concentrations were measured using RAD7 with appropriate accessories and followed proper protocol proposed by the manufacturer. The soil gas concentration was measured at different depths 10, 30 and 50 cm with a wide range of different points from the MCT. At 10 cm depth, the soil gas radon concentration was found to vary from 125 to 800 Bq m -3 with an average of 433 Bq m -3 ; at 30 cm, it was found to vary from 203 to 32 500 Bq m -3 with an average of 2387 Bq m -3 ; and at 50 cm, it was found to vary from 1330 to 46 000 Bq m -3 with an average of 15 357 Bq m -3 The data analysis clearly reveals anomalous values along the fault. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  18. X-ray radiometric analysis of lead and zinc concentrates using germanium radiation detector

    International Nuclear Information System (INIS)

    Vajgachev, A.A.; Mamysh, V.A.; Mil'chakov, V.I.; Shchekin, K.I.; Berezkin, V.V.

    1975-01-01

    The results of determination of lead, zinc and iron in lead and zinc concentrates by the X-ray-radiometric method with the use of germanium semiconductor detector are presented. In the experiments the 57 Co source and tritium-zirconium target were used. The activity of 57 Co was 2 mc. The area of the germanium detector employed was 5g mm 2 , its thickness - 2.3 mm. In lead concentrates zinc and iron were determined from the direct intensity of K-series radiation. In the analysis of zinc concentrates the same conditions of recording and excitation were used as in the case of lead concentrates, but the measurements were conducted in saturated layers. It is demonstrated that the use of germanium semiconductor detectors in combination with the suggested methods of measurements makes it possible to perform determination of iron, zinc and lead in zinc and lead concentrates with permissible error

  19. MCNP calculation of the critical H_3BO_3 concentrations for the first fuel loading into the reactor core of NPP MO-3-4 units

    International Nuclear Information System (INIS)

    Vrban, B.; Lueley, J.; Farkas, G.; Hascik, J.; Hinca, R.; Petriska, M.; Slugen, V.

    2012-01-01

    The purpose of the analysis was the determination of critical H_3BO_3 concentrations for the first fuel loading into the reactor core of MO34 units using 2"n"d generation fuel during the first start-up of new unit using calculation code MCNP 1.60. H_3BO_3 concentrations were computed for the given temperature of the primary circuit and position of the 6"t"h safety control rod group. Because of the very first start-up of these units, detailed analyses of active-core parameters are required by National Regulatory Authority and needed for safe operation of nuclear facility. (authors)

  20. Calculation method of passive tracer using regional ocean modeling system (ROMS)

    International Nuclear Information System (INIS)

    Tubono, Takaki; Tsumune, Daisuke; Misumi, Kazuhiro; Yoshida, Yoshikatsu

    2010-01-01

    A dose assessments method for packages shipping radioactive materials was developed to calculate concentrations of radioactive materials discharged from the hypothetically sinking point using Regional Ocean Modeling System (ROMS). The programs of ROMS were improved for simultaneously calculating the flow fields around Japan and the concentrations discharged from several bottom points in the continental shelf. The model domain covered the northeast pacific region around Japan, 20degN-65degN, 120degE-165degE, with 1/10 degree horizontal resolution and 30 sigma-levels. The ROMS model captured main features such as Kuroshio currents, including the separation location and the Kuroshio extension, and Oyashio currents. The calculated volume transports through the main straits such as Tokara strait, Tsushima strait and Tsugaru strait were compared well to the measured or estimated that. The calculated concentrations discharged from 12 bottom points showed mixing associated with the eddies of ocean currents. This method is available to evaluate effectively the concentrations of radioactive materials only by setting the subsidence location and the concentrations and volume discharged. (author)

  1. Prototype Centralized Managing Permissions System Based on the Election Multibiometric Authentication

    Directory of Open Access Journals (Sweden)

    Alexey Nikolaevich Ruchay

    2013-02-01

    Full Text Available This work aims to develop a prototype system of centralized managing permissions based on the election multibiometric authentication. The novelty of this work is to develop the principles of distinction and multi-factor authentication, because at the moment there is no such development. Depending on various conditions and factors, including the availability of electronic means and convenience, resistance to attacks and exploits, disease or injury of users the biometric authentication can be selected on the basis of any such biometrics as rhythm password, voice, dynamic signatures and graphics recognition.

  2. Permissive effect of dexamethasone on the increase of proenkephalin mRNA induced by depolarization of chromaffin cells

    International Nuclear Information System (INIS)

    Naranjo, J.R.; Mocchetti, I.; Schwartz, J.P.; Costa, E.

    1986-01-01

    In cultured bovine chromaffin cells, changes in the dynamic state of enkephalin stores elicited experimentally were studied by measuring cellular proenkephalin mRNA, as well as enkephalin precursors and authentic enkephalin content of cells and culture media. In parallel, tyrosine hydroxylase mRNA and catecholamine cell content were also determined. Low concentrations (0.5-100 pM) of dexamethasone increased the cell contents of proenkephalin mRNA and enkephalin-containing peptides. High concentrations of the hormone(1 μM) were required to increase the cell contents of tyrosine hydroxylase mRNA and catecholamines. Depolarization of the cells with 10 μM veratridine resulted in a depletion of enkephalin and catecholamine stores after 24 hr. The enkephalin, but not the catecholamine, content was restored by 48 hr. An increase in proenkephalin mRNA content might account for the recovery; this increase was curtailed by tetrodotoxin and enhanced by 10 pM dexamethasone. Tyrosine hydroxylase mRNA content was not significantly modified by depolarization, even in the presence of 1 μM dexamethasone. Aldosterone, progesterone, testosterone, or estradiol (1 μM) failed to change proenkephalin mRNA. Hence, dexamethasone appears to exert a specific permissive action on the stimulation of the proenkephalin gene elicited by depolarization. Though the catecholamines and enkephalins are localized in the same chromaffin granules and are coreleased by depolarization, the genes coding for the processes that are rate limiting in the production of these neuromodulators can be differentially regulated

  3. Heavy metal concentrations in the razor clams (Solen spp.) from Muara Tebas, Sarawak

    International Nuclear Information System (INIS)

    Devagi Kanakaraju; Connie Jios; Shabdin Mohd Long

    2008-01-01

    The razor clams (Solen spp) or locally known as ambal in Sarawak collected from Muara Tebas were studied for their heavy metals contents in tissues and shells. Sediment samples were also tested for their metal contents. Concentrations of Pb, Fe, Zn, Cu, Cd and Mn were determined by using Flame Atomic Absorption Spectrophotometer (FAAS). Tissues of razor clams showed highest concentrations of Fe and Zn, while shells accumulated highest concentrations of Pb and Mn. The lowest metal concentrations found were Cu and Cd. In general, the levels of metals in ambal were within the permissible limit recommended by international standard, the Food and Agricultural Organization (FAO). However, the study revealed that the sediments at Muara Tebas fall under the category of slightly polluted (for Pb) when compared to the guidelines suggested by United States Environment Protection Agency (USEPA). (author)

  4. Measurements and calculations for determination of discharge of 41Ar from IFEs research reactor JEEP II at Kjeller, Norway

    International Nuclear Information System (INIS)

    Raaum, A.; Straelberg, E.

    2003-01-01

    41 Ar is formed by neutron irradiation of 40 Ar, which occurs naturally in air with a concentration of 9300 ppm. The discharge of 41 Ar from IFEs research reactor Jeep II is yearly reported to the Norwegian Radiation Protection Authority (NRPA). Until year 2000 the reported values were based on theoretical calculations of produced 41 Ar per operating hour of 6.8 GBq/h. During 2000 and 2001 the reactor was upgraded to increase the irradiation capacity and to meet the markets demand for irradiation of 5'Si-crystalls. After the upgrading, measurements and calculations were initiated to determine the new discharge rate for 41 Ar. During reactor operation an approximately constant discharge of 41 Ar is expected, mainly due to irradiation of air in open beam channels. In addition 41 Ar is released from irradiation pockets when they are opened to transfer samples in and out during reactor stop. The new value for discharge rate was determined from measurements of air samples from the discharge channel during operation and theoretical calculations of the release from the irradiation pockets. The new discharge rate was determined to 5.9 ± 0.5 GBq/h, which is a small reduction compared to the former value of 6.8 GBq/h. A small reduction in discharge rate was expected because the number of air-filled irradiation pockets was reduced after the upgrading. In a normal year the discharge of 41 Ar will be about 2 % of the Institutes discharge permission. (orig.)

  5. Calculation of the thermal utilisation factor in a cell made up of a given number of concentric media; Calcul du facteur d'utilisation thermique dans une cellule formee d'un nombre quelconque de milieux concentriques

    Energy Technology Data Exchange (ETDEWEB)

    Amouyal, A; Benoist, P; Guionnet, Ch [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    The method of calculating the thermal utilisation factor, described in a previous report, is extended to the case of a cylindrical cell containing a given number of concentric media, certain of which may be empty. A collision by collision method is used in all but the peripheral medium, which may be treated by a theory of controlled diffusion. A programme for the IBM 650 calculator has been based on this method. Some numerical results are presented. An equivalent matrix formulation, due to C. Guionnet, is given as an appendix. (author) [French] La methode de calcul du facteur d'utilisation thermique, exposee dans un rapport precedent, est etendue au cas d'une cellule cylindrique comportant un nombre quelconque de milieux concentriques, certains de ces milieux pouvant etre vides. On utilise une methode choc par choc dans tous les milieux excepte le milieu peripherique qui peut etre traite par une theorie de diffusion ajustee. La methode a fait l'objet d'un programme pour le calculateur IBM 650. Quelques resultats numeriques sont presentes. Une formulation matricielle equivalente, due a C. Guionnet, est exposee en annexe. (auteur)

  6. A method of uranium isotopes concentration analysis

    International Nuclear Information System (INIS)

    Lin Yuangen; Jiang Meng; Wu Changli; Duan Zhanyuan; Guo Chunying

    2010-01-01

    A basic method of uranium isotopes concentration is described in this paper. The iteration method is used to calculate the relative efficiency curve, by analyzing the characteristic γ energy spectrum of 235 U, 232 U and the daughter nuclide of 238 U, then the relative activity can be calculated, at last the uranium isotopes concentration can be worked out, and the result is validated by the experimentation. (authors)

  7. Measurement of radon progeny concentrations in air by alpha-particle spectrometey

    International Nuclear Information System (INIS)

    Kerr, G.D.

    1975-07-01

    A technique is presented for measuring air concentrations of the short-lived progeny of radon-222 by the use of alpha spectrometry. In this technique, the concentration of RaA, RaB, and RaC are calculated from one integral count of the RaA and two integral counts of the RaC' alpha-particle activity collected on a filter with an air sampling device. The influence of air sampling and counting intervals of time on the accuracy of the calculated concentrations is discussed in the report. A computer program is presented for use with this technique. It is written in the BASIC language. The program will calculate the air concentrations of RaA, RaB, and RaC, and will estimate the accuracy in these calculated concentrations. (U.S.)

  8. 30 CFR 75.504 - Permissibility of new, replacement, used, reconditioned, additional, and rebuilt electric face...

    Science.gov (United States)

    2010-07-01

    ... STANDARDS-UNDERGROUND COAL MINES Electrical Equipment-General § 75.504 Permissibility of new, replacement... new, replacement, used, reconditioned, and additional electric face equipment used in any mine..., unless in the opinion of the Secretary, such equipment or necessary replacement parts are not available...

  9. 36 CFR 223.7 - Permission for free use of timber outside free-use areas.

    Science.gov (United States)

    2010-07-01

    ..., DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER General Provisions § 223.7 Permission for free use of timber outside free-use areas. Similar material may be cut outside of a free-use area without permit in cases of emergency, but the person taking such material shall promptly notify...

  10. Determination of Permissible Short-Time Emergency Overloading of Turbo-Generators and Synchronous Compensators

    Directory of Open Access Journals (Sweden)

    V. A. Anischenko

    2011-01-01

    Full Text Available The paper shows that failure to take into account variable ratio of short-time emergency overloading of turbo-generators (synchronous compensators that can lead to underestimation of overloading capacity or impermissible insulation over-heating.A method has been developed for determination of permissible duration of short-time emergency over-loading that takes into account changes of over-loading ratio in case of a failure.

  11. Seasonal and diel variation in xylem CO2 concentration and sap pH in sub-Mediterranean oak stems.

    Science.gov (United States)

    Salomón, Roberto; Valbuena-Carabaña, María; Teskey, Robert; McGuire, Mary Anne; Aubrey, Doug; González-Doncel, Inés; Gil, Luis; Rodríguez-Calcerrada, Jesús

    2016-04-01

    Since a substantial portion of respired CO2 remains within the stem, diel and seasonal trends in stem CO2 concentration ([CO2]) are of major interest in plant respiration and carbon budget research. However, continuous long-term stem [CO2] studies are scarce, and generally absent in Mediterranean climates. In this study, stem [CO2] was monitored every 15min together with stem and air temperature, sap flow, and soil water storage during a growing season in 16 stems of Quercus pyrenaica to elucidate the main drivers of stem [CO2] at different temporal scales. Fluctuations in sap pH were also assessed during two growing seasons to evaluate potential errors in estimates of the concentration of CO2 dissolved in xylem sap ([CO2*]) calculated using Henry's law. Stem temperature was the best predictor of stem [CO2] and explained more than 90% and 50% of the variability in stem [CO2] at diel and seasonal scales, respectively. Under dry conditions, soil water storage was the main driver of stem [CO2]. Likewise, the first rains after summer drought caused intense stem [CO2] pulses, suggesting enhanced stem and root respiration and increased resistance to radial CO2 diffusion. Sap flow played a secondary role in controlling stem [CO2] variations. We observed night-time sap pH acidification and progressive seasonal alkalinization. Thus, if the annual mean value of sap pH (measured at midday) was assumed to be constant, night-time sap [CO2*] was substantially overestimated (40%), and spring and autumn sap [CO2*] were misestimated by 25%. This work highlights that diel and seasonal variations in temperature, tree water availability, and sap pH substantially affect xylem [CO2] and sap [CO2*]. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  12. Present status of the physical-neutronic calculation system for nuclear fuel management at the Juragua Power Plant WWER-440 reactors

    International Nuclear Information System (INIS)

    Garcia H, Carlos R.; Milian, Daniel

    1997-01-01

    In this paper the most remarkable results obtained in Cuba, for the Juragua Nuclear Power Plant (JNPP) in core fuel management, are shown. The main characteristic of the codes used to solve the usual sequence of neutron-physical calculations available in our code library are reported. The codes validation was based on estimative of their accuracy by inter comparing calculated and WWER-440 NPP's operation data. A brief summary of the extensive calculations carried out for the JNPP Preliminary Safety Report elaboration is presented. This report is one of the requisites demanded by the Cuban Nuclear Agency for issuing the General Permission for restart works in the plant. (author). 12 refs., 4 figs., 6 tabs

  13. Hamming generalized corrector for reactivity calculation

    International Nuclear Information System (INIS)

    Suescun-Diaz, Daniel; Ibarguen-Gonzalez, Maria C.; Figueroa-Jimenez, Jorge H.

    2014-01-01

    This work presents the Hamming method generalized corrector for numerically resolving the differential equation of delayed neutron precursor concentration from the point kinetics equations for reactivity calculation, without using the nuclear power history or the Laplace transform. A study was carried out of several correctors with their respective modifiers with different time step calculations, to offer stability and greater precision. Better results are obtained for some correctors than with other existing methods. Reactivity can be calculated with precision of the order h 5 , where h is the time step. (orig.)

  14. A method to calculate equilibrium concentrations of gas and defects in the vicinity of an over-pressured bubble in UO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Noirot, L., E-mail: laurence.noirot@cea.fr

    2014-04-01

    We present a method devised to calculate the equilibrium concentration of point defects and gas atoms in the vicinity of a bubble in UO{sub 2}. First, we neglect the mechanical energy stored in the solid around an over-pressured bubble and then we explain how to take it into account. We apply the method to helium in interstitial positions in UO{sub 2}, and compare our theoretical value of Henry’s constant with experiments and a molecular dynamics computation. Then, we apply the method to xenon in a Schottky defect and use it to assess the realism of two scenarios elaborated to explain the “paradox of annealing experiments”, i.e. “why a large proportion of gas is released from grains in annealing experiments on irradiated fuel, even though there are thousands of intragranular bubbles to trap the gas?” These two scenarios (thermal resolution or blockage of trapping due to the stress field around the bubbles) were both found to be unrealistic, at least with the formation energies available from ab initio calculations, and with the assumption made to calculate the Z3 term of the partition function. This term is related to the vibration frequencies of xenon atoms in Schottky defects and lattice atoms close to defects.

  15. Access to a Loaded Gun Without Adult Permission and School-Based Bullying.

    Science.gov (United States)

    Simckes, Maayan S; Simonetti, Joseph A; Moreno, Megan A; Rivara, Frederick P; Oudekerk, Barbara A; Rowhani-Rahbar, Ali

    2017-09-01

    Gun access and bullying are risk factors for sustaining or perpetrating violence among adolescents. Our knowledge of gun access among bullied students is limited. We used data on students, aged 12-18 years, from the 2011 and 2013 School Crime Supplement to the National Crime Victimization Survey to assess the association between self-reported bullying victimization (traditional and cyber) and access to a loaded gun without adult permission. Prevalence ratios (PRs) and confidence intervals (CIs) were obtained from multivariable Poisson regression using the Taylor series after controlling for student age, sex, family income, public/private school, and race. Of 10,704 participants, 4.2% (95% CI: 3.8%-4.6%) reported gun access. Compared with nonbullied students, those who reported traditional bullying (PR = 2.2; 95% CI: 1.7-2.4), cyberbullying (PR = 2.8; 95% CI: 1.6-4.9), and both (PR = 5.9; 95% CI: 4.6-7.7) were more likely to also report gun access. Adolescents who experience bullying, particularly those who report both traditional bullying and cyberbullying, are more likely to report access to a loaded gun without adult permission. These findings highlight the importance of developing interventions focused on these modifiable risk factors for preventing self-directed or interpersonal violence among youth. Copyright © 2017 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

  16. Calculation and experimental technique of determination of rolling procedure for cold-rolling tube mills

    International Nuclear Information System (INIS)

    Igoshin, V.F.; Aleshin, V.A.; Khoroshikh, Yu.G.; Bogatov, A.A.; Mizhiritskij, O.I.

    1983-01-01

    Calculation and experimental technique of determination of tube cold rolling procedure has been developed. Rolling procedure based on the usage of regression equation epsilon=1.24 psi, where psi is the relative reduction of area, delta-permissible reduction during rolling, has been tested on 08Kh18N10T steel. The effect of tube geometry, tool calibration parameters, lubrication conditions etc. on metal deformability in taking into account experimentally. The use of the technique proposed has allowed to shorten the time of mastering of the production of tubes from different steels

  17. NASA Space Radiation Protection Strategies: Risk Assessment and Permissible Exposure Limits

    Science.gov (United States)

    Huff, J. L.; Patel, Z. S.; Simonsen, L. C.

    2017-01-01

    Permissible exposure limits (PELs) for short-term and career astronaut exposures to space radiation have been set and approved by NASA with the goal of protecting astronauts against health risks associated with ionizing radiation exposure. Short term PELs are intended to prevent clinically significant deterministic health effects, including performance decrements, which could threaten astronaut health and jeopardize mission success. Career PELs are implemented to control late occurring health effects, including a 3% risk of exposure induced death (REID) from cancer, and dose limits are used to prevent cardiovascular and central nervous system diseases. For radiation protection, meeting the cancer PEL is currently the design driver for galactic cosmic ray and solar particle event shielding, mission duration, and crew certification (e.g., 1-year ISS missions). The risk of cancer development is the largest known long-term health consequence following radiation exposure, and current estimates for long-term health risks due to cardiovascular diseases are approximately 30% to 40% of the cancer risk for exposures above an estimated threshold (Deep Space one-year and Mars missions). Large uncertainties currently exist in estimating the health risks of space radiation exposure. Improved understanding through radiobiology and physics research allows increased accuracy in risk estimation and is essential for ensuring astronaut health as well as for controlling mission costs, optimization of mission operations, vehicle design, and countermeasure assessment. We will review the Space Radiation Program Element's research strategies to increase accuracy in risk models and to inform development and validation of the permissible exposure limits.

  18. Updates to In-Line Calculation of Photolysis Rates

    Science.gov (United States)

    How photolysis rates are calculated affects ozone and aerosol concentrations predicted by the CMAQ model and the model?s run-time. The standard configuration of CMAQ uses the inline option that calculates photolysis rates by solving the radiative transfer equation for the needed ...

  19. Phebus FPT-O. Exploratory containment iodine chemistry calculations

    International Nuclear Information System (INIS)

    Fermandjian, J.; Dickinson, S.; Edward, J.B.; Ewig, F.J.; Funke, F.; Hueber, C.; Rodriguez-Maroto, J.J.; Sims, H.E.

    1994-01-01

    The results of the exploratory containment iodine chemistry calculations related to the first Phebus-FP test (benchmark exercise for explaining the reasons for code inconsistencies and realistic calculation for test preparation) are reported. Calculations have been performed by CEA/IPSN/DRS/SEMAR-Cadarache (France), CIEMAT-Madrid (Spain), GRS-Koeln and SIEMENS/KWU, Erlangen (Germany), AEA-Harwell (UK), Ontario Hydro-Toronto, University of Toronto and AECL-Whiteshell (Canada). The code benchmark results show that mechanistic codes (INSPECT and LIRIC) are in agreement for molecular iodine concentration in the gaseous phase, whereas empirical codes (IODE and IMPAIR) are in disagreement because they model differently HOI disproportionation and use different radiolytic constant values (iodide/iodate radiolysis). Furthermore, the molecular iodine concentrations in the gaseous phase are 10 to 100 times higher at acid pH (pH - 5) than at neutral pH (pH - 7), and the presence of organic radicals in water does not change the concentrations of inorganic iodine species. Concerning the realistic calculation, the iodine mass distribution in the containment differ from one code to another, but all codes predict that the iodine concentration in the gaseous phase is high enough to be detected by foreseen instrumentation (as was verified during the test). FPT-0 test has been performed in December 1993. Analysis of experimental results is underway and result interpretation will be available at the beginning of 1995. (author). 11 refs., 1 tab., 5 figs

  20. Too much of a good thing: a retrospective study of β-lactam concentration-toxicity relationships.

    Science.gov (United States)

    Imani, Sahand; Buscher, Hergen; Marriott, Debbie; Gentili, Sheridan; Sandaradura, Indy

    2017-10-01

    To determine the existence of concentration-toxicity relationships for common β-lactam antibiotic adverse effects and define thresholds above which toxicity is more likely. Retrospective review of consecutive patients treated with piperacillin, meropenem or flucloxacillin who underwent therapeutic drug monitoring (TDM) at St Vincent's Hospital (Sydney, Australia) between January 2013 and December 2015. Adverse events investigated included neurotoxicity, nephrotoxicity, hepatotoxicity and opportunistic Clostridium difficile infection. Toxicity was measured using observational grading criteria, clinical assessment and relevant serum biomarkers. These findings were correlated with trough TDM measurements at the time of toxicity presentation. TDM results from 378 patients (piperacillin = 223, meropenem = 94 and flucloxacillin = 61) were investigated. There was no difference in baseline patient characteristics across antibiotic groups. A statistically significant elevation in mean serum trough concentrations (Cmin) was found in patients diagnosed with neurotoxicity (piperacillin, P 361.4 mg/L; meropenem, Cmin >64.2 mg/L; flucloxacillin, Cmin >125.1 mg/L) or nephrotoxicity (piperacillin, Cmin >452.65 mg/L; meropenem, Cmin >44.45 mg/L) varied across antibiotics. Our data reveal an association between toxic concentrations for a number of β-lactam agents and neurotoxic/nephrotoxic effects. We have defined threshold concentrations above which these toxicities become more likely. Clinicians should balance concerns for therapeutic efficacy with potential toxicity when considering aggressive therapy. © The Author 2017. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  1. Concentration of trace metals in boreholes in the Ankobra Basin, Ghana

    International Nuclear Information System (INIS)

    Kortasi, B. K.

    2006-01-01

    Analysis of trace metals in ground water from the Ankobra basin revealed high levels of iron, manganese and aluminium. Approximately 40% of boreholes had total iron concentration exceeding 1000 μ 1 -1 (maximum WHO permissible limit). Aluminium concentration varied from 0.1 μ to 2510 μ 1 -1 with a median value of 10.0 μ 1 -1 . Approximately 20% of the boreholes had aluminium concentration exceeding the WHO maximum acceptable limit (200 μ 1 -1 ) for drinking water. Manganese concentration was in the range 6-2510 μ 1 -1 with a median of 356 μ 1 -1 . Roughly 25% of the boreholes had manganese concentrations higher that 500 μ 1 -1 , which is the WHO maximum acceptable limit for drinking water. The concentrations of mercury was higher than 1.0 μ 1 -1 (WHO maximum acceptable limit) in 60% of the boreholes during the rainy season but below detection limit in the dry season, suggesting anthropogenic origin for mercury in the groundwater. Other trace metals that occurred, but in insignificant concentration in the boreholes, include lead, arsenic, nickel and selenium. Most of the boreholes with high trace metal concentrations were located in and around the Bawdie-Bogoso-Prestea area. (au)

  2. Free Radical Oxidation in Rat Myocardium after Maximum Permissible Hepatic Resection.

    Science.gov (United States)

    Ermolaev, P A; Khramykh, T P; Barskaya, L O

    2016-03-01

    Free radical oxidation in rat myocardial homogenate was studied by chemiluminescent assay during the early terms after maximum permissible liver resection. During this period, activation of free radical oxidation was biphasic. The critical terms characterized by dramatic intensification of free radical oxidation in the myocardium are the first hour and the first day after surgery. The period from 3 to 12 h after surgery, in which the indices of chemiluminescence decrease, can be tentatively termed as the period of "putative wellbeing". Normalization of the free radical oxidation processes in the myocardium occurred by day 7 after surgery.

  3. RA-226 concentration in water samples near uranium mines and in marine fishes

    International Nuclear Information System (INIS)

    Porntepkasemsan, B.

    1987-11-01

    Radium-226 and calcium were measured in water samples from the vicinity of three uranium mines and in fish samples collected from Puget sound, Washington State. The radium content of the samples were below the maximum permissible concentration 3 pCi/L for drinking water recommended by the Public Health Service and U.S. Environmental Protection Agency. The mean value of Ra-226 in water was 0.428 pCi/L and ranged from 0.043 to 1.552 pCi/L, whereas calcium content ranged from 3.0 to 190.0 mg/L. Ra-226 concentrations and calcium content in whole fish were 0.833-20.328 pCi/kg wet wt. and 114.1-259.3 mg/g ash, respectively. Results of the study indicated that Ra-226 concentration in water was correlated with calcium concentration but that this correlation was not observed in fish sample except English sole

  4. 78 FR 52915 - Notice of Proposals to Engage In or To Acquire Companies Engaged in Permissible Nonbanking...

    Science.gov (United States)

    2013-08-27

    ... to be closely related to banking and permissible for bank holding companies. Unless otherwise noted..., Vice President) 2200 North Pearl Street, Dallas, Texas 75201-2272: 1. Rio Financial Services, Inc...

  5. CALCULATION OF AIR ION REGIME IN THE CASE OF ARTIFICIAL AIR IONIZATION

    Directory of Open Access Journals (Sweden)

    BILIAIEV M. M.

    2015-10-01

    Full Text Available Purpose. One of the major tasks in the field of labor protection is providing of the necessary qualitative composition of air in the working areas of office and industrial spaces. In order to maintain the necessary air ion level in the air space premises, the artificial ionization of air is used often in the premises. At present in Ukraine analytical model are used for the calculation of air ion regime in premises, influencing on the formation process of air ions concentration field. An alternative solution is the use of CFD models, developing including the air jets aerodynamics in the premise, the presence of furniture, equipment, transfer of ions under an electric field, and other physical factors, determining intensity and shape of air ions concentration field in the premise. Methodology. Influence of air flow was taken into account in the development of CFD models for calculation of air ion regime in the apartment, caused by operation of ventilation, diffusion, electric field impact, as well as the interaction of different polarity ions with each other, and their interaction with dust particles. The proposed model of calculation of air ion regime in premises based on the use of aerodynamics, electrostatics and mass transfer levels. This model allows operatively to calculate air ions concentration field with the influence of the walls, floor, ceiling and obstacles on the process of air ions dispersion, the specific location of different polarity ions emission and their interaction in the premise and work areas in conditions of artificial air ionization. Results. The calculated data were obtained and on their base could be estimated the concentration of air ion anywhere in the premise with artificial air ionization. Ions concentration field, being calculated using this CFD model, as concentration field isolines is presented. Originality. The results of the air ion regime calculation in the premise are presented, based on numerical 2D CFD model

  6. Requirements on waste forms for the planned Konrad repository based on criticality calculations

    International Nuclear Information System (INIS)

    Berg, H.P.

    1988-02-01

    In the framework of the safety analyses for the planned Konrad repository it has been investigated whether a criticality incident may be possible during the operational phase or in the post-operational phase. The analysis has shown that the criticality safety is ensured by limitation of a mass concentration of the fissile material in the waste form group and by determination of a maximum permissible mass of fissile material per waste package. The resulting requirements of the waste packages, including a mixture in the cross-section of an emplacement room, are explained. (orig.) [de

  7. Recommendation concerning maximum permissible radioactivity in animal feeds in case of a nuclear accident or other type of radiological emergency

    International Nuclear Information System (INIS)

    1988-01-01

    The SSK in its advice to the Federal Ministry of the Environment, Nature Conservation and Reactor Safety recommends to abstain from determining maximum permissible values to be applied in such cases of emergency. If, however, official limits are to be given, the following should be considered: (1) Distinction has to be made between animal feeds not subject to restrictive application with regard to time, animal species, or food chain (meat, milk, eggs), and those animal feeds whose application is subject to restrictions defined. (2) Maximum permissible activity data for animal feeds for restricted use should be ten times the value determined for non-restricted feeds. As to consultations within the EC on supplemtary tables to EC Directive No. 3954/87, the SSK presented its proposals in tables, using transfer factors from the literature concerning assessment of maximum permissible chronic intake of Cs-137, I-131, Sr-90, Pu-239, Am-241 by productive livestock (bovine, goats, sheep, swine, poultry). (HP) [de

  8. Shielding calculations for a 30 MeV proton accelerator

    International Nuclear Information System (INIS)

    Nandy, Maitreyee; Sarkar, P.K.

    2003-01-01

    Full text: The thickness of the shield, made of ordinary concrete, required to reduce the equivalent dose rate below the maximum permissible limit and to ensure safe operation of a 30 MeV proton accelerator has been estimated using the Moyer model. Required double differential neutron yield from thick stopping targets has been calculated for several reactions to be used for production of 67 Ga, 111 In, 123 I and 201 Tl radioisotopes. The neutron emission at 0 deg and 90 deg angles with respect to the incident beam direction is estimated using the hybrid model code ALICE91 which considers preequilibrium and equilibrium emissions from the target+projectile composite system. From this neutron yield the equivalent neutron dose rate at unit distance is determined using the ICRP recommended flux-to-dose conversion factors

  9. Calculation of concentration profiles and their experimental verification with a pulsed sieve-plate column and the reactive material system of uranyl nitrate, nitric acid/tributyl phosphate, kerosine

    International Nuclear Information System (INIS)

    Ihle, E.

    1985-01-01

    The present study is concerned with the calculation of stationary and non-stationary concentration profiles as well as with the starting and disturbance behaviour of a pulsed sieve-plate extraction column. It investigates into the material system HNO 3 /uranyl nitrate in water with 30 per cent by volume of tributyl phosphate in kerosine. During the measurements of the concentration profiles for HNO 3 transition, which were effected in the direction of extraction and reextraction, it was shown that the concentration profiles measured in the mixer-settler range, in spite of a sixfold enlargement of the specific heat transfer area, do not differ essentially from those measured in the dispersion range. During the measurements of concentration profiles for HNO 3 /uranium transition, which were effected in the direction of coextraction and co-reextraction only for mixer-settler range, it was discovered that with increasing phase ratios, there is a depletion of the uranium concentration in the aqueous phase. If the phase ratio is further raised, it is the nitric acid, and not the uranium, that is depleted. (orig./PW) [de

  10. Concentration transients in a gaseous diffusion plant (1961); Cinetique des concentrations dans une usine de separation isotopique (1961)

    Energy Technology Data Exchange (ETDEWEB)

    Jacques, R; Bilous, O [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    Concentration transients are examined in the case of a gaseous diffusion plant for uranium isotope separation. An application is made for a plant built with two rectifying cascades of different sizes and a stripping cascade. Transients are calculated for a change in the feed concentration, the transport and also for shutdown of a group of separating stages in one of the cascades. (authors) [French] On examine l'evolution des concentrations dans une usine de separation isotopique de l'uranium basee sur le procede de diffusion gazeuse et formee de cascades carrees. Une application est faite pour une installation formee de deux cascades enrichissantes de tailles differentes et d'une cascade appauvrissante. On calcule en particulier les regimes transitoires apres variation de la concentration d'alimentation, du transport et apres mise hors circuit d'un groupe d'etages dans l'une des cascades. (auteurs)

  11. Metal Concentrations of Red Wines in Southeast Romania

    Directory of Open Access Journals (Sweden)

    Florin Dumitru BORA

    2017-11-01

    Full Text Available Daily consumption, wine contributes to the requirements of essential elements, such as Ca, Fe, Mn, Mo, Co, Cr, K, Ni, Se and Zn for humans. However, the presence of significant amount of heavy metal in wine may harm the health of consumers. The present work is aimed at establishing the heavy metal content in red wines from Dealu Bujorului vineyard using ICP-MS method for the determination of metals content. In this study 3 red wines obtained from ‘Băbească neagră’, ‘Negru Aromat’ and ‘Burgund Mare’ cultivars were investigated. The wine samples were obtained from micro-wine production under conditions of 2014, 2015, 2016 from Dealu Bujorului vineyard. The determination of 13 elements was performed with ICP-MS. The high level of Ca (64.81-62.49 mg/L, Mg (132.61-101.44 mg/L and Fe were observed in the wine samples analysed. Heavy metals like As, Cd, U, Hg and Pb was found below acceptable limits. Concentration of Na (1 mg/L, Cu (1 mg/L, As (0.2 mg/L, Cd (0.01 mg/L, Zn (5 mg/L and Pb (0.15 mg/L metals in analysed wine samples were under Maximum Permissible Limits (MPL, respectively as published by the Organization of Vine and Wine. Calcium and magnesium were the most abundant elements in all investigated wine samples. Concentration of Na (1 mg/L, Cu (1 mg/L, As (0.2 mg/L, Cd (0.01 mg/L, Zn (5 mg/L and Pb (0.15 mg/L in analysed wine samples were under Maximum Permissible Limits (MPL, respectively as published by the Organization of Vine and Wine.

  12. Human T Lymphocytes Are Permissive for Dengue Virus Replication.

    Science.gov (United States)

    Silveira, Guilherme F; Wowk, Pryscilla F; Cataneo, Allan H D; Dos Santos, Paula F; Delgobo, Murilo; Stimamiglio, Marco A; Lo Sarzi, Maria; Thomazelli, Ana Paula F S; Conchon-Costa, Ivete; Pavanelli, Wander R; Antonelli, Lis R V; Báfica, André; Mansur, Daniel S; Dos Santos, Claudia N Duarte; Bordignon, Juliano

    2018-05-15

    Dengue virus (DV) infection can cause either a self-limiting flu-like disease or a threatening hemorrhage that may evolve to shock and death. A variety of cell types, such as dendritic cells, monocytes, and B cells, can be infected by DV. However, despite the role of T lymphocytes in the control of DV replication, there remains a paucity of information on possible DV-T cell interactions during the disease course. In the present study, we have demonstrated that primary human naive CD4 + and CD8 + T cells are permissive for DV infection. Importantly, both T cell subtypes support viral replication and secrete viable virus particles. DV infection triggers the activation of both CD4 + and CD8 + T lymphocytes, but preactivation of T cells reduces the susceptibility of T cells to DV infection. Interestingly, the cytotoxicity-inducing protein granzyme A is highly secreted by human CD4 + but not CD8 + T cells after exposure to DV in vitro Additionally, using annexin V and polycaspase assays, we have demonstrated that T lymphocytes, in contrast to monocytes, are resistant to DV-induced apoptosis. Strikingly, both CD4 + and CD8 + T cells were found to be infected with DV in acutely infected dengue patients. Together, these results show that T cells are permissive for DV infection in vitro and in vivo , suggesting that this cell population may be a viral reservoir during the acute phase of the disease. IMPORTANCE Infection by dengue virus (DV) causes a flu-like disease that can evolve to severe hemorrhaging and death. T lymphocytes are important cells that regulate antibody secretion by B cells and trigger the death of infected cells. However, little is known about the direct interaction between DV and T lymphocytes. Here, we show that T lymphocytes from healthy donors are susceptible to infection by DV, leading to cell activation. Additionally, T cells seem to be resistant to DV-induced apoptosis, suggesting a potential role as a viral reservoir in humans. Finally, we show

  13. Influence of the turbulence typing scheme upon the cumulative frequency distribution of the calculated relative concentrations for different averaging times

    Energy Technology Data Exchange (ETDEWEB)

    Kretzschmar, J.G.; Mertens, I.

    1984-01-01

    Over the period 1977-1979, hourly meteorological measurements at the Nuclear Energy Research Centre, Mol, Belgium and simultaneous synoptic observations at the nearby military airport of Kleine Brogel, have been compiled as input data for a bi-Gaussian dispersion model. The available information has first of all been used to determine hourly stability classes in ten widely used turbulent diffusion typing schemes. Systematic correlations between different systems were rare. Twelve different combinations of diffusion typing scheme-dispersion parameters were then used for calculating cumulative frequency distributions of 1 h, 8 h, 16 h, 3 d, and 26 d average ground-level concentrations at receptors respectively at 500 m, 1 km, 2 km, 4 km and 8 km from continuous ground-level release and an elevated release at 100 m height. Major differences were noted as well in the extreme values, the higher percentiles, as in the annual mean concentrations. These differences are almost entirely due to the differences in the numercial values (as a function of distance) of the various sets of dispersion parameters actually in use for impact assessment studies. Dispersion parameter sets giving the lowest normalized ground-level concentration values for ground level releases give the highest results for elevated releases and vice versa. While it was illustrated once again that the applicability of a given set of dispersion parameters is restricted due to the specific conditions under which the given set derived, it was also concluded that systematic experimental work to validate certain assumptions is urgently needed.

  14. Validation of analytical method to calculate the concentration of conjugated monoclonal antibody; Validacao de metodo analitico para calculo de concentracao de anticorpo monoclonal conjugado

    Energy Technology Data Exchange (ETDEWEB)

    Alcarde, Lais F.; Massicano, Adriana V.F.; Oliveira, Ricardo S.; Araujo, Elaine B. de, E-mail: lais_alcarde@hotmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    The objective of this study was to develop a quantitative analytical method using high performance liquid chromatography (HPLC) to determine the antibody concentration in conjunction with bifunctional chelator. Assays were performed using a high performance liquid chromatograph, and the following conditions were used: flow rate of 1 mL / min, 15 min run time, 0.2 M sodium phosphate buffer pH 7.0 as the mobile phase and column of molecular exclusion BioSep SEC S-3000 (300 x 7.8 mm, 5 μM - Phenomenex). The calibration curve was obtained with AcM diluted in 0.2 M sodium phosphate buffer pH 7.0 by serial dilution, yielding the concentrations: 400 μg/mL, 200 μg/mL, 100 μg/mL, 50 μg/mL, 25 μg/mL and 12.5 μg/mL. From the calibration curve calculated the equation of the line and with it the concentration of the immunoconjugate. To ensure the validity of the method accuracy and precision studies were conducted. The accuracy test consisted in the evaluation of 3 samples of known concentration, being this test performed with low concentrations (50 μg/mL), medium (100 μg/mL) and high (200 μg/mL). The precision test consisted of 3 consecutive measurements of one sample of known concentration, subject to the conditions set forth above for the other tests. The correlation coefficient of the standard curve was greater than 97%, the accuracy was satisfactory at low concentrations as well as accuracy. The method was validated by showing it for the accurate and precise determination of the concentration of the immunoconjugate. Furthermore, this assay was found to be extremely important, because using the correct mass of the protein, the radiochemical purity of the radioimmunoconjugate was above 95% in all studies.

  15. Workplace aerosol mass concentration measurement using optical particle counters.

    Science.gov (United States)

    Görner, Peter; Simon, Xavier; Bémer, Denis; Lidén, Göran

    2012-02-01

    Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM® 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO®) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions

  16. 5 CFR 890.1016 - Aggravating and mitigating factors used to determine the length of permissive debarments.

    Science.gov (United States)

    2010-01-01

    ... the debarment, or similar acts, had an adverse impact on the physical or mental health or well-being... OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE REGULATIONS (CONTINUED) FEDERAL EMPLOYEES HEALTH BENEFITS PROGRAM Administrative Sanctions Imposed Against Health Care Providers Permissive Debarments § 890...

  17. The pseudo-harmonics method applied to depletion calculation

    International Nuclear Information System (INIS)

    Silva, F.C. da; Amaral, J.A.C.; Thome, Z.D.

    1989-01-01

    In this paper, a new method for performing depletion calculations, based on the use of the Pseudo-Harmonics perturbation method, was developed. The fuel burnup was considered as a global perturbation and the multigroup difusion equations were rewriten in such a way as to treat the soluble boron concentration as the eigenvalue. By doing this, the critical boron concentration can be obtained by a perturbation method. A test of the new method was performed for a H 2 O-colled, D 2 O-moderated reactor. Comparison with direct calculation showed that this method is very accurate and efficient. (author) [pt

  18. COMPLEX OF NUMERICAL MODELS FOR COMPUTATION OF AIR ION CONCENTRATION IN PREMISES

    Directory of Open Access Journals (Sweden)

    M. M. Biliaiev

    2016-04-01

    Full Text Available Purpose. The article highlights the question about creation the complex numerical models in order to calculate the ions concentration fields in premises of various purpose and in work areas. Developed complex should take into account the main physical factors influencing the formation of the concentration field of ions, that is, aerodynamics of air jets in the room, presence of furniture, equipment, placement of ventilation holes, ventilation mode, location of ionization sources, transfer of ions under the electric field effect, other factors, determining the intensity and shape of the field of concentration of ions. In addition, complex of numerical models has to ensure conducting of the express calculation of the ions concentration in the premises, allowing quick sorting of possible variants and enabling «enlarged» evaluation of air ions concentration in the premises. Methodology. The complex numerical models to calculate air ion regime in the premises is developed. CFD numerical model is based on the use of aerodynamics, electrostatics and mass transfer equations, and takes into account the effect of air flows caused by the ventilation operation, diffusion, electric field effects, as well as the interaction of different polarities ions with each other and with the dust particles. The proposed balance model for computation of air ion regime indoors allows operative calculating the ions concentration field considering pulsed operation of the ionizer. Findings. The calculated data are received, on the basis of which one can estimate the ions concentration anywhere in the premises with artificial air ionization. An example of calculating the negative ions concentration on the basis of the CFD numerical model in the premises with reengineering transformations is given. On the basis of the developed balance model the air ions concentration in the room volume was calculated. Originality. Results of the air ion regime computation in premise, which

  19. Low concentrations of salicylic acid delay methyl jasmonate-induced leaf senescence by up-regulating nitric oxide synthase activity.

    Science.gov (United States)

    Ji, Yingbin; Liu, Jian; Xing, Da

    2016-09-01

    In plants, extensive efforts have been devoted to understanding the crosstalk between salicylic acid (SA) and jasmonic acid (JA) signaling in pathogen defenses, but this crosstalk has scarcely been addressed during senescence. In this study, the effect of SA application on methyl jasmonate (MeJA)-induced leaf senescence was assessed. We found that low concentrations of SA (1-50 μM) played a delayed role against the senescence promoted by MeJA. Furthermore, low concentrations of SA enhanced plant antioxidant defenses and restricted reactive oxygen species (ROS) accumulation in MeJA-treated leaves. When applied simultaneously with MeJA, low concentrations of SA triggered a nitric oxide (NO) burst, and the elevated NO levels were linked to the nitric oxide associated 1 (NOA1)-dependent pathway via nitric oxide synthase (NOS) activity. The ability of SA to up-regulate plant antioxidant defenses, reduce ROS accumulation, and suppress leaf senescence was lost in NO-deficient Atnoa1 plants. In a converse manner, exogenous addition of NO donors increased the plant antioxidant capacity and lowered the ROS levels in MeJA-treated leaves. Taken together, the results indicate that SA at low concentrations counteracts MeJA-induced leaf senescence through NOA1-dependent NO signaling and strengthening of the antioxidant defense. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  20. Trends and countertrends in sexual permissiveness: Three decades of attitude change in the Netherlands 1965-1995

    NARCIS (Netherlands)

    Kraaykamp, G.L.M.

    2002-01-01

    Using longitudinal data from 8 surveys on attitude change in the Netherlands, I tried to clarify trends in sexual permissiveness since the 1960s. In explaining these changes, time-period effects proved most important, whereas cohort replacement appeared to be of minor significance. Hence, changing

  1. Solubility-limited concentrations and aqueous speciation fo U, Pu, Np, Am and Tc: Comparison between results of Bruno and Sellin (1992) and calculations using GEMBOCHS (version R16)

    International Nuclear Information System (INIS)

    Bruton, C.J.

    1995-05-01

    Aqueous speciation and solubility-limited concentrations of U, Pu, Np, Am and Tc were calculated with EQ3/6 and version comR16 of the GEMBOCHS data base for comparison to similar calculations made by Bruno and Sellin (1992) for the SKB 91 exercise. Bruno and Sellin utilized data from the older 0288 version of the EQ3/6 data base but substituted their own data sets for U and Pu. Equilibria were computed in representative fresh and saline Finnsjoen-waters under oxidizing and reducing conditions. The comparisons showed that slight discrepancies exist for U because Bruno and Sellin used thermodynamic data from sources that pre-date the NEA data base. This NEA data base is incorporated into GEMBOCHS. Discrepancy also exists for Pu under reducing conditions because of the choice of thermodynamic data for solid Pu(OH) 4 . GEMBOCHS predicts Pu concentrations in solution that are about 1 to 2 orders of magnitude greater than Bruno and Sellin's values. Np concentration in the oxidizing saline water computed with GEMBOCHS is 20 times higher than Bruno and Sellin's value. Under reducing conditions, however, GEMBOCHS predicts an order of magnitude less Np in solution. GEMBOCHS computes Am concentrations in solution about 2--3-times larger than those of Bruno and Sellin. Bruno and Sellin's data base lacks the aqueous species Am(CO 3 ) 2 - although this species occurs only sparingly (< 10 mol%) in the fresh waters. Overall Tc data bases differ significantly because more recent critical compilations of Tc data have been incorporated into GEMBOCHS since Bruno and Sellin's 0288 version. Nonetheless, results for Tc are broadly similar, although GEMBOCHS predicts Tc concentrations about 1.7 times higher than Bruno and Sellin's values for the reducing waters

  2. The concentrations of uranium in marine organisms

    Energy Technology Data Exchange (ETDEWEB)

    Matsuba, Mitsue; Ishii, Toshiaki; Nakahara, Motokazu; Nakamura, Ryoichi; Watabe, Teruhisa; Hirano, Shigeki [National Inst. of Radiological Sciences, Hitachinaka, Ibaraki (Japan). Laboratory for Radioecology

    2000-07-01

    Determination of uranium in sixty-one species of marine organisms was carried out by inductively coupled plasma mass spectrometry to obtain concentration factors and to estimate the internal radiation dose. The concentrations of uranium in soft tissues of marine animals were ranged from 0.077 to 5040 ng/g wet wt. Especially, the branchial heart of cephalopod molluscs showed the specific accumulation of uranium. The concentration factor of the branchial heart of Octopus vulgaris, which indicated the highest value, was calculated to be about 1.6 x 10{sup 3}, comparing with that (3.1 ng/ml) in coastal seawaters of Japan. The concentrations of uranium in hard tissues of marine invertebrates such as clam and sea urchin were similar to those in soft tissues. In contrast, hard tissues like bone, scale, fin, etc. of fishes showed much higher concentrations of uranium than soft tissues like muscle. The concentrations of uranium of twenty-two species of algae were ranged from 2 to 310 ng/g wet wt. Particularly, the brown alga Undaria pinnatifida showed the highest value of the uranium content in the algae and its concentration factor was calculated to be 10{sup 2}. (author)

  3. The concentrations of uranium in marine organisms

    International Nuclear Information System (INIS)

    Matsuba, Mitsue; Ishii, Toshiaki; Nakahara, Motokazu; Nakamura, Ryoichi; Watabe, Teruhisa; Hirano, Shigeki

    2000-01-01

    Determination of uranium in sixty-one species of marine organisms was carried out by inductively coupled plasma mass spectrometry to obtain concentration factors and to estimate the internal radiation dose. The concentrations of uranium in soft tissues of marine animals were ranged from 0.077 to 5040 ng/g wet wt. Especially, the branchial heart of cephalopod molluscs showed the specific accumulation of uranium. The concentration factor of the branchial heart of Octopus vulgaris, which indicated the highest value, was calculated to be about 1.6 x 10 3 , comparing with that (3.1 ng/ml) in coastal seawaters of Japan. The concentrations of uranium in hard tissues of marine invertebrates such as clam and sea urchin were similar to those in soft tissues. In contrast, hard tissues like bone, scale, fin, etc. of fishes showed much higher concentrations of uranium than soft tissues like muscle. The concentrations of uranium of twenty-two species of algae were ranged from 2 to 310 ng/g wet wt. Particularly, the brown alga Undaria pinnatifida showed the highest value of the uranium content in the algae and its concentration factor was calculated to be 10 2 . (author)

  4. Application of Box-Behnken design in the optimisation of an on-line pre-concentration system using knotted reactor for cadmium determination by flame atomic absorption spectrometry

    International Nuclear Information System (INIS)

    Souza, Anderson S.; Santos, Walter N.L. dos; Ferreira, Sergio L.C.

    2005-01-01

    The present paper proposes an on-line pre-concentration system for cadmium determination in drinking water using flame atomic absorption spectrometry (FAAS). Cadmium(II) ions are retained as 1-(2-pyridylazo)-2-naphthol (PAN) complex at the walls of a knotted reactor, followed of elution using hydrochloric acid solution. The optimization was performed in two steps using factorial design for preliminary evaluation and a Box-Behnken design for determination of the critical experimental conditions. The variables involved were: sampling flow-rate, reagent concentration, pH and buffer concentration, and as response the analytical signal (absorbance). The validation process was performed considering the parameters: linearity and other characteristics of the calibration curve, analytical features of on-line pre-concentration system, precision, effect of other ions in the pre-concentration system and accuracy. Using the optimized experimental conditions, the procedure allows cadmium determination with a detection limit (3 σ / S) of 0.10 μg L -1 , a quantification limit (10 σ / S) of 0.33 μg L -1 , and a precision, calculated as relative standard deviation (RSD) of 2.7% (n = 7) and 2.4% (n = 7) for cadmium concentrations of 5 and 25 μg L -1 , respectively. A pre-concentration factor of 18 and a sampling frequency of 48 h -1 were obtained. The recovery for cadmium in the presence of several ions demonstrated that this procedure could be applied for the analysis of water samples. The method was applied for cadmium determination in drinking water samples collected in Salvador City, Brazil. The cadmium concentrations found in five samples were lower than the maximum permissible levels established by the World Health Organization

  5. Calculation of three-dimensional groundwater transport using second-order moments

    International Nuclear Information System (INIS)

    Pepper, D.W.; Stephenson, D.E.

    1987-01-01

    Groundwater transport of contaminants from the F-Area seepage basin at the Savannah River Plant (SRP) was calculated using a three-dimensional, second-order moment technique. The numerical method calculates the zero, first, and second moment distributions of concentration within a cell volume. By summing the moments over the entire solution domain, and using a Lagrangian advection scheme, concentrations are transported without numerical dispersion errors. Velocities obtained from field tests are extrapolated and interpolated to all nodal points; a variational analysis is performed over the three-dimensional velocity field to ensure mass consistency. Transport predictions are calculated out to 12,000 days. 28 refs., 9 figs

  6. Psychometric Support for a New Measure of Authoritative, Authoritarian, and Permissive Parenting Practices: Cross-Cultural Connections.

    Science.gov (United States)

    Robinson, Clyde C.; And Others

    This study examined the psychometric characteristics of a 62-item parenting questionnaire completed by parents from the United States, Australia, China, and Russia. Factor analyses yielded three global parenting dimensions for each culture which were consistent with D. Baumrind's (1971) authoritative, authoritarian, and permissive typologies. The…

  7. Guidance document on the derivation of maximum permissible risk levels for human intake of soil contaminants

    NARCIS (Netherlands)

    Janssen PJCM; Speijers GJA; CSR

    1997-01-01

    This report contains a basic step-to-step description of the procedure followed in the derivation of the human-toxicological Maximum Permissible Risk (MPR ; in Dutch: Maximum Toelaatbaar Risico, MTR) for soil contaminants. In recent years this method has been applied for a large number of compounds

  8. 34 CFR 97.408 - Requirements for permission by parents or guardians and for assent by children.

    Science.gov (United States)

    2010-07-01

    ... permission is not a reasonable requirement to protect the subjects (for example, neglected or abused children... for assent by children. 97.408 Section 97.408 Education Office of the Secretary, Department of Education PROTECTION OF HUMAN SUBJECTS Additional ED Protections for Children Who Are Subjects in Research...

  9. 26 CFR 301.7216-2T - Permissible disclosures or uses without consent of the taxpayer (temporary).

    Science.gov (United States)

    2010-04-01

    ... return preparer has prepared or processed. The Internal Revenue Service may issue guidance, by... auditing services. A quality or peer review may be conducted only by attorneys, certified public... 26 Internal Revenue 18 2010-04-01 2010-04-01 false Permissible disclosures or uses without consent...

  10. Health impact of supplying safe drinking water containing fluoride below permissible level on flourosis patients in a fluoride-endemic rural area of West Bengal.

    Science.gov (United States)

    Majumdar, Kunal Kanti

    2011-01-01

    The problem of high fluoride concentration in groundwater resources has become one of the most important toxicological and geo-environmental issues in India. Excessive fluoride in drinking water causes dental and skeletal fluorosis, which is encountered in endemic proportions in several parts of the world. World Health Organization (WHO) guideline value and the permissible limit of fluoride as per Bureau of Indian Standard (BIS) is 1.5 mg/L. About 20 states of India, including 43 blocks of seven districts of West Bengal, were identified as endemic for fluorosis and about 66 million people in these regions are at risk of fluoride contamination. Studies showed that withdrawal of sources identified for fluoride often leads reduction of fluoride in the body fluids (re-testing urine and serum after a week or 10 days) and results in the disappearance of non-skeletal fluorosis within a short duration of 10-15 days. To determine the prevalence of signs and symptoms of suspected dental, skeletal, and non-skeletal fluorosis, along with food habits, addictions, and use of fluoride containing toothpaste among participants taking water with fluoride concentration above the permissible limit, and to assess the changes in clinical manifestations of the above participants after they started consuming safe drinking water. A longitudinal intervention study was conducted in three villages in Rampurhat Block I of Birbhum district of West Bengal to assess the occurrence of various dental, skeletal, and non-skeletal manifestations of fluorosis, along with food habits, addictions, and use of fluoride containing toothpaste among the study population and the impact of taking safe water from the supplied domestic and community filters on these clinical manifestations. The impact was studied by follow-up examination of the participants for 5 months to determine the changes in clinical manifestations of the above participants after they started consuming safe drinking water from supplied

  11. Inventory model with cash flow oriented and time-dependent holding cost under permissible delay in payments

    Directory of Open Access Journals (Sweden)

    Tripathi R.P.

    2013-01-01

    Full Text Available This study develops an inventory model for determining an optimal ordering policy for non-deteriorating items and time-dependent holding cost with delayed payments permitted by the supplier under inflation and time-discounting. The discounted cash flows approach is applied to study the problem analysis. Mathematical models have been derived under two different situations i.e. case I: The permissible delay period is less than cycle time for settling the account and case II: The permissible delay period is greater than or equal to cycle time for settling the account. An algorithm is used to obtain minimum total present value of the costs over the time horizon H. Finally, numerical example and sensitivity analysis demonstrate the applicability of the proposed model. The main purpose of this paper is to investigate the optimal cycle time and optimal payment time for an item so that annual total relevant cost is minimized.

  12. Calculation of neutron kerma in tissues

    International Nuclear Information System (INIS)

    Vega C, H.R.; Manzanares A, E.

    2004-01-01

    Neutron kerma of normal and tumor tissues has been calculated using the tissues elemental concentration. A program developed in Math cad contains the kerma factors of C, H, O, N, Na, Mg, P, S, Cl, K, etc. that are in normal and tumor human tissues. Having the elemental composition of any human tissue the neutron kerma can be calculated. The program was tested using the elemental composition of tumor tissues such as sarcoma, melanoma, carcinoma and adenoid cystic, also neutron kerma for adipose and muscle tissue for normal adult was calculated. The results are in agreement with those published in literature. The neutron kerma for water was also calculated because in some dosimetric calculations water is used to describe normal and tumor tissues. From this comparison was found that at larger energies kerma factors are approximately the same, but energies less than 100 eV the differences are large. (Author)

  13. Retailer’s replenishment policies under conditions of permissible delay in payments

    Directory of Open Access Journals (Sweden)

    Huang Yung-Fu

    2004-01-01

    Full Text Available Goyal (1985 is frequently cited when the inventory systems under conditions of permissible delay in payments are discussed. Goyal implicitly assumed that: 1. The unit selling price and the unit purchasing price are equal; 2. At the end of the credit period, the account is settled. The retailer starts paying for higher interest charges on the items in stock and returns money of the remaining balance immediately when the items are sold. But these assumptions are debatable in real-life situations. The main purpose of this paper is to modify Goyal’s model to allow the unit selling price and the unit purchasing price not necessarily be equal to reflect the real-life situations. Furthermore, this paper will adopt different payment rule. We assume that the retailer uses sales revenue during the permissible credit period to make payment to the supplier at the end of the credit period. If it is not enough to pay off the purchasing cost of all items, the retailer will pay off the remaining balance by taking loan from the bank. So, the retailer starts paying for the interest charges on the amount of loan from the bank after the account is settled. Then the retailer will return money to the bank at the end of the inventory cycle. Under these conditions, we model the retailer’s inventory system as a cost minimization problem to determine the retailer’s optimal cycle time and optimal order quantity. Four cases are developed to efficiently determine the optimal cycle time and the optimal order quantity. Numerical examples are given to illustrate these cases. Comparing with Goyal’s model, we also find that the optimal cycle times in this paper are not longer than those of Goyal’s model.

  14. Labview virtual instruments for calcium buffer calculations.

    Science.gov (United States)

    Reitz, Frederick B; Pollack, Gerald H

    2003-01-01

    Labview VIs based upon the calculator programs of Fabiato and Fabiato (J. Physiol. Paris 75 (1979) 463) are presented. The VIs comprise the necessary computations for the accurate preparation of multiple-metal buffers, for the back-calculation of buffer composition given known free metal concentrations and stability constants used, for the determination of free concentrations from a given buffer composition, and for the determination of apparent stability constants from absolute constants. As implemented, the VIs can concurrently account for up to three divalent metals, two monovalent metals and four ligands thereof, and the modular design of the VIs facilitates further extension of their capacity. As Labview VIs are inherently graphical, these VIs may serve as useful templates for those wishing to adapt this software to other platforms.

  15. Measured density and calculated baricity of custom-compounded drugs for chronic intrathecal infusion.

    Science.gov (United States)

    Hejtmanek, Michael R; Harvey, Tracy D; Bernards, Christopher M

    2011-01-01

    To minimize the frequency that intrathecal pumps require refilling, drugs are custom compounded at very high concentrations. Unfortunately, the baricity of these custom solutions is unknown, which is problematic, given baricity's importance in determining the spread of intrathecally administered drugs. Consequently, we measured the density and calculated the baricity of clinically relevant concentrations of multiple drugs used for intrathecal infusion. Morphine, clonidine, bupivacaine, and baclofen were weighed to within 0.0001 g and diluted in volumetric flasks to produce solutions of known concentrations (morphine 1, 10, 25, and 50 mg/mL; clonidine 0.05, 0.5, 1, and 3 mg/mL; bupivacaine 2.5, 5, 10, and 20 mg/mL; baclofen 1, 1.5, 2, and 4 mg/mL). The densities of the solutions were measured at 37°C using the mechanical oscillation method. A "best-fit" curve was calculated for plots of concentration versus density for each drug. All prepared solutions of clonidine and baclofen were hypobaric. Higher concentrations of morphine and bupivacaine were hyperbaric, whereas lower concentrations were hypobaric. The relationship between concentration and density is linear for morphine (r > 0.99) and bupivacaine (r > 0.99) and logarithmic for baclofen (r = 0.96) and clonidine (r = 0.98). This is the first study to examine the relationship between concentration and density for custom drug concentrations commonly used in implanted intrathecal pumps. We calculated an equation that defines the relationship between concentration and density for each drug. Using these equations, clinicians can calculate the density of any solution made from the drugs studied here.

  16. 12 CFR 347.115 - Permissible activities for a foreign branch of an insured state nonmember bank.

    Science.gov (United States)

    2010-01-01

    ... political subdivisions, to the extent permissible under the law of the issuing foreign country; and (ii) An... under the law of the issuing foreign country, if supported by the taxing authority, guarantee, or full... securities eligible to meet local reserve or similar requirements; and (iii) Shares of automated electronic...

  17. Nondestructive measurement for radionuclide concentration distribution in soil column

    International Nuclear Information System (INIS)

    Ogawa, Hiromichi; Ohnuki, Toshihiko; Yamamoto, Tadatoshi; Wadachi, Yoshiki

    1985-01-01

    A nondestructive method has been studied for determining the concentration of radionuclide (Cs-137) distributed in a soil column. The concentration distribution was calculated from the counting rate distribution using the efficiency matrix of a detector. The concentration distribution obtained by this method, with measuring efficiencies of theoretical calculation, coincides well with that obtained by the destructive sampling method. This method is, therefore, found to be effective for the measurement of one dimensional concentration distribution. The measuring limit of this method is affected not only by the radionuclide concentration but also by the shape of concentration distribution in a soil column and also by the way it is divided into concentration blocks. It is found that, the radioactive concentration up to 2.6 x 10 -4 μCi/g (9.62 Bq/g), and also the distribution up to where the concentration reduces to half at every 1 cm of depth, can be measured by this system. The concentration blocks can be divided into 1 cm of thickness as a minimum value. (author)

  18. Studies on the establishment of maximum permissible exposure dose for reference Korean

    International Nuclear Information System (INIS)

    Kim, Y.J.; Lee, K.S.; Chun, K.C.; Kim, C.B.; Chung, K.H.; Kim, S.L.; Kim, M.J.

    1981-01-01

    In order to establish the Reference Korean and maximum permissible exposure dose of Reference Korean, for the first year a total of 9,758 males and 7,019 females were surveyed for the height, weight, a body surface area, and a total of 879 individuals of 180 households located in different 30 localities were analyzed for food consumption and a total of radioactive substances (β-ray) contained in food per capita per day. In this report the external and internal exposure dose were also estimated on the basis of data mostly published in other country as well as in Korea in part

  19. Analyzing silver concentration in soil using laser-induced breakdown spectroscopy

    Science.gov (United States)

    Prasetyo, S.; Isnaeni; Zaitun; Mitchell, K.; Suliyanti, M. M.; Herbani, Y.

    2018-03-01

    Determination of concentration of heavy metal ions in soil, such as silver, is very important to study soil pollution levels. Several techniques have been developed to determine silver ion concentration in soil. In this paper, we utilized laser-induced breakdown spectroscopy (LIBS) to study silver concentration in soil. We used four different data analysis methods to calculate silver concentration. In this case, we prepared soil samples with different silver ion concentrations from 400 ppm to 1000 ppm. Our analysis was focused on the 843.15 nm silver atomic absorption line. We found that plasma intensity increased as silver concentration increased. Our findings were based on our analysis using four different analysis methods. We believe that these analysis methods are able to calculate silver concentration in soil using LIBS.

  20. Parallel computational in nuclear group constant calculation

    International Nuclear Information System (INIS)

    Su'ud, Zaki; Rustandi, Yaddi K.; Kurniadi, Rizal

    2002-01-01

    In this paper parallel computational method in nuclear group constant calculation using collision probability method will be discuss. The main focus is on the calculation of collision matrix which need large amount of computational time. The geometry treated here is concentric cylinder. The calculation of collision probability matrix is carried out using semi analytic method using Beckley Naylor Function. To accelerate computation speed some computer parallel used to solve the problem. We used LINUX based parallelization using PVM software with C or fortran language. While in windows based we used socket programming using DELPHI or C builder. The calculation results shows the important of optimal weight for each processor in case there area many type of processor speed

  1. Relationship between haemoglobin concentration and packed cell volume in cattle blood samples

    Directory of Open Access Journals (Sweden)

    Paa-Kobina Turkson

    2015-02-01

    Full Text Available A convention that has been adopted in medicine is to estimate haemoglobin (HB concentration as a third of packed cell volume (PCV or vice versa. The present research set out to determine whether a proportional relationship exists between PCV and Hb concentration in cattle blood samples, and to assess the validity of the convention of estimating Hb concentration as a third of PCV. A total of 440 cattle in Ghana from four breeds (Ndama, 110; West African Short Horn, 110; Zebu, 110 and Sanga, 110 were bled for haematological analysis, specifically packed cell volume, using the microhaematocrit technique and haemoglobin concentration using the cyanmethaemoglobin method. Means, standard deviations, standard errors of mean and 95% confidence intervals were calculated. Trendline analyses generated linear regression equations from scatterplots. For all the cattle, a significant and consistent relationship (r = 0.74 was found between Hb concentration and PCV (%. This was expressed as Hb concentration (g/dL = 0.28 PCV + 3.11. When the Hb concentration was estimated by calculating it as a third of PCV, the relationship was expressed in linear regression as Hb concentration (g/dL = 0.83 calculated Hb + 3.11. The difference in the means of determined (12.2 g/dL and calculated (10.9 g/dL Hb concentrations for all cattle was significant (p < 0.001, whereas the difference in the means of determined Hb and corrected calculated Hb was not significant. In conclusion, a simplified relationship of Hb (g/dL = (0.3 PCV + 3 may provide a better estimate of Hb concentration from the PCV of cattle.

  2. Investigation of Pb, Cd, Cu and Mg Concentrations in Groundwater Resources of Razan Plain

    Directory of Open Access Journals (Sweden)

    S. Sobhan Ardakani

    2015-01-01

    Full Text Available Introduction & Objective: Iran is located in the dry and semi dry regions, thus almost 90% of the required fresh water is exploited from groundwater resources. Due to the increasing pol-lution of water resources, the purpose of this study was evaluation of Pb, Cd, Cu and Mg concentrations in groundwater resources of Razan Plain and preparing the zoning map using GIS. Materials & Methods: Groundwater samples were collected from 20 selected stations during two seasons in 2012. The samples were filtered (0.45 ?m and maintained cool in polyethyl-ene bottles. The samples were taken for the analysis of cations, the former was acidified with HNO3 to pH lower than 2. Minor elements were determined using ICP-OES. All statistical analyses were performed using the SPSS statistical package. Also, Kriging Method was used to prepare spatial distribution maps of elements in groundwater samples. Results: The results showed that the mean concentrations of Pb, Cd, Cu and Mg in the groundwater samples during the spring were 5.60±0.66, 0.21±0.04, 32.10±2.21 and 6990.0±302.10 ppb, respectively, and the mean concentrations of these elements in the groundwater samples in the summer were 4.86±0.46, 0.30±0.08, 25.55±3.63 and 3654.05±215.65 ppb, respectively. Comparing the mean concentrations of the evaluated metals with WHO permissible limits showed a significant difference (p<0.05. Thus, the mean concentrations of the metals were significantly lower than the permissible limits. Conclusion: Although the groundwater resources of Razan Plain are not currently polluted with heavy metals, long-term excessive use of agricultural inputs and establishment of pollut-ing industries, can pose a threat to groundwater resources of this area. (Sci J Hamadan Univ Med Sci 2015; 21(4:319-329

  3. Recalculation of measured fuel nuclide concentrations

    International Nuclear Information System (INIS)

    Moeller, W.

    1984-01-01

    The concentrations and concentration ratios of heavy fuel nuclides determined in the Central Institute for Nuclear Research Rossendorf on the basis of destructive burnup measurements are compared with the results of microburnup calculations. The possibility is discussed to improve the results by taking into account the spectral characteristics at the positions of the measuring samples. (author)

  4. Acute 5-(2-aminopropyl)benzofuran (5-APB) intoxication and fatality: a case report with postmortem concentrations.

    Science.gov (United States)

    McIntyre, Iain M; Gary, Ray D; Trochta, Amber; Stolberg, Susan; Stabley, Robert

    2015-03-01

    A 20-year-old man, a college student, became unresponsive in front of his girlfriend. He was known to consume alcohol and take an unknown drug at some point while in attendance at a local music festival earlier in the day/evening. Upon arrival of emergency personnel, he was noted to be asystolic and apneic. Despite aggressive medical intervention by emergency personnel and at a local hospital emergency room, he was pronounced deceased within 1.25 h of initial medical attention. Postmortem blood initially screened positive for methamphetamine by ELISA. An alkaline drug screen detected 5-(2-aminopropyl)benzofuran (5-APB) which was subsequently confirmed and quantified by a specific GC-MS SIM analysis following solid-phase extraction. Concentrations were determined in the peripheral blood (2.5 mg/L), central blood (2.9 mg/L), liver (16 mg/kg), vitreous (1.3 mg/L), urine (23 mg/L) and gastric contents (6 mg). No other common amphetamine-like compound was detected, although 5-(2-aminopropyl)-2,3-dihydrobenzofuran (5-APDB) was presumptively identified in both peripheral blood and urine. Alcohol, the only other drug identified, was confirmed at a concentration of 0.02% (w/v). © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Determination of hazardous ingredients in personal care products using laser-induced breakdown spectroscopy

    Science.gov (United States)

    Abrar, M.; Iqbal, T.; Fahad, M.; Andleeb, M.; Farooq, Z.; Afsheen, S.

    2018-05-01

    In the present work, the laser-induced breakdown spectroscopy technique is applied to explore the concentration of toxic elements present in cosmetic materials. The elemental analysis of chromium (Cr), magnesium (Mg), cadmium (Cd) and lead (Pb) are selected as major elements and manganese (Mn), sodium (Na), potassium (P), sulfur (S), silicon (Si) and titanium (Ti) as minor elements in cosmetic products. In this technique, a plasma plume is generated by using an Nd:YAG Laser of 532 nm wavelength and spectral lines for the respective samples are observed. Four different samples of cosmetic products are selected, i.e. two samples for lipstick and two for eyeshadow. The observed spectral lines of all major and minor elements are used to calculate their concentration in all samples through the intensity ratio method. Among selected lipstick and eyeshadow samples, one sample is branded, and one is collected from the local market. It is observed that chromium, magnesium and lead have strong spectral lines and consequently show high concentration. The calculated concentrations are then compared to permissible limits set by the Food and Drug Administration with regard to the cosmetics industry. The concentration of these toxic elements in selected local cosmetic samples exceeds the safe permissible limit for human use and could lead to serious health problems.

  6. A Static Android Malware Detection Based on Actual Used Permissions Combination and API Calls

    OpenAIRE

    Xiaoqing Wang; Junfeng Wang; Xiaolan Zhu

    2016-01-01

    Android operating system has been recognized by most application developers because of its good open-source and compatibility, which enriches the categories of applications greatly. However, it has become the target of malware attackers due to the lack of strict security supervision mechanisms, which leads to the rapid growth of malware, thus bringing serious safety hazards to users. Therefore, it is critical to detect Android malware effectively. Generally, the permissions declared in the An...

  7. Limestone-Concentrate-Pellet Roasting in wet Carbon Dioxide

    Institute of Scientific and Technical Information of China (English)

    1990-01-01

    A roast process for treating chalcopyrite concentrate was developed. The investigation of the reaction of limestone-concentrate-pellet in a wet carbon dioxide flow was carried out by means of a thermogravimetric analysis (TGA) to determine at which temperatures the roasting reaction would take place. The thermodynamic calculations on the roast reaction were made by the use of SOLGASMIX-PV program. The TGA curves and thermodynamic calculations indicated that the conversion of chalcopyrite into bornite took place at about 975K, and the conversion of bornite into chalcocite at 1065-1123K. The thermodynamic calculations also showed that the sulfur released was fixed as calcium sulfide within roasted pellets. X-ray diffraction examination identified these phases in products.

  8. Application of ICRP recommendations relevant to internal dose

    International Nuclear Information System (INIS)

    Cowser, K.E.; Snyder, W.S.; Struxness, E.G.

    1969-01-01

    The intent of this paper is to review several of the basic concepts of radiation protection (with emphasis on internal dose) currently recommended by the International Commission on radiological Protection (ICRP), to summarize the assumptions and methods used in the calculation of internal dose, and to illustrate by example the practical application of the pertinent guidelines. Two broad subject areas are considered: (1) standards of radiation protection and (2) bases of internal dose estimation. Topics discussed within the framework of radiation protection standards include maximum permissible dose, categories of radiation exposure, maximum permissible dose commitment, simultaneous internal and external exposure, multiple organ exposure, and size of the exposed group. Discussion of internal dose estimation is limited to selected items that include the body burden of radionuclides and the calculation of absorbed dose, the dose equivalent, the derivation of maximum permissible concentration (MPC), the relationship of stable element intake to the MPC, and short term and chronic exposure situations. (author)

  9. Application of ICRP recommendations relevant to internal dose

    Energy Technology Data Exchange (ETDEWEB)

    Cowser, K E; Snyder, W S; Struxness, E G [Health Physics Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

    1969-07-01

    The intent of this paper is to review several of the basic concepts of radiation protection (with emphasis on internal dose) currently recommended by the International Commission on radiological Protection (ICRP), to summarize the assumptions and methods used in the calculation of internal dose, and to illustrate by example the practical application of the pertinent guidelines. Two broad subject areas are considered: (1) standards of radiation protection and (2) bases of internal dose estimation. Topics discussed within the framework of radiation protection standards include maximum permissible dose, categories of radiation exposure, maximum permissible dose commitment, simultaneous internal and external exposure, multiple organ exposure, and size of the exposed group. Discussion of internal dose estimation is limited to selected items that include the body burden of radionuclides and the calculation of absorbed dose, the dose equivalent, the derivation of maximum permissible concentration (MPC), the relationship of stable element intake to the MPC, and short term and chronic exposure situations. (author)

  10. The mothering of conduct problem and normal children in Spain and the USA: authoritarian and permissive asynchrony.

    Science.gov (United States)

    Wahler, Robert G; Cerezo, M Angeles

    2005-11-01

    Ninety-two clinic-referred and nonclinical mother-child dyads in Spain and the USA were observed in their home settings under naturalistic conditions for a total of 477 hours. Children in the clinic-referred dyads were considered troubled because of conduct problems. The observations were aimed at assessing two forms of mother-child asynchrony, either of which was expected to differentiate clinic referred from nonclinical dyads. Authoritarian asynchrony was defined as a mother's indiscriminate use of aversive reactions to her child, whereas the permissive form entailed indiscriminate positive reactions. Results showed the American mothers to generate more permissive asynchrony, whereas the Spanish mothers were inclined in the authoritarian direction. Only authoritarian asynchrony differentiated the clinical versus nonclinical dyads in each country. Discussion was centered on the greater salience of aversive as opposed to positive maternal attention, and cultural differences between countries that might have accounted for the different parenting styles.

  11. Neutronic calculations for Angra-1 steam line break accident

    International Nuclear Information System (INIS)

    Ponzoni Filho, Pedro; Sato, Sadakatu

    2000-01-01

    The reduction of boron concentration in the Boron Injection Tank (BIT), to the room temperature solubility level, makes necessary a reanalysis of the steam line break accident of Angra 1 NPP. This paper describes the neutronic calculation related to this reanalysis. The main steps of the work were: review of reactivity parameters used in the accident simulation; search of xenon profiles that cause the most severe core power distribution; calculation of hot channel factors and other neutronic parameters necessary for DNBR determination. The final conclusion, related to the steam line break accident, states the BIT concentration may be reduced to 2000 ppm. (author)

  12. ESTABLISHMENT OF DETAILED EYE MODEL OF ADULT CHINESE MALE AND DOSE CONVERSION COEFFICIENTS CALCULATION UNDER NEUTRON EXPOSURE.

    Science.gov (United States)

    Zhu, Hongyu; Qiu, Rui; Wu, Zhen; Ren, Li; Li, Chunyan; Zhang, Hui; Li, Junli

    2017-12-01

    The human eye lens is sensitive to radiation. ICRP-118 publication recommended a reduction of the occupational annual equivalent dose limit from 150 to 20 mSv, averaged over defined periods of 5 y. Therefore, it is very important to build a detailed eye model for the accurate dose assessment and radiation risk evaluation of eye lens. In this work, a detailed eye model was build based on the characteristic anatomic parameters of the Chinese adult male. This eye model includes seven main structures, which are scleral, choroid, lens, iris, cornea, vitreous body and aqueous humor. The lens was divided into sensitive volume and insensitive volume based on different cell populations. The detailed eye model was incorporated into the converted polygon-mesh version of the Chinese reference adult male whole-body surface model. After the incorporation, dose conversion coefficients for the eye lens were calculated for neutron exposure at AP, PA and LAT geometries with Geant4, the neutron energies were from 0.001 eV to 10 MeV. The calculated lens dose coefficients were compared with those of ICRP-116 publication. Significant differences up to 97.47% were found at PA geometry. This could mainly be attributed to the different geometry characteristic of eye model and parameters of head in different phantom between the present work and ICRP-116 publication. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. Concentration and size distribution of particles in abstracted groundwater

    NARCIS (Netherlands)

    Van Beek, C.G.E.M.; de Zwart, A.H.; Balemans, M.; Kooiman, J.W.; van Rosmalen, C.; Timmer, H.; Vandersluys, J.; Stuijfzand, P.J.

    2010-01-01

    Particle number concentrations have been counted and particle size distributions calculated in groundwater derived by abstraction wells. Both concentration and size distribution are governed by the discharge rate: the higher this rate the higher the concentration and the higher the proportion of

  14. A nonparametric approach to calculate critical micelle concentrations: the local polynomial regression method

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Fontan, J.L.; Costa, J.; Ruso, J.M.; Prieto, G. [Dept. of Applied Physics, Univ. of Santiago de Compostela, Santiago de Compostela (Spain); Sarmiento, F. [Dept. of Mathematics, Faculty of Informatics, Univ. of A Coruna, A Coruna (Spain)

    2004-02-01

    The application of a statistical method, the local polynomial regression method, (LPRM), based on a nonparametric estimation of the regression function to determine the critical micelle concentration (cmc) is presented. The method is extremely flexible because it does not impose any parametric model on the subjacent structure of the data but rather allows the data to speak for themselves. Good concordance of cmc values with those obtained by other methods was found for systems in which the variation of a measured physical property with concentration showed an abrupt change. When this variation was slow, discrepancies between the values obtained by LPRM and others methods were found. (orig.)

  15. AN OPTIMAL REPLENISHMENT POLICY FOR DETERIORATING ITEMS WITH RAMP TYPE DEMAND UNDER PERMISSIBLE DELAY IN PAYMENTS

    Directory of Open Access Journals (Sweden)

    Dr. Sanjay Jain

    2010-10-01

    Full Text Available The aim of this paper is to develop an optimal replenishment policy for inventory models of deteriorating items with ramp type demand under permissible delay in payments. Deterioration of items begins on their arrival in stock.  An example is also presented to illustrate the application of developed model.

  16. Evaluation of trends for iron and manganese concentrations in wells, reservoirs, and water distribution networks, Qom city, Iran

    Directory of Open Access Journals (Sweden)

    Mohammad Fahiminia

    2015-06-01

    Full Text Available Background: This study aimed to evaluated trends for iron and manganese concentrations in wells, reservoirs, and water distribution networks in Qom city during the summer of 2012. Methods: This was a cross-sectional study. The studied scopes consisted of groundwater (60 wells, reservoirs (10 tanks, and water distribution network (33 points. One sample was taken from each source monthly. Statistical tests used included post hoc tests (Tukey HSD. Finally, the results were compared with drinking water standards. Results: The average concentrations of iron in groundwater, reservoirs, and distribution networks were 0.09, 0.07, and 0.07 mg/l, respectively. The average concentrations of manganese in groundwater, reservoirs, and distribution networks were 0.15, 0.09, and 0.1 mg/l, respectively. The turbidity averages in groundwater, reservoirs, and distribution networks were 0.58, 0.6, and 0.52 NTU, respectively. The average concentrations of free chlorine residual in water reservoirs and distribution networks were 1.74 and 1.06 mg/l, respectively. The pH averages in groundwater, reservoirs, and distribution networks were 7.4, 7.7, and 7.5, respectively. The amounts of iron, manganese, turbidity, free chlorine residual, and pH in the investigated resources had no significant differences (P > 0.05. Conclusion: The amounts of iron, manganese, turbidity, free chlorine residual and pH in groundwater, reservoirs, and water distribution networks of Qom are within permissible limits of national standards and EPA guidelines. Only the amount of manganese was higher than the Environmental Protection Agency (EPA permissible limit.

  17. Maximum permissible dietary contamination after the accidental release of radioactive materials from a nuclear reactor

    Energy Technology Data Exchange (ETDEWEB)

    Pochin, E E; Rock Carling, Ernest; Court Brown, W M [Medical Research Council, Committee on Protection against Ionizing Radiations, London (United Kingdom); and others

    1960-12-01

    After the accident to No. 1 pile at Windscale on October 10, 1957 (Atomic Energy Office, 1957), the Atomic Energy Authority asked the Medical Research Council for advice on the maximum intake of certain radioactive isotopes that should be regarded as permissible, under emergency conditions, for members of the general population living in, or deriving food from, an area contaminated owing to an accident to a reactor. The Council's Committee on Protection against Ionizing Radiations, together with its Subcommittees on Internal and External Radiations, has considered this problem, and concludes that the intake of radioactive materials by ingestion of contaminated food would generally be the limiting source of hazard after any such accident. Intake by inhalation, or radiation from the exterior, would become of importance only in rather special circumstances. In the following report, therefore, the Committee proposes maximum permissible levels of dietary contamination for the relevant isotopes in the emergency conditions envisaged. In proposing these levels, the Protection Committee has used the fullest information available on the radiation doses that would be delivered to different body tissues and at different ages by the isotopes concerned, and on the ways in which these materials would enter the body.

  18. Maximum permissible dietary contamination after the accidental release of radioactive materials from a nuclear reactor

    International Nuclear Information System (INIS)

    Pochin, E.E.; Rock Carling, Ernest; Court Brown, W.M.

    1960-01-01

    After the accident to No. 1 pile at Windscale on October 10, 1957 (Atomic Energy Office, 1957), the Atomic Energy Authority asked the Medical Research Council for advice on the maximum intake of certain radioactive isotopes that should be regarded as permissible, under emergency conditions, for members of the general population living in, or deriving food from, an area contaminated owing to an accident to a reactor. The Council's Committee on Protection against Ionizing Radiations, together with its Subcommittees on Internal and External Radiations, has considered this problem, and concludes that the intake of radioactive materials by ingestion of contaminated food would generally be the limiting source of hazard after any such accident. Intake by inhalation, or radiation from the exterior, would become of importance only in rather special circumstances. In the following report, therefore, the Committee proposes maximum permissible levels of dietary contamination for the relevant isotopes in the emergency conditions envisaged. In proposing these levels, the Protection Committee has used the fullest information available on the radiation doses that would be delivered to different body tissues and at different ages by the isotopes concerned, and on the ways in which these materials would enter the body

  19. From the Cover: Selective Enhancement of Domoic Acid Toxicity in Primary Cultures of Cerebellar Granule Cells by Lowering Extracellular Na+ Concentration.

    Science.gov (United States)

    Pérez-Gómez, Anabel; Cabrera-García, David; Warm, Davide; Marini, Ann M; Salas Puig, Javier; Fernández-Sánchez, Maria Teresa; Novelli, Antonello

    2018-01-01

    Domoic acid (DOM) is an excitatory amino acid analog of kainic acid (KA) that acts through glutamic acid (GLU) receptors, inducing a fast and potent neurotoxic response. Here, we present evidence for an enhancement of excitotoxicity following exposure of cultured cerebellar granule cells to DOM in the presence of lower than physiological Na+ concentrations. The concentration of DOM that reduced by 50% neuronal survival was approximately 3 µM in Na+-free conditions and 16 µM in presence of a physiological concentration of extracellular Na+. The enhanced neurotoxic effect of DOM was fully prevented by AMPA/KA receptor antagonist, while N-methyl-D-aspartate-receptor-mediated neurotoxicity did not seem to be involved, as the absence of extracellular Na+ failed to potentiate GLU excitotoxicity under the same experimental conditions. Lowering of extracellular Na+ concentration to 60 mM eliminated extracellular recording of spontaneous electrophysiological activity from cultured neurons grown on a multi electrode array and prevented DOM stimulation of the electrical activity. Although changes in the extracellular Na+ concentration did not alter the magnitude of the rapid increase in intracellular Ca2+ levels associated to DOM exposure, they did change significantly the contribution of voltage-sensitive calcium channels (VScaCs) and the recovery time to baseline. The prevention of Ca2+ influx via VSCaCs by nifedipine failed to prevent DOM toxicity at any extracellular Na+ concentration, while the reduction of extracellular Ca2+ concentration ameliorated DOM toxicity only in the absence of extracellular Na+, enhancing it in physiological conditions. Our data suggest a crucial role for extracellular Na+ concentration in determining excitotoxicity by DOM. © The Author 2017. Published by Oxford University Press on behalf of the Society of Toxicology. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  20. Trophic calculations reveal the mechanism of population-level variation in mercury concentrations between marine ecosystems: Case studies of two polar seabirds

    International Nuclear Information System (INIS)

    Brasso, Rebecka L.; Polito, Michael J.

    2013-01-01

    Highlights: • Ecosystem-specific baseline and consumer δ 15 N paired for population-specific trophic level. • Source of population-level variation in mercury exposure identified in two seabirds. • High mercury and trophic position suggests trophic driver of population-level variation. • Trophic similarities, differing mercury reveals geographic differences in bioavailability. -- Abstract: The incorporation of quantitative trophic level analysis in ecotoxicological studies provides explanatory power to identify the factors, trophic or environmental, driving population-level variation in mercury exposure at large geographic scales. In the Antarctic marine ecosystem, mercury concentrations and stable isotope values in Adélie penguins (Pygoscelis adeliae) were compared between the Antarctic Peninsula and the Ross Sea. Correcting tissue δ 15 N values for baseline δ 15 N values revealed population-level differences in trophic position which contributes to differences in mercury. Data from Thick-billed murres (Uria lomvia) were synthesized from published values from Baffin Bay and Svalbard to demonstrate the utility of baseline δ 15 N values in identifying differences in environmental mercury exposure independent of diet. Here, we demonstrate the importance of calculating population-specific trophic level data to uncover the source of variation in mercury concentrations between geographically distinct populations of marine predators

  1. Does an 'activity-permissive' workplace change office workers' sitting and activity time?

    Science.gov (United States)

    Gorman, Erin; Ashe, Maureen C; Dunstan, David W; Hanson, Heather M; Madden, Ken; Winkler, Elisabeth A H; McKay, Heather A; Healy, Genevieve N

    2013-01-01

    To describe changes in workplace physical activity, and health-, and work-related outcomes, in workers who transitioned from a conventional to an 'activity-permissive' workplace. A natural pre-post experiment conducted in Vancouver, Canada in 2011. A convenience sample of office-based workers (n=24, 75% women, mean [SD] age = 34.5 [8.1] years) were examined four months following relocation from a conventional workplace (pre) to a newly-constructed, purpose-built, movement-oriented physical environment (post). Workplace activity- (activPAL3-derived stepping, standing, and sitting time), health- (body composition and fasting cardio-metabolic blood profile), and work- (performance; job satisfaction) related outcomes were measured pre- and post-move and compared using paired t-tests. Pre-move, on average (mean [SD]) the majority of the day was spent sitting (364 [43.0] mins/8-hr workday), followed by standing (78.2 [32.1] mins/8-hr workday) and stepping (37.7 [15.6] mins/8-hr workday). The transition to the 'activity-permissive' workplace resulted in a significant increase in standing time (+18.5, 95% CI: 1.8, 35.2 mins/8-hr workday), likely driven by reduced sitting time (-19.7, 95% CI: -42.1, 2.8 mins/8-hr workday) rather than increased stepping time (+1.2, 95% CI: -6.2, 8.5 mins/8-hr workday). There were no statistically significant differences observed in health- or work-related outcomes. This novel, opportunistic study demonstrated that the broader workplace physical environment can beneficially impact on standing time in office workers. The long-term health and work-related benefits, and the influence of individual, organizational, and social factors on this change, requires further evaluation.

  2. Does an 'activity-permissive' workplace change office workers' sitting and activity time?

    Directory of Open Access Journals (Sweden)

    Erin Gorman

    Full Text Available To describe changes in workplace physical activity, and health-, and work-related outcomes, in workers who transitioned from a conventional to an 'activity-permissive' workplace.A natural pre-post experiment conducted in Vancouver, Canada in 2011. A convenience sample of office-based workers (n=24, 75% women, mean [SD] age = 34.5 [8.1] years were examined four months following relocation from a conventional workplace (pre to a newly-constructed, purpose-built, movement-oriented physical environment (post. Workplace activity- (activPAL3-derived stepping, standing, and sitting time, health- (body composition and fasting cardio-metabolic blood profile, and work- (performance; job satisfaction related outcomes were measured pre- and post-move and compared using paired t-tests.Pre-move, on average (mean [SD] the majority of the day was spent sitting (364 [43.0] mins/8-hr workday, followed by standing (78.2 [32.1] mins/8-hr workday and stepping (37.7 [15.6] mins/8-hr workday. The transition to the 'activity-permissive' workplace resulted in a significant increase in standing time (+18.5, 95% CI: 1.8, 35.2 mins/8-hr workday, likely driven by reduced sitting time (-19.7, 95% CI: -42.1, 2.8 mins/8-hr workday rather than increased stepping time (+1.2, 95% CI: -6.2, 8.5 mins/8-hr workday. There were no statistically significant differences observed in health- or work-related outcomes.This novel, opportunistic study demonstrated that the broader workplace physical environment can beneficially impact on standing time in office workers. The long-term health and work-related benefits, and the influence of individual, organizational, and social factors on this change, requires further evaluation.

  3. Atmospheric relative concentrations in building wakes

    International Nuclear Information System (INIS)

    Ramsdell, J.V. Jr.; Simonen, C.A.

    1997-05-01

    This report documents the ARCON96 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Reactor Regulation for potential use in control room habitability assessments. It includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON96 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more than five percent of the time. The concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. ARCON96 is a revised version of ARCON95, which was developed for the NRC Office of Nuclear Regulatory Research. Changes in the code permit users to simulate releases from area sources as well as point sources. The method of averaging concentrations for periods longer than 2 hours has also been changed. The change in averaging procedures increases relative concentrations for these averaging periods. In general, the increase in concentrations is less than a factor of two. The increase is greatest for relatively short averaging periods, for example 0 to 8 hours and diminishes as the duration of the averaging period increases

  4. Numerical methods for calculating thermal residual stresses and hydrogen diffusion

    International Nuclear Information System (INIS)

    Leblond, J.B.; Devaux, J.; Dubois, D.

    1983-01-01

    Thermal residual stresses and hydrogen concentrations are two major factors intervening in cracking phenomena. These parameters were numerically calculated by a computer programme (TITUS) using the FEM, during the deposition of a stainless clad on a low-alloy plate. The calculation was performed with a 2-dimensional option in four successive steps: thermal transient calculation, metallurgical transient calculation (determination of the metallurgical phase proportions), elastic-plastic transient (plain strain conditions), hydrogen diffusion transient. Temperature and phase dependence of hydrogen diffusion coefficient and solubility constant. The following results were obtained: thermal calculations are very consistent with experiments at higher temperatures (due to the introduction of fusion and solidification latent heats); the consistency is not as good (by 70 degrees) for lower temperatures (below 650 degrees C); this was attributed to the non-introduction of gamma-alpha transformation latent heat. The metallurgical phase calculation indicates that the heat affected zone is almost entirely transformed into bainite after cooling down (the martensite proportion does not exceed 5%). The elastic-plastic calculations indicate that the stresses in the heat affected zone are compressive or slightly tensile; on the other hand, higher tensile stresses develop on the boundary of the heat affected zone. The transformation plasticity has a definite influence on the final stress level. The return of hydrogen to the clad during the bainitic transformation is but an incomplete phenomenon and the hydrogen concentration in the heat affected zone after cooling down to room temperature is therefore sufficient to cause cold cracking (if no heat treatment is applied). Heat treatments are efficient in lowering the hydrogen concentration. These results enable us to draw preliminary conclusions on practical means to avoid cracking. (orig.)

  5. Bulk density calculations from prompt gamma ray yield

    International Nuclear Information System (INIS)

    Naqvi, A.A.; Nagadi, M.M.; Al-Amoudi, O.S.B.; Maslehuddin, M.

    2006-01-01

    Full text: The gamma ray yield from a Prompt Gamma ray Neutron Activation Analysis (PGNAA) setup is a linear function of element concentration and neutron flux in a the sample with constant bulk density. If the sample bulk density varies as well, then the element concentration and the neutron flux has a nonlinear correlation with the gamma ray yield [1]. The measurement of gamma ray yield non-linearity from samples and a standard can be used to estimate the bulk density of the samples. In this study the prompt gamma ray yield from Blast Furnace Slag, Fly Ash, Silica Fumes and Superpozz cements samples have been measured as a function of their calcium and silicon concentration using KFUPM accelerator-based PGNAA setup [2]. Due to different bulk densities of the blended cement samples, the measured gamma ray yields have nonlinear correlation with calcium and silicon concentration of the samples. The non-linearity in the yield was observed to increase with gamma rays energy and element concentration. The bulk densities of the cement samples were calculated from ratio of gamma ray yield from blended cement and that from a Portland cement standard. The calculated bulk densities have good agreement with the published data. The result of this study will be presented

  6. Importance of Upper-Limb Inertia in Calculating Concentric Bench Press Force

    OpenAIRE

    RAMBAUD, O; RAHMANI, A; MOYEN, B; BOURDIN, M

    2008-01-01

    The purpose of this study was to investigate the influence of upper-limb inertia on the force-velocity relationship and maximal power during concentric bench press exercise. Reference peak force values (Fpeakp) measured with a force plate positioned below the bench were compared to those measured simultaneously with a kinematic device fixed on the barbell by taking (Fpeakt) or not taking (Fpeakb) upper-limb inertia into account. Thirteen men (27.8 6 4.1 years, 184.6 6 5.5 cm, 99.5 6 18.6 kg) ...

  7. Calculation method for gamma dose rates from Gaussian puffs

    Energy Technology Data Exchange (ETDEWEB)

    Thykier-Nielsen, S; Deme, S; Lang, E

    1995-06-01

    The Lagrangian puff models are widely used for calculation of the dispersion of releases to the atmosphere. Basic output from such models is concentration of material in the air and on the ground. The most simple method for calculation of the gamma dose from the concentration of airborne activity is based on the semi-infinite cloud model. This method is however only applicable for puffs with large dispersion parameters, i.e. for receptors far away from the release point. The exact calculation of the cloud dose using volume integral requires large computer time usually exceeding what is available for real time calculations. The volume integral for gamma doses could be approximated by using the semi-infinite cloud model combined with correction factors. This type of calculation procedure is very fast, but usually the accuracy is poor because only a few of the relevant parameters are considered. A multi-parameter method for calculation of gamma doses is described here. This method uses precalculated values of the gamma dose rates as a function of E{sub {gamma}}, {sigma}{sub y}, the asymmetry factor - {sigma}{sub y}/{sigma}{sub z}, the height of puff center - H and the distance from puff center R{sub xy}. To accelerate the calculations the release energy, for each significant radionuclide in each energy group, has been calculated and tabulated. Based on the precalculated values and suitable interpolation procedure the calculation of gamma doses needs only short computing time and it is almost independent of the number of radionuclides considered. (au) 2 tabs., 15 ills., 12 refs.

  8. Calculation method for gamma dose rates from Gaussian puffs

    International Nuclear Information System (INIS)

    Thykier-Nielsen, S.; Deme, S.; Lang, E.

    1995-06-01

    The Lagrangian puff models are widely used for calculation of the dispersion of releases to the atmosphere. Basic output from such models is concentration of material in the air and on the ground. The most simple method for calculation of the gamma dose from the concentration of airborne activity is based on the semi-infinite cloud model. This method is however only applicable for puffs with large dispersion parameters, i.e. for receptors far away from the release point. The exact calculation of the cloud dose using volume integral requires large computer time usually exceeding what is available for real time calculations. The volume integral for gamma doses could be approximated by using the semi-infinite cloud model combined with correction factors. This type of calculation procedure is very fast, but usually the accuracy is poor because only a few of the relevant parameters are considered. A multi-parameter method for calculation of gamma doses is described here. This method uses precalculated values of the gamma dose rates as a function of E γ , σ y , the asymmetry factor - σ y /σ z , the height of puff center - H and the distance from puff center R xy . To accelerate the calculations the release energy, for each significant radionuclide in each energy group, has been calculated and tabulated. Based on the precalculated values and suitable interpolation procedure the calculation of gamma doses needs only short computing time and it is almost independent of the number of radionuclides considered. (au) 2 tabs., 15 ills., 12 refs

  9. Correlation for predicting aerosol concentration in sodium spray fires

    International Nuclear Information System (INIS)

    Marimuthu, K.

    2001-01-01

    Aerosol behaviour computer codes are reported for the study of time-dependent airborne aerosol concentration in a containment. The use of available computer codes requires a thorough knowledge of the various rate processes employed to describe the aerosol behaviour. The present work describes a simple empirical equation to calculate sodium fire aerosol concentration with respect to time in a containment and is applicable to sodium spray fire conditions. Sodium spray fire aerosol concentration values obtained using this simplified approach agree reasonably well with experimental results. The empirical equation described in the present work is incorporated in the spray fire code NACOM and the code calculated values of aerosol concentration agreement with the sodium spray fire experimental results is reasonably good. (author)

  10. MCNP calculation for calibration curve of X-ray fluorescence analysis

    International Nuclear Information System (INIS)

    Tan Chunming; Wu Zhifang; Guo Xiaojing; Xing Guilai; Wang Zhentao

    2011-01-01

    Due to the compositional variation of the sample, linear relationship between the element concentration and fluorescent intensity will not be well maintained in most X-ray fluorescence analysis. To overcome this, we use MCNP program to simulate fluorescent intensity of Fe (0∼100% concentration range) within binary mixture of Cr and O which represent typical strong absorption and weak absorption conditions respectively. The theoretic calculation shows that the relationship can be described as a curve determined by parameter p and value of p can be obtained with given absorption coefficient of substrate elements and element under detection. MCNP simulation results are consistent with theoretic calculation. Our research reveals that MCNP program can calculate the Calibration Curve of X-ray fluorescence very well. (authors)

  11. Uncertainty calculations for the measurement of in vivo bone lead by x-ray fluorescence

    International Nuclear Information System (INIS)

    O'Meara, J M; Fleming, D E B

    2009-01-01

    In order to quantify the bone lead concentration from an in vivo x-ray fluorescence measurement, typically two estimates of the lead concentration are determined by comparing the normalized x-ray peak amplitudes from the Kα 1 and Kβ 1 features to those of the calibration phantoms. In each case, the normalization consists of taking the ratio of the x-ray peak amplitude to the amplitude of the coherently scattered photon peak in the spectrum. These two Pb concentration estimates are then used to determine the weighted mean lead concentration of that sample. In calculating the uncertainties of these measurements, it is important to include any covariance terms where appropriate. When determining the uncertainty of the lead concentrations from each x-ray peak, the standard approach does not include covariance between the x-ray peaks and the coherently scattered feature. These spectral features originate from two distinct physical processes, and therefore no covariance between these features can exist. Through experimental and simulated data, we confirm that there is no observed covariance between the detected Pb x-ray peaks and the coherently scattered photon signal, as expected. This is in direct contrast to recent work published by Brito (2006 Phys. Med. Biol. 51 6125-39). There is, however, covariance introduced in the calculation of the weighted mean lead concentration due to the common coherent normalization. This must be accounted for in calculating the uncertainty of the weighted mean lead concentration, as is currently the case. We propose here an alternative approach to calculating the weighted mean lead concentration in such a way as to eliminate the covariance introduced by the common coherent normalization. It should be emphasized that this alternative approach will only apply in situations in which the calibration line intercept is not included in the calculation of the Pb concentration from the spectral data: when the source of the intercept is well

  12. 76 FR 6136 - Notice of Proposals To Engage in Permissible Nonbanking Activities or To Acquire Companies That...

    Science.gov (United States)

    2011-02-03

    ...: 1. Hana Financial Group Inc., Seoul, Korea; to acquire a controlling interest in Korea Exchange Bank, Seoul, Korea, and thereby indirectly acquire voting shares of KEB Financial Corp., New York, New York... FEDERAL RESERVE SYSTEM Notice of Proposals To Engage in Permissible Nonbanking Activities or To...

  13. 75 FR 71130 - Notice of Proposals To Engage in Permissible Nonbanking Activities or To Acquire Companies That...

    Science.gov (United States)

    2010-11-22

    ... FEDERAL RESERVE SYSTEM Notice of Proposals To Engage in Permissible Nonbanking Activities or To..., Virginia 23261-4528: 1. Royal Bank of Canada, Montreal, Canada; to acquire BlueBay Asset Management plc..., and thereby engage in financial and investment advisory activities, pursuant to section 225.28(b)(6...

  14. Heavy metals concentrations in water bodies around aquamarine ...

    African Journals Online (AJOL)

    Water samples from three streams in the mining area of Eggon Hill were analysed. The Physicochemical values obtained were compared with WHO permissible standards in drinking water. Except for Cu and Zn with levels within permissible limits, other heavy metals determined were found to have levels above the WHO ...

  15. In Vitro Measles Virus Infection of Human Lymphocyte Subsets Demonstrates High Susceptibility and Permissiveness of both Naive and Memory B Cells.

    Science.gov (United States)

    Laksono, Brigitta M; Grosserichter-Wagener, Christina; de Vries, Rory D; Langeveld, Simone A G; Brem, Maarten D; van Dongen, Jacques J M; Katsikis, Peter D; Koopmans, Marion P G; van Zelm, Menno C; de Swart, Rik L

    2018-04-15

    Measles is characterized by a transient immune suppression, leading to an increased risk of opportunistic infections. Measles virus (MV) infection of immune cells is mediated by the cellular receptor CD150, expressed by subsets of lymphocytes, dendritic cells, macrophages, and thymocytes. Previous studies showed that human and nonhuman primate memory T cells express higher levels of CD150 than naive cells and are more susceptible to MV infection. However, limited information is available about the CD150 expression and relative susceptibility to MV infection of B-cell subsets. In this study, we assessed the susceptibility and permissiveness of naive and memory T- and B-cell subsets from human peripheral blood or tonsils to in vitro MV infection. Our study demonstrates that naive and memory B cells express CD150, but at lower frequencies than memory T cells. Nevertheless, both naive and memory B cells proved to be highly permissive to MV infection. Furthermore, we assessed the susceptibility and permissiveness of various functionally distinct T and B cells, such as helper T (T H ) cell subsets and IgG- and IgA-positive memory B cells, in peripheral blood and tonsils. We demonstrated that T H 1T H 17 cells and plasma and germinal center B cells were the subsets most susceptible and permissive to MV infection. Our study suggests that both naive and memory B cells, along with several other antigen-experienced lymphocytes, are important target cells of MV infection. Depletion of these cells potentially contributes to the pathogenesis of measles immune suppression. IMPORTANCE Measles is associated with immune suppression and is often complicated by bacterial pneumonia, otitis media, or gastroenteritis. Measles virus infects antigen-presenting cells and T and B cells, and depletion of these cells may contribute to lymphopenia and immune suppression. Measles has been associated with follicular exhaustion in lymphoid tissues in humans and nonhuman primates, emphasizing the

  16. 12 CFR 584.2-2 - Permissible bank holding company activities of savings and loan holding companies.

    Science.gov (United States)

    2010-01-01

    ... savings and loan holding companies. 584.2-2 Section 584.2-2 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY SAVINGS AND LOAN HOLDING COMPANIES § 584.2-2 Permissible bank holding company activities of savings and loan holding companies. (a) General. For purposes of § 584.2(b)(6)(i) of this part...

  17. Group Waterpipe Tobacco Smoking Increases Smoke Toxicant Concentration.

    Science.gov (United States)

    Ramôa, Carolina P; Shihadeh, Alan; Salman, Rola; Eissenberg, Thomas

    2016-05-01

    Waterpipe tobacco smoking is a global health concern. Laboratory research has focused on individual waterpipe users while group use is common. This study examined user toxicant exposure and smoke toxicant yield associated with individual and group waterpipe smoking. Twenty-two pairs of waterpipe smokers used a waterpipe individually and as a dyad. Before and after smoking, blood was sampled and expired carbon monoxide (CO) measured; puff topography was recorded throughout. One participant from each pair was selected randomly and their plasma nicotine and expired air CO concentrations were compared when smoking alone to when smoking as part of a dyad. Recorded puff topography was used to machine-produce smoke that was analyzed for toxicant content. There was no difference in mean plasma nicotine concentration when an individual smoked as part of a dyad (mean = 14.9 ng/ml; standard error of the mean [SEM] = 3.0) compared to when smoking alone (mean = 10.0 ng/ml; SEM = 1.5). An individual smoking as part of as a dyad had, on average, lower CO (mean = 15.8 ppm; SEM = 2.0) compared to when smoking alone (mean= 21.3 ppm; SEM = 2.7). When two participants smoked as a dyad they took, on average, more puffs (mean = 109.8; SEM = 7.6) than a singleton smoker (mean = 77.7; SEM = 8.1) and a shorter interpuff interval (IPI; dyad mean = 23.8 seconds; SEM = 1.9; singleton mean = 40.8 seconds; SEM = 4.8). Higher concentrations of several toxicants were observed in dyad-produced smoke. Dyad smoking may increase smoke toxicant content, likely due to the dyad's shorter IPIs and greater puff number. More work is needed to understand if group waterpipe smoking alters the health risks of waterpipe tobacco smoking. This study is the first to measure toxicants in smoke generated from a waterpipe when used by a dyad. Relative to smoke generated by a singleton, dyad smoke had higher concentration of some toxicants. These differences may be attributed to differences in puffing behavior

  18. Magnetic properties of vanadium doped CdTe: Ab initio calculations

    Energy Technology Data Exchange (ETDEWEB)

    Goumrhar, F. [Laboratory of Physics of High Energy, Modeling & Simulations (LPHE-MS), Faculty of Sciences, Mohammed V University of Rabat, Av. Ibn Batouta, B.P. 1014 Rabat (Morocco); Bahmad, L., E-mail: bahmad@fsr.ac.ma [Laboratory of Magnetism and High Energy Physics (LMPHE-URAC12), Faculty of Sciences, Mohammed V University of Rabat, Av. Ibn Batouta, B.P. 1014 Rabat (Morocco); Mounkachi, O. [Material and Nanomaterial Center, MAScIR Fondation, Rabat (Morocco); Benyoussef, A. [Laboratory of Magnetism and High Energy Physics (LMPHE-URAC12), Faculty of Sciences, Mohammed V University of Rabat, Av. Ibn Batouta, B.P. 1014 Rabat (Morocco); Material and Nanomaterial Center, MAScIR Fondation, Rabat (Morocco); Hassan II Academy of Sciences and Technology, Rabat (Morocco)

    2017-04-15

    In this paper, we are applying the ab initio calculations to study the magnetic properties of vanadium doped CdTe. This study is based on the Korringa–Kohn–Rostoker method (KKR) combined with the coherent potential approximation (CPA), within the local density approximation (LDA). This method is called KKR-CPA-LDA. We have calculated and plotted the density of states (DOS) in the energy diagram for different concentrations of dopants. We have also investigated the magnetic and half-metallic properties of this compound and shown the mechanism of exchange interaction. Moreover, we have estimated the Curie temperature T{sub c} for different concentrations. Finally, we have shown how the crystal field and the exchange splittings vary as a function of the concentrations.

  19. Systematic Approach to Calculate the Concentration of Chemical Species in Multi-Equilibrium Problems

    Science.gov (United States)

    Baeza-Baeza, Juan Jose; Garcia-Alvarez-Coque, Maria Celia

    2011-01-01

    A general systematic approach is proposed for the numerical calculation of multi-equilibrium problems. The approach involves several steps: (i) the establishment of balances involving the chemical species in solution (e.g., mass balances, charge balance, and stoichiometric balance for the reaction products), (ii) the selection of the unknowns (the…

  20. Fluoride Concentration of Drinking-Water of Qom, Iran

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yari

    2016-03-01

    Full Text Available Background and Purpose: Fluoride is a natural element essential for human nutrition due to its benefits for dental enamel. It is well-documented that standard amounts of fluoride in drinkingwater can decrease the rate of dental caries. This study was conducted with the aim of measuring fluoride concentration of drinking-water supplies and urban distribution system in Qom, Iran. Materials and Methods: Results were subsequently compared against national and international standards. All sources of drinking-water of rural and urban areas were examined. To measure fluoride, the standard SPADNS method and a DR/4000s spectrophotometer were used. Results: Results showed that the mean of fluoride concentration in rural areas, mainly supplied with groundwater sources, was 0.41 mg/L, that of the urban distribution system 0.82 mg/L, that of Ali-Abad station 0.11 mg/L, and that of the private water desalination system 0.24 mg/L. Due to the hot climate of Qom, fluoride concentration means of all sources were lower than the permissible standards set by Iranian Standards and the WHO guidelines (except those of some of the groundwater sources and urban distribution systems. Conclusion: It seems that in most of the drinking-water sources the average fluoride concentration is not enough to prevent dental caries or strengthen dental enamel. It is concluded that Qom’s drinkingwater would require at least 0.4 mg/L to reach the minimum desirable standard.

  1. Seismic calculations for underground reactor buildings

    International Nuclear Information System (INIS)

    Altes, J.; Koschmieder, D.

    1977-08-01

    Embedding the buildings in soil changes their seismic response behaviour as compared to surface buildings, i.e. higher stiffness and increased radiation damping is attained. Finite element models are best suited for determinig the effects of embedment and of layered subsoil. The code used was the LUSH2-programme, which is applicable to 2-dimensional problems and provides an approximate treatment for non-linear dynamic soil behaviour. For embedded buildings there is a good agreement between 2- and 3-dimensional models of the response for points below the soil surface. It is therefore permissible to use the less costly 2-dimensional programmes. To simulate earthquake, three different acceleration-time histories, derived from actual measurements and from artificial synthesis, with differing response spectra were fed in. The soil characteristics assumed are applicable to a representative site in Germany. Three different types of models were examined, using analytical models with only a few elements for parametric studies and with up to 716 elements for more precise calculations. A comparison was made between the semi-embedment, the total embedment, and installation of the reactor building above-ground. (orig.) [de

  2. Leishmania major glycosylation mutants require phosphoglycans (lpg2- but not lipophosphoglycan (lpg1- for survival in permissive sand fly vectors.

    Directory of Open Access Journals (Sweden)

    Anna Svárovská

    2010-01-01

    Full Text Available Sand fly species able to support the survival of the protozoan parasite Leishmania have been classified as permissive or specific, based upon their ability to support a wide or limited range of strains and/or species. Studies of a limited number of fly/parasite species combinations have implicated parasite surface molecules in this process and here we provide further evidence in support of this proposal. We investigated the role of lipophosphoglycan (LPG and other phosphoglycans (PGs in sand fly survival, using Leishmania major mutants deficient in LPG (lpg1(-, and the phosphoglycan (PG-deficient mutant lpg2(-. The sand fly species used were the permissive species Phlebotomus perniciosus and P. argentipes, and the specific vector P. duboscqi, a species resistant to L. infantum development.The lpg2(- mutants did not survive well in any of the three sand fly species, suggesting that phosphoglycans and/or other LPG2-dependent molecules are required for parasite development. In vitro, all three L. major lines were equally resistant to proteolytic activity of bovine trypsin, suggesting that sand fly-specific hydrolytic proteases or other factors are the reason for the early lpg2(- parasite killing. The lpg1(- mutants developed late-stage infections in two permissive species, P. perniciosus and P. argentipes, where their infection rates and intensities of infections were comparable to the wild type (WT parasites. In contrast, in P. duboscqi the lpg1(- mutants developed significantly worse than the WT parasites.In combination with previous studies, the data establish clearly that LPG is not required for Leishmania survival in permissive species P. perniciosus and P. argentipes but plays an important role in the specific vector P. duboscqi. With regard to PGs other than LPG, the data prove the importance of LPG2-related molecules for survival of L. major in the three sand fly species tested.

  3. Analysis of Particulate matter (PM 10 and PM 2.5 concentration in Khorramabad city

    Directory of Open Access Journals (Sweden)

    Seyed Hamed Mirhosseini

    2013-01-01

    Full Text Available Aims: In this study, the concentration of PM10 and PM2.5 in eight station of Khorramabad city was analyzed. Materials and Methods: For this study, the data were taken from April 2010 to March 2011. The eight sampling point were chosen in account to Khorramabad maps. During this period, 240 daily PM samples including coarse particle (PM 10 and fine particle (PM 2.5 were collected. A two-part sampler was used to collect samples of PM. According to one-way ANOVA, multiple comparisons Scheffe, the obtained data were analyzed and then compared with the Environment protection organization standard rates. Khorramabad Results: The results revealed that during measuring the maximum concentration of PM 10 and PM 2.5 was respectively 120.9 and 101.09 μ/m 3 at Shamshirabad station. There was a significant difference between the mean values of PM 10 concentration (μg/m 3 in the seasons of summer. In addition, the mean concentrations of PM 10 in warmer months exceeded to the maximum permissible concentration. Conclusions: Year comparison of PM 10 and PM 2.5 concentration with standard were revealed particle matter concentration in summer season was higher than standard. Although total mean of particle matter was less than standard concentration.

  4. Subcellular localization of Aleutian mink disease parvovirus proteins and DNA during permissive infection of Crandell feline kidney cells

    DEFF Research Database (Denmark)

    Oleksiewicz, M.B.; Costello, F.; Huhtanen, M.

    1996-01-01

    Confocal microscopy allowed us to localize viral nonstructural (NS) and capsid (VP) proteins and DNA simultaneously in cells permissively infected with Aleutian mink disease parvovirus (ADV). Early after infection, NS proteins colocalized with viral DNA to form intranuclear inclusions, whereas VP...

  5. Calculations of critical micelle concentration by dissipative particle dynamics simulations: the role of chain rigidity.

    Science.gov (United States)

    Lee, Ming-Tsung; Vishnyakov, Aleksey; Neimark, Alexander V

    2013-09-05

    Micelle formation in surfactant solutions is a self-assembly process governed by complex interplay of solvent-mediated interactions between hydrophilic and hydrophobic groups, which are commonly called heads and tails. However, the head-tail repulsion is not the only factor affecting the micelle formation. For the first time, we present a systematic study of the effect of chain rigidity on critical micelle concentration and micelle size, which is performed with the dissipative particle dynamics simulation method. Rigidity of the coarse-grained surfactant molecule was controlled by the harmonic bonds set between the second-neighbor beads. Compared to flexible molecules with the nearest-neighbor bonds being the only type of bonded interactions, rigid molecules exhibited a lower critical micelle concentration and formed larger and better-defined micelles. By varying the strength of head-tail repulsion and the chain rigidity, we constructed two-dimensional diagrams presenting how the critical micelle concentration and aggregation number depend on these parameters. We found that the solutions of flexible and rigid molecules that exhibited approximately the same critical micelle concentration could differ substantially in the micelle size and shape depending on the chain rigidity. With the increase of surfactant concentration, primary micelles of more rigid molecules were found less keen to agglomeration and formation of nonspherical aggregates characteristic of flexible molecules.

  6. Hydrogen storage on graphene: First-principle calculations

    NARCIS (Netherlands)

    Boukhvalov, D.W.; Katsnelson, M.I.; Lichtenstein, A.I.

    2007-01-01

    Density functional calculations of electronic structure, total energy, structural distortions, and magnetism for hydrogenated single-layer, bilayer, and multi-layer graphene are performed. It is found that hydrogen-induced magnetism can survives only at very low concentrations of hydrogen

  7. Measurement of activity concentration of primordial radionuclides in the soil samples of Tiruchirappalli, Tamil Nadu, India

    International Nuclear Information System (INIS)

    Sadiq Bukhari, A.; Saiyad Musthafa, M.; Syed Mohamed, H.E.; Krishnamoorthy, R.; Shahul Hameed, M.M.; Shahul Hameed, P.

    2008-01-01

    Full text: Radioactive minerals such as uranium ( 238 U), thorium ( 232 Th) and potassium ( 40 K) are considered to be Primordial radionuclides which are widely distributed in the earth's crust. Gamma-radiation from these radionuclides represents the main external source of irradiation for the human body. Human beings are exposed outdoors to the natural terrestrial radiation that originates predominantly from the upper 30 cm of the soil. A pilot project was therefore initiated aiming at systematically measuring the terrestrial gamma radiation in Tiruchirappalli city, Tamil Nadu, South India and to establish baseline data on the terrestrial background radiation level determining its contribution to the annual effective dose equivalent to the human population. The natural radioactivity concentrations were studied in soil samples collected from 50 locations in Tiruchirappalli city. The concentration varies significantly over different soil types and the highest radioactivity was measured over soil types of granite origin followed by red soil and alluvial loam. The mean activity concentrations of 232 Th, 238 U and 40 K in soil samples are found to be 81.78 Bq.kg -1 , 32.62 Bq.kg -1 , and 551.35 Bq.kg -1 respectively. The calculated gamma dose from the soil is in the range between 38.86nGy.h -1 and 240.59 nGy.h -1 with a mean value of 89.76 nGy.h -1 . The mean annual effective dose to the population from outdoor terrestrial gamma radiation was estimated to be 0.11mSv.y -1 which is low as compared with the maximum permissible effective dose equivalent of 1mSv.y -1 (ICRP,1991). In the present study it is observed that the major sources of gamma radiation in soils are mainly derived from rocky area with granite basement. (author)

  8. Concentration changes due to cathodic protection

    NARCIS (Netherlands)

    Gellings, P.J.

    1978-01-01

    By solving the appropriate diffusion equations the concentration changes are calculated in the environment of underground structures protected cathodically. It is shown that these changes are negligible under all practical circumstances.

  9. Determination of serum free thyroxine concentration (FT4) by means of fT4-fraction and total thyroxine concentration

    International Nuclear Information System (INIS)

    Passath, A.; Leb, G.

    1985-01-01

    A new equilibrium assay for the determination of serum free thyroxine was evaluated in 514 patients. The assay comprises a two-vial-procedure to measure total thyroxine and free thyroxine fraction by use of monoclonal antibodies. Free thyroxine concentrations are calculated from fT 4 -fraction and total thyroxine concentration readings. In euthyroidism the average free thyroxine fraction (%fT 4 ) was 0.011%, in hyperthyroidism this fraction was elevated, in hypothyroidism it was below normal. In patients with TBG anomalies, TBG values were inversely correlated with fT 4 fraction readings. The 'euthyroid reference range' of FT 4 (SPAC ET) was between 0.70 to 1.78ng/dl. This euthyroid range of FT 4 was determined from TT 4 concentrations measured by T 4 -RIA (SPAC T 4 MONO) which were 30% above TT 4 values measured by conventional T 4 -RIA (SPAC T 4 POLY; polyclonal antibodies). However, a different euthyroid range of FT 4 between 0.55 to 1.30 ng/dl was observed as well as by other investigators when conventional T 4 -RIA measurements were used for calculation of FT 4 values. Our results indicate that calculated FT 4 concentration values are highly dependent on the methods used for determination of total thyroxine concentrations. Precision and reproducability of this two vial equilibrium assay did not meet the requirements mandatory for the application as a clinical routine diagnostic procedure, and its general use for this purpose can as yet not be recommended. (Author)

  10. ATLAS cavern magnetic field calculations

    International Nuclear Information System (INIS)

    Vorojtsov, S.B.; Vorozhtsov, A.S.; Butin, F.; Price, M.

    2000-01-01

    A new approach has been adopted in an attempt to produce a complete ATLAS cavern B-field map using a more precise methodological approach (variable magnetisation, depending on the external field) and the latest design taking into account of the structural elements. The basic idea was to produce a dedicated basic TOSCA model and then to insert a series of ferromagnetic structure elements to monitor the perturbative effect on the basic field map. Eventually, it was found: the bedplate field perturbation is an order of magnitude above the permissible level; manufacturing of the bedplates from nonmagnetic material or careful evaluation of their field contribution in the event reconstruction codes is required; the field value at the rack positions is higher than the permissible one; the final position of racks should be chosen taking into account the detailed magnetic field distribution

  11. Plant assemblage composition and soil P concentration differentially affect communities of AM and total fungi in a semi-arid grassland.

    Science.gov (United States)

    Klabi, Rim; Bell, Terrence H; Hamel, Chantal; Iwaasa, Alan; Schellenberg, Mike; Raies, Aly; St-Arnaud, Marc

    2015-01-01

    Adding inorganic P- and N-fixing legumes to semi-arid grasslands can increase forage yield, but soil nutrient concentrations and plant cover may also interact to modify soil fungal populations, impacting short- and long-term forage production. We tested the effect of plant assemblage (seven native grasses, seven native grasses + the domesticated N-fixing legume Medicago sativa, seven native grasses + the native N-fixing legume Dalea purpurea or the introduced grass Bromus biebersteinii + M. sativa) and soil P concentration (addition of 0 or 200 P2O5 kg ha(-1) at sowing) on the diversity and community structure of arbuscular mycorrhizal (AM) fungi and total fungi over two consecutive years, using 454-pyrosequencing of 18S rDNA and ITS amplicons. Treatment effects were stronger in the wet year (2008) than the dry year (2009). The presence of an N-fixing legume with native grasses generally increased AM fungal diversity, while the interaction between soil P concentration and plant assemblage modified total fungal community structure in 2008. Excluding interannual variations, which are likely driven by moisture and plant productivity, AM fungal communities in semi-arid grasslands appear to be primarily affected by plant assemblage composition, while the composition of other fungi is more closely linked to soil P. © FEMS 2014. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  12. Calculation method for gamma-dose rates from spherical puffs

    International Nuclear Information System (INIS)

    Thykier-Nielsen, S.; Deme, S.; Lang, E.

    1993-05-01

    The Lagrangian puff-models are widely used for calculation of the dispersion of atmospheric releases. Basic output from such models are concentrations of material in the air and on the ground. The most simple method for calculation of the gamma dose from the concentration of airborne activity is based on semi-infinite cloud model. This method is however only applicable for points far away from the release point. The exact calculation of the cloud dose using the volume integral requires significant computer time. The volume integral for the gamma dose could be approximated by using the semi-infinite cloud model combined with correction factors. This type of calculation procedure is very fast, but usually the accuracy is poor due to the fact that the same correction factors are used for all isotopes. The authors describe a more elaborate correction method. This method uses precalculated values of the gamma-dose rate as a function of the puff dispersion parameter (δ p ) and the distance from the puff centre for four energy groups. The release of energy for each radionuclide in each energy group has been calculated and tabulated. Based on these tables and a suitable interpolation procedure the calculation of gamma doses takes very short time and is almost independent of the number of radionuclides. (au) (7 tabs., 7 ills., 12 refs.)

  13. Determination of trace metal concentration in compost, DAP, and TSP fertilizers by neutron activation analysis (NAA) and insights from density functional theory calculations.

    Science.gov (United States)

    Rahman, Md Sajjadur; Hossain, Syed Mohammod; Rahman, Mir Tamzid; Halim, Mohammad A; Ishtiak, Mohammad Niaz; Kabir, Mahbub

    2017-11-08

    Leaching of toxic metals from fertilizers is a growing concern in an agricultural country like Bangladesh due to the serious consequences in health and food chain. Fertilizers used in farming fields and nurseries (plant sales outlet) in the mid-southern part of Bangladesh were collected for the determination of toxic metals. This study employed the neutron activation method and a relative standardization approach. Three standard/certified reference materials, namely NIST coal fly ash 1633b, IAEA-Soil-7, and IAEA-SL-1 (lake sediment), were considered for elemental quantification. Concentration of As (2.63-16.73 mg/kg), Cr (40.93-261.77 mg/kg), Sb (0.47-63.58 mg/kg), Th (1.44-19.16 mg/kg), and U (1.90-209.41 mg/kg) were determined in fertilizers. High concentrations of Cr, Sb, and U were detected in some compost and phosphate fertilizers (TSP and diammonium phosphate (DAP)) in comparison with the IAEA/European market standard and other studies. Quantum mechanical calculations were performed to understand the molecular level interaction of CrO 3 , Sb 2 O 3 , and AsO 3 , with DAP by employing density functional theory with the B3LYP/SDD level of theory. Our results indicated that CrO 3 and Sb 2 O 3 have strong binding affinity with DAP compared to AsO 3 , which supports the experimental results. These compounds attached to the phosphate group through covalent-like bonding with oxygen. The frontier molecular orbital calculation indicated that HOMO-LUMO gap of the AsO 3 -DAP (5.46 eV) and Sb 2 O 3 -DAP (6.48 eV) complexes are relatively lower than the CrO 3 -DAP, which indicates that As and Sb oxides are chemically more prone to attach with the phosphate group of DAP fertilizer.

  14. Permissive attitude toward suicide and future intent in individuals with and without depression: results from a nationwide survey in Korea.

    Science.gov (United States)

    Jeon, Hong Jin; Park, Jae-Hyun; Shim, Eun-Jung

    2013-04-01

    Many previous studies have revealed that individuals with depression have higher thought of suicide, although not always exhibiting intent. We investigated the associated factors with respect to intent for suicide in the future. A total of 1584 adults were selected through a nationwide multistage probability sampling, randomly one person per household, and through face-to-face interviews (response rate was 63.4%) using the suicidality module of the Mini-International Neuropsychiatric Interview and the Patient Health Questionnaire-9. The group with depression (n = 152) revealed a significantly higher level of future suicide intent (t = 4.65, p attitude (t = 4.32, p attitude (adjusted odds ratio, 3.69; 95% confidence interval, 1.97-6.89) was the only factor significantly associated with future suicide intent, whereas age; sex; education years; monthly income; financial, job, and family stress; physical illness; lifetime suicide attempt; and depression showed no statistical significance. The group with depression showed significantly higher levels of future suicide intent than did the group without depression in those who had a higher permissive attitude (t = 4.18, p attitudes (t = 1.98, p = 0.067). Permissive attitude toward suicide was associated with intent for suicide in the future in individuals with depression. Permissive attitude could be evaluated and corrected to prevent suicide.

  15. 76 FR 46808 - Notice of Proposals To Engage in Permissible Nonbanking Activities or To Acquire Companies That...

    Science.gov (United States)

    2011-08-03

    ... that the Board has determined by Order to be closely related to banking and permissible for bank...: 1. Westpac Banking Corporation, Sydney, Australia; to indirectly acquire 100 percent of the voting... advisory and private placement services, pursuant to sections 225.28(b)(6) and (b)(7)(iii) of Regulation Y...

  16. Computational algorithm for molybdenite concentrate annealing

    International Nuclear Information System (INIS)

    Alkatseva, V.M.

    1995-01-01

    Computational algorithm is presented for annealing of molybdenite concentrate with granulated return dust and that of granulated molybdenite concentrate. The algorithm differs from the known analogies for sulphide raw material annealing by including the calculation of return dust mass in stationary annealing; the latter quantity varies form the return dust mass value obtained in the first iteration step. Masses of solid products are determined by distribution of concentrate annealing products, including return dust and benthonite. The algorithm is applied to computations for annealing of other sulphide materials. 3 refs

  17. Cohesion energy calculations for ternary ionic novel crystals

    International Nuclear Information System (INIS)

    Vazquez P, G.; Cabrera, E.; Mijangos, R.R.; Valdez, E.; Duarte, C.

    2001-01-01

    The present work calculates the value of the link energy of a crystalline ternary structure newly formed by alkali halides. The ternary structure prepared with different concentrations of KCl x KBrRbCl 2 maintains a very good miscibility and stability. The calculation is based on the use of a generalization of the Vegard law (which generally is valid for binary compounds) for calculating the values of the lattice constant and the repulsive m exponent. The value of the lattice parameter given by X-ray diffractometry agrees with the close approximation of the calculated value of the method used. It also compares the value of energy cohesion obtained by the Born expression with more complex approximations. (Author)

  18. Control of atmospheric CO2 concentrations by 2050: A calculation on the emission rights of different countries

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    This paper is to provide quantitative data on some critical issues in anticipation of the forthcoming international negotiations in Denmark on the control of atmospheric CO2 concentrations. Instead of letting only a small number of countries dominate a few controversial dialogues about emissions reductions, a comprehensive global system must be established based on emissions allowances for different countries, to realize the long-term goal of controlling global atmospheric CO2 concentrations. That a system rooted in "cumulative emissions per capita," the best conception of the "common but differentiated responsibilities" principle affirmed by the Kyoto Protocol according to fundamental standards of fairness and justice, was demonstrated. Based on calculations of various countries’ cumulative emissions per capita, estimates of their cumulative emissions from 1900 to 2005, and their annual emissions allowances into the future (2006―2050), a 470 ppmv atmospheric CO2 concentration target was set. According to the following four objective indicators―total emissions allowance from 1900 to 2050, actual emissions from 1900 to 2005, emissions levels in 2005, and the average growth rate of emissions from 1996 to 2005―all countries and regions whose population was more than 300000 in 2005 were divided into four main groups: countries with emissions deficits, countries and regions needing to reduce their gross emissions, countries and regions needing to reduce their emissions growth rates, and countries that can maintain the current emissions growth rates. Based on this proposal, most G8 countries by 2005 had already expended their 2050 emissions allowances. The accu-mulated financial value based on emissions has reached more than 5.5 trillion US dollars (20 dollars per ton of CO2). Even if these countries could achieve their ambitious emissions reduction targets in the future, their per capita emissions from 2006 to 2050 would still be much higher than those of

  19. Imperfect Reworking Process Consideration in Integrated Inventory Model under Permissible Delay in Payments

    Directory of Open Access Journals (Sweden)

    Ming-Cheng Lo

    2008-01-01

    Full Text Available This study develops an improved inventory model to help the enterprises to advance their profit increasing and cost reduction in a single vendor single-buyer environment with general demand curve, adjustable production rate, and imperfect reworking process under permissible delay in payments. For advancing practical use in a real world, we are concerned with the following strategy determining, which includes the buyer's optimal selling price, order quantity, and the number of shipments per production run from the vendor to the buyer. An algorithm and numerical analysis are used to illustrate the solution procedure.

  20. Study about chemical and radiological toxicity of rare earths

    International Nuclear Information System (INIS)

    Goncalez, O.L.

    1987-02-01

    The maximum permissible concentration in workplace air for an admixture of rare earths is calculated to be 1.47 mg/m 3 of air. This value takes into account the biological mean-life of those chemical elements in human body and acute toxicological data. A simplified mathematical models is done that describes the body content of this product as a time function, for cronic intoxication by air particulate inhalation. Under the radiological point of view the limit calculated for the air concentration is about 100 mg/m 3 , showing that the chemical toxity of these products is predominant. (Author) [pt

  1. Robot Lies in Health Care: When Is Deception Morally Permissible?

    Science.gov (United States)

    Matthias, Andreas

    2015-06-01

    Autonomous robots are increasingly interacting with users who have limited knowledge of robotics and are likely to have an erroneous mental model of the robot's workings, capabilities, and internal structure. The robot's real capabilities may diverge from this mental model to the extent that one might accuse the robot's manufacturer of deceiving the user, especially in cases where the user naturally tends to ascribe exaggerated capabilities to the machine (e.g. conversational systems in elder-care contexts, or toy robots in child care). This poses the question, whether misleading or even actively deceiving the user of an autonomous artifact about the capabilities of the machine is morally bad and why. By analyzing trust, autonomy, and the erosion of trust in communicative acts as consequences of deceptive robot behavior, we formulate four criteria that must be fulfilled in order for robot deception to be morally permissible, and in some cases even morally indicated.

  2. Concentration and speciation of heavy metals in six different sewage sludge-composts

    International Nuclear Information System (INIS)

    Cai Quanying; Mo Cehui; Wu Qitang; Zeng Qiaoyun; Katsoyiannis, Athanasios

    2007-01-01

    This study presents the concentrations and speciation of heavy metals (HMs) in six different composts of sewage sludges deriving from two wastewater treatment plants in China. After 56 days of sludge composting with rice straw at a low C/N ratio (13:1), cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) were enriched in sludge composts, exhibiting concentrations that varied from 0.75 to 2.0, 416 to 458, 66 to 168 and 1356 to 1750 mg kg -1 dry weight (d.w.), respectively. The concentrations increased by 12-60% for Cd, 8-17% for Cu, 15-43% for Pb and 14-44% for Zn compared to those in sewage sludges. The total concentrations of individual or total elements in the final composts exceeded the maximum permissible limits proposed for compost or fertilizer. In all the final composts, more than 70% of total Cu was associated with organic matter-bound fraction, while Zn was mainly concentrated in exchangeable and Fe-Mn oxide-bound fractions which implied the high mobility and bioavailability. Continuously aerated composting treatment exhibited better compost quality and lower potential toxicity of HMs, whereas inoculant with microorganism and enzyme spiked during composting had no obvious advantage on humification of organic matter and on reducing HM mobility and bioavailability

  3. A silencing suppressor protein (NSs) of a tospovirus enhances baculovirus replication in permissive and semipermissive insect cell lines.

    Science.gov (United States)

    Oliveira, Virgínia Carla; Bartasson, Lorrainy; de Castro, Maria Elita Batista; Corrêa, José Raimundo; Ribeiro, Bergmann Morais; Resende, Renato Oliveira

    2011-01-01

    The nonstructural protein (NSs) of the Tomato spotted wilt virus (TSWV) has been identified as an RNAi suppressor in plant cells. A recombinant Autographa californica multiple nucleopolyhedrovirus (AcMNPV) designated vAcNSs, containing the NSs gene under the control of the viral polyhedrin (polh) gene promoter, was constructed and the effects of NSs in permissive, semipermissive and nonpermissive insect cells to vAcNSs infection were evaluated. vAcNSs produced more budded virus when compared to wild type in semipermissive cells. Co-infection of vAcNSs with wild type baculoviruses clearly enhanced polyhedra production in all host cells. Confocal microscopy analysis showed that NSs accumulated in abundance in the cytoplasm of permissive and semipermissive cells. In contrast, high amounts of NSs were detected in the nuclei of nonpermissive cells. Co-infection of vAcNSs with a recombinant AcMNPV containing the enhanced green fluorescent protein (egfp) gene, significantly increased EGFP expression in semipermissive cells and in Anticarsia gemmatalis-hemocytes. Absence of small RNA molecules of egfp transcripts in this cell line and in a permissive cell line indicates the suppression of gene silencing activity. On the other hand, vAcNSs was not able to suppress RNAi in a nonpermissive cell line. Our data showed that NSs protein of TSWV facilitates baculovirus replication in different lepidopteran cell lines, and these results indicate that NSs could play a similar role during TSWV-infection in its thrips vector. Copyright © 2010 Elsevier B.V. All rights reserved.

  4. Theoretical calculation of solid particles deposition from the air

    Directory of Open Access Journals (Sweden)

    Bobro Milan

    2002-03-01

    Full Text Available This paper presents the calculation of harmful substance deposition (air pollution from the point source (Slanèo, et al., 2001 using equation (1. The point source shall be understood as e.g. chimneys of factory, heat plant, incinerator, boiler plant, local heating plant, etc.The theoretical calculation of concentration (1, or deposition (8 is based on the study of transfer and dispersion of pollution in air (Slanèo, et al., 2000a. The movement of pollution in air consists of a movement of the air itself and a relative movement of pollution particles and air, while the movement of harmful substance in the smoke trail is under the influence of turbulent diffusion, convection and gravitation. Molecular diffusion is not important in this process. When calculating concentrations (1 and deposition (8 of air pollution on a particular place near the source, it is assumed that the air speed is constant, the direction of wind does not change with the height and the source of air pollution is time-constant. The change in the wind speed with the height depends on the stability class of atmosphere (temperature gradient (Slanèo, et al., 2000a and it is calculated using equation (10.The theoretical calculation of concentration and or deposition of harmful substance from the point source (1 and (8 shall be applied if the harmful substance particles, which leave the source, have the same density (composition, shape (spherical and size.The experimental observations of dust deposition showed the significance of 0.1-20 µm particles. The application of equation (1 to calculate the concentration is conditioned, in addition to the recognition of source parameters and meteorological conditions, by the recognition of the particle sedimentation speed, which changes with the size of particle radius (2.For a practical calculation of deposition it is therefore necessary to know the differential distribution function f(r of particle radii, which can be made on the basis

  5. Lambda-guided calculation method (LGC method) for xenon/CT CBF

    Energy Technology Data Exchange (ETDEWEB)

    Sase, Shigeru [Anzai Medical Co., Ltd., Tokyo (Japan); Honda, Mitsuru; Kushida, Tsuyoshi; Seiki, Yoshikatsu; Machida, Keiichi; Shibata, Iekado [Toho Univ., Tokyo (Japan). School of Medicine

    2001-12-01

    A quantitative CBF calculation method for xenon/CT was developed by logically estimating time-course change rate (rate constant) of arterial xenon concentration from that of end-tidal xenon concentration. A single factor ({gamma}) was introduced to correlate the end-tidal rate constant (Ke) with the arterial rate constant (Ka) in a simplified equation. This factor ({gamma}) is thought to reflect the diffusing capacity of the lung for xenon. When an appropriate value is given to {gamma}, it is possible to calculate the arterial rate constant (Calculated Ka) from Ke. To determine {gamma} for each xenon/CT CBF examination, a procedure was established which utilizes the characteristics of white matter lambda; lambda refers to xenon brain-blood partition coefficient. Xenon/CT studies were performed on four healthy volunteers. Hemispheric CBF values (47.0{+-}9.0 ml/100 g/min) with use of Calculated Ka were close to the reported normative values. For a 27-year-old healthy man, the rate constant for the common carotid artery was successfully measured and nearly equal to Calculated Ka. The authors conclude the method proposed in this work, lambda-guided calculation method, could make xenon/CT CBF substantially reliable and quantitative by effective use of end-tidal xenon. (author)

  6. Lambda-guided calculation method (LGC method) for xenon/CT CBF

    International Nuclear Information System (INIS)

    Sase, Shigeru; Honda, Mitsuru; Kushida, Tsuyoshi; Seiki, Yoshikatsu; Machida, Keiichi; Shibata, Iekado

    2001-01-01

    A quantitative CBF calculation method for xenon/CT was developed by logically estimating time-course change rate (rate constant) of arterial xenon concentration from that of end-tidal xenon concentration. A single factor (γ) was introduced to correlate the end-tidal rate constant (Ke) with the arterial rate constant (Ka) in a simplified equation. This factor (γ) is thought to reflect the diffusing capacity of the lung for xenon. When an appropriate value is given to γ, it is possible to calculate the arterial rate constant (Calculated Ka) from Ke. To determine γ for each xenon/CT CBF examination, a procedure was established which utilizes the characteristics of white matter lambda; lambda refers to xenon brain-blood partition coefficient. Xenon/CT studies were performed on four healthy volunteers. Hemispheric CBF values (47.0±9.0 ml/100 g/min) with use of Calculated Ka were close to the reported normative values. For a 27-year-old healthy man, the rate constant for the common carotid artery was successfully measured and nearly equal to Calculated Ka. The authors conclude the method proposed in this work, lambda-guided calculation method, could make xenon/CT CBF substantially reliable and quantitative by effective use of end-tidal xenon. (author)

  7. Giving Ourselves Permission to Take Risks

    Science.gov (United States)

    Jones, Elizabeth

    2012-01-01

    What's a risk? It's when one doesn't know what will happen when she/he takes action. Risks can be little or big, calculated or stupid. Every new idea carries risks--and the challenge to face them and see what will happen. Nobody becomes smart, creative, self-confident, and respectful of others without taking risks--remaining open to possibilities…

  8. Determination of tritium concentrations in humans before the development of a nuclear power plant in Turkey.

    Science.gov (United States)

    Dizman, Serdar; Yilmaz, Adnan; Keser, Recep

    2015-01-01

    The most widely used method to determine the level of tritium in humans is testing urine. Tritium concentrations in urine samples of 100 persons aged 18-66 years selected randomly from a pilot region in Turkey were analysed. The average activity concentration of urine samples was 4.66 ± 1.94 Bq L(-1) and the maximum activity concentration was 27.91 Bq L(-1). The minimum detectable activity was 2.38 Bq L(-1). The annual effective dose from tritium was also evaluated on the basis of the measurement results and reference values recommended by the International Commission on Radiological Protection. The effective doses for males and females were 4.56 and 3.54 nSv, respectively. These results were lower than the permissible annual effective dose for members of the public.

  9. Radiocarbon concentration in modern tree rings from Valladolid, Spain

    International Nuclear Information System (INIS)

    Rakowski, Andrzej Z.; Nakamura, Toshio; Pazdur, Anna; Charro, Elena; Villanueva, Jose Luis Gutierrez; Piotrowska, Natalia

    2010-01-01

    New results of radiocarbon concentration in tree rings from the City of Valladolid (Spain) covering a growth period of 22 year have been measured using an AMS. Samples were taken using a hollow drill from a living tree, and α-cellulose was extracted from each of annual rings (early and late wood separately). The set of data shows lower radiocarbon concentration than that reported for 'clean air' at the reference station, indicating a remarkable input of 'dead' CO 2 of fossil fuel origin. Using data of carbon dioxide and 14 C concentrations from Schauinsland, the corresponding summer and winter values of the fossil component (c f ) in carbon dioxide were calculated for the City of Valladolid. By fitting exponential and linear functions to the experimental data, the exchange time was calculated, and the expected future 14 C concentration in the atmosphere was estimated.

  10. Monte-Carlo calculation of the calibration factors for the interfacial area concentration and the velocity of the bubbles for double sensor conductivity probe

    International Nuclear Information System (INIS)

    Munoz-Cobo, J.L.; Pena, J.; Chiva, S.; Mendez, S.

    2007-01-01

    This paper presents a study of the estimation of the correction factors for the interfacial area concentration and the bubble velocity in two phase flow measurements using the double sensor conductivity probe. Monte-Carlo calculations of these correction factors have been performed for different values of the relative distance (ΔS/D) between the tips of the conductivity probe and different values of the relative bubble velocity fluctuation parameter. Also this paper presents the Monte-Carlo calculation of the expected value of the calibration factors for bubbly flow assuming a log-normal distribution of the bubble sizes. We have computed the variation of the expected values of the calibration factors with the relative distance (ΔS/D) between the tips and the velocity fluctuation parameter. Finally, we have performed a sensitivity study of the variation of the average values of the calibration factors for bubbly flow with the geometrical standard deviation of the log-normal distribution of bubble sizes. The results of these calculations show that the total interfacial area correction factor is very close to 2, and depends very weakly on the velocity fluctuation, and the relative distance between tips. For the velocity calibration factor, the Monte-Carlo results show that for moderate values of the relative bubble velocity fluctuation parameter (H max ≤ 0.3) and values of the relative distance between tips not too small (ΔS/D ≥ 0.2), the correction velocity factor for the bubble sensor conductivity probe is close to unity, ranging from 0.96 to 1

  11. Simple Calculation Programs for Biology Immunological Methods

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Simple Calculation Programs for Biology Immunological Methods. Computation of Ab/Ag Concentration from EISA data. Graphical Method; Raghava et al., 1992, J. Immuno. Methods 153: 263. Determination of affinity of Monoclonal Antibody. Using non-competitive ...

  12. Behavior of water gel permissibles in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Ribovich, J.; Watson, R.W.

    1979-01-01

    This paper presents an overview of the successful use of water gel permissibles, since their introduction in 1970, with an emphasis on some problems of behavior in their field application. One is the metal clip or ties used to seal the water gel package. Miners are occasionally hit by the 2.4 mm metal wire expelled from boreholes in normal shooting operations. Manufacturers have consequently reduced the mass of the metal ties by 25-50%, providing a partial solution. Another problem concerned two reported instances of misfired water gel burning after coal shooting operations. Extensive tests have offered no satisfactory solution as yet, except to point up a principal shortcoming of water gels: that of pressure desensitization. Two other factors affecting sensitivity, and possibly resulting in misfires, are low temperature and aging. There is a decline in air-gap sensitivity with prolonged storage but all approved water gels seem capable of meeting requirements for long periods under normal storage conditions. Low temperature tests indicate the majority of water gels become insensitive to a No. 6 EBC at temperatures easily attained in cold weather storage. An attempt was made to determine the minimum temperature at which a nitroglycerin-sensitized permisslbe could be initiated with a No. 8 cap; a particularly granular one was initiated as low as minus 196 C. (5 refs.) (In English)

  13. Assessment of metal element concentrations in mussel (M. Galloprovincialis) in Eastern Black Sea, Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Cevik, U. [Karadeniz Technical University, Department of Physics, 61080 Trabzon (Turkey)], E-mail: berrenazli@yahoo.com; Damla, N.; Kobya, A.I. [Karadeniz Technical University, Department of Physics, 61080 Trabzon (Turkey); Bulut, V.N. [Giresun University, Department of Chemistry, 28049 Giresun (Turkey); Duran, C. [Karadeniz Technical University, Department of Chemistry, 61080 Trabzon (Turkey); Dalgic, G. [Rize University, Faculty of Fisheries, 53100 Rize (Turkey); Bozaci, R. [Karadeniz Technical University, Department of Physics, 61080 Trabzon (Turkey)

    2008-12-30

    The main goal of this work is to determine the effects of pollution of copper, lead and zinc mines on the Eastern Black Sea. Metal and heavy metal concentrations in the Eastern Black Sea mussels were measured using Energy Dispersive X-ray Fluorescence (EDXRF) and Flame Atomic Absorption Spectroscopy (FAAS). The analytical results showed that the tissue of mussel in Eastern Black Sea contains K, Ca, Fe, Cu, Zn, and Sr elements, and the shell of mussel contains Ca, Cu, Sr, and Ba elements. Due to the detection limit of EDXRF, the mussels were analyzed with FAAS for Cr, Mn, Ni, Cd and Pb elements. An ANOVA and Pearson correlation analyses were performed. The results showed although that the mean concentrations of Cu and Zn for the tissue of the mussels were markedly above the permissible levels of the Turkish regulations, Zn concentration is in the limits of the Food and Agriculture Organization (FAO)

  14. Determination, Source Identification and GIS Mapping for Nitrate Concentration in Groundwater from Bara Aquifer

    Energy Technology Data Exchange (ETDEWEB)

    Elami, G. M.; Sam, A. K.; Yagob, T. I.; Siddeeg, S. E.M.B.; Hatim, E.; Hajo, I. [Sudan Atomic Energy Commission, Sudan, Khartoum (Sudan)

    2013-07-15

    This study was carried out to determine the level of nitrate concentration in well water from Bara aquifer in north Kordofan state (west central sudan). The analysis was conducted for 69 wells from different villages within the Bara basin. Spectophotometric analysis was used to determine nitrate, nitrite and ammonia. Results revealed that nitrate concentration range was from 9.68 to 891 mg L in the sampled well with 81% exceeding the maximum permissible limits set for drinking water by WHO and SSMO. Animal waste and organic soil nitrogen were found to be the source of nitrate in these wells as indicated by {sup 15}N. The majority of wells with high nitrate are in the north and the north east part of the study area are shown by the GIS predictive map. (author)

  15. Permissible Home Range Estimation (PHRE in Restricted Habitats: A New Algorithm and an Evaluation for Sea Otters.

    Directory of Open Access Journals (Sweden)

    L Max Tarjan

    Full Text Available Parametric and nonparametric kernel methods dominate studies of animal home ranges and space use. Most existing methods are unable to incorporate information about the underlying physical environment, leading to poor performance in excluding areas that are not used. Using radio-telemetry data from sea otters, we developed and evaluated a new algorithm for estimating home ranges (hereafter Permissible Home Range Estimation, or "PHRE" that reflects habitat suitability. We began by transforming sighting locations into relevant landscape features (for sea otters, coastal position and distance from shore. Then, we generated a bivariate kernel probability density function in landscape space and back-transformed this to geographic space in order to define a permissible home range. Compared to two commonly used home range estimation methods, kernel densities and local convex hulls, PHRE better excluded unused areas and required a smaller sample size. Our PHRE method is applicable to species whose ranges are restricted by complex physical boundaries or environmental gradients and will improve understanding of habitat-use requirements and, ultimately, aid in conservation efforts.

  16. Concerning permission of commercial processing of nuclear fuel substances at Rokkasho plant of Japan Nuclear Fuel Industries, Ltd

    International Nuclear Information System (INIS)

    1988-01-01

    The Nuclear Safety Commission on Dec. 19, 1987 directed the Nuclear Fuel Safety Expert Group to carry out a study on it, made deliberations after receiving a report from the Group on July 13, 1988, and submitted the findings to the Prime Minister on July 21. The study and deliberations were intended to determine the conformity of the permission to the applicable criteria specified in laws relating to control of nuclear material, nuclear fuel and nuclear reactor. The investigation on the location covered the site conditions, meteorology, ground conditions, hydrology, seismic environments, and social environment. The investigations on the safety design addressed the anti-earthquake performance, fire/explosion prevention, criticality control, thermal stability, containment performance, safety against natural phenomena other than earthquake, radioactive waste management, and radiation control. Other investigations included exposure evaluation and accident analysis. It was concluded that the permission would not have adverse effects on the safety of the processing business. (Nogami, K.)

  17. Concerning permission of commercial processing of nuclear fuel substances at Rokkasho plant of Japan Nuclear Fuel Industries, Ltd

    Energy Technology Data Exchange (ETDEWEB)

    1988-12-01

    The Nuclear Safety Commission on Dec. 19, 1987 directed the Nuclear Fuel Safety Expert Group to carry out a study on it, made deliberations after receiving a report from the Group on July 13, 1988, and submitted the findings to the Prime Minister on July 21. The study and deliberations were intended to determine the conformity of the permission to the applicable criteria specified in laws relating to control of nuclear material, nuclear fuel and nuclear reactor. The investigation on the location covered the site conditions, meteorology, ground conditions, hydrology, seismic environments, and social environment. The investigations on the safety design addressed the anti-earthquake performance, fire/explosion prevention, criticality control, thermal stability, containment performance, safety against natural phenomena other than earthquake, radioactive waste management, and radiation control. Other investigations included exposure evaluation and accident analysis. It was concluded that the permission would not have adverse effects on the safety of the processing business. (Nogami, K.).

  18. Development of radiological concentrations and unit liter doses for TWRS FSAR radiological consequence calculations

    International Nuclear Information System (INIS)

    Cowley, W.L.

    1996-01-01

    The analysis described in this report develops the Unit Liter Doses for use in the TWRS FSAR. The Unit Liter Doses provide a practical way to calculate conservative radiological consequences for a variety of potential accidents for the tank farms

  19. The Effect of Indium Concentration on the Structure and Properties of Zirconium Based Intermetallics: First-Principles Calculations

    Directory of Open Access Journals (Sweden)

    Fuda Guo

    2016-01-01

    Full Text Available The phase stability, mechanical, electronic, and thermodynamic properties of In-Zr compounds have been explored using the first-principles calculation based on density functional theory (DFT. The calculated formation enthalpies show that these compounds are all thermodynamically stable. Information on electronic structure indicates that they possess metallic characteristics and there is a common hybridization between In-p and Zr-d states near the Fermi level. Elastic properties have been taken into consideration. The calculated results on the ratio of the bulk to shear modulus (B/G validate that InZr3 has the strongest deformation resistance. The increase of indium content results in the breakout of a linear decrease of the bulk modulus and Young’s modulus. The calculated theoretical hardness of α-In3Zr is higher than the other In-Zr compounds.

  20. Use of simple transport equations to estimate waste package performance requirements

    International Nuclear Information System (INIS)

    Wood, B.J.

    1982-01-01

    A method of developing waste package performance requirements for specific nuclides is described. The method is based on: Federal regulations concerning permissible concentrations in solution at the point of discharge to the accessible environment; a simple and conservative transport model; baseline and potential worst-case release scenarios. Use of the transport model enables calculation of maximum permissible release rates within a repository in basalt for each of the scenarios. The maximum permissible release rates correspond to performance requirements for the engineered barrier system. The repository was assumed to be constructed in a basalt layer. For the cases considered, including a well drilled into an aquifer 1750 m from the repository center, little significant advantage is obtained from a 1000-yr as opposed to a 100-yr waste package. A 1000-yr waste package is of importance only for nuclides with half-lives much less than 100 yr which travel to the accessible environment in much less than 1000 yr. Such short travel times are extremely unlikely for a mined repository. Among the actinides, the most stringent maximum permissible release rates are for 236 U and 234 U. A simple solubility calculation suggests, however, that these performance requirements can be readily met by the engineered barrier system. Under the reducing conditions likely to occur in a repository located in basalt, uranium would be sufficiently insoluble that no solution could contain more than about 0.01% of the maximum permissible concentration at saturation. The performance requirements derived from the one-dimensional modeling approach are conservative by at least one to two orders of magnitude. More quantitative three-dimensional modeling at specific sites should enable relaxation of the performance criteria derived in this study. 12 references, 8 figures, 8 tables

  1. Concentration Of 228Th, 226Ra, And 40K Radionuclides In Drinking Water In Southern Sumatera

    International Nuclear Information System (INIS)

    Sutarman; Warsono, Asep; Wahyudi

    2000-01-01

    Measurements of 228 Th, 226 Ra, and 40 K concentrations in drinking water on several places in Southern Sumatera (1997-1999) have been carried out. The sample were collected from the Province of Lampung (Kalianda, Bandar Lampung, Kotabumi, Talangpadang, Kotaagung, Liwa, Manggala, and Pakuanratu), and the Province of Southern Sumatera (Palembang-1, Palembang-2, Plaju, Lahat, and Sekayu). Measurements of 228 Th, 226 Ra, and 40 K concentrations in drinking water using the gamma spectrometer with the HP-Ge detector. The results of measurement showed that the concentration was the range of undetectable ( 228 Th concentration, the range of undetectable ( 226 Ra, radionuclide and the range of undetectable (< 128.96 mBq/l) to (880.54 n 22.75) mBq/l with average of (412.12 n 5.02) mBq/l, and the data mentioned above were still far under the maximum permissible concentration. The estimated of annual dose equivalent effective in drinking water was 0.03 mSv/year for public (5 mSv/year)

  2. Block Tridiagonal Matrices in Electronic Structure Calculations

    DEFF Research Database (Denmark)

    Petersen, Dan Erik

    in the Landauer–Büttiker ballistic transport regime. These calculations concentrate on determining the so– called Green’s function matrix, or portions thereof, which is the inverse of a block tridiagonal general complex matrix. To this end, a sequential algorithm based on Gaussian elimination named Sweeps...

  3. Aerosol deposition velocities on the Pacific and Atlantic oceans calculated from 7Be measurements

    International Nuclear Information System (INIS)

    Young, J.A.; Silker, W.B.

    1979-01-01

    The concentrations of 7 Be were measured in Pacific and Atlantic ocean water for past several years to determine the deposition velocity of aerosol particles on the ocean surface. Beryllium-7 is produced at a relatively constant rate in the atmosphere by spallation reactions of cosmic rays with atmospheric nitrogen and oxygen. Immediately after its formation 7 Be becomes attached to aerosol particles, and therefore can serve as tracers of the subsequent behavior of these particles. Isopleths of 7 Be surface water concentration, 7 Be inventory in the ocean, and deposition velocity have been prepared for the Pacific Ocean from 30 0 S to 60 0 N and for the Atlantic Ocean from 10 0 N to 55 0 N. The concentrations, inventories and deposition velocities tended to be higher in regions where precipitation was high, and generally increased with latitude. The average flux of 7 Be across the ocean surface was calculated to be 0.027 atoms cm -2 sec -1 which is probably not significantly greater than the worldwide average 7 Be flux across land and ocean surfaces of 0.022 atoms cm -2 sec -1 calculated by Lal and Peters. The average deposition velocity was calculated to be 0.80 cm sec -1 . This value may be 10 to 30% too low, since it was calculated using atmospheric 7 Be concentrations which were measured at continental stations. Measurements of atmospheric 7 Be concentrations at ocean stations suggest that the concentrations at the continental stations averaged 10 to 30% higher than the concentrations over the ocean

  4. Aerosol deposition velocities on the Pacific and Atlantic oceans calculated from 7Be measurements

    International Nuclear Information System (INIS)

    Young, J.A.; Silker, W.B.

    1980-01-01

    The concentrations of 7 Be have been measured in Pacific and Atlantic ocean water for the past several years to determine the deposition velocity of aerosol particles on the ocean surface. 7 Be is produced at a relatively constant rate in the atmosphere by spallation reactions of cosmic rays with atmospheric nitrogen and oxygen. Immediately after its formation 7 Be becomes attached to aerosol particles, and therefore can serve as tracers of the subsequent behavior of these particles. Isopleths of 7 Be surface water concentrations, 7 Be inventory in the ocean, and deposition velocity have been prepared for the Pacific Ocean from 30 0 S to 60 0 N and for the Atlantic Ocean from 10 0 N to 55 0 N. The concentrations, inventories and deposition velocities tended to be higher in regions where precipitation was high, and generally increased with latitude. The average flux of 7 Be across the ocean surface was calculated to be 0.027 atoms cm -2 s -1 which is probably not significantly greater than the worldwide average 7 Be flux across land and ocean surfaces of 0.022 atoms cm -2 s -1 calculated by Lal and Peters. The average deposition velocity was calculated to be 0.80 cm s -1 . This value may be 10-50% too low, since it was calculated using atmospheric 7 Be concentrations which were measured at continental stations. Measurements of atmospheric 7 Be concentrations at ocean stations suggest that the concentrations at the continental stations averaged 10-50% higher than the concentrations over the ocean. (orig.)

  5. Study of a Greek area with enhanced indoor radon concentrations

    International Nuclear Information System (INIS)

    Louizi, A.; Nikolopoulos, D.; Koukouliou, V.; Kehagia, K.

    2003-01-01

    In this paper the focus is on Arnea Chalkidikis, an area in Greece with granitic geological background and indications of possible elevated radon concentration indoors. Data are reported of indoor radon measurements with etched track detectors and those used for dosimetric estimations. Moreover, data are reported on soil gas and soil radon concentrations in Arnea, as well as radon and uranium concentrations in water samples. From the measured radon concentrations in water samples the contribution to the overall dose has been calculated. For a period of 1 month, indoor radon and progeny activity has also been monitored in the dwelling that has the maximum indoor radon concentration in Greece. This dwelling is in Arnea and the dose delivered to the inhabitants has been calculated. Mean annual effective dose due to indoor radon was 4.5 mSv and about 11% of this was due to the use of water. Mean soil gas concentration and soil radon concentration were (90 ± 30) kBq m -3 (P -3 (P -1 (P<0.05). (author)

  6. Vectorization of nuclear codes for atmospheric transport and exposure calculation of radioactive materials

    International Nuclear Information System (INIS)

    Asai, Kiyoshi; Shinozawa, Naohisa; Ishikawa, Hirohiko; Chino, Masamichi; Hayashi, Takashi

    1983-02-01

    Three computer codes MATHEW, ADPIC of LLNL and GAMPUL of JAERI for prediction of wind field, concentration and external exposure rate of airborne radioactive materials are vectorized and the results are presented. Using the continuous equation of incompressible flow as a constraint, the MATHEW calculates the three dimensional wind field by a variational method. Using the particle-in -cell method, the ADPIC calculates the advection and diffusion of radioactive materials in three dimensional wind field and terrain, and gives the concentration of the materials in each cell of the domain. The GAMPUL calculates the external exposure rate assuming Gaussian plume type distribution of concentration. The vectorized code MATHEW attained 7.8 times speedup by a vector processor FACOM230-75 APU. The ADPIC and GAMPUL are estimated to attain 1.5 and 4 times speedup respectively on CRAY-1 type vector processor. (author)

  7. A new approach for soil-plant transfer calculations

    International Nuclear Information System (INIS)

    Dorp, F. van; Eleveld, R.; Frissel, M.J.

    1979-01-01

    Models to calculate radiation doses to man caused by normal or accidental release of radionuclides from nuclear industries often include the transfer of these nuclides from soil to plant. This soil-plant transfer is mostly described with a black box approach by using concentration factors. This approach has several disadvantages, the most important being the lack of physical meaning of a concentration factor. We propose to describe the soil-plant transfer of radionuclides as a function of plant and soil parameters all having a physical meaning. The separate parameters are open to experimental determination but a realistic estimation of the parameters is also possible, or the use of a combination of both. Depending on the purpose of the calculation, realistic or conservative values of the parameters can be used and the degree of conservatism can be indicated. (author)

  8. Arsenic health risk assessment in drinking water and source apportionment using multivariate statistical techniques in Kohistan region, northern Pakistan.

    Science.gov (United States)

    Muhammad, Said; Tahir Shah, M; Khan, Sardar

    2010-10-01

    The present study was conducted in Kohistan region, where mafic and ultramafic rocks (Kohistan island arc and Indus suture zone) and metasedimentary rocks (Indian plate) are exposed. Water samples were collected from the springs, streams and Indus river and analyzed for physical parameters, anions, cations and arsenic (As(3+), As(5+) and arsenic total). The water quality in Kohistan region was evaluated by comparing the physio-chemical parameters with permissible limits set by Pakistan environmental protection agency and world health organization. Most of the studied parameters were found within their respective permissible limits. However in some samples, the iron and arsenic concentrations exceeded their permissible limits. For health risk assessment of arsenic, the average daily dose, hazards quotient (HQ) and cancer risk were calculated by using statistical formulas. The values of HQ were found >1 in the samples collected from Jabba, Dubair, while HQ values were pollution load was also calculated by using multivariate statistical techniques like one-way ANOVA, correlation analysis, regression analysis, cluster analysis and principle component analysis. Copyright © 2010 Elsevier Ltd. All rights reserved.

  9. Generation of input parameters for OSPM calculations. Sensitivity analysis of a method based on a questionnaire

    Energy Technology Data Exchange (ETDEWEB)

    Vignati, E.; Hertel, O.; Berkowicz, R. [National Environmental Research Inst., Dept. of Atmospheric Enviroment (Denmark); Raaschou-Nielsen, O. [Danish Cancer Society, Division of Cancer Epidemiology (Denmark)

    1997-05-01

    The method for generation of the input data for the calculations with OSPM is presented in this report. The described method which is based on information provided from a questionnaire, will be used for model calculations of long term exposure for a large number of children in connection with an epidemiological study. A test of the calculation method has been performed on a few locations in which detailed measurements of air pollution, meteorological data and traffic were available. Comparisons between measured and calculated concentrations were made for hourly, monthly and yearly values. Beside the measured concentrations, the test results were compared to results obtained with the optimal street configuration data and measured traffic. The main conclusions drawn from this investigation are: (1) The calculation method works satisfactory well for long term averages, whereas the uncertainties are high when short term averages are considered. (2) The street width is one of the most crucial input parameters for the calculation of street pollution levels for both short and long term averages. Using H.C. Andersens Boulevard as an example, it was shown that estimation of street width based on traffic amount can lead to large overestimation of the concentration levels (in this case 50% for NO{sub x} and 30% for NO{sub 2}). (3) The street orientation and geometry is important for prediction of short term concentrations but this importance diminished for longer term averages. (4) The uncertainties in diurnal traffic profiles can influence the accuracy of short term averages, but are less important for long term averages. The correlation is good between modelled and measured concentrations when the actual background concentrations are replaced with the generated values. Even though extreme situations are difficult to reproduce with this method, the comparison between the yearly averaged modelled and measured concentrations is very good. (LN) 20 refs.

  10. Volcanic ash dosage calculator: A proof-of-concept tool to support aviation stakeholders during ash events

    Science.gov (United States)

    Dacre, H.; Prata, A.; Shine, K. P.; Irvine, E.

    2017-12-01

    The volcanic ash clouds produced by Icelandic volcano Eyjafjallajökull in April/May 2010 resulted in `no fly zones' which paralysed European aircraft activity and cost the airline industry an estimated £1.1 billion. In response to the crisis, the Civil Aviation Authority (CAA), in collaboration with Rolls Royce, produced the `safe-to-fly' chart. As ash concentrations are the primary output of dispersion model forecasts, the chart was designed to illustrate how engine damage progresses as a function of ash concentration. Concentration thresholds were subsequently derived based on previous ash encounters. Research scientists and aircraft manufactures have since recognised the importance of volcanic ash dosages; the accumulated concentration over time. Dosages are an improvement to concentrations as they can be used to identify pernicious situations where ash concentrations are acceptably low but the exposure time is long enough to cause damage to aircraft engines. Here we present a proof-of-concept volcanic ash dosage calculator; an innovative, web-based research tool, developed in close collaboration with operators and regulators, which utilises interactive data visualisation to communicate the uncertainty inherent in dispersion model simulations and subsequent dosage calculations. To calculate dosages, we use NAME (Numerical Atmospheric-dispersion Modelling Environment) to simulate several Icelandic eruption scenarios, which result in tephra dispersal across the North Atlantic, UK and Europe. Ash encounters are simulated based on flight-optimal routes derived from aircraft routing software. Key outputs of the calculator include: the along-flight dosage, exposure time and peak concentration. The design of the tool allows users to explore the key areas of uncertainty in the dosage calculation and to visualise how this changes as the planned flight path is varied. We expect that this research will result in better informed decisions from key stakeholders during

  11. Maximum permissible concentrations and negligible concentrations for antifouling substances. Irgarol 1051, dichlofluanid, ziram, chlorothalonil and TCMTB

    NARCIS (Netherlands)

    Wezel AP van; Vlaardingen P van; CSR

    2001-01-01

    In dit rapport zijn maximaal toelaatbare concentratie's en verwaarloosbare concentratie's afgeleid voor diverse aangroeiwerende middelen, welke worden gebruikt als vervanger voor TBT zoals Irgarol 1051, dichlofluanide, ziram, chloorthalonil en TCMTB.

  12. Estimation of maximum credible atmospheric radioactivity concentrations and dose rates from nuclear tests

    International Nuclear Information System (INIS)

    Telegadas, K.

    1979-01-01

    A simple technique is presented for estimating maximum credible gross beta air concentrations from nuclear detonations in the atmosphere, based on aircraft sampling of radioactivity following each Chinese nuclear test from 1964 to 1976. The calculated concentration is a function of the total yield and fission yield, initial vertical radioactivity distribution, time after detonation, and rate of horizontal spread of the debris with time. calculated maximum credible concentrations are compared with the highest concentrations measured during aircraft sampling. The technique provides a reasonable estimate of maximum air concentrations from 1 to 10 days after a detonation. An estimate of the whole-body external gamma dose rate corresponding to the maximum credible gross beta concentration is also given. (author)

  13. The Impact of Different Permissible Exposure Limits on Hearing Threshold Levels Beyond 25 dBA

    OpenAIRE

    Sayapathi, Balachandar S; Su, Anselm Ting; Koh, David

    2014-01-01

    Background: Development of noise-induced hearing loss is reliant on a few factors such as frequency, intensity, and duration of noise exposure. The occurrence of this occupational malady has doubled from 120 million to 250 million in a decade. Countries such as Malaysia, India, and the US have adopted 90 dBA as the permissible exposure limit. According to the US Occupational Safety and Health Administration (OSHA), the exposure limit for noise is 90 dBA, while that of the US National Institut...

  14. Endogenous hormone concentrations correlate with fructan metabolism throughout the phenological cycle in Chrysolaena obovata.

    Science.gov (United States)

    Rigui, Athos Poli; Gaspar, Marília; Oliveira, Vanessa F; Purgatto, Eduardo; Carvalho, Maria Angela Machado de

    2015-06-01

    that fructan metabolism correlates well with endogenous hormone concentrations and environmental changes, suggesting that the co-ordinated action of carbohydrate metabolism and hormone synthesis enables C. obovata to survive unfavourable field conditions. Endogenous hormone concentrations seem to be related to regulation of fructan metabolism and to the transition between phenophases, signalling for energy storage, reserve mobilization and accumulation of oligosaccharides as osmolytes. © The Author 2015. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  15. Metals concentrations in sediments and oyster Crassostrea gigas from La Pitahaya lagoon, Sinaloa, NW Mexico

    Science.gov (United States)

    Luna Varela, R.; Muñoz Sevilla, N.; Campos Villegas, L.; Rodriguez Espinosa, P.; Gongora Gomez, A.; MP, J.

    2013-05-01

    This present study was performed in a culture of Crassostrea gigas in La Pitahaya, Sinaloa, México. The main objective is to identify the enrichment pattern of trace elements (Cu, Cd, Cr, Ni, Pb, Zn, Hg, As, V) also was determine concentrations thereof in oyster. Four sampling sites were selected, two smaller channels which connect the lagoon directly , the region of culture and connection with the sea ; and each sampling consisted of 4 sample sediments and 50 oysters of commercial size per mounth . Concentrations of trace metals were determined using atomic absorption spectrophotometry (AAS). The higher concentration of elements in certain samples clearly suggests that they are directly fed by the smaller channels which connect the lagoon directly. These small channels often carry the contaminants which are absorbed and deposited in the sediments. The results were also compared with the Effect Range Low (ERL) and Effect Range Medium (ERM) of NOAA and it indicates that Ni is above the ERL values. Cadmium, lead, chrome and copper concentrations exceeded the limits permissible of bivalbe mollusks established by the sanitary regulations

  16. Calculation of Si(Li) x-ray detector efficiencies

    International Nuclear Information System (INIS)

    Zaluzec, N.; Holton, R.

    1984-01-01

    The calculation of detector efficiency functions is an important step in the quantitative analysis of x-ray spectra when approached by a standardless technique. In this regard, it becomes essential that the analyst not only model the physical aspects of the absorption and transmission of the various windows present, but also use the most accurate data available for the mass absorption coefficients required in these calculations. The topic of modeling the size and shape of the windows present is beyond the scope of this paper and the authors instead concentrate on the mass absorption coefficients used in the calculations and their implications to efficiency calculations. For the purposes of this paper, the authors consider that the relative detector efficiency function of a conventional Si(Li) detector can be modeled by a simple expression

  17. Systems Biology Reveals Cigarette Smoke-Induced Concentration-Dependent Direct and Indirect Mechanisms That Promote Monocyte-Endothelial Cell Adhesion.

    Science.gov (United States)

    Poussin, Carine; Laurent, Alexandra; Peitsch, Manuel C; Hoeng, Julia; De Leon, Hector

    2015-10-01

    Cigarette smoke (CS) affects the adhesion of monocytes to endothelial cells, a critical step in atherogenesis. Using an in vitro adhesion assay together with innovative computational systems biology approaches to analyze omics data, our study aimed at investigating CS-induced mechanisms by which monocyte-endothelial cell adhesion is promoted. Primary human coronary artery endothelial cells (HCAECs) were treated for 4 h with (1) conditioned media of human monocytic Mono Mac-6 (MM6) cells preincubated with low or high concentrations of aqueous CS extract (sbPBS) from reference cigarette 3R4F for 2 h (indirect treatment, I), (2) unconditioned media similarly prepared without MM6 cells (direct treatment, D), or (3) freshly generated sbPBS (fresh direct treatment, FD). sbPBS promoted MM6 cells-HCAECs adhesion following I and FD, but not D. In I, the effect was mediated at a low concentration through activation of vascular inflammation processes promoted in HCAECs by a paracrine effect of the soluble mediators secreted by sbPBS-treated MM6 cells. Tumor necrosis factor α (TNFα), a major inducer, was actually shed by unstable CS compound-activated TNFα-converting enzyme. In FD, the effect was triggered at a high concentration that also induced some toxicity. This effect was mediated through an yet unknown mechanism associated with a stress damage response promoted in HCAECs by unstable CS compounds present in freshly generated sbPBS, which had decayed in D unconditioned media. Aqueous CS extract directly and indirectly promotes monocytic cell-endothelial cell adhesion in vitro via distinct concentration-dependent mechanisms. © The Author 2015. Published by Oxford University Press on behalf of the Society of Toxicology. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  18. eQuilibrator--the biochemical thermodynamics calculator.

    Science.gov (United States)

    Flamholz, Avi; Noor, Elad; Bar-Even, Arren; Milo, Ron

    2012-01-01

    The laws of thermodynamics constrain the action of biochemical systems. However, thermodynamic data on biochemical compounds can be difficult to find and is cumbersome to perform calculations with manually. Even simple thermodynamic questions like 'how much Gibbs energy is released by ATP hydrolysis at pH 5?' are complicated excessively by the search for accurate data. To address this problem, eQuilibrator couples a comprehensive and accurate database of thermodynamic properties of biochemical compounds and reactions with a simple and powerful online search and calculation interface. The web interface to eQuilibrator (http://equilibrator.weizmann.ac.il) enables easy calculation of Gibbs energies of compounds and reactions given arbitrary pH, ionic strength and metabolite concentrations. The eQuilibrator code is open-source and all thermodynamic source data are freely downloadable in standard formats. Here we describe the database characteristics and implementation and demonstrate its use.

  19. eQuilibrator—the biochemical thermodynamics calculator

    Science.gov (United States)

    Flamholz, Avi; Noor, Elad; Bar-Even, Arren; Milo, Ron

    2012-01-01

    The laws of thermodynamics constrain the action of biochemical systems. However, thermodynamic data on biochemical compounds can be difficult to find and is cumbersome to perform calculations with manually. Even simple thermodynamic questions like ‘how much Gibbs energy is released by ATP hydrolysis at pH 5?’ are complicated excessively by the search for accurate data. To address this problem, eQuilibrator couples a comprehensive and accurate database of thermodynamic properties of biochemical compounds and reactions with a simple and powerful online search and calculation interface. The web interface to eQuilibrator (http://equilibrator.weizmann.ac.il) enables easy calculation of Gibbs energies of compounds and reactions given arbitrary pH, ionic strength and metabolite concentrations. The eQuilibrator code is open-source and all thermodynamic source data are freely downloadable in standard formats. Here we describe the database characteristics and implementation and demonstrate its use. PMID:22064852

  20. Seasonal Composite Chlorophyll Concentrations - Gulf of Maine

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This personal geodatabase contains raster images of chlorophyll concentrations in the Gulf of Maine. These raster images are seasonal composites, and were calculated...

  1. Monthly Composite Chlorophyll Concentrations - Gulf of Maine

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This personal geodatabase contains raster images of chlorophyll concentrations in the Gulf of Maine. These raster images are monthly composites, and were calculated...

  2. DASH-FP, Multicomponent Time-Dependent Concentration Diffusion

    International Nuclear Information System (INIS)

    Apperson, C.E. Jr.; Carruthers, L.M.; Shinn, J.F.; Lee, C.E.

    1995-01-01

    1 - Description of program or function: The program DASH-FP calculates the transient concentration of multiple diffusing species with radioactive decay. 2 - Method of solution: Uses finite difference and exponential operator techniques

  3. Determination of Heavy elements in Drinking Water from Different Regions of Baghdad City (Iraq Using EDXRF Spectrometer

    Directory of Open Access Journals (Sweden)

    Muhanad H. Alrakabi

    2017-11-01

    Full Text Available It was calculated the average concentrations of elements manganese, iron, cobalt, nickel, copper, zinc, arsenic, cadmium and lead in the sixteen samples of drinking water (tap water, were collected from different areas in the Baghdad city. The Results indicated that the average of concentrations of the elements Mn, Fe, Pb, Ni and Cd (0.44ppm, 0.49ppm, 0.04ppm, 0.17ppm and 1.2ppm respectively higher than permissible limit while the concentrations of elements Cu and Zn (0.11ppm and 0.14ppm respectively were lower than the permissible limit of World Health Organization (WHO standards (1ppm and 3ppm respectively for drinking water and the concentration of Arsenic in the nuclear lab sample in college of sciences - Mustansiriyah University was higher than permissible limit. All the drinking water samples were analyzed and determined the physical and chemical properties such as Electrical Conductivity (EC, pH, and Total Dissolved Solids (TDS. The highest value was (1064μS/cm in Al-Tuwaitha sample and the lowest value (531μS/cm in Al-Sadr City (Sector 7 sample for the Electrical Conductivity. The pH values ranged from (7.0-8.2. The average levels of Total Dissolved Solids (TDS, the highest value was 550 mg/L in the Diyala Bridge sample while the lowest value 276mg/L in Al-Sadr City (Sector 7 sample. The results were compared with national and international standards, and it’s also showed that the values of the parameters within the permissible limit of World Health Organization (WHO standards, except the Electrical Conductivity values for some samples were higher than permissible limit. According to these results, all the water projects must be monitored as well as using the proper and modern techniques for treatment the drinking water.

  4. Theoretical calculations of the surface tension of Ag(1-x)-Cu(x) liquid alloys

    International Nuclear Information System (INIS)

    Aqra, Fathi; Ayyad, Ahmed

    2011-01-01

    Highlights: → A thermodynamic model for calculating the surface tension, and its temperature and composition dependences, of liquid binary alloys is described. → The model does not require the prior knowledge of the surface concentration and Gibbs energy. → The surface tension of the liquid Ag-Cu binary alloys has been calculated as a function of temperature and concentration. → The calculated values agree well with existing experimental data. - Abstract: The surface tension of silver-copper binary liquid alloys is calculated, in the frame work of Eyring theory. The calculations were made for different compositions (mole fraction, x Cu = 0, 0.2, 0.4, 0.6, 0.8 and 1), in the temperature range 1100-1800 K. The surface tension decreases with temperature increase, at a fixed copper fraction x Cu , and increases with increasing copper content. The calculated results are appropriately compared with existing literature data.

  5. Study of multiplication factor sensitivity to the spread of WWER spent fuel isotopics calculated by different codes

    International Nuclear Information System (INIS)

    Markova, L.

    2001-01-01

    As a sensitivity study the impact on the system reactivity was studied in the case that different calculational methodologies of spent fuel isotopic concentrations were used for WWER spent fuel inventory computations. The sets of isotopic concentrations obtained by calculations with different codes and libraries as a result of the CB2 international benchmark focused on WWER-440 burnup credit were used to show the spread of the calculated spent fuel system reactivity. Using the MCNP 4B code and changing the isotopics input data, the multiplication factor of an infinite array of the WWER-440 fuel pin cells was calculated. The evaluation of the results shows the sensitivity of the calculated reactivity to different calculational methodologies used for the spent fuel inventory computation. In the studied cases of the CB2 benchmark, the spread of the reference k-results relative to the mean was found less or about ±1% in spite of the fact that the data of isotopic concentrations were spread much more. (author)

  6. Atazanavir intracellular concentrations remain stable during pregnancy in HIV-infected patients.

    Science.gov (United States)

    Focà, Emanuele; Calcagno, Andrea; Bonito, Andrea; Simiele, Marco; Domenighini, Elisabetta; D'Avolio, Antonio; Quiros Roldan, Eugenia; Trentini, Laura; Casari, Salvatore; Di Perri, Giovanni; Castelli, Francesco; Bonora, Stefano

    2017-11-01

    Atazanavir (300 mg) boosted by ritonavir (100 mg) is the preferred third drug in pregnancy. However, there is still discordance on atazanavir dose increase during the third trimester. To evaluate plasma and intracellular atazanavir and ritonavir concentrations in HIV-infected women during pregnancy and after delivery. This was an observational study. HIV-infected pregnant patients treated with atazanavir/ritonavir plus either tenofovir/emtricitabine or abacavir/lamivudine had been prospectively enrolled after having signed a written informed consent form. Plasma and intracellular atazanavir and ritonavir Ctrough (24 ± 3 h after drug intake) were measured at each visit during the first, second and third trimesters and post-partum using validated HPLC-MS and HPLC-photodiode array methods (with direct evaluation of cellular volume). Data are described as median (IQR) and compared through non-parametric tests. Twenty-five patients were enrolled; at baseline, the median age was 32 years (27-35). All patients had plasma HIV RNA  0.05). This is the first demonstration that intracellular atazanavir exposure remains unchanged during pregnancy supporting the standard 300/100 mg atazanavir/ritonavir dosing throughout pregnancy. © The Author 2017. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  7. Initial stage of transformation of permissive cells by simian virus 40: development of resistance to productive infection.

    Science.gov (United States)

    Hahn, E C; Sauer, G

    1971-07-01

    A quantitative assay has been used to determine the conditions leading to acquisition of resistance of permissive cells to lytic infection. The number of cell colonies surviving infection depends on the occurrence of several cell divisions after infection. High yields of resistant colonies were obtained when infected, confluent cultures were released from contact inhibition 10 to 14 hr after infection. Infection of actively growing cells produced similar results, but halting further division by seeding these growing cells on confluent monolayers prevented the development of colonies. Colony formation was a direct function of multiplicities lower than 5. An inverse killing response was observed with higher multiplicities, yet colonies were produced at a multiplicity of infection as high as 50. Brief exposure of input simian virus 40 to ultraviolet light stimulated colony formation. Irradiation of the virus for longer periods of time led to reduction of colony formation at a rate slower than the rate of inactivation of viral infectivity. It was concluded that resistance is induced by simian virus 40 and that this alteration represents one of the earliest detectable characteristics of the transformation of permissive cells.

  8. Calculation of the uptake of CO into the human blood

    Energy Technology Data Exchange (ETDEWEB)

    Zankl, J.G.

    1981-01-01

    CO is a toxic substance mainly because, due to its high hemoglobin affinity, it inhibits oxygen transport in the human blood. This process must be quantified in order to establish limiting CO concentrations for garages, road tunnels, places of work, and for purpose of accident analysis. The medical information given is based on literature and is considered only as an introduction for non-experts. The emphasis of the work was on the development of a computer program by which the influence also of variable air CO concentrations and sea levels can be calculated. The program is available at the author's institute along with detailed calculations and results not considered in this publication.

  9. Blood-pressure-independent wall thickening of intramyocardial arterioles in experimental uraemia: evidence for a permissive action of PTH.

    Science.gov (United States)

    Amann, K; Törnig, J; Flechtenmacher, C; Nabokov, A; Mall, G; Ritz, E

    1995-11-01

    Abnormalities in cardiovascular structures, e.g. LV hypertrophy and thickening of vessels (arteries, arterioles, veins) are hallmarks of renal failure. They are in part independent of elevated blood pressure. Parathyroid hormone (PTH) has been shown to affect cardiac function and has also been identified as a permissive factor in the genesis of cardiac fibrosis. The present study in rats with experimental renal failure was designed to examine whether PTH was permissive for wall thickening of intramyocardial arterioles as well. Male SD rats were sham operated or subtotally nephrectomized and maintained for 2 weeks. Subgroups of subtotally nephrectomized (SNX) rats were parathyroidectomized (PTX). Saline or rat 1, 34 PTH was administered by osmotic minipump. Eucalcaemia was maintained in PTX animals by a high-calcium diet (3%). Serum calcium was not statistically different between the groups. After perfusion fixation, intramyocardial arterioles were assessed using stereological techniques (wall thickness; wall/lumen ratio; minimal lumen diameter; length density). In random samples of the left ventricle, wall thickness of arterioles was 2.2 +/- 0.25 microns in sham-op controls and 2.76 +/- 0.41 in SNX (n = at least 8 animals per group). SNX-PTX animals+solvent did not differ significantly from sham-op controls (2.08 +/- 0.42 microns), while SNX-PTX animals+PTH had values not significantly different from SNX (2.59 +/- 0.54 microns). Differences in wall thickness were not paralleled by differences in systolic blood pressure (sham-op 110 +/- 13.3 mmHg; SNX 138 +/- 8.4 mmHg, SNX-PTX+solvent 142 +/- 5.2 mmHg; SNX-PTX+PTH 148 +/- 5.7 mmHg). PTH treated animals showed signs of marked vascular smooth-muscle cell and endothelial-cell activation. The data suggest that wall thickening of intramyocardial arterioles in short-term experimental uraemia is dependent upon the presence of PTH (permissive effect).

  10. Equation for calculation of nitrogen solubility in iron alloys

    International Nuclear Information System (INIS)

    Pomarin, Yu.M.; Grigorenko, G.M.

    1989-01-01

    Equation for calculating nitrogen solubility in multicomponent iron melts in a wide range of partial pressures (1-1600 kPa), of doping component concentrations and temperatures (1773-2373 K) is proposed. Comparative analysis of experimental and calculated values of nitrogen solubility has demonstrated a principle possibility of applying the equation proposed for evaluating absorption ability to nitrogen of industrial nitrogen containing steels and ferroalloys subjected to melting or remelting in plasma or other melting devices

  11. Calculating Liquid Capacity to Understand what could have been Consumed from 'Drinking' Vessels

    Directory of Open Access Journals (Sweden)

    William Baddiley

    2018-05-01

    Full Text Available All Usk ware vessel form types used in the analyses in this article, with calculation areas indicated. Drawings by W. Baddiley, adapted from Greene (1993, 12-15 and reproduced with permission from Greene. There are many examples of vessel types reportedly used for drinking during the Roman period, but there have been few attempts to calculate the volume of liquid that such vessels could have held. For this article scaled reproductions of vessels from archaeological reports are used as the basis for calculating vessel capacity by applying the formula for the volume of a cylinder V equals Pi r squared h to calculate vessel volume and thus liquid capacity. Most of the vessels examined in this article consist of coarse ware and fineware pottery from the legionary fortress at Usk. The drinking silverware from the House of the Menander at Pompeii provides a comparison with the Usk pottery. The calculated capacities potentially allow distinctions between individual and communal drinking to be seen, while large variations in capacity are apparent even within supposedly tightly grouped datasets like the Drag. 27 samian ware from Usk. Comparing the capacities of different vessel types and vessel materials can also demonstrate a certain level of consumer preference. This is especially so at Usk where no vessels with a capacity of between 400ml and 500ml are found, and the majority of the vessels tend to cluster below 300ml. Identifying a specific drink being consumed from these vessels is more problematic, but by combining capacity data with other sources of evidence, such as find spots, vessel forms and materials, a number of possibilities are raised.

  12. Evaluation of physiological parameters and their influence on doses calculated from two alternative dosimetric models for the gastrointestinal tract

    International Nuclear Information System (INIS)

    Lessard, E.T.; Skrable, K.W.

    1981-01-01

    Two dosimetric models, the catenary compartmental model and the slug flow model are examined using three sets of physiological parameters. The impact of physiological parameters on the dosimetry of the tract is illustrated by comparing calculated maximum permissible daily activity ingestion rates for single, unabsorbed, particle emitting radionuclides with an effective energy term of unity. The conclusions drawn from this intercomparison of six different cases are: (1) Current dosimetric models which use physiological parameters described in this article do not significantly disagree, and (2) For the determination of average dose equivalent rates to segments of the tract due to chronic, long term ingestion of any radionuclide, the catenary compartmental model is a mathematically simpler approach. The catenary model in addition has certain advantages for the calculation of the photon dose contribution to one segment from cumulated activity (disintegrations) in another segment

  13. Reference Monte Carlo calculations of Maria reactor core

    International Nuclear Information System (INIS)

    Andrzejewski, K.; Kulikowska, T.

    2002-01-01

    The reference Monte Carlo calculations of MARIA reactor core have been carried to evaluate accuracy of the calculations at each stage of its neutron-physics analysis using deterministic codes. The elementary cell has been calculated with two main goals; evaluation of effects of simplifications introduced in deterministic lattice spectrum calculations by the WIMS code and evaluation of library data in recently developed WIMS libraries. In particular the beryllium data of those libraries needed evaluation. The whole core calculations mainly the first MARIA critical experiment and the first critical core after the 8-year break in operation. Both cores contained only fresh fuel elements but only in the first critical core the beryllium blocks were not poisoned by Li-6 and He-3. Thus the MCNP k-eff results could be compared with the experiment. The MCNP calculations for the cores with beryllium poisoned suffered the deficiency of uncertainty in the poison concentration, but a comparison of power distribution shows that realistic poison levels have been carried out for the operating reactor MARIA configurations. (author)

  14. Dose-response regressions for algal growth and similar continuous endpoints: Calculation of effective concentrations

    DEFF Research Database (Denmark)

    Christensen, Erik R.; Kusk, Kresten Ole; Nyholm, Niels

    2009-01-01

    We derive equations for the effective concentration giving 10% inhibition (EC10) with 95% confidence limits for probit (log-normal), Weibull, and logistic dose -responsemodels on the basis of experimentally derived median effective concentrations (EC50s) and the curve slope at the central point (50......% inhibition). For illustration, data from closed, freshwater algal assays are analyzed using the green alga Pseudokirchneriella subcapitata with growth rate as the response parameter. Dose-response regressions for four test chemicals (tetraethylammonium bromide, musculamine, benzonitrile, and 4...... regression program with variance weighting and proper inverse estimation. The Weibull model provides the best fit to the data for all four chemicals. Predicted EC10s (95% confidence limits) from our derived equations are quite accurate; for example, with 4-4-(trifluoromethyl)phenoxy-phenol and the probit...

  15. Design and development of a radio-ecological domestic user friendly code for calculation of radiation doses and concentration due to airborn radionuclides release during the accidental and normal operation in nuclear installations

    International Nuclear Information System (INIS)

    Shad, A. Haghighi; Allaf, M. Athari; Masti, D.; Sepanloo, K.; Feghhi, S.A.H.; Khodadadi, R.

    2018-01-01

    A domestic user friendly dynamic radiological dose and model has been developed to estimate radiation doses and stochastic risks due to atmospheric and liquid discharges of radionuclides in the case of a nuclear reactor accident and normal operation. In addition to individual doses from different pathways for different age groups, collective doses and stochastic risks can be calculated by the developed domestic user friendly KIANA Advance Computational Computer Code and model. The current Code can be coupled to any long-range atmospheric dispersion/short term model which can calculate radionuclide concentrations in air and on the ground and in the water surfaces predetermined time intervals or measurement data.

  16. Design and development of a radio-ecological domestic user friendly code for calculation of radiation doses and concentration due to airborn radionuclides release during the accidental and normal operation in nuclear installations

    Energy Technology Data Exchange (ETDEWEB)

    Shad, A. Haghighi; Allaf, M. Athari [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Dept. of Nuclear Engineering; Masti, D. [Azad Univ., Boushehr (Iran, Islamic Republic of). Research and Developement in BNPP-1; Sepanloo, K. [Nuclear Science and Technology Research Institute (NSTRI), Tehran (Iran, Islamic Republic of). Reactor and Nuclear Safety School; Feghhi, S.A.H. [Shahid Beheshti Univ., Tehran (Iran, Islamic Republic of). Dept. of Nuclear Engineering; Khodadadi, R. [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Science and Research Branch

    2018-02-15

    A domestic user friendly dynamic radiological dose and model has been developed to estimate radiation doses and stochastic risks due to atmospheric and liquid discharges of radionuclides in the case of a nuclear reactor accident and normal operation. In addition to individual doses from different pathways for different age groups, collective doses and stochastic risks can be calculated by the developed domestic user friendly KIANA Advance Computational Computer Code and model. The current Code can be coupled to any long-range atmospheric dispersion/short term model which can calculate radionuclide concentrations in air and on the ground and in the water surfaces predetermined time intervals or measurement data.

  17. Stomatal and pavement cell density linked to leaf internal CO2 concentration.

    Science.gov (United States)

    Santrůček, Jiří; Vráblová, Martina; Simková, Marie; Hronková, Marie; Drtinová, Martina; Květoň, Jiří; Vrábl, Daniel; Kubásek, Jiří; Macková, Jana; Wiesnerová, Dana; Neuwithová, Jitka; Schreiber, Lukas

    2014-08-01

    Stomatal density (SD) generally decreases with rising atmospheric CO2 concentration, Ca. However, SD is also affected by light, air humidity and drought, all under systemic signalling from older leaves. This makes our understanding of how Ca controls SD incomplete. This study tested the hypotheses that SD is affected by the internal CO2 concentration of the leaf, Ci, rather than Ca, and that cotyledons, as the first plant assimilation organs, lack the systemic signal. Sunflower (Helianthus annuus), beech (Fagus sylvatica), arabidopsis (Arabidopsis thaliana) and garden cress (Lepidium sativum) were grown under contrasting environmental conditions that affected Ci while Ca was kept constant. The SD, pavement cell density (PCD) and stomatal index (SI) responses to Ci in cotyledons and the first leaves of garden cress were compared. (13)C abundance (δ(13)C) in leaf dry matter was used to estimate the effective Ci during leaf development. The SD was estimated from leaf imprints. SD correlated negatively with Ci in leaves of all four species and under three different treatments (irradiance, abscisic acid and osmotic stress). PCD in arabidopsis and garden cress responded similarly, so that SI was largely unaffected. However, SD and PCD of cotyledons were insensitive to Ci, indicating an essential role for systemic signalling. It is proposed that Ci or a Ci-linked factor plays an important role in modulating SD and PCD during epidermis development and leaf expansion. The absence of a Ci-SD relationship in the cotyledons of garden cress indicates the key role of lower-insertion CO2 assimilation organs in signal perception and its long-distance transport. © The Author 2014. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  18. The possible evolution and future of CO2-concentrating mechanisms.

    Science.gov (United States)

    Raven, John A; Beardall, John; Sánchez-Baracaldo, Patricia

    2017-06-01

    CO2-concentrating mechanisms (CCMs), based either on active transport of inorganic carbon (biophysical CCMs) or on biochemistry involving supplementary carbon fixation into C4 acids (C4 and CAM), play a major role in global primary productivity. However, the ubiquitous CO2-fixing enzyme in autotrophs, Rubisco, evolved at a time when atmospheric CO2 levels were very much higher than today and O2 was very low and, as CO2 and O2 approached (by no means monotonically), today's levels, at some time subsequently many organisms evolved a CCM that increased the supply of CO2 and decreased Rubisco oxygenase activity. Given that CO2 levels and other environmental factors have altered considerably between when autotrophs evolved and the present day, and are predicted to continue to change into the future, we here examine the drivers for, and possible timing of, evolution of CCMs. CCMs probably evolved when CO2 fell to 2-16 times the present atmospheric level, depending on Rubisco kinetics. We also assess the effects of other key environmental factors such as temperature and nutrient levels on CCM activity and examine the evidence for evolutionary changes in CCM activity and related cellular processes as well as limitations on continuity of CCMs through environmental variations. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  19. Data on fluoride concentration levels in semi-arid region of Medak, Telangana, South India

    Directory of Open Access Journals (Sweden)

    Adimalla Narsimha

    2018-02-01

    Full Text Available According to the World Health Organization recommendation, the optimal fluoride concentration levels in drinking water have to be in the range of 0.5 and 1.5 mg/L since this permissible range is essential for normal mineralization of bones and teeth as well as for dental enamel formation in human's body Bell and budwig, 1970; Adimalla and Venkatayogi, 2017; Narsimha and Sudarshan, 2013, 2016; 2017 [1,2,4,5,6]. If continues intake of high fluoride (>1.5 water can severely cause dental and skeletal fluorosis. The investigated area people majorly depend on groundwater for drinking purposes and fluoride concentration ranged from 0.2 to 7.4 mg/L with mean concentration of 2.7 mg/L and data was compared with WHO guidelines for drinking purposes. Overall, data reveals that the 57% of groundwater samples data was not safe for drinking purposes. Therefore, distribution of fluoride in the groundwater of Medak region in Telangana was suggested to intake drinking water, which are below level of fluoride concentration in the groundwater and take care about health implications.

  20. Design of a nonimaging Fresnel lens for solar concentrators

    Energy Technology Data Exchange (ETDEWEB)

    Leutz, R.; Akisawa, Atushi; Kashiwagi, Takao [Tokyo University of Agriculture and Technology (Japan). Dept. of Mechanical Systems Engineering; Suzuki, Akio [UNESCO, Paris (France)

    1999-04-01

    An optimum convex shaped nonimaging Fresnel lens is designed following the edge ray principle. The lens is evaluated by tracing rays and calculating a projective optical concentration ratio. This Fresnel lens is intended for use in evacuated tube type solar concentrators, generating mid-temperature heat to drive sorption cycles, or provide industrial process heat. It can also be used along with a secondary concentrator in photovoltaic applications. (author)

  1. optical analysis of a hemispheric concentrator with a manual ...

    African Journals Online (AJOL)

    PROF. BARTH EKWEME

    sophisticated system involving robotics, managed by a. PLC using algorithms of calculation for the orientation of each element is necessary. Studies on hemispheric concentrators were conducted, usually to show that they focus at a point just like a paraboloid concentrator (Bellel, 2011). The angle change does not cause a ...

  2. CFD Calculation of Internal Natural Convection in the Annulus between Horizontal Concentric Cylinders

    International Nuclear Information System (INIS)

    Francis, N.D. Jr.; Itamura, M.T.; Webb, S.W.; James, D.L.

    2002-01-01

    The objective of this heat transfer and fluid flow study is to assess the ability of a computational fluid dynamics (CFD) code to reproduce the experimental results, numerical simulation results, and heat transfer correlation equations developed in the literature for natural convection heat transfer within the annulus of horizontal concentric cylinders. In the literature, a variety of heat transfer expressions have been developed to compute average equivalent thermal conductivities. However, the expressions have been primarily developed for very small inner and outer cylinder radii and gap-widths. In this comparative study, interest is primarily focused on large gap widths (on the order of half meter or greater) and large radius ratios. From the steady-state CFD analysis it is found that the concentric cylinder models for the larger geometries compare favorably to the results of the Kuehn and Goldstein correlations in the Rayleigh number range of about 10 5 to 10 8 (a range that encompasses the laminar to turbulent transition). For Rayleigh numbers greater than 10 8 , both numerical simulations and experimental data (from the literature) are consistent and result in slightly lower equivalent thermal conductivities than those obtained from the Kuehn and Goldstein correlations

  3. Predicting radon/radon daughter concentrations in underground mines

    International Nuclear Information System (INIS)

    Leach, V.A.

    1984-01-01

    A detailed description of a computer programme is outlined for the calculation of radon/radon daughter concentrations in air. This computer model is used to predict the radon/radon daughter concentrations in Working Level (WL) at the workplace and at the various junctions at either end of the branches in a typical ventilation network proposed for the Jabiluka mine in the Northern Territory

  4. Adequate plasma drug concentrations suggest that amoxicillin can be administered by continuous infusion using elastomeric pumps.

    Science.gov (United States)

    Arensdorff, Lyne; Boillat-Blanco, Noémie; Decosterd, Laurent; Buclin, Thierry; de Vallière, Serge

    2017-09-01

    Elastomeric pumps can be useful for the administration of antibiotics in the outpatient setting. To determine amoxicillin degradation in elastomeric pumps, as well as the effectiveness of amoxicillin treatment administered by elastomeric pumps. Antibiotic degradation was measured in elastomeric pumps filled with 6 g of amoxicillin in 240 mL of NaCl 0.9% by drawing samples at 12 h intervals when stored in the fridge for 48 h and when worn around the waist for 24 h. Subsequently nine patients were treated with continuous infusions of 8 or 12 g of amoxicillin per day. Plasma amoxicillin concentrations were measured on each visit to the outpatient parenteral antibiotic therapy unit. Clinical outcome was verified 3 months after the end of treatment. Amoxicillin degradation in elastomeric pumps reached 10% after 48 h in the fridge and an additional 30% when worn around the waist for 24 h. Mean plasma drug concentrations achieved with 12 g of amoxicillin per day were 18.5 mg/L (95% CI 13.5-23.5), which is largely above the MIC of amoxicillin-susceptible bacteria. Nine patients treated for various complicated infections were cured and had no unexpected adverse effects. Adequate plasma drug concentrations and favourable clinical outcomes suggest that amoxicillin can be administered by continuous infusion using elastomeric pumps. This treatment modality does not fulfil formal requirements regarding pharmaceutical stability, but the resulting safety impact in patients is probably limited. Therapeutic drug monitoring and a close clinical follow-up are recommended if this route of administration is chosen. © The Author 2017. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Determing and monitoring of maximum permissible power for HWRR-3

    International Nuclear Information System (INIS)

    Jia Zhanli; Xiao Shigang; Jin Huajin; Lu Changshen

    1987-01-01

    The operating power of a reactor is an important parameter to be monitored. This report briefly describes the determining and monitoring of maximum permissiable power for HWRR-3. The calculating method is described, and the result of calculation and analysis of error are also given. On-line calculation and real time monitoring have been realized at the heavy water reactor. It provides the reactor with a real time and reliable supervision. This makes operation convenient and increases reliability

  6. Optimizing concentration of shifter additive for plastic scintillators of different size

    Science.gov (United States)

    Adadurov, A. F.; Zhmurin, P. N.; Lebedev, V. N.; Titskaya, V. D.

    2009-02-01

    This paper concerns the influence of wavelength shifting (secondary) luminescent additive (LA 2) on the light yield of polystyrene-based plastic scintillator (PS) taking self-absorption into account. Calculations of light yield dependence on concentration of 1.4-bis(2-(5-phenyloxazolyl)-benzene (POPOP) as LA 2 were made for various path lengths of photons in PS. It is shown that there is an optimal POPOP concentration ( Copt), which provides a maximum light yield for a given path length. This optimal concentration is determined by the competition of luminescence and self-reflection processes. Copt values were calculated for PS of different dimensions. For small PS, Copt≈0.02%, which agree with a common (standard) value of POPOP concentration. For higher PS dimensions, the optimal POPOP concentration is decreased (to Copt≈0.006% for 320×30×2 cm sample), reducing the light yield from PS by almost 35%.

  7. Criticality calculation method for mixer-settlers

    International Nuclear Information System (INIS)

    Gonda, Kozo; Aoyagi, Haruki; Nakano, Ko; Kamikawa, Hiroshi.

    1980-01-01

    A new criticality calculation code MACPEX has been developed to evaluate and manage the criticality of the process in the extractor of mixer-settler type. MACPEX can perform the combined calculation with the PUREX process calculation code MIXSET, to get the neutron flux and the effective multiplication constant in the mixer-settlers. MACPEX solves one-dimensional diffusion equation by the explicit difference method and the standard source-iteration technique. The characteristics of MACPEX are as follows. 1) Group constants of 4 energy groups for the 239 Pu-H 2 O solution, water, polyethylene and SUS 28 are provided. 2) The group constants of the 239 Pu-H 2 O solution are given by the functional formulae of the plutonium concentration, which is less than 50 g/l. 3) Two boundary conditions of the vacuum condition and the reflective condition are available in this code. 4) The geometrical bucklings can be calculated for a certain energy group and/or region by using the three dimentional neutron flux profiles obtained by CITATION. 5) The buckling correction search can be carried out in order to get a desired k sub(eff). (author)

  8. The concentration of fission products and other radionuclides in the surface air between 1971 and 1973

    International Nuclear Information System (INIS)

    Kolb, W.

    1974-01-01

    The aerosols collected with high-efficiency portable dust samplers in Brunswick and Tromsoe are analyzed in a Ge(Li) spectrometer. The mean monthly activity concentrations are given for a number of cosmogenic and induced radionuclides from nuclear weapons tests as well as for some cosmogenic and natural radionuclides. The annual curve exhibits marked seasonal variations with a pronounced peak - caused by an influx from the stratospheric reservoir - in late spring for all radionuclides studied except for 35 S, 210 Pb and 226 Ra. This peak decreases continuously from 1971 - 1973 for the fission products and induced radionuclides which for the most part had been produced in Chinese nuclear weapons tests. In contrast to 7 Be and 22 Na, the behaviour of 35 S suggests that it is partly anthropogenic in origin. The activity concentration of 226 Ra in air has been measured directly for the first time. The findings are discussed and finally compared with the maximum permissible concentration for the population. (orig./AK) [de

  9. Correction of rhodium detector signals for comparison to design calculations

    International Nuclear Information System (INIS)

    Judd, J.L.; Chang, R.Y.; Gabel, C.W.

    1989-01-01

    Rhodium detectors are used in many commercial pressurized water reactors PWRs [pressurized water reactor] as in-core neutron detectors. The signals from the detectors are the result of neutron absorption in 103 Rh and the subsequent beta decay of 104 Rh to 104 Pd. The rhodium depletes ∼1% per full-power month, so corrections are necessary to the detector signal to account for the effects of the rhodium depletion. These corrections result from the change in detector self-shielding with rhodium burnup and the change in rhodium concentration itself. Correction for the change in rhodium concentration is done by multiplication of the factor N(t)/N 0 , where N(t) is the rhodium concentration at time t and N 0 is the initial rhodium concentration. The calculation of the self-shielding factor is more complicated and is presented. A self-shielding factor based on the fraction of rhodium remaining was calculated with the CASMO-3 code. The results obtained from our comparisons of predicted and measured in-core detector signals show that the CASMO-3/SIMULATE-3 code package is an effective tool for estimating pin peaking and power distributions

  10. Effects of Electronic Cigarette Liquid Nicotine Concentration on Plasma Nicotine and Puff Topography in Tobacco Cigarette Smokers: A Preliminary Report.

    Science.gov (United States)

    Lopez, Alexa A; Hiler, Marzena M; Soule, Eric K; Ramôa, Carolina P; Karaoghlanian, Nareg V; Lipato, Thokozeni; Breland, Alison B; Shihadeh, Alan L; Eissenberg, Thomas

    2016-05-01

    Electronic cigarettes (ECIGs) aerosolize a liquid that usually contains propylene glycol and/or vegetable glycerin, flavorants, and the dependence-producing drug nicotine in various concentrations. This study examined the extent to which ECIG liquid nicotine concentration is related to user plasma nicotine concentration in ECIG-naïve tobacco cigarette smokers. Sixteen ECIG-naïve cigarette smokers completed four laboratory sessions that differed by the nicotine concentration of the liquid (0, 8, 18, or 36 mg/ml) that was placed into a 1.5 Ohm, dual coil "cartomizer" powered by a 3.3V battery. In each session, participants completed two, 10-puff ECIG use bouts with a 30-second inter-puff interval; bouts were separated by 60 minutes. Venous blood was sampled before and after bouts for later analysis of plasma nicotine concentration; puff duration, volume, and average flow rate were measured during each bout. In bout 1, relative to the 0mg/ml nicotine condition (mean = 3.8 ng/ml, SD = 3.3), plasma nicotine concentration increased significantly immediately after the bout for the 8 (mean = 8.8 ng/ml, SD = 6.3), 18 (mean = 13.2 ng/ml, SD = 13.2), and 36 mg/ml (mean = 17.0 ng/ml, SD = 17.9) liquid concentration. A similar pattern was observed after bout 2. Average puff duration in the 36 mg/ml condition was significantly shorter compared to the 0mg/ml nicotine condition. Puff volume increased during the second bout for 8 and 18 mg/ml conditions. For a given ECIG device, nicotine delivery may be directly related to liquid concentration. ECIG-naïve cigarette smokers can, from their first use bout, attain cigarette-like nicotine delivery profiles with some currently available ECIG products. Liquid nicotine concentration can influence plasma nicotine concentration in ECIG-naïve cigarette smokers, and, at some concentrations, the nicotine delivery profile of a 3.3V ECIG with a dual coil, 1.5-Ohm cartomizer approaches that of a combustible tobacco cigarette in this

  11. A new method for calculation of an air quality index

    Energy Technology Data Exchange (ETDEWEB)

    Ilvessalo, P. [Finnish Meteorological Inst., Helsinki (Finland). Air Quality Dept.

    1995-12-31

    Air quality measurement programs in Finnish towns have expanded during the last few years. As a result of this it is more and more difficult to make use of all the measured concentration data. Citizens of Finnish towns are nowadays taking more of an interest in the air quality of their surroundings. The need to describe air quality in a simplified form has increased. Air quality indices permit the presentation of air quality data in such a way that prevailing conditions are more easily understandable than when using concentration data as such. Using an air quality index always means that some of the information about concentrations of contaminants in the air will be lost. How much information is possible to extract from a single index number depends on the calculation method. A new method for the calculation of an air quality index has been developed. This index always indicates the overstepping of an air quality guideline level. The calculation of this air quality index is performed using the concentrations of all the contaminants measured. The index gives information both about the prevailing air quality and also the short-term trend. It can also warn about the expected exceeding of guidelines due to one or several contaminants. The new index is especially suitable for the real-time monitoring and notification of air quality values. The behaviour of the index was studied using material from a measurement period in the spring of 1994 in Kaepylae, Helsinki. Material from a pre-operational period in the town of Oulu was also available. (author)

  12. A new method for calculation of an air quality index

    Energy Technology Data Exchange (ETDEWEB)

    Ilvessalo, P [Finnish Meteorological Inst., Helsinki (Finland). Air Quality Dept.

    1996-12-31

    Air quality measurement programs in Finnish towns have expanded during the last few years. As a result of this it is more and more difficult to make use of all the measured concentration data. Citizens of Finnish towns are nowadays taking more of an interest in the air quality of their surroundings. The need to describe air quality in a simplified form has increased. Air quality indices permit the presentation of air quality data in such a way that prevailing conditions are more easily understandable than when using concentration data as such. Using an air quality index always means that some of the information about concentrations of contaminants in the air will be lost. How much information is possible to extract from a single index number depends on the calculation method. A new method for the calculation of an air quality index has been developed. This index always indicates the overstepping of an air quality guideline level. The calculation of this air quality index is performed using the concentrations of all the contaminants measured. The index gives information both about the prevailing air quality and also the short-term trend. It can also warn about the expected exceeding of guidelines due to one or several contaminants. The new index is especially suitable for the real-time monitoring and notification of air quality values. The behaviour of the index was studied using material from a measurement period in the spring of 1994 in Kaepylae, Helsinki. Material from a pre-operational period in the town of Oulu was also available. (author)

  13. Estimation of polonium concentration in groundwater samples from the Peddagattu/Nambapur and Seripalli regions using alpha-spectrometry

    International Nuclear Information System (INIS)

    Raghavendra, T.; Srilatha, K.; Mahender, C.; Elender; Vijaya Lakshmi, T.; Himabindu, V.; Vishwa Prasad; Padma Savithri, P.; Datta, D.; Arunachalam, J.

    2013-01-01

    The decay of uranium series in the earth crust remains the final and long lived radionuclides 210 Po and 210 Pb in the environment. Their presence in the atmosphere is due to the decay of 222 Rn diffusing from the ground. This study was carried out with an objective of estimation of polonium concentration in a uranium mineralized zone in Peddagattu and Seripalli areas of Nalgonda district, Andhra Pradesh, India. Groundwater samples were collected from 12 wells, and frequency of these collections was once in a quarter from May 2010 to Dec 2011. The alpha-spectrometry has been applied to analyze these samples. Observation reveals that the activity concentration of Polonium in the water samples of Peddagattu and Seripally regions range from 0.3 mBq/l to 2.80 mBq/l with Geometric mean of 0.89 mBq/l and Geometric Standard deviation of 2.72 and from 0.3 mBq/l to 4.68 mBq/l with a Geometric mean of 0.91 and Geometric standard deviation of 3.22 respectively. As per WHO standards, the maximum permissible limit in drinking water for Polonium is 0.55 Bq/l. Hence all the 12 samples are falling well under the permissible limit. This paper presents the analytical details for estimating polonium as a natural radioactive element in groundwater as well as surface water samples collected from the Nambapur/Peddagattu and Seripalli regions. (author)

  14. Evaluation and reffinement of the neutronic calculation methodology

    International Nuclear Information System (INIS)

    Conti Filho, P.

    1984-01-01

    A computational code that has the homogenized cross section given by the LEOPARD code as input was developed. The code gives polinomial coefficients that represent the homogenized cross section as a function of the local burnup and the boron concentration for the assembly, for each step in the reactor Burnup. Lately, were developed an interface between the LEOPARD code Polinomiun Generator program and CITATION code to became possible to CITATION code to set the homogenized microscopic cross section as function of the local caracteristics of the assembly on the way to make the calculation of the reactor Burnup. For a choosen reactor (1900MWth) have been done the inicial calculation (super-cells calculation and others Input) and after that were done the calculation with and without the polinomia. The analyses of the results of the CITATION code were done and the principal results were presented here. (Author) [pt

  15. Effective calculation algorithm for nuclear chains of arbitrary length and branching

    International Nuclear Information System (INIS)

    Chirkov, V.A.; Mishanin, B.V.

    1994-01-01

    An effective algorithm for calculation of the isotope concentration in the spent nuclear fuel when it is kept in storage, is presented. Using the superposition principle and representing the transfer function in a rather compact form it becomes possible achieve high calculation speed and a moderate computer code size. The algorithm is applied for the calculation of activity, energy release and toxicity of heavy nuclides and products of their decay when the fuel is kept in storage. (authors). 1 ref., 4 tabs

  16. Comparison of predicted and measured variations of indoor radon concentration

    International Nuclear Information System (INIS)

    Arvela, H.; Voutilainen, A.; Maekelaeinen, I.; Castren, O.; Winqvist, K.

    1988-01-01

    Prediction of the variations of indoor radon concentration were calculated using a model relating indoor radon concentration to radon entry rate, air infiltration and meteorological factors. These calculated variations have been compared with seasonal variations of 33 houses during 1-4 years, with winter-summer concentration ratios of 300 houses and the measured diurnal variation. In houses with a slab in ground contact the measured seasonal variations are quite often in agreement with variations predicted for nearly pure pressure difference driven flow. The contribution of a diffusion source is significant in houses with large porous concrete walls against the ground. Air flow due to seasonally variable thermal convection within eskers strongly affects the seasonal variations within houses located thereon. Measured and predicted winter-summer concentration ratios demonstrate that, on average, the ratio is a function of radon concentration. The ratio increases with increasing winter concentration. According to the model the diurnal maximum caused by a pressure difference driven flow occurs in the morning, a finding which is in agreement with the measurements. The model presented can be used for differentiating between factors affecting radon entry into houses. (author)

  17. ARCON96, Radioactive Plume Concentration in Reactor Control Rooms

    International Nuclear Information System (INIS)

    Ramsdell, J.V.; Simonen, C.A.

    2003-01-01

    1 - Description of program or function: ARCON96 was developed to calculate relative concentrations in plumes from nuclear power plants at control room air intakes in the vicinity of the release point. 2 - Methods: ARCON96 implements a straight-line Gaussian dispersion model with dispersion coefficients that are modified to account for low wind meander and building wake effects. Hourly, normalized concentrations (X/Q) are calculated from hourly meteorological data. The hourly values are averaged to form X/Qs for periods ranging from 2 to 720 hours in duration. The calculated values for each period are used to form cumulative frequency distributions. 3 - Restriction on the complexity of the problem: ARCON96 is a single user program. If expanded output is selected by the user, the file includes the hourly input and X/Qs and the intermediate computational results. The output file may exceed a megabyte size

  18. Criteria for permission of radiosterilized products to application in medicine; Zasady dopuszczania wyrobow sterylizowanych radiacyjnie do stosowania w medycynie

    Energy Technology Data Exchange (ETDEWEB)

    Achmatowicz, T [Instytut Lekow, Warsaw (Poland)

    1997-10-01

    The criteria being used in Poland for permission of radiosterilized medical materials to commercial application result from regulations being in force. The international regulations are also taken into account. The all criteria and procedure needed for any product become accepted for radiosterilization and commercial medical use have been presented and discussed. 1 tab.

  19. A Web tool for calculating k0-NAA uncertainties

    International Nuclear Information System (INIS)

    Younes, N.; Robouch, P.

    2003-01-01

    The calculation of uncertainty budgets is becoming a standard step in reporting analytical results. This gives rise to the need for simple, easily accessed tools to calculate uncertainty budgets. An example of such a tool is the Excel spreadsheet approach of Robouch et al. An internet application which calculates uncertainty budgets for k 0 -NAA is presented. The Web application has built in 'Literature' values for standard isotopes and accepts as inputs fixed information such as the thermal to epithermal neutron flux ratio, as well as experiment specific data such as the mass of the sample. The application calculates and displays intermediate uncertainties as well as the final combined uncertainty of the element concentration in the sample. The interface only requires access to a standard browser and is thus easily accessible to researchers and laboratories. This may facilitate and standardize the calculation of k 0 -NAA uncertainty budgets. (author)

  20. Atmospheric dispersion calculations in a low mountain area

    International Nuclear Information System (INIS)

    Schmid, S.

    1987-01-01

    The applicability of the Gaussian model for assessing the short-range environmental exposure from an emission source in a topographically inhomogeneous terrain is tested. An atmospheric dispersion model of general applicability is used, which is based on results of hydrodynamic flow models. Approaches for turbulence and radiation parameterization are tested by means of a vertically one-dimensional flow model. In order to introduce the effects of the topography in the boundary-layer simulations, the three-dimensional mesoscale model (Ulrich) is applied. The two models are verified by way of episode simulation using wind profile measurements. The differences in the models' results are to show the topographic influence. The calculated flow fields serve as input to a randomwalk model applied for calculating ground-level concentration fields in the vicinity of an emission source. The Gaussian model underestimates the pollution under stable conditions. Convectivity conditions may change the effective source hight through vertical effects caused by orography which, depending on the direction of free flow, leads to an increase or decrease of pollutant concentration at ground level. Applying the more complex dispersion model, the concentration maxima under stable conditions are closer to the source by a factor five, and under unstable conditions about one and a half times more remote. (orig./HP) [de